Science.gov

Sample records for abrasion scratch test

  1. Review of scratch test studies of abrasion mechanisms

    SciTech Connect

    Kosel, T.H.

    1986-01-01

    The use of scratch tests to simulate the material removal mechanisms which occur during abrasion is reviewed. Although useful studies of the effect of the rake angle on material removal have been carried out using diamond tools, closer simulation of the mechanisms of material removal can be obtained using actual irregular individual abrasive particles as scratch tools. Previous studies are reviewed in which scratch tests have been performed with both conventional scratch test instruments and a specially designed system used for )ital in situ) scratch tests in the scanning electron microscope (SEM). Multiple-pass scratch tests over the same scratch path have been shown to create surface features and wear debris particles which are very similar to those produced by low-stress abrasion. Alumina (Al/sub 2/O/sub 3/) particles have been shown to produce continuous micromachining chips from the hard, brittle carbide phase of Stellite alloys, establishing direct cutting as the important mechanism of material removal for this type of abrasive. An )ital in situ) study of material removal from white cast irons by quartz particles has provided conclusive evidence that carbide removal does not occur by direct cutting but rather always involves microfracture. Previously unpublished work which has compared scratch tests with crushed quartz and alumina particles is included. Also described is a new scratch test system which controls the depth of cut rather than the scratch load in order to simulate high-stress abrasion, in which abrasive particles are constrained to a fixed depth of cut. Preliminary new results show substantially different carbide fracture behavior under fixed-depth conditions. 8 figs., 20 refs.

  2. Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

    NASA Technical Reports Server (NTRS)

    Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W., Jr.

    2011-01-01

    The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width as currently defined by the ASTM G 171 Standard. The ZOI has been found to be at least twice the size of a standard width measurement, in some cases considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for detailed analysis. Documenting additional changes to various surface roughness parameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Data are presented to show that different combinations of scratch tips and abraded materials can actually yield the same scratch width, but result in different volume displacement or removal measurements and therefore, the ZOI method is more discriminating than the ASTM method scratch width. Furthermore, by investigating the use of custom scratch tips for our specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized manner, and not just by scratch width alone, is reinforced. This benefit is made apparent when a tip creates an intricate contour having multiple peaks and valleys within a single scratch. This work lays the foundation for updating scratch measurement standards to improve modeling and characterization of three-body abrasion test results.

  3. Standardization of a Volumetric Displacement Measurement for Two-Body Abrasion Scratch Test Data Analysis

    NASA Technical Reports Server (NTRS)

    Street, K. W. Jr.; Kobrick, R. L.; Klaus, D. M.

    2011-01-01

    A limitation has been identified in the existing test standards used for making controlled, two-body abrasion scratch measurements based solely on the width of the resultant score on the surface of the material. A new, more robust method is proposed for analyzing a surface scratch that takes into account the full three-dimensional profile of the displaced material. To accomplish this, a set of four volume- displacement metrics was systematically defined by normalizing the overall surface profile to denote statistically the area of relevance, termed the Zone of Interaction. From this baseline, depth of the trough and height of the plowed material are factored into the overall deformation assessment. Proof-of-concept data were collected and analyzed to demonstrate the performance of this proposed methodology. This technique takes advantage of advanced imaging capabilities that allow resolution of the scratched surface to be quantified in greater detail than was previously achievable. When reviewing existing data analysis techniques for conducting two-body abrasive scratch tests, it was found that the ASTM International Standard G 171 specified a generic metric based only on visually determined scratch width as a way to compare abraded materials. A limitation to this method was identified in that the scratch width is based on optical surface measurements, manually defined by approximating the boundaries, but does not consider the three-dimensional volume of material that was displaced. With large, potentially irregular deformations occurring on softer materials, it becomes unclear where to systematically determine the scratch width. Specifically, surface scratches on different samples may look the same from a top view, resulting in an identical scratch width measurement, but may vary in actual penetration depth and/or plowing deformation. Therefore, two different scratch profiles would be measured as having identical abrasion properties, although they differ

  4. Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

    NASA Technical Reports Server (NTRS)

    Street, Kenneth W., Jr.; Kobrick, Ryan L.; Klaus, David M.

    2013-01-01

    Abrasion of mechanical components and fabrics by soil on Earth is typically minimized by the effects of atmosphere and water. Potentially abrasive particles lose sharp and pointed geometrical features through erosion. In environments where such erosion does not exist, such as the vacuum of the Moon, particles retain sharp geometries associated with fracturing of their parent particles by micrometeorite impacts. The relationship between hardness of the abrasive and that of the material being abraded is well understood, such that the abrasive ability of a material can be estimated as a function of the ratio of the hardness of the two interacting materials. Knowing the abrasive nature of an environment (abrasive)/construction material is crucial to designing durable equipment for use in such surroundings. The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width. The ZOI has been found to be at least twice the size of a standard width measurement; in some cases, considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for de tailed analysis. Documenting additional changes to various surface roughness par ameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Further - more, by investigating the use of custom scratch tips for specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized

  5. Standardization of a Volumetric Displacement Measurement for Two-Body Abrasion Scratch Test Data Analysis

    NASA Technical Reports Server (NTRS)

    Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W., Jr.

    2010-01-01

    A limitation has been identified in the existing test standards used for making controlled, two-body abrasion scratch measurements based solely on the width of the resultant score on the surface of the material. A new, more robust method is proposed for analyzing a surface scratch that takes into account the full three-dimensional profile of the displaced material. To accomplish this, a set of four volume displacement metrics are systematically defined by normalizing the overall surface profile to statistically denote the area of relevance, termed the Zone of Interaction (ZOI). From this baseline, depth of the trough and height of the ploughed material are factored into the overall deformation assessment. Proof of concept data were collected and analyzed to demonstrate the performance of this proposed methodology. This technique takes advantage of advanced imaging capabilities that now allow resolution of the scratched surface to be quantified in greater detail than was previously achievable. A quantified understanding of fundamental particle-material interaction is critical to anticipating how well components can withstand prolonged use in highly abrasive environments, specifically for our intended applications on the surface of the Moon and other planets or asteroids, as well as in similarly demanding, harsh terrestrial settings

  6. A comparison of carbide fracture during fixed depth and fixed load scratch tests

    SciTech Connect

    Prasad, S.V.; Kosel, T.H.

    1985-01-01

    In order to simulate abrasion of dual-phase materials containing large carbides under fixed depth conditions an apparatus has been designed and used to perform scratch tests at a fixed depth of cut on such materials. The scratch test consists of two support arms tipped with small steel balls held in contact with surface by /sup 700/ g, while the scratch tool is mounted on the tip of a central arm whose adjustable length allow control of the depth of cut. The scratch tool does not deflect significant when it encounters a large carbide. Scratch tests with the new apparatus have been performed on Co-base Stellite alloys containing large Cr-rich carbides, using individual particles of alumina as scratch tools to generate fixed depth scratches. A in situ SEM scratch test apparatus has also been used to genrate fixed load scratches. Comparison of the scratches shows that for comparable average scratch depths, under fixed load conditions the scratch tool deflects over the carbides without causing fracture, but that since it cannot deflect under fixed depth conditions it induces gross carbide fracture. Results suggest that the fixed depth scratch test can be successfully employed to simulate fixed depth abrasion, which has been previously shown to generate gross carbide fracture in these alloys. The in situ SEM scratch test simulates fixed load abrasion conditions such as those which occur in rubber wheel abrasion tests. 12 refs., 9 figs

  7. Conduit Coating Abrasion Testing

    NASA Technical Reports Server (NTRS)

    Sullivan, Mary K.

    2013-01-01

    During my summer internship at NASA I have been working alongside the team members of the RESTORE project. Engineers working on the RESTORE project are creating ·a device that can go into space and service satellites that no longer work due to gas shortage or other technical difficulties. In order to complete the task of refueling the satellite a hose needs to be used and covered with a material that can withstand effects of space. The conduit coating abrasion test will help the researchers figure out what type of thermal coating to use on the hose that will be refueling the satellites. The objective of the project is to determine whether or not the conduit coating will withstand the effects of space. For the RESTORE project I will help with various aspects of the testing that needed to be done in order to determine which type of conduit should be used for refueling the satellite. During my time on the project I will be assisting with wiring a relay board that connected to the test set up by soldering, configuring wires and testing for continuity. Prior to the testing I will work on creating the testing site and help write the procedure for the test. The testing will take place over a span of two weeks and lead to an informative conclusion. Working alongside various RESTORE team members I will assist with the project's documentation and records. All in all, throughout my internship at NASA I hope to learn a number of valuable skills and be a part of a hard working team of engineers.

  8. Scratch and abrasion properties of polyurethane-based micro- and nano-hybrid obturation materials.

    PubMed

    Estevez, Miriam; Rodriguez, J Rogelio; Vargas, Susana; Guerra, J A; Brostow, Witold; Lobland, Haley E Hagg

    2013-06-01

    Polyurethane-based micro- and nano-hybrid composites were produced with controlled porosity to be used as obturation materials. In addition to hydroxyapatite (HAp) micro-particles in the composites, two different ceramics particle types were also added: alumina micro-particles and silica nano-particles. Particles of different sizes provide the materials with improved mechanical properties: the use of micro- and nano-particles produces a better packing because the nano-particles fill the interstitial space left by the micro-particles, rendering an improvement in the mechanical properties. The silica and alumina particles provide the materials with appropriate abrasion and scratching properties, while the HAp provides the required bio-acceptance. The polymeric matrix was a mono-component solvent-free polyurethane. The porosity was selected by controlling the chemical reaction. PMID:23862519

  9. Three-Body Abrasion Testing Using Lunar Dust Simulants to Evaluate Surface System Materials

    NASA Technical Reports Server (NTRS)

    Kobrick, Ryan L.; Budinski, Kenneth G.; Street, Kenneth W., Jr.; Klaus, David M.

    2010-01-01

    Numerous unexpected operational issues relating to the abrasive nature of lunar dust, such as scratched visors and spacesuit pressure seal leaks, were encountered during the Apollo missions. To avoid reoccurrence of these unexpected detrimental equipment problems on future missions to the Moon, a series of two- and three-body abrasion tests were developed and conducted in order to begin rigorously characterizing the effect of lunar dust abrasiveness on candidate surface system materials. Two-body scratch tests were initially performed to examine fundamental interactions of a single particle on a flat surface. These simple and robust tests were used to establish standardized measurement techniques for quantifying controlled volumetric wear. Subsequent efforts described in the paper involved three-body abrasion testing designed to be more representative of actual lunar interactions. For these tests, a new tribotester was developed to expose samples to a variety of industrial abrasives and lunar simulants. The work discussed in this paper describes the three-body hardware setup consisting of a rotating rubber wheel that applies a load on a specimen as a loose abrasive is fed into the system. The test methodology is based on ASTM International (ASTM) B611, except it does not mix water with the abrasive. All tests were run under identical conditions. Abraded material specimens included poly(methyl methacrylate) (PMMA), hardened 1045 steel, 6061-T6 aluminum (Al) and 1018 steel. Abrasives included lunar mare simulant JSC- 1A-F (nominal size distribution), sieved JSC-1A-F (<25 m particle diameter), lunar highland simulant NU-LHT-2M, alumina (average diameter of 50 m used per ASTM G76), and silica (50/70 mesh used per ASTM G65). The measured mass loss from each specimen was converted using standard densities to determine total wear volume in cm3. Abrasion was dominated by the alumina and the simulants were only similar to the silica (i.e., sand) on the softer materials of

  10. Liquid abrasive pressure pot scoping tests report

    SciTech Connect

    Archibald, K.E.

    1996-01-01

    The primary initiatives of the LITCO Decontamination Development group at the Idaho Chemical Process Plant (ICPP) are the development of methods to eliminate the use of sodium bearing decontamination chemicals and minimization of the amount of secondary waste generated during decontamination activities. In July of 1994, a Commerce Business Daily (CBD) announcement was issued by the INEL to determine commercial interest in the development of an in-situ liquid abrasive grit blasting system. As a result of the CBD announcement, Klieber & Schulz issued an Expression of Interest letter which stated they would be interested in testing a prototype Liquid Abrasive Pressure Pot (LAPP). LITCO`s Decontamination group and Kleiber & Schulz entered into a Cooperative Research and Development Agreement (CRADA) in which the Decontamination Development group tested the prototype LAPP in a non-radioactive hot cell mockup. Test results are provided.

  11. Design of an impact abrasion testing machine

    NASA Astrophysics Data System (ADS)

    Zhang, D.; Beeley, P. R.; Baker, A. J.

    1994-04-01

    By using a cam-flat follower-impact shaft with a crank-flat rotating anvil system, the machine to be described can create various impact abrasion conditions to simulate a large range of industrial situations encountered in this field. The main features of the machine are the long working life of the flat rotating anvil, which works in the same way as that of the disk in a pin-on-disk wear tester, and the accurate control of both the impact energy delivered to the specimen and the total sliding distance of the specimen on the anvil. Statistical analysis of test results on the machine with EN24 steel and cast high manganese steel shows that the uncertainty of the population mean is within +/- 4.7% of the sample mean under a 95% confidence level of student distribution, which indicates a very good accuracy of test.

  12. New Rock Abrasivity Test Method for Tool Life Assessments on Hard Rock Tunnel Boring: The Rolling Indentation Abrasion Test (RIAT)

    NASA Astrophysics Data System (ADS)

    Macias, F. J.; Dahl, F.; Bruland, A.

    2016-05-01

    The tunnel boring machine (TBM) method has become widely used and is currently an important presence within the tunnelling industry. Large investments and high geological risk are involved using TBMs, and disc cutter consumption has a great influence on performance and cost, especially in hard rock conditions. Furthermore, reliable cutter life assessments facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory tests for rock abrasivity assessments are needed. A new abrasivity test method by rolling disc named Rolling Indentation Abrasion Test (RIAT) has been developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than the traditionally used methods. Wear by rolling contact on intact rock samples is introduced and several rock types, covering a wide rock abrasiveness range, have been tested by RIAT. The RIAT procedure indicates a great ability of the testing method to assess abrasive wear on rolling discs. In addition and to evaluate the newly developed RIAT test method, a comprehensive laboratory testing programme including the most commonly used abrasivity test methods and the mineral composition were carried out. Relationships between the achieved results from conventional testing and RIAT results have been analysed.

  13. Mars Pathfinder Wheel Abrasion Experiment Ground Test

    NASA Technical Reports Server (NTRS)

    Keith, Theo G., Jr.; Siebert, Mark W.

    1998-01-01

    The National Aeronautics and Space Administration (NASA) sent a mission to the martian surface, called Mars Pathfinder. The mission payload consisted of a lander and a rover. The primary purpose of the mission was demonstrating a novel entry, descent, and landing method that included a heat shield, a parachute, rockets, and a cocoon of giant air bags. Once on the surface, the spacecraft returned temperature measurements near the Martian surface, atmosphere pressure, wind speed measurements, and images from the lander and rover. The rover obtained 16 elemental measurements of rocks and soils, performed soil-mechanics, atmospheric sedimentation measurements, and soil abrasiveness measurements.

  14. The wear of oriented UHMWPE under isotropically rough and scratched counterface test conditions.

    PubMed

    Dharmastiti, R; Barton, D C; Fisher, J; Edidin, A; Kurtz, S

    2001-01-01

    Unidirectional wear tests of UHMWPE against smooth counterfaces show that molecular chains at the surface of virgin material become oriented parallel to the sliding direction giving low wear rate. It is postulated that under more abrasive conditions and predominantly unidirectional motion as in knee prostheses, it may proof beneficial to provide molecular orientation of the bulk material. Therefore strips of UHMWPE were oriented by die drawing at elevated temperature and the resulting anisotropic material subjected to tensile tests, small punch tests and also unidirectional wear tests both parallel and perpendicular to the draw direction. The tensile tests showed that, in the parallel direction, the oriented UHMWPE became stiffer and less ductile compared to the virgin UHMWPE. In the perpendicular direction, there were reductions in yield stress, 5% proof stress and energy to failure compared to the virgin material. The small punch test showed that the oriented UHMWPE exhibited apparent hardening when tested in both parallel and perpendicular directions but the mechanical behaviour in the perpendicular direction was comparable to the virgin UHMWPE. The wear tests demonstrated that the oriented UHMWPE did not show any significant improvement of wear resistance for sliding against either isotropically rough or scratched counterfaces. There was no clear dependency between the mechanical properties and wear factors of the oriented UHMWPE. PMID:11564907

  15. Adhesion scratch testing - A round-robin experiment

    NASA Technical Reports Server (NTRS)

    Perry, A. J.; Valli, J.; Steinmann, P. A.

    1988-01-01

    Six sets of samples, TiN coated by chemical or physical vapor deposition methods (CVD or PVD) onto cemented carbide or high-speed steel (HSS), and TiC coated by CVD onto cemented carbide have been scratch tested using three types of commercially available scratch adhesion tester. With exception of one cemented carbide set, the reproducibility of the critical loads for any given set with a given stylus is excellent, about + or - 5 percent, and is about + or - 20 percent for different styli. Any differences in critical loads recorded for any given sample set can be attributed to the condition of the stylus (clean, new, etc.), the instrument used, the stylus itself (friction coefficient, etc.), and the sample set itself. One CVD set showed remarkably large differences in critical loads for different styli, which is thought to be related to a mechanical interaction between stylus and coating which is enhanced by a plastic deformability in the film related to the coating microstructure. The critical load for TiN on HSS increases with coating thickness, and differences in frictional conditions led to a systematic variation in the critical loads depending on the stylus used.

  16. A modified ASTM G-75 abrasion test helps select candidate alloys for service in a corrosive and abrasive slurry

    SciTech Connect

    Corbett, R.A.; Morrison, W.S.; Jenkins, C.F.; Westinghouse Savannah River Co., Aiken, SC )

    1989-01-01

    The design of a hazardous waste immobilization facility at the Savannah River Site (SRS) set material requirements for both abrasion resistance and corrosion resistance in process equipment. Standard ASTM slurry wear test G75 was modified to permit evaluation and comparison of abrasive resistance of candidate materials of construction in the laboratory. However, corrosion was found to contribute significantly to overall metal loss during the testing. Consequently, the abrasive slurry used for the testing was modified by adjusting its chemistry to include appropriate corrosive species. The Miller numbers obtained in the modified G75 Miller abrasion test are described. Pilot plant observations for Type 304L austenitic stainless steel were available. These data were used to generate a Morrison-Miller Ratio'' in order to determine anticipated field abrasion properties for other alloys. Hardness for many of the alloys fell in a narrow range about Rockwell B90, but performance varied significantly in response to slurry chemistry. This effect if synergistic may often be overlooked in the selection process, and it needs to be addressed. Some pilot plant testing of other alloys is essential to confirm the calculated abrasion rates and the approach of using the Morrison-Miller ratio. 6 refs., 3 figs., 5 tabs.

  17. Abrasion Testing of Critical Components of Hydrokinetic Devices

    SciTech Connect

    Worthington, Monty; Ali, Muhammad; Ravens, Tom

    2013-12-06

    The objective of the Abrasion Testing of Critical Components of Hydrokinetic Devices (Project) was to test critical components of hydrokinetic devices in waters with high levels of suspended sediment – information that is widely applicable to the hydrokinetic industry. Tidal and river sites in Alaska typically have high suspended sediment concentrations. High suspended sediment also occurs in major rivers and estuaries throughout the world and throughout high latitude locations where glacial inputs introduce silt into water bodies. In assessing the vulnerability of technology components to sediment induced abrasion, one of the greatest concerns is the impact that the sediment may have on device components such as bearings and seals, failures of which could lead to both efficiency loss and catastrophic system failures.

  18. Evaluation of the scratch collapse test for the diagnosis of carpal tunnel syndrome.

    PubMed

    Makanji, H S; Becker, S J E; Mudgal, C S; Jupiter, J B; Ring, D

    2014-02-01

    This prospective study measured and compared the diagnostic performance characteristics of various clinical signs and physical examination manoeuvres for carpal tunnel syndrome (CTS), including the scratch collapse test. Eighty-eight adult patients that were prescribed electrophysiological testing to diagnose CTS were enrolled in the study. Attending surgeons documented symptoms and results of standard clinical manoeuvres. The scratch collapse test had a sensitivity of 31%, which was significantly lower than the sensitivity of Phalen's test (67%), Durkan's test (77%), Tinel's test (43%), CTS-6 lax (88%), and CTS-6 stringent (54%). The scratch test had a specificity of 61%, which was significantly lower than the specificity of thenar atrophy (96%) and significantly higher than the specificity of Durkan's test (18%) and CTS-6 lax (13%). The sensitivity of the scratch collapse test was not superior to other clinical signs and physical examination manoeuvers for CTS, and the specificity of the scratch collapse test was superior to that of Durkan's test and CTS-6 lax. Further studies should seek to limit the influence of a patient's clinical presentation on scratch test performance and assess the scratch test's inter-rater reliability. PMID:23855039

  19. On the combined use of scratch tests and CLA profilometry for the characterization of polyester powder coatings: Influence of scratch load and speed

    NASA Astrophysics Data System (ADS)

    Barletta, M.; Gisario, A.; Lusvarghi, L.; Bolelli, G.; Rubino, G.

    2008-09-01

    The prediction of the mechanical properties of polyester powder coatings is of paramount importance, as they have to undergo a wide variety of forces and deformations during their service life. Determine the response of polymeric coatings to the actual loading conditions can be, however, very troublesome as their properties are function of the material physical state, rate-dependence and yield and break behaviour. Further, the characterization of soft, contaminated organic surfaces such as polymers can often cause severe problems with reliability and imaging accuracy due to instrumental artefacts. This is therefore the context in which this paper investigates the capability of multiple parameters scratch tests joined with non-contact CLA profilometry and FE-SEM to detect the scratch response of polyester powder coatings for protective and decorative outdoor applications. Scratch tests with blunt contact geometry were used to evaluate the response of polyester coatings baked at different time-temperature programs and, so, at different stages of their curing process. In particular, being such coatings highly non-linear in their response to mechanical stress or strain, the influence from scratch load and speed was carefully taken into account. Analytical evaluations of the experimental results led to good correlations between the extent of the deformed zone after scratch, scratch parameters and curing operational settings. This allows mapping the scratch response of the polyester topcoats to broad ranges of both scratch parameters and curing conditions.

  20. Repassivation of 304 stainless steel investigated with a single scratch test

    SciTech Connect

    Adler, T.A.; Walters, R.R. )

    1993-05-01

    Reformation of the passive film on 304 stainless steel (UNSS 30400) was investigated with a scratch test. Regrowth of the passive film was measured by recording the current that resulted from forming the scratch. Charge consumed during the reformation of the film was compared to wear produced by the scratch. The current density from an incremental area of the scratch was extracted from the measured current transients using the width of the scratch as a function of time. The maximum current density and the charge density were dependent linearly on the area fraction of bare surface. Other parameters used in the model of current transients did not change as the area fraction of bare surface changed. Results showed the passive film remained adherent to the surface of the stainless steel during the rubbing mode of wear.

  1. The scratch test - Different critical load determination techniques. [adhesive strength of thin hard coatings

    NASA Technical Reports Server (NTRS)

    Sekler, J.; Hintermann, H. E.; Steinmann, P. A.

    1988-01-01

    Different critical load determination techniques such as microscopy, acoustic emission, normal, tangential, and lateral forces used for scratch test evaluation of complex or multilayer coatings are investigated. The applicability of the scratch test to newly developed coating techniques, systems, and applications is discussed. Among the methods based on the use of a physical measurement, acoustic emission detection is the most effective. The dynamics ratio between the signals below and above the critical load for the acoustic emission (much greater than 100) is well above that obtained with the normal, tangential, and lateral forces. The present commercial instruments are limited in load application performance. A scratch tester able to apply accurate loads as low as 0.01 N would probably overcome most of the actual limitations and would be expected to extend the scratch testing technique to different application fields such as optics and microelectronics.

  2. EFFECT OF GRAIN SIZE ON DYNAMIC SCRATCH RESPONSE IN ALUMINA

    SciTech Connect

    Wang, Hong; Wereszczak, Andrew A; Lance, Michael J

    2006-01-01

    The machining and wear of ceramics and ceramic components are obviously influenced by abrasive damage. One parameter that can affect the abrasion process is the grain size of the ceramic material. To investigate this, single-grit pendulum scratch testing was used to investigate the dynamic scratch response in three 99.9% aluminas that each had a tight size distribution about mean grain sizes of 2, 15, or 25 m, respectively. The scratch speeds generated had an order of magnitude of ~ 1 m/s and the maximum scratch depths were several tens of micrometers. Tangential and normal scratch forces were monitored during each test and interpreted in conjunction with postmortem SEM and profilometry results. It was observed that both plastic deformation and brittle fracture participated in the scratching process and the relative activity of each was dependent on depth of penetration. At a specific depth of penetration, the material removal of alumina prevailingly relies on the generation and interaction of oblique radial and lateral cracks. Chip formation is greatly enhanced when the created cracks interact and that interaction itself depends on grain size. Larger grain size gives rise to larger lateral cracks, more severe fracture at the groove's bottom, and larger amplitude of scratch force oscillation. Lastly, the cutting pressure and the scratch hardness of alumina exhibit sensitivity to both grain size and the groove depth.

  3. Diagnosis of carpal tunnel syndrome: interobserver reliability of the blinded scratch-collapse test.

    PubMed

    Blok, Robin D; Becker, Stéphanie J E; Ring, David C

    2014-06-01

    The reliability of the scratch-collapse test for diagnosis of carpal tunnel syndrome (CTS) has not been tested by independent investigators. This study measured the reliability of the scratch-collapse test comparing the treating hand surgeon and blinded evaluators. We performed a prospective observational study of 41 patients with a provisional diagnosis of CTS or a combination of CTS and cubital tunnel syndrome and prescribed electrodiagnostic testing. The treating hand surgeon performed the scratch-collapse test. Next, the test was administered by one of the six observers, unaware of the patient's symptoms and the diagnosis made by treating hand surgeon. The kappa statistic (κ) was used to calculate the interrater reliability between the treating hand surgeons and blinded scratchers. The agreement between the blinded observers and the hand surgeons on the scratch-collapse test was substantial 0.63 (95 % CI, 0.34-0.87; p < 0.001). The sensitivity of the blinded scratch test in our sample was 32 %. In a small study with a spectrum bias favoring electrophysiologically confirmed CTS the reliability was lower than that reported by the inventors of the test, but was still substantial. We propose a larger study of patients with a greater variety of electrodiagnostic test results using fewer observers with more experience. PMID:24876682

  4. Fatigue Testing of Abrasive Water Jet Cut Titanium

    SciTech Connect

    Hovanski, Yuri; Dahl, Michael E.; Williford, Ralph E.

    2009-06-08

    Battelle Memorial Institute as part of its U.S. Department of Energy (USDOE) Contract No. DE-AC05-76RL01830 to operate the Pacific Northwest National Laboratory (PNNL) provides technology assistance to qualifying small businesses in association with a Technology Assistance Program (TAP). Qualifying companies are eligible to receive a set quantity of labor associated with specific technical assistance. Having applied for a TAP agreement to assist with fatigue characterization of Abrasive Water Jet (AWJ) cut titanium specimens, the OMAX Corporation was awarded TAP agreement 09-02. This program was specified to cover dynamic testing and analysis of fatigue specimens cut from titanium alloy Ti-6%Al-4%V via AWJ technologies. In association with the TAP agreement, a best effort agreement was made to characterize fatigue specimens based on test conditions supplied by OMAX.

  5. Scratch behaviors in polymers

    NASA Astrophysics Data System (ADS)

    Xiang, Chen

    2000-10-01

    As part of a large effort toward the fundamental understanding of scratch behaviors in polymeric materials, studies were carried out on a broad range of polymers, with an emphasis on automotive thermoplastic olefins (TPOs). Two types of scratch tests were performed in this research, i.e., Ford constant load and instrumented progressive load scratch tests. A scratch model proposed by Hamilton and Goodman was applied to understand the fundamental mechanics of the scratch process. Several characterization techniques were used to investigate the scratch damage mechanisms in polymers. Both testing results and the scratch model analysis indicate that certain rigidity in polymers is essential to give good scratch resistance. Fundamental understanding of the scratching process in terms of basic material characteristics such as Young's modulus, yield stress, tensile strength, friction coefficient, scratch hardness, penetration recovery and fracture toughness are discussed. Scratch damage investigation, on both surface and subsurface, shows that shear yielding is the main cause of the plastics flow scratch pattern, while tensile tear on the surface and shear induced fracture on the subsurface are the main damage mechanisms in the fracture scratch pattern. This study explains why automotive TPOs are susceptible to scratch under the current scratch test practiced in automotive industry. Shear deformation and fracture behavior in model TPOs are also studied using the Iosipescu shear test. Iosipescu shear deformation in terms of shear stress-strain curves of model TPOs is obtained experimentally. Shear fracture process and damage mechanisms in TPOs are also demonstrated and revealed. Further studies on the scratch damage in TPOs based on the roles of additives and fillers in the scratch behavior are addressed. The effects of phase morphology and toughening mechanisms on scratch behavior in TPOs are also discussed. This research has resulted in an increased understanding of the

  6. Screen Cage Ion Plating (SCIP) and scratch testing of polycrystalline aluminum oxide

    NASA Technical Reports Server (NTRS)

    Spalvins, Talivaldis; Sliney, Harold E.; Deadmore, Daniel L.

    1992-01-01

    A screen cage ion plating (SCIP) technique was developed to apply silver films on electrically nonconducting aluminum oxide. It is shown that SCIP has remarkable throwing power; surfaces to be coated need not be in direct line of sight with the evaporation source. Scratch tests, employing a diamond stylus with a 200 micro m radius tip, were performed on uncoated and on silver coated alumina. Subsequent surface analysis show that a significant amount of silver remains on the scratched surfaces, even in areas where high stylus load produced severe crack patterns in the ceramic. Friction coefficients were lowered during the scratch tests on the coated alumina indicating that this modification of the ion planting process should be useful for applying lubricating films of soft metals to electrical insulating materials. The very good throwing power of SCIP also strongly suggests general applicability of this process in other areas of technology, e.g., electronics, in addition to tribology.

  7. Relationship between Los Angeles attrition test and Nordic abrasion test of volcanic rocks

    NASA Astrophysics Data System (ADS)

    Krutilová, Kateřina; Prikryl, Richard

    2015-04-01

    Various volcanic rocks contribute significantly to the production of crushed stone in the Czech Republic. When used for road surfacing, results of Los Angeles attrition test (LA value below 25 or 30 depending on the mode of use) together with polished stone value are required. In the recent study, we have focused on the search for possible correlation between results obtained by Los Angeles attrition test and Nordic abrasion test, a test widely employed in Scandinavia. For the experimental study, a set of volcanic rocks from 36 active quarries was used. The rocks under study represent range of volcanic rocks from ultrabasic to acid members, formed form Neoproterozoic to Tertiary. The most favourable results of Los Angeles attrition test (i.e. the lowest LA values) were obtained for basalts (range of values 9.4-19.4) and spilites (range of values 8.4-14.9) which are in fact Neoproterozoic to Late Palaeozoic basalts affected by low grade metamorphism. Nordic abrasion test exhibited much broader range of values (6.4 to 36.9) with average value at 15.2 for basalts, resulting in weak coefficient of determination (0.19). . On contrary, narrow range of values from Nordic abrasion test of spilites (7.2-15.9), very similar to the range of LA values, is reflect in higher coefficient of determination (0.56). On contrary, the least favourable properties (LA values 12.3-29.2, Nordic abrasion 16.8-43.3) have been observed for a group of basic to intermediate rocks classified in older literature as melaphyres and diabases (ranging from basalts to trachyndesites and/or trachybasalts) of Palaeozoic age. However, in this specific group of volcanic rocks, the highest coefficient of determination (0.89) between both tests has been achieved. For volcanic rocks exhibiting acid composition (rhyolites and quartz porphyry), coefficient of determination between LA values (15.1-19.3) and Nordic abrasion test (7.3-21.9) is weak (0.42). The weakest relationship between LA values (14

  8. Development and Testing of Abrasion Resistant Hard Coats For Polymer Film Reflectors: Preprint

    SciTech Connect

    Jorgensen, G.; Gee, R.; DiGrazia, M.

    2010-10-01

    Reflective polymer film technology can significantly reduce the cost of solar reflectors and installed Concentrated Solar Power (CSP) plants by both reduced material cost and lower weight. One challenge of polymer reflectors in the CSP environment pertains to contact cleaning methods typically used with glass mirrors. Such contact cleaning methods can scratch the surface of polymer reflectors and thereby reduce specular reflectance. ReflecTech, Inc. (a subsidiary of SkyFuel, Inc.) and the National Renewable Energy Laboratory (NREL) initiated a cooperative research and development agreement (CRADA) to devise and develop an abrasion resistant coating (ARC) suitable for deposition onto polymer based mirror film. A number of candidate ARC products were identified as candidate formulations. Industrial collaborators prepared samples having their ARCs deposited onto ReflecTech Mirror Film pre-laminated to aluminum sheet substrates. Samples were provided for evaluation and subjected to baseline (unweathered) and accelerated exposure conditions and subsequently characterized for abrasion resistance and adhesion. An advanced ARC product has been identified that exhibits outstanding initial abrasion resistance and adhesion to ReflecTech Mirror Film. These properties were also retained after exposure to the various accelerated stress conditions. This material has been successfully manufactured as a 1.5 m wide roll-to-roll construction in a production environment.

  9. A correlation between abrasion resistance and other properties of some acrylic resins used in dentistry.

    PubMed

    Harrison, A; Huggett, R; Handley, R W

    1979-01-01

    This investigation studies the relationship of hardness, elastic modulus and scratch width as dependent variables to the abrasion resistance of twenty-three dental acrylic resins. The multiple correlation R, when all three variables are used as predictors, is 0.727. Because of the significant intercorrelations between the variables themselves a stepwise multiple regression analysis showed hardness as a redundant variable. Abrasive wear can be estimated from the following equation Abrasive wear = 806.1 - 0.1498 modulus + 0.681 scratch width (R = 0.725; standard deviation of estimate +/- 50.8) The deletion of scratch width does not appreciably reduce the standard deviation of the estimate: Abrasive wear = 1063.4 - 0.2055 modulus (r = 0.683; standard deviation of estimate +/- 50.3) The method of curing the specimens conformed to the respective manufacturers' instructions. Abrasion and scratch tests were performed using methods developed by the authors and previously described in the literature, whereas the hardness and elastic modulus results were devised from standard test procedures. Further research is currently in progress to improve the predictive power of abrasion resistance with additional new variables. PMID:429382

  10. Abrasion Testing of Candidate Outer Layer Fabrics for Lunar EVA Space Suits

    NASA Technical Reports Server (NTRS)

    Mitchell, Kathryn C.

    2010-01-01

    During the Apollo program, the space suit outer layer fabrics were badly abraded after just a few Extravehicular Activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots, which penetrated the outer layer fabric into the thermal protection layers after less than eight hours of surface operations. Current plans for the Constellation Space Suit Element require the space suits to support hundreds of hours of EVA on the Lunar surface, creating a challenge for space suit designers to utilize materials advances made over the last forty years and improve upon the space suit fabrics used in the Apollo program. A test methodology has been developed by the NASA Johnson Space Center Crew and Thermal Systems Division for establishing comparative abrasion wear characteristics between various candidate space suit outer layer fabrics. The abrasion test method incorporates a large rotary drum tumbler with rocks and loose lunar simulant material to induce abrasion in fabric test cylinder elements, representative of what might occur during long term planetary surface EVAs. Preliminary materials screening activities were conducted to determine the degree of wear on representative space suit outer layer materials and the corresponding dust permeation encountered between subsequent sub -layers of thermal protective materials when exposed to a simulated worst case eight hour EVA. The test method was used to provide a preliminary evaluation of four candidate outer layer fabrics for future planetary surface space suit applications. This Paper provides a review of previous abrasion studies on space suit fabrics, details the methodologies used for abrasion testing in this particular study, and shares the results and conclusions of the testing.

  11. Abrasion Testing of Candidate Outer Layer Fabrics for Lunar EVA Space Suits

    NASA Technical Reports Server (NTRS)

    Mitchell, Kathryn

    2009-01-01

    During the Apollo program, the space suit outer layer fabrics were severely abraded after just a few Extravehicular Activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots, which penetrated the outer layer fabric into the thermal protection layers after less than eight hours of surface operations. Current plans for the Constellation Space Suit Element require the space suits to support hundreds of hours of EVA on the Lunar surface, creating a challenge for space suit designers to utilize materials advances made over the last forty years and improve upon the space suit fabrics used in the Apollo program. A test methodology has been developed by the NASA Johnson Space Center Crew and Thermal Systems Division for establishing comparative abrasion wear characteristics between various candidate space suit outer layer fabrics. The abrasion test method incorporates a large rotary drum tumbler with rocks and loose lunar simulant material to induce abrasion in fabric test cylinder elements, representative of what might occur during long term planetary surface EVAs. Preliminary materials screening activities were conducted to determine the degree of wear on representative space suit outer layer materials and the corresponding dust permeation encountered between subsequent sub-layers of thermal protective materials when exposed to a simulated worst case eight hour EVA. The test method was used to provide a preliminary evaluation of four candidate outer layer fabrics for future planetary surface space suit applications. This paper provides a review of previous abrasion studies on space suit fabrics, details the methodologies used for abrasion testing in this particular study, shares the results of the testing, and provides recommendations for future work.

  12. Considerations on the European Standard EN 14157 Test Methods: Abrasion Resistance of Natural Stones Used for Flooring in Buildings

    NASA Astrophysics Data System (ADS)

    Karaca, Z.; Günes Yılmaz, N.; Goktan, R. M.

    2012-01-01

    In Europe, the Wide Wheel abrasion (WWA) test and the Böhme abrasion (BA) test are among the most widely used standard test methods for determining abrasion resistance of natural stones, the former being the reference test method in EN 14157 Standard. However, it is stated in the Annex-A (Informative) of EN 14157 Standard that very limited data are available to provide correlations between these two test methods. To be able to fill this gap, in this study, 25 different natural stones belonging to sedimentary, metamorphic and igneous groups were tested for their abrasion resistance as well as physico-mechanical properties. Also, for a better interpretation of abrasion resistance characteristics of the tested stone materials, relationships between abrasion resistance and physico-mechanical properties were statistically examined. A statistically significant linear correlation ( R 2 = 0.85; P value = 0.000) was established between the WWA test and the BA test, which could be used in practice for converting the measured abrasion resistance values from one testing method to another. It was also found that the correlation between these two test methods improved significantly ( R 2 = 0.93; P value = 0.001) when relatively high-porosity stone materials (porosity ≥1%) were separately evaluated. Both methods of abrasion resistance employed in the present study showed statistically significant linear correlations with uniaxial compressive strength and Brazilian tensile strength, the former proving to be a more influencing parameter on resistance to abrasion. Also, from the point view of representing actual abrasion mechanism of stone materials in practice, the necessity of simulating multi-directional foot traffic in abrasion testing methods was discussed. In this respect, the reference test method in the EN 14157 Standard was criticized for not fully meeting this requirement. It was also pointed out that the reference method could have some drawbacks when applied to coarse

  13. 16 CFR Figure 8 to Part 1512 - Reflectorized Bicycle Wheel Rim Abrasion Test Device

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Reflectorized Bicycle Wheel Rim Abrasion Test Device 8 Figure 8 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Fig. 8 Figure 8 to Part...

  14. 16 CFR Figure 8 to Part 1512 - Reflectorized Bicycle Wheel Rim Abrasion Test Device

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Reflectorized Bicycle Wheel Rim Abrasion Test Device 8 Figure 8 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Fig. 8 Figure 8 to Part...

  15. 16 CFR Figure 8 to Part 1512 - Reflectorized Bicycle Wheel Rim Abrasion Test Device

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Reflectorized Bicycle Wheel Rim Abrasion Test Device 8 Figure 8 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Fig. 8 Figure 8 to Part...

  16. 16 CFR Figure 8 to Part 1512 - Reflectorized Bicycle Wheel Rim Abrasion Test Device

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Reflectorized Bicycle Wheel Rim Abrasion Test Device 8 Figure 8 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Fig. 8 Figure 8 to Part...

  17. 16 CFR Figure 8 to Part 1512 - Reflectorized Bicycle Wheel Rim Abrasion Test Device

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Reflectorized Bicycle Wheel Rim Abrasion Test Device 8 Figure 8 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Fig. 8 Figure 8 to Part...

  18. Abrasion and erosion testing of materials used in power production from coal

    SciTech Connect

    Tylczak, Joseph H.; Adler, Thomas A.; Rawers, James C.

    2003-09-01

    The Albany Research Center (ARC) has a long history of studying abrasive wear, related to mineral testing, handling, and processing. The center has also been instrumental in the design and development of wear test procedures and equipment. Research capabilities at ARC include Pin-on-Drum, Pin-on-Disk, and Dry Sand/Rubber Wheel abrasion tests, Jaw Crusher gouging test, Ball-on-Ball Impact test, and Jet erosion tests. Abrasive and erosive wear studies have been used to develop both new alloys and improved heat treatments of commercial alloys. As part of ARC’s newest iteration on wear testing to evaluate materials for use in new and existing pulverized coal combustion and gasifier power systems, the ARC has designed and constructed a new High Temperature Hostile Atmosphere Erosion Wear Test (HAET). This new piece of test apparatus is designed for erosive particle velocities of 10-40 m/sec and temperatures from room temperature (23°C) to 800+°C, with special control over the gas atmosphere. A variable speed whirling arm design is used to vary the impact energy of the gravity fed erosive particles. The specimens are mounted at the edge of a disk and allow a full range of impingement angles to be selected. An electric furnace heats the specimens in an enclosed retort to the selected temperature. Tests include both oxidizing conditions and reducing conditions. A range of gases, including CO, CO2, CH4, H2, H2S, HCl, N2, O2, and SO2 can be mixed and delivered to the retort. During the erosion testing a stream of abrasive powder is delivered in front of the specimens. This apparatus is designed to use low abrasive fluxes, which simulate real operating conditions in commercial power plants. Currently ~270 μm SiO2 particles are being used to simulate the abrasive impurities typically found in coal. Since operators are always striving for longer lifetimes and higher operating temperatures, this apparatus can help elucidate mechanisms of wastage and identify superior

  19. Development of a two-body wet abrasion test method with attention to the effects of reused abradant

    SciTech Connect

    Blau, Peter Julian; Dehoff, Ryan R

    2012-01-01

    Abrasive wear is among the most common and costliest causes for material wastage, and it occurs in many forms. A simple method has been developed to quantify the response of metals and alloys to two-body wet abrasion. A metallographic polishing machine was modified to create a disk-on-flat sliding test rig. Adhesive-backed SiC grinding papers were used under fixed load and speed to rank the abrasive wear of seven alloy steels, some of which are candidates for drill cones for geothermal drilling. Standardized two-body abrasion tests, like those described in ASTM G132, feed unused abrasive into the contact; however, the current work investigated whether useful rankings could still be obtained with a simpler testing configuration in which specimens repeatedly slide on the same wear path under water-lubricated conditions. Tests using abrasive grit sizes of 120 and 180 resulted in the same relative ranking of the alloys although the coarser grit produced more total wear. Wear decreased when the same abrasive disk was re-used for up to five runs, but the relative rankings of the steels remained the same. This procedure was presented to ASTM Committee G2 on Wear and Erosion as a potential standard test for wet two-body abrasive wear.

  20. An energetic approach to abrasive wear of a martensitic stainless steel

    SciTech Connect

    Pamuk, U.; Baydogan, M.; Niluefer, B.; Cimenoglu, H.

    2000-04-01

    Abrasive wear is the most common type of wear that causes failure of machine elements. Examinations of abraded surfaces revealed presence of embedded particles and grooves elongated along the sliding direction. This indicates that, there are two sequential stages of an abrasion process. In the first stage, asperities on the hard surface and/or hard abrasive grains penetrate into the soft material surface and then in the second stage, they grind the surface in the sliding direction. Therefore, indentation and scratching of an indenter, which can be realized by hardness and scratch tests, can simulate the damage produced on the abraded surface. On the basis of this simulation, an energetic model is proposed for abrasive wear in the present study. In this study, abrasive wear behavior of a martensitic stainless steel is examined by hardness and scratch tests. The results of tests were evaluated to estimate the work done during abrasion and to find out the dimensional wear coefficient according to the model proposed above.

  1. Evaluation of weight loss and surface roughness of compomers after simulated toothbrushing abrasion test.

    PubMed

    Mondelli, Rafael Francisco Lia; Wang, Linda; Garcia, Fernanda Cristina Pimentel; Prakki, Anuradha; Mondelli, José; Franco, Eduardo Batista; Ishikiriama, Aquira

    2005-06-01

    This study aimed at analyzing the compomers wear by an "in vitro" toothbrushing abrasion test. The null hypotheses tested were that there would be no differences in weight loss and no significant changes in surface roughness of the compomers after this test. The utilized commercial brands were Dyract (Dentsply), Dyract AP (Dentsply), Compoglass F (Vivadent), Freedom (SDI), F2000 (3M ESPE), which were compared to the two resin composites Z100 (3M ESPE) and Silux Plus (3M ESPE). Ten cylindrical specimens for each commercial brand were prepared with 5mm diameter and 3mm thickness. An appropriate machine with soft bristle tips containing dentifrice solution and deionized water was used. A total of 100,000 brushing cycles were performed. The amount of weight loss was measured by the percentage alteration between the initial (before toothbrushing) and final weight (after toothbrushing), measured by a Sartorius analytical balance. The surface roughness change was determined by the percentage difference between initial and final means after 5 tracings by a T 1000 Hommel Tester roughness meter on the specimen's surfaces before and after toothbrushing abrasion test. The statistical analysis (Students paired t-test, ANOVA and Tukey, á=0.05) showed that all materials presented statistically significant weight loss and roughness increase after abrasion test. All compomers presented higher weight loss than resin composites. Freedom and Dyract AP presented the lowest weight loss among compomers. F2000 presented the worst abrasion resistance, without statistical differences with Dyract. For roughness changes, Dyract, Dyract AP, Z100, Compoglass F and Silux Plus showed the lowest surface roughness alteration, in increasing order, without statistical differences between them. Freedom was the statistically roughest material of the study. PMID:20924536

  2. Use of Acoustic Emission During Scratch Testing for Understanding Adhesion Behavior of Aluminum Nitride Coatings

    NASA Astrophysics Data System (ADS)

    Choudhary, R. K.; Mishra, P.

    2016-04-01

    In this work, acoustic emission during scratch testing of the aluminum nitride coatings formed on stainless steel substrate by reactive magnetron sputtering was analyzed to assess the coating failure. The AlN coatings were formed under the variation of substrate temperature, substrate bias potential, and discharge power. The coatings deposited in the temperature range of 100 to 400 °C showed peak acoustic emission less than 1.5%, indicating ductile nature of the coating. However, for coatings formed with substrate negative bias potential of 20 to 50 V, numerous sharp acoustic bursts with maximum emission approaching 80% were observed, indicating brittle nature of the coatings with large number of defects present. The shift in the intensity of the first major acoustic peak toward higher load, with the increasing bias potential, confirmed improved adhesion of the coating. Also, the higher discharge power resulted in increased acoustic emission.

  3. Use of Acoustic Emission During Scratch Testing for Understanding Adhesion Behavior of Aluminum Nitride Coatings

    NASA Astrophysics Data System (ADS)

    Choudhary, R. K.; Mishra, P.

    2016-06-01

    In this work, acoustic emission during scratch testing of the aluminum nitride coatings formed on stainless steel substrate by reactive magnetron sputtering was analyzed to assess the coating failure. The AlN coatings were formed under the variation of substrate temperature, substrate bias potential, and discharge power. The coatings deposited in the temperature range of 100 to 400 °C showed peak acoustic emission less than 1.5%, indicating ductile nature of the coating. However, for coatings formed with substrate negative bias potential of 20 to 50 V, numerous sharp acoustic bursts with maximum emission approaching 80% were observed, indicating brittle nature of the coatings with large number of defects present. The shift in the intensity of the first major acoustic peak toward higher load, with the increasing bias potential, confirmed improved adhesion of the coating. Also, the higher discharge power resulted in increased acoustic emission.

  4. Wear of combinations of acrylic resin and porcelain, on an abrasion testing machine.

    PubMed

    Harrison, A

    1978-04-01

    Wear tests of various combinations of acrylic resin and porcelain were made using a machine which was designed to test materials under conditions similar to those of masticatory function by simulating the loads, sliding distances, and contact times encountered in the human masticatory cycle. The results showed that the amount of wear of the two materials worn in combination depended on the nature of the surrounding medium and on the surface roughness of the opposing material. Acrylic resin showed good wear resistance provided no third party abrasive or opposing hard, rough surface was present. When a mild abrasive was incorporated in the system, the acrylic resin vs acrylic resin combination wore almost seven times more than porcelain vs porcelain. Clinical experience would suggest that this is a reasonably sound order of wear. PMID:213546

  5. Microstructural effects in abrasive wear. Third annual progress report, August 12, 1983-August 14, 1984

    SciTech Connect

    Kosel, T.H.

    1984-08-14

    The two major goals of the project are to improve our understanding of the mechanisms of carbide removal and of the role of matrix properties in abrasion. In the area of carbide removal mechanisms, progress this year has included completion of the fixed-depth scratch test apparatus and its use to demonstrate the occurrence of gross carbide cracking under fixed-depth conditions; comparable cracking does not occur under fixed-load conditions at a similar mean load. A high-stress abrasion system has been constructed and tested which will facilitate studies of abrasion under conditions similar to those produced by the fixed-depth scratch test system. Analysis of the work on the size effect in abrasion of dual-phase alloys has been completed. The largest single item in this year's proposed work in a study of the abrasion resistance and mechanisms of material removal in model alloys having second-phase particles (SPP's) with varying fracture properties. In the area of the effects of matrix properties on abrasion, the majority of the effort this year has centered on transmission electron microscopy of the subsurface deformation microstructures developed during abrasion.

  6. Scratch Forensics

    SciTech Connect

    Suratwala, T I; Miller, P E; Feit, M D; Menapace, J A

    2008-07-09

    Scratches on optical components which are formed during fabrication, cleaning, handling and end-use, are widespread and almost always detrimental. The impact of scratches on the end-use of the optic includes increased optical scatter, reduced system performance, and reduced strength. In the case of optics used in high intensity laser applications, prevention of scratches is paramount because they are closely associated with laser damage. Evaluation of the characteristics (dimensions, location on optic, shape, and orientation) of a scratch can serve a powerful tool to identify the cause of the scratch and lead to mitigations to prevent their reoccurrence. It is likely that opticians have used such techniques for hundreds of years. In recent years, by applying techniques of fracture mechanics and tribology, several new semi-quantitative rules-of-thumb have been developed allowing one to estimate the size and shape of the scratch inducing asperity or rogue particle, the load on the particle, the depth of the fractures in the scratch, and properties of material housing the rogue particle. The following discussion reviews some these techniques, which as a whole, we refer to as 'Scratch Forsenics'.

  7. Abrasive Wear Resistance of Tool Steels Evaluated by the Pin-on-Disc Testing

    NASA Astrophysics Data System (ADS)

    Bressan, José Divo; Schopf, Roberto Alexandre

    2011-05-01

    Present work examines tool steels abrasion wear resistance and the abrasion mechanisms which are one main contributor to failure of tooling in metal forming industry. Tooling used in cutting and metal forming processes without lubrication fails due to this type of wear. In the workshop and engineering practice, it is common to relate wear resistance as function of material hardness only. However, there are others parameters which influences wear such as: fracture toughness, type of crystalline structure and the occurrence of hard precipitate in the metallic matrix and also its nature. In the present investigation, the wear mechanisms acting in tool steels were analyzed and, by normalized tests, wear resistance performance of nine different types of tool steels were evaluated by pin-on-disc testing. Conventional tool steels commonly used in tooling such as AISI H13 and AISI A2 were compared in relation to tool steels fabricated by sintering process such as Crucible CPM 3V, CPM 9V and M4 steels. Friction and wear testing were carried out in a pin-on-disc automated equipment which pin was tool steel and the counter-face was a abrasive disc of silicon carbide. Normal load of 5 N, sliding velocity of 0.45 m/s, total sliding distance of 3000 m and room temperature were employed. The wear rate was calculated by the Archard's equation and from the plotted graphs of pin cumulated volume loss versus sliding distance. Specimens were appropriately heat treated by quenching and three tempering cycles. Percentage of alloying elements, metallographic analyses of microstructure and Vickers microhardness of specimens were performed, analyzed and correlated with wear rate. The work is concluded by the presentation of a rank of tool steel wear rate, comparing the different tool steel abrasion wear resistance: the best tool steel wear resistance evaluated was the Crucible CPM 9V steel.

  8. Air Abrasion

    MedlinePlus

    ... delivered directly to your desktop! more... What Is Air Abrasion? Article Chapters What Is Air Abrasion? What Happens? The Pros and Cons Will I Feel Anything? Is Air Abrasion for Everyone? print full article print this ...

  9. A novel two-axis load sensor designed for in situ scratch testing inside scanning electron microscopes.

    PubMed

    Huang, Hu; Zhao, Hongwei; Wu, Boda; Wan, Shunguang; Shi, Chengli

    2013-01-01

    Because of a lack of available miniaturized multiaxial load sensors to measure the normal load and the lateral load simultaneously, quantitative in situ scratch devices inside scanning electron microscopes and the transmission electron microscopes have barely been developed up to now. A novel two-axis load sensor was designed in this paper. With an I-shaped structure, the sensor has the function of measuring the lateral load and the normal load simultaneously, and at the same time it has compact dimensions. Finite element simulations were carried out to evaluate stiffness and modal characteristics. A decoupling algorithm was proposed to resolve the cross-coupling between the two-axis loads. Natural frequency of the sensor was tested. Linearity and decoupling parameters were obtained from the calibration experiments, which indicate that the sensor has good linearity and the cross-coupling between the two axes is not strong. Via the decoupling algorithm and the corresponding decoupling parameters, simultaneous measurement of the lateral load and the normal load can be realized via the developed two-axis load sensor. Preliminary applications of the load sensor for scratch testing indicate that the load sensor can work well during the scratch testing. Taking advantage of the compact structure, it has the potential ability for applications in quantitative in situ scratch testing inside SEMs. PMID:23429516

  10. Crack propagation and the material removal mechanism of glass-ceramics by the scratch test.

    PubMed

    Qiu, Zhongjun; Liu, Congcong; Wang, Haorong; Yang, Xue; Fang, Fengzhou; Tang, Junjie

    2016-12-01

    To eliminate the negative effects of surface flaws and subsurface damage of glass-ceramics on clinical effectiveness, crack propagation and the material removal mechanism of glass-ceramics were studied by single and double scratch experiments conducted using an ultra-precision machine. A self-manufactured pyramid shaped single-grit tool with a small tip radius was used as the scratch tool. The surface and subsurface crack propagations and interactions, surface morphology and material removal mechanism were investigated. The experimental results showed that the propagation of lateral cracks to the surface and the interaction between the lateral cracks and radial cracks are the two main types of material peeling, and the increase of the scratch depth increases the propagation angle of the radial cracks and the interaction between the cracks. In the case of a double scratch, the propagation of lateral cracks and radial cracks between paired scratches results in material peeling. The interaction between adjacent scratches depends on the scratch depth and separation distance. There is a critical separation distance where the normalized material removal volume reaches its peak. These findings can help reduce surface flaws and subsurface damage induced by the grinding process and improve the clinical effectiveness of glass-ceramics used as biological substitute and repair materials. PMID:27479896

  11. Determination of Shear Strength of Rocks from Scratch Tests: Theoretical Justification

    NASA Astrophysics Data System (ADS)

    Detournay, E.

    2014-12-01

    There is considerable empirical evidence that the specific energy ɛ determined from shallow scratch tests on sedimentary rocks is about equal to the uniaxial compressive strength q, see Figure showing the correlation between ɛ and q for 334 rocks (Richard et al, J Engineering Geology, 2012). The specific energy ɛ, defined as the energy expended per unit volume of fragmented rock, corresponds to the ratio of the average cutting force over the cross-sectional area of the groove created by the motion of the cutter; it is virtually independent of the depth of cut provided that the cutter is sufficiently sharp so that frictional dissipation beneath the cutter is negligible and also provided that the depth of cut is below a critical value dc that is proportional to the intrinsic length scale (KIc/q)2 with KIc denoting the rock toughness. Indeed, the critical depth of cut dc separates two regimes of cutting, ductile and brittle. In the ductile regime (depth of cut d smaller than dc but larger than the grain size), the rock is intensively sheared ahead of the cutter and the specific energy is constant. On the other hand, in the brittle regime (d larger than dc) chipping takes place and the specific energy decreases as the inverse square root of d. In sedimentary rocks, dcis typically less than 1 mm. The apparent correlation between the specific energy ɛ in the ductile regime and the uniaxial compressive strength q can be explained from an analysis of results of plane strain compression tests conducted in an apparatus that does not inhibit the development of shear bands (Labuz and Dai, J. of Geotechnical and Reoenvironmental Eng., 2000). This analysis indicates that the residual strength is reached on the shear band for slip distance of about 1~2 grain size and that the thickness of the shear band is also equal to about 2 grain size. Furthermore, the ratio of the energy required to destroy the cohesive links between the grains inside the shear band over the volume of

  12. An experiment system for testing synergetic erosion caused by sand abrasion and cavitation

    NASA Astrophysics Data System (ADS)

    Lu, L.; Liu, J.; Zhang, J. G.; Zhu, L.; Xu, H. Q.; Meng, X. C.; Yu, J. C.; Ma, S. P.; Wang, K.

    2014-03-01

    An advanced comprehensive test system, designed for testing synergetic erosion due to cavitation and sand abrasion in hydraulic machinery, is presented in this paper. This system includes an integrated test rig, control platform, and state-of-the-art measurement etc. For the integrated test system, there are three test modes, Venturi-section water tunnel, rotating disc and rotating disc with jet nozzle. The maximum velocity is 45 m/s for Venturi-section water tunnel test mode, and 85 m/s for rotating disc test mode. The pressure range for those two test modes can be regulated within -0.09 MPa~0.6 MPa. The highest flow relative velocity is 120 m/s for rotating disc with jet nozzle test mode. All key parameters measured from the test rig, such as flow discharge, pressure, sand concentration, temperature etc, can be displayed online and processed in the control platform. This new test system provides researchers with the possibility to measure cavitation erosion, sand abrasion and the synergetic damage in hydraulic machinery. Further, flow visualization analysis, weight loss measurements and erosion outline measurements are available using the system.

  13. Simplified Abrasion Test Methodology for Candidate EVA Glove Lay-Ups

    NASA Technical Reports Server (NTRS)

    Rabel, Emily; Aitchison, Lindsay

    2015-01-01

    During the Apollo Program, space suit outer-layer fabrics were badly abraded after performing just a few extravehicular activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots that penetrated the outer-layer fabric into the thermal protection layers after less than 8 hrs of surface operations. Current plans for the exploration planetary space suits require the space suits to support hundreds of hours of EVA on a lunar or Martian surface, creating a challenge for space suit designers to utilize materials advances made over the last 40 years and improve on the space suit fabrics used in the Apollo Program. Over the past 25 years the NASA Johnson Space Center Crew and Thermal Systems Division has focused on tumble testing as means of simulating wear on the outer layer of the space suit fabric. Most recently, in 2009, testing was performed on 4 different candidate outer layers to gather baseline data for future use in design of planetary space suit outer layers. In support of the High Performance EVA Glove Element of the Next Generation Life Support Project, testing a new configuration was recently attempted in which require 10% of the fabric per replicate of that need in 2009. The smaller fabric samples allowed for reduced per sample cost and flexibility to test small samples from manufacturers without the overhead to have a production run completed. Data collected from this iteration was compared to that taken in 2009 to validate the new test method. In addition the method also evaluated the fabrics and fabric layups used in a prototype thermal micrometeoroid garment (TMG) developed for EVA gloves under the NASA High Performance EVA Glove Project. This paper provides a review of previous abrasion studies on space suit fabrics, details methodologies used for abrasion testing in this particular study, results of the validation study, and results of the TMG testing.

  14. Bendable Extension For Abrasive-Jet Cleaning

    NASA Technical Reports Server (NTRS)

    Mayer, Walter

    1989-01-01

    Hard-to-reach places cleaned more easily. Extension for abrasive-jet apparatus bent to provide controlled abrasive cleaning of walls in deep cavities or other hard-to-reach places. Designed for controlled removal of penetrant inspection dyes from inside castings, extension tube also used for such general grit-blasting work as removal of scratches.

  15. Checking Out Cuts, Scratches, and Abrasions

    MedlinePlus

    ... For extra protection, your parent might use an antibacterial (say: an-tye-bak-TEER-ee-ul) ointment ... into the wound. The doctor might prescribe an antibiotic (say: an-tye-bye-AH-tik) medicine to ...

  16. Scratches: At What Price Quality

    NASA Astrophysics Data System (ADS)

    Slater, John A.; Cox, Dennis A.

    1986-11-01

    Scratch quality assessment is an emotive subject between users and suppliers with the topic being far more complex than one would imagine. The ultimate objective must be to be able to determine if and by how much scratches affect optical performance. However before this topic can be addressed with confidence objective methods of scratch measurement need to be established in order that organisations can agree on the relative severity of individual scratches. An important element in this process is the definition and production of standard scratch artefacts which will provide the vehicle for assessment either by visual or machine assisted means. This paper reviews a comparative experiment which set out to correlate existing British Standard scratches with those used in the United States in conjunction with MIL-0-13830A. The results of the experiment showed considerable inconsistency between operators regarding relative severity of the sample scratches and poor correlation between sets of supposedly standard scratches. The visual test was followed by a machine assisted evaluation which removed the subjective discrepancies between individual operators but confirmed the inconsistencies within National Standard scratch artefacts. Until such time that scratch quantification can be achieved by optical performance alone, machine assisted methods and good standard artefacts need to be developed which provide results which are consistent with manual use of artefacts.

  17. Relationships Between Abrasive Wear, Hardness, and Surface Grinding Characteristics of Titanium-Based Metal Matrix Composites

    SciTech Connect

    Blau, Peter Julian; Jolly, Brian C

    2009-01-01

    The objective of this work was to support the development of grinding models for titanium metal-matrix composites (MMCs) by investigating possible relationships between their indentation hardness, low-stress belt abrasion, high-stress belt abrasion, and the surface grinding characteristics. Three Ti-based particulate composites were tested and compared with the popular titanium alloy Ti-6Al-4V. The three composites were a Ti-6Al-4V-based MMC with 5% TiB{sub 2} particles, a Ti-6Al-4V MMC with 10% TiC particles, and a Ti-6Al-4V/Ti-7.5%W binary alloy matrix that contained 7.5% TiC particles. Two types of belt abrasion tests were used: (a) a modified ASTM G164 low-stress loop abrasion test, and (b) a higher-stress test developed to quantify the grindability of ceramics. Results were correlated with G-ratios (ratio of stock removed to abrasives consumed) obtained from an instrumented surface grinder. Brinell hardness correlated better with abrasion characteristics than microindentation or scratch hardness. Wear volumes from low-stress and high-stress abrasive belt tests were related by a second-degree polynomial. Grindability numbers correlated with hard particle content but were also matrix-dependent.

  18. Continuous Monitoring of Pin Tip Wear and Penetration into Rock Surface Using a New Cerchar Abrasivity Testing Device

    NASA Astrophysics Data System (ADS)

    Hamzaban, Mohammad-Taghi; Memarian, Hossein; Rostami, Jamal

    2014-03-01

    Evaluation of rock abrasivity is important when utilizing mechanized excavation in various mining and civil projects in hard rock. This is due to the need for proper selection of the rock cutting tools, estimation of the tool wear, machine downtime for cutter change, and costs. The Cerchar Abrasion Index (CAI) test is one of the simplest and most widely used methods for evaluating rock abrasivity. In this study, a new device for the determination of frictional forces and depth of pin penetration into the rock surface during a Cerchar test is discussed. The measured parameters were used to develop an analytical model for calculation of the size of the wear flat (and hence a continuous measure of CAI as the pin moves over the sample) and pin tip penetration into the rock during the test. Based on this model, continuous curves of CAI changes and pin tip penetration into the rock were plotted. Results of the model were used for introduction of a new parameter describing rock-pin interaction and classification of rock abrasion.

  19. Cat scratch disease (image)

    MedlinePlus

    Cat scratch disease is an infectious illness associated with cat scratches, bites, or exposure to cat saliva, causing chronic swelling of the lymph nodes. Cat scratch disease is possibly the most common cause of ...

  20. Cat scratch disease (image)

    MedlinePlus

    Cat scratch disease is an infectious illness associated with cat scratches, bites, or exposure to cat saliva, causing chronic swelling of the lymph nodes. Cat scratch disease is possibly the most common cause of chronic ...

  1. Abrasion-resistant antireflective coating for polycarbonate

    NASA Technical Reports Server (NTRS)

    Wydeven, T. J.

    1978-01-01

    Following plasma-polymerization technique, treatment in oxygen glow discharge further enhances abrasion resistance and transmission. Improvement in abrasion resistance was shown by measuring percentage of haze resulting from abrasion. Coating samples were analyzed for abrasion using standard fresh rubber eraser. Other tests included spectra measurements and elemental analysis with spectrometers and spectrophotometers.

  2. Effect of residual chips on the material removal process of the bulk metallic glass studied by in situ scratch testing inside the scanning electron microscope

    SciTech Connect

    Huang Hu; Zhao Hongwei; Shi Chengli; Wu Boda; Fan Zunqiang; Wan Shunguang; Geng Chunyang

    2012-12-15

    Research on material removal mechanism is meaningful for precision and ultra-precision manufacturing. In this paper, a novel scratch device was proposed by integrating the parasitic motion principle linear actuator. The device has a compact structure and it can be installed on the stage of the scanning electron microscope (SEM) to carry out in situ scratch testing. Effect of residual chips on the material removal process of the bulk metallic glass (BMG) was studied by in situ scratch testing inside the SEM. The whole removal process of the BMG during the scratch was captured in real time. Formation and growth of lamellar chips on the rake face of the Cube-Corner indenter were observed dynamically. Experimental results indicate that when lots of chips are accumulated on the rake face of the indenter and obstruct forward flow of materials, materials will flow laterally and downward to find new location and direction for formation of new chips. Due to similar material removal processes, in situ scratch testing is potential to be a powerful research tool for studying material removal mechanism of single point diamond turning, single grit grinding, mechanical polishing and grating fabrication.

  3. Scratch resistance of the ventral skin surface in four snake species (Squamata, Serpentes).

    PubMed

    Klein, Marie-Christin G; Gorb, Stanislav N

    2016-04-01

    Snakes are limbless tetrapods highly specialized for sliding locomotion on various substrates. Their skin is constantly exposed to high friction forces, which promotes abrasion. Snake skin has material and surface specializations, presumably optimized for friction and abrasion resistance. We found that different snake species living in different habitats have different abrasion patterns and hypothesized that this correlates with specific epidermal architecture and surface topography. To test this hypothesis artificial scratches, under controlled load conditions, were created on the ventral skin material (epidermis) of four snake species adapted to different habitats: Lampropeltis getula californiae (stony and sandy soil substrates), Epicrates cenchria cenchria (trees, soil and water), Morelia viridis (trees), and Gongylophis colubrinus (burrowing in sand). Abrasion appearance on the skin surface was examined using scanning electron microscopy and white light interferometry. The material failure was different between the species, which we attribute to differences in the epidermis' response to the same abrasive challenge. We also discuss abrasion resistance mechanisms and the correlation with the different ultrastructure and surface microstructure. PMID:26874374

  4. Monitoring and Testing the Parts Cleaning Stations, Abrasive Blasting Cabinets, and Paint Booths

    NASA Technical Reports Server (NTRS)

    Jordan, Tracee M.

    2004-01-01

    I have the opportunity to work in the Environmental Management Office (EMO) this summer. One of the EMO's tasks is to make sure the Environmental Management System is implemented to the entire Glenn Research Center (GRC). The Environmental Management System (EMS) is a policy or plan that is oriented toward minimizing an organization's impact to the environment. Our EMS includes the reduction of solid waste regeneration and the reduction of hazardous material use, waste, and pollution. With the Waste Management Team's (WMT) help, the EMS can be implemented throughout the NASA Glenn Research Center. The WMT is responsible for the disposal and managing of waste throughout the GRC. They are also responsible for the management of all chemical waste in the facility. My responsibility is to support the waste management team by performing an inventory on parts cleaning stations, abrasive cabinets, and paint booths through out the entire facility. These booths/stations are used throughout the center and they need to be monitored and tested for hazardous waste and material. My job is to visit each of these booths/stations, take samples of the waste, and analyze the samples.

  5. Corneal Abrasions

    MedlinePlus

    ... can also be scratched by a fingernail, a tree branch or a contact lens that is dry ... young children's fingernails short, also. Trim low-hanging tree branches. Use care when putting in contact lenses, ...

  6. Microstructural effects in abrasive wear. Quarterly progress report, December 1980-1 June 1981. [Alloys for use in coal mining, handling, and gasification

    SciTech Connect

    Kosel, T.H.; Rao, M.C.; Shetty, H.R.; Fernandes, M.T.; Fiore, N.F.

    1981-10-29

    This report describes research aimed at establishing quantitative relationships between microstructure and wear resistance of highly alloyed materials, including high-Cr white irons and experimental Co-base and Ni-base powder metallurgy (PM) alloys now used or potentially to be used in coal mining, handling, and gasification. The specific types of wear under study are low-stress abrasion and gouging wear encountered in mining, coal conversion, and transfer applications. During this period, work was concentrated on analysis of results. The many detailed observations obtained in the work on scratch test simulations of abrasive wear mechanisms have been summarized in drafts of three papers. The first, A Study of Abrasive Wear Mechanisms Using Diamond and Alumina Scratch Tests, is included as an appendix to this report and is being submitted for publication. Revision of the other papers is in progress.

  7. Using scratch testing to measure the adhesion strength of calcium phosphate coatings applied to poly(carbonate urethane) substrates.

    PubMed

    Barnes, Dunstan; Johnson, Scott; Snell, Robert; Best, Serena

    2012-02-01

    Bioactive coatings are applied to components of modern orthopædic implants to improve the host tissue response to the implants. Such coatings cannot be applied to polymeric implants by high-temperature techniques, because the use of high temperatures may critically degrade the polymer substrate. Regardless of the coating technique that is used, the coating must be sufficiently well adhered to the underlying substrate to provide any practical benefit. This paper investigates the use of scratch testing to measure the adhesion strength of calcium phosphate (CaP) coatings that were applied to a poly(carbonate urethane) (PCU) substrate by an aqueous process at temperatures of 19, 28, 37, and 50 °C. This work represents the first time that scratch testing analysis has been used to study CaP coatings deposited by an aqueous, low-temperature process on to a polymer substrate. Scratch testing was shown to be a useful technique for obtaining comparative, rather than absolute, values of adhesion strength for hard coatings formed on a compliant substrate. Generally, the coating temperature was not found to influence the CaP-PCU adhesion strength. Although CaP coatings formed at 19 °C exhibited considerably lower adhesion strengths than CaP coatings formed at 28, 37, and 50 °C, this finding was attributable to the inconsistency of CaP coatings formed on the PCU substrates at 19 °C. The coating-substrate adhesion strength was measured for CaP coatings of four different coating ages (0, 1, 2, and 3 years). CaP coatings that were aged for 0, 1, or 2 years exhibited similar coating-substrate adhesion strengths to each other. In contrast, CaP coatings that were aged for 3 years demonstrated considerably lower coating-substrate adhesion strengths. The observed reduction in adhesion strength with age was thought to be attributable to suspected "drying out" of the CaP coatings. PMID:22301182

  8. Surface carbonization of titanium for abrasion-resistant implant materials.

    PubMed

    Zhu, Yuhe; Watari, Fumio

    2007-03-01

    Carbide layer was formed on the surface of Ti by heating in hydrocarbon atmosphere (benzene C6H6) at 1000-1400 degrees C using a high frequency induction heating method. Physical and mechanical properties of carbide-coated Ti were investigated to examine its potential as an abrasion-resistant implant material. Scanning electron microscopy (SEM) showed that the surface of Ti was covered with fine grains of 1-4 microm diameter, depending on heating conditions. In addition, carbide layer of about 1-25 microm thickness was observed on the cross-section of specimens by SEM and energy dispersive spectroscopy. Vickers hardness of surface carbide was found to be more than 2000. Further, Martens scratch test and ultrasonic scaler abrasion test showed that the indentation depth and width of carbide-coated Ti were much smaller than pure Ti, thereby confirming its high abrasion resistance. These results showed that for Ti implant materials that require high abrasion resistance, such as the abutment for dental implants, surface carbide coatings would be an effective means to improve their wear properties. PMID:17621941

  9. Cat scratch disease.

    PubMed

    Bozhkov, V; Madjov, R; Plachkov, I; Arnaudov, P; Chernopolsky, P; Krasnaliev, I

    2014-01-01

    Approximately 24,000 people are infected with cat scratch disease (CSD) every year. CSD is caused by the bacteria Bartonella henselae, a gram-negative bacteria most often transmitted to humans through a bite or scratch from an infected cat or kitten. Although CSD is often a benign and self-limiting condition, it can affect any major organ system in the body, manifesting in different ways and sometimes leading to lifelong sequelae. It is a disease that is often overlooked in primary care because of the wide range of symptom presentation and relative rarity of serious complications. It is important for health care providers to recognize patients at risk for CSD, know what laboratory testing and treatments are available, and be aware of complications that may arise from this disease in the future. PMID:25199244

  10. The Mars Environmental Compatibility Assessment (MECA) Abrasion Tool

    NASA Technical Reports Server (NTRS)

    Kuhlman, K. R.; Anderson, M. S.; Hinde, B. D.; Hecht, M. H.; Pike, W. T.; Marshall, J. R.; Meloy, T. P.

    1999-01-01

    The Mars Environmental Compatibility Assessment (MECA) experiment, an instrument suite to be flown on Mars Surveyor 2001, will include a tool for doing simple mineralogical scratch and streak tests on particles from the Martian regolith. The Abrasion Tool will be applied to particles that adhere themselves to highly polished substrates of various hardnesses. Granular soil components will be subjected to a compressive force of about 3 N using a leaf spring. The spring will be applied with a paraffin actuator capable of a 0.76 mm throw to achieve a maximum displacement of about 7.5 mm at the tip of the tool. The pressure per grain will be dependent on the grain size, the number of grains that adhere to the substrate and the number of grains in compression. The pressure per particle is expected to be on the order of 100 MPa - 1 GPa. The MECA sample wheel containing the substrates will be rotated after the particles are placed in compression to produce scratches or pits. A primary goal of the Abrasion Tool is to identify quartz (Mohs' hardness = 7) using substrates of varying hardnesses. Quartz is considered hazardous to future human explorers of Mars because it can cause silicosis of the lungs if it is of respirable size. It is also hazardous to machinery, structures, and space suits because of its ability to abrade and scratch surfaces. Since large quantities of minerals harder than quartz are not expected, any scratches produced on polished quartz substrates might be reasonably attributed to quartz particles, although there may be minerals such as impact metamorphic diamond in the soils. Careful calibration of the tool will be necessary to ensure that grains are not overloaded; for example, a steel ball pressed into glass will produce a Hertzian fracture, even though it is softer than glass. Other minerals, such as magnetite (Mohs' hardness = 6.5) have been shown to scratch glass ceramics such as Zerodur (Mohs' hardness = 6.5). Thus, minerals can be differentiated

  11. The Mars Environmental Compatibility Assessment MECA Abrasion Tool

    NASA Astrophysics Data System (ADS)

    Kuhlman, K. R.; Anderson, M. S.; Hinde, B. D.; Hecht, M. H.; Pike, W. T.; Marshall, J.; Meloy, T. P.; Cobbly, T.

    1999-09-01

    The Mars Environmental Compatibility Assessment (MECA) experiment, an instrument suite to be flown on Mars Surveyor 2001, will include a tool for doing simple mineralogical scratch and streak tests on particles from the Martian regolith. The Abrasion Tool will be applied to particles that adhere to highly polished substrates of various hardnesses. Granular soil components will be subjected to a compressive force of about 3 N using a leaf spring. The spring will be applied with a paraffin actuator capable of a 0.76 mm throw to achieve a maximum displacement of about 7.5 mm at the tip of the tool. The pressure per grain will be dependent on the grain size, the number of grains that adhere to the substrate and the number of grains in compression. The pressure per particle is expected to be on the order of 100 MPa - 1 GPa. The MECA sample wheel containing the substrates will be rotated after the particles are placed in compression to produce scratches or pits. A primary goal of the Abrasion Tool is to identify quartz (Mohs' hardness = 7) using substrates of varying hardnesses. Quartz is considered hazardous to future human explorers of Mars because it can cause silicosis of the lungs if it is of respirable size. It is also hazardous to machinery, structures, and space suits because of its ability to abrade and scratch surfaces. Since large quantities of minerals harder than quartz are not expected, any scratches produced on polished quartz substrates might be reasonably attributed to quartz particles, although there may be minerals such as impact metamorphic diamond in the soils. Careful calibration of the tool will be necessary to ensure that grains are not overloaded; for example, a steel ball pressed into glass will produce a Hertzian fracture, even though it is softer than glass. Other minerals, such as magnetite (Mohs'hardness = 6.5) have been shown to scratch glass ceramics such as Zerodur (Mohs' hardness = 6.5). Thus, minerals can be differentiated: note that

  12. The Mars Environmental Compatibility Assessment MECA Abrasion Tool

    NASA Technical Reports Server (NTRS)

    Kuhlman, K. R.; Anderson, M. S.; Hinde, B. D.; Hecht, M. H.; Pike, W. T.; Marshall, J.; Meloy, T. P.; Cobbly, T.

    1999-01-01

    The Mars Environmental Compatibility Assessment (MECA) experiment, an instrument suite to be flown on Mars Surveyor 2001, will include a tool for doing simple mineralogical scratch and streak tests on particles from the Martian regolith. The Abrasion Tool will be applied to particles that adhere to highly polished substrates of various hardnesses. Granular soil components will be subjected to a compressive force of about 3 N using a leaf spring. The spring will be applied with a paraffin actuator capable of a 0.76 mm throw to achieve a maximum displacement of about 7.5 mm at the tip of the tool. The pressure per grain will be dependent on the grain size, the number of grains that adhere to the substrate and the number of grains in compression. The pressure per particle is expected to be on the order of 100 MPa - 1 GPa. The MECA sample wheel containing the substrates will be rotated after the particles are placed in compression to produce scratches or pits. A primary goal of the Abrasion Tool is to identify quartz (Mohs' hardness = 7) using substrates of varying hardnesses. Quartz is considered hazardous to future human explorers of Mars because it can cause silicosis of the lungs if it is of respirable size. It is also hazardous to machinery, structures, and space suits because of its ability to abrade and scratch surfaces. Since large quantities of minerals harder than quartz are not expected, any scratches produced on polished quartz substrates might be reasonably attributed to quartz particles, although there may be minerals such as impact metamorphic diamond in the soils. Careful calibration of the tool will be necessary to ensure that grains are not overloaded; for example, a steel ball pressed into glass will produce a Hertzian fracture, even though it is softer than glass. Other minerals, such as magnetite (Mohs'hardness = 6.5) have been shown to scratch glass ceramics such as Zerodur (Mohs' hardness = 6.5). Thus, minerals can be differentiated: note that

  13. Adhesion and wear behaviour of NCD coatings on Si3N4 by micro-abrasion tests.

    PubMed

    Silva, F G; Neto, M A; Fernandes, A J S; Costa, F M; Oliveira, F J; Silva, R F

    2009-06-01

    Nanocrystalline diamond (NCD) coatings offer an excellent alternative for tribological applications, preserving most of the intrinsic mechanical properties of polycrystalline CVD diamond and adding to it an extreme surface smoothness. Silicon nitride (Si3N4) ceramics are reported to guarantee high adhesion levels to CVD microcrystalline diamond coatings, but the NCD adhesion to Si3N4 is not yet well established. Micro-abrasion tests are appropriate for evaluating the abrasive wear resistance of a given surface, but they also provide information on thin film/substrate interfacial resistance, i.e., film adhesion. In this study, a comparison is made between the behaviour of NCD films deposited by hot-filament chemical vapour deposition (HFCVD) and microwave plasma assisted chemical vapour deposition (MPCVD) techniques. Silicon nitride (Si3N4) ceramic discs were selected as substrates. The NCD depositions by HFCVD and MPCVD were carried out using H2-CH4 and H2-CH4-N2 gas mixtures, respectively. An adequate set of growth parameters was chosen for each CVD technique, resulting in NCD films having a final thickness of 5 microm. A micro-abrasion tribometer was used, with 3 microm diamond grit as the abrasive slurry element. Experiments were carried out at a constant rotational speed (80 r.p.m.) and by varying the applied load in the range of 0.25-0.75 N. The wear rate for MPCVD NCD (3.7 +/- 0.8 x 10(-5) mm3 N(-1) m(-1)) is compatible with those reported for microcrystalline CVD diamond. The HFCVD films displayed poorer adhesion to the Si3N4 ceramic substrates than the MPCVD ones. However, the HFCVD films show better wear resistance as a result of their higher crystallinity according to the UV Raman data, despite evidencing premature adhesion failure. PMID:19504945

  14. Microstructural effects in abrasive wear. Quarterly progress report, June 1981-January 1982

    SciTech Connect

    Kosel, T.H.; Rao, C.M.; Fernandes, M.T.; Fiore, N.F.

    1982-02-24

    This report describes research aimed at establishing quantitative relationships between microstructure and wear resistance of highly alloyed materials, including high-Cr white irons and powder metallurgy (PM) alloys now used or potentially to be used in coal mining, handling, and gasification. The specific types of wear under study are low-stress abrasion and gouging wear encountered in mining, coal conversion, and transfer applications. Recent work has concentrated on analysis of results. The many detailed observations obtained in the work on scratch test simulations of abrasive wear mechanisms have been summarized in drafts of three papers. The first, a study of abrasive wear mechanisms using diamond and alumina scratch tests, was included as an appendix to Quarterly Report 16/17 and has been accepted for publication in the journal Wear. Revision of the other two papers is in progress. Two papers representing our analysis of results are included as appendices to this report. The first, abrasion in multiphase alloys, was presented at the NACE conference on corrosion-erosion-wear of materials at Berkeley, California in January 1982, and will be published in the proceedings. The second, on a deformation-induced phase transformation during abrasive wear of Co-base alloys, is being submitted for publication in Metallurgical Transactions. In addition, work on the gouging abrasion resistance of the previously tested high Cr-Mo white cast irons is completed. The abstract of a short paper on the results is included as an appendix. (Note: since the appendices are, or will be, available in the open literature they have been removed from the report.)

  15. Cat Scratch Disease

    MedlinePlus

    Cat scratch disease (CSD) is an illness caused by the bacterium Bartonella henselae. Almost half of all cats carry ... infection does not make cats sick. However, the scratch or bite of an infected cat can cause ...

  16. Study of abrasive wear rate of silicon using n-alcohols

    NASA Technical Reports Server (NTRS)

    Danyluk, S.

    1982-01-01

    The work carried out at the University of Illinois at Chicago for the Flat-Plate Solar Array Project under contract No. 956053 is summarized. The abrasion wear rate of silicon in a number of fluid environments and the parameters that influence the surface mechanical properties of silicon were determined. Three tests were carried out in this study: circular and linear multiple-scratch test, microhardness test and a three-point bend test. The pertinent parameters such as effect of surface orientation, dopant and fluid properties were sorted. A brief review and critique of previous work is presented.

  17. Testing of Alternative Abrasives for Water-Jet Cutting at C Tank Farm

    SciTech Connect

    Krogstad, Eirik J.

    2013-08-01

    Legacy waste from defense-related activities at the Hanford Site has predominantly been stored in underground tanks, some of which have leaked; others may be at risk to do so. The U.S. Department of Energy’s goal is to empty the tanks and transform their contents into more stable waste forms. To do so requires breaking up, and creating a slurry from, solid wastes in the bottoms of the tanks. A technology developed for this purpose is the Mobile Arm Retrieval System. This system is being used at some of the older single shell tanks at C tank farm. As originally planned, access ports for the Mobile Arm Retrieval System were to be cut using a high- pressure water-jet cutter. However, water alone was found to be insufficient to allow effective cutting of the steel-reinforced tank lids, especially when cutting the steel reinforcing bar (“rebar”). The abrasive added in cutting the hole in Tank C-107 was garnet, a complex natural aluminosilicate. The hardness of garnet (Mohs hardness ranging from H 6.5 to 7.5) exceeds that of solids currently in the tanks, and was regarded to be a threat to Hanford Waste Treatment and Immobilization Plant systems. Olivine, an iron-magnesium silicate that is nearly as hard as garnet (H 6.5 to 7), has been proposed as an alternative to garnet. Pacific Northwest National Laboratory proposed to test pyrite (FeS2), whose hardness is slightly less (H 6 to 6.5) for 1) cutting effectiveness, and 2) propensity to dissolve (or disintegrate by chemical reaction) in chemical conditions similar to those of tank waste solutions. Cutting experiments were conducted using an air abrader system and a National Institute of Standards and Technology Standard Reference Material (SRM 1767 Low Alloy Steel), which was used as a surrogate for rebar. The cutting efficacy of pyrite was compared with that of garnet and olivine in identical size fractions. Garnet was found to be most effective in removing steel from the target; olivine and pyrite were less

  18. Microstructure and Scratch Resistance of TaC Dense Ceramic Layer on an Iron Matrix

    NASA Astrophysics Data System (ADS)

    Zhao, Nana; Xu, Yunhua; Zhong, Lisheng; Yan, Honghua; Ovcharenko, Vladimir E.

    2016-05-01

    A tantalum carbide dense ceramic layer with a thickness of ~20 μm was produced on the surface of an iron matrix using an in situ technique. The morphology, microstructure, and phase composition of the layer were characterized by means of SEM, TEM, and XRD. The results show fairly agglomerated and uniformly sized (~200 nm) TaC particulates with a face-cantered cubic structure. The values of nano-hardness for the surface and cross section of reinforcing layer can be as high as 29.5 ± 0.6 and 26.7 ± 0.1 GPa, respectively, which were analyzed using a nano-indentation apparatus. Moreover, the scratch resistance of the layer was measured by scratch tests under a progressively increasing load of 0-100 N. A high critical load of 90.4 N is obtained. It is worthy to note that there are only cracking, slight splitting, and small flaking pits (even at the maximum load) all over the whole scratch process, namely the reinforcing layer can protect the iron matrix from serious abrasion effectively. In addition, the excellent scratch resistance and mechanism are discussed in detail.

  19. Microstructure and Scratch Resistance of TaC Dense Ceramic Layer on an Iron Matrix

    NASA Astrophysics Data System (ADS)

    Zhao, Nana; Xu, Yunhua; Zhong, Lisheng; Yan, Honghua; Ovcharenko, Vladimir E.

    2016-06-01

    A tantalum carbide dense ceramic layer with a thickness of ~20 μm was produced on the surface of an iron matrix using an in situ technique. The morphology, microstructure, and phase composition of the layer were characterized by means of SEM, TEM, and XRD. The results show fairly agglomerated and uniformly sized (~200 nm) TaC particulates with a face-cantered cubic structure. The values of nano-hardness for the surface and cross section of reinforcing layer can be as high as 29.5 ± 0.6 and 26.7 ± 0.1 GPa, respectively, which were analyzed using a nano-indentation apparatus. Moreover, the scratch resistance of the layer was measured by scratch tests under a progressively increasing load of 0-100 N. A high critical load of 90.4 N is obtained. It is worthy to note that there are only cracking, slight splitting, and small flaking pits (even at the maximum load) all over the whole scratch process, namely the reinforcing layer can protect the iron matrix from serious abrasion effectively. In addition, the excellent scratch resistance and mechanism are discussed in detail.

  20. Tumbling experiments to test fragmentation and abrasion of rocks from the Southern Alps, New Zealand

    NASA Astrophysics Data System (ADS)

    Herman, F.; Fluekiger, L.; Cox, S. C.; Beyssac, O.

    2011-12-01

    Detrital cobbles and pebbles were collected from rivers draining the Southern Alps in the South Island of New Zealand. Our objective was to obtain a time-series of abrasion and fragmentation processes, in order to replicate fluvial processes and understand the relative erosion resistance of bedrock lithologies. Lithologies included variably metamorphosed greywacke-sandstone, semischist and schist, reflecting the range of rocks in the hangingwall of the Alpine Fault exhumed by differential uplift, and granite and gneiss in the footwall. Rocks were cut into 3cm cubes, weighed individually and washed in millipore water, then photographed. Experimental sample sets, matching the proportions of rock lithologies observed in the riverbeds, were placed in rectangular 20 litre containers together with 2 litres of fresh rainwater. Containers were rotated in a concrete mixer at 26 revolutions per minute for 2, 4, 12 and 49 hours, with a duplicate geochemical blank sample left for 50 hrs without tumbing. Each set of tumbled material was then extracted, photographed, classified, sorted into size fractions, weighed and saved for further analysis. Samples of sand, silt, rock-contaminated water and suspended sediment were also collected for filtering of suspended sediment, petrography and chemical analysis. Tumbling produced dramatic differences in the behaviour of different rocks, particularly in the relative strength of sandstone, semischist and schist lithologies. Cubes of schist fragmented into tabular pieces and rounded quickly, within two hours, compared with semischist and sandstone which retained cuboid forms and suffered only minor rounding of edges after 49 hours tumbling. Fine-grained material produced as a by-product was dominated by a silt/clay fraction that increased in quantity with tumbling time. Relatively little sand-sized sediment was generated, and its quantity decreased with tumbling time as it was also transformed into finer material. The experiment highlights

  1. Abrasion of restorative materials by toothaste.

    PubMed

    Heath, J R; Wilson, H J

    1976-04-01

    The procedure developed in this investigation is suitable for determining the abrasion resistance of restorative materials to toothbrush/dentifrice abrasion. Ideally, a restoration should have an abrasion resistance similar to that of enamel. Of the materials tested, gold was the only one that wore slightly less than enamel, whilst amalgam wore almost twice as quickly. The silicate material and composites (excluding TD.71) wear away 2-4 times faster than enamel. TD.71 and especially the unfilled resin exhibited very high rates of abrasion. After prolonged toothbrush/dentifrice abrasion, the surfaces of gold and amalgam were considerably smoother than those of the silicate and composite materials. PMID:1066445

  2. Microstructural effects in abrasive wear. Quarterly progress report, January 1-June 1, 1980

    SciTech Connect

    Fiore, N.F.; Kosel, T.H.; Channagiri, M.; Desai, V.; Fulcher, J.; Shetty, H.R.

    1980-06-01

    Research aimed at establishing quantitative relationships between microstructure and wear resistance of highly alloyed materials is described including high-Cr white irons and experimental Co-base and Ni-base powder metallurgy (PM) alloys now used or potentially to be used in coal mining, handling and gasification. The specific types of wear under study are low-stress abrasion and gouging wear encountered in mining, coal conversion and transfer applications. Research has concentrated on the investigation of wear in Co-base PM alloys No. 19 and No. 6, which have been sintered to provide different carbide sizes at the same volume fraction in each respective alloy. Low-stress abrasion tests using Al/sub 2/O/sub 3/ abrasive have been completed on Alloy No. 19 and the results show a monotonic decrease in wear rate with increasing size. A series of single-point scratch test simulations of abrasive wear mechanisms has been initiated, and these tests provide valuable insights into material removal processes in the Co-base alloys.

  3. Cat-Scratch Disease

    MedlinePlus

    ... and how do people get it? Cat-scratch disease is an infection caused by a type of bacteria (germs) carried in cat saliva. This bacteria is called Bartonella henselae and can be passed from a cat to a human. Doctors and ... from fleas. Cat-scratch disease is not a severe illness in people who ...

  4. Scratch behavior of polymers

    NASA Astrophysics Data System (ADS)

    Lim, Goy Teck

    This dissertation work is focused on the analytical and numerical examination of the mechanical response of polypropylene (PP) under scratch deformation by a semispherical indenter. The finite element (FE) method is employed as the analysis technique and ABAQUSRTM, a commercial FE package is adopted to perform the analysis. Important physical and computational considerations on the implementation of FE analyses for the scratch problem are reviewed. It is shown through the discussion of the generated results that a good understanding can be gained on how different scratch conditions can affect scratch behavior of PP. A phenomenological deduction of the scratch damage process and mechanisms is also established. Considering the two main damage modes of polymers, shear yielding and crazing, it is shown that the two damage modes not only exist in the scratch deformation, and moreover, that they may compete against each other for dominance. A parametric study is also performed to assess the influence of material and surface properties on scratch response of material. A secondary research effort is also made to investigate the material constitutive modeling of polymers. Focusing on elastomeric or rubbery materials, a new mixed network model between the Gaussian and eight-chain non-Gaussian models is proposed. This mixed model inherently preserves the good predictive power of these two models and yields better predictions over a wider range of deformation than that of the rubber model adopted by ABAQUSRTM .

  5. Scratch Cell Test: A Simple, Cost Effective Screening Tool to Evaluate Self-Healing in Anti-Corrosion Coatings

    NASA Astrophysics Data System (ADS)

    Rani, Amitha; Somaiah, Durga; Megha; Poddar, Mitalee

    2014-09-01

    A quick and simple scratch cell set up to evaluate the self-healing of an hybrid sol-gel (ormosil) coating was fabricated. This methacrylate-based anti-corrosion coating was applied on the aerospace aluminium alloy AA2024-T3, and cured at room temperature. This technique of evaluation requires minimum instrumentation. The inhibitors cerium nitrate, benzotriazole and 8-hydroxy quinoline (8-HQ) were used in the study. The self-healing ability of the inhibitors decreased in the following order: 8-HQ, BTZ and Ce. 8-HQ showed the highest self-healing ability and was comparable to the commercial hexavalent chromium conversion coating—Alodine. Spectroscopic analysis of the electrolyte and EDX of the coatings indicated the movement of the inhibitor from the coating to the site of damage, thereby effecting self-healing. It was observed that an increased inhibitor concentration in the coatings did not accelerate the healing process. Inhibitor release was slower in the coatings doped with inhibitor-loaded nano-containers, when compared to inhibitor-spiked coatings. This property of controlled release is desirable in self-healing coatings. Electro impedance studies further confirmed self-healing efficiency of the coatings. The scratch cell study reported here is the first of its kind with the ormosil under study on AA2024-T3 aluminium alloy. The results are encouraging and warranty a quick and simple qualitative screening of the self-healing potential of the inhibitors with minimum instrumentation.

  6. The increase in cobalt release in metal-on-polyethylene hip bearings in tests with third body abrasives.

    PubMed

    de Villiers, Danielle; Traynor, Alison; Collins, Simon N; Shelton, Julia C

    2015-09-01

    Hypersensitivity reactions in patients receiving metal-on-metal hip replacements have been attributed to corrosion products as observed by elevated cobalt and chromium ions in the blood. Although the majority of cases are reported in metal-on-metal, incidences of these reactions have been reported in the metal-on-polyethylene patient population. To date, no in vitro study has considered cobalt release for this bearing combination. This study considered four 28 mm and seven 52 mm diameter metal-on-polyethylene bearings tested following ISO standard hip simulator conditions as well as under established abrasive conditions. These tests showed measurable cobalt in all bearings under standard conditions. Cobalt release, as well as polyethylene wear, increased with diameter, increasing from 52 to 255 ppb. The introduction of bone cement particles into the articulation doubled polyethylene wear and cobalt release while alumina particles produced significant damage on the heads demonstrated by cobalt levels of 70,700 ppb and an increased polyethylene wear from a mean value of 9-160 mm(3)/mc. Cobalt release was indicative of head damage and correlated with polyethylene wear at the next gravimetric interval. The removal of third body particles resulted in continued elevated cobalt levels in the 52 mm diameter bearings tested with alumina compared to standard conditions but the bearings tested with bone cement particles returned to standard levels. The polyethylene wear in the bone cement tested bearings also recovered to standard levels, although the alumina tested bearings continued to wear at a higher rate of 475 mm(3)/mc. Cobalt release was shown to occur in metal-on-polyethylene bearings indicating damage to the metal head resulting in increased polyethylene wear. While large diameter metal-on-polyethylene bearings may provide an increased range of motion and a reduced dislocation risk, increased levels of cobalt are likely to be released and this needs to be fully

  7. Effect of grain size on scratch interactions and material removal in alumina

    SciTech Connect

    Xu, H.H.K.; Jahanmir, S.; Wang, Y.

    1995-04-01

    Dramatic effects of scratch interactions on material removal are observed in alumina. A series of parallel scratches are made in aluminas with different grain sizes to investigate the influence of scratch interactions on the material removal process in abrasive machining. The separation distance between the two scratches and the normal load are varied and subsurface microfracture and damage modes are examined to assess the mechanisms of material removal. A very small amount of material is removed when the separation distance between the two parallel scratches is large or when the two scratches completely overlap. However, at intermediate distances the volume of material removed increases dramatically as a result of the interactions between the two scratches. The maximum amount of material removed and the corresponding distance between the two scratches are found to depend strongly on the grain size and the load. Observations of surface and subsurface damage reveal that grain dislodgement is the predominant mechanism of material removal, irrespective of the grain size. The relation between grain size, scratch interactions, and the material removal process in grinding and abrasive machining of ceramics is discussed in terms of the short-crack toughness of ceramics.

  8. Transducer Abrasion test results in support of ultrasonic inspection of Double Shell Tanks (DST)

    SciTech Connect

    JENSEN, C.E.

    2003-02-01

    Identification of questionable ultrasonic data on 241-AN-105 lead to suggestions that the ultrasonic transducers were not properly installed causing excessive wear. This report documents the testing to validate the source of the improper data as being transducer wear. The results of the testing indicated that the wear influenced the data results and subsequently the analysis of the corrosion on the subject DST.

  9. Cat Scratch Disease

    MedlinePlus

    Cat scratch disease (CSD) is an illness caused by the bacterium Bartonella henselae. Almost half of all cats carry the infection ... symptoms of CSD, call your doctor. Centers for Disease Control and Prevention

  10. Cat-Scratch Disease

    MedlinePlus

    ... Patients Infants and Young Children Publications & Materials Announcements Cat-Scratch Disease Recommend on Facebook Tweet Share Compartir ( ... play and learn how to attack prey. How cats and people become infected Kitten playing with a ...

  11. The increase in cobalt release in metal-on-polyethylene hip bearings in tests with third body abrasives

    PubMed Central

    de Villiers, Danielle; Traynor, Alison; Collins, Simon N; Shelton, Julia C

    2015-01-01

    Hypersensitivity reactions in patients receiving metal-on-metal hip replacements have been attributed to corrosion products as observed by elevated cobalt and chromium ions in the blood. Although the majority of cases are reported in metal-on-metal, incidences of these reactions have been reported in the metal-on-polyethylene patient population. To date, no in vitro study has considered cobalt release for this bearing combination. This study considered four 28 mm and seven 52 mm diameter metal-on-polyethylene bearings tested following ISO standard hip simulator conditions as well as under established abrasive conditions. These tests showed measurable cobalt in all bearings under standard conditions. Cobalt release, as well as polyethylene wear, increased with diameter, increasing from 52 to 255 ppb. The introduction of bone cement particles into the articulation doubled polyethylene wear and cobalt release while alumina particles produced significant damage on the heads demonstrated by cobalt levels of 70,700 ppb and an increased polyethylene wear from a mean value of 9–160 mm3/mc. Cobalt release was indicative of head damage and correlated with polyethylene wear at the next gravimetric interval. The removal of third body particles resulted in continued elevated cobalt levels in the 52 mm diameter bearings tested with alumina compared to standard conditions but the bearings tested with bone cement particles returned to standard levels. The polyethylene wear in the bone cement tested bearings also recovered to standard levels, although the alumina tested bearings continued to wear at a higher rate of 475 mm3/mc. Cobalt release was shown to occur in metal-on-polyethylene bearings indicating damage to the metal head resulting in increased polyethylene wear. While large diameter metal-on-polyethylene bearings may provide an increased range of motion and a reduced dislocation risk, increased levels of cobalt are likely to be released and this needs to be

  12. Test chamber and forensic microscopy investigation of the transfer of brominated flame retardants into indoor dust via abrasion of source materials.

    PubMed

    Rauert, C; Harrad, S; Suzuki, G; Takigami, H; Uchida, N; Takata, K

    2014-09-15

    Brominated flame retardants (BFRs) have been detected in indoor dust in many studies, at concentrations spanning several orders of magnitude. Limited information is available on the pathways via which BFRs migrate from treated products into dust, yet the different mechanisms hypothesized to date may provide an explanation for the range of reported concentrations. In particular, transfer of BFRs to dust via abrasion of particles or fibers from treated products may explain elevated concentrations (up to 210 mg g(-1)) of low volatility BFRs like decabromodiphenyl ether (BDE-209). In this study, an indoor dust sample containing a low concentration of hexabromocyclododecane, or HBCD, (110 ng g(-1) ΣHBCDs) was placed on the floor of an in-house test chamber. A fabric curtain treated with HBCDs was placed on a mesh shelf 3 cm above the chamber floor and abrasion induced using a stirrer bar. This induced abrasion generated fibers of the curtain, which contaminated the dust, and ΣHBCD concentrations in the dust increased to between 4020 and 52 500 ng g(-1) for four different abrasion experiment times. The highly contaminated dust (ΣHBCD at 52 500 ng g(-1)) together with three archived dust samples from various UK microenvironments, were investigated with forensic microscopy techniques. These techniques included Micro X-ray fluorescent spectroscopy, scanning emission microscopy coupled with an energy dispersive X-ray spectrometer, Fourier transform infrared spectroscopy with further BFR analysis on LC-MS/MS. Using these techniques, fibers or particles abraded from a product treated with BFRs were identified in all dust samples, thereby accounting for the elevated concentrations detected in the original dust (3500 to 88 800 ng g(-1) ΣHBCD and 24 000 to 1,438 000 ng g(-1) for BDE-209). This study shows how test chamber experiments alongside forensic microscopy techniques, can provide valuable insights into the pathways via which BFRs contaminate indoor dust. PMID:24984234

  13. The abrasion and impact-abrasion behavior of austempered ductile irons

    SciTech Connect

    Hawk, Jeffrey A.; Dogan, Omer N.; Lerner, Y.S.

    1998-01-01

    Austempering of ductile irons has led to a new class of irons, Austempered Ductile Irons (ADIs), with improved mechanical strength and fracture toughness lacking in gray cast irons. Laboratory wear tests have been used to evaluate the abrasive and impact-abrasive wear behavior of a suite of ADIs. The use of high-stress, two-body abrasion, low-stress, three-body abrasion, and impact-abrasion tests provides a clear picture of the abrasive wear behavior of the ADIs and the mechanisms of material removal. When combined with hardness measurements, fracture toughness and a knowledge of the microstructure of the ADIs, the overall performance can be assessed relative to more wear resistant materials such as martensitic steels and high-chromium white cast irons

  14. Scratch encourages selective doping

    NASA Technical Reports Server (NTRS)

    Hawrylo, F. Z.; Kressel, H.

    1980-01-01

    Dislocations induced by scratching produce deep narrow spikes of zinc diffused in gallium arsenide. Density of defects formed locally increases zinc diffusion coefficient. Enhancements by factor of 6 have been observed. Technique works for other dopants than zinc and for other semiconductors besides GaAs.

  15. Cat Scratch Disease (For Parents)

    MedlinePlus

    ... Story" 5 Things to Know About Zika & Pregnancy Cat Scratch Disease KidsHealth > For Parents > Cat Scratch Disease Print A A A Text Size ... Doctor en español Enfermedad por arañazo de gato Cat scratch disease is a bacterial infection that a ...

  16. Experimental, numerical and analytical studies of abrasive wear: correlation between wear mechanisms and friction coefficient

    NASA Astrophysics Data System (ADS)

    Mezlini, Salah; Zidi, M.; Arfa, H.; Ben Tkaya, Mohamed; Kapsa, Philippe

    2005-11-01

    The transport of granular material often generates severe damage. Understanding the correlation between the friction coefficient, particle geometry and wear mechanisms is of primary importance for materials undergoing abrasive wear. The aim of this study is to investigate the effect of particle geometry on wear mechanisms and the friction coefficient. Numerical and analytical simulations and experimental results have been compared. The process to be studied is the scratch made by a rigid cone with different attack angles on a 5xxx aluminium alloy (Al-Mg) flat surface. A scratch test was used and the wear mechanisms were observed for different attack angles. A numerical study with a finite element code was made in order to understand the effect of attack angle on the friction coefficient. The contact surface and the friction coefficient were also studied, and the results compared to the Bowden and Tabor model. The superposition of the numerical, analytical and experimental results showed a better correlation between the wear mechanisms and the friction coefficient. It also showed the importance of the model hypothesis used to simulate the scratch phenomenon. To cite this article: S. Mezlini et al., C. R. Mecanique 333 (2005).

  17. The measurement of abrasive particles velocities in the process of abrasive water jet generation

    NASA Astrophysics Data System (ADS)

    Zeleňák, Michal; Foldyna, Josef; Říha, Zdeněk

    2014-08-01

    An optimization of the design of the abrasive cutting head using the numerical simulation requires gathering as much information about processes occurring in the cutting head as possible. Detailed knowledge of velocities of abrasive particles in the process of abrasive water jet generation is vital for the verification of the numerical model. A method of measurement of abrasive particles at the exit of focusing tube using the FPIV technique was proposed and preliminary tests are described in the paper. Results of analysis of measured velocity fields are presented in the paper.

  18. Scratching Where They Itch: Evaluation of Feedback on a Diagnostic English Grammar Test for Taiwanese University Students

    ERIC Educational Resources Information Center

    Yin, Muchun; Sims, James; Cothran, Daniel

    2012-01-01

    Feedback to the test taker is a defining characteristic of diagnostic language testing (Alderson, 2005). This article reports on a study that investigated how much and in what ways students at a Taiwan university perceived the feedback to be useful on an online multiple-choice diagnostic English grammar test, both in general and by students of…

  19. Profiling the third-body wear damage produced in CoCr surfaces by bone cement, CoCr, and Ti6Al4V debris: a 10-cycle metal-on-metal simulator test.

    PubMed

    Halim, Thomas; Burgett, Michelle; Donaldson, Thomas K; Savisaar, Christina; Bowsher, John; Clarke, Ian C

    2014-07-01

    Particles of bone cement (polymethyl methacrylate), CoCr and Ti6Al4V were compared for their abrasion potential against CoCr substrates. This appears to be the first study utilizing CoCr and Ti6Al4V particulates to abrade CoCr bearings and the first study profiling the morphology of third-body abrasive wear scratches in a hip simulator. The 5 mg debris allotments (median size range 140-300 µm) were added to cups mounted both inverted and anatomically with metal-on-metal (MOM) bearings in a 10-cycle, hip simulator test. Surface abrasion was characterized by roughness indices and scratch profiles. Compared to third-body abrasion with metal debris, polymethyl methacrylate debris had minimal effect on the CoCr surfaces. In all, 10 cycles of abrasion with metal debris demonstrated that roughness indices (Ra, PV) increased approximately 20-fold from the unworn condition. The scratch profiles ranged 20-108 µm wide and 0.5-2.8 µm deep. The scratch aspect ratio (W/PV) averaged 0.03, and this very low ratio indicated that the 140 µm CoCr beads had plastically deformed to create wide but shallow scratches. There was no evidence of transfer of CoCr beads to CoCr bearings. The Ti64 particles produced similar scratch morphology with the same aspect ratio as the CoCr particulates. However, the titanium particulates also showed a unique ability to flatten and adhere to the CoCr, forming smears and islands of contaminating metal on the CoCr bearings. The morphology of scratches and metal transfer produced by these large metal particulates in the simulator appeared identical to those reported on retrieved metal-on-metal bearings. PMID:25062741

  20. New iron-based SiC spherical composite magnetic abrasive for magnetic abrasive finishing

    NASA Astrophysics Data System (ADS)

    Zhang, Guixiang; Zhao, Yugang; Zhao, Dongbiao; Zuo, Dunwen; Yin, Fengshi

    2013-03-01

    SiC magnetic abrasive is used to polish surfaces of precise, complex parts which are hard, brittle and highly corrosion-resistant in magnetic abrasive finishing(MAF). Various techniques are employed to produce this magnetic abrasive, but few can meet production demands because they are usually time-consuming, complex with high cost, and the magnetic abrasives made by these techniques have irregular shape and low bonding strength that result in low processing efficiency and shorter service life. Therefore, an attempt is made by combining gas atomization and rapid solidification to fabricate a new iron-based SiC spherical composite magnetic abrasive. The experimental system to prepare this new magnetic abrasive is constructed according to the characteristics of gas atomization and rapid solidification process and the performance requirements of magnetic abrasive. The new iron-based SiC spherical composite magnetic abrasive is prepared successfully when the machining parameters and the composition proportion of the raw materials are controlled properly. Its morphology, microstructure, phase composition are characterized by scanning electron microscope(SEM) and X-ray diffraction(XRD) analysis. The MAF tests on plate of mold steel S136 are carried out without grinding lubricant to assess the finishing performance and service life of this new SiC magnetic abrasive. The surface roughness( R a) of the plate worked is rapidly reduced to 0.051 μm from an initial value of 0.372 μm within 5 min. The MAF test is carried on to find that the service life of this new SiC magnetic abrasive reaches to 155 min. The results indicate that this process presented is feasible to prepare the new SiC magnetic abrasive; and compared with previous magnetic abrasives, the new SiC spherical composite magnetic abrasive has excellent finishing performance, high processing efficiency and longer service life. The presented method to fabricate magnetic abrasive through gas atomization and rapid

  1. Learning computer science concepts with Scratch

    NASA Astrophysics Data System (ADS)

    Meerbaum-Salant, Orni; Armoni, Michal; (Moti) Ben-Ari, Mordechai

    2013-09-01

    Scratch is a visual programming environment that is widely used by young people. We investigated if Scratch can be used to teach concepts of computer science (CS). We developed learning materials for middle-school students that were designed according to the constructionist philosophy of Scratch and evaluated them in a few schools during two years. Tests were constructed based upon a novel combination of the revised Bloom taxonomy and the Structure of the Observed Learning Outcome taxonomy. These instruments were augmented with qualitative tools, such as observations and interviews. The results showed that students could successfully learn important concepts of CS, although there were problems with some concepts such as repeated execution, variables, and concurrency. We believe that these problems can be overcome by modifications to the teaching process that we suggest.

  2. Robust quantitative scratch assay

    PubMed Central

    Vargas, Andrea; Angeli, Marc; Pastrello, Chiara; McQuaid, Rosanne; Li, Han; Jurisicova, Andrea; Jurisica, Igor

    2016-01-01

    The wound healing assay (or scratch assay) is a technique frequently used to quantify the dependence of cell motility—a central process in tissue repair and evolution of disease—subject to various treatments conditions. However processing the resulting data is a laborious task due its high throughput and variability across images. This Robust Quantitative Scratch Assay algorithm introduced statistical outputs where migration rates are estimated, cellular behaviour is distinguished and outliers are identified among groups of unique experimental conditions. Furthermore, the RQSA decreased measurement errors and increased accuracy in the wound boundary at comparable processing times compared to previously developed method (TScratch). Availability and implementation: The RQSA is freely available at: http://ophid.utoronto.ca/RQSA/RQSA_Scripts.zip. The image sets used for training and validation and results are available at: (http://ophid.utoronto.ca/RQSA/trainingSet.zip, http://ophid.utoronto.ca/RQSA/validationSet.zip, http://ophid.utoronto.ca/RQSA/ValidationSetResults.zip, http://ophid.utoronto.ca/RQSA/ValidationSet_H1975.zip, http://ophid.utoronto.ca/RQSA/ValidationSet_H1975Results.zip, http://ophid.utoronto.ca/RQSA/RobustnessSet.zip, http://ophid.utoronto.ca/RQSA/RobustnessSet.zip). Supplementary Material is provided for detailed description of the development of the RQSA. Contact: juris@ai.utoronto.ca Supplementary information: Supplementary data are available at Bioinformatics online. PMID:26722119

  3. Plasma-polymerized coating for polycarbonate: Single-layer, abrasion resistant, and antireflection

    NASA Technical Reports Server (NTRS)

    Wydeven, Theodore

    1991-01-01

    Plasma-polymerized vinyl trimethoxy silane films were deposited on transparent polycarbonate substrates. The adherent, clear films protected the substrates from abrasion and also served as antireflection coatings. Post-treatment of the vinyl trimethoxy silane films in an oxygen glow discharge further improved their abrasion resistance. The coatings were characterized by elemental analysis of the bulk, ESCA analysis of the surface, transmission, thickness, abrasion resistance, haze, and adhesion. This patented process is currently used by the world's largest manufacturers of non-prescription sunglasses to protect the plastic glasses from scratching and thereby to increase their useful lifetime.

  4. Scratch-Resistant Lenses

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Lewis Research Center developed a process for achieving diamond- hard coatings for aerospace systems. The technique involves coating the material with a film of diamond-like carbon (DLC) using direct ion deposition. An ion generator creates a stream of ions from a hydrocarbon gas source; the carbon ions impinge directly on the target substrate and 'grow' into a thin DLC film. In 1988, Air Products and Chemicals, Inc. received a license to the NASA patent. Diamonex, an Air Products spinoff company, further developed the NASA process to create the DiamondHard technology used on the Bausch & Lomb Ray- Ban Survivors sunglasses. The sunglasses are scratch-resistant and shed water more easily, thus reducing spotting.

  5. Abrasion resistance of medical glove materials.

    PubMed

    Walsh, Donna L; Schwerin, Matthew R; Kisielewski, Richard W; Kotz, Richard M; Chaput, Maria P; Varney, George W; To, Theresa M

    2004-01-15

    Due to the increasing demand for nonlatex medical gloves in the health-care community, there is a need to assess the durability of alternative glove materials. This study examines durability characteristics of various glove materials by abrasion resistance testing. Natural rubber latex (latex), polyvinyl chloride (vinyl), acrylonitrile butadiene (nitrile), polychloroprene (neoprene), and a styrene-ethylene/butylene-styrene block copolymer (SEBS) were tested. All test specimens, with the exception of the vinyl, were obtained from surgical gloves. Unaged out-of-the-box specimens as well as those subjected to various degrees of artificial aging were included in the study. After the abrasion sequence, the barrier integrity of the material was assessed through the use of a static leak test. Other traditional tests performed on these materials were viral penetration to validate the abrasion data and tear testing for comparative purposes. The results indicate that specific glove-material performance is dependent upon the particular test under consideration. Most notably, abrasion, even in controlled nonsevere conditions, may compromise to varying degrees the barrier integrity of latex, vinyl, SEBS, nitrile, and neoprene glove materials. However, as evidenced by the results of testing three brands of neoprene gloves, the abrasion resistance of any one glove material may be significantly affected by variations in production processes. PMID:14689500

  6. Itch Relief by Mirror Scratching. A Psychophysical Study

    PubMed Central

    Helmchen, Christoph; Palzer, Carina; Münte, Thomas F.; Anders, Silke; Sprenger, Andreas

    2013-01-01

    Objective The goal of this study was to test whether central mechanisms of scratching-induced itch attenuation can be activated by scratching the limb contralateral to the itching limb when the participant is made to visually perceive the non-itching limb as the itching limb by means of mirror images. Methods Healthy participants were asked to assess the intensity of an experimentally induced itch at their right forearm while they observed externally guided scratch movements either at their right (itching) or left (non-itching) forearm which were either mirrored or not mirrored. In the first experiment, a mirror placed between the participant’s forearms was used to create the visual illusion that the participant’s itching (right) forearm was being scratched while in fact the non-itching (left) forearm was scratched. To control visibility of the left (non-mirrored) forearm, a second experiment was performed in which unflipped and flipped real-time video displays of the participant’s forearms were used to create experimental conditions in which the participant visually perceived scratching either on one forearm only, on both forearms, or no scratching at all. Results In both experiments, scratching the non-itching limb attenuated perceived itch intensity significantly and selectively in the mirror condition, i.e., when the non-itching forearm was visually perceived as the itching limb. Discussion These data provide evidence that the visual illusion that an itching limb is being scratched while in fact the non-itching limb contralateral to the itching limb is scratched, can lead to significant itch relief. This effect might be due to a transient illusionary intersensory perceptual congruency of visual, tactile and pruriceptive signals. “Mirror scratching” might provide an alternative treatment to reduce itch perception in focal skin diseases with persistent pruritus without causing additional harm to the affected skin and might therefore have significant

  7. /Scratch as a Cache: Rethinking HPC Center Scratch Storage

    SciTech Connect

    Monti, Henri; Butt, Ali R; Vazhkudai, Sudharshan S

    2009-06-01

    To sustain emerging data-intensive scientific applications, High Performance Computing (HPC) centers invest a notable fraction of their operating budget on a specialized fast storage system, scratch space, which is designed for storing the data of currently running and soon-to-run HPC jobs. Instead, it is often used as a standard file system, wherein users arbitrarily store their data, without any consideration to the center's overall performance. To remedy this, centers periodically scan the scratch in an attempt to purge transient and stale data. This practice of supporting a cache workload using a file system and disjoint tools for staging and purging results in suboptimal use of the scratch space. In this paper, we address the above issues by proposing a new perspective, where the HPC scratch space is treated as a cache, and data population, retention, and eviction tools are integrated with scratch management. In our approach, data is moved to the scratch space only when it needed, and unneeded data is removed as soon as possible. We also design a new job-workflow-aware caching policy that leverages user-supplied hints for managing the cache. Our evaluation using three-year job logs from the Jaguar supercomputer, shows that compared to the widely-used purge approach, workflow-aware caching optimizes scratch utilization by reducing the average amount of data read by 9.3%, and by reducing job scheduling delays associated with data staging, on average, by 282.0%.

  8. Surface damage behavior during scratch deformation of mineral reinforced polymer composites

    SciTech Connect

    Misra, R.D.K.; Hadal, R.; Duncan, S.J

    2004-08-16

    The surface damage behavior during scratch deformation of neat and wollastonite reinforced ethylene-propylene and polypropylene polymeric materials with significant differences in ductility was studied using electron microscopy in association with scratch deformation parameters and local crystallinity characteristics obtained from atomic force microscopy. Under identical conditions of scratch tests, the decrease in resistance to scratch damage and stress whitening of polymeric materials followed the sequence: wollastonite-reinforced polypropylene (PP-W) congruent with wollastonite-reinforced ethylene-propylene (EP-W) > neat polypropylene (PP) > neat ethylene-propylene copolymer (EP). The improved resistance to scratch damage of mineral reinforced polymeric materials is attributed to the effective reinforcement by micrometer-sized wollastonite particles that increase the tensile modulus of the polymeric materials and restrict plastic deformation of the polymer matrix. Scratching of neat and wollastonite-containing EP copolymers involved periodic parabolic scratch tracks containing voids, which transformed to distinct zig-zag scratch tracks on reinforcement with micrometric wollastonite particles. The enhanced plastic flow in neat EP is facilitated by high ductility of the material and ability to nucleate voids, while in EP-W the plastic flow is suppressed because of reinforcement effect of wollastonite. On the other hand, zig-zag periodic scratch tracks were observed in both neat PP and PP-W, but the scratch tracks were not clearly discernible on reinforcement of PP with wollastonite. The resistance to scratch deformation is discussed in terms of tensile modulus, elastic recovery, scratch hardness, and reinforcement-matrix interaction.

  9. Bites and Scratches (For Parents)

    MedlinePlus

    ... Text Size en español Mordeduras y arañazos de animal Animal bites and scratches, even minor ones, can sometimes lead to complications. Whether the animal is a family pet (in kids, most animal ...

  10. Abrasive wear of advanced structural materials

    NASA Astrophysics Data System (ADS)

    Lee, Gun-Young

    Wear of advanced structural materials, namely composites and ceramics, in abrasion has been examined in the present study. A simple physically-based model for the abrasive wear of composite materials is presented based on the mechanics and mechanisms associated with sliding wear in soft (ductile) matrix composites containing hard (brittle) reinforcement particles. The model is based on the assumption that any portion of the reinforcement that is removed as wear debris cannot contribute to the wear resistance of the matrix material. The size of this non-contributing portion of reinforcement is estimated by modeling three primary wear mechanisms, specifically plowing, cracking at the matrix/reinforcement interface or in the reinforcement, and particle removal. Critical variables describing the role of the reinforcement, such as the relative size, fracture toughness, and the nature of the matrix/reinforcement interface, are characterized by a single contribution coefficient, C. Predictions are compared with the results of experimental two-body (pin-on-drum) abrasive wear tests performed on a model aluminum particulate-reinforced epoxy-matrix composite material. In addition, the effects of post heat-treatment on the wear behavior of toughened silicon carbide (ABC-SiC) are investigated by characterizing the role of the microstructures introduced during the post annealing processes. When the annealing temperature is above 1300°C, an aluminum rich secondary phase (nano-precipitate) forms and grows inside the SiC grains. This toughened silicon carbide (ABC-SiC), annealed at temperatures ranging from 0 to 1600°C, is subjected to two- and three-body abrasions with different sizes of abrasives (3˜70 mum). The test results exhibit that the effect of nano-precipitates on wear resistance of post-annealed ABC-SiC is restricted to the abrasion with fine abrasives (3 mum), since nano-precipitates, in the range from 4 nm at 1300°C to 25 nm at 1600°C, are comparable in dimension

  11. Effect of Scratches on Pinch Welds

    SciTech Connect

    Korinko, P

    2005-10-11

    Fill stems for tritium reservoirs have stringent scratch requirements such that any indications that appear to have depth are cause for rework or rejection. A scoping study was undertaken to evaluate the effect of scratches approximately 0.0015 to 0.002 inch deep on the fitness for service and bond quality. The stems were characterized using borescope before and after welding. The four stems were welded with near optimal weld parameters, proof tested, and examined metallographically. The stems were radiographed, proof tested, and examined metallographically. The scratches did not adversely affect (1) the weld integrity based on radiography, (2) the ability to withstand the proof pressure, and (3) the weld quality based on metallographic cross-sections. Based on these limited results at a nominal weld current, the weld process is very robust. It may be able to recover from manufacturing defects and inspection anomalies worse than those expected for typical fill stem manufacturing processes; additional testing specific to each application over a range of weld heats is needed to verify applicability of these results.

  12. Coherent Backscatter Opposition Effect from Scratches on Solid Surfaces

    NASA Astrophysics Data System (ADS)

    Hapke, B. W.; Piatek, J. L.; Nelson, R. M.; Smythe, W. D.; Hale, A. S.

    2003-05-01

    Shepard and Arvidson [1] discovered that the solid surfaces of rocks exhibit an opposition effect. We have measured the phase curve of a natural surface of a piece of solid basalt between 0.05 and 5 degrees in circularly polarized light using the JPL long arm goniometer and confirmed that it has an opposition effect. The circular polarization ratio (CPR) increased with decreasing phase angle, consistent with a coherent backscatter opposition effect (CBOE) Recent laboratory investigations of the CBOE in planetary regolith analogs [2,3,4] have revealed that the width of the peak is remarkably insensitive to particle size, in strong contrast to theoretical expectations. We have hypothesized that one of the reasons for this might be that multiple scattering between irregularities, such as scratches, on the surfaces of a particle could cause coherent backscatter, in addition to scattering between particles. To test this hypothesis we ground the surface of a piece of plate glass with 5 micrometer abrasive and measured its phase curve. As the phase angle decreases, the intensity increases and the CPR decreases, consistent with specular reflection. However, near zero phase there is a nonlinear rise about 2 degrees wide superimposed on the linear specular peak accompanied by an increase in CPR, showing that coherent backscatter is occuring. A piece of commercial diffusing glass exhibited the same phenomena. These results support our hypothesis and also provide a possible explanation for the observations of opposition effects from the solid surfaces of rocks. This research was supported by a grant from NASA's PGG Program References cited: [1] Shepard and Arvidson, Icarus, 141, 172-178 (1999). [2] Nelson et al, Icarus, 147, 545-558 (2000). [3] Nelson et al, Planet. Space Sci., 50, 849-856 (2002). [4] Piatek et al, Abstract, DPS Conference (2003).

  13. Valve for abrasive material

    DOEpatents

    Gardner, Harold S.

    1982-01-01

    A ball valve assembly for controlling the flow of abrasive particulates including an enlarged section at the bore inlet and an enlarged section at the bore outlet. A refractory ceramic annular deflector is positioned in each of the enlarged sections, substantially extending the useful life of the valve.

  14. Cat scratch disease: The story continues

    PubMed Central

    Opavsky, Mary Anne

    1997-01-01

    OBJECTIVE: To present a perspective on the current state of knowledge of cat scratch disease (CSD), including the evidence for Bartonella henselae as the etiological agent, epidemiological and clinical characteristics of the disease, available diagnostic tests and current therapeutic options. DATA SOURCES: MEDLINE search of the literature published from 1966 to 1995 using ‘cat scratch disease’, ‘Bartonella henselae’, ‘Rochalimaea henselae’ as key words and bibliographies of selected papers. DATA EXTRACTION: Selected studies reporting data on etiology, epidemiology, clinical characteristics, diagnosis and therapy of CSD were evaluated. DATA SYNTHESIS AND CONCLUSIONS: Evidence accumulated to date supports B henselae as the etiological agent of CSD. The most significant risk factors for CSD are being licked on the face, scratched or bitten by a kitten and owning a kitten with fleas. Available serological tests can confirm classic CSD and identify B henselae as the cause of more atypical presentations, such as fever of unknown origin, granulomatous hepatitis, encephalitis and osteomyelitis. Symptomatic management is appropriate for isolated lymphadenopathy caused by CSD in healthy individuals; however, antibiotic therapy may be indicated for patients with more severe manifestations of the disease and immunocompromised hosts. Further study of CSD, in particular the epidemiology and therapy, is warranted. A better understanding of the pathogenesis of B henselae infection will have important implications in both immunocompetent and immunocompromised individuals. PMID:22514476

  15. Field Variable Associations With Scratch Orientation-Dependence of UHMWPE Wear: A Finite Element Analysis

    PubMed Central

    Paul, Matthew C.; Glennon, Liam P.; Baer, Thomas E.; Brown, Thomas D.

    2008-01-01

    Background Scratches on the metal bearing surface of metal-on-polyethylene total joint replacements have been found to appreciably accelerate abrasive/adhesive wear of polyethylene, and constitute a source of the considerable variability of wear rate seen within clinical cohorts. Scratch orientation with respect to the local direction of relative surface sliding is presumably a factor affecting instantaneous debris liberation during articulation. Method of Approach A three-dimensional local finite element model was developed of orientation-specific polyethylene articulation with a scratched metal counterface, to explore continuum-level stress/strain parameters potentially correlating with the orientation dependence of scratch wear in a corresponding physical experiment. Results Computed maximum stress values exceeded the yield strength of ultra-high molecular weight polyethylene (UHMWPE) for all scratch orientations, but did not vary appreciably among scratch orientations. Two continuum-level parameters judged most consistent overall with the direction dependence of experimental wear were: (1) cumulative compressive total normal strain in the direction of loading, and (2) maximum instantaneous compressive total normal strain transverse to the sliding direction. Conclusions Such stress/strain metrics could be useful in global computational models of wear acceleration, as surrogates to incorporate anisotropy of local metal surface roughening. PMID:19045548

  16. Mechanical properties of pulsed laser-deposited hydroxyapatite thin films implanted at high energy with N + and Ar + ions. Part II: nano-scratch tests with spherical tipped indenter

    NASA Astrophysics Data System (ADS)

    Pelletier, H.; Nelea, V.; Mille, P.; Muller, D.

    2004-02-01

    In this study we report a method to improve the adherence of hydroxyapatite (HA) thin films, using an ion beam implantation treatment. Crystalline HA films were grown by pulsed laser deposition technique (PLD), using an excimer KrF * laser. The films were deposited at room temperature in vacuum on Ti-5Al-2.5Fe alloy substrates previously coated with a ceramic TiN buffer layer and then annealed in ambient air at (500-600) °C. After deposition the films were implanted with N + and Ar + ions accelerated at high energy (1-1.5 MeV range) at a fixed dose of 10 16 cm -2. The intrinsic mechanical resistance and adherence to the TiN buffer layer of the implanted HA films have been evaluated by nano-scratch tests. We used for measurements a spherical indenter with a tip radius of 5 μm. Different scratch tests have been performed on implanted and unimplanted areas of films to put into evidence the effects of N + and Ar + ion implantation process on the films properties. Results show an enhancement of the dynamic mechanical properties in the implanted zones and influence of the nature of the implanted species. The best results are obtained for films implanted with nitrogen.

  17. Sowing simulation tests of a pneumatic drill equipped with systems aimed at reducing the emission of abrasion dust from maize dressed seed.

    PubMed

    Biocca, Marcello; Conte, Elisa; Pulcini, Patrizio; Marinelli, Enzo; Pochi, Daniele

    2011-01-01

    The utilization of dressed seed for spring sowing is a widespread practice to control some pests with reduced doses of chemical products. However some insecticides employed in maize seed dressing, namely belonging to the neonicotinoid family and fipronil, have been claimed to play a role in the decline of honeybees (Apis mellifera L.). Pneumatic drills used in maize sowing are charged with contributing to the dispersion of the abrasion dust produced by dressed seeds, favoring the contamination of the honeybee habitat. Different devices similar to air deflectors have been introduced on pneumatic drills in order to reduce dust drift. During previous field tests carried out by the authors during recent years reduction of dust concentration both in the air and at soil surface has been shown as a consequence of their application. As field tests are affected by the variability of environmental parameters (namely wind speed and direction) the results are not always reliable, comparable and of a general validity. This paper refers to a sowing simulation test system in which pneumatic drills can be tested at a fixed point under controlled conditions of the main environmental parameters. In the test area, protected by external influences, artificial wind conditions are created by means of a fan. The drill, suitably placed in the test area, operates the seed distribution "sur place" by means of an electric engine connected to the drill's driving wheel. A 22.5 m long sampling area, leeward with respect to the drill position, has been identified. Along the sampling area a series of Petri dishes has been placed, with the aim of capturing the depositing dust and providing the concentration of the active ingredients (a.i.) at ground level. At the same time, three air samplers with PTFE diskette filters have been used for the detection of the a.i. The test system has been used for the test of a pneumatic drill, equipped with and without air deflectors, using maize seed dressed with

  18. Abrasion resistant heat pipe

    DOEpatents

    Ernst, Donald M.

    1984-10-23

    A specially constructed heat pipe for use in fluidized bed combustors. Two distinct coatings are spray coated onto a heat pipe casing constructed of low thermal expansion metal, each coating serving a different purpose. The first coating forms aluminum oxide to prevent hydrogen permeation into the heat pipe casing, and the second coating contains stabilized zirconium oxide to provide abrasion resistance while not substantially affecting the heat transfer characteristics of the system.

  19. Abrasion resistant heat pipe

    DOEpatents

    Ernst, D.M.

    1984-10-23

    A specially constructed heat pipe is described for use in fluidized bed combustors. Two distinct coatings are spray coated onto a heat pipe casing constructed of low thermal expansion metal, each coating serving a different purpose. The first coating forms aluminum oxide to prevent hydrogen permeation into the heat pipe casing, and the second coating contains stabilized zirconium oxide to provide abrasion resistance while not substantially affecting the heat transfer characteristics of the system.

  20. Abrasion of 6 dentifrices measured by vertical scanning interference microscopy

    PubMed Central

    PASCARETTI-GRIZON, Florence; MABILLEAU, Guillaume; CHAPPARD, Daniel

    2013-01-01

    Objectives The abrasion of dentifrices is well recognized to eliminate the dental plaque. The aims of this study were to characterize the abrasive powders of 6 dentifrices (3 toothpastes and 3 toothpowders) and to measure the abrasion on a test surface by Vertical Scanning Interference microscopy (VSI). Material and Methods Bright field and polarization microscopy were used to identify the abrasive particles on the crude dentifrices and after prolonged washes. Scanning electron microscopy and microanalysis characterized the shape and nature of the particles. Standardized and polished blocks of poly(methylmethacrylate) were brushed with a commercial electric toothbrush with the dentifrices. VSI quantified the mean roughness (Ra) and illustrated in 3D the abraded areas. Results Toothpastes induced a limited abrasion. Toothpowders induced a significantly higher roughness linked to the size of the abrasive particles. One powder (Gencix® produced a high abrasion when used with a standard testing weight. However, the powder is based on pumice particles covered by a plant homogenate that readily dissolves in water. When used in the same volume, or after dispersion in water, Ra was markedly reduced. Conclusion Light and electron microscopy characterize the abrasive particles and VSI is a new tool allowing the analysis of large surface of abraded materials. PMID:24212995

  1. Cat scratch disease

    MedlinePlus

    ... way to detect the infection caused by these bacteria. The results of this test must be considered along with other information from your medical history, lab tests, or biopsy. A lymph node biopsy ...

  2. A magnifying scratch-gage force transducer

    NASA Technical Reports Server (NTRS)

    Scott, C. E.

    1969-01-01

    Single-component scratch-gage transducer incorporates a unique motion magnification scheme to increase the magnitude of the load measuring scratch approximately 15 times over that of conventional models. It is small, load carrying and high in natural frequency.

  3. Topical treatment with basic fibroblast growth factor promotes wound healing and barrier recovery induced by skin abrasion.

    PubMed

    Nakamizo, S; Egawa, G; Doi, H; Natsuaki, Y; Miyachi, Y; Kabashima, K

    2013-01-01

    It has been reported that basic fibroblast growth factor (bFGF) promotes the healing of skin ulceration by inducing fibroblast proliferation, yet the role of bFGF on epidermal barrier function, especially from the perspective of scratch-induced skin abrasion, remains unknown. To this end, we initially developed an epidermal abrasion mouse model induced by scratching with a stainless-steel wire brush, and examined the effects of bFGF on the wound healing induced by skin abrasion. This procedure induced a significant elevation of transepidermal water loss (TEWL) in a scratch-count-dependent manner. This elevated TEWL was significantly decreased following topical application of bFGF to the skin. In addition, bFGF increased the expression of Ki67 in keratinocytes following mechanical scratching. These results suggest that bFGF enhances keratinocyte proliferation, which, in turn, repairs the skin barrier disruption and wounds caused by scratching in mice. Consistently, bFGF stimulated proliferation of normal human epidermal keratinocytes (NHEK). Intriguingly, the effect of bFGF and other growth factors on NHEK proliferation was additive. However, high cell density diminished the effect of bFGF on NHEK proliferation. This particular result can be explained by our observation that FGF receptor mRNA expression in NHEK was low under conditions of high cell density. Our findings suggest that bFGF stimulates keratinocyte proliferation, especially in a lower cell density environment, to repair skin wound in accord with skin barrier recovery. PMID:23108135

  4. Solidification Structure and Abrasion Resistance of High Chromium White Irons

    SciTech Connect

    Dogan, O.N.; Hawk, J.A.; Laird, George, II

    1997-06-01

    Superior abrasive wear resistance, combined with relatively low production costs, makes high Cr white cast irons (WCIs) particularly attractive for applications in the grinding, milling, and pumping apparatus used to process hard materials. Hypoeutectic, eutectic, and hypereutectic cast iron compositions, containing either 15 or 26 wt pct chromium, were studied with respect to the macrostructural transitions of the castings, solidification paths, and resulting microstructures when poured with varying superheats. Completely equiaxed macrostructures were produced in thick section castings with slightly hypereutectic compositions. High-stress abrasive wear tests were then performed on the various alloys to examine the influence of both macrostructure and microstructure on wear resistance. Results indicated that the alloys with a primarily austenitic matrix had a higher abrasion resistance than similar alloys with a pearlitic/bainitic matrix. Improvement in abrasion resistance was partially attributed to the ability of the austenite to transform to martensite at the wear surface during the abrasion process.

  5. Solidification structure and abrasion resistance of high chromium white irons

    SciTech Connect

    Dogan, O.N.; Hawk, J.A.; Laird, G. II

    1997-06-01

    Superior abrasive wear resistance, combined with relatively low production costs, makes high Cr white cast irons (WCIs) particularly attractive for applications in the grinding, milling, and pumping apparatus used to process hard materials. Hypoeutectic, eutectic, and hypereutectic cast iron compositions, containing either 15 or 26 wt pct chromium, were studied with respect to the macrostructural transitions of the castings, solidification paths, and resulting microstructures when poured with varying superheats. Completely equiaxed macrostructures were produced in thick section castings with slightly hypereutectic compositions. High-stress abrasive wear tests were then performed on the various alloys to examine the influence of both macrostructure and microstructure on wear resistance. Results indicated that the alloys with a primarily austenitic matrix had a higher abrasion resistance than similar alloys with a pearlitic/bainitic matrix. Improvement in abrasion resistance was partially attributed to the ability of the austenite to transform to martensite at the wear surface during the abrasion process.

  6. Learning Computer Science Concepts with Scratch

    ERIC Educational Resources Information Center

    Meerbaum-Salant, Orni; Armoni, Michal; Ben-Ari, Mordechai

    2013-01-01

    Scratch is a visual programming environment that is widely used by young people. We investigated if Scratch can be used to teach concepts of computer science (CS). We developed learning materials for middle-school students that were designed according to the constructionist philosophy of Scratch and evaluated them in a few schools during two…

  7. Abrasion protection in process piping

    SciTech Connect

    Accetta, J.

    1996-07-01

    Process piping often is subjected to failure from abrasion or a combination of abrasion and corrosion. Abrasion is a complex phenomenon, with many factors involved to varying degrees. Hard, mineral based alumina ceramic and basalt materials are used to provide protection against abrasion in many piping systems. Successful life extension examples are presented from many different industries. Lined piping components require special attention with regard to operating conditions as well as design and engineering considerations. Economic justification involves direct cost comparisons and avoided costs.

  8. Abrasion resistant composition

    DOEpatents

    Fischer, Keith D; Barnes, Christopher A; Henderson, Stephen L

    2014-05-13

    A surface covering composition of abrasion resistant character adapted for disposition in overlying bonded relation to a metal substrate. The surface covering composition includes metal carbide particles within a metal matrix at a packing factor of not less than about 0.6. Not less than about 40 percent by weight of the metal carbide particles are characterized by an effective diameter in the range of +14-32 mesh prior to introduction to the metal matrix. Not less than about 3 percent by weight of the metal carbide particles are characterized by an effective diameter of +60 mesh prior to introduction to the metal matrix.

  9. The effects of abrasives on electrical submersible pumps

    SciTech Connect

    Wilson, B.L. )

    1990-06-01

    The electrical submersible pump (ESP) is a high-speed rotating device. Its operational life in oil wells can depend on the type and quantities of abrasives present in the produced fluid. This paper reports on a set of experiments performed in a specialized abrasive test loop. In the test, the size and quantity of abrasives were varied along with flow rate through the pump. This paper also examines recent literature on sand production and explores some of the practical problems in sand measurement.

  10. Cat scratch disease from a domestic dog.

    PubMed

    Chen, Tun-Chieh; Lin, Wei-Ru; Lu, Po-Liang; Lin, Chun-Yu; Chen, Yen-Hsu

    2007-02-01

    Cat scratch disease (CSD), caused by Bartonella henselae, is a zoonosis and characterized by self-limited lymphadenopathy. It is transmitted commonly by scratch or bite from cats or kitten. We report an unusual case of CSD caused by a domestic dog scratch that we believe is the first report in Taiwan. A 23-year-old healthy woman developed cervical lymphadenopathy, mild fever, headache, and malaise 3 days after dog scratch. Her symptoms improved after azithromycin treatment. Serology proved B. henselae infection. The owners of a domestic dog might be at risk of "cat" scratch disease. PMID:17493900

  11. Nanoindentation and scratch studies on magnetron sputtered Ti thin films.

    PubMed

    Kataria, S; Ramaseshan, R; Dash, S; Tyagi, A K

    2009-09-01

    Ti thin films sputter deposited on D9 steel at two different temperatures were studied for their mechanical behavior under static and sliding contact conditions using nanoindentation and scratch tests. The film hardness measured at the surface of the coatings exhibited a value of 2.5 GPa, for both conditions. From the scratch test, it is understood that coatings deposited at 200 degrees C substrate temperature showed superior adhesion strength. Critical load to failure for these coatings was evaluated at 2 N. PMID:19928247

  12. Scratch direction and threshold force in nanoscale scratching using atomic force microscopes

    NASA Astrophysics Data System (ADS)

    Tseng, Ampere A.; Kuo, Chung-Feng Jeffrey; Jou, Shyankay; Nishimura, Shinya; Shirakashi, Jun-ichi

    2011-09-01

    The nanoscaled tip in an AFM (atomic force microscope) has become an effective scratching tool for material removing in nanofabrication. In this article, the characteristics of using a diamond-coated pyramidal tip to scratch Ni-Fe thin film surfaces was experimentally investigated with the focus on the evaluation of the influence of the scratch or scan direction on the final shape of the scratched geometry as well as the applied scratch force. Results indicated that both the scratched profile and the scratch force were greatly affected by the scratch direction. It has been found that, to minimize the formation of protuberances along the groove sides and to have a better control of the scratched geometry, the tip face should be perpendicular to the scratching direction, which is also known as orthogonal cutting condition. To demonstrate the present findings, three groove patterns have been scratched with the tip face perpendicular to the scratching direction and very little amount of protuberances was observed. The threshold scratch force was also predicted based on the Hertz contact theory. Without considering the surface friction and adhesive forces between the tip and substrate, the threshold force predicted was twice smaller than the measurement value. Finally, recommendations for technical improvement and research focuses are provided.

  13. Wheel Abrasion Experiment Conducted on Mars

    NASA Technical Reports Server (NTRS)

    Ferguson, Dale C.

    1998-01-01

    Sojourner rover showing Lewis' wheel abrasion experiment. The Mars Pathfinder spacecraft soft-landed on Mars on July 4, 1997. Among the many experiments on its small Sojourner rover are three technology experiments from the NASA Lewis Research Center, including the Wheel Abrasion Experiment (WAE). The WAE was designed, built, delivered, and operated on Mars by a team of engineers and scientists from Lewis' Photovoltaics and Space Environments Branch. This experiment collected data to assess wheel surface wear on the Sojourner. It used a specially designed rover wheel, with thin films (200 to 1000 angstroms) of aluminum, nickel, and platinum deposited on black, anodized aluminum strips attached to the rover's right center wheel. As the wheel spun in the Martian soil, a photovoltaic sensor monitored changes in film reflectivity. These changes indicated abrasion of the metal films by Martian surface material. Rolling wear data were accumulated by the WAE. Also, at frequent intervals, all the rover wheels, except the WAE test wheel, were locked to hold the rover stationary while the test wheel alone was spun and dug into the Martian regolith. These tests created wear conditions more severe than simple rolling. The WAE will contribute substantially to our knowledge of Martian surface characteristics. Marked abrasion would indicate a surface composed of hard, possibly sharply edged grains, whereas lack of abrasion would suggest a somewhat softer surface. WAE results will be correlated with ground simulations to determine which terrestrial materials behave most like those on Mars. This knowledge will enable a deeper understanding of erosion processes on Mars and the role they play in Martian surface evolution. Preliminary results show that electrostatic charging of the rover wheels sometimes caused dust to accumulate on the WAE wheel, making interpretation of the reflectance data problematic. If electrostatic charging is the mechanism for dust attraction, this indicates

  14. Resistance of dentin coating materials against abrasion by toothbrush.

    PubMed

    Gando, Iori; Ariyoshi, Meu; Ikeda, Masaomi; Sadr, Alireza; Nikaido, Toru; Tagami, Junji

    2013-01-01

    Thin-film coating of root dentin surface by all-in-one adhesives has been shown to be an effective option to prevent root surface caries. The purpose of this study was to investigate the wear resistance against toothbrush abrasion of two all-in-one coating materials; Shield Force (SF) and Hybrid Coat (HC). Bovine dentin surfaces were covered with one of the coating materials; SF or HC. After storage in water for 24 h, the testing surface was subjected to the toothbrush abrasion test up to 50,000 cycles either in water or toothpaste slurry. The remaining thickness of the coating material was measured using SEM. Toothpaste slurry significantly increased rate of tooth brush abrasion of the coating materials. While SF and HC wore at a similar pace under toothbrush abrasion, SF had a thicker coat and could protect dentin longer, up to 50,000 cycles. PMID:23370872

  15. Effects of interlayers on the scratch adhesion performance of ultra-thin films of copper and gold on silicon substrates

    SciTech Connect

    McAdams, S.D.; Tsui, T.Y.; Pharr, G.M.; Oliver, W.C.

    1995-02-01

    Scratch testing has long been used to assess the adhesion of a film to its substrate. As film thicknesses have decreased, the need for greater precision and sensitivity in the scratch testing apparatus has increased. To this end, a nanoindenter was modified to make finely controlled, low-load scratches. Scratches at various loads and two orientations of a Berkovich scratching diamond were made in films of 100 nm of gold and 200 nm of copper, each on single crystal silicon. For each film type, samples with no interlayer, with an SiO{sub 2} interlayer, and with a TiW on SiO{sub 2} interlayer were tested. The scratch morphology was found to vary in a regular way with load, diamond orientation and interlayer material.

  16. Scratching Responses to Epidermal Injury in C57BL/6, DBA/2, BALB/c, and CD1 Mice.

    PubMed

    Sargent, Jennifer L; Löhr, Christiane V; Diggs, Helen E

    2016-01-01

    Whereas early investigations into ulcerative dermatitis (UD) focused on the possibility of a primary dermatopathology, several recent studies have advocated scratching behavior as a primary driver for UD. The aim of this study was to assess whether B6 mice exhibit excessive scratching under resting conditions or when provoked by epidermal barrier disruption. We hypothesized that B6 mice would exhibit more spontaneous scratching behavior and that B6 mice would be more pruritic after mild epidermal barrier injury compared with the other strains and stock tested. The behavior of the retired breeder female C57BL/6J, DBA/2J, BALB/cByJ, and Crl:CD1 mice was videotaped for 60 min. Behavior filming occurred at 17:15 and at 07:00 the next morning prior to (baseline) and after tape-stripping to initiate epidermal barrier disruption. Scratching duration was recorded as brief (less than 3 s) or prolonged (3 s or longer), on the basis of observations during a pilot study. In contrast to the hypothesis, B6 mice did not scratch significantly more frequently, have more long-duration scratching events, nor have a higher median scratching duration of prolonged scratching as compared with the other types of mice tested. In fact, B6 mice showed the lowest average scratching frequency and duration under both conditions. B6 mice demonstrated increased scratching behavior after epidermal barrier disruption, but the increased scratching did not surpass the rate or duration of scratching in the other types of mice tested. These findings do not support the idea that a strain-related tendency toward exaggerated scratching behavior under resting or epidermal barrier disruption conditions predisposes B6 mice to UD. PMID:27298245

  17. Dentifrice fluoride and abrasivity interplay on artificial caries lesions.

    PubMed

    Nassar, Hani M; Lippert, Frank; Eckert, George J; Hara, Anderson T

    2014-01-01

    Incipient caries lesions on smooth surfaces may be subjected to toothbrushing, potentially leading to remineralization and/or abrasive wear. The interplay of dentifrice abrasivity and fluoride on this process is largely unknown and was investigated on three artificially created lesions with different mineral content/distribution. 120 bovine enamel specimens were randomly allocated to 12 groups (n = 10), resulting from the association of (1) lesion type [methylcellulose acid gel (MeC); carboxymethylcellulose solution (CMC); hydroxyethylcellulose gel (HEC)], (2) slurry abrasive level [low (REA 4/ RDA 69); high (REA 7/RDA 208)], and (3) fluoride concentration [0/275 ppm (14.5 mM) F as NaF]. After lesion creation, specimens were brushed in an automated brushing machine with the test slurries (50 strokes 2×/day). Specimens were kept in artificial saliva in between brushings and overnight. Enamel surface loss (SL) was determined by optical profilometry after lesion creation, 1, 3 and 5 days. Two enamel sections (from baseline and post-brushing areas) were obtained and analyzed microradiographically. Data were analyzed by analysis of variance and Tukey's tests (α = 5%). Brushing with high-abrasive slurry caused more SL than brushing with low-abrasive slurry. For MeC and CMC lesions, fluoride had a protective effect on SL from day 3 on. Furthermore, for MeC and CMC, there was a significant mineral gain in the remaining lesions except when brushed with high-abrasive slurries and 0 ppm F. For HEC, a significant mineral gain took place when low-abrasive slurry was used with fluoride. The tested lesions responded differently to the toothbrushing procedures. Both slurry fluoride content and abrasivity directly impacted SL and mineral gain of enamel caries lesions. PMID:24993884

  18. Abrasives in snuff?

    PubMed

    Dahl, B L; Stølen, S O; Oilo, G

    1989-08-01

    The purpose of this study was to determine and calculate the inorganic contents of four brands of snuff. Visual inspection of wet snuff showed fairly large, yellow crystal-like particles. Scanning electron microscopy and X-ray dispersive (EDX) analyses were used to study both wet snuff and ashes of snuff, whereas light emission spectrography was used to determine elements in the ashes. The crystal-like particles did not dissolve in distilled water or in ethanol heated to 60 degrees C. EDX analyses showed that most elements remained in the particles after washing. The total weight percentage of inorganic material in snuff was calculated after burning dried snuff until constant weight was obtained. The ashes of snuff did not contain any crystal-like particles but consisted of a small-grained amorphous mass. The following elements were detected: Ag, Al, Ba, Ca, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, P, Pb, Si, Sr, Ti, Va, and Zr. Other elements such as rare earths were not searched for. The weight percentage of inorganic elements ranged between 12.35 +/- 0.69 and 20.95 +/- 0.81. Provided snuff is used in the same manner as chewing tobacco, and some people admit to doing so, there is a risk that its relatively high contents of inorganic material and heavily soluble salts may be conducive to excessive abrasion of teeth and restorations. PMID:2782061

  19. Effect of Adhesion and Contact Geometry on Scratch Behavior of Polyvinyl Alcohol

    NASA Astrophysics Data System (ADS)

    Yoder, Karl; Xia, Xinyun; Gerberich, William

    2000-03-01

    The mechanical response of a material to single-point scratch loading is complex, with contributions from contact geometry, imposed deformation rate, thermomechanical interactions, and constitutive properties. Additionally, the effect of adhesion between scratch tip and specimen is an important, yet poorly understood, variable in deformation response. In particular the effects of adhesion and contact geometry on the mode of deformation and damage morphology are difficult to experimentally separate. Using a Hysitron Triboindenter, which can perform both nanoindentation and nanoscratch tests, in a controlled environmental chamber, the effect of adhesion on scratch response of polyvinyl alcohol is investigated. In addition, by using four different diamond tips, the role of contact geometry as it pertains to adhesion and scratch response is investigated. This talk presents the effects of contact geometry and relative humidity on stylus-PVOH adhesion, and subsequent scratch deformation response in an attempt to elucidate the role played by adhesion.

  20. Evaluation of particles released from single-wall carbon nanotube/polymer composites with or without thermal aging by an accelerated abrasion test.

    PubMed

    Jiang, Lin; Kondo, Akira; Shigeta, Masahiro; Endoh, Shigehisa; Uejima, Mitsugu; Ogura, Isamu; Naito, Makio

    2014-01-01

    To provide data required for assessing the environmental health and safety risks of nanocomposites, abrasion-induced particle release from single-wall carbon nanotube (SWCNT)/polymer composites with or without thermal aging were evaluated by a shot blast system. First, overall composite weight loss (i.e., overall particle release) as a result of shot blasting was measured. Incorporating 5 wt% SWCNTs in polystyrene (PS) matrix was observed to reduce overall particle release by approximately 30% compared with pure PS. Heat treatment of the 5 wt% SWCNT/PS composites at 100°C for 10 days induced very slight change in overall particle release due to shot blasting. However, heat treatment at 350°C for 1 hr greatly deteriorated the abrasion resistance of the composites, enhancing overall particle release. Second, to verify the existence and form of SWCNTs released from the composites, released particles were observed by electron microscopy. Micron-sized particles with protruding SWCNTs and submicron-sized SWCNT clusters were observed in the particles released from the composites. Heat treatment of the composites at 350°C for 1 hr enhanced SWCNT release, which mainly formed clusters or rope-like bundles. PMID:24628695

  1. The Scratch Programming Language and Environment

    ERIC Educational Resources Information Center

    Maloney, John; Resnick, Mitchel; Rusk, Natalie; Silverman, Brian; Eastmond, Evelyn

    2010-01-01

    Scratch is a visual programming environment that allows users (primarily ages 8 to 16) to learn computer programming while working on personally meaningful projects such as animated stories and games. A key design goal of Scratch is to support self-directed learning through tinkering and collaboration with peers. This article explores how the…

  2. Development of Abrasion-Resistant Coating for Solar Reflective Films. Cooperative Research and Development Final Report, CRADA Number CRD-07-247

    SciTech Connect

    Gray, Matthew

    2015-10-01

    The purpose of this CRADA is to develop an abrasion-resistant coating, suitable for use on polymeric-based reflective films (e.g., the ReflecTech reflective film), that allows for improved scratch resistance and enables the use of aggressive cleaning techniques (e.g., direct contact methods like brushing) without damaging the specular reflectance properties of the reflective film.

  3. Material Removal and Specific Energy in the Dynamic Scratching of Gamma Titanium Aluminides

    SciTech Connect

    Wang, Hong; Lin, Hua-Tay; Wereszczak, Andrew A

    2006-11-01

    Mechanical responses of three gamma titanium aluminides (TiAls) (denoted as Alloy A, Alloy B and Alloy C) subjected to dynamic scratching were studied by using a single-grit pendulum (rotating) scratch tester. The maximum depth of groove was ~ 0.07 mm, and the scratch velocity used was ~ 1.0 m/s. Normal and tangential forces were monitored. The material removal mechanisms were examined using a scanning electron microscope (SEM) and the scratches were measured by using a laser profilometer. The mechanical properties of the tested TiAls were characterized by the instantaneous specific energy, scratch resistance and scratch hardness as related to the depth of groove. Extensive thermal softening was observed in the dynamic scratch of the tested TiAls, which facilitated both the detachments of developing chips and the pile-ups of materials on side ridges. Sizable fractures were observed in the transverse direction on the tested TiAls; these fractures tended to participate in the chip formation, depending on the microstructure of the TiAl and the size of the scratch groove. Specific energy and scratch hardness are depth-dependent to various degrees for the tested TiAls. The materiel removal might be subjected to different mechanisms, but the overall response of materials can be effectively characterized by the HEM (Hwang, Evans and Malkin) model and the PSR (proportional specimen resistance) model. The obtained depth-independent specific energy and scratch hardness can be used to screen the candidate materials for the specific purpose depending on whether the application is scratch-dominant or impact-dominant. Among the three tested TiAls, the TiAl with larger colony or grain size exhibits a stronger capability of energy dissipation in the material loss or material removal (higher depth-independent specific energy), while the TiAl with smaller colony size show a higher resistance against the indentation (higher depth-independent scratch hardness). The observations and

  4. Material Removal and Specific Energy in the Dynamic Scratching of Gamma Titanium Aluminides

    SciTech Connect

    Wang, H.; Lin, H.-T.; Wereszczak, A.A.

    2006-11-30

    Mechanical responses of three gamma titanium aluminides (TiAls) (denoted as Alloy A, Alloy B and Alloy C) subjected to dynamic scratching were studied by using a single-grit pendulum (rotating) scratch tester. The maximum depth of groove was {approx} 0.07 mm, and the scratch velocity was {approx} 1.0 m/s. Normal and tangential forces were monitored. The material removal mechanisms were examined using a scanning electron microscope (SEM) and the scratches were measured by using a laser profilometer. The mechanical properties of the tested TiAls were characterized by the instantaneous specific energy, scratch resistance and scratch hardness as related to the groove depth. Extensive thermal softening was observed in the dynamic scratch test of the TiAls, which facilitated both the detachment of developing chips and pile-up of material on side ridges. Sizable fractures were observed in the transverse direction in the tested TiAls; these fractures tended to participate in the chip formation, depending on the microstructure of the TiAl and the size of the scratch groove. Specific energy and scratch hardness are depth-dependent to various degrees for the TiAls tested. The material removal might be subjected to different mechanisms, but the overall material response can be effectively characterized by the HEM (Hwang, Evans and Malkin) model and the PSR (proportional specimen resistance) model. The depth-independent specific energy and scratch hardness can be used to screen candidate materials for the applications that are scratch-dominated versus impact-dominated. Among the three tested TiAls, the TiAl with larger colony or grain size exhibits a stronger capability of energy dissipation during material removal (higher depth-independent specific energy), while the TiAl with smaller colony size shows a higher resistance to indentation (higher depth-independent scratch hardness). The observations and conclusions in this study can serve as a base line for the further

  5. Sleep Related Scratching: A Distinct Parasomnia?

    PubMed Central

    Nigam, Gaurav; Riaz, Muhammad; Hershner, Shelley D.; Goldstein, Cathy A.; Chervin, Ronald D.

    2016-01-01

    Pruritus (itching) during the sleep period can present as a symptom of dermatological or systemic disease, or as a parasomnia. Sleep related scratching as a primary parasomnia, exclusively confined to sleep in the absence of coexisting dermatological disorders, has not been well described. This case series describes three such patients, and discusses potentially relevant pathophysiology that can underlie itching or pain. Such cases of sleep related scratching may merit nosologic classification apart from previously defined parasomnias. Citation: Nigam G, Riaz M, Hershner SD, Goldstein CA, Chervin RD. Sleep related scratching: a distinct parasomnia? J Clin Sleep Med 2016;12(1):139–142. PMID:26285112

  6. Cat-scratch disease simulating lyphoma

    SciTech Connect

    Wong, T.Z.; Kruskal, J.; Kane, R.A.; Trey, G.

    1996-01-01

    Cat-scratch disease is the most common cause of benign lymphadenopathy in children and young adults. Rare cases of systemic involvement with deep adenopathy with or without hepatic and/or splenic involvement have been reported. We present an unusual case of cat-scratch disease with imaging findings indistinguishable from lymphoma. Cat-scratch disease should be considered as a possible benign etiology for adenopathy with hepatic or splenic nodules in a young patient, especially if the involved nodes are tender. 5 refs., 1 fig.

  7. Abrasive tip treatment for use on compressor blades

    NASA Technical Reports Server (NTRS)

    Pedersen, H. C.

    1984-01-01

    A co-spray process was used which simultaneously but separately introduces abrasive grits and metal matrix powder into the plasma stream and entraps the abrasive grits within a molten matrix to form an abrasive coating as the matrix material solidifies on test specimen surfaces. Spray trials were conducted to optimize spray parameter settings for the various matrix/grit combinations before actual spraying of the test specimens. Rub, erosion, and bond adhesion tests were conducted on the coated specimens in the as-sprayed condition as well as on coated specimens that were aged for 100 hours at a temperature of 866K (1100 F). Microscopic examinations were performed to determine the coating abrasive-particle content, the size and shape of the adhesive particles in the coating, and the extent of compositional or morphological changes resulting from the aging process. A nickel chromium/aluminum composite with No. 150 size (0.002 to 0.005 inch) silicon carbide grits was selected as the best matrix/abrasive combination of the candidates surveyed for coating compressor blade tips.

  8. Comparing the Air Abrasion Cutting Efficacy of Dentine Using a Fluoride-Containing Bioactive Glass versus an Alumina Abrasive: An In Vitro Study.

    PubMed

    Tan, Melissa H X; Hill, Robert G; Anderson, Paul

    2015-01-01

    Air abrasion as a caries removal technique is less aggressive than conventional techniques and is compatible for use with adhesive restorative materials. Alumina, while being currently the most common abrasive used for cutting, has controversial health and safety issues and no remineralisation properties. The alternative, a bioactive glass, 45S5, has the advantage of promoting hard tissue remineralisation. However, 45S5 is slow as a cutting abrasive and lacks fluoride in its formulation. The aim of this study was to compare the cutting efficacy of dentine using a customised fluoride-containing bioactive glass Na0SR (38-80 μm) versus the conventional alumina abrasive (29 μm) in an air abrasion set-up. Fluoride was incorporated into Na0SR to enhance its remineralisation properties while strontium was included to increase its radiopacity. Powder outflow rate was recorded prior to the cutting tests. Principal air abrasion cutting tests were carried out on pristine ivory dentine. The abrasion depths were quantified and compared using X-ray microtomography. Na0SR was found to create deeper cavities than alumina (p < 0.05) despite its lower powder outflow rate and predictably reduced hardness. The sharper edges of the Na0SR glass particles might improve the cutting efficiency. In conclusion, Na0SR was more efficacious than alumina for air abrasion cutting of dentine. PMID:26697067

  9. Comparing the Air Abrasion Cutting Efficacy of Dentine Using a Fluoride-Containing Bioactive Glass versus an Alumina Abrasive: An In Vitro Study

    PubMed Central

    Tan, Melissa H. X.; Hill, Robert G.; Anderson, Paul

    2015-01-01

    Air abrasion as a caries removal technique is less aggressive than conventional techniques and is compatible for use with adhesive restorative materials. Alumina, while being currently the most common abrasive used for cutting, has controversial health and safety issues and no remineralisation properties. The alternative, a bioactive glass, 45S5, has the advantage of promoting hard tissue remineralisation. However, 45S5 is slow as a cutting abrasive and lacks fluoride in its formulation. The aim of this study was to compare the cutting efficacy of dentine using a customised fluoride-containing bioactive glass Na0SR (38–80 μm) versus the conventional alumina abrasive (29 μm) in an air abrasion set-up. Fluoride was incorporated into Na0SR to enhance its remineralisation properties while strontium was included to increase its radiopacity. Powder outflow rate was recorded prior to the cutting tests. Principal air abrasion cutting tests were carried out on pristine ivory dentine. The abrasion depths were quantified and compared using X-ray microtomography. Na0SR was found to create deeper cavities than alumina (p < 0.05) despite its lower powder outflow rate and predictably reduced hardness. The sharper edges of the Na0SR glass particles might improve the cutting efficiency. In conclusion, Na0SR was more efficacious than alumina for air abrasion cutting of dentine. PMID:26697067

  10. A Profilometric Study to Assess the Role of Toothbrush and Toothpaste in Abrasion Process

    PubMed Central

    Kumar, Sandeep; Kumar Singh, Siddharth; Gupta, Anjali; Roy, Sayak; Sareen, Mohit; Khajuria, Sarang

    2015-01-01

    Statement of the Problem Despite of many studies conducted on toothbrushes and toothpaste to find out the culprit for abrasion, there is no clear cut evidence to pin point the real cause for abrasion. Purpose An in vitro assessment of the role of different types of toothbrushes (soft/ medium/hard) in abrasion process when used in conjunction with and without a dentifrice. Materials and Method Forty five freshly extracted, sound, human incisor teeth were collected for this study. Enamel specimens of approximately 9 mm2 were prepared by gross trimming of extracted teeth using a lathe machine (Baldor 340 Dental lathe; Ohio, USA). They were mounted on separate acrylic bases. The specimens were divided into three groups, each group containing 15 mounted specimens. Group 1 specimens were brushed with soft toothbrush; Group 2 brushed with medium toothbrush and Group 3 with hard toothbrush. Initially, all the mounted specimens in each group were brushed using dentifrice and then the same procedure was repeated with water as control. Profilometric readings were recorded pre and post to tooth brushing and the differences in readings served as proxy measure to assess surface abrasion. These values were then compared to each other. Kruskal Wallis and Mann-Whitney U test were performed. Results The results showed that brushing, with water alone, caused less abrasion than when toothpaste was added (p< 0.008). When brushed with water, the harder toothbrush caused more abrasion (higher Ra-value), but when toothpaste was added, the softer toothbrush caused more abrasion (p< 0.001). Conclusion Besides supporting the fact that toothpaste is needed to create a significant abrasion, this study also showed that a softer toothbrush can cause more abrasion than harder ones. The flexibility of bristles is only secondary to abrasion process and abrasivity of dentifrice has an important role in abrasion process. PMID:26535407

  11. Scratch modeling of polymeric materials with molecular dynamics

    NASA Astrophysics Data System (ADS)

    Hilbig, Travis

    It is impossible to determine the amount of money that is spent every replacing products damaged from wear, but it is safe to assume that it is in the millions of dollars. With metallic materials, liquid lubricants are often used to prevent wear from materials rubbing against one another. However, with polymeric materials, liquid lubricants cause swelling, creating an increase in friction and therefore increasing the wear. Therefore, a different method or methods to mitigate wear in polymers should be developed. For better understanding of the phenomenon of wear, scratch resistance testing can be used. For this project, classic molecular dynamics is used to study the mechanics of nanometer scale scratching on amorphous polymeric materials. As a first approach, a model was created for polyethylene, considering intramolecular and intermolecular interactions as well as mass and volume of the CH 2 monomers in a polymer chain. The obtained results include analysis of penetration depth and recovery percentage related to indenter force and size.

  12. Mars Exploration Rovers' Rock Abrasion Tool

    NASA Astrophysics Data System (ADS)

    Gorevan, S.; Myrick, T.; Davis, K.; Ji, J.; Bartlett, P.; Mukherjee, S.; Arafat, T.

    2003-04-01

    Each of the twin 2003 Mars Exploration Rovers will be equipped with a Rock Abrasion Tool (RAT) designed and tested by Honeybee Robotics. The RAT is a robotic grinding tool and science instrument about the size of a soda can and weighing less than 690 grams that is carried by the robotic arm or Instrument Deployment Device (IDD) of the rover. The primary purpose of the RAT is to remove the dust and surface rind from Mars rock targets to reveal the underlying petrographic features. After the RAT is placed and preloaded against the target rock by the IDD, all operations of the RAT are performed autonomously. Using three small motors to drive the rotation, revolve and z-axis subassemblies the RAT removes a 45 mm diameter, 5 mm deep patch of rock. The RAT has a resin-bonded diamond abrasion wheel and two brushes to provide a clean observation surface for the three surface instruments - APXS, Microscopic Imager and Moessbauer Spectrometer. Detailed design and operation descriptions, as well as recent qualification and operational testing results will be presented.

  13. Abrasive swivel assembly and method

    DOEpatents

    Hashish, Mohamed; Marvin, Mark

    1990-01-01

    An abrasive swivel assembly for providing a rotating, particle-laden fluid stream and, ultimately, a rotating particle-laden fluid jet is disclosed herein. This assembly includes a tubular arrangement for providing a particle-free stream of fluid, a swivel assembly for rotating a section of the tubular arrangement, and a tubular end section for introducing solid particles into the particle-free fluid stream at a point along the rotating tubular section, whereby to produce a particle-laden fluid stream. This last-mentioned stream can then be used in combination with a cooperating nozzle arrangement for providing a rotating particle-laden fluid jet. In an actual working embodiment, the fluid stream is of sufficiently high pressure so that the abrasive jet can be used as a cutting jet.

  14. Abrasive swivel assembly and method

    DOEpatents

    Hashish, Mohamed; Marvin, Mark

    1989-01-01

    An abrasive swivel assembly for providing a rotating, particle-laden fluid stream and, ultimately, a rotating particle-laden fluid jet is disclosed herein. This assembly includes a tubular arrangement for providing a particle-free stream of fluid, means for rotating a section of the tubular arrangement, and means for introducing solid particles into the particle-free fluid stream at a point along the rotating tubular section, whereby to produce a particle-laden fluid stream. This last-mentioned stream can then be used in combination with a cooperating nozzle arrangement for providing a rotating particle-laden fluid jet. In an actual working embodiment, the fluid stream is of sufficiently high pressure so that the abrasive jet can be used as a cutting jet.

  15. Abrasion resistance of titanium nitride coatings formed on titanium by ion-beam-assisted deposition.

    PubMed

    Sawase, T; Yoshida, K; Taira, Y; Kamada, K; Atsuta, M; Baba, K

    2005-02-01

    To improve the physical properties of the pure titanium surface, thin titanium nitride (TiN) films were deposited by means of ion-beam-assisted deposition. Film structure was confirmed as TiN by X-ray diffraction analysis. Surface hardness and abrasion resistance were significantly improved on TiN-coated specimens. Five combinations of oral hygiene instruments and materials were applied to the specimens as simulations of the oral environment. Treatment with the metal scaler and ultrasonic scaler severely changed the surface features and significantly increased the surface roughness parameters on pure titanium controls, whereas only small scratches and dull undulations were seen on the TiN-coated specimens. Profilometric tracings and scanning electron micrographs demonstrated the improved abrasion resistance of the TiN-coated specimens. PMID:15641983

  16. Electron Microscopy Abrasion Analysis of Candidate Fabrics for Planetary Space Suit Protective Overgarment Application

    NASA Technical Reports Server (NTRS)

    Hennessy, Mary J.

    1992-01-01

    The Electron Microscopy Abrasion Analysis of Candidate Fabrics for Planetary Space Suit Protective Overgarment Application is in support of the Abrasion Resistance Materials Screening Test. The fundamental assumption made for the SEM abrasion analysis was that woven fabrics to be used as the outermost layer of the protective overgarment in the design of the future, planetary space suits perform best when new. It is the goal of this study to determine which of the candidate fabrics was abraded the least in the tumble test. The sample that was abraded the least will be identified at the end of the report as the primary candidate fabric for further investigation. In addition, this analysis will determine if the abrasion seen by the laboratory tumbled samples is representative of actual EVA Apollo abrasion.

  17. Development of a thermal reclamation system for spent blasting abrasive

    SciTech Connect

    Bryan, B.B.; Mensinger, M.C.; Rehmat, A.G.

    1991-01-01

    Abrasive blasting is the most economical method for paint removal from large surface areas such as the hulls and tanks of oceangoing vessels. Tens of thousands of tons of spent abrasive are generated annually by blasting operations in private and US Navy shipyards. Some of this material is classified as hazardous waste, and nearly all of it is currently being either stockpiled or disposed in landfills. The rapid decline in available landfill space and corresponding rise in landfill tipping fees pose a severe problem for shipyard operators throughout the US. This paper discusses the results of a research and development program initiated by the Institute of Gas Technology and supported by the US Navy to develop and test a fluidized-bed thermal reclamation system for spent abrasive waste minimization. Bench- and pilot-scale reclaimer tests and reclaimed abrasive performance tests are described along with the current status of a program to build and test a 5-ton/hour prototype reclaimer at a US Navy shipyard.

  18. Improvement of adhesion strength and scratch resistance of fluorocarbon thin films by cryogenic treatment

    NASA Astrophysics Data System (ADS)

    Jiang, Xiaojun; Wang, Jun; Shen, Jinpeng; Li, Rui; Yang, Guangcheng; Huang, Hui

    2014-01-01

    Fluorocarbon thin films have been widely applied as protective coatings due to unique physical and chemical properties, but the scratch resistance and adhesion strength between the films and substrates are rather poor. Coating technologies for stronger scratch resistance and adhesion strength are definitely needed and have great significance in coatings applications of fluorocarbon thin films. In this work, the scratch resistance and adhesion strength between silicon substrates and fluorocarbon thin films deposited by radio frequency (R.F.) magnetron sputtering were improved via a remarkably simple, flexible and nondestructive cryogenic treatment method. The effect of the cryogenic treatment on the microstructure, hardness, adhesion strength and scratch resistance of fluorocarbon thin films were investigated. XPS results indicated that the content of fluorine decreased slightly and the amount of cross-linked units increased after cryogenic treatment. Furthermore, the hardness of fluorocarbon thin films slightly improved. Nano-scratch test revealed that fluorocarbon thin films after this treatment had excellent scratch resistance and good adhesion strength.

  19. Impact of substrate surface scratches on the laser damage resistance of multilayer coatings

    SciTech Connect

    Qiu, S; Wolfe, J; Monterrosa, A; Teslich, N; Feit, M; Pistor, T; Stolz, C

    2010-11-03

    Substrate scratches can limit the laser resistance of multilayer mirror coatings on high-peak-power laser systems. To date, the mechanism by which substrate surface defects affect the performance of coating layers under high power laser irradiation is not well defined. In this study, we combine experimental approaches with theoretical simulations to delineate the correlation between laser damage resistance of coating layers and the physical properties of the substrate surface defects including scratches. A focused ion beam technique is used to reveal the morphological evolution of coating layers on surface scratches. Preliminary results show that coating layers initially follow the trench morphology on the substrate surface, and as the thickness increases, gradually overcoat voids and planarize the surface. Simulations of the electrical-field distribution of the defective layers using the finite-difference time-domain (FDTD) method show that field intensification exists mostly near the top surface region of the coating near convex focusing structures. The light intensification could be responsible for the reduced damage threshold. Damage testing under 1064 nm, 3 ns laser irradiation over coating layers on substrates with designed scratches show that damage probability and threshold of the multilayer depend on substrate scratch density and width. Our preliminary results show that damage occurs on the region of the coating where substrate scratches reside and etching of the substrate before coating does not seem to improve the laser damage resistance.

  20. CSD skin test

    MedlinePlus

    The cat scratch disease (CSD) skin test was once used to help diagnose CSD. The test is no longer used today. ... LN, Welch DF, Koehler JE. Bartonella, including cat-scratch disease. In: Bennett JE, Dolin R, Blaser MJ, ...

  1. Aeolian Abrasion, a Dominant Erosion Agent in the Martian Environment

    NASA Astrophysics Data System (ADS)

    Bridges, N.; Cooper, G.; Eddlemon, E.; Greeley, R.; Laity, J.; Phoreman, J.; Razdan, A.; van Note, S.; White, B.; Wilson, G.

    2004-12-01

    Aeolian abrasion is one of the predominant erosion mechanisms on Mars today. Martian ventifacts record the climate under which the rocks were modified (wind direction, wind speeds and particle flux) and therefore tie into the overall climatic regime of the planet. By better understanding the rates at which rocks abrade and the features diagnostic of specific climatic conditions, we can gain insight into past climates. Herein we report on numerical models, wind tunnel experiments, and field work to determine 1) Particle and kinetic fluxes on Earth and Mars, 2) the degree to which these parameters control abrasion, and 3) how, in detail, rocks of various shapes and compositions erode over time. Kinetic energy generally increases with height, whereas flux decreases, and impact angles, which affect energy transfer, and rebound effects are functions of the rock facet angle. This results in a non-linear relationship between abrasion potential and height that is a function of wind speed, planetary environment, and target geometry. We have computed the first three of these parameters numerically using a numerical saltation code, combined with published flux calculations These results have been compared to wind tunnel tests of flux vs. height, abrasion of erodible targets, and high speed video analysis under terrestrial and Martian pressures. We are also using high resolution laser scanning to characterize textures, shapes, and weathering changes for terrestrial and Martian rocks at the 100s of microns scale. We find that facet angle, texture, and rock heterogeneity are of critical importance in determining the rate and style of abrasion. Field and theoretical results demonstrate that high speed winds, not the integrated flux of lower speeds, and sand, not dust, produce most rock abrasion. On Mars, this requires sustained winds above 20-25 m/s at the near surface, a challenge in the current environment.

  2. Abrasion-resistant coatings for plastic surfaces

    NASA Technical Reports Server (NTRS)

    Wydeven, T.; Hollahan, J. R.

    1976-01-01

    Optically clear composition of organosilicon compounds insulates plastic surfaces and protects them from abrasion. Plasma polymerization process produces superior uniformity and clarity than previous coating techniques.

  3. Abrasive drill for resilient materials

    NASA Technical Reports Server (NTRS)

    Koch, A. J.

    1981-01-01

    Resilient materials normally present problem in obtaining accurate and uniform hole size and position. Tool is fabricated from stiff metal rod such as tungsten or carbon steel that has diameter slightly smaller than required hole. Piercing/centering point is ground on one end of rod. Rod is then plasma-sprayed (flame-sprayed) with suitable hard abrasive coating. High-speed, slow-feed operation of tool is necessary for accurate holes, and this can be done with drill press, hard drill, or similar machines.

  4. Innovative decontamination technology by abrasion in vibratory vessels

    SciTech Connect

    Fabbri, Silvio; Ilarri, Sergio

    2007-07-01

    Available in abstract form only. Full text of publication follows: The possibility of using conventional vibratory vessel technology as a decontamination technique is the motivation for the development of this project. The objective is to explore the feasibility of applying the vibratory vessel technology for decontamination of radioactively-contaminated materials such as pipes and metal structures. The research and development of this technology was granted by the U.S. Department of Energy (DOE). Abrasion processes in vibratory vessels are widely used in the manufacture of metals, ceramics, and plastics. Samples to be treated, solid abrasive media and liquid media are set up into a vessel. Erosion results from the repeated impact of the abrasive particles on the surface of the body being treated. A liquid media, generally detergents or surfactants aid the abrasive action. The amount of material removed increases with the time of treatment. The design and construction of the machine were provided by Vibro, Argentina private company. Tests with radioactively-contaminated aluminum tubes and a stainless steel bar, were performed at laboratory level. Tests showed that it is possible to clean both the external and the internal surface of contaminated tubes. Results show a decontamination factor around 10 after the first 30 minutes of the cleaning time. (authors)

  5. New ichnospecies of scratching traces from phosphatic nodules (Cenomanian, England)

    NASA Astrophysics Data System (ADS)

    Chumakov, N. M.; Dronov, A. V.; Mikuláš, R.

    2013-05-01

    Surfaces of phosphorite nodules and pebbles from the "Cambridge Green Sand" (Cenomanian, South England) yielded several discernible types of scratches. These originated before the burial of nodules/pebbles as evidenced by fossil epibiotic oysters cemented to cover the scratches. The individual forms of scratches differ in size and shape; therefore, the set of "scratching instruments" also had to be different. The scratches described differ from scratches generated by glacial processes, namely by the regularity of length and intervals, parallel orientation, existence of recurrent forms and placement along the nodule edges. We interpret the scratches as trace fossils of the ichnogenus Machichnus. Three new species, namely M. normani, M. harlandi and M. jeansi, are erected for them herein. The series of scratches originated probably by teeth on a couple of jaws; the makers possibly scraped bacterial or algal film off the surface of nodules that were covered with the phosphate gel. Both homodont and heterodont animals (probably fish) were involved.

  6. Alice, Greenfoot, and Scratch--A Discussion

    ERIC Educational Resources Information Center

    Utting, Ian; Cooper, Stephen; Kolling, Michael; Maloney, John; Resnick, Mitchel

    2010-01-01

    This article distills a discussion about the goals, mechanisms, and effects of three environments which aim to support the acquisition and development of computing concepts (problem solving and programming) in pre-University and non-technical students: Alice, Greenfoot, and Scratch. The conversation started in a special session on the topic at the…

  7. The From Scratch Rhythm Workbook. Revised Edition.

    ERIC Educational Resources Information Center

    Dadson, Philip; McGlashan, Don

    Since its formation in 1974, the renowned performing group, "From Scratch," has developed a distinctive style of music using sophisticated rhythmic language and unique sculptural instruments. The group's experiences have been transformed into the exercises and game forms presented in this workbook. The hands-on workbook uses a body-based approach…

  8. Exposure to crystalline silica in abrasive blasting operations where silica and non-silica abrasives are used.

    PubMed

    Radnoff, Diane L; Kutz, Michelle K

    2014-01-01

    Exposure to respirable crystalline silica is a hazard common to many industries in Alberta but particularly so in abrasive blasting. Alberta occupational health and safety legislation requires the consideration of silica substitutes when conducting abrasive blasting, where reasonably practicable. In this study, exposure to crystalline silica during abrasive blasting was evaluated when both silica and non-silica products were used. The crystalline silica content of non-silica abrasives was also measured. The facilities evaluated were preparing metal products for the application of coatings, so the substrate should not have had a significant contribution to worker exposure to crystalline silica. The occupational sampling results indicate that two-thirds of the workers assessed were potentially over-exposed to respirable crystalline silica. About one-third of the measurements over the exposure limit were at the work sites using silica substitutes at the time of the assessment. The use of the silica substitute, by itself, did not appear to have a large effect on the mean airborne exposure levels. There are a number of factors that may contribute to over-exposures, including the isolation of the blasting area, housekeeping, and inappropriate use of respiratory protective equipment. However, the non-silica abrasives themselves also contain silica. Bulk analysis results for non-silica abrasives commercially available in Alberta indicate that many contain crystalline silica above the legislated disclosure limit of 0.1% weight of silica per weight of product (w/w) and this information may not be accurately disclosed on the material safety data sheet for the product. The employer may still have to evaluate the potential for exposure to crystalline silica at their work site, even when silica substitutes are used. Limited tests on recycled non-silica abrasive indicated that the silica content had increased. Further study is required to evaluate the impact of product recycling

  9. Programming by Choice: Urban Youth Learning Programming with Scratch

    ERIC Educational Resources Information Center

    Maloney, John; Peppler, Kylie; Kafai, Yasmin B.; Resnick, Mitchel; Rusk, Natalie

    2008-01-01

    This paper describes Scratch, a visual, block-based programming language designed to facilitate media manipulation for novice programmers. We report on the Scratch programming experiences of urban youth ages 8-18 at a Computer Clubhouse--an after school center--over an 18-month period. Our analyses of 536 Scratch projects collected during this…

  10. SPECIFIC ENERGY AND SCRATCH HARDNESS OF GAMMA TITANIUM ALUMINIDES SUBJECTED TO SINGLE-GRIT PENDULUM SCRATCHING

    SciTech Connect

    Wang, Hong; Lin, Hua-Tay; Wereszczak, Andrew A

    2006-01-01

    Two gamma titanium aluminides TiAls (Daido TiAl HIP and HOWMET TiAl) with fully lamellar structure but with different colony sizes were studied using a single-grit pendulum (rotational) scratch tester. The maximum depth of groove was ~ 0.07 mm and the scratch velocity used was ~ 1,000 mm/s. Normal and tangential forces were monitored during each scratch. The material removal mechanisms were examined using a scanning electronic microscope (SEM), and also measured by using a laser profilometer. Extensive thermal softening was observed. Sizable fractures were revealed in the transverse direction; however the role of these fractures in the chip formation depends on the microstructure of materials and the size of groove. The tribological properties were characterized by instantaneous specific energy and scratch hardness as related to the depth of groove. The overall response of materials can be effectively characterized by a two-parameter model, namely, HEM model and PSR model, even though the underlining material removal might be subjected to the different mechanisms. The TiAl with the larger colony or grain size exhibits a strong resistance to material loss or material removal (higher depth-independent specific energy) while exhibiting lower scratch hardness. The obtained depth-independent specific energy and scratch hardness can be used to screen the candidate materials depending on whether the application is sliding or impact dominant.

  11. A nonmineralized approach to abrasion-resistant biomaterials

    PubMed Central

    Pontin, Michael G.; Moses, Dana N.; Waite, J. Herbert; Zok, Frank W.

    2007-01-01

    The tooth-like mouthparts of some animals consist of biomacromolecular scaffolds with few mineral components, making them intriguing paradigms of biostructural materials. In this study, the abrasion resistance of the jaws of one such animal, the bloodworm Glycera dibranchiata, has been evaluated by nanoindentation, nanoscratching, and wear testing. The hardest, stiffest, and most abrasion-resistant materials are found within a thin (<3 μm) surface layer near the jaw tip and a thicker (10–20 μm) subsurface layer, both rich in unmineralized Cu. These results are consistent with the supposition that Cu ions are involved in the formation of intermolecular coordination complexes between proteins, creating a highly cross-linked molecular network. The intervening layer contains aligned atacamite [Cu2(OH)3Cl] fibers and exhibits hardness and stiffness (transverse to the alignment direction) that are only slightly higher than those of the bulk material but lower than those of the two Cu-rich layers. Furthermore, the atacamite-containing layer is the least abrasion-resistant, by a factor of ≈3, even relative to the bulk material. These observations are broadly consistent with the behavior of engineering polymer composites with hard fiber or particulate reinforcements. The alignment of fibers parallel to the jaw surface, and the fiber proximity to the surface, are both suggestive of a natural adaptation to enhance bending stiffness and strength rather than to endow the surface regions with enhanced abrasion resistance. PMID:17702868

  12. Ceramic-bonded abrasive grinding tools

    DOEpatents

    Holcombe, Jr., Cressie E.; Gorin, Andrew H.; Seals, Roland D.

    1994-01-01

    Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

  13. Ceramic-bonded abrasive grinding tools

    DOEpatents

    Holcombe, C.E. Jr.; Gorin, A.H.; Seals, R.D.

    1994-11-22

    Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

  14. Ultrasonic Abrasive Removal Of EDM Recast

    NASA Technical Reports Server (NTRS)

    Mandel, Johnny L.; Jacobson, Marlowe S.

    1990-01-01

    Ultrasonic abrasive process removes layer of recast material generated during electrical-discharge machining (EDM) of damper pocket on turbine blade. Form-fitted tool vibrated ultrasonically in damper pocket from which material removed. Vibrations activate abrasive in pocket. Amount of material removed controlled precisely.

  15. Corneal abrasions associated with pepper spray exposure.

    PubMed

    Brown, L; Takeuchi, D; Challoner, K

    2000-05-01

    Pepper spray containing oleoresin capsicum is used by law enforcement and the public as a form of nonlethal deterrent. Stimulated by the identification of a case of a corneal abrasion associated with pepper spray exposure, a descriptive retrospective review of a physician-maintained log of patients presenting to a jail ward emergency area over a 3-year period was performed. The objective was to give some quantification to the frequency with which an emergency physician could expect to see corneal abrasions associated with pepper spray exposure. Of 100 cases of pepper spray exposure identified, seven patients had sustained corneal abrasions. We conclude that corneal abrasions are not rare events when patients are exposed to pepper spray and that fluorescein staining and slit lamp or Wood's lamp examination should be performed on all exposed patients in whom corneal abrasions cannot be excluded on clinical grounds. PMID:10830682

  16. Linear abrasion of a titanium superhydrophobic surface prepared by ultrafast laser microtexturing

    NASA Astrophysics Data System (ADS)

    Steele, Adam; Nayak, Barada K.; Davis, Alexander; Gupta, Mool C.; Loth, Eric

    2013-11-01

    A novel method of fabricating titanium superhydrophobic surfaces by ultrafast laser irradiation is reported. The ultrafast laser irradiation creates self-organized microstructure superimposed with nano-scale roughness, after which a fluoropolymer coating is applied to lower the surface energy of the textured surface and achieve superhydrophobicity. The focus of this study is to investigate abrasion effects on this mechanically durable superhydrophobic surface. The mechanical durability is analyzed with linear abrasion testing and microscopy imaging. Linear abrasion tests indicate that these surfaces can resist complete microstructure failure up to 200 abrasion cycles and avoid droplet pinning up to ten abrasion cycles at 108.4 kPa applied pressure, which roughly corresponds to moderate to heavy sanding or rubbing in the presence of abrasive particles. The wear mechanisms are also investigated and the primary mechanism for this system is shown to be abrasive wear with fatigue by repeated plowing. Although these results demonstrate an advancement in mechanical durability over the majority of existing superhydrophobic surfaces, it exemplifies the challenge in creating superhydrophobic surfaces with suitable mechanical durability for harsh applications, even when using titanium.

  17. Characterization and dispersion of pollutant releases from the abrasive blasting of lead paint from steel bridges

    SciTech Connect

    Lee, M.; Rana, B.

    1999-07-01

    The characterization of airborne and spent material for abrasive blasting of steel paint was performed as part of the Environmental Impact Statement for Lead Paint Removal Operations on New York City Department of Transportation Bridges1. Laboratory tests were performed on painted steel components of the Williamsburg Bridge, to determine the sizes of particles typically released into the air as aerosol and onto the ground as bulk material, as a result of accidental releases from abrasive blasting operations. Two of the most commonly used abrasives for paint removal on steel structures, recyclable steel grit and expendable abrasives were subjected to the laboratory tests. The results of the tests were used to determine the percentage of existing paint and abrasive which becomes airborne and the resultant particle size distributions, which were employed in the air quality concentration and deposition modeling for the EIS. Particle size distributions of the airborne material indicated that the profiles of airborne lead and particulate matter have a mean particle size between 15 and 21 microns. Spent abrasives and paint chips that settle on the floor are larger in size with a mean diameter greater than 259 microns, although up to 6% of this material has a mean diameter less than 50 microns. The percentage of paint and expendable abrasives that become airborne as a result of abrasive blasting were estimated to be as high as 9.0 and 12.4%, respectively. Potential release rates were derived for total accumulation (duration of the project), annual, quarterly, 24-hour, and 1-hour time averaging periods for abrasives, lead, and other metals. Pollutant releases were simulated as individual sources at multiple release heights with the Environment Protection Agency's ISC3ST model for six representative bridges near potential places of public exposure.

  18. Combined effect of end-rounded versus tapered bristles and a dentifrice on plaque removal and gingival abrasion.

    PubMed

    Caporossi, Leonardo Stephan; Dutra, Danilo Antonio Milbradt; Martins, Maritieli Righi; Prochnow, Emilia Pithan; Moreira, Carlos Heitor Cunha; Kantorski, Karla Zanini

    2016-01-01

    Two previous clinical studies evaluated the effect of end-rounded versus tapered bristles of soft manual brushes on the removal of plaque and gingival abrasion. However, the combined effect of an abrasive dentifrice on these outcomes has yet to be understood. The purpose of the present study was to compare the incidence of gingival abrasion and the degree of plaque removal obtained after the use of toothbrushes with tapered or end-rounded bristles in the presence or absence of an abrasive dentifrice. The study involved a randomized, single-blind, crossover model (n = 39) with a split-mouth design. Subjects were instructed to refrain from performing oral hygiene procedures for 72 hours. Quadrants were randomized and subjects brushed with both types of toothbrushes using a dentifrice (relative dentin abrasion = ± 160). Plaque and gingival abrasion were assessed before and after brushing. After 7 days, the experiment was repeated without the dentifrice. The average reduction in plaque scores and the average increase in the number of abrasion sites were assessed by repeated-measures ANOVA and Bonferroni's post-hoc tests. End-rounded bristles removed significantly more plaque than tapered bristles, regardless of the use of a dentifrice. The dentifrice did not improve plaque removal. In the marginal area (cervical free gingiva), no difference in the incidence of gingival abrasion was detected between toothbrush types when used with a dentifrice (p ≥ 0.05). However, the dentifrice increased the incidence of abrasion (p < 0.001), irrespective of the toothbrush type tested. End-rounded bristles therefore removed plaque more effectively without causing a higher incidence of gingival abrasion when compared with tapered bristles. An abrasive dentifrice can increase the incidence of abrasion, and should be used with caution by individuals who are at risk of developing gingival recession. PMID:26981758

  19. Surface roughness and gloss of current CAD/CAM resin composites before and after toothbrush abrasion.

    PubMed

    Koizumi, Hiroyasu; Saiki, Osamu; Nogawa, Hiroshi; Hiraba, Haruto; Okazaki, Tomoyo; Matsumura, Hideo

    2015-01-01

    The purpose of this study was to evaluate the gloss and surface roughness behaviors of newly developed CAD/CAM composite blocks with different filler contents and characteristics. The gloss and surface roughness were quantified before and after a toothbrush dentifrice abrasion test; the results were compared to the gloss and surface roughness of a ceramic CAD/CAM block. Knoop hardness was determined before abrasion test. The results were analyzed by ANOVA, Tukey HSD, and Dunnett t test (p<0.05). The rank order of Knoop hardness was as follows: Vita Mark II>Vita Enamic>Gradia block>Shofu Block HC, Lava Ultimate≥Katana Avencia block≥Cerasmart. After toothbrush abrasion, a significant difference in the gloss unit was detected between the Shofu Block HC material and the ceramic block. The Ra and Rz of the Cerasmart and Shofu Block HC materials were significantly larger than those of the ceramic block after toothbrush abrasion. PMID:26632238

  20. Abrasive wear by coal-fueled diesel engine and related particles

    SciTech Connect

    Ives, L.K.

    1992-09-01

    The development of commercially viable diesel engines that operate directly on pulverized coal-fuels will require solution to the problem of severe abrasive wear. The purpose of the work described in this report was to investigate the nature of the abrasive wear problem. Analytical studies were carried out to determine the characteristics of the coal-fuel and associated combustion particles responsible for abrasion. Laboratory pinon-disk wear tests were conducted on oil-particle mixtures to determine the relationship between wear rate and a number of different particle characteristics, contact parameters, specimen materials properties, and other relevant variables.

  1. Hepatosplenic Cat Scratch Disease in Immunocompetent Adults

    PubMed Central

    García, Juan C.; Núñez, Manuel J.; Castro, Begoña; Fernández, Jesús M.; Portillo, Aránzazu; Oteo, José A.

    2014-01-01

    Abstract Cat-scratch disease (CSD) is the most frequent presentation of Bartonella henselae infection. It has a worldwide distribution and is associated with a previous history of scratch or bite from a cat or dog. CSD affects children and teenagers more often (80%) than adults, and it usually has a self-limiting clinical course. Atypical clinical course or systemic symptoms are described in 5%–20% of patients. Among them, hepatosplenic (HS) forms (abscess) have been described. The majority of published cases have affected children or immunosuppressed patients. Few cases of HS forms of CSD in immunocompetent adult hosts have been reported, and data about the management of this condition are scarce. Herein, we present 3 new cases of HS forms of CSD in immunocompetent adults and review 33 other cases retrieved from the literature. We propose an approach to clinical diagnosis and treatment with oral azithromycin. PMID:25398062

  2. Toe scratches cause scabby hip syndrome lesions.

    PubMed

    Hargis, B M; Moore, R W; Sams, A R

    1989-08-01

    Scabs and scratches in the hip region of chicken carcasses have become the single most common cause of downgrading and required trimming at processing in some areas of the United States. Repeatable correlations with microbiological agents, environment, and nutrition have not been observed. The present report provides evidence that scabs and scratches, present at processing, are the result of injuries inflicted by toenails of birds as they climb on one another. Onychectomy (removal of approximately two-thirds of the distal phalanx) of all four digits of each foot prior to chick placement resulted in 3.7 and 4.8-fold reduction in subjective lesion scores and 7 to 10-fold increases in the percentage of USDA Grade A carcasses at a commercial processing plant. PMID:2780490

  3. Measurement of surface scratches on aircraft structures

    NASA Astrophysics Data System (ADS)

    Sarr, Dennis P.

    1996-01-01

    In assuring the quality of aircraft, the skin quality must be free of surface imperfections. Surface imperfections such as scratches are unacceptable for cosmetic and structural reasons. Scratches beyond a certain depth are not repairable, resulting in costly replacement of an aircraft's part. Measurements of aircraft exterior surfaces require a ladder or cherry picker for positioning the inspector. Commercially-available computer vision systems are not portable, easy to use, or ergonomic. The machine vision system must be designed with these criteria in mind. The scratch measurement system (SMS) uses computer vision, digital signal processing, and automated inspection methods. The system is portable and battery powered. It is certified for measuring the depth and width of the anomaly. The SMS provides a comprehensive, analytical, and accurate reading. A hardcopy output provides a permanent record of the analysis. The graphical data shows the surface profile and provides substantial information of the surface anomaly. The factory and flight line use the SMS at different stages of aircraft production. Six systems have been built for use within Boeing. A patent was issued for the SMS in February 1994.

  4. A nanometric cushion for enhancing scratch and wear resistance of hard films

    PubMed Central

    Gotlib-Vainshtein, Katya; Girshevitz, Olga; Barlam, David

    2014-01-01

    Summary Scratch resistance and friction are core properties which define the tribological characteristics of materials. Attempts to optimize these quantities at solid surfaces are the subject of intense technological interest. The capability to modulate these surface properties while preserving both the bulk properties of the materials and a well-defined, constant chemical composition of the surface is particularly attractive. We report herein the use of a soft, flexible underlayer to control the scratch resistance of oxide surfaces. Titania films of several nm thickness are coated onto substrates of silicon, kapton, polycarbonate, and polydimethylsiloxane (PDMS). The scratch resistance measured by scanning force microscopy is found to be substrate dependent, diminishing in the order PDMS, kapton/polycarbonate, Si/SiO2. Furthermore, when PDMS is applied as an intermediate layer between a harder substrate and titania, marked improvement in the scratch resistance is achieved. This is shown by quantitative wear tests for silicon or kapton, by coating these substrates with PDMS which is subsequently capped by a titania layer, resulting in enhanced scratch/wear resistance. The physical basis of this effect is explored by means of Finite Element Analysis, and we suggest a model for friction reduction based on the "cushioning effect” of a soft intermediate layer. PMID:25161836

  5. A nanometric cushion for enhancing scratch and wear resistance of hard films.

    PubMed

    Gotlib-Vainshtein, Katya; Girshevitz, Olga; Sukenik, Chaim N; Barlam, David; Cohen, Sidney R

    2014-01-01

    Scratch resistance and friction are core properties which define the tribological characteristics of materials. Attempts to optimize these quantities at solid surfaces are the subject of intense technological interest. The capability to modulate these surface properties while preserving both the bulk properties of the materials and a well-defined, constant chemical composition of the surface is particularly attractive. We report herein the use of a soft, flexible underlayer to control the scratch resistance of oxide surfaces. Titania films of several nm thickness are coated onto substrates of silicon, kapton, polycarbonate, and polydimethylsiloxane (PDMS). The scratch resistance measured by scanning force microscopy is found to be substrate dependent, diminishing in the order PDMS, kapton/polycarbonate, Si/SiO2. Furthermore, when PDMS is applied as an intermediate layer between a harder substrate and titania, marked improvement in the scratch resistance is achieved. This is shown by quantitative wear tests for silicon or kapton, by coating these substrates with PDMS which is subsequently capped by a titania layer, resulting in enhanced scratch/wear resistance. The physical basis of this effect is explored by means of Finite Element Analysis, and we suggest a model for friction reduction based on the "cushioning effect" of a soft intermediate layer. PMID:25161836

  6. Quantitative image analysis for evaluating the abrasion resistance of nanoporous silica films on glass

    NASA Astrophysics Data System (ADS)

    Nielsen, Karsten H.; Karlsson, Stefan; Limbach, Rene; Wondraczek, Lothar

    2015-12-01

    The abrasion resistance of coated glass surfaces is an important parameter for judging lifetime performance, but practical testing procedures remain overly simplistic and do often not allow for direct conclusions on real-world degradation. Here, we combine quantitative two-dimensional image analysis and mechanical abrasion into a facile tool for probing the abrasion resistance of anti-reflective (AR) coatings. We determine variations in the average coated area, during and after controlled abrasion. Through comparison with other experimental techniques, we show that this method provides a practical, rapid and versatile tool for the evaluation of the abrasion resistance of sol-gel-derived thin films on glass. The method yields informative data, which correlates with measurements of diffuse reflectance and is further supported by qualitative investigations through scanning electron microscopy. In particular, the method directly addresses degradation of coating performance, i.e., the gradual areal loss of antireflective functionality. As an exemplary subject, we studied the abrasion resistance of state-of-the-art nanoporous SiO2 thin films which were derived from 5-6 wt% aqueous solutions of potassium silicates, or from colloidal suspensions of SiO2 nanoparticles. It is shown how abrasion resistance is governed by coating density and film adhesion, defining the trade-off between optimal AR performance and acceptable mechanical performance.

  7. Quantitative image analysis for evaluating the abrasion resistance of nanoporous silica films on glass

    PubMed Central

    Nielsen, Karsten H.; Karlsson, Stefan; Limbach, Rene; Wondraczek, Lothar

    2015-01-01

    The abrasion resistance of coated glass surfaces is an important parameter for judging lifetime performance, but practical testing procedures remain overly simplistic and do often not allow for direct conclusions on real-world degradation. Here, we combine quantitative two-dimensional image analysis and mechanical abrasion into a facile tool for probing the abrasion resistance of anti-reflective (AR) coatings. We determine variations in the average coated area, during and after controlled abrasion. Through comparison with other experimental techniques, we show that this method provides a practical, rapid and versatile tool for the evaluation of the abrasion resistance of sol-gel-derived thin films on glass. The method yields informative data, which correlates with measurements of diffuse reflectance and is further supported by qualitative investigations through scanning electron microscopy. In particular, the method directly addresses degradation of coating performance, i.e., the gradual areal loss of antireflective functionality. As an exemplary subject, we studied the abrasion resistance of state-of-the-art nanoporous SiO2 thin films which were derived from 5–6 wt% aqueous solutions of potassium silicates, or from colloidal suspensions of SiO2 nanoparticles. It is shown how abrasion resistance is governed by coating density and film adhesion, defining the trade-off between optimal AR performance and acceptable mechanical performance. PMID:26656260

  8. Influence of Corrosion on the Abrasion of Cutter Steels Used in TBM Tunnelling

    NASA Astrophysics Data System (ADS)

    Espallargas, N.; Jakobsen, P. D.; Langmaack, L.; Macias, F. J.

    2015-01-01

    Abrasion on tunnel boring machine (TBM) cutters may be critical in terms of project duration and costs. Several researchers are currently studying the degradation of TBM cutter tools used for excavating hard rock, soft ground and loose soil. So far, the primary focus of this research has been directed towards abrasive wear. Abrasive wear is a very common process in TBM excavation, but with a view to the environment in which the tools are working, corrosion may also exert an influence. This paper presents a selection of techniques that can be used to evaluate the influence of corrosion on abrasion on TBM excavation tools. It also presents the influence of corrosion on abrasive wear for some initial tests, with constant steel and geomaterial and varying properties of the excavation fluids (soil conditioners, anti-abrasion additives and water). The results indicate that the chloride content in the water media greatly influences the amount of wear, providing evidence of the influence of corrosion on the abrasion of the cutting tools. The presence of conditioning additives tailored to specific rock or soil conditions reduces wear. However, when chloride is present in the water, the additives minimise wear rates but fail to suppress corrosion of the cutting tools.

  9. Micro-abrasion-corrosion behaviour of a biomedical Ti-25Nb-3Mo-3Zr-2Sn alloy in simulated physiological fluid.

    PubMed

    Wang, Zhenguo; Li, Yan; Huang, Weijiu; Chen, Xiaoli; He, Haoran

    2016-10-01

    The micro-abrasion-corrosion behaviour of the biomedical Ti-25Nb-3Mo-3Zr-2Sn alloy in Hank׳s solution with protein has been investigated using electrochemical measurements, tribological tests and scanning electron microscope (SEM) observations. The potentiodynamic polarization tests showed that the corrosion potential (Ecorr) exhibits the maximum value at the abrasive concentration of 0.05gcm(-3) despite of the load level. The tribological results indicated that the total material loss of the Ti-25Nb-3Mo-3Zr-2Sn alloy during micro-abrasion increased with the increasing abrasive concentration at a certain applied load. When the abrasive concentration is no more than 0.15gcm(-3), the total material loss increases with increasing load, while the total material loss exhibits the maximum value at a moderate load in case of higher abrasive concentration levels. This was ascribed to the three-body or two-body micro-abrasion-corrosion at different abrasive concentration levels. The wastage map, abrasion mode map and synergy map associated with the applied load and the abrasive concentration were constructed to evaluate the micro-abrasion-corrosion behaviour of the Ti-25Nb-3Mo-3Zr-2Sn alloy in potential biomedical applications. PMID:27450038

  10. Wheel Abrasion Experiment Metals Selection for Mars Pathfinder Mission

    NASA Technical Reports Server (NTRS)

    Hepp, Aloysius F.; Fatemi, Navid S.; Wilt, David M.; Ferguson, Dale C.; Hoffman, Richard; Hill, Maria M.; Kaloyeros, Alain E.

    1996-01-01

    A series of metals was examined for suitability for the Wheel Abrasion Experiment, one of ten microrover experiments of the Mars Pathfinder Mission. The seven candidate metals were: Ag, Al, Au, Cu, Ni, Pt, and W. Thin films of candidate metals from 0.1 to 1.0 micrometer thick were deposited on black anodized aluminum coupons by e-beam and resistive evaporation and chemical vapor deposition. Optical, corrosion, abrasion, and adhesion criteria were used to select Al, Ni, and Pt. A description is given of the deposition and testing of thin films, followed by a presentation of experimental data and a brief discussion of follow-on testing and flight qualification.

  11. Cat scratch disease and lymph node tuberculosis in a colon patient with cancer.

    PubMed

    Matias, M; Marques, T; Ferreira, M A; Ribeiro, L

    2013-01-01

    A 71-year-old man operated for a sigmoid tumour remained in the surveillance after adjuvant chemotherapy. After 3 years, a left axillary lymph node was visible on CT scan. The biopsy revealed a necrotising and abscessed granulomatous lymphadenitis, suggestive of cat scratch disease. The patient confirmed having been scratched by a cat and the serology for Bartonella henselae was IgM+/IgG-. Direct and culture examinations for tuberculosis were negative. The patient was treated for cat scratch disease. One year later, the CT scan showed increased left axillary lymph nodes and a left pleural effusion. Direct and cultural examinations to exclude tuberculosis were again negative. Interferon-γ release assay testing for tuberculosis was undetermined and then positive. Lymph node and pleural tuberculosis were diagnosed and treated with a good radiological response. This article has provides evidence of the importance of continued search for the right diagnosis and that two diagnoses can happen in the same patient. PMID:24334464

  12. Raising the resistance of mainline pump parts to hydraulic abrasion

    SciTech Connect

    Belousov, V.Ya.; Borisenko, V.V.; Zhuravlev, Yu.V.

    1988-01-01

    The authors investigate the diffusion coating of mainline petroleum pump surfaces with boron carbides and the subsequent hardness and abrasion resistance of the working surfaces based on the temperature of the treatment and the depth and concentration of the coating. Industrial testing on an NM 2500 x 230 centrifugal pump demonstrated an increase in service life by a factor of 2 to 2.5. The process has been put into production at an annual savings per pump of 4000 rubles.

  13. Shotcup petal abrasions in close range .410-caliber shotgun injuries.

    PubMed

    Dowling, G P; Dickinson, J A; Cooke, C T

    1988-01-01

    Shotcup petal abrasions centered around a shotgun wound of entrance are generally thought to occur at a range of 30 to 90 cm. A suicidal .410-caliber shotgun injury of the right eye is described in which typical petal abrasions were noted around the entrance wound. However, significant soot deposition around the wound suggested that the range of fire was less than 30 cm and perhaps closer to 15 cm. Test-firing of the weapon and ammunition used by the decedent showed some spread of the shotcup petals at a range of 7.5 cm, progressing to maximum spread at 30 to 52.5 cm. Further testing with other .410 ammunition, containing shotcups, confirmed the spread of shotcup petals at ranges less than 30 cm, irrespective of manufacturer, shotshell length, and birdshot size. When a variety of shotguns were tested, it was found that one weapon with a very short barrel and cylinder bore did not exhibit petal spread until a range of 30 cm was reached. The remaining shotguns, with longer barrels and full choke, all demonstrated definite petal spread at a range of 12.5 cm. The long, narrow configuration of .410 shotcup petals may explain their early spread and the production of petal abrasions at ranges of less than 30 cm. PMID:3351464

  14. Color Doppler pseudolymphomatous manifestations of the cat scratch disease.

    PubMed

    Smajlovic, Fahrudin; Ibralic, Muris

    2009-01-01

    Cat Scratch Disease (CSD) is an infectious illness, caused by the Bartonella henselae bacterium. Besides the common infective symptoms, swelling in the axillary and cervical region is very common and is usually evaluated by Color Doppler US (CDUS) (among other diagnostic methods). The aim of this work is to present ultrasound findings of the Cat Scratch Disease. During 2002 and 2003, we followed four patients (three male and one female) by CDUS, with different manifestations of the disease. The average age of the patients was 12. In all four cases, the local and generalized lymphadenopathy was found, and in two cases we found multiple focal hepatolienal lesions as well. The enlarged lymph nodes were found, with heterogeneous echogenicity of the cortex, and increased number of the hiluses, disturbed vascular structure and non specific hemodynamic. Hepatolienal lesions were hypoechogenic, round, unclear outline, and poorly vascularised. CDUS has proved to be a very sensitive imaging method in detection of pathomorphologic and hemodynamic changes of superficial lymph nodes and focal lesions of visceral organs in CSD. Opposite to the high sensitivity, its specificity is much lower, because of similar findings in lymphoma, TB lymphadenopathy and multiple visceral abscesses. Detailed anamnesis, clinical findings, with laboratory and specific serological tests (IgG, IgM), US characteristics, sometimes percutaneous aspiration biopsy as well, are crucial in determination of etiology of the disease. PMID:20380135

  15. Aircraft exterior scratch measurement system using machine vision

    NASA Astrophysics Data System (ADS)

    Sarr, Dennis P.

    1991-08-01

    In assuring the quality of aircraft skin, it must be free of surface imperfections and structural defects. Manual inspection methods involve mechanical and optical technologies. Machine vision instrumentation can be automated for increasing the inspection rate and repeatability of measurement. As shown by previous industry experience, machine vision instrumentation methods are not calibrated and certified as easily as mechanical devices. The defect must be accurately measured and documented via a printout for engineering evaluation and disposition. In the actual usage of the instrument for inspection, the device must be portable for factory usage, on the flight line, or on an aircraft anywhere in the world. The instrumentation must be inexpensive and operable by a mechanic/technician level of training. The instrument design requirements are extensive, requiring a multidisciplinary approach for the research and development. This paper presents the image analysis results of microscopic structures laser images of scratches on various surfaces. Also discussed are the hardware and algorithms used for the microscopic structures laser images. Dedicated hardware and embedded software for implementing the image acquisition and analysis have been developed. The human interface, human vision is used for determining which image should be processed. Once the image is chosen for analysis, the final answer is a numerical value of the scratch depth. The result is an answer that is reliable and repeatable. The prototype has been built and demonstrated to Boeing Commercial Airplanes Group factory Quality Assurance and flight test management with favorable response.

  16. 21 CFR 872.6010 - Abrasive device and accessories.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories. (a) Identification. An abrasive device and accessories is a device constructed of various abrasives... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Abrasive device and accessories. 872.6010...

  17. 21 CFR 872.6010 - Abrasive device and accessories.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories. (a) Identification. An abrasive device and accessories is a device constructed of various abrasives... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Abrasive device and accessories. 872.6010...

  18. 21 CFR 872.6010 - Abrasive device and accessories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories. (a) Identification. An abrasive device and accessories is a device constructed of various abrasives... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Abrasive device and accessories. 872.6010...

  19. 30 CFR 72.610 - Abrasive blasting.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed... mines. Silica sand or other materials containing more than 1 percent free silica shall not be used as...

  20. 30 CFR 72.610 - Abrasive blasting.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed... mines. Silica sand or other materials containing more than 1 percent free silica shall not be used as...

  1. 30 CFR 72.610 - Abrasive blasting.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed... mines. Silica sand or other materials containing more than 1 percent free silica shall not be used as...

  2. 30 CFR 72.610 - Abrasive blasting.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed... mines. Silica sand or other materials containing more than 1 percent free silica shall not be used as...

  3. 30 CFR 72.610 - Abrasive blasting.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed... mines. Silica sand or other materials containing more than 1 percent free silica shall not be used as...

  4. Abrasion by aeolian particles: Earth and Mars

    NASA Technical Reports Server (NTRS)

    Greeley, R.; Marshall, J. R.; White, B. R.; Pollack, J. B.; Marshall, J.; Krinsley, D.

    1984-01-01

    Estimation of the rate of aeolian abrasion of rocks on Mars requires knowledge of: (1) particle flux, (2) susceptibilities to abrasion of various rocks, and (3) wind frequencies on Mars. Fluxes and susceptibilities for a wide range of conditions were obtained in the laboratory and combined with wind data from the Viking meteorology experiment. Assuming an abundant supply of sand-sized particles, estimated rates range up to 2.1 x 10 to the minus 2 power cm of abrasion per year in the vicinity of Viking Lander 1. This rate is orders of magnitude too great to be in agreement with the inferred age of the surface based on models of impact crater flux. The discrepancy in the estimated rate of abrasion and the presumed old age of the surface cannot be explained easily by changes in climate or exhumation of ancient surfaces. The primary reason is thought to be related to the agents of abrasion. At least some sand-sized (approx. 100 micrometers) grains appear to be present, as inferred from both lander and orbiter observations. High rates of abrasion occur for all experimental cases involving sands of quartz, basalt, or ash. However, previous studies have shown that sand is quickly comminuted to silt- and clay-sized grains in the martian aeolian regime. Experiments also show that these fine grains are electrostatically charged and bond together as sand-sized aggregates. Laboratory simulations of wind abrasion involving aggregates show that at impact velocities capable of destroying sand, aggregates from a protective veneer on the target surface and can give rise to extremely low abrasion rates.

  5. A physically-based abrasive wear model for composite materials

    SciTech Connect

    Lee, Gun Y.; Dharan, C.K.H.; Ritchie, Robert O.

    2001-05-01

    A simple physically-based model for the abrasive wear of composite materials is presented based on the mechanics and mechanisms associated with sliding wear in soft (ductile) matrix composites containing hard (brittle) reinforcement particles. The model is based on the assumption that any portion of the reinforcement that is removed as wear debris cannot contribute to the wear resistance of the matrix material. The size of this non-contributing portion of the reinforcement is estimated by modeling the three primary wear mechanisms, specifically plowing, interfacial cracking and particle removal. Critical variables describing the role of the reinforcement, such as its relative size and the nature of the matrix/reinforcement interface, are characterized by a single contribution coefficient, C. Predictions are compared with the results of experimental two-body (pin-on drum) abrasive wear tests performed on a model aluminum particulate-reinforced epoxy matrix composite material.

  6. [The application of air abrasion in dentistry].

    PubMed

    Mandinić, Zoran; Vulićević, Zoran R; Beloica, Milos; Radović, Ivana; Mandić, Jelena; Carević, Momir; Tekić, Jasmina

    2014-01-01

    One of the main objectives of contemporary dentistry is to preserve healthy tooth structure by applying techniques of noninvasive treatment. Air abrasion is a minimally invasive nonmechanical technique of tooth preparation that uses kinetic energy to remove carious tooth structure. A powerful narrow stream of moving aluminum-oxide particles hit the tooth surface and they abrade it without heat, vibration or noise. Variables that affect speed of cutting include air pressure, particle size, powder flow, tip's size, angle and distance from the tooth. It has been proposed that air abrasion can be used to diagnose early occlusal-surface lesions and treat them with minimal tooth preparation using magnifier. Reported advantages of air abrasion include reduced noise, vibration and sensitivity. Air abrasion cavity preparations have more rounded internal contours than those prepared with straight burs. This may increase the longevity of placed restorations because it reduces the incidence of fractures and a consequence of decreased internal stresses. However, air abrasion cannot be used for all patients, i.e. in cases involving severe dust allergy, asthma, chronic obstructive lung disease, recent extraction or other oral surgery, open wounds, advanced periodontal disease, recent placement of orthodontic appliances and oral abrasions, or subgingival caries removal. Many of these conditions increase the risk of air embolism in the oral soft tissues. Dust control is a challenge, and it necessitates the use of rubber dam, high-volume evacuation, protective masks and safety eyewear for both the patient and the therapist. PMID:24684041

  7. Dry Flowing Abrasive Decontamination Technique for Pipe Systems with Swirling Air Flow

    SciTech Connect

    Kameo, Yutaka; Nakashima, Mikio; Hirabayashi, Takakuni

    2003-10-15

    A dry abrasive decontamination method was developed for removing radioactive corrosion products from surfaces of coolant pipe systems in decommissioning of a nuclear power plant. Erosion behavior of inside surfaces of stainless and carbon steel pipes by a swirling air flow containing alumina or cast-iron grit abrasive was studied. Erosion depths of the test pipes were approximately proportional to an abrasive concentration in air and an exponent of flow rate of airstream. The experimental results indicated that the present method could keep satisfactory erosion ability of abrasives even for a large-size pipe. The present method was successfully applied to {sup 60}Co-contaminated specimens sampled from a pipe of the water cleanup system of the Japan Power Demonstration Reactor.

  8. Physiological function of gastrin-releasing peptide and neuromedin B receptors in regulating itch scratching behavior in the spinal cord of mice.

    PubMed

    Sukhtankar, Devki D; Ko, Mei-Chuan

    2013-01-01

    Pruritus (itch) is a severe side effect associated with the use of drugs as well as hepatic and hematological disorders. Previous studies in rodents suggest that bombesin receptor subtypes i.e. receptors for gastrin-releasing peptide (GRPr) and neuromedin B (NMBr) differentially regulate itch scratching. However, to what degree spinal GRPr and NMBr regulate scratching evoked by intrathecally administered bombesin-related peptides is not known. The first aim of this study was to pharmacologically compare the dose-response curves for scratching induced by intrathecally administered bombesin-related peptides versus morphine, which is known to elicit itch in humans. The second aim was to determine if spinal GRPr and NMBr selectively or generally mediate scratching behavior. Mice received intrathecal injection of bombesin (0.01-0.3 nmol), GRP (0.01-0.3 nmol), NMB (0.1-1 nmol) or morphine (0.3-3 nmol) and were observed for one hour for scratching activity. Bombesin elicited most profound scratching over one hour followed by GRP and NMB, whereas morphine failed to evoke scratching response indicating the insensitivity of mouse models to intrathecal opioid-induced itch. Intrathecal pretreatment with GRPr antagonist RC-3095 (0.03-0.1 nmol) produced a parallel rightward shift in the dose response curve of GRP-induced scratching but not NMB-induced scratching. Similarly, PD168368 (1-3 nmol) only attenuated NMB but not GRP-induced scratching. Individual or co-administration of RC-3095 and PD168368 failed to alter bombesin-evoked scratching. A higher dose of RC-3095 (0.3 nmol) generally suppressed scratching induced by all three peptides but also compromised motor function in the rotarod test. Together, these data indicate that spinal GRPr and NMBr independently drive itch neurotransmission in mice and may not mediate bombesin-induced scratching. GRPr antagonists at functionally receptor-selective doses only block spinal GRP-elicited scratching but the suppression of scratching

  9. WC-Co and Cr3C2-NiCr Coatings in Low- and High-Stress Abrasive Conditions

    NASA Astrophysics Data System (ADS)

    Kašparová, Michaela; Zahálka, František; Houdková, Šárka

    2011-03-01

    The article deals with the evaluation of abrasive wear resistance and adhesive strength of thermally sprayed coatings. The main attention was paid to differences between low- and high-stress abrasive conditions of the measuring. Conclusions include the evaluation of specific properties of the WC-Co and the Cr3C2-NiCr High Velocity Oxygen Fuel coatings and the evaluation of the changes in the behavior of the abrasive media. Mainly, the relationship between the low- and high-stress abrasion conditions and the wear mechanism in the tested materials was described. For the wear test, the abrasive media of Al2O3 and SiO2 sands were chosen. During wear tests, the volume loss of the tested materials and the surface roughness of the wear tracks were measured. The wear tracks on the tested materials and abrasive sands' morphologies were observed using Scanning Electron Microscopy. It was found that high-stress abrasive conditions change the coatings' behavior very significantly, particularly that of the Cr3C2-NiCr coating. Adhesive-cohesive properties of the coatings and relationships among individual structure particles were evaluated using tensile testing. It was found that the weak bond strength among the individual splats, structure particles, and phases plays a role in the poor wear resistance of the coatings.

  10. Air abrasion: an old technology reborn.

    PubMed

    Berry, E A; Eakle, W S; Summitt, J B

    1999-08-01

    Recently, air abrasion has experienced a rebirth in restorative dentistry. Originally developed in the late 1940s, the principle of air abrasion is the imparting of kinetic energy to tiny aluminum oxide particles that are projected by a stream of compressed air or gas and expelled from a small nozzle. The force generated by the relatively hard particles striking a relatively hard surface is sufficient to cut into that surface. In the last decade, more than a dozen models of air abrasion units have been introduced into the marketplace and more are on the way. Manufacturers have developed air abrasion instruments that offer a broad range of features, from small table-top units to self-contained systems with compressors, vacuums, and curing lights. The costs range dramatically--from $1,000 to $20,000 or more--depending on the complexity of the features and attachments. Manufacturers make a variety of claims to support the value of this technology to the practicing dentist. A term often used to describe one of the benefits of air abrasion is microdentistry. The claim is that smaller, less invasive tooth preparations may be accomplished using air abrasion than with a traditional bur and air turbine. This may be true in some instances, but it would certainly depend on the operator's experience and ability to visually discern fine detail. Other claims about air abrasion are that it can be used to cut into tooth structure without local anesthesia and that it should be used on all stained grooves or fissures to determine if incipient carious lesions are present. Despite the limited number of clinical studies, the popularity of air abrasion continues to grow. To gain additional insight about these claims and to see what might be on the horizon for this technology, I spoke with three highly respected educators who are recognized for their expertise in air abrasion. What they said should give the reader a better understanding of how air abrasion might augment restorative

  11. Weldability of an abrasion-resistant steel

    SciTech Connect

    Adonyi, Y.; Domis, W.F.; Chen, C.C.

    1995-12-31

    The welding performance of a low-carbon-equivalent, abrasion-resistant steel newly developed for the mining industry was studied using a combination of simulative and actual weldability tests. The susceptibility to hydrogen-induced cracking in the weld-metal and heat-affected zones (HAZ), as well as the potential loss of strength and toughness in the HAZ, were evaluated. Simulative testing included the use of the Gleeble 1500 thermomechanical simulator to produce single and multiple-pass weld HAZ microstructures on CVN-size specimens. The effects of heat input, interpass temperature, and post-weld heat treatment (PWHT) on the HAZ microstructure and properties were determined. Additionally, a computer software was used to predict theoretical HAZ hardnesses and volume fraction of phases as a function of cooling rates. The actual welding tests included the Gapped Bead-on-Plate and the Y-groove tests to determine the weld-metal and HAZ susceptibility to hydrogen-induced cracking. Three heat inputs, two diffusible hydrogen and two weld-metal yield-strength levels were used for the actual welding stage. Good correlation was found between microstructure predictions, physical simulations, and actual weld testing results. The new steel was found to be highly weldable because of the low preheat required to avoid HAZ hydrogen induced cracking. All aspects of weld-metal and HAZ cracking behavior had to be addressed for a complete weldability characterization. It was also found that use of excessive heat inputs and PWHT should be avoided when welding this type of steels.

  12. Scratch And Dig Measurement - A Way Ahead

    NASA Astrophysics Data System (ADS)

    Baker, Lionel R.

    1987-03-01

    Although a worrying problem ever since optical components were first produced, the measurement of imperfections on optical components has become more acute in the last few years due to an increase in international trade, the more widespread use of laser optics and the trend towards automation in component production. Quite apart from their functional effect on certain classes of component, visible signs of surface damage have a direct impact on perceived quality and therefore customer acceptability of the product. This paper reviews previous attempts to quantify scratches and digs in relation to a variety of different so-called standard artefacts and discusses the extent to which these attempts have met with the approval of quality engineers and customers and are therefore likely to form a satisfactory basis for embodiment in an international standard. The results of recent surveys, supported by laboratory trials, conclude that all current national standard procedures dealing with surface imperfections produce an uncertainty of measurement in excess of levels normally regarded as acceptable by quality engineers. The reasons for this large uncertainty of measurement are discussed and a suggestion made for a new approach to the measurement of scratches based on photometric rather than geometric considerations. The reactions of potential users and the results of measurements of uncertainty using this approach indicate that it has much to offer both as a means of training inspectors and as an inspection tool for workshop use.

  13. Abrasion of eroded root dentine brushed with different toothpastes.

    PubMed

    De Menezes, Márcio; Turssi, Cecilia Pedroso; Hara, Anderson Takeo; Messias, Danielle Cristine Furtado; Serra, Mônica Campos

    2004-09-01

    This study evaluated the surface roughness change and wear provided by different dentifrices on root dentine previously exposed to erosive challenges. According to a randomized complete block design, 150 slabs of bovine root dentine (6 x 3 x 2 mm) were ground flat and polished. In an area of 4 x 3 mm on the dentine surface, specimens were submitted to five erosive/abrasive events, each one composed by: exposure to Sprite Diet or distilled water for 5 min, then to a remineralizing solution for 1 min, and simulation of 5,000 brushing strokes. Four dentifrices--regular (RE), baking soda (BS), whitening (WT) and tartar control (TC)--and distilled water (CO), used as control, were compared. Final texture and the wear depth were evaluated using a profilometer. ANOVA did not show significant interaction, indicating that the effect of dentifrices on both surface roughness change and wear did not depend on whether or not the dentine was eroded ( p>0.05). There was no difference between abrasion of eroded and sound dentine. The Tukey's test revealed that WT, BS and TC provided the highest increase in surface roughness differing from RE and CO. TC yielded the deepest wear of root dentine, whereas RE and CO, the shallowest. No significant difference in wear among BS, TC and WT were observed. Within the limitations of this study, the data showed that abrasion of both eroded and sound root dentine was dependent on the dentifrice used. PMID:15146320

  14. Preparation of Fe-doped colloidal SiO(2) abrasives and their chemical mechanical polishing behavior on sapphire substrates.

    PubMed

    Lei, Hong; Gu, Qian; Chen, Ruling; Wang, Zhanyong

    2015-08-20

    Abrasives are one of key influencing factors on surface quality during chemical mechanical polishing (CMP). Silica sol, a widely used abrasive in CMP slurries for sapphire substrates, often causes lower material removal rate (MRRs). In the present paper, Fe-doped colloidal SiO2 composite abrasives were prepared by a seed-induced growth method in order to improve the MRR of sapphire substrates. The CMP performance of Fe-doped colloidal SiO2 abrasives on sapphire substrates was investigated using UNIPOL-1502 CMP equipment. Experimental results indicate that the Fe-doped colloidal SiO2 composite abrasives exhibit lower surface roughness and higher MRR than pure colloidal SiO2 abrasives for sapphire substrates under the same testing conditions. Furthermore, the acting mechanism of Fe-doped colloidal SiO2 composite abrasives in sapphire CMP was analyzed by x-ray photoelectron spectroscopy. Analytical results show that the Fe in the composite abrasives can react with the sapphire substrates to form aluminum ferrite (AlFeO3) during CMP, which promotes the chemical effect in CMP and leads to improvement of MRR. PMID:26368752

  15. Cat-scratch disease: a wide spectrum of clinical pictures

    PubMed Central

    Mania, Anna; Kemnitz, Paweł; Figlerowicz, Magdalena; Służewski, Wojciech

    2015-01-01

    The aim of this review is to present an emerging zoonotic disease caused by Bartonella henselae. The wide spectrum of diseases connected with these bacteria varies from asymptomatic cases, to skin inflammation, fever of unknown origin, lymphadenopathy, eye disorders, encephalitis and endocarditis. The reservoirs of B. henselae are domestic animals like cats, guinea pigs, rabbits and occasionally dogs. Diagnosis is most often based on a history of exposure to cats and a serologic test with high titres of the immunoglobulin G antibody to B. henselae. Most cases of cat-scratch disease are self-limited and do not require antibiotic treatment. If an antibiotic is chosen, however, azithromycin has been shown to speed recovery. PMID:26161064

  16. Cat-scratch disease: a wide spectrum of clinical pictures.

    PubMed

    Mazur-Melewska, Katarzyna; Mania, Anna; Kemnitz, Paweł; Figlerowicz, Magdalena; Służewski, Wojciech

    2015-06-01

    The aim of this review is to present an emerging zoonotic disease caused by Bartonella henselae. The wide spectrum of diseases connected with these bacteria varies from asymptomatic cases, to skin inflammation, fever of unknown origin, lymphadenopathy, eye disorders, encephalitis and endocarditis. The reservoirs of B. henselae are domestic animals like cats, guinea pigs, rabbits and occasionally dogs. Diagnosis is most often based on a history of exposure to cats and a serologic test with high titres of the immunoglobulin G antibody to B. henselae. Most cases of cat-scratch disease are self-limited and do not require antibiotic treatment. If an antibiotic is chosen, however, azithromycin has been shown to speed recovery. PMID:26161064

  17. Lighthouses Illuminate the Way from Prints to Scratch Drawings.

    ERIC Educational Resources Information Center

    Skophammer, Karen

    1999-01-01

    Describes a unit on lighthouses, originally a social studies unit, in which students participate in two art projects: (1) a lighthouse printmaking activity and (2) a scratch-etch activity using lighthouses. Describes the steps for printmaking and the process of creating scratch-etch drawings. (CMK)

  18. Diamond-like carbon coatings enhance scratch resistance of bearing surfaces for use in joint arthroplasty: hard substrates outperform soft.

    PubMed

    Roy, Marcel E; Whiteside, Leo A; Katerberg, Brian J

    2009-05-01

    The purpose of this study was to test the hypotheses that diamond-like carbon (DLC) coatings will enhance the scratch resistance of a bearing surface in joint arthroplasty, and that a hard ceramic substrate will further enhance scratch resistance by reducing plastic deformation. We tested these hypotheses by applying a hard DLC coating to medical-grade cobalt chromium alloy (CoCr) and magnesia-stabilized zirconia (Mg-PSZ) femoral heads and performing scratch tests to determine the loads required to cause cohesive and adhesive fracture of the coating. Scratch tracks of DLC-coated and noncoated heads were then scanned by optical profilometry to determine scratch depth, width, and pile-up (raised edges), as measures of susceptibility to scratching. DLC-coated CoCr specimens exhibited cohesive coating fracture as wedge spallation at an average load of 9.74 N, whereas DLC-coated Mg-PSZ exhibited cohesive fracture as arc-tensile cracks and chipping at a significantly higher average load of 41.3 N (p < 0.0001). At adhesive coating fracture, DLC-CoCr delaminated at an average load of 35.2 N, whereas DLC-Mg-PSZ fractured by recovery spallation at a significantly higher average load of 46.8 N (p < 0.05). Both DLC-CoCr and DLC-Mg-PSZ specimens exhibited significantly shallower scratches and less pile-up than did uncoated specimens (p < 0.005 and p < 0.01, respectively). However, the harder ceramic substrate of DLC-Mg-PSZ better resisted plastic deformation, requiring significantly higher loads for cohesive and adhesive coating fracture. These findings supported both of our hypotheses. PMID:18985791

  19. Abrasive wear: The efects of fibres size on oil palm empty fruit bunch polyester composite

    NASA Astrophysics Data System (ADS)

    Kasolang, S.; Kalam, A.; Ahmad, M. A.; Rahman, N. A.; Suhadah, W. N.

    2012-06-01

    This paper presents an experimental investigation carried out to determine the effect of palm oil empty fruit bunch (OPEFB) fibre size in dry sliding testing of polyester composite. These composite samples were produced by mixing raw OPEFB fibre with resin. The samples were prepared at different sizes of fibre (100, 125, 180 and 250μm). Abrasion Resistance Tester (TR-600) was used to carried out abrasive wear tests in dry sliding conditions. These tests were performed at room temperature for two different loads (10 and 30N) and at a constant sliding velocity of 1.4m/s. The specific wear rates of OPEFB polyester composites were obtained. The morphology of composite surface before and after tests was also examined using 3D microscope imaging. Preliminary work on thermal distribution at the abrasive wheel point was also conducted for selected samples.

  20. An investigation into magnetic electrolytic abrasive turning

    NASA Astrophysics Data System (ADS)

    Mahdy, M. A. M.; Ismaeial, A. L.; Aly, F. F.

    2013-07-01

    The magnetic electrolytic abrasive turning (MEAT) process as a non-traditional machining is used to obtain surface finishing like mirror. MEAT provides one of the best alternatives for producing complex shapes with good finish in advanced materials used in aircraft and aerospace industries. The improvement of machining accuracy of MEAT continues to be a major challenge for modern industry. MEAT is a hybrid machining which combines two or more processes to remove material. The present research focuses on the development of precision electrochemical turning (ECT) under the effects of magnetic field and abrasives. The effect of magnetic flux density, electrochemical conditions and abrasive parameters on finishing efficiency and surface roughness are investigated. An empirical relationship is deduced.

  1. Twin and scratch detection and removal in micrograph images of Inconel 718

    NASA Astrophysics Data System (ADS)

    Jakob, Gerhard; Rinnhofer, Alfred; Bischof, Horst; Benesova, Wanda

    2006-02-01

    Grain size of forged nickel alloy is an important feature for the mechanical properties of the material. For fully automatic grain size evaluation in images of micrographs it is necessary to detect the boundaries of each grain. This grain boundary detection is influenced directly by artifacts like scratches and twins. Twins can be seen as parallel lines inside one grain, whereas a scratch can be identified as a sequence of collinear line segments that can be spread over the whole image. Both kinds of artifacts introduce artificial boundaries inside grains. To avoid wrong grain size evaluation, it is necessary to remove these artifacts prior to the size evaluation process. For the generation of boundary images various algorithms have been tested. The most stable results were achieved by grayscale reconstruction and a subsequent watershed segmentation. A modified line Hough transform with a third dimension in the Hough accumulator space, describing the distance of the parallel lines, is used to directly detect twins. Scratch detection is done by applying the standard line Hough transform followed by a rule based segment detection along the found Hough lines. The results of these operations give a detection rate of more than 90 percent for twins and more than 50 percent for scratches.

  2. Cat scratch disease in 9-year-old patient - a case report.

    PubMed

    Świątkowski, Wojciech; Rahnama, Mansur; Strzelczyk, Katarzyna; Baszak, Jakub; Sierocińska-Sawa, Jadwiga

    2016-03-01

    Cat scratch disease (CSD) - bartonellosis, is zoonosis caused by the intracellular gram negativebacterium Bartonellahenselae or Bartonellaquintana. The pathogens of this disease enter the human body usually as a consequence of a bite or scratch by young cats which are the natural source of such bacteria. The illness proceeds asymptomatically or with topical symptoms of infection such as a lump, spot or blister. Within 14 days a high fever and topical lymphadenopathy are observed. Lymph nodes are sore and start suppurating. In half of patients, these symptoms may resemble malignancy, and in single cases there are symptoms associated with the musculoskeletal system, such as: osteitis, arthitis and myositis. In paper presented case of 9 year-old girl patients, treated in Oral Surgery Unit due to odema and lymphadenopathy in right submandibular space. Primary surgical treatment of deciduous teeth was conducted without recovery. In few months follow-up, biopsy of lymph node of submandibular group was taken and provisional diagnosis of cat scratch disease was set. Patient was referred to the Infectious Diseases Unit where serological test confirmed cat scratch disease, and pharmacological treatment was conducted with success and recovery of young patient. PMID:27213258

  3. Enhanced scratching elicited by a pruritogen and an algogen in a mouse model of contact hypersensitivity

    PubMed Central

    Fua, Kai; Qu, Lintao; Shimada, Steven G.; Nie, Hong; LaMotte, Robert H.

    2014-01-01

    Chemical pruritogens and algogens evoke primarily itch and pain, respectively, when administered to the skin of healthy human subjects. However, the dominant sensory quality elicited by an algesic chemical stimulus may change in patients with chronic itch where bradykinin, elicits itch in addition to pain. Here we tested whether normally pruritic and algesic chemicals evoked abnormal itch- or pain-like behaviors in the mouse after the development of contact hypersensitivity (CHS), an animal model of allergic contact dermatitis. Mice previously sensitized to a hapten (squaric acid dibutylester) applied to the abdomen, exhibited spontaneous itch-like scratching and pain-like wiping directed to the site on the cheek of the CHS elicited by a subsequent challenge with the same hapten. In comparison with responses of control mice, CHS mice exhibited a significant increase in the scratching evoked by bovine adrenal medulla 8–22, a peptide that elicits a histamine-independent itch, but did not alter the scratching to histamine. Bradykinin, an algogen that elicited only wiping in control mice, additionally evoked significant scratching in CHS mice. Thus, within an area of CHS, histamine-independent itch is enhanced and chemically evoked pain is accompanied by itch. PMID:24704378

  4. Study of scratch drive actuator force characteristics

    NASA Astrophysics Data System (ADS)

    Li, Lijie; Brown, J. Gordon; Uttamchandani, Deepak

    2002-11-01

    Microactuators are one of the key components in MEMS technology, and various designs have been realized through different fabrication processes. One type of microactuator commonly used is the scratch drive actuator (SDA) that is frequently fabricated by surface micromachining processes. An experimental investigation has been conducted on the force characteristics of SDAs fabricated using the JDSU Microsystems MUMPs process. One-, two-, three- and four-plate SDAs connected to box-springs have been designed and fabricated for these experiments using MUMPs run 44. The spring constant for the box-springs has been calculated by FEM using ANSYS software. The product of the spring constant and spring extension is used to measure the forces produced by these SDAs. It is estimated that the forces produced exceed 250 μN from a one-plate SDA and 850 μN from a four-plate SDA.

  5. Scratching around mating: factors affecting anxiety in wild Lemur catta.

    PubMed

    Sclafani, Valentina; Norscia, Ivan; Antonacci, Daniela; Palagi, Elisabetta

    2012-07-01

    Scratching has been successfully used to detect anxiety, a proxy for stress, in primates, from strepsirrhines to Homo sapiens. Here, we investigated the fluctuation of scratching in Lemur catta during the mating season. In particular we evaluated whether scratching (1) varied according to sex and rank differences, (2) increased in the period of maximum stress (around the mating days), and (3) was reduced by grooming. At Berenty (South Madagascar), we followed two lemur groups (23 adult/subadult individuals) and gathered data on self-scratching, aggression, and grooming. Based on perineal area features, we recognized two periods: low swelling (LS), with no estrus female, and high swelling (HS), when at least one female was in estrus. We predicted that aggressive behaviors and anxiety-related scratching would covary. Indeed, scratching peaked in HS, when aggression was also highest. In agreement with previous literature, this result suggests that conflicts around estrus days may raise anxiety levels in the social group. We expected scratching levels to be highest in males because they aggressively compete for females and are subject to mate choice and repeated attacks by dominant females. Instead, the scratching rates were similar in males and females, probably because the high competition, which involves both sexes, dampened intersexual differences. In contrast to our prediction, scratching was not rank dependent, probably because animal ranking positions changed from LS to HS. Finally, we showed that, in ring-tailed lemurs, as well as in other primates, scratching decreases after reciprocal grooming in both periods. This finding provides the first evidence that grooming could assist in reducing anxiety in strepsirrhines. PMID:22278710

  6. Corneal Abrasions and Corneal Foreign Bodies.

    PubMed

    Ahmed, Faheem; House, Robert James; Feldman, Brad Hal

    2015-09-01

    Corneal abrasions and corneal foreign bodies are frequently encountered ophthalmological injuries that are commonly diagnosed and managed by primary care physicians. The clinical course of a corneal epithelial defect can range from a relatively benign self-healing abrasion to a potentially sight-threatening complication such as a corneal ulcer, recurrent erosion, or traumatic iritis. A detailed clinical history regarding risk factors and exposure, along with a thorough slit lamp examination with fluorescein dye are essential for proper diagnosis and treatment, as well as to rule out penetrating globe injuries. Referral to an ophthalmologist is recommended in difficult cases or if other injuries are suspected. PMID:26319343

  7. Friction and abrasion of elastomeric materials

    NASA Technical Reports Server (NTRS)

    Gent, A. N.

    1975-01-01

    An abrasion apparatus is described. Experimental measurements are reported for four representative elastomeric materials, including a typical high-quality tire tread material and a possible replacement material for aircraft tire treads based on transpolypentenamer (TPPR). Measurements are carried out at different levels of frictional work input, corresponding to different severities of wear, and at both ambient temperature and at 100 C. Results indicate the marked superiority in abrasion resistance of the material based on TPPR, especially at 100 C, in comparison with the other materials examined.

  8. Universal scaling relations for pebble abrasion

    NASA Astrophysics Data System (ADS)

    Litwin, K. L.; Jerolmack, D. J.

    2012-12-01

    The process of abrasion of gravel in bed load transport results from particle-to-particle collisions, where the energy involved is sufficient to cause chipping and spallation but not fragmentation of parent grains. The removed rock material is not infinitesimal; daughter products as large as coarse sand can be produced. Although previous work has shown that lithology, grain shape, and energy of collision are contributing factors that control abrasion rates of river-bed material, little is known regarding the relationship between these factors and diminution rates. Here we explicitly isolate and investigate how these three factors influence rates of abrasion and the size distribution of daughter products, with laboratory experiments. The apparatus is a double pendulum (Newton's cradle) that produces well-controlled binary collisions. A high-speed camera precisely measures collision energy, while mass of parent rocks. and the size and shape distributions of daughter products, are measured periodically. We examined abrasion of initially square-cut 'rocks' as they underwent successive collisions in the binary collision apparatus. We have examined mass loss rate for varied lithologies, and observe a similar power-law relationship between impact energy and mass abraded. When normalized by sensible material properties, mass loss curves for all materials collapse onto a single curve, suggesting that the underlying mechanics of abrasion for different materials are the same. The relationship does not display the linear trend expected from pure energetics, and we suggest that this is a shape effect as protruding - and hence easily eroded - corners are worn away. Analysis of daughter-product particle size distributions for different lithology fragments - including natural rocks and also bricks - show the same functional form. Surprisingly, it is the power-law relation expected for brittle materials undergoing fragmentation. This suggests that brittle fracture theory also

  9. Comparison between PEEK and Ti6Al4V concerning micro-scale abrasion wear on dental applications.

    PubMed

    Sampaio, M; Buciumeanu, M; Henriques, B; Silva, F S; Souza, J C M; Gomes, J R

    2016-07-01

    In the oral cavity, abrasive wear is predictable at exposed tooth or restorative surfaces, during mastication and tooth brushing. Also, wear can occur at contacting surfaces between the Ti-based prosthetic structures and implants in presence of abrasive compounds from food or toothpaste. Thus, the aim of this work was to compare the abrasive wear resistance of PEEK and Ti6Al4V on three-body abrasion related to different hydrated silica content and loads. Surfaces of Ti6Al4V or PEEK cylinders (8mm diameter and 4mm height) were wet ground on SiC papers and then polished with 1µm diamond paste. After that, surfaces were ultrasonically cleaned in propyl alcohol for 15min and then in distilled water for 10min. Micro-scale abrasion tests were performed at 60rpm and on different normal loads (0.4, 0.8 or 1.2N) after 600 ball revolutions using suspensions with different weight contents of hydrated silica. After abrasive tests, wear scars on flat samples were measured to quantify the wear volume and characterized by scanning electron microscope (SEM) to identify the dominant wear mechanisms. Results showed a higher volume loss rate on PEEK than that recorded on Ti6Al4V,, when subjected to three-body abrasion tests involving hydrated silica suspensions. An increase in volume loss was noted on both tested materials when the abrasive content or load was increased. PEEK was characterized by less wear resistance than that on Ti6Al4V after micro-scale abrasion wear in contact with hydrated silica particles, as commonly found in toothpastes. PMID:26849309

  10. Wear of artificial denture teeth by use of toothbrushes. Part 1: Abrasive wear of anterior teeth.

    PubMed

    Satoh, Y; Ohtani, K; Maejima, K; Morikawa, M; Matsuzu, M; Nagai, E; Toyoma, H; Ohwa, M; Ohki, K; Kaketani, M

    1990-12-01

    High-strength denture teeth (HS teeth) were developed in order to improve the hardness and wear resistance of conventional plastic denture teeth (PL teeth), while retaining their feature of easy occlusal adjustment. The objective of this study was to evaluate the abrasive wear resistance of HS teeth. We conducted wear tests and measured surface roughness using six types of anterior artificial teeth, i.e., three types of HS teeth and three types of PL teeth, the latter serving as the control. The results of the toothbrush abrasion test revealed that the HS teeth had about 5 times greater wear resistance than the PL teeth. It was also found that the type of artificial teeth and the number of abrasive wear-testing strokes had a significant (P less than 0.05) influence on the surface roughness of artificial teeth. PMID:2074493

  11. Influence of alumina and titanium dioxide coatings on abrasive wear resistance of AISI 1045 steel

    NASA Astrophysics Data System (ADS)

    Santos, A.; Remolina, A.; Marulanda, J.

    2016-02-01

    This project aims to compare the behaviour of an AISI 1045 steel's abrasive wear resistance when is covered with aluminium oxide (Al2O3) or Titanium dioxide (TiO2), of nanometric size, using the technique of thermal hot spray, which allows to directly project the suspension particles on the used substrate. The tests are performed based on the ASTM G65-04 standard (Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Apparatus). The results show that the amount of, lost material increases linearly with the travelled distance; also determined that the thermal treatment of hardening-tempering and the alumina and titanium dioxide coatings decrease in average a 12.9, 39.6 and 29.3% respectively the volume of released material during abrasive wear test.

  12. Abrasion, erosion and scuffing resistance of carbide and oxide ceramic thermal sprayed coatings for different applications

    NASA Astrophysics Data System (ADS)

    Barbezat, G.; Nicoll, A. R.; Sickinger, A.

    1993-04-01

    In the area of antiwear coatings, carbide-containing coatings and oxide ceramic coatings are applied using different thermal spray processes in the form of individual layers. In many industries these coatings have become technically significant on components where wear and friction can cause critical damage in the form of abrasion, erosion and scuffing together with corrosion. Carbide-containing and ceramic coatings have been produced with different thermal spray processes for the determination of abrasive, adhesive and erosive wear resistance. Two types of abrasion test, namely an adhesion wear test and an erosion test in water at a high velocity, were used for the characterization of wear resistance under different conditions. The coatings were also characterized with regard to microstructure, composition and fracture toughness. The influence of the thermal spraying process parameters on the microstructure is presented together with the influence of the microstructure on the behavior of the coatings under simulated service conditions.

  13. Recent progress of abrasion-resistant materials: learning from nature.

    PubMed

    Meng, Jingxin; Zhang, Pengchao; Wang, Shutao

    2016-01-21

    Abrasion-resistant materials have attracted great attention for their broad applications in industry, biomedicine and military. However, the development of abrasion-resistant materials that have with unique features such as being lightweight and flexible remains a great challenge in order to satisfy unmet demands. The outstanding performance of natural abrasion-resistant materials motivates the development of new bio-inspired abrasion-resistant materials. This review summarizes the recent progress in the investigation of natural abrasion-resistant materials to explore their general design principles (i.e., the correlation between chemical components and structural features). Following natural design principles, several artificial abrasion-resistant materials have shown unique abrasion-resistant properties. The potential challenges in the future and possible solutions for designing bio-inspired abrasion-resistant materials are also briefly discussed. PMID:26335377

  14. The Effect of Pleural Abrasion on the Treatment of Primary Spontaneous Pneumothorax: A Systematic Review of Randomized Controlled Trials

    PubMed Central

    Ming, Mo-yu; Cai, Shuang-qi; Chen, Yi-Qiang

    2015-01-01

    Background Pleural abrasion has been widely used to control the recurrence of primary spontaneous pneumothorax (PSP). However, controversy still exists regarding the advantages and disadvantages of pleural abrasion compared with other interventions in preventing the recurrence of PSP. Methods The PubMed, Embase, and Cochrane Central Register of Controlled Trials databases were searched up to December 15, 2014 to identify randomized controlled trials (RCTs) that compared the effects of pleural abrasion with those of other interventions in the treatment of PSP. The study outcomes included the PSP recurrence rate and the occurrence rate of adverse effects. Results Mechanical pleural abrasion and apical pleurectomy after thoracoscopic stapled bullectomy exhibited similarly persistent postoperative air leak occurrence rates (p = 0.978) and 1-year PSP recurrence rates (p = 0.821), whereas pleural abrasion led to reduced residual chest pain and discomfort (p = 0.001) and a smaller rate of hemothorax (p = 0.036) than did apical pleurectomy. However, the addition of minocycline pleurodesis to pleural abrasion did not reduce the pneumothorax recurrence rate compared with apical pleurectomy (3.8% for both procedures) but was associated with fewer complications. There was no statistical difference in the pneumothorax recurrence rate between mechanical pleural abrasion and chemical pleurodesis with minocycline on either an intention-to-treat basis (4 of 42 versus 0 of 42, p = 0.12; Fisher exact test) or after exclusions (2 of 40 versus 0 of 42, p = 0.24; Fisher exact test). Pleural abrasion plus minocycline pleurodesis also did not reduce the pneumothorax recurrence rate compared with pleural abrasion alone (p = 0.055). Moreover, pleural abrasion plus minocycline pleurodesis was associated with more intense acute chest pain. The postoperative overall recurrence rate in patients who underwent staple line coverage with absorbable cellulose mesh and fibrin glue was similar to that

  15. Conditions for Multi-functionality in a Rhythm Generating Network Inspired by Turtle Scratching.

    PubMed

    Snyder, Abigail C; Rubin, Jonathan E

    2015-12-01

    scratch rhythms to input changes for future experimental testing. PMID:26185063

  16. 29 CFR 1915.134 - Abrasive wheels.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... exceeded. (j) All employees using abrasive wheels shall be protected by eye protection equipment in accordance with the requirements of subpart I of this part except when adequate eye protection is afforded by eye shields which are permanently attached to the bench or floor stand....

  17. 30 CFR 58.610 - Abrasive blasting.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... miners shall use in accordance with 30 CFR 56.5005 or 57.5005 respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed in a totally enclosed device with the miner outside the device. (b) Underground areas of underground mines. Silica sand or...

  18. 30 CFR 58.610 - Abrasive blasting.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... miners shall use in accordance with 30 CFR 56.5005 or 57.5005 respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed in a totally enclosed device with the miner outside the device. (b) Underground areas of underground mines. Silica sand or...

  19. 30 CFR 58.610 - Abrasive blasting.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... miners shall use in accordance with 30 CFR 56.5005 or 57.5005 respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed in a totally enclosed device with the miner outside the device. (b) Underground areas of underground mines. Silica sand or...

  20. 30 CFR 58.610 - Abrasive blasting.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... miners shall use in accordance with 30 CFR 56.5005 or 57.5005 respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed in a totally enclosed device with the miner outside the device. (b) Underground areas of underground mines. Silica sand or...

  1. 29 CFR 1915.134 - Abrasive wheels.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... spindle speed under all conditions of normal grinding. The rated maximum speed of the wheel shall not be...) Floor stand and bench mounted abrasive wheels used for external grinding shall be provided with safety guards (protection hoods). The maximum angular exposure of the grinding wheel periphery and sides...

  2. 29 CFR 1915.134 - Abrasive wheels.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... spindle speed under all conditions of normal grinding. The rated maximum speed of the wheel shall not be...) Floor stand and bench mounted abrasive wheels used for external grinding shall be provided with safety guards (protection hoods). The maximum angular exposure of the grinding wheel periphery and sides...

  3. Evaluation and Treatment of Perioperative Corneal Abrasions

    PubMed Central

    Segal, Kira L.; Fleischut, Peter M.; Kim, Charles; Levine, Ben; Faggiani, Susan L.; Banerjee, Samprit; Gadalla, Farida; Lelli, Gary J.

    2014-01-01

    Purpose. To evaluate perioperative risk factors for corneal abrasion (CA) and to determine current care for perioperative CA in a tertiary care setting. Methods. Hospital-based, cross-sectional study. In Operating Room and Post-Anesthesia Care Units patients, a comparison of cases and controls was evaluated to elucidate risk factors, time to treatment, and most common treatments prescribed for corneal abrasions. Results. 86 cases of corneal abrasion and 89 controls were identified from the 78,542 surgical procedures performed over 2 years. Statistically significant risk factors were age (P = 0.0037), general anesthesia (P < 0.001), greater average estimated blood loss (P < 0.001), eyes taped during surgery (P < 0.001), prone position (P < 0.001), trendelenburg position (P < 0.001), and supplemental oxygen en route to and in the Post-Anesthesia Care Units (P < 0.001). Average time to complaint was 129 minutes. 94% of cases had an inpatient ophthalmology consult, with an average time to consult of 164 minutes. The most common treatment was artificial tears alone (40%), followed by combination treatment of antibiotic ointment and artificial tears (35.3%). Conclusions. Trendelenburg positioning is a novel risk factor for CA. Diagnosis and treatment of perioperative corneal abrasions by an ophthalmologist typically require three hours in the tertiary care setting. PMID:24672709

  4. 30 CFR 58.610 - Abrasive blasting.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... miners shall use in accordance with 30 CFR 56.5005 or 57.5005 respirators approved for abrasive blasting by NIOSH under 42 CFR part 84, or the operation shall be performed in a totally enclosed device with the miner outside the device. (b) Underground areas of underground mines. Silica sand or...

  5. 29 CFR 1915.134 - Abrasive wheels.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 7 2014-07-01 2014-07-01 false Abrasive wheels. 1915.134 Section 1915.134 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Tools and Related...

  6. 29 CFR 1915.134 - Abrasive wheels.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 7 2012-07-01 2012-07-01 false Abrasive wheels. 1915.134 Section 1915.134 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Tools and Related...

  7. Dust transport and abrasion assessment within simulated standing vegetation

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Crop residues are useful in protecting the top soil from depletion and abrasion due to wind erosion. A wind tunnel study was done to measure sand transport and abrasion energies within the simulated artificial standing vegetation. Wind profiles, relative abrasion energies and rates of sand dischar...

  8. Relationship between abrasive wear and microstructure of composite resins.

    PubMed

    Draughn, R A; Harrison, A

    1978-08-01

    The in vitro abrasion resistance of seven commercial composite resin restorative materials has been measured. Analysis of the composite microstructures shows that abrasion rates are dependent upon the size, hardness, and volume fraction of particles in the material. The most abrasion-resistant composites contain a high volume fraction of large, hard particles. PMID:278840

  9. 21 CFR 872.6030 - Oral cavity abrasive polishing agent.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder...

  10. 21 CFR 872.6030 - Oral cavity abrasive polishing agent.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder...

  11. 21 CFR 872.6030 - Oral cavity abrasive polishing agent.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder...

  12. 21 CFR 872.6030 - Oral cavity abrasive polishing agent.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder...

  13. 21 CFR 872.6030 - Oral cavity abrasive polishing agent.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder...

  14. Effect of carbonitride precipitates on the abrasive wear behaviour of hardfacing alloy

    NASA Astrophysics Data System (ADS)

    Yang, Ke; Yu, Shengfu; Li, Yingbin; Li, Chenglin

    2008-06-01

    Hardfacing alloy of martensitic stainless steel expect higher abradability to be achieved through the addition of nitrogen being provided by the fine scale precipitation of complex carbonitride particles. Niobium and titanium as the most effective carbonitride alloying elements were added in the Fe-Cr13-Mn-N hardfacing alloy to get carbonitride precipitates. Carbonitride was systematically studied by optical microscopy, scanning electronic microscopy and energy spectrum analysis. Abrasive wear resistance of hardfacing alloy in as-welded and heat-treated conditions was tested by using the belt abrasion test apparatus where the samples slide against the abrasive belt. It is found that carbonitride particles in the hardfacing alloy are complex of Cr, Ti and Nb distributing on the grain boundary or matrix of the hardfacing alloy with different number and size in as-welded and heat-treated conditions. A large number of carbonitrides can be precipitated with very fine size (nanoscale) after heat treatment. As a result, the homogeneous distribution of very fine carbonitride particles can significantly improve the grain-abrasion wear-resisting property of the hardfacing alloy, and the mass loss is plastic deformation with minimum depth of grooving by abrasive particles and fine delamination.

  15. Abrasion Resistance of as-Cast High-Chromium Cast Iron

    NASA Astrophysics Data System (ADS)

    Pokusová, Marcela; Berta, Igor; Šooš, Ľubomír

    2014-12-01

    High chromium cast irons are widely used as abrasion resistant materials. Their properties and wear resistance depend on carbides and on the nature of the matrix supporting these carbides. The paper presents test results of irons which contain (in wt.%) 18-22 Cr and 2-5 C, and is alloyed by 1.7 Mo + 5 Ni + 2 Mn to improve the toughness. Tests showed as-cast irons with mostly austenitic matrix achieved hardness 36-53 HRC but their relative abrasion-resistance was higher than the tool steel STN 19436 heat treated on hardness 60 HRC.

  16. Hydrothermal treatment for TiN as abrasion resistant dental implant coating and its fibroblast response.

    PubMed

    Shi, Xingling; Xu, Lingli; Munar, Melvin L; Ishikawa, Kunio

    2015-04-01

    Dental implant made of pure titanium (Ti) is prone to scratch and abrasion during routine oral hygiene procedures. This results an increase in surface roughness and therefore, facilitates the adhesion of bacteria. In severe cases, this could lead to peri-implantitis. To overcome this problem, surface modification of Ti is necessary to improve its abrasion resistance. Besides, a strong implant-gingiva interface should also be guaranteed to prevent the adhesion of bacteria. In this study, titanium nitride (TiN) coating was first prepared with gas nitriding to increase surface hardness of pure the substrate. Then, the TiN was hydrothermally treated in CaCl2 solution in order to improve its soft tissue biocompatibility. The effect of hydrothermal treatment temperature on surface properties of TiN was investigated and its biocompatibility was assessed in vitro using NIH3T3 fibroblast cell. It was determined that 120°C was the critical temperature for the hydrothermal treatment condition. Treatment below 120°C could incorporate Ca into TiN surface, oxidize TiN surface partially and then improve the wettability while preserving its morphology and hardness. Fibroblast cell attachment and proliferation were improved and cell spreading was enhanced on hydrothermally treated specimens compared with untreated ones. Improved wettability, Ca incorporation and negative surface due to interstitial N were believed to be the main reasons. Hydrothermal treatment is expected to make TiN a promising dental implant coating with excellent abrasion resistance and good soft tissue affinity. PMID:25686920

  17. Cat-scratch disease in Crete: an update

    PubMed Central

    Minadakis, Georgios; Angelakis, Emmanouil; Chochlakis, Dimosthenis; Tselentis, Yannis; Psaroulaki, Anna

    2011-01-01

    There are few epidemiological and clinical studies about the presence of cat scratch disease (CSD) on the island of Crete. The objective of this study was to analyze a large number of patients with suspected CSD to define the frequency of Bartonella infections in Crete. From January 2005 to October 2008, we studied patients with suspected CSD from hospitals in Crete. Sera of the referred patients were tested by immunofluorescence assay (IFA). For some patients, we also received lymph nodes and blood samples that we tested for the presence of Bartonella henselae by molecular assays. Overall, we tested 507 serum samples and we found 56 (11%) cases of CSD. PCR assay was positive for 2 patients; one had a B. henselae positive lymph node and the other a positive whole blood sample. Significantly more CSD cases (62.5%, 35 of 56) were reported in children than in infants and adults (P<0.05). Moreover, we identified that most cases of CSD occurred between May and September (P=0.002) and December and January. CSD is prevalent in Crete and is mostly associated with an increase in outdoor activity. PMID:24470912

  18. Partly shared spinal cord networks for locomotion and scratching.

    PubMed

    Berkowitz, Ari; Hao, Zhao-Zhe

    2011-12-01

    Animals produce a variety of behaviors using a limited number of muscles and motor neurons. Rhythmic behaviors are often generated in basic form by networks of neurons within the central nervous system, or central pattern generators (CPGs). It is known from several invertebrates that different rhythmic behaviors involving the same muscles and motor neurons can be generated by a single CPG, multiple separate CPGs, or partly overlapping CPGs. Much less is known about how vertebrates generate multiple, rhythmic behaviors involving the same muscles. The spinal cord of limbed vertebrates contains CPGs for locomotion and multiple forms of scratching. We investigated the extent of sharing of CPGs for hind limb locomotion and for scratching. We used the spinal cord of adult red-eared turtles. Animals were immobilized to remove movement-related sensory feedback and were spinally transected to remove input from the brain. We took two approaches. First, we monitored individual spinal cord interneurons (i.e., neurons that are in between sensory neurons and motor neurons) during generation of each kind of rhythmic output of motor neurons (i.e., each motor pattern). Many spinal cord interneurons were rhythmically activated during the motor patterns for forward swimming and all three forms of scratching. Some of these scratch/swim interneurons had physiological and morphological properties consistent with their playing a role in the generation of motor patterns for all of these rhythmic behaviors. Other spinal cord interneurons, however, were rhythmically activated during scratching motor patterns but inhibited during swimming motor patterns. Thus, locomotion and scratching may be generated by partly shared spinal cord CPGs. Second, we delivered swim-evoking and scratch-evoking stimuli simultaneously and monitored the resulting motor patterns. Simultaneous stimulation could cause interactions of scratch inputs with subthreshold swim inputs to produce normal swimming, acceleration

  19. The effect of heat treatment on the gouging abrasion resistance of alloy white cast irons

    NASA Astrophysics Data System (ADS)

    Are, I. R. S.; Arnold, B. K.

    1995-02-01

    A series of heat treatments was employed to vary the microstructure of four commercially important alloy white cast irons, the wear resistance of which was then assessed by the ASTM jaw-crusher gouging abrasion test. Compared with the as-cast condition, standard austenitizing treatments produced a substantial increase in hardness, a marked decrease in the retained aus-tenite content in the matrix, and, in general, a significant improvement in gouging abrasion resistance. The gouging abrasion resistance tended to decline with increasing austenitizing tem-perature, although the changes in hardness and retained austenite content varied, depending on alloy composition. Subcritical heat treatment at 500 ° following hardening reduced the retained austenite content to values less than 10 pct, and in three of the alloys it caused a significant fall in both hardness and gouging abrasion resistance. The net result of the heat treatments was the development of optimal gouging abrasion resistance at intermediate levels of retained aus-tenite. The differing responses of the alloys to both high-temperature austenitizing treatments and to subcritical heat treatments at 500 ° were related to the effects of the differing carbon and alloying-element concentrations on changes in the M s temperature and secondary carbide precipitation.

  20. Comparative Evaluation of Gingival Depigmentation using Tetrafluoroethane Cryosurgery and Gingival Abrasion Technique: Two Years Follow Up

    PubMed Central

    Kumar, Santhosh; Bhat, G. Subraya; Bhat, K. Mahalinga

    2013-01-01

    Objective: A comparative evaluation of the gingival depigmentation by using Tetrafluoroethane cryosurgery and the gingival abrasion technique – 2 years of follow up. Material and Methods: Ten systemically healthy patients who were aged 18 to 36 years were selected for the study. Tetrafluoroethane was used for the cryosurgical depigmentation and the gingival abrasion technique used a coarse flame shaped bur. The presence or absence of pigmentation was tabulated, based on the GPI (Gingival Pigmentation Index). For the statistical analysis, Freidman’s test was used. Results: The keratinization was completed within a week after the application of the cryogen and about 10 days after the gingival abrasion technique was done. The statistical analysis which was done after 90th, 180th days and 2 years. The p-value which was obtained (p<.001) showed the superiority of cryosurgery over the gingival abrasion. During the follow up period, no side effects were seen for both the techniques and the improved aesthetics was maintained upto 2 years. Conclusion: The use of cryogen Tetrafluoroethane is easy, practical and inexpensive as compared to gingival abrasion, due to its high rate of recurrence. Hence, it is more acceptable to the patients and the operator. Further studies are needed to assess the long term effectiveness of the cryosurgical method of depigmentation. PMID:23543863

  1. Comparative evaluation of enamel abrasivity by toothbrush and velcro: An in vitro scanning electron microscope study

    PubMed Central

    Ojha, Saroj Kumar; Javdekar, Sadashiv Bhaskar; Dhir, Sangeeta

    2015-01-01

    Context: Plaque control has been shown to be pivotal in maintaining the optimal periodontal health. Mechanical plaque control is the most popular option for establishing the optimal oral health. Toothbrushes have been the novel tool for mechanical cleansing. However, the abrasive potential of the toothbrushes on the enamel surface is an area in gray. Aims: The aim of this in vitro study is to evaluate the abrasivity of the toothbrush versus the velcro fasteners. Materials and Methods: The mounted teeth of both the groups were subjected to abrasion test, and the tooth surfaces were observed for the possible abrasions from the oscillating strokes (toothbrush) and frictional contacts (hook and loop velcro) and examined under the scanning electron microscope. Results: Comparative assessment of both velcro (hook and loop) and toothbrush bristles did not reveal any evidence of abrasion on the tooth specimens. Conclusions: Veclro fasteners are safe and qualitatively at par to the manual toothbrush for their efficacy and efficiency in teeth cleansing PMID:26229264

  2. Abrasion resistance of linings in filament wound composite pipe

    SciTech Connect

    Hall, S.C.

    1999-07-01

    Fiberglass filament wound composite pipe has numerous industrial applications including transportation of petroleum and natural gas. Its corrosion resistance is well known but it can be susceptible to abrasion and erosion when it is used to transport slurries or dry gas containing sand particles. However, composite pipe can be manufactured integrally with abrasion resistant linings which protect the pipe from abrasion and erosion and increase its life. Laboratory investigations were performed to determine the effect of abrasive flows through polyurea-lined and unlined glass-reinforced epoxy (GRE) pipe, ultra-high molecular weight (UHMW) polyethylene (PE) pipe, and unlined steel pipe. Results are provided for the abrasion resistance, chemical resistance, adhesion strength, elongation, tensile strength, impact resistance and hardness of selected linings. The abrasion resistance of polyurea-lined composite pipe proved to be almost as resistant to abrasion and erosion as unlined steel pipe without the electrochemical corrosion associated with steel pipe.

  3. Abrasion-Resistant Technology and its Prospect for CFB Boilers

    NASA Astrophysics Data System (ADS)

    Zheng, H.; Li, Y. J.; Wang, L. J.; Liu, S. H.; Dou, Q. R.

    In recent years, CFB boilers (CFBB) have been widely used in the commercial power plants due to its environmental benefits, high combustion efficiency, wide coal flexibility, and some other advantages. At the same time, the abrasion problem, the greatest weakness of this kind of boiler, has been gradually exposed in its application process. The abrasion, particularly on key parts such as the heating surface of water-cooled wall, furnace corners, separator entrance, seriously restricts the long-period operation ability of the CFBB. This article discusses current development status for various abrasion resistant refractory materials used in a CFBB. Some comments are provided for developing new high-performance abrasion resistant refractory materials and rapid-repaired materials according to the abrasion principle and the abrasion on different parts, as well as the economical and environmental requirements for the material. The abrasion solution and operation period of CFBB can be better improved given realization.

  4. Scratch and wear resistance of polyamide 6 reinforced with multiwall carbon nanotubes.

    PubMed

    Giraldo, Luis F; Brostow, Witold; Devaux, Eric; López, Betty L; Pérez, León D

    2008-06-01

    While carbon nanotubes have been used for a variety of purposes, it was not known whether they can improve tribological properties of polymers. Polyamide 6 (PA6) has been reinforced with 0.2, 0.5 and 1.0 wt% of multiwall carbon nanotubes (MWCNTs) by melt mixing process and characterized by scanning electron microscopy (SEM), transmission electron microscopy, thermogravimetric analysis (TGA), scratching, sliding wear and tensile testing. TGA results for the air atmosphere show that MWCNTs shift the onset of thermal degradation to higher temperatures. Sliding wear tests show that the penetration depth decreases as the concentration of carbon nanotubes increases. However, the viscoelastic healing is hampered by the MWCNTs presence and the residual depths increase at the same time. Narrower scratch groove widths are seen in SEM for composites with MWCNTs, and scratch hardness increases. Tensile tests show an increase of 27% in the Young modulus value upon addition of 1.0% of MWCNTs. The stress at yield is also higher for the nanocomposites. PMID:18681065

  5. Improvement in high stress abrasive wear property of steel by hardfacing

    SciTech Connect

    Kumar, S.; Mondal, D.P.; Khaira, H.K.; Jha, A.K.

    1999-12-01

    High stress abrasive wear behavior of mild steel, medium carbon steel, and hardfacing alloy has been studied to ascertain the extent of improvement in the wear properties after hardfacing of steel. High stress abrasive wear tests were carried out by sliding the specimen against the abrasive media consisting of silicon carbide particles, rigidly bonded on paper base and mounted on disk. Maximum wear was found in the case of mild steel followed by a medium carbon alloy steel and a hardfacing alloy. Different compositions of steels and constituent phases present led to different wear rates of the specimen. The extent of improvement in wear performance of steel due to hardfacing is quite appreciable (twice compared to mild steel). Microstructural examination of the wear surface has been carried out to understand the wear mechanism.

  6. Transport-induced abrasion of fossil reptilian teeth: Implications for the existence of Tertiary dinosaurs in the Hell Creek Formation, Montana

    NASA Astrophysics Data System (ADS)

    Argast, Scott; Farlow, James O.; Gabet, Rose M.; Brinkman, Daniel L.

    1987-10-01

    The experimental transport-induced abrasion of five fossil teeth from a crocodilian and the tyrannosaurid dinosaur Albertosaurus demonstrates that enamel-coated teeth are minimally affected by abrasion associated with sediment-transport processes. After the equivalent of 360 480 km of transport, two teeth showed slight loss of weight, scratches were developed on the surface of one tooth, there were slight enlargements of the areas between adjacent serrations of one tooth, and a pit in the exposed dentine of one tooth was abraded smooth. These changes would have been difficult to recognize if the teeth had not been examined before the start of the experiment. Our results suggest that dinosaur teeth are abraded so slowly by transport processes that they provide equivocal evidence for limited transport and reworking.

  7. Loose abrasive slurries for optical glass lapping

    SciTech Connect

    Neauport, Jerome; Destribats, Julie; Maunier, Cedric; Ambard, Chrystel; Cormont, Philippe; Pintault, B.; Rondeau, Olivier

    2010-10-20

    Loose abrasive lapping is widely used to prepare optical glass before its final polishing. We carried out a comparison of 20 different slurries from four different vendors. Slurry particle sizes and morphologies were measured. Fused silica samples were lapped with these different slurries on a single side polishing machine and characterized in terms of surface roughness and depth of subsurface damage (SSD). Effects of load, rotation speed, and slurry concentration during lapping on roughness, material removal rate, and SSD were investigated.

  8. Abrasive slurry composition for machining boron carbide

    DOEpatents

    Duran, Edward L.

    1985-01-01

    An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

  9. Abrasive slurry composition for machining boron carbide

    DOEpatents

    Duran, E.L.

    1984-11-29

    An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

  10. Predicting abrasive wear with coupled Lagrangian methods

    NASA Astrophysics Data System (ADS)

    Beck, Florian; Eberhard, Peter

    2015-05-01

    In this paper, a mesh-less approach for the simulation of a fluid with particle loading and the prediction of abrasive wear is presented. We are using the smoothed particle hydrodynamics (SPH) method for modeling the fluid and the discrete element method (DEM) for the solid particles, which represent the loading of the fluid. These Lagrangian methods are used to describe heavily sloshing fluids with their free surfaces as well as the interface between the fluid and the solid particles accurately. A Reynolds-averaged Navier-Stokes equations model is applied for handling turbulences. We are predicting abrasive wear on the boundary geometry with two different wear models taking cutting and deformation mechanisms into account. The boundary geometry is discretized with special DEM particles. In doing so, it is possible to use the same particle type for both the calculation of the boundary conditions for the SPH method as well as the DEM and for predicting the abrasive wear. After a brief introduction to the SPH method and the DEM, the handling of the boundary and the coupling of the fluid and the solid particles are discussed. Then, the applied wear models are presented and the simulation scenarios are described. The first numerical experiment is the simulation of a fluid with loading which is sloshing inside a tank. The second numerical experiment is the simulation of the impact of a free jet with loading to a simplified pelton bucket. We are especially investigating the wear patterns inside the tank and the bucket.

  11. Circular Signs of the Rock Abrasion Tool

    NASA Technical Reports Server (NTRS)

    2004-01-01

    This image was taken by Mars Exploration Rover Opportunity's front hazard-avoidance camera, providing a circular sign of the success of the rover's first grinding of a rock. The round, shallow hole seen in this image is on a rock dubbed 'McKittrick,' located in the 'El Capitan' area of the larger outcrop near Opportunity's landing site.

    Opportunity used its rock abrasion tool to grind off a patch of rock 45.5 millimeters (1.8 inches) in diameter during the 30th martian day, or sol, of its mission (Feb. 23, 2004). The grinding exposed fresh rock for close inspection by the rover's microscopic imager and two spectrometers located on its robotic arm. The Honeybee Robotics team, which designed and operates the rock abrasion tool, determined the depth of the cut at 'McKittrick' to be 4.4 millimeters (0.17 inches) deep.

    On sol 34 (Feb. 27, 2004), the rover is scheduled to grind into its second target on the 'El Capitan' area, a rock dubbed 'Guadalupe' in the upper middle part of this image. The rock abrasion tools on both Mars Exploration Rovers were supplied by Honeybee Robotics, New York, N.Y.

  12. Synthesis CNTs Particle Based Abrasive Media for Abrasive Flow Machining Process

    NASA Astrophysics Data System (ADS)

    Kumar, Sonu; Murtaza, Q.; Walia, R. S.; Dhull, S.; Tyagi, P. K.

    2016-02-01

    Abrasive flow machining (AFM) is a modem fine finishing process used for intricate and internal finishing of components or parts. It is based on flowing of viscoelastic abrasive media over the surface to be fine finished. The abrasive media is the important parameter in the AFM process because of its ability to accurately abrade the predefined area along it flow path. In this study, an attempt is made to develop a new abrasive, alumina with Carbon non tubes (CNTs) in viscoelastic medium. CNT s in house produced through chemical vapour deposition technique and characterize through TEM. Performance evaluation of the new abrasive media is carried out by increasing content of CNT s with fixed extrusion pressure, viscosity of media and media flow rate as process parameters and surface finish improvement and material removal as process responses in AFM setup. Significantly improvement has been observed in material removal and maximum improvement of 100% has been observed in the surface finish on the inner cylindrical surface of the cast iron work piece.

  13. Allergy testing - skin

    MedlinePlus

    Patch tests - allergy; Scratch tests - allergy; Skin tests - allergy; RAST test ... There are three common methods of allergy skin testing. The skin prick test involves: Placing a small amount of substances that may be causing your symptoms on the skin, ...

  14. Two-body, dry abrasive wear of Fe/Cr/C experimental alloys - relationship between microstructure and mechanical properties

    SciTech Connect

    Kwok, C.K.S.

    1982-01-01

    A systematic study of abrasive wear resistance of Fe/Cr/Mn based alloys has been carried out using a two body pin-on-disc wear machine. Abrasives used were silicon carbide, alumina and quartz. The objective of this study was to evaluate the abrasive wear resistance and to investigate the relationships between microstructure, mechanical properties, and abrasive wear resistance for these experimental alloys. Several commercial alloys were also tested to provide a basis for comparison. The goal of this study was to develop information so as to improve wear resistance of these experimental alloys by means of thermal treatments. Grain-refinement by double heat treatment was carried out in this research.

  15. Abrasive wear behavior of heat-treated ABC-silicon carbide

    SciTech Connect

    Zhang, Xiao Feng; Lee, Gun Y.; Chen, Da; Ritchie, Robert O.; De Jonghe, Lutgard C.

    2002-06-17

    Hot-pressed silicon carbide, containing aluminum, boron, and carbon additives (ABC-SiC), was subjected to three-body and two-body wear testing using diamond abrasives over a range of sizes. In general, the wear resistance of ABC-SiC, with suitable heat treatment, was superior to that of commercial SiC.

  16. Air-propelled abrasive grit for postemergence in-row weed control in field corn

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Organic growers need additional tools for weed control. A new technique involving abrasive grit propelled by compressed air was tested in field plots. Grit derived from corn cobs was directed at seedlings of summer annual weeds growing at the bases of corn plants when the corn was at differing early...

  17. Strong interactions between spinal cord networks for locomotion and scratching.

    PubMed

    Hao, Zhao-Zhe; Spardy, Lucy E; Nguyen, Edward B L; Rubin, Jonathan E; Berkowitz, Ari

    2011-10-01

    Distinct rhythmic behaviors involving a common set of motoneurons and muscles can be generated by separate central nervous system (CNS) networks, a single network, or partly overlapping networks in invertebrates. Less is known for vertebrates. Simultaneous activation of two networks can reveal overlap or interactions between them. The turtle spinal cord contains networks that generate locomotion and three forms of scratching (rostral, pocket, and caudal), having different knee-hip synergies. Here, we report that in immobilized spinal turtles, simultaneous delivery of types of stimulation, which individually evoked forward swimming and one form of scratching, could 1) increase the rhythm frequency; 2) evoke switches, hybrids, and intermediate motor patterns; 3) recruit a swim motor pattern even when the swim stimulation was reduced to subthreshold intensity; and 4) disrupt rhythm generation entirely. The strength of swim stimulation could influence the result. Thus even pocket scratching and caudal scratching, which do not share a knee-hip synergy with forward swimming, can interact with swim stimulation to alter both rhythm and pattern generation. Model simulations were used to explore the compatibility of our experimental results with hypothetical network architectures for rhythm generation. Models could reproduce experimental observations only if they included interactions between neurons involved in swim and scratch rhythm generation, with maximal consistency between simulations and experiments attained using a model architecture in which certain neurons participated actively in both swim and scratch rhythmogenesis. Collectively, these findings suggest that the spinal cord networks that generate locomotion and scratching have important shared components or strong interactions between them. PMID:21734103

  18. Defining an Abrasion Index for Lunar Surface Systems as a Function of Dust Interaction Modes and Variable Concentration Zones

    NASA Technical Reports Server (NTRS)

    Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W., Jr.

    2010-01-01

    Unexpected issues were encountered during the Apollo era of lunar exploration due to detrimental abrasion of materials upon exposure to the fine-grained, irregular shaped dust on the surface of the Moon. For critical design features involving contact with the lunar surface and for astronaut safety concerns, operational concepts and dust tolerance must be considered in the early phases of mission planning. To systematically define material selection criteria, dust interaction can be characterized by two-body or three-body abrasion testing, and subcategorically by physical interactions of compression, rolling, sliding and bending representing specific applications within the system. Two-body abrasion occurs when a single particle or asperity slides across a given surface removing or displacing material. Three-body abrasion occurs when multiple particles interact with a solid surface, or in between two surfaces, allowing the abrasives to freely rotate and interact with the material(s), leading to removal or displacement of mass. Different modes of interaction are described in this paper along with corresponding types of tests that can be utilized to evaluate each configuration. In addition to differential modes of abrasion, variable concentrations of dust in different zones can also be considered for a given system design and operational protocol. These zones include: (1) outside the habitat where extensive dust exposure occurs, (2) in a transitional zone such as an airlock or suitport, and (3) inside the habitat or spacesuit with a low particle count. These zones can be used to help define dust interaction frequencies, and corresponding risks to the systems and/or crew can be addressed by appropriate mitigation strategies. An abrasion index is introduced that includes the level of risk, R, the hardness of the mineralogy, H, the severity of the abrasion mode, S, and the frequency of particle interactions, F.

  19. Defining an abrasion index for lunar surface systems as a function of dust interaction modes and variable concentration zones

    NASA Astrophysics Data System (ADS)

    Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W.

    2011-11-01

    Unexpected issues were encountered during the Apollo era of lunar exploration due to detrimental abrasion of materials upon exposure to the fine-grained, irregular shaped dust on the surface of the Moon. For critical design features involving contact with the lunar surface and for astronaut safety concerns, operational concepts and dust tolerance must be considered in the early phases of mission planning. To systematically define material selection criteria, dust interaction can be characterized by two-body or three-body abrasion testing, and sub-categorically by physical interactions of compression, rolling, sliding, and bending representing specific applications within the system. Two-body abrasion occurs when a single particle or asperity slides across a given surface removing or displacing material. Three-body abrasion occurs when multiple particles interact with a solid surface, or in between two surfaces, allowing the abrasives to freely rotate and interact with the material(s), leading to removal or displacement of mass. Different modes of interaction are described in this paper along with corresponding types of tests that can be utilized to evaluate each configuration. In addition to differential modes of abrasion, variable concentrations of dust in different zones can also be considered for a given system design and operational protocol. These zones include (1) outside the habitat where extensive dust exposure occurs, (2) in a transitional zone such as an airlock or suitport, and (3) inside the habitat or spacesuit with a low particle count. These zones can be used to help define dust interaction frequencies, and corresponding risks to the systems and/or crew can be addressed by appropriate mitigation strategies. An abrasion index is introduced that includes the level of risk, R, the hardness of the mineralogy, H, the severity of the abrasion mode, S, and the frequency of particle interactions, F.

  20. Investigation of abrasion in Al–MgO metal matrix composites

    SciTech Connect

    Muharr em Pul; Çalin, Recep; Gül, Ferhat

    2014-12-15

    In this study, the effects of reinforcement volume fractions on abrasive wear behavior were examined in Al–MgO reinforced metal matrix composites of 5%, 10% and 15% reinforcement – volume ratios produced by melt-stirring. Abrasive wear tests were carried out by 60, 80 and 100 mesh sized Al{sub 2}O{sub 3} abrasive papers and pin-on-disc wear test apparatus under 10, 20 and 30 N loads at 0.2 m/s sliding speed. The mechanical properties such as hardness and fracture strength were determined. Subsequent to the wear tests, the microstructures of worn surfaces were examined by scanning electron microscope analyses. While increased MgO reinforcement volume fraction in the composite resulted increased hardness, fracture strength was determined to decrease. Additionally, it was found that increased MgO reinforcement volume fraction in the composite was accompanied with increased wear loss and porosity as well as reinforcement – volume ratio was identified to be significant determinants of abrasive wear behavior.

  1. Hologravure as a computer-generated and laser engraved scratch hologram

    NASA Astrophysics Data System (ADS)

    Augier, Ángel G.; Sánchez, Raúl B.

    2011-01-01

    We presented "hologravure" as the generalization of a scratch hologram, generated by computer from a three-dimensional (3D) model by using an appropriate software, and laser-drawing with a conventional engraver-laser system. For making this type of computer-generated hologram, neither diffractive optics, nor mask pattern or photo-reduction of a transparency onto a high resolution film plate is needed. The shape of a 3D virtual object is encoded in a two-dimensional (2D) multiple circular-scratch drawing. A computer program was created for generating the holograms. Hologravures representing several 3D models are engraved on different materials, and the quality of the lines traced by the CO 2 laser is considered. Sheets of acrylic, polycarbonate, glass and thermo-resistant pieces of acetate were tested. Reconstructed images of all this computer-generated and laser engraved holograms and also of computer assisted and hand-drawn scratch holograms, synthesized by means of the same software are shown.

  2. The effect of topically applied salicylic compounds on serotonin-induced scratching behaviour in hairless rats.

    PubMed

    Thomsen, J S; Simonsen, L; Benfeldt, E; Jensen, S B; Serup, J

    2002-08-01

    There is a strong need for antipruritic substances for treating itch in clinical dermatology. In one recent human study, topically applied acetylsalicylic acid has been described to rapidly decrease histamine-induced itch. We have established a model for periferally elicited pruritus by injecting serotonin into the rostral back area (neck) in rats. Using this model, we aimed to investigate the antipruritic potential of four different salicylic compounds, which all possess different skin penetration characteristics. Eighteen rats were studied for 6 weeks. Prior to serotonin injections (2 mg/ml, 50 micro l), 10 micro l of test substances was applied to a circular area 18 mm in diameter. The four substances were salicylic acid, butyl salicylate, diethylamine salicylate and salicylamide, all solubilized in dimethyl isosorbide to a concentration of 5% w/w. Diethylamine salicylate and salicylamide were previously shown to be slowly absorbed through rat skin in contrast to salicylic acid and butyl salicylate. After serotonin injections, scratching was monitored by video recording for 1.5 h. Compared with the vehicle, a lower number of scratch sequences were seen when diethylamine salicylate (P < 0.001) and salicylamide (P = 0.005) had been applied. The numbers of scratch sequences were lower with diethylamine salicylate and salicylamide than with the vehicle throughout the 1.5-h study period. We conclude that topical application of diethylamine salicylate and salicylamide could suppress serotonin-induced scratching in rats. The antipruritic effect seems to be related to the slow drug release of the two substances. The results may be clinically relevant as serotonin induces itch in humans. PMID:12190947

  3. Histamine H4 receptor antagonism reduces hapten-induced scratching behaviour but not inflammation.

    PubMed

    Rossbach, Kristine; Wendorff, Stephanie; Sander, Kerstin; Stark, Holger; Gutzmer, Ralf; Werfel, Thomas; Kietzmann, Manfred; Bäumer, Wolfgang

    2009-01-01

    Effects of the histamine H(4) receptor antagonist JNJ 7777120 (1-[(5-chloro-1H-indol-2-yl)carbonyl]-4-methylpiperazine) were tested in two models of allergic contact dermatitis. Dermatitis was induced by 2,4-dinitrochlorobenzene and toluene-2,4-diisocyanate, which differ in their Th1-Th2 profile in that way that 2,4-dinitrochlorobenzene is a classical contact allergen with a pronounced Th1-mediated inflammation, while the respiratory chemical allergen toluene-2,4-diisocyanate induces a Th2-dominated inflammation. JNJ 7777120 (15 mg/kg) administered 2 h and 30 min before and 1 h after challenge did not reduce the hapten-induced ear swelling determined 24 h after challenge. This was confirmed by histological evaluation of the ear skin. A repeated administration of the haptens to the rostral part of the back of sensitized animals resulted in a frequent scratching behaviour. An administration of JNJ 7777120 (15 mg/kg) 30 min before challenge reduced this hapten-induced scratching significantly. The H(1) receptor antagonist cetirizine also reduced the scratching bouts in sensitized mice. A combination of H(1) and H(4) receptor antagonists resulted in the strongest inhibition of scratching behaviour associated with allergic dermatitis. These results indicate that H(4) receptor antagonism fails to reduce the allergic inflammatory response but strongly inhibits allergen-induced itch. Thus, a combination of H(4) and H(1) receptor antagonism might be a new strategy to treat pruritus related to allergic diseases like atopic dermatitis. PMID:18647342

  4. A new dimension to conservative dentistry: Air abrasion

    PubMed Central

    Hegde, Vivek S; Khatavkar, Roheet A

    2010-01-01

    Air abrasion dentistry has evolved over a period of time from a new concept of an alternative means of cavity preparation to an essential means of providing a truly conservative preparation for preservation of a maximal sound tooth structure. The development of bonded restorations in combination with air abrasion dentistry provides a truly minimal intervention dentistry. This article reviews the development of air abrasion, its clinical uses, and the essential accessories required for its use. PMID:20582212

  5. Tooth length and incisal wear and growth in guinea pigs (Cavia porcellus) fed diets of different abrasiveness.

    PubMed

    Müller, J; Clauss, M; Codron, D; Schulz, E; Hummel, J; Kircher, P; Hatt, J-M

    2015-06-01

    Dental diseases are among the most important reasons for presenting guinea pigs (Cavia porcellus) and other rodents to veterinary clinics, but the aetiopathology of this disease complex is unclear. Clinicians tend to believe that the ever-growing teeth of rabbits and rodents have a constant growth that needs to be worn down by the mastication of an appropriate diet. In this study, we tested the effect of four different pelleted diets of increasing abrasiveness [due to both internal (phytoliths) and external abrasives (sand)] or whole grass hay fed for 2 weeks each in random order to 16 guinea pigs on incisor growth and wear, and tooth length of incisors and cheek teeth. There was a positive correlation between wear and growth of incisors. Tooth lengths depended both on internal and external abrasives, but only upper incisors were additionally affected by the feeding of whole hay. Diet effects were most prominent in anterior cheek teeth, in particular M1 and m1. Cheek tooth angle did not become shallower with decreasing diet abrasiveness, suggesting that a lack of dietary abrasiveness does not cause the typical 'bridge formation' of anterior cheek teeth frequently observed in guinea pigs. The findings suggest that other factors than diet abrasiveness, such as mineral imbalances and in particular hereditary malocclusion, are more likely causes for dental problems observed in this species. PMID:25041439

  6. Machining human dentin by abrasive water jet drilling.

    PubMed

    Kohorst, Philipp; Tegtmeyer, Sven; Biskup, Christian; Bach, Friedrich-Wilhelm; Stiesch, Meike

    2014-01-01

    The aim of this experimental in-vitro study was to investigate the machining of human dentin using an abrasive water jet and to evaluate the influence of different abrasives and water pressures on the removal rate. Seventy-two human teeth had been collected after extraction and randomly divided into six homogeneous groups (n=12). The teeth were processed in the area of root dentin with an industrial water jet device. Different abrasives (saccharose, sorbitol, xylitol) and water pressures (15 or 25 MPa) were used in each group. Dimensions of dentin removal were analysed using a stripe projection microscope and both drilling depth as well as volume of abrasion were recorded. Morphological analyses of the dentin cavities were performed using scanning electron microscopy (SEM). Both drilling depth and volume of abrasion were significantly influenced by the abrasive and the water pressure. Depending on these parameters, the drilling depth averaged between 142 and 378 μm; the volume of abrasion averaged between 0.07 and 0.15 mm3. Microscopic images revealed that all cavities are spherical and with clearly defined margins. Slight differences between the abrasives were found with respect to the microroughness of the surface of the cavities. The results indicate that abrasive water jet machining is a promising technique for processing human dentin. PMID:24642975

  7. The dollars and sense of selecting abrasion-resistant materials

    SciTech Connect

    Jackson, D.

    1988-05-01

    Sliding abrasion and impact damage affect mine and plant operating costs on a month-to-month, or, in some cases, day-to-day basis. Modern technology has given us the tools necessary to fight abrasion on every front - materials and techniques that are cost-effective, long-lasting, and easy to use. An inspection of abrasion-resistant materials and processes - metals; ceramics; sprayable and trowelable compounds; polyethylene; urethane; rubber; epoxy - may well provide information that could help improve your company's balance sheet. The following is a compilation of product releases, literature, and manuals offered by manufacturers of abrasion-resistant materials.

  8. Pebble Jammed in Rock Abrasion Tool

    NASA Technical Reports Server (NTRS)

    2004-01-01

    After the rock abrasion tool on NASA's Mars Exploration Rover Opportunity stopped working on sol 199 (Aug. 15, 2004), rover operators used the panoramic camera to take this image the next day for help in diagnosing the problem. The tool was closer than the camera could focus on sharply, but the image does show a dark spot just left of center, which engineers have determined is likely to be a pebble jammed between the cutting-blade rotor and the wire-brush rotor. If that diagnosis is confirmed by further analysis, the tool will likely be commanded to turn the rotors in reverse to release the pebble.

  9. Optical tools for high-throughput screening of abrasion resistance of combinatorial libraries of organic coatings

    NASA Astrophysics Data System (ADS)

    Potyrailo, Radislav A.; Chisholm, Bret J.; Olson, Daniel R.; Brennan, Michael J.; Molaison, Chris A.

    2002-02-01

    Design, validation, and implementation of an optical spectroscopic system for high-throughput analysis of combinatorially developed protective organic coatings are reported. Our approach replaces labor-intensive coating evaluation steps with an automated system that rapidly analyzes 8x6 arrays of coating elements that are deposited on a plastic substrate. Each coating element of the library is 10 mm in diameter and 2 to 5 micrometers thick. Performance of coatings is evaluated with respect to their resistance to wear abrasion because this parameter is one of the primary considerations in end-use applications. Upon testing, the organic coatings undergo changes that are impossible to quantitatively predict using existing knowledge. Coatings are abraded using industry-accepted abrasion test methods at single-or multiple-abrasion conditions, followed by high- throughput analysis of abrasion-induced light scatter. The developed automated system is optimized for the analysis of diffusively scattered light that corresponds to 0 to 30% haze. System precision of 0.1 to 2.5% relative standard deviation provides capability for the reliable ranking of coatings performance. While the system was implemented for high-throughput screening of combinatorially developed organic protective coatings for automotive applications, it can be applied to a variety of other applications where materials ranking can be achieved using optical spectroscopic tools.

  10. Particle size effects on the abrasive wear of 20 vol% SiC{sub p}/7075Al composites

    SciTech Connect

    Sheu, C.Y.; Lin, S.J.

    1996-12-01

    Discontinuously reinforced aluminum (DRA) composites have many advantages over the unreinforced aluminum alloys and have found increasing applications in the automotive industry. The wear behavior plays a very important role in DRA composites for such applications. The commonly used apparatus for studying the DRA abrasive wear include pin-on-disk, block-on-ring, and pin-on-drum. The pins or blocks are the composites and the abrasive papers are bonded onto the counter parts. The main drawback of the block-on-ring and pin-on-drum techniques is that the contact area does not remain a constant during the initial testing period. In the pin-on-disk method, the abrasive testing conditions are not easily kept identical either. The abrasive particles are prone to be blunted and smeared by composites when running a single-track test and the sliding speed is not constant when running a spiral-track test. In this study, a modified pin-on-disk apparatus was developed. During the entire testing period, the contact area remains unchanged, and the composite pin can be always abraded y fresh abrasive particles. An aluminum alloy, AA 7075 was reinforced with 20 vol% SiC{sub p} at various particle sizes (82, 59, 37, 16, and 12 {micro}m).

  11. Process for repairing large scratches on fused silica optics

    NASA Astrophysics Data System (ADS)

    Cormont, Philippe; Bourgeade, Antoine; Cavaro, Sandy; Doualle, Thomas; Gaborit, Gael; Gallais, Laurent; Rullier, Jean-Luc; Taroux, Daniel

    2015-10-01

    Scratches at the surface of fused silica optics can be detrimental for the performance of optical systems because they initiate damage on the optic but also they perturb the amplitude or phase of the transmitted laser light. Removing scratches by conventional polishing techniques can be time consuming as it is an iterative and long process, especially when hours of polishing time are required to obtain very high surface accuracy. So we have investigated ways to remove them with local laser processing. The silica is then heated at temperature higher than the softening point to heal the cracks.

  12. Scratch measurement system using machine vision: part II

    NASA Astrophysics Data System (ADS)

    Sarr, Dennis P.

    1992-03-01

    Aircraft skins and windows must not have scratches, which are unacceptable for cosmetic and structural reasons. Manual methods are inadequate in giving accurate reading and do not provide a hardcopy report. A prototype scratch measurement system (SMS) using computer vision and image analysis has been developed. This paper discusses the prototype description, novel ideas, improvements, repeatability, reproducibility, accuracy, and the calibration method. Boeing's Calibration Certification Laboratory has given the prototype a qualified certification. The SMS is portable for usage in factory or aircraft hangars anywhere in the world.

  13. Scratch as a computational modelling tool for teaching physics

    NASA Astrophysics Data System (ADS)

    Lopez, Victor; Hernandez, Maria Isabel

    2015-05-01

    The Scratch online authoring tool, which features a simple programming language that has been adapted to primary and secondary students, is being used more and more in schools as it offers students and teachers the opportunity to use a tool to build scientific models and evaluate their behaviour, just as can be done with computational modelling programs. In this article, we briefly discuss why Scratch could be a useful tool for computational modelling in the primary or secondary physics classroom, and we present practical examples of how it can be used to build a model.

  14. Microstructure and abrasion resistance of plasma sprayed titania coatings

    NASA Astrophysics Data System (ADS)

    Ctibor, P.; Neufuss, K.; Chraska, P.

    2006-12-01

    Agglomerated titania nanopowder and a “classical” titania were sprayed by the high throughput water-stabilized plasma (WSP) and thoroughly compared. Optical microscopy with image analysis as well as mercury intrusion porosimetry were used for quantification of porosity. Results indicate that the “nano” coatings in general exhibit finer pores than coatings of the “conventional” micron-sized powders. Mechanical properties such as Vickers microhardness and slurry abrasion response were measured and linked to the structural investigation. Impact of the variation in the slurry composition on wear resistance of tested coatings and on character of the wear damage is discussed. The overall results, however, suggest that the “nano” coatings properties are better only for carefully selected sets of spraying parameters, which seem to have a very important impact.

  15. Development of new bound abrasive polishers for final finishing of optical glasses

    NASA Astrophysics Data System (ADS)

    Puchebner, Birgit E.; Jacobs, Stephen D.

    1995-09-01

    Because there are no practical commercially available bound abrasive polishing media, we are developing a bound abrasive polisher for deterministic finishing of optical glasses. Several in- house formulated polishing pellets, molded laps, and ring tools have been studied. Two experimental test beds were employed. The first involved the polishing of flat optical glass parts on single pellet and molded pellet laps. The tests were conducted on a single spindle machine. The performance of in-house manufactured laps was compared to experimental and commercial formulations obtained from industry. Compositions which polished the glass below 20 angstrom rms surface roughness were selected for additional testing. The second test bed for these formulations was the Opticam SM. Materials were molded into a ring tool geometry. Although the tools polished effectively, more work is required to control surface figure during final finishing.

  16. Microwave sintering of sol-gel derived abrasive grain

    DOEpatents

    Plovnick, Ross; Celikkaya, Ahmet; Blake, Rodger D.

    1997-01-01

    A method is provided for making microwave-sintered, free flowing alpha alumina-based ceramic abrasive grain, under conditions effective to couple microwaves with calcined alpha alumina-based abrasive gain precursor and sinter it at a temperature of at least about 1150.degree. C.

  17. Soybean seedlings tolerate abrasion from air-propelled grit

    Technology Transfer Automated Retrieval System (TEKTRAN)

    New tools for controlling weeds would be useful for soybean production in organic systems. Air-propelled abrasive grit is one such tool that performs well for in-row weed control in corn, but crop safety in soybean is unknown. We examined responses to abrasion by corn-cob grit of soybean seedlings a...

  18. Sand abrasion injury and biomass partitiioning in cotton seedlings

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Wind blown soil particle abrasion negatively impacts millions of hectares of crops annually. The goal of this study was to examine the effects of wind and wind blown sand abrasion damage on cotton (Gossypium hirsutum L.) seedling biomass partitioning to leaves, stems, and roots. Seedlings of three ...

  19. 29 CFR 1926.303 - Abrasive wheels and tools.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 8 2014-07-01 2014-07-01 false Abrasive wheels and tools. 1926.303 Section 1926.303 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Tools-Hand and Power § 1926.303 Abrasive wheels and tools. (a) Power. All grinding machines shall be supplied with sufficient power to maintain...

  20. 21 CFR 872.6010 - Abrasive device and accessories.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Abrasive device and accessories. 872.6010 Section 872.6010 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and...

  1. 21 CFR 872.6010 - Abrasive device and accessories.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Abrasive device and accessories. 872.6010 Section 872.6010 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and...

  2. Sand abrasion injury and biomass partitioning in cotton seedlings

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Wind blown soil particle abrasion negatively impacts millions of hectares of crops annually. The goal of this study was to examine the effects of wind and wind blown sand abrasion damage on cotton (Gossypium hirsutum L.) seedling biomass partitioning to leaves, stems, and roots. Seedlings of three ...

  3. 29 CFR 1910.215 - Abrasive wheel machinery.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... of the American National Standard Safety Code for the Use, Care, and Protection of Abrasive Wheels... Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.215 Abrasive wheel machinery....

  4. 29 CFR 1910.215 - Abrasive wheel machinery.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... of the American National Standard Safety Code for the Use, Care, and Protection of Abrasive Wheels... Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.215 Abrasive wheel machinery....

  5. Cotton seedling abrasion and recovery from wind blown sand

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Millions of hectares of crops are exposed to wind blown sand abrasion each year and in many instances the damage is thought to be severe enough to require replanting. The goal of this study was to determine the effects of wind blown sand abrasion duration on cotton (Gossypium hirsutum L.) seedlings...

  6. 29 CFR 1910.215 - Abrasive wheel machinery.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 5 2010-07-01 2010-07-01 false Abrasive wheel machinery. 1910.215 Section 1910.215 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.215 Abrasive wheel machinery. (a... wheel in motion. (5) Excluded machinery. Natural sandstone wheels and metal, wooden, cloth, or...

  7. Sand abrasion injury and biomass partitioning in cotton seedlings

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Millions of acres of crops are exposed to wind blown sand abrasion injury each year and in many instances the damage is thought to be sufficiently severe to require replanting. The goal of this study was to determine the effects of wind blown sand abrasion duration on cotton seedlings. Seedlings of ...

  8. Gingival abrasion and recession in manual and oscillating–rotating power brush users

    PubMed Central

    Rosema, NAM; Adam, R; Grender, JM; Van der Sluijs, E; Supranoto, SC; Van der Weijden, GA

    2014-01-01

    Objective To assess gingival recession (GR) in manual and power toothbrush users and evaluate the relationship between GR and gingival abrasion scores (GA). Methods This was an observational (cross-sectional), single-centre, examiner-blind study involving a single-brushing exercise, with 181 young adult participants: 90 manual brush users and 91 oscillating–rotating power brush users. Participants were assessed for GR and GA as primary response variables. Secondary response variables were the level of gingival inflammation, plaque score reduction and brushing duration. Pearson correlation was used to describe the relationship between number of recession sites and number of abrasions. Prebrushing (baseline) and post-brushing GA and plaque scores were assessed and differences analysed using paired tests. Two-sample t-test was used to analyse group differences; ancova was used for analyses of post-brushing changes with baseline as covariate. Results Overall, 97.8% of the study population had at least one site of ≥1 mm of gingival recession. For the manual group, this percentage was 98.9%, and for the power group, this percentage was 96.7% (P = 0.621). Post-brushing, the power group showed a significantly smaller GA increase than the manual group (P = 0.004); however, there was no significant correlation between number of recession sites and number of abrasions for either group (P ≥ 0.327). Conclusions Little gingival recession was observed in either toothbrush user group; the observed GR levels were comparable. Lower post-brushing gingival abrasion levels were seen in the power group. There was no correlation between gingival abrasion as a result of brushing and the observed gingival recession following use of either toothbrush. PMID:24871587

  9. Mesenchymal stem cell-conditioned medium accelerates skin wound healing: An in vitro study of fibroblast and keratinocyte scratch assays

    SciTech Connect

    Walter, M.N.M.; Wright, K.T.; Fuller, H.R.; MacNeil, S.; Johnson, W.E.B.

    2010-04-15

    We have used in vitro scratch assays to examine the relative contribution of dermal fibroblasts and keratinocytes in the wound repair process and to test the influence of mesenchymal stem cell (MSC) secreted factors on both skin cell types. Scratch assays were established using single cell and co-cultures of L929 fibroblasts and HaCaT keratinocytes, with wound closure monitored via time-lapse microscopy. Both in serum supplemented and serum free conditions, wound closure was faster in L929 fibroblast than HaCaT keratinocyte scratch assays, and in co-culture the L929 fibroblasts lead the way in closing the scratches. MSC-CM generated under serum free conditions significantly enhanced the wound closure rate of both skin cell types separately and in co-culture, whereas conditioned medium from L929 or HaCaT cultures had no significant effect. This enhancement of wound closure in the presence of MSC-CM was due to accelerated cell migration rather than increased cell proliferation. A number of wound healing mediators were identified in MSC-CM, including TGF-{beta}1, the chemokines IL-6, IL-8, MCP-1 and RANTES, and collagen type I, fibronectin, SPARC and IGFBP-7. This study suggests that the trophic activity of MSC may play a role in skin wound closure by affecting both dermal fibroblast and keratinocyte migration, along with a contribution to the formation of extracellular matrix.

  10. Effect of scratching on galvanic corrosion in oil and gas environments

    SciTech Connect

    Hara, T.; Asahi, H.; Suehiro, Y.; Kaneta, H.

    2000-02-01

    Galvanic corrosion behavior in stagnant oil and gas environments, when the metal specimens were mechanically scratched, was investigated by electrochemical methods using material combinations ranging from carbon steels to duplex stainless steels. Galvanic currents and coupled potentials increased rapidly upon mechanical scratching, immediately started to decrease, and finally returned to the values before scratching in sweet and sour environments. Therefore, an increase in the galvanic corrosion rate caused by scratching was negligibly small for the long term, and localized corrosion as a result of mechanical scratching did not occur in these stagnant solutions. The change in coupled potential immediately after scratching was small in sweet environments and large in sour environments. For rapidly forming corrosion films on less noble metals, the galvanic current after scratching decreased rapidly; however, for slowly forming corrosion films on less noble specimens, galvanic current after scratching decreased gradually.

  11. Electrophysiological Representation of Scratching CPG Activity in the Cerebellum

    PubMed Central

    Martínez-Silva, Lourdes; Manjarrez, Elias; Gutiérrez-Ospina, Gabriel; Quevedo, Jorge N.

    2014-01-01

    We analyzed the electrical activity of neuronal populations in the cerebellum and the lumbar spinal cord during fictive scratching in adult decerebrate cats before and after selective sections of the Spino-Reticulo Cerebellar Pathway (SRCP) and the Ventral-Spino Cerebellar Tract (VSCT). During fictive scratching, we found a conspicuous sinusoidal electrical activity, called Sinusoidal Cerebellar Potentials (SCPs), in the cerebellar vermis, which exhibited smaller amplitude in the paravermal and hemisphere cortices. There was also a significant spino-cerebellar coherence between these SCPs and the lumbar sinusoidal cord dorsum potentials (SCDPs). However, during spontaneous activity such spino-cerebellar coherence between spontaneous potentials recorded in the same regions decreased. We found that the section of the SRCP and the VSCT did not abolish the amplitude of the SCPs, suggesting that there are additional pathways conveying information from the spinal CPG to the cerebellum. This is the first evidence that the sinusoidal activity associated to the spinal CPG circuitry for scratching has a broad representation in the cerebellum beyond the sensory representation from hindlimbs previously described. Furthermore, the SCPs represent the global electrical activity of the spinal CPG for scratching in the cerebellar cortex. PMID:25350378

  12. Synchronization in Scratch: A Case Study with Education Science Students

    ERIC Educational Resources Information Center

    Nikolos, Dimitris; Komis, Vassilis

    2015-01-01

    The Scratch programming language is an introductory programming language for students. It is also a visual concurrent programming language, where multiple threads are executed simultaneously. Synchronization in concurrent languages is a complex task for novices to understand. Our research is focused on strategies and methods applied by novice…

  13. Scratch as a Computational Modelling Tool for Teaching Physics

    ERIC Educational Resources Information Center

    Lopez, Victor; Hernandez, Maria Isabel

    2015-01-01

    The Scratch online authoring tool, which features a simple programming language that has been adapted to primary and secondary students, is being used more and more in schools as it offers students and teachers the opportunity to use a tool to build scientific models and evaluate their behaviour, just as can be done with computational modelling…

  14. Involvement of TRPV4 in serotonin-evoked scratching

    PubMed Central

    Akiyama, Tasuku; Ivanov, Margaret; Nagamine, Masaki; Davoodi, Auva; Carstens, Mirela Iodi; Ikoma, Akihiko; Cevikbas, Ferda; Kempkes, Cordula; Buddenkotte, Joerg; Steinhoff, Martin; Carstens, E.

    2015-01-01

    Several thermo-sensitive TRP channels (TRPV1, -3; TRPA1) have been implicated in itch. In contrast, the role of transient receptor potential vanilloid type-4 (TRPV4) in itch is unknown. Therefore, we investigated if TRPV4, a temperature-sensitive cation channel, plays an important role in acute itch in mice. Four different pruritogens including serotonin (5-hydroxytrytamine, 5-HT), histamine, SLIGRL (PAR2/MrgprC11 agonist) and chloroquine (MrgprA3 agonist) were intradermally injected and itch-related scratching behavior was assessed. TRPV4 knockout (TRPV4KO) mice exhibited significantly fewer 5-HT-evoked scratching bouts compared to wild-type (WT) mice. Notably, no differences between TRPV4KO and WT mice were observed in the number of scratch bouts elicited by SLIGRL and histamine. Pretreatment with a TRPV4 antagonist significantly attenuated 5-HT-evoked scratching in vivo. Using calcium imaging in cultured primary murine dorsal root ganglion (DRG) neurons, the response of neurons after 5-HT application, but not other pruritogens, was significantly lower in TRPV4KO compared to WT mice. A TRPV4 antagonist significantly suppressed 5-HT-evoked responses in DRG cells from WT mice. Approximately 90% of 5-HT-sensitive DRG neurons were immunoreactive for an antibody to TRPV4, as assessed by calcium imaging. These results indicate that serotonin-induced itch is linked to TRPV4. PMID:26763435

  15. Preparation and characterization of poly(vinylidene fluoride)/nanoclay nanocomposite flat sheet membranes for abrasion resistance.

    PubMed

    Lai, Chi Yan; Groth, Andrew; Gray, Stephen; Duke, Mikel

    2014-06-15

    Membranes with more resilience to abrasive wear are highly desired in water treatment, especially for seawater desalination. Nanocomposite poly(vinylidene fluoride) (PVDF)/nanoclay membranes were prepared by phase inversion and then tested for abrasion resistance. Their material properties were characterized using Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), tensile testing, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Nanoclay Cloisite(®) 15A was utilised as the inorganic nanoparticle incorporated into PVDF. FTIR results showed a shifting of the PVDF crystalline phase from α to β thus indicating that the nanoclay altered the PVDF host material's structure and mechanical properties in terms of stiffness and toughness. Water permeation test showed that nanoclay at low concentration tended to reduce water flux. All nanocomposite membranes, with between 1 wt% and 5 wt% initial nanoclay loading, were more abrasion resistant than the control PVDF membrane. However, the 1 wt% exhibited superior resistance, lasting two times longer than the reference PVDF membrane under the same abrasive condition. The 1 wt% nanoclay membrane appeared less abraded by SEM observation, while also having the greatest tensile strength improvement (from 4.5 MPa to 4.9 MPa). This membrane also had the smallest agglomerated nanoclay particle size and highest toughness compared to the higher nanoclay content membranes. Nanoclays are therefore useful for improving abrasion resistance of PVDF membranes, but optimal loadings are essential to avoid losing essential mechanical properties. PMID:24698723

  16. Microfracture patterns of abrasive wear striations on teeth indicate directionality.

    PubMed

    Gordon, K R

    1984-03-01

    A method is described that will indicate the direction that an abrasive particle was traveling as it scored the surface of a brittle material. Light and scanning electron micrographs of glass, dentine, and enamel abraded by loose and, steel carbide, and diamond indicate that partial Hertzian fracture cones are formed at the margins of wear striations during abrasion. The bases of these fracture cones face in the direction of travel of the abrasive particle and, therefore, indicate directionality. Because this method is based only on the consistent geometry of fracturing of brittle materials, it is independent of the loading of the abrasive particle. The only other method available to determine directionality of striations is unreliable since it uses the width of striations, and, hence, is dependent upon a consistent loading regime of the abrasive particle. This new method has direct application for determining the direction of movement of the jaws during mastication in living or fossil animals. PMID:6731603

  17. Effects of Using Alice and Scratch in an Introductory Programming Course for Corrective Instruction

    ERIC Educational Resources Information Center

    Chang, Chih-Kai

    2014-01-01

    Scratch, a visual programming language, was used in many studies in computer science education. Most of them reported positive results by integrating Scratch into K-12 computer courses. However, the object-oriented concept, one of the important computational thinking skills, is not represented well in Scratch. Alice, another visual programming…

  18. The effect of abrasive blasting on the strength of a joint between dental porcelain and metal base.

    PubMed

    Pietnicki, Krzysztof; Wołowiec, Emilia; Klimek, Leszek

    2014-01-01

    This paper presents the effect of selected parameters of abrasive blasting on the strength of a joint between dental porcelain and metal base. Experiments were conducted for different grain sizes of abrasive material and different blasting angles, with a constant blasting pressure. InLine dental porcelain was fused on samples of cobalt-chromium alloy following abrasive blasting; they were subsequently subjected to shearing forces on a testing machine. The fractures were observed under an electron scanning microscope in order to determine the character and course of fracturing. Strength tests showed that the grain size of abrasive material was a parameter with the greatest effect on the strength. The best effects were achieved for samples subjected to abrasive blasting with material with grain size of 110 μm. No statistically significant differences were found for the strength of samples worked at different angles. The results of the fractographic examinations have shown that in all the samples, fracturing occurred mainly along the porcelain-metal boundary, with few cases of fracturing through porcelain. PMID:24708248

  19. Effect of Bioactive Glass air Abrasion on Shear Bond Strength of Two Adhesive Resins to Decalcified Enamel

    PubMed Central

    Eshghi, Alireza; Khoroushi, Maryam; Rezvani, Alireza

    2014-01-01

    Objective: Bioactive glass air abrasion is a conservative technique to remove initial decalcified tissue and caries. This study examined the shear bond strength of composite resin to sound and decalcified enamel air-abraded by bioactive glass (BAG) or alumina using etch-and-rinse and self-etch adhesives. Materials and Methods: Forty-eight permanent molars were root-amputated and sectioned mesiodistally. The obtained 96 specimens were mounted in acrylic resin; the buccal and lingual surfaces remained exposed. A demineralizing solution was used to decalcify half the specimens. Both sound and decalcified specimens were divided into two groups of alumina and bioactive glass air abrasion. In each group, the specimens were subdivided into two subgroups of Clearfil SE Bond or OptiBond FL adhesives (n=12). Composite resin cylinders were bonded on enamel surfaces cured and underwent thermocycling. The specimens were tested for shear bond strength. Data were analyzed using SPSS 16.0 and three-way ANOVA (α=0.05). Similar to the experimental groups, the enamel surface of one specimen underwent SEM evaluation. Results: No significant differences were observed in composite resin bond strength subsequent to alumina or bioactive glass air abrasion preparation techniques (P=0.987). There were no statistically significant differences between the bond strength of etch-and-rinse and self-etch adhesive groups (P=1). Also, decalcified or intact enamel groups had no significant difference (P=0.918). However, SEM analysis showed much less enamel irregularities with BAG air abrasion compared to alumina air abrasion. Conclusion: Under the limitations of this study, preparation of both intact and decalcified enamel surfaces with bioactive glass air abrasion results in similar bond strength of composite resin in comparison with alumina air abrasion using etch-&-rinse or self-etch adhesives. PMID:25628694

  20. Electrical Arc Ignition Testing of Spacesuit Materials

    NASA Technical Reports Server (NTRS)

    Smith, Sarah; Gallus, Tim; Tapia, Susana; Ball, Elizabeth; Beeson, Harold

    2006-01-01

    A viewgraph presentation on electrical arc ignition testing of spacesuit materials is shown. The topics include: 1) Background; 2) Test Objectives; 3) Test Sample Materials; 4) Test Methods; 5) Scratch Test Objectives; 6) Cotton Scratch Test Video; 7) Scratch Test Results; 8) Entire Date Plot; 9) Closeup Data Plot; 10) Scratch Test Problems; 11) Poke Test Objectives; 12) Poke Test Results; 13) Poke Test Problems; 14) Wire-break Test Objectives; 15) Cotton Wire-Break Test Video; 16) High Speed Cotton Wire-break Test Video; 17) Typical Data Plot; 18) Closeup Data Plot; 19) Wire-break Test Results; 20) Wire-break Tests vs. Scratch Tests; 21) Urethane-coated Nylon; and 22) Moleskin.

  1. Micro-scale abrasive wear behavior of medical implant material Ti-25Nb-3Mo-3Zr-2Sn alloy on various friction pairs.

    PubMed

    Wang, Zhenguo; Huang, Weijiu; Ma, Yanlong

    2014-09-01

    The micro-scale abrasion behaviors of surgical implant materials have often been reported in the literature. However, little work has been reported on the micro-scale abrasive wear behavior of Ti-25Nb-3Mo-3Zr-2Sn (TLM) titanium alloy in simulated body fluids, especially with respect to friction pairs. Therefore, a TE66 Micro-Scale Abrasion Tester was used to study the micro-scale abrasive wear behavior of the TLM alloy. This study covers the friction coefficient and wear loss of the TLM alloy induced by various friction pairs. Different friction pairs comprised of ZrO2, Si3N4 and Al2O3 ceramic balls with 25.4mm diameters were employed. The micro-scale abrasive wear mechanisms and synergistic effect between corrosion and micro-abrasion of the TLM alloy were investigated under various wear-corrosion conditions employing an abrasive, comprised of SiC (3.5 ± 0.5 μm), in two test solutions, Hanks' solution and distilled water. Before the test, the specimens were heat treated at 760°C/1.0/AC+550°C/6.0/AC. It was discovered that the friction coefficient values of the TLM alloy are larger than those in distilled water regardless of friction pairs used, because of the corrosive Hanks' solution. It was also found that the value of the friction coefficient was volatile at the beginning of wear testing, and it became more stable with further experiments. Because the ceramic balls have different properties, especially with respect to the Vickers hardness (Hv), the wear loss of the TLM alloy increased as the ball hardness increased. In addition, the wear loss of the TLM alloy in Hanks' solution was greater than that in distilled water, and this was due to the synergistic effect of micro-abrasion and corrosion, and this micro-abrasion played a leading role in the wear process. The micro-scale abrasive wear mechanism of the TLM alloy gradually changed from two-body to mixed abrasion and then to three-body abrasion as the Vickers hardness of the balls increased. PMID:25063112

  2. Mechanics, kinematics and geometry of pebble abrasion from binary collisions

    NASA Astrophysics Data System (ADS)

    Miller, K. L.; Jerolmack, D. J.

    2014-12-01

    As sediment is transported downstream as bedload, it collides with the bed causing sharp edges to chip and wear away, rounding the rock through the process of abrasion. Previous work has linked abrasion to downstream fining and rounding of grains, however, there has been little attempt to understand the underlying kinematics of abrasion. Furthermore, most studies neglect the fine particle produced during the abrasion process, as the initial grain gets smaller and rounder. In this research, we preform well-controlled laboratory experiments to determine the functional dependence between impact energy and mass lost from abrasion. We use a double-pendulum "Newton's Cradle" set-up to examine the abrasion between two grains and with a high-speed camera, we can quantify the impact energies during collision. Results from experiments verify that mass loss is proportional to kinetic energy. We define a material parameter that incorporates material density, Young's modulus, and tensile stress and show that this parameter is directly related to the proportionality between mass loss and energy. We identify an initial region of the mass loss curves in which abrasion is independent of energy and material properties; results suggest this region is determined by shape. We show that grain size distributions of daughter products are universal and independent of material; they follow a Weibull distribution, which is expected distribution from brittle fracture theory. Finally, scanning electron microscope (SEM) images show a thin damage zone near the surface, suggesting that collision energy is attenuated over some small skin depth. Overall, we find that pebble abrasion by collision can be characterized by two universal scaling relations - the mass loss versus energy curves and the size distribution of daughter products. Results will be useful for estimating expected abrasion rates in the field, and additionally demonstrate that low-energy collisions produce large quantities of sand

  3. Method for forming an abrasive surface on a tool

    DOEpatents

    Seals, Roland D.; White, Rickey L.; Swindeman, Catherine J.; Kahl, W. Keith

    1999-01-01

    A method for fabricating a tool used in cutting, grinding and machining operations, is provided. The method is used to deposit a mixture comprising an abrasive material and a bonding material on a tool surface. The materials are propelled toward the receiving surface of the tool substrate using a thermal spray process. The thermal spray process melts the bonding material portion of the mixture, but not the abrasive material. Upon impacting the tool surface, the mixture or composition solidifies to form a hard abrasive tool coating.

  4. Laser-induced damage of fused silica at 355 nm initiated at scratches

    NASA Astrophysics Data System (ADS)

    Salleo, Alberto; Genin, Francois Y.; Yoshiyama, J. M.; Stolz, Christopher J.; Kozlowski, Mark R.

    1998-04-01

    Scratches of measured width were produced on the surface of a IV grade fused silica window using a diamond tip. Two scratch morphologies were observed: plastic and brittle. The scratches were irradiated with a 355 nm laser pulse. The laser-induced damage threshold (LIDT) of the unscratched output surface was 15 J/cm2 at 3-ns. The LIDT of the scratched surface as a function of scratch width was then measured for both input and output surface scratches. Input surface scratches of width smaller than 10 micrometers did not influence the LIDT of the silica window. On the output surface, 7 $mUm wide scratches lowered the LIDT by a factor of two. For larger scratches, the LIDT reached an asymptotic value of 5 J/cm2 on both input and output surface. Possible reasons for this LIDT drop could be electric field enhancement in the cracks below the scratch, the presence of contamination particles in the scratch, or the weakening of the material because of existing mechanical flaws.

  5. Role of personality and expectations for itch and scratching induced by audiovisual itch stimuli.

    PubMed

    Schut, C; Rädel, A; Frey, L; Gieler, U; Kupfer, J

    2016-01-01

    Itch is an unpleasant, bodily sensation, which--similar to pain--evokes behavioral reactions. As a response to itch, people start scratching. There are different ways to provoke itch and subsequent scratching in experimental settings. A non-invasive method to induce itch and scratching is the presentation of itch-related (audio-) visual stimulus material, like slide-supported lectures on skin diseases or crawling insects. Also, watching videos showing other people scratching provokes itch and the desire to scratch. In this review, we focus on psychological factors, which were shown to be associated with itch and scratching provoked by (audio-) visual itch stimuli. First, we summarize the findings on the relationship between personality characteristics and (audio-) visually induced itch. Agreeableness and self-consciousness were shown to be associated with induced itch and scratching in patients with chronic skin diseases, while neuroticism was linked to induced itch in healthy subjects. Second, we present results of a recent study, in which we altered the expectations towards audio-visually induced itch and scratching by changing the information given on upcoming itch stimuli. It was shown that subjects being informed about itch stimuli in a neutral way displayed a shorter scratch duration in itch inducing situations than subjects having catastrophizing expectations. Also, the increase in scratch duration and in the number of scratch movements induced by audiovisual itch stimuli was higher when the patients were not informed about itch induction. Thus, in itch patients neither catastrophizing nor trivializing symptoms seems to be helpful. PMID:26416001

  6. Wrist actigraphy for scratch detection in the presence of confounding activities.

    PubMed

    Feuerstein, Johanna; Austin, Daniel; Sack, Robert; Hayes, Tamara L

    2011-01-01

    Scratching is a symptom of many dermatological disorders, especially atopic dermatitis. For the development of anti-itch medications, there is a need for objective measures of scratching. Wrist actigraphy (monitoring wrist and hand movements with micro-accelerometers) is a promising method for assessing scratching; however, currently available technology has a limited capacity to discriminate scratching from other similar movements. In this study, we investigated methods to improve the specificity of actigraphy for scratch detection on movement data collected from subjects using the PAM-RL actigraph. A k-means cluster analysis was used to differentiate scratching from walking and restless sleep, which are potential confounds for nighttime scratching. Features used in the analysis include variance, peak frequency, autocorrelation value at one lag, and number of counts above 0.01 g's. The k-means cluster analysis exhibited a high sensitivity (0.90 ± 0.10) and specificity for walking (0.98 ± 0.05) and restless sleep (0.88 ± 0.06), respectively, demonstrating the separability of these activities. This work indicates that the features described here can be used to develop a classifier that discriminates scratch from other activities. The described method of scratch detection shows promise as an objective method for assessing scratching movements in clinical trials and longitudinal studies of scratch. PMID:22255131

  7. The impact of the bead width on the properties of the anti-abrasion surfacing weld

    NASA Astrophysics Data System (ADS)

    Beczkowski, Robert; Gucwa, Marek; Wróbel, Joanna; Kulawik, Adam

    2016-06-01

    This work presents the results of research on the anti-abrasion surfacing welds designated to operate under wear conditions. The main purpose of the work was to produce single-layer surface welds by means of semi-automatic hard-facing/surface welding with the use of filler material containing carbide precipitate and with the use of 10mm- and 20mm- wide beads. The samples were subject to visual and penetrant testing and to destructive testing in the form of macro and micro metallographic testing, hardness testing and bend testing with a view to determine the effect which the beads of various widths have on the analysed factors.

  8. Effect of abrasive grit size on wear of manganese-zinc ferrite under three-body abrasion

    NASA Technical Reports Server (NTRS)

    Miyoshi, Kazuhisa

    1987-01-01

    Wear experiments were conducted using replication electron microscopy and reflection electron diffraction to study abrasion and deformed layers produced in single-crystal Mn-Zn ferrites under three-body abrasion. The abrasion mechanism of Mn-Zn ferrite changes drastically with the size of abrasive grits. With 15-micron (1000-mesh) SiC grits, abrasion of Mn-Zn ferrite is due principally to brittle fracture; while with 4- and 2-micron (4000- and 6000-mesh) SiC grits, abrasion is due to plastic deformation and fracture. Both microcracking and plastic flow produce polycrystalline states on the wear surfaces of single-crystal Mn-Zn ferrites. Coefficient of wear, total thickness of the deformed layers, and surface roughness of the wear surfaces increase markedly with an increase in abrasive grit size. The total thicknesses of the deformed layers are 3 microns for the ferrite abraded by 15-micron SiC, 0.9 microns for the ferrite abraded by 4-micron SiC, and 0.8 microns for the ferrite abraded by 1-micron SiC.

  9. Experimental Study on Abrasive Waterjet Polishing of Hydraulic Turbine Blades

    NASA Astrophysics Data System (ADS)

    Khakpour, H.; Birglenl, L.; Tahan, A.; Paquet, F.

    2014-03-01

    In this paper, an experimental investigation is implemented on the abrasive waterjet polishing technique to evaluate its capability in polishing of surfaces and edges of hydraulic turbine blades. For this, the properties of this method are studied and the main parameters affecting its performance are determined. Then, an experimental test-rig is designed, manufactured and tested to be used in this study. This test-rig can be used to polish linear and planar areas on the surface of the desired workpieces. Considering the number of parameters and their levels, the Taguchi method is used to design the preliminary experiments. All experiments are then implemented according to the Taguchi L18 orthogonal array. The signal-to-noise ratios obtained from the results of these experiments are used to determine the importance of the controlled polishing parameters on the final quality of the polished surface. The evaluations on these ratios reveal that the nozzle angle and the nozzle diameter have the most important impact on the results. The outcomes of these experiments can be used as a basis to design a more precise set of experiments in which the optimal values of each parameter can be estimated.

  10. Neck abscess secondary to cat-scratch disease.

    PubMed

    Dean, Robert L; Eisenbeis, John F

    2004-11-01

    A 7-year-old boy was referred to us for evaluation of an enlarging neck mass. The results of his primary care physician's initial clinical examination suggested lymphadenopathy secondary to lymphadenitis, and the patient was treated over a 4-week period with two rounds of antibiotics. However, the mass did not resolve, and it subsequently became fluctuant. The patient was referred to our institution, where we diagnosed cat-scratch disease. PMID:15628637

  11. Detecting Foreign Particles in Wind Tunnels

    NASA Technical Reports Server (NTRS)

    Sharp, H. L.; Hogenson, P. A.; Emde, W. D.

    1986-01-01

    Simple scratch test tells whether particles, which distort results, present in test. Detector developed for tests of abrasion resistance of flexible insulation blankets. Now, when detector indicates particles present in test, results interpreted accordingly. Small pits and scratches on metal foil indicate particles struck surface during wind-tunnel test. Detector used in tests of paints and coatings to determine whether abrasive particles present.

  12. Abrasive Wear Performance of Aluminium Modified Epoxy-Glass Fiber Composites

    NASA Astrophysics Data System (ADS)

    Kamble, Vikram G.; Mishra, Punyapriya; Al Dabbas, Hassan A.; Panda, H. S.; Fernandez, Johnathan Bruce

    2015-07-01

    For a long time, Aluminum filled epoxies molds have been used in rapid tooling process. These molds are very economical when applied in manufacturing of low volume of plastic parts. To improve the thermal conductivity of the material, the metallic filler material is added to it and the glass fiber improves the wear resistance of the material. These two important parameters establish the life of composites. The present work reports on abrasive wear behavior of Aluminum modified epoxy and glass fiber composite with 5 wt.% and 10 wt.% of aluminum particles. Through pin on disc wear testing machine, we studied the wear behaviors of composites, and all these samples were fabricated by using hand layup process. Epoxy resin was used as matrix material which was reinforced with Glass fiber and Aluminum as filler. The composite with 5 wt.% and 10 wt.% of Al was cast with dimensions 100 × 100 × 6 mm. The specimens were machined to a size of 6 × 6 × 4 mm for abrasive testing. Abrasive tests were carried out for different grit paper sizes, i.e., 150, 320, 600 at different sliding distance, i.e., 20, 40, 60 m at different loads of 5, 10 and 15 N and at constant speed. The weight loss due to wear was calculated along with coefficient of friction. Hardness was found using Rockwell hardness machine. The SEM morphology of the worn out surface wear was analyzed to understand the wear mechanism. Results showed that the addition of Aluminum particles was beneficial for low abrasive conditions.

  13. Improved wound healing in blue LED treated superficial abrasions

    NASA Astrophysics Data System (ADS)

    Rossi, Francesca; Tatini, Francesca; Pini, Roberto; Bacci, Stefano; De Siena, Gaetano; Cicchi, Riccardo; Pavone, Francesco; Alfieri, Domenico

    2013-06-01

    A blue-LED photocoagulator device was designed in order to induce a selective photocoagulation effect in superficial bleeding. An in vivo study in rat back skin evidenced an improved healing process in the LED treated abrasions.

  14. Scratching beneath 'The Scratching Case': systematic reviews and meta-analyses, the back door for evidence-based medicine.

    PubMed

    Simón, Carlos; Bellver, José

    2014-08-01

    Endometrial scratching or injury was first suggested a decade ago as a simple intervention to improve endometrial receptivity in patients undergoing ART. More than a decade later, based on weak evidence some doctors have adopted this strategy, although there is not yet agreement about its real benefit. In this opinion paper, we analyze the methodological and plausibility problem beneath 'the Scratching Case'. This is also applicable to several other examples of spurious associations reported in the literature. In particular, we emphasize what should be done so as not to dilute evidence-based medicine by a vicious circle created by the over-exploitation of inadequate or insufficient data to compute incorrect or incomplete conclusions. PMID:24903203

  15. Dermoscopy and Onychomycosis: guided nail abrasion for mycological samples*

    PubMed Central

    Bet, Diego Leonardo; dos Reis, Ana Lucia; Chiacchio, Nilton Di; Belda Junior, Walter

    2015-01-01

    Mycological examination is still the cornerstone for the diagnosis of onychomycosis for many dermatologists, but sampling technique interferes on its sensitivity and specificity. Nail abrasion may be used to reach the most proximal part of the lesion and can be easily accomplished with an electric abrasor. We suggest nail plate dermoscopy to identify the best location for localized abrasion to obtain adequate samples for mycological examination. PMID:26734877

  16. Dermoscopy and Onychomycosis: guided nail abrasion for mycological samples.

    PubMed

    Bet, Diego Leonardo; Reis, Ana Lucia dos; Di Chiacchio, Nilton; Belda Junior, Walter

    2015-01-01

    Mycological examination is still the cornerstone for the diagnosis of onychomycosis for many dermatologists, but sampling technique interferes on its sensitivity and specificity. Nail abrasion may be used to reach the most proximal part of the lesion and can be easily accomplished with an electric abrasor. We suggest nail plate dermoscopy to identify the best location for localized abrasion to obtain adequate samples for mycological examination. PMID:26734877

  17. Computed tomography to quantify tooth abrasion

    NASA Astrophysics Data System (ADS)

    Kofmehl, Lukas; Schulz, Georg; Deyhle, Hans; Filippi, Andreas; Hotz, Gerhard; Berndt-Dagassan, Dorothea; Kramis, Simon; Beckmann, Felix; Müller, Bert

    2010-09-01

    Cone-beam computed tomography, also termed digital volume tomography, has become a standard technique in dentistry, allowing for fast 3D jaw imaging including denture at moderate spatial resolution. More detailed X-ray images of restricted volumes for post-mortem studies in dental anthropology are obtained by means of micro computed tomography. The present study evaluates the impact of the pipe smoking wear on teeth morphology comparing the abraded tooth with its contra-lateral counterpart. A set of 60 teeth, loose or anchored in the jaw, from 12 dentitions have been analyzed. After the two contra-lateral teeth were scanned, one dataset has been mirrored before the two datasets were registered using affine and rigid registration algorithms. Rigid registration provides three translational and three rotational parameters to maximize the overlap of two rigid bodies. For the affine registration, three scaling factors are incorporated. Within the present investigation, affine and rigid registrations yield comparable values. The restriction to the six parameters of the rigid registration is not a limitation. The differences in size and shape between the tooth and its contra-lateral counterpart generally exhibit only a few percent in the non-abraded volume, validating that the contralateral tooth is a reasonable approximation to quantify, for example, the volume loss as the result of long-term clay pipe smoking. Therefore, this approach allows quantifying the impact of the pipe abrasion on the internal tooth morphology including root canal, dentin, and enamel volumes.

  18. Method of protecting surfaces from abrasion and abrasion resistant articles of manufacture

    DOEpatents

    Hirschfeld, T.B.

    1988-06-09

    Surfaces of fabricated structures are protected from damage by impacting particulates by a coating of hard material formed as a mass of thin flexible filaments having root ends secured to the surface and free portions which can flex and overlap to form a resilient cushioning mat which resembles hair or fur. The filamentary coating covers the underlying surface with hard abrasion resistance material while also being compliant and capable of local accommodation to particle impacts. The coating can also function as thermal and/or acoustical insulation and has a friction reducing effect. 11 figs.

  19. Nano-scale stick-slip friction model for the chatter scratch generated by chemical mechanical polishing process.

    PubMed

    Kim, Hong Jin; Yang, Ji Chul; Yoon, Bo Un; Lee, Hyeon-Deok; Kim, Taesung

    2012-07-01

    Although Chemical Mechanical Planarization (CMP) process is a still promising technology for the fabrication of the next generation devices, CMP-induced defects tackle further development of CMP process. In particular, even nano-sized scratches generated by CMP process kill the device directly. However mechanism of scratch formation was not clearly understood yet. CMP-induced scratches are classified as razor, chatter mark and skipping scratch. Among them, chatter mark scratch (or chatter scratch) is the most critical defect for the device yield loss. Chatter scratch has a periodic pattern of scars, which is reminiscent of a stick-slip friction pattern. Based on that similarity, stick-slip model was proposed in this paper in order to explain how chatter scratch is formed. And controlling parameters for chatter scratch are defined. During stick period the friction force that exceeds the yield strength of wafer surface makes chatter scratch and the distance between chatter marks is determined by slip period. PMID:22966633

  20. Predicting protein-peptide interactions from scratch

    NASA Astrophysics Data System (ADS)

    Yan, Chengfei; Xu, Xianjin; Zou, Xiaoqin; Zou lab Team

    Protein-peptide interactions play an important role in many cellular processes. The ability to predict protein-peptide complex structures is valuable for mechanistic investigation and therapeutic development. Due to the high flexibility of peptides and lack of templates for homologous modeling, predicting protein-peptide complex structures is extremely challenging. Recently, we have developed a novel docking framework for protein-peptide structure prediction. Specifically, given the sequence of a peptide and a 3D structure of the protein, initial conformations of the peptide are built through protein threading. Then, the peptide is globally and flexibly docked onto the protein using a novel iterative approach. Finally, the sampled modes are scored and ranked by a statistical potential-based energy scoring function that was derived for protein-peptide interactions from statistical mechanics principles. Our docking methodology has been tested on the Peptidb database and compared with other protein-peptide docking methods. Systematic analysis shows significantly improved results compared to the performances of the existing methods. Our method is computationally efficient and suitable for large-scale applications. Nsf CAREER Award 0953839 (XZ) NIH R01GM109980 (XZ).

  1. Lip rejuvenation using chemical abrasion and padding with expanded polytetrafluoroethylene implants.

    PubMed

    Mole, B

    1996-01-01

    Aesthetic improvement of the lips is a problem that must be treated in a totally independent way from the rest of the face because degeneration of the lips is tied to genetic or acquired factors for which no long-term procedure is effective. The effectiveness of resurfacing of large and small wrinkles using chemical abrasion has long been recognized. Labial padding, using supple Gore-Tex(R) implants that are cut to size and placed where necessary provides the desired result while preserving the function of the lip. Usually requested by the younger patient, it can be used in combination with chemical abrasion in the more mature patient. This technique is not only quick, tested, very effective, and definitive, but totally reversible if needed, which allows us to widen the indications with great safety. PMID:8670390

  2. Self-healing of the superhydrophobicity by ironing for the abrasion durable superhydrophobic cotton fabrics

    PubMed Central

    Wu, Jingxia; Li, Jingye; Deng, Bo; Jiang, Haiqing; Wang, Ziqiang; Yu, Ming; Li, Linfan; Xing, Chenyang; Li, Yongjin

    2013-01-01

    Self-healing of the superhydrophobic cotton fabric (SCF) obtained by the radiation-induced graft polymerization of lauryl methacrylate (LMA) and n-hexyl methacrylate (HMA), can be achieved by ironing. Through the steam ironing process, the superhydrophobicity of the SCFs will be regenerated even after the yarns are ruptured during the abrasion test under a load pressure of 44.8 kPa. SCFs made from LMA grafted cotton fabric can ultimately withstand at least 24,000 cycles of abrasion with periodic steam ironing. The FT-IR microscope results show that the migration of the polymethacrylates graft chains from the interior to the surface is responsible for the self-healing effect. PMID:24135813

  3. Atmospheric particulate emissions from dry abrasive blasting using coal slag.

    PubMed

    Kura, Bhaskar; Kambham, Kalpalatha; Sangameswaran, Sivaramakrishnan; Potana, Sandhya

    2006-08-01

    Coal slag is one of the widely used abrasives in dry abrasive blasting. Atmospheric emissions from this process include particulate matter (PM) and heavy metals, such as chromium, lead, manganese, nickel. Quantities and characteristics of PM emissions depend on abrasive characteristics and process parameters. Emission factors are key inputs to estimate emissions. Experiments were conducted to study the effect of blast pressure, abrasive feed rate, and initial surface contamination on total PM (TPM) emission factors for coal slag. Rusted and painted mild steel surfaces were used as base plates. Blasting was carried out in an enclosed chamber, and PM was collected from an exhaust duct using U.S. Environment Protection Agency source sampling methods for stationary sources. Results showed that there is significant effect of blast pressure, feed rate, and surface contamination on TPM emissions. Mathematical equations were developed to estimate emission factors in terms of mass of emissions per unit mass of abrasive used, as well as mass of emissions per unit of surface area cleaned. These equations will help industries in estimating PM emissions based on blast pressure and abrasive feed rate. In addition, emissions can be reduced by choosing optimum operating conditions. PMID:16933653

  4. Atmospheric particulate emissions from dry abrasive blasting using coal slag

    SciTech Connect

    Bhaskar Kura; Kalpalatha Kambham; Sivaramakrishnan Sangameswaran; Sandhya Potana

    2006-08-15

    Coal slag is one of the widely used abrasives in dry abrasive blasting. Atmospheric emissions from this process include particulate matter (PM) and heavy metals, such as chromium, lead, manganese, nickel. Quantities and characteristics of PM emissions depend on abrasive characteristics and process parameters. Emission factors are key inputs to estimate emissions. Experiments were conducted to study the effect of blast pressure, abrasive feed rate, and initial surface contamination on total PM (TPM) emission factors for coal slag. Rusted and painted mild steel surfaces were used as base plates. Blasting was carried out in an enclosed chamber, and PM was collected from an exhaust duct using U.S. Environment Protection Agency source sampling methods for stationary sources. Results showed that there is significant effect of blast pressure, feed rate, and surface contamination on TPM emissions. Mathematical equations were developed to estimate emission factors in terms of mass of emissions per unit mass of abrasive used, as well as mass of emissions per unit of surface area cleaned. These equations will help industries in estimating PM emissions based on blast pressure and abrasive feed rate. In addition, emissions can be reduced by choosing optimum operating conditions. 40 refs., 5 figs., 2 tabs.

  5. Analysis of Abrasive Blasting of DOP-26 Iridium Alloy

    SciTech Connect

    Ohriner, Evan Keith; Zhang, Wei; Ulrich, George B

    2012-01-01

    The effects of abrasive blasting on the surface geometry and microstructure of DOP-26 iridium alloy (Ir-0.3% W-0.006% Th 0.005% Al) have been investigated. Abrasive blasting has been used to control emissivity of components operating at elevated temperature. The effects of abrasive blasting conditions on surface morphology were investigated both experimentally and by numerical modeling. The simplified model, based on finite element analysis of a single angular particle impacting on Ir alloy disk, calculates the surface deformation and residual strain distribution. The experimental results and modeling results both indicate that the surface geometry is not sensitive to the abrasive blast process conditions of nozzle pressure and standoff distance considered in this study. On the other hand, the modeling results suggest that the angularity of the abrasive particle has an important role in determining surface geometry, which in turn, affects the emissivity. Abrasive blasting causes localized surface strains and localized recrystallization, but it does not affect grain size following extended exposure at elevated temperature. The dependence of emissivity of the DOP-26 alloy on mean surface slope follows a similar trend to that reported for pure iridium.

  6. Gingival abrasion and plaque removal with manual versus electric toothbrushing.

    PubMed

    Niemi, M L; Ainamo, J; Etemadzadeh, H

    1986-08-01

    A clinical trial was designed to test the relative numbers of gingival lesions caused during standardized brushing of the teeth of 22 volunteer dental nurse students with a manual soft multitufted, a manual soft V-shaped, and an electric toothbrush. First, the left or the right side of the jaws of each subject was brushed by a dental hygienist using the manual V-shaped or the electric brush, and the other side using the manual multitufted brush. At the 2nd brushing 1 week later, the same hygienist used the multitufted brush for brushing the side contralateral to the one in which it was used the 1st week and the V-shaped manual brush instead of the electric and vice versa. After each brushing, the number of new gingival lesions was recorded and the cleansing effect evaluated by assessment of the amount of remaining plaque. This examiner was unaware of the type of brush used. The V-shaped manual toothbrush was found to have caused more gingival abrasion than the electric toothbrush (P less than 0.005) and a similar difference was found between the multitufted manual and the electric toothbrush (P less than 0.05). There was no clinically significant difference between the plaque removing effects of the 3 brushes tested. PMID:3463575

  7. The Relationship between the Microstructure and Abrasive Resistance of a Hardfacing Alloy in the Fe-Cr-C-Nb-V System

    NASA Astrophysics Data System (ADS)

    Correa, E. O.; Alcântara, N. G.; Tecco, D. G.; Kumar, R. V.

    2007-08-01

    The relationship between abrasive wear resistance and microstructure of a hardfacing alloy based on the Fe-Cr-C-Nb-V system was investigated. This material was developed for cladding, by an open arc welding technique, of components subjected to severe abrasive wear. The work undertaken included the solidification study, microstructural characterization, and abrasion testing. Microstructural examinations of hardfaced layer showed that the microstructure of the alloy consisted of a large volume fraction of primary niobium carbides randomly dispersed in a metastable austenitic matrix containing fine M3C carbides and “islands” of eutectic mixture of γ/M7C3. Energy dispersive X-ray analysis results showed that V preferentially partitioned into the NbC and M3C phases. In comparison with the conventional high carbon/high chromium hardfacing alloy with higher hardness, a Fe-Cr-C-Nb-V hardfacing alloy exhibited improved abrasive wear resistance and a microstructure with higher toughness.

  8. Characterization of High-Temperature Abrasive Wear of Cold-Sprayed FeAl Intermetallic Compound Coating

    NASA Astrophysics Data System (ADS)

    Li, Chang-Jiu; Wang, Hong-Tao; Yang, Guan-Jun; Bao, Chong-Gao

    2011-01-01

    FeAl intermetallic compound coating was prepared by cold spraying using a mechanically alloyed Fe(Al) alloy powder followed by post-spray annealing at 950 °C. The high-temperature abrasive wear test was carried out for the FeAl coating at a temperature range from room temperature to 800 °C. The high-temperature abrasive wear of a heat-resistant stainless steel 2520 was performed for comparison. It was observed that the abrasive wear weight loss of FeAl coating was proportional to wear cycles in terms of sample revolutions at the tested temperatures. It was found that with the increase of the test temperature higher than 400 °C, the wear rate of cold-sprayed FeAl coating decreased with the increase of test temperature, while the wear rate of the heat-resistant steel increased significantly. The results indicate that the high-temperature abrasive wear resistance of the cold-sprayed FeAl intermetallic coating increased with the increase of the wear temperature in a temperature range from 400 to 800 °C. The wear resistance of cold-sprayed FeAl coating was higher than that of heat-resistant 2520 stainless steel under 800 °C by a factor of 3.

  9. CSD skin test

    MedlinePlus

    ... this page: //medlineplus.gov/ency/article/003385.htm CSD skin test To use the sharing features on this page, please enable JavaScript. The cat scratch disease (CSD) skin test was once used to help ...

  10. A novel formulation for scratch-based wear modelling in total hip arthroplasty.

    PubMed

    Kruger, Karen M; Tikekar, Nishant M; Heiner, Anneliese D; Baer, Thomas E; Lannutti, John J; Callaghan, John J; Brown, Thomas D

    2014-01-01

    Damage to the femoral head in total hip arthroplasty often takes the form of discrete scratches, which can lead to dramatic wear acceleration of the polyethylene (PE) liner. Here, a novel formulation is reported for finite element (FE) analysis of wear acceleration due to scratch damage. A diffused-light photography technique was used to globally locate areas of damage, providing guidance for usage of high-magnification optical profilometry to determine individual scratch morphology. This multiscale image combination allowed comprehensive input of scratch-based damage patterns to an FE Archard wear model, to determine the wear acceleration associated with specific retrieval femoral heads. The wear algorithm imposed correspondingly elevated wear factors on areas of PE incrementally overpassed by individual scratches. Physical validation was provided by agreement with experimental data for custom-ruled scratch patterns. Illustrative wear acceleration results are presented for four retrieval femoral heads. PMID:23305334

  11. A Novel Formulation for Scratch-Based Wear Modeling in Total Hip Arthroplasty

    PubMed Central

    Kruger, Karen M.; Tikekar, Nishant M.; Heiner, Anneliese D.; Baer, Thomas E.; Lannutti, John J.; Callaghan, John J.; Brown, Thomas D.

    2013-01-01

    Damage to the femoral head in total hip arthroplasty often takes the form of discrete scratches, which can lead to dramatic wear acceleration of the polyethylene (PE) liner. Here, a novel formulation is reported for finite element analysis of wear acceleration due to scratch damage. A diffused-light photography technique was used to globally locate areas of damage, providing guidance for usage of high-magnification optical profilometry to determine individual scratch morphology. This multiscale image combination allowed comprehensive input of scratch-based damage patterns to a finite element (FE) Archard wear model, to determine the wear acceleration associated with specific retrieval femoral heads. The wear algorithm imposed correspondingly elevated wear factors on areas of PE incrementally overpassed by individual scratches. Physical validation was provided by agreement with experimental data for custom-ruled scratch patterns. Illustrative wear acceleration results are presented for four retrieval femoral heads. PMID:23305334

  12. Biodegradation and abrasive wear of nano restorative materials.

    PubMed

    de Paula, A B; Fucio, S B P; Ambrosano, G M B; Alonso, R C B; Sardi, J C O; Puppin-Rontani, R M

    2011-01-01

    The purpose of this study was to evaluate the biomechanical degradation of two nanofilled restorative materials (a resin-modified glass ionomer, Ketac N100 and a composite, Filtek Z350), compared with conventional materials (Vitremer and TPH Spectrum). Twenty specimens obtained from each material were divided into two storage groups (n=10): relative humidity (control) and Streptococcus mutans biofilm (biodegradation). After 7 days of storage, roughness values (Ra) and micrographs by scanning electron microscopy (SEM) were obtained. In a second experimental phase, the specimens previously subjected to biodegradation were fixed to the tooth-brushing device and abraded via toothbrushes, using dentifrice slurry (mechanical degradation). Next, these specimens were washed, dried, and reassessed by roughness and SEM. The data were submitted to repeated measures three-way analysis of variance (ANOVA) and Tukey tests (p<0.05). There was statistically significant interaction among factors: material, storage (humidity/biofilm), and abrasion (before/after). After biodegradation (S mutans biofilm storage), Ketac N100 presented the highest Ra values. Concerning bio plus mechanical challenge, TPH Spectrum, Ketac N100, and Vitremer presented the undesirable roughening of their surfaces, while the nano composite Filtek Z350 exhibited the best resistance to cumulative challenges proposed. The degraded aspect after biodegradation and the exposure of fillers after mechanical degradation were visualized in micrographs. This study demonstrated that the nanotechnology incorporated in restorative materials, as in composite resin and resin-modified glass ionomer, was important for the superior resistance to biomechanical degradation. PMID:21913859

  13. Rock Cutting Depth Model Based on Kinetic Energy of Abrasive Waterjet

    NASA Astrophysics Data System (ADS)

    Oh, Tae-Min; Cho, Gye-Chun

    2016-03-01

    Abrasive waterjets are widely used in the fields of civil and mechanical engineering for cutting a great variety of hard materials including rocks, metals, and other materials. Cutting depth is an important index to estimate operating time and cost, but it is very difficult to predict because there are a number of influential variables (e.g., energy, geometry, material, and nozzle system parameters). In this study, the cutting depth is correlated to the maximum kinetic energy expressed in terms of energy (i.e., water pressure, water flow rate, abrasive feed rate, and traverse speed), geometry (i.e., standoff distance), material (i.e., α and β), and nozzle system parameters (i.e., nozzle size, shape, and jet diffusion level). The maximum kinetic energy cutting depth model is verified with experimental test data that are obtained using one type of hard granite specimen for various parameters. The results show a unique curve for a specific rock type in a power function between cutting depth and maximum kinetic energy. The cutting depth model developed here can be very useful for estimating the process time when cutting rock using an abrasive waterjet.

  14. Influence of sodium content on the properties of bioactive glasses for use in air abrasion.

    PubMed

    Farooq, Imran; Tylkowski, Maxi; Müller, Steffen; Janicki, Tomasz; Brauer, Delia S; Hill, Robert G

    2013-12-01

    Air abrasion is used in minimally invasive dentistry for preparing cavities, while removing no or little sound dentine or enamel, and the use of bioactive glass (rather than alumina) as an abrasive could aid in tooth remineralization. Melt-derived bioactive glasses (SiO2-P2O5-CaO-CaF2-Na2O) with low sodium content (0 to 10 mol% Na2O in exchange for CaO) for increased hardness, high phosphate content for high bioactivity and fluoride content for release of fluoride and formation of fluorapatite were produced, and particles between 38 and 80 µm in size were used for cutting soda-lime silicate glass microscope slides and human enamel. Vickers hardness increased with decreasing Na2O content, owing to a more compact silicate network in low sodium content glasses, resulting in shorter cutting times. Cutting times using bioactive glass were significantly longer than using the alumina control (29 µm) when tested on microscope slides; however, glasses showed more comparable results when cutting human enamel. The bioactive glasses formed apatite in Tris buffer within 6 h, which was significantly faster than Bioglass® 45S5 (24 h), suggesting that the hardness of the glasses makes them suitable for air abrasion application, while their high bioactivity and fluoride content make them of interest for tooth remineralization. PMID:24287337

  15. Microstructure and Abrasive Wear Performance of Ni-Wc Composite Microwave Clad

    NASA Astrophysics Data System (ADS)

    Bansal, Amit; Zafar, Sunny; Sharma, Apurbba Kumar

    2015-10-01

    In the present work, Ni-WC powder was deposited on mild steel substrate to develop clads through microwave hybrid heating technique. The cladding trials were carried out in an industrial microwave applicator at 1.1 kW for 540 s. The Ni-WC composite clads were characterized for microstructure and abrasive wear performance through combination of x-ray diffraction, electron and optical microscopy, microhardness, and wear tests. Phase analysis of the Ni-WC clad indicated the presence of stable carbides such as WC, W2C, Ni2W4C, and Fe6W6C. The microstructure study of the clad layer revealed the presence of a uniformly distributed interlocked WC-based reinforcement embedded in the Ni-based matrix. The average Vicker's microhardness in the clad layer was observed to be 1028 ± 90 HV, which was approximately three times the microhardness of the substrate. Abrasive wear resistance of the microwave clads was superior to the MS substrate. Abrasion was the main wear mechanism in the Ni-WC clads and the substrate samples. However, the presence of WC-based reinforcement in the composite clads reduced microcutting, resulting in enhanced wear resistance.

  16. Development of intermetallic-hardened abrasion-resistant weld hardfacing alloys

    SciTech Connect

    School, M.R.

    1986-01-01

    Chromium and cobalt are strategic materials in the US and both are major constituents in many weld hardfacing alloys. Substitution for these materials or alternatives to their use was a primary direction of this investigation which was conducted in conjunction with the US Bureau of Mines. Minimization of the use of strategic materials was the criteria guiding the development of intermetallic-hardened abrasion resistant weld hardfacing materials. Other criteria were that the new alloy contain a hard intermetallic compound in an FCC matrix, and that these intermetallic compounds be stable at room temperature. A survey of ternary systems was made and the Fe-Mo-Ni system was selected to provide a basis for alloy development. Fe-Mo-Ni alloys synthesized by arc-melting and similar alloys made by welding possessed similar microstructures, a (Fe, Ni){sub 7}Mo{sub 6} intermetallic plus austenite eutectic in an austenitic matrix. These materials exhibited poor abrasive resistance. Silicon additions to the alloy promoted formation of a Laves phase FeMoSi intermetallic which helped increase the abrasive wear resistance. Through a series of alloy chemistry iterations a final composition of Fe-20Mo-15Ni-5Si was selected. Heat treatment of this alloy at 550 to 650 C caused second phase precipitation in the matrix and raised the hardness about 14 points HRC to 50 HRC. The alloy's wear rate, measured with the pin-on-drum abrasive wear test, was 6.3 to 6.5 mg/m. However this was twice the wear rate observed in commercial high-carbon high-chromium alloys. Based on examination of the alloy microstructures, their chemistry, and an analysis of the Fe-Mo-Si phase system; directions for further research are to increase the molybdenum and silicon content to produce a Fe-20Mo-10Ni-15Si composition.

  17. The abrasion-wear resistance of arc sprayed stainless steel and composite stainless steel coatings

    SciTech Connect

    Dallaire, S.; Legoux, J.G.; Levert, H.

    1994-12-31

    Stainless steels are often used to palliate wear problems in various industries. Though they are not wear resistant, they have been used to a limited extent in applications involving both corrosive and abrasive/erosive environments. The protection of industrial components by arc sprayed stainless steel composite coatings could be considered very attractive provided these coatings offer a better wear protection than bulk stainless steel. The wear resistance of stainless steel and composite stainless steel-titanium boride coatings arc sprayed with air and argon was evaluated following the ASTM G-65 Abrasion Wear Test procedures. Wear volume loss measurements show that stainless steel coatings arc sprayed with air were slightly more resistant than bulk stainless steel while those sprayed with argon were slightly less resistant. The abrasion wear resistance of composite stainless steel-titanium diboride coatings is by two or four times beyond the wear resistance of bulk stainless steel depending upon the core wire constitution and the type of gas used for spraying. Microstructural analysis of coatings, microhardness measurements of sprayed lamellae and optical profilometry were used to characterize coatings and wear damages. Spraying with air instead of argon produced much more small particles. These particles, being removed from the metal sheath surface, are individually sprayed without diluting the concentration hard phases within cores. It results in coatings that contain large lamellae with hardnesses sufficient to withstand abrasion. By considering both the wire constitution and the spraying conditions, it was found possible to fabricate composite stainless steel coatings that show a 400% increase in wear resistance over bulk stainless steel.

  18. Material removal mechanism of 6H-SiC studied by nano-scratching with Berkovich indenter

    NASA Astrophysics Data System (ADS)

    Meng, Binbin; Zhang, Yong; Zhang, Feihu

    2016-03-01

    The aim of this paper was to analyze the deformation characteristics and material removal mechanism of mono-crystal silicon carbide. The nano-scratching tests were conducted on the surface of 6H-SiC (0001) by using Berkovich nano-indenter. In the presence of various characterization techniques, a variety of new achievements have been reached. Phase transformation behavior in the nano-scratching process of mono-crystal silicon carbide (6H-SiC) is revealed by using the transmission electron microscope in this work. Amorphous phase and dislocation activities are found near the surface area under the bottom of the scratch which stands as the major cause triggering the plastic removal of this material, with no other forms of crystalline structure found, by which the plastic removal mechanism of mono-crystal silicon carbide was well identified. With a crack-free surface that had been processed, the chip broke away from the bulk in the form of plastic mode, but the subsurface was covered by cracks with their lengths many times longer than the machined depth. The results of laser Raman indicated that residual amorphous phase exits in the chips under the condition of the plastic removal of this material.

  19. Determination of laser damage initiation probability and growth on fused silica scratches

    SciTech Connect

    Norton, M A; Carr, C W; Cross, D A; Negres, R A; Bude, J D; Steele, W A; Monticelli, M V; Suratwala, T I

    2010-10-26

    Current methods for the manufacture of optical components inevitably leaves a variety of sub-surface imperfections including scratches of varying lengths and widths on even the finest finishes. It has recently been determined that these finishing imperfections are responsible for the majority of laser-induced damage for fluences typically used in ICF class lasers. We have developed methods of engineering subscale parts with a distribution of scratches mimicking those found on full scale fused silica parts. This much higher density of scratches provides a platform to measure low damage initiation probabilities sufficient to describe damage on large scale optics. In this work, damage probability per unit scratch length was characterized as a function of initial scratch width and post fabrication processing including acid-based etch mitigation processes. The susceptibility of damage initiation density along scratches was found to be strongly affected by the post etching material removal and initial scratch width. We have developed an automated processing procedure to document the damage initiations per width and per length of theses scratches. We show here how these tools can be employed to provide predictions of the performance of full size optics in laser systems operating at 351 nm. In addition we use these tools to measure the growth rate of a damage site initiated along a scratch and compare this to the growth measured on an isolated damage site.

  20. Rock Abrasion Tool Exhibits the Deep Red Pigment of Mars

    NASA Technical Reports Server (NTRS)

    2006-01-01

    During recent soil-brushing experiments, the rock abrasion tool on NASA's Mars Exploration Rover Spirit became covered with dust, as shown here. An abundance of iron oxide minerals in the dust gave the device a reddish-brown veneer. Investigators were using the rock abrasion tool to uncover successive layers of soil in an attempt to reveal near-surface stratigraphy. Afterward, remnant dirt clods were visible on both the bit and the brush of the tool. Designers of the rock abrasion tool at Honeybee Robotics and engineers at the Jet Propulsion Laboratory developed a plan to run the brush on the rock abrasion tool in reverse to dislodge the dirt and return the tool to normal operation. Subsequent communications with the rover revealed that the procedure is working and the rock abrasion tool remains healthy.

    Spirit acquired this approximately true-color image with the panoramic camera on the rover's 893rd sol, or Martian day (July 8, 2006). The image combines exposures taken through three of the camera's filters, centered on wavelengths of 750 nanometers, 530 nanometers, and 430 nanometers.

  1. Class III Restoration of Anterior Primary Teeth: In Vitro Retention Comparison of Conventional, Modified and Air-abrasion Treated Preparations

    PubMed Central

    Asl Aminabadi, Naser; Najafpour, Ebrahim; Erfanparast, Leila; Samiei, Mohammad; Haghifar, Monireh; Sighari Deljavan, Alireza; Jamali, Zahra; Pournaghi Azar, Fatemeh; Shokravi, Marzieh

    2014-01-01

    Background and aims. Anterior esthetic restoration is challenging in pediatric dentistry, due to limited durability and poor retention of the restoration.This study assessed the effect of air abrasion on tensile failure load of composite class III restorations using different preparation techniques. Materials and methods. 100 extracted human anterior primary teeth were divided, based on the preparation methods, into four groups each consisting of 25 subjects : conventional (A), labial surface bevel (B), conventional + air abrasion (C), and labial surface bevel + air abrasion (D). After restoring cavities, tensile failure load of samples was measured in Newton by Universal testing machine at a crosshead speed of 1 mm per minute. The data were analyzed by Kruskal-Wallis and Mann Whitney U tests using SPSS software. Results. There were statistically significant differences between groups A and C (P = 0.003), groups A and B (P & 0.001), groups A and D (P & 0.001), groups B and C (P = 0.028), groups B and D (P = 0.027), and also groups C and D (P& 0.001). Group D demonstrated the highest mean tensile failure load. Conclusion. Labial surface bevel treated by air abrasion showed significantly more retention of composite restoration. PMID:25093052

  2. Development of combinatorial chemistry methods for coatings: high-throughput screening of abrasion resistance of coatings libraries.

    PubMed

    Potyrailo, Radislav A; Chisholm, Bret J; Olson, Daniel R; Brennan, Michael J; Molaison, Chris A

    2002-10-01

    Design, validation, and implementation of an optical spectroscopic system for high-throughput analysis of combinatorially developed protective organic coatings are reported. Our approach replaces labor-intensive coating evaluation steps with an automated system that rapidly analyzes 8 x 6 arrays of coating elements that are discretely deposited on a single plastic substrate. Each coating element of the library is 10 mm in diameter and 2-5 microm thick. Performance of coatings is evaluated with respect to their resistance to wear abrasion because this parameter is one of the primary considerations in end-use applications. Upon testing, the coating materials undergo changes that are impossible to quantitatively predict using existing knowledge. Coatings are abraded using industry-accepted abrasion test methods at a single or multiple abrasion conditions followed by the high-throughput analysis of abrasion-induced light scatter. The developed automated system is optimized for the analysis of diffusively scattered light that corresponds to 0-30% haze. System precision of 0.1-2.5% relative standard deviation provides capability for the reliable ranking of coatings performance. Although the system was implemented for high-throughput screening of combinatorially developed organic protective coatings for automotive applications, it can be applied for a variety of other applications for which materials ranking can be achieved using optical spectroscopic tools. PMID:12380837

  3. Finished surface texture, abrasion resistance, and porosity of Aspa glass-ionomer cement.

    PubMed

    Smales, R; Joyce, K

    1978-11-01

    1. With the finishing agents tested Concise had a smoother surface texture than Aspa. 2. The smoothest surface was on Concise polymerized against a Mylar matrix strip. The smoothest surface for Aspa was obtained with a silicon carbide disk. 3. Aspa abraded about three times as rapidly by volume as Concise when tested by a two-body abrasion method. 4. Significantly more air bubbles were entrapped by hand mixing within Aspa than within Concise. 5. Controlled clinical studies of the glass-ionomer cements are needed before they can be fully evaluated as restorative materials. PMID:281506

  4. Abrasion of Candidate Spacesuit Fabrics by Simulated Lunar Dust

    NASA Technical Reports Server (NTRS)

    Gaier, James R.; Meador, Mary Ann; Rogers, Kerry J.; Sheehy, Brennan H.

    2009-01-01

    A protocol has been developed that produced the type of lunar soil abrasion damage observed on Apollo spacesuits. This protocol was then applied to four materials (Kevlar (DuPont), Vectran (Kuraray Co., Ltd.), Orthofabric, and Tyvek (DuPont)) that are candidates for advanced spacesuits. Three of the four new candidate fabrics (all but Vectran) were effective at keeping the dust from penetrating to layers beneath. In the cases of Kevlar and Orthofabric this was accomplished by the addition of a silicone layer. In the case of Tyvek, the paper structure was dense enough to block dust transport. The least abrasive damage was suffered by the Tyvek. This was thought to be due in large part to its non-woven paper structure. The woven structures were all abraded where the top of the weave was struck by the abrasive. Of these, the Orthofabric suffered the least wear, with both Vectran and Kevlar suffering considerably more extensive filament breakage.

  5. Deformation mechanisms in advanced structural ceramics due to indentation and scratch processes

    NASA Astrophysics Data System (ADS)

    Ghosh, Dipankar

    Plasma pressure compaction technique was used to develop boron carbide (B4C) and zirconium diboride-silicon carbide (ZrB2-SiC) composite. B4C ceramics are extensively used as body armor in military and civilian applications, and ZrB2-SiC composite has been recognized as a potential candidate for high-temperature aerospace applications. In this dissertation, processing parameters, quasistatic and high-strain rate mechanical response, and fundamental deformation mechanisms of these materials have been investigated. In the case of B4C, the rate sensitivity of indentation hardness was determined using a dynamic indentation hardness tester that can deliver loads in 100 micros. By comparing dynamic hardness with the static hardness, it was found that B4C exhibits a lower hardness at high-strain rate, contrary to known behavior in many structural ceramics. However, these results are consistent with the ballistic testing of B4C armors as reported in recent literature. This behavior was further investigated using a series of spectroscopic techniques such as visible and UV micro-Raman, photoluminescence and infrared. These studies not only confirmed that structural transformation occurred during indentation experiments similar to that in ballistic testing of B4C but also suggested a greater degree of structural changes under dynamic loading compared to static loading. Due to the potential application as external heat shields in supersonic vehicles, scratch studies were conducted on the ZrB2-SiC composite. These studies revealed metal-like slip-line patterns which are indeed an unusual in brittle solids at room-temperature. Utilizing classical stress field solutions under combined normal and tangential loads, a rationale was developed for understanding the formation of scratch-induced deformation features. Also, an analytical framework was developed, combining the concept of 'blister field' and the 'secular equation' relating Raman peaks to strain, to measure scratch

  6. In vitro effect of air-abrasion operating parameters on dynamic cutting characteristics of alumina and bio-active glass powders.

    PubMed

    Milly, H; Austin, R S; Thompson, I; Banerjee, A

    2014-01-01

    Minimally invasive dentistry advocates the maintenance of all repairable tooth structures during operative caries management in combination with remineralization strategies. This study evaluated the effect of air-abrasion operating parameters on its cutting efficiency/pattern using bio-active glass (BAG) powder and alumina powder as a control in order to develop its use as a minimally invasive operative technique. The cutting efficiency/pattern assessment on an enamel analogue, Macor, was preceded by studying the powder flow rate (PFR) of two different commercial intraoral air-abrasion units with differing powder-air admix systems. The parameters tested included air pressure, powder flow rate, nozzle-substrate distance, nozzle angle, shrouding the air stream with a curtain of water, and the chemistry of abrasive powder. The abraded troughs were scanned and analyzed using confocal white light profilometry and MountainsMap surface analysis software. Data were analyzed statistically using one-way and repeated-measures analysis of variance tests (p=0.05). The air-abrasion unit using a vibration mechanism to admix the abrasive powder with the air stream exhibited a constant PFR regardless of the set air pressure. Significant differences in cutting efficiency were observed according to the tested parameters (p<0.05). Alumina powder removed significantly more material than did BAG powder. Using low air pressure and suitable consideration of the effect of air-abrasion parameters on cutting efficiency/patterns can improve the ultraconservative cutting characteristics of BAG air-abrasion, thereby allowing an introduction of this technology for the controlled cleaning/removal of enamel, where it is indicated clinically. PMID:23718212

  7. Dental abrasion pattern in a selected group of Malaysians.

    PubMed

    Yaacob, H B; Park, A W

    1990-09-01

    Among 350 inhabitants of two villages, 31 (8.9%) cleaned their teeth using table salt and charcoal applied to their forefinger or a Melastoma brush. As a result, all had distinct forms of abrasion cavity on the labial surfaces of their teeth. All of the above three agents are highly abrasive and injurious to both the hard and soft oral tissues. This dying practice is only popular among a very small number of persons in the older age group, and should be discouraged. PMID:2230960

  8. Field evidence of two-phase abrasion process

    NASA Astrophysics Data System (ADS)

    Miller, K. L.; Szabo, T.; Jerolmack, D. J.; Domokos, G.

    2013-12-01

    The rounded shape of river rocks is clear evidence that abrasion due to bed load transport is a significant agent for mass loss. Its contribution to downstream fining, however, is typically assumed to be negligible - as diminution trends may be explained solely by size-selective transport. A recent theory has predicted that pebble abrasion occurs in two well separated phases: in Phase 1, an intially-polyhedral pebble rounds to the shape of an inscribed ellipsoid without any change in axis dimensions; in Phase II, axis dimensions are slowly reduced. Importantly, Phase I abrasion means that an initially-blocky pebble may lose up to half its mass without any apparent change in 'size', which is only measured as the length of a single pebble axis by most field researchers. We hypothesize that field studies have significantly underestimated the importance of abrasion because they do not quantify pebble shape, and we set out to demonstrate that two-phase abrasion occurs in a natural stream. Our study examines downstream trends in pebble size and shape along a 10-km stretch of the Rio Mameyes within the Luquillo Critical Zone observatory, where volcaniclastic cobbles and boulders are transported by bed load at slopes up to 10%. The upper reaches of the stream consist of alluviated bedrock valleys that preclude sediment storage and thus minimize size-selective transport, which allows us to isolate the effects of abrasion. The lower 5 km is an alluvial river in which size-selective transport becomes operative. We quantified the shape and size of thousands of pebbles along the profile using hand and image-based techniques. The data provide the first field validation of two-phase abrasion; in the bedrock reaches, pebbles clearly evolve toward ellipsoids without any significant change in axis dimensions (rounding), while in the lower reaches pebbles slowly reduce their axis dimensions with little or no change in roundness. Results also show that shape metrics determined from

  9. Creating a communication system from scratch: gesture beats vocalization hands down

    PubMed Central

    Fay, Nicolas; Lister, Casey J.; Ellison, T. Mark; Goldin-Meadow, Susan

    2014-01-01

    How does modality affect people's ability to create a communication system from scratch? The present study experimentally tests this question by having pairs of participants communicate a range of pre-specified items (emotions, actions, objects) over a series of trials to a partner using either non-linguistic vocalization, gesture or a combination of the two. Gesture-alone outperformed vocalization-alone, both in terms of successful communication and in terms of the creation of an inventory of sign-meaning mappings shared within a dyad (i.e., sign alignment). Combining vocalization with gesture did not improve performance beyond gesture-alone. In fact, for action items, gesture-alone was a more successful means of communication than the combined modalities. When people do not share a system for communication they can quickly create one, and gesture is the best means of doing so. PMID:24808874

  10. Compositional and micro-scratch analyses of laser induced colored surface of titanium

    NASA Astrophysics Data System (ADS)

    Akman, Erhan; Cerkezoglu, Ecem

    2016-09-01

    Laser marking of metallic surface is a very important application for industry. It is revealed that controlled oxide layer generation above the treated surface leads to colored appearance of metals with interference effect. The oxide layer control is provided with laser and process parameters. In this study, different colors of the Grade 2 titanium samples have been obtained by varying the laser scanning speed. Chromaticity coordinates of the different color surface have been calculated from the reflectance spectrum of the samples. Compositional analyses have been performed using X-ray photoelectron spectroscopy and X-ray diffraction methods. To examine the mechanical properties of the surface, micro-scratch test has been applied to all the colored surfaces. Although delamination has been observed between two laser scanning speed as 950 mm/s and 450 mm/s, it can be said that the adhesion between the titanium substrate and the oxide coating is good.

  11. [A 34-year-old woman with cat scratch disease who developed encephalopathy].

    PubMed

    Yamashita, Hiroyuki; Ubano, Megumi; Uesaka, Yoshikazu; Kunimoto, Masanari

    2012-01-01

    We experienced a patient with cat-scratch disease (CSD) who developed encephalopathy. The subject was a 34-year-old female who had been aware of a low-grade fever and swollen inguinal lymph nodes for 1 month. The subject's consciousness became impaired after a headache developed, accompanied by fever, nausea, and vomiting, and she subsequently sought medical consultation. No major abnormalities were observed in the cerebrospinal fluid and cranial magnetic resonance imaging (MRI) was normal. However, necrotizing lymphadenitis was observed on contrast enhanced computed tomography (CT) of the pelvis and granulomatous changes were observed in a surgical lymph node biopsy. As the subject lived with a pet cat, PCR testing for Bartonella henselae (the CSD pathogen) was performed using a tissue biopsy. This was positive and the subject was diagnosed with CSD encephalopathy. There are very few domestic reports of CSD encephalopathy and care must be taken not to overlook this disease. PMID:22975857

  12. Cat-scratch disease: report of a case with liver lesions and no lymphadenopathy

    SciTech Connect

    Delbeke, D.; Sandler, M.P.; Shaff, M.I.; Miller, S.F.

    1988-08-01

    The usual presentation of cat-scratch disease (CSD) is a subacute regional lymphadenitis following cutaneous inoculation. We present the case of a 10-yr-old white female with a 4-wk history of abdominal pain and fever, without associated lymphadenopathy. A /sup 67/Ga scintigram showed inhomogenous uptake by the liver. An abdominal computed tomographic (CT) scan revealed multiple low density lesions in the liver and the spleen, that were confirmed at laparotomy. Stellate microabscesses were seen on a wedge biopsy of the liver and a CSD antigen skin test was positive. CSD should be considered in the differential diagnosis of liver lesions, even in the absence of lymphadenopathy. This case emphasizes the importance of inhomogeneous /sup 67/Ga uptake by the liver.

  13. Abrasions and lameness in piglets born in different farrowing systems with different types of floor

    PubMed Central

    Zoric, Mate; Nilsson, Ebba; Mattsson, Sigbrit; Lundeheim, Nils; Wallgren, Per

    2008-01-01

    Background The quality of the floor is essential to the welfare of piglets as abrasions often are recorded in newborn piglets, and such lesions may lead to lameness. Apart from animal suffering, lameness contributes to losses in form of dead piglets, decreased growth, and increased use of antibiotics and manual labour. Methods In a herd with three different farrowing systems, 37 litters (390 piglets) were studied until the age of 3 weeks with respect to presence of skin wounds and abrasions. Lameness was registered until the age of 7 weeks. Eight lame piglets were sacrificed before medical treatment and subjected to necropsy including histopathological and microbiological examinations. Isolates of streptococci, staphylococci and E. coli were tested with respect to antimicrobial resistance. Mastitis was observed in ten sows. Results The most severe abrasions at carpus and soles were seen in the system with a new solid concrete floor with a slatted floor over the dunging area. The lowest magnitude was observed in the deep litter system with peat. Sole bruising was more common in the systems with concrete floor compared to the deep litter system with peat, and the differce in prevalence was significant at all examination days. The lesions decreased with time and about 75% of the treatments for lameness were performed during the first three weeks of life. The overall prevalence of lameness was highest in the system with new solid concrete floor with a slatted floor over the dunging area (9.4%) followed by the old solid concrete floor (7.5%). A lower (p < 0.05) prevalence was seen in the deep litters system with peat (3.3%). No significant relationship between mastitis and abrasions or lameness in the offspring was observed. Conclusion There were large differences in the prevalence of abrasions and lameness between the floor types. The deep litter system with peat provided a soft and good floor for piglets. The overall prevalence of lameness was only diagnosed in every

  14. Stability analyses of the mass abrasive projectile high-speed penetrating into concrete target. Part II: Structural stability analyses

    NASA Astrophysics Data System (ADS)

    Wu, Hao; Chen, Xiao-Wei; Fang, Qin; He, Li-Lin

    2014-12-01

    The initial oblique and attacking angles as well as the asymmetrical nose abrasion may lead to bending or even fracture of a projectile, and the penetration efficiency decreases distinctly. The structural stability of a high-speed projectile non-normally penetrating into concrete and the parametric influences involved are analyzed with the mass abrasion taken into account. By considering the symmetrical or asymmetrical nose abrasion as well as the initial oblique and attacking angles, both the axial and the transverse drag forces acting on the projectile are derived. Based on the ideal elastic-plastic yield criterion, an approach is proposed for predicting the limit striking velocity (LSV) that is the highest velocity at which no yielding failure has occurred and the projectile can still maintain its integral structural stability. Furthermore, some particular penetration scenarios are separately discussed in detail. Based on the engineering model for the mass loss and nose-blunting of ogive-nose projectiles established in Part I of this study, the above approach is validated by several high-speed penetration tests. The analysis on parametric influences indicates that the LSV is reduced with an increase in the asymmetrical nose abrasion, the length-diameter-ratio, and the concrete strength, as well as the oblique and attacking angles. Also, the LSV raises with an increase in the initial caliber-radius-head (CRH) and the dimensionless cartridge thickness of a projectile.

  15. A method of generating scratched look calligraphy characters using mathematical morphology

    NASA Astrophysics Data System (ADS)

    Li, Wei; Hagiwara, Ichiro; Yasui, Takao; Chen, Hu-Awei

    2003-10-01

    We propose a method to generate scratched look calligraphy characters by mathematical morphology, and it can decide on the number of times of thinning computation and the structuring element and also can know whether the sizes of generated calligraphy characters are same as the original one in theory. By different changed structuring elements, we can get various scratched look calligraphy characters.

  16. Tribology behavior during indentation and scratch of thin films on substrates: effects of plastic friction

    NASA Astrophysics Data System (ADS)

    Feng, Biao; Chen, Zhitong

    2015-05-01

    When friction stress on a contact surface reaches material yield strength in shear, contact slippage can occur even if the slipping condition for Coulomb friction is not satisfied. In this paper, a three-dimensional (3-D) scratch model is proposed, which considers combined Coulomb and plastic friction. Influences of plastic friction are discussed for two continuous displacement loading steps: indentation and scratch. For indentation, initially the sliding on the contact surface can not take place and the complete cohesion condition should be employed; then as the indenter is further compressed down to the coating surface, plastic friction instead of Coulomb friction prevails in most of the contact region. For scratch, the previous complete cohesion at the initial indentation is substituted by plastic or Coulomb slipping, and the slippage becomes plastic-sliding governed for a slightly large indentation depth. The effects of the indentation depth and the Coulomb friction coefficient on the scratch friction coefficient are discussed in detail. Several experimental phenomena are interpreted, which include that with an increase of the normal loading, the scratch friction coefficient reduces for the soft coating but grows for the hard coating; and with the growth of hardness after heat treatment, the scratch friction coefficient increases due to weak plastic slippage. Obtained results help to elucidate tribological behaviors during scratch and are helpful for the interpretation of experimental phenomena and the improvement of numerical simulations for the scratch process.

  17. Control of surface thermal scratch of strip in tandem cold rolling

    NASA Astrophysics Data System (ADS)

    Chen, Jinshan; Li, Changsheng

    2014-07-01

    The thermal scratch seriously affects the surface quality of the cold rolled stainless steel strip. Some researchers have carried out qualitative and theoretical studies in this field. However, there is currently a lack of research on effective forecast and control of thermal scratch defects in practical production, especially in tandem cold rolling. In order to establish precise mathematical model of oil film thickness in deformation zone, the lubrication in cold rolling process of SUS410L stainless steel strip is studied, and major factors affecting oil film thickness are also analyzed. According to the principle of statistics, mathematical model of critical oil film thickness in deformation zone for thermal scratch is built, with fitting and regression analytical method, and then based on temperature comparison method, the criterion for deciding thermal scratch defects is put forward. Storing and calling data through SQL Server 2010, a software on thermal scratch defects control is developed through Microsoft Visual Studio 2008 by MFC technique for stainless steel in tandem cold rolling, and then it is put into practical production. Statistics indicate that the hit rate of thermal scratch is as high as 92.38%, and the occurrence rate of thermal scratch is decreased by 89.13%. Owing to the application of the software, the rolling speed is increased by approximately 9.3%. The software developed provides an effective solution to the problem of thermal scratch defects in tandem cold rolling, and helps to promote products surface quality of stainless steel strips in practical production.

  18. Effects of Annotations and Homework on Learning Achievement: An Empirical Study of Scratch Programming Pedagogy

    ERIC Educational Resources Information Center

    Su, Addison Y. S.; Huang, Chester S. J.; Yang, Stephen J. H.; Ding, T. J.; Hsieh, Y. Z.

    2015-01-01

    In Taiwan elementary schools, Scratch programming has been taught for more than four years. Previous studies have shown that personal annotations is a useful learning method that improve learning performance. An annotation-based Scratch programming (ASP) system provides for the creation, share, and review of annotations and homework solutions in…

  19. Using Scratch: An Integrated Problem-Solving Approach to Mathematical Thinking

    ERIC Educational Resources Information Center

    Calder, Nigel

    2010-01-01

    "Scratch" is a media-rich digital environment that utilises a building block command structure to manipulate graphic, audio, and video aspects. It incorporates elements of Logo including "tinkerability" in the programming process. In "Scratch" students use geometric and measurement concepts such as coordinates, angle, and length measurements. It…

  20. Fluorescent eye test (image)

    MedlinePlus

    The fluorescent eye test is useful in determining if there is a scratch or other problem with the surface ... has thoroughly covered the eye a cobalt blue light is then directed on the eye. The light ...

  1. Optical-digital detection of dents and scratches on specular metal surfaces.

    PubMed

    Lippincott, H W; Stark, H

    1982-08-15

    An optical-digital approach to the problem of automatic detection of dents and scratches on specular or semispecular surfaces is presented. The method uses the optical reflecting properties of dents and scratches to locate and detect them. Dents are found by a grid projection and encoding technique; scratches are found by using the property that diffuse reflectors scatter over a wider angle (Lambert's law) than specular ones and, therefore, seem brighter when viewed at certain angles. The procedure for finding dents and scratches was found to be very robust: dents as small as 1% of the viewed field and 0.0053 cm (0.0021 in.) deep and scratches as small as 0.003 cm (0.001 in.) wide and 0.00064 cm (0.00025 in.) deep and of variable minimum length were easily detected using nonspecially prepared samples. PMID:20396141

  2. Abrasion cross sections for Ne-20 projectiles at 2.1 GeV/nucleon

    NASA Technical Reports Server (NTRS)

    Townsend, L. W.

    1983-01-01

    Utilizing eikonal scattering theory, an optical model potential approximation to the exact nucleus-nucleus multiple scattering series is used in an abrasion-ablation collision formalism to predict abrasion cross sections for relativistic Ne-20 projectile nuclei. Excellent agreement with recent experimental abrasion results is obtained. The sensitivity of the abrasion predictions to Pauli exclusion principle correlation effects and to the assumed shape of the nuclear single-particle density distribution is also demonstrated.

  3. Hydro- abrasive jet machining modeling for computer control and optimization

    NASA Astrophysics Data System (ADS)

    Groppetti, R.; Jovane, F.

    1993-06-01

    Use of hydro-abrasive jet machining (HAJM) for machining a wide variety of materials—metals, poly-mers, ceramics, fiber-reinforced composites, metal-matrix composites, and bonded or hybridized mate-rials—primarily for two- and three-dimensional cutting and also for drilling, turning, milling, and deburring, has been reported. However, the potential of this innovative process has not been explored fully. This article discusses process control, integration, and optimization of HAJM to establish a plat-form for the implementation of real-time adaptive control constraint (ACC), adaptive control optimiza-tion (ACO), and CAD/CAM integration. It presents the approach followed and the main results obtained during the development, implementation, automation, and integration of a HAJM cell and its computer-ized controller. After a critical analysis of the process variables and models reported in the literature to identify process variables and to define a process model suitable for HAJM real-time control and optimi-zation, to correlate process variables and parameters with machining results, and to avoid expensive and time-consuming experiments for determination of the optimal machining conditions, a process predic-tion and optimization model was identified and implemented. Then, the configuration of the HAJM cell, architecture, and multiprogramming operation of the controller in terms of monitoring, control, process result prediction, and process condition optimization were analyzed. This prediction and optimization model for selection of optimal machining conditions using multi-objective programming was analyzed. Based on the definition of an economy function and a productivity function, with suitable constraints relevant to required machining quality, required kerfing depth, and available resources, the model was applied to test cases based on experimental results.

  4. The Corynebacterium glutamicum aconitase repressor: scratching around for crystals

    PubMed Central

    García-Nafría, Javier; Baumgart, Meike; Bott, Michael; Wilkinson, Anthony J.; Wilson, Keith S.

    2010-01-01

    Imperfections on the surfaces of crystallization containers are known to influence crystal formation and are thought to do so by helping to overcome the nucleation barrier. The intentional creation of imperfections has been widely applied to induce crystallization of small molecules, but has not been reported for protein crystallization. Here, the crystallization and preliminary X-ray analysis of the TetR-type aconitase repressor are reported. This regulator was the first transcription factor to be identified in the regulation of the tricarboxylic acid cycle in Corynebacterium glutamicum, an organism that is of special industrial interest and is an emerging model organism for Corynebacterineae. Successful crystallization involved introducing manual scratches on the surface of standard commercial plates, which led to a substantial improvement in crystal nucleation and quality. PMID:20823530

  5. Optically transparent, scratch-resistant, diamond-like carbon coatings

    DOEpatents

    He, Xiao-Ming; Lee, Deok-Hyung; Nastasi, Michael A.; Walter, Kevin C.; Tuszewski, Michel G.

    2003-06-03

    A plasma-based method for the deposition of diamond-like carbon (DLC) coatings is described. The process uses a radio-frequency inductively coupled discharge to generate a plasma at relatively low gas pressures. The deposition process is environmentally friendly and scaleable to large areas, and components that have geometrically complicated surfaces can be processed. The method has been used to deposit adherent 100-400 nm thick DLC coatings on metals, glass, and polymers. These coatings are between three and four times harder than steel and are therefore scratch resistant, and transparent to visible light. Boron and silicon doping of the DLC coatings have produced coatings having improved optical properties and lower coating stress levels, but with slightly lower hardness.

  6. 29 CFR 1910.215 - Abrasive wheel machinery.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... wheel in motion. (5) Excluded machinery. Natural sandstone wheels and metal, wooden, cloth, or paper... apply to natural sandstone wheels or metal, wooden, cloth, or paper discs, having a layer of abrasive on... and Type 27A cutting-off wheels. (g) Certain internal wheels. (h) Type 4 tapered wheels. (i)...

  7. 29 CFR 1910.215 - Abrasive wheel machinery.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... wheel in motion. (5) Excluded machinery. Natural sandstone wheels and metal, wooden, cloth, or paper... apply to natural sandstone wheels or metal, wooden, cloth, or paper discs, having a layer of abrasive on... and Type 27A cutting-off wheels. (g) Certain internal wheels. (h) Type 4 tapered wheels. (i)...

  8. 29 CFR 1926.303 - Abrasive wheels and tools.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... spindle speed at safe levels under all conditions of normal operation. (b) Guarding. (1) Grinding machines.... (1) Floor stand and bench mounted abrasive wheels, used for external grinding, shall be provided with safety guards (protection hoods). The maximum angular exposure of the grinding wheel periphery and...

  9. Potential of Air-Propelled Abrasives for Selective Weed Control

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Novel forms of selective weed control are needed by many types of growers, but especially organic growers who are restricted from using synthetic herbicides. Abrasive grit made from corn cobs was expelled from a sand blaster at 517 kPa pressure and aimed at seedlings of common lambsquarters and corn...

  10. Abrasive blasting agents: designing studies to evaluate relative risk.

    PubMed

    Hubbs, Ann; Greskevitch, Mark; Kuempel, Eileen; Suarez, Fernando; Toraason, Mark

    Workers exposed to respirable crystalline silica used in abrasive blasting are at increased risk of developing a debilitating and often fatal fibrotic lung disease called silicosis. The National Institute for Occupational Safety and Health (NIOSH) recommends that silica sand be prohibited as abrasive blasting material and that less hazardous materials be used in blasting operations. However, data are needed on the relative risks associated with exposure to abrasive blasting materials other than silica. NIOSH has completed acute studies in rats (Hubbs et al., 2001; Porter et al., 2002). To provide dose-response data applicable to making recommendation for occupational exposure limits, NIOSH has collaborated with the National Toxicology Program (NTP) to design longer term studies with silica substitutes. For risk assessment purposes, selected doses will include concentrations that are relevant to human exposures. Rat lung burdens achieved should be comparable to those estimated in humans with working lifetime exposures, even if this results in "overloading" doses in rats. To quantify both dose and response, retained particle burdens in the lungs and lung-associated lymph nodes will be measured, as well as biochemical and pathological indices of pulmonary response. This design will facilitate assessment of the pulmonary fibrogenic potential of inhaled abrasive blasting agents at occupationally relevant concentrations. PMID:16020188

  11. Peel strength of denture liner to PMMA and polyamide: laser versus air-abrasion

    PubMed Central

    Bagis, Bora; Özcan, Mutlu; Durkan, Rukiye; Turgut, Sedanur; Ates, Sabit Melih

    2013-01-01

    PURPOSE This study investigated the effect of laser parameters and air-abrasion on the peel strength of silicon-based soft denture liner to different denture resins. MATERIALS AND METHODS Specimens (N=180) were prepared out of three different denture base resins (Rodex, cross-linked denture base acrylic resin; Paladent, heat-cured acrylic resin; Deflex, Polyamide resin) (75 mm × 25 mm × 3 mm). A silicon-based soft denture liner (Molloplast B) was applied to the denture resins after the following conditioning methods: a) Air-abrasion (50 µm), b) Er,Cr:YSGG laser (Waterlase MD Turbo, Biolase Technology) at 2 W-20 Hz, c) Er,Cr:YSGG laser at 2 W-30 Hz, d) Er,Cr:YSGG laser at 3 W-20 Hz, e) Er,Cr:YSGG laser at 3 W-30 Hz. Non-conditioned group acted as the control group. Peel test was performed in a universal testing machine. Failure modes were evaluated visually. Data were analyzed using two-way ANOVA and Tukey's test (α=.05). RESULTS Denture liner tested showed increased peel strength after laser treatment with different parameters (3.9±0.4 - 5.58±0.6 MPa) compared to the control (3.64±0.5 - 4.58±0.5 MPa) and air-abraded groups (3.1±0.6 - 4.46±0.3 MPa), but the results were not statistically significant except for Paladent, with the pretreatment of Er,Cr:YSGG laser at 3 W-20 Hz. Polyamide resin after air-abrasion showed significantly lower peel strength than those of other groups (3.1±0.6 MPa). CONCLUSION Heat-cured acrylic resin, PMMA, may benefit from Er,Cr:YSGG laser treatment at 3 W-20 Hz irradiation. Air-abrasion of polyamide resins should be avoided not to impair their peel bond strengths to silicon-based soft denture liners. PMID:24049570

  12. Do soil microbes and abrasion by soil particles influence persistence and loss of physical dormancy in seeds of tropical pioneers?

    PubMed Central

    Zalamea, Paul-Camilo; Sarmiento, Carolina; Arnold, A. Elizabeth; Davis, Adam S.; Dalling, James W.

    2015-01-01

    Germination from the soil seed bank (SSB) is an important determinant of species composition in tropical forest gaps, with seed persistence in the SSB allowing trees to recruit even decades after dispersal. The capacity to form a persistent SSB is often associated with physical dormancy, where seed coats are impermeable at the time of dispersal. Germination literature often speculates, without empirical evidence, that dormancy-break in physically dormant seeds is the result of microbial action and/or abrasion by soil particles. We tested the microbial/soil abrasion hypothesis in four widely distributed neotropical pioneer tree species (Apeiba membranacea, Luehea seemannii, Ochroma pyramidale, and Cochlospermum vitifolium). Seeds were buried in five common gardens in a lowland tropical forest in Panama, and recovered at 1, 3, 6, and 12 months after burial. Seed permeability, microbial infection, seed coat thickness, and germination were measured. Parallel experiments compared the germination fraction of fresh and aged seeds without soil contact, and in seeds as a function of seed permeability. Contrary to the microbial/soil abrasion hypothesis the proportion of permeable seeds, and of seeds infected by cultivable microbes, decreased as a function of burial duration. Furthermore, seeds stored in dark and dry conditions for 2 years showed a higher proportion of seed germination than fresh seeds in identical germination conditions. We determined that permeable seeds of A. membranacea and O. pyramidale had cracks in the chalazal area or lacked the chalazal plug, whereas all surfaces of impermeable seeds were intact. Our results are inconsistent with the microbial/soil abrasion hypothesis of dormancy loss and instead suggest the existence of multiple dormancy phenotypes, where a fraction of each seed cohort is dispersed in a permeable state and germinates immediately, while the impermeable seed fraction accounts for the persistent SSB. Thus, we conclude that fluctuations

  13. Do soil microbes and abrasion by soil particles influence persistence and loss of physical dormancy in seeds of tropical pioneers?

    PubMed

    Zalamea, Paul-Camilo; Sarmiento, Carolina; Arnold, A Elizabeth; Davis, Adam S; Dalling, James W

    2014-01-01

    Germination from the soil seed bank (SSB) is an important determinant of species composition in tropical forest gaps, with seed persistence in the SSB allowing trees to recruit even decades after dispersal. The capacity to form a persistent SSB is often associated with physical dormancy, where seed coats are impermeable at the time of dispersal. Germination literature often speculates, without empirical evidence, that dormancy-break in physically dormant seeds is the result of microbial action and/or abrasion by soil particles. We tested the microbial/soil abrasion hypothesis in four widely distributed neotropical pioneer tree species (Apeiba membranacea, Luehea seemannii, Ochroma pyramidale, and Cochlospermum vitifolium). Seeds were buried in five common gardens in a lowland tropical forest in Panama, and recovered at 1, 3, 6, and 12 months after burial. Seed permeability, microbial infection, seed coat thickness, and germination were measured. Parallel experiments compared the germination fraction of fresh and aged seeds without soil contact, and in seeds as a function of seed permeability. Contrary to the microbial/soil abrasion hypothesis the proportion of permeable seeds, and of seeds infected by cultivable microbes, decreased as a function of burial duration. Furthermore, seeds stored in dark and dry conditions for 2 years showed a higher proportion of seed germination than fresh seeds in identical germination conditions. We determined that permeable seeds of A. membranacea and O. pyramidale had cracks in the chalazal area or lacked the chalazal plug, whereas all surfaces of impermeable seeds were intact. Our results are inconsistent with the microbial/soil abrasion hypothesis of dormancy loss and instead suggest the existence of multiple dormancy phenotypes, where a fraction of each seed cohort is dispersed in a permeable state and germinates immediately, while the impermeable seed fraction accounts for the persistent SSB. Thus, we conclude that fluctuations

  14. Structural and chemical characteristics of atomically smooth GaN surfaces prepared by abrasive-free polishing with Pt catalyst

    NASA Astrophysics Data System (ADS)

    Murata, Junji; Sadakuni, Shun; Okamoto, Takeshi; Hattori, Azusa N.; Yagi, Keita; Sano, Yasuhisa; Arima, Kenta; Yamauchi, Kazuto

    2012-06-01

    This paper reports the structural and chemical characteristics of atomically flat gallium nitride (GaN) surfaces prepared by abrasive-free polishing with platinum (Pt) catalyst. Atomic force microscopy revealed regularly alternating wide and narrow terraces with a step height equivalent to that of a single bilayer on the flattened GaN surfaces, which originate from the differences in etching rate of two neighboring terraces. The material removal characteristics of the method for GaN surfaces were investigated in detail. We confirmed that an atomically smooth GaN surface with an extremely small number of surface defects, including pits and scratches, can be achieved, regardless of the growth method, surface polarity, and doping concentration. X-ray photoelectron spectroscopy showed that the flattening method produces clean GaN surfaces with only trace impurities such as Ga oxide and metallic Ga. Contamination with the Pt catalyst was also evaluated using total-reflection X-ray fluorescence analysis. A wet cleaning method with aqua regia is proposed, which markedly eliminates this Pt contamination without affecting the surface morphology.

  15. Inhibitory effect of lidocaine on pain and itch using formalin-induced nociception and 5′-guanidinonaltrindole-induced scratching models in mice: behavioral and neuroanatomical evidence

    PubMed Central

    Inan, Saadet; Dun, Nae J.; Cowan, Alan

    2009-01-01

    The aim of this study was to establish the effect of lidocaine, a local anesthetic, on pain and itch using formalin-induced nociception and kappa opioid antagonist-induced scratching models in mice. We investigated if local intradermal pretreatment (at −10 min) with lidocaine N-ethyl bromide (lidocaine, 2%, 0.1 ml) antagonizes behavioral responses and prevents c-fos expression induced by pain and itch. Male, Swiss Webster mice (25–30 g, n=6–10) were used. Formalin (5%, 20 µl, s.c.) or saline was administered to the right dorsal hindpaw and the time spent licking this paw was recorded at 0–10 min and 20–35 min. For itching, mice were challenged with 5′- guanidinonaltrindole (GNTI, 0.3 mg/kg, s.c., behind the neck) or saline and the number of neck-directed scratches with hindpaws was counted for 30 min. C-fos immunohistochemistry was performed in lumbar (for pain) and cervical (for scratching) spinal sections 2 h after respective treatments. We found that lidocaine (a) antagonizes both formalin-induced pain and GNTI-induced scratching and (b) prevents c-fos expression evoked by pain (medial side of the superficial layer and deeper layers of the dorsal horn) and itch (lateral side of the superficial layer of the dorsal horn). Additionally, GNTI caused c-fos activation in mice wearing an Elizabethan collar (to prevent scratching of the neck) suggesting that GNTI provokes c-fos expression by inducing an itch sensation. Our results highlight the antipruritic properties of lidocaine and argue for its comprehensive clinical testing against pruritic states. PMID:19549515

  16. Chloroquine-induced scratching is mediated by NO/cGMP pathway in mice.

    PubMed

    Foroutan, Arash; Haddadi, Nazgol Sadat; Ostadhadi, Sattar; Sistany, Narges; Dehpour, Ahmad Reza

    2015-07-01

    Chloroquine (CQ), a 4-aminoquinoline drug, has long been used in the treatment and prevention of malaria. However its side effect generalized pruritus contributes to treatment failures, and consequently results in the development of chloroquine resistant strains of Plasmodium falciparum. It was proposed that the administration of CQ correlated with increase in nitric oxide (NO) production. Nitric oxide is involved in some pruritic disorders such as atopic dermatitis, psoriasis and scratching behavior evoked by pruritogens like substance P. Therefore, the aim of this study was to investigate the involvement of NO/cGMP pathway in CQ-induced scratching in mice. Scratching behaviors were recorded by a camera after intradermal (ID) injection of CQ in the shaved rostral back of the mice. The results obtained show that CQ elicited scratching in a dose-dependent manner with a peak effective dose of 400μg/site. Injection of non-specific NOS inhibitor, N-nitro-l-arginine methyl ester or neuronal NOS selective inhibitor and 7-nitroindazole, reduced CQ-induced scratching significantly. On the other hand, administration of aminoguanidine as inducible NOS inhibitor has no inhibitory effect on this behavior. Also, injection of l-arginine as a precursor of NO significantly increased this response. Conversely, accumulation of cGMP by sildenafil as a selective phosphodiesterase type 5 inhibitor, potentiated the scratching behavior by CQ. This study therefore shows that CQ-induced scratching behavior is mediated by the NO/cGMP pathway. PMID:25957523

  17. Zyklophin, a short-acting kappa opioid antagonist, induces scratching in mice

    PubMed Central

    DiMattio, K.M.; Yakovleva, T.V.; Aldrich, J.V.; Cowan, A.; Liu-Chen, L.Y.

    2014-01-01

    It has been shown previously that norbinaltorphimine (norBNI) and 5΄-guanidinonaltrindole (5΄-GNTI), long-acting kappa opioid receptor (KOPR) antagonists, cause frenzied scratching in mice [1;2]. In the current study, we examined if zyklophin, a short-acting cyclic peptide KOPR antagonist, also elicited scratching behavior. When injected s.c. in the nape of the neck of male Swiss-Webster mice, zyklophin at doses of 0.1, 0.3 and 1 mg/kg induced dose-related hindleg scratching of the neck between 3 and 15 min after injection. Pretreating mice with norBNI (20 mg/kg, i.p.) at 18–20 hr before challenge with zyklophin (0.3 mg/kg) did not markedly affect scratching. Additionally, KOPR −/− mice given 0.3 mg/kg of zyklophin displayed similar levels of scratching as wild-type animals. The absence of KOPR in KOPR −/− mice was confirmed with ex vivo radioligand binding using [3H]U69,593. Taken together, our data suggest that the presence of kappa receptors is not required for the excessive scratching caused by zyklophin. Thus, zyklophin, similar to the structurally different KOPR antagonist 5΄-GNTI, appears to act at other targets to elicit scratching and potentially the sensation of itch. PMID:24503508

  18. Effect of 2,3,7,8-tetrachlorodibenzo-p-dioxin on scratching behavior in mice.

    PubMed

    Ono, Rie; Kagawa, Yoto; Takahashi, Yuji; Akagi, Masaki; Kamei, Chiaki

    2010-03-01

    The present study was performed to study the effect of 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) on scratching behavior in hairless mice, which are highly sensitive to pruritogens (mediators causing itching), except for histamine, and are suitable for time-course studies due to their hairless skin. TCDD is a well-known environmental pollutant that causes skin diseases with itching; therefore, we examined whether TCDD induced itching. Oral administration of TCDD caused no increase in scratching behavior when used alone, whereas TCDD in combination with distilled water or acetone/olive oil application caused a significant increase in scratching behavior. Furthermore, nerve growth factor (NGF) content in the skin increased significantly. A single administration of chlorpheniramine (histamine H1 receptor antagonist), tranilast (chemical mediator release inhibitor) and olopatadine (histamine H1 receptor antagonist) had no effect on scratching behavior induced by TCDD in combination with acetone/olive oil application. With repeated administration for 7 days, chlorpheniramine and tranilast had no effect on scratching behavior, whereas olopatadine significantly inhibited scratching behavior. In addition, only olopatadine significantly inhibited NGF content in the skin. From these findings, it can be concluded that TCDD is not a pruritogen but causes alloknesis (itchy skin) with the simultaneous use of trivial external stimulation. In addition, it was found that drugs which decreased skin NGF contents may inhibit this scratching behavior. PMID:19969104

  19. Degradation of nontoxic fouling-release coatings as a result of abrasion and long-term exposure

    SciTech Connect

    Meyer, A.E.; Baier, R.E.; Forsberg, R.L.

    1995-06-01

    Previous work by this research group demonstrates that methylsilicone-based coatings having critical surface tensions between 20 and 25 mN/m allow easy mechanical detachment of zebra mussel infestations and other fouling for at least 2 years. Continuing evaluations of the coated test panels and trash racks at test sites in western New York confirm and extend the 2-year findings. Coatings which, in addition, contain elutable oils display an apparent further resistance to initial colonization by zebra mussels, but this early benefit does not carry over to the brush-removal forces required for cleaning of the once-fouled coating. Several of the elastomeric methylsilicone coatings are prone to cutting and abrasion damage, limiting their suitability for heavy-duty use and/or situations requiring periodic cleaning. Since standard tests for abrasion and wear developed for paints are not applicable to elastomeric coatings, our laboratory is using a brush abrasion test to evaluate fouling-release coatings for an increasing series of wet brushing cycles.

  20. Solid Lubrication Fundamentals and Applications. Chapter 5; Abrasion: Plowing and Cutting

    NASA Technical Reports Server (NTRS)

    Miyoshi, Kazuhisa

    2001-01-01

    Chapter 5 discusses abrasion, a common wear phenomenon of great economic importance. It has been estimated that 50% of the wear encountered in industry is due to abrasion. Also, it is the mechanism involved in the finishing of many surfaces. Experiments are described to help in understanding the complex abrasion process and in predicting friction and wear behavior in plowing and/or cutting. These experimental modelings and measurements used a single spherical pin (asperity) and a single wedge pin (asperity). Other two-body and three-body abrasion studies used hard abrasive particles.

  1. Microstructures and Abrasive Properties of the Oxide Coatings on Al6061 Alloys Prepared by Plasma Electrolytic Oxidation in Different Electrolytes

    NASA Astrophysics Data System (ADS)

    Wang, Kai; Byun, Sangsik; Lee, Chan Gyu; Koo, Bon Heun; Wang, Yi Qi; Song, Jung Il

    Al2O3 coatings were prepared on T6-tempered Al6061 alloys substrate under a hybrid voltage (AC 200 V-60 Hz and DC 260 V value) by plasma electrolytic oxidation (PEO) in 30 min. The effects of different electrolytes on the abrasive behaviors of the coatings were studied by conducting dry ball-on-disk wear tests. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to investigate the coating microstructure. XRD analysis results show that the coatings mainly consist of α- and γ-Al2O3, and some mullite and AlPO4 phase in Na2SiO3 and Na3PO4 containing electrolytes, respectively. The wear test results show that the coatings which were PEO-treated in Na3PO4 containing electrolyte presented the most excellent abrasive resistance property.

  2. Protective, Abrasion-Resistant Coatings With Tailorable Properties

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Because of their light weight and impact resistance, transparent plastic structures are becoming increasingly desirable for use not only on aircraft but also in terrestrial applications such as automotive windshields and ophthalmic lenses. However, plastics are typically soft and scratch readily, reducing their transparency with use. At the NASA Lewis Research Center, reactively deposited aluminum oxide coatings as thin as 12,000 angstroms have been demonstrated to provide improved resistance to most scratches encountered during normal use. The properties of the coating can be adjusted to tailor the surface to meet other needs, such as water shedding. These adjustments can be made during the deposition process so that multiple manufacturing steps are eliminated.

  3. Abrasive Wear Study of NiCrFeSiB Flame Sprayed Coating

    NASA Astrophysics Data System (ADS)

    Sharma, Satpal

    2013-10-01

    In the present study, abrasive wear behavior of NiCrFeSiB alloy coating on carbon steel was investigated. The NiCrFeSiB coating powder was deposited by flame spraying process. The microstructure, porosity and hardness of the coatings were evaluated. Elemental mapping was carried out in order to study the distribution of various elements in the coating. The abrasive wear behavior of these coatings was investigated under three normal loads (5, 10 and 15 N) and two abrasive grit sizes (120 and 320 grit). The abrasive wear rate was found to increase with the increase of load and abrasive size. The abrasive wear resistance of coating was found to be 2-3 times as compared to the substrate. Analysis of the scanning electron microscope images revealed cutting and plowing as the material removal mechanisms in these coatings under abrasive wear conditions used in this investigation.

  4. Scratched-XY Universality and Phase Diagram of Disordered 1D Bosons in Optical Lattice

    NASA Astrophysics Data System (ADS)

    Yao, Zhiyuan; Pollet, Lode; Prokof'ev, Nikolay; Svistunov, Boris

    The superfluid-insulator quantum phase transition in a 1D system with weak links belongs to the so-called scratched-XY universality class, provided the irrenormalizable exponent ζ characterizing the distribution of weak links is smaller than 2 / 3 . With a combination of worm-algorithm Monte Carlo simulations and asymptotically exact analytics, we accurately trace the position of the scratched-XY critical line on the ground-state phase diagram of bosonic Hubbard model at unity filling. In particular, we reveal the location of the tricritical point separating the scratched-XY criticality from the Giamarchi-Schulz one.

  5. Microleakage on Class V glass ionomer restorations after cavity preparation with aluminum oxide air abrasion.

    PubMed

    Corona, Silmara Aparecida Milori; Borsatto, Maria Cristina; Rocha, Renata Andréa Salvitti de Sá; Palma-Dibb, Regina Guenka

    2005-01-01

    This in vitro study assessed the marginal microleakage on class V cavities prepared with aluminum oxide air abrasion and restored with different glass ionomer cements. The cavities were prepared on the buccal and lingual surfaces of 15 sound third molars with an air- abrasion device (Kreativ Mach 4.1; New Image) using a 27.5-microm aluminum oxide particle stream, and were assigned to 3 groups of 10 cavities each. The restorative materials were: group I, a conventional glass ionomer cement (Ketac-Fil); groups II and III, resin-modified glass ionomer cements (Vitremer R and Fuji II LC, respectively). After placement of the restorations, the teeth were stored in distilled water at 37 degrees C for 24 h, polished and then submitted to a thermocycling regimen of 500 cycles, isolated, immersed in 0.2% Rhodamine B solution for 24 h, included and serially sectioned. Microleakage was assessed by viewing the specimens under an optical microscope connected to a color video camera and a computer. The images obtained were digitized and analyzed for microleakage using software that allows for a standard quantitative assessment of dye penetration in millimeters. Statistical analysis was done using the Kruskall-Wallis and Wilcoxon tests. Means of dye penetration (%) were: occlusal - I: 25.76 +/- 34.35, II: 20.00 +/- 42.16, III: 28.25 +/- 41.67; cervical - I: 23.72 +/- 41.84; II: 44.22 +/- 49.69, III: 39.27 +/- 50.74. No statistically significant differences (p>0.05) were observed among either the glass ionomer cements or the margins. In conclusion, class V cavities restored with either conventional or resin-modified glass ionomer cements after preparation with aluminum oxide air abrasion did not show complete sealing at the enamel and dentin/cementum margins. PMID:16113931

  6. Advance Abrasion Resistant Materials for Mining

    SciTech Connect

    Mackiewicz-Ludtka, G.

    2004-06-01

    The high-density infrared (HDI) transient-liquid coating (TLC) process was successfully developed and demonstrated excellent, enhanced (5 times higher than the current material and process) wear performance for the selected functionally graded material (FGM) coatings under laboratory simulated, in-service conditions. The mating steel component exhibited a wear rate improvement of approximately one and a half (1.5) times. After 8000 cycles of. wear testing, the full-scale component testing demonstrated that the coating integrity was still excellent. Little or no spalling was observed to occur.

  7. ADVANCED ABRASION RESISTANT MATERIALS FOR MINING

    SciTech Connect

    Ludtka, G.M.

    2004-04-08

    The high-density infrared (HDI) transient-liquid coating (TLC) process was successfully developed and demonstrated excellent, enhanced (5 times higher than the current material and process) wear performance for the selected functionally graded material (FGM) coatings under laboratory simulated, in-service conditions. The mating steel component exhibited a wear rate improvement of approximately one and a half (1.5) times. After 8000 cycles of wear testing, the full-scale component testing demonstrated that the coating integrity was still excellent. Little or no spalling was observed to occur.

  8. Surface deformation and friction characteristic of nano scratch at ductile-removal regime for optical glass BK7.

    PubMed

    Li, Chen; Zhang, Feihu; Ding, Ye; Liu, Lifei

    2016-08-20

    Nano scratch for optical glass BK7 based on the ductile-removal regime was carried out, and the influence rule of scratch parameters on surface deformation and friction characteristic was analyzed. Experimental results showed that, with increase of normal force, the deformation of burrs in the edge of the scratch was more obvious, and with increase of the scratch velocity, the deformation of micro-fracture and burrs in the edge of the scratch was more obvious similarly. The residual depth of the scratch was measured by atomic force microscope. The experimental results also showed that, with increase of normal force, the residual depth of the scratch increased linearly while the elastic recovery rate decreased. Furthermore, with increase of scratch velocity, the residual depth of the scratch decreased while the elastic recovery rate increased. The scratch process of the Berkovich indenter was divided into the cutting process of many large negative rake faces based on the improved cutting model, and the friction characteristic of the Berkovich indenter and the workpiece was analyzed. The analysis showed that the coefficient of friction increased and then tended to be stable with the increase of normal force. Meanwhile, the coefficient of friction decreased with the increase of scratch velocity, and the coefficients, k ln(v) and μ0, were introduced to improve the original formula of friction coefficient. PMID:27556970

  9. The interaction between histamine H1 receptor and μ- opioid receptor in scratching behavior in ICR mice.

    PubMed

    Nakasone, Tasuku; Sugimoto, Yumi; Kamei, Chiaki

    2016-04-15

    In this study, we examined the interaction between histamine H1 receptor and μ-opioid receptor in scratching behavior in ICR mice. Both histamine and morphine caused scratching and simultaneous injection of histamine and morphine had an additive effect. Chlorpheniramine and naloxone inhibited histamine-induced scratching behavior. These two drugs also inhibited morphine-induced scratching behavior. Simultaneous injection of chlorpheniramine and naloxone caused a significant inhibition of histamine-induced scratching compared with separate injections. The same findings were also noted for morphine-induced scratching. These results strongly indicate a close relationship between histamine H1 receptor and μ-opioid receptor in scratching behavior in ICR mice. PMID:26948312

  10. Nanometric Finishing on Biomedical Implants by Abrasive Flow Finishing

    NASA Astrophysics Data System (ADS)

    Subramanian, Kavithaa Thirumalai; Balashanmugam, Natchimuthu; Shashi Kumar, Panaghra Veeraiah

    2016-01-01

    Abrasive flow finishing (AFF) is a non-conventional finishing technique that offers better accuracy, efficiency, consistency, economy in finishing of complex/difficult to machine materials/components and provides the possibility of effective automation as aspired by the manufacturing sector. The present study describes the finishing of a hip joint made of ASTM grade Co-Cr alloy by Abrasive Flow Machining (AFM) process. The major input parameters of the AFF process were optimized for achieving nanometric finishing of the component. The roughness average (Ra) values were recorded during experimentation using surface roughness tester and the results are discussed in detail. The surface finished hip joints were characterized using Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and residual stress analysis using X-Ray Diffraction (XRD). The discussion lays emphasis on the significance, efficacy and versatile nature of the AFF process in finishing of bio-medical implants.

  11. Microstructure and abrasive wear in silicon nitride ceramics

    SciTech Connect

    Dogan, Cynthia P.; Hawk, Jeffrey A.

    2001-10-01

    It is well known that abrasive wear resistance is not strictly a materials property, but also depends upon the specific conditions of the wear environment. Nonetheless, characteristics of the ceramic microstructure do influence its hardness and fracture toughness and must, therefore, play an active role in determining howa ceramic will respond to the specific stress states imposed upon it by the wear environment. In this study, the ways in which composition and microstructure influence the abrasive wear behavior of six commercially-produced silicon nitride based ceramics are examined. Results indicate that microstructural parameters, such as matrix grain size and orientation, porosity, and grain boundary microstructure, and thermal expansion mismatch stresses created as the result of second phase formation, influence the wear rate through their effect on wear sheet formation and subsurface fracture. It is also noted that the potential impact of these variables on the wear rate may not be reflected in conventional fracture toughness measurements.

  12. Self inflicted corneal abrasions due to delusional parasitosis

    PubMed Central

    Meraj, Adeel; Din, Amad U; Larsen, Lynn; Liskow, Barry I

    2011-01-01

    The authors report a case of self inflicted bilateral corneal abrasions and skin damage due to ophthalmic and cutaneous delusional parasitosis. A male in his 50s presented with a 10 year history of believing that parasites were colonizing his skin and biting into his skin and eyes. The patient had received extensive medical evaluations that found no evidence that symptoms were due to a medical cause. He was persistent in his belief and had induced bilateral corneal abrasions and skin damage by using heat lamps and hair dryers in an attempt to disinfect his body. The patient was treated with olanzapine along with treatment for his skin and eyes. His delusional belief system persisted but no further damage to his eyes and skin was noted on initial follow-up. PMID:22689836

  13. Wear and abrasion resistance selection maps of biological materials.

    PubMed

    Amini, Shahrouz; Miserez, Ali

    2013-08-01

    The mechanical design of biological materials has generated widespread interest in recent years, providing many insights into their intriguing structure-property relationships. A critical characteristic of load-bearing materials, which is central to the survival of many species, is their wear and abrasion tolerance. In order to be fully functional, protective armors, dentitious structures and dynamic appendages must be able to tolerate repetitive contact loads without significant loss of materials or internal damage. However, very little is known about this tribological performance. Using a contact mechanics framework, we have constructed materials selection charts that provide general predictions about the wear performance of biological materials as a function of their fundamental mechanical properties. One key assumption in constructing these selection charts is that abrasion tolerance is governed by the first irreversible damage at the contact point. The maps were generated using comprehensive data from the literature and encompass a wide range of materials, from heavily mineralized to fully organic materials. Our analysis shows that the tolerance of biological materials against abrasion depends on contact geometry, which is ultimately correlated to environmental and selective pressures. Comparisons with experimental data from nanoindentation experiments are also drawn in order to verify our predictions. With the increasing amount of data available for biological materials also comes the challenge of selecting relevant model systems for bioinspired materials engineering. We suggest that these maps will be able to guide this selection by providing an overview of biological materials that are predicted to exhibit the best abrasion tolerance, which is of fundamental interest for a wide range of applications, for instance in restorative implants and protective devices. PMID:23643608

  14. Mass flow rate measurement in abrasive jets using acoustic emission

    NASA Astrophysics Data System (ADS)

    Ivantsiv, V.; Spelt, J. K.; Papini, M.

    2009-09-01

    The repeatability of abrasive jet machining operations is presently limited by fluctuations in the mass flow rate due to powder compaction, stratification and humidity effects. It was found that the abrasive mass flow rate for a typical abrasive jet micromachining setup could be determined by using data from the acoustic emission of the abrasive jet impacting a flat plate. Two methods for extracting the mass flow rate from the acoustic emission were developed and compared. In the first method, the number of particle impacts per unit time was determined by a direct count of peaks in the acoustic emission signal. The second method utilizes the power spectrum density of the acoustic emission in a specific frequency range. Both measures were found to correlate strongly with the mass flow rate measured by weighing samples of blasted powder for controlled time periods. It was found that the peak count method permits measurement of the average frequency of the impacts and the mass flow rate, but can only be applied to flow rates in which the impact frequency is approximately one order of magnitude less than the frequency of the target plate ringing. The power spectrum density method of signal processing is applicable to relatively fine powders and to flow rates at which the average impact frequency is of the same order of magnitude as that of the ringing due to the impact. The acoustic emission technique can be used to monitor particle flow variations over a wide range of time periods and provides a straightforward and accurate means of process control.

  15. Lithologic Influence and Experimental Variability in Gravel Abrasion: Implications for Predicting Rates of Downstream Fining of River Bed Sediments

    NASA Astrophysics Data System (ADS)

    Farrow, J. W.; Sklar, L. S.

    2004-12-01

    The question of what controls the occurrence and rate of downstream fining of bed-material sediments remains a fundamental unsolved problem despite over a century of field, experimental and theoretical investigations. Downstream fining rates are commonly modeled as exponential or power-law functions of travel distance. Much recent work has focused on the relative influence of particle abrasion and differential transport, however, no general method has been developed for explicitly accounting for the influence of rock strength in parameterizing fining models. Here we report preliminary results of laboratory tumbling experiments in which we are investigating the influence of variable rock durability, both between and within distinct lithologic units, on rates of particle abrasion. We consider three separate questions: 1) can rock tensile strength be used to predict differences in bulk fining rates across a wide spectrum of rock types; 2) does variability in rock durability among individual gravel clasts of the same lithologic composition and initial grain size lead to patterns of downstream evolution of grain size distributions that differ significantly from the predictions of simple fining models; and 3) how large is the uncertainty in abrasion coefficients determined by laboratory tumbling, as determined by replicate experiments with identical initial conditions? We use a horizontal axis, 25-cm diameter, steel barrel tumbler, driven by a mechanical transmission with excellent control of rotational velocity. Rock samples were collected from units of the Franciscan Formation in the Redwood Creek Watershed of Marin County, California, and from sedimentary and intrusive volcanic rocks of the Henry Mountains, in southeastern Utah. We collected clasts predominantly from hillslope source areas, to focus our attention on the durability of gravel as it enters the river network. We use the `Brazilian' tensile splitting test to measure the strength of 50-mm diameter core

  16. Abrasion of Candidate Spacesuit Fabrics by Simulated Lunar Dust

    NASA Technical Reports Server (NTRS)

    Gaier, James R.; Meador, Mary Ann; Rogers, Kerry J.; Sheehy, Brennan H.

    2009-01-01

    A protocol has been developed that produced the type of lunar soil abrasion damage observed on Apollo spacesuits. This protocol was then applied to four materials (Kevlar(Registered TradeMark), Vectran(Registered TradeMark), Orthofabric, and Tyvek(Registered TradeMark)) that are candidates for advanced spacesuits. Three of the four new candidate fabrics (all but Vectran(Registered TradeMark)) were effective at keeping the dust from penetrating to layers beneath. In the cases of Kevlar(Registered TradeMark) and Orthofabric this was accomplished by the addition of a silicone layer. In the case of Tyvek , the paper structure was dense enough to block dust transport. The least abrasive damage was suffered by the Tyvek(Registered TradeMark). This was thought to be due in large part to its non-woven paper structure. The woven structures were all abraded where the top of the weave was struck by the abrasive. Of these, the Orthofabric suffered the least wear, with both Vectran(Registered TradeMark) and Kevlar(Registered TradeMark) suffering considerably more extensive filament breakage.

  17. Raman characterization of damaged layers of 4H-SiC induced by scratching

    NASA Astrophysics Data System (ADS)

    Nakashima, Shin-ichi; Mitani, Takeshi; Tomobe, Masaru; Kato, Tomohisa; Okumura, Hajime

    2016-01-01

    Recent development of device fabrication of SiC is awaiting detailed study of the machining of the surfaces. We scratched 4H-SiC surfaces with a sliding microindenter made of a SiC chip, and characterized machining affected layers by micro-Raman spectroscopy. The results of the Raman measurement of the scratching grooves revealed that there were residual stress, defects, and stacking faults. Furthermore, with heavy scratching load, we found clusters of amorphous SiC, Si, amorphous carbon, and graphite in the scratching grooves. Analysis of the Raman spectra showed that SiC amorphization occurs first and surface graphitization (carbonization) is subsequently generated through the phase transformation of SiC. We expect that the Raman characterization of machined surfaces provides information on the machining mechanism for compound semiconductors.

  18. Cortical GluK1 kainate receptors modulate scratching in adult mice.

    PubMed

    Descalzi, Giannina; Chen, Tao; Koga, Kohei; Li, Xiang-Yao; Yamada, Kaori; Zhuo, Min

    2013-09-01

    Recent investigations into the mechanisms mediating itch transmission have focused on spinal mechanisms, whereas few studies have investigated the role of the cerebral cortex in itch-related behaviors. Human imaging studies show that several cortical regions are active in correspondence with itch, including the anterior cingulate cortex (ACC). We present here evidence of cortical modulation of pruritogen-induced scratching behavior. We combine pharmacological, genetic, and electrophysiological approaches to show that cortical GluK1-containing kainate (KA) receptors are involved in scratching induced by histamine and non-histamine-dependent itching stimuli. We further show that scratching corresponds with enhanced excitatory transmission in the ACC through KA receptor modulation of inhibitory circuitry. In addition, we found that inhibiting GluK1-containing KA receptors in the ACC also reduced behavioral nociceptive responses induced by formalin. Our results reveal a new role of the cortex in pruritogen-induced scratching. PMID:23786569

  19. IPV--bridging the juridical gap between scratches and DNA detection under fingernails of cohabitating partners.

    PubMed

    Kettner, M; Cappel-Hoffmann, S; Makuch, D; Schmidt, P; Ramsthaler, F

    2015-01-01

    Intimate partner violence (IPV) is a global health issue with lifetime prevalences of physical and sexual violence against women of 12-71% in various populations. Due to its clandestine nature third party eye witnesses are scarce and prosecution of these cases has to rely on medical examination results, e.g. injury patterns of the victim and the perpetrator. Medicolegal assessment of DNA of the male partner found in fingernail specimen of the female partner after an assault is difficult since cohabitating couples are known to carry DNA of the respective partner in 17% of examined couples. In this study, male and total DNA content in fingernail specimen of 34 couples was analyzed after vigorous scratching of the male partners flank. Scratching and non-scratching fingers showed a highly significant difference in absolute and relative male DNA content allowing for the differentiation of DNA transfer caused by normal cohabitation and scratching during an assault. PMID:25450781

  20. Physiological and Behavioral Responses of Horses to Wither Scratching and Patting the Neck When Under Saddle.

    PubMed

    Thorbergson, Zoë W; Nielsen, Sharon G; Beaulieu, Rodney J; Doyle, Rebecca E

    2016-01-01

    Riding is considered to be an arousing activity for horses. It has been suggested that wither scratching may be a more useful tool for relaxation compared with the common practice of neck patting. In the current study, 18 horses were exposed to 3 treatments, including control or no interaction, neck patting, and wither scratching, for 1 min each following a short obstacle course. Heart rate, heart rate variability, and a variety of behaviors were measured in the horses. Wither scratching produced a significantly longer duration of relaxed-type behaviors. Wither scratching could be a useful tool to help a horse relax while under saddle. Additionally, the study identified 2 ear positions that may be useful for future research in horse behavior. PMID:26958705

  1. A comparison of the tribological behaviour of Y-TZP in tea and coffee under micro-abrasion conditions

    NASA Astrophysics Data System (ADS)

    Sharifi, S.; Stack, M. M.

    2013-10-01

    The micro-abrasion of Y-TZP, a candidate dental restorative material, was investigated in a range of caffeine-containing solutions which included tea and coffee. Additions of sugar and milk were used to test the effects of viscosity and pH on the wear rate. The results indicated a significant increase in wear rate in the various solutions, with some correlation between wear rate and increases in viscosity and this was linked to enhance particle entrainment in the more viscous solutions. The generally lower wear rate in tea compared to coffee was associated with a longer ageing period in this solution before uniform wear was observed. Micro-abrasion maps were used to characterize the differences in performance for the material in the environments studied.

  2. Machining of Aircraft Titanium with Abrasive-Waterjets for Fatigue Critical Applications

    SciTech Connect

    Liu, H. T.; Hovanski, Yuri; Dahl, Michael E.

    2012-02-01

    Laboratory tests were conducted to determine the fatigue performance of abrasive-waterjet- (AWJ-) machined aircraft titanium. Dog-bone specimens machined with AWJs were prepared and tested with and without sanding and dry-grit blasting with Al2O3 as secondary processes. The secondary processes were applied to remove the visual appearance of AWJ-generated striations and to clean up the garnet embedment. The fatigue performance of AWJ-machined specimens was compared with baseline specimens machined with CNC milling. Fatigue test results of the titanium specimens not only confirmed our previous findings in aluminum dog-bone specimens but in comparison also further enhanced the fatigue performance of the titanium. In addition, titanium is known to be difficult to cut, particularly for thick parts, however AWJs cut the material 34% faster han stainless steel. AWJ cutting and dry-grit blasting are shown to be a preferred ombination for processing aircraft titanium that is fatigue critical.

  3. [Composites versus amalgam: comparative measurements of abrasion resistance in vivo: 1-year results].

    PubMed

    Meier, C; Lutz, F

    1979-03-01

    A method for the in-vivo measurement of wear resistance of restorative materials is described. A profilometer is used to record the reduction in vertical dimension of the test material's occlusal surface. This loss of substance is calculated as the wear resistance index. The technique was used in a 13 month clinical evaluation of 3 different restorative materials, Adaptic, Amalgam (Dispersalloy) and Estic microfill. The procedure is simple in execution and very accurate. Statistical analysis has shown significant differences in wear resistance of the examined materials independent of patient variation. Attrition and abrasion were definitely greater with a standard composite material (Adaptic) than with amalgam and a test composite (Estic microfill). The newly developed composite material utilizing extremely fine filler particles of pyrogenic SiO2 (Estic microfill) was shown to be comparable to amalgam in wear resistance during the 13-month test period. PMID:293032

  4. Characterization of scratching behavior induced by intradermal administration of morphine and fentanyl in mice.

    PubMed

    Yamamoto, Atsuki; Kuyama, Shoji; Kamei, Chiaki; Sugimoto, Yukio

    2010-02-10

    Itching is known as a commonly side effect of opioid administration. However, the relationship of opioid receptors to itching is unclear. In this study, we examined the effect of intradermal injection of morphine and fentanyl on the itching sensation. When injected intradermally into the rostral back of mice, morphine and fentanyl elicited scratching behavior. In addition, an opioid receptor antagonist, naloxone, and a peripherally restricted opioid receptor antagonist, naloxone methiodide, significantly suppressed morphine- and fentanyl-induced scratching behavior. Moreover, the morphine-induced scratching behavior was suppressed by histamine H(1) receptor antagonists, such as diphenhydramine, chlorpheniramine, epinastine and cetirizine. On the other hand, fentanyl-induced scratching behavior was not suppressed by histamine H(1) receptor antagonists. Additionally, scratching behavior induced by morphine and fentanyl were not suppressed by glucocorticoids (predonisolone and dexamethasone). In conclusion, opioid-induced itching may involve in peripheral opioid receptors. Moreover, histamine and arachidonic acid metabolites played no main role in opioid-induced scratching behavior. PMID:19900440

  5. A novel approach of high speed scratching on silicon wafers at nanoscale depths of cut.

    PubMed

    Zhang, Zhenyu; Guo, Dongming; Wang, Bo; Kang, Renke; Zhang, Bi

    2015-01-01

    In this study, a novel approach of high speed scratching is carried out on silicon (Si) wafers at nanoscale depths of cut to investigate the fundamental mechanisms in wafering of solar cells. The scratching is conducted on a Si wafer of 150 mm diameter with an ultraprecision grinder at a speed of 8.4 to 15 m/s. Single-point diamonds of a tip radius of 174, 324, and 786 nm, respectively, are used in the study. The study finds that at the onset of chip formation, an amorphous layer is formed at the topmost of the residual scratch, followed by the pristine crystalline lattice beneath. This is different from the previous findings in low speed scratching and high speed grinding, in which there is an amorphous layer at the top and a damaged layer underneath. The final width and depth of the residual scratch at the onset of chip formation measured vary from 288 to 316 nm, and from 49 to 62 nm, respectively. High pressure phases are absent from the scratch at the onset of either chip or crack formation. PMID:26548771

  6. A novel approach of high speed scratching on silicon wafers at nanoscale depths of cut

    NASA Astrophysics Data System (ADS)

    Zhang, Zhenyu; Guo, Dongming; Wang, Bo; Kang, Renke; Zhang, Bi

    2015-11-01

    In this study, a novel approach of high speed scratching is carried out on silicon (Si) wafers at nanoscale depths of cut to investigate the fundamental mechanisms in wafering of solar cells. The scratching is conducted on a Si wafer of 150 mm diameter with an ultraprecision grinder at a speed of 8.4 to 15 m/s. Single-point diamonds of a tip radius of 174, 324, and 786 nm, respectively, are used in the study. The study finds that at the onset of chip formation, an amorphous layer is formed at the topmost of the residual scratch, followed by the pristine crystalline lattice beneath. This is different from the previous findings in low speed scratching and high speed grinding, in which there is an amorphous layer at the top and a damaged layer underneath. The final width and depth of the residual scratch at the onset of chip formation measured vary from 288 to 316 nm, and from 49 to 62 nm, respectively. High pressure phases are absent from the scratch at the onset of either chip or crack formation.

  7. A novel approach of high speed scratching on silicon wafers at nanoscale depths of cut

    PubMed Central

    Zhang, Zhenyu; Guo, Dongming; Wang, Bo; Kang, Renke; Zhang, Bi

    2015-01-01

    In this study, a novel approach of high speed scratching is carried out on silicon (Si) wafers at nanoscale depths of cut to investigate the fundamental mechanisms in wafering of solar cells. The scratching is conducted on a Si wafer of 150 mm diameter with an ultraprecision grinder at a speed of 8.4 to 15 m/s. Single-point diamonds of a tip radius of 174, 324, and 786 nm, respectively, are used in the study. The study finds that at the onset of chip formation, an amorphous layer is formed at the topmost of the residual scratch, followed by the pristine crystalline lattice beneath. This is different from the previous findings in low speed scratching and high speed grinding, in which there is an amorphous layer at the top and a damaged layer underneath. The final width and depth of the residual scratch at the onset of chip formation measured vary from 288 to 316 nm, and from 49 to 62 nm, respectively. High pressure phases are absent from the scratch at the onset of either chip or crack formation. PMID:26548771

  8. Development and validation of an alternative disturbed skin model by mechanical abrasion to study drug penetration

    PubMed Central

    Schlupp, P.; Weber, M.; Schmidts, T.; Geiger, K.; Runkel, F.

    2014-01-01

    Pharmaceuticals and cosmetics for dermal application are usually tested on healthy skin, although the primary permeation barrier, the stratum corneum, is often impaired by skin diseases or small skin lesions, especially on the hands. These skin conditions can considerably influence the permeation of chemicals and drugs. Furthermore, risk assessment for example of nanoparticles should be performed under various skin conditions to reflect the true circumstances. Therefore, an alternative and reproducible method for a high throughput of skin samples with impaired skin barrier was developed and verified by skin permeation studies (25 h) of caffeine, sorbic acid and testosterone compared to healthy (untreated) and tape-stripped skin. Skin barrier disruption was controlled by TEWL measurement. Skin permeation of the three substances was increased in tape-stripped and abraded skin compared to untreated skin due to the reduced barrier integrity. Enhancement of drug uptake was highest for the most hydrophilic substance, caffeine, followed by sorbic acid and lipophilic testosterone. No significant difference in drug uptake studies was observed between the new abrasion method with an aluminum-coated sponge and the tape-stripping method. The obtained results demonstrate that this abrasion method is an alternative way to achieve a disturbed skin barrier for drug and chemical uptake studies. PMID:25756004

  9. Dental abrasion as a cutting process.

    PubMed

    Lucas, Peter W; Wagner, Mark; Al-Fadhalah, Khaled; Almusallam, Abdulwahab S; Michael, Shaji; Thai, Lidia A; Strait, David S; Swain, Michael V; van Casteren, Adam; Renno, Waleed M; Shekeban, Ali; Philip, Swapna M; Saji, Sreeja; Atkins, Anthony G

    2016-06-01

    A mammalian tooth is abraded when a sliding contact between a particle and the tooth surface leads to an immediate loss of tooth tissue. Over time, these contacts can lead to wear serious enough to impair the oral processing of food. Both anatomical and physiological mechanisms have evolved in mammals to try to prevent wear, indicating its evolutionary importance, but it is still an established survival threat. Here we consider that many wear marks result from a cutting action whereby the contacting tip(s) of such wear particles acts akin to a tool tip. Recent theoretical developments show that it is possible to estimate the toughness of abraded materials via cutting tests. Here, we report experiments intended to establish the wear resistance of enamel in terms of its toughness and how friction varies. Imaging via atomic force microscopy (AFM) was used to assess the damage involved. Damage ranged from pure plastic deformation to fracture with and without lateral microcracks. Grooves cut with a Berkovich diamond were the most consistent, suggesting that the toughness of enamel in cutting is 244 J m(-2), which is very high. Friction was higher in the presence of a polyphenolic compound, indicating that this could increase wear potential. PMID:27274807

  10. Ozone mediators effect on "in vitro" scratch wound closure.

    PubMed

    Valacchi, Giuseppe; Sticozzi, Claudia; Zanardi, Iacopo; Belmonte, Giuseppe; Cervellati, Franco; Bocci, Velio; Travagli, Valter

    2016-09-01

    The beneficial effect of low doses of ozone on wound healing has been well documented and attributed mainly to its bactericidal and pro-oxidant properties. Because ozone itself does not penetrate the cells but immediately reacts with polyunsaturated fatty acids, its effects are the results of oxidative mediators. Among the molecule produces by the interaction of ozone with biological systems, there are HNE and H2O2. At today, the cellular mechanisms accounting for the positive effects of mild ozonization on wound closure are still largely unexplored. The aim of the present study was to evaluate the effect of different non-toxic doses of ozonated saline ranging from 2 to 300 μM, in an in vitro wound scratch model by the use of human keratinocytes. The results showed that ozonated saline is able to improve in vitro wound healing by stimulating cell proliferation as measured by BrdU assay and PCNA protein levels. In order to better elucidate the molecules that play the main role in the beneficial effect of ozonated saline in wound healing, HNE and H2O2 were used alone or in combination to mimic ozonated saline effect. Surprisingly, keratinocytes treated with different doses of HNE and H2O2 did not significantly improve the wound closure, while the combination of the two compounds was able to improve wound closure. In addition, Nrf2 pathways were also activated as determined by its translocation to the nucleus and the increased HO1 gene expression. The present work suggests that ozonated saline effect on wound closure is the results of the combination of more molecules among which HNE and H2O2 play a key role. PMID:27487012

  11. Nano-scratch behavior of a bulk Zr-10Al-5Ti-17.9Cu-14.6Ni amorphous alloy

    SciTech Connect

    Wang, J. G.; Choi, B. W.; Nieh, T. G.; Liu, C. T.

    2000-04-01

    The tribological behavior of a Zr-10Al-5Ti-17.9Cu-14.6Ni (at.%) bulk amorphous alloy, in both the as-cast and annealed states, was investigated using nano-scratch tests, including ramping load scratch and multiple sliding wear techniques. The crystallization sequence of the alloy was also characterized. Mechanical properties, such as Young's modulus, hardness, friction coefficient, and tribological wear were measured. These properties were found to vary with microstructure. In general, an increase in annealing temperature results in an increase in hardness, which in turn produces a decrease in friction coefficient but an increase in wear resistance. Samples having a structure consisting of supercooled liquid matrix with dispersed nanocrystalline particles exhibit the best wear performance. (c) 2000 Materials Research Society.

  12. The agar diffusion scratch assay - A novel method to assess the bioactive and cytotoxic potential of new materials and compounds

    PubMed Central

    Pusnik, Mascha; Imeri, Minire; Deppierraz, Grégoire; Bruinink, Arie; Zinn, Manfred

    2016-01-01

    A profound in vitro evaluation not only of the cytotoxic but also of bioactive potential of a given compound or material is crucial for predicting potential effects in the in vivo situation. However, most of the current methods have weaknesses in either the quantitative or qualitative assessment of cytotoxicity and/or bioactivity of the test compound. Here we describe a novel assay combining the ISO 10993-5 agar diffusion test and the scratch also termed wound healing assay. In contrast to these original tests this assay is able to detect and distinguish between cytotoxic, cell migration modifying and cytotoxic plus cell migration modifying compounds, and this at higher sensitivity and in a quantitative way. PMID:26861591

  13. Comparison of surface abrasion produced on the enamel surface by a standard dentifrice using three different toothbrush bristle designs: A profilometric in vitro study

    PubMed Central

    Kumar, Sandeep; Kumari, Minal; Acharya, Shashidhar; Prasad, Ram

    2014-01-01

    Aim: The aim was to assess, in vitro, the effect on surface abrasivity of enamel surface caused by three different types (flat trim, zig-zag, bi-level) of toothbrush bristle design. Materials and Methods: Twenty-four freshly extracted, sound, human incisor teeth were collected for this study. The enamel slab was prepared, which were mounted, on separate acrylic bases followed by subjected to profilometric analysis. The surface roughness was measured using the profilometer. The specimen were divided into three groups, each group containing eight mounted specimens, wherein, Group 1 specimens were brushed with flat trim toothbrush; Group 2 brushed with zig-zag and Group 3 with bi-level bristle design. A commercially available dentifrice was used throughout the study. A single specimen was brushed for 2 times daily for 2 min period for 1 week using a customized brushing apparatus. The pre- and post-roughness value change were analyzed and recorded. Statistical test: Kruskal–Wallis test and Mann–Whitney U-test. Result: The results showed that surface abrasion was produced on each specimen, in all the three groups, which were subjected to brushing cycle. However, the bi-level bristle design (350% increase in roughness, P = 0.021) and zig-zag bristle design (160% increase in roughness, P = 0.050) showed significantly higher surface abrasion when compared with flat trim bristle design toothbrush. Conclusion: Flat trim toothbrush bristle produces least surface abrasion and is relatively safe for use. PMID:25125852

  14. The effect of hydrogen peroxide on polishing removal rate in CMP with various abrasives

    NASA Astrophysics Data System (ADS)

    Manivannan, R.; Ramanathan, S.

    2009-01-01

    The effect of hydrogen peroxide in chemical mechanical planarization slurries for shallow trench isolation was investigated. The various abrasives used in this study were ceria, silica, alumina, zirconia, titania, silicon carbide, and silicon nitride. Hydrogen peroxide suppresses the polishing of silicon dioxide and silicon nitride surfaces by ceria abrasives. The polishing performances of other abrasives were either unaffected or enhanced slightly with the addition of hydrogen peroxide. The ceria abrasives were treated with hydrogen peroxide, and the polishing of the work surfaces with the treated abrasive shows that the inhibiting action of hydrogen peroxide is reversible. It was found that the effect of hydrogen peroxide as an additive is a strong function of the nature of the abrasive particle.

  15. Functional photocatalytically active and scratch resistant antireflective coating based on TiO2 and SiO2

    NASA Astrophysics Data System (ADS)

    Mazur, M.; Wojcieszak, D.; Kaczmarek, D.; Domaradzki, J.; Song, S.; Gibson, D.; Placido, F.; Mazur, P.; Kalisz, M.; Poniedzialek, A.

    2016-09-01

    Antireflection (AR) multilayer coating, based on combination of five TiO2 and SiO2 thin films, was deposited by microwave assisted reactive magnetron sputtering process on microscope glass substrates. In this work X-ray diffraction, X-ray photoelectron spectroscopy, atomic force microscopy and wettability measurements were used to characterize the structural and surface properties of the deposited coating. These studies revealed that prepared coating was amorphous with low surface roughness. Photocatalytic properties were determined based on phenol decomposition reaction. Measurements of optical properties showed that transmittance in the visible wavelength range was increased after the deposition of AR coating as-compared to bare glass substrate. The mechanical properties were determined on the basis of nano-indentation and scratch resistance tests. Performed research has shown that deposition of an additional thin 10 nm thick TiO2 thin film top layer, the prepared AR coating was photocatalytically active, hydrophobic, scratch resistant and had increased hardness as-compared to bare glass substrate. These results indicate that prepared AR multilayer could be used also as a self-cleaning and protective coating.

  16. Cat-Scratch Disease In Adult Hospitalized For Prolonged-Fever Associated With Multiple Lymphadenopathies and Weight Loss

    PubMed Central

    Guiyedi, Vincent; Haddad, Hanna; Okome-Nkoumou, Madeleine; Gire, Fabien; Ongali, Brice; Lore, Philippes; Gameiro, Luis

    2013-01-01

    We report a 19-year-old patient with a Cat-scratch disease presenting three months continuous alteration of the general condition, including prolonged-fever, anorexia, asthenia, weight loss associated with adenitis and multiple thoracic-abdominal adenopathies, leukocytosis with neutrophil polynuclear predominance, and increased of C-reactive protein. The serologies of toxoplasmosis, infectious mononucleosis, human immunodeficiency virus, Brucellosis, Bartonellosis and the tuberculosis research by tuberculin reaction test and Ziehl acid-alcohol resistant bacilli direct examination were negatives. The cytomegalovirus and Epstein-Barr virus serologies were positives only for immunoglobulin-G. The Bartonella henselae diagnosis was made with the analysis of histopathological specimens. The clinical and biological symptoms regressed following eight weeks of azithromycin's treatment. According to this observation, the cat-scratch disease should be considered in differential diagnosis of patients presenting prolonged-fever associated with multiple lymphadenopathies and weight loss. The azithromycin would be an alternative therapeutic issue for this pathology in case of confirmed efficacy by studies in a large patient population. PMID:24403980

  17. Improvement in Abrasion Wear Resistance and Microstructural Changes with Deep Cryogenic Treatment of Austempered Ductile Cast Iron (ADI)

    NASA Astrophysics Data System (ADS)

    Šolić, Sanja; Godec, Matjaž; Schauperl, Zdravko; Donik, Črtomir

    2016-07-01

    The application of a deep cryogenic treatment during the heat-treatment processes for different types of steels has demonstrated a significant influence on their mechanical and tribological properties. A great deal of research was conducted on steels, as well as on other kinds of materials, such as hard metal, gray cast iron, aluminum, aluminum alloys, etc., but not on austempered ductile iron (ADI). In this research the influence of a deep cryogenic treatment on the microstructure and abrasive wear resistance of austempered ductile iron was investigated. The ductile cast iron was austempered at the upper ausferritic temperature, deep cryogenically treated, and afterwards tempered at two different temperatures. The abrasion wear resistance was tested using the standard ASTM G65 method. The microstructure was characterized using optical microscopy, field-emission scanning electron microscopy, electron back-scattered diffraction, and X-ray diffraction in order to define the microstructural changes that influenced the properties of the ADI. The obtained results show that the deep cryogenic treatment, in combination with different tempering temperatures, affects the matrix microstructure of the austempered ductile iron, which leads to an increase in both the abrasion wear resistance and the hardness.

  18. Investigation of test methods, material properties, and processes for solar cell encapsulants. Encapsulation task of the Low-Cost Silicon Solar Array project. Thirteenth quarterly progress report, May 12, 1979-August 12, 1979

    SciTech Connect

    1980-01-01

    Springborn Laboratories is engaged in a study of evaluating potentially useful encapsulating materials for Task 3 of the Low-Cost Silicon Solar Array project (LSA) funded by DOE. The goal of this program is to identify, evaluate, and recommend encapsulant materials and processes for the product of cost-effective, long-life solar cell modules. Current technical activities are directed primarily towards the development of a solar module encapsulation technology that employs ethylene/vinyl acetate copolymer as the pottant. Due to the surface tack of EVA, a slip sheet of release paper is required between each layer to prevent the plies from adhering. Manufacturers were surveyed and a source for inexpensive release paper in roll form was identified. A survey of separator materials was also conducted. Corrosion studies using a standard salt spray test were used to determine the degree of protection offered to a variety of metals by encapsulation in EVA pottant. Due to the low surface hardness of EVA and the remaining sensitivity to ultraviolet light, outer covers are required to prevent soiling and improve the weatherability. Two candidate films (Korad 212 and Tedlar UT) have been identified for this function. These films are somewhat scratch and abrasion sensitive, however, and their useful life can be prolonged with the application of thin layers of abrasion resistant hard coats. A survey of manufacturers of these coatings was performed and the products compared. Field trials of outdoor performance must be performed to fully assess the durability of these coatings.

  19. Reduction of sodium deoxycholic acid-induced scratching behaviour by bradykinin B2 receptor antagonists

    PubMed Central

    Hayashi, Izumi; Majima, Masataka

    1999-01-01

    Subcutaneous injection of sodium deoxycholic acid into the anterior of the back of male ddY mice elicited dose-dependent scratching of the injected site with the forepaws and hindpaws.Up to 100 μg of sodium deoxycholic acid induced no significant increase in vascular permeability at the injection site as assessed by a dye leakage method.Bradykinin (BK) B2 receptor antagonists, FR173657 and Hoe140, significantly decreased the frequency of scratching induced by sodium deoxycholic acid.Treatment with aprotinin to inhibit tissue kallikrein reduced the scratching behaviour induced by sodium deoxycholic acid, whereas treatment with soybean trypsin inhibitor to inhibit plasma kallikrein did not.Although injection of kininase II inhibitor, lisinopril together with sodium deoxycholic acid did not alter the scratching behaviour, phosphoramidon, a neutral endopeptidase inhibitor, significantly increased the frequency of scratching.Homogenates of the skin excised from the backs of mice were subjected to gel-filtration column chromatography followed by an assay of kinin release by trypsin from each fraction separated. Less kinin release from the fractions containing kininogen of low molecular weight was observed in the skin injected with sodium deoxycholic acid than in normal skin.The frequency of scratching after the injection of sodium deoxycholic acid in plasma kininogen-deficient Brown Norway Katholiek rats was significantly lower than that in normal rats of the same strain, Brown Norway Kitasato rats.These results indicate that BK released from low-molecular-weight kininogen by tissue kallikrein, but not from high-molecular-weight kininogen by plasma kallikrein, may be involved in the scratching behaviour induced by the injection of sodium deoxycholic acid in the rodent. PMID:10051136

  20. A comparison of the abrasiveness of six ceramic surfaces and gold.

    PubMed

    Jacobi, R; Shillingburg, H T; Duncanson, M G

    1991-09-01

    A type III gold alloy and six different ceramic surfaces were secured in an abrasion machine opposing extracted teeth to determine their relative abrasiveness and resistance to wear. The rankings of restorative materials from least abrasive to most abrasive were: gold alloy, polished; cast ceramic, polished; porcelain, polished; cast ceramic, polished and shaded; porcelain, polished and glazed; cast ceramic, cerammed skin shaded; and cast ceramic, cerammed skin unshaded. The ranking of materials from most wear-resistant to least wear-resistant was: gold alloy, cast ceramic cerammed, cast ceramic cerammed and shaded, porcelain polished, porcelain glazed, cast ceramic polished and shaded, and cast ceramic polished. PMID:1800724

  1. A rotary-airlock valve resists abrasive mixtures

    SciTech Connect

    Not Available

    1993-03-01

    Hill and Griffith (H and G, Cincinnati, Ohio) is a leading supplier of custom-blended additives to founderies. Thousands of tons of clay and carbon blends such as bentonite, gilsonite and pulverized coal, pass through the company's rotary-airlock feeding system each month. H and G's original rotary valves had cylinders lined with chrome, and closed-end rotors with tips made from nickel-chromium alloys. These valves remained in service for a maximum of only three months each. During that time, the abrasive mixtures passing through the valves virtually eroded them, increasing tolerances and causing significant air leakage. The leaks caused the pneumatic line to plug up, reducing the velocity of the line below the minimum level needed to carry any material. To overcome the leakage, a second blower was added to the system. This unit supplied an additional 40 brake hp to the pneumatic-conveying line. With constant maintenance of the valve and the continuous operation of both blowers, H and G was able to extend the valve's life by nine months. After 20 years of trying valves with various configuration, H and G installed a Smoot Type 6 rotary-airlock valve in September of 1985. The new valve's internals were made from abrasion-resistant grades of NiHard and Stellite. This combination of alloys prolonged the active life of the valve by improving its abrasion resistance. During its first year, the Smoot valve did not break down, leak air or require use of the secondary blower. After its first year of service no wear was found on the valve's internal surfaces. Another mechanical analysis was performed in 1991, after five additional years of valve operation. The valve, which had now handled more than 250,000 tons of product, showed minimal wear. H and G's capital costs had been reduced from 25[cents]/ton to 3[cents]/ton by the new valve.

  2. Abrasion in pyroclastic density currents: Insights from tumbling experiments

    NASA Astrophysics Data System (ADS)

    Kueppers, Ulrich; Putz, Constanze; Spieler, Oliver; Dingwell, Donald B.

    2012-01-01

    During granular mass movements of any kind, particles may interact with one another. The degree of interaction is a function of several variables including; grain-size distribution, particle concentration, density stratification and degree of fluidisation. The impact of particle interaction is additionally influenced by the relative speed, impact angle and clast temperature. Thus, both source conditions and transport-related processes are expected to influence the flow dynamics of pyroclastic density currents and their subsequent deposition. Here, we use tumbling experiments to shed light on the susceptibility of porous clasts to abrasion. We investigated the abrasion of unaltered volcanic rocks (5.7-80 vol.% porosity) from Unzen (Japan), Bezymianny (Russia) and Santorini (Greece) volcanoes as well as one synthetic analogue material, an insulating material with the trade name Foamglas® (95 vol.% porosity). Each experiment started with angular fragments generated in a jaw crusher from larger clasts. Two experimental series were performed; on samples with narrow and broader grain-size distributions, respectively. The dry samples were subject to rotational movement at constant speed and ambient temperature in a gum rotational tumbler for durations of 15, 30, 45, 60 and 120 min. The amount of volcanic ash (particles <2 mm) generated was evaluated as a function of experimental duration and sample porosity. We term “abrasion” as the ash fraction generated during the experiments. The observed increase of “abrasion” with increasing sample porosity and experimental duration is initially non-linear but becomes linear for experiments of 30 min duration or longer. For any given sample, abrasion appears to be more effective for coarser samples and larger initial mass. The observed range of ash generated in our experiments is between 1 and 35 wt.%. We find that this amount generally increases with increasing initial clast size or increasing breadth of the initial grain

  3. Heat sealable, flame and abrasion resistant coated fabric

    NASA Technical Reports Server (NTRS)

    Tschirch, R. P.; Sidman, K. R. (Inventor)

    1983-01-01

    Flame retardant, abrasion resistant elastomeric compositions are disclosed which are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Heat sealable coated fabrics employing such elastomeric compositions as coating film are produced by dissolving the elastomeric composition to form a solution, casting the solution onto a release paper and drying it to form an elastomeric film. The film is then bonded to a woven, knitted, or felted fabric.

  4. Influence of Air Abrasion and Sonic Technique on Microtensile Bond Strength of One-Step Self-Etch Adhesive on Human Dentin

    PubMed Central

    Anja, Baraba; Walter, Dukić; Nicoletta, Chieffi; Marco, Ferrari; Pezelj Ribarić, Sonja; Ivana, Miletić

    2015-01-01

    The purpose of this in vitro study was to evaluate the microtensile bond strength of one-step self-etch adhesive to human dentin surface modified with air abrasion and sonic technique and to assess the morphological characteristics of the pretreated dentin surface. The occlusal enamel was removed to obtain a flat dentin surface for thirty-six human molar teeth. The teeth were randomly divided into three experimental groups (n = 12 per group), according to the pretreatment of the dentin: (1) control group, (2) air abrasion group, and (3) sonic preparation group. Microtensile bond strength test was performed on a universal testing machine. Two specimens from each experimental group were subjected to SEM examination. There was no statistically significant difference in bond strength between the three experimental groups (P > 0.05). Mean microtensile bond strength (MPa) values were 35.3 ± 12.8 for control group, 35.8 ± 13.5 for air abrasion group, and 37.7 ± 12.0 for sonic preparation group. The use of air abrasion and sonic preparation with one-step self-etch adhesive does not appear to enhance or impair microtensile bond strength in dentin. PMID:25879053

  5. In vitro comparative bond strength of contemporary self-adhesive resin cements to zirconium oxide ceramic with and without air-particle abrasion.

    PubMed

    Blatz, Markus B; Phark, Jin-Ho; Ozer, Fusun; Mante, Francis K; Saleh, Najeed; Bergler, Michael; Sadan, Avishai

    2010-04-01

    This study compared shear bond strengths of six self-adhesive resin cements to zirconium oxide ceramic with and without air-particle abrasion. One hundred twenty zirconia samples were air-abraded (group SB; n = 60) or left untreated (group NO). Composite cylinders were bonded to the zirconia samples with either BisCem (BC), Maxcem (MC), G-Cem (GC), RelyX Unicem Clicker (RUC), RelyX Unicem Applicator (RUA), or Clearfil SA Cement (CSA). Shear bond strength was tested after thermocycling, and data were analyzed with analysis of variance and Holm-Sidak pairwise comparisons. Without abrasion, RUA (8.0 MPa), GC (7.9 MPa), and CSA (7.6 MPa) revealed significantly higher bond strengths than the other cements. Air-particle abrasion increased bond strengths for all test cements (p < 0.001). GC (22.4 MPa) and CSA (18.4 MPa) revealed the highest bond strengths in group SB. Bond strengths of self-adhesive resin cements to zirconia were increased by air-particle abrasion. Cements containing adhesive monomers (MDP/4-META) were superior to other compositions. PMID:19415350

  6. Preparation of small-area Josephson junction using the scratched edge of a Pb/In layer

    SciTech Connect

    Okuyama, K.; Gundlach, K.H.; Hartfuss, H.J.

    1980-11-01

    Superconductor-insulator-superconductor (SIS) Josephson junctions with areas less than 1 ..mu..m/sup 2/ were formed at the scratched edge of the Pb/In electrode. The scratch was made with a razor blade. Notwithstanding the simple technique used for scratching, the yield to get good junction is relatively high. The I-V characteristic with and without 70-GHz radiation is shown.

  7. Urine-marking and ground-scratching by free-ranging Arctic Wolves, Canis lupus arctos, in summer

    USGS Publications Warehouse

    Mech, L.D.

    2006-01-01

    Urine-marking and ground-scratching were observed in an Arctic Wolf (Canis lupus) pack on Ellesmere Island, Nunavut, Canada, during 16 summers between 1986 and 2005. All previously known urination postures and ground-scratching by breeding males and females were seen, and incidence of marking and scratching was greatest when non-pack wolves were present. Observations of urine-marking of food remains supported the conclusion from a captive Wolf study that such marking signals lack of edible food.

  8. Influence of surface roughness and contact load on friction coefficient and scratch behavior of thermoplastic olefins

    NASA Astrophysics Data System (ADS)

    Jiang, Han; Browning, Robert; Fincher, Jason; Gasbarro, Anthony; Jones, Scooter; Sue, Hung-Jue

    2008-05-01

    To study the effects of surface roughness and contact load on the friction behavior and scratch resistance of polymers, a set of model thermoplastic olefins (TPO) systems with various surface roughness ( Ra) levels were prepared and evaluated. It is found that a higher Ra corresponds to a lower surface friction coefficient ( μs). At each level of Ra, μs gets larger as contact load increases, with a greater increase in μs as Ra level increases. It is also observed that with increasing contact load and increasing Ra, the μs tend to level off. In evaluating TPO scratch resistance, a lower μs would delay the onset of ductile drawing-induced fish-scale surface deformation feature, thereby raising the load required to cause scratch visibility. However, as the contact load is further increased, the μs evolves to become scratch coefficient of friction (SCOF) as significant sub-surface deformation and tip penetration occur and material displacement begins, i.e., ploughing. No dependence of Ra and μs on the critical load for the onset of ploughing is observed. In this work, the distinction between μs and SCOF will be illustrated. Approaches for improving scratch resistance of polymers via control of Ra are also discussed.

  9. Characteristics of scratching behavior in ADJM mice (atopic dermatitis from Japanese mice).

    PubMed

    Nakasone, Tasuku; Sato, Takumi; Matsushima, Yoshibumi; Inoue, Toshio; Kamei, Chiaki

    2015-04-01

    In order to elucidate the characteristics of scratching behavior in atopic dermatitis from Japanese mice (ADJM) mice, the effects of some antagonists of pruritogens on this behavior were studied. Both male and female ADJM mice showed frequent scratching behavior around the face, abdomen and back. The number of scratching behavior around the face was greater than on the abdomen and back, and scratching behavior in female mice was significantly more frequent than in male mice. Histamine H1 antagonist, chlorpheniramine, p.o., inhibited this behavior potently and dose-dependently. Histamine H1 antagonist with serotonin 5-TH(5-hydroxytryptamine)2 antagonist, cyproheptadine, also inhibited this behavior. However, NK1 antagonist, aprepitant, p.o., had no significant inhibitory effect even at a dose of 100 mg/kg, p.o., Mu antagonist, naloxone, and kappa agonist, nalfurafine, significantly inhibited this behavior at doses of 0.3 mg/kg, s.c., and 0.01 mg/kg, p.o., respectively. Histamine contents in the skin of ADJM mice were significantly higher than in BALB/c mice. These results strongly indicate that scratching behavior in ADJM mice is related with histamine H1, opioid mu and opioid kappa receptors. PMID:25578901

  10. Effect of mechanical abrasion on the viability, disruption and germination of spores of Bacillus subtilis

    PubMed Central

    Jones, C.A.; Padula, N.L.; Setlow, P.

    2005-01-01

    Aims To elucidate the factors influencing the sensitivity of Bacillus subtilis spores to killing and disruption by mechanical abrasion, and the mechanism of stimulation of spore germination by abrasion. Methods and Results Spores of B. subtilis strains were abraded by shaking with glass beads in liquid or the dry state, and spore killing, disruption and germination were determined. Dormant spores were more resistant to killing and disruption by abrasion than were growing cells or germinated spores. However, dormant spores of the wild-type strain with or without most coat proteins removed, spores of strains with mutations causing spore coat defects, spores lacking their large depot of dipicolinic acid (DPA) and spores with defects in the germination process exhibited essentially identical rates of killing and disruption by abrasion. When spores lacking all nutrient germinant receptors were enumerated by plating directly on nutrient medium, abrasion increased the plating efficiency of these spores before killing them. Spores lacking all nutrient receptors and either of the two redundant cortex-lytic enzymes behaved similarly in this regard, but the plating efficiency of spores lacking both cortex-lytic enzymes was not stimulated by abrasion. Conclusions Dormant spores are more resistant to killing and disruption by abrasion than are growing cells or germinated spores, and neither the complete coats nor DPA are important in spore resistance to such treatments. Germination is not essential for spore killing by abrasion, although abrasion can trigger spore germination by activation of either of the spore’s cortex-lytic enzymes. Significance and Importance This work provides new insight into the mechanisms of the killing, disruption and germination of spores by abrasion and makes the surprising finding that at least much of the spore coat is not important in spore resistance to abrasion. PMID:16313421

  11. Photoresist-Free Patterning by Mechanical Abrasion of Water-Soluble Lift-Off Resists and Bare Substrates: Toward Green Fabrication of Transparent Electrodes

    PubMed Central

    Printz, Adam D.; Chan, Esther; Liong, Celine; Martinez, René S.; Lipomi, Darren J.

    2013-01-01

    This paper describes the fabrication of transparent electrodes based on grids of copper microwires using a non-photolithographic process. The process—“abrasion lithography”—takes two forms. In the first implementation (Method I), a water-soluble commodity polymer film is abraded with a sharp tool, coated with a conductive film, and developed by immersion in water. Water dissolves the polymer film and lifts off the conductive film in the unabraded areas. In the second implementation (Method II), the substrate is abraded directly by scratching with a sharp tool (i.e., no polymer film necessary). The abraded regions of the substrate are recessed and roughened. Following deposition of a conductive film, the lower profile and roughened topography in the abraded regions prevents mechanical exfoliation of the conductive film using adhesive tape, and thus the conductive film remains only where the substrate is scratched. As an application, conductive grids exhibit average sheet resistances of 17 Ω sq–1 and transparencies of 86% are fabricated and used as the anode in organic photovoltaic cells in concert with the conductive polymer, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). Compared to devices in which PEDOT:PSS alone serves as an anode, devices comprising grids of copper/nickel microwires and PEDOT:PSS exhibit lowered series resistance, which manifests in greater fill factor and power conversion efficiency. This simple method of forming micropatterns could find use in applications where cost and environmental impact should be minimized, especially as a potential replacement for the transparent electrode indium tin oxide (ITO) in thin-film electronics over large areas (i.e., solar cells) or as a method of rapid prototyping for laboratory-scale devices. PMID:24358321

  12. Air abrasion experiments in U-Pb dating of zircon

    USGS Publications Warehouse

    Goldich, S.S.; Fischer, L.B.

    1986-01-01

    Air abrasion of zircon grains can remove metamict material that has lost radiogenic Pb and zircon overgrowths that were added during younger events and thereby improve the precision of the age measurements and permit closer estimates of the original age. Age discordance that resulted from a single disturbance of the U-Pb isotopic decay systems, as had been demonstrated by T.E. Krogh, can be considerably reduced, and, under favorable conditions, the ages brought into concordancy. Two or more events complicate the U-Pb systematics, but a series of abrasion experiments can be helpful in deciphering the geologic history and in arriving at a useful interpretation of the probable times of origin and disturbances. In east-central Minnesota, U.S.A., Penokean tonalite gneiss is dated at 1869 ?? 5 Ma, and sheared granite gneiss is shown to have been a high-level granite intrusion at 1982 ?? 5 Ma in the McGrath Gneiss precursor. Tonalite gneiss and a mafic granodiorite in the Rainy Lake area, Ontario, Canada, are dated at 2736 ?? 16 and 2682 ?? 4 Ma, respectively. The tonalitic phase of the Morton Gneiss, southwestern Minnesota, is dated at 3662 ?? 42 Ma. ?? 1986.

  13. Abrasion Resistant Coating and Method of making the same

    SciTech Connect

    Sordelet, Daniel J.; Besser, Matthew F.

    1999-06-25

    An abrasion resistant coating is created by adding a ductile phase to a brittle matrix phase during spray coating where an Al-Cu-Fe quasicrystalline phase (brittle matrix) and an FeAl intermetallic (ductile phase) are combined. This composite coating produces a coating mostly of quasicrystal phase and an inter-splat layer of the FeAl phase to help reduce porosity and cracking within the coating. Coatings are prepared by plasma spraying unblended and blended quasicrystal and intermetallic powders. The blended powders contain 1, 5, 10 and 20 volume percent of the intermetallic powders. The unblended powders are either 100 volume percent quasicrystalline or 100 volume percent intermetallic; these unblended powders were studied for comparison to the others. Sufficient ductile phase should be added to the brittle matrix to transform abrasive wear mode from brittle fracture to plastic deformation, while at the same time the hardness of the composite should not be reduced below that of the original brittle phase material.

  14. Abrasion resistant coating and method of making the same

    DOEpatents

    Sordelet, Daniel J.; Besser, Matthew F.

    2001-06-05

    An abrasion resistant coating is created by adding a ductile phase to a brittle matrix phase during spray coating where an Al--Cu--Fe quasicrystalline phase (brittle matrix) and an FeAl intermetallic (ductile phase) are combined. This composite coating produces a coating mostly of quasicrystal phase and an inter-splat layer of the FeAl phase to help reduce porosity and cracking within the coating. Coatings are prepared by plasma spraying unblended and blended quasicrystal and intermetallic powders. The blended powders contain 1, 5, 10 and 20 volume percent of the intermetallic powders. The unblended powders are either 100 volume percent quasicrystalline or 100 volume percent intermetallic; these unblended powders were studied for comparison to the others. Sufficient ductile phase should be added to the brittle matrix to transform abrasive wear mode from brittle fracture to plastic deformation, while at the same time the hardness of the composite should not be reduced below that of the original brittle phase material.

  15. Prediction Of Abrasive And Diffusive Tool Wear Mechanisms In Machining

    NASA Astrophysics Data System (ADS)

    Rizzuti, S.; Umbrello, D.

    2011-01-01

    Tool wear prediction is regarded as very important task in order to maximize tool performance, minimize cutting costs and improve the quality of workpiece in cutting. In this research work, an experimental campaign was carried out at the varying of cutting conditions with the aim to measure both crater and flank tool wear, during machining of an AISI 1045 with an uncoated carbide tool P40. Parallel a FEM-based analysis was developed in order to study the tool wear mechanisms, taking also into account the influence of the cutting conditions and the temperature reached on the tool surfaces. The results show that, when the temperature of the tool rake surface is lower than the activation temperature of the diffusive phenomenon, the wear rate can be estimated applying an abrasive model. In contrast, in the tool area where the temperature is higher than the diffusive activation temperature, the wear rate can be evaluated applying a diffusive model. Finally, for a temperature ranges within the above cited values an adopted abrasive-diffusive wear model furnished the possibility to correctly evaluate the tool wear phenomena.

  16. Sliding-gate valve for use with abrasive materials

    DOEpatents

    Ayers, Jr., William J.; Carter, Charles R.; Griffith, Richard A.; Loomis, Richard B.; Notestein, John E.

    1985-01-01

    The invention is a flow and pressure-sealing valve for use with abrasive solids. The valve embodies special features which provide for long, reliable operating lifetimes in solids-handling service. The valve includes upper and lower transversely slidable gates, contained in separate chambers. The upper gate provides a solids-flow control function, whereas the lower gate provides a pressure-sealing function. The lower gate is supported by means for (a) lifting that gate into sealing engagement with its seat when the gate is in its open and closed positions and (b) lowering the gate out of contact with its seat to permit abrasion-free transit of the gate between its open and closed positions. When closed, the upper gate isolates the lower gate from the solids. Because of this shielding action, the sealing surface of the lower gate is not exposed to solids during transit or when it is being lifted or lowered. The chamber containing the lower gate normally is pressurized slightly, and a sweep gas is directed inwardly across the lower-gate sealing surface during the vertical translation of the gate.

  17. Attrition and abrasion models for oil shale process modeling

    SciTech Connect

    Aldis, D.F.

    1991-10-25

    As oil shale is processed, fine particles, much smaller than the original shale are created. This process is called attrition or more accurately abrasion. In this paper, models of abrasion are presented for oil shale being processed in several unit operations. Two of these unit operations, a fluidized bed and a lift pipe are used in the Lawrence Livermore National Laboratory Hot-Recycle-Solid (HRS) process being developed for the above ground processing of oil shale. In two reports, studies were conducted on the attrition of oil shale in unit operations which are used in the HRS process. Carley reported results for attrition in a lift pipe for oil shale which had been pre-processed either by retorting or by retorting then burning. The second paper, by Taylor and Beavers, reported results for a fluidized bed processing of oil shale. Taylor and Beavers studied raw, retorted, and shale which had been retorted and then burned. In this paper, empirical models are derived, from the experimental studies conducted on oil shale for the process occurring in the HRS process. The derived models are presented along with comparisons with experimental results.

  18. Comparative study of talc poudrage versus pleural abrasion for the treatment of primary spontaneous pneumothorax†

    PubMed Central

    Moreno-Merino, Sergio; Congregado, Miguel; Gallardo, Gregorio; Jimenez-Merchan, Rafael; Trivino, Ana; Cozar, Fernando; Lopez-Porras, Marta; Loscertales, Jesus

    2012-01-01

    Primary spontaneous pneumothorax is a pathology mainly affecting healthy young patients. Clinical guidelines do not specify the type of pleurodesis that should be conducted, due to the lack of comparative studies on the different techniques. The aim of this study was to compare talc poudrage and pleural abrasion in the treatment of spontaneous pneumothorax. A retrospective comparative study was performed, including 787 patients with primary spontaneous pneumothorax. The 787 patients were classified into two groups: Group A (pleural abrasion) n = 399 and Group B (talc pleurodesis) n = 388. The variables studied were recurrence, surgical time, morbidity and in-hospital length of stay. Statistical analysis was done by an unpaired t-test and Fisher's exact test (SSPS 18.0). Statistically significant differences were observed in the variables: surgical time (A: 46 ± 12.3; B: 37 ± 11.8 min; P < 0.001); length of stay (A: 4.7 ± 2.5; B: 4.3 ± 1.8 days; P = 0.01); apical air camera (A: 25; B: 4; P < 0.001); pleural effusion (A: 6; B: 0; P = 0.05). Talc poudrage shows shorter surgical times and length of stay, and lower re-intervention rates. Morbidity is lower in patients with talc poudrage. Statistically significant differences were not observed in recurrence, persistent air leaks, atelectasis and haemothorax. PMID:22514256

  19. Comparative evaluation of surface properties of enamel and different esthetic restorative materials under erosive and abrasive challenges: An in vitro study

    PubMed Central

    Kaur, Simranjeet; Makkar, Sameer; Kumar, Rajneesh; Pasricha, Shinam; Gupta, Pranav

    2015-01-01

    Introduction: Noncarious tooth surface loss is a normal physiological process occurring throughout the life, but it can often become a problem affecting function, esthetics or cause pain. Aim: The purpose of this study was to assess the effect of erosive and abrasive challenges on the surface microhardness and surface wear of enamel and three different restorative materials, that is, nanofilled composite, microfilled composite and resin-modified glass ionomer cement (RMGIC) by using Vickers microhardness tester and profilometer respectively. Subjects and Methods: Nanofilled composite (Filtek™ Z350 × T), microfilled composite (Heliomolar®) and RMGIC (Fuji II LC) were used in the study. Results: Nanofilled composite resin has the best resistance to erosion and/or abrasion among all the materials tested, followed by microfilled composite and RMGIC respectively. Conclusion: Toothbrush abrasion has a synergistic effect with erosion on substance loss of human enamel, composites, and RMGIC. The susceptibility to acid and/or toothbrush abrasion of human enamel was higher compared to restorative materials. PMID:26752876

  20. Stability analyses of the mass abrasive projectile high-speed penetrating into a concrete target Part III: Terminal ballistic trajectory analyses

    NASA Astrophysics Data System (ADS)

    Wu, H.; Chen, X. W.; Fang, Q.; Kong, X. Z.; He, L. L.

    2015-08-01

    During the high-speed penetration of projectiles into concrete targets (the impact velocity ranges from 1.0 to 1.5 km/s), important factors such as the incident oblique and attacking angles, as well as the asymmetric abrasions of the projectile nose induced by the target-projectile interactions, may lead to obvious deviation of the terminal ballistic trajectory and reduction of the penetration efficiency. Based on the engineering model for the mass loss and nose-blunting of ogive-nosed projectiles established, by using the Differential Area Force Law (DAFL) method and semi-empirical resistance function, a finite differential approach was programmed (PENTRA2D) for predicting the terminal ballistic trajectory of mass abrasive high-speed projectiles penetrating into concrete targets. It accounts for the free-surface effects on the drag force acting on the projectile, which are attributed to the oblique and attacking angles, as well as the asymmetric nose abrasion of the projectile. Its validation on the prediction of curvilinear trajectories of non-normal high-speed penetrators into concrete targets is verified by comparison with available test data. Relevant parametric influential analyses show that the most influential factor for the stability of terminal ballistic trajectories is the attacking angle, followed by the oblique angle, the discrepancy of asymmetric nose abrasion, and the location of mass center of projectile. The terminal ballistic trajectory deviations are aggravated as the above four parameters increase.

  1. Structural transformations, strengthening, and wear resistance of titanium nickelide upon abrasive and adhesive wear

    NASA Astrophysics Data System (ADS)

    Korshunov, L. G.; Pushin, V. G.; Chernenko, N. L.; Makarov, V. V.

    2010-07-01

    Wear resistance and structural transformations upon abrasive and adhesive wear of titanium nickelide Ti49.4Ni50.6 in microcrystalline (MC) and submicrocrystalline (SMC) states have been investigated. It has been shown that the abrasive wear resistance of this alloy exceeds that of the steel 12Kh18N9 by a factor of about 2, that of the steel 110G13 (Hadfield steel), by a factor of 1.3, and is close to that of the steel 95Kh18. Upon adhesive wear in a testing-temperature range from -50 to +300°C, the Ti49.4Ni50.6 alloy, as compared to the steel 12Kh18N9, is characterized by the wear rate that is tens of times smaller and by a reduced (1.5-2.0 times) friction coefficient. The enhanced wear resistance of the Ti49.4Ni50.6 alloy is due to the development of intense strain hardening in it and to a high fracture toughness, which is a consequence of effective relaxation of high contact stresses arising in the surface layer of the alloy. The SMC state produced in the alloy with the help of equal-channel angular pressing (ECAP) has no effect on the abrasive wear resistance of the alloy. The favorable effect of ECAP on the wear resistance of the Ti49.4Ni50.6 alloy takes place under conditions of its adhesive wear at temperatures from -25 to +70°C. The electron-microscopic investigation showed that under conditions of wear at negative and room temperatures in the surface layer (1-5 μm thick) of titanium nickelide there arises a mixed structure consisting of an amorphous phase and nanocrystals of supposedly austenite and martensite. Upon friction at 200-300°C, a nanocrystalline structure of the B2 phase arises near the alloy surface, which, as is the case with the amorphous-nanocrystalline structure, is characterized by significant effective strength and wear resistance.

  2. Cotton Seedling Injury and Recovery from Wind Blown Sand Abrasion: I. Duration of Exposure

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Millions of acres of crops are exposed to wind blown sand abrasion injury each year and in many instances the damage is thought to be sufficiently severe to require replanting. The goal of this study was to determine the effects of wind blown sand abrasion duration on cotton seedlings. Seedlings of...

  3. Cutting Tools, Files and Abrasives. Pre-Apprenticeship Phase 1 Training.

    ERIC Educational Resources Information Center

    Lane Community Coll., Eugene, OR.

    This self-paced student training module on cutting tools, files, and abrasives is one of a number of modules developed for Pre-apprenticeship Phase 1 Training. Purpose of the module is to enable students to identify and explain the proper use and care of various knives, saws, snips, chisels, and abrasives. The module may contain some or all of the…

  4. Process Monitoring Evaluation and Implementation for the Wood Abrasive Machining Process

    PubMed Central

    Saloni, Daniel E.; Lemaster, Richard L.; Jackson, Steven D.

    2010-01-01

    Wood processing industries have continuously developed and improved technologies and processes to transform wood to obtain better final product quality and thus increase profits. Abrasive machining is one of the most important of these processes and therefore merits special attention and study. The objective of this work was to evaluate and demonstrate a process monitoring system for use in the abrasive machining of wood and wood based products. The system developed increases the life of the belt by detecting (using process monitoring sensors) and removing (by cleaning) the abrasive loading during the machining process. This study focused on abrasive belt machining processes and included substantial background work, which provided a solid base for understanding the behavior of the abrasive, and the different ways that the abrasive machining process can be monitored. In addition, the background research showed that abrasive belts can effectively be cleaned by the appropriate cleaning technique. The process monitoring system developed included acoustic emission sensors which tended to be sensitive to belt wear, as well as platen vibration, but not loading, and optical sensors which were sensitive to abrasive loading. PMID:22163477

  5. Effect of canopy leaf distribution on sand transport and abrasion energy

    Technology Transfer Automated Retrieval System (TEKTRAN)

    During times when crop canopies are short or sparse, wind erosion can uncover plant roots, deplete the soil resource, and damage plants by abrasion and desiccation. Few studies have considered the effects of position and number of leaves on sand transport and the distribution of the sand abrasion en...

  6. Potential Use of Abrasive Air-Propelled Agricultural Residues for Weed Control

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A new postemergence weed control tactic is proposed for organic production systems that results in plant abrasion and death upon assault from abrasive grits propelled by compressed air. Grit derived from granulated walnut shells was delivered by a sand blaster at 517 kPa at distances of 30 to 60 cm ...

  7. Multi-Scale Scratch Analysis in Qinghai-Tibet Plateau and its Geological Implications

    NASA Astrophysics Data System (ADS)

    Sun, Yanyun; Yang, Wencai; Yu, Changqing

    2016-04-01

    Multi-scale scratch analysis on a regional gravity field is a new data processing system for depicting three-dimensional density structures and tectonic features. It comprises four modules including the spectral analysis of potential fields, multi-scale wavelet analysis, density distribution inversion, and scratch analysis. The multi-scale scratch analysis method was applied to regional gravity data to extract information about the deformation belts in the Qinghai-Tibet Plateau, which can help reveal variations of the deformation belts and plane distribution features from the upper crust to the lower crust, provide evidence for the study of three-dimensional crustal structures, and define distribution of deformation belts and mass movement. Results show the variation of deformation belts from the upper crust to the lower crust. The deformation belts vary from dense and thin in the upper crust to coarse and thick in the lower crust, demonstrating that vertical distribution of deformation belts resembles a tree with a coarse and thick trunk in the lower part and dense and thin branches at the top. The dense and thin deformation areas in the upper crust correspond to crustal shortening areas, while the thick and continuous deformation belts in the lower crust indicate the structural framework of the plateau. Additionally, the lower crustal deformation belts recognized by the multi-scale scratch analysis coincide approximately with the crustal deformation belts recognized using single-scale scratch analysis. However, deformation belts recognized by the latter are somewhat rough while multi-scale scratch analysis can provide more detailed and accurate results.

  8. Why we scratch an itch: the molecules, cells and circuits of itch

    PubMed Central

    Bautista, Diana M; Wilson, Sarah R; Hoon, Mark A

    2015-01-01

    Itch is described as an irritating sensation that triggers a desire to scratch. However, this definition hardly seems fitting for the millions of people who suffer from intractable itch. Indeed, the Buddhist philosopher Nāgārjuna more aptly stated, “There is pleasure when an itch is scratched. But to be without an itch is more pleasurable still.” Chronic itch is widespread and very difficult to treat. In this review we focus on the molecules, cells and circuits in the peripheral and central nervous systems that drive acute and chronic itch transmission. Understanding the itch circuitry is critical to developing new therapies for this intractable disease. PMID:24473265

  9. Hybrid organic/inorganic coatings for abrasion resistance on plastic and metal substrates

    SciTech Connect

    Wen, J.; Jordens, K.; Wilkes, G.L.

    1996-12-31

    Novel abrasion resistant coatings have been successfully prepared by the sol-gel method. These materials are spin coated onto bisphenol-A polycarbonate, diallyl diglycol carbonate resin (CR-39) sheet, aluminum, and steel substrates and are thermally cured to obtain a transparent coating of a few microns in thickness. Following the curing, the abrasion resistance is measured and compared with an uncoated control. It was found that these hybrid organic/inorganic networks partially afford excellent abrasion resistance to the polycarbonate substrates investigated. In addition to having excellent abrasion resistance comparable to current commercial coatings, some newly developed systems are also UV resistant. Similar coating formulations applied to metals can greatly improve the abrasion resistance despite the fact that the coatings are lower in density than their substrates.

  10. A review of engineering control technology for exposures generated during abrasive blasting operations.

    PubMed

    Flynn, Michael R; Susi, Pam

    2004-10-01

    This literature review presents information on measures for controlling worker exposure to toxic airborne contaminants generated during abrasive blasting operations occurring primarily in the construction industry. The exposures of concern include respirable crystalline silica, lead, chromates, and other toxic metals. Unfortunately, silica sand continues to be widely used in the United States as an abrasive blasting medium, resulting in high exposures to operators and surrounding personnel. Recently, several alternative abrasives have emerged as potential substitutes for sand, but they seem to be underused Some of these abrasives may pose additional metal exposure hazards. In addition, several new and improved technologies offer promise for reducing or eliminating exposures; these include wet abrasive blasting, high-pressure water jetting, vacuum blasting, and automated/robotic systems. More research, particularly field studies, is needed to evaluate control interventions in this important and hazardous operation. PMID:15631059

  11. Comparison of shear bond strength and surface structure between conventional acid etching and air-abrasion of human enamel.

    PubMed

    Olsen, M E; Bishara, S E; Damon, P; Jakobsen, J R

    1997-11-01

    Recently, air-abrasion technology has been examined for potential applications within dentistry, including the field of orthodontics. The purpose of this study was to compare the traditional acid-etch technique with an air-abrasion surface preparation technique, with two different sizes of abrading particles. The following parameters were evaluated: (a) shear bond strength, (b) bond failure location, and (c) enamel surface preparation, as viewed through a scanning electron microscope. Sixty extracted human third molars were pumiced and divided into three groups of 20. The first group was etched with a 37% phosphoric acid gel for 30 seconds, rinsed for 30 seconds, and dried for 20 seconds. The second and third groups were air-abraded with (a) a 50 microm particle and (b) a 90 microm particle of aluminum oxide, with the Micro-etcher microabrasion machine (Danville Engineering Inc.). All three groups had molar stainless steel orthodontic brackets bonded to the buccal surface of each tooth with Transbond XT bonding system (3M Unitek). A Zwick Universal Testing Machine (Calitek Corp.) was used to determine shear bond strengths. The analysis of variance was used to compare the three groups. The Adhesive Remnant Index (ARI) was used to evaluate the residual adhesive on the enamel after bracket removal. The chi square test was used to evaluate differences in the ARI scores among the groups. The significance for all tests was predetermined at p < or = 0.05. The results indicated that there was a significant difference in shear bond strength among the three groups (p = 0.0001). The Duncan Multiple Range test showed a significant decrease in shear bond strength in the air-abraded groups. The chi square test revealed significant differences among the ARI scores of the acid-etched group and the air-abraded groups (chi(2) = 0.0001), indicating no adhesive remained on the enamel surface after debonding when air-abrasion was used. In conclusion, the current findings indicate that

  12. Abrasive wear by diesel engine coal-fuel and related particles

    SciTech Connect

    Ives, L.K.

    1994-09-01

    The purpose of the work summarized in this report was to obtain a basic understanding of the factors which are responsible for wear of the piston ring and cylinder wall surfaces in diesel engines utilizing coal-fuel. The approach included analytical studies using scanning electron microscopy and energy dispersive x-ray analyses to characterize coal-fuel and various combustion particles, and two different wear tests. The wear tests were a modified pin-on-disk test and a block-on-ring test capable of either unidirectional or reciprocating-rotational sliding. The wear tests in general were conducted with mixtures of the particles and lubricating oil. The particles studied included coal-fuel, particles resulting from the combustion of coal fuel, mineral matter extracted during the processing of coal, and several other common abrasive particle types among which quartz was the most extensively examined. The variables studied included those associated with the particles, such as particle type, size, and hardness; variables related to contact conditions and the surrounding environment; and variables related to the type and properties of the test specimen materials.

  13. Involvement of histamine H4 and H1 receptors in scratching induced by histamine receptor agonists in Balb C mice.

    PubMed

    Bell, J K; McQueen, D S; Rees, J L

    2004-05-01

    The role of histamine H(1), H(2), H(3) and H(4) receptors in acute itch induced by histamine was investigated in female BalbC mice. Scratching was induced by intradermal injections of pruritogen into the back of the neck and "itch" assessed by quantifying the scratching evoked. Histamine (0.03-80 micromol), histamine-trifluoromethyl-toluidine (HTMT, H(1) agonist, 0.002-2 micromol), clobenpropit (H(4) agonist, H(3) antagonist, 0.002-0.6 micromol) and to a lesser extent imetit (H(3)/H(4) agonist, 0.03-3 micromol) all induced dose-dependent scratching. Dimaprit (H(2) agonist, 0.04-40 micromol) did not cause scratching. Mepyramine (H(1) antagonist, 20 mg kg(-1), i.p.) reduced scratching evoked by histamine and HTMT, but not that caused by H(3) or H(4) agonists. Thioperamide (H(3)/H(4) antagonist, 20 mg kg(-1), i.p.) reduced scratching induced by histamine, H(3) and H(4) agonists, but not that caused by HTMT. The non-sedating H(1) antagonist, terfenadine, also significantly reduced the scratching induced by the H(1) agonist, HTMT. Cimetidine (H(2) antagonist, 20 mg kg(-1), i.p.) did not affect histamine-induced scratching. These results indicate that activation of histamine H(4) receptors causes itch in mice, in addition to the previously recognised role for H(1) receptors in evoking itch. Histamine H(4) receptor antagonists therefore merit investigation as antipruritic agents. PMID:15066908

  14. Polyester and epoxy resins: Abrasion resistance. (Latest citations from the Rubber and Plastics Research Association database). Published Search

    SciTech Connect

    Not Available

    1994-06-01

    The bibliography contains citations concerning techniques and materials for enhanced wear and abrasion resistance of polyester and epoxy resins. Topics include test procedures and results, compounds and additives, forming processes, reinforcement effects, and applications. Electrical insulation, linings and coatings for numerous substrates, solar control film glazing material, hoses, material to rebuild worn metal parts, pipes, boats, industrial floor coverings, and ladder rungs are among the applications discussed. Trade name materials and manufacturers are included. (Contains a minimum of 130 citations and includes a subject term index and title list.)

  15. High grade abrasive product development from virtified industrial waste

    SciTech Connect

    Blume, R.D.; Drummond, C.H. III; Sarko, A.

    1996-12-31

    Recent developments in environmental legislation, as well as economic incentives such as the increasing cost of landfilling, have led to a paradigm shift away from encapsulation of hazardous waste. The current focus is recycling and product development utilizing industrial waste as raw materials. Current research has targeted the development of high grade abrasive (Vickers hardness (VHN) > 1000 kgF/mm{sup 2}) for blasting and buffing and polishing applications. In addition to product specific physical properties, the developed formulations must also have processing characteristics necessary for vitrification using a high temperature product burner developed by Seiler Pollution Control Systems, as well as the necessary resistance to leaching of EPA regulated hazardous components. Current work has led to the development of formulations with high VHN (950 kgF/mm{sup 2}), acceptable chemical durability, and high mechanical durability utilizing electric arc furnace dust (KO61) and foundry sand as the major components.

  16. Wire blade development for Fixed Abrasive Slicing Technique (FAST) slicing

    NASA Technical Reports Server (NTRS)

    Khattak, C. P.; Schmid, F.; Smith, M. B.

    1982-01-01

    A low cost, effective slicing method is essential to make ingot technology viable for photovoltaics in terrestrial applications. The fixed abrasive slicing technique (FAST) combines the advantages of the three commercially developed techniques. In its development stage FAST demonstrated cutting effectiveness of 10 cm and 15 cm diameter workpieces. Wire blade development is still the critical element for commercialization of FAST technology. Both impregnated and electroplated wire blades have been developed; techniques have been developed to fix diamonds only in the cutting edge of the wire. Electroplated wires show the most near term promise and this approach is emphasized. With plated wires it has been possible to control the size and shape of the electroplating, it is expected that this feature reduces kerf and prolongs the life of the wirepack.

  17. Quantitative modeling of facet development in ventifacts by sand abrasion

    NASA Astrophysics Data System (ADS)

    Várkonyi, Péter L.; Laity, Julie E.; Domokos, Gábor

    2016-03-01

    We use a quantitative model to examine rock abrasion by direct impacts of sand grains. Two distinct mechanisms are uncovered (unidirectional and isotropic), which contribute to the macro-scale morphological characters (sharp edges and flat facets) of ventifacts. It is found that facet formation under conditions of a unidirectional wind relies on certain mechanical properties of the rock material, and we confirm the dominant role of this mechanism in the formation of large ventifacts. Nevertheless small ventifacts may also be shaped to polyhedral shapes in a different way (isotropic mechanism), which is not sensitive to wind characteristics nor to rock material properties. The latter mechanism leads to several 'mature' shapes, which are surprisingly analogous to the morphologies of typical small ventifacts. Our model is also able to explain certain quantitative laboratory and field observations, including quick decay of facet angles of ventifacts followed by stabilization in the range 20-30°.

  18. Cover and Erosion Asymmetry in Saltation-Abrasion

    NASA Astrophysics Data System (ADS)

    Stark, C. P.; Parker, G.

    2014-12-01

    Erosion in bedrock-floored rivers is both driven and limited by the amount of sediment transported along the bed. Some sediment boosts wear rates, whereas too much generates a protective cover. This phenomenon determines the shape of river channels in a variety of landscapes and limits how fast they evolve. Here we reevaluate data from a well-known bedrock wear experiment to throw new light on how the saltation-abrasion process. Instead of a symmetric form for erosion versus sediment flux relative to transport capacity, we find the erosion rate peak shifts towards lower sediment fluxes when blocking of oblique saltation trajectories is taken into account. The theoretical context for this reevaluation is a cover-saltation-abrasion model, based on queueing theory (QT), for bedload transport over a planar bedrock bed. The QT approach provides some clarity in the stochastic treatment of granular impacts and cover, and generates closed-form solutions for wear rate in terms of sediment flux and simplified saltation geometry. Applied to the Sklar & Dietrich (2001) experiments in a very small recirculating flume, the two-parameter QT model fits the observed relation between erosion rate and sediment load, infers sediment flux as a function of load, admits non-negligible wear rates for a mean sediment depth of one grain, i.e., for full cover on average, but also suggests that bedrock erosion is blocked at >=50% instantaneous cover. The QT model makes testable predictions for future laboratory experiments and highlights the need for specific improvements in more comprehensive treatments of bedrock erosion and cover.

  19. Scratching vulnerability of conventional vs highly cross-linked polyethylene liners because of large embedded third-body particles.

    PubMed

    Heiner, Anneliese D; Galvin, Alison L; Fisher, John; Callaghan, John J; Brown, Thomas D

    2012-05-01

    The hypothesis of this study was that acetabular liner vulnerability to scratching from femoral heads, roughened by third bodies embedded in the liner, is not significantly lower for highly cross-linked polyethylene (HXPE) than for conventional polyethylene (CPE). Six CPE and 6 HXPE acetabular liners were each reproducibly embedded with 5 cobalt-chromium-molybdenum (CoCrMo) beads then run for 10,000 cycles in a joint simulator. By visual rank ordering, there was low association between liner scratch severity and polyethylene type. The CPE and HXPE liner scratches were not significantly different in scratch peak-valley height or width or in liner roughness in the vicinity of the embedded beads. This model indicated that high cross-linking of polyethylene does not offer appreciable protection against severe scratching induced by large embedded third-body particles. PMID:22115764

  20. Prediction of scratch resistance of cobalt chromium alloy bearing surface, articulating against ultra-high molecular weight polyethylene, due to third-body wear particles.

    PubMed

    Mirghany, M; Jin, Z M

    2004-01-01

    The entrapment of abrasive particles within the articulation between a cobalt chromium alloy (CoCrMo) femoral component and an ultra-high molecular weight polyethylene (UHMWPE) cup of artificial hip joints or tibial inserts of artificial knee joints usually scratches the metallic bearing surface and consequently increases the surface roughness. This has been recognized as one of the main causes of excessive polyethylene wear, leading to osteolysis and loosening of the prosthetic components. The purpose of this study was to use the finite element method to investigate the resistance of the cobalt chromium alloy bearing surface to plastic deformation, as a first approximation to causing scratches, due to various entrapped debris such as bone, CoCrMo and ZrO2 (contained in radiopaque polymethyl methacrylate cement). A simple axisymmetric micro contact mechanics model was developed, where a spherical third-body wear particle was indented between the two bearing surfaces, modelled as two solid cylinders of a given diameter, under the contact pressure determined from macro-models representing either hip or knee implants. The deformation of both the wear particle and the bearing surfaces was modelled and was treated as elastic-plastic. The indented peak-to-valley height on the CoCrMo bearing surface from the finite element model was found to be in good agreement with that reported in a previous study when the third-body wear particle was assumed to be rigid. Under the physiological contact pressure experienced in both hip and knee implants, ZrO2 wear particles were found to be fully embedded within the UHMWPE bearing surface, and the maximum von Mises stresses within the CoCrMo bearing surface reached the corresponding yield strength. Consequently, the CoCrMo bearing surface was deformed plastically and the corresponding peak-to-valley height (surface roughness) was found to increase with both the hardness and the size of the wear particle. Even in the case of CoCrMo wear

  1. Involvement of peripheral mu opioid receptors in scratching behavior in mice.

    PubMed

    Yamamoto, Atsuki; Sugimoto, Yukio

    2010-12-15

    Pruritus is a common adverse effect of opioid treatment. However, the mechanism by which pruritus is induced by opioid administration is unclear. In this study, we examined the effects of the intradermal injection of loperamide, a peripherally restricted opioid receptor agonist, on the itch sensation. When injected intradermally into the rostral part of the back in mice, loperamide elicited scratching behavior. We also examined the effects of the selective mu opioid receptor agonist [d-Ala², N-Me-Phe⁴, Gly⁵-ol]-enkephalin acetate (DAMGO), the selective delta opioid receptor agonist [d-Pen(2,5)]-enkephalin (DPDPE), and the selective kappa opioid receptor agonist U-50488H on scratching behavior in mice in order to determine which subtype is involved in opioid-induced pruritus. Following intradermal injection into the rostral part of the back in mice, DAMGO elicited scratching behavior, while DPDPE and U-50488H did not. This suggests that peripheral mu opioid activation elicits the itch sensation. Next, we focused on the treatment of opioid-induced itch sensation without central adverse effects. Naloxone methiodide is a peripherally restricted opioid receptor antagonist. In the present study, naloxone methiodide significantly suppressed scratching behavior induced by loperamide and DAMGO. These findings suggest that mu opioid receptors play a primary role in peripheral pruritus and that naloxone methiodide may represent a possible remedy for opioid-induced itching. PMID:20863827

  2. Lactobacillus rhamnosus GG Lysate Increases Re-Epithelialization of Keratinocyte Scratch Assays by Promoting Migration

    PubMed Central

    Mohammedsaeed, Walaa; Cruickshank, Sheena; McBain, Andrew J.; O’Neill, Catherine A.

    2015-01-01

    A limited number of studies have investigated the potential of probiotics to promote wound healing in the digestive tract. The aim of the current investigation was to determine whether probiotic bacteria or their extracts could be beneficial in cutaneous wound healing. A keratinocyte monolayer scratch assay was used to assess re-epithelialization; which comprises keratinocyte proliferation and migration. Primary human keratinocyte monolayers were scratched then exposed to lysates of Lactobacillus (L) rhamnosus GG, L. reuteri, L. plantarum or L. fermentum. Re-epithelialization of treated monolayers was compared to that of untreated controls. Lysates of L. rhamnosus GG and L. reuteri significantly increased the rate of re-epithelialization, with L. rhamnosus GG being the most efficacious. L. reuteri increased keratinocyte proliferation while L. rhamnosus GG lysate significantly increased proliferation and migration. Microarray analysis of L. rhamnosus GG treated scratches showed increased expression of multiple genes including the chemokine CXCL2 and its receptor CXCR2. These are involved in normal wound healing where they stimulate keratinocyte proliferation and/or migration. Increased protein expression of both CXCL2 and CXCR2 were confirmed by ELISA and immunoblotting. These data demonstrate that L. rhamnosus GG lysate accelerates re-epithelialization of keratinocyte scratch assays, potentially via chemokine receptor pairs that induce keratinocyte migration. PMID:26537246

  3. Lactobacillus rhamnosus GG Lysate Increases Re-Epithelialization of Keratinocyte Scratch Assays by Promoting Migration.

    PubMed

    Mohammedsaeed, Walaa; Cruickshank, Sheena; McBain, Andrew J; O'Neill, Catherine A

    2015-01-01

    A limited number of studies have investigated the potential of probiotics to promote wound healing in the digestive tract. The aim of the current investigation was to determine whether probiotic bacteria or their extracts could be beneficial in cutaneous wound healing. A keratinocyte monolayer scratch assay was used to assess re-epithelialization; which comprises keratinocyte proliferation and migration. Primary human keratinocyte monolayers were scratched then exposed to lysates of Lactobacillus (L) rhamnosus GG, L. reuteri, L. plantarum or L. fermentum. Re-epithelialization of treated monolayers was compared to that of untreated controls. Lysates of L. rhamnosus GG and L. reuteri significantly increased the rate of re-epithelialization, with L. rhamnosus GG being the most efficacious. L. reuteri increased keratinocyte proliferation while L. rhamnosus GG lysate significantly increased proliferation and migration. Microarray analysis of L. rhamnosus GG treated scratches showed increased expression of multiple genes including the chemokine CXCL2 and its receptor CXCR2. These are involved in normal wound healing where they stimulate keratinocyte proliferation and/or migration. Increased protein expression of both CXCL2 and CXCR2 were confirmed by ELISA and immunoblotting. These data demonstrate that L. rhamnosus GG lysate accelerates re-epithelialization of keratinocyte scratch assays, potentially via chemokine receptor pairs that induce keratinocyte migration. PMID:26537246

  4. Streptobacillus moniliformis as the causative agent in spondylodiscitis and psoas abscess after rooster scratches.

    PubMed

    Dubois, Damien; Robin, Frédéric; Bouvier, Damien; Delmas, Julien; Bonnet, Richard; Lesens, Olivier; Hennequin, Claire

    2008-08-01

    We report a case of Streptobacillus moniliformis spondylodiscitis accompanied by a psoas abscess in an 80-year-old man scratched by a rooster. S. moniliformis was identified from abscess fluid by use of 16S rRNA gene sequencing. After 18 weeks of antimicrobial therapy, the clinical condition of the patient improved. PMID:18562588

  5. Dragonfly: strengthening programming skills by building a game engine from scratch

    NASA Astrophysics Data System (ADS)

    Claypool, Mark

    2013-06-01

    Computer game development has been shown to be an effective hook for motivating students to learn both introductory and advanced computer science topics. While games can be made from scratch, to simplify the programming required game development often uses game engines that handle complicated or frequently used components of the game. These game engines present the opportunity to strengthen programming skills and expose students to a range of fundamental computer science topics. While educational efforts have been effective in using game engines to improve computer science education, there have been no published papers describing and evaluating students building a game engine from scratch as part of their course work. This paper presents the Dragonfly-approach in which students build a fully functional game engine from scratch and make a game using their engine as part of a junior-level course. Details on the programming projects are presented, as well as an evaluation of the results from two offerings that used Dragonfly. Student performance on the projects as well as student assessments demonstrates the efficacy of having students build a game engine from scratch in strengthening their programming skills.

  6. Quantitative characterization of agglomerate abrasion in a tumbling blender by using the Stokes number approach.

    PubMed

    Willemsz, Tofan A; Nguyen, Tien Thanh; Hooijmaijers, Ricardo; Frijlink, Henderik W; Vromans, Herman; van der Voort Maarschalk, Kees

    2013-03-01

    Removal of microcrystalline cellulose agglomerates in a dry-mixing system (lactose, 100 M) predominantly occurs via abrasion. The agglomerate abrasion rate potential is estimated by the Stokes abrasion (StAbr) number of the system. The StAbr number equals the ratio between the kinetic energy density of the moving powder bed and the work of fracture of the agglomerate. Basically, the StAbr number concept describes the blending condition of the dry-mixing system. The concept has been applied to investigate the relevance of process parameters on agglomerate abrasion in tumbling blenders. Here, process parameters such as blender rotational speed and relative fill volumes were investigated. In this study, the StAbr approach revealed a transition point between abrasion rate behaviors. Below this transition point, a blending condition exists where agglomerate abrasion is dominated by the kinetic energy density of the powder blend. Above this transition point, a blending condition exists where agglomerates show (undesirable) slow abrasion rates. In this situation, the blending condition is mainly determined by the high fill volume of the filler. PMID:23250711

  7. A Novel Nude Mouse Model of Hypertrophic Scarring Using Scratched Full Thickness Human Skin Grafts

    PubMed Central

    Alrobaiea, Saad M.; Ding, Jie; Ma, Zengshuan; Tredget, Edward E.

    2016-01-01

    Objective: Hypertrophic scar (HTS) is a dermal form of fibroproliferative disorder that develops following deep skin injury. HTS can cause deformities, functional disabilities, and aesthetic disfigurements. The pathophysiology of HTS is not understood due to, in part, the lack of an ideal animal model. We hypothesize that human skin with deep dermal wounds grafted onto athymic nude mice will develop a scar similar to HTS. Our aim is to develop a representative animal model of human HTS. Approach: Thirty-six nude mice were grafted with full thickness human skin with deep dermal scratch wound before or 2 weeks after grafting or without scratch. The scratch on the human skin grafts was made using a specially designed jig that creates a wound >0.6 mm in depth. The xenografts were morphologically analyzed by digital photography. Mice were euthanized at 1, 2, and 3 months postoperatively for histology and immunohistochemistry analysis. Results: The mice developed raised and firm scars in the scratched xenografts with more contraction, increased infiltration of macrophage, and myofibroblasts compared to the xenografts without deep dermal scratch wound. Scar thickness and collagen bundle orientation and morphology resembled HTS. The fibrotic scars in the wounded human skin were morphologically and histologically similar to HTS, and human skin epithelial cells persisted in the remodeling tissues for 1 year postengraftment. Innovation and Conclusions: Deep dermal injury in human skin retains its profibrotic nature after transplantation, affording a novel model for the assessment of therapies for the treatment of human fibroproliferative disorders of the skin. PMID:27366591

  8. How have wear testing and joint simulator studies helped to discriminate among materials and designs?

    PubMed

    McKellop, Harry A; D'Lima, Darryl

    2008-01-01

    Historically, hip joint simulators most often have been used to model wear of a bearing surface against a bearing surface. These simulators have provided highly accurate predictions of the in vivo wear of a broad spectrum of bearing materials, including cross-linked polyethylenes, metal-on-metal, ceramic-on-ceramic, and others in development. In recent years, more severe conditions have been successfully modeled, including jogging, stair climbing, ball-cup micro separation, third-body abrasion, and neck-socket impingement. These tests have served to identify improved materials and to eliminate some with inadequate wear resistance prior to their clinical use. Simulation of the knee joint is inherently more complex than it is for the hip. It is more difficult to compare the results of laboratory tests with actual clinical performance, due to the lack of accurate in vivo measures of wear. Nevertheless, knee simulators, based on force control or motion control, have successfully reproduced the type of surface damage that occurs in vivo (eg, burnishing, scratching, pitting) as well as the size and shapes of the resultant wear particles. Knee simulators have been used to compare molded versus machined polyethylene components, highly cross-linked polyethylenes, fixed versus mobile bearings, and oxidized zirconia and other materials, under optimal conditions as well as more severe wear modes, such as malalignment, higher loading and activity levels, and third-body roughening. PMID:18612005

  9. Optical-model abrasion cross sections for high-energy heavy ions

    NASA Technical Reports Server (NTRS)

    Townsend, L. W.

    1981-01-01

    Within the context of eikonal scattering theory, a generalized optical model potential approximation to the nucleus-nucleus multiple scattering series is used in an abrasion-ablation collision model to predict abrasion cross sections for relativistic projectile heavy ions. Unlike the optical limit of Glauber theory, which cannot be used for very light nuclei, the abrasion formalism is valid for any projectile target combination at any incident kinetic energy for which eikonal scattering theory can be utilized. Results are compared with experimental results and predictions from Glauber theory.

  10. Optical-model abrasion cross sections for high-energy heavy ions

    SciTech Connect

    Townsend, L.W.

    1981-07-01

    Within the context of eikonal scattering theory, a generalized optical model potential approximation to the nucleus-nucleus multiple scattering series is used in an abrasion-ablation collision model to predict abrasion cross sections for relativistic projectile heavy ions. Unlike the optical limit of Glauber theory, which cannot be used for very light nuclei, the abrasion formalism is valid for any projectile target combination at any incident kinetic energy for which eikonal scattering theory can be utilized. Results are compared with experimental results and predictions from Glauber theory.

  11. High Resolution Laser Scanning Techniques for Rock Abrasion and Texture Analyses on Mars and Earth

    NASA Technical Reports Server (NTRS)

    Bridges, N. T.; Razdan, A.; Greeley, R.; Laity, J. E.

    2004-01-01

    Aeolian abrasion is operative in many arid locations on Earth and is probably the dominant rock erosion process in the current Martian environment. Therefore, understanding the controlling parameters and rates of aeolian abrasion provides 1) insight into the stability of rocks on planetary surfaces and the environments under which the rocks abrade, and 2) a link between ventifact (a rock abraded by windblown particles) morphology and: a) abrasion conditions, b) possible ancient environments under which the rocks were abraded, and c) rock properties. promising and we plan further investigations in the wind tunnel and field. Our intent here is to discuss the basic technique, initial results, and upcoming plans.

  12. Target correlation effects on neutron-nucleus total, absorption, and abrasion cross sections

    NASA Technical Reports Server (NTRS)

    Cucinotta, Francis A.; Townsend, Lawrence W.; Wilson, John W.

    1991-01-01

    Second order optical model solutions to the elastic scattering amplitude were used to evaluate total, absorption, and abrasion cross sections for neutron nucleus scattering. Improved agreement with experimental data for total and absorption cross sections is found when compared with first order (coherent approximation) solutions, especially below several hundred MeV. At higher energies, the first and second order solutions are similar. There are also large differences in abrasion cross section calculations; these differences indicate a crucial role for cluster knockout in the abrasion step.

  13. Abrasion of heavy-duty coated steel pipes by sediment transport

    SciTech Connect

    Kariyazono, Yoshihisa; Miyajima, Yoshihiro; Sato, Koichi; Yamashita, Toshihiko, Yamashita; Saeki, Hiroshi

    1994-12-31

    Heavy-duty coatings are standard treatment for steel pipe piles in coastal zones to prevent corrosion. Large amounts of sand sometimes drift around piles by the action of waves. Coatings undergo abrasion by collision of sand particles. Authors carried out experiments by a large scale U-shaped tube which generated a strong oscillatory flow with sand drift and numerical analysis of collision of the particles. Authors found out the abrasion rate of pile is nearly proportional to the collision energy of the particles. Abrasion rate of polyethylene and elastic polyurethane coatings were lower than those of other materials.

  14. Surface assessment and modification of concrete using abrasive blasting

    NASA Astrophysics Data System (ADS)

    Millman, Lauren R.

    Composite systems are applied to concrete substrates to strengthen and extend the service life. Successful restoration or rehabilitation requires surface preparation prior to the application of the overlay. Surface coatings, waterproofing systems, and other external surface applications also require surface preparation prior to application. Abrasive blast media is often used to clean and uniformly roughen the substrate. The appropriate surface roughness is necessary to facilitate a strong bond between the existing substrate and overlay. Thus, surface modification using abrasive blast media (sand and dry ice), their respective environmental effects, surface roughness characterization prior to and after blasting, and the adhesion between the substrate and overlay are the focus of this dissertation. This dissertation is comprised of an introduction, a literature review, and four chapters, the first of which addresses the environmental effects due to abrasive blasting using sand, water, and dry ice. The assessment considered four response variables: carbon dioxide (CO2) emissions, fuel and energy consumption, and project duration. The results indicated that for sand blasting and water jetting, the primary factor contributing to environmental detriment was CO22 emissions from vehicular traffic near the construction site. The second chapter is an analysis of the International Concrete Repair Institute's (ICRI) concrete surface profiles (CSPs) using 3-D optical profilometry. The primary objective was to evaluate the suitability of approximating the 3-D surface (areal) parameters with those extracted from 2-D (linear) profiles. Four profile directions were considered: two diagonals, and lines parallel and transverse to the longitudinal direction of the mold. For any CSP mold, the estimation of the 3-D surface roughness using a 2-D linear profile resulted in underestimation and overestimation errors exceeding 50%, demonstrating the inadequacy of 2-D linear profiles to

  15. Thermocycling--the effects upon the compressive strength and abrasion resistance of three composite resins.

    PubMed

    Chadwick, R G

    1994-09-01

    The purpose of this investigation was to examine the effects of thermocycling upon the compressive strength and abrasive wear resistance of three commercial composites Fulfil, P-50 and Herculite-XR. Specimens of each material were divided into five treatment groups comprising a control, and four different cycling and storage regimes. Tests for compressive strength and wear resistance were carried out. Prior to testing all specimens were stored in distilled water for 1 week. Three groups were stored at a temperature of 37 degrees C and the remaining two at 60 degrees C. Thereafter all groups that were thermocycled were subjected to 750 cycles of a thermocycling regime consisting of the cycle ACAB where A and B represent the fixed temperatures of 37 degrees C and 5 degrees C, and C, depending upon the treatment group, either 50 degrees C or 60 degrees C. One-way analyses of variance upon the compressive strength and wear factor data following the treatments highlighted significant differences in the mean compressive strength for all materials (Fulfil (P < 0.05), P-50 and Herculite-XR (P < 0.01)) and in the wear factor values for only Fulfil and P-50 (P < 0.001). Surprisingly, thermocycling P-50 with an upper temperature limit of 50 degrees C had catastrophic consequences upon the measured properties. It is concluded that some of the observed behaviour may have potentially detrimental consequences upon the long-term clinical durability of the materials tested. PMID:7996337

  16. Effect of Air Abrasion Preconditioning on Microleakage in Class V Restorations Under Cyclic Loading: An In-vitro Study

    PubMed Central

    Dharmani, Charan Kamal Kaur; Singh, Shamsher; Logani, Ajay; Shah, Naseem

    2014-01-01

    Background: Microleakage in class V Glass Ionomer Cement(GIC) or composite restorations at enamel or cementum margins has been cited as a reason for their failure. Air abrasion has been used to precondition tooth surface for increasing retention of such restorations. This study is done to evaluate the effect of preconditioning with air abrasion on microleakage in class V GIC and composite restorations. Materials and Methods: Class V cavities were prepared in 40 freshly extracted teeth. They were categorised into following four groups (n=10) depending on cavity preconditioning and restoration. Group I: 10% polyacrylic acid and GI (Ketac molar TM 3M ESPE); Group II: AA and GI; Group III: 35% Phosphoric acid and micro filled composite (MC) (Heliomolar, Ivoclar Vivadent); Group IV: AA and MC. Each group was further divided into subgroups A (no loading) & B (cyclic loading). Microleakage at occlusal and gingival margins was evaluated using methylene blue dye penetration method. Statistical analysis was done using Kruskal-wallis test and Mann-Whitney U test. Results: Microleakage at cementum margins was higher than at enamel margins in all the groups. Preconditioning with AA resulted in increased micro leakage. Conclusion: AA as a preconditioning agent was ineffective in producing superior tooth-restoration bonding. PMID:24995240

  17. Abrasive jet micro-machining of polymeric materials

    NASA Astrophysics Data System (ADS)

    Hailu, Getu

    In the abrasive jet micro-machining (AJM) process, a jet of small particles is directed through an erosion resistant mask opening so that micro-sized features (i.e., micro-channels, holes, etc.) can be machined for the fabrication of micro-devices such as micro-fluidic and micro-electro-mechanical-systems (MEMS). Polymeric materials and elastomers have found applications in a wide variety of micro-devices. This thesis investigates the AJM of such materials, addressing the major challenges that must be overcome in order for the process to gain wider acceptance in industry. The thesis first presents a novel cryogenically assisted abrasive jet micro-machining (CAJM) technique that enables the micro-machining of elastomers such as polydimethylsiloxane (PDMS) that cannot be machined at room temperature. It was found that the erosion rate during CAJM is greatly increased, and the degree of particle embedment greatly decreased, compared to room temperature experiments. A finite element (FE) analysis was used to investigate the relationships between erosion, the heat transfer of the cooling jet and the resulting target temperature during the CAJM of channels in PDMS. The analysis illustrated the asymmetric nature of the cooling with much more cooling occurring towards the trailing edge of the jet. It was found that the predicted shape of the evolving machined surface profiles was improved significantly when a FE model was used to account for thermal distortion occurring during the CAJM process. An unwanted consequence of the AJM of polymeric materials was found to be particle embedding. Criteria leading to the embedding of spherical and angular particles in such materials were identified and modelled using rigid plastic analyses. It was found that the likelihood of embedding was proportional to the static coefficient of friction between the particle and the target for angular particles, and the depth of penetration for spherical particles. Scanning electron microscopy with

  18. [Acute total knee replacement infection after a cat bite and scratch: a clinical case and review of the literature].

    PubMed

    Miranda, I; Angulo, M; Amaya, J V

    2013-01-01

    In the last 15 years only few cases of Pasteurella multocida (P. multocida) total knee arthroplasty infection have been published, mostly related to cat or dog bites or scratches. We report a case of P. multocida total knee arthroplasty infection in a 64-year- old patient, 10 days after being scratched and bitten by his cat. The patient was successfully treated with debridement and tibial interspacer exchange and antibiotic treatment for 6 weeks. Antimicrobial prophylaxis should be considered in cat or dog bites or scratches victims with prosthetic joints. PMID:23885657

  19. Dental Abrasion of Incisor caused by a Babies' Dummy Clip: A Case Report.

    PubMed

    Doğramacı, Esma J; Rossi-Fedele, Giampiero

    2015-09-01

    Tooth surface loss (TSL), the non-carious loss of tooth tissue, is considered pathological if the teeth involved experience sensitivity and pain, are functionally compromised or they detract from the patient's appearance. TSL is a common clinical finding in many patient groups, although differences between the primary and permanent dentition contribute to TSL occurring at a faster rate and with worse outcomes in the primary dentition. This case report presents localized abrasion and associated apical periodontitis affecting a single primary tooth in a 2-year-old infant following the misuse of a babies' dummy clip whilst teething. Abrasion is rare in the primary dentition. CPD/CLINICAL RELEVANCE: This article highlights an unusual presentation of dental abrasion affecting the primary dentition caused by a previously unreported foreign object; abrasion in this case was a side-effect of soothing the discomfort of teething. PMID:26630866

  20. Demonstration experience with an abrasive blasting technique for decontaminating concrete pads

    SciTech Connect

    Devgun, J.S. ); Land, R.R. ); Doane, R.W. )

    1990-01-01

    A demonstration was performed for decontaminating a radioactivity contaminated concrete pad with a portable abrasive blasting system. The system utilizes a rotating blast wheel that scours the concrete surface with metal abrasive. The metal abrasive, pulverized concrete dust, and contaminants rebound into a separator chamber. The reusable metal abrasive is recycled, and the pulverized media are removed to an integral dust collection system. The exhaust is HEPA filtered to minimize release of airborne contaminants. However, the technique had limited success in reducing contamination around the cracks and seams in the concrete where the higher activity levels of contamination were detected during the radiological survey before the cleanup. The technique can be successful and cost-effective in decontaminating large areas of low contamination; however, careful characterization and planning are necessary. 3 refs., 3 figs., 1 tabs.