Science.gov

Sample records for absolute frequency determination

  1. Real-Time Determination of Absolute Frequency in Continuous-Wave Terahertz Radiation with a Photocarrier Terahertz Frequency Comb Induced by an Unstabilized Femtosecond Laser

    NASA Astrophysics Data System (ADS)

    Minamikawa, Takeo; Hayashi, Kenta; Mizuguchi, Tatsuya; Hsieh, Yi-Da; Abdelsalam, Dahi Ghareab; Mizutani, Yasuhiro; Yamamoto, Hirotsugu; Iwata, Tetsuo; Yasui, Takeshi

    2016-05-01

    A practical method for the absolute frequency measurement of continuous-wave terahertz (CW-THz) radiation uses a photocarrier terahertz frequency comb (PC-THz comb) because of its ability to realize real-time, precise measurement without the need for cryogenic cooling. However, the requirement for precise stabilization of the repetition frequency ( f rep) and/or use of dual femtosecond lasers hinders its practical use. In this article, based on the fact that an equal interval between PC-THz comb modes is always maintained regardless of the fluctuation in f rep, the PC-THz comb induced by an unstabilized laser was used to determine the absolute frequency f THz of CW-THz radiation. Using an f rep-free-running PC-THz comb, the f THz of the frequency-fixed or frequency-fluctuated active frequency multiplier chain CW-THz source was determined at a measurement rate of 10 Hz with a relative accuracy of 8.2 × 10-13 and a relative precision of 8.8 × 10-12 to a rubidium frequency standard. Furthermore, f THz was correctly determined even when fluctuating over a range of 20 GHz. The proposed method enables the use of any commercial femtosecond laser for the absolute frequency measurement of CW-THz radiation.

  2. Molecular iodine absolute frequencies. Final report

    SciTech Connect

    Sansonetti, C.J.

    1990-06-25

    Fifty specified lines of {sup 127}I{sub 2} were studied by Doppler-free frequency modulation spectroscopy. For each line the classification of the molecular transition was determined, hyperfine components were identified, and one well-resolved component was selected for precise determination of its absolute frequency. In 3 cases, a nearby alternate line was selected for measurement because no well-resolved component was found for the specified line. Absolute frequency determinations were made with an estimated uncertainty of 1.1 MHz by locking a dye laser to the selected hyperfine component and measuring its wave number with a high-precision Fabry-Perot wavemeter. For each line results of the absolute measurement, the line classification, and a Doppler-free spectrum are given.

  3. Monolithically integrated absolute frequency comb laser system

    DOEpatents

    Wanke, Michael C.

    2016-07-12

    Rather than down-convert optical frequencies, a QCL laser system directly generates a THz frequency comb in a compact monolithically integrated chip that can be locked to an absolute frequency without the need of a frequency-comb synthesizer. The monolithic, absolute frequency comb can provide a THz frequency reference and tool for high-resolution broad band spectroscopy.

  4. Accurate absolute frequencies of the {nu}{sub 1}+{nu}{sub 3} band of {sup 13}C{sub 2}H{sub 2} determined using an infrared mode-locked Cr:YAG laser frequency comb

    SciTech Connect

    Madej, Alan A.; Bernard, John E.; John Alcock, A.; Czajkowski, Andrzej; Chepurov, Sergei

    2006-04-15

    Absolute frequency measurements, with up to 1x10{sup -11} level accuracies, are presented for 60 lines of the P and R branches for the {nu}{sub 1}+{nu}{sub 3} band of {sup 13}C{sub 2}H{sub 2} at 1.5 {mu}m (194 THz). The measurements were made using cavity-enhanced, diode-laser-based saturation spectroscopy. With one laser system stabilized to the P(16) line and a second laser system stabilized to the line whose frequency was to be determined, a Cr:YAG frequency comb was employed to accurately measure the tetrahertz level frequency intervals. The results are compared with recent work from other groups and indicate that these lines would form a basis for a high-quality atlas of reference frequencies for this region of the spectrum.

  5. Accurate absolute reference frequencies from 1511 to 1545 nm of the {nu}{sub 1}+{nu}{sub 3} band of {sup 12}C{sub 2}H{sub 2} determined with laser frequency comb interval measurements

    SciTech Connect

    Madej, Alan A.; Alcock, A. John; Czajkowski, Andrzej; Bernard, John E.; Chepurov, Sergei

    2006-10-15

    Absolute frequency measurements, with uncertainties as low as 2 kHz (1x10{sup -11}), are presented for the {nu}{sub 1}+{nu}{sub 3} band of {sup 12}C{sub 2}H{sub 2} at 1.5 {mu}m (194-198 THz). The measurements were made using cavity-enhanced, diode-laser-based saturation spectroscopy. With one laser system stabilized to the P(16) line of {sup 13}C{sub 2}H{sub 2} and a system stabilized to the line in {sup 12}C{sub 2}H{sub 2} whose frequency was to be determined, a Cr:YAG laser-based frequency comb was employed to measure the frequency intervals. The systematic uncertainty is notably reduced relative to that of previous studies, and the region of measured lines has been extended. Improved molecular constants are obtained.

  6. Absolute determination of local tropospheric OH concentrations

    NASA Technical Reports Server (NTRS)

    Armerding, Wolfgang; Comes, Franz-Josef

    1994-01-01

    Long path absorption (LPA) according to Lambert Beer's law is a method to determine absolute concentrations of trace gases such as tropospheric OH. We have developed a LPA instrument which is based on a rapid tuning of the light source which is a frequency doubled dye laser. The laser is tuned across two or three OH absorption features around 308 nm with a scanning speed of 0.07 cm(exp -1)/microsecond and a repetition rate of 1.3 kHz. This high scanning speed greatly reduces the fluctuation of the light intensity caused by the atmosphere. To obtain the required high sensitivity the laser output power is additionally made constant and stabilized by an electro-optical modulator. The present sensitivity is of the order of a few times 10(exp 5) OH per cm(exp 3) for an acquisition time of a minute and an absorption path length of only 1200 meters so that a folding of the optical path in a multireflection cell was possible leading to a lateral dimension of the cell of a few meters. This allows local measurements to be made. Tropospheric measurements have been carried out in 1991 resulting in the determination of OH diurnal variation at specific days in late summer. Comparison with model calculations have been made. Interferences are mainly due to SO2 absorption. The problem of OH self generation in the multireflection cell is of minor extent. This could be shown by using different experimental methods. The minimum-maximum signal to noise ratio is about 8 x 10(exp -4) for a single scan. Due to the small size of the absorption cell the realization of an open air laboratory is possible in which by use of an additional UV light source or by additional fluxes of trace gases the chemistry can be changed under controlled conditions allowing kinetic studies of tropospheric photochemistry to be made in open air.

  7. Multifrequency continuous wave terahertz spectroscopy for absolute thickness determination

    SciTech Connect

    Scheller, Maik; Baaske, Kai; Koch, Martin

    2010-04-12

    We present a tunable multifrequency continuous wave terahertz spectrometer based on two laser diodes, photoconductive antennas, and a coherent detection scheme. The system is employed to determine the absolute thickness of samples utilizing a proposed synthetic difference frequency method to circumvent the 2pi uncertainty known from conventional photomixing systems while preserving a high spatial resolution.

  8. Determination of the absolute contours of optical flats

    NASA Technical Reports Server (NTRS)

    Primak, W.

    1969-01-01

    Emersons procedure is used to determine true absolute contours of optical flats. Absolute contours of standard flats are determined and a comparison is then made between standard and unknown flats. Contour differences are determined by deviation of Fizeau fringe.

  9. MAGSAT: Vector magnetometer absolute sensor alignment determination

    NASA Technical Reports Server (NTRS)

    Acuna, M. H.

    1981-01-01

    A procedure is described for accurately determining the absolute alignment of the magnetic axes of a triaxial magnetometer sensor with respect to an external, fixed, reference coordinate system. The method does not require that the magnetic field vector orientation, as generated by a triaxial calibration coil system, be known to better than a few degrees from its true position, and minimizes the number of positions through which a sensor assembly must be rotated to obtain a solution. Computer simulations show that accuracies of better than 0.4 seconds of arc can be achieved under typical test conditions associated with existing magnetic test facilities. The basic approach is similar in nature to that presented by McPherron and Snare (1978) except that only three sensor positions are required and the system of equations to be solved is considerably simplified. Applications of the method to the case of the MAGSAT Vector Magnetometer are presented and the problems encountered discussed.

  10. The absolute frequency of the 87Sr optical clock transition

    NASA Astrophysics Data System (ADS)

    Campbell, Gretchen K.; Ludlow, Andrew D.; Blatt, Sebastian; Thomsen, Jan W.; Martin, Michael J.; de Miranda, Marcio H. G.; Zelevinsky, Tanya; Boyd, Martin M.; Ye, Jun; Diddams, Scott A.; Heavner, Thomas P.; Parker, Thomas E.; Jefferts, Steven R.

    2008-10-01

    The absolute frequency of the 1S0-3P0 clock transition of 87Sr has been measured to be 429 228 004 229 873.65 (37) Hz using lattice-confined atoms, where the fractional uncertainty of 8.6 × 10-16 represents one of the most accurate measurements of an atomic transition frequency to date. After a detailed study of systematic effects, which reduced the total systematic uncertainty of the Sr lattice clock to 1.5 × 10-16, the clock frequency is measured against a hydrogen maser which is simultaneously calibrated to the US primary frequency standard, the NIST Cs fountain clock, NIST-F1. The comparison is made possible using a femtosecond laser based optical frequency comb to phase coherently connect the optical and microwave spectral regions and by a 3.5 km fibre transfer scheme to compare the remotely located clock signals.

  11. Absolute frequency of an atomic hydrogen maser clock

    NASA Technical Reports Server (NTRS)

    Peters, H. E.; Hall, R. G.; Percival, D. B.

    1972-01-01

    An accurate determination was made of the unperturbed atomic hydrogen ground state hyperfine transition frequency (F=1,m=0 - F=0,m=0) in reference to present world wide realizations of internationally defined time interval. In relation to the international atomic time system, the composite value is 1,420,405,751.7755 plus or minus 0.0031 HZ.

  12. Improved Absolute Frequency Measurement of the 171Yb Optical Lattice Clock towards a Candidate for the Redefinition of the Second

    NASA Astrophysics Data System (ADS)

    Yasuda, Masami; Inaba, Hajime; Kohno, Takuya; Tanabe, Takehiko; Nakajima, Yoshiaki; Hosaka, Kazumoto; Akamatsu, Daisuke; Onae, Atsushi; Suzuyama, Tomonari; Amemiya, Masaki; Hong, Feng-Lei

    2012-10-01

    We demonstrate an improved absolute frequency measurement of the 1S0–3P0 clock transition at 578 nm in 171Yb atoms in a one-dimensional optical lattice. The clock laser linewidth is reduced to ≈2 Hz by phase-locking the laser to an ultrastable neodymium-doped yttrium aluminum garnet (Nd:YAG) laser at 1064 nm through an optical frequency comb with an intracavity electrooptic modulator to achieve a high servo bandwidth. The absolute frequency is determined as 518 295 836 590 863.1(2.0) Hz relative to the SI second, and will be reported to the International Committee for Weights and Measures.

  13. Non-Invasive Method of Determining Absolute Intracranial Pressure

    NASA Technical Reports Server (NTRS)

    Yost, William T. (Inventor); Cantrell, John H., Jr. (Inventor); Hargens, Alan E. (Inventor)

    2004-01-01

    A method is presented for determining absolute intracranial pressure (ICP) in a patient. Skull expansion is monitored while changes in ICP are induced. The patient's blood pressure is measured when skull expansion is approximately zero. The measured blood pressure is indicative of a reference ICP value. Subsequently, the method causes a known change in ICP and measured the change in skull expansion associated therewith. The absolute ICP is a function of the reference ICP value, the known change in ICP and its associated change in skull expansion; and a measured change in skull expansion.

  14. Femtosecond frequency comb measurement of absolute frequencies and hyperfine coupling constants in cesium vapor

    SciTech Connect

    Stalnaker, Jason E.; Mbele, Vela; Gerginov, Vladislav; Fortier, Tara M.; Diddams, Scott A.; Hollberg, Leo; Tanner, Carol E.

    2010-04-15

    We report measurements of absolute transition frequencies and hyperfine coupling constants for the 8S{sub 1/2}, 9S{sub 1/2}, 7D{sub 3/2}, and 7D{sub 5/2} states in {sup 133}Cs vapor. The stepwise excitation through either the 6P{sub 1/2} or 6P{sub 3/2} intermediate state is performed directly with broadband laser light from a stabilized femtosecond laser optical-frequency comb. The laser beam is split, counterpropagated, and focused into a room-temperature Cs vapor cell. The repetition rate of the frequency comb is scanned and we detect the fluorescence on the 7P{sub 1/2,3/2{yields}}6S{sub 1/2} branches of the decay of the excited states. The excitations to the different states are isolated by the introduction of narrow-bandwidth interference filters in the laser beam paths. Using a nonlinear least-squares method we find measurements of transition frequencies and hyperfine coupling constants that are in agreement with other recent measurements for the 8S state and provide improvement by 2 orders of magnitude over previously published results for the 9S and 7D states.

  15. Determination of absolute internal conversion coefficients using the SAGE spectrometer

    NASA Astrophysics Data System (ADS)

    Sorri, J.; Greenlees, P. T.; Papadakis, P.; Konki, J.; Cox, D. M.; Auranen, K.; Partanen, J.; Sandzelius, M.; Pakarinen, J.; Rahkila, P.; Uusitalo, J.; Herzberg, R.-D.; Smallcombe, J.; Davies, P. J.; Barton, C. J.; Jenkins, D. G.

    2016-03-01

    A non-reference based method to determine internal conversion coefficients using the SAGE spectrometer is carried out for transitions in the nuclei of 154Sm, 152Sm and 166Yb. The Normalised-Peak-to-Gamma method is in general an efficient tool to extract internal conversion coefficients. However, in many cases the required well-known reference transitions are not available. The data analysis steps required to determine absolute internal conversion coefficients with the SAGE spectrometer are presented. In addition, several background suppression methods are introduced and an example of how ancillary detectors can be used to select specific reaction products is given. The results obtained for ground-state band E2 transitions show that the absolute internal conversion coefficients can be extracted using the methods described with a reasonable accuracy. In some cases of less intense transitions only an upper limit for the internal conversion coefficient could be given.

  16. Engine performance and the determination of absolute ceiling

    NASA Technical Reports Server (NTRS)

    Diehl, Walter S

    1924-01-01

    This report contains a brief study of the variation of engine power with temperature and pressure. The variation of propeller efficiency in standard atmosphere is obtained from the general efficiency curve which is developed in NACA report no. 168. The variation of both power available and power required are then determined and curves plotted, so that the absolute ceiling may be read directly from any known sea-level value of the ratio of power available to power required.

  17. Determination of absolute structure using Bayesian statistics on Bijvoet differences

    PubMed Central

    Hooft, Rob W. W.; Straver, Leo H.; Spek, Anthony L.

    2008-01-01

    A new probabilistic approach is introduced for the determination of the absolute structure of a compound which is known to be enantiopure based on Bijvoet-pair intensity differences. The new method provides relative probabilities for different models of the chiral composition of the structure. The outcome of this type of analysis can also be cast in the form of a new value, along with associated standard uncertainty, that resembles the value of the well known Flack x parameter. The standard uncertainty we obtain is often about half of the standard uncertainty in the value of the Flack x parameter. The proposed formalism is suited in particular to absolute configuration determination from diffraction data of biologically active (pharmaceutical) compounds where the strongest resonant scattering signal often comes from oxygen. It is shown that a reliable absolute configuration assignment in such cases can be made on the basis of Cu Kα data, and in some cases even with carefully measured Mo Kα data. PMID:19461838

  18. The correction of vibration in frequency scanning interferometry based absolute distance measurement system for dynamic measurements

    NASA Astrophysics Data System (ADS)

    Lu, Cheng; Liu, Guodong; Liu, Bingguo; Chen, Fengdong; Zhuang, Zhitao; Xu, Xinke; Gan, Yu

    2015-10-01

    Absolute distance measurement systems are of significant interest in the field of metrology, which could improve the manufacturing efficiency and accuracy of large assemblies in fields such as aircraft construction, automotive engineering, and the production of modern windmill blades. Frequency scanning interferometry demonstrates noticeable advantages as an absolute distance measurement system which has a high precision and doesn't depend on a cooperative target. In this paper , the influence of inevitable vibration in the frequency scanning interferometry based absolute distance measurement system is analyzed. The distance spectrum is broadened as the existence of Doppler effect caused by vibration, which will bring in a measurement error more than 103 times bigger than the changes of optical path difference. In order to decrease the influence of vibration, the changes of the optical path difference are monitored by a frequency stabilized laser, which runs parallel to the frequency scanning interferometry. The experiment has verified the effectiveness of this method.

  19. Frequency-scanning interferometry for dynamic absolute distance measurement using Kalman filter.

    PubMed

    Tao, Long; Liu, Zhigang; Zhang, Weibo; Zhou, Yangli

    2014-12-15

    We propose a frequency-scanning interferometry using the Kalman filtering technique for dynamic absolute distance measurement. Frequency-scanning interferometry only uses a single tunable laser driven by a triangle waveform signal for forward and backward optical frequency scanning. The absolute distance and moving speed of a target can be estimated by the present input measurement of frequency-scanning interferometry and the previously calculated state based on the Kalman filter algorithm. This method not only compensates for movement errors in conventional frequency-scanning interferometry, but also achieves high-precision and low-complexity dynamic measurements. Experimental results of dynamic measurements under static state, vibration and one-dimensional movement are presented. PMID:25503050

  20. Absolute determination of inelastic mean-free paths and surface excitation parameters by absolute reflection electron energy loss spectrum analysis

    NASA Astrophysics Data System (ADS)

    Nagatomi, T.; Goto, K.

    2005-11-01

    An analytical approach was proposed for simultaneously determining an inelastic mean-free path (IMFP) and a surface excitation parameter (SEP) with absolute units by the analysis of an absolute experimental reflection electron energy loss spectrum. The IMFPs and SEPs in Ni were deduced for electrons of 300 to 3000 eV. The obtained IMFPs were in good agreement with those calculated using the TPP-2M equation. The Chen-type empirical formula was proposed for determining the SEP. The results confirmed the applicability of the present approach for determining the IMFP and SEP for medium-energy electrons.

  1. Quantifying discipline practices using absolute versus relative frequencies: clinical and research implications for child welfare.

    PubMed

    Lindhiem, Oliver; Shaffer, Anne; Kolko, David J

    2014-01-01

    In the parent intervention outcome literatures, discipline practices are generally quantified as absolute frequencies or, less commonly, as relative frequencies. These differences in methodology warrant direct comparison as they have critical implications for study results and conclusions among treatments targeted at reducing parental aggression and harsh discipline. In this study, we directly compared the absolute frequency method and the relative frequency method for quantifying physically aggressive, psychologically aggressive, and nonaggressive discipline practices. Longitudinal data over a 3-year period came from an existing data set of a clinical trial examining the effectiveness of a psychosocial treatment in reducing parental physical and psychological aggression and improving child behavior (N = 139). Discipline practices (aggressive and nonaggressive) were assessed using the Conflict Tactics Scale. The two methods yielded different patterns of results, particularly for nonaggressive discipline strategies. We suggest that each method makes its own unique contribution to a more complete understanding of the association between parental aggression and intervention effects. PMID:24106146

  2. Absolute frequency measurement at 10-16 level based on the international atomic time

    NASA Astrophysics Data System (ADS)

    Hachisu, H.; Fujieda, M.; Kumagai, M.; Ido, T.

    2016-06-01

    Referring to International Atomic Time (TAI), we measured the absolute frequency of the 87Sr lattice clock with its uncertainty of 1.1 x 10-15. Unless an optical clock is continuously operated for the five days of the TAI grid, it is required to evaluate dead time uncertainty in order to use the available five-day average of the local frequency reference. We homogeneously distributed intermittent measurements over the five-day grid of TAI, by which the dead time uncertainty was reduced to low 10-16 level. Three campaigns of the five (or four)-day consecutive measurements have resulted in the absolute frequency of the 87Sr clock transition of 429 228 004 229 872.85 (47) Hz, where the systematic uncertainty of the 87Sr optical frequency standard amounts to 8.6 x 10-17.

  3. Absolute frequency measurements and hyperfine structures of the molecular iodine transitions at 578 nm

    NASA Astrophysics Data System (ADS)

    Kobayashi, Takumi; Akamatsu, Daisuke; Hosaka, Kazumoto; Inaba, Hajime; Okubo, Sho; Tanabe, Takehiko; Yasuda, Masami; Onae, Atsushi; Hong, Feng-Lei

    2016-04-01

    We report absolute frequency measurements of 81 hyperfine components of the rovibrational transitions of molecular iodine at 578 nm using the second harmonic generation of an 1156-nm external-cavity diode laser and a fiber-based optical frequency comb. The relative uncertainties of the measured absolute frequencies are typically $1.4\\times10^{-11}$. Accurate hyperfine constants of four rovibrational transitions are obtained by fitting the measured hyperfine splittings to a four-term effective Hamiltonian including the electric quadrupole, spin-rotation, tensor spin-spin, and scalar spin-spin interactions. The observed transitions can be good frequency references at 578 nm, and are especially useful for research using atomic ytterbium since the transitions are close to the $^{1}S_{0}-^{3}P_{0}$ clock transition of ytterbium.

  4. Absolute Frequency Measurements of the D1 and D2 Transitions in Aatomic Li

    NASA Astrophysics Data System (ADS)

    Sheets, Donal; Almaguer, Jose; Baron, Jacob; Elgee, Peter; Rowan, Michael; Stalnaker, Jason

    2014-05-01

    We present preliminary results from our measurements of the D1 and D2 transitions in Li. The data were obtained from a collimated atomic beam excited by light from an extended cavity diode laser. The frequency of the diode laser was stabilized to an optical frequency comb, providing absolute frequency measurement and control of the excitation laser frequency. These measurements will provide a stringent test of atomic structure calculations and yield information about the nuclear structure. We also discuss plans to extend the technique to other high-lying states in lithium. Funded by the NIST Precision Measurements Grant and NSF Award #1305591.

  5. Radio frequency controlled synthetic wavelength sweep for absolute distance measurement by optical interferometry

    SciTech Connect

    Le Floch, Sebastien; Salvade, Yves; Mitouassiwou, Rostand; Favre, Patrick

    2008-06-01

    We present a new technique applied to the variable optical synthetic wavelength generation in optical interferometry. It consists of a chain of optical injection locking among three lasers: first a distributed-feedback laser is used as a master to injection lock an intensity-modulated laser that is directly modulated around 15 GHz by a radio frequency generator on a sideband. A second distributed-feedback laser is injection locked on another sideband of the intensity-modulated laser. The variable synthetic wavelength for absolute distance measurement is simply generated by sweeping the radio frequency over a range of several hundred megahertz, which corresponds to the locking range of the two slave lasers. In this condition, the uncertainty of the variable synthetic wavelength is equivalent to the radio frequency uncertainty. This latter has a relative accuracy of 10{sup -7} or better, resulting in a resolution of {+-}25 {mu}m for distances exceeding tens of meters. The radio frequency generator produces a linear frequency sweep of 1 ms duration (i.e., exactly equal to one absolute distance measurement acquisition time), with frequency steps of about 1 MHz. Finally, results of absolute distance measurements for ranges up to 10 m are presented.

  6. Radio frequency controlled synthetic wavelength sweep for absolute distance measurement by optical interferometry.

    PubMed

    Le Floch, Sébastien; Salvadé, Yves; Mitouassiwou, Rostand; Favre, Patrick

    2008-06-01

    We present a new technique applied to the variable optical synthetic wavelength generation in optical interferometry. It consists of a chain of optical injection locking among three lasers: first a distributed-feedback laser is used as a master to injection lock an intensity-modulated laser that is directly modulated around 15 GHz by a radio frequency generator on a sideband. A second distributed-feedback laser is injection locked on another sideband of the intensity-modulated laser. The variable synthetic wavelength for absolute distance measurement is simply generated by sweeping the radio frequency over a range of several hundred megahertz, which corresponds to the locking range of the two slave lasers. In this condition, the uncertainty of the variable synthetic wavelength is equivalent to the radio frequency uncertainty. This latter has a relative accuracy of 10(-7) or better, resulting in a resolution of +/-25 microm for distances exceeding tens of meters. The radio frequency generator produces a linear frequency sweep of 1 ms duration (i.e., exactly equal to one absolute distance measurement acquisition time), with frequency steps of about 1 MHz. Finally, results of absolute distance measurements for ranges up to 10 m are presented. PMID:18516123

  7. Absolute frequency measurement of the neutral 40Ca optical frequency standard at 657 nm based on microkelvin atoms

    NASA Astrophysics Data System (ADS)

    Wilpers, G.; Oates, C. W.; Diddams, S. A.; Bartels, A.; Fortier, T. M.; Oskay, W. H.; Bergquist, J. C.; Jefferts, S. R.; Heavner, T. P.; Parker, T. E.; Hollberg, L.

    2007-04-01

    We report an absolute frequency measurement of the optical clock transition at 657 nm in 40Ca with a relative uncertainty of 7.5 × 10-15, one of the most accurate frequency measurements of a neutral atom optical transition to date. The frequency (455 986 240 494 135.8 ± 3.4) Hz was measured by stabilizing a diode laser system to a spectroscopic signal derived from an ensemble of 106 atoms cooled in two stages to a temperature of 10 µK. The measurement used a femtosecond-laser-based frequency comb to compare the Ca transition frequency with that of the single-ion 199Hg+ optical frequency standard at NIST. The Hg+ frequency was simultaneously calibrated relative to the NIST Cs fountain via the NIST time scale to yield an absolute value for the Ca transition frequency. The relative fractional instability between the two optical standards was 2 × 10-15 for 10 s of averaging time and 2 × 10-16 for 2000 s.

  8. Absolute frequency measurements of the lithium D lines using an optical frequency comb

    NASA Astrophysics Data System (ADS)

    Simien, Clayton; Brewer, Samuel; Tan, Joseph; Gillaspy, John; Sansonetti, Craig

    2010-03-01

    High precision spectroscopic measurements of the isotope shift of low-lying lithium transitions can be combined with precise theory to probe the relative nuclear charge radii of various lithium isotopes. This technique is of particular interest for exotic isotopes for which scattering experiments are not feasible. But recently measured isotope shifts for the D1 and D2 lines of the stable isotopes ^6Li and ^7Li remain in strong disagreement with each other and with theory. Experimental values for the splitting isotope shift (SIS), believed to be the most reliable prediction, are not even consistent as to sign and disagree with theory by as much as 16 standard deviations. We will report results from a new experiment in progress at the NIST. We observe the D lines by crossing a highly collimated lithium beam with a very stable tunable laser. Unlike previous experiments, we directly measure the optical frequency of the laser at every data point by using an optical frequency comb referenced to a cesium clock. Initial results suggest that fully resolved lithium hyperfine components will be determined with an uncertainty of a few tens of kilohertz. We expect to obtain precise new values for the fine structure, hyperfine structure, and isotope shifts of the lithium D lines and a definitive test of the calculated SIS.

  9. Dynamic frequency-domain interferometer for absolute distance measurements with high resolution

    SciTech Connect

    Weng, Jidong; Liu, Shenggang; Ma, Heli; Tao, Tianjiong; Wang, Xiang; Liu, Cangli; Tan, Hua

    2014-11-15

    A unique dynamic frequency-domain interferometer for absolute distance measurement has been developed recently. This paper presents the working principle of the new interferometric system, which uses a photonic crystal fiber to transmit the wide-spectrum light beams and a high-speed streak camera or frame camera to record the interference stripes. Preliminary measurements of harmonic vibrations of a speaker, driven by a radio, and the changes in the tip clearance of a rotating gear wheel show that this new type of interferometer has the ability to perform absolute distance measurements both with high time- and distance-resolution.

  10. Simplified absolute phase retrieval of dual-frequency fringe patterns in fringe projection profilometry

    NASA Astrophysics Data System (ADS)

    Lu, Jin; Mo, Rong; Sun, Huibin; Chang, Zhiyong; Zhao, Xiaxia

    2016-04-01

    In fringe projection profilometry, a simplified method is proposed to recover absolute phase maps of two-frequency fringe patterns by using a unique mapping rule. The mapping rule is designed from the rounded phase values to the fringe order of each pixel. Absolute phase can be recovered by the fringe order maps. Unlike the existing techniques, where the lowest frequency of dual- or multiple-frequency fringe patterns must be single, the presented method breaks the limitation and simplifies the procedure of phase unwrapping. Additionally, due to many issues including ambient light, shadow, sharp edges, step height boundaries and surface reflectivity variations, a novel framework of automatically identifying and removing invalid phase values is also proposed. Simulations and experiments have been carried out to validate the performances of the proposed method.

  11. A Laser Frequency Comb System for Absolute Calibration of the VTT Echelle Spectrograph

    NASA Astrophysics Data System (ADS)

    Doerr, H.-P.; Steinmetz, T.; Holzwarth, R.; Kentischer, T.; Schmidt, W.

    2012-10-01

    A wavelength calibration system based on a laser frequency comb (LFC) was developed in a co-operation between the Kiepenheuer-Institut für Sonnenphysik, Freiburg, Germany and the Max-Planck-Institut für Quantenoptik, Garching, Germany for permanent installation at the German Vacuum Tower Telescope (VTT) on Tenerife, Canary Islands. The system was installed successfully in October 2011. By simultaneously recording the spectra from the Sun and the LFC, for each exposure a calibration curve can be derived from the known frequencies of the comb modes that is suitable for absolute calibration at the meters per second level. We briefly summarize some topics in solar physics that benefit from absolute spectroscopy and point out the advantages of LFC compared to traditional calibration techniques. We also sketch the basic setup of the VTT calibration system and its integration with the existing echelle spectrograph.

  12. Effects of relative and absolute frequency in the spectral weighting of loudness.

    PubMed

    Joshi, Suyash Narendra; Wróblewski, Marcin; Schmid, Kendra K; Jesteadt, Walt

    2016-01-01

    The loudness of broadband sound is often modeled as a linear sum of specific loudness across frequency bands. In contrast, recent studies using molecular psychophysical methods suggest that low and high frequency components contribute more to the overall loudness than mid frequencies. In a series of experiments, the contribution of individual components to the overall loudness of a tone complex was assessed using the molecular psychophysical method as well as a loudness matching task. The stimuli were two spectrally overlapping ten-tone complexes with two equivalent rectangular bandwidth spacing between the tones, making it possible to separate effects of relative and absolute frequency. The lowest frequency components of the "low-frequency" and the "high-frequency" complexes were 208 and 808 Hz, respectively. Perceptual-weights data showed emphasis on lowest and highest frequencies of both the complexes, suggesting spectral-edge related effects. Loudness matching data in the same listeners confirmed the greater contribution of low and high frequency components to the overall loudness of the ten-tone complexes. Masked detection thresholds of the individual components within the tone complex were not correlated with perceptual weights. The results show that perceptual weights provide reliable behavioral correlates of relative contributions of the individual frequency components to overall loudness of broadband sounds. PMID:26827032

  13. Noninvasive absolute cerebral oximetry with frequency-domain near-infrared spectroscopy

    NASA Astrophysics Data System (ADS)

    Hallacoglu, Bertan

    Near-infrared spectroscopy (NIRS) measurements of absolute concentrations of oxy-hemoglobin and deoxy-hemoglobin in the human brain can provide critical information about cerebral physiology in terms of cerebral blood volume, blood flow, oxygen delivery, and metabolic rate of oxygen. We developed several frequency domain NIRS data acquisition and analysis methods aimed at absolute measurements of hemoglobin concentration and saturation in cerebral tissue of adult human subjects. Extensive experimental investigations were carried out in various homogenous and two-layered tissue-mimicking phantoms, and biological tissues. The advantages and limitations of commonly used homogenous models and inversion strategies were thoroughly investigated. Prior to human subjects, extensive studies were carried out in in vivo animal models. In rabbits, absolute hemoglobin oxygen desaturation was shown to depend strongly on surgically induced testicular torsion. Methods developed in this study were then adapted for measurements in the rat brain. Absolute values were demonstrated to discern cerebrovascular impairment in a rat model of diet-induced vascular cognitive impairment. These results facilitated the development of clinically useful optical measures of cerebrovascular health. In a large group of human subjects, employing a homogeneous model for absolute measurements was shown to be reliable and robust. However, it was also shown to be limited due to the relatively thick extracerebral tissue. The procedure we develop in this work and the thesis thereof performs a nonlinear inversion procedure with six unknown parameters with no other prior knowledge for the retrieval of the optical coefficients and top layer thickness with high accuracy on two-layered media. Our absolute measurements of cerebral hemoglobin concentration and saturation are based on the discrimination of extracerebral and cerebral tissue layers, and they can enhance the impact of NIRS for cerebral hemodynamics and

  14. Absolute frequency stabilization of an injection-seeded optical parametric oscillator

    SciTech Connect

    Plusquellic, D.F.; Votava, O.; Nesbitt, D.J.

    1996-03-01

    A method is described that provides absolute frequency stabilization and calibration of the signal and idler waves generated by an injection-seeded optical parametric oscillator (OPO). The method makes use of a He{endash}Ne stabilized transfer cavity (TC) to control the frequencies of the cw sources used to seed both the pump laser and OPO cavity. The TC serves as a stable calibration source for the signal and idler waves by providing marker fringes as the seed laser is scanned. Additionally, an acoustic-optic modulator (AOM) is used to shift the OPO seed laser{close_quote}s frequency before locking it onto the TC. The sidebands of the AOM are tunable over more than one free spectral range of the TC, thereby permitting stabilization of the signal and idler waves at any frequency. A {plus_minus}25-MHz residual error in the absolute frequency stabilities of the pump, signal, and idler waves is experimentally demonstrated, which is roughly 30{percent} of the 160-MHz near-transform-limited linewidths of the signal and idler pulses. {copyright} {ital 1996 Optical Society of America.}

  15. Low-pressure line-shape study in molecular oxygen with absolute frequency reference

    NASA Astrophysics Data System (ADS)

    Domysławska, J.; Wójtewicz, S.; Cygan, A.; Bielska, K.; Lisak, D.; Masłowski, P.; Trawiński, R. S.; Ciuryło, R.

    2013-11-01

    We present a line-shape analysis of the rovibronic R1 Q2 transition of the oxygen B band resolved by the Pound-Drever-Hall-locked frequency-stabilized cavity ring-down spectroscopy technique in the low pressure range. The frequency axis of the spectra is linked by the ultra-narrow diode laser to the optical frequency comb in order to measure the absolute frequency at each point of the recorded spectra. Experimental spectra are fitted with various line-shape models: the Voigt profile, the Galatry profile, the Nelkin-Ghatak profile, the speed-dependent Voigt profile, and the speed-dependent Nelkin-Ghatak profile with quadratic and hypergeometric approximations for the speed dependence of collisional broadening and shifting. The influences of Dicke narrowing, speed-dependent effects, and correlation between phase- and velocity-changing collisions on the line shape are investigated. Values of line-shape parameters, including the absolute frequency of the transition 435685.24828(46) GHz, are reported.

  16. Comb-calibrated frequency-modulated continuous-wave ladar for absolute distance measurements.

    PubMed

    Baumann, Esther; Giorgetta, Fabrizio R; Coddington, Ian; Sinclair, Laura C; Knabe, Kevin; Swann, William C; Newbury, Nathan R

    2013-06-15

    We demonstrate a comb-calibrated frequency-modulated continuous-wave laser detection and ranging (FMCW ladar) system for absolute distance measurements. The FMCW ladar uses a compact external cavity laser that is swept quasi-sinusoidally over 1 THz at a 1 kHz rate. The system simultaneously records the heterodyne FMCW ladar signal and the instantaneous laser frequency at sweep rates up to 3400 THz/s, as measured against a free-running frequency comb (femtosecond fiber laser). Demodulation of the ladar signal against the instantaneous laser frequency yields the range to the target with 1 ms update rates, bandwidth-limited 130 μm resolution and a ~100 nm accuracy that is directly linked to the counted repetition rate of the comb. The precision is <100 nm at the 1 ms update rate and reaches ~6 nm for a 100 ms average. PMID:23938965

  17. Quantifying Discipline Practices Using Absolute vs. Relative Frequencies: Clinical and Research Implications for Child Welfare

    PubMed Central

    Lindhiem, Oliver; Shaffer, Anne; Kolko, David J.

    2014-01-01

    In the parent intervention outcome literatures, discipline practices are generally quantified as absolute frequencies or, less commonly, as relative frequencies. These differences in methodology warrant direct comparison as they have critical implications for study results and conclusions among treatments targeted at reducing parental aggression and harsh discipline. In this study, we directly compared the absolute frequency method and the relative frequency method for quantifying physically aggressive, psychologically aggressive, and nonaggressive discipline practices. Longitudinal data over a 3-year period came from an existing data set of a clinical trial examining the effectiveness of a psychosocial treatment in reducing parental physical and psychological aggression and improving child behavior (N = 139; Kolko et al., 2009). Discipline practices (both aggressive and nonaggressive) were assessed using the Conflict Tactics Scale (CTS; Straus et al., 1998). The two methods yielded different patterns of results, particularly for nonaggressive discipline strategies. We suggest that each method makes its own unique contribution to a more complete understanding of the association between parental aggression and intervention effects. PMID:24106146

  18. Measuring absolute frequencies beyond the GPS limit via long-haul optical frequency dissemination.

    PubMed

    Clivati, Cecilia; Cappellini, Giacomo; Livi, Lorenzo F; Poggiali, Francesco; de Cumis, Mario Siciliani; Mancini, Marco; Pagano, Guido; Frittelli, Matteo; Mura, Alberto; Costanzo, Giovanni A; Levi, Filippo; Calonico, Davide; Fallani, Leonardo; Catani, Jacopo; Inguscio, Massimo

    2016-05-30

    Global Positioning System (GPS) dissemination of frequency standards is ubiquitous at present, providing the most widespread time and frequency reference for the majority of industrial and research applications worldwide. On the other hand, the ultimate limits of the GPS presently curb further advances in high-precision, scientific and industrial applications relying on this dissemination scheme. Here, we demonstrate that these limits can be reliably overcome even in laboratories without a local atomic clock by replacing the GPS with a 642-km-long optical fiber link to a remote primary caesium frequency standard. Through this configuration we stably address the 1S0-3P0 clock transition in an ultracold gas of 173Yb, with a precision that exceeds the possibilities of a GPS-based measurement, dismissing the need for a local clock infrastructure to perform beyond-GPS high-precision tasks. We also report an improvement of two orders of magnitude in the accuracy on the transition frequency reported in literature. PMID:27410109

  19. Precision absolute frequency laser spectroscopy of argon II in parallel and antiparallel geometry using a frequency comb for calibration

    NASA Astrophysics Data System (ADS)

    Lioubimov, Vladimir

    A collinear fast ion beam laser apparatus was constructed and tested. It will be used on-line to the SLOW RI radioactive beam facility in RIKEN (Japan) and as in the present experiment for precision absolute frequency measurements of astrophysically important reference lines. In the current work we conducted absolute measurements of spectral lines of Ar+ ions using parallel and antiparallel geometries. To provide a reference for the laser wavelength iodine saturation spectroscopy was used. The precision of this reference was enhanced by simultaneously observing the beat node between the spectroscopy laser and the corresponding mode of a femtosecond laser frequency comb. When performing collinear and anticollinear measurements simultaneously for the laser induced fluorescence, the exact relativistic formula for the transition frequency n0=ncoll˙n anticoll can be applied. In this geometry ion source instabilities due to pressure and anode voltage fluctuation are minimized. The procedure of fluorescence lineshapes fitting is discussed and the errors in the measurements are estimated. The result is n0 = 485, 573, 619.7 +/- 0.3MHz corresponding to Dnn = 6 x 10-10 and is an improvement of two orders of magnitude over the NIST published value.

  20. Dual-frequency-moiré based absolute position sensing for lens focusing

    NASA Astrophysics Data System (ADS)

    Yin, Didi; Wang, Yahui; Di, Chengliang

    2015-10-01

    Micro motor, a typical equipment to adjust the zoom lens, together with a position feedback sensor constitute the closed position loop, which is the key factor to perform successfully accurate lens focusing. Traditionally, the incremental grating ruler tends to be adopted as the position sensor, which continues counting the number of grating pitches on a dynamic one-dimensional moving platform. Instead of incremental counting, this paper proposes a dual-frequency-moiré based absolute position sensing method for reading immediate position at static environment. According to the relative positions of two kind of moiré, the absolute position of the measurement point can be retrieve at nano-meters level through look-up table. By the way, the measurement range can be expanded to millimeters level satisfying the demands of lens focusing, and furthermore the measurement efficiency is improved greatly without dynamic moving. In order to verify the performances of proposed method, a model of dual-frequency-moiré is built, and theological principles are deduced. Finally, the simulation results indicate that, with established configurations, dual-frequency-moiré could measure position within 0~5000μm. At the same time, the measurement accuracy achieves nano-meters level.

  1. Use of the absolute phase in frequency modulated continuous wave plasma reflectometry

    SciTech Connect

    Cunningham, G.

    2008-08-15

    In frequency modulated continuous wave reflectometry, used for density profile measurement in fusion plasmas, it is usual to measure the beat frequency between the launched wave and the reflected wave, and from this to calculate the position of the reflecting layer in the plasma. The absolute phase of the beat signal is usually neglected. The reason is that the phase shift between sweeps is usually comparable with or more than 2{pi}, leading to an ambiguity that is impossible to resolve. However, recent observations on the MAST tokamak have shown that, under quiet plasma conditions (this term has to be defined), the phase shift between sweeps is small compared with 2{pi} and the phase ambiguity can be readily resolved. The reflectometer signal is then being analyzed as an interferometer signal would normally be, and there is a substantial improvement in spatial resolution. The method is illustrated by application to small edge localized mode precursor and allows what is believed to be the first quantitative measurement of the displacement of the plasma boundary by such a precursor mode. The errors in both the absolute phase measurement and the more conventional frequency measurement are also estimated.

  2. A dedicated pistonphone for absolute calibration of infrasound sensors at very low frequencies

    NASA Astrophysics Data System (ADS)

    He, Wen; He, Longbiao; Zhang, Fan; Rong, Zuochao; Jia, Shushi

    2016-02-01

    Aimed at the absolute calibration of infrasound sensors at very low frequencies, an upgraded and improved infrasonic pistonphone has been developed. The pistonphone was designed such that a very narrow clearance between the piston and its guide was realized based on an automatically-centered clearance-sealing structure, and a large volume rigid-walled chamber was also adopted, which improved the leakage time-constant of the chamber. A composite feedback control system was applied to the electromagnetic vibrator to control the precise motion of the piston. Performance tests and uncertainty analysis show that the leakage time-constant is so large, and the distortion of the sound pressure is so small, that the pistonphone can be used as a standard infrasound source in the frequency range from 0.001 Hz to 20 Hz. The low frequency property of the pistonphone has been verified through calibrating low frequency microphones. Comparison tests with the reciprocity method have shown that the pressure sensitivities from the pistonphone are not only reliable at common frequencies but also have smaller uncertainties at low frequencies.

  3. Stray-field-induced quadrupole shift and absolute frequency of the 688-THz {sup 171}Yb{sup +} single-ion optical frequency standard

    SciTech Connect

    Tamm, Chr.; Weyers, S.; Lipphardt, B.; Peik, E.

    2009-10-15

    We report experimental investigations of a single-ion optical frequency standard based on {sup 171}Yb{sup +}. The ion is confined in a cylindrically symmetric radiofrequency Paul trap. The reference transition is the {sup 2}S{sub 1/2}(F=0)-{sup 2}D{sub 3/2}(F{sup '}=2) electric quadrupole transition at 688 THz. Using a differential measurement scheme, we determine the shift of the reference transition frequency that occurs due to the interaction of the electric quadrupole moment of the {sup 2}D{sub 3/2} state with the gradient of the electrostatic stray field in the trap. We determine an upper limit for the instability of the quadrupole shift over times between 100 s to 20 h. We also observe the variations in the shift and in the applied stray-field compensation voltages that result from loading a new ion into the trap and during a subsequent storage period of 74 days. This information is utilized to measure the absolute frequency of the reference transition with an uncertainty that is a factor of 3 smaller than that of the previous measurement. Using a fiber laser based optical frequency comb generator and the cesium fountain clock CSF1 of PTB (Physikalisch-Technische Bundesanstalt), the frequency at 300 K temperature is determined as 688 358 979 309 306.62{+-}0.73 Hz.

  4. Absolute molecular transition frequencies measured by three cavity-enhanced spectroscopy techniques.

    PubMed

    Cygan, A; Wójtewicz, S; Kowzan, G; Zaborowski, M; Wcisło, P; Nawrocki, J; Krehlik, P; Śliwczyński, Ł; Lipiński, M; Masłowski, P; Ciuryło, R; Lisak, D

    2016-06-01

    Absolute frequencies of unperturbed (12)C(16)O transitions from the near-infrared (3-0) band were measured with uncertainties five-fold lower than previously available data. The frequency axis of spectra was linked to the primary frequency standard. Three different cavity enhanced absorption and dispersion spectroscopic methods and various approaches to data analysis were used to estimate potential systematic instrumental errors. Except for a well established frequency-stabilized cavity ring-down spectroscopy, we applied the cavity mode-width spectroscopy and the one-dimensional cavity mode-dispersion spectroscopy for measurement of absorption and dispersion spectra, respectively. We demonstrated the highest quality of the dispersion line shape measured in optical spectroscopy so far. We obtained line positions of the Doppler-broadened R24 and R28 transitions with relative uncertainties at the level of 10(-10). The pressure shifting coefficients were measured and the influence of the line asymmetry on unperturbed line positions was analyzed. Our dispersion spectra are the first demonstration of molecular spectroscopy with both axes of the spectra directly linked to the primary frequency standard, which is particularly desirable for the future reference-grade measurements of molecular spectra. PMID:27276950

  5. Absolute molecular transition frequencies measured by three cavity-enhanced spectroscopy techniques

    NASA Astrophysics Data System (ADS)

    Cygan, A.; Wójtewicz, S.; Kowzan, G.; Zaborowski, M.; Wcisło, P.; Nawrocki, J.; Krehlik, P.; Śliwczyński, Ł.; Lipiński, M.; Masłowski, P.; Ciuryło, R.; Lisak, D.

    2016-06-01

    Absolute frequencies of unperturbed 12C16O transitions from the near-infrared (3-0) band were measured with uncertainties five-fold lower than previously available data. The frequency axis of spectra was linked to the primary frequency standard. Three different cavity enhanced absorption and dispersion spectroscopic methods and various approaches to data analysis were used to estimate potential systematic instrumental errors. Except for a well established frequency-stabilized cavity ring-down spectroscopy, we applied the cavity mode-width spectroscopy and the one-dimensional cavity mode-dispersion spectroscopy for measurement of absorption and dispersion spectra, respectively. We demonstrated the highest quality of the dispersion line shape measured in optical spectroscopy so far. We obtained line positions of the Doppler-broadened R24 and R28 transitions with relative uncertainties at the level of 10-10. The pressure shifting coefficients were measured and the influence of the line asymmetry on unperturbed line positions was analyzed. Our dispersion spectra are the first demonstration of molecular spectroscopy with both axes of the spectra directly linked to the primary frequency standard, which is particularly desirable for the future reference-grade measurements of molecular spectra.

  6. Using absolute gravimeter data to determine vertical gravity gradients

    USGS Publications Warehouse

    Robertson, D.S.

    2001-01-01

    The position versus time data from a free-fall absolute gravimeter can be used to estimate the vertical gravity gradient in addition to the gravity value itself. Hipkin has reported success in estimating the vertical gradient value using a data set of unusually good quality. This paper explores techniques that may be applicable to a broader class of data that may be contaminated with "system response" errors of larger magnitude than were evident in the data used by Hipkin. This system response function is usually modelled as a sum of exponentially decaying sinusoidal components. The technique employed here involves combining the x0, v0 and g parameters from all the drops made during a site occupation into a single least-squares solution, and including the value of the vertical gradient and the coefficients of system response function in the same solution. The resulting non-linear equations must be solved iteratively and convergence presents some difficulties. Sparse matrix techniques are used to make the least-squares problem computationally tractable.

  7. Determination of absolute configuration using ab initio calculation of optical rotation.

    PubMed

    Stephens, P J; Devlin, F J; Cheeseman, J R; Frisch, M J; Bortolini, O; Besse, P

    2003-01-01

    Ab initio Density Functional Theory (DFT) calculations of transparent spectral region, discrete frequency specific rotations were used to assign the absolute configurations (ACs) of: 1, 2H-naphtho[1,8-bc]thiophene 1-oxide; 2, m-F-phenyl glycidic acid methyl ester; 3, o-Br-phenyl glycidic acid methyl ester; 4, p-CH(3)-phenyl glycidic acid methyl ester; 5, 2-(1-hydroxyethyl)-chromen-4-one; and 6, 6-Br-2-(1-hydroxyethyl)-chromen-4-one. The ACs of 5 and 6 were previously determined via X-ray crystallography to be: 5, R(-)/S(+); 6, R(+)/S(-). The ACs obtained using [alpha](D) are the same for both 5 and 6: R(+)/S(-). We conclude that the previously reported AC of 5 is incorrect. PMID:12884375

  8. Accurate determination of absolute carrier-envelope phase dependence using photo-ionization.

    PubMed

    Sayler, A M; Arbeiter, M; Fasold, S; Adolph, D; Möller, M; Hoff, D; Rathje, T; Fetić, B; Milošević, D B; Fennel, T; Paulus, G G

    2015-07-01

    The carrier-envelope phase (CEP) dependence of few-cycle above-threshold ionization (ATI) of Xe is calibrated for use as a reference measurement for determining and controlling the absolute CEP in other interactions. This is achieved by referencing the CEP-dependent ATI measurements of Xe to measurements of atomic H, which are in turn referenced to ab initio calculations for atomic H. This allows for the accurate determination of the absolute CEP dependence of Xe ATI, which enables relatively easy determination of the offset between the relative CEP measured and/or controlled by typical devices and the absolute CEP in the interaction. PMID:26125386

  9. Absolute frequency measurement of the 7s2 1S0-7s7p 1P1 transition in Ra225

    NASA Astrophysics Data System (ADS)

    Santra, B.; Dammalapati, U.; Groot, A.; Jungmann, K.; Willmann, L.

    2014-10-01

    Transition frequencies were determined for transitions in Ra in an atomic beam and for reference lines in Te2 molecules in a vapor cell. The absolute frequencies were calibrated against a GPS stabilized Rb clock by means of an optical frequency comb. The 7s21S0(F=1/2)-7s7p1P1(F =3/2) transition in Ra225 was determined to be 621042124(2)MHz. The measurements provide input for designing efficient and robust laser cooling of Ra atoms in preparation of a search for a permanent electric dipole moment in Ra isotopes.

  10. Determination of the Absolute Number of Cytokine mRNA Molecules within Individual Activated Human T Cells

    NASA Technical Reports Server (NTRS)

    Karr, Laurel J.; Marshall, Gwen; Hockett, Richard D.; Bucy, R. Pat; Curreri, Peter A. (Technical Monitor)

    2002-01-01

    A primary function of activated T cells is the expression and subsequent secretion of cytokines, which orchestrate the differentiation of other lymphocytes, modulate antigen presenting cell activity, and alter vascular endothelium to mediate an immune response. Since many features of immune regulation probably result from modest alterations of endogenous rates of multiple interacting processes, quantitative analysis of the frequency and specific activity of individual T cells is critically important. Using a coordinated set of quantitative methods, the absolute number of molecules of several key cytokine mRNA species in individual T cells has been determined. The frequency of human blood T cells activated in vitro by mitogens and recall protein antigens was determined by intracellular cytokine protein staining, in situ hybridization for cytokine mRNA, and by limiting dilution analysis for cytokine mRNA+ cells. The absolute number of mRNA molecules was simultaneously determined in both homogenates of the entire population of cells and in individual cells obtained by limiting dilution, using a quantitative, competitive RT-PCR assay. The absolute numbers of mRNA molecules in a population of cells divided by the frequency of individual positive cells, yielded essentially the same number of mRNA molecules per cell as direct analysis of individual cells by limiting dilution analysis. Mean numbers of mRNA per positive cell from both mitogen and antigen activated T cells, using these stimulation conditions, were 6000 for IL-2, 6300 for IFN-gamma, and 1600 for IL-4.

  11. Determination of the Absolute Stereochemistry of Secondary Alcohols: An Advanced Organic Chemistry Experiment for Undergraduate Students.

    ERIC Educational Resources Information Center

    Bandaranayake, Wickramasinghe M.

    1980-01-01

    Describes experiments which can be completed in five four-hour laboratory sessions, including two synthesis (alpha-phenylbutyric and alpha-phenylbutyric acid anhydride) and determining the absolute stereochemistry of secondary alcohols using the synthetic products. (JN)

  12. A Simple Watt Balance for the Absolute Determination of Mass

    ERIC Educational Resources Information Center

    Quinn, Terry; Quinn, Lucas; Davis, Richard

    2013-01-01

    A watt balance is an electromechanical device that allows a mass to be determined in terms of measurable electrical and mechanical quantities, themselves traceable to the fundamental constants of physics. International plans are well advanced to redefine the unit of mass, the kilogram, in terms of a fixed numerical value for the Planck constant. A…

  13. Correlation of symptom clusters of schizophrenia with absolute powers of main frequency bands in quantitative EEG

    PubMed Central

    Gross, Andres; Joutsiniemi, Sirkka-Liisa; Rimon, Ranan; Appelberg, Björn

    2006-01-01

    Background Research of QEEG activity power spectra has shown intriguing results in patients with schizophrenia. Different symptom clusters have been correlated to QEEG frequency bands. The findings have been to some extent inconsistent. Replication of the findings of previous research is thus an important task. In the current study we investigated the correlations between the absolute powers of delta, theta, alpha, and beta frequency bands over the fronto-central scalp area (FC) with the PANSS subscales and the Liddle's factors in 16 patients with schizophrenia. The authors hypothesised a priori the correlations reported by Harris et al (1999) of PANSS negative subscale with delta power, Liddle's psychomotor poverty with delta and beta powers, disorganisation with delta power and reality distortion with alpha power on the midline FC. Methods The sample consisted of 16 patients with chronic schizophrenia considered as having insufficient clinical response to conventional antipsychotic treatment and evidencing a relapse. The correlations between quantitative electroencephalography (QEEG) absolute powers of delta (1.5–3.0 Hz), theta (3.0–7.5 Hz), alpha (7.5–12.5 Hz), and beta (12.5–20.0 Hz) frequency bands over the fronto-central scalp area (FC) with PANSS subscales and Liddle's factors (reality distortion, disorganisation, psychomotor poverty) were investigated. Results Significant positive correlations were found between the beta and psychomotor poverty (p < 0.05). Trends towards positive correlations (p < 0.1) were observed between delta and PANSS negative subscale and psychomotor poverty. Alpha did not correlate with reality distortion and delta did not correlate with disorganisation. Post hoc analysis revealed correlations of the same magnitude between beta and psychopathology generally over FC. Conclusion The a priori hypothesis was partly supported by the correlation of the beta and psychomotor poverty. Liddle's factors showed correlations of the same

  14. On determining absolute entropy without quantum theory or the third law of thermodynamics

    NASA Astrophysics Data System (ADS)

    Steane, Andrew M.

    2016-04-01

    We employ classical thermodynamics to gain information about absolute entropy, without recourse to statistical methods, quantum mechanics or the third law of thermodynamics. The Gibbs–Duhem equation yields various simple methods to determine the absolute entropy of a fluid. We also study the entropy of an ideal gas and the ionization of a plasma in thermal equilibrium. A single measurement of the degree of ionization can be used to determine an unknown constant in the entropy equation, and thus determine the absolute entropy of a gas. It follows from all these examples that the value of entropy at absolute zero temperature does not need to be assigned by postulate, but can be deduced empirically.

  15. Measurement of absolute transition frequencies of {sup 87}Rb to nS and nD Rydberg states by means of electromagnetically induced transparency

    SciTech Connect

    Mack, Markus; Karlewski, Florian; Hattermann, Helge; Hoeckh, Simone; Jessen, Florian; Cano, Daniel; Fortagh, Jozsef

    2011-05-15

    We report the measurement of absolute excitation frequencies of {sup 87}Rb to nS and nD Rydberg states. The Rydberg transition frequencies are obtained by observing electromagnetically induced transparency on a rubidium vapor cell. The accuracy of the measurement of each state is < or approx. 1 MHz, which is achieved by frequency stabilizing the two diode lasers employed for the spectroscopy to a frequency comb and a frequency comb calibrated wavelength meter, respectively. Based on the spectroscopic data we determine the quantum defects of {sup 87}Rb, and compare it with previous measurements on {sup 85}Rb. We determine the ionization frequency from the 5S{sub 1/2}(F=1) ground state of {sup 87}Rb to 1010.029 164 6(3)THz, providing the binding energy of the ground state with an accuracy improved by two orders of magnitude.

  16. A system for measuring absolute frequencies of up to 4.25 THz using a Josephson point contact

    NASA Astrophysics Data System (ADS)

    Mild, Yukinobu; Onae, Atsushi; Kurosawa, Tomizo; Sakuma, Eiichi

    1993-11-01

    A system for measuring the absolute frequency of a far-infrared (FIR) laser is described. Josephson point contacts have been utilized in the system as a frequency harmonic mixer connecting microwaves and optically pumped CH3OH laser lines. The Josephson point contacts are capable of generating beat signals of 90 GHz microwaves and FIR waves of up to 4.25 THz. To measure the frequency of the beat signals from the Josephson junction with a frequency counter, tracking oscillators have been developed, which tracks the beat signals by phase locking and regenerate clean signals for frequency counting. It is shown that the absolute frequency can be measured to an accuracy of about 100 Hz by using the tracking oscillators.

  17. Selective polymer materials: absolute determination of their sorption properties

    NASA Astrophysics Data System (ADS)

    Jakusch, Michael; Mizaikoff, Boris

    2001-02-01

    Several types of selective materials are frequently used in chemical sensors such as natural antibodies, synthetic host substances (calixarenes, cyclodextrines, etc.) molecularly imprinted materials, or conventional polymers. For a systematic development of those materials, their sorption behavior for interesting analyte substances and potentially interfering compounds has to be thoroughly characterized, which can be a time-consuming and error-prone task. Moreover, using the respective sensor principle itself for this characterization an exact relation between the sensor signal and the underlying partition coefficient or sorption isotherm can often not be obtained. In this paper, we present an automated method for the direct determination of polymer/water partition coefficients of volatile organic compounds that consists of an automated fluid handling system, a dedicated partitioning cell and a purge-and-trap gas chromatography (PT-GC) unit. The main application of this novel system is the characterization of layer materials for infrared evanescent wave spectroscopic (IR-EWS) sensors, however an extension to other problems is conceivable. The whole experimental procedure comprising calibration of the GC system, preparation of test solutions, analyte partitioning, sample analysis, as well as the necessary cleaning steps is performed automatically under computer control. Hence, this system can be operated unattendedly, yielding a reasonable throughput with comparatively low expenditure of human labor.

  18. A new determination of the Geneva photometric passbands and their absolute calibration

    NASA Astrophysics Data System (ADS)

    Rufener, F.; Nicolet, B.

    The consensus regarding the absolute calibrations of the spectra of alpha Lyr and subdwarfs provoked a revision of the calibration of the Geneva photometric system passbands. The alterations made to the earlier version by Rufener and Maeder (1971) are smaller than plus or minus -5 percent. The new response functions are presented in tabular form for an equiphotonic flux. An absolute spectrophotometric adjustment allows to obtain for each entry of the Geneva catalog (28,000 stars) a corresponding spectrophotometric description in SI units. The definition and the means of computing the necessary quasi-isophotal frequencies or wavelengths are given. The coherence of the Geneva catalog with several sets of absolute spectrophotometric data is examined. A correction for the entire Gunn and Stryker (1983) catalog is proposed.

  19. Principles and procedures for determining absolute differential electron-molecule (atom) scattering cross sections

    NASA Technical Reports Server (NTRS)

    Nickel, J. C.; Zetner, P. W.; Shen, G.; Trajmar, S.

    1989-01-01

    Procedures and calibration techniques for measuring the absolute elastic and inelastic differential cross sections (DCS) for electron impact on molecular (atomic) species are described and illustrated by examples. The elastic DCS for the molecule under study is first determined by calibration against helium using the relative flow technique. The second step involves the production of energy-loss spectra for the instrument response function, the unfolding of overlapping inelastic structures and the normalization of inelastic intensities to the elastic cross sections. It is concluded that this method of determining absolute differential electron-molecule (atom) scattering cross sections is generally applicable and provides reliable results.

  20. Determination of the absolute configuration of sialic acids in gangliosides from the sea cucumber Cucumaria echinata.

    PubMed

    Kisa, Fumiaki; Yamada, Koji; Miyamoto, Tomofumi; Inagaki, Masanori; Higuchi, Ryuichi

    2007-07-01

    Enantiomeric pairs of sialic acid, D- and L-NeuAc (N-acetylneuraminic acid), were converted to D- and L-arabinose, respectively, by chemical degradation. Using this method, the absolute configuration of the sialic acid residues, NeuAc and NeuGc (N-glycolylneuraminic acid), in the gangliosides from the sea cucumber Cucumaria echinata was determined to be the D-form. Although naturally occurring sialic acids have been believed to be the D-form on the basis of biosynthetic evidence, this is the first report of the determination of the absolute configuration of the sialic acid residues in gangliosides using chemical methods. PMID:17603199

  1. Infrared mapping of ultrasound fields generated by medical transducers: Feasibility of determining absolute intensity levels

    PubMed Central

    Khokhlova, Vera A.; Shmeleva, Svetlana M.; Gavrilov, Leonid R.; Martin, Eleanor; Sadhoo, Neelaksh; Shaw, Adam

    2013-01-01

    Considerable progress has been achieved in the use of infrared (IR) techniques for qualitative mapping of acoustic fields of high intensity focused ultrasound (HIFU) transducers. The authors have previously developed and demonstrated a method based on IR camera measurement of the temperature rise induced in an absorber less than 2 mm thick by ultrasonic bursts of less than 1 s duration. The goal of this paper was to make the method more quantitative and estimate the absolute intensity distributions by determining an overall calibration factor for the absorber and camera system. The implemented approach involved correlating the temperature rise measured in an absorber using an IR camera with the pressure distribution measured in water using a hydrophone. The measurements were conducted for two HIFU transducers and a flat physiotherapy transducer of 1 MHz frequency. Corresponding correction factors between the free field intensity and temperature were obtained and allowed the conversion of temperature images to intensity distributions. The system described here was able to map in good detail focused and unfocused ultrasound fields with sub-millimeter structure and with local time average intensity from below 0.1 W/cm2 to at least 50 W/cm2. Significantly higher intensities could be measured simply by reducing the duty cycle. PMID:23927199

  2. Infrared mapping of ultrasound fields generated by medical transducers: feasibility of determining absolute intensity levels.

    PubMed

    Khokhlova, Vera A; Shmeleva, Svetlana M; Gavrilov, Leonid R; Martin, Eleanor; Sadhoo, Neelaksh; Shaw, Adam

    2013-08-01

    Considerable progress has been achieved in the use of infrared (IR) techniques for qualitative mapping of acoustic fields of high intensity focused ultrasound (HIFU) transducers. The authors have previously developed and demonstrated a method based on IR camera measurement of the temperature rise induced in an absorber less than 2 mm thick by ultrasonic bursts of less than 1 s duration. The goal of this paper was to make the method more quantitative and estimate the absolute intensity distributions by determining an overall calibration factor for the absorber and camera system. The implemented approach involved correlating the temperature rise measured in an absorber using an IR camera with the pressure distribution measured in water using a hydrophone. The measurements were conducted for two HIFU transducers and a flat physiotherapy transducer of 1 MHz frequency. Corresponding correction factors between the free field intensity and temperature were obtained and allowed the conversion of temperature images to intensity distributions. The system described here was able to map in good detail focused and unfocused ultrasound fields with sub-millimeter structure and with local time average intensity from below 0.1 W/cm(2) to at least 50 W/cm(2). Significantly higher intensities could be measured simply by reducing the duty cycle. PMID:23927199

  3. Chiral liquid chromatography contribution to the determination of the absolute configuration of enantiomers.

    PubMed

    Roussel, Christian; Del Rio, Alberto; Pierrot-Sanders, Johanna; Piras, Patrick; Vanthuyne, Nicolas

    2004-05-28

    The review covers examples in which chiral HPLC, as a source of pure enantiomers, has been combined with classical methods (X-ray, vibrational circular dichroism (VCD), enzymatic resolutions, nuclear magnetic resonance (NMR) techniques, optical rotation, circular dichroism (CD)) for the on- or off-line determination of absolute configuration of enantiomers. Furthermore, it is outlined that chiral HPLC, which associates enantioseparation process and classical purification process, opens new perspectives in the classical determination of absolute configuration by chemical correlation or chemical interconversion methods. The review also contains a discussion about the various approaches to predict the absolute configuration from the retention behavior of the enantiomers on chiral stationary phases (CSPs). Some examples illustrate the advantages and limitations of molecular modeling methods and the use of chiral recognition models. The assumptions underlying some of these methods are critically analyzed and some possible emerging new strategies are outlined. PMID:15214673

  4. Determination of absolute configuration of natural products: theoretical calculation of electronic circular dichroism as a tool

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Determination of absolute configuration (AC) is one of the most challenging features in the structure elucidation of chiral natural products, especially those with complex structures. With revolutionary advancements in the area of quantum chemical calculations of chiroptical spectroscopy over the pa...

  5. Determination of absolute threshold and just noticeable difference in the sensory perception of pungency.

    PubMed

    Orellana-Escobedo, L; Ornelas-Paz, J J; Olivas, G I; Guerrero-Beltran, J A; Jimenez-Castro, J; Sepulveda, D R

    2012-03-01

    Absolute threshold and just noticeable difference (JND) were determined for the perception of pungency using chili pepper in aqueous solutions. Absolute threshold and JND were determined using 2 alternative forced-choice sensory tests tests. High-performance liquid chromatography technique was used to determine capsaicinoids concentration in samples used for sensory analysis. Sensory absolute threshold was 0.050 mg capsaicinoids/kg sample. Five JND values were determined using 5 reference solutions with different capsaicinoids concentration. JND values changed proportionally as capsaicinoids concentration of the reference sample solutions changed. Weber fraction remained stable for the first 4 reference capsaicinoid solutions (0.05, 0.11, 0.13, and 0.17 mg/kg) but changed when the most concentrated reference capsaicinoids solution was used (0.23 mg/kg). Quantification limit for instrumental analysis was 1.512 mg/kg capsaicinoids. Sensory methods employed in this study proved to be more sensitive than instrumental methods. Practical Application: A better understanding of the process involved in the sensory perception of pungency is currently required because "hot" foods are becoming more popular in western cuisine. Absolute thresholds and differential thresholds are useful tools in the formulation and development of new food products. These parameters may help in defining how much chili pepper is required in a formulated product to ensure a perceptible level of pungency, as well as in deciding how much more chili pepper is required in a product to produce a perceptible increase in its pungency. PMID:22384966

  6. Fast, Computer Supported Experimental Determination of Absolute Zero Temperature at School

    ERIC Educational Resources Information Center

    Bogacz, Bogdan F.; Pedziwiatr, Antoni T.

    2014-01-01

    A simple and fast experimental method of determining absolute zero temperature is presented. Air gas thermometer coupled with pressure sensor and data acquisition system COACH is applied in a wide range of temperature. By constructing a pressure vs temperature plot for air under constant volume it is possible to obtain--by extrapolation to zero…

  7. Mosher Amides: Determining the Absolute Stereochemistry of Optically-Active Amines

    ERIC Educational Resources Information Center

    Allen, Damian A.; Tomaso, Anthony E., Jr.; Priest, Owen P.; Hindson, David F.; Hurlburt, Jamie L.

    2008-01-01

    The use of chiral reagents for the derivatization of optically-active amines and alcohols for the purpose of determining their enantiomeric purity or absolute configuration is a tool used by many chemists. Among the techniques used, Mosher's amide and Mosher's ester analyses are among the most reliable and one of the most often used. Despite this,…

  8. Metrological activity determination of 133Ba by sum-peak absolute method

    NASA Astrophysics Data System (ADS)

    da Silva, R. L.; de Almeida, M. C. M.; Delgado, J. U.; Poledna, R.; Santos, A.; de Veras, E. V.; Rangel, J.; Trindade, O. L.

    2016-07-01

    The National Laboratory for Metrology of Ionizing Radiation provides gamma sources of radionuclide and standardized in activity with reduced uncertainties. Relative methods require standards to determine the sample activity while the absolute methods, as sum-peak, not. The activity is obtained directly with good accuracy and low uncertainties. 133Ba is used in research laboratories and on calibration of detectors for analysis in different work areas. Classical absolute methods don't calibrate 133Ba due to its complex decay scheme. The sum-peak method using gamma spectrometry with germanium detector standardizes 133Ba samples. Uncertainties lower than 1% to activity results were obtained.

  9. Determination of absolute configuration using heavy atom based co-crystallization method: Halogen atom effects

    NASA Astrophysics Data System (ADS)

    Wang, Jian-Rong; Fan, Xiaowu; Ding, Qiaoce; Mei, Xuefeng

    2016-09-01

    Heavy atom (chloride, bromide, and iodide) based co-crystals for determination of absolute configuration (AC) for chiral molecules were synthesized and evaluated. Co-crystals of cholestanol and L-ascorbic acid were analysed and the effects and potential benefits of varying the heavy atom are discussed. Changing the halogen atoms (chloride, bromide, or iodide) affects the co-crystal formation, X-ray absorption, and anomalous dispersion, and hence the ability to determine AC.

  10. Absolute frequency and isotope shift of the magnesium (3 s2) 1S0→(3 s 3 d ) 1D2 two-photon transition by direct frequency-comb spectroscopy

    NASA Astrophysics Data System (ADS)

    Peters, E.; Reinhardt, S.; Hänsch, Th. W.; Udem, Th.

    2015-12-01

    We use a picosecond frequency-doubled mode-locked titanium sapphire laser to generate a frequency comb at 431 nm in order to probe the (3 s2) 1S0 →(3 s 3 d ) 1D2 transition in atomic magnesium. Using a second, self-referenced femtosecond frequency comb, the absolute transition frequency and the 24Mg and 26Mg isotope shift is determined relative to a global-positioning-system-referenced hydrogen maser. Our result for the transition frequency of the main isotope 24Mg of 1 391 128 606.14 (12 ) MHz agrees with previous measurements and reduces its uncertainty by four orders of magnitude. For the isotope shift we find δ ν26 ,24=3915.13 (39 ) MHz. Accurate values for transition frequencies in Mg are relevant in astrophysics and to test atomic structure calculations.

  11. Isolation and determination of absolute configurations of insect-produced methyl-branched hydrocarbons.

    PubMed

    Bello, Jan E; McElfresh, J Steven; Millar, Jocelyn G

    2015-01-27

    Although the effects of stereochemistry have been studied extensively for volatile insect pheromones, little is known about the effects of chirality in the nonvolatile methyl-branched hydrocarbons (MBCHs) used by many insects as contact pheromones. MBCHs generally contain one or more chiral centers and so two or more stereoisomeric forms are possible for each structure. However, it is not known whether insects biosynthesize these molecules in high stereoisomeric purity, nor is it known whether insects can distinguish the different stereoisomeric forms of MBCHs. This knowledge gap is due in part to the lack of methods for isolating individual MBCHs from the complex cuticular hydrocarbon (CHC) blends of insects, as well as the difficulty in determining the absolute configurations of the isolated MBCHs. To address these deficiencies, we report a straightforward method for the isolation of individual cuticular hydrocarbons from the complex CHC blend. The method was used to isolate 36 pure MBCHs from 20 species in nine insect orders. The absolute stereochemistries of the purified MBCHs then were determined by digital polarimetry. The absolute configurations of all of the isolated MBCHs were determined to be (R) by comparison with a library of synthesized, enantiomerically pure standards, suggesting that the biosynthetic pathways used to construct MBCHs are highly conserved within the Insecta. The development of a straightforward method for isolation of specific CHCs will enable determination of their functional roles by providing pure compounds for bioassays. PMID:25583471

  12. Isolation and determination of absolute configurations of insect-produced methyl-branched hydrocarbons

    PubMed Central

    Bello, Jan E.; McElfresh, J. Steven; Millar, Jocelyn G.

    2015-01-01

    Although the effects of stereochemistry have been studied extensively for volatile insect pheromones, little is known about the effects of chirality in the nonvolatile methyl-branched hydrocarbons (MBCHs) used by many insects as contact pheromones. MBCHs generally contain one or more chiral centers and so two or more stereoisomeric forms are possible for each structure. However, it is not known whether insects biosynthesize these molecules in high stereoisomeric purity, nor is it known whether insects can distinguish the different stereoisomeric forms of MBCHs. This knowledge gap is due in part to the lack of methods for isolating individual MBCHs from the complex cuticular hydrocarbon (CHC) blends of insects, as well as the difficulty in determining the absolute configurations of the isolated MBCHs. To address these deficiencies, we report a straightforward method for the isolation of individual cuticular hydrocarbons from the complex CHC blend. The method was used to isolate 36 pure MBCHs from 20 species in nine insect orders. The absolute stereochemistries of the purified MBCHs then were determined by digital polarimetry. The absolute configurations of all of the isolated MBCHs were determined to be (R) by comparison with a library of synthesized, enantiomerically pure standards, suggesting that the biosynthetic pathways used to construct MBCHs are highly conserved within the Insecta. The development of a straightforward method for isolation of specific CHCs will enable determination of their functional roles by providing pure compounds for bioassays. PMID:25583471

  13. Improved statistical determination of absolute neutrino masses via radiative emission of neutrino pairs from atoms

    NASA Astrophysics Data System (ADS)

    Zhang, Jue; Zhou, Shun

    2016-06-01

    The atomic transition from an excited state |e ⟩ to the ground state |g ⟩ by emitting a neutrino pair and a photon, i.e., |e ⟩→|g ⟩+|γ ⟩+|νi⟩+|ν¯j⟩ with i , j =1 , 2, 3, has been proposed by Yoshimura and his collaborators as an alternative way to determine the absolute scale m0 of neutrino masses. More recently, a statistical analysis of the fine structure of the photon spectrum from this atomic process has been performed [N. Song et al. Phys. Rev. D 93, 013020 (2016)] to quantitatively examine the experimental requirements for a realistic determination of absolute neutrino masses. In this paper, we show how to improve the statistical analysis and demonstrate that the previously required detection time can be reduced by one order of magnitude for the case of a 3 σ determination of m0˜0.01 eV with an accuracy better than 10%. Such an improvement is very encouraging for further investigations on measuring absolute neutrino masses through atomic processes.

  14. Absolute ages from crater statistics: Using radiometric ages of Martian samples for determining the Martian cratering chronology

    NASA Technical Reports Server (NTRS)

    Neukum, G.

    1988-01-01

    In the absence of dates derived from rock samples, impact crater frequencies are commonly used to date Martian surface units. All models for absolute dating rely on the lunar cratering chronology and on the validity of its extrapolation to Martian conditions. Starting from somewhat different lunar chronologies, rather different Martian cratering chronologies are found in the literature. Currently favored models are compared. The differences at old ages are significant, the differences at younger ages are considerable and give absolute ages for the same crater frequencies as different as a factor of 3. The total uncertainty could be much higher, though, since the ratio of lunar to Martian cratering rate which is of basic importance in the models is believed to be known no better than within a factor of 2. Thus, it is of crucial importance for understanding the the evolution of Mars and determining the sequence of events to establish an unambiguous Martian cratering chronology from crater statistics in combination with clean radiometric ages of returned Martian samples. For the dating goal, rocks should be as pristine as possible from a geologically simple area with a one-stage emplacement history of the local formation. A minimum of at least one highland site for old ages, two intermediate-aged sites, and one very young site is needed.

  15. Electron cyclotron emission measurements on JET: Michelson interferometer, new absolute calibration, and determination of electron temperature.

    PubMed

    Schmuck, S; Fessey, J; Gerbaud, T; Alper, B; Beurskens, M N A; de la Luna, E; Sirinelli, A; Zerbini, M

    2012-12-01

    At the fusion experiment JET, a Michelson interferometer is used to measure the spectrum of the electron cyclotron emission in the spectral range 70-500 GHz. The interferometer is absolutely calibrated using the hot/cold technique and, in consequence, the spatial profile of the plasma electron temperature is determined from the measurements. The current state of the interferometer hardware, the calibration setup, and the analysis technique for calibration and plasma operation are described. A new, full-system, absolute calibration employing continuous data acquisition has been performed recently and the calibration method and results are presented. The noise level in the measurement is very low and as a result the electron cyclotron emission spectrum and thus the spatial profile of the electron temperature are determined to within ±5% and in the most relevant region to within ±2%. The new calibration shows that the absolute response of the system has decreased by about 15% compared to that measured previously and possible reasons for this change are presented. Temperature profiles measured with the Michelson interferometer are compared with profiles measured independently using Thomson scattering diagnostics, which have also been recently refurbished and recalibrated, and agreement within experimental uncertainties is obtained. PMID:23282107

  16. Determination of the absolute configuration of a chiral epoxide using foil induced Coulomb explosion imaging

    NASA Astrophysics Data System (ADS)

    Herwig, P.; Zawatzky, K.; Schwalm, D.; Grieser, M.; Heber, O.; Jordon-Thaden, B.; Krantz, C.; Novotný, O.; Repnow, R.; Schurig, V.; Vager, Z.; Wolf, A.; Trapp, O.; Kreckel, H.

    2015-09-01

    We have applied the method of foil-induced Coulomb Explosion Imaging (FCEI) to determine the handedness of a homochiral sample of the compound trans-2,3-dideuterooxirane C2OH2D2. We determined the compound to be of the (R, R)-econfiguration with a statistical significance of 5σ. As the molecular sample was chemically linked to the stereochemical reference standard glyceraldehyde, our assignment constitutes an independent verification of the absolute handedness of all compounds linked to this reference substance.

  17. Determination of the Absolute Configurations of Chiral Drugs Using Chiroptical Spectroscopy.

    PubMed

    Polavarapu, Prasad L

    2016-01-01

    Chiroptical spectroscopy has emerged as a promising tool for the determination of absolute configurations and predominant conformations of chiral molecules in academic laboratories. This promise has led to the adaption of chiroptical spectroscopic methods as valuable tools in chiral drug discovery research programs of the pharmaceutical industry. Most major pharmaceutical companies have invested in in-house chiroptical spectroscopy applications and reported successful outcomes. In the context of continuously increasing applications of chiroptical spectroscopy for chiral molecular structure determination, a review of recent developments and applications for chiral drugs is presented in this manuscript. PMID:27529201

  18. 3D absolute shape measurement of live rabbit hearts with a superfast two-frequency phase-shifting technique.

    PubMed

    Wang, Yajun; Laughner, Jacob I; Efimov, Igor R; Zhang, Song

    2013-03-11

    This paper presents a two-frequency binary phase-shifting technique to measure three-dimensional (3D) absolute shape of beating rabbit hearts. Due to the low contrast of the cardiac surface, the projector and the camera must remain focused, which poses challenges for any existing binary method where the measurement accuracy is low. To conquer this challenge, this paper proposes to utilize the optimal pulse width modulation (OPWM) technique to generate high-frequency fringe patterns, and the error-diffusion dithering technique to produce low-frequency fringe patterns. Furthermore, this paper will show that fringe patterns produced with blue light provide the best quality measurements compared to fringe patterns generated with red or green light; and the minimum data acquisition speed for high quality measurements is around 800 Hz for a rabbit heart beating at 180 beats per minute. PMID:23482151

  19. Absolute determination of the neutron source yield using melamine as a neutron detector

    NASA Astrophysics Data System (ADS)

    Ciechanowski, M.; Bolewski, A., Jr.; Kreft, A.

    2015-01-01

    A new approach to absolute determination of the neutron source yield is presented. It bases on the application of melamine (C3H6N6) to neutron detection combined with Monte Carlo simulations of neutron transport. Melamine has the ability to detect neutrons via 14N(n, p)14C reaction and subsequent determination of 14C content. A cross section for this reaction is relatively high for thermal neutrons (1.827 b) and much lower for fast neutrons. A concentration of 14C nuclei created in the irradiated sample of melamine can be reliably measured with the aid of the accelerator mass spectrometry (AMS). The mass of melamine sufficient for this analysis is only 10 mg. Neutron detection is supported by Monte Carlo simulations of neutron transport carried out with the use of MCNP-4C code. These simulations are aimed at computing the probability of 14C creation in the melamine sample per the source neutron. The result of AMS measurements together with results of MCNP calculations enable us to determine the number of neutrons emitted from the source during the irradiation of melamine. The proposed method was applied for determining the neutron emission from a commercial 252Cf neutron source which was independently calibrated. The measured neutron emission agreed with the certified one within uncertainty limits. The relative expanded uncertainty (k=2) of the absolute neutron source yield determination was estimated at 2.6%. Apart from calibration of radionuclide neutron sources the proposed procedure could facilitate absolute yield measurements for more complex sources. Potential applications of this methodology as it is further developed include diagnostics of inertial confinement fusion and plasma-focus experiments, calibration of neutron measurement systems at tokamaks and accelerator-based neutron sources as well as characterization of neutron fields generated in large particle detectors during collisions of hadron beams.

  20. High-resolution absolute frequency referenced fiber optic sensor for quasi-static strain sensing

    SciTech Connect

    Lam, Timothy T.-Y.; Chow, Jong H.; Shaddock, Daniel A.; Littler, Ian C. M.; Gagliardi, Gianluca; Gray, Malcolm B.; McClelland, David E.

    2010-07-20

    We present a quasi-static fiber optic strain sensing system capable of resolving signals below nanostrain from 20 mHz. A telecom-grade distributed feedback CW diode laser is locked to a fiber Fabry-Perot sensor, transferring the detected signals onto the laser. An H{sup 13}C{sup 14}N absorption line is then used as a frequency reference to extract accurate low-frequency strain signals from the locked system.

  1. Enantioselective Total Synthesis of (+)-Steenkrotin A and Determination of Its Absolute Configuration.

    PubMed

    Pan, Saiyong; Gao, Beiling; Hu, Jialei; Xuan, Jun; Xie, Hujun; Ding, Hanfeng

    2016-01-18

    The first enantioselective total synthesis of (+)-steenkrotin A has been achieved in 18 steps and 4.2 % overall yield. The key features of the strategy entail a Rh-catalyzed O-H bond insertion followed by an intramolecular carbonyl-ene reaction, two sequential SmI2 -mediated Ueno-Stork and ketyl-olefin cyclizations, and a cascade intramolecular aldol condensation/vinylogous retro-aldol/aldol process with inversion of the relative configuration at the C7 position. The absolute configuration of (+)-steenkrotin A was determined based on the stepwise construction of the stereocenters during the total synthesis. PMID:26660855

  2. Absolute radical densities in etching plasmas determined by broad-band UV absorption spectroscopy

    NASA Astrophysics Data System (ADS)

    Booth, Jean-Paul; Cunge, Gilles; Neuilly, François; Sadeghi, Nader

    1998-08-01

    Broad-band UV absorption spectroscopy was used to determine radical densities in reactive gas plasmas generated in a 13.56 MHz capacitively coupled parallel plate reactor. Five radical species were detected: 0963-0252/7/3/021/img1, CF, AlF, 0963-0252/7/3/021/img2 and 0963-0252/7/3/021/img3. Absolute (line-integrated) 0963-0252/7/3/021/img1 densities were determined in 0963-0252/7/3/021/img5 and 0963-0252/7/3/021/img6 plasmas, as were the 0963-0252/7/3/021/img1 vibrational and rotational temperatures in the latter case. In 0963-0252/7/3/021/img5 plasmas the CF radical was also detected, along with the etch products AlF (from the Al powered electrode) and 0963-0252/7/3/021/img2 (when an Si substrate was present). The fraction that 0963-0252/7/3/021/img2 comprises of the total etch products was estimated. Finally, the 0963-0252/7/3/021/img3 dimer was detected in an 0963-0252/7/3/021/img12 plasma in the presence of an Si substrate. This simple technique allows absolute concentrations of many key reactive species to be determined in reactive plasmas, without the need to analyse the complex rotational spectra of these polyatomic molecules.

  3. Radio frequency cavity analysis, measurement, and calibration of absolute Dee voltage for K-500 superconducting cyclotron at VECC, Kolkata

    NASA Astrophysics Data System (ADS)

    Som, Sumit; Seth, Sudeshna; Mandal, Aditya; Paul, Saikat; Duttagupta, Anjan

    2013-02-01

    Variable Energy Cyclotron Centre has commissioned a K-500 superconducting cyclotron for various types of nuclear physics experiments. The 3-phase radio-frequency system of superconducting cyclotron has been developed in the frequency range 9-27 MHz with amplitude and phase stability of 100 ppm and ±0.20, respectively. The analysis of the RF cavity has been carried out using 3D Computer Simulation Technology (CST) Microwave Studio code and various RF parameters and accelerating voltages ("Dee" voltage) are calculated from simulation. During the RF system commissioning, measurement of different RF parameters has been done and absolute Dee voltage has been calibrated using a CdTe X-ray detector along with its accessories and known X-ray source. The present paper discusses about the measured data and the simulation result.

  4. Absolute distance measurement by multi-heterodyne interferometry using a frequency comb and a cavity-stabilized tunable laser.

    PubMed

    Wu, Hanzhong; Zhang, Fumin; Liu, Tingyang; Balling, Petr; Qu, Xinghua

    2016-05-20

    In this paper, we develop a multi-heterodyne system capable of absolute distance measurement using a frequency comb and a tunable diode laser locked to a Fabry-Perot cavity. In a series of subsequent measurements, numerous beat components can be obtained by downconverting the optical frequency into the RF region with multi-heterodyne interferometry. The distances can be measured via the mode phases with a series of synthetic wavelengths. The comparison with the reference interferometer shows an agreement within 1.5 μm for the averages of five measurements and 2.5 μm for the single measurement, which is at the 10-8 relative precision level. PMID:27411152

  5. Radio frequency cavity analysis, measurement, and calibration of absolute Dee voltage for K-500 superconducting cyclotron at VECC, Kolkata.

    PubMed

    Som, Sumit; Seth, Sudeshna; Mandal, Aditya; Paul, Saikat; Duttagupta, Anjan

    2013-02-01

    Variable Energy Cyclotron Centre has commissioned a K-500 superconducting cyclotron for various types of nuclear physics experiments. The 3-phase radio-frequency system of superconducting cyclotron has been developed in the frequency range 9-27 MHz with amplitude and phase stability of 100 ppm and ±0.2(0), respectively. The analysis of the RF cavity has been carried out using 3D Computer Simulation Technology (CST) Microwave Studio code and various RF parameters and accelerating voltages ("Dee" voltage) are calculated from simulation. During the RF system commissioning, measurement of different RF parameters has been done and absolute Dee voltage has been calibrated using a CdTe X-ray detector along with its accessories and known X-ray source. The present paper discusses about the measured data and the simulation result. PMID:23464200

  6. Radio frequency cavity analysis, measurement, and calibration of absolute Dee voltage for K-500 superconducting cyclotron at VECC, Kolkata

    SciTech Connect

    Som, Sumit; Seth, Sudeshna; Mandal, Aditya; Paul, Saikat; Duttagupta, Anjan

    2013-02-15

    Variable Energy Cyclotron Centre has commissioned a K-500 superconducting cyclotron for various types of nuclear physics experiments. The 3-phase radio-frequency system of superconducting cyclotron has been developed in the frequency range 9-27 MHz with amplitude and phase stability of 100 ppm and {+-}0.2{sup 0}, respectively. The analysis of the RF cavity has been carried out using 3D Computer Simulation Technology (CST) Microwave Studio code and various RF parameters and accelerating voltages ('Dee' voltage) are calculated from simulation. During the RF system commissioning, measurement of different RF parameters has been done and absolute Dee voltage has been calibrated using a CdTe X-ray detector along with its accessories and known X-ray source. The present paper discusses about the measured data and the simulation result.

  7. Time dependent corrections to absolute gravity determinations in the establishment of modern gravity control

    NASA Astrophysics Data System (ADS)

    Dykowski, Przemyslaw; Krynski, Jan

    2015-04-01

    The establishment of modern gravity control with the use of exclusively absolute method of gravity determination has significant advantages as compared to the one established mostly with relative gravity measurements (e.g. accuracy, time efficiency). The newly modernized gravity control in Poland consists of 28 fundamental stations (laboratory) and 168 base stations (PBOG14 - located in the field). Gravity at the fundamental stations was surveyed with the FG5-230 gravimeter of the Warsaw University of Technology, and at the base stations - with the A10-020 gravimeter of the Institute of Geodesy and Cartography, Warsaw. This work concerns absolute gravity determinations at the base stations. Although free of common relative measurement errors (e.g. instrumental drift) and effects of network adjustment, absolute gravity determinations for the establishment of gravity control require advanced corrections due to time dependent factors, i.e. tidal and ocean loading corrections, atmospheric corrections and hydrological corrections that were not taken into account when establishing the previous gravity control in Poland. Currently available services and software allow to determine high accuracy and high temporal resolution corrections for atmospheric (based on digital weather models, e.g. ECMWF) and hydrological (based on hydrological models, e.g. GLDAS/Noah) gravitational and loading effects. These corrections are mostly used for processing observations with Superconducting Gravimeters in the Global Geodynamics Project. For the area of Poland the atmospheric correction based on weather models can differ from standard atmospheric correction by even ±2 µGal. The hydrological model shows the annual variability of ±8 µGal. In addition the standard tidal correction may differ from the one obtained from the local tidal model (based on tidal observations). Such difference at Borowa Gora Observatory reaches the level of ±1.5 µGal. Overall the sum of atmospheric and

  8. Absolute site effects in Kachchh, India, determined from aftershocks of the 2002 Bhuj earthquake.

    NASA Astrophysics Data System (ADS)

    Malagnini, L.; Mayeda, K.; Bodin, P.; Akinci, A.

    2004-12-01

    What can be learned about absolute site effects on ground motions from recordings of aftershocks at ten temporary seismic stations, none of which could be considered a "reference" (hard rock) site, and for which no geotechnical information is available? This challenge motivated our current study of Bhuj aftershocks; and our answer, briefly put, is: quite a bit. We started by constraining the regional attenuation and geometric spreading: this was the result of an earlier study [Bodin et al., BSSA 2004], the goal of which was to be able to reproduce the general character of the observations with a constrained set of stochastic synthetic ground motions. Our present work is based on the same aftershock data we used in the prior study. We first produced stable and reliable, unbiased source moment-rate spectra using the technique described by Mayeda et al., [BSSA, 2003]. With these known "absolute" source spectra, and the propagation terms we quantified in the previous study we inverted for the site response using only the largest ~200 earthquakes (M>2.8) in each of two depth ranges (0-25 km, and 20-40 km), to yield the "absolute" site terms for horizontal and vertical ground motions. We were able to obtain stable results in the 1-14 hz frequency band. The results reveal that the site terms generally share a common character: small amplifications (near unity) at the longer-period end of the pass-band, and decreases (perhaps due to attenuation or near-site scattering) at the higher frequency end. This character is evident in a similar study of earthquake ground motions in the Alps at sites on hard rock [Malagnini et al., BSSA 2004]. In contrast to Alpine hard rock sites, however, the vertical site terms at our sediment and soft-rock sites are generally rather flat and featureless. We observe differences in site response between stations which appeared to be on similar geologic conditions, and vice versa. For sites that appear to be on deep unconsolidated soils

  9. High-precision laser-assisted absolute determination of x-ray diffraction angles

    SciTech Connect

    Kubicek, K.; Braun, J.; Bruhns, H.; Crespo Lopez-Urrutia, J. R.; Mokler, P. H.; Ullrich, J.

    2012-01-15

    A novel technique for absolute wavelength determination in high-precision crystal x-ray spectroscopy recently introduced has been upgraded reaching unprecedented accuracies. The method combines visible laser beams with the Bond method, where Bragg angles ({theta} and -{theta}) are determined without any x-ray reference lines. Using flat crystals this technique makes absolute x-ray wavelength measurements feasible even at low x-ray fluxes. The upgraded spectrometer has been used in combination with first experiments on the 1s2p {sup 1}P{sub 1}{yields} 1s{sup 2} {sup 1}S{sub 0} w-line in He-like argon. By resolving a minute curvature of the x-ray lines the accuracy reaches there the best ever reported value of 1.5 ppm. The result is sensitive to predicted second-order QED contributions at the level of two-electron screening and two-photon radiative diagrams and will allow for the first time to benchmark predicted binding energies for He-like ions at this level of precision.

  10. Absolute OH density determination by laser induced fluorescence spectroscopy in an atmospheric pressure RF plasma jet

    NASA Astrophysics Data System (ADS)

    Xiong, Q.; Nikiforov, A. Yu.; Li, L.; Vanraes, P.; Britun, N.; Snyders, R.; Lu, X. P.; Leys, C.

    2012-11-01

    In this paper, the ground state OH density is measured in high pressure plasma by laser-induced fluorescence (LIF) spectroscopy. The OH density determination is based on the simulation of the intensity fraction of fluorescence from the laser-excited level of OH (A) in the total detected LIF signal. The validity of this approach is verified in an atmospheric pressure Ar + H2O plasma jet sustained by a 13.56 MHz power supply. The transition line P1 (4) from OH (A, v' = 1, J' = 3) → OH (X, v'' = 0, J'' = 4) is used for the LIF excitation. The absolute OH density is determined to be 2.5 × 1019 m-3 at 1 mm away from the jet nozzle. It corresponds to a dissociation of 0.06% of the water vapor in the working gas. Different mechanisms of OH (X) production in the core of the plasma jet are discussed and analyzed.

  11. Determination of absolute interferometric phase using the beam-amplitude ratio technique

    SciTech Connect

    Bickel, D.L.; Hensley, W.H.

    1996-03-01

    Determination of the absolute phase difference (i.e., not modulo 2{pi}) is a key problem in interferometric synthetic aperture radar (IFSAR) for topographic mapping. One way of solving this problem requires use of a technique different from the basic interferometry to resolve a `coarse` angle measurement that lies within the IFSAR ambiguity angle. The method investigated in this paper involves taking advantage of the difference in the amplitude ratio versus elevation angle that occurs when the elevation beams of the two IFSAR antennas are pointed in slightly different directions. The performance of the technique is a function of the angular separation of the two beams, the elevation beamwidth, and the symmetry of the two beam-amplitude patterns. The performance required of the technique is set by the ambiguity angle of the interferometer. This paper presents an analysis of the beam-amplitude ratio technique and shows experimental results.

  12. Determination of RW3-to-water mass-energy absorption coefficient ratio for absolute dosimetry.

    PubMed

    Seet, Katrina Y T; Hanlon, Peta M; Charles, Paul H

    2011-12-01

    The measurement of absorbed dose to water in a solid-phantom may require a conversion factor because it may not be radiologically equivalent to water. One phantom developed for the use of dosimetry is a solid water, RW3 white-polystyrene material by IBA. This has a lower mass-energy absorption coefficient than water due to high bremsstrahlung yield, which affects the accuracy of absolute dosimetry measurements. In this paper, we demonstrate the calculation of mass-energy absorption coefficient ratios, relative to water, from measurements in plastic water and RW3 with an Elekta Synergy linear accelerator (6 and 10 MV photon beams) as well as Monte Carlo modeling in BEAMnrc and DOSXYZnrc. From this, the solid-phantom-to-water correction factor was determined for plastic water and RW3. PMID:21960410

  13. Fast GPU-based absolute intensity determination for energy-dispersive X-ray Laue diffraction

    NASA Astrophysics Data System (ADS)

    Alghabi, F.; Send, S.; Schipper, U.; Abboud, A.; Pietsch, U.; Kolb, A.

    2016-01-01

    This paper presents a novel method for fast determination of absolute intensities in the sites of Laue spots generated by a tetragonal hen egg-white lysozyme crystal after exposure to white synchrotron radiation during an energy-dispersive X-ray Laue diffraction experiment. The Laue spots are taken by means of an energy-dispersive X-ray 2D pnCCD detector. Current pnCCD detectors have a spatial resolution of 384 × 384 pixels of size 75 × 75 μm2 each and operate at a maximum of 400 Hz. Future devices are going to have higher spatial resolution and frame rates. The proposed method runs on a computer equipped with multiple Graphics Processing Units (GPUs) which provide fast and parallel processing capabilities. Accordingly, our GPU-based algorithm exploits these capabilities to further analyse the Laue spots of the sample. The main contribution of the paper is therefore an alternative algorithm for determining absolute intensities of Laue spots which are themselves computed from a sequence of pnCCD frames. Moreover, a new method for integrating spectral peak intensities and improved background correction, a different way of calculating mean count rate of the background signal and also a new method for n-dimensional Poisson fitting are presented.We present a comparison of the quality of results from the GPU-based algorithm with the quality of results from a prior (base) algorithm running on CPU. This comparison shows that our algorithm is able to produce results with at least the same quality as the base algorithm. Furthermore, the GPU-based algorithm is able to speed up one of the most time-consuming parts of the base algorithm, which is n-dimensional Poisson fitting, by a factor of more than 3. Also, the entire procedure of extracting Laue spots' positions, energies and absolute intensities from a raw dataset of pnCCD frames is accelerated by a factor of more than 3.

  14. Using star tracks to determine the absolute pointing of the Fluorescence Detector telescopes of the Pierre Auger Observatory

    SciTech Connect

    De Donato, Cinzia; Sanchez, Federico; Santander, Marcos; Natl.Tech.U., San Rafael; Camin, Daniel; Garcia, Beatriz; Grassi, Valerio; /Milan U. /INFN, Milan

    2005-05-01

    To accurately reconstruct a shower axis from the Fluorescence Detector data it is essential to establish with high precision the absolute pointing of the telescopes. To d that they calculate the absolute pointing of a telescope using sky background data acquired during regular data taking periods. The method is based on the knowledge of bright star's coordinates that provide a reliable and stable coordinate system. it can be used to check the absolute telescope's pointing and its long-term stability during the whole life of the project, estimated in 20 years. They have analyzed background data taken from January to October 2004 to determine the absolute pointing of the 12 telescopes installed both in Los Leones and Coihueco. The method is based on the determination of the mean-time of the variance signal left by a star traversing a PMT's photocathode which is compared with the mean-time obtained by simulating the track of that star on the same pixel.

  15. Problems determining relative and absolute ages using the small crater population

    NASA Astrophysics Data System (ADS)

    Xiao, Zhiyong; Strom, Robert G.

    2012-07-01

    The small crater populations (diameter smaller than 1 km) are widely used to date planetary surfaces. The reliability of small crater counts is tested by counting small craters at several young and old lunar surfaces, including Mare Nubium and craters Alphonsus, Tycho and Giordano Bruno. Based on high-resolution images from both the Lunar Reconnaissance Orbiter Camera and Kaguya Terrain Camera, small craters in two different diameter ranges are counted for each counting area. Large discrepancies exist in both the cumulative (absolute model ages) and relative plots for the two different size ranges of the same counting areas. The results indicate that dating planetary surfaces using small crater populations is highly unreliable because the contamination of secondaries may invalidate the results of small crater counts. A comparison of the size-frequency distributions of the small crater populations and impact ejected boulders around fresh lunar craters shows the same upturn as typical martian secondaries, which supports the argument that secondaries dominate the small crater populations on the Moon and Mars. Also, the size-frequency distributions of small rayed lunar and martian craters of probable primary origin are similar to that of the Population 2 craters on the inner Solar System bodies post-dating Late Heavy Bombardment. Dating planetary surfaces using the small crater populations requires the separation of primaries from secondaries which is extremely difficult. The results also show that other factors, such as different target properties and the subjective identification of impact craters by different crater counters, may also affect crater counting results. We suggest that dating planetary surfaces using small crater populations should be with highly cautious.

  16. Drug Treated Schizophrenia, Schizoaffective and Bipolar Disorder Patients Evaluated by qEEG Absolute Spectral Power and Mean Frequency Analysis

    PubMed Central

    Wix-Ramos, Richard; Moreno, Xiomara; Capote, Eduardo; González, Gilbert; Uribe, Ezequiel

    2014-01-01

    Objective Research of electroencephalograph (EEG) power spectrum and mean frequency has shown inconsistent results in patients with schizophrenic, schizoaffective and bipolar disorders during medication when compared to normal subjects thus; the characterization of these parameters is an important task. Methods We applied quantitative EEG (qEEG) to investigate 38 control, 15 schizophrenic, 7 schizoaffective and 11 bipolar disorder subjects which remaine under the administration of psychotropic drugs (except control group). Absolute spectral power (ASP), mean frequency and hemispheric electrical asymmetry were measured by 19 derivation qEEG. Group mean values were compared with non parametrical Mann-Whitney test and spectral EEG maps with z-score method at p < 0.05. Results Most frequent drug treatments for schizophrenic patients were neuroleptic+antiepileptic (40% of cases) or 2 neuroleptics (33.3%). Schizoaffective patients received neuroleptic+benzodiazepine (71.4%) and for bipolar disorder patients neuroleptic+antiepileptic (81.8%). Schizophrenic (at all derivations except for Fp1, Fp2, F8 and T6) and schizoaffective (only at C3) show higher values of ASP (+57.7% and +86.1% respectively) compared to control group. ASP of bipolar disorder patients did not show differences against control group. The mean frequency was higher at Fp1 (+14.2%) and Fp2 (+17.4%) in bipolar disorder patients than control group, but no differences were found in frequencies between schizophrenic or schizoaffective patients against the control group. Majority of spectral differences were found at the left hemisphere in schizophrenic and schizoaffective but not in bipolar disorder subjects. Conclusion The present report contributes to characterize quantitatively the qEEG in drug treated schizophrenic, schizoaffective or bipolar disorder patients. PMID:24851121

  17. Spectrofluorimetric determination of aluminum ions via complexation with luteolin in absolute ethanol.

    PubMed

    Sun, Jinyu; Wu, You; Xiao, Dan; Lin, Xia; Li, Hui

    2014-08-01

    An optimized and validated spectrofluorimetric method has been developed for the rapid determination of aluminum in absolute ethanol. The method is based on the chelation of aluminum and luteolin which results in a complex exhibiting an intense emission signal. The characterization of Al-luteolin complex was studied using ultraviolet-visible spectrometry, infrared spectrometry, fluorescence and mass spectrometry. The complex stoichiometry ratio of aluminum:luteolin was 1:2. The fluorescence of the complex was monitored at an emission wavelength of 545 nm with excitation at 518 nm. The linear concentration range was 6.5 × 10(-7) to 4.0 × 10(-5)  M with a correlation coefficient of r = 0.998. The detection limit was 5.0 × 10(-7)  M. The method was appropriately validated and yielded relative standard deviations of < 2.3% (n = 5), which was considered acceptable. The method was successfully applied in the determination of aluminum in river water, skin care products and pharmaceutical samples. PMID:24039003

  18. Systematic determination of absolute absorption cross-section of individual carbon nanotubes

    PubMed Central

    Liu, Kaihui; Hong, Xiaoping; Choi, Sangkook; Jin, Chenhao; Capaz, Rodrigo B.; Kim, Jihoon; Wang, Wenlong; Bai, Xuedong; Louie, Steven G.; Wang, Enge; Wang, Feng

    2014-01-01

    Optical absorption is the most fundamental optical property characterizing light–matter interactions in materials and can be most readily compared with theoretical predictions. However, determination of optical absorption cross-section of individual nanostructures is experimentally challenging due to the small extinction signal using conventional transmission measurements. Recently, dramatic increase of optical contrast from individual carbon nanotubes has been successfully achieved with a polarization-based homodyne microscope, where the scattered light wave from the nanostructure interferes with the optimized reference signal (the reflected/transmitted light). Here we demonstrate high-sensitivity absorption spectroscopy for individual single-walled carbon nanotubes by combining the polarization-based homodyne technique with broadband supercontinuum excitation in transmission configuration. To our knowledge, this is the first time that high-throughput and quantitative determination of nanotube absorption cross-section over broad spectral range at the single-tube level was performed for more than 50 individual chirality-defined single-walled nanotubes. Our data reveal chirality-dependent behaviors of exciton resonances in carbon nanotubes, where the exciton oscillator strength exhibits a universal scaling law with the nanotube diameter and the transition order. The exciton linewidth (characterizing the exciton lifetime) varies strongly in different nanotubes, and on average it increases linearly with the transition energy. In addition, we establish an empirical formula by extrapolating our data to predict the absorption cross-section spectrum for any given nanotube. The quantitative information of absorption cross-section in a broad spectral range and all nanotube species not only provides new insight into the unique photophysics in one-dimensional carbon nanotubes, but also enables absolute determination of optical quantum efficiencies in important

  19. An absolute instrument for determination of the speed of sound in water.

    PubMed

    Li, Zhiwei; Zhu, Junchao; Li, Tao; Zhang, Baofeng

    2016-05-01

    An apparatus for the absolute determination of the sound speed in water based on the time-of-flight technique is described. The time measurement is realized by hardware circuits and the distance measurement by a double-beam plane-mirror interferometer. A highly accurate time chip, with a resolution of approximately 90 ps, is employed for time measurements. The acoustic path length is adjustable and can be measured directly. Two transducers are used for transmitting and receiving ultrasonic signals without reflection. The transducers are immersed in a thermostatic vessel that maintains bath temperature with high stability. The speed of sound in pure water was measured at ambient pressure and at the temperatures 308 K, 303 K, 298 K, and 293 K. The achieved measurement uncertainties are 2 mK for temperature and 0.045 m/s for speed of sound. The results are compared to data from the literature, equation of state models, and measurements by two commercial sensors in the same experiment, showing excellent agreement among them. PMID:27250470

  20. Determinants of relative and absolute concentration indices: evidence from 26 European countries

    PubMed Central

    2013-01-01

    Introduction The aim of publicly-provided health care is generally not only to produce health, but also to decrease variation in health by socio-economic status. The aim of this study is to measure to what extent this goal has been obtained in various European countries and evaluate the determinants of inequalities within countries, as well as cross-country patterns with regard to different cultural, institutional and social settings. Methods The data utilized in this study provides information on 440,000 individuals in 26 European countries and stem from The European Union Statistics on Income and Living Conditions (EU-SILC) collected in 2007. As measures of income-related inequality in health both the relative concentration indices and the absolute concentration indices are calculated. Further, health inequality in each country is decomposed into individual-level determinants and cross-country comparisons are made to shed light on social and institutional determinants. Results Income-related health inequality favoring the better-off is observed for all the 26 European countries. In terms of within-country determinants inequality is mainly explained by income, age, education, and activity status. However, the degree of inequality and contribution of each determinant to inequality varies considerably between countries. Aggregate bivariate linear regressions show that there is a positive association between health-income inequality in Europe and public expenditure on education. Furthermore, a negative relationship between health-income inequality and income inequality was found when individual employee cash income was used in the health-concentration measurement. Using that same income measure, health-income inequality was found to be higher in the Nordic countries than in other areas, but this result is sensitive to the income measure chosen. Conclusions The findings indicate that institutional determinants partly explain income-related health inequalities across

  1. Asymmetric total synthesis of (-)-lundurine B and determination of its absolute stereochemistry.

    PubMed

    Nakajima, Masaya; Arai, Shigeru; Nishida, Atsushi

    2015-04-01

    A total synthesis of the Kopsia tenuis alkaloid (-)-lundurine B has been achieved. A quaternary chiral carbon has been created by an asymmetric deprotonation using a symmetric spiro cyclohexanone intermediate with a chiral lithium amide. The hexacyclic skeleton was sequentially constructed through metal-mediated reactions. The absolute stereochemistry of intermediate 5 has been unambiguously established by X-ray crystallographic analysis. This is the first description of the absolute stereochemistry of Kopsia tenuis alkaloids based on chemical synthesis. PMID:25601233

  2. Absolute and relative emission spectroscopy study of 3 cm wide planar radio frequency atmospheric pressure bio-plasma source

    NASA Astrophysics Data System (ADS)

    Deng, Xiaolong; Nikiforov, Anton Yu; Ionita, Eusebiu-Rosini; Dinescu, Gheorghe; Leys, Christophe

    2015-08-01

    The dynamics of low power atmospheric pressure radio frequency discharge generated in Ar gas in long gap of 3 cm is investigated. This plasma source is characterized and analyzed for possible large scale biomedical applications where low gas temperature and potential-less effluent are required. The discharge forms a homogenous glow-like afterglow in ambient air at input power of 30 W with low gas temperature of 330 K, which is desirable in biomedical applications. With absolute calibrated spectroscopy of the discharge, electron density of 0.4 × 1018 m-3 and electron temperature of 1.5 eV are obtained from continuum Bremsstrahlung radiation of the source. Time and spatial resolved emission spectroscopy is used to analyze discharge generation mechanism and active species formation. It is found that discharge dynamics strongly correlates with the discharge current waveform. Strong Ar(2p) excited states emission is observed nearby the electrodes surface on a distance up to 200 μm in the plasma sheath region at 10 ns after the current peak, whereas OH(A) emission is uniform along of the interelectrode gap.

  3. Easy Absolute Values? Absolutely

    ERIC Educational Resources Information Center

    Taylor, Sharon E.; Mittag, Kathleen Cage

    2015-01-01

    The authors teach a problem-solving course for preservice middle-grades education majors that includes concepts dealing with absolute-value computations, equations, and inequalities. Many of these students like mathematics and plan to teach it, so they are adept at symbolic manipulations. Getting them to think differently about a concept that they…

  4. Absolute masses and radii determination in multiplanetary systems without stellar models

    NASA Astrophysics Data System (ADS)

    Almenara, J. M.; Díaz, R. F.; Mardling, R.; Barros, S. C. C.; Damiani, C.; Bruno, G.; Bonfils, X.; Deleuil, M.

    2015-11-01

    The masses and radii of extrasolar planets are key observables for understanding their interior, formation and evolution. While transit photometry and Doppler spectroscopy are used to measure the radii and masses respectively of planets relative to those of their host star, estimates for the true values of these quantities rely on theoretical models of the host star which are known to suffer from systematic differences with observations. When a system is composed of more than two bodies, extra information is contained in the transit photometry and radial velocity data. Velocity information (finite speed-of-light, Doppler) is needed to break the Newtonian MR-3 degeneracy. We performed a photodynamical modelling of the two-planet transiting system Kepler-117 using all photometric and spectroscopic data available. We demonstrate how absolute masses and radii of single-star planetary systems can be obtained without resorting to stellar models. Limited by the precision of available radial velocities (38 m s-1), we achieve accuracies of 20 per cent in the radii and 70 per cent in the masses, while simulated 1 m s-1 precision radial velocities lower these to 1 per cent for the radii and 2 per cent for the masses. Since transiting multiplanet systems are common, this technique can be used to measure precisely the mass and radius of a large sample of stars and planets. We anticipate these measurements will become common when the TESS and PLATO mission provide high-precision light curves of a large sample of bright stars. These determinations will improve our knowledge about stars and planets, and provide strong constraints on theoretical models.

  5. 3D absolute hypocentral determination - 13 years of seismicity in Ecuadorian subduction zone

    NASA Astrophysics Data System (ADS)

    Font, Yvonne; Segovia, Monica; Theunissen, Thomas

    2010-05-01

    of azimuthal coverage, record frequency and signal quality. Then, we define 5 domains: Offshore/coast, North-Andean margin, Volcanic chain, Southern Ecuador, and a domain deeper than 50 km. We process earthquake location only if at least 3 proximal stations exist in the event's domain. This data selection allows providing consistent quality location. The third step consists in improving the 3D MAXI technique that is well adapted to perform absolute earthquake location in velocity model presenting strong lateral Vp heterogeneities. The resulting catalogue allows specifying the deformation in the subduction system. All seismicity previously detected before trench occurs indeed between the trench and the coastal range. South of 0°, facing the subducting Carnegie Ridge, the seismicity aligns along the interplate seismogenic zone between an updip limit shallower than ~8 km and a downdip limit that reaches up to 50 km depth. The active seismogenic zone is interrupted by a gap that extends right beneath the coastal range. At these latitudes, a diffuse intraplate deformation also affects the subducting plate, probably induced by the locally thickened lithosphere flexure. Between the trench and the coast, earthquake distribution clearly defines a gap, which size is comparable to the 1942 M7.9 asperity (ellipse of axes ~55/35 km). A slab is clearly defines and dips around 25 to 30°. The slab seismicity is systematically interrupted between 100-170 km, approximately beneath the volcanic chain. North of 0°, i.e. in the megathrust earthquake domain, the interseismic activity is clearly reduced. The interplate distribution seems to gather along alignments perpendicular to the trench attesting probably of the margin segmentation. The North Andean overriding margin is undergoing active deformation, especially at the location where the Andean Chain strike changes of direction. At these latitudes, no earthquake occurs deeper than 100 km depth.

  6. Determination of the Absolute Configuration of the Pseudo-Symmetric Natural Product Elatenyne by the Crystalline Sponge Method.

    PubMed

    Urban, Sylvia; Brkljača, Robert; Hoshino, Manabu; Lee, Shoukou; Fujita, Makoto

    2016-02-01

    Elatenyne is a marine natural product that was isolated in 1986. Despite its simple 2,2'-bifuranyl backbone, its relative structure was only recently determined. The absolute configuration of elatenyne has still not been unequivocally confirmed because of its pseudo-meso core structure, which results in a specific rotation, [α]D  , of almost zero. In this work, the structure of natural elatenyne was determined by the crystalline sponge method and the use of a porous coordination network (a crystalline sponge) capable of absorbing organic guests; in the sponge, the absorbed guests are ordered and crystallographically observable. The crystalline sponge could differentiate between the two very similar alkyl side chains, and the absolute structure of elatenyne was thus reliably determined. The total amount required for the experiments was only approximately 100 μg, and the majority (95 μg) could be recovered after the experiments. PMID:26880368

  7. Determination of the absolute isotopic composition and Atomic Weight of a reference sample of natural iron

    NASA Astrophysics Data System (ADS)

    Taylor, P. D. P.; Maeck, R.; de Bièvre, P.

    1992-11-01

    Absolute values have been obtained by means of thermal ionisation mass spectrometry for the iron isotope abundance ratios of a sample of metallic iron of natural isotopic composition. This was achieved by calibrating the mass spectrometric measurement procedure using five different synthetic isotope mixtures, prepared from carefully characterised enriched isotope carrier compounds, viz. 54Fe2O3 and 56Fe2O3. These mixtures were made up at three different n(54Fe)/n(56Fe) ratios, covering a ratio range of more than two orders of magnitude, in order to determine the extent of the isotope fractionation in the ion source. Two mixtures bracket the natural ratio, two mixtures have ratio values approximating to unity, and one mixture has a ratio of about 10. The total relative uncertainty on the ratio values of the mixtures varies between 2 and 7 × 10-4 (2s). Three different mass spectrometric measurement procedures were developed, all using a silica-gel/boric acid ionisation enhancer. Measurements were carried out on two different instruments. The n(54Fe)/n(56Fe) ratio of the synthetic mixtures and of the natural iron isotopic reference material (IRM) were measured using a mass spectrometer with Faraday detector. Both the n(57Fe)/n(56Fe) and n(58Fe)/n(56Fe) ratios of the natural iron IRM were determined using the same instrument but operated at a higher ionisation temperature (1430°C instead of 1350°C) and using an internal normalisation procedure. For the determination of the abundances of the minor isotopes in the enriched isotope carrier compounds, an instrument equipped with a calibrated ion counting device was used and the ionisation temperature was 1150°C. Using the latter instrument and method, the n(54Fe)/n(56Fe) ratio of the IRM was found to a gree within 4 × 10-5 with the calibrated value of the Faraday measurements, indicating that experimental conditions were well controlled in both cases. Compared to the current IUPAC data (Atomic Weights of the Elements

  8. Absolute frequency measurement of 1S0(F = 1/2)-3P0(F = 1/2) transition of 171Yb atoms in a one-dimensional optical lattice at KRISS

    NASA Astrophysics Data System (ADS)

    Park, Chang Yong; Yu, Dai-Hyuk; Lee, Won-Kyu; Eon Park, Sang; Kim, Eok Bong; Lee, Sun Kyung; Cho, Jun Woo; Yoon, Tai Hyun; Mun, Jongchul; Jong Park, Sung; Kwon, Taeg Yong; Lee, Sang-Bum

    2013-04-01

    We measured the absolute frequency of the optical clock transition 1S0(F = 1/2)-3P0(F = 1/2) of 171Yb atoms confined in a one-dimensional optical lattice and it was determined to be 518 295 836 590 863.5(8.1) Hz. The frequency was measured against Terrestrial Time (TT; the SI second on the geoid) using an optical frequency comb of which the frequency was phase-locked to an H-maser as a flywheel oscillator traceable to TT. The magic wavelength was also measured as 394 798.48(79) GHz. The results are in good agreement with two previous measurements of other institutes within the specified uncertainty of this work.

  9. 40 CFR 93.104 - Frequency of conformity determinations.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Frequency of conformity determinations..., Funded or Approved Under Title 23 U.S.C. or the Federal Transit Laws § 93.104 Frequency of conformity... implementation plan. (b) Frequency of conformity determinations for transportation plans. (1) Each...

  10. 40 CFR 93.104 - Frequency of conformity determinations.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Frequency of conformity determinations..., Funded or Approved Under Title 23 U.S.C. or the Federal Transit Laws § 93.104 Frequency of conformity... implementation plan. (b) Frequency of conformity determinations for transportation plans. (1) Each...

  11. 40 CFR 93.104 - Frequency of conformity determinations.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Frequency of conformity determinations..., Funded or Approved Under Title 23 U.S.C. or the Federal Transit Laws § 93.104 Frequency of conformity... implementation plan. (b) Frequency of conformity determinations for transportation plans. (1) Each...

  12. Determination of the absolute configuration of mono-saccharides in complex carbohydrates by capillary G.L.C.

    PubMed

    Gerwig, G J; Kamerling, J P; Vliegenthart, J F

    1979-12-01

    The absolute configuration of neutral monosaccharides, 2-acetamido-2-deoxy sugars, and uronic acids can be determined by capillary g.l.c. on SE-30 after glycosidation with (-)-2-butanol and protection of the remaining polar groups. The method is illustrated by application to mixtures of the constituent sugars of the capsular polysaccharide from Klebsiella type 57, alpha 1-acid glycoprotein, mucus glycoproteins, and the methylated, acidic polysaccharide from the coccoliths of Emiliania huxleyi (Lohmann) Kamptner. PMID:519653

  13. Studies Culminating in the Total Synthesis and Determination of the Absolute Configuration of (-)-Saudin

    PubMed Central

    Boeckman, Robert K.; del Rosario Ferreira, Maria Rico; Mitchell, Lorna H.; Shao, Pengcheng; Neeb, Michael J.; Fang, Yue

    2011-01-01

    A full account of studies that culminated in the total synthesis of both antipodes and the assignment of its absolute configuration of Saudin, a hypoglycemic natural product. Two approaches are described, the first proceeding though bicyclic lactone intermediates and related second monocyclic esters. The former was obtained via asymmetric Diels-Alder cycloaddition and the latter by an asymmetric annulation protocol. Both approaches employ a Lewis acid promoted Claisen rearrangement, with the successful approach taking advantage of bidentate chelation to control the facial selectivity of the key Claisen rearrangement PMID:22523435

  14. Absolute distance measurements by variable wavelength interferometry

    NASA Astrophysics Data System (ADS)

    Bien, F.; Camac, M.; Caulfield, H. J.; Ezekiel, S.

    1981-02-01

    This paper describes a laser interferometer which provides absolute distance measurements using tunable lasers. An active feedback loop system, in which the laser frequency is locked to the optical path length difference of the interferometer, is used to tune the laser wavelengths. If the two wavelengths are very close, electronic frequency counters can be used to measure the beat frequency between the two laser frequencies and thus to determine the optical path difference between the two legs of the interferometer.

  15. Monte Carlo calculations for absolute dosimetry to determine machine outputs for proton therapy fields

    PubMed Central

    Paganetti, Harald

    2008-01-01

    The prescribed dose in radiation therapy has to be converted into machine monitor units for patient treatment. This is done routinely for each spread-out Bragg peak (SOBP) field either by calibration measurements, by using analytical algorithms or by relying on empirical data. At the Northeast Proton Therapy Center, a monitor unit corresponds to a fixed amount of charge collected in a segmented transmission ionization chamber inside the treatment head. The goal of this work was to use a detailed Monte Carlo model of the treatment head to calculate the dose delivered to the patient as a function of ionization chamber reading, i.e. to yield absolute dose in patients in terms of machine monitor units. The results show excellent agreement with measurements. For 50 SOBP fields considered in this study, the mean absolute difference between the experimental and the calculated value is 1.5%, where ~50% of the fields agree within 1%. This is within the uncertainties of the data. The Monte Carlo method has advantages over analytical algorithms because it takes into account scattered and secondary radiation, does not rely on empirical parameters, and provides a tool to study the influence of parts of the treatment head on the ionization chamber reading. Compared to experimental methods the Monte Carlo method has the advantage of being able to verify the dose in the patient geometry. PMID:16723767

  16. The realization of the dipole (γ, γ) method and its application to determine the absolute optical oscillator strengths of helium

    PubMed Central

    Xu, Long-Quan; Liu, Ya-Wei; Kang, Xu; Ni, Dong-Dong; Yang, Ke; Hiraoka, Nozomu; Tsuei, Ku-Ding; Zhu, Lin-Fan

    2015-01-01

    The dipole (γ, γ) method, which is the inelastic x-ray scattering operated at a negligibly small momentum transfer, is proposed and realized to determine the absolute optical oscillator strengths of the vanlence-shell excitations of atoms and molecules. Compared with the conventionally used photoabsorption method, this new method is free from the line saturation effect, which can seriously limit the accuracies of the measured photoabsorption cross sections for discrete transitions with narrow natural linewidths. Furthermore, the Bethe-Born conversion factor of the dipole (γ, γ) method varies much more slowly with the excitation energy than does that of the dipole (e, e) method. Absolute optical oscillator strengths for the excitations of 1s2 → 1 snp(n = 3 − 7) of atomic helium have been determined using the high-resolution dipole (γ, γ) method, and the excellent agreement of the present measurements with both those measured by the dipole (e, e) method and the previous theoretical calculations indicates that the dipole (γ, γ) method is a powerful tool to measure the absolute optical oscillator strengths of the valence-shell excitations of atoms and molecules. PMID:26678298

  17. Vibrational frequencies and structural determination of tetrafluoroformaldazine.

    PubMed

    Jensen, James O

    2004-09-01

    The normal mode frequencies and corresponding vibrational assignments of tetrafluoroformaldazine (F(2)CNNCF(2)) are examined theoretically using the Gaussian98 set of quantum chemistry codes. Each of the vibrational modes was assigned to one of nine types of motion predicted by a group theoretical analysis (C-F stretch, C[triple bond]N stretch, N-N stretch, C=C-N bend, CF(2) wag, CF(2) rock CF(2) scissors, CF(2) twist, and C=N-N=C torsion) utilizing the C(2h) symmetry of the molecule. Uniform scaling factors was derived for each type of motion. Predicted infrared and Raman intensities are reported. PMID:15294242

  18. Absolute frequency measurement of the ^1S0<->^3P0 clock transition at 578.4 nm in ytterbium

    NASA Astrophysics Data System (ADS)

    Hoyt, Chad; Barber, Zeb; Oates, Chris; Fortier, Tara; Diddams, Scott

    2005-05-01

    We report the first precision absolute frequency measurements of the highly forbidden (6s^2)^1S0<->(6s6p)^3P0 optical clock transition at 578.4 nm in two odd isotopes of ytterbium. Atoms are cooled to tens of microkelvins in two successive stages of laser cooling and magneto-optical trapping that use transitions at 398.9 nm and 555.8 nm, respectively. The resulting trapped atomic cloud is irradiated with excitation light at 578.4 nm and absorption is detected by monitoring trapped atom depletion. With the laser on resonance, we demonstrate trap depletions of more than 80 % relative to the off-resonance case. Absolute frequency measurements are made for ^171Yb (I=1/2) and ^173Yb (I=5/2) with an uncertainty of 4.4 kHz using a femtosecond-laser frequency comb calibrated by the NIST cesium fountain clock. The natural linewidth of these J=0 to J=0 transitions is ˜10 mHz, making them well-suited to support a new generation of optical atomic clocks based on confinement in an optical lattice. Lattice-based optical clocks have the potential to surpass the performance of the best current atomic clocks by orders of magnitude. The accurate ytterbium frequency knowledge presented here (nearly a million-fold reduction in uncertainty) will greatly expedite Doppler- and recoil-free lattice spectroscopy.

  19. Absolute polarity determination of teeth cementum by phase sensitive second harmonic generation microscopy.

    PubMed

    Aboulfadl, Hanane; Hulliger, Jürg

    2015-10-01

    The absolute sign of local polarity in relation to the biological growth direction has been investigated for teeth cementum using phase sensitive second harmonic generation microscopy (PS-SHGM) and a crystal of 2-cyclooctylamino-5-nitropyridine (COANP) as a nonlinear optic (NLO) reference material. A second harmonic generation (SHG) response was found in two directions of cementum: radial (acellular extrinsic fibers that are oriented more or less perpendicular to the root surface) and circumferential (cellular intrinsic fibers that are oriented more or less parallel to the surface). A mono-polar state was demonstrated for acellular extrinsic cementum. However, along the different parts of cementum in circumferential direction, two corresponding domains were observed featuring an opposite sign of polarity indicative for a bi-polar microscopic state of cellular intrinsic cementum. The phase information showed that the orientation of radial collagen fibrils of cementum is regularly organized with the donor (D) groups pointing to the surface. Circumferential collagen molecules feature orientational disorder and are oriented up and down in random manner showing acceptor or donor groups at the surface of cementum. Considering that the cementum continues to grow in thickness throughout life, we can conclude that the cementum is growing circumferentially in two opposite directions and radially in one direction. A Markov chain type model for polarity formation in the direction of growth predicts D-groups preferably appearing at the fiber front. PMID:26297858

  20. Unambiguous Determination of the Absolute Configuration of Dimeric Stilbene Glucosides from the Rhizomes of Gnetum africanum.

    PubMed

    Buffeteau, Thierry; Cavagnat, Dominique; Bisson, Jonathan; Marchal, Axel; Kapche, Gilbert D; Battistini, Ilaria; Da Costa, Gregory; Badoc, Alain; Monti, Jean-Pierre; Mérillon, Jean-Michel; Waffo-Téguo, Pierre

    2014-08-22

    Dimeric stilbene glucosides 1-3 [two diastereomers of (-)-gnemonoside A (1a and 1b), (-)-gnemonoside C (2), and (-)-gnemonoside D (3)] as well as a mixture of the two enantiomers of gnetin C (4) were isolated from the rhizomes of Gnetum africanum. The two enantiomers of gnetin C, (+)-4 and (-)-4, were obtained from the aglycones of 1a and 1b, respectively. The configurations of these stilbenoids were investigated by NMR and vibrational circular dichroism (VCD) experiments. The absolute configurations of (-)-1a, (-)-2, (-)-3, and (-)-4 were established as 7aS,8aS by VCD spectroscopy in combination with density functional theory calculations. The antiamyloidogenic activity of the isolated stilbenes was also evaluated versus beta-amyloid fibrils. The four glucosides of gnetin C (1a, 1b, 2, and 3) were found to be the most active compounds, with inhibition percentages of 56, 56, 58, and 54 at 10 μM, respectively. PMID:25093453

  1. Absolute determination of the gelling point of gelatin under quasi-thermodynamic equilibrium.

    PubMed

    Bellini, Franco; Alberini, Ivana; Ferreyra, María G; Rintoul, Ignacio

    2015-05-01

    Thermodynamic studies on phase transformation of biopolymers in solution are useful to understand their nature and to evaluate their technological potentials. Thermodynamic studies should be conducted avoiding time-related phenomena. This condition is not easily achieved in hydrophilic biopolymers. In this contribution, the simultaneous effects of pH, salt concentration, and cooling rate (Cr) on the folding from random coil to triple helical collagen-like structures of gelatin were systematically studied. The phase transformation temperature at the absolute invariant condition of Cr = 0 °C/min (T(T)Cr=0) ) is introduced as a conceptual parameter to study phase transformations in biopolymers under quasi-thermodynamic equilibrium and avoiding interferences coming from time-related phenomena. Experimental phase diagrams obtained at different Cr are presented. The T(T)(Cr=0) compared with pH and TT(Cr=0) compared with [NaCl] diagram allowed to explore the transformation process at Cr = 0 °C/min. The results were explained by electrostatic interactions between the biopolymers and its solvation milieu. PMID:25832543

  2. An absolute method for determination of misalignment of an immersion ultrasonic transducer.

    PubMed

    Narayanan, M M; Singh, Narender; Kumar, Anish; Babu Rao, C; Jayakumar, T

    2014-12-01

    An absolute methodology has been developed for quantification of misalignment of an ultrasonic transducer using a corner-cube retroreflector. The amplitude based and the time of flight (TOF) based C-scans of the reflector are obtained for various misalignments of the transducer. At zero degree orientation of the transducer, the vertical positions of the maximum amplitude and the minimum TOF in the C-scan coincide. At any other orientation of the transducer with the horizontal plane, there is a vertical shift in the position of the maximum amplitude with respect to the minimum TOF. The position of the minimum (TOF) remains the same irrespective of the orientation of the transducer and hence is used as a reference for any misalignment of the transducer. With the measurement of the vertical shift and the horizontal distance between the transducer and the vertex of the reflector, the misalignment of the transducer is quantified. Based on the methodology developed in the present study, retroreflectors are placed in the Indian 500MWe Prototype Fast Breeder Reactor for assessment of the orientation of the ultrasonic transducer prior to the under-sodium ultrasonic scanning for detection of any protrusion of the subassemblies. PMID:25041979

  3. Evaluation of a commercial integrating sphere setup for the determination of absolute photoluminescence quantum yields of dilute dye solutions.

    PubMed

    Würth, Christian; Lochmann, Cornelia; Spieles, Monika; Pauli, Jutta; Hoffmann, Katrin; Schüttrigkeit, Tanja; Franzl, Thomas; Resch-Genger, Ute

    2010-07-01

    The commercial availability of stand-alone setups for the determination of absolute photoluminescence quantum yields (Phi(f)) in conjunction with the increasing use of integrating sphere accessories for spectrofluorometers is expected to have a considerable influence not only on the characterization of chromophore systems for use in optical and opto-electronic devices, but also on the determination of this key parameter for (bio)analytically relevant dyes and functional luminophores. Despite the huge potential of systems measuring absolute Phi(f) values and the renewed interest in dependable data, evaluated protocols for even the most elementary case, the determination of the fluorescence quantum yield of transparent dilute solutions of small organic dyes with integrating sphere methods, are still missing. This encouraged us to evaluate the performance and sources of uncertainty of a simple commercial integrating sphere setup with dilute solutions of two of the best characterized fluorescence quantum yield standards, quinine sulfate dihydrate and rhodamine 101, strongly differing in spectral overlap between absorption and emission. Special attention is dedicated to illustrate common pitfalls of this approach, thereby deriving simple procedures to minimize measurement uncertainties and improve the comparability of data for the broad community of users of fluorescence techniques. PMID:20615286

  4. Tunable cw UV laser with <35 kHz absolute frequency instability for precision spectroscopy of Sr Rydberg states.

    PubMed

    Bridge, Elizabeth M; Keegan, Niamh C; Bounds, Alistair D; Boddy, Danielle; Sadler, Daniel P; Jones, Matthew P A

    2016-02-01

    We present a solid-state laser system that generates over 200 mW of continuous-wave, narrowband light, tunable from 316.3 nm - 317.7 nm and 318.0 nm - 319.3 nm. The laser is based on commercially available fiber amplifiers and optical frequency doubling technology, along with sum frequency generation in a periodically poled stoichiometric lithium tantalate crystal. The laser frequency is stabilized to an atomic-referenced high finesse optical transfer cavity. Using a GPS-referenced optical frequency comb we measure a long term frequency instability of < 35 kHz for timescales between 10(-3) s and 10(3) s. As an application we perform spectroscopy of Sr Rydberg states from n = 37 - 81, demonstrating mode-hop-free scans of 24 GHz. In a cold atomic sample we measure Doppler-limited linewidths of 350 kHz. PMID:26906804

  5. Atom-chip based quantum gravimetry for the precise determination of absolute local gravity

    NASA Astrophysics Data System (ADS)

    Abend, S.

    2015-12-01

    We present a novel technique for the precise measurement of absolute local gravity based on cold atom interferometry. Atom interferometry utilizes the interference of matter waves interrogated by laser light to read out inertial forces. Today's generation of these devices typically operate with test mass samples, that consists of ensembles of laser cooled atoms. Their performance is limited by the velocity spread and finite-size of the test masses that impose systematic uncertainties at the level of a few μGal. Rather than laser cooled atoms we employ quantum degenerate ensembles, so called Bose-Einstein condensates, as ultra-sensitive probes for gravity. These sources offer unique properties in temperature as well as in ensemble size that will allow to overcome the current limitations with the next generation of sensors. Furthermore, atom-chip technologies offer the possibility to generate Bose-Einstein condensates in a fast and reliable way. We show a lab-based prototype that uses the atom-chip itself to retro-reflect the interrogation laser and thus serving as inertial reference inside the vacuum. With this setup it is possible to demonstrate all necessary steps to measure gravity, including the preparation of the source, spanning an interferometer as well as the detection of the output signal, within an area of 1 cm3 right below the atom-chip and to analyze relevant systematic effects. In the framework of the center of excellence geoQ a next generation device is under construction at the Institut für Quantenoptik, that will allow for in-field measurements. This device will feature a state-of-the-art atom-chip source with a high-flux of ultra-cold atoms at a repetition rate of 1-2 Hz. In cooperation with the Müller group at the Institut für Erdmessung the sensor will be characterized in the laboratory first, to be ultimately employed in campaigns to measure the Fennoscandian uplift at the level of 1 μGal. The presented work is part of the center of

  6. Precision laser surveying instrument using atmospheric turbulence compensation by determining the absolute displacement between two laser beam components

    DOEpatents

    Veligdan, James T.

    1993-01-01

    Atmospheric effects on sighting measurements are compensated for by adjusting any sighting measurements using a correction factor that does not depend on atmospheric state conditions such as temperature, pressure, density or turbulence. The correction factor is accurately determined using a precisely measured physical separation between two color components of a light beam (or beams) that has been generated using either a two-color laser or two lasers that project different colored beams. The physical separation is precisely measured by fixing the position of a short beam pulse and measuring the physical separation between the two fixed-in-position components of the beam. This precisely measured physical separation is then used in a relationship that includes the indexes of refraction for each of the two colors of the laser beam in the atmosphere through which the beam is projected, thereby to determine the absolute displacement of one wavelength component of the laser beam from a straight line of sight for that projected component of the beam. This absolute displacement is useful to correct optical measurements, such as those developed in surveying measurements that are made in a test area that includes the same dispersion effects of the atmosphere on the optical measurements. The means and method of the invention are suitable for use with either single-ended systems or a double-ended systems.

  7. Computerized device for critical flicker fusion frequency determination

    NASA Astrophysics Data System (ADS)

    Racene, Diana

    2003-08-01

    The critical fusion flicker frequency of the human visual system is the threshold sensitivity for a sine wave-modulated patch of monochromatic flickering light measured as a function of its temporal frequency and average luminance level. The critical flicker fusion frequency changes in different ocular and non-ocular conditions, for example: high-myopia, AMR, glaucoma, schizophrenia, after alcohol intake, fatigue. A computerized test for critical flicker fusion frequency determination was developed. Visual stimuli are two monochromatic LED light sources that are connected to a microcircuit driven by a computer program. The control of the device is realized through the parallel port of the PC. During the test a patient has to choose which one of two light sources is flickering. The critical cliker fusion frequency is determined by a psychophysical procedure, where the stimulus frequency that showed detection probability 75% is considered as threshold.

  8. Frequency scanning capaciflector for capacitively determining the material properties

    NASA Technical Reports Server (NTRS)

    Campbell, Charles E. (Inventor)

    1996-01-01

    A capaciflector sensor system scanned in frequency is used to detect the permittivity of the material of an object being sensed. A capaciflector sensor element, coupled to current-measuring voltage follower circuitry, is driven by a frequency swept oscillator and generates an output which corresponds to capacity as a function of the input frequency. This swept frequency information is fed into apparatus e.g. a digital computer for comparing the shape of the capacitance vs. frequency curve against characteristic capacitor vs. frequency curves for a variety of different materials which are stored, for example, in a digital memory of the computer or a database. Using a technique of pattern matching, a determination is made as to the identification of the material. Also, when desirable, the distance between the sensor and the object can be determined.

  9. Influence of GPS/GLONASS differential code biases on the determination accuracy of the absolute total electron content in the ionosphere

    NASA Astrophysics Data System (ADS)

    Yasyukevich, Yu. V.; Mylnikova, A. A.; Kunitsyn, V. E.; Padokhin, A. M.

    2015-11-01

    Systematic error arises when the total electron content (TEC) is estimated with the simultaneous use of phase and code GPS/GLONASS measurements. This is related to the different signal propagation times at L1 and L2 frequencies in the radio frequency path of the transmitting and receiving equipment, the so-called differential code biases. A differential code bias of 1 ns results in an error of ~2.9 TECU when TEC is determined. Differential code bias variations on a long time interval, which were obtained at the CODE laboratory, were analyzed. It has been found that the systematic variation in these biases and considerable seasonal variations apparently caused by the environmental state (temperature and humidity), which sometimes reach 20 TECU (in TEC units), are observed for several stations. The algorithm for determining differential code biases at an individual station and the results of correction for absolute slant TEC are also presented. Presented results show algorithm effectiveness for various geographical regions and solar activity.

  10. Determining the importance of model calibration for forecasting absolute/relative changes in streamflow from LULC and climate changes

    USGS Publications Warehouse

    Niraula, Rewati; Meixner, Thomas; Norman, Laura M.

    2015-01-01

    Land use/land cover (LULC) and climate changes are important drivers of change in streamflow. Assessing the impact of LULC and climate changes on streamflow is typically done with a calibrated and validated watershed model. However, there is a debate on the degree of calibration required. The objective of this study was to quantify the variation in estimated relative and absolute changes in streamflow associated with LULC and climate changes with different calibration approaches. The Soil and Water Assessment Tool (SWAT) was applied in an uncalibrated (UC), single outlet calibrated (OC), and spatially-calibrated (SC) mode to compare the relative and absolute changes in streamflow at 14 gaging stations within the Santa Cruz River Watershed in southern Arizona, USA. For this purpose, the effect of 3 LULC, 3 precipitation (P), and 3 temperature (T) scenarios were tested individually. For the validation period, Percent Bias (PBIAS) values were >100% with the UC model for all gages, the values were between 0% and 100% with the OC model and within 20% with the SC model. Changes in streamflow predicted with the UC and OC models were compared with those of the SC model. This approach implicitly assumes that the SC model is “ideal”. Results indicated that the magnitude of both absolute and relative changes in streamflow due to LULC predicted with the UC and OC results were different than those of the SC model. The magnitude of absolute changes predicted with the UC and SC models due to climate change (both P and T) were also significantly different, but were not different for OC and SC models. Results clearly indicated that relative changes due to climate change predicted with the UC and OC were not significantly different than that predicted with the SC models. This result suggests that it is important to calibrate the model spatially to analyze the effect of LULC change but not as important for analyzing the relative change in streamflow due to climate change. This

  11. Determination of the specific heat capacity of a graphite sample using absolute and differential methods

    NASA Astrophysics Data System (ADS)

    Picard, Susanne; Burns, David T.; Roger, Philippe

    2007-10-01

    An experimental assembly has been constructed to measure the specific heat capacity of macroscopic graphite samples at room temperature. The same batch of graphite constitutes the core of a graphite calorimeter, which is currently being realized to measure the absorbed dose due to ionizing radiation. Two different experimental procedures have been applied. In the first method the specific heat capacity of graphite was measured directly, where its value is corrected for the influence of impurities. The second method, to our knowledge not previously applied to macroscopic samples, is based on a series of differential measurements where no correction for added impurities is needed. By its nature, the second method reduces systematic effects. The specific heat capacity of a particular graphite sample is determined to be 706.9 J K-1 kg-1 with a combined relative standard uncertainty of 9 parts in 104 at 295.15 K. The specific heat capacity of cyanoacrylate has also been determined.

  12. Observation and absolute frequency measurements of the 1S0-3P0 optical clock transition in neutral ytterbium.

    PubMed

    Hoyt, C W; Barber, Z W; Oates, C W; Fortier, T M; Diddams, S A; Hollberg, L

    2005-08-19

    We report the direct excitation of the highly forbidden (6s2) 1S0 <--> (6s6p) 3P0 optical transition in two odd isotopes of neutral ytterbium. As the excitation laser frequency is scanned, absorption is detected by monitoring the depletion from an atomic cloud at approximately 70 microK in a magneto-optical trap. The measured frequency in 171Yb (F=1/2) is 518,295,836,591.6 +/- 4.4 kHz. The measured frequency in 173Yb (F=5/2) is 518,294,576,847.6 +/- 4.4 kHz. Measurements are made with a femtosecond-laser frequency comb calibrated by the National Institute of Standards and Technology cesium fountain clock and represent nearly a 10(6)-fold reduction in uncertainty. The natural linewidth of these J=0 to J=0 transitions is calculated to be approximately 10 mHz, making them well suited to support a new generation of optical atomic clocks based on confinement in an optical lattice. PMID:16196856

  13. Absolute optical frequency measurements of the cesium D1 transitions and their effect on alpha, the fine-structured constant

    NASA Astrophysics Data System (ADS)

    Calkins, Keith Gordon

    The fine-structure constant or electromagnetic coupling constant, alpha e, is a dimensionless ratio which unites many physics subfields. Although known precisely via experiments in each subfield, there is disagreement within and between subfields. In particular, precise values obtained via electron ge - 2 experiments which depend heavily on QED calculations have not always been in agreement with those obtained via muon g mu - 2 experiments. Also, solid state measurements (quantum hall effect and AC Josephson effect) often disagree with neutronic hmn measurements. alphae is often said to vary with energy but the question remains as to whether or not its low energy value is stable now or has been stable over the history of the universe. Improved precision helps resolve these issues as they relate to physics, possibly beyond the standard model. The Optical Frequency Measurements group in the Time and Frequency Division at the National Institute of Science and Technology (NIST, Boulder, CO) developed and maintains a femtosecond laser frequency comb which is calibrated with respect to the cesium fountain clock implementation of the second. A single frequency component of the femtosecond laser comb is used together with a solid state diode laser and cesium thermal beam to precisely measure the cesium D1 F ∈ {3,4} transition frequencies. The value of fD1centroid = 335 116 048 748.1(2.4) kHz obtained for the transition centroid is over fifteen times more precise than the most recent previous measurement. A precise value for the cesium D1 hyperfine splitting fHFe = 1 167 723.6(4.7) kHz is reported as well. This value is also over fifteen times more precise than the most recent previous measurement. These new neutral 133Cs 6s 2 S½ → 6p 2 P½ transition (D1) frequencies, when combined with the 2002 CODATA values of the Rydberg, proton/electron mass ratio, cesium atomic mass, and cesium recoil frequency, provide an almost QED-free value of alpha: alphae = 1/137.036 0000

  14. Single Frequency GPS Orbit Determination for Low Earth Orbiters

    NASA Technical Reports Server (NTRS)

    Bertiger, Willy; Wu, Sien-Chong

    1996-01-01

    A number of missions in the future are planning to use GPS for precision orbit determination. Cost considerations and receiver availability make single frequency GPS receivers attractive if the orbit accuracy requirements can be met.

  15. Absolute determination of photoluminescence quantum efficiency using an integrating sphere setup

    SciTech Connect

    Leyre, S.; Coutino-Gonzalez, E.; Hofkens, J.; Joos, J. J.; Poelman, D.; Smet, P. F.; Ryckaert, J.; Meuret, Y.; Durinck, G.; Hanselaer, P.

    2014-12-15

    An integrating sphere-based setup to obtain a quick and reliable determination of the internal quantum efficiency of strongly scattering luminescent materials is presented. In literature, two distinct but similar measurement procedures are frequently mentioned: a “two measurement” and a “three measurement” approach. Both methods are evaluated by applying the rigorous integrating sphere theory. It was found that both measurement procedures are valid. Additionally, the two methods are compared with respect to the uncertainty budget of the obtained values of the quantum efficiency. An inter-laboratory validation using the two distinct procedures was performed. The conclusions from the theoretical study were confirmed by the experimental data.

  16. Absolute np and pp cross section determinations aimed at improving the standard for cross section measurements

    SciTech Connect

    Laptev, Alexander B; Haight, Robert C; Tovesson, Fredrik; Arndt, Richard A; Briscoe, William J; Paris, Mark W; Strakovsky, Igor I; Workman, Ron L

    2010-01-01

    Purpose of present research is a keeping improvement of the standard for cross section measurements of neutron-induced reactions. The cross sections for np and pp scattering below 1000 MeV are determined based on partial-wave analyses (PW As) of nucleon-nucleon scattering data. These cross sections are compared with the most recent ENDF/B-V11.0 and JENDL-4.0 data files, and the Nijmegen PWA. Also a comparison of evaluated data with recent experimental data was made to check a quality of evaluation. Excellent agreement was found between the new experimental data and our PWA predictions.

  17. Absolute np and pp Cross Section Determinations Aimed At Improving The Standard For Cross Section Measurements

    SciTech Connect

    Laptev, A. B.; Haight, R. C.; Tovesson, F.; Arndt, R. A.; Briscoe, W. J.; Paris, M. W.; Strakovsky, I. I.; Workman, R. L.

    2011-06-01

    Purpose of present research is a keeping improvement of the standard for cross section measurements of neutron-induced reactions. The cross sections for np and pp scattering below 1 GeV are determined based on partial-wave analyses (PWAs) of nucleon-nucleon scattering data. These cross sections are compared with the most recent ENDF/B-VII.0 and JENDL-4.0 data files, and the Nijmegen PWA. Also a comparison of evaluated data with recent experimental data was made to check a quality of evaluation. Excellent agreement was found between the new experimental data and our PWA predictions.

  18. Novelty is not enough: laser-evoked potentials are determined by stimulus saliency, not absolute novelty

    PubMed Central

    Ronga, I.; Valentini, E.; Mouraux, A.

    2013-01-01

    Event-related potentials (ERPs) elicited by transient nociceptive stimuli in humans are largely sensitive to bottom-up novelty induced, for example, by changes in stimulus attributes (e.g., modality or spatial location) within a stream of repeated stimuli. Here we aimed 1) to test the contribution of a selective change of the intensity of a repeated stimulus in determining the magnitude of nociceptive ERPs, and 2) to dissect the effect of this change of intensity in terms of “novelty” and “saliency” (an increase of stimulus intensity is more salient than a decrease of stimulus intensity). Nociceptive ERPs were elicited by trains of three consecutive laser stimuli (S1-S2-S3) delivered to the hand dorsum at a constant 1-s interstimulus interval. Three, equally spaced intensities were used: low (L), medium (M), and high (H). While the intensities of S1 and S2 were always identical (L, M, or H), the intensity of S3 was either identical (e.g., HHH) or different (e.g., MMH) from the intensity of S1 and S2. Introducing a selective change in stimulus intensity elicited significantly larger N1 and N2 waves of the S3-ERP but only when the change consisted in an increase in stimulus intensity. This observation indicates that nociceptive ERPs do not simply reflect processes involved in the detection of novelty but, instead, are mainly determined by stimulus saliency. PMID:23136349

  19. Absolute Bragg wavelength and dispersion determination in dispersive incoherent OFDR interrogators

    NASA Astrophysics Data System (ADS)

    Clement, J.; Torregrosa, G.; Hervás, J.; Fernández-Pousa, C. R.

    2016-05-01

    We report on an incoherent OFDR interrogator of FBG arrays based on the concept of dispersive wavelength to time delay mapping. The system is specifically designed to show stability to environmental thermal variations by the incorporation of a composite dispersive delay and weak broadband reflectors for delay and dispersion monitoring. Dispersion is imparted by the combination of a fiber coil and an athermally-packaged chirped fiber Bragg grating for dispersion compensation. Using differential measurements over a single acquisition trace, the values of Bragg wavelengths and dispersion are determined from the delays experienced by the FBGs and by additional reference wavelengths reflected in the broadband reflectors. The results show maximum deviations of 20 pm and 0.2 ps/nm with respect to OSA measurements of Bragg wavelengths and nominal dispersion values, respectively.

  20. [HPLC enantioseparation, absolute configuration determination and anti-HIV-1 activity of (±)-F18 enantiomers].

    PubMed

    Zhang, Lei-lei; Xue, Hai; Li, Li; Lu, Xiao-fan; Chen, Zhi-wei; Lu, Gang

    2015-06-01

    Racemic (±)-F18 (10-chloromethyl-11-demethyl-12-oxo-calanolide A), an analog of nature product (+)-calanolide A, is a new anti-HIV-1 nonnucleoside reverse transcript inhibitor (NNRTI). A successful enantioseparation of (±)-F18 offering (R)-F18 and (S)-F18 was achieved by a chiral stationary phase prepared HPLC. Their absolute configurations were determined by measurement of their electronic circular dichroisms combined with modem quantum-chemical calculations. Further investigation revealed that (R)-F18 and (S)-F18 shared a similar anti-HIV activities, however, (R)-F18 was more potent than (S)-F18 against wild-type virus, K101E mutation and P225H mutation pseudoviruses. PMID:26521445

  1. Improved determination of seafloor absolute magnetization from uneven, near-seafloor magnetic measurements and high-resolution bathymetry

    NASA Astrophysics Data System (ADS)

    Szitkar, F.; Dyment, J.; Choi, Y.; Fouquet, Y.

    2012-12-01

    Vector magnetometers installed on deep-sea submersibles offer a unique opportunity to achieve high resolution magnetic investigations at the scale of hundred to thousand meters. Once corrected for the vehicle induced and remanent magnetization, the measurements mostly reflect variations of the topography and the submersible path - i.e. the distance between the sources and the observation points. The interesting parameter, however, is the seafloor magnetization that can be interpreted in terms of geological processes. Here we present methods to compute absolute magnetization of the seafloor by taking advantage of the uneven track of the submersible. In these methods, synthetic anomalies are computed for a unit magnetization assuming the geometry of the experiment, i.e. the source and the submersible path. The absolute magnetization is determined by a comparison between the observed anomalies and the synthetic ones along sliding windows. The coherency between the two signals gives an estimation of the quality of the determination, and the phase provides information on the magnetic polarity, and therefore the age of volcanic features. Such a method has been developed by Honsho et al. (JGR, 2009) using deep-sea submersible data only, i.e. magnetic anomaly, depth and altitude of the submersible. The synthetic anomalies are computed using 2D forward modeling, i.e. assuming the structures to be infinite in the direction perpendicular to the submersible path. The method has been applied with success to linear profiles crossing elongated structures such as mid-ocean ridges, but may fail for structures departing from the 2D assumption. The adaptation of improving multibeam systems to autonomous underwater vehicles (AUVs) has opened the way to the collection of very high resolution bathymetric data (around 2m between each measurement). This development has triggered a new strategy to explore the seafloor using manned submersibles: an AUV is operated during night time to

  2. Procoagulant and platelet-derived microvesicle absolute counts determined by flow cytometry correlates with a measurement of their functional capacity

    PubMed Central

    Ayers, Lisa; Harrison, Paul; Kohler, Malcolm; Ferry, Berne

    2014-01-01

    Background Flow cytometry is the most commonly used technology to measure microvesicles (MVs). Despite reported limitations of this technique, MV levels obtained using conventional flow cytometry have yielded many clinically relevant findings, such as associations with disease severity and ability to predict clinical outcomes. This study aims to determine if MV enumeration by flow cytometry correlates with a measurement of their functional capacity, as this may explain how flow cytometry generates clinically relevant results. Methods One hundred samples from healthy individuals and patients with obstructive sleep apnoea were analysed by conventional flow cytometry (FACSCalibur) and by three functional MV assays: Zymuphen MP-activity in which data were given as phosphatidylserine equivalent, STA® Phospholipid Procoag Assay expressed as clotting time and Endogenous Thrombin Potential (ETP) reflecting in vitro thrombin generation. Correlations were determined by Spearman correlation. Results Absolute counts of lactadherin+ procoagulant MVs generated by flow cytometry weakly correlated with the results obtained from the Zymuphen MP-activity (r=0.5370, p<0.0001); correlated with ETP (r=0.7444, p<0.0001); negatively correlated with STA® Phospholipid Procoag Assay clotting time (−0.7872, p<0.0001), reflecting a positive correlation between clotting activity and flow cytometry. Levels of Annexin V+ procoagulant and platelet-derived MVs were also associated with functional assays. Absolute counts of MVs derived from other cell types were not correlated with the functional results. Conclusions Quantitative results of procoagulant and platelet-derived MVs from conventional flow cytometry are associated with the functional capability of the MVs, as defined by three functional MV assays. Flow cytometry is a valuable technique for the quantification of MVs from different cellular origins; however, a combination of several analytical techniques may give the most comprehensive

  3. Time domain characterization of oscillating sensors: Application of frequency counting to resonance frequency determination

    NASA Astrophysics Data System (ADS)

    Zeng, Kefeng; Ong, Keat G.; Mungle, Casey; Grimes, Craig A.

    2002-12-01

    A frequency counting technique is described for determining the resonance frequency of a transiently excited sensor; the technique is applicable to any sensor platform where the characteristic resonance frequency is the parameter of interest. The sensor is interrogated by a pulse-like excitation signal, and the resonance frequency of the sensor subsequently determined by counting the number of oscillations per time during sensor ring-down. A repetitive time domain interrogation technique is implemented to overcome the effects of sensor damping, such as that associated with mass loading, which reduces the duration of the sensor ring-down and hence the measurement resolution. The microcontroller based, transient frequency counting technique is detailed with application to the monitoring of magnetoelastic sensors [C. A. Grimes, D. Kouzoudis, and C. Mungle, Rev. Sci. Instrum. 71, 3822 (2000)], with a measurement resolution of 0.001% achieved in approximately 40 ms.

  4. Constraints on the Mid-Continent Deformation Gravity Gradient Determined from Co-located GPS and Absolute Gravity Observations

    NASA Astrophysics Data System (ADS)

    James, T. S.; Mazzotti, S.; Mazzotti, S.; Lambert, A.

    2001-12-01

    The deformation gravity gradient (DGG) is the ratio of the time rate of change of surface gravity to vertical crustal velocity. Different processes generate different theoretical predictions of the DGG. Consequently, observational constraints on the DGG are necessary to link crustal uplift observations to satellite-derived observations of the time rate of change of the Earth's gravitational field, which will be generated by upcoming satellite missions such as GRACE. Larson and van Dam (2000) have compared secular gravity trends from 4 sites in interior North America to crustal uplift rates obtained from global point-positioning analyses of GPS observations, and found they agree, assuming a nominal DGG value appropriate to postglacial rebound of -0.15 μ Gal/mm (Wahr et al., 1995). Here we revisit and extend their analysis in order to determine the observational constraints on the DGG in mid-continent North America. We use recently published gravity rates derived from significantly more absolute gravity observations and a different GPS analysis scheme. Lambert et al. (2001) have published secular gravity rates for 7 sites in mid-continent North America, using all available absolute gravity observations and allowing for instrumental offsets. The sites, chosen to sample postglacial rebound, lie on a transect from Churchill, Manitoba, located on Hudson Bay, to North Liberty, Iowa. Four of these sites (Churchill, Flin Flon, Lac du Bonnet, and North Liberty) also feature a nearby GPS station. The GPS observations were analyzed using double differencing with Bernese 4.2, yielding 5 year time series for vertical position. The daily repeatabilities of 5 to 9 mm compare well to the weekly repeatabilities of 7-8 mm reported by Larson and van Dam (2000). A comparison of the vertical rates derived from these time series to the secular solid-surface gravity trends finds a DGG of -0.14 +/- 0.06 μ Gal/mm. This value is in good agreement with model predictions for postglacial

  5. 40 CFR 93.157 - Frequency of conformity determinations.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Frequency of conformity determinations. 93.157 Section 93.157 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Determining Conformity of General Federal Actions to State or Federal Implementation Plans § 93.157...

  6. Low-frequency rTMS over the Parieto-frontal network during a sensorimotor task: The role of absolute beta power in the sensorimotor integration.

    PubMed

    Gongora, Mariana; Bittencourt, Juliana; Teixeira, Silmar; Basile, Luis F; Pompeu, Fernando; Droguett, Enrique López; Arias-Carrion, Oscar; Budde, Henning; Cagy, Mauricio; Velasques, Bruna; Nardi, Antonio Egídio; Ribeiro, Pedro

    2016-01-12

    Several studies have demonstrated that Repetitive Transcranial Magnetic Stimulation (rTMS) promotes alterations in the Central Nervous System circuits and networks. The focus of the present study is to examine the absolute beta power patterns in the Parieto-frontal network. We hypothesize that rTMS alters the mechanisms of the sensorimotor integration process during a visuomotor task. Twelve young healthy volunteers performed a visuomotor task involving decision making recorded (Catch a ball in a free fall) by Electroencephalography. rTMS was applied on the Superior Parietal Cortex (SPC; Brodmann area [BA] 7) with low-frequency (1 Hz - 15 min - 80% Resting Motor Threshold). For each Frontal and Parietal region, a two-way ANOVA was used to compare the absolute beta power before and after TMS for each condition of the study (Rest 1, Task and Rest 2). The results demonstrated interactions (TMS vs. Condition) for the Frontal electrodes: Fp1, Fp2 and F7 and an effect of TMS (before and after) for F4.The results for the Parietal region showed a main effect of Condition for the P3, PZ and P4 electrodes. Thus, our paradigm was useful to better understand the reorganization and neural plasticity mechanisms in the parieto-frontal network during the sensorimotor integration process. PMID:26608023

  7. Absolute atomic oxygen and nitrogen densities in radio-frequency driven atmospheric pressure cold plasmas: Synchrotron vacuum ultra-violet high-resolution Fourier-transform absorption measurements

    SciTech Connect

    Niemi, K.; O'Connell, D.; Gans, T.; Oliveira, N. de; Joyeux, D.; Nahon, L.; Booth, J. P.

    2013-07-15

    Reactive atomic species play a key role in emerging cold atmospheric pressure plasma applications, in particular, in plasma medicine. Absolute densities of atomic oxygen and atomic nitrogen were measured in a radio-frequency driven non-equilibrium plasma operated at atmospheric pressure using vacuum ultra-violet (VUV) absorption spectroscopy. The experiment was conducted on the DESIRS synchrotron beamline using a unique VUV Fourier-transform spectrometer. Measurements were carried out in plasmas operated in helium with air-like N{sub 2}/O{sub 2} (4:1) admixtures. A maximum in the O-atom concentration of (9.1 {+-} 0.7) Multiplication-Sign 10{sup 20} m{sup -3} was found at admixtures of 0.35 vol. %, while the N-atom concentration exhibits a maximum of (5.7 {+-} 0.4) Multiplication-Sign 10{sup 19} m{sup -3} at 0.1 vol. %.

  8. A Miniaturized Plasma Impedance Probe For Ionospheric Absolute Electron Density and Electron-Neutral Collision Frequency Measurements

    NASA Astrophysics Data System (ADS)

    Patra, S.; Rao, A. J.; Jayaram, M.; Hamoui, M. E.; Spencer, E. A.; Winstead, C.

    2008-12-01

    A fully integrated, low power, miniaturized Plasma Impedance Probe (PIP) is developed for small satellite constellation missions to create a map of electron density in the ionosphere. Two alternative methods for deriving plasma parameters from impedance measurements are discussed. The first method employs a frequency sweep technique, while the second employs a pulse based technique. The pulse based technique is a new method that leads to faster measurements. The two techniques necessitate different specifications for the front end analog circuit design. Unlike previous PIP designs, the integrated PIP performs direct voltage/current sampling at the probe's terminal. The signal processing tasks are performed by an off-chip FPGA to compute the impedance of the probe in the surrounding plasma. The new design includes self- calibration algorithms in order to increase the accuracy and reliability of the probe for small satellite constellation missions. A new feature included in this instrument is that the plasma parameters are derived from impedance measurements directly on the FPGA, significantly reducing the bandwith of telemetered data down to ground.

  9. Absolute concentration determination of phosphorus metabolites in the Langendorff-perfused rabbit heart by phosphorus-31 nuclear magnetic resonance

    SciTech Connect

    Gard, J.K.

    1984-01-01

    The concentrations of mobile high energy phosphorus metabolites and intracellular pH of Langendorff-perfused rabbit heart have been determined under control and reduced flow conditions. Absolute concentration determination was accomplished by Lorentzian lineshape analysis after development of hexachlorocyclotriphosphazene as an external intensity standard. Hearts were demonstrated to be biochemically and physiologically competent during control perfusion periods and compromised during reduced flow conditions by independent hemodynamic and metabolic measurements coincident with the NMR experiment. Reduction in perfusate flow from 20 mL/min to 5.0 mL/min (25% flow) or 2.5 mL/min (12.5% flow) demonstrated a fall in phosphocreatine and adenosine triphosphate concentrations, a rise in cytosolic inorganic phosphate concentrations, and drops in pH. Subsequent recovery upon reflow was observed. The derived values for the free concentration of ADP were very close to the reported values of the Michaelis constant for respiratory stimulation, implicating a regulatory role for this molecule in cellular respiration. Strong evidence that the creating kinase reaction was in equilibrium in the 25% flow study was seen. The NMR observable correlated closely with myocardial performance and biochemical indices of metabolic function, and supported the use of phosphocreatine as an indicator of current metabolic integrity.

  10. Determinations of its Absolute Dimensions and Distance by the Analyses of Light and Radial-Velocity Curves

    NASA Astrophysics Data System (ADS)

    Lee, Jae-Woo; Lee, Chung-Uk; Kim, Chun-Hwey; Kang, Young-Beom; Koo, Jae-Rim

    2004-12-01

    We completed the light curves of the contact binary CK Boo for 13 nights from June to July in 2004 using the 1-m reflector and BVR filters at Mt. Lemmon Optical Astronomy Observatory, and determined four new times of minimum light (three timings for primary eclipse, one for secondary). With contact mode of the 1998-version Wilson-Devinney binary model, we analyzed our BVR light curves and Rucinski & Lu (1999)'s radial-velocity ones. As a result, we found CK boo to be A-type overcontact binary (f=84%) with the low mass ratio (q=0.11) and orbital inclination (i=65°). Absolute dimensions of the system are determined from our new solution; M1=1.42M⊙, M2=0.15M⊙, R1=1.47R⊙, R2=0.59M⊙, and the distance to it is derived as about 129pc. Our distance is well consistent with that (157±33pc) from the Hipparcos trigonometric parallax within the limit of the error yielded by the latter.

  11. Absolute geomagnetic intensity determinations on Formative potsherds (1400-700 BC) from the Oaxaca Valley, Southwestern Mexico

    NASA Astrophysics Data System (ADS)

    Pétronille, Marie; Goguitchaichvili, Avto; Morales, Juan; Carvallo, Claire; Hueda-Tanabe, Yuki

    2012-11-01

    New Thellier-Coe archeointensity determinations have been measured on 15 potsherds from the Oaxaca Valley belonging to three of the four Formative Periods (Pre-Classical) of Mesoamerica, spanning 1400-700 BC. Seven of these are considered to be reliable and indicate a geomagnetic field strength of about 30 μT. This value is some 75% of the present geomagnetic field strength but is in agreement with the absolute intensities predicted from global models for this time and location, and consistent with coeval published determinations. These data thus provide significant evidence for the geomagnetic field strength in an area and for a time that was previously poorly constrained, thus providing an important contribution towards establishing a local master curve for the last 3500 yr. When established, such a curve would be a useful dating tool and also enable establishing for field strength correlations with climatic events and civilization evolutions in a region that is particularly strong in archeological and geological features. Such potential is examined for aridity events, although such observations can only be considered tentative at this stage.

  12. A non-invasive diffuse reflectance calibration-free method for absolute determination of exogenous biochemicals concentration in biological tissues

    NASA Astrophysics Data System (ADS)

    Lappa, Alexander V.; Kulikovskiy, Artem N.; Busarov, Oleg G.

    2014-03-01

    The paper presents a new method for distant non-destructive determination of concentration of light absorbing admixtures in turbid media. In particular, it is intended for non-invasive in vivo control of accumulation in patient tissues of various biochemicals introduced to the patients for chemotherapy, photodynamic therapy or diagnostics. It is require that the admixture absorption spectrum should have a clearly marked peak in the wavelength region where the pure medium one varies regularly. Fluorescence of admixtures is not required. The method uses the local diffuse reflectance spectroscopy with optical fiber probe including one emitting and two reading There are several features in the method: the value to be determined is absolute concentration of admixtures; the method needs no calibration measurements on phantoms; it needs no reference measurements on sample with zero admixture concentration; it uses a two parametric kinetic light propagation model and original algorithms to resolve direct and inverse tasks of radiation transport theory. Experimental testing passed with tissue equivalent phantoms and different admixtures, including a chlorine photosensitizer, showed accuracy under 10% in all cases.

  13. Systems and methods for determining radio frequency interference

    NASA Technical Reports Server (NTRS)

    Johannsen, K. G.; Sabaroff, S.; Henry, V. F. (Inventor)

    1978-01-01

    The presence, frequency and amplitude of radio frequency interference superimposed on communication links originating from a terrestrial region and including a relay in a geostationary spacecraft are determined by pointing a narrow beam antenna on the satellite at the terrestrial region. The level of noise radiated from the region to the antenna is measured at a terrestrial station that is usually remote from the region. Calibrating radio signals having a plurality of predetermined EIRP's (Effective Isotropic Radiated Power) and frequencies in the spectrum are transmitted from the region through the spacecraft narrow beam antenna back to the station. At the station, the levels of the received calibrating signals are separately measured for each of the frequency bands and EIRP's.

  14. Absolute single-ion solvation free energy scale in methanol determined by the lithium cluster-continuum approach.

    PubMed

    Pliego, Josefredo R; Miguel, Elizabeth L M

    2013-05-01

    Absolute solvation free energy of the lithium cation in methanol was calculated by the cluster-continuum quasichemical theory of solvation. Clusters with up to five methanol molecules were investigated using X3LYP, MP2, and MP4 methods with DZVP, 6-311+G(2df,2p), TZVPP+diff, and QZVPP+diff basis sets and including the cluster solvation through the PCM and SMD continuum models. Our calculations have determined a value of -118.1 kcal mol(-1) for the solvation free energy of the lithium, in close agreement with a value of -116.6 kcal mol(-1) consistent with the TATB assumption. Using data of solvation and transfer free energy of a pair of ions, electrode potentials and pKa, we have obtained the solvation free energy of 25 ions in methanol. Our analysis leads to a value of -253.6 kcal mol(-1) for the solvation free energy of the proton, which can be compared with the value of -263.5 kcal mol(-1) obtained by Kelly et al. using the cluster pair approximation. Considering that this difference is due to the methanol surface potential, we have estimated that it corresponds to -0.429 V. PMID:23570440

  15. Absolute number densities of helium metastable atoms determined by atomic absorption spectroscopy in helium plasma-based discharges used as ambient desorption/ionization sources for mass spectrometry

    NASA Astrophysics Data System (ADS)

    Reininger, Charlotte; Woodfield, Kellie; Keelor, Joel D.; Kaylor, Adam; Fernández, Facundo M.; Farnsworth, Paul B.

    2014-10-01

    The absolute number densities of helium atoms in the 2s 3S1 metastable state were determined in four plasma-based ambient desorption/ionization sources by atomic absorption spectroscopy. The plasmas included a high-frequency dielectric barrier discharge (HF-DBD), a low temperature plasma (LTP), and two atmospheric-pressure glow discharges, one with AC excitation and the other with DC excitation. Peak densities in the luminous plumes downstream from the discharge capillaries of the HF-DBD and the LTP were 1.39 × 1012 cm- 3 and 0.011 × 1012 cm- 3, respectively. Neither glow discharge produced a visible afterglow, and no metastable atoms were detected downstream from the capillary exits. However, densities of 0.58 × 1012 cm- 3 and 0.97 × 1012 cm- 3 were measured in the interelectrode regions of the AC and DC glow discharges, respectively. Time-resolved measurements of metastable atom densities revealed significant random variations in the timing of pulsed absorption signals with respect to the voltage waveforms applied to the discharges.

  16. Absolute Zero

    NASA Astrophysics Data System (ADS)

    Donnelly, Russell J.; Sheibley, D.; Belloni, M.; Stamper-Kurn, D.; Vinen, W. F.

    2006-12-01

    Absolute Zero is a two hour PBS special attempting to bring to the general public some of the advances made in 400 years of thermodynamics. It is based on the book “Absolute Zero and the Conquest of Cold” by Tom Shachtman. Absolute Zero will call long-overdue attention to the remarkable strides that have been made in low-temperature physics, a field that has produced 27 Nobel Prizes. It will explore the ongoing interplay between science and technology through historical examples including refrigerators, ice machines, frozen foods, liquid oxygen and nitrogen as well as much colder fluids such as liquid hydrogen and liquid helium. A website has been established to promote the series: www.absolutezerocampaign.org. It contains information on the series, aimed primarily at students at the middle school level. There is a wealth of material here and we hope interested teachers will draw their student’s attention to this website and its substantial contents, which have been carefully vetted for accuracy.

  17. Determination of absolute configuration in chiral solvents with nuclear magnetic resonance. A combined molecular dynamics/quantum chemical study.

    PubMed

    Kessler, Jiří; Dračínský, Martin; Bouř, Petr

    2015-05-28

    Nuclear magnetic resonance (NMR) spectroscopy is omnipresent in chemical analysis. However, chirality of a molecule can only be detected indirectly by NMR, e.g., by monitoring its interaction with another chiral object. In the present study, we investigate the spectroscopic behavior of chiral molecules placed into a chiral solvent. In this case, the solvent-solute interaction is much weaker, but the application range of such NMR analysis is wider than for a specific chemical shift agent. Two alcohols and an amine were used as model systems, and differences in NMR chemical shifts dependent on the solute-solvent chirality combination were experimentally detected. Combined quantum mechanic/molecular mechanic (QM/MM) computations were applied to reveal the underlying solute-solvent interactions. NMR shielding was calculated using the density functional theory (DFT). While the experimental observations could not be reproduced quantitatively, the modeling provided a qualitative agreement and detailed insight into the essence of solvent-solute chiral interactions. The potentials of mean force (PMF) obtained using molecular dynamics (MD) and the weighted histogram analysis method (WHAM) indicate that the chiral interaction brings about differences in conformer ratios, which are to a large extent responsible for the NMR shifts. The MD results also predicted slight changes in the solvent structure, including the radial distribution function (RDF), to depend on the solvent/solute chirality combination. Apart from the conformer distribution, an effective average solvent electrostatic field was tested as another major factor contributing to the chiral NMR effect. The possibility to simulate spectral effects of chiral solvents from the first-principles opens up the way to NMR spectroscopic determination of the absolute configuration for a larger scale of compounds, including those not forming specific complexes. PMID:25411905

  18. Absolute Copy Number and Relative Change in Determinations of Human Immunodeficiency Virus Type 1 RNA in Plasma: Effect of an External Standard on Kit Comparisons

    PubMed Central

    Brambilla, Donald; Leung, Sheila; Lew, Judy; Todd, John; Herman, Steven; Cronin, Mike; Shapiro, David E.; Bremer, James; Hanson, Celine; Hillyer, George V.; McSherry, George D.; Sperling, Rhoda S.; Coombs, Robert W.; Reichelderfer, Patricia S.

    1998-01-01

    Use of a common set of human immunodeficiency virus type 1 (HIV-1) RNA standards eliminated differences among absolute HIV-1 RNA copy number estimates made with three commercially available assays. The relative changes in the viral RNA levels determined by the commercial assays were similar and were unaffected by the use of a common set of standards. PMID:9431977

  19. Simultaneous determination of the absolute configuration of twelve monosaccharide enantiomers from natural products in a single injection by UPLC-UV/MS method

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In natural product chemistry, it is often crucial to determine sugar composition as well as the absolute configuration of each monosaccharide in glycosides. An ultra-performance liquid chromatography method using both photodiode array (PDA) and mass spectrometry detectors (UPLC-UV/MS) was developed....

  20. Absolute and relative emission spectroscopy study of 3 cm wide planar radio frequency atmospheric pressure bio-plasma source

    SciTech Connect

    Deng, Xiaolong; Nikiforov, Anton Yu Leys, Christophe; Ionita, Eusebiu-Rosini; Dinescu, Gheorghe

    2015-08-03

    The dynamics of low power atmospheric pressure radio frequency discharge generated in Ar gas in long gap of 3 cm is investigated. This plasma source is characterized and analyzed for possible large scale biomedical applications where low gas temperature and potential-less effluent are required. The discharge forms a homogenous glow-like afterglow in ambient air at input power of 30 W with low gas temperature of 330 K, which is desirable in biomedical applications. With absolute calibrated spectroscopy of the discharge, electron density of 0.4 × 10{sup 18} m{sup −3} and electron temperature of 1.5 eV are obtained from continuum Bremsstrahlung radiation of the source. Time and spatial resolved emission spectroscopy is used to analyze discharge generation mechanism and active species formation. It is found that discharge dynamics strongly correlates with the discharge current waveform. Strong Ar(2p) excited states emission is observed nearby the electrodes surface on a distance up to 200 μm in the plasma sheath region at 10 ns after the current peak, whereas OH(A) emission is uniform along of the interelectrode gap.

  1. Extension of the absolute flux density scale to 22.285 GHz. [radio astronomy

    NASA Technical Reports Server (NTRS)

    Janssen, M. A.; Golden, L. M.; Welch, W. J.

    1974-01-01

    Extending the absolute flux density scale at microwave wavelengths, the absolute flux densities at 22.285 GHz of several standard sources were determined using the absolute calibrations of the 6.1 meter antenna of the Hat Creek Observatory. Interpolation formulas for each nonthermal standard source have been derived by combining these data with those determined at lower frequencies. The suitability of employing the standard sources for calibrating other antennas is discussed.

  2. Connectivity, Not Frequency, Determines the Fate of a Morpheme

    PubMed Central

    Keller, Daniela Barbara; Schultz, Jörg

    2013-01-01

    Morphemes are the smallest meaningful parts of words and therefore represent a natural unit to study the evolution of words. To analyze the influence of language change on morphemes, we performed a large scale analysis of German and English vocabulary covering the last 200 years. Using a network approach from bioinformatics, we examined the historical dynamics of morphemes, the fixation of new morphemes and the emergence of words containing existing morphemes. We found that these processes are driven mainly by the number of different direct neighbors of a morpheme in words (connectivity, an equivalent to family size or type frequency) and not its frequency of usage (equivalent to token frequency). This contrasts words, whose survival is determined by their frequency of usage. We therefore identified features of morphemes which are not dictated by the statistical properties of words. As morphemes are also relevant for the mental representation of words, this result might enable establishing a link between an individual’s perception of language and historical language change. PMID:23922865

  3. Absolute Summ

    NASA Astrophysics Data System (ADS)

    Phillips, Alfred, Jr.

    Summ means the entirety of the multiverse. It seems clear, from the inflation theories of A. Guth and others, that the creation of many universes is plausible. We argue that Absolute cosmological ideas, not unlike those of I. Newton, may be consistent with dynamic multiverse creations. As suggested in W. Heisenberg's uncertainty principle, and with the Anthropic Principle defended by S. Hawking, et al., human consciousness, buttressed by findings of neuroscience, may have to be considered in our models. Predictability, as A. Einstein realized with Invariants and General Relativity, may be required for new ideas to be part of physics. We present here a two postulate model geared to an Absolute Summ. The seedbed of this work is part of Akhnaton's philosophy (see S. Freud, Moses and Monotheism). Most important, however, is that the structure of human consciousness, manifest in Kenya's Rift Valley 200,000 years ago as Homo sapiens, who were the culmination of the six million year co-creation process of Hominins and Nature in Africa, allows us to do the physics that we do. .

  4. Resolution and Determination of the Absolute Configuration of a Twisted Bis-Lactam Analogue of Tröger's Base: A Comparative Spectroscopic and Computational Study.

    PubMed

    Rúnarsson, Ögmundur Vidar; Benkhäuser, Christian; Christensen, Niels Johan; Ruiz, Josep Artacho; Ascic, Erhad; Harmata, Michael; Snieckus, Victor; Rissanen, Kari; Fristrup, Peter; Lützen, Arne; Wärnmark, Kenneth

    2015-08-21

    The first reported twisted bis-lactam, a racemic Tröger's base (TB) analogue (2), was resolved into its enantiomers on a chiral stationary phase HPLC column. The absolute configuration of (+)-2 was determined to be (R,R)-2 by comparing experimental and calculated vibrational circular dichroism (VCD) and electronic circular dichroism (ECD) spectra. The absolute configuration of (-)-2 was determined by comparing experimental and calculated electronic circular dichroism (ECD) spectra. The corresponding theoretical spectra were calculated using the lowest energy conformation of (R,R)-2 and (S,S)-2 at the B3LYP/6-31G(d,p) level of theory. The absolute configuration of (+)-2 was also determined to (R,R)-2 by anomalous X-ray diffraction (AXRD) in a chiral space group P212121 using Cu-irradiation resulting in a very low Flack parameter of -0.06(3), despite the heaviest element being an oxygen atom, thus unambiguously confirming the results from the spectroscopic studies. We conclude that, for the Tröger's base (TB) analogue (2), we may rank the reliability of the individual methods for AC determination as AXRD ≫ VCD > ECD, while the synergy of all three methods provides very strong confidence in the assigned ACs of (+)-(R,R)-2 and (-)-(S,S)-2. PMID:26244379

  5. Apparatus for use in determining surface conductivity at microwave frequencies

    NASA Technical Reports Server (NTRS)

    Hearn, Chase P. (Inventor)

    1997-01-01

    An apparatus is provided for use in determining surface conductivity of a flat or shaped conductive material at microwave frequencies. A plate has an electrically conductive surface with first and second holes passing through the plate. An electrically conductive material under test (MUT) is maintained in a spaced apart relationship with the electrically conductive surface of the plate by one or more non-conductive spacers. A first coupling loop is electrically shielded within the first hole while a second coupling loop is electrically shielded within the second hole. A dielectric resonator element is positioned between the first and second coupling loops, while also being positioned closer to the MUT than the electrically conductive surface of the plate. Microwave energy at an operating frequency f is supplied from a signal source to the first coupling loop while microwave energy received at the second coupling loop is measured. The apparatus is capable of measuring the Q-factor of the dielectric resonator situated in the cavity existing between the electrically conductive surface of the plate and the MUT. Surface conductivity of the electrically conductive surface can be determined via interpolation using: 1) the measured Q-factor with the electrically conductive surface in place, and 2) the measured Q-factor when the MUT is replaced with reference standards having known surface conductivities.

  6. Apparatus for Use in Determining Surface Conductivity at Microwave Frequencies

    NASA Technical Reports Server (NTRS)

    Hearn, Chase P. (Inventor)

    1995-01-01

    An apparatus is provided for use in determining surface conductivity of a flat or shaped conductive material at microwave frequencies. A plate has an electrically conductive surface with first and second holes passing through the plate. An electrically conductive material under test (MUT) is maintained in a spaced apart relationship with the electrically conductive surface of the plate by one or more nonconductive spacers. A first coupling loop is electrically shielded within the first hole while a second coupling loop is electrically shielded within the second hole. A dielectric resonator element is positioned between the first and second coupling loops, while also being positioned closer to the MUT than the electrically conductive surface of the plate. Microwave energy at an operating frequency f is supplied from a signal source to the first coupling loop while microwave energy received at the second coupling loop is measured. The apparatus is capable of measuring the Q-factor of the dielectric resonator situated in the 'cavity' existing between the electrically conductive surface of the plate and the MUT. Surface conductivity of the electrically conductive surface can be determined via interpolation using: 1 ) the measured Q-factor with the electrically conductive surface in place, and 2) the measured Q-factor when the MUT is replaced with reference standards having known surface conductivities.

  7. Apparatus for use in determining surface conductivity at microwave frequencies

    NASA Astrophysics Data System (ADS)

    Hearn, Chase P.

    1995-05-01

    An apparatus is provided for use in determining surface conductivity of a flat or shaped conductive material at microwave frequencies. A plate has an electrically conductive surface with first and second holes passing through the plate. An electrically conductive material under test (MUT) is maintained in a spaced apart relationship with the electrically conductive surface of the plate by one or more nonconductive spacers. A first coupling loop is electrically shielded within the first hole while a second coupling loop is electrically shielded within the second hole. A dielectric resonator element is positioned between the first and second coupling loops, while also being positioned closer to the MUT than the electrically conductive surface of the plate. Microwave energy at an operating frequency f is supplied from a signal source to the first coupling loop while microwave energy received at the second coupling loop is measured. The apparatus is capable of measuring the Q-factor of the dielectric resonator situated in the 'cavity' existing between the electrically conductive surface of the plate and the MUT. Surface conductivity of the electrically conductive surface can be determined via interpolation using: 1 ) the measured Q-factor with the electrically conductive surface in place, and 2) the measured Q-factor when the MUT is replaced with reference standards having known surface conductivities.

  8. Absolute frequency spectroscopy of CO2 lines at around 2.09 μm by combined use of an Er:fiber comb and a Ho:YLF amplifier.

    PubMed

    Gatti, D; Coluccelli, N; Gambetta, A; Di Lieto, A; Tonelli, M; Galzerano, G; Laporta, P; Marangoni, M

    2011-10-01

    The low-frequency tail of an octave-spanning supercontinuum (SC) generated by an Er:fiber comb is enhanced by a multipass Ho:YLF amplifier and used in a sum-frequency-generation scheme to obtain absolute referencing of a single-mode Tm-Ho:YAG laser tunable around 2.09 μm. By tuning the comb repetition frequency, the probing laser is scanned across the absorption lines of a CO(2) gas sample and highly accurate absorption profiles are measured. This approach can be readily scaled to any wavelength above ~2 μm. PMID:21964142

  9. A Nonempirical Approach for Direct Determination of the Absolute Configuration of 1,2-Diols and Amino Alcohols Using Mg(II)bisporphyrin.

    PubMed

    Ikbal, Sk Asif; Dhamija, Avinash; Brahma, Sanfaori; Rath, Sankar Prasad

    2016-07-01

    We report here a simple, facile, and direct nonempirical protocol for determining the absolute stereochemistry of a variety of chiral 1,2-diols and amino alcohols at room temperature with no chemical derivatization using Mg(II)bisporphyrin as a host. Addition of excess substrates resulted in the formation of a 1:2 host-guest complex in which two substrates bind in an unusual endo-endo fashion because of interligand H-bonding within the bisporphyrin cavity leading to the formation of a unidirectional screw in the bisporphyrin moiety that allowed us an accurate absolute stereochemical determination of the chiral substrate via exciton-coupled circular dichroism (ECCD). The sign of the CD couplet has also been found to be inverted when the stereogenic center is moved by one C atom simply from the bound to an unbound functionality and thus able to discriminate between them successfully. Strong complexation of the alcoholic oxygen with Mg(II)bisporphyrin rigidifies the host-guest complex, which eventually enhances its ability to stereochemically differentiate the asymmetric center. The ECCD sign of a large number of substrates has followed consistent and predictable trends; thus, the system is widely applicable. Moreover, computational calculations clearly support the experimental observations along with the absolute stereochemistry of the chiral substrate. PMID:27231970

  10. Determination of the absolute configuration of pentacoordinate chiral phosphorus compounds in solution by using vibrational circular dichroism spectroscopy and density functional theory.

    PubMed

    Yang, Guochun; Xu, Yunjie; Hou, Jianbo; Zhang, Hui; Zhao, Yufen

    2010-02-22

    Vibrational circular dichroism (VCD) spectroscopic measurements and density functional theory (DFT) calculations have been used to obtain the absolute structural information about four sets of diastereomers of pentacoordinate spirophosphoranes derived separately from l- (or d-) valine and l- (or d-) leucine for the first time. Each compound contains three stereogenic centers: one at the phosphorus center and two at the amino acid ligands. Extensive conformational searches for the compounds have been carried out and their vibrational absorption (VA) and VCD spectra have been simulated at the B3LYP/6-311++G** level. Although both VA and VCD spectra are highly sensitive to the structural variation of the apical axis, that is, the O-P-O or N-P-O arrangement, the rotamers generated by the aliphatic amino side chains show little effect on both. The dominant experimental VCD features in the 1100-1500 cm(-1) region were found to be controlled by the chirality at the phosphorus center, whereas those at the C=O stretching region are determined by the chirality of the amino acid ligands. The good agreement between the experimental VA and VCD spectra in CDCl(3) solution and the simulated ones allows us to assign the absolute configurations of these pentacoordinate phosphorus compounds with high confidence. This study shows that the VCD spectroscopy complemented with DFT calculations is a powerful and reliable method for determining the absolute configurations and dominating conformers of synthetic phosphorus coordination complexes in solution. PMID:20077536

  11. The lowest spatial frequency channel determines brightness perception.

    PubMed

    Perna, A; Morrone, M C

    2007-05-01

    This study investigates the role played by individual spatial scales in determining the apparent brightness of greyscale patterns. We measured the perceived difference in brightness across an edge in the presence of notch filtering and high-pass filtering for two stimulus configurations, one that elicits the perception of transparency and one that appears opaque. For both stimulus configurations, the apparent brightness of the surfaces delimited by the border decreased monotonically with progressive (ideal) high-pass filtering, with a critical cut-off at 1 c/deg. Using two octave ideal notch filtering, the maximum detrimental effect on apparent brightness was observed at about 1c/deg. Critical frequencies for apparent brightness did not vary with contrast, viewing distance, or surface size, suggesting that apparent brightness is determined by the channel tuned at 1 c/deg. Modelling the data with the local energy model [Morrone, M. C., & Burr, D. C. (1988). Feature detection in human vision: a phase dependent energy model. Proceedings of the Royal Society (London), B235, 221-245] at 1c/deg confirmed the suggestion that this channel mediates apparent brightness for both opaque and transparent borders, with no need for pooling or integration across spatial channels. PMID:17395237

  12. Determination of subjective similarity for pairs of masses and pairs of clustered microcalcifications on mammograms: Comparison of similarity ranking scores and absolute similarity ratings

    SciTech Connect

    Muramatsu, Chisako; Li Qiang; Schmidt, Robert A.; Shiraishi, Junji; Suzuki, Kenji; Newstead, Gillian M.; Doi, Kunio

    2007-07-15

    The presentation of images that are similar to that of an unknown lesion seen on a mammogram may be helpful for radiologists to correctly diagnose that lesion. For similar images to be useful, they must be quite similar from the radiologists' point of view. We have been trying to quantify the radiologists' impression of similarity for pairs of lesions and to establish a ''gold standard'' for development and evaluation of a computerized scheme for selecting such similar images. However, it is considered difficult to reliably and accurately determine similarity ratings, because they are subjective. In this study, we compared the subjective similarities obtained by two different methods, an absolute rating method and a 2-alternative forced-choice (2AFC) method, to demonstrate that reliable similarity ratings can be determined by the responses of a group of radiologists. The absolute similarity ratings were previously obtained for pairs of masses and pairs of microcalcifications from five and nine radiologists, respectively. In this study, similarity ranking scores for eight pairs of masses and eight pairs of microcalcifications were determined by use of the 2AFC method. In the first session, the eight pairs of masses and eight pairs of microcalcifications were grouped and compared separately for determining the similarity ranking scores. In the second session, another similarity ranking score was determined by use of mixed pairs, i.e., by comparison of the similarity of a mass pair with that of a calcification pair. Four pairs of masses and four pairs of microcalcifications were grouped together to create two sets of eight pairs. The average absolute similarity ratings and the average similarity ranking scores showed very good correlations in the first study (Pearson's correlation coefficients: 0.94 and 0.98 for masses and microcalcifications, respectively). Moreover, in the second study, the correlations between the absolute ratings and the ranking scores were also

  13. Absolute CF{sub 2} density and gas temperature measurements by absorption spectroscopy in dual-frequency capacitively coupled CF{sub 4}/Ar plasmas

    SciTech Connect

    Liu, Wen-Yao; Xu, Yong Peng, Fei; Gong, Fa-Ping; Li, Xiao-Song; Zhu, Ai-Min; Liu, Yong-Xin; Wang, You-Nian

    2014-10-15

    Broadband ultraviolet absorption spectroscopy has been used to determine the CF{sub 2} radical density in dual-frequency capacitively coupled CF{sub 4}/Ar plasmas, using the CF{sub 2} A{sup ~1}B{sub 1}←X{sup ~1}A{sub 1} system of absorption spectrum. The rotational temperature of ground state CF{sub 2} and excited state CF was also estimated by using A{sup ~1}B{sub 1}←X{sup ~1}A{sub 1} system and B{sup 2}Δ−X{sup 2}Π system, respectively. The translational gas temperature was deduced from the Doppler width of the Ar{sup *}({sup 3}P{sub 2}) and Ar{sup *}({sup 3}P{sub 0}) metastable atoms absorption line by using the tunable diode laser absorption spectroscopy. The rotational temperatures of the excited state CF are about 100 K higher than those of ground state CF{sub 2}, and about 200 K higher than the translational gas temperatures. The dependences of the radical CF{sub 2} density, electron density, electron temperature, rotational temperature, and gas temperature on the high frequency power and pressure have been analyzed. Furthermore, the production and loss mechanisms of CF{sub 2} radical and the gas heating mechanisms have also been discussed.

  14. Digital slip frequency generator and method for determining the desired slip frequency

    DOEpatents

    Klein, Frederick F.

    1989-01-01

    The output frequency of an electric power generator is kept constant with variable rotor speed by automatic adjustment of the excitation slip frequency. The invention features a digital slip frequency generator which provides sine and cosine waveforms from a look-up table, which are combined with real and reactive power output of the power generator.

  15. Determination of relative and absolute photoionization cross-sections in multiply-charged Ba^n+ Ions

    NASA Astrophysics Data System (ADS)

    Bizau, J.-M.; Cubaynes, D.; Esteva, J. M.; Wuilleumier, F. J.; Marmoret, R.; Petrault, L.; Remond, C.; Couillaud, C.; Compant La Fontaine, A.; Blancard, C.; Hitz, D.; Ludwig, P.; Deshmukh, P. C.; Zhou, H.-L.; Manson, S. T.

    2001-05-01

    Following our first photoionization measurements for the multiply-charged Xe^n+ [1] and Ba^2+ [2] ions, we introduced several modifications in the experimental set-up to allow us to measure absolute cross sections for multiply-charged ions. Photoionization studies of barium ions up to Ba^6+ were performed using synchrotron radiation emitted by an undulator of the Super ACO storage ring in Orsay and an ECR ion source. Collapse of the 4f (ɛ f) orbitals has been observed to occur faster than for Xe^n+: the relative intensity of transitions to continuum states is negligible already for Ba^3+ ions, discrete transitions to 4d^95s^25p^mnf states then dominating the measured spectra. The experimental results are in good agreement with the results of MCDF calculations for the discrete transitions and, in Ba^2+, with RRPA calculations for transitions to continuum states. 1. J.-M. Bizau et al., Phys. Rev. Lett. 84, 435 (2000). 2. J.-M. Bizau et al., Bull. Am. Phys. Soc. 45, 61 (2000).

  16. Severity and Frequency of Proximal Tubule Injury Determines Renal Prognosis.

    PubMed

    Takaori, Koji; Nakamura, Jin; Yamamoto, Shinya; Nakata, Hirosuke; Sato, Yuki; Takase, Masayuki; Nameta, Masaaki; Yamamoto, Tadashi; Economides, Aris N; Kohno, Kenji; Haga, Hironori; Sharma, Kumar; Yanagita, Motoko

    2016-08-01

    AKI increases the risk of developing CKD, but the mechanisms linking AKI to CKD remain unclear. Because proximal tubule injury is the mainstay of AKI, we postulated that proximal tubule injury triggers features of CKD. We generated a novel mouse model to induce proximal tubule-specific adjustable injury by inducing the expression of diphtheria toxin (DT) receptor with variable prevalence in proximal tubules. Administration of high-dose DT in mice expressing the DT receptor consistently caused severe proximal tubule-specific injury associated with interstitial fibrosis and reduction of erythropoietin production. Mild proximal tubule injury from a single injection of low-dose DT triggered reversible fibrosis, whereas repeated mild injuries caused sustained interstitial fibrosis, inflammation, glomerulosclerosis, and atubular glomeruli. DT-induced proximal tubule-specific injury also triggered distal tubule injury. Furthermore, injured tubular cells cocultured with fibroblasts stimulated induction of extracellular matrix and inflammatory genes. These results support the existence of proximal-distal tubule crosstalk and crosstalk between tubular cells and fibroblasts. Overall, our data provide evidence that proximal tubule injury triggers several features of CKD and that the severity and frequency of proximal tubule injury determines the progression to CKD. PMID:26701981

  17. Determination of Delta m(d) and absolute calibration of flavor taggers for the Delta m(s) analysis, in fully reconstructed decays at the CDF experiment

    SciTech Connect

    Gomez, Jonatan Piedra

    2005-07-01

    The new trigger processor, the Silicon Vertex Tracking (SVT), has dramatically improved the B physics capabilities of the upgraded CDF II Detector; for the first time in a hadron collider, the SVT has enabled the access to non-lepton-triggered B meson decays. Within the new available range of decay modes, the B{sub s}{sup 0} {yields} D{sub s}{sup -}{pi}{sup +} signature is of paramount importance in the measurement of the {Delta}m{sub s} mixing frequency. The analysis reported here is a step towards the measurement of this frequency; two where our goals: carrying out the absolute calibration of the opposite side flavor taggers, used in the {Delta}m{sub s} measurement; and measuring the B{sub d}{sup 0} mixing frequency in a B {yields} D{pi} sample, establishing the feasibility of the mixing measurement in this sample whose decay-length is strongly biased by the selective SVT trigger. We analyze a total integrated luminosity of 355 pb{sup -1} collected with the CDF II Detector. By triggering on muons, using the conventional di-muon trigger; or displaced tracks, using the SVT trigger, we gather a sample rich in bottom and charm mesons.

  18. Towards determination of absolute molar mass of cellulose polymer by size exclusion chromatography with mulitple angle laser light scattering detection.

    PubMed

    Pawcenis, Dominika; Thomas, Jacob L; Łojewski, Tomasz; Milczarek, Jakub M; Łojewska, Joanna

    2015-08-28

    The study focuses on determination of a set of crucial parameters for molar mass calculation of cellulose from the results of size exclusion chromatography coupled with multiple angle laser light scattering (MALLS) and differential refractive index (DRI) detectors. In the present work, cellulose has been derivatised to obtain cellulose tricarbanilate (CTC) soluble in tetrahydrofuran (THF). The parameters of Rayleigh scattering in the MALLS detector: refractive index increment (dn/dc) and second virial coefficient (A2) of CTC in THF were determined for laser wavelength 658nm. In order to avoid errors resulting from cellulose derivatisation by-products present in the CTC solution, the so called "on-line" method of measuring dn/dc and A2 was applied. Based on the A2 determination, its influence on cellulose molar mass calculations and cellulose molecular dimensions were critically assessed. The latter includes evaluation of artificially aged cellulose towards conceivable branching by conformation plot analysis. PMID:26210115

  19. Absolute determination of power density in the VVER-1000 mock-up on the LR-0 research reactor.

    PubMed

    Košt'ál, Michal; Švadlenková, Marie; Milčák, Ján

    2013-08-01

    The work presents a detailed comparison of calculated and experimentally determined net peak areas of selected fission products gamma lines. The fission products were induced during a 2.5 h irradiation on the power level of 9.5 W in selected fuel pins of the VVER-1000 Mock-Up. The calculations were done with deterministic and stochastic (Monte Carlo) methods. The effects of different nuclear data libraries used for calculations are discussed as well. The Net Peak Area (NPA) may be used for the determination of fission density across the mock-up. This fission density is practically identical to power density. PMID:23665766

  20. A whole rock absolute paleointensity determination of dacites from the Duffer Formation (ca. 3.467 Ga) of the Pilbara Craton, Australia: An impossible task?

    NASA Astrophysics Data System (ADS)

    Herrero-Bervera, Emilio; Krasa, David; Van Kranendonk, Martin J.

    2016-09-01

    We have conducted a whole-rock type magnetic and absolute paleointensity determination of the red dacite of the Duffer Formation from the Pilbara Craton, Australia. The age of the dated rock unit is 3467 ± 5 Ma (95% confidence). Vector analyses results of the step-wise alternating field demagnetization (NRM up to 100 mT) and thermal demagnetization (from NRM up to 650 °C) yield three components of magnetization. Curie point determinations indicate three characteristic temperatures, one at 150-200 °C, a second one at ∼450 °C and a third one at ∼580 °C. Magnetic grain-size experiments were performed on small specimens with a variable field translation balance (VFTB). The coercivity of remanence (Hcr) suggests that the NRM is carried by low-coercivity grains that are associated with a magnetite fraction as is shown by the high-temperature component with blocking temperatures above 450 °C and up to at least 580 °C. The ratios of the hysteresis parameters plotted as a modified Day diagram show that most grain sizes are scattered within the Single Domain (SD) and the Superparamagnetic and Single Domain SP-SD domain ranges. In addition to the rock magnetic experiments we have performed absolute paleointensity experiments on the samples using the modified Thellier-Coe double heating method to determine the paleointensities. Partial-TRM (p-TRM) checks were performed systematically to document magnetomineralogical changes during heating. The temperature was incremented by steps of 50 °C between room temperature and 590 °C. The paleointensity determinations were obtained from the slope of Arai diagrams. Our paleointensity results indicate that the paleofield obtained was ∼6.4 ± 0.68 (N = 11) micro-Teslas with a Virtual Dipole Moment (VDM) of 1.51 ± 0.81 × 1022 Am2, from a medium-to high-temperature component ranging from 300 to 590 °C that has been interpreted to be the oldest magnetization yet recorded in paleomagnetic studies of the Duffer Formation. The

  1. Combining Steady-State and Dynamic Methods for Determining Absolute Signs of Hyperfine Interactions: Pulsed ENDOR Saturation and Recovery (PESTRE)

    PubMed Central

    Doan, Peter E.

    2010-01-01

    The underlying causes of asymmetric intensities in Davies pulsed ENDOR spectra that are associated with the signs of the hyperfine interaction are reinvestigated. The intensity variations in these asymmetric ENDOR patterns are best described as shifts in an apparent baseline intensity that occurs dynamically following on-resonance ENDOR transitions. We have developed an extremely straightforward multi-sequence protocol that is capable of giving the sign of the hyperfine interaction by probing a single ENDOR transition, without reference to its partner transition. This technique, Pulsed ENDOR Saturatation and Recovery (PESTRE) monitors dynamic shifts in the ‘baseline’ following measurements at a single RF frequency (single ENDOR peak), rather than observing anomalous ENDOR intensity differences between the two branches of an ENDOR response. These baseline shifts, referred to as dynamic reference levels (DRLs), can be directly tied to the electron spin manifold from which that ENDOR transition arises. The application of this protocol is demonstrated on 57Fe ENDOR of a 2Fe-2S ferredoxin. We use the 14N ENDOR transitions of the S = 3/2 [Fe(II)NO]2+ center of the non-heme iron enzyme, anthranilate dioxygenase (AntDO) to examine the details of the relaxation model using PESTRE. PMID:21075026

  2. Measurement of the B-->pi l nu branching fraction and determination of absolute value of V(ub) with tagged B mesons.

    PubMed

    Aubert, B; Barate, R; Bona, M; Boutigny, D; Couderc, F; Karyotakis, Y; Lees, J P; Poireau, V; Tisserand, V; Zghiche, A; Grauges, E; Palano, A; Chen, J C; Qi, N D; Rong, G; Wang, P; Zhu, Y S; Eigen, G; Ofte, I; Stugu, B; Abrams, G S; Battaglia, M; Brown, D N; Button-Shafer, J; Cahn, R N; Charles, E; Gill, M S; Groysman, Y; Jacobsen, R G; Kadyk, J A; Kerth, L T; Kolomensky, Yu G; Kukartsev, G; Lynch, G; Mir, L M; Orimoto, T J; Pripstein, M; Roe, N A; Ronan, M T; Wenzel, W A; del Amo Sanchez, P; Barrett, M; Ford, K E; Harrison, T J; Hart, A J; Hawkes, C M; Morgan, S E; Watson, A T; Held, T; Koch, H; Lewandowski, B; Pelizaeus, M; Peters, K; Schroeder, T; Steinke, M; Boyd, J T; Burke, J P; Cottingham, W N; Walker, D; Cuhadar-Donszelmann, T; Fulsom, B G; Hearty, C; Knecht, N S; Mattison, T S; McKenna, J A; Khan, A; Kyberd, P; Saleem, M; Sherwood, D J; Teodorescu, L; Blinov, V E; Bukin, A D; Druzhinin, V P; Golubev, V B; Onuchin, A P; Serednyakov, S I; Skovpen, Yu I; Solodov, E P; Todyshev, K Yu; Best, D S; Bondioli, M; Bruinsma, M; Chao, M; Curry, S; Eschrich, I; Kirkby, D; Lankford, A J; Lund, P; Mandelkern, M; Mommsen, R K; Roethel, W; Stoker, D P; Abachi, S; Buchanan, C; Foulkes, S D; Gary, J W; Long, O; Shen, B C; Wang, K; Zhang, L; Hadavand, H K; Hill, E J; Paar, H P; Rahatlou, S; Sharma, V; Berryhill, J W; Campagnari, C; Cunha, A; Dahmes, B; Hong, T M; Kovalskyi, D; Richman, J D; Beck, T W; Eisner, A M; Flacco, C J; Heusch, C A; Kroseberg, J; Lockman, W S; Nesom, G; Schalk, T; Schumm, B A; Seiden, A; Spradlin, P; Williams, D C; Wilson, M G; Albert, J; Chen, E; Dvoretskii, A; Fang, F; Hitlin, D G; Narsky, I; Piatenko, T; Porter, F C; Ryd, A; Samuel, A; Mancinelli, G; Meadows, B T; Mishra, K; Sokoloff, M D; Blanc, F; Bloom, P C; Chen, S; Ford, W T; Hirschauer, J F; Kreisel, A; Nagel, M; Nauenberg, U; Olivas, A; Ruddick, W O; Smith, J G; Ulmer, K A; Wagner, S R; Zhang, J; Chen, A; Eckhart, E A; Soffer, A; Toki, W H; Wilson, R J; Winklmeier, F; Zeng, Q; Altenburg, D D; Feltresi, E; Hauke, A; Jasper, H; Petzold, A; Spaan, B; Brandt, T; Klose, V; Lacker, H M; Mader, W F; Nogowski, R; Schubert, J; Schubert, K R; Schwierz, R; Sundermann, J E; Volk, A; Bernard, D; Bonneaud, G R; Grenier, P; Latour, E; Thiebaux, Ch; Verderi, M; Clark, P J; Gradl, W; Muheim, F; Playfer, S; Robertson, A I; Xie, Y; Andreotti, M; Bettoni, D; Bozzi, C; Calabrese, R; Cibinetto, G; Luppi, E; Negrini, M; Petrella, A; Piemontese, L; Prencipe, E; Anulli, F; Baldini-Ferroli, R; Calcaterra, A; de Sangro, R; Finocchiaro, G; Pacetti, S; Patteri, P; Peruzzi, I M; Piccolo, M; Rama, M; Zallo, A; Buzzo, A; Capra, R; Contri, R; Lo Vetere, M; Macri, M M; Monge, M R; Passaggio, S; Patrignani, C; Robutti, E; Santroni, A; Tosi, S; Brandenburg, G; Chaisanguanthum, K S; Morii, M; Wu, J; Dubitzky, R S; Marks, J; Schenk, S; Uwer, U; Bard, D J; Bhimji, W; Bowerman, D A; Dauncey, P D; Egede, U; Flack, R L; Nash, J A; Nikolich, M B; Panduro Vazquez, W; Behera, P K; Chai, X; Charles, M J; Mallik, U; Meyer, N T; Ziegler, V; Cochran, J; Crawley, H B; Dong, L; Eyges, V; Meyer, W T; Prell, S; Rosenberg, E I; Rubin, A E; Gritsan, A V; Denig, A G; Fritsch, M; Schott, G; Arnaud, N; Davier, M; Grosdidier, G; Höcker, A; Le Diberder, F; Lepeltier, V; Lutz, A M; Oyanguren, A; Pruvot, S; Rodier, S; Roudeau, P; Schune, M H; Stocchi, A; Wang, W F; Wormser, G; Cheng, C H; Lange, D J; Wright, D M; Chavez, C A; Forster, I J; Fry, J R; Gabathuler, E; Gamet, R; George, K A; Hutchcroft, D E; Payne, D J; Schofield, K C; Touramanis, C; Bevan, A J; Di Lodovico, F; Menges, W; Sacco, R; Cowan, G; Flaecher, H U; Hopkins, D A; Jackson, P S; McMahon, T R; Ricciardi, S; Salvatore, F; Wren, A C; Brown, D N; Davis, C L; Allison, J; Barlow, N R; Barlow, R J; Chia, Y M; Edgar, C L; Lafferty, G D; Naisbit, M T; Williams, J C; Yi, J I; Chen, C; Hulsbergen, W D; Jawahery, A; Lae, C K; Roberts, D A; Simi, G; Blaylock, G; Dallapiccola, C; Hertzbach, S S; Li, X; Moore, T B; Saremi, S; Staengle, H; Cowan, R; Sciolla, G; Sekula, S J; Spitznagel, M; Taylor, F; Yamamoto, R K; Kim, H; McLachlin, S E; Patel, P M; Robertson, S H; Lazzaro, A; Lombardo, V; Palombo, F; Bauer, J M; Cremaldi, L; Eschenburg, V; Godang, R; Kroeger, R; Sanders, D A; Summers, D J; Zhao, H W; Brunet, S; Côté, D; Simard, M; Taras, P; Viaud, F B; Nicholson, H; Cavallo, N; De Nardo, G; Fabozzi, F; Gatto, C; Lista, L; Monorchio, D; Paolucci, P; Piccolo, D; Sciacca, C; Baak, M; Raven, G; Snoek, H L; Jessop, C P; Losecco, J M; Allmendinger, T; Benelli, G; Gan, K K; Honscheid, K; Hufnagel, D; Jackson, P D; Kagan, H; Kass, R; Rahimi, A M; Ter-Antonyan, R; Wong, Q K; Blount, N L; Brau, J; Frey, R; Igonkina, O; Lu, M; Rahmat, R; Sinev, N B; Strom, D; Strube, J; Torrence, E; Gaz, A; Margoni, M; Morandin, M; Pompili, A; Posocco, M; Rotondo, M; Simonetto, F; Stroili, R; Voci, C; Benayoun, M; Chauveau, J; Briand, H; David, P; Del Buono, L; de la Vaissière, Ch; Hamon, O; Hartfiel, B L; John, M J J; Leruste, Ph; Malclès, J; Ocariz, J; Roos, L; Therin, G; Gladney, L; Panetta, J; Biasini, M; Covarelli, R; Angelini, C; Batignani, G; Bettarini, S; Bucci, F; Calderini, G; Carpinelli, M; Cenci, R; Forti, F; Giorgi, M A; Lusiani, A; Marchiori, G; Mazur, M A; Morganti, M; Neri, N; Paoloni, E; Rizzo, G; Walsh, J J; Haire, M; Judd, D; Wagoner, D E; Biesiada, J; Danielson, N; Elmer, P; Lau, Y P; Lu, C; Olsen, J; Smith, A J S; Telnov, A V; Bellini, F; Cavoto, G; D'Orazio, A; del Re, D; Di Marco, E; Faccini, R; Ferrarotto, F; Ferroni, F; Gaspero, M; Li Gioi, L; Mazzoni, M A; Morganti, S; Piredda, G; Polci, F; Safai Tehrani, F; Voena, C; Ebert, M; Schröder, H; Waldi, R; Adye, T; De Groot, N; Franek, B; Olaiya, E O; Wilson, F F; Aleksan, R; Emery, S; Gaidot, A; Ganzhur, S F; Hamel de Monchenault, G; Kozanecki, W; Legendre, M; Vasseur, G; Yèche, Ch; Zito, M; Chen, X R; Liu, H; Park, W; Purohit, M V; Wilson, J R; Allen, M T; Aston, D; Bartoldus, R; Bechtle, P; Berger, N; Claus, R; Coleman, J P; Convery, M R; Cristinziani, M; Dingfelder, J C; Dorfan, J; Dubois-Felsmann, G P; Dujmic, D; Dunwoodie, W; Field, R C; Glanzman, T; Gowdy, S J; Graham, M T; Halyo, V; Hast, C; Hryn'ova, T; Innes, W R; Kelsey, M H; Kim, P; Leith, D W G S; Li, S; Luitz, S; Luth, V; Lynch, H L; MacFarlane, D B; Marsiske, H; Messner, R; Muller, D R; O'Grady, C P; Ozcan, V E; Perazzo, A; Perl, M; Pulliam, T; Ratcliff, B N; Roodman, A; Salnikov, A A; Schindler, R H; Schwiening, J; Snyder, A; Stelzer, J; Su, D; Sullivan, M K; Suzuki, K; Swain, S K; Thompson, J M; Va'vra, J; van Bakel, N; Weaver, M; Weinstein, A J R; Wisniewski, W J; Wittgen, M; Wright, D H; Yarritu, A K; Yi, K; Young, C C; Burchat, P R; Edwards, A J; Majewski, S A; Petersen, B A; Roat, C; Wilden, L; Ahmed, S; Alam, M S; Bula, R; Ernst, J A; Jain, V; Pan, B; Saeed, M A; Wappler, F R; Zain, S B; Bugg, W; Krishnamurthy, M; Spanier, S M; Eckmann, R; Ritchie, J L; Satpathy, A; Schilling, C J; Schwitters, R F; Izen, J M; Lou, X C; Ye, S; Bianchi, F; Gallo, F; Gamba, D; Bomben, M; Bosisio, L; Cartaro, C; Cossutti, F; Della Ricca, G; Dittongo, S; Lanceri, L; Vitale, L; Azzolini, V; Martinez-Vidal, F; Banerjee, Sw; Bhuyan, B; Brown, C M; Fortin, D; Hamano, K; Kowalewski, R; Nugent, I M; Roney, J M; Sobie, R J; Back, J J; Harrison, P F; Latham, T E; Mohanty, G B; Pappagallo, M; Band, H R; Chen, X; Cheng, B; Dasu, S; Datta, M; Flood, K T; Hollar, J J; Kutter, P E; Mellado, B; Mihalyi, A; Pan, Y; Pierini, M; Prepost, R; Wu, S L; Yu, Z; Neal, H

    2006-11-24

    We report a measurement of the B-->pi l nu branching fraction based on 211 fb(-1) of data collected with the BABAR detector. We use samples of B0 and B+ mesons tagged by a second B meson reconstructed in a semileptonic or hadronic decay and combine the results assuming isospin symmetry to obtain B(B(0)-->pi- l+ nu) = (1.33+/-0.17stat+/-0.11syst) x 10(-4). We determine the magnitude of the Cabibbo-Kobayashi-Maskawa matrix element absolute value V(ub) by combining the partial branching fractions measured in ranges of the momentum transfer squared and theoretical calculations of the form factor. Using a recent lattice QCD calculation, we find absolute value V(ub) = (4.5+/-0.5stat+/-0.3syst(+0.7) -0.5FF x 10(-3), where the last error is due to the normalization of the form factor. PMID:17155736

  3. Absolute paleointensity determinations by using of conventional double-heating and multispecimen approaches on a Pliocene lava flow sequence from the Lesser Caucasus

    NASA Astrophysics Data System (ADS)

    Goguitchaichvili, Avto; Caccavari, Ana; Calvo-Rathert, Manuel; Morales, Juan; Solano, Miguel Cervantes; Vashakidze, Goga; Huaiyu, He; Vegas, Néstor

    2016-08-01

    We report 28 successful Thellier type absolute geomagnetic paleointensity determinations from a Pleistocene lava sequence composed of 39 successive flows in the Djavakheti Highland (Lesser Caucasus, Georgia). Additionally, multispecimen technique provided the estimation of geomagnetic field strength for 12 independent cooling units. Paleointensity studies were performed using both Thellier type double heating and multispecimen techniques. Samples selection was mainly based on uni-vectorial remanent magnetization, thermal stability and domain size of the samples. Flow-mean Thellier paleointensity values range from 16.3 ± 5.2 to 71.0 ± 0.3 μT, while intensities obtained using multispecimen approach vary from17.2 ± 2.3 to 69.3 ± 7.9 μT. One of the flows is located near a possible discontinuity in the sequence and yields a rather low Thellier absolute intensity (16.3 ± 5.2) suggesting a transitional regime and the onset of the Matuyama-Olduvai polarity transition, which does not appear on the directional record. Multispecimen paleointensities from the same flow, however, yield higher, close to present day values which makes untenable the hypothesis of occurrence of transitional field. Thus the whole sequence was emplaced in a short time between the Olduvai chron and 1.73 ± 0.03 Ma, as suggested by available radiometric and paleomagnetic data (Caccavari et al., 2014).

  4. Determination of critical assembly absolute power using post-irradiation activation measurement of week-lived fission products.

    PubMed

    Košťál, Michal; Švadlenková, Marie; Milčák, Ján; Rypar, Vojtěch; Koleška, Michal

    2014-07-01

    The work presents a detailed comparison of calculated and experimentally determined net peak areas of longer-living fission products after 100 h irradiation on a reactor with power of ~630 W and several days cooling. Specifically the nuclides studied are (140)Ba, (103)Ru, (131)I, (141)Ce, (95)Zr. The good agreement between the calculated and measured net peak areas, which is better than in determination using short lived (92)Sr, is reported. The experiment was conducted on the VVER-1000 mock-up installed on the LR-0 reactor. The Monte Carlo approach has been used for calculations. The influence of different data libraries on results of calculation is discussed as well. PMID:24566373

  5. Using a Novel Absolute Ontogenetic Age Determination Technique to Calculate the Timing of Tooth Eruption in the Saber-Toothed Cat, Smilodon fatalis

    PubMed Central

    Wysocki, M. Aleksander; Feranec, Robert S.; Tseng, Zhijie Jack; Bjornsson, Christopher S.

    2015-01-01

    Despite the superb fossil record of the saber-toothed cat, Smilodon fatalis, ontogenetic age determination for this and other ancient species remains a challenge. The present study utilizes a new technique, a combination of data from stable oxygen isotope analyses and micro-computed tomography, to establish the eruption rate for the permanent upper canines in Smilodon fatalis. The results imply an eruption rate of 6.0 millimeters per month, which is similar to a previously published average enamel growth rate of the S. fatalis upper canines (5.8 millimeters per month). Utilizing the upper canine growth rate, the upper canine eruption rate, and a previously published tooth replacement sequence, this study calculates absolute ontogenetic age ranges of tooth development and eruption in S. fatalis. The timing of tooth eruption is compared between S. fatalis and several extant conical-toothed felids, such as the African lion (Panthera leo). Results suggest that the permanent dentition of S. fatalis, except for the upper canines, was fully erupted by 14 to 22 months, and that the upper canines finished erupting at about 34 to 41 months. Based on these developmental age calculations, S. fatalis individuals less than 4 to 7 months of age were not typically preserved at Rancho La Brea. On the whole, S. fatalis appears to have had delayed dental development compared to dental development in similar-sized extant felids. This technique for absolute ontogenetic age determination can be replicated in other ancient species, including non-saber-toothed taxa, as long as the timing of growth initiation and growth rate can be determined for a specific feature, such as a tooth, and that growth period overlaps with the development of the other features under investigation. PMID:26132165

  6. Determining the frequency dependence of elastic properties of fractured rocks

    NASA Astrophysics Data System (ADS)

    Ahrens, Benedikt; Renner, Jörg

    2016-04-01

    In the brittle crust, rocks often contain joints or faults on various length scales that have a profound effect on fluid flow and heat transport, as well as on the elastic properties of rocks. Improving the understanding of the effect of fractures and the role of stress state and heterogeneity along the fractures on elastic properties of rocks is potentially important for the characterization of deep geothermal reservoirs. Seismic surveys, typically covering a frequency range of about 1 to 1000 Hz, are a valuable tool to investigate fractured rocks but the extraction of fracture properties remains difficult. The elementary frequency-dependent interaction between fractured rock matrix and viscous pore fluids and the resulting effects on wave propagation require well-founded dispersion analyses of heterogeneous rocks. In this laboratory study, we investigate the stress dependence of the effective elastic properties of fractured reservoir rocks over a broad frequency range. To assess the effect of faults on the effective elastic properties, we performed cyclic axial loading tests on intact and fractured samples of Solnhofen limestone and Padang granodiorite. The samples contained an idealized fault, which was created by stacking two sample discs on top of each other that experienced various surface treatments to vary their roughness. The dynamic loading tests were conducted with frequencies up to 10 Hz and amplitudes reaching 10% of the statically applied stress. Simultaneously, P- and S-wave measurements were performed in the ultrasonic frequency range (above 100 kHz) with a total of 16 sensors, whose positioning above and below the samples guarantees a wide range of transmission and reflection angles. Preliminary results of static and dynamic elastic properties of intact Padang granodiorite show a pronounced increase in Young's moduli and Poisson's ratio with increasing axial stress. Stress relaxation is accompanied by a decrease of the modulus and the Poisson

  7. Teaching Absolute Value Meaningfully

    ERIC Educational Resources Information Center

    Wade, Angela

    2012-01-01

    What is the meaning of absolute value? And why do teachers teach students how to solve absolute value equations? Absolute value is a concept introduced in first-year algebra and then reinforced in later courses. Various authors have suggested instructional methods for teaching absolute value to high school students (Wei 2005; Stallings-Roberts…

  8. Determining radio frequency heating uniformity in mixed beans for disinfestations

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Our laboratory collaborates with USDA-ARS in Parlier, CA in developing thermal treatments based on radio frequency (RF) energy for insect control in legumes to meet postharvest phytosanitary regulations for international market. Our current study focuses on lentils and chickpeas that are two importa...

  9. Determination of the absolute configuration of chaetoviridins and other bioactive azaphilones from the endophytic fungus Chaetomium globosum.

    PubMed

    Youn, Ui Joung; Sripisut, Tawanun; Park, Eun-Jung; Kondratyuk, Tamara P; Fatima, Nighat; Simmons, Charles J; Wall, Marisa M; Sun, Dianqing; Pezzuto, John M; Chang, Leng Chee

    2015-11-01

    Chemical investigation of an endophytic fungus Chaetomium globosum isolated from leaves of Wikstroemia uva-ursi led to the isolation of two new azaphilones, chaetoviridins J and K (1 and 3), along with five known derivatives (2 and 4-7). The structures of azaphilones were determined by NMR, X-ray diffraction, Mosher's method, and CD analysis. The isolated compounds were evaluated for their cancer chemopreventive-potential based on their abilities to inhibit tumor necrosis factor alpha (TNF-α)-induced nuclear factor-kappa B (NF-κB). Compounds 4, 5, 7, and synthetic 8 and 9 inhibit nitric oxide (NO) production with IC50 values in the range of 0.3-5.8 μM. Compounds 4, 5, and 9 also displayed (TNF-α)-induced NF-κB activity with IC50 values in the range of 0.9-5.1 μM. PMID:26343828

  10. The determination of absolute intensity of 234mPa's 1001 keV gamma emission using Monte Carlo simulation.

    PubMed

    Begy, Robert-Csaba; Cosma, Constantin; Timar, Alida; Fulea, Dan

    2009-05-01

    The 1001 keV gamma line of (234m)Pa became important in gamma spectrometric measurements of samples with (238)U content with the advent of development of HpGe detectors of great dimension and high efficiency. In this study the emission probability of the 1001 keV (Y(gamma)) peak of (234m)Pa, was determined by gamma-ray spectrometric measurements performed on glass with Uranium content using Monte Carlo simulation code for efficiency calibration. This method of calculation was not applied for the values quoted in literature so far, at least to our knowledge. The measurements gave an average of 0.836 +/- 0.022%, a value that is in very good agreement to some of the recent results previously presented. PMID:19384056

  11. MODELING MULTI-WAVELENGTH STELLAR ASTROMETRY. III. DETERMINATION OF THE ABSOLUTE MASSES OF EXOPLANETS AND THEIR HOST STARS

    SciTech Connect

    Coughlin, J. L.; Lopez-Morales, Mercedes

    2012-05-10

    Astrometric measurements of stellar systems are becoming significantly more precise and common, with many ground- and space-based instruments and missions approaching 1 {mu}as precision. We examine the multi-wavelength astrometric orbits of exoplanetary systems via both analytical formulae and numerical modeling. Exoplanets have a combination of reflected and thermally emitted light that causes the photocenter of the system to shift increasingly farther away from the host star with increasing wavelength. We find that, if observed at long enough wavelengths, the planet can dominate the astrometric motion of the system, and thus it is possible to directly measure the orbits of both the planet and star, and thus directly determine the physical masses of the star and planet, using multi-wavelength astrometry. In general, this technique works best for, though is certainly not limited to, systems that have large, high-mass stars and large, low-mass planets, which is a unique parameter space not covered by other exoplanet characterization techniques. Exoplanets that happen to transit their host star present unique cases where the physical radii of the planet and star can be directly determined via astrometry alone. Planetary albedos and day-night contrast ratios may also be probed via this technique due to the unique signature they impart on the observed astrometric orbits. We develop a tool to examine the prospects for near-term detection of this effect, and give examples of some exoplanets that appear to be good targets for detection in the K to N infrared observing bands, if the required precision can be achieved.

  12. Synthesis of (3S,3′S)- and meso-Stereoisomers of Alloxanthin and Determination of Absolute Configuration of Alloxanthin Isolated from Aquatic Animals

    PubMed Central

    Yamano, Yumiko; Maoka, Takashi; Wada, Akimori

    2014-01-01

    In order to determine the absolute configuration of naturally occurring alloxanthin, a HPLC analytical method for three stereoisomers 1a–c was established by using a chiral column. Two authentic samples, (3S,3′S)- and meso-stereoisomers 1b and 1c, were chemically synthesized according to the method previously developed for (3R,3′R)-alloxanthin (1a). Application of this method to various alloxanthin specimens of aquatic animals demonstrated that those isolated from shellfishes, tunicates, and crucian carp are identical with (3R,3′R)-stereoisomer 1a, and unexpectedly those from lake shrimp, catfish, biwa goby, and biwa trout are mixtures of three stereoisomers of 1a–c. PMID:24862182

  13. Conformational Slippage Determines Rotational Frequency in Five-Component Nanorotors.

    PubMed

    Samanta, Soumen K; Rana, Anup; Schmittel, Michael

    2016-02-01

    Several five-component nanorotors ROT-3 that rotate at different rates were prepared by adding phenanthrolines of distinct lateral size as brake blocks to the four-component nanorotor ROT-2. The brake blocks interfere with the 180° rotor causing the rotational frequency to drop from 97 kHz to 5 kHz. The effect of the rotating brake blocks on the rotational frequency in ROT-3 is accurately predicted by a nanomechanical model called "conformational slippage". For quantification, the interaction of the brake blocks with the trajectory of the main rotator is gauged based on the number of interfering vs. non-interfering conformations as computed by PM6. PMID:26836349

  14. Meteoroid mass determination using head echoes detected at multiple frequencies

    NASA Astrophysics Data System (ADS)

    Close, Sigrid; Oppenheim, Meers; Hunt, Stephen; McKeen, Fred; Coster, Anthea

    2002-11-01

    Meteor data collected at the Kwajalein Missile Range (KMR) during the peak of the 1998 Leonid storm comprise the only simultaneous data collection of meteor head echoes and trails using seven frequencies (VHF, UHF, L-, S-, C-, Ka- and W-band). The primary sensor was the ALTAIR radar operating at 160 MHz with 30-m range resolution and 422 MHz with 7.5-m range resolution, which has both interferometric and polarization capabilities. This paper presents an alaysis of these high-resolution data in support of the following ideas: First, head echo scattering appears to arise from an ionized region with a density sufficiently high that its plasma frequency exceeds the radar frequency (overdense reflection). Second, the Radar-cross-section (RCS) values, which decrease with decreasing wavelength, peak near 105 km altitude at the point where the meteoroid gives up the most kinetic energy during its descent. Third, these RCS measurements were used to compute electron line densities, which provide estimates of a meteoroid's mass. By combining these data and simple ablation models, we can constrain meteoroid mass as it loses material during its passage through the atmosphere.

  15. Absolute Antenna Calibration at the US National Geodetic Survey

    NASA Astrophysics Data System (ADS)

    Mader, G. L.; Bilich, A. L.

    2012-12-01

    format. The NGS absolute system is located in Corbin, Virginia, and uses field measurements and actual GNSS satellite signals to quantitatively determine the carrier phase advance/delay introduced by the antenna element. NGS is interested in providing calibrations for a wide variety of dual-frequency, geodetic-grade antennas, from types in use at IGS and CORS reference stations to rover antennas not normally seen in those networks. In this presentation, we describe the NGS absolute calibration facility, and discuss the observation models and strategy used to generate NGS absolute calibrations. We also demonstrate that NGS absolute phase center variation (PCV) patterns are consistent with published values determined by other absolute antenna calibration facilities.

  16. An attempt to determine the absolute geomagnetic field intensity in Southwestern Iceland during the Gauss-Matuyama reversal

    NASA Astrophysics Data System (ADS)

    Goguitchaichvili, Avto; Prévot, Michel; Thompson, John; Roberts, Neil

    1999-08-01

    We have measured the variation in the intensity of the geomagnetic field during the Gauss-Matuyama (N4-R3) polarity reversal by application of the Thelliers' method to specimens of lava flows from Hvalfjördur district in Western Iceland (Reynivallahals Mts.). Eleven lava flows all show very similar directions corresponding to an equatorial VGP (Plat=2.9°N, Plong=81.9°E, A95=4.2, K=119). Twenty-nine specimens from nine of the flows were pre-selected for palaeointensity determination on the basis that specimens from the same drill cores showed a single component of magnetisation upon thermal or AF demagnetisation, and possessed low magnetic viscosity and reversible susceptibility curves upon heating at 600-650°C. Observation that the directional data obtained in the course of the palaeointensity experiments occasionally showed substantial non-linearity indicates that a significant chemical remanent magnetization (CRM) can be acquired in the direction of the laboratory field during heating at T. For each double heating step we calculated the ratio of CRM( T) to the magnitude of the natural remanent magnetization (NRM( T)) in the direction of characteristic remanence (obtained independently from another specimen from the same core). When this ratio exceeded 15%, the paleointensity data was rejected. In addition, specimens for which the quality factor was less than 5 were rejected. Twelve reliable palaeointensity values were obtained from specimens representing five lava flows. The results confirm that the palaeointensity was substantially reduced during the N4-R3 reversal. The range of mean palaeointensity values obtained for the five flows is 8.8 to 20.5 and the overall mean is 14.8±4.6 μT. This corresponds to an equivalent VDM of 3.81±1.19 (10 22 A m 2). A comparison of all Thellier palaeointensity data from the R3 magnetozone in the Rayinivallahals Mts. area reveals a progressive although irregular increase in the palaeointensity between the Gauss

  17. Mechanisms of Atrial Fibrillation: Rotors, Ionic Determinants, and Excitation Frequency.

    PubMed

    Berenfeld, Omer; Jalife, José

    2016-04-01

    Atrial fibrillation (AF) is the most common cardiac arrhythmia; however, therapy is suboptimal. We review recent data on dynamics of wave propagation during AF and its mechanistic link to the substrate. Data show that the dominant frequency (DF) increase during transition to persistent AF may be explained by rotor acceleration. We discuss how translation of experimentally derived understanding of the rotors may find its way into the clinic, focusing on studies analyzing spatial distribution of DF in the atria of patients with paroxysmal versus persistent AF, and how that knowledge might contribute to improve the outcome of AF ablation procedures. PMID:26968663

  18. Mechanisms of atrial fibrillation: rotors, ionic determinants, and excitation frequency.

    PubMed

    Berenfeld, Omer; Jalife, José

    2014-11-01

    Atrial fibrillation (AF) is the most common cardiac arrhythmia; however, therapy is suboptimal. We review recent data on dynamics of wave propagation during AF and its mechanistic link to the substrate. Data show that the dominant frequency (DF) increase during transition to persistent AF may be explained by rotor acceleration. We discuss how translation of experimentally derived understanding of the rotors may find its way into the clinic, focusing on studies analyzing spatial distribution of DF in the atria of patients with paroxysmal versus persistent AF, and how that knowledge might contribute to improve the outcome of AF ablation procedures. PMID:25443232

  19. Lysogen stability is determined by the frequency of activity bursts from the fate-determining gene

    PubMed Central

    Zong, Chenghang; So, Lok-hang; Sepúlveda, Leonardo A; Skinner, Samuel O; Golding, Ido

    2010-01-01

    The ability of living cells to maintain an inheritable memory of their gene-expression state is key to cellular differentiation. Bacterial lysogeny serves as a simple paradigm for long-term cellular memory. In this study, we address the following question: in the absence of external perturbation, how long will a cell stay in the lysogenic state before spontaneously switching away from that state? We show by direct measurement that lysogen stability exhibits a simple exponential dependence on the frequency of activity bursts from the fate-determining gene, cI. We quantify these gene-activity bursts using single-molecule-resolution mRNA measurements in individual cells, analyzed using a stochastic mathematical model of the gene-network kinetics. The quantitative relation between stability and gene activity is independent of the fine details of gene regulation, suggesting that a quantitative prediction of cell-state stability may also be possible in more complex systems. PMID:21119634

  20. Lysogen stability is determined by the frequency of activity bursts from the fate-determining gene.

    PubMed

    Zong, Chenghang; So, Lok-hang; Sepúlveda, Leonardo A; Skinner, Samuel O; Golding, Ido

    2010-11-30

    The ability of living cells to maintain an inheritable memory of their gene-expression state is key to cellular differentiation. Bacterial lysogeny serves as a simple paradigm for long-term cellular memory. In this study, we address the following question: in the absence of external perturbation, how long will a cell stay in the lysogenic state before spontaneously switching away from that state? We show by direct measurement that lysogen stability exhibits a simple exponential dependence on the frequency of activity bursts from the fate-determining gene, cI. We quantify these gene-activity bursts using single-molecule-resolution mRNA measurements in individual cells, analyzed using a stochastic mathematical model of the gene-network kinetics. The quantitative relation between stability and gene activity is independent of the fine details of gene regulation, suggesting that a quantitative prediction of cell-state stability may also be possible in more complex systems. PMID:21119634

  1. Observation and Absolute Frequency Measurements of the {sup 1}S{sub 0}-{sup 3}P{sub 0} Optical Clock Transition in Neutral Ytterbium

    SciTech Connect

    Hoyt, C.W.; Barber, Z.W.; Oates, C.W.; Fortier, T.M.; Diddams, S.A.; Hollberg, L.

    2005-08-19

    We report the direct excitation of the highly forbidden (6s{sup 2}){sup 1}S{sub 0}{r_reversible}(6s6p){sup 3}P{sub 0} optical transition in two odd isotopes of neutral ytterbium. As the excitation laser frequency is scanned, absorption is detected by monitoring the depletion from an atomic cloud at {approx}70 {mu}K in a magneto-optical trap. The measured frequency in {sup 171}Yb (F=1/2) is 518 295 836 591.6{+-}4.4 kHz. The measured frequency in {sup 173}Yb (F=5/2) is 518 294 576 847.6{+-}4.4 kHz. Measurements are made with a femtosecond-laser frequency comb calibrated by the National Institute of Standards and Technology cesium fountain clock and represent nearly a 10{sup 6}-fold reduction in uncertainty. The natural linewidth of these J=0 to J=0 transitions is calculated to be {approx}10 mHz, making them well suited to support a new generation of optical atomic clocks based on confinement in an optical lattice.

  2. Determination of transit time distribution and Rabi frequency by applying regularized inverse on Ramsey spectra

    SciTech Connect

    Park, Young-Ho; Lee, Soo Heyong; Park, Sang Eon; Lee, Ho Seong; Kwon, Taeg Yong

    2007-04-23

    The authors report on a method to determine the Rabi frequency and transit time distribution of atoms that are essential for proper operation of atomic beam frequency standards. Their method, which employs alternative regularized inverse on two Ramsey spectra measured at different microwave powers, can be used for the frequency standards with short Ramsey cavity as well as long ones. The authors demonstrate that uncertainty in Rabi frequency obtained from their method is 0.02%.

  3. Spectroscopic determination of kinetic parameters for frequency sweeping Alfven eigenmodes

    SciTech Connect

    Lesur, M.; Idomura, Y.; Shinohara, K.; Garbet, X.

    2010-12-15

    A method for analyzing fundamental kinetic plasma parameters, such as linear drive and external damping rate, based on experimental observations of chirping Alfven eigenmodes, is presented. The method, which relies on new semiempirical laws for nonlinear chirping characteristics, consists of fitting procedures between the so-called Berk-Breizman model and the experiment in a quasiperiodic chirping regime. This approach is applied to the toroidicity induced Alfven eigenmode (TAE) on JT-60 Upgrade (JT-60U) [N. Oyama et al., Nucl. Fusion 49, 104007 (2009)], which yields an estimation of the kinetic parameters and suggests the existence of TAEs far from marginal stability. Two collision models are considered, and it is shown that dynamical friction and velocity-space diffusion are essential to reproduce nonlinear features observed in experiments. The results are validated by recovering measured growth and decay of perturbation amplitude and by estimating collision frequencies from experimental equilibrium data.

  4. Mechanisms of Atrial Fibrillation: Rotors, Ionic Determinants and Excitation Frequency

    PubMed Central

    Berenfeld, Omer; Jalife, José

    2014-01-01

    Summary Atrial fibrillation (AF) is the most common sustained cardiac arrhythmia in humans. However its mechanisms are poorly understood and AF therapy is often sub-optimal. This article reviews recent experimental, numerical and clinical data on dynamics of wave propagation during AF and its mechanistic link to ionic and structural properties of the atria. At the outset, we review numerical and optical mapping data suggesting that the sustained activity of periodic drivers (rotors) with exceedingly high dominant frequencies (DF) of excitation underlies the spatial dispersion and irregularity of activation rates that characterize AF. We show how optical mapping of the fibrillating atria in isolated normal sheep hearts has revealed that the rotors tend to localize in the left atrium (LA). We then discuss exciting new data in the sheep model of tachypacing induced AF demonstrating that the DF of paroxysmal AF episodes increases progressively over days or weeks during the transition to persistent AF (PeAF) and that the rate of the DF increase predicts the onset of PeAF. The data show that the DF increase during the transition may be explained by rotor acceleration secondary to upregulation of IK1 and downregulation of ICaL. The article concludes with a discussion on how translation of experimentally derived knowledge on the behavior and frequency of rotors may find its way into the clinic. We focus on studies in which the analysis of the spatial patterns of DF distribution in the atria of patients with paroxysmal vs persistent has increased our understanding of human AF and how that knowledge might contribute to improve the outcome of AF ablation procedures. PMID:25443232

  5. Eosinophil count - absolute

    MedlinePlus

    Eosinophils; Absolute eosinophil count ... the white blood cell count to give the absolute eosinophil count. ... than 500 cells per microliter (cells/mcL). Normal value ranges may vary slightly among different laboratories. Talk ...

  6. Determinations of its Absolute Dimensions and Distance by the Analyses of Light and Radial-Velocity Curves of the Contact Binary -I. V417 Aquilae

    NASA Astrophysics Data System (ADS)

    Lee, Jae-Woo; Kim, Chun-Hwey; Lee, Chung-Uk; Oh, Kyu-Dong

    2004-06-01

    New photometric and spectroscopic solutions of W-type overcontact binary V417 Aql were obtained by solving the UBV light curves of Samec et al. (1997) and radial-velocity ones of Lu & Rucinski (1999) with the 2003 version of the Wilson-Devinney binary code. In the light curve synthesis the light of a third-body, which Qian (2003) proposed, was considered and obtained about 2.7%, 2.2%, and 0.4% for U, B, and V bandpasses, respectively. The model with third-light is better fitted to eclipse parts than that with no third-light. Absolute dimensions of V417 Aql are determined from our solution as M1=0.53 M⊙, M2=1.45 M⊙, R1=0.84 R⊙ and R2=1.31 M⊙, and the distance to it is deduced as about 216pc. Our distance is well consistent with that (204pc) derived from Rucinski & Duerbeck's (1997) relation, MV=MV(log P, B-V), but is more distant than that (131±40pc) determined by the Hipparcos trigonometric parallax. The difference may result from the relatively large error of Hipparcos parallax for V417 Aql.

  7. MODELING MULTI-WAVELENGTH STELLAR ASTROMETRY. II. DETERMINING ABSOLUTE INCLINATIONS, GRAVITY-DARKENING COEFFICIENTS, AND SPOT PARAMETERS OF SINGLE STARS WITH SIM LITE

    SciTech Connect

    Coughlin, Jeffrey L.; Harrison, Thomas E.; Gelino, Dawn M.

    2010-11-10

    We present a novel technique to determine the absolute inclination of single stars using multi-wavelength submilliarcsecond astrometry. The technique exploits the effect of gravity darkening, which causes a wavelength-dependent astrometric displacement parallel to a star's projected rotation axis. We find that this effect is clearly detectable using SIM Lite for various giant stars and rapid rotators, and present detailed models for multiple systems using the REFLUX code. We also explore the multi-wavelength astrometric reflex motion induced by spots on single stars. We find that it should be possible to determine spot size, relative temperature, and some positional information for both giant and nearby main-sequence stars utilizing multi-wavelength SIM Lite data. These data will be extremely useful in stellar and exoplanet astrophysics, as well as supporting the primary SIM Lite mission through proper multi-wavelength calibration of the giant star astrometric reference frame, and reduction of noise introduced by starspots when searching for extrasolar planets.

  8. Film thickness frequency distribution of different vehicles determines sunscreen efficacy

    NASA Astrophysics Data System (ADS)

    Sohn, Myriam; Hêche, Adeline; Herzog, Bernd; Imanidis, Georgios

    2014-11-01

    Sun protection factor (SPF) frequently differs between sunscreens containing the same composition of ultraviolet (UV) filters that primarily define sunscreen efficacy. We tested the hypothesis that the thickness frequency distribution of the sunscreen film is also responsible for and can explain the divergence in the measured SPF. For this, we developed a method to measure film thickness from the difference of topography before and after application of 2 mg/cm2 of sunscreen on pig ear epidermal membrane. The influence of five vehicle formulations and of application pressure and spreading time on mean thickness (S), S to median ratio, and SPF in vitro was investigated. The vehicle had a significant impact, low vehicle viscosity resulting in a smaller S, larger S to median ratio, and lower SPF in vitro than high viscosity; continuous oil phase produced the largest S and SPF values. A long spreading time reduced S and SPF and increased application pressure reduced SPF. There was a positive correlation between S and SPF in vitro, underlining the relevance of film thickness for interpreting UV protection differences of formulations with the same filter composition. This work demonstrated a strong influence of vehicle and application conditions on sunscreen efficacy arising from differences in film thickness distribution.

  9. Electronic Absolute Cartesian Autocollimator

    NASA Technical Reports Server (NTRS)

    Leviton, Douglas B.

    2006-01-01

    An electronic absolute Cartesian autocollimator performs the same basic optical function as does a conventional all-optical or a conventional electronic autocollimator but differs in the nature of its optical target and the manner in which the position of the image of the target is measured. The term absolute in the name of this apparatus reflects the nature of the position measurement, which, unlike in a conventional electronic autocollimator, is based absolutely on the position of the image rather than on an assumed proportionality between the position and the levels of processed analog electronic signals. The term Cartesian in the name of this apparatus reflects the nature of its optical target. Figure 1 depicts the electronic functional blocks of an electronic absolute Cartesian autocollimator along with its basic optical layout, which is the same as that of a conventional autocollimator. Referring first to the optical layout and functions only, this or any autocollimator is used to measure the compound angular deviation of a flat datum mirror with respect to the optical axis of the autocollimator itself. The optical components include an illuminated target, a beam splitter, an objective or collimating lens, and a viewer or detector (described in more detail below) at a viewing plane. The target and the viewing planes are focal planes of the lens. Target light reflected by the datum mirror is imaged on the viewing plane at unit magnification by the collimating lens. If the normal to the datum mirror is parallel to the optical axis of the autocollimator, then the target image is centered on the viewing plane. Any angular deviation of the normal from the optical axis manifests itself as a lateral displacement of the target image from the center. The magnitude of the displacement is proportional to the focal length and to the magnitude (assumed to be small) of the angular deviation. The direction of the displacement is perpendicular to the axis about which the

  10. Genome-Wide Association Study of Absolute QRS Voltage Identifies Common Variants of TBX3 as Genetic Determinants of Left Ventricular Mass in a Healthy Japanese Population

    PubMed Central

    Sano, Motoaki; Kamitsuji, Shigeo; Kamatani, Naoyuki; Tabara, Yasuharu; Kawaguchi, Takahisa; Matsuda, Fumihiko; Yamagishi, Hiroyuki; Fukuda, Keiichi

    2016-01-01

    Left ventricular hypertrophy (LVH) represents a common final pathway leading to heart failure. We have searched for genetic determinants of left ventricular (LV) mass using values for absolute electrocardiographic QRS voltage in a healthy Japanese population. After adjusting for covariates, the corrected S and R wave voltages in leads V1 and V5 from 2,994 healthy volunteers in the Japan Pharmacogenomics Data Science Consortium (JPDSC) database were subjected to a genome-wide association study. Potential associations were validated by an in silico replication study using an independent Japanese population obtained from the Nagahama Prospective Genome Cohort for Comprehensive Human Bioscience. We identified a novel association between the lead V5, R wave voltage in Japanese individuals and SNP rs7301743[G], which maps near the gene encoding T-box transcription factor Tbx3. Meta-analysis of two independent Japanese datasets demonstrated a marginally significant association of SNP rs7301743 in TBX3|MED13L with a 0.071 mV (95% CI, 0.038–0.11 mV) shorter R wave amplitude in the V5 lead per minor allele copy (P = 7.635 x 10−8). The transcriptional repressor, TBX3, is proposed to suppress the development of working ventricular myocardium. Our findings suggest that genetic variation of Tbx3 is associated with LV mass in a healthy Japanese population. PMID:27195777

  11. Optomechanics for absolute rotation detection

    NASA Astrophysics Data System (ADS)

    Davuluri, Sankar

    2016-07-01

    In this article, we present an application of optomechanical cavity for the absolute rotation detection. The optomechanical cavity is arranged in a Michelson interferometer in such a way that the classical centrifugal force due to rotation changes the length of the optomechanical cavity. The change in the cavity length induces a shift in the frequency of the cavity mode. The phase shift corresponding to the frequency shift in the cavity mode is measured at the interferometer output to estimate the angular velocity of absolute rotation. We derived an analytic expression to estimate the minimum detectable rotation rate in our scheme for a given optomechanical cavity. Temperature dependence of the rotation detection sensitivity is studied.

  12. Determining XV-15 aeroelastic modes from flight data with frequency-domain methods

    NASA Technical Reports Server (NTRS)

    Acree, C. W., Jr.; Tischler, Mark B.

    1993-01-01

    The XV-15 tilt-rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier transformed). All spectral data were computed using chirp z-transforms. Modal frequencies and damping were determined by fitting curves to frequency-response magnitude and phase data. The results given in this report are for the XV-15 with its original metal rotor blades. Also, frequency and damping values are compared with theoretical predictions made using two different programs, CAMRAD and ASAP. The frequency-domain data-analysis method proved to be very reliable and adequate for tracking aeroelastic modes during flight-envelope expansion. This approach required less flight-test time and yielded mode estimations that were more repeatable, compared with the exponential-decay method previously used.

  13. Methods to calibrate the absolute receive sensitivity of single-element, focused transducers

    PubMed Central

    Rich, Kyle T.; Mast, T. Douglas

    2015-01-01

    Absolute pressure measurements of acoustic emissions by single-element, focused passive cavitation detectors would be facilitated by improved wideband receive calibration techniques. Here, calibration methods were developed to characterize the absolute, frequency-dependent receive sensitivity of a spherically focused, single-element transducer using pulse-echo and pitch-catch techniques. Validation of these calibration methods on a focused receiver were made by generating a pulse from a small diameter source at the focus of the transducer and comparing the absolute pressure measured by a calibrated hydrophone to that of the focused transducer using the receive sensitivities determined here. PMID:26428812

  14. Methods to calibrate the absolute receive sensitivity of single-element, focused transducers.

    PubMed

    Rich, Kyle T; Mast, T Douglas

    2015-09-01

    Absolute pressure measurements of acoustic emissions by single-element, focused passive cavitation detectors would be facilitated by improved wideband receive calibration techniques. Here, calibration methods were developed to characterize the absolute, frequency-dependent receive sensitivity of a spherically focused, single-element transducer using pulse-echo and pitch-catch techniques. Validation of these calibration methods on a focused receiver were made by generating a pulse from a small diameter source at the focus of the transducer and comparing the absolute pressure measured by a calibrated hydrophone to that of the focused transducer using the receive sensitivities determined here. PMID:26428812

  15. Absolute nuclear material assay

    DOEpatents

    Prasad, Manoj K.; Snyderman, Neal J.; Rowland, Mark S.

    2012-05-15

    A method of absolute nuclear material assay of an unknown source comprising counting neutrons from the unknown source and providing an absolute nuclear material assay utilizing a model to optimally compare to the measured count distributions. In one embodiment, the step of providing an absolute nuclear material assay comprises utilizing a random sampling of analytically computed fission chain distributions to generate a continuous time-evolving sequence of event-counts by spreading the fission chain distribution in time.

  16. Absolute nuclear material assay

    DOEpatents

    Prasad, Manoj K.; Snyderman, Neal J.; Rowland, Mark S.

    2010-07-13

    A method of absolute nuclear material assay of an unknown source comprising counting neutrons from the unknown source and providing an absolute nuclear material assay utilizing a model to optimally compare to the measured count distributions. In one embodiment, the step of providing an absolute nuclear material assay comprises utilizing a random sampling of analytically computed fission chain distributions to generate a continuous time-evolving sequence of event-counts by spreading the fission chain distribution in time.

  17. Frequency-response method for determination of dynamic stability characteristics of airplanes with automatic controls

    NASA Technical Reports Server (NTRS)

    Greenberg, Harry

    1947-01-01

    A frequency-response method for determining the critical control-gearing and hunting oscillations of airplanes with automatic pilots is presented. The method is graphical and has several advantages over the standard numerical procedure based on Routh's discriminant. The chief advantage of the method is that direct use can be made of the measured response characteristics of the automatic pilot. This feature is especially useful in determining the existence, amplitude, and frequency of the hunting oscillations that may be present when the automatic pilot has nonlinear dynamic characteristics. Several examples are worked out to illustrate the application of the frequency-response method in determining the effect of automatic-pilot lag or lead on critical control gearing and in determining the amplitude and frequency hunting. It is shown that the method may be applied to the case of a control geared to airplane motions about two axes.

  18. Interface resistance in copper coated carbon determined by frequency dependent photothermal radiometry

    NASA Astrophysics Data System (ADS)

    Kijamnajsuk, P.; Giuliani, F.; Chirtoc, M.; Horny, N.; Gibkes, J.; Chotikaprakhan, S.; Bein, B. K.; Pelzl, J.

    2010-03-01

    The heat transfer in copper-carbon flat model systems was studied by frequency dependent photothermal radiometry. A novel approach which relies on the frequency dependence of the photothermal signal phase and amplitude at intermediate frequencies was introduced to determine the thermal interface resistance between the Cu-film and the substrate. The frequency dependent amplitude and phase of the photothermal signals were analyzed in the frame of a model of a one- dimensional heat flow perpendicular to the film plane. The interface resistance of the investigated CuC-sample with a Ti-bonding layer was found to increase by a factor two on heat treatment.

  19. The determination of Schumann resonance mode frequencies using iterative procedure of complex demodulation

    NASA Astrophysics Data System (ADS)

    Ondrášková, Adriena; Ševčík, Sebastian

    2013-12-01

    The more precise determination of instantaneous peak frequency of Schumann resonance (SR) modes, especially based on relatively short signal sequences, seems to be important for detailed analysis of SR modal frequencies variations. Contrary to commonly used method of obtaining modal frequencies by Lorentzian fitting of DFT spectra, the attempt was made to employ the complex demodulation method in iterated form. The results for SR signals contaminated with low-frequency noise and hum in various degree as well as the comparison with standard method are presented. Real signals of vertical electric field component picked up at the Astronomical and Geophysical Observatory of Comenius University at Modra, Slovakia, were the primary sources.

  20. Under proper control, oxidation of proteins with known chemical structure provides an accurate and absolute method for the determination of their molar concentration.

    PubMed

    Guermant, C; Azarkan, M; Smolders, N; Baeyens-Volant, D; Nijs, M; Paul, C; Brygier, J; Vincentelli, J; Looze, Y

    2000-01-01

    Oxidation at 120 degrees C of inorganic and organic (including amino acids, di- and tripeptides) model compounds by K(2)Cr(2)O(7) in the presence of H(2)SO(4) (mass fraction: 0.572), Ag(2)SO(4) (catalyst), and HgSO(4) results in the quantitative conversion of their C-atoms into CO(2) within 24 h or less. Under these stressed, well-defined conditions, the S-atoms present in cysteine and cystine residues are oxidized into SO(3) while, interestingly, the oxidation states of all the other (including the N-) atoms normally present in a protein do remain quite unchanged. When the chemical structure of a given protein is available, the total number of electrons the protein is able to transfer to K(2)Cr(2)O(7) and thereof, the total number of moles of Cr(3+) ions which the protein is able to generate upon oxidation can be accurately calculated. In such cases, unknown protein molar concentrations can thus be determined through straightforward spectrophotometric measurements of Cr(3+) concentrations. The values of molar absorption coefficients for several well-characterized proteins have been redetermined on this basis and observed to be in excellent agreement with the most precise values reported in the literature, which fully assesses the validity of the method. When applied to highly purified proteins of known chemical structure (more generally of known atomic composition), this method is absolute and accurate (+/-1%). Furthermore, it is well adapted to series measurements since available commercial kits for chemical oxygen demand (COD) measurements can readily be adapted to work under the experimental conditions recommended here for the protein assay. PMID:10610688

  1. Absolute Determination for the Sodium-22(p,gamma)Magnesium-23 Reaction Rate: Consequences for Nucleosynthesis of Sodium-22 in Novae

    NASA Astrophysics Data System (ADS)

    Sallaska, Anne L.

    2010-11-01

    Hydrodynamic simulations of classical novae on ONe white dwarfs predict substantial production of 22Na. Observation of 22Na decay should be correlated with the corresponding nova because the half life of 22Na is only 2.6 years. The 1275-keV gamma ray from the beta decay of 22Na is, therefore, an excellent diagnostic for the nova phenomenon and a long-sought target of gamma-ray telescopes. Nova simulations determine the maximum 22Na-detection distance to be < 1 kpc for the INTEGRAL spectrometer SPI, consistent with its non-observation to date. However, model estimates are strongly dependent on the thermonuclear rate of the 22Na(p, gamma)23Mg reaction, which is the main destruction mechanism of 22Na in novae. The 22Na(p,gamma)23Mg rate is expected to be dominated by narrow, isolated resonances with Ep < 300 key. The currently employed rate is based on a single set of absolute resonance-strength measurements with Ep ≥ 290 keV, and one relative measurement of resonances with Ep ≥ 214 keV. Recently, a new level has been found in 23Mg which would correspond to a resonance at Ep = 198 keV that might dominate the reaction rate at nova temperatures. We have measured the 22Na(p, gamma) 23Mg resonance strengths directly and absolutely, in addition to resonance energies and branches. Proton beams were produced at the University of Washington and delivered to a specially designed beam line that included rastering and cold vacuum protection of the 22Na-implanted targets (fabricated at TRIUMF-ISAC). Two high-purity germanium detectors were employed and surrounded by anticoincidence shields to reduce cosmic backgrounds. Measurements were made on known 22Na+p resonances, which we observed at laboratory energies Ep = 213, 288, 454, 610 keV and on proposed resonances at Ep = 198, 209, and 232 key. The proposed resonances were not observed, and the upper limit placed on the 198-keV resonance strength indicates that the resonance at Ep = 213 keV still dominates the reaction rate

  2. Absolute determination of single-stranded and self-complementary adeno-associated viral vector genome titers by droplet digital PCR.

    PubMed

    Lock, Martin; Alvira, Mauricio R; Chen, Shu-Jen; Wilson, James M

    2014-04-01

    Accurate titration of adeno-associated viral (AAV) vector genome copies is critical for ensuring correct and reproducible dosing in both preclinical and clinical settings. Quantitative PCR (qPCR) is the current method of choice for titrating AAV genomes because of the simplicity, accuracy, and robustness of the assay. However, issues with qPCR-based determination of self-complementary AAV vector genome titers, due to primer-probe exclusion through genome self-annealing or through packaging of prematurely terminated defective interfering (DI) genomes, have been reported. Alternative qPCR, gel-based, or Southern blotting titering methods have been designed to overcome these issues but may represent a backward step from standard qPCR methods in terms of simplicity, robustness, and precision. Droplet digital PCR (ddPCR) is a new PCR technique that directly quantifies DNA copies with an unparalleled degree of precision and without the need for a standard curve or for a high degree of amplification efficiency; all properties that lend themselves to the accurate quantification of both single-stranded and self-complementary AAV genomes. Here we compare a ddPCR-based AAV genome titer assay with a standard and an optimized qPCR assay for the titration of both single-stranded and self-complementary AAV genomes. We demonstrate absolute quantification of single-stranded AAV vector genomes by ddPCR with up to 4-fold increases in titer over a standard qPCR titration but with equivalent readout to an optimized qPCR assay. In the case of self-complementary vectors, ddPCR titers were on average 5-, 1.9-, and 2.3-fold higher than those determined by standard qPCR, optimized qPCR, and agarose gel assays, respectively. Droplet digital PCR-based genome titering was superior to qPCR in terms of both intra- and interassay precision and is more resistant to PCR inhibitors, a desirable feature for in-process monitoring of early-stage vector production and for vector genome biodistribution

  3. Determinants of frequency long-term facilitation following acute intermittent hypoxia in vagotomized rats.

    PubMed

    Baker-Herman, Tracy L; Mitchell, Gordon S

    2008-06-30

    Acute intermittent (AIH), but not acute sustained hypoxia (ASH) elicits a form of respiratory plasticity known as long-term facilitation (LTF). In anesthetized rats, LTF is expressed as increased respiratory-related nerve burst amplitude, with variable effects on burst frequency. We analyzed a large data set from multiple investigators using the same experimental protocol to determine factors influencing frequency LTF. Our meta-analysis revealed that AIH elicits both phrenic amplitude and frequency LTF in anesthetized and vagotomized rats, but frequency LTF is small in comparison with amplitude LTF (12% versus 60%, respectively). ASH elicits a small, but significant frequency and amplitude LTF (8% and 10%, respectively) that is not significantly different than controls. Similar to all published reports, analysis of this large data set confirms that phrenic amplitude LTF following AIH is significantly greater than ASH. Multiple regression analysis revealed a strong correlation between baseline burst frequency and frequency LTF. Variations in baseline burst frequency may contribute to variation in frequency LTF and may underlie the apparent effects of some drug treatments. PMID:18450525

  4. Determinants of frequency long-term facilitation following acute intermittent hypoxia in vagotomized rats

    PubMed Central

    Baker-Herman, Tracy L.; Mitchell, Gordon S.

    2008-01-01

    Acute intermittent (AIH), but not acute sustained hypoxia (ASH) elicits a form of respiratory plasticity known as long-term facilitation (LTF). In anesthetized rats, LTF is expressed as increased respiratory-related nerve burst amplitude, with variable effects on burst frequency. We analyzed a large data set from multiple investigators using the same experimental protocol to determine factors influencing frequency LTF. Our meta-analysis revealed that AIH elicits both phrenic amplitude and frequency LTF in anesthetized and vagotomized rats, but frequency LTF is small in comparison with amplitude LTF (12% versus 60%, respectively). ASH elicits a small, but significant frequency and amplitude LTF (8% and 10%, respectively) that is not significantly different than controls. Similar to all published reports, analysis of this large data set confirms that phrenic amplitude LTF following AIH is significantly greater than ASH. Multiple regression analysis revealed a strong correlation between baseline burst frequency and frequency LTF. Variations in baseline burst frequency may contribute to variation in frequency LTF and may underlie the apparent effects of some drug treatments. PMID:18450525

  5. An automatic method to determine cutoff frequency based on image power spectrum

    SciTech Connect

    Beis, J.S.; Celler, A.; Barney, J.S.

    1995-12-01

    The authors present an algorithm for automatically choosing filter cutoff frequency (F{sub c}) using the power spectrum of the projections. The method is based on the assumption that the expectation of the image power spectrum is the sum of the expectation of the blurred object power spectrum (dominant at low frequencies) plus a constant value due to Poisson noise. By considering the discrete components of the noise-dominated high-frequency spectrum as a Gaussian distribution N({mu},{sigma}), the Student t-test determines F{sub c} as the highest frequency for which the image frequency components are unlikely to be drawn from N ({mu},{sigma}). The method is general and can be applied to any filter. In this work, the authors tested the approach using the Metz restoration filter on simulated, phantom, and patient data with good results. Quantitative performance of the technique was evaluated by plotting recovery coefficient (RC) versus NMSE of reconstructed images.

  6. Reliable and integrated technique for determining resonant frequency in radio frequency resonators. Application to a high-precision resonant cavity-based displacement sensor

    NASA Astrophysics Data System (ADS)

    Jauregui, Rigoberto; Asua, Estibaliz; Portilla, Joaquin; Etxebarria, Victor

    2015-03-01

    This paper presents a reliable and integrated technique for determining the resonant frequency of radio frequency resonators, which can be of interest for different purposes. The approach uses a heterodyne scheme as phase detector coupled to a voltage-controlled oscillator. The system seeks the oscillator frequency that produces a phase null in the resonator, which corresponds to the resonant frequency. A complete explanation of the technique to determine the resonant frequency is presented and experimentally tested. The method has been applied to a high-precision displacement sensor based on resonant cavity, obtaining a theoretical nanometric precision.

  7. Liquid-filled transient pressure measuring systems: A method for determining frequency response

    NASA Technical Reports Server (NTRS)

    Anderson, R. C.; Englund, D. R., Jr.

    1971-01-01

    An equation is given and experimentally verified for computing the resonant frequency of liquid-filled transient pressure measuring systems. Resonant frequencies of 100 to 1000 Hz are typical of those systems tested. The effect of noncondensable gas bubbles on system response is described. A method for determining transducer volumetric compliance is presented. An example system is described and analyzed to demonstrate the use of the theory.

  8. Absolute neutrino mass measurements

    NASA Astrophysics Data System (ADS)

    Wolf, Joachim

    2011-10-01

    The neutrino mass plays an important role in particle physics, astrophysics and cosmology. In recent years the detection of neutrino flavour oscillations proved that neutrinos carry mass. However, oscillation experiments are only sensitive to the mass-squared difference of the mass eigenvalues. In contrast to cosmological observations and neutrino-less double beta decay (0v2β) searches, single β-decay experiments provide a direct, model-independent way to determine the absolute neutrino mass by measuring the energy spectrum of decay electrons at the endpoint region with high accuracy. Currently the best kinematic upper limits on the neutrino mass of 2.2eV have been set by two experiments in Mainz and Troitsk, using tritium as beta emitter. The next generation tritium β-experiment KATRIN is currently under construction in Karlsruhe/Germany by an international collaboration. KATRIN intends to improve the sensitivity by one order of magnitude to 0.2eV. The investigation of a second isotope (137Rh) is being pursued by the international MARE collaboration using micro-calorimeters to measure the beta spectrum. The technology needed to reach 0.2eV sensitivity is still in the R&D phase. This paper reviews the present status of neutrino-mass measurements with cosmological data, 0v2β decay and single β-decay.

  9. Absolute neutrino mass measurements

    SciTech Connect

    Wolf, Joachim

    2011-10-06

    The neutrino mass plays an important role in particle physics, astrophysics and cosmology. In recent years the detection of neutrino flavour oscillations proved that neutrinos carry mass. However, oscillation experiments are only sensitive to the mass-squared difference of the mass eigenvalues. In contrast to cosmological observations and neutrino-less double beta decay (0v2{beta}) searches, single {beta}-decay experiments provide a direct, model-independent way to determine the absolute neutrino mass by measuring the energy spectrum of decay electrons at the endpoint region with high accuracy.Currently the best kinematic upper limits on the neutrino mass of 2.2eV have been set by two experiments in Mainz and Troitsk, using tritium as beta emitter. The next generation tritium {beta}-experiment KATRIN is currently under construction in Karlsruhe/Germany by an international collaboration. KATRIN intends to improve the sensitivity by one order of magnitude to 0.2eV. The investigation of a second isotope ({sup 137}Rh) is being pursued by the international MARE collaboration using micro-calorimeters to measure the beta spectrum. The technology needed to reach 0.2eV sensitivity is still in the R and D phase. This paper reviews the present status of neutrino-mass measurements with cosmological data, 0v2{beta} decay and single {beta}-decay.

  10. Frequency determination of visible laser light by interferometric comparison with upconverted CO(2) laser radiation.

    PubMed

    Woods, P T; Shotton, K C; Rowley, W R

    1978-04-01

    A servocontrolled 1-m plane-parallel Fabry-Perot interferometer has been developed at NPL for the precise intercomparison of laser wavelengths. This instrument has been used to measure the wavelength ratio of a 679-nm radiation and that from a 633-nm iodine-stabilized He-Ne laser, achieving an accuracy of 2.9 parts in 10(11). The 679-nm light was derived from a stabilized CO(2) laser radiation by upconversion, and the wavelength of this 9.3-microm laser radiation can be calculated from the visible wavelength result. Frequency measurements on the same CO(2) laser radiation have already been made in this laboratory, so that the experiment reported here leads to a precise value for the speed of light in vacuum and to the value of 473, 612, 380.5 +/- 0.3 MHz for the absolute frequency of the visible radiation from a He-Ne laser stabilized to component d of (127)I(2). PMID:20197930

  11. Absolute biological needs.

    PubMed

    McLeod, Stephen

    2014-07-01

    Absolute needs (as against instrumental needs) are independent of the ends, goals and purposes of personal agents. Against the view that the only needs are instrumental needs, David Wiggins and Garrett Thomson have defended absolute needs on the grounds that the verb 'need' has instrumental and absolute senses. While remaining neutral about it, this article does not adopt that approach. Instead, it suggests that there are absolute biological needs. The absolute nature of these needs is defended by appeal to: their objectivity (as against mind-dependence); the universality of the phenomenon of needing across the plant and animal kingdoms; the impossibility that biological needs depend wholly upon the exercise of the abilities characteristic of personal agency; the contention that the possession of biological needs is prior to the possession of the abilities characteristic of personal agency. Finally, three philosophical usages of 'normative' are distinguished. On two of these, to describe a phenomenon or claim as 'normative' is to describe it as value-dependent. A description of a phenomenon or claim as 'normative' in the third sense does not entail such value-dependency, though it leaves open the possibility that value depends upon the phenomenon or upon the truth of the claim. It is argued that while survival needs (or claims about them) may well be normative in this third sense, they are normative in neither of the first two. Thus, the idea of absolute need is not inherently normative in either of the first two senses. PMID:23586876

  12. What Determines the Speed of Lexical Access: Homophone or Specific-Word Frequency? A Reply to Jescheniak et al. (2003)

    ERIC Educational Resources Information Center

    Caramazza, Alfonso; Bi, Yanchao; Costa, Albert; Miozzo, Michelle

    2004-01-01

    A. Caramazza, A. Costa, M. Miozzo, and Y. Bi (2001) reported a series of experiments showing that naming latencies for homophones are determined by specific-word frequency (e.g., frequency of nun) and not homophone frequency (frequency of nun + none). J. D. Jescheniak, A. S. Meyer, and W. J. M. Levelt (2003) have challenged these studies on a…

  13. Magnetoresistive polyaniline-silicon carbide metacomposites: plasma frequency determination and high magnetic field sensitivity.

    PubMed

    Gu, Hongbo; Guo, Jiang; Khan, Mojammel Alam; Young, David P; Shen, T D; Wei, Suying; Guo, Zhanhu

    2016-07-20

    The Drude model modified by Debye relaxation time was introduced to determine the plasma frequency (ωp) in the surface initiated polymerization (SIP) synthesized β-silicon carbide (β-SiC)/polyaniline (PANI) metacomposites. The calculated plasma frequency for these metacomposites with different loadings of β-SiC nanoparticles was ranging from 6.11 × 10(4) to 1.53 × 10(5) rad s(-1). The relationship between the negative permittivity and plasma frequency indicates the existence of switching frequency, at which the permittivity was changed from negative to positive. More interestingly, the synthesized non-magnetic metacomposites, observed to follow the 3-dimensional (3-D) Mott variable range hopping (VRH) electrical conduction mechanism, demonstrated high positive magnetoresistance (MR) values of up to 57.48% and high MR sensitivity at low magnetic field regimes. PMID:27386820

  14. Combined Absolute/Relative Hypocenter Determination and Moment Tensor Inversion of a VT-B Event Cluster Before the 1998 Eruption of the Mt. Merapi Volcano (Java)

    NASA Astrophysics Data System (ADS)

    Wassermann, J.; Krüger, F.

    2001-12-01

    In the ongoing Indonesian-German MERAPI project the seismic signals at Merapi volcano are recorded continuously since July 1997 with a combined seismic network-array approach. With this network it was possible to record the seismicity before the onset of the eruption in July 1998 with a high dynamic and broad frequency range. The automatic standard analysis of the recorded seismic data before the first of two larger pyroclastic density flows emphasized the importance of a seismic swarm of VT-B type events in order to forecast the location of the newly formed lava lobe during this eruptive phase. To improve the location accuracy, we relocate these events using an extended cluster analysis technique. We first estimate the amount of events in three different seismic clusters. After this we estimate the relative onset times of all event combinations within one cluster using the SmoothedCOherencyTransform algorithm. Further we use the amplitude of the computed cross-correlation coefficients of each event-event waveform pair to further restrict our hypocenter constrain. In the final step we invert iteratively all estimated travel times, the relative travel times within the different arrays and the correlation coefficients in one single matrix. The resulting high precision hypocenter determination of the distinct clusters indicate a small source volume in the intersection of a old crater floor and the active part of Mt. Merapi. The high precision in hypocenter determination make a detailed analysis of the source mechanisms of these VTB events feasible. We use a point source full moment tensor inversion and simple source time functions to invert for the source mechanism. Greens functions are calculated with the reflectivity method and local 1D models based on refraction on different scales. The bias in the results due to not modelled topography and 3D-structure is estimated using a bootstrap approach.

  15. Synthesis and determination of the absolute configuration of (−)-(5R,6Z)-dendrolasin-5-acetate from the nudibranch Hypselodoris jacksoni

    PubMed Central

    Mudianta, I Wayan; Challinor, Victoria L; Winters, Anne E; Cheney, Karen L; De Voss, James J

    2013-01-01

    Summary A small sample of (−)-(5R,6Z)-dendrolasin-5-acetate, which was fully characterized by 2D NMR studies, was isolated from the nudibranch Hypselodoris jacksoni, along with the sesquiterpenes (+)-agassizin, (−)-furodysinin, (−)-euryfuran, (−)-dehydroherbadysidolide and (+)-pallescensone. A synthetic sample ([α]D −8.7) of the new metabolite was prepared by [1,2]-Wittig rearrangement of a geranylfuryl ether followed by acetylation of purified alcohol isomers. The absolute configuration at C-5 was established as R by the analysis of MPA ester derivatives of (Z)-5-hydroxydendrolasin obtained by preparative enantioselective HPLC. PMID:24454572

  16. Project 8: Determining neutrino mass from tritium beta decay using a frequency-based method

    SciTech Connect

    Doe, Peter J.; Kofron, Jared N.; MCBride, Lisa; Robertson, R. G. H.; Rosenberg, Leslie; Rybka, Gray; Doelman, S.; Rogers, Alan E.; Formaggio, Joseph; Furse, Daniel; Oblath, Noah S.; LaRoque, Benjamin; Leber, Michelle; Monreal, Ben; Bahr, Matthew; Asner, David M.; Jones, Anthony M.; Fernandes, Justin L.; VanDevender, Brent A.; Patterson, Ryan B.; Bradley, Rich; Thummler, Thomas

    2013-10-04

    A general description is given of Project 8, a new approach to measuring the neutrino mass scale via the beta decay of tritium. In Project 8, the energy of electrons emitted in beta decay is determined from the frequency of cyclotron radiation emitted as the electrons spiral in a uniform magnetic field

  17. Methods to Use Surface Infiltration Tests in Permeable Pavement Systems to Determine Maintenance Frequency

    EPA Science Inventory

    Currently, there is limited guidance on selecting test sites to measure surface infiltration rates in permeable pavement systems to determine maintenance frequency. The ASTM method (ASTM C1701) for measuring infiltration rate of in-place pervious concrete suggest to either (1) p...

  18. Frequency analysis of aquatic habitat: a procedure for determining instream flow needs

    SciTech Connect

    Sale, M.J.; Railsback, S.F.; Herricks, E.E.

    1981-01-01

    Minimum flow recommendations can be improved by analyzing the natural habitat variability in lotic environments. Habitat modeling techniques such as the Incremental Methodology can be combined with stream flow records to generate habitat frequency curves that are useful in determining instream flow needs.

  19. Absolute instability of the Gaussian wake profile

    NASA Technical Reports Server (NTRS)

    Hultgren, Lennart S.; Aggarwal, Arun K.

    1987-01-01

    Linear parallel-flow stability theory has been used to investigate the effect of viscosity on the local absolute instability of a family of wake profiles with a Gaussian velocity distribution. The type of local instability, i.e., convective or absolute, is determined by the location of a branch-point singularity with zero group velocity of the complex dispersion relation for the instability waves. The effects of viscosity were found to be weak for values of the wake Reynolds number, based on the center-line velocity defect and the wake half-width, larger than about 400. Absolute instability occurs only for sufficiently large values of the center-line wake defect. The critical value of this parameter increases with decreasing wake Reynolds number, thereby indicating a shrinking region of absolute instability with decreasing wake Reynolds number. If backflow is not allowed, absolute instability does not occur for wake Reynolds numbers smaller than about 38.

  20. Synthesis and determination of absolute configuration of a non-peptidic αvβ6 integrin antagonist for the treatment of idiopathic pulmonary fibrosis.

    PubMed

    Anderson, Niall A; Campbell, Ian B; Fallon, Brendan J; Lynn, Sean M; Macdonald, Simon J F; Pritchard, John M; Procopiou, Panayiotis A; Sollis, Steven L; Thorp, Lee R

    2016-07-01

    A diastereoselective synthesis of (S)-3-(3-(3,5-dimethyl-1H-pyrazol-1-yl)phenyl)-4-((R)-3-(2-(5,6,7,8-tetrahydro-1,8-naphthyridin-2-yl)ethyl)pyrrolidin-1-yl)butanoic acid (1), a potential therapeutic agent for the treatment of Idiopathic Pulmonary Fibrosis, which is currently undergoing Phase I clinical trials is reported. The key steps in the synthesis involved alkylation of 2-methylnaphthyridine with (R)-N-Boc-3-(iodomethyl)-pyrrolidine, and an asymmetric Rh-catalysed addition of an arylboronic acid to a 4-(N-pyrrolidinyl)crotonate ester. The overall yield of the seven linear step synthesis was 8% and the product was obtained in >99.5% ee proceeding with 80% de. The absolute configuration of 1 was established by an alternative asymmetric synthesis involving alkylation of an arylacetic acid using Evans oxazolidinone chemistry, acylation using the resulting 2-arylsuccinic acid, and reduction. The absolute configuration of the benzylic asymmetric centre was established as (S). PMID:27226381

  1. The absolute path command

    2012-05-11

    The ap command traveres all symlinks in a given file, directory, or executable name to identify the final absolute path. It can print just the final path, each intermediate link along with the symlink chan, and the permissions and ownership of each directory component in the final path. It has functionality similar to "which", except that it shows the final path instead of the first path. It is also similar to "pwd", but it canmore » provide the absolute path to a relative directory from the current working directory.« less

  2. The absolute path command

    SciTech Connect

    Moody, A.

    2012-05-11

    The ap command traveres all symlinks in a given file, directory, or executable name to identify the final absolute path. It can print just the final path, each intermediate link along with the symlink chan, and the permissions and ownership of each directory component in the final path. It has functionality similar to "which", except that it shows the final path instead of the first path. It is also similar to "pwd", but it can provide the absolute path to a relative directory from the current working directory.

  3. Determination of permethrin resistance allele frequency of human head louse populations by quantitative sequencing.

    PubMed

    Kwon, Deok Ho; Yoon, Kyong Sup; Strycharz, Joseph P; Clark, J Marshall; Lee, Si Hyeock

    2008-09-01

    A quantitative sequencing (QS) protocol that detects the frequencies of sodium channel mutations (M815I, T917I, and L920F) responsible for knockdown resistance in permethrin-resistant head lice (Pediculus humanus capitis De Geer) was tested as a population genotyping method for use as a preliminary resistance monitoring tool. Genomic DNA fragments of the sodium channel a-subunit gene that encompass the three mutation sites were polymerase chain reaction (PCR)-1 amplified from individual head lice with either resistant or susceptible genotypes, and combined in various ratios to generate standard DNA template mixtures for QS. After sequencing, the signal ratios between resistant and susceptible nucleotides were calculated and plotted against the corresponding resistance allele frequencies. Quadratic regression coefficients of the plots were close to 1, demonstrating that the signal ratios are highly correlated with the resistance allele frequencies. Resistance allele frequencies predicted by QS, using either "pooled DNA" (DNA extracted from individual louse specimens and pooled) or "pooled specimen DNA" (DNA simultaneously extracted from multiple louse specimens), agreed well with those determined by individual sequencing, confirming the reliability and accuracy of QS as a population genotyping method and validating our approach of using the pooled specimen DNA as the DNA template for QS. Our protocol for QS was determined to be highly reliable for the prediction of resistance allele frequencies higher than approximately 7.4% at the 95% confidence level. According to the resistance allele frequencies determined by QS, pyrethroid resistance varies substantially among different geographical regions, emphasizing the importance of early resistance detection and proper management strategies. PMID:18826035

  4. Dynamics of neuromodulatory feedback determines frequency modulation in a reduced respiratory network: a computational study.

    PubMed

    Toporikova, Natalia; Butera, Robert J

    2013-02-01

    Neuromodulators, such as amines and neuropeptides, alter the activity of neurons and neuronal networks. In this work, we investigate how neuromodulators, which activate G(q)-protein second messenger systems, can modulate the bursting frequency of neurons in a critical portion of the respiratory neural network, the pre-Bötzinger complex (preBötC). These neurons are a vital part of the ponto-medullary neuronal network, which generates a stable respiratory rhythm whose frequency is regulated by neuromodulator release from the nearby Raphe nucleus. Using a simulated 50-cell network of excitatory preBötC neurons with a heterogeneous distribution of persistent sodium conductance and Ca(2+), we determined conditions for frequency modulation in such a network by simulating interaction between Raphe and preBötC nuclei. We found that the positive feedback between the Raphe excitability and preBötC activity induces frequency modulation in the preBötC neurons. In addition, the frequency of the respiratory rhythm can be regulated via phasic release of excitatory neuromodulators from the Raphe nucleus. We predict that the application of a G(q) antagonist will eliminate this frequency modulation by the Raphe and keep the network frequency constant and low. In contrast, application of a G(q) agonist will result in a high frequency for all levels of Raphe stimulation. Our modeling results also suggest that high [K(+)] requirement in respiratory brain slice experiments may serve as a compensatory mechanism for low neuromodulatory tone. PMID:23202052

  5. Spectroscopic Pulsational Frequency and Mode Determination of the γ Doradus Star HD 189631

    NASA Astrophysics Data System (ADS)

    Davie, M. W.; Pollard, K. R.; Cottrell, P. L.; Brunsden, E.; Wright, D. J.; De Cat, P.

    We present improvement and confirmation of identified frequencies and pulsation modes for the γ Doradus star HD 189631. This work improves upon previous studies by incorporating a significant number of additional spectra and precise determination of frequencies. Four frequencies were identified for this star: 1.6774 ± 0.0002 d-1, 1.4174 ± 0.0002 d-1, 0.0714 ± 0.0002 d-1, and 1.8228 ± 0.0002 d-1 which were identified with the modes (l,m) = (1, +1), (1, +1), (2, -2), and (1, +1) respectively. These findings are in agreement with the most recent literature. The prevalence of (l,m) = (1, +1) modes in γ Doradus stars is starting to become apparent and we discuss this result.

  6. Like/dislike analysis using EEG: determination of most discriminative channels and frequencies.

    PubMed

    Yılmaz, Bülent; Korkmaz, Sümeyye; Arslan, Dilek Betül; Güngör, Evrim; Asyalı, Musa H

    2014-02-01

    In this study, we have analyzed electroencephalography (EEG) signals to investigate the following issues, (i) which frequencies and EEG channels could be relatively better indicators of preference (like or dislike decisions) of consumer products, (ii) timing characteristic of "like" decisions during such mental processes. For this purpose, we have obtained multichannel EEG recordings from 15 subjects, during total of 16 epochs of 10 s long, while they were presented with some shoe photographs. When they liked a specific shoe, they pressed on a button and marked the time of this activity and the particular epoch was labeled as a LIKE case. No button press meant that the subject did not like the particular shoe that was displayed and corresponding epoch designated as a DISLIKE case. After preprocessing, power spectral density (PSD) of EEG data was estimated at different frequencies (4, 5, …, 40 Hz) using the Burg method, for each epoch corresponding to one shoe presentation. Each subject's data consisted of normalized PSD values (NPVs) from all LIKE and DISLIKE cases/epochs coming from all 19 EEG channels. In order to determine the most discriminative frequencies and channels, we have utilized logistic regression, where LIKE/DISLIKE status was used as a categorical (binary) response variable and corresponding NPVs were the continuously valued input variables or predictors. We observed that when all the NPVs (total of 37) are used as predictors, the regression problem was becoming ill-posed due to large number of predictors (compared to the number of samples) and high correlation among predictors. To circumvent this issue, we have divided the frequency band into low frequency (LF) 4-19 Hz and high frequency (HF) 20-40 Hz bands and analyzed the influence of the NPV in these bands separately. Then, using the p-values that indicate how significantly estimated predictor weights are different than zero, we have determined the NPVs and channels that are more influential

  7. Evaluation of Hinf I-generated VNTR profile frequencies determined using various ethnic databases.

    PubMed

    Budowle, B; Monson, K L; Giusti, A M; Brown, B L

    1994-07-01

    Concerns have been raised about hypothetical problems arising from the use of statistics for determining the likelihood of occurrence of DNA profiles for forensic purposes. A major contention is that reference databases based on subgroups of a major population category rather than on general (or major) population groups, might yield large differences in the estimated likelihood of occurrence of DNA profiles. This hypothetical issue is based on the assertion by some people that the differences among subgroups within a race would be greater than between races (at least for forensic purposes). To evaluate the effects of the above concern the likelihood of occurrence of 615 Hinf I-generated target DNA profiles was estimated using fixed bin frequencies from various ethnic databases and the multiplication rule. Based on the data in this study, differences in allele frequencies at a particular locus do not have substantial effects on VNTR profile frequency estimates when subgroup reference databases from within a major population group are compared. In contrast, the greatest variation in statistical estimates occurs across-major population groups. Therefore, the assertion, by some critics that the differences among subgroups within a race would be greater than between races (at least for forensic purposes), is unfounded. The data in the study support that comparisons across major population groups provide valid estimates of DNA profile frequencies without forensically significant consequences. The data do not support the need for alternate procedures, such as the ceiling principle approach, for deriving statistical estimates of DNA profile frequencies. PMID:7914910

  8. Comparison of back projection methods of determining earthquake rupture process in time and frequency domains

    NASA Astrophysics Data System (ADS)

    Wang, W.; Wen, L.

    2013-12-01

    Back projection is a method to back project the seismic energy recorded in a seismic array back to the earthquake source region and determine the rupture process of a large earthquake. The method takes advantage of the coherence of seismic energy in a seismic array and is quick in determining some important properties of earthquake source. The method can be performed in both time and frequency domains. In time domain, the most conventional procedure is beam forming with some measures of suppressing the noise, such as the Nth root stacking, etc. In the frequency domain, the multiple signal classification method (MUSIC) estimates the direction of arrivals of multiple waves propagating through an array using the subspace method. The advantage of this method is the ability to study rupture properties at various frequencies and to resolve simultaneous arrivals making it suitable for detecting biliteral rupture of an earthquake source. We present a comparison of back projection results on some large earthquakes between the methods in time domain and frequency domain. The time-domain procedure produces an image that is smeared and exhibits some artifacts, although some enhancing stacking methods can at some extent alleviate the problem. On the other hand, the MUSIC method resolves clear multiple arrivals and provides higher resolution of rupture imaging.

  9. Communication: Probing the absolute configuration of chiral molecules at aqueous interfaces.

    PubMed

    Lotze, Stephan; Versluis, Jan; Olijve, Luuk L C; van Schijndel, Luuk; Milroy, Lech G; Voets, Ilja K; Bakker, Huib J

    2015-11-28

    We demonstrate that the enantiomers of chiral macromolecules at an aqueous interface can be distinguished with monolayer sensitivity using heterodyne-detected vibrational sum-frequency generation (VSFG). We perform VSFG spectroscopy with a polarization combination that selectively probes chiral molecular structures. By using frequencies far detuned from electronic resonances, we probe the chiral macromolecular structures with high surface specificity. The phase of the sum-frequency light generated by the chiral molecules is determined using heterodyne detection. With this approach, we can distinguish right-handed and left-handed helical peptides at a water-air interface. We thus show that heterodyne-detected VSFG is sensitive to the absolute configuration of complex, interfacial macromolecules and has the potential to determine the absolute configuration of enantiomers at interfaces. PMID:26627942

  10. Communication: Probing the absolute configuration of chiral molecules at aqueous interfaces

    NASA Astrophysics Data System (ADS)

    Lotze, Stephan; Versluis, Jan; Olijve, Luuk L. C.; van Schijndel, Luuk; Milroy, Lech G.; Voets, Ilja K.; Bakker, Huib J.

    2015-11-01

    We demonstrate that the enantiomers of chiral macromolecules at an aqueous interface can be distinguished with monolayer sensitivity using heterodyne-detected vibrational sum-frequency generation (VSFG). We perform VSFG spectroscopy with a polarization combination that selectively probes chiral molecular structures. By using frequencies far detuned from electronic resonances, we probe the chiral macromolecular structures with high surface specificity. The phase of the sum-frequency light generated by the chiral molecules is determined using heterodyne detection. With this approach, we can distinguish right-handed and left-handed helical peptides at a water-air interface. We thus show that heterodyne-detected VSFG is sensitive to the absolute configuration of complex, interfacial macromolecules and has the potential to determine the absolute configuration of enantiomers at interfaces.

  11. Communication: Probing the absolute configuration of chiral molecules at aqueous interfaces

    SciTech Connect

    Lotze, Stephan Versluis, Jan; Olijve, Luuk L. C.; Schijndel, Luuk van; Milroy, Lech G.; Voets, Ilja K.; Bakker, Huib J.

    2015-11-28

    We demonstrate that the enantiomers of chiral macromolecules at an aqueous interface can be distinguished with monolayer sensitivity using heterodyne-detected vibrational sum-frequency generation (VSFG). We perform VSFG spectroscopy with a polarization combination that selectively probes chiral molecular structures. By using frequencies far detuned from electronic resonances, we probe the chiral macromolecular structures with high surface specificity. The phase of the sum-frequency light generated by the chiral molecules is determined using heterodyne detection. With this approach, we can distinguish right-handed and left-handed helical peptides at a water-air interface. We thus show that heterodyne-detected VSFG is sensitive to the absolute configuration of complex, interfacial macromolecules and has the potential to determine the absolute configuration of enantiomers at interfaces.

  12. Correlations among experimental and theoretical NMR data to determine the absolute stereochemistry of darcyribeirine, a pentacyclic indole alkaloid isolated from Rauvolfia grandiflora

    NASA Astrophysics Data System (ADS)

    Cancelieri, Náuvia Maria; Ferreira, Thiago Resende; Vieira, Ivo José Curcino; Braz-Filho, Raimundo; Piló-Veloso, Dorila; Alcântara, Antônio Flávio de Carvalho

    2015-10-01

    Darcyribeirine (1) is a pentacyclic indole alkaloid isolated from Rauvolfia grandiflora. Stereochemistry of 1 was previously proposed based on 1D (coupling constant data) and 2D (NOESY correlations) NMR techniques, having been established a configuration 3R, 15S, and 20R (isomer 1a). Stereoisomers of 1 (i.e., 1a-1h) can be grouped into four sets of enantiomers. Carbon chemical shifts and hydrogen coupling constants were calculated using BLYP/6-31G* theory level for the eight isomers of 1. Calculated NMR data of 1a-1h were correlated with the corresponding experimental data of 1. The best correlations between theoretical and experimental carbon chemical shift data were obtained for the set of enantiomers 1e/1f to structures in the gaseous phase and considering solvent effects (using PCM and explicit models). Similar results were obtained when the same procedure was performed to correlations between theoretical and experimental coupling constant data. Finally, optical rotation calculations indicate 1e as its absolute stereochemistry. Orbital population analysis indicates that the hydrogen bonding between N-H of 1e and DMSO is due to contributions of its frontier unoccupied molecular orbitals, mainly LUMO+1, LUMO+2, and LUMO+3.

  13. Determination of absolute value of quantum efficiency of radiation in high quality GaN single crystals using an integrating sphere

    NASA Astrophysics Data System (ADS)

    Kojima, Kazunobu; Ohtomo, Tomomi; Ikemura, Ken-ichiro; Yamazaki, Yoshiki; Saito, Makoto; Ikeda, Hirotaka; Fujito, Kenji; Chichibu, Shigefusa F.

    2016-07-01

    Omnidirectional photoluminescence (ODPL) measurement using an integrating sphere was carried out to absolutely quantify the quantum efficiency of radiation ( η) in high quality GaN single crystals. The total numbers of photons belonging to photoluminescence (PL photons) and photons belonging to an excitation source (excitation photons) were simultaneously counted in the measurement, and η was defined as a ratio of the number of PL photons to the number of absorbed excitation photons. The ODPL spectra near the band edge commonly showed a two-peak structure, which originates from the sharp absorption edge of GaN. A methodology for quantifying internal quantum efficiency ( ηint ) from such experimentally obtained η is derived. A record high ηint of typically 15% is obtained for a freestanding GaN crystal grown by hydride vapor phase epitaxy on a GaN seed crystal synthesized by the ammonothermal method using an acidic mineralizer, when the excitation photon energy and power density were 3.81 eV and 60 W/cm2, respectively.

  14. Cosmic backgrounds of relic gravitons and their absolute normalization

    NASA Astrophysics Data System (ADS)

    Giovannini, Massimo

    2014-11-01

    Provided the consistency relations are not violated, the recent BICEP2 observations pin down the absolute normalization, the spectral slope and the maximal frequency of the cosmic graviton background produced during inflation. The properly normalized spectra are hereby computed from the lowest frequencies (of the order of the present Hubble rate) up to the highest frequency range in the GHz region. Deviations from the conventional paradigm cannot be excluded and are examined by allowing for different physical possibilities including, in particular, a running of the tensor spectral index, an explicit breaking of the consistency relations and a spike in the high-frequency tail of the spectrum coming either from a post-inflationary phase dominated by a stiff fluid or from the contribution of waterfall fields in a hybrid inflationary context. The direct determinations of the tensor to scalar ratio at low frequencies, if confirmed by the forthcoming observations, will also affect and constrain the high-frequency uncertainties. The limits on the cosmic graviton backgrounds coming from wide-band interferometers (such as LIGO/Virgo, LISA and BBO/DECIGO) together with a more accurate scrutiny of the tensor B-mode polarization at low frequencies will set direct bounds on the post-inflationary evolution and on other unconventional completions of the standard lore.

  15. The Genetic Architecture of Hearing Impairment in Mice: Evidence for Frequency-Specific Genetic Determinants

    PubMed Central

    Crow, Amanda L.; Ohmen, Jeffrey; Wang, Juemei; Lavinsky, Joel; Hartiala, Jaana; Li, Qingzhong; Li, Xin; Salehide, Pezhman; Eskin, Eleazar; Pan, Calvin; Lusis, Aldons J.; Allayee, Hooman; Friedman, Rick A.

    2015-01-01

    Genome-wide association studies (GWAS) have been successfully applied in humans for the study of many complex phenotypes. However, identification of the genetic determinants of hearing in adults has been hampered, in part, by the relative inability to control for environmental factors that might affect hearing throughout the lifetime, as well as a large degree of phenotypic heterogeneity. These and other factors have limited the number of large-scale studies performed in humans that have identified candidate genes that contribute to the etiology of this complex trait. To address these limitations, we performed a GWAS analysis using a set of inbred mouse strains from the Hybrid Mouse Diversity Panel. Among 99 strains characterized, we observed approximately two-fold to five-fold variation in hearing at six different frequencies, which are differentiated biologically from each other by the location in the cochlea where each frequency is registered. Among all frequencies tested, we identified a total of nine significant loci, several of which contained promising candidate genes for follow-up study. Taken together, our results indicate the existence of both genes that affect global cochlear function, as well as anatomical- and frequency-specific genes, and further demonstrate the complex nature of mammalian hearing variation. PMID:26342000

  16. The Genetic Architecture of Hearing Impairment in Mice: Evidence for Frequency-Specific Genetic Determinants.

    PubMed

    Crow, Amanda L; Ohmen, Jeffrey; Wang, Juemei; Lavinsky, Joel; Hartiala, Jaana; Li, Qingzhong; Li, Xin; Salehide, Pezhman; Eskin, Eleazar; Pan, Calvin; Lusis, Aldons J; Allayee, Hooman; Friedman, Rick A

    2015-11-01

    Genome-wide association studies (GWAS) have been successfully applied in humans for the study of many complex phenotypes. However, identification of the genetic determinants of hearing in adults has been hampered, in part, by the relative inability to control for environmental factors that might affect hearing throughout the lifetime, as well as a large degree of phenotypic heterogeneity. These and other factors have limited the number of large-scale studies performed in humans that have identified candidate genes that contribute to the etiology of this complex trait. To address these limitations, we performed a GWAS analysis using a set of inbred mouse strains from the Hybrid Mouse Diversity Panel. Among 99 strains characterized, we observed approximately two-fold to five-fold variation in hearing at six different frequencies, which are differentiated biologically from each other by the location in the cochlea where each frequency is registered. Among all frequencies tested, we identified a total of nine significant loci, several of which contained promising candidate genes for follow-up study. Taken together, our results indicate the existence of both genes that affect global cochlear function, as well as anatomical- and frequency-specific genes, and further demonstrate the complex nature of mammalian hearing variation. PMID:26342000

  17. A model for precalculus students to determine the resonance frequency of a trumpet mouthpiece

    NASA Astrophysics Data System (ADS)

    Chapman, Robert C.

    2001-05-01

    The trumpet mouthpiece as a Helmholtz resonator is used to show precalculus students a mathematical model for determining the approximate resonance frequency of the mouthpiece. The mathematics is limited to algebra and trigonometry. Using a system of mouthpieces that have interchangeable cups and backbores, students are introduced to the acoustics of this resonator. By gathering data on 51 different configurations of mouthpieces, the author modifies the existing Helmholtz resonator equation to account for both cup volumes and backbore configurations. Students then use this model for frequency predictions. Included are how to measure the different physical attributes of a trumpet mouthpiece at minimal cost. This includes methods for measuring cup volume, backbore volume, backbore length, throat area, etc. A portion of this phase is de-signed for students to become acquainted with some of the vocabulary of acoustics and the physics of sound.

  18. Application of several methods for determining transfer functions and frequency response of aircraft from flight data

    NASA Technical Reports Server (NTRS)

    Eggleston, John M; Mathews, Charles W

    1954-01-01

    In the process of analyzing the longitudinal frequency-response characteristics of aircraft, information on some of the methods of analysis has been obtained by the Langley Aeronautical Laboratory of the National Advisory Committee for Aeronautics. In the investigation of these methods, the practical applications and limitations were stressed. In general, the methods considered may be classed as: (1) analysis of sinusoidal response, (2) analysis of transient response as to harmonic content through determination of the Fourier integral by manual or machine methods, and (3) analysis of the transient through the use of least-squares solutions of the coefficients of an assumed equation for either the transient time response or frequency response (sometimes referred to as curve-fitting methods). (author)

  19. Target cell frequency is a genetically determined risk factor in radiation leukaemogenesis.

    PubMed

    Jawad, M; Giotopoulos, G; Cole, C; Plumb, M

    2007-09-01

    Whole body exposure to ionizing radiation increases the risk of radiation-induced acute myeloid leukaemia (r-AML). r-AML is the result of the accumulation of mutations in a single haemopoietic stem cell, so risk is therefore a function of the number of mutations required to transform the stem cell and the mutation rate. There is a genetic component to the risk of AML within the general population, and low penetrance variant alleles encoding DNA repair enzymes have been genetically implicated in therapy-related AML susceptibility. However, what is largely ignored is that target cell number, which defines the number of genomes at risk from DNA damaging agents, is also part of the equation that defines risk. We will review the evidence from genetic studies of inbred mouse models that target cell frequency is a risk factor in radiation leukaemogenesis. Inbred mouse strains that differ in their susceptibility to radiation-induced r-AML and thymic lymphoma (r-TL), spontaneous TL and pristane-induced plasmacytoma (PCT) have been exploited to identify susceptibility loci. The target cell in AML is the haemopoietic stem cell, whereas TLs and PCT arise from more mature lymphoid progenitor cells. Inbred mice also differ significantly in all aspects of haemopoiesis, and these differences have been used to identify quantitative trait loci (QTL) that determine the frequency of specific haemopoietic stem, progenitor or mature blood cells. The co-localization of QTL that determine risk and target cell frequency in all three haemopoietic malignancies is strong evidence that target cell frequency is a risk factor in radiation leukaemogenesis. PMID:17704327

  20. Determination of medium electrical properties through full-wave modelling of frequency domain reflectrometry data

    NASA Astrophysics Data System (ADS)

    André, Frédéric; Lambot, Sébastien

    2015-04-01

    Accurate knowledge of the shallow soil properties is of prime importance in agricultural, hydrological and environmental engineering. During the last decade, numerous geophysical techniques, either invasive or resorting to proximal or remote sensing, have been developed and applied for quantitative characterization of soil properties. Amongst them, time domain reflectrometry (TDR) and frequency domain reflectometry (FDR) are recognized as standard techniques for the determination of soil dielectric permittivity and electrical conductivity, based on the reflected electromagnetic waves from a probe inserted into the soil. TDR data were first commonly analyzed in the time domain using methods considering only a part of the waveform information. Later, advancements have led to the possibility of analyzing the TDR signal through full-wave inverse modeling either in the time or the frequency domains. A major advantage of FDR compared to TDR is the possibility to increase the bandwidth, thereby increasing the information content of the data and providing more detailed characterization of the medium. Amongst the recent works in this field, Minet et al. (2010) developed a modeling procedure for processing FDR data based on an exact solution of Maxwell's equations for wave propagation in one-dimensional multilayered media. In this approach, the probe head is decoupled from the medium and is fully described by characteristic transfer functions. The authors successfully validated the method for homogeneous sand subject to a range of water contents. In the present study, we further validated the modelling approach using reference liquids with well-characterized frequency-dependent electrical properties. In addition, the FDR model was coupled with a dielectric mixing model to investigate the ability of retrieving water content, pore water electrical conductivity and sand porosity from inversion of FDR data acquired in sand subject to different water content levels. Finally, the

  1. Determination of the optimum sampling frequency of noisy images by spatial statistics

    SciTech Connect

    Sanchez-Brea, Luis Miguel; Bernabeu, Eusebio

    2005-06-01

    In optical metrology the final experimental result is normally an image acquired with a CCD camera. Owing to the sampling at the image, an interpolation is usually required. For determining the error in the measured parameters with that image, knowledge of the uncertainty at the interpolation is essential. We analyze how kriging, an estimator used in spatial statistics, can generate convolution kernels for filtering noise in regularly sampled images. The convolution kernel obtained with kriging explicitly depends on the spatial correlation and also on metrological conditions, such as the random fluctuations of the measured quantity, and the resolution of the measuring devices. Kriging, in addition, allows us to determine the uncertainty of the interpolation, and we have analyzed it in terms of the sampling frequency and the random fluctuations of the image, comparing it with Nyquist criterion. By use of kriging, it is possible to determine the optimum-required sampling frequency for a noisy image so that the uncertainty at interpolation is below a threshold value.

  2. Frequency Synchronization Analysis in Digital lock-in Methods for Bio-impedance Determination

    NASA Astrophysics Data System (ADS)

    Brajkovič, Robert; Žagar, Tomaž; Križaj, Dejan

    2014-12-01

    The lock-in method is one of the most frequently used methods for reconstruction of measured signals and as such frequently applied in the (bio)impedance method to determine the modulus and phase of the (bio)impedance. In implementation of the method in a (bio)impedance measurement device one has to consider possible non synchronized frequencies of the reference and the analyzed signals as well as potential sources of noise. In this work we analyzed these errors theoretically and experimentally. We show that both amplitude and phase errors depend on the relative difference of the frequencies of the reference and investigated signal as well as the number of integration periods. Theoretically, these errors vanish during the determination of the (bio)impedance modulus and phase. In practical implementation the inaccuracies appear at points of very low determined signal amplitudes due to the limited accuracy of analog to digital converters and are distributed around these points due to other sources of noise inherent in implementation of the measurement device.

  3. Lipase-catalyzed resolution of (2R*,3S*)- and (2R*,3R*)-3-methyl-3-phenyl-2-aziridinemethanol at low temperatures and determination of the absolute configurations of the four stereoisomers.

    PubMed

    Sakai, Takashi; Liu, Yu; Ohta, Hiroshi; Korenaga, Toshinobu; Ema, Tadashi

    2005-02-18

    [reaction: see text] Lipase-catalyzed resolution of (2R*,3S*)-3-methyl-3-phenyl-2-aziridinemethanol, (+/-)-2, at low temperatures gave synthetically useful (2R,3S)-2 and its acetate (2S,3R)-2a with (2S)-selectivity (E = 55 at -40 degrees C), while a similar reaction of (2R*,3R*)-3-methyl-3-phenyl-2-aziridinemethanol, (+/-)-3, gave (2S,3S)-3 and its acetate (2R,3R)-3a with (2R)-selectivity (E = 73 at -20 degrees C). Compound (+/-)-2 was prepared conveniently via diastereoselective addition of MeMgBr to tert-butyl 3-phenyl-2H-azirine-2-carboxylate, (+/-)-1a, which was successfully prepared by the Neber reaction of oxime tosylate of tert-butyl benzoyl acetate 7a. The tert-butyl ester was requisite to promote this reaction. For determination of the absolute configuration of (2S,3R)-2a, enantiopure (2S,3R)-2 was independently prepared in three steps involving diastereoselective methylation of 3-phenyl-2H-azirine-2-methanol, (S)-10, with MeMgBr. The absolute configuration of (2S,3S)-3 was determined by X-ray analysis of the corresponding N-(S)-2-(6-methoxy-2-naphthyl)propanoyl derivative (S,S,S)-13. PMID:15704972

  4. Determination of ferroelectric contributions to electromechanical response by frequency dependent piezoresponse force microscopy.

    PubMed

    Seol, Daehee; Park, Seongjae; Varenyk, Olexandr V; Lee, Shinbuhm; Lee, Ho Nyung; Morozovska, Anna N; Kim, Yunseok

    2016-01-01

    Hysteresis loop analysis via piezoresponse force microscopy (PFM) is typically performed to probe the existence of ferroelectricity at the nanoscale. However, such an approach is rather complex in accurately determining the pure contribution of ferroelectricity to the PFM. Here, we suggest a facile method to discriminate the ferroelectric effect from the electromechanical (EM) response through the use of frequency dependent ac amplitude sweep with combination of hysteresis loops in PFM. Our combined study through experimental and theoretical approaches verifies that this method can be used as a new tool to differentiate the ferroelectric effect from the other factors that contribute to the EM response. PMID:27466086

  5. Determination of ferroelectric contributions to electromechanical response by frequency dependent piezoresponse force microscopy

    NASA Astrophysics Data System (ADS)

    Seol, Daehee; Park, Seongjae; Varenyk, Olexandr V.; Lee, Shinbuhm; Lee, Ho Nyung; Morozovska, Anna N.; Kim, Yunseok

    2016-07-01

    Hysteresis loop analysis via piezoresponse force microscopy (PFM) is typically performed to probe the existence of ferroelectricity at the nanoscale. However, such an approach is rather complex in accurately determining the pure contribution of ferroelectricity to the PFM. Here, we suggest a facile method to discriminate the ferroelectric effect from the electromechanical (EM) response through the use of frequency dependent ac amplitude sweep with combination of hysteresis loops in PFM. Our combined study through experimental and theoretical approaches verifies that this method can be used as a new tool to differentiate the ferroelectric effect from the other factors that contribute to the EM response.

  6. Experimental determination of frequency response function estimates for flexible joint industrial manipulators with serial kinematics

    NASA Astrophysics Data System (ADS)

    Saupe, Florian; Knoblach, Andreas

    2015-02-01

    Two different approaches for the determination of frequency response functions (FRFs) are used for the non-parametric closed loop identification of a flexible joint industrial manipulator with serial kinematics. The two applied experiment designs are based on low power multisine and high power chirp excitations. The main challenge is to eliminate disturbances of the FRF estimates caused by the numerous nonlinearities of the robot. For the experiment design based on chirp excitations, a simple iterative procedure is proposed which allows exploiting the good crest factor of chirp signals in a closed loop setup. An interesting synergy of the two approaches, beyond validation purposes, is pointed out.

  7. Determination of ferroelectric contributions to electromechanical response by frequency dependent piezoresponse force microscopy

    PubMed Central

    Seol, Daehee; Park, Seongjae; Varenyk, Olexandr V.; Lee, Shinbuhm; Lee, Ho Nyung; Morozovska, Anna N.; Kim, Yunseok

    2016-01-01

    Hysteresis loop analysis via piezoresponse force microscopy (PFM) is typically performed to probe the existence of ferroelectricity at the nanoscale. However, such an approach is rather complex in accurately determining the pure contribution of ferroelectricity to the PFM. Here, we suggest a facile method to discriminate the ferroelectric effect from the electromechanical (EM) response through the use of frequency dependent ac amplitude sweep with combination of hysteresis loops in PFM. Our combined study through experimental and theoretical approaches verifies that this method can be used as a new tool to differentiate the ferroelectric effect from the other factors that contribute to the EM response. PMID:27466086

  8. ABSOLUTE POLARIMETRY AT RHIC.

    SciTech Connect

    OKADA; BRAVAR, A.; BUNCE, G.; GILL, R.; HUANG, H.; MAKDISI, Y.; NASS, A.; WOOD, J.; ZELENSKI, Z.; ET AL.

    2007-09-10

    Precise and absolute beam polarization measurements are critical for the RHIC spin physics program. Because all experimental spin-dependent results are normalized by beam polarization, the normalization uncertainty contributes directly to final physics uncertainties. We aimed to perform the beam polarization measurement to an accuracy Of {Delta}P{sub beam}/P{sub beam} < 5%. The absolute polarimeter consists of Polarized Atomic Hydrogen Gas Jet Target and left-right pairs of silicon strip detectors and was installed in the RHIC-ring in 2004. This system features proton-proton elastic scattering in the Coulomb nuclear interference (CNI) region. Precise measurements of the analyzing power A{sub N} of this process has allowed us to achieve {Delta}P{sub beam}/P{sub beam} = 4.2% in 2005 for the first long spin-physics run. In this report, we describe the entire set up and performance of the system. The procedure of beam polarization measurement and analysis results from 2004-2005 are described. Physics topics of AN in the CNI region (four-momentum transfer squared 0.001 < -t < 0.032 (GeV/c){sup 2}) are also discussed. We point out the current issues and expected optimum accuracy in 2006 and the future.

  9. Using time-frequency analysis to determine time-resolved detonation velocity with microwave interferometry.

    PubMed

    Kittell, David E; Mares, Jesus O; Son, Steven F

    2015-04-01

    Two time-frequency analysis methods based on the short-time Fourier transform (STFT) and continuous wavelet transform (CWT) were used to determine time-resolved detonation velocities with microwave interferometry (MI). The results were directly compared to well-established analysis techniques consisting of a peak-picking routine as well as a phase unwrapping method (i.e., quadrature analysis). The comparison is conducted on experimental data consisting of transient detonation phenomena observed in triaminotrinitrobenzene and ammonium nitrate-urea explosives, representing high and low quality MI signals, respectively. Time-frequency analysis proved much more capable of extracting useful and highly resolved velocity information from low quality signals than the phase unwrapping and peak-picking methods. Additionally, control of the time-frequency methods is mainly constrained to a single parameter which allows for a highly unbiased analysis method to extract velocity information. In contrast, the phase unwrapping technique introduces user based variability while the peak-picking technique does not achieve a highly resolved velocity result. Both STFT and CWT methods are proposed as improved additions to the analysis methods applied to MI detonation experiments, and may be useful in similar applications. PMID:25933878

  10. Resonance frequencies and Young's modulus determination of magnetorheological elastomers using the photoacoustic technique

    NASA Astrophysics Data System (ADS)

    Daniel Macias, J.; Ordonez-Miranda, J.; Alvarado-Gil, J. J.

    2012-12-01

    A simple and reliable methodology for determining the Young's modulus of magnetorheological elastomers is proposed based on the resonance frequencies of the amplitude of the photoacoustic signal. An explicit expression for the pressure changes within a photoacoustic cell, due to the thermal expansion of the air and the elastic bending of a clamped circular elastic membrane, is derived and analyzed. It is found that the resonance behavior of the amplitude of the photoacoustic signal is due to the contribution of the axial bending of its thickness. It is also shown that the Young's modulus of the membrane is proportional to its density, the square of its resonance frequencies and the fourth power of its radius, and inversely proportional to the square of its thickness. The application of the proposed approach to membranes made up of spherical microparticles of carbonyl iron powder embedded in a matrix of silicone rubber with weight concentrations of 0%, 5.2%, and 13.7% yields accurate and reproducible results, which are in good agreement with reported data in the literature. The highest accuracy on the measurement of the resonance frequencies and therefore on the Young's modulus is found for the first resonance peak. When a magnetic field is applied to the samples to modify their stiffness, it is observed that the Young's modulus increases with the magnetic field. This novel application of the photoacoustic technique opens the possibility of performing mechanical characterization of a broad diversity of magnetorheological membranes.

  11. Determining the frequency of defensive medicine among general practitioners in Southeast Iran

    PubMed Central

    Moosazadeh, Mahmood; Movahednia, Mahtab; Movahednia, Nima; Amiresmaili, Mohammadreza; Aghaei, Iraj

    2014-01-01

    Background: Defensive medicine prompts physicians not to admit high-risk patients who need intensive care. This phenomenon not only decreases the quality of healthcare services, but also wastes scarce health resources. Defensive medicine occurs in negative and positive forms. Hence, the present study aimed to determine frequency of positive and negative defensive medicine behaviors and their underlying factors among general practitioners in Southeast Iran. Methods: The present cross-sectional study was performed among general practitioners in Southeast Iran. 423 subjects participated in the study on a census basis and a questionnaire was used for data collection. Data analysis was carried out using descriptive and analytical statistics through SPSS 20. Results: The majority of participants were male (58.2%). The mean age of physicians was 40 ± 8.5. The frequency of positive and negative defensive medicine among general practitioners in Southeast Iran was 99.8% and 79.2% respectively. A significant relationship was observed between working experience, being informed of law suits against their colleagues, and committing defensive medicine behavior (P< 0.001). Conclusion: The present study indicated high frequency of defensive medicine behavior in the Southeast Iran. So, it calls policy-makers special attention to improve the status quo. PMID:24757688

  12. The results of determining the gravity potential difference on the measurement of the relativistic frequency shift of the mobile frequency standard

    NASA Astrophysics Data System (ADS)

    Gienko, Elena; Kanushin, Vadim; Tolstikov, Alexander; Karpik, Alexander; Kosarev, Nikolay; Ganagina, Irina

    2016-04-01

    In 2015 in the research on the grant of the Russian science Foundation No. 14-27-00068 was experimentally confirmed the possibility of measuring the gravity potential difference on relativistic frequency shift of the mobile hydrogen standard CH1-1006 (relative frequency instability of the order 10E-14). Hydrogen frequency standard CH1-1006 was calibrated in the system of secondary standard WET 1-19 (SNIIM, Novosibirsk, Russia) and transported to the place of experiment (a distance of 550 km, the Russian Federation, Republic of Altai), where it moved between the measured points at a distance of 35 km with a height difference of 850 meters. To synchronize spatially separated standard CH1-1006 and secondary standard WET 1-19 was applied the method "CommonView", based on the processing results of pseudorange phase GNSS measurements at the point of placement hours. Changing the frequency standard CH1-1006, measured in the system of secondary standard WET 1-19 and associated with his movement between points and the change of gravitational potential, was equal to 7.98•10E-14. Evaluation of root-mean-square two-sample frequency deviation of the standard at the time interval of the experiment was equal to the value of 7.27•10E-15. To control the results of the frequency determination of the gravity potential difference between the points were made high precision gravimetric measurements with an error of 6 MkGal and GNSS measurements for the coordinate determinations in ITRF2008 with an accuracy of 2-5 cm. The difference between the results of the frequency determination of the gravity potential difference with control data from GNSS and gravimetric measurements was estimated 16% of the total value that corresponds to the error of frequency measurement in the experiment. The possibility of using a single moveable frequency standard to determine the gravity potential difference at spaced points using the method of "CommonView", without the use of optical communications

  13. The Use of Additional GPS Frequencies to Independently Determine Tropospheric Water Vapor Profiles

    NASA Technical Reports Server (NTRS)

    Herman, B.M.; Feng, D.; Flittner, D. E.; Kursinski, E. R.

    2000-01-01

    It is well known that the currently employed L1 and L2 GPS/MET frequencies (1.2 - 1.6) Ghz) do not allow for the separation of water vapor and density (or temperature) from active microwave occultation measurements in regions of the troposphere warmer than 240 K Therefore, additional information must be used, from other types of measurements and weather analyses, to recover water vapor (and temperature) profiles. Thus in data sparse regions, these inferred profiles can be subject to larger errors than would result in data rich regions. The use of properly selected additional GPS frequencies enables a direct, independent measurement of the absorption associated with the water vapor profile, which may then be used in the standard GPS/MET retrievals to obtain a more accurate determination of atmospheric temperature throughout the water vapor layer. This study looks at the use of microwave crosslinks in the region of the 22 Ghz water vapor absorption line for this purpose. An added advantage of using 22 Ghz frequencies is that they are only negligibly affected by the ionosphere in contrast to the large effect at the GPS frequencies. The retrieval algorithm uses both amplitude and phase measurements to obtain profiles of atmospheric pressure, temperature and water water vapor pressure with a vertical resolution of 1 km or better. This technique also provides the cloud liquid water content along the ray path, which is in itself an important element in climate monitoring. Advantages of this method include the ability to make measurements in the presence of clouds and the use of techniques and technology proven through the GPS/MET experiment and several of NASA's planetary exploration missions. Simulations demonstrating this method will be presented for both clear and cloudy sky conditions.

  14. Endocardial endothelium is a key determinant of force-frequency relationship in rat ventricular myocardium

    PubMed Central

    Shen, Xiaoxu; Tan, Zhen; Zhong, Xin; Tian, Ye; Wang, Xian; Yu, Bo; Ramirez-Correa, Genaro; Murphy, Anne; Gabrielson, Kathleen; Paolocci, Nazareno

    2013-01-01

    We tested the hypothesis that removing endocardial endothelium (EE) negatively impacts the force-frequency relationship (FFR) of ventricular myocardium and dissected the signaling that underlies this phenomenon. EE of rat trabeculae was selectively damaged by brief (<1 s) exposure to 0.1% Triton X-100. Force, intracellular Ca2+ transient (iCa2+), and activity of protein kinase A (PKA) and protein kinase C (PKC) were determined. In control muscles, force and iCa2+ increased as the stimulation frequency increased in steps of 0.5 Hz up to 3.0 Hz. However, EE-denuded (EED) muscles exhibited a markedly blunted FFR. Neither isoproterenol (ISO; 0.1–5 nmol/l) nor endothelin-1 (ET-1; 10–100 nmol/l) alone restored the slope of FFR in EED muscles. Intriguingly, however, a positive FFR was restored in EED preparations by combining low concentrations of ISO (0.1 nmol/l) and ET-1 (20 nmol/l). In intact muscles, PKA and PKC activity increased proportionally with the increase in frequency. This effect was completely lost in EED muscles. Again, combining ISO and ET-1 fully restored the frequency-dependent rise in PKA and PKC activity in EED muscles. In conclusion, selective damage of EE leads to significantly blunted FFR. A combination of low concentrations of ISO and ET-1 successfully restores FFR in EED muscles. The interdependence of ISO and ET-1 in this process indicates cross-talk between the β1-PKA and ET-1-PKC pathways for a normal (positive) FFR. The results also imply that dysfunction of EE and/or EE-myocyte coupling may contribute to flat (or even negative) FFR in heart failure. PMID:23703113

  15. Ethylmethanesulfonate saturation mutagenesis in Arabidopsis to determine frequency of herbicide resistance.

    PubMed

    Jander, Georg; Baerson, Scott R; Hudak, Jebecka A; Gonzalez, Kathleen A; Gruys, Kenneth J; Last, Robert L

    2003-01-01

    Plant resistance to glyphosate has been reported far less frequently than resistance to sulfonylurea and imidazolinone herbicides. However, these studies tend to be anecdotal, without side by side comparisons for a single species or natural isolate. In this study, we tested the frequencies of resistance of three herbicides in a controlled ethylmethanesulfonate (EMS) saturation mutagenesis experiment, allowing a direct comparison of the frequencies at which resistant mutant plants arise. The 100% growth inhibition dose rates of glyphosate, chlorsulfuron (a sulfonylurea herbicide), and imazethapyr (an imidazolinone herbicide) were determined for Arabidopsis. Populations of EMS-mutagenized M(2) seedlings were sprayed with twice the 100% growth inhibition dose of glyphosate, chlorsulfuron, or imazethapyr, and herbicide-resistant mutants were identified. Although there were no glyphosate-resistant mutants among M(2) progeny of 125,000 Columbia and 125,000 Landsberg erecta M(1) lines, chlorsulfuron resistance and imazethapyr resistance each appeared at frequencies of 3.2 x 10(-5). Given the observed frequency of herbicide resistance mutations, we calculate that there are at least 700 mutations in each EMS-mutagenized Arabidopsis line and that fewer than 50,000 M(1) lines are needed to have a 95% chance of finding a mutation in any given G:C base pair in the genome. As part of this study, two previously unreported Arabidopsis mutations conferring resistance to imidazolinone herbicides, csr1-5 (Ala-122-Thr) and csr1-6 (Ala-205-Val), were discovered. Neither of these mutations caused enhanced resistance to chlorsulfuron in Arabidopsis. PMID:12529522

  16. Real-time single-frequency GPS/MEMS-IMU attitude determination of lightweight UAVs.

    PubMed

    Eling, Christian; Klingbeil, Lasse; Kuhlmann, Heiner

    2015-01-01

    In this paper, a newly-developed direct georeferencing system for the guidance, navigation and control of lightweight unmanned aerial vehicles (UAVs), having a weight limit of 5 kg and a size limit of 1.5 m, and for UAV-based surveying and remote sensing applications is presented. The system is intended to provide highly accurate positions and attitudes (better than 5 cm and 0.5°) in real time, using lightweight components. The main focus of this paper is on the attitude determination with the system. This attitude determination is based on an onboard single-frequency GPS baseline, MEMS (micro-electro-mechanical systems) inertial sensor readings, magnetic field observations and a 3D position measurement. All of this information is integrated in a sixteen-state error space Kalman filter. Special attention in the algorithm development is paid to the carrier phase ambiguity resolution of the single-frequency GPS baseline observations. We aim at a reliable and instantaneous ambiguity resolution, since the system is used in urban areas, where frequent losses of the GPS signal lock occur and the GPS measurement conditions are challenging. Flight tests and a comparison to a navigation-grade inertial navigation system illustrate the performance of the developed system in dynamic situations. Evaluations show that the accuracies of the system are 0.05° for the roll and the pitch angle and 0.2° for the yaw angle. The ambiguities of the single-frequency GPS baseline can be resolved instantaneously in more than 90% of the cases. PMID:26501281

  17. Real-Time Single-Frequency GPS/MEMS-IMU Attitude Determination of Lightweight UAVs

    PubMed Central

    Eling, Christian; Klingbeil, Lasse; Kuhlmann, Heiner

    2015-01-01

    In this paper, a newly-developed direct georeferencing system for the guidance, navigation and control of lightweight unmanned aerial vehicles (UAVs), having a weight limit of 5 kg and a size limit of 1.5 m, and for UAV-based surveying and remote sensing applications is presented. The system is intended to provide highly accurate positions and attitudes (better than 5 cm and 0.5∘) in real time, using lightweight components. The main focus of this paper is on the attitude determination with the system. This attitude determination is based on an onboard single-frequency GPS baseline, MEMS (micro-electro-mechanical systems) inertial sensor readings, magnetic field observations and a 3D position measurement. All of this information is integrated in a sixteen-state error space Kalman filter. Special attention in the algorithm development is paid to the carrier phase ambiguity resolution of the single-frequency GPS baseline observations. We aim at a reliable and instantaneous ambiguity resolution, since the system is used in urban areas, where frequent losses of the GPS signal lock occur and the GPS measurement conditions are challenging. Flight tests and a comparison to a navigation-grade inertial navigation system illustrate the performance of the developed system in dynamic situations. Evaluations show that the accuracies of the system are 0.05∘ for the roll and the pitch angle and 0.2∘ for the yaw angle. The ambiguities of the single-frequency GPS baseline can be resolved instantaneously in more than 90% of the cases. PMID:26501281

  18. Implants as absolute anchorage.

    PubMed

    Rungcharassaeng, Kitichai; Kan, Joseph Y K; Caruso, Joseph M

    2005-11-01

    Anchorage control is essential for successful orthodontic treatment. Each tooth has its own anchorage potential as well as propensity to move when force is applied. When teeth are used as anchorage, the untoward movements of the anchoring units may result in the prolonged treatment time, and unpredictable or less-than-ideal outcome. To maximize tooth-related anchorage, techniques such as differential torque, placing roots into the cortex of the bone, the use of various intraoral devices and/or extraoral appliances have been implemented. Implants, as they are in direct contact with bone, do not possess a periodontal ligament. As a result, they do not move when orthodontic/orthopedic force is applied, and therefore can be used as "absolute anchorage." This article describes different types of implants that have been used as orthodontic anchorage. Their clinical applications and limitations are also discussed. PMID:16463910

  19. Absolute Equilibrium Entropy

    NASA Technical Reports Server (NTRS)

    Shebalin, John V.

    1997-01-01

    The entropy associated with absolute equilibrium ensemble theories of ideal, homogeneous, fluid and magneto-fluid turbulence is discussed and the three-dimensional fluid case is examined in detail. A sigma-function is defined, whose minimum value with respect to global parameters is the entropy. A comparison is made between the use of global functions sigma and phase functions H (associated with the development of various H-theorems of ideal turbulence). It is shown that the two approaches are complimentary though conceptually different: H-theorems show that an isolated system tends to equilibrium while sigma-functions allow the demonstration that entropy never decreases when two previously isolated systems are combined. This provides a more complete picture of entropy in the statistical mechanics of ideal fluids.

  20. Absolute determination of charge-coupled device quantum detection efficiency using Si K-edge x-ray absorption fine structure

    SciTech Connect

    Dunn, J; Steel, A B

    2012-05-06

    We report a method to determine the quantum detection efficiency and the absorbing layers on a front-illuminated charge-coupled device (CCD). The CCD under study, as part of a crystal spectrometer, measures intense continuum x-ray emission from a picosecond laser-produced plasma and spectrally resolves the Si K-edge x-ray absorption fine structure features due to the electrode gate structure of the device. The CCD response across the Si K-edge shows a large discontinuity as well as a number of oscillations that are identified individually and uniquely from Si, SiO{sub 2}, and Si{sub 3}N{sub 4} layers. From the spectral analysis of the structure and K-edge discontinuity, the active layer thickness and the different absorbing layers thickness can be determined precisely. A precise CCD detection model from 0.2-10 keV can be deduced from this highly sensitive technique.

  1. Absolute isotopic abundances of TI in meteorites

    NASA Astrophysics Data System (ADS)

    Niederer, F. R.; Papanastassiou, D. A.; Wasserburg, G. J.

    1985-03-01

    The absolute isotope abundance of Ti has been determined in Ca-Al-rich inclusions from the Allende and Leoville meteorites and in samples of whole meteorites. The absolute Ti isotope abundances differ by a significant mass dependent isotope fractionation transformation from the previously reported abundances, which were normalized for fractionation using 46Ti/48Ti. Therefore, the absolute compositions define distinct nucleosynthetic components from those previously identified or reflect the existence of significant mass dependent isotope fractionation in nature. The authors provide a general formalism for determining the possible isotope compositions of the exotic Ti from the measured composition, for different values of isotope fractionation in nature and for different mixing ratios of the exotic and normal components.

  2. New directional results and determination of absolute archaeointensity using both the classical Thellier and the multi-specimen procedures for two kilns excavated at Osterietta, Italy

    NASA Astrophysics Data System (ADS)

    Tema, Evdokia; Camps, Pierre; Ferrara, Enzo

    2014-05-01

    A detailed rock-magnetic and archaeomagnetic study has been carried out on two rescue excavation kilns discovered during the works to expand a highway at the location of Osterietta, in Northen Italy. Systematic archaeomagnetic sampling was carried out collecting 15 samples from the first kiln (OSA) and 8 samples from the second kiln (OSB), all of them oriented in situ with a magnetic compass and an inclinometer. Magnetic mineralogy measurements have been carried out in order to determine the main magnetic carrier of the samples and to check their thermal stability. Standard thermal demagnetization procedures have been used to determine the archaeomagnetic direction registered by the bricks during their last firing. Demagnetization results show a very stable characteristic remanent magnetization (ChRM). We averaged the directions for each kiln separately and calculated the statistical parameters assuming a Fisherian distribution. The archaeointensity of both kilns has also been recovered with both the classical Thellier-Thellier method and the multi-specimen procedure (MSP-DSC). During the Thellier experiments, regular partial thermoremanent magnetization checks have been performed and the effect of the anisotropy of the thermoremanent magnetization (TRM) and cooling rate upon TRM intensity acquisition have been investigated in all samples. The multi-specimen procedure was performed with a very fast-heating oven developed at Montpellier (France). The intensity results obtained from both methods have been compared and the full geomagnetic field vector determined for each kiln has been used for archaeomagnetic dating. The obtained results show that the kilns were almost contemporaneous and their last use occurred in the 1750-1850 AD time interval.

  3. How Often Do Early Childhood Teachers Teach Science Concepts? Determinants of the Frequency of Science Teaching in Kindergarten

    ERIC Educational Resources Information Center

    Saçkes, Mesut

    2014-01-01

    The purpose of the present study was to explore how often teachers of young children teach science concepts in kindergarten and examine the factors that influence the frequency of science teaching in early years. A theoretical model of the determinants of the frequency of science teaching in kindergarten was developed and tested using a…

  4. A Tale of Two Frequencies: Determining the Speed of Lexical Access for Mandarin Chinese and English Compounds

    ERIC Educational Resources Information Center

    Janssen, Niels; Bi, Yanchao; Caramazza, Alfonso

    2008-01-01

    Two picture naming experiments show that compound word production in Mandarin Chinese and in English is determined by the compound's whole-word frequency, and not by its constituent morpheme frequency. Four control experiments rule out that these results are caused by recognition or articulatory processes. These results are consistent with models…

  5. Seismology of Procyon A: determination of mode frequencies, amplitudes, lifetimes, and granulation noise

    NASA Astrophysics Data System (ADS)

    Leccia, S.; Kjeldsen, H.; Bonanno, A.; Claudi, R. U.; Ventura, R.; Paternò, L.

    2007-03-01

    The F5 IV-V star Procyon A (α-CMi) was observed in January 2001 by means of the high-resolution spectrograph SARG operating with the TNG 3.5 m Italian telescope (Telescopio Nazionale Galileo) in the Canary Islands, exploiting the iodine cell technique. The time series of about 950 spectra carried out during 6 observation nights and a preliminary data analysis [CITE] showed a significant power excess between 0.5 and 1.5 mHz, with ≃1 m s-1 peak amplitude. Here we present a more detailed analysis of the time series, based on both radial velocity and line equivalent width analyses. From the power spectrum we found a typical p-mode frequency comb-like structure, identified 11 frequencies with a good margin of certainty in the interval 500-1400 μ Hz of modes with l=0,1,2 and 7≤ n ≤ 22, and determined large and small frequency separations, Δν = 55.90± 0.08 μ{Hz} and δν02=7.1± 1.3 μ Hz, respectively. The mean amplitude per mode (l=0,1) at peak power is 0.45± 0.07 m s-1, twice larger than the solar one, and the mode lifetime is 2± 0.4 d, which indicates a non-coherent, stochastic source of mode excitation. Line equivalent width measurements do not show a significant excess in power in the examined spectral region but allowed us to infer an upper limit to the granulation noise.

  6. Significantly Improving Regional Seismic Amplitude Tomography at Higher Frequencies by Determining S -Wave Bandwidth

    DOE PAGESBeta

    Fisk, Mark D.; Pasyanos, Michael E.

    2016-05-03

    Characterizing regional seismic signals continues to be a difficult problem due to their variability. Calibration of these signals is very important to many aspects of monitoring underground nuclear explosions, including detecting seismic signals, discriminating explosions from earthquakes, and reliably estimating magnitude and yield. Amplitude tomography, which simultaneously inverts for source, propagation, and site effects, is a leading method of calibrating these signals. A major issue in amplitude tomography is the data quality of the input amplitude measurements. Pre-event and prephase signal-to-noise ratio (SNR) tests are typically used but can frequently include bad signals and exclude good signals. The deficiencies ofmore » SNR criteria, which are demonstrated here, lead to large calibration errors. To ameliorate these issues, we introduce a semi-automated approach to assess the bandwidth of a spectrum where it behaves physically. We determine the maximum frequency (denoted as Fmax) where it deviates from this behavior due to inflections at which noise or spurious signals start to bias the spectra away from the expected decay. We compare two amplitude tomography runs using the SNR and new Fmax criteria and show significant improvements to the stability and accuracy of the tomography output for frequency bands higher than 2 Hz by using our assessments of valid S-wave bandwidth. We compare Q estimates, P/S residuals, and some detailed results to explain the improvements. Lastly, for frequency bands higher than 4 Hz, needed for effective P/S discrimination of explosions from earthquakes, the new bandwidth criteria sufficiently fix the instabilities and errors so that the residuals and calibration terms are useful for application.« less

  7. Atomic frequency standards at NICT

    NASA Astrophysics Data System (ADS)

    Ido, T.; Fujieda, M.; Hachisu, H.; Hayasaka, K.; Kajita, M.; Kojima, R.; Kumagai, M.; Locke, C.; Li, Y.; Matsubara, K.; Nogami, A.; Shiga, N.; Yamaguchi, A.; Koyama, Y.; Hosokawa, M.; Hanado, Y.

    2011-10-01

    Various activities of atomic frequency standards studied in National Institute of Information and Communications Technology (NICT) are briefly reviewed. After BIPM accepted the first cesium fountain clock in NICT as a reference to determine International Atomic Time (TAI), efforts to further reduce the uncertainty of collision shifts are ongoing. A second fountain clock using atomic molasses is being built to enable the operation with less atomic density. Single ion clock using calcium has been pursued for several years in NICT. The absolute frequency measured in 2008 has CIPM to adopt the Ca+ clock transition as a part of the list of radiation (LoR) to realize the meter. Sr lattice clock has started its operation last year. The absolute frequency agreed well with those obtained in other institutes. Study of stable cavities to stabilize clock lasers are also introduced.

  8. The equilibrium constant for N2O5 = NO2 + NO3 - Absolute determination by direct measurement from 243 to 397 K

    NASA Technical Reports Server (NTRS)

    Cantrell, C. A.; Davidson, J. A.; Mcdaniel, A. H.; Shetter, R. E.; Calvert, J. G.

    1988-01-01

    Direct determinations of the equilibrium constant for the reaction N2O5 = NO2 + NO3 were carried out by measuring NO2, NO3, and N2O5 using long-path visible and infrared absorption spectroscopy as a function of temperature from 243 to 397 K. The first-order decay rate constant of N2O5 was experimentally measured as a function of temperature. These results are in turn used to derive a value for the rate coefficient for the NO-forming channel in the reaction of NO3 with NO2. The implications of the results for atmospheric chemistry, the thermodynamics of NO3, and for laboratory kinetics studies are discussed.

  9. A test of the role of electrostatic interactions in determining the CO stretch frequency in carbonmonoxymyoglobin.

    PubMed

    Decatur, S M; Boxer, S G

    1995-07-01

    The vibrational frequency of CO bound to myoglobin can be varied by up to 60 cm-1 by making site-specific mutations in the distal pocket. These changes may result from specific chemical interactions between distal amino acids and the CO or from changes in the electrostatic field of the distal pocket. In this paper, we separate the relative contributions of these two effects by comparing the IR spectra of the carbonmonoxy complexes of human myoglobin mutants V68N, V68D, and V68E. The effect of replacing valine with these polar amino acids on the electrostatic environment of the distal heme pocket has been independently determined earlier by measurements of the heme reduction potential and electronic absorption spectral band shifts. While all three mutations result in a negative dipole pointing towards the CO ligand, the CO stretch frequency shifts differently in each case. These differences are attributed to specific chemical interactions between the amino acids and the CO ligand. PMID:7612000

  10. Theoretical determination of parity-violating vibrational frequency differences between the enantiomers of chiral molecules.

    PubMed

    Viglione, Rosario G

    2004-11-22

    A perturbation treatment has been used to compute the leading first- and second-order parity-violating corrections to the vibrational energy levels of a chiral molecule. Assuming the molecular equilibrium geometry as expansion point of both parity-violating and parity-conserving potential-energy surfaces, it is shown that these corrections, i.e., harmonic and anharmonic contributions, are of the same order of magnitude and that none of them can be neglected for a realistic determination of vibrational frequency differences. Numerical tests based on ab initio MP2 force fields and quantum-relativistic calculations of the parity-violating potential for each normal mode of PHBrF and AsHBrF molecules confirm this conclusion. In particular, it is shown that a normal mode of AsHBrF is characterized by one of the largest vibrational frequency difference ever found--the prediction is approximately 0.1 Hz--only one order of magnitude less than the presumed resolution limit of current experimental investigations. PMID:15549870

  11. Determination of delayed neutrons source in the frequency domain based on in-pile oscillation measurements

    SciTech Connect

    Yedvab, Y.; Reiss, I.; Bettan, M.; Harari, R.; Grober, A.; Ettedgui, H.; Caspi, E. N.

    2006-07-01

    A method for determining delayed neutrons source in the frequency domain based on measuring power oscillations in a non-critical reactor is presented. This method is unique in the sense that the delayed neutrons source is derived from the dynamic behavior of the reactor, which serves as the measurement system. An algorithm for analyzing power oscillation measurements was formulated, which avoids the need for a multi-parameter non-linear fit process used by other methods. Using this algorithm results of two sets of measurements performed in IRR-I and IRR-II (Israeli Research Reactors I and II) are presented. The agreement between measured values from both reactors and calculated values based on Keepin (and JENDL-3.3) group parameters is very good. (authors)

  12. Automatic determination of nose frequency and time of initiating sferic of whistlers

    NASA Astrophysics Data System (ADS)

    Lichtenberger, János; Clilverd, Mark; Rodger, C. J.; Collier, Andrew; Ferencz, Csaba; Hamar, D.; Steinbach, P.

    2012-07-01

    Both the traditional, human assisted methods, and the recently developed automatic whistler inversion method [1,2] need at least an estimate for the time of the initial sferic (t0) and also the nose frequency (fn) for the whistler inversion to work. Failure to provide accurate values for these data will lead to no or useless derivation of whistler propagation paths and equatorial electron densities, which are the key parameters for modelling the plasmasphere and wave-particle interactions in Space Weather studies. In this presentation we will discuss a new automatic method to determine t0 and fn which is based on the combination of a well known method [3] and the new method developed for the implementation of the automatic whistler analyzer [2]. While this approach will be useful for traditional whistler inversions providing faster and more accurate results, the real power of the method can be fully utilized in the automatic whistler analyzer, where the accurate values of t0 and the fn for individual traces of a multiple-path whistler group dramatically reduce the time of inversion by avoiding a time-consuming search. The paper presents the details of the algorithm as well as case studies on its application. References 1. Dowden, R.L and Allcock, G. McK (1971): Determination of nose frequency of non-nose whistlers, J. Atmos. Terr. Phys., 33, pp1125-1129. 2. Lichtenberger, J. (2009), A new whistler inversion method, J. Geophys. Res., 114, A07222, doi:10.1029/2008JA013799. 3. Lichtenberger, J., C. Ferencz, D. Hamar, P. Steinbach, C. J. Rodger, M. A. Clilverd, and A. B. Collier (2010), Automatic Whistler Detector and Analyzer system: Implementation of the analyzer algorithm, J. Geophys. Res., 115, A12214, doi:10.1029/2010JA015931.

  13. Absolute molecular weight determination of hypromellose acetate succinate by size exclusion chromatography: use of a multi angle laser light scattering detector and a mixed solvent.

    PubMed

    Chen, Raymond; Ilasi, Nicholas; Sekulic, Sonja S

    2011-12-01

    Molecular weight distribution is an important quality attribute for hypromellose acetate succinate (HPMCAS), a pharmaceutical excipient used in spray-dried dispersions. Our previous study showed that neither relative nor universal calibration method of size exclusion chromatography (SEC) works for HPMCAS polymers. We here report our effort to develop a SEC method using a mass sensitive multi angle laser light scattering detector (MALLS) to determine molecular weight distributions of HPMCAS polymers. A solvent screen study reveals that a mixed solvent (60:40%, v/v 50mM NaH(2)PO(4) with 0.1M NaNO(3) buffer: acetonitrile, pH* 8.0) is the best for HPMCAS-LF and MF sub-classes. Use of a mixed solvent creates a challenging condition for the method that uses refractive index detector. Therefore, we thoroughly evaluated the method performance and robustness. The mean weight average molecular weight of a polyethylene oxide standard has a 95% confidence interval of (28,443-28,793) g/mol vs. 28,700g/mol from the Certificate of Analysis. The relative standard deviations of average molecular weights for all polymers are 3-6%. These results and the Design of Experiments study demonstrate that the method is accurate and robust. PMID:21840663

  14. Performance improvement of GPS single frequency, single epoch attitude determination with poor satellite visibility

    NASA Astrophysics Data System (ADS)

    Chen, Wantong; Sun, Xingli

    2016-07-01

    Similar to global positioning system (GPS) positioning in urban canyons, a fast and successful attitude determination with limited satellite visibility is very significant. For land vehicles, the possible attitude candidates can be treated as a spherical zone with the center at the reference antenna and the baseline as the radius. This provides an important constraint, which can be exploited to improve the reliability of GPS single frequency and single epoch attitude determination in the case of poor satellite reception. First, we fully integrate the spherical zone constraint into the estimation procedure of ambiguity resolution, but not in the validation procedure. Combining both the coordinate domain search and the ambiguity domain search, allows development of a global minimizer of the fixed ambiguity objective function. This scheme also improves the precision of the float ambiguity solution, thus avoiding the problem of search halting. The performance of the new ambiguity resolution method was analyzed by means of several experimental tests, using simulated as well as actual GPS data in urban environments. The experimental results showed that this new, proposed method can utilize a priori spherical zone knowledge to improve the reliability of ambiguity resolution in difficult environments.

  15. Precise Orbit Determination of LEO Satellite Using Dual-Frequency GPS Data

    NASA Astrophysics Data System (ADS)

    Hwang, Yoola; Lee, Byoung-Sun; Kim, Jaehoon; Yoon, Jae-Cheol

    2009-06-01

    KOrea Multi-purpose SATellite (KOMPSAT)-5 will be launched at 550km altitude in 2010. Accurate satellite position (20 cm) and velocity (0.03 cm/s) are required to treat highly precise Synthetic Aperture Radar (SAR) image processing. Ionosphere delay was eliminated using dual frequency GPS data and double differenced GPS measurement removed common clock errors of both GPS satellites and receiver. SAC-C carrier phase data with 0.1 Hz sampling rate was used to achieve precise orbit determination (POD) with ETRI GNSS Precise Orbit Determination (EGPOD) software, which was developed by ETRI. Dynamic model approach was used and satellite's position, velocity, and the coefficients of solar radiation pressure and drag were adjusted once per arc using Batch Least Square Estimator (BLSE) filter. Empirical accelerations for sinusoidal radial, along-track, and cross track terms were also estimated once per revolution for unmodeled dynamics. Additionally piece-wise constant acceleration for cross-track direction was estimated once per arc. The performance of POD was validated by comparing with JPL's Precise Orbit Ephemeris (POE).

  16. Absolute Identification by Relative Judgment

    ERIC Educational Resources Information Center

    Stewart, Neil; Brown, Gordon D. A.; Chater, Nick

    2005-01-01

    In unidimensional absolute identification tasks, participants identify stimuli that vary along a single dimension. Performance is surprisingly poor compared with discrimination of the same stimuli. Existing models assume that identification is achieved using long-term representations of absolute magnitudes. The authors propose an alternative…

  17. Be Resolute about Absolute Value

    ERIC Educational Resources Information Center

    Kidd, Margaret L.

    2007-01-01

    This article explores how conceptualization of absolute value can start long before it is introduced. The manner in which absolute value is introduced to students in middle school has far-reaching consequences for their future mathematical understanding. It begins to lay the foundation for students' understanding of algebra, which can change…

  18. Determining Absolute Zero Using a Tuning Fork

    ERIC Educational Resources Information Center

    Goldader, Jeffrey D.

    2008-01-01

    The Celsius and Kelvin temperature scales, we tell our students, are related. We explain that a change in temperature of 1 degree C corresponds to a change of 1 Kelvin and that atoms and molecules have zero kinetic energy at zero Kelvin, -273 degrees C. In this paper, we will show how students can derive the relationship between the Celsius and…

  19. Determining Absolute Zero in the Kitchen Sink.

    ERIC Educational Resources Information Center

    Otani, Robert; Siegel, Peter

    1991-01-01

    Presents an experiment to demonstrate Charles's Law of Ideal Gases by creating a constant-pressure thermometer from materials that can be found in the kitchen. Discusses the underlying mathematical relationships and a step-by-step description of the experiment. (MDH)

  20. Surveying with the A10-20 Absolute Gravimeter for Geodesy and Geodynamics - first results

    NASA Astrophysics Data System (ADS)

    Krynski, Jan; Sekowski, Marcin

    2010-05-01

    The A10 is the first outdoor absolute gravimeter that allows for the determination of gravity with high precision. Absolute gravity survey with the A10 becomes highly competitive in terms of both efficiency and precision with traditional relative gravity survey. The portable A10-20 absolute gravimeter has been installed at the Borowa Gora Geodetic-Geophysical Observatory in September 2008. Since then a number of test measurements was conducted. Under laboratory conditions the series of gravity determination was obtained at two independent pillars at Borowa Gora as well as in Metsahovi and the BIPM gravimetric laboratories. Also a number outdoor gravity measurements with the use of mobile gravimetric laboratory was performed at the stations of gravity control in Poland and in Finland. The results obtained indicate high quality of gravity determination with the A10 under laboratory conditions and unprecedented quality under field conditions. They confirm the applicability of the A10 absolute gravimeter to the modernization of gravity control and high precision gravity survey required in modern gravity networks, but also its usefulness in microgravimetry as well as geodynamics. Some practical problems concerning the use of the A10 and its operational procedure including laser and frequency standard are discussed.

  1. Establishment of a real-time RT-PCR for the determination of absolute amounts of IGF-I and IGF-II gene expression in liver and extrahepatic sites of the tilapia.

    PubMed

    Caelers, Antje; Berishvili, Giorgi; Meli, Marina L; Eppler, Elisabeth; Reinecke, Manfred

    2004-06-01

    We developed a one-tube two-temperature real-time RT-PCR that allows to absolutely quantify the gene expression of hormones using the standard curve method. As our research focuses on the expression of the insulin-like growth factors (IGFs) in bony fish, we established the technique for IGF-I and IGF-II using the tilapia (Oreochromis niloticus) as model species. As approach, we used primer extension adding a T7 phage polymerase promoter (21 nt) to the 5' end of the antisense primers. This procedure avoids the disadvantages arising from plasmids. Total RNA extracted from liver was subjected to conventional RT-PCR to create templates for in vitro transcription of IGF-I and IGF-II cRNA. Correct template sizes including the T7 promoter were verified (IGF-I: 91 nt; IGF-II: 94 nt). The PCR products were used to create IGF-I and IGF-II cRNAs which were quantified in dot blot by comparison with defined amounts of standardised kanamycin mRNA. Standardised threshold cycle (Ct) values for IGF-I and IGF-II mRNA were achieved by real-time RT-PCR and used to create standard curves. To allow sample normalisation the standard curve was also established for beta-actin as internal calibrator (template: 86 nt), and validation experiments were performed demonstrating similar amplification efficiencies for target and reference genes. Based on the standard curves, the absolute amounts of IGF-I and IGF-II mRNA were determined for liver (IGF-I: 8.90+/-1.90 pg/microg total RNA, IGF-II: 3.59+/-0.98 pg/microg total RNA) and extrahepatic sites, such as heart, kidney, intestine, spleen, gills, gonad, and brain considering the different lengths of cRNAs and mRNAs by correction factors. The reliability of the method was confirmed in additional experiments. The amplification of descending dilutions of cRNA and total liver RNA resulted in parallel slopes of the amplification curves. Furthermore, amplification plots of the standard cRNA and the IGF-I and IGF-II mRNAs showed signals starting at the

  2. Asteroid absolute magnitudes and slope parameters

    NASA Technical Reports Server (NTRS)

    Tedesco, Edward F.

    1991-01-01

    A new listing of absolute magnitudes (H) and slope parameters (G) has been created and published in the Minor Planet Circulars; this same listing will appear in the 1992 Ephemerides of Minor Planets. Unlike previous listings, the values of the current list were derived from fits of data at the V band. All observations were reduced in the same fashion using, where appropriate, a single basis default value of 0.15 for the slope parameter. Distances and phase angles were computed for each observation. The data for 113 asteroids was of sufficiently high quality to permit derivation of their H and G. These improved absolute magnitudes and slope parameters will be used to deduce the most reliable bias-corrected asteroid size-frequency distribution yet made.

  3. Nature, frequency and determinants of prescription modifications in Dutch community pharmacies

    PubMed Central

    Buurma, Henk; de Smet, Peter A G M; van den Hoff, Olga P; Egberts, Antoine C G

    2001-01-01

    Aims To examine the nature, frequency and determinants of prescription modifications in Dutch community pharmacies. Methods A prospective case-control study comparing modified prescriptions with nonmodified prescriptions was carried out in 141 Dutch community pharmacies. 2014 modified prescriptions (cases), collected in the selected pharmacies on a predetermined day in a specific period (25th February until 12th March 1999) and 2581 nonmodified prescriptions (controls) randomly selected on the same day were studied. The nature and frequency of prescription modifications and patient, drug and prescriber related determinants for a modified prescription were assessed. Results The overall incidence of prescription modifications was 4.3%, with a mean of 14.3 modifications per pharmacy per day. For prescription only medicines (POM) the incidence was 4.9%. The majority of POM modifications concerned a clarification (71.8%). In 22.2% a prescription could potentially have had clinical consequences when not altered; in more than half of the latter it concerned a dose error (13.7% of all cases). POM prescriptions of patients of 40–65 years had a significantly lower chance of modification compared with those of younger people (OR = 0.74 [0.64–0.86]). With respect to medication-class, we found a higher chance of POM modifications in the respiratory domain (OR = 1.48 [1.23-1.79]) and a decreased chance for nervous system POMs (OR = 0.71 [0.61–0.83]). With regard to prescriber-related determinants modifications were found three times more often in non printed prescriptions than in printed ones (OR = 3.30 [2.90-3.75]). Compared with prescriptions by the patient's own GP, prescriptions of specialists (OR = 1.82 [1.57-2.11]), other GP's (OR = 1.49 [1.02-2.17]) and other prescribers such as dentists and midwives (OR = 1.95 [1.06-3.57]) gave a higher probability of prescription modifications. When a GP had no on-line access to the computer of the pharmacy the chance of a

  4. Determination of acoustic properties of thin polymer films utilizing the frequency dependence of the reflection coefficient of ultrasound

    NASA Astrophysics Data System (ADS)

    Tohmyoh, Hironori; Sakamoto, Yuhei

    2015-11-01

    This paper reports on a technique to measure the acoustic properties of a thin polymer film utilizing the frequency dependence of the reflection coefficient of ultrasound reflected back from a system comprising a reflection plate, the film, and a material that covers the film. The frequency components of the echo reflected from the back of the plate, where the film is attached, take their minimum values at the resonant frequency, and from these frequency characteristics, the acoustic impedance, sound velocity, and the density of the film can be determined. We applied this technique to characterize an ion exchange membrane, which has high water absorbability, and successfully determined the acoustic properties of the membrane without getting it wet.

  5. GNSS Single Frequency, Single Epoch Reliable Attitude Determination Method with Baseline Vector Constraint.

    PubMed

    Gong, Ang; Zhao, Xiubin; Pang, Chunlei; Duan, Rong; Wang, Yong

    2015-01-01

    For Global Navigation Satellite System (GNSS) single frequency, single epoch attitude determination, this paper proposes a new reliable method with baseline vector constraint. First, prior knowledge of baseline length, heading, and pitch obtained from other navigation equipment or sensors are used to reconstruct objective function rigorously. Then, searching strategy is improved. It substitutes gradually Enlarged ellipsoidal search space for non-ellipsoidal search space to ensure correct ambiguity candidates are within it and make the searching process directly be carried out by least squares ambiguity decorrelation algorithm (LAMBDA) method. For all vector candidates, some ones are further eliminated by derived approximate inequality, which accelerates the searching process. Experimental results show that compared to traditional method with only baseline length constraint, this new method can utilize a priori baseline three-dimensional knowledge to fix ambiguity reliably and achieve a high success rate. Experimental tests also verify it is not very sensitive to baseline vector error and can perform robustly when angular error is not great. PMID:26633413

  6. GNSS Single Frequency, Single Epoch Reliable Attitude Determination Method with Baseline Vector Constraint

    PubMed Central

    Gong, Ang; Zhao, Xiubin; Pang, Chunlei; Duan, Rong; Wang, Yong

    2015-01-01

    For Global Navigation Satellite System (GNSS) single frequency, single epoch attitude determination, this paper proposes a new reliable method with baseline vector constraint. First, prior knowledge of baseline length, heading, and pitch obtained from other navigation equipment or sensors are used to reconstruct objective function rigorously. Then, searching strategy is improved. It substitutes gradually Enlarged ellipsoidal search space for non-ellipsoidal search space to ensure correct ambiguity candidates are within it and make the searching process directly be carried out by least squares ambiguity decorrelation algorithm (LAMBDA) method. For all vector candidates, some ones are further eliminated by derived approximate inequality, which accelerates the searching process. Experimental results show that compared to traditional method with only baseline length constraint, this new method can utilize a priori baseline three-dimensional knowledge to fix ambiguity reliably and achieve a high success rate. Experimental tests also verify it is not very sensitive to baseline vector error and can perform robustly when angular error is not great. PMID:26633413

  7. Analysis of streambed temperatures in ephemeral channels to determine streamflow frequency and duration

    USGS Publications Warehouse

    Constantz, J.; Stonestrom, D.; Stewart, A.E.; Niswonger, R.; Smith, T.R.

    2001-01-01

    Spatial and temporal patterns in streamflow are rarely monitored for ephemeral streams. Flashy, erosive streamflows common in ephemeral channels create a series of operational and maintenance problems, which makes it impractical to deploy a series of gaging stations along ephemeral channels. Streambed temperature is a robust and inexpensive parameter to monitor remotely, leading to the possibility of analyzing temperature patterns to estimate streamflow frequency and duration along ephemeral channels. A simulation model was utilized to examine various atmospheric and hydrological upper boundary conditions compared with a series of hypothetical temperature-monitoring depths within the streambed. Simulation results indicate that streamflow events were distinguished from changing atmospheric conditions with greater certainty using temperatures at shallow depths (e.g., 10-20 cm) as opposed to the streambed surface. Three ephemeral streams in the American Southwest were instrumented to monitor streambed temperature for determining the accuracy of using this approach to ascertain the long-term temporal and spatial extent of streamflow along each stream channel. Streambed temperature data were collected at the surface or at shallow depth along each stream channel, using thermistors encased in waterproof, single-channel data loggers tethered to anchors in the channel. On the basis of comparisons with site information, such as direct field observations and upstream flow records, diurnal temperature variations successfully detected the presence and duration of streamflow for all sites.

  8. Determining the dispersion characteristics of rivers from the frequency response of the system

    NASA Astrophysics Data System (ADS)

    Lambertz, Peter; Palancar, MaríA. C.; Aragón, José M.; Gil, Roberto

    2006-09-01

    A new method of determining the parameters of an aggregated dead zone model (ADZ) to predict longitudinal dispersion in rivers is presented. The method is based on the frequency response analysis (FRA) of observed field tests, which consist of tracer injections (input) and measurement of tracer in downstream sampling points (output) located downstream from the injection point. The ADZ is a combination of plug and completely mixed flow compartments. The ADZ parameters (number of compartments, mean residence time, and delay time) are evaluated by means of Bode plots that give the system order (number of compartments), gain, time constant (mean residence time of each compartment) and delay time. The FRA-ADZ method was checked with tracer data runs in two Spanish rivers, the Tagus and the Ebro rivers. The experimental tracer concentration versus time distributions were compared with the ADZ predicted curves, which were calculated using parameters obtained from the FRA method, and with curves predicted by several classical models. The residence time of several reaches within the two studied rivers was predicted by the FRA-ADZ method with a relative error lower than 10%. The method is generally applicable to ideal and nonideal inputs and is particularly well suited to arbitrary-shaped initial source concentration distributions.

  9. Determination of Receiver Susceptibility to Radio Frequency Interference from Portable Electronic Devices

    NASA Technical Reports Server (NTRS)

    Nguyen, Truong X.; Ely, Jay J.

    2002-01-01

    With the increasing pressures to allow wireless devices on aircraft, the susceptibility of aircraft receivers to interference from Portable Electronic Devices (PEDs) becomes an increasing concern. Many investigations were conducted in the past, with limited success, to quantify device emissions, path loss, and receiver interference susceptibility thresholds. This paper outlines the recent effort in determining the receiver susceptibility thresholds for ILS, VOR and GPS systems. The effort primarily consists of analysis of data available openly as reported in many RTCA and ICAO documents as well as manufacturers data on receiver sensitivity. Shortcomings with the susceptibility threshold data reported in the RTCA documents are presented, and an approach for an in-depth study is suggested. In addition, intermodulation products were observed and demonstrated in a laboratory experiment when multiple PEDs were in the proximity of each other. These intermodulation effects generate spurious frequencies that may fall within aircraft communication or navigation bands causing undesirable effects. Results from a preliminary analysis are presented that show possible harmful combinations of PEDs and the potentially affected aircraft bands.

  10. Method and apparatus for determining pressure-induced frequency-shifts in shock-compressed materials

    DOEpatents

    Moore, David S.; Schmidt, Stephen C.

    1985-01-01

    A method and an apparatus for conducting coherent anti-Stokes Raman scattering spectroscopy in shock-compressed materials are disclosed. The apparatus includes a sample vessel having an optically transparent wall and an opposing optically reflective wall. Two coherent laser beams, a pump beam and a broadband Stokes beam, are directed through the window and focused on a portion of the sample. In the preferred embodiment, a projectile is fired from a high-pressure gas gun to impact the outside of the reflective wall, generating a planar shock wave which travels through the sample toward the window. The pump and Stokes beams result in the emission from the shock-compressed sample of a coherent anti-Stokes beam, which is emitted toward the approaching reflective wall of the vessel and reflected back through the window. The anti-Stokes beam is folded into a spectrometer for frequency analysis. The results of such analysis are useful for determining chemical and physical phenomena which occur during the shock-compression of the sample.

  11. Method and apparatus for determining pressure-induced frequency-shifts in shock-compressed materials

    DOEpatents

    Moore, D.S.; Schmidt, S.C.

    1983-12-16

    A method and an apparatus for conducting coherent anti-Stokes Raman scattering spectroscopy in shock-compressed materials are disclosed. The apparatus includes a sample vessel having an optically transparent wall and an opposing optically reflective wall. Two coherent laser beams, a pump beam and a broadband Stokes beam, are directed through the window and focused on a portion of the sample. In the preferred embodiment, a projectile is fired from a high-pressure gas gun to impact the outside of the reflective wall, generating a planar shock wave which travels through the sample toward the window. The pump and Stokes beams result in the emission from the shock-compressed sample of a coherent anti-Stokes beam, which is emitted toward the approaching reflective wall of the vessel and reflected back through the window. The anti-Stokes beam is folded into a spectrometer for frequency analysis. The results of such analysis are useful for determining chemical and physical phenomena which occur during the shock-compression of the sample.

  12. Absolute quantification of UGT1A1 in various tissues and cell lines using isotope label-free UPLC-MS/MS method determines its turnover number and correlates with its glucuronidation activities.

    PubMed

    Xu, Beibei; Gao, Song; Wu, Baojian; Yin, Taijun; Hu, Ming

    2014-01-01

    Uridine 5'-diphosphate-glucuronosyltransferase (UGT)1A1 is a major phase II metabolism enzyme responsible for glucuronidation of drugs and endogenous compounds. The purpose of this study was to determine the expression level of UGT1A1 in human liver microsomes and human cell lines by using an isotope label-free LC-MS/MS method. A Waters Ultra performance liquid chromatography (UPLC) system coupled with an API 5500Qtrap mass spectrometer was used for the analysis. Two signature peptides (Pep-1, and Pep-2) were employed to quantify UGT1A1 by multiple reaction monitoring (MRM) approach. Standard addition method was used to validate the assay to account for the matrix effect. 17β-Estradiol was used as the marker substrate to determine UGT1A1 activities. The validated method has a linear range of 200-0.0195nM for both signature peptides. The precision, accuracy, and matrix effect were in acceptable ranges. UGT1A1 expression levels were then determined using 8 individual human liver microsomes, a pooled human liver microsomes, three UGT1A1 genotyped human liver microsomes, and four cell lines (Caco-2, MCF-7, Hela, and HepG2). The correlations study showed that the UGT1A1 protein levels were strongly correlated with its glucuronidation activities in human liver microsomes (R(2)=0.85) and in microsomes prepared from cell lines (R(2)=0.95). Isotope-labeled peptides were not necessary for LC-MS/MS quantitation of proteins. The isotope label-free absolute quantification method used here had good accuracy, sensitivity, linear range, and reproducibility, and were used successfully for the accurate determination of UGT1A1 from tissues and cell lines. PMID:24055854

  13. Can the state of platinum species be unambiguously determined by the stretching frequency of an adsorbed CO probe molecule?

    PubMed

    Aleksandrov, Hristiyan A; Neyman, Konstantin M; Hadjiivanov, Konstantin I; Vayssilov, Georgi N

    2016-08-10

    The paper addresses possible ambiguities in the determination of the state of platinum species by the stretching frequency of a CO probe, which is a common technique for characterization of platinum-containing catalytic systems. We present a comprehensive comparison of the available experimental data with our theoretical modeling (density functional) results of pertinent systems - platinum surfaces, nanoparticles and clusters as well as reduced or oxidized platinum moieties on a ceria support. Our results for CO adsorbed on-top on metallic Pt(0), with C-O vibrational frequencies in the region 2018-2077 cm(-1), suggest that a decrease of the coordination number of the platinum atom, to which CO is bound, by one lowers the CO frequency by about 7 cm(-1). This trend corroborates the Kappers-van der Maas correlation derived from the analysis of the experimental stretching frequency of CO adsorbed on platinum-containing samples on different supports. We also analyzed the effect of the charge of platinum species on the CO frequency. Based on the calculated vibrational frequencies of CO in various model systems, we concluded that the actual state of the platinum species may be mistaken based only on the measured value of the C-O vibrational frequency due to overlapping regions of frequencies corresponding to different types of species. In order to identify the actual state of platinum species one has to combine this powerful technique with other approaches. PMID:27444400

  14. Quantitative, depth-resolved determination of particle motion using multi-exposure, spatial frequency domain laser speckle imaging

    PubMed Central

    Rice, Tyler B.; Kwan, Elliott; Hayakawa, Carole K.; Durkin, Anthony J.; Choi, Bernard; Tromberg, Bruce J.

    2013-01-01

    Laser Speckle Imaging (LSI) is a simple, noninvasive technique for rapid imaging of particle motion in scattering media such as biological tissue. LSI is generally used to derive a qualitative index of relative blood flow due to unknown impact from several variables that affect speckle contrast. These variables may include optical absorption and scattering coefficients, multi-layer dynamics including static, non-ergodic regions, and systematic effects such as laser coherence length. In order to account for these effects and move toward quantitative, depth-resolved LSI, we have developed a method that combines Monte Carlo modeling, multi-exposure speckle imaging (MESI), spatial frequency domain imaging (SFDI), and careful instrument calibration. Monte Carlo models were used to generate total and layer-specific fractional momentum transfer distributions. This information was used to predict speckle contrast as a function of exposure time, spatial frequency, layer thickness, and layer dynamics. To verify with experimental data, controlled phantom experiments with characteristic tissue optical properties were performed using a structured light speckle imaging system. Three main geometries were explored: 1) diffusive dynamic layer beneath a static layer, 2) static layer beneath a diffuse dynamic layer, and 3) directed flow (tube) submerged in a dynamic scattering layer. Data fits were performed using the Monte Carlo model, which accurately reconstructed the type of particle flow (diffusive or directed) in each layer, the layer thickness, and absolute flow speeds to within 15% or better. PMID:24409388

  15. SuperFreq: Numerical determination of fundamental frequencies of an orbit

    NASA Astrophysics Data System (ADS)

    Price-Whelan, Adrian M.

    2015-11-01

    SuperFreq numerically estimates the fundamental frequencies and orbital actions of pre-computed orbital time series. It is an implementation of a version of the Numerical Analysis of Fundamental Frequencies close to that by Monica Valluri in NAFF, which itself is an implementation of an algorithm first used by Jacques Laskar.

  16. Self-adaptive method for high-frequency dispersion curve determination

    Technology Transfer Automated Retrieval System (TEKTRAN)

    When high-frequency (from 50 to 500 Hz) MASW is conducted to explore soil profile in the vadose zone, existing rules for selecting near offset and receiver spread length cannot satisfy the requirements of planar and dominant Rayleigh waves for all frequencies and will inevitably introduce near and f...

  17. Improving HST Pointing & Absolute Astrometry

    NASA Astrophysics Data System (ADS)

    Lallo, Matthew; Nelan, E.; Kimmer, E.; Cox, C.; Casertano, S.

    2007-05-01

    Accurate absolute astrometry is becoming increasingly important in an era of multi-mission archives and virtual observatories. Hubble Space Telescope's (HST's) Guidestar Catalog II (GSC2) has reduced coordinate error to around 0.25 arcsecond, a factor 2 or more compared with GSC1. With this reduced catalog error, special attention must be given to calibrate and maintain the Fine Guidance Sensors (FGSs) and Science Instruments (SIs) alignments in HST to a level well below this in order to ensure that the accuracy of science product's astrometry keywords and target positioning are limited only by the catalog errors. After HST Servicing Mission 4, such calibrations' improvement in "blind" pointing accuracy will allow for more efficient COS acquisitions. Multiple SIs and FGSs each have their own footprints in the spatially shared HST focal plane. It is the small changes over time in primarily the whole-body positions & orientations of these instruments & guiders relative to one another that is addressed by this work. We describe the HST Cycle 15 program CAL/OTA 11021 which, along with future variants of it, determines and maintains positions and orientations of the SIs and FGSs to better than 50 milli- arcseconds and 0.04 to 0.004 degrees of roll, putting errors associated with the alignment sufficiently below GSC2 errors. We present recent alignment results and assess their errors, illustrate trends, and describe where and how the observer sees benefit from these calibrations when using HST.

  18. Determining correspondences between high-frequency MedDRA concepts and SNOMED: a case study

    PubMed Central

    2010-01-01

    Background The Systematic Nomenclature of Medicine Clinical Terms (SNOMED CT) is being advocated as the foundation for encoding clinical documentation. While the electronic medical record is likely to play a critical role in pharmacovigilance - the detection of adverse events due to medications - classification and reporting of Adverse Events is currently based on the Medical Dictionary of Regulatory Activities (MedDRA). Complete and high-quality MedDRA-to-SNOMED CT mappings can therefore facilitate pharmacovigilance. The existing mappings, as determined through the Unified Medical Language System (UMLS), are partial, and record only one-to-one correspondences even though SNOMED CT can be used compositionally. Efforts to map previously unmapped MedDRA concepts would be most productive if focused on concepts that occur frequently in actual adverse event data. We aimed to identify aspects of MedDRA that complicate mapping to SNOMED CT, determine pattern in unmapped high-frequency MedDRA concepts, and to identify types of integration errors in the mapping of MedDRA to UMLS. Methods Using one years' data from the US Federal Drug Administrations Adverse Event Reporting System, we identified MedDRA preferred terms that collectively accounted for 95% of both Adverse Events and Therapeutic Indications records. After eliminating those already mapping to SNOMED CT, we attempted to map the remaining 645 Adverse-Event and 141 Therapeutic-Indications preferred terms with software assistance. Results All but 46 Adverse-Event and 7 Therapeutic-Indications preferred terms could be composed using SNOMED CT concepts: none of these required more than 3 SNOMED CT concepts to compose. We describe the common composition patterns in the paper. About 30% of both Adverse-Event and Therapeutic-Indications Preferred Terms corresponded to single SNOMED CT concepts: the correspondence was detectable by human inspection but had been missed during the integration process, which had created

  19. Elastic Constants of Single Crystal Stishovite Determined by High Frequency Resonant Ultrasound Spectroscopy (HRUS)

    NASA Astrophysics Data System (ADS)

    Yoneda, A.; Cooray, T.; Shatskiy, A.; Sohag, H.

    2010-12-01

    Elastic properties of minerals plays an indispensable role in the studies of Earth's interior as it is essential for interpretation of seismic velocity structure of the Earth, due to its feasibility of comparison with the seismological observations. And it also provides information on structure, bonding, and the nature of phase transitions in minerals. Resonant Ultrasound Spectroscopy (RUS) has been one of the leading methods of determining elastic constants of materials by measuring number of natural vibration modes. Owing to developments of high frequency RUS up to 50 MHz (HRUS), it emerge as a powerful technique in study of high pressure phases of mantel minerals in which samples are restricted to be sub millimeter size. In this study stishovite was selected due to exceptional interest on it as a prototype phase of the lower mantle silicates, because it exhibits silicon in six-fold coordination. Large single crystals (up to 0.8x0.8x1.5mm) of stishovite were synthesized at 12 GPa from single crystal quartz and water (SiO2+15wt% H2O) by slow cooling method (from 1450 C to 800 C) in Kawai-type uniaxial split sphere apparatus (USSA5000). Quality of the crystals was confirmed by polarized microscope study, micro focus x-ray diffractometry and precision x-ray diffractometry. From FTIR measurements water content in synthesized crystals was confirmed to be less than 7 wt. ppm. Crystal was grind and polished into a rectangle, parallel to crystallographic axis having edges of 230x290x500 micron meter. Then it was measured with HRUS for ~20 resonance peaks between 6-20 MHz range. From these peaks, six independent elastic constants C11 = 449 GPa, C33 = 775 GPa, C12 = 200 GPa, C13 = 198 GPa, C44 = 254 GPa and C66 = 318 GPa were determined through a kind of inversion analysis . Although the present C11 value is slightly smaller than previous Brillouin scattering data, other five elastic constants are within the scatter among Brillouin scattering data.

  20. Reassessing word frequency as a determinant of word recognition for skilled and unskilled readers

    PubMed Central

    Kuperman, Victor; Van Dyke, Julie A.

    2013-01-01

    The importance of vocabulary in reading comprehension emphasizes the need to accurately assess an individual’s familiarity with words. The present article highlights problems with using occurrence counts in corpora as an index of word familiarity, especially when studying individuals varying in reading experience. We demonstrate via computational simulations and norming studies that corpus-based word frequencies systematically overestimate strengths of word representations, especially in the low-frequency range and in smaller-size vocabularies. Experience-driven differences in word familiarity prove to be faithfully captured by the subjective frequency ratings collected from responders at different experience levels. When matched on those levels, this lexical measure explains more variance than corpus-based frequencies in eye-movement and lexical decision latencies to English words, attested in populations with varied reading experience and skill. Furthermore, the use of subjective frequencies removes the widely reported (corpus) frequency-by-skill interaction, showing that more skilled readers are equally faster in processing any word than the less skilled readers, not disproportionally faster in processing lower-frequency words. This finding challenges the view that the more skilled an individual is in generic mechanisms of word processing the less reliant he/she will be on the actual lexical characteristics of that word. PMID:23339352

  1. Reassessing word frequency as a determinant of word recognition for skilled and unskilled readers.

    PubMed

    Kuperman, Victor; Van Dyke, Julie A

    2013-06-01

    The importance of vocabulary in reading comprehension emphasizes the need to accurately assess an individual's familiarity with words. The present article highlights problems with using occurrence counts in corpora as an index of word familiarity, especially when studying individuals varying in reading experience. We demonstrate via computational simulations and norming studies that corpus-based word frequencies systematically overestimate strengths of word representations, especially in the low-frequency range and in smaller-size vocabularies. Experience-driven differences in word familiarity prove to be faithfully captured by the subjective frequency ratings collected from responders at different experience levels. When matched on those levels, this lexical measure explains more variance than corpus-based frequencies in eye-movement and lexical decision latencies to English words, attested in populations with varied reading experience and skill. Furthermore, the use of subjective frequencies removes the widely reported (corpus) Frequency × Skill interaction, showing that more skilled readers are equally faster in processing any word than the less skilled readers, not disproportionally faster in processing lower frequency words. This finding challenges the view that the more skilled an individual is in generic mechanisms of word processing, the less reliant he or she will be on the actual lexical characteristics of that word. PMID:23339352

  2. Determination of the absolute configuration of chiral α-aryloxypropanoic acids using vibrational circular dichroism studies: 2-(2-chlorophenoxy) propanoic acid and 2-(3-chlorophenoxy) propanoic acid

    NASA Astrophysics Data System (ADS)

    He, Jiangtao; Polavarapu, Prasad L.

    2005-05-01

    The enantiomers of 2-(2-chlorophenoxy) propanoic acid and 2-(3-chlorophenoxy) propanoic acid were resolved on a chiral HPLC column and investigated using mid-infrared vibrational circular dichroism (VCD). Experimental infrared vibrational absorption and VCD spectra were measured in CDCl 3 solution in the 2000-900 cm -1 region and compared with the ab initio predictions of absorption and VCD spectra. The predicted spectra were obtained with density functional theory using B3LYP/6-31G* basis set for the stable and dominant conformers. But the predicted spectra did not provide unambiguous structural information due to intermolecular hydrogen bonding in solution. To eliminate the hydrogen bonding effects, the acids were converted to the corresponding methyl esters and the experimental absorbance and VCD spectra of methyl esters were measured. B3LYP predicted spectra were also obtained for the stable and dominant conformers of the esters. From a comparison of the experimental VCD spectra of methyl esters with corresponding ab initio predictions, the absolute configurations of esters, and therefore of their parent acids, are unambiguously determined to be (+)-( R).

  3. Redetermining CEBAF's Absolute Energy

    NASA Astrophysics Data System (ADS)

    Su, Tong; Jlab Marathon Collaboration

    2015-04-01

    With the upgrade of the Jefferson Lab accelerator (CEBAF) from 6 GeV max energy to 12 GeV, all the dipole magnets in the machine were refurbished. Most of them were switched from open c-shaped to closed h-shaped by adding extra iron. With these upgraded magnets, the energy calibration of the accelerator needed to be redetermined. We will show how an extra external dipole, which is run in series with those in the machine, helps us cross check the current in the magnets as well as precisely map out the integral field for any machine setting. Using knowledge of the relative performance of the dipoles as well as the bend angle into the Hall, has allowed us to already determine a 4th pass 7 GeV beam to better than 7 MeV. In the future, we will use g-2 spin precession as a second independent energy determination. This work is supported by Kent State University, NSF Grant PHY-1405814, and DOE Contract DE-AC05-06OR23177 (JLab).

  4. Absolute ultrasonic displacement amplitude measurements with a submersible electrostatic acoustic transducer

    NASA Technical Reports Server (NTRS)

    Yost, William T.; Cantrell, John H.

    1992-01-01

    An experimental technique for absolute measurement of ultrasonic wave particle displacement amplitudes in liquids is reported. The technique is capable of measurements over a frequency range of two decades with a sensitivity less than one angstrom. The technique utilizes a previously reported submersible electrostatic acoustic transducer (ESAT) featuring a conductive membrane stretched over a recessed electrode. An uncertainty analysis shows that the displacement amplitude of an ultrasonic plane wave incident on the ESAT can be experimentally determined to better than 2.3-4 percent, depending on frequency, in the frequency range of 0.5-15 MHz. Membranes with lower and more uniform areal densities can improve the accuracy and extend the operation to higher frequencies.

  5. Determining the frequency of sporadic cases of rare X-linked disorders

    PubMed Central

    2016-01-01

    This paper gives formulae for calculating the gene frequency, incidence and proportion of sporadic cases of rare X-linked recessive disorders, taking account of the possibility of early recognition of carriers and fitness of affected males. PMID:27004222

  6. Metallic Magnetic Calorimeters for Absolute Activity Measurement

    NASA Astrophysics Data System (ADS)

    Loidl, M.; Leblanc, E.; Rodrigues, M.; Bouchard, J.; Censier, B.; Branger, T.; Lacour, D.

    2008-05-01

    We present a prototype of metallic magnetic calorimeters that we are developing for absolute activity measurements of low energy emitting radionuclides. We give a detailed description of the realization of the prototype, containing an 55Fe source inside the detector absorber. We present the analysis of first data taken with this detector and compare the result of activity measurement with liquid scintillation counting. We also propose some ways for reducing the uncertainty on the activity determination with this new technique.

  7. A new method for determining the plasma electron density using optical frequency comb interferometer

    SciTech Connect

    Arakawa, Hiroyuki Tojo, Hiroshi; Sasao, Hajime; Kawano, Yasunori; Itami, Kiyoshi

    2014-04-15

    A new method of plasma electron density measurement using interferometric phases (fractional fringes) of an optical frequency comb interferometer is proposed. Using the characteristics of the optical frequency comb laser, high density measurement can be achieved without fringe counting errors. Simulations show that the short wavelength and wide wavelength range of the laser source and low noise in interferometric phases measurements are effective to reduce ambiguity of measured density.

  8. Determining the magnitude, frequency and source of prehistoric events - Is there a Holy Grail?

    NASA Astrophysics Data System (ADS)

    Goff, James; Dominey-Howes, Dale; Chague-Goff, Catherine; Strotz, Luke; Anning, David; Bird, Deanne; Calgaro, Emma; Courtney, Claire

    2010-05-01

    palaeotsunami sources, we need to be able to compare and contrast between national databases. This can only happen if databases exist and are compatible - for example, are the criteria used for palaeotsunami interpretations consistent? Similarly, to be able to start commenting on the magnitude and frequency of palaeotsunamis from local, regional and distant sources there need to be regional and national databases to refer to. Surprisingly, this is rarely the case. We highlight this issue with reference to palaeotsunami data from the Pacific Ocean. Palaeotsunami magnitude, frequency and source (PMFS) modelling can be and has been achieved albeit with some caution. While it is acknowledged that any single palaeotsunami database will never be entirely complete and we may therefore never be fully able to determine the PMFS for any one region, this does not mean that is has no value. Far from it, after all every single historical database is also incomplete and they are regularly used for probabilistic tsunami hazard modelling. Is there a Holy Grail? In many ways it largely depends upon whether you think the cup is half full or half empty.

  9. Crack depth determination by ultrasonic frequency analysis aided by dynamic photoelasticity

    SciTech Connect

    Singh, A.

    1980-08-01

    A non-destructive method for characterizing the depth of artificial surface-breaking flaws (slots) using Rayleigh surface waves is described. Dynamic photoelasticity was used to obtain a full-field visualization of the waves generated on interaction of a Rayleigh wave with a slot. This visualization showed that for slot lengths of the same order of size as the predominant wavelengths in the incident Rayleigh wave, there is a significant interaction of the subsurface Rayleigh disturbance with the slot tip, producing transmitted surface disturbances that were quantitatively analyzed. Specifically, the frequency content of these transmitted waves was found for four different slot depths. The high frequency components of these transmitted signals exhibited a maximum frequency which decreased with increasing slot depth. This was attributed to the fact that the maximum frequencies of the subsurface field of the incident Rayleigh wave decrease with increasing depth. Ultrasonic testing was also done on surface slots in steel blocks, using commercial Rayleigh wave transducers. A relationship similar to the photoelastic results was obtained for the frequency components of the transmitted waves at the surface relative to the slot depth. However, in the ultrasonic case, there was a definite high frequency cut off point which could be directly related to the slot depth for slots perpendicular to the surface. This relationship was shown to also accurately predict the depth of inclined slots.

  10. Determining the population frequency of the CFHR3/CFHR1 deletion at 1q32.

    PubMed

    Holmes, Lucy V; Strain, Lisa; Staniforth, Scott J; Moore, Iain; Marchbank, Kevin; Kavanagh, David; Goodship, Judith A; Cordell, Heather J; Goodship, Timothy H J

    2013-01-01

    In this study we have used multiplex ligation-dependent probe amplification (MLPA) to measure the copy number of CFHR3 and CFHR1 in DNA samples from 238 individuals from the UK and 439 individuals from the HGDP-CEPH Human Genome Diversity Cell Line Panel. We have then calculated the allele frequency and frequency of homozygosity for the copy number polymorphism represented by the CFHR3/CFHR1 deletion. There was a highly significant difference between geographical locations in both the allele frequency (X(2)  = 127.7, DF = 11, P-value = 4.97x10(-22)) and frequency of homozygosity (X(2)  = 142.3, DF = 22, P-value = 1.33x10(-19)). The highest frequency for the deleted allele (54.7%) was seen in DNA samples from Nigeria and the lowest (0%) in samples from South America and Japan. The observed frequencies in conjunction with the known association of the deletion with AMD, SLE and IgA nephropathy is in keeping with differences in the prevalence of these diseases in African and European Americans. This emphasises the importance of identifying copy number polymorphism in disease. PMID:23613724

  11. Absolute dosimetry for extreme-ultraviolet lithography

    NASA Astrophysics Data System (ADS)

    Berger, Kurt W.; Campiotti, Richard H.

    2000-06-01

    The accurate measurement of an exposure dose reaching the wafer on an extreme ultraviolet (EUV) lithographic system has been a technical challenge directly applicable to the evaluation of candidate EUV resist materials and calculating lithography system throughputs. We have developed a dose monitoring sensor system that can directly measure EUV intensities at the wafer plane of a prototype EUV lithographic system. This sensor system, located on the wafer stage adjacent to the electrostatic chuck used to grip wafers, operates by translating the sensor into the aerial image, typically illuminating an 'open' (unpatterned) area on the reticle. The absolute signal strength can be related to energy density at the wafer, and thus used to determine resist sensitivity, and the signal as a function of position can be used to determine illumination uniformity at the wafer plane. Spectral filtering to enhance the detection of 13.4 nm radiation was incorporated into the sensor. Other critical design parameters include the packaging and amplification technologies required to place this device into the space and vacuum constraints of a EUV lithography environment. We describe two approaches used to determine the absolute calibration of this sensor. The first conventional approach requires separate characterization of each element of the sensor. A second novel approach uses x-ray emission from a mildly radioactive iron source to calibrate the absolute response of the entire sensor system (detector and electronics) in a single measurement.

  12. Detection of MPLW515L/K Mutations and Determination of Allele Frequencies with a Single-Tube PCR Assay

    PubMed Central

    Takei, Hiraku; Morishita, Soji; Araki, Marito; Edahiro, Yoko; Sunami, Yoshitaka; Hironaka, Yumi; Noda, Naohiro; Sekiguchi, Yuji; Tsuneda, Satoshi; Ohsaka, Akimichi; Komatsu, Norio

    2014-01-01

    A gain-of-function mutation in the myeloproliferative leukemia virus (MPL) gene, which encodes the thrombopoietin receptor, has been identified in patients with essential thrombocythemia and primary myelofibrosis, subgroups of classic myeloproliferative neoplasms (MPNs). The presence of MPL gene mutations is a critical diagnostic criterion for these diseases. Here, we developed a rapid, simple, and cost-effective method of detecting two major MPL mutations, MPLW515L/K, in a single PCR assay; we termed this method DARMS (dual amplification refractory mutation system)-PCR. DARMS-PCR is designed to produce three different PCR products corresponding to MPLW515L, MPLW515K, and all MPL alleles. The amplicons are later detected and quantified using a capillary sequencer to determine the relative frequencies of the mutant and wild-type alleles. Applying DARMS-PCR to human specimens, we successfully identified MPL mutations in MPN patients, with the exception of patients bearing mutant allele frequencies below the detection limit (5%) of this method. The MPL mutant allele frequencies determined using DARMS-PCR correlated strongly with the values determined using deep sequencing. Thus, we demonstrated the potential of DARMS-PCR to detect MPL mutations and determine the allele frequencies in a timely and cost-effective manner. PMID:25144224

  13. Determination and Comparison of Carbonyl Stretching Frequency of a Ketone in Its Ground State and the First Electronic Excited State

    ERIC Educational Resources Information Center

    Bandyopadhyay, Subhajit; Roy, Saswata

    2014-01-01

    This paper describes an inexpensive experiment to determine the carbonyl stretching frequency of an organic keto compound in its ground state and first electronic excited state. The experiment is simple to execute, clarifies some of the fundamental concepts of spectroscopy, and is appropriate for a basic spectroscopy laboratory course. The…

  14. Comparing the frequency of hypertension determined by peri-dialysis measurement and ABPM in hemodialysis patients.

    PubMed

    Abbasi, Mohammad-Reza; Lessan-Pezeshki, Mahboob; Najafi, Mohammad-Taghi; Gatmiri, Seyed-Mansour; Karbakhsh, Mojgan; Mohebi-Nejad, Azin

    2014-06-01

    Controlling blood pressure in hemodialysis patients is crucial but not always easy. The most common blood pressure measurement method is peri-dialysis measurement, but due to interdialytic blood pressure fluctuations, we are unsure if it is the proper way for evaluating blood pressure. Some studies have shown the superiority of 24-h ambulatory blood pressure monitoring over peri-dialysis blood pressure measurement. We aimed to compare the consistency of these methods in determining hypertension among hemodialysis patients. We studied 50 patients (mean age: 55.8 years) on regular hemodialysis in Imam Khomeini University Hospital, Tehran, Iran. Peri-dialysis blood pressure and interdialytic 24-h ambulatory blood pressure monitoring were recorded for each patient. Patients' demographic data and peri-dialysis weight were recorded too. All data were analyzed using the PASW Statistics 18.0, SPSS Inc. (Chicago, IL). There was a significant difference between pre-dialysis mean systolic blood pressure (146.1 ± 23.3 mmHg) and mean systolic blood pressure recorded by ambulatory blood pressure monitoring (135.3 ± 19.3 mmHg) (p = 0.001). There was also a significant difference between pre-dialysis mean diastolic blood pressure (83 ± 14 mmHg) and mean diastolic blood pressure recorded by ambulatory blood pressure monitoring (77.3 ± 10 mmHg) (p = 0.003). But the frequencies of hypertension measured with both methods were significantly consistent and the Kappa agreement coefficient was 0.525 (p = 0.001). Considering ambulatory blood pressure monitoring as the gold standard for blood pressure measurement, our recommendation for the best cutoff point to diagnose hypertension, with the highest sensitivity and specificity would be 135/80 mmHg for pre-dialysis blood pressure and 115/70 mmHg for post-dialysis blood pressure. PMID:24502240

  15. Radar frequency dielectric dispersion in sandstone: Implications for determination of moisture and clay content

    NASA Astrophysics Data System (ADS)

    West, L. Jared; Handley, Kirk; Huang, Yi; Pokar, Magdeline

    2003-02-01

    The relationship between dielectric permittivity, water saturation, and clay content for the Sherwood Sandstone from NE England was characterized as part of a wider study of the vadose zone moisture dynamics and pollution vulnerability of this aquifer. Dielectric permittivity was measured over the full range of saturation levels, for various lithologies ranging from clean medium-grained sandstone to fine-grained sandstone containing up to 5% clay, using a specially constructed dielectric cell. Dielectric constant, Kr, is largely independent of frequency between 350 MHz and 1000 MHz. Below 350 MHz, Kr of fine-grained, clay-rich sandstone shows frequency dispersion. Tests on physical models of the sandstone consisting of a fine fraction of Ottawa Sand and montmorillonite clay indicate that the clay minerals within the sandstone are responsible for its frequency dispersive behavior. These tests also show that increasing pore fluid salinity increases dielectric dispersion at the lower end of the frequency range, which indicates that this arises from the interfacial Maxwell-Wagner mechanism associated with platy clay particles. Water saturated sand:clay mixtures show very low dielectric constants at high frequencies (over 650 MHz). This effect is independent of salinity and probably results from the layered geometric arrangement of solids, bound and free water within the swelling clay. The complex refractive index method (CRIM) with a mineral dielectric constant of about 5 provides a good match to the water saturation versus dielectric constant data for all Sherwood Sandstone lithologies at frequencies between 350 and 1000 MHz and for clay-poor sandstone at lower frequencies. Below 350 MHz the presence of a few percent of clay in some Sherwood Sandstone lithologies raises their CRIM best fit mineral dielectric constant substantially.

  16. Determination of knockdown resistance allele frequencies in global human head louse populations using the serial invasive signal amplification reaction

    PubMed Central

    Hodgdon, Hilliary E.; Yoon, Kyong Sup; Previte, Domenic J.; Kim, Hyo Jeong; Aboelghar, Gamal E.; Lee, Si Hyeock; Clark, J. Marshall

    2010-01-01

    BACKGROUND Pediculosis is the most prevalent parasitic infestation of humans. Resistance to pyrethrin- and pyrethroid-based pediculicides is due to knockdown (kdr)-type point mutations in the voltage-sensitive sodium channel α-subunit gene. Early detection of resistance is crucial for the selection of effective management strategies. RESULTS Kdr allele frequencies of lice from 14 countries were determined using serial invasive signal amplification reaction. Lice collected from Uruguay, UK and Australia had kdr allele frequencies of 100% while lice from Ecuador, Papua New Guinea, South Korea and Thailand had kdr allele frequencies of 0%. The remaining 7 countries investigated, including seven US populations, two Argentina, Brazil, Denmark, Czech Republic, Egypt and Israel, displayed variable kdr allele frequencies, ranging from 11% to 97%. CONCLUSION The newly developed and validated SISAR method is suitable for accurate monitoring of kdr allele frequencies in head lice. Proactive management is needed where kdr-type resistance is not yet saturated. Based on sodium channel insensitivity and its occurrence in louse populations resistant to pyrethrin- and pyrethroid-based pediculicides, the T917I mutation appears a key marker for resistance. Results from the Egyptian population, however, indicate that phenotypic resistance of lice with single or double mutations (M815I and/or L920F) should also be determined. PMID:20564731

  17. Determination of nanovibration amplitudes using frequency-modulated semiconductor laser autodyne

    SciTech Connect

    Usanov, D A; Skripal, A V; Astakhov, E I

    2014-02-28

    The method for measuring nanovibration amplitudes using the autodyne signal of a semiconductor laser at several laser radiation wavelengths is described. The theoretical description of the frequency-modulated autodyne signal under harmonic vibrations of the reflector is presented and the relations for its spectral components are derived using the expansions into the Fourier and Bessel series. The results of numerical modelling based on the proposed method for measuring the reflector nanovibration amplitudes are presented that make use of the low-frequency spectrum of the autodyne signal from the frequency-modulated laser autodyne and the solution of the appropriate inverse problem. The experimental setup is described; the results of the measurements are presented for the nanovibration amplitudes and the autodyne signal spectra under the reflector nanovibrations. (laser applications and other topics in quantum electronics)

  18. Fully Automatic Determination of Soil Bacterium Numbers, Cell Volumes, and Frequencies of Dividing Cells by Confocal Laser Scanning Microscopy and Image Analysis

    PubMed Central

    Bloem, J.; Veninga, M.; Shepherd, J.

    1995-01-01

    We describe a fully automatic image analysis system capable of measuring cell numbers, volumes, lengths, and widths of bacteria in soil smears. The system also determines the number of cells in agglomerates and thus provides the frequency of dividing cells (FDC). Images are acquired from a confocal laser scanning microscope. The grey images are smoothed by convolution and by morphological erosion and dilation to remove noise. The background is equalized by flooding holes in the image and is then subtracted by two top hat transforms. Finally, the grey image is sharpened by delineation, and all particles above a fixed threshold are detected. The number of cells in each detected particle is determined by counting the number of local grey-level maxima in the particle. Thus, up to 1,500 cells in 10 fields of view in a soil smear are analyzed in 30 min without human intervention. Automatic counts of cell numbers and FDC were similar to visual counts in field samples. In microcosms, automatic measurements showed significant increases in cell numbers, FDC, mean cell volume, and length-to-width ratio after amendment of the soil. Volumes of fluorescent microspheres were measured with good approximation, but the absolute values obtained were strongly affected by the settings of the detector sensitivity. Independent measurements of bacterial cell numbers and volumes by image analysis and of cell carbon by a total organic carbon analyzer yielded an average specific carbon content of 200 fg of C (mu)m(sup-3), which indicates that our volume estimates are reasonable. PMID:16534976

  19. Clock time is absolute and universal

    NASA Astrophysics Data System (ADS)

    Shen, Xinhang

    2015-09-01

    A critical error is found in the Special Theory of Relativity (STR): mixing up the concepts of the STR abstract time of a reference frame and the displayed time of a physical clock, which leads to use the properties of the abstract time to predict time dilation on physical clocks and all other physical processes. Actually, a clock can never directly measure the abstract time, but can only record the result of a physical process during a period of the abstract time such as the number of cycles of oscillation which is the multiplication of the abstract time and the frequency of oscillation. After Lorentz Transformation, the abstract time of a reference frame expands by a factor gamma, but the frequency of a clock decreases by the same factor gamma, and the resulting multiplication i.e. the displayed time of a moving clock remains unchanged. That is, the displayed time of any physical clock is an invariant of Lorentz Transformation. The Lorentz invariance of the displayed times of clocks can further prove within the framework of STR our earth based standard physical time is absolute, universal and independent of inertial reference frames as confirmed by both the physical fact of the universal synchronization of clocks on the GPS satellites and clocks on the earth, and the theoretical existence of the absolute and universal Galilean time in STR which has proved that time dilation and space contraction are pure illusions of STR. The existence of the absolute and universal time in STR has directly denied that the reference frame dependent abstract time of STR is the physical time, and therefore, STR is wrong and all its predictions can never happen in the physical world.

  20. Precision absolute value amplifier for a precision voltmeter

    SciTech Connect

    Hearn, W. E.; Rondeau, D. J.

    1985-05-21

    Bipolar inputs are afforded by the plus inputs of first and second differential input amplifiers. A first gain determining resister is connected between the minus inputs of the differential amplifiers. First and second diodes are connected between the respective minus inputs and the respective outputs of the differential amplifiers. First and second FETs have their gates connected to the outputs of the amplifiers, while their respective source and drain circuits are connected between the respective minus inputs and an output lead extending to a load resister. The output current through the load resister is proportional to the absolute value of the input voltage difference between the bipolar input terminals. A third differential amplifier has its plus input terminal connected to the load resister. A second gain determining resister is connected between the minus input of the third differential amplifier and a voltage source. A third FET has its gate connected to the output of the third amplifier. The source and drain circuit of the third transistor is connected between the minus input of the third amplifier and a voltage-frequency converter, constituting an output device. A polarity detector is also provided, comprising a pair of transistors having their inputs connected to the outputs of the first and second differential amplifiers. The outputs of the polarity detector are connected to gates which switch the output of the voltage-frequency converter between up and down counting outputs.

  1. Precision absolute value amplifier for a precision voltmeter

    DOEpatents

    Hearn, William E.; Rondeau, Donald J.

    1985-01-01

    Bipolar inputs are afforded by the plus inputs of first and second differential input amplifiers. A first gain determining resister is connected between the minus inputs of the differential amplifiers. First and second diodes are connected between the respective minus inputs and the respective outputs of the differential amplifiers. First and second FETs have their gates connected to the outputs of the amplifiers, while their respective source and drain circuits are connected between the respective minus inputs and an output lead extending to a load resister. The output current through the load resister is proportional to the absolute value of the input voltage difference between the bipolar input terminals. A third differential amplifier has its plus input terminal connected to the load resister. A second gain determining resister is connected between the minus input of the third differential amplifier and a voltage source. A third FET has its gate connected to the output of the third amplifier. The source and drain circuit of the third transistor is connected between the minus input of the third amplifier and a voltage-frequency converter, constituting an output device. A polarity detector is also provided, comprising a pair of transistors having their inputs connected to the outputs of the first and second differential amplifiers. The outputs of the polarity detector are connected to gates which switch the output of the voltage-frequency converter between up and down counting outputs.

  2. Precision absolute-value amplifier for a precision voltmeter

    DOEpatents

    Hearn, W.E.; Rondeau, D.J.

    1982-10-19

    Bipolar inputs are afforded by the plus inputs of first and second differential input amplifiers. A first gain determining resistor is connected between the minus inputs of the differential amplifiers. First and second diodes are connected between the respective minus inputs and the respective outputs of the differential amplifiers. First and second FETs have their gates connected to the outputs of the amplifiers, while their respective source and drain circuits are connected between the respective minus inputs and an output lead extending to a load resistor. The output current through the load resistor is proportional to the absolute value of the input voltage difference between the bipolar input terminals. A third differential amplifier has its plus input terminal connected to the load resistor. A second gain determining resistor is connected between the minus input of the third differential amplifier and a voltage source. A third FET has its gate connected to the output of the third amplifier. The source and drain circuit of the third transistor is connected between the minus input of the third amplifier and a voltage-frequency converter, constituting an output device. A polarity detector is also provided, comprising a pair of transistors having their inputs connected to the outputs of the first and second differential amplifiers. The outputs of the polarity detector are connected to gates which switch the output of the voltage-frequency converter between up and down counting outputs.

  3. Experimental determination of resonant frequencies by transient scattering from conducting spheres and cylinders

    NASA Astrophysics Data System (ADS)

    Tseng, F.-I.; Sarkar, T. K.

    1984-09-01

    A new experimental technique to measure resonant frequencies of a target is presented. A Tektronix WP 1310 waveform processing system has been employed, which features signal processing software with extensive control over instruments, waveform manipulations, and graphic display. Numerous transient waveforms scattered from spheres and cylinders of various sizes have been recorded. A recently developed data-processing technique has been described and applied to these transient waveforms to extract their resonant frequencies. With the use of a new window designed to have a low near-sidelobe level, the modified fast Fourier transform (FFT) is shown to be able to improve the measurement capability of the system.

  4. [Determination of electron density in atmospheric pressure radio frequency dielectric barrier discharges by Stark broadening].

    PubMed

    Li, Sen; Liu, Zhong-wei; Chen, Qiang; Liu, Fu-ping; Wang, Zheng-duo; Yang, Li-zhen

    2012-01-01

    The use of high frequency power to generate plasma at atmospheric pressure is a relatively new development. An apparatus of atmospheric pressure radio frequency dielectric barrier discharge was constructed. Plasma emission based measurement of electron density in discharge columns from Stark broadening Ar is discribed. The spacial profile of electron density was studied. In the middle of the discharge column, as the input power increases from 138 to 248 W, the electron density rises from 4.038 x 10(21) m(-3) to 4.75 x 10(21) m(-3). PMID:22497121

  5. Determination of High-Frequency Current Distribution Using EMTP-Based Transmission Line Models with Resulting Radiated Electromagnetic Fields

    SciTech Connect

    Mork, B; Nelson, R; Kirkendall, B; Stenvig, N

    2009-11-30

    Application of BPL technologies to existing overhead high-voltage power lines would benefit greatly from improved simulation tools capable of predicting performance - such as the electromagnetic fields radiated from such lines. Existing EMTP-based frequency-dependent line models are attractive since their parameters are derived from physical design dimensions which are easily obtained. However, to calculate the radiated electromagnetic fields, detailed current distributions need to be determined. This paper presents a method of using EMTP line models to determine the current distribution on the lines, as well as a technique for using these current distributions to determine the radiated electromagnetic fields.

  6. Absolute and relative dosimetry for ELIMED

    SciTech Connect

    Cirrone, G. A. P.; Schillaci, F.; Scuderi, V.; Cuttone, G.; Candiano, G.; Musumarra, A.; Pisciotta, P.; Romano, F.; Carpinelli, M.; Presti, D. Lo; Raffaele, L.; Tramontana, A.; Cirio, R.; Sacchi, R.; Monaco, V.; Marchetto, F.; Giordanengo, S.

    2013-07-26

    The definition of detectors, methods and procedures for the absolute and relative dosimetry of laser-driven proton beams is a crucial step toward the clinical use of this new kind of beams. Hence, one of the ELIMED task, will be the definition of procedures aiming to obtain an absolute dose measure at the end of the transport beamline with an accuracy as close as possible to the one required for clinical applications (i.e. of the order of 5% or less). Relative dosimetry procedures must be established, as well: they are necessary in order to determine and verify the beam dose distributions and to monitor the beam fluence and the energetic spectra during irradiations. Radiochromic films, CR39, Faraday Cup, Secondary Emission Monitor (SEM) and transmission ionization chamber will be considered, designed and studied in order to perform a fully dosimetric characterization of the ELIMED proton beam.

  7. Absolute radiometry and the solar constant

    NASA Technical Reports Server (NTRS)

    Willson, R. C.

    1974-01-01

    A series of active cavity radiometers (ACRs) are described which have been developed as standard detectors for the accurate measurement of irradiance in absolute units. It is noted that the ACR is an electrical substitution calorimeter, is designed for automatic remote operation in any environment, and can make irradiance measurements in the range from low-level IR fluxes up to 30 solar constants with small absolute uncertainty. The instrument operates in a differential mode by chopping the radiant flux to be measured at a slow rate, and irradiance is determined from two electrical power measurements together with the instrumental constant. Results are reported for measurements of the solar constant with two types of ACRs. The more accurate measurement yielded a value of 136.6 plus or minus 0.7 mW/sq cm (1.958 plus or minus 0.010 cal/sq cm per min).

  8. Absolute calibration of TFTR helium proportional counters

    SciTech Connect

    Strachan, J.D.; Diesso, M.; Jassby, D.; Johnson, L.; McCauley, S.; Munsat, T.; Roquemore, A.L.; Barnes, C.W. |; Loughlin, M. |

    1995-06-01

    The TFTR helium proportional counters are located in the central five (5) channels of the TFTR multichannel neutron collimator. These detectors were absolutely calibrated using a 14 MeV neutron generator positioned at the horizontal midplane of the TFTR vacuum vessel. The neutron generator position was scanned in centimeter steps to determine the collimator aperture width to 14 MeV neutrons and the absolute sensitivity of each channel. Neutron profiles were measured for TFTR plasmas with time resolution between 5 msec and 50 msec depending upon count rates. The He detectors were used to measure the burnup of 1 MeV tritons in deuterium plasmas, the transport of tritium in trace tritium experiments, and the residual tritium levels in plasmas following 50:50 DT experiments.

  9. Determining radio frequency heating uniformity of mixed beans during disinfestation treatments

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Since chickpeas and lentils are difficulty to artificially infest with live insects for radio frequency (RF) treatment validation, black-eyed peas and mung beans were selected to infest with insects before mixing with chickpeas and lentils. Temperature difference between black-eyed pea and chickpea ...

  10. Determining radio frequency heating uniformity of mixed beans for disinfestation treatments

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Chickpeas and lentils are two important legumes grown in the US and need phytosanitary treatments before exportation, but it is difficult to artificially infest them with live cowpea weevil for radio frequency (RF) treatment validation. To evaluate the more readily infested black-eyed peas and mung ...

  11. Disturbance Frequency Determines Morphology and Community Development in Multi-Species Biofilm at the Landscape Scale

    PubMed Central

    Milferstedt, Kim; Santa-Catalina, Gaëlle; Godon, Jean-Jacques; Escudié, Renaud; Bernet, Nicolas

    2013-01-01

    Many natural and engineered biofilm systems periodically face disturbances. Here we present how the recovery time of a biofilm between disturbances (expressed as disturbance frequency) shapes the development of morphology and community structure in a multi-species biofilm at the landscape scale. It was hypothesized that a high disturbance frequency favors the development of a stable adapted biofilm system while a low disturbance frequency promotes a dynamic biofilm response. Biofilms were grown in laboratory-scale reactors over a period of 55-70 days and exposed to the biocide monochloramine at two frequencies: daily or weekly pulse injections. One untreated reactor served as control. Biofilm morphology and community structure were followed on comparably large biofilm areas at the landscape scale using automated image analysis (spatial gray level dependence matrices) and community fingerprinting (single-strand conformation polymorphisms). We demonstrated that a weekly disturbed biofilm developed a resilient morphology and community structure. Immediately after the disturbance, the biofilm simplified but recovered its initial complex morphology and community structure between two biocide pulses. In the daily treated reactor, one organism largely dominated a morphologically simple and stable biofilm. Disturbances primarily affected the abundance distribution of already present bacterial taxa but did not promote growth of previously undetected organisms. Our work indicates that disturbances can be used as lever to engineer biofilms by maintaining a biofilm between two developmental states. PMID:24303024

  12. Ethylmethanesulfonate Saturation Mutagenesis in Arabidopsis to Determine Frequency of Herbicide Resistance

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Plant resistance to glyphosate has been reported far less frequently than resistance to sulfonylurea and imidazolinone herbicides. However, these studies tend to be anecdotal, without side by side comparisons for a single species or natural isolate. In this study, we tested the frequencies of resist...

  13. Learning in the temporal bisection task: Relative or absolute?

    PubMed

    de Carvalho, Marilia Pinheiro; Machado, Armando; Tonneau, François

    2016-01-01

    We examined whether temporal learning in a bisection task is absolute or relational. Eight pigeons learned to choose a red key after a t-seconds sample and a green key after a 3t-seconds sample. To determine whether they had learned a relative mapping (short→Red, long→Green) or an absolute mapping (t-seconds→Red, 3t-seconds→Green), the pigeons then learned a series of new discriminations in which either the relative or the absolute mapping was maintained. Results showed that the generalization gradient obtained at the end of a discrimination predicted the pattern of choices made during the first session of a new discrimination. Moreover, most acquisition curves and generalization gradients were consistent with the predictions of the learning-to-time model, a Spencean model that instantiates absolute learning with temporal generalization. In the bisection task, the basis of temporal discrimination seems to be absolute, not relational. PMID:26752233

  14. Quantitative determination of mass-resolved ion densities in H{sub 2}-Ar inductively coupled radio frequency plasmas

    SciTech Connect

    Sode, M.; Schwarz-Selinger, T.; Jacob, W.

    2013-03-07

    Inductively coupled H{sub 2}-Ar plasmas are characterized by an energy-dispersive mass spectrometer (plasma monitor), a retarding field analyzer, optical emission spectroscopy, and a Langmuir probe. A procedure is presented that allows determining quantitatively the absolute ion densities of Ar{sup +}, H{sup +}, H{sub 2}{sup +}, H{sub 3}{sup +}, and ArH{sup +} from the plasma monitor raw signals. The calibration procedure considers the energy and mass-dependent transmission of the plasma monitor. It is shown that an additional diagnostic like a Langmuir probe or a retarding field analyzer is necessary to derive absolute fluxes with the plasma monitor. The conversion from fluxes into densities is based on a sheath and density profile model. Measurements were conducted for a total gas pressure of 1.0 Pa. For pure H{sub 2} plasmas, the dominant ion is H{sub 3}{sup +}. For mixed H{sub 2}-Ar plasmas, the ArH{sup +} molecular ion is the most dominant ion species in a wide parameter range. The electron density, n{sub e}, is around 3 Multiplication-Sign 10{sup 16} m{sup -3} and the electron temperature, T{sub e}, decreases from 5 to 3 eV with increasing Ar content. The dissociation degree was measured by actinometry. It is around 1.7% nearly independent on Ar content. The gas temperature, estimated by the rotational distribution of the Q-branch lines of the H{sub 2} Fulcher-{alpha} diagonal band (v Prime =v Double-Prime =2) is estimated to (540 {+-} 50) K.

  15. Laser Frequency Comb Supported Stellar Radial Velocity Determination in the NIR: Initial Results.

    NASA Astrophysics Data System (ADS)

    Osterman, Steve; Diddams, S.; Quinlan, F.; Ycas, G.; Mahadevan, S.; Ramsey, L.; Bender, C.; Terrien, R.; Botzer, B.; Redman, S.

    2011-09-01

    The laser frequency comb presents the potential for a revolutionary increase in radial velocity precision by providing a calibration reference of unprecedented quality in terms of wavelength knowledge, repeatability, number, density and regularity of lines. Promising first steps have been taken leading to the derivation of stellar radial velocities in the NIR H band, a wavelength range well suited to the observation of M dwarfs. These stars, with low mass and low luminosity, are the most prevalent class of stars within 10 parsecs and can be expected to yield a higher reflex velocity for a terrestrial mass planet in the liquid water habitable zone than would be the case with a more massive star such as our own. We present the design and both laboratory and on-sky performance of an H-band laser frequency comb used in conjunction with the Penn State Pathfinder testbed spectrograph and discuss lessons learned and plans for follow on testing.

  16. Effects of the 1993 flood on the determination of flood magnitude and frequency in Iowa

    USGS Publications Warehouse

    Eash, David A.

    1997-01-01

    Several factors, which included recurrence intervals for the 1993 peak discharges and the effective record lengths for 1993, were investigated for the 62 selected streamflow-gaging stations to evaluate their possible effect on the computed flood-frequency discharges. The combined effect of these two factors on the computed 100-year recurrence-interval discharges was significant. Gaging stations were grouped into four discrete categories on the basis ofrecurrence intervals for the 1993 peak discharges and the effective record lengths for 1993 . Of the 28 gaging stations that had small flood magnitudes in 1993 and long record lengths, the difference between the 1992 and the 1993 flood-frequency analyses for 100- year recurrence-interval discharges at 22 gaging stations was less than 5 percent. Of the 10 gaging stations that had large flood magnitudes in 1993 and short record lengths, the increase in 100-year recurrence-interval discharges at 9 gaging stations was greater than 15 percent.

  17. Determination of the Allelic Frequency in Smith-Lemli-Opitz Syndrome by Analysis of Massively Parallel Sequencing Data Sets

    PubMed Central

    Cross, Joanna L.; Iben, James; Simpson, Claire; Thurm, Audrey; Swedo, Susan; Tierney, Elaine; Bailey-Wilson, Joan; Biesecker, Leslie G.; Porter, Forbes D.; Wassif, Christopher A.

    2014-01-01

    Data from massively parallel sequencing or “Next Generation Sequencing” of the human exome has reached a critical mass in both public and private databases, in that these collections now allow researchers to critically evaluate population genetics in a manner that was not feasible a decade ago. The ability to determine pathogenic allele frequencies by evaluation of the full coding sequences and not merely a single SNP or series of SNPs will lead to more accurate estimations of incidence. For demonstrative purposes we analyzed the causative gene for the disorder Smith-Lemli-Opitz Syndrome (SLOS), the 7-dehydrocholesterol reductase (DHCR7) gene and determined both the carrier frequency for DHCR7 mutations, and predicted an expected incidence of the disorder. Estimations of the incidence of SLOS have ranged widely from 1:10,000 to 1:70,000 while the carrier frequency has been reported as high as 1 in 30. Using four exome data sets with a total of 17,836 chromosomes, we ascertained a carrier frequency of pathogenic DHRC7 mutations of 1.01%, and predict a SLOS disease incidence of 1/39,215 conceptions. This approach highlights yet another valuable aspect of the exome sequencing databases, to inform clinical and health policy decisions related to genetic counseling, prenatal testing and newborn screening. PMID:24813812

  18. Determination of the allelic frequency in Smith-Lemli-Opitz syndrome by analysis of massively parallel sequencing data sets.

    PubMed

    Cross, J L; Iben, J; Simpson, C L; Thurm, A; Swedo, S; Tierney, E; Bailey-Wilson, J E; Biesecker, L G; Porter, F D; Wassif, C A

    2015-06-01

    Data from massively parallel sequencing or 'Next Generation Sequencing' of the human exome has reached a critical mass in both public and private databases, in that these collections now allow researchers to critically evaluate population genetics in a manner that was not feasible a decade ago. The ability to determine pathogenic allele frequencies by evaluation of the full coding sequences and not merely a single nucleotide polymorphism (SNP) or series of SNPs will lead to more accurate estimations of incidence. For demonstrative purposes, we analyzed the causative gene for the disorder Smith-Lemli-Opitz Syndrome (SLOS), the 7-dehydrocholesterol reductase (DHCR7) gene and determined both the carrier frequency for DHCR7 mutations, and predicted an expected incidence of the disorder. Estimations of the incidence of SLOS have ranged widely from 1:10,000 to 1:70,000 while the carrier frequency has been reported as high as 1 in 30. Using four exome data sets with a total of 17,836 chromosomes, we ascertained a carrier frequency of pathogenic DHRC7 mutations of 1.01%, and predict a SLOS disease incidence of 1/39,215 conceptions. This approach highlights yet another valuable aspect of the exome sequencing databases, to inform clinical and health policy decisions related to genetic counseling, prenatal testing and newborn screening. PMID:24813812

  19. Short-amplitude high-frequency wing strokes determine the aerodynamics of honeybee flight.

    PubMed

    Altshuler, Douglas L; Dickson, William B; Vance, Jason T; Roberts, Stephen P; Dickinson, Michael H

    2005-12-13

    Most insects are thought to fly by creating a leading-edge vortex that remains attached to the wing as it translates through a stroke. In the species examined so far, stroke amplitude is large, and most of the aerodynamic force is produced halfway through a stroke when translation velocities are highest. Here we demonstrate that honeybees use an alternative strategy, hovering with relatively low stroke amplitude (approximately 90 degrees) and high wingbeat frequency (approximately 230 Hz). When measured on a dynamically scaled robot, the kinematics of honeybee wings generate prominent force peaks during the beginning, middle, and end of each stroke, indicating the importance of additional unsteady mechanisms at stroke reversal. When challenged to fly in low-density heliox, bees responded by maintaining nearly constant wingbeat frequency while increasing stroke amplitude by nearly 50%. We examined the aerodynamic consequences of this change in wing motion by using artificial kinematic patterns in which amplitude was systematically increased in 5 degrees increments. To separate the aerodynamic effects of stroke velocity from those due to amplitude, we performed this analysis under both constant frequency and constant velocity conditions. The results indicate that unsteady forces during stroke reversal make a large contribution to net upward force during hovering but play a diminished role as the animal increases stroke amplitude and flight power. We suggest that the peculiar kinematics of bees may reflect either a specialization for increasing load capacity or a physiological limitation of their flight muscles. PMID:16330767

  20. Spectroscopic pulsational frequency identification and mode determination of γ Doradus star HD 12901

    NASA Astrophysics Data System (ADS)

    Brunsden, E.; Pollard, K. R.; Cottrell, P. L.; Wright, D. J.; De Cat, P.

    2012-12-01

    Using multisite spectroscopic data collected from three sites, the frequencies and pulsational modes of the γ Doradus star HD 12901 were identified. A total of six frequencies in the range 1-2 d-1 were observed, their identifications supported by multiple line-profile measurement techniques and previously published photometry. Five frequencies were of sufficient signal-to-noise ratio for mode identification, and all five displayed similar three-bump standard deviation profiles which were fitted well with (l,m) = (1,1) modes. These fits had reduced χ2 values of less than 18. We propose that this star is an excellent candidate to test models of non-radially pulsating γ Doradus stars as a result of the presence of multiple (1,1) modes. This paper includes data taken at the Mount John University Observatory of the University of Canterbury (New Zealand), the McDonald Observatory of the University of Texas at Austin (Texas, USA) and the European Southern Observatory at La Silla (Chile).

  1. Modelling and measurement of the absolute level of power radiated by antenna integrated THz UTC photodiodes.

    PubMed

    Natrella, Michele; Liu, Chin-Pang; Graham, Chris; van Dijk, Frederic; Liu, Huiyun; Renaud, Cyril C; Seeds, Alwyn J

    2016-05-30

    We determine the output impedance of uni-travelling carrier (UTC) photodiodes at frequencies up to 400 GHz by performing, for the first time, 3D full-wave modelling of detailed UTC photodiode structures. In addition, we demonstrate the importance of the UTC impedance evaluation, by using it in the prediction of the absolute power radiated by an antenna integrated UTC, over a broad frequency range and confirming the predictions by experimental measurements up to 185 GHz. This is done by means of 3D full-wave modelling and is only possible since the source (UTC) to antenna impedance match is properly taken into account. We also show that, when the UTC-to-antenna coupling efficiency is modelled using the classical junction-capacitance/series-resistance concept, calculated and measured levels of absolute radiated power are in substantial disagreement, and the maximum radiated power is overestimated by a factor of almost 7 dB. The ability to calculate the absolute emitted power correctly enables the radiated power to be maximised through optimisation of the UTC-to-antenna impedance match. PMID:27410104

  2. Absolute transition probabilities of phosphorus.

    NASA Technical Reports Server (NTRS)

    Miller, M. H.; Roig, R. A.; Bengtson, R. D.

    1971-01-01

    Use of a gas-driven shock tube to measure the absolute strengths of 21 P I lines and 126 P II lines (from 3300 to 6900 A). Accuracy for prominent, isolated neutral and ionic lines is estimated to be 28 to 40% and 18 to 30%, respectively. The data and the corresponding theoretical predictions are examined for conformity with the sum rules.-

  3. Matrix method of determining the longitudinal-stability coefficients and frequency response of an aircraft from transient flight data

    NASA Technical Reports Server (NTRS)

    Donegan, James J; Pearson, Henry A

    1952-01-01

    A matrix method is presented for determining the longitudinal-stability coefficients and frequency response of an aircraft from arbitrary maneuvers. The method is devised so that it can be applied to time-history measurements of combinations of such simple quantities as angle of attack, pitching velocity, load factor, elevator angle, and hinge moment to obtain the over-all coefficients. Although the method has been devised primarily for the evaluation of stability coefficients which are of primary interest in most aircraft loads and stability studies, it can be used also, with a simple additional computation, to determine the frequency-response characteristics. The entire procedure can be applied or extended to other problems which can be expressed by linear differential equations.

  4. Full Vector Analyses of Cryptochron C2r.2r-l (ca. 2.42-2.44 Ma) Recorded on Koolau Volcano at Halawa, Oahu, Hawaii: Evidence From Directions, Absolute Paleointensity Determinations and 40Ar/39Ar Studies.

    NASA Astrophysics Data System (ADS)

    Browne, E. J.; Herrero-Bervera, E.; Singer, B.

    2005-12-01

    New paleomagnetic measurements (directions and paleointensity determinations), coupled with precise 40Ar/39Ar radioisotopic dating, are revolutionizing our understanding of the geodynamo by providing detailed terrestrial lava records of the short-term behavior of the paleomagnetic field. As part of an investigation of the evolution of Koolau Volcano (one of the volcanoes comprising Oahu Island) and the short-term behavior of the geomagnetic field, we have sampled a long volcanic section located on the buttressed flank of the volcano within Halawa Valley. Prior paleomagnetic and K-Ar investigations of the Koolau (Volcano) Series revealed excursional directions (Site F of Doell and Dalrymple, 1973). The alkaline composition of lava flows, easy access, and close geographical proximity to K-Ar dated lava flows made this newly studied 120 m thick sequence of flows in Halawa valley an excellent candidate for detailed paleomagnetic analysis. At least eight samples collected from each of 28 successive flow-sites were stepwise demagnetized by both alternating field (5mT to 100mT) and thermal (from 28o C to 575-650oC) methods, and the mean directions obtained by principal component analysis. All samples yielded a strong and stable ChRM trending towards the origin based on no less than seven to nine steps, with thermal and AF results agreeing to a very high degree. Low field susceptibility versus temperature (k-T) analyses were conducted for individual lava flows, and the majority of them show reversible curves. Curie point determinations revealed a temperature close to or equal to 580oC, indicative of almost pure magnetite for most of the flows. Magnetic grain sizes analysis indicated SD-PSD sizes. The mean directions of magnetization of the entire section sampled indicate that about 10 m of the section are characterized by excursional directions (5 lava flows). In addition to the directional analyses we performed absolute paleointensity determinations on the 28 lavas

  5. Method and apparatus for determining shaliness and oil saturations in earth formations using induced polarization in the frequency domain

    SciTech Connect

    Vinegar, H.J.; Waxman, M.H.

    1982-11-16

    An apparatus is disclosed for borehole measurements of the induced polarization of earth formations. The apparatus consists of an induced polarization logger capable of measuring both in-phase and quadrature conductivities in the frequency domain. A method is described which uses these measurements to determine cation exchange capacity per unit pore volume, Qv, brine conductivity, Cw, and oil and water saturations, So and Sw, in shaly sands.

  6. Determining the von Mises stress power spectral density for frequency domain fatigue analysis including out-of-phase stress components

    NASA Astrophysics Data System (ADS)

    Bonte, M. H. A.; de Boer, A.; Liebregts, R.

    2007-04-01

    This paper provides a new formula to take into account phase differences in the determination of an equivalent von Mises stress power spectral density (PSD) from multiple random inputs. The obtained von Mises PSD can subsequently be used for fatigue analysis. The formula was derived for use in the commercial vehicle business and was implemented in combination with Finite Element software to predict and analyse fatigue failure in the frequency domain.

  7. In vivo determination of the frequency response of the tooth root canal impedance versus distance from the apical foramen.

    PubMed

    Rambo, Marcos V H; Gamba, Humberto R; Ratzke, Alexandre S; Schneider, Fabio K; Maia, Joaquim M; Ramos, Carlos A S

    2007-01-01

    Working length (WL) determination is a key factor to the endodontic therapy or root canal treatment success. Almost all therapy procedures depend on this measure and the wrong WL determination may produce severe consequences, like post-therapeutic pain and the need of a new root canal treatment. Electronic foramen locators (EFL) have been replacing the traditional radiographic imaging as they are faster, easier to use and have a higher success rate when measuring WL. EFLs are based on the root canal impedance assessment between two electrodes: one fixed on the endodontic file that is inserted into the root canal, and the other positioned at oral mucosa membrane. There are only few reported studies that qualify or quantify the root canal impedance characteristics. The present work aims to determine the module of tooth root canal frequency response. The preliminary results show the frequency response module variation as a function of endodontic file position inside the root canal and reinforce the methods based on relative impedance over frequency analysis used in modern EFLs. PMID:18002020

  8. Blood pressure targets and absolute cardiovascular risk.

    PubMed

    Odutayo, Ayodele; Rahimi, Kazem; Hsiao, Allan J; Emdin, Connor A

    2015-08-01

    In the Eighth Joint National Committee guideline on hypertension, the threshold for the initiation of blood pressure-lowering treatment for elderly adults (≥60 years) without chronic kidney disease or diabetes mellitus was raised from 140/90 mm Hg to 150/90 mm Hg. However, the committee was not unanimous in this decision, particularly because a large proportion of adults ≥60 years may be at high cardiovascular risk. On the basis of Eighth Joint National Committee guideline, we sought to determine the absolute 10-year risk of cardiovascular disease among these adults through analyzing the National Health and Nutrition Examination Survey (2005-2012). The primary outcome measure was the proportion of adults who were at ≥20% predicted absolute cardiovascular risk and above goals for the Seventh Joint National Committee guideline but reclassified as at target under the Eighth Joint National Committee guideline (reclassified). The Framingham General Cardiovascular Disease Risk Score was used. From 2005 to 2012, the surveys included 12 963 adults aged 30 to 74 years with blood pressure measurements, of which 914 were reclassified based on the guideline. Among individuals reclassified as not in need of additional treatment, the proportion of adults 60 to 74 years without chronic kidney disease or diabetes mellitus at ≥20% absolute risk was 44.8%. This corresponds to 0.8 million adults. The proportion at high cardiovascular risk remained sizable among adults who were not receiving blood pressure-lowering treatment. Taken together, a sizable proportion of reclassified adults 60 to 74 years without chronic kidney disease or diabetes mellitus was at ≥20% absolute cardiovascular risk. PMID:26056340

  9. What Personal and Environmental Factors Determine Frequency of Urban Greenspace Use?

    PubMed Central

    Dallimer, Martin; Davies, Zoe G.; Irvine, Katherine N.; Maltby, Lorraine; Warren, Philip H.; Gaston, Kevin J.; Armsworth, Paul R.

    2014-01-01

    For many people, urban greenspaces are the only places where they encounter the natural world. This is concerning as there is growing evidence demonstrating that human well-being is enhanced by exposure to nature. There is, therefore, a compelling argument to increase how frequently people use urban greenspaces. This may be achieved in two complementary ways by encouraging: (I) non-users to start visiting urban greenspaces; (II) existing users to visit more often. Here we examine the factors that influence frequency of greenspace visitation in the city of Sheffield, England. We demonstrate that people who visit a site least frequently state lower self-reported psychological well-being. We hypothesised that a combination of socio-demographic characteristics of the participants, and the biophysical attributes of the greenspaces that they were visiting, would be important in influencing visit frequency. However, socio-demographic characteristics (income, age, gender) were not found to be predictors. In contrast, some biophysical attributes of greenspaces were significantly related to use frequency. Frequent use was more likely when the time taken to reach a greenspace was shorter and for sites with a higher index of greenspace neglect, but were unrelated to tree cover or bird species richness. We related these results to the motivations that people provide for their visits. Infrequent users were more likely to state motivations associated with the quality of the space, while frequent users gave motivations pertaining to physical, repeated activities. This suggests that there may be no simple way to manage greenspaces to maximise their use across user cohorts as the motivations for visits are very different. PMID:25105548

  10. Determination of charge carrier transport in radio frequency plasma polymerized aniline thin films

    NASA Astrophysics Data System (ADS)

    Sivaraman, Sajeev; Anantharaman, M. R.

    2010-02-01

    The carrier transport mechanism of polyaniline (PA) thin films prepared by radio frequency plasma polymerization is described in this paper. The mechanism of electrical conduction and carrier mobility of PA thin films for different temperatures were examined using the aluminium-PA-aluminium (Al-PA-Al) structure. It is found that the mechanism of carrier transport in these thin films is space charge limited conduction. J-V studies on an asymmetric electrode configuration using indium tin oxide (ITO) as the base electrode and Al as the upper electrode (ITO-PA-Al structure) show a diode-like behaviour with a considerable rectification ratio.

  11. Determination of plasma frequency, damping constant, and size distribution from the complex dielectric function of noble metal nanoparticles

    NASA Astrophysics Data System (ADS)

    Mendoza Herrera, Luis J.; Arboleda, David Muñetón; Schinca, Daniel C.; Scaffardi, Lucía B.

    2014-12-01

    This paper develops a novel method for simultaneously determining the plasma frequency ωP and the damping constant γfr e e in the bulk damped oscillator Drude model, based on experimentally measured real and imaginary parts of the metal refractive index in the IR wavelength range, lifting the usual approximation that restricts frequency values to the UV-deep UV region. Our method was applied to gold, silver, and copper, improving the relative uncertainties in the final values for ωp (0.5%-1.6%) and for γfr e e (3%-8%), which are smaller than those reported in the literature. These small uncertainties in ωp and γfr e e determination yield a much better fit of the experimental complex dielectric function. For the case of nanoparticles (Nps), a series expansion of the Drude expression (which includes ωp and γfr e e determined using our method) enables size-dependent dielectric function to be written as the sum of three terms: the experimental bulk dielectric function plus two size corrective terms, one for free electron, and the other for bound-electron contributions. Finally, size distribution of nanometric and subnanometric gold Nps in colloidal suspension was determined through fitting its experimental optical extinction spectrum using Mie theory based on the previously determined dielectric function. Results are compared with size histogram obtained from Transmission Electron Microscopy (TEM).

  12. Determination of plasma frequency, damping constant, and size distribution from the complex dielectric function of noble metal nanoparticles

    SciTech Connect

    Mendoza Herrera, Luis J.; Arboleda, David Muñetón; Schinca, Daniel C.; Scaffardi, Lucía B.

    2014-12-21

    This paper develops a novel method for simultaneously determining the plasma frequency ω{sub P}   and the damping constant γ{sub free} in the bulk damped oscillator Drude model, based on experimentally measured real and imaginary parts of the metal refractive index in the IR wavelength range, lifting the usual approximation that restricts frequency values to the UV-deep UV region. Our method was applied to gold, silver, and copper, improving the relative uncertainties in the final values for ω{sub p} (0.5%–1.6%) and for γ{sub free} (3%–8%), which are smaller than those reported in the literature. These small uncertainties in ω{sub p} and γ{sub free} determination yield a much better fit of the experimental complex dielectric function. For the case of nanoparticles (Nps), a series expansion of the Drude expression (which includes ω{sub p} and γ{sub free} determined using our method) enables size-dependent dielectric function to be written as the sum of three terms: the experimental bulk dielectric function plus two size corrective terms, one for free electron, and the other for bound-electron contributions. Finally, size distribution of nanometric and subnanometric gold Nps in colloidal suspension was determined through fitting its experimental optical extinction spectrum using Mie theory based on the previously determined dielectric function. Results are compared with size histogram obtained from Transmission Electron Microscopy (TEM)

  13. The frequency and duration of Salmonella-macrophage adhesion events determines infection efficiency.

    PubMed

    Achouri, Sarra; Wright, John A; Evans, Lewis; Macleod, Charlotte; Fraser, Gillian; Cicuta, Pietro; Bryant, Clare E

    2015-02-01

    Salmonella enterica causes a range of important diseases in humans and a in a variety of animal species. The ability of bacteria to adhere to, invade and survive within host cells plays an important role in the pathogenesis of Salmonella infections. In systemic salmonellosis, macrophages constitute a niche for the proliferation of bacteria within the host organism. Salmonella enterica serovar Typhimurium is flagellated and the frequency with which this bacterium collides with a cell is important for infection efficiency. We investigated how bacterial motility affects infection efficiency, using a combination of population-level macrophage infection experiments and direct imaging of single-cell infection events, comparing wild-type and motility mutants. Non-motile and aflagellate bacterial strains, in contrast to wild-type bacteria, collide less frequently with macrophages, are in contact with the cell for less time and infect less frequently. Run-biased Salmonella also collide less frequently with macrophages but maintain contact with macrophages for a longer period of time than wild-type strains and infect the cells more readily. Our results suggest that uptake of S. Typhimurium by macrophages is dependent upon the duration of contact time of the bacterium with the cell, in addition to the frequency with which the bacteria collide with the cell. PMID:25533091

  14. Correlating absolute concentrations of gas-phase species determined by microwave, Fourier transform infrared, and atomic absorption spectroscopies to properties of silicon dioxide films deposited in an electron cyclotron resonance reactor

    NASA Astrophysics Data System (ADS)

    Cornett, Mary Jezl

    Three different gas-phase absorption spectroscopies (microwave, FTIR, and silicon atomic absorption) were used simultaneously during the plasma enhanced chemical vapor deposition of SiO2 and fluorinated SiO 2 films using an ECR deposition reactor. With these spectroscopic techniques, absolute concentrations of a large number of species present in these deposition plasmas were determined. A new ECR system with multiple diagnostic ports on the same horizontal plane, and incorporating an electrostatic chuck, rf-bias, and He-backside cooling, was constructed to facilitate these studies. Correlations to the quality of the resulting films were made using ellipsometry, FTIR, XPS, and wet etch rate techniques. The systems investigated were SiH 4/O2/Ar, SiH4/SiF4/O2 and TEOS/O2 plasmas. The SiH4/O2 plasmas are found to contain less water than previously expected (under our detection limit of 0.1 mTorr). The molecular fragment SiO was monitored as a function of power, pressure, oxygen flow, and argon flow at densities between 3.7 × 109 and 1.3 × 10-11 cm-3 in this system. Silicon atoms were detected at densities between 5.1 × 109 and 5.8 × 1010 cm -3. The decomposition of SiF4 is investigated and is shown to occur at a constant rate of about 98% in pure SiF4/O 2 plasmas. This dissociation rate is enhanced when silane is added. Water and HF are generated in large quantities when SiH4 and SiF 4 are both present in the system, and reach their maximum concentrations at the SiF4/SiH4 ratio where the film quality appears to be the best. Fluorine incorporation into SiOF films result in a consistent decrease in index of refraction values. No SiO molecules were detected in SiH4/SiF4/O2 chemistries (<5 × 10 9 cm-3). Plasmas employing TEOS/O2 chemistries show large concentrations of CO, CO2 and H2O. Larger organic molecules (ethanol, acetaldehyde, methanol, formaldehyde, and formic acid) are also present in these plasmas, totaling about 9% of the species present under most

  15. Techniques to Determine Maintenace Frequency of Permeable Pavement Systems with Time Domain Reflectometers (TDRs

    EPA Science Inventory

    As the surface clogs in permeable pavement systems, they lose effectiveness and require maintenance. There is limited direct guidance for determining when maintenance is needed to prevent surface runoff bypass. Research is being conducted using multiple time domain reflectomete...

  16. Determination of cytotoxic T-lymphocyte precursor frequencies using europium labeling as a nonradioactive alternative to labeling with chromium-51.

    PubMed

    Bouma, G J; van der Meer-Prins, P M; van Bree, F P; van Rood, J J; Claas, F H

    1992-10-01

    We report on the use of europium (Eu) as a suitable nonradioactive alternative for target cell labeling in limiting dilution analysis (LDA) assays set up to determine cytotoxic T-lymphocyte precursor (CTLp) frequencies. A nonradioactive alternative to the commonly used chromium-51 (51Cr) release assay seems desirable because working with radioisotopes has some major disadvantages concerning possible health risks, environmental load, costs of facilities necessary for working with radioisotopes, and shelf life. Some groups have successfully applied the Eu release assay based on detection by time-resolved fluorometry, to tests in which NK- or LAK-cell activity or cytotoxic T-lymphocyte reactions were measured. This led to the investigation whether this method could also be applicable to the more specific determination of CTLp frequencies in LDA assays. After optimal labeling conditions had been established, the sensitivity of the Eu release assay was determined by performing several LDA assays in which the target cells were labeled with either Eu or radioactive 51Cr. When CTLp frequencies were compared, it was shown that the Eu release assay is at least as sensitive and specific as the 51Cr release assay. Moreover, although the labeling procedure takes longer, sample processing is much faster: only 1 second per sample. The fact that the Eu release assay is not radioactive enables the assay to be performed at any laboratory and even--because the frequency of CTLps may have implications for organ graft survival and for donor selection in bone marrow transplantation--to do so on a routine basis. PMID:1286979

  17. Absolute and Convective Instability of a Liquid Jet in Microgravity

    NASA Technical Reports Server (NTRS)

    Lin, Sung P.; Vihinen, I.; Honohan, A.; Hudman, Michael D.

    1996-01-01

    The transition from convective to absolute instability is observed in the 2.2 second drop tower of the NASA Lewis Research Center. In convective instability the disturbance grows spatially as it is convected downstream. In absolute instability the disturbance propagates both downstream and upstream, and manifests itself as an expanding sphere. The transition Reynolds numbers are determined for two different Weber numbers by use of Glycerin and a Silicone oil. Preliminary comparisons with theory are made.

  18. Orientation determination of interfacial bent α-helical structures using Sum Frequency Generation vibrational spectroscopy

    NASA Astrophysics Data System (ADS)

    Nguyen, Khoi Tan

    2015-02-01

    Sum Frequency Generation (SFG) has been shown to be a powerful and versatile technique in studies of proteins/peptides at surfaces and interfaces. Recently SFG was successfully applied in studies of interfacial macro-molecules with increasing size and complexity. In this report we continued to employ bond additivity model and group theory to demonstrate the importance of both the inter-helical tilt angle and the lengths of the helical segments assembling the structures being studies. Specifically, a newly improved SFG data analysis of multiple α-helical structures on melittin was used to interpret the SFG experimental observation and also verified the findings with the recent insights brought by other spectroscopic techniques.

  19. Use of low-frequency electrical impedance measurements to determine phospholipid content in amniotic fluid

    NASA Astrophysics Data System (ADS)

    DeLuca, F.; Cametti, C.; Zimatore, G.; Maraviglia, B.; Pachi', A.

    1996-09-01

    In this report we propose a new method for an in vitro test of the foetal lung maturity based on the measurement of the electrical conductivity of the overall amniotic fluid obtained from transabdominal amniocentesis, since this quantity can be linked to a first approximation in a very simple way to the phospholipid content. We have carried out measurements of 85 different samples of amniotic fluid as a function of gestation weeks and we have observed a pronounced change of the electrical conductivity that reflects the increase in the phospholipid concentration occurring at the end of normal pregnancies. The method could be further developed to obtain similar information on in vivo experiments by means of bioelectric impedance tomography, taking advantage of the frequency dependence of the tissue electrical impedance.

  20. The Absolute Spectrum Polarimeter (ASP)

    NASA Technical Reports Server (NTRS)

    Kogut, A. J.

    2010-01-01

    The Absolute Spectrum Polarimeter (ASP) is an Explorer-class mission to map the absolute intensity and linear polarization of the cosmic microwave background and diffuse astrophysical foregrounds over the full sky from 30 GHz to 5 THz. The principal science goal is the detection and characterization of linear polarization from an inflationary epoch in the early universe, with tensor-to-scalar ratio r much greater than 1O(raised to the power of { -3}) and Compton distortion y < 10 (raised to the power of{-6}). We describe the ASP instrument and mission architecture needed to detect the signature of an inflationary epoch in the early universe using only 4 semiconductor bolometers.

  1. Absolute calibration of optical flats

    DOEpatents

    Sommargren, Gary E.

    2005-04-05

    The invention uses the phase shifting diffraction interferometer (PSDI) to provide a true point-by-point measurement of absolute flatness over the surface of optical flats. Beams exiting the fiber optics in a PSDI have perfect spherical wavefronts. The measurement beam is reflected from the optical flat and passed through an auxiliary optic to then be combined with the reference beam on a CCD. The combined beams include phase errors due to both the optic under test and the auxiliary optic. Standard phase extraction algorithms are used to calculate this combined phase error. The optical flat is then removed from the system and the measurement fiber is moved to recombine the two beams. The newly combined beams include only the phase errors due to the auxiliary optic. When the second phase measurement is subtracted from the first phase measurement, the absolute phase error of the optical flat is obtained.

  2. Determinants of tillage frequency among smallholder farmers in two semi-arid areas in Ethiopia

    NASA Astrophysics Data System (ADS)

    Temesgen, Melesse; Rockstrom, J.; Savenije, H. H. G.; Hoogmoed, W. B.; Alemu, Dawit

    Traditional tillage systems practiced by farmers in semi-arid regions of Ethiopia are characterized by repeated and cross plowing with an indigenous plow called Maresha. Repeated and cross plowing have led to land degradation. Conservation tillage systems that advocate minimum soil disturbance can alleviate land degradation problems. However, before introducing reduced tillage systems, it was found necessary to study why farmers undertake repeated plowing. The study was undertaken in two semi-arid areas called Melkawoba and Wulinchity located in the central rift valley of Ethiopia and on two major crops; Tef ( Eragrostis Tef (Zucc.)) and maize ( Zea mays XX). Fifty farmers from each area were randomly selected and interviewed using a structured questionnaire. The results showed that farmers in the study area plow repeatedly in order to completely disturb unplowed strips of land left between adjacent furrows. Unplowed strips are the results of the V-shaped furrows created by the Maresha plow. Farmers generally do not plow before the soil is wetted by rainfall. Wetting and drying cycles due to dry spells occurring between rainfall events force farmers to plow frequently to avoid moisture losses through surface runoff, evaporation and weed transpiration. Tef fields are plowed 4-5 times while maize fields are plowed 3-4 times. Tillage frequency increased with the education level and experience of farmers; with their perception about the purpose of tillage such as moisture conservation, weed control and soil warming; and with resource availability such as area of land and family labor. Tillage frequency was higher for Tef than for maize and in heavy soils than in light soils.

  3. Allelic frequency determination of the 24-bp chitotriosidase duplication in the Portuguese population by real-time PCR.

    PubMed

    Rodrigues, M R; Sá Miranda, M C; Amaral, O

    2004-01-01

    Chitotriosidase is a human chitinase produced by macrophages. Its enzymatic activity is markedly elevated in serum of patients suffering from lysosomal storage disorders, as well as other diseases in which macrophages are activated. Therefore, it is a useful tool as a secondary marker in the diagnosis of several disorders including Gaucher disease type 1 and Niemann-Pick disease. The determination of chitotriosidase levels as a diagnosis complement in some lysosomal storage disorders and in enzyme replacement therapy follow-up of Gaucher disease patients is of great importance. However, the fact that a mutation caused by a 24-bp duplication in the CHIT1 gene resulting in deficiency of plasma chitotriosidase activity is very frequent makes the establishment of the frequency of this mutation in different population groups necessary. Furthermore, in order to validate the use of chitotriosidase activity as a marker, it is indispensable to screen individuals for this particular mutation. In this work, we present the results of a study where the allelic frequency of the above mentioned CHIT1 gene mutation was determined in the Portuguese population by real-time PCR. The frequency of carriers encountered in this sample of Portuguese individuals was of 37%. PMID:15528158

  4. Analytical modeling for the determination of nonlocal resonance frequencies of perforated nanobeams subjected to temperature-induced loads

    NASA Astrophysics Data System (ADS)

    Bourouina, Hicham; Yahiaoui, Réda; Sahar, Abdellah; Benamar, Mohammed El Amine

    2016-01-01

    This paper is concerned with the investigation of thermal loads and small scale effects on free dynamics vibration of slender simply-supported nanobeams perforated with periodic square holes network and subjected to temperature-induced loads. The Euler-Bernoulli beam model (EBM) and shear beam model (SBM) developed for the determination of resonance frequency are derived by modifying the standard Timoshenko beam equations. The small scale effect is included by using the Eringen's nonlocal elasticity theory while the thermal loads effect is included by considering the additional axial thermal force in the standard differential equations. Numerical results are shown that the resonance frequency change, the thermal loads and the small scale effects are depended on size and number of holes. Thus, numerical results are discussed in detail for a properly investigation of the dynamic behavior of perforated nanobeams which are of interest in the development of resonant devices integrated in micro/nanoelectromichanical systems (M(N)EMS).

  5. Fluorescence lifetimes of anthracycline drugs in phospholipid bilayers determined by frequency-domain fluorometry

    NASA Astrophysics Data System (ADS)

    Burke, Thomas G.; Malak, Henryk M.; Doroshow, James H.

    1990-05-01

    Time-resolved fluorescence intensity decay data from anthracycline anticancer drugs present in model membranes were obtained using a gigahertz frequency-domain fluorometer [Lakowicz et al. (1986) Rev. Sci. Instrum. 57, 2499-2506]. Exciting light of 290 nm, modulated at multiple frequencies from 8 MHz to 400 MHz, was used to study the interactions of Adriamycin, daunomycin and related antibiotics with small unilamellar vesicles composed of dimyristoylphosphatidylcholine (DMPC) at 28°C. Fluorescence decay data for drug molecules free in solution as well as bound to membranes were best fit by exponentials requiring two terms rather than by single exponential decays. For example, one-component analysis of the decay data for Adriamycin free in phosphate buffered saline (PBS) solution resulted in a reduced x2 value of 140 ((tau) = 0.88 ns), while a two-component fit resulted in a substantially smaller reduced x2 value of 2.6 ((tau)1 = 1.13 ns, (alpha)1 = 0.60, (tau)2 = 0.30 ns). Upon association with membranes, each of the anthracyclines studied displayed a larger r1 value while the r2 value remained the same or increased (for example, DMPC-bound Adriamycin showed r1 = 1.68 ns , a1 = 0 . 64 , r2 = 0 . 33 ns) . Analyses of the fluorescence emission decays of anthracyclines were also made assuming each decay is composed of a single Lorentzian distribution of lifetimes. Data taken on Adriamycin in PBS, when fit using one continuous component, displayed (tau), (alpha), w, and reduced x2 values of 0.68 ns, 1, 0.60 ns, and 9.1, respectively. The distribution became quite broad upon drug association with membrane (DMPCbound Adriamycin: (tau) = 0.75 ns, (alpha) = 1, w = 2.24 ns, x2 = 13). For each anthracycline studied, continuous component fits showed significant broadening in the distributions upon drug association with membrane. Relatively large shifts in lifetime values were observed for the carminomycin and 4-demethoxydaunomycin analogues upon binding model lipid membranes

  6. Capacitively-Coupled Resistivity measurements to determine frequency dependent electrical parameters in periglacial environment - theoretical considerations and first field tests.

    NASA Astrophysics Data System (ADS)

    Przyklenk, A.; Hördt, A.; Radić, T.

    2016-05-01

    Capacitively-Coupled Resistivity (CCR) is conventionally used to emulate DC resistivity measurements and may provide important information about the ice content of material in periglacial areas. The application of CCR theoretically enables the determination of both electrical parameters, i.e. the resistivity and the electrical permittivity, by analyzing magnitude and phase shift spectra. The electrical permittivity may dominate the impedance, especially in periglacial areas or regions of hydrogeological interest. However, previous theoretical work suggested that the phase shift may strongly depend on electrode height above ground, implying that electrode height must be known with great accuracy to determine electrical permittivity. Here, we demonstrate with laboratory test measurements, theoretical modelling and by analysing the Jacobian matrix of the inversion, that the sensitivity towards electrode height is drastically reduced if the electrical permittivity is frequency dependent in a way that is typical for ice. For the fist time, we used a novel broadband CCR device "Chameleon" for a field test located in one of the ridge galleries beneath the crest of Mount Zugspitze. A permanently ice covered bottom of a tunnel was examined. For the inversion of the measured spectra, the frequency dependance of the electrical parameters was parameterized in 3 different ways. A Debye Model for pure ices, a Cole-Cole Model for pure ices and a dual Cole-Cole Model including interfacial water additionally. The frequency-dependent resistivity and permittivity spectra obtained from the inversion, including low and high frequency limits, agree reasonably well with laboratory and field measurements reported in the literature.

  7. Capacitively-Coupled Resistivity measurements to determine frequency dependent electrical parameters in periglacial environment - theoretical considerations and first field tests

    NASA Astrophysics Data System (ADS)

    Przyklenk, A.; Hördt, A.; Radić, T.

    2016-05-01

    Capacitively-Coupled Resistivity (CCR) is conventionally used to emulate DC resistivity measurements and may provide important information about the ice content of material in periglacial areas. The application of CCR theoretically enables the determination of both electrical parameters, i.e. the resistivity and the electrical permittivity, by analyzing magnitude and phase shift spectra. The electrical permittivity may dominate the impedance, especially in periglacial areas or regions of hydrogeological interest. However, previous theoretical work suggested that the phase shift may strongly depend on electrode height above ground, implying that electrode height must be known with great accuracy to determine electrical permittivity. Here, we demonstrate with laboratory test measurements, theoretical modelling and by analysing the Jacobian matrix of the inversion, that the sensitivity towards electrode height is drastically reduced if the electrical permittivity is frequency dependent in a way that is typical for ice. For the fist time, we used a novel broadband CCR device "Chameleon" for a field test located in one of the ridge galleries beneath the crest of Mount Zugspitze. A permanently ice covered bottom of a tunnel was examined. For the inversion of the measured spectra, the frequency dependance of the electrical parameters was parameterized in 3 different ways. A Debye Model for pure ices, a Cole-Cole Model for pure ices and a dual Cole-Cole Model including interfacial water additionally. The frequency-dependent resistivity and permittivity spectra obtained from the inversion, including low and high frequency limits, agree reasonably well with laboratory and field measurements reported in the literature.

  8. Frequency of Cytotoxic T Lymphocyte Precursors to Herpes Simplex Virus Type 1 as Determined by Limiting Dilution Analysis

    PubMed Central

    Rouse, Barry T.; Larsen, Hal S.; Wagner, Hermann

    1983-01-01

    The conditions for establishing a limiting dilution assay to measure cytotoxic T lymphocyte precursors (CTL-P) against herpes simplex virus type 1 (HSV-1) were determined. Analysis by Poisson statistics demonstrated that the estimated frequency of HSV-1-reactive cells in the spleens of normal mice was less than 1/250,000. In contrast, mice immunized previously with infectious HSV-1 demonstrated a CTL-P frequency between 1/3,500 and 1/15,670. The generation of a maximum cytotoxic T lymphocyte response required that mice be primed in vivo with infectious virus. Immunization with inactivated virus either failed to elicit detectable CTL-P frequencies or gave frequencies markedly less than those induced with infectious virus. To obtain positive cultures, the responder cell population had to be exposed to stimulator splenocytes expressing viral antigens. Normal splenocytes without virus or normal splenocytes with T cell growth factor did not result in significant cytotoxicity. Split culture analysis comparing cytotoxicity against syngeneic and allogeneic virus-infected targets provided evidence for specificity, H-2 restriction, and the T cell nature of the CTL-P. It was determined that precursors were eliminated by treatment with anti-Thy 1, Lyt 2.1, or Lyt 1.1, indicating the CTL-P were Lyt 1+2+ cells. Cytotoxicity was reduced after treatment of the responders with anti-Lyt 2 plus complement, which gave further evidence of the T cell nature of the cytotoxic T lymphocytes. These experiments demonstrated the feasibility of using the limiting dilution approach as a highly sensitive and quantitative means to measure the cell-mediated immune response to HSV-1 antigens. PMID:6299949

  9. Determination of Black Hole Mass in Cyg X-1 by Scaling of Spectral Index-QPO Frequency Correlation

    NASA Technical Reports Server (NTRS)

    Shaposhnikov, Nickolai; Titarchuk, Lev

    2007-01-01

    It is well established that timing and spectral properties of Galactic Black Hole (BH) X-ray binaries (XRB) are strongly correlated. In particular, it has been shown that low frequency Quasi-Periodic Oscillation (QPO) nu(sub low) - photon index GAMMA correlation curves have a specific pattern. In a number of the sources studied the shape of the index-low frequency QPO correlations are self-similar with a position offset in the nu(sub low) - GAMMA plane determined by a BH mass M(sub BH). Specifically, Titarchuk & Fiorito (2004) gave strong theoretical and observational arguments that the QPO frequency values in this nu(sub low) - GAMMA correlation should be inversely proportional to M(sub BH). A simple translation of the correlation for a given source along frequency axis leads to the observed correlation for another source. As a result of this translation one can obtain a scaling factor which is simply a BH mass ratio for these particular sources. This property of the correlations offers a fundamentally new method for BH mass determination in XRBs. Here we use the observed QPO-index correlations observed in three BH sources: GRO J1655-40, GRS 1915+105 and Cyg X-1. The BH mass of (6.3 plus or minus 0.5) solar mass in GRO J1655-40 is obtained using optical observations. RXTE observations during the recent 2005 outburst yielded sufficient data to establish the correlation pattern during both rise and decay of the event. We use GRO J1655-40 as a standard reference source to measure the BH mass in Cyg X-1. We also revisit the GRS 1915+105 data as a further test of our scaling method. We obtain the BH mass in Cyg X-1 in the range 7.6-9.9.

  10. Frequency, determinants and impact of overcrowding in emergency departments in Canada: a national survey.

    PubMed

    Bond, Kenneth; Ospina, Maria B; Blitz, Sandra; Afilalo, Marc; Campbell, Sam G; Bullard, Michael; Innes, Grant; Holroyd, Brian; Curry, Gil; Schull, Michael; Rowe, Brian H

    2007-01-01

    Several reports have documented the prevalence and severity of emergency department (ED) overcrowding at specific hospitals or cities in Canada; however, no study has examined the issue at a national level. A 54-item, self-administered, postal and web-based questionnaire was distributed to 243 ED directors in Canada to collect data on the frequency, impact and factors associated with ED overcrowding. The survey was completed by 158 (65% response rate) ED directors, 62% of whom reported overcrowding as a major or severe problem during the past year. Directors attributed overcrowding to a variety of issues including a lack of admitting beds (85%), lack of acute care beds (74%) and the increased length of stay of admitted patients in the ED (63%). They perceived ED overcrowding to have a major impact on increasing stress among nurses (82%), ED wait times (79%) and the boarding of admitted patients in the ED while waiting for beds (67%). Overcrowding is not limited to large urban centres; nor is it limited to academic and teaching hospitals. The perspective of ED directors reinforces the need for further examination of effective policies and interventions to reduce ED overcrowding. PMID:18019897

  11. How do family physicians communicate about cardiovascular risk? Frequencies and determinants of different communication formats

    PubMed Central

    2011-01-01

    Background Patients understand information about risk better if it is communicated in numerical or visual formats (e.g. graphs) compared to verbal qualifiers only. How frequently different communication formats are used in clinical primary care settings is unknown. Methods We collected socioeconomic and patient understanding data using questionnaires and audio-recorded consultations about cardiovascular disease risk. The frequencies of the communication formats were calculated and multivariate regression analysis of associations between communication formats, patient and general practitioner characteristics, and patient subjective understanding was performed. Results In 73% of 70 consultations, verbal qualifiers were used exclusively to communicate cardiovascular risk, compared to numerical (11%) and visual (16%) formats. Female GPs and female patient's gender were significantly associated with a higher use of verbal formats compared to visual formats (p = 0.001 and p = 0.039, respectively). Patient subjective understanding was significantly higher in visual counseling compared to verbal counseling (p = 0.001). Conclusions Verbal qualifiers are the most often used communication format, though recommendations favor numerical and visual formats, with visual formats resulting in better understanding than others. Also, gender is associated with the choice of communication format. Barriers against numerical and visual communication formats among GPs and patients should be studied, including gender aspects. Adequate risk communication should be integrated into physicians' education. PMID:21466686

  12. A corroborative study on improving pitch determination by time-frequency cepstrum decomposition using wavelets.

    PubMed

    Bahja, Fadoua; Di Martino, Joseph; Ibn Elhaj, Elhassan; Aboutajdine, Driss

    2016-01-01

    A new wavelet-based method is presented in this work for estimating and tracking the pitch period. The main idea of the proposed new approach consists in extracting the cepstrum excitation signal and applying on it a wavelet transform whose resulting approximation coefficients are smoothed, for a better pitch determination. Although the principle of the algorithms proposed has already been considered previously, the novelty of our methods relies in the use of powerful wavelet transforms well adapted to pitch determination. The wavelet transforms considered in this article are the discrete wavelet transform and the dual tree complex wavelet transform. This article, by all the provided experimental results, corroborates the idea of decomposing the cepstrum excitation by using wavelet transforms for improving pitch detection. Another interesting point of this article relies in using a simple but efficient voicing decision (which actually improves a similar voicing criterion we proposed in a preceding published study) which on one hand respects the real-time process with low latency and on the other hand allows obtaining low classifications errors. The accuracy of the proposed pitch tracking algorithms has been evaluated using the international Bagshaw and the Keele databases which include male and female speakers. Our various experimental results demonstrate that the proposed methods provide important performance improvements when compared with previously published pitch determination algorithms. PMID:27213131

  13. Determining Vaccination Frequency in Farmed Rainbow Trout Using Vibrio anguillarum O1 Specific Serum Antibody Measurements

    PubMed Central

    Holten-Andersen, Lars; Dalsgaard, Inger; Nylén, Jørgen; Lorenzen, Niels; Buchmann, Kurt

    2012-01-01

    high vaccination frequencies necessary for optimal protection with a reported effective vaccine. PMID:23185402

  14. Revisiting absolute and relative judgments in the WITNESS model.

    PubMed

    Fife, Dustin; Perry, Colton; Gronlund, Scott D

    2014-04-01

    The WITNESS model (Clark in Applied Cognitive Psychology 17:629-654, 2003) provides a theoretical framework with which to investigate the factors that contribute to eyewitness identification decisions. One key factor involves the contributions of absolute versus relative judgments. An absolute contribution is determined by the degree of match between an individual lineup member and memory for the perpetrator; a relative contribution involves the degree to which the best-matching lineup member is a better match to memory than the remaining lineup members. In WITNESS, the proportional contributions of relative versus absolute judgments are governed by the values of the decision weight parameters. We conducted an exploration of the WITNESS model's parameter space to determine the identifiability of these relative/absolute decision weight parameters, and compared the results to a restricted version of the model that does not vary the decision weight parameters. This exploration revealed that the decision weights in WITNESS are difficult to identify: Data often can be fit equally well by setting the decision weights to nearly any value and compensating with a criterion adjustment. Clark, Erickson, and Breneman (Law and Human Behavior 35:364-380, 2011) claimed to demonstrate a theoretical basis for the superiority of lineup decisions that are based on absolute contributions, but the relationship between the decision weights and the criterion weakens this claim. These findings necessitate reconsidering the role of the relative/absolute judgment distinction in eyewitness decision making. PMID:23943556

  15. Genetically Determined Amerindian Ancestry Correlates with Increased Frequency of Risk Alleles for Systemic Lupus Erythematosus

    PubMed Central

    Sanchez, E; Webb, R; Rasmussen, A.; Kelly, J.A; Riba, L.; Kaufman, K.M.; Garcia-de la Torre, I.; Moctezuma, J.F.; Maradiaga-Ceceña, M.A.; Cardiel, M.; Acevedo, E.; Cucho-Venegas, M.; Garcia, M.A.; Gamron, S.; Pons-Estel, B.A.; Vasconcelos, C.; Martin, J.; Tusié-Luna, T.; Harley, J.B.; Richardson, B.; Sawalha, A.H.; Alarcón-Riquelme, M.E.

    2011-01-01

    Objectives To analyze if genetically determined Amerindian ancestry predicts the increased presence of risk alleles of known susceptibility genes for systemic lupus erythematosus. Methods Single nucleotide polymorphisms within 16 confirmed genetic susceptibility loci for SLE were genotyped in a set of 804 Mestizo lupus patients and 667 Mestizo normal healthy controls. In addition, 347 admixture informative markers were genotyped. Individual ancestry proportions were determined using STRUCTURE. Association analysis was performed using PLINK, and correlation of the presence of risk alleles with ancestry was done using linear regression. Results A meta-analysis of the genetic association of the 16 SNPs across populations showed that TNFSF4, STAT4, PDCD1, ITGAM, and IRF5 were associated with lupus in a Hispanic-Mestizo cohort enriched for European and Amerindian ancestry. In addition, two SNPs within the MHC region, previously associated in a genome-wide association study in Europeans, were also associated in Mestizos. Using linear regression we predict an average increase of 2.34 risk alleles when comparing a lupus patient with 100% Amerindian ancestry to an SLE patient with 0% American Indian Ancestry (p<0.0001). SLE patients with 43% more Amerindian ancestry are predicted to carry one additional risk allele. Conclusion Amerindian ancestry increased the number of risk alleles for lupus. PMID:20848568

  16. New Method for Determining the Quality Factor and Resonance Frequency of Superconducting Micro-Resonators from Sonnet Simulations

    NASA Astrophysics Data System (ADS)

    Wisbey, D. S.; Martin, A.; Reinisch, A.; Gao, J.

    2014-08-01

    Lithographed superconducting microwave resonators (micro-resonators) are useful in a number of important applications, including microwave kinetic inductance detectors (Day et al., Nature 425:817, 2003), as memory elements in quantum information circuits, and as readouts of qubits and nanomechanical resonators. One of the major tasks in designing these devices is to find the resonance frequency (f) and quality factor (Q) for these microwave circuits using EM simulation software such as Sonnet. The traditional method iteratively runs simulations over successively smaller frequency ranges. In this way the simulated transmission S data is zoomed in on to yield a well-sampled resonance curve of a circuit. Designing microwave resonators in this manner is often time consuming since it requires many simulation runs. In this work, we show a new—and much faster—method for determining f and Q by adding an internal (virtual) port in the Sonnet model and examining the input impedance through the added port. Accurate f and Q values can be retrieved from a single simulation with a wide frequency sweep. This method works on many types of resonance circuits and dramatically reduces the simulation time.

  17. Bonds to the homeland: Patterns and determinants of women's transnational travel frequency among three immigrant groups in Germany.

    PubMed

    Iarmolenko, Svitlana; Titzmann, Peter F; Silbereisen, Rainer K

    2016-04-01

    Technology developments have changed immigrants' adaptation patterns in modern societies, allowing immigrants to sustain dense, complex connections with homeland while adjusting in the host country, a new phenomenon termed transnationalism. As empirical studies on immigrant transnationalism are still scarce, the purpose of this study was to investigate mean levels and determinants of a core component of transnationalism-transnational travel. Hypotheses were based on context of exiting homeland, living conditions in Germany and demographic and sociocultural variables. Transnational travel behaviour was assessed as frequency of return trips in three immigrant groups in Germany: ethnic Germans, Russian Jews and Turks. Interviews were conducted with 894 women participants from these groups. Results showed substantial transnational travel behaviour in all groups with Turks reporting higher levels than ethnic Germans and Russian Jews. Interindividual differences in transnational travel within groups were also examined. Results indicated similarities (e.g. network size in home country related positively to transnational travel frequency in all groups) and group-specific associations (e.g. co-ethnic identifying related positively to transnational travel frequency among Turks, but negatively for the other groups). Our study highlights the need for a new understanding of immigration and emphasises the consideration of group-specific mechanisms in transnational travel behaviour. PMID:25620296

  18. A Physical Inversion Approach for Determining True Temperature Sensitivity of Respiration from High-frequency Soil CO2 Datasets

    NASA Astrophysics Data System (ADS)

    Latimer, R.; Risk, D. A.

    2014-12-01

    Physical soil properties create lags between temperature change and corresponding soil responses, which obscure true Q10 values and other biophysical parameters such as depth of production. This study examines inversion approaches for estimating Q10 and depth of production using physically based soil models, constrained by observed high-frequency surface fluxes and/or concentrations. Our inversion strategy uses, at its base, a 1-D multi-layered soil model that simulates realistic temperature and gas diffusion physics. We tested inversion scenarios on synthetic datasets using a range of constraining parameters, time averaging techniques, mechanisms to improve computational efficiency, and various methods of incorporating real data into the model. Overall, we have found that with carefully constrained datasets, inversion was possible. While inversions using exclusively surface flux measurements could succeed, constraining the inversion using at least one shallow subsurface CO2 measurement proved to be most successful. Precision in modeling soil profile temperature was found to be crucial to the inversion process, along with the frequency of temperature measurements. This was not a surprise, given that temperature is the known determinant of soil lags. This presentation will share the various lessons from this work, and will illustrate these concepts using synthetic and real data. This work is a first step toward building a reliable framework for removing physical effects from high frequency soil CO2 datasets. Ultimately, we hope that this process will lead to better estimates of biophysical soil parameters and their variability on short timescales.

  19. Comparison of resonance frequencies of major atomic lines in 398-423 nm

    NASA Astrophysics Data System (ADS)

    Enomoto, Katsunari; Hizawa, Nagisa; Suzuki, Takahiro; Kobayashi, Kaori; Moriwaki, Yoshiki

    2016-05-01

    We have demonstrated spectroscopy of Ca, Rb, In, K, Ga, and Yb atomic lines in 398-423 nm. Using an etalon of an ultralow-expansion coefficient, we have determined ratios of the resonance frequencies of these atoms. The etalon has small group-delay-dispersion mirrors to be an accurate frequency reference over a wavelength span of a few tens of nanometer. The etalon resonance frequencies are calibrated with accurately known transition frequencies of Ca at 423 nm and Rb at 422 nm. Based on this calibration, the absolute frequencies are also determined for some atomic lines with smaller uncertainties than earlier reports.

  20. Method and apparatus for frequency spectrum analysis

    NASA Technical Reports Server (NTRS)

    Cole, Steven W. (Inventor)

    1992-01-01

    A method for frequency spectrum analysis of an unknown signal in real-time is discussed. The method is based upon integration of 1-bit samples of signal voltage amplitude corresponding to sine or cosine phases of a controlled center frequency clock which is changed after each integration interval to sweep the frequency range of interest in steps. Integration of samples during each interval is carried out over a number of cycles of the center frequency clock spanning a number of cycles of an input signal to be analyzed. The invention may be used to detect the frequency of at least two signals simultaneously. By using a reference signal of known frequency and voltage amplitude (added to the two signals for parallel processing in the same way, but in a different channel with a sampling at the known frequency and phases of the reference signal), the absolute voltage amplitude of the other two signals may be determined by squaring the sine and cosine integrals of each channel and summing the squares to obtain relative power measurements in all three channels and, from the known voltage amplitude of the reference signal, obtaining an absolute voltage measurement for the other two signals by multiplying the known voltage of the reference signal with the ratio of the relative power of each of the other two signals to the relative power of the reference signal.

  1. The AFGL absolute gravity program

    NASA Technical Reports Server (NTRS)

    Hammond, J. A.; Iliff, R. L.

    1978-01-01

    A brief discussion of the AFGL's (Air Force Geophysics Laboratory) program in absolute gravity is presented. Support of outside work and in-house studies relating to gravity instrumentation are discussed. A description of the current transportable system is included and the latest results are presented. These results show good agreement with measurements at the AFGL site by an Italian system. The accuracy obtained by the transportable apparatus is better than 0.1 microns sq sec 10 microgal and agreement with previous measurements is within the combined uncertainties of the measurements.

  2. Automatically determining the origin direction and propagation mode of high-frequency radar backscatter

    NASA Astrophysics Data System (ADS)

    Burrell, Angeline G.; Milan, Stephen E.; Perry, Gareth W.; Yeoman, Timothy K.; Lester, Mark

    2015-12-01

    Elevation angles of returned backscatter are calculated at Super Dual Auroral Radar Network radars using interferometric techniques. These elevation angles allow the altitude of the reflection point to be estimated, an essential piece of information for many ionospheric studies. The elevation angle calculation requires knowledge of the azimuthal return angle. This directional angle is usually assumed to lie along a narrow beam from the front of the radar, even though the signals are known to return from both in front of and behind the radar. If the wrong direction of return is assumed, large uncertainties will be introduced through the azimuthal return angle. This paper introduces a means of automatically determining the correct direction of arrival and the propagation mode of backscatter. The application of this method will improve the accuracy of backscatter elevation angle data and aid in the interpretation of both ionospheric and ground backscatter observations.

  3. Dual-Frequency Alternating Current Designer Waveform for Reliable Voltammetric Determination of Electrode Kinetics Approaching the Reversible Limit.

    PubMed

    Li, Jiezhen; Bentley, Cameron L; Bond, Alan M; Zhang, Jie

    2016-02-16

    Alternating current (ac) voltammetry provides access to faster electrode kinetics than direct current (dc) methods. However, difficulties in ac and other methods arise when the heterogeneous electron-transfer rate constant (k(0)) approaches the reversible limit, because the voltammetric characteristics become insensitive to electrode kinetics. Thus, in this near-reversible regime, even small uncertainties associated with bulk concentration (C), diffusion coefficient (D), electrode area (A), and uncompensated resistance (Ru) can lead to significant systematic error in the determination of k(0). In this study, we have introduced a kinetically sensitive dual-frequency designer waveform into the Fourier-transformed large-amplitude alternating current (FTAC) voltammetric method that is made up of two sine waves having the same amplitude but with different frequencies (e.g., 37 and 615 Hz) superimposed onto a dc ramp to quantify the close-to-reversible Fc(0/+) process (Fc = ferrocene) in two nonhaloaluminate ionic liquids. The concept is that from a single experiment the lower-frequency data set, collected on a time scale where the target process is reversible, can be used as an internal reference to calibrate A, D, C, and Ru. These calibrated values are then used to calculate k(0) from analysis of the harmonics of the higher-frequency data set, where the target process is quasi-reversible. With this approach, k(0) values of 0.28 and 0.11 cm·s(-1) have been obtained at a 50 μm diameter platinum microdisk electrode for the close-to-diffusion-controlled Fc(0/+) process in two ionic liquids, 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide and 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide, respectively. PMID:26771276

  4. Absolute luminosity measurements with the LHCb detector at the LHC

    NASA Astrophysics Data System (ADS)

    LHCb Collaboration

    2012-01-01

    Absolute luminosity measurements are of general interest for colliding-beam experiments at storage rings. These measurements are necessary to determine the absolute cross-sections of reaction processes and are valuable to quantify the performance of the accelerator. Using data taken in 2010, LHCb has applied two methods to determine the absolute scale of its luminosity measurements for proton-proton collisions at the LHC with a centre-of-mass energy of 7 TeV. In addition to the classic ``van der Meer scan'' method a novel technique has been developed which makes use of direct imaging of the individual beams using beam-gas and beam-beam interactions. This beam imaging method is made possible by the high resolution of the LHCb vertex detector and the close proximity of the detector to the beams, and allows beam parameters such as positions, angles and widths to be determined. The results of the two methods have comparable precision and are in good agreement. Combining the two methods, an overal precision of 3.5% in the absolute luminosity determination is reached. The techniques used to transport the absolute luminosity calibration to the full 2010 data-taking period are presented.

  5. Achieving Climate Change Absolute Accuracy in Orbit

    NASA Technical Reports Server (NTRS)

    Wielicki, Bruce A.; Young, D. F.; Mlynczak, M. G.; Thome, K. J; Leroy, S.; Corliss, J.; Anderson, J. G.; Ao, C. O.; Bantges, R.; Best, F.; Bowman, K.; Brindley, H.; Butler, J. J.; Collins, W.; Dykema, J. A.; Doelling, D. R.; Feldman, D. R.; Fox, N.; Huang, X.; Holz, R.; Huang, Y.; Jennings, D.; Jin, Z.; Johnson, D. G.; Jucks, K.; Kato, S.; Kratz, D. P.; Liu, X.; Lukashin, C.; Mannucci, A. J.; Phojanamongkolkij, N.; Roithmayr, C. M.; Sandford, S.; Taylor, P. C.; Xiong, X.

    2013-01-01

    The Climate Absolute Radiance and Refractivity Observatory (CLARREO) mission will provide a calibration laboratory in orbit for the purpose of accurately measuring and attributing climate change. CLARREO measurements establish new climate change benchmarks with high absolute radiometric accuracy and high statistical confidence across a wide range of essential climate variables. CLARREO's inherently high absolute accuracy will be verified and traceable on orbit to Système Internationale (SI) units. The benchmarks established by CLARREO will be critical for assessing changes in the Earth system and climate model predictive capabilities for decades into the future as society works to meet the challenge of optimizing strategies for mitigating and adapting to climate change. The CLARREO benchmarks are derived from measurements of the Earth's thermal infrared spectrum (5-50 micron), the spectrum of solar radiation reflected by the Earth and its atmosphere (320-2300 nm), and radio occultation refractivity from which accurate temperature profiles are derived. The mission has the ability to provide new spectral fingerprints of climate change, as well as to provide the first orbiting radiometer with accuracy sufficient to serve as the reference transfer standard for other space sensors, in essence serving as a "NIST [National Institute of Standards and Technology] in orbit." CLARREO will greatly improve the accuracy and relevance of a wide range of space-borne instruments for decadal climate change. Finally, CLARREO has developed new metrics and methods for determining the accuracy requirements of climate observations for a wide range of climate variables and uncertainty sources. These methods should be useful for improving our understanding of observing requirements for most climate change observations.

  6. The Application of GIM in Precise Orbit Determination for LEO Satellites with Single-Frequency GPS Measurements

    NASA Astrophysics Data System (ADS)

    Peng, Dong-ju; Wu, Bin

    2012-10-01

    With the precise GPS ephemeris and clock error available, the iono- spheric delay is left as the dominant error source in the single-frequency GPS data. Thus, the removal of ionospheric effects is a ma jor prerequisite for an improved orbit reconstruction of LEO satellites based on the single-frequency GPS data. In this paper, the use of Global Ionospheric Maps (GIM) in kine- matic and dynamic orbit determinations for LEO satellites with single-frequency GPS pseudorange measurements is discussed first, and then, estimating the iono- spheric scale factor to remove the ionospheric effects from the C/A-code pseu- dorange measurements for both kinematic and dynamic orbit determinations is addressed. As it is known that the ionospheric delay of space-borne GPS sig- nals is strongly dependent on the orbit altitudes of LEO satellites, we select the real C/A-code pseudorange measurement data of the CHAMP, GRACE, TerraSAR-X and SAC-C satellites with altitudes between 300 km and 800 km as sample data in this paper. It is demonstrated that the approach to eliminating ionospheric effects in C/A-code pseudorange measurements by estimating the ionospheric scale factor is highly effective. Employing this approach, the accu- racy of both kinematic and dynamic orbits can be improved notably. Among those five LEO satellites, CHAMP with the lowest orbit altitude has the most remarkable improvements in orbit accuracy, which are 55.6% and 47.6% for kine- matic and dynamic orbits, respectively. SAC-C with the highest orbit altitude has the least improvements in orbit accuracy accordingly, which are 47.8% and 38.2%, respectively.

  7. C≡N stretching vibration of 5-cyanotryptophan as an infrared probe of protein local environment: what determines its frequency?

    PubMed

    Zhang, Wenkai; Markiewicz, Beatrice N; Doerksen, Rosalie S; Smith Iii, Amos B; Gai, Feng

    2016-03-14

    Recently it has been suggested that the C≡N stretching vibration of a tryptophan analog, 5-cyanotryptophan, could be used as an infrared probe of the local environment, especially the hydration status, of tryptophan residues in proteins. However, the factors that influence the frequency of this vibrational mode are not understood. To determine these factors, herein we carried out linear and nonlinear infrared measurements on the C≡N stretching vibration of the sidechain of 5-cyanotryptophan, 3-methyl-5-cyanoindole, in a series of protic and aprotic solvents. We found that while the C≡N stretching frequencies obtained in these solvents do not correlate well with any individual Kamlet-Taft solvent parameter, i.e., π* (polarizability), β (hydrogen bond accepting ability), and α (hydrogen bond donating ability), they do however, collapse on a straight line when plotted against σ = π* + β - α. This linear relationship provides a firm indication that both specific interactions, i.e., hydrogen-bonding interactions with the C≡N (through α) and indole N-H (through β) groups, and non-specific interactions with the molecule (through π*) work together to determine the C≡N stretching frequency, thus laying a quantitative framework for applying 5-cyanotryptophan to investigate the microscopic environment of proteins in a site-specific manner. Furthermore, two-dimensional and pump-probe infrared measurements revealed that a significant portion (∼31%) of the ground state bleach signal has a decay time constant of ∼12.3 ps, due to an additional vibrational relaxation channel, making it possible to use 5-cyanotryptophan to probe dynamics occurring on a timescale on the order of tens of picoseconds. PMID:26343769

  8. Focal mechanism determination using high-frequency waveform matching and its application to small magnitude induced earthquakes

    NASA Astrophysics Data System (ADS)

    Li, Junlun; Zhang, Haijiang; Sadi Kuleli, H.; Nafi Toksoz, M.

    2011-03-01

    We present a new method using high-frequency full waveform information to determine the focal mechanisms of small, local earthquakes monitored by a sparse surface network. During the waveform inversion, we maximize both the phase and amplitude matching between the observed and modelled waveforms. In addition, we use the polarities of the first P-wave arrivals and the average S/P amplitude ratios to better constrain the matching. An objective function is constructed to include all four criteria. An optimized grid search method is used to search over all possible ranges of source parameters (strike, dip and rake). To speed up the algorithm, a library of Green's functions is pre-calculated for each of the moment tensor components and possible earthquake locations. Optimizations in filtering and cross correlation are performed to further speed the grid search algorithm. The new method is tested on a five-station surface network used for monitoring induced seismicity at a petroleum field. The synthetic test showed that our method is robust and efficient to determine the focal mechanism when using only the vertical component of seismograms in the frequency range of 3-9 Hz. The application to dozens of induced seismic events showed satisfactory waveform matching between modelled and observed seismograms. The majority of the events have a strike direction parallel with the major NE-SW faults in the region. The normal faulting mechanism is dominant, which suggests the vertical stress is larger than the horizontal stress.

  9. Absolute calibration of ultraviolet filter photometry

    NASA Technical Reports Server (NTRS)

    Bless, R. C.; Fairchild, T.; Code, A. D.

    1972-01-01

    The essential features of the calibration procedure can be divided into three parts. First, the shape of the bandpass of each photometer was determined by measuring the transmissions of the individual optical components and also by measuring the response of the photometer as a whole. Secondly, each photometer was placed in the essentially-collimated synchrotron radiation bundle maintained at a constant intensity level, and the output signal was determined from about 100 points on the objective. Finally, two or three points on the objective were illuminated by synchrotron radiation at several different intensity levels covering the dynamic range of the photometers. The output signals were placed on an absolute basis by the electron counting technique described earlier.

  10. Sharpness of upper-mantle discontinuities determined from high-frequency reflections

    USGS Publications Warehouse

    Benz, H.M.; Vidale, J.E.

    1993-01-01

    AN understanding of the nature of seismic discontinuities in the Earth's upper mantle is important for understanding mantle processes: in particular, the amplitude and sharpness of these discontinuities are critical for assessing models of upper-mantle phase changes and chemical layering. So far, seismic studies aimed at determining the thickness and lateral variability of upper-mantle discontinuities have yielded equivocal results, particularly for the discontinuity at 410km depth1,2. Here we present short-period (0.8-2.0 s) recordings of upper-mantle precursors to the seismic phase P???P??? (PKPPKP) from two South American earthquakes recorded by the ???700-station short-period array in California. Our results show that the 410- and 660-km discontinuities beneath the Indian Ocean are locally simple and sharp, corresponding to transition zones of 4 km or less. These observations pose problems for mineral physics models3-5, which predict a transitional thickness greater than 6 km for the peridotite to ??-spinel phase transition. In contrast to the results of long-period studies6,7, we observe no short-period arrivals from near 520 km depth.

  11. Sharpness of upper-mantle discontinuities determined from high-frequency reflections

    USGS Publications Warehouse

    Benz, H.M.; Vidale, J.E.

    1993-01-01

    AN understanding of the nature of seismic discontinuities in the Earth's upper mantle is important for understanding mantle processes: in particular, the amplitude and sharpness of these discontinuities are critical for assessing models of upper-mantle phase changes and chemical layering. So far, seismic studies aimed at determining the thickness and lateral variability of upper-mantle discontinuities have yielded equivocal results, particularly for the discontinuity at 410km depth1,2. Here we present short-period (0.8-2.0 s) recordings of upper-mantle precursors to the seismic phase P???P??? (PKPPKP) from two South American earthquakes recorded by the ???700-station short-period array in California. Our results show that the 410- and 660-km discontinuities beneath the Indian Ocean are locally simple and sharp, corresponding to transi-tion zones of 4 km or less. These observations pose problems for mineral physics models3-5, which predict a transitional thickness greater than 6 km for the peridotite to ??-spinel phase transition. In contrast to the results of long-period studies6,7, we observe no short-period arrivals from near 520 km depth. ?? 1993 Nature Publishing Group.

  12. Determinants of frequency-dependent regulation of Kv1.2-containing potassium channels

    PubMed Central

    Baronas, Victoria A.; Yang, Runying; Vilin, Yury Y.; Kurata, Harley T.

    2016-01-01

    ABSTRACT Voltage-gated potassium channels are important regulators of electrical excitation in many tissues, with Kv1.2 standing out as an essential contributor in the CNS. Genetic deletion of Kv1.2 invariably leads to early lethality in mice. In humans, mutations affecting Kv1.2 function are linked to epileptic encephalopathy and movement disorders. We have demonstrated that Kv1.2 is subject to a unique regulatory mechanism in which repetitive stimulation leads to dramatic potentiation of current. In this study, we explore the properties and molecular determinants of this use-dependent potentiation/activation. First, we examine how alterations in duty cycle (depolarization and repolarization/recovery times) affect the onset and extent of use-dependent activation. Also, we use trains of repetitive depolarizations to test the effects of a variety of Thr252 (S2-S3 linker) mutations on use-dependent activation. Substitutions of Thr with some sterically similar amino acids (Ser, Val, and Met, but not Cys) retain use-dependent activation, while bulky or charged amino acid substitutions eliminate use-dependence. Introduction of Thr at the equivalent position in other Kv1 channels (1.1, 1.3, 1.4), was not sufficient to transfer the phenotype. We hypothesize that use-dependent activation of Kv1.2 channels is mediated by an extrinsic regulator that binds preferentially to the channel closed state, with Thr252 being necessary but not sufficient for this interaction to alter channel function. These findings extend the conclusions of our recent demonstration of use-dependent activation of Kv1.2-containing channels in hippocampal neurons, by adding new details about the molecular mechanism underlying this effect. PMID:26646078

  13. The Splicing Efficiency of Activating HRAS Mutations Can Determine Costello Syndrome Phenotype and Frequency in Cancer.

    PubMed

    Hartung, Anne-Mette; Swensen, Jeff; Uriz, Inaki E; Lapin, Morten; Kristjansdottir, Karen; Petersen, Ulrika S S; Bang, Jeanne Mari V; Guerra, Barbara; Andersen, Henriette Skovgaard; Dobrowolski, Steven F; Carey, John C; Yu, Ping; Vaughn, Cecily; Calhoun, Amy; Larsen, Martin R; Dyrskjøt, Lars; Stevenson, David A; Andresen, Brage S

    2016-05-01

    Costello syndrome (CS) may be caused by activating mutations in codon 12/13 of the HRAS proto-oncogene. HRAS p.Gly12Val mutations have the highest transforming activity, are very frequent in cancers, but very rare in CS, where they are reported to cause a severe, early lethal, phenotype. We identified an unusual, new germline p.Gly12Val mutation, c.35_36GC>TG, in a 12-year-old boy with attenuated CS. Analysis of his HRAS cDNA showed high levels of exon 2 skipping. Using wild type and mutant HRAS minigenes, we confirmed that c.35_36GC>TG results in exon 2 skipping by simultaneously disrupting the function of a critical Exonic Splicing Enhancer (ESE) and creation of an Exonic Splicing Silencer (ESS). We show that this vulnerability of HRAS exon 2 is caused by a weak 3' splice site, which makes exon 2 inclusion dependent on binding of splicing stimulatory proteins, like SRSF2, to the critical ESE. Because the majority of cancer- and CS- causing mutations are located here, they affect splicing differently. Therefore, our results also demonstrate that the phenotype in CS and somatic cancers is not only determined by the different transforming potentials of mutant HRAS proteins, but also by the efficiency of exon 2 inclusion resulting from the different HRAS mutations. Finally, we show that a splice switching oligonucleotide (SSO) that blocks access to the critical ESE causes exon 2 skipping and halts proliferation of cancer cells. This unravels a potential for development of new anti-cancer therapies based on SSO-mediated HRAS exon 2 skipping. PMID:27195699

  14. The Splicing Efficiency of Activating HRAS Mutations Can Determine Costello Syndrome Phenotype and Frequency in Cancer

    PubMed Central

    Kristjansdottir, Karen; Petersen, Ulrika S. S.; Bang, Jeanne Mari V.; Guerra, Barbara; Andersen, Henriette Skovgaard; Dobrowolski, Steven F.; Carey, John C.; Yu, Ping; Calhoun, Amy; Larsen, Martin R.; Dyrskjøt, Lars; Stevenson, David A.; Andresen, Brage S.

    2016-01-01

    Costello syndrome (CS) may be caused by activating mutations in codon 12/13 of the HRAS proto-oncogene. HRAS p.Gly12Val mutations have the highest transforming activity, are very frequent in cancers, but very rare in CS, where they are reported to cause a severe, early lethal, phenotype. We identified an unusual, new germline p.Gly12Val mutation, c.35_36GC>TG, in a 12-year-old boy with attenuated CS. Analysis of his HRAS cDNA showed high levels of exon 2 skipping. Using wild type and mutant HRAS minigenes, we confirmed that c.35_36GC>TG results in exon 2 skipping by simultaneously disrupting the function of a critical Exonic Splicing Enhancer (ESE) and creation of an Exonic Splicing Silencer (ESS). We show that this vulnerability of HRAS exon 2 is caused by a weak 3’ splice site, which makes exon 2 inclusion dependent on binding of splicing stimulatory proteins, like SRSF2, to the critical ESE. Because the majority of cancer- and CS- causing mutations are located here, they affect splicing differently. Therefore, our results also demonstrate that the phenotype in CS and somatic cancers is not only determined by the different transforming potentials of mutant HRAS proteins, but also by the efficiency of exon 2 inclusion resulting from the different HRAS mutations. Finally, we show that a splice switching oligonucleotide (SSO) that blocks access to the critical ESE causes exon 2 skipping and halts proliferation of cancer cells. This unravels a potential for development of new anti-cancer therapies based on SSO-mediated HRAS exon 2 skipping. PMID:27195699

  15. Global absolut gravity reference system as replacement of IGSN 71

    NASA Astrophysics Data System (ADS)

    Wilmes, Herbert; Wziontek, Hartmut; Falk, Reinhard

    2015-04-01

    The determination of precise gravity field parameters is of great importance in a period in which earth sciences are achieving the necessary accuracy to monitor and document global change processes. This is the reason why experts from geodesy and metrology joined in a successful cooperation to make absolute gravity observations traceable to SI quantities, to improve the metrological kilogram definition and to monitor mass movements and smallest height changes for geodetic and geophysical applications. The international gravity datum is still defined by the International Gravity Standardization Net adopted in 1971 (IGSN 71). The network is based upon pendulum and spring gravimeter observations taken in the 1950s and 60s supported by the early free fall absolute gravimeters. Its gravity values agreed in every case to better than 0.1 mGal. Today, more than 100 absolute gravimeters are in use worldwide. The series of repeated international comparisons confirms the traceability of absolute gravity measurements to SI quantities and confirm the degree of equivalence of the gravimeters in the order of a few µGal. For applications in geosciences where e.g. gravity changes over time need to be analyzed, the temporal stability of an absolute gravimeter is most important. Therefore, the proposition is made to replace the IGSN 71 by an up-to-date gravity reference system which is based upon repeated absolute gravimeter comparisons and a global network of well controlled gravity reference stations.

  16. Standardization of the cumulative absolute velocity

    SciTech Connect

    O'Hara, T.F.; Jacobson, J.P. )

    1991-12-01

    EPRI NP-5930, A Criterion for Determining Exceedance of the Operating Basis Earthquake,'' was published in July 1988. As defined in that report, the Operating Basis Earthquake (OBE) is exceeded when both a response spectrum parameter and a second damage parameter, referred to as the Cumulative Absolute Velocity (CAV), are exceeded. In the review process of the above report, it was noted that the calculation of CAV could be confounded by time history records of long duration containing low (nondamaging) acceleration. Therefore, it is necessary to standardize the method of calculating CAV to account for record length. This standardized methodology allows consistent comparisons between future CAV calculations and the adjusted CAV threshold value based upon applying the standardized methodology to the data set presented in EPRI NP-5930. The recommended method to standardize the CAV calculation is to window its calculation on a second-by-second basis for a given time history. If the absolute acceleration exceeds 0.025g at any time during each one second interval, the earthquake records used in EPRI NP-5930 have been reanalyzed and the adjusted threshold of damage for CAV was found to be 0.16g-set.

  17. Transient absolute robustness in stochastic biochemical networks.

    PubMed

    Enciso, German A

    2016-08-01

    Absolute robustness allows biochemical networks to sustain a consistent steady-state output in the face of protein concentration variability from cell to cell. This property is structural and can be determined from the topology of the network alone regardless of rate parameters. An important question regarding these systems is the effect of discrete biochemical noise in the dynamical behaviour. In this paper, a variable freezing technique is developed to show that under mild hypotheses the corresponding stochastic system has a transiently robust behaviour. Specifically, after finite time the distribution of the output approximates a Poisson distribution, centred around the deterministic mean. The approximation becomes increasingly accurate, and it holds for increasingly long finite times, as the total protein concentrations grow to infinity. In particular, the stochastic system retains a transient, absolutely robust behaviour corresponding to the deterministic case. This result contrasts with the long-term dynamics of the stochastic system, which eventually must undergo an extinction event that eliminates robustness and is completely different from the deterministic dynamics. The transiently robust behaviour may be sufficient to carry out many forms of robust signal transduction and cellular decision-making in cellular organisms. PMID:27581485

  18. In-flight absolute radiometric calibration of the thematic mapper

    NASA Technical Reports Server (NTRS)

    Castle, K. R.; Holm, R. G.; Kastner, C. J.; Palmer, J. M.; Slater, P. N.; Dinguirard, M.; Ezra, C. E.; Jackson, R. D.; Savage, R. K.

    1983-01-01

    The TM multispectral scanner system was calibrated in an absolute manner before launch. To determine the temporal changes of the absolute radiometric calibration of the entire system, spectroradiometric measurements of the ground and the atmosphere were made simultaneously with TM collections over White Sands, New Mexico. By entering the measured values in an atmospheric radiative transfer program, the radiance levels of the in four of the spectral bands of the TM were determined. Tables show values for the reflectance of snow at White Sands measured by a modular 8 channel radiometer, and values for exoatmospheric irradiance within the TM passbands, calculated for the Earth-Sun distance using a solar radiometer.

  19. Cosmology with negative absolute temperatures

    NASA Astrophysics Data System (ADS)

    Vieira, J. P. P.; Byrnes, Christian T.; Lewis, Antony

    2016-08-01

    Negative absolute temperatures (NAT) are an exotic thermodynamical consequence of quantum physics which has been known since the 1950's (having been achieved in the lab on a number of occasions). Recently, the work of Braun et al. [1] has rekindled interest in negative temperatures and hinted at a possibility of using NAT systems in the lab as dark energy analogues. This paper goes one step further, looking into the cosmological consequences of the existence of a NAT component in the Universe. NAT-dominated expanding Universes experience a borderline phantom expansion (w < ‑1) with no Big Rip, and their contracting counterparts are forced to bounce after the energy density becomes sufficiently large. Both scenarios might be used to solve horizon and flatness problems analogously to standard inflation and bouncing cosmologies. We discuss the difficulties in obtaining and ending a NAT-dominated epoch, and possible ways of obtaining density perturbations with an acceptable spectrum.

  20. The problem of selecting an optimum frequency for a measuring generator in determining the value of the hydrophysical parameter with a given accuracy

    NASA Technical Reports Server (NTRS)

    Stepanyuk, V. A.

    1974-01-01

    The selection of the optimum frequency for a measuring generator for determining the value of the hydrophysical parameter with a given degree of accuracy is discussed. Methods from information theory for measuring generators are described. Conversion of the frequency of generators into digital form by means of statistical averaging is also described.

  1. The Application of GIM in Precise Orbit Determination for LEO Satellites with Single-frequency GPS Measurements

    NASA Astrophysics Data System (ADS)

    Peng, D. J.; Wu, B.

    2012-01-01

    With the availability of precise GPS ephemeris and clock solution, the ionospheric range delay is left as the dominant error sources in the post-processing of space-borne GPS data from single-frequency receivers. Thus, the removal of ionospheric effects is a major prerequisite for an improved orbit reconstruction of LEO satellites equipped with low cost single-frequency GPS receivers. In this paper, the use of Global Ionospheric Maps (GIM) in kinematic and dynamic orbit determination for LEO satellites with single-frequency GPS measurements is discussed first,and then, estimating the scale factor of ionosphere to remove the ionospheric effects in C/A code pseudo-range measurements in both kinematic and adynamia orbit defemination approaches is addressed. As it is known the ionospheric path delay of space-borne GPS signals is strongly dependent on the orbit altitudes of LEO satellites, we selected real space-borne GPS data from CHAMP, GRACE, TerraSAR-X and SAC-C satellites with altitudes between 300 km and 800 km as sample data in this paper. It is demonstrated that the approach of eliminating ionospheric effects in space-borne C/A code pseudo-range by estimating the scale factor of ionosphere is highly effective. Employing this approach, the accuracy of both kinematic and dynamic orbits can be improved notably. Among those five LEO satellites, CHAMP with the lowest orbit altitude has the most remarkable orbit accuracy improvements, which are 55.6% and 47.6% for kinematic and dynamic approaches, respectively. SAC-C with the highest orbit altitude has the least orbit accuracy improvements accordingly, which are 47.8% and 38.2%, respectively.

  2. Absolute phase effects on CPMG-type pulse sequences

    NASA Astrophysics Data System (ADS)

    Mandal, Soumyajit; Oh, Sangwon; Hürlimann, Martin D.

    2015-12-01

    We describe and analyze the effects of transients within radio-frequency (RF) pulses on multiple-pulse NMR measurements such as the well-known Carr-Purcell-Meiboom-Gill (CPMG) sequence. These transients are functions of the absolute RF phases at the beginning and end of the pulse, and are thus affected by the timing of the pulse sequence with respect to the period of the RF waveform. Changes in transients between refocusing pulses in CPMG-type sequences can result in signal decay, persistent oscillations, changes in echo shape, and other effects. We have explored such effects by performing experiments in two different low-frequency NMR systems. The first uses a conventional tuned-and-matched probe circuit, while the second uses an ultra-broadband un-tuned or non-resonant probe circuit. We show that there are distinct differences between the absolute phase effects in these two systems, and present simple models that explain these differences.

  3. Determining Free-Radical Propagation Rate Coefficients with High-Frequency Lasers: Current Status and Future Perspectives.

    PubMed

    Kockler, Katrin B; Haehnel, Alexander P; Junkers, Thomas; Barner-Kowollik, Christopher

    2016-01-01

    Detailed knowledge of the polymerization mechanisms and kinetics of academically and industrially relevant monomers is mandatory for the precision synthesis of tailor-made polymers. The IUPAC-recommended pulsed-laser polymerization-size exclusion chromatography (PLP-SEC) approach is the method of choice for the determination of propagation rate coefficients and the associated Arrhenius parameters for free radical polymerization processes. With regard to specific monomer classes-such as acrylate-type monomers, which are very important from a materials point of view-high laser frequencies of up to 500 Hz are mandatory to prevent the formation of mid-chain radicals and the occurrence of chain-breaking events by chain transfer, if industrially relevant temperatures are to be reached and wide temperature ranges are to be explored (up to 70 °C). Herein the progress and state-of-the-art of high-frequency PLP-SEC with pulse repetition rates of 500 Hz is reported, with a critical collection of to-date investigated 500 Hz data as well as future perspectives for the field. PMID:26479174

  4. To determine the frequency of Factor V Leiden in cases of Deep Vein Thrombosis and Healthy controls

    PubMed Central

    Saeed, Anjum; Sumreen; Kashif, Muhammad Ali

    2015-01-01

    Objective: To determine the frequency of Factor V Leiden in cases of Deep Vein Thrombosis and Healthy controls. Methods: This case control study was performed in Armed Forces Institute of Pathology Rawalpindi, From 21st March to 25th September 2013. One hundred patients with diagnostic evidence of Deep vein thrombosis on Doppler ultrasound/Magnetic resonance imaging (MRI) scan were included in the study through non probability convenient sampling and compared with 100 matched healthy controls. DNA was extracted from the blood sample by kit method. In order to identify Factor V Leiden mutation, the polymerase chain reaction (PCR) method was utilized combined with the Amplification refractory mutation system. Data was analyzed using statistical package for social sciences (SPSS) version 17. Results: In 100 patients of Deep Vein Thrombosis (DVT), frequency of Factor V Leiden (FVL) was 13% and it is was 2% in healthy control group. A significant association was found between FVL and DVT with odds ratio of 7.32 and with P value (P = 0.003). Conclusion: FVL was found to be highly prevalent among patients of DVT, Signifying strong association between the two. PMID:26649017

  5. Method and apparatus for two-dimensional absolute optical encoding

    NASA Technical Reports Server (NTRS)

    Leviton, Douglas B. (Inventor)

    2004-01-01

    This invention presents a two-dimensional absolute optical encoder and a method for determining position of an object in accordance with information from the encoder. The encoder of the present invention comprises a scale having a pattern being predetermined to indicate an absolute location on the scale, means for illuminating the scale, means for forming an image of the pattern; and detector means for outputting signals derived from the portion of the image of the pattern which lies within a field of view of the detector means, the field of view defining an image reference coordinate system, and analyzing means, receiving the signals from the detector means, for determining the absolute location of the object. There are two types of scale patterns presented in this invention: grid type and starfield type.

  6. Quantitative fluorescence imaging of protoporphyrin IX through determination of tissue optical properties in the spatial frequency domain

    NASA Astrophysics Data System (ADS)

    Saager, Rolf B.; Cuccia, David J.; Saggese, Steve; Kelly, Kristen M.; Durkin, Anthony J.

    2011-12-01

    The ability to quantitatively determine tissue fluorescence is of interest for the purpose of better understanding the details of photodynamic therapy of skin cancer. In particular, we are interested in quantifying protoporphyrin IX (PpIX) in vivo. We present a method of correcting fluorescence for effects of native tissue absorption and scattering properties in a spatially resolved manner that preserves the resolution of the fluorescence imaging system, based off a homogeneous representation of tissue. Validation was performed using a series of liquid turbid phantoms having varying concentrations of absorber, scatterer, and fluorophore (PpIX). Through the quantification of tissue optical properties via spatial frequency domain imaging, an empirical model based on Monte Carlo simulations was deployed to successfully decouple the effects of absorption and scattering from fluorescence. From this we were able to deduce the concentration of the PpIX to within 0.2 μg/ml of the known concentration. This method was subsequently applied to the determination of PpIX concentration from in vivo normal skin where the model-based correction determined a concentration of 1.6 μg/ml, which is in agreement with literature.

  7. Frequency-Domain Approach To Determine Magnetic Address-Sensor Separation Distance Using the Harmonic Ratio Method.

    PubMed

    Young, Colin C; Blackley, Benjamin W; Porter, Marc D; Granger, Michael C

    2016-02-16

    In this work, we describe an approach to determine the distance separating a magnetic address from a scanning magnetoresistive sensor, a critical adjustable parameter for certain bioassay analyses where magnetic nanoparticles are used as labels. Our approach is leveraged from the harmonic ratio method (HRM), a method used in the hard drive industry to control the distance separating a magnetoresistive read head from its data platter with nanometer resolution. At the heart of the HRM is an amplitude comparison of a signal's fundamental frequency to that of its harmonics. When the signal is derived from the magnetic field pattern of a periodic array of magnetic addresses, the harmonic ratio contains the information necessary to determine the separation between the address array and the read head. The elegance of the HRM is that there is no need of additional components to the detection platform to determine a separation distance; the streaming "bit signal" contains all the information needed. In this work, we demonstrate that the tenets governing HRM used in the hard drive industry can be applied to the bioanalytical arena where submicrometer to 100 μm separations are required. PMID:26879366

  8. A compact proton spectrometer for measurement of the absolute DD proton spectrum from which yield and ρR are determined in thin-shell inertial-confinement-fusion implosions

    NASA Astrophysics Data System (ADS)

    Rosenberg, M. J.; Zylstra, A. B.; Frenje, J. A.; Rinderknecht, H. G.; Gatu Johnson, M.; Waugh, C. J.; Séguin, F. H.; Sio, H.; Sinenian, N.; Li, C. K.; Petrasso, R. D.; Glebov, V. Yu.; Hohenberger, M.; Stoeckl, C.; Sangster, T. C.; Yeamans, C. B.; LePape, S.; Mackinnon, A. J.; Bionta, R. M.; Talison, B.; Casey, D. T.; Landen, O. L.; Moran, M. J.; Zacharias, R. A.; Kilkenny, J. D.; Nikroo, A.

    2014-10-01

    A compact, step range filter proton spectrometer has been developed for the measurement of the absolute DD proton spectrum, from which yield and areal density (ρR) are inferred for deuterium-filled thin-shell inertial confinement fusion implosions. This spectrometer, which is based on tantalum step-range filters, is sensitive to protons in the energy range 1-9 MeV and can be used to measure proton spectra at mean energies of ˜1-3 MeV. It has been developed and implemented using a linear accelerator and applied to experiments at the OMEGA laser facility and the National Ignition Facility (NIF). Modeling of the proton slowing in the filters is necessary to construct the spectrum, and the yield and energy uncertainties are ±<10% in yield and ±120 keV, respectively. This spectrometer can be used for in situ calibration of DD-neutron yield diagnostics at the NIF.

  9. The synthesis of [(14) C]AZD5122. Incorporation of an IV (14) C-microtracer dose into a first in human study to determine the absolute oral bioavailability of AZD5122.

    PubMed

    Hickey, Michael J; Allen, Paul H; Kingston, Lee P; Wilkinson, David J

    2016-05-30

    AZD5122, N-(2-(2,3-difluorobenzylthio)-6-((2R,3R)-3,4-dihydroxybutan-2-ylamino)pyrimidin-4-yl)azetidine-1-sulfonamide was under investigation as a potential chemokine receptor CXCR2 antagonist for the treatment for inflammatory diseases. To gain a better understanding of the human pharmacokinetic profile, an exploratory phase I IV microtracer study was conducted using carbon-14 radiolabelled AZD5122. [(14) C]AZD5122 was carbon-14 labelled in the pyrimidine ring in five steps in an overall radiochemical yield of 19% from [(14) C]thiourea. The absolute oral bioavailability of AZD5122 was assessed in healthy subjects by an oral administration of AZD5122, followed by a concomitant intravenous [(14) C]AZD5122 microdose. PMID:27169760

  10. A compact proton spectrometer for measurement of the absolute DD proton spectrum from which yield and ρR are determined in thin-shell inertial-confinement-fusion implosions.

    PubMed

    Rosenberg, M J; Zylstra, A B; Frenje, J A; Rinderknecht, H G; Johnson, M Gatu; Waugh, C J; Séguin, F H; Sio, H; Sinenian, N; Li, C K; Petrasso, R D; Glebov, V Yu; Hohenberger, M; Stoeckl, C; Sangster, T C; Yeamans, C B; LePape, S; Mackinnon, A J; Bionta, R M; Talison, B; Casey, D T; Landen, O L; Moran, M J; Zacharias, R A; Kilkenny, J D; Nikroo, A

    2014-10-01

    A compact, step range filter proton spectrometer has been developed for the measurement of the absolute DD proton spectrum, from which yield and areal density (ρR) are inferred for deuterium-filled thin-shell inertial confinement fusion implosions. This spectrometer, which is based on tantalum step-range filters, is sensitive to protons in the energy range 1-9 MeV and can be used to measure proton spectra at mean energies of ∼1-3 MeV. It has been developed and implemented using a linear accelerator and applied to experiments at the OMEGA laser facility and the National Ignition Facility (NIF). Modeling of the proton slowing in the filters is necessary to construct the spectrum, and the yield and energy uncertainties are ±<10% in yield and ±120 keV, respectively. This spectrometer can be used for in situ calibration of DD-neutron yield diagnostics at the NIF. PMID:25362390

  11. A compact proton spectrometer for measurement of the absolute DD proton spectrum from which yield and ρR are determined in thin-shell inertial-confinement-fusion implosions

    SciTech Connect

    Rosenberg, M. J. Zylstra, A. B.; Frenje, J. A.; Rinderknecht, H. G.; Gatu Johnson, M.; Waugh, C. J.; Séguin, F. H.; Sio, H.; Sinenian, N.; Li, C. K.; Petrasso, R. D.; Glebov, V. Yu.; Hohenberger, M.; Stoeckl, C.; Sangster, T. C.; Yeamans, C. B.; LePape, S.; Mackinnon, A. J.; Bionta, R. M.; Talison, B.; and others

    2014-10-01

    A compact, step range filter proton spectrometer has been developed for the measurement of the absolute DD proton spectrum, from which yield and areal density (ρR) are inferred for deuterium-filled thin-shell inertial confinement fusion implosions. This spectrometer, which is based on tantalum step-range filters, is sensitive to protons in the energy range 1-9 MeV and can be used to measure proton spectra at mean energies of ~1-3 MeV. It has been developed and implemented using a linear accelerator and applied to experiments at the OMEGA laser facility and the National Ignition Facility (NIF). Modeling of the proton slowing in the filters is necessary to construct the spectrum, and the yield and energy uncertainties are ±<10% in yield and ±120 keV, respectively. This spectrometer can be used for in situ calibration of DD-neutron yield diagnostics at the NIF.

  12. A compact proton spectrometer for measurement of the absolute DD proton spectrum from which yield and pR are determined in thin-shell inertial-confinement-fusion implosions

    SciTech Connect

    Rosenberg, M. J.; Zylstra, A. B.; Frenje, J. A.; Rinderknecht, H. G.; Gatu Johnson, M.; Waugh, C. J.; Seguin, F. H.; Sio, H.; Sinenian, N.; Li, C. K.; Petrasso, R. D.; Glebov, V. Yu.; Hohenberger, M.; Stoeckl, C.; Sangster, T. C.; Yeamans, C. B.; LePape, S.; Mackinnon, A. J.; Bionta, R. M.; Talison, B.; Casey, D. T.; Landen, O. L.; Moran, M. J.; Zacharias, R. A.; Kilkenny, J. D.; Nikroo, A.

    2014-10-10

    A compact, step range filter proton spectrometer has been developed for the measurement of the absolute DD proton spectrum, from which yield and areal density (ρR) are inferred for deuterium-filled thin-shell inertial confinement fusion implosions. This spectrometer, which is based on tantalum step-range filters, is sensitive to protons in the energy range 1-9 MeV and can be used to measure proton spectra at mean energies of ~1-3 MeV. It has been developed and implemented using a linear accelerator and applied to experiments at the OMEGA laser facility and the National Ignition Facility (NIF). Modeling of the proton slowing in the filters is necessary to construct the spectrum, and the yield and energy uncertainties are ±<10% in yield and ±120 keV, respectively. This spectrometer can be used for in situ calibration of DD-neutron yield diagnostics at the NIF

  13. A temperature oscillation instrument to determine pyroelectric properties of materials at low frequencies: Towards elimination of lock-in methods.

    PubMed

    Khanbareh, H; Schelen, J B J; van der Zwaag, S; Groen, W A

    2015-10-01

    Pyroelectric properties of materials can be accurately determined by applying a new digital signal processing method on the discrete sampled data obtained with a temperature oscillation technique. The pyroelectric coefficient is calculated from the component of the generated current 90° out of phase with respect to the sinusoidal temperature wave. The novelty of the proposed approach lies in the signal analysis procedure which implements a simple Fast Fourier transform that filters residual noise through convolution, and calculates the phase difference between the peaks of the temperature and current waves. The new idea requires relatively simple hardware and enables very accurate measurement of the pyroelectric coefficient of materials at ultra low frequencies, 1-250 mHz, without using costly lock-in amplifiers. PMID:26520988

  14. A temperature oscillation instrument to determine pyroelectric properties of materials at low frequencies: Towards elimination of lock-in methods

    NASA Astrophysics Data System (ADS)

    Khanbareh, H.; Schelen, J. B. J.; van der Zwaag, S.; Groen, W. A.

    2015-10-01

    Pyroelectric properties of materials can be accurately determined by applying a new digital signal processing method on the discrete sampled data obtained with a temperature oscillation technique. The pyroelectric coefficient is calculated from the component of the generated current 90∘ out of phase with respect to the sinusoidal temperature wave. The novelty of the proposed approach lies in the signal analysis procedure which implements a simple Fast Fourier transform that filters residual noise through convolution, and calculates the phase difference between the peaks of the temperature and current waves. The new idea requires relatively simple hardware and enables very accurate measurement of the pyroelectric coefficient of materials at ultra low frequencies, 1-250 mHz, without using costly lock-in amplifiers.

  15. Determination of lateral-stability derivatives and transfer-function coefficients from frequency-response data for lateral motions

    NASA Technical Reports Server (NTRS)

    Donegan, James J; Robinson, Samuel W , Jr; Gates, Ordway, B , jr

    1955-01-01

    A method is presented for determining the lateral-stability derivatives, transfer-function coefficients, and the modes for lateral motion from frequency-response data for a rigid aircraft. The method is based on the application of the vector technique to the equations of lateral motion, so that the three equations of lateral motion can be separated into six equations. The method of least squares is then applied to the data for each of these equations to yield the coefficients of the equations of lateral motion from which the lateral-stability derivatives and lateral transfer-function coefficients are computed. Two numerical examples are given to demonstrate the use of the method.

  16. RAPID COMMUNICATION: A novel time frequency-based 3D Lissajous figure method and its application to the determination of oxygen saturation from the photoplethysmogram

    NASA Astrophysics Data System (ADS)

    Addison, Paul S.; Watson, James N.

    2004-11-01

    We present a novel time-frequency method for the measurement of oxygen saturation using the photoplethysmogram (PPG) signals from a standard pulse oximeter machine. The method utilizes the time-frequency transformation of the red and infrared PPGs to derive a 3D Lissajous figure. By selecting the optimal Lissajous, the method provides an inherently robust basis for the determination of oxygen saturation as regions of the time-frequency plane where high- and low-frequency signal artefacts are to be found are automatically avoided.

  17. Longitudinal study of the in vivo hprt mutant frequency in human T-lymphocytes as determined by a cell cloning assay

    SciTech Connect

    O'Neill, J.P.; Sullivan, L.M.; Booker, J.K.; Pornelos, B.S.; Falta, M.T.; Greene, C.J.; Albertini, R.J. )

    1989-01-01

    The in vivo frequency of mutants resulting from mutation at the hprt locus in human T-lymphocytes can be determined by a cloning assay. This assay quantifies the frequency of 6-thioguanine-resistant (TG{sup r}) T-cells through growth of colonies in 96-well microtiter dishes. The reproducibility of the TG{sup r} mutant frequency values has now been assessed in a longitudinal study of six individuals employing 4-5 blood samples over a 26-37 week time period. Cloning assays were performed with both fresh and cryopreserved cell samples. No significant differences were found among the mutant frequency values for multiple samples from each individual with both fresh and cryopreserved cell samples. These results demonstrate the reproducibility of this cloning assay for in vivo mutant frequency determinations in human T-lymphocytes.

  18. Mapping with MAV: Experimental Study on the Contribution of Absolute and Relative Aerial Position Control

    NASA Astrophysics Data System (ADS)

    Skaloud, J.; Rehak, M.; Lichti, D.

    2014-03-01

    This study highlights the benefit of precise aerial position control in the context of mapping using frame-based imagery taken by small UAVs. We execute several flights with a custom Micro Aerial Vehicle (MAV) octocopter over a small calibration field equipped with 90 signalized targets and 25 ground control points. The octocopter carries a consumer grade RGB camera, modified to insure precise GPS time stamping of each exposure, as well as a multi-frequency/constellation GNSS receiver. The GNSS antenna and camera are rigidly mounted together on a one-axis gimbal that allows control of the obliquity of the captured imagery. The presented experiments focus on including absolute and relative aerial control. We confirm practically that both approaches are very effective: the absolute control allows omission of ground control points while the relative requires only a minimum number of control points. Indeed, the latter method represents an attractive alternative in the context of MAVs for two reasons. First, the procedure is somewhat simplified (e.g. the lever-arm between the camera perspective and antenna phase centers does not need to be determined) and, second, its principle allows employing a single-frequency antenna and carrier-phase GNSS receiver. This reduces the cost of the system as well as the payload, which in turn increases the flying time.

  19. Absolute and relative intrasession reliability of surface EMG variables for voluntary precise forearm movements.

    PubMed

    Carius, Daniel; Kugler, Patrick; Kuhwald, Hans-Marten; Wollny, Rainer

    2015-12-01

    The reliability of surface electromyography (EMG) derived parameters is of high importance, but there is distinct lack of studies concerning the reliability during dynamic contractions. Especially Amplitude, Fourier and Wavelet parameter in conjunction have not been tested so far. The interpretation of the EMG variables might be difficult because the movement itself introduces additional factors that affect its characteristics. The aim of this study was to determine the relative and absolute intrasession reliability of electromyographic (EMG) variables of selected arm muscles during concurrent precise elbow extension/flexion movements at different force levels and movement speed. Participants (all-male: n = 17, range 20-32 years) were asked to adapt to a gross-motor visuomotor tracking task (elbow extension/flexion movement) using a custom-built lever arm apparatus. After sufficient adaptation surface electromyography was used to record the electrical activity of mm. biceps brachii, brachioradialis and triceps brachii, and the signal amplitude (RMS [μV]) and the mean frequency of the power spectrum (MNF [Hz]) were computed. Additionally Wavelet analysis was used. Relative reproducibility (intraclass correlation) for signal amplitude, mean frequency of the power spectrum and Wavelet intensity during dynamic contractions was fair to good, independent of force level and movement speed (ICC = 0.71-0.98). The amount of absolute intrasession reliability (coefficient of variation) of EMG variables depends on muscle and force level. PMID:26391454

  20. Absolute oral bioavailability of ciprofloxacin.

    PubMed

    Drusano, G L; Standiford, H C; Plaisance, K; Forrest, A; Leslie, J; Caldwell, J

    1986-09-01

    We evaluated the absolute bioavailability of ciprofloxacin, a new quinoline carboxylic acid, in 12 healthy male volunteers. Doses of 200 mg were given to each of the volunteers in a randomized, crossover manner 1 week apart orally and as a 10-min intravenous infusion. Half-lives (mean +/- standard deviation) for the intravenous and oral administration arms were 4.2 +/- 0.77 and 4.11 +/- 0.74 h, respectively. The serum clearance rate averaged 28.5 +/- 4.7 liters/h per 1.73 m2 for the intravenous administration arm. The renal clearance rate accounted for approximately 60% of the corresponding serum clearance rate and was 16.9 +/- 3.0 liters/h per 1.73 m2 for the intravenous arm and 17.0 +/- 2.86 liters/h per 1.73 m2 for the oral administration arm. Absorption was rapid, with peak concentrations in serum occurring at 0.71 +/- 0.15 h. Bioavailability, defined as the ratio of the area under the curve from 0 h to infinity for the oral to the intravenous dose, was 69 +/- 7%. We conclude that ciprofloxacin is rapidly absorbed and reliably bioavailable in these healthy volunteers. Further studies with ciprofloxacin should be undertaken in target patient populations under actual clinical circumstances. PMID:3777908

  1. Unique determination of the -CN group tilt angle in Langmuir monolayers using sum-frequency polarization null angle and phase

    SciTech Connect

    Velarde Ruiz Esparza, Luis A.; Wang, Hongfei

    2013-10-14

    The relative phase and amplitude ratio between the ssp and ppp polarization combinations of the vibrational sum-frequency generation (SFG) response can be uniquely and accurately determined by the polarization null angle (PNA) method. In this report we show that PNA measurements of the -CN vibration in the 4-n pentyl-4'-cyanoterphenyl (5CT) Langmuir monolayer at the air/water interface yields ssp and ppp response of the same phase, while those in the 4-n-octyl-4'cyanobiphenyl (8CB) Langmuir monolayer have the opposite phase. Accordingly, the -CN group in the 5CT monolayer is tilted around 25+/-2 from the interface normal, while that in the 8CB is tilted around 57+/-2, consistent with the significant differences in the phase diagrams and hydrogen bonding SFG spectra of the two Langmuir monolayers as reported in the literature. These results also demonstrate that in SFG studies the relative phase information of the different polarization combinations, especially for the ssp and ppp, is important in the unique determination of the tilt angle and conformation of a molecular group at the interface.

  2. Absolute Instability in Coupled-Cavity TWTs

    NASA Astrophysics Data System (ADS)

    Hung, D. M. H.; Rittersdorf, I. M.; Zhang, Peng; Lau, Y. Y.; Simon, D. H.; Gilgenbach, R. M.; Chernin, D.; Antonsen, T. M., Jr.

    2014-10-01

    This paper will present results of our analysis of absolute instability in a coupled-cavity traveling wave tube (TWT). The structure mode at the lower and upper band edges are respectively approximated by a hyperbola in the (omega, k) plane. When the Briggs-Bers criterion is applied, a threshold current for onset of absolute instability is observed at the upper band edge, but not the lower band edge. The nonexistence of absolute instability at the lower band edge is mathematically similar to the nonexistence of absolute instability that we recently demonstrated for a dielectric TWT. The existence of absolute instability at the upper band edge is mathematically similar to the existence of absolute instability in a gyroton traveling wave amplifier. These interesting observations will be discussed, and the practical implications will be explored. This work was supported by AFOSR, ONR, and L-3 Communications Electron Devices.

  3. Absolute calibration of Landsat instruments using the moon.

    USGS Publications Warehouse

    Kieffer, H.H.; Wildey, R.L.

    1985-01-01

    A lunar observation by Landsat could provide improved radiometric and geometric calibration of both the Thematic Mapper and the Multispectral Scanner in terms of absolute radiometry, determination of the modulation transfer function, and sensitivity to scattered light. A pitch of the spacecraft would be required. -Authors

  4. Absolute configurations of zingiberenols isolated from ginger (Zingiber officinale) rhizomes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The sesquiterpene alcohol zingiberenol, or 1,10-bisaboladien-3-ol, was isolated some time ago from ginger, Zingiber officinale, rhizomes, but its absolute configuration had not been determined. With three chiral centers present in the molecule, zingiberenol can exist in eight stereoisomeric forms. ...

  5. The 1994 international transatlantic two-way satellite time and frequency transfer experiment: Preliminary results

    NASA Technical Reports Server (NTRS)

    Deyoung, James A.; Klepczynski, William J.; Mckinley, Angela Davis; Powell, William M.; Mai, Phu V.; Hetzel, P.; Bauch, A.; Davis, J. A.; Pearce, P. R.; Baumont, Francoise S.

    1995-01-01

    The international transatlantic time and frequency transfer experiment was designed by participating laboratories and has been implemented during 1994 to test the international communications path involving a large number of transmitting stations. This paper will present empirically determined clock and time scale differences, time and frequency domain instabilities, and a representative power spectral density analysis. The experiments by the method of co-location which will allow absolute calibration of the participating laboratories have been performed. Absolute time differences and accuracy levels of this experiment will be assessed in the near future.

  6. Absolute photon-flux measurements in the vacuum ultraviolet

    NASA Technical Reports Server (NTRS)

    Samson, J. A. R.; Haddad, G. N.

    1974-01-01

    Absolute photon-flux measurements in the vacuum ultraviolet have extended to short wavelengths by use of rare-gas ionization chambers. The technique involves the measurement of the ion current as a function of the gas pressure in the ion chamber. The true value of the ion current, and hence the absolute photon flux, is obtained by extrapolating the ion current to zero gas pressure. Examples are given at 162 and 266 A. The short-wavelength limit is determined only by the sensitivity of the current-measuring apparatus and by present knowledge of the photoionization processes that occur in the rate gases.

  7. Notes on Van der Meer scan for absolute luminosity measurement

    NASA Astrophysics Data System (ADS)

    Balagura, Vladislav

    2011-10-01

    The absolute luminosity can be measured in an accelerator by sweeping beams transversely across each other in the so-called van der Meer scan. We prove that the method can be applied in the general case of arbitrary beam directions and a separation scan plane. A simple method to develop an image of the beam in its transverse plane from spatial distributions of interaction vertexes is also proposed. From the beam images one can determine their overlap and the absolute luminosity. This provides an alternative way of the luminosity measurement during van der Meer scan.

  8. Absolute negative mobility of interacting Brownian particles

    NASA Astrophysics Data System (ADS)

    Ou, Ya-li; Hu, Cai-tian; Wu, Jian-chun; Ai, Bao-quan

    2015-12-01

    Transport of interacting Brownian particles in a periodic potential is investigated in the presence of an ac force and a dc force. From Brownian dynamic simulations, we find that both the interaction between particles and the thermal fluctuations play key roles in the absolute negative mobility (the particle noisily moves backwards against a small constant bias). When no the interaction acts, there is only one region where the absolute negative mobility occurs. In the presence of the interaction, the absolute negative mobility may appear in multiple regions. The weak interaction can be helpful for the absolute negative mobility, while the strong interaction has a destructive impact on it.

  9. A compact proton spectrometer for measurement of the absolute DD proton spectrum from which yield and pR are determined in thin-shell inertial-confinement-fusion implosions

    DOE PAGESBeta

    Rosenberg, M. J.; Zylstra, A. B.; Frenje, J. A.; Rinderknecht, H. G.; Gatu Johnson, M.; Waugh, C. J.; Seguin, F. H.; Sio, H.; Sinenian, N.; Li, C. K.; et al

    2014-10-10

    A compact, step range filter proton spectrometer has been developed for the measurement of the absolute DD proton spectrum, from which yield and areal density (ρR) are inferred for deuterium-filled thin-shell inertial confinement fusion implosions. This spectrometer, which is based on tantalum step-range filters, is sensitive to protons in the energy range 1-9 MeV and can be used to measure proton spectra at mean energies of ~1-3 MeV. It has been developed and implemented using a linear accelerator and applied to experiments at the OMEGA laser facility and the National Ignition Facility (NIF). Modeling of the proton slowing in themore » filters is necessary to construct the spectrum, and the yield and energy uncertainties are ±<10% in yield and ±120 keV, respectively. This spectrometer can be used for in situ calibration of DD-neutron yield diagnostics at the NIF« less

  10. System and method for calibrating a rotary absolute position sensor

    NASA Technical Reports Server (NTRS)

    Davis, Donald R. (Inventor); Permenter, Frank Noble (Inventor); Radford, Nicolaus A (Inventor)

    2012-01-01

    A system includes a rotary device, a rotary absolute position (RAP) sensor generating encoded pairs of voltage signals describing positional data of the rotary device, a host machine, and an algorithm. The algorithm calculates calibration parameters usable to determine an absolute position of the rotary device using the encoded pairs, and is adapted for linearly-mapping an ellipse defined by the encoded pairs to thereby calculate the calibration parameters. A method of calibrating the RAP sensor includes measuring the rotary position as encoded pairs of voltage signals, linearly-mapping an ellipse defined by the encoded pairs to thereby calculate the calibration parameters, and calculating an absolute position of the rotary device using the calibration parameters. The calibration parameters include a positive definite matrix (A) and a center point (q) of the ellipse. The voltage signals may include an encoded sine and cosine of a rotary angle of the rotary device.

  11. Absolute and Convective Instability in Fluid-Conveying Flexible Pipes

    NASA Astrophysics Data System (ADS)

    de Langre, E.; Ouvrard, A. E.

    1998-11-01

    The effect of internal plug flow on the lateral stability of fluid conveying flexible pipes is investigated by determining the absolute/convective nature of the instability from the analytically derived linear dispersion relation. The fluid-structure interaction is modeled following the work of Gregory and Paidoussis (1966). The different domains of stability, convective instability, and absolute instability are explicitly derived in parameter space. The effect of flow velocity, mass ratio between the fluid and the structure, stiffness of the elastic foundation and axial tension is considered. Absolute instability prevails over a wide range of parameters. Convective instability only takes place at very high mass ratio, small stiffness and small axial tension. Relation is made with previous work of Brazier-Smith & Scott (1984) and Crighton (1991), considered here as a short wave approximation.

  12. Simple method for absolute calibration of geophones, seismometers, and other inertial vibration sensors

    SciTech Connect

    Kann, Frank van; Winterflood, John

    2005-03-01

    A simple but powerful method is presented for calibrating geophones, seismometers, and other inertial vibration sensors, including passive accelerometers. The method requires no cumbersome or expensive fixtures such as shaker platforms and can be performed using a standard instrument commonly available in the field. An absolute calibration is obtained using the reciprocity property of the device, based on the standard mathematical model for such inertial sensors. It requires only simple electrical measurement of the impedance of the sensor as a function of frequency to determine the parameters of the model and hence the sensitivity function. The method is particularly convenient if one of these parameters, namely the suspended mass is known. In this case, no additional mechanical apparatus is required and only a single set of impedance measurements yields the desired calibration function. Moreover, this measurement can be made with the device in situ. However, the novel and most powerful aspect of the method is its ability to accurately determine the effective suspended mass. For this, the impedance measurement is made with the device hanging from a simple spring or flexible cord (depending on the orientation of its sensitive axis). To complete the calibration, the device is weighed to determine its total mass. All the required calibration parameters, including the suspended mass, are then determined from a least-squares fit to the impedance as a function of frequency. A demonstration using both a 4.5 Hz geophone and a 1 Hz seismometer shows that the method can yield accurate absolute calibrations with an error of 0.1% or better, assuming no a priori knowledge of any parameters.

  13. Toward automatic phenotyping of retinal images from genetically determined mono- and dizygotic twins using amplitude modulation-frequency modulation methods

    NASA Astrophysics Data System (ADS)

    Soliz, P.; Davis, B.; Murray, V.; Pattichis, M.; Barriga, S.; Russell, S.

    2010-03-01

    This paper presents an image processing technique for automatically categorize age-related macular degeneration (AMD) phenotypes from retinal images. Ultimately, an automated approach will be much more precise and consistent in phenotyping of retinal diseases, such as AMD. We have applied the automated phenotyping to retina images from a cohort of mono- and dizygotic twins. The application of this technology will allow one to perform more quantitative studies that will lead to a better understanding of the genetic and environmental factors associated with diseases such as AMD. A method for classifying retinal images based on features derived from the application of amplitude-modulation frequency-modulation (AM-FM) methods is presented. Retinal images from identical and fraternal twins who presented with AMD were processed to determine whether AM-FM could be used to differentiate between the two types of twins. Results of the automatic classifier agreed with the findings of other researchers in explaining the variation of the disease between the related twins. AM-FM features classified 72% of the twins correctly. Visual grading found that genetics could explain between 46% and 71% of the variance.

  14. Determination of the magnetocrystalline anisotropy constant from the frequency dependence of the specific absorption rate in a frozen ferrofluid

    NASA Astrophysics Data System (ADS)

    Mosher, Nathaniel; Perkins-Harbin, Emily; Aho, Brandon; Wang, Lihua; Kumon, Ronald; Rablau, Corneliu; Vaishnava, Prem; Tackett, Ronald; Therapeutic Biomaterials Group Team

    2015-03-01

    Colloidal suspensions of superparamagnetic nanoparticles, known as ferrofluids, are promising candidates for the mediation of magnetic fluid hyperthermia (MFH). In such materials, the dissipation of heat occurs as a result of the relaxation of the particles in an applied ac magnetic field via the Brownian and Neel mechanisms. In order to isolate and study the role of the Neel mechanism in this process, the sample can be frozen, using liquid nitrogen, in order to suppress the Brownian relaxation. In this experiment, dextran-coated Fe3O4 nanoparticles synthesized via co-precipitation and characterized via transmission electron microscopy and dc magnetization are used as MFH mediators over the temperature range between -70 °C to -10 °C (Brownian-suppressed state). Heating the nanoparticles using ac magnetic field (amplitude ~300 Oe), the frequency dependence of the specific absorption rate (SAR) is calculated between 150 kHz and 350 kHz and used to determine the magnetocrystalline anisotropy of the sample. We would like to thank Fluxtrol, Inc. for their help with this project

  15. Determining the frequency of pathogenic germline variants from exome sequencing in patients with castrate-resistant prostate cancer

    PubMed Central

    Hart, Steven N; Ellingson, Marissa S; Schahl, Kim; Vedell, Peter T; Carlson, Rachel E; Sinnwell, Jason P; Barman, Poulami; Sicotte, Hugues; Eckel-Passow, Jeanette E; Wang, Liguo; Kalari, Krishna R; Qin, Rui; Kruisselbrink, Teresa M; Jimenez, Rafael E; Bryce, Alan H; Tan, Winston; Weinshilboum, Richard; Wang, Liewei; Kohli, Manish

    2016-01-01

    Objectives To determine the frequency of pathogenic inherited mutations in 157 select genes from patients with metastatic castrate-resistant prostate cancer (mCRPC). Design Observational. Setting Multisite US-based cohort. Participants Seventy-one adult male patients with histological confirmation of prostate cancer, and had progressive disease while on androgen deprivation therapy. Results Twelve patients (17.4%) showed evidence of carrying pathogenic or likely pathogenic germline variants in the ATM, ATR, BRCA2, FANCL, MSR1, MUTYH, RB1, TSHR and WRN genes. All but one patient opted in to receive clinically actionable results at the time of study initiation. We also found that pathogenic germline BRCA2 variants appear to be enriched in mCRPC compared to familial prostate cancers. Conclusions Pathogenic variants in cancer-susceptibility genes are frequently observed in patients with mCRPC. A substantial proportion of patients with mCRPC or their family members would derive clinical utility from mutation screening. Trial registration number NCT01953640; Results. PMID:27084275

  16. Balance between cell−substrate adhesion and myosin contraction determines the frequency of motility initiation in fish keratocytes

    PubMed Central

    Barnhart, Erin; Lee, Kun-Chun; Allen, Greg M.; Theriot, Julie A.; Mogilner, Alex

    2015-01-01

    Cells are dynamic systems capable of spontaneously switching among stable states. One striking example of this is spontaneous symmetry breaking and motility initiation in fish epithelial keratocytes. Although the biochemical and mechanical mechanisms that control steady-state migration in these cells have been well characterized, the mechanisms underlying symmetry breaking are less well understood. In this work, we have combined experimental manipulations of cell−substrate adhesion strength and myosin activity, traction force measurements, and mathematical modeling to develop a comprehensive mechanical model for symmetry breaking and motility initiation in fish epithelial keratocytes. Our results suggest that stochastic fluctuations in adhesion strength and myosin localization drive actin network flow rates in the prospective cell rear above a critical threshold. Above this threshold, high actin flow rates induce a nonlinear switch in adhesion strength, locally switching adhesions from gripping to slipping and further accelerating actin flow in the prospective cell rear, resulting in rear retraction and motility initiation. We further show, both experimentally and with model simulations, that the global levels of adhesion strength and myosin activity control the stability of the stationary state: The frequency of symmetry breaking decreases with increasing adhesion strength and increases with increasing myosin contraction. Thus, the relative strengths of two opposing mechanical forces—contractility and cell−substrate adhesion—determine the likelihood of spontaneous symmetry breaking and motility initiation. PMID:25848042

  17. Inequalities, Absolute Value, and Logical Connectives.

    ERIC Educational Resources Information Center

    Parish, Charles R.

    1992-01-01

    Presents an approach to the concept of absolute value that alleviates students' problems with the traditional definition and the use of logical connectives in solving related problems. Uses a model that maps numbers from a horizontal number line to a vertical ray originating from the origin. Provides examples solving absolute value equations and…

  18. Absolute optical metrology : nanometers to kilometers

    NASA Technical Reports Server (NTRS)

    Dubovitsky, Serge; Lay, O. P.; Peters, R. D.; Liebe, C. C.

    2005-01-01

    We provide and overview of the developments in the field of high-accuracy absolute optical metrology with emphasis on space-based applications. Specific work on the Modulation Sideband Technology for Absolute Ranging (MSTAR) sensor is described along with novel applications of the sensor.

  19. Introducing the Mean Absolute Deviation "Effect" Size

    ERIC Educational Resources Information Center

    Gorard, Stephen

    2015-01-01

    This paper revisits the use of effect sizes in the analysis of experimental and similar results, and reminds readers of the relative advantages of the mean absolute deviation as a measure of variation, as opposed to the more complex standard deviation. The mean absolute deviation is easier to use and understand, and more tolerant of extreme…

  20. Investigating Absolute Value: A Real World Application

    ERIC Educational Resources Information Center

    Kidd, Margaret; Pagni, David

    2009-01-01

    Making connections between various representations is important in mathematics. In this article, the authors discuss the numeric, algebraic, and graphical representations of sums of absolute values of linear functions. The initial explanations are accessible to all students who have experience graphing and who understand that absolute value simply…

  1. Absolute Income, Relative Income, and Happiness

    ERIC Educational Resources Information Center

    Ball, Richard; Chernova, Kateryna

    2008-01-01

    This paper uses data from the World Values Survey to investigate how an individual's self-reported happiness is related to (i) the level of her income in absolute terms, and (ii) the level of her income relative to other people in her country. The main findings are that (i) both absolute and relative income are positively and significantly…

  2. Exploiting knowledge of jump-up and jump-down frequencies to determine the parameters of a Duffing oscillator

    NASA Astrophysics Data System (ADS)

    Ramlan, Roszaidi; Brennan, Michael J.; Kovacic, Ivana; Mace, Brian R.; Burrow, Stephen G.

    2016-08-01

    This work concerns the application of certain non-linear phenomena - jump frequencies in a base-excited Duffing oscillator - to the estimation of the parameters of the system. First, approximate analytical expressions are derived for the relationships between the jump-up and jump-down frequencies, the damping ratio and the cubic stiffness coefficient. Then, experimental results, together with the results of numerical simulations, are presented to show how knowledge of these frequencies can be exploited.

  3. Validation of SNP Allele Frequencies Determined by Pooled Next-Generation Sequencing in Natural Populations of a Non-Model Plant Species

    PubMed Central

    Rellstab, Christian; Zoller, Stefan; Tedder, Andrew; Gugerli, Felix; Fischer, Martin C.

    2013-01-01

    Sequencing of pooled samples (Pool-Seq) using next-generation sequencing technologies has become increasingly popular, because it represents a rapid and cost-effective method to determine allele frequencies for single nucleotide polymorphisms (SNPs) in population pools. Validation of allele frequencies determined by Pool-Seq has been attempted using an individual genotyping approach, but these studies tend to use samples from existing model organism databases or DNA stores, and do not validate a realistic setup for sampling natural populations. Here we used pyrosequencing to validate allele frequencies determined by Pool-Seq in three natural populations of Arabidopsis halleri (Brassicaceae). The allele frequency estimates of the pooled population samples (consisting of 20 individual plant DNA samples) were determined after mapping Illumina reads to (i) the publicly available, high-quality reference genome of a closely related species (Arabidopsis thaliana) and (ii) our own de novo draft genome assembly of A. halleri. We then pyrosequenced nine selected SNPs using the same individuals from each population, resulting in a total of 540 samples. Our results show a highly significant and accurate relationship between pooled and individually determined allele frequencies, irrespective of the reference genome used. Allele frequencies differed on average by less than 4%. There was no tendency that either the Pool-Seq or the individual-based approach resulted in higher or lower estimates of allele frequencies. Moreover, the rather high coverage in the mapping to the two reference genomes, ranging from 55 to 284x, had no significant effect on the accuracy of the Pool-Seq. A resampling analysis showed that only very low coverage values (below 10-20x) would substantially reduce the precision of the method. We therefore conclude that a pooled re-sequencing approach is well suited for analyses of genetic variation in natural populations. PMID:24244686

  4. Absolute Pitch in Boreal Chickadees and Humans: Exceptions that Test a Phylogenetic Rule

    ERIC Educational Resources Information Center

    Weisman, Ronald G.; Balkwill, Laura-Lee; Hoeschele, Marisa; Moscicki, Michele K.; Bloomfield, Laurie L.; Sturdy, Christopher B.

    2010-01-01

    This research examined generality of the phylogenetic rule that birds discriminate frequency ranges more accurately than mammals. Human absolute pitch chroma possessors accurately tracked transitions between frequency ranges. Independent tests showed that they used note naming (pitch chroma) to remap the tones into ranges; neither possessors nor…

  5. Experimental Determination of Effects of Frequency and Amplitude on the Lateral Stability Derivatives for a Delta, a Swept, and Unswept Wing Oscillating in Yaw

    NASA Technical Reports Server (NTRS)

    Fisher, Lewis R

    1958-01-01

    Three wing models were oscillated in yaw about their vertical axes to determine the effects of systematic variations of frequency and amplitude of oscillation on the in-phase and out-of-phase combination lateral stability derivatives resulting from this motion. The tests were made at low speeds for a 60 degree delta wing, a 45 degree swept wing, and an unswept wing; the swept and unswept wings had aspect ratios of 4. The results indicate that large changes in the magnitude of the stability derivatives due to the variation of frequency occur at high angles of attack, particularly for the delta wing. The greatest variations of the derivatives with frequency take place for the lowest frequencies of oscillation; at the higher frequencies, the effects of frequency are smaller and the derivatives become more linear with angle of attack. Effects of amplitude of oscillation on the stability derivatives for delta wings were evident for certain high angles of attack and for the lowest frequencies of oscillation. As the frequency became high, the amplitude effects tended to disappear.

  6. Absolute calibration for a broad range single shot electron spectrometer

    SciTech Connect

    Glinec, Y.; Faure, J.; Guemnie-Tafo, A.; Malka, V.; Monard, H.; Larbre, J. P.; De Waele, V.; Marignier, J. L.; Mostafavi, M.

    2006-10-15

    This article gives a detailed description of a single shot electron spectrometer which was used to characterize electron beams produced by laser-plasma interaction. Contrary to conventional electron sources, electron beams from laser-plasma accelerators can produce a broad range of energies. Therefore, diagnosing these electron spectra requires specific attention and experimental development. Here, we provide an absolute calibration of the Lanex Kodak Fine screen on a laser-triggered radio frequency picosecond electron accelerator. The efficiency of scintillating screens irradiated by electron beams has never been investigated so far. This absolute calibration is then compared to charge measurements from an integrating current transformer for quasimonoenergetic electron spectra from laser-plasma interaction.

  7. Proposal for an absolute, atomic definition of mass

    NASA Astrophysics Data System (ADS)

    Wignall, J. W. G.

    1991-11-01

    It is proposed that the mass of a particle be defined absolutely as its de Broglie frequency, measured as the mean de Broglie wavelength of the particle when it has a mean speed (v) and Lorentz factor (gamma); the masses of systems too large to have a measurable de Broglie wavelength mean are then to be derived by specifying the usual inertial and additive properties of mass. This definition avoids the use of an arbitrary macroscopic standard such as the prototype kilogram, and, if present theory is correct, does not even require the choice of a specific particle as a mass standard. Suggestions are made as to how this absolute mass can be realized and measured at the macroscopic level and, finally, some comments are made on the effect of the new definition on the form of the equations of physics.

  8. Absolute calibration for a broad range single shot electron spectrometer

    NASA Astrophysics Data System (ADS)

    Glinec, Y.; Faure, J.; Guemnie-Tafo, A.; Malka, V.; Monard, H.; Larbre, J. P.; De Waele, V.; Marignier, J. L.; Mostafavi, M.

    2006-10-01

    This article gives a detailed description of a single shot electron spectrometer which was used to characterize electron beams produced by laser-plasma interaction. Contrary to conventional electron sources, electron beams from laser-plasma accelerators can produce a broad range of energies. Therefore, diagnosing these electron spectra requires specific attention and experimental development. Here, we provide an absolute calibration of the Lanex Kodak Fine screen on a laser-triggered radio frequency picosecond electron accelerator. The efficiency of scintillating screens irradiated by electron beams has never been investigated so far. This absolute calibration is then compared to charge measurements from an integrating current transformer for quasimonoenergetic electron spectra from laser-plasma interaction.

  9. Changing the Tune: The Structure of the Input Affects Infants' Use of Absolute and Relative Pitch

    ERIC Educational Resources Information Center

    Saffran, Jenny R.; Reeck, Karelyn; Niebuhr, Aimee; Wilson, Diana

    2005-01-01

    Sequences of notes contain several different types of pitch cues, including both absolute and relative pitch information. What factors determine which of these cues are used when learning about tone sequences? Previous research suggests that infants tend to preferentially process absolute pitch patterns in continuous tone sequences, while other…

  10. 47 CFR 64.1160 - Absolution procedures where the subscriber has not paid charges.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 3 2010-10-01 2010-10-01 false Absolution procedures where the subscriber has... Preferred Telecommunications Service Providers § 64.1160 Absolution procedures where the subscriber has not paid charges. (a) This section shall only apply after a subscriber has determined that an...

  11. Preliminary OARE absolute acceleration measurements on STS-50

    NASA Technical Reports Server (NTRS)

    Blanchard, Robert C.; Nicholson, John Y.; Ritter, James

    1993-01-01

    On-orbit Orbital Acceleration Research Experiment (OARE) data on STS-50 was examined in detail during a 2-day time period. Absolute acceleration levels were derived at the OARE location, the orbiter center-of-gravity, and at the STS-50 spacelab Crystal Growth Facility. The tri-axial OARE raw acceleration measurements (i.e., telemetered data) during the interval were filtered using a sliding trimmed mean filter in order to remove large acceleration spikes (e.g., thrusters) and reduce the noise. Twelve OARE measured biases in each acceleration channel during the 2-day interval were analyzed and applied to the filtered data. Similarly, the in situ measured x-axis scale factors in the sensor's most sensitive range were also analyzed and applied to the data. Due to equipment problem(s) on this flight, both y- and z- axis sensitive range scale factors were determined in a separate process (using the OARE maneuver data) and subsequently applied to the data. All known significant low-frequency corrections at the OARE location (i.e., both vertical and horizontal gravity-gradient, and rotational effects) were removed from the filtered data in order to produce the acceleration components at the orbiter's center-of-gravity, which are the aerodynamic signals along each body axes. Results indicate that there is a force of unknown origin being applied to the Orbiter in addition to the aerodynamic forces. The OARE instrument and all known gravitational and electromagnetic forces were reexamined, but none produce the observed effect. Thus, it is tentatively concluded that the Orbiter is creating the environment observed.

  12. Preliminary OARE absolute acceleration measurements on STS-50

    NASA Astrophysics Data System (ADS)

    Blanchard, Robert C.; Nicholson, John Y.; Ritter, James

    1993-02-01

    On-orbit Orbital Acceleration Research Experiment (OARE) data on STS-50 was examined in detail during a 2-day time period. Absolute acceleration levels were derived at the OARE location, the orbiter center-of-gravity, and at the STS-50 spacelab Crystal Growth Facility. The tri-axial OARE raw acceleration measurements (i.e., telemetered data) during the interval were filtered using a sliding trimmed mean filter in order to remove large acceleration spikes (e.g., thrusters) and reduce the noise. Twelve OARE measured biases in each acceleration channel during the 2-day interval were analyzed and applied to the filtered data. Similarly, the in situ measured x-axis scale factors in the sensor's most sensitive range were also analyzed and applied to the data. Due to equipment problem(s) on this flight, both y- and z- axis sensitive range scale factors were determined in a separate process (using the OARE maneuver data) and subsequently applied to the data. All known significant low-frequency corrections at the OARE location (i.e., both vertical and horizontal gravity-gradient, and rotational effects) were removed from the filtered data in order to produce the acceleration components at the orbiter's center-of-gravity, which are the aerodynamic signals along each body axes. Results indicate that there is a force of unknown origin being applied to the Orbiter in addition to the aerodynamic forces. The OARE instrument and all known gravitational and electromagnetic forces were reexamined, but none produce the observed effect. Thus, it is tentatively concluded that the Orbiter is creating the environment observed.

  13. Frequency ratios and the discrimination of pure tone sequences.

    PubMed

    Schellenberg, E G; Trehub, S E

    1994-10-01

    We examined the effect of frequency ratios on the discrimination of patterns of alternating pure tones (ABABA). Listeners heard a repeating pattern presented in transposition (same frequency ratios between successive tones, different absolute frequencies) and were required to indicate when the pattern changed (different frequency ratios and absolute frequencies). Changes from patterns with simple frequency ratios to those with more complex ratios were more readily detected than were changes from complex ratios to simpler ratios. PMID:7984402

  14. Absolute optical instruments without spherical symmetry

    NASA Astrophysics Data System (ADS)

    Tyc, Tomáš; Dao, H. L.; Danner, Aaron J.

    2015-11-01

    Until now, the known set of absolute optical instruments has been limited to those containing high levels of symmetry. Here, we demonstrate a method of mathematically constructing refractive index profiles that result in asymmetric absolute optical instruments. The method is based on the analogy between geometrical optics and classical mechanics and employs Lagrangians that separate in Cartesian coordinates. In addition, our method can be used to construct the index profiles of most previously known absolute optical instruments, as well as infinitely many different ones.

  15. Frequency Standards and Metrology

    NASA Astrophysics Data System (ADS)

    Maleki, Lute

    2009-04-01

    Preface / Lute Maleki -- Symposium history / Jacques Vanier -- Symposium photos -- pt. I. Fundamental physics. Variation of fundamental constants from the big bang to atomic clocks: theory and observations (Invited) / V. V. Flambaum and J. C. Berengut. Alpha-dot or not: comparison of two single atom optical clocks (Invited) / T. Rosenband ... [et al.]. Variation of the fine-structure constant and laser cooling of atomic dysprosium (Invited) / N. A. Leefer ... [et al.]. Measurement of short range forces using cold atoms (Invited) / F. Pereira Dos Santos ... [et al.]. Atom interferometry experiments in fundamental physics (Invited) / S. W. Chiow ... [et al.]. Space science applications of frequency standards and metrology (Invited) / M. Tinto -- pt. II. Frequency & metrology. Quantum metrology with lattice-confined ultracold Sr atoms (Invited) / A. D. Ludlow ... [et al.]. LNE-SYRTE clock ensemble: new [symbol]Rb hyperfine frequency measurement - spectroscopy of [symbol]Hg optical clock transition (Invited) / M. Petersen ... [et al.]. Precise measurements of S-wave scattering phase shifts with a juggling atomic clock (Invited) / S. Gensemer ... [et al.]. Absolute frequency measurement of the [symbol] clock transition (Invited) / M. Chwalla ... [et al.]. The semiclassical stochastic-field/atom interaction problem (Invited) / J. Camparo. Phase and frequency noise metrology (Invited) / E. Rubiola ... [et al.]. Optical spectroscopy of atomic hydrogen for an improved determination of the Rydberg constant / J. L. Flowers ... [et al.] -- pt. III. Clock applications in space. Recent progress on the ACES mission (Invited) / L. Cacciapuoti and C. Salomon. The SAGAS mission (Invited) / P. Wolf. Small mercury microwave ion clock for navigation and radioScience (Invited) / J. D. Prestage ... [et al.]. Astro-comb: revolutionizing precision spectroscopy in astrophysics (Invited) / C. E. Kramer ... [et al.]. High frequency very long baseline interferometry: frequency standards and

  16. Absolute surface energy for zincblende semiconductors

    NASA Astrophysics Data System (ADS)

    Zhang, S. B.; Wei, Su-Huai

    2003-03-01

    Recent advance in nanosciences requires the determination of surface (or facet) energy of semiconductors, which is often difficult due to the polar nature of some of the most important surfaces such as the (111)A/(111)B surfaces. Several approaches have been developed in the past [1-3] to deal with the problem but an unambiguous division of the polar surface energies is yet to come [2]. Here we show that an accurate division is indeed possible for the zincblende semiconductors and will present the results for GaAs, ZnSe, and CuInSe2 [4], respectively. A general trend emerges, relating the absolute surface energy to the ionicity of the bulk materials. [1] N. Chetty and R. M. Martin, Phys. Rev. B 45, 6074 (1992). [2] N. Moll, et al., Phys. Rev. B 54, 8844 (1996). [3] S. Mankefors, Phys. Rev. B 59, 13151 (1999). [4] S. B. Zhang and S.-H. Wei, Phys. Rev. B 65, 081402 (2002).

  17. GNSS Absolute Antenna Calibration at the National Geodetic Survey

    NASA Astrophysics Data System (ADS)

    Mader, G. L.; Bilich, A. L.; Geoghegan, C.

    2011-12-01

    Geodetic GNSS applications routinely demand millimeter precision and extremely high levels of accuracy. To achieve these accuracies, measurement and instrument biases at the centimeter to millimeter level must be understood. One of these biases is the antenna phase center, the apparent point of signal reception for a GNSS antenna. It has been well established that phase center patterns differ between antenna models and manufacturers; additional research suggests that the addition of a radome or the choice of antenna mount can significantly alter those a priori phase center patterns. For the more demanding GNSS positioning applications and especially in cases of mixed-antenna networks, it is all the more important to know antenna phase center variations as a function of both elevation and azimuth in the antenna reference frame and incorporate these models into analysis software. To help meet the needs of the high-precision GNSS community, the National Geodetic Survey (NGS) now operates an absolute antenna calibration facility. Located in Corbin, Virginia, this facility uses field measurements and actual GNSS satellite signals to quantitatively determine the carrier phase advance/delay introduced by the antenna element. The NGS facility was built to serve traditional NGS constituents such as the surveying and geodesy communities, however calibration services are open and available to all GNSS users as the calibration schedule permits. All phase center patterns computed by this facility will be publicly available and disseminated in both the ANTEX and NGS formats. We describe the NGS calibration facility, and discuss the observation models and strategy currently used to generate NGS absolute calibrations. We demonstrate that NGS absolute phase center variation (PCV) patterns are consistent with published values determined by other absolute antenna calibration facilities, and compare absolute calibrations to the traditional NGS relative calibrations.

  18. Using noncontact AFM frequency shifts to determine stereocilia bundle stiffness and tension in the developing cochlear sensory epithelium

    NASA Astrophysics Data System (ADS)

    Chadwick, Richard S.; Cartagena-Rivera, Alexander X.

    2015-12-01

    Measurement of frequency shifts of cantilevers having an attached microsphere oscillating at acoustic frequencies can be used to assess mechanical properties of cochlear structures. The method has already been reported for measuring elastic and viscous properties of the tectorial membrane. We describe here how the method can be used to examine other cochlear structures. Theory and formulas for relating hair bundle stiffness and tension in the developing cochlear sensory epithelium to measured frequency shifts are given to estimate the expected frequency shifts and show feasibility of the measurements. We show through a molecular model of myosin II located along the edges of confluent hexagons that myosin contractile forces are balanced by isotropic tension in the developing confluent sheet of cells.

  19. Absolute magnitudes of trans-neptunian objects

    NASA Astrophysics Data System (ADS)

    Duffard, R.; Alvarez-candal, A.; Pinilla-Alonso, N.; Ortiz, J. L.; Morales, N.; Santos-Sanz, P.; Thirouin, A.

    2015-10-01

    Accurate measurements of diameters of trans- Neptunian objects are extremely complicated to obtain. Radiomatric techniques applied to thermal measurements can provide good results, but precise absolute magnitudes are needed to constrain diameters and albedos. Our objective is to measure accurate absolute magnitudes for a sample of trans- Neptunian objects, many of which have been observed, and modelled, by the "TNOs are cool" team, one of Herschel Space Observatory key projects grantes with ~ 400 hours of observing time. We observed 56 objects in filters V and R, if possible. These data, along with data available in the literature, was used to obtain phase curves and to measure absolute magnitudes by assuming a linear trend of the phase curves and considering magnitude variability due to rotational light-curve. In total we obtained 234 new magnitudes for the 56 objects, 6 of them with no reported previous measurements. Including the data from the literature we report a total of 109 absolute magnitudes.

  20. A New Gimmick for Assigning Absolute Configuration.

    ERIC Educational Resources Information Center

    Ayorinde, F. O.

    1983-01-01

    A five-step procedure is provided to help students in making the assignment absolute configuration less bothersome. Examples for both single (2-butanol) and multi-chiral carbon (3-chloro-2-butanol) molecules are included. (JN)

  1. Absolute Radiometer for Reproducing the Solar Irradiance Unit

    NASA Astrophysics Data System (ADS)

    Sapritskii, V. I.; Pavlovich, M. N.

    1989-01-01

    A high-precision absolute radiometer with a thermally stabilized cavity as receiving element has been designed for use in solar irradiance measurements. The State Special Standard of the Solar Irradiance Unit has been built on the basis of the developed absolute radiometer. The Standard also includes the sun tracking system and the system for automatic thermal stabilization and information processing, comprising a built-in microcalculator which calculates the irradiance according to the input program. During metrological certification of the Standard, main error sources have been analysed and the non-excluded systematic and accidental errors of the irradiance-unit realization have been determined. The total error of the Standard does not exceed 0.3%. Beginning in 1984 the Standard has been taking part in a comparison with the Å 212 pyrheliometer and other Soviet and foreign standards. In 1986 it took part in the international comparison of absolute radiometers and standard pyrheliometers of socialist countries. The results of the comparisons proved the high metrological quality of this Standard based on an absolute radiometer.

  2. Assignment of absolute stereochemistry by computation of optical rotation angles

    NASA Astrophysics Data System (ADS)

    Kondru, Rama Krishna

    We have developed simple wire and molecular orbital models to qualitatively and quantitatively understand optical rotation angles of molecules. We reported the first ab initio theoretical approach to determine the absolute stereochemistry of a complex natural product by calculating molar rotation angles, [M]D. We applied this method for an unambiguous assignment of the absolute stereochemistry of the hennoxazole A. A protocol analogous to population analysis was devised to analyze atomic contributions to the rotation angles for oxiranes, orthoesters, and other organic compounds. The molar rotations for an indoline, an indonone, menthol and menthone were calculated using ab inito methods and compared with experimental values. We reported the first prediction of the absolute configuration of a natural product, i.e. an a priori assignment of the relative and absolute stereochemistry of pitiamide A. Furthermore, we described a strategy that may help to establish structure-function relations for rotation angles by visualizing the electric and magnetic-field perturbations to a molecule's molecular orbitals.

  3. Absolute Calibration of the Radio Astronomy Flux Density Scale at 22 to 43 GHz Using Planck

    NASA Astrophysics Data System (ADS)

    Partridge, B.; López-Caniego, M.; Perley, R. A.; Stevens, J.; Butler, B. J.; Rocha, G.; Walter, B.; Zacchei, A.

    2016-04-01

    The Planck mission detected thousands of extragalactic radio sources at frequencies from 28 to 857 GHz. Planck's calibration is absolute (in the sense that it is based on the satellite’s annual motion around the Sun and the temperature of the cosmic microwave background), and its beams are well characterized at sub-percent levels. Thus, Planck's flux density measurements of compact sources are absolute in the same sense. We have made coordinated Very Large Array (VLA) and Australia Telescope Compact Array (ATCA) observations of 65 strong, unresolved Planck sources in order to transfer Planck's calibration to ground-based instruments at 22, 28, and 43 GHz. The results are compared to microwave flux density scales currently based on planetary observations. Despite the scatter introduced by the variability of many of the sources, the flux density scales are determined to 1%–2% accuracy. At 28 GHz, the flux density scale used by the VLA runs 2%–3% ± 1.0% below Planck values with an uncertainty of +/- 1.0%; at 43 GHz, the discrepancy increases to 5%–6% ± 1.4% for both ATCA and the VLA.

  4. Method of differential-phase/absolute-amplitude QAM

    DOEpatents

    Dimsdle, Jeffrey William

    2007-07-03

    A method of quadrature amplitude modulation involving encoding phase differentially and amplitude absolutely, allowing for a high data rate and spectral efficiency in data transmission and other communication applications, and allowing for amplitude scaling to facilitate data recovery; amplitude scale tracking to track-out rapid and severe scale variations and facilitate successful demodulation and data retrieval; 2.sup.N power carrier recovery; incoherent demodulation where coherent carrier recovery is not possible or practical due to signal degradation; coherent demodulation; multipath equalization to equalize frequency dependent multipath; and demodulation filtering.

  5. Method of differential-phase/absolute-amplitude QAM

    DOEpatents

    Dimsdle, Jeffrey William

    2008-10-21

    A method of quadrature amplitude modulation involving encoding phase differentially and amplitude absolutely, allowing for a high data rate and spectral efficiency in data transmission and other communication applications, and allowing for amplitude scaling to facilitate data recovery; amplitude scale tracking to track-out rapid and severe scale variations and facilitate successful demodulation and data retrieval; 2.sup.N power carrier recovery; incoherent demodulation where coherent carrier recovery is not possible or practical due to signal degradation; coherent demodulation; multipath equalization to equalize frequency dependent multipath; and demodulation filtering.

  6. Method of differential-phase/absolute-amplitude QAM

    DOEpatents

    Dimsdle, Jeffrey William

    2007-07-17

    A method of quadrature amplitude modulation involving encoding phase differentially and amplitude absolutely, allowing for a high data rate and spectral efficiency in data transmission and other communication applications, and allowing for amplitude scaling to facilitate data recovery; amplitude scale tracking to track-out rapid and severe scale variations and facilitate successful demodulation and data retrieval; 2.sup.N power carrier recovery; incoherent demodulation where coherent carrier recovery is not possible or practical due to signal degradation; coherent demodulation; multipath equalization to equalize frequency dependent multipath; and demodulation filtering.

  7. Method of differential-phase/absolute-amplitude QAM

    DOEpatents

    Dimsdle, Jeffrey William

    2007-10-02

    A method of quadrature amplitude modulation involving encoding phase differentially and amplitude absolutely, allowing for a high data rate and spectral efficiency in data transmission and other communication applications, and allowing for amplitude scaling to facilitate data recovery; amplitude scale tracking to track-out rapid and severe scale variations and facilitate successful demodulation and data retrieval; 2.sup.N power carrier recovery; incoherent demodulation where coherent carrier recovery is not possible or practical due to signal degradation; coherent demodulation; multipath equalization to equalize frequency dependent multipath; and demodulation filtering.

  8. Method of differential-phase/absolute-amplitude QAM

    DOEpatents

    Dimsdle, Jeffrey William

    2009-09-01

    A method of quadrature amplitude modulation involving encoding phase differentially and amplitude absolutely, allowing for a high data rate and spectral efficiency in data transmission and other communication applications, and allowing for amplitude scaling to facilitate data recovery; amplitude scale tracking to track-out rapid and severe scale variations and facilitate successful demodulation and data retrieval; 2.sup.N power carrier recovery; incoherent demodulation where coherent carrier recovery is not possible or practical due to signal degradation; coherent demodulation; multipath equalization to equalize frequency dependent multipath; and demodulation filtering.

  9. In-flight Absolute Radiometric Calibration of the Thematic Mapper

    NASA Technical Reports Server (NTRS)

    Castle, K. R.; Holm, R. G.; Kastner, C. J.; Palmer, J. M.; Slater, P. N.; Dinguirard, M.; Ezra, C. E.; Jackson, D.; Savage, R. K.

    1984-01-01

    The Thematic Mapper (TM) multispectral scanner system was placed into Earth orbit on July 16, 1982, as part of NASA's LANDSAT 4 payload. To determine temporal changes of the absolute radiometric calibration of the entire system in flight, spectroradiometric measurements of the ground and the atmosphere are made simultaneously with TM image acquisitions over the White Sands, New Mexico area. By entering the measured values into an atmospheric radiative transfer program, the radiance levels at the entrance pupil of the TM in four of the TM spectral bands are determined. These levels are compared to the output digital counts from the detectors that sampled the radiometrically measured ground area, thus providing an absolute radiometric calibration of the entire TM system utilizing those detectors. By reference to an adjacent, larger uniform area, the calibration is extended to all 16 detectors in each of the three bands.

  10. In-flight absolute radiometric calibration of the thematic mapper

    NASA Technical Reports Server (NTRS)

    Castle, K. R.; Holm, R. G.; Kastner, C. J.; Palmer, J. M.; Slater, P. N.; Dinguirard, M.; Ezra, C. E.; Jackson, R. D.; Savage, R. K.

    1984-01-01

    In order to determine temporal changes of the absolute radiometric calibration of the entire TM system in flight spectroradiometric measurements of the ground and the atmosphere were made simultaneously with TM image collections over the White Sands, New Mexico area. By entering the measured values in an atmospheric radiative transfer program, the radiance levels in four of the spectral bands of the TM were determined, band 1:0.45 to 0.52 micrometers, band 2:0.53 to 0.61 micrometers band 3:0.62 to 0.70 micrometers and 4:0.78 to 0.91 micrometers. These levels were compared to the output digital counts from the detectors that sampled the radiometrically measured ground area, thus providing an absolute radiometric calibration of the entire TM system utilizing those detectors.

  11. In-flight absolute radiometric calibration of the Thematic Mapper

    NASA Technical Reports Server (NTRS)

    Castle, K. R.; Holm, R. G.; Kastner, C. J.; Palmer, J. M.; Slater, P. N.; Dinguirard, M.; Ezra, C. E.; Jackson, R. D.; Savage, R. K.

    1984-01-01

    In order to determine temporal changes of the absolute radiometric calibration of the entire TM system in flight spectroradiometric measurements of the ground and the atmosphere were made simultaneously with TM image collections over the White Sands, NM area. By entering the measured values in an atmospheric radiative transfer program, the radiance levels in four of the spectral bands of the TM were determined, band 1: 0.45 to 0.52 micrometers, band 2: 0.53 to 0.61 micrometers, band 3: 0.62 to 0.70 micrometers, and 4: 0.78 to 0.91 micrometers. These levels were compared to the output digital counts from the detectors that sampled the radiometrically measured ground area, thus providing an absolute radiometric calibration of the entire TM system utilizing those detectors. Previously announced in STAR as N84-15633

  12. Enumeration of absolute cell counts using immunophenotypic techniques.

    PubMed

    Mandy, F; Brando, B

    2001-05-01

    Absolute counting of cells or cell subsets has a number of significant clinical applications: monitoring the disease status of HIV-infected patients, enumerating residual white blood cells in leukoreduced blood products, and assessing immunodeficiency in a variety of situations. The single-platform method (flow cytometry alone) has emerged as the method of choice for absolute cell enumeration. This technology counts only the cells of interest in a precisely determined blood volume. Exact cell identification is accomplished by a logical electronic gating algorithm capable of identifying lineage-specific immunofluorescent markers. Exclusion of unwanted cells is automatic. This extensive and detailed unit presents protocols for both volumetric and flow-rate determination of residual white blood cells and of leukocyte subsets. PMID:18770719

  13. Multiple-integrating sphere spectrophotometer for measuring absolute spectral reflectance and transmittance.

    PubMed

    Zerlaut, G A; Anderson, T E

    1981-11-01

    A spectroreflectometer/transmissometer is described that permits determination of absolute optical characteristics in the 300-2600-nm wavelength region (which is essentially the complete solar spectrum). The uniqueness of the instrument derives from use of three rapidly interchangeable 20-cm (8-in.) integrating spheres to measure (1) absolute hemispherical spectral reflectance as a function of angles of incidence from -40 to +40 degrees employing an Edwards-type integrating sphere with a center-mounted sample [using small 2.5-cm (1-in.) diam specimens], (2) absolute hemispherical and absolute diffuse spectral reflectance at an angle of incidence of 20 degrees employing a sphere with a wall-mounted sample (for large specimens) and a screened detector, and (3) absolute hemispherical and absolute directional (near-normal exitance) transmittance employing a complete integrating sphere with the only ports being for the sample and reference beams. Data are presented that demonstrate the ability to measure the spectral reflectance of nonmirror surfaces to an absolute accuracy of 0.995 (an uncertainty of +/-0.005 reflectance units) in both reflectance spheres and of highly specular mirrors to an absolute accuracy of 0.993 (an uncertainty of +/-0.007 reflectance units). Spectral transmittance can be measured to an absolute accuracy of better than 0.995 (an uncertainty of +/-0.005 transmittance units). PMID:20372262

  14. Electroweak absolute, meta-, and thermal stability in neutrino mass models

    NASA Astrophysics Data System (ADS)

    Lindner, Manfred; Patel, Hiren H.; Radovčić, Branimir

    2016-04-01

    We analyze the stability of the electroweak vacuum in neutrino mass models containing right-handed neutrinos or fermionic isotriplets. In addition to considering absolute stability, we place limits on the Yukawa couplings of new fermions based on metastability and thermal stability in the early Universe. Our results reveal that the upper limits on the neutrino Yukawa couplings can change significantly when the top quark mass is allowed to vary within the experimental range of uncertainty in its determination.

  15. Diagnostic Application of Absolute Neutron Activation Analysis in Hematology

    SciTech Connect

    Zamboni, C.B.; Oliveira, L.C.; Dalaqua, L. Jr.

    2004-10-03

    The Absolute Neutron Activation Analysis (ANAA) technique was used to determine element concentrations of Cl and Na in blood of healthy group (male and female blood donators), select from Blood Banks at Sao Paulo city, to provide information which can help in diagnosis of patients. This study permitted to perform a discussion about the advantages and limitations of using this nuclear methodology in hematological examinations.

  16. Absolute partial decay branching-ratios in 16O

    NASA Astrophysics Data System (ADS)

    Wheldon, C.; Ashwood, N. I.; Barr, M.; Curtis, N.; Freer, M.; Kokalova, Tz; Malcolm, J. D.; Spencer, S. J.; Ziman, V. A.; Faestermann, Th; Krücken, R.; Wirth, H.-F.; Hertenberger, R.; Lutter, R.; Bergmaier, A.

    2013-04-01

    The a-transfer reaction 126C(63Li, d)168O* has been performed at a 6Li bombarding energy of 42 MeV to populate excited states in 13C and 16O. Absolute branching ratios have been unambiguously determined for states in the excitation energy range 13.85 to 15.87 MeV and reduced widths are extracted.

  17. Absolute configuration of a chiral CHD group via neutron diffraction: confirmation of the absolute stereochemistry of the enzymatic formation of malic acid

    SciTech Connect

    Bau, R.; Brewer, I.; Chiang, M.Y.; Fujita, S.; Hoffman, J.; Watkins, M.I.; Koetzle, T.F.

    1983-09-30

    Neutron diffraction has been used to monitor the absolute stereochemistry of an enzymatic reaction. (-)(2S)malic-3-d acid was prepared by the action of fumarase on fumaric acid in D/sub 2/O. After a large number of cations were screened, it was found that (+)(R)..cap alpha..-phenylethylamine forms the large crystals necessary for a neutron diffraction analysis. The subsequent structure determination showed that (+)(R)..cap alpha..-phenylethylammonium (-)(2S)malate-3-d has an absolute configuration of R at the CHD site. This result confirms the absolute stereochemistry of fumarate-to-malate transformation as catalyzed by the enzyme fumarase.

  18. Absolute calibration technique for broadband ultrasonic transducers

    NASA Technical Reports Server (NTRS)

    Yost, William T. (Inventor); Cantrell, John H. (Inventor)

    1994-01-01

    Calibrating an ultrasonic transducer can be performed with a reduced number of calculations and testing. A wide-band pulser is connected to an ultrasonic transducer under test to generate ultrasonic waves in a liquid. A single frequency is transmitted to the electrostatic acoustic transducer (ESAT) and the voltage change produced is monitored. Then a broadband ultrasonic pulse is generated by the ultrasonic transducer and received by the ESAT. The output of the ESAT is amplified and input to a digitized oscilloscope for fast Fourier transform. The resulting plot is normalized with the monitored signal from the single frequency pulse. The plot is then corrected for characteristics of the membrane and diffraction effects. The transfer function of the final plot is determined. The transfer function gives the final sensitivity of the ultrasonic transducer as a function of frequency. The advantage of the system is the speed of calibrating the transducer by a reduced number of measurements and removal of the membrane and diffraction effects.

  19. Absolute magnitudes and phase coefficients of trans-Neptunian objects

    NASA Astrophysics Data System (ADS)

    Alvarez-Candal, A.; Pinilla-Alonso, N.; Ortiz, J. L.; Duffard, R.; Morales, N.; Santos-Sanz, P.; Thirouin, A.; Silva, J. S.

    2016-02-01

    Context. Accurate measurements of diameters of trans-Neptunian objects (TNOs) are extremely difficult to obtain. Thermal modeling can provide good results, but accurate absolute magnitudes are needed to constrain the thermal models and derive diameters and geometric albedos. The absolute magnitude, HV, is defined as the magnitude of the object reduced to unit helio- and geocentric distances and a zero solar phase angle and is determined using phase curves. Phase coefficients can also be obtained from phase curves. These are related to surface properties, but only few are known. Aims: Our objective is to measure accurate V-band absolute magnitudes and phase coefficients for a sample of TNOs, many of which have been observed and modeled within the program "TNOs are cool", which is one of the Herschel Space Observatory key projects. Methods: We observed 56 objects using the V and R filters. These data, along with those available in the literature, were used to obtain phase curves and measure V-band absolute magnitudes and phase coefficients by assuming a linear trend of the phase curves and considering a magnitude variability that is due to the rotational light-curve. Results: We obtained 237 new magnitudes for the 56 objects, six of which were without previously reported measurements. Including the data from the literature, we report a total of 110 absolute magnitudes with their respective phase coefficients. The average value of HV is 6.39, bracketed by a minimum of 14.60 and a maximum of -1.12. For the phase coefficients we report a median value of 0.10 mag per degree and a very large dispersion, ranging from -0.88 up to 1.35 mag per degree.

  20. Determination of the time delay in the case of two-path propagation on the basis of the attenuation characteristics for two adjacent frequencies

    NASA Technical Reports Server (NTRS)

    Gilroi, H. G.

    1979-01-01

    Pronounced fading occurring in the line of sight radio links at frequencies below 10 GHz can be traced to the effects of multipath propagation. Modulation disturbances depend on travel time differences between the direct wave and the wave which is reflected at atmospheric layers. A method described for the determination of the time delay is based on an indirect approach which utilizes the difference in fading at various frequencies. The method was employed in measurements involving a distance of 181 km. The results obtained in the measurement are discussed.