Science.gov

Sample records for absorb large amounts

  1. The discovery of large amounts of cold, X-ray absorbing matter in cooling flows

    NASA Technical Reports Server (NTRS)

    White, D. A.; Fabian, A. C.; Johnstone, R. M.; Mushotzky, R. F.; Arnaud, K. A.

    1991-01-01

    The discovery of significant excess absorption in the X-ray spectra of 12 clusters of galaxies is reported. The spectra also require a cooling-flow component, which confirms the results of imaging studies of the clusters showing the strongly peaked emission characteristic of cooling flows. The total mass of absorbing gas is determined on the assumption that it is distributed through the cooling flow region and has cosmic abundance. It is shown that the gas is most likely in the form of small cold clouds. The excess absorption is interpreted as being due to photoelectric absorption in cold gas clouds distributed through the cooling flows.

  2. The detection of large amounts of cool, x ray absorbing gas in distant clusters of galaxies. What does this mean?

    NASA Technical Reports Server (NTRS)

    Wang, Qingde; Stocke, John T.

    1993-01-01

    We present an x-ray spectral study of 12 distant (z = 0.17-0.54) rich clusters of galaxies observed with the Einstein Observatory Imaging Proportional Counter. These x-ray spectral data show evidence for substantial excess absorptions beyond those expected in the galaxy, indicating the presence of large amounts of x-ray absorbing cool gas in these distant clusters. The mean value of the excess absorptions corresponds to an absorbing gas column density approximately greater than 10(exp 21)/sq cm. We calculate the x-ray luminosities of the clusters with observed fluxes only in the 0.8-3.5 keV band where the fluxes are less effected by the absorptions, and use the temperature-to-luminosity correlation (known only for nearby clusters) to estimate the temperatures of the hot intracluster medium (ICM) in the distant clusters. These temperature estimates, together with the spectral fits, provide further constraints on the column densities in the individual clusters. For the cluster CL 0016+16, the lower limit on the column density is found to be 8 x 10(exp 20)/sq cm at the 99 percent confidence limit. We also show that the ratio of the temperature obtained from the spectral fit to the temperature expected from the correlation tends to decrease with increasing look-back time, indicating possible temperature evolution of the hot ICM in the recent past. The inclusion of this evolutionary effect further increases the absorptions required in fitting the spectra.

  3. Transmission of large amounts of scientific data using laser technology

    NASA Astrophysics Data System (ADS)

    Isaev, E. A.; Tarasov, P. A.

    2016-08-01

    Currently, the volume of figures generated by different research scientific projects (the Large Hadron Collider (Large Hadron Collider, LHC), The Square Kilometre Array (SKA)), can reach tens of petabytes per day. The only technical solution that allows you to transfer such large amounts of scientific data to the places of their processing is the transfer of information by means of laser technology, using different propagation environment. This article discusses the possibility of data transmission via fiber-optic networks, data transmission using the modulation binary stream of light source by a special LED light source, the neccessity to apply laser technologies for deep space communications, the principle for an unlimited expansion of the capacity of laser data link. Also in this study is shown the need for a substantial increase in data transfer speed via a pre-existing communication networks and via the construction of new channels of communication that will cope with the transfer of very large scale data volumes, taking into account the projected rate of growth.

  4. Very Large Amounts of Radiation are Required to Produce Cancer

    PubMed Central

    Brooks, Antone L.; Hui, T. Edmond; Couch, Lezlie A.

    2007-01-01

    The public fear of radiation is in part driven by the Linear No Threshold Hypothesis (LNTH), or the concept that each and every ionization increases the risk for cancer. Even if this were true, it is important to recognize that the increased risk is very small at low doses and cannot be detected. This paper demonstrates the large number of assumptions and extrapolations needed when using the LNTH to estimate low-dose cancer risk. The manuscript provides information at every level of biological organization suggesting that many of these linear assumptions do not hold. While the initial damage may be produced linearly with dose, the processing of that damage is very non-linear. Finally, the paper provides the unique prospective on radiation-induced cancer, demonstrating that it takes large amounts (total energy) of radiation delivered to large populations to detect an increase in cancer frequency. These observations are supported by both theoretical calculations and examples based on past human radiation exposure. PMID:18648559

  5. Discovering Related Clinical Concepts Using Large Amounts of Clinical Notes

    PubMed Central

    Ganesan, Kavita; Lloyd, Shane; Sarkar, Vikren

    2016-01-01

    The ability to find highly related clinical concepts is essential for many applications such as for hypothesis generation, query expansion for medical literature search, search results filtering, ICD-10 code filtering and many other applications. While manually constructed medical terminologies such as SNOMED CT can surface certain related concepts, these terminologies are inadequate as they depend on expertise of several subject matter experts making the terminology curation process open to geographic and language bias. In addition, these terminologies also provide no quantifiable evidence on how related the concepts are. In this work, we explore an unsupervised graphical approach to mine related concepts by leveraging the volume within large amounts of clinical notes. Our evaluation shows that we are able to use a data driven approach to discovering highly related concepts for various search terms including medications, symptoms and diseases. PMID:27656096

  6. Making large amounts of meteorological plots easily accessible to users

    NASA Astrophysics Data System (ADS)

    Lamy-Thepaut, Sylvie; Siemen, Stephan; Sahin, Cihan; Raoult, Baudouin

    2015-04-01

    The European Centre for Medium-Range Weather Forecasts (ECMWF) is an international organisation providing its member organisations with forecasts in the medium time range of 3 to 15 days, and some longer-range forecasts for up to a year ahead, with varying degrees of detail. As part of its mission, ECMWF generates an increasing number of forecast data products for its users. To support the work of forecasters and researchers and to let them make best use of ECMWF forecasts, the Centre also provides tools and interfaces to visualise their products. This allows users to make use of and explore forecasts without having to transfer large amounts of raw data. This is especially true for products based on ECMWF's 50 member ensemble forecast, where some specific processing and visualisation are applied to extract information. Every day, thousands of raw data are being pushed to the ECMWF's interactive web charts application called ecCharts, and thousands of products are processed and pushed to ECMWF's institutional web site ecCharts provides a highly interactive application to display and manipulate recent numerical forecasts to forecasters in national weather services and ECMWF's commercial customers. With ecCharts forecasters are able to explore ECMWF's medium-range forecasts in far greater detail than has previously been possible on the web, and this as soon as the forecast becomes available. All ecCharts's products are also available through a machine-to-machine web map service based on the OGC Web Map Service (WMS) standard. ECMWF institutional web site provides access to a large number of graphical products. It was entirely redesigned last year. It now shares the same infrastructure as ECMWF's ecCharts, and can benefit of some ecCharts functionalities, for example the dashboard. The dashboard initially developed for ecCharts allows users to organise their own collection of products depending on their work flow, and is being further developed. In its first

  7. Knowledge discovery: Extracting usable information from large amounts of data

    SciTech Connect

    Whiteson, R.

    1998-12-31

    The threat of nuclear weapons proliferation is a problem of world wide concern. Safeguards are the key to nuclear nonproliferation and data is the key to safeguards. The safeguards community has access to a huge and steadily growing volume of data. The advantages of this data rich environment are obvious, there is a great deal of information which can be utilized. The challenge is to effectively apply proven and developing technologies to find and extract usable information from that data. That information must then be assessed and evaluated to produce the knowledge needed for crucial decision making. Efficient and effective analysis of safeguards data will depend on utilizing technologies to interpret the large, heterogeneous data sets that are available from diverse sources. With an order-of-magnitude increase in the amount of data from a wide variety of technical, textual, and historical sources there is a vital need to apply advanced computer technologies to support all-source analysis. There are techniques of data warehousing, data mining, and data analysis that can provide analysts with tools that will expedite their extracting useable information from the huge amounts of data to which they have access. Computerized tools can aid analysts by integrating heterogeneous data, evaluating diverse data streams, automating retrieval of database information, prioritizing inputs, reconciling conflicting data, doing preliminary interpretations, discovering patterns or trends in data, and automating some of the simpler prescreening tasks that are time consuming and tedious. Thus knowledge discovery technologies can provide a foundation of support for the analyst. Rather than spending time sifting through often irrelevant information, analysts could use their specialized skills in a focused, productive fashion. This would allow them to make their analytical judgments with more confidence and spend more of their time doing what they do best.

  8. Large amounts of antiproton production by heavy ion collision

    SciTech Connect

    Takahashi, Hiroshi; Powell, J.

    1987-01-01

    To produce large amounts of antiprotons, on the order of several grams/year, use of machines to produce nuclear collisions are studied. These can be of either proton-proton, proton-nucleus and nucleus-nucleus in nature. To achieve high luminosity colliding beams, on the order of 10/sup 41/ m/cm/sup 2/, a self-colliding machine is required, rather than a conventional circular colliding type. The self-colliding machine can produce additional antiprotons through successive collisions of secondary particles, such as spectator nucleons. A key problem is how to collect the produced antiprotons without capture by beam nuclei in the collision zone. Production costs for anti-matter are projected for various energy source options and technology levels. Dedicated facilities using heavy ion collisions could produce antiproton at substantially less than 1 million $/milligram. With co-production of other valuable products, e.g., nuclear fuel for power reactors, antiproton costs could be reduced to even lower values.

  9. Large-scale electrochromic devices for smart windows and absorbers

    NASA Astrophysics Data System (ADS)

    Meisel, Thomas; Braun, Ruediger

    1992-11-01

    Application of smart windows and absorbers demand electrochromic (EC) devices with long term stability and a large scale production technology. The paper presents recent results on preparation of rigid and flexible EC devices with 0.3 X 0.3 m2 active area in a three layer arrangement (polyaniline/polymeric electrolyte/tungsten trioxide). The main items and risks of processing an EC element are discussed. It is shown, that highly conductive, chemical resistant electrodes (sheet resistance 5 (Omega) /sq., transparency 85%) on flexible PMMA and PC substrates can be prepared by low temperature sputtering of indium tin oxide (ITO). Deposition apparatus and parameters are described. Well known standard techniques for the synthesis of EC films like polyaniline and tungsten trioxide are adapted for large surfaces: polyaniline and tungsten trioxide based EC films on ITO glass have been prepared with chemical and electrochemical preparation techniques. Electrode geometry plays an important role for the homogeneity of the grown film. We succeed in minimizing tolerances in optical density over 0.3 X 0.3 m2 down to 2%. The solid polymer electrolyte essentially determines the performance of the EC device. High transmittance, proper conductivity, and strong adhesion, are the main attributes.

  10. Making large amounts of meteorological data accessible through visualisation

    NASA Astrophysics Data System (ADS)

    Siemen, Stephan; Lamy-Thepaut, Sylvie

    2013-04-01

    The European Centre for Medium-Range Weather Forecasts (ECMWF) is an international organisation providing its member organisations with forecasts in the medium time range of 3 to 15 days. As part of its mission, ECMWF generates an increasing number of forecast data products for its users. To support the work of forecasters and researchers and to let them make best use of ECMWF forecasts, the Centre also provides tools and interfaces to visualise their products. This allows users to make use of and explore forecasts without having to transfer large amounts of raw data. This is especially true for products based on ECMWF's 50 member strong ensemble forecast. Users can choose to explore ECMWF's forecasts from the web or through visualisation tools installed locally or at ECMWF. ECMWF's new in-house developed web service, ecCharts, displays recent numerical forecasts to forecasters in national weather services. The functions that ecCharts provides are beyond standard web charts, in that forecasters can use the service to create bespoke charts on demand and do this themselves as and when they need to using an intuitive web interface. With ecCharts they are able to explore ECMWF's medium-range forecasts in far greater detail than has previously been possible on the web. Beside the interactive user interface built using jQuery the service also offers a machine-to-machine web map service based on the OGC Web Map Service (WMS) standard. The WMS service is primary intended to be used by forecaster workstations to integrate maps generated at ECMWF. The main challenge was to achieve fast response times even though the data volume and processing effort is quite high. PNG is the main format served but SVG is being investigated as a vector alternative. This talk will present examples of complex meteorological maps and graphs which show new possibilities users have gained by using the web as a medium. More advanced possibilities are available directly to users of the

  11. Expert system shell to reason on large amounts of data

    NASA Technical Reports Server (NTRS)

    Giuffrida, Gionanni

    1994-01-01

    The current data base management systems (DBMS's) do not provide a sophisticated environment to develop rule based expert systems applications. Some of the new DBMS's come with some sort of rule mechanism; these are active and deductive database systems. However, both of these are not featured enough to support full implementation based on rules. On the other hand, current expert system shells do not provide any link with external databases. That is, all the data are kept in the system working memory. Such working memory is maintained in main memory. For some applications the reduced size of the available working memory could represent a constraint for the development. Typically these are applications which require reasoning on huge amounts of data. All these data do not fit into the computer main memory. Moreover, in some cases these data can be already available in some database systems and continuously updated while the expert system is running. This paper proposes an architecture which employs knowledge discovering techniques to reduce the amount of data to be stored in the main memory; in this architecture a standard DBMS is coupled with a rule-based language. The data are stored into the DBMS. An interface between the two systems is responsible for inducing knowledge from the set of relations. Such induced knowledge is then transferred to the rule-based language working memory.

  12. Determination of small and large amounts of fluorine in rocks

    USGS Publications Warehouse

    Grimaldi, F.S.; Ingram, B.; Cuttitta, F.

    1955-01-01

    Gelatinous silica and aluminum ions retard the distillation of fluorine in the Willard and Winter distillation method. A generally applicable, simple method for the determination of fluorine in rocks containing aluminum or silicon or both as major constituents was desired. In the procedure developed, the sample is fused with a mixture of sodium carbonate and zinc oxide, leached with water, and filtered. The residue is granular and retains nearly all of the silica. The fluorine in the filtrate is distilled directly from a perchloric acid-phosphoric acid mixture. Phosphoric acid permits the quantitative distillation of fluorine in the presence of much aluminum at the usual distillation temperature and without the collection of large volumes of distillate. The fluorine is determined either by microtitration with thorium nitrate or colorimetrically with thoron. The procedure is rapid and has yielded excellent results on silicate rocks and on samples from the aluminum phosphate (leached) zone of the Florida phosphate deposits.

  13. Comparison Analysis among Large Amount of SNS Sites

    NASA Astrophysics Data System (ADS)

    Toriumi, Fujio; Yamamoto, Hitoshi; Suwa, Hirohiko; Okada, Isamu; Izumi, Kiyoshi; Hashimoto, Yasuhiro

    In recent years, application of Social Networking Services (SNS) and Blogs are growing as new communication tools on the Internet. Several large-scale SNS sites are prospering; meanwhile, many sites with relatively small scale are offering services. Such small-scale SNSs realize small-group isolated type of communication while neither mixi nor MySpace can do that. However, the studies on SNS are almost about particular large-scale SNSs and cannot analyze whether their results apply for general features or for special characteristics on the SNSs. From the point of view of comparison analysis on SNS, comparison with just several types of those cannot reach a statistically significant level. We analyze many SNS sites with the aim of classifying them by using some approaches. Our paper classifies 50,000 sites for small-scale SNSs and gives their features from the points of network structure, patterns of communication, and growth rate of SNS. The result of analysis for network structure shows that many SNS sites have small-world attribute with short path lengths and high coefficients of their cluster. Distribution of degrees of the SNS sites is close to power law. This result indicates the small-scale SNS sites raise the percentage of users with many friends than mixi. According to the analysis of their coefficients of assortativity, those SNS sites have negative values of assortativity, and that means users with high degree tend to connect users with small degree. Next, we analyze the patterns of user communication. A friend network of SNS is explicit while users' communication behaviors are defined as an implicit network. What kind of relationships do these networks have? To address this question, we obtain some characteristics of users' communication structure and activation patterns of users on the SNS sites. By using new indexes, friend aggregation rate and friend coverage rate, we show that SNS sites with high value of friend coverage rate activate diary postings

  14. Elephant’s breast milk contains large amounts of glucosamine

    PubMed Central

    TAKATSU, Zenta; TSUDA, Muneya; YAMADA, Akio; MATSUMOTO, Hiroshi; TAKAI, Akira; TAKEDA, Yasuhiro; TAKASE, Mitsunori

    2016-01-01

    Hand-reared elephant calves that are nursed with milk substitutes sometimes suffer bone fractures, probably due to problems associated with nutrition, exercise, sunshine levels and/or genetic factors. As we were expecting the birth of an Asian elephant (Elephas maximus), we analyzed elephant’s breast milk to improve the milk substitutes for elephant calves. Although there were few nutritional differences between conventional substitutes and elephant’s breast milk, we found a large unknown peak in the breast milk during high-performance liquid chromatography-based amino acid analysis and determined that it was glucosamine (GlcN) using liquid chromatography/mass spectrometry. We detected the following GlcN concentrations [mean ± SD] (mg/100 g) in milk hydrolysates produced by treating samples with 6M HCl for 24 hr at 110°C: four elephant’s breast milk samples: 516 ± 42, three cow’s milk mixtures: 4.0 ± 2.2, three mare’s milk samples: 12 ± 1.2 and two human milk samples: 38. The GlcN content of the elephant’s milk was 128, 43 and 14 times greater than those of the cow’s, mare’s and human milk, respectively. Then, we examined the degradation of GlcN during 0–24 hr hydrolyzation with HCl. We estimated that elephant’s milk contains >880 mg/100 g GlcN, which is similar to the levels of major amino acids in elephant’s milk. We concluded that a novel GlcN-containing milk substitute should be developed for elephant calves. The efficacy of GlcN supplements is disputed, and free GlcN is rare in bodily fluids; thus, the optimal molecular form of GlcN requires a further study. PMID:28049867

  15. A Fluidically Tunable Metasurface Absorber for Flexible Large-Scale Wireless Ethanol Sensor Applications

    PubMed Central

    Kim, Hyung Ki; Lee, Dongju; Lim, Sungjoon

    2016-01-01

    In this paper, a novel flexible tunable metasurface absorber is proposed for large-scale remote ethanol sensor applications. The proposed metasurface absorber consists of periodic split-ring-cross resonators (SRCRs) and microfluidic channels. The SRCR patterns are inkjet-printed on paper using silver nanoparticle inks. The microfluidic channels are laser-etched on polydimethylsiloxane (PDMS) material. The proposed absorber can detect changes in the effective permittivity for different liquids. Therefore, the absorber can be used for a remote chemical sensor by detecting changes in the resonant frequencies. The performance of the proposed absorber is demonstrated with full-wave simulation and measurement results. The experimental results show the resonant frequency increases from 8.9 GHz to 10.04 GHz when the concentration of ethanol is changed from 0% to 100%. In addition, the proposed absorber shows linear frequency shift from 20% to 80% of the different concentrations of ethanol. PMID:27509498

  16. [Simultaneous determination of migration amounts of antioxidants and ultraviolet absorbents by high performance liquid chromatography in food contact materials].

    PubMed

    Li, Chengfa; Li, Ying; Chen, Zhinan; Liang, Feng; Chen, Xuhui; Wu, Shaojing; Li, Yongtao; Sun, Xiaoying

    2014-06-01

    An efficient analytical method for the quantitative determination of migration levels of antioxidants and ultraviolet absorbents in food contact materials by high performance liquid chromatography (HPLC) has been developed. The analytical method showed good linearity with the correlation coefficients (r2) > or = 0.999 8 for all the compounds. The limits of detection were between 0.01 mg/L and 0.22 mg/L and the limits of quantification were in the range of 0.03 to 0.85 mg/L for the 23 analytes. According to the European Union Directive No 10/2011, five food simulants were investigated: 30 g/L acetic acid, 10% (v/v) ethanol, 20% (v/v) ethanol, 50% (v/v) ethanol, and fatty food simulant (isooctane). The recoveries were in the range of 92.8%-117.7%, with the relative standard deviations of 0.95%-9.72%. The effects of different experimental conditions on the recoveries of antioxidants and UV absorbents were studied. The results showed that the method is accurate and stable, and can meet the requirements of European Commission Regulation (EU) No 10/2011 and GB 9685-2008 for the specific migration limits (SML) of the antioxidants and ultraviolet absorbents in real food contact plastic materials and article samples. The method has been applied to determine the migration levels of antioxidants and ultraviolet absorbents in different simulants from the migration tests of 30 batches of food contact material samples.

  17. Automated Hybridization of X-ray Absorber Elements-A Path to Large Format Microcalorimeter Arrays

    NASA Technical Reports Server (NTRS)

    Moseley, S.; Kelley, R.; Allen, C.; Kilbourne, C.; Costen, N.; Miller, T.

    2007-01-01

    In the design of microcalorimeters, it is often desirable to produce the X-ray absorber separately from the detector element. In this case, the attachment of the absorber to the detector element with the required thermal and mechanical characteristics is a major challenge. In such arrays, the attachment has been done by hand. This process is not easily extended to the large format arrays required for future X- ray astronomy missions such as the New x-ray Telescope or NeXT. In this paper we present an automated process for attaching absorber tiles to the surface of a large-scale X-ray detector array. The absorbers are attached with stycast epoxy to a thermally isolating polymer structure made of SU-8. SU-8 is a negative epoxy based photo resist produced by Microchem. We describe the fabrication of the X-ray absorbers and their suspension on a handle die in an adhesive matrix. We describe the production process for the polymer isolators on the detector elements. We have developed a new process for the alignment, and simultaneous bonding of the absorber tiles to an entire detector array. This process uses equipment and techniques used in the flip-chip bonding industry and approaches developed in the fabrication of the XRS-2 instrument. XRS-2 was an X-ray spectrometer that was launched on the Suzaku telescope in July 10, 2005. We describe the process and show examples of sample arrays produced by this process. Arrays with up to 300 elements have been bonded. The present tests have used dummy absorbers made of Si. In future work, we will demonstrate bonding of HgTe absorbers.

  18. A simple biosynthetic pathway for large product generation from small substrate amounts

    NASA Astrophysics Data System (ADS)

    Djordjevic, Marko; Djordjevic, Magdalena

    2012-10-01

    A recently emerging discipline of synthetic biology has the aim of constructing new biosynthetic pathways with useful biological functions. A major application of these pathways is generating a large amount of the desired product. However, toxicity due to the possible presence of toxic precursors is one of the main problems for such production. We consider here the problem of generating a large amount of product from a potentially toxic substrate. To address this, we propose a simple biosynthetic pathway, which can be induced in order to produce a large number of the product molecules, by keeping the substrate amount at low levels. Surprisingly, we show that the large product generation crucially depends on fast non-specific degradation of the substrate molecules. We derive an optimal induction strategy, which allows as much as three orders of magnitude increase in the product amount through biologically realistic parameter values. We point to a recently discovered bacterial immune system (CRISPR/Cas in E. coli) as a putative example of the pathway analysed here. We also argue that the scheme proposed here can be used not only as a stand-alone pathway, but also as a strategy to produce a large amount of the desired molecules with small perturbations of endogenous biosynthetic pathways.

  19. Large area and broadband ultra-black absorber using microstructured aluminum doped silicon films

    NASA Astrophysics Data System (ADS)

    Liu, Zhen; Liu, Hai; Wang, Xiaoyi; Yang, Haigui; Gao, Jinsong

    2017-02-01

    A large area and broadband ultra-black absorber based on microstructured aluminum (Al) doped silicon (Si) films prepared by a low-cost but very effective approach is presented. The average absorption of the absorber is greater than 99% within the wide range from 350 nm to 2000 nm, and its size reaches to 6 inches. We investigate the fabrication mechanism of the absorber and find that the Al atom doped in silicon improves the formation of the nanocone-like microstructures on the film surface, resulting in a significant decrease in the reflection of incident light. The absorption mechanism is further discussed by experiments and simulated calculations in detail. The results show that the doped Al atoms and Mie resonance formed in the microstructures contribute the broadband super-high absorption.

  20. Large area and broadband ultra-black absorber using microstructured aluminum doped silicon films

    PubMed Central

    Liu, Zhen; Liu, Hai; Wang, Xiaoyi; Yang, Haigui; Gao, Jinsong

    2017-01-01

    A large area and broadband ultra-black absorber based on microstructured aluminum (Al) doped silicon (Si) films prepared by a low-cost but very effective approach is presented. The average absorption of the absorber is greater than 99% within the wide range from 350 nm to 2000 nm, and its size reaches to 6 inches. We investigate the fabrication mechanism of the absorber and find that the Al atom doped in silicon improves the formation of the nanocone-like microstructures on the film surface, resulting in a significant decrease in the reflection of incident light. The absorption mechanism is further discussed by experiments and simulated calculations in detail. The results show that the doped Al atoms and Mie resonance formed in the microstructures contribute the broadband super-high absorption. PMID:28202899

  1. Change in the amount of epsilon-hexosyllysine, UV absorbance, and fluorescence of collagen with age in different animal species

    SciTech Connect

    Miksik, I.; Deyl, Z. )

    1991-05-01

    Skin and aorta collagen specimens of Wistar rats, white mice, beagle dogs, cats, horses, and human necropsies of different ages were examined with respect to the content of glycated products. The data presented show that (a) glycation and accumulation of the chromophore(s) are comparable in collagen samples from different species of comparable age; (b) glycation and pigmented accumulation increase markedly during the first 5-10 years of age; (c) the extent of glycation is different in different tissues (in particular, glycation of aortal collagen is about twice that of skin collagen); and (d) collagen pigmentation as followed by fluorescence is comparable in aortal and skin collagen (except below 10 years); pigmentation measured by absorbance at 350 nm is, on the contrary, lower in aortal than in skin collagen. Based on the assumption of constant blood glucose level during the life span, it appears feasible to conclude that the degree of nonenzymatic collagen glycation reflects the time period for which the protein was exposed to the action of sugars. This period, because of increased cross-linking, is likely to be extended in older animals. Other factors, such as differences in collagen turnover between different tissues and the intensity of the removal process of the glycated products, should be taken into consideration as well.

  2. Study on Properties of Environment-friendly Concrete Containing Large Amount of Industrial by-products

    NASA Astrophysics Data System (ADS)

    Fujiwara, H.; Maruoka, M.; Sadayama, C.; Nemoto, M.; Yoshikawa, K.; Yamaji, M.

    2015-11-01

    This study aims to reduce CO2 discharged from the cement and concrete industries by effective use of industrial by-products, such as fly ash, blast furnace slag, and so on. In this paper, the properties of concrete containing large amount of industrial by-products and very small amount of alkaline activator including cement or sludge from ready mixed concrete plant are analyzed. As the result, it was confirmed that concretes containing large amount of industrial by-products can achieve sufficient compressive strength. However, these concretes showed poor frost resistance. It was thought that the reason was coarsening of air void system and this caused their poor frost resistance. Therefore, in order to micronize the air void system and improve frost resistance, the combination of air entraining agent and antifoaming agent was applied. By this method, it was confirmed that the frost resistance of some these concrete improved. In this study, other properties of these concretes, such as fresh properties and other durability were evaluated and it was confirmed that these concretes show sufficient properties.

  3. Analytics to Better Interpret and Use Large Amounts of Heterogeneous Data

    NASA Astrophysics Data System (ADS)

    Mathews, T. J.; Baskin, W. E.; Rinsland, P. L.

    2014-12-01

    Data scientists at NASA's Atmospheric Science Data Center (ASDC) are seasoned software application developers who have worked with the creation, archival, and distribution of large datasets (multiple terabytes and larger). In order for ASDC data scientists to effectively implement the most efficient processes for cataloging and organizing data access applications, they must be intimately familiar with data contained in the datasets with which they are working. Key technologies that are critical components to the background of ASDC data scientists include: large RBMSs (relational database management systems) and NoSQL databases; web services; service-oriented architectures; structured and unstructured data access; as well as processing algorithms. However, as prices of data storage and processing decrease, sources of data increase, and technologies advance - granting more people to access to data at real or near-real time - data scientists are being pressured to accelerate their ability to identify and analyze vast amounts of data. With existing tools this is becoming exceedingly more challenging to accomplish. For example, NASA Earth Science Data and Information System (ESDIS) alone grew from having just over 4PBs of data in 2009 to nearly 6PBs of data in 2011. This amount then increased to roughly10PBs of data in 2013. With data from at least ten new missions to be added to the ESDIS holdings by 2017, the current volume will continue to grow exponentially and drive the need to be able to analyze more data even faster. Though there are many highly efficient, off-the-shelf analytics tools available, these tools mainly cater towards business data, which is predominantly unstructured. Inadvertently, there are very few known analytics tools that interface well to archived Earth science data, which is predominantly heterogeneous and structured. This presentation will identify use cases for data analytics from an Earth science perspective in order to begin to identify

  4. High-speed readout method of ID information on a large amount of electronic tags

    NASA Astrophysics Data System (ADS)

    Nagate, Wataru; Sasabe, Masahiro; Nakano, Hirotaka

    2006-10-01

    An electronic tag such as RFID is expected to create new services that cannot be achieved by the traditional bar code. Specifically, in a distribution system, simultaneous readout method of a large amount of electronic tags embedded in products is required to reduce costs and time. In this paper, we propose novel methods, called Response Probability Control (RPC), to accomplish this requirement. In RPC, a reader firstly sends an ID request to electronic tags in its access area. It succeeds reading information on a tag only if other tags do not respond. To improve the readout efficiency, the reader appropriately controls the response probability in accordance with the number of tags. However, this approach cannot entirely avoid a collision of multiple responses. When a collision occurs, ID information is lost. To reduce the amount of lost data, we divide the ID registration process into two steps. The reader first gathers the former part of the original ID, called temporal ID, according to the above method. After obtaining the temporal ID, it sequentially collects the latter part of ID, called remaining ID, based on the temporal ID. Note that we determine the number of bits of a temporal ID in accordance with the number of tags in the access area so that each tag can be distinguishable. Through simulation experiments, we evaluate RPC in terms of the readout efficiency. Simulation results show that RPC can accomplish the readout efficiency 1.17 times higher than the traditional method where there are a thousand of electronic tags whose IDs are 128 bits.

  5. Evaluation of Flush-Mounted, S-Duct Inlets With Large Amounts of Boundary Layer Ingestion

    NASA Technical Reports Server (NTRS)

    Berrier, Bobby L.; Morehouse, Melissa B.

    2003-01-01

    A new high Reynolds number test capability for boundary layer ingesting inlets has been developed for the NASA Langley Research Center 0.3-Meter Transonic Cryogenic Tunnel. Using this new capability, an experimental investigation of four S-duct inlet configurations with large amounts of boundary layer ingestion (nominal boundary layer thickness of about 40% of inlet height) was conducted at realistic operating conditions (high subsonic Mach numbers and full-scale Reynolds numbers). The objectives of this investigation were to 1) develop a new high Reynolds number, boundary-layer ingesting inlet test capability, 2) evaluate the performance of several boundary layer ingesting S-duct inlets, 3) provide a database for CFD tool validation, and 4) provide a baseline inlet for future inlet flow-control studies. Tests were conducted at Mach numbers from 0.25 to 0.83, Reynolds numbers (based on duct exit diameter) from 5.1 million to a fullscale value of 13.9 million, and inlet mass-flow ratios from 0.39 to 1.58 depending on Mach number. Results of this investigation indicate that inlet pressure recovery generally decreased and inlet distortion generally increased with increasing Mach number. Except at low Mach numbers, increasing inlet mass-flow increased pressure recovery and increased distortion. Increasing the amount of boundary layer ingestion (by decreasing inlet throat height and increasing inlet throat width) or ingesting a boundary layer with a distorted profile decreased pressure recovery and increased distortion. Finally, increasing Reynolds number had almost no effect on inlet distortion but increased inlet recovery by about one-half percent at a Mach number near cruise.

  6. Evaluation of Flush-Mounted, S-Duct Inlets with Large Amounts of Boundary Layer Ingestion

    NASA Technical Reports Server (NTRS)

    Berrier, Bobby L.; Morehouse, Melissa B.

    2003-01-01

    A new high Reynolds number test capability for boundary layer ingesting inlets has been developed for the NASA Langley Research Center 0.3-Meter Transonic Cryogenic Tunnel. Using this new capability, an experimental investigation of four S-duct inlet configurations with large amounts of boundary layer ingestion (nominal boundary layer thickness of about 40% of inlet height) was conducted at realistic operating conditions (high subsonic Mach numbers and full-scale Reynolds numbers). The objectives of this investigation were to 1) provide a database for CFD tool validation on boundary layer ingesting inlets operating at realistic conditions and 2) provide a baseline inlet for future inlet flow-control studies. Tests were conducted at Mach numbers from 0.25 to 0.83, Reynolds numbers (based on duct exit diameter) from 5.1 million to a full-scale value of 13.9 million, and inlet mass-flow ratios from 0.39 to 1.58 depending on Mach number. Results of this investigation indicate that inlet pressure recovery generally decreased and inlet distortion generally increased with increasing Mach number. Except at low Mach numbers, increasing inlet mass-flow increased pressure recovery and increased distortion. Increasing the amount of boundary layer ingestion (by decreasing inlet throat height) or ingesting a boundary layer with a distorted (adverse) profile decreased pressure recovery and increased distortion. Finally, increasing Reynolds number had almost no effect on inlet distortion but increased inlet recovery by about one-half percent at a Mach number near cruise.

  7. How to extract clinically useful information from large amount of dialysis related stored data.

    PubMed

    Vito, Domenico; Casagrande, Giustina; Bianchi, Camilla; Costantino, Maria L

    2015-01-01

    The basic storage infrastructure used to gather data from the technological evolution also in the healthcare field was leading to the storing into public or private repository of even higher quantities of data related to patients and their pathological evolution. Big data techniques are spreading also in medical research. By these techniques is possible extract information from complex heterogeneous sources, realizing longitudinal studies focused to correlate the patient status with biometric parameters. In our work we develop a common data infrastructure involving 4 clinical dialysis centers between Lombardy and Switzerland. The common platform has been build to store large amount of clinical data related to 716 dialysis session of 70 patient. The platform is made up by a combination of a MySQL(®) database (Dialysis Database) and a MATLAB-based mining library (Dialysis MATlib). A statistical analysis of these data has been performed on the data gathered. These analyses led to the development of two clinical indexes, representing an example of transformation of big data into clinical information.

  8. Biological soil crusts emit large amounts of NO and HONO affecting the nitrogen cycle in drylands

    NASA Astrophysics Data System (ADS)

    Tamm, Alexandra; Wu, Dianming; Ruckteschler, Nina; Rodríguez-Caballero, Emilio; Steinkamp, Jörg; Meusel, Hannah; Elbert, Wolfgang; Behrendt, Thomas; Sörgel, Matthias; Cheng, Yafang; Crutzen, Paul J.; Su, Hang; Pöschl, Ulrich; Weber, Bettina

    2016-04-01

    Dryland systems currently cover ˜40% of the world's land surface and are still expanding as a consequence of human impact and global change. In contrast to that, information on their role in global biochemical processes is limited, probably induced by the presumption that their sparse vegetation cover plays a negligible role in global balances. However, spaces between the sparse shrubs are not bare, but soils are mostly covered by biological soil crusts (biocrusts). These biocrust communities belong to the oldest life forms, resulting from an assembly between soil particles and cyanobacteria, lichens, bryophytes, and algae plus heterotrophic organisms in varying proportions. Depending on the dominating organism group, cyanobacteria-, lichen-, and bryophyte-dominated biocrusts are distinguished. Besides their ability to restrict soil erosion they fix atmospheric carbon and nitrogen, and by doing this they serve as a nutrient source in strongly depleted dryland ecosystems. In this study we show that a fraction of the nitrogen fixed by biocrusts is metabolized and subsequently returned to the atmosphere in the form of nitric oxide (NO) and nitrous acid (HONO). These gases affect the radical formation and oxidizing capacity within the troposphere, thus being of particular interest to atmospheric chemistry. Laboratory measurements using dynamic chamber systems showed that dark cyanobacteria-dominated crusts emitted the largest amounts of NO and HONO, being ˜20 times higher than trace gas fluxes of nearby bare soil. We showed that these nitrogen emissions have a biogenic origin, as emissions of formerly strongly emitting samples almost completely ceased after sterilization. By combining laboratory, field, and satellite measurement data we made a best estimate of global annual emissions amounting to ˜1.1 Tg of NO-N and ˜0.6 Tg of HONO-N from biocrusts. This sum of 1.7 Tg of reactive nitrogen emissions equals ˜20% of the soil release under natural vegetation according

  9. Nonprotein nitrogen is absorbed from the large intestine and increases nitrogen balance in growing pigs fed a valine-limiting diet.

    PubMed

    Columbus, Daniel A; Lapierre, Hélène; Htoo, John K; de Lange, Cornelis F M

    2014-05-01

    Nitrogen absorption from the large intestine, largely as ammonia and possibly as amino acids (AAs), is generally thought to be of little nutritional value to nonruminant animals and humans. Ammonia-nitrogen absorbed from the large intestine, however, may be recycled into the small intestine as urea and incorporated into microbial AAs, which may then be used by the host. A cecal infusion study was performed to determine the form in which nitrogen is absorbed from the large intestine and the impact of large intestine nitrogen supply on nitrogen balance in growing pigs. Eighteen cecally cannulated barrows (initial body weight: 22.4 ± 1.2 kg) were used to determine the effect of supplying nitrogen into the large intestine from either casein or urea on whole-body nitrogen retention and urea kinetics. Treatments were cecal infusions of saline (control), casein, or urea with nitrogen infused at a rate of 40% of nitrogen intake. In a subsample of 9 pigs, (15)N(15)N-urea was infused via i.v. during the nitrogen-balance period to determine urea kinetics. All pigs were fed a valine-limiting cornstarch-soybean meal-based diet. More than 80% of infused nitrogen was apparently absorbed. Urea flux and urinary nitrogen excretion increased (P ≤ 0.05) by the same amount for both nitrogen sources, but this increase did not fully account for the increase in nitrogen absorption from the large intestine. Whole-body nitrogen retention improved with nitrogen infusions (129 vs. 114 g/d; P < 0.01) and did not differ (P > 0.05) between nitrogen sources. Absorption of nitrogen from the large intestine appears to be in the form of nonprotein nitrogen, which appears to be returned to the small intestine via urea and used there for microbial AA production and should therefore be considered when determining nitrogen and AA supply and requirements.

  10. Nonimaging secondary concentrators for large rim angle parabolic troughs with tubular absorbers

    NASA Astrophysics Data System (ADS)

    Ries, Harald; Spirkl, Wolfgang

    1996-05-01

    For parabolic trough solar collectors with tubular absorbers, we design new tailored secondary concentrators. The design is applicable for any rim angle of a parabolic reflector. With the secondary, the concentration can be increased by a factor of more than 2 with a compact secondary reflector consisting of a single piece, even for the important case of a rim angle of 90 deg. The parabolic reflector can be used without changes; the reduced absorber is still tubular but smaller than the original absorber and slightly displaced toward the primary. concentrators, solar trough collectors, tailored reflectors.

  11. Rotation of large asymmetrical absorbing objects by Laguerre-Gauss beams.

    PubMed

    Herne, Catherine M; Capuzzi, Kristina M; Sobel, Emily; Kropas, Ryan T

    2015-09-01

    In this Letter, we show the manipulation and rotation of opaque graphite through adhesion with optically trapped polystyrene spheres. The absorbing graphite is rotated by the orbital angular momentum transfer from a Laguerre-Gauss laser mode and is trapped due to the presence of refracting spheres. This technique is effective for trapping and rotating absorbing objects of all sizes, including those larger than the laser mode.

  12. Behavioral responses of cotton mice (Peromyscus gossypinus) to large amounts of coarse woody debris.

    SciTech Connect

    Hinkleman, Travis M.

    2004-08-01

    Hinkleman, Travis M. 2004. MS Thesis. Clemson University, Clemson, South Carolina. 62 pp. Coarse woody debris (CWD) is any log, snag, or downed branch >10 cm in diameter. As a major structural feature of forest ecosystems, CWD serves as an important habitat component for a variety of organisms. Rodents frequently use CWD for travel routes and daytime refugia. Although rodents are known to use CWD extensively and selectively, the use and selection of CWD by rodents may vary according to the abundance of CWD. The purpose of this project was to determine the effect of CWD abundance on the habitat use patterns of a common terrestrial rodent, the cotton mouse (Peromyscus gossypinus). I tracked cotton mice with fluorescent pigments and radiotelemetry in 6 plots, situated in loblolly pine (Pinus taeda) stands, with manipulated levels of woody debris. Treatment plots had 6x the amount of woody debris as control plots. I determined log use and movement patterns from the paths produced by powder-tracking, and I identified daytime refugia by radio-tracking. Travel along logs was almost exclusively associated with the surface of logs (91%). The proportion of a movement path associated with logs was not the best predictor of path complexity; rather, the sex of the individual was the only significant indicator of relative displacement (i.e., males moved farther from the point of release than females) and vegetation cover was the only significant predictor of mean turning angle (i.e., increasing vegetation cover yielded more convoluted paths). Mice used logs to a greater extent on treatment plots (23.7%) than mice on control plots (4.8%). Mice on treatment plots used logs with less decay, less ground contact, and more bark than logs used by mice on control plots. Differences in log use patterns were largely a result of the attributes of available logs, but mice used logs selectively on treatment plots. Refuges were highly associated with woody debris, including refuges in rotting

  13. Effect of large amounts of dihydroxyacetone in the diet of rats.

    NASA Technical Reports Server (NTRS)

    Shapira, J.

    1972-01-01

    Experiments in which dihydroxyacetone (DHA) was used as nutrient for growing rats have not fulfilled the expectation that DHA could be used as a significant portion of the diet. Any attempt to treat major cerebral damage by prolonged administration of DHA is strongly contraindicated. For this reason, regenerated formose mixtures containing appreciable amounts of DHA will not be suitable as a significant portion of the diet for the crews of long-duration space missions.

  14. The ATLAS Eventindex: an event catalogue for experiments collecting large amounts of data

    NASA Astrophysics Data System (ADS)

    Barberis, D.; Cranshaw, J.; Dimitrov, G.; Favareto, A.; Fernández Casaní, Á.; González de la Hoz, S.; Hřivnáč, J.; Malon, D.; Nowak, M.; Salt Cairols, J.; Sánchez, J.; Sorokoletov, R.; Zhang, Q.; Atlas Collaboration

    2014-06-01

    Modern scientific experiments collect vast amounts of data that must be catalogued to meet multiple use cases and search criteria. In particular, high-energy physics experiments currently in operation produce several billion events per year. A database with the references to the files including each event in every stage of processing is necessary in order to retrieve the selected events from data storage systems. The ATLAS EventIndex project is studying the best way to store the necessary information using modern data storage technologies (Hadoop, HBase etc.) that allow saving in memory key-value pairs and select the best tools to support this application from the point of view of performance, robustness and ease of use. This paper describes the initial design and performance tests and the project evolution towards deployment and operation during 2014.

  15. Computation of scattering matrix elements of large and complex shaped absorbing particles with multilevel fast multipole algorithm

    NASA Astrophysics Data System (ADS)

    Wu, Yueqian; Yang, Minglin; Sheng, Xinqing; Ren, Kuan Fang

    2015-05-01

    Light scattering properties of absorbing particles, such as the mineral dusts, attract a wide attention due to its importance in geophysical and environment researches. Due to the absorbing effect, light scattering properties of particles with absorption differ from those without absorption. Simple shaped absorbing particles such as spheres and spheroids have been well studied with different methods but little work on large complex shaped particles has been reported. In this paper, the surface Integral Equation (SIE) with Multilevel Fast Multipole Algorithm (MLFMA) is applied to study scattering properties of large non-spherical absorbing particles. SIEs are carefully discretized with piecewise linear basis functions on triangle patches to model whole surface of the particle, hence computation resource needs increase much more slowly with the particle size parameter than the volume discretized methods. To improve further its capability, MLFMA is well parallelized with Message Passing Interface (MPI) on distributed memory computer platform. Without loss of generality, we choose the computation of scattering matrix elements of absorbing dust particles as an example. The comparison of the scattering matrix elements computed by our method and the discrete dipole approximation method (DDA) for an ellipsoid dust particle shows that the precision of our method is very good. The scattering matrix elements of large ellipsoid dusts with different aspect ratios and size parameters are computed. To show the capability of the presented algorithm for complex shaped particles, scattering by asymmetry Chebyshev particle with size parameter larger than 600 of complex refractive index m = 1.555 + 0.004 i and different orientations are studied.

  16. The Dark-Purple Tea Cultivar 'Ziyan' Accumulates a Large Amount of Delphinidin-Related Anthocyanins.

    PubMed

    Lai, Yun-Song; Li, Sha; Tang, Qian; Li, Huan-Xiu; Chen, Shen-Xiang; Li, Pin-Wu; Xu, Jin-Yi; Xu, Yan; Guo, Xiang

    2016-04-06

    Recently, we developed a novel tea cultivar 'Ziyan' with distinct purple leaves. There was a significant correlation between leaf color and anthocyanin pigment content in the leaves. A distinct allocation of metabolic flow for B-ring trihydroxylated anthocyanins and catechins in 'Ziyan' was observed. Delphinidin, cyanidin, and pelargonidin (88.15 mg/100 g FW in total) but no other anthocyanin pigments were detected in 'Ziyan', and delphinidin (70.76 mg/100 g FW) was particularly predominant. An analysis of the catechin content in 'Ziyan' and eight other cultivars indicated that 'Ziyan' exhibits a preference for synthesizing B-ring trihydroxylated catechins (with a proportion of 74%). The full-length cDNA sequences of flavonoid pathway genes were isolated by RNA-Seq coupled with conventional TA cloning, and their expression patterns were characterized. Purple-leaved cultivars had lower amounts of total catechins, polyphenols, and water extract than ordinary non-anthocyanin cultivars but similar levels of caffeine. Because dark-purple-leaved Camellia species are rare in nature, this study provides new insights into the interplay between the accumulations of anthocyanins and other bioactive components in tea leaves.

  17. 26 CFR 301.6867-1 - Presumptions where owner of large amount of cash is not identified.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... cash is not identified. 301.6867-1 Section 301.6867-1 Internal Revenue INTERNAL REVENUE SERVICE..., Bankruptcy, and Receiverships Jeopardy § 301.6867-1 Presumptions where owner of large amount of cash is not... 6861 (relating to jeopardy assessments), if cash in excess of $10,000 is found in the...

  18. Large negative Goos-Hänchen shift from a weakly absorbing dielectric slab.

    PubMed

    Wang, Li-Gang; Chen, Hong; Zhu, Shi-Yao

    2005-11-01

    It is theoretically shown that the negative Goos-Hänchen shifts near resonance, Re[k(z)d] = m pi, can be an order of magnitude larger than the wavelength for both TE- and TM-polarized beams reflected from a weakly absorbing dielectric slab if the absorption of the slab is sufficiently weak, which is different from the case for a lossless dielectric slab [Phys. Rev. Lett. 91, 133903 (2003)].

  19. Large flux change due to the intervening cold absorbers in NGC 3516

    NASA Astrophysics Data System (ADS)

    Nogami, K.; Negoro, H.; Hong, S.; Mihara, T.

    2004-06-01

    NGC3516 in the low flux state shows a flat energy spectrum (photon index ~1) and an intense narrow iron line. Such spectra are also observed in other Seyfert galaxies, and a broad bump structure around 6 keV above the 'flat' power-law spectrum has been interpreted as the gravitationally red-shifted iron line, disk reflection, or cold and/or warm absorbers. However, six years if BeppoSAX observations, including our latest three ones in 2001, clearly demonstrate that energy spectra above 20 keV always exhibit steep power-laws with photon indices ~2, and the flux changes only by a factor of 2, while the soft X-ray flux by a factor of ~10. From this fact, using BeppoSAX and ASCA data, we have concluded that the flat spectrum results from reprocessed, and partially covered power-laws with Γ~1.8 by warm matter nearby the central source and a cold absorber moved in the line of sight, respectively, and that the broad iron line and disk reflection components are less significant than one ever thought. Thus, the long-term spectral variations can be considered by intervening absorbers rather than changes in the accretion rate.

  20. 18O depletion in monsoon rain relates to large scale organized convection rather than the amount of rainfall.

    PubMed

    Lekshmy, P R; Midhun, M; Ramesh, R; Jani, R A

    2014-07-11

    Oxygen isotopic variations in rainfall proxies such as tree rings and cave calcites from South and East Asia have been used to reconstruct past monsoon variability, mainly through the amount effect: the observed (18)O depletion of rain with increasing amount, manifested as a negative correlation of the monthly amount of tropical rain with its δ(18)O, both measured at the same station. This relation exhibits a significant spatial variability, and at some sites (especially North-East and peninsular India), the rainfall proxies are not interpretable by this effect. We show here that relatively higher (18)O-depletion in monsoon rain is not related necessarily to its amount, but rather, to large scale organized convection. Presenting δ(18)O analyses of ~654 samples of daily rain collected during summer 2012 across 9 stations in Kerala, southern India, we demonstrate that although the cross correlations between the amounts of rainfall in different stations is insignificant, the δ(18)O values of rain exhibit highly coherent variations (significant at P = 0.05). Significantly more (18)O-depletion in the rain is caused by clouds only during events with a large spatial extent of clouds observable over in the south eastern Arabian Sea.

  1. Boreal Forests Sequester Large Amounts of Mercury over Millennial Time Scales in the Absence of Wildfire.

    PubMed

    Giesler, Reiner; Clemmensen, Karina E; Wardle, David A; Klaminder, Jonatan; Bindler, Richard

    2017-03-07

    Alterations in fire activity due to climate change and fire suppression may have profound effects on the balance between storage and release of carbon (C) and associated volatile elements. Stored soil mercury (Hg) is known to volatilize due to wildfires and this could substantially affect the land-air exchange of Hg; conversely the absence of fires and human disturbance may increase the time period over which Hg is sequestered. Here we show for a wildfire chronosequence spanning over more than 5000 years in boreal forest in northern Sweden that belowground inventories of total Hg are strongly related to soil humus C accumulation (R(2) = 0.94, p < 0.001). Our data clearly show that northern boreal forest soils have a strong sink capacity for Hg, and indicate that the sequestered Hg is bound in soil organic matter pools accumulating over millennia. Our results also suggest that more than half of the Hg stock in the sites with the longest time since fire originates from deposition predating the onset of large-scale anthropogenic emissions. This study emphasizes the importance of boreal forest humus soils for Hg storage and reveals that this pool is likely to persist over millennial time scales in the prolonged absence of fire.

  2. Management of large segmental tibial defects using locking IM nail and absorbable mesh

    PubMed Central

    Whately, Chris; Abdallah, Mohamed Attia; Alwatari, Yahya Ahmed

    2013-01-01

    Tibia accounts for the majority of open fractures with long segmental defects. The management of such defects imposes several challenges due to their associations with extensive soft tissue damage and high infection risk. In this report, we describe a new technique for the reconstruction of tibia in a young patient with 10 cm defect. The patient had a history of Gustilo Anderson type IIIB open fracture following a motorcycle accident. He was initially managed with multiple debridements and application of an external fixator. The defect was treated with the insertion of an antibiotic-coated intramedullary nail along with posterolateral bone grafting using an absorbable mesh. Six months postoperative, radiological assessment showed excellent callus formation diffusely around the intramedullary nail along with optimal alignment. The preliminary follow-up data are quite encouraging and the technique described in our case can be considered as a reasonable option in managing long segmental bone defects. PMID:23887993

  3. Antibody recognition of the glycoprotein g of viral haemorrhagic septicemia virus (VHSV) purified in large amounts from insect larvae

    PubMed Central

    2011-01-01

    Background There are currently no purification methods capable of producing the large amounts of fish rhabdoviral glycoprotein G (gpG) required for diagnosis and immunisation purposes or for studying structure and molecular mechanisms of action of this molecule (ie. pH-dependent membrane fusion). As a result of the unavailability of large amounts of the gpG from viral haemorrhagic septicaemia rhabdovirus (VHSV), one of the most dangerous viruses affecting cultured salmonid species, research interests in this field are severely hampered. Previous purification methods to obtain recombinant gpG from VHSV in E. coli, yeast and baculovirus grown in insect cells have not produced soluble conformations or acceptable yields. The development of large-scale purification methods for gpGs will also further research into other fish rhabdoviruses, such as infectious haematopoietic necrosis virus (IHNV), spring carp viremia virus (SVCV), hirame rhabdovirus (HIRRV) and snakehead rhabdovirus (SHRV). Findings Here we designed a method to produce milligram amounts of soluble VHSV gpG. Only the transmembrane and carboxy terminal-deleted (amino acid 21 to 465) gpG was efficiently expressed in insect larvae. Recognition of G21-465 by ß-mercaptoethanol-dependent neutralizing monoclonal antibodies (N-MAbs) and pH-dependent recognition by sera from VHSV-hyperimmunized or VHSV-infected rainbow trout (Oncorhynchus mykiss) was demonstrated. Conclusions Given that the purified G21-465 conserved some of its most important properties, this method might be suitable for the large-scale production of fish rhabdoviral gpGs for use in diagnosis, fusion and antigenicity studies. PMID:21693048

  4. Large and negative Goos-Hänchen shift near the Brewster dip on reflection from weakly absorbing media.

    PubMed

    Lai, H M; Chan, S W

    2002-05-01

    Applying Artmann's formula to a light beam in the TM state of wave polarization, we show analytically the existence of a large and negative Goos-Hänchen shift near the angle of the Brewster dip on reflection from a weakly absorbing semi-infinite medium. The shift is opposite that in the case of total internal reflection, and it can be an order of magnitude larger than a wavelength if the absorption of the reflecting medium is sufficiently weak. Examples are given, and the detectibility of the shift is discussed.

  5. Large and negative Goos-Hanchen shift near the Brewster dip on reflection from weakly absorbing media

    NASA Astrophysics Data System (ADS)

    Lai, H. M.; Chan, S. W.

    2002-05-01

    Applying Artmann's formula to a light beam in the TM state of wave polarization, we show analytically the existence of a large and negative Goos-Hanchen shift near the angle of the Brewster dip on reflection from a weakly absorbing semi-infinite medium. The shift is opposite that in the case of total internal reflection, and it can be an order of magnitude larger than a wavelength if the absorption of the reflecting medium is sufficiently weak. Examples are given, and the detectibility of the shift is discussed.

  6. Discovering meaningful information from large amounts of environment and health data to reduce uncertainties in formulating environmental policies.

    PubMed

    Lee, I-Nong; Chang, Wen-Chung; Hong, Yu-Jue; Liao, Shang-Chih

    2006-12-01

    This study uses knowledge discovery concepts to analyze large amounts of data step by step for the purpose of assisting in the formulation of environmental policy. We performed data cleansing and extracting from existing nation-wide databases, and used regression and classification techniques to analyze the data. The current water hardness in Kaohsiung, Taiwan contributes to the prevention of cardiovascular disease (CVD) but exacerbates the development of renal stones (RS). However, to focus on water hardness alone to control RS would not be cost effective at all, because the existing database parameters do not adequately allow for a clear understanding of RS. Analysis of huge amounts of data can most often turn up the most reliable and convincing results and the use of existing databases can be cost-effective.

  7. The negative binomial-Lindley distribution as a tool for analyzing crash data characterized by a large amount of zeros.

    PubMed

    Lord, Dominique; Geedipally, Srinivas Reddy

    2011-09-01

    The modeling of crash count data is a very important topic in highway safety. As documented in the literature, given the characteristics associated with crash data, transportation safety analysts have proposed a significant number of analysis tools, statistical methods and models for analyzing such data. Among the data issues, we find the one related to crash data which have a large amount of zeros and a long or heavy tail. It has been found that using this kind of dataset could lead to erroneous results or conclusions if the wrong statistical tools or methods are used. Thus, the purpose of this paper is to introduce a new distribution, known as the negative binomial-Lindley (NB-L), which has very recently been introduced for analyzing data characterized by a large number of zeros. The NB-L offers the advantage of being able to handle this kind of datasets, while still maintaining similar characteristics as the traditional negative binomial (NB). In other words, the NB-L is a two-parameter distribution and the long-term mean is never equal to zero. To examine this distribution, simulated and observed data were used. The results show that the NB-L can provide a better statistical fit than the traditional NB for datasets that contain a large amount of zeros.

  8. Metabolic and Microbial Modulation of the Large Intestine Ecosystem by Non-Absorbed Diet Phenolic Compounds: A Review.

    PubMed

    Mosele, Juana I; Macià, Alba; Motilva, Maria-José

    2015-09-18

    Phenolic compounds represent a diverse group of phytochemicals whose intake is associated with a wide spectrum of health benefits. As consequence of their low bioavailability, most of them reach the large intestine where, mediated by the action of local microbiota, a series of related microbial metabolites are accumulated. In the present review, gut microbial transformations of non-absorbed phenolic compounds are summarized. Several studies have reached a general consensus that unbalanced diets are associated with undesirable changes in gut metabolism that could be detrimental to intestinal health. In terms of explaining the possible effects of non-absorbed phenolic compounds, we have also gathered information regarded their influence on the local metabolism. For this purpose, a number of issues are discussed. Firstly, we consider the possible implications of phenolic compounds in the metabolism of colonic products, such as short chain fatty acids (SCFA), sterols (cholesterol and bile acids), and microbial products of non-absorbed proteins. Due to their being recognized as affective antioxidant and anti-inflammatory agents, the ability of phenolic compounds to counteract or suppress pro-oxidant and/or pro-inflammatory responses, triggered by bowel diseases, is also presented. The modulation of gut microbiota through dietetic maneuvers including phenolic compounds is also commented on. Although the available data seems to assume positive effects in terms of gut health protection, it is still insufficient for solid conclusions to be extracted, basically due to the lack of human trials to confirm the results obtained by the in vitro and animal studies. We consider that more emphasis should be focused on the study of phenolic compounds, particularly in their microbial metabolites, and their power to influence different aspects of gut health.

  9. Damped Ly alpha absorbers at high redshift: Large disks or galactic building blocks?

    NASA Technical Reports Server (NTRS)

    Haehnelt, Martin G.; Steinmetz, Matthias; Rauch, Michael

    1997-01-01

    The nature of the physical structures giving rise to damped Lyman alpha absorption systems (DLAS) at high redshifts is investigated. The proposal that rapidly rotating large disks are the only viable explanation for the observed asymmetric profiles of low ionization absorption lines is examined. Using hydrodynamic simulations of galaxy formation, it is demonstated that irregular protogalactic clumps can reproduce the observed velocity width distribution and asymmetries of the absorption profiles equally well. The velocity broadening in the simulated clumps is due to a mixture of rotation, random motions, infall and merging. The observed velocity width correlates with the virial velocity for the dark matter halo of the forming protogalactic clump. The typical virial velocity of the halos required to lead to the DLAS population is approximately 100 km/s. It is concluded that the evidence that DLAS at high redshift are related to large, rapidly rotating disks, is not compelling.

  10. [Irradiation of lymphogranulomatosis patients with large fields of complex configuration, calculating absorbed doses by microcomputer].

    PubMed

    Belyĭ, E K; Miasnikov, A A; Mendeleev, I M

    1985-01-01

    The authors demonstrated advantages of irradiating lymphogranulomatosis patients with large fields of complex configuration. The use of computer eliminates the difficulties of dosage calculation. Application for these purposes of the 15 VUMS-28 unit based on the microcomputer "Elektronika-60" is suggested. Algorithm of the dosage calculation program is presented. The program is drawn up according to the GOST so that it can be used by other institutions concerned.

  11. Impacts of Large Amounts of Wind Power on Design and Operation of Power Systems; Results of IEA Collaboration

    SciTech Connect

    Parsons, B.; Ela, E.; Holttinen, H.; Meibom, P.; Orths, A.; O'Malley, M.; Ummels, B. C.; Tande, J.; Estanqueiro, A.; Gomez, E.; Smith, J. C.

    2008-06-01

    There are a multitude of studies completed and ongoing related to the cost of wind integration. However, the results are not easy to compare. An international forum for exchange of knowledge of power system impacts of wind power has been formed under the IEA Implementing Agreement on Wind Energy. IEA WIND R&D Task 25 on “Design and Operation of Power Systems with Large Amounts of Wind Power” produced a state-of-the-art report in October 2007, where the most relevant wind-power grid integration studies were analyzed, especially regarding methodologies and input data. This paper summarizes the results from 18 case studies, with discussion on differences in methodology as well as issues that have been identified to impact the cost of wind integration.

  12. Impacts of Large Amounts of Wind Power on Design and Operation of Power Systems, Results of IEA Collaboration

    SciTech Connect

    Holttinen, H.; Meibom, P.; Orths, A.; O'Malley, M.; Ummels, B. C.; Tande, J. O.; Estanqueiro, A.; Gomez, E.; Smith, J. C.; Ela, E.

    2008-01-01

    There are a multitude of studies completed and ongoing related to the cost of wind integration. However, the results are not easy to compare. An international forum for exchange of knowledge of power system impacts of wind power has been formed under the IEA Implementing Agreement on Wind Energy. IEA WIND R and D Task 25 on 'Design and Operation of Power Systems with Large Amounts of Wind Power' produced a state-of-the-art report in October 2007, where the most relevant wind-power grid integration studies were analyzed, especially regarding methodologies and input data. This paper summarizes the results from 18 case studies, with discussion on differences in methodology as well as issues that have been identified to impact the cost of wind integration.

  13. Precisions Measurement for the Grasp of Welding Deformation amount of Time Series for Large-Scale Industrial Products

    NASA Astrophysics Data System (ADS)

    Abe, R.; Hamada, K.; Hirata, N.; Tamura, R.; Nishi, N.

    2015-05-01

    As well as the BIM of quality management in the construction industry, demand for quality management of the manufacturing process of the member is higher in shipbuilding field. The time series of three-dimensional deformation of the each process, and are accurately be grasped strongly demanded. In this study, we focused on the shipbuilding field, will be examined three-dimensional measurement method. The shipyard, since a large equipment and components are intricately arranged in a limited space, the installation of the measuring equipment and the target is limited. There is also the element to be measured is moved in each process, the establishment of the reference point for time series comparison is necessary to devise. In this paper will be discussed method for measuring the welding deformation in time series by using a total station. In particular, by using a plurality of measurement data obtained from this approach and evaluated the amount of deformation of each process.

  14. High concentration two-stage optics for parabolic trough solar collectors with tubular absorber and large rim angle

    SciTech Connect

    Collares-Pereira, M. ); Gordon, J.M. ); Rabl, A. ); Winston, R. )

    1991-01-01

    A new two-stage optical design is proposed for parabolic trough solar collectors with tubular absorbers. It can boost the concentration ratio by a factor of 2.5 relative to the conventional design, while maintaining the large rim angles (i.e., low nominal f-numbers) that are desirable for practical and economical reasons. The second state involves asymmetric nonimaging concentrators of the CPC type, facing segments of the parabolic first stage. The second stage can be accommodated inside an evacuated receiver, allowing the use of first-surface silvered reflectors. The low heat loss of this design opens the possibility of producing steam at temperatures and pressures of conventional power plants, using only one-axis tracking. The improvement in conversion efficiency would be substantial.

  15. A Very Large Array search for emission from HI associated with nearby Lyman alpha absorbers

    NASA Technical Reports Server (NTRS)

    Van Gorkom, J. H.; Bahcall, J. N.; Jannuzi, B. T.; Schneider, D. P.

    1993-01-01

    We present a sensitive Very Large Array (VLA) search for H I emission from the vicinity of the Lyman alpha clouds in the Virgo Cluster, which were recently discovered with Hubble Space Telescope (HST) in absorption toward the nearest quasar 3C273. We searched an area of 40 by 40 arcmin centered on 3C273, covering a velocity range from 840 to 1840 km/s. The bandpass was self-calibrated on 3C273 leading to a spectral dynamic range of better than 10(exp 5) to 1. No H I was detected. The rms noise in the final images corresponds to a 3 sigma column density sensitivity of 2.8 x 10(exp 19) sq cm on scales of a few kpc. Small H I clouds could have been detected down to a few times 10(exp 6) solar mass. Our failure to detect H I emission at the higher column densities sets a lower limit to the radius of the Lyman alpha clouds of 3.9 kpc, assuming a spherical geometry.

  16. Response attenuation in a large-scale structure subjected to blast excitation utilizing a system of essentially nonlinear vibration absorbers

    NASA Astrophysics Data System (ADS)

    Wierschem, Nicholas E.; Hubbard, Sean A.; Luo, Jie; Fahnestock, Larry A.; Spencer, Billie F.; McFarland, D. Michael; Quinn, D. Dane; Vakakis, Alexander F.; Bergman, Lawrence A.

    2017-02-01

    Limiting peak stresses and strains in a structure subjected to high-energy, short-duration transient loadings, such as blasts, is a challenging problem, largely due to the well-known insensitivity of the first few cycles of the structural response to damping. Linear isolation, while a potential solution, requires a very low fundamental natural frequency to be effective, resulting in large nearly-rigid body displacement of the structure, while linear vibration absorbers have little or no effect on the early-time response where relative motions, and thus stresses and strains, are at their highest levels. The problem has become increasingly important in recent years with the expectation of blast-resistance as a design requirement in new construction. In this paper, the problem is examined experimentally and computationally in the context of offset-blast loading applied to a custom-built nine story steel frame structure. A fully-passive response mitigation system consisting of six lightweight, essentially nonlinear vibration absorbers (termed nonlinear energy sinks - NESs) is optimized and deployed on the upper two floors of this structure. Two NESs have vibro-impact nonlinearities and the other four possess smooth but essentially nonlinear stiffnesses. Results of the computational and experimental study demonstrate the efficacy of the proposed passive nonlinear mitigation system to rapidly and efficiently attenuate the global structural response, even at early time (i.e., starting at the first response cycle), thus minimizing the peak demand on the structure. This is achieved by nonlinear redistribution of the blast energy within the modal space through low-to-high energy scattering due to the action of the NESs. The experimental results validate the theoretical predictions.

  17. Large-scale structures in tetrahydrofuran-water mixture with a trace amount of antioxidant butylhydroxytoluene (BHT).

    PubMed

    Li, Zhiyong; Cheng, He; Li, Junyu; Hao, Jinkun; Zhang, Li; Hammouda, Boualem; Han, Charles C

    2011-06-23

    Author: Because of the closed-loop phase diagram of tetrahydrofuran (THF)-water mixture, THF aqueous solution naturally exhibits concentration fluctuations near the phase boundary. Besides the fast mode induced by concentration fluctuations, the 4.5% mole fraction THF aqueous solution is also characterized by a slow mode. The existence of a trace amount of butylhydroxytoluene (BHT) antioxidant in commercial THF strongly influences the slow mode in 4.5% mole fraction THF aqueous solution. A core-shell structure with a BHT core and a shell made from THF-rich THF-D(2)O mixture was identified by the combination of dynamic laser light scattering (DLS) and small-angle neutron scattering (SANS). BHT is hydrophobic, stabilized by a THF-rich domain in THF aqueous solution and acts as a tracer to make the large-scale structure (slow mode) "visible" through SANS because of its larger contrast with the solvent. In contrast, this large-scale structure was almost not detectable by SANS when BHT was removed from the THF-D(2)O mixture. Combined UV-vis, DLS, and static light scattering (SLS) indicated that slow-moving objects do exist and that their sizes almost do not change, but their concentration decreases to a small but nonzero value at the infinite dilution limit. The origin of the elusive large-scale structure at zero BHT concentration is still not clear, but it might be associated with some hydrophobic impurities or nanobubbles. However, a polydisperse sphere model of ∼8.5% mole fraction THF-D(2)O mixture can fit the structure with a radius of ∼100 nm, which gives the temperature-dependent low-q SANS profiles of 4.5% mole fraction THF aqueous solution at zero BHT concentration.

  18. Lyα-emitting galaxies as a probe of reionization: large-scale bubble morphology and small-scale absorbers

    NASA Astrophysics Data System (ADS)

    Kakiichi, Koki; Dijkstra, Mark; Ciardi, Benedetta; Graziani, Luca

    2016-12-01

    The visibility of Lyα-emitting galaxies during the Epoch of Reionization is controlled by both diffuse H I patches in large-scale bubble morphology and small-scale absorbers. To investigate their impacts on Lyα transfer, we apply a novel combination of analytic modelling and cosmological hydrodynamical, radiative transfer simulations to three reionization models: (i) the `bubble' model, where only diffuse H I outside ionized bubbles is present; (ii) the `web' model, where H I exists only in overdense self-shielded gas; and (iii) the hybrid `web-bubble' model. The three models can explain the observed Lyα luminosity function equally well, but with very different H I fractions. This confirms a degeneracy between the ionization topology of the intergalactic medium (IGM) and the H I fraction inferred from Lyα surveys. We highlight the importance of the clustering of small-scale absorbers around galaxies. A combined analysis of the Lyα luminosity function and the Lyα fraction can break this degeneracy and provide constraints on the reionization history and its topology. Constraints can be improved by analysing the full MUV-dependent redshift evolution of the Lyα fraction of Lyman break galaxies. We find that the IGM-transmission probability distribution function is unimodal for bubble models and bimodal in web models. Comparing our models to observations, we infer that the neutral fraction at z ˜ 7 is likely to be of the order of tens of per cent when interpreted with bubble or web-bubble models, with a conservative lower limit ˜1 per cent when interpreted with web models.

  19. Design and Operation of Power Systems with Large Amounts of Wind Power, First Results of IEA Collaboration

    SciTech Connect

    Holttinen, H.; Meibom, P.; Orths, A.; Van Hulle, F.; Ensslin, C.; Hofmann, L.; McCann, J.; Pierik, J.; Tande, J. O.; Estanqueiro, A.; Soder, L.; Strbac, G.; Parsons, B.; Smith, J. C.; Lemstrom, B.

    2006-01-01

    An international forum for exchange of knowledge of power system impacts of wind power has been formed under the IEA Implementing Agreement on Wind Energy. The task 'Design and Operation of Power Systems with Large Amounts of Wind Power' will analyse existing case studies from different power systems. There are a multitude of studies made and ongoing related to cost of wind integration. However, the results are not easy to compare. This paper summarizes the results from 10 countries and outlines the studies made at European Wind Energy Association and the European system operators UCTE and ETSO. A more in-depth review of the studies is needed to draw conclusions on the range of integration costs for wind power. A state-of-the art review process of the new IEA collaboration will seek reasons behind the wide range of results for costs of wind integration - definitions for wind penetration, reserves and costs; different power system and load characteristics and operational rules; underlying assumptions on variability and uncertainty of wind, etc.

  20. Soil sampling and isolation of extracellular DNA from large amount of starting material suitable for metabarcoding studies.

    PubMed

    Taberlet, Pierre; Prud'Homme, Sophie M; Campione, Etienne; Roy, Julien; Miquel, Christian; Shehzad, Wasim; Gielly, Ludovic; Rioux, Delphine; Choler, Philippe; Clément, Jean-Christophe; Melodelima, Christelle; Pompanon, François; Coissac, Eric

    2012-04-01

    DNA metabarcoding refers to the DNA-based identification of multiple species from a single complex and degraded environmental sample. We developed new sampling and extraction protocols suitable for DNA metabarcoding analyses targeting soil extracellular DNA. The proposed sampling protocol has been designed to reduce, as much as possible, the influence of local heterogeneity by processing a large amount of soil resulting from the mixing of many different cores. The DNA extraction is based on the use of saturated phosphate buffer. The sampling and extraction protocols were validated first by analysing plant DNA from a set of 12 plots corresponding to four plant communities in alpine meadows, and, second, by conducting pilot experiments on fungi and earthworms. The results of the validation experiments clearly demonstrated that sound biological information can be retrieved when following these sampling and extraction procedures. Such a protocol can be implemented at any time of the year without any preliminary knowledge of specific types of organisms during the sampling. It offers the opportunity to analyse all groups of organisms using a single sampling/extraction procedure and opens the possibility to fully standardize biodiversity surveys.

  1. High Reynolds Number Investigation of a Flush-Mounted, S-Duct Inlet With Large Amounts of Boundary Layer Ingestion

    NASA Technical Reports Server (NTRS)

    Berrier, Bobby L.; Carter, Melissa B.; Allan, Brian G.

    2005-01-01

    An experimental investigation of a flush-mounted, S-duct inlet with large amounts of boundary layer ingestion has been conducted at Reynolds numbers up to full scale. The study was conducted in the NASA Langley Research Center 0.3-Meter Transonic Cryogenic Tunnel. In addition, a supplemental computational study on one of the inlet configurations was conducted using the Navier-Stokes flow solver, OVERFLOW. Tests were conducted at Mach numbers from 0.25 to 0.83, Reynolds numbers (based on aerodynamic interface plane diameter) from 5.1 million to 13.9 million (full-scale value), and inlet mass-flow ratios from 0.29 to 1.22, depending on Mach number. Results of the study indicated that increasing Mach number, increasing boundary layer thickness (relative to inlet height) or ingesting a boundary layer with a distorted profile decreased inlet performance. At Mach numbers above 0.4, increasing inlet airflow increased inlet pressure recovery but also increased distortion. Finally, inlet distortion was found to be relatively insensitive to Reynolds number, but pressure recovery increased slightly with increasing Reynolds number.

  2. High Reynolds Number Investigation of a Flush Mounted, S-Duct Inlet With Large Amounts of Boundary Layer Ingestion

    NASA Technical Reports Server (NTRS)

    Berrier, Bobby L.; Carter, Melissa B.; Allan, Brian G.

    2005-01-01

    An experimental investigation of a flush-mounted, S-duct inlet with large amounts of boundary layer ingestion has been conducted at Reynolds numbers up to full scale. The study was conducted in the NASA Langley Research Center 0.3-Meter Transonic Cryogenic Tunnel. In addition, a supplemental computational study on one of the inlet configurations was conducted using the Navier-Stokes flow solver, OVERFLOW. Tests were conducted at Mach numbers from 0.25 to 0.83, Reynolds numbers (based on aerodynamic interface plane diameter) from 5.1 million to 13.9 million (full-scale value), and inlet mass-flow ratios from 0.29 to 1.22, depending on Mach number. Results of the study indicated that increasing Mach number, increasing boundary layer thickness (relative to inlet height) or ingesting a boundary layer with a distorted profile decreased inlet performance. At Mach numbers above 0.4, increasing inlet airflow increased inlet pressure recovery but also increased distortion. Finally, inlet distortion was found to be relatively insensitive to Reynolds number, but pressure recovery increased slightly with increasing Reynolds number.This CD-ROM supplement contains inlet data including: Boundary layer data, Duct static pressure data, performance-AIP (fan face) data, Photos, Tunnel wall P-PTO data and definitions.

  3. Mode-locked ytterbium fiber lasers using a large modulation depth carbon nanotube saturable absorber without an additional spectral filter

    NASA Astrophysics Data System (ADS)

    Pan, Y. Z.; Miao, J. G.; Liu, W. J.; Huang, X. J.; Wang, Y. B.

    2014-09-01

    We demonstrate an all-normal-dispersion ytterbium (Yb)-doped fiber laser mode-locked by a higher modulation depth carbon nanotube saturable absorber (CNT-SA) based on an evanescent field interaction scheme. The laser cavity consists of pure normal dispersion fibers without dispersion compensation and an additional spectral filter. It is exhibited that the higher modulation depth CNT-SA could contribute to stabilize the mode-locking operation within a limited range of pump power and generate the highly chirped pulses with a high-energy level in the cavity with large normal dispersion and strong nonlinearity. Stable mode-locked pulses with a maximal energy of 29 nJ with a 5.59 MHz repetition rate at the operating wavelength around 1085 nm have been obtained. The maximal time-bandwidth product is 262.4. The temporal and spectral characteristics of pulses versus pump power are demonstrated. The experimental results suggest that the CNT-SA provides a sufficient nonlinear loss to compensate high nonlinearity and catch up the gain at a different pump power and thus leads to the stable mode locking.

  4. Composition for absorbing hydrogen

    DOEpatents

    Heung, Leung K.; Wicks, George G.; Enz, Glenn L.

    1995-01-01

    A hydrogen absorbing composition. The composition comprises a porous glass matrix, made by a sol-gel process, having a hydrogen-absorbing material dispersed throughout the matrix. A sol, made from tetraethyl orthosilicate, is mixed with a hydrogen-absorbing material and solidified to form a porous glass matrix with the hydrogen-absorbing material dispersed uniformly throughout the matrix. The glass matrix has pores large enough to allow gases having hydrogen to pass through the matrix, yet small enough to hold the particles dispersed within the matrix so that the hydrogen-absorbing particles are not released during repeated hydrogen absorption/desorption cycles.

  5. Composition for absorbing hydrogen

    DOEpatents

    Heung, L.K.; Wicks, G.G.; Enz, G.L.

    1995-05-02

    A hydrogen absorbing composition is described. The composition comprises a porous glass matrix, made by a sol-gel process, having a hydrogen-absorbing material dispersed throughout the matrix. A sol, made from tetraethyl orthosilicate, is mixed with a hydrogen-absorbing material and solidified to form a porous glass matrix with the hydrogen-absorbing material dispersed uniformly throughout the matrix. The glass matrix has pores large enough to allow gases having hydrogen to pass through the matrix, yet small enough to hold the particles dispersed within the matrix so that the hydrogen-absorbing particles are not released during repeated hydrogen absorption/desorption cycles.

  6. Investigation of Cement-Replacement Materials. Report 10. Use of Large Amounts of Possolans in Lean Mass Concrete.

    DTIC Science & Technology

    proportioned with crushed limestone aggregate graded up to 6 in. Five mixtures contained no pozzolan and from 189 to 312 lb of portland cement per cubic...yard. Thirty-three mixtures contained one bag (94 lb) of portland cement per cubic yard with various amounts of one of four pozzolanic materials. A...greater weight of pozzolan than of portland cement was used in 24 of the 33 mixtures. Many of the mixtures appeared to develop ample strength and

  7. SN 2010mb: Direct evidence for a supernova interacting with a large amount of hydrogen-free circumstellar material

    SciTech Connect

    Ben-Ami, Sagi; Gal-Yam, Avishay; Rabinak, Itay; Yaron, Ofer; Arcavi, Iair; Ofek, Eran O.; Mazzali, Paolo A.; Gnat, Orly; Modjaz, Maryam; Sullivan, Mark; Bildsten, Lars; Poznanski, Dovi; Bloom, Joshua S.; Nugent, Peter E.; Horesh, Assaf; Kulkarni, Shrinivas R.; Perley, Daniel; Kasliwal, Mansi M.; Quimby, Robert; Xu, Dong

    2014-04-10

    We present our observations of SN 2010mb, a Type Ic supernova (SN) lacking spectroscopic signatures of H and He. SN 2010mb has a slowly declining light curve (LC) (∼600 days) that cannot be powered by {sup 56}Ni/{sup 56}Co radioactivity, the common energy source for Type Ic SNe. We detect signatures of interaction with hydrogen-free circumstellar material including a blue quasi-continuum and, uniquely, narrow oxygen emission lines that require high densities (∼10{sup 9} cm{sup –3}). From the observed spectra and LC, we estimate that the amount of material involved in the interaction was ∼3 M {sub ☉}. Our observations are in agreement with models of pulsational pair-instability SNe described in the literature.

  8. Isolation and characterization of purple non-sulfur bacteria, Afifella marina, producing large amount of carotenoids from mangrove microhabitats.

    PubMed

    Kar Soon, Tan; Al-Azad, Sujjat; Ransangan, Julian

    2014-08-01

    This study determined the effect of light intensity and photoperiod on the dry cell weight and total amount of carotenoids in four isolates of purple non-sulfur bacteria obtained from shaded and exposed microhabitats of a mangrove ecosystem in Kota Kinabalu, Sabah, Malaysia. The initial isolation of the bacteria was carried out using synthetic 112 medium under anaerobic conditions (2.5 klx) at 30 ± 2°C. On the basis of colony appearance, cell morphology, gram staining, motility test, and 16S rRNA gene sequencing analyses, all four bacteria were identified as Afifella marina. One of the bacterial isolates, designated as Af. marina strain ME, which was extracted from an exposed mud habitat within the mangrove ecosystem, showed the highest yield in dry cell weight (4.32± 0.03 g/l) as well as total carotenoids (0.783 ± 0.002 mg/g dry cell weight). These values were significantly higher than those for dry cell weight (3.77 ± 0.02g/l ) and total carotenoid content (0.706 ± 0.008 mg/g) produced by the isolates from shaded habitats. Further analysis of the effect of 10 levels of light intensity on the growth characteristics of Af. marina strain ME showed that the optimum production of dry cell weight and total carotenoids was achieved at different light intensities and incubation periods. The bacterium produced the highest dry cell weight of 4.98 g/l at 3 klx in 72 h incubation, but the carotenoid production of 0.783 mg/g was achieved at 2.5 klx in 48 h incubation. Subsequent analysis of the effect of photoperiod on the production of dry cell weight and total carotenoids at optimum light intensities (3 and 2.5 klx, respectively) revealed that 18 and 24 h were the optimum photoperiods for the production of dry cell weight and total carotenoids, respectively. The unique growth characteristics of the Af. marina strain ME can be exploited for biotechnology applications.

  9. Monitoring feed amounts in goliath groupers (Epinephelus itajara) using behavioral conditioning in a large mixed species exhibit.

    PubMed

    Kittell, Michele M; Ratte, Magan E

    2008-09-01

    Goliath groupers (Epinephelus itajara) are large charismatic species, which are often residents in public aquaria. This study reports a novel approach to feeding techniques for three resident goliath groupers. Because of the size and depth of their exhibit, the groupers were conditioned to hand feed from aquarists. Daily food logs were recorded including the type and number of species, how often the groupers were fed, and how often they accepted the offered food. Mackerel, herring, and sardine represented the highest percentage of the diet, whereas capelin, squid, and shrimp were the lowest percentage. Over a one-year period, records showed that grouper 1 and grouper 3 ate fairly consistently throughout the year. Grouper 2 had a higher degree of variation in his monthly feeding average with a decrease from May to September and an increase through April. Grouper 1 and grouper 3 took food from the aquarists most consistently with a monthly average of 88.8+/-10.8 and 89.7+/-6.15% of the time, respectively. Grouper 2 was not as consistent, hand feeding at only 74.5+/-16.2% of the time offered. Diet management and behavioral conditioning with the goliath groupers have established consistent husbandry records and therefore better monitoring of the individual fish's long-term health status. Zoo Biol 27:414-419, 2008. (c) 2008 Wiley-Liss, Inc.

  10. Lipid-absorbing Polymers

    NASA Technical Reports Server (NTRS)

    Marsh, H. E., Jr.; Wallace, C. J.

    1973-01-01

    The removal of bile acids and cholesterol by polymeric absorption is discussed in terms of micelle-polymer interaction. The results obtained with a polymer composed of 75 parts PEO and 25 parts PB plus curing ingredients show an absorption of 305 to 309%, based on original polymer weight. Particle size effects on absorption rate are analyzed. It is concluded that crosslinked polyethylene oxide polymers will absorb water, crosslinked polybutadiene polymers will absorb lipids; neither polymer will absorb appreciable amounts of lipids from micellar solutions of lipids in water.

  11. [A case of acute ethanol intoxication with remarkable hyperglycemia by "ume-shu", a Japanese apricot liquor made with a large amount of sugar].

    PubMed

    Sugano, Takayuki; Kojima, Naoki; Kaneko, Susumu; Ishida, Junro; Terada, Taizo; Inagawa, Hiroshi; Okada, Yasusei

    2002-07-01

    A 19-year-old woman ingested 2.2 L of "umeshu", a Japanese apricot liquor made with a large amount of sugar. She was unconscious and in shock. The estimated blood ethanol concentration was 607 mg/dl, and the blood glucose level was 576 mg/dl. Because her respiration and circulation was highly suppressed, blood purification was indicated. Continuous hemodiafiltration (CHDF) was performed instead of hemodialysis because her hemodynamics was unstable. After CHDF was instituted, her blood glucose level reduced to normal range, and her consciousness became alert. CHDF was effective in eliminating ethanol and stabilizing her hemodynamics within an early stage. Though acute ethanol intoxication is known to inhibit glucogenesis, leading to hypoglycemia, marked hyperglycemia was seen in this case. Ingestion of a large amount of glucose-rich liquor and being in shock seemed to be the causes of hyperglycemia.

  12. Automated Absorber Attachment for X-ray Microcalorimeter Arrays

    NASA Technical Reports Server (NTRS)

    Moseley, S.; Allen, Christine; Kilbourne, Caroline; Miller, Timothy M.; Costen, Nick; Schulte, Eric; Moseley, Samuel J.

    2007-01-01

    Our goal is to develop a method for the automated attachment of large numbers of absorber tiles to large format detector arrays. This development includes the fabrication of high quality, closely spaced HgTe absorber tiles that are properly positioned for pick-and-place by our FC150 flip chip bonder. The FC150 also transfers the appropriate minute amount of epoxy to the detectors for permanent attachment of the absorbers. The success of this development will replace an arduous, risky and highly manual task with a reliable, high-precision automated process.

  13. Reversed-phase liquid chromatography using mandelic acid as an eluent for the determination of uranium in presence of large amounts of thorium.

    PubMed

    Jaison, P G; Telmore, Vijay M; Kumar, Pranaw; Aggarwal, Suresh K

    2009-02-27

    Studies were carried out for the separation of uranium (U) and thorium (Th) on reversed-phase (RP) C18 columns using mandelic acid as an eluent. Retention of thorium-mandelate on the unmodified stationary phase was found to be greater than that of uranyl-mandelate under the pH conditions employed. Th retention capacity of the stationary phase was determined as a function of pH and MeOH content of the mobile phase. The optimised parameters allowing U elution prior to Th were utilized for the determination of small amounts of U in the presence of large amounts of Th. The method has been used for the determination of U in synthetic samples with Th/U amount ratios up to 100,000 (10 microg/g of U) without any pre-separation, employing a particulate C18 column. Effect of concentration of ion interaction reagents (IIRs) on the retention was studied to understand the mechanism of adsorption of their mandelate complexes onto the stationary phase. The experiments conducted unequivocally prove that thorium-mandelate complex is neutral whereas uranyl-mandelate complex is anionic in nature.

  14. "Smart" Electromechanical Shock Absorber

    NASA Technical Reports Server (NTRS)

    Stokes, Lebarian; Glenn, Dean C.; Carroll, Monty B.

    1989-01-01

    Shock-absorbing apparatus includes electromechanical actuator and digital feedback control circuitry rather than springs and hydraulic damping as in conventional shock absorbers. Device not subject to leakage and requires little or no maintenance. Attenuator parameters adjusted in response to sensory feedback and predictive algorithms to obtain desired damping characteristic. Device programmed to decelerate slowly approaching vehicle or other large object according to prescribed damping characteristic.

  15. Performance evaluation of CFRP-rubber shock absorbers

    SciTech Connect

    Lamanna, Giuseppe Sepe, Raffaele

    2014-05-15

    In the present work a numerical investigation on the energy absorbing capability of dedicated structural components made of a carbon fiber reinforced polymer and an emulsion polymerised styrene butadiene rubber is reported. The shock absorbers are devices designed to absorb large amounts of energy by sacrificing their own structural integrity. Their aim is to cushion the effects of an impact phenomenon with the intent to preserve other structures from global failure or local damaging. Another important role of shock absorbers is reducing the peak of the acceleration showed during an impact phenomenon. This effect is of considerable interest in the case of vehicles to preserve passengers’ safety. Static and dynamic numerical results are compared with experimental ones in terms of mean crushing forces, energy and peak crushing. The global performance of the absorbers has been evaluated by referencing to a proposed quality index.

  16. Performance evaluation of CFRP-rubber shock absorbers

    NASA Astrophysics Data System (ADS)

    Lamanna, Giuseppe; Sepe, Raffaele

    2014-05-01

    In the present work a numerical investigation on the energy absorbing capability of dedicated structural components made of a carbon fiber reinforced polymer and an emulsion polymerised styrene butadiene rubber is reported. The shock absorbers are devices designed to absorb large amounts of energy by sacrificing their own structural integrity. Their aim is to cushion the effects of an impact phenomenon with the intent to preserve other structures from global failure or local damaging. Another important role of shock absorbers is reducing the peak of the acceleration showed during an impact phenomenon. This effect is of considerable interest in the case of vehicles to preserve passengers' safety. Static and dynamic numerical results are compared with experimental ones in terms of mean crushing forces, energy and peak crushing. The global performance of the absorbers has been evaluated by referencing to a proposed quality index.

  17. [Transcatheter Arterial Chemoembolization with Super absorbent Polymer Microspheres for a Large Lung Cystic Adenocarcinoma in the Left Pulmonary Cavity].

    PubMed

    Kennoki, Norifumi; Hori, Shinichi; Yuki, Takeo; Sueyoshi, Satoshi; Hori, Atsushi

    2015-11-01

    A 57-year-old woman presented with lung adenocarcinoma and carcinomatous pleurisy in January 2013. The primary lesion had been treated with 60-Gy radiation therapy. She, however, showed a recurrence of the tumor in her pulmonary cavity. She received systemic chemotherapy for 1 year but did not show any improvement. She visited our clinic in March 2014. Her performance level was 3. Her hemoglobin level was 8.5 g/dL. The CT scan showed that the size of the cystic tumor was 200 × 144 × 143 mm. The tumor severely compressed her heart. We performed TACE using a spherical embolic agent. The microcatheter was guided through the left bronchial artery; left intercostal artery 9, 10, and 11; and the left inferior phrenic artery. The anticancer drugs selected were CDDP and 5-FU. The embolic material used was SAP-MS. After 3 therapy sessions, the CT scan showed shrinkage of the target lesion to 100 × 93 × 54 mm. Her hemoglobin level increased to 13.8 g/dL; furthermore, the severity of dyspnea decreased, and she showed a performance status of 0. TACE with SAP-MS was successfully performed for the large cystic tumor in the pulmonary cavity that metastasized from the lung cancer and was refractory to standard treatments. After the treatment, the tumor size decreased and the patient's symptoms alleviated.

  18. A Deep Survey of Low-Redshift Absorbers and Their Connections with Galaxies: Probing the Roles of Dwarfs, Satellites, and Large-Scale Environment

    NASA Astrophysics Data System (ADS)

    Burchett, Joseph

    2014-10-01

    In the not-too-distant past, the study of galaxy evolution neglected the vast interface between the stars in a galaxy and intergalactic space except for the dynamical effects of dark matter. Thanks to QSO absorption line spectroscopy and the Cosmic Origins Spectrograph {COS}, the circumgalactic medium {CGM} has come into sharp focus as a rich ecosystem playing a vital role in the evolution of the host galaxy. However, attributing the gas detected in absorption with host dwarf galaxies detected in optical surveys around the sightline becomes very difficult very quickly with increasing redshift. In addition, both targeted UV spectroscopy and ground-based galaxy surveys are resource intensive, which complicates compiling large, statistically robust samples of very-low-redshift absorber/galaxy pairs. We propose a CGM study of unprecedented statistical power by exploiting the vast number of sightlines in the HST/COS archive located within the Sloan Digital Sky Survey {SDSS} footprint to compile an estimated sample of 586 absorbers at z<0.015. This very-low-redshift criterion enables spectroscopic completeness down to L<0.01 L* galaxies in publicly available optical imaging and spectroscopy.Our survey is uniquely poised to address the following questions: {1} What is the role of dwarf galaxies that would be undetectable at higher redshift in giving rise to the gas detected in QSO spectroscopy? {2} How does galaxy environment and large-scale structure affect the CGM and what are the implications for environmental quenching of star formation? {3} How efficiently do feedback mechanisms expel metal-enriched gas to great distances into the galaxy halo and into the IGM?

  19. Sound Absorbers

    NASA Astrophysics Data System (ADS)

    Fuchs, H. V.; Möser, M.

    Sound absorption indicates the transformation of sound energy into heat. It is, for instance, employed to design the acoustics in rooms. The noise emitted by machinery and plants shall be reduced before arriving at a workplace; auditoria such as lecture rooms or concert halls require a certain reverberation time. Such design goals are realised by installing absorbing components at the walls with well-defined absorption characteristics, which are adjusted for corresponding demands. Sound absorbers also play an important role in acoustic capsules, ducts and screens to avoid sound immission from noise intensive environments into the neighbourhood.

  20. Large Amounts of Reactivated Virus in Tears Precedes Recurrent Herpes Stromal Keratitis in Stressed Rabbits Latently Infected with Herpes Simplex Virus

    PubMed Central

    Perng, Guey-Chuen; Osorio, Nelson; Jiang, Xianzhi; Geertsema, Roger; Hsiang, Chinhui; Brown, Don; BenMohamed, Lbachir; Wechsler, Steven L.

    2017-01-01

    Aim Recurrent herpetic stromal keratitis (rHSK), due to an immune response to reactivation of herpes simplex virus (HSV-1), can cause corneal blindness. The development of therapeutic interventions such as drugs and vaccines to decrease rHSK have been hampered by the lack of a small and reliable animal model in which rHSK occurs at a high frequency during HSV-1 latency. The aim of this study is to develop a rabbit model of rHSK in which stress from elevated temperatures increases the frequency of HSV-1 reactivations and rHSK. Materials and methods Rabbits latently infected with HSV-1 were subjected to elevated temperatures and the frequency of viral reactivations and rHSK were determined. Results In an experiment in which rabbits latently infected with HSV-1 were subjected to ill-defined stress as a result of failure of the vivarium air conditioning system, reactivation of HSV-1 occurred at over twice the normal frequency. In addition, 60% of eyes developed severe rHSK compared to <1% of eyes normally. All episodes of rHSK were preceded four to five days prior by an unusually large amount of reactivated virus in the tears of that eye and whenever this unusually large amount of reactivated virus was detected in tears, rHSK always appeared 4–5 days later. In subsequent experiments using well defined heat stress the reactivation frequency was similarly increased, but no eyes developed rHSK. Conclusions The results reported here support the hypothesis that rHSK is associated not simply with elevated reactivation frequency, but rather with rare episodes of very high levels of reactivated virus in tears 4–5 days earlier. PMID:25859798

  1. Failure of d-psicose absorbed in the small intestine to metabolize into energy and its low large intestinal fermentability in humans.

    PubMed

    Iida, Tetsuo; Hayashi, Noriko; Yamada, Takako; Yoshikawa, Yuko; Miyazato, Shoko; Kishimoto, Yuka; Okuma, Kazuhiro; Tokuda, Masaaki; Izumori, Ken

    2010-02-01

    Experiments with rats have produced data on the metabolism and energy value of d-psicose; however, no such data have been obtained in humans. The authors assessed the availability of d-psicose absorbed in the small intestine by measuring carbohydrate energy expenditure (CEE) by indirect calorimetry. They measured the urinary excretion rate by quantifying d-psicose in urine for 48 hours. To examine d-psicose fermentation in the large intestine, the authors measured breath hydrogen gas and fermentability using 35 strains of intestinal bacteria. Six healthy subjects participated in the CEE test, and 14 participated in breath hydrogen gas and urine tests. d-Psicose fermentation subsequent to an 8-week adaptation period was also assessed by measuring hydrogen gas in 8 subjects. d-Psicose absorbed in the small intestine was not metabolized into energy, unlike glucose, because CEE did not increase within 3 hours of d-psicose ingestion (0.35 g/kg body weight [BW]). The accumulated d-psicose urinary excretion rates were around 70% for 0.34, 0.17, and 0.08 g/kg BW of ingested d-psicose. Low d-psicose fermentability was observed in intestinal bacteria and breath hydrogen gas tests, in which fructooligosaccharide (0.34, 0.17, and 0.08 g/kg BW) was used as a positive control because its available energy is known to be 8.4 kJ/g. Based on the results of the plot of breath hydrogen concentration vs calories ingested, the energy value of d-psicose was expected to be less than 1.6 kJ/g. Incremental d-psicose fermentability subsequent to an adaptation period was not observed.

  2. Large-area surveys for black carbon and other light-absorbing impurities in snow: Arctic, Antarctic, North America, China (Invited)

    NASA Astrophysics Data System (ADS)

    Warren, S. G.; Doherty, S. J.; Hegg, D.; Dang, C.; Zhang, R.; Grenfell, T. C.; Brandt, R. E.; Clarke, A. D.; Zatko, M.

    2013-12-01

    Absorption of radiation by ice is extremely weak at visible and near-UV wavelengths, so small amounts of light-absorbing impurities (LAI) in snow can dominate the absorption of sunlight at these wavelengths, reducing the albedo relative to that of pure snow and leading to earlier snowmelt. Snow samples were collected in Alaska, Canada, Greenland, Svalbard, Norway, Russia, and the Arctic Ocean, on tundra, glaciers, ice caps, sea ice, and frozen lakes, and in boreal forests. Snow was collected mostly in spring, when the entire winter snowpack was accessible for sampling. Snow was also collected at 67 sites in western North America. Expeditions from Lanzhou University obtained black carbon (BC) amounts at 84 sites in northeast and northwest China. BC was measured at 3 locations on the Antarctic Plateau, and at 5 sites on East Antarctic sea ice. The snow is melted and filtered; the filters are analyzed in a spectrophotometer. Median BC mixing ratios in snow range over 4 orders of magnitude from 0.2 ng/g in Antarctica to 1000 ng/g in northeast China. Chemical analyses, input to a receptor model, indicate that the major source of BC in most of the Arctic is biomass burning, but industrial sources dominate in Svalbard and the central Arctic Ocean. Non-BC impurities, principally brown (organic) carbon, are typically responsible for ~40% of the visible and ultraviolet absorption. In northeast China BC is the dominant LAI, but in Inner Mongolia soil dominates. When the snow surface layer melts, much of the BC is left at the top of the snowpack rather than carried away in meltwater, thus causing a positive feedback on snowmelt. This process was quantified through field studies in Greenland, Alaska, and Norway, where we found that only 10-30% of the BC is removed with meltwater. The BC content of the Arctic atmosphere has declined markedly since 1989, according to the continuous measurements of near-surface air in Canada, Alaska, and Svalbard. Correspondingly, our recent BC

  3. High-quality and Large-size Topological Insulator Bi2Te3-Gold Saturable Absorber Mirror for Mode-Locking Fiber Laser

    PubMed Central

    Chen, Hou-Ren; Tsai, Chih-Ya; Cheng, Hsin-Ming; Lin, Kuei-Huei; Yen, Po-Hsiu; Chen, Chyong-Hua; Hsieh, Wen-Feng

    2016-01-01

    A novel high-quality, large-size, reflection-type topological insulator Bi2Te3-Gold (BG) film-based nonlinear optical modulator has been successfully fabricated as a two-dimensional saturable absorber mirror (SAM) by pulsed laser deposition (PLD). This BG-SAM possesses saturation fluence of 108.3 μJ/cm2, modulation depth (ΔR) of 6.5%, non-saturable loss of 38.4%, high damage threshold above 1.354 mJ/cm2 and excellent uniformity providing for the generation of passive mode-locked (ML) pulses for erbium-doped fiber lasers (EDFLs) on a large sample area. Under 124 mW 976 nm pumping, We obtained 452-fs continuous-wave ML pulses with pulse energy of 91 pJ and full width at half-maximum (FWHM) of 6.72-nm from this EDFL. The results clearly evidence that the PLD is an efficient method for fabricating BG-SAM that is suitable for a compact ultrafast ML fiber laser system. PMID:27917938

  4. Large area growth of monolayer MoS2 film on quartz and its use as a saturable absorber in laser mode-locking

    NASA Astrophysics Data System (ADS)

    Zhao, Wei-fang; Yu, Hua; Liao, Meng-zhou; Zhang, Ling; Zou, Shu-zhen; Yu, Hai-juan; He, Chao-jian; Zhang, Jing-yuan; Zhang, Guang-yu; Lin, Xue-chun

    2017-02-01

    Monolayer MoS2 film on quartz was fabricated by a home-made three-temperature zone chemical vapor deposition method. The photo, AFM image, Raman spectroscopy and HRTEM image showed that high quality as-grown MoS2 film completely covered the whole quartz substrate of a few cm2. A Nd:YVO4 laser with mode-locking operation was obtained by using the monolayer MoS2 on quartz as the saturable absorber (SA). To the best of our knowledge, this is the first report on large-area growth of high quality monolayer MoS2 film on transparent quartz substrate, and the first time that the CVD MoS2 SA was used in mode-locked solid state lasers. Because of the large area, high transmission, low non-saturable loss and high optical damage threshold of this material, it is very suitable for application in mode-locked solid state lasers.

  5. Influence of a large amount of Co substitution on the magnetic properties of NdFeCoGaB magnets (abstract)

    NASA Astrophysics Data System (ADS)

    Tsutai, A.; Sakai, I.; Sahashi, M.; Inomata, K.

    1990-05-01

    We have found that a NdFeCoGaB sintered magnet containing 30 at. % Co still shows high coercive force in spite of such a large amount of Co substitution. The Curie temperature of the magnet is higher than that of the ternary NdFeB magnet by 280 °C. As a result, the following magnetic properties have been attained for Nd14.5Fe46Co30Ga1B8.5: Tc=590 °C, Br =11.7 kG, Hci =14.3 kOe, and (BH)max=32 MG Oe. Furthermore, in this magnet there exists an additional phase, Nd1(FeCoGa)4B1 with Ce1Co4B1 structure, which, as far as authors know, has not been reported to exist in the NdFeB-based magnets. In this study we investigated the magnetic properties and microstructure of Nd14.5Fe76-xCoxGa1B8.5 (x=16-50) sintered magnets. The high coercive force can be obtained in the Co-content region from 16 to 30 at. %. In particular, the magnet with 30 at. % Co shows coercive force as high as 14.3 kOe. However, further substitution of Co drastically deteriorates the magnetic properties. The coercive force of the magnet with 50 at. % Co is less than 1 kOe. From the metallographical point of view, the above-mentioned Nd1(FeCoGa)4B1 phase is not observed in the magnets containing less than 30 at. % Co. This phase abruptly appears in the magnet with 30 at. % Co and its amount increases with increasing Co content. The strongest x-ray-diffraction peak observed in the magnet with 50 at. % Co comes from the Nd1(FeCoGa)4B1 phase. The demagnetization-curve measurements suggest that reverse magnetic domains are nucleated in the Nd1(FeCoGa)4B1 phase at a low reverse magnetic field. It is noteworthy that the magnet with 30 at. % Co maintains the high coercive force in spite of the existence of such a soft magnetic phase. Details will be discussed in the coming session.

  6. Effects of single-session dietary counseling by dieticians on salt reduction in cardiology outpatients who consumed large amounts of salt.

    PubMed

    Yamasaki, Tamami; Sadanaga, Tsuneaki; Hirota, Shinichi

    2015-07-01

    The purpose of the present study was to assess the effects of single-session dietary counseling on salt restriction in Japanese cardiology outpatients as assessed using spot urine measurements. A total of 72 patients (73±11 years old, including 30 females) who visited a cardiology outpatient clinic and had a salt intake of >8 g/day were included in this study. The patients received dietary counseling for salt restriction by expert dieticians at the time of enrollment. The daily dietary salt intake was estimated using the spot urine test at baseline prior to dietary counseling, at 3-9 weeks (next office visit), and at 24-52 weeks during follow-up evaluations. The baseline level of estimated salt excretion was 11.3±1.5 g/day, which was reduced to 9.6±2.3 g/day (P<0.01) at 3-9 weeks, but increased again at 24-52 weeks to 10.4±2.1 g/day, which was less than the baseline value (P=0.034 vs. 3-9 weeks; P=0.025 vs. baseline). The numbers of patients who achieved salt excretion levels of <6.0 and <8.0 g/day at 3-9 weeks were 4 (5.6%) and 19 (26%) patients, respectively, and were further reduced to no patients (0%; P=0.043 vs. 3-9 weeks) and 9 (13%; P=0.035 vs. 3-9 weeks) patients at 24-52 weeks of follow-up evaluation, respectively. In conclusion, the efficacy of dietary counseling by expert dieticians in restricting the salt intake of patients who consumed large amounts of salt was modest and temporary. Multiple nutritional- and behavioral-oriented approaches should be considered to achieve further reductions in salt intake.

  7. Effects of single-session dietary counseling by dieticians on salt reduction in cardiology outpatients who consumed large amounts of salt

    PubMed Central

    YAMASAKI, TAMAMI; SADANAGA, TSUNEAKI; HIROTA, SHINICHI

    2015-01-01

    The purpose of the present study was to assess the effects of single-session dietary counseling on salt restriction in Japanese cardiology outpatients as assessed using spot urine measurements. A total of 72 patients (73±11 years old, including 30 females) who visited a cardiology outpatient clinic and had a salt intake of >8 g/day were included in this study. The patients received dietary counseling for salt restriction by expert dieticians at the time of enrollment. The daily dietary salt intake was estimated using the spot urine test at baseline prior to dietary counseling, at 3–9 weeks (next office visit), and at 24–52 weeks during follow-up evaluations. The baseline level of estimated salt excretion was 11.3±1.5 g/day, which was reduced to 9.6±2.3 g/day (P<0.01) at 3–9 weeks, but increased again at 24–52 weeks to 10.4±2.1 g/day, which was less than the baseline value (P=0.034 vs. 3–9 weeks; P=0.025 vs. baseline). The numbers of patients who achieved salt excretion levels of <6.0 and <8.0 g/day at 3–9 weeks were 4 (5.6%) and 19 (26%) patients, respectively, and were further reduced to no patients (0%; P=0.043 vs. 3–9 weeks) and 9 (13%; P=0.035 vs. 3–9 weeks) patients at 24–52 weeks of follow-up evaluation, respectively. In conclusion, the efficacy of dietary counseling by expert dieticians in restricting the salt intake of patients who consumed large amounts of salt was modest and temporary. Multiple nutritional- and behavioral-oriented approaches should be considered to achieve further reductions in salt intake. PMID:26170920

  8. Oil and fat absorbing polymers

    NASA Technical Reports Server (NTRS)

    Marsh, H. E., Jr. (Inventor)

    1977-01-01

    A method is described for forming a solid network polymer having a minimal amount of crosslinking for use in absorbing fats and oils. The polymer remains solid at a swelling ratio in oil or fat of at least ten and provides an oil absorption greater than 900 weight percent.

  9. Method for quantitative determination and separation of trace amounts of chemical elements in the presence of large quantities of other elements having the same atomic mass

    DOEpatents

    Miller, C.M.; Nogar, N.S.

    1982-09-02

    Photoionization via autoionizing atomic levels combined with conventional mass spectroscopy provides a technique for quantitative analysis of trace quantities of chemical elements in the presence of much larger amounts of other elements with substantially the same atomic mass. Ytterbium samples smaller than 10 ng have been detected using an ArF* excimer laser which provides the atomic ions for a time-of-flight mass spectrometer. Elemental selectivity of greater than 5:1 with respect to lutetium impurity has been obtained. Autoionization via a single photon process permits greater photon utilization efficiency because of its greater absorption cross section than bound-free transitions, while maintaining sufficient spectroscopic structure to allow significant photoionization selectivity between different atomic species. Separation of atomic species from others of substantially the same atomic mass is also described.

  10. A neutron-absorbing porcelain enamel for coating nuclear equipment

    SciTech Connect

    Iverson, D.C.

    1988-01-01

    In 1985, nuclear safety analyses showed that under upset conditions, strict administrative controls were necessary to limit access to a new processing vessel for enriched uranium service at the Savannah River Plant (SRP). In order to increase the level of nuclear safety associated with that vessel, the traditional methods of incorporating neutron absorbers (borated stainless steel, boral, cadmium foil, etc.) were reviewed, however, process conditions did not permit their use. A neutron-absorbing porcelain enamel containing large amounts of cadmium and boron was developed as a safe, cost-effective alternative to traditional neutron-absorbing methods. Several pieces of coated process equipment have been installed or are planned for installation at SRP.

  11. Three intervening galaxy absorbers towards GRB 060418: faint and dusty?

    NASA Astrophysics Data System (ADS)

    Ellison, Sara L.; Vreeswijk, Paul; Ledoux, Cédric; Willis, Jon P.; Jaunsen, Andreas; Wijers, Ralph A. M. J.; Smette, Alain; Fynbo, Johan P. U.; Møller, Palle; Hjorth, Jens; Kaufer, Andreas

    2006-10-01

    We present an analysis of three strong, intervening Mg II absorption systems (zabs = 0.603, 0.656, 1.107) towards the optical afterglow of gamma-ray burst (GRB) 060418. From high-resolution Ultraviolet and Visual Echelle Spectrograph (UVES) spectra we measure metal column densities and find that the highest redshift absorber exhibits a large amount of dust depletion compared with damped Lyman absorbers (DLAs) seen in quasi-stellar object (QSO) spectra. The intervening zabs = 1.107 absorber is also unusual in exhibiting a clear 2175-Å bump, the first time this feature has been definitively detected in a GRB spectrum. The GRB afterglow spectrum is best fitted with a two-component extinction curve: a Small Magellanic Cloud (SMC) extinction law at z = 1.49 (the redshift of the host) with E(B - V) = 0.07 +/- 0.01 and a Galactic extinction curve at z ~ 1.1 with E(B - V) = 0.08 +/- 0.01. We also present a moderately deep New Technology Telescope (NTT) R-band image of the GRB 060418 field and spectroscopy of four galaxies within 1 arcmin. None of these objects has a redshift that matches any of the intervening absorbers, and we conclude that the galaxies responsible for the two intervening MgII absorbers at z ~ 0.6 have luminosities .

  12. Mushroom plasmonic metamaterial infrared absorbers

    SciTech Connect

    Ogawa, Shinpei Fujisawa, Daisuke; Hata, Hisatoshi; Uetsuki, Mitsuharu; Misaki, Koji; Kimata, Masafumi

    2015-01-26

    There has been a considerable amount of interest in the development of various types of electromagnetic wave absorbers for use in different wavelength ranges. In particular, infrared (IR) absorbers with wavelength selectivity can be applied to advanced uncooled IR sensors, which would be capable of identifying objects through their radiation spectrum. In the present study, mushroom plasmonic metamaterial absorbers (MPMAs) for the IR wavelength region were designed and fabricated. The MPMAs consist of a periodic array of thin metal micropatches connected to a thin metal plate with narrow silicon (Si) posts. A Si post height of 200 nm was achieved by isotropic XeF{sub 2} etching of a thin Si layer sandwiched between metal plates. This fabrication procedure is relatively simple and is consistent with complementary metal oxide semiconductor technology. The absorption spectra of the fabricated MPMAs were experimentally measured. In addition, theoretical calculations of their absorption properties were conducted using rigorous coupled wave analysis. Both the calculated and measured absorbance results demonstrated that these MPMAs can realize strong selective absorption at wavelengths beyond the period of the array by varying the micropatch width. Absorbance values greater than 90% were achieved. Dual- or single-mode absorption can also be selected by varying the width of the Si posts. Pixel structures using such MPMAs could be used as high responsivity, high resolution and fast uncooled IR sensors.

  13. Mushroom plasmonic metamaterial infrared absorbers

    NASA Astrophysics Data System (ADS)

    Ogawa, Shinpei; Fujisawa, Daisuke; Hata, Hisatoshi; Uetsuki, Mitsuharu; Misaki, Koji; Kimata, Masafumi

    2015-01-01

    There has been a considerable amount of interest in the development of various types of electromagnetic wave absorbers for use in different wavelength ranges. In particular, infrared (IR) absorbers with wavelength selectivity can be applied to advanced uncooled IR sensors, which would be capable of identifying objects through their radiation spectrum. In the present study, mushroom plasmonic metamaterial absorbers (MPMAs) for the IR wavelength region were designed and fabricated. The MPMAs consist of a periodic array of thin metal micropatches connected to a thin metal plate with narrow silicon (Si) posts. A Si post height of 200 nm was achieved by isotropic XeF2 etching of a thin Si layer sandwiched between metal plates. This fabrication procedure is relatively simple and is consistent with complementary metal oxide semiconductor technology. The absorption spectra of the fabricated MPMAs were experimentally measured. In addition, theoretical calculations of their absorption properties were conducted using rigorous coupled wave analysis. Both the calculated and measured absorbance results demonstrated that these MPMAs can realize strong selective absorption at wavelengths beyond the period of the array by varying the micropatch width. Absorbance values greater than 90% were achieved. Dual- or single-mode absorption can also be selected by varying the width of the Si posts. Pixel structures using such MPMAs could be used as high responsivity, high resolution and fast uncooled IR sensors.

  14. Electromagnetic scattering by pyramidal and wedge absorber

    NASA Technical Reports Server (NTRS)

    Dewitt, Brian T.; Burnside, Walter D.

    1988-01-01

    Electromagnetic scattering from pyramidal and wedge absorbers used to line the walls of modern anechoic chambers is measured and compared with theoretically predicted values. The theoretical performance for various angles of incidence is studied. It is shown that a pyramidal absorber scatters electromagnetic energy more as a random rough surface does. The apparent reflection coefficient from an absorber wall illuminated by a plane wave can be much less than the normal absorber specifications quoted by the manufacturer. For angles near grazing incidence, pyramidal absorbers give a large backscattered field from the pyramid side-faces or edges. The wedge absorber was found to give small backscattered fields for near-grazing incidence. Based on this study, some new guidelines for the design of anechoic chambers are advocated because the specular scattering models used at present do not appear valid for pyramids that are large compared to the wavelength.

  15. Helicopter rotor lag damping augmentation based on a radial absorber and Coriolis coupling

    NASA Astrophysics Data System (ADS)

    Byers, Lynn Karen

    A radial vibration absorber is proposed to augment rotor lag damping. Modeled as a discrete mass restrained by a damped spring and moving along the spanwise direction within the rotor blade, it introduces damping into the lag mode of the blade through strong Coriolis coupling. A two-degree-of-freedom model is developed and used to examine the effectiveness of the radial absorber in transferring damping to the rotor lag mode. Results demonstrate that it is possible to introduce a significant amount of damping in the lag mode with a relatively small absorber mass, and the corresponding amplitudes of 1/rev periodic motions are not excessively large. The lag mode damping and 1/rev motions are also compared with the results achieved for an embedded chordwise inertial damper. A classical six-degree-of-freedom aeromechanical stability analysis is augmented with two absorber cyclic degrees of freedom in the nonrotating frame to examine the effect of the radial absorber on aeromechanical stability characteristics. These results indicate that ground resonance instability is eliminated for the range of absorber parameters considered, and in most cases, the stability margins are significant. A rotor blade with a discrete radial vibration absorber is also analyzed to examine the effect of the absorber on rotor blade and hub loads. The rotor blade is modeled as an elastic beam undergoing flap and lag bending, with the absorber modeled as a discrete mass restrained by a damped spring, moving in the spanwise direction within the rotor blade. Results indicate that the addition of the absorber does not detrimentally affect the blade spanwise and root loads, as well as steady and vibratory hub loads. Finally, device concepts and implementation possibilities are considered for the embedded radial vibration absorber.

  16. Externally tuned vibration absorber

    DOEpatents

    Vincent, Ronald J.

    1987-09-22

    A vibration absorber unit or units are mounted on the exterior housing of a hydraulic drive system of the type that is powered from a pressure wave generated, e.g., by a Stirling engine. The hydraulic drive system employs a piston which is hydraulically driven to oscillate in a direction perpendicular to the axis of the hydraulic drive system. The vibration absorbers each include a spring or other resilient member having one side affixed to the housing and another side to which an absorber mass is affixed. In a preferred embodiment, a pair of vibration absorbers is employed, each absorber being formed of a pair of leaf spring assemblies, between which the absorber mass is suspended.

  17. Shock absorber control system

    SciTech Connect

    Nakano, Y.; Ohira, M.; Ushida, M.; Miyagawa, T.; Shimodaira, T.

    1987-01-13

    A shock absorber control system is described for controlling a dampening force of a shock absorber of a vehicle comprising: setting means for setting a desired dampening force changeable within a predetermined range; drive means for driving the shock absorber to change the dampening force of the shock absorber linearly; control means for controlling the drive means in accordance with the desired dampening force when the setting of the desired dampening force has been changed; detecting means for detecting an actual dampening force of the shock absorber; and correcting means for correcting the dampening force of the shock absorber by controlling the drive means in accordance with a difference between the desired dampening force and the detected actual dampening force.

  18. CPCs with segmented absorbers

    SciTech Connect

    Keita, M.; Robertson, H.S. )

    1991-01-01

    One of the most promising means of improving the performance of solar thermal collectors is to reduce the energy lost by the hot absorber. One way to do this, not currently part of the technology, is to recognize that since the absorber is usually not irradiated uniformly, it is therefore possible to construct an absorber of thermally isolated segments, circulate the fluid in sequence from low to high irradiance segments, and reduce loss by improving effective concentration. This procedure works even for ideal concentrators, without violating Winston's theorem. Two equivalent CPC collectors with single and segmented absorber were constructed and compared under actual operating conditions. The results showed that the daily thermal efficiency of the collector with segmented absorber is higher (about 13%) than that of the collector with nonsegmented absorber.

  19. Methods for absorbing neutrons

    DOEpatents

    Guillen, Donna P [Idaho Falls, ID; Longhurst, Glen R [Idaho Falls, ID; Porter, Douglas L [Idaho Falls, ID; Parry, James R [Idaho Falls, ID

    2012-07-24

    A conduction cooled neutron absorber may include a metal matrix composite that comprises a metal having a thermal neutron cross-section of at least about 50 barns and a metal having a thermal conductivity of at least about 1 W/cmK. Apparatus for providing a neutron flux having a high fast-to-thermal neutron ratio may include a source of neutrons that produces fast neutrons and thermal neutrons. A neutron absorber positioned adjacent the neutron source absorbs at least some of the thermal neutrons so that a region adjacent the neutron absorber has a fast-to-thermal neutron ratio of at least about 15. A coolant in thermal contact with the neutron absorber removes heat from the neutron absorber.

  20. A hydraulic absorber for wideband vibration reduction in ship hulls

    SciTech Connect

    Hsueh, W.J.; Lee, Y.J. . Dept. of Naval Architecture and Ocean Engineering)

    1994-02-01

    A vibration reduction of ship hulls by an active absorber system is proposed. In the scheme, a tuned mass is moved according to the hull vibration as measured by a multi-mode sensing system in order to generate a suitable active force for vibration reduction of hull girder. In order to supply the large amount of required power, a hydraulic servo system is implemented. Then the dynamic characteristic of the hydraulic system is considered for system design. Based on stochastic theory and optimal theory, the control law of the system is derived in order to approach the optimal level of vibration reduction. A 10-t absorber is applied to a 87,000-t oil tanker to demonstrate the feasibility of this scheme. The results show that the multi-peak values of resonance are suppressed in frequency response. Moreover, the vibration excited by propeller and engine is reduced to an extremely efficient level by this scheme.

  1. Nonlinear dynamic vibration absorbers with a saturation

    NASA Astrophysics Data System (ADS)

    Febbo, M.; Machado, S. P.

    2013-03-01

    The behavior of a new type of nonlinear dynamic vibration absorber is studied. A distinctive characteristic of the proposed absorber is the impossibility to extend the system to infinity. The mathematical formulation is based on a finite extensibility nonlinear elastic potential to model the saturable nonlinearity. The absorber is attached to a single degree-of-freedom linear/nonlinear oscillator subjected to a periodic external excitation. In order to solve the equations of motion and to analyze the frequency-response curves, the method of averaging is used. The performance of the FENE absorber is evaluated considering a variation of the nonlinearity of the primary system, the damping and the linearized frequency of the absorber and the mass ratio. The numerical results show that the proposed absorber has a very good efficiency when the nonlinearity of the primary system increases. When compared with a cubic nonlinear absorber, for a large nonlinearity of the primary system, the FENE absorber shows a better effectiveness for the whole studied frequency range. A complete absence of quasi-periodic oscillations is also found for an appropriate selection of the parameters of the absorber. Finally, direct integrations of the equations of motion are performed to verify the accuracy of the proposed method.

  2. Advanced neutron absorber materials

    DOEpatents

    Branagan, Daniel J.; Smolik, Galen R.

    2000-01-01

    A neutron absorbing material and method utilizing rare earth elements such as gadolinium, europium and samarium to form metallic glasses and/or noble base nano/microcrystalline materials, the neutron absorbing material having a combination of superior neutron capture cross sections coupled with enhanced resistance to corrosion, oxidation and leaching.

  3. Multispectral metamaterial absorber.

    PubMed

    Grant, J; McCrindle, I J H; Li, C; Cumming, D R S

    2014-03-01

    We present the simulation, implementation, and measurement of a multispectral metamaterial absorber (MSMMA) and show that we can realize a simple absorber structure that operates in the mid-IR and terahertz (THz) bands. By embedding an IR metamaterial absorber layer into a standard THz metamaterial absorber stack, a narrowband resonance is induced at a wavelength of 4.3 μm. This resonance is in addition to the THz metamaterial absorption resonance at 109 μm (2.75 THz). We demonstrate the inherent scalability and versatility of our MSMMA by describing a second device whereby the MM-induced IR absorption peak frequency is tuned by varying the IR absorber geometry. Such a MSMMA could be coupled with a suitable sensor and formed into a focal plane array, enabling multispectral imaging.

  4. A rapid and practical strategy for the determination of platinum, palladium, ruthenium, rhodium, iridium and gold in large amounts of ultrabasic rock by inductively coupled plasma optical emission spectrometry combined with ultrasound extraction

    NASA Astrophysics Data System (ADS)

    Zhang, Gai; Tian, Min

    2015-04-01

    This proposed method regulated the determination of platinum, palladium, ruthenium, rhodium, iridium and gold in platinum-group ores by nickel sulfide fire assay—inductively coupled plasma optical emission spectrometry (ICP-OES) combined with ultrasound extraction for the first time. The quantitative limits were 0.013-0.023μg/g. The samples were fused to separate the platinum-group elements from matrix. The nickel sulfide button was then dissolved with hydrochloric acid and the insoluble platinum-group sulfide residue was dissolved with aqua regia by ultrasound bath and finally determined by ICP-OES. The proposed method has been applied into the determination of platinum-group element and gold in large amounts of ultrabasic rocks from the Great Dyke of Zimbabwe.

  5. Internal absorber solar collector

    DOEpatents

    Sletten, Carlyle J.; Herskovitz, Sheldon B.; Holt, F. S.; Sletten, E. J.

    1981-01-01

    Thin solar collecting panels are described made from arrays of small rod collectors consisting of a refracting dielectric rod lens with an absorber imbedded within it and a reflecting mirror coated on the back side of the dielectric rod. Non-tracking collector panels on vertical walls or roof tops receive approximately 90% of solar radiation within an acceptance zone 60.degree. in elevation angle by 120.degree. or more in the azimuth sectors with a collector concentration ratio of approximately 3.0. Miniaturized construction of the circular dielectric rods with internal absorbers reduces the weight per area of glass, plastic and metal used in the collector panels. No external parts or insulation are needed as heat losses are low due to partial vacuum or low conductivity gas surrounding heated portions of the collector. The miniature internal absorbers are generally made of solid copper with black selective surface and the collected solar heat is extracted at the collector ends by thermal conductivity along the absorber rods. Heat is removed from end fittings by use of liquid circulants. Several alternate constructions are provided for simplifying collector panel fabrication and for preventing the thermal expansion and contraction of the heated absorber or circulant tubes from damaging vacuum seals. In a modified version of the internal absorber collector, oil with temperature dependent viscosity is pumped through a segmented absorber which is now composed of closely spaced insulated metal tubes. In this way the circulant is automatically diverted through heated portions of the absorber giving higher collector concentration ratios than theoretically possible for an unsegmented absorber.

  6. Electromagnetic power absorber

    NASA Technical Reports Server (NTRS)

    Iwasaki, R. S. (Inventor)

    1979-01-01

    A structure is presented with a surface portion of dielectric material which passes electromagnetic radiation and with a portion below the surface which includes material that absorbs the radiation, the face of the structure being formed with numerous steep ridges. The steepness of the dielectric material results in a high proportion of the electromagnetic energy passing through the surface for absorption by the absorbing material under the surface. A backing of aluminum or other highly heat-conductive and reflective material lies under the face and has very steep protuberances supporting the absorbing and dielectric materials.

  7. Methods of calculating radiation absorbed dose.

    PubMed

    Wegst, A V

    1987-01-01

    The new tumoricidal radioactive agents being developed will require a careful estimate of radiation absorbed tumor and critical organ dose for each patient. Clinical methods will need to be developed using standard imaging or counting instruments to determine cumulated organ activities with tracer amounts before the therapeutic administration of the material. Standard MIRD dosimetry methods can then be applied.

  8. OVI absorbers in SDSS spectra

    NASA Astrophysics Data System (ADS)

    Frank, Stephan

    with the ubiquitous Lya forest lines, and estimate the success rate of retrieving each individual candidate as a function of its redshift, the emission redshift of the quasar, the strength of the absorber and the measured S/N of the spectrum by modelling typical Ly forest spectra. These correction factors allow us to derive the 'incompleteness and S/N corrected' redshift number densities of O VI absorbers. We can place a secure lower limit for the contribution of O VI to the closure mass density at the redshifts probed here: O OV I (2.8 < z < 3.2) >= 1.9 × 10 - 8 h -1 . We show that the strong lines we probe account for over 65% of the mass in the O VI absorbers; the weak absorbers, while dominant in line number density, do not contribute significantly to the mass density. Making a conservative assumption about the ionisation fraction, [Special characters omitted.] , and adopting the Anders & Grevesse (1989) solar abundance values, we derive the mean metallicty of the gas probed in our search : z(2.8 < z < 3.2) >= 3.6 × 10 -4 h , in good agreement with other studies. These results demonstrate that large spectroscopic datasets such as SDSS can play an important role in QSO absorption line studies, in spite of the relatively low resolution. Lastly, we have performed a stacking analysis whereby we shift individual spectra back to the rest-frame of the absorber candidate, and derive a mean absorption spectrum for various subsamples. Besides further validating the reality of the absorbers themselves, i.e. ruling out spurious interlopers and other misclassifications, we can use these stacked spectra for a variety of purposes. First of all, we can judge the effects of additional cut criteria like a minimal strength for associated CIV absorption, and hence produce cleaner and better defined subsamples, increasing the strength of future proposals for high-resolution studies. Secondly, the stack itself contains valuable information about the gas probed in our search. We have

  9. Water absorbency by wool fibers: Hofmeister effect.

    PubMed

    Lo Nostro, Pierandrea; Fratoni, Laura; Ninham, Barry W; Baglioni, Piero

    2002-01-01

    Wool is a complex material, composed of cuticle and epicuticle cells, surrounded by a cell membrane complex. Wool fibers absorb moisture from air, and, once immersed in water, they take up considerable amounts of liquid. The water absorbency parameter can be determined from weight gain, according to a standard method, and used to quantify this phenomenon. In this paper we report a study on the water absorbency (or retention) of untreated wool fibers in the presence of aqueous 1 M salt solutions at 29 degrees C and a relative humidity of either 33% or 56%. The effect of anions was determined by selecting a wide range of different sodium salts, while the effect of cations was checked through some chlorides and nitrates. Our results show a significant specific ion and ion pair "Hofmeister" effects, that change the amount of water absorbed by the fibers. To understand this phenomenon, the water absorbency parameter (A(w)) is compared to different physicochemical parameters such as the lyotropic number, free energy of hydration of ions, molar surface tension increment, polarizability, refractive index increment, and molar refractivity. The data indicate that this Hofmeister phenomenon is controlled by dispersion forces that depend on the polarizability of ionic species, their adsorption frequencies, the solvent, and the substrate. These dispersion forces dominate the behavior in concentrated solutions. They are in accord with new developing theories of solutions and molecular interactions in colloidal systems that account for Hofmeister effects.

  10. Carbon dioxide absorber and regeneration assemblies useful for power plant flue gas

    DOEpatents

    Vimalchand, Pannalal; Liu, Guohai; Peng, Wan Wang

    2012-11-06

    Disclosed are apparatus and method to treat large amounts of flue gas from a pulverized coal combustion power plant. The flue gas is contacted with solid sorbents to selectively absorb CO.sub.2, which is then released as a nearly pure CO.sub.2 gas stream upon regeneration at higher temperature. The method is capable of handling the necessary sorbent circulation rates of tens of millions of lbs/hr to separate CO.sub.2 from a power plant's flue gas stream. Because pressurizing large amounts of flue gas is cost prohibitive, the method of this invention minimizes the overall pressure drop in the absorption section to less than 25 inches of water column. The internal circulation of sorbent within the absorber assembly in the proposed method not only minimizes temperature increases in the absorber to less than 25.degree. F., but also increases the CO.sub.2 concentration in the sorbent to near saturation levels. Saturating the sorbent with CO.sub.2 in the absorber section minimizes the heat energy needed for sorbent regeneration. The commercial embodiments of the proposed method can be optimized for sorbents with slower or faster absorption kinetics, low or high heat release rates, low or high saturation capacities and slower or faster regeneration kinetics.

  11. Energy-Absorbing, Lightweight Wheels

    NASA Technical Reports Server (NTRS)

    Waydo, Peter

    2003-01-01

    Improved energy-absorbing wheels are under development for use on special-purpose vehicles that must traverse rough terrain under conditions (e.g., extreme cold) in which rubber pneumatic tires would fail. The designs of these wheels differ from those of prior non-pneumatic energy-absorbing wheels in ways that result in lighter weights and more effective reduction of stresses generated by ground/wheel contact forces. These wheels could be made of metals and/or composite materials to withstand the expected extreme operating conditions. As shown in the figure, a wheel according to this concept would include an isogrid tire connected to a hub via spring rods. The isogrid tire would be a stiff, lightweight structure typically made of aluminum. The isogrid aspect of the structure would both impart stiffness and act as a traction surface. The hub would be a thin-walled body of revolution having a simple or compound conical or other shape chosen for structural efficiency. The spring rods would absorb energy and partially isolate the hub and the supported vehicle from impact loads. The general spring-rod configuration shown in the figure was chosen because it would distribute contact and impact loads nearly evenly around the periphery of the hub, thereby helping to protect the hub against damage that would otherwise be caused by large loads concentrated onto small portions of the hub.

  12. 21 CFR 880.5300 - Medical absorbent fiber.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... and that is used for applying medication to, or absorbing small amounts of body fluids from, a patient's body surface. Absorbent fibers intended solely for cosmetic purposes are not included in...

  13. 21 CFR 880.5300 - Medical absorbent fiber.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... and that is used for applying medication to, or absorbing small amounts of body fluids from, a patient's body surface. Absorbent fibers intended solely for cosmetic purposes are not included in...

  14. Unidirectional perfect absorber

    PubMed Central

    Jin, L.; Wang, P.; Song, Z.

    2016-01-01

    This study proposes a unidirectional perfect absorber (UPA), which we realized with a two-arm Aharonov-Bohm interferometer, that consists of a dissipative resonator side-coupled to a uniform resonator array. The UPA has reflection-less full absorption on one direction, and reflectionless full transmission on the other, with an appropriate magnetic flux and coupling, detuning, and loss of the side-coupled resonator. The magnetic flux controls the transmission, the left transmission is larger for magnetic flux less than one-half flux quantum; and the right transmission is larger for magnetic flux between one-half and one flux quantum. Besides, a perfect absorber (PA) can be realized based on the UPA, in which light waves from both sides, with arbitrary superposition of the ampli- tude and phase, are perfectly absorbed. The UPA is expected to be useful in the design of novel optical devices. PMID:27615125

  15. Shock absorber servicing tool

    NASA Technical Reports Server (NTRS)

    Koepler, Jack L. (Inventor); Hill, Robert L. (Inventor)

    1981-01-01

    A tool to assist in the servicing of a shock absorber wherein the shock absorber is constructed of a pair of aligned gas and liquid filled chambers. Each of the chambers is separated by a movable separator member. Maximum efficiency of the shock absorber is achieved in the locating of a precise volume of gas within the gas chamber and a precise volume of liquid within the liquid chamber. The servicing tool of this invention employs a rod which is to connect with the separator and by observation of the position of the rod with respect to the gauge body, the location of the separator is ascertained even though it is not directly observable.

  16. Unidirectional perfect absorber

    NASA Astrophysics Data System (ADS)

    Jin, L.; Wang, P.; Song, Z.

    2016-09-01

    This study proposes a unidirectional perfect absorber (UPA), which we realized with a two-arm Aharonov-Bohm interferometer, that consists of a dissipative resonator side-coupled to a uniform resonator array. The UPA has reflection-less full absorption on one direction, and reflectionless full transmission on the other, with an appropriate magnetic flux and coupling, detuning, and loss of the side-coupled resonator. The magnetic flux controls the transmission, the left transmission is larger for magnetic flux less than one-half flux quantum; and the right transmission is larger for magnetic flux between one-half and one flux quantum. Besides, a perfect absorber (PA) can be realized based on the UPA, in which light waves from both sides, with arbitrary superposition of the ampli- tude and phase, are perfectly absorbed. The UPA is expected to be useful in the design of novel optical devices.

  17. Thin film absorber for a solar collector

    DOEpatents

    Wilhelm, William G.

    1985-01-01

    This invention pertains to energy absorbers for solar collectors, and more particularly to high performance thin film absorbers. The solar collectors comprising the absorber of this invention overcome several problems seen in current systems, such as excessive hardware, high cost and unreliability. In the preferred form, the apparatus features a substantially rigid planar frame with a thin film window bonded to one planar side of the frame. An absorber in accordance with the present invention is comprised of two thin film layers that are sealed perimetrically. In a preferred embodiment, thin film layers are formed from a metal/plastic laminate. The layers define a fluid-tight planar envelope of large surface area to volume through which a heat transfer fluid flows. The absorber is bonded to the other planar side of the frame. The thin film construction of the absorber assures substantially full envelope wetting and thus good efficiency. The window and absorber films stress the frame adding to the overall strength of the collector.

  18. Shock Absorbing System

    NASA Astrophysics Data System (ADS)

    1982-01-01

    A lightweight, inexpensive shock-absorbing system, developed by Langley Research Center 20 years ago, is now in service as safety device for an automated railway at Duke University Medical Center. The transportation system travels at about 25 miles per hour, carrying patients, visitors, staff and cargo. At the end of each guideway of the system are "frangible," (breakable) tube "buffers." If a slowing car fails to make a complete stop at the terminal, it would bump and shatter the tubes, absorbing energy that might otherwise jolt the passengers or damage the vehicle.

  19. Higher toxicity of dibutyltin and poly-L-lactide with a large amount of tin but lower toxicity of poly-L-lactide of synthetic artificial dura mater exhibited on murine astrocyte cell line.

    PubMed

    Tsuji, Masayoshi; Inoue, Yoko; Sugaya, Chiemi; Tsunoda, Masashi; Sugaya, Tsukiko; Takahashi, Masami; Yuba, Toshiyasu; Tsuchiya, Toshie; Aizawa, Yoshiharu

    2010-06-01

    Neurotoxicities of dibutyltin (DBT), tin(II) octylate (OT), poly-L-lactides (PLLA, molecular weight [MW]=5000, PLLA 5000), PLLA without tin (MW=3000, PLLA 3000), PLLA with a large amount (590 ppm) of tin (S3), poly(glycolic acid-co-epsilon-caprolactone) oligomer (MW=6200, PGC oligomer), and poly(L-lactic acid-co-glycolic acid-co-epsilon-caprolactone) oligomer (MW=6400, PLGC oligomer) related to artificial dura mater were examined using the murine astrocyte cell line, CRL-2534. The indices were cell viability, glutamate concentration in the cell supernatant, and cell proliferation. Lower cell viability was observed among cells exposed to 0.5 microM DBT or 10 microg/ml of S3. There were no differences in cell viability of astrocytes exposed to OT, PLLA 5000, PLLA 3000, PGC oligomer, or PLGC oligomer. Mean glutamate concentration in the supernatant of cells exposed to 0.25 muM DBT was higher than that of the control after 2 h incubation. Lower mean concentration of glutamate in the supernatant of cells exposed to 5 microg/ml of S3 was observed after 2 h incubation. Cells exposed to 50 microg/ml of PGC oligomer had a higher mean concentration of glutamate in the supernatant. OT only inhibited cell proliferation at 100 microM. Proliferation of cells exposed to 0.25 microM or 0.5 microM DBT was inhibited, as was that of cells exposed to 100 microM OT, 50 microg/ml PLLA 5000, 50 microg/ml PLLA 3000, and 5 microg/ml S3, 5 d and 7 d after exposure. Although DBT does not reach levels that induced neurotoxicity in artificial dura mater, these results suggest that DBT is neurotoxic and PLLA toxicity increases with the increase in tin concentration.

  20. Durability of Polymeric Glazing and Absorber Materials

    SciTech Connect

    Jorgensen, G.; Terwilliger, K.; Bingham, C.; Milbourne, M.

    2005-01-01

    The Solar Heating and Lighting Program has set the goal of reducing the cost of solar water heating systems by at least 50%. An attractive approach to such large cost reduction is to replace glass and metal parts with less-expensive, lighter-weight, more-integrated polymeric components. The key challenge with polymers is to maintain performance and assure requisite durability for extended lifetimes. The objective of this task is to quantify lifetimes through measurement of the optical and mechanical stability of candidate polymeric glazing and absorber materials. Polycarbonate sheet glazings, as proposed by two industry partners, have been tested for resistance to UV radiation with three complementary methods. Incorporation of a specific 2-mil thick UV-absorbing screening layer results in glazing lifetimes of at least 15 years; improved screens promise even longer lifetimes. Proposed absorber materials were tested for creep and embrittlement under high temperature, and appear adequate for planned ICS absorbers.

  1. Solar concentrator/absorber

    NASA Technical Reports Server (NTRS)

    Von Tiesenhausen, G. F.

    1976-01-01

    Collector/energy converter, consisting of dual-slope optical concentrator and counterflow thermal energy absorber, is attached to multiaxis support structure. Efficient over wide range of illumination levels, device may be used to generate high temperature steam, serve as solar powered dryer, or power absorption cycle cooler.

  2. Neutron Absorbing Alloys

    SciTech Connect

    Mizia, Ronald E.; Shaber, Eric L.; DuPont, John N.; Robino, Charles V.; Williams, David B.

    2004-05-04

    The present invention is drawn to new classes of advanced neutron absorbing structural materials for use in spent nuclear fuel applications requiring structural strength, weldability, and long term corrosion resistance. Particularly, an austenitic stainless steel alloy containing gadolinium and less than 5% of a ferrite content is disclosed. Additionally, a nickel-based alloy containing gadolinium and greater than 50% nickel is also disclosed.

  3. Shock Absorbing Helmets

    NASA Technical Reports Server (NTRS)

    1978-01-01

    This paper presents a description of helmets used by football players that offer three times the shock-absorbing capacity of earlier types. An interior padding for the helmets, composed of Temper Foam, first used by NASA's Ames Research Center in the design of aircraft seats is described.

  4. Metasurface Broadband Solar Absorber

    PubMed Central

    Azad, Abul K.; Kort-Kamp, Wilton J. M.; Sykora, Milan; Weisse-Bernstein, Nina R.; Luk, Ting S.; Taylor, Antoinette J.; Dalvit, Diego A. R.; Chen, Hou-Tong

    2016-01-01

    We demonstrate a broadband, polarization independent, wide-angle absorber based on a metallic metasurface architecture, which accomplishes greater than 90% absorptance in the visible and near-infrared range of the solar spectrum, and exhibits low absorptivity (emissivity) at mid- and far-infrared wavelengths. The complex unit cell of the metasurface solar absorber consists of eight pairs of gold nano-resonators that are separated from a gold ground plane by a thin silicon dioxide spacer. Our experimental measurements reveal high-performance absorption over a wide range of incidence angles for both s- and p-polarizations. We also investigate numerically the frequency-dependent field and current distributions to elucidate how the absorption occurs within the metasurface structure. PMID:26828999

  5. Metasurface Broadband Solar Absorber

    DOE PAGES

    Azad, Abul K.; Kort-Kamp, Wilton J. M.; Sykora, Milan; ...

    2016-02-01

    Here, we demonstrate a broadband, polarization independent, wide-angle absorber based on a metallic metasurface architecture, which accomplishes greater than 90% absorptance in the visible and near-infrared range of the solar spectrum, and exhibits low absorptivity (emissivity) at mid- and far-infrared wavelengths. The complex unit cell of the metasurface solar absorber consists of eight pairs of gold nano-resonators that are separated from a gold ground plane by a thin silicon dioxide spacer. Moreover, our experimental measurements reveal high-performance absorption over a wide range of incidence angles for both s- and p-polarizations. We also investigate numerically the frequency-dependent field and current distributionsmore » to elucidate how the absorption occurs within the metasurface structure.« less

  6. Metasurface Broadband Solar Absorber

    SciTech Connect

    Azad, Abul K.; Kort-Kamp, Wilton J. M.; Sykora, Milan; Weisse-Bernstein, Nina R.; Luk, Ting S.; Taylor, Antoinette J.; Dalvit, Diego A. R.; Chen, Hou-Tong

    2016-02-01

    Here, we demonstrate a broadband, polarization independent, wide-angle absorber based on a metallic metasurface architecture, which accomplishes greater than 90% absorptance in the visible and near-infrared range of the solar spectrum, and exhibits low absorptivity (emissivity) at mid- and far-infrared wavelengths. The complex unit cell of the metasurface solar absorber consists of eight pairs of gold nano-resonators that are separated from a gold ground plane by a thin silicon dioxide spacer. Moreover, our experimental measurements reveal high-performance absorption over a wide range of incidence angles for both s- and p-polarizations. We also investigate numerically the frequency-dependent field and current distributions to elucidate how the absorption occurs within the metasurface structure.

  7. Ionized Absorbers in AGN

    NASA Technical Reports Server (NTRS)

    Mathur, S.

    1999-01-01

    As a part of this program, we observed three AGN:PKS2251 + 113, PG0043 = 039 and PLH909. Two objects show signatures of absorbtion in their UV spectra. Based on our earlier modeling of X-ray warm absorbents, we expected to observe X-ray observation in these objects. The third, PLH909, is known to have soft excess in EINSTEIN data. Attachment: "Exploratory ASCA observation of broad absorption line quasi-stellar objects".

  8. Apollo couch energy absorbers

    NASA Technical Reports Server (NTRS)

    Wesselski, C. J.; Drexel, R. E.

    1972-01-01

    Load attenuators for the Apollo spacecraft crew couch and its potential applications are described. Energy absorption is achieved through friction and cyclic deformation of material. In one concept, energy absorption is accomplished by rolling a compressed ring of metal between two surfaces. In another concept, energy is absorbed by forcing a plastically deformed washer along a rod. Among the design problems that had to be solved were material selection, fatigue life, ring slippage, lubrication, and friction loading.

  9. Absorber for terahertz radiation management

    SciTech Connect

    Biallas, George Herman; Apeldoorn, Cornelis; Williams, Gwyn P.; Benson, Stephen V.; Shinn, Michelle D.; Heckman, John D.

    2015-12-08

    A method and apparatus for minimizing the degradation of power in a free electron laser (FEL) generating terahertz (THz) radiation. The method includes inserting an absorber ring in the FEL beam path for absorbing any irregular THz radiation and thus minimizes the degradation of downstream optics and the resulting degradation of the FEL output power. The absorber ring includes an upstream side, a downstream side, and a plurality of wedges spaced radially around the absorber ring. The wedges form a scallop-like feature on the innermost edges of the absorber ring that acts as an apodizer, stopping diffractive focusing of the THz radiation that is not intercepted by the absorber. Spacing between the scallop-like features and the shape of the features approximates the Bartlett apodization function. The absorber ring provides a smooth intensity distribution, rather than one that is peaked on-center, thereby eliminating minor distortion downstream of the absorber.

  10. Corrosion resistant neutron absorbing coatings

    DOEpatents

    Choi, Jor-Shan [El Cerrito, CA; Farmer, Joseph C [Tracy, CA; Lee, Chuck K [Hayward, CA; Walker, Jeffrey [Gaithersburg, MD; Russell, Paige [Las Vegas, NV; Kirkwood, Jon [Saint Leonard, MD; Yang, Nancy [Lafayette, CA; Champagne, Victor [Oxford, PA

    2012-05-29

    A method of forming a corrosion resistant neutron absorbing coating comprising the steps of spray or deposition or sputtering or welding processing to form a composite material made of a spray or deposition or sputtering or welding material, and a neutron absorbing material. Also a corrosion resistant neutron absorbing coating comprising a composite material made of a spray or deposition or sputtering or welding material, and a neutron absorbing material.

  11. Corrosion resistant neutron absorbing coatings

    DOEpatents

    Choi, Jor-Shan; Farmer, Joseph C; Lee, Chuck K; Walker, Jeffrey; Russell, Paige; Kirkwood, Jon; Yang, Nancy; Champagne, Victor

    2013-11-12

    A method of forming a corrosion resistant neutron absorbing coating comprising the steps of spray or deposition or sputtering or welding processing to form a composite material made of a spray or deposition or sputtering or welding material, and a neutron absorbing material. Also a corrosion resistant neutron absorbing coating comprising a composite material made of a spray or deposition or sputtering or welding material, and a neutron absorbing material.

  12. Novel shock absorber features varying yield strengths

    NASA Technical Reports Server (NTRS)

    Geier, D. J.

    1964-01-01

    A shock absorbent webbing of partially drawn synthetic strands is arranged in sections of varying density related to the varying mass of the human body. This is contoured to protect the body at points of contact, when subjected to large acceleration or deceleration forces.

  13. Torus elements used in effective shock absorber

    NASA Technical Reports Server (NTRS)

    Cunningham, P.; Platus, D. L.

    1966-01-01

    Energy absorbing device forces torus elements to revolve annularly between two concentric tubes when a load is applied to one tube. Interference forces can be varied by using torus elements of different thicknesses. The device operates repeatedly in compression or tension, and under problems of large onset rate tolerance or structural overload.

  14. Solar radiation absorbing material

    DOEpatents

    Googin, John M.; Schmitt, Charles R.; Schreyer, James M.; Whitehead, Harlan D.

    1977-01-01

    Solar energy absorbing means in solar collectors are provided by a solar selective carbon surface. A solar selective carbon surface is a microporous carbon surface having pores within the range of 0.2 to 2 micrometers. Such a surface is provided in a microporous carbon article by controlling the pore size. A thermally conductive substrate is provided with a solar selective surface by adhering an array of carbon particles in a suitable binder to the substrate, a majority of said particles having diameters within the range of about 0.2-10 microns.

  15. Durability of Polymeric Glazing and Absorber Materials

    SciTech Connect

    Jorgensen, G.; Terwilliger, K.; Bingham, C.; Lindquist, C.; Milbourne, M.

    2005-11-01

    The Solar Heating and Lighting Program has set the goal of reducing the cost of solar water heating systems by at least 50%. An attractive approach to such large cost reduction is to replace glass and metal parts with less-expensive, lighter-weight, more-integrated polymeric components. The key challenge with polymers is to maintain performance and assure requisite durability for extended lifetimes. We have begun evaluation of several new UV-screened polycarbonate sheet glazing constructions. This has involved interactions with several major polymer industry companies to obtain improved candidate samples. Proposed absorber materials were tested for UV resistance, and appear adequate for unglazed ICS absorbers.

  16. Liquid Cryogen Absorber for MICE

    SciTech Connect

    Baynham, D.E.; Bish, P.; Bradshaw, T.W.; Cummings, M.A.; Green,M.A.; Ishimoto, S.; Ivaniouchenkov, I.; Lau, W.; Yang, S.Q.; Zisman, M.S.

    2005-08-20

    The Muon Ionization Cooling Experiment (MICE) will test ionization cooling of muons. In order to have effective ionization cooling, one must use an absorber that is made from a low-z material. The most effective low z materials for ionization cooling are hydrogen, helium, lithium hydride, lithium and beryllium, in that order. In order to measure the effect of material on cooling, several absorber materials must be used. This report describes a liquid-hydrogen absorber that is within a pair of superconducting focusing solenoids. The absorber must also be suitable for use with liquid helium. The following absorber components are discussed in this report; the absorber body, its heat exchanger, the hydrogen system, and the hydrogen safety. Absorber cooling and the thin windows are not discussed here.

  17. Optimal active vibration absorber: Design and experimental results

    NASA Technical Reports Server (NTRS)

    Lee-Glauser, Gina; Juang, Jer-Nan; Sulla, Jeffrey L.

    1992-01-01

    An optimal active vibration absorber can provide guaranteed closed-loop stability and control for large flexible space structures with collocated sensors/actuators. The active vibration absorber is a second-order dynamic system which is designed to suppress any unwanted structural vibration. This can be designed with minimum knowledge of the controlled system. Two methods for optimizing the active vibration absorber parameters are illustrated: minimum resonant amplitude and frequency matched active controllers. The Controls-Structures Interaction Phase-1 Evolutionary Model at NASA LaRC is used to demonstrate the effectiveness of the active vibration absorber for vibration suppression. Performance is compared numerically and experimentally using acceleration feedback.

  18. Direct Retrieval of Sulfur Dioxide Amount and Altitude from Spaceborne Hyperspectral UV Measurements: Theory and Application

    NASA Technical Reports Server (NTRS)

    Yang, Kau; Liu, Xiong; Bhartia, Pawan K.; Krotkov, Nickolay A.; Carn, Simon A.; Hughes, Eric J.; Krueger, Arlin J.; Spurr, Robert D.; Trahan, Samuel G.

    2010-01-01

    We describe the physical processes by which a vertically localized absorber perturbs the top-of-atmosphere solar backscattered ultraviolet (UV) radiance. The distinct spectral responses to perturbations of an absorber in its column amount and layer altitude provide the basis for a practical satellite retrieval technique, the Extended Iterative Spectral Fitting (EISF) algorithm, for the simultaneous retrieval of these quantities of a SO2 plume. In addition, the EISF retrieval provides an improved UV aerosol index for quantifying the spectral contrast of apparent scene reflectance at the bottom of atmosphere bounded by the surface and/or cloud; hence it can be used for detection of the presence or absence of UV absorbing aerosols. We study the performance and characterize the uncertainties of the EISF algorithm using synthetic backscattered UV radiances, retrievals from which can be compared with those used in the simulation. Our findings indicate that the presence of aerosols (both absorbing and nonabsorbing) does not cause large errors in EISF retrievals under most observing conditions when they are located below the SO2 plume. The EISF retrievals assuming a homogeneous field of view can provide accurate column amounts for inhomogeneous scenes, but they always underestimate the plume altitudes. The EISF algorithm reduces systematic errors present in existing linear retrieval algorithms that use prescribed SO2 plume heights. Applying the EISF algorithm to Ozone Monitoring Instrument satellite observations of the recent Kasatochi volcanic eruption, we demonstrate the successful retrieval of effective plume altitude of volcanic SO2, and we also show the improvement in accuracy in the corresponding SO2 columns.

  19. Preliminary sizing of vibration absorber for space mast structures

    NASA Technical Reports Server (NTRS)

    Card, M. F.; Mccomb, H. G., Jr.; Peebles, S. W.

    1982-01-01

    A simple method of sizing a vibration absorber for a large, cantilevered flexible mast is presented. The method is based on Den Hartog's vibration absorber theory for two-degree-of-freedom systems. Generalized design curves are presented as well as specific numerical results for a candidate space experiment in which a long flexible antenna mast is attached to the shuttle orbiter and dynamically excited by orbiter accelerations. Results indicate that for large flexible masts, the mass of the vibration absorber required to meet stringent tip deflection tolerances becomes prohibitively large.

  20. COSMIC DUST IN Mg II ABSORBERS

    SciTech Connect

    Menard, Brice; Fukugita, Masataka

    2012-08-01

    Mg II absorbers induce reddening on background quasars. We measure this effect and infer the cosmic density of dust residing in these systems to be {Omega} Almost-Equal-To 2 Multiplication-Sign 10{sup -6}, in units of the critical density of the universe, which is comparable to the amount of dust found in galactic disks or about half the amount inferred to exist outside galaxies. We also estimate the neutral hydrogen abundance in Mg II clouds to be {Omega} Almost-Equal-To 1.5 Multiplication-Sign 10{sup -4}, which is approximately 5% of hydrogen in stars in galaxies. This implies a dust-to-gas mass ratio for Mg II clouds of about 1/100, which is similar to the value for normal galaxies. This would support the hypothesis of the outflow origin of Mg II clouds, which are intrinsically devoid of stars and hence have no sources of dust. Considerations of the dust abundance imply that the presence of Mg II absorbers around galaxies lasts effectively for a few Gyr. High-redshift absorbers allow us to measure the rest-frame extinction curve to 900 A, at which the absorption by the Lyman edge dominates over scattering by dust in the extinction opacity.

  1. Ferroelectrics based absorbing layers

    NASA Astrophysics Data System (ADS)

    Hao, Jianping; Sadaune, Véronique; Burgnies, Ludovic; Lippens, Didier

    2014-07-01

    We show that ferroelectrics-based periodic structure made of BaSrTiO3 (BST) cubes, arrayed onto a metal plate with a thin dielectric spacer film exhibit a dramatic enhancement of absorbance with value close to unity. The enhancement is found around the Mie magnetic resonance of the Ferroelectrics cubes with the backside metal layer stopping any transmitted waves. It also involves quasi-perfect impedance matching resulting in reflection suppression via simultaneous magnetic and electrical activities. In addition, it was shown numerically the existence of a periodicity optimum, which is explained from surface waves analysis along with trade-off between the resonance damping and the intrinsic loss of ferroelectrics cubes. An experimental verification in a hollow waveguide configuration with a good comparison with full-wave numerical modelling is at last reported by measuring the scattering parameters of single and dual BST cubes schemes pointing out coupling effects for densely packed structures.

  2. Dual broadband metamaterial absorber.

    PubMed

    Kim, Young Ju; Yoo, Young Joon; Kim, Ki Won; Rhee, Joo Yull; Kim, Yong Hwan; Lee, YoungPak

    2015-02-23

    We propose polarization-independent and dual-broadband metamaterial absorbers at microwave frequencies. This is a periodic meta-atom array consisting of metal-dielectric-multilayer truncated cones. We demonstrate not only one broadband absorption from the fundamental magnetic resonances but additional broadband absorption in high-frequency range using the third-harmonic resonance, by both simulation and experiment. In simulation, the absorption was over 90% in 3.93-6.05 GHz, and 11.64-14.55 GHz. The corresponding experimental absorption bands over 90% were 3.88-6.08 GHz, 9.95-10.46 GHz and 11.86-13.84 GHz, respectively. The origin of absorption bands was elucidated. Furthermore, it is independent of polarization angle owing to the multilayered circular structures. The design is scalable to smaller size for the infrared and the visible ranges.

  3. THz-metamaterial absorbers

    NASA Astrophysics Data System (ADS)

    Tuong Pham, Van; Park, J. W.; Vu, Dinh Lam; Zheng, H. Y.; Rhee, J. Y.; Kim, K. W.; Lee, Y. P.

    2013-03-01

    An ultrabroad-band metamaterial absorber was investigated in mid-IR regime based on a similar model in previous work. The high absorption of metamaterial was obtained in a band of 8-11.7 THz with energy loss distributed in SiO2, which is appropriate potentially for solar-cell applications. A perfect absorption peak was provided by using a sandwich structure with periodical anti-dot pattern in the IR region, getting closed to visible-band metamaterials. The dimensional parameters were examined for the corresponding fabrication. Invited talk at the 6th International Workshop on Advanced Materials Science and Nanotechnology, 30 October-2 November, 2012, Ha Long, Vietnam.

  4. Electrochemically regenerable carbon dioxide absorber

    NASA Technical Reports Server (NTRS)

    Woods, R. R.; Marshall, R. D.; Schubert, F. H.; Heppner, D. B.

    1979-01-01

    Preliminary designs were generated for two electrochemically regenerable carbon dioxide absorber concepts. Initially, an electrochemically regenerable absorption bed concept was designed. This concept incorporated the required electrochemical regeneration components in the absorber design, permitting the absorbent to be regenerated within the absorption bed. This hardware was identified as the electrochemical absorber hardware. The second hardware concept separated the functional components of the regeneration and absorption process. This design approach minimized the extravehicular activity component volume by eliminating regeneration hardware components within the absorber. The electrochemical absorber hardware was extensively characterized for major operating parameters such as inlet carbon dioxide partial pressure, process air flow rate, operational pressure, inlet relative humidity, regeneration current density and absorption/regeneration cycle endurance testing.

  5. Broadband patterned magnetic microwave absorber

    SciTech Connect

    Li, Wei; Wu, Tianlong; Wang, Wei; Guan, Jianguo; Zhai, Pengcheng

    2014-07-28

    It is a tough task to greatly improve the working bandwidth for the traditional flat microwave absorbers because of the restriction of available material parameters. In this work, a simple patterning method is proposed to drastically broaden the absorption bandwidth of a conventional magnetic absorber. As a demonstration, an ultra-broadband microwave absorber with more than 90% absorption in the frequency range of 4–40 GHz is designed and experimentally realized, which has a thin thickness of 3.7 mm and a light weight equivalent to a 2-mm-thick flat absorber. In such a patterned absorber, the broadband strong absorption is mainly originated from the simultaneous incorporation of multiple λ/4 resonances and edge diffraction effects. This work provides a facile route to greatly extend the microwave absorption bandwidth for the currently available absorbing materials.

  6. Liquid Hydrogen Absorber for MICE

    SciTech Connect

    Ishimoto, S.; Suzuki, S.; Yoshida, M.; Green, Michael A.; Kuno, Y.; Lau, Wing

    2010-05-30

    Liquid hydrogen absorbers for the Muon Ionization Cooling Experiment (MICE) have been developed, and the first absorber has been tested at KEK. In the preliminary test at KEK we have successfully filled the absorber with {approx}2 liters of liquid hydrogen. The measured hydrogen condensation speed was 2.5 liters/day at 1.0 bar. No hydrogen leakage to vacuum was found between 300 K and 20 K. The MICE experiment includes three AFC (absorber focusing coil) modules, each containing a 21 liter liquid hydrogen absorber made of aluminum. The AFC module has safety windows to separate its vacuum from that of neighboring modules. Liquid hydrogen is supplied from a cryocooler with cooling power 1.5 W at 4.2 K. The first absorber will be assembled in the AFC module and installed in MICE at RAL.

  7. Membrane acoustic metamaterial absorbers with magnetic negative stiffness.

    PubMed

    Zhao, Junjuan; Li, Xianhui; Wang, Yueyue; Wang, Wenjiang; Zhang, Bin; Gai, Xiaoling

    2017-02-01

    A membrane absorber usually requires a large back cavity to achieve low-frequency sound absorption. This paper describes the design of a membrane acoustic metamaterial absorber in which magnetic negative stiffness is employed to reduce the size of the back cavity. As a baseline for the present research, analysis of a typical membrane sound absorber based on an equivalent circuit model is presented first. Then, a theoretical model is established by introducing negative stiffness into a standard absorber. It is demonstrated that a small cavity with negative stiffness can achieve the acoustic impedance of a large cavity and that the absorption peak is shifted to lower frequencies. Experimental results from an impedance tube test are also presented to validate this idea and show that negative stiffness can be employed to design compact low-frequency membrane absorbers.

  8. Energy absorber for the CETA

    NASA Technical Reports Server (NTRS)

    Wesselski, Clarence J.

    1994-01-01

    The energy absorber that was developed for the CETA (Crew Equipment and Translation Aid) on Space Station Freedom is a metal on metal frictional type and has a load regulating feature that prevents excessive stroking loads from occurring while in operation. This paper highlights some of the design and operating aspects and the testing of this energy absorber.

  9. Improvement Of The Helmholtz Absorber

    NASA Technical Reports Server (NTRS)

    Morrow, Duane L.

    1992-01-01

    Helmholtz-resonator system improved to enable it to absorb sound at more than one frequency without appreciable loss of effectiveness at primary frequency. Addition of annular cavities enables absorption of sound at harmonic frequencies in addition to primary frequency. Improved absorber designed for use on structures of high transmission loss. Applied to such machines as fixed-speed engines and fans.

  10. Metal-shearing energy absorber

    NASA Technical Reports Server (NTRS)

    Fay, R. J.; Wittrock, E. P.

    1971-01-01

    Device, consisting of tongue of thin aluminum alloy strip, pull tab, slotted steel plate which serves as cutter, and steel buckle, absorbs mechanical energy when its ends are subjected to tensile loading. Device is applicable as auxiliary shock absorbing anchor for automobile and airplane safety belts.

  11. Large-energy, narrow-bandwidth laser pulse at 1645 nm in a diode-pumped Er:YAG solid-state laser passively Q-switched by a monolayer graphene saturable absorber.

    PubMed

    Zhou, Rong; Tang, Pinghua; Chen, Yu; Chen, Shuqing; Zhao, Chujun; Zhang, Han; Wen, Shuangchun

    2014-01-10

    Nonlinear transmission parameters of monolayer graphene at 1645 nm were obtained. Based on the monolayer graphene saturable absorber, a 1532 nm LD pumped 1645 nm passively Q-switched Er:YAG laser was demonstrated. Under the pump power of 20.8 W, a 1645 nm Q-switched pulse with FWHM of 0.13 nm (without the use of etalon) and energy of 13.5 μJ per pulse can be obtained. To the best of our knowledge, this is the highest pulse energy for graphene-based passively Q-switched Er:YAG laseroperating at 1645 nm, suggesting the potentials of graphene materials for high-energy solid-state laser applications.

  12. Leaf absorbance and photosynthesis

    NASA Technical Reports Server (NTRS)

    Schurer, Kees

    1994-01-01

    The absorption spectrum of a leaf is often thought to contain some clues to the photosynthetic action spectrum of chlorophyll. Of course, absorption of photons is needed for photosynthesis, but the reverse, photosynthesis when there is absorption, is not necessarily true. As a check on the existence of absorption limits we measured spectra for a few different leaves. Two techniques for measuring absorption have been used, viz. the separate determination of the diffuse reflectance and the diffuse transmittance with the leaf at a port of an integrating sphere and the direct determination of the non-absorbed fraction with the leaf in the sphere. In a cross-check both methods yielded the same results for the absorption spectrum. The spectrum of a Fuchsia leaf, covering the short-wave region from 350 to 2500 nm, shows a high absorption in UV, blue and red, the well known dip in the green and a steep fall-off at 700 nm. Absorption drops to virtually zero in the near infrared, with subsequent absorptions, corresponding to the water absorption bands. In more detailed spectra, taken at 5 nm intervals with a 5 nm bandwidth, differences in chlorophyll content show in the different depths of the dip around 550 nm and in a small shift of the absorption edge at 700 nm. Spectra for Geranium (Pelargonium zonale) and Hibiscus (with a higher chlorophyll content) show that the upper limit for photosynthesis can not be much above 700 nm. No evidence, however, is to be seen of a lower limit for photosynthesis and, in fact, some experiments down to 300 nm still did not show a decrease of the absorption although it is well recognized that no photosynthesis results with 300 nm wavelengths.

  13. Absorbent product to absorb fluids. [for collection of human wastes

    NASA Technical Reports Server (NTRS)

    Dawn, F. S.; Correale, J. V. (Inventor)

    1982-01-01

    A multi-layer absorbent product for use in contact with the skin to absorb fluids is discussed. The product utilizes a water pervious facing layer for contacting the skin, overlayed by a first fibrous wicking layer, the wicking layer preferably being of the one-way variety in which fluid or liquid is moved away from the facing layer. The product further includes a first container section defined by inner and outer layer of a water pervious wicking material between which is disposed a first absorbent mass. A second container section defined by inner and outer layers between which is disposed a second absorbent mass and a liquid impermeable/gas permeable layer. Spacesuit applications are discussed.

  14. Thermally induced nonlinear optical absorption in metamaterial perfect absorbers

    SciTech Connect

    Guddala, Sriram Kumar, Raghwendra; Ramakrishna, S. Anantha

    2015-03-16

    A metamaterial perfect absorber consisting of a tri-layer (Al/ZnS/Al) metal-dielectric-metal system with top aluminium nano-disks was fabricated by laser-interference lithography and lift-off processing. The metamaterial absorber had peak resonant absorbance at 1090 nm and showed nonlinear absorption for 600ps laser pulses at 1064 nm wavelength. A nonlinear saturation of reflectance was measured to be dependent on the average laser power incident and not the peak laser intensity. The nonlinear behaviour is shown to arise from the heating due to the absorbed radiation and photo-thermal changes in the dielectric properties of aluminium. The metamaterial absorber is seen to be damage resistant at large laser intensities of 25 MW/cm{sup 2}.

  15. Thin-film infrared absorber structures for advanced thermal detectors

    NASA Astrophysics Data System (ADS)

    Parsons, A. D.; Pedder, D. J.

    1988-06-01

    Imaging thermal detector technology is a rapidly advancing field in which the current emphasis is towards the development of very large arrays of very small pyroelectric detector elements. For maximum responsivity, each of the thin pyroelectric elements in an array must be provided with a thermal absorber to convert incoming infrared radiation into heat. This paper describes one such absorber structure, comprising a thin metal film, impedance matched to free space, and a quarter-wave polymer film which offers an acceptably low thermal mass. The structure and properties of this thin-film absorber are compared with those of an electroplated platinum black absorber commonly used in thermal detectors. The theory of the absorber is presented and good agreement is shown between calculated and experimentally derived absorption spectra.

  16. Thermally induced nonlinear optical absorption in metamaterial perfect absorbers

    NASA Astrophysics Data System (ADS)

    Guddala, Sriram; Kumar, Raghwendra; Ramakrishna, S. Anantha

    2015-03-01

    A metamaterial perfect absorber consisting of a tri-layer (Al/ZnS/Al) metal-dielectric-metal system with top aluminium nano-disks was fabricated by laser-interference lithography and lift-off processing. The metamaterial absorber had peak resonant absorbance at 1090 nm and showed nonlinear absorption for 600ps laser pulses at 1064 nm wavelength. A nonlinear saturation of reflectance was measured to be dependent on the average laser power incident and not the peak laser intensity. The nonlinear behaviour is shown to arise from the heating due to the absorbed radiation and photo-thermal changes in the dielectric properties of aluminium. The metamaterial absorber is seen to be damage resistant at large laser intensities of 25 MW/cm2.

  17. An introduction to absorbent dressings.

    PubMed

    Jones, Menna Lloyd

    2014-12-01

    Exudate bathes the wound bed with a serous fluid that contains essential components that promote wound healing. However, excess exudate is often seen as a challenge for clinicians. Absorbent dressings are often used to aid in the management of exudate, with the aim of providing a moist but unmacerated environment. With so many different types of absorbent dressings available today-alongside making a holistic assessment-it is essential that clinicians also have the knowledge and skill to select the most appropriate absorbent dressing for a given patient.

  18. Self-Regulating Shock Absorber

    NASA Technical Reports Server (NTRS)

    Wesselski, Clarence J.

    1995-01-01

    Mechanical shock absorber keeps frictional damping force within tolerable limit. Its damping force does not increase with coefficient of friction between energy-absorbing components; rather, frictional damping force varies only slightly. Relatively insensitive to manufacturing variations and environmental conditions altering friction. Does not exhibit high breakaway friction and consequent sharp increase followed by sharp decrease in damping force at beginning of stroking. Damping force in absorber does not vary appreciably with speed of stroking. In addition, not vulnerable to leakage of hydraulic fluid.

  19. Spontaneous emission and absorber theory

    NASA Astrophysics Data System (ADS)

    Pegg, David T.

    1997-01-01

    One of the long term interests of George Series was the construction of a theory of spontaneous emission which does not involve field quantisation. His approach was written in terms of atomic operators only and he drew a parallel with the Wheeler-Feynman absorber theory of radiation. By making a particular extra postulate, he was able to obtain the correct spontaneous emission rate and the Lamb shift reasonably simply and directly. An examination of his approach indicates that this postulate is physically reasonable and the need for it arises because quantisation in his theory occurs after the response of the absorber has been accounted for by means of the radiative reaction field. We review briefly an alternative absorber theory approach to spontaneous emission based on the direct action between the emitting atom and a quantised absorber, and outline some applications to more recent effects of interest in quantum optics.

  20. Guided tissue regeneration. Absorbable barriers.

    PubMed

    Wang, H L; MacNeil, R L

    1998-07-01

    Over the past 15 years, techniques aimed at regeneration of lost periodontal tissue have become widely used and accepted in clinical practice. Among these techniques are those which use the principles of guided tissue regeneration (GTR), wherein barriers (i.e., membranes) are used to control cell and tissue repopulation of the periodontal wound. A variety of non-absorbable and absorbable barriers have been developed and used for this purpose, with a trend in recent years toward increased use of absorbable GTR materials. This article describes the evolution of absorbable barrier materials and overview materials available for clinical use today. In addition, advantages and disadvantages of these materials are discussed, as well as possible new developments in barrier-based GTR therapy.

  1. Shock wave absorber having apertured plate

    DOEpatents

    Shin, Y.W.; Wiedermann, A.H.; Ockert, C.E.

    1983-08-26

    The shock or energy absorber disclosed herein utilizes an apertured plate maintained under the normal level of liquid flowing in a piping system and disposed between the normal liquid flow path and a cavity pressurized with a compressible gas. The degree of openness (or porosity) of the plate is between 0.01 and 0.60. The energy level of a shock wave travelling down the piping system thus is dissipated by some of the liquid being jetted through the apertured plate toward the cavity. The cavity is large compared to the quantity of liquid jetted through the apertured plate, so there is little change in its volume. The porosity of the apertured plate influences the percentage of energy absorbed.

  2. Shock wave absorber having apertured plate

    DOEpatents

    Shin, Yong W.; Wiedermann, Arne H.; Ockert, Carl E.

    1985-01-01

    The shock or energy absorber disclosed herein utilizes an apertured plate maintained under the normal level of liquid flowing in a piping system and disposed between the normal liquid flow path and a cavity pressurized with a compressible gas. The degree of openness (or porosity) of the plate is between 0.01 and 0.60. The energy level of a shock wave travelling down the piping system thus is dissipated by some of the liquid being jetted through the apertured plate toward the cavity. The cavity is large compared to the quantity of liquid jetted through the apertured plate, so there is little change in its volume. The porosity of the apertured plate influences the percentage of energy absorbed.

  3. Countercurrent flow absorber and desorber

    DOEpatents

    Wilkinson, W.H.

    1984-10-16

    Countercurrent flow absorber and desorber devices are provided for use in absorption cycle refrigeration systems and thermal boosting systems. The devices have increased residence time and surface area resulting in improved heat and mass transfer characteristics. The apparatuses may be incorporated into open cycle thermal boosting systems in which steam serves both as the refrigerant vapor which is supplied to the absorber section and as the supply of heat to drive the desorber section of the system. 9 figs.

  4. Countercurrent flow absorber and desorber

    DOEpatents

    Wilkinson, William H.

    1984-01-01

    Countercurrent flow absorber and desorber devices are provided for use in absorption cycle refrigeration systems and thermal boosting systems. The devices have increased residence time and surface area resulting in improved heat and mass transfer characteristics. The apparatuses may be incorporated into open cycle thermal boosting systems in which steam serves both as the refrigerant vapor which is supplied to the absorber section and as the supply of heat to drive the desorber section of the system.

  5. Perfect selective metamaterial solar absorbers.

    PubMed

    Wang, Hao; Wang, Liping

    2013-11-04

    In this work, we numerically investigate the radiative properties of metamaterial nanostructures made of two-dimensional tungsten gratings on a thin dielectric spacer and an opaque tungsten film from UV to mid-infrared region as potential selective solar absorbers. The metamaterial absorber with single-sized tungsten patches exhibits high absorptance in the visible and near-infrared region due to several mechanisms such as surface plasmon polaritons, magnetic polaritons, and intrinsic bandgap absorption of tungsten. Geometric effects on the resonance wavelengths and the absorptance spectra are studied, and the physical mechanisms are elucidated in detail. The absorptance could be further enhanced in a broader spectral range with double-sized metamaterial absorbers. The total solar absorptance of the optimized metamaterial absorbers at normal incidence could be more than 88%, while the total emittance is less than 3% at 100°C, resulting in total photon-to-heat conversion efficiency of 86% without any optical concentration. Moreover, the metamaterial solar absorbers exhibit quasi-diffuse behaviors as well as polarization independence. The results here will facilitate the design of novel highly efficient solar absorbers to enhance the performance of various solar energy conversion systems.

  6. [Absorbed doses in dental radiology].

    PubMed

    Bianchi, S D; Roccuzzo, M; Albrito, F; Ragona, R; Anglesio, S

    1996-01-01

    The growing use of dento-maxillo-facial radiographic examinations has been accompanied by the publication of a large number of studies on dosimetry. A thorough review of the literature is presented in this article. Most studies were carried out on tissue equivalent skull phantoms, while only a few were in vivo. The aim of the present study was to evaluate in vivo absorbed doses during Orthopantomography (OPT). Full Mouth Periapical Examination (FMPE) and Intraoral Tube Panoramic Radiography (ITPR). Measurements were made on 30 patients, reproducing clinical conditions, in 46 anatomical sites, with 24 intra- and 22 extra-oral thermoluminiscent dosimeters (TLDS). The highest doses were measured, in orthopantomography, at the right mandibular angle (1899 mu Gy) in FMPE on the right naso-labial fold (5640 mu Gy and in ITPR on the palatal surface of the left second upper molar (1936 mu Gy). Intraoral doses ranged from 21 mu Gy, in orthopantomography, to 4494 mu Gy in FMPE. Standard errors ranged from 142% in ITPR to 5% in orthopantomography. The highest rate of standard errors was found in FMPE and ITPR. The data collected in this trial are in agreement with others in major literature reports. Disagreements are probably due to different exam acquisition and data collections. Such differences, presented comparison in several sites, justify lower doses in FMPE and ITPR. Advantages and disadvantages of in vivo dosimetry of the maxillary region are discussed, the former being a close resemblance to clinical conditions of examination and the latter the impossibility of collecting values in depth of tissues. Finally, both ITPR and FMPE required lower doses than expected, and can be therefore reconsidered relative to their radiation risk.

  7. Inferring Absorbing Organic Carbon Content from AERONET Data

    NASA Technical Reports Server (NTRS)

    Arola, A.; Schuster, G.; Myhre, G.; Kazadzis, S.; Dey, S.; Tripathi, S. N.

    2011-01-01

    Black carbon, light-absorbing organic carbon (often called brown carbon) and mineral dust are the major light-absorbing aerosols. Currently the sources and formation of brown carbon aerosol in particular are not well understood. In this study we estimated globally the amount of light absorbing organic carbon and black carbon from AERONET measurements. We find that the columnar absorbing organic carbon (brown carbon) levels in biomass burning regions of South-America and Africa are relatively high (about 15-20 magnesium per square meters during biomass burning season), while the concentrations are significantly lower in urban areas in US and Europe. However, we estimated significant absorbing organic carbon amounts from the data of megacities of newly industrialized countries, particularly in India and China, showing also clear seasonality with peak values up to 30-35 magnesium per square meters during the coldest season, likely caused by the coal and biofuel burning used for heating. We also compared our retrievals with the modeled organic carbon by global Oslo CTM for several sites. Model values are higher in biomass burning regions than AERONET-based retrievals, while opposite is true in urban areas in India and China.

  8. Additive manufacturing of RF absorbers

    NASA Astrophysics Data System (ADS)

    Mills, Matthew S.

    The ability of additive manufacturing techniques to fabricate integrated electromagnetic absorbers tuned for specific radio frequency bands within structural composites allows for unique combinations of mechanical and electromagnetic properties. These composites and films can be used for RF shielding of sensitive electromagnetic components through in-plane and out-of-plane RF absorption. Structural composites are a common building block of many commercial platforms. These platforms may be placed in situations in which there is a need for embedded RF absorbing properties along with structural properties. Instead of adding radar absorbing treatments to the external surface of existing structures, which adds increased size, weight and cost; it could prove to be advantageous to integrate the microwave absorbing properties directly into the composite during the fabrication process. In this thesis, a method based on additive manufacturing techniques of composites structures with prescribed electromagnetic loss, within the frequency range 1 to 26GHz, is presented. This method utilizes screen printing and nScrypt micro dispensing to pattern a carbon based ink onto low loss substrates. The materials chosen for this study will be presented, and the fabrication technique that these materials went through to create RF absorbing structures will be described. The calibration methods used, the modeling of the RF structures, and the applications in which this technology can be utilized will also be presented.

  9. Carbon Absorber Retrofit Equipment (CARE)

    SciTech Connect

    Klein, Eric

    2015-12-23

    During Project DE-FE0007528, CARE (Carbon Absorber Retrofit Equipment), Neumann Systems Group (NSG) designed, installed and tested a 0.5MW NeuStream® carbon dioxide (CO2) capture system using the patented NeuStream® absorber equipment and concentrated (6 molal) piperazine (PZ) as the solvent at Colorado Springs Utilities’ (CSU’s) Martin Drake pulverized coal (PC) power plant. The 36 month project included design, build and test phases. The 0.5MW NeuStream® CO2 capture system was successfully tested on flue gas from both coal and natural gas combustion sources and was shown to meet project objectives. Ninety percent CO2 removal was achieved with greater than 95% CO2product purity. The absorbers tested support a 90% reduction in absorber volume compared to packed towers and with an absorber parasitic power of less than 1% when configured for operation with a 550MW coal plant. The preliminary techno-economic analysis (TEA) performed by the Energy and Environmental Research Center (EERC) predicted an over-the-fence cost of $25.73/tonne of CO2 captured from a sub-critical PC plant.

  10. Optimization of Multilayer Laminated Film and Absorbent of Vacuum Insulation Panel for Use at High Temperature

    NASA Astrophysics Data System (ADS)

    Araki, Kuninari; Echigoya, Wataru; Tsuruga, Toshimitsu; Kamoto, Daigorou; Matsuoka, Shin-Ichi

    For the energy saving regulation and larger capacity, Vacuum Insulation Panel (VIP) has been used in refrigerators with urethane foam in recent years. VIP for low temperature is constructed by laminated plastic film, using heat welding of each neighboring part for keeping vacuum, so that the performance decrement is very large under high temperature. But recently high efficiency insulation material is desired for high temperature water holding devices (automatic vending machine, heat pump water heater, electric hot-water pot water, etc.), and we especially focused on cost and ability of the laminated plastic film and absorbent for high temperature VIP. We measured the heatproof temperature of plastic films and checked the amount of water vapor and out coming gas on temperature-programmed adsorption in absorbent. These results suggest the suitable laminated film and absorbent system for VIP use at high temperature, and the long-term reliability was evaluated by measuring thermal conductivity of high temperature. As a result it was found that high-retort pouch of CPP (cast polypropylene film) and adding of aluminum coating are the most suitable materials for use in the welded layers of high-temperature VIPs (105°C).

  11. Low temperature selective absorber research

    NASA Astrophysics Data System (ADS)

    Herzenberg, S. A.; Silberglitt, R.

    1982-04-01

    Research carried out since 1979 on selective absorbers is surveyed, with particular attention given to the low-temperature coatings seen as promising for flat plate and evacuated tube applications. The most thoroughly investigated absorber is black chrome, which is highly selective and is the most durable low-temperature absorber. It is believed that other materials, because of their low cost and lower content of strategic materials, may eventually supplant black chrome. Among these candidates are chemically converted black nickel; anodically oxidized nickel, zinc, and copper composites; and nickel or other low-cost multilayer coatings. In reviewing medium and high-temperature research, black chrome, multilayer coatings and black cobalt are seen as best medium-temperature candidates. For high temperatures, an Al2O3/Pt-Al203 multilayer composite or the zirconium diboride coating is preferred.

  12. Ultra-broadband microwave metamaterial absorber

    NASA Astrophysics Data System (ADS)

    Ding, Fei; Cui, Yanxia; Ge, Xiaochen; Jin, Yi; He, Sailing

    2012-03-01

    A microwave ultra-broadband polarization-independent metamaterial absorber is demonstrated. It is composed of a periodic array of metal-dielectric multilayered quadrangular frustum pyramids. These pyramids possess resonant absorption modes at multi-frequencies, of which the overlapping leads to the total absorption of the incident wave over an ultra-wide spectral band. The experimental absorption at normal incidence is above 90% in the frequency range of 7.8-14.7 GHz, and the absorption is kept large when the incident angle is smaller than 60°. The experimental results agree well with the numerical simulation.

  13. Magnetically tunable metamaterial perfect absorber

    NASA Astrophysics Data System (ADS)

    Lei, Ming; Feng, Ningyue; Wang, Qingmin; Hao, Yanan; Huang, Shanguo; Bi, Ke

    2016-06-01

    A magnetically tunable metamaterial perfect absorber (MPA) based on ferromagnetic resonance is experimentally and numerically demonstrated. The ferrite-based MPA is composed of an array of ferrite rods and a metallic ground plane. Frequency dependent absorption of the ferrite-based MPA under a series of applied magnetic fields is discussed. An absorption peak induced by ferromagnetic resonance appears in the range of 8-12 GHz under a certain magnetic field. Both the simulated and experimental results demonstrate that the absorption frequency of the ferrite-based MPA can be tuned by the applied magnetic field. This work provides an effective way to fabricate the magnetically tunable metamaterial perfect absorber.

  14. Adaptive inertial shock-absorber

    NASA Astrophysics Data System (ADS)

    Faraj, Rami; Holnicki-Szulc, Jan; Knap, Lech; Seńko, Jarosław

    2016-03-01

    This paper introduces and discusses a new concept of impact absorption by means of impact energy management and storage in dedicated rotating inertial discs. The effectiveness of the concept is demonstrated in a selected case-study involving spinning management, a recently developed novel impact-absorber. A specific control technique performed on this device is demonstrated to be the main source of significant improvement in the overall efficiency of impact damping process. The influence of various parameters on the performance of the shock-absorber is investigated. Design and manufacturing challenges and directions of further research are formulated.

  15. Damage tolerant light absorbing material

    DOEpatents

    Lauf, R.J.; Hamby, C. Jr.; Akerman, M.A.; Seals, R.D.

    1993-09-07

    A light absorbing article comprised of a composite of carbon-bonded carbon fibers, is prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000 C to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm[sup 3]. 9 figures.

  16. Damage tolerant light absorbing material

    DOEpatents

    Lauf, Robert J.; Hamby, Jr., Clyde; Akerman, M. Alfred; Seals, Roland D.

    1993-01-01

    A light absorbing article comprised of a composite of carbon-bonded carbon fibers, prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000.degree. C. to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm.sup.3.

  17. All-Silicon Ultra-Broadband Infrared Light Absorbers

    PubMed Central

    Gorgulu, Kazim; Gok, Abdullah; Yilmaz, Mehmet; Topalli, Kagan; Bıyıklı, Necmi; Okyay, Ali K.

    2016-01-01

    Absorbing infrared radiation efficiently is important for critical applications such as thermal imaging and infrared spectroscopy. Common infrared absorbing materials are not standard in Si VLSI technology. We demonstrate ultra-broadband mid-infrared absorbers based purely on silicon. Broadband absorption is achieved by the combined effects of free carrier absorption, and vibrational and plasmonic absorption resonances. The absorbers, consisting of periodically arranged silicon gratings, can be fabricated using standard optical lithography and deep reactive ion etching techniques, allowing for cost-effective and wafer-scale fabrication of micro-structures. Absorption wavebands in excess of 15 micrometers (5–20 μm) are demonstrated with more than 90% average absorptivity. The structures also exhibit broadband absorption performance even at large angles of incidence (θ = 50°), and independent of polarization. PMID:27924933

  18. Counterflow absorber for an absorption refrigeration system

    DOEpatents

    Reimann, Robert C.

    1984-01-01

    An air-cooled, vertical tube absorber for an absorption refrigeration system is disclosed. Strong absorbent solution is supplied to the top of the absorber and refrigerant vapor is supplied to the bottom of the absorber to create a direct counterflow of refrigerant vapor and absorbent solution in the absorber. The refrigeration system is designed so that the volume flow rate of refrigerant vapor in the tubes of the absorber is sufficient to create a substantially direct counterflow along the entire length of each tube in the absorber. This provides several advantages for the absorber such as higher efficiency and improved heat transfer characteristics, and allows improved purging of non-condensibles from the absorber.

  19. Metamaterial Absorbers for Microwave Detection

    DTIC Science & Technology

    2015-06-01

    a) Depiction of metamaterial array of square resonators atop FR4. (b) Metamaterial dimensions and structure...comparison for varying resonator array dimension sizes. ..............23 Figure 12. Absorption derived from raw reflection data...36 x Figure 23. Metamaterial absorber array where resonator dimensions control the detection frequencies and

  20. Wave based optimization of distributed vibration absorbers

    NASA Astrophysics Data System (ADS)

    Johnson, Marty; Batton, Brad

    2005-09-01

    The concept of distributed vibration absorbers or DVAs has been investigated in recent years as a method of vibration control and sound radiation control for large flexible structures. These devices are comprised of a distributed compliant layer with a distributed mass layer. When such a device is placed onto a structure it forms a sandwich panel configuration with a very soft core. With this configuration the main effect of the DVA is to create forces normal to the surface of the structure and can be used at low frequencies to either add damping, where constrain layer damper treatments are not very effective, or to pin the structure over a narrow frequency bandwidth (i.e., large input impedance/vibration absorber approach). This paper analyses the behavior of these devices using a wave based approach and finds an optimal damping level for the control of broadband disturbances in panels. The optimal design is calculated by solving the differential equations for waves propagating in coupled plates. It is shown that the optimal damping calculated using the infinite case acts as a good ``rule of thumb'' for designing DVAs to control the vibration of finite panels. This is bourn out in both numerical simulations and experiments.

  1. Measurements of Light Absorbing Particles on Tropical South American Glaciers

    NASA Astrophysics Data System (ADS)

    Schmitt, C. G.; All, J.; Schwarz, J. P.; Arnott, W. P.; Warthon, J.; Andrade, M.; Celestian, A. J.; Hoffmann, D.; Cole, R. J.; Lapham, E.; Horodyskyj, U. N.; Froyd, K. D.; Liao, J.

    2014-12-01

    Glaciers in the tropical Andes have been losing mass rapidly in recent decades. In addition to the documented increase in temperature, increases in light absorbing particulates deposited on glaciers could be contributing to the observed glacier loss. Here we present results of measurements of light absorbing particles from glaciers in Peru and Bolivia. Samples have been collected by American Climber Science Program volunteers and scientists at altitudes up to 6770 meters. Collected snow samples were melted and filtered in the field. A new inexpensive technique, the Light Absorption Heating Method (LAHM) has been developed for analysis of light absorbing particles collected on filters. Results from LAHM analysis are calibrated using filters with known amounts of fullerene soot, a common industrial surrogate for black carbon (BC). For snow samples collected at the same field location LAHM analysis and measurements from the Single Particle Soot Photometer (SP2) instrument are well correlated (r2 = 0.92). Co-located SP2 and LAHM filter analysis suggest that BC could be the dominant absorbing component of the light absorbing particles in some areas.

  2. Digital Alloy Absorber for Photodetectors

    NASA Technical Reports Server (NTRS)

    Hill, Cory J. (Inventor); Ting, David Z. (Inventor); Gunapala, Sarath D. (Inventor)

    2016-01-01

    In order to increase the spectral response range and improve the mobility of the photo-generated carriers (e.g. in an nBn photodetector), a digital alloy absorber may be employed by embedding one (or fraction thereof) to several monolayers of a semiconductor material (insert layers) periodically into a different host semiconductor material of the absorber layer. The semiconductor material of the insert layer and the host semiconductor materials may have lattice constants that are substantially mismatched. For example, this may performed by periodically embedding monolayers of InSb into an InAsSb host as the absorption region to extend the cutoff wavelength of InAsSb photodetectors, such as InAsSb based nBn devices. The described technique allows for simultaneous control of alloy composition and net strain, which are both key parameters for the photodetector operation.

  3. System size expansion for systems with an absorbing state.

    PubMed

    Di Patti, Francesca; Azaele, Sandro; Banavar, Jayanth R; Maritan, Amos

    2011-01-01

    The well-known van Kampen system size expansion, while of rather general applicability, is shown to fail to reproduce some qualitative features of the time evolution for systems with an absorbing state, apart from a transient initial time interval. We generalize the van Kampen ansatz by introducing a new prescription leading to non-Gaussian fluctuations around the absorbing state. The two expansion predictions are explicitly compared for the infinite range voter model with speciation as a paradigmatic model with an absorbing state. The new expansion, both for a finite size system in the large time limit and at finite time in the large size limit, converges to the exact solution as obtained in a numerical implementation using the Gillespie algorithm. Furthermore, the predicted lifetime distribution is shown to have the correct asymptotic behavior.

  4. Absorbed radiation by various tissues during simulated endodontic radiography

    SciTech Connect

    Torabinejad, M.; Danforth, R.; Andrews, K.; Chan, C.

    1989-06-01

    The amount of absorbed radiation by various organs was determined by placing lithium fluoride thermoluminescent chip dosimeters at selected anatomical sites in and on a human-like X-ray phantom and exposing them to radiation at 70- and 90-kV X-ray peaks during simulated endodontic radiography. The mean exposure dose was determined for each anatomical site. The results show that endodontic X-ray doses received by patients are low when compared with other radiographic procedures.

  5. Application of Intrared Absorbers to Nylon 6,6

    DTIC Science & Technology

    1974-07-01

    is trans- fered from the dyes to the IR 99, thus increasing the rate of photodegradation of IR 99. It should be noted that higher amounts of these...Physical) Infrared Infrared Radiation Textiles Nylon Dyes Nylon 6,6 Organic Salts Organic Compounds Salts Fluorescence 20. ABSTRACT... dyeing the nylon with an acid dye , or pre-treating it with certain organ- ic salts increased the uptake of infrared absorber, but light stability was

  6. Shock absorber operates over wide range

    NASA Technical Reports Server (NTRS)

    Creasy, W. K.; Jones, J. C.

    1965-01-01

    Piston-type hydraulic shock absorber, with a metered damping system, operates over a wide range of kinetic energy loading rates. It is used for absorbing shock and vibration on mounted machinery and heavy earth-moving equipment.

  7. 21 CFR 872.6050 - Saliva absorber.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... absorber is a device made of paper or cotton intended to absorb moisture from the oral cavity during dental... manufacturing practice requirements of the quality system regulation in part 820 of this chapter, with...

  8. Light-absorbing impurities in Arctic snow

    NASA Astrophysics Data System (ADS)

    Doherty, S. J.; Warren, S. G.; Grenfell, T. C.; Clarke, A. D.; Brandt, R. E.

    2010-12-01

    Absorption of radiation by ice is extremely weak at visible and near-ultraviolet wavelengths, so small amounts of light-absorbing impurities in snow can dominate the absorption of solar radiation at these wavelengths, reducing the albedo relative to that of pure snow, contributing to the surface energy budget and leading to earlier snowmelt. In this study Arctic snow is surveyed for its content of light-absorbing impurities, expanding and updating the 1983-1984 survey of Clarke and Noone. Samples were collected in Alaska, Canada, Greenland, Svalbard, Norway, Russia, and the Arctic Ocean during 1998 and 2005-2009, on tundra, glaciers, ice caps, sea ice, frozen lakes, and in boreal forests. Snow was collected mostly in spring, when the entire winter snowpack is accessible for sampling. Sampling was carried out in summer on the Greenland Ice Sheet and on the Arctic Ocean, of melting glacier snow and sea ice as well as cold snow. About 1200 snow samples have been analyzed for this study. The snow is melted and filtered; the filters are analyzed in a specially designed spectrophotometer system to infer the concentration of black carbon (BC), the fraction of absorption due to non-BC light-absorbing constituents and the absorption Ångstrom exponent of all particles. This is done using BC calibration standards having a mass absorption efficiency of 6.0 m2 g-1 at 550 nm and by making an assumption that the absorption Angstrom exponent for BC is 1.0 and for non-BC light-absorbing aerosol is 5.0. The reduction of snow albedo is primarily due to BC, but other impurities, principally brown (organic) carbon, are typically responsible for ~40% of the visible and ultraviolet absorption. The meltwater from selected snow samples was saved for chemical analysis to identify sources of the impurities. Median BC amounts in surface snow are as follows (nanograms of carbon per gram of snow): Greenland 3, Arctic Ocean snow 7, melting sea ice 8, Arctic Canada 8, subarctic Canada 14

  9. Reversibly tunable coupled and decoupled super absorbing structures

    NASA Astrophysics Data System (ADS)

    Zhang, Nan; Dong, Ziye; Ji, Dengxin; Song, Haomin; Zeng, Xie; Liu, Zhejun; Jiang, Suhua; Xu, Yun; Bernussi, Ayrton; Li, Wei; Gan, Qiaoqiang

    2016-02-01

    We differentiate the spacer-dependent peak shift in coupled and decoupled super absorbing structures based on magnetic resonance and interference mechanism, respectively, which is experimentally validated by low-cost and large-area structures fabricated using lithography-free processes. The reversible real-time spectral tunability is then demonstrated by incorporating a thermally tunable polymeric spacer layer.

  10. Calculation of interaction-induced spectra using complex absorbing potentials

    SciTech Connect

    Gustafsson, Magnus; Antipov, Sergey V.

    2010-10-29

    A complex absorbing potential method is implemented for calculation of collision-induced spectra. The scheme provides a way to avoid the integration of the Schroedinger equation to very large separations of the collisional pair. The method is tested by reproducing a previously computed absorption spectrum for H-He at two different temperatures.

  11. Improving the laboratory monitoring of absorbent oil

    SciTech Connect

    V.S. Shved; S.S. Sychev; I.V. Safina; S.A. Klykov

    2009-05-15

    The performance of absorbent coal tar oil is analyzed as a function of the constituent and group composition. The qualitative and quantitative composition of the oil that ensures the required absorbent properties is determined. Operative monitoring may be based on absorbent characteristics that permit regulation of the beginning and end of regeneration.

  12. Porcelain enamel neutron absorbing material

    DOEpatents

    Iverson, Daniel C.

    1990-02-06

    A porcelain enamel composition as a neutron absorbing material can be prepared of a major proportion by weight of a cadmium compound and a minor proportion of compounds of boron, lithium and silicon. These compounds in the form of a porcelain enamel coating or layer on several alloys has been found to be particularly effective in enhancing the nuclear safety of equipment for use in the processing and storage of fissile material. The composition of the porcelain enamel coating can be tailored to match the coefficient of thermal expansion of the equipment to be coated and excellent coating adhesion can be achieved.

  13. Porcelain enamel neutron absorbing material

    DOEpatents

    Iverson, D.C.

    1987-11-20

    A porcelain enamel composition as a neutron absorbing material can be prepared of a major proportion by weight of a cadmium compound and a minor proportion of compound of boron, lithium and silicon. These compounds in the form of a porcelain enamel coating or layer on several alloys has been found to be particularly effective in enhancing the nuclear safety of equipment for use in the processing and storage of fissile material. The composition of the porcelain enamel coating can be tailored to match the coefficient of thermal expansion of the equipment to be coated and excellent coating adhesion can be achieved. 2 figs.

  14. Porcelain enamel neutron absorbing material

    DOEpatents

    Iverson, Daniel C.

    1990-01-01

    A porcelain enamel composition as a neutron absorbing material can be prepared of a major proportion by weight of a cadmium compound and a minor proportion of compounds of boron, lithium and silicon. These compounds in the form of a porcelain enamel coating or layer on several alloys has been found to be particularly effective in enhancing the nuclear safety of equipment for use in the processing and storage of fissile material. The composition of the porcelain enamel coating can be tailored to match the coefficient of thermal expansion of the equipment to be coated and excellent coating adhesion can be achieved.

  15. Carbon dioxide absorbents for rebreather diving.

    PubMed

    Pennefather, John

    2016-09-01

    Firstly I would like to thank SPUMS members for making me a Life Member of SPUMS; I was surprised and greatly honoured by the award. I also want to confirm and expand on the findings on carbon dioxide absorbents reported by David Harvey et al. For about 35 years, I was the main player in deciding which absorbent went into Australian Navy and Army diving sets. On several occasions, suppliers of absorbents to the anaesthesia market tried to supply the Australian military market. On no occasion did they provide absorbent that came close to the minimum absorbent capacity required, generally being 30-40% less efficient than diving-grade absorbents. Because I regard lives as being more important than any likely dollar saving, the best absorbent was always selected unless two suppliers provided samples with the same absorbent capacity. On almost every occasion, there was a clear winner and cost was never considered. I suggest the same argument for the best absorbent should be used by members and their friends who dive using rebreather sets. I make this point because of my findings on a set that was brought to me after the death of its owner. The absorbent was not the type or grain size recommended by the manufacturer of the set and did not resemble any of the diving grade absorbents I knew of. I suspected by its appearance that it was anaesthetic grade absorbent. When I tested the set, the absorbent system failed very quickly so it is likely that carbon dioxide toxicity contributed to his death. The death was not the subject of an inquest and I have no knowledge of how the man obtained the absorbent. Possibly there was someone from an operating theatre staff who unintentionally caused their friend's death by supplying him with 'borrowed absorbent'. I make this point as I would like to discourage members from making a similar error.

  16. A polarization-independent broadband terahertz absorber

    SciTech Connect

    Shi, Cheng; Zang, XiaoFei E-mail: ymzhu@usst.edu.cn; Wang, YiQiao; Chen, Lin; Cai, Bin; Zhu, YiMing E-mail: ymzhu@usst.edu.cn

    2014-07-21

    A highly efficient broadband terahertz absorber is designed, fabricated, and experimentally as well as theoretically evaluated. The absorber comprises a heavily doped silicon substrate and a well-designed two-dimensional grating. Due to the destructive interference of waves and diffraction, the absorber can achieve over 95% absorption in a broad frequency range from 1 to 2 THz and for angles of incidence from 0° to 60°. Such a terahertz absorber is also polarization-independent due to its symmetrical structure. This omnidirectional and broadband absorber have potential applications in anti-reflection coatings, imaging systems, and so on.

  17. Polyamidoamine dendrimers as novel potential absorption enhancers for improving the small intestinal absorption of poorly absorbable drugs in rats.

    PubMed

    Lin, Yulian; Fujimori, Takeo; Kawaguchi, Naoko; Tsujimoto, Yuiko; Nishimi, Mariko; Dong, Zhengqi; Katsumi, Hidemasa; Sakane, Toshiyasu; Yamamoto, Akira

    2011-01-05

    Effects of polyamidoamine (PAMAM) dendrimers on the intestinal absorption of poorly absorbable drugs were examined by an in situ closed loop method in rats. 5(6)-Carboxyfluorescein (CF), fluorescein isothiocyanate-dextrans (FDs) with various molecular weights, calcitonin and insulin were used as model drugs of poorly absorbable drugs. The absorption of CF, FD4 and calcitonin from the rat small intestine was significantly enhanced in the presence of PAMAM dendrimers. The absorption-enhancing effects of PAMAM dendrimers for improving the small intestinal absorption of CF were concentration and generation dependent and a maximal absorption-enhancing effect was observed in the presence of 0.5% (w/v) G2 PAMAM dendrimer. However, G2 PAMAM dendrimer had almost no absorption-enhancing effect on the small intestinal absorption of macromolecular drugs including FD10 and insulin. Overall, the absorption-enhancing effects of G2 PAMAM dendrimer in the small intestine decreased as the molecular weights of drug increased. However, G2 PAMAM dendrimer did not enhance the intestinal absorption of these drugs with different molecular weights in the large intestine. Furthermore, we evaluated the intestinal membrane damage with or without G2 PAMAM dendrimer. G2 PAMAM dendrimer (0.5% (w/v)) significantly increased the activities of lactate dehydrogenase (LDH) and the amounts of protein released from the intestinal membranes, but the activities and amounts of these toxic markers were less than those in the presence of 3% Triton X-100 used as a positive control. Moreover, G2 PAMAM dendrimer at concentrations of 0.05% (w/v) and 0.1% (w/v) did not increase the activities and amounts of these toxic markers. These findings suggested that PAMAM dendrimers at lower concentrations might be potential and safe absorption enhancers for improving absorption of poorly absorbable drugs from the small intestine.

  18. Fabrication and microwave absorbing properties of NixPy nanotubes

    NASA Astrophysics Data System (ADS)

    Wang, Haoran; Wan, Lei; Chen, Yaqiong; Hu, Wenbin; Liu, Lei; Zhong, Cheng; Deng, Yida

    2015-06-01

    Materials possessing microwave absorbing properties have been a researching hotspot for their important applications amid a high frequency electromagnetic waves environment. This paper focuses on the preparation of a series of NixPy(x:y = 2.65-2.73) nanotubes (NTs) and their corresponding microwave absorbing properties. After being heat-treated, different NixPy phases would appear, without damaging their initial hollow morphologies. These processes were accompanied with the alteration of related physical properties. Low enough minimum reflection loss (RL) has been achieved in all of these samples, with -48.63 dB as the lowest one being obtained at the non-heat-treated sample. Besides, a large proportion of the microwave frequency band could be covered on the 450 °C heat-treated sample (over a 4.5 GHz bandwidth). These are indicative of the superior microwave absorbing nature of NixPy NTs.

  19. 46 CFR Sec. 2 - Amount of bond.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 8 2011-10-01 2011-10-01 false Amount of bond. Sec. 2 Section 2 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION A-NATIONAL SHIPPING AUTHORITY BONDING OF SHIP'S PERSONNEL Sec. 2 Amount of bond. The amount of the bond must be governed by the amount of monies advanced or value of...

  20. 46 CFR Sec. 2 - Amount of bond.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Amount of bond. Sec. 2 Section 2 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION A-NATIONAL SHIPPING AUTHORITY BONDING OF SHIP'S PERSONNEL Sec. 2 Amount of bond. The amount of the bond must be governed by the amount of monies advanced or value of...

  1. Characterization of metal oxide absorbents for regenerative carbon dioxide and water vapor removal for advanced portable life support systems

    NASA Technical Reports Server (NTRS)

    Kast, Timothy P.; Nacheff-Benedict, Maurena S.; Chang, Craig H.; Cusick, Robert J.

    1990-01-01

    Characterization of the performance of a silver-oxide-based absorbent in terms of its ability to remove both gaseous CO2 and water vapor in an astronaut portable life support systems (PLSS) is discussed. Attention is focused on regeneration of the absorbent from the carbonite state of the oxide state, preconditioning of the absorbent using a humidified gas stream, and absorption breakthrough testing. Based on the results of bench-scale experiments, a test plan is carried out to further characterize the silver-oxide-based absorbent on a larger scale; it calls for examination of the absorbent in both an adiabatic packed bed and a near-isothermal cooled bed configuration. It is demonstrated that the tested absorbent can be utilized in a way that removes substantial amounts of CO2 and water vapor during an 8-hour extravehicular activity mission, and that applying the absorbent to PLSS applications can simplify the ventilation loop.

  2. Frequency-tunable terahertz absorbers based on graphene metasurface

    NASA Astrophysics Data System (ADS)

    Chen, Ming; Sun, Wei; Cai, Jianjin; Chang, Linzi; Xiao, Xiaofei

    2017-01-01

    We present efficient designs of graphene-based thin absorbers, which are capable of near-unity absorption of the incident electromagnetic waves in the terahertz regime. Primarily, a single-frequency absorber is proposed. Subsequently, by simply stacking the double layer graphene metasurface with various geometric dimensions, the dual-frequency absorption and broadband absorption are realized respectively. Results demonstrate that the absorptivity of the single-frequency absorber reaches 99.51% at 2.71 THz when the Fermi energy is fixed at 0.9 eV. The dual-frequency absorber can simultaneously work at two frequencies with its absorptivity being 98.94% for 1.99 THz and 99.1% for 2.69 THz. The bandwidth of absorption rate above 90% expands three times when compared with the former single-frequency absorber. Additionally, it possesses the polarization-insensitive and large angle tolerance properties. More importantly, the absorption frequency can be dynamically controlled by adjusting Fermi energy levels without varying the nanostructure, which exhibits tremendous application values in many fields.

  3. Analysis and evaluation of RF absorbing material in suppressing modes associated with a metallic cavity

    NASA Astrophysics Data System (ADS)

    Green, David L.

    Application of absorbing materials within enclosures designed to house high-speed digital electronics has become common practice for suppressing resonances associated with the enclosure geometry. Use of absorbing material is often considered toward the end of the design phase when the product is undergoing electromagnetic compatibility compliance testing, leaving little time for the additional experimentation required to optimize absorber material selection or placement within the device. The engineering principles required for maximizing absorber performance within the enclosure are often disregarded, replaced by a "shotgun" approach where multiple material options are experimented with until a solution is achieved. For this research a frequency domain reverberation chamber technique and one-port time domain quality factor estimation technique are employed to quantify the ability of various absorbing materials to suppress resonances of a physically small, electrically large cavity representative of those that may be used to enclose high-speed circuitry. Using both measurement techniques, assessment of the performance of various absorbing materials was performed as well as an evaluation of the affect absorber position has on overall material performance. It was found that both measurement techniques were effective in quantifying absorber performance within the cavity. For the frequency domain reverberation chamber approach the absorber effectiveness, defined as the difference in insertion loss between the cavity with and without absorbing material, was analyzed for various materials. For the undermoded cavity it was found that absorber effectiveness was positionally dependent. For the overmoded cavity, however, the position of the absorber within the cavity, as long as the total exposed surface area remained constant, did not have a significant impact on the absorber effectiveness. Similar results were also found by comparing the estimated quality factor for

  4. Synthesis and characterization of a novel super-absorbent based on wheat straw.

    PubMed

    Ma, Zuohao; Li, Qian; Yue, Qinyan; Gao, Baoyu; Xu, Xing; Zhong, Qianqian

    2011-02-01

    In order to develop an eco-friendly polymer, a novel super-absorbent polymer was prepared by graft copolymerization of acrylic acid (AA), acrylic amide (AM) and dimethyl diallyl ammonium chloride (DMDAAC) onto the pretreatment wheat straw (PTWS). The molecular structure of the super-absorbent was confirmed by FTIR. The factors that can influence absorbencies of the super-absorbent resin (SAR) were investigated, such as weight ratio between the monomers, the ratio of PTWS to monomers, the amount of initiator and cross-linker, temperature reaction time and neutralization degree of AA. The SAR has the water absorbency of 133.76 g/g in distilled water and 33.83 g/g in 0.9 wt.% NaCl solution.

  5. Measurements of the light-absorbing material inside cloud droplets and its effect on cloud albedo

    NASA Technical Reports Server (NTRS)

    Twohy, C. H.; Clarke, A. D.; Warren, Stephen G.; Radke, L. F.; Charleson, R. J.

    1990-01-01

    Most of the measurements of light-absorbing aerosol particles made previously have been in non-cloudy air and therefore provide no insight into aerosol effects on cloud properties. Here, researchers describe an experiment designed to measure light absorption exclusively due to substances inside cloud droplets, compare the results to related light absorption measurements, and evaluate possible effects on the albedo of clouds. The results of this study validate those of Twomey and Cocks and show that the measured levels of light-absorbing material are negligible for the radiative properties of realistic clouds. For the measured clouds, which appear to have been moderately polluted, the amount of elemental carbon (EC) present was insufficient to affect albedo. Much higher contaminant levels or much larger droplets than those measured would be necessary to significantly alter the radiative properties. The effect of the concentrations of EC actually measured on the albedo of snow, however, would be much more pronounced since, in contrast to clouds, snowpacks are usually optically semi-infinite and have large particle sizes.

  6. Light-absorbing impurities in Arctic snow

    NASA Astrophysics Data System (ADS)

    Doherty, S. J.; Warren, S. G.; Grenfell, T. C.; Clarke, A. D.; Brandt, R. E.

    2010-08-01

    Absorption of radiation by ice is extremely weak at visible and near-ultraviolet wavelengths, so small amounts of light-absorbing impurities in snow can dominate the absorption of solar radiation at these wavelengths, reducing the albedo relative to that of pure snow, contributing to the surface energy budget and leading to earlier snowmelt. In this study Arctic snow is surveyed for its content of light-absorbing impurities, expanding and updating the 1983-1984 survey of Clarke and Noone. Samples were collected in Alaska, Canada, Greenland, Svalbard, Norway, Russia, and the Arctic Ocean during 2005-2009, on tundra, glaciers, ice caps, sea ice, frozen lakes, and in boreal forests. Snow was collected mostly in spring, when the entire winter snowpack is accessible for sampling. Sampling was carried out in summer on the Greenland ice sheet and on the Arctic Ocean, of melting glacier snow and sea ice as well as cold snow. About 1200 snow samples have been analyzed for this study. The snow is melted and filtered; the filters are analyzed in a specially designed spectrophotometer system to infer the concentration of black carbon (BC), the fraction of absorption due to non-BC light-absorbing constituents and the absorption Ångstrom exponent of all particles. The reduction of snow albedo is primarily due to BC, but other impurities, principally brown (organic) carbon, are typically responsible for ~40% of the visible and ultraviolet absorption. The meltwater from selected snow samples was saved for chemical analysis to identify sources of the impurities. Median BC amounts in surface snow are as follows (nanograms of carbon per gram of snow): Greenland 3, Arctic Ocean snow 7, melting sea ice 8, Arctic Canada 8, Subarctic Canada 14, Svalbard 13, Northern Norway 21, Western Arctic Russia 26, Northeastern Siberia 17. Concentrations are more variable in the European Arctic than in Arctic Canada or the Arctic Ocean, probably because of the proximity to BC sources. Individual

  7. Liquid crystal tunable metamaterial absorber.

    PubMed

    Shrekenhamer, David; Chen, Wen-Chen; Padilla, Willie J

    2013-04-26

    We present an experimental demonstration of electronically tunable metamaterial absorbers in the terahertz regime. By incorporation of active liquid crystal into strategic locations within the metamaterial unit cell, we are able to modify the absorption by 30% at 2.62 THz, as well as tune the resonant absorption over 4% in bandwidth. Numerical full-wave simulations match well to experiments and clarify the underlying mechanism, i.e., a simultaneous tuning of both the electric and magnetic response that allows for the preservation of the resonant absorption. These results show that fundamental light interactions of surfaces can be dynamically controlled by all-electronic means and provide a path forward for realization of novel applications.

  8. Oxalate: Effect on calcium absorbability

    SciTech Connect

    Heaney, R.P.; Weaver, C.M. )

    1989-10-01

    Absorption of calcium from intrinsically labeled Ca oxalate was measured in 18 normal women and compared with absorption of Ca from milk in these same subjects, both when the test substances were ingested in separate meals and when ingested together. Fractional Ca absorption from oxalate averaged 0.100 +/- 0.043 when ingested alone and 0.140 +/- 0.063 when ingested together with milk. Absorption was, as expected, substantially lower than absorption from milk (0.358 +/- 0.113). Nevertheless Ca oxalate absorbability in these women was higher than we had previously found for spinach Ca. When milk and Ca oxalate were ingested together, there was no interference of oxalate in milk Ca absorption and no evidence of tracer exchange between the two labeled Ca species.

  9. The 3D heat flux density distribution on a novel parabolic trough wavy absorber

    NASA Astrophysics Data System (ADS)

    Demagh, Yassine; Kabar, Yassine; Bordja, Lyes; Noui, Samira

    2016-05-01

    The non-uniform concentrated solar flux distribution on the outer surface of the absorber pipe can lead to large circumferential gradient temperature and high concentrated temperature of the absorber pipe wall, which is one of the primary causes of parabolic trough solar receiver breakdown. In this study, a novel shape of the parabolic trough absorber pipe is proposed as a solution to well homogenize the solar flux distribution, as well as, the temperature in the absorber wall. The conventional straight absorber located along the focal line of the parabola is replaced by wavy one (invention patent by Y. Demagh [1]) for which the heat flux density distribution on the outer surface varies in both axial and azimuthal directions (3D) while it varies only in the azimuthal direction on the former (2D). As far as we know, there is not previous study which has used a longitudinally wavy pipe as an absorber into the parabolic trough collector unit.

  10. Clearance of absorbed selenium by the liver

    SciTech Connect

    Kato, Tatsuko; Read, R.; Rozga, J.; Burk, R.F. )

    1991-03-11

    The liver plays a central role in the metabolism of selenium. It secretes plasma selenoproteins, contains a major fraction of the glutathione peroxidase in the body, and synthesizes excretory metabolites. The role of the liver in processing newly absorbed selenium was studied. Male chow-fed rats were fasted overnight and given 24 ng of selenium as {sup 75}SeO{sub 3}{sup 2{minus}} by stomach tube. Animals were exsanguinated at 15, 30, 45, 60, 90, 120, and 180 min after dosing. Comparison of {sup 75}Se uptake by liver, kidney, heart, muscle, testis, brain, and spleen indicated an earlier uptake by liver than by any other tissue. At 15 min, {sup 75}Se in the portal vein blood was 2.6 times that in the hepatic vein blood. Gel filtration analysis suggested a loose association of {sup 75}Se with protein in plasma at 15 min, but immunoprecipitation indicated it was largely in the form of selenoprotein P after 30 min. End-to-side portacaval shunts (PCS) were constructed in rats and sham-operated animals were used as controls. When {sup 75}SeO{sub 3}{sup 2{minus}} was given to animals with PCS, uptake of {sup 75}Se by liver did not precede uptake by other tissues. Also no gradient was detected across the lungs or kidney. {sup 75}Se content of the kidney was higher in PCS rats than in sham-operated rats. This is consistent with removal of the first-pass effect of the liver facilitating uptake of {sup 75}Se by systemic tissues. These results suggest that the preferential uptake of absorbed selenium by the liver is due both to its position in the portal circulation and to an intrinsic high uptake capacity.

  11. Molecular dynamic simulations of the water absorbency of hydrogels.

    PubMed

    Ou, Xiang; Han, Qiang; Dai, Hui-Hui; Wang, Jiong

    2015-09-01

    A polymer gel can imbibe solvent molecules through surface tension effect. When the solvent happens to be water, the gel can swell to a large extent and forms an aggregate called hydrogel. The large deformation caused by such swelling makes it difficult to study the behaviors of hydrogels. Currently, few molecular dynamic simulation works have been reported on the water absorbing mechanism of hydrogels. In this paper, we first use molecular dynamic simulation to study the water absorbing mechanism of hydrogels and propose a hydrogel-water interface model to study the water absorbency of the hydrogel surface. Also, the saturated water content and volume expansion rate of the hydrogel are investigated by building a hydrogel model with different cross-linking degree and by comparing the water absorption curves under different temperatures. The sample hydrogel model used consists of Polyethylene glycol diglycidyl ether (PEGDGE) as epoxy and the Jeffamine, poly-oxy-alkylene-amines, as curing agent. The conclusions obtained are useful for further investigation on PEGDGE/Jeffamine hydrogel. Moreover, the simulation methods, including hydrogel-water interface modeling, we first propose are also suitable to study the water absorbing mechanism of other hydrogels.

  12. Experimental realization of a terahertz all-dielectric metasurface absorber.

    PubMed

    Liu, Xinyu; Fan, Kebin; Shadrivov, Ilya V; Padilla, Willie J

    2017-01-09

    Metamaterial absorbers consisting of metal, metal-dielectric, or dielectric materials have been realized across much of the electromagnetic spectrum and have demonstrated novel properties and applications. However, most absorbers utilize metals and thus are limited in applicability due to their low melting point, high Ohmic loss and high thermal conductivity. Other approaches rely on large dielectric structures and / or a supporting dielectric substrate as a loss mechanism, thereby realizing large absorption volumes. Here we present a terahertz (THz) all dielectric metasurface absorber based on hybrid dielectric waveguide resonances. We tune the metasurface geometry in order to overlap electric and magnetic dipole resonances at the same frequency, thus achieving an experimental absorption of 97.5%. A simulated dielectric metasurface achieves a total absorption coefficient enhancement factor of FT=140, with a small absorption volume. Our experimental results are well described by theory and simulations and not limited to the THz range, but may be extended to microwave, infrared and optical frequencies. The concept of an all-dielectric metasurface absorber offers a new route for control of the emission and absorption of electromagnetic radiation from surfaces with potential applications in energy harvesting, imaging, and sensing.

  13. 29 CFR 4219.13 - Amount of liability for de minimis amounts.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 9 2010-07-01 2010-07-01 false Amount of liability for de minimis amounts. 4219.13 Section... Redetermination of Withdrawal Liability Upon Mass Withdrawal § 4219.13 Amount of liability for de minimis amounts. An employer that is liable for de minimis amounts shall be liable to the plan for the amount by...

  14. 29 CFR 4219.13 - Amount of liability for de minimis amounts.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 9 2011-07-01 2011-07-01 false Amount of liability for de minimis amounts. 4219.13 Section... Redetermination of Withdrawal Liability Upon Mass Withdrawal § 4219.13 Amount of liability for de minimis amounts. An employer that is liable for de minimis amounts shall be liable to the plan for the amount by...

  15. 29 CFR 4219.13 - Amount of liability for de minimis amounts.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 9 2012-07-01 2012-07-01 false Amount of liability for de minimis amounts. 4219.13 Section... Redetermination of Withdrawal Liability Upon Mass Withdrawal § 4219.13 Amount of liability for de minimis amounts. An employer that is liable for de minimis amounts shall be liable to the plan for the amount by...

  16. 29 CFR 4219.13 - Amount of liability for de minimis amounts.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 9 2014-07-01 2014-07-01 false Amount of liability for de minimis amounts. 4219.13 Section... Redetermination of Withdrawal Liability Upon Mass Withdrawal § 4219.13 Amount of liability for de minimis amounts. An employer that is liable for de minimis amounts shall be liable to the plan for the amount by...

  17. 29 CFR 4219.13 - Amount of liability for de minimis amounts.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 9 2013-07-01 2013-07-01 false Amount of liability for de minimis amounts. 4219.13 Section... Redetermination of Withdrawal Liability Upon Mass Withdrawal § 4219.13 Amount of liability for de minimis amounts. An employer that is liable for de minimis amounts shall be liable to the plan for the amount by...

  18. Magnetic field effects on microwave absorbing materials

    NASA Technical Reports Server (NTRS)

    Goldberg, Ira; Hollingsworth, Charles S.; Mckinney, Ted M.

    1991-01-01

    The objective of this program was to gather information to formulate a microwave absorber that can work in the presence of strong constant direct current (DC) magnetic fields. The program was conducted in four steps. The first step was to investigate the electrical and magnetic properties of magnetic and ferrite microwave absorbers in the presence of strong magnetic fields. This included both experimental measurements and a literature survey of properties that may be applicable to finding an appropriate absorbing material. The second step was to identify those material properties that will produce desirable absorptive properties in the presence of intense magnetic fields and determine the range of magnetic field in which the absorbers remain effective. The third step was to establish ferrite absorber designs that will produce low reflection and adequate absorption in the presence of intense inhomogeneous static magnetic fields. The fourth and final step was to prepare and test samples of such magnetic microwave absorbers if such designs seem practical.

  19. Evaluation of absorbed dose in Gadolinium neutron capture therapy

    NASA Astrophysics Data System (ADS)

    Abdullaeva, Gayane; Djuraeva, Gulnara; Kim, Andrey; Koblik, Yuriy; Kulabdullaev, Gairatulla; Rakhmonov, Turdimukhammad; Saytjanov, Shavkat

    2015-02-01

    Gadolinium neutron capture therapy (GdNCT) is used for treatment of radioresistant malignant tumors. The absorbed dose in GdNCT can be divided into four primary dose components: thermal neutron, fast neutron, photon and natural gadolinium doses. The most significant is the dose created by natural gadolinium. The amount of gadolinium at the irradiated region is changeable and depends on the gadolinium delivery agent and on the structure of the location where the agent is injected. To de- fine the time dependence of the gadolinium concentration ρ(t) in the irradiated region the pharmacokinetics of gadolinium delivery agent (Magnevist) was studied at intratumoral injection in mice and intramuscular injection in rats. A polynomial approximation was applied to the experimental data and the influence of ρ(t) on the relative change of the absorbed dose of gadolinium was studied.

  20. Applications of UV Scattering and Absorbing Aerosol Indices

    NASA Astrophysics Data System (ADS)

    Penning de Vries, M.; Beirle, S.; Wagner, T.

    2009-04-01

    Aerosols cause a substantial amount of radiative forcing, but quantifying this amount is difficult: determining aerosol concentrations in the atmosphere and, especially, characterizing their (optical) properties, has proved to be quite a challenge. A good way to monitor aerosol characteristics on a global scale is to perform satellite remote sensing. Most satellite aerosol retrieval algorithms are based on fitting of aerosol-induced changes in earth reflectance, which are usually subtle and have a smooth wavelength dependence. In such algorithms certain aerosol models are assumed, where optical parameters such as single scattering albedo, asymmetry parameter and size parameter (or Angstrom exponent) are defined. Another, semi-quantitative technique for detecting aerosols is the calculation of UV Aerosol Indices (UVAI). The Absorbing and Scattering Aerosol Indices detect "UV-absorbing" aerosols (most notably mineral dust, black and brown carbon particles) and "scattering" aerosols (sulfate and secondary organic aerosol particles), respectively. UVAI are essentially a measure of the contrast between two wavelengths in the UV range. The advantages of UVAI are: they can be determined in the presence of clouds, they are rather insensitive to surface type, and they are very sensitive to aerosols. The Absorbing Aerosol Index (AAI) has been in use for over a decade, and the Scattering Aerosol Index (SAI) was recently introduced by our group. Whereas the AAI is mainly used to detect desert dust and biomass burning plumes, the SAI can be used to study regions with high concentrations of non-absorbing aerosols, either anthropogenic (e.g. sulfate aerosols in eastern China) or biogenic (e.g. secondary organic aerosols formed from VOCs emitted by plants). Here we will present our recent UVAI results from SCIAMACHY: we will discuss the seasonal trend of SAI, and correlate our UVAI data with other datasets such as trace gases (HCHO, NO2, CO) and fire counts from the (A

  1. Absorbent product and articles made therefrom

    NASA Technical Reports Server (NTRS)

    Dawn, F. S.; Correale, J. V. (Inventor)

    1982-01-01

    A multilayer absorbent product for use in contact with the skin to absorb fluids is described. The product has a water pervious facing layer for contacting the skin, and a first fibrous wicking layer overlaying the water pervious layer. A first container section is defined by inner and outer layers of a water pervious wicking material in between a first absorbent mass and a second container section defined by inner and outer layers of a water pervious wicking material between what is disposed a second absorbent mass, and a liquid impermeable/gas permeable layer overlaying the second fibrous wicking layer.

  2. Metamaterial absorber with random dendritic cells

    NASA Astrophysics Data System (ADS)

    Zhu, Weiren; Zhao, Xiaopeng

    2010-05-01

    The metamaterial absorber composed of random dendritic cells has been investigated at microwave frequencies. It is found that the absorptivities come to be weaker and the resonant frequency get red shift as the disordered states increasing, however, the random metamaterial absorber still presents high absorptivity more than 95%. The disordered structures can help understanding of the metamaterial absorber and may be employed for practical design of infrared metamaterial absorber, which may play important roles in collection of radiative heat energy and directional transfer enhancement.

  3. Nature of the warm absorber outflow in NGC 4051

    NASA Astrophysics Data System (ADS)

    Mizumoto, Misaki; Ebisawa, Ken

    2017-04-01

    The narrow-line Seyfert 1 galaxy NGC 4051 is known to exhibit significant X-ray spectral/flux variations and have a number of emission/absorption features. X-ray observations have revealed that these absorption features are blueshifted, which indicates that NGC 4051 has warm absorber outflow. In order to constrain physical parameters of the warm absorber outflow, we analyse the archival data with the longest exposure taken by XMM-Newton in 2009. We calculate the root-mean-square (rms) spectra with the grating spectral resolution for the first time. The rms spectra have a sharp peak and several dips, which can be explained by variable absorption features and non-variable emission lines; a lower ionized warm absorber (WA1: log ξ = 1.5, v = -650 km s-1) shows large variability, whereas higher ionized warm absorbers (WA2: log ξ = 2.5, v = -4100 km s-1, WA3: log ξ = 3.4, v = -6100 km s-1) show little variability. WA1 shows the maximum variability at a time-scale of ∼104 s, suggesting that the absorber locates at ∼103 times of the Schwarzschild radius. The depth of the absorption features due to WA1 and the observed soft X-ray flux are anticorrelated in several observational sequences, which can be explained by variation of partial covering fraction of the double-layer blobs that are composed of the Compton-thick core and the ionized layer (=WA1). WA2 and WA3 show little variability and presumably extend uniformly in the line of sight. The present result shows that NGC 4051 has two types of the warm absorber outflows; the static, high-ionized and extended line-driven disc winds and the variable, low-ionized and clumpy double-layer blobs.

  4. Device for absorbing mechanical shock

    DOEpatents

    Newlon, C.E.

    1979-08-29

    This invention is a comparatively inexpensive but efficient shock-absorbing device having special application to the protection of shipping and storage cylinders. In a typical application, two of the devices are strapped to a cylinder to serve as saddle-type supports for the cylinder during storage and to protect the cylinder in the event it is dropped during lifting or lowering operations. In its preferred form, the invention includes a hardwood plank whose grain runs in the longitudinal direction. The basal portion of the plank is of solid cross-section, whereas the upper face of the plank is cut away to form a concave surface fittable against the sidewall of a storage cylinder. The concave surface is divided into a series of segments by transversely extending, throughgoing relief slots. A layer of elastomeric material is positioned on the concave face, the elastomer being extrudable into slots when pressed against the segments by a preselected pressure characteristic of a high-energy impact. The compressive, tensile, and shear properties of the hardwood and the elastomer are utilized in combination to provide a surprisingly high energy-absorption capability.

  5. Device for absorbing mechanical shock

    DOEpatents

    Newlon, Charles E.

    1980-01-01

    This invention is a comparatively inexpensive but efficient shock-absorbing device having special application to the protection of shipping and storage cylinders. In a typical application, two of the devices are strapped to a cylinder to serve as saddle-type supports for the cylinder during storage and to protect the cylinder in the event it is dropped during lifting or lowering operations. In its preferred form, the invention includes a hardwood plank whose grain runs in the longitudinal direction. The basal portion of the plank is of solid cross-section, whereas the upper face of the plank is cut away to form a concave surface fittable against the sidewall of a storage cylinder. The concave surface is divided into a series of segments by transversely extending, throughgoing relief slots. A layer of elastomeric material is positioned on the concave face, the elastomer being extrudable into slots when pressed against the segments by a preselected pressure characteristic of a high-energy impact. The compressive, tensile, and shear properties of the hardwood and the elastomer are utilized in combination to provide a surprisingly high energy-absorption capability.

  6. Absorbing Aerosols Workshop, January 20-21, 2016

    SciTech Connect

    Nasiri, Shaima; Williamson, Ashley; Cappa, Christopher D.; Kotamarthi, Davis Rao; Sedlacek, Arthur J.; Flynn, Conner; Lewis, Ernie; McComiskey, Allison; Riemer, Nicole

    2016-07-01

    A workshop was held at DOE Headquarters on January 20-21, 2016 during which experts within and outside DOE were brought together to identify knowledge gaps in modeling and measurement of the contribution of absorbing aerosols (AA) to radiative forcing. Absorbing aerosols refer to those aerosols that absorb light, whereby they both reduce the amount of sunlight reaching the surface (direct effect) and heat their surroundings. By doing so, they modify the vertical distribution of heat in the atmosphere and affect atmospheric thermodynamics and stability, possibly hastening cloud drop evaporation, and thereby affecting cloud amount, formation, dissipation and, ultimately, precipitation. Deposition of AA on snow and ice reduces surface albedo leading to accelerated melt. The most abundant AA type is black carbon (BC), which results from combustion of fossil fuel and biofuel. The other key AA types are brown carbon (BrC), which also results from combustion of fossil fuel and biofuel, and dust (crustal material). Each of these sources may result from, and be strongly influenced by, anthropogenic activities. The properties and amounts of AA depend upon various factors, primarily fuel source and burn conditions (e.g., internal combustion engine, flaming or smoldering wildfire), vegetation type (in the case of BC and BrC), and in the case of dust, soil type and ground cover (i.e., vegetation, snow, etc.). After emission, AA undergo chemical processing in the atmosphere that affects their physical and chemical properties. Thus, attribution of sources of AA, and understanding processes AA undergo during their atmospheric lifetimes, are necessary to understand how they will behave in a changing climate.

  7. Self-assembly of highly efficient, broadband plasmonic absorbers for solar steam generation.

    PubMed

    Zhou, Lin; Tan, Yingling; Ji, Dengxin; Zhu, Bin; Zhang, Pei; Xu, Jun; Gan, Qiaoqiang; Yu, Zongfu; Zhu, Jia

    2016-04-01

    The study of ideal absorbers, which can efficiently absorb light over a broad range of wavelengths, is of fundamental importance, as well as critical for many applications from solar steam generation and thermophotovoltaics to light/thermal detectors. As a result of recent advances in plasmonics, plasmonic absorbers have attracted a lot of attention. However, the performance and scalability of these absorbers, predominantly fabricated by the top-down approach, need to be further improved to enable widespread applications. We report a plasmonic absorber which can enable an average measured absorbance of ~99% across the wavelengths from 400 nm to 10 μm, the most efficient and broadband plasmonic absorber reported to date. The absorber is fabricated through self-assembly of metallic nanoparticles onto a nanoporous template by a one-step deposition process. Because of its efficient light absorption, strong field enhancement, and porous structures, which together enable not only efficient solar absorption but also significant local heating and continuous stream flow, plasmonic absorber-based solar steam generation has over 90% efficiency under solar irradiation of only 4-sun intensity (4 kW m(-2)). The pronounced light absorption effect coupled with the high-throughput self-assembly process could lead toward large-scale manufacturing of other nanophotonic structures and devices.

  8. In situ study of binding of copper by fulvic acid: comparison of differential absorbance data and model predictions.

    PubMed

    Yan, Mingquan; Dryer, Deborah; Korshin, Gregory V; Benedetti, Marc F

    2013-02-01

    This study examined the binding of copper(II) by Suwannee River fulvic acid (SRFA) using the method of differential absorbance that was used at environmentally-relevant concentrations of copper and SRFA. The pH- and metal-differential spectra were processed via numeric deconvolution to establish commonalities seen in the changes of absorbance caused by deprotonation of SRFA and its interactions with copper(II) ions. Six Gaussian bands were determined to be present in both the pH- and Cu-differential spectra. Their maxima were located, in the order of increasing wavelengths at 208 nm, 242 nm, 276 nm, 314 nm, 378 nm and 551 nm. The bands with these maxima were denoted as A0, A1, A2, A3, A4 and A5, respectively. Properties of these bands were compared with those existing in the spectra of model compounds such as sulfosalicylic acid (SSA), tannic acid (TA), and polystyrenesulfonic acid-co-maleic acid (PSMA). While none of the features observed in differential spectra of the model compound were identical to those present in the case of SRFA, Gaussian bands A1, A3 and possibly A2 were concluded to be largely attributable to a combination of responses of salicylic- and polyhydroxyphenolic groups. In contrast, bands A4 and A5 were detected in the differential spectra of SRFA only. Their nature remains to be elucidated. To examine correlations between the amount of copper(II) bound by SRFA and changes of its absorbance, differential absorbances measured at indicative wavelengths 250 nm and 400 nm were compared with the total amount of SRFA-bound copper estimated based on Visual MINTEQ calculations. This examination showed that the differential absorbances of SRFA in a wide range of pH values and copper concentrations were strongly correlated with the concentration of SRFA-bound copper. The approach presented in this study can be used to generate in situ information concerning the nature of functional groups in humic substances engaged in interactions with metals ions. This

  9. The amount effect and marginal value.

    PubMed

    Rachlin, Howard; Arfer, Kodi B; Safin, Vasiliy; Yen, Ming

    2015-07-01

    The amount effect of delay discounting (by which the value of larger reward amounts is discounted by delay at a lower rate than that of smaller amounts) strictly implies that value functions (value as a function of amount) are steeper at greater delays than they are at lesser delays. That is, the amount effect and the difference in value functions at different delays are actually a single empirical finding. Amount effects of delay discounting are typically found with choice experiments. Value functions for immediate rewards have been empirically obtained by direct judgment. (Value functions for delayed rewards have not been previously obtained.) The present experiment obtained value functions for both immediate and delayed rewards by direct judgment and found them to be steeper when the rewards were delayed--hence, finding an amount effect with delay discounting.

  10. Graphene-enabled electrically switchable radar-absorbing surfaces.

    PubMed

    Balci, Osman; Polat, Emre O; Kakenov, Nurbek; Kocabas, Coskun

    2015-03-20

    Radar-absorbing materials are used in stealth technologies for concealment of an object from radar detection. Resistive and/or magnetic composite materials are used to reduce the backscattered microwave signals. Inability to control electrical properties of these materials, however, hinders the realization of active camouflage systems. Here, using large-area graphene electrodes, we demonstrate active surfaces that enable electrical control of reflection, transmission and absorption of microwaves. Instead of tuning bulk material property, our strategy relies on electrostatic tuning of the charge density on an atomically thin electrode, which operates as a tunable metal in microwave frequencies. Notably, we report large-area adaptive radar-absorbing surfaces with tunable reflection suppression ratio up to 50 dB with operation voltages <5 V. Using the developed surfaces, we demonstrate various device architectures including pixelated and curved surfaces. Our results provide a significant step in realization of active camouflage systems in microwave frequencies.

  11. Graphene-enabled electrically switchable radar-absorbing surfaces

    NASA Astrophysics Data System (ADS)

    Balci, Osman; Polat, Emre O.; Kakenov, Nurbek; Kocabas, Coskun

    2015-03-01

    Radar-absorbing materials are used in stealth technologies for concealment of an object from radar detection. Resistive and/or magnetic composite materials are used to reduce the backscattered microwave signals. Inability to control electrical properties of these materials, however, hinders the realization of active camouflage systems. Here, using large-area graphene electrodes, we demonstrate active surfaces that enable electrical control of reflection, transmission and absorption of microwaves. Instead of tuning bulk material property, our strategy relies on electrostatic tuning of the charge density on an atomically thin electrode, which operates as a tunable metal in microwave frequencies. Notably, we report large-area adaptive radar-absorbing surfaces with tunable reflection suppression ratio up to 50 dB with operation voltages <5 V. Using the developed surfaces, we demonstrate various device architectures including pixelated and curved surfaces. Our results provide a significant step in realization of active camouflage systems in microwave frequencies.

  12. The HI Environment of Nearby Lyman-alpha Absorbers

    NASA Technical Reports Server (NTRS)

    VanGorkom, J. H.; Carilli, C. L.; Stocke, John T.; Perlman, Eric S.; Shull, J. Michael

    1996-01-01

    We present the results of a VLA and WSRT search for H I emission from the vicinity of seven nearby clouds, which were observed in Ly-alpha absorption with HST toward Mrk 335, Mrk 501, and PKS 2155-304. Around the absorbers, we searched a volume of 4O' x 40' x 1000 km/s; for one of the absorbers we probed a velocity range of only 600 km/s. The H I mass sensitivity (5 sigma) very close to the lines of sight varies from 5 x 10(exp 6) solar mass at best to 5 x 10(exp 8) solar mass at worst. We detected H I emission in the vicinity of four out of seven absorbers. The closest galaxy we find to the absorbers is a small dwarf galaxy at a projected distance of 68 h(exp -1) kpc from the sight line toward Mrk 335. This optically uncataloged galaxy has the same velocity (V = 1970 km/s) as one of the absorbers, is fainter than the SMC, and has an H I mass of only 4 x 10(exp 7) solar mass. We found a somewhat more luminous galaxy at exactly the velocity (V = 5100 km/s) of one of the absorbers toward PKS 2155-304 at a projected distance of 230 h(exp -1) kpc from the sight line. Two other, stronger absorbers toward PKS 2155-304 at V approx. 17,000 km/s appear to be associated with a loose group of three bright spiral galaxies, at projected distances of 300 to 600 h(exp -1) kpc. These results support the conclusions emerging from optical searches that most nearby Ly-alpha forest clouds trace the large-scale structures outlined by the optically luminous galaxies, although this is still based on small-number statistics. We do not find any evidence from the H I distribution or kinematics that there is a physical association between an absorber and its closest galaxy. While the absorbing clouds are at the systemic velocity of the galaxies, the H I extent of the galaxies is fairly typical, and at least an order of magnitude smaller than the projected distance to the sight line at which the absorbers are seen. On the other hand, we also do not find evidence against such a connection. In

  13. Absorbencies of six different rodent beddings: commercially advertised absorbencies are potentially misleading.

    PubMed

    Burn, C C; Mason, G J

    2005-01-01

    Moisture absorbency is one of the most important characteristics of rodent beddings for controlling bacterial growth and ammonia production. However, bedding manufacturers rarely provide information on the absorbencies of available materials, and even when they do, absorption values are usually expressed per unit mass of bedding. Since beddings are usually placed into cages to reach a required depth rather than a particular mass, their volumetric absorbencies are far more relevant. This study therefore compared the saline absorbencies of sawdust, aspen woodchips, two virgin loose pulp beddings (Alpha-Dri and Omega-Dri), reclaimed wood pulp (Tek-Fresh), and corncob, calculated both by volume and by mass. Absorbency per unit volume correlated positively with bedding density, while absorbency per unit mass correlated negatively. Therefore, the relative absorbencies of the beddings were almost completely reversed depending on how absorbency was calculated. By volume, corncob was the most absorbent bedding, absorbing about twice as much saline as Tek-Fresh, the least absorbent bedding. Conversely, when calculated by mass, Tek-Fresh appeared to absorb almost three times as much saline as the corncob. Thus, in practical terms the most absorbent bedding here was corncob, followed by the loose pulp beddings; and this is generally supported by their relatively low ammonia production as seen in previous studies. Many factors other than absorbency determine whether a material is suitable as a rodent bedding, and they are briefly mentioned here. However, manufacturers should provide details of bedding absorbencies in terms of volume, in order to help predict the relative absorbencies of the beddings in practical situations.

  14. An ultrathin dual-band metamaterial absorber

    NASA Astrophysics Data System (ADS)

    Zhang, Yong; Duan, Junping; Zhang, Wendong; Wang, Wanjun; Zhang, Binzhen

    2016-10-01

    The design and preparation of an ultrathin dual-band metamaterial absorber whose resonant frequency located at radar wave (20 GHz-60 GHz) is presented in this paper. The absorber is composed of a 2-D periodic sandwich featured with two concentric annuluses. The influence on the absorber's performance produced by resonant cell's structure size and material parameters was numerically simulated and analyzed based on the standard full wave finite integration technology in CST. Laser ablation process was adopted to prepare the designed absorber on epoxy resin board coated with on double plane of copper with a thickness that is 1/30 and 1/50 of the resonant wavelength at a resonant frequency of 30.51 GHz and 48.15 GHz. The full width at half maximum (FWHM) reached 2.2 GHz and 2.35 GHz and the peak of the absorptance reached 99.977%. The ultrathin absorber is nearly omnidirectional for all polarizations. The test results of prepared sample testify the designed absorber's excellent absorbing performance forcefully. The absorber expands inspirations of radar stealth in military domain due to its flexible design, cost-effective and other outstanding properties.

  15. 21 CFR 872.6050 - Saliva absorber.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Saliva absorber. 872.6050 Section 872.6050 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6050 Saliva absorber. (a) Identification. A...

  16. 21 CFR 872.6050 - Saliva absorber.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Saliva absorber. 872.6050 Section 872.6050 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6050 Saliva absorber. (a) Identification. A...

  17. Study on the electromagnetic properties of a coated radar absorbent

    NASA Astrophysics Data System (ADS)

    Zhang, Shuan-Qin

    2012-06-01

    The sol-gel method is used to fabricate Fe crystalline powders coated with SiO2. By controlling the molar ratio R of diluted water to tetraethoxysilane (TEOS), Fe powders coated with SiO2 with different morphological characteristics are fabricated. The influence of the core diameter on electromagnetic parameters is investigated. The effect of the amount of the coating material SiO2 on electromagnetic parameters is given. Radar wave absorbing properties of Fe coated with SiO2 and TiO2 respectively are compared.

  18. Seasonal Evolution and Interannual Variability of the Local Solar Energy Absorbed by the Arctic Sea Ice-Ocean System

    NASA Technical Reports Server (NTRS)

    Perovich, Donald K.; Nghiem, Son V.; Markus, Thorsten; Schwieger, Axel

    2007-01-01

    The melt season of the Arctic sea ice cover is greatly affected by the partitioning of the incident solar radiation between reflection to the atmosphere and absorption in the ice and ocean. This partitioning exhibits a strong seasonal cycle and significant interannual variability. Data in the period 1998, 2000-2004 were analyzed in this study. Observations made during the 1997-1998 SHEBA (Surface HEat Budget of the Arctic Ocean) field experiment showed a strong seasonal dependence of the partitioning, dominated by a five-phase albedo evolution. QuikSCAT scatterometer data from the SHEBA region in 1999-2004 were used to further investigate solar partitioning in summer. The time series of scatterometer data were used to determine the onset of melt and the beginning of freezeup. This information was combined with SSM/I-derived ice concentration, TOVS-based estimates of incident solar irradiance, and SHEBA results to estimate the amount of solar energy absorbed in the ice-ocean system for these years. The average total solar energy absorbed in the ice-ocean system from April through September was 900 MJ m(sup -2). There was considerable interannual variability, with a range of 826 to 1044 MJ m(sup -2). The total amount of solar energy absorbed by the ice and ocean was strongly related to the date of melt onset, but only weakly related to the total duration of the melt season or the onset of freezeup. The timing of melt onset is significant because the incident solar energy is large and a change at this time propagates through the entire melt season, affecting the albedo every day throughout melt and freezeup.

  19. Impact absorbing blade mounts for variable pitch blades

    NASA Technical Reports Server (NTRS)

    Ravenhall, R.; Salemme, C. T.; Adamson, A. P. (Inventor)

    1977-01-01

    A variable pitch blade and blade mount are reported that are suitable for propellers, fans and the like and which have improved impact resistance. Composite fan blades and blade mounting arrangements permit the blades to pivot relative to a turbine hub about an axis generally parallel to the centerline of the engine upon impact of a large foreign object, such as a bird. Centrifugal force recovery becomes the principal energy absorbing mechanism and a blade having improved impact strength is obtained.

  20. Radar Absorbing Colloidal Solutions (RACS)

    DTIC Science & Technology

    2007-08-01

    area is limited (e.g., thewiiig 4 a saU alkvmft), the design of a gd vaydifficult sinc precise control over some maghdic and dielecfi e properties is...has determined the amount of RF shielding of various SPM particles ( Fe O4 , MnZ^04 , and CoFeR2O4) in polymer matrices at similar frequencies [8]. In...parameterg and (b) insertion loss of the line standard when the standard is filled with Fe 󈧈 1 mg/mL partickes. In this case the standard, is only

  1. Impact of structural heterogeneity in solar absorber layers (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Toney, Michael

    2016-09-01

    Impact of structural heterogeneity in solar absorber layers Michael F Toney SLAC National Accelerator Laboratory Structural and morphological heterogeneity is common in thin film and emerging solar cell absorber layers, including organic photovoltaic bulk heterojunctions (OPV BHJs), hybrid organic-inorganic perovskites (HOIP), and Cu2ZnSn(S,Se)4 (CZTSSe), and has a significant impact on the (opto)electronic heterogeneity and hence absorber properties. In this talk I will use X-ray based methods, including scattering and spectroscopies, to characterize and quantify the heterogeneity in OPV BHJs and HOIP absorber layers. The BHJ films are blends of the small molecule X2 and [6,6]-phenyl C71 butyric acid methyl ester (PC71BM) where it has been established that there are three distinct region of the films - pure PC71BM, pure X2 and intimately mixed X2:PC71BM. This talk will show how the absolute concentration of the mixed phase can be used to explain the large PC71BM:X2 composition range where good performance is observed [1]. The talk will also show that spin cast CH3NH3PbI3 films consistent of both crystalline and amorphous regions, which can explain previous heterogeneity in the PL imaging [2]. [1] Huang et al., Adv. Energy Mater. 4, 1301886 (2014). [2] deQuilettes et al., Science 348, 683 (2015).

  2. Photothermal response of near-infrared-absorbing NanoGUMBOS.

    PubMed

    Dumke, Jonathan C; Qureshi, Ammar; Hamdan, Suzana; El-Zahab, Bilal; Das, Susmita; Hayes, Daniel J; Boldor, Dorin; Rupnik, Kresimir; Warner, Isiah M

    2014-01-01

    The photothermal properties of several near-infrared-absorbing nanoparticles derived from group of uniform materials based on organic salts (GUMBOS) and composed of cationic dyes coupled with biocompatible anions are evaluated. These nanoparticles were synthesized using a reprecipitation method performed at various pH values: 2.0, 5.0, 7.0, 9.0, and 11.0. The cations for the nanoparticles derived from GUMBOS (nanoGUMBOS), [1048] and [1061], have absorbance maxima at wavelengths overlapping with human soft tissue absorbance minima. Near-infrared-absorbing nanoGUMBOS excited with a 1064 nm continuous laser led to heat generation, with an average temperature increase of 20.4 ± 2.7 °C. Although the [1061][Deoxycholate] nanoGUMBOS generated the highest temperature increase (23.7 ± 2.4 °C), it was the least photothermally efficient compound (13.0%) due to its relatively large energy band gap of 0.892 eV. The more photothermally efficient compound [1048][Ascorbate] (64.4%) had a smaller energy band gap of 0.861 eV and provided an average photothermal temperature increase of 21.0 ± 2.1 °C.

  3. The nature of intermediate-redshift damped Lyα absorbers.

    NASA Astrophysics Data System (ADS)

    Le Brun, V.; Bergeron, J.; Boisse, P.; Deharveng, J. M.

    1997-05-01

    We present HST/WFPC2 high-spatial resolution images in the R and B bands of the close environment of the sightlines to seven quasars which spectra show either a damped Lyα absorption line, 21cm absorption, or a very strong MgII/FeII absorption system at intermediate redshifts (0.4<=z<=1). Objects down to about 0.3", or 2.0kpc at z=0.6 (H_0_=50km/s/Mpc, q_0_=0), and to a limiting magnitude m_702, lim_=25.9 could be detected for seven fields comprising eight absorbers (one at higher redshift z=1.78 towards MC 1331+170) with high Hi column densities of at least 1x10^20^cm^-2^. In each case, a candidate absorber with absolute magnitude M_B_=~-19.0 or much brighter has been detected. This small sample of gas-rich galaxies at intermediate redshifts covers a wide range in morphological types. There are three spiral galaxies of various sizes and luminosities (towards 3C 196, Q 1209+107 and MC 1331+170), three compact objects (towards EX 0302-223, PKS 0454+039 and, at high redshift, MC 1331+170), and two amorphous, low surface brightness galaxies (towards PKS 1229-021 and 3C 286). In the fields around 3C 196, PKS 1229-021 and Q 1209+107, there is an excess of galaxies in the PC2 images, suggestive of the presence of a group of galaxies associated with the damped Lyα absorber, or maybe with the quasar itself for the two z_e_<=1.0 cases. For 3C 196 and 3C 286, the quasar host galaxies have also tentatively been discovered. We do not detect any quasar multiple images, implying no large amount of dark matter around the damped Lyα absorbers. This survey also led to the discovery of the first z=~1.0 optical counterpart of a quasar radio jet (PKS 1229-021). As will be reported elsewhere (Boisse et al. 1996), spectroscopy with the HST-FOS of the strong MgII/FeII absorption systems confirms the validity of our selection criterion in predicting the existence of damped Lyα systems.

  4. Design of a nonlinear torsional vibration absorber

    NASA Astrophysics Data System (ADS)

    Tahir, Ammaar Bin

    Tuned mass dampers (TMD) utilizing linear spring mechanisms to mitigate destructive vibrations are commonly used in practice. A TMD is usually tuned for a specific resonant frequency or an operating frequency of a system. Recently, nonlinear vibration absorbers attracted attention of researchers due to some potential advantages they possess over the TMDs. The nonlinear vibration absorber, or the nonlinear energy sink (NES), has an advantage of being effective over a broad range of excitation frequencies, which makes it more suitable for systems with several resonant frequencies, or for a system with varying excitation frequency. Vibration dissipation mechanism in an NES is passive and ensures that there is no energy backflow to the primary system. In this study, an experimental setup of a rotational system has been designed for validation of the concept of nonlinear torsional vibration absorber with geometrically induced cubic stiffness nonlinearity. Dimensions of the primary system have been optimized so as to get the first natural frequency of the system to be fairly low. This was done in order to excite the dynamic system for torsional vibration response by the available motor. Experiments have been performed to obtain the modal parameters of the system. Based on the obtained modal parameters, the design optimization of the nonlinear torsional vibration absorber was carried out using an equivalent 2-DOF modal model. The optimality criterion was chosen to be maximization of energy dissipation in the nonlinear absorber attached to the equivalent 2-DOF system. The optimized design parameters of the nonlinear absorber were tested on the original 5-DOF system numerically. A comparison was made between the performance of linear and nonlinear absorbers using the numerical models. The comparison showed the superiority of the nonlinear absorber over its linear counterpart for the given set of primary system parameters as the vibration energy dissipation in the former is

  5. 45 CFR 32.8 - Amounts withheld.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... paragraph (b) of this section. The employer may use the SF-329C “Wage Garnishment Worksheet” to calculate... garnishment order up to 15% of the debtor's disposable pay; or (2) The amount set forth in 15 U.S.C. 1673(a)(2) (Maximum allowable garnishment). The amount set forth at 15 U.S.C. 1673(a)(2) is the amount by which...

  6. 45 CFR 32.8 - Amounts withheld.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... paragraph (b) of this section. The employer may use the SF-329C “Wage Garnishment Worksheet” to calculate... garnishment order up to 15% of the debtor's disposable pay; or (2) The amount set forth in 15 U.S.C. 1673(a)(2) (Maximum allowable garnishment). The amount set forth at 15 U.S.C. 1673(a)(2) is the amount by which...

  7. The Extended High A(V) Quasar Survey: Searching for Dusty Absorbers toward Mid-infrared-selected Quasars

    NASA Astrophysics Data System (ADS)

    Krogager, J.-K.; Fynbo, J. P. U.; Heintz, K. E.; Geier, S.; Ledoux, C.; Møller, P.; Noterdaeme, P.; Venemans, B. P.; Vestergaard, M.

    2016-11-01

    We present the results of a new spectroscopic survey for dusty intervening absorption systems, particularly damped Lyα absorbers (DLAs), toward reddened quasars. The candidate quasars are selected from mid-infrared photometry from the Wide-field Infrared Survey Explorer combined with optical and near-infrared photometry. Out of 1073 candidates, we secure low-resolution spectra for 108 using the Nordic Optical Telescope on La Palma, Spain. Based on the spectra, we are able to classify 100 of the 108 targets as quasars. A large fraction (50%) is observed to have broad absorption lines (BALs). Moreover, we find six quasars with strange breaks in their spectra, which are not consistent with regular dust reddening. Using template fitting, we infer the amount of reddening along each line of sight ranging from A(V) ≈ 0.1 to 1.2 mag (assuming a Small Magellanic Cloud extinction curve). In four cases, the reddening is consistent with dust exhibiting the 2175 Å feature caused by an intervening absorber, and for two of these, an Mg ii absorption system is observed at the best-fit absorption redshift. In the rest of the cases, the reddening is most likely intrinsic to the quasar. We observe no evidence for dusty DLAs in this survey. However, the large fraction of BAL quasars hampers the detection of absorption systems. Out of the 50 non-BAL quasars, only 28 have sufficiently high redshift to detect Lyα in absorption.

  8. Ultrathin and lightweight microwave absorbers made of mu-near-zero metamaterials

    PubMed Central

    Zhong, Shuomin; He, Sailing

    2013-01-01

    We present a theory of perfect absorption in a bilayer model composed of a mu-near-zero (MNZ) metamaterial (MM) absorbing layer on a metallic substrate. Our analytical solutions reveal that a MM layer with a large purely imaginary permeability and a moderate permittivity backed by a metallic plane has a zero reflection at normal incidence when the thickness is ultrathin. The impedance-mismatched metamaterial absorber (MA) can be 77.3% thinner than conventional impedance-matched MAs with the same material loss in order to get the same absorption. A microwave absorber using double-layered spiral MMs with a thickness of only about one percent of the operating wavelength is designed and realized. An absorption efficiency above 93% at 1.74 GHz is demonstrated experimentally at illumination angles up to 60 degrees. Our absorber is 98% lighter than traditional microwave absorbers made of natural materials working at the same frequencies. PMID:23803861

  9. Freshwater DOM quantity and quality from a two-component model of UV absorbance

    USGS Publications Warehouse

    Carter, Heather T.; Tipping, Edward; Koprivnjak, Jean-Francois; Miller, Matthew P.; Cookson, Brenda; Hamilton-Taylor, John

    2012-01-01

    We present a model that considers UV-absorbing dissolved organic matter (DOM) to consist of two components (A and B), each with a distinct and constant spectrum. Component A absorbs UV light strongly, and is therefore presumed to possess aromatic chromophores and hydrophobic character, whereas B absorbs weakly and can be assumed hydrophilic. We parameterised the model with dissolved organic carbon concentrations [DOC] and corresponding UV spectra for c. 1700 filtered surface water samples from North America and the United Kingdom, by optimising extinction coefficients for A and B, together with a small constant concentration of non-absorbing DOM (0.80 mg DOC L-1). Good unbiased predictions of [DOC] from absorbance data at 270 and 350 nm were obtained (r2 = 0.98), the sum of squared residuals in [DOC] being reduced by 66% compared to a regression model fitted to absorbance at 270 nm alone. The parameterised model can use measured optical absorbance values at any pair of suitable wavelengths to calculate both [DOC] and the relative amounts of A and B in a water sample, i.e. measures of quantity and quality. Blind prediction of [DOC] was satisfactory for 9 of 11 independent data sets (181 of 213 individual samples).

  10. Direct absorbed dose to water determination based on water calorimetry in scanning proton beam delivery

    SciTech Connect

    Sarfehnia, A.; Clasie, B.; Chung, E.; Lu, H. M.; Flanz, J.; Cascio, E.; Engelsman, M.; Paganetti, H.; Seuntjens, J.

    2010-07-15

    Purpose: The aim of this manuscript is to describe the direct measurement of absolute absorbed dose to water in a scanned proton radiotherapy beam using a water calorimeter primary standard. Methods: The McGill water calorimeter, which has been validated in photon and electron beams as well as in HDR {sup 192}Ir brachytherapy, was used to measure the absorbed dose to water in double scattering and scanning proton irradiations. The measurements were made at the Massachusetts General Hospital proton radiotherapy facility. The correction factors in water calorimetry were numerically calculated and various parameters affecting their magnitude and uncertainty were studied. The absorbed dose to water was compared to that obtained using an Exradin T1 Chamber based on the IAEA TRS-398 protocol. Results: The overall 1-sigma uncertainty on absorbed dose to water amounts to 0.4% and 0.6% in scattered and scanned proton water calorimetry, respectively. This compares to an overall uncertainty of 1.9% for currently accepted IAEA TRS-398 reference absorbed dose measurement protocol. The absorbed dose from water calorimetry agrees with the results from TRS-398 well to within 1-sigma uncertainty. Conclusions: This work demonstrates that a primary absorbed dose standard based on water calorimetry is feasible in scattered and scanned proton beams.

  11. The nonlinear piezoelectric tuned vibration absorber

    NASA Astrophysics Data System (ADS)

    Soltani, P.; Kerschen, G.

    2015-07-01

    This paper proposes a piezoelectric vibration absorber, termed the nonlinear piezoelectric tuned vibration absorber (NPTVA), for the mitigation of nonlinear resonances of mechanical systems. The new feature of the NPTVA is that its nonlinear restoring force is designed according to a principle of similarity, i.e., the NPTVA should be an electrical analog of the nonlinear host system. Analytical formulas for the NPTVA parameters are derived using the homotopy perturbation method. Doing so, a nonlinear generalization of Den Hartog’s equal-peak tuning rule is developed for piezoelectric vibration absorbers.

  12. Sleep and Delinquency: Does the Amount of Sleep Matter?

    ERIC Educational Resources Information Center

    Clinkinbeard, Samantha S.; Simi, Pete; Evans, Mary K.; Anderson, Amy L.

    2011-01-01

    Sleep, a key indicator of health, has been linked to a variety of indicators of well-being such that people who get an adequate amount generally experience greater well-being. Further, a lack of sleep has been linked to a wide range of negative developmental outcomes, yet sleep has been largely overlooked among researchers interested in adolescent…

  13. 20 CFR 617.34 - Amount.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... the Federal travel regulations (see 41 CFR part 101-7) for the locality where the job search is... WORKERS UNDER THE TRADE ACT OF 1974 Job Search Allowances § 617.34 Amount. (a) Computation. The amount of a job search allowance shall be 90 percent of the total costs of each of the following...

  14. 20 CFR 617.34 - Amount.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... the Federal travel regulations (see 41 CFR part 101-7) for the locality where the job search is... WORKERS UNDER THE TRADE ACT OF 1974 Job Search Allowances § 617.34 Amount. (a) Computation. The amount of a job search allowance shall be 90 percent of the total costs of each of the following...

  15. 20 CFR 617.34 - Amount.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... the Federal travel regulations (see 41 CFR part 101-7) for the locality where the job search is... WORKERS UNDER THE TRADE ACT OF 1974 Job Search Allowances § 617.34 Amount. (a) Computation. The amount of a job search allowance shall be 90 percent of the total costs of each of the following...

  16. 46 CFR 308.403 - Insured amounts.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... total amount of war risk insurance obtainable from companies authorized to do an insurance business in a... authorized to do an insurance business in a State of the United States. (c) Maximum liability. The amount of... MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War...

  17. 46 CFR 308.403 - Insured amounts.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... total amount of war risk insurance obtainable from companies authorized to do an insurance business in a... authorized to do an insurance business in a State of the United States. (c) Maximum liability. The amount of... MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War...

  18. 20 CFR 617.34 - Amount.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... WORKERS UNDER THE TRADE ACT OF 1974 Job Search Allowances § 617.34 Amount. (a) Computation. The amount of a job search allowance shall be 90 percent of the total costs of each of the following allowable... job search; or (ii) The cost per mile at the prevailing mileage rate authorized under the...

  19. 46 CFR 308.100 - Insured amount.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Hull and Disbursements Insurance § 308.100 Insured amount. An applicant for war risk hull insurance shall state the amount of insurance desired but any payment of claim for damage to or actual or...

  20. 23 CFR 1335.8 - Grant amounts.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Grant amounts. 1335.8 Section 1335.8 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STATE HIGHWAY SAFETY DATA IMPROVEMENTS § 1335.8 Grant amounts. (a) Start-up grant. A State that qualifies for a start-up grant under §...

  1. 23 CFR 1335.8 - Grant amounts.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 23 Highways 1 2011-04-01 2011-04-01 false Grant amounts. 1335.8 Section 1335.8 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STATE HIGHWAY SAFETY DATA IMPROVEMENTS § 1335.8 Grant amounts. (a) Start-up grant. A State that qualifies for a start-up grant under §...

  2. 13 CFR 400.202 - Loan amount.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ....202 Business Credit and Assistance EMERGENCY STEEL GUARANTEE LOAN BOARD EMERGENCY STEEL GUARANTEE LOAN PROGRAM Steel Guarantee Loans § 400.202 Loan amount. (a) The aggregate amount of loan principal guaranteed under this Program to a single Qualified Steel Company may not exceed $ 250 million. (b) Of...

  3. 13 CFR 400.202 - Loan amount.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ....202 Business Credit and Assistance EMERGENCY STEEL GUARANTEE LOAN BOARD EMERGENCY STEEL GUARANTEE LOAN PROGRAM Steel Guarantee Loans § 400.202 Loan amount. (a) The aggregate amount of loan principal guaranteed under this Program to a single Qualified Steel Company may not exceed $ 250 million. (b) Of...

  4. 13 CFR 400.202 - Loan amount.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ....202 Business Credit and Assistance EMERGENCY STEEL GUARANTEE LOAN BOARD EMERGENCY STEEL GUARANTEE LOAN PROGRAM Steel Guarantee Loans § 400.202 Loan amount. (a) The aggregate amount of loan principal guaranteed under this Program to a single Qualified Steel Company may not exceed $ 250 million. (b) Of...

  5. 13 CFR 400.202 - Loan amount.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ....202 Business Credit and Assistance EMERGENCY STEEL GUARANTEE LOAN BOARD EMERGENCY STEEL GUARANTEE LOAN PROGRAM Steel Guarantee Loans § 400.202 Loan amount. (a) The aggregate amount of loan principal guaranteed under this Program to a single Qualified Steel Company may not exceed $ 250 million. (b) Of...

  6. 13 CFR 400.202 - Loan amount.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ....202 Business Credit and Assistance EMERGENCY STEEL GUARANTEE LOAN BOARD EMERGENCY STEEL GUARANTEE LOAN PROGRAM Steel Guarantee Loans § 400.202 Loan amount. (a) The aggregate amount of loan principal guaranteed under this Program to a single Qualified Steel Company may not exceed $ 250 million. (b) Of...

  7. 78 FR 59702 - Medicare Program; Medicare Appeals: Adjustment to the Amount in Controversy Threshold Amounts for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-27

    ...This notice announces the annual adjustment in the amount in controversy (AIC) threshold amounts for Administrative Law Judge (ALJ) hearings and judicial review under the Medicare appeals process. The adjustment to the AIC threshold amounts will be effective for requests for ALJ hearings and judicial review filed on or after January 1, 2014. The calendar year 2014 AIC threshold amounts are......

  8. Wideband long wave infrared metamaterial absorbers based on silicon nitride

    NASA Astrophysics Data System (ADS)

    Üstün, Kadir; Turhan-Sayan, Gönül

    2016-11-01

    In this paper, we present silicon nitride metamaterial absorber designs that accomplish large bandwidth and high absorption in the long wave infrared (LWIR) region. These designs are based on the metal-insulator-metal topology, insulator (silicon nitride), and the top metal (aluminum) layers are optimized to obtain high absorptance values in large bandwidths, for three different silicon nitride based absorber structures. The absorption spectrum of the final design reaches absorptance values above 90% in the wavelength interval between 8.07 μm and 11.97 μm, and above 80% in the wavelength interval between 7.9 μm and 14 μm, in the case of normal incidence. The difficulty in the design process of such absorbers stems from the highly dispersive behavior of silicon nitride in the LWIR region. On the other hand, silicon nitride is a widely used material in microbolometers, and accomplishing wide band absorption in silicon nitride is crucial in this regard. Therefore, this study will pave the way for more efficient infrared imaging devices, which are crucial for defense and security systems. Additionally, such designs may also find applications in thermal emitters.

  9. Graphene-enabled electrically switchable radar absorbing surfaces

    NASA Astrophysics Data System (ADS)

    Balci, Osman; Polat, Emre Ozan; Kakenov, Nurbek; Kocabas, Coskun

    2015-03-01

    Radar absorbing materials are used in stealth technologies for concealment of an object from radar detection. Resistive and/or magnetic composite materials are used to reduce the backscattered microwave signals. Inability to control electrical properties of these materials however, hinders the realization of active camouflage systems which require adaptive surfaces operating in microwave frequencies. Here, using large-area graphene electrodes, we demonstrate a new class of active surfaces which enables unprecedented ability to control reflection, transmission and absorption of microwaves by electrical means. Instead of tuning bulk material property, our strategy relies on electrostatic tuning of the charge density on an atomically thin electrode which operates as a tunable metal in microwave frequencies. Notably, we fabricated large area adaptive radar absorbing surfaces with tunable reflection suppression ratio up to 50 dB with operation voltages less than 5 V. These electrically switchable radar absorbing surfaces provide a significant step in realization of active camouflage systems and adaptive cloaking in microwave frequencies, which cannot be realized by conventional materials.

  10. Self-assembly of highly efficient, broadband plasmonic absorbers for solar steam generation

    PubMed Central

    Zhou, Lin; Tan, Yingling; Ji, Dengxin; Zhu, Bin; Zhang, Pei; Xu, Jun; Gan, Qiaoqiang; Yu, Zongfu; Zhu, Jia

    2016-01-01

    The study of ideal absorbers, which can efficiently absorb light over a broad range of wavelengths, is of fundamental importance, as well as critical for many applications from solar steam generation and thermophotovoltaics to light/thermal detectors. As a result of recent advances in plasmonics, plasmonic absorbers have attracted a lot of attention. However, the performance and scalability of these absorbers, predominantly fabricated by the top-down approach, need to be further improved to enable widespread applications. We report a plasmonic absorber which can enable an average measured absorbance of ~99% across the wavelengths from 400 nm to 10 μm, the most efficient and broadband plasmonic absorber reported to date. The absorber is fabricated through self-assembly of metallic nanoparticles onto a nanoporous template by a one-step deposition process. Because of its efficient light absorption, strong field enhancement, and porous structures, which together enable not only efficient solar absorption but also significant local heating and continuous stream flow, plasmonic absorber–based solar steam generation has over 90% efficiency under solar irradiation of only 4-sun intensity (4 kW m−2). The pronounced light absorption effect coupled with the high-throughput self-assembly process could lead toward large-scale manufacturing of other nanophotonic structures and devices. PMID:27152335

  11. Attenuation of external Bremsstrahlung in metallic absorbers

    SciTech Connect

    Dhaliwal, A.S.; Powar, M.S.; Singh, M. )

    1990-12-01

    In this paper attenuation of bremsstrahlung from {sup 147}Pm and {sup 170}Tm beta emitters has been studied in aluminum, copper, tin, and lead metallic absorbers. Bremsstrahlung spectra and mass attenuation coefficients for monoenergetic gamma rays are used to calculate theoretical attenuation curves. Magnetic deflection and beta stopping techniques are used to measure the integral bremsstrahlung intensities above 30 keV in different target thicknesses. Comparison of measured and calculated attenuation curves shows a good agreement for various absorbers, thus providing a test of this technique, which may be useful in understanding bremsstrahlung intensity buildup and in the design of optimum shielding for bremsstrahlung sources. It is found that the absorption of bremsstrahlung in metallic absorbers does not obey an exponential law and that absorbers act as energy filters.

  12. Energy absorber uses expanded coiled tube

    NASA Technical Reports Server (NTRS)

    Johnson, E. F.

    1972-01-01

    Mechanical shock mitigating device, based on working material to its failure point, absorbs mechanical energy by bending or twisting tubing. It functions under axial or tangential loading, has no rebound, is area independent, and is easy and inexpensive to build.

  13. Neutron absorbing coating for nuclear criticality control

    DOEpatents

    Mizia, Ronald E.; Wright, Richard N.; Swank, William D.; Lister, Tedd E.; Pinhero, Patrick J.

    2007-10-23

    A neutron absorbing coating for use on a substrate, and which provides nuclear criticality control is described and which includes a nickel, chromium, molybdenum, and gadolinium alloy having less than about 5% boron, by weight.

  14. Absorbed dose from traversing spherically symmetric, Gaussian radioactive clouds

    SciTech Connect

    Thompson, J.M. ); Poston, J.W. . Dept. of Nuclear Engineering)

    1999-06-01

    If a large radioactive cloud is produced, sampling may require that an airplane traverse the cloud. A method to predict the absorbed dose to the aircrew from penetrating the radioactive cloud is needed. Dose rates throughout spherically symmetric Gaussian clouds of various sizes, and the absorbed doses from traversing the clouds, were calculated. Cloud size is a dominant parameter causing dose to vary by orders of magnitude for a given dose rate measured at some distance. A method to determine cloud size, based on dose rate readings at two or more distances from the cloud center, was developed. This method, however, failed to resolve the smallest cloud sizes from measurements made at 1,000 m to 2,000 m from the cloud center.

  15. A Robust Absorbing Boundary Condition for Compressible Flows

    NASA Technical Reports Server (NTRS)

    Loh, Ching Y.; orgenson, Philip C. E.

    2005-01-01

    An absorbing non-reflecting boundary condition (NRBC) for practical computations in fluid dynamics and aeroacoustics is presented with theoretical proof. This paper is a continuation and improvement of a previous paper by the author. The absorbing NRBC technique is based on a first principle of non reflecting, which contains the essential physics that a plane wave solution of the Euler equations remains intact across the boundary. The technique is theoretically shown to work for a large class of finite volume approaches. When combined with the hyperbolic conservation laws, the NRBC is simple, robust and truly multi-dimensional; no additional implementation is needed except the prescribed physical boundary conditions. Several numerical examples in multi-dimensional spaces using two different finite volume schemes are illustrated to demonstrate its robustness in practical computations. Limitations and remedies of the technique are also discussed.

  16. Porous absorber for solar air heaters

    SciTech Connect

    Finch, J.A.

    1980-09-10

    A general discussion of the factors affecting solar collector performance is presented. Bench scale tests done to try to determine the heat transfer characteristics of various screen materials are explained. The design, performance, and evaluation of a crude collector with a simple screen stack absorber is treated. The more sophisticated absorber concept, and its first experimental approximation is examined. A short summary of future plans for the collector concept is included. (MHR)

  17. Multilayer Radar Absorbing Non-Woven Material

    NASA Astrophysics Data System (ADS)

    Dedov, A. V.; Nazarov, V. G.

    2016-06-01

    We study the electrical properties of multilayer radar absorbing materials obtained by adding nonwoven sheets of dielectric fibers with an intermediate layer of electrically conductive carbon fibers. Multilayer materials that absorb electromagnetic radiation in a wide frequency range are obtained by varying the content of the carbon fibers. The carbon-fiber content dependent mechanism of absorption of electromagnetic radiation by sheets and multilayer materials is considered.

  18. Non-absorbed Antibiotics for IBS

    DTIC Science & Technology

    2012-03-16

    absorbed antibiotic rifaximin for nonconstipated irritable bowel syndrome (IBS). This effort adds to the body of literature from other, smaller studies that...have demonstrated clinical efficacy for IBS with rifaximin . Non-absorbed antibiotics have been endorsed by the American College of Gastroenterology... rifaximin 400 mg three times daily for 10 days or placebo. During the initial 2 weeks of therapy and the subsequent 10 weeks of follow-up rifaximin

  19. Structured metal film as a perfect absorber.

    PubMed

    Xiong, Xiang; Jiang, Shang-Chi; Hu, Yu-Hui; Peng, Ru-Wen; Wang, Mu

    2013-08-07

    A new type of absorber, a four-tined fish-spear-like resonator (FFR), constructed by the two-photon polymerization process, is reported. An absorbance of more than 90% is experimentally realized and the resonance occurs in the space between the tines. Since a continuous layer of metallic thin film covers the structure, it is perfectly thermo- and electroconductive, which is the mostly desired feature for many applications.

  20. Identification of QTL affecting a piglet’s ability to acquire and absorb gamma-immunoglobulin from colostrum

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Consumption of an adequate amount of colostrum is critical to a piglet’s survival and productivity. The immunocrit is an inexpensive rapid measurement of the amount of gamma-immunoglobulin absorbed by a piglet. Genetic analysis of immunocrits on 5,312 piglets indicated that the heritabilities (se) f...

  1. Radar Absorbing Materials for Cube Stealth Satellite

    NASA Astrophysics Data System (ADS)

    Micheli, D.; Pastore, R.; Vricella, A.; Marchetti, M.

    A Cube Stealth Satellite is proposed for potential applications in defense system. Particularly, the faces of the satellite exposed to the Earth are made of nanostructured materials able to absorb radar surveillance electromagnetic waves, conferring stealth capability to the cube satellite. Microwave absorbing and shielding material tiles are proposed using composite materials consisting in epoxy-resin and carbon nanotubes filler. The electric permittivity of the composite nanostructured materials is measured and discussed. Such data are used by the modeling algorithm to design the microwave absorbing and the shielding faces of the cube satellite. The electromagnetic modeling takes into account for several incidence angles (0-80°), extended frequency band (2-18 GHz), and for the minimization of the electromagnetic reflection coefficient. The evolutionary algorithm used for microwave layered microwave absorber modeling is the recently developed Winning Particle Optimization. The mathematical model of the absorbing structure is finally experimentally validated by comparing the electromagnetic simulation to the measurement of the manufactured radar absorber tile. Nanostructured composite materials manufacturing process and electromagnetic reflection measurements methods are described. Finally, a finite element method analysis of the electromagnetic scattering by cube stealth satellite is performed.

  2. Absorbance changes of carotenoids in different solvents.

    PubMed

    Zang, L Y; Sommerburg, O; van Kuijk, F J

    1997-01-01

    Carotenoids are typically measured in tissues with the high performance liquid chromatography (HPLC) and quantitation is usually done by calibrating with stock solutions in solvents. Four carotenoids including lutein, zeaxanthin, lycopene and beta-carotene were dissolved in hexane and methanol respectively, and their absorbance characteristics were compared. Lutein shows absorbance spectra that are almost independent of solvents at various concentrations. Spectra of zeaxanthin, lycopene and beta-carotene were found to be more solvent-dependent. The absorbance of zeaxanthin at lambda max is about approximately 2 times larger in methanol than in hexane at the higher concentrations, and increased non-linearly with increasing concentration in hexane. The absorbance of lycopene at lambda max in hexane is approximately 4 fold larger than in methanol, but the absorbance of the methanol sample can be recovered by re-extracting this sample in hexane. The absorbance of beta-carotene in hexane is larger than in methanol, and increased linearly with increasing concentration. But beta-carotene showed a non-linear concentration effect in methanol. There are very small variations in lambda max for all four carotenoids between hexane and methanol, due to differences in molar extinction coefficients. The non-linear concentration effects for these carotenoids are probably due to differences in solubility leading to the formation of microcrystals. Thus, care should be taken with quantitation of tissue carotenoid values, when they depend on measurement of concentrations in stock solutions.

  3. Perfect terahertz absorber using fishnet based metafilm

    SciTech Connect

    Azad, Abul Kalam; Shchegolkov, Dmitry Yu; Chen, Houtong; Taylor, Antoinette; Smirnova, E I; O' Hara, John F

    2009-01-01

    We present a perfect terahertz (THz) absorber working for a broad-angle of incidence. The two fold symmetry of rectangular fishnet structure allows either complete absorption or mirror like reflection depending on the polarization of incident the THz beam. Metamaterials enable the ability to control the electromagnetic wave in a unique fashion by designing the permittivity or permeability of composite materials with desired values. Although the initial idea of metamaterials was to obtain a negative index medium, however, the evolution of metamaterials (MMs) offers a variety of practically applicable devices for controlling electromagnetic wave such as tunable filters, modulators, phase shifters, compact antenna, absorbers, etc. Terahertz regime, a crucial domain of the electromagnetic wave, is suffering from the scarcity of the efficient devices and might take the advantage of metamaterials. Here, we demonstrate design, fabrication, and characterization of a terahertz absorber based on a simple fishnet metallic film separated from a ground mirror plane by a dielectric spacer. Such absorbers are in particular important for bolometric terahertz detectors, high sensitivity imaging, and terahertz anechoic chambers. Recently, split-ring-resonators (SRR) have been employed for metamaterial-based absorbers at microwave and THz frequencies. The experimental demonstration reveals that such absorbers have absorptivity close to unity at resonance frequencies. However, the downside of these designs is that they all employ resonators of rather complicated shape with many fine parts and so they are not easy to fabricate and are sensitive to distortions.

  4. Are sea-ice driven increases of absorbed solar radiation in the Arctic offset by increasing sea ice extent in the Antarctic?: A bipolar comparison of satellite-derived estimates of absorbed solar radiation and sea ice area

    NASA Astrophysics Data System (ADS)

    Meier, W.; Ahlert, A.; Loeb, N. G.; Stewart, S.

    2015-12-01

    Due to its high surface albedo, sea ice reflects a substantial amount of incoming solar radiation relative to an ice-free ocean surface. Thus the presence of sea ice results in less absorption of energy during the long days of the polar summers. AS expected, the dramatic decline in Arctic summer sea ice area over the past decades has been accompanied by an increase in absorbed solar radiation (ASR). This has been observed by in situ measurements as well as satellite observations. The Clouds and Earth's Radiant Energy System (CERES) instrument on the NASA EOS Terra platform has provided global coverage of solar radiation since late 1999, providing a large-scale indicator of changes in absorbed solar radiation. These data show that the dramatic decrease in Arctic summer sea ice has been accompanied an increase in absorbed solar radiation during the boreal summer, with the largest gains corresponding to regions of the most notable summer ice loss. While overall there is good correlation, the relationship is far from perfect. This is not unexpected since other factors - particularly clouds - play a role in the amount of ASR. In contrast to the decreasing sea ice in the Arctic, the Antarctic has seen a trend of increasing coverage. The increases are smaller, in both absolute and relative terms. However, the southern hemisphere sea ice cover is at a higher average latitude than in the north due to the presence of the Antarctic continent and is thus is potentially exposed to higher incoming solar radiation. Here we investigate the relationship between changes in sea ice and changes in ASR (estimated from CERES data) in the Arctic and Antarctic during their respective summer seasons. To first order, both hemispheres show an expected relationship between sea ice and absorbed solar radiation in the Arctic (sea ice decrease, ASR increase) and the Antarctic (sea ice increase, ASR decrease). However, the correlation in the Antarctic is not nearly as clear in the Arctic and the

  5. 12 CFR 313.95 - Amounts withheld.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... CORPORATE DEBT COLLECTION Administrative Wage Garnishment § 313.95 Amounts withheld. (a) Upon receipt of the... orders with priority, the following shall apply: (1) Unless otherwise provided by federal...

  6. 23 CFR 1335.8 - Grant amounts.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 23 Highways 1 2012-04-01 2012-04-01 false Grant amounts. 1335.8 Section 1335.8 Highways NATIONAL... § 1335.8 Grant amounts. (a) Start-up grant. A State that qualifies for a start-up grant under § 1335.7(a) of this part shall be eligible to receive $25,000. (b) Initiation grant. A State that qualifies...

  7. Unusual amount of (-)-mesquitol from the heartwood of Prosopis juliflora.

    PubMed

    Sirmah, Peter; Dumarçay, Stéphane; Masson, Eric; Gérardin, Philippe

    2009-01-01

    A large amount of flavonoid has been extracted and isolated from the heartwood of Prosopis juliflora, an exogenous wood species of Kenya. Structural and physicochemical elucidation based on FTIR, (1)H and (13)C NMR, GC-MS and HPLC analysis clearly demonstrated the presence of (-)-mesquitol as the sole compound without any noticeable impurities. The product was able to slow down oxidation of methyl linoleate induced by AIBN. The important amount and high purity of (-)-mesquitol present in the acetonic extract of P. juliflora could therefore be of valuable interest as a potential source of antioxidants from a renewable origin.

  8. On the efficacy of an active absorber with internal state feedback for controlling self-excited oscillations

    NASA Astrophysics Data System (ADS)

    Chatterjee, S.

    2011-03-01

    An active absorber, utilizing the state feedback of the absorber mass, is proposed for controlling the self-excited vibration of a single degree-of-freedom extended Rayleigh oscillator. The control strategy renders the design standalone. The process of optimizing the control gains is discussed. The analysis reveals that by selecting a suitably high value of the absorber frequency, the overall damping of the system can be made as high as the critical damping irrespective of the amount of negative linear damping present in the primary self-excited system. It is shown that a higher value of the absorber frequency is profitable in almost all respects related to the performance as well as the robustness of the system under parametric uncertainty. The nonlinear analysis of the system reveals that the proposed absorber can control the amplitude of oscillation even in case detuning (up to some limit) of the absorber frequency from its nominal value. The region of global stability increases with the increase in the value of the absorber frequency. However some aspects, like higher absorber deflection, reduced lower bound of the admissible detuning and the lower range of the tolerance on the mass ratio limit using a very high value of absorber frequency. The results of numerical simulations confirm the analytical results.

  9. Metal Hydrides as hot carrier cell absorber materials

    NASA Astrophysics Data System (ADS)

    Wang, Pei; Wen, Xiaoming; Shrestha, Santosh; Conibeer, Gavin; Aguey-Zinsou, Kondo-Francois

    2016-09-01

    The hot Carrier Solar Cell (HCSC) allows the photon-induced hot carriers (the carriers with energy larger than the band gap) to be collected before they completely thermalise. The absorber of the HCSC should have a large phononic band gap to supress Klemens Decay, which results in a slow carrier cooling speed. In fact, a large phononic band gap likely exists in a binary compound whose constituent elements have a large mass ratio between each other. Binary hydrides with their overwhelming mass ratio of the constituent elements are important absorber candidates. Study on different types of binary hydrides as potential absorber candidates is presented in this paper. Many binary transition metal hydrides have reported theoretical or experimental phonon dispersion charts which show large phononic band gaps. Among these hydrides, the titanium hydride (TiHX) is outstanding because of its low cost, easy fabrication process and is relatively inert to air and water. A TiHX thin film is fabricated by directly hydrogenating an evaporated titanium thin film. Characterisation shows good crystal quality and the hydrogenation process is believed to be successful. Ultrafast transient absorption (TA) spectroscopy is used to study the electron cooling time of TiHX. The result is very noisy due to the low absorption and transmission of the sample. The evolution of the TA curves has been explained by band to band transition using the calculated band structure of TiH2. Though not reliable due to the high noise, decay time fitting at 700nm and 600nm shows a considerably slow carrier cooling speed of the sample.

  10. Absorbing aerosols over Asia: A Geophysical Fluid Dynamics Laboratory general circulation model sensitivity study of model response to aerosol optical depth and aerosol absorption

    NASA Astrophysics Data System (ADS)

    Randles, C. A.; Ramaswamy, V.

    2008-11-01

    Forcing by absorbing atmospheric black carbon (BC) tends to heat the atmosphere, cool the surface, and reduce the surface latent and sensible heat fluxes. BC aerosol can have a large impact on regional climates and the hydrologic cycle. However, significant uncertainties remain concerning the increases in (1) the total amount of all aerosol species and (2) the amount of aerosol absorption that may have occurred over the 1950-1990 period. Focusing on south and east Asia, the sensitivity of a general circulation model's climate response (with prescribed sea surface temperatures and aerosol distributions) to such changes is investigated by considering a range of both aerosol absorption and aerosol extinction optical depth increases. We include direct and semidirect aerosol effects only. Precipitation changes are less sensitive to changes in aerosol absorption optical depth at lower aerosol loadings. At higher-extinction optical depths, low-level convergence and increases in vertical velocity overcome the stabilizing effects of absorbing aerosols and enhance the monsoonal circulation and precipitation in northwestern India. In contrast, the presence of increases in only scattering aerosols weakens the monsoonal circulation and inhibits precipitation here. Cloud amount changes can enhance or counteract surface solar flux reduction depending on the aerosol loading and absorption, with the changes also influencing the surface temperature and the surface energy balance. The results have implications for aerosol reduction strategies in the future that seek to mitigate air pollution concerns. At higher optical depths, if absorbing aerosol is present, reduction of scattering aerosol alone has a reduced effect on precipitation changes, implying that reductions in BC aerosols should be undertaken at the same time as reductions in sulfate aerosols.

  11. Method of absorbance correction in a spectroscopic heating value sensor

    SciTech Connect

    Saveliev, Alexei; Jangale, Vilas Vyankatrao; Zelepouga, Sergeui; Pratapas, John

    2013-09-17

    A method and apparatus for absorbance correction in a spectroscopic heating value sensor in which a reference light intensity measurement is made on a non-absorbing reference fluid, a light intensity measurement is made on a sample fluid, and a measured light absorbance of the sample fluid is determined. A corrective light intensity measurement at a non-absorbing wavelength of the sample fluid is made on the sample fluid from which an absorbance correction factor is determined. The absorbance correction factor is then applied to the measured light absorbance of the sample fluid to arrive at a true or accurate absorbance for the sample fluid.

  12. Uncertainty analysis for absorbed dose from a brain receptor imaging agent

    SciTech Connect

    Aydogan, B.; Miller, L.F.; Sparks, R.B.; Stubbs, J.B.

    1999-01-01

    Absorbed dose estimates are known to contain uncertainties. A recent literature search indicates that prior to this study no rigorous investigation of uncertainty associated with absorbed dose has been undertaken. A method of uncertainty analysis for absorbed dose calculations has been developed and implemented for the brain receptor imaging agent {sup 123}I-IPT. The two major sources of uncertainty considered were the uncertainty associated with the determination of residence time and that associated with the determination of the S values. There are many sources of uncertainty in the determination of the S values, but only the inter-patient organ mass variation was considered in this work. The absorbed dose uncertainties were determined for lung, liver, heart and brain. Ninety-five percent confidence intervals of the organ absorbed dose distributions for each patient and for a seven-patient population group were determined by the ``Latin Hypercube Sampling`` method. For an individual patient, the upper bound of the 95% confidence interval of the absorbed dose was found to be about 2.5 times larger than the estimated mean absorbed dose. For the seven-patient population the upper bound of the 95% confidence interval of the absorbed dose distribution was around 45% more than the estimated population mean. For example, the 95% confidence interval of the population liver dose distribution was found to be between 1.49E+0.7 Gy/MBq and 4.65E+07 Gy/MBq with a mean of 2.52E+07 Gy/MBq. This study concluded that patients in a population receiving {sup 123}I-IPT could receive absorbed doses as much as twice as large as the standard estimated absorbed dose due to these uncertainties.

  13. Warm Absorber Diagnostics of AGN Dynamics

    NASA Astrophysics Data System (ADS)

    Kallman, Timothy

    Warm absorbers and related phenomena are observable manifestations of outflows or winds from active galactic nuclei (AGN) that have great potential value. Understanding AGN outflows is important for explaining the mass budgets of the central accreting black hole, and also for understanding feedback and the apparent co-evolution of black holes and their host galaxies. In the X-ray band warm absorbers are observed as photoelectric absorption and resonance line scattering features in the 0.5-10 keV energy band; the UV band also shows resonance line absorption. Warm absorbers are common in low luminosity AGN and they have been extensively studied observationally. They may play an important role in AGN feedback, regulating the net accretion onto the black hole and providing mechanical energy to the surroundings. However, fundamental properties of the warm absorbers are not known: What is the mechanism which drives the outflow?; what is the gas density in the flow and the geometrical distribution of the outflow?; what is the explanation for the apparent relation between warm absorbers and the surprising quasi-relativistic 'ultrafast outflows' (UFOs)? We propose a focused set of model calculations that are aimed at synthesizing observable properties of warm absorber flows and associated quantities. These will be used to explore various scenarios for warm absorber dynamics in order to answer the questions in the previous paragraph. The guiding principle will be to examine as wide a range as possible of warm absorber driving mechanisms, geometry and other properties, but with as careful consideration as possible to physical consistency. We will build on our previous work, which was a systematic campaign for testing important class of scenarios for driving the outflows. We have developed a set of tools that are unique and well suited for dynamical calculations including radiation in this context. We also have state-of-the-art tools for generating synthetic spectra, which are

  14. Aluminum infrared plasmonic perfect absorbers for wavelength selective devices

    NASA Astrophysics Data System (ADS)

    Dao, Thang Duy; Ishii, Satoshi; Chen, Kai; Yokoyama, Takahiro; Nabatame, Toshihide; Nagao, Tadaaki

    2016-09-01

    We demonstrate the development of colloidal lithography technique to fabricate large-area plasmonic perfect absorbers using Al, which is an earth abundant low-cost plasmonic material in contrast to Au and Ag. Using numerical electromagnetic simulations, we optimize the geometrical parameters of Al perfect absorbers (AlPAs) with resonances at desired wavelengths depending on the applications. The fabricated AlPAs exhibit narrowband absorptions with high efficiency up to 98 %. By tuning AlPAs parameters, the resonance of AlPAs can be tuned from the visible to the middle infrared region. The AlPAs can be applied for spectrally selective infrared devices such as selective thermal emitters, selective surface-enhanced vibrational spectroscopy (SEIRA) for molecular sensing and selective IR detectors. In this report, we demonstrate applications of AlPAs for selective thermal emitters and SEIRA. The results obtained here reveal a simple technique to fabricate scalable plasmonic perfect absorbers as well as their potential applications in optoelectronic and photonic devices.

  15. 75 FR 58407 - Medicare Program; Medicare Appeals; Adjustment to the Amount in Controversy Threshold Amounts for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-24

    ... to the Amount in Controversy Threshold Amounts for Calendar Year 2011 AGENCY: Centers for Medicare... July of the preceding year involved and rounded to the nearest multiple of $10. B. Calendar Year 2011... judicial review will rise to $1,300 for the 2011 calendar year. These updated amounts are based on the...

  16. 77 FR 59618 - Medicare Program; Medicare Appeals; Adjustment to the Amount in Controversy Threshold Amounts for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-28

    ... to the Amount in Controversy Threshold Amounts for Calendar Year 2013 AGENCY: Centers for Medicare... for requests for ALJ hearings and judicial review filed on or after January 1, 2013. The calendar year... nearest multiple of $10. B. Calendar Year 2013 The AIC threshold amount for ALJ hearing requests...

  17. Oxygen absorbers in food preservation: a review.

    PubMed

    Cichello, Simon Angelo

    2015-04-01

    The preservation of packaged food against oxidative degradation is essential to establish and improve food shelf life, customer acceptability, and increase food security. Oxygen absorbers have an important role in the removal of dissolved oxygen, preserving the colour, texture and aroma of different food products, and importantly inhibition of food spoilage microbes. Active packaging technology in food preservation has improved over decades mostly due to the sealing of foods in oxygen impermeable package material and the quality of oxygen absorber. Ferrous iron oxides are the most reliable and commonly used oxygen absorbers within the food industry. Oxygen absorbers have been transformed from sachets of dried iron-powder to simple self-adhesive patches to accommodate any custom size, capacity and application. Oxygen concentration can be effectively lowered to 100 ppm, with applications spanning a wide range of food products and beverages across the world (i.e. bread, meat, fish, fruit, and cheese). Newer molecules that preserve packaged food materials from all forms of degradation are being developed, however oxygen absorbers remain a staple product for the preservation of food and pharmaceutical products to reduce food wastage in developed nations and increased food security in the developing & third world.

  18. Monte Carlo calculation of specific absorbed fractions: variance reduction techniques

    NASA Astrophysics Data System (ADS)

    Díaz-Londoño, G.; García-Pareja, S.; Salvat, F.; Lallena, A. M.

    2015-04-01

    The purpose of the present work is to calculate specific absorbed fractions using variance reduction techniques and assess the effectiveness of these techniques in improving the efficiency (i.e. reducing the statistical uncertainties) of simulation results in cases where the distance between the source and the target organs is large and/or the target organ is small. The variance reduction techniques of interaction forcing and an ant colony algorithm, which drives the application of splitting and Russian roulette, were applied in Monte Carlo calculations performed with the code penelope for photons with energies from 30 keV to 2 MeV. In the simulations we used a mathematical phantom derived from the well-known MIRD-type adult phantom. The thyroid gland was assumed to be the source organ and urinary bladder, testicles, uterus and ovaries were considered as target organs. Simulations were performed, for each target organ and for photons with different energies, using these variance reduction techniques, all run on the same processor and during a CPU time of 1.5 · 105 s. For energies above 100 keV both interaction forcing and the ant colony method allowed reaching relative uncertainties of the average absorbed dose in the target organs below 4% in all studied cases. When these two techniques were used together, the uncertainty was further reduced, by a factor of 0.5 or less. For photons with energies below 100 keV, an adapted initialization of the ant colony algorithm was required. By using interaction forcing and the ant colony algorithm, realistic values of the specific absorbed fractions can be obtained with relative uncertainties small enough to permit discriminating among simulations performed with different Monte Carlo codes and phantoms. The methodology described in the present work can be employed to calculate specific absorbed fractions for arbitrary arrangements, i.e. energy spectrum of primary radiation, phantom model and source and target organs.

  19. Differential ultraviolet-visible absorbance spectra for characterizing metal ions binding onto extracellular polymeric substances in different mixed microbial cultures.

    PubMed

    Yin, Cuiqin; Meng, Fangang; Meng, Yabing; Chen, Guang-Hao

    2016-09-01

    Ultraviolet-visible (UV-vis) absorbance spectra was adopted to quantify the binding of major metal ions (e.g., Na(I), Ca((II)), Fe(III), Cu(II), and Pb(II)) on extracellular polymeric substances (EPSs) extracted from different mixed cultures. The results showed that the differential absorbance spectra (DAS) provided discernible features for revealing the changes in optical properties of EPSs induced by metals, i.e., the intensity of DAS increased largely with incrementally increased metal concentrations (Fe(III), Cu(II), and Pb(II)). It can be assumed attributable to the changes in the conformations and inter-chromophores of the EPS biomolecules. In addition, the changes in spectral parameters of DSlope325-375 (spectral slope in the range of wavelengths 325-375 nm) and DA300 (differential absorbance at 300 nm) were found to be closely related to the amounts of metals bound onto all extracted EPSs, particularly for Fe(III) and Cu(II). The decreased SR (the ratio of slope275-295 to slope350-400) of the EPS solutions after dosage of metals suggested increased molecular weight or size of the EPS biomolecules. Deconvolution of the DAS yielded six Gaussian bands, which were present in all of the EPS samples with various metals. Moreover, the relative contributions of different Gaussian bands in the DAS were determined by the nature of EPS-metal ions interactions good correlated with the covalent-bonding index. This study concluded that DAS and selected spectral parameters (DA300, DSlope325-375 and SR) can be used to successfully characterize the binding of metals onto EPS at environmentally relevant concentrations.

  20. Non-Absorbable Gas Behavior in the Absorber/Evaporator of a Absorption Chiller

    NASA Astrophysics Data System (ADS)

    Suzuki, Hiroshi; Nagamoto, Wataru; Sugiyama, Takahide

    A two-dimensional numerical study on non-absorbable gas behavior in the absorber/evaporator of an absorption chiller has been performed. In the present study, the effect of the pitch-to-diameter ratio of a cylinder bundle in the absorber was highlighted. From the results, a sudden decrease of the overall heat transfer coefficient of the absorber was observed at a certain mean concentration of non-absorbable gas for each pitch-to-diameter ratio. Such a critical concentration was also found to decrease as the pitch-to- diameter ratio increased. The sudden decrease occurs due to the sudden disappearance of recirculating region, which is formed between the absorber and the evaporator, and where most of non-absorbable gas stays when it exists. As the pitch-to-diameter ratio increases, the recirculating region becomes weak because the velocity of the high velocity region supporting the recirculating flow decreases. Then, the critical mean concentration of non-absorbable gas is found to decrease as pitch-to-ratio increases.

  1. Optical analysis of solar energy tubular absorbers.

    PubMed

    Saltiel, C; Sokolov, M

    1982-11-15

    The energy absorbed by a solar energy tubular receiver element for a single incident ray is derived. Two types of receiver elements were analyzed: (1) an inner tube with an absorbing coating surrounded by a semitransparent cover tube, and (2) a semitransparent inner tube filled with an absorbing fluid surrounded by a semitransparent cover tube. The formation of ray cascades in the semitransparent tubes is considered. A numerical simulation to investigate the influence of the angle of incidence, sizing, thickness, and coefficient of extinction of the tubes was performed. A comparison was made between receiver elements with and without cover tubes. Ray tracing analyses in which rays were followed within the tubular receiver element as well as throughout the rest of the collector were performed for parabolic and circular trough concentrating collectors.

  2. Interference theory of metamaterial perfect absorbers.

    PubMed

    Chen, Hou-Tong

    2012-03-26

    The impedance matching to free space in metamaterial perfect absorbers has been believed to involve and rely on magnetic resonant response, with direct evidence provided by the anti-parallel surface currents in the metal structures. Here I present a different theoretical interpretation based on interference, which shows that the two layers of metal structures in metamaterial absorbers are linked only by multiple reflections with negligible near-field interactions or magnetic resonances. This is further supported by the out-of-phase surface currents derived at the interfaces of resonator array and ground plane through multiple reflections and superpositions. The theory developed here explains all features observed in narrowband metamaterial absorbers and therefore provides a profound understanding of the underlying physics.

  3. Translatory shock absorber for attitude sensors

    NASA Technical Reports Server (NTRS)

    Vonpragenau, G. L.; Morgan, I. T., Jr.; Kirby, C. A. (Inventor)

    1976-01-01

    A translatory shock absorber is provided for mounting an attitude sensor thereon for isolating a sensor from translatory vibrations. The translatory shock absorber includes a hollow block structure formed as one piece to form a parallelogram. The absorber block structure includes a movable top plate for supporting the attitude sensor and a fixed base plate with opposed side plates interposed between. At the junctions of the side plates, and the base and top plates, there are provided grooves which act as flexible hinges for attenuating translatory vibrations. A damping material is supported on a pedestal which is carried on the base plate between the side plates thereof. The top of the damping material rests against the bottom surface of the top plate for eliminating the resonant peaks of vibration.

  4. Absorber Materials at Room and Cryogenic Temperatures

    SciTech Connect

    F. Marhauser, T.S. Elliott, A.T. Wu, E.P. Chojnacki, E. Savrun

    2011-09-01

    We recently reported on investigations of RF absorber materials at cryogenic temperatures conducted at Jefferson Laboratory (JLab). The work was initiated to find a replacement material for the 2 Kelvin low power waveguide Higher Order Mode (HOM) absorbers employed within the original cavity cryomodules of the Continuous Electron Beam Accelerator Facility (CEBAF). This effort eventually led to suitable candidates as reported in this paper. Furthermore, though constrained by small funds for labor and resources, we have analyzed a variety of lossy ceramic materials, several of which could be usable as HOM absorbers for both normal conducting and superconducting RF structures, e.g. as loads in cavity waveguides and beam tubes either at room or cryogenic temperatures and, depending on cooling measures, low to high operational power levels.

  5. Ferrite HOM Absorber for the RHIC ERL

    SciTech Connect

    Hahn,H.; Choi, E.M.; Hammons, L.

    2008-10-01

    A superconducting Energy Recovery Linac is under construction at Brookhaven National Laboratory to serve as test bed for RHIC upgrades. The damping of higher-order modes in the superconducting five-cell cavity for the Energy-Recovery linac at RHIC is performed exclusively by two ferrite absorbers. The ferrite properties have been measured in ferrite-loaded pill box cavities resulting in the permeability values given by a first-order Debye model for the tiled absorber structure and an equivalent permeability value for computer simulations with solid ring dampers. Measured and simulated results for the higher-order modes in the prototype copper cavity are discussed. First room-temperature measurements of the finished niobium cavity are presented which confirm the effective damping of higher-order modes in the ERL. by the ferrite absorbers.

  6. Automatically acquired broadband plasmonic-metamaterial black absorber during the metallic film-formation.

    PubMed

    Liu, Zhengqi; Liu, Xiaoshan; Huang, Shan; Pan, Pingping; Chen, Jing; Liu, Guiqiang; Gu, Gang

    2015-03-04

    Broadband electromagnetic wave absorbers are highly desirable in numerous applications such as solar-energy harvesting, thermo-photovoltaics, and photon detection. The aim to efficiently achieve ultrathin broadband absorbers with high-yield and low-cost fabrication process has long been pursued. Here, we theoretically propose and experimentally demonstrate a unique broadband plasmonic-metamaterial absorber by utilizing a sub-10 nm meta-surface film structure to replace the precisely designed metamaterial crystal in the common metal-dielectric-metal absorbers. The unique ultrathin meta-surface can be automatically obtained during the metal film formation process. Spectral bandwidth with absorbance above 80% is up to 396 nm, where the full absorption width at half-maximum is about 92%. The average value of absorbance across the whole spectral range of 370-880 nm reaches 83%. These super absorption properties can be attributed to the particle plasmon resonances and plasmon near-field coupling by the automatically formed metallic nanoparticles as well as the plasmon polaritons of the metal film with the induced plasmonic magnetic resonances occurring between the top meta-surface and the bottom metal mirror. This method is quite simple, cost-effective for large-area fabrication, and compatible with current industrial methods for microelectro-mechanical systems, which makes it an outstanding candidate for advanced high-efficiency absorber materials.

  7. New procedure for direct measurements of absorbance of thin films of ultra-high absorbance UV blocks

    NASA Astrophysics Data System (ADS)

    McMillan, Norman D.; Solsvik, A.; Murphy, L.; Stevenson, A.; O'Neill, M.; Moore, J.

    2005-06-01

    A novel method for the measurement of ultra-high absorbance liquids has been devised and details are given of a new ultra absorbance instrument developed specifically for these thin liquid film measurements. The instrument specifically constructed for monitoring and measuring sunscreen products has been tested using locally produced sunscreen products. This new approach has been made possible by the development of very accurate liquid micro-dispensers and details are given of the novel procedure to carry out these measurements. Detailed description of the apparatus construction is given with photographs of the apparatus. The work described is largely based on research and quality control measurements of Parasol suncare products. Results on the reproducibility of measurements taken with the UAI for a commercial range of factor 20 sunscreen liquid are given and these have been used to validate the performance of the instrument. It is believed that the absorbance measurements described here are perhaps the largest ever reported. In addition, the photostability of this product has been monitored in aging tests. Finally, some studies have been done on two other commercially available factor 20 products that show that these are significantly worse with regards to both protection from ageing and burn.

  8. Optimization and engineering of microwave absorbers

    NASA Astrophysics Data System (ADS)

    Chen, Kuo-Liang

    1998-12-01

    In this thesis, a concerted effort has been made to study and evaluate the individual electromagnetic properties of the absorbing components including carbon black, conducting fibers, metal flakes, magnetic materials such as carbonyl iron, ferrite and the chiral type of micro- carbon coil. The study of the electromagnetic properties covers functions such as dielectric dissipation, random scattering effect at low and high frequencies, magnetic dissipation at high frequencies and also the effect of chirality for different angles of incidence. The results of these studies have been used in the design, engineering and optimization of the microwave absorbers. The objective of this thesis is to identify the absorption mechanism of each of various type of fillers and to study the synergic effect arising from a combination of these in a non-metallic host medium. This will help us in producing microwave absorbers suitable for broad band application with the advantages of light weight, having high strength and possessing good chemical resistance. The results from experimental measurements of various material combinations have been greatly influenced by the theoretical understanding of the absorption mechanism. Design of microwave absorbers is governed by the requirement of the users as well as the characteristics of the objects (targets) inferred by theoretical understanding and experimental data to arrive at the right formula. Finally a detailed quality control program has to be charted out reflecting both the electromagnetic as well as mechanical properties. This is done by carrying out the tests systematically on small samples and then proceeding to practical absorbers making use of the data compiled earlier on smaller samples. In this thesis, to modify all dielectric absorbing components including micro-carbon chirals to reduce the sensitivity of absorption for different incident angles is unprecedented topic.

  9. Absorber topography dependence of phase edge effects

    NASA Astrophysics Data System (ADS)

    Shanker, Aamod; Sczyrba, Martin; Connolly, Brid; Waller, Laura; Neureuther, Andy

    2015-10-01

    Mask topography contributes to phase at the wafer plane, even for OMOG binary masks currently in use at the 22nm node in deep UV (193nm) lithography. Here, numerical experiments with rigorous FDTD simulation are used to study the impact of mask 3D effects on aerial imaging, by varying the height of the absorber stack and its sidewall angle. Using a thin mask boundary layer model to fit to rigorous simulations it is seen that increasing the absorber thickness, and hence the phase through the middle of a feature (bulk phase) monotonically changes the wafer-plane phase. Absorber height also influences best focus, revealed by an up/down shift in the Bossung plot (linewidth vs. defocus). Bossung plot tilt, however, responsible for process window variability at the wafer, is insensitive to changes in the absorber height (and hence also the bulk phase). It is seen to depend instead on EM edge diffraction from the thick mask edge (edge phase), but stays constant for variations in mask thickness within a 10% range. Both bulk phase and edge phase are also independent of sidewall angle fluctuation, which is seen to linearly affect the CD at the wafer, but does not alter wafer phase or the defocus process window. Notably, as mask topography varies, the effect of edge phase can be replicated by a thin mask model with 8nm wide boundary layers, irrespective of absorber height or sidewall angle. The conclusions are validated with measurements on phase shifting masks having different topographic parameters, confirming the strong dependence of phase variations at the wafer on bulk phase of the mask absorber.

  10. Synthesis of the starch grafting of superabsorbent and high oil-absorbing resin.

    PubMed

    Xu, Zhi; Fei, Qingzhi; Zhang, Xiaoyu

    2013-12-01

    The graft copolymerization of the starch and acrylic were used to prepare the superabsorbent, and the high oil-absorbing resin was also studied preliminarily. In addition, following the method of the emulsion polymerization, the cerium nitrate amine was regarded as the initiator, the acrylic amide and the methyl methacrylate functioned as the monomer. There are several significant parameters taken into consideration such as the factors that influence the performance of the superabsorbent and the high oil-absorbing resin, the dosage of the initiator amount, the ratio of the starch and the monomer and the dosage of crosslinking agent.

  11. A Broadband Micro-Machined Far-Infrared Absorber

    NASA Technical Reports Server (NTRS)

    Wollack, E. J.; Datesman, A. M.; Jhabvala, C. A.; Miller, K. H.; Quijada, M. A.

    2016-01-01

    The experimental investigation of a broadband far-infrared meta-material absorber is described. The observed absorptance is greater than 0.95 from 1 to 20 terahertz (300-15 microns) over a temperature range spanning 5-300 degrees Kelvin. The meta-material, realized from an array of tapers approximately 100 microns in length, is largely insensitive to the detailed geometry of these elements and is cryogenically compatible with silicon-based micro-machined technologies. The electromagnetic response is in general agreement with a physically motivated transmission line model.

  12. Method and apparatus for determining the content and distribution of a thermal neutron absorbing material in an object

    DOEpatents

    Crane, Thomas W.

    1986-01-01

    The disclosure is directed to an apparatus and method for determining the content and distribution of a thermal neutron absorbing material within an object. Neutrons having an energy higher than thermal neutrons are generated and thermalized. The thermal neutrons are detected and counted. The object is placed between the neutron generator and the neutron detector. The reduction in the neutron flux corresponds to the amount of thermal neutron absorbing material in the object. The object is advanced past the neutron generator and neutron detector to obtain neutron flux data for each segment of the object. The object may comprise a space reactor heat pipe and the thermal neutron absorbing material may comprise lithium.

  13. Method and apparatus for determining the content and distribution of a thermal neutron absorbing material in an object

    DOEpatents

    Crane, T.W.

    1983-12-21

    The disclosure is directed to an apparatus and method for determining the content and distribution of a thermal neutron absorbing material within an object. Neutrons having an energy higher than thermal neutrons are generated and thermalized. The thermal neutrons are detected and counted. The object is placed between the neutron generator and the neutron detector. The reduction in the neutron flux corresponds to the amount of thermal neutron absorbing material in the object. The object is advanced past the neutron generator and neutron detector to obtain neutron flux data for each segment of the object. The object may comprise a space reactor heat pipe and the thermal neutron absorbing material may comprise lithium.

  14. Optical Properties and Aging of Light Absorbing Secondary Organic Aerosol

    SciTech Connect

    Liu, Jiumeng; Lin, Peng; Laskin, Alexander; Laskin, Julia; Kathmann, Shawn M.; Wise, Matthew E.; Caylor, Ryan; Imholt, Felisha; Selimovic, Vanessa; Shilling, John E.

    2016-10-14

    The light-absorbing organic aerosol (OA), commonly referred to as “brown carbon (BrC)”, has attracted considerable attention in recent years because of its potential to affect atmospheric radiation balance, especially in the ultraviolet region and thus impact photochemical processes. A growing amount of data has indicated that BrC is prevalent in the atmosphere, which has motivated numerous laboratory and field studies; however, our understanding of the relationship between the chemical composition and optical properties of BrC remains limited. We conducted chamber experiments to investigate the effect of various VOC precursors, NOx concentrations, photolysis time and relative humidity (RH) on the light absorption of selected secondary organic aerosols (SOA). Light absorption of chamber generated SOA samples, especially aromatic SOA, was found to increase with NOx concentration, at moderate RH, and for the shortest photolysis aging times. The highest mass absorption coefficients (MAC) value is observed from toluene SOA products formed under high NOx conditions at moderate RH, in which nitro-aromatics were previously identified as the major light absorbing compounds. BrC light absorption is observed to decrease with photolysis time, correlated with a decline of the organonitrate fraction of SOA. SOA formed from mixtures of aromatics and isoprene absorb less visible and UV light than SOA formed from aromatic precursors alone on a mass basis. However, the mixed-SOA absorption was underestimated when optical properties were predicted using a two-product SOA formation model, as done in many current climate models. Further investigation, including analysis on detailed mechanisms, are required to explain the discrepancy.

  15. Quantum walk with one variable absorbing boundary

    NASA Astrophysics Data System (ADS)

    Wang, Feiran; Zhang, Pei; Wang, Yunlong; Liu, Ruifeng; Gao, Hong; Li, Fuli

    2017-01-01

    Quantum walks constitute a promising ingredient in the research on quantum algorithms; consequently, exploring different types of quantum walks is of great significance for quantum information and quantum computation. In this study, we investigate the progress of quantum walks with a variable absorbing boundary and provide an analytical solution for the escape probability (the probability of a walker that is not absorbed by the boundary). We simulate the behavior of escape probability under different conditions, including the reflection coefficient, boundary location, and initial state. Moreover, it is also meaningful to extend our research to the situation of continuous-time and high-dimensional quantum walks.

  16. OSCEE fan exhaust bulk absorber treatment evaluation

    NASA Technical Reports Server (NTRS)

    Bloomer, H. E.; Samanich, N. E.

    1980-01-01

    The acoustic suppression capability of bulk absorber material designed for use in the fan exhaust duct walls of the quiet clean short haul experiment engine (OCSEE UTW) was evaluated. The acoustic suppression to the original design for the engine fan duct which consisted of phased single degree-of-freedom wall treatment was tested with a splitter and also with the splitter removed. Peak suppression was about as predicted with the bulk absorber configuration, however, the broadband characteristics were not attained. Post test inspection revealed surface oil contamination on the bulk material which could have caused the loss in bandwidth suppression.

  17. Analysis of Energy-Absorbing Foundations.

    DTIC Science & Technology

    1978-12-15

    1ENN51YVAN&A 5TATL UNIV UNIVERSITY PARK DEPT OF ENGI-CYTC F/S 13/h ANALYSIS OF ENERGY -ABSORBING POUNDATIONS.(U) ECC 78 V H NEUBERT, S Ji YIN DNA01-78...C-0036 UNCLASSIFIED DNA-48OFP NL "M~ENOMOEE MIflfl END ______ 1 32 112.2 MICROCOPY RILSOLUTION TEST CHIART LELL ,NA 480 MIL ANALYSIS OF ENERGY ...8217 REPORT & PERIOD COVERED Final Report for Period ANALYSIS OF ENERGY -ABSORBING FOUNDATIONS I Dee 77-1S Dee 78 6. PERFORMING ORG, REPORT NUMBER 7AUTHOR

  18. Shock-Absorbent Ball-Screw Mechanism

    NASA Technical Reports Server (NTRS)

    Hirr, Otto A., Jr.; Meneely, R. W.

    1986-01-01

    Actuator containing two ball screws in series employs Belleville springs to reduce impact loads, thereby increasing life expectancy. New application of springs increases reliability of equipment in which ball screws commonly used. Set of three springs within lower screw of ball-screw mechanism absorbs impacts that result when parts reach their upper and lower limits of movement. Mechanism designed with Belleville springs as shock-absorbing elements because springs have good energy-to-volume ratio and easily stacked to attain any stiffness and travel.

  19. Radio-Absorbing Nanocoatings on Corrugated Surfaces

    NASA Astrophysics Data System (ADS)

    Antipov, V. B.; Potekaev, A. I.; Vorozhtsov, A. B.; Melentyev, S. V.; Tsyganok, Yu. I.

    2016-12-01

    The feasibility of producing protective radio-absorbing shielding materials on the basis of differently shaped surfaces with nanostructured coatings is investigated. Combinations of special nanostructured materials and technical solutions for the shape of the absorbing surface were tested, in order to create efficient nanocoatings. It is shown that the coatings of interest that meet the requirements of low reflection and high attenuation of transmitted radiation combined with low coating thickness can be developed, using corrugated surfaces. Corrugated chicken egg-packing cell samples with nanostructured carbon coatings were examined and found to allow for effective shielding of electromagnetic radiation and to exhibit minimum reflection coefficients as compared to construction materials.

  20. Timing the warm absorber in NGC 4051

    NASA Astrophysics Data System (ADS)

    Silva, C. V.; Uttley, P.; Costantini, E.

    2016-12-01

    We investigated, using spectral-timing analysis, the characterization of highly ionized outflows in Seyfert galaxies, the so-called warm absorbers. Here, we present our results of the extensive 600 ks of XMM-Newton archival observations of the bright and highly variable Seyfert 1 galaxy NGC 4051 whose spectrum has revealed a complex multicomponent wind. Making use of both RGS and EPIC-pn data, we performed a detailed analysis through a time-dependent photoionization code in combination with spectral and Fourier spectral-timing techniques. The source light curves and the warm absorber parameters obtained from the data were used to simulate the response of the gas to variations in the ionizing flux of the central source. The resulting time variable spectra were employed to predict the effects of the warm absorber on the time lags and coherence of the energy dependent light curves. We have found that, in the absence of any other lag mechanisms, a warm absorber with the characteristics of the one observed in NGC 4051, is able to produce soft lags, up to 100 s, on timescales of hours. The time delay is associated with the response of the gas to changes in the ionizing source, either by photoionization or radiative recombination, which is dependent on its density. The range of radial distances that, under our assumptions, yield longer time delays are distances r 0.3-1.0 × 1016 cm, and hence gas densities n 0.4-3.0 × 107 cm-3. Since these ranges are comparable to the existing estimates of the location of the warm absorber in NGC 4051, we suggest that it is likely that the observed X-ray time lags may carry a signature of the warm absorber response time to changes in the ionizing continuum. Our results show that the warm absorber in NGC 4051 does not introduce lags on the short timescales associated with reverberation, but will likely modify the hard continuum lags seen on longer timescales, which in this source have been measured to be on the order of 50 s. Hence, these

  1. 33 CFR 133.7 - Requests: Amount.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; STATE ACCESS § 133.7... amount anticipated for immediate removal action for a single oil pollution incident, but, in any event... quantity and composition of the oil, weather conditions and customary costs of similar services in...

  2. 40 CFR 35.9050 - Assistance amount.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Assistance amount. 35.9050 Section 35.9050 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Financial Assistance for the National Estuary Program § 35.9050...

  3. 40 CFR 35.9050 - Assistance amount.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Assistance amount. 35.9050 Section 35.9050 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Financial Assistance for the National Estuary Program § 35.9050...

  4. 40 CFR 35.9050 - Assistance amount.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Assistance amount. 35.9050 Section 35.9050 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Financial Assistance for the National Estuary Program § 35.9050...

  5. 40 CFR 35.9050 - Assistance amount.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Assistance amount. 35.9050 Section 35.9050 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Financial Assistance for the National Estuary Program § 35.9050...

  6. 7 CFR 1421.304 - Payment amount.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 2012 Crop of Wheat, Barley, Oats, and Triticale § 1421.304 Payment amount. (a) The grazing payment rate... payment rate in effect for the predominant class of wheat in the county where the farm is located as of... three (3) similar farms. For triticale, the payment yield shall be the yield for wheat from three...

  7. 7 CFR 1421.304 - Payment amount.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 2012 Crop of Wheat, Barley, Oats, and Triticale § 1421.304 Payment amount. (a) The grazing payment rate... payment rate in effect for the predominant class of wheat in the county where the farm is located as of... three (3) similar farms. For triticale, the payment yield shall be the yield for wheat from three...

  8. 7 CFR 1421.304 - Payment amount.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 2012 Crop of Wheat, Barley, Oats, and Triticale § 1421.304 Payment amount. (a) The grazing payment rate... payment rate in effect for the predominant class of wheat in the county where the farm is located as of... three (3) similar farms. For triticale, the payment yield shall be the yield for wheat from three...

  9. 7 CFR 1421.304 - Payment amount.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 2012 Crop of Wheat, Barley, Oats, and Triticale § 1421.304 Payment amount. (a) The grazing payment rate... payment rate in effect for the predominant class of wheat in the county where the farm is located as of... three (3) similar farms. For triticale, the payment yield shall be the yield for wheat from three...

  10. 14 CFR 1300.13 - Guarantee amount.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Guarantee amount. 1300.13 Section 1300.13 Aeronautics and Space AIR TRANSPORTATION SYSTEM STABILIZATION OFFICE OF MANAGEMENT AND BUDGET AVIATION DISASTER RELIEF-AIR CARRIER GUARANTEE LOAN PROGRAM Minimum Requirements and Application Procedures §...

  11. 33 CFR 135.203 - Amount required.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OFFSHORE OIL POLLUTION COMPENSATION FUND Financial Responsibility for Offshore Facilities § 135.203 Amount required. (a) Each facility that is used for drilling for, producing, or processing oil, or which has the capacity to transport,...

  12. 33 CFR 135.203 - Amount required.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OFFSHORE OIL POLLUTION COMPENSATION FUND Financial Responsibility for Offshore Facilities § 135.203 Amount required. (a) Each facility that is used for drilling for, producing, or processing oil, or which has the capacity to transport,...

  13. 33 CFR 135.203 - Amount required.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OFFSHORE OIL POLLUTION COMPENSATION FUND Financial Responsibility for Offshore Facilities § 135.203 Amount required. (a) Each facility that is used for drilling for, producing, or processing oil, or which has the capacity to transport,...

  14. 21 CFR 1309.11 - Fee amounts.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ..., IMPORTERS AND EXPORTERS OF LIST I CHEMICALS Fees for Registration and Reregistration § 1309.11 Fee amounts..., or export a List I chemical, the applicant shall pay an annual fee of $1,147. Effective Date Note: At 77 FR 15250, Mar. 15, 2012, § 1309.11 was revised, effective April 16, 2012. For the convenience...

  15. Amount, composition and seasonality of dissolved organic carbon and nitrogen export from agriculture in contrasting climates

    NASA Astrophysics Data System (ADS)

    Graeber, Daniel; Meerhof, Mariana; Zwirnmann, Elke; Ovesen, Niels; Gelbrecht, Jörg; Teixeira de Mello, Franco; González-Bergonzoni, Ivan; Jeppesen, Erik; Kronvang, Brian

    2014-05-01

    Agricultural catchments are potentially important but often neglected sources of dissolved organic matter (DOM), of which a large part is dissolved organic carbon (DOC) and nitrogen (DON). DOC is an important source of aquatic microbial respiration and DON may be an important source of nitrogen to aquatic ecosystems. However, there is still a lack of comprehensive studies on the amount, composition and seasonality of DOM export from agricultural catchments in different climates. The aim of our study was to assess the amount, composition and seasonality of DOM in a total of four streams in the wet-temperate and subtropical climate of Denmark and Uruguay, respectively. In each climate, we investigated one stream with extensive agriculture (mostly pasture) and one stream with intensive agriculture (mostly intensively used arable land) in the catchment. We sampled each stream taking grab samples fortnightly for two years and measured DOC and DON concentration, as well as molecular composition by size-exclusion chromatography. We used absorbance, fluorescence and parallel factor analysis to gather additional information on the sources and composition of the DOM. The results were coupled to measurements of precipitation, water temperature, discharge, water residence time and physicochemical data measured at each study site to investigate the effects these environmental variables have on the amount and composition of DOM in the streams. Average annual DOM concentration and seasonality were highest in the stream with intensive agriculture in Uruguay and lowest in the stream with extensive agriculture in Denmark. In all streams, the molecular-size composition of DOC and DON were similar and most DOC and DON were exported as humic substances with low C:N ratio, which indicates high bioavailability. Moreover, DON was of higher relative importance in the Uruguayan streams than in the Danish streams, as can be seen from the lower dissolved inorganic to total dissolved nitrogen

  16. 21 CFR 880.6025 - Absorbent tipped applicator.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Absorbent tipped applicator. 880.6025 Section 880... Devices § 880.6025 Absorbent tipped applicator. (a) Identification. An absorbent tipped applicator is a device intended for medical purposes that consists of an absorbent swab on a wooden, paper, or...

  17. The Cooling of a Liquid Absorber using a Small Cooler

    SciTech Connect

    Baynham, D.E.; Bradshaw, T.W.; Green, M.A.; Ishimoto, S.; Liggins, N.

    2005-08-24

    This report discusses the use of small cryogenic coolers for cooling the Muon Ionization Cooling Experiment (MICE) liquid cryogen absorbers. Since the absorber must be able contain liquid helium as well liquid hydrogen, the characteristics of the available 4.2 K coolers are used here. The issues associated with connecting two-stage coolers to liquid absorbers are discussed. The projected heat flows into an absorber and the cool-down of the absorbers using the cooler are presented. The warm-up of the absorber is discussed. Special hydrogen safety issues that may result from the use of a cooler on the absorbers are also discussed.

  18. Tunable broadband metamaterial absorber consisting of ferrite slabs and a copper wire

    NASA Astrophysics Data System (ADS)

    Yang, Yong-Jun; Huang, Yong-Jun; Wen, Guang-Jun; Zhong, Jing-Ping; Sun, Hai-Bin; Oghenemuero, Gordon

    2012-03-01

    A tunable broadband metamaterial absorber is demonstrated at microwave frequencies in this paper. The metamaterial absorber is composed of ferrite slabs with large resonance beamwidths and a copper wire. The theoretical analysis for the effective media parameters is presented to show the mechanism for achieving the perfect absorptivity characteristic. The numerical results of transmission, reflectance, and absorptivity indicate that the metamaterial absorber exhibits a near perfect impedance-match to free space and a high absorptivity of 98.2% for one layer and 99.97% for two layers at 9.9 GHz. The bandwidth with the absorptivity above 90% is about 2.3 GHz. Moreover, the absorption band can be shifted linearly in a wide frequency range by adjusting the magnetic bias. This metamaterial absorber opens a way to prepare perfectly matched layers for engineering applications.

  19. Polarization-independent broadband absorber based on pyramidal metal-dielectric grating structure

    NASA Astrophysics Data System (ADS)

    Wu, Jun

    2016-12-01

    An infrared broadband polarization-independent metamaterial absorber is designed and investigated. It consists of a pyramidal metal-dielectric multilayered rectangle grating structure. The absorber exhibits near-unit absorption at multiple adjacent wavelengths overlapping with each other, which results in a high absorption over a wide wavelength range. The absorbance at normal incidence is higher than 90% in a wavelength range of 2321 nm-4631 nm, and the broadband absorption performance can be maintained over a large incident angle range. Furthermore, the mechanism of such broadband absorption are investigated by illustrating the electric field distributions for TE polarization and magnetic field distributions for TM polarization at the resonant wavelengths. It is believed that the conclusions can be applied for developing polarization-independent broadband absorber.

  20. Improved efficiency of butanol production by absorbed lignocellulose fermentation.

    PubMed

    He, Qin; Chen, Hongzhang

    2013-03-01

    Alkali-treated steam-exploded corn stover (SECSAT) was used as solid substrate for acetone-butanol-ethanol (ABE) production by absorbed lignocellulose fermentation (ALF) using Clostridium acetobutylicum ATCC 824. The ABE concentration in ALF culture had increased by 47% compared with that in submerged culture. More surprisingly, the acetone production was promoted and ethanol production was lower in the presence of SECSAT than that in its absence. ALF was also successfully in cofermentation of glucose and xylose, although decreased fermentability with an increase in the proportion of xylose. An invariable chemical composition and dry weight of SECSAT was found in ALF. Partial simultaneous saccharification and fermentation of SECSAT using a certain amount of cellulase could not only enhance the ABE concentration by 71%, but also significantly increase the area proportion of fiber cells in SECSAT from 53% to 90%, which would be an excellent paper making material.

  1. Tunable metamaterial dual-band terahertz absorber

    NASA Astrophysics Data System (ADS)

    Luo, C. Y.; Li, Z. Z.; Guo, Z. H.; Yue, J.; Luo, Q.; Yao, G.; Ji, J.; Rao, Y. K.; Li, R. K.; Li, D.; Wang, H. X.; Yao, J. Q.; Ling, F. R.

    2015-11-01

    We report a design of a temperature controlled tunable dual band terahertz absorber. The compact single unit cell consists of two nested closed square ring resonators and a layer metallic separated by a substrate strontium titanate (STO) dielectric layer. It is found that the absorber has two distinctive absorption peaks at frequencies 0.096 THz and 0.137 THz, whose peaks are attained 97% and 75%. Cooling the absorber from 400 K to 250 K causes about 25% and 27% shift compared to the resonance frequency of room temperature, when we cooling the temperature to 150 K, we could attained both the two tunabilities exceeding 53%. The frequency tunability is owing to the variation of the dielectric constant of the low-temperature co-fired ceramic (LTCC) substrate. The mechanism of the dual band absorber is attributed to the overlapping of dual resonance frequencies, and could be demonstrated by the distributions of the electric field. The method opens up avenues for designing tunable terahertz devices in detection, imaging, and stealth technology.

  2. Moving core beam energy absorber and converter

    DOEpatents

    Degtiarenko, Pavel V.

    2012-12-18

    A method and apparatus for the prevention of overheating of laser or particle beam impact zones through the use of a moving-in-the-coolant-flow arrangement for the energy absorbing core of the device. Moving of the core spreads the energy deposition in it in 1, 2, or 3 dimensions, thus increasing the effective cooling area of the device.

  3. Composition for absorbing hydrogen from gas mixtures

    DOEpatents

    Heung, Leung K.; Wicks, George G.; Lee, Myung W.

    1999-01-01

    A hydrogen storage composition is provided which defines a physical sol-gel matrix having an average pore size of less than 3.5 angstroms which effectively excludes gaseous metal hydride poisons while permitting hydrogen gas to enter. The composition is useful for separating hydrogen gas from diverse gas streams which may have contaminants that would otherwise render the hydrogen absorbing material inactive.

  4. Shock absorbing mount for electrical components

    NASA Technical Reports Server (NTRS)

    Dillon, R. F., Jr.; Mayne, R. C. (Inventor)

    1975-01-01

    A shock mount for installing electrical components on circuit boards is described. The shock absorber is made of viscoelastic material which interconnects the electrical components. With this system, shocks imposed on one component of the circuit are not transmitted to other components. A diagram of a typical circuit is provided.

  5. How to build a molecular shock absorber.

    PubMed

    McGough, A

    1999-12-02

    Newly determined structures of the alpha-helical repeats that make up the key 'rod' domains of spectrin and alpha-actinin - which serve as spacers between their actin-binding domains - have provided important insights into how these proteins function as molecular shock absorbers in cells.

  6. Shock absorber protects motive components against overloads

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Shock absorber with an output shaft, hollow gear, and a pair of springs forming a resilient driving connection between shaft and gear, operates when abnormally high torques are applied. This simple durable frictional device is valuable in rotating mechanisms subject to sudden overloads.

  7. Aldehyde-containing urea-absorbing polysaccharides

    NASA Technical Reports Server (NTRS)

    Mueller, W. A.; Hsu, G. C.; Marsh, H. E., Jr. (Inventor)

    1977-01-01

    A novel aldehyde containing polymer (ACP) is prepared by reaction of a polysaccharide with periodate to introduce aldehyde groups onto the C2 - C3 carbon atoms. By introduction of ether and ester groups onto the pendant primary hydroxyl solubility characteristics are modified. The ACP is utilized to absorb nitrogen bases such as urea in vitro or in vivo.

  8. Integrated tuned vibration absorbers: a theoretical study.

    PubMed

    Gardonio, Paolo; Zilletti, Michele

    2013-11-01

    This article presents a simulation study on two integrated tuned vibration absorbers (TVAs) designed to control the global flexural vibration of lightly damped thin structures subject to broad frequency band disturbances. The first one consists of a single axial switching TVA composed by a seismic mass mounted on variable axial spring and damper elements so that the characteristic damping and natural frequency of the absorber can be switched iteratively to control the resonant response of three flexural modes of the hosting structure. The second one consists of a single three-axes TVA composed by a seismic mass mounted on axial and rotational springs and dampers, which are arranged in such a way that the suspended mass is characterized by uncoupled heave and pitch-rolling vibrations. In this case the three damping and natural frequency parameters of the absorber are tuned separately to control three flexural modes of the hosting structure. The simulation study shows that the proposed single-unit absorbers produce, respectively, 5.3 and 8.7 dB reductions of the global flexural vibration of a rectangular plate between 20 and 120 Hz.

  9. Metamaterial Absorber Based Multifunctional Sensor Application

    NASA Astrophysics Data System (ADS)

    Ozer, Z.; Mamedov, A. M.; Ozbay, E.

    2017-02-01

    In this study metamaterial based (MA) absorber sensor, integrated with an X-band waveguide, is numerically and experimentally suggested for important application including pressure, density sensing and marble type detecting applications based on rectangular split ring resonator, sensor layer and absorber layer that measures of changing in the dielectric constant and/or the thickness of a sensor layer. Changing of physical, chemical or biological parameters in the sensor layer can be detected by measuring the resonant frequency shifting of metamaterial absorber based sensor. Suggested MA based absorber sensor can be used for medical, biological, agricultural and chemical detecting applications in microwave frequency band. We compare the simulation and experimentally obtained results from the fabricated sample which are good agreement. Simulation results show that the proposed structure can detect the changing of the refractive indexes of different materials via special resonance frequencies, thus it could be said that the MA-based sensors have high sensitivity. Additionally due to the simple and tiny structures it could be adapted to other electronic devices in different sizes.

  10. Emitter/absorber interface of CdTe solar cells

    SciTech Connect

    Song, Tao; Kanevce, Ana; Sites, James R.

    2016-06-17

    The performance of CdTe solar cells can be very sensitive to their emitter/absorber interfaces, especially for high-efficiency cells with improved bulk properties. When interface defect states are located at efficient recombination energies, performance losses from acceptor-type interface defects can be significant. Numerical simulations show that the emitter/absorber band alignment, the emitter doping and thickness, and the defect properties of the interface (i.e. defect density, defect type, and defect energy) can all play significant roles in the interface recombination. In particular, a type I heterojunction with small conduction-band offset (0.1 eV absorber inversion and hence a large hole barrier adjacent to the interface. As a result, the electron-hole recombination is suppressed due to an insufficient hole supply at the interface. A large spike (..delta..EC >/= 0.4 eV), however, can impede electron transport and lead to a reduction of photocurrent and fill-factor. In contrast to the spike, a 'cliff' (.delta..EC < 0 eV) is likely to allow many holes in the vicinity of the interface, which will assist interface recombination and result in a reduced open-circuit voltage. In addition, a thin and highly-doped emitter can invert the absorber, form a large hole barrier, and decrease device performance losses due to high interface defect density. CdS is the most common emitter material used in CdTe solar cells, but the CdS/CdTe interface is in the cliff category and is not favorable from the band-offset perspective. Other n-type emitter choices, such as (Mg,Zn)O, Cd(S,O), or (Cd,Mg)Te, can be tuned by varying the elemental ratio for an optimal positive value of ..delta..EC. These materials are predicted to yield higher

  11. Emitter/absorber interface of CdTe solar cells

    NASA Astrophysics Data System (ADS)

    Song, Tao; Kanevce, Ana; Sites, James R.

    2016-06-01

    The performance of CdTe solar cells can be very sensitive to the emitter/absorber interface, especially for high-efficiency cells with high bulk lifetime. Performance losses from acceptor-type interface defects can be significant when interface defect states are located near mid-gap energies. Numerical simulations show that the emitter/absorber band alignment, the emitter doping and thickness, and the defect properties of the interface (i.e., defect density, defect type, and defect energy) can all play significant roles in the interface recombination. In particular, a type I heterojunction with small conduction-band offset (0.1 eV ≤ ΔEC ≤ 0.3 eV) can help maintain good cell efficiency in spite of high interface defect density, much like with Cu(In,Ga)Se2 (CIGS) cells. The basic principle is that positive ΔEC, often referred to as a "spike," creates an absorber inversion and hence a large hole barrier adjacent to the interface. As a result, the electron-hole recombination is suppressed due to an insufficient hole supply at the interface. A large spike (ΔEC ≥ 0.4 eV), however, can impede electron transport and lead to a reduction of photocurrent and fill-factor. In contrast to the spike, a "cliff" (ΔEC < 0 eV) allows high hole concentration in the vicinity of the interface, which will assist interface recombination and result in a reduced open-circuit voltage. Another way to mitigate performance losses due to interface defects is to use a thin and highly doped emitter, which can invert the absorber and form a large hole barrier at the interface. CdS is the most common emitter material used in CdTe solar cells, but the CdS/CdTe interface is in the cliff category and is not favorable from the band-offset perspective. The ΔEC of other n-type emitter choices, such as (Mg,Zn)O, Cd(S,O), or (Cd,Mg)Te, can be tuned by varying the elemental ratio for an optimal positive value of ΔEC. These materials are predicted to yield higher voltages and would therefore be

  12. Light Absorbers and Catalysts for Solar to Fuel Conversion

    NASA Astrophysics Data System (ADS)

    Kornienko, Nikolay I.

    Increasing fossil fuel consumption and the resulting consequences to the environment has propelled research into means of utilizing alternative, clean energy sources. Solar power is among the most promising of renewable energy sources but must be converted into an energy dense medium such as chemical bonds to render it useful for transport and energy storage. Photoelectrochemistry (PEC), the splitting of water into oxygen and hydrogen fuel or reducing CO 2 to hydrocarbon fuels via sunlight is a promising approach towards this goal. Photoelectrochemical systems are comprised of several components, including light absorbers and catalysts. These parts must all synergistically function in a working device. Therefore, the continual development of each component is crucial for the overall goal. For PEC systems to be practical for large scale use, the must be efficient, stable, and composed of cost effective components. To this end, my work focused on the development of light absorbing and catalyst components of PEC solar to fuel converting systems. In the direction of light absorbers, I focused of utilizing Indium Phosphide (InP) nanowires (NWs) as photocathodes. I first developed synthetic techniques for InP NW solution phase and vapor phase growth. Next, I developed light absorbing photocathodes from my InP NWs towards PEC water splitting cells. I studied cobalt sulfide (CoSx) as an earth abundant catalyst for the reductive hydrogen evolution half reaction. Using in situ spectroscopic techniques, I elucidated the active structure of this catalyst and offered clues to its high activity. In addition to hydrogen evolution catalysts, I established a new generation of earth abundant catalysts for CO2 reduction to CO fuel/chemical feedstock. I first worked with molecularly tunable homogeneous catalysts that exhibited high selectivity for CO2 reduction in non-aqueous media. Next, in order to retain molecular tunability while achieving stability and efficiency in aqueous

  13. A study of warm absorbers in active galactic nuclei

    NASA Astrophysics Data System (ADS)

    Ashton, Ceri Ellen

    This thesis explores the 'warm absorber' phenomenon observed in Active Galactic Nuclei (AGN). Warm absorbers are clouds of ionised gas within AGN, that cause absorption at soft X-ray wavelengths. They are observed in half of all Type 1 AGN, hence they play an important part in the framework of our under standing of Active Galactic Nuclei. Observations with the satellite XMM-Newton have given us the highest signal-to-noise data yet. XMM-Newton observations of the quasars PG 1114+445 and PG 1309+355 are studied. Both quasars exhibit evidence for absorption by warm material in the line-of-sight. We define a 'phase' of absorption to have a single ionisation param eter and column density. From fits to the data, the absorption in PG 1114+445 is found to be in two phases, a 'hot' phase with a log ionisation parameter f of 2.57 and a column of 1022 cm-2, and a 'cooler' one with log f of 0.83 and a column of 1021 cm-2. The absorption in PG 1309+355 consists of a single phase, with log f of 1.87 and a column of 1021 cm-2. The absorbing gas lies at distances of 1019 - 1022 cm from the continuum radiation sources in these AGN, suggesting origins in a wind emanating from a molecular torus, according to the 'Standard Model' of AGN. The kinetic luminosities of the outflowing absorbers represent insignificant fractions (< 10 3) of the energy budgets of the AGN. Using data for the Seyfert 1 H 0557 385, the warm absorption is characterised by two phases, a phase with log £ of 0.48 and a column of 1021 cm-2, and a phase with log f of 1.63 and a column of 1022 cm-2. Neutral absorption is also present in the source, and possible origins for this are discussed. For a large sample, observations of warm absorbers are collated and compared with models.

  14. Ataxia induced by small amounts of alcohol

    PubMed Central

    Setta, F; Jacquy, J; Hildebrand, J; Manto, M

    1998-01-01

    A patient is described who exhibited cerebellar ataxia after drinking small amounts of alcohol. Intake of 5 g alcohol induced a gaze evoked nystagmus, a scanning speech, a body sway after eye closure, and bilateral postural leg tremor. Kinematic and EMG analysis of fast wrist movements showed normal movements before and marked hypermetria after alcohol intake. Dysmetria was due to abnormal programming of antagonist muscle activity.

 PMID:9728953

  15. Amplification of trace amounts of nucleic acids

    DOEpatents

    Church, George M.; Zhang, Kun

    2008-06-17

    Methods of reducing background during amplification of small amounts of nucleic acids employ careful analysis of sources of low level contamination. Ultraviolet light can be used to reduce nucleic acid contaminants in reagents and equipment. "Primer-dimer" background can be reduced by judicious design of primers. We have shown clean signal-to-noise with as little as starting material as one single human cell (.about.6 picogram), E. coli cell (.about.5 femtogram) or Prochlorococcus cell (.about.3 femtogram).

  16. Imaging of Damped Ly-alpha Absorbers

    NASA Astrophysics Data System (ADS)

    Jim, K. T. C.; Roth, K. C.

    1998-05-01

    Intervening H I gas clouds toward QSOs give rise to damped Ly-alpha absorption. Because of the high column density (N(H I)>= 2*E(20) cm(-2) ) these systems have been thought to be galactic disks in some stage of formation. However, because potential optical counterparts have not been identified for most damped Ly-alpha systems, it is possible that some of the absorbing systems could be dwarf irregular galaxies or low surface brightness galaxies, and are thus difficult to image. In any case, the absorbers are expected to have small angular separation from the QSOs, and so high resolution imaging is required to differentiate the absorbers from the QSOs. Because previous studies have not shown any dominant morphological form for the few candidate objects known, our images are obtained with the Hawaii tip-tilt system in order to achieve the best possible morphological classification. By imaging in the NIR and optical bands that bracket the 4000 Angstroms break of these Ly-alpha absorbers, we can more readily select candidate objects by photometrically constraining their redshifts. In our sample of 14 QSOs with abosorbers from 1absorbers (Kolhatkar et al.)

  17. Absorbed fractions for electrons in ellipsoidal volumes

    NASA Astrophysics Data System (ADS)

    Amato, E.; Lizio, D.; Baldari, S.

    2011-01-01

    We applied a Monte Carlo simulation in Geant4 in order to calculate the absorbed fractions for monoenergetic electrons in the energy interval between 10 keV and 2 MeV, uniformly distributed in ellipsoids made from soft tissue. For each volume, we simulated a spherical shape, four oblate and four prolate ellipsoids, and one scalene shape. For each energy and for every geometrical configuration, an analytical relationship between the absorbed fraction and a 'generalized radius' was found, and the dependence of the fit parameters from electron energy is discussed and fitted by proper parametric functions. With the proposed formulation, the absorbed fraction for electrons in the 10-2000 keV energy range can be calculated for all volumes and for every ellipsoidal shape of practical interest. This method can be directly applied to evaluation of the absorbed fraction from the radionuclide emission of monoenergetic electrons, such as Auger or conversion electrons. The average deposited energy per disintegration in the case of extended beta spectra can be evaluated through integration. Two examples of application to a pure beta emitter such as 90Y and to 131I, whose emission include monoenergetic and beta electrons plus gamma photons, are presented. This approach represent a generalization of our previous studies, allowing a comprehensive treatment of absorbed fractions from electron and photon sources uniformly distributed in ellipsoidal volumes of any ellipticity and volume, in the whole range of practical interest for internal dosimetry in nuclear medicine applications, as well as in radiological protection estimations of doses from an internal contamination.

  18. Absorbed fractions for electrons in ellipsoidal volumes.

    PubMed

    Amato, E; Lizio, D; Baldari, S

    2011-01-21

    We applied a Monte Carlo simulation in Geant4 in order to calculate the absorbed fractions for monoenergetic electrons in the energy interval between 10 keV and 2 MeV, uniformly distributed in ellipsoids made from soft tissue. For each volume, we simulated a spherical shape, four oblate and four prolate ellipsoids, and one scalene shape. For each energy and for every geometrical configuration, an analytical relationship between the absorbed fraction and a 'generalized radius' was found, and the dependence of the fit parameters from electron energy is discussed and fitted by proper parametric functions. With the proposed formulation, the absorbed fraction for electrons in the 10-2000 keV energy range can be calculated for all volumes and for every ellipsoidal shape of practical interest. This method can be directly applied to evaluation of the absorbed fraction from the radionuclide emission of monoenergetic electrons, such as Auger or conversion electrons. The average deposited energy per disintegration in the case of extended beta spectra can be evaluated through integration. Two examples of application to a pure beta emitter such as (90)Y and to (131)I, whose emission include monoenergetic and beta electrons plus gamma photons, are presented. This approach represent a generalization of our previous studies, allowing a comprehensive treatment of absorbed fractions from electron and photon sources uniformly distributed in ellipsoidal volumes of any ellipticity and volume, in the whole range of practical interest for internal dosimetry in nuclear medicine applications, as well as in radiological protection estimations of doses from an internal contamination.

  19. Neutron absorbers and methods of forming at least a portion of a neutron absorber

    SciTech Connect

    Guillen, Donna P; Porter, Douglas L; Swank, W David; Erickson, Arnold W

    2014-12-02

    Methods of forming at least a portion of a neutron absorber include combining a first material and a second material to form a compound, reducing the compound into a plurality of particles, mixing the plurality of particles with a third material, and pressing the mixture of the plurality of particles and the third material. One or more components of neutron absorbers may be formed by such methods. Neutron absorbers may include a composite material including an intermetallic compound comprising hafnium aluminide and a matrix material comprising pure aluminum.

  20. Absorbed dose thresholds and absorbed dose rate limitations for studies of electron radiation effects on polyetherimides

    NASA Technical Reports Server (NTRS)

    Long, Edward R., Jr.; Long, Sheila Ann T.; Gray, Stephanie L.; Collins, William D.

    1989-01-01

    The threshold values of total absorbed dose for causing changes in tensile properties of a polyetherimide film and the limitations of the absorbed dose rate for accelerated-exposure evaluation of the effects of electron radiation in geosynchronous orbit were studied. Total absorbed doses from 1 kGy to 100 MGy and absorbed dose rates from 0.01 MGy/hr to 100 MGy/hr were investigated, where 1 Gy equals 100 rads. Total doses less than 2.5 MGy did not significantly change the tensile properties of the film whereas doses higher than 2.5 MGy significantly reduced elongation-to-failure. There was no measurable effect of the dose rate on the tensile properties for accelerated electron exposures.

  1. Design of a non-traditional dynamic vibration absorber.

    PubMed

    Cheung, Y L; Wong, W O

    2009-08-01

    A non-traditional dynamic vibration absorber is proposed for the minimization of maximum vibration velocity response of a vibrating structure. Unlike the traditional damped absorber configuration, the proposed absorber has a linear viscous damper connecting the absorber mass directly to the ground instead of the main mass. Optimum parameters of the proposed absorber are derived based on the fixed-point theory for minimizing the maximum vibration velocity response of a single-degree-of-freedom system under harmonic excitation. The extent of reduction in maximum vibration velocity response of the primary system when using the traditional dynamic absorber is compared with that using the proposed one. Under the optimum tuning condition of the absorbers, it is proved analytically that the proposed absorber provides a greater reduction in maximum vibration velocity response of the primary system than the traditional absorber.

  2. Imaging highly absorbing nanoparticles using photothermal microscopy

    NASA Astrophysics Data System (ADS)

    Lussier, Simon-Alexandre; Moradi, Hamid; Price, Alain; Murugkar, Sangeeta

    2015-03-01

    Gold nanoparticles (NPs) have tremendous potential in biomedicine. They can be used as absorbing labels inside living cells for the purpose of biomedical imaging, biosensing as well as for photothermal therapy. We demonstrate photothermal imaging of highly-absorbing particles using a pump-probe setup. The photothermal signal is recovered by heterodyne detection, where the excitation pump laser is at 532 nm and the probe laser is at 638 nm. The sample is moved by a scanning stage. Proof of concept images of red polystyrene microspheres and gold nanoparticles are obtained with this home-built multimodal microscope. The increase in temperature at the surface of the gold NPs, due to the pump laser beam, can be directly measured by means of this photothermal microscope and then compared with the results from theoretical predictions. This technique will be useful for characterization of nanoparticles of different shapes, sizes and materials that are used in cancer diagnosis and therapy.

  3. Infrared bolometers with silicon nitride micromesh absorbers

    NASA Technical Reports Server (NTRS)

    Bock, J. J.; Turner, A. D.; DelCastillo, H. M.; Beeman, J. W.; Lange, A. E.; Mauskopf, P. D.

    1996-01-01

    Sensitive far infrared and millimeter wave bolometers fabricated from a freestanding membrane of low stress silicon nitride are reported. The absorber, consisting of a metallized silicon nitride micromesh thermally isolated by radial legs of silicon nitride, is placed in an integrating cavity to efficiently couple to single mode or multiple mode infrared radiation. This structure provides low heat capacity, low thermal conduction and minimal cross section to energetic particles. A neutron transmutation doped Ge thermister is bump bonded to the center of the device and read out with evaporated Cr-Au leads. The limiting performance of the micromesh absorber is discussed and the recent results obtained from a 300 mK cold stage are summarized.

  4. Impedance matched thin metamaterials make metals absorbing

    PubMed Central

    Mattiucci, N.; Bloemer, M. J.; Aközbek, N.; D'Aguanno, G.

    2013-01-01

    Metals are generally considered good reflectors over the entire electromagnetic spectrum up to their plasma frequency. Here we demonstrate an approach to tailor their absorbing characteristics based on the effective metamaterial properties of thin, periodic metallo-dielectric multilayers by exploiting a broadband, inherently non-resonant, surface impedance matching mechanism. Based on this mechanism, we design, fabricate and test omnidirectional, thin (<1 micron), polarization independent, extremely efficient absorbers (in principle being capable to reach A > 99%) over a frequency range spanning from the UV to the IR. Our approach opens new venues to design cost effective materials for many applications such as thermo-photovoltaic energy conversion devices, light harvesting for solar cells, flat panel display, infrared detectors, stray light reduction, stealth and others. PMID:24220284

  5. A sound absorbing metasurface with coupled resonators

    NASA Astrophysics Data System (ADS)

    Li, Junfei; Wang, Wenqi; Xie, Yangbo; Popa, Bogdan-Ioan; Cummer, Steven A.

    2016-08-01

    An impedance matched surface is able, in principle, to totally absorb the incident sound and yield no reflection, and this is desired in many acoustic applications. Here we demonstrate a design of impedance matched sound absorbing surface with a simple construction. By coupling different resonators and generating a hybrid resonance mode, we designed and fabricated a metasurface that is impedance-matched to airborne sound at tunable frequencies with subwavelength scale unit cells. With careful design of the coupled resonators, over 99% energy absorption at central frequency of 511 Hz with a 50% absorption bandwidth of 140 Hz is achieved experimentally. The proposed design can be easily fabricated, and is mechanically stable. The proposed metasurface can be used in many sound absorption applications such as loudspeaker design and architectural acoustics.

  6. Absorbing Software Testing into the Scrum Method

    NASA Astrophysics Data System (ADS)

    Tuomikoski, Janne; Tervonen, Ilkka

    In this paper we study, how to absorb software testing into the Scrum method. We conducted the research as an action research during the years 2007-2008 with three iterations. The result showed that testing can and even should be absorbed to the Scrum method. The testing team was merged into the Scrum teams. The teams can now deliver better working software in a shorter time, because testing keeps track of the progress of the development. Also the team spirit is higher, because the Scrum team members are committed to the same goal. The biggest change from test manager’s point of view was the organized Product Owner Team. Test manager don’t have testing team anymore, and in the future all the testing tasks have to be assigned through the Product Backlog.

  7. The ultimate chrome absorber in photomask making

    NASA Astrophysics Data System (ADS)

    Hashimoto, Masahiro; Iwashita, Hiroyuki; Kominato, Atsushi; Shishido, Hiroaki; Ushida, Masao; Mitsui, Hideaki

    2008-05-01

    193nm-immersion lithography is the most promising technology for 32nm-node device fabrication. A new Cr absorber (TFC) for 193-nm attenuated phase-shift blanks was developed to meet the photomask requirements without any additional process step, such as hardmask etching. TFC was introduced with a design concept of the vertical profile for shorter etching time, the over etching time reduction. As a result, the dry-etching time was dramatically improved by more than 20% shorter than the conventional Cr absorber (TF11) without any process changes. We confirmed that 150nm-resist thickness was possible by TFC. The 32nm technology-node requirement is fully supported by TFC with thinner CAR, such as resolution and CD performance.

  8. Accelerated life testing of solar absorber coatings

    NASA Astrophysics Data System (ADS)

    Carlsson, Bo; Moeller, K.; Frei, Ulrich; Koehl, Michael

    1994-09-01

    Results from a comprehensive case study on accelerated life testing of some selective solar collector absorber coatings for DHW systems are reviewed. The study was conducted within Task X `Solar Materials Research and Development' of the IEA Solar Heating and Cooling Program from 1987 to 1992 and is unique due to its quantitative and systematic approach for durability assessment. The work of case study involved the development of both experimental and theoretical tools to aid the assessment of service life or absorber coatings. This entailed performance analysis, failure analysis, microclimate characterization, environmental resistance testing and life date analysis. Predicted in-service degradation of coatings from accelerated life testing was found to be in fairly good agreement both qualitatively and quantitatively with what was actually observed on coatings installed and tested for three years in solar collectors working under typical DHW conditions.

  9. Fault Detection for Automotive Shock Absorber

    NASA Astrophysics Data System (ADS)

    Hernandez-Alcantara, Diana; Morales-Menendez, Ruben; Amezquita-Brooks, Luis

    2015-11-01

    Fault detection for automotive semi-active shock absorbers is a challenge due to the non-linear dynamics and the strong influence of the disturbances such as the road profile. First obstacle for this task, is the modeling of the fault, which has been shown to be of multiplicative nature. Many of the most widespread fault detection schemes consider additive faults. Two model-based fault algorithms for semiactive shock absorber are compared: an observer-based approach and a parameter identification approach. The performance of these schemes is validated and compared using a commercial vehicle model that was experimentally validated. Early results shows that a parameter identification approach is more accurate, whereas an observer-based approach is less sensible to parametric uncertainty.

  10. Investigations on Absorber Materials at Cryogenic Temperatures

    SciTech Connect

    Marhauser, Frank; Elliott, Thomas; Rimmer, Robert

    2009-05-01

    In the framework of the 12 GeV upgrade project for the Continuous Electron Beam Accelerator Facility (CEBAF) improvements are being made to refurbish cryomodules housing Thomas Jefferson National Accelerator Facility's (JLab) original 5-cell cavities. Recently we have started to look into a possible simplification of the existing Higher Order Mode (HOM) absorber design combined with the aim to find alternative material candidates. The absorbers are implemented in two HOM-waveguides immersed in the helium bath and operate at 2 K temperature. We have built a cryogenic setup to perform measurements on sample load materials to investigate their lossy characteristics and variations from room temperature down to 2 K. Initial results are presented in this paper.

  11. Vibration absorber modeling for handheld machine tool

    NASA Astrophysics Data System (ADS)

    Abdullah, Mohd Azman; Mustafa, Mohd Muhyiddin; Jamil, Jazli Firdaus; Salim, Mohd Azli; Ramli, Faiz Redza

    2015-05-01

    Handheld machine tools produce continuous vibration to the users during operation. This vibration causes harmful effects to the health of users for repeated operations in a long period of time. In this paper, a dynamic vibration absorber (DVA) is designed and modeled to reduce the vibration generated by the handheld machine tool. Several designs and models of vibration absorbers with various stiffness properties are simulated, tested and optimized in order to diminish the vibration. Ordinary differential equation is used to derive and formulate the vibration phenomena in the machine tool with and without the DVA. The final transfer function of the DVA is later analyzed using commercial available mathematical software. The DVA with optimum properties of mass and stiffness is developed and applied on the actual handheld machine tool. The performance of the DVA is experimentally tested and validated by the final result of vibration reduction.

  12. Disposable Diaper Absorbency: Improvements via Advanced Designs.

    PubMed

    Helmes, C Tucker; O'Connor, Robert; Sawyer, Larry; Young, Sharon

    2014-08-01

    Absorbency effectiveness in diapers has improved significantly in recent years with the advent of new ingredient combinations and advanced design features. With these features, many leading products maintain their dryness performance overnight. Considering the importance of holding liquid away from the skin, ongoing research in diaper construction focuses on strategies to increase the effectiveness to capture liquid and help avoid rewetting of infant skin. The layout and design of a disposable diaper allows for distribution of absorbency features where they can provide the optimal benefit. Clinical evidence indicates materials can keep moisture away from the skin in the diapered area, helping maintain proper skin hydration, minimizing irritation, and contributing to reduced rates of diaper rash.

  13. Development of optical tools for the characterization of selective solar absorber at elevated temperature

    NASA Astrophysics Data System (ADS)

    Giraud, Philemon; Braillon, Julien; Delord, Christine; Raccurt, Olivier

    2016-05-01

    Durability of solar components for CSP (Concentrated Solar Power Plant) technologies is a key point to lower cost and ensure their large deployment. These technologies concentrated the solar radiation by means of mirrors on a receiver tube where it is collected as thermal energy. The absorbers are submitted to strong environmental constraints and the degradation of their optical properties (emittance and solar absorbance) have a direct impact on performance. The objective is to develop new optical equipment for characterization of this solar absorber in condition of use that is to say in air and at elevated temperature. In this paper we present two new optical test benches developed for optical characterization of solar absorbers in condition of use up to 800°C. The first equipment is an integrated sphere with heated sample holder which measures the hemispherical reflectance between 280 and 2500 nm to calculate the solar absorbance at high temperature. The second optical test bench measures the emittance of samples up to 1000°C in the range of 1.25 to 28.57 µm. Results of high temperature measurements on a series of metallic absorbers with selective coating and refractory material for high thermal receiver are presented.

  14. Absorber Materials for Transition-Edge Sensor X-ray Microcalorimeters

    NASA Technical Reports Server (NTRS)

    Brown, Ari-David; Bandler, Simon; Brekosky, Regis; Chervenak, James; Figueroa-Feliciano, Enectali; Finkbeiner, Fred; Sadleir, Jack; Iyomoto, Naoko; Kelley, Richard; Kilbourne, Caroline; Porter, F. Scott; Smith, Stephen; Saab, Tarek; Sadleir, Jac,

    2007-01-01

    Arrays of superconducting transition-edge sensors (TES) can provide high spatial and energy resolution necessary for x-ray astronomy. High quantum efficiency and uniformity of response can be achieved with a suitable absorber material, in which absorber x-ray stopping power, heat capacity, and thermal conductivity are relevant parameters. Here we compare these parameters for bismuth and gold. We have fabricated electroplated gold, electroplated gold/electroplated bismuth, and evaporated gold/evaporated bismuth 8x8 absorber arrays and find that a correlation exists between the residual resistance ratio (RRR) and thin film microstructure. This finding indicates that we can tailor absorber material conductivity via microstructure alteration, so as to permit absorber thermalization on timescales suitable for high energy resolution x-ray microcalorimetry. We show that by incorporating absorbers possessing large grain size, including electroplated gold and electroplated gold/electroplated bismuth, into our current Mo/Au TES, devices with tunable heat capacity and energy resolution of 2.3 eV (gold) and 2.1 eV (gold/bismuth) FWHM at 6 keV have been fabricated.

  15. Wide band cryogenic ultra-high vacuum microwave absorber

    DOEpatents

    Campisi, I.E.

    1992-05-12

    An absorber waveguide assembly for absorbing higher order modes of microwave energy under cryogenic ultra-high vacuum conditions, that absorbs wide-band multi-mode energy. The absorber is of a special triangular shape, made from flat tiles of silicon carbide and aluminum nitride. The leading sharp end of the absorber is located in a corner of the waveguide and tapers to a larger cross-sectional area whose center is located approximately in the center of the wave guide. The absorber is relatively short, being of less height than the maximum width of the waveguide. 11 figs.

  16. Wide band cryogenic ultra-high vacuum microwave absorber

    DOEpatents

    Campisi, Isidoro E.

    1992-01-01

    An absorber wave guide assembly for absorbing higher order modes of microwave energy under cryogenic ultra-high vacuum conditions, that absorbs wide-band multi-mode energy. The absorber is of a special triangular shape, made from flat tiles of silicon carbide and aluminum nitride. The leading sharp end of the absorber is located in a corner of the wave guide and tapers to a larger cross-sectional area whose center is located approximately in the center of the wave guide. The absorber is relatively short, being of less height than the maximum width of the wave guide.

  17. Tech Transfer Webinar: Energy Absorbing Materials

    ScienceCinema

    Duoss, Eric

    2016-07-12

    A new material has been designed and manufactured at LLNL that can absorb mechanical energy--a cushion--while also providing protection against sheering. This ordered cellular material is 3D printed using direct ink writing techniques under development at LLNL. It is expected to find utility in application spaces that currently use unordered foams, such as sporting and consumer goods as well as defense and aerospace.

  18. Metamaterial Resonant Absorbers for Terahertz Sensing

    DTIC Science & Technology

    2015-12-01

    and their periodic nature , finite element (FE) modeling is the preferable means of designing metamaterials. In order to use metamaterials in sensors ...will incorporate the metamaterial absorber design of this research into a more efficient, cost effective, bi-material THz sensor that can be employed...in a variety of naval applications. 14. SUBJECT TERMS terahertz sensors , metamaterials, uncooled detectors 15. NUMBER OF PAGES 73 16

  19. Lightweight Energy Absorbers for Blast Containers

    NASA Technical Reports Server (NTRS)

    Balles, Donald L.; Ingram, Thomas M.; Novak, Howard L.; Schricker, Albert F.

    2003-01-01

    Kinetic-energy-absorbing liners made of aluminum foam have been developed to replace solid lead liners in blast containers on the aft skirt of the solid rocket booster of the space shuttle. The blast containers are used to safely trap the debris from small explosions that are initiated at liftoff to sever frangible nuts on hold-down studs that secure the spacecraft to a mobile launch platform until liftoff.

  20. Design and Manufacture of Energy Absorbing Materials

    ScienceCinema

    Duoss, Eric

    2016-07-12

    Learn about an ordered cellular material that has been designed and manufactured using direct ink writing (DIW), a 3-D printing technology being developed at LLNL. The new material is a patterned cellular material that can absorb mechanical energy-a cushion-while also providing protection against sheering. This material is expected to find utility in application spaces that currently use unordered foams, such as sporting and consumer goods as well as defense and aerospace.

  1. Tech Transfer Webinar: Energy Absorbing Materials

    SciTech Connect

    Duoss, Eric

    2014-06-17

    A new material has been designed and manufactured at LLNL that can absorb mechanical energy--a cushion--while also providing protection against sheering. This ordered cellular material is 3D printed using direct ink writing techniques under development at LLNL. It is expected to find utility in application spaces that currently use unordered foams, such as sporting and consumer goods as well as defense and aerospace.

  2. Design and Manufacture of Energy Absorbing Materials

    SciTech Connect

    Duoss, Eric

    2014-05-28

    Learn about an ordered cellular material that has been designed and manufactured using direct ink writing (DIW), a 3-D printing technology being developed at LLNL. The new material is a patterned cellular material that can absorb mechanical energy-a cushion-while also providing protection against sheering. This material is expected to find utility in application spaces that currently use unordered foams, such as sporting and consumer goods as well as defense and aerospace.

  3. Shock wave absorber having a deformable liner

    DOEpatents

    Youngdahl, C.K.; Wiedermann, A.H.; Shin, Y.W.; Kot, C.A.; Ockert, C.E.

    1983-08-26

    This invention discloses a shock wave absorber for a piping system carrying liquid. The absorber has a plastically deformable liner defining the normal flow boundary for an axial segment of the piping system, and a nondeformable housing is spaced outwardly from the liner so as to define a gas-tight space therebetween. The flow capacity of the liner generally corresponds to the flow capacity of the piping system line, but the liner has a noncircular cross section and extends axially of the piping system line a distance between one and twenty times the diameter thereof. Gas pressurizes the gas-tight space equal to the normal liquid pressure in the piping system. The liner has sufficient structural capacity to withstand between one and one-half and two times this normal liquid pressures; but at greater pressures it begins to plastically deform initially with respect to shape to a more circular cross section, and then with respect to material extension by circumferentially stretching the wall of the liner. A high energy shock wave passing through the liner thus plastically deforms the liner radially into the gas space and progressively also as needed in the axial direction of the shock wave to minimize transmission of the shock wave beyond the absorber.

  4. Microscopic modeling of nitride intersubband absorbance

    NASA Astrophysics Data System (ADS)

    Montano, Ines; Allerman, A. A.; Wierer, J. J.; Moseley, M.; Skogen, E. J.; Tauke-Pedretti, A.; Vawter, G. A.

    III-nitride intersubband structures have recently attracted much interest because of their potential for a wide variety of applications ranging from electro-optical modulators to terahertz quantum cascade lasers. To overcome present simulation limitations we have developed a microscopic absorbance simulator for nitride intersubband devices. Our simulator calculates the band structure of nitride intersubband systems using a fully coupled 8x8 k.p Hamiltonian and determines the material response of a single period in a density-matrix-formalism by solving the Heisenberg equation including many-body and dephasing contributions. After calculating the polarization due to intersubband transitions in a single period, the resulting absorbance of a superlattice structure including radiative coupling between the different periods is determined using a non-local Green's-function formalism. As a result our simulator allows us to predict intersubband absorbance of superlattice structures with microscopically determined lineshapes and linewidths accounting for both many-body and correlation contributions. This work is funded by Sandia National Laboratories Laboratory Directed Research and Development program. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin.

  5. Heaving buoys, point absorbers and arrays.

    PubMed

    Falnes, Johannes; Hals, Jørgen

    2012-01-28

    Absorption of wave energy may be considered as a phenomenon of interference between incident and radiated waves generated by an oscillating object; a wave-energy converter (WEC) that displaces water. If a WEC is very small in comparison with one wavelength, it is classified as a point absorber (PA); otherwise, as a 'quasi-point absorber'. The latter may be a dipole-mode radiator, for instance an immersed body oscillating in the surge mode or pitch mode, while a PA is so small that it should preferably be a source-mode radiator, for instance a heaving semi-submerged buoy. The power take-off capacity, the WEC's maximum swept volume and preferably also its full physical volume should be reasonably matched to the wave climate. To discuss this matter, two different upper bounds for absorbed power are applied in a 'Budal diagram'. It appears that, for a single WEC unit, a power capacity of only about 0.3 MW matches well to a typical offshore wave climate, and the full physical volume has, unfortunately, to be significantly larger than the swept volume, unless phase control is used. An example of a phase-controlled PA is presented. For a sizeable wave-power plant, an array consisting of hundreds, or even thousands, of mass-produced WEC units is required.

  6. Load limiting energy absorbing lightweight debris catcher

    NASA Technical Reports Server (NTRS)

    Kahn, Jon B. (Inventor); Schneider, William C. (Inventor)

    1991-01-01

    In the representative embodiment of the invention disclosed, a load limiting, energy absorbing net is arranged to overlay a normally-covered vent opening in the rear bulkhead of the space orbiter vehicle. Spatially-disposed flexible retainer straps are extended from the net and respectively secured to bulkhead brackets spaced around the vent opening. The intermediate portions of the straps are doubled over and stitched together in a pattern enabling the doubled-over portions to progressively separate at a predicable load designed to be well below the tensile capability of the straps as the stitches are successively torn apart by the forces imposed on the retainer members whenever the cover plate is explosively separated from the bulkhead and propelled into the net. By arranging these stitches to be successively torn away at a load below the strap strength in response to forces acting on the retainers that are less than the combined strength of the retainers, this tearing action serves as a predictable compact energy absorber for safely halting the cover plate as the retainers are extended as the net is deployed. The invention further includes a block of an energy-absorbing material positioned in the net for receiving loose debris produced by the explosive release of the cover plate.

  7. Gallbladder perforation by absorbable spiral tacker

    PubMed Central

    Wirsching, A; Vonlanthen, R

    2014-01-01

    Introduction Mesh fixation with tacker systems is common in laparoscopic and open hernia repair. Complications due to absorbable tackers are rare and have not been described in the literature. However, we report a case of gallbladder erosion due to tacker dislocation. Methods An open hernia repair was performed using an intraperitoneal onlay mesh for a recurrent parastomal hernia after two previous mesh repairs in a 67-year-old patient. Results On postoperative day 2, the patient was reoperated because of a dislocated tacker that eroded and perforated the fundus region of the gallbladder. Putatively, tacker dislocation occurred owing to imbalanced traction forces. Initially, the mesh was fixed with absorbable tackers around the stoma on the right and transmuscular suture fixation was carried out on the left abdominal side. On revision surgery, tension forces to the right were therefore neutralised by additional transmuscular sutures on the right side. Conclusions Absorbable tackers in open hernia repair provide a safe and effective mesh fixation if tension forces are carefully avoided. PMID:25245719

  8. Development of monofilar rotor hub vibration absorber

    NASA Technical Reports Server (NTRS)

    Duh, J.; Miao, W.

    1983-01-01

    A design and ground test program was conducted to study the performance of the monofilar absorber for vibration reduction on a four-bladed helicopter. A monofilar is a centrifugal tuned two degree-of-freedom rotor hub absorber that provides force attenuation at two frequencies using the same dynamic mass. Linear and non-linear analyses of the coupled monofilar/airframe system were developed to study tuning and attenuation characteristics. Based on the analysis, a design was fabricated and impact bench tests verified the calculated non-rotating natural frequencies and mode shapes. Performance characteristics were measured using a rotating absorber test facility. These tests showed significant attenuation of fixed-system 4P hub motions due to 3P inplane rotating-system hub forces. In addition, detuning effects of the 3P monofilar modal response were small due to the nonlinearities and tuning pin slippage. However, attenuation of 4P hub motions due to 5P inplane hub forces was poor. The performance of the 5P monofilar modal response was degraded by torsional motion of the dynamic mass relative to the support arm which resulted in binding of the dynamic components. Analytical design studies were performed to evaluate this torsional motion problem. An alternative design is proposed which may alleviate the torsional motion of the dynamic mass.

  9. Timing the warm absorber in NGC4051

    NASA Astrophysics Data System (ADS)

    Silva, C.; Uttley, P.; Costantini, E.

    2015-07-01

    In this work we have combined spectral and timing analysis in the characterization of highly ionized outflows in Seyfert galaxies, the so-called warm absorbers. Here, we present our results on the extensive ˜600ks of XMM-Newton archival observations of the bright and highly variable Seyfert 1 galaxy NGC4051, whose spectrum has revealed a complex multi-component wind. Working simultaneously with RGS and PN data, we have performed a detailed analysis using a time-dependent photoionization code in combination with spectral and Fourier timing techniques. This method allows us to study in detail the response of the gas due to variations in the ionizing flux of the central source. As a result, we will show the contribution of the recombining gas to the time delays of the most highly absorbed energy bands relative to the continuum (Silva, Uttley & Costantini in prep.), which is also vital information for interpreting the continuum lags associated with propagation and reverberation effects in the inner emitting regions. Furthermore, we will illustrate how this powerful method can be applied to other sources and warm-absorber configurations, allowing for a wide range of studies.

  10. High-performance terahertz wave absorbers made of silicon-based metamaterials

    SciTech Connect

    Yin, Sheng; Zhu, Jianfei; Jiang, Wei; Yuan, Jun; Yin, Ge; Ma, Yungui; Xu, Wendao; Xie, Lijuan; Ying, Yibin

    2015-08-17

    Electromagnetic (EM) wave absorbers with high efficiency in different frequency bands have been extensively investigated for various applications. In this paper, we propose an ultra-broadband and polarization-insensitive terahertz metamaterial absorber based on a patterned lossy silicon substrate. Experimentally, a large absorption efficiency more than 95% in a frequency range of 0.9–2.5 THz was obtained up to a wave incident angle as large as 70°. Much broader absorption bandwidth and excellent oblique incidence absorption performance are numerically demonstrated. The underlying mechanisms due to the combination of a waveguide cavity mode and impedance-matched diffraction are analyzed in terms of the field patterns and the scattering features. The monolithic THz absorber proposed here may find important applications in EM energy harvesting systems such as THz barometer or biosensor.

  11. Glory on Venus cloud tops and the unknown UV absorber

    NASA Astrophysics Data System (ADS)

    Markiewicz, W. J.; Petrova, E.; Shalygina, O.; Almeida, M.; Titov, D. V.; Limaye, S. S.; Ignatiev, N.; Roatsch, T.; Matz, K. D.

    2014-05-01

    We report on the implications of the observations of the glory phenomenon made recently by Venus Express orbiter. Glory is an optical phenomenon that poses stringent constraints on the cloud properties. These observations thus enable us to constrain two properties of the particles at the cloud tops (about 70 km altitude) which are responsible for a large fraction of the solar energy absorbed by Venus. Firstly we obtain a very accurate estimate of the cloud particles size to be 1.2 μm with a very narrow size distribution. We also find that for the two observations presented here the clouds are homogenous, as far as cloud particles sizes are concerned, on scale of at least 1200 km. This is in contrast to previous estimates that were either local, from entry probes data, or averaged over space and time from polarization data. Secondly we find that the refractive index for the data discussed here is higher than that of sulfuric acid previously proposed for the clouds composition (Hansen, J.E., Hovenier, J.W. [1974]. J. Atmos. Sci. 31, 1137-1160; Ragent, B. et al. [1985]. Adv. Space Res. 5, 85-115). Assuming that the species contributing to the increase of the refractive index is the same as the unknown UV absorber, we are able to constrain the list of candidates. We investigated several possibilities and argue that either small ferric chloride (FeCl3) cores inside sulfuric acid particles or elemental sulfur coating their surface are good explanations of the observation. Both ferric chloride and elemental sulfur have been suggested in the past as candidates for the as yet unknown UV absorber (Krasnopolsky, V.A. [2006]. Planet. Space Sci. 54, 1352-1359; Mills, F.P. et al. [2007]. In: Esposito, L.W., Stofan, E.R., Cravens, T.E. (Eds.), Exploring Venus as a Terrestrial Planet, vol. 176. AGU Monogr. Ser., Washington, DC, pp. 73-100).

  12. Development of tritiated vapor absorbent applicable to the atmospheric detritiation system in a nuclear facility.

    PubMed

    Iwai, Yasunori; Yamanishi, Toshihiko

    2010-09-01

    The combination of hydrogen oxidation reactor packed noble metal catalysts and water vapor absorber has been applied to the atmospheric detritiation system of the tritium handling facility. Commercial synthetic zeolite such as molecular sieve 5A has been used as an adsorbent of ADS absorber. In the case of application of molecular sieve 5A to the ADS absorber of a large-scale tritium handling facility such as a future fusion plant, an absorber becomes huge due mainly to the difficulty in dehydration from molecular sieve 5A. Hence, application of CaY Faujasite-type zeolite with a high framework silica-to-alumina ratio to the adsorbent for atmospheric detritiation system was investigated. It was clear that the dehydration behavior at room temperature was significantly improved using CaY zeolite. In contrast, detritiation factor for CaY zeolite with a high framework silica-to-alumina ratio depended strongly on the space velocity through the absorber. To apply CaY zeolite with a high framework SiO(2)/Al(2)O(3) ratio to the ADS absorbent, the space velocity less than 250h(-1) was recommended to maintain the detritiation factor more than 1000. The steep increase in water adsorption at the relative pressure lower than 0.05 is a feature of synthetic zeolite with calcium cation. However, such an increase was not observed in water adsorption on CaY zeolite with a framework SiO(2)/Al(2)O(3) ratio more than 7.0. Consequently, the CaY zeolite with the framework SiO(2)/Al(2)O(3) ratio of 5.0 is a promising candidate as absorbent of ADS absorber.

  13. Effective Use of Low Temperature Heat Sources by Using Confined State of Water in Various Microporous Absorbents

    NASA Astrophysics Data System (ADS)

    Mizota, Tadato

    2006-05-01

    Energy saving is the most serious issue to sustain our life on the earth. Despite the limiting energy resources, we have been wasting enormous amount of heat from various places, such as factories, transportation systems and even houses, private or public. The exposed heat is difficult to use due to the nature of low temperature and low energy density, although the total amount is very large. We therefore lose much electric energy only to fell room temperatures by few degrees in summer, although electricity should be used for any other higher-grade objects. Zeolite heat pump was proposed initially for effective use of low grade-energy for cooling, such as air-conditioning and refrigeration, but few practical application have been developed so far. Here, I emphasize that we have no other way except for using absorbing states of vapor in micro-porous materials for effective energy-conversion from the low grade-energy. The zeolite-water combination may be one of the most prospective pair for the object, because the energy state of water molecules in zeolites is so low even at the room temperatures as to be comparable to that of ice at 0K. Zeolite heat pump system should be recognized as a mechanism to extract energy from the low entropy state of zeolitic water.

  14. 29 CFR 4219.14 - Amount of liability for 20-year-limitation amounts.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... amount equal to the present value of all initial withdrawal liability payments for which the employer was not liable pursuant to section 4219(c)(1)(B) of ERISA. The present value of such payments shall...

  15. Ultrasonic Atomization Amount for Different Frequencies

    NASA Astrophysics Data System (ADS)

    Yasuda, Keiji; Honma, Hiroyuki; Xu, Zheng; Asakura, Yoshiyuki; Koda, Shinobu

    2011-07-01

    The mass flow rate of ultrasonic atomization was estimated by measuring the vaporization amount from a bulk liquid with a fountain. The effects of ultrasonic frequency and intensity on the atomization characteristics were investigated when the directivities of the acoustic field from a transducer were almost the same. The sample was distillated water and the ultrasonic frequencies were 0.5, 1.0, and 2.4 MHz. The mass flow rate of ultrasonic atomization increased with increasing ultrasonic intensity and decreasing ultrasonic frequency. The fountain was formed at the liquid surface where the effective value of acoustic pressure was above atmospheric pressure. The fountain height was strongly governed by the acoustic pressure at the liquid surface of the transducer center. At the same ultrasonic intensity, the dependence of ultrasonic frequency on the number of atomized droplets was small. At the same apparent surface area of the fountain, the number of atomized droplets became larger as the ultrasonic frequency increased.

  16. Modeling the Effect of Polychromatic Light in Quantitative Absorbance Spectroscopy

    ERIC Educational Resources Information Center

    Smith, Rachel; Cantrell, Kevin

    2007-01-01

    Laboratory experiment is conducted to give the students practical experience with the principles of electronic absorbance spectroscopy. This straightforward approach creates a powerful tool for exploring many of the aspects of quantitative absorbance spectroscopy.

  17. Spectrophotometry of Thin Films of Light-Absorbing Particles.

    PubMed

    Binks, Bernard P; Fletcher, Paul D I; Johnson, Andrew J; Marinopoulos, Ioannis; Crowther, Jonathan M; Thompson, Michael A

    2017-04-06

    Thin films of dispersions of light-absorbing solid particles or emulsions containing a light-absorbing solute all have a nonuniform distribution of light-absorbing species throughout the sample volume. This results in nonuniform light absorption over the illuminated area, which causes the optical absorbance, as measured using a conventional specular UV-vis spectrophotometer, to deviate from the Beer-Lambert relationship. We have developed a theoretical model to account for the absorbance properties of such films, which are shown to depend on the size and volume fraction of the light-absorbing particles plus other sample variables. We have compared model predictions with measured spectra for samples consisting of emulsions containing a dissolved light-absorbing solute. Using no adjustable parameters, the model successfully predicts the behavior of nonuniform, light-absorbing emulsion films with varying values of droplet size, volume fraction, and other parameters.

  18. Radiation environments and absorbed dose estimations on manned space missions.

    PubMed

    Curtis, S B; Atwell, W; Beever, R; Hardy, A

    1986-01-01

    In order to make an assessment of radiation risk during manned missions in space, it is necessary first to have as accurate an estimation as possible of the radiation environment within the spacecraft to which the astronauts will be exposed. Then, with this knowledge and the inclusion of body self-shielding, estimations can be made of absorbed doses for various body organs (skin, eye, blood-forming organs, etc.). A review is presented of our present knowledge of the radiation environments and absorbed doses expected for several space mission scenarios selected for our development of the new radiation protection guidelines. The scenarios selected are a 90-day mission at an altitude (450 km) and orbital inclinations (28.5 degrees, 57 degrees and 90 degrees) appropriate for NASA's Space Station, a 15-day sortie to geosynchronous orbit and a 90-day lunar mission. All scenarios chosen yielded dose equivalents between five and ten rem to the blood forming organs if no large solar particle event were encountered. Such particle events could add considerable exposure particularly to the skin and eye for all scenarios except the one at 28.5 degrees orbital inclination.

  19. Porphyrin Based Near Infrared-Absorbing Materials for Organic Photovoltaics

    NASA Astrophysics Data System (ADS)

    Zhong, Qiwen

    photosynthesis. Photosynthesis uses light from the sun to drive a series of chemical reactions. Most natural photosynthetic systems utilize chlorophylls to absorb light energy and carry out photochemical charge separation that stores energy in the form of chemical bonds. The sun produces a broad spectrum of light output that ranges from gamma rays to radio waves. The entire visible range of light (400-700 nm) and some wavelengths in the NIR (700-1000 nm), are highly active in driving photosynthesis. Although the most familiar chlorophyll-containing organisms, such as plants, algae and cyanobacteria, cannot use light longer than 700 nm, anoxygenic bacterium containing bacteriochlorophylls can use the NIR part of the solar spectrum. No organism is known to utilize light of wavelength longer than about 1000 nm for photosynthesis. NIR light has a very low-energy content in each photon, so that large numbers of these low-energy photons would have to be used to drive the chemical reactions of photosynthesis. This is thermodynamically possible but would require a fundamentally different molecular mechanism that is more akin to a heat engine than to photochemistry. Early work on developing light absorbing materials for OPVs was inspired by photosynthesis in which light is absorbed by chlorophyll. Structurally related to chlorophyll is the porphyrin family, which has accordingly drawn much interest as the potential light absorbing component in OPV applications. In this dissertation, the design and detail studies of several porphyrin-based NIR absorbing materials, including pi--extended perylenyl porphryins and pyrazole-containing carbaporphyrins, as well as porphyrin modified single-walled carbon nanotube hybrids, will be presented, dedicating efforts to develop novel and application-oriented materials for efficient utilization of sustainable solar energy.

  20. Effect of inclusions' distribution on microwave absorbing properties of composites

    NASA Astrophysics Data System (ADS)

    Qin, Siliang; Wang, Qingguo; Qu, Zhaoming

    2013-03-01

    Effect of inclusions' spatial distributions on the permeability and permittivity of composites is studied using the generalized Maxwell-Garnett equations. The result indicates that inclusions' orientation distribution can increase the longitudinal electromagnetic parameters. For inclusions' random and orientation distribution, single and three-layer absorbers are designed and optimized using genetic algorithm. The result shows that under a given absorbing requirement, absorber with inclusions' orientation distribution is lighter and thinner than absorber with inclusions' random distribution.

  1. Method for absorbing an ion from a fluid

    DOEpatents

    Gao, Huizhen; Wang, Yifeng; Bryan, Charles R.

    2007-07-03

    A method for absorbing an ion from a fluid by using dispersing an organic acid into an anion surfactant solution, mixing in a divalent-metal containing compound and a trivalent-metal containing compound and calcining the resulting solid layered double hydroxide product to form an absorbent material and then contacting the absorbent material with an aqueous solution of cations or anions to be absorbed.

  2. Dynamic testing of airplane shock-absorbing struts

    NASA Technical Reports Server (NTRS)

    Langer, P; Thome, W

    1932-01-01

    Measurement of perpendicular impacts of a landing gear with different shock-absorbing struts against the drum testing stand. Tests were made with pneumatic shock absorbers having various degrees of damping, liquid shock absorbers, steel-spring shock absorbers and rigid struts. Falling tests and rolling tests. Maximum impact and gradual reduction of the impacts in number and time in the falling tests. Maximum impact and number of weaker impacts in rolling tests.

  3. An Energy Absorber for the International Space Station

    NASA Technical Reports Server (NTRS)

    Wilkes, Bob; Laurence, Lora

    2000-01-01

    The energy absorber described herein is similar in size and shape to an automotive shock absorber, requiring a constant, high load to compress over the stroke, and self-resetting with a small load. The differences in these loads over the stroke represent the energy absorbed by the device, which is dissipated as friction. This paper describes the evolution of the energy absorber, presents the results of testing performed, and shows the sensitivity of this device to several key design variables.

  4. Absorbed dose dependence of the correction factors for ionization chamber cable irradiation effects.

    PubMed

    Campos, L L; Caldas, L V

    1991-03-01

    A simple method was developed, for possible use by hospital physicists, to evaluate the irradiation effects on cables and connectors during large-radiation-field dosimetry with ionization chambers and to determine correction factors for the used system or geometry. This method was based on the absorbed dose dependence of the correction factor.

  5. Investigation of the Effect of Fixed Absorbers on the Reactivity of PWR Spent Nuclear Fuel for Burnup Credit

    SciTech Connect

    Wagner, John C.; Sanders, Charlotta E.

    2002-08-15

    The effect of fixed absorbers on the reactivity of pressurized water reactor (PWR) spent nuclear fuel (SNF) in support of burnup-credit criticality safety analyses is examined. A fuel assembly burned in conjunction with fixed absorbers may have a higher reactivity for a given burnup than an assembly that has not used fixed absorbers. As a result, guidance on burnup credit, issued by the U.S. Nuclear Regulatory Commission's Spent Fuel Project Office, recommends restricting the use of burnup credit to assemblies that have not used burnable absorbers. This recommendation eliminates a large portion of the currently discharged SNF from loading in burnup credit casks and thus severely limits the practical usefulness of burnup credit. Therefore, data are needed to support the extension of burnup credit to additional SNF. This research investigates the effect of various fixed absorbers, including integral burnable absorbers, burnable poison rods, control rods, and axial power shaping rods, on the reactivity of PWR SNF. Trends in reactivity with relevant parameters (e.g., initial fuel enrichment, burnup and absorber type, exposure, and design) are established, and anticipated reactivity effects are quantified. Where appropriate, recommendations are offered for addressing the reactivity effects of the fixed absorbers in burnup-credit safety analyses.

  6. 40 CFR 65.150 - Absorbers used as control devices.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 16 2014-07-01 2014-07-01 false Absorbers used as control devices. 65... (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Closed Vent Systems, Control Devices, and Routing to a Fuel Gas System or a Process § 65.150 Absorbers used as control devices. (a) Absorber equipment and...

  7. Graphene metamaterials based tunable terahertz absorber: effective surface conductivity approach.

    PubMed

    Andryieuski, Andrei; Lavrinenko, Andrei V

    2013-04-08

    In this paper we present the efficient design of functional thin-film metamaterial devices with the effective surface conductivity approach. As an example, we demonstrate a graphene based perfect absorber. After formulating the requirements to the perfect absorber in terms of surface conductivity we investigate the properties of graphene wire medium and graphene fishnet metamaterials and demonstrate both narrowband and broadband tunable absorbers.

  8. About sound mufflers sound-absorbing panels aircraft engine

    NASA Astrophysics Data System (ADS)

    Dudarev, A. S.; Bulbovich, R. V.; Svirshchev, V. I.

    2016-10-01

    The article provides a formula for calculating the frequency of sound absorbed panel with a perforated wall. And although the sound absorbing structure is a set of resonators Helmholtz, not individual resonators should be considered in acoustic calculations, and all the perforated wall panel. The analysis, showing how the parameters affect the size and sound-absorbing structures in the absorption rate.

  9. 21 CFR 880.5300 - Medical absorbent fiber.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Medical absorbent fiber. 880.5300 Section 880.5300... Devices § 880.5300 Medical absorbent fiber. (a) Identification. A medical absorbent fiber is a device intended for medical purposes that is made from cotton or synthetic fiber in the shape of a ball or a...

  10. 14 CFR 29.475 - Tires and shock absorbers.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Tires and shock absorbers. 29.475 Section... shock absorbers. Unless otherwise prescribed, for each specified landing condition, the tires must be assumed to be in their static position and the shock absorbers to be in their most critical position....

  11. 14 CFR 29.475 - Tires and shock absorbers.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Tires and shock absorbers. 29.475 Section... shock absorbers. Unless otherwise prescribed, for each specified landing condition, the tires must be assumed to be in their static position and the shock absorbers to be in their most critical position....

  12. 14 CFR 29.475 - Tires and shock absorbers.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Tires and shock absorbers. 29.475 Section... shock absorbers. Unless otherwise prescribed, for each specified landing condition, the tires must be assumed to be in their static position and the shock absorbers to be in their most critical position....

  13. 14 CFR 29.475 - Tires and shock absorbers.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tires and shock absorbers. 29.475 Section... shock absorbers. Unless otherwise prescribed, for each specified landing condition, the tires must be assumed to be in their static position and the shock absorbers to be in their most critical position....

  14. 14 CFR 29.475 - Tires and shock absorbers.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Tires and shock absorbers. 29.475 Section... shock absorbers. Unless otherwise prescribed, for each specified landing condition, the tires must be assumed to be in their static position and the shock absorbers to be in their most critical position....

  15. 21 CFR 868.5300 - Carbon dioxide absorbent.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Carbon dioxide absorbent. 868.5300 Section 868...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5300 Carbon dioxide absorbent. (a) Identification. A carbon dioxide absorbent is a device intended for medical purposes that consists of...

  16. 21 CFR 868.5310 - Carbon dioxide absorber.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Carbon dioxide absorber. 868.5310 Section 868.5310...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5310 Carbon dioxide absorber. (a) Identification. A carbon dioxide absorber is a device that is intended for medical purposes and that is used in...

  17. 21 CFR 868.5300 - Carbon dioxide absorbent.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Carbon dioxide absorbent. 868.5300 Section 868...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5300 Carbon dioxide absorbent. (a) Identification. A carbon dioxide absorbent is a device intended for medical purposes that consists of...

  18. 21 CFR 868.5300 - Carbon dioxide absorbent.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Carbon dioxide absorbent. 868.5300 Section 868...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5300 Carbon dioxide absorbent. (a) Identification. A carbon dioxide absorbent is a device intended for medical purposes that consists of...

  19. 21 CFR 868.5310 - Carbon dioxide absorber.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Carbon dioxide absorber. 868.5310 Section 868.5310...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5310 Carbon dioxide absorber. (a) Identification. A carbon dioxide absorber is a device that is intended for medical purposes and that is used in...

  20. 21 CFR 868.5310 - Carbon dioxide absorber.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Carbon dioxide absorber. 868.5310 Section 868.5310...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5310 Carbon dioxide absorber. (a) Identification. A carbon dioxide absorber is a device that is intended for medical purposes and that is used in...

  1. 21 CFR 868.5310 - Carbon dioxide absorber.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Carbon dioxide absorber. 868.5310 Section 868.5310...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5310 Carbon dioxide absorber. (a) Identification. A carbon dioxide absorber is a device that is intended for medical purposes and that is used in...

  2. 21 CFR 868.5300 - Carbon dioxide absorbent.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Carbon dioxide absorbent. 868.5300 Section 868...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5300 Carbon dioxide absorbent. (a) Identification. A carbon dioxide absorbent is a device intended for medical purposes that consists of...

  3. 21 CFR 868.5300 - Carbon dioxide absorbent.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Carbon dioxide absorbent. 868.5300 Section 868...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5300 Carbon dioxide absorbent. (a) Identification. A carbon dioxide absorbent is a device intended for medical purposes that consists of...

  4. 21 CFR 868.5310 - Carbon dioxide absorber.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Carbon dioxide absorber. 868.5310 Section 868.5310...) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5310 Carbon dioxide absorber. (a) Identification. A carbon dioxide absorber is a device that is intended for medical purposes and that is used in...

  5. 21 CFR 878.4755 - Absorbable lung biopsy plug.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Absorbable lung biopsy plug. 878.4755 Section 878...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4755 Absorbable lung biopsy plug. (a) Identification. A preformed (polymerized) absorbable lung biopsy plug is intended to...

  6. [Absorbable coronary stents. New promising technology].

    PubMed

    Erbel, Raimund; Böse, Dirk; Haude, Michael; Kordish, Igor; Churzidze, Sofia; Malyar, Nasser; Konorza, Thomas; Sack, Stefan

    2007-06-01

    Coronary stent implantation started in Germany 20 years ago. In the beginning, the progress was very slow and accelerated 10 years later. Meanwhile, coronary stent implantation is a standard procedure in interventional cardiology. From the beginning of permanent stent implantation, research started to provide temporary stenting of coronary arteries, first with catheter-based systems, later with stent-alone technology. Stents were produced from polymers or metal. The first polymer stent implantation failed except the Igaki-Tamai stent in Japan. Newly developed absorbable polymer stents seem to be very promising, as intravascular ultrasound (IVUS) and optical coherence tomography have demonstrated. Temporary metal stents were developed based on iron and magnesium. Currently, the iron stent is tested in peripheral arteries. The absorbable magnesium stent (Biotronik, Berlin, Germany) was tested in peripheral arteries below the knee and meanwhile in the multicenter international PROGRESS-AMS (Clinical Performance and Angiographic Results of Coronary Stenting with Absorbable Metal Stents) study. The first magnesium stent implantation was performed on July 30, 2004 after extended experimental testing in Essen. The magnesium stent behaved like a bare-metal stent with low recoil of 5-7%. The stent struts were absorbed when tested with IVUS. Stent struts were not visible by fluoroscopy or computed tomography (CT) as well as magnetic resonance imaging (MRI). That means, that the magnesium stent is invisible and therefore CT and MRI can be used for imaging of interventions. Only using micro-CT the stent struts were visible. The absorption process could be demonstrated in a patient 18 days after implantation due to suspected acute coronary syndrome, which was excluded. IVUS showed a nice open lumen. Stent struts were no longer visible, but replaced by tissue indicating the previous stent location. Coronary angiography after 4 months showed an ischemia-driven target lesion

  7. Nuclear DNA Amounts in Macaronesian Angiosperms

    PubMed Central

    SUDA, JAN; KYNCL, TOMÁŠ; FREIOVÁ, RADKA

    2003-01-01

    Nuclear DNA contents for 104 Macaronesian angiosperms, with particular attention on Canary Islands endemics, were analysed using propidium iodide flow cytometry. Prime estimates for more than one‐sixth of the whole Canarian endemic flora (including representatives of 11 endemic genera) were obtained. The resulting 1C DNA values ranged from 0·19 to 7·21 pg for Descurainia bourgeauana and Argyranthemum frutescens, respectively (about 38‐fold difference). The majority of species, however, possessed (very) small genomes, with C‐values <1·6 pg. The tendency towards small nuclear DNA contents and genome sizes was confirmed by comparing average values for Macaronesian and non‐Macaronesian representatives of individual families, genera and major phylogenetic lineages. Our data support the hypothesis that the insular selection pressures in Macaronesia favour small C‐values and genome sizes. Both positive and negative correlations between infrageneric nuclear DNA amount variation and environmental conditions on Tenerife were also found in several genera. PMID:12824074

  8. Health risk assessment of potable water containing small amount of tritium oxide

    NASA Astrophysics Data System (ADS)

    Momot, O. A.; Synzynys, B. I.; Oudalova, A. A.

    2017-01-01

    The problem of groundwater pollution with tritium in a vicinity of radiation-dangerous facilities in Obninsk is considered. The information on the specific activity of tritium in Obninsk water sources is provided. The formula for the calculation of the β-radiation absorbed dose from tritium ingestion is proposed, reflecting the biological behavior of tritium in a human body. To establish the extent of tritium effects on human, the health risk is assessed. It is shown that if the specific activity of tritium in drinking water amounts to 10 Bq/l, the risk of stochastic effects of radiation will not exceed the limit of the individual lifetime risk.

  9. Determination of nanogram amounts of bismuth in rocks by atomic absorption spectrometry with electrothermal atomization

    USGS Publications Warehouse

    Kane, J.S.

    1979-01-01

    Bismuth concentrations as low as 10 ng g-1 in 100-mg samples of geological materials can be determined by atomic absorption spectrometry with electrothermal atomization. After HF-HClO4 decomposition of the sample, bismuth is extracted as the iodide into methyl isobutyl ketone and is then stripped with ethylenediaminetetraacetic acid into the aqueous phase. Aliquots of this solution are pipetted into the graphite furnace and dried, charred, and atomized in an automated sequence. Atomic absorbance at the Bi 223.1-nm line provides a measure of the amount of bismuth present. Results are presented for 14 U.S. Geological Survey standard rocks. ?? 1979.

  10. [Performance of desulfurizing absorbent of roasted navajoite].

    PubMed

    Chen, Fang; Yang, Chun-ping; Gan, Hai-ming; Wu, Ting; Chen, Hai-lin; Chen, Hong; Xu, Ke-hui; Xie, Geng-xin

    2010-04-01

    An innovative flue gas desulfurization (FGD) coupling process was proposed in this study to overcome the problems in wet-type limestone/lime processes which include fouling, clogging, and difficulty of selling the by-products and the problems in traditional process for vanadium extraction from navajoite ore such as excessive consumption of sulfuric acid and emissions of pollutants. The performance of a jet bubbling reactor (JBR) at pilot-scale was evaluated using navajoite ore produced in the process of extracting vanadium pentoxide as desulfurization absorbent. Results showed that navajoite ore slurry achieved better desulfurization performance than limestone slurry. When the inlet flue gas pressure drop was 3.0 kPa, the gas flow was about 2350 m3 x h(-1) and the pH of the navajoite ore slurry was higher than 4.5, the desulfurization efficiency was stable about 90%. The SO2 removal efficiency appeared to increase along with the increasing of absorbent cycle-index. The efficiency of the second circulation was improved 3.5% compared to the first circulation. After an operating duration of 40 minutes, the leaching rate of vanadium pentoxide was about 20%, and reached 60% when the by-products were leached with 5% dilute sulfuric acid for 10 hours. The by-product from this process not only could be used to produce vanadium pentoxide which is a valuable industrial product, but also could significantly overcome the pollution problem existing in the traditional refining process of vanadium pentoxide when navajoite ore is used as the feed material. This FGD process using roasted navajoite slurry as absorbent is environmental sound and cost-effective, and shows the potential for application in the field of flue gas desulfurization as well as hydrometallurgy.

  11. High bioavailable iron maize (Zea mays L.) developed through molecular breeding provides more absorbable iron in vitro and in vivo

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Iron (Fe) deficiency is the most common micronutrient deficiency worldwide. Fe biofortification is a preventative strategy that alleviates Fe deficiency by improving the amount of absorbable Fe in staple crops, such as maize. This approach reaches populations that fortification and supplementation p...

  12. Exposure testing of solar absorber surfaces

    SciTech Connect

    Moore, S.W.

    1986-01-01

    The Los Alamos National Laboratory has been involved in supporting, monitoring and conducting exposure testing of solar materials for approximately ten years. The Laboratory has provided technical monitoring of the IITRI, DSET, Lockheed, and Berry contracts and has operated the Los Alamos exposure Facility for over five years. This report will outline some of the past exposure testing, the testing still in progress, and describe some of the major findings. While this report will primarily emphasize solar absorber surfaces, some of the significant findings relative to advanced glazing will be discussed.

  13. Electrically tunable absorber based on nonstructured graphene

    NASA Astrophysics Data System (ADS)

    Ye, Caiyan; Zhu, Zhihong; Xu, Wei; Yuan, Xiaodong; Qin, Shiqiao

    2015-12-01

    We demonstrate numerically that a tunable absorber with absorption of 99.94% in the far infrared range can be obtained using a nonstructured graphene. The mechanism originates from a nonstructured graphene film supported on a periodical dielectric array that can show Fermi level modulation periodically and produce plasmonic resonances in the far infrared range. The nonstructured graphene can avoid the unexpected edge effects and does not influence the unique properties of graphene, which will be helpful in practice to achieve the unity absorption and facilitate the development of many related applications.

  14. An electromechanical low frequency panel sound absorber.

    PubMed

    Chang, Daoqing; Liu, Bilong; Li, Xiaodong

    2010-08-01

    The sound absorbing properties of a thin micro-perforated plate (MPP) coated with piezoelectric material with shunt damping technology is investigated. First a theoretical model is presented to predict the sound absorption coefficients of a thin plate attached with a piezoelectric patch and electrical circuits. Then the model is extended to analyze the sound absorption for a thin plate with micro perforations and piezoelectric material. Measurements are also carried out in an impedance tube and found to be in good agreements with the theoretical model. The sound absorption of the constructions can be much improved by tuning the electrical circuits.

  15. Piston-rotaxanes as molecular shock absorbers.

    PubMed

    Sevick, E M; Williams, D R M

    2010-04-20

    We describe the thermomechanical response of a new molecular system that behaves as a shock absorber. The system consists of a rodlike rotaxane connected to a piston and tethered to a surface. The response of this system is dominated by the translational entropy of the rotaxane rings and can be calculated exactly. The force laws are contrasted with those for a rigid rod and a polymer. In some cases, the rotaxanes undergo a sudden transition to a tilted state when compressed. These piston-rotaxanes provide a potential motif for the design of a new class of materials with a novel thermomechanical response.

  16. DHCAL with minimal absorber: measurements with positrons

    NASA Astrophysics Data System (ADS)

    Freund, B.; Neubüser, C.; Repond, J.; Schlereth, J.; Xia, L.; Dotti, A.; Grefe, C.; Ivantchenko, V.; Berenguer Antequera, J.; Calvo Alamillo, E.; Fouz, M.-C.; Marin, J.; Puerta-Pelayo, J.; Verdugo, A.; Brianne, E.; Ebrahimi, A.; Gadow, K.; Göttlicher, P.; Günter, C.; Hartbrich, O.; Hermberg, B.; Irles, A.; Krivan, F.; Krüger, K.; Kvasnicka, J.; Lu, S.; Lutz, B.; Morgunov, V.; Provenza, A.; Reinecke, M.; Sefkow, F.; Schuwalow, S.; Tran, H. L.; Garutti, E.; Laurien, S.; Matysek, M.; Ramilli, M.; Schroeder, S.; Bilki, B.; Norbeck, E.; Northacker, D.; Onel, Y.; Cvach, J.; Gallus, P.; Havranek, M.; Janata, M.; Kovalcuk, M.; Kvasnicka, J.; Lednicky, D.; Marcisovsky, M.; Polak, I.; Popule, J.; Tomasek, L.; Tomasek, M.; Sicho, P.; Smolik, J.; Vrba, V.; Zalesak, J.; van Doren, B.; Wilson, G. W.; Kawagoe, K.; Hirai, H.; Sudo, Y.; Suehara, T.; Sumida, H.; Takada, S.; Tomita, T.; Yoshioka, T.; Bilokin, S.; Bonis, J.; Cornebise, P.; Pöschl, R.; Richard, F.; Thiebault, A.; Zerwas, D.; Hostachy, J.-Y.; Morin, L.; Besson, D.; Chadeeva, M.; Danilov, M.; Markin, O.; Popova, E.; Gabriel, M.; Goecke, P.; Kiesling, C.; van der Kolk, N.; Simon, F.; Szalay, M.; Corriveau, F.; Blazey, G. C.; Dyshkant, A.; Francis, K.; Zutshi, V.; Kotera, K.; Ono, H.; Takeshita, T.; Ieki, S.; Kamiya, Y.; Ootani, W.; Shibata, N.; Jeans, D.; Komamiya, S.; Nakanishi, H.

    2016-05-01

    In special tests, the active layers of the CALICE Digital Hadron Calorimeter prototype, the DHCAL, were exposed to low energy particle beams, without being interleaved by absorber plates. The thickness of each layer corresponded approximately to 0.29 radiation lengths or 0.034 nuclear interaction lengths, defined mostly by the copper and steel skins of the detector cassettes. This paper reports on measurements performed with this device in the Fermilab test beam with positrons in the energy range of 1 to 10 GeV. The measurements are compared to simulations based on GEANT4 and a standalone program to emulate the detailed response of the active elements.

  17. Absorbing boundary conditions for exterior problems

    NASA Technical Reports Server (NTRS)

    Hariharan, S. I.

    1985-01-01

    Elliptic and hyperbolic problems in unbounded regions are considered. These problems, when one wants to solve them numerically, have the difficulty of prescribing boundary conditions at infinity. Computationally, one needs a finite region in which to solve these problems. The corresponding conditions at infinity imposed on the finite distance boundaries should dictate the boundary condition at infinity and be accurate with respect to the interior numerical scheme. Such boundary conditions are commonly referred to as absorbing boundary conditions. A treatment is given of these boundary conditions for wave-like equations.

  18. Highly absorbing ARC for DUV lithography

    NASA Astrophysics Data System (ADS)

    Pavelchek, Edward K.; Meador, James D.; Guerrero, Douglas J.; Lamb, James E., III; Kache, Ajit; doCanto, Manuel; Adams, Timothy G.; Stark, David R.; Miller, Daniel A.

    1996-06-01

    The properties of a new anti-reflective coating for 248 nm lithography are described. It is formed by thermally cross-linking a spin-on organic coating, and has an absorbance greater than 12/micrometers. It is compatible with UVIIHS and APEX-E photoresists. Thin films (less than 600 angstrom over silicon substrates) are found to completely suppress standing waves, to reduce EO swing curves to less than 3%, and to offer good CD control over typical field oxide topography. The etch rate was found to be comparable to that of the APEX-E photoresist.

  19. A novel broadband waterborne acoustic absorber

    NASA Astrophysics Data System (ADS)

    Wang, Changxian; Wen, Weibin; Huang, Yixing; Chen, Mingji; Lei, Hongshuai; Fang, Daining

    2016-07-01

    In this paper, we extended the ray tracing theory in polar coordinate system, and originally proposed the Snell-Descartes law in polar coordinates. Based on these theories, a novel broadband waterborne acoustic absorber device was proposed. This device is designed with gradient-distributing materials along radius, which makes the incidence acoustic wave ray warps. The echo reduction effects of this device were investigated by finite element analysis, and the numerical results show that the reflectivity of acoustic wave for the new device is lower than that of homogenous and Alberich layers in almost all frequency 0-30 kHz at the same loss factor.

  20. Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

    NASA Astrophysics Data System (ADS)

    Lejnieks, J. E.; Kajaks, J. A.; Reihmane, S. A.

    2005-07-01

    The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.

  1. What Determines the Amount Students Borrow? Revisiting the Crisis-Convenience Debate

    ERIC Educational Resources Information Center

    Hart, Natala K.; Mustafa, Shoumi

    2008-01-01

    Recent studies have questioned the wisdom in blaming college costs for the escalation of student loans. It would appear that less affluent students borrow large amounts because inexpensive subsidized loans are available. This study attempted to verify the claim, estimating a model of the amount of loan received by students as a function of net…

  2. Insight into the Nonlinear Absorbance of Two Related Series of Two-Photon Absorbing Chromophores (Postprint)

    DTIC Science & Technology

    2007-01-01

    Reinhardt, B. A. Opt. Lett. 1995, 20, 1524. (f) Larson, E . J.; Friesen , L. A.; Johnson, C. K. Chem. Phys. Lett. 1997, 265, 161. (g) Albota, M.; Beljonne, D...62102F 5d. PROJECT NUMBER 4348 5e. TASK NUMBER RG 6. AUTHOR(S) Joy E . Rogers (UES, Inc.) Jonathan E . Slagle (AT&T Government Solutions) Daniel G...Insight into the Nonlinear Absorbance of Two Related Series of Two-Photon Absorbing Chromophores Joy E . Rogers,*,†,‡ Jonathan E . Slagle,†,§ Daniel G

  3. Optimum Tolerance Design Using Component-Amount and Mixture-Amount Experiments

    SciTech Connect

    Piepel, Gregory F.; Ozler, Cenk; Sehirlioglu, Ali Kemal

    2013-08-01

    One type of tolerance design problem involves optimizing component and assembly tolerances to minimize the total cost (sum of manufacturing cost and quality loss). Previous literature recommended using traditional response surface (RS) designs and models to solve this type of tolerance design problem. In this article, component-amount (CA) and mixture-amount (MA) approaches are proposed as more appropriate for solving this type of tolerance design problem. The advantages of the CA and MA approaches over the RS approach are discussed. Reasons for choosing between the CA and MA approaches are also discussed. The CA and MA approaches (experimental design, response modeling, and optimization) are illustrated using real examples.

  4. Improvement of Mishchenko's T-matrix code for absorbing particles

    NASA Astrophysics Data System (ADS)

    Moroz, Alexander

    2005-06-01

    The use of Gaussian elimination with backsubstitution for matrix inversion in scattering theories is discussed. Within the framework of the T-matrix method (the state-of-the-art code by Mishchenko is freely available at http://www.giss.nasa.gov/~crmim), it is shown that the domain of applicability of Mishchenko's FORTRAN 77 (F77) code can be substantially expanded in the direction of strongly absorbing particles where the current code fails to converge. Such an extension is especially important if the code is to be used in nanoplasmonic or nanophotonic applications involving metallic particles. At the same time, convergence can also be achieved for large nonabsorbing particles, in which case the non-Numerical Algorithms Group option of Mishchenko's code diverges. Computer F77 implementation of Mishchenko's code supplemented with Gaussian elimination with backsubstitution is freely available at http://www.wave-scattering.com.

  5. Measurement of EUV absorber and resist CD using spectroscopic ellipsometer

    NASA Astrophysics Data System (ADS)

    Lee, Kyung M.; Tavassoli, Malahat; Yan, Pei-yang; Zhang, Guojing

    2013-09-01

    Evaluation of lithography process or stepper involves very large quantity of CD measurements and measurement time. In this paper, we report on an application of Scatterometry based metrology for evaluation of EUV photomask lithography. Measurements were made on mask level with Ellipsometric scatterometer for develop-check CD (DCCD) and final check CD (FCCD). Calculation of scatterometer profile information was performed with in-situ library-based rigorous coupled wave analysis (RCWA) method. We characterized the CD uniformity (CDU) and metal film thickness uniformity. OCD results show that high precision CD measurement EUV absorber and resist is possible with this method. A series of simulations were also performed to investigate the feasibility of Ellipsometric scatterometry for various pitches/line CD sizes, down to 11nm half-pitch at 1x magnification. The data showed that Scatterometry provides a nondestructive and faster mean of characterizing mask CD performance for various EUV process generations.

  6. Optical fibre-coupled cryogenic radiometer with carbon nanotube absorber

    NASA Astrophysics Data System (ADS)

    Livigni, David J.; Tomlin, Nathan A.; Cromer, Christopher L.; Lehman, John H.

    2012-04-01

    A cryogenic radiometer was constructed for direct-substitution optical-fibre power measurements. The cavity is intended to operate at the 3 K temperature stage of a dilution refrigerator or 4.2 K stage of a liquid cryostat. The optical fibre is removable for characterization. The cavity features micromachined silicon centring rings to thermally isolate the optical fibre as well as an absorber made from micromachined silicon on which vertically aligned carbon nanotubes were grown. Measurements of electrical substitution, optical absorption and temperature change indicate that the radiometer is capable of measuring a power level of 10 nW with approximate responsivity of 155 nW K-1 and 1/e time constant of 13 min. An inequivalence between optical and electrical power of approximately 10% was found, but the difference was largely attributable to unaccounted losses in the optical fibre.

  7. Improvement of Mishchenko's T-matrix code for absorbing particles.

    PubMed

    Moroz, Alexander

    2005-06-10

    The use of Gaussian elimination with backsubstitution for matrix inversion in scattering theories is discussed. Within the framework of the T-matrix method (the state-of-the-art code by Mishchenko is freely available at http://www.giss.nasa.gov/-crmim), it is shown that the domain of applicability of Mishchenko's FORTRAN 77 (F77) code can be substantially expanded in the direction of strongly absorbing particles where the current code fails to converge. Such an extension is especially important if the code is to be used in nanoplasmonic or nanophotonic applications involving metallic particles. At the same time, convergence can also be achieved for large nonabsorbing particles, in which case the non-Numerical Algorithms Group option of Mishchenko's code diverges. Computer F77 implementation of Mishchenko's code supplemented with Gaussian elimination with backsubstitution is freely available at http://www.wave-scattering.com.

  8. Improved estimates of the radiation absorbed dose to the urinary bladder wall.

    PubMed

    Andersson, Martin; Minarik, David; Johansson, Lennart; Mattsson, Sören; Leide-Svegborn, Sigrid

    2014-05-07

    Specific absorbed fractions (SAFs) have been calculated as a function of the content in the urinary bladder in order to allow more realistic calculations of the absorbed dose to the bladder wall. The SAFs were calculated using the urinary bladder anatomy from the ICRP male and female adult reference computational phantoms. The urinary bladder and its content were approximated by a sphere with a wall of constant mass, where the thickness of the wall depended on the amount of urine in the bladder. SAFs were calculated for males and females with 17 different urinary bladder volumes from 10 to 800 mL, using the Monte Carlo computer program MCNP5, at 25 energies of mono-energetic photons and electrons ranging from 10 KeV to 10 MeV. The decay was assumed to be homogeneously distributed in the urinary bladder content and the urinary bladder wall, and the mean absorbed dose to the urinary bladder wall was calculated. The Monte Carlo simulations were validated against measurements made with thermoluminescent dosimeters. The SAFs obtained for a urine volume of 200 mL were compared to the values calculated for the urinary bladder wall using the adult reference computational phantoms. The mean absorbed dose to the urinary wall from (18)F-FDG was found to be 77 µGy/MBq formales and 86 µGy/MBq for females, while for (99m)Tc-DTPA the mean absorbed doses were 80 µGy/MBq for males and 86 µGy/MBq for females. Compared to calculations using a constant value of the SAF from the adult reference computational phantoms, the mean absorbed doses to the bladder wall were 60% higher for (18)F-FDG and 30% higher for (99m)Tc-DTPA using the new SAFs.

  9. Competing Atmospheric and Surface-Driven Impacts of Absorbing Aerosols on the East Asian Summer Monsoon

    NASA Astrophysics Data System (ADS)

    Persad, G.; Paynter, D.; Ming, Y.; Ramaswamy, V.

    2015-12-01

    Absorbing aerosols, by attenuating shortwave radiation within the atmosphere and reemitting it as longwave radiation, redistribute energy both vertically within the surface-atmosphere column and horizontally between polluted and unpolluted regions. East Asia has the largest concentrations of anthropogenic absorbing aerosols globally, and these, along with the region's scattering aerosols, have both reduced the amount of solar radiation reaching the Earth's surface regionally ("solar dimming") and increased shortwave absorption within the atmosphere, particularly during the peak months of the East Asian Summer Monsoon (EASM). We here analyze how atmospheric absorption and surface solar dimming compete in driving the response of EASM circulation to anthropogenic absorbing aerosols, which dominates, and why—issues of particular importance for predicting how the EASM will respond to projected changes in absorbing and scattering aerosol emissions in the future. We probe these questions in a state-of-the-art general circulation model (GCM) using a combination of realistic and idealized aerosol perturbations that allow us to analyze the relative influence of absorbing aerosols' atmospheric and surface-driven impacts on EASM circulation. In combination, our results make clear that, although absorption-driven dimming has a less detrimental effect on EASM circulation than purely scattering-driven dimming, aerosol absorption is still a net impairment to EASM strength when both its atmospheric and surface effects are considered. Because atmospheric heating is not efficiently conveyed to the surface, the surface dimming and associated cooling from even a pure absorber is sufficient to counteract its atmospheric heating, resulting in a net reduction in EASM strength. These findings elevate the current understanding of the impacts of aerosol absorption on the EASM, improving our ability to diagnose EASM responses to current and future regional changes in aerosol emissions.

  10. Generalized contact process with two symmetric absorbing states in two dimensions.

    PubMed

    Lee, Man Young; Vojta, Thomas

    2011-01-01

    We explore the two-dimensional generalized contact process with two absorbing states by means of large-scale Monte-Carlo simulations. In part of the phase diagram, an infinitesimal creation rate of active sites between inactive domains is sufficient to take the system from the inactive phase to the active phase. The system, therefore, displays two different nonequilibrium phase transitions. The critical behavior of the generic transition is compatible with the generalized voter universality class, implying that the symmetry-breaking and absorbing transitions coincide. In contrast, the transition at zero domain-boundary activation rate is not critical.

  11. Voltage-dependent absorbance change of carotenoids in halophilic archaebacteria.

    PubMed

    Seki, S I; Sasabe, H; Tomioka, H

    1996-10-02

    Membrane vesicles of wild-type Halobacterium sp. mex strain show a wavy absorbance change which has not been so far reported in halophilic archaebacteria. A white mutant strain lacking carotenoids did not show the wavy absorbance change. The wavy absorbance change in the range of 440-590 nm was induced by a red flash (600-640 nm), which photoexcited electrogenic ion pumps, mex bacteriorhodopsin and mex halorhodopsin but not carotenoids. The wavy change was also caused by K+ diffusion potentials without light. These results suggest that the wavy absorbance change in the membrane vesicles is the voltage-dependent absorbance change of the carotenoids.

  12. Impacts of Snow Darkening by Absorbing Aerosols on Eurasian Climate

    NASA Technical Reports Server (NTRS)

    Kim, Kyu-Myong; Lau, William K M.; Yasunari, Teppei J.; Kim, Maeng-Ki; Koster, Randal D.

    2016-01-01

    The deposition of absorbing aerosols on snow surfaces reduces snow-albedo and allows snowpack to absorb more sunlight. This so-called snow darkening effect (SDE) accelerates snow melting and leads to surface warming in spring. To examine the impact of SDE on weather and climate during late spring and early summer, two sets of NASA GEOS-5 model simulations with and without SDE are conducted. Results show that SDE-induced surface heating is particularly pronounced in Eurasian regions where significant depositions of dust transported from the North African deserts, and black carbon from biomass burning from Asia and Europe occur. In these regions, the surface heating due to SDE increases surface skin temperature by 3-6 degrees Kelvin near the snowline in spring. Surface energy budget analysis indicates that SDE-induced excess heating is associated with a large increase in surface evaporation, subsequently leading to a significant reduction in soil moisture, and increased risks of drought and heat waves in late spring to early summer. Overall, we find that rainfall deficit combined with SDE-induced dry soil in spring provide favorable condition for summertime heat waves over large regions of Eurasia. Increased frequency of summer heat waves with SDE and the region of maximum increase in heat-wave frequency are found along the snow line, providing evidence that early snowmelt by SDE may increase the risks of extreme summer heat wave. Our results suggest that climate models that do not include SDE may significantly underestimate the effect of global warming over extra-tropical continental regions.

  13. Fabrication of an Absorber-Coupled MKID Detector

    NASA Technical Reports Server (NTRS)

    Brown, Ari; Hsieh, Wen-Ting; Moseley, Samuel; Stevenson, Thomas; U-Yen, Kongpop; Wollack, Edward

    2012-01-01

    Absorber-coupled microwave kinetic inductance detector (MKID) arrays were developed for submillimeter and far-infrared astronomy. These sensors comprise arrays of lambda/2 stepped microwave impedance resonators patterned on a 1.5-mm-thick silicon membrane, which is optimized for optical coupling. The detector elements are supported on a 380-mm-thick micro-machined silicon wafer. The resonators consist of parallel plate aluminum transmission lines coupled to low-impedance Nb microstrip traces of variable length, which set the resonant frequency of each resonator. This allows for multiplexed microwave readout and, consequently, good spatial discrimination between pixels in the array. The transmission lines simultaneously act to absorb optical power and employ an appropriate surface impedance and effective filling fraction. The fabrication techniques demonstrate high-fabrication yield of MKID arrays on large, single-crystal membranes and sub-micron front-to-back alignment of the micro strip circuit. An MKID is a detector that operates upon the principle that a superconducting material s kinetic inductance and surface resistance will change in response to being exposed to radiation with a power density sufficient to break its Cooper pairs. When integrated as part of a resonant circuit, the change in surface impedance will result in a shift in its resonance frequency and a decrease of its quality factor. In this approach, incident power creates quasiparticles inside a superconducting resonator, which is configured to match the impedance of free space in order to absorb the radiation being detected. For this reason MKIDs are attractive for use in large-format focal plane arrays, because they are easily multiplexed in the frequency domain and their fabrication is straightforward. The fabrication process can be summarized in seven steps: (1) Alignment marks are lithographically patterned and etched all the way through a silicon on insulator (SOI) wafer, which consists of a

  14. Mapping liquid distribution in absorbent incontinence products.

    PubMed

    Landeryou, M A; Yerworth, R J; Cottenden, A M

    2003-01-01

    This paper reviews methods available for mapping the distribution of fluid in incontinence pad materials to assist with evaluating existing products and developing new ones, and to provide data for building and validating predictive models. Specifically, the following technologies are considered and their strengths and limitations described: discrete sensors based on conductance, temperature or optical measurements, optical imaging, gravimetric methods, X-ray imaging and magnetic resonance imaging. It is suggested that the ideal method would enable fluid distribution to be mapped in three dimensions with good spatial and time resolution in single materials and composite structures of simple and complex geometries under static and dynamic mechanical loading. It would also allow liquid to be mapped in products when worn by users. It is concluded that, although each existing method meets some of these requirements, and each requirement is met, at least reasonably well, by at least one method, improved techniques are needed. The particular need for methods that can provide some measurement of liquid saturation within absorbent products, both in the laboratory and in real use, is highlighted. In many cases, simple methods used appropriately are sufficient to elicit the important aspects of liquid transport and storage within absorbent products.

  15. Configurable metamaterial absorber with pseudo wideband spectrum.

    PubMed

    Zhu, Weiren; Huang, Yongjun; Rukhlenko, Ivan D; Wen, Guangjun; Premaratne, Malin

    2012-03-12

    Metamaterials attain their behavior due to resonant interactions among their subwavelength components and thus show specific designer features only in a very narrow frequency band. There is no simple way to dynamically increase the operating bandwidth of a narrowband metamaterial, but it may be possible to change its central frequency, shifting the spectral response to a new frequency range. In this paper, we propose and experimentally demonstrate a metamaterial absorber that can shift its central operating frequency by using mechanical means. The shift is achieved by varying the gap between the metamaterial and an auxiliary dielectric slab parallel to its surface. We also show that it is possible to create multiple absorption peaks by adjusting the size and/or shape of the dielectric slab, and to shift them by moving the slab relative to the metamaterial. Specifically, using numerical simulations we design a microwave metamaterial absorber and experimentally demonstrate that its central frequency can be set anywhere in a 1.6 GHz frequency range. The proposed configuration is simple and easy to make, and may be readily extended to THz frequencies.

  16. Spacesuit Evaporator-Absorber-Radiator (SEAR)

    NASA Technical Reports Server (NTRS)

    Hodgson, Ed; Izenson, Mike; Chan, Weibo; Bue, Grant C.

    2012-01-01

    For decades advanced spacesuit developers have pursued a regenerable, robust nonventing system for heat rejection. Toward this end, this paper investigates linking together two previously developed technologies, namely NASA s Spacesuit Water Membrane Evaporator (SWME), and Creare s Lithium Chloride Absorber Radiator (LCAR). Heat from a liquid cooled garment is transported to SWME that provides cooling through evaporation. This water vapor is then captured by solid LiCl in the LCAR with a high enthalpy of absorption, resulting in sufficient temperature lift to reject heat to space by radiation. After the sortie, the LCAR would be heated up and dried in a regenerator to drive off and recover the absorbed evaporant. A engineering development prototype was built and tested in vacuum conditions at a sink temperature of 250 K. The LCAR was able to stably reject 75 W over a 7-hour period. A conceptual design of a full-scale radiator is proposed. Excess heat rejection above 240 W would be accomplished through venting of the evaporant. Loop closure rates were predicted for various exploration environment scenarios.

  17. Possible Quantum Absorber Effects in Cortical Synchronization

    NASA Astrophysics Data System (ADS)

    Kämpf, Uwe

    The Wheeler-Feynman transactional "absorber" approach was proposed originally to account for anomalous resonance coupling between spatio-temporally distant measurement partners in entangled quantum states of so-called Einstein-Podolsky-Rosen paradoxes, e.g. of spatio-temporal non-locality, quantum teleportation, etc. Applied to quantum brain dynamics, however, this view provides an anticipative resonance coupling model for aspects of cortical synchronization and recurrent visual action control. It is proposed to consider the registered activation patterns of neuronal loops in so-called synfire chains not as a result of retarded brain communication processes, but rather as surface effects of a system of standing waves generated in the depth of visual processing. According to this view, they arise from a counterbalance between the actual input's delayed bottom-up data streams and top-down recurrent information-processing of advanced anticipative signals in a Wheeler-Feynman-type absorber mode. In the framework of a "time-loop" model, findings about mirror neurons in the brain cortex are suggested to be at least partially associated with temporal rather than spatial mirror functions of visual processing, similar to phase conjugate adaptive resonance-coupling in nonlinear optics.

  18. Fabrication of THz Sensor with Metamaterial Absorber

    NASA Astrophysics Data System (ADS)

    Gonzalez, Hugo; Alves, Fabio; Karunasiri, Gamani

    The terahertz (THz) portion of the electromagnetic spectrum (0.1-10 THz) has not been fully utilized due to the lack of sensitive detectors. Real-time imaging in this spectral range has been demonstrated using uncooled infrared microbolometer cameras and external illumination provided by quantum cascade laser (QCL) based THz sources. However, the microbolometer pixels in the cameras have not been optimized to achieve high sensitivity in THz frequencies. Recently, we have developed a highly sensitive micromechanical THz sensor employing bi-material effect with an integrated metamaterial absorber tuned to the THz frequency of interest. The use of bi-material structures causes deflection on the sensor to as the absorbed THz radiation increases its temperature, which can be monitored optically by reflecting a light beam. This approach eliminates the integration of readout electronics needed in microbolometers. The absorption of THz by metamaterial can be tailored by controlling geometrical parameters. The sensors can be fabricated using conventional microelectronic materials and incorporated into pixels to form focal plane arrays (FPAs). In this presentation, characterization and readout of a THz sensor with integrated metamaterial structure will be described. Supported by DoD.

  19. Wave energy extraction by coupled resonant absorbers.

    PubMed

    Evans, D V; Porter, R

    2012-01-28

    In this article, a range of problems and theories will be introduced that will build towards a new wave energy converter (WEC) concept, with the acronym 'ROTA' standing for resonant over-topping absorber. First, classical results for wave power absorption for WECs constrained to operate in a single degree of freedom will be reviewed and the role of resonance in their operation highlighted. Emphasis will then be placed on how the introduction of further resonances can improve power take-off characteristics by extending the range of frequencies over which the efficiency is close to a theoretical maximum. Methods for doing this in different types of WECs will be demonstrated. Coupled resonant absorbers achieve this by connecting a WEC device equipped with its own resonance (determined from a hydrodynamic analysis) to a new system having separate mass/spring/damper characteristics. It is shown that a coupled resonant effect can be realized by inserting a water tank into a WEC, and this idea forms the basis of the ROTA device. In essence, the idea is to exploit the coupling between the natural sloshing frequencies of the water in the internal tank and the natural resonance of a submerged buoyant circular cylinder device that is tethered to the sea floor, allowing a rotary motion about its axis of attachment.

  20. Erbium concentration dependent absorbance in tellurite glass

    SciTech Connect

    Sazali, E. S. Rohani, M. S. Sahar, M. R. Arifin, R. Ghoshal, S. K. Hamzah, K.

    2014-09-25

    Enhancing the optical absorption cross-section in topically important rare earth doped tellurite glasses is challenging for photonic devices. Controlled synthesis and detailed characterizations of the optical properties of these glasses are important for the optimization. The influence of varying concentration of Er{sup 3+} ions on the absorbance characteristics of lead tellurite glasses synthesized via melt-quenching technique are investigated. The UV-Vis absorption spectra exhibits six prominent peaks centered at 490, 526, 652, 800, 982 and 1520 nm ascribed to the transitions in erbium ion from the ground state to the excited states {sup 4}F{sub 7/2}, {sup 2}H{sub 11/2}, {sup 4}F{sub 9/2}, {sup 4}I{sub 9/2}, {sup 2}H{sub 11/2} and {sup 4}I{sub 13/2}, respectively. The results are analyzed by means of optical band gap E{sub g} and Urbach energy E{sub u}. The values of the energy band gap are found decreased from 2.82 to 2.51 eV and the Urbach energy increased from 0.15 to 0.24 eV with the increase of the Er{sub 2}O{sub 3} concentration from 0 to 1.5 mol%. The excellent absorbance of the prepared tellurite glasses makes them suitable for fabricating solid state lasers.

  1. 24 CFR 576.45 - Reallocation of grant amounts; returned or unused amounts.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... DEVELOPMENT, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT COMMUNITY FACILITIES EMERGENCY SHELTER GRANTS PROGRAM... or unused amounts. (a) General. From time to time, HUD will reallocate emergency shelter grant... and Shelter Program administered by the Federal Emergency Management Agency, as a resource to...

  2. 24 CFR 576.45 - Reallocation of grant amounts; returned or unused amounts.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... DEVELOPMENT, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT COMMUNITY FACILITIES EMERGENCY SHELTER GRANTS PROGRAM... or unused amounts. (a) General. From time to time, HUD will reallocate emergency shelter grant... and Shelter Program administered by the Federal Emergency Management Agency, as a resource to...

  3. 76 FR 59138 - Medicare Program; Medicare Appeals; Adjustment to the Amount in Controversy Threshold Amounts for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-23

    ..., respectively, for Medicare Part A and Part B appeals. Section 940 of the Medicare Prescription Drug... the consumer price index for all urban consumers (U.S. city average) for July 2003 to July of the year... (Prescription Drug Plan) Appeals The annually adjusted AIC threshold amounts for ALJ hearings and...

  4. Determination of decay coefficients for combustors with acoustic absorbers

    NASA Technical Reports Server (NTRS)

    Mitchell, C. E.; Espander, W. R.; Baer, M. R.

    1972-01-01

    An analytical technique for the calculation of linear decay coefficients in combustors with acoustic absorbers is presented. Tuned circumferential slot acoustic absorbers were designed for the first three transverse modes of oscillation, and decay coefficients for these absorbers were found as a function of backing distance for seven different chamber configurations. The effectiveness of the absorbers for off-design values of the combustion response and acoustic mode is also investigated. Results indicate that for tuned absorbers the decay coefficient increases approximately as the cube of the backing distance. For most off-design situations the absorber still provides a damping effect. However, if an absorber designed for some higher mode of oscillation is used to damp lower mode oscillations, a driving effect is frequently found.

  5. Container and method for absorbing and reducing hydrogen concentration

    DOEpatents

    Wicks, George G.; Lee, Myung W.; Heung, Leung K.

    2001-01-01

    A method for absorbing hydrogen from an enclosed environment comprising providing a vessel; providing a hydrogen storage composition in communication with a vessel, the hydrogen storage composition further comprising a matrix defining a pore size which permits the passage of hydrogen gas while blocking the passage of gaseous poisons; placing a material within the vessel, the material evolving hydrogen gas; sealing the vessel; and absorbing the hydrogen gas released into the vessel by the hydrogen storage composition. A container for absorbing evolved hydrogen gas comprising: a vessel having an interior and adapted for receiving materials which release hydrogen gas; a hydrogen absorbing composition in communication with the interior, the composition defining a matrix surrounding a hydrogen absorber, the matrix permitting the passage of hydrogen gas while excluding gaseous poisons; wherein, when the vessel is sealed, hydrogen gas, which is released into the vessel interior, is absorbed by the hydrogen absorbing composition.

  6. Composite neutron absorbing coatings for nuclear criticality control

    DOEpatents

    Wright, Richard N.; Swank, W. David; Mizia, Ronald E.

    2005-07-19

    Thermal neutron absorbing composite coating materials and methods of applying such coating materials to spent nuclear fuel storage systems are provided. A composite neutron absorbing coating applied to a substrate surface includes a neutron absorbing layer overlying at least a portion of the substrate surface, and a corrosion resistant top coat layer overlying at least a portion of the neutron absorbing layer. An optional bond coat layer can be formed on the substrate surface prior to forming the neutron absorbing layer. The neutron absorbing layer can include a neutron absorbing material, such as gadolinium oxide or gadolinium phosphate, dispersed in a metal alloy matrix. The coating layers may be formed by a plasma spray process or a high velocity oxygen fuel process.

  7. A shock absorber model for structure-borne noise analyses

    NASA Astrophysics Data System (ADS)

    Benaziz, Marouane; Nacivet, Samuel; Thouverez, Fabrice

    2015-08-01

    Shock absorbers are often responsible for undesirable structure-borne noise in cars. The early numerical prediction of this noise in the automobile development process can save time and money and yet remains a challenge for industry. In this paper, a new approach to predicting shock absorber structure-borne noise is proposed; it consists in modelling the shock absorber and including the main nonlinear phenomena responsible for discontinuities in the response. The model set forth herein features: compressible fluid behaviour, nonlinear flow rate-pressure relations, valve mechanical equations and rubber mounts. The piston, base valve and complete shock absorber model are compared with experimental results. Sensitivity of the shock absorber response is evaluated and the most important parameters are classified. The response envelope is also computed. This shock absorber model is able to accurately reproduce local nonlinear phenomena and improves our state of knowledge on potential noise sources within the shock absorber.

  8. Absorber Alignment Measurement Tool for Solar Parabolic Trough Collectors: Preprint

    SciTech Connect

    Stynes, J. K.; Ihas, B.

    2012-04-01

    As we pursue efforts to lower the capital and installation costs of parabolic trough solar collectors, it is essential to maintain high optical performance. While there are many optical tools available to measure the reflector slope errors of parabolic trough solar collectors, there are few tools to measure the absorber alignment. A new method is presented here to measure the absorber alignment in two dimensions to within 0.5 cm. The absorber alignment is measured using a digital camera and four photogrammetric targets. Physical contact with the receiver absorber or glass is not necessary. The alignment of the absorber is measured along its full length so that sagging of the absorber can be quantified with this technique. The resulting absorber alignment measurement provides critical information required to accurately determine the intercept factor of a collector.

  9. 46 CFR 308.303 - Amounts insured under interim binder.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... INSURANCE Second Seamen's War Risk Insurance § 308.303 Amounts insured under interim binder. The amounts insured are the amounts specified in the Second Seamen's War Risk Policy (1955) or as modified by...

  10. 46 CFR 308.303 - Amounts insured under interim binder.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... INSURANCE Second Seamen's War Risk Insurance § 308.303 Amounts insured under interim binder. The amounts insured are the amounts specified in the Second Seamen's War Risk Policy (1955) or as modified by...

  11. 46 CFR 308.303 - Amounts insured under interim binder.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... INSURANCE Second Seamen's War Risk Insurance § 308.303 Amounts insured under interim binder. The amounts insured are the amounts specified in the Second Seamen's War Risk Policy (1955) or as modified by...

  12. 46 CFR 308.303 - Amounts insured under interim binder.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... INSURANCE Second Seamen's War Risk Insurance § 308.303 Amounts insured under interim binder. The amounts insured are the amounts specified in the Second Seamen's War Risk Policy (1955) or as modified by...

  13. Dependence of residual rotation measure on intervening Mg II absorbers at cosmic distances

    NASA Astrophysics Data System (ADS)

    Joshi, Ravi; Chand, Hum

    2013-10-01

    We investigate the dependence of residual rotation measure (RRM) on intervening absorption systems at cosmic distances by using a large sample of 539 Sloan Digital Sky survey quasars in conjunction with the available rotation measure catalogue at around 21 cm wavelength. We found an excess extragalactic contribution in the standard deviation of an observed RRM (σrrm) of about 8.11 ± 4.83 rad m-2 in our sample with an intervening Mg II absorber as compared to the sample without an Mg II absorber. Our results suggest that intervening absorbers could contribute to the enhancement of RRM at around 21 cm wavelength, as was found earlier for rotation measure measurements at around 6 cm wavelength.

  14. Experimental study of acoustic radiation force of an ultrasound beam on absorbing and scattering objects

    NASA Astrophysics Data System (ADS)

    Nikolaeva, Anastasiia V.; Kryzhanovsky, Maxim A.; Tsysar, Sergey A.; Kreider, Wayne; Sapozhnikov, Oleg A.

    2015-10-01

    Acoustic radiation force is a nonlinear acoustic effect caused by the transfer of wave momentum to absorbing or scattering objects. This phenomenon is exploited in modern ultrasound metrology for measurement of the acoustic power radiated by a source and is used for both therapeutic and diagnostic sources in medical applications. To calculate radiation force an acoustic hologram can be used in conjunction with analytical expressions based on the angular spectrum of the measured field. The results of an experimental investigation of radiation forces in two different cases are presented in this paper. In one case, the radiation force of an obliquely incident ultrasound beam on a large absorber (which completely absorbs the beam) is considered. The second case concerns measurement of the radiation force on a spherical target that is small compared to the beam diameter.

  15. Experimental Study of Acoustic Radiation Force of an Ultrasound Beam on Absorbing and Scattering Objects

    PubMed Central

    Nikolaeva, Anastasiia V.; Kryzhanovsky, Maxim A.; Tsysar, Sergey A.; Kreider, Wayne; Sapozhnikov, Oleg A.

    2016-01-01

    Acoustic radiation force is a nonlinear acoustic effect caused by the transfer of wave momentum to absorbing or scattering objects. This phenomenon is exploited in modern ultrasound metrology for measurement of the acoustic power radiated by a source and is used for both therapeutic and diagnostic sources in medical applications. To calculate radiation force an acoustic hologram can be used in conjunction with analytical expressions based on the angular spectrum of the measured field. The results of an experimental investigation of radiation forces in two different cases are presented in this paper. In one case, the radiation force of an obliquely incident ultrasound beam on a large absorber (which completely absorbs the beam) is considered. The second case concerns measurement of the radiation force on a spherical target that is small compared to the beam diameter. PMID:27147775

  16. Experimental study of acoustic radiation force of an ultrasound beam on absorbing and scattering objects

    SciTech Connect

    Nikolaeva, Anastasiia V. Kryzhanovsky, Maxim A.; Tsysar, Sergey A.; Kreider, Wayne; Sapozhnikov, Oleg A.

    2015-10-28

    Acoustic radiation force is a nonlinear acoustic effect caused by the transfer of wave momentum to absorbing or scattering objects. This phenomenon is exploited in modern ultrasound metrology for measurement of the acoustic power radiated by a source and is used for both therapeutic and diagnostic sources in medical applications. To calculate radiation force an acoustic hologram can be used in conjunction with analytical expressions based on the angular spectrum of the measured field. The results of an experimental investigation of radiation forces in two different cases are presented in this paper. In one case, the radiation force of an obliquely incident ultrasound beam on a large absorber (which completely absorbs the beam) is considered. The second case concerns measurement of the radiation force on a spherical target that is small compared to the beam diameter.

  17. Synthesis of porous-acoustic absorbing systems by an evolutionary optimization method

    NASA Astrophysics Data System (ADS)

    Silva, F. I.; Pavanello, R.

    2010-10-01

    Topology optimization is frequently used to design structures and acoustic systems in a large range of engineering applications. In this work, a method is proposed for maximizing the absorbing performance of acoustic panels by using a coupled finite element model and evolutionary strategies. The goal is to find the best distribution of porous material for sound absorbing panels. The absorbing performance of the porous material samples in a Kundt tube is simulated using a coupled porous-acoustic finite element model. The equivalent fluid model is used to represent the foam material. The porous material model is coupled to a wave guide using a modal superposition technique. A sensitivity number indicating the optimum locations for porous material to be removed is derived and used in a numerical hard kill scheme. The sensitivity number is used to form an evolutionary porous material optimization algorithm which is verified through examples.

  18. Method of absorbing UF.sub.6 from gaseous mixtures in alkamine absorbents

    DOEpatents

    Lafferty, Robert H.; Smiley, Seymour H.; Radimer, Kenneth J.

    1976-04-06

    A method of recovering uranium hexafluoride from gaseous mixtures employing as an absorbent a liquid composition at least one of the components of which is chosen from the group consisting of ethanolamine, diethanolamine, and 3-methyl-3-amino-propane-diol-1,2.

  19. Determination of trace amount of formaldehyde base on a bromate-Malachite Green system

    NASA Astrophysics Data System (ADS)

    Tang, Yufang; Chen, Hao; Weng, Chao; Tang, Xiaohui; Zhang, Miaoling; Hu, Tao

    2015-01-01

    A novel catalytic kinetic spectrophotometric method for determination of trace amount of formaldehyde (FA) has been established, based on catalytic effect of trace amount of FA on the oxidation of Malachite Green (MG) by potassium bromate in presence of sulfuric acid medium, and was reported for the first time. The method was monitored by measuring the decrease in absorbance of MG at 617 nm and allowed a precise determination of FA in the range of 0.003-0.08 μg mL-1, with a limit of detection down to 1 ng mL-1. The relative standard deviation of 10 replicate measurements was 1.63%. The method developed was approved to be sensitive, selective and accurate, and adopted to determinate free FA in samples directly with good accuracy and reproducibility.

  20. Determination of trace amount of formaldehyde base on a bromate-Malachite Green system.

    PubMed

    Tang, Yufang; Chen, Hao; Weng, Chao; Tang, Xiaohui; Zhang, Miaoling; Hu, Tao

    2015-01-25

    A novel catalytic kinetic spectrophotometric method for determination of trace amount of formaldehyde (FA) has been established, based on catalytic effect of trace amount of FA on the oxidation of Malachite Green (MG) by potassium bromate in presence of sulfuric acid medium, and was reported for the first time. The method was monitored by measuring the decrease in absorbance of MG at 617 nm and allowed a precise determination of FA in the range of 0.003-0.08 μg mL(-1), with a limit of detection down to 1 ng mL(-1). The relative standard deviation of 10 replicate measurements was 1.63%. The method developed was approved to be sensitive, selective and accurate, and adopted to determinate free FA in samples directly with good accuracy and reproducibility.

  1. Stratocumulus to Cumulus Transition Capped by a Light-Absorbing Smoke Layer

    NASA Astrophysics Data System (ADS)

    Yamaguchi, T.; Feingold, G.; Kazil, J.; McComiskey, A. C.

    2015-12-01

    Biomass burning aerosol emitted from Africa seasonally advects over the eastern Atlantic and forms a layer of light-absorbing smoke above stratocumulus clouds, which influences heating profiles, dynamics, and cloud microphysics. In this study, large-eddy simulation is used to investigate the effect of the absorbing smoke layer on the stratocumulus to cumulus transition (SCT). A prognostic absorbing smoke model incorporates humidity effects on optical properties, and is coupled with a two-moment bulk microphysics scheme and an interactive radiation code. Smoke both absorbs shortwave radiation and acts as cloud condensation nuclei (CCN). Simulations are of three day duration. The simulations assess sensitivity of the SCT to distance of the smoke layer from the cloud top, aerosol optical thickness and single scattering albedo, and precipitation. Our simulations show that 1) As a shortwave absorber, the smoke stabilizes the free atmosphere and strengthens the temperature jump at the boundary layer top, which limits entrainment; 2) Smoke helps evaporate cloud during daytime, which amplifies the diurnal cycle of cloud cover; 3) As a source of CCN, the entrained smoke suppresses rain formation, which inhibits precipitation-generated cloud breakup. The net effect of smoke is modification of heating profiles to limit the deepening of the planetary boundary layer, and suppression of precipitation. This leads to enhancement of the diurnal cycle of cloudiness but a delay in the SCT.

  2. Infrared broadband metasurface absorber for reducing the thermal mass of a microbolometer.

    PubMed

    Jung, Joo-Yun; Song, Kyungjun; Choi, Jun-Hyuk; Lee, Jihye; Choi, Dae-Geun; Jeong, Jun-Ho; Neikirk, Dean P

    2017-03-27

    We demonstrate an infrared broadband metasurface absorber that is suitable for increasing the response speed of a microbolometer by reducing its thermal mass. A large fraction of holes are made in a periodic pattern on a thin lossy metal layer characterised with a non-dispersive effective surface impedance. This can be used as a non-resonant metasurface that can be integrated with a Salisbury screen absorber to construct an absorbing membrane for a microbolometer that can significantly reduce the thermal mass while maintaining high infrared broadband absorption in the long wavelength infrared (LWIR) band. The non-dispersive effective surface impedance can be matched to the free space by optimising the surface resistance of the thin lossy metal layer depending on the size of the patterned holes by using a dc approximation method. In experiments a high broadband absorption was maintained even when the fill factor of the absorbing area was reduced to 28% (hole area: 72%), and it was theoretically maintained even when the fill factor of the absorbing area was reduced to 19% (hole area: 81%). Therefore, a metasurface with a non-dispersive effective surface impedance is a promising solution for reducing the thermal mass of infrared microbolometer pixels.

  3. Nanometre optical coatings based on strong interference effects in highly absorbing media.

    PubMed

    Kats, Mikhail A; Blanchard, Romain; Genevet, Patrice; Capasso, Federico

    2013-01-01

    Optical coatings, which consist of one or more films of dielectric or metallic materials, are widely used in applications ranging from mirrors to eyeglasses and photography lenses. Many conventional dielectric coatings rely on Fabry-Perot-type interference, involving multiple optical passes through transparent layers with thicknesses of the order of the wavelength to achieve functionalities such as anti-reflection, high-reflection and dichroism. Highly absorbing dielectrics are typically not used because it is generally accepted that light propagation through such media destroys interference effects. We show that under appropriate conditions interference can instead persist in ultrathin, highly absorbing films of a few to tens of nanometres in thickness, and demonstrate a new type of optical coating comprising such a film on a metallic substrate, which selectively absorbs various frequency ranges of the incident light. These coatings have a low sensitivity to the angle of incidence and require minimal amounts of absorbing material that can be as thin as 5-20 nm for visible light. This technology has the potential for a variety of applications from ultrathin photodetectors and solar cells to optical filters, to labelling, and even the visual arts and jewellery.

  4. Field trials measuring the effects of ultraviolet-absorbing greenhouse plastic films on insect populations.

    PubMed

    Costa, H S; Robb, K L; Wilen, C A

    2002-02-01

    Field studies were conducted to compare insect population levels in greenhouse crops covered with plastics that block the transmission of UV light in two wavelength ranges. Crops grown in greenhouses under a plastic that blocked UV light at wavelengths of 380 nm and below had lower numbers of aphids and thrips compared with a plastic that blocked UV light at wavelengths of 360 nm and below. This is consistent with the results found for thrips in previous studies using small, completely enclosed tunnels with no plant material. The effects were not as dramatic in the commercial greenhouses, perhaps due to unfiltered light entering through the open sides of those greenhouses. There was no reduction in greenhouse whitefly, Trialeurodes vaporariorum Westwood, populations under the <380 UV-absorbing plastic compared to <360 nm UV-absorbing plastic in these field trials. This is inconsistent with results found in small, completely enclosed tunnels, where sticky traps caught a significantly higher proportion (95 +/- 2%) of released greenhouse whiteflies inside tunnels covered with <360 nm absorbing plastic compared with the <380 nm absorbing plastic. The results of these studies suggest that the type of greenhouse plastic used in a structure can affect population levels of some insect species, and may be useful tools in developing integrated pest management programs for insect management. The design of the greenhouse and amount of unfiltered light that enters the system appear to be important factors in determining the level of effect.

  5. Cross-Linking Amine-Rich Compounds into High Performing Selective CO2 Absorbents

    NASA Astrophysics Data System (ADS)

    Andreoli, Enrico; Dillon, Eoghan P.; Cullum, Laurie; Alemany, Lawrence B.; Barron, Andrew R.

    2014-12-01

    Amine-based absorbents play a central role in CO2 sequestration and utilization. Amines react selectively with CO2, but a drawback is the unproductive weight of solvent or support in the absorbent. Efforts have focused on metal organic frameworks (MOFs) reaching extremely high CO2 capacity, but limited selectivity to N2 and CH4, and decreased uptake at higher temperatures. A desirable system would have selectivity (cf. amine) and high capacity (cf. MOF), but also increased adsorption at higher temperatures. Here, we demonstrate a proof-of-concept where polyethyleneimine (PEI) is converted to a high capacity and highly selective CO2 absorbent using buckminsterfullerene (C60) as a cross-linker. PEI-C60 (CO2 absorption of 0.14 g/g at 0.1 bar/90°C) is compared to one of the best MOFs, Mg-MOF-74 (0.06 g/g at 0.1 bar/90°C), and does not absorb any measurable amount of CH4 at 50 bar. Thus, PEI-C60 can perform better than MOFs in the sweetening of natural gas.

  6. Performance of four carbon dioxide absorbents in experimental and clinical settings.

    PubMed

    Yamakage, M; Takahashi, K; Takahashi, M; Satoh, J-I; Namiki, A

    2009-03-01

    To evaluate the performance of four kinds of carbon dioxide (CO(2)) absorbents (Medisorb GE Healthcare, Amsorb Plus Armstrong Medical, YabashiLime Yabashi Industries, and Sodasorb LF Grace Performance Chemicals), we measured their dust production, acceptability of colour indicator, and CO(2) absorption capacity in in vitro experimental settings and the concentration of compound A in an inspired anaesthetic circuit during in vivo clinical practice. In vitro, the order of the dust amount was Sodasorb LF > Medisorb > Amsorb Plus = YabashiLime both before and after shaking. The order of the color acceptability was similar: Sodasorb LF > Amsorb Plus = Medisorb > YabashiLime both initially and 16 h after CO(2) exhaustion. During exposure to 200 ml.min(-1) CO(2) in vitro, the period until 1 kg of fresh soda lime allowed inspired CO(2) to increase to 0.7 kPa (as a mark of utilisation of the absorbent) was longer with Medisorb (1978 min) than with the other absorbents (1270-1375 min). In vivo, compound A (1.0% inspired sevoflurane) was detected only when using Medisorb. While Medisorb has the best ability to absorb CO(2), it alone produces compound A.

  7. Nanometre optical coatings based on strong interference effects in highly absorbing media

    NASA Astrophysics Data System (ADS)

    Kats, Mikhail A.; Blanchard, Romain; Genevet, Patrice; Capasso, Federico

    2013-01-01

    Optical coatings, which consist of one or more films of dielectric or metallic materials, are widely used in applications ranging from mirrors to eyeglasses and photography lenses. Many conventional dielectric coatings rely on Fabry-Perot-type interference, involving multiple optical passes through transparent layers with thicknesses of the order of the wavelength to achieve functionalities such as anti-reflection, high-reflection and dichroism. Highly absorbing dielectrics are typically not used because it is generally accepted that light propagation through such media destroys interference effects. We show that under appropriate conditions interference can instead persist in ultrathin, highly absorbing films of a few to tens of nanometres in thickness, and demonstrate a new type of optical coating comprising such a film on a metallic substrate, which selectively absorbs various frequency ranges of the incident light. These coatings have a low sensitivity to the angle of incidence and require minimal amounts of absorbing material that can be as thin as 5-20 nm for visible light. This technology has the potential for a variety of applications from ultrathin photodetectors and solar cells to optical filters, to labelling, and even the visual arts and jewellery.

  8. Cross-Linking Amine-Rich Compounds into High Performing Selective CO2 Absorbents

    PubMed Central

    Andreoli, Enrico; Dillon, Eoghan P.; Cullum, Laurie; Alemany, Lawrence B.; Barron, Andrew R.

    2014-01-01

    Amine-based absorbents play a central role in CO2 sequestration and utilization. Amines react selectively with CO2, but a drawback is the unproductive weight of solvent or support in the absorbent. Efforts have focused on metal organic frameworks (MOFs) reaching extremely high CO2 capacity, but limited selectivity to N2 and CH4, and decreased uptake at higher temperatures. A desirable system would have selectivity (cf. amine) and high capacity (cf. MOF), but also increased adsorption at higher temperatures. Here, we demonstrate a proof-of-concept where polyethyleneimine (PEI) is converted to a high capacity and highly selective CO2 absorbent using buckminsterfullerene (C60) as a cross-linker. PEI-C60 (CO2 absorption of 0.14 g/g at 0.1 bar/90°C) is compared to one of the best MOFs, Mg-MOF-74 (0.06 g/g at 0.1 bar/90°C), and does not absorb any measurable amount of CH4 at 50 bar. Thus, PEI-C60 can perform better than MOFs in the sweetening of natural gas. PMID:25467054

  9. Just the Right Amount of Reinforcement

    NASA Technical Reports Server (NTRS)

    Walton, Greg

    1998-01-01

    Lockheed Martin Skunk Works, is taking the next step towards economical low-Earth-orbit (LEO) operations with NASA's X-33 technology demonstrator, that uses composite tanks for liquid hydrogen (LH sub2) fuel storage and structural support, The X-33 is a 53% scale model of the VentureStar single-stage-to-orbit (SSTO) reusable launch vehicle(RLV) projected to orbit payloads at a rate, of $1,000 per pound beginning in 2004 In order to make VentureStar completely reusable and economical engineers are using composite materials throughout the spacecrafts structure. The first test of the design comes in 1999 on the X-33 technology demonstrator. Two of the primary structures that engineers will be evaluating are the carbon fiber/epoxy LH2 fuel tanks. The 29-ft long by 18-ft wide tanks, which fill two-thirds of the X-33's interior, serve a dual purpose carrying fuel and providing structural support to the walls of the spacecraft. Fiber placement makes it possible to build the fuel tanks, large, light and strong enough to satisfy X33's requirements. Lockheed Martin choose the fabrication technology to produce the eight sections of each tank because of fiber placement's ability to handle complex surfaces, speed and repeatability.

  10. Querying Large Biological Network Datasets

    ERIC Educational Resources Information Center

    Gulsoy, Gunhan

    2013-01-01

    New experimental methods has resulted in increasing amount of genetic interaction data to be generated every day. Biological networks are used to store genetic interaction data gathered. Increasing amount of data available requires fast large scale analysis methods. Therefore, we address the problem of querying large biological network datasets.…

  11. Construction of Nontoxic Polymeric UV-Absorber with Great Resistance to UV-Photoaging

    NASA Astrophysics Data System (ADS)

    Huang, Zhong; Ding, Aishun; Guo, Hao; Lu, Guolin; Huang, Xiaoyu

    2016-05-01

    In this article, we developed a series of new nontoxic polymeric UV-absorbers through covalently attaching a benzophenone derivative onto the main chain of poly(vinyl chloride) (PVC) via mild and quantitative click chemistry. Azide groups were firstly introduced into the backbone of PVC via a nucleophilic reaction without affecting polymeric skeleton. Copper-catalyzed Husigen-Click cycloaddition reaction was performed between the pendant azide groups of PVC and alkynyl of (2-hydroxy-4-(prop-2-ynyloxy)phenyl)(phenyl)methanone at ambient temperature for affording the desired PVC-based UV-absorbers (PVC-UV) with different amounts of benzophenone moieties, which displayed great resistance to photoaging without degradation while exposed to UV irradiation. These polymeric UV-absorbers also showed good solubilities in common organic solvents and no cytotoxicity vs. HaCat cell. Small amounts of PVC-UV were homogeneously mixed with PVC as additive for stabilizing PVC against UV-photoaging without degradation and releasing small molecule even after 200 h while keeping thermal stability. This route of polymeric additive clearly paved an efficient way for solving the puzzle of separation of small molecule additive.

  12. Construction of Nontoxic Polymeric UV-Absorber with Great Resistance to UV-Photoaging

    PubMed Central

    Huang, Zhong; Ding, Aishun; Guo, Hao; Lu, Guolin; Huang, Xiaoyu

    2016-01-01

    In this article, we developed a series of new nontoxic polymeric UV-absorbers through covalently attaching a benzophenone derivative onto the main chain of poly(vinyl chloride) (PVC) via mild and quantitative click chemistry. Azide groups were firstly introduced into the backbone of PVC via a nucleophilic reaction without affecting polymeric skeleton. Copper-catalyzed Husigen-Click cycloaddition reaction was performed between the pendant azide groups of PVC and alkynyl of (2-hydroxy-4-(prop-2-ynyloxy)phenyl)(phenyl)methanone at ambient temperature for affording the desired PVC-based UV-absorbers (PVC-UV) with different amounts of benzophenone moieties, which displayed great resistance to photoaging without degradation while exposed to UV irradiation. These polymeric UV-absorbers also showed good solubilities in common organic solvents and no cytotoxicity vs. HaCat cell. Small amounts of PVC-UV were homogeneously mixed with PVC as additive for stabilizing PVC against UV-photoaging without degradation and releasing small molecule even after 200 h while keeping thermal stability. This route of polymeric additive clearly paved an efficient way for solving the puzzle of separation of small molecule additive. PMID:27138547

  13. White-Light-Induced Collective Heating of Gold Nanocomposite/Bombyx mori Silk Thin Films with Ultrahigh Broadband Absorbance.

    PubMed

    Tsao, Shao Hsuan; Wan, Dehui; Lai, Yu-Sheng; Chang, Ho-Ming; Yu, Chen-Chieh; Lin, Keng-Te; Chen, Hsuen-Li

    2015-12-22

    This paper describes a systematic investigation of the phenomenon of white-light-induced heating in silk fibroin films embedded with gold nanoparticles (Au NPs). The Au NPs functioned to develop an ultrahigh broadband absorber, allowing white light to be used as a source for photothermal generation. With an increase of the Au content in the composite films, the absorbance was enhanced significantly around the localized surface plasmon resonance (LSPR) wavelength, while non-LSPR wavelengths were also increased dramatically. The greater amount of absorbed light increased the rate of photoheating. The optimized composite film exhibited ultrahigh absorbances of approximately 95% over the spectral range from 350 to 750 nm, with moderate absorbances (>60%) at longer wavelengths (750-1000 nm). As a result, the composite film absorbed almost all of the incident light and, accordingly, converted this optical energy to local heat. Therefore, significant temperature increases (ca. 100 °C) were readily obtained when we irradiated the composite film under a light-emitting diode or halogen lamp. Moreover, such composite films displayed linear light-to-heat responses with respect to the light intensity, as well as great photothermal stability. A broadband absorptive film coated on a simple Al/Si Schottky diode displayed a linear, significant, stable photo-thermo-electronic effect in response to varying the light intensity.

  14. Ultrathin microwave absorber based on metamaterial

    NASA Astrophysics Data System (ADS)

    Kim, Y. J.; Yoo, Y. J.; Hwang, J. S.; Lee, Y. P.

    2016-11-01

    We suggest that ultrathin broadband metamaterial is a perfect absorber in the microwave regime by utilizing the properties of a resistive sheet and metamaterial. Meta-atoms are composed of four-leaf clover-shape metallic patterns and a metal plane separated by three intermediate resistive sheet layers between four dielectric layers. We interpret the absorption mechanism of the broadband by using the distribution of surface currents at specific frequencies. The simulated absorption was over 99% in 1.8-4.2 GHz. The corresponding experimental absorption was also over 99% in 2.62-4.2 GHz; however, the absorption was slightly lower than 99% in 1.8-2.62 GHz because of the sheet resistance and the changed values for the dielectric constant. Furthermore, it is independent of incident angle. The results of this research indicate the possibility of applications, due to the suppression of noxious exposure, in cell phones, computers and microwave equipments.

  15. Electromagnetic radiation absorbers and modulators comprising polyaniline

    DOEpatents

    Epstein, Arthur J.; Ginder, John M.; Roe, Mitchell G.; Hajiseyedjavadi, Hamid

    1992-01-01

    A composition for absorbing electromagnetic radiation, wherein said electromagnetic radiation possesses a wavelength generally in the range of from about 1000 Angstroms to about 50 meters, wherein said composition comprises a polyaniline composition of the formula ##STR1## where y can be equal to or greater than zero, and R.sup.1 and R.sup.2 are independently selected from the group containing of H, --OCH.sub.3, --CH.sub.3, --F, --Cl, --Br, --I, NR.sup.3 .sub.2, --NHCOR.sup.3, --OH, --O.sup.-, SR.sup.3, --OCOR.sup.3, --NO.sub.2, --COOH, --COOR.sup.3, --COR.sup.3, --CHO, and --CN, where R.sup.3 is a C.sub.1 to C.sub.8 alkyl, aryl or aralkyl group.

  16. Cusps, self-organization, and absorbing states.

    PubMed

    Bonachela, Juan A; Alava, Mikko; Muñoz, Miguel A

    2009-05-01

    Elastic interfaces embedded in (quenched) random media exhibit metastability and stick-slip dynamics. These nontrivial dynamical features have been shown to be associated with cusp singularities of the coarse-grained disorder correlator. Here we show that annealed systems with many absorbing states and a conservation law but no quenched disorder exhibit identical cusps. On the other hand, similar nonconserved systems in the directed percolation class are also shown to exhibit cusps but of a different type. These results are obtained both by a recent method to explicitly measure disorder correlators and by defining an alternative new protocol inspired by self-organized criticality, which opens the door to easily accessible experimental realizations.

  17. Electronic and thermally tunable infrared metamaterial absorbers

    NASA Astrophysics Data System (ADS)

    Shrekenhamer, David; Miragliotta, Joseph A.; Brinkley, Matthew; Fan, Kebin; Peng, Fenglin; Montoya, John A.; Gauza, Sebastian; Wu, Shin-Tson; Padilla, Willie J.

    2016-09-01

    In this paper, we report a computational and experimental study using tunable infrared (IR) metamaterial absorbers (MMAs) to demonstrate frequency tunable (7%) and amplitude modulation (61%) designs. The dynamic tuning of each structure was achieved through the addition of an active material—liquid crystals (LC) or vanadium dioxide (VO2)-within the unit cell of the MMA architecture. In both systems, an applied stimulus (electric field or temperature) induced a dielectric change in the active material and subsequent variation in the absorption and reflection properties of the MMA in the mid- to long-wavelength region of the IR (MWIR and LWIR, respectively). These changes were observed to be reversible for both systems and dynamic in the LC-based structure.

  18. Porous Carbon Nanoparticle Networks with Tunable Absorbability

    PubMed Central

    Dai, Wei; Kim, Seong Jin; Seong, Won-Kyeong; Kim, Sang Hoon; Lee, Kwang-Ryeol; Kim, Ho-Young; Moon, Myoung-Woon

    2013-01-01

    Porous carbon materials with high specific surface areas and superhydrophobicity have attracted much research interest due to their potential application in the areas of water filtration, water/oil separation, and oil-spill cleanup. Most reported superhydrophobic porous carbon materials are fabricated by complex processes involving the use of catalysts and high temperatures but with low throughput. Here, we present a facile single-step method for fabricating porous carbon nanoparticle (CNP) networks with selective absorbability for water and oils via the glow discharge of hydrocarbon plasma without a catalyst at room temperature. Porous CNP networks were grown by the continuous deposition of CNPs at a relatively high deposition pressure. By varying the fluorine content, the porous CNP networks exhibited tunable repellence against liquids with various degrees of surface tension. These porous CNP networks could be applied for the separation of not only water/oil mixtures but also mixtures of liquids with different surface tension levels. PMID:23982181

  19. Absorbing layers for the Dirac equation

    SciTech Connect

    Pinaud, Olivier

    2015-05-15

    This work is devoted to the construction of perfectly matched layers (PML) for the Dirac equation, that not only arises in relativistic quantum mechanics but also in the dynamics of electrons in graphene or in topological insulators. While the resulting equations are stable at the continuous level, some care is necessary in order to obtain a stable scheme at the discrete level. This is related to the so-called fermion doubling problem. For this matter, we consider the numerical scheme introduced by Hammer et al. [19], and combine it with the discretized PML equations. We state some arguments for the stability of the resulting scheme, and perform simulations in two dimensions. The perfectly matched layers are shown to exhibit, in various configurations, superior absorption than the absorbing potential method and the so-called transport-like boundary conditions.

  20. Absorbed doses from temporomandibular joint radiography

    SciTech Connect

    Brooks, S.L.; Lanzetta, M.L.

    1985-06-01

    Thermoluminescent dosimeters were used in a tissue-equivalent phantom to measure doses of radiation absorbed by various structures in the head when the temporomandibular joint was examined by four different radiographic techniques--the transcranial, transorbital, and sigmoid notch (Parma) projections and the lateral tomograph. The highest doses of radiation occurred at the point of entry for the x-ray beam, ranging from 112 mrad for the transorbital view to 990 mrad for the sigmoid notch view. Only the transorbital projection a radiation dose to the lens of the eye. Of the four techniques evaluated, the lateral tomograph produced the highest doses to the pituitary gland and the bone marrow, while the sigmoid notch radiograph produced the highest doses to the parotid gland.