Science.gov

Sample records for ac coupling loss

  1. AC Loss Analysis on the Superconducting Coupling Magnet in MICE

    SciTech Connect

    Wu, Hong; Wang, Li; Green, Michael; Li, LanKai; Xu, FengYu; Liu, XiaoKun; Jia, LinXinag

    2008-07-08

    A pair of coupling solenoids is used in MICE experiment to generate magnetic field which keeps the muons within the iris of thin RF cavity windows. The coupling solenoids have a 1.5-meter inner diameter and will produce 7.4 T peak magnetic field. Three types of AC losses in coupling solenoid are discussed. The affect of AC losses on the temperature distribution within the cold mass during charging and rapid discharging process is analyzed also. The analysis result will be further confirmed by the experiment of the prototype solenoid for coupling solenoid, which will be designed, fabricated and tested at ICST.

  2. Second VAMAS a.c. loss measurement intercomparison: a.c. magnetization measurement of hysteresis and coupling losses in NbTi multifilamentary strands

    NASA Astrophysics Data System (ADS)

    Schmidt, C.; Itoh, K.; Wada, H.

    The article summarizes results of part of the second VAMAS a.c. loss measurement intercomparison. This program was carried out at 17 participating laboratories on two sets of multifilamentary NbTi strands (Set No. 1: copper matrix, fil. diam. between 0.5 and 12 μm; Set No. 2: cupronickel matrix, fil. diam. between 0.4 and 1.2 μm). The results reported here were measured by means of a.c. magnetization methods and separated into hysteresis and coupling losses. One laboratory used a calorimetric method. The data scatter in measured hysteresis losses among the participating laboratories was reasonably small for different measuring methods adopted and experimental arrangements used. On the other hand, the data scatter in coupling losses was large, mainly because in most laboratories a.c. losses were measured only at low frequencies (below 1 Hz), where the separation of coupling losses from total losses tends to be inaccurate. The comparison of measured hysteresis losses with the critical state model showed a large disagreement, which is assumed to be due to proximity effect coupling between filaments. 1997 Elsevier Science Limited

  3. AC loss in superconducting tapes and cables

    NASA Astrophysics Data System (ADS)

    Oomen, Marijn Pieter

    High-temperature superconductors are developed for use in power-transmission cables, transformers and motors. The alternating magnetic field in these devices causes AC loss, which is a critical factor in the design. The study focuses on multi-filament Bi-2223/Ag tapes exposed to a 50-Hz magnetic field at 77 K. The AC loss is measured with magnetic, electric and calorimetric methods. The results are compared to theoretical predictions based mainly on the Critical-State Model. The loss in high- temperature superconductors is affected by their characteristic properties: increased flux creep, high aspect ratio and inhomogeneties. Filament intergrowths and a low matrix resistivity cause a high coupling-current loss especially when the filaments are fully coupled. When the wide side of the tape is parallel to the external magnetic field, the filaments are decoupled by twisting. In a perpendicular field the filaments can be decoupled only by combining a short twist pitch with a transverse resistivity much higher than that of silver. The arrangement of the inner filaments determines the transverse resistivity. Ceramic barriers around the filaments cause partial decoupling in perpendicular magnetic fields at power frequencies. The resultant decrease in AC loss is greater than the accompanying decrease in critical current. With direct transport current in alternating magnetic field, the transport-current loss is well described with a new model for the dynamic resistance. The Critical- State Model describes well the magnetisation and total AC loss in parallel magnetic fields, at transport currents up to 0.7 times the critical current. When tapes are stacked face-to-face in a winding, the AC-loss density in perpendicular fields is greatly decreased due to the mutual shielding of the tapes. Coupling currents between the tapes in a cable cause an extra AC loss, which is reduced by a careful cable design. The total AC loss in complex devices with many tapes is generally well

  4. Ac loss calorimeter for three-phase cable

    SciTech Connect

    Daney, D.E.; Boenig, H.J.; Maley, M.P.; McMurry, D.E.; DeBlanc, B.G.

    1996-10-01

    A calorimeter for measuring ac losses in meter-long lengths of HTS superconducting power transmission line cables is described. The calorimeter, which is based on a temperature difference technique, has a precision of 1 mW and measures single, two-phase (coupling), and three-phase losses. The measurements show significant coupling losses between phases.

  5. Superconductor coil geometry and ac losses

    NASA Technical Reports Server (NTRS)

    Pierce, T. V., Jr.; Zapata, R. N.

    1976-01-01

    An empirical relation is presented which allows simple computation of volume-averaged winding fields from central fields for coils of small rectangular cross sections. This relation suggests that, in certain applications, ac-loss minimization can be accomplished by use of low winding densities, provided that hysteresis losses are independent of winding density. The ac-loss measurements on coils wound of twisted multifilamentary composite superconductors show no significant dependence on ac losses on winding density, thus permitting the use of winding density as an independent design parameter in loss minimization.

  6. AC Losses in the MICE Channel Magnets -- Is This a Curse or aBlessing?

    SciTech Connect

    Green, M.A.; Wu, H.; Wang, L.; Kai, L.L.; Jia, L.X.; Yang, S.Q.

    2008-01-31

    This report discusses the AC losses in the MICE channelmagnets during magnet charging and discharging. This report talks aboutthe three types of AC losses in the MICE magnets; the hysteretic AC lossin the superconductor, the coupling AC loss in the superconductor and theeddy current AC loss in the magnet mandrel and support structure. AClosses increase the heat load at 4 K. The added heat load increases thetemperature of the second stage of the cooler. In addition, AC losscontributes to the temperature rise between the second stage cold headand the high field point of the magnet, which is usually close to themagnet hot spot. These are the curses of AC loss in the MICE magnet thatcan limit the rate at which the magnet can be charge or discharged. Ifone is willing to allow some of the helium that is around the magnet toboil away during a magnet charge or discharge, AC losses can become ablessing. The boil off helium from the AC losses can be used to cool theupper end of the HTS leads and the surrounding shield. The AC losses arepresented for all three types of MICE magnets. The AC loss temperaturedrops within the coupling magnet are presented as an example of how boththe curse and blessing of the AC losses can be combined.

  7. Roebel assembled coated conductor cables (RACC): Ac-Losses and current carrying potential

    NASA Astrophysics Data System (ADS)

    Frank, A.; Heller, R.; Goldacker, W.; Kling, A.; Schmidt, C.

    2008-02-01

    Low ac-loss HTS cables for transport currents well above 1 kA are required for application in transformers and generators and are taken into consideration for future generations of fusion reactor coils. Coated conductors (CC) are suitable candidates for high field application at an operation temperature in the range 50-77 K. Ac-field applications require cables with low ac-losses and hence twisting of the individual strands. We solved this problem using the Roebel technique. Short lengths of Roebel bar cables were prepared from industrial DyBCO and YBCO-CC. Meander shaped tapes of 4 or 5 mm width with twist pitches of 123 or 127 mm were cut from the 10 or 12 mm wide CC tapes using a specially designed tool. Eleven or twelve of these strands were assembled to a cable. The electrical and mechanical connection of the tapes was achieved using a silver powder filled conductive epoxy resin. Ac-losses of a short sample in an external ac-field were measured as a function of frequency and field amplitude as well as the coupling current decay time constant. We discuss the results in terms of available theories and compare measured time constants in transverse field with measured coupling losses. Finally the potential of this cable type for ac-use is discussed with respect to ac-losses and current carrying capability.

  8. AC Loss Measurements on a 2G YBCO Coil

    SciTech Connect

    Rey, Christopher M; Duckworth, Robert C; Schwenterly, S W

    2011-01-01

    The Oak Ridge National Laboratory (ORNL) is collaborating with Waukesha Electric Systems (WES) to continue development of HTS power transformers. For compatibility with the existing power grid, a commercially viable HTS transformer will have to operate at high voltages in the range of 138 kV and above, and will have to withstand 550-kV impulse voltages as well. Second-generation (2G) YBCO coated conductors will be required for an economically-competitive design. In order to adequately size the refrigeration system for these transformers, the ac loss of these HTS coils must be characterized. Electrical AC loss measurements were conducted on a prototype high voltage (HV) coil with co-wound stainless steel at 60 Hz in a liquid nitrogen bath using a lock-in amplifier technique. The prototype HV coil consisted of 26 continuous (without splice) single pancake coils concentrically centered on a stainless steel former. For ac loss measurement purposes, voltage tap pairs were soldered across each set of two single pancake coils so that a total of 13 separate voltage measurements could be made across the entire length of the coil. AC loss measurements were taken as a function of ac excitation current. Results show that the loss is primarily concentrated at the ends of the coil where the operating fraction of critical current is the highest and show a distinct difference in current scaling of the losses between low current and high current regimes.

  9. Effect of Interfacial Resistance on AC Loss as a Function of Applied AC Field in YBCO Filamentary Conductors

    SciTech Connect

    Duckworth, Robert C; List III, Frederick Alyious; Zhang, Yifei

    2009-01-01

    To reduce ac loss in Y-Ba-Cu-O (YBCO) coated conductors while maintaining current sharing between filaments, an attempt was made to introduce an interfacial resistance between the YBCO filaments and a continuous silver cap layer. The YBCO filaments were produced via laser scribing of MOCVD YBCO films deposited on standard Ion Beam Assisted Deposition (IBAD) templates. After laser scribing, the filaments were exposed to air at room temperature to degrade the YBCO surface. A three micron thick silver cap layer was then and each sample was oxygen annealed at different temperature to produce different interface resistance at the interface between the silver and YBCO. Measurements of the ac loss was measured as a function of applied perpendicular field and frequency revealed a correlation between the reduction in coupling loss and the oxygen annealing temperature.

  10. Magnetization AC losses in MgB2 wires made by IMD process

    NASA Astrophysics Data System (ADS)

    Kováč, J.; Šouc, J.; Kováč, P.; Hušek, I.

    2015-01-01

    Magnetization AC losses of MgB2 superconductors with one and four filaments made by an internal magnesium diffusion (IMD) into boron process were measured and analyzed. For AC loss measurement a system based on a calibration-free method was used. Short samples of MgB2 wires were exposed to an external magnetic field with amplitudes up to 0.07 T, frequencies up to 1200 Hz, and a temperature range between 15 K and 40 K. A strong effect of eddy current losses was found in single-core wire containing pure copper sheath, which was proved by the same wire measurement after Cu etching. The impact of coupling current losses in non-twisted four-filament wire and the decoupling effect after twisting were observed. Coupling current losses in a low-frequency region were effectively reduced in agreement with theoretical assumption. The degradation of transport currents due to torsion stress by twisting was taken into account and the normalized AC losses of MgB2 wires made by IMD and powder-in-tube processes were compared. It appears that the IMD process is more perspective for AC applications due to much higher current densities and smaller degradation of current-carrying capability by twisting.

  11. Measurement of coupling resonance driving terms with the AC dipole

    SciTech Connect

    Miyamoto, R.

    2010-10-01

    Resonance driving terms for linear coupled betatron motion in a synchrotron ring can be determined from corresponding spectral lines of an excited coherent beam motion. An AC dipole is one of instruments to excite such a motion. When a coherent motion is excited with an AC dipole, measured Courant-Snyder parameters and betatron phase advance have apparent modulations, as if there is an additional quadrupole field at the location of the AC dipole. Hence, measurements of these parameters using the AC dipole require a proper interpretation of observed quantities. The situation is similar in measurements of resonance driving terms using the AC dipole. In this note, we derive an expression of coupled betatron motion excited with two AC dipoles in presence of skew quadrupole fields, discuss an impact of this quadrupole like effect of the AC dipole on a measurement of coupling resonance driving terms, and present an analytical method to determine the coupling resonance driving terms from quantities observed using the AC dipole.

  12. AC current distribution and losses in multifilamentary superconductors exposed to longitudinal magnetic field

    SciTech Connect

    Le Naour, S.; Lacaze, A.; Laumond, Y.; Estop, P.; Verhaege, T.

    1996-07-01

    The current distribution and also AC losses, in a multifilamentary superconductor carrying a transport current, are influenced by the self and the external magnetic field. By using the Maxwell equations, a model has been developed in order to calculate the temporal evolution of current distribution in a single wire exposed or not to external magnetic field. This model is based on the actual relationship of electrical field E with current density J and takes into account the twist pitch of the wire. AC losses are calculated by adding all local losses through the cross section. This paper presents calculations of the influence of the cable twist coupled with the longitudinal magnetic field, and also gives some ideas how to decrease losses.

  13. Superconducting shielded core reactor with reduced AC losses

    DOEpatents

    Cha, Yung S.; Hull, John R.

    2006-04-04

    A superconducting shielded core reactor (SSCR) operates as a passive device for limiting excessive AC current in a circuit operating at a high power level under a fault condition such as shorting. The SSCR includes a ferromagnetic core which may be either closed or open (with an air gap) and extends into and through a superconducting tube or superconducting rings arranged in a stacked array. First and second series connected copper coils each disposed about a portion of the iron core are connected to the circuit to be protected and are respectively wound inside and outside of the superconducting tube or rings. A large impedance is inserted into the circuit by the core when the shielding capability of the superconducting arrangement is exceeded by the applied magnetic field generated by the two coils under a fault condition to limit the AC current in the circuit. The proposed SSCR also affords reduced AC loss compared to conventional SSCRs under continuous normal operation.

  14. Measurements of AC Losses and Current Distribution in Superconducting Cables

    SciTech Connect

    Nguyen, Doan A; Ashworth, Stephen P; Duckworth, Robert C; Carter, Bill; Fleshler, Steven

    2011-01-01

    This paper presents our new experimental facility and techniques to measure ac loss and current distribution between the layers for High Temperature Superconducting (HTS) cables. The facility is powered with a 45 kVA three-phase power supply which can provide three-phase currents up to 5 kA per phase via high current transformers. The system is suitable for measurements at any frequency between 20 and 500 Hz to better understand the ac loss mechanisms in HTS cables. In this paper, we will report techniques and results for ac loss measurements carried out on several HTS cables with and without an HTS shielding layer. For cables without a shielding layer, care must be taken to control the effect of the magnetic fields from return currents on loss measurements. The waveform of the axial magnetic field was also measured by a small pick-up coil placed inside a two-layer cable. The temporal current distribution between the layers can be calculated from the waveform of the axial field.

  15. AC magnetic field losses in BSCCO-2223 superconducting tapes

    SciTech Connect

    Lelovic, M.; Mench, S.; Deis, T.

    1997-09-01

    The AC magnetic losses at power frequencies (60 Hz) were investigated for mono- and multifilament Ag-sheathed (Bi, Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub y} (BSCCO-2223) tapes with similar transport critical current (I{sub c}) values at 77 K. The multifilament sample exhibited higher losses than the monofilament under the same conditions. Loss peaks are discussed in terms of intergranular, intragranular and eddy current losses. Because of BSCCO`s anisotropy, field orientation has a large effect on the magnitude of these peaks, even at relatively small angles. Losses for fields applied parallel to the c-axis of the textured BSCCO grains are larger by more than one order of magnitude than those applied perpendicular.

  16. Low-loss coupling to dielectric resonators

    NASA Technical Reports Server (NTRS)

    Hearn, C. P.; Bradshaw, E. S.; Trew, R. J.; Hefner, B. B., Jr.

    1991-01-01

    A compilation is presented of experimental observations and arguments concerning the use of dielectric resonators in applications requiring both tight coupling (beta greater than 10) and high unloaded Q, such as low loss bandpass filters. The microstrip coupled dielectric resonator is the primary focus, but an alternative coupling technique is discussed and comparatively evaluated. It is concluded that coupling factors as large as 65 are achievable.

  17. Hysteresis of sextupole and ac loss in Energy Doubler dipole magnets

    SciTech Connect

    Ishibashi, K.

    1982-06-18

    A simple model gave utilized for calculation of magnetization effects on ac loss and sextupole for Energy Doubler dipole magnets. The calculation in the simple model gave an underestimation of ac loss by about 30%. Results of computation on ac harmonics were also described.

  18. Oxidative coupling of methane with ac and dc corona discharges

    SciTech Connect

    Liu, C.; Marafee, A.; Hill, B.; Xu, G.; Mallinson, R.; Lobban, L.

    1996-10-01

    The oxidative coupling of methane (OCM) is being actively studied for the production of higher hydrocarbons from natural gas. The present study concentrated on the oxidative conversion of methane in an atmospheric pressure, nonthermal plasma formed by ac or dc corona discharges. Methyl radicals are formed by reaction with negatively-charged oxygen species created in the corona discharge. The selectivity to products ethane and ethylene is affected by electrode polarity, frequency, and oxygen partial pressure in the feed. Higher C{sub 2} yields were obtained with the ac corona. All the ac corona discharges are initiated at room temperature (i.e., no oven or other heat source is used), and the temperature increases to 300--500 C due to the exothermic reactions and the discharge itself. The largest C{sub 2} yield is 21% with 43.3% methane conversion and 48.3% C{sub 2} selectivity at a flowrate of 100 cm{sup 3}/min when the ac corona is at 30 Hz, 5 kV (rms) input power was used. The methane conversion may be improved to more than 50% by increasing the residence time, but the C{sub 2} selectivity decreases. A reaction mechanism including the oxidative dehydrogenation (OXD) of ethane to ethylene is presented to explain the observed phenomena. The results suggest that ac and/or dc gas discharge techniques have significant promise for improving the economics of OCM processes.

  19. Dependence of the ac loss on the aspect ratio in a cable in conduit conductor

    NASA Astrophysics Data System (ADS)

    Cau, F.; Bruzzone, P.

    2010-04-01

    The coupling current loss in rectangular superconducting cables is strictly dependent on their aspect ratio, which has an impact on the area linked by the field variation and consequently on the currents induced between strands. The relation between the ac loss and aspect ratio is studied with reference to the testing of three short cable in conduit conductor (CICC) samples at the SULTAN test facility. The first conductor is a 25 kA NbTi cable for the JT60-SA tokamak; the second is a 20 kA Nb3Sn cable for the HZB hybrid magnet. The last CICC is a 68 kA Nb3Sn cable with layout similar to that of the ITER toroidal field (TF) conductor (called the 'European toroidal field (EUTF) alternate'). All the samples are assembled with two conductor sections differing only in their orientation with respect to the external variable field. In the first and third samples, the cable of one leg is rotated by 90°, while in the HZB sample it is rotated by 45° with respect to the other leg. The ac loss is measured at the SULTAN test facility using a gas flow calorimetric method. A sample length of 39 cm is exposed to a sinusoidal field with an amplitude of ± 0.3 or ± 0.2 T (depending on the superconductor) and frequency variable in the range 0.1-0.8 Hz. A background field of 2 T perpendicular both to the sinusoidal field and to the sample axis is also applied. The ac loss is assessed by measuring the variation of the He enthalpy, assuming the metal enthalpy to be negligible. The loss curve for both legs is discussed in terms of the respective aspect ratios and the results, including data from former test campaigns, are compared with the aim of finding an analytical relation between the loss and the conductor dimensions.

  20. Development of Low AC Loss TFA-MOD Coated Conductors

    NASA Astrophysics Data System (ADS)

    Katayama, K.; Machi, T.; Nakamura, T.; Takagi, Y.; Nakaoka, K.; Yoshizumi, M.; Izumi, T.; Shiohara, Y.

    TFA-MOD process is expected to be promising for future applications since it can produce high performance YBCO coated conductors (CCs) with low cost. Applying YBCO CCs to the power electric devices such as transformers and power cables, the reduction of alternating current (AC) loss for long wire is necessary. Multi-filamentation process, which is one of the most effective approaches for AC loss reduction, has been developed by the scribing process. We have developed the filamentation process using chemical etching. MOD derived CCs are, however, easily damaged in the chemical etching process due to existence of pores in a YBCO layer, resulting in critical current (Ic)-degradation and weak delamination strength. Consequently, it is difficult to scribe MOD derived CCs into 1mm-wide filaments for long length using the chemical etching process. Accordingly, we have studied a scribing process using an excimer laser without chemical etching. We defined P' value in this study as a function of irradiated laser power [J] divided by processing speed[m/s]. We studied relationship between the P' value and the results of scribing. It was found that we could scribe the C.C. with a sufficient depth in the condition of large P' value. Furthermore, we found that the Ic was degraded with further increase of the P' value. A 5 mm wide short sample was divided into 10 filaments by the excimer laser scribing process at the P' of 9[J/(m/s)]. The sample revealed reduction of the hysteresis loss down to 1/10 which could be expected from a theoretical prediction using the numbers of the filaments. Ic-degradation was suppressed as 28%, which was smaller than that of the scribed sample using chemical etching (Ic degradation was 38%). Subsequently, we applied the technique to a 100m long YBCO CC. The hysteresis loss of the 100m long MOD derived CC was reduced down to 1/10 (1/the number of filaments) after the multi-filamentation.

  1. Ac-loss measurement of a DyBCO-Roebel assembled coated conductor cable (RACC)

    NASA Astrophysics Data System (ADS)

    Schuller, S.; Goldacker, W.; Kling, A.; Krempasky, L.; Schmidt, C.

    2007-10-01

    Low ac-loss HTS cables for transport currents well above 1 kA are required for application in transformers and generators and are taken into consideration for future generations of fusion reactor coils. Coated conductors (CC) are suitable candidates for high field application at an operation temperature around 50-77 K, which is a crucial precondition for economical cooling costs. We prepared a short length of a Roebel bar cable made of industrial DyBCO coated conductor (Theva Company, Germany). Meander shaped tapes of 4 mm width with a twist pitch of 122 mm were cut from 10 mm wide CC tapes using a specially designed tool. Eleven of these strands were assembled to a cable. The electrical and mechanical connection of the tapes was achieved using a silver powder filled conductive epoxy resin. Ac-losses of a short sample in an external ac field were measured as a function of frequency and field amplitude in transverse and parallel field orientations. In addition, the coupling current time constant of the sample was directly measured.

  2. Low ac loss geometries in YBCO coated conductors and impact on conductor stability

    SciTech Connect

    Duckworth, Robert C; List III, Frederick Alyious; Paranthaman, Mariappan Parans; Rupich, M. W.; Zhang, W.; Xie, Y. Y.; Selvamanickam, V.

    2007-01-01

    Reduction of ac losses in applied ac fields can be accomplished through either the creation of filaments and bridging in YBCO coated conductors or an assembly of narrow width YBCO tapes. The ac losses for each of these geometries were measured at 77 K in perpendicular ac fields up to 100 mT. While ac loss reduction was achieved with YBCO filaments created through laser scribing and inkjet deposition, the assembly of stacked YBCO conductor provides an alternative method of ac loss reduction. When compared to a 4-mm wide YBCO coated conductor with a critical current of 60 A, the ac loss in a stack of 2-mm wide YBCO coated conductors with a similar total critical current was reduced. While the reduction in ac loss in a 2-mm wide stack coincided with the reduction in the engineering current density of the conductor, further reduction of ac loss was obtained through the splicing of the 2-mm wide tapes with low resistance solders. To better determine the practicality of these methods from a stability point of view, a numerical analysis was carried out to determine the influence of bridging and splicing on stability of a YBCO coated conductor for both liquid nitrogen-cooled and conduction cooled geometries.

  3. AC loss measurements in HTS coil assemblies with hybrid coil structures

    NASA Astrophysics Data System (ADS)

    Jiang, Zhenan; Long, Nicholas J.; Staines, Mike; Badcock, Rodney A.; Bumby, Chris W.; Buckley, Robert G.; Amemiya, Naoyuki

    2016-09-01

    Both AC loss and wire cost in coil windings are critical factors for high temperature superconductor (HTS) AC machinery applications. We present AC loss measurement results in three HTS coil assemblies at 77 K and 65 K which have a hybrid coil structure comprising one central winding (CW) and two end windings (EWs) wound with ReBCO and BSCCO wires with different self-field I c values at 77 K. All AC loss results in the coil assemblies are hysteretic and the normalized AC losses in the coil assemblies at different temperatures can be scaled with the I c value of the coil assemblies. The normalised results show that AC loss in a coil assembly with BSCCO CW can be reduced by using EWs wound with high I c ReBCO wires, whilst further AC loss reduction can be achieved by replacing the BSCCO CW with ReBCO CW. The results imply that a flexible hybrid coil structure is possible which considers both AC loss and wire cost in coil assemblies.

  4. Measurements and calculations of transport AC loss in second generation high temperature superconducting pancake coils

    NASA Astrophysics Data System (ADS)

    Yuan, Weijia; Coombs, T. A.; Kim, Jae-Ho; Han Kim, Chul; Kvitkovic, Jozef; Pamidi, Sastry

    2011-12-01

    Theoretical and experimental AC loss data on a superconducting pancake coil wound using second generation (2 G) conductors are presented. An anisotropic critical state model is used to calculate critical current and the AC losses of a superconducting pancake coil. In the coil there are two regions, the critical state region and the subcritical region. The model assumes that in the subcritical region the flux lines are parallel to the tape wide face. AC losses of the superconducting pancake coil are calculated using this model. Both calorimetric and electrical techniques were used to measure AC losses in the coil. The calorimetric method is based on measuring the boil-off rate of liquid nitrogen. The electric method used a compensation circuit to eliminate the inductive component to measure the loss voltage of the coil. The experimental results are consistent with the theoretical calculations thus validating the anisotropic critical state model for loss estimations in the superconducting pancake coil.

  5. The scaling of transport AC losses in Roebel cables with varying strand parameters

    NASA Astrophysics Data System (ADS)

    Jiang, Zhenan; Staines, Mike; Long, Nicholas J.; Badcock, Rodney A.; Bumby, Chris; Talantsev, Evgeny; Hamilton, Kent; Buckley, Robert G.; Amemiya, Naoyuki

    2014-07-01

    A Roebel cable is a good candidate for low-voltage windings in a high-temperature superconductor (HTS) transformer because of its high current-carrying capability and low AC loss. Transport AC loss measurements were carried out in 1.8 m long 15/5 (fifteen 5 mm wide strands) and 15/4 Roebel cables. The results were compared with those in many Roebel cables composed of 2 mm wide Roebel strands. Comparison of the AC losses hinted that the intrinsic difference in normalized transport AC losses is due to differences in the g/w (ratio of the horizontal gap between the Roebel strands over the Roebel strand width) values. The intrinsic difference was confirmed by measuring transport AC loss in a series of horizontally arranged parallel conductor pairs with various g values. A method to scale transport AC losses in Roebel cables with varying strand parameters was developed. The scaling method will be useful for a rough assessment of AC loss in one-layer solenoid winding coils, such as in a HTS transformer.

  6. Calorimetric method of ac loss measurement in a rotating magnetic field.

    PubMed

    Ghoshal, P K; Coombs, T A; Campbell, A M

    2010-07-01

    A method is described for calorimetric ac-loss measurements of high-T(c) superconductors (HTS) at 80 K. It is based on a technique used at 4.2 K for conventional superconducting wires that allows an easy loss measurement in parallel or perpendicular external field orientation. This paper focuses on ac loss measurement setup and calibration in a rotating magnetic field. This experimental setup is to demonstrate measuring loss using a temperature rise method under the influence of a rotating magnetic field. The slight temperature increase of the sample in an ac-field is used as a measure of losses. The aim is to simulate the loss in rotating machines using HTS. This is a unique technique to measure total ac loss in HTS at power frequencies. The sample is mounted on to a cold finger extended from a liquid nitrogen heat exchanger (HEX). The thermal insulation between the HEX and sample is provided by a material of low thermal conductivity, and low eddy current heating sample holder in vacuum vessel. A temperature sensor and noninductive heater have been incorporated in the sample holder allowing a rapid sample change. The main part of the data is obtained in the calorimetric measurement is used for calibration. The focus is on the accuracy and calibrations required to predict the actual ac losses in HTS. This setup has the advantage of being able to measure the total ac loss under the influence of a continuous moving field as experienced by any rotating machines. PMID:20687748

  7. Calorimetric method of ac loss measurement in a rotating magnetic field

    NASA Astrophysics Data System (ADS)

    Ghoshal, P. K.; Coombs, T. A.; Campbell, A. M.

    2010-07-01

    A method is described for calorimetric ac-loss measurements of high-Tc superconductors (HTS) at 80 K. It is based on a technique used at 4.2 K for conventional superconducting wires that allows an easy loss measurement in parallel or perpendicular external field orientation. This paper focuses on ac loss measurement setup and calibration in a rotating magnetic field. This experimental setup is to demonstrate measuring loss using a temperature rise method under the influence of a rotating magnetic field. The slight temperature increase of the sample in an ac-field is used as a measure of losses. The aim is to simulate the loss in rotating machines using HTS. This is a unique technique to measure total ac loss in HTS at power frequencies. The sample is mounted on to a cold finger extended from a liquid nitrogen heat exchanger (HEX). The thermal insulation between the HEX and sample is provided by a material of low thermal conductivity, and low eddy current heating sample holder in vacuum vessel. A temperature sensor and noninductive heater have been incorporated in the sample holder allowing a rapid sample change. The main part of the data is obtained in the calorimetric measurement is used for calibration. The focus is on the accuracy and calibrations required to predict the actual ac losses in HTS. This setup has the advantage of being able to measure the total ac loss under the influence of a continuous moving field as experienced by any rotating machines.

  8. Calorimetric method of ac loss measurement in a rotating magnetic field

    SciTech Connect

    Ghoshal, P. K.; Coombs, T. A.; Campbell, A. M.

    2010-07-15

    A method is described for calorimetric ac-loss measurements of high-T{sub c} superconductors (HTS) at 80 K. It is based on a technique used at 4.2 K for conventional superconducting wires that allows an easy loss measurement in parallel or perpendicular external field orientation. This paper focuses on ac loss measurement setup and calibration in a rotating magnetic field. This experimental setup is to demonstrate measuring loss using a temperature rise method under the influence of a rotating magnetic field. The slight temperature increase of the sample in an ac-field is used as a measure of losses. The aim is to simulate the loss in rotating machines using HTS. This is a unique technique to measure total ac loss in HTS at power frequencies. The sample is mounted on to a cold finger extended from a liquid nitrogen heat exchanger (HEX). The thermal insulation between the HEX and sample is provided by a material of low thermal conductivity, and low eddy current heating sample holder in vacuum vessel. A temperature sensor and noninductive heater have been incorporated in the sample holder allowing a rapid sample change. The main part of the data is obtained in the calorimetric measurement is used for calibration. The focus is on the accuracy and calibrations required to predict the actual ac losses in HTS. This setup has the advantage of being able to measure the total ac loss under the influence of a continuous moving field as experienced by any rotating machines.

  9. Segmented superconducting tape having reduced AC losses and method of making

    DOEpatents

    Foltyn, Stephen R.; Jia, Quanxi; Arendt, Paul N.; Holesinger, Terry G.; Wang, Haiyan

    2009-09-22

    A superconducting tape having reduced AC losses. The tape has a high temperature superconductor layer that is segmented. Disruptive strips, formed in one of the tape substrate, a buffer layer, and the superconducting layer create parallel discontinuities in the superconducting layer that separate the current-carrying elements of the superconducting layer into strips or filament-like structures. Segmentation of the current-carrying elements has the effect of reducing AC current losses. Methods of making such a superconducting tape and reducing AC losses in such tapes are also disclosed.

  10. AC losses in superconducting Nb{sub 3}Sn and NbTi CIC conductors

    SciTech Connect

    Oliva, A.B.; Baudouy, B.J.P.; Miller, J.; Van Sciver, S.W.

    1996-07-01

    AC losses measurements and calculation on large scale Cable-in-Conduit (CIC) conductors have been carried out at NHMFL. In particular samples of the Nb{sub 3}Sn and NbTi conductors developed for the NHMFL 45-T Hybrid Magnet superconducting outsert have been tested. A calorimetric technique involving superfluid helium (He II) has been used. The samples have been tested with applied field variation rates varying in the range between 0.01 T/s to 30 T/s. From results it appears that for most of the samples, at high field variation rates, the coupling currents are so intense to locally saturate the superconducting strands. As no theories describing the saturation regime in CIC conductors exist, the authors tried to extend the theories developed for monolithic conductors to the more complicated CICC geometry. It emerges by defining an effective coupling time constant and an effective radius for the conductor that it is possible to fit the data with good accuracy. Effective coupling time constant and an effective radius for the conductor that it is possible to fit the data with good accuracy. Effective coupling time constants between 3 ms and 200 ms, depending on the strands surface condition and the cable void fraction, have been measured for the Nb{sub 3}Sn conductors, while a time constant of 16 ms has been determined for the NbTi sample. The experimental results and the theoretical analysis are reported in the paper.

  11. Total AC loss study of 2G HTS coils for fully HTS machine applications

    NASA Astrophysics Data System (ADS)

    Zhang, Min; Yuan, Weijia; Kvitkovic, Jozef; Pamidi, Sastry

    2015-11-01

    The application of HTS coils for fully HTS machines has become a new research focus. In the stator of an electrical machine, HTS coils are subjected to a combination of an AC applied current and AC external magnetic field. There is a phase shift between the AC current and AC magnetic field. In order to understand and estimate the total AC loss of HTS coils for electrical machines, we designed and performed a calorimetric measurement for a 2G HTS racetrack coil. Our measurement indicates that the total AC loss is greatly influenced by the phase shift between the applied current and the external magnetic field when the magnetic field is perpendicular to the tape surface. When the applied current and the external magnetic field are in phase, the total AC loss is the highest. When there is a 90 degree phase difference, the total AC loss is the lowest. In order to explain this phenomenon, we employ H formulation and finite element method to model the 2G HTS racetrack coil. Our calculation agrees well with experimental measurements. Two parameters are defined to describe the modulation of the total AC loss in terms of phase difference. The calculation further reveals that the influence of phase difference varies with magnetic field direction. The greatest influence of phase difference is in the perpendicular direction. The study provides key information for large-scale 2G HTS applications, e.g. fully HTS machines and superconducting magnetic energy storage, where the total AC loss subjected to both applied currents and external magnetic fields is a critical parameter for the design.

  12. Using ac dipoles to localize sources of beam coupling impedance

    NASA Astrophysics Data System (ADS)

    Biancacci, N.; Tomás, R.

    2016-05-01

    The beam coupling impedance is one of the main sources of beam instabilities and emittance blow up in circular accelerators. A refined machine impedance evaluation is therefore required in order to understand and model intensity dependent effects and instabilities that may limit the machine performance. For this reason, many impedance source localization techniques have been developed. In this work we present the impedance localization technique based on the observation of phase advance versus intensity at the beam position monitors using ac dipoles to force betatron oscillations. We present analytical formulas for the interpretation of measurements together with simulations to benchmark and illustrate the equations. Studies on the method accuracy for different Fourier transform algorithms are presented as well as first exploratory measurements performed in the LHC.

  13. AC Loss Reduction in Filamentized YBCO Coated Conductors with Virtual Transverse Cross-cuts

    SciTech Connect

    Zhang, Yifei; Duckworth, Robert C; Ha, Tam T; List III, Frederick Alyious; Gouge, Michael J; Chen, Y; X, Xiong,; Selvamanickam, V.

    2011-01-01

    While the performance of YBa{sub 2}Cu{sub 3}O{sub 7-x} (YBCO)-based coated conductors under dc currents has improved significantly in recent years, filamentization is being investigated as a technique to reduce ac loss so that the 2nd generation (2G) high temperature superconducting (HTS) wires can also be utilized in various ac power applications such as cables, transformers and fault current limiters. Experimental studies have shown that simply filamentizing the superconducting layer is not effective enough to reduce ac loss because of incomplete flux penetration in between the filaments as the length of the tape increases. To introduce flux penetration in between the filaments more uniformly and further reduce the ac loss, virtual transverse cross-cuts were made in superconducting filaments of the coated conductors fabricated using the metal organic chemical vapor deposition (MOCVD) method. The virtual transverse cross-cuts were formed by making cross-cuts (17 - 120 {micro}m wide) on the IBAD (ion beam assisted deposition)-MgO templates using laser scribing followed by depositing the superconducting layer ({approx} 0.6 {micro}m thick). AC losses were measured and compared for filamentized conductors with and without the cross-cuts under applied peak ac fields up to 100 mT. The results were analyzed to evaluate the efficacy of filament decoupling and the feasibility of using this method to achieve ac loss reduction.

  14. WITHDRAWN: Complex Study of Transport AC Loss in Various 2G HTS Racetrack Coils

    NASA Astrophysics Data System (ADS)

    Chen, Yiran; Zhang, Min; Chudy, Michal; Matsuda, Koichi; Coombs, Tim

    2013-06-01

    HTS racetrack coils are becoming important elements of an emerging number of superconducting devices such as generators or motors. In these devices the issue of AC loss is crucial, as performance and cooling power are derived from this quantity. This paper presents a comparative study of transport AC loss in two different types of 2G HTS racetrack coils. In this study, both experimental measurements and computer simulation approaches were employed. All the experiments were performed using classical AC electrical method. The finite-element computer model was used to estimate electromagnetic properties and calculate transport AC loss. The main difference between the characterized coils is covered inside tape architectures. While one coil uses tape based on RABITS magnetic substrate, the second coil uses a non-magnetic tape. Ferromagnetic loss caused by a magnetic substrate is an important issue involved in the total AC loss. As a result, the coil with the magnetic substrate surprised with high AC loss and rather low performance.

  15. Complex study of transport AC loss in various 2G HTS racetrack coils

    NASA Astrophysics Data System (ADS)

    Chen, Yiran; Zhang, Min; Chudy, Michal; Matsuda, Koichi; Coombs, Tim

    2013-04-01

    HTS racetrack coils are becoming important elements of an emerging number of superconducting devices such as generators or motors. In these devices the issue of AC loss is crucial, as performance and cooling power are derived from this quantity. This paper presents a comparative study of transport AC loss in two different types of 2G HTS racetrack coils. In this study, both experimental measurements and computer simulation approaches were employed. All the experiments were performed using classical AC electrical method. The finite-element computer model was used to estimate electromagnetic properties and calculate transport AC loss. The main difference between the characterized coils is covered inside tape architectures. While one coil uses tape based on RABITS magnetic substrate, the second coil uses a non-magnetic tape. Ferromagnetic loss caused by a magnetic substrate is an important issue involved in the total AC loss. As a result, the coil with the magnetic substrate surprised with high AC loss and rather low performance.

  16. Calculating AC Losses in High-temperature Superconducting Cables Comprising Coated Conductors

    NASA Astrophysics Data System (ADS)

    Noji, Hideki; Kawano, Shouta; Akaki, Yoji; Hamada, Tsugio

    In this study, we present a new calculation model of AC loss in a high-temperature superconducting (HTS) cable comprising coated conductors. AC loss is calculated by an electric circuit (EC) model. A previous EC model had three circuit elements: resistance as a function of the layer current, inductances related to the circumferential and axial fields. The new EC model has only inductances, and resistance is eliminated. In both models, AC loss of the coated conductor in each layer of an HTS cable is calculated on the basis of the Norris equation for a thin strip. The differences between measurement and calculations using the previous and new models are 12% and 14%, respectively, when transporting 1 kArms, which indicates that the new model is applicable for the calculation of AC loss in an HTS cable. These results indicate that layer current is dependent on inductances and not on resistance. The elimination of resistance simplifies AC loss calculation because it does not require repeated calculations for the convergence of the layer current. The calculation time was 1/20th of that of the previous model. In the new model, the Norris equation can be replaced with the calculation result obtained by the two-dimensional finite element method to obtain more accurate AC loss.

  17. Ac loss characteristics of YBCO superconducting tapes fabricated by TFA-MOD technique

    NASA Astrophysics Data System (ADS)

    Iwakuma, Masataka; Nigo, Masahiro; Inoue, Daisuke; Miyamoto, Naoya; Kiss, Takanobu; Funaki, Kazuo; Iijima, Yasuhiro; Saitoh, Takashi; Izumi, Teruo; Yamada, Yutaka; Shiohara, Yuu

    2005-10-01

    We investigated the ac loss properties of a YBCO superconducting tape fabricated by TFA-MOD technique. The thickness of the YBCO layer is 1.2 μm. A 6-tape stack of 50 mm in length and 10 mm in width was inserted into a saddle-shaped pickup coil. The ac loss was measured at 35-77 K by applying an external ac magnetic field. The magnetic field angle was changed by rotating the sample stack around its longitudinal axis. The effective penetration field, which corresponds to the breaking point of an ac loss curve, decreased with increasing field angle though it was much smaller than that which was estimated for a superconducting slab with the same thickness as the width of a tape. As a result, the ac loss increased monotonically with an increasing field angle against the wide surface for any amplitude. The observed field angular dependence of the ac loss agreed with the theoretically predicted one by using the observed ac losses in perpendicular magnetic field. Anyway the ac loss for a larger amplitude than the effective penetration field was proportional to the critical current density and the projective width of a tape in the direction of the applied magnetic field for any field angle and any temperature as well known. In addition we estimated the magnetic field, B, dependence of the critical current, Ic, from the observed magnetization curves. It was shown that zero-field Ic appeared to be a linear function of temperature and Ic-B characteristics was scaled with zero-field Ic. We also discussed a difference in Ic-B characteristics and its temperature dependence between TFA-MOD tapes and IBAD-PLD ones.

  18. Structural and AC loss study for pure and doped MgB2 superconductor

    NASA Astrophysics Data System (ADS)

    Hansdah, J. S.; Sarun, P. M.

    2015-06-01

    Superconducting polycrystalline bulk MgB2 samples doped with n-C, n-Y2O3 and n-Ho2O3 were prepared by powder-in-sealed (PIST) method. XRD measurement shows the influence of dopants on phase and lattice parameters of samples. The ac susceptibility measurement reveals ac loss and activation energy of the samples. Nano-C doped sample shows less ac loss in all frequency (208 Hz - 999 Hz) among the doped samples; whereas n-Ho2O3 doped sample shows highest ac loss. The activation energy is high for rare earth (n-Y2O3 and n-Ho2O3) doped samples as compare to n-C doped samples which reveals the enhancement in flux-pinning properties of these materials.

  19. Structural and AC loss study for pure and doped MgB{sub 2} superconductor

    SciTech Connect

    Hansdah, J. S.; Sarun, P. M.

    2015-06-24

    Superconducting polycrystalline bulk MgB{sub 2} samples doped with n-C, n-Y{sub 2}O{sub 3} and n-Ho{sub 2}O{sub 3} were prepared by powder-in-sealed (PIST) method. XRD measurement shows the influence of dopants on phase and lattice parameters of samples. The ac susceptibility measurement reveals ac loss and activation energy of the samples. Nano-C doped sample shows less ac loss in all frequency (208 Hz – 999 Hz) among the doped samples; whereas n-Ho{sub 2}O{sub 3} doped sample shows highest ac loss. The activation energy is high for rare earth (n-Y{sub 2}O{sub 3} and n-Ho{sub 2}O{sub 3}) doped samples as compare to n-C doped samples which reveals the enhancement in flux-pinning properties of these materials.

  20. AC loss in high-temperature superconducting conductors, cables and windings for power devices

    NASA Astrophysics Data System (ADS)

    Oomen, M. P.; Rieger, J.; Hussennether, V.; Leghissa, M.

    2004-05-01

    High-temperature superconducting (HTS) transformers and reactor coils promise decreased weight and volume and higher efficiency. A critical design parameter for such devices is the AC loss in the conductor. The state of the art for AC-loss reduction in HTS power devices is described, starting from the loss in the single HTS tape. Improved tape manufacturing techniques have led to a significant decrease in the magnetization loss. Transport-current loss is decreased by choosing the right operating current and temperature. The role of tape dimensions, filament twist and resistive matrix is discussed and a comparison is made between state-of-the-art BSCCO and YBCO tapes. In transformer and reactor coils the AC loss in the tape is influenced by adjacent tapes in the coil, fields from other coils, overcurrents and higher harmonics. These factors are accounted for by a new AC-loss prediction model. Field components perpendicular to the tape are minimized by optimizing the coil design and by flux guidance pieces. High-current windings are made of Roebel conductors with transposed tapes. The model iteratively finds the temperature distribution in the winding and predicts the onset of thermal instability. We have fabricated and tested several AC windings and used them to validate the model. Now we can confidently use the model as an engineering tool for designing HTS windings and for determining the necessary tape properties.

  1. Theory of AC Loss in Cables with 2G HTS Wire

    SciTech Connect

    Clem, J.R.; Malozemoff, A.P.

    2009-09-13

    While considerable work has been done to understand AC losses in power cables made of first generation (1G) high temperature superconductor (HTS) wires, use of second generation (2G) HTS wires brings in some new considerations. The high critical current density of the HTS layer 2G wire reduces the surface superconductor hysteretic losses. Instead, gap and polygonal losses, flux transfer losses in imbalanced two layer cables and ferromagnetic losses for wires with NiW substrates constitute the principal contributions. Current imbalance and losses associated with the magnetic substrate can be minimized by orienting the substrates of the inner winding inward and the outer winding outward.

  2. Modelling and measurement of ac loss in BSCCO/Ag-tape windings

    NASA Astrophysics Data System (ADS)

    Oomen, M. P.; Nanke, R.; Leghissa, M.

    2003-03-01

    High-temperature superconducting (HTS) transformers promise decreased weight and volume and higher efficiency. A 1 MVA HTS railway transformer was built and tested at Siemens AG. This paper deals with the prediction of ac loss in the BSCCO/Ag-tape windings. In a railway transformer the tape carries ac current in alternating field, the temperature differs from 77 K, tapes are stacked or cabled and overcurrents and higher harmonics occur. In ac-loss literature these issues are treated separately, if at all. We have developed a model that predicts the ac loss in sets of BSCCO/Ag-tape coils, and deals with the above-mentioned issues. The effect of higher harmonics on the loss in HTS tapes is considered for the first time. The paper gives a complete overview of the model equations and required input parameters. The model is validated over a wide range of the input parameters, using the measured critical current and ac loss of single tapes, single coils and sets of coils in the 1 MVA transformer. An accuracy of around 25% is achieved in all relevant cases. Presently the model is developed further, in order to describe other HTS materials and other types of applications.

  3. Low AC Loss YBCO Coated Conductor Geometry by Direct Inkjet Printing

    SciTech Connect

    Rupich, Martin, Dr.; Duckworth, Robert, Dr.

    2009-10-01

    The second generation (2G) high temperature superconductors (HTS) wire offers potential benefits for many electric power applications, including ones requiring filamentized conductors with low ac loss, such as transformers and fault current limiters. However, the use of 2G wire in these applications requires the development of both novel multi-filamentary conductor designs with lower ac losses and the development of advanced manufacturing technologies that enable the low-cost manufacturing of these filamentized architectures. This Phase I SBIR project focused on testing inkjet printing as a potential low-cost, roll-to-roll manufacturing technique to fabricate potential low ac loss filamentized architectures directly on the 2G template strips.

  4. AC loss measurement of superconducting dipole magnets by the calorimetric method

    SciTech Connect

    Morita, Y.; Hara, K.; Higashi, N.; Kabe, A.

    1996-12-31

    AC losses of superconducting dipole magnets were measured by the calorimetric method. The magnets were model dipole magnets designed for the SSC. These were fabricated at KEK with 50-mm aperture and 1.3-m overall length. The magnet was set in a helium cryostat and cooled down to 1.8 K with 130 L of pressurized superfluid helium. Heat dissipated by the magnet during ramp cycles was measured by temperature rise of the superfluid helium. Heat leakage into the helium cryostat was 1.6 W and was subtracted from the measured heat to obtain AC loss of the magnet. An electrical measurement was carried out for calibration. Results of the two methods agreed within the experimental accuracy. The authors present the helium cryostat and measurement system in detail, and discuss the results of AC loss measurement.

  5. Transport ac losses of a second-generation HTS tape with a ferromagnetic substrate and conducting stabilizer

    NASA Astrophysics Data System (ADS)

    Li, Shuo; Chen, Du-Xing; Fang, Jin

    2015-12-01

    The current-voltage curve and transport ac loss of a second-generation HTS tape with a ferromagnetic NiW substrate and brass stabilizer are measured. It is found that the ac loss is up to two orders of magnitude larger than what is expected by the power-law E(J) determined by the current-voltage curve and increases with increasing frequency. Modeling results show that the overly large ac loss is contributed by the ac loss in the HTS strip enhanced by the NiW substrate and the magnetic hysteresis loss in the substrate, and the frequency-dependent loss occurs in the brass layer covering the substrate but not in the ferromagnetic substrate itself as assumed previously. The ac loss in the brass layer is associated with transport currents but not eddy currents, and it has some features similar to ordinary eddy-current loss with significant differences.

  6. Distribution of AC loss in a HTS magnet for SMES with different operating conditions

    NASA Astrophysics Data System (ADS)

    Xu, Y.; Tang, Y.; Ren, L.; Jiao, F.; Song, M.; Cao, K.; Wang, D.; Wang, L.; Dong, H.

    2013-11-01

    The AC loss induced in superconducting tape may affect the performance of a superconducting device applied to power system, such as transformer, cable, motor and even Superconducting Magnetic Energy Storage (SMES). The operating condition of SMES is changeable due to the need of compensation to the active or reactive power according to the demand of a power grid. In this paper, it is investigated that the distribution of AC loss for a storage magnet on different operating conditions, which is based on finite element method (FEM) and measured properties of BSCCO/Ag tapes. This analytical method can be used to optimize the SMES magnet.

  7. Second VAMAS a.c. loss measurement intercomparison: magnetization measurement of low-frequency (hysteretic) a.c. loss in NbTi multifilamentary strands

    NASA Astrophysics Data System (ADS)

    Collings, E. W.; Sumption, M. D.; Itoh, K.; Wada, H.; Tachikawa, K.

    The results of the 2 nd VAMAS measurement intercomparison program on low-frequency (hysteretic) a.c. loss are presented and discussed. Two sets of multifilamentary NbTi strands (Set No. 1: copper matrix, fil. diams 0.5, 1, 3, and 12 μm; Set No. 2: cupronickel matrix, fil. diams 0.4, 0.5, and 1 μm) were subjected to interlaboratory testing. In an initial series of tests, samples in various forms (e.g. wire bundles, coils) were measured mostly by vibrating-sample- and SQUID magnetometry. Considerable scatter was noted especially in the small-filament-diameter a.c.-loss data. In a study of measurement accuracy, a supplementary series of tests compared the results of VSM measurement of a given pair of copper-matrix samples. In the light of all the results, factors contributing to a.c. loss error are discussed and recommendations are made concerning the specification of future a.c.-loss measurement intercomparisons.

  8. Depinning of flux lines and AC losses in magnet-superconductor levitation system

    SciTech Connect

    Terentiev, A. N.; Hull, J. R.; De Long, L. E.

    1999-11-29

    The AC loss characteristics of a magnet-superconductor system were studied with the magnet fixed to the free end of an oscillating cantilever located near a stationary melt-textured YBCO pellet. Below a threshold AC field amplitude {approx}2Oe, the dissipation of the oscillator is amplitude-independent, characteristic of a linear, non-hysteretic regime. Above threshold,dissipation increases with amplitude, reflecting the depinning and hysteretic motion of flux lines. The threshold AC field is an order of magnitude higher than that measured for the same YBCO material via AC susceptometry in a uniform DC magnetic field, A partial lock-in of flux lines between YBCO ab planes is proposed as the mechanism for the substantial increase of the depinning threshold.

  9. AC losses in prototype multistrand conductors for warm dielectric cable designs

    SciTech Connect

    Willis, J. O.; Maley, M. P.; Boening, H. J.; Coletta, G.; Mele, R.; Nassi, M.

    2002-01-01

    We report on multiphase ac losses in four-layer prototype multi-strand conductors (PMCs) wound from EITS tape provided by American Superconductor Corporation. These conductors are prototypes warm dielectric cable designs, such as for the US Dept. of Energy's Superconductivity Partnership Initiative Project at Detroit Edison, We report on single phase 'two phaset'(no current in Ihe PMC but with an external ac magnetic field generated by the two normal Conductors arranged at the remaining corners of an equilateral triangle forming a three-phase configuration) ,and balanced three phase losses. Losses were also measured using a set of saddle coils to apply an ac magnetic field to the PMC. The losses were measured as a function of temperature, frequency, and current. We compare the losses for three PMCs, one (4LA) wound conventionally with equal pitch angles for all layers and the two others (4LB and 4LC) wound to achieve equal current distribution (UCD) among the layers, and thus lower singlephase losses in the operating region. In addition, 4LC was wound with a newer gcneration tape having a higher critical current. The PMC 4LC was found to have the lowest single, twophase, and three-phase losses.

  10. AC-loss considerations of a pulse SMES for an accelerator

    NASA Astrophysics Data System (ADS)

    Lyly, M.; Hiltunen, I.; Järvelä, J.; Korpela, A.; Lehti, L.; Stenvall, A.; Mikkonen, R.

    2010-06-01

    In particle accelerators quasi-DC superconducting magnets are used to keep particles in desired tracks. The needed rapid field variations of these high energy magnets require large energy bursts. If these bursts are taken from and fed back to the utility grid, its voltage is distorted and the quality of the electricity degrades. In addition, these bursts may decrease operation life time of generators and extra arrangements may be required by the electricity producers. Thus, an energy storage is an essential component for a cost-effective particle accelerator. Flywheels, capacitors and superconducting magnetic energy storage (SMES) are possible options for these relatively large and high power energy storages. Here we concentrate on AC-loss of a pulse SMES aiming to demonstrate the feasibility of NbTi SMES in a particle accelerator. The designing of a SMES requires highly reliable AC-loss simulations. In this paper, calorimetric AC-loss measurements of a NbTi magnet have been carried out to consider conductor's suitability in a pulse SMES. In addition, the measured results are compared with AC-loss simulations.

  11. The influence of bending strains on AC power losses in multifilamentary BSCCO-2223/Ag tapes

    NASA Astrophysics Data System (ADS)

    Tsukamoto, O.; Ciszek, M.; Suzuki, H.; Ogawa, J.

    2006-08-01

    Recent advances in the manufacturing of multifilamentary high temperature superconducting composite wires allow for wider practical applications of the conductors, e.g. in power transmission cables, transformers and motors. The wires, based mainly on BSCCO-2223 and YBCO-123 cuprates, are used in the forms of variously shaped coils; therefore they are subjected to different kinds of mechanical stresses and strains. These, in turn, lead to some changes in the physical parameters of the superconducting material, mainly in the critical current density, and thus in the dissipated electromagnetic energy, when subjected to changing magnetic fields and transport currents. In this work we report some experimental results related to the AC loss characteristics of Bi-2223/Ag multifilamentary tapes and their dependences on bending strains. These losses are compared to the losses of virgin, straight tapes. The total AC losses, i.e. transport current and magnetization losses, in the Bi-2223/Ag tapes, were measured by means of the electrical and calorimetric methods. The experimental data obtained are compared with the critical state model predictions for AC loss behaviour in the experimental conditions presented here.

  12. Theory of ac loss in power transmission cables with second generation high temperature superconductor wires

    SciTech Connect

    Clem, J. R.; Malozemoff, A. P.

    2010-02-22

    While a considerable amount of work has been done in an effort to understand ac losses in power transmission cables made of first generation high temperature superconductor (HTS) wires, use of second generation (2G) HTS wires brings in some new considerations. The high critical current density of the HTS layer in 2G wires reduces the surface superconductor hysteretic losses, for which a new formula is derived. Instead, gap and polygonal losses, flux transfer losses in imbalanced two-layer cables and ferromagnetic losses for wires with NiW substrates constitute the principal contributions. A formula for the flux transfer losses is also derived with a paramagnetic approximation for the substrate. Current imbalance and losses associated with the magnetic substrate can be minimized by orienting the substrates of the inner winding inward and the outer winding outward.

  13. Numerical and theoretical evaluations of AC losses for single and infinite numbers of superconductor strips with direct and alternating transport currents in external AC magnetic field

    NASA Astrophysics Data System (ADS)

    Kajikawa, K.; Funaki, K.; Shikimachi, K.; Hirano, N.; Nagaya, S.

    2010-11-01

    AC losses in a superconductor strip are numerically evaluated by means of a finite element method formulated with a current vector potential. The expressions of AC losses in an infinite slab that corresponds to a simple model of infinitely stacked strips are also derived theoretically. It is assumed that the voltage-current characteristics of the superconductors are represented by Bean’s critical state model. The typical operation pattern of a Superconducting Magnetic Energy Storage (SMES) coil with direct and alternating transport currents in an external AC magnetic field is taken into account as the electromagnetic environment for both the single strip and the infinite slab. By using the obtained results of AC losses, the influences of the transport currents on the total losses are discussed quantitatively.

  14. Artificial neural networks for AC losses prediction in superconducting round filaments

    NASA Astrophysics Data System (ADS)

    Leclerc, J.; Makong Hell, L.; Lorin, C.; Masson, P. J.

    2016-06-01

    An extensive and fast method to estimate superconducting AC losses within a superconducting round filament carrying an AC current and subjected to an elliptical magnetic field (both rotating and oscillating) is presented. Elliptical fields are present in rotating machine stators and being able to accurately predict AC losses in fully superconducting machines is paramount to generating realistic machine designs. The proposed method relies on an analytical scaling law (ASL) combined with two artificial neural network (ANN) estimators taking 9 input parameters representing the superconductor, external field and transport current characteristics. The ANNs are trained with data generated by finite element (FE) computations with a commercial software (FlexPDE) based on the widely accepted H-formulation. After completion, the model is validated through comparison with additional randomly chosen data points and compared for simple field configurations to other predictive models. The loss estimation discrepancy is about 3% on average compared to the FEA analysis. The main advantages of the model compared to FE simulations is the fast computation time (few milliseconds) which allows it to be used in iterated design processes of fully superconducting machines. In addition, the proposed model provides a higher level of fidelity than the scaling laws existing in literature usually only considering pure AC field.

  15. AC losses and heat removal in three-dimensional winding pack of Samsung superconducting test facility under pulsed magnetic field operation

    NASA Astrophysics Data System (ADS)

    Wang, Qiuliang; Seong Yoon, Cheon; Baang, Sungkeun; Kim, Myungkyu; Park, Hyunki; Kim, Yongjin; Lee, Sangil; Kim, Keeman

    2001-04-01

    The Samsung superconducting test facility (SSTF) will be operated under the highly pulsed field to simulate the operating conditions of KSTAR. An analysis has been performed to study the transient heat removal characteristics and temperature margin for the main, blip and compensating coils in the SSTF. This method is based on a quasi-three-dimensional model, which the thermal coupling of turn-to-turn, pancake-to-pancake and channel-to-channel is taken into account, to simulate the conductor temperature rise and the thermal expansion of supercritical helium due to the high AC losses under the pulsed field. The local AC losses, which include coupling loss, eddy current loss and hysteresis loss in the cable-in-conduit conductor, are estimated. The temperature margin, mass flow rate, distribution of AC losses are studied under the given operating scenario. The mass flow reduction and peak temperature rise depending on the inlet pressure and inlet position of CICC are studied. It is shown that the initial mass flow rate remarkably influences on the peak temperature of superconducting strands. The large mass flow rate can reduce the temperature rise when the inlet of helium is located at the high field region. By contrast, because of heat induced flow to improve the cooling condition of the superconducting strands, the small initial mass flow rate results in the low peak temperature in strands when the inlet of helium is located at the low field region.

  16. Self-field ac losses in biaxially aligned Y{endash}Ba{endash}Cu{endash}O tape conductors

    SciTech Connect

    Iijima, Y.; Hosaka, M.; Sadakata, N.; Saitoh, T.; Kohno, O.; Takeda, K.

    1997-11-01

    Self-field ac losses were measured by the conventional ac four-probe method in biaxially aligned Y{endash}Ba{endash}Cu{endash}O tapes using polycrystalline Hastelloy tapes with textured yttria-stabilized-zirconia buffer layers. The ac losses increased in proportion to the fourth power of transport current in the high J{sub c} sample, and agreed well with Norris{close_quote} equation for thin strip conductors. However, the low J{sub c} sample had rather higher losses than Norris{close_quote} prediction, suggesting excessive magnetic flux penetration caused by percolated current paths. The results confirmed Norris{close_quote} prediction of the low ac losses for thin strip conductors, and indicated the importance of removing percolated structures of current paths to avoid higher ac losses than the theoretical predictions based on uniform conductors. {copyright} {ital 1997 American Institute of Physics.}

  17. Single and three-phase AC losses in HTS superconducting power transmission line prototype cables

    SciTech Connect

    Daney, D.E.; Boenig, H.J.; Maley, M.P.; Coulter, J.Y.; Fleshler, S.

    1997-11-01

    AC losses in two, one-meter-long lengths of HTS prototype multi-strand conductors (PMC`s) are measured with a temperature-difference calorimeter. Both single-phase and three-phase losses are examined with ac currents up to 1,000 A rms. The calorimeter, designed specifically for these measurements, has a precision of 1 mW. PMC {number_sign}1 has two helically-wound, non-insulated layers of HTS tape (19 tapes per layer), each layer wrapped with opposite pitch. PMC {number_sign}2 is identical except for insulation between the layers. The measured ac losses show no significant effect of interlayer insulation and depend on about the third power of the current--a result in agreement with the Bean-Norris model adapted to the double-helix configuration. The three-phase losses are a factor of two higher than those exhibited by a single isolated conductor, indicating a significant interaction between phases.

  18. Transport and AC loss properties of the repaired multifilamentary REBCO superconducting tapes

    NASA Astrophysics Data System (ADS)

    Yamasaki, S.; Iwakuma, M.; Funaki, K.; Kato, J.; Chikumoto, T.; Tanabe, K.; Nakao, K.; Izumi, T.; Yamada, Y.; Shiohara, Y.; Saito, T.

    2010-11-01

    For near-future applications of REBa 2Cu 3O 7 (REBCO) coated conductors to electric power cables, transformers and Superconducting Magnetic Energy Storage (SMES), the long taped wires with high performance in the transport properties have been designed and fabricated. Moreover, in order to drastically reduce AC losses in perpendicular field configuration, advanced multifilament YBCO coated conductors (MFYCCs) fabricated with technique of a laser scribing process have been also developed. In the present study, from engineering viewpoints to utilize such advanced conductors, we evaluated the transport and AC loss properties of short MFYCCs with a repaired part or a joint by a diffusion joint technique with the saddle-shaped pickup coil method.

  19. Inkjet printing of multifilamentary YBCO for low AC loss coated conductors

    NASA Astrophysics Data System (ADS)

    Hopkins, S. C.; Joseph, D.; Mitchell-Williams, T. B.; Calleja, A.; Vlad, V. R.; Vilardell, M.; Ricart, S.; Granados, X.; Puig, T.; Obradors, X.; Usoskin, A.; Falter, M.; Bäcker, M.; Glowacki, B. A.

    2014-05-01

    Considerable progress has been made with the development of REBCO coated conductors in recent years, and high performance conductors are available commercially. For many applications, however, the cost remains prohibitive, and AC losses discourage their selection for higher frequency applications. Chemical solution deposition (CSD) methods are attractive for low-cost, scalable preparation of buffer and superconductor layers, and in many respects inkjet printing is the method of choice, permitting non-contact deposition with minimal materials wastage and excellent control of coating thickness. Highly textured coatings of YBCO and Gd-doped CeO2 have previously been reported on buffered metal substrates. Inkjet printing also introduces the possibility of patterning - directly depositing two and three dimensional structures without subtractive processing - offering a low-cost route to coated conductors with reduced AC losses. In this contribution, the inkjet deposition of superconducting YBCO tracks is reported on industrially relevant buffered metal substrates both by direct printing and an inverse patterning approach. In the latter approach, ceria tracks were printed reported, which are a candidate both for resistive filament spacers and buffer layers. TFA-based precursor solutions have been printed on SS/ABAD-YSZ/CeO2 and Ni-W/LZO/CeO2 RABiTS substrates, and the resulting multifilamentary samples characterised by microscopy and scanning Hall probe measurements. The prospects for future inkjet-printed low AC loss coated conductors are discussed, including control of interfilamentary resistivity and bridging, transposed filamentary structures and stabilisation material.

  20. Numerical study on AC loss characteristics of superconducting power transmission cables comprising coated conductors with magnetic substrates

    NASA Astrophysics Data System (ADS)

    Amemiya, N.; Nakahata, M.

    2007-10-01

    Electromagnetic field analyses were made for mono-layer conductors comprising coated conductors for superconducting power transmission cables in order to evaluate their AC loss characteristics. We focused on the magnetic properties of the substrates of coated conductors. The current distribution in each coated conductor and the magnetic flux profile around each coated conductor were visualized. The influence of relative permeability and the space between coated conductors on the AC loss characteristics of mono-layer conductors were studied based on the visualized current and magnetic flux distributions. The influence of a saturated magnetic property on a calculated AC loss was also discussed.

  1. A flux-coupled ac/dc magnetizing device

    NASA Astrophysics Data System (ADS)

    Gopman, D. B.; Liu, H.; Kent, A. D.

    2013-06-01

    We report on an instrument for applying ac and dc magnetic fields by capturing the flux from a rotating permanent magnet and projecting it between two adjustable pole pieces. This can be an alternative to standard electromagnets for experiments with small samples or in probe stations in which an applied magnetic field is needed locally, with advantages that include a compact form-factor, very low power requirements and dissipation as well as fast field sweep rates. This flux capture instrument (FLUXCAP) can produce fields from -400 to +400 mT, with field resolution less than 1 mT. It generates static magnetic fields as well as ramped fields, with ramping rates as high as 10 T/s. We demonstrate the use of this apparatus for studying the magnetotransport properties of spin-valve nanopillars, a nanoscale device that exhibits giant magnetoresistance.

  2. First thin AC-coupled silicon strip sensors on 8-inch wafers

    NASA Astrophysics Data System (ADS)

    Bergauer, T.; Dragicevic, M.; König, A.; Hacker, J.; Bartl, U.

    2016-09-01

    The Institute of High Energy Physics (HEPHY) in Vienna and the semiconductor manufacturer Infineon Technologies Austria AG developed a production process for planar AC-coupled silicon strip sensors manufactured on 200 μm thick 8-inch p-type wafers. In late 2015, the first wafers were delivered featuring the world's largest AC-coupled silicon strip sensors. Detailed electrical measurements were carried out at HEPHY, where single strip and global parameters were measured. Mechanical studies were conducted and the long-term behavior was investigated using a climate chamber. Furthermore, the electrical properties of various test structures were investigated to validate the quality of the manufacturing process.

  3. Approach for Wide Use of Diagnostic Method for XLPE Cables Using Harmonics in AC Loss Current

    NASA Astrophysics Data System (ADS)

    Tsujimoto, Tomiyuki; Nakade, Masahiko; Yagi, Yukihiro; Ishii, Noboru

    Water tree is one of the degradation aspects of XLPE cables used for under-ground distribution or transmission lines. We have developed the loss current method using 3rd harmonic in AC loss current for cable diagnosis. Harmonic components in loss current arise as a result of the non-linear voltage-current characteristics of water trees. We confirmed that the 3rd harmonic in AC loss current had good correlation with water tree growth and break down strength. After that, we have applied this method to the actual 66kV XLPE cable lines. Up to now, the number of the application results is more than 130 lines. In case of cable lines terminated at gas-insulated switchgear (GIS), we have to remove the lightning arrestor (LA) and the potential transformer (PT) out of the test circuit. The reason is that we are afraid that each of LA and PT disturbs the degradation signal from cable lines. It takes extra time (1 or 2 days) and costs more to remove LA and PT in GIS out of a circuit. In order to achieve easy and reasonable diagnosis, we have developed a new method for cable lines terminated at GIS, by utilizing a technique, which enables to reduce signal of LA and PT from disturbed signal of cable lines. We confirmed the effect of the new method by experiments with actual cables.

  4. AC loss reduction of TFA-MOD coated conductors in long length by laser scribing technique

    NASA Astrophysics Data System (ADS)

    Katayama, K.; Hirano, H.; Machi, T.; Takagi, Y.; Takahashi, Y.; Izumi, T.

    TFA-MOD process is expected to be promising for future applications since it can produce high performance YBCO coated conductors with low cost. Applying YBCO coated conductors to the power electric devices such as transformer, cable, motors, reduction of AC loss for long wire is necessary. Multifilamentation, which is one of the effective approaches for AC loss reduction, has been developed by the scribing process. YBCO coated conductors produced by our standard TFA-MOD process delaminated into two parts by the laser scribing. The delamination was clarified to occur within the superconducting layer caused by the defects such as pores in the superconducting layer. In order to reduce the defects in the superconducting layer, we modify the heat treatment profile performed on the decomposed precursor films by applying the interim annealing(550-600°C) before crystallization heat treatment(740-770°C). The interim annealed samples had much less and smaller pores than the standard processed ones. The peel strength measured by transverse tensile test was as high as the PLD derived coated conductors which was successfully scribed into five filaments resulting in 1/5 AC loss. A 50m long YBCO coated conductor with the characteristics of 398A/cmwidth was obtained and cut into 5 mm width, followed by the laser scribing process into five filaments. The multifilamentation process was successfully performed without delamination throughout the wire. The hysteresis loss was down to 1/N (N: number of filaments), as we aimed. The IC properties of the filaments were 29±4A, indicating the wire was uniformly fabricated.

  5. Finite element analysis of current flowing patterns and AC loss in the multifilament strand

    NASA Astrophysics Data System (ADS)

    Ta, Wurui; Li, Yingxu; Gao, Yuanwen

    2013-12-01

    Intrinsic current flow and field distribution scheme under the imposed low current injection and the applied weak field is meaningful to interpret Ic degradation and AC loss in a strand that performs as a normal composite conductor. A 2D finite element (FE) transport model is built in COMSOL to identify the various transverse resistance components and reveal the interrelation among them. Then the transverse resistivity components are taken as the basic electrical components in a 3D composite strand model. The 3D model follows the realistic trajectories of twisted filaments in strand composite and experimental material properties. To address the potential/current map in the stationary transport, the FE model is thoroughly analyzed for the short-sample and long-sample strand, imposed by two in-plane steady current injections and a potential boundary condition at one strand end with the other end grounded, respectively. The results show that the short-sample longitudinal current is uniform with little resistivity loss, and flows from the positive source and converges to the negative one in the cross section with different paths and current proportions between filaments and matrix. However, for the long-sample, there is a serious reduction in electric potential along the strand axis and the currents mostly concentrate on filaments. The time-varying problem is also implemented by computing AC loss induced by a relatively far-away alternating line current. It is discussed where appropriate that the effect of the twist pitch and contact resistivity on the pattern and magnitude of the current flow and AC loss.

  6. AC loss in stacks of Bi-2223/Ag tapes modified with ferromagnetic covers at the edges

    NASA Astrophysics Data System (ADS)

    Safran, S.; Gömöry, F.; Gencer, Ali

    2010-10-01

    We investigated the magnetization loss of stacked Bi-2223/Ag tapes with a ferromagnetic cover on the edges. Such modification has been found recently to reduce the AC loss of a single tape; however, the behavior in a coil winding could be different. With experiments and numerical calculations we show that a ferromagnetic cover on the edges of a superconducting tape could reduce its magnetization loss also when the tapes are arranged in a stack. The effect is weaker for larger numbers of tapes but nevertheless remained significant in a stack of four tapes, which was the maximum number studied here. The effects observed experimentally are nicely explained by the results of numerical calculations.

  7. Analytic formulation for the ac electrical conductivity in two- temperature, strongly coupled, overdense plasma: FORTRAN subroutine

    SciTech Connect

    Cauble, R.; Rozmus, W.

    1993-10-21

    A FORTRAN subroutine for the calculation of the ac electrical conductivity in two-temperature, strongly coupled, overdense plasma is presented. The routine is the result of a model calculation based on classical transport theory with application to plasmas created by the interaction of short pulse lasers and solids. The formulation is analytic and the routine is self-contained.

  8. Ac45 silencing mediated by AAV-sh-Ac45-RNAi prevents both bone loss and inflammation caused by periodontitis

    PubMed Central

    Zhu, Zheng; Chen, Wei; Hao, Liang; Zhu, Guochun; Lu, Yun; Li, Sheng; Wang, Lin; Li, Yi-Ping

    2015-01-01

    Aim Periodontitis induced by oral pathogens leads to severe periodontal tissue damage and osteoclast-mediated bone resorption caused by inflammation. Based on the importance of Ac45 in osteoclast formation and function, we performed this study to evaluate the therapeutic potential of periodontitis by local adeno-associated virus (AAV)-mediated Ac45 gene knockdown. Material and Methods We used AAV-mediated short hairpin RNAi knockdown of Ac45 gene expression (AAV-sh-Ac45) to inhibit bone erosion and gingival inflammation simultaneously in a well-established periodontitis mouse model induced by Porphyromonas gingivalis W50. Histological studies were performed to evaluate the bone protection of AAV-sh-Ac45. Immunochemistry, ELISA and qRT-PCR were performed to reveal the role of Ac45 knockdown on inflammation, immune response and expression of cytokine. Results We found that Ac45 knockdown impaired osteoclast-mediated extracellular acidification and bone resorption in vitro and in vivo. Furthermore, local administration of AAV-sh-Ac45 protected mice from bone erosion by >85% and attenuated inflammation and decreased infiltration of T-cells, dendritic cells and macrophages in the periodontal lesion. Notably, the expression of pro-inflammatory cytokines was also reduced. Conclusions Local AAV-sh-Ac45 gene therapy efficiently protects against periodontal tissue damage and bone erosion through both inhibition of osteoclast function and attenuating inflammation, and may represent a powerful new treatment strategy for periodontitis. PMID:25952706

  9. Volumetric loss quantification using ultrasonic inductively coupled transducers

    NASA Astrophysics Data System (ADS)

    Gong, Peng; Hay, Thomas R.; Greve, David W.; Oppenheim, Irving J.

    2015-03-01

    The pulse-echo method is widely used for plate and pipe thickness measurement. However, the pulse echo method does not work well for detecting localized volumetric loss in thick-wall tubes, as created by erosion damage, when the morphology of volumetric loss is irregular and can reflect ultrasonic pulses away from the transducer, making it difficult to detect an echo. In this paper, we propose a novel method using an inductively coupled transducer to generate longitudinal waves propagating in a thick-wall aluminum tube for the volumetric loss quantification. In the experiment, longitudinal waves exhibit diffraction effects during the propagation which can be explained by the Huygens-Fresnel principle. The diffractive waves are also shown to be significantly delayed by the machined volumetric loss on the inside surface of the thick-wall aluminum tube. It is also shown that the inductively coupled transducers can generate and receive similar ultrasonic waves to those from wired transducers, and the inductively coupled transducers perform as well as the wired transducers in the volumetric loss quantification when other conditions are the same.

  10. Graphene-coated coupling coil for AC resistance reduction

    DOEpatents

    Miller, John M

    2014-03-04

    At least one graphene layer is formed to laterally surround a tube so that the basal plane of each graphene layer is tangential to the local surface of the tube on which the graphene layer is formed. An electrically conductive path is provided around the tube for providing high conductivity electrical path provided by the basal plane of each graphene layer. The high conductivity path can be employed for high frequency applications such as coupling coils for wireless power transmission to overcome skin depth effects and proximity effects prevalent in high frequency alternating current paths.

  11. Coupling loss time constants in full-size Nb{sub 3}Sn CIC model conductors for fusion magnets

    SciTech Connect

    Nijhuis, A.; Kate, H.H.J. ten; Duchateau, J.L.

    1997-06-01

    The cable-in-conduit conductor for the ITER coils have to perform at magnetic fields up to 13 T under the conditions of normal high ramp rates as well as extreme magnetic pulses during a plasma disruption. Modelling, ac loss computations and design optimisations require to understand and identify the coupling loss time constants in multistage cables. For this AC loss measurements are performed on jacketed full size Nb{sub 3}Sn cable-in-conduit conductors. A transverse sinusoidal magnetic field is applied on the conductor to determine the coupling loss time constants with a calorimetric method. Moreover the decay of the coupling currents after a linear ramp is monitored with compensated pick-up coils. A comparison is made between the results obtained with both measuring methods. It appears that the n.{tau} value taken from the slope of the loss versus frequency curve in the low frequency limit has only a meaning at these low frequencies. At higher rates of magnetic field change which are relevant to describe a plasma disruption, internal shielding effects are not negligible and a different approach has to be used. The experimental results and a straightforward model are presented to find the coupling current time constants of this type of conductors. It is shown that several dominant time constants can exist that are associated with relatively small volume fractions of a cable.

  12. ESBWR response to an extended station blackout/loss of all AC power

    SciTech Connect

    Barrett, A. J.; Marquino, W.

    2012-07-01

    U.S. federal regulations require light water cooled nuclear power plants to cope with Station Blackouts for a predetermined amount of time based on design factors for the plant. U.S. regulations define Station Blackout (SBO) as a loss of the offsite electric power system concurrent with turbine trip and unavailability of the onsite emergency AC power system. According to U.S. regulations, typically the coping period for an SBO is 4 hours and can be as long as 16 hours for currently operating BWR plants. Being able to cope with an SBO and loss of all AC power is required by international regulators as well. The U.S. licensing basis for the ESBWR is a coping period of 72 hours for an SBO based on U.S. NRC requirements for passive safety plants. In the event of an extended SBO (viz., greater than 72 hours), the ESBWR response shows that the design is able to cope with the event for at least 7 days without AC electrical power or operator action. ESBWR is a Generation III+ reactor design with an array of passive safety systems. The ESBWR primary success path for mitigation of an SBO event is the Isolation Condenser System (ICS). The ICS is a passive, closed loop, safety system that initiates automatically on a loss of power. Upon Station Blackout or loss of all AC power, the ICS begins removing decay heat from the Reactor Pressure Vessel (RPV) by (i) condensing the steam into water in heat exchangers located in pools of water above the containment, and (ii) transferring the decay heat to the atmosphere. The condensed water is then returned by gravity to cool the reactor again. The ICS alone is capable of maintaining the ESBWR in a safe shutdown condition after an SBO for an extended period. The fuel remains covered throughout the SBO event. The ICS is able to remove decay heat from the RPV for at least 7 days and maintains the reactor in a safe shutdown condition. The water level in the RPV remains well above the top of active fuel for the duration of the SBO event

  13. Flux Pinning and AC Loss in Second Generation High Temperature Superconductor Wires

    SciTech Connect

    Paranthaman, Mariappan Parans; Selvamanickam, V.

    2007-01-01

    Major advances have been made in the last 18 years in high-temperature superconductor (HTS) reserach and development, resulting in increased use of HTS materials in commerical and pre-commercial electric-power applications. This new and important book addresses the issues related to flux pinning, AC losses and thick YBCO film growth. Written by top most scientists in the world, it presents the current status and issues related to YBCO coated conductors and the need for further fundamental materials science work in YBCO coated conductor. It will be a useful handbook for years to come.

  14. Stability mechanical considerations, and AC loss in HTSC monoliths, coils, and wires

    NASA Technical Reports Server (NTRS)

    Sumption, M. D.; Collings, E. W.

    1995-01-01

    For monolithic high-T(sub c) superconductors (HTSC's) calculations are presented of: (1) the initial flux jump field, H(sub fj), in melt-processed YBCO based on a field and temperature dependent J(sub c), and (2) the radial and circumferential stresses in solid and hollow cylinders containing trapped magnetic flux. For model multi filamentary (MF) HTSC/Ag strands calculations are presented of: (1) the limiting filament diameters for adiabatic and dynamic stability, and (2) the hysteretic and eddy current components of AC loss. Again for MF HTSC/Ag composite strands the need for filamentary subdivision and twisting is discussed.

  15. Calculating transport AC losses in stacks of high temperature superconductor coated conductors with magnetic substrates using FEM

    NASA Astrophysics Data System (ADS)

    Ainslie, Mark D.; Flack, Tim J.; Campbell, Archie M.

    2012-01-01

    In this paper, the authors investigate the electromagnetic properties of stacks of high temperature superconductor (HTS) coated conductors with a particular focus on calculating the total transport AC loss. The cross-section of superconducting cables and coils is often modeled as a two-dimensional stack of coated conductors, and these stacks can be used to estimate the AC loss of a practical device. This paper uses a symmetric two dimensional (2D) finite element model based on the H formulation, and a detailed investigation into the effects of a magnetic substrate on the transport AC loss of a stack is presented. The number of coated conductors in each stack is varied from 1 to 150, and three types of substrate are compared: non-magnetic weakly magnetic and strongly magnetic. The non-magnetic substrate model is comparable with results from existing models for the limiting cases of a single tape (Norris) and an infinite stack (Clem). The presence of a magnetic substrate increases the total AC loss of the stack, due to an increased localized magnetic flux density, and the stronger the magnetic material, the further the flux penetrates into the stack overall. The AC loss is calculated for certain tapes within the stack, and the differences and similarities between the losses throughout the stack are explained using the magnetic flux penetration and current density distributions in those tapes. The ferromagnetic loss of the substrate itself is found to be negligible in most cases, except for small magnitudes of current. Applying these findings to practical applications, where AC transport current is involved, superconducting coils should be wound where possible using coated conductors with a non-magnetic substrate to reduce the total AC loss in the coil.

  16. FAST COMPENSATION OF GLOBAL LINEAR COUPLING IN RHIC USING AC DIPOLES.

    SciTech Connect

    CALAGA, R.; FRANCHI, A. , TOMAS, R.

    2006-06-26

    Global linear coupling has been extensively studied in accelerators and several methods have been developed to compensate the coupling coefficient C using skew quadrupole families scans. However, scanning techniques can become very time consuming especially during the commissioning of an energy ramp. In this paper they illustrate a new technique to measure and compensate, in a single machine cycle, global linear coupling from turn-by-turn BPM data without the need of a skew quadrupole scan. The algorithm is applied to RHIC BPM data using AC dipoles and compared with traditional methods.

  17. The effect of surface grain reversal on the AC losses of sintered Nd-Fe-B permanent magnets

    NASA Astrophysics Data System (ADS)

    Moore, Martina; Roth, Stefan; Gebert, Annett; Schultz, Ludwig; Gutfleisch, Oliver

    2015-02-01

    Sintered Nd-Fe-B magnets are exposed to AC magnetic fields in many applications, e.g. in permanent magnet electric motors. We have measured the AC losses of sintered Nd-Fe-B magnets in a closed circuit arrangement using AC fields with root mean square-values up to 80 mT (peak amplitude 113 mT) over the frequency range 50 to 1000 Hz. Two magnet grades with different dysprosium content were investigated. Around the remanence point the low grade material (1.7 wt% Dy) showed significant hysteresis losses; whereas the losses in the high grade material (8.9 wt% Dy) were dominated by classical eddy currents. Kerr microscopy images revealed that the hysteresis losses measured for the low grade magnet can be mainly ascribed to grains at the sample surface with multiple domains. This was further confirmed when the high grade material was subsequently exposed to DC and AC magnetic fields. Here a larger number of surface grains with multiple domains are also present once the step in the demagnetization curve attributed to the surface grain reversal is reached and a rise in the measured hysteresis losses is evident. If in the low grade material the operating point is slightly offset from the remanence point, such that zero field is not bypassed, its AC losses can also be fairly well described with classical eddy current theory.

  18. First experience with the new Coupling Loss Induced Quench system

    NASA Astrophysics Data System (ADS)

    Ravaioli, E.; Datskov, V. I.; Dudarev, A. V.; Kirby, G.; Sperin, K. A.; ten Kate, H. H. J.; Verweij, A. P.

    2014-03-01

    New-generation high-field superconducting magnets pose a challenge relating to the protection of the coil winding pack in the case of a quench. The high stored energy per unit volume calls for a very efficient quench detection and fast quench propagation in order to avoid damage due to overheating. A new protection system called Coupling-Loss Induced Quench (CLIQ) was recently developed and tested at CERN. This method provokes a fast change in the magnet transport current by means of a capacitive discharge. The resulting change in the local magnetic field induces inter-filament and inter-strand coupling losses which heat up the superconductor and eventually initiate a quench in a large fraction of the coil winding pack. The method is extensively tested on a Nb-Ti single-wire test solenoid magnet in the CERN Cryogenic Laboratory in order to assess its performance, optimize its operating parameters, and study new electrical configurations. Each parameter is thoroughly analyzed and its impact on the quench efficiency highlighted. Furthermore, an alternative method is also considered, based on a CLIQ discharge through a resistive coil magnetically coupled with the solenoid but external to it. Due to the strong coupling between the external coil and the magnet, the oscillating current in the external coil changes the magnetic field in the solenoid strands and thus generates coupling losses in the strands. Although for a given charging voltage this configuration usually yields poorer quench performance than a standard CLIQ discharge, it has the advantage of being electrically insulated from the solenoid coil, and thus it can work with much higher voltage.

  19. Transport ac loss in a rectangular thin strip with power-law E (J) relation

    NASA Astrophysics Data System (ADS)

    Li, Shuo; Chen, Du-Xing; Fan, Yu; Fang, Jin

    2015-01-01

    Transport ac losses of a rectangular thin strip obeying relation E /Ec =(J /Jc) n with a fixed critical current Ic and n = 5, 10, 20, 30 , and 40 are accurately computed at a fixed frequency f as functions of the current amplitude Im . The results may be interpolated and scaled to those at any values of Ic, f , and 5 ⩽ n ⩽ 40 . Normalized in the same way as that in Norris' analytical formula derived from the critical-state model and converting f to a critical frequency fc , the modeling results may be better compared with the Norris formula and experimental data. A complete set of calculated modeling data are given with necessary formulas to be easily used by experimentalists in any particular case.

  20. Transport ac loss of elliptical thin strips with a power-law E(J) relation

    NASA Astrophysics Data System (ADS)

    Jia, Chen-Xi; Chen, Du-Xing; Li, Shuo; Fang, Jin

    2015-10-01

    The transport ac loss Q of an elliptical thin strip of critical current I c with a power-law relation E\\propto {J}n is accurately computed as a function of current amplitude I m and frequency f. The resulting Q({I}m) is normalized to q({i}m) following the Norris critical-state formula, and converted to {q}*({i}m*) at a critical frequency f c based on a transport scaling law. Having a set of {q}*({i}m*) at several values of n as a base, a general expression of {q}*({i}m*,n) is obtained, which can be used to easily calculate q({i}m) for any practical purposes.

  1. Galvanic coupling between D6AC steel, 6061-T6 aluminum, Inconel 718 and graphite-epoxy composite material: Corrosion occurrence and prevention

    NASA Technical Reports Server (NTRS)

    Danford, M. D.; Higgins, R. H.

    1983-01-01

    The effects of galvanic coupling between D6AC steel, 6061-T6 aluminum, Inconel 718, and graphite-epoxy composite material (G/E) in 3.5% NaCl were studied. Measurements of corrosion potentials, galvanic currents and corrosion rates of the bare metals using weight-loss methods served to establish the need for corrosion protection in cases where D6AC steel and 6061-T6 aluminum are galvanically coupled to G/E in salt water while Inconel 718 was shown to be compatible with G/E. Six tests were made to study corrosion protective methods for eliminating galvanic corrosion in the cases of D6AC steel and 6061-T6 aluminum coupled to G/E. These results indicate that, when the G/E is completely coated with paint or a paint/polyurethane resin combination, satisfactory protection of the D6AC steel is achieved with either a coat of zinc-rich primer or a primer/topcoat combination. Likewise, satisfactory corrosion protection of the aluminum is achieved by coating it with an epoxy coating system.

  2. Analysis and comparison for rotor eddy current losses of permanent magnet synchronous generator according to dc and ac load conditions

    NASA Astrophysics Data System (ADS)

    Jang, Seok-Myeong; Kim, Hyun-Kyu; Choi, Jang-Young; Ko, Kyoung-Jin

    2009-04-01

    This paper presents an analytical procedure for the calculation of the eddy current losses of permanent magnet synchronous generator (PMSG). The dc and ac loading effects on the eddy current is examined through the suggested analytical procedure that considers the radial and tangential flux density waveform through a phase current harmonic analysis. The corresponding test results are also presented to quantify and compare those loading effects on the eddy current. The results verified the suggested analytical procedures and show that the rotor eddy current losses for PMSG with the dc loads turned out to be more significant than those with the ac loads.

  3. ac losses and field and current density distribution during a full cycle of a stack of superconducting tapes

    NASA Astrophysics Data System (ADS)

    Yuan, Weijia; Campbell, A. M.; Coombs, T. A.

    2010-05-01

    Starting from an existing model by Clem et al., this paper has analyzed how the current density and magnetic field distribution of a stack of superconducting tapes with ac transport currents or applied fields will change in a full cycle. This paper assumes when the ac current or field starts to change in the other direction, a new penetrated region will begin to penetrate from the superconductor surface. If we assume Jc is constant in the critical region, this paper demonstrates that the Claassen formula (7) can be used to calculate the exact ac losses. If Jc depends on local Bz, we can use Eq. (9) to quickly predict the ac losses. This approach does not need to calculate a complete ac cycle. This saves considerably computation time while gives a result which is in close agreement with that calculated from a complete ac cycle. The calculation method can be applied for calculating a superconducting pancake coil if the coil radius is much larger than the tape width.

  4. Ac loss modelling and measurement of superconducting transformers with coated-conductor Roebel-cable in low-voltage winding

    NASA Astrophysics Data System (ADS)

    Pardo, Enric; Staines, Mike; Jiang, Zhenan; Glasson, Neil

    2015-11-01

    Power transformers using a high temperature superconductor (HTS) ReBCO coated conductor and liquid nitrogen dielectric have many potential advantages over conventional transformers. The ac loss in the windings complicates the cryogenics and reduces the efficiency, and hence it needs to be predicted in its design, usually by numerical calculations. This article presents detailed modelling of superconducting transformers with Roebel cable in the low-voltage (LV) winding and a high-voltage (HV) winding with more than 1000 turns. First, we model a 1 MVA 11 kV/415 V 3-phase transformer. The Roebel cable solenoid forming the LV winding is also analyzed as a stand-alone coil. Agreement between calculations and experiments of the 1 MVA transformer supports the model validity for a larger tentative 40 MVA 110 kV/11 kV 3-phase transformer design. We found that the ac loss in each winding is much lower when it is inserted in the transformer than as a stand-alone coil. The ac loss in the 1 and 40 MVA transformers is dominated by the LV and HV windings, respectively. Finally, the ratio of total loss over rated power of the 40 MVA transformer is reduced below 40% of that of the 1 MVA transformer. In conclusion, the modelling tool in this work can reliably predict the ac loss in real power applications.

  5. How filaments can reduce AC losses in HTS coated conductors: a review

    NASA Astrophysics Data System (ADS)

    Grilli, Francesco; Kario, Anna

    2016-08-01

    Second-generation high-temperature superconductor (HTS) tapes, known also as coated conductors, are very promising tapes for HTS applications, in virtue of their extremely high critical current density, in-field behavior, and mechanical strength. Yet, the extremely large (typically in the range 1000–10 000) width-to-thickness ratio of the superconducting material makes them prone to high power dissipation in the presence of time-varying magnetic fields perpendicular to their flat face—a condition frequently met in several applications. Since the dissipation is directly proportional to the square of the superconductor's width, an obvious way of reducing it is by striating the superconductor into narrow filaments (stripes): in that case, provided that the filaments are electromagnetically uncoupled, the losses are reduced by a factor equal to the number of filaments. In the past two decades, many researchers from groups around the world have tried to apply this idea to practical conductors using different techniques. The aim of this paper is to provide a review of such efforts, focusing on the different approaches to make filamentized conductors, on the effectiveness of the AC loss reduction, and on the applicability of those techniques to long lengths.

  6. Calorimetric AC loss measurement of MgB2 superconducting tape in an alternating transport current and direct magnetic field

    NASA Astrophysics Data System (ADS)

    See, K. W.; Xu, X.; Horvat, J.; Cook, C. D.; Dou, S. X.

    2012-11-01

    Applications of MgB2 superconductors in electrical engineering have been widely reported, and various studies have been made to define their alternating current (AC) losses. However, studies on the transport losses with an applied transverse DC magnetic field have not been conducted, even though this is one of the favored conditions in applications of practical MgB2 tapes. Methods and techniques used to characterize and measure these losses have so far been grouped into ‘electrical’ and ‘calorimetric’ approaches with external conditions set to resemble the application conditions. In this paper, we present a new approach to mounting the sample and employ the calorimetric method to accurately determine the losses in the concurrent application of AC transport current and DC magnetic fields that are likely to be experienced in practical devices such as generators and motors. This technique provides great simplification compared to the pickup coil and lock-in amplifier methods and is applied to a long length (˜10 cm) superconducting tape. The AC loss data at 20 and 30 K will be presented in an applied transport current of 50 Hz under external DC magnetic fields. The results are found to be higher than the theoretical predictions because of the metallic fraction of the tape that contributes quite significantly to the total losses. The data, however, will allow minimization of losses in practical MgB2 coils and will be used in the verification of numerical coil models.

  7. AC losses in a finite Z stack using an anisotropic homogeneous-medium approximation

    NASA Astrophysics Data System (ADS)

    Clem, John R.; Claassen, J. H.; Mawatari, Yasunori

    2007-12-01

    A finite stack of thin superconducting tapes, all carrying a fixed current I, can be approximated by an anisotropic superconducting bar with critical current density Jc = Ic/2aD, where Ic is the critical current of each tape, 2a is the tape width, and D is the tape-to-tape periodicity. The current density J must obey the constraint \\int J\\, \\mathrm {d}x=I/D , where the tapes lie parallel to the x axis and are stacked along the z axis. We suppose that Jc is independent of field (Bean approximation) and look for a solution to the critical state for arbitrary height 2b of the stack. For c<|x|losses depend only weakly on how c is chosen. We argue that for small D/a the anisotropic homogeneous-medium approximation gives a reasonably accurate estimate of the ac losses in a finite Z stack. The results for a Z stack can be used to calculate the transport losses in a pancake coil wound with superconducting tape.

  8. Digital DC-Reconstruction of AC-Coupled Electrophysiological Signals with a Single Inverting Filter

    PubMed Central

    Schmid, Ramun; Leber, Remo; Schmid, Hans-Jakob; Generali, Gianluca

    2016-01-01

    Since the introduction of digital electrocardiographs, high-pass filters have been necessary for successful analog-to-digital conversion with a reasonable amplitude resolution. On the other hand, such high-pass filters may distort the diagnostically significant ST-segment of the ECG, which can result in a misleading diagnosis. We present an inverting filter that successfully undoes the effects of a 0.05 Hz single pole high-pass filter. The inverting filter has been tested on more than 1600 clinical ECGs with one-minute durations and produces a negligible mean RMS-error of 3.1*10−8 LSB. Alternative, less strong inverting filters have also been tested, as have different applications of the filters with respect to rounding of the signals after filtering. A design scheme for the alternative inverting filters has been suggested, based on the maximum strength of the filter. With the use of the suggested filters, it is possible to recover the original DC-coupled ECGs from AC-coupled ECGs, at least when a 0.05 Hz first order digital single pole high-pass filter is used for the AC-coupling. PMID:26938769

  9. Angular Dependence of Transport AC Losses in Superconducting Wire with Position-Dependent Critical Current Density in a DC Magnetic Field

    NASA Astrophysics Data System (ADS)

    Su, Xing-liang; Xiong, Li-ting; Gao, Yuan-wen; Zhou, You-he

    2013-07-01

    Transport AC losses play a very important role in high temperature superconductors (HTSs), which usually carry AC transport current under applied magnetic field in typical application-like conditions. In this paper, we propose the analytical formula for transport AC losses in HTS wire by considering critical current density of both inhomogeneous and anisotropic field dependent. The angular dependence of critical current density is described by effective mass theory, and the HTS wire has inhomogeneous distribution cross-section of critical current density. We calculate the angular dependence of normalized AC losses under different DC applied magnetic fields. The numerical results of this formula agree well with the experiment data and are better than the results of Norris formula. This analytical formula can explain the deviation of experimental transport current losses from the Norris formula and apply to calculate transport AC losses in realistic practical condition.

  10. Statistical analysis of intrinsic and extrinsic coupling losses for step-index polymer optical fibers.

    PubMed

    Werzinger, Stefan; Bunge, Christian-Alexander

    2015-08-24

    The intrinsic and extrinsic coupling losses of step-index polymer optical fibers are statistically examined by Monte Carlo simulations. In contrast to most existing models that linearly scale individual losses, a comprehensive analytic coupling loss model is used that also considers the interdependencies between mismatches in numerical aperture and core diameter, as well as radial and longitudinal offsets. As a typical example, the coupling losses of A4a.2 step-index multimode fibers are analyzed for an equilibrium mode distribution. The results show considerably less conservative coupling loss estimations than with traditional models, improving link power budgeting. PMID:26368203

  11. Optimization of ITER Nb3Sn CICCs for coupling loss, transverse electromagnetic load and axial thermal contraction

    NASA Astrophysics Data System (ADS)

    Nijhuis, A.; van Lanen, E. P. A.; Rolando, G.

    2012-01-01

    The ITER cable-in-conduit conductors (CICCs) are built up from sub-cable bundles, wound in different stages, which are twisted to counter coupling loss caused by time-changing external magnet fields. The selection of the twist pitch lengths has major implications for the performance of the cable in the case of strain-sensitive superconductors, i.e. Nb3Sn, as the electromagnetic and thermal contraction loads are large but also for the heat load from the AC coupling loss. At present, this is a great challenge for the ITER central solenoid (CS) CICCs and the solution presented here could be a breakthrough for not only the ITER CS but also for CICC applications in general. After proposing longer twist pitches in 2006 and successful confirmation by short sample tests later on, the ITER toroidal field (TF) conductor cable pattern was improved accordingly. As the restrictions for coupling loss are more demanding for the CS conductors than for the TF conductors, it was believed that longer pitches would not be applicable for the conductors in the CS coils. In this paper we explain how, with the use of the TEMLOP model and the newly developed models JackPot-ACDC and CORD, the design of a CICC can be improved appreciably, particularly for the CS conductor layout. For the first time a large improvement is predicted not only providing very low sensitivity to electromagnetic load and thermal axial cable stress variations but at the same time much lower AC coupling loss. Reduction of the transverse load and warm-up-cool-down degradation can be reached by applying longer twist pitches in a particular sequence for the sub-stages, offering a large cable transverse stiffness, adequate axial flexibility and maximum allowed lateral strand support. Analysis of short sample (TF conductor) data reveals that increasing the twist pitch can lead to a gain of the effective axial compressive strain of more than 0.3% with practically no degradation from bending. This is probably explained by

  12. Numerical models for ac loss calculation in large-scale applications of HTS coated conductors

    NASA Astrophysics Data System (ADS)

    Quéval, Loïc; Zermeño, Víctor M. R.; Grilli, Francesco

    2016-02-01

    Numerical models are powerful tools to predict the electromagnetic behavior of superconductors. In recent years, a variety of models have been successfully developed to simulate high-temperature-superconducting (HTS) coated conductor tapes. While the models work well for the simulation of individual tapes or relatively small assemblies, their direct applicability to devices involving hundreds or thousands of tapes, e.g., coils used in electrical machines, is questionable. Indeed, the simulation time and memory requirement can quickly become prohibitive. In this paper, we develop and compare two different models for simulating realistic HTS devices composed of a large number of tapes: (1) the homogenized model simulates the coil using an equivalent anisotropic homogeneous bulk with specifically developed current constraints to account for the fact that each turn carries the same current; (2) the multi-scale model parallelizes and reduces the computational problem by simulating only several individual tapes at significant positions of the coil’s cross-section using appropriate boundary conditions to account for the field generated by the neighboring turns. Both methods are used to simulate a coil made of 2000 tapes, and compared against the widely used H-formulation finite-element model that includes all the tapes. Both approaches allow faster simulations of large number of HTS tapes by 1-3 orders of magnitudes, while maintaining good accuracy of the results. Both models can therefore be used to design and optimize large-scale HTS devices. This study provides key advancement with respect to previous versions of both models. The homogenized model is extended from simple stacks to large arrays of tapes. For the multi-scale model, the importance of the choice of the current distribution used to generate the background field is underlined; the error in ac loss estimation resulting from the most obvious choice of starting from a uniform current distribution is revealed.

  13. The magnetisation profiles and ac magnetisation losses in a single layer YBCO thin film caused by travelling magnetic field waves

    NASA Astrophysics Data System (ADS)

    Wang, Wei; Coombs, Timothy

    2015-05-01

    This paper studies the magnetisation and ac magnetisation losses caused by a travelling magnetic wave on a single-layer YBCO thin film. This work provides thorough investigations on how the critical magnetic field gradient has been changed by the application of a travelling wave. Several conditions were studied such as zero-field cooling (ZFC), field cooling (FC) and a delta-shaped trapped field. It was found that the travelling wave tends to attenuate the existing critical magnetic field gradients in all these conditions. This interesting magnetic behaviour can be well predicted by the finite element (FEM) software with the E-J power law and Maxwell’s equations. The numerical simulations show that the existing critical current density has been compromised after applying the travelling wave. The magnetisation profile caused by the travelling wave is very different from the standing wave, while the magnetisation based on the standing wave can be interpreted by the Bean model and constant current density assumption. Based on the numerical method, which has reliability that has been solidly proven in the study, we have extended the study to the ac magnetisation losses. Comparisons were made between the travelling wave and the standing wave for this specific YBCO sample. It was found that by applying the magnetic wave of the same amplitude, the ac magnetisation loss caused by the travelling wave is about 1/3 of that caused by the standing wave. These results are helpful in understanding the general magnetism problems and ac magnetisation loss in the travelling magnetic wave conditions such as inside a high temperature superconducting (HTS) rotating machine, etc.

  14. Inter-strand current sharing and ac loss measurements in superconducting YBCO Roebel cables

    SciTech Connect

    Majoros, M.; Sumption, M. D.; Collings, E. W.; Long, N. J.

    2015-04-08

    A Roebel cable, one twist pitch long, was modified from its as-received state by soldering copper strips between the strands to provide inter-strand connections enabling current sharing. Various DC transport currents (representing different percentages of its critical current) were applied to a single strand of such a modified cable at 77 K in a liquid nitrogen bath. Simultaneous monitoring of I–V curves in different parts of the strand as well as in its interconnections with other strands was made using a number of sensitive Keithley nanovoltmeters in combination with a multichannel high-speed data acquisition card, all controlled via LabView software. Current sharing onset was observed at about 1.02 of strand Ic. At a strand current of 1.3Ic about 5% of the current was shared through the copper strip interconnections. A finite element method modeling was performed to estimate the inter-strand resistivities required to enable different levels of current sharing. The relative contributions of coupling and hysteretic magnetization (and loss) were compared, and for our cable and tape geometry, and at dB/dt=1 T s-1, and our inter-strand resistance of 0.77 mΩ, (enabling a current sharing of 5% at 1.3Ic) the coupling component was 0.32% of the hysteretic component. However, inter-strand contact resistance values of 100–1000 times smaller (close to those of NbTi and Nb3Sn based accelerator cables) would make the coupling components comparable in size to the hysteretic components.

  15. Inter-strand current sharing and ac loss measurements in superconducting YBCO Roebel cables

    DOE PAGESBeta

    sumption, Mike; Majoros, Milan; Collings, E. W.; Van der Laan, D. C.

    2014-11-07

    A Roebel cable, one twist pitch long, was modified from its as-received state by soldering copper strips between the strands to provide inter-strand connections enabling current sharing. Various DC transport currents (representing different percentages of its critical current) were applied to a single strand of such a modified cable at 77 K in a liquid nitrogen bath. Simultaneous monitoring of I–V curves in different parts of the strand as well as in its interconnections with other strands was made using a number of sensitive Keithley nanovoltmeters in combination with a multichannel high-speed data acquisition card, all controlled via LabView software.more » Current sharing onset was observed at about 1.02 of strand Ic. At a strand current of 1.3Ic about 5% of the current was shared through the copper strip interconnections. A finite element method modeling was performed to estimate the inter-strand resistivities required to enable different levels of current sharing. The relative contributions of coupling and hysteretic magnetization (and loss) were compared, and for our cable and tape geometry, and at dB/dt=1 T s-1, and our inter-strand resistance of 0.77 mΩ, (enabling a current sharing of 5% at 1.3Ic ) the coupling component was 0.32% of the hysteretic component. However, inter-strand contact resistance values of 100–1000 times smaller (close to those of NbTi and Nb3Sn based accelerator cables) would make the coupling components comparable in size to the hysteretic components.« less

  16. Inter-strand current sharing and ac loss measurements in superconducting YBCO Roebel cables

    DOE PAGESBeta

    Majoros, M.; Sumption, M. D.; Collings, E. W.; Long, N. J.

    2015-04-08

    A Roebel cable, one twist pitch long, was modified from its as-received state by soldering copper strips between the strands to provide inter-strand connections enabling current sharing. Various DC transport currents (representing different percentages of its critical current) were applied to a single strand of such a modified cable at 77 K in a liquid nitrogen bath. Simultaneous monitoring of I–V curves in different parts of the strand as well as in its interconnections with other strands was made using a number of sensitive Keithley nanovoltmeters in combination with a multichannel high-speed data acquisition card, all controlled via LabView software.more » Current sharing onset was observed at about 1.02 of strand Ic. At a strand current of 1.3Ic about 5% of the current was shared through the copper strip interconnections. A finite element method modeling was performed to estimate the inter-strand resistivities required to enable different levels of current sharing. The relative contributions of coupling and hysteretic magnetization (and loss) were compared, and for our cable and tape geometry, and at dB/dt=1 T s-1, and our inter-strand resistance of 0.77 mΩ, (enabling a current sharing of 5% at 1.3Ic) the coupling component was 0.32% of the hysteretic component. However, inter-strand contact resistance values of 100–1000 times smaller (close to those of NbTi and Nb3Sn based accelerator cables) would make the coupling components comparable in size to the hysteretic components.« less

  17. Inter-strand current sharing and ac loss measurements in superconducting YBCO Roebel cables

    NASA Astrophysics Data System (ADS)

    Majoros, M.; Sumption, M. D.; Collings, E. W.; Long, N. J.

    2015-05-01

    A Roebel cable, one twist pitch long, was modified from its as-received state by soldering copper strips between the strands to provide inter-strand connections enabling current sharing. Various DC transport currents (representing different percentages of its critical current) were applied to a single strand of such a modified cable at 77 K in a liquid nitrogen bath. Simultaneous monitoring of I-V curves in different parts of the strand as well as in its interconnections with other strands was made using a number of sensitive Keithley nanovoltmeters in combination with a multi-channel high-speed data acquisition card, all controlled via LabView software. Current sharing onset was observed at about 1.02 of strand Ic. At a strand current of 1.3Ic about 5% of the current was shared through the copper strip interconnections. A finite element method modeling was performed to estimate the inter-strand resistivities required to enable different levels of current sharing. The relative contributions of coupling and hysteretic magnetization (and loss) were compared, and for our cable and tape geometry, and at dB/dt = 1 T s-1, and our inter-strand resistance of 0.77 mΩ, (enabling a current sharing of 5% at 1.3Ic ) the coupling component was 0.32% of the hysteretic component. However, inter-strand contact resistance values of 100-1000 times smaller (close to those of NbTi and Nb3Sn based accelerator cables) would make the coupling components comparable in size to the hysteretic components.

  18. Inter-strand current sharing and ac loss measurements in superconducting YBCO Roebel cables

    SciTech Connect

    sumption, Mike; Majoros, Milan; Collings, E. W.; Van der Laan, D. C.

    2014-11-07

    A Roebel cable, one twist pitch long, was modified from its as-received state by soldering copper strips between the strands to provide inter-strand connections enabling current sharing. Various DC transport currents (representing different percentages of its critical current) were applied to a single strand of such a modified cable at 77 K in a liquid nitrogen bath. Simultaneous monitoring of I–V curves in different parts of the strand as well as in its interconnections with other strands was made using a number of sensitive Keithley nanovoltmeters in combination with a multichannel high-speed data acquisition card, all controlled via LabView software. Current sharing onset was observed at about 1.02 of strand Ic. At a strand current of 1.3Ic about 5% of the current was shared through the copper strip interconnections. A finite element method modeling was performed to estimate the inter-strand resistivities required to enable different levels of current sharing. The relative contributions of coupling and hysteretic magnetization (and loss) were compared, and for our cable and tape geometry, and at dB/dt=1 T s-1, and our inter-strand resistance of 0.77 mΩ, (enabling a current sharing of 5% at 1.3Ic ) the coupling component was 0.32% of the hysteretic component. However, inter-strand contact resistance values of 100–1000 times smaller (close to those of NbTi and Nb3Sn based accelerator cables) would make the coupling components comparable in size to the hysteretic components.

  19. Rabi oscillations at different tunnel couplings for an ac-gated quantum dot qubit

    NASA Astrophysics Data System (ADS)

    Thorgrimsson, Brandur; Kim, Dohun; Simmons, C. B.; Ward, Daniel R.; Foote, Ryan H.; Savage, D. E.; Lagally, M. G.; Friesen, Mark; Coppersmith, S. N.; Eriksson, M. A.

    2015-03-01

    One way to create a qubit is to use two distinct positions of a single electron as qubit states. Such a system can be achieved by using the left and right positions in a gated double quantum dot. In this system the qubit is strongly coupled to electric fields and has potential for high-speed operations. By tuning specific gate voltages, the tunnel coupling between the left and right quantum dots can be changed. Here, by using resonant ac microwave driving and gate tuning, we explore variations of T2* and the Rabi frequency on the tunnel coupling and microwave drive power, and we study strong driving effects such as generation of second harmonics. This work was supported in part by ARO (W911NF-12-0607) and NSF (DMR-1206915 and PHY-1104660). Development and maintenance of the growth facilities used for fabricating samples is sup- ported by DOE (DE-FG02-03ER46028). This research utilized NSF-supported shared facilities at the University of Wisconsin-Madison.

  20. Evaluation of FOXFET biased ac-coupled silicon strip detector prototypes for CDF SVX upgrade

    SciTech Connect

    Laakso, M. Research Inst. for High Energy Physics , Helsinki )

    1992-03-01

    Silicon microstrip detectors for high-precision charged particle position measurements have been used in nuclear and particle physics for years. The detectors have evolved from simple surface barrier strip detectors with metal strips to highly complicated double-sided AC-coupled junction detectors. The feature of AC-coupling the readout electrodes from the diode strips necessitates the manufacture of a separate biasing structure for the strips, which comprises a common bias line together with a means for preventing the signal from one strip from spreading to its neighbors through the bias line. The obvious solution to this is to bias the strips through individual high value resistors. These resistors can be integrated on the detector wafer by depositing a layer of resistive polycrystalline silicon and patterning it to form the individual resistors. To circumvent the extra processing step required for polysilicon resistor processing and the rather difficult tuning of the process to obtain uniform and high enough resistance values throughout the large detector area, alternative methods for strip biasing have been devised. These include the usage of electron accumulation layer resistance for N{sup +}{minus} strips or the usage of the phenomenon known as the punch-through effect for P{sup +}{minus} strips. In this paper we present measurement results about the operation and radiation resistance of detectors with a punch-through effect based biasing structure known as a Field OXide Field-Effect Transistor (FOXFET), and present a model describing the FOXFET behavior. The studied detectors were prototypes for detectors to be used in the CDF silicon vertex detector upgrade.

  1. Study of the design optimization of AC-coupled single-sided silicon strip sensors

    NASA Astrophysics Data System (ADS)

    Jeon, H. B.; Kang, K. H.; Park, H.; Hyun, H. J.

    2015-05-01

    The high-intensity rare-isotope accelerator, RAON, will be constructed for nuclear physics research in Korea. AC-coupled single-sided silicon strip detectors (SSSDs) are being investigated for use in the Si-CsI detector of a large acceptance multi-purpose spectrometer to measure the energies of various isotopes. To determine the optimal design, four SSSD design parameters were examined in this study, namely the ratio of p+ implant width to strip pitch ( I/P), the width of the metal layer, the presence of an n+-edge field shaper (FS), and the distance between the guard-ring and sensor edge (DGS). The designed detectors were fabricated on high resistivity n-type silicon wafers of 500 μm thickness. The SSSDs had the strip pitch of 730 μm and 32 readout strips in each, and the size of the sensors was 40.0 × 25.5 mm2. In terms of the leakage current and production yield, the noise improved by up to 30%when the I/P ratio was 0.4, the metal layer was wider than the p+ implantation, and the DGS with n+-edge FS was twice the sensor thickness. The signal-to-noise ratio of the SSSD with the design parameters that provided the optimal leakage current and coupling capacitance was measured to be 29.1 using a 90Sr radioactive source and commercial electronics.

  2. Analytic formulation for the ac electrical conductivity in two-temperature, strongly coupled, overdense plasma: FORTRAN subroutine

    NASA Astrophysics Data System (ADS)

    Cauble, R.; Rozmus, W.

    1993-10-01

    A FORTRAN subroutine for the calculation of the ac electrical conductivity in two-temperature, strongly coupled, overdense plasma is presented. The routine is the result of a model calculation based on classical transport theory with application to plasmas created by the interaction of short pulse lasers and solids. The formulation is analytic and the routine is self-contained.

  3. The Design of Monolithic AC-coupled 1-Dimensional Voltage-Controlled-Oscillators (VCOs) Phased-array Network

    NASA Astrophysics Data System (ADS)

    Lie, Donald Y. C.; Lopez, J.

    2011-04-01

    A fully monolithic 1-Dimensional (1-D) AC-coupled Voltage-Controlled-Oscillators (VCOs) phased-array network design will be presented in this paper. This radio-frequency (RF) VCO array integrates on-chip inductors, varactors and bias current sources and it contains an odd number of VCOs AC-coupled through on-chip switchable resistor networks using MOSFETs. The measured results and SPICE simulated performance of the monolithic unit cell VCO agree reasonably well. Realistic circuit simulations in IBM 7HP 0.18 um BiCMOS design kit indicate promising results of the 1-D coupled-VCO array by showing the design can control the phasing of this on-chip VCO-array by means of tuning the edge elements and/or by varying the coupling strength via different resistor values using the on-chip MOSFET switches. Simulation data shows that it can offer high directivity and a possible element-to-element phase tuning arrangement that allows a ˜±20-30° degree coverage from broadside without the need for phase shifters or additional circuitry complexity. This AC-coupled 1-D VCO array, therefore, shows great potential for RF active antennas applications to perform wide angle beam steering for the highly used S-band.

  4. Identification of SEA coupling loss factors on a liquid rocket engine

    NASA Astrophysics Data System (ADS)

    Borello, G.; Alliot; Kernilis

    A test was performed on a full-scale model of the cryogenic engine of the VULCAIN in order to elucidate the power flow exchanges between the components and to quantify the losses at joints, and in effect to create a data base for coupling loss factors and damping loss factors. The relative damping loss factors of the different components are plotted. The most damped components are the oxygen turbopump and the hydrogen turbopump. The coupling loss factors of the oxygen turbopump with its connected components (nozzle, gas generator, and oxygen exhaust line) are shown.

  5. Technique for reduction of mechanical losses in AC superconducting coils due to thermal expansion properties of various FRP bobbins

    NASA Astrophysics Data System (ADS)

    Sekine, N.; Tada, S.; Higuchi, T.; Furumura, Y.; Takao, T.; Yamanaka, A.

    2005-10-01

    We reported about reduction of mechanical losses in AC superconducting coils. The method is the use of FRP bobbins fabricated with special fibers. Since their FRPs have negative thermal expansion coefficient to the fiber direction, the FRP bobbins expand to the circumferential direction during cooling down. In case of the superconducting coils with such FRP bobbins, the winding tensions do not decrease during cooling down. Therefore, the mechanical losses are reduced by the suppression of wire's vibration. Their special FRPs are a Dyneema® fiber reinforced plastic (DFRP), a Dyneema and glass fiber reinforced plastic (DGFRP), and a Zylon® fiber reinforced plastic (ZFRP). These materials have negative thermal expansion coefficient to the fiber direction, however, the amplitudes of thermal expansion are various by the quantity or quality of the fiber. In this paper, the values of thermal expansion were actually measured, and it was discussed about the influence on the mechanical losses. At the experimental results, the mechanical loss was small, so that the thermal strain to the circumferential direction on the coil was large. Moreover, in case of the coils with sufficiently strong winding tensions at coil-operating temperature, the mechanical losses vanished.

  6. Numerical analysis of ac loss in bifilar stacks and coils of ion beam assisted deposition YBCO coated conductors

    SciTech Connect

    Nguyen, Doan N.; Ashworth, Stephen P.; Willis, Jeffrey O.

    2009-03-15

    In this paper we present a finite element model using the commercial COMSOL software package for calculating the ac loss in bifilar stacks of high temperature superconducting tape. In the model, the current-voltage relationship characterizing the superconducting properties is assumed to follow a power law. The calculations were performed for infinite bifilar stacks with different values of layer-to-layer separation D. With appropriate settings for the boundary conditions, the numerical results agree well with the analytical data obtained from a recently proposed model [J. R. Clem, Phys. Rev. B 77, 134506 (2008)]. The numerical approach was also used to investigate the end effects in a bifilar stack to answer the following question: how many layers away from the end of a stack are required before the environment of a given layer is identical to that in an infinite stack? We find that the answer to this question depends strongly on the value of D. Based on this study, a model for calculating the ac loss in bifilar noninductively wound coils with a finite number of turns is proposed.

  7. Coupling loss factor of linear vibration energy harvesting systems in a framework of statistical energy analysis

    NASA Astrophysics Data System (ADS)

    Wang, Xu

    2016-02-01

    This paper establishes coupling loss factor of linear vibration energy harvesting systems in a framework of statistical energy analysis under parameter variations and random excitations. The new contributions of this paper are to define the numerical ranges of the dimensionless force factor for the weak, moderate and strong coupling and to study the connections of dimensionless force factor, coupling loss factor, coupling quotient, critical coupling strength, electro-mechanical coupling factor, damping loss factor and modal densities in linear vibration energy harvesting systems. The motivation of this paper is to enable statistical energy analysis of linear vibration energy harvesting systems for reliable performance predictions and design optimisation under parameter variations of materials and manufacturing processes and random ambient environmental excitations.

  8. Coupling an induction motor type generator to ac power lines. [making windmill generators compatible with public power lines

    NASA Technical Reports Server (NTRS)

    Nola, F. J. (Inventor)

    1984-01-01

    A system for coupling an induction motor type generator to an A.C. power line includes an electronic switch means that is controlled by a control system and is regulated to turn on at a relatively late point in each half cycle of its operation. The energizing power supplied by the line to the induction motor type generator is decreased and the net power delivered to the line is increased.

  9. AC loss characteristics of simulated CIC-type conductors having plastic conduit

    NASA Astrophysics Data System (ADS)

    Kojo, Y.; Sekine, N.; Tada, S.; Yamaguchi, Y.; Obama, J.; Takao, T.; Miyagi, D.; Yamanaka, A.

    2003-10-01

    When alternating current superconducting coils having cable-in-conduit conductors are fabricated, non-metallic conduit materials are necessary to avoid eddy current losses in the conduits. Using two kinds of non-metallic tapes made of glass fiber reinforced plastics (GFRPs) and Dyneema fiber reinforced plastics (DFRPs), we made the conductors with the GFRP conduits and DFRP conduits, and experimentally studied the total losses of the conductors. The measured results showed that the total loss of the conductor with the GFRP conduit was smaller than that with the DFRP conduit at the same value of the void ratio, the transport current, the external magnetic field, and so on. When the void ratios become high, the superconducting bundle cable can easily move in the conduit. Hence the measured total losses increased with the void ratios of the conductors.

  10. Interconception care for couples after perinatal loss: a comprehensive review of the literature.

    PubMed

    Moore, Tanya; Parrish, Heather; Black, Beth Perry

    2011-01-01

    Perinatal loss can be emotionally devastating for couples who experience miscarriage, fetal or neonatal death. Nurses in a variety of settings can assist couples through their grief by providing emotional support, giving information about the grief process, and in planning for a future pregnancy or deciding to forego future childbearing. This article explicates the relationship between grief and perinatal loss and its effects on couples, specifically in the interconception period, when the initial grief and distress have begun to subside. Interconception care focuses on bridging the couple from the end of the postpartum period to the subsequent pregnancy or decision not to conceive again. Nurses assist couples in distinguishing between uncomplicated grief, complicated grief, and depression, and make appropriate referrals. Openness to expressions of grief, helping couples mobilize support, considering readiness for another pregnancy, and directing couples to useful Internet sites are essential nursing interventions. PMID:21311269

  11. AC electrokinetic drug delivery in dentistry using an interdigitated electrode assembly powered by inductive coupling.

    PubMed

    Ivanoff, Chris S; Wu, Jie Jayne; Mirzajani, Hadi; Cheng, Cheng; Yuan, Quan; Kevorkyan, Stepan; Gaydarova, Radostina; Tomlekova, Desislava

    2016-10-01

    AC electrokinetics (ACEK) has been shown to deliver certain drugs into human teeth more effectively than diffusion. However, using electrical wires to power intraoral ACEK devices poses risks to patients. The study demonstrates a novel interdigitated electrode arrays (IDE) assembly powered by inductive coupling to induce ACEK effects at appropriate frequencies to motivate drugs wirelessly. A signal generator produces the modulating signal, which multiplies with the carrier signal to produce the amplitude modulated (AM) signal. The AM signal goes through the inductive link to appear on the secondary coil, then rectified and filtered to dispose of its carrier signal, and the positive half of the modulating signal appears on the load. After characterizing the device, the device is validated under light microscopy by motivating carboxylate-modified microspheres, tetracycline, acetaminophen, benzocaine, lidocaine and carbamide peroxide particles with induced ACEK effects. The assembly is finally tested in a common dental bleaching application. After applying 35 % carbamide peroxide to human teeth topically or with the IDE at 1200 Hz, 5 Vpp for 20 min, spectrophotometric analysis showed that compared to diffusion, the IDE enhanced whitening in specular optic and specular optic excluded modes by 215 % and 194 % respectively. Carbamide peroxide absorbance by the ACEK group was two times greater than diffusion as measured by colorimetric oxidation-reduction and UV-Vis spectroscopy at 550 nm. The device motivates drugs of variable molecular weight and structure wirelessly. Wireless transport of drugs to intraoral targets under ACEK effects may potentially improve the efficacy and safety of drug delivery in dentistry. PMID:27565821

  12. 3D analysis of eddy current loss in the permanent magnet coupling

    NASA Astrophysics Data System (ADS)

    Zhu, Zina; Meng, Zhuo

    2016-07-01

    This paper first presents a 3D analytical model for analyzing the radial air-gap magnetic field between the inner and outer magnetic rotors of the permanent magnet couplings by using the Amperian current model. Based on the air-gap field analysis, the eddy current loss in the isolation cover is predicted according to the Maxwell's equations. A 3D finite element analysis model is constructed to analyze the magnetic field spatial distributions and vector eddy currents, and then the simulation results obtained are analyzed and compared with the analytical method. Finally, the current losses of two types of practical magnet couplings are measured in the experiment to compare with the theoretical results. It is concluded that the 3D analytical method of eddy current loss in the magnet coupling is viable and could be used for the eddy current loss prediction of magnet couplings.

  13. 3D analysis of eddy current loss in the permanent magnet coupling.

    PubMed

    Zhu, Zina; Meng, Zhuo

    2016-07-01

    This paper first presents a 3D analytical model for analyzing the radial air-gap magnetic field between the inner and outer magnetic rotors of the permanent magnet couplings by using the Amperian current model. Based on the air-gap field analysis, the eddy current loss in the isolation cover is predicted according to the Maxwell's equations. A 3D finite element analysis model is constructed to analyze the magnetic field spatial distributions and vector eddy currents, and then the simulation results obtained are analyzed and compared with the analytical method. Finally, the current losses of two types of practical magnet couplings are measured in the experiment to compare with the theoretical results. It is concluded that the 3D analytical method of eddy current loss in the magnet coupling is viable and could be used for the eddy current loss prediction of magnet couplings. PMID:27475575

  14. Corrosion loss measurement of boiler tubes in a waste incineration environment by A.C. impedance method

    SciTech Connect

    Matsunaga, Yasuo; Nakagawa, Kiyokazu

    1997-08-01

    To monitor the corrosion rate of materials of boiler tubes in simulated waste incineration environment, A.C. impedance measurements were carried out for Alloy 625, SUS347H and STBA24 embedded in NaCl- KCl- NaSO{sub 4}-K{sub 2}SO{sub 4}-Al{sub 2}O{sub 3} mixed synthetic ash deposit at 600 C. Though the ash includes some non-melting component, A.C. impedance measurements can be applied to evaluate corrosion rates in the same manner the corrosion of materials immersed in molten salts. Supposing the difference of impedance between the low frequency and high frequency ({Delta}R) as polarization resistance, a linear relation was obtained between 1/{Delta}R and corrosion losses in air, air-0.1 vol.% HCl and air-10vol.% H{sub 2}O atmospheres. The HCl addition in accelerated the corrosion of all specimens by reducing basicity of the molten salt. On the other hand, the H{sub 2}O addition reduced the corrosion of Alloy 625, but it accelerated the corrosion of SUS347H and STBA24.

  15. Dimensions of Ambiguous Loss in Couples Coping with Mild Cognitive Impairment

    ERIC Educational Resources Information Center

    Blieszner, Rosemary; Roberto, Karen A.; Wilcox, Karen L.; Barham, Elizabeth J.; Winston, Brianne L.

    2007-01-01

    We applied the theory of ambiguous loss to couples with mild cognitive impairment (MCI), an age-related decline in memory and other cognitive processes assumed not to interfere with daily activities or the maintenance of personal relationships. Face-to-face interviews with 67 older married couples revealed that lack of understanding about the…

  16. AC losses in BiPbSrCaCuO-2223/Ag multifilamentary tapes in conditions similar to those in superconducting transmission lines

    NASA Astrophysics Data System (ADS)

    Majoros, M.; Glowacki, B. A.; Campbell, A. M.; Han, Z.; Vase, P.

    1998-12-01

    Transport AC losses in BiPbSrCaCuO-2223/Ag multifilamentary tape with 19 filaments were measured. The sample was 1.05 m long, wound in form of a helix with a gap between the tapes comparable with the tape width. Two different types of potential leads-tape following, axis following-with taps positioned in the centre of the tape were mounted on inner as well as outer surface of the helical sample. AC losses were measured at power frequencies by an electrical method using a lock-in nanovoltmeter. The influence of potential wires arrangement and the potential taps position on measured AC loss level and its frequency dependence was analysed.

  17. An improved FEM model for computing transport AC loss in coils made of RABiTS YBCO coated conductors for electric machines

    NASA Astrophysics Data System (ADS)

    Ainslie, Mark D.; Rodriguez-Zermeno, Victor M.; Hong, Zhiyong; Yuan, Weijia; Flack, Timothy J.; Coombs, Timothy A.

    2011-04-01

    AC loss can be a significant problem for any applications that utilize or produce an AC current or magnetic field, such as an electric machine. The authors investigate the electromagnetic properties of high temperature superconductors with a particular focus on the AC loss in superconducting coils made from YBCO coated conductors for use in an all-superconducting electric machine. This paper presents an improved 2D finite element model for the cross-section of such coils, based on the H formulation. The model is used to calculate the transport AC loss of a racetrack-shaped coil using constant and magnetic field-dependent critical current densities, and the inclusion and exclusion of a magnetic substrate, as found in RABiTS (rolling-assisted biaxially textured substrate) YBCO coated conductors. The coil model is based on the superconducting stator coils used in the University of Cambridge EPEC Superconductivity Group's all-superconducting permanent magnet synchronous motor design. To validate the modeling results, the transport AC loss of a stator coil is measured using an electrical method based on inductive compensation by means of a variable mutual inductance. Finally, the implications of the findings on the performance of the motor are discussed.

  18. Coupling losses of fusion conductors: Influence of some design parameters

    SciTech Connect

    Duchateau, J.L.; Ciazynski, D.; Martinez, A.

    1996-12-31

    Superconductors for fusion are subjected to fast variations of magnetic fields. The effective diameter of the strands is of great importance to limit the level of losses appearing during theses variations. Another less controlled characteristic also plays a major role: the conductor time constant. A model is given to calculate this time constant. The void fraction, the twist pitches associated to the different stages, the chromium coating and the internal resistive barriers inside the strand influence greatly this time constant. The influence of the different parameters is discussed through practical considerations depending on the kind of cable considered. This model is applied to measurements performed at the University of Twente and at CEA on Nb{sub 3}Sn subcables made of twisted strands relevant for ITER. The application of this model is also discussed for a typical NbTi strand for fusion application developed by GEC AISA. As a matter of fact, the NbTi is again present in the ITER design for most of the poloidal field coils, which represents hundreds tons of material.

  19. Job loss and depressive symptoms in couples: common stressors, stress transmission, or relationship disruption?

    PubMed

    Howe, George W; Levy, Mindy Lockshin; Caplan, Robert D

    2004-12-01

    Three models of the linkage between stressors and depressive symptoms were tested in 252 couples after job loss. Data were analyzed to test whether depressive symptoms in both members of the couple were due to common stressors, the transmission of stress from 1 member to the other, or changes in relationship quality. Evidence was found for all 3 processes. Common stressors influenced depressive symptoms in both partners. Anger and depressive symptoms of each partner partially mediated these effects on the other partner, as did reductions in relationship quality. Findings suggest that interventions to help couples cope with the aftermath of job loss may hold promise for preventing depressive reactions to stress. PMID:15598169

  20. Weighty dynamics: exploring couples' perceptions of post-weight-loss interaction.

    PubMed

    Romo, Lynsey Kluever; Dailey, René M

    2014-01-01

    Although romantic couples can use communication to help one another lose weight and maintain weight loss, the effect of weight loss on partner interaction is less understood. However, an examination of the interpersonal context in which partners manage their weight is important to help partners negotiate their weight, their relationship, and the U.S. obesity epidemic. Guided by systems theory, this study explored partners' perceptions of post-weight-loss interaction in relationships in which one partner lost weight and the other did not. Through qualitative questionnaires of 42 adults (21 romantic couples), the dyadic investigation revealed that while losing weight resulted in positive interaction for many partners (e.g., engaging in a shared healthy lifestyle), shedding weight also yielded some negative consequences (e.g., non-weight-loss partner criticism). The extent to which partners embraced new weight management rules and patterns largely influenced post-weight-loss communication and behavior. PMID:24156394

  1. Microwave Absorption and Low-Frequency AC Losses in 1-2-3 Cuprate Superconductors

    NASA Astrophysics Data System (ADS)

    Huang, Ming Xun

    We have studied various aspects of microwave absorption in cuprates of the prototype REBa_2Cu _3O_{rm x} (6 < x < 7), where RE stands for Y or a rare earth ion. The first series of experiments concern the discovery and subsequent elucidation of a huge increase in zero field microwave absorption, at temperatures below 20 K, in micron size powder samples of ErBa_2Cu _3O_{rm x}. The field dependence of the microwave absorption was used to show that this abnormal zero field signal is a part of a broad and highly distorted electron spin resonance (ESR) spectrum. Spectra at different frequencies were analyzed using the "weak exchange, strong dipole field" Kubo-Toyabe model for the first time and we conclude that there is a large (~1 kOe) fluctuating local dipolar field at the Er site coming from the other Er^{3+} magnetic moments. For better understanding, experiments were done on ESR in powders of Er_{rm x}Y _{rm 1-z}Ba_2 Cu_3O_6 (0.02 < z < 1). For z < 0.4, another partially resolved line appeared at low fields. These spectra cannot be described as a powder pattern due to a single line with an anisotropic g-value. Rather they appear to be the sum of two Kubo -Toyabe lines. Most likely these lines are resonances coming from two closely spaced (~1K) low lying doublets. Crystal field calculations indicate that the distortion away from cubic symmetry implied by our results is much smaller than that required to describe the results of neutron scattering measurements. Another series of experiments were done to measure the increase in the microwave absorption in thin films of YBa_2Cu_3O _7 due to the application of a dc magnetic field (B) between 0.45 and 1.4 Tesla at 0.8 < (T/Tc) < 1. The data are very well represented by conventional models of fluxon dynamics. We have also measured the real (chi _1) and imaginary (chi_2 ) parts of the low frequency (<150 Hz) complex ac susceptibility. It was found that the data can be understood by using the Bean model.

  2. Applying a fuzzy-set-based method for robust estimation of coupling loss factors

    NASA Astrophysics Data System (ADS)

    Nunes, R. F.; Ahmida, K. M.; Arruda, J. R. F.

    2007-10-01

    Finite element models have been used by many authors to provide accurate estimations of coupling loss factors. Although much progress has been achieved in this area, little attention has been paid to the influence of uncertain parameters in the finite element model used to estimate these factors. It is well known that, in the mid-frequency range, uncertainty is a major issue. In this context, a spectral element method combined with a special implementation of a fuzzy-set-based method, which is called the transformation method, is proposed as an alternative to compute coupling loss factors. The proposed technique is applied to a frame-type junction, which can consist of two beams connected at an arbitrary angle. In this context, two problems are investigated. In the first one, the influence of the confidence intervals of the coupling loss factors on the estimated energy envelopes assuming a unit power input is considered. In the other problem the influence of the envelope of the input power obtained considering the confidence intervals of the coupling loss factors is also taken into account. The estimates of the intervals are obtained by using the spectral element method combined with a fuzzy-set-based method. Results using a Monte Carlo analysis for the estimation of the coupling loss factors under the influence of uncertain parameters are shown for comparison and verification of the fuzzy method.

  3. Does ocean coupling matter for the northern extratropical response to projected Arctic sea ice loss?

    NASA Astrophysics Data System (ADS)

    Deser, Clara; Sun, Lantao; Tomas, Robert A.; Screen, James

    2016-03-01

    The question of whether ocean coupling matters for the extratropical Northern Hemisphere atmospheric response to projected late 21st century Arctic sea ice loss is addressed using a series of experiments with Community Climate System Model version 4 at 1° spatial resolution under different configurations of the ocean model component: no interactive ocean, thermodynamic slab ocean, and full-depth (dynamic plus thermodynamic) ocean. Ocean-atmosphere coupling magnifies the response to Arctic sea ice loss but does not change its overall structure; however, a slab ocean is inadequate for inferring the role of oceanic feedbacks. The westerly winds along the poleward flank of the eddy-driven jet weaken in response to Arctic sea ice loss, accompanied by a smaller-magnitude strengthening on the equatorward side, with largest amplitudes in winter. Dynamical and thermodynamic oceanic feedbacks amplify this response by approximately 50%. Air temperature, precipitation, and sea level pressure responses also show sensitivity to the degree of ocean coupling.

  4. Loss function used in optimization of array of coupled tracking radioelectronic systems

    NASA Astrophysics Data System (ADS)

    Vagapov, V. B.

    1984-05-01

    A loss function is defined as a criterion for optimization of coupled multidimensional tracking systems, in preference to the two conventional complementary loss functions relative to the maximum tracking accuracy and the permissible range of tracking error respectively. The penalty of error is calculated accordingly by solution of the corresponding equation of motion for the tracking system, specifically a second-order (velocity-acceleration) tracking system in which the discriminator output signal is an additive mixture of tracking error and interference. First, such a one dimensional tracking system is considered and next, a two dimensional system consisting of two such one dimensional ones coupled through the error of their identical respective tracking loops. The mathematical expectation of this loss function was calculated as a function of the slope of the discriminator characteristic, the curves for n = 2,4,8 were normalized to minimum values of the corresponding loss function.

  5. Polymer waveguide end facet roughness and optical input/output coupling loss for OPCB applications

    NASA Astrophysics Data System (ADS)

    Baghsiahi, Hadi; Wang, Kai; Pitwon, Richard; Selviah, David R.

    2014-03-01

    Electro-optical printed circuit board technology (EOCB) based on integrated planar polymer optical waveguides has been the subject of research and development for many years to provide a cost viable, fully integrated system embedded optical interconnect solution, however a number of constraints of this technology have yet to be overcome. Optical coupling loss at the input and output of the waveguides is one of the major issues and waveguide end facet roughness is one of the main sources of the coupling loss which is investigated in this paper. The results of a comprehensive investigation of the end facet roughness of multimode polymer waveguides, fabricated on FR4 printed circuit boards, PCBs, and its effect of optical loss are presented theoretically and experimentally. The waveguide end facet roughness was measured using an atomic force microscope, AFM, when the waveguides were cut using a milling router with various numbers of cutting edges called flutes. The optimized cutting parameters are derived and the optical coupling loss, between the laser source and the waveguide, due to the different roughness magnitudes is measured by experiment for the first time. To improve the surface quality and decrease the waveguide optical loss, a new fabrication technique for reducing the end facet roughness after cutting is proposed and demonstrated. The insertion loss was reduced by 2.60 dB +/- 1.3 dB which is more than that achieved by other conventional methods such as index matching fluid.

  6. Superconducting-magnetic heterostructures: a method of decreasing AC losses and improving critical current density in multifilamentary conductors.

    PubMed

    Glowacki, B A; Majoros, M

    2009-06-24

    Magnetic materials can help to improve the performance of practical superconductors on the macroscale/microscale as magnetic diverters and also on the nanoscale as effective pinning centres. It has been established by numerical modelling that magnetic shielding of the filaments reduces AC losses in self-field conditions due to decoupling of the filaments and, at the same time, it increases the critical current of the composite. This effect is especially beneficial for coated conductors, in which the anisotropic properties of the superconductor are amplified by the conductor architecture. However, ferromagnetic coatings are often chemically incompatible with YBa(2)Cu(3)O(7) and (Pb,Bi)(2)Sr(2)Ca(2)Cu(3)O(9) conductors, and buffer layers have to be used. In contrast, in MgB(2) conductors an iron matrix may remain in direct contact with the superconducting core. The application of superconducting-magnetic heterostructures requires consideration of the thermal and electromagnetic stability of the superconducting materials used. On one hand, magnetic materials reduce the critical current gradient across the individual filaments but, on the other hand, they often reduce the thermal conductivity between the superconducting core and the cryogen, which may cause destruction of the conductor in the event of thermal instability. A possible nanoscale method of improving the critical current density of superconducting conductors is the introduction of sub-micron magnetic pinning centres. However, the volumetric density and chemical compatibility of magnetic inclusions has to be controlled to avoid suppression of the superconducting properties. PMID:21828430

  7. Proposal of new structure of MgB 2 wires with low AC loss for stator windings of fully superconducting motors located in iron core slots

    NASA Astrophysics Data System (ADS)

    Kajikawa, K.; Osaka, R.; Kuga, H.; Nakamura, T.; Wakuda, T.

    2011-11-01

    The new structure of MgB 2 monofilamentary wires for stator windings of fully superconducting motors is proposed to reduce their AC losses in iron core slots for the application of an alternating transport current. In order to validate the proposed structure of wire for loss reduction, numerical calculations are carried out by means of a finite element method using edge elements formulated with a self-field due to currents induced in an analysis region. It is assumed that the voltage-current characteristics of the MgB 2 superconductor are given by Bean’s critical state model, in which the critical current density is independent of the local magnetic field. The influences of wire structures on the AC losses are discussed quantitatively toward the optimum design of stator windings in fully superconducting motors with the MgB 2 wires.

  8. Structured Coupling of Probability Loss Distributions: Assessing Joint Flood Risk in Multiple River Basins.

    PubMed

    Timonina, Anna; Hochrainer-Stigler, Stefan; Pflug, Georg; Jongman, Brenden; Rojas, Rodrigo

    2015-11-01

    Losses due to natural hazard events can be extraordinarily high and difficult to cope with. Therefore, there is considerable interest to estimate the potential impact of current and future extreme events at all scales in as much detail as possible. As hazards typically spread over wider areas, risk assessment must take into account interrelations between regions. Neglecting such interdependencies can lead to a severe underestimation of potential losses, especially for extreme events. This underestimation of extreme risk can lead to the failure of riskmanagement strategies when they are most needed, namely, in times of unprecedented events. In this article, we suggest a methodology to incorporate such interdependencies in risk via the use of copulas. We demonstrate that by coupling losses, dependencies can be incorporated in risk analysis, avoiding the underestimation of risk. Based on maximum discharge data of river basins and stream networks, we present and discuss different ways to couple loss distributions of basins while explicitly incorporating tail dependencies. We distinguish between coupling methods that require river structure data for the analysis and those that do not. For the later approach we propose a minimax algorithm to choose coupled basin pairs so that the underestimation of risk is avoided and the use of river structure data is not needed. The proposed methodology is especially useful for large-scale analysis and we motivate and apply our method using the case of Romania. The approach can be easily extended to other countries and natural hazards. PMID:26010101

  9. Amplitude loss of sonic waveform due to source coupling to the medium

    USGS Publications Warehouse

    Lee, Myung W.; Waite, William F.

    2007-01-01

    In contrast to hydrate-free sediments, sonic waveforms acquired in gas hydrate-bearing sediments indicate strong amplitude attenuation associated with a sonic velocity increase. The amplitude attenuation increase has been used to quantify pore-space hydrate content by attributing observed attenuation to the hydrate-bearing sediment's intrinsic attenuation. A second attenuation mechanism must be considered, however. Theoretically, energy radiation from sources inside fluid-filled boreholes strongly depends on the elastic parameters of materials surrounding the borehole. It is therefore plausible to interpret amplitude loss in terms of source coupling to the surrounding medium as well as to intrinsic attenuation. Analyses of sonic waveforms from the Mallik 5L-38 well, Northwest Territories, Canada, indicate a significant component of sonic waveform amplitude loss is due to source coupling. Accordingly, all sonic waveform amplitude analyses should include the effect of source coupling to accurately characterize a formation's intrinsic attenuation.

  10. Is amplitude loss of sonic waveforms due to intrinsic attenuation or source coupling to the medium?

    USGS Publications Warehouse

    Lee, Myung W.

    2006-01-01

    Sonic waveforms acquired in gas-hydrate-bearing sediments indicate strong amplitude loss associated with an increase in sonic velocity. Because the gas hydrate increases sonic velocities, the amplitude loss has been interpreted as due to intrinsic attenuation caused by the gas hydrate in the pore space, which apparently contradicts conventional wave propagation theory. For a sonic source in a fluid-filled borehole, the signal amplitude transmitted into the formation depends on the physical properties of the formation, including any pore contents, in the immediate vicinity of the source. A signal in acoustically fast material, such as gas-hydrate-bearing sediments, has a smaller amplitude than a signal in acoustically slower material. Therefore, it is reasonable to interpret the amplitude loss in the gas-hydrate-bearing sediments in terms of source coupling to the surrounding medium as well as intrinsic attenuation. An analysis of sonic waveforms measured at the Mallik 5L-38 well, Northwest Territories, Canada, indicates that a significant part of the sonic waveform's amplitude loss is due to a source-coupling effect. All amplitude analyses of sonic waveforms should include the effect of source coupling in order to accurately characterize the formation's intrinsic attenuation.

  11. A coupled effect of nuclear and electronic energy loss on ion irradiation damage in lithium niobate

    DOE PAGESBeta

    Liu, Peng; Zhang, Yanwen; Xue, Haizhou; Jin, Ke; Crespillo, Miguel L.; Wang, Xuelin; Weber, William J.

    2016-01-09

    Understanding irradiation effects induced by elastic energy loss to atomic nuclei and inelastic energy loss to electrons in a crystal, as well as the coupled effect between them, is a scientific challenge. Damage evolution in LiNbO3 irradiated by 0.9 and 21 MeV Si ions at 300 K has been studied utilizing Rutherford backscattering spectrometry in channeling mode. During the low-energy ion irradiation process, damage accumulation produced due to elastic collisions is described utilizing a disorder accumulation model. Moreover, low electronic energy loss is shown to induce observable damage that increases with ion fluence. For the same electronic energy loss, themore » velocity of the incident ion could affect the energy and spatial distribution of excited electrons, and therefore effectively modify the diameter of the ion track. Furthermore, nonlinear additive phenomenon of irradiation damage induced by high electronic energy loss in pre-damaged LiNbO3 has been observed. The result indicates that pre-existing damage induced from nuclear energy loss interacts synergistically with inelastic electronic energy loss to promote the formation of amorphous tracks and lead to rapid phase transformation, much more efficient than what is observed in pristine crystal solely induced by electronic energy loss. As a result, this synergistic effect is attributed to the fundamental mechanism that the defects produced by the elastic collisions result in a decrease in thermal conductivity, increase in the electron-phonon coupling, and further lead to higher intensity in thermal spike from intense electronic energy deposition along high-energy ion trajectory.« less

  12. Development of a cryogenic GaAs AC-coupled CTIA readout for far-infrared and submillimeter detectors

    NASA Astrophysics Data System (ADS)

    Nagata, Hirohisa; Kobayashi, Jun; Matsuo, Hiroshi; Hibi, Yasunori; Nakahashi, Misato; Ikeda, Hirokazu; Fujiwara, Mikio

    2008-07-01

    We have been developing cryogenic readout integrated circuits (ROICs) for sensitive detectors at far-infrared and submillimeter wavelengths: The ROICs are constructed from SONY GaAs-JFETs, which have excellent performance even at less than 1 K. In addition, it is suitable device for ultra low background applications because of the extremely low gate leakage current. In the spring of 2008, we have designed and fabricated 4-ch AC-coupled capacitive transimpedance amplifiers and several basic digital circuits giving multiplex function for 32-element SIS photon detector array. The expected performance of the amplifier is as follows; open loop gain of >2000, power consumption <1.5 μW, and input referred noise ~ 1 μV/√Hz@1Hz. A summary of this 2008's experimental production and initial test results are presented in this paper.

  13. Emotion-induced loss aversion and striatal-amygdala coupling in low-anxious individuals

    PubMed Central

    Charpentier, Caroline J.; Martino, Benedetto De; Sim, Alena L.; Sharot, Tali; Roiser, Jonathan P.

    2016-01-01

    Adapting behavior to changes in the environment is a crucial ability for survival but such adaptation varies widely across individuals. Here, we asked how humans alter their economic decision-making in response to emotional cues, and whether this is related to trait anxiety. Developing an emotional decision-making task for functional magnetic resonance imaging, in which gambling decisions were preceded by emotional and non-emotional primes, we assessed emotional influences on loss aversion, the tendency to overweigh potential monetary losses relative to gains. Our behavioral results revealed that only low-anxious individuals exhibited increased loss aversion under emotional conditions. This emotional modulation of decision-making was accompanied by a corresponding emotion-elicited increase in amygdala-striatal functional connectivity, which correlated with the behavioral effect across participants. Consistent with prior reports of ‘neural loss aversion’, both amygdala and ventral striatum tracked losses more strongly than gains, and amygdala loss aversion signals were exaggerated by emotion, suggesting a potential role for this structure in integrating value and emotion cues. Increased loss aversion and striatal-amygdala coupling induced by emotional cues may reflect the engagement of adaptive harm-avoidance mechanisms in low-anxious individuals, possibly promoting resilience to psychopathology. PMID:26589451

  14. Tunable negligible-loss energy transfer between dipolar-coupled magnetic disks by stimulated vortex gyration

    PubMed Central

    Jung, Hyunsung; Lee, Ki-Suk; Jeong, Dae-Eun; Choi, Youn-Seok; Yu, Young-Sang; Han, Dong-Soo; Vogel, Andreas; Bocklage, Lars; Meier, Guido; Im, Mi-Young; Fischer, Peter; Kim, Sang-Koog

    2011-01-01

    A wide variety of coupled harmonic oscillators exist in nature. Coupling between different oscillators allows for the possibility of mutual energy transfer between them and the information-signal propagation. Low-energy input signals and their transport with negligible energy loss are the key technological factors in the design of information-signal processing devices. Here, utilizing the concept of coupled oscillators, we experimentally demonstrated a robust new mechanism for energy transfer between spatially separated dipolar-coupled magnetic disks - stimulated vortex gyration. Direct experimental evidence was obtained by a state-of-the-art experimental time-resolved soft X-ray microscopy probe. The rate of energy transfer from one disk to the other was deduced from the two normal modes' frequency splitting caused by dipolar interaction. This mechanism provides the advantages of tunable energy transfer rates, low-power input signals and negligible energy loss in the case of negligible intrinsic damping. Coupled vortex-state disks might be implemented in applications for information-signal processing. PMID:22355578

  15. Effect of plasmonic losses on light emission enhancement in quantum-wells coupled to metallic gratings

    SciTech Connect

    Sadi, Toufik; Oksanen, Jani; Tulkki, Jukka

    2013-12-14

    Recent experimental work has shown significant luminescence enhancement from near-surface quantum-well (QW) structures using metallic grating to convert surface plasmon (SP) modes into radiative modes. This work introduces a detailed theoretical study of plasmonic losses and the role of SPs in improving light extraction from grated light-emitting QW structures, using the fluctuational electrodynamics method. The method explains experimental results demonstrating emission enhancement, light scattering, and plasmonic coupling in the structures. We study these effects in angle-resolved reflectometry and luminescence setups in InGaN QW structures with silver grating. In contrast to experiments, our model allows direct calculation of the optical losses. The model predicts that the plasmonic coupling and scattering increases light emission by a factor of up to three compared to a flat semiconductor structure. This corresponds to reducing the absorption losses from approximately 93% in the ungrated metallic structure to 75% in the grated structure. Lower losses are associated with a significant emission enhancement enabled by the SPs of silver/GaN interfaces, which are present in the blue/green wavelength range, and can be optimized by carefully nanostructuring the metal layer and by the positioning of the QW. In general, the enhancement results from the interplay of mode scattering, conversion of SP energy directly into light, and losses in the metallic grating. The reported losses are very high when compared to the losses present in modern light-emitting diodes (LEDs). Albeit, our work provides tools needed for further optimization of plasmonic light extraction, eventually leading to highly efficient LEDs.

  16. Nonlinear coupled-mode theory for periodic plasmonic waveguides and metamaterials with loss and gain.

    PubMed

    Sukhorukov, Andrey A; Solntsev, Alexander S; Kruk, Sergey S; Neshev, Dragomir N; Kivshar, Yuri S

    2014-02-01

    We derive general coupled-mode equations describing the nonlinear interaction of electromagnetic modes in periodic media with loss and gain. Our approach is rigorously based on the Lorentz reciprocity theorem, and it can be applied to a broad range of metal-dielectric photonic structures, including plasmonic waveguides and metamaterials. We verify that our general results agree with the previous analysis of particular cases, and predict novel effects on self- and cross-phase modulation in multilayer nonlinear fishnet metamaterials. PMID:24487840

  17. Apparent ac losses in helical BiPbSrCaCuO-2223/Ag multifilamentary tape measured by different potential taps at power frequencies

    NASA Astrophysics Data System (ADS)

    Majoros, M.; Glowacki, B. A.; Campbell, A. M.; Han, Z.; Vase, P.

    1999-03-01

    Transport ac losses in BiPbSrCaCuO-2223/Ag multifilamentary tape in form of a helix with a 3 mm gap between the turns were measured in frequency range 40-125 Hz. Different positions of potential taps on outer and inner surface of the tape were used. Potential wires were led along the tape axis as well as along the axis of the helix. At currents lower than the critical current a strong dependence of measured apparent ac losses on potential taps position and on the form of potential wires was found. Suitably wound contact-less pick-up coils to detect magnetic flux of different magnetic field components were also used. They allowed us to measure the `magnetisation' part of apparent losses even when the sample was in resistive state, as well as the losses at the gap of the tape. Comparison of the losses at the gap of the tape with the existing theoretical model was made.

  18. Reprint of: First experience with the new Coupling Loss Induced Quench system

    NASA Astrophysics Data System (ADS)

    Ravaioli, E.; Datskov, V. I.; Dudarev, A. V.; Kirby, G.; Sperin, K. A.; ten Kate, H. H. J.; Verweij, A. P.

    2014-09-01

    New-generation high-field superconducting magnets pose a challenge relating to the protection of the coil winding pack in the case of a quench. The high stored energy per unit volume calls for a very efficient quench detection and fast quench propagation in order to avoid damage due to overheating. A new protection system called Coupling-Loss Induced Quench (CLIQ) was recently developed and tested at CERN. This method provokes a fast change in the magnet transport current by means of a capacitive discharge. The resulting change in the local magnetic field induces inter-filament and inter-strand coupling losses which heat up the superconductor and eventually initiate a quench in a large fraction of the coil winding pack. The method is extensively tested on a Nb-Ti single-wire test solenoid magnet in the CERN Cryogenic Laboratory in order to assess its performance, optimize its operating parameters, and study new electrical configurations. Each parameter is thoroughly analyzed and its impact on the quench efficiency highlighted. Furthermore, an alternative method is also considered, based on a CLIQ discharge through a resistive coil magnetically coupled with the solenoid but external to it. Due to the strong coupling between the external coil and the magnet, the oscillating current in the external coil changes the magnetic field in the solenoid strands and thus generates coupling losses in the strands. Although for a given charging voltage this configuration usually yields poorer quench performance than a standard CLIQ discharge, it has the advantage of being electrically insulated from the solenoid coil, and thus it can work with much higher voltage.

  19. Glass Solder Approach for Robust, Low-Loss, Fiber-to-Waveguide Coupling

    NASA Technical Reports Server (NTRS)

    McNeil, Shirley; Battle, Philip; Hawthorne, Todd; Lower, John; Wiley, Robert; Clark, Brett

    2012-01-01

    The key advantages of this approach include the fact that the index of interface glass (such as Pb glass n = 1.66) greatly reduces Fresnel losses at the fiber-to-waveguide interface, resulting in lower optical losses. A contiguous structure cannot be misaligned and readily lends itself for use on aircraft or space operation. The epoxy-free, fiber-to-waveguide interface provides an optically pure, sealed interface for low-loss, highpower coupling. Proof of concept of this approach has included successful attachment of the low-melting-temperature glass to the x-y plane of the crystal, successful attachment of the low-meltingtemperature glass to the end face of a standard SMF (single-mode fiber), and successful attachment of a wetted lowmelting- temperature glass SMF to the end face of a KTP crystal. There are many photonic components on the market whose performance and robustness could benefit from this coupling approach once fully developed. It can be used in a variety of fibercoupled waveguide-based components, such as frequency conversion modules, and amplitude and phase modulators. A robust, epoxy-free, contiguous optical interface lends itself to components that require low-loss, high-optical-power handling capability, and good performance in adverse environments such as flight or space operation.

  20. Visualizing plasmon coupling in closely spaced chains of Ag nanoparticles by electron energy-loss spectroscopy.

    PubMed

    Song, Fengqi; Wang, Tingyu; Wang, Xuefeng; Xu, Changhui; He, Longbing; Wan, Jianguo; Van Haesendonck, Christian; Ringer, Simon P; Han, Min; Liu, Zongwen; Wang, Guanghou

    2010-02-01

    Anisotropic plasmon coupling in closely spaced chains of Ag nanoparticles is visualized using electron energy-loss spectroscopy in a scanning transmission electron microscope. For dimers as the simplest chain, mapping the plasmon excitations with nanometer spatial resolution and an energy resolution of 0.27 eV intuitively identifies two coupling plasmons. The in-phase mode redshifts from the ultraviolet region as the interparticle spacing is reduced, reaching the visible range at 2.7 eV. Calculations based on the discrete-dipole approximation confirm its optical activeness, where the longitudinal direction is constructed as the path for light transportation. Two coupling paths are then observed in an inflexed four-particle chain. PMID:20077517

  1. Generation of entangled macroscopic light fields with a coupled gain-loss waveguide

    NASA Astrophysics Data System (ADS)

    Vashahri-Ghamsari, Saeid; He, Bing; Xiao, Min

    2016-05-01

    We explore a Parity-Time (PT)-symmetric optical system of two coupled single-mode waveguides. One of the waveguides contains a gain medium, while the second one is with a loss medium. The magnitude of the gain can be adjusted to be equal to that of the loss, so that the PT-symmetric condition will be achieved. Moreover, we add a squeezing element to one of the waveguides. The squeezing can be generated in a parametric down conversion process. Moreover, we have included both amplifying and decaying noises in the process. It is shown that the squeezing intensifies the noise-induced photon emission and leads to the entanglement of the output light fields. Under certain conditions, the noises tend to eliminate the entanglement. If the input beam is strong, the entanglement due to the squeezing can become strong enough to overcome the noise effects, resulting in macroscopic entangled output fields.

  2. Effect of the electron energy distribution on total energy loss with argon in inductively coupled plasmas

    SciTech Connect

    Kim, June Young; Kim, Young-Cheol; Kim, Yu-Sin; Chung, Chin-Wook

    2015-01-15

    The total energy lost per electron-ion pair lost ε{sub T} is investigated with the electron energy distribution function (EEDF). The EEDFs are measured at various argon powers in RF inductively coupled plasma, and the EEDFs show a depleted distribution (a discontinuity occurring at the minimum argon excitation threshold energy level) with the bulk temperature and the tail temperature. The total energy loss per electron-ion pair lost ε{sub T} is calculated from a power balance model with the Maxwellian EEDFs and the depleted EEDFs and then compared with the measured ε{sub T} from the floating probe. It is concluded that the small population of the depleted high energy electrons dramatically increases the collisional energy loss, and the calculated ε{sub T} from the depleted EEDFs has a value that is similar to the measured ε{sub T}.

  3. Effect of the electron energy distribution on total energy loss with argon in inductively coupled plasmas

    NASA Astrophysics Data System (ADS)

    Kim, June Young; Kim, Young-Cheol; Kim, Yu-Sin; Chung, Chin-Wook

    2015-01-01

    The total energy lost per electron-ion pair lost ɛT is investigated with the electron energy distribution function (EEDF). The EEDFs are measured at various argon powers in RF inductively coupled plasma, and the EEDFs show a depleted distribution (a discontinuity occurring at the minimum argon excitation threshold energy level) with the bulk temperature and the tail temperature. The total energy loss per electron-ion pair lost ɛT is calculated from a power balance model with the Maxwellian EEDFs and the depleted EEDFs and then compared with the measured ɛT from the floating probe. It is concluded that the small population of the depleted high energy electrons dramatically increases the collisional energy loss, and the calculated ɛT from the depleted EEDFs has a value that is similar to the measured ɛT.

  4. Women's voices after pregnancy loss: couples' patterns of communication and support.

    PubMed

    Black, R B

    1991-01-01

    This paper reports results of a study of prenatal diagnosis patients who lost pregnancies. The women felt they shared much in common with their male partners and generally felt understood and supported by the men. However, many of the women also saw their responses to the loss as different from those of their male partners. A variety of coping patterns were adopted by the women in the face of these differences. Implications are considered for preventive efforts to minimize distress; treatment approaches to help couples who experience greater difficulties; and future research directions. PMID:1808722

  5. Energy Loss of Heavy Quarks in a QGP with a Running Coupling Constant Approach

    NASA Astrophysics Data System (ADS)

    Gossiaux, P. B.; Aichelin, J.

    2009-11-01

    We show that the effective running coupling constant, α, and the effective regulator, κm˜D2, which we used recently to calculate the energy loss, dEdx, and the elliptic flow, v, of heavy quarks in an expanding quark gluon plasma plasma (QGP) [P. B. Gossiaux and J. Aichelin, Phys. Rev. C78, 014904 (2008), [arXiv:0802.2525], P. B. Gossiaux and J. Aichelin, J. Phys. G36 (2009) 064028, [arXiv:0901.2462], P. B. Gossiaux, R. Bierkandt and J. Aichelin, Phys. Rev. C79 (2009) 044906 [arXiv:0901.0946

  6. Comparison of AC losses, magnetic field/current distributions and critical currents of superconducting circular pancake coils and infinitely long stacks using coated conductors

    NASA Astrophysics Data System (ADS)

    Yuan, Weijia; Campbell, A. M.; Hong, Z.; Ainslie, M. D.; Coombs, T. A.

    2010-08-01

    A model is presented for calculating the AC losses, magnetic field/current density distribution and critical currents of a circular superconducting pancake coil. The assumption is that the magnetic flux lines will lie parallel to the wide faces of tapes in the unpenetrated area of the coil. Instead of using an infinitely long stack to approximate the circular coil, this paper gives an exact circular coil model using elliptic integrals. A new efficient numerical method is introduced to yield more accurate and fast computation. The computation results are in good agreement with the assumptions. For a small value of the coil radius, there is an asymmetry along the coil radius direction. As the coil radius increases, this asymmetry will gradually decrease, and the AC losses and penetration depth will increase, but the critical current will decrease. We find that if the internal radius is equal to the winding thickness, the infinitely long stack approximation overestimates the loss by 10% and even if the internal radius is reduced to zero, the error is still only 60%. The infinitely long stack approximation is therefore adequate for most practical purposes. In addition, the comparison result shows that the infinitely long stack approximation saves computation time significantly.

  7. Cortico-muscular coupling and motor performance are modulated by 20 Hz transcranial alternating current stimulation (tACS) in Parkinson’s disease

    PubMed Central

    Krause, Vanessa; Wach, Claudia; Südmeyer, Martin; Ferrea, Stefano; Schnitzler, Alfons; Pollok, Bettina

    2014-01-01

    Parkinson’s disease (PD) is associated with pathologically altered oscillatory activity. While synchronized oscillations between 13 and 30 Hz are increased within a cortico-subcortical network, cortico-muscular coupling (CMC) is decreased. The present study aims at investigating the effect of non-invasive transcranial alternating current stimulation (tACS) of the primary motor cortex (M1) on motor symptoms and motor-cortical oscillations in PD. In 10 PD patients and 10 healthy control subjects, static isometric contraction, dynamic fast finger tapping, and diadochokinesia of the more severely affected hand were investigated prior to and shortly after tACS of the contralateral M1 at 10 Hz vs. 20 Hz vs. sham. During isometric contraction, neuromagnetic activity was recorded using magnetoencephalography. 20 Hz tACS attenuated beta band CMC during isometric contraction and amplitude variability during finger tapping in PD patients but not in healthy control subjects. 10 Hz tACS yielded no significant after-effects. The present data suggest that PD is associated with pathophysiological alterations which abet a higher responsiveness toward frequency-specific tACS – possibly due to pathologically altered motor-cortical oscillatory synchronization at frequencies between 13 and 30 Hz. PMID:24474912

  8. AC Loss Calculation of REBCO Cables by the Combination of Electric Circuit Model and 2D Finite Element Method

    NASA Astrophysics Data System (ADS)

    Noji, H.

    This study investigates the losses in a two conducting-layer REBCO cable fabricated by researchers at Furukawa Electric Co. Ltd. The losses were calculated using a combination of my electric circuit (EC) model with a two-dimensional finite element method (2D FEM). The helical pitches of the tapes in each layer, P1 and P2, were adjusted to equalize the current in both cable layers, although the loss calculation assumed infinite helical pitches and the same current in each layer at first. The results showed that the losses depended on the relative tape-position angle between the layers (θ/θ'), because the vertical field between adjacent tapes in the same layer varied with θ/θ'. When simulating the real cable, the helical pitches were adjusted and the layer currents were calculated by the EC model. These currents were input to the 2D FEM to compute the losses. The losses changed along the cable length because the difference between P1 and P2 altered the θ/θ' along this direction. The average angle-dependent and position-dependent losses were equal and closely approximated the measured losses. As an example to reduce the loss in this cable, the angle and the helical pitches were fixed at θ/θ' = 0.5 and P1 = P2 = 100 mm (S-direction). The calculation with these conditions indicated that the loss is about one order of magnitude lower than the measurement.

  9. Energy loss, equilibration, and thermodynamics of a baryon rich strongly coupled quark-gluon plasma

    NASA Astrophysics Data System (ADS)

    Rougemont, Romulo; Ficnar, Andrej; Finazzo, Stefano I.; Noronha, Jorge

    2016-04-01

    Lattice data for the QCD equation of state and the baryon susceptibility near the crossover phase transition (at zero baryon density) are used to determine the input parameters of a 5-dimensional Einstein-Maxwell-Dilaton holographic model that provides a consistent holographic framework to study both equilibrium and out-of-equilibrium properties of a hot and baryon rich strongly coupled quark-gluon plasma (QGP). We compare our holographic equation of state computed at nonzero baryon chemical potential, μ B , with recent lattice calculations and find quantitative agreement for the pressure and the speed of sound for μ B ≤ 400 MeV. This holographic model is used to obtain holographic predictions for the temperature and μ B dependence of the drag force and the Langevin diffusion coefficients associated with heavy quark jet propagation as well as the jet quenching parameter q and the shooting string energy loss of light quarks in the baryon dense plasma. We find that the energy loss of heavy and light quarks generally displays a nontrivial, fast-varying behavior as a function of the temperature near the crossover. Moreover, energy loss is also found to generally increase due to nonzero baryon density effects even though this strongly coupled liquid cannot be described in terms of well defined quasiparticle excitations. Furthermore, to get a glimpse of how thermalization occurs in a hot and baryon dense QGP, we study how the lowest quasinormal mode of an external massless scalar disturbance in the bulk is affected by a nonzero baryon charge. We find that the equilibration time associated with the lowest quasinormal mode decreases in a dense medium.

  10. Genetic characteristics of the couple with non-syndromic sensorineural hearing loss and fertility guidance

    PubMed Central

    Liu, Ri-Ming; Liu, Hong-Jie; Cong, Jiang-Lin; Sun, Ai-Ling; Du, Jiang-Dong; Sun, Cheng-Ming

    2015-01-01

    Purpose: We aim to report a genetic testing and fertility guidance for the deaf through analyzing pedigree and molecular genetic characteristics of the couple who have non-syndromic sensorineural hearing loss (NSHL). Methods: One of hospitalized congenial deaf couple and family members were included in this study. The wife was twin pregnant woman and her gestational age was 31+5 pregnant weeks. The DNA was extracted from peripheral blood and umbilical vein blood, respectively. Mutation screening of common deafness genes was performed in pregnant women and other family members. Nine common mutations in four major deafness genes, GJB2 (35delG, 176del16, 235delC, 299delAT), GjB3 (C538T), SLC26A4 (IVS7-2A>G, A2168G) and Mitochondrial 12S rRNA (A1555G, C1494T), were detected simultaneously with a microarray based method. SLC26A4 whole genome sequencing was carried out for the results of the DNA microarray. According to the test results, the couple chose abortion termination of pregnancy twins, and after one year obtained singleton pregnancy by artificial insemination by donor (AID). In week 16 of pregnancy, amniocentesis had been done to collect fetal somatic cell and extract DNA, and then the above tests had been repeated. Results: The couple had SLC26A4 combined heterozygous mutation. Both parents had SLC26A4 single heterozygous mutation. Twin fetuses had SLC26A4 combined heterozygous mutation. The probability of naturally being pregnant and bearing deaf children for the pregnant women was 100%. Fetus obtained by AID had SLC26A4 single heterozygous mutation. After the birth of the baby, her hearing has been normal. Conclusions: To reduce children with congenital deafness, screening high mutation sites by microarray, combined with pedigree analysis and gene sequencing is effective, and should be used as a routine inspection item for the deaf before marriage and pregnancy. On the basis of genetic testing for the couple with hearing loss, human assisted reproductive

  11. A Coupled Land Surface-Subsurface Biogeochemical Model for Aqueous and Gaseous Nitrogen Losses

    NASA Astrophysics Data System (ADS)

    Gu, C.; Maggi, F.; Riley, W.; Pan, L.; Xu, T.; Oldenburg, C.; Miller, N.

    2008-12-01

    In recent years concern has grown over the contribution of nitrogen (N) fertilizers to nitrate (NOB3PB-P) water pollution and atmospheric pollution of nitrous oxide (NB2BO), nitric oxide (NO), and ammonia (NHB3B). Characterizing the amount and species of N losses is therefore essential in developing a strategy to estimate and mitigate N leaching and emission to the atmosphere. Indeed, transformations of nitrogen depend strongly on water content, soil temperature, and nitrogen concentration. Land surface processes therefore have to be taken into account to properly characterize N biogeochemical cycling. However, most current nitrogen biogeochemical models take the land surface as the upper boundary by lumping the complex processes above the surface as known boundary conditions. In this study, an extant subsurface mechanistic N cycle model (TOUGHREACT-N) was coupled with the community land model (CLM). The resulting coupled model extends the modeling capability of TOUGHREACT-N to include the important energy, momentum, and moisture dynamics provided by CLM. The coupled model showed a significant impact of land-surface diurnal forcing on soil temperature and moisture and on nitrogen fluxes. We also discuss field applications of the model and discuss how temporal dynamics of nitrogen fluxes are affected by land surface processes.

  12. Minimalist coupled evolution model for stellar X-ray activity, rotation, mass loss, and magnetic field

    NASA Astrophysics Data System (ADS)

    Blackman, Eric G.; Owen, James E.

    2016-05-01

    Late-type main-sequence stars exhibit an X-ray to bolometric flux ratio that depends on {tilde{R}o}, the ratio of rotation period to convective turnover time, as {tilde{R}o}^{-ζ } with 2 ≤ ζ ≤ 3 for {tilde{R}o} > 0.13, but saturates with |ζ| < 0.2 for {tilde{R}o} < 0.13. Saturated stars are younger than unsaturated stars and show a broader spread of rotation rates and X-ray activity. The unsaturated stars have magnetic fields and rotation speeds that scale roughly with the square root of their age, though possibly flattening for stars older than the Sun. The connection between faster rotators, stronger fields, and higher activity has been established observationally, but a theory for the unified time-evolution of X-ray luminosity, rotation, magnetic field and mass loss that captures the above trends has been lacking. Here we derive a minimalist holistic framework for the time evolution of these quantities built from combining a Parker wind with new ingredients: (1) explicit sourcing of both the thermal energy launching the wind and the X-ray luminosity via dynamo produced magnetic fields; (2) explicit coupling of X-ray activity and mass-loss saturation to dynamo saturation (via magnetic helicity build-up and convection eddy shredding); (3) use of coronal equilibrium to determine how magnetic energy is divided into wind and X-ray contributions. For solar-type stars younger than the Sun, we infer conduction to be a subdominant power loss compared to X-rays and wind. For older stars, conduction is more important, possibly quenching the wind and reducing angular momentum loss. We focus on the time evolution for stars younger than the Sun, highlighting what is possible for further generalizations. Overall, the approach shows promise towards a unified explanation of all of the aforementioned observational trends.

  13. Coupling of Multiple Coulomb Scattering with Energy Loss and Straggling in HZETRN

    NASA Technical Reports Server (NTRS)

    Mertens, Christopher J.; Wilson, John W.; Walker, Steven A.; Tweed, John

    2007-01-01

    The new version of the HZETRN deterministic transport code based on Green's function methods, and the incorporation of ground-based laboratory boundary conditions, has lead to the development of analytical and numerical procedures to include off-axis dispersion of primary ion beams due to small-angle multiple Coulomb scattering. In this paper we present the theoretical formulation and computational procedures to compute ion beam broadening and a methodology towards achieving a self-consistent approach to coupling multiple scattering interactions with ionization energy loss and straggling. Our initial benchmark case is a 60 MeV proton beam on muscle tissue, for which we can compare various attributes of beam broadening with Monte Carlo simulations reported in the open literature.

  14. Loss of Gi G-Protein-Coupled Receptor Signaling in Osteoblasts Accelerates Bone Fracture Healing.

    PubMed

    Wang, Liping; Hsiao, Edward C; Lieu, Shirley; Scott, Mark; O'Carroll, Dylan; Urrutia, Ashley; Conklin, Bruce R; Colnot, Celine; Nissenson, Robert A

    2015-10-01

    G-protein-coupled receptors (GPCRs) are key regulators of skeletal homeostasis and are likely important in fracture healing. Because GPCRs can activate multiple signaling pathways simultaneously, we used targeted disruption of G(i) -GPCR or activation of G(s) -GPCR pathways to test how each pathway functions in the skeleton. We previously demonstrated that blockade of G(i) signaling by pertussis toxin (PTX) transgene expression in maturing osteoblastic cells enhanced cortical and trabecular bone formation and prevented age-related bone loss in female mice. In addition, activation of G(s) signaling by expressing the G(s) -coupled engineered receptor Rs1 in maturing osteoblastic cells induced massive trabecular bone formation but cortical bone loss. Here, we test our hypothesis that the G(i) and G(s) pathways also have distinct functions in fracture repair. We applied closed, nonstabilized tibial fractures to mice in which endogenous G(i) signaling was inhibited by PTX, or to mice with activated G(s) signaling mediated by Rs1. Blockade of endogenous G(i) resulted in a smaller callus but increased bone formation in both young and old mice. PTX treatment decreased expression of Dkk1 and increased Lef1 mRNAs during fracture healing, suggesting a role for endogenous G(i) signaling in maintaining Dkk1 expression and suppressing Wnt signaling. In contrast, adult mice with activated Gs signaling showed a slight increase in the initial callus size with increased callus bone formation. These results show that G(i) blockade and G(s) activation of the same osteoblastic lineage cell can induce different biological responses during fracture healing. Our findings also show that manipulating the GPCR/cAMP signaling pathway by selective timing of G(s) and G(i) -GPCR activation may be important for optimizing fracture repair. PMID:25917236

  15. Quantum noise effects with Kerr-nonlinearity enhancement in coupled gain-loss waveguides

    NASA Astrophysics Data System (ADS)

    He, Bing; Yan, Shu-Bin; Wang, Jing; Xiao, Min

    2015-05-01

    It is generally difficult to study the dynamical properties of a quantum system with both inherent quantum noises and nonperturbative nonlinearity. Due to the possibly drastic intensity increase of an input coherent light in gain-loss waveguide couplers with parity-time (PT ) symmetry, the Kerr effect from a nonlinearity added into the system can be greatly enhanced and is expected to create macroscopic entangled states of the output light fields with huge photon numbers. Meanwhile, quantum noises also coexist with the amplification and dissipation of the light fields. Under the interplay between the quantum noises and nonlinearity, the quantum dynamical behaviors of the systems become rather complicated. However, the important quantum noise effects have been mostly neglected in previous studies about nonlinear PT -symmetric systems. Here we present a solution to this nonperturbative quantum nonlinear problem, showing the real-time evolution of the system observables. The enhanced Kerr nonlinearity is found to give rise to a previously unknown decoherence effect that is irrelevant to the quantum noises and imposes a limit on the emergence of macroscopic nonclassicality. In contrast to what happens in linear systems, the quantum noises exert significant impact on the system dynamics and can create nonclassical light field states in conjunction with the enhanced Kerr nonlinearity. This study on the noise involved in quantum nonlinear dynamics of coupled gain-loss waveguides can help to better understand the quantum noise effects in many nonlinear systems.

  16. Coupling rainfall observations and satellite soil moisture for predicting event soil loss in Central Italy

    NASA Astrophysics Data System (ADS)

    Todisco, Francesca; Brocca, Luca; Termite, Loris Francesco; Wagner, Wolfgang

    2015-04-01

    specifically the analysis was focused on the evaluation of the effectiveness of coupling modeled or satellite-derived soil moisture with USLE-derived models in predicting event unit soil loss at the plot scale in a silty-clay soil in Central Italy. To this end was used the database of the Masse experimental station developed considering for a given erosive event (an event yielding a measurable soil loss) the simultaneous measures of the total runoff amount, Qe (mm), and soil loss per unit area, Ae (Mg-ha-1) at plot scale and of the rainfall data required to derive the erosivity factor Re according to Wischmeiser and Smith (1978), with a MIT=6 h (Bagarello et al., 2013; Todisco et al., 2012). To the purpose of this investigation only data collected on the λ = 22 m long plots were considered: 63 erosive events in the period 2008-2013, 18 occurred during the dry period (from June to September) and the other 45 in the complementary period (wet period). The models tested are the USLE/RUSLE and some USLE-derived formulations in which the event erosivity factor, Re, is corrected by the antecedent soil moisture, θ, and powered to an exponent α > 0 (α =1: linear model; α ≠ 1: power model). Both soil moisture data the satellite retrieved (θ = θsat) and the estimates (θ = θest) of Soil Water Balance model (Brocca et al., 2011) were tested. The results have been compared with those obtained by the USLE/RUSLE, USLE-M and USLE-MM models coupled with a parsimonious rainfall-runoff model, MILc, (Brocca et al. 2011) for the prediction of runoff volume (that in these models is the term used to correct the erosivity factor Re). The results showed that: including direct consideration of antecedent soil moisture and runoff in the event rainfall-runoff factor of the RUSLE/USLE enhanced the capacity of the model to account for variations in event soil loss when soil moisture and runoff volume are measured or predicted reasonably well; the accuracy of the original USLE/RUSLE model was

  17. Scaling law and general expression for transport ac loss of a rectangular thin strip with power-law E(J) relation

    NASA Astrophysics Data System (ADS)

    Chen, Du-Xing; Li, Shuo; Fang, Jin

    2015-12-01

    Transport ac loss Q of a superconducting rectangular thin strip obeying a power-law relation E∝Jn as a function of current amplitude Im may be, following Norris, expressed by normalized quantities as q(im). A scaling law is deduced that if Icf, Ic and f being the critical current and frequency, is multiplied by a positive constant C, then im and qm are multiplied by C 1 /(n - 1)and C 2 /(n - 1) , respectively. Based on this scaling law and the well-known Norris formula, the general function of q(im, n, f) is obtained graphically or analytically for any practical purpose, after accurate numerical computations on a set of q(im) at several values of n and a fixed value of f.

  18. The relationship between polymer waveguide optical interconnection end facet roughness and the optical input and output coupling losses

    NASA Astrophysics Data System (ADS)

    Baghsiahi, Hadi; Wang, Kai; Pitwon, Richard; Selviah, David R.

    2015-03-01

    The RMS surface roughness of an optical polymer waveguide end facet cut by a milling router and measured by AFM is investigated for a range of rotation speeds and translation speeds of the router. It was found that 1 flute (cutting edge) routers gave significantly less rough surfaces than 2 or 3 flute routers. The best results were achieved for a 1 flute router when the milling bit was inserted from the copper layer side of the board with a rotation speed of 15,000 rpm and a translation speed of 0.25 m/min which minimized the waveguide core end facet RMS roughness to 183 +/- 8 nm and gave input optical coupling loss of 1.7 dB +/- 0.5 dB and output optical coupling loss of 2.0 dB +/- 0.7 dB. The relationship between optical coupling loss at the input and output of the waveguides and waveguide end facet roughness is also investigated in this paper. The ratio of RMS roughness to autocorrelation length of the roughness is shown to have a quantified linear relationship with experimental measurements of optical insertion loss, input optical coupling loss and output optical coupling loss. A new fabrication technique for cut waveguide end facet treatment has been proposed and demonstrated which reduces the insertion loss by 2.60 dB +/- 1.3 dB which is more than that achieved by the closest available index matching fluid which gave 2.23 dB +/- 1.2 dB and which is far more robust for use in commercial products.

  19. Coupling rainfall observations and satellite soil moisture for predicting event soil loss in Central Italy

    NASA Astrophysics Data System (ADS)

    Todisco, Francesca; Brocca, Luca; Termite, Loris Francesco; Wagner, Wolfgang

    2015-04-01

    specifically the analysis was focused on the evaluation of the effectiveness of coupling modeled or satellite-derived soil moisture with USLE-derived models in predicting event unit soil loss at the plot scale in a silty-clay soil in Central Italy. To this end was used the database of the Masse experimental station developed considering for a given erosive event (an event yielding a measurable soil loss) the simultaneous measures of the total runoff amount, Qe (mm), and soil loss per unit area, Ae (Mg-ha-1) at plot scale and of the rainfall data required to derive the erosivity factor Re according to Wischmeiser and Smith (1978), with a MIT=6 h (Bagarello et al., 2013; Todisco et al., 2012). To the purpose of this investigation only data collected on the λ = 22 m long plots were considered: 63 erosive events in the period 2008-2013, 18 occurred during the dry period (from June to September) and the other 45 in the complementary period (wet period). The models tested are the USLE/RUSLE and some USLE-derived formulations in which the event erosivity factor, Re, is corrected by the antecedent soil moisture, θ, and powered to an exponent α > 0 (α =1: linear model; α ≠ 1: power model). Both soil moisture data the satellite retrieved (θ = θsat) and the estimates (θ = θest) of Soil Water Balance model (Brocca et al., 2011) were tested. The results have been compared with those obtained by the USLE/RUSLE, USLE-M and USLE-MM models coupled with a parsimonious rainfall-runoff model, MILc, (Brocca et al. 2011) for the prediction of runoff volume (that in these models is the term used to correct the erosivity factor Re). The results showed that: including direct consideration of antecedent soil moisture and runoff in the event rainfall-runoff factor of the RUSLE/USLE enhanced the capacity of the model to account for variations in event soil loss when soil moisture and runoff volume are measured or predicted reasonably well; the accuracy of the original USLE/RUSLE model was

  20. Antibacterial Ag/a-C nanocomposite coatings: The influence of nano-galvanic a-C and Ag couples on Ag ionization rates

    NASA Astrophysics Data System (ADS)

    Manninen, N. K.; Calderon, S.; Carvalho, I.; Henriques, M.; Cavaleiro, A.; Carvalho, S.

    2016-07-01

    Biofilm formation has been pointed as a major concern in different industrial applications, namely on biomedical implants and surgical instruments, which has prompted the development of new strategies for production of efficient antimicrobial surfaces. In this work, nano-galvanic couples were created to enhance the antibacterial properties of silver, by embedding it into amorphous carbon (a-C) matrix. The developed Ag/a-C nanocomposite coatings, deposited by magnetron sputtering, revealed an outstanding antibacterial activity against Staphylococcus epidermidis, promoting a total reduction in biofilm formation with no bacteria counts in all dilution. The open circuit potential (OCP) tests in 0.9% NaCl confirmed that a-C shows a positive OCP value, in contrast to Ag coating, thus enhancing the ionization of biocidal Ag+ due to the nano-galvanic couple activation. This result was confirmed by the inductively coupled plasma-optical emission spectroscopy (ICP-OES), which revealed a higher Ag ionization rate in the nanocomposite coating in comparison with the Ag coating. The surface of Ag/a-C and Ag coatings immersed in 0.9% NaCl were monitored by scanning electron microscopy (SEM) over a period of 24 h, being found that the Ag ionization determined by ICP-OES was accompanied by an Ag nanoparticles coalescence and agglomeration in Ag/a-C coating.

  1. Uplink Scheduling and Adjacent-Channel Coupling Loss Analysis for TD-LTE Deployment

    PubMed Central

    Yeo, Woon-Young; Moon, Sung Ho

    2014-01-01

    TD-LTE, one of the two duplexing modes in LTE, operates in unpaired spectrum and has the advantages of TDD-based technologies. It is expected that TD-LTE will be more rapidly deployed in near future and most of WiMax operators will upgrade their networks to TD-LTE gradually. Before completely upgrading to TD-LTE, WiMax may coexist with TD-LTE in an adjacent frequency band. In addition, multiple TD-LTE operators may deploy their networks in adjacent bands. When more than one TDD network operates in adjacent frequency bands, severe interference may happen due to adjacent channel interference (ACI) and unsynchronized operations. In this paper, coexistence issues between TD-LTE and other systems are analyzed and coexistence requirements are provided. This paper has three research objectives. First, frame synchronization between TD-LTE and WiMax is discussed by investigating possible combinations of TD-LTE and WiMax configurations. Second, an uplink scheduling algorithm is proposed to utilize a leakage pattern of ACI in synchronized operations. Third, minimum requirements for coexistence in unsynchronized operations are analyzed by introducing a concept of adjacent-channel coupling loss. From the analysis and simulation results, we can see that coexistence of TD-LTE with other TDD systems is feasible if the two networks are synchronized. For the unsynchronized case, some special cell-site engineering techniques may be required to reduce the ACI. PMID:24707214

  2. Uplink scheduling and adjacent-channel coupling loss analysis for TD-LTE deployment.

    PubMed

    Yeo, Woon-Young; Moon, Sung Ho; Kim, Jae-Hoon

    2014-01-01

    TD-LTE, one of the two duplexing modes in LTE, operates in unpaired spectrum and has the advantages of TDD-based technologies. It is expected that TD-LTE will be more rapidly deployed in near future and most of WiMax operators will upgrade their networks to TD-LTE gradually. Before completely upgrading to TD-LTE, WiMax may coexist with TD-LTE in an adjacent frequency band. In addition, multiple TD-LTE operators may deploy their networks in adjacent bands. When more than one TDD network operates in adjacent frequency bands, severe interference may happen due to adjacent channel interference (ACI) and unsynchronized operations. In this paper, coexistence issues between TD-LTE and other systems are analyzed and coexistence requirements are provided. This paper has three research objectives. First, frame synchronization between TD-LTE and WiMax is discussed by investigating possible combinations of TD-LTE and WiMax configurations. Second, an uplink scheduling algorithm is proposed to utilize a leakage pattern of ACI in synchronized operations. Third, minimum requirements for coexistence in unsynchronized operations are analyzed by introducing a concept of adjacent-channel coupling loss. From the analysis and simulation results, we can see that coexistence of TD-LTE with other TDD systems is feasible if the two networks are synchronized. For the unsynchronized case, some special cell-site engineering techniques may be required to reduce the ACI. PMID:24707214

  3. Terahertz quantum cascade laser coupled with high efficiency to the low loss optical modes of cylindrical hollow-core waveguides

    NASA Astrophysics Data System (ADS)

    Vitiello, Miriam S.; Xu, J. H.; Beltram, F.; Tredicucci, A.; Mitrofanov, O.; Harrington, James A.; Beere, H. E.; Ritchie, D. A.

    2011-10-01

    We demonstrate that azimuthally polarized micro-ring THz quantum-cascade lasers can be coupled to hollow metallic waveguides with efficiencies >=96% and perfectly matched with the TE01 waveguide mode, giving attenuation losses < 3dB/m. The use of Ag coated-flexible pipe waveguides allows propagation of either vertically polarized or azimuthally polarized QCL beams with propagation losses as low as 2.1-4.4 dB/m and bending losses lower than 1.2 dB.

  4. AC Stark effect in a spin-orbit mixed quantum states in a five-level molecular system coupled by three lasers

    NASA Astrophysics Data System (ADS)

    Qi, Jianbing

    2016-05-01

    The interaction of the spin orbital motion of electrons can mix quantum states with different spin multiplicity. Thus the mixed states can carry both characteristics of the two states depending on the mixing coefficients. The spin-orbit coupled rovibrational levels in diatomic alkali are ubiquitous. These levels are classified as singlet states (if the total spin is zero) and triplet states (if the total spin is one), respectively. A transition from a singlet level can only go to singlet levels and a triplet only to triplet levels. The spin-orbit coupled states can be used as a gateway to access some normally prohibited transitions. By coupling the mixed states to an auxiliary quantum state with lasers, the coupling coefficient of two mixed singlet-triplet molecular states can be modified by ac Stark effect via varying the Rabi frequency of the coupling lasers and the detuning of the laser frequency, We use density matrix equations and a five-level molecular model to show that a coupled singlet-triplet pair of rovibrational levels can be used as a channel to enhance the probability of accessing target quantum states.

  5. Study of AC Magnetic Properties and Core Losses of Fe/Fe3O4-epoxy Resin Soft Magnetic Composite

    NASA Astrophysics Data System (ADS)

    Laxminarayana, T. A.; Manna, Subhendu Kumar; Fernandes, B. G.; Venkataramani, N.

    Soft Magnetic Composites (SMC) were prepared by coating of nanocrystalline Fe3O4 particles, synthesized by co-precipitation method, on atomized iron powder of particle size less than 53 μm in size using epoxy resin as a binder between iron and Fe3O4. Fe3O4 was chosen, for its high electric resistivity and suitable magnetic properties, to keep the coating layer magnetic and seek improvement to the magnetic properties of SMC. SEM images and XRD patterns were recorded in order to investigate the coatings on the surface of iron powder. A toroid was prepared by cold compaction of coated iron powder at 1050 MPa and subsequently cured at 150˚C for 1 hr in argon atmosphere. For comparison of properties, a toroid of uncoated iron powder was also compacted at 1050 MPa and annealed at 600˚C for 2 hr in argon atmosphere. The coated iron powder composite has a resistivity of greater than 200 μΩm, measured by four probe method. A comparison of Magnetic Hysteresis loops and core losses using B-H Loop tracer in the frequency range 0 to 1500 Hz on the coated and uncoated iron powder is reported.

  6. Major loss of junctional coupling during mitosis in early mouse embryos

    PubMed Central

    1986-01-01

    Junctional coupling was assessed during the transition from the fourth to the fifth cell cycle of mouse embryogenesis by injection of the dye carboxyfluorescein and by measurement of electrical continuity between cells. Junctional coupling, which arises de novo in early 8-cell mouse embryos, subsequently becomes reduced towards the end of the cell cycle as the blastomeres enter into mitosis. Arrest of the cell cycle in metaphase by nocodazole, an inhibitor of tubulin polymerization, reveals that cell coupling becomes undetectable at mitosis. Junctional coupling then is resumed during interphase of the 16-cell stage. Nocodazole itself has no effect on junctional coupling in interphase cells, regardless of the extent of intercellular flattening, whereas taxol, a microtubule-stabilizing agent, does reduce the extent of coupling in interphase cells. PMID:2868015

  7. Energy-loss rate of a fast particle in two-dimensional semiconductors with Rashba spin-orbit coupling

    SciTech Connect

    Feng, W.; Tawfiq, Asya; Cao, J. C.; Zhang, C.

    2013-02-04

    The energy-loss rate (ELR) of a charged particle in a two-dimensional semiconductor with Rashba spin-orbit coupling is studied. Our model takes into account of the temperature and density dependence of the electronic properties of the Rashba system. The energy and temperature dependence of the ELR are presented. It is found that a finite Rashba spin-orbit coupling offers a mechanism of tuning the mean scattering time in narrow-gap semiconductors. With a change of Rashba parameter of around 3 times, the mean scattering time can change by one to two orders of magnitude.

  8. CMP-Neu5Ac Hydroxylase Null Mice as a Model for Studying Metabolic Disorders Caused by the Evolutionary Loss of Neu5Gc in Humans

    PubMed Central

    Kwon, Deug-Nam; Choi, Yun-Jung; Cho, Ssang-Goo; Park, Chankyu; Seo, Han Geuk; Song, Hyuk; Kim, Jin-Hoi

    2015-01-01

    The purpose of this study was to identify the modification/turnover of gene products that are altered in humans due to evolutionary loss of Neu5Gc. CMP-Neu5Ac hydroxylase- (Cmah-) deficient mice show the infiltration of Kupffer cells within liver sinusoids, whereas body and liver weight develop normally. Pathway analysis by use of Illumina MouseRef-8 v2 Expression BeadChip provided evidence that a number of biological pathways, including the glycolysis, gluconeogenesis, TCA cycle, and pentose phosphate pathways, as well as glycogen metabolism-related gene expression, were significantly upregulated in Cmah-null mice. The intracellular glucose supply in Cmah-null mice resulted in mitochondrial dysfunction, oxidative stress, and the advanced glycation end products accumulation that could further induce oxidative stress. Finally, low sirtuin-1 and sirtuin-3 gene expressions due to higher NADH/NAD in Cmah-null mice decreased Foxo-1 and MnSOD gene expression, suggesting that oxidative stress may result in mitochondrial dysfunction in Cmah-null mouse. The present study suggests that mice with CMAH deficiency can be taken as an important model for studying metabolic disorders in humans. PMID:26558285

  9. Ambiguous Loss after Lesbian Couples with Children Break up: A Case for Same-Gender Divorce

    ERIC Educational Resources Information Center

    Allen, Katherine R.

    2007-01-01

    The theory of ambiguous loss is applied to structural ambiguity and personal transcendence in the parent-child relationship following a same-gender relational ending. Working recursively through the six guidelines of ambiguous loss (finding meaning, tempering mastery, reconstructing identity, normalizing ambivalence, revising attachment, and…

  10. Ac-Induced Instability at the Xanthophyllic Locus of Tomato

    PubMed Central

    Peterson, P. W.; Yoder, J. I.

    1993-01-01

    To detect genomic instability caused by Ac elements in transgenic tomatoes, we used the incompletely dominant mutation Xanthophyllic-1 (Xa-1) as a whole plant marker gene. Xa-1 is located on chromosome 10 and in the heterozygote state causes leaves to be yellow. Transgenic Ac-containing tomato plants which differed in the location and number of their Ac elements were crossed to Xa-1 tester lines and F(1) progeny were scored for aberrant somatic sectoring. Of 800 test and control F(1) progeny screened, only four plants had aberrantly high levels of somatic sectors. Three of the plants had twin sectors consisting of green tissue adjacent to white tissue, and the other had twin sectors comprised of green tissue adjacent to tissue more yellow than the heterozygote background. Sectoring was inherited and the two sectoring phenotypes mapped to opposite homologs of chromosome 10; the green/yellow sectoring phenotype mapped in coupling to Xa-1 while the green/white sectoring phenotype mapped in repulsion. The two sectoring phenotypes cosegregated with different single, non-rearranged Acs, and loss of these Acs from the genome corresponded to the loss of sectoring. Sectoring was still observed after transposition of the Ac to a new site which indicated that sectoring was not limited to a single locus. In both sectored lines, meiotic recombination of the sectoring Ac to the opposite homolog caused the phenotype to switch between the green/yellow and the green/white phenotypes. Thus the two different sectoring phenotypes arose from the same Ac-induced mechanism; the phenotype depended on which chromosome 10 homolog the Ac was on. We believe that the twin sectors resulted from chromosome breakage mediated by a single intact, transposition-competent Ac element. PMID:8394266

  11. Corona Formation and Heat Loss on Venus by Coupled Upwelling and Delamination

    NASA Technical Reports Server (NTRS)

    Smrekar, Suzanne E.; Stofan, Ellen R.

    1997-01-01

    Coronae are volcanotectonic features that are unique to Venus and are interpreted to be small-scale upwellings. A model in which upwelling causes delamination at the edge of the plume head, along with deformation of a pre-existing depleted mantel Layer, can produce the full range of topographic forms of coronae. If half of the coronae are active, delamination of the lower lithosphere could account for about 10% of venus's heat loss, with another 15% due to upwelling. Delamination may occur in other geologic enviroment and could help account for 'Venus' heat loss 'deficit'.

  12. Integrated InP-InGaAsP tunable coupled ring optical bandpass filters with zero insertion loss.

    PubMed

    Guzzon, Robert S; Norberg, Erik J; Parker, John S; Johansson, Leif A; Coldren, Larry A

    2011-04-11

    Second and third-order monolithically integrated coupled ring bandpass filters are demonstrated in the InP-InGaAsP material system with active semiconductor optical amplifiers (SOAs) and current injection phase modulators (PMs). Such integration achieves a high level of tunability and precise generation of optical filters in the RF domain at telecom wavelengths while simultaneously compensating for device insertion loss. Passband bandwidth tunability of 3.9 GHz to 7.1 GHz and stopband extinction up to 40 dB are shown for third-order filters. Center frequency tunability over a full free spectral range (FSR) is demonstrated, allowing for the placement of a filter anywhere in the telecom C-band. A Z-transform representation of coupled resonator filters is derived and compared with experimental results. A theoretical description of filter tunability is presented. PMID:21503092

  13. Impact of Arctic sea ice loss on large-scale atmospheric circulation based on fully-coupled sensitivity experiments

    NASA Astrophysics Data System (ADS)

    Oudar, Thomas; Sanchez, Emilia; Terray, Laurent; Chauvin, Fabrice

    2016-04-01

    Arctic sea ice decline in the recent decades has been reported in observational studies. Modeling studies have confirmed that this downward trend in Arctic sea ice is mainly caused by increasing Greenhouse Gases (GHGs) concentrations into the atmosphere. The IPCC-AR5 report concluded that Arctic sea ice will continue to decrease and is projected to disappear in the middle of the 21st century, yielding to a ice-free region during boreal summer season. Arctic sea ice loss is expected to strongly impact the climate system. Recently, the climate community has conducted a number of studies to evaluate and understand the Arctic sea ice loss implications on climate. While some studies have shown that Arctic sea ice decline can significantly affect the large-scale atmospheric dynamics at high and mid-latitudes of the Northern Hemisphere, by altering the storm-tracks, the jet stream (position and strength) and the planetary waves, large uncertainties remain due to a low signal-to-noise ratio and experimental protocol differences leading to a large inter-model spread. In this work, we investigate the respective roles of Arctic sea ice loss and GHGs increase on the atmospheric dynamics by means of an idealized experimental set-up that uses the coupled model CNRM-CM5. The experimental set-up, based on a flux correction technique, will allow separating the contributions of Arctic sea ice loss from the GHGs increasing. We will focus mainly on the atmospheric circulation response in the Northern Hemisphere and on the associated synoptic variability, represented by the storm-tracks. We show that Arctic sea ice loss is responsible for an equatorward shift of the northern hemisphere jet, which is opposed to the GHGs effect. Finally we show that these shifts are consistent with the storm-tracks response.

  14. Thermionic triode generates ac power

    NASA Technical Reports Server (NTRS)

    Kniazzeh, A. G. F.; Scharz, F. C.

    1970-01-01

    Electrostatic grid controls conduction cycle of thermionic diode to convert low dc output voltages to high ac power without undesirable power loss. An ac voltage applied to the grid of this new thermionic triode enables it to convert heat directly into high voltage electrical power.

  15. Ultra-low loss fully-etched grating couplers for perfectly vertical coupling compatible with DUV lithography tools

    NASA Astrophysics Data System (ADS)

    Dabos, G.; Pleros, N.; Tsiokos, D.

    2016-03-01

    Hybrid integration of VCSELs onto silicon-on-insulator (SOI) substrates has emerged as an attractive approach for bridging the gap between cost-effective and energy-efficient directly modulated laser sources and silicon-based PICs by leveraging flip-chip (FC) bonding techniques and silicon grating couplers (GCs). In this context, silicon GCs, should comply with the process requirements imposed by the complimentary-metal-oxide-semiconductor manufacturing tools addressing in parallel the challenges originating from the perfectly vertical incidence. Firstly, fully etched GCs compatible with deep-ultraviolet lithography tools offering high coupling efficiencies are imperatively needed to maintain low fabrication cost. Secondly, GC's tolerance to VCSEL bonding misalignment errors is a prerequisite for practical deployment. Finally, a major challenge originating from the perfectly vertical coupling scheme is the minimization of the direct back-reflection to the VCSEL's outgoing facet which may destabilize its operation. Motivated from the above challenges, we used numerical simulation tools to design an ultra-low loss, bidirectional VCSEL-to-SOI optical coupling scheme for either TE or TM polarization, based on low-cost fully etched GCs with a Si-layer of 340 nm without employing bottom reflectors or optimizing the buried-oxide layer. Comprehensive 2D Finite-Difference-Time- Domain simulations have been performed. The reported GC layout remains fully compatible with the back-end-of-line (BEOL) stack associated with the 3D integration technology exploiting all the inter-metal-dielectric (IMD) layers of the CMOS fab. Simulation results predicted for the first time in fully etched structures a coupling efficiency of as low as -0.87 dB at 1548 nm and -1.47 dB at 1560 nm with a minimum direct back-reflection of -27.4 dB and -14.2 dB for TE and TM polarization, respectively.

  16. Coupled Ocean-Atmosphere Loss of Refractory Marine Dissolved Organic Matter

    NASA Astrophysics Data System (ADS)

    Kieber, D. J.; Keene, W. C.; Frossard, A. A.; Long, M. S.; Russell, L. M.; Maben, J. R.; Kinsey, J. D.; Tyssebotn, I. M.; Quinn, P.; Bates, T. S.

    2013-12-01

    Marine aerosol produced in the oceans from bursting bubbles and breaking waves is number dominated by submicron aerosol that are highly enriched in marine organic matter relative to seawater. Recent studies suggest that these organic-rich, submicron aerosol have a major impact on tropospheric chemistry and climate. It has been assumed this marine-derived aerosol organic matter is of recent origin stemming from biological activity in the photic zone. However, we deployed a marine aerosol generator on a recent cruise in the Sargasso Sea with seawater collected from 2500 m and showed that the aerosol generated from this seawater was enriched with organic matter to the same level as observed in surface Sargasso seawater, implying that the marine organic matter flux from the oceans into atmospheric aerosol is partly due to marine organic matter not of recent origin. We propose that marine aerosol production and subsequent physical and photochemical atmospheric evolution is the main process whereby old, refractory organic matter is removed from the oceans, thereby closing the carbon budget in the oceans and solving a long-standing conundrum regarding the removal mechanism for this organic matter in the sea. The implications of this study for couplings in the ocean-atmosphere cycling of organic matter will be discussed.

  17. Radical loss in the atmosphere from Cu-Fe redox coupling in aerosols

    NASA Astrophysics Data System (ADS)

    Mao, J.; Fan, S.; Jacob, D. J.; Travis, K. R.

    2013-01-01

    The hydroperoxyl radical (HO2) is a major precursor of OH and tropospheric ozone. OH is the main atmospheric oxidant, while tropospheric ozone is an important surface pollutant and greenhouse gas. Standard gas-phase models for atmospheric chemistry tend to overestimate observed HO2 concentrations, and this has been tentatively attributed to heterogeneous uptake by aerosol particles. It is generally assumed that HO2 uptake by aerosol involves conversion to H2O2, but this is of limited efficacy as an HO2 sink because H2O2 can photolyze to regenerate OH and from there HO2. Joint atmospheric observations of HO2 and H2O2 suggest that HO2 uptake by aerosols may in fact not produce H2O2. Here we propose a catalytic mechanism involving coupling of the transition metal ions Cu(I)/Cu(II) and Fe(II)/Fe(III) to rapidly convert HO2 to H2O in aqueous aerosols. The implied HO2 uptake and conversion to H2O significantly affects global model predictions of tropospheric OH, ozone, carbon monoxide (CO) and other species, improving comparisons to observations in the GEOS-Chem model. It represents a previously unrecognized positive radiative forcing of aerosols through the effects on the chemical budgets of major greenhouse gases including methane and hydrofluorocarbons (HFCs).

  18. Plasmonic phase modulator based on novel loss-overcompensated coupling between nanoresonator and waveguide

    NASA Astrophysics Data System (ADS)

    Im, Song-Jin; Ho, Gum-Song; Yang, Da-Jie; Hao, Zhong-Hua; Zhou, Li; Kim, Nam-Chol; Kim, Il-Gwang; Wang, Qu-Quan

    2016-01-01

    We present that surface plasmon polariton, side-coupled to a gain-assisted nanoresonator where the absorption is overcompensated, exhibits a prominent phase shift up to π maintaining the flat unity transmission across the whole broad spectra. Bandwidth of this plasmonic phase shift can be controlled by adjusting the distance between the plasmonic waveguide and the nanoresonator. For a moderate distance, within bandwidth of 100 GHz, the phase shift and transmission are constantly maintained. The plasmonic phase can be shift-keying-modulated by a pumping signal in the gain-assisted nanoresonator. A needed length in our approach is of nanoscale while already suggested types of plasmonic phase modulator are of micrometer scale in length. The energy consumption per bit, which benefits from the nano size of this device, is ideally low on the order of 10 fJ/bit. The controllable plasmonic phase shift can find applications in nanoscale Mach-Zehnder interferometers and other phase-sensitive devices as well as directly in plasmonic phase shift keying modulators.

  19. Plasmonic phase modulator based on novel loss-overcompensated coupling between nanoresonator and waveguide.

    PubMed

    Im, Song-Jin; Ho, Gum-Song; Yang, Da-Jie; Hao, Zhong-Hua; Zhou, Li; Kim, Nam-Chol; Kim, Il-Gwang; Wang, Qu-Quan

    2016-01-01

    We present that surface plasmon polariton, side-coupled to a gain-assisted nanoresonator where the absorption is overcompensated, exhibits a prominent phase shift up to π maintaining the flat unity transmission across the whole broad spectra. Bandwidth of this plasmonic phase shift can be controlled by adjusting the distance between the plasmonic waveguide and the nanoresonator. For a moderate distance, within bandwidth of 100 GHz, the phase shift and transmission are constantly maintained. The plasmonic phase can be shift-keying-modulated by a pumping signal in the gain-assisted nanoresonator. A needed length in our approach is of nanoscale while already suggested types of plasmonic phase modulator are of micrometer scale in length. The energy consumption per bit, which benefits from the nano size of this device, is ideally low on the order of 10 fJ/bit. The controllable plasmonic phase shift can find applications in nanoscale Mach-Zehnder interferometers and other phase-sensitive devices as well as directly in plasmonic phase shift keying modulators. PMID:26733338

  20. Radical loss in the atmosphere from Cu-Fe redox coupling in aerosols

    NASA Astrophysics Data System (ADS)

    Mao, J.; Fan, S.; Jacob, D. J.; Travis, K. R.

    2012-10-01

    The hydroperoxyl radical (HO2) is a major precursor of OH and tropospheric ozone. OH is the main atmospheric oxidant, while tropospheric ozone is an important surface pollutant and greenhouse gas. Standard gas-phase models for atmospheric chemistry tend to overestimate observed HO2 concentrations, and this has been tentatively attributed to heterogeneous uptake by aerosol particles. It is generally assumed that HO2 uptake by aerosol involve conversion to H2O2, but this is of limited efficacy as an HO2 sink because H2O2 can photolyze to regenerate OH and from there HO2. Joint atmospheric observations of HO2 and H2O2 suggest that HO2 uptake by aerosols may in fact not produce H2O2. Here we propose a catalytic mechanism involving coupling of the transition metal ions (TMI) Cu(I)/Cu(II) and Fe(II)/Fe(III) to rapidly convert HO2 to H2O in aerosols. The implied HO2 uptake significantly affects global model predictions of tropospheric OH, ozone, and other species, improving comparisons to observations, and may have a major and previously unrecognized impact on atmospheric oxidant chemistry.

  1. Radical loss in the atmosphere from Cu-Fe redox coupling in aerosols

    NASA Astrophysics Data System (ADS)

    Mao, J.; Fan, S.; Jacob, D. J.; Travis, K.; Naik, V.; Horowitz, L. W.

    2012-12-01

    The hydroperoxyl radical (HO2) is a major precursor of OH and tropospheric ozone. OH is the main atmospheric oxidant, while tropospheric ozone is an important surface pollutant and greenhouse gas. Standard gas-phase models for atmospheric chemistry tend to overestimate observed HO2 concentrations, and this has been tentatively attributed to heterogeneous uptake by aerosol particles. It is generally assumed that HO2 uptake by aerosol involves conversion to H2O2, but this is of limited efficacy as an HO2 sink because H2O2 can photolyze to regenerate OH and from there HO2. Joint atmospheric observations of HO2 and H2O2 suggest that HO2 uptake by aerosols may in fact not produce H2O2. Here we propose a catalytic mechanism involving coupling of the transition metal ions (TMI) Cu(I)/Cu(II) and Fe(II)/Fe(III) to rapidly convert HO2 to H2O in aerosols. The implied HO2 uptake significantly affects global model predictions of tropospheric OH, ozone, and other species, improving comparisons to observations, and may have a major and previously unrecognized impact on atmospheric oxidant chemistry.

  2. Plasmonic phase modulator based on novel loss-overcompensated coupling between nanoresonator and waveguide

    PubMed Central

    Im, Song-Jin; Ho, Gum-Song; Yang, Da-Jie; Hao, Zhong-Hua; Zhou, Li; Kim, Nam-Chol; Kim, Il-Gwang; Wang, Qu-Quan

    2016-01-01

    We present that surface plasmon polariton, side-coupled to a gain-assisted nanoresonator where the absorption is overcompensated, exhibits a prominent phase shift up to π maintaining the flat unity transmission across the whole broad spectra. Bandwidth of this plasmonic phase shift can be controlled by adjusting the distance between the plasmonic waveguide and the nanoresonator. For a moderate distance, within bandwidth of 100 GHz, the phase shift and transmission are constantly maintained. The plasmonic phase can be shift-keying-modulated by a pumping signal in the gain-assisted nanoresonator. A needed length in our approach is of nanoscale while already suggested types of plasmonic phase modulator are of micrometer scale in length. The energy consumption per bit, which benefits from the nano size of this device, is ideally low on the order of 10 fJ/bit. The controllable plasmonic phase shift can find applications in nanoscale Mach–Zehnder interferometers and other phase-sensitive devices as well as directly in plasmonic phase shift keying modulators. PMID:26733338

  3. COUPLING

    DOEpatents

    Hawke, B.C.

    1963-02-26

    This patent relates to a releasable coupling connecting a control rod to a control rod drive. This remotely operable coupling mechanism can connect two elements which are laterally and angviarly misaligned, and provides a means for sensing the locked condition of the elements. The coupling utilizes a spherical bayonet joint which is locked against rotation by a ball detent lock. (AEC)

  4. Strong Light-Matter Coupling and Hybridization of Molecular Vibrations in a Low-Loss Infrared Microcavity.

    PubMed

    Muallem, Merav; Palatnik, Alexander; Nessim, Gilbert D; Tischler, Yaakov R

    2016-06-01

    Hybridized polaritons are generated by simultaneously coupling two vibrational modes of two different organic materials to the resonance of a low-loss infrared optical microcavity. A thin film of poly methyl methacrylate with solvent molecules of dimethylformamide trapped inside provided two spectrally narrow, closely spaced carbonyl stretches with absorption peaks at 1731 and 1678 cm(-1). Situating this film in a microcavity based on Ge/ZnS distributed Bragg reflector mirrors produced three distinct polariton branches in the dispersion relation due to hybridization of the vibrational resonances. Two anticrossings were observed with Rabi splittings of 9.6 and 5.2 meV, between the upper-to-middle and middle-to-lower polariton branches, respectively. This system marks the first demonstration of polariton hybridization between a solid and solvent molecules and can open new paths toward chemical reaction modification and energy transfer studies in the mid-infrared spectral range. PMID:27159242

  5. Studies of superspin glass state and AC-losses in La0.7Sr0.3MnO3 nanoparticles obtained by high-energy ball-milling

    NASA Astrophysics Data System (ADS)

    Phong, P. T.; Manh, D. H.; Nguyen, L. H.; Tung, D. K.; Phuc, N. X.; Lee, I.-J.

    2014-11-01

    Single-phase perovskite compound La0.7Sr0.3MnO3 was synthesized by a high-energy ball milling method. Nanoparticle nature of this manganite with the average particle diameter of 11 nm was revealed from structure and morphology characterizations. The results of ac magnetic susceptibility measurements show that the system can be described as an ensemble of interacting magnetic nanoparticles, which indicates that the dipole-dipole interactions are strong enough to create superspin glass state in the sample. Furthermore, the specific loss power which is exhausted on the irradiation of an ensemble of particles with a magnetic field has been calculated and measured experimentally.

  6. Improvements in Fabrication of 3D SU-8 Prisms for Low-Coupling-Loss Interconnections Between Fibers and Waveguides

    NASA Astrophysics Data System (ADS)

    Nguyen, Minh-Hang; Chu, Thi-Xuan; Nguyen, Long; Nguyen, Hai-Binh; Lee, Chun-Wei; Tseng, Fan-Gang; Chen, Te-Chang; Lee, Ming-Chang

    2016-07-01

    Fabrication of three-dimensional (3D) SU-8 (an epoxy-based negative photoresist from MicroChem) prisms as low-loss couplers for interconnection between optical components, particularly optical fibers and silicon-on-isolator waveguides (SOI WGs), which have mismatched mode sizes, has been investigated. With an interfacial structure formed by a 3D SU-8 prism partly overlaying an SOI WG end with a portion of buried oxide (BOX) removed under the interface, low-loss coupling is ensured and the transmission efficiency can reach 70%. To fabricate these 3D SU-8 prisms, a simple method with two photolithography steps was used for SU-8 hinges and CYTOP (an amorphous fluoropolymer from AGC Chemicals) prism windows, with mild soft and hard bakes, to define the prism profiles with diluted SU-8 filled in the CYTOP prism windows. A buffered oxide etchant is used to remove BOX parts under the interfaces. Some of the fabricated structures were tested, demonstrating the contribution of overlaying SU-8 prisms to the transmission efficiency of optical interconnections between fibers and SOI WGs.

  7. Evaluation of 1100 couples with recurrent pregnancy loss using conventional cytogenetic, PGD, and PGS: hype or hope.

    PubMed

    Farahmand, Kamelia; Kalantari, Hamid; Fakhri, Mostafa; Fazeli, Abolhasan Shahzadeh; Moradi, Shabnam Zari; Almadani, Navid; Hashemi, Mehrdad; Gourabi, Hamid; Mohseni-Meybodi, Anahita

    2016-06-01

    Recurrent pregnancy loss (RPL) is an important clinical problem, mostly resulting from chromosomal or genetic defects, while in 30-60% of cases, it is idiopathic. The aim of this study is to evaluate the frequency and types of chromosomal abnormalities, also pre-implantation genetic diagnosis (PGD) and pre-implantation genetic screening (PGS) outcomes among Iranian couples with RPL. This retrospective study was conducted on 1100 Iranian couples (2200 individuals) with RPL referred to Royan Institute between 2008 and 2014. Karyotyping had been performed using standard cytogenetic techniques. PGD results of RPL patients with abnormal karyotypes and PGS results of RPL patients with normal karyotypes were also analyzed. The frequency of chromosomal abnormalities in these patients was 4.95%. Women demonstrated more abnormalities (6.82%) in comparison to men (3.09%). The successful rate of pregnancy after PGD and PGS was 52 and 18.64%, respectively. The observation of 4.95% chromosomal abnormalities among the patients with RPL could support this hypothesis that there is a direct relationship between chromosomal abnormalities and RPL. More than half of the patients who underwent PGD had successful pregnancy; therefore, this approach can improve the success rate of pregnancy in them. The results of PGS cycles showed that this technique could increase the live birth rate in RPL patients. PMID:26854690

  8. Small RNAs prevent transcription-coupled loss of histone H3 lysine 9 methylation in Arabidopsis thaliana.

    PubMed

    Enke, Raymond A; Dong, Zhicheng; Bender, Judith

    2011-10-01

    In eukaryotes, histone H3 lysine 9 methylation (H3K9me) mediates silencing of invasive sequences to prevent deleterious consequences including the expression of aberrant gene products and mobilization of transposons. In Arabidopsis thaliana, H3K9me maintained by SUVH histone methyltransferases (MTases) is associated with cytosine methylation (5meC) maintained by the CMT3 cytosine MTase. The SUVHs contain a 5meC binding domain and CMT3 contains an H3K9me binding domain, suggesting that the SUVH/CMT3 pathway involves an amplification loop between H3K9me and 5meC. However, at loci subject to read-through transcription, the stability of the H3K9me/5meC loop requires a mechanism to counteract transcription-coupled loss of H3K9me. Here we use the duplicated PAI genes, which stably maintain SUVH-dependent H3K9me and CMT3-dependent 5meC despite read-through transcription, to show that when PAI sRNAs are depleted by dicer ribonuclease mutations, PAI H3K9me and 5meC levels are reduced and remaining PAI 5meC is destabilized upon inbreeding. The dicer mutations confer weaker reductions in PAI 5meC levels but similar or stronger reductions in PAI H3K9me levels compared to a cmt3 mutation. This comparison indicates a connection between sRNAs and maintenance of H3K9me independent of CMT3 function. The dicer mutations reduce PAI H3K9me and 5meC levels through a distinct mechanism from the known role of dicer-dependent sRNAs in guiding the DRM2 cytosine MTase because the PAI genes maintain H3K9me and 5meC at levels similar to wild type in a drm2 mutant. Our results support a new role for sRNAs in plants to prevent transcription-coupled loss of H3K9me. PMID:22046144

  9. COUPLING

    DOEpatents

    Frisch, E.; Johnson, C.G.

    1962-05-15

    A detachable coupling arrangement is described which provides for varying the length of the handle of a tool used in relatively narrow channels. The arrangement consists of mating the key and keyhole formations in the cooperating handle sections. (AEC)

  10. Critical coupling and coherent perfect absorption for ranges of energies due to a complex gain and loss symmetric system

    SciTech Connect

    Hasan, Mohammad; Ghatak, Ananya; Mandal, Bhabani Prasad

    2014-05-15

    We consider a non-Hermitian medium with a gain and loss symmetric, exponentially damped potential distribution to demonstrate different scattering features analytically. The condition for critical coupling (CC) for unidirectional wave and coherent perfect absorption (CPA) for bidirectional waves are obtained analytically for this system. The energy points at which total absorption occurs are shown to be the spectral singular points for the time reversed system. The possible energies at which CC occurs for left and right incidence are different. We further obtain periodic intervals with increasing periodicity of energy for CC and CPA to occur in this system. -- Highlights: •Energy ranges for CC and CPA are obtained explicitly for complex WS potential. •Analytical conditions for CC and CPA for PT symmetric WS potential are obtained. •Conditions for left and right CC are shown to be different. •Conditions for CC and CPA are shown to be that of SS for the time reversed system. •Our model shows the great flexibility of frequencies for CC and CPA.

  11. Equivalent circuit modeling of losses and dispersion in single and coupled lines for microwave and millimeter-wave integrated circuits

    NASA Astrophysics Data System (ADS)

    Tripathi, Vijai K.; Hill, Achim

    1988-02-01

    Losses and dispersion in open inhomogeneous guided-wave structures such as microstrips and other planar structures at microwave and millimeter-wave frequencies and in MMICs (monolithic microwave integrated circuits) have been modeled with circuits consisting of ideal lumped elements and lossless TEM (transverse electromagnetic) lines. It is shown that, given a propagation structure for which numerical techniques to compute the propagation characteristics are available, an equivalent circuit whose terminal frequency and time-domain properties are the same as the structure can be synthesized. This is accomplished by equating the network functions of the given single or coupled line multiport with that of the model and extracting all the parameters of the equivalent circuit model by using standard parameters identification procedures. This model is valid over a desired frequency range and can be used to help design both analog and digital circuits consisting of these structures and other active and passive elements utilizing standard CAD (computer-aided design) programs. To validate the accuracy and usefulness of the models, results for a mismatched 50-ohm line in alumina and a high-impedance MMIC line stub are included.

  12. Highly selective etching of silicon nitride to physical-vapor-deposited a-C mask in dual-frequency capacitively coupled CH{sub 2}F{sub 2}/H{sub 2} plasmas

    SciTech Connect

    Kim, J. S.; Kwon, B. S.; Heo, W.; Jung, C. R.; Park, J. S.; Shon, J. W.; Lee, N.-E.

    2010-01-15

    A multilevel resist (MLR) structure can be fabricated based on a very thin amorphous carbon (a-C) layer ( congruent with 80 nm) and Si{sub 3}N{sub 4} hard-mask layer ( congruent with 300 nm). The authors investigated the selective etching of the Si{sub 3}N{sub 4} layer using a physical-vapor-deposited (PVD) a-C mask in a dual-frequency superimposed capacitively coupled plasma etcher by varying the process parameters in the CH{sub 2}F{sub 2}/H{sub 2}/Ar plasmas, viz., the etch gas flow ratio, high-frequency source power (P{sub HF}), and low-frequency source power (P{sub LF}). They found that under certain etch conditions they obtain infinitely high etch selectivities of the Si{sub 3}N{sub 4} layers to the PVD a-C on both the blanket and patterned wafers. The etch gas flow ratio played a critical role in determining the process window for infinitely high Si{sub 3}N{sub 4}/PVD a-C etch selectivity because of the change in the degree of polymerization. The etch results of a patterned ArF photoresisit/bottom antireflective coating/SiO{sub x}/PVD a-C/Si{sub 3}N{sub 4} MLR structure supported the idea of using a very thin PVD a-C layer as an etch-mask layer for the Si{sub 3}N{sub 4} hard-mask pattern with a pattern width of congruent with 80 nm and high aspect ratio of congruent with 5.

  13. Inductively coupled plasma etching of GaAs low loss waveguides for a traveling waveguide polarization converter, using chlorine chemistry

    NASA Astrophysics Data System (ADS)

    Lu, J.; Meng, X.; Springthorpe, A. J.; Shepherd, F. R.; Poirier, M.

    2004-05-01

    A traveling waveguide polarization converter [M. Poirier et al.] has been developed, which involves long, low loss, weakly confined waveguides etched in GaAs (epitaxially grown by molecular beam epitaxy), with electroplated ``T electrodes'' distributed along the etched floor adjacent to the ridge walls, and airbridge interconnect metallization. This article describes the development of the waveguide fabrication, based on inductively coupled plasma (ICP) etching of GaAs using Cl2 chemistry; the special processes required to fabricate the electrodes and metallization [X. Meng et al.], and the device characteristics [M. Poirier et al.], are described elsewhere. The required waveguide has dimensions nominally 4 μm wide and 2.1 μm deep, with dimensional tolerances ~0.1 μm across the wafer and wafer to wafer. A vertical etch profile with very smooth sidewalls and floors is required to enable the plated metal electrodes to be fabricated within 0.1 μm of the ridge. The ridges were fabricated using Cl2 ICP etching and a photoresist mask patterned with an I-line stepper; He backside cooling, combined with an electrostatic chuck, was employed to ensure good heat transfer to prevent resist reticulation. The experimental results showed that the ridge profile is very sensitive to ICP power and platen rf power. High ICP power and low platen power tend to result in more isotropic etching, whereas increasing platen power increases the photoresist etch rate, which causes rougher ridge sidewalls. No strong dependence of GaAs etch rate and ridge profile were observed with small changes in process temperature (chuck temperature). However, when the chuck temperature was decreased from 25 to 0 °C, etch uniformity across a 3 in. wafer improved from 6% to 3%. Photoresist and polymer residues present after the ICP etch were removed using a combination of wet and dry processes. .

  14. Effect of Coupling between Fundamental and Cladding Modes on Bending Losses in Single-Polarization Single-Mode Photonic Crystal Fiber

    NASA Astrophysics Data System (ADS)

    Balvedi, Gláucia C.; Franco, Marcos A. R.

    2008-10-01

    In this paper we study the effect of bending on the performance of a single-polarization single-mode (SPSM) photonic crystal fiber previously reported in the literature. The optical fiber consists of a photonic crystal fiber with hexagonal lattice of circular air-holes with an elliptical core formed by eight enlarged holes surrounding the central region of the fiber. Numerical analysis based on full-vector finite element method (VFEM) with a cylindrical perfectly matched layer (PML) was applied to evaluate the bending loss and the confinement loss of the fiber. For the straight fiber only the fundamental slow axis mode (x-polarization) exist because of the very high confinement loss of the fundamental fast axis mode (y-polarization). However, for the bent fiber the fast axis mode and the slow axis mode couple with the gallery of the cladding modes. These coupling prevent the fast axis mode to reach the cutoff. As a consequence, the bending loss curve as a function of the wavelength presents oscillations related with these coupled modes. Our simulations demonstrate that the analyzed fiber does not maintain its single-polarization single-mode characteristics when it is bent with a small curvature radius of 10 mm. However, for a small wavelength range (1.50 μm to 1.53 μm) the fundamental slow axis mode presents values of bending loss lower then 0.1 dB/km while the fast axis mode reach losses of about 150 dB/km, what can be useful for some application.

  15. Low-loss coupling between two single-mode optical fibers with different mode-field diameters using a graded-index multimode optical fiber.

    PubMed

    Mafi, Arash; Hofmann, Peter; Salvin, Clémence Jollivet; Schülzgen, Axel

    2011-09-15

    We present a method for ultra-low-loss coupling between two single-mode optical fibers with different mode-field diameters using multimode interference in a graded-index multimode optical fiber. We perform a detailed analysis of the interference effects and show that the graded-index fiber can also be used as a beam expander or condenser. The results are important for devices in which optical fibers with different mode-field diameters are coupled in series, such as in ultra-short-pulse fiber ring lasers, or in optical fiber communication links. PMID:21931402

  16. A novel experimental setup for energy loss and charge state measurements in dense moderately coupled plasma using laser-heated hohlraum targets

    NASA Astrophysics Data System (ADS)

    Ortner, A.; Schumacher, D.; Cayzac, W.; Frank, A.; Basko, M. M.; Bedacht, S.; Blazevic, A.; Faik, S.; Kraus, D.; Rienecker, T.; Schaumann, G.; Tauschwitz, An.; Wagner, F.; Roth, M.

    2016-03-01

    We report on a new experimental setup for ion energy loss measurements in dense moderately coupled plasma which has recently been developed and tested at GSI Darmstadt. A partially ionized, moderately coupled carbon plasma (ne ≤ 0.8• 1022 cm-3, Te = 15 eV, z = 2.5, Γ = 0.5) is generated by volumetrical heating of two thin carbon foils with soft X-rays. This plasma is then probed by a bunched heavy ion beam. For that purpose, a special double gold hohlraum target of sub-millimeter size has been developed which efficiently converts intense laser light into thermal radiation and guarantees a gold-free interaction path for the ion beam traversing the carbon plasma. This setup allows to do precise energy loss measurements in non-ideal plasma at the level of 10 percent solid-state density.

  17. Energy saving in ac generators

    NASA Technical Reports Server (NTRS)

    Nola, F. J.

    1980-01-01

    Circuit cuts no-load losses, without sacrificing full-load power. Phase-contro circuit includes gate-controlled semiconductor switch that cuts off applied voltage for most of ac cycle if generator idling. Switch "on" time increases when generator is in operation.

  18. Multi-scale gyrokinetic simulation of tokamak plasmas: enhanced heat loss due to cross-scale coupling of plasma turbulence

    NASA Astrophysics Data System (ADS)

    Howard, N. T.; Holland, C.; White, A. E.; Greenwald, M.; Candy, J.

    2016-01-01

    The transport of heat in laboratory and astrophysical plasmas is dominated by the complex nonlinear dynamics of plasma turbulence. In magnetically confined plasmas used for fusion energy research, turbulence is responsible for cross-field transport that limits the performance of tokamak reactors. We report a set of novel gyrokinetic simulations that capture ion and electron-scale turbulence simultaneously, revealing the dynamics of cross-scale energy transfer and zonal flow modification that give rise to heat losses. Multi-scale simulations are required to match experimental ion and electron heat fluxes and electron profile stiffness, establishing the applicability of the newly discovered physics to experiment. Importantly, these results provide a likely explanation for the loss of electron heat from tokamak plasmas, the ‘great unsolved problem’ (Bachelor et al (2007 Plasma Sci. Technol. 9 312-87)) in plasma turbulence and the projected dominant loss channel in ITER.

  19. Characteristics of ? multifilamentary wires for a.c. use developed by the bronze process using diffusion barrier techniques

    NASA Astrophysics Data System (ADS)

    Miura, Osuke; Matsumoto, Kaname; Tanaka, Yasuzo; Uno, Naoki

    1996-03-01

    0953-2048/9/3/015/img7 multifilamentary superconducting wires for a.c. use were developed by the bronze method using Cu diffusion barrier techniques. To reduce a.c. losses, the filament diameter was designed to be less than 0953-2048/9/3/015/img8 and the final resistivity of the bronze matrix was increased using a Cu alloy diffusion barrier with the addition of Si and Mn elements around the filaments. As a result, interfilamentary proximity coupling could be prevented until a filament spacing of 0953-2048/9/3/015/img9 and hysteresis losses for the wires reached lower values, from 0953-2048/9/3/015/img10 to 0953-2048/9/3/015/img11 at a magnetic field amplitude of 0.5 T under controlled reaction heat treatment. The perpendicular resistivity of the matrix between the filaments estimated from the coupling loss was about 0953-2048/9/3/015/img12, which was considerably less than the resistivity value of the matrix estimated after the reaction. This was thought to be due to an extreme reduction in Sn concentration between the filaments. Furthermore, a small a.c. coil was fabricated by winding a stranded cable fabricated in this way. The a.c. loss of the coil at 50 Hz in a central magnetic field of 0.5 T was 0953-2048/9/3/015/img13 and the a.c. quench current at 50 Hz was 195 A, which is about 10% lower than the critical current on the load line. This degradation was due to the temperature rise in the cable caused by a.c. loss.

  20. Ubiquitylation by Trim32 causes coupled loss of desmin, Z-bands, and thin filaments in muscle atrophy.

    PubMed

    Cohen, Shenhav; Zhai, Bo; Gygi, Steven P; Goldberg, Alfred L

    2012-08-20

    During muscle atrophy, myofibrillar proteins are degraded in an ordered process in which MuRF1 catalyzes ubiquitylation of thick filament components (Cohen et al. 2009. J. Cell Biol. http://dx.doi.org/10.1083/jcb.200901052). Here, we show that another ubiquitin ligase, Trim32, ubiquitylates thin filament (actin, tropomyosin, troponins) and Z-band (α-actinin) components and promotes their degradation. Down-regulation of Trim32 during fasting reduced fiber atrophy and the rapid loss of thin filaments. Desmin filaments were proposed to maintain the integrity of thin filaments. Accordingly, we find that the rapid destruction of thin filament proteins upon fasting was accompanied by increased phosphorylation of desmin filaments, which promoted desmin ubiquitylation by Trim32 and degradation. Reducing Trim32 levels prevented the loss of both desmin and thin filament proteins. Furthermore, overexpression of an inhibitor of desmin polymerization induced disassembly of desmin filaments and destruction of thin filament components. Thus, during fasting, desmin phosphorylation increases and enhances Trim32-mediated degradation of the desmin cytoskeleton, which appears to facilitate the breakdown of Z-bands and thin filaments. PMID:22908310

  1. Measuring Inductive-Heating Coupling Coefficients and Thermal Loss Characteristics as a Function of Crucible Geometry and Material Selection

    NASA Astrophysics Data System (ADS)

    Gomes, Jay

    A power measurement system has been designed for an ultra-high temperature inductively heated molten oxide electrolysis (MOE) reactor. The work presented in this research contributes to three different aspects of the induction heated MOE reactor facility: mathematical modeling of coil-to-workpiece power transfer, numerical modeling of heat transfer within the reactor, and experiments to measure the total hemispherical emittance of potential crucible materials. Facility-specific coupling coefficients for various samples have been experimentally determined for the MOE reactor facility. An analytical model coupling the predicted power input with heat transfer software was developed using COMSOL Multiphysics, and validated with experimental measurements of the steady state temperature gradient inside the reactor. These models were used to support the design of an experiment to measure the total hemispherical emissivity (epsilon) of conductive samples using a transient calorimetric technique. Results of epsilon are presented over a wide range of temperatures for copper, nickel, graphite and molybdenum. Furthermore, an investigation into optimizing the reactor system for heating will be discussed.

  2. Study on the mechanism of a charge-coupled device detector irradiated by millisecond pulse laser under functional loss.

    PubMed

    Li, Mingxin; Jin, Guangyong; Tan, Yong; Guo, Ming; Zhu, Pengbo

    2016-02-20

    The damage mechanism of a CCD detector was studied by building an experimental system containing a millisecond pulse laser irradiating a CCD detector. The experimental results show that the damage on the CCD detector was mainly thermal damage, along with mechanical damage. A melting phenomenon was caused by the thermal damage, so that a crater was observed on the surface of the CCD detector. Caused by melting of the polysilicon electrodes and a temperature rise in the silicon dioxide, the shift register impedance values were sharply reduced. Most of the substrate clock signals were broken and disappeared due to melting of channels in the silicon substrate layer, which caused a functional loss for the CCD detector. The mechanical damage on the melting edge of the CCD detector created heave; the temperature gradient caused this damage. In this paper, the decrease in vertical shift register impedance values was consistent with previous test results. PMID:26906576

  3. COUPLING THE SOLAR DYNAMO AND THE CORONA: WIND PROPERTIES, MASS, AND MOMENTUM LOSSES DURING AN ACTIVITY CYCLE

    SciTech Connect

    Pinto, Rui F.; Brun, Allan Sacha; Grappin, Roland

    2011-08-20

    We study the connections between the Sun's convection zone and the evolution of the solar wind and corona. We let the magnetic fields generated by a 2.5-dimensional (2.5D) axisymmetric kinematic dynamo code (STELEM) evolve in a 2.5D axisymmetric coronal isothermal magnetohydrodynamic code (DIP). The computations cover an 11 year activity cycle. The solar wind's asymptotic velocity varies in latitude and in time in good agreement with the available observations. The magnetic polarity reversal happens at different paces at different coronal heights. Overall the Sun's mass-loss rate, momentum flux, and magnetic braking torque vary considerably throughout the cycle. This cyclic modulation is determined by the latitudinal distribution of the sources of open flux and solar wind and the geometry of the Alfven surface. Wind sources and braking torque application zones also vary accordingly.

  4. Low loss coupling and splicing of standard single mode fibers with all-solid soft-glass microstructured fibers for supercontinuum generation

    NASA Astrophysics Data System (ADS)

    Murawski, M.; Stepniewski, G.; Tenderenda, T.; Napierała, M.; Hołdyński, Z.; Szostkiewicz, L.; Slowikowski, M.; Szymanski, M.; Ostrowski, L.; Jaroszewicz, L. R.; Buczyński, R.; Nasiłowski, T.

    2014-03-01

    In this work we would like to present the results of low loss coupling of a novel soft glass fiber for super continuum generation with standard single mode fiber by a filament splicing method. For our experiment we used an all solid soft glass microstructured fiber (MSF) made from a composition of F2 lead-silicate glass and NC21 borosilicate glass. The structure and material properties of the fiber were optimized to achieve all normal dispersion (ND) flattened around 1560 nm, which offers two general advantages for supercontinuum generation. The ND supercontinuum avoids soliton dynamics, hence it is less sensitive to pump laser shot noise and has larger degree of coherence than supercontinuum in the anomalous dispersion range. Furthermore flattening around 1560 nm indicates optimal supercontinuum pump wavelength, which is readily available from erbium doped femtosecond fiber lasers. Using Vytran splicing station (GPX3400) we were able to achieve repeatable splice loss between a standard fused-silica single mode fiber (SMF28) and the low-melting-temperature soft glass MSF as low as 2.12 dB @1310 nm and 1.94 dB @ 1550 nm. The developed very low loss splicing technology together with the above mentioned all solid soft glass MSF advantages give very promising perspectives for commercial applications.

  5. Development of 100kVA AC superconducting coil using NbTi cables with a CuSi alloy matrix

    SciTech Connect

    Kasahara, H.; Akita, S.; Torii, S.; Sugimoto, M.; Matsumoto, K.; Tanaka, Y.; Tachikawa, K.

    1996-07-01

    For implementation of AC superconducting equipment, it is imperative to develop low loss cables having highly stable characteristics. Here, newly developed NbTi superconducting cables using a CuSi alloy matrix are of low loss and are very promising as cables for practical application. However, since the CuSi alloy is a new material as a matrix for NbTi superconducting cables, many unknown factors as regards to optimum conditions for the manufacture of long cables, as well as superconducting characteristics are involved. For this new superconducting cable, a long strand (km class) was manufactured as a step for practical application, and a primary twisted cable was fabricated. Using this cable, a coil of the 100kVA class was fabricated for trial, and its performance characteristic with transport current was evaluated. This coil had no training phenomenon and had high stabilities. Furthermore, it permitted full AC current transmission of up to DCIc. Upon analysis of the coil loss, the hysteresis loss was smaller than coupling loss, and there was little increase of loss due to the current flow to the coil. consequently, by using CuSi alloy matrix superconducting cables, it was possible to provide an AC coil of low loss and high stability, and the present cable was found to be promising as a new AC superconducting cable in the future.

  6. Chromosomal aberration leads to recurrent pregnancy loss and partial trisomy of 5p12-15.3 in the offspring: report of a Syrian couple and review of the literature .

    PubMed

    Al-Achkar, Walid; Moassass, Faten; Al-Ablog, Ayman; Liehr, Thomas; Fan, Xiaobo; Wafa, Abdulsamad

    2015-03-01

    Here we describe a Syrian couple having recurrent pregnancy loss in the first trimester, fetal malformations, and/or neonatal death. The father had a balanced chromosomal translocation t(5;15), an sY125 microdeletion of locus b in the azoospermia factor (AZF) gene, and an MTHFR C677T homozygous polymorphism with normal phenotype. Interestingly, his healthy wife had another MTHFR A1298C homozygous polymorphism. The couple experienced two pregnancy losses and had two stillborn children with severe malformations due to partial trisomy of the short arm of chromosome 5. The couple does not have any living offspring after 10 years of marriage. PMID:25898552

  7. Energy Loss of Solar p Modes due to the Excitation of Magnetic Sausage Tube Waves: Importance of Coupling the Upper Atmosphere

    NASA Astrophysics Data System (ADS)

    Gascoyne, A.; Jain, R.; Hindman, B. W.

    2014-07-01

    We consider damping and absorption of solar p modes due to their energy loss to magnetic tube waves that can freely carry energy out of the acoustic cavity. The coupling of p modes and sausage tube waves is studied in a model atmosphere composed of a polytropic interior above which lies an isothermal upper atmosphere. The sausage tube waves, excited by p modes, propagate along a magnetic fibril which is assumed to be a vertically aligned, stratified, thin magnetic flux tube. The deficit of p-mode energy is quantified through the damping rate, Γ, and absorption coefficient, α. The variation of Γ and α as a function of frequency and the tube's plasma properties is studied in detail. Previous similar studies have considered only a subphotospheric layer, modeled as a polytrope that has been truncated at the photosphere. Such studies have found that the resulting energy loss by the p modes is very sensitive to the upper boundary condition, which, due to the lack of an upper atmosphere, have been imposed in a somewhat ad hoc manner. The model presented here avoids such problems by using an isothermal layer to model the overlying atmosphere (chromosphere, and, consequently, allows us to analyze the propagation of p-mode-driven sausage waves above the photosphere. In this paper, we restrict our attention to frequencies below the acoustic cut off frequency. We demonstrate the importance of coupling all waves (acoustic, magnetic) in the subsurface solar atmosphere with the overlying atmosphere in order to accurately model the interaction of solar f and p modes with sausage tube waves. In calculating the absorption and damping of p modes, we find that for low frequencies, below ≈3.5 mHz, the isothermal atmosphere, for the two-region model, behaves like a stress-free boundary condition applied at the interface (z = -z 0).

  8. Energy loss of solar p modes due to the excitation of magnetic sausage tube waves: Importance of coupling the upper atmosphere

    SciTech Connect

    Gascoyne, A.; Jain, R.; Hindman, B. W. E-mail: r.jain@sheffield.ac.uk

    2014-07-10

    We consider damping and absorption of solar p modes due to their energy loss to magnetic tube waves that can freely carry energy out of the acoustic cavity. The coupling of p modes and sausage tube waves is studied in a model atmosphere composed of a polytropic interior above which lies an isothermal upper atmosphere. The sausage tube waves, excited by p modes, propagate along a magnetic fibril which is assumed to be a vertically aligned, stratified, thin magnetic flux tube. The deficit of p-mode energy is quantified through the damping rate, Γ, and absorption coefficient, α. The variation of Γ and α as a function of frequency and the tube's plasma properties is studied in detail. Previous similar studies have considered only a subphotospheric layer, modeled as a polytrope that has been truncated at the photosphere. Such studies have found that the resulting energy loss by the p modes is very sensitive to the upper boundary condition, which, due to the lack of an upper atmosphere, have been imposed in a somewhat ad hoc manner. The model presented here avoids such problems by using an isothermal layer to model the overlying atmosphere (chromosphere, and, consequently, allows us to analyze the propagation of p-mode-driven sausage waves above the photosphere. In this paper, we restrict our attention to frequencies below the acoustic cut off frequency. We demonstrate the importance of coupling all waves (acoustic, magnetic) in the subsurface solar atmosphere with the overlying atmosphere in order to accurately model the interaction of solar f and p modes with sausage tube waves. In calculating the absorption and damping of p modes, we find that for low frequencies, below ≈3.5 mHz, the isothermal atmosphere, for the two-region model, behaves like a stress-free boundary condition applied at the interface (z = –z{sub 0}).

  9. Dyes and Redox Couples with Matched Energy Levels: Elimination of the Dye-Regeneration Energy Loss in Dye-Sensitized Solar Cells.

    PubMed

    Jiang, Dianlu; Darabedian, Narek; Ghazarian, Sevak; Hao, Yuanqiang; Zhgamadze, Maxim; Majaryan, Natalie; Shen, Rujuan; Zhou, Feimeng

    2015-11-16

    In dye-sensitized solar cells (DSSCs), a significant dye-regeneration force (ΔG(reg)(0)≥0.5 eV) is usually required for effective dye regeneration, which results in a major energy loss and limits the energy-conversion efficiency of state-of-art DSSCs. We demonstrate that when dye molecules and redox couples that possess similar conjugated ligands are used, efficient dye regeneration occurs with zero or close-to-zero driving force. By using Ru(dcbpy)(bpy)2(2+) as the dye and Ru(bpy)2(MeIm)2(3+//2+) as the redox couple, a short-circuit current (J(sc)) of 4 mA cm(-2) and an open-circuit voltage (V(oc)) of 0.9 V were obtained with a ΔG(reg)(0) of 0.07 eV. The same was observed for the N3 dye and Ru(bpy)2(SCN)2(1+/0) (ΔG(reg)(0)=0.0 eV), which produced an J(sc) of 2.5 mA cm(-2) and V(oc) of 0.6 V. Charge recombination occurs at pinholes, limiting the performance of the cells. This proof-of-concept study demonstrates that high V(oc) values can be attained by significantly curtailing the dye-regeneration force. PMID:26314383

  10. Level structure and reflection asymmetric shape in sup 223 Ac

    SciTech Connect

    Sheline, R.K.; Liang, C.F.; Paris, P. )

    1990-07-20

    Mass separated sources of {sup 227}Pa (separated as PaF{sub 4}{sup +} ions) were used to study the level structure of {sup 223}Ac following alpha decay. The levels in {sup 223}Ac are interpreted as K = 5/2{sup {plus minus}} parity doublet bands which occur naturally in reflection asymmetric models and the multiphonon octupole model. The anomalous structure of the K = 3/2{sup {minus}} band is explained in terms of Coriolis coupling. The low lying parity doublet bands in {sup 223}Ac, {sup 225}Ac, and {sup 227}Ac are compared and contrasted.

  11. UPS with input commutation between ac and dc sources of power

    SciTech Connect

    Severinsky, A.J.

    1993-08-31

    An uninterruptible power supply is described, said power supply comprising: AC input terminal means for receiving a first AC voltage from an AC power source; DC input terminal means for receiving a first DC voltage from a DC power source; AC output terminal means for connecting to a load; converter means for converting said first AC voltage to a second DC voltage across electrical charge storage means coupled to said converter means, said second DC voltage being larger than the maximum peak voltage of said first AC voltage and said first DC voltage; switching means coupled to said AC power source and said DC power source for selectively connecting said AC power source or said DC power source to said converter means; inverter means coupled to said electrical charge storage means for receiving said second DC voltage and inverting said second DC voltage to a second AC voltage, said second AC voltage being coupled to said AC output terminal means; and control means coupled to said switching means for controlling the operation of said switching means, said control means operating said switching means to connect said AC power source to said converter means only when said first AC voltage is within a predetermined range and operating to connect said DC power source to said converter means when said first AC voltage is outside of said range.

  12. ACS Quicklook PDF products

    NASA Astrophysics Data System (ADS)

    Suchkov, Anatoly

    1999-12-01

    This report details the features of the ACS quicklook PDF products produced by the HST data pipeline. The requirements closely follow the design of paper products recommended by the Data Quality Committee, with appropriate changes required to fully support ACS.

  13. ALTERNATING CURRENT LOSSES IN AG-SHEATHED BSCCO (2212 AND 2223) TAPES AND WIRES AND YBCO (123) COATED CONDUCTORS

    SciTech Connect

    Dr. John S. Hurley

    2000-01-01

    In this study, we focus on the examination of ac losses in conductors utilizing Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O [BSCCO (2223)] high TC superconductors (HTS). In addition, we seek to assist other facilities such as the University of Wisconsin-Madison Applied Superconductivity Center (UW-ASC), Brookhaven National Laboratory, and other DoE facilities investigating the use of HTS in electric power applications (e.g., generators, motors, and transformers). To accomplish this we will develop an ac losses capability at Clark Atlanta University to complement the established ac losses efforts at Brookhaven National Laboratory (BSCCO) on BSCCO/Ag and various material characterization efforts taking place at the UW-ASC. Our goal is through this effort to gain a greater understanding of the effects on ac losses due to parameters such as ac/dc current, J{sub c}, tape geometry, voltage tap placement, field orientation, material anisotropy, surface irregularities, percolations and filament coupling effects. As a result, we expect to better understand how to minimize ac losses in applications requiring real or practical conductors. HTS conductors based on BSCCO-2223 are now being routinely produced in industrial lengths of high quality. Vendors such as Southwire and ASC are producing multi-filamentary tapes in lengths of 6 km or more carrying critical current densities of up to 3 kA/cm**2 at 77 K. While this is approaching the level of performance where some large-scale applications are considered to be economically viable, a number of problems remain to be solved. The remaining issues include: rapid reduction in JC in magnetic fields; and power dissipation due to varying magnetic fields or currents (ac losses).

  14. The Free Fatty Acid Receptor G Protein-coupled Receptor 40 (GPR40) Protects from Bone Loss through Inhibition of Osteoclast Differentiation*

    PubMed Central

    Wauquier, Fabien; Philippe, Claire; Léotoing, Laurent; Mercier, Sylvie; Davicco, Marie-Jeanne; Lebecque, Patrice; Guicheux, Jérôme; Pilet, Paul; Miot-Noirault, Elisabeth; Poitout, Vincent; Alquier, Thierry; Coxam, Véronique; Wittrant, Yohann

    2013-01-01

    The mechanisms linking fat intake to bone loss remain unclear. By demonstrating the expression of the free fatty acid receptor G-coupled protein receptor 40 (GPR40) in bone cells, we hypothesized that this receptor may play a role in mediating the effects of fatty acids on bone remodeling. Using micro-CT analysis, we showed that GPR40−/− mice exhibit osteoporotic features suggesting a positive role of GPR40 on bone density. In primary cultures of bone marrow, we showed that GW9508, a GRP40 agonist, abolished bone-resorbing cell differentiation. This alteration of the receptor activator of NF-κB ligand (RANKL)-induced osteoclast differentiation occurred via the inhibition of the nuclear factor κB (NF-κB) signaling pathway as demonstrated by decrease in gene reporter activity, inhibitor of κB kinase (IKKα/β) activation, inhibitor of κB (IkBα) phosphorylation, and nuclear factor of activated T cells 1 (NFATc1) expression. The GPR40-dependent effect of GW9508 was confirmed using shRNA interference in osteoclast precursors and GPR40−/− primary cell cultures. In addition, in vivo administration of GW9508 counteracted ovariectomy-induced bone loss in wild-type but not GPR40−/− mice, enlightening the obligatory role of the GPR40 receptor. Then, in a context of growing prevalence of metabolic and age-related bone disorders, our results demonstrate for the first time in translational approaches that GPR40 is a relevant target for the design of new nutritional and therapeutic strategies to counter bone complications. PMID:23335512

  15. Energy loss of a nonaccelerating quark moving through a strongly coupled N =4 super Yang-Mills vacuum or plasma in strong magnetic field

    NASA Astrophysics Data System (ADS)

    Mamo, Kiminad A.

    2016-08-01

    Using AdS /CFT correspondence, we find that a massless quark moving at the speed of light v =1 , in arbitrary direction, through a strongly coupled N =4 super Yang-Mills (SYM) vacuum at T =0 , in the presence of strong magnetic field B , loses its energy at a rate linearly dependent on B , i.e., d/E d t =-√{λ/} 6 π B . We also show that a heavy quark of mass M ≠0 moving at near the speed of light v2=v*2=1 -4/π2T2 B ≃1 , in arbitrary direction, through a strongly coupled N =4 SYM plasma at finite temperature T ≠0 , in the presence of strong magnetic field B ≫T2, loses its energy at a rate linearly dependent on B , i.e., d/E d t =-√{λ/}6 π B v*2≃-√{λ/}6 π B . Moreover, we argue that, in the strong magnetic field B ≫T2 (IR) regime, N =4 SYM and adjoint QCD theories (when the adjoint QCD theory has four flavors of Weyl fermions and is at its conformal IR fixed point λ =λ*) have the same microscopic degrees of freedom (i.e., gluons and lowest Landau levels of Weyl fermions) even though they have quite different microscopic degrees of freedom in the UV when we consider higher Landau levels. Therefore, in the strong magnetic field B ≫T2 (IR) regime, the thermodynamic and hydrodynamic properties of N =4 SYM and adjoint QCD plasmas, as well as the rates of energy loss of a quark moving through the plasmas, should be the same.

  16. Diffuse light reflectance signals as potential indicators of loss of viability in brain tissue due to hypoxia: charge-coupled-device-based imaging and fiber-based measurement

    NASA Astrophysics Data System (ADS)

    Kawauchi, Satoko; Nishidate, Izumi; Uozumi, Yoichi; Nawashiro, Hiroshi; Ashida, Hiroshi; Sato, Shunichi

    2013-01-01

    Brain tissue is highly vulnerable to ischemia/hypoxia, and real-time monitoring of its viability is important. By fiber-based measurements for rat brain, we previously observed a unique triphasic reflectance change (TRC) after a certain period of time after hypoxia. After TRC, rats could not be rescued, suggesting that TRC can be used as an indicator of loss of brain tissue viability. In this study, we investigated this diffuse-reflectance change due to hypoxia in three parts. First, we developed and validated a theoretical method to quantify changes in the absorption and reduced scattering coefficients involved in TRC. Second, we performed charge-coupled-device-based reflectance imaging of the rat brain during hypoxia followed by reoxygenation to examine spatiotemporal characteristics of the reflectance and its correlation with reversibility of brain tissue damage. Third, we made simultaneous imaging and fiber-based measurement of the reflectance for the rat to compare signals obtained by these two modalities. We observed a nontriphasic reflectance change by the imaging, and it was associated with brain tissue viability. We found that TRC measured by the fibers preceded the reflectance-signal change captured by the imaging. This time difference is attributable to the different observation depths in the brain with these two methods.

  17. Loss of the repressor REST in uterine fibroids promotes aberrant G protein-coupled receptor 10 expression and activates mammalian target of rapamycin pathway

    PubMed Central

    Varghese, Binny V.; Koohestani, Faezeh; McWilliams, Michelle; Colvin, Arlene; Gunewardena, Sumedha; Kinsey, William H.; Nowak, Romana A.; Nothnick, Warren B.; Chennathukuzhi, Vargheese M.

    2013-01-01

    Uterine fibroids (leiomyomas) are the most common tumors of the female reproductive tract, occurring in up to 77% of reproductive-aged women, yet molecular pathogenesis remains poorly understood. A role for atypically activated mammalian target of rapamycin (mTOR) pathway in the pathogenesis of uterine fibroids has been suggested in several studies. We identified that G protein-coupled receptor 10 [GPR10, a putative signaling protein upstream of the phosphoinositide 3-kinase–protein kinase B/AKT–mammalian target of rapamycin (PI3K/AKT–mTOR) pathway] is aberrantly expressed in uterine fibroids. The activation of GPR10 by its cognate ligand, prolactin releasing peptide, promotes PI3K–AKT–mTOR pathways and cell proliferation specifically in cultured primary leiomyoma cells. Additionally, we report that RE1 suppressing transcription factor/neuron-restrictive silencing factor (REST/NRSF), a known tumor suppressor, transcriptionally represses GPR10 in the normal myometrium, and that the loss of REST in fibroids permits GPR10 expression. Importantly, mice overexpressing human GPR10 in the myometrium develop myometrial hyperplasia with excessive extracellular matrix deposition, a hallmark of uterine fibroids. We demonstrate previously unrecognized roles for GPR10 and its upstream regulator REST in the pathogenesis of uterine fibroids. Importantly, we report a unique genetically modified mouse model for a gene that is misexpressed in uterine fibroids. PMID:23284171

  18. Quantitative imaging analysis and investigation of transmission loss in PbF2 crystals by laser ablation-inductively coupled plasma-mass spectrometry method.

    PubMed

    Zhang, Guoxia; Wang, Zheng; Li, Qing; Zhou, Hui; Zhu, Yan; Du, Yiping

    2016-07-01

    We developed a procedure for preparing matrix-matched calibration standards for the quantitative imaging of multiple trace elements in PbF2 crystals by laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). In this facile approach, PbO powder was employed as the matrix with the addition of a series of standard solutions, followed by drying and tableting, for determining the concentrations of (24)Mg, (27)Al, (89)Y, (103)Rh, (133)Cs, (175)Lu and (209)Bi in transparent samples (with homogeneous element distribution). (206)Pb was chosen as the internal standard and the correlation coefficients of the calibration curves for all elements ranged from 0.9987 to 0.9999 after internal standard correction. The analysis showed good agreement with the results observed by established ICP-MS methods, following acid dissolution of the samples. Finally, the element distributions and transmission curves of a PbF2 sample with non-transparent and transparent sections were visualized. The distribution images, in conjunction with the transmission curves, suggested that the enrichment of Mg, Al, Rh, Cs, and Bi atoms in the non-transparent section of the sample could explain the loss in transmission observed for that section. PMID:27154704

  19. Diffuse light reflectance signals as potential indicators of loss of viability in brain tissue due to hypoxia: charge-coupled-device-based imaging and fiber-based measurement.

    PubMed

    Kawauchi, Satoko; Nishidate, Izumi; Uozumi, Yoichi; Nawashiro, Hiroshi; Ashida, Hiroshi; Sato, Shunichi

    2013-01-01

    Brain tissue is highly vulnerable to ischemia/hypoxia, and real-time monitoring of its viability is important. By fiber-based measurements for rat brain, we previously observed a unique triphasic reflectance change (TRC) after a certain period of time after hypoxia. After TRC, rats could not be rescued, suggesting that TRC can be used as an indicator of loss of brain tissue viability. In this study, we investigated this diffuse-reflectance change due to hypoxia in three parts. First, we developed and validated a theoretical method to quantify changes in the absorption and reduced scattering coefficients involved in TRC. Second, we performed charge-coupled-device-based reflectance imaging of the rat brain during hypoxia followed by reoxygenation to examine spatiotemporal characteristics of the reflectance and its correlation with reversibility of brain tissue damage. Third, we made simultaneous imaging and fiber-based measurement of the reflectance for the rat to compare signals obtained by these two modalities. We observed a nontriphasic reflectance change by the imaging, and it was associated with brain tissue viability. We found that TRC measured by the fibers preceded the reflectance-signal change captured by the imaging. This time difference is attributable to the different observation depths in the brain with these two methods. PMID:23291715

  20. Pregnancy loss.

    PubMed

    Robinson, Gail Erlick

    2014-01-01

    Women who lose desired pregnancies by miscarriage, stillbirth, or genetic termination are at risk of suffering from grief, anxiety, guilt and self-blame that may even present in subsequent pregnancies. It is important to find effective means of helping women deal with these losses. The approach to stillbirth has shifted from immediately removing the child from the mother to encouraging the parents to view and hold the baby. This approach has been questioned as possibly causing persistent anxiety and post-traumatic stress disorder. Women who miscarry are currently encouraged to find ways to memorialise the lost fetus. Couples who decide to terminate a pregnancy after discovering a defect may deal not only with sadness but also guilt. Immediate crisis intervention and follow-up care should be available, recognising that individual women may experience different reactions and their specific post-loss needs must be assessed. PMID:24047642

  1. Coupled 3D-neutronics / thermal-hydraulics analysis of an unprotected loss-of-flow accident for a 3600 MWth SFR core

    SciTech Connect

    Sun, K.; Chenu, A.; Mikityuk, K.; Krepel, J.; Chawla, R.

    2012-07-01

    The core behaviour of a large (3600 MWth) sodium-cooled fast reactor (SFR) is investigated in this paper with the use of a coupled TRACE/PARCS model. The SFR neutron spectrum is characterized by several performance advantages, but also leads to one dominating neutronics drawback - a positive sodium void reactivity. This implies a positive reactivity effect when sodium coolant is removed from the core. In order to evaluate such feedback in terms of the dynamics, a representative unprotected loss-of-flow (ULOF) transient, i.e. flow run-down without SCRAM in which sodium boiling occurs, is analyzed. Although analysis of a single transient cannot allow general conclusions to be drawn, it does allow better understanding of the underlying physics and can lead to proposals for improving the core response during such an accident. The starting point of this study is the reference core design considered in the framework of the Collaborative Project on the European Sodium Fast Reactor (CP-ESFR). To reduce the void effect, the core has been modified by introducing an upper sodium plenum (along with a boron layer) and by reducing the core height-to-diameter ratio. For the ULOF considered, a sharp increase in core power results in melting of the fuel in the case of the reference core. In the modified core, a large dryout leads to melting of the clad. It seems that, for the hypothetical event considered, fuel failure cannot be avoided with just improvement of the neutronics design; therefore, thermal-hydraulics optimization has been considered. An innovative assembly design is proposed to prevent sodium vapour blocking the fuel channel. This results in preventing a downward propagation of the sodium boiling to the core center, thus limiting it to the upper region. Such a void map introduces a negative coolant density reactivity feedback, which dominates the total reactivity change. As a result, the power level and the fuel temperature are effectively reduced, and a large dryout

  2. Hearing Loss

    MedlinePlus

    ... version of this page please turn Javascript on. Hearing Loss What is Hearing Loss? Hearing loss is a common problem caused by ... sec Click to watch this video Types of Hearing Loss Hearing loss comes in many forms. It can ...

  3. Low-Loss Coupling of Quantum Cascade Lasers into Hollow-Core Waveguides with Single-Mode Output in the 3.7-7.6 μm Spectral Range.

    PubMed

    Patimisco, Pietro; Sampaolo, Angelo; Mihai, Laura; Giglio, Marilena; Kriesel, Jason; Sporea, Dan; Scamarcio, Gaetano; Tittel, Frank K; Spagnolo, Vincenzo

    2016-01-01

    We demonstrated low-loss and single-mode laser beam delivery through hollow-core waveguides (HCWs) operating in the 3.7-7.6 μm spectral range. The employed HCWs have a circular cross section with a bore diameter of 200 μm and metallic/dielectric internal coatings deposited inside a glass capillary tube. The internal coatings have been produced to enhance the spectral response of the HCWs in the range 3.5-12 µm. We demonstrated Gaussian-like outputs throughout the 4.5-7.6 µm spectral range. A quasi single-mode output beam with only small beam distortions was achieved when the wavelength was reduced to 3.7 μm. With a 15-cm-long HCW and optimized coupling conditions, we measured coupling efficiencies of >88% and transmission losses of <1 dB in the investigated infrared spectral range. PMID:27089343

  4. Low-Loss Coupling of Quantum Cascade Lasers into Hollow-Core Waveguides with Single-Mode Output in the 3.7–7.6 μm Spectral Range

    PubMed Central

    Patimisco, Pietro; Sampaolo, Angelo; Mihai, Laura; Giglio, Marilena; Kriesel, Jason; Sporea, Dan; Scamarcio, Gaetano; Tittel, Frank K.; Spagnolo, Vincenzo

    2016-01-01

    We demonstrated low-loss and single-mode laser beam delivery through hollow-core waveguides (HCWs) operating in the 3.7–7.6 μm spectral range. The employed HCWs have a circular cross section with a bore diameter of 200 μm and metallic/dielectric internal coatings deposited inside a glass capillary tube. The internal coatings have been produced to enhance the spectral response of the HCWs in the range 3.5–12 µm. We demonstrated Gaussian-like outputs throughout the 4.5–7.6 µm spectral range. A quasi single-mode output beam with only small beam distortions was achieved when the wavelength was reduced to 3.7 μm. With a 15-cm-long HCW and optimized coupling conditions, we measured coupling efficiencies of >88% and transmission losses of <1 dB in the investigated infrared spectral range. PMID:27089343

  5. Microfabricated AC impedance sensor

    DOEpatents

    Krulevitch, Peter; Ackler, Harold D.; Becker, Frederick; Boser, Bernhard E.; Eldredge, Adam B.; Fuller, Christopher K.; Gascoyne, Peter R. C.; Hamilton, Julie K.; Swierkowski, Stefan P.; Wang, Xiao-Bo

    2002-01-01

    A microfabricated instrument for detecting and identifying cells and other particles based on alternating current (AC) impedance measurements. The microfabricated AC impedance sensor includes two critical elements: 1) a microfluidic chip, preferably of glass substrates, having at least one microchannel therein and with electrodes patterned on both substrates, and 2) electrical circuits that connect to the electrodes on the microfluidic chip and detect signals associated with particles traveling down the microchannels. These circuits enable multiple AC impedance measurements of individual particles at high throughput rates with sufficient resolution to identify different particle and cell types as appropriate for environmental detection and clinical diagnostic applications.

  6. DC coupled Doppler radar physiological monitor.

    PubMed

    Zhao, Xi; Song, Chenyan; Lubecke, Victor; Boric-Lubecke, Olga

    2011-01-01

    One of the challenges in Doppler radar systems for physiological monitoring is a large DC offset in baseband outputs. Typically, AC coupling is used to eliminate this DC offset. Since the physiological signals of interest include frequency content near DC, it is not desirable to simply use AC coupling on the radar outputs. While AC coupling effectively removes DC offset, it also introduces a large time delay and distortion. This paper presents the first DC coupled IQ demodulator printed circuit board (PCB) design and measurements. The DC coupling is achieved by using a mixer with high LO to RF port isolation, resulting in a very low radar DC offset on the order of mV. The DC coupled signals from the PCB radar system were successfully detected with significant LNA gain without saturation. Compared to the AC coupled results, the DC coupled results show great advantages of less signal distortion and more accurate rate estimation. PMID:22254704

  7. AC magnetohydrodynamic microfluidic switch

    SciTech Connect

    Lemoff, A V; Lee, A P

    2000-03-02

    A microfluidic switch has been demonstrated using an AC Magnetohydrodynamic (MHD) pumping mechanism in which the Lorentz force is used to pump an electrolytic solution. By integrating two AC MHD pumps into different arms of a Y-shaped fluidic circuit, flow can be switched between the two arms. This type of switch can be used to produce complex fluidic routing, which may have multiple applications in {micro}TAS.

  8. ACS Symposium Support

    SciTech Connect

    Kenneth D. Jordan

    2010-02-20

    The funds from this DOE grant were used to help cover the travel costs of five students and postdoctoral fellows who attended a symposium on 'Hydration: From Clusters to Aqueous Solutions' held at the Fall 2007 American Chemical Society Meeting in Boston, MA, August 19-23. The Symposium was sponsored by the Physical Chemistry Division, ACS. The technical program for the meeting is available at http://phys-acs.org/fall2007.html.

  9. NOX3 NADPH Oxidase Couples Transient Receptor Potential Vanilloid 1 to Signal Transducer and Activator of Transcription 1-Mediated Inflammation and Hearing Loss

    PubMed Central

    Mukherjea, Debashree; Jajoo, Sarvesh; Sheehan, Kelly; Kaur, Tejbeer; Sheth, Sandeep; Bunch, Jennifer; Perro, Christopher; Rybak, Leonard P.

    2011-01-01

    Abstract Transient receptor potential vanilloid 1 (TRPV1) is implicated in cisplatin ototoxicity. Activation of this channel by cisplatin increases reactive oxygen species generation, which contribute to loss of outer hair cells in the cochlea. Knockdown of TRPV1 by short interfering RNA protected against cisplatin ototoxicity. In this study, we examined the mechanism underlying TRPV1-mediated ototoxicity using cultured organ of Corti transformed cells (UB/OC-1) and rats. Trans-tympanic injections of capsaicin produced transient hearing loss within 24 h, which recovered by 72 h. In UB/OC-1 cells, capsaicin increased NOX3 NADPH oxidase activity and activation of signal transducer and activator of transcription 1 (STAT1). Intratympanic administration of capsaicin transiently increased STAT1 activity and expression of downstream proinflammatory molecules. Capsaicin produced a transient increase in CD14-positive inflammatory cells into the cochlea, which mimicked the temporal course of STAT1 activation but did not alter the expression of apoptotic genes or damage to outer hair cells. In addition, trans-tympanic administration of STAT1 short interfering RNA protected against capsaicin-induced hearing loss. These data suggest that activation of TRPV1 mediates temporary hearing loss by initiating an inflammatory process in the cochlea via activation of NOX3 and STAT1. Thus, these proteins represent reasonable targets for ameliorating hearing loss. Antioxid. Redox Signal. 14, 999–1010. PMID:20712533

  10. NOX3 NADPH oxidase couples transient receptor potential vanilloid 1 to signal transducer and activator of transcription 1-mediated inflammation and hearing loss.

    PubMed

    Mukherjea, Debashree; Jajoo, Sarvesh; Sheehan, Kelly; Kaur, Tejbeer; Sheth, Sandeep; Bunch, Jennifer; Perro, Christopher; Rybak, Leonard P; Ramkumar, Vickram

    2011-03-15

    Transient receptor potential vanilloid 1 (TRPV1) is implicated in cisplatin ototoxicity. Activation of this channel by cisplatin increases reactive oxygen species generation, which contribute to loss of outer hair cells in the cochlea. Knockdown of TRPV1 by short interfering RNA protected against cisplatin ototoxicity. In this study, we examined the mechanism underlying TRPV1-mediated ototoxicity using cultured organ of Corti transformed cells (UB/OC-1) and rats. Trans-tympanic injections of capsaicin produced transient hearing loss within 24 h, which recovered by 72 h. In UB/OC-1 cells, capsaicin increased NOX3 NADPH oxidase activity and activation of signal transducer and activator of transcription 1 (STAT1). Intratympanic administration of capsaicin transiently increased STAT1 activity and expression of downstream proinflammatory molecules. Capsaicin produced a transient increase in CD14-positive inflammatory cells into the cochlea, which mimicked the temporal course of STAT1 activation but did not alter the expression of apoptotic genes or damage to outer hair cells. In addition, trans-tympanic administration of STAT1 short interfering RNA protected against capsaicin-induced hearing loss. These data suggest that activation of TRPV1 mediates temporary hearing loss by initiating an inflammatory process in the cochlea via activation of NOX3 and STAT1. Thus, these proteins represent reasonable targets for ameliorating hearing loss. PMID:20712533

  11. Investigation of Electron Bernstein Wave (EBW) Coupling and its Critical Dependence on EBW Collisional Loss in High-β, H-mode ST Plasmas

    SciTech Connect

    Diem, S J; Caughman, J B; Efthimion, P C; Kugel, H; LeBlanc, B P; Phillips, C K; Preinhaelter, J; Sabbagh, S A; Urban, J; Wilgen, J B

    2010-02-03

    High-β spherical tokamak (ST) plasma conditions cut off propagation of electron cyclotron (EC) waves used for heating and current drive in conventional aspect ratio tokamaks. The electron Bernstein wave (EBW) has no density cutoff and is strongly absorbed and emitted at the EC harmonics, allowing EBWs to be used for heating and current drive in STs. However, this application requires efficient EBW coupling in the high-β, H-mode ST plasma regime. EBW emission (EBE) diagnostics and modelling have been employed on the National Spherical Torus Experiment (NSTX) to study oblique EBW to O-mode (B–X–O) coupling and propagation in H-mode plasmas. Efficient EBW coupling was measured before the L–H transition, but rapidly decayed thereafter. EBE simulations show that EBW collisional damping prior to mode conversion (MC) in the plasma scrape off reduces the coupling efficiency during the H-mode phase when the electron temperature is less than 30 eV inside the MC layer. Lithium evaporation during H-mode plasmas was successfully used to reduce this EBW collisional damping by reducing the electron density and increase the electron temperature in the plasma scrape off. Lithium conditioning increased the measured B–X–O coupling efficiency from less than 10% to 60%, consistent with EBE simulations.

  12. RHIC AC DIPOLE DESIGN AND CONSTRUCTION.

    SciTech Connect

    BAI,M.; METH,M.; PAI,C.; PARKER,B.; PEGGS,S.; ROSER,T.; SANDERS,R.; TRBOJEVIC,D.; ZALTSMAN,A.

    2001-06-18

    Two ac dipoles with vertical and horizontal magnetic field have been proposed at RHIC for applications in linear and non-linear beam dynamics and spin manipulations. A magnetic field amplitude of 380 Gm is required to produce a coherent oscillation of 5 times the rms beam size at the top energy. We take the ac dipole frequency to be 1.0% of the revolution frequency away from the betatron frequency. To achieve the strong magnetic field with minimum power loss, an air-core magnet with two seven turn winding of low loss Litz wire resonating at 64 kHz is designed. The system is also designed to allow one to connect the two magnet winding in series to resonate at 37 kHz for the spin manipulation. Measurements of a half length prototype magnet are also presented.

  13. The multiphoton AC Stark effect

    NASA Astrophysics Data System (ADS)

    Rudolph, T. G.; Ficek, Z.; Freedhoff, H. S.

    1998-02-01

    We study the interaction of a two-level atom with two intense lasers: a strong laser of Rabi frequency 2Ω on resonance with the atomic transition, and a weaker laser detuned by 2Ω/n, i.e. by a subharmonic of the Rabi frequency of the first. The second laser "dresses" the dressed states created by the first in an n-photon process. We calculate the energy levels and eigenstates of this "doubly-dressed" atom, and find a new phenomenon: the splitting of the energy levels due to an n-photon coupling between them, resulting in a multiphoton AC Stark effect. We illustrate this effect in the fluorescence spectrum, and show that the spectrum contains triplets at the subharmonic as well as harmonic resonance frequencies with a clear dependence on the order n of the resonance and the ratio α of the Rabi frequencies of the lasers

  14. Tevatron AC dipole system

    SciTech Connect

    Miyamoto, R.; Kopp, S.E.; Jansson, A.; Syphers, M.J.; /Fermilab

    2007-06-01

    The AC dipole is an oscillating dipole magnet which can induce large amplitude oscillations without the emittance growth and decoherence. These properties make it a good tool to measure optics of a hadron synchrotron. The vertical AC dipole for the Tevatron is powered by an inexpensive high power audio amplifier since its operating frequency is approximately 20 kHz. The magnet is incorporated into a parallel resonant system to maximize the current. The use of a vertical pinger magnet which has been installed in the Tevatron made the cost relatively inexpensive. Recently, the initial system was upgraded with a more powerful amplifier and oscillation amplitudes up to 2-3{sigma} were achieved with the 980 GeV proton beam. This paper discusses details of the Tevatron AC dipole system and also shows its test results.

  15. ac bidirectional motor controller

    NASA Technical Reports Server (NTRS)

    Schreiner, K.

    1988-01-01

    Test data are presented and the design of a high-efficiency motor/generator controller at NASA-Lewis for use with the Space Station power system testbed is described. The bidirectional motor driver is a 20 kHz to variable frequency three-phase ac converter that operates from the high-frequency ac bus being designed for the Space Station. A zero-voltage-switching pulse-density-modulation technique is used in the converter to shape the low-frequency output waveform.

  16. AC/RF Superconductivity

    SciTech Connect

    Ciovati, Gianluigi

    2015-02-01

    This contribution provides a brief introduction to AC/RF superconductivity, with an emphasis on application to accelerators. The topics covered include the surface impedance of normal conductors and superconductors, the residual resistance, the field dependence of the surface resistance, and the superheating field.

  17. AC solar cell

    SciTech Connect

    Schutten, H.P.; Benjamin, J.A.; Lade, R.W.

    1986-03-18

    An AC solar cell is described comprising: a pair of PN junction type solar cells connected in antiparallel between a pair of main terminals; and means for electrically directing light alternatingly without mechanical movement on the PN junctions to generate an alternating potential across the main terminals.

  18. AC 67 Launch Video

    NASA Technical Reports Server (NTRS)

    1987-01-01

    Live footage of the Unmanned Atlas Centaur (AC) 67 launch is presented on March 26, 1987 at the WESH television station in Florida. Lightning is shown after 49 seconds into the flight. The vehicle is totally destroyed due to a cloud-to-ground lightning flash.

  19. Low-Loss Wide-Band Floating Electrode Type Unidirectional Transducer Filters and Ladder-Type Resonator Filters Using High-Temperature-Stable High Electromechanical Coupling Surface Acoustic Wave Substrates

    NASA Astrophysics Data System (ADS)

    Yamanouchi, Kazuhiko; Ishii, Toru

    2003-05-01

    The important properties required for surface acoustic wave (SAW) substrates are large electromechanical coupling coefficients (k2), small temperature coefficient of frequency (TCF), low propagation loss, among other. LiNbO3 is a good SAW substrate because of its good properties and large size. We developed SiO2/rotated Y-cut, X-propagating LiNbO3 leaky SAW substrates with a large k2 (over 0.2) and zero TCF at a small thickness of SiO2 of H/λ=0.2 (H: SiO2 film thickness, λ: SAW wave-length) compared to those of other substrates and zero propagation attenuation in the case of metalized surface. In this paper, the theoretical and experimental results for SAW filters, resonators and resonator filters are described. The low-loss filters using floating electrode type unidirectional transducer (FEUDT) showed an insertion loss of below 1 dB at a center frequency of 400 MHz and bandwidth of 20 MHz. Also, the resonator showed the wide-band characteristics and resonator filters showed a bandwidth of 80 MHz at a center frequency of 500 MHz.

  20. CMOS-compatible spot-size converter for optical fiber to sub-μm silicon waveguide coupling with low-loss low-wavelength dependence and high tolerance to misalignment

    NASA Astrophysics Data System (ADS)

    Picard, Marie-Josée.; Latrasse, Christine; Larouche, Carl; Painchaud, Yves; Poulin, Michel; Pelletier, François; Guy, Martin

    2016-03-01

    One of the biggest challenges of silicon photonics is the efficient coupling of light between the sub-micron SiP waveguides and a standard optical fiber (SMF-28). We recently proposed a novel approach based on a spot-size converter (SSC) that fulfills this need. The SSC integrates a tapered silicon waveguide and a superimposed structure made of a plurality of rods of high index material, disposed in an array-like configuration and embedded in a cladding of lower index material. This superimposed structure defines a waveguide designed to provide an efficient adiabatic transfer, through evanescent coupling, to a 220 nm thick Si waveguide tapered down to a narrow tip on one side, while providing a large mode overlap to the optical fiber on the other side. An initial demonstration was made using a SSC fabricated with post-processing steps. Great coupling to a SMF-28 fiber with a loss of 0.6 dB was obtained for TEpolarized light at 1550 nm with minimum wavelength dependence. In this paper, SSCs designed for operation at 1310 and 1550 nm for TE/TM polarizations and entirely fabricated in a CMOS fab are presented.

  1. AC power systems handbook

    SciTech Connect

    Whitaker, J.

    1991-01-01

    Transient disturbances are what headaches are made of. Whatever you call them-spikes, surges, are power bumps-they can take your equipment down and leave you with a complicated and expensive repair job. Protection against transient disturbances is a science that demands attention to detail. This book explains how the power distribution system works, what can go wrong with it, and how to protect a facility against abnormalities. system grounding and shielding are covered in detail. Each major method of transient protection is analyzed and its relative merits discussed. The book provides a complete look at the critical elements of the ac power system. Provides a complete look at the ac power system from generation to consumption. Discusses the mechanisms that produce transient disturbances and how to protect against them. Presents diagrams to facilitate system design. Covers new areas, such as the extent of the transient disturbance problem, transient protection options, and stand-by power systems.

  2. Quenching characteristics of a.c. superconducting coils

    NASA Astrophysics Data System (ADS)

    Akita, S.; Kasahara, H.; Torii, S.

    Quenching characteristics of two superconducting coils for a.c. use are investigated at different frequencies. One is impregnated with epoxy resin and the other is not. Both coils have experienced over 40 quenches in a.c. and d.c. The impregnated coil shows steady quenching currents for a.c. and the values are nearly the same as for d.c. On the other hand, quenching currents for a.c. in the non-impregnated coil are almost 80% of the trained-up d.c. quenching current and are scattered. Furthermore, the relationship between quenching currents and the estimated a.c. losses of the superconducting cable at the highest magnetic field point is investigated. According to the results of this investigation, the cause of quench in the impregnated coil is assumed to be the temperature rise of the winding due to a.c. losses, while the cause in the non-impregnated coil might be wire motion.

  3. Loss of Cav1.3 channels reveals the critical role of L-type and BK channel coupling in pacemaking mouse adrenal chromaffin cells.

    PubMed

    Marcantoni, Andrea; Vandael, David H F; Mahapatra, Satyajit; Carabelli, Valentina; Sinnegger-Brauns, Martina J; Striessnig, Joerg; Carbone, Emilio

    2010-01-13

    We studied wild-type (WT) and Cav1.3(-/-) mouse chromaffin cells (MCCs) with the aim to determine the isoform of L-type Ca(2+) channel (LTCC) and BK channels that underlie the pacemaker current controlling spontaneous firing. Most WT-MCCs (80%) were spontaneously active (1.5 Hz) and highly sensitive to nifedipine and BayK-8644 (1,4-dihydro-2,6-dimethyl-5-nitro-4-[2-(trifluoromethyl)phenyl]-3-pyridinecarboxylic acid, methyl ester). Nifedipine blocked the firing, whereas BayK-8644 increased threefold the firing rate. The two dihydropyridines and the BK channel blocker paxilline altered the shape of action potentials (APs), suggesting close coupling of LTCCs to BK channels. WT-MCCs expressed equal fractions of functionally active Cav1.2 and Cav1.3 channels. Cav1.3 channel deficiency decreased the number of normally firing MCCs (30%; 2.0 Hz), suggesting a critical role of these channels on firing, which derived from their slow inactivation rate, sizeable activation at subthreshold potentials, and close coupling to fast inactivating BK channels as determined by using EGTA and BAPTA Ca(2+) buffering. By means of the action potential clamp, in TTX-treated WT-MCCs, we found that the interpulse pacemaker current was always net inward and dominated by LTCCs. Fast inactivating and non-inactivating BK currents sustained mainly the afterhyperpolarization of the short APs (2-3 ms) and only partially the pacemaker current during the long interspike (300-500 ms). Deletion of Cav1.3 channels reduced drastically the inward Ca(2+) current and the corresponding Ca(2+)-activated BK current during spikes. Our data highlight the role of Cav1.3, and to a minor degree of Cav1.2, as subthreshold pacemaker channels in MCCs and open new interesting features about their role in the control of firing and catecholamine secretion at rest and during sustained stimulations matching acute stress. PMID:20071512

  4. Mass loss

    NASA Technical Reports Server (NTRS)

    Goldberg, Leo

    1987-01-01

    Observational evidence for mass loss from cool stars is reviewed. Spectra line profiles are used for the derivation of mass-loss rates with the aid of the equation of continuity. This equation implies steady mass loss with spherical symmetry. Data from binary stars, Mira variables, and red giants in globular clusters are examined. Silicate emission is discussed as a useful indicator of mass loss in the middle infrared spectra. The use of thermal millimeter-wave radiation, Very Large Array (VLA) measurement of radio emission, and OH/IR masers are discussed as a tool for mass loss measurement. Evidence for nonsteady mass loss is also reviewed.

  5. Shift in phenotypic variation coupled with rapid loss of genetic diversity in captive populations of Eristalis tenax (Diptera: Syrphidae): consequences for rearing and potential commercial use.

    PubMed

    Francuski, Ljubinka; Djurakic, Marko; Ludoski, Jasmina; Hurtado, Pilar; Pérez-Bañón, Celeste; Ståhls, Gunilla; Rojo, Santos; Milankov, Vesna

    2014-04-01

    Because of its importance as a pollinator and its potential economic usefulness for the biodegradation of organic animal waste, the genetic and phenotypic diversity of the drone fly, Eristalis tenax L. (Diptera: Syrphidae), was studied in both wild and captive populations from southeastern Europe. Wild specimens from a natural protected habitat (with low human impact), field crop habitat (semisynanthropic condition), and intensive pig farming habitat (synanthropic condition) were compared with a laboratory colony reared on artificial media An integrative approach was applied based on allozyme loci, cytochrome c oxidase I mitochondrial DNA, wing traits (size and shape), and abdominal color patterns. Our results indicate that the fourth and eighth generations of the laboratory colony show a severe lack of genetic diversity compared with natural populations. Reduced genetic diversity in subsequent generations (F4 and F8) of the laboratory colony was found to be linked with phenotypic divergence. Loss of genetic variability associated with phenotypic differentiation in laboratory samples suggests a founder effect, followed by stochastic genetic processes and inbreeding. Hence, our results have implications for captive bred Eristalis flies, which have been used in crop pollination and biodegradation of organic waste under synanthropic conditions. PMID:24772566

  6. Novel Probes Establish Mas-Related G Protein-Coupled Receptor X1 Variants as Receptors with Loss or Gain of Function.

    PubMed

    Heller, Daniel; Doyle, Jamie R; Raman, Venkata S; Beinborn, Martin; Kumar, Krishna; Kopin, Alan S

    2016-02-01

    The Mas-related G protein-coupled receptor X1 (MrgprX1) is a human seven transmembrane-domain protein with a putative role in nociception and pruritus. This receptor is expressed in dorsal root ganglion neurons and is activated by a variety of endogenous peptides, including bovine adrenal medulla peptide (BAM) and γ2-melanocyte-stimulating hormone (γ2-MSH). In the present work, we study how naturally occurring missense mutations alter the activity of MrgprX1. To characterize selected receptor variants, we initially used the endogenous peptide ligand BAM8-22. In addition, we generated and characterized a panel of novel recombinant and synthetic peptide ligands. Our studies identified a mutation in the second intracellular loop of MrgprX1, R131S, that causes a decrease in both ligand-mediated and constitutive signaling. Another mutation in this region, H133R, results in a gain of function phenotype reflected by an increase in ligand-mediated signaling. Using epitope-tagged variants, we determined that the alterations in basal and ligand-mediated signaling were not explained by changes in receptor expression levels. Our results demonstrate that naturally occurring mutations can alter the pharmacology of MrgprX1. This study provides a theoretical basis for exploring whether MrgprX1 variability underlies differences in somatosensation within human populations. PMID:26582731

  7. ACS Algorithm in Discrete Ordinates for Pressure Vessel Dosimetry

    NASA Astrophysics Data System (ADS)

    Walters, William; Haghighat, Alireza

    2016-02-01

    The Adaptive Collision Source (ACS) method can solve the Linear Boltzmann Equation (LBE) more efficiently by adaptation of the angular quadrature order. This is similar to, and essentially an extension of, the first collision source method. Previously, the ACS methodology has been implemented into the TITAN discrete ordinates code, and has shown speedups of 2-4 on a simple test problem, with very little loss of accuracy (within a provided adaptive tolerance). This work examines the use of the ACS method for a more realistic problem: pressure vessel dosimetry with the VENUS-2 MOX-fuelled reactor dosimetry benchmark. The ACS method proved to be able to obtain accurate results while being approximately twice as efficient as using a constant quadrature in a standard source iteration scheme.

  8. High-Frequency ac Power-Distribution System

    NASA Technical Reports Server (NTRS)

    Hansen, Irving G.; Mildice, James

    1987-01-01

    Loads managed automatically under cycle-by-cycle control. 440-V rms, 20-kHz ac power system developed. System flexible, versatile, and "transparent" to user equipment, while maintaining high efficiency and low weight. Electrical source, from dc to 2,200-Hz ac converted to 440-V rms, 20-kHz, single-phase ac. Power distributed through low-inductance cables. Output power either dc or variable ac. Energy transferred per cycle reduced by factor of 50. Number of parts reduced by factor of about 5 and power loss reduced by two-thirds. Factors result in increased reliability and reduced costs. Used in any power-distribution system requiring high efficiency, high reliability, low weight, and flexibility to handle variety of sources and loads.

  9. Hair Loss

    MedlinePlus

    ... may cause hair loss in women. If your hair loss has occurred gradually with advancing age, FOLLICULAR DEGENERATION may be the cause. Post-pregnancy hormone changes usually reverse themselves without any treatment. While follicular degeneration cannot ...

  10. Modelling ac ripple currents in HTS coated conductors

    NASA Astrophysics Data System (ADS)

    Xu, Zhihan; Grilli, Francesco

    2015-10-01

    Dc transmission using high temperature superconducting (HTS) coated conductors (CCs) offers a promising solution to the globally growing demand for effective, reliable and economic transmission of green energy up to the gigawatt level over very long distances. The credible estimation of the losses and thereby the heat dissipation involved, where ac ripples (introduced in rectification/ac-dc conversion) are viewed as a potential source of notable contribution, is highly essential for the rational design of practical HTS dc transmission cables and corresponding cryogenic systems to fulfil this demand. Here we report a targeted modelling study into the ac losses in a HTS CC subject to dc and ac ripple currents simultaneously, by solving Maxwell’s equations using the finite element method (FEM) in the commercial software package COMSOL. It is observed that the instantaneous loss exhibits only one peak per cycle in the HTS CC subject to sinusoidal ripples, given that the amplitude of the ac ripples is smaller than approximately 20% of that of the dc current. This is a distinct contrast to the usual observation of two peaks per cycle in a HTS CC subject to ac currents only. The unique mechanism is also revealed, which is directly associated with the finding that, around any local minima of the applied ac ripples, the critical state of -J c is never reached at the edges of the HTS CC, as it should be according to the Bean model. When running further into the longer term, it is discovered that the ac ripple loss of the HTS CC in full-wave rectification decays monotonically, at a speed which is found to be insensitive to the frequency of the applied ripples within our targeted situations, to a relatively low level of approximately 1.38 × 10-4 W m-1 in around 1.7 s. Comparison between this level and other typical loss contributions in a HTS dc cable implies that ac ripple currents in HTS CCs should only be considered as a minor source of dissipation in superconducting dc

  11. Weight loss is coupled with improvements to affective state in obese participants engaged in behavior change therapy based on incremental, self-selected "small changes".

    PubMed

    Paxman, Jenny R; Hall, Anna C; Harden, Charlotte J; O'Keeffe, Jean; Simper, Trevor N

    2011-05-01

    The aim of this study was to investigate the effects of a group behavior change intervention involving self-selected, contextualized, and mediated goal setting on anthropometric, affective, and dietary markers of health. It was hypothesized that the intervention would elicit changes consistent with accepted health recommendations for obese individuals. A rolling program of 12-week "Small Changes" interventions during 24 months recruited 71 participants; each program accommodated 10 to 13 adults (body mass index [BMI] ≥ 30 kg/m²). Fifty-eight participants completed Small Changes. Repeated measures were made at baseline, 6 and 12 weeks. Anthropometric measures included height and weight (to calculate BMI), body composition, waist circumference, and blood pressure. Affective state was monitored using relevant validated questionnaires. Dietary assessment used 3-day household measures food diaries with Schofield equations to monitor underreporting. Relevant blood measures were recorded throughout. Across the measurement period, Small Changes elicited a significant reduction in body weight (baseline, 102.95 ± 15.47 vs 12 weeks 100.09 ± 16.01 kg, P < .0005), coupled with associated significant improvements in BMI, body fat percentage, and waist circumference measures. There were additional significant positive changes in measures of affective state including general well-being (baseline, 58.92 ± 21.22 vs 12 weeks 78.04 ± 14.60, P < .0005) and total mood disturbance (baseline, 31.19 ± 34.03 vs 12 weeks 2.67 ± 24.96, P < .0005). Dietary changes that occurred were largely consistent with evidenced-based recommendations for weight management and included significant reductions in total energy intake and in fat and saturated fat as a proportion of energy. The Small Changes approach can elicit a range of health-orientated benefits for obese participants, and although further work is needed to ascertain the longevity of such effects, the outcomes from Small Changes are

  12. Three phase AC motor controller

    DOEpatents

    Vuckovich, Michael; Wright, Maynard K.; Burkett, John P.

    1984-03-20

    A motor controller for a three phase AC motor (10) which is adapted to operate bidirectionally from signals received either from a computer (30) or a manual control (32). The controller is comprised of digital logic circuit means which implement a forward and reverse command signal channel (27, 29) for the application of power through the forward and reverse power switching relays (16, 18, 20, 22). The digital logic elements are cross coupled to prevent activation of both channels simultaneously and each includes a plugging circuit (65, 67) for stopping the motor upon the removal of control signal applied to one of the two channels (27, 29) for a direction of rotation desired. Each plugging circuit (65, 67) includes a one-shot pulse signal generator (88, 102) which outputs a single pulse signal of predetermined pulsewidth which is adapted to inhibit further operation of the application of power in the channel which is being activated and to apply a reversal command signal to the other channel which provides a reversed phase application of power to the motor for a period defined by the pulse-width output of the one-shot signal generator to plug the motor (10) which will then be inoperative until another rotational command signal is applied to either of the two channels.

  13. Identification of /sup 233/Ac

    SciTech Connect

    Chu, Y.Y.; Zhou, M.L.

    1983-09-01

    We report in this paper identification of the new isotope /sup 233/Ac. Uranium targets were irradiated with 28 GeV protons; after rapid retrieval of the target and separation of actinium from thorium, /sup 233/Ac was allowed to decay into the known /sup 233/Th daughter. Exhaustive chemical purification was employed to permit the identification of /sup 233/Th via its characteristic ..gamma.. radiations. The half-life derived for /sup 233/Ac from several experiments is 2.3 +- 0.3 min. The production cross section for /sup 233/Ac is 100 ..mu..b.

  14. Methods of attenuating wind turbine ac generator output variations

    NASA Technical Reports Server (NTRS)

    Gold, H.

    1978-01-01

    Wind speed variation, tower blockage and structural and inertial factors produce unsteady torque in wind turbines. Methods for modifying the turbine torque so that steady torque is delivered to the coupled ac generator are discussed. The method that may evolve will be influenced by the power use that develops and the trade-offs of cost, weight and complexity.

  15. Superconductor films with improved flux pinning and reduced AC losses

    DOEpatents

    Goyal, Amit

    2011-04-05

    The present invention relates to a method for producing a defect-containing superconducting film, the method comprising (a) depositing a phase-separable layer epitaxially onto a biaxially-textured substrate, wherein the phase-separable layer includes at least two phase-separable components; (b) achieving nanoscale phase separation of the phase-separable layer such that a phase-separated layer including at least two phase-separated components is produced; and (c) depositing a superconducting film epitaxially onto said phase-separated components of the phase-separated layer such that nanoscale features of the phase-separated layer are propagated into the superconducting film.

  16. AC resistance measuring instrument

    DOEpatents

    Hof, P.J.

    1983-10-04

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument. 8 figs.

  17. AC Resistance measuring instrument

    DOEpatents

    Hof, Peter J.

    1983-01-01

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument.

  18. Magnetic flux penetration into twisted multifilamentary coated superconductors subjected to ac transverse magnetic fields

    NASA Astrophysics Data System (ADS)

    Amemiya, Naoyuki; Sato, Susumu; Ito, Takeshi

    2006-12-01

    ac losses in superconductors are generated by the magnetic flux and current penetration into them. To reveal the magnetic flux and current penetration processes in twisted multifilamentary coated superconductors in which the thin superconductor layer is subdivided into filaments and then twisted as a whole for ac loss reduction, a theoretical model for electromagnetic field analysis was developed based on the power law E-J (electric-field-current-density) characteristic for the superconductor and a thin strip approximation of the conductor. The developed theoretical model was implemented into a numerical code using the finite element method to calculate and visualize the current and magnetic flux distributions. The magnetization losses in twisted multifilamentary coated superconductors exposed to ac transverse magnetic fields were calculated from the temporal evolutions of the current distribution to demonstrate the effect of the twisted multifilamentary architecture on ac loss reduction.

  19. System for automatically switching transformer coupled lines

    NASA Technical Reports Server (NTRS)

    Dwinell, W. S. (Inventor)

    1979-01-01

    A system is presented for automatically controlling transformer coupled alternating current electric lines. The secondary winding of each transformer is provided with a center tap. A switching circuit is connected to the center taps of a pair of secondary windings and includes a switch controller. An impedance is connected between the center taps of the opposite pair of secondary windings. The switching circuit has continuity when the AC lines are continuous and discontinuity with any disconnect of the AC lines. Normally open switching means are provided in at least one AC line. The switch controller automatically opens the switching means when the AC lines become separated.

  20. Splicing Efficiently Couples Optical Fibers

    NASA Technical Reports Server (NTRS)

    Lutes, G. F.

    1985-01-01

    Method of splicing single-mode optical fibers results in very low transmission losses through joined fiber ends. Coupling losses between joined optical-fiber ends only 0.1 dB. Method needs no special operator training.

  1. RG flow of AC conductivity in soft wall model of QCD

    NASA Astrophysics Data System (ADS)

    Bhatnagar, Neha; Siwach, Sanjay

    2016-03-01

    We study the Renormalization Group (RG) flow of AC conductivity in soft wall model of holographic QCD. We consider the charged black hole metric and the explicit form of AC conductivity is obtained at the cutoff surface. We plot the numerical solution of conductivity flow as a function of radial coordinate. The equation of gauge field is also considered and the numerical solution is obtained for AC conductivity as a function of frequency. The results for AC conductivity are also obtained for different values of chemical potential and Gauss-Bonnet couplings.

  2. Cooling Floor AC Systems

    NASA Astrophysics Data System (ADS)

    Jun, Lu; Hao, Ding; Hong, Zhang; Ce, Gao Dian

    The present HVAC equipments for the residential buildings in the Hot-summer-and-Cold-winter climate region are still at a high energy consuming level. So that the high efficiency HVAC system is an urgently need for achieving the preset government energy saving goal. With its advantage of highly sanitary, highly comfortable and uniform of temperature field, the hot-water resource floor radiation heating system has been widely accepted. This paper has put forward a new way in air-conditioning, which combines the fresh-air supply unit and such floor radiation system for the dehumidification and cooling in summer or heating in winter. By analyze its advantages and limitations, we found that this so called Cooling/ Heating Floor AC System can improve the IAQ of residential building while keep high efficiency quality. We also recommend a methodology for the HVAC system designing, which will ensure the reduction of energy cost of users.

  3. Digital ac monitor

    DOEpatents

    Hart, George W.; Kern, Jr., Edward C.

    1987-06-09

    An apparatus and method is provided for monitoring a plurality of analog ac circuits by sampling the voltage and current waveform in each circuit at predetermined intervals, converting the analog current and voltage samples to digital format, storing the digitized current and voltage samples and using the stored digitized current and voltage samples to calculate a variety of electrical parameters; some of which are derived from the stored samples. The non-derived quantities are repeatedly calculated and stored over many separate cycles then averaged. The derived quantities are then calculated at the end of an averaging period. This produces a more accurate reading, especially when averaging over a period in which the power varies over a wide dynamic range. Frequency is measured by timing three cycles of the voltage waveform using the upward zero crossover point as a starting point for a digital timer.

  4. Automated ac galvanomagnetic measurement system

    NASA Technical Reports Server (NTRS)

    Szofran, F. R.; Espy, P. N.

    1985-01-01

    An automated, ac galvanomagnetic measurement system is described. Hall or van der Pauw measurements in the temperature range 10-300 K can be made at a preselected magnetic field without operator attendance. Procedures to validate sample installation and correct operation of other system functions, such as magnetic field and thermometry, are included. Advantages of ac measurements are discussed.

  5. An H2A Histone Isotype, H2ac, Associates with Telomere and Maintains Telomere Integrity

    PubMed Central

    Tzeng, Tsai-Yu; Lin, I-Hsuan; Hsu, Ming-Ta

    2016-01-01

    Telomeres are capped at the ends of eukaryotic chromosomes and are composed of TTAGGG repeats bound to the shelterin complex. Here we report that a replication-dependent histone H2A isotype, H2ac, was associated with telomeres in human cells and co-immunoprecipitates with telomere repeat factor 2 (TRF2) and protection of telomeres protein 1 (POT1), whereas other histone H2A isotypes and mutations of H2ac did not bind to telomeres or these two proteins. The amino terminal basic domain of TRF2 was necessary for the association with H2ac and for the recruitment of H2ac to telomeres. Depletion of H2ac led to loss of telomeric repeat sequences, the appearance of dysfunctional telomeres, and chromosomal instability, including chromosomal breaks and anaphase bridges, as well as accumulation of telomere-associated DNA damage factors in H2ac depleted cells. Additionally, knockdown of H2ac elicits an ATM-dependent DNA damage response at telomeres and depletion of XPF protects telomeres against H2ac-deficiency-induced G-strand overhangs loss and DNA damage response, and prevents chromosomal instability. These findings suggest that the H2A isotype, H2ac, plays an essential role in maintaining telomere functional integrity. PMID:27228173

  6. Development of an AC Module System: Final Technical Report

    SciTech Connect

    Suparna Kadam; Miles Russell

    2012-06-15

    The GreenRay Inc. program focused on simplifying solar electricity and making it affordable and accessible to the mainstream population. This was accomplished by integrating a solar module, micro-inverter, mounting and monitoring into a reliable, 'plug and play' AC system for residential rooftops, offering the following advantages: (1) Reduced Cost: Reduction in installation labor with fewer components, faster mounting, faster wiring. (2) Maximized Energy Production: Each AC Module operates at its maximum, reducing overall losses from shading, mismatch, or module downtime. (3) Increased Safety. Electrical and fire safety experts agree that AC Modules have significant benefits, with no energized wiring or live connections during installation, maintenance or emergency conditions. (4) Simplified PV for a Broader Group of Installers. Dramatic simplification of design and installation of a solar power system, enabling faster and more efficient delivery of the product into the market through well-established, mainstream channels. This makes solar more accessible to the public. (5) Broadened the Rooftop Market: AC Modules enable solar for many homes that have shading, split roofs, or obstructions. In addition, due to the smaller building block size of 200W vs. 1000W, homeowners with budget limitations can start small and add to their systems over time. Through this DOE program GreenRay developed the all-in-one AC Module system with an integrated PV Module and microinverter, custom residential mounting and performance monitoring. Development efforts took the product from its initial concept, through prototypes, to a commercial product sold and deployed in the residential market. This pilot deployment has demonstrated the technical effectiveness of the AC Module system in meeting the needs and solving the problems of the residential market. While more expensive than the traditional central inverter systems at the pilot scale, the economics of AC Modules become more and more

  7. Exchange anisotropy determined by magnetic field dependence of ac susceptibility

    NASA Astrophysics Data System (ADS)

    Rodríguez-Suárez, R. L.; Vilela Leão, L. H.; de Aguiar, F. M.; Rezende, S. M.; Azevedo, A.

    2003-10-01

    ac susceptibility measurements of ferromagnetic/antiferromagnetic (FM/AF) bilayers are usually performed as a function of the temperature. In this work we describe measurements of transverse biased ac susceptibility (χt) of FM/AF bilayers as a function of the applied magnetic field H0. The measurements were carried out at room temperature by means of an ac magneto-optical Kerr effect susceptometer. The χt-1(H0) dependence, at the saturation magnetization regime, exhibits a linear behavior with the applied field parallel and perpendicular to the exchange bias direction. The linear extrapolation of χt-1 versus H0 cuts the abscissa at asymmetrical values of field due to the exchange bias coupling. The inverse susceptibility is calculated in the saturation regime by a model, which takes into account the free energy of both layers plus a term corresponding to the interfacial coupling. The exchange coupling field (HE) and uniaxial anisotropy (HU) are extracted from the best fit to the experimental results. The results obtained are crosschecked by those obtained from ferromagnetic resonance (FMR) and dc magnetometry. The measurements of the exchange bias and the uniaxial field in all of the three analyzed bilayers gave values that are consistently lower when measured by FMR than those obtained by ac and dc magnetometry. It is argued that the apparently discrepant values of HE and HU, obtained by different techniques, might be explained by existence of unstable AF grains at the AF/FM interface.

  8. Interplay between electron overheating and ac Josephson effect

    NASA Astrophysics Data System (ADS)

    De Cecco, A.; Le Calvez, K.; Sacépé, B.; Winkelmann, C. B.; Courtois, H.

    2016-05-01

    We study the response of high-critical-current proximity Josephson junctions to a microwave excitation. Electron overheating in such devices is known to create hysteretic dc voltage-current characteristics. Here we demonstrate that it also strongly influences the ac response. The interplay of electron overheating and ac Josephson dynamics is revealed by the evolution of the Shapiro steps with the microwave drive amplitude. Extending the resistively shunted Josephson junction model by including a thermal balance for the electronic bath coupled to phonons, a strong electron overheating is obtained.

  9. A type III ACC synthase, ACS7, is involved in root gravitropism in Arabidopsis thaliana

    PubMed Central

    Chang, Ing-Feng

    2013-01-01

    Ethylene is an important plant hormone that regulates developmental processes in plants. The ethylene biosynthesis pathway is a highly regulated process at both the transcriptional and post-translational level. The transcriptional regulation of these ethylene biosynthesis genes is well known. However, post-translational modifications of the key ethylene biosynthesis enzyme 1-aminocyclopropane-1-carboxylate (ACC) synthase (ACS) are little understood. In vitro kinase assays were conducted on the type III ACS, AtACS7, fusion protein and peptides to determine whether the AtACS7 protein can be phosphorylated by calcium-dependent protein kinase (CDPK). AtACS7 was phosphorylated at Ser216, Thr296, and Ser299 by AtCDPK16 in vitro. To investigate further the function of the ACS7 gene in Arabidopsis, an acs7-1 loss-of-function mutant was isolated. The acs7-1 mutant exhibited less sensitivity to the inhibition of root gravitropism by treatment with the calcium chelator ethylene glycol tetraacetic acid (EGTA). Seedlings were treated with gradient concentrations of ACC. The results showed that a certain concentration of ethylene enhanced the gravity response. Moreover, the acs7-1 mutant was less sensitive to inhibition of the gravity response by treatment with the auxin polar transport inhibitor 1-naphthylphthalamic acid, but exogenous ACC application recovered root gravitropism. Altogether, the results indicate that AtACS7 is involved in root gravitropism in a calcium-dependent manner in Arabidopsis. PMID:23943848

  10. Operation Method for AC Motor Control during Power Interruption in Direct AC/AC Converter System

    NASA Astrophysics Data System (ADS)

    Shizu, Keiichiro; Azuma, Satoshi

    Direct AC/AC converters have been studied due to their potential use in power converters with no DC-link capacitor, which can contribute to the miniaturization of power converters. However, the absence of a DC-link capacitor makes it difficult to control the AC motor during power interruption. First, this paper proposes a system that realizes AC motor control during power interruption by utilizing a clamp capacitor. In general, direct AC/AC converters have a clamp circuit consisting of a rectifier diode(s) and a clamp capacitor in order to avoid over-voltages. In the proposed system, there is an additional semiconductor switch reverse-parallel to the rectifier diode(s), and the clamp capacitor voltage can be utilized for AC motor control by turning on the additional switch. Second, this paper discusses an operation method for AC motor control and clamp capacitor voltage control during power interruption. In the proposed method “DC-link voltage control”, the kinetic energy in the AC motor is transformed into electrical energy and stored in the clamp capacitor; the clamp capacitor is therefore charged and the capacitor voltage is controlled to remain constant at an instruction value. Third, this paper discusses a switching operation during power interruption. A dead-time is introduced between the operation of turning off all switches on the rectifier side and the operation of turning on the additional switch, which prevents the occurrence of a short circuit between the interrupted power source and the clamp capacitor. Finally, experimental results are presented. During power interruptions, an output current was continuously obtained and the clamp capacitor voltage was maintained to be equal to the instruction value of the capacitor voltage. These results indicate that both AC motor control and capacitor voltage control were successfully achieved by using the proposed system.

  11. Memory loss

    MedlinePlus

    ... usually include asking questions of family members and friends. For this reason, they should come to the appointment. Medical history questions may include: Type of memory loss, such as short-term or long-term ...

  12. Hair loss

    MedlinePlus

    ... that is applied to the scalp to stimulate hair growth. Other medicines, such as hormones, may be prescribed to decrease hair loss and promote hair growth. Drugs such as finasteride and dutasteride can be ...

  13. Hair Loss

    MedlinePlus

    ... Common baldness" usually means male-pattern baldness, or permanent-pattern baldness. It is also called androgenetic alopecia. ... will grow back normally. However, scarring can cause permanent hair loss. Hot oil hair treatments or chemicals ...

  14. Hair Loss

    MedlinePlus

    ... are stress, a low protein diet, a family history, or poor nutrition. Treatment for hair loss depends on the cause. In some cases, treating the underlying cause will correct the problem. Other treatments include medicines and hair restoration.

  15. Hearing Loss

    MedlinePlus

    ... Devices Can Help? Hearing aids. Hearing aids are electronic, battery-run devices that make sounds louder. There ... to turn up the volume. Cochlear implants. These electronic devices are for people with severe hearing loss. ...

  16. AC photovoltaic module magnetic fields

    SciTech Connect

    Jennings, C.; Chang, G.J.; Reyes, A.B.; Whitaker, C.M.

    1997-12-31

    Implementation of alternating current (AC) photovoltaic (PV) modules, particularly for distributed applications such as PV rooftops and facades, may be slowed by public concern about electric and magnetic fields (EMF). This paper documents magnetic field measurements on an AC PV module, complementing EMF research on direct-current PV modules conducted by PG and E in 1993. Although not comprehensive, the PV EMF data indicate that 60 Hz magnetic fields (the EMF type of greatest public concern) from PV modules are comparable to, or significantly less than, those from household appliances. Given the present EMF research knowledge, AC PV module EMF may not merit considerable concern.

  17. Ac traction gets on track

    SciTech Connect

    O`Connor, L.

    1995-09-01

    This article describes inverter-based ac traction systems which give freight locomotives greater adhesion, pulling power, and braking capacity. In the 1940s, dc traction replaced the steam engine as a source of train propulsion, and it has ruled the freight transportation industry ever since. But now, high-performance ac-traction systems, with their unprecedented levels of pulling power and adhesion, are becoming increasingly common on America`s freight railroads. In thousands of miles of demonstration tests, today`s ac-traction systems have outperformed traditional dc-motor driven systems. Major railroad companies are convinced enough of the benefits of ac traction to have integrated it into their freight locomotives.

  18. Hair Loss

    MedlinePlus

    ... psychosocial impact of hair loss have found patients’ self-esteem, body image and self-confidence to be negatively ... 1-2 Known psychosocial complications include depression, low self-esteem, altered self-image, and less frequent and enjoyable ...

  19. Universal dielectric loss in glass from simultaneous bias and microwave fields.

    PubMed

    Burin, Alexander L; Khalil, Moe S; Osborn, Kevin D

    2013-04-12

    We derive the ac dielectric loss in glasses due to resonant processes created by two-level systems and a swept electric field bias. It is shown that at sufficiently large ac fields and bias sweep rates, the nonequilibrium loss tangent created by the two fields approaches a universal maximum determined by the bare linear dielectric permittivity. In addition, this nonequilibrium loss tangent is derived for a range of bias sweep rates and ac amplitudes. A predicted loss function can be understood in a Landau-Zener theory and used to extract the two-level system density, dipole moment, and relaxation rate. PMID:25167300

  20. Magnetic core loss of ultrahigh strength FeCo alloys

    NASA Astrophysics Data System (ADS)

    Cheng, X. M.; Zhang, X. K.; Zhang, D. Z.; Lee, S. H.; Duckham, A.; Weihs, T. P.; Cammarata, R. C.; Xiao, John Q.; Chien, C. L.

    2003-05-01

    Hiperco® 50 alloy heat treated between 450 and 650 °C exhibits superior mechanical properties. We report the measurements of the ac core loss at various frequencies up to 4500 Hz of the Hiperco® 50 alloy samples annealed at 450 and 650 °C. The 650 °C annealed specimens have lower ac core loss than that of the 450 °C annealed ones. The total core loss, consisting of contributions from hysteresis core loss and eddy-current core loss, depends on frequency f as af+bf2. The eddy-current loss of a single laminate is minor compared to the hysteresis loss.

  1. Beam loss

    NASA Astrophysics Data System (ADS)

    VanGinneken, A.; Edwards, D.; Harrison, M.

    1989-04-01

    This paper presents results from simulations of beam losses during the operation of a superconducting accelerator. The calculations use a combination of hadron/electromagnetic cascade plus elastic scattering codes with accelerator tracking routines. These calculations have been used in conjunction with the design of the Fermilab Tevatron. First accelerator geometry is described. The rest of the paper discusses a detailed attempt to simulate a fast extraction cycle, essentially in chronological order. Beginning with an unperturbed beam, the simulation generates proton phase-space distributions incident on the electrostatic septum. These interact either elastically or inelastically with the septum wires, and the products of these interactions are traced through the machine. Where these leave the accelerator, energy deposition levels in the magnets are calculated together with the projected response of the beam-loss monitors in this region. Finally, results of the calculation are compared with experimental data. (AIP)

  2. Tomato ACS4 is necessary for timely start of and progression through the climacteric phase of fruit ripening

    PubMed Central

    Hoogstrate, Suzanne W.; van Bussel, Lambertus J. A.; Cristescu, Simona M.; Cator, Eric; Mariani, Celestina; Vriezen, Wim H.; Rieu, Ivo

    2014-01-01

    Climacteric fruit ripening, as it occurs in many fruit crops, depends on a rapid, autocatalytic increase in ethylene production. This agriculturally important process has been studied extensively, with tomato simultaneously acting both as a model species and target crop for modification. In tomato, the ethylene biosynthetic genes ACC SYNTHASE2 (ACS2) and ACS4 are highly expressed during fruit ripening, with a combined loss of both ACS2 and ACS4 activity preventing generation of the ethylene burst necessary for fruit ripening. However, the individual roles and importance of ACS2 and ACS4 have not been determined. In this study, we examined specifically the role of ACS4 by comparing the phenotype of an acs4 mutant firstly with that of the wild-type, and secondly with two novel ripening-inhibitor (rin) mutants. Ethylene production during ripening was significantly reduced in both acs4-1, and rin lines, with rin genotypes showing the weaker ethylene burst. Also i) the time between anthesis and the start of fruit ripening and ii) the time required to progress through ripening were significantly longer in acs4-1 than in the wild type, but shorter than in the strongest rin mutant. The delay in ripening was reflected in the lower expression of ripening-related transcripts during the mature green and light red ripening stages. Furthermore, expression of ACS2 and ACS4 was strongly dependent on a functional RIN gene, while ACS2 expression was largely independent of ACS4. Altogether, we show that ACS4 is necessary for normal progression of tomato fruit ripening and that mutation of this gene may provide a useful means for altering ripening traits. PMID:25278945

  3. Low frequency ac conduction and dielectric relaxation in pristine poly(3-octylthiophene) films

    NASA Astrophysics Data System (ADS)

    Singh, Ramadhar; Kumar, Jitendra; Singh, Rajiv K.; Rastogi, Ramesh C.; Kumar, Vikram

    2007-02-01

    The ac conductivity σ(ω)m, dielectric constant ɛ'(ω) and loss ɛ''(ω) of pristine poly(3-octylthiophene) (P3OT) films (thickness ~ 20 μm) have been measured in wide temperature (77 350 K) and frequency (100 Hz 10 MHz) ranges. At low temperatures, σ(ω)m can be described by the relation σ(ω)m = Aωs, where s is ~ 0.61 at 77 K and decreases with increasing temperature. A clear Debye-type loss peak is observed by subtracting the contribution of σdc from σ(ω)m. The frequency dependence of conductivity indicates that there is a distribution of relaxation times. This is confirmed by measurement of the dielectric constant as a function of frequency and temperature. Reasonable estimates of various electrical parameters such as effective dielectric constant (ɛp), phonon frequency (νph), Debye temperature (θD), polaron radius (rp), small-polaron coupling constant (\\Upsilon ), effective polaron mass (mp), the density of states at the Fermi level N(EF), average hopping distance (R) and average hopping energy (W) from dc conductivity measurements suggest the applicability of Mott's variable range hopping model in this system.

  4. Convective and Diffusive Energetic Particle Losses Induced by Shear Alfven Waves in the ASDEX Upgrade Tokamak

    SciTech Connect

    Garcia-Munoz, M.; Hicks, N.; Bilato, R.; Bobkov, V.; Bruedgam, M.; Fahrbach, H.-U.; Igochine, V.; Maraschek, M.; Sassenberg, K.; Voornveld, R. van; Classen, I. G. J.; Jaemsae, S.

    2010-05-07

    We present here the first phase-space characterization of convective and diffusive energetic particle losses induced by shear Alfven waves in a magnetically confined fusion plasma. While single toroidal Alfven eigenmodes (TAE) and Alfven cascades (AC) eject resonant fast ions in a convective process, an overlapping of AC and TAE spatial structures leads to a large fast-ion diffusion and loss. Diffusive fast-ion losses have been observed with a single TAE above a certain threshold in the fluctuation amplitude.

  5. Proposal of Current Control Method for High-Speed AC Motor System

    NASA Astrophysics Data System (ADS)

    Furutani, Shinichi; Satake, Akira

    In this paper, current control method for High-Speed AC Motor System is proposed. In High-Speed driving operation, Current controller tends to lose stability because of dead time caused by computational delay and Electromagnetic coupling included AC Motor Model. The Main purpose of the proposed method is reduction of dead time on current controller. Proposed method based model predictive control and optimizing of start timing. The Effectiveness of proposed method is confirmed by simulation results.

  6. New levitation scheme with AC superconducting magnet for EDS MAGLEV system

    SciTech Connect

    Kim, D.H.; Lee, J.K.; Hahn, S.Y.; Cha, G.

    1996-09-01

    This paper proposes a new magnetic levitation scheme which is able to generate levitation force for all speeds including a standstill. Auxiliary wheels which are needed in EDS MAGLEV vehicle can be eliminated. This scheme uses AC superconducting magnets to generate levitation force. In this paper, magnetic fields, forces and power dissipations generated by AC magnets moving above a conducting slab are calculated analytically. Results of calculation show characteristics of EDS system with AC magnet, such as levitation force and loss, are superior to those of EDS system with DC magnets for all speeds.

  7. Ac hysteresis loop measurement of stator-tooth in induction motor

    SciTech Connect

    Son, D.

    1999-09-01

    The properties of ac hysteresis loop of a stator tooth in a 5 hp induction motor was measured and analyzed. The load increase on the motor decreased magnetic induction, however increase the minor hysteresis loops in the high induction region. This effect caused increase in the core loss. Depending on condition of the motor, the core loss of the stator tooth can be 50% greater than the core loss under sinusoidal magnetic induction waveform.

  8. The ac53, ac78, ac101, and ac103 Genes Are Newly Discovered Core Genes in the Family Baculoviridae

    PubMed Central

    Garavaglia, Matías Javier; Miele, Solange Ana Belén; Iserte, Javier Alonso; Belaich, Mariano Nicolás

    2012-01-01

    The family Baculoviridae is a large group of insect viruses containing circular double-stranded DNA genomes of 80 to 180 kbp, which have broad biotechnological applications. A key feature to understand and manipulate them is the recognition of orthology. However, the differences in gene contents and evolutionary distances among the known members of this family make it difficult to assign sequence orthology. In this study, the genome sequences of 58 baculoviruses were analyzed, with the aim to detect previously undescribed core genes because of their remote homology. A routine based on Multi PSI-Blast/tBlastN and Multi HaMStR allowed us to detect 31 of 33 accepted core genes and 4 orthologous sequences in the Baculoviridae which were not described previously. Our results show that the ac53, ac78, ac101 (p40), and ac103 (p48) genes have orthologs in all genomes and should be considered core genes. Accordingly, there are 37 orthologous genes in the family Baculoviridae. PMID:22933288

  9. Simple Equipment for Imaging AC.

    ERIC Educational Resources Information Center

    Kamata, Masahiro; Anayama, Takayuki

    2003-01-01

    Presents an effective way to demonstrate the difference between direct current and alternating current using red and green LEDs. Describes how to make a tool that shows how an AC voltage changes with time using the afterimage effect of the LEDs. (Author/NB)

  10. Semiconductor ac static power switch

    NASA Technical Reports Server (NTRS)

    Vrancik, J.

    1968-01-01

    Semiconductor ac static power switch has long life and high reliability, contains no moving parts, and operates satisfactorily in severe environments, including high vibration and shock conditions. Due to their resistance to shock and vibration, static switches are used where accidental switching caused by mechanical vibration or shock cannot be tolerated.

  11. Low-loss nonlinear polaritonics

    SciTech Connect

    Moiseev, Sergey A.; Kamli, Ali A.; Sanders, Barry C.

    2010-03-15

    We propose a large low-loss cross-phase modulation between two coupled surface polaritons propagating through a double electromagnetically induced transparency medium situated close to a negative-index metamaterial. In particular, a mutual {pi} phase shift is attainable between the two pulses at the single-photon level.

  12. Voltage controller/current limiter for ac

    NASA Technical Reports Server (NTRS)

    Wu, T. T.

    1980-01-01

    Circuit protects ac power systems for overload failures, limits power surge and short-circuit currents to 150 percent of steady state level, regulates ac output voltage, and soft starts loads. Limiter generates dc error signal in response to line fluctuations and dumps power when overload is reached. Device is inserted between ac source and load.

  13. Rapid weight loss

    MedlinePlus

    ... loss-rapid weight loss; Overweight-rapid weight loss; Obesity-rapid weight loss; Diet-rapid weight loss ... for people who have health problems because of obesity. For these people, losing a lot of weight ...

  14. Memory loss.

    PubMed

    Flicker, Leon A; Ford, Andrew H; Beer, Christopher D; Almeida, Osvaldo P

    2012-02-01

    Most older people with memory loss do not have dementia. Those with mild cognitive impairment are at increased risk of progressing to dementia, but no tests have been shown to enhance the accuracy of assessing this risk. Although no intervention has been convincingly shown to prevent dementia, data from cohort studies and randomised controlled trials are compelling in indicating that physical activity and treatment of hypertension decrease the risk of dementia. There is no evidence that pharmaceutical treatment will benefit people with mild cognitive impairment. In people with Alzheimer's disease, treatment with a cholinesterase inhibitor or memantine (an N-methyl- D-aspartate receptor antagonist) may provide symptomatic relief and enhance quality of life, but does not appear to alter progression of the illness. Non-pharmacological strategies are recommended as first-line treatments for behavioural and psychological symptoms of dementia, which are common in Alzheimer's disease. Atypical antipsychotics have modest benefit in reducing agitation and psychotic symptoms but increase the risk of cardiovascular events. The role of antidepressants in managing depressive symptoms in patients with mild cognitive impairment is uncertain and may increase the risk of delirium and falls. PMID:22304604

  15. Simultaneous distribution of AC and DC power

    DOEpatents

    Polese, Luigi Gentile

    2015-09-15

    A system and method for the transport and distribution of both AC (alternating current) power and DC (direct current) power over wiring infrastructure normally used for distributing AC power only, for example, residential and/or commercial buildings' electrical wires is disclosed and taught. The system and method permits the combining of AC and DC power sources and the simultaneous distribution of the resulting power over the same wiring. At the utilization site a complementary device permits the separation of the DC power from the AC power and their reconstruction, for use in conventional AC-only and DC-only devices.

  16. ac-resistance-measuring instrument

    SciTech Connect

    Hof, P.J.

    1981-04-22

    An auto-ranging ac resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an ac excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance.

  17. Critically coupled surface phonon-polariton excitation in silicon carbide.

    PubMed

    Neuner, Burton; Korobkin, Dmitriy; Fietz, Chris; Carole, Davy; Ferro, Gabriel; Shvets, Gennady

    2009-09-01

    We observe critical coupling to surface phonon-polaritons in silicon carbide by attenuated total reflection of mid-IR radiation. Reflectance measurements demonstrate critical coupling by a double scan of wavelength and incidence angle. Critical coupling occurs when prism coupling loss is equal to losses in silicon carbide and the substrate, resulting in maximal electric field enhancement. PMID:19724526

  18. Achieving High Performance in AC-Field Driven Organic Light Sources

    PubMed Central

    Xu, Junwei; Carroll, David L.; Smith, Gregory M.; Dun, Chaochao; Cui, Yue

    2016-01-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m2 with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today’s OLEDs in performance. PMID:27063414

  19. Achieving High Performance in AC-Field Driven Organic Light Sources.

    PubMed

    Xu, Junwei; Carroll, David L; Smith, Gregory M; Dun, Chaochao; Cui, Yue

    2016-01-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m(2) with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today's OLEDs in performance. PMID:27063414

  20. Achieving High Performance in AC-Field Driven Organic Light Sources

    NASA Astrophysics Data System (ADS)

    Xu, Junwei; Carroll, David L.; Smith, Gregory M.; Dun, Chaochao; Cui, Yue

    2016-04-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m2 with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today’s OLEDs in performance.

  1. Nonlinear magnetization relaxation of superparamagnetic nanoparticles in superimposed ac and dc magnetic bias fields

    NASA Astrophysics Data System (ADS)

    Titov, Serguey V.; Déjardin, Pierre-Michel; El Mrabti, Halim; Kalmykov, Yuri P.

    2010-09-01

    The nonlinear ac response of the magnetization M(t) of a uniaxially anisotropic superparamagnetic nanoparticle subjected to both ac and dc bias magnetic fields of arbitrary strengths and orientations is determined by averaging Gilbert’s equation augmented by a random field with Gaussian white-noise properties in order to calculate exactly the relevant statistical averages. It is shown that the magnetization dynamics of the uniaxial particle driven by a strong ac field applied at an angle to the easy axis of the particle (so that the axial symmetry is broken) alters drastically leading to different nonlinear effects due to coupling of the thermally activated magnetization reversal mode with the precessional modes of M(t) via the driving ac field.

  2. Ac electrode diagnostics in ac-operated metal halide lamps

    NASA Astrophysics Data System (ADS)

    Luijks, G. M. J. F.; van Esveld, H. A.; Nijdam, S.; Weerdesteijn, P. A. M.

    2008-07-01

    A diagnostic technique is presented to determine the electrode work function in ac-operated metal halide lamps. The heart of the experimental set-up is a high-speed photodiode array detector, which is able to follow real-time variations of electrode tip temperature and near-electrode plasma emissions in ac-operated experimental YAG lamps, enabling discrimination between the anode and cathode effects. Electrode tip temperature ripples have been measured for 100 Hz square wave operation and simulated with an existing electrode model. By using the electrode work function as main fit parameter for the simulations it is found that the measured cooling effect of the electrode tip in a NaTlDy-iodide lamp is caused by a gas-phase emitter effect of Dy. It is concluded that Dy coverage of the electrode tip causes an effective work function reduction of 0.3 eV at 100 Hz square wave operation, considerably less than the 1.0 eV reduction measured earlier for dc operation.

  3. Peculiarities in electromagnetic behavior of MF NbTi composites for AC use

    SciTech Connect

    Hlasnik, I.; Fukui, S.; Amemiya, N.

    1994-07-01

    The paper presents results obtained in the study of the current-voltage characteristics, critical and quenching currents as well as of the AC transport current and magnetization losses in four series of fine filament NbTi composites prepared by Showa Electric Wire and Cable Co., Japan. Complementary measurements have been made also on a commercially available type T AC superconducting wire produced by GEC Alsthom Company, France. The samples differ in filament diameter, matrix thickness between filaments and in the number and structure of filament bundles in the composite. In two series of samples barrier type artificial pinning centers have been introduced to increase J{sub c} and decrease the normalized magnetization losses. The conclusions concerning the optimization of multifilamentary composites and cables for AC use at low working magnetic field are briefly reviewed.

  4. Structural, AC conductivity and dielectric properties of Sr-La hexaferrite

    NASA Astrophysics Data System (ADS)

    Singh, A.; Narang, S. B.; Singh, K.; Sharma, P.; Pandey, O. P.

    2006-03-01

    A series of M-type hexaferrite samples with composition Sr{1-x}La{x}Fe{12}O{19} (x = 0.00, 0.05, 0.15 and 0.25) were prepared by standard ceramic technique. AC electrical conductivity measurements were carried out at different frequencies (20 Hz 1 MHz) and at different temperatures. The dielectric constant and dielectric loss tangent were measured in the same range of frequencies. The experimental results indicate that AC electrical conductivity increases on increasing the frequency as well as the temperature, indicating magnetic semiconductor behavior of the samples. The increase in AC electrical conductivity with frequency and temperature has been explained on the basis of Koops Model whereas dielectric constant and dielectric loss tangent has been explained with the Maxwell Wagner type interfacial polarization in agreement with the Koops phenomenological theory.

  5. Electromechanical systems with transient high power response operating from a resonant ac link

    NASA Technical Reports Server (NTRS)

    Burrows, Linda M.; Hansen, Irving G.

    1992-01-01

    The combination of an inherently robust asynchronous (induction) electrical machine with the rapid control of energy provided by a high frequency resonant ac link enables the efficient management of higher power levels with greater versatility. This could have a variety of applications from launch vehicles to all-electric automobiles. These types of systems utilize a machine which is operated by independent control of both the voltage and frequency. This is made possible by using an indirect field-oriented control method which allows instantaneous torque control all four operating quadrants. Incorporating the ac link allows the converter in these systems to switch at the zero crossing of every half cycle of the ac waveform. This zero loss switching of the link allows rapid energy variations to be achieved without the usual frequency proportional switching loss. Several field-oriented control systems were developed under contract to NASA.

  6. Vision Loss, Sudden

    MedlinePlus

    ... of age-related macular degeneration. Spotlight on Aging: Vision Loss in Older People Most commonly, vision loss ... Some Causes and Features of Sudden Loss of Vision Cause Common Features* Tests Sudden loss of vision ...

  7. System for transmitting low frequency analog signals over AC power lines

    DOEpatents

    Baker, Steven P.; Durall, Robert L.; Haynes, Howard D.

    1989-09-05

    A system for transmitting low frequency analog signals over AC power lines using FM modulation. A low frequency analog signal to be transmitted is first applied to a voltage-to-frequency converter where it is converted to a signal whose frequency varies in proportion to the analog signal amplitude. This signal is then used to modulate the carrier frequency of an FM transmitter coupled to an AC power line. The modulation signal frequency range in selected to be within the response band of the FM transmitter. The FM modulated carrier signal is received by an FM receiver coupled to the AC power line, demodulated and the demodulated signal frequency is converted by a frequency-to-voltage converter back to the form of the original low frequency analog input signal.

  8. A system for tranmitting low frequency analog signals over ac power lines

    DOEpatents

    Baker, S.P.; Durall, R.L.; Haynes, H.D.

    1987-07-30

    A system for transmitting low frequency analog signals over ac power lines using FM modulation. A low frequency analog signal to be transmitted is first applied to a voltage-to-frequency converter where it is converted to a signal whose frequency varies in proportion to the analog signal amplitude. This signal is then used to modulate the carrier frequency of an FM transmitter coupled to an ac power line. The modulation signal frequency range is selected to be within the response band of the FM transmitter. The FM modulated carrier signal is received by an FM receiver coupled to the ac power line, demodulated and the demodulated signal frequency is converted by a frequency-to-voltage converter back to the form of the original low frequency analog input signal. 4 figs.

  9. System for transmitting low frequency analog signals over AC power lines

    DOEpatents

    Baker, Steven P.; Durall, Robert L.; Haynes, Howard D.

    1989-01-01

    A system for transmitting low frequency analog signals over AC power lines using FM modulation. A low frequency analog signal to be transmitted is first applied to a voltage-to-frequency converter where it is converted to a signal whose frequency varies in proportion to the analog signal amplitude. This signal is then used to modulate the carrier frequency of an FM transmitter coupled to an AC power line. The modulation signal frequency range in selected to be within the response band of the FM transmitter. The FM modulated carrier signal is received by an FM receiver coupled to the AC power line, demodulated and the demodulated signal frequency is converted by a frequency-to-voltage converter back to the form of the original low frequency analog input signal.

  10. The AC photovoltaic module is here!

    NASA Astrophysics Data System (ADS)

    Strong, Steven J.; Wohlgemuth, John H.; Wills, Robert H.

    1997-02-01

    This paper describes the design, development, and performance results of a large-area photovoltaic module whose electrical output is ac power suitable for direct connection to the utility grid. The large-area ac PV module features a dedicated, integrally mounted, high-efficiency dc-to-ac power inverter with a nominal output of 250 watts (STC) at 120 Vac, 60 H, that is fully compatible with utility power. The module's output is connected directly to the building's conventional ac distribution system without need for any dc wiring, string combiners, dc ground-fault protection or additional power-conditioning equipment. With its advantages, the ac photovoltaic module promises to become a universal building block for use in all utility-interactive PV systems. This paper discusses AC Module design aspects and utility interface issues (including islanding).

  11. Power Electronic Transformer based Three-Phase PWM AC Drives

    NASA Astrophysics Data System (ADS)

    Basu, Kaushik

    A Transformer is used to provide galvanic isolation and to connect systems at different voltage levels. It is one of the largest and most expensive component in most of the high voltage and high power systems. Its size is inversely proportional to the operating frequency. The central idea behind a power electronic transformer (PET) also known as solid state transformer is to reduce the size of the transformer by increasing the frequency. Power electronic converters are used to change the frequency of operation. Steady reduction in the cost of the semiconductor switches and the advent of advanced magnetic materials with very low loss density and high saturation flux density implies economic viability and feasibility of a design with high power density. Application of PET is in generation of power from renewable energy sources, especially wind and solar. Other important application include grid tied inverters, UPS e.t.c. In this thesis non-resonant, single stage, bi-directional PET is considered. The main objective of this converter is to generate adjustable speed and magnitude pulse width modulated (PWM) ac waveforms from an ac or dc grid with a high frequency ac link. The windings of a high frequency transformer contains leakage inductance. Any switching transition of the power electronic converter connecting the inductive load and the transformer requires commutation of leakage energy. Commutation by passive means results in power loss, decrease in the frequency of operation, distortion in the output voltage waveform, reduction in reliability and power density. In this work a source based partially loss-less commutation of leakage energy has been proposed. This technique also results in partial soft-switching. A series of converters with novel PWM strategies have been proposed to minimize the frequency of leakage inductance commutation. These PETs achieve most of the important features of modern PWM ac drives including 1) Input power factor correction, 2) Common

  12. Neurons from rat brain coupled to transistors

    NASA Astrophysics Data System (ADS)

    Vassanelli, S.; Fromherz, P.

    Field-effect transistors form spontaneously capacitive junctions with cultured nerve cells from rat brains. The transfer of ac signals from neurons to silicon is studied and used to parametrize an equivalent circuit. The coupling is distinctly weaker than in junctions assembled with leech nerve cells. The implications with respect to the recording and stimulation of neuronal activity by silicon devices are considered.

  13. Flux Coupling for Wheelchair Battery Chargers

    NASA Technical Reports Server (NTRS)

    Mclyman, C. W.

    1985-01-01

    Battery-charger concept for wheelchairs includes magnetic-flux coupling instead of electrical connections between power sources and wheelchairs. Concept meant to facilitate operation by patients whose disabilities make it difficult or impossible to maneuver common electrical plugs into or out of ac wall outlets.

  14. Construction of Tunnel Diode Oscillator for AC Impedance Measurement

    NASA Astrophysics Data System (ADS)

    Shin, J. H.; Kim, E.

    2014-03-01

    We construct a tunnel diode oscillator (TDO) to study electromagnetic response of a superconducting thin film. Highly sensitive tunnel diode oscillators allow us to detect extremely small changes in electromagnetic properties such as dielectric constant, ac magnetic susceptibility and magnetoresistance. A tunnel diode oscillator is a self-resonant oscillator of which resonance frequency is primarily determined by capacitance and inductance of a resonator. Amplitude of the signal depends on the quality factor of the resonator. The change in the impedance of the sample electromagnetic coupled to one of inductors in the resonator alters impedance of the inductor, and leads to the shift in the resonance frequency and the change of the amplitude.

  15. Fast or Slow, Either Head Can Start the Processive Run of Kinesin-2 KIF3AC.

    PubMed

    Zhang, Pengwei; Rayment, Ivan; Gilbert, Susan P

    2016-02-26

    Mammalian KIF3AC contains two distinct motor polypeptides and is best known for its role in organelle transport in neurons. Our recent studies showed that KIF3AC is as processive as conventional kinesin-1, suggesting that their ATPase mechanochemistry may be similar. However, the presence of two different motor polypeptides in KIF3AC implies that there must be a cellular advantage for the KIF3AC heterodimer. The hypothesis tested was whether there is an intrinsic bias within KIF3AC such that either KIF3A or KIF3C initiates the processive run. To pursue these experiments, a mechanistic approach was used to compare the pre-steady-state kinetics of KIF3AC to the kinetics of homodimeric KIF3AA and KIF3CC. The results indicate that microtubule collision at 11.4 μm(-1) s(-1) coupled with ADP release at 78 s(-1) are fast steps for homodimeric KIF3AA. In contrast, KIF3CC exhibits much slower microtubule association at 2.1 μm(-1) s(-1) and ADP release at 8 s(-1). For KIF3AC, microtubule association at 6.6 μm(-1) s(-1) and ADP release at 51 s(-1) are intermediate between the constants for KIF3AA and KIF3CC. These results indicate that either KIF3A or KIF3C can initiate the processive run. Surprisingly, the kinetics of the initial event of microtubule collision followed by ADP release for KIF3AC is not equivalent to 1:1 mixtures of KIF3AA plus KIF3CC homodimers at the same motor concentration. These results reveal that the intermolecular communication within the KIF3AC heterodimer modulates entry into the processive run regardless of whether the run is initiated by the KIF3A or KIF3C motor domain. PMID:26710851

  16. Low-frequency losses at high fields in multifilamentary superconductors

    SciTech Connect

    Zaleski, A.J.; Orlando, T.P.; Zieba, A.; Schwartz, B.B.; Foner, S.

    1984-12-01

    Low-frequency (approx.1 Hz) ac loss measurements were made at applied fields up to 20 T with field modulation amplitudes of up to 1 T. Results for the alternative in situ and powder metallurgy (P/M) processed Nb/sub 3/Sn and Nb--Al wires are presented for single-strand and multistrand geometries. Loss measurements for commercial continuous-fiber Nb/sub 3/Sn wires manufactured by Holec and Supercon also are presented and show that the effective fiber size determined by these ac-loss measurements corresponds to that measured optically. The effective fiber size for alternative processed wires was intermediate between the wire size and the fiber size, and the losses (and effective fiber size) were reduced by twisting. Multistrand geometries showed further reductions in losses. The smallest effective fiber size at high field was measured for P/M processed Nb--Al. The losses were fully hysteretic and the ac losses were used to determine the critical-current density at low fields where it was difficult to measure directly.

  17. RHIC spin flipper AC dipole controller

    SciTech Connect

    Oddo, P.; Bai, M.; Dawson, C.; Gassner, D.; Harvey, M.; Hayes, T.; Mernick, K.; Minty, M.; Roser, T.; Severino, F.; Smith, K.

    2011-03-28

    The RHIC Spin Flipper's five high-Q AC dipoles which are driven by a swept frequency waveform require precise control of phase and amplitude during the sweep. This control is achieved using FPGA based feedback controllers. Multiple feedback loops are used to and dynamically tune the magnets. The current implementation and results will be presented. Work on a new spin flipper for RHIC (Relativistic Heavy Ion Collider) incorporating multiple dynamically tuned high-Q AC-dipoles has been developed for RHIC spin-physics experiments. A spin flipper is needed to cancel systematic errors by reversing the spin direction of the two colliding beams multiple times during a store. The spin flipper system consists of four DC-dipole magnets (spin rotators) and five AC-dipole magnets. Multiple AC-dipoles are needed to localize the driven coherent betatron oscillation inside the spin flipper. Operationally the AC-dipoles form two swept frequency bumps that minimize the effect of the AC-dipole dipoles outside of the spin flipper. Both AC bumps operate at the same frequency, but are phase shifted from each other. The AC-dipoles therefore require precise control over amplitude and phase making the implementation of the AC-dipole controller the central challenge.

  18. Rigid reflection-asymmetric rotor description of the nucleus /sup 227/Ac

    SciTech Connect

    Leander, G.A.; Chen, Y.S.

    1987-03-01

    A model based on a static quadrupole and octupole deformation of the intrinsic nuclear shape gives an accurate description of the low-energy level spectrum and wave functions in /sup 227/Ac. Major discrepancies between strong-coupling theory and experiment are removed by taking into account the nonadiabaticity of the nucleonic motion.

  19. ac electroosmosis in rectangular microchannels.

    PubMed

    Campisi, Michele; Accoto, Dino; Dario, Paolo

    2005-11-22

    Motivated by the growing interest in ac electroosmosis as a reliable no moving parts strategy to control fluid motion in microfluidic devices for biomedical applications, such as lab-on-a-chip, we study transient and steady-state electrokinetic phenomena (electroosmosis and streaming currents) in infinitely extended rectangular charged microchannels. With the aid of Fourier series and Laplace transforms we provide a general formal solution of the problem, which is used to study the time-dependent response to sudden ac applied voltage differences in case of finite electric double layer. The Debye-Huckel approximation has been adopted to allow for an algebraic solution of the Poisson-Boltzmann problem in Fourier space. We obtain the expressions of flow velocity profiles, flow rates, streaming currents, as well as expressions of the complex hydraulic and electrokinetic conductances. We analyze in detail the dependence of the electrokinetic conductance on the extension of linear dimensions relative to the Debye length, with an eye on finite electric double layer effects. PMID:16351310

  20. Single event AC - DC electrospraying

    NASA Astrophysics Data System (ADS)

    Stachewicz, U.; Dijksman, J. F.; Marijnissen, J. C. M.

    2008-12-01

    Electrospraying is an innovative method to deposit very small amounts of, for example, biofluids (far less than 1 p1) that include DNA or protein molecules. An electric potential is applied between a nozzle filled with liquid and a counter electrode placed at 1-2 millimeter distance from the nozzle. In our set-up we use an AC field superposed on a DC field to control the droplet generation process. Our approach is to create single events of electrospraying triggered by one single AC pulse. During this pulse, the equilibrium meniscus (determined by surface tension, static pressure and the DC field) of the liquid changes rapidly into a cone and subsequently into a jet formed at the cone apex. Next, the jet breaks-up into fine droplets and the spraying stops. The meniscus returns to its equilibrium shape again. So far we obtained a stable and reproducible single event process for ethanol and ethylene glycol with water using glass pipettes. The results will be used to generate droplets on demand in a controlled way and deposit them on a pre-defined place on the substrate.

  1. Extending membrane pore lifetime with AC fields: A modeling study

    NASA Astrophysics Data System (ADS)

    Garner, Allen L.; Bogdan Neculaes, V.

    2012-07-01

    AC (sinusoidal) fields with frequencies from kilohertz to gigahertz have been used for gene delivery. To understand the impact of AC fields on electroporation dynamics, we couple a nondimensionalized Smoluchowski equation to an exact representation of the cell membrane voltage obtained solving the Laplace equation. The slope of the pore energy function, dφ/dr, with respect to pore radius is critical in predicting pore dynamics in AC fields because it can vary from positive, inducing pore shrinkage, to negative, driving pore growth. Specifically, the net sign of the integral of dφ/dr over time determines whether the average pore size grows (negative), shrinks (positive), or oscillates (zero) indefinitely about a steady-state radius, rss. A simple analytic relationship predicting the amplitude of the membrane voltage necessary for this behavior agrees well with simulation for frequencies from 500 kHz to 5 MHz for rss < 10 nm. For larger pore size (rss > 10 nm), dφ/dr oscillates about a negative value, suggesting that a net creation of pores may be necessary to maintain a constant pore size. In both scenarios, the magnitude of rss depends only upon the amplitude of the membrane voltage and not directly upon the applied field frequency other than the relationship between the amplitudes of the applied field and membrane voltage.

  2. ``Superfast'' and ``Hyperfast'' Electrophoresis in DC and AC Electric Fields

    NASA Astrophysics Data System (ADS)

    Demekhin, Evgeny; Korovyakovsky, Alex

    2006-11-01

    Movement of a small conducting spherical granule in an electrolyte solution under force of DC and AC fields is considered. The problem is described by strongly coupled nonlinear PDE system. The fact that it has two small parameters, the ratio of the ion double layer to the diffusion layer and the ratio of the diffusion layer to the granule's diameter, makes the problem unique and extremely difficult to solve. This is the reason why only solutions for some particular cases have been known. In this work for the first time, combining asymptotic and numerical methods, a complete theory of electrophoresis in DC and AC fields is developed. By special decomposition method the system is transformed to new variables. Analytical solution in the inner region results in the nonlinear Smoluchowski slip velocity. In the intermediate region convection-diffusion equation is solved numerically. In tern, the intermediate solution is matched with the outer solution of Laplace equation to complete the statement. For a strong DC field (``superfast'' electrophoresis) the theory predicts, in agreement with experiments, the granule's velocity to be proportional to the granule's size and squared external field; there is a large elongated vortex behind the granule and a small one near its equator. There is an excellent agreement with available experimental data. Granule's velocity for AC field becomes even larger than for DC, it has a maximum with respect to the field's frequency (``hyperfast'' electrophoresis).

  3. High-power test of annular-ring coupled structures for the J-PARC linac energy upgrade

    NASA Astrophysics Data System (ADS)

    Tamura, Jun; Ao, Hiroyuki; Nemoto, Yasuo; Asano, Hiroyuki; Suzuki, Takahiro

    2015-02-01

    Annular-ring coupled structures (ACSs) will increase the beam energy of the Japan proton accelerator research complex (J-PARC) linac from 181 to 400 MeV to achieve a beam power of 1 MW for a materials and life science experimental facility. The mass production of the ACS cavities commenced in March 2009. Before the installation, all cavities require power testing. High-power testing is essential not only for confirming the cavity's design performance but also for preventing delays in cavity conditioning schedule. However, the 2011 Tohoku earthquake damaged J-PARC facilities, including the ACS power-test area, and cavity conditioning was interrupted for two years. After the facility's restoration, two ACS cavities (M01 and M11) were conditioned. They performed 15-20% above the designed accelerating field of 4.2 MV/m. As M01 was initially conditioned six years ago, the most recent conditioning time required for M01 was drastically reduced. From this result, we confirmed that long-term stored ACS cavities purged with nitrogen gas do not produce critical cavity performance issues. During high-power operation of M11, which is a unique cavity equipped with a capacitive iris in a waveguide, no significant increases in the temperature and the discharge rate around the capacitive iris were observed. Even considering beam loss due to residual gas scattering, the vacuum pressure was sufficiently low (4 × 10-6 Pa). More stable operation can be expected following a month-long conditioning process before the beam is commissioned. M11's conditioning successfully demonstrated an auto-conditioning program, and we established the conditioning scheme using this auto-conditioning program for all ACS cavities in a limited time and with limited manpower.

  4. AC and DC conductivity of ionic liquid containing polyvinylidene fluoride thin films

    NASA Astrophysics Data System (ADS)

    Frübing, Peter; Wang, Feipeng; Kühle, Till-Friedrich; Gerhard, Reimund

    2016-01-01

    Polarisation processes and charge transport in polyvinylidene fluoride (PVDF) with a small amount (0.01-10 wt%) of the ionic liquid (IL) 1-ethyl-3-methylimidazolium nitrate ({[EMIM]}^+[{NO}_3]^-) are investigated by means of dielectric spectroscopy. The response of PVDF that contains more than 0.01 wt% IL is dominated by a low-frequency relaxation which shows typical signatures of electrode polarisation. Furthermore, the α a relaxation, related to the glass transition, disappears for IL contents of more than 1 wt%, which indicates that the amorphous phase loses its glass-forming properties and undergoes structural changes. The DC conductivity is determined from the low-frequency limit of the AC conductivity and from the dielectric loss peak related to the electrode polarisation. DC conductivities of 10^{-10} to 10^{-2} {S}/{m} are obtained—increasing with IL content and temperature. The dependence of the DC conductivity on the IL content follows a power law with an exponent greater than one, indicating an increase in the ion mobility. The temperature dependence of the DC conductivity shows Vogel-Fulcher-Tammann behaviour, which implies that charge transport is coupled to polymer chain motion. Mobile ion densities and ion mobilities are calculated from the DC conductivity and the dielectric loss related to electrode polarisation, with the results that less than one per cent of the total ion concentration contributes to the conductivity and that the strong increase in conductivity with temperature is mainly caused by a strong increase in ion mobility. This leads to the conclusion that in particular the ion mobility must be reduced in order to decrease the DC conductivity.

  5. Methods, systems and apparatus for controlling operation of two alternating current (AC) machines

    DOEpatents

    Gallegos-Lopez, Gabriel; Nagashima, James M.; Perisic, Milun; Hiti, Silva

    2012-02-14

    A system is provided for controlling two AC machines. The system comprises a DC input voltage source that provides a DC input voltage, a voltage boost command control module (VBCCM), a five-phase PWM inverter module coupled to the two AC machines, and a boost converter coupled to the inverter module and the DC input voltage source. The boost converter is designed to supply a new DC input voltage to the inverter module having a value that is greater than or equal to a value of the DC input voltage. The VBCCM generates a boost command signal (BCS) based on modulation indexes from the two AC machines. The BCS controls the boost converter such that the boost converter generates the new DC input voltage in response to the BCS. When the two AC machines require additional voltage that exceeds the DC input voltage required to meet a combined target mechanical power required by the two AC machines, the BCS controls the boost converter to drive the new DC input voltage generated by the boost converter to a value greater than the DC input voltage.

  6. Protection of superconducting AC windings

    SciTech Connect

    Verhaege, T.; Agnoux, C.; Tavergnier, J.P. ); Lacaze, A. ); Collet, M. )

    1992-01-01

    Recent progresses on multifilamentary wires open new prospects of 50-60 Hz applications for superconductivity. The problem of AC windings protection is more critical than that of DC windings, because of high current densities, and of high matrix resistivity: one should not allow the quenched wire to carry it nominal current for longer than a few milliseconds, otherwise permanent damage could occur. After a quench initiation, the protection system therefore has to switch off or drastically reduce the current very rapidly. In this paper, the authors propose various schemes, applicable when the conductor is made of several wires: active protection involves an ultra-rapid quench detection. It is based on the measurement of the current passing through the central resistive wire, and/or of unbalanced currents in the different superconducting wires. About 20 milliseconds after detection, a fast circuit-breaker switched off the current. A complementary passive protection is provided by the resistance developing during normal phase propagation.

  7. Hearing Loss in Adults.

    ERIC Educational Resources Information Center

    House, John W.

    1997-01-01

    This article discusses hearing loss in adults. It begins with an explanation of the anatomy of the ear and then explains the three types of hearing loss: conductive hearing loss, sensorineural hearing loss, and mixed conductive-sensorineural hearing loss. Tinnitus, hearing aids, and cochlear implants are also addressed. (CR)

  8. Magnetization losses in superconducting YBCO conductor-on-round-core (CORC) cables

    NASA Astrophysics Data System (ADS)

    Majoros, M.; Sumption, M. D.; Collings, E. W.; van der Laan, D. C.

    2014-12-01

    Described are the results of magnetization loss measurements made at 77 K on several YBCO conductor-on-round-core (CORC) cables in ac magnetic fields of up to 80 mT in amplitude and frequencies of 50 to 200 Hz, applied perpendicular to the cable axis. The cables contained up to 40 tapes that were wound in as many as 13 layers. Measurements on the cables with different configurations were made as functions of applied ac field amplitude and frequency to determine the effects of their layout on ac loss. In large scale devices such as e.g. Superconducting Magnetic Energy Storage (SMES) magnets, the observed ac losses represent less than 0.1% of their stored energy.

  9. Characterization of genes in the cellulose-synthesizing operon (acs operon) of Acetobacter xylinum: implications for cellulose crystallization.

    PubMed Central

    Saxena, I M; Kudlicka, K; Okuda, K; Brown, R M

    1994-01-01

    The synthesis of an extracellular ribbon of cellulose in the bacterium Acetobacter xylinum takes place from linearly arranged, membrane-localized, cellulose-synthesizing and extrusion complexes that direct the coupled steps of polymerization and crystallization. To identify the different components involved in this process, we isolated an Acetobacter cellulose-synthesizing (acs) operon from this bacterium. Analysis of DNA sequence shows the presence of three genes in the acs operon, in which the first gene (acsAB) codes for a polypeptide with a molecular mass of 168 kDa, which was identified as the cellulose synthase. A single base change in the previously reported DNA sequence of this gene, resulting in a frameshift and synthesis of a larger protein, is described in the present paper, along with the sequences of the other two genes (acsC and acsD). The requirement of the acs operon genes for cellulose production was determined using site-determined TnphoA/Kanr GenBlock insertion mutants. Mutant analysis showed that while the acsAB and acsC genes were essential for cellulose production in vivo, the acsD mutant produced reduced amounts of two cellulose allomorphs (cellulose I and cellulose II), suggesting that the acsD gene is involved in cellulose crystallization. The role of the acs operon genes in determining the linear array of intramembranous particles, which are believed to be sites of cellulose synthesis, was investigated for the different mutants; however, this arrangement was observed only in cells that actively produced cellulose microfibrils, suggesting that it may be influenced by the crystallization of the nascent glucan chains. Images PMID:8083166

  10. Large signal dielectric losses in electrostrictive materials

    NASA Astrophysics Data System (ADS)

    Robinson, Harold C.

    2000-06-01

    The dielectric loss factor tan (delta) is a critical parameter in transducer design and performance prediction, as it is directly related to the electrical energy lost to Joule heating. A method for calculating the equivalent loss factor of 'quasi linear' materials from a measured major polarization vs. field loop by extending the standard definition of tan (delta) for a linear lossy capacitor to nonlinear materials is presented. To extract effective loss tangents for minor loops from the major loops, an area correction algorithm was implemented. This algorithm proves to be nearly exact for all bias and drive levels in the case of an ideal linear capacitor. In most cases, the effective tan (delta) calculated from a major loop agrees fairly well with that calculated from a directly measured minor loop. Finally, the behavior of the loss tangent as a function of the dc bias field, ac drive field, prestress level and temperature will be examined. It shall be shown that, in general, the effective loss factor of lead magnesium niobate-lead titanate decreases with increasing temperature, consistent with its transition from a piezoelectric to an electrostrictive material, but increases with prestress. At a fixed temperature and prestress level, the loss factor increases as the bias or drive levels decrease. However, at certain bias levels, the loss tangent is practically the same, regardless of the drive level.

  11. Helix coupling

    DOEpatents

    Ginell, W.S.

    1982-03-17

    A coupling for connecting helix members in series, which consists of a pair of U-shaped elements, one of which is attached to each helix end with the U sections of the elements interlocked. The coupling is particularly beneficial for interconnecting helical Nitinol elements utilized in thermal actuators or engines. Each coupling half is attached to the associated helix at two points, thereby providing axial load while being easily removed from the helix, and reusable.

  12. Helix coupling

    DOEpatents

    Ginell, William S.

    1989-04-25

    A coupling for connecting helix members in series, which consists of a pair of U-shaped elements, one of which is attached to each helix end with the "U" sections of the elements interlocked. The coupling is particularly beneficial for interconnecting helical Nitinol elements utilized in thermal actuators or engines. Each coupling half is attached to the associated helix at two points, thereby providing axial load while being easily removed from the helix, and reusable.

  13. Living with Hearing Loss

    MedlinePlus

    ... Issues Special Section: Focus on Communication Living with Hearing Loss Past Issues / Fall 2008 Table of Contents For ... Fast Facts There are two main types of hearing loss. Permanent hearing loss (called sensorineural) usually involves damage ...

  14. Early Pregnancy Loss

    MedlinePlus

    ... is called early pregnancy loss , miscarriage , or spontaneous abortion . How common is early pregnancy loss? Early pregnancy ... testes that can fertilize a female egg. Spontaneous Abortion: The medical term for early pregnancy loss. Trimester: ...

  15. Living with vision loss

    MedlinePlus

    Diabetes - vision loss; Retinopathy - vision loss; Low vision; Blindness - vision loss ... Low vision is a visual disability. Wearing regular glasses or contacts does not help. People with low vision have ...

  16. Symmetry properties of the K =0 sup + bands in reflection asymmetric sup 224 Ac

    SciTech Connect

    Sheline, R.K.; Kvasil, J. ); Liang, C.F.; Paris, P. )

    1991-11-01

    Parity doublet bands with {ital K}=0{sup {plus minus}} implying reflection asymmetry (with an average spacing between the levels of the same spin and opposite parity of 12.6 keV) are observed in {sup 224}Ac. In the strong coupling limit all {ital K}=0{sup {plus minus}} parity doublet bands are shown to be constrained to Newby splittings with the same absolute magnitude, but with opposite sign. Experimentally, the Newby splittings in {sup 224}Ac approach this theoretical expectation.

  17. Design and Construction of Test Coils for the MICE Coupling Solenoid Magnet

    SciTech Connect

    Wang, Li; Pan, Heng; Xu, F.Y.; Liu, XioaKun; Chen, AnBin; Li, LanKai; Gou, XingLong; Wu, Hong; Green, Michael; Li, Darun; Strauss, Bruce

    2008-08-08

    The superconducting coupling solenoid to be applied in the Muon Ionization Cooling Experiment (MICE) is made from copper matrix Nb-Ti conductors with inner radius of 750 mm, length of 285 mm and thickness of 102.5 mm at room temperature. The magnetic field up to 2.6 T at the magnet centerline is to keep the muons within the MICE RF cavities. Its self inductance is around 592 H and its magnet stored energy is about 13 MJ at a full current of 210 A for the worst operation case of the MICE channel. The stress induced inside the coil during cool down and charging is relatively high. Two test coils are to build and test in order to validate the design method and develop the fabrication technique required for the coupling coil winding, one is 350 mm inner diameter and full length same as the coupling coil, and the other is one-quarter length and 1.5 m diameter. The 1.5 m diameter coil will be charged to strain conditions that are greater than would be encountered in the coupling coil. This paper presents detailed design of the test coils as well as developed winding skills. The analyses on stress in coil assemblies, AC loss, and quench process are carried out.

  18. Development and characterization of immuno-nanocarriers targeting the cancer stem cell marker AC133.

    PubMed

    Bourseau-Guilmain, E; Béjaud, J; Griveau, A; Lautram, N; Hindré, F; Weyland, M; Benoit, J P; Garcion, E

    2012-02-14

    In the context of targeted therapy, we addressed the possibility of developing a drug delivery nanocarrier capable to specifically reach cancer cells that express the most prominent marker associated with cancer stem cell (CSC) phenotype, AC133. For this purpose, 100nm lipid nanocapsules (LNCs) were functionalized with a monoclonal antibody (mAb) directed against AC133 according to two distinct methods: firstly, post-insertion within 100nm LNCs of a lipid poly(ethylene glycol) functionalized with reactive-sulfhydryl maleimide groups (DSPE-PEG(2000)-maleimide) followed by thiolated mAb coupling, and, secondly, creation of a thiolated lipo-immunoglobulin between DSPE-PEG(2000)-maleimide and AC133, then post-inserted within LNCs. Due to the reduced number of purification steps, lower amounts of DSPE-PEG(2000)-maleimide that were necessary as well as lower number of free maleimide functions present onto the surface of immuno-LNC, the second method was found to be more appropriate. Thus, 126nm AC133-LNC with a zeta potential of -22mV while keeping a narrow distribution were developed. Use of the IgG1κ isotype control-immunoglobulins produced similar control IgG1-LNCs. Micro-Bradford colorimetric assay indicated a fixation of about 40 immunoglobulins per LNC. Use of human Caco-2 cells that constitutively express AC133 (Caco-2-AC133(high)) allowed addressing the behavior of the newly functionalized immuno-LNCs. siRNA knockown strategy permitted to obtain Caco-2-AC133(low) for comparison. Immunofluorescence-combined flow cytometry analysis demonstrated that the epitope-recognition function of AC133 antibody was preserved when present on immuno-LNCs. Although grafting of immunoglobulins onto the surface of LNCs repressed their internalization within Caco-2 cells as evaluated by flow cytometry, AC133-specific cellular binding was obtained with AC133-LNC as assessed by computer-assisted fluorescence microscopy. In conclusion, interest of AC133-LNCs as niche carriers is

  19. Optical coupling

    NASA Astrophysics Data System (ADS)

    Bock, J. J.; Gundersen, J.; Lee, A. T.; Richards, P. L.; Wollack, E.

    2009-03-01

    This paper describes contributions to the CMBpol Technology Study Workshop concerning optical coupling structures. These are structures in or near the focal plane which convert the free space wave to a superconducting microstrip on a SI wafer, or to the waveguide input to a HEMT receiver. In addition to an introduction and conclusions by the editor, this paper includes independent contributions by Bock on 'Planar Antenna-Coupled Bolometers for CMB Polarimetry', by Gunderson and Wollack on 'Millimeter-Wave Platlet Feeds', and by Lee on 'Multi-band Dual-Polarization Lens-coupled Planar Antennas for Bolometric CMB polarimetry.'

  20. Physical aspects of magnetic hyperthermia: Low-frequency ac field absorption in a magnetic colloid

    NASA Astrophysics Data System (ADS)

    L. Raikher, Yu.; Stepanov, V. I.

    2014-11-01

    A uniaxially anisotropic superparamagnetic particle suspended in a viscous fluid and subjected to an ac field is considered. Consistently taking into account both internal (Néel) and external (Brownian) magnetic relaxations, a simple expression for the dynamic susceptibility is obtained. This result, with regard to the ac field energy absorption, is compared to the common heuristic approach. This is done for a model polydisperse colloid containing maghemite nanoparticles, which are assumed to posses either bulk or surface magnetic anisotropy. It is shown that viscous losses caused by the particle motion in a fluid matrix make important contribution to the full magnetic response of a ferrocolloid and, thus, its ability to absorb the ac field energy. The obtained exact expression, which takes in both dissipation mechanisms, paves the way to correct optimization of the nanoparticle-mediated heating effect.

  1. A study of some features of ac and dc electric power systems for a space station

    NASA Technical Reports Server (NTRS)

    Hanania, J. I.

    1983-01-01

    This study analyzes certain selected topics in rival dc and high frequency ac electric power systems for a Space Station. The interaction between the Space Station and the plasma environment is analyzed, leading to a limit on the voltage for the solar array and a potential problem with resonance coupling at high frequencies. Certain problems are pointed out in the concept of a rotary transformer, and further development work is indicated in connection with dc circuit switching, special design of a transmission conductor for the ac system, and electric motors. The question of electric shock hazards, particularly at high frequency, is also explored. and a problem with reduced skin resistance and therefore increased hazard with high frequency ac is pointed out. The study concludes with a comparison of the main advantages and disadvantages of the two rival systems, and it is suggested that the choice between the two should be made after further studies and development work are completed.

  2. A. C. losses in the SSC high energy booster dipole magnets

    SciTech Connect

    Jayakumar, R.; Kovachev, V.; Snitchler, G.; Orrell, D.

    1991-06-01

    The baseline design for the SSC High Energy Booster (HEB) has dipole bending magnets with a 50 mm aperture. An analysis of the cryogenic heat load due to A.C. losses generated in the HEB ramp cycle are reported for this magnet. Included in this analysis are losses from superconductor hysteresis, yoke hysteresis, strand eddy currents, and cable eddy currents. The A.C. loss impact of 2.5 {mu}m vs. 6 {mu}m filament conductor is presented. A 60 mm aperture design is also investigated. 8 refs., 3 tabs.

  3. Tevatron optics measurements using an AC dipole

    SciTech Connect

    Miyamoto, R.; Kopp, S.E.; Jansson, A.; Syphers, M.J.; /Fermilab

    2007-06-01

    The AC dipole is a device to study beam optics of hadron synchrotrons. It can produce sustained large amplitude oscillations with virtually no emittance growth. A vertical AC dipole for the Tevatron is recently implemented and a maximum oscillation amplitude of 2{sigma} (4{sigma}) at 980 GeV (150 GeV) is achieved [1]. When such large oscillations are measured with the BPM system of the Tevatron (20 {micro}m resolution), not only linear but even nonlinear optics can be directly measured. This paper shows how to measure {beta} function using an AC dipole and the result is compared to the other measurement. The paper also shows a test to detect optics changes when small changes are made in the Tevatron. Since an AC dipole is nondestructive, it allows frequent measurements of the optics which is necessary for such an test.

  4. The AC-120: The advanced commercial transport

    NASA Technical Reports Server (NTRS)

    Duran, David; Griffin, Ernest; Mendoza, Saul; Nguyen, Son; Pickett, Tim; Noernberg, Clemm

    1993-01-01

    The main objective of this design was to fulfill a need for a new airplane to replace the aging 100 to 150 passenger, 1500 nautical mile range aircraft such as the Douglas DC9 and Boeing 737-100 airplanes. After researching the future aircraft market, conducting extensive trade studies, and analysis on different configurations, the AC-120 Advanced Commercial Transport final design was achieved. The AC-120's main design features include the incorporation of a three lifting surface configuration which is powered by two turboprop engines. The AC-120 is an economically sensitive aircraft which meets the new FM Stage Three noise requirements, and has lower NO(x) emissions than current turbofan powered airplanes. The AC-120 also improves on its contemporaries in passenger comfort, manufacturing, and operating cost.

  5. New ACS Guidelines Approved by CPT

    NASA Astrophysics Data System (ADS)

    Polik, William F.; Larive, Cynthia K.

    2008-04-01

    The American Chemical Society (ACS) Guidelines for Bachelor's Degree Programs have been revised in 2008 by the Committee on Professional Training (CPT) to reflect changes that are occurring in the chemistry profession and chemistry education. The goals of these changes are to promote modern and innovative chemistry curricula, encourage pedagogical innovation that enhances student learning and success, define faculty and infrastructure attributes of excellent chemistry programs, and streamline the procedures for program approval and review by ACS. The curriculum guidelines for an ACS-certified bachelor's degree are described in terms of foundation coursework, in-depth coursework, and laboratory requirements. Chemistry departments are encouraged to develop degree tracks to target emerging areas of interest within chemistry. The importance of developing student skills and regular program self-evaluation is emphasized. Finally, the procedures for approving and reviewing chemistry programs by ACS are summarized.

  6. Hair loss in women.

    PubMed

    Harfmann, Katya L; Bechtel, Mark A

    2015-03-01

    Hair loss is a common cause of morbidity for many women. As a key member of the woman's health care team, the obstetrician/gynecologist may be the first person to evaluate the complaint of hair loss. Common types of nonscarring hair loss, including female pattern hair loss and telogen effluvium, may be diagnosed and managed by the obstetrician/gynecologist. A systematic approach to diagnosis and management of these common forms of hair loss is presented. PMID:25517757

  7. Energy loss rate in disordered quantum well

    SciTech Connect

    Tripathi, P.; Ashraf, S. S. Z.; Hasan, S. T.; Sharma, A. C.

    2014-04-24

    We report the effect of dynamically screened deformation potential on the electron energy loss rate in disordered semiconductor quantum well. Interaction of confined electrons with bulk acoustic phonons has been considered in the deformation coupling. The study concludes that the dynamically screened deformation potential coupling plays a significant role as it substantially affects the power dependency of electron relaxation on temperature and mean free path.

  8. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  9. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  10. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  11. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  12. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  13. ChAcNLS, a Novel Modification to Antibody-Conjugates Permitting Target Cell-Specific Endosomal Escape, Localization to the Nucleus, and Enhanced Total Intracellular Accumulation.

    PubMed

    Beaudoin, Simon; Rondeau, Andreanne; Martel, Olivier; Bonin, Marc-Andre; van Lier, Johan E; Leyton, Jeffrey V

    2016-06-01

    The design of antibody-conjugates (ACs) for delivering molecules for targeted applications in humans has sufficiently progressed to demonstrate clinical efficacy in certain malignancies and reduced systemic toxicity that occurs with standard nontargeted therapies. One area that can advance clinical success for ACs will be to increase their intracellular accumulation. However, entrapment and degradation in the endosomal-lysosomal pathway, on which ACs are reliant for the depositing of their molecular payload inside target cells, leads to reduced intracellular accumulation. Innovative approaches that can manipulate this pathway may provide a strategy for increasing accumulation. We hypothesized that escape from entrapment inside the endosomal-lysosomal pathway and redirected trafficking to the nucleus could be an effective approach to increase intracellular AC accumulation in target cells. Cholic acid (ChAc) was coupled to the peptide CGYGPKKKRKVGG containing the nuclear localization sequence (NLS) from SV-40 large T-antigen, which is termed ChAcNLS. ChAcNLS was conjugated to the mAb 7G3 (7G3-ChAcNLS), which has nanomolar affinity for the cell-surface leukemic antigen interleukin-3 receptor-α (IL-3Rα). Our aim was to determine whether 7G3-ChAcNLS increased intracellular accumulation while retaining nanomolar affinity and IL-3Rα-positive cell selectivity. Competition ELISA and cell treatment assays were performed. Cell fractionation, confocal microscopy, flow cytometry, and Western blot techniques were used to determine the level of antibody accumulation inside cells and in corresponding nuclei. In addition, the radioisotope copper-64 ((64)Cu) was also utilized as a surrogate molecular cargo to evaluate nuclear and intracellular accumulation by radioactivity counting. 7G3-ChAcNLS effectively escaped endosome entrapment and degradation resulting in a unique intracellular distribution pattern. mAb modification with ChAcNLS maintained 7G3 nM affinity and produced high

  14. Pixel-based CTE Correction of ACS/WFC: Potential Benefits from Charge Injection

    NASA Astrophysics Data System (ADS)

    Golimowski, David A.; Anderson, J.; Smith, L. J.; MacKenty, J.; Cheng, E.; Waczynski, A.; Graham, E.; Wilson, E.; Mazzuca, L.; Loose, M.

    2012-01-01

    The implementation of charge injection (CI) as a means of mitigating charge transfer inefficiency (CTI) in HST's WFC3/UVIS channel has inspired us to study the possible use of CI with HST's ACS/WFC channel and its potential benefit to subsequent CTI correction with the pixel-based algorithm of Anderson & Bedin. We have achieved substantial CTI mitigation in the laboratory using both continuous and discrete line injection modes of CI with an irradiated engineering-grade ACS/WFC CCD. Although the mitigation and noise characteristics of the line injection are favorable for scientific use in the regime of very low natural sky background (< 10 e-/pix) as is prevalent in WFC3/UVIS exposures, line injection is not practical for the vast majority of ACS/WFC science exposures, which have backgrounds of 40-150 e-/pix. Moreover, the short average release time of ACS/WFC charge traps precludes uniform mitigation in the interline regions and significantly complicates science data analysis. On the other hand, a continuous injection (or "flood") of several hundred electrons with noise ≤ 7 e- would uniformly limit CTI to 20% at all signal levels and pixel locations while only minimally affecting the signal-to-noise ratios of the sources. Such CTI losses could subsequently be corrected by the pixel-based algorithm to better than 5%. If such CI is achievable, it could become the default operating mode for ACS exposures in future observing cycles.

  15. Lossy Compression of ACS images

    NASA Astrophysics Data System (ADS)

    Cox, Colin

    2004-01-01

    A method of compressing images stored as floating point arrays was proposed several years ago by White and Greenfield. With the increased image sizes encountered in the last few years and the consequent need to distribute large data volumes, the value of applying such a procedure has become more evident. Methods such as this which offer significant compression ratios are lossy and there is always some concern that statistically important information might be discarded. Several astronomical images have been analyzed and, in the examples tested, compression ratios of about six were obtained with no significant information loss.

  16. Climate Chemistry Coupling: Ozone Loss Linked to the Unique Dynamical Structure of the Summertime Stratosphere Over the U.S. Using In Situ Aircraft, Satellite and NEXRAD Radar Observations

    NASA Astrophysics Data System (ADS)

    Anderson, J. G.; Wilmouth, D. M.; Smith, J. B.; Dykema, J. A.; Leroy, S. S.; Koby, T.; Clapp, C.; Bowman, K. P.

    2015-12-01

    A remarkable combination of meteorological and catalytic chemical factors place the summertime lower stratosphere over the U.S. in a unique position at the intersection of climate forcing and potential ozone loss in the stratosphere. The factors that conspire to establish this circumstance engages four independent considerations. First is the occurrence of severe storms in the U.S. Mid-West caused by the intersection of moist airflow from the Gulf of Mexico with airflow from higher latitudes in spring and summer. These storms are characterized by a combination of tornadoes, hail, heavy precipitation and high winds, the frequency and intensity of which are increasing with increased forcing of the climate system by the addition of CO2, CH4, N2O CFCs, and other infrared active species to the atmosphere associated with human activity. Second is the recognition that these severe storms are capable of injecting water vapor deep into the stratosphere over the U.S., with injection depths reaching the altitude of increasing inorganic halogen species formed by the photolytic breakdown of organic chorine and bromine transported into the stratosphere. Third is the recognition that the catalytic conversion of inorganic halogen species to radicals, specifically ClO and BrO, that are the rate limiting catalytic species that destroy ozone, occurs on ubiquitous sulfate-water aerosols wherever and whenever the temperature-water vapor conditions are met. These conditions are met in the Antarctic and Arctic winter vortices by virtue of temperatures below 200K at 5 ppmv water vapor, and in the summertime lower stratosphere over the U.S. by virtue of temperatures between 200 and 205K in combination with convectively injected water vapor concentrations in the range of 8 ppmv or greater. Fourth, is the recognition that the flow pattern of the lower stratosphere over the U.S. in summer is repeatedly under the control of the North American monsoon that forms an anti-cyclonic (clockwise

  17. QCD Collisional Energy Loss Reexamined

    NASA Astrophysics Data System (ADS)

    Peshier, A.

    2006-11-01

    It is shown that at a large temperature and E→∞ the QCD collisional energy loss reads dE/dx˜α(mD2)T2. Compared to previous approaches, which led to dEB/dx˜α2T2ln⁡(ET/mD2) similar to the Bethe-Bloch formula in QED, we take into account the running of the strong coupling. As one significant consequence, due to asymptotic freedom, dE/dx becomes E independent for large parton energies. Some implications with regard to heavy ion collisions are pointed out.

  18. QCD collisional energy loss reexamined.

    PubMed

    Peshier, A

    2006-11-24

    It is shown that at a large temperature and E --> infinity the QCD collisional energy loss reads dE/dx approximately alpha(m(D)2)T2. Compared to previous approaches, which led to dE(B)/dx approximately alpha2 T2 ln(ET/m(D)2) similar to the Bethe-Bloch formula in QED, we take into account the running of the strong coupling. As one significant consequence, due to asymptotic freedom, dE/dx becomes E independent for large parton energies. Some implications with regard to heavy ion collisions are pointed out. PMID:17155739

  19. TRF2 and lamin A/C interact to facilitate the functional organization of chromosome ends

    PubMed Central

    Wood, Ashley M.; Danielsen, Jannie M. Rendtlew; Lucas, Catherine A.; Rice, Ellen L.; Scalzo, David; Shimi, Takeshi; Goldman, Robert D.; Smith, Erica D.; Le Beau, Michelle M.; Kosak, Steven T.

    2014-01-01

    Telomeres protect the ends of linear genomes, and the gradual loss of telomeres is associated with cellular ageing. Telomere protection involves the insertion of the 3′ overhang facilitated by telomere repeat-binding factor 2 (TRF2) into telomeric DNA, forming t-loops. We present evidence suggesting that t-loops can also form at interstitial telomeric sequences in a TRF2-dependent manner, forming an interstitial t-loop (ITL). We demonstrate that TRF2 association with interstitial telomeric sequences is stabilized by co-localization with A-type lamins (lamin A/C). We also find that lamin A/C interacts with TRF2 and that reduction in levels of lamin A/C or mutations in LMNA that cause an autosomal dominant premature ageing disorder—Hutchinson Gilford Progeria Syndrome (HGPS)—lead to reduced ITL formation and telomere loss. We propose that cellular and organismal ageing are intertwined through the effects of the interaction between TRF2 and lamin A/C on chromosome structure. PMID:25399868

  20. Development of an Nb{sub 3}Sn AC coil with react and wind method

    SciTech Connect

    Kasahara, H.; Torii, S.; Akita, S.; Kubota, Y.; Yasohama, K.; Kobayashi, H.; Ogasawara, T.; Kumano, T.; Miyake, S.

    1996-07-01

    The Nb{sub 3}Sn superconductor possesses a higher critical temperature than the NbTi strand. Therefore, it is now possible to make highly stable superconducting strands. The authors examined the manufacturing process of AC Nb{sub 3}Sn strands. The internal Sn diffusion process showed a higher critical current density than the conventional process. Nb{sub 3}Sn strands for AC use have a high Jc with low temperature reaction heat treatment, because they have fine filaments to decrease AC loss. They made a 400kVA class superconducting coil using the developed Nb{sub 3}Sn cable with the React and Wind method. The loss density of this coil was 25.7MW/m{sup 3} at the point just before the quench. In this case, the temperature of the cable increases about 3.39K. This means that the coil using Nb{sub 3}Sn cables has a very high stability in AC use.

  1. Electromechanical systems with transient high power response operating from a resonant AC link

    NASA Technical Reports Server (NTRS)

    Burrows, Linda M.; Hansen, Irving G.

    1992-01-01

    The combination of an inherently robust asynchronous (induction) electrical machine with the rapid control of energy provided by a high frequency resonant AC link enables the efficient management of higher power levels with greater versatility. This could have a variety of applications from launch vehicles to all-electric automobiles. These types of systems utilize a machine which is operated by independent control of both the voltage and frequency. This is made possible by using an indirect field-oriented control method which allows instantaneous torque control in all four operating quadrants. Incorporating the AC link allows the converter in these systems to switch at the zero crossing of every half cycle of the AC waveform. This zero loss switching of the link allows rapid energy variations to be achieved without the usual frequency proportional switching loss. Several field-oriented control systems were developed by LeRC and General Dynamics Space Systems Division under contract to NASA. A description of a single motor, electromechanical actuation system is presented. Then, focus is on a conceptual design for an AC electric vehicle. This design incorporates an induction motor/generator together with a flywheel for peak energy storage. System operation and implications along with the associated circuitry are addressed. Such a system would greatly improve all-electric vehicle ranges over the Federal Urban Driving Cycle (FUD).

  2. Experimental AC (Asphalt Concrete) overlays of PCC pavement

    NASA Astrophysics Data System (ADS)

    Smith, R. D.

    1983-11-01

    A series of experimental asphalt concrete (AC) overlays was constructed over an existing distressed portland cement concrete pavement on Interstate 80 near Boca, California. The experimental overlays included rubberized dense-graded AC, rubberized open-graded AC, a rubber flush coat interlayer, dense-graded AC with short polyester fibers and Bituthene interlayer strips. The report presents a description and discussion of AC mix batching, construction observations, laboratory testing, overlay covering, and initial performance evaluation.

  3. Perfecting the Photometric Calibration of the ACS CCD Cameras

    NASA Astrophysics Data System (ADS)

    Bohlin, Ralph C.

    2016-09-01

    Newly acquired data and improved data reduction algorithms mandate a fresh look at the absolute flux calibration of the charge-coupled device cameras on the Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS). The goals are to achieve a 1% accuracy and to make this calibration more accessible to the HST guest investigator. Absolute fluxes from the CALSPEC1 database for three primary hot 30,000–60,000K WDs define the sensitivity calibrations for the Wide Field Channel (WFC) and High Resolution Channel (HRC) filters. The external uncertainty for the absolute flux is ∼1%, while the internal consistency of the sensitivities in the broadband ACS filters is ∼0.3% among the three primary WD flux standards. For stars as cool as K type, the agreement with the CALSPEC standards is within 1% at the WFC1-1K subarray position, which achieves the 1% precision goal for the first time. After making a small adjustment to the filter bandpass for F814W, the 1% precision goal is achieved over the full F814W WFC field of view for stars of K type and hotter. New encircled energies and absolute sensitivities replace the seminal results of Sirianni et al. that were published in 2005. After implementing the throughput updates, synthetic predictions of the WFC and HRC count rates for the average of the three primary WD standard stars agree with the observations to 0.1%.

  4. Testing of a First Order AC Magnetic Susceptometer

    NASA Astrophysics Data System (ADS)

    Fukuda, Ryan; Sunny, Smitha; Ho, Pei-Chun

    2011-11-01

    A first-order AC magnetic susceptometer has been constructed and tested to find the magnetic response of strongly correlated electron materials. The instrument works by using a primary coil to apply a small AC magnetic field of .104 Oe to a sample with a cylindrical coil space of length .635 cm and diameter .355 cm. A lock-in amplifier is used to monitor the induced voltage from a set of secondary coils. By coupling a temperature-controlled system with this instrument, the change in the magnetic signal with respect to temperature is measured. Monitoring the signal changes may indicate the temperature that causes the material to transition to either a ferromagnetic, anti-ferromagnetic, or superconducting state. A 122.47 mg Gd polycrystal was used to test our susceptometer. The data qualitatively agrees with the previous results of magnetization vs. temperature of Gd single crystals by Nigh et al. [1]: there is a steep increase in the pick-up signal at 300 K where Gd becomes ferromagnetic and a peak at 210 K [1]. This susceptometer will be used for our future investigation of magnetic properties of rare earth compounds and nanoparticles in the temperature range of 10 K to 300 K. [4pt] [1] H. E. Nigh, S. Legvold, and F. H. Spedding, Physical Review 132, 1092 (1963)

  5. Perfecting the Photometric Calibration of the ACS CCD Cameras

    NASA Astrophysics Data System (ADS)

    Bohlin, Ralph C.

    2016-09-01

    Newly acquired data and improved data reduction algorithms mandate a fresh look at the absolute flux calibration of the charge-coupled device cameras on the Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS). The goals are to achieve a 1% accuracy and to make this calibration more accessible to the HST guest investigator. Absolute fluxes from the CALSPEC1 database for three primary hot 30,000–60,000K WDs define the sensitivity calibrations for the Wide Field Channel (WFC) and High Resolution Channel (HRC) filters. The external uncertainty for the absolute flux is ˜1%, while the internal consistency of the sensitivities in the broadband ACS filters is ˜0.3% among the three primary WD flux standards. For stars as cool as K type, the agreement with the CALSPEC standards is within 1% at the WFC1-1K subarray position, which achieves the 1% precision goal for the first time. After making a small adjustment to the filter bandpass for F814W, the 1% precision goal is achieved over the full F814W WFC field of view for stars of K type and hotter. New encircled energies and absolute sensitivities replace the seminal results of Sirianni et al. that were published in 2005. After implementing the throughput updates, synthetic predictions of the WFC and HRC count rates for the average of the three primary WD standard stars agree with the observations to 0.1%.

  6. Turbo code carrier synchronization losses (Radio Losses)

    NASA Technical Reports Server (NTRS)

    Shanibayati, Shervin; Kinman, Peter; Tadjpour, Layla

    2001-01-01

    In this paper the radio loss results for (8920,1/3), (8920,1/6), (1783,1/3) and (1784,1/6) codes are presented. These radio losses were calculated through simulations for a range of data rates. These simulations included both suppressed carrier modulation and residual carrier modulation cases. The radio losses were calculated for a frame error rate of 3 x 10^-4 for (8920,1/3) and (8920,1/6) codes and 3 frame error rate of 6 x 10^-5 for (1764,1/3) and (1784,1/6) codes. The simulations for the residual carrier case were run for loop signal to noise ratios of 13dB, 15dB and 17dB with a loop bandwidth of 10Hz. The simulations for the suppressed carrier case were run for a loop of signal to noise ratio of 17dB. The results of these simulations indicate that the radio losses for turbo codes are low enough to warrant their use in deep space links (maximum of 1dB loss at 17dB loop signal to noise ratio for residual carrier and 1.3dB loss at 17dB loop signal to noise ratio for suppressed carrier at high data rates). Furthermore, these results indicate that by normalizing the radio losses for frame size, loop bandwidth and the loop signal to noise ratio, a single curve could be used for calculating the radio loss for any given data rate at any given loop signal to noise ratio.

  7. Genetic Causes of Recurrent Pregnancy Loss.

    PubMed

    Page, Jessica M; Silver, Robert M

    2016-09-01

    Pregnancy loss is one of the most common obstetric complications, affecting over 30% of conceptions. A considerable proportion of losses are due to genetic abnormalities. Indeed, over 50% of early pregnancy losses have been associated with chromosomal abnormalities. Most are due to de novo nondisjunctional events but balanced parental translocations are responsible for a small but important percentage of genetic abnormalities in couples with recurrent pregnancy loss. In the past, assessment of genetic abnormalities was limited to karyotype performed on placental or fetal tissue. However, advances in molecular genetic technology now provide rich genetic information about additional genetic causes of and risk factors for pregnancy loss. In addition, the use of preimplantation genetic testing in couples undergoing in vitro fertilization has the potential to decrease the risk of pregnancy loss from genetic abnormalities. To date, efficacy is uncertain but considerable potential remains. This chapter will review what is known about genetic causes of recurrent pregnancy loss with a focus on novel causes and potential treatments. Remaining knowledge gaps will be highlighted. PMID:27414972

  8. Four-piston double-duct liquid metal MHD engine and AC generator

    SciTech Connect

    Haaland, C.M.

    1995-12-31

    Operating principles, features and applications of the Liquid Metal (LM) engine are presented. This engine combines a free-piston internal combustion engine with an MHD AC power generator. Liquid metal (LM) oscillates back-and-forth in two separate channels, driven by free pistons coupled magnetically to pistons driven by internal combustion. One of the principal breakthroughs is the concept of using double ducts in a Hartmann configuration for MHD production of alternating current. The LM flows in opposing directions in the two adjacent Hartmann ducts, thus eliminating magnetic-induced instabilities, eliminating vibration, and providing an ideal setup for attaching an output transformer on one side provide to provide useful ranges of current and voltage. Because LM is used, the length of the piston stroke can be easily varied over a large range, thus making possible an engine that, changes size, according to variation in output load requirements. Increasing the stroke length results in increased compression ratio, which requires computer controlled modification of the fuel injection mixture. Higher fuel efficiencies will result, whether the engine is idling or operating at maximum power. Because of viscous dissipation losses in the LM, this engine will be more efficient for larger engines. Applications include any power generation where variable load is required, such as stationary electric generators for remote towns and cities, temporary military encampments, and mobile primary power generators for off-road and on-road automotive equipment, including caterpillars, cars, military vehicles, trucks, and trains. The advantages for automotive propulsion will be described in comparisons with current and developmental vehicles using internal combustion engines. Because the LM-engine generates electricity, an LM-engine vehicle is readily adaptable to hybrid concepts. An R&D program will be outlined for bringing the concept of the LM engine to commercial application.

  9. AC conductivity and dielectric behavior of CoAl xFe 2- xO 4

    NASA Astrophysics Data System (ADS)

    Abo El Ata, A. M.; Attia, S. M.; Meaz, T. M.

    2004-01-01

    AC conductivity and dielectric properties have been studied for a series of polycrystalline spinel ferrite with composition CoAl xFe 2- xO 4, as a function of frequency and temperature. The results of AC conductivity were discussed in terms of the quantum mechanical tunneling and small polaron tunneling models. The dispersion of the dielectric constant was discussed in the light of Koops model and hopping conduction mechanism. The dielectric loss tangent tan δ curves exhibits a dielectric relaxation peaks which are attributed to the coincidence of the hopping frequency of the charge carriers with that of the external fields. The AC conductivity, dielectric constant, and dielectric loss tangent were found to increase with increasing the temperature due to the increase of the hopping frequency, while they decrease with increasing Al ion content due to the reduction of iron ions available for the conduction process at the octahedral sites.

  10. Prosthesis coupling

    NASA Technical Reports Server (NTRS)

    Reswick, J. B.; Mooney, V.; Bright, C. W.; Owens, L. J. (Inventor)

    1979-01-01

    A coupling for use in an apparatus for connecting a prosthesis to the bone of a stump of an amputated limb is described which permits a bio-compatible carbon sleeve forming a part of the prosthesis connector to float so as to prevent disturbing the skin seal around the carbon sleeve. The coupling includes a flexible member interposed between a socket that is inserted within an intermedullary cavity of the bone and the sleeve. A lock pin is carried by the prosthesis and has a stem portion which is adapted to be coaxially disposed and slideably within the tubular female socket for securing the prosthesis to the stump. The skin around the percutaneous carbon sleeve is able to move as a result of the flexing coupling so as to reduce stresses caused by changes in the stump shape and/or movement between the bone and the flesh portion of the stump.

  11. FLEXIBLE COUPLING

    DOEpatents

    Babelay, E.F.

    1962-02-13

    A flexible shaft coupling for operation at speeds in excess of 14,000 rpm is designed which requires no lubrication. A driving sleeve member and a driven sleeve member are placed in concentric spaced relationship. A torque force is transmitted to the driven member from the driving member through a plurality of nylon balls symmetrically disposed between the spaced sleeves. The balls extend into races and recesses within the respective sleeve members. The sleeve members have a suitable clearance therebetween and the balls have a suitable radial clearance during operation of the coupling to provide a relatively loose coupling. These clearances accommodate for both parallel and/or angular misalignments and avoid metal-tometal contact between the sleeve members during operation. Thus, no lubrication is needed, and a minimum of vibrations is transmitted between the sleeve members. (AEC)

  12. Weight-loss medications

    MedlinePlus

    ... this page: //medlineplus.gov/ency/patientinstructions/000346.htm Weight-loss medicines To use the sharing features on this page, please enable JavaScript. Several weight-loss medicines are available. Ask your health care provider ...

  13. Weight Loss & Acute Porphyria

    MedlinePlus

    ... Sale You are here Home Diet and Nutrition Weight loss & acute Porphyria Being overweight is a particular problem ... one of these diseases before they enter a weight-loss program. Also, they should not participate in a ...

  14. Living with hearing loss

    MedlinePlus

    ... medlineplus.gov/ency/patientinstructions/000360.htm Living with hearing loss To use the sharing features on this page, please enable JavaScript. If you are living with hearing loss, you know that it takes extra effort to ...

  15. Hearing Loss: Screening Newborns

    MedlinePlus

    ... of this page please turn JavaScript on. Feature: Hearing Loss Screening Newborns Past Issues / Spring 2015 Table of ... of newborns in the U.S. are screened for hearing loss before they leave the hospital. Research improves the ...

  16. Loss and Recovery

    NASA Technical Reports Server (NTRS)

    Schwer, Ken

    2002-01-01

    The author recounts his experiences of the loss of the QuickTOMS (Total Ozone Mapping Spectrometer) spacecraft, for which he was project manager. He draws from the launch failure lessons on leadership, coping with loss and maintaining morale.

  17. Photovoltaic array loss mechanisms

    NASA Technical Reports Server (NTRS)

    Gonzalez, Charles

    1986-01-01

    Loss mechanisms which come into play when solar cell modules are mounted in arrays are identified. Losses can occur either from a reduction in the array electrical performance or with nonoptimal extraction of power from the array. Electrical performance degradation is caused by electrical mismatch, transmission losses from cell surface soiling and steep angle of reflectance, and electrical losses from field wiring resistance and the voltage drop across blocking diodes. The second type of loss, concerned with the operating points of the array, can involve nonoptimal load impedance and limiting the operating envelope of the array to specific ranges of voltage and current. Each of the loss mechanisms are discussed and average energy losses expected from soiling, steep reflectance angles and circuit losses are calculated.

  18. Genetics of Hearing Loss

    MedlinePlus

    ... in Latin America Information For... Media Policy Makers Genetics of Hearing Loss Language: English Español (Spanish) Recommend ... of hearing loss in babies is due to genetic causes. There are also a number of things ...

  19. Genes and Hearing Loss

    MedlinePlus

    ... Meeting Calendar Find an ENT Doctor Near You Genes and Hearing Loss Genes and Hearing Loss Patient ... mutation may only have dystopia canthorum. How Do Genes Work? Genes are a road map for the ...

  20. Direct measurements of Ab and Ac using vertex and kaon charge tags at the SLAC detector.

    PubMed

    Abe, Koya; Abe, Kenji; Abe, T; Adam, I; Akimoto, H; Aston, D; Baird, K G; Baltay, C; Band, H R; Barklow, T L; Bauer, J M; Bellodi, G; Berger, R; Blaylock, G; Bogart, J R; Bower, G R; Brau, J E; Breidenbach, M; Bugg, W M; Burke, D; Burnett, T H; Burrows, P N; Calcaterra, A; Cassell, R; Chou, A; Cohn, H O; Coller, J A; Convery, M R; Cook, V; Cowan, R F; Crawford, G; Damerell, C J S; Daoudi, M; Dasu, S; de Groot, N; de Sangro, R; Dong, D N; Doser, M; Dubois, R; Erofeeva, I; Eschenburg, V; Etzion, E; Fahey, S; Falciai, D; Fernandez, J P; Flood, K; Frey, R; Hart, E L; Hasuko, K; Hertzbach, S S; Huffer, M E; Huynh, X; Iwasaki, M; Jackson, D J; Jacques, P; Jaros, J A; Jiang, Z Y; Johnson, A S; Johnson, J R; Kajikawa, R; Kalelkar, M; Kang, H J; Kofler, R R; Kroeger, R S; Langston, M; Leith, D W G; Lia, V; Lin, C; Mancinelli, G; Manly, S; Mantovani, G; Markiewicz, T W; Maruyama, T; McKemey, A K; Messner, R; Moffeit, K C; Moore, T B; Morii, M; Muller, D; Murzin, V; Narita, S; Nauenberg, U; Neal, H; Nesom, G; Oishi, N; Onoprienko, D; Osborne, L S; Panvini, R S; Park, C H; Peruzzi, I; Piccolo, M; Piemontese, L; Plano, R J; Prepost, R; Prescott, C Y; Ratcliff, B N; Reidy, J; Reinertsen, P L; Rochester, L S; Rowson, P C; Russell, J J; Saxton, O H; Schalk, T; Schumm, B A; Schwiening, J; Serbo, V V; Shapiro, G; Sinev, N B; Snyder, J A; Staengle, H; Stahl, A; Stamer, P; Steiner, H; Su, D; Suekane, F; Sugiyama, A; Suzuki, A; Swartz, M; Taylor, F E; Thom, J; Torrence, E; Usher, T; Va'vra, J; Verdier, R; Wagner, D L; Waite, A P; Walston, S; Weidemann, A W; Weiss, E R; Whitaker, J S; Williams, S H; Willocq, S; Wilson, R J; Wisniewski, W J; Wittlin, J L; Woods, M; Wright, T R; Yamamoto, R K; Yashima, J; Yellin, S J; Young, C C; Yuta, H

    2005-03-11

    Exploiting the manipulation of the SLAC Linear Collider electron-beam polarization, we present precise direct measurements of the parity-violation parameters A(c) and A(b) in the Z-boson-c-quark and Z-boson-b-quark coupling. Quark-antiquark discrimination is accomplished via a unique algorithm that takes advantage of the precise SLAC Large Detector charge coupled device vertex detector, employing the net charge of displaced vertices as well as the charge of kaons that emanate from those vertices. From the 1996-1998 sample of 400 000 Z decays, produced with an average beam polarization of 73.4%, we find A(c)=0.673+/-0.029(stat)+/-0.023(syst) and A(b)=0.919+/-0.018(stat)+/-0.017(syst). PMID:15783953

  1. Enhanced loading efficiency and retention of 225Ac in rigid liposomes for potential targeted therapy of micrometastases.

    PubMed

    Chang, Min-Yuan; Seideman, Jonathan; Sofou, Stavroula

    2008-06-01

    Targeted alpha-particle emitters are promising therapeutics for micrometastatic disease. Actinium-225 has a 10-day half-life and generates a total of four alpha-particles per parent decay rendering (225)Ac an attractive candidate for alpha-therapy. For cancer cells with low surface expression levels of molecular targets, targeting strategies of (225)Ac using radiolabeled carriers of low specific radioactivities (such as antibodies) may not deliver enough alpha-particle emitters at the targeted cancer cells to result in killing. We previously proposed and showed using passive (225)Ac entrapment that liposomes can stably retain encapsulated (225)Ac for long time periods, and that antibody-conjugated liposomes (immunoliposomes) with encapsulated (225)Ac can specifically target and become internalized by cancer cells. However, to enable therapeutic use of (225)Ac-containing liposomes, high activities of (225)Ac need to be stably encapsulated into liposomes. In this study, various conditions for active loading of (225)Ac in preformed liposomes (ionophore-type, encapsulated buffer solution, and loading time) were evaluated, and liposomes with up to 73 +/- 9% of the initial activity of (225)Ac (0.2-200 microCi) were developed. Retention of radioactive contents by liposomes was evaluated at 37 degrees C in phosphate buffer and in serum-supplemented media. The main fraction of released (225)Ac from liposomes occurs within the first two hours of incubation. Beyond this two hour point, the encapsulated radioactivity is released from liposomes slowly with an approximate half-life of the order of several days. In some cases, after 30 days, (225)Ac retention as high as 81 +/- 7% of the initially encapsulated radioactivity was achieved. The (225)Ac loading protocol was also applied to immunoliposome loading without significant loss of targeting efficacy. Liposomes with surface-conjugated antibodies that are loaded with (225)Ac overcome the limitations of low specific activity for

  2. Proven Weight Loss Methods

    MedlinePlus

    Fact Sheet Proven Weight Loss Methods What can weight loss do for you? Losing weight can improve your health in a number of ways. It can lower ... at www.hormone.org/Spanish . Proven Weight Loss Methods Fact Sheet www.hormone.org

  3. Hearing loss in space

    NASA Technical Reports Server (NTRS)

    Buckey, J. C. Jr; Musiek, F. E.; Kline-Schoder, R.; Clark, J. C.; Hart, S.; Havelka, J.

    2001-01-01

    BACKGROUND: Temporary and, in some cases, permanent hearing loss has been documented after long-duration spaceflights. METHODS: We examined all existing published data on hearing loss after space missions to characterize the losses. RESULTS: Data from Russian missions suggest that the hearing loss, when it occurs, affects mainly mid to high frequencies and that using hearing protection often might prevent the loss. Several significant questions remain about hearing loss in space. While the hearing loss has been presumed to be noise-induced, no clear link has been established between noise exposure and hearing loss during spaceflight. In one documented case of temporary hearing loss from the Shuttle-Mir program, the pattern of loss was atypical for a noise-induced loss. Continuous noise levels that have been measured on the Mir and previous space stations, while above engineering standards, are not at levels usually associated with hearing loss in ground-based studies (which have usually been limited to 8-10 h exposure periods). Attempts to measure hearing in space using threshold-based audiograms have been unsuccessful in both the American and Russian programs due to noise interference with the measurements. CONCLUSIONS: The existing data highlight the need for reliable monitoring of both hearing and noise in long-duration spaceflight.

  4. Sexuality Following the Loss of a Child

    ERIC Educational Resources Information Center

    Dyregrov, Atle; Gjestad, Rolf

    2011-01-01

    The aim of study was to increase our understanding of sexuality and intimacy following the loss of a child. A questionnaire on intimacy and sexuality was sent to 1,027 members of the 2 major bereavement support organizations for parents who have lost children in Norway. A total of 321 (33%) were returned. In addition, 10 couples were interviewed…

  5. Cyclotron and linac production of Ac-225.

    PubMed

    Melville, Graeme; Allen, Barry J

    2009-04-01

    Radium needles that were once implanted into tumours as a cancer treatment are now obsolete and constitute a radioactive waste problem, as their half-life is 1600 years. The reduction of radium by photonuclear transmutation by bombarding Ra-226 with high-energy photons from a medical linear accelerator (linac) has been investigated. A linac dose of 2800 Gy produced about 2.4 MBq (64 microCi) of Ra-225, which decays to Ac-225 and can then be used for 'Targeted Alpha Therapy' (TAT) of cancer. This result, while consistent with theoretical calculations, is far too low to be of practical use unless much larger quantities of radium are irradiated. The increasing application of Ac-225 for cancer therapy indicates the potential need for its increased production and availability. This paper investigates the possibility of producing of Ac-225 in commercial quantities, which could potentially reduce obsolete radioactive material and displace the need for expensive importation of Ac-225 from the USA and Russia in the years ahead. Scaled up production of Ac-225 could theoretically be achieved by the use of a high current cyclotron or linac. Production specifications are determined for a linac in terms of current, pulse length and frequency, as well as an examination of other factors such as radiation issues and radionuclei separation. Yields are compared with those calculated for the Australian National Cyclotron in Sydney. PMID:19135381

  6. Evaporative losses of vacuum-compatible oils through labyrinth seals

    NASA Astrophysics Data System (ADS)

    Anderson, M. J.; Freeman, S.; Roberts, E. W.

    2003-09-01

    Following a literature review to assess the theoretical and experimental methods used to evaluate fluid losses via labyrinth seals, an experimental programme was carried out to measure these losses. A model derived by ESTL provided the best correlation with experimental oil losses and an effusion cell approach was identified as the most appropriate method to assess the effectiveness of labyrinth seals for three space oils, ie Krytox 143AC, Nye 186B and Nye 2001A. The selection of these fluids enabled a relatively wide range of vapour pressures to be investigated in the experimental programme using effusion cells of different geometries. The test results were compared with the ESTL oil evaporation model and it was found that the evaporative losses from Nye 186B and HVAC25/9 were within an order of magnitude of predictions. Losses from Nye 2001a were larger than predictions.

  7. Evolution by gene loss.

    PubMed

    Albalat, Ricard; Cañestro, Cristian

    2016-07-01

    The recent increase in genomic data is revealing an unexpected perspective of gene loss as a pervasive source of genetic variation that can cause adaptive phenotypic diversity. This novel perspective of gene loss is raising new fundamental questions. How relevant has gene loss been in the divergence of phyla? How do genes change from being essential to dispensable and finally to being lost? Is gene loss mostly neutral, or can it be an effective way of adaptation? These questions are addressed, and insights are discussed from genomic studies of gene loss in populations and their relevance in evolutionary biology and biomedicine. PMID:27087500

  8. Electron-energy losses in hemispherical targets

    SciTech Connect

    Aizpurua, J.; Rivacoba, A.; Apell, S.P.

    1996-07-01

    In the framework of classical dielectric theory, the hemispherical geometry is studied. Calculations on surface modes are carried out for isolated Drude-like hemispheres. The convergence of the results with respect to the number of coupled terms in the expressions of the potential is discussed. The electron-energy-loss probability is studied for Al and Ag particles involving this geometry. The surface modes and hence the energy-loss probability are given by coupled expressions, the physical meaning of which is the coupling among multipolar terms, because of the particular geometry. The results obtained here present a good quantitative agreement with experiments in the case of clear surfaces (Ag) and provide a qualitative understanding for the experiments in Al, in terms of the position and impact parameter of the beam. This allows us to set the validity of the dielectric theory for cases that seemed to question it. {copyright} {ital 1996 The American Physical Society.}

  9. ac propulsion system for an electric vehicle

    NASA Technical Reports Server (NTRS)

    Geppert, S.

    1980-01-01

    It is pointed out that dc drives will be the logical choice for current production electric vehicles (EV). However, by the mid-80's, there is a good chance that the price and reliability of suitable high-power semiconductors will allow for a competitive ac system. The driving force behind the ac approach is the induction motor, which has specific advantages relative to a dc shunt or series traction motor. These advantages would be an important factor in the case of a vehicle for which low maintenance characteristics are of primary importance. A description of an EV ac propulsion system is provided, taking into account the logic controller, the inverter, the motor, and a two-speed transmission-differential-axle assembly. The main barrier to the employment of the considered propulsion system in EV is not any technical problem, but inverter transistor cost.

  10. ACS Data Handbook v.6.0

    NASA Astrophysics Data System (ADS)

    Gonzaga, S.; et al.

    2011-03-01

    ACS was designed to provide a deep, wide-field survey capability from the visible to near-IR using the Wide Field Camera (WFC), high resolution imaging from the near-UV to near-IR with the now-defunct High Resolution Camera (HRC), and solar-blind far-UV imaging using the Solar Blind Camera (SBC). The discovery efficiency of ACS's Wide Field Channel (i.e., the product of WFC's field of view and throughput) is 10 times greater than that of WFPC2. The failure of ACS's CCD electronics in January 2007 brought a temporary halt to CCD imaging until Servicing Mission 4 in May 2009, when WFC functionality was restored. Unfortunately, the high-resolution optical imaging capability of HRC was not recovered.

  11. Brazilian Angiostrongylus cantonensis haplotypes, ac8 and ac9, have two different biological and morphological profiles

    PubMed Central

    Monte, Tainá CC; Gentile, Rosana; Garcia, Juberlan; Mota, Ester; Santos, Jeannie N; Maldonado, Arnaldo

    2014-01-01

    Angiostrongylus cantonensis is the etiologic agent of eosinophilic meningoencephalitis in humans. Cases have been recorded in many parts of the world, including Brazil. The aim of this study was to compare the differences in the biology and morphology of two different Brazilian haplotypes of A. : ac8 and ac9. A significantly larger number of L1 larvae eliminated in the faeces of rodents at the beginning of the patent period was observed for ac9 haplotype and compared to the total of L1 larvae eliminated, there was a significant difference between the two haplotypes. The ac9 haplotype showed a significant difference in the proportion of female and male specimens (0.6:1), but the same was not observed for ac8 (1.2:1). The morphometric analysis showed that male and female specimens isolated from ac8 haplotype were significantly larger with respect to body length, oesophagus length, spicule length (male) and distance from the anus to the rear end (female) compared to specimens from ac9. The morphological analysis by light microscopy showed little variation in the level of bifurcations at the lateral rays in the right lobe of the copulatory bursa between the two haplotypes. The biological, morphological and morphometric variations observed between the two haplotypes agree with the observed variation at the molecular level using the cytochrome oxidase subunit I marker and reinforce the possible influence of geographical isolation on the development of these haplotypes. PMID:25591110

  12. Coupling analysis of linear vibration energy harvesting systems

    NASA Astrophysics Data System (ADS)

    Wang, Xu; Liang, Xingyu; Shu, Gequn; Watkins, Simon

    2016-03-01

    This paper has disclosed the relationship of vibration energy harvester performance with dimensionless force factor. Numerical ranges of the dimensionless force factor have been defined for cases of weak, moderate and strong coupling. The relationships of coupling loss factor, dimensionless force factor, critical coupling strength, coupling quotient, electro-mechanical coupling factor, damping loss factor and modal densities have been established in linear vibration energy harvester systems. The new contribution of this paper is to determine a frequency range where the vibration energy harvesting systems are in a weak coupling and the statistical energy analysis is applicable.

  13. AcsA-AcsB: The core of the cellulose synthase complex from Gluconacetobacter hansenii ATCC23769.

    PubMed

    McManus, John B; Deng, Ying; Nagachar, Nivedita; Kao, Teh-hui; Tien, Ming

    2016-01-01

    The gram-negative bacterium, Gluconacetobacter hansenii, produces cellulose of exceptionally high crystallinity in comparison to the cellulose of higher plants. This bacterial cellulose is synthesized and extruded into the extracellular medium by the cellulose synthase complex (CSC). The catalytic component of this complex is encoded by the gene AcsAB. However, several other genes are known to encode proteins critical to cellulose synthesis and are likely components of the bacterial CSC. We have purified an active heterodimer AcsA-AcsB from G. hansenii ATCC23769 to homogeneity by two different methods. With the purified protein, we have determined how it is post-translationally processed, forming the active heterodimer AcsA-AcsB. Additionally, we have performed steady-state kinetic studies on the AcsA-AcsB complex. Finally through mutagenesis studies, we have explored the roles of the postulated CSC proteins AcsC, AcsD, and CcpAx. PMID:26672449

  14. Design and Specification of Optical Bandpass Filters for Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS)

    NASA Technical Reports Server (NTRS)

    Leviton, Douglas B.; Tsevetanov, Zlatan; Woodruff, Bob; Mooney, Thomas A.

    1998-01-01

    Advanced optical bandpass filters for the Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS) have been developed on a filter-by-filter basis through detailed studies which take into account the instrument's science goals, available optical filter fabrication technology, and developments in ACS's charge-coupled-device (CCD) detector technology. These filters include a subset of filters for the Sloan Digital Sky Survey (SDSS) which are optimized for astronomical photometry using today's charge-coupled-devices (CCD's). In order for ACS to be truly advanced, these filters must push the state-of-the-art in performance in a number of key areas at the same time. Important requirements for these filters include outstanding transmitted wavefront, high transmittance, uniform transmittance across each filter, spectrally structure-free bandpasses, exceptionally high out of band rejection, a high degree of parfocality, and immunity to environmental degradation. These constitute a very stringent set of requirements indeed, especially for filters which are up to 90 mm in diameter. The highly successful paradigm in which final specifications for flight filters were derived through interaction amongst the ACS Science Team, the instrument designer, the lead optical engineer, and the filter designer and vendor is described. Examples of iterative design trade studies carried out in the context of science needs and budgetary and schedule constraints are presented. An overview of the final design specifications for the ACS bandpass and ramp filters is also presented.

  15. Functional Visual Loss

    PubMed Central

    Bruce, Beau B; Newman, Nancy J

    2010-01-01

    Synopsis Neurologists frequently evaluate patients complaining of vision loss, especially when the patient has been examined by an ophthalmologist who has found no ocular disease. A significant proportion of patients presenting to the neurologist with visual complaints will have non-organic or functional visual loss. While there are examination techniques which can aid in the detection and diagnosis of functional visual loss, the frequency with which functional visual loss occurs concomitantly with organic disease warrants substantial caution on the part of the clinician. Furthermore, purely functional visual loss is never a diagnosis of exclusion, and must be supported by positive findings on examination that demonstrate normal visual function. The relationship of true psychological disease and functional visual loss is unclear and most patients respond well to simple reassurance. PMID:20638000

  16. Drugs and hair loss.

    PubMed

    Patel, Mansi; Harrison, Shannon; Sinclair, Rodney

    2013-01-01

    Hair loss is a common complaint, both in men and women, and use of prescription medications is widespread. When there is a temporal association between the onset of hair loss and commencement of a medication, the medication is commonly thought to have caused the hair loss. However, hair loss and in particular telogen effluvium may occur in response to a number of triggers including fever, hemorrhage, severe illness, stress, and childbirth, and a thorough exclusion of these potential confounders is necessary before the hair loss can be blamed on the medication. Certain medications are known to cause hair loss by a variety of mechanisms including anagen arrest, telogen effluvium, or accentuation of androgenetic alopecia by androgens. PMID:23159177

  17. Manipulating Flames with AC Electric Fields

    NASA Astrophysics Data System (ADS)

    Bishop, Kyle

    2013-11-01

    Time-oscillating electric fields applied to plasmas present in flames create steady flows of gas capable of shaping, directing, enhancing, or even extinguishing flames. Interestingly, electric winds induced by AC electric fields can be stronger that those due to static fields of comparable magnitude. Furthermore, unlike static fields, the electric force due to AC fields is localized near the surface of the flame. Consequently, the AC response depends only on the local field at the surface of the flame - not on the position of the electrodes used to generate the field. These results suggest that oscillating electric fields can be used to manipulate and control combustion processes at a distance. To characterize and explain these effects, we investigate a simple experimental system comprising a laminar methane-air flame positioned between two parallel-plate electrodes. We quantify both the electric and hydrodynamic response of the flame as a function of frequency and magnitude of the applied field. A theoretical model shows how steady gas flows emerge from the time-averaged electrical force due to the field-induced motion of ions generated within the flame and by their disappearance by recombination. These results provide useful insights into the application of AC fields to direct combustion processes.

  18. AC electric trapping of neutral atoms

    NASA Astrophysics Data System (ADS)

    Marian, Adela; Schlunk, Sophie; Schoellkopf, Wieland; Meijer, Gerard

    2008-05-01

    We have demonstrated trapping of ultracold ground-state ^87Rb atoms in a macroscopic ac electric trap [1]. Trapping by ac electric fields has been previously achieved for polar molecules [2], as well as Sr atoms on a chip [3], and recently for Rb atoms in a three-phase electric trap [4]. Similar to trapping of ions in a Paul trap, three-dimensional confinement in an ac electric trap is obtained by switching between two saddle-point configurations of the electric field. For the first time, this dynamic confinement is directly visualized with absorption images taken at different phases of the ac switching cycle. Stable electric trapping is observed in a narrow range of switching frequencies around 60 Hz, in agreement with trajectory calculations. In a typical experiment, about 3 x 10^5 Rb atoms are trapped with lifetimes on the order of 9 s and trap depths of about 10 μK. Additionally, we show that the atoms can be used to sensitively probe the electric fields in the trap by imaging the cloud while the fields are still on. References: 1. S. Schlunk et al., PRL 98, 223002 (2007) 2. H. L. Bethlem et al., PRA 74, 063403 (2006) 3. T. Kishimoto et al., PRL 96, 123001 (2006) 4. T. Rieger et al., PRL 99, 063001 (2007)

  19. Ac-dc converter firing error detection

    SciTech Connect

    Gould, O.L.

    1996-07-15

    Each of the twelve Booster Main Magnet Power Supply modules consist of two three-phase, full-wave rectifier bridges in series to provide a 560 VDC maximum output. The harmonic contents of the twelve-pulse ac-dc converter output are multiples of the 60 Hz ac power input, with a predominant 720 Hz signal greater than 14 dB in magnitude above the closest harmonic components at maximum output. The 720 Hz harmonic is typically greater than 20 dB below the 500 VDC output signal under normal operation. Extracting specific harmonics from the rectifier output signal of a 6, 12, or 24 pulse ac-dc converter allows the detection of SCR firing angle errors or complete misfires. A bandpass filter provides the input signal to a frequency-to-voltage converter. Comparing the output of the frequency-to-voltage converter to a reference voltage level provides an indication of the magnitude of the harmonics in the ac-dc converter output signal.

  20. AC power generation from microbial fuel cells

    NASA Astrophysics Data System (ADS)

    Lobo, Fernanda Leite; Wang, Heming; Forrestal, Casey; Ren, Zhiyong Jason

    2015-11-01

    Microbial fuel cells (MFCs) directly convert biodegradable substrates to electricity and carry good potential for energy-positive wastewater treatment. However, the low and direct current (DC) output from MFC is not usable for general electronics except small sensors, yet commercial DC-AC converters or inverters used in solar systems cannot be directly applied to MFCs. This study presents a new DC-AC converter system for MFCs that can generate alternating voltage in any desired frequency. Results show that AC power can be easily achieved in three different frequencies tested (1, 10, 60 Hz), and no energy storage layer such as capacitors was needed. The DC-AC converter efficiency was higher than 95% when powered by either individual MFCs or simple MFC stacks. Total harmonic distortion (THD) was used to investigate the quality of the energy, and it showed that the energy could be directly usable for linear electronic loads. This study shows that through electrical conversion MFCs can be potentially used in household electronics for decentralized off-grid communities.

  1. AC magnetic susceptibility of Bi2223-system

    NASA Astrophysics Data System (ADS)

    Kimishima, Y.; Inagaki, K.; Tanabe, K.; Nagata, N.; Ichiyanagi, Y.

    1998-01-01

    The AC magnetic susceptibilities χ AC of a Bi2223 sintered sample were measured by the Hartshorn bridge method. The linear AC χ' 0 showed the two-steps behavior at T C1 and T C2, where T C1 > T C2. The χ'0-data between T C1 and T C2 has no H AC-dependence and agreed well with those of powder specimen, and they can be regarded as the intragrain magnetic susceptibility. Below the inter-grain transition temperature T C2 the χ″ 0 showed a positive peak. The temperature dependence of χ' 0 and χ″ 0 were analyzed by the Bean's critical-state model. As a result, the temperature dependence of critical current density J C ∝ (1 - T/T C2) β was obtained with β = 2.3-2.6. The non-linear χ' 2 and χ″ 2 below T C2 resemble the behaviors derived from the Bean model, but the negative divergence of χ' 2 may show the evidence of d-wave paring in the present Bi2223-system.

  2. 76 FR 65633 - RIN 1904-AC43

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-24

    ... FR 56678 (September 14, 2011) to make available and invite comments on the framework document for... Part 430 RIN 1904-AC43 Energy Conservation Program: Framework Document for General Service Fluorescent... general service fluorescent lamps and incandescent reflector lamps energy conservation standards in...

  3. ACS Task Force Frames Recommendations on Education.

    ERIC Educational Resources Information Center

    Chemical and Engineering News, 1984

    1984-01-01

    Discusses findings and recommendations of an American Chemical Society (ACS) task force study on the status of chemical education in the United States. Recommendations relate to national concerns; all educational levels; elementary, secondary, university, college, and two-year college chemistry and science; chemistry careers; and industry and…

  4. An ABC Transporter Mutation Is Correlated with Insect Resistance to Bacillus thuringiensis Cry1Ac Toxin

    PubMed Central

    Gahan, Linda J.; Pauchet, Yannick; Vogel, Heiko; Heckel, David G.

    2010-01-01

    Transgenic crops producing insecticidal toxins from Bacillus thuringiensis (Bt) are commercially successful in reducing pest damage, yet knowledge of resistance mechanisms that threaten their sustainability is incomplete. Insect resistance to the pore-forming Cry1Ac toxin is correlated with the loss of high-affinity, irreversible binding to the mid-gut membrane, but the genetic factors responsible for this change have been elusive. Mutations in a 12-cadherin-domain protein confer some Cry1Ac resistance but do not block this toxin binding in in vitro assays. We sought to identify mutations in other genes that might be responsible for the loss of binding. We employed a map-based cloning approach using a series of backcrosses with 1,060 progeny to identify a resistance gene in the cotton pest Heliothis virescens that segregated independently from the cadherin mutation. We found an inactivating mutation of the ABC transporter ABCC2 that is genetically linked to Cry1Ac resistance and is correlated with loss of Cry1Ac binding to membrane vesicles. ABC proteins are integral membrane proteins with many functions, including export of toxic molecules from the cell, but have not been implicated in the mode of action of Bt toxins before. The reduction in toxin binding due to the inactivating mutation suggests that ABCC2 is involved in membrane integration of the toxin pore. Our findings suggest that ABC proteins may play a key role in the mode of action of Bt toxins and that ABC protein mutations can confer high levels of resistance that could threaten the continued utilization of Bt–expressing crops. However, such mutations may impose a physiological cost on resistant insects, by reducing export of other toxins such as plant secondary compounds from the cell. This weakness could be exploited to manage this mechanism of Bt resistance in the field. PMID:21187898

  5. An ABC transporter mutation is correlated with insect resistance to Bacillus thuringiensis Cry1Ac toxin.

    PubMed

    Gahan, Linda J; Pauchet, Yannick; Vogel, Heiko; Heckel, David G

    2010-12-01

    Transgenic crops producing insecticidal toxins from Bacillus thuringiensis (Bt) are commercially successful in reducing pest damage, yet knowledge of resistance mechanisms that threaten their sustainability is incomplete. Insect resistance to the pore-forming Cry1Ac toxin is correlated with the loss of high-affinity, irreversible binding to the mid-gut membrane, but the genetic factors responsible for this change have been elusive. Mutations in a 12-cadherin-domain protein confer some Cry1Ac resistance but do not block this toxin binding in in vitro assays. We sought to identify mutations in other genes that might be responsible for the loss of binding. We employed a map-based cloning approach using a series of backcrosses with 1,060 progeny to identify a resistance gene in the cotton pest Heliothis virescens that segregated independently from the cadherin mutation. We found an inactivating mutation of the ABC transporter ABCC2 that is genetically linked to Cry1Ac resistance and is correlated with loss of Cry1Ac binding to membrane vesicles. ABC proteins are integral membrane proteins with many functions, including export of toxic molecules from the cell, but have not been implicated in the mode of action of Bt toxins before. The reduction in toxin binding due to the inactivating mutation suggests that ABCC2 is involved in membrane integration of the toxin pore. Our findings suggest that ABC proteins may play a key role in the mode of action of Bt toxins and that ABC protein mutations can confer high levels of resistance that could threaten the continued utilization of Bt-expressing crops. However, such mutations may impose a physiological cost on resistant insects, by reducing export of other toxins such as plant secondary compounds from the cell. This weakness could be exploited to manage this mechanism of Bt resistance in the field. PMID:21187898

  6. Fabrication of polymer waveguide tapers to minimize insertion loss

    NASA Astrophysics Data System (ADS)

    Yacoubian, Araz; Lin, Weiping; Bechtel, James H.

    2001-12-01

    Polymer based electro-optic (EO) modulators and other integrated optic devices have the potential to provide low cost and lightweight alternative for high-speed digital as well as analog RF links. To be truly competitive with existing technologies such as LiNbO3, EO polymer modulators must also meet the criteria of low loss. There are two major causes of loss in EO modulators: waveguide loss (including material loss, scattering, etc.), and fiber- to-waveguide coupling (butting) loss. Various techniques can be utilized to minimize these coupling losses, however, to maintain low cost of component, we resort to the simplest possible approach which is easy to manufacture. Pigtails using standard single mode fiber produce coupling loss on the order of 3 to 5 dB/connection. In order to improve mode size matching yet maintain low drive voltage we incorporate waveguide and fibers tapers. Waveguide tapers resulted to butting losses as low as 1.5 dB/connection, whereas fiber tapers resulted to 2.5 dB/connection butting losses. Combining both techniques together, it was possible to produce 1.3 dB/connection butting loss, however, tapered waveguide devices were less sensitive to alignment tolerance than tapered fiber devices, and therefore less sensitive to environmental conditions.

  7. Galvanic Corrosion In (Graphite/Epoxy)/Alloy Couples

    NASA Technical Reports Server (NTRS)

    Danford, Merlin D.; Higgins, Ralph H.

    1988-01-01

    Effects of galvanic coupling between graphite/epoxy composite material, G/E, and D6AC steel, 6061-T6 aluminum, and Inconel(R) 718 nickel alloy in salt water described in report. Introductory section summarizes previous corrosion studies of G/E with other alloys. Details of sample preparation presented along with photographs of samples before and after immersion.

  8. Spatial coupling of nitrogen inputs and losses in the ocean.

    PubMed

    Deutsch, Curtis; Sarmiento, Jorge L; Sigman, Daniel M; Gruber, Nicolas; Dunne, John P

    2007-01-11

    Nitrogen fixation is crucial for maintaining biological productivity in the oceans, because it replaces the biologically available nitrogen that is lost through denitrification. But, owing to its temporal and spatial variability, the global distribution of marine nitrogen fixation is difficult to determine from direct shipboard measurements. This uncertainty limits our understanding of the factors that influence nitrogen fixation, which may include iron, nitrogen-to-phosphorus ratios, and physical conditions such as temperature. Here we determine nitrogen fixation rates in the world's oceans through their impact on nitrate and phosphate concentrations in surface waters, using an ocean circulation model. Our results indicate that nitrogen fixation rates are highest in the Pacific Ocean, where water column denitrification rates are high but the rate of atmospheric iron deposition is low. We conclude that oceanic nitrogen fixation is closely tied to the generation of nitrogen-deficient waters in denitrification zones, supporting the view that nitrogen fixation stabilizes the oceanic inventory of fixed nitrogen over time. PMID:17215838

  9. High voltage AC/AC electrochemical capacitor operating at low temperature in salt aqueous electrolyte

    NASA Astrophysics Data System (ADS)

    Abbas, Qamar; Béguin, François

    2016-06-01

    We demonstrate that an activated carbon (AC)-based electrochemical capacitor implementing aqueous lithium sulfate electrolyte in 7:3 vol:vol water/methanol mixture can operate down to -40 °C with good electrochemical performance. Three-electrode cell investigations show that the faradaic contributions related with hydrogen chemisorption in the negative AC electrode are thermodynamically unfavored at -40 °C, enabling the system to work as a typical electrical double-layer (EDL) capacitor. After prolonged floating of the AC/AC capacitor at 1.6 V and -40°C, the capacitance, equivalent series resistance and efficiency remain constant, demonstrating the absence of ageing related with side redox reactions at this temperature. Interestingly, when temperature is increased back to 24 °C, the redox behavior due to hydrogen storage reappears and the system behaves as a freshly prepared one.

  10. 48 CFR Appendixes A-C to Chapter 7 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false A Appendixes A-C to Chapter 7 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT Appendixes A-C to Chapter 7...

  11. 48 CFR Appendixes A-C to Chapter 7 - [Reserved

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false A Appendixes A-C to Chapter 7 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT Appendixes A-C to Chapter 7...

  12. Tubular Coupling

    NASA Technical Reports Server (NTRS)

    Rosenbaum, Bernard J. (Inventor)

    2000-01-01

    A system for coupling a vascular overflow graft or cannula to a heart pump. A pump pipe outlet is provided with an external tapered surface which receives the end of a compressible connula. An annular compression ring with a tapered internal bore surface is arranged about the cannula with the tapered internal surface in a facing relationship to the external tapered surface. The angle of inclination of the tapered surfaces is converging such that the spacing between the tapered surfaces decreases from one end of the external tapered surface to the other end thereby providing a clamping action of the tapered surface on a cannula which increases as a function of the length of cannula segment between the tapered surfaces. The annular compression ring is disposed within a tubular locking nut which threadedly couples to the pump and provides a compression force for urging the annular ring onto the cannula between the tapered surfaces. The nut has a threaded connection to the pump body. The threaded coupling to the pump body provides a compression force for the annular ring. The annular ring has an annular enclosure space in which excess cannula material from the compression between the tapered surfaces to "bunch up" in the space and serve as an enlarged annular ring segment to assist holding the cannula in place. The clamped cannula provides a seamless joint connection to the pump pipe outlet where the clamping force is uniformly applied to the cannula because of self alignment of the tapered surfaces. The nut can be easily disconnected to replace the pump if necessary.

  13. Energy losses in switches

    SciTech Connect

    Martin, T.H.; Seamen, J.F.; Jobe, D.O.

    1993-07-01

    The authors experiments show energy losses between 2 and 10 times that of the resistive time predictions. The experiments used hydrogen, helium, air, nitrogen, SF{sub 6} polyethylene, and water for the switching dielectric. Previously underestimated switch losses have caused over predicting the accelerator outputs. Accurate estimation of these losses is now necessary for new high-efficiency pulsed power devices where the switching losses constitute the major portion of the total energy loss. They found that the switch energy losses scale as (V{sub peak}I{sub peak}){sup 1.1846}. When using this scaling, the energy losses in any of the tested dielectrics are almost the same. This relationship is valid for several orders of magnitude and suggested a theoretical basis for these results. Currents up to .65 MA, with voltages to 3 MV were applied to various gaps during these experiments. The authors data and the developed theory indicates that the switch power loss continues for a much longer time than the resistive time, with peak power loss generally occurring at peak current in a ranging discharge instead of the early current time. All of the experiments were circuit code modeled after developing a new switch loss version based on the theory. The circuit code predicts switch energy loss and peak currents as a function of time. During analysis of the data they noticed slight constant offsets between the theory and data that depended on the dielectric. They modified the plasma conductivity for each tested dielectric to lessen this offset.

  14. AC Conductivity and Dielectric Relaxation Behavior of Sb2S3 Bulk Material

    NASA Astrophysics Data System (ADS)

    Abd El-Rahman, K. F.; Darwish, A. A. A.; Qashou, Saleem I.; Hanafy, T. A.

    2016-04-01

    The Sb2S3 bulk material was used for next-generation anode for lithium-ion batteries. Alternative current (AC) conductivity, dielectric properties and electric modulus of Sb2S3 have been investigated. The measurements were carried out in the frequency range from 40 Hz to 5 MHz and temperature range from 293 K to 453 K. The direct current (DC) conductivity, σ DC, shows an activated behavior and the calculated activation energy is 0.50 eV. The AC conductivity, σ AC, was found to increase with the increase of temperature and frequency. The conduction mechanism of σ AC was controlled by the correlated barrier hopping model. The behavior of the dielectric constant, ɛ', and dielectric loss index, ɛ'', reveal that the polarization process of Sb2S3 is dipolar in nature. The behavior of both ɛ' and ɛ'' reveals that bulk Sb2S3 has no ferroelectric or piezoelectric phase transition. The dielectric modulus, M, gives a simple method for evaluating the activation energy of the dielectric relaxation. The calculated activation energy from M is 0.045 eV.

  15. AC Conductivity and Dielectric Relaxation Behavior of Sb2S3 Bulk Material

    NASA Astrophysics Data System (ADS)

    Abd El-Rahman, K. F.; Darwish, A. A. A.; Qashou, Saleem I.; Hanafy, T. A.

    2016-07-01

    The Sb2S3 bulk material was used for next-generation anode for lithium-ion batteries. Alternative current (AC) conductivity, dielectric properties and electric modulus of Sb2S3 have been investigated. The measurements were carried out in the frequency range from 40 Hz to 5 MHz and temperature range from 293 K to 453 K. The direct current (DC) conductivity, σ DC, shows an activated behavior and the calculated activation energy is 0.50 eV. The AC conductivity, σ AC, was found to increase with the increase of temperature and frequency. The conduction mechanism of σ AC was controlled by the correlated barrier hopping model. The behavior of the dielectric constant, ɛ', and dielectric loss index, ɛ'', reveal that the polarization process of Sb2S3 is dipolar in nature. The behavior of both ɛ' and ɛ'' reveals that bulk Sb2S3 has no ferroelectric or piezoelectric phase transition. The dielectric modulus, M, gives a simple method for evaluating the activation energy of the dielectric relaxation. The calculated activation energy from M is 0.045 eV.

  16. Post-Flash Calibration Darks for the Advanced Camera for Surveys Wide Field Channel (ACS/WFC)

    NASA Astrophysics Data System (ADS)

    Ogaz, S.; Anderson, J.; Golimowski, D.

    2015-06-01

    We present a summary and analysis of the changes made to the ACS/WFC dark reference files. As of January 15, 2015 the ACS team has begun to produce post- flashed dark reference files for the Wide Field Channel (WFC). This change was made to combat the charge transfer efficiency (CTE) losses caused by radiation damage that the two WFC CCDs have suffered since being put into orbit by artificially increasing the background in the dark images. This has resulted in several changes to the reference file pipeline, and an improved calibration dark.

  17. Combined Operation of AC and DC Distribution System with Distributed Generation Units

    NASA Astrophysics Data System (ADS)

    Noroozian, Reza; Abedi, Mehrdad; Gharehpetian, Gevorg

    2010-07-01

    This paper presents a DC distribution system which has been supplied by external AC systems as well as local DG units in order to demonstrate an overall solution to power quality issue. In this paper, the proposed operation method is demonstrated by simulation of power transfer between external AC systems, DG units, AC and DC loads. The power flow control in DC distribution system has been achieved by network converters and DG converters. Also, the mathematical model of the network, DG and load converters are obtained by using the average technique, which allows converter systems accurately simulated and control strategies for this converters is achieved. A suitable control strategy for network converters has been proposed that involves DC voltage droop regulator and novel instantaneous power regulation scheme. Also, a novel control technique has been proposed for DG converters. In this paper, a novel control system based on stationary and synchronously rotating reference frame has been proposed for load converters for supplying AC loads connected to the DC bus by balanced voltages. The several case studies have been studied based on proposed methods. The simulation results show that DC distribution systems including DG units can improve the power quality at the point of common coupling (PCC) in the power distribution system or industrial power system.

  18. Study Under AC Stimulation on Excitement Properties of Weighted Small-World Biological Neural Networks with Side-Restrain Mechanism

    NASA Astrophysics Data System (ADS)

    Yuan, Wu-Jie; Luo, Xiao-Shu; Jiang, Pin-Qun

    2007-02-01

    In this paper, we propose a new model of weighted small-world biological neural networks based on biophysical Hodgkin-Huxley neurons with side-restrain mechanism. Then we study excitement properties of the model under alternating current (AC) stimulation. The study shows that the excitement properties in the networks are preferably consistent with the behavior properties of a brain nervous system under different AC stimuli, such as refractory period and the brain neural excitement response induced by different intensities of noise and coupling. The results of the study have reference worthiness for the brain nerve electrophysiology and epistemological science.

  19. Hearing Loss and Cytomegalovirus.

    ERIC Educational Resources Information Center

    Strauss, Melvin

    1997-01-01

    Cytomegalovirus is the most common cause of congenital virally induced hearing loss. Maternal infection is most often asymptomatic as is the infection in the newborn. Hearing loss occurs in both clinically apparent infection and in the asymptomatic infection. Current methods of detection, treatment, and prevention and research efforts are…

  20. Hereditary Hearing Loss.

    ERIC Educational Resources Information Center

    Tran, LenhAnh P.; Grundfast, Kenneth M.

    1997-01-01

    This article discusses inheritance patterns in hearing loss, epidemiology, clues to genetic causes, locating genes that cause hereditary disorders, genes related to hearing loss disorders in individuals with Usher syndrome, Waardenburg syndrome, Treacher-Collins syndrome, Branchio-oto-renal and Pendred syndromes, and the significance of finding…

  1. Anthocyanins and weight loss

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This review evaluated the available scientific literature relative to anthocyanins and weight loss and/or obesity with mention of other effects of anthocyanins on pathologies that are closely related to obesity. Although there is considerable popular press concerning anthocyanins and weight loss, th...

  2. CEBAF beam loss accounting

    SciTech Connect

    Ursic, R.; Mahoney, K.; Hovater, C.; Hutton, A.; Sinclair, C.

    1995-12-31

    This paper describes the design and implementation of a beam loss accounting system for the CEBAF electron accelerator. This system samples the beam curent throughout the beam path and measures the beam current accurately. Personnel Safety and Machine Protection systems use this system to turn off the beam when hazardous beam losses occur.

  3. Understanding Rural Population Loss.

    ERIC Educational Resources Information Center

    McGranahan, David A.; Beale, Calvin L.

    2002-01-01

    A quarter of nonmetro counties lost population in the 1990s, but population loss was not related to poverty rate or low educational levels, perhaps because low-skill workers can no longer expect better wages in urban areas. Population loss was related to low population density and remoteness (which decrease access to services), lack of natural…

  4. Help! It's Hair Loss!

    MedlinePlus

    ... Homework? Here's Help White House Lunch Recipes Help! It's Hair Loss! KidsHealth > For Kids > Help! It's Hair Loss! Print A A A Text Size ... part above the skin, is dead. (That's why it doesn't hurt to get a haircut!) This ...

  5. Understanding Grief & Loss.

    ERIC Educational Resources Information Center

    Parker, Judith

    1995-01-01

    Although death is the one certainty in life, death or the grieving process is rarely discussed. Grief includes physical, emotional, spiritual, and psychological reactions to loss, and is not limited to feelings about death. Grief can be the response to loss of home or country, separation or displacement, and changes resulting from new life stages.…

  6. Weight Loss Surgery

    MedlinePlus

    Weight loss surgery helps people with extreme obesity to lose weight. It may be an option if you cannot lose weight through diet and exercise or have serious health problems caused by obesity. There are different types of weight loss surgery. They often limit the ...

  7. Convective and diffusive energetic particle losses induced by shear Alfvén waves in the ASDEX upgrade tokamak.

    PubMed

    García-Muñoz, M; Hicks, N; van Voornveld, R; Classen, I G J; Bilato, R; Bobkov, V; Bruedgam, M; Fahrbach, H-U; Igochine, V; Jaemsae, S; Maraschek, M; Sassenberg, K

    2010-05-01

    We present here the first phase-space characterization of convective and diffusive energetic particle losses induced by shear Alfvén waves in a magnetically confined fusion plasma. While single toroidal Alfvén eigenmodes (TAE) and Alfvén cascades (AC) eject resonant fast ions in a convective process, an overlapping of AC and TAE spatial structures leads to a large fast-ion diffusion and loss. Diffusive fast-ion losses have been observed with a single TAE above a certain threshold in the fluctuation amplitude. PMID:20482185

  8. Miscarriage experiences of lesbian couples.

    PubMed

    Wojnar, Danuta

    2007-01-01

    This was a descriptive phenomenological study of 10 self-identified lesbian couples who had experienced miscarriage in the context of a committed relationship. Analysis of individual and joint open-ended interviews revealed that the experience of miscarriage for lesbian couples must be viewed from the perspective of the difficulties surrounding conception as well as the actual pregnancy loss. The overarching theme, "We are not in control," captures the struggles lesbian couples faced in conceiving their pregnancies and the sense of loss that accompanied miscarrying. These experiences constituted two sub-themes: "We work so hard to get a baby" and "It hurts so bad: The sorrow of miscarriage." Our results indicate that the experience of miscarriage is compounded by the complexities of planning and achieving pregnancy. Practitioners need to be aware of the unique perspectives lesbian couples have on pregnancy and miscarriage and remain sensitive to their unique needs. Findings may serve as an intervention framework for nurse midwives and others caring for lesbian couples after miscarriage. PMID:17826711

  9. [Inner Ear Hearing Loss].

    PubMed

    Hesse, G

    2016-06-01

    Hearing loss is one of the most dominant handicaps in modern societies, which additionally very often is not realized or not admitted. About one quarter of the general population suffers from inner ear hearing loss and is therefore restricted in communicational skills. Demographic factors like increasing age play an important role as well as environmental influences and an increasing sound and noise exposure especially in leisure activities. Thus borders between a "classical" presbyacusis - if it ever existed - and envirionmentally induced hearing loss disappear. Today restrictions in hearing ability develop earlier in age but at the same time they are detected and diagnosed earlier. This paper can eventually enlighten the wide field of inner ear hearing loss only fragmentarily; therefore mainly new research, findings and developments are reviewed. The first part discusses new aspects of diagnostics of inner ear hearing loss and different etiologies. PMID:27259171

  10. Acute loss of consciousness.

    PubMed

    Tristán, Bekinschtein; Gleichgerrcht, Ezequiel; Manes, Facundo

    2015-01-01

    Acute loss of consciousness poses a fascinating scenario for theoretical and clinical research. This chapter introduces a simple yet powerful framework to investigate altered states of consciousness. We then explore the different disorders of consciousness that result from acute brain injury, and techniques used in the acute phase to predict clinical outcome in different patient populations in light of models of acute loss of consciousness. We further delve into post-traumatic amnesia as a model for predicting cognitive sequels following acute loss of consciousness. We approach the study of acute loss of consciousness from a theoretical and clinical perspective to conclude that clinicians in acute care centers must incorporate new measurements and techniques besides the classic coma scales in order to assess their patients with loss of consciousness. PMID:25702218

  11. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 11 2011-01-01 2011-01-01 false Area Coverage Survey (ACS). 1737.31 Section 1737.31... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  12. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 11 2012-01-01 2012-01-01 false Area Coverage Survey (ACS). 1737.31 Section 1737.31... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  13. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 11 2010-01-01 2010-01-01 false Area Coverage Survey (ACS). 1737.31 Section 1737.31... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  14. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 11 2013-01-01 2013-01-01 false Area Coverage Survey (ACS). 1737.31 Section 1737.31... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  15. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area. (b... 7 Agriculture 11 2014-01-01 2014-01-01 false Area Coverage Survey (ACS). 1737.31 Section...

  16. 21 CFR 886.1630 - AC-powered photostimulator.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false AC-powered photostimulator. 886.1630 Section 886.1630 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Identification. An AC-powered photostimulator is an AC-powered device intended to provide light stimulus...

  17. Methods for Addressing Missing Data with Applications from ACS Exams

    ERIC Educational Resources Information Center

    Brandriet, Alexandra; Holme, Thomas

    2015-01-01

    As part of the ACS Examinations Institute (ACS-EI) national norming process, student performance data sets are collected from professors at colleges and universities from around the United States. Because the data sets are collected on a volunteer basis, the ACS-EI often receives data sets with only students' total scores and without the students'…

  18. 21 CFR 886.1630 - AC-powered photostimulator.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false AC-powered photostimulator. 886.1630 Section 886.1630 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Identification. An AC-powered photostimulator is an AC-powered device intended to provide light stimulus...

  19. Hearing Loss and Older Adults

    MedlinePlus

    ... Home » Health Info » Hearing, Ear Infections, and Deafness Hearing Loss and Older Adults On this page: What is ... about hearing loss and older adults? What is hearing loss? Hearing loss is a sudden or gradual decrease ...

  20. AC conductivity and dielectric measurements of metal-free phthalocyanine thin films dispersed in polycarbonate

    NASA Astrophysics Data System (ADS)

    Riad, A. S.; Korayem, M. T.; Abdel-Malik, T. G.

    1999-10-01

    The dielectric constant and the dielectric loss of thin films of metal-free phthalocyanine dispersed in polycarbonate using ohmic gold electrodes are investigated in the frequency range 20-10 5 Hz and within the temperature range 300-388 K. The frequency dependence of the impedance spectra plotted in the complex plane shows semicircles. The Cole-Cole diagrams have been used to determine the molecular relaxation time, τ, The temperature dependence of τ is expressed by thermally activated process. The AC conductivity σ AC (ω) is found to vary as ωs with the index s⩽1, indicating a dominant hopping process at low temperatures. From the temperature dependence of AC conductivity, free carrier conduction with mean activation energy of 0.33 eV is observed at higher temperatures. Capacitance and loss tangent are found to decrease with increasing frequency and increase with increasing temperature. Such characteristics are found to be in good qualitative agreement with existing equivalent circuit model assuming ohmic contacts.

  1. Effect of nanosilica on optical, electric modulus and AC conductivity of polyvinyl alcohol/polyaniline films

    NASA Astrophysics Data System (ADS)

    El-Sayed, Somyia; Abel-Baset, Tarob; Elfadl, Azza Abou; Hassen, Arafa

    2015-05-01

    Nanosilica (NS) was synthesized by a sol-gel method and mixed with 0.98 polyvinyl alcohol (PVA)/0.02 polyaniline (PANI) in different amounts to produce nanocomposite films. High-resolution transmission electron microscopy (HR-TEM) revealed the average particle size of the NS to be ca. 15 nm. Scanning electron microscopy (SEM) showed that the NS was well-dispersed on the surface of the PVA/PNAI films. The Fourier transform infrared (FTIR) spectra of the samples showed a significant change in the intensity of the characteristic peak of the functional groups in the composite films with the amount of NS added. The absorbance and refractive index (n) of the composites were studied in the UV-vis range, and the optical energy band gap, Eg, and different optical parameters were calculated. The dielectric loss modulus, M″ and ac conductivity, σac, of the samples were studied within 300-425 K and 0.1 kHz-5 MHz, respectively. Two relaxation peaks were observed in the frequency dependence of the dielectric loss modulus, M″. The behavior of σac(f) for the composite films indicated that the conduction mechanism was correlated barrier hopping (CBH). The results of this work are discussed and compared with those of previous studies of similar composites.

  2. Dark coupling

    SciTech Connect

    Gavela, M.B.; Hernández, D.; Honorez, L. Lopez; Mena, O.; Rigolin, S. E-mail: d.hernandez@uam.es E-mail: omena@ific.uv.es

    2009-07-01

    The two dark sectors of the universe—dark matter and dark energy—may interact with each other. Background and linear density perturbation evolution equations are developed for a generic coupling. We then establish the general conditions necessary to obtain models free from non-adiabatic instabilities. As an application, we consider a viable universe in which the interaction strength is proportional to the dark energy density. The scenario does not exhibit ''phantom crossing'' and is free from instabilities, including early ones. A sizeable interaction strength is compatible with combined WMAP, HST, SN, LSS and H(z) data. Neutrino mass and/or cosmic curvature are allowed to be larger than in non-interacting models. Our analysis sheds light as well on unstable scenarios previously proposed.

  3. Thermoacoustic couple

    DOEpatents

    Wheatley, J.C.; Swift, G.W.; Migliori, A.

    1983-10-04

    An apparatus and method for determining acoustic power density level and its direction in a fluid using a single sensor are disclosed. The preferred embodiment of the apparatus, which is termed a thermoacoustic couple, consists of a stack of thin, spaced apart polymeric plates, selected ones of which include multiple bimetallic thermocouple junctions positioned along opposite end edges thereof. The thermocouple junctions are connected in series in the nature of a thermopile, and are arranged so as to be responsive to small temperature differences between the opposite edges of the plates. The magnitude of the temperature difference, as represented by the magnitude of the electrical potential difference generated by the thermopile, is found to be directly related to the level of acoustic power density in the gas.

  4. Loss of 115 kV Power

    SciTech Connect

    Smith, J.A.

    2001-08-22

    This report discusses the postulated loss of 115 kV power. Continuous electrical power to Savannah River Plant reactors is necessary to maintain water flow for heat removal and essential monitoring and control. Should power supplied to the plant 115 kV system from offsite be lost, on-site generation is sufficient to maintain all reactors in a safe shutdown mode for an indefinite period. Should on-site generators for the 115 kV grid also be lost, diesel-electric generators within each reactor building are also sufficient to maintain safe shutdown for a finite period. In all cases DC power for necessary monitoring and control would be available from battery systems with AC converter backup.

  5. Initial Implementation Strategy for Drizzle with ACS

    NASA Astrophysics Data System (ADS)

    Sparks, W. B.; Hack, W.; Hook, R. N.

    2001-04-01

    In order to provide geometric correction for single pointing ACS images, and to provide geometric correction together with simple image combination for associations of ACS images, we describe plans to implement the "drizzle" code by means of a python wrapper, and to use this wrapper in calacs. The initial strategy will endeavour to be robust and scientifically accurate, although not necessarily optimal. An upgrade path is outlined which could lead to significantly improved processing, involving an iterative pass through the data. The tools will be available stand-alone, offering a greater degree of flexibility than in pipeline implementation. The output product will be a multiple extension fits file containing the data (units counts per second), a weight image and a context image. The latter are provided by the drizzle program and are related to the variance and data quality arrays respectively.

  6. THE ACS NEARBY GALAXY SURVEY TREASURY

    SciTech Connect

    Dalcanton, Julianne J.; Williams, Benjamin F.; Rosema, Keith; Gogarten, Stephanie M.; Christensen, Charlotte; Gilbert, Karoline; Hodge, Paul; Seth, Anil C.; Dolphin, Andrew; Holtzman, Jon; Skillman, Evan D.; Weisz, Daniel; Cole, Andrew; Girardi, Leo; Karachentsev, Igor D.; Olsen, Knut; Freeman, Ken; Gallart, Carme; De Jong, Roelof S. E-mail: ben@astro.washington.edu E-mail: stephanie@astro.washington.edu E-mail: fabio@astro.washington.edu E-mail: aseth@cfa.harvard.edu

    2009-07-15

    The ACS Nearby Galaxy Survey Treasury (ANGST) is a systematic survey to establish a legacy of uniform multi-color photometry of resolved stars for a volume-limited sample of nearby galaxies (D < 4 Mpc). The survey volume encompasses 69 galaxies in diverse environments, including close pairs, small and large groups, filaments, and truly isolated regions. The galaxies include a nearly complete range of morphological types spanning a factor of {approx}10{sup 4} in luminosity and star formation rate. The survey data consist of images taken with the Advanced Camera for Surveys (ACS) on the Hubble Space Telescope (HST), supplemented with archival data and new Wide Field Planetary Camera 2 (WFPC2) imaging taken after the failure of ACS. Survey images include wide field tilings covering the full radial extent of each galaxy, and single deep pointings in uncrowded regions of the most massive galaxies in the volume. The new wide field imaging in ANGST reaches median 50% completenesses of m {sub F475W} = 28.0 mag, m {sub F606W} = 27.3 mag, and m {sub F814W} = 27.3 mag, several magnitudes below the tip of the red giant branch (TRGB). The deep fields reach magnitudes sufficient to fully resolve the structure in the red clump. The resulting photometric catalogs are publicly accessible and contain over 34 million photometric measurements of >14 million stars. In this paper we present the details of the sample selection, imaging, data reduction, and the resulting photometric catalogs, along with an analysis of the photometric uncertainties (systematic and random), for both ACS and WFPC2 imaging. We also present uniformly derived relative distances measured from the apparent magnitude of the TRGB.

  7. Large aperture ac interferometer for optical testing.

    PubMed

    Moore, D T; Murray, R; Neves, F B

    1978-12-15

    A 20-cm clear aperture modified Twyman-Green interferometer is described. The system measures phase with an AC technique called phase-lock interferometry while scanning the aperture with a dual galvanometer scanning system. Position information and phase are stored in a minicomputer with disk storage. This information is manipulated with associated software, and the wavefront deformation due to a test component is graphically displayed in perspective and contour on a CRT terminal. PMID:20208642

  8. Highlights of the Dallas ACS Meeting

    NASA Astrophysics Data System (ADS)

    Wildeman, Thomas R.; Freilich, Mark; Kelter, Paul B.

    1998-06-01

    Without a doubt, a primary feature of the 1998 Spring National Meeting in Dallas was the High School Program, which was organized by George Hague, and the impact that the Texas teachers had on other participants. Over 150 teachers registered for the meeting and participated in the program. Their organizational skills were used to reinstitute the High School/College Interface Luncheon. (The High School/College Interface Luncheon will also be held at the Fall ACS Meeting in Boston.)

  9. Graphs for Isotopes of 89-Ac (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides a graphic representation of nucleon separation energies and residual interaction parameters for isotopes of the chemical element 89-Ac (Actinium, atomic number Z = 89).

  10. Loss induced amplification of graphene plasmons.

    PubMed

    Lin, Xiao; Li, Rujiang; Gao, Fei; Li, Erping; Zhang, Xianmin; Zhang, Baile; Chen, Hongsheng

    2016-02-15

    This Letter introduces a new mechanism to reverse and control the effect of losses in the plasmonic systems by using a coupled parity-time symmetric graphene waveguide with complex potentials. In order to explore the uncharted properties of parity-time symmetric graphene plasmons, this Letter analytically shows the plasmonic parity-time symmetry breaking in the coupled graphene waveguide by Sommerfeld integration. This phase transition leads to the distinct spatial propagation behaviors of graphene plasmons in the exact or broken parity-time symmetric phase driven by a point source. Particularly, a loss induced plasmonic amplification, as a characteristic of exceptional point behavior, is for the first time, to the best of our knowledge, revealed in the realm of graphene plasmonics. PMID:26872162

  11. Switch contact device for interrupting high current, high voltage, AC and DC circuits

    DOEpatents

    Via, Lester C.; Witherspoon, F. Douglas; Ryan, John M.

    2005-01-04

    A high voltage switch contact structure capable of interrupting high voltage, high current AC and DC circuits. The contact structure confines the arc created when contacts open to the thin area between two insulating surfaces in intimate contact. This forces the arc into the shape of a thin sheet which loses heat energy far more rapidly than an arc column having a circular cross-section. These high heat losses require a dramatic increase in the voltage required to maintain the arc, thus extinguishing it when the required voltage exceeds the available voltage. The arc extinguishing process with this invention is not dependent on the occurrence of a current zero crossing and, consequently, is capable of rapidly interrupting both AC and DC circuits. The contact structure achieves its high performance without the use of sulfur hexafluoride.

  12. Iron losses in sweat

    SciTech Connect

    Brune, M.; Magnusson, B.; Persson, H.; Hallberg, L.

    1986-03-01

    The losses of iron in whole body cell-free sweat were determined in eleven healthy men. A new experimental design was used with a very careful cleaning procedure of the skin and repeated consecutive sampling periods of sweat in a sauna. The purpose was to achieve a steady state of sweat iron losses with minimal influence from iron originating from desquamated cells and iron contaminating the skin. A steady state was reached in the third sauna period (second sweat sampling period). Iron loss was directly related to the volume of sweat lost and amounted to 22.5 micrograms iron/l sweat. The findings indicate that iron is a physiological constituent of sweat and derived not only from contamination. Present results imply that variations in the amount of sweat lost will have only a marginal effect on the variation in total body iron losses.

  13. Medications for Memory Loss

    MedlinePlus

    ... memory loss, confusion, and problems with thinking and reasoning) of Alzheimer's disease. As Alzheimer’s progresses, brain cells ... the latest Alzheimer's medications available today, and the clinical trials that may bring us closer to new ...

  14. Blindness and vision loss

    MedlinePlus

    ... eye ( chemical burns or sports injuries) Diabetes Glaucoma Macular degeneration The type of partial vision loss may differ, ... tunnel vision and missing areas of vision With macular degeneration, the side vision is normal but the central ...

  15. Living with vision loss

    MedlinePlus

    ... EH, Katz PR, Malone ML, eds. Practice of Geriatrics . 4th ed. Philadelphia, PA: Elsevier Saunders; 2007:chap ... Shega JW. Vision loss. In: Wachtel TJ, ed. Geriatric Clinical Advisor: Instant diagnosis and treatment . Philadelphia, PA: ...

  16. Living with Hearing Loss

    MedlinePlus

    ... Current Issue Past Issues Special Section: Focus on Communication Living with Hearing Loss Past Issues / Fall 2008 ... the United States suffer some form of disordered communication. The National Institute on Deafness and Other Communication ...

  17. Prizes for weight loss.

    PubMed Central

    Englberger, L.

    1999-01-01

    A programme of weight loss competitions and associated activities in Tonga, intended to combat obesity and the noncommunicable diseases linked to it, has popular support and the potential to effect significant improvements in health. PMID:10063662

  18. Occupational hearing loss

    MedlinePlus

    Over time, repeated exposure to loud noise and music can cause hearing loss. Sounds above 80 decibels ( ... Airline ground maintenance Construction Farming Jobs involving loud music or machinery In the U.S., laws regulate the ...

  19. Weight Loss Surgery

    MedlinePlus

    ... loss surgery (especially gastric bypass). Doctors call this "dumping syndrome." It can cause nausea, weakness, sweating, cramping, ... high-sugar or high-fat foods can make dumping worse. Patients need to be careful about what ...

  20. Weight loss - unintentional

    MedlinePlus

    ... of laxatives Other causes such as: Eating disorders, anorexia nervosa that have not been diagnosed yet Diabetes that ... do not know the reason. You have other symptoms along with the weight loss.

  1. Muscle function loss

    MedlinePlus

    ... nervous system that cause muscle function loss include: Amyotrophic lateral sclerosis (ALS, or Lou Gehrig's disease) Bell's palsy Botulism ... of recent progress. Curr Opin Rheum Read More Amyotrophic lateral sclerosis Botulism Broken bone Guillain-Barré syndrome Muscle cramps ...

  2. Hearing loss - infants

    MedlinePlus

    ... to sounds through play. These tests, known as visual response audiometry and play audiometry, can better determine ... the cause of hearing loss. Treatment may include: Speech therapy Learning sign language Cochlear implant (for those ...

  3. Sudden Sensorineural Hearing Loss

    PubMed Central

    Kuhn, Maggie; Heman-Ackah, Selena E.; Shaikh, Jamil A.

    2011-01-01

    Sudden sensorineural hearing loss (SSNHL) is commonly encountered in audiologic and otolaryngologic practice. SSNHL is most commonly defined as sensorineural hearing loss of 30dB or greater over at least three contiguous audiometric frequencies occurring within a 72-hr period. Although the differential for SSNHL is vast, for the majority of patients an etiologic factor is not identified. Treatment for SSNHL of known etiology is directed toward that agent, with poor hearing outcomes characteristic for discoverable etiologies that cause inner ear hair cell loss. Steroid therapy is the current mainstay of treatment of idiopathic SSNHL in the United States. The prognosis for hearing recovery for idiopathic SSNHL is dependent on a number of factors including the severity of hearing loss, age, presence of vertigo, and shape of the audiogram. PMID:21606048

  4. Hearing loss and music

    MedlinePlus

    ... iPod or MP3 Player The small ear bud style headphones (inserted into the ears) do not block ... Hearing Loss. National Institute on Deafness and Other Communication Disorders. NIH Pub. No. 14-4233. Updated: March ...

  5. Bone Loss in IBD

    MedlinePlus

    ... DENSITY? Although bone seems as hard as a rock, it’s actually living tissue. Throughout your life, old ... available Bone Loss (.pdf) File: 290 KB 733 Third Avenue, Suite 510, New York, NY 10017 | 800- ...

  6. Understanding Grief and Loss

    MedlinePlus

    ... Other common behaviors include restlessness and excessive activity. Religion and spirituality Grief and loss may also cause ... The grieving person’s age and gender The life history of the person who is grieving, including previous ...

  7. Coping with Memory Loss

    MedlinePlus

    ... either using computerized axial tomography (CAT) scans or magnetic resonance imaging (MRI) – can help to identify strokes and tumors, which can sometimes cause memory loss. “The goal is to rule out factors ...

  8. Electric properties of carbon nano-onion/polyaniline composites: a combined electric modulus and ac conductivity study

    NASA Astrophysics Data System (ADS)

    Papathanassiou, Anthony N.; Mykhailiv, Olena; Echegoyen, Luis; Sakellis, Ilias; Plonska-Brzezinska, Marta E.

    2016-07-01

    The complex electric modulus and the ac conductivity of carbon nano-onion/polyaniline composites were studied from 1 mHz to 1 MHz at isothermal conditions ranging from 15 K to room temperature. The temperature dependence of the electric modulus and the dc conductivity analyses indicate a couple of hopping mechanisms. The distinction between thermally activated processes and the determination of cross-over temperature were achieved by exploring the temperature dependence of the fractional exponent of the dispersive ac conductivity and the bifurcation of the scaled ac conductivity isotherms. The results are analyzed by combining the granular metal model (inter-grain charge tunneling of extended electron states located within mesoscopic highly conducting polyaniline grains) and a 3D Mott variable range hopping model (phonon assisted tunneling within the carbon nano-onions and clusters).

  9. [A novel Fe/AC desulphurizer at low temperature].

    PubMed

    Ma, J; Liu, S; Liu, Z; Zhu, Z; An, M; Yan, B

    2001-11-01

    Activated coke was used to support Fe2O3(Fe/AC) for flue gas SO2 removal. Reaction conditions on DeSOx activity were investigated. The results show that Fe/AC had higher activity than AC or Fe2O3 at temperature of 120 degrees C-250 degrees C. H2SO4 and Fe2(SO4)3 were formed after Fe/AC sorbed SO2, H2O and O2 increased the amount of SO2 adsorption. Fe/AC derived from AC of higher BET surface area had higher DeSOx activity. Fe/AC was suitable to be used at GHSV below 800 L/(kg.h). PMID:11855176

  10. Electronic structure of Sc 2AC (A=Al, Ga, In, Tl)

    NASA Astrophysics Data System (ADS)

    Music, Denis; Sun, Zhimei; Schneider, Jochen M.

    2005-02-01

    Using ab initio calculations, we have studied Sc 2AC with A=Al, Ga, In and Tl. We show that C 2p and Sc 3d as well as A p and Sc 3d states are hybridized, but the antibonding states in the vicinity of the Fermi level weaken the overall bonding. In terms of the chemical bonding, the influence of the size of the A element is minute. Furthermore, the bulk modulus of the corresponding binary transition metal carbide is not conserved in these phases. Therefore, Sc 2AC can be classified as weakly coupled MAX phases according to Sun and co-workers [Z. Sun, D. Music, R. Ahuja, S. Li, J.M. Schneider, Phys. Rev. B 70 (2004) 092102]. It is our ambition that these calculations will stimulate experimental research on these compounds.

  11. Multiphoton ac Stark effect in a bichromatically driven two-level atom

    NASA Astrophysics Data System (ADS)

    Rudolph, T. G.; Freedhoff, H. S.; Ficek, Z.

    1998-08-01

    We study the interaction of a two-level atom with two lasers of different frequencies and amplitudes: a strong laser of Rabi frequency 2Ω1 on resonance with the atomic transition, and a weaker laser detuned by subharmonics (2Ω1/n) of the Rabi frequency of the first. We find that under these conditions the second laser couples the dressed states created by the first in an n-photon process, resulting in ``doubly dressed'' states and in a ``multiphoton ac Stark'' effect. We calculate the eigenstates of the doubly dressed atom and their energies, and illustrate the role of this multiphoton ac Stark effect in its fluorescence, absorption, and Autler-Townes spectra.

  12. High-fidelity ac gate operations of a three-electron double quantum dot qubit

    NASA Astrophysics Data System (ADS)

    Wong, Clement H.

    2016-01-01

    Semiconductor quantum dots in silicon are promising qubits because of long spin coherence times and their potential for scalability. However, such qubits with complete electrical control and fidelities above the threshold for quantum error correction have not yet been achieved. We show theoretically that the threshold fidelity can be achieved with ac gate operation of the quantum dot hybrid qubit. Formed by three electrons in a double dot, this qubit is electrically controlled, does not require magnetic fields, and runs at gigahertz (GHz) gate speeds. We analyze the decoherence caused by 1 /f charge noise in this qubit, find parameters that minimize the charge noise dependence in the qubit frequency, and determine the optimal working points for ac gate operations that drive the detuning and tunnel coupling.

  13. Direct Measurement of Ab and Ac at the Z0 Pole Using a Lepton Tag

    NASA Astrophysics Data System (ADS)

    Abe, Kenji; Abe, Koya; Abe, T.; Adam, I.; Akagi, T.; Allen, N. J.; Arodzero, A.; Ash, W. W.; Aston, D.; Baird, K. G.; Baltay, C.; Band, H. R.; Barakat, M. B.; Bardon, O.; Barklow, T. L.; Bashindzhagyan, G. L.; Bauer, J. M.; Bellodi, G.; Ben-David, R.; Benvenuti, A. C.; Bilei, G. M.; Bisello, D.; Blaylock, G.; Bogart, J. R.; Bolen, B.; Bower, G. R.; Brau, J. E.; Breidenbach, M.; Bugg, W. M.; Burke, D.; Burnett, T. H.; Burrows, P. N.; Byrne, R. M.; Calcaterra, A.; Calloway, D.; Camanzi, B.; Carpinelli, M.; Cassell, R.; Castaldi, R.; Castro, A.; Cavalli-Sforza, M.; Chou, A.; Church, E.; Cohn, H. O.; Coller, J. A.; Convery, M. R.; Cook, V.; Cotton, R.; Cowan, R. F.; Coyne, D. G.; Crawford, G.; Damerell, C. J.; Danielson, M. N.; Daoudi, M.; de Groot, N.; dell'Orso, R.; Dervan, P. J.; de Sangro, R.; Dima, M.; D'Oliveira, A.; Dong, D. N.; Doser, M.; Dubois, R.; Eisenstein, B. I.; Eschenburg, V.; Etzion, E.; Fahey, S.; Falciai, D.; Fan, C.; Fernandez, J. P.; Fero, M. J.; Flood, K.; Frey, R.; Gillman, T.; Gladding, G.; Gonzalez, S.; Goodman, E. R.; Hart, E. L.; Harton, J. L.; Hasan, A.; Hasuko, K.; Hedges, S. J.; Hertzbach, S. S.; Hildreth, M. D.; Huber, J.; Huffer, M. E.; Hughes, E. W.; Huynh, X.; Hwang, H.; Iwasaki, M.; Jackson, D. J.; Jacques, P.; Jaros, J. A.; Jiang, Z. Y.; Johnson, A. S.; Johnson, J. R.; Johnson, R. A.; Junk, T.; Kajikawa, R.; Kalelkar, M.; Kamyshkov, Y.; Kang, H. J.; Karliner, I.; Kawahara, H.; Kim, Y. D.; King, R.; King, M. E.; Kofler, R. R.; Krishna, N. M.; Kroeger, R. S.; Langston, M.; Lath, A.; Leith, D. W.; Lia, V.; Lin, C.-J. S.; Liu, X.; Liu, M. X.; Loreti, M.; Lu, A.; Lynch, H. L.; Ma, J.; Mahjouri, M.; Mancinelli, G.; Manly, S.; Mantovani, G.; Markiewicz, T. W.; Maruyama, T.; Masuda, H.; Mazzucato, E.; McKemey, A. K.; Meadows, B. T.; Menegatti, G.; Messner, R.; Mockett, P. M.; Moffeit, K. C.; Moore, T. B.; Morii, M.; Muller, D.; Murzin, V.; Nagamine, T.; Narita, S.; Nauenberg, U.; Neal, H.; Nussbaum, M.; Oishi, N.; Onoprienko, D.; Osborne, L. S.; Panvini, R. S.; Park, H.; Park, C. H.; Pavel, T. J.; Peruzzi, I.; Piccolo, M.; Piemontese, L.; Pieroni, E.; Pitts, K. T.; Plano, R. J.; Prepost, R.; Prescott, C. Y.; Punkar, G. D.; Quigley, J.; Ratcliff, B. N.; Reeves, T. W.; Reidy, J.; Reinertsen, P. L.; Rensing, P. E.; Rochester, L. S.; Rowson, P. C.; Russell, J. J.; Saxton, O. H.; Schalk, T.; Schindler, R. H.; Schumm, B. A.; Schwiening, J.; Sen, S.; Serbo, V. V.; Shaevitz, M. H.; Shank, J. T.; Shapiro, G.; Sherden, D. J.; Shmakov, K. D.; Simopoulos, C.; Sinev, N. B.; Smith, S. R.; Smy, M. B.; Snyder, J. A.; Staengle, H.; Stahl, A.; Stamer, P.; Steiner, R.; Steiner, H.; Strauss, M. G.; Su, D.; Suekane, F.; Sugiyama, A.; Suzuki, S.; Swartz, M.; Szumilo, A.; Takahashi, T.; Taylor, F. E.; Thom, J.; Torrence, E.; Toumbas, N. K.; Usher, T.; Vannini, C.; Va'Vra, J.; Vella, E.; Venuti, J. P.; Verdier, R.; Verdini, P. G.; Wagner, S. R.; Wagner, D. L.; Waite, A. P.; Walston, S.; Wang, J.; Ward, C.; Watts, S. J.; Weidemann, A. W.; Weiss, E. R.; Whitaker, J. S.; White, S. L.; Wickens, F. J.; Williams, B.; Williams, D. C.; Williams, S. H.; Willocq, S.; Wilson, R. J.; Wisniewski, W. J.; Wittlin, J. L.; Woods, M.; Word, G. B.; Wright, T. R.; Wyss, J.; Yamamoto, R. K.; Yamartino, J. M.; Yang, X.; Yashima, J.; Yellin, S. J.; Young, C. C.; Yuta, H.; Zapalac, G.; Zdarko, R. W.; Zhou, J.

    1999-10-01

    The parity violation parameters Ab and Ac of the Zbb¯ and Zcc¯ couplings have been measured directly, using the polar angle dependence of the Z0-pole polarized cross sections. Bottom and charmed hadrons were tagged via semileptonic decays. Both the muon and electron identification algorithms take advantage of new multivariate techniques, incorporating for the first time information from the SLD Cˇerenkov Ring Imaging Detector. Based on the 1993-1995 SLD sample of 150 000 Z0 decays produced with highly polarized electron beams, we measure Ab = 0.910+/-0.068\\(stat\\)+/-0.037\\(syst\\), Ac = 0.642+/-0.110\\(stat\\)+/-0.063\\(syst\\).

  14. Heat Loss Imagery

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Infrared scanning devices are being used to produce images that show, by color or black-and-white shading differences, which buildings and homes are losing heat to the outdoors, and how much. Heat loss surveys done by Texas Instruments, Daedalus Enterprises, Inc. and other companies have growing acceptance of their services among industrial firms, utilities, local governments, and state and federal agencies interested in promoting heat loss awareness and inspiring corrective actions.

  15. Structure-guided creation of AcAP5-derived and platelet targeted factor Xa inhibitors.

    PubMed

    Zhu, Yuanjun; Lin, Yuan; Liu, Aihua; Shui, Mengyang; Li, Ruyi; Liu, Xiaoyan; Hu, Wenhui; Wang, Yinye

    2015-06-15

    Anticoagulants and anti-platelet agents are simultaneously administrated in clinical practice (i.e. percutaneous coronary intervention), which cause significant risk of systemic bleeding. Targeted delivery of anticoagulants to the activated platelets at sites of vascular injuries may condense the site-specific anticoagulant effect and reduce the hemorrhage side effects in uninjured vessels. To this end, we prepared three ancylostoma caninum anticoagulant peptide 5 (AcAP5) variants NR1, NR2 and NR3 engineered with a platelet-binding Arg-Gly-Asp (RGD) motif and evaluated their anti-Factor Xa (FXa) and platelet-binding effects. These RGD-containing AcAP5 variants were capable of interacting with platelet receptor αIIbβ3 as shown in computational analysis. All variants, especially NR2 and NR3, retained entirely the anti-FXa function of parent AcAP5. Moreover, they prevented the formation of occlusive thrombi in rat carotid artery injury model, suggesting that they inhibit platelet aggregation in vivo. Further functional investigation of NR3 demonstrated that NR3 inhibited platelet aggregation in vitro and FXa activity in vivo, and prolonged the coagulation time, all in a dose-dependent manner. Through flow cytometry assay, we confirmed the binding of NR3 to αIIbβ3 receptor. In mouse model of carotid artery endothelium injury, NR3-treated mice showed less tail bleeding time than AcAP5-treated mice, and aspirin plus NR3 treatment exhibited moderate reduction of blood loss compared with aspirin plus AcAP5 treatment. These results indicate the feasibility to engineer a novel FXa inhibitor specifically targeting the activated platelets, which centralizes its anticoagulation efficacy in the injured vascular endothelium and reduces the risk of systemic bleeding. PMID:25887920

  16. New Mechanism for Quark Energy Loss

    SciTech Connect

    Casalderrey-Solana, Jorge; Fernandez, Daniel; Mateos, David

    2010-04-30

    We show that a heavy quark moving sufficiently fast through a quark-gluon plasma may lose energy by Cherenkov-radiating mesons. We demonstrate that this takes place in all strongly coupled, large-N{sub c} plasmas with a gravity dual. The energy loss is exactly calculable in these models despite being an O(1/N{sub c}) effect. We discuss implications for heavy-ion collision experiments.

  17. Monitoring colloidal stability of polymer-coated magnetic nanoparticles using AC susceptibility measurements.

    PubMed

    Herrera, Adriana P; Barrera, Carola; Zayas, Yashira; Rinaldi, Carlos

    2010-02-15

    The application of the response of magnetic nanoparticles to oscillating magnetic fields to probe transitions in colloidal state and structure of polymer-coated nanoparticles is demonstrated. Cobalt ferrite nanoparticles with narrow size distribution were prepared and shown to respond to oscillating magnetic fields through a Brownian relaxation mechanism, which is dependent on the mechanical coupling between the particle dipoles and the surrounding matrix. These nanoparticles were coated with covalently-attached poly(N-isopropylacrylamide) (pNIPAM) or poly(N-isopropylmethacrylamide) (pNIPMAM) through free radical polymerization. The temperature induced transitions of colloidal suspensions of these nanoparticles were studied through a combination of differential scanning calorimetry (DSC), dynamic light scattering (DLS), and AC susceptibility measurements. In the pNIPAM coated nanoparticles excellent agreement was found for a transition temperature of approximately 30 degrees C by all three methods, although the AC susceptibility measurements indicated aggregation which was not evident from the DLS results. Small-angle neutron scattering (SANS) results obtained for pNIPAM coated nanoparticles confirmed that aggregation indeed occurs above the lower critical transition temperature of pNIPAM. For the pNIPMAM coated nanoparticles DLS and AC susceptibility measurements indicated aggregation at a temperature of approximately 33-35 degrees C, much lower than the transition temperature peak at 40 degrees C observed by DSC. However, the transition observed by DSC is very broad, hence it is possible that aggregation begins to occur at temperatures lower than the peak, as indicated by the AC susceptibility and DLS results. These experiments and observations demonstrate the possibility of using AC susceptibility measurements to probe transitions in colloidal suspensions induced by external stimuli. Because magnetic measurements do not require optical transparency, these

  18. Development of a hardware-based AC microgrid for AC stability assessment

    NASA Astrophysics Data System (ADS)

    Swanson, Robert R.

    As more power electronic-based devices enable the development of high-bandwidth AC microgrids, the topic of microgrid power distribution stability has become of increased interest. Recently, researchers have proposed a relatively straightforward method to assess the stability of AC systems based upon the time-constants of sources, the net bus capacitance, and the rate limits of sources. In this research, a focus has been to develop a hardware test system to evaluate AC system stability. As a first step, a time domain model of a two converter microgrid was established in which a three phase inverter acts as a power source and an active rectifier serves as an adjustable constant power AC load. The constant power load can be utilized to create rapid power flow transients to the generating system. As a second step, the inverter and active rectifier were designed using a Smart Power Module IGBT for switching and an embedded microcontroller as a processor for algorithm implementation. The inverter and active rectifier were designed to operate simultaneously using a synchronization signal to ensure each respective local controller operates in a common reference frame. Finally, the physical system was created and initial testing performed to validate the hardware functionality as a variable amplitude and variable frequency AC system.

  19. Test Status for Proposed Coupling of a Gravitational Force to Extreme Type II YBCO Ceramic Superconductors

    NASA Technical Reports Server (NTRS)

    Noever, David; Li, Ning; Robertson, Tony; Koczor, Ron; Brantley, Whitt

    1999-01-01

    As a Bose condensate, superconductors provide novel conditions for revisiting previously proposed couplings between electromagnetism and gravity. Strong variations in Cooper pair electron density, large conductivity and low magnetic permeability define superconductive and degenerate condensates without the traditional density limits imposed by the Fermi energy (about 10-6 g/cu cm). Recent experiments have reported anomalous weight loss for a test mass suspended above a rotating Type II, YBCO superconductor, with the percentage change (0.05-2.1%) independent of the test mass' chemical composition and diamagnetic properties. A variation of 5 parts per 10(exp 4) was reported above a stationary (non-rotating) superconductor. In the present experiments reported using a sensitive gravimeter (resolution <10(exp -9) unit gravity or variation of 10(exp -6) cm/sq s in accelerations), bulk YBCO superconductors were stably levitated in a DC magnetic field (0.6 Tesla) subject to lateral AC fields (60 Gauss at 60 Hz) and rotation. With magnetic shielding, thermal control and buoyancy compensation, changes in acceleration were measured to be less than 2 parts in 10(exp 8) of the normal gravitational acceleration. This result puts new limits on the strength and range of the proposed coupling between high-Tc superconductors and gravity. Latest test results will be reported, along with status for future improvements and prospects.

  20. The Hubble Legacy Archive ACS grism data

    NASA Astrophysics Data System (ADS)

    Kümmel, M.; Rosati, P.; Fosbury, R.; Haase, J.; Hook, R. N.; Kuntschner, H.; Lombardi, M.; Micol, A.; Nilsson, K. K.; Stoehr, F.; Walsh, J. R.

    2011-06-01

    A public release of slitless spectra, obtained with ACS/WFC and the G800L grism, is presented. Spectra were automatically extracted in a uniform way from 153 archival fields (or "associations") distributed across the two Galactic caps, covering all observations to 2008. The ACS G800L grism provides a wavelength range of 0.55-1.00 μm, with a dispersion of 40 Å/pixel and a resolution of ~80 Å for point-like sources. The ACS G800L images and matched direct images were reduced with an automatic pipeline that handles all steps from archive retrieval, alignment and astrometric calibration, direct image combination, catalogue generation, spectral extraction and collection of metadata. The large number of extracted spectra (73,581) demanded automatic methods for quality control and an automated classification algorithm was trained on the visual inspection of several thousand spectra. The final sample of quality controlled spectra includes 47 919 datasets (65% of the total number of extracted spectra) for 32 149 unique objects, with a median iAB-band magnitude of 23.7, reaching 26.5 AB for the faintest objects. Each released dataset contains science-ready 1D and 2D spectra, as well as multi-band image cutouts of corresponding sources and a useful preview page summarising the direct and slitless data, astrometric and photometric parameters. This release is part of the continuing effort to enhance the content of the Hubble Legacy Archive (HLA) with highly processed data products which significantly facilitate the scientific exploitation of the Hubble data. In order to characterize the slitless spectra, emission-line flux and equivalent width sensitivity of the ACS data were compared with public ground-based spectra in the GOODS-South field. An example list of emission line galaxies with two or more identified lines is also included, covering the redshift range 0.2 - 4.6. Almost all redshift determinations outside of the GOODS fields are new. The scope of science projects

  1. Deletion of the AcMNPV core gene ac109 results in budded virions that are non-infectious

    SciTech Connect

    Fang Minggang; Nie, Yingchao; Theilmann, David A.

    2009-06-20

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac109 is a core gene and its function in the virus life cycle is unknown. To determine its role in the baculovirus life cycle, we used the AcMNPV bacmid system to generate an ac109 deletion virus (vAc{sup 109KO}). Fluorescence and light microscopy showed that transfection of vAc{sup 109KO} results in a single-cell infection phenotype. Viral DNA replication is unaffected and the development of occlusion bodies in vAc{sup 109KO}-transfected cells evidenced progression to the very late phases of viral infection. Western blot and confocal immunofluorescence analysis showed that AC109 is expressed in the cytoplasm and nucleus throughout infection. In addition, AC109 is a structural protein as it was detected in both budded virus (BV) and occlusion derived virus in both the envelope and nucleocapsid fractions. Titration assays by qPCR and TCID{sub 50} showed that vAc{sup 109KO} produced BV but the virions are non-infectious. The vAc{sup 109KO} BV were indistinguishable from the BV of repaired and wild type control viruses as determined by negative staining and electron microscopy.

  2. ZMYND8 Reads the Dual Histone Mark H3K4me1-H3K14ac to Antagonize the Expression of Metastasis-Linked Genes.

    PubMed

    Li, Na; Li, Yuanyuan; Lv, Jie; Zheng, Xiangdong; Wen, Hong; Shen, Hongjie; Zhu, Guangjing; Chen, Tsai-Yu; Dhar, Shilpa S; Kan, Pu-Yeh; Wang, Zhibin; Shiekhattar, Ramin; Shi, Xiaobing; Lan, Fei; Chen, Kaifu; Li, Wei; Li, Haitao; Lee, Min Gyu

    2016-08-01

    Histone acetylation, including acetylated H3K14 (H3K14ac), is generally linked to gene activation. Monomethylated histone H3 lysine 4 (H3K4me1), together with other gene-activating marks, denotes active genes. In contrast to usual gene-activating functions of H3K14ac and H3K4me1, we here show that the dual histone modification mark H3K4me1-H3K14ac is recognized by ZMYND8 (also called RACK7) and can function to counteract gene expression. We identified ZMYND8 as a transcriptional corepressor of the H3K4 demethylase JARID1D. ZMYND8 antagonized the expression of metastasis-linked genes, and its knockdown increased the cellular invasiveness in vitro and in vivo. The plant homeodomain (PHD) and Bromodomain cassette in ZMYND8 mediated the combinatorial recognition of H3K4me1-H3K14ac and H3K4me0-H3K14ac by ZMYND8. These findings uncover an unexpected role for the signature H3K4me1-H3K14ac in attenuating gene expression and reveal a metastasis-suppressive epigenetic mechanism in which ZMYND8's PHD-Bromo cassette couples H3K4me1-H3K14ac with downregulation of metastasis-linked genes. PMID:27477906

  3. APN1 is a functional receptor of Cry1Ac but not Cry2Ab in Helicoverpa zea

    PubMed Central

    Wei, Jizhen; Zhang, Min; Liang, Gemei; Wu, Kongming; Guo, Yuyuan; Ni, Xinzhi; Li, Xianchun

    2016-01-01

    Lepidopteran midgut aminopeptidases N (APNs) are phylogenetically divided into eight clusters, designated as APN1–8. Although APN1 has been implicated as one of the receptors for Cry1Ac in several species, its potential role in the mode of action of Cry2Ab has not been functionally determined so far. To test whether APN1 also acts as one of the receptors for Cry1Ac in Helicoverpa zea and even for Cry2Ab in this species, we conducted a gain of function analysis by heterologously expressing H. zea APN1 (HzAPN1) in the midgut and fat body cell lines of H. zea and the ovarian cell line of Spodoptera frugiperda (Sf9) and a loss of function analysis by RNAi (RNA interference) silencing of the endogenous APN1 in the three cell lines using the HzAPN1 double strand RNA (dsRNA). Heterologous expression of HzAPN1 significantly increased the susceptibility of the three cell lines to Cry1Ac, but had no effects on their susceptibility to Cry2Ab. Knocking down of the endogenous APN1 made the three cell lines resistant to Cry1Ac, but didn’t change cell lines susceptibility to Cry2Ab. The findings from this study demonstrate that HzAPN1 is a functional receptor of Cry1Ac, but not Cry2Ab. PMID:26755166

  4. Losses in Ferroelectric Materials

    PubMed Central

    Liu, Gang; Zhang, Shujun; Jiang, Wenhua; Cao, Wenwu

    2015-01-01

    Ferroelectric materials are the best dielectric and piezoelectric materials known today. Since the discovery of barium titanate in the 1940s, lead zirconate titanate ceramics in the 1950s and relaxor-PT single crystals (such as lead magnesium niobate-lead titanate and lead zinc niobate-lead titanate) in the 1980s and 1990s, perovskite ferroelectric materials have been the dominating piezoelectric materials for electromechanical devices, and are widely used in sensors, actuators and ultrasonic transducers. Energy losses (or energy dissipation) in ferroelectrics are one of the most critical issues for high power devices, such as therapeutic ultrasonic transducers, large displacement actuators, SONAR projectors, and high frequency medical imaging transducers. The losses of ferroelectric materials have three distinct types, i.e., elastic, piezoelectric and dielectric losses. People have been investigating the mechanisms of these losses and are trying hard to control and minimize them so as to reduce performance degradation in electromechanical devices. There are impressive progresses made in the past several decades on this topic, but some confusions still exist. Therefore, a systematic review to define related concepts and clear up confusions is urgently in need. With this objective in mind, we provide here a comprehensive review on the energy losses in ferroelectrics, including related mechanisms, characterization techniques and collections of published data on many ferroelectric materials to provide a useful resource for interested scientists and engineers to design electromechanical devices and to gain a global perspective on the complex physical phenomena involved. More importantly, based on the analysis of available information, we proposed a general theoretical model to describe the inherent relationships among elastic, dielectric, piezoelectric and mechanical losses. For multi-domain ferroelectric single crystals and ceramics, intrinsic and extrinsic energy

  5. dc and ac magnetic properties of thin-walled Nb cylinders with and without a row of antidots.

    PubMed

    Tsindlekht, M I; Genkin, V M; Felner, I; Zeides, F; Katz, N; Gazi, Š; Chromik, Š; Dobrovolskiy, O V; Sachser, R; Huth, M

    2016-06-01

    dc and ac magnetic properties of two thin-walled superconducting Nb cylinders with a rectangular cross-section are reported. Magnetization curves and the ac response were studied on as-prepared and patterned samples in magnetic fields parallel to the cylinder axis. A row of micron-sized antidots (holes) was made in the film along the cylinder axis. Avalanche-like jumps of the magnetization are observed for both samples at low temperatures for magnetic fields not only above H c1, but in fields lower than H c1 in the vortex-free region. The positions of the jumps are not reproducible and they change from one experiment to another, resembling vortex lattice instabilities usually observed for magnetic fields larger than H c1. At temperatures above [Formula: see text] and [Formula: see text] the magnetization curves become smooth for the patterned and the as-prepared samples, respectively. The magnetization curve of a reference planar Nb film in the parallel field geometry does not exhibit jumps in the entire range of accessible temperatures. The ac response was measured in constant and swept dc magnetic field modes. Experiment shows that ac losses at low magnetic fields in a swept field mode are smaller for the patterned sample. For both samples the shapes of the field dependences of losses and the amplitude of the third harmonic are the same in constant and swept field near H c3. This similarity does not exist at low fields in a swept mode. PMID:27143621

  6. Fluid-loss control

    SciTech Connect

    Crowe, C.W.; Trittipo, B.L. ); Hutchinson, B.H. )

    1989-08-01

    Acid fluid loss is extremely difficult to control and is generally considered to be the major factor limiting the effectiveness of acid fracturing treatments. Chemical erosion of fracture faces and the development of wormholes are largely responsible for the reduced efficiency of acid fracturing fluids. The creation of acid wormholes increases the effective area from which leakoff occurs, thus reducing the acid hydraulic efficiency. Once wormholes form, most acid fluid loss originates from these wormholes rather than penetrating uniformly into the fracture face. Methods of acid fluid-loss control are discussed and evaluated with an improved fluid-loss test procedure. This procedure uses limestone cores of sufficient length to contain wormhole growth. Studies demonstrate that if wormhole growth can be controlled, acid fluid loss approaches that of nonreactive fluids. An improved acid fracturing fluid having unique rheological characteristics is described. This acid has a low initial viscosity but temporarily becomes extremely viscous during leakoff. This high leakoff viscosity blocks wormhole development and prevents acid entry into natural fractures. After the treatment, spent-acid viscosity declines rapidly to ensure easier cleanup.

  7. Economic losses due to catastrophes

    NASA Astrophysics Data System (ADS)

    Wendel, JoAnna

    2014-04-01

    Worldwide economic loss due to catastrophic events added up to US140 billion in 2013, with insured losses adding up to 45 billion, according to a report by the insurance provider Swiss Re. Though these numbers are down from 196 billion in economic losses and 81 billion in insurance losses in 2012, Swiss Re reports an upward trend in losses.

  8. Sleep Loss and Inflammation

    PubMed Central

    Simpson, Norah S.; Meier-Ewert, Hans K.; Haack, Monika

    2012-01-01

    Controlled, experimental studies on the effects of acute sleep loss in humans have shown that mediators of inflammation are altered by sleep loss. Elevations in these mediators have been found to occur in healthy, rigorously screened individuals undergoing experimental vigils of more than 24 hours, and have also been seen in response to various durations of sleep restricted to between 25 and 50% of a normal 8 hour sleep amount. While these altered profiles represent small changes, such sub-clinical shifts in basal inflammatory cytokines are known to be associated with the future development of metabolic syndrome disease in healthy, asymptomatic individuals. Although the mechanism of this altered inflammatory status in humans undergoing experimental sleep loss is unknown, it is likely that autonomic activation and metabolic changes play key roles. PMID:21112025

  9. Perioperative visual loss.

    PubMed

    Kla, Koffi M; Lee, Lorri A

    2016-03-01

    Perioperative visual loss is an infrequent, devastating complication associated with spine surgery, most commonly from ischemic optic neuropathy. Current research and expert opinion indicate that it is associated with procedures that create elevated venous pressure in the head for prolonged periods of time. The largest case-control study on ischemic optic neuropathy associated with spine surgery found six independent and significant risk factors including male sex, obesity, Wilson frame use, longer operative times, greater blood loss, and a lower colloid to crystalloid ratio in the non-blood fluid administration. The American Society of Anesthesiologists developed a practice advisory for the prevention of this complication. In this setting, it is advisable to avoid significant physiologic and hemodynamic perturbations as much as possible, given the uncertainty of the pathophysiology. Because prevention of this complication cannot be guaranteed, consent for perioperative visual loss should be strongly considered in patients at high risk for this complication. PMID:27036604

  10. Congenital sensorineural hearing loss

    SciTech Connect

    Mafee, M.F.; Selis, J.E.; Yannias, D.A.; Valvassori, G.E.; Pruzansky, S.; Applebaum, E.L.; Capek, V.

    1984-02-01

    The ears of 47 selected patients with congenital sensorineural hearing loss were examined with complex-motion tomography. The patients were divided into 3 general categories: those with a recognized syndrome, those with sensorineural hearing loss unrelated to any known syndrome, and those with microtia. A great variety of inner ear anomalies was detected, but rarely were these characteristic of a particular clinical entity. The most common finding was the Mondini malformation or one of its variants. Isolated dysplasia of the internal auditory canal or the vestibular aqueduct may be responsible for sensorineural hearing loss in some patients. Patients with microtia may also have severe inner ear abnormalities despite the fact that the outer and inner ears develop embryologically from completely separate systems.

  11. Female pattern hair loss.

    PubMed

    Ioannides, Dimitrios; Lazaridou, Elizabeth

    2015-01-01

    Female pattern hair loss, or female pattern androgenetic alopecia, is a nonscarring alopecia with a multi-factorial etiology that mostly affects postmenopausal women and is characterized by a reduction in hair density over the crown and frontal scalp. The clinical picture is characterized by a diffuse rarefaction of scalp hair over the mid-frontal scalp and a more-or-less intact frontal hairline without any signs of inflammation or scarring. Although the disease poses only a cosmetic concern, it is chronic and may have a significant negative psychological impact on the affected person. The aim of treating female pattern hair loss is to reduce hair loss and, to a certain extent, succeed in promoting hair regrowth. Various treatment methods are available, but it remains unclear which are the most effective. Early initiation of treatment and the combination of various modalities seem to be more efficacious than monotherapy. PMID:26370643

  12. Polaron effects on the dc- and ac-tunneling characteristics of molecular Josephson junctions

    NASA Astrophysics Data System (ADS)

    Wu, B. H.; Cao, J. C.; Timm, C.

    2012-07-01

    We study the interplay of polaronic effect and superconductivity in transport through molecular Josephson junctions. The tunneling rates of electrons are dominated by vibronic replicas of the superconducting gap, which show up as prominent features in the differential conductance for the dc and ac current. For relatively large molecule-lead coupling, a features that appears when the Josephson frequency matches the vibron frequency can be identified with an over-the-gap structure observed by Marchenkov [Nat. Nanotech. 1748-338710.1038/nnano.2007.2182, 481 (2007)]. However, we are more concerned with the weak-coupling limit, where resonant tunneling through the molecular level dominates. We find that certain features involving both Andreev reflection and vibron emission show an unusual shift of the bias voltage V at their maximum with the gate voltage Vg as V˜(2/3)Vg. Moreover, due to the polaronic effect, the ac Josephson current shows a phase shift of π when the bias eV is increased by one vibronic energy quantum ℏωv. This distinctive even-odd effect is explained in terms of the different sign of the coupling to vibrons of electrons and of Andreev-reflected holes.

  13. Ac resonant charger with charge rate unrelated to preimary power requency

    DOEpatents

    Not Available

    1979-12-07

    An ac resonant charger for a capacitive load, such as a pulse forming network (PFN), is provided with a variable repetition rate unrelated to the frequency of a multi-phase ac power source by using a control unit to select and couple the phase of the power source to the resonant charger in order to charge the capacitive load with a phase that is the next to begin a half cycle. For optimum range in repetition rate and increased charging voltage, the resonant charger includes a step-up transformer and full-wave rectifier. The next phase selected may then be of either polarity, but is always selected to be of a polarity opposite the polarity of the last phase selected so that the transformer core does not saturate. Thyristors are used to select and couple the correct phase just after its zero crossover in response to a sharp pulse generated by a zero-crossover detector. The thyristor that is turned on then automatically turns off after a full half cycle of its associated phase input. A full-wave rectifier couples the secondary winding of the transformer to the load so that the load capacitance is always charged with the same polarity.

  14. AC Resonant charger with charge rate unrelated to primary power frequency

    DOEpatents

    Watson, Harold

    1982-01-01

    An AC resonant charger for a capacitive load, such as a PFN, is provided with a variable repetition rate unrelated to the frequency of a multi-phase AC power source by using a control unit to select and couple the phase of the power source to the resonant charger in order to charge the capacitive load with a phase that is the next to begin a half cycle. For optimum range in repetition rate and increased charging voltage, the resonant charger includes a step-up transformer and full-wave rectifier. The next phase selected may then be of either polarity, but is always selected to be of a polarity opposite the polarity of the last phase selected so that the transformer core does not saturate. Thyristors are used to select and couple the correct phase just after its zero crossover in response to a sharp pulse generated by a zero-crossover detector. The thyristor that is turned on then automatically turns off after a full half cycle of its associated phase input. A full-wave rectifier couples the secondary winding of the transformer to the load so that the load capacitance is always charged with the same polarity.

  15. Weight Loss Nutritional Supplements

    NASA Astrophysics Data System (ADS)

    Eckerson, Joan M.

    Obesity has reached what may be considered epidemic proportions in the United States, not only for adults but for children. Because of the medical implications and health care costs associated with obesity, as well as the negative social and psychological impacts, many individuals turn to nonprescription nutritional weight loss supplements hoping for a quick fix, and the weight loss industry has responded by offering a variety of products that generates billions of dollars each year in sales. Most nutritional weight loss supplements are purported to work by increasing energy expenditure, modulating carbohydrate or fat metabolism, increasing satiety, inducing diuresis, or blocking fat absorption. To review the literally hundreds of nutritional weight loss supplements available on the market today is well beyond the scope of this chapter. Therefore, several of the most commonly used supplements were selected for critical review, and practical recommendations are provided based on the findings of well controlled, randomized clinical trials that examined their efficacy. In most cases, the nutritional supplements reviewed either elicited no meaningful effect or resulted in changes in body weight and composition that are similar to what occurs through a restricted diet and exercise program. Although there is some evidence to suggest that herbal forms of ephedrine, such as ma huang, combined with caffeine or caffeine and aspirin (i.e., ECA stack) is effective for inducing moderate weight loss in overweight adults, because of the recent ban on ephedra manufacturers must now use ephedra-free ingredients, such as bitter orange, which do not appear to be as effective. The dietary fiber, glucomannan, also appears to hold some promise as a possible treatment for weight loss, but other related forms of dietary fiber, including guar gum and psyllium, are ineffective.

  16. Advances in core loss calculations for magnetic materials

    NASA Technical Reports Server (NTRS)

    Triner, J. E.

    1982-01-01

    A new analytical technique which predicts the basic magnetic properties under various operating conditions encountered in state-of-the-art dc-ac/dc converters is discussed. Using a new flux-controlled core excitation circuit, magnetic core characteristics were developed for constant values of ramp flux (square wave voltage excitation) and frequency. From this empirical data, a mathematical loss characteristics equation is developed to analytically predict the specific core loss of several magnetic materials under various waveform excitation conditions. In addition, these characteristics show the circuit designer for the first time the direct functional relatonships between induction level and specific core loss as a function of the two key dc-dc converter operating parameters of input voltage and duty cycle.

  17. Avoiding personal data loss.

    PubMed

    Bergeron, B P

    1999-01-01

    The potential personal, financial, emotional, and professional costs associated with the loss of data stored in personal computing devices are difficult to appreciate a priori. Because of the potentially devastating consequences of significant data loss, it behooves all clinicians to take personal responsibility in securing their data, whether or not this responsibility is nominally assumed by Information Systems (IS) professionals. There are a variety of straightforward, easily implemented approaches that can be used to help secure personal data, including investigating IS department policies, following proper backing-up procedures, observing reasonable security precautions, keeping digital media current, and establishing a process for executing these approaches. PMID:10725050

  18. Volumetric Muscle Loss.

    PubMed

    Pollot, Beth E; Corona, Benjamin T

    2016-01-01

    Volumetric muscle loss (VML) injury is prevalent in severe extremity trauma and is an emerging focus area among orthopedic and regenerative medicine fields. VML injuries are the result of an abrupt, frank loss of tissue and therefore of different etiology from other standard rodent injury models to include eccentric contraction, ischemia reperfusion, crush, and freeze injury. The current focus of many VML-related research efforts is to regenerate the lost muscle tissue and thereby improve muscle strength. Herein, we describe a VML model in the anterior compartment of the hindlimb that is permissible to repeated neuromuscular strength assessments and is validated in mouse, rat, and pig. PMID:27492162

  19. Efficiency optimal control for AC drives with PWM inverters

    SciTech Connect

    Zach, F.C.; Ertl, H.

    1985-07-01

    For electrical drives using pulsewidth modulation (PWM) inverters and ac motors, methods for efficiency optimal control (EOC) have been developed. They are based on the most complete motor models, including such features as rotor skin effect. Furthermore, new solutions for selected harmonic elimination (SHE) are given. These new solutions come close to EOC. Also, it has been found that EOC solutions (although basically load-dependent as opposed to SHE) do not vary much with the motor used or the motor model applied. Even using a simple R-L series circuit as motor model does not change the solutions much. It is found that using the solutions gained from such a simple model is not more than two points off the real optimum based on a very complete motor model. (For this definition, the absolute harmonic loss minimum is given as zero points, the overall maximum as 100 points with a linear scale in between.) Therefore, one can use one EOC solution for all motors with sufficient accuracy, or, as second best solution, the new form of SHE. Therefore, the EOC solution can be judged load-independent. The implementation by microprocessor-based systems is as easy for other PWM methods. EOC for three and five switching angles per quarter period is discussed, as well as the new solutions for SHE for up to nine angles.

  20. Low Cost Fabrication of 2G Wires for AC Applications

    SciTech Connect

    Kodenkandath, T.; List, F.A., III

    2005-09-15

    Ink-jet printing has been demonstrated as an adaptable technology for printing YBCO filaments using a Metal Organic (MO) YBCO precursor. The technology was demonstrated using AMSC's proprietary metal organic TFA-based YBCO precursor and a commercial piezoelectric print-head on RABiTS templates. Filaments with a width of 100 um and spacing of 200 um were successfully printed, decomposed and processed to YBCO. Critical currents of {approx} 200 A/cm-w were achieved in a series of filaments with a 2 mm width. The single nozzle laboratory printer used in the Phase 1 program is capable of printing {approx} 100 um wide single filaments at a rate of 8-10 cm/sec. The electrical stabilization of filaments with a Ag ink was also evaluated using ink-jet printing. The overall objective of the Phase 1 Project was the evaluation and demonstration of inkjet-printing for depositing YBCO filaments on textured templates (RABiTS, IBAD, ISD, etc. substrates) with properties appropriate for low loss ac conductors. Goals of the Phase 1 program included development of an appropriate precursor ink, demonstration of the printing process, processing and characterization of printed YBCO filaments and evaluation of the process for further development.