Science.gov

Sample records for ac electro-osmotic aceo

  1. Ultrafast high-pressure AC electro-osmotic pumps for portable biomedical microfluidics.

    PubMed

    Huang, Chien-Chih; Bazant, Martin Z; Thorsen, Todd

    2010-01-01

    This paper details the development of an integrated AC electro-osmotic (ACEO) microfluidic pump for dilute electrolytes consisting of a long serpentine microchannel lined with three dimensional (3D) stepped electrode arrays. Using low AC voltage (1 V rms, 1 kHz), power (5 mW) and current (4.5 mA) in water, the pump is capable of generating a 1.3 kPa head pressure, a 100-fold increase over prior ACEO pumps, and a 1.3 mm/s effective slip velocity over the electrodes without flow reversal. The integrated ACEO pump can utilize low ionic strength solutions such as distilled water as the working solution to pump physiological strength (100 mM) biological solutions in separate microfluidic devices, with potential applications in portable or implantable biomedical microfluidic devices. As a proof-of-concept experiment, the use of the ACEO pumps for DNA hybridization in a microfluidic microarray is demonstrated. PMID:20024054

  2. Heat-transfer enhancement in AC electro-osmotic micro-flows

    NASA Astrophysics Data System (ADS)

    Liu, Z. P.; Speetjens, M. F. M.; Frijns, A. J. H.; van Steenhoven, A. A.

    2012-11-01

    Heat transfer in micro-flows is essential to emerging technologies as advanced microelectronics cooling systems and chemical processes in lab-on-a-chip applications. The present study explores the potential of AC electro-osmotic (ACEO) flow forcing, a promising technique for the actuation and manipulation of micro-flows, for heat-transfer enhancement. Subjects of investigation include the 3D flow structure due to ACEO forcing via an array of electrodes in a micro-channel by way of 3D velocity measurements. Presence and properties of vortical structures of the 3D flow are quantified in laboratory experiments. Typical outcomes of the experimental study result from a number of 3D particle trajectories obtained by using 3D micro-Particle-Tracking Velocimetry (3D μ-PTV). The steady nature of the flow enables combination of results from a series of measurements into one dense data set. This facilitates accurate evaluation of quantities relevant for heat transfer by data-processing methods. The primary circulation is given above one half of an electrode in terms of the spanwise component of vorticity. The outline of the vortex boundary is determined via the eigenvalues of the strain-rate tensor. To estimate convective heat transfer, wall shear rate above one half of an electrode is quantitatively analyzed as function of voltage amplitude and frequency. These results yield first insights into the characteristics of 3D ACEO flows and ways to exploit and manipulate them for heat-transfer enhancement.

  3. Fabrication and study of AC electro-osmotic micropumps

    NASA Astrophysics Data System (ADS)

    Guo, Xin

    In this thesis, microelectrode arrays of micropumps have been designed, fabricated and characterized for transporting microfluid by AC electro-osmosis (ACEO). In particular, the 3D stepped electrode design which shows superior performance to others in literature is adopted for making micropumps, and the performance of such devices has been studied and explored. A novel fabrication process has also been developed in the work, realizing 3D stepped electrodes on a flexible substrate, which is suitable for biomedical use, for example glaucoma implant. There are three major contributions to ACEO pumping in the work. First, a novel design of 3D "T-shaped" discrete electrode arrays was made using PolyMUMPsRTM process. The breakthrough of this work was discretizing the continuous 3D stepped electrodes which were commonly seen in the past research. The "T-shaped" electrodes did not only create ACEO flows on the top surfaces of electrodes but also along the side walls between separated electrodes. Secondly, four 3D stepped electrode arrays were designed, fabricated and tested. It was found from the experiment that PolyMUMPsRTM ACEO electrodes usually required a higher driving voltage than gold electrodes for operation. It was also noticed that a simulation based on the modified model taking into account the surface oxide of electrodes showed a better agreement with the experimental results. It thus demonstrated the possibility that the surface oxide of electrodes had impact on fluidic pumping. This methodology could also be applied to metal electrodes with a native oxide layer such as titanium and aluminum. Thirdly, a prototype of the ACEO pump with 3D stepped electrode arrays was first time realized on a flexible substrate using Kapton polyimide sheets and packaged with PDMS encapsulants. Comprehensive experimental testing was also conducted to evaluate the mechanical properties as well as the pumping performance. The experimental findings indicated that this fabrication

  4. Transport of particles and microorganisms in microfluidic channels using rectified ac electro-osmotic flow

    PubMed Central

    Wu, Wen-I; Selvaganapathy, P. Ravi; Ching, Chan Y.

    2011-01-01

    A new method is demonstrated to transport particles, cells, and other microorganisms using rectified ac electro-osmotic flows in open microchannels. The rectified flow is obtained by synchronous zeta potential modulation with the driving potential in the microchannel. Experiments were conducted to transport both neutral, charged particles, and microorganisms of various sizes. A maximum speed of 50 μm∕s was obtained for 8 μm polystyrene beads, without any electrolysis, using a symmetrical square waveform driving electric field of 5 V∕mm at 10 Hz and a 360 V gate potential with its polarity synchronized with the driving potential (phase lag=0°). PMID:21522497

  5. Simulation of an ac electro-osmotic pump with step microelectrodes

    NASA Astrophysics Data System (ADS)

    Kim, Byoung Jae; Lee, Seung-Hyun; Rezazadeh, Soghra; Sung, Hyung Jin

    2011-05-01

    Pumps with step microelectrodes subjected to an ac voltage are known to have faster pumping rates than those with planar asymmetric microelectrodes. The driving force for pumping in these systems is ac electro-osmosis. This paper aims to understand the flow behaviors of pumps with step microelectrodes by using a realistic model applicable to high external voltages. This model takes the steric effect due to the finite sizes of ions into account and copes with the exponential sensitivity of the counterion concentration to voltage. The effects on the pumping flow rate of varying the pump parameters were investigated. The geometrical parameters were optimized, and the effects of varying the ac frequency and amplitude were examined. The electrical potential of the fluid and the electrical charge at the electrode surface were solved simultaneously, and the Stokes equation was used to describe the fluid flow.

  6. Ionic Origin of Electro-osmotic Flow Hysteresis

    NASA Astrophysics Data System (ADS)

    Lim, Chun Yee; Lim, An Eng; Lam, Yee Cheong

    2016-02-01

    Electro-osmotic flow, the driving of fluid at nano- or micro- scales with electric field, has found numerous applications, ranging from pumping to chemical and biomedical analyses in micro-devices. Electro-osmotic flow exhibits a puzzling hysteretic behavior when two fluids with different concentrations displace one another. The flow rate is faster when a higher concentration solution displaces a lower concentration one as compared to the flow in the reverse direction. Although electro-osmotic flow is a surface phenomenon, rather counter intuitively we demonstrate that electro-osmotic flow hysteresis originates from the accumulation or depletion of pH-governing minority ions in the bulk of the fluid, due to the imbalance of electric-field-induced ion flux. The pH and flow velocity are changed, depending on the flow direction. The understanding of electro-osmotic flow hysteresis is critical for accurate fluid flow control in microfluidic devices, and maintaining of constant pH in chemical and biological systems under an electric field.

  7. Ionic Origin of Electro-osmotic Flow Hysteresis

    PubMed Central

    Lim, Chun Yee; Lim, An Eng; Lam, Yee Cheong

    2016-01-01

    Electro-osmotic flow, the driving of fluid at nano- or micro- scales with electric field, has found numerous applications, ranging from pumping to chemical and biomedical analyses in micro-devices. Electro-osmotic flow exhibits a puzzling hysteretic behavior when two fluids with different concentrations displace one another. The flow rate is faster when a higher concentration solution displaces a lower concentration one as compared to the flow in the reverse direction. Although electro-osmotic flow is a surface phenomenon, rather counter intuitively we demonstrate that electro-osmotic flow hysteresis originates from the accumulation or depletion of pH-governing minority ions in the bulk of the fluid, due to the imbalance of electric-field-induced ion flux. The pH and flow velocity are changed, depending on the flow direction. The understanding of electro-osmotic flow hysteresis is critical for accurate fluid flow control in microfluidic devices, and maintaining of constant pH in chemical and biological systems under an electric field. PMID:26923197

  8. Electro-osmotic transport in wet processing of textiles

    DOEpatents

    Cooper, J.F.

    1998-09-22

    Electro-osmotic (or electrokinetic) transport is used to efficiently force a solution (or water) through the interior of the fibers or yarns of textile materials for wet processing of textiles. The textile material is passed between electrodes that apply an electric field across the fabric. Used alone or in parallel with conventional hydraulic washing (forced convection), electro-osmotic transport greatly reduces the amount of water used in wet processing. The amount of water required to achieve a fixed level of rinsing of tint can be reduced, for example, to 1--5 lbs water per pound of fabric from an industry benchmark of 20 lbs water/lb fabric. 5 figs.

  9. Electro-osmotic transport in wet processing of textiles

    DOEpatents

    Cooper, John F.

    1998-01-01

    Electro-osmotic (or electrokinetic) transport is used to efficiently force a solution (or water) through the interior of the fibers or yarns of textile materials for wet processing of textiles. The textile material is passed between electrodes that apply an electric field across the fabric. Used alone or in parallel with conventional hydraulic washing (forced convection), electro-osmotic transport greatly reduces the amount of water used in wet processing. The amount of water required to achieve a fixed level of rinsing of tint can be reduced, for example, to 1-5 lbs water per pound of fabric from an industry benchmark of 20 lbs water/lb fabric.

  10. An analysis of electro-osmotic and magnetohydrodynamic heat pipes

    SciTech Connect

    Harrison, M.A.

    1988-01-01

    Mechanically simple methods of improving heat transport in heat pipes are investigated. These methods are electro-osmotic and magnetohydrodynamic augmentation. For the electro-osmotic case, a detailed electrokinetic model is used. The electrokinetic model used includes the effects of pore surface curvature and multiple ion diffusivities. The electrokinetic model is extended to approximate the effects of elevated temperature. When the electro-osmotic model is combined with a suitable heat-pipe model, it is found that the electro-osmotic pump should be a thin membrane. Arguments are provided that support the use of a volatile electrolyte. For the magnetohydrodynamic case, a brief investigation is provided. A quasi-one-dimensional hydromagnetic duct flow model is used. This hydromagnetic model is extended to approximate flow effects unique to heat pipes. When combined with a suitable heat pipe model, it is found that there is no performance gain for the case considered. In fact, there are serious pressure-distribution problems that have not been previously recognized. Potential solutions to these pressure-distribution problems are suggested.

  11. Electro-osmotically driven liquid delivery method and apparatus

    DOEpatents

    Rakestraw, D.J.; Anex, D.S.; Yan, C.; Dadoo, R.; Zare, R.N.

    1999-08-24

    Method and apparatus are disclosed for controlling precisely the composition and delivery of liquid at sub-{micro}L/min flow rate. One embodiment of such a delivery system is an electro-osmotically driven gradient flow delivery system that generates dynamic gradient flows with sub-{micro}L/min flow rates by merging a plurality of electro-osmotic flows. These flows are delivered by a plurality of delivery arms attached to a mixing connector, where they mix and then flow into a receiving means, preferably a column. Each inlet of the plurality of delivery arms is placed in a corresponding solution reservoir. A plurality of independent programmable high-voltage power supplies is used to apply a voltage program to each of the plurality of solution reservoirs to regulate the electro-osmotic flow in each delivery arm. The electro-osmotic flow rates in the delivery arms are changed with time according to each voltage program to deliver the required gradient profile to the column. 4 figs.

  12. Electro-osmotic infusion for joule heating soil remediation techniques

    DOEpatents

    Carrigan, Charles R.; Nitao, John J.

    1999-01-01

    Electro-osmotic infusion of ground water or chemically tailored electrolyte is used to enhance, maintain, or recondition electrical conductivity for the joule heating remediation technique. Induced flows can be used to infuse electrolyte with enhanced ionic conductivity into the vicinity of the electrodes, maintain the local saturation of near-electrode regions and resaturate a partially dried out zone with groundwater. Electro-osmotic infusion can also tailor the conductivity throughout the target layer by infusing chemically modified and/or heated electrolyte to improve conductivity contrast of the interior. Periodic polarity reversals will prevent large pH changes at the electrodes. Electro-osmotic infusion can be used to condition the electrical conductivity of the soil, particularly low permeability soil, before and during the heating operation. Electro-osmotic infusion is carried out by locating one or more electrodes adjacent the heating electrodes and applying a dc potential between two or more electrodes. Depending on the polarities of the electrodes, the induced flow will be toward the heating electrodes or away from the heating electrodes. In addition, electrodes carrying a dc potential may be located throughout the target area to tailor the conductivity of the target area.

  13. Electro-osmotically driven liquid delivery method and apparatus

    DOEpatents

    Rakestraw, David J.; Anex, Deon S.; Yan, Chao; Dadoo, Rajeev; Zare, Richard N.

    1999-01-01

    Method and apparatus for controlling precisely the composition and delivery of liquid at sub-.mu.L/min flow rate. One embodiment of such a delivery system is an electro-osmotically driven gradient flow delivery system that generates dynamic gradient flows with sub-.mu.L/min flow rates by merging a plurality of electro-osmotic flows. These flows are delivered by a plurality of delivery arms attached to a mixing connector, where they mix and then flow into a receiving means, preferably a column. Each inlet of the plurality of delivery arms is placed in a corresponding solution reservoir. A plurality of independent programmable high-voltage power supplies is used to apply a voltage program to each of the plurality of solution reservoirs to regulate the electro-osmotic flow in each delivery arm. The electro-osmotic flow rates in the delivery arms are changed with time according to each voltage program to deliver the required gradient profile to the column.

  14. Extensional instability in electro-osmotic microflows of polymer solutions

    NASA Astrophysics Data System (ADS)

    Bryce, R. M.; Freeman, M. R.

    2010-03-01

    Fluid transport in microfluidic systems typically is laminar due to the low Reynolds number characteristic of the flow. The inclusion of suspended polymers imparts elasticity to fluids, allowing instabilities to be excited when substantial polymer stretching occurs. For high molecular weight polymer chains we find that flow velocities achievable by standard electro-osmotic pumping are sufficient to excite extensional instabilities in dilute polymer solutions. We observe a dependence in measured fluctuations on polymer concentration which plateaus at a threshold corresponding to the onset of significant molecular crowding in macromolecular solutions; plateauing occurs well below the overlap concentration. Our results show that electro-osmotic flows of complex fluids are disturbed from the steady regime, suggesting potential for enhanced mixing and requiring care in modeling the flow of complex liquids such as biopolymer suspensions.

  15. Analysis of traveling-wave electro-osmotic pumping with double-sided electrode arrays

    NASA Astrophysics Data System (ADS)

    Yeh, Hung-Chun; Yang, Ruey-Jen; Luo, Win-Jet

    2011-05-01

    In this paper, a series of numerical simulations was performed to investigate the pumping performance of electro-osmotic micropumps containing electrode arrays patterned on the upper and lower sides of a microchannel. The simulations have been analyzed with a linear electro-osmotic model based upon the Debye-Hückel theory of the double layer. The potential drop across the diffuse layer is assumed to be less than 25 mV (kBT/e), and there is a linear response between the surface charge and the voltage drop across the double layer. The double layer is not resolved but is lumped into effective parameters that are imported from the Debye-Hückel and Stern layers. We examined the effects of the relative positioning of the electrodes in the opposing arrays (i.e., symmetrical or staggered), and the phase lag and the angular frequency of the alternating current (ac) signals applied to the electrodes within the two arrays. A critical height of the microchannel was observed, below which the interactions of the applied electrical potentials on the walls became significant. The optimum pumping effect was obtained when the electrode arrays were symmetrical to one another around the centerline of the channel and were activated by ac potentials with a 0° phase shift. The corresponding angular frequency of the maximum pumping velocity for different phase shifts of the applied ac signals was also determined. Overall, the simulation results presented in this paper provide a useful insight into the optimal design parameters and operating conditions for micropumps containing two arrays of microelectrodes on the microchannel walls.

  16. Fabrication of Out-of-Plane Electrodes for ACEO Pumps

    NASA Astrophysics Data System (ADS)

    Senousy, Yehya; Harnett, Cindy

    2012-02-01

    This abstract reports the fabrication process of a novel AC Electrosmosis (ACEO) pump with out of plane asymmetric interdigitated electrodes. A self-folding technique is used to fabricate the electrodes, that depends on the strain mismatch between the tensile stressed film (metal layer) and the compressive stress film (oxidized silicon layer). The electrodes roll up with a well-defined radius of curvature in the range of 100-200 microns. Two different electrical signals are connected to alternating electrodes using an insulating silicon nitride barrier that allows circuits to cross over each other without shorting. Electroosmotic micropumps are essential for low-cost, power-efficient microfluidic lab-on-chip devices used in diverse application such as analytical probes, drug delivery systems and surgical tools. ACEO pumps have been developed to address the drawbacks of the DCEO pumps such as the faradic reaction and gas bubbles. The original ACEO microfluidic pump was created with planar arrays of asymmetric interdigitated electrodes at the bottom of the channel. This rolled-up tube design improves on the planar design by including the channel walls and ceiling in the active pumping surface area of the device.

  17. Electro-osmotic flow in coated nanocapillaries: a theoretical investigation.

    PubMed

    Marini Bettolo Marconi, Umberto; Monteferrante, Michele; Melchionna, Simone

    2014-12-14

    Motivated by recent experiments, we present a theoretical investigation of how the electro-osmotic flow occurring in a capillary is modified when its charged surfaces are coated with charged polymers. The theoretical treatment is based on a three-dimensional model consisting of a ternary fluid-mixture, representing the solvent and two species for the ions, confined between two parallel charged plates decorated with a fixed array of scatterers representing the polymer coating. The electro-osmotic flow, generated by a constant electric field applied in a direction parallel to the plates, is studied numerically by means of Lattice Boltzmann simulations. In order to gain further understanding we performed a simple theoretical analysis by extending the Stokes-Smoluchowski equation to take into account the porosity induced by the polymers in the region adjacent to the walls. We discuss the nature of the velocity profiles by focusing on the competing effects of the polymer charges and the frictional forces they exert. We show evidence of the flow reduction and of the flow inversion phenomenon when the polymer charge is opposite to the surface charge. By using the density of polymers and the surface charge as control variables, we propose a phase diagram that discriminates the direct and the reversed flow regimes and determines their dependence on the ionic concentration. PMID:25343500

  18. Electro-osmotic flow enhancement in carbon nanotube membranes.

    PubMed

    Mattia, Davide; Leese, Hannah; Calabrò, Francesco

    2016-02-13

    In this work, experimental evidence of the presence of electro-osmotic flow (EOF) in carbon nanotube membranes with diameters close to or in the region of electrical double layer overlap is presented for two different electrolytes for the first time. No EOF in this region should be present according to the simplified theoretical framework commonly used for EOF in micrometre-sized channels. The simplifying assumptions concern primarily the electrolyte charge density structure, based on the Poisson-Boltzmann (P-B) equation. Here, a numerical analysis of the solutions for the simplified case and for the nonlinear and the linearized P-B equations is compared with experimental data. Results show that the simplified solution produces a significant deviation from experimental data, whereas the linearized solution of the P-B equation can be adopted with little error compared with the full P-B case. This work opens the way to using electro-osmotic pumping in a wide range of applications, from membrane-based ultrafiltration and nanofiltration (as a more efficient alternative to mechanical pumping at the nanoscale) to further miniaturization of lab-on-a-chip devices at the nanoscale for in vivo implantation. PMID:26712647

  19. Electro-osmotic drag coefficient of water and methanol in polymer electrolytes at elevated temperatures

    SciTech Connect

    Weng, D.; Wainright, J.S.; Landau, U.; Savinell, R.F.

    1996-04-01

    The electro-osmotic drag coefficient of water in two polymer electrolytes was experimentally determined as a function of water activity and current density for temperatures up to 200 C. The results show that the electro-osmotic drag coefficient varies from 0.2 to 0.6 in Nafion{reg_sign}/H{sub 3}PO{sub 4} membrane electrolyte, but is essentially zero in phosphoric acid-doped PBI (polybenzimidazole) membrane electrolyte over the range of water activity considered. The near-zero electro-osmotic drag coefficient found in PBI indicates that this electrolyte should lessen the problems associated with water redistribution in proton exchange membrane fuel cells.

  20. Electro-Osmotic Remediation of Fine-Grained Sediments

    SciTech Connect

    Cherepy, N.J.; McNab, W.W.; Wildenschild, D.; Ruiz, R.; Elsholz, A.

    1999-11-22

    The coupled-flow phenomenon, electro-osmosis, whereby water flow results from an applied electrical potential gradient, is being used at Lawrence Livermore National Laboratory to induce water flow through deep (25-40 meters below surface) fine-grained sediments. The scoping work described here lays the groundwork for implementation of this technology to remediate solvent-contaminated clayey zones at the LLNL site. The electro-osmotic conductivity (k{sub e}) measured in-situ between two 37 m deep wells, 3 m apart of 2.3 x 10{sup -9} m{sup 2}/s-V is in good agreement with the value determined from bench-top studies on the core extracted from one of the wells of 0.94 {+-} 0.29 x 10{sup -9} m{sup 2}/s-V. Hydraulic conductivity (k{sub h}) of the same core is measured to be 2.03 {+-} 0.36 x 10{sup -10} m/s. Thus, a voltage gradient of 1 V/cm produces an effective hydraulic conductivity of {approx}1 x 10{sup -7} m/s; an increase in conductivity of nearly three orders of magnitude.

  1. Electro-osmotic flow in a rotating rectangular microchannel

    PubMed Central

    Ng, Chiu-On; Qi, Cheng

    2015-01-01

    An analytical model is presented for low-Rossby-number electro-osmotic flow in a rectangular channel rotating about an axis perpendicular to its own. The flow is driven under the combined action of Coriolis, pressure, viscous and electric forces. Analytical solutions in the form of eigenfunction expansions are developed for the problem, which is controlled by the rotation parameter (or the inverse Ekman number), the Debye parameter, the aspect ratio of the channel and the distribution of zeta potentials on the channel walls. Under the conditions of fast rotation and a thin electric double layer (EDL), an Ekman–EDL develops on the horizontal walls. This is essentially an Ekman layer subjected to electrokinetic effects. The flow structure of this boundary layer as a function of the Ekman layer thickness normalized by the Debye length is investigated in detail in this study. It is also shown that the channel rotation may have qualitatively different effects on the flow rate, depending on the channel width and the zeta potential distributions. Axial and secondary flows are examined in detail to reveal how the development of a geostrophic core may lead to a rise or fall of the mean flow. PMID:26345088

  2. Modulating Electro-osmotic Flow with Polymer Coatings

    NASA Astrophysics Data System (ADS)

    Hickey, Owen A.

    Micro- and nano-fluidic devices represent an exciting field with a wide range of possible applications. These devices, typically made of either silica or glass, ionize when placed in contact with water. Upon the application of an electric field parallel to the wall, a flow is produced by the charged walls called the electro-osmotic flow (EOF). Since electric fields are so often used as the driving force in these devices, EOF is an extremely common phenomenon. For this reason it is highly desirable to be able to control EOF in order to optimize the functioning of these devices. One method which is quite common experimentally is the modification of the surface using polymer coatings. These coatings can be either adsorbed or grafted, and charged or neutral. The first part of this thesis looks at the role of neutral adsorbed polymer coatings for the modulation of EOF. Specifically our simulation results show that for adsorbed coatings made from a dilute polymer solution the strongest quenching of EOF is found for an adsorption strength at the phase transition for adsorption of the polymers. Further evidence is presented that shows that by using a high density of polymer solution and a polymer which has a strong attraction to the surface a very thick polymer layer can be created. Next the case of charged grafted polymer coatings is examined. The variation of the EOF with respect to several key parameters which characterize the polymer coating is investigated and compared to theory. The prediction that the electrophoretic velocity of the polymers is the same as the EOF generated by a coating made up of the same polymers is found to be false though the two values are quite close. The last section presents results which show how hydrodynamic interactions in charged polymer systems can be modeled mesoscopically without the use of explicit charges by forcing a slip between monomers and the surrounding fluid. This model is validated by simulating some surprising predictions

  3. Analytical and numerical study of the electro-osmotic annular flow of viscoelastic fluids.

    PubMed

    Ferrás, L L; Afonso, A M; Alves, M A; Nóbrega, J M; Pinho, F T

    2014-04-15

    In this work we present semi-analytical solutions for the electro-osmotic annular flow of viscoelastic fluids modeled by the Linear and Exponential PTT models. The viscoelastic fluid flows in the axial direction between two concentric cylinders under the combined influences of electrokinetic and pressure forcings. The analysis invokes the Debye-Hückel approximation and includes the limit case of pure electro-osmotic flow. The solution is valid for both no slip and slip velocity at the walls and the chosen slip boundary condition is the linear Navier slip velocity model. The combined effects of fluid rheology, electro-osmotic and pressure gradient forcings on the fluid velocity distribution are also discussed.

  4. Applications of Electro-Osmotic Transport in the Processing of Textiles

    SciTech Connect

    Cooper, J.F.; Krueger, R.; Hopper, R.; Cherepy, N.

    1999-11-29

    We report development of a pilot process for the industrial rinsing of fabrics. This process combines hydraulic (pressure-driven) transport with electro-osmotic transport. It reduces the total amount of water required in certain rinsing operations by a factor of about five. Cotton exhibits an electro-osmotic transport coefficient of about 6 x 10{sup -9} m{sup 2}/s-V resulting from a partial ionization of hydroxyl groups on the cellulose polymer substrate. This process applies a field transverse to the fabric to effect the movement of water in the spaces between the 10 {micro}m cotton fibers which constitute the yam. The field strength is adjusted so that the induced electro-osmotic flux is comparable to a pressure-driven flux, which moves preferentially in the more open channels between the yams. For a fixed current density, solution conductivity and electro-osmotic transport vary inversely. The process is most practical for removal of liquids of relatively low conductivity (<500 {micro}S/cm). For removal of solutions of conductivity greater than 1200 {micro}S/cm, the rate of electro-osmotic flow may be too low to benefit the rinsing process if current densities are restricted to practical levels of about 30 mA/cm{sup 2}. Electra-osmotic transport may have important applications in wet processing of extremely fine textiles, such as micro fiber fabrics. In addition to rinsing, electro-osmotic transport may also be used to speed the penetration of chemicals and dyestuffs that are applied to the surface of wet textiles.

  5. Development of polymeric coatings for control of electro-osmotic flow in ASTP MA-011 electrophoresis technology experiment

    NASA Technical Reports Server (NTRS)

    Patterson, W. J.

    1976-01-01

    The development of a methyl cellulose based coating system for control of electro-osmotic flow at the walls of electrophoresis cells is described. Flight electrophoresis columns were coated with this system, resulting in a flight set of six columns. In flight photography of MA-011 electrophoretic separations verified control of electro-osmotic flow.

  6. Electrolyte management for effective long-term electro-osmotic transport in low-permeability soils.

    PubMed

    Cherepy, Nerine J; Wildenschild, Dorthe

    2003-07-01

    Electro-osmosis, a coupled-flow phenomenon in which an applied electrical potential gradient drives water flow, may be used to induce water flow through fine-grained sediments. Test cell measurements of electro-osmotic transport in clayey cores extracted from the 27-31 m depth range of the Lawrence Livermore National Laboratory site indicate the importance of pH control within the anode and cathode reservoirs. In our first experiment, pH was not controlled. As a result, carbonate precipitation and metals precipitation occurred near the cathode end of the core, with acidification near the anode. The combination of these acid and base reactions led to the decline of electro-osmotic flow by a factor of 2 in less than one pore volume. In a second experiment, long-term water transport (>21 pore volumes) at stable electro-osmotic conductivity (k(eo) approximately 1 x 10(-9) m2/s-V) was effected with anode reservoir pH > 8, and cathode reservoir pH < 6. Hydraulic conductivity (k(h)) of the same core was 4 x 10(-10) m/s under a 0.07 MPa hydraulic gradient without electro-osmosis. Stable electro-osmotic flow was measured at a velocity of 4 x 10(-7) m/s under a 4 V/cm voltage gradient, and no hydraulic gradient-3 orders of magnitude greater than the hydraulic flow. We also observed chloroform production in the anode reservoir, resulting from electrochemical production of chlorine gas reacting with trace organics. The chloroform was transported electro-osmotically to the cathode, without measurable loss to adsorption, volatilization, or degradation. PMID:12875410

  7. Swelling and electro-osmotic properties of cation-exchange membranes with different structures in methanol-water media

    NASA Astrophysics Data System (ADS)

    Barragán, V. M.; Villaluenga, J. P. G.; Godino, M. P.; Izquierdo-Gil, M. A.; Ruiz-Bauzá, C.; Seoane, B.

    Electro-osmosis experiments through three cation-exchange membranes with different morphology and similar electric properties have been performed using methanol-water solutions under different experimental conditions. The influence on the electro-osmotic transport of the percentage of methanol on solvent with two different electrolytes, NaCl and LiCl, has been studied. The experimental results show that the presence of methanol in the solutions affects strongly the electro-osmotic flow, and this influence is different depending on the membrane morphology. Correlations among electro-osmotic permeability, swelling behavior, and cell resistance are studied for these membrane systems at different percentages of methanol in solvent.

  8. Electro-osmotic drag effect on the methanol permeation for sulfonated poly(ether ether ketone) and nafion 117 membranes.

    PubMed

    Chi, Nguyen Thi Que; Bae, Byungchan; Kim, Dukjoon

    2013-11-01

    Electro-osmotic drag effect on the methanol permeation was investigated for sulfonated poly(ether ether ketone) (sPEEK) membrane, and its result was compared with that of Nafion 117 membrane. The electro-osmotic drag coefficient was determined from the limiting current density measured at different temperature. The methanol permeability of sPEEK membrane increased with temperature but its temperature dependence was not as strong as that of Nafion 117 membrane. The methanol permeability or the total methanol flux of Nafion 117 membrane was at least twice higher than that of sPEEK70 membrane (sPEEK membrane with 70% sulfonation degree), as the methanol permeation was highly contributed by the electro-osmotic drag effect. This higher electro-osmotic drag of Nafion 117 membrane is attributed to the bigger ion cluster and waster channel in nanophase and thus more free water absorption than sPEEK membrane.

  9. Submarine hydro-electro-osmotic power plants for an efficient exploitation of salinity gradients

    NASA Astrophysics Data System (ADS)

    Reali, M.

    1981-03-01

    An energy-conversion scheme, which allows efficient exploitation of salinity gradients, is proposed. This is a submarine hydro-electro-osmotic power plant in which fresh surface water is conveyed through a penstock to a submerged hydraulic turbine for the generation of electric power. The water leaves the turbine outlet depressurized and finally diffuses out in the sea, by osmosis, through a semipermeable barrier.

  10. Separation of ions in nanofluidic channels with combined pressure-driven and electro-osmotic flow.

    PubMed

    Gillespie, Dirk; Pennathur, Sumita

    2013-03-01

    Separation of ionic species with the same electrophoretic mobility but different valence in electrolyte systems can occur within nanometer-scale channels with finite electrical double layers (EDLs). This is because EDL thicknesses are a significant fraction of slit height in such channels and can create transverse analyte concentration profiles that allow for unique separation modalities when combined with axial fluid flow. Previous work has shown such separation to occur using either pressure-driven flow or electro-osmotic flow separately. Here, we develop a Poisson-Boltzmann model to compare the separation of such ions using the combination of both pressure-driven and electro-osmotic flow. Applying a pressure gradient in the opposite direction of electro-osmotic flow can allow for zero or infinite retention of analyte species, which we investigate using three different wall boundary conditions. Furthermore, we determine conditions in fused silica nanochannels with which to generate optimal separation between two analytes of different charge but the same mobility. We also give simple rules of thumb to achieve the best separation efficacy in nanochannel systems.

  11. Transition zone dynamics in combined isotachophoretic and electro-osmotic transport

    NASA Astrophysics Data System (ADS)

    Schönfeld, Friedhelm; Goet, Gabriele; Baier, Tobias; Hardt, Steffen

    2009-09-01

    The present study focuses on the interplay of isotachophoresis (ITP) and electro-osmotic flow (EOF). While EOF is commonly suppressed in ITP applications, we investigate scenarios of the combination of both EOF and ITP. Experimental results of ITP/EOF experiments within cross-patterned polymer chips show characteristic deformations of fluorescent sample zones sandwiched between leading and trailing electrolytes. A changing curvature of the deformation is observed during ITP/EOF runs, but overall a well defined sample segment is maintained after a transport over a few centimeters. By means of numerical modeling we study the deformation attributed to the mismatch of EOF between leading and trailing electrolytes. The model results are found to qualitatively agree with our experimental findings. We introduce the ratio of the EOF velocities in the leading and trailing electrolyte, expressed via the respective mobilities, as a dimensionless parameter γ and show that in the case where electro-osmotically induced convection dominates over electromigration the deformation width scales as 1-γ. In particular, we find that the EOF-induced dispersion virtually vanishes for the case γ =1. Hence, in this particular case isotachophoretic self-sharpening and electro-osmotic pumping can be combined without any detrimental effects on sample transport even for large EOF velocities.

  12. Analytical solution of two-fluid electro-osmotic flows of viscoelastic fluids.

    PubMed

    Afonso, A M; Alves, M A; Pinho, F T

    2013-04-01

    This paper presents an analytical model that describes a two-fluid electro-osmotic flow of stratified fluids with Newtonian or viscoelastic rheological behavior. This is the principle of operation of an electro-osmotic two-fluid pump as proposed by Brask et al. [Tech. Proc. Nanotech., 1, 190-193, 2003], in which an electrically non-conducting fluid is transported by the interfacial dragging viscous force of a conducting fluid that is driven by electro-osmosis. The electric potential in the conducting fluid and the analytical steady flow solution of the two-fluid electro-osmotic stratified flow in a planar microchannel are presented by assuming a planar interface between the two immiscible fluids with Newtonian or viscoelastic rheological behavior. The effects of fluid rheology, shear viscosity ratio, holdup and interfacial zeta potential are analyzed to show the viability of this technique, where an enhancement of the flow rate is observed as the shear-thinning effects are increased.

  13. Electro-osmotic pumping and ion-concentration polarization based on conical nanopores

    NASA Astrophysics Data System (ADS)

    Yeh, Hung-Chun; Chang, Chih-Chang; Yang, Ruey-Jen

    2015-06-01

    A numerical investigation is performed into the characteristics of an electro-osmotic pump consisting of a negatively charged conical nanopore. It is shown that the dependence of the flow rectification effect on the bias direction is the reverse of that of the ion current rectification effect. Moreover, the nozzle mode (i.e., the bias is applied from the base side of the nanopore to the tip side) has a higher flow rate compared to the diffuser mode (i.e., the bias is applied from the tip side of the nanopore to the base side). The results showed that the ion-concentration polarization effect occurred inside the conical nanopore, resulting in surface conduction dominating in the ionic current. The ions inside the nanopore are depleted and enriched under the nozzle mode and the diffuser mode, respectively. As a result, the electro-osmotic pump yields a greater pumping pressure, flow rate, and energy conversion efficiency when operating in the nozzle mode. In addition, we also investigated the flow rate rectification behavior for the conical nanopore. The best flow rate rectification factor in this work is 2.06 for an electrolyte concentration of 10-3M .

  14. Influence of atomistic physics on electro-osmotic flow: An analysis based on density functional theory

    NASA Astrophysics Data System (ADS)

    Nilson, Robert H.; Griffiths, Stewart K.

    2006-10-01

    Molecular density profiles and charge distributions determined by density functional theory (DFT) are used in conjunction with the continuum Navier-Stokes equations to compute electro-osmotic flows in nanoscale channels. The ion species of the electrolyte are represented as centrally charged hard spheres, and the solvent is treated as a dense fluid of neutral hard spheres having a uniform dielectric constant. The model explicitly accounts for Lennard-Jones interactions among fluid and wall molecules, hard sphere repulsions, and short range electrical interactions, as well as long range Coulombic interactions. Only the last of these interactions is included in classical Poisson-Boltzmann (PB) modeling of the electric field. Although the proposed DFT approach is quite general, the sample calculations presented here are limited to symmetric monovalent electrolytes. For a prescribed surface charge, this DFT model predicts larger counterion concentrations near charged channel walls, relative to classical PB modeling, and hence smaller concentrations in the channel center. This shifting of counterions toward the walls reduces the effective thickness of the Debye layer and reduces electro-osmotic velocities as compared to classical PB modeling. Zeta potentials and fluid speeds computed by the DFT model are as much as two or three times smaller than corresponding PB results. This disparity generally increases with increasing electrolyte concentration, increasing surface charge density and decreasing channel width. The DFT results are found to be comparable to those obtained by molecular dynamics simulation, but require considerably less computing time.

  15. Electro-osmotic fluxes in multi-well electro-remediation processes.

    PubMed

    López-Vizcaíno, Rubén; Sáez, Cristina; Mena, Esperanza; Villaseñor, Jose; Cañizares, Pablo; Rodrigo, Manuel A

    2011-01-01

    In recent years, electrokinetic techniques on a laboratory scale have been studied but few applications have been assessed at full-scale. In this work, a mock-up plant with two rows of three electrodes positioned in semipermeable electrolyte wells has been used to study the electro-osmotic flux distribution. Water accumulated in the cathodic wells when an electric voltage gradient was applied between the two electrode-well rows. Likewise, slight differences in the water flux were observed depending on the position and number of electrodes used and on the voltage gradient applied. Results show that the electro-osmotic flow did not increase proportionally with the number of electrodes used. During the start-up of the study, there was an abrupt change in the current density, pH and conductivity of the soil portions closest to electrodic wells due to electrokinetic processes. These differences can be explained in terms of the complex current distributions from anode and cathode rows. PMID:22029697

  16. Electro-osmotic fluxes in multi-well electro-remediation processes.

    PubMed

    López-Vizcaíno, Rubén; Sáez, Cristina; Mena, Esperanza; Villaseñor, Jose; Cañizares, Pablo; Rodrigo, Manuel A

    2011-01-01

    In recent years, electrokinetic techniques on a laboratory scale have been studied but few applications have been assessed at full-scale. In this work, a mock-up plant with two rows of three electrodes positioned in semipermeable electrolyte wells has been used to study the electro-osmotic flux distribution. Water accumulated in the cathodic wells when an electric voltage gradient was applied between the two electrode-well rows. Likewise, slight differences in the water flux were observed depending on the position and number of electrodes used and on the voltage gradient applied. Results show that the electro-osmotic flow did not increase proportionally with the number of electrodes used. During the start-up of the study, there was an abrupt change in the current density, pH and conductivity of the soil portions closest to electrodic wells due to electrokinetic processes. These differences can be explained in terms of the complex current distributions from anode and cathode rows.

  17. Nanometer-thick lateral polyelectrolyte micropatterns induce macrosopic electro-osmotic chaotic fluid instabilities.

    PubMed

    Wessling, M; Morcillo, L Garrigós; Abdu, S

    2014-01-01

    Electro-convective vortices in ion concentration polarization under shear flow have been of practical relevance for desalination processes using electrodialysis. The phenomenon has been scientifically disregarded for decades, but is recently embraced by a growing fluid dynamics community due its complex superposition of multi-scale gradients in electrochemical potential and space charge interacting with emerging complex fluid momentum gradients. While the visualization, quantification and fundamental understanding of the often-chaotic fluid dynamics is evolving rapidly due to sophisticated simulations and experimentation, little is known whether these instabilities can be induced and affected by chemical topological heterogeneity in surface properties. In this letter, we report that polyelectrolyte layers applied as micropatterns on ion exchange membranes induce and facilitate the electro-osmotic fluid instabilities. The findings stimulate a variety of fundamental questions comparable to the complexity of today's turbulence research.

  18. Laboratory Investigation of Electro-Osmotic Remediation of Fine-Grained Sediments

    SciTech Connect

    Cherepy, N.; Wildenschild, D.; Elsholz, A.

    2000-02-23

    Electro-osmosis, a coupled-flow phenomenon in which an applied electrical potential gradient drives water flow, may be used to induce water flow through fine-grained sediments. We plan to use this technology to remediate chlorinated solvent-contaminated clayey zones at the LLNL site. The electro-osmotic conductivity (k{sub e}) determined from bench-top studies for a core extracted from a sediment zone 36.4-36.6 m below surface was initially 7.37 x 10{sup -10} m{sup 2}/s-V, decreasing to 3.44 x 10{sup -10} m{sup 2}/s-V, after electro-osmotically transporting 0.70 pore volumes of water through it (195 ml). Hydraulic conductivity (k{sub h}) of the same core was initially measured to be 5.00 x 10{sup -10} m/s, decreasing to 4.08 x 10{sup -10} m/s at the end of processing. This decline in permeability is likely due to formation of a chemical precipitation zone within the core. Water splitting products and ions electromigrate and precipitate within the core; H{sup +} and metal cations migrate toward the cathode, and OH{sup -} from the cathode moves toward the anode. We are now exploring how to minimize this effect using pH control. The significance of this technology is that for this core, a 3 V/cm voltage gradient produced an initial effective hydraulic conductivity of 2.21 x 10{sup -7} m/s, >400x greater than the initial hydraulic conductivity.

  19. Experimental and theoretical investigations of non-Newtonian electro-osmotic driven flow in rectangular microchannels.

    PubMed

    Huang, Yi; Chen, Juzheng; Wong, TeckNeng; Liow, Jong-Leng

    2016-07-20

    With the development of microfluidics, electro-osmotic (EO) driven flow has gained intense research interest as a result of its unique flow profile and the corresponding benefits in its application in the transportation of sensitive samples. Sensitive samples, such as DNA, are incapable of enduring strong flow shear induced by conventional hydrodynamic driven methods. EO driven flow is thus a niche area. However, even though there are a few research studies focusing on bio-fluidic samples related to EO driven flow, the majority of them are merely theoretical modeling without solid evidence from experiments due to the inherent complex rheological behavior of the bio-fluids. Challenges occur when the EO driven mechanism meets with complex rheology; vital questions such as can the zeta potential still be assumed to be constant when dealing with fluids with complex rheology? and "Does the shear thinning effect enhance electro-osmotic driven flow?" need to be answered. We conducted experiments using current monitoring and microscopy fluorescence methods, and developed a theoretical model by coupling a generalized Smoluchowski approach with the power-law constitutive model. We calculated the zeta potential and compared the experimental results with modeling to answer the questions. The results show a reduction of zeta potential in the presence of PEO aqueous solutions. A constant zeta potential is also indicated by varying the PEO concentration and the electric field strength.The shear thinning effect is also addressed via experimental data and theoretical calculations. The results show a promising enhancement of the EO driven velocity due to the shear thinning effect. PMID:27381295

  20. A novel microfluidic valve controlledby induced charge electro-osmotic flow

    NASA Astrophysics Data System (ADS)

    Wang, Chengfa; Song, Yongxin; Pan, Xinxiang; Li, Dongqing

    2016-07-01

    In this paper, a novel microfluidic valve by utilizing induced charge electro-osmotic flow (ICEOF) is proposed and analyzed. The key part of the microfluidic valve is a Y-shaped microchannel. A small metal plate is placed at each corner of the junction of the Y-shaped microchannel. When a DC electrical field is applied through the channels, electro-osmotic flows occur in the channels, and two vortices will be formed near each of the metal plates due to the ICEOF. The two vortices behave like virtual ‘blocking columns’ to restrain and direct the flow in the Y-channel. In this paper, effects of the length of the metal plates, the applied voltages, the width of the microchannel, the zeta potential of the non-metal microchannel wall, and the orientation of the branch channels on the flow switching between two outlet channels are numerically investigated. The results show that the flow switching between the two outlet channels can be flexibly achieved by adjusting the applied DC voltages. The critical switching voltage (CSV), under which one outlet channel is closed, decreases with the increase in the metal plate length and the orientation angle of the outlet channels. The CSV, however, increases with the increase in the inlet voltage, the width of the microchannel, and the absolute value of the zeta potential of the non-metal microchannel wall. Compared with other types of micro-valves, the proposed micro-valve is simple in structure without any moving parts. Only a DC power source is needed for its actuation, thus it can operate automatically by controlling the applied voltages.

  1. Oscillatory electro-osmotic flow through a slit channel with slipping stripes on walls

    NASA Astrophysics Data System (ADS)

    Chu, Henry C. W.; Ng, Chiu-On

    2013-04-01

    A theoretical model is presented in this paper for time-oscillating electro-osmotic flow through a plane channel bounded by two parallel plates, which are patterned with periodic stripes of distinct hydrodynamic slippage and wall potential. The flow is driven by oscillatory pressure gradient and electric field of the same frequency in the axial direction. Flows that are longitudinal or transverse to the stripes are investigated. Based on the Debye-Hückel approximation, and assuming Stokes flow, the electric potential and the velocity fields are found by the methods of eigenfunction expansion and point collocation. The phenomenological coefficients of the Onsager relations for the fluid and current fluxes are deduced as functions of the channel height, the area fraction of wall with slippage, the intrinsic slip length, the Debye parameter, the zeta potentials and the oscillation parameter. Considering several kinds of wall patterns, we extend the theoretical limits in the steady-flow regime to the oscillatory-flow regime. For a uniformly charged wall, the effective slip length obtained from the hydrodynamic problem can still be used directly in the electro-osmotic flow as if the wall were uniformly slipping. When the slipping stripes are perfectly slipping but uncharged, the presence of such stripes will always have a decreasing effect on the streaming conductance, unlike the steady case in which it gives no net effect on the flow in the limit of a very thin double layer. Furthermore, we confirm the presence of a threshold frequency, beyond which the flow will diminish significantly. The slipping fraction of the wall will always introduce a phase lag to the response and lower the threshold frequency. Increasing the wall potential in the presence of slippage can appreciably increase the streaming conductance and the phase lag.

  2. Numerical study of active control of mixing in electro-osmotic flows by temperature difference using lattice Boltzmann methods.

    PubMed

    Alizadeh, A; Wang, J K; Pooyan, S; Mirbozorgi, S A; Wang, M

    2013-10-01

    In this paper, the effect of temperature difference between inlet flow and walls on the electro-osmotic flow through a two-dimensional microchannel is investigated. The main objective is to study the effect of temperature variations on the distribution of ions and consequently internal electric potential field, electric body force, and velocity fields in an electro-osmotic flow. We assume constant temperature and zeta potential on walls and use the mean temperature of each cross section to characterize the Boltzmann ion distribution across the channel. Based on these assumptions, the multiphysical transports are still able to be described by the classical Poisson-Boltzmann model. In this work, the Navier-Stokes equation for fluid flow, the Poisson-Boltzmann equation for ion distribution, and the energy equation for heat transfer are solved by a couple lattice Boltzmann method. The modeling results indicate that the temperature difference between walls and the inlet solution may lead to two symmetrical vortices at the entrance region of the microchannel which is appropriate for mixing enhancements. The advantage of this phenomenon for active control of mixing in electro-osmotic flow is the manageability of the vortex scale without extra efforts. For instance, the effective domain of this pattern could broaden by the following modulations: decreasing the external electric potential field, decreasing the electric double layer thickness, or increasing the temperature difference between inlet flow and walls. This work may provide a novel strategy for design or optimization of microsystems. PMID:23859813

  3. Nongassing long-lasting electro-osmotic pump with polyaniline-wrapped aminated graphene electrodes.

    PubMed

    Kumar, Rudra; Jahan, Kousar; Nagarale, Rajaram K; Sharma, Ashutosh

    2015-01-14

    An efficient nongassing electro-osmotic pump (EOP) with long-lasting electrodes and exceptionally stable operation is developed by using novel flow-through polyaniline (PANI)-wrapped aminated graphene (NH2-G) electrodes. The NH2-G/PANI electrode combines the excellent oxidation/reduction capacity of PANI with the exceptional conductivity and inertness of NH2-G. The flow rate varies linearly with voltage but is highly dependent on the electrode composition. The flow rates at a potential of 5 V for pristine NH2-G and PANI electrodes are 71 and 100 μL min(-1) cm(-2), respectively, which increase substantially by the use of NH2-G/PANI electrode. It increased from 125 to 182 μL min(-1) cm(-2) as the fraction of aniline increased from 66.63 to 90.90%. The maximum flux obtained is 40 μL min(-1) V(-1) cm(-2) with NH2-G/PANI-90.9 electrodes. The assembled EOP remained exceptionally stable until the electrode columbic capacity was fully utilized. The prototype shown here delivered 8.0 μL/min at a constant applied voltage of 2 V for over 7 h of continuous operation. The best EOP produces a maximum stall pressure of 3.5 kPa at 3 V. These characteristics make it suitable for a variety of microfluidic/device applications.

  4. Flow patterning in Hele-Shaw configurations using non-uniform electro-osmotic slip

    NASA Astrophysics Data System (ADS)

    Boyko, Evgeniy; Rubin, Shimon; Gat, Amir D.; Bercovici, Moran

    2015-10-01

    We present an analytical study of electro-osmotic flow in a Hele-Shaw configuration with non-uniform zeta potential distribution. Applying the lubrication approximation and assuming thin electric double layer, we obtain a pair of uncoupled Poisson equations for the pressure and depth-averaged stream function, and show that the inhomogeneous parts in these equations are governed by gradients in zeta potential parallel and perpendicular to the applied electric field, respectively. We obtain a solution for the case of a disk-shaped region with uniform zeta potential and show that the flow field created is an exact dipole, even in the immediate vicinity of the disk. In addition, we study the inverse problem where the desired flow field is known and solve for the zeta potential distribution required in order to establish it. Finally, we demonstrate that such inverse problem solutions can be used to create directional flows confined within narrow regions, without physical walls. Such solutions are equivalent to flow within channels and we show that these can be assembled to create complex microfluidic networks, composed of intersecting channels and turns, which are basic building blocks in microfluidic devices.

  5. Electro-osmotic-based catholyte production by Microbial Fuel Cells for carbon capture.

    PubMed

    Gajda, Iwona; Greenman, John; Melhuish, Chris; Santoro, Carlo; Li, Baikun; Cristiani, Pierangela; Ieropoulos, Ioannis

    2015-12-01

    In Microbial Fuel Cells (MFCs), the recovery of water can be achieved with the help of both active (electro-osmosis), and passive (osmosis) transport pathways of electrolyte through the semi-permeable selective separator. The electrical current-dependent transport, results in cations and electro-osmotically dragged water molecules reaching the cathode. The present study reports on the production of catholyte on the surface of the cathode, which was achieved as a direct result of electricity generation using MFCs fed with wastewater, and employing Pt-free carbon based cathode electrodes. The highest pH levels (>13) of produced liquid were achieved by the MFCs with the activated carbon cathodes producing the highest power (309 μW). Caustic catholyte formation is presented in the context of beneficial cathode flooding and transport mechanisms, in an attempt to understand the effects of active and passive diffusion. Active transport was dominant under closed circuit conditions and showed a linear correlation with power performance, whereas osmotic (passive) transport was governing the passive flux of liquid in open circuit conditions. Caustic catholyte was mineralised to a mixture of carbonate and bicarbonate salts (trona) thus demonstrating an active carbon capture mechanism as a result of the MFC energy-generating performance. Carbon capture would be valuable for establishing a carbon negative economy and environmental sustainability of the wastewater treatment process.

  6. Electro-osmotically driven MHD flow and heat transfer in micro-channel

    NASA Astrophysics Data System (ADS)

    Shit, G. C.; Mondal, A.; Sinha, A.; Kundu, P. K.

    2016-05-01

    A theoretical analysis is presented for electro-osmotic flow (EOF) of blood in a hydrophobic micro-channel with externally applied magnetic field. The lumen of micro-channels is assumed to be porous medium in addition to the consideration of permeability of the channel walls. The effects of slip velocity and thermal-slip are taken into consideration. The governing equations in the electrical double layer (EDL) together with the Poisson-Boltzmann equation and the body force exerted by the applied potential are furthermore considered. The flow is governed by the non-Newtonian viscoelastic fluid model. These equations along with the thermal energy equation are approximated by assuming that the channel height is much greater than the thickness of electrical double layer consisting the stern and diffusive layers. The problem is solved analytically and the computed results have presented graphically for various values of the dimensionless parameters. The results presented here have significant impact on the therapeutic treatment in hyperthermia as well as in controlling blood flow and heat transfer in micro-channels.

  7. Electro-osmotic-based catholyte production by Microbial Fuel Cells for carbon capture.

    PubMed

    Gajda, Iwona; Greenman, John; Melhuish, Chris; Santoro, Carlo; Li, Baikun; Cristiani, Pierangela; Ieropoulos, Ioannis

    2015-12-01

    In Microbial Fuel Cells (MFCs), the recovery of water can be achieved with the help of both active (electro-osmosis), and passive (osmosis) transport pathways of electrolyte through the semi-permeable selective separator. The electrical current-dependent transport, results in cations and electro-osmotically dragged water molecules reaching the cathode. The present study reports on the production of catholyte on the surface of the cathode, which was achieved as a direct result of electricity generation using MFCs fed with wastewater, and employing Pt-free carbon based cathode electrodes. The highest pH levels (>13) of produced liquid were achieved by the MFCs with the activated carbon cathodes producing the highest power (309 μW). Caustic catholyte formation is presented in the context of beneficial cathode flooding and transport mechanisms, in an attempt to understand the effects of active and passive diffusion. Active transport was dominant under closed circuit conditions and showed a linear correlation with power performance, whereas osmotic (passive) transport was governing the passive flux of liquid in open circuit conditions. Caustic catholyte was mineralised to a mixture of carbonate and bicarbonate salts (trona) thus demonstrating an active carbon capture mechanism as a result of the MFC energy-generating performance. Carbon capture would be valuable for establishing a carbon negative economy and environmental sustainability of the wastewater treatment process. PMID:26343045

  8. Robust monolithic silica-based on-chip electro-osmotic micro-pump.

    PubMed

    Nie, Fu-Qiang; Macka, Mirek; Barron, Leon; Connolly, Damian; Kent, Nigel; Paull, Brett

    2007-05-01

    A robust, compact, on-chip, electro-osmotic micro-pump (EOP) for micro-flow analysis, based on parallel, encased, 10 x 0.1 mm I.D. monolithic silica capillary columns has been developed. A 15 x 40 x 2 mm poly(methyl methacrylate) (PMMA) chip, containing a total of nine parallel EOP systems was fabricated, allowing the use of single, double or triple monolithic columns to produce increased flow as required. The monolithic silica was compatible with both aqueous and organic solvents without swelling or shrinking problems, with the triple column EOP capable of generating flow of up to 0.6 microL min(-1) under zero pressure load and over 0.1 microL min(-1) with an applied pressure of ca. 2.4 bar using an applied voltage of just 2 kV. Current generated at the 2 kV applied voltage for a 2 mM acetate buffer solution (pH 4.5) was under 4 microA, allowing stable, bubble-free flow. The developed triple column EOP was incorporated within a micro-fluidic chip (5.0 x 2.0 x 0.4 cm) integrated with a second single 10 x 0.1 mm column EOP, for combined sample injection and simple on-chip micro-flow analysis.

  9. Non-isothermal electro-osmotic flow in a microchannel with charge-modulated surfaces

    NASA Astrophysics Data System (ADS)

    Bautista, Oscar; Sanchez, Salvador; Mendez, Federico

    2015-11-01

    In this work, we present an theoretical analysis of a nonisothermal electro-osmotic flow of a Newtonian fluid over charge-modulated surfaces in a microchannel. Here, the heating in the microchannel is due to the Joule effect caused by the imposition of an external electric field. The study is conducted through the use of perturbation techniques and is validated by means of numerical simulations. We consider that both, viscosity and electrical conductivity of the fluid are temperature-dependent; therefore, in order to determine the heat transfer process and the corresponding effects on the flow field, the governing equations of continuity, momentum, energy and electric potential have to be solved in a coupled manner. The principal obtained results evidence that the flow patterns are perturbed in a noticeable manner in comparison with the isothernal case. Our results may be used for increasing microfluidics mixing by conjugating thermal effects with the use of charge-modulated surfaces. This work has been supported by the research grants no. 220900 of Consejo Nacional de Ciencia y Tecnología (CONACYT) and 20150919 of SIP-IPN at Mexico. F. Méndez acknowledges also the economical support of PAPIIT-UNAM under contract number IN112215.

  10. [Magnetic Fe₃O₄Microparticles Conditioning-Pressure Electro-osmotic Dewatering (MPEOD) of Sewage Sludge].

    PubMed

    Qian, Xu; Wang, Yi-li; Zhao, Li

    2016-05-15

    For magnetic Fe₃O₄ microparticles conditioning--pressure electro-osmotic dewatering (MPEOD) process of activated sludge (AS), the effects of operating parameters (optimal dosage of Fe₃O₄, electric field duration, mechanical pressure and voltage) on the dewatering efficiency and energy consumption were investigated, and the optimal conditions were determined. Moreover, the properties of supernatant and sludge along MPEOD process were studied as well as the interaction force between the sludge biosolids. Taking the energy consumption into consideration, the results showed that the optimal dewatering effect for AS could be achieved with a magnetic Fe₃O₄ microparticles dosage of 0.15 g · g⁻¹, an electric field duration of 2 h, a mechanical pressure of 400-600 kPa and a voltage of 30-50 V. When MPEOD was conducted at 400 kPa and 50 V for 2 h, the sludge reduction rate reached 98.30%, the percentage of water removal was 99.34% and the moisture content of AS decreased from 99.18% to 44.46%. The corresponding consumption of energy was 0.013 3 kW · h · kg⁻¹. The coagulation mechanism played a slight role in the AS conditioning with magnetic Fe₃O₄ micro-particles. In fact, magnetic Fe₃O₄micro-particles could greatly decrease the acid-base interaction (WA) between AS biosolids, cause floc growth and enlarge pores in AS aggregates, which will be beneficial to AS dewatering. Compared to DLVO theory, the extended DLVO theory could accurately describe the aggregation and dispersion behavior of sludge particles.

  11. [Magnetic Fe₃O₄Microparticles Conditioning-Pressure Electro-osmotic Dewatering (MPEOD) of Sewage Sludge].

    PubMed

    Qian, Xu; Wang, Yi-li; Zhao, Li

    2016-05-15

    For magnetic Fe₃O₄ microparticles conditioning--pressure electro-osmotic dewatering (MPEOD) process of activated sludge (AS), the effects of operating parameters (optimal dosage of Fe₃O₄, electric field duration, mechanical pressure and voltage) on the dewatering efficiency and energy consumption were investigated, and the optimal conditions were determined. Moreover, the properties of supernatant and sludge along MPEOD process were studied as well as the interaction force between the sludge biosolids. Taking the energy consumption into consideration, the results showed that the optimal dewatering effect for AS could be achieved with a magnetic Fe₃O₄ microparticles dosage of 0.15 g · g⁻¹, an electric field duration of 2 h, a mechanical pressure of 400-600 kPa and a voltage of 30-50 V. When MPEOD was conducted at 400 kPa and 50 V for 2 h, the sludge reduction rate reached 98.30%, the percentage of water removal was 99.34% and the moisture content of AS decreased from 99.18% to 44.46%. The corresponding consumption of energy was 0.013 3 kW · h · kg⁻¹. The coagulation mechanism played a slight role in the AS conditioning with magnetic Fe₃O₄ micro-particles. In fact, magnetic Fe₃O₄micro-particles could greatly decrease the acid-base interaction (WA) between AS biosolids, cause floc growth and enlarge pores in AS aggregates, which will be beneficial to AS dewatering. Compared to DLVO theory, the extended DLVO theory could accurately describe the aggregation and dispersion behavior of sludge particles. PMID:27506042

  12. Rotating electro-osmotic flow over a plate or between two plates.

    PubMed

    Chang, Chien-Cheng; Wang, Chang-Yi

    2011-11-01

    In this paper, we investigate rotating electro-osmotic (EO) flow over an infinite plate or in a channel formed by two parallel plates. The analysis is based on the Debye-Hückel approximation for charge distributions and the Navier-Stokes equation for a transport electrolyte in the rotating frame. It is shown that, for the single plate, the nondimensional speed of system rotation ω is the singly most important parameter, while for the channel, in addition to ω, the nondimensional electrokinetic width K also plays an important role. However, the parameter ω≡η(2) has different natural appearances in the respective cases of a single plate (SP) and two plates (TPs). More precisely, η(SP) measures the ratio λ(D)/L(K) of the Debye length to the Ekman depth, while η(TP) measures the ratio L/L(K) of the channel width to the Ekman depth. The effect of rotation is always to reduce the axial flow rate along the direction of the applied electric field, accompanied by a (secondary) transverse flow. In the SP case, the plot on the velocity plane for each ω shows an interesting closed EO Ekman spiral. The size of the spiral shrinks with increasing ω. The transverse flow is so significant that the volume transport associated with the EO Ekman spiral turns clockwise 45° to the applied field near ω=0 and gradually turns at a right angle to the applied field as ω is increased. In contrast, in the TP case, the transverse flow rate is smaller than the axial flow rate when ω is small. The transverse flow rates at all K are observed to reach their maxima at ω of order 1. The volume transport is nearly at a zero angle to the applied field near ω=0 and gradually turns to 45° to the applied field as ω is increased. In the limit of ω→∞, for both SP and TP cases, the entire system forms a rigid body rotation-there is neither axial nor transverse flow. PMID:22181511

  13. Rotating electro-osmotic flow over a plate or between two plates

    NASA Astrophysics Data System (ADS)

    Chang, Chien-Cheng; Wang, Chang-Yi

    2011-11-01

    In this paper, we investigate rotating electro-osmotic (EO) flow over an infinite plate or in a channel formed by two parallel plates. The analysis is based on the Debye-Hückel approximation for charge distributions and the Navier-Stokes equation for a transport electrolyte in the rotating frame. It is shown that, for the single plate, the nondimensional speed of system rotation ω is the singly most important parameter, while for the channel, in addition to ω, the nondimensional electrokinetic width K also plays an important role. However, the parameter ω≡η2 has different natural appearances in the respective cases of a single plate (SP) and two plates (TPs). More precisely, η(SP) measures the ratio λD/LK of the Debye length to the Ekman depth, while η(TP) measures the ratio L/LK of the channel width to the Ekman depth. The effect of rotation is always to reduce the axial flow rate along the direction of the applied electric field, accompanied by a (secondary) transverse flow. In the SP case, the plot on the velocity plane for each ω shows an interesting closed EO Ekman spiral. The size of the spiral shrinks with increasing ω. The transverse flow is so significant that the volume transport associated with the EO Ekman spiral turns clockwise 45° to the applied field near ω=0 and gradually turns at a right angle to the applied field as ω is increased. In contrast, in the TP case, the transverse flow rate is smaller than the axial flow rate when ω is small. The transverse flow rates at all K are observed to reach their maxima at ω of order 1. The volume transport is nearly at a zero angle to the applied field near ω=0 and gradually turns to 45° to the applied field as ω is increased. In the limit of ω→∞, for both SP and TP cases, the entire system forms a rigid body rotation—there is neither axial nor transverse flow.

  14. Phenomenological theory of electro-osmotic effect and water management in polymer electrolyte proton-conducting membranes

    SciTech Connect

    Eikerling, M.; Kornyshev, A.A.; Kharkats, Yu.I.; Volfkovich, Yu.M.

    1998-08-01

    Partial dehydration of the proton-conducting membrane under working conditions is one of the major problems in low-temperature fuel cell technology. In this paper a model, which accounts for the electro-osmotically induced drag of water from anode to cathode and the counterflow in a hydraulic pressure gradient is proposed. A balance of these flows determines a gradient of water content across the membrane, which causes a decline of the current-voltage performance. Phenomenological transport equations coupled with the capillary pressure isotherm are used, involving the conductivity, permeability, and electro-osmotic drag coefficients dependent on the local water content. The effects of membrane parameters on current-voltage performance are investigated. A universal feature of the obtained current-voltage plots is the existence of a critical current at which the potential drop across the membrane increases dramatically due to the dehydration of membrane layers close to the anode. For a membrane with zero residual conductivity in its dry parts, the critical current is a limiting current. Well below the critical current the effect of dehydration is negligible and the current-voltage plot obeys Ohm`s law. The shape of the capillary pressure isotherm determines the nonohmic corrections. A comparison of the results of this study to those of the pertinent diffusion-type models reveals qualitatively different features, the convection model is found to be closer to experimental observations.

  15. EFFECT OF AQUEOUS PHASE PROPERTIES ON CLAY PARTICLE ZETA POTENTIAL AND ELECTRO-OSMOTIC PERMEABILITY: IMPLICATIONS FOR ELECTRO-KINETIC SOIL REMEDIATION PROCESSES

    EPA Science Inventory

    The influence of aqueous phase properties (pH, ionic strength and divalent metal ion concentration) on clay particle zeta potential and packed-bed electro-osmotic permeability was quantified. Although pH strongly altered the zeta potential of a Georgia kaolinite, it did not signi...

  16. Mixing enhancement of low-Reynolds electro-osmotic flows in microchannels with temperature-patterned walls.

    PubMed

    Alizadeh, A; Zhang, L; Wang, M

    2014-10-01

    Mixing becomes challenging in microchannels because of the low Reynolds number. This study aims to present a mixing enhancement method for electro-osmotic flows in microchannels using vortices caused by temperature-patterned walls. Since the fluid is non-isothermal, the conventional form of Nernst-Planck equation is modified by adding a new migration term which is dependent on both temperature and internal electric potential gradient. This term results in the so-called thermo-electrochemical migration phenomenon. The coupled Navier-Stokes, Poisson, modified Nernst-Planck, energy and advection-diffusion equations are iteratively solved by multiple lattice Boltzmann methods to obtain the velocity, internal electric potential, ion distribution, temperature and species concentration fields, respectively. To enhance the mixing, three schemes of temperature-patterned walls have been considered with symmetrical or asymmetrical arrangements of blocks with surface charge and temperature. Modeling results show that the asymmetric arrangement scheme is the most efficient scheme and enhances the mixing of species by 39% when the Reynolds number is on the order of 10(-3). Current results may help improve the design of micro-mixers at low Reynolds number.

  17. Ion exclusion and electrokinetic effects resulting from electro-osmotic flow of salt solutions in charged silica nanopores.

    PubMed

    Haria, Neil R; Lorenz, Christian D

    2012-05-01

    Silica nanopores are the focus of significant scientific interest due to their potential in a wide variety of applications including desalination membranes. In this paper, the results of extensive all-atom molecular dynamics simulations of the electro-osmotic flow of 0.5 M monovalent (NaCl) and divalent (CaCl(2)) ionic solutions through cylindrical charged silica nanopores are presented. The silica nanopores are produced such that they capture the experimentally observed interfacial properties. The results provide an atomistic description of the ion transport through pores of diameters of 1.5 nm, 2.0 nm, 2.5 nm and 3.0 nm. In doing so, the effect of pore size on ion pairing, ion hydration, and water orientation for each ionic solution was investigated. Also, the transport of the ions through the nanopores is studied, and it is found that in the monovalent solutions the Cl(-) ions are excluded from the nanopores of all sizes. Whereas in the divalent solutions, there is no such preferential exclusion of either ion. This is due to the fact that the interfacial charge is fully compensated for by the Ca(2+) ions while it is not the case for the Na(+) ions.

  18. Mixing enhancement of low-Reynolds electro-osmotic flows in microchannels with temperature-patterned walls.

    PubMed

    Alizadeh, A; Zhang, L; Wang, M

    2014-10-01

    Mixing becomes challenging in microchannels because of the low Reynolds number. This study aims to present a mixing enhancement method for electro-osmotic flows in microchannels using vortices caused by temperature-patterned walls. Since the fluid is non-isothermal, the conventional form of Nernst-Planck equation is modified by adding a new migration term which is dependent on both temperature and internal electric potential gradient. This term results in the so-called thermo-electrochemical migration phenomenon. The coupled Navier-Stokes, Poisson, modified Nernst-Planck, energy and advection-diffusion equations are iteratively solved by multiple lattice Boltzmann methods to obtain the velocity, internal electric potential, ion distribution, temperature and species concentration fields, respectively. To enhance the mixing, three schemes of temperature-patterned walls have been considered with symmetrical or asymmetrical arrangements of blocks with surface charge and temperature. Modeling results show that the asymmetric arrangement scheme is the most efficient scheme and enhances the mixing of species by 39% when the Reynolds number is on the order of 10(-3). Current results may help improve the design of micro-mixers at low Reynolds number. PMID:24984071

  19. Dependence of buffer acidity and surfactant chain-length on electro-osmotic mobility in thermoplastic microchannels.

    PubMed

    Wang, Shau-Chun; Lee, Chia-Yu; Chen, Hsiao-Ping

    2005-04-15

    In this paper, we report the dependence of buffer pH and coating surfactant chain-length on electro-osmotic (EO) mobility in co-polyester microchannels. Thermoplastics co-polyester hydrolyzes to anionic functionality to create electrical double layer on the micro-channel walls. These negatively charged sites are partially or completely screened when long-chain surfactants are added into the buffer. This ancillary technique to modify surface charge polarity to avoid analyte adsorption is known as dynamic coating. We develop a theory to predict the EO mobility tendency on buffer acidity considering the combination of pH-dependent surfactant aggregation and surface dissociation. Our findings of pH-dependent EO mobility in coated channels, using three types of quaternary ammonium surfactants, lauryltrimethyammonium bromide (LTAB), trimethyl (tetradecyl) ammonium bromide (TTAB), and cetyltrimethyammonium bromide (CTAB), agree with our theoretical prediction. We also explain the chain-length dependence of mobility with a collaborative adsorption mechanism of surfactant aggregates.

  20. An electro-osmotic micro-pump based on monolithic silica for micro-flow analyses and electro-sprays.

    PubMed

    Chen, Zilin; Wang, Ping; Chang, Hsueh-Chia

    2005-06-01

    A high-pressure electro-osmotic micro-pump fabricated by a sol-gel process is reported as a fluid-driving unit in a flow-injection analysis (FIA) system. The micro FIA system consists of a monolithic micro-pump on a glass slide (2.5 x 7.5 cm), a micro-injector, and a micro-sensor (2.5 x 1.5 cm). The monolithic silica matrix has a continuous skeleton morphology with micrometer-sized through-pores. The micrometer-size pores with a large negative surface charge density build up a large pressure under a DC electric field to drive fluid through the downstream units. A novel Nafion joint for the downstream cathode eliminates flow into the electrode reservoir and further enhances pressure build-up. The measured pump-pressure curve indicated a maximum pressure of 0.4 MPa at flow rate of 0.4 microL min(-1) at 6 kV. Despite the large voltage, the small current transmission area through the monolith produced a negligible current (less than 100 microA) that did not generate bubbles or ion contaminants. The flow rate can be precisely controlled in the range 200 nL to 2.5 microL min(-1) by varying the voltage from 1 to 6 kV. The high pump pressure and the large current-free DC field also enabled the pump to act as an electro-spray interface with a downstream analytical instrument.

  1. Induced- and alternating-current electro-osmotic control of the diffusion layer growth in a microchannel-membrane interface device

    NASA Astrophysics Data System (ADS)

    Park, Sinwook; Yossifon, Gilad

    2014-11-01

    The passage of an electric current through an ionic permselective medium under an applied electric field is characterized by the formation of ionic concentration gradients, which result in regions of depleted and enriched ionic concentration at opposite ends of the medium. Induced-current electro-osmosis (ICEO) and alternating-current-electro-osmosis (ACEO) are shown to control the growth of the diffusion layer (DL) which, in turn, controls the diffusion limited ion transport through the microchannel-membrane system. We fabricated and tested devices made of a Nafion membrane connecting two opposite PDMS microchannels. An interdigitated electrode array was embedded within the microchannel with various distances from the microchannel-membrane interface. The induced ICEO (floating electrodes) / ACEO (active electrodes) vortices formed at the electrode array stir the fluid and thereby suppress the growth of the DL. The intensity of the ACEO vortices is controlled by either varying the voltage amplitude or the frequency, each having its own unique effect. Enhancement of the limiting current by on-demand control of the diffusion length is of importance in on-chip electro-dialysis, desalination and preconcentration of analytes.

  2. Dielectrophoretic particle-particle interaction under AC electrohydrodynamic flow conditions.

    PubMed

    Lee, Doh-Hyoung; Yu, Chengjie; Papazoglou, Elisabeth; Farouk, Bakhtier; Noh, Hongseok M

    2011-09-01

    We used the Maxwell stress tensor method to understand dielectrophoretic particle-particle interactions and applied the results to the interpretation of particle behaviors under alternating current (AC) electrohydrodynamic conditions such as AC electroosmosis (ACEO) and electrothermal flow (ETF). Distinct particle behaviors were observed under ACEO and ETF. Diverse particle-particle interactions observed in experiments such as particle clustering, particles keeping a certain distance from each other, chain and disc formation and their rotation, are explained based on the numerical simulation data. The improved understanding of particle behaviors in AC electrohydrodynamic flows presented here will enable researchers to design better particle manipulation strategies for lab-on-a-chip applications. PMID:21823132

  3. Development of a bi-functional silica monolith for electro-osmotic pumping and DNA clean-up/extraction using gel-supported reagents in a microfluidic device.

    PubMed

    Oakley, Jennifer A; Shaw, Kirsty J; Docker, Peter T; Dyer, Charlotte E; Greenman, John; Greenway, Gillian M; Haswell, Stephen J

    2009-06-01

    A silica monolith used to support both electro-osmotic pumping (EOP) and the extraction/elution of DNA coupled with gel-supported reagents is described. The benefits of the combined EOP extraction/elution system were illustrated by combining DNA extraction and gene amplification using the polymerase chain reaction (PCR) process. All the reagents necessary for both processes were supported within pre-loaded gels that allow the reagents to be stored at 4 degrees C for up to four weeks in the microfluidic device. When carrying out an analysis the crude sample only needed to be hydrodynamically introduced into the device which was connected to an external computer controlled power supply via platinum wire electrodes. DNA was extracted with 65% efficiency after loading lysed cells onto a silica monolith. Ethanol contained within an agarose gel matrix was then used to wash unwanted debris away from the sample by EOP (100 V cm(-1) for 5 min). The retained DNA was subsequently eluted from the monolith by water contained in a second agarose gel, again by EOP using an electric field of 100 V cm(-1) for 5 min, and transferred into the PCR reagent containing gel. The eluted DNA in solution was successfully amplified by PCR, confirming that the concept of a complete self-contained microfluidic device could be realised for DNA sample clean up and amplification, using a simple pumping and on-chip reagent storage methodology.

  4. Electro-osmotic flow of power-law fluid and heat transfer in a micro-channel with effects of Joule heating and thermal radiation

    NASA Astrophysics Data System (ADS)

    Shit, G. C.; Mondal, A.; Sinha, A.; Kundu, P. K.

    2016-11-01

    A mathematical model has been developed for studying the electro-osmotic flow and heat transfer of bio-fluids in a micro-channel in the presence of Joule heating effects. The flow of bio-fluid is governed by the non-Newtonian power-law fluid model. The effects of thermal radiation and velocity slip condition have been examined in the case of hydrophobic channel. The Poisson-Boltzmann equation governing the electrical double layer field and a body force generated by the applied electric potential field are taken into consideration. The results presented here pertain to the case where the height of the channel is much greater than the thickness of electrical double layer comprising the Stern and diffuse layers. The expressions for flow characteristics such as velocity, temperature, shear stress and Nusselt number have been derived analytically under the purview of the present model. The results estimated on the basis of the data available in the existing scientific literatures are presented graphically. The effects of thermal radiation have an important bearing on the therapeutic procedure of hyperthermia, particularly in understanding the heat transfer in micro-channel in the presence of electric potential. The dimensionless Joule heating parameter has a reducing impact on Nusselt number for both pseudo-plastic and dilatant fluids, nevertheless its impact on Nusselt number is more pronounced for dilatant fluid. Furthermore, the effect of viscous dissipation has a significant role in controlling heat transfer and should not be neglected.

  5. Effect of interfacial Maxwell stress on time periodic electro-osmotic flow in a thin liquid film with a flat interface.

    PubMed

    Mayur, Manik; Amiroudine, Sakir; Lasseux, Didier; Chakraborty, Suman

    2014-03-01

    Electro-osmotic flows (EOF) have seen remarkable applications in lab-on-a-chip based microdevices owing to their lack of moving components, durability, and nondispersive nature of the flow profiles under specifically designed conditions. However, such flows may typically suffer from classical Faradaic artifacts like electrolysis of the solvent, which affects the flow rate control. Such a problem has been seen to be overcome by employing time periodic EOFs. Electric field induced transport of a conductive liquid is another nontrivial problem that requires careful study of interfacial dynamics in response to such an oscillatory flow actuation. The present study highlights the role of electric field generated Maxwell stress and free surface potential along with the electric double layer thickness and forcing frequency, toward influencing the interfacial transport and fluid flow in free-surface electro-osmosis under a periodically varying external electric field, in a semi-analytical formalism. Our results reveal interesting regimes over which the pertinent interfacial phenomena as well as bulk transport characteristics may be favorably tuned by employing time varying electrical fields. PMID:24123086

  6. Enhanced penetration of fluoride particles into bovine enamel by combining dielectrophoresis with AC electroosmosis.

    PubMed

    Ivanoff, Chris S; Swami, Nathan S; Hottel, Timothy L; Garcia-Godoy, Franklin

    2013-11-01

    Fluoride deposition into the pores of enamel is necessary at high concentrations to reduce enamel demineralization and with a high degree of penetration to account for loss by ingestion. Current diffusion and electrochemical methods are inadequate for effectively transporting fluoride greater than 20 μm into enamel. The study explores the coupling of dielectrophoresis (DEP) and AC electroosmosis (ACEO) to selectively concentrate fluoride particles from fluoride gel excipients and enhance their penetration into enamel. By measuring the frequency response of approximately 10-μm-sized sodium fluoride particles in an aqueous gel media, appropriate frequencies for positive DEP, negative DEP, and ACEO are identified. An assembly composed of two cross-planar interdigitated electrode (IDE) arrays with open slots is driven successively by fields at appropriate frequencies to drive fluoride particles through the slots of the IDE and into the enamel pores using a combination of DEP and ACEO methods. Fluoride uptake and penetration of 1.23% acidulated phosphate fluoride gel into bovine tooth enamel at various depths is measured using wavelength dispersive spectrometry to compare deposition by diffusion, DEP, and DEP plus ACEO. Fluoride levels in all DEP groups were significantly higher than diffusion groups at depths 10 and 20 μm. The highest fluoride concentrations at 10, 20, 50, and 100 μm depths occur under deposition conditions combining DEP with ACEO. Fluoride levels at 50 μm were equivalent to long-term prophylactic exposure. These methods may potentially benefit populations at high risk for development of caries and periodontal disease, including underserved children and disparate groups. PMID:23897721

  7. Programmable Electro Osmotic Lab on a Chip

    NASA Astrophysics Data System (ADS)

    Class, Andreas G.

    2014-11-01

    We propose to use a 2D check-board patterned surface with alternating zeta potential made of semiconductors and individually controllable electrodes surrounding each field to drive by electro osmosis an arbitrary flow along the surface within the cavity of a lab-on-a-chip. In contrast to other fluid mechanic devices the flow is not driven by pressure gradients but rather by a controllable fluid velocity within the Debay boundary layer. Thus fluid is transported like a parcel on a conveyor belt. The use of alternating zeta potential fields and alternating electrode polarities allows to transport flow along multiple fields without the need to increase voltage. Basic functionality of the chip is accomplished by appropriate programming: fluid transport along straight and curved path, merging and splitting flow paths, flow crossing by red light traffic control, and mixing. Implementing sensors for electric resistance on the Lab-On-A-Chip allows to program a diagnosis application using electrophoresis for detection. Transport within the Lab-On-A-Chip can be described by Stokes-flow subject to the boundary conditions given by asymptotic theory in the thin-Debay-layer-limit describing field driven electro kinetic effects.

  8. Electro-osmotic flows in rectangular cavities

    NASA Astrophysics Data System (ADS)

    Meleshko, Viatcheslav; Trofimchuk, Alexandre; Gourjii, Alexandre; Bezym'yana, Elina

    2010-11-01

    The talk presents the results of investigation of the microfluidics mixing processes in a rectangular cavity flows induced by elctro-osmotic excitation. Enhanced mixing plays an important role in biological and chemical pharmaceutics analysis in microfluidics systems. Analytical solution is presented for the velocity field in the cavity under various electric potential distributions. The location of the periodic points in the flow are accurately established and the structure of stable and unstable manifolds is discussed. The optimal form of excitation is suggested in order to obtain most effective mixing regime in the cavity. The regular and chaotic regions are identified under various condition of excitation. Finally, we compare numerical and analytical solutions with the results of laboratory experiments for real microfluidic flows.

  9. Combination of ac electroosmosis and dielectrophoresis for particle manipulation on electrically-induced microscale wave structures

    NASA Astrophysics Data System (ADS)

    Chung, Cheng-Che; Glawdel, Tomasz; Ren, Carolyn L.; Chang, Hsien-Chang

    2015-03-01

    This work presents a simple method to fabricate controllable microscale wave structures on the top of regular interdigitated electrode (IDE) arrays using electrically-assisted lithography techniques. Smooth wave structures are extremely difficult, if not impossible, to fabricate using traditional multilayer photolithography technology. The fabricated wave structures were carefully measured using an optical profiler and the measured wave profiles were used in the numerical simulation of electrical field and for evaluating the parameters influencing the fabricated wave structure. It is demonstrated that the combined smooth wave structure and IDE array offer unique capability for particle manipulation including particle concentration, aggregation and separation. Particle motion manipulated via the combined wave structure and IDE array is governed by ac electroosmosis (ACEO), dielectrophoresis (DEP) or a combination of both depending on the applied frequency. At lower frequencies (~30 kHz), ACEO dominates and particles are driven to move along the valleys of the wave structures; while at higher frequencies (~200 kHz), DEP force dominates which concentrates particles at the peaks of the wave structures. In addition, varying the ac waveform from sine-wave to square-wave allows for dynamic control of particle motion. Size-dependent particle separation over the wave structure is also demonstrated for a mixture of 0.5 µm and 2 µm particles that are separated into two populations by the joint effects of drag and DEP forces when being pumped to flow via ACEO.

  10. Strongly nonlinear dynamics of electrolytes in large ac voltages.

    PubMed

    Højgaard Olesen, Laurits; Bazant, Martin Z; Bruus, Henrik

    2010-07-01

    We study the response of a model microelectrochemical cell to a large ac voltage of frequency comparable to the inverse cell relaxation time. To bring out the basic physics, we consider the simplest possible model of a symmetric binary electrolyte confined between parallel-plate blocking electrodes, ignoring any transverse instability or fluid flow. We analyze the resulting one-dimensional problem by matched asymptotic expansions in the limit of thin double layers and extend previous work into the strongly nonlinear regime, which is characterized by two features--significant salt depletion in the electrolyte near the electrodes and, at very large voltage, the breakdown of the quasiequilibrium structure of the double layers. The former leads to the prediction of "ac capacitive desalination" since there is a time-averaged transfer of salt from the bulk to the double layers, via oscillating diffusion layers. The latter is associated with transient diffusion limitation, which drives the formation and collapse of space-charge layers, even in the absence of any net Faradaic current through the cell. We also predict that steric effects of finite ion sizes (going beyond dilute-solution theory) act to suppress the strongly nonlinear regime in the limit of concentrated electrolytes, ionic liquids, and molten salts. Beyond the model problem, our reduced equations for thin double layers, based on uniformly valid matched asymptotic expansions, provide a useful mathematical framework to describe additional nonlinear responses to large ac voltages, such as Faradaic reactions, electro-osmotic instabilities, and induced-charge electrokinetic phenomena.

  11. Strongly nonlinear dynamics of electrolytes in large ac voltages

    NASA Astrophysics Data System (ADS)

    Højgaard Olesen, Laurits; Bazant, Martin Z.; Bruus, Henrik

    2010-07-01

    We study the response of a model microelectrochemical cell to a large ac voltage of frequency comparable to the inverse cell relaxation time. To bring out the basic physics, we consider the simplest possible model of a symmetric binary electrolyte confined between parallel-plate blocking electrodes, ignoring any transverse instability or fluid flow. We analyze the resulting one-dimensional problem by matched asymptotic expansions in the limit of thin double layers and extend previous work into the strongly nonlinear regime, which is characterized by two features—significant salt depletion in the electrolyte near the electrodes and, at very large voltage, the breakdown of the quasiequilibrium structure of the double layers. The former leads to the prediction of “ac capacitive desalination” since there is a time-averaged transfer of salt from the bulk to the double layers, via oscillating diffusion layers. The latter is associated with transient diffusion limitation, which drives the formation and collapse of space-charge layers, even in the absence of any net Faradaic current through the cell. We also predict that steric effects of finite ion sizes (going beyond dilute-solution theory) act to suppress the strongly nonlinear regime in the limit of concentrated electrolytes, ionic liquids, and molten salts. Beyond the model problem, our reduced equations for thin double layers, based on uniformly valid matched asymptotic expansions, provide a useful mathematical framework to describe additional nonlinear responses to large ac voltages, such as Faradaic reactions, electro-osmotic instabilities, and induced-charge electrokinetic phenomena.

  12. Effect of the combined action of Faradaic currents and mobility differences in ac electro-osmosis

    NASA Astrophysics Data System (ADS)

    González, A.; Ramos, A.; García-Sánchez, P.; Castellanos, A.

    2010-01-01

    In this work, we extend previous analyses of ac electro-osmosis to account for the combined action of two experimentally relevant effects: (i) Faradaic currents from electrochemical reactions at the electrodes and (ii) differences in ion mobilities of the electrolyte. In previous works, the ac electro-osmotic motion has been analyzed theoretically under the assumption that only forces in the diffuse (Debye) layer are relevant. Here, we first show that if the ion mobilities of a 1-1 aqueous solution are different, the charged zone expands from the Debye layer to include the diffusion layer. We later include the Faradaic currents and, as an attempt to explore both factors simultaneously, we perform a thin-layer, low-frequency, linear analysis of the system. Finally, the model is applied to the case of an electrolyte actuated by a traveling-wave signal. A steady liquid motion in opposite direction to the applied signal is predicted for some ranges of the parameters. This could serve as a partial explanation for the observed flow reversal in some experiments.

  13. An electro-osmotic instability in biological cells

    NASA Astrophysics Data System (ADS)

    Leonetti, M.; Dubois-Violette, E.

    1997-01-01

    The development of ionic currents during the growth of biological cells contributes to the generation of spatial order. A new instability is proposed to describe such phenomenon. The mechanism triggering the instability is based on electro-osmosis flow which generates aggregation of channels or pumps. The onset of unstable modes and the dispersion relation are determined and a comparison with a biological cell is provided.

  14. Focusing and trapping of DNA molecules by head-on ac electrokinetic streaming through join asymmetric polarization

    PubMed Central

    Du, Jung-Rong; Wei, Hsien-Hung

    2010-01-01

    In this work, invoking join asymmetric ac polarization using double half-quadrupole electrodes in a symmetric arrangement, we demonstrate a head-on ac electro-osmotic streaming capable of focusing and trapping DNA molecules efficiently. This is manifested by the observation that picomolar DNA molecules can be trapped into a large crosslike spot with at least an order of magnitude concentration enhancement within just half a minute. We identify that the phenomenon is a combined result of the formation of two prefocused DNA jets flowing toward each other, dipole-induced attraction between focused DNA molecules, and dielectrophoretic trap on the spot. With an additional horizontal pumping, we observe that the trap can transform into a peculiar pitchfork streaming capable of continuous collection and long-distance transport of concentrated DNA molecules. We also show that the same electrode design can be used to direct assembly of submicrometer particles. This newly designed microfluidic platform not only has potentials in enhancing detection sensitivity and facilitating functional assembly for on-chip analysis but also provides an added advantage of transporting target molecules in a focused and continuous manner. PMID:20838480

  15. Electrodeposition of Au/Ag bimetallic dendrites assisted by Faradaic AC-electroosmosis flow

    SciTech Connect

    Ji, Jianlong; Li, Pengwei; Sang, Shengbo Zhang, Wendong Li, Gang; Hu, Jie; Zhou, Zhaoying Yang, Xing; Dong, Hualai

    2014-03-15

    Au/Ag bimetallic dendrites were synthesized successfully from the corresponding aqueous solution via the AC electrodeposition method. Both of the morphologies and compositions could be tuned by the electrolyte concentration and AC frequency. The prepared bimetallic dendrites were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS), transmission electron microscopy (TEM) and UV–vis spectroscopy. The underlying dendrite growth mechanism was then proposed in the context of the Directed Electrochemical Nanowires Assembly (DENA) models. Owing to the unscreened voltage dropping in the electrolyte bulk, electromigration dominates the species flux process, and cations tend to accumulate in areas with strong electric field intensity, such as electrode edges. Moreover, Faradaic AC-electro-osmosis (ACEO) flow could increase the effective diffusion layer thickness in these areas during the electrochemical reaction, and leads to dendrite growth. Further Micro-Raman observations illustrated that the Au/Ag bimetallic dendrites exhibited pronounced surface-enhanced Raman scattering (SERS) activity, using 4-mercaptopyridine (4-MP) as model molecules.

  16. Electrodeposition of Au/Ag bimetallic dendrites assisted by Faradaic AC-electroosmosis flow

    NASA Astrophysics Data System (ADS)

    Ji, Jianlong; Li, Pengwei; Sang, Shengbo; Zhang, Wendong; Zhou, Zhaoying; Yang, Xing; Dong, Hualai; Li, Gang; Hu, Jie

    2014-03-01

    Au/Ag bimetallic dendrites were synthesized successfully from the corresponding aqueous solution via the AC electrodeposition method. Both of the morphologies and compositions could be tuned by the electrolyte concentration and AC frequency. The prepared bimetallic dendrites were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS), transmission electron microscopy (TEM) and UV-vis spectroscopy. The underlying dendrite growth mechanism was then proposed in the context of the Directed Electrochemical Nanowires Assembly (DENA) models. Owing to the unscreened voltage dropping in the electrolyte bulk, electromigration dominates the species flux process, and cations tend to accumulate in areas with strong electric field intensity, such as electrode edges. Moreover, Faradaic AC-electro-osmosis (ACEO) flow could increase the effective diffusion layer thickness in these areas during the electrochemical reaction, and leads to dendrite growth. Further Micro-Raman observations illustrated that the Au/Ag bimetallic dendrites exhibited pronounced surface-enhanced Raman scattering (SERS) activity, using 4-mercaptopyridine (4-MP) as model molecules.

  17. Segregation Dynamics of Suspensions in Micro-Vortices

    NASA Astrophysics Data System (ADS)

    Hou, Diana

    2005-11-01

    Cylindrical vortices generated by AC electro-osmotic (AC-EO) flows on microelectrodes have been seen to attract and concentrate micro-particles. The particles are attracted to the vortex by dielectrophoretic (DEP) forces of the underlying micro-electrodes. However, shear-induced particle migration mechanisms can counter the DEP transport resulting in a filled vortex or an annulus. A dimensionless parameter χ relates the two opposing forces and defines the extent of particle invasion. The cylindrical vortices suffer a symmetry-breaking instability, break up into band structures along the axis and coalesce into more concentrated slugs. The instabilities are analyzed theoretically and attributed to longitudinal shear-induced migration due to dependence of the vortex shear rate on the local particle concentration. The concentrated funnel-shaped slugs exhibit fore-aft asymmetry along their axis and propagate in a specific direction at a constant speed. They are shown to be a solitary traveling wave solution of the Kuramoto-Sivashinsky equation.

  18. Capillary filling under electro-osmotic effects in the presence of electromagneto-hydrodynamic effects.

    PubMed

    Desai, Nikhil; Ghosh, Uddipta; Chakraborty, Suman

    2014-06-01

    We report various regimes of capillary filling dynamics under electromagneto-hydrodynamic interactions, in the presence of electrical double layer effects. Our chosen configuration considers an axial electric field and transverse magnetic field acting on an electrolyte. We demonstrate that for positive interfacial potential, the movement of the capillary front resembles capillary rise in a vertical channel under the action of gravity. We also evaluate the time taken by the capillary front to reach the final equilibrium position for positive interfacial potential and show that the presence of a transverse magnetic field delays the time of travel of the liquid front, thereby sustaining the capillary motion for a longer time. Our scaling estimates reveal that the initial linear regime starts, as well as ends, much earlier in the presence of electrical and magnetic body forces, as compared to the corresponding transients observed under pure surface tension driven flow. We further obtain a long time solution for the capillary imbibition for positive interfacial potential, and derive a scaling estimate of the capillary stopping time as a function of the applied magnetic field and an intrinsic length scale delineating electromechanical influences of the electrical double layer. Our findings are likely to offer alternative strategies of controlling dynamical features of capillary imbibition, by modulating the interplay between electromagnetic interactions, electrical double layer phenomena, and hydrodynamics over interfacial scales.

  19. The dominant role of surface conduction in electro-osmotic flows through periodically varying narrow channels

    NASA Astrophysics Data System (ADS)

    Ludar, Lotan; Yariv, Ehud

    2015-11-01

    As surface conduction has no effect on electro-osmosis in uniform channel flows, where the tangential Debye-layer currents are longitudinally uniform, it may appear as it would only result in a small modifying correction in lubrication analyses of slowly varying channels. This misconception is refuted here by analyzing flows through periodic channels of slowly varying but otherwise arbitrary geometry. Assuming that the channel width is still large compared with the Debye thickness we employ the simplest thin-double-layer model which incorporates surface conduction. We find that surface conduction affects the leading-order flow and the consequent net volumetric flux, introducing a nonlinear dependence upon the zeta potential. Remarkably, as the channel becomes more and more narrow, the scaled flux approaches a limit which is independent of the Dukhin number yet different from that calculated for zero Dukhin number.

  20. Electro-osmotic techniques for removal of chloride from concrete and for emplacement of concrete sealants

    NASA Astrophysics Data System (ADS)

    Jayaprakash, G. P.; Bukovatz, J. E.; Ramamurti, K.; Gilliland, W. J.

    1982-08-01

    Chloride ion from bridge deck concrete can be removed by application of a direct current potential between bridge reinforcing steel (-) and a copper screen (+) conductor on the bridge surface. Soaring prices of all types of energy would make removal of all chloride prohibitatively expensive. The importance of verification of all electrical connections prior to the treatment is emphasized by the demonstration of concrete cracking when the steel was made a positive instead of a negative electrode. Data on effectiveness of calcium nitrite corrosion inhibitor added to the concrete overlay placed on electrotreated concrete is not extensive due to accidental damage to the test slabs.

  1. Enzymatic digestion and liquid chromatography in micropillar reactors: hydrodynamic versus electro-osmotic flow

    NASA Astrophysics Data System (ADS)

    Sarrut, Nicolas; Bouffet, Stephanie; Mittler, Frederique; Constantin, Olivier; Combette, P.; Sudor, Jan; Ricoul, Florence; Vinet, Francoise; Garin, Jerome; Vauchier, Claude

    2005-01-01

    Enzymatic digestion and peptide separation are basic steps for preparation of protein samples prior to their analysis by mass spectrometry. Micro-pillar reactors for digestion and reverse phase liquid chromatography were designed and constructed using semiconductor technologies. The performances of the micro-machined reactors were evaluated: complete Cytochrome C digestion was achieved in 6 min for a concentration up to 25 pmolμl-1 and the separation micro-column was seen to exhibit separation capabilities and capacity close to those obtained with a commercial column. Furthermore, a comparative study between hydrodynamic and electroosmotic driven flows was performed for each peptide of a Cytochrome C digest. It was demonstrated that parasitic electrophoretic phenomena disturbed peptide mobility but not protein identification.

  2. ACS: ALMA Common Software

    NASA Astrophysics Data System (ADS)

    Chiozzi, Gianluca; Šekoranja, Matej

    2013-02-01

    ALMA Common Software (ACS) provides a software infrastructure common to all ALMA partners and consists of a documented collection of common patterns and components which implement those patterns. The heart of ACS is based on a distributed Component-Container model, with ACS Components implemented as CORBA objects in any of the supported programming languages. ACS provides common CORBA-based services such as logging, error and alarm management, configuration database and lifecycle management. Although designed for ALMA, ACS can and is being used in other control systems and distributed software projects, since it implements proven design patterns using state of the art, reliable technology. It also allows, through the use of well-known standard constructs and components, that other team members whom are not authors of ACS easily understand the architecture of software modules, making maintenance affordable even on a very large project.

  3. Microfabricated AC impedance sensor

    DOEpatents

    Krulevitch, Peter; Ackler, Harold D.; Becker, Frederick; Boser, Bernhard E.; Eldredge, Adam B.; Fuller, Christopher K.; Gascoyne, Peter R. C.; Hamilton, Julie K.; Swierkowski, Stefan P.; Wang, Xiao-Bo

    2002-01-01

    A microfabricated instrument for detecting and identifying cells and other particles based on alternating current (AC) impedance measurements. The microfabricated AC impedance sensor includes two critical elements: 1) a microfluidic chip, preferably of glass substrates, having at least one microchannel therein and with electrodes patterned on both substrates, and 2) electrical circuits that connect to the electrodes on the microfluidic chip and detect signals associated with particles traveling down the microchannels. These circuits enable multiple AC impedance measurements of individual particles at high throughput rates with sufficient resolution to identify different particle and cell types as appropriate for environmental detection and clinical diagnostic applications.

  4. AC magnetohydrodynamic microfluidic switch

    SciTech Connect

    Lemoff, A V; Lee, A P

    2000-03-02

    A microfluidic switch has been demonstrated using an AC Magnetohydrodynamic (MHD) pumping mechanism in which the Lorentz force is used to pump an electrolytic solution. By integrating two AC MHD pumps into different arms of a Y-shaped fluidic circuit, flow can be switched between the two arms. This type of switch can be used to produce complex fluidic routing, which may have multiple applications in {micro}TAS.

  5. Isolation of sequences flanking Ac insertion sites by Ac casting.

    PubMed

    Wang, Dafang; Peterson, Thomas

    2013-01-01

    Localizing Ac insertions is a fundamental task in studying Ac-induced mutation and chromosomal rearrangements involving Ac elements. Researchers may sometimes be faced with the situation in which the sequence flanking one side of an Ac/Ds element is known, but the other flank is unknown. Or, a researcher may have a small sequence surrounding the Ac/Ds insertion site and needs to obtain additional flanking genomic sequences. One way to rapidly clone unknown Ac/Ds flanking sequences is via a PCR-based method termed Ac casting. This approach utilizes the somatic transposition activity of Ac during plant development, and provides an efficient means for short-range genome walking. Here we describe the principle of Ac casting, and show how it can be applied to isolate Ac macrotransposon insertion sites.

  6. Tevatron AC dipole system

    SciTech Connect

    Miyamoto, R.; Kopp, S.E.; Jansson, A.; Syphers, M.J.; /Fermilab

    2007-06-01

    The AC dipole is an oscillating dipole magnet which can induce large amplitude oscillations without the emittance growth and decoherence. These properties make it a good tool to measure optics of a hadron synchrotron. The vertical AC dipole for the Tevatron is powered by an inexpensive high power audio amplifier since its operating frequency is approximately 20 kHz. The magnet is incorporated into a parallel resonant system to maximize the current. The use of a vertical pinger magnet which has been installed in the Tevatron made the cost relatively inexpensive. Recently, the initial system was upgraded with a more powerful amplifier and oscillation amplitudes up to 2-3{sigma} were achieved with the 980 GeV proton beam. This paper discusses details of the Tevatron AC dipole system and also shows its test results.

  7. AC-3 audio coder

    NASA Astrophysics Data System (ADS)

    Todd, Craig

    1995-12-01

    AC-3 is a system for coding up to 5.1 channels of audio into a low bit-rate data stream. High quality may be obtained with compression ratios approaching 12-1 for multichannel audio programs. The high compression ratio is achieved by methods which do not increase decoder memory, and thus cost. The methods employed include: the transmission of a high frequency resolution spectral envelope; and a novel forward/backward adaptive bit allocation algorithm. In order to satisfy practical requirements of an emissions coder, the AC-3 syntax includes a number of features useful to broadcasters and consumers. These features include: loudness uniformity between programs; dynamic range control; and broadcaster control of downmix coefficients. The AC-3 coder has been formally selected for inclusion of the U.S. HDTV broadcast standard, and has been informally selected for several additional applications.

  8. ac bidirectional motor controller

    NASA Technical Reports Server (NTRS)

    Schreiner, K.

    1988-01-01

    Test data are presented and the design of a high-efficiency motor/generator controller at NASA-Lewis for use with the Space Station power system testbed is described. The bidirectional motor driver is a 20 kHz to variable frequency three-phase ac converter that operates from the high-frequency ac bus being designed for the Space Station. A zero-voltage-switching pulse-density-modulation technique is used in the converter to shape the low-frequency output waveform.

  9. AC/RF Superconductivity

    SciTech Connect

    Ciovati, Gianluigi

    2015-02-01

    This contribution provides a brief introduction to AC/RF superconductivity, with an emphasis on application to accelerators. The topics covered include the surface impedance of normal conductors and superconductors, the residual resistance, the field dependence of the surface resistance, and the superheating field.

  10. Analysis of induced-charge electro-osmotic flow in a microchannel embedded with polarizable dielectric blocks.

    PubMed

    Zhao, Cunlu; Yang, Chun

    2009-10-01

    Within the frame work of classic electromagnetic theory, a general electrical boundary condition describing the induced-charge electrokinetic phenomena at the liquid-dielectric interface is proposed in the present study. Two well-known limiting cases, i.e., perfectly insulating and perfectly polarizable wall boundary conditions, can be recovered from the present electrical boundary condition. By utilizing the proposed boundary condition, the induced-charge electro-osmosis (ICEO) flow in an infinitely long microchannel patterned with two symmetric polarizable dielectric blocks is investigated analytically. Fourier transform method is invoked to solve a biharmonic equation, which governs the (ICEO) flow field described by the stream function. Dimensionless parameters are introduced, and their effects on flow characteristics are analyzed. It is found that an increase in polarizability of the dielectric block enhances the slip velocity on its surface and thus induces a pair of counter-rotating vortices. Also, increasing the natural zeta potential on the upstream and downstream of the insulating microchannel walls leads to extinction of the vortex near the upstream insulating microchannel and suppression of the vortex near the downstream insulating microchannel.

  11. Molecular Dynamics of Membrane-Spanning DNA Channels: Conductance Mechanism, Electro-Osmotic Transport, and Mechanical Gating.

    PubMed

    Yoo, Jejoong; Aksimentiev, Aleksei

    2015-12-01

    DNA self-assembly has emerged as a new paradigm for design of biomimetic membrane channels. Several experimental groups have already demonstrated assembly and insertion of DNA channels into lipid bilayer membranes; however, the structure of the channels and their conductance mechanism have remained undetermined. Here, we report the results of molecular dynamics simulations that characterized the biophysical properties of the DNA membrane channels with atomic precision. We show that, while overall remaining stable, the local structure of the channels undergoes considerable fluctuations, departing from the idealized design. The transmembrane ionic current flows both through the central pore of the channel as well as along the DNA walls and through the gaps in the DNA structure. Surprisingly, we find that the conductance of DNA channels depend on the membrane tension, making them potentially suitable for force-sensing applications. Finally, we show that electro-osmosis governs the transport of druglike molecules through the DNA channels. PMID:26551518

  12. Dynamical trapping of colloids at the stagnation points of electro-osmotic vortices of the second kind

    NASA Astrophysics Data System (ADS)

    Green, Yoav; Yossifon, Gilad

    2013-03-01

    By applying a stepwise overlimiting voltage to a nanoslot system in equilibrium, it is possible to follow the time evolution of the electroconvective instability vortex array via the depletion dynamics or, alternatively, by following dielectrophoretically trapped particles at the stagnation points of each of the hydrodynamic vortex pairs. Particles are advected to the stagnation point by the hydrodynamics, where they are trapped by a short-range dielectrophoretic force. It is experimentally confirmed that the wavelength selection process occurs at the diffusive time scale and that the wavelength selection mechanism, started by the Rubinstein and Zaltzman electroconvective instability is eventually determined by the system lateral geometry and dictated by Dukhin's electro-osmosis of the second kind. The steady-state case was numerically studied by solving the fully coupled electroconvective problem, confirming that the vortex stagnation point is indeed of a converging type. The particle's planar (two-dimensional) equations of motion are solved after adding a dielectrophoretic force that accounts for quasi-three-dimensional effects. It is shown that this force can account for trapping at the nanoslot interface.

  13. Spatially uniform microflows induced by thermoviscous expansion along a traveling temperature wave: Analogies with electro-osmotic transport

    NASA Astrophysics Data System (ADS)

    Pal, Debashis; Chakraborty, Suman

    2012-07-01

    We discover that thermoviscous expansion along a traveling wave in a microfluidic channel may be capable of generating a spatially uniform flow profile in a time-averaged sense. We further delineate that the resultant complex flow characteristics, realized by virtue of an intricate interplay between thermal compression-expansion waves and temperature-dependent viscosity variations and controlled by an external heating, may be remarkably characterized by a unique thermal penetration depth scale (analogous to Debye length in electro-osmosis) and a velocity scale (analogous to the Helmholtz Smulochowski velocity in electro-osmosis) that in turn depends on the considerations of “thin” and “thick” microchannel limits, as dictated by the thermal penetration depth as compared to the lateral extent of the microfluidic channel. We show that, when the thermal penetration depth is small as compared to the channel height, a uniform velocity profile is generated in the channel in a time-averaged sense. The velocity scale characterizing this uniform flow may be represented by a function of the thermal diffusivity, volumetric expansion coefficient and thermal viscosity coefficient of the fluid, characteristic amplitude and speed of the thermal wave, as well as the channel height. Results from the present study are expected to provide valuable insights towards arresting hydrodynamic dispersion in microchannels by nonelectrochemical means, following a pH-independent route.

  14. Concentration Polarization and Nonequilibrium Electro-osmotic Instability at an Ion-Selective Surface Admitting Normal Flow

    NASA Astrophysics Data System (ADS)

    Khair, Aditya

    2011-11-01

    We revisit and build upon on the prototypical problem of ion transport across a flat ideal ion-selective surface. Specifically, we examine the influence of imposed fluid flows on concentration polarization (CP) and electrokinetic instability at over-limiting currents. We consider an ion-selective surface, or membrane, that admits a uniform flow across itself. The membrane contacts an electrolyte, whose concentration is uniform in a well-mixed region at a prescribed distance from the membrane. A voltage across the system drives an ionic current, leading to CP in the ``unstirred layer'' between the membrane and well-mixed bulk. The CP reflects a balance between advection of ions with the ``normal flow'' and diffusion. A Peclet number, Pe, parameterizes their relative importance; note, Pe is signed, as the flow can be toward or away from the membrane. An asymptotic analysis for thin Debye layers reveals a nonlinear CP profile, in contrast to the familiar linear profile at Pe=0. Next, we consider over-limiting currents, wherein a non-equilibrium space-charge layer emerges near the membrane surface. Finally, we examine the instability of the quiescent concentration polarization due to second-kind electro-osmosis in the space-charge layer. A stability analysis shows that the imposed normal flow can enhance or retard the instability, depending on its direction.

  15. Field Measurements of Electro-osmotic Transport of Ground Water Contaminants in a Lithologically Heterogeneous Alluvial-Fan Setting

    SciTech Connect

    McNab,W; Karachewski,J; Weismann,G

    2001-07-31

    Remediation of contaminated ground water by pump-and-treat approaches is often problematic because the heterogeneous distributions of lithologies, and hence hydraulic conductivities, characterizing many aquifers result in complex flow paths. Consequently, contaminants are removed readily from the most permeable regions of the subsurface but the less permeable sediments, rich in clay and silt, remain largely undisturbed. These continue to act as diffusion-limited sources for further contamination of the permeable sediments. Under certain circumstances, specialized technologies, such as electrokinetic approaches, may be useful for enhancing the removal of ground water from low-permeability sediments. These circumstances generally include high contaminant concentrations--hence posing a chronic source threat--and a relatively small area requiring treatment. At Lawrence Livermore National Laboratory (LLNL) in Livermore, California, electro-osmosis (EO) is being evaluated as a means for extracting ground water containing trichloroethylene (TCE) and other chlorinated hydrocarbons from fine-grained sediments in a plume source area.

  16. AC power systems handbook

    SciTech Connect

    Whitaker, J.

    1991-01-01

    Transient disturbances are what headaches are made of. Whatever you call them-spikes, surges, are power bumps-they can take your equipment down and leave you with a complicated and expensive repair job. Protection against transient disturbances is a science that demands attention to detail. This book explains how the power distribution system works, what can go wrong with it, and how to protect a facility against abnormalities. system grounding and shielding are covered in detail. Each major method of transient protection is analyzed and its relative merits discussed. The book provides a complete look at the critical elements of the ac power system. Provides a complete look at the ac power system from generation to consumption. Discusses the mechanisms that produce transient disturbances and how to protect against them. Presents diagrams to facilitate system design. Covers new areas, such as the extent of the transient disturbance problem, transient protection options, and stand-by power systems.

  17. Increased Ac excision (iae): Arabidopsis thaliana mutations affecting Ac transposition.

    PubMed

    Jarvis, P; Belzile, F; Page, T; Dean, C

    1997-05-01

    The maize transposable element Ac is highly active in the heterologous hosts tobacco and tomato, but shows very much reduced levels of activity in Arabidopsis. A mutagenesis experiment was undertaken with the aim of identifying Arabidopsis host factors responsible for the observed low levels of Ac activity. Seed from a line carrying a single copy of the Ac element inserted into the streptomycin phosphotransferase (SPT) reporter fusion, and which displayed typically low levels of Ac activity, were mutagenized using gamma rays. Nineteen mutants displaying high levels of somatic Ac activity, as judged by their highly variegated phenotypes, were isolated after screening the M2 generation on streptomycin-containing medium. The mutations fall into two complementation groups, iae1 and iae2, are unlinked to the SPT::Ac locus and segregate in a Mendelian fashion. The iae1 mutation is recessive and the iae2 mutation is semi-dominant. The iae1 and iae2 mutants show 550- and 70-fold increases, respectively, in the average number of Ac excision sectors per cotyledon. The IAE1 locus maps to chromosome 2, whereas the SPT::Ac reporter maps to chromosome 3. A molecular study of Ac activity in the iae1 mutant confirmed the very high levels of Ac excision predicted using the phenotypic assay, but revealed only low levels of Ac re-insertion. Analyses of germinal transposition in the iae1 mutant demonstrated an average germinal excision frequency of 3% and a frequency of independent Ac re-insertions following germinal excision of 22%. The iae mutants represents a possible means of improving the efficiency of Ac/Ds transposon tagging systems in Arabidopsis, and will enable the dissection of host involvement in Ac transposition and the mechanisms employed for controlling transposable element activity.

  18. AC resistance measuring instrument

    DOEpatents

    Hof, P.J.

    1983-10-04

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument. 8 figs.

  19. AC Resistance measuring instrument

    DOEpatents

    Hof, Peter J.

    1983-01-01

    An auto-ranging AC resistance measuring instrument for remote measurement of the resistance of an electrical device or circuit connected to the instrument includes a signal generator which generates an AC excitation signal for application to a load, including the device and the transmission line, a monitoring circuit which provides a digitally encoded signal representing the voltage across the load, and a microprocessor which operates under program control to provide an auto-ranging function by which range resistance is connected in circuit with the load to limit the load voltage to an acceptable range for the instrument, and an auto-compensating function by which compensating capacitance is connected in shunt with the range resistance to compensate for the effects of line capacitance. After the auto-ranging and auto-compensation functions are complete, the microprocessor calculates the resistance of the load from the selected range resistance, the excitation signal, and the load voltage signal, and displays of the measured resistance on a digital display of the instrument.

  20. Identification of /sup 233/Ac

    SciTech Connect

    Chu, Y.Y.; Zhou, M.L.

    1983-09-01

    We report in this paper identification of the new isotope /sup 233/Ac. Uranium targets were irradiated with 28 GeV protons; after rapid retrieval of the target and separation of actinium from thorium, /sup 233/Ac was allowed to decay into the known /sup 233/Th daughter. Exhaustive chemical purification was employed to permit the identification of /sup 233/Th via its characteristic ..gamma.. radiations. The half-life derived for /sup 233/Ac from several experiments is 2.3 +- 0.3 min. The production cross section for /sup 233/Ac is 100 ..mu..b.

  1. AC and DC power transmission

    SciTech Connect

    Not Available

    1985-01-01

    The technical and economic assessment of AC and DC transmission systems; long distance transmission, cable transmission, system inter-connection, voltage support, reactive compensation, stabilisation of systems; parallel operation of DC links with AC systems; comparison between alternatives for particular schemes. Design and application equipment: design, testing and application of equipment for HVDC, series and shunt static compensated AC schemes, including associated controls. Installations: overall design of stations and conductor arrangements for HVDC, series and shunt static AC schemes including insulation co-ordination. System analysis and modelling.

  2. Digital ac monitor

    DOEpatents

    Hart, G.W.; Kern, E.C. Jr.

    1987-06-09

    An apparatus and method is provided for monitoring a plurality of analog ac circuits by sampling the voltage and current waveform in each circuit at predetermined intervals, converting the analog current and voltage samples to digital format, storing the digitized current and voltage samples and using the stored digitized current and voltage samples to calculate a variety of electrical parameters; some of which are derived from the stored samples. The non-derived quantities are repeatedly calculated and stored over many separate cycles then averaged. The derived quantities are then calculated at the end of an averaging period. This produces a more accurate reading, especially when averaging over a period in which the power varies over a wide dynamic range. Frequency is measured by timing three cycles of the voltage waveform using the upward zero crossover point as a starting point for a digital timer. 24 figs.

  3. Digital ac monitor

    DOEpatents

    Hart, George W.; Kern, Jr., Edward C.

    1987-06-09

    An apparatus and method is provided for monitoring a plurality of analog ac circuits by sampling the voltage and current waveform in each circuit at predetermined intervals, converting the analog current and voltage samples to digital format, storing the digitized current and voltage samples and using the stored digitized current and voltage samples to calculate a variety of electrical parameters; some of which are derived from the stored samples. The non-derived quantities are repeatedly calculated and stored over many separate cycles then averaged. The derived quantities are then calculated at the end of an averaging period. This produces a more accurate reading, especially when averaging over a period in which the power varies over a wide dynamic range. Frequency is measured by timing three cycles of the voltage waveform using the upward zero crossover point as a starting point for a digital timer.

  4. Cooling Floor AC Systems

    NASA Astrophysics Data System (ADS)

    Jun, Lu; Hao, Ding; Hong, Zhang; Ce, Gao Dian

    The present HVAC equipments for the residential buildings in the Hot-summer-and-Cold-winter climate region are still at a high energy consuming level. So that the high efficiency HVAC system is an urgently need for achieving the preset government energy saving goal. With its advantage of highly sanitary, highly comfortable and uniform of temperature field, the hot-water resource floor radiation heating system has been widely accepted. This paper has put forward a new way in air-conditioning, which combines the fresh-air supply unit and such floor radiation system for the dehumidification and cooling in summer or heating in winter. By analyze its advantages and limitations, we found that this so called Cooling/ Heating Floor AC System can improve the IAQ of residential building while keep high efficiency quality. We also recommend a methodology for the HVAC system designing, which will ensure the reduction of energy cost of users.

  5. Operation Method for AC Motor Control during Power Interruption in Direct AC/AC Converter System

    NASA Astrophysics Data System (ADS)

    Shizu, Keiichiro; Azuma, Satoshi

    Direct AC/AC converters have been studied due to their potential use in power converters with no DC-link capacitor, which can contribute to the miniaturization of power converters. However, the absence of a DC-link capacitor makes it difficult to control the AC motor during power interruption. First, this paper proposes a system that realizes AC motor control during power interruption by utilizing a clamp capacitor. In general, direct AC/AC converters have a clamp circuit consisting of a rectifier diode(s) and a clamp capacitor in order to avoid over-voltages. In the proposed system, there is an additional semiconductor switch reverse-parallel to the rectifier diode(s), and the clamp capacitor voltage can be utilized for AC motor control by turning on the additional switch. Second, this paper discusses an operation method for AC motor control and clamp capacitor voltage control during power interruption. In the proposed method “DC-link voltage control”, the kinetic energy in the AC motor is transformed into electrical energy and stored in the clamp capacitor; the clamp capacitor is therefore charged and the capacitor voltage is controlled to remain constant at an instruction value. Third, this paper discusses a switching operation during power interruption. A dead-time is introduced between the operation of turning off all switches on the rectifier side and the operation of turning on the additional switch, which prevents the occurrence of a short circuit between the interrupted power source and the clamp capacitor. Finally, experimental results are presented. During power interruptions, an output current was continuously obtained and the clamp capacitor voltage was maintained to be equal to the instruction value of the capacitor voltage. These results indicate that both AC motor control and capacitor voltage control were successfully achieved by using the proposed system.

  6. ACS CCD Stability Monitor

    NASA Astrophysics Data System (ADS)

    Grogin, Norman

    2012-10-01

    A moderately crowded stellar field in the cluster 47 Tuc {6 arcmin West of the cluster core} is observed every four months with the WFC. The first visit exercises the full suite of broad and narrow band imaging filters and sub-array modes; following visits observe with only the six most popular Cycle 18 filters in full-frame mode. The positions and magnitudes of objects will be used to monitor local and large scale variations in the plate scale and the sensitivity of the detectors and to derive an independent measure of the detector CTE. One exposure in each sub-array mode with the WFC will allow us to verify that photometry obtained in full-frame and in sub-array modes are repeatable to better than 1%. This test is important for the ACS Photometric Cross-Calibration program, which uses sub-array exposures. This program may receive additional orbits to investigate ORIENT-dependent geometric distortion, which motivates the ORIENT and BETWEEN requirement on the first visit.

  7. AC photovoltaic module magnetic fields

    SciTech Connect

    Jennings, C.; Chang, G.J.; Reyes, A.B.; Whitaker, C.M.

    1997-12-31

    Implementation of alternating current (AC) photovoltaic (PV) modules, particularly for distributed applications such as PV rooftops and facades, may be slowed by public concern about electric and magnetic fields (EMF). This paper documents magnetic field measurements on an AC PV module, complementing EMF research on direct-current PV modules conducted by PG and E in 1993. Although not comprehensive, the PV EMF data indicate that 60 Hz magnetic fields (the EMF type of greatest public concern) from PV modules are comparable to, or significantly less than, those from household appliances. Given the present EMF research knowledge, AC PV module EMF may not merit considerable concern.

  8. The ac53, ac78, ac101, and ac103 Genes Are Newly Discovered Core Genes in the Family Baculoviridae

    PubMed Central

    Garavaglia, Matías Javier; Miele, Solange Ana Belén; Iserte, Javier Alonso; Belaich, Mariano Nicolás

    2012-01-01

    The family Baculoviridae is a large group of insect viruses containing circular double-stranded DNA genomes of 80 to 180 kbp, which have broad biotechnological applications. A key feature to understand and manipulate them is the recognition of orthology. However, the differences in gene contents and evolutionary distances among the known members of this family make it difficult to assign sequence orthology. In this study, the genome sequences of 58 baculoviruses were analyzed, with the aim to detect previously undescribed core genes because of their remote homology. A routine based on Multi PSI-Blast/tBlastN and Multi HaMStR allowed us to detect 31 of 33 accepted core genes and 4 orthologous sequences in the Baculoviridae which were not described previously. Our results show that the ac53, ac78, ac101 (p40), and ac103 (p48) genes have orthologs in all genomes and should be considered core genes. Accordingly, there are 37 orthologous genes in the family Baculoviridae. PMID:22933288

  9. Semiconductor ac static power switch

    NASA Technical Reports Server (NTRS)

    Vrancik, J.

    1968-01-01

    Semiconductor ac static power switch has long life and high reliability, contains no moving parts, and operates satisfactorily in severe environments, including high vibration and shock conditions. Due to their resistance to shock and vibration, static switches are used where accidental switching caused by mechanical vibration or shock cannot be tolerated.

  10. ACS Expands Role In High School Chemistry.

    ERIC Educational Resources Information Center

    Chemical and Engineering News, 1979

    1979-01-01

    Describes some of the services and programs of special interests to high school chemistry teachers that are being provided by ACS, and meant to make ACS membership more attractive to the teachers. (GA)

  11. Simultaneous distribution of AC and DC power

    DOEpatents

    Polese, Luigi Gentile

    2015-09-15

    A system and method for the transport and distribution of both AC (alternating current) power and DC (direct current) power over wiring infrastructure normally used for distributing AC power only, for example, residential and/or commercial buildings' electrical wires is disclosed and taught. The system and method permits the combining of AC and DC power sources and the simultaneous distribution of the resulting power over the same wiring. At the utilization site a complementary device permits the separation of the DC power from the AC power and their reconstruction, for use in conventional AC-only and DC-only devices.

  12. Small-Signal ac Analysis

    NASA Technical Reports Server (NTRS)

    Jagielski, James M.; Chen, Jess

    1987-01-01

    Program simulates power circuits and systems. Small Signal A.C. Analysis program (SSAC) valuable tool for design and analysis of electrical-power-system circuits. By combining "black box" power-system components operating in specified manner, user characterizes system modeled. Menu-driven program proved simple and cost effective in development and modification of arbitrary power-system configurations. Package includes sample data from Dynamic Explorer satellite family. Results compared favorable to calculations from such general circuit-analysis programs as SPICE. Written in FORTRAN 77.

  13. Effect of the magnetic material on AC losses in HTS conductors in AC magnetic field carrying AC transport current

    NASA Astrophysics Data System (ADS)

    Wan, Xing-Xing; Huang, Chen-Guang; Yong, Hua-Dong; Zhou, You-He

    2015-11-01

    This paper presents an investigation on the AC losses in several typical superconducting composite conductors using the H-formulation model. A single superconducting strip with ferromagnetic substrate or cores and a stack of coated conductors with ferromagnetic substrates are studied. We consider all the coated conductors carrying AC transport currents and simultaneously exposed to perpendicular AC magnetic fields. The influences of the amplitude, frequency, phase difference and ferromagnetic materials on the AC losses are investigated. The results show that the magnetization losses of single strip and stacked strips have similar characteristics. The ferromagnetic substrate can increase the magnetization loss at low magnetic field, and decrease the loss at high magnetic field. The ferromagnetic substrate can obviously increase the transport loss in stacked strips. The trends of total AC losses of single strip and stacked strips are similar when they are carrying current or exposed to a perpendicular magnetic field. The effect of the frequency on the total AC losses of single strip is related to the amplitude of magnetic field. The AC losses decrease with increasing frequency in low magnetic field region while increase in high magnetic field region. As the phase difference changes, there is a periodic variation for the AC losses. Moreover, when the strip is under only the transport current and magnetic field, the ferromagnetic cores will increase the AC losses for large transport current or field.

  14. ac electroosmosis in rectangular microchannels.

    PubMed

    Campisi, Michele; Accoto, Dino; Dario, Paolo

    2005-11-22

    Motivated by the growing interest in ac electroosmosis as a reliable no moving parts strategy to control fluid motion in microfluidic devices for biomedical applications, such as lab-on-a-chip, we study transient and steady-state electrokinetic phenomena (electroosmosis and streaming currents) in infinitely extended rectangular charged microchannels. With the aid of Fourier series and Laplace transforms we provide a general formal solution of the problem, which is used to study the time-dependent response to sudden ac applied voltage differences in case of finite electric double layer. The Debye-Huckel approximation has been adopted to allow for an algebraic solution of the Poisson-Boltzmann problem in Fourier space. We obtain the expressions of flow velocity profiles, flow rates, streaming currents, as well as expressions of the complex hydraulic and electrokinetic conductances. We analyze in detail the dependence of the electrokinetic conductance on the extension of linear dimensions relative to the Debye length, with an eye on finite electric double layer effects. PMID:16351310

  15. RHIC spin flipper AC dipole controller

    SciTech Connect

    Oddo, P.; Bai, M.; Dawson, C.; Gassner, D.; Harvey, M.; Hayes, T.; Mernick, K.; Minty, M.; Roser, T.; Severino, F.; Smith, K.

    2011-03-28

    The RHIC Spin Flipper's five high-Q AC dipoles which are driven by a swept frequency waveform require precise control of phase and amplitude during the sweep. This control is achieved using FPGA based feedback controllers. Multiple feedback loops are used to and dynamically tune the magnets. The current implementation and results will be presented. Work on a new spin flipper for RHIC (Relativistic Heavy Ion Collider) incorporating multiple dynamically tuned high-Q AC-dipoles has been developed for RHIC spin-physics experiments. A spin flipper is needed to cancel systematic errors by reversing the spin direction of the two colliding beams multiple times during a store. The spin flipper system consists of four DC-dipole magnets (spin rotators) and five AC-dipole magnets. Multiple AC-dipoles are needed to localize the driven coherent betatron oscillation inside the spin flipper. Operationally the AC-dipoles form two swept frequency bumps that minimize the effect of the AC-dipole dipoles outside of the spin flipper. Both AC bumps operate at the same frequency, but are phase shifted from each other. The AC-dipoles therefore require precise control over amplitude and phase making the implementation of the AC-dipole controller the central challenge.

  16. Three phase AC motor controller

    DOEpatents

    Vuckovich, Michael; Wright, Maynard K.; Burkett, John P.

    1984-03-20

    A motor controller for a three phase AC motor (10) which is adapted to operate bidirectionally from signals received either from a computer (30) or a manual control (32). The controller is comprised of digital logic circuit means which implement a forward and reverse command signal channel (27, 29) for the application of power through the forward and reverse power switching relays (16, 18, 20, 22). The digital logic elements are cross coupled to prevent activation of both channels simultaneously and each includes a plugging circuit (65, 67) for stopping the motor upon the removal of control signal applied to one of the two channels (27, 29) for a direction of rotation desired. Each plugging circuit (65, 67) includes a one-shot pulse signal generator (88, 102) which outputs a single pulse signal of predetermined pulsewidth which is adapted to inhibit further operation of the application of power in the channel which is being activated and to apply a reversal command signal to the other channel which provides a reversed phase application of power to the motor for a period defined by the pulse-width output of the one-shot signal generator to plug the motor (10) which will then be inoperative until another rotational command signal is applied to either of the two channels.

  17. Superconductor coil geometry and ac losses

    NASA Technical Reports Server (NTRS)

    Pierce, T. V., Jr.; Zapata, R. N.

    1976-01-01

    An empirical relation is presented which allows simple computation of volume-averaged winding fields from central fields for coils of small rectangular cross sections. This relation suggests that, in certain applications, ac-loss minimization can be accomplished by use of low winding densities, provided that hysteresis losses are independent of winding density. The ac-loss measurements on coils wound of twisted multifilamentary composite superconductors show no significant dependence on ac losses on winding density, thus permitting the use of winding density as an independent design parameter in loss minimization.

  18. High School Teachers Win ACS Prizes

    NASA Astrophysics Data System (ADS)

    Editorial Staff, Jce

    2009-07-01

    William E. Snyder is the 2009 winner of the ACS Division of Chemical Education Central Region Award for Excellence in High School Teaching; Sally Mitchell is the winner of the 2009 James Bryant Conant Award in High School Chemistry Teaching.

  19. Tevatron optics measurements using an AC dipole

    SciTech Connect

    Miyamoto, R.; Kopp, S.E.; Jansson, A.; Syphers, M.J.; /Fermilab

    2007-06-01

    The AC dipole is a device to study beam optics of hadron synchrotrons. It can produce sustained large amplitude oscillations with virtually no emittance growth. A vertical AC dipole for the Tevatron is recently implemented and a maximum oscillation amplitude of 2{sigma} (4{sigma}) at 980 GeV (150 GeV) is achieved [1]. When such large oscillations are measured with the BPM system of the Tevatron (20 {micro}m resolution), not only linear but even nonlinear optics can be directly measured. This paper shows how to measure {beta} function using an AC dipole and the result is compared to the other measurement. The paper also shows a test to detect optics changes when small changes are made in the Tevatron. Since an AC dipole is nondestructive, it allows frequent measurements of the optics which is necessary for such an test.

  20. The AC-120: The advanced commercial transport

    NASA Technical Reports Server (NTRS)

    Duran, David; Griffin, Ernest; Mendoza, Saul; Nguyen, Son; Pickett, Tim; Noernberg, Clemm

    1993-01-01

    The main objective of this design was to fulfill a need for a new airplane to replace the aging 100 to 150 passenger, 1500 nautical mile range aircraft such as the Douglas DC9 and Boeing 737-100 airplanes. After researching the future aircraft market, conducting extensive trade studies, and analysis on different configurations, the AC-120 Advanced Commercial Transport final design was achieved. The AC-120's main design features include the incorporation of a three lifting surface configuration which is powered by two turboprop engines. The AC-120 is an economically sensitive aircraft which meets the new FM Stage Three noise requirements, and has lower NO(x) emissions than current turbofan powered airplanes. The AC-120 also improves on its contemporaries in passenger comfort, manufacturing, and operating cost.

  1. 78 FR 39345 - ACS Wireless, Inc.; Notice of Application

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-01

    ... COMMISSION ACS Wireless, Inc.; Notice of Application AGENCY: Securities and Exchange Commission (``Commission...''). Summary of Application: ACS Wireless, Inc. (``ACS Wireless'') seeks an order under section 3(b)(2) of the..., owning, holding or trading in securities. ACS Wireless is primarily engaged in providing...

  2. 21 CFR 888.1240 - AC-powered dynamometer.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered dynamometer. 888.1240 Section 888.1240...) MEDICAL DEVICES ORTHOPEDIC DEVICES Diagnostic Devices § 888.1240 AC-powered dynamometer. (a) Identification. An AC-powered dynamometer is an AC-powered device intended for medical purposes to...

  3. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  4. 21 CFR 886.1630 - AC-powered photostimulator.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered photostimulator. 886.1630 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1630 AC-powered photostimulator. (a) Identification. An AC-powered photostimulator is an AC-powered device intended to provide light stimulus...

  5. 21 CFR 886.1850 - AC-powered slitlamp biomicroscope.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered slitlamp biomicroscope. 886.1850... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1850 AC-powered slitlamp biomicroscope. (a) Identification. An AC-powered slitlamp biomicroscope is an AC-powered device that is...

  6. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  7. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  8. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  9. 21 CFR 886.4440 - AC-powered magnet.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false AC-powered magnet. 886.4440 Section 886.4440 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4440 AC-powered magnet. (a) Identification. An AC-powered magnet is an AC-powered device that generates a magnetic field intended to find and...

  10. AC Electrokinetics of Physiological Fluids for Biomedical Applications.

    PubMed

    Lu, Yi; Liu, Tingting; Lamanda, Ariana C; Sin, Mandy L Y; Gau, Vincent; Liao, Joseph C; Wong, Pak Kin

    2015-12-01

    Alternating current (AC) electrokinetics is a collection of processes for manipulating bulk fluid mass and embedded objects with AC electric fields. The ability of AC electrokinetics to implement the major microfluidic operations, such as pumping, mixing, concentration, and separation, makes it possible to develop integrated systems for clinical diagnostics in nontraditional health care settings. The high conductivity of physiological fluids presents new challenges and opportunities for AC electrokinetics-based diagnostic systems. In this review, AC electrokinetic phenomena in conductive physiological fluids are described followed by a review of the basic microfluidic operations and the recent biomedical applications of AC electrokinetics. The future prospects of AC electrokinetics for clinical diagnostics are presented.

  11. Deletion of AcMNPV ac146 eliminates the production of budded virus.

    PubMed

    Dickison, Virginia L; Willis, Leslie G; Sokal, Nadia R; Theilmann, David A

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac146 is a highly conserved gene in the Alpha- and Betabaculovirus genera that has an unknown function. Northern blot analysis and transcript mapping showed that ac146 is transcribed at late times post infection as a 1.2 kb mRNA. To determine the role of ac146 in the baculovirus life cycle ac146 knock out viruses were constructed. Transfection and plaque assays showed that all the ac146 deletions produced a single cell phenotype indicating that no infectious budded virus (BV) was produced, however occlusion bodies were formed. The lack of BV production was confirmed by viral titration utilizing both qPCR and TCID₅₀. Analysis of BV and occlusion derived virus (ODV) revealed that AC146 is associated with both forms of the virus and is modified specifically in ODV. This study therefore demonstrates that AC146 is a late virion associated protein and is essential for the viral life cycle.

  12. Cyclotron and linac production of Ac-225.

    PubMed

    Melville, Graeme; Allen, Barry J

    2009-04-01

    Radium needles that were once implanted into tumours as a cancer treatment are now obsolete and constitute a radioactive waste problem, as their half-life is 1600 years. The reduction of radium by photonuclear transmutation by bombarding Ra-226 with high-energy photons from a medical linear accelerator (linac) has been investigated. A linac dose of 2800 Gy produced about 2.4 MBq (64 microCi) of Ra-225, which decays to Ac-225 and can then be used for 'Targeted Alpha Therapy' (TAT) of cancer. This result, while consistent with theoretical calculations, is far too low to be of practical use unless much larger quantities of radium are irradiated. The increasing application of Ac-225 for cancer therapy indicates the potential need for its increased production and availability. This paper investigates the possibility of producing of Ac-225 in commercial quantities, which could potentially reduce obsolete radioactive material and displace the need for expensive importation of Ac-225 from the USA and Russia in the years ahead. Scaled up production of Ac-225 could theoretically be achieved by the use of a high current cyclotron or linac. Production specifications are determined for a linac in terms of current, pulse length and frequency, as well as an examination of other factors such as radiation issues and radionuclei separation. Yields are compared with those calculated for the Australian National Cyclotron in Sydney.

  13. Design and synthesis of 225Ac radioimmunopharmaceuticals.

    PubMed

    McDevitt, Michael R; Ma, Dangshe; Simon, Jim; Frank, R Keith; Scheinberg, David A

    2002-12-01

    The alpha-particle-emitting radionuclides 213Bi, 211At, 224Ra are under investigation for the treatment of leukemias, gliomas, and ankylosing spondylitis, respectively. 213Bi and 211At were attached to monoclonal antibodies and used as targeted immunotherapeutic agents while unconjugated 224Ra chloride selectively seeks bone. 225Ac possesses favorable physical properties for radioimmunotherapy (10d half-life and 4 net alpha particles), but has a history of unfavorable radiolabeling chemistry and poor metal-chelate stability. We selected functionalized derivatives of DOTA as the most promising to pursue from out of a group of potential 225Ac chelate compounds. A two-step synthetic process employing either MeO-DOTA-NCS or 2B-DOTA-NCS as the chelating moiety was developed to attach 225Ac to monoclonal antibodies. This method was tested using several different IgG systems. The chelation reaction yield in the first step was 93+/-8% radiochemically pure (n=26). The second step yielded 225Ac-DOTA-IgG constructs that were 95+/-5% radiochemically pure (n=27) and the mean percent immunoreactivity ranged from 25% to 81%, depending on the antibody used. This process has yielded several potential novel targeted 225Ac-labeled immunotherapeutic agents that may now be evaluated in appropriate model systems and ultimately in humans.

  14. Cosmic Shear - with ACS Pure Parallel Observations

    NASA Astrophysics Data System (ADS)

    Ratnatunga, Kavan

    2002-07-01

    The ACS, with greater sensitivity and sky coverage, will extend our ability to measure the weak gravitational lensing of galaxy images caused by the large scale distribution of dark matter. We propose to use the ACS in pure parallel {non- proprietary} mode, following the guidelines of the ACS Default Pure Parallel Program. Using the HST Medium Deep Survey WFPC2 database we have measured cosmic shear at arc-min angular scales. The MDS image parameters, in particular the galaxy orientations and axis ratios, are such that any residual corrections due to errors in the PSF or jitter are much smaller than the measured signal. This situation is in stark contrast with ground-based observations. We have also developed a statistical analysis procedure to derive unbiased estimates of cosmic shear from a large number of fields, each of which has a very small number of galaxies. We have therefore set the stage for measurements with the ACS at fainter apparent magnitudes and smaller, 10 arc-second scales corresponding to larger cosmological distances. We will adapt existing MDS WFPC2 maximum likelihood galaxy image analysis algorithms to work with the ACS. The analysis would also yield an online database similar to that in archive.stsci.edu/mds/

  15. ac propulsion system for an electric vehicle

    NASA Technical Reports Server (NTRS)

    Geppert, S.

    1980-01-01

    It is pointed out that dc drives will be the logical choice for current production electric vehicles (EV). However, by the mid-80's, there is a good chance that the price and reliability of suitable high-power semiconductors will allow for a competitive ac system. The driving force behind the ac approach is the induction motor, which has specific advantages relative to a dc shunt or series traction motor. These advantages would be an important factor in the case of a vehicle for which low maintenance characteristics are of primary importance. A description of an EV ac propulsion system is provided, taking into account the logic controller, the inverter, the motor, and a two-speed transmission-differential-axle assembly. The main barrier to the employment of the considered propulsion system in EV is not any technical problem, but inverter transistor cost.

  16. Atrial-caval shunting (ACS) after trauma.

    PubMed

    Kudsk, K A; Sheldon, G F; Lim, R C

    1982-02-01

    Since 1968 the atrial-caval shunt (ACS), along with inflow occlusion at the porta hepatis, has been used at San Francisco General Hospital in 18 trauma patients to control massive hemorrhage from the inferior vena cava, hepatic veins, or liver. Thirteen patients died from irreversible shock. Five patients survived their initial injuries; one of them died 45 days later from the complications of shock and sepsis. No patients survived who sustained blunt trauma and were admitted in cardiac arrest. Only one of ten patients with BP less than 70 mm Hg after resuscitation survived, whereas four of eight with BP greater than 70 mm Hg survived. ACS was used to control caval injuries in seven patients (one survivor), severe hepatic parenchymal fractures in four patients (two survivors), and combined hepatic and caval injuries in seven patients (two survivors). Survivors had an average of 5.75 associated injuries; nonsurvivors had 3.8. No complications of ACS occurred in the surviving patients.

  17. Beneficial Effects of Adenylyl Cyclase Type 6 (AC6) Expression Persist Using a Catalytically Inactive AC6 Mutant

    PubMed Central

    Tang, Tong; Lai, Ngai Chin; Miyanohara, Atsushi; Guo, Tracy; Tang, Rouying; Firth, Amy L.; Yuan, Jason X.; Hammond, H. Kirk

    2011-01-01

    Cardiac-directed expression of AC6 has pronounced favorable effects on cardiac function possibly not linked with cAMP production. To determine rigorously whether cAMP generation is required for the beneficial effects of increased AC6 expression, we generated a catalytically inactive AC6 mutant (AC6mut) that has markedly diminished cAMP generating capacity by replacing aspartic acid with alanine at position 426 in the C1 domain (catalytic region) of AC6. Gene transfer of AC6 or AC6mut (adenovirus-mediated) in adult rat cardiac myocytes resulted in similar expression levels and intracellular distribution, but AC6mut expression was associated with marked reduction in cAMP production. Despite marked reduction in cAMP generation, AC6mut influenced intracellular signaling events similarly to that observed after expression of catalytically intact AC6. For example, both AC6 and AC6mut reduced phenylephrine-induced cardiac myocyte hypertrophy and apoptosis (p < 0.001), expression of cardiac ankyrin repeat protein (p < 0.01), and phospholamban (p < 0.05). AC6mut expression, similar to its catalytically intact cohort, was associated with increased Ca2+ transients in cardiac myocytes after isoproterenol stimulation. Many of the biological effects of AC6 expression are replicated by a catalytically inactive AC6 mutant, indicating that the mechanisms for these effects do not require increased cAMP generation. PMID:21127130

  18. Transient AC voltage related phenomena for HVDC schemes connected to weak AC systems

    SciTech Connect

    Pilotto, L.A.S.; Szechtman, M. ); Hammad, A.E. )

    1992-07-01

    In this paper a didactic explanation of voltage stability associated phenomena at HVDC terminals is presented. Conditions leading to ac voltage collapse problems are identified. A mechanism that excites control-induced voltage oscillations is shown. The voltage stability factor is used for obtaining the maximum power limits of ac/dc systems operating with different control strategies. Correlation to Pd {times} Id curves is given. Solutions for eliminating the risks of voltage collapse and for avoiding control-induced oscillations are discussed. The results are supported by detailed digital simulations of a weak ac/dc system using EMTP.

  19. AcsA-AcsB: The core of the cellulose synthase complex from Gluconacetobacter hansenii ATCC23769.

    PubMed

    McManus, John B; Deng, Ying; Nagachar, Nivedita; Kao, Teh-hui; Tien, Ming

    2016-01-01

    The gram-negative bacterium, Gluconacetobacter hansenii, produces cellulose of exceptionally high crystallinity in comparison to the cellulose of higher plants. This bacterial cellulose is synthesized and extruded into the extracellular medium by the cellulose synthase complex (CSC). The catalytic component of this complex is encoded by the gene AcsAB. However, several other genes are known to encode proteins critical to cellulose synthesis and are likely components of the bacterial CSC. We have purified an active heterodimer AcsA-AcsB from G. hansenii ATCC23769 to homogeneity by two different methods. With the purified protein, we have determined how it is post-translationally processed, forming the active heterodimer AcsA-AcsB. Additionally, we have performed steady-state kinetic studies on the AcsA-AcsB complex. Finally through mutagenesis studies, we have explored the roles of the postulated CSC proteins AcsC, AcsD, and CcpAx. PMID:26672449

  20. AcsA-AcsB: The core of the cellulose synthase complex from Gluconacetobacter hansenii ATCC23769.

    PubMed

    McManus, John B; Deng, Ying; Nagachar, Nivedita; Kao, Teh-hui; Tien, Ming

    2016-01-01

    The gram-negative bacterium, Gluconacetobacter hansenii, produces cellulose of exceptionally high crystallinity in comparison to the cellulose of higher plants. This bacterial cellulose is synthesized and extruded into the extracellular medium by the cellulose synthase complex (CSC). The catalytic component of this complex is encoded by the gene AcsAB. However, several other genes are known to encode proteins critical to cellulose synthesis and are likely components of the bacterial CSC. We have purified an active heterodimer AcsA-AcsB from G. hansenii ATCC23769 to homogeneity by two different methods. With the purified protein, we have determined how it is post-translationally processed, forming the active heterodimer AcsA-AcsB. Additionally, we have performed steady-state kinetic studies on the AcsA-AcsB complex. Finally through mutagenesis studies, we have explored the roles of the postulated CSC proteins AcsC, AcsD, and CcpAx.

  1. A dry-cooled AC quantum voltmeter

    NASA Astrophysics Data System (ADS)

    Schubert, M.; Starkloff, M.; Peiselt, K.; Anders, S.; Knipper, R.; Lee, J.; Behr, R.; Palafox, L.; Böck, A. C.; Schaidhammer, L.; Fleischmann, P. M.; Meyer, H.-G.

    2016-10-01

    The paper describes a dry-cooled AC quantum voltmeter system operated up to kilohertz frequencies and 7 V rms. A 10 V programmable Josephson voltage standard (PJVS) array was installed on a pulse tube cooler (PTC) driven with a 4 kW air-cooled compressor. The operating margins at 70 GHz frequencies were investigated in detail and found to exceed 1 mA Shapiro step width. A key factor for the successful chip operation was the low on-chip power consumption of 65 mW in total. A thermal interface between PJVS chip and PTC cold stage was used to avoid a significant chip overheating. By installing the cryocooled PJVS array into an AC quantum voltmeter setup, several calibration measurements of dc standards and calibrator ac voltages up to 2 kHz frequencies were carried out to demonstrate the full functionality. The results are discussed and compared to systems with standard liquid helium cooling. For dc voltages, a direct comparison measurement between the dry-cooled AC quantum voltmeter and a liquid-helium based 10 V PJVS shows an agreement better than 1 part in 1010.

  2. AC power generation from microbial fuel cells

    NASA Astrophysics Data System (ADS)

    Lobo, Fernanda Leite; Wang, Heming; Forrestal, Casey; Ren, Zhiyong Jason

    2015-11-01

    Microbial fuel cells (MFCs) directly convert biodegradable substrates to electricity and carry good potential for energy-positive wastewater treatment. However, the low and direct current (DC) output from MFC is not usable for general electronics except small sensors, yet commercial DC-AC converters or inverters used in solar systems cannot be directly applied to MFCs. This study presents a new DC-AC converter system for MFCs that can generate alternating voltage in any desired frequency. Results show that AC power can be easily achieved in three different frequencies tested (1, 10, 60 Hz), and no energy storage layer such as capacitors was needed. The DC-AC converter efficiency was higher than 95% when powered by either individual MFCs or simple MFC stacks. Total harmonic distortion (THD) was used to investigate the quality of the energy, and it showed that the energy could be directly usable for linear electronic loads. This study shows that through electrical conversion MFCs can be potentially used in household electronics for decentralized off-grid communities.

  3. Manipulating Flames with AC Electric Fields

    NASA Astrophysics Data System (ADS)

    Bishop, Kyle

    2013-11-01

    Time-oscillating electric fields applied to plasmas present in flames create steady flows of gas capable of shaping, directing, enhancing, or even extinguishing flames. Interestingly, electric winds induced by AC electric fields can be stronger that those due to static fields of comparable magnitude. Furthermore, unlike static fields, the electric force due to AC fields is localized near the surface of the flame. Consequently, the AC response depends only on the local field at the surface of the flame - not on the position of the electrodes used to generate the field. These results suggest that oscillating electric fields can be used to manipulate and control combustion processes at a distance. To characterize and explain these effects, we investigate a simple experimental system comprising a laminar methane-air flame positioned between two parallel-plate electrodes. We quantify both the electric and hydrodynamic response of the flame as a function of frequency and magnitude of the applied field. A theoretical model shows how steady gas flows emerge from the time-averaged electrical force due to the field-induced motion of ions generated within the flame and by their disappearance by recombination. These results provide useful insights into the application of AC fields to direct combustion processes.

  4. Ac-dc converter firing error detection

    SciTech Connect

    Gould, O.L.

    1996-07-15

    Each of the twelve Booster Main Magnet Power Supply modules consist of two three-phase, full-wave rectifier bridges in series to provide a 560 VDC maximum output. The harmonic contents of the twelve-pulse ac-dc converter output are multiples of the 60 Hz ac power input, with a predominant 720 Hz signal greater than 14 dB in magnitude above the closest harmonic components at maximum output. The 720 Hz harmonic is typically greater than 20 dB below the 500 VDC output signal under normal operation. Extracting specific harmonics from the rectifier output signal of a 6, 12, or 24 pulse ac-dc converter allows the detection of SCR firing angle errors or complete misfires. A bandpass filter provides the input signal to a frequency-to-voltage converter. Comparing the output of the frequency-to-voltage converter to a reference voltage level provides an indication of the magnitude of the harmonics in the ac-dc converter output signal.

  5. High voltage AC/AC electrochemical capacitor operating at low temperature in salt aqueous electrolyte

    NASA Astrophysics Data System (ADS)

    Abbas, Qamar; Béguin, François

    2016-06-01

    We demonstrate that an activated carbon (AC)-based electrochemical capacitor implementing aqueous lithium sulfate electrolyte in 7:3 vol:vol water/methanol mixture can operate down to -40 °C with good electrochemical performance. Three-electrode cell investigations show that the faradaic contributions related with hydrogen chemisorption in the negative AC electrode are thermodynamically unfavored at -40 °C, enabling the system to work as a typical electrical double-layer (EDL) capacitor. After prolonged floating of the AC/AC capacitor at 1.6 V and -40°C, the capacitance, equivalent series resistance and efficiency remain constant, demonstrating the absence of ageing related with side redox reactions at this temperature. Interestingly, when temperature is increased back to 24 °C, the redox behavior due to hydrogen storage reappears and the system behaves as a freshly prepared one.

  6. 48 CFR Appendixes A-C to Chapter 7 - [Reserved

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false A Appendixes A-C to Chapter 7 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT Appendixes A-C to Chapter 7...

  7. 48 CFR Appendixes A-C to Chapter 7 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false A Appendixes A-C to Chapter 7 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT Appendixes A-C to Chapter 7...

  8. 21 CFR 886.1630 - AC-powered photostimulator.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...) Identification. An AC-powered photostimulator is an AC-powered device intended to provide light stimulus which allows measurement of retinal or visual function by perceptual or electrical methods (e.g.,...

  9. 21 CFR 880.5500 - AC-powered patient lift.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered patient lift. 880.5500 Section 880.5500 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Devices § 880.5500 AC-powered patient lift. (a) Identification. An AC-powered lift is an...

  10. Methods for Addressing Missing Data with Applications from ACS Exams

    ERIC Educational Resources Information Center

    Brandriet, Alexandra; Holme, Thomas

    2015-01-01

    As part of the ACS Examinations Institute (ACS-EI) national norming process, student performance data sets are collected from professors at colleges and universities from around the United States. Because the data sets are collected on a volunteer basis, the ACS-EI often receives data sets with only students' total scores and without the students'…

  11. 21 CFR 880.5500 - AC-powered patient lift.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false AC-powered patient lift. 880.5500 Section 880.5500... Devices § 880.5500 AC-powered patient lift. (a) Identification. An AC-powered lift is an electrically powered device either fixed or mobile, used to lift and transport patients in the horizontal or...

  12. 21 CFR 880.5500 - AC-powered patient lift.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false AC-powered patient lift. 880.5500 Section 880.5500... Devices § 880.5500 AC-powered patient lift. (a) Identification. An AC-powered lift is an electrically powered device either fixed or mobile, used to lift and transport patients in the horizontal or...

  13. 21 CFR 880.5500 - AC-powered patient lift.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false AC-powered patient lift. 880.5500 Section 880.5500... Devices § 880.5500 AC-powered patient lift. (a) Identification. An AC-powered lift is an electrically powered device either fixed or mobile, used to lift and transport patients in the horizontal or...

  14. 21 CFR 880.5500 - AC-powered patient lift.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false AC-powered patient lift. 880.5500 Section 880.5500... Devices § 880.5500 AC-powered patient lift. (a) Identification. An AC-powered lift is an electrically powered device either fixed or mobile, used to lift and transport patients in the horizontal or...

  15. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 11 2011-01-01 2011-01-01 false Area Coverage Survey (ACS). 1737.31 Section 1737.31... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  16. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 11 2013-01-01 2013-01-01 false Area Coverage Survey (ACS). 1737.31 Section 1737.31... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  17. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 11 2012-01-01 2012-01-01 false Area Coverage Survey (ACS). 1737.31 Section 1737.31... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  18. A HTS scanning magnet and AC operation

    NASA Astrophysics Data System (ADS)

    Hatanaka, K.; Nakagawa, J.; Fukuda, M.; Yorita, T.; Saito, T.; Sakemi, Y.; Kawaguchi, T.; Noda, K.

    2010-04-01

    A scanning magnet using high-temperature superconductor (HTS) wire was designed, built, and tested for its suitability as a beam scanner. After successful cooling tests, the magnet performance was studied using DC and AC currents. With DC current the magnet was successfully operated to generate designed field distributions and effective length. In AC mode, the magnet was operated at frequencies of 30-59 Hz and a temperature of 77 K as well as 10-20 Hz and 20 K. The power losses dissipated in the coils were measured and compared with the model calculations. The observed losses per cycle were independent of the frequency and the scaling law of the transport current was consistent with theoretical predictions for hysteretic losses in HTS wires.

  19. RHIC AC DIPOLE DESIGN AND CONSTRUCTION.

    SciTech Connect

    BAI,M.; METH,M.; PAI,C.; PARKER,B.; PEGGS,S.; ROSER,T.; SANDERS,R.; TRBOJEVIC,D.; ZALTSMAN,A.

    2001-06-18

    Two ac dipoles with vertical and horizontal magnetic field have been proposed at RHIC for applications in linear and non-linear beam dynamics and spin manipulations. A magnetic field amplitude of 380 Gm is required to produce a coherent oscillation of 5 times the rms beam size at the top energy. We take the ac dipole frequency to be 1.0% of the revolution frequency away from the betatron frequency. To achieve the strong magnetic field with minimum power loss, an air-core magnet with two seven turn winding of low loss Litz wire resonating at 64 kHz is designed. The system is also designed to allow one to connect the two magnet winding in series to resonate at 37 kHz for the spin manipulation. Measurements of a half length prototype magnet are also presented.

  20. THE ACS NEARBY GALAXY SURVEY TREASURY

    SciTech Connect

    Dalcanton, Julianne J.; Williams, Benjamin F.; Rosema, Keith; Gogarten, Stephanie M.; Christensen, Charlotte; Gilbert, Karoline; Hodge, Paul; Seth, Anil C.; Dolphin, Andrew; Holtzman, Jon; Skillman, Evan D.; Weisz, Daniel; Cole, Andrew; Girardi, Leo; Karachentsev, Igor D.; Olsen, Knut; Freeman, Ken; Gallart, Carme; De Jong, Roelof S. E-mail: ben@astro.washington.edu E-mail: stephanie@astro.washington.edu E-mail: fabio@astro.washington.edu E-mail: aseth@cfa.harvard.edu

    2009-07-15

    The ACS Nearby Galaxy Survey Treasury (ANGST) is a systematic survey to establish a legacy of uniform multi-color photometry of resolved stars for a volume-limited sample of nearby galaxies (D < 4 Mpc). The survey volume encompasses 69 galaxies in diverse environments, including close pairs, small and large groups, filaments, and truly isolated regions. The galaxies include a nearly complete range of morphological types spanning a factor of {approx}10{sup 4} in luminosity and star formation rate. The survey data consist of images taken with the Advanced Camera for Surveys (ACS) on the Hubble Space Telescope (HST), supplemented with archival data and new Wide Field Planetary Camera 2 (WFPC2) imaging taken after the failure of ACS. Survey images include wide field tilings covering the full radial extent of each galaxy, and single deep pointings in uncrowded regions of the most massive galaxies in the volume. The new wide field imaging in ANGST reaches median 50% completenesses of m {sub F475W} = 28.0 mag, m {sub F606W} = 27.3 mag, and m {sub F814W} = 27.3 mag, several magnitudes below the tip of the red giant branch (TRGB). The deep fields reach magnitudes sufficient to fully resolve the structure in the red clump. The resulting photometric catalogs are publicly accessible and contain over 34 million photometric measurements of >14 million stars. In this paper we present the details of the sample selection, imaging, data reduction, and the resulting photometric catalogs, along with an analysis of the photometric uncertainties (systematic and random), for both ACS and WFPC2 imaging. We also present uniformly derived relative distances measured from the apparent magnitude of the TRGB.

  1. AC plasma anemometer—characteristics and design

    NASA Astrophysics Data System (ADS)

    Marshall, Curtis; Matlis, Eric; Corke, Thomas; Gogineni, Sivaram

    2015-08-01

    The characteristics and design of a high-bandwidth flow sensor that uses an AC glow discharge (plasma) as the sensing element is presented. The plasma forms in the air gap between two protruding low profile electrodes attached to a probe body. The output from the anemometer is an amplitude modulated version of the AC voltage input that contains information about the mean and fluctuating velocity components. The anemometer circuitry includes resistance and capacitance elements that simulate a dielectric-barrier to maintain a diffuse plasma, and a constant-current feedback control that maintains operation within the desired glow discharge regime over an extended range of air velocities. Mean velocity calibrations are demonstrated over a range from 0 to 140 m s-1. Over this velocity range, the mean output voltage varied linearly with air velocity, providing a constant static sensitivity. The effect of the electrode gap and input AC carrier frequency on the anemometer static sensitivity and dynamic response are investigated. Experiments are performed to compare measurements obtained with a plasma sensor operating at two AC carrier frequencies against that of a constant-temperature hot-wire. All three sensors were calibrated against the same known velocity reference. An uncertainty based on the standard deviation of the velocity calibration fit was applied to the mean and fluctuating velocity measurements of the three sensors. The motivation is not to replace hot-wires as a general measurement tool, but rather as an alternative to hot-wires in harsh environments or at high Mach numbers where they either have difficulty in surviving or lack the necessary frequency response.

  2. Graphs for Isotopes of 89-Ac (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides a graphic representation of nucleon separation energies and residual interaction parameters for isotopes of the chemical element 89-Ac (Actinium, atomic number Z = 89).

  3. Large aperture ac interferometer for optical testing.

    PubMed

    Moore, D T; Murray, R; Neves, F B

    1978-12-15

    A 20-cm clear aperture modified Twyman-Green interferometer is described. The system measures phase with an AC technique called phase-lock interferometry while scanning the aperture with a dual galvanometer scanning system. Position information and phase are stored in a minicomputer with disk storage. This information is manipulated with associated software, and the wavefront deformation due to a test component is graphically displayed in perspective and contour on a CRT terminal. PMID:20208642

  4. Highlights of the Dallas ACS Meeting

    NASA Astrophysics Data System (ADS)

    Wildeman, Thomas R.; Freilich, Mark; Kelter, Paul B.

    1998-06-01

    Without a doubt, a primary feature of the 1998 Spring National Meeting in Dallas was the High School Program, which was organized by George Hague, and the impact that the Texas teachers had on other participants. Over 150 teachers registered for the meeting and participated in the program. Their organizational skills were used to reinstitute the High School/College Interface Luncheon. (The High School/College Interface Luncheon will also be held at the Fall ACS Meeting in Boston.)

  5. 78 FR 49318 - Availability of Draft Advisory Circular (AC) 90-106A and AC 20-167A

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-13

    ... Systems (78 FR 34935-34958) (Docket No.: FAA-2013-0485; Notice No. 1209). AC 90-106A, Enhanced Flight... the Federal Register published on April 11, 2000 (65 FR 19477-19478), as well as at http://DocketsInfo... Federal Aviation Administration Availability of Draft Advisory Circular (AC) 90-106A and AC 20-...

  6. Level structure and reflection asymmetric shape in sup 223 Ac

    SciTech Connect

    Sheline, R.K.; Liang, C.F.; Paris, P. )

    1990-07-20

    Mass separated sources of {sup 227}Pa (separated as PaF{sub 4}{sup +} ions) were used to study the level structure of {sup 223}Ac following alpha decay. The levels in {sup 223}Ac are interpreted as K = 5/2{sup {plus minus}} parity doublet bands which occur naturally in reflection asymmetric models and the multiphonon octupole model. The anomalous structure of the K = 3/2{sup {minus}} band is explained in terms of Coriolis coupling. The low lying parity doublet bands in {sup 223}Ac, {sup 225}Ac, and {sup 227}Ac are compared and contrasted.

  7. Development of a hardware-based AC microgrid for AC stability assessment

    NASA Astrophysics Data System (ADS)

    Swanson, Robert R.

    As more power electronic-based devices enable the development of high-bandwidth AC microgrids, the topic of microgrid power distribution stability has become of increased interest. Recently, researchers have proposed a relatively straightforward method to assess the stability of AC systems based upon the time-constants of sources, the net bus capacitance, and the rate limits of sources. In this research, a focus has been to develop a hardware test system to evaluate AC system stability. As a first step, a time domain model of a two converter microgrid was established in which a three phase inverter acts as a power source and an active rectifier serves as an adjustable constant power AC load. The constant power load can be utilized to create rapid power flow transients to the generating system. As a second step, the inverter and active rectifier were designed using a Smart Power Module IGBT for switching and an embedded microcontroller as a processor for algorithm implementation. The inverter and active rectifier were designed to operate simultaneously using a synchronization signal to ensure each respective local controller operates in a common reference frame. Finally, the physical system was created and initial testing performed to validate the hardware functionality as a variable amplitude and variable frequency AC system.

  8. Molecular biology of maize Ac/Ds elements: an overview.

    PubMed

    Lazarow, Katina; Doll, My-Linh; Kunze, Reinhard

    2013-01-01

    Maize Activator (Ac) is one of the prototype transposable elements of the hAT transposon superfamily, members of which were identified in plants, fungi, and animals. The autonomous Ac and nonautonomous Dissociation (Ds) elements are mobilized by the single transposase protein encoded by Ac. To date Ac/Ds transposons were shown to be functional in approximately 20 plant species and have become the most widely used transposable elements for gene tagging and functional genomics approaches in plants. In this chapter we review the biology, regulation, and transposition mechanism of Ac/Ds elements in maize and heterologous plants. We discuss the parameters that are known to influence the functionality and transposition efficiency of Ac/Ds transposons and need to be considered when designing Ac transposase expression constructs and Ds elements for application in heterologous plant species.

  9. An automatic AC/DC thermal voltage converter and AC voltage calibration system

    NASA Astrophysics Data System (ADS)

    Lentner, K. J.; Flach, D. R.; Bell, B. A.

    1985-10-01

    An automatic ac/dc difference calibration system is described which uses direct measurement of thermoelement emfs. In addition to ac/dc difference testing, the system can be used to measure some important characteristics of thermoelements, as well as to calibrate ac voltage calibrators and precision voltmeters. The system operates over a frquency range from 20 Hz to 100 kHz, covering the voltage range from 0.5 V to 1 kv. For all voltages the total measurement uncertainties expected (including the uncertainty of the specific reference thermal converters used) were 50 parts per million (ppm) at frequencies from 20 Hz to 20 kHz, inclusive, and 100 ppm at higher frequencies up to 100 kHz.

  10. Automatic ac/dc thermal voltage converter and ac voltage calibration system

    NASA Astrophysics Data System (ADS)

    Lentner, K. J.; Flach, D. R.; Bell, B. A.

    1984-11-01

    An automatic ac/dc difference calibration system is described which uses direct measurement of thermoelement emfs. In addition to ac/dc difference testing, the system can be used to measure some important characteristics of thermoelements, as well as to calibrate ac voltage calibrators and precision voltmeters. The system operates over a frequency range from 20 Hz to 100 kHz, covering the voltage range from 0.5 V to 1 kv. For all voltages the total measurement uncertainties expected (including the uncertainty of the specific reference thermal converters used) were 50 parts per million (ppm) at frequencies from 20 Hz to 20 kHz, inclusive, and 100 ppm at higher frequencies up to 100 kHz.

  11. Deletion of the AcMNPV core gene ac109 results in budded virions that are non-infectious

    SciTech Connect

    Fang Minggang; Nie, Yingchao; Theilmann, David A.

    2009-06-20

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac109 is a core gene and its function in the virus life cycle is unknown. To determine its role in the baculovirus life cycle, we used the AcMNPV bacmid system to generate an ac109 deletion virus (vAc{sup 109KO}). Fluorescence and light microscopy showed that transfection of vAc{sup 109KO} results in a single-cell infection phenotype. Viral DNA replication is unaffected and the development of occlusion bodies in vAc{sup 109KO}-transfected cells evidenced progression to the very late phases of viral infection. Western blot and confocal immunofluorescence analysis showed that AC109 is expressed in the cytoplasm and nucleus throughout infection. In addition, AC109 is a structural protein as it was detected in both budded virus (BV) and occlusion derived virus in both the envelope and nucleocapsid fractions. Titration assays by qPCR and TCID{sub 50} showed that vAc{sup 109KO} produced BV but the virions are non-infectious. The vAc{sup 109KO} BV were indistinguishable from the BV of repaired and wild type control viruses as determined by negative staining and electron microscopy.

  12. Deletion of the AcMNPV core gene ac109 results in budded virions that are non-infectious.

    PubMed

    Fang, Minggang; Nie, Yingchao; Theilmann, David A

    2009-06-20

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac109 is a core gene and its function in the virus life cycle is unknown. To determine its role in the baculovirus life cycle, we used the AcMNPV bacmid system to generate an ac109 deletion virus (vAc(109KO)). Fluorescence and light microscopy showed that transfection of vAc(109KO) results in a single-cell infection phenotype. Viral DNA replication is unaffected and the development of occlusion bodies in vAc(109KO)-transfected cells evidenced progression to the very late phases of viral infection. Western blot and confocal immunofluorescence analysis showed that AC109 is expressed in the cytoplasm and nucleus throughout infection. In addition, AC109 is a structural protein as it was detected in both budded virus (BV) and occlusion derived virus in both the envelope and nucleocapsid fractions. Titration assays by qPCR and TCID(50) showed that vAc(109KO) produced BV but the virions are non-infectious. The vAc(109KO) BV were indistinguishable from the BV of repaired and wild type control viruses as determined by negative staining and electron microscopy.

  13. A.C. Susceptometry Utilizing GMR sensors

    NASA Astrophysics Data System (ADS)

    Christy, Daniel; Shivaram, Bellave

    2001-11-01

    Superconducting quantum interference (SQUID) magnetometers remain as the most sensitive instruments to measure magnetic properties. However, the ready availability and rapid improvements in the sensitivity of magnetic field sensors based on giant magnetoresistance (GMR) effect combined with their low cost and ability to operate at room temperature opens up opportunities to exploit these new devices where the utmost sensitivity of SQUID based detection is not needed. In this article we present one such application of GMR sensors and demonstrate how they can enhance the signals obtained in a simple a.c. magnetic susceptibility apparatus.

  14. Ac irreversibility line of bismuth-based high temperature superconductors

    SciTech Connect

    Mehdaoui, A.; Beille, J.; Berling, D.; Loegel, B.; Noudem, J.G.; Tournier, R.

    1997-09-01

    We discuss the magnetic properties of lead doped Bi-2223 bulk samples obtained through combined magnetic melt texturing and hot pressing (MMTHP). The ac complex susceptibility measurements are achieved over a broad ac field range (1 Oe{lt}h{sub ac}{lt}100 Oe) and show highly anisotropic properties. The intergranular coupling is improved in the direction perpendicular to the applied stress and magnetic field direction, and an intragranular loss peak is observed for the first time. A comparison is made with other bismuth-based compounds and it is shown that the MMTHP process shifts the ac irreversibility line (ac IL) toward higher fields. It is also shown that all the ac IL{close_quote}s for quasi 2D bismuth-based compounds show a nearly quadratic temperature dependence and deviate therefore strongly from the linear behavior observed in quasi 3D compounds and expected from a critical state model.{copyright} {ital 1997 Materials Research Society.}

  15. AC Electroosmotic Pumping in Nanofluidic Funnels.

    PubMed

    Kneller, Andrew R; Haywood, Daniel G; Jacobson, Stephen C

    2016-06-21

    We report efficient pumping of fluids through nanofluidic funnels when a symmetric AC waveform is applied. The asymmetric geometry of the nanofluidic funnel induces not only ion current rectification but also electroosmotic flow rectification. In the base-to-tip direction, the funnel exhibits a lower ion conductance and a higher electroosmotic flow velocity, whereas, in the tip-to-base direction, the funnel has a higher ion conductance and a lower electroosmotic flow velocity. Consequently, symmetric AC waveforms easily pump fluid through the nanofunnels over a range of frequencies, e.g., 5 Hz to 5 kHz. In our experiments, the nanofunnels were milled into glass substrates with a focused ion beam (FIB) instrument, and the funnel design had a constant 5° taper with aspect ratios (funnel tip width to funnel depth) of 0.1 to 1.0. We tracked ion current rectification by current-voltage (I-V) response and electroosmotic flow rectification by transport of a zwitterionic fluorescent probe. Rectification of ion current and electroosmotic flow increased with increasing electric field applied to the nanofunnel. Our results support three-dimensional simulations of ion transport and electroosmotic transport through nanofunnels, which suggest the asymmetric electroosmotic transport stems from an induced pressure at the junction of the nanochannel and nanofunnel tip. PMID:27230495

  16. AC impedance analysis of polypyrrole thin films

    NASA Technical Reports Server (NTRS)

    Penner, Reginald M.; Martin, Charles R.

    1987-01-01

    The AC impedance spectra of thin polypyrrole films were obtained at open circuit potentials from -0.4 to 0.4 V vs SCE. Two limiting cases are discussed for which simplified equivalent circuits are applicable. At very positive potentials, the predominantly nonfaradaic AC impedance of polypyrrole is very similar to that observed previously for finite porous metallic films. Modeling of the data with the appropriate equivalent circuit permits effective pore diameter and pore number densities of the oxidized film to be estimated. At potentials from -0.4 to -0.3 V, the polypyrrole film is essentially nonelectronically conductive and diffusion of polymer oxidized sites with their associated counterions can be assumed to be linear from the film/substrate electrode interface. The equivalent circuit for the polypyrrole film at these potentials is that previously described for metal oxide, lithium intercalation thin films. Using this model, counterion diffusion coefficients are determined for both semi-infinite and finite diffusion domains. In addition, the limiting low frequency resistance and capacitance of the polypyrrole thin fims was determined and compared to that obtained previously for thicker films of the polymer. The origin of the observed potential dependence of these low frequency circuit components is discussed.

  17. AC electric field for rapid assembly of nanostructured polyaniline onto microsized gap for sensor devices.

    PubMed

    La Ferrara, Vera; Rametta, Gabriella; De Maria, Antonella

    2015-07-01

    Interconnected network of nanostructured polyaniline (PANI) is giving strong potential for enhancing device performances than bulk PANI counterparts. For nanostructured device processing, the main challenge is to get prototypes on large area by requiring precision, low cost and high rate assembly. Among processes meeting these requests, the alternate current electric fields are often used for nanostructure assembling. For the first time, we show the assembly of nanostructured PANI onto large electrode gaps (30-60 μm width) by applying alternate current electric fields, at low frequencies, to PANI particles dispersed in acetonitrile (ACN). An important advantage is the short assembly time, limited to 5-10 s, although electrode gaps are microsized. That encouraging result is due to a combination of forces, such as dielectrophoresis (DEP), induced-charge electrokinetic (ICEK) flow and alternate current electroosmotic (ACEO) flow, which speed up the assembly process when low frequencies and large electrode gaps are used. The main achievement of the present study is the development of ammonia sensors created by direct assembling of nanostructured PANI onto electrodes. Sensors exhibit high sensitivity to low gas concentrations as well as excellent reversibility at room temperature, even after storage in air.

  18. AC corrosion -- A new challenge to pipeline integrity

    SciTech Connect

    Gummow, R.A.; Wakelin, R.G.; Segall, S.M.

    1998-12-31

    Corrosion of steel by alternating current was investigated as far back as the early 1900`s. These early studies and others in the 1950--60`s indicated that AC corrosion of steel was only a fraction of an equivalent amount of direct current (i.e. less than 1% of a like amount of DC) and in addition was controlled to negligible levels when cathodic protection was applied to industry standards. In 1986 however, an investigation into a corrosion failure on a high pressure gas pipeline in Germany indicated that the sole cause of the failure was AC corrosion. This corrosion failure on an otherwise well protected pipeline resulted in the initiation of several laboratory and field studies which indicated, that above a certain minimum AC current density, normal levels of cathodic protection will not control AC corrosion to acceptable levels and that AC mitigation is often required to prevent serious corrosion. Several other AC corrosion sites were discovered at coating holidays during the follow-up investigations in Germany. A graph, relating AC voltage to holiday size at the minimum AC current density for corrosion, is presented to assist the pipeline operator in determining whether or not a pipeline is susceptible to AC corrosion activity.

  19. AC corrosion -- a new threat to pipeline integrity?

    SciTech Connect

    Gummow, R.A.; Wakelin, R.G.; Segall, S.M.

    1996-12-31

    Corrosion of steel by alternating current was investigated as far back as the early 1900`s. These early studies and others in the 1950--60`s indicated that AC corrosion of steel was only a fraction of an equivalent amount of direct current (i.e., less than 1% of a like amount of DC) and in addition was controlled to negligible levels with cathodic protection applied to industry standards. In 1986 however, an investigation into a corrosion failure on a high pressure gas pipeline in Germany indicated that the sole cause of the failure was AC corrosion. This corrosion failure on an otherwise well protected pipeline resulted in several laboratory and field studies which indicated, that above a certain minimum AC current density, standard levels of cathodic protection will not control AC corrosion and AC mitigation is required to prevent further corrosion. Several other corrosion anomalies were discovered at coating holidays during the follow-up investigations in Germany. The authors have investigated several corrosion occurrences on pipelines in Ontario during the last 2--3 years which appear to be caused by AC corrosion. This presentation traces the literature record on AC electrolysis from the past to the present and discusses the key parameters which determine the likelihood of corrosion attack. Several case histories of suspected AC corrosion will be discussed and guidelines on how to assess whether or not a pipeline is susceptible to AC corrosion will be offered.

  20. Fabrication of alumina films with laminated structures by ac anodization

    NASA Astrophysics Data System (ADS)

    Segawa, Hiroyo; Okano, Hironaga; Wada, Kenji; Inoue, Satoru

    2014-02-01

    Anodization techniques by alternating current (ac) are introduced in this review. By using ac anodization, laminated alumina films are fabricated. Different types of alumina films consisting of 50-200 nm layers were obtained by varying both the ac power supply and the electrolyte. The total film thickness increased with an increase in the total charge transferred. The thickness of the individual layers increased with the ac voltage; however, the anodization time had little effect on the film thickness. The laminated alumina films resembled the nacre structure of shells, and the different morphologies exhibited by bivalves and spiral shells could be replicated by controlling the rate of increase of the applied potentials.

  1. [Intestinal occlusion and abdominal compartment syndrome (ACS)].

    PubMed

    Stagnitti, Franco

    2009-01-01

    Intestinal occlusion is defined as an independent predictive factor of intra-abdominal hypertension (IAH) which represents an independent predictor of mortality. Baggot in 1951 classified patients operated with intestinal occlusion as being at risk for IAH ("abdominal blow-out"), recommending them for open abdomen surgery proposed by Ogilvie. Abdominal surgery provokes IAH in 44.7% of cases with mortality which, in emergency, triples with respect to elective surgery (21.9% vs 6.8%). In particular, IAH is present in 61.2% of ileus and bowel distension and is responsible for 52% of mortality (54.8% in cases with intra-abdominal infection). These patients present with an increasing intra-abdominal pressure (IAP) which, over 20-25 mmHg, triggers an Abdominal Compartment Syndrome (ACS) with altered functions in some organs arriving at Multiple Organ Dysfunction Syndrome (MODS). The intestine normally covers 58% of abdominal volume but when there is ileus distension, intestinal pneumatosis develops (third space) which can occupy up to 90% of the entire cavity. At this moment, Gastro Intestinal Failure (GIF) can appear, which is a specific independent risk factor of mortality, motor of "Organ Failure". The pathophysiological evolution has many factors in 45% of cases: intestinal pneumatosis is associated with mucosal and serous edema, capillary leakage with an increase in extra-cellular volume and peritoneal fluid collections (fourth space). The successive loss of the mucous barrier permits a bacterial translocation which includes bacteria, toxins, pro-inflammatory factors and oxygen free radicals facilitating the passage from an intra-abdominal to inter-systemic vicious cyrcle. IAH provokes the raising of the diaphragm, and vascular and visceral compressions which induce hypertension in the various spaces with compartmental characteristics. These trigger hypertension in the renal, hepatic, pelvic, thoracic, cardiac, intracranial, orbital and lower extremity areas, giving

  2. Evidence on the Molecular Basis of the Ac/ac Adaptive Cyanogenesis Polymorphism in White Clover (Trifolium repens L.)

    PubMed Central

    Olsen, Kenneth M.; Hsu, Shih-Chung; Small, Linda L.

    2008-01-01

    White clover is polymorphic for cyanogenesis, with both cyanogenic and acyanogenic plants occurring in nature. This chemical defense polymorphism is one of the longest-studied and best-documented examples of an adaptive polymorphism in plants. It is controlled by two independently segregating genes: Ac/ac controls the presence/absence of cyanogenic glucosides; and Li/li controls the presence/absence of their hydrolyzing enzyme, linamarase. Whereas Li is well characterized at the molecular level, Ac has remained unidentified. Here we report evidence that Ac corresponds to a gene encoding a cytochrome P450 of the CYP79D protein subfamily (CYP79D15), and we describe the apparent molecular basis of the Ac/ac polymorphism. CYP79D orthologs catalyze the first step in cyanogenic glucoside biosynthesis in other cyanogenic plant species. In white clover, Southern hybridizations indicate that CYP79D15 occurs as a single-copy gene in cyanogenic plants but is absent from the genomes of ac plants. Gene-expression analyses by RT–PCR corroborate this finding. This apparent molecular basis of the Ac/ac polymorphism parallels our previous findings for the Li/li polymorphism, which also arises through the presence/absence of a single-copy gene. The nature of these polymorphisms may reflect white clover's evolutionary origin as an allotetraploid derived from cyanogenic and acyanogenic diploid progenitors. PMID:18458107

  3. Advanced ac powertrain for electric vehicles

    SciTech Connect

    Slicker, J.M.; Kalns, L.

    1985-01-01

    The design of an ac propulsion system for an electric vehicle includes a three-phase induction motor, transistorized PWM inverter/battery charger, microprocessor-based controller, and two-speed automatic transaxle. This system was built and installed in a Mercury Lynx test bed vehicle as part of a Department of Energy propulsion system development program. An integral part of the inverter is a 4-kw battery charger which utilizes one of the bridge transistors. The overall inverter strategy for this configuration is discussed. The function of the microprocessor-based controller is described. Typical test results of the total vehicle and each of its major components are given, including system efficiencies and test track performance results.

  4. Fuzzy efficiency optimization of AC induction motors

    NASA Technical Reports Server (NTRS)

    Jani, Yashvant; Sousa, Gilberto; Turner, Wayne; Spiegel, Ron; Chappell, Jeff

    1993-01-01

    This paper describes the early states of work to implement a fuzzy logic controller to optimize the efficiency of AC induction motor/adjustable speed drive (ASD) systems running at less than optimal speed and torque conditions. In this paper, the process by which the membership functions of the controller were tuned is discussed and a controller which operates on frequency as well as voltage is proposed. The membership functions for this dual-variable controller are sketched. Additional topics include an approach for fuzzy logic to motor current control which can be used with vector-controlled drives. Incorporation of a fuzzy controller as an application-specific integrated circuit (ASIC) microchip is planned.

  5. AcMNPV ac143 (odv-e18) is essential for mediating budded virus production and is the 30th baculovirus core gene.

    PubMed

    McCarthy, Christina B; Theilmann, David A

    2008-05-25

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac143 (odv-e18) is a late gene that encodes for a predicted 9.6 kDa structural protein that locates to the occlusion derived viral envelope and viral induced intranuclear microvesicles [Braunagel, S.C., He, H., Ramamurthy, P., and Summers, M.D. (1996). Transcription, translation, and cellular localization of three Autographa californica nuclear polyhedrosis virus structural proteins: ODV-E18, ODV-E35, and ODV-EC27. Virology 222, 100-114.]. In this study we demonstrate that ac143 is actually a previously unrecognized core gene and that it is essential for mediating budded virus production. To examine the role of ac143 in the baculovirus life cycle, we used the AcMNPV bacmid system to generate an ac143 knockout (KO) virus (AcBAC(ac142)(REP-ac143KO)). Fluorescence and light microscopy showed that infection by AcBAC(ac142)(REP-ac143KO) is limited to a single cell and titration assays confirmed that AcBAC(ac142)(REP-ac143KO) was unable to produce budded virus (BV). Progression to very late phases of the viral infection was evidenced by the development of occlusion bodies in the nuclei of transfected cells. This correlated with the fact that viral DNA replication was unaffected in AcBAC(ac142)(REP-ac143KO) transfected cells. The entire ac143 promoter, which includes three late promoter motifs, is contained within the ac142 open reading frame. Different deletion mutants of this region showed that the integrity of the ac142-ac143 core gene cluster was required for the bacmids to display wild-type patterns of viral replication, BV production and RNA transcription.

  6. AcMNPV ac143 (odv-e18) is essential for mediating budded virus production and is the 30th baculovirus core gene

    SciTech Connect

    McCarthy, Christina B.; Theilmann, David A.

    2008-05-25

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac143 (odv-e18) is a late gene that encodes for a predicted 9.6 kDa structural protein that locates to the occlusion derived viral envelope and viral induced intranuclear microvesicles [Braunagel, S.C., He, H., Ramamurthy, P., and Summers, M.D. (1996). Transcription, translation, and cellular localization of three Autographa californica nuclear polyhedrosis virus structural proteins: ODV-E18, ODV-E35, and ODV-EC27. Virology 222, 100-114.]. In this study we demonstrate that ac143 is actually a previously unrecognized core gene and that it is essential for mediating budded virus production. To examine the role of ac143 in the baculovirus life cycle, we used the AcMNPV bacmid system to generate an ac143 knockout (KO) virus (AcBAC{sup ac142REP-ac143KO}). Fluorescence and light microscopy showed that infection by AcBAC{sup ac142REP-ac143KO} is limited to a single cell and titration assays confirmed that AcBAC{sup ac142REP-ac143KO} was unable to produce budded virus (BV). Progression to very late phases of the viral infection was evidenced by the development of occlusion bodies in the nuclei of transfected cells. This correlated with the fact that viral DNA replication was unaffected in AcBAC{sup ac142REP-ac143KO} transfected cells. The entire ac143 promoter, which includes three late promoter motifs, is contained within the ac142 open reading frame. Different deletion mutants of this region showed that the integrity of the ac142-ac143 core gene cluster was required for the bacmids to display wild-type patterns of viral replication, BV production and RNA transcription.

  7. Preliminary Geologic Mapping of the Ac-S-3 Hemisphere of Ceres from NASA's Dawn Mission

    NASA Astrophysics Data System (ADS)

    Buczkowski, D. L.; Yingst, R. A.; Williams, D. A.; Scully, J. E. C.; Mest, S. C.; Crown, D. A.; Jaumann, R.; Russell, C. T.; Raymond, C. A.; Schenk, P. M.; Marchi, S.; O'Brien, D. P.; Nathues, A.; Hoffmann, M.; Schafer, M.; Platz, T.; Roatsch, T.; Kersten, E.; Preusker, F.; Stephan, K.

    2015-10-01

    NASA's Dawn spacecraft [1] was captured into orbit by the dwarf planet (1) Ceres on March 6, 2015. During the Approach phase capture was preceded and followed by a series of optical navigation and rotation characterization observations by Dawn's Framing Camera (FC) [2], which provided the first images of Ceres' surface. As was done at Vesta [3], the Dawn Science Team will conduct a geological mapping campaign at Ceres during the Nominal Mission, including iterative mapping using data obtained during each orbital phase. In this presentation we will describe the approach of the Ceres Mapping Campaign and discuss the preliminary geological mapping of the Ac-S-3 (180- 360˚E) hemisphere of Ceres.

  8. Wind-powered asynchronous AC/DC/AC converter system. [for electric power supply regulation

    NASA Technical Reports Server (NTRS)

    Reitan, D. K.

    1973-01-01

    Two asynchronous ac/dc/ac systems are modelled that utilize wind power to drive a variable or constant hertz alternator. The first system employs a high power 60-hertz inverter tie to the large backup supply of the power company to either supplement them from wind energy, storage, or from a combination of both at a preset desired current; rectifier and inverter are identical and operate in either mode depending on the silicon control rectifier firing angle. The second system employs the same rectification but from a 60-hertz alternator arrangement; it provides mainly dc output, some sinusoidal 60-hertz from the wind bus and some high harmonic content 60-hertz from an 800-watt inverter.

  9. Operation of AC Adapters Visualized Using Light-Emitting Diodes

    ERIC Educational Resources Information Center

    Regester, Jeffrey

    2016-01-01

    A bridge rectifier is a diamond-shaped configuration of diodes that serves to convert alternating current(AC) into direct current (DC). In our world of AC outlets and DC electronics, they are ubiquitous. Of course, most bridge rectifiers are built with regular diodes, not the light-emitting variety, because LEDs have a number of disadvantages. For…

  10. 24 CFR Appendices A-C to Subtitle A - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false A Appendices A-C to Subtitle A Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development Appendices A-C to Subtitle A...

  11. 24 CFR Appendices A-C to Subtitle A - [Reserved

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false A Appendices A-C to Subtitle A Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development Appendices A-C to Subtitle A...

  12. 24 CFR Appendices A-C to Subtitle A - [Reserved

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false A Appendices A-C to Subtitle A Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development Appendices A-C to Subtitle A...

  13. 24 CFR Appendixes A-C to Subtitle A - [Reserved

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false A Appendixes A-C to Subtitle A Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development Appendixes A-C to Subtitle A...

  14. 40 CFR Appendixes A-C to Part 403 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 28 2010-07-01 2010-07-01 true A Appendixes A-C to Part 403 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GENERAL PRE-TREAT-MENT REGULATIONS FOR EXIST-ING AND NEW SOURCES OF POLLUTION Appendixes A-C to Part 403...

  15. 40 CFR Appendixes A-C to Part 403 - [Reserved

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 29 2011-07-01 2009-07-01 true A Appendixes A-C to Part 403 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GENERAL PRE-TREAT-MENT REGULATIONS FOR EXIST-ING AND NEW SOURCES OF POLLUTION Appendixes A-C to Part 403...

  16. Electrostatic coalescence system with independent AC and DC hydrophilic electrodes

    DOEpatents

    Hovarongkura, A. David; Henry, Jr., Joseph D.

    1981-01-01

    An improved electrostatic coalescence system is provided in which independent AC and DC hydrophilic electrodes are employed to provide more complete dehydration of an oil emulsion. The AC field is produced between an AC electrode array and the water-oil interface wherein the AC electrode array is positioned parallel to the interface which acts as a grounded electrode. The emulsion is introduced into the AC field in an evenly distributed manner at the interface. The AC field promotes drop-drop and drop-interface coalescence of the water phase in the entering emulsion. The continuous oil phase passes upward through the perforated AC electrode array and enters a strong DC field produced between closely spaced DC electrodes in which small dispersed droplets of water entrained in the continuous phase are removed primarily by collection at hydrophilic DC electrodes. Large droplets of water collected by the electrodes migrate downward through the AC electrode array to the interface. All phase separation mechanisms are utilized to accomplish more complete phase separation.

  17. Undergraduate Chemistry Education: Report of an ACS Presidential Symposium

    ERIC Educational Resources Information Center

    Polik, William F.

    2006-01-01

    The American Chemical Society (ACS) Presidential Symposium, Envisioning Undergraduate Chemistry Education in 2015 was organized by the ACS Committee on Professional Training (CPT), in response to the challenge to envision the chemistry enterprise in 2015. The need for more diverse role models at all levels is emphasized, including high school…

  18. Measurement of coupling resonance driving terms with the AC dipole

    SciTech Connect

    Miyamoto, R.

    2010-10-01

    Resonance driving terms for linear coupled betatron motion in a synchrotron ring can be determined from corresponding spectral lines of an excited coherent beam motion. An AC dipole is one of instruments to excite such a motion. When a coherent motion is excited with an AC dipole, measured Courant-Snyder parameters and betatron phase advance have apparent modulations, as if there is an additional quadrupole field at the location of the AC dipole. Hence, measurements of these parameters using the AC dipole require a proper interpretation of observed quantities. The situation is similar in measurements of resonance driving terms using the AC dipole. In this note, we derive an expression of coupled betatron motion excited with two AC dipoles in presence of skew quadrupole fields, discuss an impact of this quadrupole like effect of the AC dipole on a measurement of coupling resonance driving terms, and present an analytical method to determine the coupling resonance driving terms from quantities observed using the AC dipole.

  19. 24 CFR Appendices A-C to Subtitle A - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false A Appendices A-C to Subtitle A Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development Appendices A-C to Subtitle A...

  20. 7 CFR 1737.31 - Area Coverage Survey (ACS).

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF... Studies-Area Coverage Survey and Loan Design § 1737.31 Area Coverage Survey (ACS). (a) The Area Coverage Survey (ACS) is a market forecast of service requirements of subscribers in a proposed service area....

  1. Equivalent circuit models for ac impedance data analysis

    NASA Technical Reports Server (NTRS)

    Danford, M. D.

    1990-01-01

    A least-squares fitting routine has been developed for the analysis of ac impedance data. It has been determined that the checking of the derived equations for a particular circuit with a commercially available electronics circuit program is essential. As a result of the investigation described, three equivalent circuit models were selected for use in the analysis of ac impedance data.

  2. HVDC-AC system interaction from AC harmonics. Volume 1. Harmonic impedance calculations. Final report

    SciTech Connect

    Breuer, G D; Chow, J H; Lindh, C B; Miller, N W; Numrich, F H; Price, W W; Turner, A E; Whitney, R R

    1982-09-01

    Improved methods are needed to characterize ac system harmonic behavior for ac filter design for HVDC systems. The purpose of this General Electric Company RP1138 research is to evaluate the present filter design practice and to investigate methods for calculating system harmonic impedances. An overview of ac filter design for HVDC systems and a survey of literature related to filter design have been performed. Two methods for calculating system harmonic impedances have been investigated. In the measurement method, an instrumentation system for measuring system voltage and current has been assembled. Different schemes of using the measurements to calculate system harmonic impedances have been studied. In the analytical method, a procedure to include various operating conditions has been proposed. Computer programs for both methods have been prepared, and the results of the measurement and analytical methods analyzed. A conclusion of the project is that the measurement and analytical methods both provided reasonable results. There are correlations between the measured and analytical results for most harmonics, although there are discrepancies between the assumptions used in the two methods. A sensitivity approach has been proposed to further correlate the results. From the results of the analysis, it is recommended that both methods should be tested further. For the measurement method, more testing should be done to cover different system operating conditions. In the analytical method, more detailed models for representing system components should be studied. In addition, alternative statistical and sensitivity approaches should be attempted.

  3. Sustainable AC/AC hybrid electrochemical capacitors in aqueous electrolyte approaching the performance of organic systems

    NASA Astrophysics Data System (ADS)

    Abbas, Qamar; Babuchowska, Paulina; Frąckowiak, Elżbieta; Béguin, François

    2016-09-01

    A high energy hybrid AC/AC electrochemical capacitor has been realized in aqueous Li2SO4+KI electrolyte mixture. Owing to the redox processes associated with the 2I-/I2 system, the positive electrode operates in narrow potential range and displays high capacity. During prolonged potentiostatic floating at 1.6 V, the hybrid cell demonstrates remarkably stable capacitance and resistance. Analyses by temperature programmed desorption after floating at 1.6 V proved that oxidation of the positive AC electrode is prevented by the use of Li2SO4+KI, which enables the maximum potential of this electrode to be shifted below the water oxidation potential. When charged at 0.2 A g-1 up to U = 1.6 V, the hybrid cell displays a high capacitance of 75 F g-1 (300 F g-1 per mass of one electrode) compared to 47 F g-1 (188 F g-1 per mass of one electrode) for a symmetric cell in Li2SO4. At 0.2 A g-1 up to 1.6 V, the hybrid capacitor in Li2SO4+KI displays an energy density of 26 Wh kg-1 which approaches the energy density of 30.9 Wh kg-1 measured when the same carbon is implemented in a capacitor using TEABF4/ACN electrolyte and charged up to 2.5 V.

  4. Cytotoxicity of 213Bi- and 225Ac-immunoconjugates.

    PubMed

    Kaspersen, F M; Bos, E; Doornmalen, A V; Geerlings, M W; Apostolidis, C; Molinet, R

    1995-06-01

    This paper describes in vitro cytotoxicity experiments with 213Bi- and 225Ac-immunoconjugates on the human epidermoid tumour cell line A431 using a blood group A-reactive murine IgG (2D11) as the specific antibody and MOPC 21 as the control antibody. With both radionuclides, specific cell-killing was achieved. The observed cytotoxicity of 213Bi (T1/2 - 47 min) indicates that this radionuclide is a useful alternative for the alpha-emitter 212Bi in the treatment of blood-borne malignancies. 225Ac-immunoconjugates (T1/2 of 225Ac is 10 days) may be applicable for the treatment of solid tumours, since the daughter radionuclides of 225Ac contribute to the cytotoxic efficacy by a field effect (i.e. toxicity in an area distal from the antibody-binding site). The lack of an adequate chelator for 225Ac is a major drawback.

  5. The A to Z of A/C plasmids.

    PubMed

    Harmer, Christopher J; Hall, Ruth M

    2015-07-01

    Plasmids belonging to incompatibility groups A and C (now A/C) were among the earliest to be associated with antibiotic resistance in Gram-negative bacteria. A/C plasmids are large, conjugative plasmids with a broad host range. The prevalence of A/C plasmids in collections of clinical isolates has revealed their importance in the dissemination of extended-spectrum β-lactamases and carbapenemases. They also mobilize SGI1-type resistance islands. Revived interest in the family has yielded many complete A/C plasmid sequences, revealing that RA1, designated A/C1, is different from the remainder, designated A/C2. There are two distinct A/C2 lineages. Backbones of 128-130 kb include over 120 genes or ORFs encoding proteins of at least 100 amino acids, but very few have been characterized. Genes potentially required for replication, stability and transfer have been identified, but only the replication system of RA1 and the regulation of transfer have been studied. There is enormous variety in the antibiotic resistance genes carried by A/C2 plasmids but they are usually clustered in larger regions at various locations in the backbone. The ARI-A and ARI-B resistance islands are always at a specific location but have variable content. ARI-A is only found in type 1 A/C2 plasmids, which disseminate blaCMY-2 and blaNDM-1 genes, whereas ARI-B, carrying the sul2 gene, is found in both type 1 and type 2. This review summarizes current knowledge of A/C plasmids, and highlights areas of research to be considered in the future.

  6. An Ac transposon system based on maize chromosome 4S for isolating long-distance-transposed Ac tags in the maize genome.

    PubMed

    Wang, Fei; Li, Zhaoying; Fan, Jun; Li, Pengfei; Hu, Wei; Wang, Gang; Xu, Zhengkai; Song, Rentao

    2010-12-01

    Transposon tagging is an important tool for gene isolation and functional studies. In maize, several transposon-tagging systems have been developed, mostly using Activator/Dissociation (Ac/Ds) and Mutator systems. Here, we establish another Ac-based transposon system with the donor Ac tightly linked with sugary1 (su1) on maize chromosome 4S. Newly transposed Ac (tr-Acs) were detected based on a negative dosage effect, and long-distance-transposed Ac events were identified and isolated from the donor Ac by a simple backcross scheme. In this study, we identified 208 independent long-distance-transposed Ac lines. Thirty-one flanking sequences of these tr-Acs were isolated and localized in the maize genome. As found in previous studies, the tr-Acs preferentially inserted into genic sequences. The distribution of tr-Acs is not random. In our study, the tr-Acs preferentially transposed into chromosomes 1, 2, 9 and 10. We discuss the preferential distribution of tr-Acs from Ac systems. Our system is complementary to two other Ac-based regional-mutagenesis systems in maize, and the combined use of these systems will achieve an even and high-density distribution of Ac elements throughout the maize genome for functional-genomics studies.

  7. Safety assessment of Cry1Ab/Ac fusion protein.

    PubMed

    Xu, Wentao; Cao, Sishuo; He, Xiaoyun; Luo, Yunbo; Guo, Xing; Yuan, Yanfang; Huang, Kunlun

    2009-07-01

    Cry1ab/ac gene was fused by both the cry1ab gene (GenBank Accession No. X54939) and the cry1ac gene (GenBank Accession No. Y09787), which was widely used in genetically modified (GM) rice, cotton, maize and so on. In order to support the safety assessment of GM food or feed products containing Cry1Ab/Ac protein, sufficient quantities of Cry1Ab/Ac protein were produced in Escherichia coli for in vitro evaluation and animal studies. The Cry1Ab/Ac protein does not possess the characteristics associated with food toxins or allergens, i.e., it has no sequence homology with any known allergens or toxins, and no N-glycosylation sites, can be rapidly degraded in gastric and intestinal fluids, and is devoid of adverse effects in mice by gavage at a high dose level of 5g (Cry1Ab/Ac protein)/kg body weight. In conclusion, there is a reasonable certainty of no harm resulting from the inclusion of the Cry1Ab/Ac protein in human food or animal feed.

  8. Trapping polar molecules in an ac trap

    SciTech Connect

    Bethlem, Hendrick L.; Veldhoven, Jacqueline van; Schnell, Melanie; Meijer, Gerard

    2006-12-15

    Polar molecules in high-field seeking states cannot be trapped in static traps as Maxwell's equations do not allow a maximum of the electric field in free space. It is possible to generate an electric field that has a saddle point by superposing an inhomogeneous electric field to an homogeneous electric field. In such a field, molecules are focused along one direction, while being defocused along the other. By reversing the direction of the inhomogeneous electric field the focusing and defocusing directions are reversed. When the fields are being switched back and forth at the appropriate rate, this leads to a net focusing force in all directions. We describe possible electrode geometries for creating the desired fields and discuss their merits. Trapping of {sup 15}ND{sub 3} ammonia molecules in a cylindrically symmetric ac trap is demonstrated. We present measurements of the spatial distribution of the trapped cloud as a function of the settings of the trap and compare these to both a simple model assuming a linear force and to full three-dimensional simulations of the experiment. With the optimal settings, molecules within a phase-space volume of 270 mm{sup 3} (m/s){sup 3} remain trapped. This corresponds to a trap depth of about 5 mK and a trap volume of about 20 mm{sup 3}.

  9. Cyclotron production of Ac-225 for targeted alpha therapy.

    PubMed

    Apostolidis, C; Molinet, R; McGinley, J; Abbas, K; Möllenbeck, J; Morgenstern, A

    2005-03-01

    The feasibility of producing Ac-225 by proton irradiation of Ra-226 in a cyclotron through the reaction Ra-226(p,2n)Ac-225 has been experimentally demonstrated for the first time. Proton energies were varied from 8.8 to 24.8 MeV and cross-sections were determined by radiochemical analysis of reaction yields. Maximum yields were reached at incident proton energies of 16.8 MeV. Radiochemical separation of Ac-225 from the irradiated target yielded a product suitable for targeted alpha therapy of cancer.

  10. Cyclotron production of Ac-225 for targeted alpha therapy.

    PubMed

    Apostolidis, C; Molinet, R; McGinley, J; Abbas, K; Möllenbeck, J; Morgenstern, A

    2005-03-01

    The feasibility of producing Ac-225 by proton irradiation of Ra-226 in a cyclotron through the reaction Ra-226(p,2n)Ac-225 has been experimentally demonstrated for the first time. Proton energies were varied from 8.8 to 24.8 MeV and cross-sections were determined by radiochemical analysis of reaction yields. Maximum yields were reached at incident proton energies of 16.8 MeV. Radiochemical separation of Ac-225 from the irradiated target yielded a product suitable for targeted alpha therapy of cancer. PMID:15607913

  11. ISTTOK upgrade towards AC and remote operation

    NASA Astrophysics Data System (ADS)

    Fernandes, H.; Silva, C.; Carvalho, B.; Sousa, J.; Valcárcel, D.; Neto, A.; Fortunato, J.; Carvalho, I.; Varandas, C. A. F.

    2006-12-01

    ISTTOK has performed one of the earliest experiments of AC tokamak operation showing that long discharges could be produced merely with inductive current drive. However, due to the design of the machine, the data acquisition system and the power supplies, a limit of 250 ms (six times the nominal forward shot duration) is currently imposed. In this paper the relevant constrains to attain current operation up to the limit of the stable toroidal magnetic field (3s) are discussed and the work being carried out to achieve this goal is presented. The conditions that shall be accomplished are: (i) removing the power deposited on the limiters; (ii) density control through gas puffing and monitoring the recycling from the walls; (iii) assessment of the free magnetic flux available on the iron core (Wmax=0.2 Vs); (iv) reformulation of the data acquisition system towards an event driven philosophy maintaining the actual distributed architecture but allowing a real-time control; (v) active control of the equilibrium magnetic fields implementing a digital plasma position estimator and actuator through new power supplies for the poloidal magnetic fields. As a new high level software was needed to implement all this features, the ISTTOK data acquisition system and control has been totally redesigned in JAVA/SQL database technology and time stamps events were adopted to catalogue the data. This software has been design keeping in mind the needs for remote participation and operation of the machine. Therefore, a cooperative environment has been implemented where several persons can be connected together to the platform, programming their own devices and exchanging knowledge or opinions through an embedded chat.

  12. ISTTOK upgrade towards AC and remote operation

    SciTech Connect

    Fernandes, H.; Silva, C.; Carvalho, B.; Sousa, J.; Valcarcel, D.; Neto, A.; Fortunato, J.; Carvalho, I.; Varandas, C. A. F.

    2006-12-04

    ISTTOK has performed one of the earliest experiments of AC tokamak operation showing that long discharges could be produced merely with inductive current drive. However, due to the design of the machine, the data acquisition system and the power supplies, a limit of 250 ms (six times the nominal forward shot duration) is currently imposed.In this paper the relevant constrains to attain current operation up to the limit of the stable toroidal magnetic field (3s) are discussed and the work being carried out to achieve this goal is presented.The conditions that shall be accomplished are: (i) removing the power deposited on the limiters; (ii) density control through gas puffing and monitoring the recycling from the walls; (iii) assessment of the free magnetic flux available on the iron core (Wmax=0.2 Vs); (iv) reformulation of the data acquisition system towards an event driven philosophy maintaining the actual distributed architecture but allowing a real-time control; (v) active control of the equilibrium magnetic fields implementing a digital plasma position estimator and actuator through new power supplies for the poloidal magnetic fields. As a new high level software was needed to implement all this features, the ISTTOK data acquisition system and control has been totally redesigned in JAVA/SQL database technology and time stamps events were adopted to catalogue the data. This software has been design keeping in mind the needs for remote participation and operation of the machine. Therefore, a cooperative environment has been implemented where several persons can be connected together to the platform, programming their own devices and exchanging knowledge or opinions through an embedded chat.

  13. Initial Tests of an AC Dipole for the Tevatron

    SciTech Connect

    Miyamoto, R.; Kopp, S.; Jansson, A.; Syphers, M.

    2006-11-20

    The AC dipole is a device to diagnose transverse motions of a beam. It can achieve large-amplitude oscillations without two inevitable problems of conventional kicker/pinger magnets: decoherence and emittance growth. While not the first synchrotron to operate with an AC dipole, the Tevatron can now make use of its recently upgraded BPM system, providing unprecedented resolution for use with an AC dipole, to measure both linear and nonlinear properties of the accelerator. Plans are to provide AC dipole systems for both transverse degrees of freedom. Preliminary tests have been done using an audio power amplifier with an existing vertical pinger magnet, producing oscillation amplitudes up to 2{sigma} at 150 GeV. In this paper, we will present the configuration of this system. We also show the analysis of a first few data sets, including the direct measurement of beta functions at BPM locations.

  14. Initial Tests of an AC Dipole for the Tevatron

    NASA Astrophysics Data System (ADS)

    Miyamoto, R.; Jansson, A.; Kopp, S.; Syphers, M.

    2006-11-01

    The AC dipole is a device to diagnose transverse motions of a beam. It can achieve large-amplitude oscillations without two inevitable problems of conventional kicker/pinger magnets: decoherence and emittance growth. While not the first synchrotron to operate with an AC dipole, the Tevatron can now make use of its recently upgraded BPM system, providing unprecedented resolution for use with an AC dipole, to measure both linear and nonlinear properties of the accelerator. Plans are to provide AC dipole systems for both transverse degrees of freedom. Preliminary tests have been done using an audio power amplifier with an existing vertical pinger magnet, producing oscillation amplitudes up to 2σ at 150 GeV. In this paper, we will present the configuration of this system. We also show the analysis of a first few data sets, including the direct measurement of beta functions at BPM locations.

  15. Initial tests of an AC dipole for the Tevatron

    SciTech Connect

    Miyamoto, R.; Jansson, A.; Kopp, S.; Syphers, M.; /Fermilab

    2006-06-01

    The AC dipole is a device to diagnose transverse motions of a beam. It can achieve large-amplitude oscillations without two inevitable problems of conventional kicker/pinger magnets: decoherence and emittance growth. While not the first synchrotron to operate with an AC dipole, the Tevatron can now make use of its recently upgraded BPM system, providing unprecedented resolution for use with an AC dipole, to measure both linear and nonlinear properties of the accelerator. Plans are to provide AC dipole systems for both transverse degrees of freedom. Preliminary tests have been done using an audio power amplifier with an existing vertical pinger magnet, producing oscillation amplitudes up to 2{sigma} at 150 GeV. In this paper, we will present the configuration of this system. We also show the analysis of a first few data sets, including the direct measurement of beta functions at BPM locations.

  16. High-Frequency ac Power-Distribution System

    NASA Technical Reports Server (NTRS)

    Hansen, Irving G.; Mildice, James

    1987-01-01

    Loads managed automatically under cycle-by-cycle control. 440-V rms, 20-kHz ac power system developed. System flexible, versatile, and "transparent" to user equipment, while maintaining high efficiency and low weight. Electrical source, from dc to 2,200-Hz ac converted to 440-V rms, 20-kHz, single-phase ac. Power distributed through low-inductance cables. Output power either dc or variable ac. Energy transferred per cycle reduced by factor of 50. Number of parts reduced by factor of about 5 and power loss reduced by two-thirds. Factors result in increased reliability and reduced costs. Used in any power-distribution system requiring high efficiency, high reliability, low weight, and flexibility to handle variety of sources and loads.

  17. Fast electric dipole transitions in Ra-Ac nuclei

    SciTech Connect

    Ahmad, I.

    1985-01-01

    Lifetime of levels in /sup 225/Ra, /sup 225/Ac, and /sup 227/Ac have been measured by delayed coincidence techniques and these have been used to determine the E1 gamma-ray transition probabilities. The reduced E1 transition probabilities. The reduced E1 transition probabilities in /sup 225/Ra and /sup 225/Ac are about two orders of magnitude larger than the values in mid-actinide nuclei. On the other hand, the E1 rate in /sup 227/Ac is similar to those measured in heavier actinides. Previous studies suggest the presence of octupole deformation in all the three nuclei. The present investigation indicates that fast E1 transitions occur for nuclei with octupole deformation. However, the studies also show that there is no one-to-one correspondence between E1 rate and octupole deformation. 13 refs., 4 figs.

  18. Effect of ac on current-induced domain wall motion

    NASA Astrophysics Data System (ADS)

    Kim, W. J.; Lee, T. D.; Choa, S. H.; Seo, S. M.; Lee, K. J.

    2007-05-01

    Saitoh et al. [Nature (London) 432, 203 (2004)] have reported the experimental result showing the interplay of a transverse domain wall with an electrical ac of megahertz-range frequencies. They observed a single peak of resistance in the frequency range and interpreted it with a nonadiabatic spin torque. It was argued that an ac current can induce a micrometer-range displacement of domain wall. We reconstructed the experiment in micromagnetic simulations considering the local nonzero nonadiabatic spin torque. We could not observe either an explicit single peak in the frequency-dependent resistance or an eventual displacement of domain wall by use of an ac. It indicates the local nonadiabatic torque is inappropriate to explain the experimental results of ac-induced domain wall motion. Other approaches such as the nonlocal nonadiabatic spin torque may be needed.

  19. Instrument sequentially samples ac signals from several accelerometers

    NASA Technical Reports Server (NTRS)

    Chapman, C. P.

    1967-01-01

    Scanner circuit sequentially samples the ac signals from accelerometers used in conducting noise vibration tests, and provides a time-averaged output signal. The scanner is used in conjunction with other devices for random noise vibration tests.

  20. Basic concepts of induced AC voltages on pipelines

    SciTech Connect

    Kirkpatrick, E.L.

    1995-07-01

    The phenomena of induced AC on pipelines sharing common rights-of-way with overhead high-voltage electrical transmission power lines is discussed. Basic concepts and techniques for personnel safety and some pipeline protective measures are reviewed.

  1. Absorption and Attenuation Coefficients Using the WET Labs ac-s in the Mid-Atlantic Bight: Field Measurements and Data Analysis

    NASA Technical Reports Server (NTRS)

    Ohi, Nobuaki; Makinen, Carla P.; Mitchell, Richard; Moisan, Tiffany A.

    2008-01-01

    Ocean color algorithms are based on the parameterization of apparent optical properties as a function of inherent optical properties. WET Labs underwater absorption and attenuation meters (ac-9 and ac-s) measure both the spectral beam attenuation [c (lambda)] and absorption coefficient [a (lambda)]. The ac-s reports in a continuous range of 390-750 nm with a band pass of 4 nm, totaling approximately 83 distinct wavelengths, while the ac-9 reports at 9 wavelengths. We performed the ac-s field measurements at nine stations in the Mid-Atlantic Bight from water calibrations to data analysis. Onboard the ship, the ac-s was calibrated daily using Milli Q-water. Corrections for the in situ temperature and salinity effects on optical properties of water were applied. Corrections for incomplete recovery of the scattered light in the ac-s absorption tube were performed. The fine scale of spectral and vertical distributions of c (lambda) and a (lambda) were described from the ac-s. The significant relationships between a (674) and that of spectrophotometric analysis and chlorophyll a concentration of discrete water samples were observed.

  2. Alternating parity structure in doubly odd /sup 218/Ac

    SciTech Connect

    Debray, M.E.; Davidson, M.; Kreiner, A.J.; Davidson, J.; Falcone, G.; Hojman, D.; Santos, D.

    1989-03-01

    States in doubly odd /sup 218/Ac have been studied using in-beam ..cap alpha..-, ..gamma..-, and e/sup -/-spectroscopy techniques mainly through the /sup 209/Bi(/sup 12/C,3n)= fusion-evaporation reaction. /sup 218/Ac shows a band structure, with interleaved states of alternating parities connected by enhanced B(E1) transitions, which is strikingly similar to the one in its isotone /sup 217/Ra.

  3. Search for {beta}-delayed fission of {sup 228}Ac

    SciTech Connect

    Xu Yanbing; Ding Huajie; Yuan Shuanggui; Yang Weifan; Niu Yanning; Li Yingjun; Xiao Yonghou; Zhang Shengdong; Lu Xiting

    2006-10-15

    Radium was radiochemically separated from natural thorium. Thin {sup 228}Ra{yields}{beta}{sup -228}Ac sources were prepared and exposed to mica fission track detectors, and measured by an HPGe {gamma}-ray detector. The {beta}-delayed fission events of {sup 228}Ac were observed and its {beta}-delayed fission probability was found to be (5{+-}2)x10{sup -12}.

  4. Development of an AC Module System: Final Technical Report

    SciTech Connect

    Suparna Kadam; Miles Russell

    2012-06-15

    The GreenRay Inc. program focused on simplifying solar electricity and making it affordable and accessible to the mainstream population. This was accomplished by integrating a solar module, micro-inverter, mounting and monitoring into a reliable, 'plug and play' AC system for residential rooftops, offering the following advantages: (1) Reduced Cost: Reduction in installation labor with fewer components, faster mounting, faster wiring. (2) Maximized Energy Production: Each AC Module operates at its maximum, reducing overall losses from shading, mismatch, or module downtime. (3) Increased Safety. Electrical and fire safety experts agree that AC Modules have significant benefits, with no energized wiring or live connections during installation, maintenance or emergency conditions. (4) Simplified PV for a Broader Group of Installers. Dramatic simplification of design and installation of a solar power system, enabling faster and more efficient delivery of the product into the market through well-established, mainstream channels. This makes solar more accessible to the public. (5) Broadened the Rooftop Market: AC Modules enable solar for many homes that have shading, split roofs, or obstructions. In addition, due to the smaller building block size of 200W vs. 1000W, homeowners with budget limitations can start small and add to their systems over time. Through this DOE program GreenRay developed the all-in-one AC Module system with an integrated PV Module and microinverter, custom residential mounting and performance monitoring. Development efforts took the product from its initial concept, through prototypes, to a commercial product sold and deployed in the residential market. This pilot deployment has demonstrated the technical effectiveness of the AC Module system in meeting the needs and solving the problems of the residential market. While more expensive than the traditional central inverter systems at the pilot scale, the economics of AC Modules become more and more

  5. Diffusive suppression of AC-Stark shifts in atomic magnetometers

    PubMed Central

    Sulai, I. A.; Wyllie, R.; Kauer, M.; Smetana, G. S.; Wakai, R. T.; Walker, T. G.

    2016-01-01

    In atomic magnetometers, the vector AC-Stark shift associated with circularly polarized light generates spatially varying effective magnetic fields, which limit the magnetometer response and serve as sources of noise. We describe a scheme whereby optically pumping a small subvolume of the magnetometer cell and relying on diffusion to transport polarized atoms allows a magnetometer to be operated with minimal sensitivity to the AC-Stark field. © 2013 Optical Society of America PMID:23503278

  6. Accelerator Production of {sup 225}Ac For Alpha-Immunotherapy

    SciTech Connect

    Weidner, J. W.; Nortier, F. M.; Bach, H. T.; John, K. D.; Couture, A.; Ullmann, J. L.; Fassbender, M. E.; Goff, G. S.; Taylor, W.; Valdez, F.; Wolfsberg, L. E.; Cisneros, M.; Dry, D.; Gallegos, M.; Gritzo, R.; Bitteker, L. J.; Wender, S.; Baty, R. S.

    2011-06-01

    {sup 225}Ac has tremendous potential for the treatment of metastatic cancer due to the four alpha-particles emitted during its decay to stable {sup 209}Bi. Additionally, it is one of the few alpha-emitters being considered for clinical trials. The anticipated {sup 225}Ac demand for these trials is expected to far exceed the annual worldwide supply of approximately 1,000 mCi/yr. Consequently, the DOE Office of Science has funded investigations into accelerator-based production of {sup 225}Ac. Existing {sup 232}Th(p,x){sup 225}Ac cross section data indicate that up to 480 mCi/day of {sup 225}Ac could be created by bombarding a thick target of natural thorium with 100 MeV protons at the Los Alamos Isotope Production Facility. To verify these predictions, experiments are underway at the Los Alamos Neutron Science Center to measure the {sup 232}Th(p,x){sup 225}Ac production cross sections for protons in the energy range 40-200 MeV, and at 800 MeV. For 800 MeV protons, preliminary results indicate that the {sup 225}Ac production cross section is 12.4{+-}0.6 mb and the {sup 225}Ra production cross section is 3.2{+-}0.2 mb. Moreover, preliminary results suggest that the {sup 227}Ac production cross section is 16{+-}1 mb. Experiments to measure these same cross sections at proton energies below 200 MeV are planned for the last half of calendar year 2010.

  7. Accelerator Production of 225Ac For Alpha-Immunotherapy

    NASA Astrophysics Data System (ADS)

    Weidner, J. W.; Nortier, F. M.; Bach, H. T.; John, K. D.; Couture, A.; Ullmann, J. L.; Fassbender, M. E.; Goff, G. S.; Taylor, W.; Valdez, F.; Wolfsberg, L. E.; Cisneros, M.; Dry, D.; Gallegos, M.; Gritzo, R.; Bitteker, L. J.; Wender, S.; Baty, R. S.

    2011-06-01

    225Ac has tremendous potential for the treatment of metastatic cancer due to the four alpha-particles emitted during its decay to stable 209Bi. Additionally, it is one of the few alpha-emitters being considered for clinical trials. The anticipated 225Ac demand for these trials is expected to far exceed the annual worldwide supply of approximately 1,000 mCi/yr. Consequently, the DOE Office of Science has funded investigations into accelerator-based production of 225Ac. Existing 232Th(p,x)225Ac cross section data indicate that up to 480 mCi/day of 225Ac could be created by bombarding a thick target of natural thorium with 100 MeV protons at the Los Alamos Isotope Production Facility. To verify these predictions, experiments are underway at the Los Alamos Neutron Science Center to measure the 232Th(p,x)225Ac production cross sections for protons in the energy range 40-200 MeV, and at 800 MeV. For 800 MeV protons, preliminary results indicate that the 225Ac production cross section is 12.4±0.6 mb and the 225Ra production cross section is 3.2±0.2 mb. Moreover, preliminary results suggest that the 227Ac production cross section is 16±1 mb. Experiments to measure these same cross sections at proton energies below 200 MeV are planned for the last half of calendar year 2010.

  8. Diagnostics of the Fermilab Tevatron using an AC dipole

    NASA Astrophysics Data System (ADS)

    Miyamoto, Ryoichi

    The Fermilab Tevatron is currently the world's highest energy colliding beam facility. Its counter-rotating proton and antiproton beams collide at 2 TeV center-of-mass. Delivery of such intense beam fluxes to experiments has required improved knowledge of the Tevatron's beam optical lattice. An oscillating dipole magnet, referred to as an AC dipole, is one of such a tool to non-destructively assess the optical properties of the synchrotron. We discusses development of an AC dipole system for the Tevatron, a fast-oscillating (f˜20 kHz) dipole magnet which can be adiabatically turned on and off to establish sustained coherent oscillations of the beam particles without affecting the transverse emittance. By utilizing an existing magnet and a higher power audio amplifier, the cost of the Tevatron AC dipole system became relatively inexpensive. We discuss corrections which must be applied to the driven oscillation measurements to obtain the proper interpretation of beam optical parameters from AC dipole studies. After successful operations of the Tevatron AC dipole system, AC dipole systems, similar to that in the Tevatron, will be build for the CERN LHC. We present several measurements of linear optical parameters (beta function and phase advance) for the Tevatron, as well as studies of non-linear perturbations from sextupole and octupole elements.

  9. AC electrophoretic deposition of organic-inorganic composite coatings.

    PubMed

    Yoshioka, T; Chávez-Valdez, A; Roether, J A; Schubert, D W; Boccaccini, A R

    2013-02-15

    Alternating current electrophoretic deposition (AC-EPD) of polyacrylic acid (PAA)-titanium oxide (TiO(2)) nanoparticle composites on stainless steel electrodes was investigated in basic aqueous solution. AC square wave with duty cycle of 80% was applied at a frequency of 1 kHz. FTIR-ATR spectra showed that both AC and direct current (DC) EPD successfully deposited PAA-TiO(2) composites. The deposition rate using AC-EPD was lower than that obtained in direct current DC-EPD. However, the microstructure and surface morphology of the deposited composite coatings were different depending on the type of electric field applied. AC-EPD applied for not more than 5 min led to smooth films without bubble formation, while DC-EPD for 1 min or more showed deposits with microstructural defects possibly as result of water electrolysis. AC-EPD was thus for the first time demonstrated to be a suitable technique to deposit organic-inorganic composite coatings from aqueous suspensions, showing that applying a square wave and frequency of 1 kHz leads to uniform PAA-TiO(2) composite coatings on conductive materials. PMID:23218240

  10. AC electrophoretic deposition of organic-inorganic composite coatings.

    PubMed

    Yoshioka, T; Chávez-Valdez, A; Roether, J A; Schubert, D W; Boccaccini, A R

    2013-02-15

    Alternating current electrophoretic deposition (AC-EPD) of polyacrylic acid (PAA)-titanium oxide (TiO(2)) nanoparticle composites on stainless steel electrodes was investigated in basic aqueous solution. AC square wave with duty cycle of 80% was applied at a frequency of 1 kHz. FTIR-ATR spectra showed that both AC and direct current (DC) EPD successfully deposited PAA-TiO(2) composites. The deposition rate using AC-EPD was lower than that obtained in direct current DC-EPD. However, the microstructure and surface morphology of the deposited composite coatings were different depending on the type of electric field applied. AC-EPD applied for not more than 5 min led to smooth films without bubble formation, while DC-EPD for 1 min or more showed deposits with microstructural defects possibly as result of water electrolysis. AC-EPD was thus for the first time demonstrated to be a suitable technique to deposit organic-inorganic composite coatings from aqueous suspensions, showing that applying a square wave and frequency of 1 kHz leads to uniform PAA-TiO(2) composite coatings on conductive materials.

  11. Update on bedside ultrasound (US) diagnosis of acute cholecystitis (AC).

    PubMed

    Zenobii, Maria Francesca; Accogli, Esterita; Domanico, Andrea; Arienti, Vincenzo

    2016-03-01

    Acute cholecystitis (AC) represents a principal cause of morbidity worldwide and is one of the most frequent reasons for hospitalization due to gastroenteric tract diseases. AC should be suspected in presence of clinical signs and of gallstones on an imaging study. Upper abdominal US represents the first diagnostic imaging step in the case of suspected AC. Computed tomography (CT) with intravenous contrast (IV) or magnetic resonance imaging (MRI) with gadolinium contrast and technetium hepatobiliary iminodiacetic acid (Tc-HIDA) can be employed to exclude complications. US examination should be performed with right subcostal oblique, with longitudinal and intercostal scans. Normal gallbladder US findings and AC major and minor US signs are described. Polyps, sludge and gallbladder wall thickening represent the more frequent pitfalls and they must be differentiated from stones, duodenal artifacts and many other non-inflammatory conditions that cause wall thickening, respectively. By means of bedside ultrasound, the finding of gallstones in combination with acute pain, when the clinician presses the gallbladder with the US probe (the sonographic Murphy's sign), has a 92.2 % positive predictive value for AC. In our preliminary experience, bedside US-performed by echoscopy (ES) and/or point-of-care US (POCUS) demonstrated good reliability in detecting signs of AC, and was always integrated with physical examination and performed by a skilled operator.

  12. Temperature integration at the AC thermosensory neurons in Drosophila.

    PubMed

    Tang, Xin; Platt, Michael D; Lagnese, Christopher M; Leslie, Jennifer R; Hamada, Fumika N

    2013-01-16

    Temperature sensation has a strong impact on animal behavior and is necessary for animals to avoid exposure to harmful temperatures. It is now well known that thermoTRP (transient receptor potential) channels in thermosensory neurons detect a variable range of temperature stimuli. However, little is known about how a range of temperature information is relayed and integrated in the neural circuits. Here, we show novel temperature integration between two warm inputs via Drosophila TRPA channels, TRPA1 and Pyrexia (Pyx). The internal AC (anterior cell) thermosensory neurons, which express TRPA1, detect warm temperatures and mediate temperature preference behavior. We found that the AC neurons were activated twice when subjected to increasing temperatures. The first response was at ∼25°C via TRPA1 channel, which is expressed in the AC neurons. The second response was at ∼27°C via the second antennal segments, indicating that the second antennal segments are involved in the detection of warm temperatures. Further analysis reveals that pyx-Gal4-expressing neurons have synapses on the AC neurons and that mutation of pyx eliminates the second response of the AC neurons. These data suggest that AC neurons integrate both their own TRPA1-dependent temperature responses and a Pyx-dependent temperature response from the second antennal segments. Our data reveal the first identification of temperature integration, which combines warm temperature information from peripheral to central neurons and provides the possibility that temperature integration is involved in the plasticity of behavioral outputs.

  13. Diagnostics of the Fermilab Tevatron using an AC dipole

    SciTech Connect

    Miyamoto, Ryoichi

    2008-08-01

    The Fermilab Tevatron is currently the world's highest energy colliding beam facility. Its counter-rotating proton and antiproton beams collide at 2 TeV center-of-mass. Delivery of such intense beam fluxes to experiments has required improved knowledge of the Tevatron's beam optical lattice. An oscillating dipole magnet, referred to as an AC dipole, is one of such a tool to non-destructively assess the optical properties of the synchrotron. We discusses development of an AC dipole system for the Tevatron, a fast-oscillating (f ~ 20 kHz) dipole magnet which can be adiabatically turned on and off to establish sustained coherent oscillations of the beam particles without affecting the transverse emittance. By utilizing an existing magnet and a higher power audio amplifier, the cost of the Tevatron AC dipole system became relatively inexpensive. We discuss corrections which must be applied to the driven oscillation measurements to obtain the proper interpretation of beam optical parameters from AC dipole studies. After successful operations of the Tevatron AC dipole system, AC dipole systems, similar to that in the Tevatron, will be build for the CERN LHC. We present several measurements of linear optical parameters (beta function and phase advance) for the Tevatron, as well as studies of non-linear perturbations from sextupole and octupole elements.

  14. Sequential control by speed drive for ac motor

    NASA Astrophysics Data System (ADS)

    Barsoum, Nader

    2012-11-01

    The speed drive for ac motor is widely used in the industrial field to allow direct control for the speed and torque without any feedback from the motor shaft. By using the ABB ACS800 speed drive unit, the speed and torque can be controlled using sequential control method. Sequential control is one of the application control method provided in the ABB ACS800 Drive, where a set of events or action performed in a particular order one after the other to control the speed and torque of the ac motor. It was claimed that sequential control method is using the preset seven constant speeds being provided in ABB ACS800 drive to control the speed and torque in a continuous and sequential manner. The characteristics and features of controlling the speed and torque using sequential control method can be investigated by observing the graphs and curves plotted which are obtained from the practical result. Sequential control can run either in the Direct Torque Control (DTC) or Scalar motor control mode. By using sequential control method, the ABB ACS800 drive can be programmed to run the motor automatically according to the time setting of the seven preset constant speeds. Besides, the intention of this project is to generate a new form of the experimental set up.

  15. Equivalent Electrical Circuit Representations of AC Quantized Hall Resistance Standards

    PubMed Central

    Cage, M. E.; Jeffery, A.; Matthews, J.

    1999-01-01

    We use equivalent electrical circuits to analyze the effects of large parasitic impedances existing in all sample probes on four-terminal-pair measurements of the ac quantized Hall resistance RH. The circuit components include the externally measurable parasitic capacitances, inductances, lead resistances, and leakage resistances of ac quantized Hall resistance standards, as well as components that represent the electrical characteristics of the quantum Hall effect device (QHE). Two kinds of electrical circuit connections to the QHE are described and considered: single-series “offset” and quadruple-series. (We eliminated other connections in earlier analyses because they did not provide the desired accuracy with all sample probe leads attached at the device.) Exact, but complicated, algebraic equations are derived for the currents and measured quantized Hall voltages for these two circuits. Only the quadruple-series connection circuit meets our desired goal of measuring RH for both ac and dc currents with a one-standard-deviation uncertainty of 10−8 RH or less during the same cool-down with all leads attached at the device. The single-series “offset” connection circuit meets our other desired goal of also measuring the longitudinal resistance Rx for both ac and dc currents during that same cool-down. We will use these predictions to apply small measurable corrections, and uncertainties of the corrections, to ac measurements of RH in order to realize an intrinsic ac quantized Hall resistance standard of 10−8 RH uncertainty or less.

  16. Three-phase ac-to-ac series-resonant power converter with a reduced number of thyristors

    SciTech Connect

    Klaassens, J.B.; de Beer, F. )

    1991-07-01

    This paper reports that ac-ac series-resonant converters have been proven to be functional and useful. Power pulse modulation with internal frequencies of tens of kHz and suited for multikilowatt power levels is applied to a series-resonant converter system for generating synthesized multiphase bipolar waveforms with reversible power flow and flow distortion. The use of a series-resonant circuit for power transfer and control obtains natural current commutation of the thyristors and the prevention of excessive stresses on components. Switches are required which have bidirectional current conduction and voltage blocking ability. The conventional series-resonant ac-ac converter applies a total for 24 anti-parallel thyristors. An alternative circuit configuration for the series-resonant ac-ac converter with only 12 thyristors is also presented. The alternative power circuit has three neutrals, related to the polyphase source, the load and the converter, which may be interconnected. If they are connected, the high-frequency component of the source and load currents will flow through the connection between the neutrals. The test results of a converter system generating three-phase sinusoidal input and output waveforms have demonstrated the significant aspects of this type of power interfaces.

  17. 21 CFR 880.6320 - AC-powered medical examination light.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false AC-powered medical examination light. 880.6320... Miscellaneous Devices § 880.6320 AC-powered medical examination light. (a) Identification. An AC-powered medical examination light is an AC-powered device intended for medical purposes that is used to illuminate...

  18. Apple MdACS6 Regulates Ethylene Biosynthesis During Fruit Development Involving Ethylene-Responsive Factor.

    PubMed

    Li, Tong; Tan, Dongmei; Liu, Zhi; Jiang, Zhongyu; Wei, Yun; Zhang, Lichao; Li, Xinyue; Yuan, Hui; Wang, Aide

    2015-10-01

    Ethylene biosynthesis in plants involves different 1-aminocyclopropane-1-carboxylic acid synthase (ACS) genes. The regulation of each ACS gene during fruit development is unclear. Here, we characterized another apple (Malus×domestica) ACS gene, MdACS6. The transcript of MdACS6 was observed not only in fruits but also in other tissues. During fruit development, MdACS6 was initiated at a much earlier stage, whereas MdACS3a and MdACS1 began to be expressed at 35 d before harvest and immediateley after harvest, respectively. Moreover, the enzyme activity of MdACS6 was significantly lower than that of MdACS3a and MdACS1, accounting for the low ethylene biosynthesis in young fruits. Overexpression of MdACS6 (MdACS6-OE) by transient assay in apple showed enhanced ethylene production, and MdACS3a was induced in MdACS6-OE fruits but not in control fruits. In MdACS6 apple fruits silenced by the virus-induced gene silencing (VIGS) system (MdACS6-AN), neither ethylene production nor MdACS3a transcript was detectable. In order to explore the mechanism through which MdACS3a was induced in MdACS6-OE fruits, we investigated the expression of apple ethylene-responsive factor (ERF) genes. The results showed that the expression of MdERF2 was induced in MdACS6-OE fruits and inhibited in MdACS6-AN fruits. Yeast one-hybrid assay showed that MdERF2 protein could bind to the promoter of MdACS3a. Moreover, down-regulation of MdERF2 in apple flesh callus led to a decrease of MdACS3a expression, demonstrating the regulation of MdERF2 on MdACS3a. The mechanism through which MdACS6 regulates the action of MdACS3a was discussed.

  19. Modelling ac ripple currents in HTS coated conductors

    NASA Astrophysics Data System (ADS)

    Xu, Zhihan; Grilli, Francesco

    2015-10-01

    Dc transmission using high temperature superconducting (HTS) coated conductors (CCs) offers a promising solution to the globally growing demand for effective, reliable and economic transmission of green energy up to the gigawatt level over very long distances. The credible estimation of the losses and thereby the heat dissipation involved, where ac ripples (introduced in rectification/ac-dc conversion) are viewed as a potential source of notable contribution, is highly essential for the rational design of practical HTS dc transmission cables and corresponding cryogenic systems to fulfil this demand. Here we report a targeted modelling study into the ac losses in a HTS CC subject to dc and ac ripple currents simultaneously, by solving Maxwell’s equations using the finite element method (FEM) in the commercial software package COMSOL. It is observed that the instantaneous loss exhibits only one peak per cycle in the HTS CC subject to sinusoidal ripples, given that the amplitude of the ac ripples is smaller than approximately 20% of that of the dc current. This is a distinct contrast to the usual observation of two peaks per cycle in a HTS CC subject to ac currents only. The unique mechanism is also revealed, which is directly associated with the finding that, around any local minima of the applied ac ripples, the critical state of -J c is never reached at the edges of the HTS CC, as it should be according to the Bean model. When running further into the longer term, it is discovered that the ac ripple loss of the HTS CC in full-wave rectification decays monotonically, at a speed which is found to be insensitive to the frequency of the applied ripples within our targeted situations, to a relatively low level of approximately 1.38 × 10-4 W m-1 in around 1.7 s. Comparison between this level and other typical loss contributions in a HTS dc cable implies that ac ripple currents in HTS CCs should only be considered as a minor source of dissipation in superconducting dc

  20. ac electroosmotic pumping induced by noncontact external electrodes.

    PubMed

    Wang, Shau-Chun; Chen, Hsiao-Ping; Chang, Hsueh-Chia

    2007-01-01

    Electroosmotic (EO) pumps based on dc electroosmosis is plagued by bubble generation and other electrochemical reactions at the electrodes at voltages beyond 1 V for electrolytes. These disadvantages limit their throughput and offset their portability advantage over mechanical syringe or pneumatic pumps. ac electroosmotic pumps at high frequency (>100 kHz) circumvent the bubble problem by inducing polarization and slip velocity on embedded electrodes,1 but they require complex electrode designs to produce a net flow. We report a new high-throughput ac EO pump design based on induced-polarization on the entire channel surface instead of just on the electrodes. Like dc EO pumps, our pump electrodes are outside of the load section and form a cm-long pump unit consisting of three circular reservoirs (3 mm in diameter) connected by a 1x1 mm channel. The field-induced polarization can produce an effective Zeta potential exceeding 1 V and an ac slip velocity estimated as 1 mmsec or higher, both one order of magnitude higher than earlier dc and ac pumps, giving rise to a maximum throughput of 1 mulsec. Polarization over the entire channel surface, quadratic scaling with respect to the field and high voltage at high frequency without electrode bubble generation are the reasons why the current pump is superior to earlier dc and ac EO pumps. PMID:19693362

  1. Muc5ac Mucin Expression During Rat Skin Development

    PubMed Central

    Ferretti, V.; Segal-Eiras, A.; Barbeito, C.G.; Croce, M.V.

    2015-01-01

    Some mucin genes have been detected during human embryonic and fetal organ development; however, little is known about mucin expression in epidermal development, neither in humans nor in other species. The present research was developed to explore Muc5ac skin expression during pre- and post-natal rat development. Immunohistochemistry (IHC), Western blotting (WB) and RT-PCR were employed. By IHC, Muc5ac protein was found early in embryonic epidermis from day 13 of gestation until seven days after birth when the surface epidermis became negative and the reaction was restricted to secreting sebum cells. In coincidence with IHC findings, WB analysis showed a band at approximately 200KDa at the same periods of development. Results were also confirmed by RT-PCR. Muc5ac expression in rat embryonic epidermis suggests that Muc5ac may play a protective role in embryonic skin previous to birth which may be replaced by pile covering. To our knowledge, this is the first report that confirmed Muc5ac expression during skin development. PMID:25820562

  2. AC propulsion system for an electric vehicle, phase 2

    NASA Technical Reports Server (NTRS)

    Slicker, J. M.

    1983-01-01

    A second-generation prototype ac propulsion system for a passenger electric vehicle was designed, fabricated, tested, installed in a modified Mercury Lynx vehicle and track tested at the Contractor's site. The system consisted of a Phase 2, 18.7 kw rated ac induction traction motor, a 192-volt, battery powered, pulse-width-modulated, transistorized inverter packaged for under rear seat installation, a 2-axis, 2-speed, automatically-shifted mechanical transaxle and a microprocessor-based powertrain/vehicle controller. A diagnostics computer to assist tuning and fault finding was fabricated. Dc-to-mechanical-system efficiency varied from 78% to 82% as axle speed/torque ranged from 159 rpm/788 nm to 65 rpm/328 nm. Track test efficiency results suggest that the ac system will be equal or superior to dc systems when driving urban cycles. Additional short-term work is being performed under a third contract phase (AC-3) to raise transaxle efficiency to predicted levels, and to improve starting and shifting characteristics. However, the long-term challenge to the system's viability remains inverter cost. A final report on the Phase 2 system, describing Phase 3 modifications, will be issued at the conclusion of AC-3.

  3. Impedance, AC conductivity and dielectric behavior Adeninium Trichloromercurate (II)

    NASA Astrophysics Data System (ADS)

    Fersi, M. Amine; Chaabane, I.; Gargouri, M.

    2016-09-01

    In this work, we report the measurements impedance spectroscopy technique for the organic-inorganic hybrid compound (C5H6N5) HgCl3, 11/2H2O measured in the 209 Hz-5 MHz frequency range from 378 to 428 K. Besides, the Cole-Cole (Z″ versus Z‧) plots were well fitted to an equivalent circuit built up by a parallel combination of resistance (R), fractal capacitance (CPE) and capacitance (C). Furthermore, the AC conductivity was investigated as a function of temperature and frequency in the same range. The experiment results indicated that AC conductivity (σac) was proportional to σdc + A ωS . The obtained results are discussed in terms of the correlated barrier hopping (CBH) model. An agreement between the experimental and theoretical results suggests that the AC conductivity behavior of Adeninium Trichloromercurate (II) can be successfully explained by CBH model. The contribution of single polaron hopping to AC conductivity in a present alloy was also studied.

  4. AC Loss Measurements on a 2G YBCO Coil

    SciTech Connect

    Rey, Christopher M; Duckworth, Robert C; Schwenterly, S W

    2011-01-01

    The Oak Ridge National Laboratory (ORNL) is collaborating with Waukesha Electric Systems (WES) to continue development of HTS power transformers. For compatibility with the existing power grid, a commercially viable HTS transformer will have to operate at high voltages in the range of 138 kV and above, and will have to withstand 550-kV impulse voltages as well. Second-generation (2G) YBCO coated conductors will be required for an economically-competitive design. In order to adequately size the refrigeration system for these transformers, the ac loss of these HTS coils must be characterized. Electrical AC loss measurements were conducted on a prototype high voltage (HV) coil with co-wound stainless steel at 60 Hz in a liquid nitrogen bath using a lock-in amplifier technique. The prototype HV coil consisted of 26 continuous (without splice) single pancake coils concentrically centered on a stainless steel former. For ac loss measurement purposes, voltage tap pairs were soldered across each set of two single pancake coils so that a total of 13 separate voltage measurements could be made across the entire length of the coil. AC loss measurements were taken as a function of ac excitation current. Results show that the loss is primarily concentrated at the ends of the coil where the operating fraction of critical current is the highest and show a distinct difference in current scaling of the losses between low current and high current regimes.

  5. Oxidative coupling of methane with ac and dc corona discharges

    SciTech Connect

    Liu, C.; Marafee, A.; Hill, B.; Xu, G.; Mallinson, R.; Lobban, L.

    1996-10-01

    The oxidative coupling of methane (OCM) is being actively studied for the production of higher hydrocarbons from natural gas. The present study concentrated on the oxidative conversion of methane in an atmospheric pressure, nonthermal plasma formed by ac or dc corona discharges. Methyl radicals are formed by reaction with negatively-charged oxygen species created in the corona discharge. The selectivity to products ethane and ethylene is affected by electrode polarity, frequency, and oxygen partial pressure in the feed. Higher C{sub 2} yields were obtained with the ac corona. All the ac corona discharges are initiated at room temperature (i.e., no oven or other heat source is used), and the temperature increases to 300--500 C due to the exothermic reactions and the discharge itself. The largest C{sub 2} yield is 21% with 43.3% methane conversion and 48.3% C{sub 2} selectivity at a flowrate of 100 cm{sup 3}/min when the ac corona is at 30 Hz, 5 kV (rms) input power was used. The methane conversion may be improved to more than 50% by increasing the residence time, but the C{sub 2} selectivity decreases. A reaction mechanism including the oxidative dehydrogenation (OXD) of ethane to ethylene is presented to explain the observed phenomena. The results suggest that ac and/or dc gas discharge techniques have significant promise for improving the economics of OCM processes.

  6. Aragonite coating solutions (ACS) based on artificial seawater

    NASA Astrophysics Data System (ADS)

    Tas, A. Cuneyt

    2015-03-01

    Aragonite (CaCO3, calcium carbonate) is an abundant biomaterial of marine life. It is the dominant inorganic phase of coral reefs, mollusc bivalve shells and the stalactites or stalagmites of geological sediments. Inorganic and initially precipitate-free aragonite coating solutions (ACS) of pH 7.4 were developed in this study to deposit monolayers of aragonite spherules or ooids on biomaterial (e.g., UHMWPE, ultrahigh molecular weight polyethylene) surfaces soaked in ACS at 30 °C. The ACS solutions of this study have been developed for the surface engineering of synthetic biomaterials. The abiotic ACS solutions, enriched with calcium and bicarbonate ions at different concentrations, essentially mimicked the artificial seawater composition and started to deposit aragonite after a long (4 h) incubation period at the tropical sea surface temperature of 30 °C. While numerous techniques for the solution deposition of calcium hydroxyapatite (Ca10(PO4)6(OH)2), of low thermodynamic solubility, on synthetic biomaterials have been demonstrated, procedures related to the solution-based surface deposition of high solubility aragonite remained uncommon. Monolayers of aragonite ooids deposited at 30 °C on UHMWPE substrates soaked in organic-free ACS solutions were found to possess nano-structures similar to the mortar-and-brick-type botryoids observed in biogenic marine shells. Samples were characterized using SEM, XRD, FTIR, ICP-AES and contact angle goniometry.

  7. Cadmium-induced ethylene production and responses in Arabidopsis thaliana rely on ACS2 and ACS6 gene expression

    PubMed Central

    2014-01-01

    Background Anthropogenic activities cause metal pollution worldwide. Plants can absorb and accumulate these metals through their root system, inducing stress as a result of excess metal concentrations inside the plant. Ethylene is a regulator of multiple plant processes, and is affected by many biotic and abiotic stresses. Increased ethylene levels have been observed after exposure to excess metals but it remains unclear how the increased ethylene levels are achieved at the molecular level. In this study, the effects of cadmium (Cd) exposure on the production of ethylene and its precursor 1-aminocyclopropane-1-carboxylic acid (ACC), and on the expression of the ACC Synthase (ACS) and ACC Oxidase (ACO) multigene families were investigated in Arabidopsis thaliana. Results Increased ethylene release after Cd exposure was directly measurable in a system using rockwool-cultivated plants; enhanced levels of the ethylene precursor ACC together with higher mRNA levels of ethylene responsive genes: ACO2, ETR2 and ERF1 also indicated increased ethylene production in hydroponic culture. Regarding underlying mechanisms, it was found that the transcript levels of ACO2 and ACO4, the most abundantly expressed members of the ACO multigene family, were increased upon Cd exposure. ACC synthesis is the rate-limiting step in ethylene biosynthesis, and transcript levels of both ACS2 and ACS6 showed the highest increase and became the most abundant isoforms after Cd exposure, suggesting their importance in the Cd-induced increase of ethylene production. Conclusions Cadmium induced the biosynthesis of ACC and ethylene in Arabidopsis thaliana plants mainly via the increased expression of ACS2 and ACS6. This was confirmed in the acs2-1acs6-1 double knockout mutants, which showed a decreased ethylene production, positively affecting leaf biomass and resulting in a delayed induction of ethylene responsive gene expressions without significant differences in Cd contents between wild-type and

  8. Thioesterification of 2-arylpropionic acids by recombinant acyl-coenzyme A synthetases (ACS1 and ACS2).

    PubMed

    Sevoz, C; Benoit, E; Buronfosse, T

    2000-04-01

    2-Arylpropionic acids are a class of frequently used nonsteroidal anti-inflammatory drugs exhibiting a potent inhibition of cyclooxygenase isoforms supported by the (+)S-enantiomer alone. Nevertheless, some of these compounds in the (-)R configuration may undergo extensive inversion of configuration to their antipode. The key molecular basis for this mechanism invokes the stereoselective formation of the coenzyme A (CoA) thioester of the 2-arylpropionic acid by long-chain acyl-CoA synthetases (ACSs). In this report, rat recombinant ACS1 and ACS2 enzymes, constitutively highly expressed in adult rat liver and brain, respectively, have been overproduced in Escherichia coli strains and purified to homogeneity to investigate the involvement of these enzymes in the thioesterification of fenoprofen and ibuprofen. Recombinant ACS1 efficiently catalyzed both nonsteroidal anti-inflammatory drugs with Michaelis-Menten parameters of K(M) = 1686 +/- 93 microM, V(max) = 353 +/- 45 nmol/min/mg protein for (-)R-ibuprofen and K(M) = 103 +/- 12 microM, V(max) = 267 +/- 10 nmol/min/mg protein for (-)R-fenoprofen, and exhibited a marked stereoselectivity in favor of the (-)R-enantiomer. Recombinant ACS2, a closely related sequence with ACS1, exhibited a lower enzymatic efficacy from 7- to 130-fold for (-)R-ibuprofen and (-)R-fenoprofen, respectively. On the basis of these findings and considering the level of tissue expression of the different long-chain ACSs, ACS1 appears to be the major enzyme involved in the first step of the chiral inversion of 2-arylpropionic acids. Nevertheless, the participation of other ACS isoforms of minor quantitative importance could not be excluded in the thioesterification of xenobiotics.

  9. Variable transposition of eight maize activator (ac) elements located on the short arm of chromosome 1.

    PubMed

    Sheridan, William F

    2011-09-01

    Eight Activator (Ac) transposable elements mapped to the maize chromosome arm 1S were assessed for Ac transposition rates. For each of the Ac stocks, plants homozygous for the single Ac element and the Ds reporter r1-sc:m3 on chromosome 10 were crossed as females by a homozygous r1-sc:m3 tester color-converted W22 line. The resulting ears produced mostly coarsely spotted kernels and a low frequency of either near-colorless fine-spotted kernels or nonspotted kernels. The relative frequency of these two types of near-colorless kernels differed among the eight Ac stocks. The extent to which increased Ac dosage results in nonspotted kernels may be Ac-specific. Although all of the Ac elements are in near-isogenic inbred W22 lines, they varied to a large extent in their transposition frequency. These differences might possibly result from structural differences among the Ac elements. Because one pair of Ac elements derived from Ac33 on chromosome arm 5S differed about 13-fold in transposition frequency and a second pair of Ac elements derived from Ac12 on chromosome arm 1S differed about 3-fold in transposition frequency, this is not a likely explanation for all eight Ac elements. The data presented here support the notion that the differences in transposition frequency of the eight Ac elements may be a reflection of variability in Ac transcription or accessibility of the transposase to the Ac element, resulting from differences in the chromatin environments wherein the Ac elements are located. This is the first report of variability in transposition rates among different Ac donor lines.

  10. Superconducting shielded core reactor with reduced AC losses

    DOEpatents

    Cha, Yung S.; Hull, John R.

    2006-04-04

    A superconducting shielded core reactor (SSCR) operates as a passive device for limiting excessive AC current in a circuit operating at a high power level under a fault condition such as shorting. The SSCR includes a ferromagnetic core which may be either closed or open (with an air gap) and extends into and through a superconducting tube or superconducting rings arranged in a stacked array. First and second series connected copper coils each disposed about a portion of the iron core are connected to the circuit to be protected and are respectively wound inside and outside of the superconducting tube or rings. A large impedance is inserted into the circuit by the core when the shielding capability of the superconducting arrangement is exceeded by the applied magnetic field generated by the two coils under a fault condition to limit the AC current in the circuit. The proposed SSCR also affords reduced AC loss compared to conventional SSCRs under continuous normal operation.

  11. Flux-motion related ac losses in high Tc superconductors

    NASA Astrophysics Data System (ADS)

    Chen, Q. Y.

    1993-03-01

    The ac losses of high-temperature superconductors in the flux-depinned mixed-state have been treated using the classical magnetic diffusion equation in conjunction with various models of flux-motion. With the imaginary part representing the ac losses, the field- and frequency-dependent ac susceptibilities were investigated. The imaginary component was found to obey a scaling rule with a characteristic frequency, estimated to be about 10 exp 5-10 exp 9 Hz, that depended on the sample size and normal state resistivity. This frequency range agrees with earlier experimental results, which could not be accounted for previously based upon the notion of thermally activated hopping of vortices. The frequency scaling behaviors using flux-creep and flux-flow models are presented.

  12. AC Conductivity Studies of Lithium Based Phospho Vanadate Glasses

    NASA Astrophysics Data System (ADS)

    Nagendra, K.; Babu, G. Satish; Reddy, C. Narayana; Gowda, Veeranna

    2011-07-01

    Glasses in the system xLi2SO4-20Li2O-(80-x) [80P2O5-20V2O5] (5⩾x⩾20 mol%) has been prepared by melt quenching method. Dc and ac conductivity has been studied over a wide range of frequency (10 Hz to 10 MHz) and temperature (298 K-523 K). The dc conductivity found to increase with increase of Li2SO4 concentration. The ac conductivities have been fitted to the Almond-West type single power law equation σ(ω) = σ(0)+Aωs where `s' is the power law exponent. The ac conductivity found to increase with increase of Li2SO4 concentration. An attempt is made to elucidate the enhancement of lithium ion conduction in phosphor-vanadate glasses by considering the expansion of network structure.

  13. Reliability of emergency ac power systems at nuclear power plants

    SciTech Connect

    Battle, R E; Campbell, D J

    1983-07-01

    Reliability of emergency onsite ac power systems at nuclear power plants has been questioned within the Nuclear Regulatory Commission (NRC) because of the number of diesel generator failures reported by nuclear plant licensees and the reactor core damage that could result from diesel failure during an emergency. This report contains the results of a reliability analysis of the onsite ac power system, and it uses the results of a separate analysis of offsite power systems to calculate the expected frequency of station blackout. Included is a design and operating experience review. Eighteen plants representative of typical onsite ac power systems and ten generic designs were selected to be modeled by fault trees. Operating experience data were collected from the NRC files and from nuclear plant licensee responses to a questionnaire sent out for this project.

  14. Theory of the ac spin-valve effect.

    PubMed

    Kochan, Denis; Gmitra, Martin; Fabian, Jaroslav

    2011-10-21

    The spin-valve complex magnetoimpedance of symmetric ferromagnet-normal-metal-ferromagnet junctions is investigated within the drift-diffusion (standard) model of spin injection. The ac magnetoresistance-the real part difference of the impedances of the parallel and antiparallel magnetization configurations-exhibits an overall damped oscillatory behavior, as an interplay of the diffusion and spin relaxation times. In wide junctions the ac magnetoresistance oscillates between positive and negative values, reflecting resonant amplification and depletion of the spin accumulation, while the line shape for thin tunnel junctions is predicted to be purely Lorentzian. The ac spin-valve effect could be a technique to extract spin transport and spin relaxation parameters in the absence of a magnetic field and for a fixed sample size. PMID:22107552

  15. Introducing high performance distributed logging service for ACS

    NASA Astrophysics Data System (ADS)

    Avarias, Jorge A.; López, Joao S.; Maureira, Cristián; Sommer, Heiko; Chiozzi, Gianluca

    2010-07-01

    The ALMA Common Software (ACS) is a software framework that provides the infrastructure for the Atacama Large Millimeter Array and other projects. ACS, based on CORBA, offers basic services and common design patterns for distributed software. Every properly built system needs to be able to log status and error information. Logging in a single computer scenario can be as easy as using fprintf statements. However, in a distributed system, it must provide a way to centralize all logging data in a single place without overloading the network nor complicating the applications. ACS provides a complete logging service infrastructure in which every log has an associated priority and timestamp, allowing filtering at different levels of the system (application, service and clients). Currently the ACS logging service uses an implementation of the CORBA Telecom Log Service in a customized way, using only a minimal subset of the features provided by the standard. The most relevant feature used by ACS is the ability to treat the logs as event data that gets distributed over the network in a publisher-subscriber paradigm. For this purpose the CORBA Notification Service, which is resource intensive, is used. On the other hand, the Data Distribution Service (DDS) provides an alternative standard for publisher-subscriber communication for real-time systems, offering better performance and featuring decentralized message processing. The current document describes how the new high performance logging service of ACS has been modeled and developed using DDS, replacing the Telecom Log Service. Benefits and drawbacks are analyzed. A benchmark is presented comparing the differences between the implementations.

  16. Modeling and Correcting the Time-Dependent ACS PSF

    NASA Technical Reports Server (NTRS)

    Rhodes, Jason; Massey, Richard; Albert, Justin; Taylor, James E.; Koekemoer, Anton M.; Leauthaud, Alexie

    2006-01-01

    The ability to accurately measure the shapes of faint objects in images taken with the Advanced Camera for Surveys (ACS) on the Hubble Space Telescope (HST) depends upon detailed knowledge of the Point Spread Function (PSF). We show that thermal fluctuations cause the PSF of the ACS Wide Field Camera (WFC) to vary over time. We describe a modified version of the TinyTim PSF modeling software to create artificial grids of stars across the ACS field of view at a range of telescope focus values. These models closely resemble the stars in real ACS images. Using 10 bright stars in a real image, we have been able to measure HST s apparent focus at the time of the exposure. TinyTim can then be used to model the PSF at any position on the ACS field of view. This obviates the need for images of dense stellar fields at different focus values, or interpolation between the few observed stars. We show that residual differences between our TinyTim models and real data are likely due to the effects of Charge Transfer Efficiency (CTE) degradation. Furthermore, we discuss stochastic noise that is added to the shape of point sources when distortion is removed, and we present MultiDrizzle parameters that are optimal for weak lensing science. Specifically, we find that reducing the MultiDrizzle output pixel scale and choosing a Gaussian kernel significantly stabilizes the resulting PSF after image combination, while still eliminating cosmic rays/bad pixels, and correcting the large geometric distortion in the ACS. We discuss future plans, which include more detailed study of the effects of CTE degradation on object shapes and releasing our TinyTim models to the astronomical community.

  17. Advanced Sensors for Accurate, Broadband AC Voltage Metrology

    NASA Astrophysics Data System (ADS)

    Lipe, Thomas E.; Kinard, Joseph R.; Novotny, Donald B.; Sims, June E.

    2013-06-01

    We report on advances in ac voltage metrology made possible by a new generation of Multijunction Thermal Converters (MJTCs). Although intended for use primarily in high-frequency (1 MHz to 100 MHz) metrology, their exceptional low-frequency qualities, combined with a large dynamic range, makes these MJTCs excellent devices for the frequency range 10 Hz to 100 MHz at voltages from 1 V to 20 V, depending on the design. We anticipate that these devices will form the future basis for ac voltage metrology at the National Institute of Standards and Technology (NIST).

  18. L’acétaminophène chez les enfants

    PubMed Central

    Goldman, Ran D.

    2013-01-01

    Résumé Question Je suggère fréquemment aux parents d’utiliser de l’acétaminophène comme traitement de la fièvre et de la douleur pour leurs enfants. J’ai récemment reçu un enfant à mon cabinet qui s’est présenté avec une éruption cutanée sous forme de lésions en cibles une journée après avoir pris de l’acétaminophène. L’éruption s’est résorbée 3 jours après qu’on ait arrêté l’administration d’acétaminophène. L’acétaminophène comporte-t-elle des risques d’événements indésirables comme celui-ci? Réponse Comme les autres médicaments ou substances actives, les préparations d’acétaminophène pourraient poser des risques d’événements indésirables. Au cours des dernières années, on a procédé à une investigation concernant une association potentielle entre l’acétaminophène et l’asthme et la Food and Drug Administration des États-Unis a récemment publié un avertissement à propos de réactions cutanées éventuelles, graves mais rares, associées à l’acétaminophène. Même si l’acétaminophène est principalement un médicament sûr, les professionnels de la santé devraient être alertes et informer les parents à propos de la possibilité d’événements indésirables rares mais sévères.

  19. Study of AC/RF properties of SRF ingot niobium

    SciTech Connect

    Dhakal, Pashupati; Tsindlekht, Menachem I; Genkin, Valery M; Ciovati, Gianluigi; Myneni, Ganapati Rao

    2013-09-01

    In an attempt to correlate the performance of superconducting radiofrequency cavities made of niobium with the superconducting properties, we present the results of the magnetization and ac susceptibility of the niobium used in the superconducting radiofrequency cavity fabrication. The samples were subjected to buffer chemical polishing (BCP) surface and high temperature heat treatments, typically applied to the cavities fabrications. The analysis of the results show the different surface and bulk ac conductivity for the samples subjected to BCP and heat treatment. Furthermore, the RF surface impedance is measured on the sample using a TE011 microwave cavity for a comparison to the low frequency measurements.

  20. Microfluidic pumping optimization in microgrooved channels with ac electrothermal actuations

    NASA Astrophysics Data System (ADS)

    Du, E.; Manoochehri, Souran

    2010-01-01

    An optimization methodology is developed and applied to an ac electrothermal pump design with patterned microgrooved features. The microgrooved configuration can overcome the restrictions of the conventional planar configuration on pumping performance by diminishing fast backward flows and suppressing prolonged streamlines. At all frequency excitations (0.2-1000 MHz) and ion concentration conditions (5×10-3-0.1 M), the optimum microgrooved configuration generates much faster flow rate than planar configuration. This happens without additional increases in the maximum temperature values. The effects of elevated temperature on ac ET flow behavior is investigated and analyzed.

  1. AC and Phase Sensing of Nanowires for Biosensing.

    PubMed

    Crescentini, Marco; Rossi, Michele; Ashburn, Peter; Lombardini, Marta; Sangiorgi, Enrico; Morgan, Hywel; Tartagni, Marco

    2016-04-19

    Silicon nanowires are label-free sensors that allow real-time measurements. They are economical and pave the road for point-of-care applications but require complex readout and skilled personnel. We propose a new model and technique for sensing nanowire sensors using alternating currents (AC) to capture both magnitude and phase information from the sensor. This approach combines the advantages of complex impedance spectroscopy with the noise reduction performances of lock-in techniques. Experimental results show how modifications of the sensors with different surface chemistries lead to the same direct-current (DC) response but can be discerned using the AC approach.

  2. AC Loss Analysis on the Superconducting Coupling Magnet in MICE

    SciTech Connect

    Wu, Hong; Wang, Li; Green, Michael; Li, LanKai; Xu, FengYu; Liu, XiaoKun; Jia, LinXinag

    2008-07-08

    A pair of coupling solenoids is used in MICE experiment to generate magnetic field which keeps the muons within the iris of thin RF cavity windows. The coupling solenoids have a 1.5-meter inner diameter and will produce 7.4 T peak magnetic field. Three types of AC losses in coupling solenoid are discussed. The affect of AC losses on the temperature distribution within the cold mass during charging and rapid discharging process is analyzed also. The analysis result will be further confirmed by the experiment of the prototype solenoid for coupling solenoid, which will be designed, fabricated and tested at ICST.

  3. The ac propulsion system for an electric vehicle, phase 1

    NASA Technical Reports Server (NTRS)

    Geppert, S.

    1981-01-01

    A functional prototype of an electric vehicle ac propulsion system was built consisting of a 18.65 kW rated ac induction traction motor, pulse width modulated (PWM) transistorized inverter, two speed mechanically shifted automatic transmission, and an overall drive/vehicle controller. Design developmental steps, and test results of individual components and the complex system on an instrumented test frame are described. Computer models were developed for the inverter, motor and a representative vehicle. A preliminary reliability model and failure modes effects analysis are given.

  4. Interplay between electron overheating and ac Josephson effect

    NASA Astrophysics Data System (ADS)

    De Cecco, A.; Le Calvez, K.; Sacépé, B.; Winkelmann, C. B.; Courtois, H.

    2016-05-01

    We study the response of high-critical-current proximity Josephson junctions to a microwave excitation. Electron overheating in such devices is known to create hysteretic dc voltage-current characteristics. Here we demonstrate that it also strongly influences the ac response. The interplay of electron overheating and ac Josephson dynamics is revealed by the evolution of the Shapiro steps with the microwave drive amplitude. Extending the resistively shunted Josephson junction model by including a thermal balance for the electronic bath coupled to phonons, a strong electron overheating is obtained.

  5. Trapping of Rb Atoms by ac Electric Fields

    SciTech Connect

    Schlunk, Sophie; Marian, Adela; Geng, Peter; Meijer, Gerard; Schoellkopf, Wieland; Mosk, Allard P.

    2007-06-01

    We demonstrate trapping of an ultracold gas of neutral atoms in a macroscopic ac electric trap. Three-dimensional confinement is obtained by switching between two saddle-point configurations of the electric field. Stable trapping is observed in a narrow range of switching frequencies around 60 Hz. The dynamic confinement of the atoms is directly visualized at different phases of the ac switching cycle. We observe about 10{sup 5} Rb atoms in the 1 mm{sup 3} large and several microkelvins deep trap with a lifetime of approximately 5 s.

  6. AC and Phase Sensing of Nanowires for Biosensing

    PubMed Central

    Crescentini, Marco; Rossi, Michele; Ashburn, Peter; Lombardini, Marta; Sangiorgi, Enrico; Morgan, Hywel; Tartagni, Marco

    2016-01-01

    Silicon nanowires are label-free sensors that allow real-time measurements. They are economical and pave the road for point-of-care applications but require complex readout and skilled personnel. We propose a new model and technique for sensing nanowire sensors using alternating currents (AC) to capture both magnitude and phase information from the sensor. This approach combines the advantages of complex impedance spectroscopy with the noise reduction performances of lock-in techniques. Experimental results show how modifications of the sensors with different surface chemistries lead to the same direct-current (DC) response but can be discerned using the AC approach. PMID:27104577

  7. Introducing AC inductive reactance with a power tool

    NASA Astrophysics Data System (ADS)

    Bryant, Wesley; Baker, Blane

    2016-09-01

    The concept of reactance in AC electrical circuits is often non-intuitive and difficult for students to grasp. In order to address this lack of conceptual understanding, classroom exercises compare the predicted resistance of a power tool, based on electrical specifications, to measured resistance. Once students discover that measured resistance is smaller than expected, they are asked to explain these observations using previously studied principles of magnetic induction. Exercises also introduce the notion of inductive reactance and impedance in AC circuits and, ultimately, determine self-inductance of the motor windings within the power tool.

  8. Dynamically tuned high-Q AC-dipole implementation

    SciTech Connect

    Oddo, P.; Bai, M.; Dawson, W.C.; Meng, W.; Mernick, K.; Pai, C.; Roser, T.; Russo, T.

    2010-05-02

    AC-dipole magnets are typically implemented as a parallel LC resonant circuit. To maximize efficiency, it's beneficial to operate at a high Q. This, however, limits the magnet to a narrow frequency range. Current designs therefore operate at a low Q to provide a wider bandwidth at the cost of efficiency. Dynamically tuning a high Q resonant circuit tries to maintain a high efficiency while providing a wide frequency range. The results of ongoing efforts at BNL to implement dynamically tuned high-Q AC dipoles will be presented.

  9. Interlayer thermal conductivity of rubrene measured by ac-calorimetry

    NASA Astrophysics Data System (ADS)

    Zhang, H.; Brill, J. W.

    2013-07-01

    We have measured the interlayer thermal conductivity of crystals of the organic semiconductor rubrene, using ac-calorimetry. Since ac-calorimetry is most commonly used for measurements of the heat capacity, we include a discussion of its extension for measurements of the transverse thermal conductivity of thin crystals of poor thermal conductors, including the limitations of the technique. For rubrene, we find that the interlayer thermal conductivity, ≈0.7 mW/cm . K, is several times smaller than the (previously measured) in-layer value, but its temperature dependence indicates that the interlayer mean free path is at least a few layers.

  10. System and method for determining stator winding resistance in an AC motor using motor drives

    DOEpatents

    Lu, Bin; Habetler, Thomas G; Zhang, Pinjia

    2013-02-26

    A system and method for determining the stator winding resistance of AC motors is provided. The system includes an AC motor drive having an input connectable to an AC source and an output connectable to an input terminal of an AC motor, a pulse width modulation (PWM) converter having switches therein to control current flow and terminal voltages in the AC motor, and a control system connected to the PWM converter. The control system generates a command signal to cause the PWM converter to control an output of the AC motor drive corresponding to an input to the AC motor, selectively generates a modified command signal to cause the PWM converter to inject a DC signal into the output of the AC motor drive, and determines a stator winding resistance of the AC motor based on the DC signal of at least one of the voltage and current.

  11. Encapsulation of α-Particle–Emitting 225Ac3+ Ions Within Carbon Nanotubes

    PubMed Central

    Matson, Michael L.; Villa, Carlos H.; Ananta, Jeyarama S.; Law, Justin J.; Scheinberg, David A.; Wilson, Lon J.

    2016-01-01

    225Ac3+ is a generator of α-particle–emitting radionuclides with 4 net α-particle decays that can be used therapeutically. Targeting 225Ac3+ by use of ligands conjugated to traditional bifunctional chelates limits the amount of 225Ac3+ that can be delivered. Ultrashort, single-walled carbon nanotubes (US-tubes), previously demonstrated as sequestering agents of trivalent lanthanide ions and small molecules, also successfully incorporate 225Ac3+. Methods Aqueous loading of both 225Ac3+ ions and Gd3+ ions via bath sonication was used to construct 225Ac@gadonanotubes (225Ac@GNTs). The 225Ac@GNTs were subsequently challenged with heat, time, and human serum. Results US-tubes internally loaded with both 225Ac3+ ions and Gd3+ ions show 2 distinct populations of 225Ac3+ ions: one rapidly lost in human serum and one that remains bound to the US-tubes despite additional challenge with heat, time, and serum. The presence of the latter population depended on cosequestration of Gd3+ and 225Ac3+ ions. Conclusion US-tubes successfully sequester 225Ac3+ ions in the presence of Gd3+ ions and retain them after a human serum challenge, rendering 225Ac@GNTs candidates for radioimmunotherapy for delivery of 225Ac3+ ions at higher concentrations than is currently possible for traditional ligand carriers. PMID:25931476

  12. UPS with input commutation between ac and dc sources of power

    SciTech Connect

    Severinsky, A.J.

    1993-08-31

    An uninterruptible power supply is described, said power supply comprising: AC input terminal means for receiving a first AC voltage from an AC power source; DC input terminal means for receiving a first DC voltage from a DC power source; AC output terminal means for connecting to a load; converter means for converting said first AC voltage to a second DC voltage across electrical charge storage means coupled to said converter means, said second DC voltage being larger than the maximum peak voltage of said first AC voltage and said first DC voltage; switching means coupled to said AC power source and said DC power source for selectively connecting said AC power source or said DC power source to said converter means; inverter means coupled to said electrical charge storage means for receiving said second DC voltage and inverting said second DC voltage to a second AC voltage, said second AC voltage being coupled to said AC output terminal means; and control means coupled to said switching means for controlling the operation of said switching means, said control means operating said switching means to connect said AC power source to said converter means only when said first AC voltage is within a predetermined range and operating to connect said DC power source to said converter means when said first AC voltage is outside of said range.

  13. Cloning of the Aegiceras corniculatum class I chitinase gene (AcCHI I) and the response of AcCHI I mRNA expression to cadmium stress.

    PubMed

    Wang, Li-Ying; Wang, You-Shao; Cheng, Hao; Zhang, Jing-Ping; Yeok, Foong Swee

    2015-10-01

    Chitinases in terrestrial plants have been reported these are involved in heavy metal tolerance/detoxification. This is the first attempt to reveal chitinase gene (AcCHI I) and its function on metal detoxification in mangroves Aegiceras corniculatum. RT-PCR and RACE techniques were used to clone AcCHI I, while real-time quantitative PCR was employed to assess AcCHI I mRNA expressions in response to Cadmium (Cd). The deduced AcCHI I protein consists of 316 amino acids, including a signal peptide region, a chitin-binding domain (CBD) and a catalytic domain. Protein homology modeling was performed to identify potential features in AcCHI I. The CBD structure of AcCHI I might be critical for metal tolerance/homeostasis of the plant. Clear tissue-specific differences in AcCHI I expression were detected, with higher transcript levels detected in leaves. Results demonstrated that a short duration of Cd exposure (e.g., 3 days) promoted AcCHI I expression in roots. Upregulated expression was also detected in leaves under 10 mg/kg Cd concentration stress. The present study demonstrates that AcCHI I may play an important role in Cd tolerance/homeostasis in the plant. Further studies of the AcCHI I protein, gene overexpression, the promoter and upstream regulation will be necessary for clarifying the functions of AcCHI I. PMID:26044931

  14. Cloning of the Aegiceras corniculatum class I chitinase gene (AcCHI I) and the response of AcCHI I mRNA expression to cadmium stress.

    PubMed

    Wang, Li-Ying; Wang, You-Shao; Cheng, Hao; Zhang, Jing-Ping; Yeok, Foong Swee

    2015-10-01

    Chitinases in terrestrial plants have been reported these are involved in heavy metal tolerance/detoxification. This is the first attempt to reveal chitinase gene (AcCHI I) and its function on metal detoxification in mangroves Aegiceras corniculatum. RT-PCR and RACE techniques were used to clone AcCHI I, while real-time quantitative PCR was employed to assess AcCHI I mRNA expressions in response to Cadmium (Cd). The deduced AcCHI I protein consists of 316 amino acids, including a signal peptide region, a chitin-binding domain (CBD) and a catalytic domain. Protein homology modeling was performed to identify potential features in AcCHI I. The CBD structure of AcCHI I might be critical for metal tolerance/homeostasis of the plant. Clear tissue-specific differences in AcCHI I expression were detected, with higher transcript levels detected in leaves. Results demonstrated that a short duration of Cd exposure (e.g., 3 days) promoted AcCHI I expression in roots. Upregulated expression was also detected in leaves under 10 mg/kg Cd concentration stress. The present study demonstrates that AcCHI I may play an important role in Cd tolerance/homeostasis in the plant. Further studies of the AcCHI I protein, gene overexpression, the promoter and upstream regulation will be necessary for clarifying the functions of AcCHI I.

  15. BOLD signal effects of transcranial alternating current stimulation (tACS) in the alpha range: A concurrent tACS-fMRI study.

    PubMed

    Vosskuhl, Johannes; Huster, René J; Herrmann, Christoph S

    2016-10-15

    Many studies have proven transcranial alternating current stimulation (tACS) to manipulate brain activity. Until now it is not known, however, how these manipulations in brain activity are represented in brain metabolism or how spatially specific these changes are. Alpha-tACS has been shown to enhance the amplitude of the individual alpha frequency (IAF) and a negative correlation between alpha amplitude and occipital BOLD signal was reported in numerous EEG/fMRI experiments. Thus, alpha-tACS was chosen to test the effects of tACS on the BOLD signal. A reduction thereof was expected during alpha-tACS which shows the spatial extent of tACS effects beyond modeling studies. Three groups of subjects were measured in an MRI scanner, receiving tACS at either their IAF (N=11), 1Hz (control; N=12) or sham (i.e., no stimulation - a second control; N=11) while responding to a visual vigilance task. Stimulation was administered in an interleaved pattern of tACS-on runs and tACS-free baseline periods. The BOLD signal was analyzed in response to tACS-onset during resting state and in response to seldom target stimuli. Alpha-tACS at 1.0mA reduced the task-related BOLD response to visual targets in the occipital cortex as compared to tACS-free baseline periods. The deactivation was strongest in an area where the BOLD signal was shown to correlate negatively with alpha amplitude. A direct effect of tACS on resting state BOLD signal levels could not be shown. Our findings suggest that tACS-related changes in BOLD activity occur only as a modulation of an existing BOLD response.

  16. Perceptions of breath alcohol concentration (BrAC) levels among a sample of bar patrons with BrAC values of 0.08% or higher.

    PubMed

    Martin, Ryan J; Chaney, Beth H; Cremeens-Matthews, Jennifer; Vail-Smith, Karen

    2016-09-01

    Breath alcohol concentration (BrAC) is a commonly used measure of alcohol intoxication. Because of the potential negative consequences of excessive alcohol consumption, it is important to examine how accurately intoxicated individuals can estimate their BrAC values, especially individuals over the legal BrAC driving threshold (i.e., 0.08%). To better understand perceptions of BrAC values among intoxicated individuals, this field study examined actual BrAC values and BrAC range estimates (0.08% and above, 0.02-0.07%, less than 0.02%) among a sample of bar patrons (N = 454) with BrAC levels at 0.08% or higher. Bivariate and multivariate analyses were conducted to examine the relationship between actual BrAC values and perceived BrAC levels. We also examined whether the following demographic and drinking variables were associated with underestimating BrAC in this sample: gender, age, race, college student status, plans to get home, and hazardous drinking. Results indicated that the majority (60.4%) of participants underestimated their BrAC (i.e., less than 0.08%) and lower BrAC values correlated with underestimating BrAC ranges (p < .001, 95% CI[0.2, 0.6]). Further, females (p = .001, 95% CI[1.3, 3.3]) and participants under 21 (p = .039, 95% CI = 1.0, 2.6) were significantly more likely to estimate their BrAC to be less than 0.08%, which is concerning given that young (less than 21) intoxicated females are a group at high risk for sexual assault on college campuses. (PsycINFO Database Record PMID:27631614

  17. 78 FR 42567 - ACS Wireless, Inc.; Notice of Application

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-16

    ... From the Federal Register Online via the Government Publishing Office SECURITIES AND EXCHANGE COMMISSION ACS Wireless, Inc.; Notice of Application June 25, 2013. Correction In notice document 2013-15658 beginning on page 39345 in the issue of Monday, July 1, 2013, make the following correction: On page...

  18. Introducing AC Inductive Reactance with a Power Tool

    ERIC Educational Resources Information Center

    Bryant, Wesley; Baker, Blane

    2016-01-01

    The concept of reactance in AC electrical circuits is often non-intuitive and difficult for students to grasp. In order to address this lack of conceptual understanding, classroom exercises compare the predicted resistance of a power tool, based on electrical specifications, to measured resistance. Once students discover that measured resistance…

  19. An overview of the ALMA Common Software (ACS) .

    NASA Astrophysics Data System (ADS)

    Di Marcantonio, P.; Cirami, R.; Caproni, A.; Chiozzi, G.; Jeram, B.; Sommer, H.; Harrington, S.; Zagar, K.; Plesko, M.; Sekoranja, M.

    The ALMA Common Software (ACS) is an application framework designed to provide a common and homogeneous software architecture and infrastructure, spanning the end to end needs of an Astronomical observatory, from the Telescope Control system to high-level data flow management. ACS offers, at the lower level, several basic services needed for object-oriented distributed computing like transparent remote object invocation, object deployment and location, distributed error, alarm handling, logging and events. On top of this it provides an application architecture based on the Component/Container paradigm that fosters sharing and reusing of software components. Although developed for the ALMA project, ACS is now used by several other projects worldwide, among which the Italian Sardinia Radio Telescope (SRT). Besides, there is an active community that shares ideas, concepts and actual software components. Major drivers for this diffusion were the choice of adopting the LGPL public license and the adoption of CORBA, a free but reliable and widely used middleware software. In this paper we present an overview of the main features of ACS, emphasizing in particular the role of INAF-OAT in this project.

  20. Container-component model and XML in ALMA ACS

    NASA Astrophysics Data System (ADS)

    Sommer, Heiko; Chiozzi, Gianluca; Zagar, Klemen; Voelter, Markus

    2004-09-01

    ALMA software, from high-level data flow applications down to instrument control, is built using the ACS framework. To meet the challenges of developing distributed software in distributed teams, ACS offers a container/component model that integrates the use of XML transfer objects. ACS containers are built on top of CORBA and are available for C++, Java, and Python, so that ALMA software can be written as components in any of these languages. The containers perform technical aspects of the software system, while components can focus on the implementation of functional requirements. Like Web services, components can use XML to exchange structured data by value. For Java components, the container seamlessly integrates the use of XML binding classes, which are Java classes that encapsulate access to XML data through type-safe methods. Binding classes are generated from XML schemas, allowing the Java compiler to enforce compliance of application code with the XML schemas. This presentation will explain the capabilities of the ACS container/component model, and how it relates to other middleware technologies that are popular in industry.

  1. Measurement of the 225Ac half-life.

    PubMed

    Pommé, S; Marouli, M; Suliman, G; Dikmen, H; Van Ammel, R; Jobbágy, V; Dirican, A; Stroh, H; Paepen, J; Bruchertseifer, F; Apostolidis, C; Morgenstern, A

    2012-11-01

    The (225)Ac half-life was determined by measuring the activity of (225)Ac sources as a function of time, using various detection techniques: α-particle counting with a planar silicon detector at a defined small solid angle and in a nearly-2π geometry, 4πα+β counting with a windowless CsI sandwich spectrometer and with a pressurised proportional counter, gamma-ray spectrometry with a HPGe detector and with a NaI(Tl) well detector. Depending on the technique, the decay was followed for 59-141 d, which is about 6-14 times the (225)Ac half-life. The six measurement results were in good mutual agreement and their mean value is T(1/2)((225)Ac)=9.920 (3)d. This half-life value is more precise and better documented than the currently recommended value of 10.0 d, based on two old measurements lacking uncertainty evaluations.

  2. Regenerating /sup 227/Ac from highly contaminated preparations

    SciTech Connect

    Volynskii, L.D.; Garbuzov, V.M.; Tsirlin, V.A.

    1988-05-01

    Studies have been made on the conditions for coprecipitation of actinium with calcium, barium, and iron fluorides, as well as on the conditions for the selective separation of actinium and iron on a cation-exchange material by the use of hydrochloric acid in acetone. Several ways of regenerating /sup 337/Ac from highly contaminated preparations are proposed.

  3. DESIGN OF AN AC-DIPOLE FOR USE IN RHIC.

    SciTech Connect

    PARKER,B.; BAI,M.; JAIN,A.; MCINTYRE,G.; METH,M.; PEGGS,S.; ROSER,T.; SANDERS,R.; TRBOJEVIC,D.

    1999-03-29

    We present two options for implementing a pair of AC-dipoles in RHIC for spin flipping, measuring linear optical functions and nonlinear diagnostics. AC-dipoles are magnets that can be adiabatically excited and de-excited with a continuous sine-wave in order to coherently move circulating beam out to large betatron amplitudes without incurring emittance blow up [1]. The AGS already uses a similar device for getting polarized proton beams through depolarizing resonances [2]. By placing the magnets in the IP4 common beam region, two AC-dipoles are sufficient to excite both horizontal and vertical motion in both RHIC rings. While we initially investigated an iron-dominated magnet design using available steel tape cores; we now favor a new air coil plus ferrite design featuring mechanical frequency tuning, in order to best match available resources to demanding frequency sweeping requirements. Both magnet designs are presented here along with model magnet test results. The challenge is to make AC-dipoles available for year 2000 RHIC running.

  4. High-power ac/dc variable load simulator

    NASA Technical Reports Server (NTRS)

    Joncas, K. P.; Birnbach, S.; Bruce, L. D.; Smith, L.

    1975-01-01

    Design of medium-power dynamic electrical load simulator has been extended to permit simulation of ac as well as dc loads and to provide for operation at higher power levels. Simulator is internally protected against reverse voltage, overvoltage, overcurrent, and overload conditions.

  5. Measurement of the 225Ac half-life.

    PubMed

    Pommé, S; Marouli, M; Suliman, G; Dikmen, H; Van Ammel, R; Jobbágy, V; Dirican, A; Stroh, H; Paepen, J; Bruchertseifer, F; Apostolidis, C; Morgenstern, A

    2012-11-01

    The (225)Ac half-life was determined by measuring the activity of (225)Ac sources as a function of time, using various detection techniques: α-particle counting with a planar silicon detector at a defined small solid angle and in a nearly-2π geometry, 4πα+β counting with a windowless CsI sandwich spectrometer and with a pressurised proportional counter, gamma-ray spectrometry with a HPGe detector and with a NaI(Tl) well detector. Depending on the technique, the decay was followed for 59-141 d, which is about 6-14 times the (225)Ac half-life. The six measurement results were in good mutual agreement and their mean value is T(1/2)((225)Ac)=9.920 (3)d. This half-life value is more precise and better documented than the currently recommended value of 10.0 d, based on two old measurements lacking uncertainty evaluations. PMID:22940415

  6. Pairing fluctuation ac conductivity of disordered thin films

    NASA Astrophysics Data System (ADS)

    Petković, Aleksandra; Vinokur, Valerii M.

    2013-09-01

    We study temperature T and frequency ω dependence of the in-plane fluctuation conductivity of a disordered superconducting film above the critical temperature. Our calculation is based on the nonlinear sigma model within the Keldysh technique. The fluctuation contributions of different physical origin are found and analyzed in a wide frequency range. In the low-frequency range, ω ≪ T, we reproduce the known leading terms and find additional subleading ones in the Aslamazov-Larkin and the Maki-Thompson contributions to the ac conductivity. We also calculate the density of states ac correction. In the dc case these contributions logarithmically depend on the Ginzburg-Landau rate and are considerably smaller that the leading ones. However, in the ac case an external finite-frequency electromagnetic field strongly suppresses the known Aslamazov-Larkin and Maki-Thompson ac contributions, while the corresponding new terms and the density of states contribution are weakly suppressed and therefore become relevant at finite frequencies.

  7. 14. VIEW OF AIR COMPRESSOR. 1500 kw Westinghouse AC generator ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. VIEW OF AIR COMPRESSOR. 1500 kw Westinghouse AC generator steam-turbine unit; beyond is air compressor of Chicago Pneumatic Tool Company, 1920, engineered by Earl E. Know Company, Erie, Pennsylvania. - Juniata Shops, Power Plant & Boiler House, East of Fourth Avenue at Second Street, Altoona, Blair County, PA

  8. Equivalent Circuits For AC-Impedance Analysis Of Corrosion

    NASA Technical Reports Server (NTRS)

    Danford, M. D.

    1992-01-01

    Report presents investigation of equivalent circuits for ac-impedance analysis of corrosion. Impedance between specimen and electrolyte measured as function of frequency. Data used to characterize corrosion electrochemical system in terms of equivalent circuit. Eleven resistor/capacitor equivalent-circuit models were analyzed.

  9. Direct Experimental Observation of a Practical AC Zeeman Force

    NASA Astrophysics Data System (ADS)

    Fancher, Charles; Pyle, Andrew; Rotunno, Andrew; Du, Shuangli; Aubin, Seth

    2016-05-01

    We present measurements of the spin-dependent AC Zeeman force produced by microwave magnetic near-field gradients on an atom chip. We measure the AC Zeeman force on ultracold 87 Rb atoms by observing its effect on the motion of atoms in free-fall and on those confined in a trap. We have studied the force as a function of microwave frequency detuning from a hyperfine transition at 6.8 GHz at several magnetic field strengths and have observed its characteristic bipolar and resonant features predicted by two-level dressed atom theory. We find that the force is several times the strength of gravity in our setup, and that it can be targeted to a specific hyperfine transition while leaving other hyperfine states and transitions relatively unaffected. We find that our measurements are reasonably consistent with theory and are working towards a parameter-free comparison. AC Zeeman potentials offer the possibility of targeting qualitatively different trapping potentials to different spin states, a capability currently absent from the toolbox of atomic quantum control techniques. In particular, an AC Zeeman potential could be used as the beamsplitter for a spin-dependent atom interferometer or for engineering a quantum gate. Work supported by AFOSR and W&M, and in part by AFRL.

  10. 23. AC GENERATOR, ALLISCHALMERS SN #1246797, MFG. MILWAUKEE, KW 1600 ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    23. AC GENERATOR, ALLIS-CHALMERS SN #1246797, MFG. MILWAUKEE, KW 1600 PF 80 C/O VOLTS 2300 AMPS 503 CY 60 PH 3 RMP 164 EXC VOLTS 125 AMPS MAN 300 - Columbia Canal & Power Plant, Waterfront of Broad River, Columbia, Richland County, SC

  11. Power factor control system for AC induction motors

    NASA Technical Reports Server (NTRS)

    Nola, F. J. (Inventor)

    1977-01-01

    A power factor control system for use with ac induction motors was designed which samples lines voltage and current through the motor and decreases power input to the motor proportional to the detected phase displacement between current and voltage. This system provides, less power to the motor, as it is less loaded.

  12. Context based computational analysis and characterization of ARS consensus sequences (ACS) of Saccharomyces cerevisiae genome.

    PubMed

    Singh, Vinod Kumar; Krishnamachari, Annangarachari

    2016-09-01

    Genome-wide experimental studies in Saccharomyces cerevisiae reveal that autonomous replicating sequence (ARS) requires an essential consensus sequence (ACS) for replication activity. Computational studies identified thousands of ACS like patterns in the genome. However, only a few hundreds of these sites act as replicating sites and the rest are considered as dormant or evolving sites. In a bid to understand the sequence makeup of replication sites, a content and context-based analysis was performed on a set of replicating ACS sequences that binds to origin-recognition complex (ORC) denoted as ORC-ACS and non-replicating ACS sequences (nrACS), that are not bound by ORC. In this study, DNA properties such as base composition, correlation, sequence dependent thermodynamic and DNA structural profiles, and their positions have been considered for characterizing ORC-ACS and nrACS. Analysis reveals that ORC-ACS depict marked differences in nucleotide composition and context features in its vicinity compared to nrACS. Interestingly, an A-rich motif was also discovered in ORC-ACS sequences within its nucleosome-free region. Profound changes in the conformational features, such as DNA helical twist, inclination angle and stacking energy between ORC-ACS and nrACS were observed. Distribution of ACS motifs in the non-coding segments points to the locations of ORC-ACS which are found far away from the adjacent gene start position compared to nrACS thereby enabling an accessible environment for ORC-proteins. Our attempt is novel in considering the contextual view of ACS and its flanking region along with nucleosome positioning in the S. cerevisiae genome and may be useful for any computational prediction scheme. PMID:27508123

  13. Biocontrol activity of Paenibacillus polymyxa AC-1 against Pseudomonas syringae and its interaction with Arabidopsis thaliana.

    PubMed

    Hong, Chi Eun; Kwon, Suk Yoon; Park, Jeong Mee

    2016-04-01

    Paenibacillus polymyxa AC-1 (AC-1) is a plant growth-promoting rhizobacterium (PGPR) that has been used as a soil inoculant for biocontrol of plant pathogenic fungi and to promote plant growth. In this study, we examine the effects of AC-1 on the bacterial phytopathogen Pseudomonas syringae and internal colonization of AC-1 by counting bacterial populations that colonize plants. AC-1 inhibited the growth of both P. syringae pv. tomato DC3000 (Pst) and P. syringae pv. tabaci (Pta) in a concentration-dependent manner in in vitro assays. Upon treatment of AC-1 dropping at root tip of axenically grown Arabidopsis, we found that most of the AC-1 was detected in interior of leaves of Arabidiopsis plants rather than roots after 5 days post infection, indicating systemic spreading of AC-1 occur. We examined further AC-1 colonization patterns in Arabidopsis mutants deficient in phytohormone signaling pathways. These results indicated that abscisic acid (ABA) and jasmonic acid (JA) signaling pathways positively and negatively contributed, respectively, to AC-1 colonization of leaves, whereas epiphytic accumulation of AC-1 around root tissues was not affected. This study shows that AC-1 is an effective biocontrol agent to suppress P. syringae growth, possibly owing to its colonization patterns as a leaf-inhabiting endophyte. The results showed in this work will help to expand our understanding of the mode of action of AC-1 as a biological control agent and consequently, its application in agriculture.

  14. Autographa californica multiple nucleopolyhedrovirus gene ac81 is required for nucleocapsid envelopment.

    PubMed

    Dong, Fang; Wang, Jinwen; Deng, Riqiang; Wang, Xunzhang

    2016-08-01

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) is a highly pathogenic Baculoviridae that targets insects, whose core gene, ac81, has an unknown function. To determine the role of ac81 in the life cycle of AcMNPV, an ac81-knockout (Ac-81KO-GP) was constructed through homologous recombination in Escherichia coli. We determined that no budded virions were produced in Ac-81KO-GP-transfected Sf9 cells, while there was no effect on viral DNA replication. Electron microscopy (EM) analysis revealed that occlusion-derived virions (ODVs) envelopment and the subsequent embedding of virions into occlusion bodies (OBs) were aborted due to ac81 deletion. Interestingly, confocal microscopy and immunofluorescence analysis revealed that Ac81 was predominantly localized to the ring zone of nuclei during the late phase of infection. In addition, Ac81 was localized to the mature and premature ODVs in virus-infected cells within the ring zone as revealed by immuno-electron microscopy (IEM) analysis. Furthermore, we determined that Ac81 contained a functional hydrophobic transmembrane (TM) domain, whose deletion resulted in a phenotype similar to that of Ac-81KO-GP. These results suggest that Ac81 might be a TM protein that played an important role in nucleocapsid envelopment. PMID:27212683

  15. Abscisic Acid Antagonizes Ethylene Production through the ABI4-Mediated Transcriptional Repression of ACS4 and ACS8 in Arabidopsis.

    PubMed

    Dong, Zhijun; Yu, Yanwen; Li, Shenghui; Wang, Juan; Tang, Saijun; Huang, Rongfeng

    2016-01-01

    Increasing evidence has revealed that abscisic acid (ABA) negatively modulates ethylene biosynthesis, although the underlying mechanism remains unclear. To identify the factors involved, we conducted a screen for ABA-insensitive mutants with altered ethylene production in Arabidopsis. A dominant allele of ABI4, abi4-152, which produces a putative protein with a 16-amino-acid truncation at the C-terminus of ABI4, reduces ethylene production. By contrast, two recessive knockout alleles of ABI4, abi4-102 and abi4-103, result in increased ethylene evolution, indicating that ABI4 negatively regulates ethylene production. Further analyses showed that expression of the ethylene biosynthesis genes ACS4, ACS8, and ACO2 was significantly decreased in abi4-152 but increased in the knockout mutants, with partial dependence on ABA. Chromatin immunoprecipitation-quantitative PCR assays showed that ABI4 directly binds the promoters of these ethylene biosynthesis genes and that ABA enhances this interaction. A fusion protein containing the truncated ABI4-152 peptide accumulated to higher levels than its full-length counterpart in transgenic plants, suggesting that ABI4 is destabilized by its C terminus. Therefore, our results demonstrate that ABA negatively regulates ethylene production through ABI4-mediated transcriptional repression of the ethylene biosynthesis genes ACS4 and ACS8 in Arabidopsis.

  16. Expression characteristics of CS-ACS1, CS-ACS2 and CS-ACS3, three members of the 1-aminocyclopropane-1-carboxylate synthase gene family in cucumber (Cucumis sativus L.) fruit under carbon dioxide stress.

    PubMed

    Mathooko, F M; Mwaniki, M W; Nakatsuka, A; Shiomi, S; Kubo, Y; Inaba, A; Nakamura, R

    1999-02-01

    We investigated the expression pattern of three 1-aminocyclopropane-1-carboxylate (ACC) synthase genes, CS-ACS1, CS-ACS2 and CS-ACS3 in cucumber (Cucumis sativus L.) fruit under CO2 stress. CO2 stress-induced ethylene production paralleled the accumulation of only CS-ACS1 transcripts which disappeared upon withdrawal of CO2. Cycloheximide inhibited the CO2 stress-induced ethylene production but superinduced the accumulation of CS-ACS1 transcript. At higher concentrations, cycloheximide also induced the accumulation of CS-ACS2 and CS-ACS3 transcripts. In the presence of CO2 and cycloheximide, the accumulation of CS-ACS2 transcript occurred within 1 h, disappeared after 3 h and increased greatly upon withdrawal of CO2. Inhibitors of protein kinase and types 1 and 2A protein phosphatases which inhibited and stimulated, respectively, CO2 stress-induced ethylene production had little effect on the expression of these genes. The results presented here identify CS-ACS1 as the main ACC synthase gene responsible for the increased ethylene biosynthesis in cucumber fruit under CO2 stress and suggest that this gene is a primary response gene and its expression is under negative control since it is expressed by treatment with cycloheximide. The results further suggest that the regulation of CO2 stress-induced ethylene biosynthesis by reversible protein phosphorylation does not result from enhanced ACC synthase transcription. PMID:10202812

  17. Recent applications of AC electrokinetics in biomolecular analysis on microfluidic devices.

    PubMed

    Sasaki, Naoki

    2012-01-01

    AC electrokinetics is a generic term that refers to an induced motion of particles and fluids under nonuniform AC electric fields. The AC electric fields are formed by application of AC voltages to microelectrodes, which can be easily integrated into microfluidic devices by standard microfabrication techniques. Moreover, the magnitude of the motion is large enough to control the mass transfer on the devices. These advantages are attractive for biomolecular analysis on the microfluidic devices, in which the characteristics of small space and microfluidics have been mainly employed. In this review, I describe recent applications of AC electrokinetics in biomolecular analysis on microfluidic devices. The applications include fluid pumping and mixing by AC electrokinetic flow, and manipulation of biomolecules such as DNA and proteins by various AC electrokinetic techniques. Future prospects for highly functional biomolecular analysis on microfluidic devices with the aid of AC electrokinetics are also discussed.

  18. Autographa californica multiple nucleopolyhedrovirus ac53 plays a role in nucleocapsid assembly

    SciTech Connect

    Liu Chao; Li Zhaofei Wu Wenbi; Li Lingling; Yuan Meijin; Pan Lijing; Yang Kai Pang Yi

    2008-12-05

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) orf53 (ac53) is a highly conserved gene existing in all sequenced Lepidoptera and Hymenoptera baculoviruses, but its function remains unknown. To investigate its role in the baculovirus life cycle, an ac53 deletion virus (vAc{sup ac53KO-PH-GFP}) was generated through homologous recombination in Escherichia coli. Fluorescence and light microscopy and titration analysis revealed that vAc{sup ac53KO-PH-GFP} could not produce infectious budded virus in infected Sf9 cells. Real-time PCR demonstrated that the ac53 deletion did not affect the levels of viral DNA replication. Electron microscopy showed that many lucent tubular shells devoid of the nucleoprotein core are present in the virogenic stroma and ring zone, indicating that the ac53 knockout affected nucleocapsid assembly. With a recombinant virus expressing an Ac53-GFP fusion protein, we observed that Ac53 was distributed within the cytoplasm and nucleus at 24 h post-infection, but afterwards accumulated predominantly near the nucleus-cytoplasm boundary. These data demonstrate that ac53 is involved in nucleocapsid assembly and is an essential gene for virus production.

  19. Software Development for ALMA in Chile: The ACS-UTFSM Group.

    NASA Astrophysics Data System (ADS)

    von Brand, H. H.

    ALMA Common Software (ACS) provides a common software framework for ALMA, the Atacama Large Millimeter Array in Chile. ACS is a collection of well-documented patterns for controlling systems and a set of components written to those patterns. In its core, ACS is a distributed, object-oriented system, written on top of CORBA. The ACS-UTFSM Group started as some students of informatics did summer jobs at the La Silla Observatory of ESO, where they became acquainted with ACS. Their interest led them to continue working on ACS on their own, and they eventually became official developers of the package. Now the group is being funded by project ALMA-CONICYT 31060008 ``Software Development for ALMA: Building Up Expertise to Meet ALMA Software Requirements within a Chilean University''. Several members of the original group are now working for ALMA, which fullfills one of the goals of the project. Some parts of ACS developed by the ACS-UTFSM Group include H3E (Hardware End-to-End Example), a Lego model of a telescope and its controlling software for training and demonstration purposes; and CDBChecker, a tool to verify the consistency of the configuration database for a ACS deployment. Currently we are working towards a general framework for telescope control using ACS, in order to simplify the deployment of new instruments; and repackaging ACS so it is easier to install and use. A master's thesis is exploring the real-time requirements of ACS.

  20. 21 CFR 880.5510 - Non-AC-powered patient lift.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Non-AC-powered patient lift. 880.5510 Section 880.5510 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Devices § 880.5510 Non-AC-powered patient lift. (a) Identification. A non-AC-powered patient lift is...

  1. AC Losses in the MICE Channel Magnets -- Is This a Curse or aBlessing?

    SciTech Connect

    Green, M.A.; Wu, H.; Wang, L.; Kai, L.L.; Jia, L.X.; Yang, S.Q.

    2008-01-31

    This report discusses the AC losses in the MICE channelmagnets during magnet charging and discharging. This report talks aboutthe three types of AC losses in the MICE magnets; the hysteretic AC lossin the superconductor, the coupling AC loss in the superconductor and theeddy current AC loss in the magnet mandrel and support structure. AClosses increase the heat load at 4 K. The added heat load increases thetemperature of the second stage of the cooler. In addition, AC losscontributes to the temperature rise between the second stage cold headand the high field point of the magnet, which is usually close to themagnet hot spot. These are the curses of AC loss in the MICE magnet thatcan limit the rate at which the magnet can be charge or discharged. Ifone is willing to allow some of the helium that is around the magnet toboil away during a magnet charge or discharge, AC losses can become ablessing. The boil off helium from the AC losses can be used to cool theupper end of the HTS leads and the surrounding shield. The AC losses arepresented for all three types of MICE magnets. The AC loss temperaturedrops within the coupling magnet are presented as an example of how boththe curse and blessing of the AC losses can be combined.

  2. Autographa californica multiple nucleopolyhedrovirus ac76 is involved in intranuclear microvesicle formation.

    PubMed

    Hu, Zhaoyang; Yuan, Meijin; Wu, Wenbi; Liu, Chao; Yang, Kai; Pang, Yi

    2010-08-01

    In this study, we characterized Autographa californica multiple nucleopolyhedrovirus (AcMNPV) orf76 (ac76), which is a highly conserved gene of unknown function in lepidopteran baculoviruses. Transcriptional analysis of ac76 revealed that transcription of multiple overlapping multicistronic transcripts initiates from a canonical TAAG late-transcription start motif but terminates at different 3' ends at 24 h postinfection in AcMNPV-infected Sf9 cells. To investigate the role of ac76 in the baculovirus life cycle, an ac76-knockout virus was constructed using an AcMNPV bacmid system. Microscopy, titration assays, and Western blot analysis demonstrated that the resulting ac76-knockout virus was unable to produce budded viruses. Quantitative real-time PCR analysis demonstrated that ac76 deletion did not affect viral DNA synthesis. Electron microscopy showed that virus-induced intranuclear microvesicles as well as occlusion-derived virions were never observed in cells transfected with the ac76-knockout virus. Confocal microscopy analysis revealed that Ac76 was predominantly localized to the ring zone of nuclei during the late phase of infection. This suggests that ac76 plays a role in intranuclear microvesicle formation. To the best of our knowledge, this is the first baculovirus gene identified to be involved in intranuclear microvesicle formation.

  3. Autographa californica multiple nucleopolyhedrovirus ac53 plays a role in nucleocapsid assembly.

    PubMed

    Liu, Chao; Li, Zhaofei; Wu, Wenbi; Li, Lingling; Yuan, Meijin; Pan, Lijing; Yang, Kai; Pang, Yi

    2008-12-01

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) orf53 (ac53) is a highly conserved gene existing in all sequenced Lepidoptera and Hymenoptera baculoviruses, but its function remains unknown. To investigate its role in the baculovirus life cycle, an ac53 deletion virus (vAc(ac53KO-PH-GFP)) was generated through homologous recombination in Escherichia coli. Fluorescence and light microscopy and titration analysis revealed that vAc(ac53KO-PH-GFP) could not produce infectious budded virus in infected Sf9 cells. Real-time PCR demonstrated that the ac53 deletion did not affect the levels of viral DNA replication. Electron microscopy showed that many lucent tubular shells devoid of the nucleoprotein core are present in the virogenic stroma and ring zone, indicating that the ac53 knockout affected nucleocapsid assembly. With a recombinant virus expressing an Ac53-GFP fusion protein, we observed that Ac53 was distributed within the cytoplasm and nucleus at 24 h post-infection, but afterwards accumulated predominantly near the nucleus-cytoplasm boundary. These data demonstrate that ac53 is involved in nucleocapsid assembly and is an essential gene for virus production.

  4. 21 CFR 880.5510 - Non-AC-powered patient lift.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Non-AC-powered patient lift. 880.5510 Section 880... Devices § 880.5510 Non-AC-powered patient lift. (a) Identification. A non-AC-powered patient lift is a hydraulic, battery, or mechanically powered device, either fixed or mobile, used to lift and transport...

  5. 21 CFR 880.5510 - Non-AC-powered patient lift.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Non-AC-powered patient lift. 880.5510 Section 880... Devices § 880.5510 Non-AC-powered patient lift. (a) Identification. A non-AC-powered patient lift is a hydraulic, battery, or mechanically powered device, either fixed or mobile, used to lift and transport...

  6. 21 CFR 880.5510 - Non-AC-powered patient lift.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Non-AC-powered patient lift. 880.5510 Section 880... Devices § 880.5510 Non-AC-powered patient lift. (a) Identification. A non-AC-powered patient lift is a hydraulic, battery, or mechanically powered device, either fixed or mobile, used to lift and transport...

  7. 21 CFR 880.5510 - Non-AC-powered patient lift.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Non-AC-powered patient lift. 880.5510 Section 880... Devices § 880.5510 Non-AC-powered patient lift. (a) Identification. A non-AC-powered patient lift is a hydraulic, battery, or mechanically powered device, either fixed or mobile, used to lift and transport...

  8. Examining the Effects of Introducing Online Access to ACS Journals at Primarily Undergraduate Institutions

    ERIC Educational Resources Information Center

    Landolt, R. G.

    2007-01-01

    In collaboration with the Publications Division of the American Chemical Society (ACS), students and faculty at 24 primarily undergraduate institutions were provided online access to ACS primary research journals for a period of 18 months, and a group of eight schools were granted access to use the archives of ACS journals for a year. Resources…

  9. AcMNPV Core Gene ac109 Is Required for Budded Virion Transport to the Nucleus and for Occlusion of Viral Progeny

    PubMed Central

    Alfonso, Victoria; Maroniche, Guillermo A.; Reca, Sol R.; López, María Gabriela; del Vas, Mariana; Taboga, Oscar

    2012-01-01

    The Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac109 core gene has been previously characterized as an essential late gene. Our results showed that budded virions could be detected in supernatants of infected Sf-9 cells, even when ac109 knockout viruses displayed a single-cell infection phenotype. Moreover, confocal microscopy analysis revealed that budded virions can enter the cytoplasm but are unable to enter the cell nucleus. This defect could be repaired by complementing ac109 in trans. In addition, polyhedra of normal size could be detected in Sf-9 nuclei infected with ac109 knockout viruses. However, electron microscopy demonstrated that these occlusion bodies were empty. Altogether, these results indicate that ac109 is required for infectivity of both phenotypes of virus. PMID:23049963

  10. Characterization of an Ac transposon system based on apt1-m1 (Ac) on the long arm of maize chromosome 9.

    PubMed

    Wang, Fei; Li, Pengfei; Tang, Yuanping; Fan, Jun; Xu, Dabin; Guo, Shengming; Xu, Zhengkai; Song, Rentao

    2012-09-01

    Activator/Dissociation (Ac/Ds) transposable elements have been used in maize insertional mutagenesis as a complement to Mutator (Mu). In this study, to further improve the efficiency of the Ac/Ds mutagenesis system, we adopted apt1-m1 (Ac) on the long arm of chromosome 9 (9L) as a donor Ac to create an Ac insertion library. This system is based on the negative selection pressure against the donor Ac, and it was highly efficient for isolating new transposition events. We obtained 9,625 transposition events from 1083 F1 ears with an average transposition rate of 8.66 % (rates ranged from 1.11 to 29.73 %). We also adopted a modified PCR-based genome walking strategy to improve the efficiency of the new method for isolating transposon-flanking sequences. This method is more efficient than the Southern-based method that was used in previous studies. A validation step was developed to distinguish transposon tags derived from newly transposed Ac or Ds elements. Using this PCR-based method, we isolated 67 inheritable flanking sequences from the apt1-m1 (Ac) transposition library; of these, 51 were confirmed as tr-Ac-flanking sequences and 11 were tr-Ds-flanking sequences. Similar to other Ac donors from different loci, the apt1-m1 (Ac) system also exhibited a preference for short distance transposition. In this study, we have further improved the Ac mutagenesis system in maize for gene isolation and functional genomics studies.

  11. Characterization of flow-through electrode processes by AC impedance

    SciTech Connect

    Yuh, C.Y. ); Selman, J.R. )

    1993-04-01

    Flow-through porous electrodes, such as packed-bed and fluidized-bed electrodes, are attractive for electrowinning, electro-organic synthesis and flow-battery applications. The extensive surface area of the porous electrodes makes high volumetric reaction rate more possible than in a cell with smooth electrodes. Forced convection also enhances mass-transfer rate and hence reduces concentration polarization. AC-impedance method has been used successfully in characterizing a packed-bed flow-through electrode system. A macrohomogeneous model was developed to simulate the effect of structural, physical and flow parameters. The relative importance of kinetics and mass transfer can be inferred from the AC-impedance analysis. Kinetic information about copper deposition in supported cupric sulfate solution has been obtained successfully using this technique.

  12. AC operation and runaway electron behaviour in HT-7 tokamak

    NASA Astrophysics Data System (ADS)

    Lu, Hong-Wei; Hu, Li-Qun; Zhou, Rui-Jie; Lin, Shi-Yao; Zhong, Guo-Qiang; Wang, Shao-Feng; Chen, Kai-Yun; Xu, Ping; Zhang, Ji-Zong; Ling, Bi-Li; Mao, Song-Tao; Duan, Yan-Min

    2010-06-01

    Operation of HT-7 tokamak in a multicycle alternating square wave plasma current regime is reported. A set of AC operation experiments, including LHW heating to enhance plasma ionization during the current transition and current sustainment, is described. The behaviour of runaway electrons is analysed by four HXR detectors tangentially viewing the plasma in the equatorial plane, within energy ranges 0.3-1.2 MeV and 0.3-7 MeV, separately. High energy runaway electrons (~MeV) are found to circulate predominantly in the opposite direction to the plasma current, while the number of low energy runaway electrons (~tens to hundreds of keV) circulating along the plasma current is comparable to that in the direction opposite to the plasma current. AC operation with lower hybrid current drive (LHCD) is observed to have an additional benefit of suppressing the runaway electrons if the drop of the loop voltage is large enough.

  13. Towards an AC-MOT of CaF

    NASA Astrophysics Data System (ADS)

    Anderegg, Loic; Chae, Eunmi; Ravi, Aakash; Augenbraun, Benjamin; Hemmerling, Boerge; Drayna, Garrett; Hutzler, Nicholas; Collopy, Alejandra; Wu, Yewei; Ding, Shiqian; Ye, Jun; Ketterle, Wolfgang; Doyle, John

    2016-05-01

    Ultra-cold diatomic molecules have rich prospects as candidates to study controlled ultra-cold chemistry, strongly correlated systems and precision measurements. They are also considered as possible qubits in quantum computing and simulation schemes. We report on progress towards loading CaF into a molecular magneto-optical trap (MOT). An AC-MOT will be used to actively remix magnetic dark states via both polarization and magnetic field switching. In order to load a molecular MOT, we have successfully laser slowed a CaF beam to near the expected capture velocity. We describe our AC-MOT apparatus, which is designed to co-trap CaF and Li. We outline our planned study of CaF-Li collisions to explore the feasibility of sympathetically cooling molecules to ultra-cold temperatures.

  14. Final Report for the Advanced Camera for Surveys (ACS)

    NASA Technical Reports Server (NTRS)

    2004-01-01

    ACS was launched aboard the Space Shuttle Columbia just before dawn on March 1, 2002. At the time of liftoff, the Hubble Space Telescope (HST) was reflecting the early morning sun as it moved across the sky. After successfully docking with HST, several components were replaced. One of the components was the Advanced Camera for Surveys built by Ball Aerospace & Technologies Corp. (BATC) in Boulder, Colorado. Over the life of the HST contract at BATC, hundreds of employees had the pleasure of working on the concept, design, fabrication, assembly, and test of ACS. Those employees thank NASA - Goddard Space Flight Center and the science team at Johns Hopkins University (JHU) for the opportunity to participate in building a great science instrument for HST.

  15. ac power control in the Core Flow Test Loop

    SciTech Connect

    McDonald, D.W.

    1980-01-01

    This work represents a status report on a development effort to design an ac power controller for the Core Flow Test Loop. The Core Flow Test Loop will be an engineering test facility which will simulate the thermal environment of a gas-cooled fast-breeder reactor. The problems and limitations of using sinusoidal ac power to simulate the power generated within a nuclear reactor are addressed. The transformer-thyristor configuration chosen for the Core Flow Test Loop power supply is presented. The initial considerations, design, and analysis of a closed-loop controller prototype are detailed. The design is then analyzed for improved performance possibilities and failure modes are investigated at length. A summary of the work completed to date and a proposed outline for continued development completes the report.

  16. The Study of Porous Media with AC Electrokinetics

    NASA Astrophysics Data System (ADS)

    Pengra, David B.; Wong, Po-Zen

    1996-11-01

    Electrokinetic phenomena, which involve the coupling of fluid and electric currents, are present in many porous media systems. They arise from the presence of a space charge layer at the fluid/solid interface, and depend on characteristics of the interface and properties of the porous material. Although understood for years, electrokinetic phenomena have been typically too weak to use as an experimental probe of such systems. Recently we have shown that modern instrumentation, based on AC excitations, can be used to measure electrokinetic response in porous rock. From the measurements we derive the permeability of the rock exactly, and study other physicochemical properties. We review electrokinetic theory, describe our results for porous rock, and discuss present research using the AC techniques. Research supported by the Gas Research Institute, Contract 5090-260-1953, and National Science Foundation Grant DMR-9405672.

  17. Improvement program for polycarbonate capacitors. [hermetically sealed, and ac wound

    NASA Technical Reports Server (NTRS)

    Bailey, R. R.; Waterman, K. D.

    1973-01-01

    Hermetically sealed, wound, AC, polycarbonate capacitors incorporating design improvements recommended in a previous study were designed and built. A 5000 hour, 400 Hz ac life test was conducted using 384 of these capacitors to verify the adequacy of the design improvements. The improvements incorporated in the capacitors designed for this program eliminated the major cause of failure found in the preceding work, termination failure. A failure cause not present in the previous test became significant in this test with capacitors built from one lot of polycarbonate film. The samples from this lot accounted for 25 percent of the total test complement. Analyses of failed samples showed that the film had an excessive solvent content. This solvent problem was found in 37 of the total 46 failures which occurred in this test. The other nine were random failures resulting from causes such as seal leaks, foreign particles, and possibly wrinkles.

  18. [Effect of prostatilen AC suppositories on course of experimental prostatitis].

    PubMed

    Savateeva-Liubimova, T N; Sivak, K V; Malinin, V V

    2012-01-01

    The article presents the results of evaluation of efficacy of new drug prostatilen AC (rectal suppositories), containing regulatory peptides of the bovine prostate and zinc arginate-glycinate complex, in the treatment of prostatitis. The experiment was conducted on 40 Sprague-Dawley rats weighing 180-200 g. Chronic prostatitis was modeled by injection of 10% Dimexidum in combination with water, mixed with turpentine, a volumetric ratio of 4:1. It is shown that prostatilen AC has pronounced organotropic antiinflammatory effect, which manifests in reducing the weight of the prostate, reducing the protein level in the urine, activity of acid phosphatase, and levels of ceruloplasmin and C-reactive protein. In addition, this drug normalizes the act of urination and increases the diurnal diuresis, has antioxidant properties and increases the blood level of the male sex hormone testosterone.

  19. Development of ac corona discharge modes at atmospheric pressure

    SciTech Connect

    El-Koramy, Reda Ahmed; Yehia, Ashraf; Omer, Mohamed

    2011-02-15

    Corona discharges in gases exist under several distinctive forms. In this paper, a survey study has been made of ac corona discharge modes generated in some different gases fed in a wire-duct reactor with a constant rate of flowing at atmospheric pressure. The properties of different corona modes are analyzed under some condition transitions from Trichel pulses to a steady glow. In the course of the presented experimental work, numerous apparent contradictions with earlier observations necessitated further study and are given to provide more information on the physical mechanisms of the ac corona discharges. Furthermore, we have gained insight into some new technologies and applications of the environmentally friendly corona and plasma discharges.

  20. Measured losses in superconductor magnets for 60-Hertz ac operation.

    NASA Technical Reports Server (NTRS)

    Hamlet, I. L.; Kilgore, R. A.

    1971-01-01

    Results of an experimental study of electrical losses in superconductor magnets. Preliminary 60-Hz ac loss data are presented for coils constructed of Nb3Sn ribbon, Nb-Ti cable, and multifilament Nb-Ti. Losses have been measured for different size coils up to approximately 20 cm in diameter. Of the conductor types tested, Nb3Sn ribbon has the lowest losses for ac operation. In Nb3Sn-ribbon coils of different sizes, the loss per unit length of conductor is shown to decrease with a decrease in the rate of change of current and to increase, in general, with increase in coil size. An important aspect of the study is the high degree of repeatability of the data.

  1. On-Chip AC self-test controller

    DOEpatents

    Flanagan, John D.; Herring, Jay R.; Lo, Tin-Chee

    2009-09-29

    A system for performing AC self-test on an integrated circuit that includes a system clock for normal operation is provided. The system includes the system clock, self-test circuitry, a first and second test register to capture and launch test data in response to a sequence of data pulses, and a logic circuit to be tested. The self-test circuitry includes an AC self-test controller and a clock splitter. The clock splitter generates the sequence of data pulses including a long data capture pulse followed by an at speed data launch pulse and an at speed data capture pulse followed by a long data launch pulse. The at speed data launch pulse and the at speed data capture pulse are generated for a common cycle of the system clock.

  2. AC Magnetic Field Frequency Dependence of Magnetoacoustic Emission

    NASA Technical Reports Server (NTRS)

    Namkung, M.; Wincheski, B.; Fulton, J. P.; DeNale, R.

    1992-01-01

    Our recent study has proved a strong correlation between the low-frequency AC applied magnetic field amplitude dependence of the asymmetry of the magnetoacoustic emission (MAE) burst and the strength of the domain wall-defect interaction in iron-base ferromagnets. For the present study the AC magnetic field frequency dependence of the asymmetry has been investigated in the range of 1 to 200 Hz. When represented by the third moment of the rectified acoustic emission pulses, the asymmetry becomes a bell-shaped function of frequency with its center located around 25 Hz. This experiment has been performed with low carbon, high yield stress steel specimens of three different levels of domain wall-defect interaction strength. The results show that the increase in the interaction strength causes a vertical down shift of the asymmetry in the entire frequency range investigated.

  3. Ac magnetic susceptibility study of in vivo nanoparticle biodistribution

    NASA Astrophysics Data System (ADS)

    Gutiérrez, L.; Mejías, R.; Barber, D. F.; Veintemillas-Verdaguer, S.; Serna, C. J.; Lázaro, F. J.; Morales, M. P.

    2011-06-01

    We analysed magnetic nanoparticle biodistribution, before and after cytokine conjugation, in a mouse model by ac susceptibility measurements of the corresponding resected tissues. Mice received repeated intravenous injections of nanoparticle suspension for two weeks and they were euthanized 1 h after the last injection. In general, only 10% of the total injected nanoparticles after multiple exposures were found in tissues. The rest of the particles may probably be metabolized or excreted by the organism. Our findings indicate that the adsorption of interferon to DMSA-coated magnetic nanoparticles changes their biodistribution, reducing the presence of nanoparticles in lungs and therefore their possible toxicity. The specific targeting of the particles to tumour tissues by the use of an external magnetic field has also been studied. Magnetic nanoparticles were observed by transmission electron microscopy in the targeted tissue and quantified by ac magnetic susceptibility.

  4. Diagnostic of water trees using DC and AC voltages

    SciTech Connect

    Romero, P.; Puerta, J.

    1996-12-31

    Electric tools for non-destructive water tree diagnostic in XLPE medium voltage cables, by means of DC and AC voltages are presented. The DC method is related to the determination of a non-linear dependence of the polarization current on the applied DC step voltage, in contrast to a linear dependence found in non-water tree-damaged cables. In both cases the current follows the Curie-von Schweidler empirical law, I(t) = I{sub 0}t{sup {minus}n}. The AC method is based on the measurement of the dispersion relation of both the loss factor and the capacitance in the low and very low frequency ranges by means of the Fourier Transform techniques. The devised measuring instrumentation is presented.

  5. Bouncing of a Droplet on Superhydrophobic Surface in AC Electrowetting

    NASA Astrophysics Data System (ADS)

    Kang, Kwan Hyoung; Lee, Seung Jun; Hong, Jiwoo

    2009-11-01

    Oscillation of a droplet is induced in ac electrowetting by time-dependent electrical wetting tension. A droplet placed on a superhydrophobic surface bounces up like a rubber ball when an ac signal is applied. The bouncing pattern is highly frequency dependent. We investigated how the shape deformation and bouncing of a droplet are affected by applied frequency. The droplet motion is analyzed with the spectral method. The droplet is modeled as a simple linear oscillator, and the mass and spring constants are determined based on analytical results. We found that bouncing occurs periodically at a resonance frequency of the droplet. The motion of a sessile droplet released from a fixed shape is analyzed based on the phase field method. The numerical results show qualitative agreement with the experimental results for a bouncing droplet. Details on the flow field inside a bouncing droplet will be discussed based on numerical results.

  6. SNL software manual for the ACS Data Analytics Project.

    SciTech Connect

    Stearley, Jon R.; McLendon, William Clarence, III; Rodrigues, Arun F.; Williams, Aaron S.; Hooper, Russell Warren; Robinson, David Gerald; Stickland, Michael G.

    2011-10-01

    In the ACS Data Analytics Project (also known as 'YumYum'), a supercomputer is modeled as a graph of components and dependencies, jobs and faults are simulated, and component fault rates are estimated using the graph structure and job pass/fail outcomes. This report documents the successful completion of all SNL deliverables and tasks, describes the software written by SNL for the project, and presents the data it generates. Readers should understand what the software tools are, how they fit together, and how to use them to reproduce the presented data and additional experiments as desired. The SNL YumYum tools provide the novel simulation and inference capabilities desired by ACS. SNL also developed and implemented a new algorithm, which provides faster estimates, at finer component granularity, on arbitrary directed acyclic graphs.

  7. On the possibility of reduction of Ac{sup 3+} to Ac{sup 2+} in Aqueous-ethanolic solutions of bivalent samarium

    SciTech Connect

    Mikheev, N.B.; Veleshko, I.E.; Kamenskaya, A.N.

    1995-07-01

    In view of contradictory data on the existence of Ac{sup 2+} in aqueous solutions, the possibility of actinium reduction was examined in aqueous-ethanolic solutions in which bivalent f-elements are more stable than in aqueous media. In the presence of bivalent samarium (E{sub Sm}{sup 0}3+/Sm 2+=-1.5 V) Ac(III) is not reduced to Ac(II). These results disagree with the previously published data on the radiopolarographic generation of Ac(II) in aqueous solutions.

  8. Challenges and solutions in medically managed ACS in the Asia-Pacific region: expert recommendations from the Asia-Pacific ACS Medical Management Working Group.

    PubMed

    Huo, Yong; Thompson, Peter; Buddhari, Wacin; Ge, Junbo; Harding, Scott; Ramanathan, Letchuman; Reyes, Eugenio; Santoso, Anwar; Tam, Li-Wah; Vijayaraghavan, Govindan; Yeh, Hung-I

    2015-03-15

    Acute coronary syndromes (ACS) remain a leading cause of mortality and morbidity in the Asia-Pacific (APAC) region. International guidelines advocate invasive procedures in all but low-risk ACS patients; however, a high proportion of ACS patients in the APAC region receive solely medical management due to a combination of unique geographical, socioeconomic, and population-specific barriers. The APAC ACS Medical Management Working Group recently convened to discuss the ACS medical management landscape in the APAC region. Local and international ACS guidelines and the global and APAC clinical evidence-base for medical management of ACS were reviewed. Challenges in the provision of optimal care for these patients were identified and broadly categorized into issues related to (1) accessibility/systems of care, (2) risk stratification, (3) education, (4) optimization of pharmacotherapy, and (5) cost/affordability. While ACS guidelines clearly represent a valuable standard of care, the group concluded that these challenges can be best met by establishing cardiac networks and individual hospital models/clinical pathways taking into account local risk factors (including socioeconomic status), affordability and availability of pharmacotherapies/invasive facilities, and the nature of local healthcare systems. Potential solutions central to the optimization of ACS medical management in the APAC region are outlined with specific recommendations.

  9. Removal of pharmaceutically active compounds (PhACs) and toxicological response of Cyperus alternifolius exposed to PhACs in microcosm constructed wetlands.

    PubMed

    Yan, Qing; Feng, Guozhong; Gao, Xu; Sun, Chengxiao; Guo, Jin-song; Zhu, Zhiwei

    2016-01-15

    This study investigated the effects of selected four pharmaceutically active compounds (PhACs) (carbamazepine, sulfamethoxazole, ofloxacin, and roxithromycin) on the photosynthesis and antioxidant enzymes of Cyperus alternifolius in constructed wetlands (CWs). Moreover, the removal and kinetics of PhACs in CWs were evaluated to explore the related removal mechanisms. Results showed that C. alternifolius can uptake and withstand certain PhACs. The PhAC tolerance of C. alternifolius might be attributed to their capacity to maintain relatively normal photosynthetic activity and elevated antioxidative defense. CWs offered comparable or even higher removal efficiencies for the selected PhACs compared with conventional WWTPs. The removal of the target PhACs was enhanced in the planted CWs versus the unplanted CWs mostly because of plant uptake and rhizosphere effects. In particular, carbamazepine, which is considered the most recalcitrant of the PhACs, was significantly reduced (p<0.05). The removal of target PhACs fitted into two distinct periods. The initial fast step (within the first 2 h) was essentially attributed to the adsorption onto the CW medium surface. The subsequent slow process (2-12 h) closely followed first-order kinetics probably because of the interaction between microorganisms and plants. The obtained results indicate that C. alternifolius can phytoremediate PhAC-contaminated waters in CWs. PMID:26465971

  10. Removal of pharmaceutically active compounds (PhACs) and toxicological response of Cyperus alternifolius exposed to PhACs in microcosm constructed wetlands.

    PubMed

    Yan, Qing; Feng, Guozhong; Gao, Xu; Sun, Chengxiao; Guo, Jin-song; Zhu, Zhiwei

    2016-01-15

    This study investigated the effects of selected four pharmaceutically active compounds (PhACs) (carbamazepine, sulfamethoxazole, ofloxacin, and roxithromycin) on the photosynthesis and antioxidant enzymes of Cyperus alternifolius in constructed wetlands (CWs). Moreover, the removal and kinetics of PhACs in CWs were evaluated to explore the related removal mechanisms. Results showed that C. alternifolius can uptake and withstand certain PhACs. The PhAC tolerance of C. alternifolius might be attributed to their capacity to maintain relatively normal photosynthetic activity and elevated antioxidative defense. CWs offered comparable or even higher removal efficiencies for the selected PhACs compared with conventional WWTPs. The removal of the target PhACs was enhanced in the planted CWs versus the unplanted CWs mostly because of plant uptake and rhizosphere effects. In particular, carbamazepine, which is considered the most recalcitrant of the PhACs, was significantly reduced (p<0.05). The removal of target PhACs fitted into two distinct periods. The initial fast step (within the first 2 h) was essentially attributed to the adsorption onto the CW medium surface. The subsequent slow process (2-12 h) closely followed first-order kinetics probably because of the interaction between microorganisms and plants. The obtained results indicate that C. alternifolius can phytoremediate PhAC-contaminated waters in CWs.

  11. Hybrid immersed interface-immersed boundary methods for AC dielectrophoresis

    SciTech Connect

    Hossan, Mohammad Robiul; Dillon, Robert; Dutta, Prashanta

    2014-08-01

    Dielectrophoresis, a nonlinear electrokinetic transport mechanism, has become popular in many engineering applications including manipulation, characterization and actuation of biomaterials, particles and biological cells. In this paper, we present a hybrid immersed interface–immersed boundary method to study AC dielectrophoresis where an algorithm is developed to solve the complex Poisson equation using a real variable formulation. An immersed interface method is employed to obtain the AC electric field in a fluid media with suspended particles and an immersed boundary method is used for the fluid equations and particle transport. The convergence of the proposed algorithm as well as validation of the hybrid scheme with experimental results is presented. In this paper, the Maxwell stress tensor is used to calculate the dielectrophoretic force acting on particles by considering the physical effect of particles in the computational domain. Thus, this study eliminates the approximations used in point dipole methods for calculating dielectrophoretic force. A comparative study between Maxwell stress tensor and point dipole methods for computing dielectrophoretic forces are presented. The hybrid method is used to investigate the physics of dielectrophoresis in microfluidic devices using an AC electric field. The numerical results show that with proper design and appropriate selection of applied potential and frequency, global electric field minima can be obtained to facilitate multiple particle trapping by exploiting the mechanism of negative dielectrophoresis. Our numerical results also show that electrically neutral particles form a chain parallel to the applied electric field irrespective of their initial orientation when an AC electric field is applied. This proposed hybrid numerical scheme will help to better understand dielectrophoresis and to design and optimize microfluidic devices.

  12. A calculable, transportable audio-frequency AC reference standard

    SciTech Connect

    Oldham, N.M.; Hetrick, P.S. ); Zeng, X. )

    1989-04-01

    A transportable ac voltage source is described, in which sinusoidal signals are synthesized digitally in the audio-frequency range. The rms value of the output waveform may be calculated by measuring the dc level of the individual steps used to generate the waveform. The uncertainty of this calculation at the 7-V level is typically less than +-5 ppm from 60 Hz to 2 kHz and less than +-10 ppm from 30 Hz to 15 kHz.

  13. Leonurenones A-C: Labdane diterpenes from Leonotis leonurus.

    PubMed

    He, Fang; Lindqvist, Charlotte; Harding, Wayne W

    2012-11-01

    Labdanes, leonurenones A-C, two known labdanes, luteolin 7-O-β-glucoside and luteolin were isolated and characterized from a commercial source of Leonotis leonurus. Genetic methods allowed for identification of the plant material. The leonurenones contain an uncommon α,β-unsaturated enone moiety in ring B, and leonurenones A and B were evaluated in a competitive inhibition assay at the GABA A neuroreceptor site.

  14. Effective AC needleless and collectorless electrospinning for yarn production.

    PubMed

    Pokorny, P; Kostakova, E; Sanetrnik, F; Mikes, P; Chvojka, J; Kalous, T; Bilek, M; Pejchar, K; Valtera, J; Lukas, D

    2014-12-28

    Nanofibrous materials are essential components for a wide range of applications, particularly in the fields of medicine and material engineering. These include protective materials, sensors, cosmetics, hygiene, filtration and energy storage. The most widely used and researched technology in these fields is electrospinning. This method for producing fibers yields highly promising results thanks to its versatility and simplicity. Electrospinning is employed in multiple forms, among which needle and needleless direct current (DC) variants are the most distinctive. The former is based on the generation of just one single jet from a nozzle; hence this fabrication process is not very productive. The latter uses the destabilization of free liquid surfaces by means of an electric field, which enhances the throughput since it produces numerous jets, emitted from the surfaces of rollers, spheres, strings and spirals. However, although some progress in total producibility has been achieved, the efficiency of the DC method still remains relatively low. A further drawback of DC electrospinning is that both variants need a collector, which makes it difficult to combine DC electrospinning easily with other technologies due to the presence of the high field strength within the entire spinning zone. This paper describes our experiments with AC electrospinning. We show that alternating current (AC) electrospinning based on a needleless spinning-electrode provides a highly productive smoke-like aerogel composed of nanofibers. This aerogel rises rapidly from the electrode like a thin plume of smoke, without any need for a collector. Our work shows that AC needleless electrospinning gains its efficiency and collector-less feature thanks to the creation of a perpetually charge-changing virtual counter-electrode composed of the nanofibers emitted. High-speed camera recordings demonstrate the formation mechanism of the nanofibrous plume, which is wafted by an electric wind. This wind

  15. Heat Capacity Measurements by Simultaneous Relaxation and AC-Calorimetry

    NASA Astrophysics Data System (ADS)

    Kashuri, H.; Kashuri, K.; Iannacchione, G. S.

    2012-02-01

    A high-resolution method for measuring the heat capacity Cp using simultaneously AC and Relaxation Calorimetry techniques has been developed. This technique is useful for both first and second-order phase transitions of liquids and complex fluids. The difference of the Cp's measured by the Relaxation and AC calorimetry is a direct measurement of a phase transitions' latent heat. As a test, the Cp of two cyanobiphenyl liquid crystals, 5CB and 8CB, were measured using a square wave modulation pulse train over a base temperature range from 300 to 320 K in which 5CB exhibits a first-order phase transition and 8CB exhibits a first and second-order phase transition. Fourier transform analysis allows for the direct Cp measurement at the fundamental frequency of the square wave pulse train (as well as higher frequency orders) as function of temperature (i.e., AC-mode). The heating and cooling relaxations at the beginning and end of the square pulse heating allows for a relaxation analysis of Cp by applying the dual slope-method that includes all enthalpic conversions.

  16. Transcriptome modulations due to A/C2 plasmid acquisition.

    PubMed

    Lang, Kevin S; Johnson, Timothy J

    2015-07-01

    Plasmids play an important role in driving the genetic diversity of bacteria. Horizontal gene transfer via plasmids is crucial for the dissemination of antimicrobial resistance genes. Many factors contribute to the persistence of plasmids within bacterial populations, and it has been suggested that epistatic interactions between the host chromosome and plasmid contribute to the fitness of a particular plasmid-host combination. However, such interactions have been shown to differ between bacterial hosts. In this study, RNA-Seq was performed in six different strains, spanning three species, to characterize the influence of host background on the A/C2 plasmid transcriptome. In five of these strains, chromosomal transcriptomes were compared in the presence and absence of A/C2 plasmid pAR060302. Host-specific effects on plasmid gene expression were identified, and acquisition of pAR060302 resulted in changes in the expression of chromosomal genes involved in metabolism and energy production. These results suggest that A/C2 plasmid fitness is, in part, dependent on host chromosome content, as well as environmental factors. PMID:26079188

  17. AC Conductivity and Dielectric Properties of Borotellurite Glass

    NASA Astrophysics Data System (ADS)

    Taha, T. A.; Azab, A. A.

    2016-10-01

    Borotellurite glasses with formula 60B2O3-10ZnO-(30 - x)NaF- xTeO2 ( x = 0 mol.%, 5 mol.%, 10 mol.%, and 15 mol.%) have been synthesized by thermal melting. X-ray diffraction (XRD) analysis confirmed that the glasses were amorphous. The glass density ( ρ) was determined by the Archimedes method at room temperature. The density ( ρ) and molar volume ( V m) were found to increase with increasing TeO2 content. The direct-current (DC) conductivity was measured in the temperature range from 473 K to 623 K, in which the electrical activation energy of ionic conduction increased from 0.27 eV to 0.48 eV with increasing TeO2 content from 0 mol.% to 15 mol.%. The dielectric parameters and alternating-current (AC) conductivity ( σ ac) were investigated in the frequency range from 1 kHz to 1 MHz and temperature range from 300 K to 633 K. The AC conductivity and dielectric constant decreased with increasing TeO2 content from 0 mol.% to 15 mol.%.

  18. AC Conductivity and Dielectric Properties of Borotellurite Glass

    NASA Astrophysics Data System (ADS)

    Taha, T. A.; Azab, A. A.

    2016-06-01

    Borotellurite glasses with formula 60B2O3-10ZnO-(30 - x)NaF-xTeO2 (x = 0 mol.%, 5 mol.%, 10 mol.%, and 15 mol.%) have been synthesized by thermal melting. X-ray diffraction (XRD) analysis confirmed that the glasses were amorphous. The glass density (ρ) was determined by the Archimedes method at room temperature. The density (ρ) and molar volume (V m) were found to increase with increasing TeO2 content. The direct-current (DC) conductivity was measured in the temperature range from 473 K to 623 K, in which the electrical activation energy of ionic conduction increased from 0.27 eV to 0.48 eV with increasing TeO2 content from 0 mol.% to 15 mol.%. The dielectric parameters and alternating-current (AC) conductivity (σ ac) were investigated in the frequency range from 1 kHz to 1 MHz and temperature range from 300 K to 633 K. The AC conductivity and dielectric constant decreased with increasing TeO2 content from 0 mol.% to 15 mol.%.

  19. {alpha} decay of the new isotope {sup 206}Ac

    SciTech Connect

    Eskola, K.; Kuusiniemi, P.; Leino, M.; Cocks, J.F.; Enqvist, T.; Hurskanen, S.; Kettunen, H.; Trzaska, W.H.; Uusitalo, J.; Allatt, R.G.; Greenlees, P.T.; Page, R.D.

    1998-01-01

    The new neutron-deficient nuclide {sup 206}Ac was produced by bombarding a {sup 175}Lu target with 5.5 MeV/nucleon {sup 36}Ar ions. The evaporation residues were separated in flight by a gas-filled separator and subsequently identified by the {alpha}-{alpha} position and time correlation method. {sup 206}Ac was found to have two {alpha} particle emitting isomeric levels with half-lives of (22{sub {minus}5}{sup +9}) ms and (33{sub {minus}9}{sup +22}) ms, and with {alpha} particle energies of (7790{plus_minus}30) keV and (7750{plus_minus}20) keV, respectively. The former isomer is tentatively assigned to a J{sup {pi}}=3{sup +} level and the latter to a J{sup {pi}}=10{sup {minus}} level, both of which are also seen in the daughter and granddaughter nuclides {sup 202}Fr and {sup 198}At. Improved values of (27{sub {minus}6}{sup +11}) ms and (7693{plus_minus}25) keV for the half-life and {alpha} particle energy of {sup 207}Ac are also reported. {copyright} {ital 1998} {ital The American Physical Society}

  20. AC Conductivity Studies of Lithium Based Phospho Vanadate Glasses

    SciTech Connect

    Nagendra, K.; Babu, G. Satish; Gowda, Veeranna; Reddy, C. Narayana

    2011-07-15

    Glasses in the system xLi{sub 2}SO{sub 4}-20Li{sub 2}O-(80-x) [80P{sub 2}O{sub 5}-20V{sub 2}O{sub 5}](5{>=}x{>=}20 mol%) has been prepared by melt quenching method. Dc and ac conductivity has been studied over a wide range of frequency (10 Hz to 10 MHz) and temperature (298 K-523 K). The dc conductivity found to increase with increase of Li{sub 2}SO{sub 4} concentration. The ac conductivities have been fitted to the Almond-West type single power law equation {sigma}({omega}) = {sigma}(0)+A{omega}{sup s} where 's' is the power law exponent. The ac conductivity found to increase with increase of Li{sub 2}SO{sub 4} concentration. An attempt is made to elucidate the enhancement of lithium ion conduction in phosphor-vanadate glasses by considering the expansion of network structure.

  1. AC electrokinetic manipulation of selenium nanoparticles for potential nanosensor applications

    SciTech Connect

    Mahmoodi, Seyed Reza; Bayati, Marzieh; Hosseinirad, Somayeh; Foroumadi, Alireza; Gilani, Kambiz; Rezayat, Seyed Mahdi

    2013-03-15

    Highlights: ► Se nanoparticles were synthesized using a reverse-microemulsion process. ► AC osmotic fluid flow repulses the particles from electrode edges. ► Dielectrophoretic force attracts the particles to electrode edges. ► Dielectrophoresis electrode showed non-ohmic behavior. ► The device can potentially be used as a nanosensor. - Abstract: We report the AC electrokinetic behavior of selenium (Se) nanoparticles for electrical characterization and possible application as micro/nano devices. selenium Se nanoparticles were successfully synthesized using a reverse-microemulsion process and investigated structurally using X-ray diffraction and transmission electron microscope. Interdigitated castellated ITO and non-castellated platinum electrodes were employed for manipulation of suspended materials in the fluid. Using ITO electrodes at low frequency limits resulted in deposition of Se particles on electrode surface. When Se particles exposed to platinum electrodes in the 10 Hz–1 kHz range and V {sub p−p}> 8, AC osmotic fluid flow repulses the particles from electrode edges. However, in 10 kHz–10 MHz range and V {sub p−p}> 5, dielectrophoretic force attracts the particles to electrode edges. As the Se particle concentration increased, the trapped Se particles were aligned along the electric field line and bridged the electrode gap. The device was characterized and can potentially be useful in making micro/nano electronic devices.

  2. Performance testing of the AC propulsion ELX electric vehicle

    NASA Astrophysics Data System (ADS)

    Kramer, W. E.; MacDowall, R. D.; Burke, A. F.

    1994-06-01

    Performance testing of the AC Propulsion ELX electric vehicle is described. Test data are presented and analyzed. The ELX vehicle is the first of a series of electric vehicles of interest to the California Air Resources Board. The test series is being conducted under a Cooperative Research and Development Agreement (CRADA) between the US Department of energy and the California Air Resources Board. The tests which were conducted showed that the AC Propulsion ELX electric vehicle has exceptional acceleration and range performance. When the vehicle's battery was fully charged, the vehicle can accelerate from 0 to 96 km/h in about 10 seconds. Energy consumption and range tests using consecutive FUDS and HWFET Driving cycles (the all-electric cycle) indicate that the energy economy of the AC Propulsion ELX electric vehicle with regenerative braking is 97 W(center dot)h/km, with a range of 153 km (95 miles). Computer simulations performed using the SIMPLEV Program indicate that the vehicle would have a range of 327 km (203 miles) on the all-electric cycle if the lead acid batteries were replaced with NiMH batteries having an energy density of 67 W(center dot)h/kg. Comparisons of FUDS test data with and without regenerative braking indicated that regenerative braking reduced the energy consumption of the ELX vehicle by approximately 25%.

  3. Project Completion Report on China's Room AC Reach Standard

    SciTech Connect

    Lin, Jiang

    2005-03-10

    After much anticipation and hard work, China's reach standard for room air-conditioners was announced in September 2004, with the first tier going into effect on March 1, 2005 and the reach standard taking effect on January 1, 2009. This is a major milestone in the development of minimum energy efficiency standards in China: finally China has set a minimum standard that is meaningful and stringent. According to our preliminary analysis, the majority of room ACs products on the Chinese market in 2004 would not meet the 2009 reach standard requirement. In addition to setting the minimum requirement, China's new AC standard also include classification requirement for the newly established Energy Information Label, as well as the certification requirement for CECP's Energy Conservation Label. Highlights of the 2009 reach standard include: (1) The Chinese Reach Standard for Room AC in 2009 is tighter than American counterpart, and almost matches the efficiency of American Central Air-Conditioners; and (2) Summer peak demand reduction in 2020 due to the reach standard exceeds the capacity of the Three Gorges Project.

  4. The ST-ECF ACS Grism Hubble Legacy Archive Project

    NASA Astrophysics Data System (ADS)

    Kümmel, M.; Kuntschner, H.; Walsh, J. R.; Lombardi, M.; Stoehr, F.; Haase, J.; Hook, R. N.; Rosati, P.; Micol, A.; Fosbury, R.; Freudling, W.

    2009-09-01

    In 2006 the Space Telescope - European Coordinating Facility (ST-ECF), together with its partners at the STScI and the CADC, started a project to build a Hubble Legacy Archive (HLA): a collection of high-level Hubble data products and access tools to ease scientific analysis in the age of the Virtual Observatory. The ST-ECF has focused on providing extracted spectra from slitless spectroscopy HST images. The slitless NICMOS G141 data were presented at previous ADASS meetings and have already been released. In this contribution we present an overview of the ongoing project of processing the ACS/WFC G800L data which cover a larger area and contain more spectra. There are around 150 ACS/WFC G800L datasets covering an area of ˜ 600 arcmin^2, and we expect to extract and publish about 20,000 fully-calibrated spectra. We discuss the techniques and methods that were developed to automatically extract the spectra from the observations and present a selection of ACS/WFC G800L spectra as examples.

  5. Performance testing of the AC propulsion ELX electric vehicle

    SciTech Connect

    Kramer, W.E.; MacDowall, R.D.; Burke, A.F.

    1994-06-01

    Performance testing of the AC Propulsion ELX electric vehicle is described. Test data are presented and analyzed. The ELX vehicle is the first of a series of electric vehicles of interest to the California Air Resources Board. The test series is being conducted under a Cooperative Research and Development Agreement (CRADA) between the US Department of energy and the California Air Resources Board. The tests which were conducted showed that the AC Propulsion ELX electric vehicle has exceptional acceleration and range performance. when the vehicle`s battery was fully charged, the vehicle can accelerate from 0 to 96 km/h in about 10 seconds. Energy consumption and range tests using consecutive FUDS and HWFET Driving cycles (the all-electric cycle) indicate that the energy economy of the AC Propulsion ELX electric vehicle with regenerative braking is 97 W{center_dot}h/km, with a range of 153 km (95 miles). Computer simulations performed using the SIMPLEV Program indicate that the vehicle would have a range of 327 km (203 miles) on the all-electric cycle if the lead acid batteries were replaced with NiMH batteries having an energy density of 67 W{center_dot}h/kg. Comparisons of FUDS test data with and without regenerative braking indicated that regenerative braking reduced the energy consumption of the ELX vehicle by approximately 25%.

  6. Production of AC-225 and application of the BI-213 daughter in cancer therapy

    NASA Astrophysics Data System (ADS)

    Koch, L.; Apostolidis, C.; Janssens, W.; Molinet, R.; van Geel, J.

    1999-01-01

    There are several ongoing medical trials to use Bi-213 conjugated to monoclonal antibodies to kill tumour-cells of various cancer types. The institute is supplying Ac-225 generators for the test and is itself engaged in in-vitro cytotoxicity tests. Nuclear reactions leading to Ac-225 are discussed. The present supply of Ac-225 stems from Th-229 decay obtained from aged U-233. From the possible alternative the reactions Ra-226 (p, 2n) Ac-225 is presently favoured. The fabrication of a Ac-225 for Bi-213 generator will be described.

  7. Optimization of spin-torque switching using AC and DC pulses

    SciTech Connect

    Dunn, Tom; Kamenev, Alex

    2014-06-21

    We explore spin-torque induced magnetic reversal in magnetic tunnel junctions using combined AC and DC spin-current pulses. We calculate the optimal pulse times and current strengths for both AC and DC pulses as well as the optimal AC signal frequency, needed to minimize the Joule heat lost during the switching process. The results of this optimization are compared against numeric simulations. Finally, we show how this optimization leads to different dynamic regimes, where switching is optimized by either a purely AC or DC spin-current, or a combination AC/DC spin-current, depending on the anisotropy energies and the spin-current polarization.

  8. QPSK modulation for AC-power-signal-biased visible light communication system

    NASA Astrophysics Data System (ADS)

    Liu, Yu-Feng; Yeh, Chien-Hung; Chow, Chi-Wai; Liu, Yang

    2013-01-01

    With the integration of light emitting diode (LED), visible light communication (VLC) can provide wireless communication link using the lightning system. Due to the consideration of power efficiency, AC-LED has the design of reducing energy waste with alternating current from the power outlet. In this work, we propose an AC-power-signalbiased system that provides communication on both DC-LED and AC-LED. The bias circuit is designed to combine ACpower signal and the message signal with QPSK format. This driving scheme needs no AC-to-DC converters and it is suitable for driving AC LED. Synchronization is completed to avoid threshold effect of LED.

  9. Quantification of phnAc and nahAc in contaminated New Zealand soils by competitive PCR

    SciTech Connect

    Laurie, A.D.; Lloyd-Jones, G.

    2000-05-01

    Unculturable polycyclic aromatic hydrocarbon (PAH)-degrading bacteria are a significant reservoir of the microbial potential to catabolize low-molecular-weight PAHs. The population of these bacteria is larger than the population of nah-like bacteria that are the dominant organisms in culture-based studies. The authors used the recently described phn genes of Burkholderia sp. strain RP007, which feature only rarely in culture-based studies, as an alternative genotype for naphthalene and phenanthrene degradation and compared this genotype with the genotypically distinct but ubiquitous nah-like class in different soils. Competitive PCR quantification of phnAc and nahAc, which encode the iron sulfur protein large ({alpha}) subunits of PAH dioxygenases in nah-like and phn catabolic operons, revealed that the phn genotype can have a greater ecological significance than the nah-like genotype.

  10. Loss of ACS7 confers abiotic stress tolerance by modulating ABA sensitivity and accumulation in Arabidopsis.

    PubMed

    Dong, Hui; Zhen, Zhiqin; Peng, Jinying; Chang, Li; Gong, Qingqiu; Wang, Ning Ning

    2011-10-01

    The phytohormones ethylene and abscisic acid (ABA) play essential roles in the abiotic stress adaptation of plants, with both cross-talk of ethylene signalling and ABA biosynthesis and signalling reported. Any reciprocal effects on each other's biosynthesis, however, remain elusive. ACC synthase (ACS) acts as the key enzyme in ethylene biosynthesis. A pilot study on changes in ACS promoter activities in response to abiotic stresses revealed the unique involvement in abiotic stress responses of the only type 3 ACC synthase, ACS7, among all nine ACSs of Arabidopsis. Hence an acs7 mutant was characterized and its abiotic stress responses were analysed. The acs7 mutant germinated slightly faster than the wild type and subsequently maintained a higher growth rate at the vegetative growth stage. Ethylene emission of acs7 was merely one-third of that of the wild type. acs7 exhibited enhanced tolerance to salt, osmotic, and heat stresses. Furthermore, acs7 seeds were hypersensitive to both ABA and glucose during germination. Transcript analyses revealed that acs7 had elevated transcript levels of the stress-responsive genes involved in the ABA-dependent pathway under salt stress. The ABA level was also higher in acs7 following salt treatment. Our data suggest that ACS7 acts as a negative regulator of ABA sensitivity and accumulation under stress and appears as a node in the cross-talk between ethylene and ABA.

  11. Phosphor-in-glass for high-powered remote-type white AC-LED.

    PubMed

    Lin, Hang; Wang, Bo; Xu, Ju; Zhang, Rui; Chen, Hui; Yu, Yunlong; Wang, Yuansheng

    2014-12-10

    The high-powered alternating current (AC) light-emitting diode (LED) (AC-LED), featuring low cost, high energy utilization efficiency, and long service life, will become a new economic growth point in the field of semiconductor lighting. However, flicker of AC-LED in the AC cycles is not healthy for human eyes, and therefore need to be restrained. Herein we report an innovation of persistent "phosphor-in-glass" (PiG) for the remote-type AC-LED, whose afterglow can be efficiently activated by the blue light. It is experimentally demonstrated that the afterglow decay of PiG in the microsecond range can partly compensate the AC time gap. Moreover, the substitution of inorganic glass for organic resins or silicones as the encapsulants would bring out several technological benefits to AC-LED, such as good heat-dissipation, low glare, and excellent physical/chemical stability. PMID:25329651

  12. Phosphor-in-glass for high-powered remote-type white AC-LED.

    PubMed

    Lin, Hang; Wang, Bo; Xu, Ju; Zhang, Rui; Chen, Hui; Yu, Yunlong; Wang, Yuansheng

    2014-12-10

    The high-powered alternating current (AC) light-emitting diode (LED) (AC-LED), featuring low cost, high energy utilization efficiency, and long service life, will become a new economic growth point in the field of semiconductor lighting. However, flicker of AC-LED in the AC cycles is not healthy for human eyes, and therefore need to be restrained. Herein we report an innovation of persistent "phosphor-in-glass" (PiG) for the remote-type AC-LED, whose afterglow can be efficiently activated by the blue light. It is experimentally demonstrated that the afterglow decay of PiG in the microsecond range can partly compensate the AC time gap. Moreover, the substitution of inorganic glass for organic resins or silicones as the encapsulants would bring out several technological benefits to AC-LED, such as good heat-dissipation, low glare, and excellent physical/chemical stability.

  13. Electro-orientation of a metal nanowire counterbalanced by thermal torques

    NASA Astrophysics Data System (ADS)

    Arcenegui, Juan J.; García-Sánchez, Pablo; Morgan, Hywel; Ramos, Antonio

    2014-06-01

    The rotational diffusion of electrically polarized metal nanowires suspended in an electrolyte is studied. The alignment of a Brownian nanowire in an ac field with a given direction is not complete due to thermal (fluctuating) torques. The orientation distribution allows us to examine the electrokinetic torques acting on the nanowire for smaller voltages than in previous deterministic experiments. In addition, the torques are obtained without recurring to the rotational friction coefficient as in dynamic deterministic experiments. The present results are in accordance with previous deterministic results of electro-orientation of metal nanowires. Nanowire rotation is originated by both the electrical torque on the induced dipole and by induced-charge electro-osmotic flow around the particle. At low frequencies of the applied ac field, induced-charge electro-osmotic orientation dominates while induced dipole torque orientation dominates at high frequencies. The angular standard deviation and the rotational rate are calculated from the measured fluctuating angle as a function of time, and good agreement with theoretical predictions is found. The experiments at high frequency indicate that the electrical torque on a nanowire near an insulating wall is reduced with respect to the bulk.

  14. Electro-orientation and electrorotation of metal nanowires.

    PubMed

    Arcenegui, Juan J; García-Sánchez, Pablo; Morgan, Hywel; Ramos, Antonio

    2013-12-01

    The physical mechanisms responsible for the electrical orientation and electrical rotation of metal nanowires suspended in an electrolyte as a function of frequency of the applied ac electric field are examined theoretically and experimentally. The alignment of a nanowire in an ac field with a fixed direction is called electro-orientation. The induced constant rotation of a nanowire in a rotating electric field is called electrorotation. In both situations, the applied electric field interacts with the induced charge in the electrical double layer at the metal-electrolyte interface, causing rotation due to the torque on the induced dipole, and also from induced-charge electro-osmotic flow around the particle. First, we describe the dipole theory that describes electro-orientation and electrorotation of perfectly polarizable metal rods. Second, based on a slender approximation, an analytical theory that describes induced-charge electro-orientation and electrorotation of metal nanowires is provided. Finally, experimental measurements of the electro-orientation and electrorotation of metal nanowires are presented and compared with theory, providing a comprehensive study of the relative importance between induced-dipole rotation and induced-charge electro-osmotic rotation.

  15. Electro-orientation of a metal nanowire counterbalanced by thermal torques.

    PubMed

    Arcenegui, Juan J; García-Sánchez, Pablo; Morgan, Hywel; Ramos, Antonio

    2014-06-01

    The rotational diffusion of electrically polarized metal nanowires suspended in an electrolyte is studied. The alignment of a Brownian nanowire in an ac field with a given direction is not complete due to thermal (fluctuating) torques. The orientation distribution allows us to examine the electrokinetic torques acting on the nanowire for smaller voltages than in previous deterministic experiments. In addition, the torques are obtained without recurring to the rotational friction coefficient as in dynamic deterministic experiments. The present results are in accordance with previous deterministic results of electro-orientation of metal nanowires. Nanowire rotation is originated by both the electrical torque on the induced dipole and by induced-charge electro-osmotic flow around the particle. At low frequencies of the applied ac field, induced-charge electro-osmotic orientation dominates while induced dipole torque orientation dominates at high frequencies. The angular standard deviation and the rotational rate are calculated from the measured fluctuating angle as a function of time, and good agreement with theoretical predictions is found. The experiments at high frequency indicate that the electrical torque on a nanowire near an insulating wall is reduced with respect to the bulk.

  16. The dynamic process of atmospheric water sorption in [EMIM][Ac] and mixtures of [EMIM][Ac] with biopolymers and CO2 capture in these systems.

    PubMed

    Chen, Yu; Sun, Xiaofu; Yan, Chuanyu; Cao, Yuanyuan; Mu, Tiancheng

    2014-10-01

    There are mainly three findings related to the dynamic process of atmospheric water sorption in the ionic liquid (IL) 1-ethyl-3-methlyl-imidazolium acetate ([EMIM][Ac]) and its mixtures with biopolymers (i.e., cellulose, chitin, and chitosan), and CO2 capture in these systems above. The analytical methods mainly include gravimetric hygroscopicity measurement and in situ infrared spectroscopy with the techniques of difference, derivative, deconvoluted attenuated total reflectance and two-dimensional correlation. These three findings are listed as below. (1) Pure [EMIM][Ac] only shows a two-regime pattern, while all the mixtures of [EMIM][Ac] with biopolymers (i.e., cellulose, chitin, and chitosan) present a three-regime tendency for the dynamic process of atmospheric water sorption. Specifically, the IL/chitosan mixture has a clear three-regime mode; the [EMIM][Ac]/chitin mixture has an unclear indiscernible regime 3; and the [EMIM][Ac]/cellulose mixture shows an indiscernible regime 2. (2) [EMIM][Ac] and its mixtures with biopolymers could physically absorb a trace amount of and chemically react with a much larger amount of CO2 from the air. The chemisorption capacity of CO2 in these pure and mixed systems is ordered as chitosan/[EMIM][Ac] mixture > chitin/[EMIM][Ac] mixture > cellulose/[EMIM][Ac] mixture > pure [EMIM][Ac] (ca. 0.09 mass ratio % g/g CO2/IL). (3) The CO2 solubility in [EMIM][Ac] decreases about 50% after being exposed to the atmospheric moist air for some specific time period.

  17. The dynamic process of atmospheric water sorption in [EMIM][Ac] and mixtures of [EMIM][Ac] with biopolymers and CO2 capture in these systems.

    PubMed

    Chen, Yu; Sun, Xiaofu; Yan, Chuanyu; Cao, Yuanyuan; Mu, Tiancheng

    2014-10-01

    There are mainly three findings related to the dynamic process of atmospheric water sorption in the ionic liquid (IL) 1-ethyl-3-methlyl-imidazolium acetate ([EMIM][Ac]) and its mixtures with biopolymers (i.e., cellulose, chitin, and chitosan), and CO2 capture in these systems above. The analytical methods mainly include gravimetric hygroscopicity measurement and in situ infrared spectroscopy with the techniques of difference, derivative, deconvoluted attenuated total reflectance and two-dimensional correlation. These three findings are listed as below. (1) Pure [EMIM][Ac] only shows a two-regime pattern, while all the mixtures of [EMIM][Ac] with biopolymers (i.e., cellulose, chitin, and chitosan) present a three-regime tendency for the dynamic process of atmospheric water sorption. Specifically, the IL/chitosan mixture has a clear three-regime mode; the [EMIM][Ac]/chitin mixture has an unclear indiscernible regime 3; and the [EMIM][Ac]/cellulose mixture shows an indiscernible regime 2. (2) [EMIM][Ac] and its mixtures with biopolymers could physically absorb a trace amount of and chemically react with a much larger amount of CO2 from the air. The chemisorption capacity of CO2 in these pure and mixed systems is ordered as chitosan/[EMIM][Ac] mixture > chitin/[EMIM][Ac] mixture > cellulose/[EMIM][Ac] mixture > pure [EMIM][Ac] (ca. 0.09 mass ratio % g/g CO2/IL). (3) The CO2 solubility in [EMIM][Ac] decreases about 50% after being exposed to the atmospheric moist air for some specific time period. PMID:25208304

  18. Mapping the conformational epitope of a neutralizing antibody (AcV1) directed against the AcMNPV GP64 protein

    SciTech Connect

    Zhou Jian; Blissard, Gary W. . E-mail: gwb1@cornell.edu

    2006-09-01

    The envelope glycoprotein GP64 of Autographa californica nucleopolyhedrovirus (AcMNPV) is necessary and sufficient for the acid-induced membrane fusion activity that is required for fusion of the budded virus (BV) envelope and the endosome membrane during virus entry. Infectivity of the budded virus (BV) is neutralized by AcV1, a monoclonal antibody (MAb) directed against GP64. Prior studies indicated that AcV1 recognizes a conformational epitope and does not inhibit virus attachment to the cell, but instead inhibits entry at a step following virus attachment. We found that AcV1 recognition of GP64 was lost upon exposure of GP64 to low pH (pH 4.5) and restored by returning GP64 to pH 6.2. In addition, the AcV1 epitope was lost upon denaturation of GP64 in SDS, but the AcV1 epitope was restored by refolding the protein in the absence of SDS. Using truncated GP64 proteins expressed in insect cells, we mapped the AcV1 epitope to a 24 amino acid region in the central variable domain of GP64. When sequences within the mapped AcV1 epitope were substituted with a c-Myc epitope and the resulting construct was used to replace wt GP64 in recombinant AcMNPV viruses, the modified GP64 protein appeared to function normally. However, an anti-c-Myc monoclonal antibody did not neutralize infectivity of those viruses. Because binding of the c-Myc MAb to the same site in the GP64 sequence did not result in neutralization, these studies suggest that AcV1 neutralization may result from a specific structural constraint caused by AcV1 binding and not simply by steric hindrance caused by antibody binding at this position in GP64.

  19. Early Function of the Abutilon Mosaic Virus AC2 Gene as a Replication Brake

    PubMed Central

    Krenz, Björn; Deuschle, Kathrin; Deigner, Tobias; Unseld, Sigrid; Kepp, Gabi; Wege, Christina; Kleinow, Tatjana

    2015-01-01

    ABSTRACT The C2/AC2 genes of monopartite/bipartite geminiviruses of the genera Begomovirus and Curtovirus encode important pathogenicity factors with multiple functions described so far. A novel function of Abutilon mosaic virus (AbMV) AC2 as a replication brake is described, utilizing transgenic plants with dimeric inserts of DNA B or with a reporter construct to express green fluorescent protein (GFP). Their replicational release upon AbMV superinfection or the individual and combined expression of epitope-tagged AbMV AC1, AC2, and AC3 was studied. In addition, the effects were compared in the presence and in the absence of an unrelated tombusvirus suppressor of silencing (P19). The results show that AC2 suppresses replication reproducibly in all assays and that AC3 counteracts this effect. Examination of the topoisomer distribution of supercoiled DNA, which indicates changes in the viral minichromosome structure, did not support any influence of AC2 on transcriptional gene silencing and DNA methylation. The geminiviral AC2 protein has been detected here for the first time in plants. The experiments revealed an extremely low level of AC2, which was slightly increased if constructs with an intron and a hemagglutinin (HA) tag in addition to P19 expression were used. AbMV AC2 properties are discussed with reference to those of other geminiviruses with respect to charge, modification, and size in order to delimit possible reasons for the different behaviors. IMPORTANCE The (A)C2 genes encode a key pathogenicity factor of begomoviruses and curtoviruses in the plant virus family Geminiviridae. This factor has been implicated in the resistance breaking observed in agricultural cotton production. AC2 is a multifunctional protein involved in transcriptional control, gene silencing, and regulation of basal biosynthesis. Here, a new function of Abutilon mosaic virus AC2 in replication control is added as a feature of this protein in viral multiplication, providing a novel

  20. Isolation of an acetyl-CoA synthetase gene (ZbACS2) from Zygosaccharomyces bailii.

    PubMed

    Rodrigues, Fernando; Zeeman, Anne-Marie; Cardoso, Helena; Sousa, Maria João; Steensma, H Yde; Côrte-Real, Manuela; Leão, Cecília

    2004-03-01

    A gene homologous to Saccharomyces cerevisiae ACS genes, coding for acetyl-CoA synthetase, has been cloned from the yeast Zygosaccharomyces bailii ISA 1307, by using reverse genetic approaches. A probe obtained by PCR amplification from Z. bailii DNA, using primers derived from two conserved regions of yeast ACS proteins, RIGAIHSVVF (ScAcs1p; 210-219) and RVDDVVNVSG (ScAcs1p; 574-583), was used for screening a Z. bailii genomic library. Nine clones with partially overlapping inserts were isolated. The sequenced DNA fragment contains a complete ORF of 2027 bp (ZbACS2) and the deduced polypeptide shares significant homologies with the products of ACS2 genes from S. cerevisiae and Kluyveromyces lactis (81% and 82% identity and 84% and 89% similarity, respectively). Phylogenetic analysis shows that the sequence of Zbacs2 is more closely related to the sequences from Acs2 than to those from Acs1 proteins. Moreover, this analysis revealed that the gene duplication producing Acs1 and Acs2 proteins has occurred in the common ancestor of S. cerevisiae, K. lactis, Candida albicans, C. glabrata and Debaryomyces hansenii lineages. Additionally, the cloned gene allowed growth of S. cerevisiae Scacs2 null mutant, in medium containing glucose as the only carbon and energy source, indicating that it encodes a functional acetyl-CoA synthetase. Also, S. cerevisiae cells expressing ZbACS2 have a shorter lag time, in medium containing glucose (2%, w/v) plus acetic acid (0.1-0.35%, v/v). No differences in cell response to acetic acid stress were detected both by specific growth and death rates. The mode of regulation of ZbACS2 appears to be different from ScACS2 and KlACS2, being subject to repression by a glucose pulse in acetic acid-grown cells. PMID:15042592

  1. Detecting adaptive evolution and functional divergence in aminocyclopropane-1-carboxylate synthase (ACS) gene family.

    PubMed

    Zhang, Ti-Cao; Qiao, Qin; Zhong, Yang

    2012-06-01

    Ethylene is an essential plant gaseous hormone that controls many aspects of plant growth and development, especially the fruit ripening. It is important to know how this hormone is synthesized and how its production is regulated to understand the roles of ethylene in plant development. The aminocyclopropane-1-carboxylate synthase (ACS) gene is a rate-limiting enzyme in the ethylene biosynthesis pathway, which is encoded by a highly divergent multi-gene family in plant species. Although many ACS genes have been cloned from a wide variety of plant species previously, their origin and evolutionary process are still not clear. In this study, we conducted a phylogenetic analysis based on an updated dataset including 107 members of plant ACS genes and eight ACS-like genes from animal as well as six AATase genes. The motifs were identified and the positive selection and functional divergence in the ACS gene family were detected. The results obtained from these analyses are consistent with previous division of the ACS gene family in angiosperm, i.e., three distinct clades, and show that the duplications of three subclades (I, II and III) ACS genes have occurred after the divergence of gymnosperm and angiosperm. We conclude that the ACS genes could have experienced three times significant positive selection as they underwent expansion in land plants and gain the full-scale ethylene biosynthesis and regulatory functions, and all plant ACS genes originated from plant-ACS-like genes which come from AATase genes.

  2. A type III ACC synthase, ACS7, is involved in root gravitropism in Arabidopsis thaliana

    PubMed Central

    Chang, Ing-Feng

    2013-01-01

    Ethylene is an important plant hormone that regulates developmental processes in plants. The ethylene biosynthesis pathway is a highly regulated process at both the transcriptional and post-translational level. The transcriptional regulation of these ethylene biosynthesis genes is well known. However, post-translational modifications of the key ethylene biosynthesis enzyme 1-aminocyclopropane-1-carboxylate (ACC) synthase (ACS) are little understood. In vitro kinase assays were conducted on the type III ACS, AtACS7, fusion protein and peptides to determine whether the AtACS7 protein can be phosphorylated by calcium-dependent protein kinase (CDPK). AtACS7 was phosphorylated at Ser216, Thr296, and Ser299 by AtCDPK16 in vitro. To investigate further the function of the ACS7 gene in Arabidopsis, an acs7-1 loss-of-function mutant was isolated. The acs7-1 mutant exhibited less sensitivity to the inhibition of root gravitropism by treatment with the calcium chelator ethylene glycol tetraacetic acid (EGTA). Seedlings were treated with gradient concentrations of ACC. The results showed that a certain concentration of ethylene enhanced the gravity response. Moreover, the acs7-1 mutant was less sensitive to inhibition of the gravity response by treatment with the auxin polar transport inhibitor 1-naphthylphthalamic acid, but exogenous ACC application recovered root gravitropism. Altogether, the results indicate that AtACS7 is involved in root gravitropism in a calcium-dependent manner in Arabidopsis. PMID:23943848

  3. Concurrent Electroencephalography Recording During Transcranial Alternating Current Stimulation (tACS)

    PubMed Central

    Fehér, Kristoffer D.; Morishima, Yosuke

    2016-01-01

    Oscillatory brain activities are considered to reflect the basis of rhythmic changes in transmission efficacy across brain networks and are assumed to integrate cognitive neural processes. Transcranial alternating current stimulation (tACS) holds the promise to elucidate the causal link between specific frequencies of oscillatory brain activity and cognitive processes. Simultaneous electroencephalography (EEG) recording during tACS would offer an opportunity to directly explore immediate neurophysiological effects of tACS. However, it is not trivial to measure EEG signals during tACS, as tACS creates a huge artifact in EEG data. Here we explain how to set up concurrent tACS-EEG experiments. Two necessary considerations for successful EEG recording while applying tACS are highlighted. First, bridging of the tACS and EEG electrodes via leaking EEG gel immediately saturates the EEG amplifier. To avoid bridging via gel, the viscosity of the EEG gel is the most important parameter. The EEG gel must be viscous to avoid bridging, but at the same time sufficiently fluid to create contact between the tACS electrode and the scalp. Second, due to the large amplitude of the tACS artifact, it is important to consider using an EEG system with a high resolution analog-to-digital (A/D) converter. In particular, the magnitude of the tACS artifact can exceed 100 mV at the vicinity of a stimulation electrode when 1 mA tACS is applied. The resolution of the A/D converter is of importance to measure good quality EEG data from the vicinity of the stimulation site. By following these guidelines for the procedures and technical considerations, successful concurrent EEG recording during tACS will be realized. PMID:26862814

  4. Power Electronic Transformer based Three-Phase PWM AC Drives

    NASA Astrophysics Data System (ADS)

    Basu, Kaushik

    A Transformer is used to provide galvanic isolation and to connect systems at different voltage levels. It is one of the largest and most expensive component in most of the high voltage and high power systems. Its size is inversely proportional to the operating frequency. The central idea behind a power electronic transformer (PET) also known as solid state transformer is to reduce the size of the transformer by increasing the frequency. Power electronic converters are used to change the frequency of operation. Steady reduction in the cost of the semiconductor switches and the advent of advanced magnetic materials with very low loss density and high saturation flux density implies economic viability and feasibility of a design with high power density. Application of PET is in generation of power from renewable energy sources, especially wind and solar. Other important application include grid tied inverters, UPS e.t.c. In this thesis non-resonant, single stage, bi-directional PET is considered. The main objective of this converter is to generate adjustable speed and magnitude pulse width modulated (PWM) ac waveforms from an ac or dc grid with a high frequency ac link. The windings of a high frequency transformer contains leakage inductance. Any switching transition of the power electronic converter connecting the inductive load and the transformer requires commutation of leakage energy. Commutation by passive means results in power loss, decrease in the frequency of operation, distortion in the output voltage waveform, reduction in reliability and power density. In this work a source based partially loss-less commutation of leakage energy has been proposed. This technique also results in partial soft-switching. A series of converters with novel PWM strategies have been proposed to minimize the frequency of leakage inductance commutation. These PETs achieve most of the important features of modern PWM ac drives including 1) Input power factor correction, 2) Common

  5. A PWM transistor inverter for an ac electric vehicle drive

    NASA Technical Reports Server (NTRS)

    Slicker, J. M.

    1981-01-01

    A prototype system consisting of closely integrated motor, inverter, and transaxle has been built in order to demonstrate the feasibility of a three-phase ac transistorized inverter for electric vehicle applications. The microprocessor-controlled inverter employs monolithic power transistors to drive an oil-cooled, three-phase induction traction motor at a peak output power of 30 kW from a 144 V battery pack. Transistor safe switching requirements are discussed, and a circuit is presented for recovering trapped snubber inductor energy at transistor turn-off.

  6. Atomic Mass and Nuclear Binding Energy for Ac-272 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-272 (Actinium, atomic number Z = 89, mass number A = 272).

  7. Atomic Mass and Nuclear Binding Energy for Ac-295 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-295 (Actinium, atomic number Z = 89, mass number A = 295).

  8. Atomic Mass and Nuclear Binding Energy for Ac-234 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-234 (Actinium, atomic number Z = 89, mass number A = 234).

  9. Atomic Mass and Nuclear Binding Energy for Ac-273 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-273 (Actinium, atomic number Z = 89, mass number A = 273).

  10. Atomic Mass and Nuclear Binding Energy for Ac-242 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-242 (Actinium, atomic number Z = 89, mass number A = 242).

  11. Atomic Mass and Nuclear Binding Energy for Ac-251 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-251 (Actinium, atomic number Z = 89, mass number A = 251).

  12. Atomic Mass and Nuclear Binding Energy for Ac-285 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-285 (Actinium, atomic number Z = 89, mass number A = 285).

  13. Atomic Mass and Nuclear Binding Energy for Ac-278 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-278 (Actinium, atomic number Z = 89, mass number A = 278).

  14. Atomic Mass and Nuclear Binding Energy for Ac-226 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-226 (Actinium, atomic number Z = 89, mass number A = 226).

  15. Atomic Mass and Nuclear Binding Energy for Ac-270 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-270 (Actinium, atomic number Z = 89, mass number A = 270).

  16. Atomic Mass and Nuclear Binding Energy for Ac-245 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-245 (Actinium, atomic number Z = 89, mass number A = 245).

  17. Atomic Mass and Nuclear Binding Energy for Ac-279 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-279 (Actinium, atomic number Z = 89, mass number A = 279).

  18. Atomic Mass and Nuclear Binding Energy for Ac-243 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-243 (Actinium, atomic number Z = 89, mass number A = 243).

  19. Atomic Mass and Nuclear Binding Energy for Ac-257 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-257 (Actinium, atomic number Z = 89, mass number A = 257).

  20. Atomic Mass and Nuclear Binding Energy for Ac-293 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-293 (Actinium, atomic number Z = 89, mass number A = 293).

  1. Atomic Mass and Nuclear Binding Energy for Ac-259 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-259 (Actinium, atomic number Z = 89, mass number A = 259).

  2. Atomic Mass and Nuclear Binding Energy for Ac-274 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-274 (Actinium, atomic number Z = 89, mass number A = 274).

  3. Atomic Mass and Nuclear Binding Energy for Ac-225 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-225 (Actinium, atomic number Z = 89, mass number A = 225).

  4. Atomic Mass and Nuclear Binding Energy for Ac-282 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-282 (Actinium, atomic number Z = 89, mass number A = 282).

  5. Atomic Mass and Nuclear Binding Energy for Ac-229 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-229 (Actinium, atomic number Z = 89, mass number A = 229).

  6. Atomic Mass and Nuclear Binding Energy for Ac-292 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-292 (Actinium, atomic number Z = 89, mass number A = 292).

  7. Atomic Mass and Nuclear Binding Energy for Ac-238 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-238 (Actinium, atomic number Z = 89, mass number A = 238).

  8. Atomic Mass and Nuclear Binding Energy for Ac-227 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-227 (Actinium, atomic number Z = 89, mass number A = 227).

  9. Atomic Mass and Nuclear Binding Energy for Ac-247 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-247 (Actinium, atomic number Z = 89, mass number A = 247).

  10. Atomic Mass and Nuclear Binding Energy for Ac-231 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-231 (Actinium, atomic number Z = 89, mass number A = 231).

  11. Atomic Mass and Nuclear Binding Energy for Ac-287 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-287 (Actinium, atomic number Z = 89, mass number A = 287).

  12. Atomic Mass and Nuclear Binding Energy for Ac-232 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-232 (Actinium, atomic number Z = 89, mass number A = 232).

  13. Atomic Mass and Nuclear Binding Energy for Ac-244 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-244 (Actinium, atomic number Z = 89, mass number A = 244).

  14. Atomic Mass and Nuclear Binding Energy for Ac-241 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-241 (Actinium, atomic number Z = 89, mass number A = 241).

  15. Atomic Mass and Nuclear Binding Energy for Ac-277 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-277 (Actinium, atomic number Z = 89, mass number A = 277).

  16. Atomic Mass and Nuclear Binding Energy for Ac-252 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-252 (Actinium, atomic number Z = 89, mass number A = 252).

  17. Atomic Mass and Nuclear Binding Energy for Ac-264 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-264 (Actinium, atomic number Z = 89, mass number A = 264).

  18. Atomic Mass and Nuclear Binding Energy for Ac-265 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-265 (Actinium, atomic number Z = 89, mass number A = 265).

  19. Atomic Mass and Nuclear Binding Energy for Ac-230 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-230 (Actinium, atomic number Z = 89, mass number A = 230).

  20. Atomic Mass and Nuclear Binding Energy for Ac-256 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-256 (Actinium, atomic number Z = 89, mass number A = 256).

  1. Atomic Mass and Nuclear Binding Energy for Ac-289 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-289 (Actinium, atomic number Z = 89, mass number A = 289).

  2. Atomic Mass and Nuclear Binding Energy for Ac-268 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-268 (Actinium, atomic number Z = 89, mass number A = 268).

  3. Atomic Mass and Nuclear Binding Energy for Ac-235 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-235 (Actinium, atomic number Z = 89, mass number A = 235).

  4. Atomic Mass and Nuclear Binding Energy for Ac-228 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-228 (Actinium, atomic number Z = 89, mass number A = 228).

  5. Atomic Mass and Nuclear Binding Energy for Ac-290 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-290 (Actinium, atomic number Z = 89, mass number A = 290).

  6. Atomic Mass and Nuclear Binding Energy for Ac-223 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-223 (Actinium, atomic number Z = 89, mass number A = 223).

  7. Atomic Mass and Nuclear Binding Energy for Ac-288 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-288 (Actinium, atomic number Z = 89, mass number A = 288).

  8. Atomic Mass and Nuclear Binding Energy for Ac-275 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-275 (Actinium, atomic number Z = 89, mass number A = 275).

  9. Atomic Mass and Nuclear Binding Energy for Ac-237 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-237 (Actinium, atomic number Z = 89, mass number A = 237).

  10. Atomic Mass and Nuclear Binding Energy for Ac-224 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-224 (Actinium, atomic number Z = 89, mass number A = 224).

  11. Atomic Mass and Nuclear Binding Energy for Ac-250 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-250 (Actinium, atomic number Z = 89, mass number A = 250).

  12. Atomic Mass and Nuclear Binding Energy for Ac-249 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-249 (Actinium, atomic number Z = 89, mass number A = 249).

  13. Atomic Mass and Nuclear Binding Energy for Ac-262 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-262 (Actinium, atomic number Z = 89, mass number A = 262).

  14. Atomic Mass and Nuclear Binding Energy for Ac-258 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-258 (Actinium, atomic number Z = 89, mass number A = 258).

  15. Atomic Mass and Nuclear Binding Energy for Ac-281 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-281 (Actinium, atomic number Z = 89, mass number A = 281).

  16. Atomic Mass and Nuclear Binding Energy for Ac-294 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-294 (Actinium, atomic number Z = 89, mass number A = 294).

  17. Atomic Mass and Nuclear Binding Energy for Ac-240 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-240 (Actinium, atomic number Z = 89, mass number A = 240).

  18. Atomic Mass and Nuclear Binding Energy for Ac-253 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-253 (Actinium, atomic number Z = 89, mass number A = 253).

  19. Atomic Mass and Nuclear Binding Energy for Ac-280 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-280 (Actinium, atomic number Z = 89, mass number A = 280).

  20. Atomic Mass and Nuclear Binding Energy for Ac-291 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-291 (Actinium, atomic number Z = 89, mass number A = 291).

  1. Atomic Mass and Nuclear Binding Energy for Ac-269 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-269 (Actinium, atomic number Z = 89, mass number A = 269).

  2. Atomic Mass and Nuclear Binding Energy for Ac-266 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-266 (Actinium, atomic number Z = 89, mass number A = 266).

  3. Atomic Mass and Nuclear Binding Energy for Ac-263 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-263 (Actinium, atomic number Z = 89, mass number A = 263).

  4. Atomic Mass and Nuclear Binding Energy for Ac-283 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-283 (Actinium, atomic number Z = 89, mass number A = 283).

  5. Atomic Mass and Nuclear Binding Energy for Ac-286 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-286 (Actinium, atomic number Z = 89, mass number A = 286).

  6. Atomic Mass and Nuclear Binding Energy for Ac-261 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-261 (Actinium, atomic number Z = 89, mass number A = 261).

  7. Atomic Mass and Nuclear Binding Energy for Ac-236 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-236 (Actinium, atomic number Z = 89, mass number A = 236).

  8. Atomic Mass and Nuclear Binding Energy for Ac-239 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-239 (Actinium, atomic number Z = 89, mass number A = 239).

  9. Atomic Mass and Nuclear Binding Energy for Ac-246 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-246 (Actinium, atomic number Z = 89, mass number A = 246).

  10. Atomic Mass and Nuclear Binding Energy for Ac-271 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-271 (Actinium, atomic number Z = 89, mass number A = 271).

  11. Atomic Mass and Nuclear Binding Energy for Ac-260 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-260 (Actinium, atomic number Z = 89, mass number A = 260).

  12. Atomic Mass and Nuclear Binding Energy for Ac-248 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-248 (Actinium, atomic number Z = 89, mass number A = 248).

  13. Atomic Mass and Nuclear Binding Energy for Ac-255 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-255 (Actinium, atomic number Z = 89, mass number A = 255).

  14. Atomic Mass and Nuclear Binding Energy for Ac-276 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-276 (Actinium, atomic number Z = 89, mass number A = 276).

  15. Atomic Mass and Nuclear Binding Energy for Ac-233 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-233 (Actinium, atomic number Z = 89, mass number A = 233).

  16. Atomic Mass and Nuclear Binding Energy for Ac-284 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-284 (Actinium, atomic number Z = 89, mass number A = 284).

  17. Atomic Mass and Nuclear Binding Energy for Ac-254 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-254 (Actinium, atomic number Z = 89, mass number A = 254).

  18. Atomic Mass and Nuclear Binding Energy for Ac-267 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-267 (Actinium, atomic number Z = 89, mass number A = 267).

  19. Topological Instabilities in ac-Driven Bosonic Systems.

    PubMed

    Engelhardt, G; Benito, M; Platero, G; Brandes, T

    2016-07-22

    Under nonequilibrium conditions, bosonic modes can become dynamically unstable with an exponentially growing occupation. On the other hand, topological band structures give rise to symmetry protected midgap states. In this Letter, we investigate the interplay of instability and topology. Thereby, we establish a general relation between topology and instability under ac driving. We apply our findings to create dynamical instabilities which are strongly localized at the boundaries of a finite-size system. As these localized instabilities are protected by symmetry, they can be considered as topological instabilities. PMID:27494478

  20. Lipid Bilayer Vesicle Dynamics in AC Electric Fields

    NASA Astrophysics Data System (ADS)

    McConnell, Lane; Vlahovska, Petia; Miksis, Michael

    2014-11-01

    Vesicles are closed, fluid-filled lipid bilayers which are mechanically similar to biological cells and which undergo shape transitions in the presence of electric fields. Here we model the vesicle membrane as an infinitely thin, capacitive, area-incompressible interface with the surrounding fluids acting as charge-advecting leaky dielectrics. We then implement the boundary integral method to numerically investigate the dynamics of a vesicle in various AC electric field profiles. Our numerical results are then compared with recent small deformation theory and experimental data. We also note our observation of a new theoretical vesicle behavior that has yet to be observed experimentally.

  1. Atomic Mass and Nuclear Binding Energy for Ac-222 (Actinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Ac-222 (Actinium, atomic number Z = 89, mass number A = 222).

  2. dc-to-ac power converter for fuel cell system

    SciTech Connect

    Kawabata, T.; Asaeda, T.; Hamasaki, Y.; Yutani, T.

    1983-10-01

    As the interface between fuel cells and the utility line, a self-commutated inverter is preferred to a line-commutated inverter because of its easy controllability. Using the gate turn off (GTO) thyristors, this inverter can have high efficiency and simple circuit configurations. This paper describes the design features and test results of the dc-to-ac power converter, which is principally composed of four-phase transistor chopper and 12-pulse GTO inverter, for a 50kW experimental fuel cell power system. Furthermore, new GTO inverter which improves the circuit efficiency is presented. Special emphasis is placed on a detailed analysis and evaluation of this GTO inverter.

  3. An ac microcalorimeter employing a diode laser as a heater

    NASA Astrophysics Data System (ADS)

    Marone, M. J.; Payne, J. E.

    1997-12-01

    We have built an ac microcalorimeter which uses a diode laser as the heater. The absence of a contact heater reduces the total addendum. This method has several advantages over the typical quartz lamp and mechanical chopper wheel configuration. The laser is modulated by a lock-in amplifier which provides a wider choice of operating frequencies, typically from 0.2 to 50 Hz. The microcalorimeter has been used from near room temperature to 5 K. Single-crystal samples of YBCO with a mass as small as 4 μg have been measured. The device is particularly useful in the study of whiskers and other very small samples.

  4. Complex Calorimeter with AC- and Relaxation-Mode Operation

    NASA Astrophysics Data System (ADS)

    Ema, Kenji; Uematsu, Takashi; Sugata, Atsushi; Yao, Haruhiko

    1993-04-01

    A complex calorimeter has been developed. This calorimeter, which can be operated both in the ac mode and the relaxation mode using the same sample cell and the same apparatus settings, uses only a small amount (30-50 mg) of sample. An application to measurements in the vicinity of the antiferroelectric phase transitions in the liquid crystal MHPOBC(4-(1-methylheptyloxycarbonyl)-phenyl 4'-octyloxybiphenyl-4-carboxylate) is demonstrated. It is shown that the present calorimeter, when operated in the relaxation mode, enables detection of the latent heat with a resolution of 0.002 J/g.

  5. The ac Josephson effect: observation of electromagnetic radiation (Review)

    NASA Astrophysics Data System (ADS)

    Yanson, I. K.

    2004-07-01

    An historical review of the discovery and the early period of research on the Josephson effect is given. Experiments on the tunneling effect in superconductors done in the 1960s at the Institute for Low Temperature Physics and Engineering of the National Academy of Sciences of Ukraine, Kharkov (ILTPE), which led to the observation of Josephson electromagnetic radiation are described in detail. The experimental data are illustrated by the original curves, and the dates they were taken are indicated. The physical mechanism for the generation of rf radiation in superconducting tunnel junctions is examined, and some of the more promising applications of the ac Josephson effect are briefly listed.

  6. Topological Instabilities in ac-Driven Bosonic Systems

    NASA Astrophysics Data System (ADS)

    Engelhardt, G.; Benito, M.; Platero, G.; Brandes, T.

    2016-07-01

    Under nonequilibrium conditions, bosonic modes can become dynamically unstable with an exponentially growing occupation. On the other hand, topological band structures give rise to symmetry protected midgap states. In this Letter, we investigate the interplay of instability and topology. Thereby, we establish a general relation between topology and instability under ac driving. We apply our findings to create dynamical instabilities which are strongly localized at the boundaries of a finite-size system. As these localized instabilities are protected by symmetry, they can be considered as topological instabilities.

  7. Fast recovery, high voltage silicon diodes for AC motor controllers

    NASA Technical Reports Server (NTRS)

    Balodis, V.; Berman, A. H.; Gaugh, C.

    1982-01-01

    The fabrication and characterization of a high voltage, high current, fast recovery silicon diode for use in AC motor controllers, originally developed for NASA for use in avionics power supplies, is presented. The diode utilizes a positive bevel PIN mesa structure with glass passivation and has the following characteristics: peak inverse voltage - 1200 volts, forward voltage at 50 amperes - 1.5 volts, reverse recovery time of 200 nanoseconds. Characterization data for the diode, included in a table, show agreement with design concepts developed for power diodes. Circuit diagrams of the diode are also given.

  8. STIS-ACS Red Leak Cross-Calibration

    NASA Astrophysics Data System (ADS)

    Chiaberge, Marco

    2009-07-01

    We observe one type K star {G Gem} with ACS/SBC and STIS in order to determine the throughput in the red leak of both the SBC and the STIS FUV-MAMA. We will also observe the type G9V star HD53143 with the SBC with all long-pass filters and the PR130L in order to compare the observed fluxes and the spectrum with a previous prism observation of the same star and investigate the possible time dependence of the red leak.

  9. Glutathione preconditioning attenuates Ac-LDL-induced macrophage apoptosis via protein kinase C-dependent Ac-LDL trafficking.

    PubMed

    Rosenson-Schloss, Rene S; Chnari, Evangelia; Brieva, Thomas A; Dang, Anh; Moghe, Prabhas V

    2005-01-01

    Oxidized low-density lipoprotein (ox-LDL) incorporation into intimally resident vascular cells via scavenger receptors marks one of the early steps in atherosclerosis. Cellular apoptotic damage results from two major serial intracellular events: the binding and scavenger receptor-mediated uptake of oxidizable lipoproteins and the intracellular oxidative responses of accumulated lipoproteins. Most molecular approaches to prevent apoptotic damage have focused on singular events within the cascade of lipoprotein trafficking. To identify a multifocal strategy against LDL-induced apoptosis, we evaluated the role of cellular preconditioning by glutathione-ethyl ester (GSH-Et), a native redox regulator, in the prevention of the uptake and apoptotic effects of an oxidizable scavenger receptor-specific ligand, acetylated low-density lipoprotein (Ac-LDL). Our results indicate that GSH-Et-mediated protein kinase C (PKC) pathway modulation regulates Ac-LDL binding and incorporation into GSH-Et preconditioned cells and subsequently delays reactive oxygen intermediate generation and apoptotic conversion. The GSH-Et protective effects on apoptosis and Ac-LDL binding were reversed by calphostin C, a PKC inhibitor, and were accompanied by an increase in PKC phosphorylation. However, the rate of reactive oxygen intermediate accumulation was not increased following calphostin C treatment, suggesting that GSH-Et may play an important nonreactive oxygen-intermediate-based protective role in regulating apoptotic dynamics. Overall, we report on the novel role for GSH-Et preconditioning as a molecular strategy to limit lipoprotein entry into the cells, which presents a proactive modality to prevent cellular apoptosis in contrast with the prevalent antioxidant approaches that treat damage retroactively. PMID:15618124

  10. System and method for determining stator winding resistance in an AC motor

    DOEpatents

    Lu, Bin; Habetler, Thomas G.; Zhang, Pinjia; Theisen, Peter J.

    2011-05-31

    A system and method for determining stator winding resistance in an AC motor is disclosed. The system includes a circuit having an input connectable to an AC source and an output connectable to an input terminal of an AC motor. The circuit includes at least one contactor and at least one switch to control current flow and terminal voltages in the AC motor. The system also includes a controller connected to the circuit and configured to modify a switching time of the at least one switch to create a DC component in an output of the system corresponding to an input to the AC motor and determine a stator winding resistance of the AC motor based on the injected DC component of the voltage and current.

  11. Ac vortex-dependent torsional oscillation response and onset temperature T0 in solid 4He.

    PubMed

    Penzev, Andrey; Yasuta, Yoshinori; Kubota, Minoru

    2008-08-01

    Detailed studies of ac velocity V_{ac} and T dependence of torsional oscillator responses of solid 4He are reported. A characteristic onset temperature T_{0} approximately 0.5 K is found, below which a significant V_{ac}-dependent change occurs in the energy dissipation for the samples at approximately 32 bar and for one at 49 bar. A V_{ac} dependence of the so-called "nonclassical rotational inertia" fraction also appears below approximately T_{0}. The log(V_{ac}) linear dependence, which suggests involvement of quantized vorticies, was examined in the nonclassical rotational inertia fraction. We find a common 1/T;{2} dependence for this linear slope change in all of the samples for 30ac}<300 microm/s. We discuss that our observation is consistent with nonlinear rotational susceptibility of the vortex fluid, proposed by Anderson above T_{c} below T0. PMID:18764467

  12. Resonant tunneling of interacting electrons in an AC electric field

    SciTech Connect

    Elesin, V. F.

    2013-11-15

    The problem of the effect of electron-electron interaction on the static and dynamic properties of a double-barrier nanostructure (resonant tunneling diode (RTD)) is studied in terms of a coherent tunneling model, which includes a set of Schrödinger and Poisson equations with open boundary conditions. Explicit analytical expressions are derived for dc and ac potentials and reduced (active and reactive) currents in the quasi-classical approximation over a wide frequency range. These expressions are used to analyze the frequency characteristics of RTD. It is shown that the interaction can radically change the form of these expressions, especially in the case of a hysteretic I-V characteristic. In this case, the active current and the ac potentials can increase sharply at both low and high frequencies. For this increase to occur, it is necessary to meet quantum regime conditions and to choose a proper working point in the I-V characteristic of RTD. The possibility of appearance of specific plasma oscillations, which can improve the high-frequency characteristics of RTD, is predicted. It is found that the active current can be comparable with the resonant dc current of RTD.

  13. Mechanism for AC Electric Field Deflection of Flames

    NASA Astrophysics Data System (ADS)

    Chemama, Michael; Bishop, Kyle; Cademartiri, Ludovico; Brenner, Michael P.; Whitesides, Georges M.

    2010-11-01

    Effects of electric fields on flames have been observed and studied since the 19th century. It is well known that the presence of an electric field can modify the shape of a burner or candle-like diffusion flame. Most experimental observations and theoretical analyses focused on DC fields. Recent experiments show that a flame can also be bent and even put out by an AC field. To explain how a zero time average cause can give rise to a net effect on the flame we develop a perturbation theory of the combustion equations modified to allow for the presence of the field and completed by Maxwell's equation. Theoretical and numerical analyses of the equations indeed show that the AC field creates a force whose magnitude is comparable to gravity for high enough fields (1e5 V/m). The dependency of this critical field on the frequency and the effect on the flame shape are also obtained and compared to experimental results.

  14. ACS after SM4: New Life for an Old Workhorse

    NASA Astrophysics Data System (ADS)

    Golimowski, David; Anderson, Jay; Armstrong, Amber; Arslanian, Steve; Bedin, Luigi; Bohlin, Ralph; Boyce, Kevin; Chapman, George; Cheng, Edward; Chiaberge, Marco; Cox, Colin; Desiardins, Tyler; Dye, Darryl; Ellis, Tracy; Ferguson, Brian; Fruchter, Andrew; Grogin, Norman; Lim, Pey Lian; Loose, Markus; Lucas, Ray; Lupie, Olivia; Mack, Jennifer; Maybhate, Aparna; Mil, Kathleen; Mutchler, Max; Ricardo, Raphael; Scott, Barbara; Serrano, Beverly; Sirianni, Marco; Smith, Linda; Suchkov, Anatoly A.; Waczynski, Augustyn; Welty, Alan; Wheeler, Thomas; Wilson, Erin

    2010-07-01

    The ACS CCD Electronics Box Replacement (CEB-R) installed during SM4 features a Teledyne SIDECAR ASIC that permits optimization of the WFC via adjustment of CCD clock voltages, bias voltages, and pixel transmission timing. An on-orbit campaign to optimize the performance of the WFC was undertaken at the start of the SMOV period. Initial tests with pre-SM4 default voltages and timing patterns showed that WFC's performance matches or exceeds its pre-failure levels, notwithstanding the expected increases in dark current and hot pixels and the decline in charge-transfer efficiency due to prolonged exposure to HST's radiation environment. One WFC CCD exhibited anomalous behavior when operated with nondefault settings of its reset drain voltage. Consequently, the optimization campaign was truncated after two iterations, and ACS science operations commenced with the pre-SM4 default configuration. Several artifacts attributed to the CEB-R appear in post-SM4 WFC images: large-scale but stable bias gradients, low-level but temporally variable horizontal stripes, a signal-dependent bias shift, and amplifier crosstalk. STScI has developed algorithms for the correction or mitigation of these electronic artifacts as well as for the restoration of images affected by continuously degrading CTE. Standalone correction packages are now or will soon be publicly available. These packages will be incorporated into the calacs package of the OPUS data pipeline by September 2011.

  15. ACS after Servicing Mission 4: The WFC Optimization Campaign

    NASA Astrophysics Data System (ADS)

    Golimowski, David; Cheng, Ed; Loose, Markus; Sirianni, Marco; Lupie, Olivia; Smith, Linda; Arslanian, Steve; Boyce, Kevin; Chapman, George; Chiaberge, Marco; Desjardins, Tyler; Dye, Darryl; Grogin, Norman; Lim, Pey Lian; Lucas, Ray; Maybhate, Aparna; Mil, Kathleen; Mutchler, Max; Ricardo, Raphael; Scott, Barbara; Serrano, Beverly; Suchkov, Anatoly; Waczynski, Augustyn; Welty, Alan; Wheeler, Thomas; Wilson, Erin

    2011-07-01

    The ACS CCD Electronics Box Replacement (CEB-R) installed during SM4 features a Teledyne SIDECAR ASIC that permits optimization of the WFC via adjustment of CCD clock voltages, bias voltages, and pixel transmission timing. A built-in oscilloscope mode allows sensing of the analog signal from each output amplifier. An on-orbit campaign to optimize the performance of the WFC was undertaken at the start of the SMOV period. Initial tests with pre-SM4 default voltages and timing patterns showed that WFC's performance matches or exceeds its pre-failure levels, notwithstanding the expected increases in dark current and hot pixels and the decline in charge-transfer efficiency due to prolonged exposure to HST's radiation environment. The WFC2 CCD exhibited anomalous behavior when operated with nondefault settings of its amplifiers' reset-drain voltage (VOD). The CCD again displayed normal behavior when VOD was restored to its default setting. Consequently, the Optimization Campaign was truncated after two iterations, and ACS science operations commenced with the pre-SM4 default configuration.

  16. Input current shaped ac-to-dc converters

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Input current shaping techniques for ac-to-dc converters were investigated. Input frequencies much higher than normal, up to 20 kHz were emphasized. Several methods of shaping the input current waveform in ac-to-dc converters were reviewed. The simplest method is the LC filter following the rectifier. The next simplest method is the resistor emulation approach in which the inductor size is determined by the converter switching frequency and not by the line input frequency. Other methods require complicated switch drive algorithms to construct the input current waveshape. For a high-frequency line input, on the order of 20 kHz, the simple LC cannot be discarded so peremptorily, since the inductor size can be compared with that for the resistor emulation method. In fact, since a dc regulator will normally be required after the filter anyway, the total component count is almost the same as for the resistor emulation method, in which the filter is effectively incorporated into the regulator.

  17. ACS sampling system: design, implementation, and performance evaluation

    NASA Astrophysics Data System (ADS)

    Di Marcantonio, Paolo; Cirami, Roberto; Chiozzi, Gianluca

    2004-09-01

    By means of ACS (ALMA Common Software) framework we designed and implemented a sampling system which allows sampling of every Characteristic Component Property with a specific, user-defined, sustained frequency limited only by the hardware. Collected data are sent to various clients (one or more Java plotting widgets, a dedicated GUI or a COTS application) using the ACS/CORBA Notification Channel. The data transport is optimized: samples are cached locally and sent in packets with a lower and user-defined frequency to keep network load under control. Simultaneous sampling of the Properties of different Components is also possible. Together with the design and implementation issues we present the performance of the sampling system evaluated on two different platforms: on a VME based system using VxWorks RTOS (currently adopted by ALMA) and on a PC/104+ embedded platform using Red Hat 9 Linux operating system. The PC/104+ solution offers, as an alternative, a low cost PC compatible hardware environment with free and open operating system.

  18. Microfluidic flow-focusing in ac electric fields.

    PubMed

    Tan, Say Hwa; Semin, Benoît; Baret, Jean-Christophe

    2014-03-21

    We demonstrate the control of droplet sizes by an ac voltage applied across microelectrodes patterned around a flow-focusing junction. The electrodes do not come in contact with the fluids to avoid electrochemical effects. We found several regimes of droplet production in electric fields, controlled by the connection of the chip, the conductivity of the dispersed phase and the frequency of the applied field. A simple electrical modelling of the chip reveals that the effective voltage at the tip of the liquid to be dispersed controls the production mechanism. At low voltages (≲ 600 V), droplets are produced in dripping regime; the droplet size is a function of the ac electric field. The introduction of an effective capillary number that takes into account the Maxwell stress can explain the dependance of droplet size with the applied voltage. At higher voltages (≳ 600 V), jets are observed. The stability of droplet production is a function of the fluid conductivity and applied field frequency reported in a set of flow diagrams. PMID:24401868

  19. Revisiting the Mode-Beating Model of AC Helicity Injection

    NASA Astrophysics Data System (ADS)

    Sauppe, J. P.; Sovinec, C. R.

    2010-11-01

    Oscillating field current drive (OFCD), or AC helicity injection, is an important candidate for current sustainment in reversed-field pinch devices. Bellan examined AC helicity injection in a slab geometry and described it as a beating between two plasma modes that produces a mean current parallel to the equilibrium magnetic field [P. M. Bellan. Phys. Rev. Lett. 54, 1381 (1985)]. This mean current is confined to within a classical resistive skin depth of the plasma surface, and plasma relaxation is responsible for transporting this current to the core. We revisit this analytical work and examine how this wave-beating effect is represented in zero-beta MHD simulations, including consideration of the choice of boundary conditions. In addition to the expected parallel current, numerical simulations show a pinch effect from a cycle-averaged current that is perpendicular to the mean magnetic field, which is not described in Bellan's original work. Our results are discussed with respect to Boozer's general anti-dynamo theorem [A. H. Boozer. Phys. Fluids B Vol. 5, 2271 (1993)].

  20. Long-range response in ac electricity grids.

    PubMed

    Jung, Daniel; Kettemann, Stefan

    2016-07-01

    Local changes in the topology of electricity grids can cause overloads far away from the disturbance [D. Witthaut and M. Timme, Eur. Phys. J. B 86, 377 (2013)EPJBFY1434-602810.1140/epjb/e2013-40469-4], making the prediction of the robustness against changes in the topology-for example, caused by power outages or grid extensions-a challenging task. The impact of single-line additions on the long-range response of dc electricity grids has recently been studied [D. Labavić, R. Suciu, H. Meyer-Ortmanns, and S. Kettemann, Eur. Phys. J.: Spec. Top. 223, 2517 (2014)1951-635510.1140/epjst/e2014-02273-0]. By solving the real part of the static ac load flow equations, we conduct a similar investigation for ac grids. In a regular two-dimensional grid graph with cyclic boundary conditions, we find a power law decay for the change of power flow as a function of distance to the disturbance over a wide range of distances. The power exponent increases and saturates for large system sizes. By applying the same analysis to the German transmission grid topology, we show that also in real-world topologies a long-ranged response can be found. PMID:27575148

  1. AcsD catalyzes enantioselective citrate desymmetrization in siderophore biosynthesis.

    PubMed

    Schmelz, Stefan; Kadi, Nadia; McMahon, Stephen A; Song, Lijiang; Oves-Costales, Daniel; Oke, Muse; Liu, Huanting; Johnson, Kenneth A; Carter, Lester G; Botting, Catherine H; White, Malcolm F; Challis, Gregory L; Naismith, James H

    2009-03-01

    Bacterial pathogens need to scavenge iron from their host for growth and proliferation during infection. They have evolved several strategies to do this, one being the biosynthesis and excretion of small, high-affinity iron chelators known as siderophores. The biosynthesis of siderophores is an important area of study, not only for potential therapeutic intervention but also to illuminate new enzyme chemistries. Two general pathways for siderophore biosynthesis exist: the well-characterized nonribosomal peptide synthetase (NRPS)-dependent pathway and the NRPS-independent siderophore (NIS) pathway, which relies on a different family of sparsely investigated synthetases. Here we report structural and biochemical studies of AcsD from Pectobacterium (formerly Erwinia) chrysanthemi, an NIS synthetase involved in achromobactin biosynthesis. The structures of ATP and citrate complexes provide a mechanistic rationale for stereospecific formation of an enzyme-bound (3R)-citryladenylate, which reacts with L-serine to form a likely achromobactin precursor. AcsD is a unique acyladenylate-forming enzyme with a new fold and chemical catalysis strategy. PMID:19182782

  2. Enhanced apparatus for AC Zeeman experiments with ultracold potassium

    NASA Astrophysics Data System (ADS)

    Rotunno, Andrew; Du, Shuangli; Fancher, Charles; Pyle, Andrew; Aubin, Seth

    2016-05-01

    Ultracold atomic potassium is an excellent candidate for studies of the AC Zeeman force, due to small hyperfine splittings. These experiments require a sufficient sample of potassium near an atom chip supporting RF currents, and an RF source which can make rapid phase-continuous frequency sweeps for fast manipulation of spin states. We present progress on the construction of laser amplifier system for improved laser cooling and trapping of potassium, development of a frequency-agile RF source, and research on RF-capable atom chips. The laser amplifier system consists of two tapered amplifiers for producing 0.4 W of 767 nm light, with a goal of collecting 107 potassium atoms at 100 μK, which will then be cooled sympathetically with ultracold rubidium. We have constructed a direct digital synthesizer (DDS) to produce 1-400 MHz with Hz-level linewidth and noise level below -60dBc, and the ability to produce fast 100 μs frequency sweeps. We are investigating atom chip designs for supporting large RF currents. Immediate applications include AC Zeeman potentials and traps for atom interferometry, and quantum many-body physics. Work supported by AFOSR, W&M, and in part by AFRL.

  3. ac impedance measurements of molten salt thermal batteries

    NASA Astrophysics Data System (ADS)

    Singh, Pritpal; Guidotti, Ronald A.; Reisner c, David

    Non-destructive testing of thermal batteries without activating them is a challenging proposition. Molten salt thermal batteries are activated by raising their temperature to above the melting point of the salt constituting the electrolyte. One approach that we have considered is to raise the temperature of the molten salt electrolyte to a temperature below the melting point so that the battery does not get activated yet may provide sufficient mobility of the ionic species to be able to obtain some useful ac impedance measurements. This hypothesis was put to the test for two Li(Si)/FeS 2 molten salt batteries with two electrolytes of different melting points—a standard LiCl-KCl eutectic that melts at 352 °C and a LiBr-KBr-LiCl eutectic with a melting point of 319 °C. ac impedance measurements as a function of frequency and temperature below the melting point are presented for single cells and batteries.

  4. Perfecting the Photometric Calibration of the ACS CCD Cameras

    NASA Astrophysics Data System (ADS)

    Bohlin, Ralph C.

    2016-09-01

    Newly acquired data and improved data reduction algorithms mandate a fresh look at the absolute flux calibration of the charge-coupled device cameras on the Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS). The goals are to achieve a 1% accuracy and to make this calibration more accessible to the HST guest investigator. Absolute fluxes from the CALSPEC1 database for three primary hot 30,000–60,000K WDs define the sensitivity calibrations for the Wide Field Channel (WFC) and High Resolution Channel (HRC) filters. The external uncertainty for the absolute flux is ˜1%, while the internal consistency of the sensitivities in the broadband ACS filters is ˜0.3% among the three primary WD flux standards. For stars as cool as K type, the agreement with the CALSPEC standards is within 1% at the WFC1-1K subarray position, which achieves the 1% precision goal for the first time. After making a small adjustment to the filter bandpass for F814W, the 1% precision goal is achieved over the full F814W WFC field of view for stars of K type and hotter. New encircled energies and absolute sensitivities replace the seminal results of Sirianni et al. that were published in 2005. After implementing the throughput updates, synthetic predictions of the WFC and HRC count rates for the average of the three primary WD standard stars agree with the observations to 0.1%.

  5. Offline detection of broken rotor bars in AC induction motors

    NASA Astrophysics Data System (ADS)

    Powers, Craig Stephen

    ABSTRACT. OFFLINE DETECTION OF BROKEN ROTOR BARS IN AC INDUCTION MOTORS. The detection of the broken rotor bar defect in medium- and large-sized AC induction machines is currently one of the most difficult tasks for the motor condition and monitoring industry. If a broken rotor bar defect goes undetected, it can cause a catastrophic failure of an expensive machine. If a broken rotor bar defect is falsely determined, it wastes time and money to physically tear down and inspect the machine only to find an incorrect diagnosis. Previous work in 2009 at Baker/SKF-USA in collaboration with the Korea University has developed a prototype instrument that has been highly successful in correctly detecting the broken rotor bar defect in ACIMs where other methods have failed. Dr. Sang Bin and his students at the Korea University have been using this prototype instrument to help the industry save money in the successful detection of the BRB defect. A review of the current state of motor conditioning and monitoring technology for detecting the broken rotor bar defect in ACIMs shows improved detection of this fault is still relevant. An analysis of previous work in the creation of this prototype instrument leads into the refactoring of the software and hardware into something more deployable, cost effective and commercially viable.

  6. Testing of a First Order AC Magnetic Susceptometer

    NASA Astrophysics Data System (ADS)

    Fukuda, Ryan; Sunny, Smitha; Ho, Pei-Chun

    2011-11-01

    A first-order AC magnetic susceptometer has been constructed and tested to find the magnetic response of strongly correlated electron materials. The instrument works by using a primary coil to apply a small AC magnetic field of .104 Oe to a sample with a cylindrical coil space of length .635 cm and diameter .355 cm. A lock-in amplifier is used to monitor the induced voltage from a set of secondary coils. By coupling a temperature-controlled system with this instrument, the change in the magnetic signal with respect to temperature is measured. Monitoring the signal changes may indicate the temperature that causes the material to transition to either a ferromagnetic, anti-ferromagnetic, or superconducting state. A 122.47 mg Gd polycrystal was used to test our susceptometer. The data qualitatively agrees with the previous results of magnetization vs. temperature of Gd single crystals by Nigh et al. [1]: there is a steep increase in the pick-up signal at 300 K where Gd becomes ferromagnetic and a peak at 210 K [1]. This susceptometer will be used for our future investigation of magnetic properties of rare earth compounds and nanoparticles in the temperature range of 10 K to 300 K. [4pt] [1] H. E. Nigh, S. Legvold, and F. H. Spedding, Physical Review 132, 1092 (1963)

  7. Long-range response in ac electricity grids

    NASA Astrophysics Data System (ADS)

    Jung, Daniel; Kettemann, Stefan

    2016-07-01

    Local changes in the topology of electricity grids can cause overloads far away from the disturbance [D. Witthaut and M. Timme, Eur. Phys. J. B 86, 377 (2013), 10.1140/epjb/e2013-40469-4], making the prediction of the robustness against changes in the topology—for example, caused by power outages or grid extensions—a challenging task. The impact of single-line additions on the long-range response of dc electricity grids has recently been studied [D. Labavić, R. Suciu, H. Meyer-Ortmanns, and S. Kettemann, Eur. Phys. J.: Spec. Top. 223, 2517 (2014), 10.1140/epjst/e2014-02273-0]. By solving the real part of the static ac load flow equations, we conduct a similar investigation for ac grids. In a regular two-dimensional grid graph with cyclic boundary conditions, we find a power law decay for the change of power flow as a function of distance to the disturbance over a wide range of distances. The power exponent increases and saturates for large system sizes. By applying the same analysis to the German transmission grid topology, we show that also in real-world topologies a long-ranged response can be found.

  8. Long-range response in ac electricity grids.

    PubMed

    Jung, Daniel; Kettemann, Stefan

    2016-07-01

    Local changes in the topology of electricity grids can cause overloads far away from the disturbance [D. Witthaut and M. Timme, Eur. Phys. J. B 86, 377 (2013)EPJBFY1434-602810.1140/epjb/e2013-40469-4], making the prediction of the robustness against changes in the topology-for example, caused by power outages or grid extensions-a challenging task. The impact of single-line additions on the long-range response of dc electricity grids has recently been studied [D. Labavić, R. Suciu, H. Meyer-Ortmanns, and S. Kettemann, Eur. Phys. J.: Spec. Top. 223, 2517 (2014)1951-635510.1140/epjst/e2014-02273-0]. By solving the real part of the static ac load flow equations, we conduct a similar investigation for ac grids. In a regular two-dimensional grid graph with cyclic boundary conditions, we find a power law decay for the change of power flow as a function of distance to the disturbance over a wide range of distances. The power exponent increases and saturates for large system sizes. By applying the same analysis to the German transmission grid topology, we show that also in real-world topologies a long-ranged response can be found.

  9. A driving scheme to reduce AC LED flicker

    NASA Astrophysics Data System (ADS)

    Tan, Jianchuan; Narendran, Nadarajah

    2013-09-01

    Light flicker is a common but unwelcome phenomenon in conventional lighting applications. In solid-state lighting, driving or dimming methods also give rise to light flicker. AC LED products in today's marketplace suffer from flicker, which stems from the arrangement of the micro-LEDs and the driving method. Research has shown that light flicker can be a health hazard to humans. Several solutions have been proposed to reduce light flicker in solid-state lighting applications; however, most have drawbacks in terms of power and other performance. This paper proposes a circuit design to reduce light flicker from AC LEDs while maintaining a normal power factor and high power efficiency. The circuit is composed of one resistive branch and one capacitive branch, and each branch drives a load which is made up of high-voltage LEDs. Percent flicker, power factor, and power efficiency were selected as three metrics, and their benchmarks were set to evaluate the performance of this circuit. Phase shift between the two branches was selected as a factor that could determine the circuit performance. The variations of percent flicker, power factor, and power efficiency as a function of phase shift were identified by theoretical analysis and were verified by experiments. The experimental results show that an optimal solution can be achieved for this circuit design at proper phase shift, where the benchmarks of the three metrics are reached.

  10. Perfecting the Photometric Calibration of the ACS CCD Cameras

    NASA Astrophysics Data System (ADS)

    Bohlin, Ralph C.

    2016-09-01

    Newly acquired data and improved data reduction algorithms mandate a fresh look at the absolute flux calibration of the charge-coupled device cameras on the Hubble Space Telescope (HST) Advanced Camera for Surveys (ACS). The goals are to achieve a 1% accuracy and to make this calibration more accessible to the HST guest investigator. Absolute fluxes from the CALSPEC1 database for three primary hot 30,000-60,000K WDs define the sensitivity calibrations for the Wide Field Channel (WFC) and High Resolution Channel (HRC) filters. The external uncertainty for the absolute flux is ˜1%, while the internal consistency of the sensitivities in the broadband ACS filters is ˜0.3% among the three primary WD flux standards. For stars as cool as K type, the agreement with the CALSPEC standards is within 1% at the WFC1-1K subarray position, which achieves the 1% precision goal for the first time. After making a small adjustment to the filter bandpass for F814W, the 1% precision goal is achieved over the full F814W WFC field of view for stars of K type and hotter. New encircled energies and absolute sensitivities replace the seminal results of Sirianni et al. that were published in 2005. After implementing the throughput updates, synthetic predictions of the WFC and HRC count rates for the average of the three primary WD standard stars agree with the observations to 0.1%.

  11. New Sky Flats for HST's ACS/WFC

    NASA Astrophysics Data System (ADS)

    Lucas, Ray A.; Grogin, Norman A.

    2016-06-01

    We have begun experiments to make new sky flat files for HST's ACS/WFC. Sky flats can be especially useful for deep imaging in such as programs as deep, extragalactic survey programs because they can help to better deal with noise at low levels. Although we also hope to make similar sky flats for some other popular filters including F606W and F814W, we are beginning this experiment with the F435W filter on the ACS/WFC since it is a popular filter in use in many deep extragalactic surveys, and since the bluer filters such as F435W generally have lower throughput and images in that filter are typically noisier than others at some longer mid-optical wavelengths. Initially, although sources will be masked in these images, etc. we are endeavoring to use just post-SM4 F435W images of duration equal to or greater than 800 seconds and which are free of bright stars in order to try and avoid scattered light and sky background color issues as much as possible, although the sky in different images taken at different times and in different directions will likely have some different background levels and color terms in any event. However, our hope is that the final sky flats will be of sufficient S/N to be good calibrators for deep survey programs.

  12. 26 CFR 1.613A-5 - Election under section 613A(c)(4).

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 26 Internal Revenue 7 2011-04-01 2009-04-01 true Election under section 613A(c)(4). 1.613A-5... TAX (CONTINUED) INCOME TAXES (CONTINUED) Natural Resources § 1.613A-5 Election under section 613A(c)(4). The election under section 613A(c)(4) is an annual election which the taxpayer may make by...

  13. 26 CFR 1.613A-5 - Election under section 613A(c)(4).

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Election under section 613A(c)(4). 1.613A-5 Section 1.613A-5 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Natural Resources § 1.613A-5 Election under section 613A(c)(4). The election under section 613A(c)(4) is...

  14. Programmable AC power supply for simulating power transient expected in fusion reactor

    SciTech Connect

    Halimi, B.; Suh, K. Y.

    2012-07-01

    This paper focus on control engineering of the programmable AC power source which has capability to simulate power transient expected in fusion reactor. To generate the programmable power source, AC-AC power electronics converter is adopted to control the power of a set of heaters to represent the transient phenomena of heat exchangers or heat sources of a fusion reactor. The International Thermonuclear Experimental Reactor (ITER) plasma operation scenario is used as the basic reference for producing this transient power source. (authors)

  15. AC conductivity of a niobium thin film in a swept magnetic field.

    PubMed

    Tsindlekht, M I; Genkin, V M; Gazi, S; Chromik, S

    2013-02-27

    We report results of measurements of the ac conductivity of a Nb superconducting thin film in a swept dc magnetic field. In the mixed state the swept dc field creates vortices at the film surface which pass through the film and form the observed ac conductivity. Vortex rate generation does not depend on the value of the dc field and there is a large plateau-like region of dc magnetic fields where the dissipation is approximately constant. A proposed phenomenological model describes quite well the main features of the ac response in these fields, including its dependency on the sweep rate, ac amplitude, frequency, and value of the second and third harmonics.

  16. Distribution of Activator (Ac) Throughout the Maize Genome for Use in Regional Mutagenesis

    PubMed Central

    Kolkman, Judith M.; Conrad, Liza J.; Farmer, Phyllis R.; Hardeman, Kristine; Ahern, Kevin R.; Lewis, Paul E.; Sawers, Ruairidh J. H.; Lebejko, Sara; Chomet, Paul; Brutnell, Thomas P.

    2005-01-01

    A collection of Activator (Ac)-containing, near-isogenic W22 inbred lines has been generated for use in regional mutagenesis experiments. Each line is homozygous for a single, precisely positioned Ac element and the Ds reporter, r1-sc:m3. Through classical and molecular genetic techniques, 158 transposed Ac elements (tr-Acs) were distributed throughout the maize genome and 41 were precisely placed on the linkage map utilizing multiple recombinant inbred populations. Several PCR techniques were utilized to amplify DNA fragments flanking tr-Ac insertions up to 8 kb in length. Sequencing and database searches of flanking DNA revealed that the majority of insertions are in hypomethylated, low- or single-copy sequences, indicating an insertion site preference for genic sequences in the genome. However, a number of Ac transposition events were to highly repetitive sequences in the genome. We present evidence that suggests Ac expression is regulated by genomic context resulting in subtle variations in Ac-mediated excision patterns. These tr-Ac lines can be utilized to isolate genes with unknown function, to conduct fine-scale genetic mapping experiments, and to generate novel allelic diversity in applied breeding programs. PMID:15520264

  17. An H2A Histone Isotype, H2ac, Associates with Telomere and Maintains Telomere Integrity

    PubMed Central

    Tzeng, Tsai-Yu; Lin, I-Hsuan; Hsu, Ming-Ta

    2016-01-01

    Telomeres are capped at the ends of eukaryotic chromosomes and are composed of TTAGGG repeats bound to the shelterin complex. Here we report that a replication-dependent histone H2A isotype, H2ac, was associated with telomeres in human cells and co-immunoprecipitates with telomere repeat factor 2 (TRF2) and protection of telomeres protein 1 (POT1), whereas other histone H2A isotypes and mutations of H2ac did not bind to telomeres or these two proteins. The amino terminal basic domain of TRF2 was necessary for the association with H2ac and for the recruitment of H2ac to telomeres. Depletion of H2ac led to loss of telomeric repeat sequences, the appearance of dysfunctional telomeres, and chromosomal instability, including chromosomal breaks and anaphase bridges, as well as accumulation of telomere-associated DNA damage factors in H2ac depleted cells. Additionally, knockdown of H2ac elicits an ATM-dependent DNA damage response at telomeres and depletion of XPF protects telomeres against H2ac-deficiency-induced G-strand overhangs loss and DNA damage response, and prevents chromosomal instability. These findings suggest that the H2A isotype, H2ac, plays an essential role in maintaining telomere functional integrity. PMID:27228173

  18. RG flow of AC conductivity in soft wall model of QCD

    NASA Astrophysics Data System (ADS)

    Bhatnagar, Neha; Siwach, Sanjay

    2016-03-01

    We study the Renormalization Group (RG) flow of AC conductivity in soft wall model of holographic QCD. We consider the charged black hole metric and the explicit form of AC conductivity is obtained at the cutoff surface. We plot the numerical solution of conductivity flow as a function of radial coordinate. The equation of gauge field is also considered and the numerical solution is obtained for AC conductivity as a function of frequency. The results for AC conductivity are also obtained for different values of chemical potential and Gauss-Bonnet couplings.

  19. Orthogonal-core type three-phase dc-ac converter

    SciTech Connect

    Ichinokura, O.; Saito, H.; Jinzenji, T. ); Tajima, K. )

    1993-03-01

    In a previous paper, the authors proposed an orthogonal-core type dc-ac converter for use in photovoltaic power systems. The dc-ac converter has such desirable features as a simple construction, high degree of safety, and ease of maintenance. The operating characteristics of a single-phase converter for residential photovoltaic power systems have also been reported. In this paper, the authors discuss the basic operation of an orthogonal-core type dc-ac converter for a three-phase power system based on simulations and experiments. An optimal construction of the orthogonal-core type three-phase dc-ac converter has been developed.

  20. ac18 is not essential for the propagation of Autographa californica multiple nucleopolyhedrovirus

    SciTech Connect

    Wang Yanjie; Wu Wenbi; Li Zhaofei; Yuan Meijin; Feng Guozhong; Yu Qian; Yang Kai Pang Yi

    2007-10-10

    orf18 (ac18) of Autographa californica multiple nucleopolyhedrovirus (AcMNPV) is a highly conserved gene in lepidopteran nucleopolyhedroviruses, but its function remains unknown. In this study, an ac18 knockout AcMNPV bacmid was generated to determine the role of ac18 in baculovirus life cycle. After transfection of Sf-9 cells, the ac18-null mutant showed similar infection pattern to the parent virus and the ac18 repair virus with respect to the production of infectious budded virus, occlusion bodies, or the formation of nucleocapsids as visualized by electron microscopy. The deletion mutant did not reduce AcMNPV infectivity for Trichoplusia ni in LD{sub 50} bioassay; however, it did take 24 h longer for deleted mutant to kill T. ni larvae than wild-type virus in LT{sub 50} bioassay. Our results demonstrate that ac18 is not essential for viral propagation both in vitro and in vivo, but it may play a role in efficient virus infection in T. ni larvae.

  1. Autographa californica multiple nucleopolyhedrovirus ac142, a core gene that is essential for BV production and ODV envelopment

    SciTech Connect

    McCarthy, Christina B.; Da, Xiaojiang; Donly, Cam; Theilmann, David A.

    2008-03-15

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac142 is a baculovirus core gene and encodes a protein previously shown to associate with occlusion-derived virus (ODV). To determine its role in the baculovirus life cycle, we used the AcMNPV bacmid system to generate an ac142 deletion virus (AcBAC{sup ac142KO-PH-GFP}). Fluorescence and light microscopy revealed that AcBAC{sup ac142KO-PH-GFP} exhibits a single-cell infection phenotype. Titration assays and Western blot confirmed that AcBAC{sup ac142KO-PH-GFP} is unable to produce budded virus (BV). However, viral DNA replication is unaffected and the development of occlusion bodies in AcBAC{sup ac142KO-PH-GFP}-transfected cells evidenced progression to very late phases of the viral infection. Western blot analysis showed that AC142 is expressed in the cytoplasm and nucleus throughout infection and that it is a structural component of BV and ODV which localizes to nucleocapsids. Electron microscopy indicates that ac142 is required for nucleocapsid envelopment to form ODV and their subsequent occlusion, a fundamental process to all baculoviruses.

  2. Autographa californica multiple nucleopolyhedrovirus ac142, a core gene that is essential for BV production and ODV envelopment.

    PubMed

    McCarthy, Christina B; Dai, Xiaojiang; Donly, Cam; Theilmann, David A

    2008-03-15

    Autographa californica multiple nucleopolyhedrovirus (AcMNPV) ac142 is a baculovirus core gene and encodes a protein previously shown to associate with occlusion-derived virus (ODV). To determine its role in the baculovirus life cycle, we used the AcMNPV bacmid system to generate an ac142 deletion virus (AcBAC(ac142KO-PH-GFP)). Fluorescence and light microscopy revealed that AcBAC(ac142KO-PH-GFP) exhibits a single-cell infection phenotype. Titration assays and Western blot confirmed that AcBAC(ac142KO-PH-GFP) is unable to produce budded virus (BV). However, viral DNA replication is unaffected and the development of occlusion bodies in AcBAC(ac142KO-PH-GFP)-transfected cells evidenced progression to very late phases of the viral infection. Western blot analysis showed that AC142 is expressed in the cytoplasm and nucleus throughout infection and that it is a structural component of BV and ODV which localizes to nucleocapsids. Electron microscopy indicates that ac142 is required for nucleocapsid envelopment to form ODV and their subsequent occlusion, a fundamental process to all baculoviruses.

  3. Lack of mucin MUC5AC field change expression associated with tubulovillous and villous colorectal adenomas

    PubMed Central

    Longman, R; Douthwaite, J; Sylvester, P; O'Leary, D; Warren, B; Corfield, A; Thomas, M

    2000-01-01

    Background—MUC5AC is a secreted mucin aberrantly expressed by polypoid colorectal adenomas. It has been hypothesised that the "normal" surrounding colorectal mucosa expresses MUC5AC as a field change phenomenon that can be used to predict adenoma recurrence following resection. Aim—To determine if there is a field change of de novo MUC5AC expression in histologically normal rectal mucosa adjacent to villous and tubulovillous adenomas, and thus whether MUC5AC expression can be used as a marker of early tumour recurrence. Methods—In a prospective cohort study paired mucosal biopsies of adenomatous and macroscopically "normal" mucosa were obtained from 11 patients with villous and 11 patients with tubulovillous adenomas who underwent primary resection for purpose of cure. The tissues were studied to determine MUC5AC gene expression by immunohistochemistry and in situ hybridisation. Patients were followed up by flexible sigmoidoscopy to detect the presence of early local recurrence. Results—10 villous adenomas showed mature MUC5AC glycoprotein and all 11 expressed MUC5AC mRNA. Five tubulovillous adenomas showed mature MUC5AC glycoprotein and 10 expressed MUC5AC mRNA. Neoexpression of the MUC5AC mucin gene was not detected in any of the mucosal biopsies taken adjacent to either villous or tubulovillous adenomas, even in three patients with early, locally recurrent disease. Conclusions—Aberrant MUC5AC gene expression is not a "field change" in the colorectal mucosa in patients with rectal adenomas and therefore cannot be used to predict local recurrence of villous and tubulovillous adenomas. Key Words: mucin • colorectal adenoma • gene expression • field change PMID:10767823

  4. Age-related changes in lamin A/C expression in cardiomyocytes.

    PubMed

    Afilalo, Jonathan; Sebag, Igal A; Chalifour, Lorraine E; Rivas, Daniel; Akter, Rahima; Sharma, Kamal; Duque, Gustavo

    2007-09-01

    Lamin A and C (A/C) are type V intermediate filaments that form the nuclear lamina. Lamin A/C mutations lead to reduced expression of lamin A/C and diverse phenotypes such as familial cardiomyopathies and accelerated aging syndromes. Normal aging is associated with reduced expression of lamin A/C in osteoblasts and dermal fibroblasts but has never been assessed in cardiomyocytes. Our objective was to compare the expression of lamin A/C in cardiomyocytes of old (24 mo) versus young (4 mo) C57Bl/6J mice using a well-validated mouse model of aging. Lamin B1 was used as a control. Immunohistochemical and immunofluorescence analyses showed reduced expression of lamin A/C in cardiomyocyte nuclei of old mice (proportion of nuclei expressing lamin A/C, 9% vs. 62%, P < 0.001). Lamin A/C distribution was scattered peripherally and perinuclear in old mice, whereas it was homogeneous throughout the nuclei in young mice. Western blot analyses confirmed reduced expression of lamin A/C in nuclear extracts of old mice (ratio of lamin A/C to B1, 0.6 vs. 1.2, P < 0.01). Echocardiographic studies showed increased left ventricular wall thickness with preserved cavity size (concentric remodeling), increased left ventricular mass, and a slight reduction in fractional shortening in old mice. This is the first study to show that normal aging is associated with reduced expression and altered distribution of lamin A/C in nuclei of cardiomyocytes.

  5. Numerical and theoretical evaluations of AC losses for single and infinite numbers of superconductor strips with direct and alternating transport currents in external AC magnetic field

    NASA Astrophysics Data System (ADS)

    Kajikawa, K.; Funaki, K.; Shikimachi, K.; Hirano, N.; Nagaya, S.

    2010-11-01

    AC losses in a superconductor strip are numerically evaluated by means of a finite element method formulated with a current vector potential. The expressions of AC losses in an infinite slab that corresponds to a simple model of infinitely stacked strips are also derived theoretically. It is assumed that the voltage-current characteristics of the superconductors are represented by Bean’s critical state model. The typical operation pattern of a Superconducting Magnetic Energy Storage (SMES) coil with direct and alternating transport currents in an external AC magnetic field is taken into account as the electromagnetic environment for both the single strip and the infinite slab. By using the obtained results of AC losses, the influences of the transport currents on the total losses are discussed quantitatively.

  6. Resistojet control and power for high frequency ac buses

    NASA Technical Reports Server (NTRS)

    Gruber, Robert P.

    1987-01-01

    Resistojets are operational on many geosynchronous communication satellites which all use dc power buses. Multipropellant resistojets were selected for the Initial Operating Capability (IOC) Space Station which will supply 208 V, 20 kHz power. This paper discusses resistojet heater temperature controllers and passive power regulation methods for ac power systems. A simple passive power regulation method suitable for use with regulated sinusoidal or square wave power was designed and tested using the Space Station multipropellant resistojet. The breadboard delivered 20 kHz power to the resistojet heater. Cold start surge current limiting, a power efficiency of 95 percent, and power regulation of better than 2 percent were demonstrated with a two component, 500 W breadboard power controller having a mass of 0.6 kg.

  7. Input-current shaped ac to dc converters

    NASA Technical Reports Server (NTRS)

    1986-01-01

    The problem of achieving near unity power factor while supplying power to a dc load from a single phase ac source of power is examined. Power processors for this application must perform three functions: input current shaping, energy storage, and output voltage regulation. The methods available for performing each of these three functions are reviewed. Input current shaping methods are either active or passive, with the active methods divided into buck-like and boost-like techniques. In addition to large reactances, energy storage methods include resonant filters, active filters, and active storage schemes. Fast voltage regulation can be achieved by post regulation or by supplementing the current shaping topology with an extra switch. Some indications of which methods are best suited for particular applications concludes the discussion.

  8. Longipetalosides A-C, new steroidal saponins from Tribulus longipetalus.

    PubMed

    Naveed, Muhammad Akram; Riaz, Naheed; Saleem, Muhammad; Jabeen, Bushra; Ashraf, Muhammad; Ismail, Tayaba; Jabbar, Abdul

    2014-05-01

    Longipetalosides A-C (1-3); three new furostane steroidal saponins together with (25S)-5α-furastan-3β,22,26-triol (4) and gitogenin (5) were isolated from the methanolic extract of the whole plant of Tribulus longipetalus. The structures of these compounds (1-5) were established by using 1D ((1)H, (13)C) and 2D NMR (HMQC, HMBC, COSY, NOESY) spectroscopy, and mass spectrometry (ESIMS, HRESIMS), and in comparison with literature data reported for related compounds. Compounds 1-5 were evaluated for their inhibitory activities against enzymes α-glucosidase, lipoxygenase, acetylcholinesterase, and butyrylcholinesterase. Only the compounds 4 and 5 were found as the inhibitors of enzyme α-glucosidase with IC50 values of 33.5±0.22 and 37.2±0.18μM, respectively.

  9. AC magnetic field losses in BSCCO-2223 superconducting tapes

    SciTech Connect

    Lelovic, M.; Mench, S.; Deis, T.

    1997-09-01

    The AC magnetic losses at power frequencies (60 Hz) were investigated for mono- and multifilament Ag-sheathed (Bi, Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub y} (BSCCO-2223) tapes with similar transport critical current (I{sub c}) values at 77 K. The multifilament sample exhibited higher losses than the monofilament under the same conditions. Loss peaks are discussed in terms of intergranular, intragranular and eddy current losses. Because of BSCCO`s anisotropy, field orientation has a large effect on the magnitude of these peaks, even at relatively small angles. Losses for fields applied parallel to the c-axis of the textured BSCCO grains are larger by more than one order of magnitude than those applied perpendicular.

  10. AC impedance study of degradation of porous nickel battery electrodes

    NASA Technical Reports Server (NTRS)

    Lenhart, Stephen J.; Macdonald, D. D.; Pound, B. G.

    1987-01-01

    AC impedance spectra of porous nickel battery electrodes were recorded periodically during charge/discharge cycling in concentrated KOH solution at various temperatures. A transmission line model (TLM) was adopted to represent the impedance of the porous electrodes, and various model parameters were adjusted in a curve fitting routine to reproduce the experimental impedances. Degradation processes were deduced from changes in model parameters with electrode cycling time. In developing the TLM, impedance spectra of planar (nonporous) electrodes were used to represent the pore wall and backing plate interfacial impedances. These data were measured over a range of potentials and temperatures, and an equivalent circuit model was adopted to represent the planar electrode data. Cyclic voltammetry was used to study the characteristics of the oxygen evolution reaction on planar nickel electrodes during charging, since oxygen evolution can affect battery electrode charging efficiency and ultimately electrode cycle life if the overpotential for oxygen evolution is sufficiently low.

  11. Effect of low voltage AC fields on cardiovascular implants.

    PubMed

    Kothandaraman, Anjana; Anson, Tony; Reynolds, Alan

    2015-01-01

    Coronary Artery Stents have been the preferred form of treatment for vascular occlusive disease, due to the minimally invasive surgical procedure, post-operative recovery time and cost, when compared to open coronary bypass surgery. The cellular response upon applying an AC electric field to type 316LM Stainless Steel stent mimics was investigated in this paper. The highest RBC adhesion was observed at voltages higher than 88 mV and lower than 74 mV. Their unique alignment along the lines of fracture on the stent surface at 88 mV was a phenomenon caused by an increase in electrical conductivity in these regions. Being able to control RBC adhesion may have various clinical implications such as inhibition of thrombus formation, and provide a basis to analyse whether electric fields may be applied to cancer therapy as well.

  12. An AC drive system for a battery driven moped

    SciTech Connect

    Nandi, S.; Saha, S.; Sharon, M.; Sundersingh, V.P.

    1995-12-31

    A petrol driven moped is converted to an electric one by replacing the petrol engine by a three phase 1.5 HR, AC squirrel cage induction motor drive system. The motor voltage rating selected is 200 V to keep the DC boost voltage level to a reasonable value.f the power source used is a high energy density, 24 V, 110 Ah, Ni-Zn battery. A modified indirect current controlled step-up chopper as well as a standard push-pull DC-DC boost converter is studied for the boost scheme. A simple three phase quasi-square wave inverter is designed along with suitable protection for driving the motor. Successful trial test of the system has been conducted at the laboratory.

  13. AC biosusceptometry in the study of drug delivery.

    PubMed

    Corá, L A; Romeiro, F G; Stelzer, M; Américo, M F; Oliveira, R B; Baffa, O; Miranda, J R A

    2005-06-15

    Conventionally, pharmaceutical substances are administered orally because the gastrointestinal tract possesses the appropriate features for drug absorption. Nevertheless, the gastrointestinal tract physiology is complex and influenced by many factors. These factors must be completely understood for the optimization of oral drug delivery systems. Although in vitro tests provide information about release and drug absorption profiles, in vivo studies are essential, due to the biological variability. Several techniques have been employed in an attempt to conveniently characterize the behavior of solid dosage forms in vivo. The noninvasive biomagnetic technique of alternate current biosusceptometry (ACB) has been used in studies focusing on gastrointestinal motility and, more recently, to evaluate the performance of magnetic dosage forms. This article will discuss the main characteristics of AC biosusceptometry and its applicability for determination of the relationship between the human gastrointestinal tract and orally administered pharmaceutical dosage forms.

  14. Relativistic AC gyromagnetic effects in ultraintense laser-matter interaction.

    PubMed

    Geindre, J P; Audebert, P; Marjoribanks, R S

    2006-08-25

    We demonstrate that in ultraintense ultrafast laser-matter interaction, the interplay of laser-induced oscillating space-charge fields with laser E and B fields can strongly affect whether the interaction is relativistic or not: stronger laser fields may not in fact produce more relativistic plasma interactions. We show that there exists a regime of interaction, in the relation of laser intensity and incident angle, for which the Brunel effect of electron acceleration is strongly suppressed by AC gyromagnetic fields, at a frequency different from the laser field. Analytically and with 1.5D particle-in-cell modeling, we show that from gyromagnetic effects, even in the absence of usual J x B second-harmonic contributions, there are strong effects on the harmonic emission and on the generation of attosecond pulses. PMID:17026310

  15. ACS/SBC Internal Lamp P-flat Monitoring

    NASA Astrophysics Data System (ADS)

    Avila, Roberto J.; Chiaberge, Marco; Bohlin, Ralph

    2016-06-01

    We report on a Cycle 23 calibration program to monitor the status of the SBC P-flat. We find random pixel to pixel changes to be small, with only ˜2% of pixels having changed by more than 3σ. There are coherent changes that we measure to be above the poisson errors, in some regions as high as 4% peak to peak. We therefore recommend that the ACS team obtain new observations in order to create a new P-flat. We also measured the degradation of the deuterium lamp used to create internal flats. The brightness of the lamp is currently ˜65% of its initial level, the degradation being dependent on lifetime usage.

  16. Surgical treatment of teenagers with high AC/A ratios.

    PubMed

    Kushner, Burton J

    2014-01-01

    The surgical approach to esotropia with a high AC/A ratio in teenagers should be dichotomized based on whether or not there is satisfactory alignment at distance with the cycloplegic correction in place. If there is not, surgery should target the near angle with glasses on. If there is good alignment at distance, bifocals should be used, and surgery deferred until the patient is approximately 18 years of age. At that time, surgery could be entertained to eliminate the need of a bifocal, by targeting the near angle measured through the distance correction. Surgery for the purpose of eliminating a bifocal in younger teenagers may be unnecessary as 99% of those who maintained satisfactory distance alignment outgrew the need of a bifocal by 18 years of age. However, many still needed a bifocal in their early teenage years.

  17. Development of AC and DC Power Supply Direct Interface Converter

    NASA Astrophysics Data System (ADS)

    Kato, Koji; Itoh, Jun-Ichi

    This paper proposes a novel control method for a direct interface converter for management of the energy flow in either an AC or DC supply. The proposed converter is constructed based on an indirect matrix converter. Therefore a proposed control strategy is based on an indirect control method with a triangular carrier wave. The basic operation of the proposed control method is confirmed by experimental results. In addition, this paper also proposes a commutation error compensation method of an output voltage error and an input current error for an indirect matrix converter. In the proposed method, the output voltage and input current error by the commutation can be compensated at the same time, because the PWM pulse of each switch is directly compensated. The validity of the proposed method is confirmed by experimental results. Those results prove that the proposed compensation method can decrease total harmonic distortion (THD) of the input and output current.

  18. A flux-coupled ac/dc magnetizing device.

    PubMed

    Gopman, D B; Liu, H; Kent, A D

    2013-06-01

    We report on an instrument for applying ac and dc magnetic fields by capturing the flux from a rotating permanent magnet and projecting it between two adjustable pole pieces. This can be an alternative to standard electromagnets for experiments with small samples or in probe stations in which an applied magnetic field is needed locally, with advantages that include a compact form-factor, very low power requirements and dissipation as well as fast field sweep rates. This flux capture instrument (FLUXCAP) can produce fields from -400 to +400 mT, with field resolution less than 1 mT. It generates static magnetic fields as well as ramped fields, with ramping rates as high as 10 T/s. We demonstrate the use of this apparatus for studying the magnetotransport properties of spin-valve nanopillars, a nanoscale device that exhibits giant magnetoresistance. PMID:23822372

  19. Spectroscopic AC Susceptibility Imaging (sASI) of Magnetic Nanoparticles

    PubMed Central

    Ficko, Bradley W.; Nadar, Priyanka M.; Diamond, Solomon G.

    2014-01-01

    This study demonstrates a method for alternating current (AC) susceptibility imaging (ASI) of magnetic nanoparticles (mNPs) using low cost instrumentation. The ASI method uses AC magnetic susceptibility measurement to create tomographic images using an array of drive coils, compensation coils and fluxgate magnetometers. Using a spectroscopic approach in conjunction with ASI, a series of tomographic images can be created for each frequency measurement and is termed sASI. The advantage of sASI is that mNPs can be simultaneously characterized and imaged in a biological medium. System calibration was performed by fitting the in-phase and out-of-phase susceptibility measurements of an mNP sample with a hydrodynamic diameter of 100 nm to a Brownian relaxation model (R2 = 0.96). Samples of mNPs with core diameters of 10 and 40 nm and a sample of 100 nm hydrodynamic diameter were prepared in 0.5 ml tubes. Three mNP samples were arranged in a randomized array and then scanned using sASI with six frequencies between 425 and 925 Hz. The sASI scans showed the location and quantity of the mNP samples (R2 = 0.97). Biological compatibility of the sASI method was demonstrated by scanning mNPs that were injected into a pork sausage. The mNP response in the biological medium was found to correlate with a calibration sample (R2 = 0.97, p <0.001). These results demonstrate the concept of ASI and advantages of sASI. PMID:25477704

  20. Spectroscopic AC Susceptibility Imaging (sASI) of Magnetic Nanoparticles.

    PubMed

    Ficko, Bradley W; Nadar, Priyanka M; Diamond, Solomon G

    2015-02-01

    This study demonstrates a method for alternating current (AC) susceptibility imaging (ASI) of magnetic nanoparticles (mNPs) using low cost instrumentation. The ASI method uses AC magnetic susceptibility measurement to create tomographic images using an array of drive coils, compensation coils and fluxgate magnetometers. Using a spectroscopic approach in conjunction with ASI, a series of tomographic images can be created for each frequency measurement and is termed sASI. The advantage of sASI is that mNPs can be simultaneously characterized and imaged in a biological medium. System calibration was performed by fitting the in-phase and out-of-phase susceptibility measurements of an mNP sample with a hydrodynamic diameter of 100 nm to a Brownian relaxation model (R(2) = 0.96). Samples of mNPs with core diameters of 10 and 40 nm and a sample of 100 nm hydrodynamic diameter were prepared in 0.5 ml tubes. Three mNP samples were arranged in a randomized array and then scanned using sASI with six frequencies between 425 and 925 Hz. The sASI scans showed the location and quantity of the mNP samples (R(2) = 0.97). Biological compatibility of the sASI method was demonstrated by scanning mNPs that were injected into a pork sausage. The mNP response in the biological medium was found to correlate with a calibration sample (R(2) = 0.97, p <0.001). These results demonstrate the concept of ASI and advantages of sASI. PMID:25477704