Science.gov

Sample records for ac source distribution

  1. Simultaneous distribution of AC and DC power

    DOEpatents

    Polese, Luigi Gentile

    2015-09-15

    A system and method for the transport and distribution of both AC (alternating current) power and DC (direct current) power over wiring infrastructure normally used for distributing AC power only, for example, residential and/or commercial buildings' electrical wires is disclosed and taught. The system and method permits the combining of AC and DC power sources and the simultaneous distribution of the resulting power over the same wiring. At the utilization site a complementary device permits the separation of the DC power from the AC power and their reconstruction, for use in conventional AC-only and DC-only devices.

  2. High-Frequency ac Power-Distribution System

    NASA Technical Reports Server (NTRS)

    Hansen, Irving G.; Mildice, James

    1987-01-01

    Loads managed automatically under cycle-by-cycle control. 440-V rms, 20-kHz ac power system developed. System flexible, versatile, and "transparent" to user equipment, while maintaining high efficiency and low weight. Electrical source, from dc to 2,200-Hz ac converted to 440-V rms, 20-kHz, single-phase ac. Power distributed through low-inductance cables. Output power either dc or variable ac. Energy transferred per cycle reduced by factor of 50. Number of parts reduced by factor of about 5 and power loss reduced by two-thirds. Factors result in increased reliability and reduced costs. Used in any power-distribution system requiring high efficiency, high reliability, low weight, and flexibility to handle variety of sources and loads.

  3. High-frequency ac power distribution in Space Station

    NASA Technical Reports Server (NTRS)

    Tsai, Fu-Sheng; Lee, Fred C. Y.

    1990-01-01

    A utility-type 20-kHz ac power distribution system for the Space Station, employing resonant power-conversion techniques, is presented. The system converts raw dc voltage from photovoltaic cells or three-phase LF ac voltage from a solar dynamic generator into a regulated 20-kHz ac voltage for distribution among various loads. The results of EASY5 computer simulations of the local and global performance show that the system has fast response and good transient behavior. The ac bus voltage is effectively regulated using the phase-control scheme, which is demonstrated with both line and load variations. The feasibility of paralleling the driver-module outputs is illustrated with the driver modules synchronized and sharing a common feedback loop. An HF sinusoidal ac voltage is generated in the three-phase ac input case, when the driver modules are phased 120 deg away from one another and their outputs are connected in series.

  4. Distributed cooperative control of AC microgrids

    NASA Astrophysics Data System (ADS)

    Bidram, Ali

    In this dissertation, the comprehensive secondary control of electric power microgrids is of concern. Microgrid technical challenges are mainly realized through the hierarchical control structure, including primary, secondary, and tertiary control levels. Primary control level is locally implemented at each distributed generator (DG), while the secondary and tertiary control levels are conventionally implemented through a centralized control structure. The centralized structure requires a central controller which increases the reliability concerns by posing the single point of failure. In this dissertation, the distributed control structure using the distributed cooperative control of multi-agent systems is exploited to increase the secondary control reliability. The secondary control objectives are microgrid voltage and frequency, and distributed generators (DGs) active and reactive powers. Fully distributed control protocols are implemented through distributed communication networks. In the distributed control structure, each DG only requires its own information and the information of its neighbors on the communication network. The distributed structure obviates the requirements for a central controller and complex communication network which, in turn, improves the system reliability. Since the DG dynamics are nonlinear and non-identical, input-output feedback linearization is used to transform the nonlinear dynamics of DGs to linear dynamics. Proposed control frameworks cover the control of microgrids containing inverter-based DGs. Typical microgrid test systems are used to verify the effectiveness of the proposed control protocols.

  5. UPS with input commutation between ac and dc sources of power

    SciTech Connect

    Severinsky, A.J.

    1993-08-31

    An uninterruptible power supply is described, said power supply comprising: AC input terminal means for receiving a first AC voltage from an AC power source; DC input terminal means for receiving a first DC voltage from a DC power source; AC output terminal means for connecting to a load; converter means for converting said first AC voltage to a second DC voltage across electrical charge storage means coupled to said converter means, said second DC voltage being larger than the maximum peak voltage of said first AC voltage and said first DC voltage; switching means coupled to said AC power source and said DC power source for selectively connecting said AC power source or said DC power source to said converter means; inverter means coupled to said electrical charge storage means for receiving said second DC voltage and inverting said second DC voltage to a second AC voltage, said second AC voltage being coupled to said AC output terminal means; and control means coupled to said switching means for controlling the operation of said switching means, said control means operating said switching means to connect said AC power source to said converter means only when said first AC voltage is within a predetermined range and operating to connect said DC power source to said converter means when said first AC voltage is outside of said range.

  6. Measurements of AC Losses and Current Distribution in Superconducting Cables

    SciTech Connect

    Nguyen, Doan A; Ashworth, Stephen P; Duckworth, Robert C; Carter, Bill; Fleshler, Steven

    2011-01-01

    This paper presents our new experimental facility and techniques to measure ac loss and current distribution between the layers for High Temperature Superconducting (HTS) cables. The facility is powered with a 45 kVA three-phase power supply which can provide three-phase currents up to 5 kA per phase via high current transformers. The system is suitable for measurements at any frequency between 20 and 500 Hz to better understand the ac loss mechanisms in HTS cables. In this paper, we will report techniques and results for ac loss measurements carried out on several HTS cables with and without an HTS shielding layer. For cables without a shielding layer, care must be taken to control the effect of the magnetic fields from return currents on loss measurements. The waveform of the axial magnetic field was also measured by a small pick-up coil placed inside a two-layer cable. The temporal current distribution between the layers can be calculated from the waveform of the axial field.

  7. Using ac dipoles to localize sources of beam coupling impedance

    NASA Astrophysics Data System (ADS)

    Biancacci, N.; Tomás, R.

    2016-05-01

    The beam coupling impedance is one of the main sources of beam instabilities and emittance blow up in circular accelerators. A refined machine impedance evaluation is therefore required in order to understand and model intensity dependent effects and instabilities that may limit the machine performance. For this reason, many impedance source localization techniques have been developed. In this work we present the impedance localization technique based on the observation of phase advance versus intensity at the beam position monitors using ac dipoles to force betatron oscillations. We present analytical formulas for the interpretation of measurements together with simulations to benchmark and illustrate the equations. Studies on the method accuracy for different Fourier transform algorithms are presented as well as first exploratory measurements performed in the LHC.

  8. Combined Operation of AC and DC Distribution System with Distributed Generation Units

    NASA Astrophysics Data System (ADS)

    Noroozian, Reza; Abedi, Mehrdad; Gharehpetian, Gevorg

    2010-07-01

    This paper presents a DC distribution system which has been supplied by external AC systems as well as local DG units in order to demonstrate an overall solution to power quality issue. In this paper, the proposed operation method is demonstrated by simulation of power transfer between external AC systems, DG units, AC and DC loads. The power flow control in DC distribution system has been achieved by network converters and DG converters. Also, the mathematical model of the network, DG and load converters are obtained by using the average technique, which allows converter systems accurately simulated and control strategies for this converters is achieved. A suitable control strategy for network converters has been proposed that involves DC voltage droop regulator and novel instantaneous power regulation scheme. Also, a novel control technique has been proposed for DG converters. In this paper, a novel control system based on stationary and synchronously rotating reference frame has been proposed for load converters for supplying AC loads connected to the DC bus by balanced voltages. The several case studies have been studied based on proposed methods. The simulation results show that DC distribution systems including DG units can improve the power quality at the point of common coupling (PCC) in the power distribution system or industrial power system.

  9. Development of the Adaptive Collision Source (ACS) method for discrete ordinates

    SciTech Connect

    Walters, W.; Haghighat, A.

    2013-07-01

    We have developed a new collision source method to solve the Linear Boltzmann Equation (LBE) more efficiently by adaptation of the angular quadrature order. The angular adaptation method is unique in that the flux from each scattering source iteration is obtained, with potentially a different quadrature order. Traditionally, the flux from every iteration is combined, with the same quadrature applied to the combined flux. Since the scattering process tends to distribute the radiation more evenly over angles (i.e., make it more isotropic), the quadrature requirements generally decrease with each iteration. This allows for an optimal use of processing power, by using a high order quadrature for the first few iterations that need it, before shifting to lower order quadratures for the remaining iterations. This is essentially an extension of the first collision source method, and we call it the adaptive collision source method (ACS). The ACS methodology has been implemented in the TITAN discrete ordinates code, and has shown a relative speedup of 1.5-2.5 on a test problem, for the same desired level of accuracy. (authors)

  10. A Numerical Simulation Of The Pulse Sequence Reconstruction in AC Biased TESs With a {beta} Source

    SciTech Connect

    Ferrari, Lorenza; Vaccarone, Renzo

    2009-12-16

    We study the response of micro-calorimeters based on Ir/Au TESs biased by an AC voltage in the MHz range to the power input generated by beta emission in a Re source thermally connected to the calorimeter itself. The micro-calorimeter is assumed to work at -80 mK, and the energy pulses corresponding to the beta emission have an energy distributed between zero and 2.58 KeV. In this numerical simulation the TES is inserted in a RLC resonating circuit, with a low quality factor. The thermal conductivities between the source and the calorimeter and that from the calorimeter to the heat sink are non-linear. The superconducting to normal transition of the TES is described by a realistic non-linear model. The AC current at the carrier frequency, modulated by the changing resistance of the TES, is demodulated and the output is filtered. The resulting signal is analyzed to deduce the attainable time resolution and the linearity of the response.

  11. A single-phase embedded Z-source DC-AC inverter.

    PubMed

    Kim, Se-Jin; Lim, Young-Cheol

    2014-01-01

    In the conventional DC-AC inverter consisting of two DC-DC converters with unipolar output capacitors, the output capacitor voltages of the DC-DC converters must be higher than the DC input voltage. To overcome this weakness, this paper proposes a single-phase DC-AC inverter consisting of two embedded Z-source converters with bipolar output capacitors. The proposed inverter is composed of two embedded Z-source converters with a common DC source and output AC load. Though the output capacitor voltages of the converters are relatively low compared to those of a conventional inverter, an equivalent level of AC output voltages can be obtained. Moreover, by controlling the output capacitor voltages asymmetrically, the AC output voltage of the proposed inverter can be higher than the DC input voltage. To verify the validity of the proposed inverter, experiments were performed with a DC source voltage of 38 V. By controlling the output capacitor voltages of the converters symmetrically or asymmetrically, the proposed inverter can produce sinusoidal AC output voltages. The experiments show that efficiencies of up to 95% and 97% can be achieved with the proposed inverter using symmetric and asymmetric control, respectively. PMID:25133241

  12. A Single-Phase Embedded Z-Source DC-AC Inverter

    PubMed Central

    Kim, Se-Jin; Lim, Young-Cheol

    2014-01-01

    In the conventional DC-AC inverter consisting of two DC-DC converters with unipolar output capacitors, the output capacitor voltages of the DC-DC converters must be higher than the DC input voltage. To overcome this weakness, this paper proposes a single-phase DC-AC inverter consisting of two embedded Z-source converters with bipolar output capacitors. The proposed inverter is composed of two embedded Z-source converters with a common DC source and output AC load. Though the output capacitor voltages of the converters are relatively low compared to those of a conventional inverter, an equivalent level of AC output voltages can be obtained. Moreover, by controlling the output capacitor voltages asymmetrically, the AC output voltage of the proposed inverter can be higher than the DC input voltage. To verify the validity of the proposed inverter, experiments were performed with a DC source voltage of 38 V. By controlling the output capacitor voltages of the converters symmetrically or asymmetrically, the proposed inverter can produce sinusoidal AC output voltages. The experiments show that efficiencies of up to 95% and 97% can be achieved with the proposed inverter using symmetric and asymmetric control, respectively. PMID:25133241

  13. Dose distributions in regions containing beta sources: Irregularly shaped source distributions in homogeneous media

    SciTech Connect

    Werner, B.L. )

    1991-11-01

    Methods are introduced by which dose rate distributions due to nonuniform, irregularly shaped distributions of beta emitters can be calculated using dose rate distributions for uniform, spherical source distributions. The dose rate distributions can be written in the MIRD formalism.

  14. Negative hydrogen ion beam extraction from an AC heated cathode driven Bernas-type ion source

    NASA Astrophysics Data System (ADS)

    Okano, Y.; Miyamoto, N.; Kasuya, T.; Wada, M.

    2015-04-01

    A plasma grid structure was installed to a Bernas-type ion source used for ion implantation equipment. A negative hydrogen (H-) ion beam was extracted by an AC driven ion source by adjusting the bias to the plasma grid. The extracted electron current was reduced by positively biasing the plasma grid, while an optimum plasma grid bias voltage for negative ion beam extraction was found to be positive 3 V with respect to the arc chamber. Source operations with AC cathode heating show extraction characteristics almost identical to that with DC cathode heating, except a minute increase in H- current at higher frequency of cathode heating current.

  15. Method And Apparatus For Production Of Bi-213 From The Activity Ac-225 Source

    DOEpatents

    Egorov, Oleg B.; O'Hara, Matthew J.

    2005-12-06

    A method and apparatus for isolating and purifying a .sup.213 Bi radioactive isotope from an .sup.225 Ac source using a primary column and a primary sorbent which preferentially retains .sup.225 Ac over .sup.213 Bi when exposed to a compatible solvent in combination with a secondary column having a secondary sorbent which retains .sup.213 Bi when exposed to a mixture of the compatible solvent and .sup.213 Bi. A "compatible solvent" is a solvent which will preferentially remove .sup.213 Bi radioactive isotopes from a primary sorbent without removing .sup.225 Ac radioactive isotopes, and then allow .sup.213 Bi radioactive isotopes removed from the primary sorbent to be retained on a secondary sorbent, without having to dilute or otherwise chemically or physically modify the compatible solvent in between exposure to the primary and secondary sorbents.

  16. Distribution of AC loss in a HTS magnet for SMES with different operating conditions

    NASA Astrophysics Data System (ADS)

    Xu, Y.; Tang, Y.; Ren, L.; Jiao, F.; Song, M.; Cao, K.; Wang, D.; Wang, L.; Dong, H.

    2013-11-01

    The AC loss induced in superconducting tape may affect the performance of a superconducting device applied to power system, such as transformer, cable, motor and even Superconducting Magnetic Energy Storage (SMES). The operating condition of SMES is changeable due to the need of compensation to the active or reactive power according to the demand of a power grid. In this paper, it is investigated that the distribution of AC loss for a storage magnet on different operating conditions, which is based on finite element method (FEM) and measured properties of BSCCO/Ag tapes. This analytical method can be used to optimize the SMES magnet.

  17. Negative hydrogen ion beam extraction from an AC heated cathode driven Bernas-type ion source

    SciTech Connect

    Okano, Y.; Miyamoto, N.; Kasuya, T.; Wada, M.

    2015-04-08

    A plasma grid structure was installed to a Bernas-type ion source used for ion implantation equipment. A negative hydrogen (H{sup −}) ion beam was extracted by an AC driven ion source by adjusting the bias to the plasma grid. The extracted electron current was reduced by positively biasing the plasma grid, while an optimum plasma grid bias voltage for negative ion beam extraction was found to be positive 3 V with respect to the arc chamber. Source operations with AC cathode heating show extraction characteristics almost identical to that with DC cathode heating, except a minute increase in H{sup −} current at higher frequency of cathode heating current.

  18. Carbon source-dependent regulation of the acetyl-coenzyme A synthetase-encoding gene ACS1 from Saccharomyces cerevisiae.

    PubMed

    Kratzer, S; Schüller, H J

    1995-08-01

    The yeast ACS1 gene, encoding acetyl-coenzyme A synthetase (ACS), was cloned using colony hybridization and a facA probe from Aspergillus nidulans. The complete sequence of 1.5 kb of the ACS1 upstream region was determined. Northern hybridization revealed a strong depression of ACS1 transcripts in a strain grown on the nonfermentable carbon sources, acetate or ethanol. In contrast to a previous report, delta acs1 null mutants did not exhibit a growth defect on acetate medium. Indeed, enzyme assays showed the presence of an additional constitutively expressed ACS activity in delta acs1 mutants. The carbon source-dependent expression was further investigated by the use of an ACS1::lacZ fusion gene, showing complete repression on easily fermentable sugars such as glucose, maltose, sucrose or galactose. Binding sites for the yeast general regulatory factors, Abf1p and Reb1p, together with a sequence reminiscent of the recently identified carbon source-responsive element (CSRE), could be detected in the ACS1 upstream region, presumably mediating the observed regulatory phenotype of this ACS isoenzyme. PMID:7642141

  19. Oblique electromagnetic electron cyclotron waves for Kappa distribution with AC field in planetary magnetospheres

    NASA Astrophysics Data System (ADS)

    Pandey, R. S.; Kaur, Rajbir

    2015-08-01

    The dispersion relation for obliquely propagating relativistic electromagnetic electron cyclotron (EMEC) waves in collision-less magnetoplasma is obtained. Investigations for EMEC waves in magnetosphere of Jupiter, Saturn and Uranus have been done, in presence of perpendicular AC electric field for Kappa distribution function. The relativistic temporal growth rate is calculated using method of characteristic solution. Using the data provided by spacecrafts like Cassini, Voyager 1 and 2, while exploring the magnetosphere of Jupiter, Saturn and Uranus, is used to plot graphs showing growth rate being effected by various parameters. Comprehensive parametric analysis have been done at different radial distances of the planets. It is concluded that beside huge difference in magnetospheric configuration, temperature anisotropy remains the main source of energy in case of Jupiter and Uranus. While studying EMEC waves in magnetosphere of Saturn, it is inferred that growth rate attains maximum magnitude when angle of propagation increases. Also, the results and its interpretations explain how the growth of EMEC wave modifies in different magnetospheric conditions.

  20. Distributed Power Sources for Mars Colonization

    NASA Astrophysics Data System (ADS)

    Miley, George H.; Shaban, Yasser

    2003-01-01

    One of the fundamental needs for Mars colonization is an abundant source of energy. The total energy system will probably use a mixture of sources based on solar energy, fuel cells, and nuclear energy. Here we concentrate on the possibility of developing a distributed system employing several unique new types of nuclear energy sources, specifically small fusion devices using inertial electrostatic confinement and portable ``battery type'' proton reaction cells.

  1. Bulk data transfer distributer: a high performance multicast model in ALMA ACS

    NASA Astrophysics Data System (ADS)

    Cirami, R.; Di Marcantonio, P.; Chiozzi, G.; Jeram, B.

    2006-06-01

    A high performance multicast model for the bulk data transfer mechanism in the ALMA (Atacama Large Millimeter Array) Common Software (ACS) is presented. The ALMA astronomical interferometer will consist of at least 50 12-m antennas operating at millimeter wavelength. The whole software infrastructure for ALMA is based on ACS, which is a set of application frameworks built on top of CORBA. To cope with the very strong requirements for the amount of data that needs to be transported by the software communication channels of the ALMA subsystems (a typical output data rate expected from the Correlator is of the order of 64 MB per second) and with the potential CORBA bottleneck due to parameter marshalling/de-marshalling, usage of IIOP protocol, etc., a transfer mechanism based on the ACE/TAO CORBA Audio/Video (A/V) Streaming Service has been developed. The ACS Bulk Data Transfer architecture bypasses the CORBA protocol with an out-of-bound connection for the data streams (transmitting data directly in TCP or UDP format), using at the same time CORBA for handshaking and leveraging the benefits of ACS middleware. Such a mechanism has proven to be capable of high performances, of the order of 800 Mbits per second on a 1Gbit Ethernet network. Besides a point-to-point communication model, the ACS Bulk Data Transfer provides a multicast model. Since the TCP protocol does not support multicasting and all the data must be correctly delivered to all ALMA subsystems, a distributer mechanism has been developed. This paper focuses on the ACS Bulk Data Distributer, which mimics a multicast behaviour managing data dispatching to all receivers willing to get data from the same sender.

  2. Spiral arms as cosmic ray source distributions

    NASA Astrophysics Data System (ADS)

    Werner, M.; Kissmann, R.; Strong, A. W.; Reimer, O.

    2015-04-01

    The Milky Way is a spiral galaxy with (or without) a bar-like central structure. There is evidence that the distribution of suspected cosmic ray sources, such as supernova remnants, are associated with the spiral arm structure of galaxies. It is yet not clearly understood what effect such a cosmic ray source distribution has on the particle transport in our Galaxy. We investigate and measure how the propagation of Galactic cosmic rays is affected by a cosmic ray source distribution associated with spiral arm structures. We use the PICARD code to perform high-resolution 3D simulations of electrons and protons in galactic propagation scenarios that include four-arm and two-arm logarithmic spiral cosmic ray source distributions with and without a central bar structure as well as the spiral arm configuration of the NE2001 model for the distribution of free electrons in the Milky Way. Results of these simulation are compared to an axisymmetric radial source distribution. Also, effects on the cosmic ray flux and spectra due to different positions of the Earth relative to the spiral structure are studied. We find that high energy electrons are strongly confined to their sources and the obtained spectra largely depend on the Earth's position relative to the spiral arms. Similar finding have been obtained for low energy protons and electrons albeit at smaller magnitude. We find that even fractional contributions of a spiral arm component to the total cosmic ray source distribution influences the spectra on the Earth. This is apparent when compared to an axisymmetric radial source distribution as well as with respect to the Earth's position relative to the spiral arm structure. We demonstrate that the presence of a Galactic bar manifests itself as an overall excess of low energy electrons at the Earth. Using a spiral arm geometry as a cosmic ray source distributions offers a genuine new quality of modeling and is used to explain features in cosmic ray spectra at the Earth

  3. Over-Distribution in Source Memory

    PubMed Central

    Brainerd, C. J.; Reyna, V. F.; Holliday, R. E.; Nakamura, K.

    2012-01-01

    Semantic false memories are confounded with a second type of error, over-distribution, in which items are attributed to contradictory episodic states. Over-distribution errors have proved to be more common than false memories when the two are disentangled. We investigated whether over-distribution is prevalent in another classic false memory paradigm: source monitoring. It is. Conventional false memory responses (source misattributions) were predominantly over-distribution errors, but unlike semantic false memory, over-distribution also accounted for more than half of true memory responses (correct source attributions). Experimental control of over-distribution was achieved via a series of manipulations that affected either recollection of contextual details or item memory (concreteness, frequency, list-order, number of presentation contexts, and individual differences in verbatim memory). A theoretical model was used to analyze the data (conjoint process dissociation) that predicts that predicts that (a) over-distribution is directly proportional to item memory but inversely proportional to recollection and (b) item memory is not a necessary precondition for recollection of contextual details. The results were consistent with both predictions. PMID:21942494

  4. AC current distribution and losses in multifilamentary superconductors exposed to longitudinal magnetic field

    SciTech Connect

    Le Naour, S.; Lacaze, A.; Laumond, Y.; Estop, P.; Verhaege, T.

    1996-07-01

    The current distribution and also AC losses, in a multifilamentary superconductor carrying a transport current, are influenced by the self and the external magnetic field. By using the Maxwell equations, a model has been developed in order to calculate the temporal evolution of current distribution in a single wire exposed or not to external magnetic field. This model is based on the actual relationship of electrical field E with current density J and takes into account the twist pitch of the wire. AC losses are calculated by adding all local losses through the cross section. This paper presents calculations of the influence of the cable twist coupled with the longitudinal magnetic field, and also gives some ideas how to decrease losses.

  5. Development of an AC power source for CSEM method using full-bridge switching configuration

    NASA Astrophysics Data System (ADS)

    Indrasari, Widyaningrum; Srigutomo, Wahyu; Djamal, Mitra; S, Rahmondia N.

    2015-04-01

    The electromagnetic (EM) method has been widely used in geophysical surveys. It is a non-destructive method that utilizes electromagnetic waves in characterizing subsurface profiles. Generally, EM method can be divided into passive EM and active EM. The passive EM uses the natural electromagnetic field sources, while the active EM or Controlled Source EM (CSEM) uses artificial source to generate electromagnetic wave. In this paper, we present the development of AC power source for CSEM transmitter. As the power source we used AC source with sine wave signal. To satisfy a high power and high voltage in the equipment, we used the full-bridge configuration switching. It works on 990 Hz maximum frequency, and can deliver maximum current of 1.9 A at 620 V. The switching is controlled by microcontroller using Pulse Width Modulation (PWM) and the driver of inverter is built using IGBT. The output frequency can be varied from 1 Hz to 990 Hz. For varied frequencies the harmonic distortion is different due to switching speed. As frequency increase the harmonic distortion also increase. We found that the total harmonic distortion can be reduced to 1 % at the output with 330 Hz.

  6. THE HST/ACS COMA CLUSTER SURVEY. II. DATA DESCRIPTION AND SOURCE CATALOGS

    SciTech Connect

    Hammer, Derek; Verdoes Kleijn, Gijs; Den Brok, Mark; Peletier, Reynier F.; Hoyos, Carlos; Balcells, Marc; Aguerri, Alfonso L.; Ferguson, Henry C.; Goudfrooij, Paul; Carter, David; Guzman, Rafael; Smith, Russell J.; Lucey, John R.; Graham, Alister W.; Trentham, Neil; Peng, Eric; Puzia, Thomas H.; Jogee, Shardha; Batcheldor, Dan; Bridges, Terry J.

    2010-11-15

    The Coma cluster, Abell 1656, was the target of an HST-ACS Treasury program designed for deep imaging in the F475W and F814W passbands. Although our survey was interrupted by the ACS instrument failure in early 2007, the partially completed survey still covers {approx}50% of the core high-density region in Coma. Observations were performed for 25 fields that extend over a wide range of cluster-centric radii ({approx}1.75 Mpc or 1{sup 0}) with a total coverage area of 274 arcmin{sup 2}. The majority of the fields are located near the core region of Coma (19/25 pointings) with six additional fields in the southwest region of the cluster. In this paper, we present reprocessed images and SEXTRACTOR source catalogs for our survey fields, including a detailed description of the methodology used for object detection and photometry, the subtraction of bright galaxies to measure faint underlying objects, and the use of simulations to assess the photometric accuracy and completeness of our catalogs. We also use simulations to perform aperture corrections for the SEXTRACTOR Kron magnitudes based only on the measured source flux and its half-light radius. We have performed photometry for {approx}73,000 unique objects; approximately one-half of our detections are brighter than the 10{sigma} point-source detection limit at F814W = 25.8 mag (AB). The slight majority of objects (60%) are unresolved or only marginally resolved by ACS. We estimate that Coma members are 5%-10% of all source detections, which consist of a large population of unresolved compact sources (primarily globular clusters but also ultra-compact dwarf galaxies) and a wide variety of extended galaxies from a cD galaxy to dwarf low surface brightness galaxies. The red sequence of Coma member galaxies has a color-magnitude relation with a constant slope and dispersion over 9 mag (-21 < M {sub F814W} < -13). The initial data release for the HST-ACS Coma Treasury program was made available to the public in 2008

  7. Distributed transform coding via source-splitting

    NASA Astrophysics Data System (ADS)

    Yahampath, Pradeepa

    2012-12-01

    Transform coding (TC) is one of the best known practical methods for quantizing high-dimensional vectors. In this article, a practical approach to distributed TC of jointly Gaussian vectors is presented. This approach, referred to as source-split distributed transform coding (SP-DTC), can be used to easily implement two terminal transform codes for any given rate-pair. The main idea is to apply source-splitting using orthogonal-transforms, so that only Wyner-Ziv (WZ) quantizers are required for compression of transform coefficients. This approach however requires optimizing the bit allocation among dependent sets of WZ quantizers. In order to solve this problem, a low-complexity tree-search algorithm based on analytical models for transform coefficient quantization is developed. A rate-distortion (RD) analysis of SP-DTCs for jointly Gaussian sources is presented, which indicates that these codes can significantly outperform the practical alternative of independent TC of each source, whenever there is a strong correlation between the sources. For practical implementation of SP-DTCs, the idea of using conditional entropy constrained (CEC) quantizers followed by Slepian-Wolf coding is explored. Experimental results obtained with SP-DTC designs based on both CEC scalar quantizers and CEC trellis-coded quantizers demonstrate that actual implementations of SP-DTCs can achieve RD performance close to the analytically predicted limits.

  8. Calculation of external dose from distributed source

    SciTech Connect

    Kocher, D.C.

    1986-01-01

    This paper discusses a relatively simple calculational method, called the point kernel method (Fo68), for estimating external dose from distributed sources that emit photon or electron radiations. The principles of the point kernel method are emphasized, rather than the presentation of extensive sets of calculations or tables of numerical results. A few calculations are presented for simple source geometries as illustrations of the method, and references and descriptions are provided for other caluclations in the literature. This paper also describes exposure situations for which the point kernel method is not appropriate and other, more complex, methods must be used, but these methods are not discussed in any detail.

  9. Open Source Live Distributions for Computer Forensics

    NASA Astrophysics Data System (ADS)

    Giustini, Giancarlo; Andreolini, Mauro; Colajanni, Michele

    Current distributions of open source forensic software provide digital investigators with a large set of heterogeneous tools. Their use is not always focused on the target and requires high technical expertise. We present a new GNU/Linux live distribution, named CAINE (Computer Aided INvestigative Environment) that contains a collection of tools wrapped up into a user friendly environment. The CAINE forensic framework introduces novel important features, aimed at filling the interoperability gap across different forensic tools. Moreover, it provides a homogeneous graphical interface that drives digital investigators during the acquisition and analysis of electronic evidence, and it offers a semi-automatic mechanism for the creation of the final report.

  10. Voltage source ac-to-dc converters for high-power transmitters

    NASA Technical Reports Server (NTRS)

    Cormier, R.

    1990-01-01

    This work was done to optimize the design of the components used for the beam power supply, which is a component of the transmitters in the Deep Space Network (DSN). The major findings are: (1) the difference in regulation between a six-pulse and a twelve-pulse converter is at most 7 percent worse for the twelve-pulse converter; (2) the commutation overlap angle of a current source converter equals that of a voltage source converter with continuous line currents; (3) the sources of uncharacteristic harmonics are identified with SPICE simulation; (4) the use of an imperfect phase-shifting transformer for the twelve-pulse converter generates a harmonic at six times the line frequency; and (5) the assumptions usually made in analyzing converters can be relaxed with SPICE simulation. The results demonstrate the suitability of using SPICE simulation to obtain detailed performance predictions of ac-to-dc converters.

  11. Sensitivity analysis of distributed volcanic source inversion

    NASA Astrophysics Data System (ADS)

    Cannavo', Flavio; Camacho, Antonio G.; González, Pablo J.; Puglisi, Giuseppe; Fernández, José

    2016-04-01

    A recently proposed algorithm (Camacho et al., 2011) claims to rapidly estimate magmatic sources from surface geodetic data without any a priori assumption about source geometry. The algorithm takes the advantages of fast calculation from the analytical models and adds the capability to model free-shape distributed sources. Assuming homogenous elastic conditions, the approach can determine general geometrical configurations of pressured and/or density source and/or sliding structures corresponding to prescribed values of anomalous density, pressure and slip. These source bodies are described as aggregation of elemental point sources for pressure, density and slip, and they fit the whole data (keeping some 3D regularity conditions). Although some examples and applications have been already presented to demonstrate the ability of the algorithm in reconstructing a magma pressure source (e.g. Camacho et al., 2011,Cannavò et al., 2015), a systematic analysis of sensitivity and reliability of the algorithm is still lacking. In this explorative work we present results from a large statistical test designed to evaluate the advantages and limitations of the methodology by assessing its sensitivity to the free and constrained parameters involved in inversions. In particular, besides the source parameters, we focused on the ground deformation network topology, and noise in measurements. The proposed analysis can be used for a better interpretation of the algorithm results in real-case applications. Camacho, A. G., González, P. J., Fernández, J. & Berrino, G. (2011) Simultaneous inversion of surface deformation and gravity changes by means of extended bodies with a free geometry: Application to deforming calderas. J. Geophys. Res. 116. Cannavò F., Camacho A.G., González P.J., Mattia M., Puglisi G., Fernández J. (2015) Real Time Tracking of Magmatic Intrusions by means of Ground Deformation Modeling during Volcanic Crises, Scientific Reports, 5 (10970) doi:10.1038/srep

  12. Particle size distribution of indoor aerosol sources

    SciTech Connect

    Shah, K.B.

    1990-10-24

    As concern about Indoor Air Quality (IAQ) has grown in recent years, it has become necessary to determine the nature of particles produced by different indoor aerosol sources and the typical concentration that these sources tend to produce. These data are important in predicting the dose of particles to people exposed to these sources and it will also enable us to take effective mitigation procedures. Further, it will also help in designing appropriate air cleaners. A new state of the art technique, DMPS (Differential Mobility Particle Sizer) System is used to determine the particle size distributions of a number of sources. This system employs the electrical mobility characteristics of these particles and is very effective in the 0.01--1.0 {mu}m size range. A modified system that can measure particle sizes in the lower size range down to 3 nm was also used. Experimental results for various aerosol sources is presented in the ensuing chapters. 37 refs., 20 figs., 2 tabs.

  13. Quantum key distribution with entangled photon sources

    NASA Astrophysics Data System (ADS)

    Ma, Xiongfeng; Fung, Chi-Hang Fred; Lo, Hoi-Kwong

    2007-07-01

    A parametric down-conversion (PDC) source can be used as either a triggered single-photon source or an entangled-photon source in quantum key distribution (QKD). The triggering PDC QKD has already been studied in the literature. On the other hand, a model and a post-processing protocol for the entanglement PDC QKD are still missing. We fill in this important gap by proposing such a model and a post-processing protocol for the entanglement PDC QKD. Although the PDC model is proposed to study the entanglement-based QKD, we emphasize that our generic model may also be useful for other non-QKD experiments involving a PDC source. Since an entangled PDC source is a basis-independent source, we apply Koashi and Preskill’s security analysis to the entanglement PDC QKD. We also investigate the entanglement PDC QKD with two-way classical communications. We find that the recurrence scheme increases the key rate and the Gottesman-Lo protocol helps tolerate higher channel losses. By simulating a recent 144-km open-air PDC experiment, we compare three implementations: entanglement PDC QKD, triggering PDC QKD, and coherent-state QKD. The simulation result suggests that the entanglement PDC QKD can tolerate higher channel losses than the coherent-state QKD. The coherent-state QKD with decoy states is able to achieve highest key rate in the low- and medium-loss regions. By applying the Gottesman-Lo two-way post-processing protocol, the entanglement PDC QKD can tolerate up to 70dB combined channel losses ( 35dB for each channel) provided that the PDC source is placed in between Alice and Bob. After considering statistical fluctuations, the PDC setup can tolerate up to 53dB channel losses.

  14. The HST/ACS Coma Cluster Survey. II. Data Description and Source Catalogs

    NASA Technical Reports Server (NTRS)

    Hammer, Derek; Kleijn, Gijs Verdoes; Hoyos, Carlos; Den Brok, Mark; Balcells, Marc; Ferguson, Henry C.; Goudfrooij, Paul; Carter, David; Guzman, Rafael; Peletier, Reynier F.; Smith, Russell J.; Graham, Alister W.; Trentham, Neil; Peng, Eric; Puzia, Thomas H.; Lucey, John R.; Jogee, Shardha; Aguerri, Alfonso L.; Batcheldor, Dan; Bridges, Terry J.; Davies, Jonathan I.; Del Burgo, Carlos; Erwin, Peter; Hornschemeier, Ann; Hudson, Michael J.

    2010-01-01

    The Coma cluster, Abell 1656, was the target of a HST-ACS Treasury program designed for deep imaging in the F475W and F814W passbands. Although our survey was interrupted by the ACS instrument failure in early 2007, the partially-completed survey still covers approximately 50% of the core high density region in Coma. Observations were performed for twenty-five fields with a total coverage area of 274 aremin(sup 2), and extend over a wide range of cluster-centric radii (approximately 1.75 Mpe or 1 deg). The majority of the fields are located near the core region of Coma (19/25 pointings) with six additional fields in the south-west region of the cluster. In this paper we present SEXTRACTOR source catalogs generated from the processed images, including a detailed description of the methodology used for object detection and photometry, the subtraction of bright galaxies to measure faint underlying objects, and the use of simulations to assess the photometric accuracy and completeness of our catalogs. We also use simulations to perform aperture corrections for the SEXTRACTOR Kron magnitudes based only on the measured source flux and its half-light radius. We have performed photometry for 76,000 objects that consist of roughly equal numbers of extended galaxies and unresolved objects. Approximately two-thirds of all detections are brighter than F814W=26.5 mag (AB), which corresponds to the 10sigma, point-source detection limit. We estimate that Coma members are 5-10% of the source detections, including a large population of compact objects (primarily GCs, but also cEs and UCDs), and a wide variety of extended galaxies from cD galaxies to dwarf low surface brightness galaxies. The initial data release for the HST-ACS Coma Treasury program was made available to the public in August 2008. The images and catalogs described in this study relate to our second data release.

  15. Experimental quantum key distribution with source flaws

    NASA Astrophysics Data System (ADS)

    Xu, Feihu; Wei, Kejin; Sajeed, Shihan; Kaiser, Sarah; Sun, Shihai; Tang, Zhiyuan; Qian, Li; Makarov, Vadim; Lo, Hoi-Kwong

    2015-09-01

    Decoy-state quantum key distribution (QKD) is a standard technique in current quantum cryptographic implementations. Unfortunately, existing experiments have two important drawbacks: the state preparation is assumed to be perfect without errors and the employed security proofs do not fully consider the finite-key effects for general attacks. These two drawbacks mean that existing experiments are not guaranteed to be proven to be secure in practice. Here, we perform an experiment that shows secure QKD with imperfect state preparations over long distances and achieves rigorous finite-key security bounds for decoy-state QKD against coherent attacks in the universally composable framework. We quantify the source flaws experimentally and demonstrate a QKD implementation that is tolerant to channel loss despite the source flaws. Our implementation considers more real-world problems than most previous experiments, and our theory can be applied to general discrete-variable QKD systems. These features constitute a step towards secure QKD with imperfect devices.

  16. High power distributed x-ray source

    NASA Astrophysics Data System (ADS)

    Frutschy, Kris; Neculaes, Bogdan; Inzinna, Lou; Caiafa, Antonio; Reynolds, Joe; Zou, Yun; Zhang, Xi; Gunturi, Satish; Cao, Yang; Waters, Bill; Wagner, Dave; De Man, Bruno; McDevitt, Dan; Roffers, Rick; Lounsberry, Brian; Pelc, Norbert J.

    2010-04-01

    This paper summarizes the development of a distributed x-ray source with up to 60kW demonstrated instantaneous power. Component integration and test results are shown for the dispenser cathode electron gun, fast switching controls, high voltage stand-off insulator, brazed anode, and vacuum system. The current multisource prototype has been operated for over 100 hours without failure, and additional testing is needed to discover the limiting component. Example focal spot measurements and x-ray radiographs are included. Lastly, future development opportunities are highlighted.

  17. Nonlinear control of voltage source converters in AC-DC power system.

    PubMed

    Dash, P K; Nayak, N

    2014-07-01

    This paper presents the design of a robust nonlinear controller for a parallel AC-DC power system using a Lyapunov function-based sliding mode control (LYPSMC) strategy. The inputs for the proposed control scheme are the DC voltage and reactive power errors at the converter station and the active and reactive power errors at the inverter station of the voltage-source converter-based high voltage direct current transmission (VSC-HVDC) link. The stability and robust tracking of the system parameters are ensured by applying the Lyapunov direct method. Also the gains of the sliding mode control (SMC) are made adaptive using the stability conditions of the Lyapunov function. The proposed control strategy offers invariant stability to a class of systems having modeling uncertainties due to parameter changes and exogenous inputs. Comprehensive computer simulations are carried out to verify the proposed control scheme under several system disturbances like changes in short-circuit ratio, converter parametric changes, and faults on the converter and inverter buses for single generating system connected to the power grid in a single machine infinite-bus AC-DC network and also for a 3-machine two-area power system. Furthermore, a second order super twisting sliding mode control scheme has been presented in this paper that provides a higher degree of nonlinearity than the LYPSMC and damps faster the converter and inverter voltage and power oscillations. PMID:24906895

  18. CONSTRAINING SOURCE REDSHIFT DISTRIBUTIONS WITH GRAVITATIONAL LENSING

    SciTech Connect

    Wittman, D.; Dawson, W. A.

    2012-09-10

    We introduce a new method for constraining the redshift distribution of a set of galaxies, using weak gravitational lensing shear. Instead of using observed shears and redshifts to constrain cosmological parameters, we ask how well the shears around clusters can constrain the redshifts, assuming fixed cosmological parameters. This provides a check on photometric redshifts, independent of source spectral energy distribution properties and therefore free of confounding factors such as misidentification of spectral breaks. We find that {approx}40 massive ({sigma}{sub v} = 1200 km s{sup -1}) cluster lenses are sufficient to determine the fraction of sources in each of six coarse redshift bins to {approx}11%, given weak (20%) priors on the masses of the highest-redshift lenses, tight (5%) priors on the masses of the lowest-redshift lenses, and only modest (20%-50%) priors on calibration and evolution effects. Additional massive lenses drive down uncertainties as N{sub lens}{sup -1/2}, but the improvement slows as one is forced to use lenses further down the mass function. Future large surveys contain enough clusters to reach 1% precision in the bin fractions if the tight lens-mass priors can be maintained for large samples of lenses. In practice this will be difficult to achieve, but the method may be valuable as a complement to other more precise methods because it is based on different physics and therefore has different systematic errors.

  19. Distribution and Metabolism of Bt-Cry1Ac Toxin in Tissues and Organs of the Cotton Bollworm, Helicoverpa armigera

    PubMed Central

    Zhao, Zhuoya; Li, Yunhe; Xiao, Yutao; Ali, Abid; Dhiloo, Khalid Hussain; Chen, Wenbo; Wu, Kongming

    2016-01-01

    Crystal (Cry) proteins derived from Bacillus thuringiensis (Bt) have been widely used in transgenic crops due to their toxicity against insect pests. However, the distribution and metabolism of these toxins in insect tissues and organs have remained obscure because the target insects do not ingest much toxin. In this study, several Cry1Ac-resistant strains of Helicoverpa armigera, fed artificial diets containing high doses of Cry1Ac toxin, were used to investigate the distribution and metabolism of Cry1Ac in their bodies. Cry1Ac was only detected in larvae, not in pupae or adults. Also, Cry1Ac passed through the midgut into other tissues, such as the hemolymph and fat body, but did not reach the larval integument. Metabolic tests revealed that Cry1Ac degraded most rapidly in the fat body, followed by the hemolymph, peritrophic membrane and its contents. The toxin was metabolized slowly in the midgut, but was degraded in all locations within 48 h. These findings will improve understanding of the functional mechanism of Bt toxins in target insects and the biotransfer and the bioaccumulation of Bt toxins in arthropod food webs in the Bt crop ecosystem. PMID:27399776

  20. Distribution and Metabolism of Bt-Cry1Ac Toxin in Tissues and Organs of the Cotton Bollworm, Helicoverpa armigera.

    PubMed

    Zhao, Zhuoya; Li, Yunhe; Xiao, Yutao; Ali, Abid; Dhiloo, Khalid Hussain; Chen, Wenbo; Wu, Kongming

    2016-01-01

    Crystal (Cry) proteins derived from Bacillus thuringiensis (Bt) have been widely used in transgenic crops due to their toxicity against insect pests. However, the distribution and metabolism of these toxins in insect tissues and organs have remained obscure because the target insects do not ingest much toxin. In this study, several Cry1Ac-resistant strains of Helicoverpa armigera, fed artificial diets containing high doses of Cry1Ac toxin, were used to investigate the distribution and metabolism of Cry1Ac in their bodies. Cry1Ac was only detected in larvae, not in pupae or adults. Also, Cry1Ac passed through the midgut into other tissues, such as the hemolymph and fat body, but did not reach the larval integument. Metabolic tests revealed that Cry1Ac degraded most rapidly in the fat body, followed by the hemolymph, peritrophic membrane and its contents. The toxin was metabolized slowly in the midgut, but was degraded in all locations within 48 h. These findings will improve understanding of the functional mechanism of Bt toxins in target insects and the biotransfer and the bioaccumulation of Bt toxins in arthropod food webs in the Bt crop ecosystem. PMID:27399776

  1. HST/ACS IMAGING OF OMEGA CENTAURI: OPTICAL COUNTERPARTS OF CHANDRA X-RAY SOURCES

    SciTech Connect

    Cool, Adrienne M.; Arias, Tersi; Brochmann, Michelle; Dorfman, Jason; Gafford, April; White, Vivian; Haggard, Daryl; Anderson, Jay E-mail: dhaggard@northwestern.edu

    2013-02-15

    We present results of a search for optical counterparts of X-ray sources in and toward the globular cluster Omega Centauri (NGC 5139) using the Advanced Camera for Surveys (ACS) on the Hubble Space Telescope. The ACS data consist of a mosaic of Wide Field Channel images obtained using F625W, F435W, and F658N filters; with nine pointings we cover the central {approx}10' Multiplication-Sign 10' of the cluster and encompass 109 known Chandra sources. We find promising optical counterparts for 59 of the sources, {approx}40 of which are likely to be associated with the cluster. These include 27 candidate cataclysmic variables (CVs), 24 of which are reported here for the first time. Fourteen of the CV candidates are very faint, with absolute magnitudes in the range M {sub 625} =10.4-12.6, making them comparable in brightness to field CVs near the period minimum discovered in the Sloan Digital Sky Survey. Additional optical counterparts include three BY Dra candidates, a possible blue straggler, and a previously reported quiescent low-mass X-ray binary. We also identify 3 foreground stars and 11 probable active galactic nuclei. Finally, we report the discovery of a group of seven stars whose X-ray properties are suggestive of magnetically active binaries, and whose optical counterparts lie on or very near the metal-rich anomalous giant and subgiant branches in {omega} Cen. If the apparent association between these seven stars and the RGB/SGB-a stars is real, then the frequency of X-ray sources in this metal-rich population is enhanced by a factor of at least five relative to the other giant and subgiant populations in the cluster. If these stars are not members of the metal-rich population, then they bring the total number of red stragglers (also known as sub-subgiants) that have been identified in {omega} to Cen 20, the largest number yet known in any globular cluster.

  2. Panchromatic spectral energy distributions of Herschel sources

    NASA Astrophysics Data System (ADS)

    Berta, S.; Lutz, D.; Santini, P.; Wuyts, S.; Rosario, D.; Brisbin, D.; Cooray, A.; Franceschini, A.; Gruppioni, C.; Hatziminaoglou, E.; Hwang, H. S.; Le Floc'h, E.; Magnelli, B.; Nordon, R.; Oliver, S.; Page, M. J.; Popesso, P.; Pozzetti, L.; Pozzi, F.; Riguccini, L.; Rodighiero, G.; Roseboom, I.; Scott, D.; Symeonidis, M.; Valtchanov, I.; Viero, M.; Wang, L.

    2013-03-01

    Combining far-infrared Herschel photometry from the PACS Evolutionary Probe (PEP) and Herschel Multi-tiered Extragalactic Survey (HerMES) guaranteed time programs with ancillary datasets in the GOODS-N, GOODS-S, and COSMOS fields, it is possible to sample the 8-500 μm spectral energy distributions (SEDs) of galaxies with at least 7-10 bands. Extending to the UV, optical, and near-infrared, the number of bands increases up to 43. We reproduce the distribution of galaxies in a carefully selected restframe ten colors space, based on this rich data-set, using a superposition of multivariate Gaussian modes. We use this model to classify galaxies and build median SEDs of each class, which are then fitted with a modified version of the magphys code that combines stellar light, emission from dust heated by stars and a possible warm dust contribution heated by an active galactic nucleus (AGN). The color distribution of galaxies in each of the considered fields can be well described with the combination of 6-9 classes, spanning a large range of far- to near-infrared luminosity ratios, as well as different strength of the AGN contribution to bolometric luminosities. The defined Gaussian grouping is used to identify rare or odd sources. The zoology of outliers includes Herschel-detected ellipticals, very blue z ~ 1 Ly-break galaxies, quiescent spirals, and torus-dominated AGN with star formation. Out of these groups and outliers, a new template library is assembled, consisting of 32 SEDs describing the intrinsic scatter in the restframe UV-to-submm colors of infrared galaxies. This library is tested against L(IR) estimates with and without Herschel data included, and compared to eightother popular methods often adopted in the literature. When implementing Herschel photometry, these approaches produce L(IR) values consistent with each other within a median absolute deviation of 10-20%, the scatter being dominated more by fine tuning of the codes, rather than by the choice of

  3. Multi-Modality Pulsed AC Source for Medical Applications of Non-Equilibrium Plasmas

    NASA Astrophysics Data System (ADS)

    Friedrichs, Daniel; Gilbert, James

    2014-10-01

    A burgeoning field has developed around the use of non-equilibrium (``cold'') plasmas for various medical applications, including wound treatment, surface sterilization, non-thermal hemostasis, and selective cell destruction. Proposed devices typically utilize pulsed DC power sources, which have no other therapeutic utility, and may encounter significant regulatory restrictions regarding their safety for use in patient care. Additionally, dedicated capital equipment is difficult for healthcare facilities to justify. In this work, we have demonstrated for the first time the generation of non-equilibrium plasma using pulsed AC output from a specially-designed electrosurgical generator. The ability to power novel non-equilibrium plasma devices from a piece of equipment already ubiquitous in operating theatres should significantly reduce the barriers to adoption of plasma devices. We demonstrate the ability of a prototype device, coupled to this source, to reduce bacterial growth in vitro. Such a system could allow a single surgical instrument to provide both non-thermal sterilization and thermal tissue dissection.

  4. ac losses and field and current density distribution during a full cycle of a stack of superconducting tapes

    NASA Astrophysics Data System (ADS)

    Yuan, Weijia; Campbell, A. M.; Coombs, T. A.

    2010-05-01

    Starting from an existing model by Clem et al., this paper has analyzed how the current density and magnetic field distribution of a stack of superconducting tapes with ac transport currents or applied fields will change in a full cycle. This paper assumes when the ac current or field starts to change in the other direction, a new penetrated region will begin to penetrate from the superconductor surface. If we assume Jc is constant in the critical region, this paper demonstrates that the Claassen formula (7) can be used to calculate the exact ac losses. If Jc depends on local Bz, we can use Eq. (9) to quickly predict the ac losses. This approach does not need to calculate a complete ac cycle. This saves considerably computation time while gives a result which is in close agreement with that calculated from a complete ac cycle. The calculation method can be applied for calculating a superconducting pancake coil if the coil radius is much larger than the tape width.

  5. Achieving High Performance in AC-Field Driven Organic Light Sources

    PubMed Central

    Xu, Junwei; Carroll, David L.; Smith, Gregory M.; Dun, Chaochao; Cui, Yue

    2016-01-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m2 with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today’s OLEDs in performance. PMID:27063414

  6. Achieving High Performance in AC-Field Driven Organic Light Sources.

    PubMed

    Xu, Junwei; Carroll, David L; Smith, Gregory M; Dun, Chaochao; Cui, Yue

    2016-01-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m(2) with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today's OLEDs in performance. PMID:27063414

  7. Achieving High Performance in AC-Field Driven Organic Light Sources

    NASA Astrophysics Data System (ADS)

    Xu, Junwei; Carroll, David L.; Smith, Gregory M.; Dun, Chaochao; Cui, Yue

    2016-04-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m2 with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today’s OLEDs in performance.

  8. Power conversion distribution system using a resonant high-frequency AC link

    NASA Technical Reports Server (NTRS)

    Sood, P. K.; Lipo, T. A.

    1986-01-01

    Static power conversion systems based on a resonant high frequency (HF) link offers a significant reduction in the size and weight of the equipment over that achieved with conventional approaches, especially when multiple sources and loads are to be integrated. A faster system response and absence of audible noise are the other principal characteristics of such systems. A conversion configuration based on a HF link which is suitable for applications requiring distributed power is proposed.

  9. Problem solving as intelligent retrieval from distributed knowledge sources

    NASA Technical Reports Server (NTRS)

    Chen, Zhengxin

    1987-01-01

    Distributed computing in intelligent systems is investigated from a different perspective. From the viewpoint that problem solving can be viewed as intelligent knowledge retrieval, the use of distributed knowledge sources in intelligent systems is proposed.

  10. Causal Analysis of the Inadvertent Contact with an Uncontrolled Electrical Hazardous Energy Source (120 Volts AC)

    SciTech Connect

    David E. James; Dennis E. Raunig; Sean S. Cunningham

    2014-10-01

    On September 25, 2013, a Health Physics Technician (HPT) was performing preparations to support a pneumatic transfer from the HFEF Decon Cell to the Room 130 Glovebox in HFEF, per HFEF OI 3165 section 3.5, Field Preparations. This activity involves an HPT setting up and climbing a portable ladder to remove the 14-C meter probe from above ball valve HBV-7. The HPT source checks the meter and probe and then replaces the probe above HBV-7, which is located above Hood ID# 130 HP. At approximately 13:20, while reaching past the HBV-7 valve position indicator switches in an attempt to place the 14-C meter probe in the desired location, the HPT’s left forearm came in contact with one of the three sets of exposed terminals on the valve position indication switches for HBV 7. This resulted in the HPT receiving an electrical shock from a 120 Volt AC source. Upon moving the arm, following the electrical shock, the HPT noticed two exposed electrical connections on a switch. The HPT then notified the HFEF HPT Supervisor, who in turn notified the MFC Radiological Controls Manager and HFEF Operations Manager of the situation. Work was stopped in the area and the hazard was roped off and posted to prevent access to the hazard. The HPT was escorted by the HPT Supervisor to the MFC Dispensary and then preceded to CFA medical for further evaluation. The individual was evaluated and released without any medical restrictions. Causal Factor (Root Cause) A3B3C01/A5B2C08: - Knowledge based error/Attention was given to wrong issues - Written Communication content LTA, Incomplete/situation not covered The Causal Factor (root cause) was attention being given to the wrong issues during the creation, reviews, verifications, and actual performance of HFEF OI-3165, which covers the need to perform the weekly source check and ensure placement of the probe prior to performing a “rabbit” transfer. This resulted in the hazard not being identified and mitigated in the procedure. Work activities

  11. Body fat distribution in women with familial partial lipodystrophy caused by mutation in the lamin A/C gene

    PubMed Central

    Monteiro, Luciana Z.; Foss-Freitas, Maria C.; Júnior Montenegro, Renan M.; Foss, Milton C.

    2012-01-01

    Familial partial lipodystrophy (FPLD), Dunnigan variety, is an autosomal dominant disorder caused due to missense mutations in the lamin A/C (LMNA) gene encoding nuclear lamina proteins. Patients with FPLD are predisposed to metabolic complications of insulin resistance such as diabetes. We sought to evaluate and compare body fat distribution with dual-emission X-ray absorptiometry in women with and without FPLD and identify densitometric, clinical and metabolic features. PMID:22276265

  12. 14 CFR 23.1310 - Power source capacity and distribution.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Power source capacity and distribution. 23.1310 Section 23.1310 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Equipment General § 23.1310 Power source capacity and distribution. (a) Each installation whose...

  13. 14 CFR 23.1310 - Power source capacity and distribution.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Power source capacity and distribution. 23.1310 Section 23.1310 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Equipment General § 23.1310 Power source capacity and distribution. (a) Each installation whose...

  14. Open source portal to distributed image repositories

    NASA Astrophysics Data System (ADS)

    Tao, Wenchao; Ratib, Osman M.; Kho, Hwa; Hsu, Yung-Chao; Wang, Cun; Lee, Cason; McCoy, J. M.

    2004-04-01

    In large institution PACS, patient data may often reside in multiple separate systems. While most systems tend to be DICOM compliant, none of them offer the flexibility of seamless integration of multiple DICOM sources through a single access point. We developed a generic portal system with a web-based interactive front-end as well as an application programming interface (API) that allows both web users and client applications to query and retrieve image data from multiple DICOM sources. A set of software tools was developed to allow accessing several DICOM archives through a single point of access. An interactive web-based front-end allows user to search image data seamlessly from the different archives and display the results or route the image data to another DICOM compliant destination. An XML-based API allows other software programs to easily benefit from this portal to query and retrieve image data as well. Various techniques are employed to minimize the performance overhead inherent in the DICOM. The system is integrated with a hospital-wide HIPAA-compliant authentication and auditing service that provides centralized management of access to patient medical records. The system is provided under open source free licensing and developed using open-source components (Apache Tomcat for web server, MySQL for database, OJB for object/relational data mapping etc.). The portal paradigm offers a convenient and effective solution for accessing multiple image data sources in a given healthcare enterprise and can easily be extended to multi-institution through appropriate security and encryption mechanisms.

  15. Photocounting distributions for exponentially decaying sources.

    PubMed

    Teich, M C; Card, H C

    1979-05-01

    Exact photocounting distributions are obtained for a pulse of light whose intensity is exponentially decaying in time, when the underlying photon statistics are Poisson. It is assumed that the starting time for the sampling interval (which is of arbitrary duration) is uniformly distributed. The probability of registering n counts in the fixed time T is given in terms of the incomplete gamma function for n >/= 1 and in terms of the exponential integral for n = 0. Simple closed-form expressions are obtained for the count mean and variance. The results are expected to be of interest in certain studies involving spontaneous emission, radiation damage in solids, and nuclear counting. They will also be useful in neurobiology and psychophysics, since habituation and sensitization processes may sometimes be characterized by the same stochastic model. PMID:19687829

  16. Dose distributions in regions containing beta sources: Uniform spherical source regions in homogeneous media

    SciTech Connect

    Werner, B.L.; Rahman, M.; Salk, W.N. ); Kwok, C.S. )

    1991-11-01

    The energy-averaged transport model for the calculation of dose rate distributions is applied to uniform, spherical source distributions in homogeneous media for radii smaller than the electron range. The model agrees well with Monte Carlo based calculations for source distributions with radii greater than half the continuous slowing down approximation range. The dose rate distributions can be written in the medical internal radiation dose (MIRD) formalism.

  17. The source and distribution of Galactic positrons

    NASA Technical Reports Server (NTRS)

    Purcell, W. R.; Dixon, D. D.; Cheng, L.-X.; Leventhal, M.; Kinzer, R. L.; Kurfess, J. D.; Skibo, J. G.; Smith, D. M.; Tueller, J.

    1997-01-01

    The oriented scintillation spectrometer experiment (OSSE) observations of the Galactic plane and the Galactic center region were combined with observations acquired with other instruments in order to produce a map of the Galactic 511 keV annihilation radiation. Two mapping techniques were applied to the data: the maximum entropy method, and the basis pursuit inversion method. The resulting maps are qualitatively similar and show evidence for a central bulge and a weak galactic disk component. The weak disk is consistent with that expected from positrons produced by the decay of radioactive Al-26 in the interstellar medium. Both maps suggest an enhanced region of emission near l = -4 deg, b = 7 deg, with a flux of approximately 50 percent of that of the bulge. The existence of this emission appears significant, although the location is not well determined. The source of this enhanced emission is presently unknown.

  18. Tetrodotoxin: chemistry, toxicity, source, distribution and detection.

    PubMed

    Bane, Vaishali; Lehane, Mary; Dikshit, Madhurima; O'Riordan, Alan; Furey, Ambrose

    2014-02-01

    Tetrodotoxin (TTX) is a naturally occurring toxin that has been responsible for human intoxications and fatalities. Its usual route of toxicity is via the ingestion of contaminated puffer fish which are a culinary delicacy, especially in Japan. TTX was believed to be confined to regions of South East Asia, but recent studies have demonstrated that the toxin has spread to regions in the Pacific and the Mediterranean. There is no known antidote to TTX which is a powerful sodium channel inhibitor. This review aims to collect pertinent information available to date on TTX and its analogues with a special emphasis on the structure, aetiology, distribution, effects and the analytical methods employed for its detection. PMID:24566728

  19. Tetrodotoxin: Chemistry, Toxicity, Source, Distribution and Detection

    PubMed Central

    Bane, Vaishali; Lehane, Mary; Dikshit, Madhurima; O’Riordan, Alan; Furey, Ambrose

    2014-01-01

    Tetrodotoxin (TTX) is a naturally occurring toxin that has been responsible for human intoxications and fatalities. Its usual route of toxicity is via the ingestion of contaminated puffer fish which are a culinary delicacy, especially in Japan. TTX was believed to be confined to regions of South East Asia, but recent studies have demonstrated that the toxin has spread to regions in the Pacific and the Mediterranean. There is no known antidote to TTX which is a powerful sodium channel inhibitor. This review aims to collect pertinent information available to date on TTX and its analogues with a special emphasis on the structure, aetiology, distribution, effects and the analytical methods employed for its detection. PMID:24566728

  20. Sources and distributions of dark matter

    SciTech Connect

    Sikivie, P. |

    1995-12-31

    In the first section, the author tries to convey a sense of the variety of observational inputs that tell about the existence and the spatial distribution of dark matter in the universe. In the second section, he briefly reviews the four main dark matter candidates, taking note of each candidate`s status in the world of particle physics, its production in the early universe, its effect upon large scale structure formation and the means by which it may be detected. Section 3 concerns the energy spectrum of (cold) dark matter particles on earth as may be observed some day in a direct detection experiment. It is a brief account of work done in collaboration with J. Ipser and, more recently, with I. Tkachev and Y. Wang.

  1. I-BIEM calculations of the frequency dispersion and ac current distribution at disk and ring-disk electrodes

    NASA Technical Reports Server (NTRS)

    Cahan, Boris D.

    1991-01-01

    The Iterative Boundary Integral Equation Method (I-BIEM) has been applied to the problem of frequency dispersion at a disk electrode in a finite geometry. The I-BIEM permits the direct evaluation of the AC potential (a complex variable) using complex boundary conditions. The point spacing was made highly nonuniform, to give extremely high resolution in those regions where the variables change most rapidly, i.e., in the vicinity of the edge of the disk. Results are analyzed with respect to IR correction, equipotential surfaces, and reference electrode placement. The current distribution is also examined for a ring-disk configuration, with the ring and the disk at the same AC potential. It is shown that the apparent impedance of the disk is inductive at higher frequencies. The results are compared to analytic calculations from the literature, and usually agree to better than 0.001 percent.

  2. I-BIEM calculations of the frequency dispersion and AC current distribution at disk and ring-disk electrodes

    NASA Technical Reports Server (NTRS)

    Cahan, Boris D.

    1991-01-01

    The Iterative Boundary Integral Equation Method (I-BIEM) has been applied to the problem of frequency dispersion at a disk electrode in a finite geometry. The I-BIEM permits the direct evaluation of the AC potential (a complex variable) using complex boundary conditions. The point spacing was made highly nonuniform, to give extremely high resolution in those regions where the variables change most rapidly, i.e., in the vicinity of the edge of the disk. Results are analyzed with respect to IR correction, equipotential surfaces, and reference electrode placement. The current distribution is also examined for a ring-disk configuration, with the ring and the disk at the same AC potential. It is shown that the apparent impedance of the disk is inductive at higher frequencies. The results are compared to analytic calculations from the literature, and usually agree to better than 0.001 percent.

  3. Contamination on LDEF: Sources, distribution, and history

    NASA Technical Reports Server (NTRS)

    Pippin, Gary; Crutcher, Russ

    1993-01-01

    An introduction to contamination effects observed on the Long Duration Exposure Facility (LDEF) is presented. The activities reported are part of Boeing's obligation to the LDEF Materials Special Investigation Group. The contamination films and particles had minimal influence on the thermal performance of the LDEF. Some specific areas did have large changes in optical properties. Films also interfered with recession rate determination by reacting with the oxygen or physically shielding underlying material. Generally, contaminant films lessen the measured recession rate relative to 'clean' surfaces. On orbit generation of particles may be an issue for sensitive optics. Deposition on lenses may lead to artifacts on photographic images or cause sensors to respond inappropriately. Particles in the line of sight of sensors can cause stray light to be scattered into sensors. Particles also represent a hazard for mechanisms in that they can physically block and/or increase friction or wear on moving surfaces. LDEF carried a rather complex mixture of samples and support hardware into orbit. The experiments were assembled under a variety of conditions and time constraints and stored for up to five years before launch. The structure itself was so large that it could not be baked after the interior was painted with chemglaze Z-306 polyurethane based black paint. Any analysis of the effects of molecular and particulate contamination must account for a complex array of sources, wide variation in processes over time, and extreme variation in environment from ground to launch to flight. Surface conditions at certain locations on LDEF were established by outgassing of molecular species from particular materials onto adjacent surfaces, followed by alteration of those species due to exposure to atomic oxygen and/or solar radiation.

  4. Separating More Sources Than Sensors Using Time-Frequency Distributions

    NASA Astrophysics Data System (ADS)

    Linh-Trung, Nguyen; Belouchrani, Adel; Abed-Meraim, Karim; Boashash, Boualem

    2005-12-01

    We examine the problem of blind separation of nonstationary sources in the underdetermined case, where there are more sources than sensors. Since time-frequency (TF) signal processing provides effective tools for dealing with nonstationary signals, we propose a new separation method that is based on time-frequency distributions (TFDs). The underlying assumption is that the original sources are disjoint in the time-frequency (TF) domain. The successful method recovers the sources by performing the following four main procedures. First, the spatial time-frequency distribution (STFD) matrices are computed from the observed mixtures. Next, the auto-source TF points are separated from cross-source TF points thanks to the special structure of these mixture STFD matrices. Then, the vectors that correspond to the selected auto-source points are clustered into different classes according to the spatial directions which differ among different sources; each class, now containing the auto-source points of only one source, gives an estimation of the TFD of this source. Finally, the source waveforms are recovered from their TFD estimates using TF synthesis. Simulated experiments indicate the success of the proposed algorithm in different scenarios. We also contribute with two other modified versions of the algorithm to better deal with auto-source point selection.

  5. Adaptive Source Coding Schemes for Geometrically Distributed Integer Alphabets

    NASA Technical Reports Server (NTRS)

    Cheung, K-M.; Smyth, P.

    1993-01-01

    Revisit the Gallager and van Voorhis optimal source coding scheme for geometrically distributed non-negative integer alphabets and show that the various subcodes in the popular Rice algorithm can be derived from the Gallager and van Voorhis code.

  6. 14 CFR 25.1310 - Power source capacity and distribution.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... functioning normally. (2) Essential loads, after failure of any one prime mover, power converter, or energy... source of power is required, after any failure or malfunction in any one power supply system... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Power source capacity and distribution....

  7. 14 CFR 23.1310 - Power source capacity and distribution.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Power source capacity and distribution. 23.1310 Section 23.1310 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Equipment General § 23.1310 Power source...

  8. Time-resolved magnetic flux and AC-current distributions in superconducting yttrium barium copper oxide thin films and multifilaments

    NASA Astrophysics Data System (ADS)

    Yang, Ran

    Time-resolved magneto-optical imaging (TRMOI) technique allows dynamic ac transport measurements on superconductors. The high time and spatial resolutions of the measurements also offer good quantitative data analysis of the MO images. YBa2Cu 3O7-delta (YBCO) was discovered as a high-temperature superconductor (HTSC) which has wide applications due to its high critical temperature of Tc = 91 K, and high critical current density Jc in the order of 106-7 Acm-2. Many of the applications require high ac current load and a high magnetic field. We study the interaction behavior of YBCO thin films in an ac transport current and a dc magnetic field by the TRMOI technique. In this dissertation, I first introduce the applications of high-temperature superconductors with focus on YBCO and describe the advantages of the TRMOI technique we developed over other methods to map the magnetic flux distribution of superconductors. The theories to understand the magnetic properties of HTSC are presented, followed by theoretical models. I also introduce a newly developed finite elemental method (FEM) simulation which is proved to be a better theoretical guideline to our data analysis. The TRMOI experimental setup and the procedures are discussed in detail. I show step-by-step the calibration of light intensity profiles averaged from MO images to determine magnetic field distribution, and a numerical inversion of the Biot-Savart law to calculate the current density distributions. The current density evolution in YBCO thin films is studied by TRMOI as a function of the phase of an ac current applied simultaneously with a perpendicular dc magnetic field. The measurements show that an ac current enables the vortex matter in YBCO thin films to reorganize into two coexisting steady states of driven vortex motion with different characteristics. To study the transport current effects in YBCO thin films, we present a new empirical method to separate the total current distribution into a

  9. Finding the asymmetric parasitic source and drain resistances from the a.c. conductances of a single MOS transistor

    NASA Astrophysics Data System (ADS)

    Raychaudhuri, A.; Deen, M. J.; King, M. I. H.; Kolk, J.

    1996-06-01

    Layout asymmetry, processing, or hot-carrier stressing can give rise to unequal source and drain parasitic resistances in a MOSFET. In these cases, it is necessary to extract these resistances separately without the aid of other transistors. In this paper, we present a simple method to extract the source and drain parasitic resistances separately. This method, unlike earlier ones that depend on the measurements of the d.c. resistances of several MOSFETs, is based on accurate formulations and measurements of the a.c. conductances with respect to the gate and drain terminals of a single transistor. This allows us to get reasonably accurate estimates of these resistances in a more straightforward manner. We also discuss the main error terms in detail.

  10. Hypertonic-induced lamin A/C synthesis and distribution to nucleoplasmic speckles is mediated by TonEBP/NFAT5 transcriptional activator

    SciTech Connect

    Favale, Nicolas O.; Sterin Speziale, Norma B.; Fernandez Tome, Maria C.

    2007-12-21

    Lamin A/C is the most studied nucleoskeletal constituent. Lamin A/C expression indicates cell differentiation and is also a structural component of nuclear speckles, which are involved in gene expression regulation. Hypertonicity has been reported to induce renal epithelial cell differentiation and expression of TonEBP (NFAT5), a transcriptional activator of hypertonicity-induced gene transcription. In this paper, we investigate the effect of hypertonicity on lamin A/C expression in MDCK cells and the involvement of TonEBP. Hypertonicity increased lamin A/C expression and its distribution to nucleoplasm with speckled pattern. Microscopy showed codistribution of TonEBP and lamin A/C in nucleoplasmic speckles, and immunoprecipitation demonstrated their interaction. TonEBP silencing caused lamin A/C redistribution from nucleoplasmic speckles to the nuclear rim, followed by lamin decrease, thus showing that hypertonicity induces lamin A/C speckles through a TonEBP-dependent mechanism. We suggest that lamin A/C speckles could serve TonEBP as scaffold thus favoring its role in hypertonicity.

  11. Computational determination of absorbed dose distributions from gamma ray sources

    NASA Astrophysics Data System (ADS)

    Zhou, Chuanyu; Inanc, Feyzi

    2001-04-01

    A biomedical procedure known as brachytherapy involves insertion of many radioactive seeds into a sick gland for eliminating sick tissue. For such implementations, the spatial distribution of absorbed dose is very important. A simulation tool has been developed to determine the spatial distribution of absorbed dose in heterogeneous environments where the gamma ray source consists of many small internal radiation emitters. The computation is base on integral transport method and the computations are done in a parallel fashion. Preliminary results involving 137Cs and 125I sources surrounded by water and comparison of the results to the experimental and computational data available in the literature are presented.

  12. The brightness and spatial distributions of terrestrial radio sources

    NASA Astrophysics Data System (ADS)

    Offringa, A. R.; de Bruyn, A. G.; Zaroubi, S.; Koopmans, L. V. E.; Wijnholds, S. J.; Abdalla, F. B.; Brouw, W. N.; Ciardi, B.; Iliev, I. T.; Harker, G. J. A.; Mellema, G.; Bernardi, G.; Zarka, P.; Ghosh, A.; Alexov, A.; Anderson, J.; Asgekar, A.; Avruch, I. M.; Beck, R.; Bell, M. E.; Bell, M. R.; Bentum, M. J.; Best, P.; Bîrzan, L.; Breitling, F.; Broderick, J.; Brüggen, M.; Butcher, H. R.; de Gasperin, F.; de Geus, E.; de Vos, M.; Duscha, S.; Eislöffel, J.; Fallows, R. A.; Ferrari, C.; Frieswijk, W.; Garrett, M. A.; Grießmeier, J.; Hassall, T. E.; Horneffer, A.; Iacobelli, M.; Juette, E.; Karastergiou, A.; Klijn, W.; Kondratiev, V. I.; Kuniyoshi, M.; Kuper, G.; van Leeuwen, J.; Loose, M.; Maat, P.; Macario, G.; Mann, G.; McKean, J. P.; Meulman, H.; Norden, M. J.; Orru, E.; Paas, H.; Pandey-Pommier, M.; Pizzo, R.; Polatidis, A. G.; Rafferty, D.; Reich, W.; van Nieuwpoort, R.; Röttgering, H.; Scaife, A. M. M.; Sluman, J.; Smirnov, O.; Sobey, C.; Tagger, M.; Tang, Y.; Tasse, C.; Veen, S. ter; Toribio, C.; Vermeulen, R.; Vocks, C.; van Weeren, R. J.; Wise, M. W.; Wucknitz, O.

    2013-10-01

    Faint undetected sources of radio-frequency interference (RFI) might become visible in long radio observations when they are consistently present over time. Thereby, they might obstruct the detection of the weak astronomical signals of interest. This issue is especially important for Epoch of Reionization (EoR) projects that try to detect the faint redshifted H I signals from the time of the earliest structures in the Universe. We explore the RFI situation at 30-163 MHz by studying brightness histograms of visibility data observed with Low-Frequency Array (LOFAR), similar to radio-source-count analyses that are used in cosmology. An empirical RFI distribution model is derived that allows the simulation of RFI in radio observations. The brightness histograms show an RFI distribution that follows a power-law distribution with an estimated exponent around -1.5. With several assumptions, this can be explained with a uniform distribution of terrestrial radio sources whose radiation follows existing propagation models. Extrapolation of the power law implies that the current LOFAR EoR observations should be severely RFI limited if the strength of RFI sources remains strong after time integration. This is in contrast with actual observations, which almost reach the thermal noise and are thought not to be limited by RFI. Therefore, we conclude that it is unlikely that there are undetected RFI sources that will become visible in long observations. Consequently, there is no indication that RFI will prevent an EoR detection with LOFAR.

  13. Continuous-variable quantum key distribution with Gaussian source noise

    SciTech Connect

    Shen Yujie; Peng Xiang; Yang Jian; Guo Hong

    2011-05-15

    Source noise affects the security of continuous-variable quantum key distribution (CV QKD) and is difficult to analyze. We propose a model to characterize Gaussian source noise through introducing a neutral party (Fred) who induces the noise with a general unitary transformation. Without knowing Fred's exact state, we derive the security bounds for both reverse and direct reconciliations and show that the bound for reverse reconciliation is tight.

  14. Electric Transport Traction Power Supply System With Distributed Energy Sources

    NASA Astrophysics Data System (ADS)

    Abramov, E. Y.; Schurov, N. I.; Rozhkova, M. V.

    2016-04-01

    The paper states the problem of traction substation (TSS) leveling of daily-load curve for urban electric transport. The circuit of traction power supply system (TPSS) with distributed autonomous energy source (AES) based on photovoltaic (PV) and energy storage (ES) units is submitted here. The distribution algorithm of power flow for the daily traction load curve leveling is also introduced in this paper. In addition, it illustrates the implemented experiment model of power supply system.

  15. Distributed source x-ray tube technology for tomosynthesis imaging

    PubMed Central

    Sprenger, F.; Calderon-Colon, X.; Cheng, Y.; Englestad, K.; Lu, J.; Maltz, J.; Paidi, A.; Qian, X.; Spronk, D.; Sultana, S.; Yang, G.; Zhou, O.

    2011-01-01

    Tomosynthesis imaging requires projection images from different viewing angles. Conventional systems use a moving xray source to acquire the individual projections. Using a stationary distributed x-ray source with a number of sources that equals the number of required projections, this can be achieved without any mechanical motion. Advantages are a potentially faster image acquisition speed, higher spatial and temporal resolution and simple system design. We present distributed x-ray sources based on carbon nanotube (CNT) field emission cathodes. The field emission cathodes deliver the electrons required for x-ray production. CNT emitters feature a stable emission at high current density, a cold emission, excellent temporal control of the emitted electrons and good configurability. We discuss the use of stationary sources for two applications: (i) a linear tube for stationary digital breast tomosynthesis (sDBT), and (ii) a square tube for on-board tomosynthesis image-guided radiation therapy (IGRT). Results from high energy distributed sources up to 160kVp are also presented. PMID:21785671

  16. Method for image reconstruction of moving radionuclide source distribution

    DOEpatents

    Stolin, Alexander V.; McKisson, John E.; Lee, Seung Joon; Smith, Mark Frederick

    2012-12-18

    A method for image reconstruction of moving radionuclide distributions. Its particular embodiment is for single photon emission computed tomography (SPECT) imaging of awake animals, though its techniques are general enough to be applied to other moving radionuclide distributions as well. The invention eliminates motion and blurring artifacts for image reconstructions of moving source distributions. This opens new avenues in the area of small animal brain imaging with radiotracers, which can now be performed without the perturbing influences of anesthesia or physical restraint on the biological system.

  17. Production, Distribution, and Applications of Californium-252 Neutron Sources

    SciTech Connect

    Balo, P.A.; Knauer, J.B.; Martin, R.C.

    1999-10-03

    The radioisotope {sup 252}Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6-year half-life. A source the size of a person's little finger can emit up to 10{sup 11} neutrons/s. Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement, and minerals, as well as for detection and identification of explosives, laud mines, and unexploded military ordnance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards, and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 years of experience and by U.S. Bureau of Mines tests of source survivability during explosions. The production and distribution center for the U. S Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory (ORNL). DOE sells The radioisotope {sup 252}Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6- year half-life. A source the size of a person's little finger can emit up to 10 neutrons/s. Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement, and minerals, as well as for detection and identification of explosives, laud mines, and unexploded military ordnance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards, and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 years of experience and by U.S. Bureau of Mines tests of source survivability during explosions. The production and distribution center for the U. S Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory(ORNL). DOE sells {sup 252}Cf to commercial

  18. Security of quantum key distribution with light sources that are not independently and identically distributed

    NASA Astrophysics Data System (ADS)

    Nagamatsu, Yuichi; Mizutani, Akihiro; Ikuta, Rikizo; Yamamoto, Takashi; Imoto, Nobuyuki; Tamaki, Kiyoshi

    2016-04-01

    Although quantum key distribution (QKD) is theoretically secure, there is a gap between the theory and practice. In fact, real-life QKD may not be secure because component devices in QKD systems may deviate from the theoretical models assumed in security proofs. To solve this problem, it is necessary to construct the security proof under realistic assumptions on the source and measurement unit. In this paper, we prove the security of a QKD protocol under practical assumptions on the source that accommodate fluctuation of the phase and intensity modulations. As long as our assumptions hold, it does not matter at all how the phase and intensity distribute or whether or not their distributions over different pulses are independently and identically distributed. Our work shows that practical sources can be safely employed in QKD experiments.

  19. Production, distribution and applications of californium-252 neutron sources.

    PubMed

    Martin, R C; Knauer, J B; Balo, P A

    2000-01-01

    The radioisotope 252Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6-yr half-life. A source the size of a person's little finger can emit up to 10(11) neutrons s(-1). Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement and minerals, as well as for detection and identification of explosives, land mines and unexploded military ordinance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 yr of experience and by US Bureau of Mines tests of source survivability during explosions. The production and distribution center for the US Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory (ORNL). DOE sells 252Cf to commercial reencapsulators domestically and internationally. Sealed 252Cf sources are also available for loan to agencies and subcontractors of the US government and to universities for educational, research and medical applications. The REDC has established the Californium User Facility (CUF) for Neutron Science to make its large inventory of 252Cf sources available to researchers for irradiations inside uncontaminated hot cells. Experiments at the CUF include a land mine detection system, neutron damage testing of solid-state detectors, irradiation of human cancer cells for boron neutron capture therapy experiments and irradiation of rice to induce genetic mutations. PMID:11003521

  20. Oil source bed distribution in upper Tertiary of Gulf Coast

    SciTech Connect

    Dow, W.G.

    1985-02-01

    Effective oil source beds have not been reported in Miocene and younger Gulf Coast sediments and the organic matter present is invariably immature and oxidized. Crude oil composition, however, indicates origin from mature source beds containing reduced kerogen. Oil distribution suggests extensive vertical migration through fracture systems from localized sources in deeply buried, geopressured shales. A model is proposed in which oil source beds were deposited in intraslope basins that formed behind salt ridges. The combination of silled basin topography, rapid sedimentation, and enhanced oxygen-minimum zones during global warmups resulted in periodic anoxic environments and preservation of oil-generating organic matter. Anoxia was most widespread during the middle Miocene and Pliocene transgressions and rare during regressive cycles when anoxia occurred primarily in hypersaline conditions such as exist today in the Orca basin.

  1. Secure quantum key distribution with an uncharacterized source.

    PubMed

    Koashi, Masato; Preskill, John

    2003-02-01

    We prove the security of the Bennett-Brassard (BB84) quantum key distribution protocol for an arbitrary source whose averaged states are basis independent, a condition that is automatically satisfied if the source is suitably designed. The proof is based on the observation that, to an adversary, the key extraction process is equivalent to a measurement in the sigma(x) basis performed on a pure sigma(z)-basis eigenstate. The dependence of the achievable key length on the bit error rate is the same as that established by Shor and Preskill [Phys. Rev. Lett. 85, 441 (2000)

  2. Method and apparatus for reducing the harmonic currents in alternating-current distribution networks

    DOEpatents

    Beverly, L.H.; Hance, R.D.; Kristalinski, A.L.; Visser, A.T.

    1996-11-19

    An improved apparatus and method reduce the harmonic content of AC line and neutral line currents in polyphase AC source distribution networks. The apparatus and method employ a polyphase Zig-Zag transformer connected between the AC source distribution network and a load. The apparatus and method also employs a mechanism for increasing the source neutral impedance of the AC source distribution network. This mechanism can consist of a choke installed in the neutral line between the AC source and the Zig-Zag transformer. 23 figs.

  3. Method and apparatus for reducing the harmonic currents in alternating-current distribution networks

    DOEpatents

    Beverly, Leon H.; Hance, Richard D.; Kristalinski, Alexandr L.; Visser, Age T.

    1996-01-01

    An improved apparatus and method reduce the harmonic content of AC line and neutral line currents in polyphase AC source distribution networks. The apparatus and method employ a polyphase Zig-Zag transformer connected between the AC source distribution network and a load. The apparatus and method also employs a mechanism for increasing the source neutral impedance of the AC source distribution network. This mechanism can consist of a choke installed in the neutral line between the AC source and the Zig-Zag transformer.

  4. Review: Particle number size distributions from seven major sources and implications for source apportionment studies

    NASA Astrophysics Data System (ADS)

    Vu, Tuan V.; Delgado-Saborit, Juana Maria; Harrison, Roy M.

    2015-12-01

    The particle number size distribution (PNSD) of airborne particles not only provides us with information about sources and atmospheric processing of particles, but also plays an important role in determining regional lung dose. As a result, urban particles and their size distributions have received much attention with a rapid increase of publications in recent years. The object of this review is to synthesise and analyse existing knowledge on particles in urban environments with a focus on their number concentration and size distribution. This study briefly reviews the characterization of PNSD from seven major sources of urban particles including traffic emissions, industrial emissions, biomass burning, cooking, transported aerosol, marine aerosol and nucleation. It then discusses atmospheric physical processes such as coagulation or condensation which have a strong influence on PNSD. Finally, the implications of PNSD datasets for source modelling are briefly discussed. Based on this review, it is concluded that the concentrations, modal structures and temporal patterns of urban particles are strongly influenced by traffic emissions, which are identified as the main source of particle number in urban environments. Information derived from particle number size distributions is beginning to play an important role in source apportionment studies.

  5. Distributed policy based access to networked heterogeneous ISR data sources

    NASA Astrophysics Data System (ADS)

    Bent, G.; Vyvyan, D.; Wood, David; Zerfos, Petros; Calo, Seraphin

    2010-04-01

    Within a coalition environment, ad hoc Communities of Interest (CoI's) come together, perhaps for only a short time, with different sensors, sensor platforms, data fusion elements, and networks to conduct a task (or set of tasks) with different coalition members taking different roles. In such a coalition, each organization will have its own inherent restrictions on how it will interact with the others. These are usually stated as a set of policies, including security and privacy policies. The capability that we want to enable for a coalition operation is to provide access to information from any coalition partner in conformance with the policies of all. One of the challenges in supporting such ad-hoc coalition operations is that of providing efficient access to distributed sources of data, where the applications requiring the data do not have knowledge of the location of the data within the network. To address this challenge the International Technology Alliance (ITA) program has been developing the concept of a Dynamic Distributed Federated Database (DDFD), also know as a Gaian Database. This type of database provides a means for accessing data across a network of distributed heterogeneous data sources where access to the information is controlled by a mixture of local and global policies. We describe how a network of disparate ISR elements can be expressed as a DDFD and how this approach enables sensor and other information sources to be discovered autonomously or semi-autonomously and/or combined, fused formally defined local and global policies.

  6. Spatiotemporal distributions of tsunami sources and discovered periodicities

    NASA Astrophysics Data System (ADS)

    Levin, B. W.; Sasorova, E. V.

    2014-09-01

    Both spatial and spatiotemporal distributions of the sources of tsunamigenic earthquakes of tectonic origin over the last 112 years have been analyzed. This analysis has been made using tsunami databases published by the Institute of Computational Mathematics and Mathematical Geophysics (Siberian Branch, Russian Academy of Sciences) and the National Aeronautics and Space Administration (United States), as well as earthquake catalogs published by the National Earthquake Information Center (United States). It has been found that the pronounced activation of seismic processes and an increase in the total energy of tsunamigenic earthquakes were observed at the beginning of both the 20th (1905-1920) and 21st (2004-2011) centuries. Studying the spatiotemporal periodicity of such events on the basis of an analysis of the two-dimensional distributions of the sources of tectonic tsunamis has made it possible to determine localized latitudinal zones with a total lack of such events (90°-75° N, 45°-90° S, and 35°-25° N) and regions with a periodic occurrence of tsunamis mainly within the middle (65°-35° N and 25°-40° S) and subequatorial (15° N-20° S) latitudes of the Northern and Southern hemispheres. The objective of this work is to analyze the spatiotemporal distributions of sources of tsunamigenic earthquakes and the effect of the periodic occurrence of such events on the basis of data taken from global tsunami catalogs.

  7. Robust video transmission with distributed source coded auxiliary channel.

    PubMed

    Wang, Jiajun; Majumdar, Abhik; Ramchandran, Kannan

    2009-12-01

    We propose a novel solution to the problem of robust, low-latency video transmission over lossy channels. Predictive video codecs, such as MPEG and H.26x, are very susceptible to prediction mismatch between encoder and decoder or "drift" when there are packet losses. These mismatches lead to a significant degradation in the decoded quality. To address this problem, we propose an auxiliary codec system that sends additional information alongside an MPEG or H.26x compressed video stream to correct for errors in decoded frames and mitigate drift. The proposed system is based on the principles of distributed source coding and uses the (possibly erroneous) MPEG/H.26x decoder reconstruction as side information at the auxiliary decoder. The distributed source coding framework depends upon knowing the statistical dependency (or correlation) between the source and the side information. We propose a recursive algorithm to analytically track the correlation between the original source frame and the erroneous MPEG/H.26x decoded frame. Finally, we propose a rate-distortion optimization scheme to allocate the rate used by the auxiliary encoder among the encoding blocks within a video frame. We implement the proposed system and present extensive simulation results that demonstrate significant gains in performance both visually and objectively (on the order of 2 dB in PSNR over forward error correction based solutions and 1.5 dB in PSNR over intrarefresh based solutions for typical scenarios) under tight latency constraints. PMID:19703801

  8. Atmospheric PAHs in North China: Spatial distribution and sources.

    PubMed

    Zhang, Yanjun; Lin, Yan; Cai, Jing; Liu, Yue; Hong, Linan; Qin, Momei; Zhao, Yifan; Ma, Jin; Wang, Xuesong; Zhu, Tong; Qiu, Xinghua; Zheng, Mei

    2016-09-15

    Polycyclic aromatic hydrocarbons (PAHs), formed through incomplete combustion process, have adverse health effects. To investigate spatial distribution and sources of PAHs in North China, PAHs with passive sampling in 90 gridded sites during June to September in 2011 were analyzed. The average concentration of the sum of fifteen PAHs in North China is 220±14ng/m(3), with the highest in Shanxi, followed by Shandong and Hebei, and then the Beijing-Tianjin area. Major sources of PAHs are identified for each region of North China, coke process for Shanxi, biomass burning for Hebei and Shandong, and coal combustion for Beijing-Tianjin area, respectively. Emission inventory is combined with back trajectory analysis to study the influence of emissions from surrounding areas at receptor sites. Shanxi and Beijing-Tianjin areas are more influenced by sources nearby while regional sources have more impact on Hebei and Shandong areas. Results from this study suggest the areas where local emission should be the major target for control and areas where both local and regional sources should be considered for PAH abatement in North China. PMID:27241206

  9. CMP reflection imaging via interferometry of distributed subsurface sources

    NASA Astrophysics Data System (ADS)

    Kim, D.; Brown, L. D.; Quiros, D. A.

    2015-12-01

    The theoretical foundations of recovering body wave energy via seismic interferometry are well established. However in practice, such recovery remains problematic. Here, synthetic seismograms computed for subsurface sources are used to evaluate the geometrical combinations of realistic ambient source and receiver distributions that result in useful recovery of virtual body waves. This study illustrates how surface receiver arrays that span a limited distribution suite of sources, can be processed to reproduce virtual shot gathers that result in CMP gathers which can be effectively stacked with traditional normal moveout corrections. To verify the feasibility of the approach in practice, seismic recordings of 50 aftershocks following the magnitude of 5.8 Virginia earthquake occurred in August, 2011 have been processed using seismic interferometry to produce seismic reflection images of the crustal structure above and beneath the aftershock cluster. Although monotonic noise proved to be problematic by significantly reducing the number of usable recordings, the edited dataset resulted in stacked seismic sections characterized by coherent reflections that resemble those seen on a nearby conventional reflection survey. In particular, "virtual" reflections at travel times of 3 to 4 seconds suggest reflector sat approximately 7 to 12 km depth that would seem to correspond to imbricate thrust structures formed during the Appalachian orogeny. The approach described here represents a promising new means of body wave imaging of 3D structure that can be applied to a wide array of geologic and energy problems. Unlike other imaging techniques using natural sources, this technique does not require precise source locations or times. It can thus exploit aftershocks too small for conventional analyses. This method can be applied to any type of microseismic cloud, whether tectonic, volcanic or man-made.

  10. Mapping the source distribution of microseisms using noise covariogram envelopes

    NASA Astrophysics Data System (ADS)

    Sadeghisorkhani, Hamzeh; Gudmundsson, Ólafur; Roberts, Roland; Tryggvason, Ari

    2016-06-01

    We introduce a method for mapping the noise-source distribution of microseisms which uses information from the full length of covariograms (cross-correlations). We derive a forward calculation based on the plane-wave assumption in 2-D, to formulate an iterative, linearized inversion of covariogram envelopes in the time domain. The forward calculation involves bandpass filtering of the covariograms. The inversion exploits the well-known feature of noise cross-correlation, that is, an anomaly in the noise field that is oblique to the interstation direction appears as cross-correlation amplitude at a smaller time lag than the in-line, surface wave arrival. Therefore, the inversion extracts more information from the covariograms than that contained at the expected surface wave arrival, and this allows us to work with few stations to find the propagation directions of incoming energy. The inversion is naturally applied to data that retain physical units that are not amplitude normalized in any way. By dividing a network into groups of stations, we can constrain the source location by triangulation. We demonstrate results of the method with synthetic data and one year (2012) of data from the Swedish National Seismic Network and also look at the seasonal variation of source distribution around Scandinavia. After preprocessing and cross-correlation, the stations are divided into five groups of 9-12 stations. We invert the envelopes of each group in eight period ranges between 2 and 25 s. Results show that the noise sources at short periods (less than 12 s) lie predominantly in the North Atlantic Ocean and the Barents Sea, and at longer periods the energy appears to have a broader distribution. The strongly anisotropic source distribution in this area is estimated to cause significant biases of velocity measurements compared to the level of heterogeneity in the region. The amplitude of the primary microseisms varies little over the year, but secondary microseisms are much

  11. Mapping the source distribution of microseisms using noise covariogram envelopes

    NASA Astrophysics Data System (ADS)

    Sadeghisorkhani, Hamzeh; Gudmundsson, Ólafur; Roberts, Roland; Tryggvason, Ari

    2016-03-01

    We introduce a method for mapping the noise-source distribution of microseisms which uses information from the full length of covariograms (cross-correlations). We derive a forward calculation based on the plane-wave assumption in 2D, to formulate an iterative, linearized inversion of covariogram envelopes in the time domain. The forward calculation involves bandpass filtering of the covariograms. The inversion exploits the well-known feature of noise cross-correlation, i.e., that an anomaly in the noise field that is oblique to the inter-station direction appears as cross-correlation amplitude at a smaller time lag than the in-line, surface-wave arrival. Therefore, the inversion extracts more information from the covariograms than that contained at the expected surface-wave arrival, and this allows us to work with few stations to find the propagation directions of incoming energy. The inversion is naturally applied to data that retain physical units, i.e., that are not amplitude normalized in any way. By dividing a network into groups of stations, we can constrain the source location by triangulation. We demonstrate results of the method with synthetic data and one year (2012) of data from the Swedish National Seismic Network (SNSN) and also look at the seasonal variation of source distribution around Scandinavia. After preprocessing and cross-correlation, the stations are divided into 5 groups of 9 to 12 stations. We invert the envelopes of each group in 8 period ranges between 2 to 25 sec. Results show that the noise sources at short periods (less than 12 sec) lie predominantly in the North Atlantic Ocean and the Barents Sea, and at longer periods the energy appears to have a broader distribution. The strongly anisotropic source distribution in this area is estimated to cause significant biases of velocity measurements compared to the level of heterogeneity in the region. The amplitude of the primary microseisms varies little over the year, but secondary

  12. Extending Marine Species Distribution Maps Using Non-Traditional Sources

    PubMed Central

    Moretzsohn, Fabio; Gibeaut, James

    2015-01-01

    Abstract Background Traditional sources of species occurrence data such as peer-reviewed journal articles and museum-curated collections are included in species databases after rigorous review by species experts and evaluators. The distribution maps created in this process are an important component of species survival evaluations, and are used to adapt, extend and sometimes contract polygons used in the distribution mapping process. New information During an IUCN Red List Gulf of Mexico Fishes Assessment Workshop held at The Harte Research Institute for Gulf of Mexico Studies, a session included an open discussion on the topic of including other sources of species occurrence data. During the last decade, advances in portable electronic devices and applications enable 'citizen scientists' to record images, location and data about species sightings, and submit that data to larger species databases. These applications typically generate point data. Attendees of the workshop expressed an interest in how that data could be incorporated into existing datasets, how best to ascertain the quality and value of that data, and what other alternate data sources are available. This paper addresses those issues, and provides recommendations to ensure quality data use. PMID:25941453

  13. Diversity, distribution and sources of bacteria in residential kitchens.

    PubMed

    Flores, Gilberto E; Bates, Scott T; Caporaso, J Gregory; Lauber, Christian L; Leff, Jonathan W; Knight, Rob; Fierer, Noah

    2013-02-01

    Bacteria readily colonize kitchen surfaces, and the exchange of microbes between humans and the kitchen environment can impact human health. However, we have a limited understanding of the overall diversity of these communities, how they differ across surfaces and sources of bacteria to kitchen surfaces. Here we used high-throughput sequencing of the 16S rRNA gene to explore biogeographical patterns of bacteria across > 80 surfaces within the kitchens of each of four households. In total, 34 bacterial and two archaeal phyla were identified, with most sequences belonging to the Actinobacteria, Bacteroidetes, Firmicutes and Proteobacteria. Genera known to contain common food-borne pathogens were low in abundance but broadly distributed throughout the kitchens, with different taxa exhibiting distinct distribution patterns. The most diverse communities were associated with infrequently cleaned surfaces such as fans above stoves, refrigerator/freezer door seals and floors. In contrast, the least diverse communities were observed in and around sinks, which were dominated by biofilm-forming Gram-negative lineages. Community composition was influenced by conditions on individual surfaces, usage patterns and dispersal from source environments. Human skin was the primary source of bacteria across all kitchen surfaces, with contributions from food and faucet water dominating in a few specific locations. This study demonstrates that diverse bacterial communities are widely distributed in residential kitchens and that the composition of these communities is often predictable. These results also illustrate the ease with which human- and food-associated bacteria can be transferred in residential settings to kitchen surfaces. PMID:23171378

  14. Streamlined Genome Sequence Compression using Distributed Source Coding

    PubMed Central

    Wang, Shuang; Jiang, Xiaoqian; Chen, Feng; Cui, Lijuan; Cheng, Samuel

    2014-01-01

    We aim at developing a streamlined genome sequence compression algorithm to support alternative miniaturized sequencing devices, which have limited communication, storage, and computation power. Existing techniques that require heavy client (encoder side) cannot be applied. To tackle this challenge, we carefully examined distributed source coding theory and developed a customized reference-based genome compression protocol to meet the low-complexity need at the client side. Based on the variation between source and reference, our protocol will pick adaptively either syndrome coding or hash coding to compress subsequences of changing code length. Our experimental results showed promising performance of the proposed method when compared with the state-of-the-art algorithm (GRS). PMID:25520552

  15. Sources and distribution of hexabromocyclododecanes (HBCDs) in Japanese river sediment.

    PubMed

    Managaki, Satoshi; Enomoto, Iku; Masunaga, Shigeki

    2012-03-01

    The distribution of hexabromocyclododecane (HBCD) in the sediment of three Japanese rivers with different characteristics (i.e., population and potential source in the catchment) was investigated and compared with the results estimated using a multimedia fate model (ChemCAN). High concentrations of HBCD in sediments in the range of 134-2060 ng g(-1) were found in a river receiving textile wastewater. This contrasted with the much lower concentrations (0.8-4.8 ng g(-1)) observed for an urban river (with a surrounding population of 1.8 million). The medians of observed HBCD concentrations in each river were close to those estimated based on the assumed input source (e.g., 1810 ng g(-1) for the observed median concentration, and 1436 ng g(-1) for the estimation, in the Kuzuryu River). These results demonstrated the importance of considering source contributions of HBCD, including both industrial and consumer sources, to aquatic environments, for reliable risk management. PMID:22286550

  16. Considering sources and detectors distributions for quantitative photoacoustic tomography

    PubMed Central

    Song, Ningning; Deumié, Carole; Da Silva, Anabela

    2014-01-01

    Photoacoustic tomography (PAT) is a hybrid imaging modality that takes advantage of high optical contrast brought by optical imaging and high spatial resolution brought by ultrasound imaging. However, the quantification in photoacoustic imaging is challenging. Multiple optical illumination approach has proven to achieve uncoupling of diffusion and absorption effects. In this paper, this protocol is adopted and synthetic photoacoustic data, blurred with some noise, were generated. The influence of the distribution of optical sources and transducers on the reconstruction of the absorption and diffusion coefficients maps is studied. Specific situations with limited view angles were examined. The results show multiple illuminations with a wide field improve the reconstructions. PMID:25426322

  17. Size distributions, sources and source areas of water-soluble organic carbon in urban background air

    NASA Astrophysics Data System (ADS)

    Timonen, H.; Saarikoski, S.; Tolonen-Kivimäki, O.; Aurela, M.; Saarnio, K.; Petäjä, T.; Aalto, P. P.; Kulmala, M.; Pakkanen, T.; Hillamo, R.

    2008-04-01

    This paper represents the results of one year long measurement period of the size distributions of water-soluble organic carbon (WSOC), inorganic ions and gravimetric mass of particulate matter. Measurements were done at an urban background station (SMEAR III) by using a micro-orifice uniform deposit impactor (MOUDI). The site is located in northern European boreal region in Helsinki, Finland. The WSOC size distribution measurements were completed with the chemical analysis of inorganic ions, organic carbon (OC) and monosaccharide anhydrides from the filter samples. During the measurements gravimetric mass in the MOUDI collections varied between 3.4 and 55.0 μg m-3 and the WSOC concentration was between 0.3 and 7.4 μg m-3. On average, water-soluble particulate organic matter (WSPOM, WSOC multiplied by 1.6) comprised 25±7.7% and 7.5±3.4% of aerosol PM1 mass and the PM1-10 mass, respectively. Inorganic ions contributed 33±12% and 28±19% of the analyzed PM1 and PM1-10 aerosol mass. Five different aerosol categories corresponding to different sources or source areas were identified (long-range transport aerosols, biomass burning aerosols from wild land fires and from small-scale wood combustion, aerosols originating from marine areas and from the clean arctic areas). Clear differences in WSOC concentrations and size distributions originating from different sources or source areas were observed, although there are also many other factors which might affect the results. E.g. the local conditions and sources of volatile organic compounds (VOCs) and aerosols as well as various transformation processes are likely to have an impact on the measured aerosol composition. Using the source categories, it was identified that especially the oxidation products of biogenic VOCs in summer had a clear effect on WSOC concentrations.

  18. Local tsunamis and distributed slip at the source

    USGS Publications Warehouse

    Geist, E.L.; Dmowska, R.

    1999-01-01

    Variations in the local tsunami wave field are examined in relation to heterogeneous slip distributions that are characteristic of many shallow subduction zone earthquakes. Assumptions inherent in calculating the coseismic vertical displacement field that defines the initial condition for tsunami propagation are examined. By comparing the seafloor displacement from uniform slip to that from an ideal static crack, we demonstrate that dip-directed slip variations significantly affect the initial cross-sectional wave profile. Because of the hydrodynamic stability of tsunami wave forms, these effects directly impact estimates of maximum runup from the local tsunami. In most cases, an assumption of uniform slip in the dip direction significantly underestimates the maximum amplitude and leading wave steepness of the local tsunami. Whereas dip-directed slip variations affect the initial wave profile, strike-directed slip variations result in wavefront-parallel changes in amplitude that are largely preserved during propagation from the source region toward shore, owing to the effects of refraction. Tests of discretizing slip distributions indicate that small fault surface elements of dimensions similar to the source depth can acceptably approximate the vertical displacement field in comparison to continuous slip distributions. Crack models for tsunamis generated by shallow subduction zone earthquakes indicate that a rupture intersecting the free surface results in approximately twice the average slip. Therefore, the observation of higher slip associated with tsunami earthquakes relative to typical subduction zone earthquakes of the same magnitude suggests that tsunami earthquakes involve rupture of the seafloor, whereas rupture of deeper subduction zone earthquakes may be imbedded and not reach the seafloor.

  19. Reservoir, seal, and source rock distribution in Essaouira Rift Basin

    SciTech Connect

    Ait Salem, A. )

    1994-07-01

    The Essaouira onshore basin is an important hydrocarbon generating basin, which is situated in western Morocco. There are seven oil and gas-with-condensate fields; six are from Jurassic reservoirs and one from a Triassic reservoir. As a segment of the Atlantic passive continental margin, the Essaouira basin was subjected to several post-Hercynian basin deformation phases, which resulted in distribution, in space and time, of reservoir, seal, and source rock. These basin deformations are synsedimentary infilling of major half grabens with continental red buds and evaporite associated with the rifting phase, emplacement of a thick postrifting Jurassic and Cretaceous sedimentary wedge during thermal subsidence, salt movements, and structural deformations in relation to the Atlas mergence. The widely extending lower Oxfordian shales are the only Jurassic shale beds penetrated and recognized as potential and mature source rocks. However, facies analysis and mapping suggested the presence of untested source rocks in Dogger marine shales and Triassic to Liassic lacustrine shales. Rocks with adequate reservoir characteristics were encountered in Triassic/Liassic fluvial sands, upper Liassic dolomites, and upper Oxfordian sandy dolomites. The seals are provided by Liassic salt for the lower reservoirs and Middle to Upper Jurassic anhydrite for the upper reservoirs. Recent exploration studies demonstrate that many prospective structure reserves remain untested.

  20. Energy efficient wireless sensor networks using asymmetric distributed source coding

    NASA Astrophysics Data System (ADS)

    Rao, Abhishek; Kulkarni, Murlidhar

    2013-01-01

    Wireless Sensor Networks (WSNs) are networks of sensor nodes deployed over a geographical area to perform a specific task. WSNs pose many design challenges. Energy conservation is one such design issue. In literature a wide range of solutions addressing this issue have been proposed. Generally WSNs are densely deployed. Thus the nodes with the close proximity are more likely to have the same data. Transmission of such non-aggregated data may lead to an inefficient energy management. Hence the data fusion has to be performed at the nodes so as to combine the edundant information into a single data unit. Distributed Source Coding is an efficient approach in achieving this task. In this paper an attempt has been made in modeling such a system. Various energy efficient codes were considered for the analysis. System performance in terms of energy efficiency has been made.

  1. Pressure distribution in unsteady sink and source flows.

    PubMed

    Voropayev, S I

    2015-05-01

    Basic flow generated in a viscous incompressible fluid by a "point" sink (source) of mass is revised. In practice, such flow can be modeled by sucking (pushing) fluid from a thin tube with a small porous sphere at one end. Intuitively, by sucking (pushing) fluid, one creates low (high) pressure near the origin and a positive (negative) radial pressure gradient drives the fluid to (from) the origin. A simple analysis, however, shows that the pressure distribution for both steady flows is the same. Then a question arises: How does the fluid "know" in what direction to flow? To explain this "paradox" an unsteady flow is considered and the pressure terms responsible for the flow direction are derived. PMID:26066255

  2. Reference-frame-independent quantum key distribution with source flaws

    NASA Astrophysics Data System (ADS)

    Wang, Can; Sun, Shi-Hai; Ma, Xiang-Chun; Tang, Guang-Zhao; Liang, Lin-Mei

    2015-10-01

    Compared with the traditional protocols of quantum key distribution (QKD), the reference-frame-independent (RFI)-QKD protocol has been generally proved to be very useful and practical, since its experimental implementation can be simplified without the alignment of a reference frame. In most RFI-QKD systems, the encoding states are always taken to be perfect, which, however, is not practical in realizations. In this paper, we consider the security of RFI QKD with source flaws based on the loss-tolerant method proposed by Tamaki et al. [Phys. Rev. A 90, 052314 (2014), 10.1103/PhysRevA.90.052314]. As the six-state protocol can be realized with four states, we show that the RFI-QKD protocol can also be performed with only four encoding states instead of six encoding states in its standard version. Furthermore, the numerical simulation results show that the source flaws in the key-generation basis (Z basis) will reduce the key rate but are loss tolerant, while the ones in X and Y bases almost have no effect and the key rate remains almost the same even when they are very large. Hence, our method and results will have important significance in practical experiments, especially in earth-to-satellite or chip-to-chip quantum communications.

  3. Size distributions, sources and source areas of water-soluble organic carbon in urban background air

    NASA Astrophysics Data System (ADS)

    Timonen, H.; Saarikoski, S.; Tolonen-Kivimäki, O.; Aurela, M.; Saarnio, K.; Petäjä, T.; Aalto, P. P.; Kulmala, M.; Pakkanen, T.; Hillamo, R.

    2008-09-01

    This paper represents the results of one year long measurement period of the size distributions of water-soluble organic carbon (WSOC), inorganic ions and gravimetric mass of particulate matter. Measurements were done at an urban background station (SMEAR III) by using a micro-orifice uniform deposit impactor (MOUDI). The site is located in northern European boreal region in Helsinki, Finland. The WSOC size distribution measurements were completed with the chemical analysis of inorganic ions, organic carbon (OC) and monosaccharide anhydrides from the filter samples (particle aerodynamic diameter smaller than 1 μm, PM1). Gravimetric mass concentration varied during the MOUDI samplings between 3.4 and 55.0 μg m-3 and the WSOC concentrations were between 0.3 and 7.4 μg m-3. On average, water-soluble particulate organic matter (WSPOM, WSOC multiplied by 1.6 to convert the analyzed carbon mass to organic matter mass) comprised 25±7.7% and 7.5±3.4% of aerosol PM1 mass and the PM1-10 mass, respectively. Inorganic ions contributed 33±12% and 28±19% of the analyzed PM1 and PM1-10 aerosol mass. Five different aerosol categories corresponding to different sources or source areas were identified (long-range transport aerosols, biomass burning aerosols from wild land fires and from small-scale wood combustion, aerosols originating from marine areas and from the clean arctic areas). Categories were identified mainly using levoglucosan concentration level for wood combustion and air mass backward trajectories for other groups. Clear differences in WSOC concentrations and size distributions originating from different sources or source areas were observed, although there are also many other factors which might affect the results. E.g. the local conditions and sources of volatile organic compounds (VOCs) and aerosols as well as various transformation processes are likely to have an impact on the measured aerosol composition. Using the source categories, it was identified that

  4. 78 FR 41398 - SourceGas Distribution LLC; Notice of Filing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-10

    ... Energy Regulatory Commission SourceGas Distribution LLC; Notice of Filing Take notice that on June 27, 2013, SourceGas Distribution LLC (SourceGas) filed a Rate Election and revised Statement of Operating... and 284.224). SourceGas proposes to revise its fuel reimbursement quantity percentage to reflect...

  5. Large-Scale Transport Model Uncertainty and Sensitivity Analysis: Distributed Sources in Complex, Hydrogeologic Systems

    NASA Astrophysics Data System (ADS)

    Wolfsberg, A.; Kang, Q.; Li, C.; Ruskauff, G.; Bhark, E.; Freeman, E.; Prothro, L.; Drellack, S.

    2007-12-01

    simulations are challenged by the distributed sources in each of the Corrective Action Units, by complex mass transfer processes, and by the size and complexity of the field- scale flow models. An efficient methodology utilizing particle tracking results and convolution integrals provides insitu concentrations appropriate for Monte Carlo analysis. Uncertainty in source releases and transport parameters including effective porosity, fracture apertures and spacing, matrix diffusion coefficients, sorption coefficients, and colloid load and mobility are considered. With the distributions of input uncertainties and output plume volumes, global analysis methods including stepwise regression, contingency table analysis, and classification tree analysis are used to develop sensitivity rankings of parameter uncertainties for each model considered, thus assisting a variety of decisions. The National Security Technologies, LLC component of this work is DOE/NV/25946--xxx and was done under contract number DE-AC52-O6NA25946 with the U.S. Department of Energy

  6. An Approach to Suppressing Both Shaft Voltage and Leakage Current in an AC Motor Driven by a Voltage-Source PWM Inverter

    NASA Astrophysics Data System (ADS)

    Doumoto, Takafumi; Akagi, Hirofumi

    This paper proposes a practical approach to suppressing both shaft voltage and leakage current in an ac motor driven by a voltage-source PWM inverter. This approach is characterized by using a neutral line of the ac motor. A common-mode inductor is connected between the inverter and the motor. Moreover, a resistor and a capacitor are connected in series between the motor neutral point and the inverter negative dc bus. This unique circuit configuration makes the common-mode inductor effective in reducing the common-mode voltage appearing at the motor terminals. As a result, both shaft voltage and ground current are significantly suppressed with low cost. Over-voltages at the end of a cable can be suppressed by a normal-mode inductor and a resistor which are connected in parallel. The validity and effectiveness of the new approach are verified by experimental results from a 5-kVA laboratory system.

  7. Distribution of astronomical sources in the second Equatorial Infrared Catalogue

    NASA Technical Reports Server (NTRS)

    Nagy, T. A.; Sweeney, L. H.; Lesh, J. R.; Mead, J. M.; Maran, S. P.; Heinsheimer, T. F.; Yates, F. F.

    1979-01-01

    Measurements of infrared (2.7-micron) source positions and flux densities have been derived based on an additional 60.6 hours of satellite observations beyond those considered in the preparation of the Equatorial Infrared Catalogue No. 1 (EIC-1). These data have been processed together with the EIC-1 data to produce EIC-2. The new catalog differs from EIC-1 as follows: there are 1278 sources; there is a larger percentage of unidentified sources; there are increased numbers of sources identified with Two-Micron Sky Survey sources, AFGL sources, AGK3 stars and SAO stars.

  8. 78 FR 56685 - SourceGas Distribution LLC; Notice of Application

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-13

    ... Energy Regulatory Commission SourceGas Distribution LLC; Notice of Application Take notice that on August 27, 2013, SourceGas Distribution LLC (SourceGas), 600 12th Street, Suite 300, Golden, Colorado 80401, filed in Docket No. CP13-540-000 an application pursuant to section 7(f) of the Natural Gas Act...

  9. 78 FR 6318 - SourceGas Distribution LLC; Notice of Petition for Rate Approval

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-30

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission SourceGas Distribution LLC; Notice of Petition for Rate Approval Take notice that on January 15, 2013, SourceGas Distribution LLC (SourceGas) filed a rate election pursuant...

  10. 77 FR 28374 - SourceGas Distribution LLC; Notice of Compliance Filing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-14

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission SourceGas Distribution LLC; Notice of Compliance Filing Take notice that on April 30, 2012, SourceGas Distribution LLC (SourceGas) filed a revised Statement of Operating...

  11. Chemotaxis Increases the Residence Time Distribution of Bacteria in Granular Media Containing Distributed Contaminant Sources

    NASA Astrophysics Data System (ADS)

    Adadevoh, J.; Triolo, S.; Ramsburg, C. A.; Ford, R.

    2015-12-01

    The use of chemotactic bacteria in bioremediation has the potential to increase access to, and biotransformation of, contaminant mass within the subsurface environment. This laboratory-scale study aimed to understand and quantify the influence of chemotaxis on residence times of pollutant-degrading bacteria within homogeneous treatment zones. Focus was placed on a continuous flow sand-packed column system in which a uniform distribution of naphthalene crystals created distributed sources of dissolved phase contaminant. A 10 mL pulse of Pseudomonas putida G7, which is chemotactic to naphthalene, and Pseudomonas putida G7 Y1, a non-chemotactic mutant strain, were simultaneously introduced into the sand-packed column at equal concentrations. Breakthrough curves obtained for the bacteria from column experiments conducted with and without naphthalene were used to quantify the effect of chemotaxis on transport parameters. In the presence of the chemoattractant, longitudinal dispersivity of PpG7 increased by a factor of 3 and percent recovery decreased from 21% to 12%. The results imply that pore-scale chemotaxis responses are evident at an interstitial fluid velocity of 1.7 m/d, which is within the range of typical groundwater flow. Within the context of bioremediation, chemotaxis may work to enhance bacterial residence times in zones of contamination thereby improving treatment.

  12. Development of a hardware-based AC microgrid for AC stability assessment

    NASA Astrophysics Data System (ADS)

    Swanson, Robert R.

    As more power electronic-based devices enable the development of high-bandwidth AC microgrids, the topic of microgrid power distribution stability has become of increased interest. Recently, researchers have proposed a relatively straightforward method to assess the stability of AC systems based upon the time-constants of sources, the net bus capacitance, and the rate limits of sources. In this research, a focus has been to develop a hardware test system to evaluate AC system stability. As a first step, a time domain model of a two converter microgrid was established in which a three phase inverter acts as a power source and an active rectifier serves as an adjustable constant power AC load. The constant power load can be utilized to create rapid power flow transients to the generating system. As a second step, the inverter and active rectifier were designed using a Smart Power Module IGBT for switching and an embedded microcontroller as a processor for algorithm implementation. The inverter and active rectifier were designed to operate simultaneously using a synchronization signal to ensure each respective local controller operates in a common reference frame. Finally, the physical system was created and initial testing performed to validate the hardware functionality as a variable amplitude and variable frequency AC system.

  13. WATER QUALITY IN SOURCE WATER, TREATMENT, AND DISTRIBUTION SYSTEMS

    EPA Science Inventory

    Most drinking water utilities practice the multiple-barrier concept as the guiding principle for providing safe water. This chapter discusses multiple barriers as they relate to the basic criteria for selecting and protecting source waters, including known and potential sources ...

  14. Finite-Element Model Predicts Current Density Distribution for Clinical Applications of tDCS and tACS.

    PubMed

    Neuling, Toralf; Wagner, Sven; Wolters, Carsten H; Zaehle, Tino; Herrmann, Christoph S

    2012-01-01

    Transcranial direct current stimulation (tDCS) has been applied in numerous scientific studies over the past decade. However, the possibility to apply tDCS in therapy of neuropsychiatric disorders is still debated. While transcranial magnetic stimulation (TMS) has been approved for treatment of major depression in the United States by the Food and Drug Administration (FDA), tDCS is not as widely accepted. One of the criticisms against tDCS is the lack of spatial specificity. Focality is limited by the electrode size (35 cm(2) are commonly used) and the bipolar arrangement. However, a current flow through the head directly from anode to cathode is an outdated view. Finite-element (FE) models have recently been used to predict the exact current flow during tDCS. These simulations have demonstrated that the current flow depends on tissue shape and conductivity. To face the challenge to predict the location, magnitude, and direction of the current flow induced by tDCS and transcranial alternating current stimulation (tACS), we used a refined realistic FE modeling approach. With respect to the literature on clinical tDCS and tACS, we analyzed two common setups for the location of the stimulation electrodes which target the frontal lobe and the occipital lobe, respectively. We compared lateral and medial electrode configuration with regard to their usability. We were able to demonstrate that the lateral configurations yielded more focused stimulation areas as well as higher current intensities in the target areas. The high resolution of our simulation allows one to combine the modeled current flow with the knowledge of neuronal orientation to predict the consequences of tDCS and tACS. Our results not only offer a basis for a deeper understanding of the stimulation sites currently in use for clinical applications but also offer a better interpretation of observed effects. PMID:23015792

  15. Use of open source distribution for a machine tool controller

    NASA Astrophysics Data System (ADS)

    Shackleford, William P.; Proctor, Frederick M.

    2001-02-01

    In recent years a growing number of government and university las, non-profit organizations and even a few for- profit corporations have found that making their source code public is good for both developers and users. In machine tool control, a growing number of users are demanding that the controllers they buy be `open architecture,' which would allow third parties and end-users at least limited ability to modify, extend or replace the components of that controller. This paper examines the advantages and dangers of going one step further, and providing `open source' controllers by relating the experiences of users and developers of the Enhanced Machine Controller. We also examine some implications for the development of standards for open-architecture but closed-source controllers. Some of the questions we hope to answer include: How can the quality be maintained after the source code has been modified? Can the code be trusted to run on expensive machines and parts, or when the safety of the operator is an issue? Can `open- architecture' but closed-source controllers ever achieve the level of flexibility or extensibility that open-source controllers can?

  16. Volatile Organic Compounds: Characteristics, distribution and sources in urban schools

    NASA Astrophysics Data System (ADS)

    Mishra, Nitika; Bartsch, Jennifer; Ayoko, Godwin A.; Salthammer, Tunga; Morawska, Lidia

    2015-04-01

    Long term exposure to organic pollutants, both inside and outside school buildings may affect children's health and influence their learning performance. Since children spend significant amount of time in school, air quality, especially in classrooms plays a key role in determining the health risks associated with exposure at schools. Within this context, the present study investigated the ambient concentrations of Volatile Organic Compounds (VOCs) in 25 primary schools in Brisbane with the aim to quantify the indoor and outdoor VOCs concentrations, identify VOCs sources and their contribution, and based on these; propose mitigation measures to reduce VOCs exposure in schools. One of the most important findings is the occurrence of indoor sources, indicated by the I/O ratio >1 in 19 schools. Principal Component Analysis with Varimax rotation was used to identify common sources of VOCs and source contribution was calculated using an Absolute Principal Component Scores technique. The result showed that outdoor 47% of VOCs were contributed by petrol vehicle exhaust but the overall cleaning products had the highest contribution of 41% indoors followed by air fresheners and art and craft activities. These findings point to the need for a range of basic precautions during the selection, use and storage of cleaning products and materials to reduce the risk from these sources.

  17. Acetone in the atmosphere: Distribution, sources, and sinks

    NASA Technical Reports Server (NTRS)

    Singh, H. B.; O'Hara, D.; Herlth, D.; Sachse, W.; Blake, D. R.; Bradshaw, J. D.; Kanakidou, M.; Crutzen, P. J.

    1994-01-01

    Acetone (CH3COCH3) was found to be the dominant nonmethane organic species present in the atmosphere sampled primarily over eastern Canada (0-6 km, 35 deg-65 deg N) during ABLE3B (July to August 1990). A concentration range of 357 to 2310 ppt (= 10(exp -12) v/v) with a mean value of 1140 +/- 413 ppt was measured. Under extremely clean conditions, generally involving Arctic flows, lowest (background) mixing ratios of 550 +/- 100 ppt were present in much of the troposphere studied. Correlations between atmospheric mixing ratios of acetone and select species such as C2H2, CO, C3H8, C2Cl4 and isoprene provided important clues to its possible sources and to the causes of its atmospheric variability. Biomass burning as a source of acetone has been identified for the first time. By using atmospheric data and three-dimensional photochemical models, a global acetone source of 40-60 Tg (= 10(exp 12) g)/yr is estimated to be present. Secondary formation from the atmospheric oxidation of precursor hydrocarbons (principally propane, isobutane, and isobutene) provides the single largest source (51%). The remainder is attributable to biomass burning (26%), direct biogenic emissions (21%), and primary anthropogenic emissions (3%). Atmospheric removal of acetone is estimated to be due to photolysis (64%), reaction with OH radicals (24%), and deposition (12%). Model calculations also suggest that acetone photolysis contributed significantly to PAN formation (100-200 ppt) in the middle and upper troposphere of the sampled region and may be important globally. While the source-sink equation appears to be roughly balanced, much more atmospheric and source data, especially from the southern hemisphere, are needed to reliably quantify the atmospheric budget of acetone.

  18. 77 FR 10490 - SourceGas Distribution LLC; Notice of Filing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-22

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission SourceGas Distribution LLC; Notice of Filing Take notice that on February 14, 2012, SourceGas Distribution LLC submitted a revised baseline filing of their Statement of...

  19. 16 CFR Table 4 to Part 1512 - Relative Energy Distribution of Sources

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Relative Energy Distribution of Sources 4... SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Table 4 Table 4 to Part 1512—Relative Energy Distribution of Sources Wave length (nanometers) Relative energy 380 9.79 390 12.09 400 14.71 410 17.68 420...

  20. 16 CFR Table 4 to Part 1512 - Relative Energy Distribution of Sources

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Relative Energy Distribution of Sources 4... SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Table 4 Table 4 to Part 1512—Relative Energy Distribution of Sources Wave length (nanometers) Relative energy 380 9.79 390 12.09 400 14.71 410 17.68 420...

  1. 16 CFR Table 4 to Part 1512 - Relative Energy Distribution of Sources

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Relative Energy Distribution of Sources 4... SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Table 4 Table 4 to Part 1512—Relative Energy Distribution of Sources Wave length (nanometers) Relative energy 380 9.79 390 12.09 400 14.71 410 17.68 420...

  2. 16 CFR Table 4 to Part 1512 - Relative Energy Distribution of Sources

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Relative Energy Distribution of Sources 4... SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Table 4 Table 4 to Part 1512—Relative Energy Distribution of Sources Wave length (nanometers) Relative energy 380 9.79 390 12.09 400 14.71 410 17.68 420...

  3. 16 CFR Table 4 to Part 1512 - Relative Energy Distribution of Sources

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Relative Energy Distribution of Sources 4... SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Table 4 Table 4 to Part 1512—Relative Energy Distribution of Sources Wave length (nanometers) Relative energy 380 9.79 390 12.09 400 14.71 410 17.68 420...

  4. The planetary distribution of heat sources and sinks during FGGE

    NASA Technical Reports Server (NTRS)

    Johnson, D. R.; Wei, M. Y.

    1985-01-01

    Heating distributions from analysis of the National Meteorological Center and European Center for Medium Range Weather Forecasts data sets; methods used and problems involved in the inference of diabatic heating; the relationship between differential heating and energy transport; and recommendations on the inference of heat soruces and heat sinks for the planetary show are discussed.

  5. Monitoring Design for Source Identification in Water Distribution Systems

    EPA Science Inventory

    The design of sensor networks for the purpose of monitoring for contaminants in water distribution systems is currently an active area of research. Much of the effort has been directed at the contamination detection problem and the expression of public health protection objective...

  6. The distribution and source of boulders on asteroid 4179 Toutatis

    NASA Astrophysics Data System (ADS)

    Jiang, Yun; Ji, Jianghui; Huang, Jiangchuan; Marchi, Simone; Li, Yuan; Ip, Wing-Huen

    2016-01-01

    Boulders are ubiquitous on the surfaces of asteroids and their spatial and size distributions provide information for the geological evolution and collisional history of parent bodies. We identify more than 200 boulders on near-Earth asteroid 4179 Toutatis based on images obtained by Chang'e-2 flyby. The cumulative boulder size frequency distribution (SFD) gives a power-index of -4.4 +/- 0.1, which is clearly steeper than those of boulders on Itokawa and Eros, indicating much high degree of fragmentation. Correlation analyses with craters suggest that most boulders cannot solely be produced as products of cratering, but are probably survived fragments from the parent body of Toutatis, accreted after its breakup. Similar to Itokawa, Toutatis probably has a rubble-pile structure, but owns a different preservation state of boulders.

  7. A comparative study of electric power distribution systems for spacecraft

    NASA Technical Reports Server (NTRS)

    Stuart, Thomas A.; King, Roger J.

    1990-01-01

    The electric power distribution systems for spacecraft are compared concentrating on two interrelated issues: the choice between dc and high frequency ac, and the converter/inverter topology to be used at the power source. The relative merits of dc and ac distribution are discussed. Specific converter and inverter topologies are identified and analyzed in detail for the purpose of detailed comparison. Finally, specific topologies are recommended for use in dc and ac systems.

  8. Optimal source codes for geometrically distributed integer alphabets

    NASA Technical Reports Server (NTRS)

    Gallager, R. G.; Van Voorhis, D. C.

    1975-01-01

    An approach is shown for using the Huffman algorithm indirectly to prove the optimality of a code for an infinite alphabet if an estimate concerning the nature of the code can be made. Attention is given to nonnegative integers with a geometric probability assignment. The particular distribution considered arises in run-length coding and in encoding protocol information in data networks. Questions of redundancy of the optimal code are also investigated.

  9. Comparison of AC losses, magnetic field/current distributions and critical currents of superconducting circular pancake coils and infinitely long stacks using coated conductors

    NASA Astrophysics Data System (ADS)

    Yuan, Weijia; Campbell, A. M.; Hong, Z.; Ainslie, M. D.; Coombs, T. A.

    2010-08-01

    A model is presented for calculating the AC losses, magnetic field/current density distribution and critical currents of a circular superconducting pancake coil. The assumption is that the magnetic flux lines will lie parallel to the wide faces of tapes in the unpenetrated area of the coil. Instead of using an infinitely long stack to approximate the circular coil, this paper gives an exact circular coil model using elliptic integrals. A new efficient numerical method is introduced to yield more accurate and fast computation. The computation results are in good agreement with the assumptions. For a small value of the coil radius, there is an asymmetry along the coil radius direction. As the coil radius increases, this asymmetry will gradually decrease, and the AC losses and penetration depth will increase, but the critical current will decrease. We find that if the internal radius is equal to the winding thickness, the infinitely long stack approximation overestimates the loss by 10% and even if the internal radius is reduced to zero, the error is still only 60%. The infinitely long stack approximation is therefore adequate for most practical purposes. In addition, the comparison result shows that the infinitely long stack approximation saves computation time significantly.

  10. A Mathematical Model to Predict Voltage Fluctuations in a Distribution System with Renewable Energy Sources

    NASA Astrophysics Data System (ADS)

    Iyer, Shivkumar Venkatraman; Wu, Bin; Li, Yunwei; Singh, Birendra

    2015-12-01

    This paper proposes a simplified mathematical model to predict the impact of connection of Distributed Generators (DGs) to the ac grid. The model allows the user to examine the fluctuations in the magnitude of voltages at different nodes in the distribution system. In order to use the model, the user does not require a commercial simulation software making it a handy tool for a practicing engineer. Analysis has been presented to describe how the detailed mathematical model of the system is reduced using elementary matrix manipulation techniques to obtain the final simplified mathematical model. Simulation results are presented to verify the mathematical model with a ring distribution system with three DGs connected to it and the results validate those attained from the mathematical model.

  11. Source-rock distribution model of the periadriatic region

    SciTech Connect

    Zappaterra, E. )

    1994-03-01

    The Periadriatic area is a mosaic of geological provinces comprised of spatially and temporally similar tectonic-sedimentary cycles. Tectonic evolution progressed from a Triassic-Early Jurassic (Liassic) continental rifting stage on the northern edge of the African craton, through an Early Jurassic (Middle Liassic)-Late Cretaceous/Eocene oceanic rifting stage and passive margin formation, to a final continental collision and active margin deformation stage in the Late Cretaceous/Eocene to Holocene. Extensive shallow-water carbonate platform deposits covered large parts of the Periadriatic region in the Late Triassic. Platform breakup and development of a platform-to-basin carbonate shelf morphology began in the Late Triassic and extended through the Cretaceous. On the basis of this paleogeographic evolution, the regional geology of the Periadriatic region can be expressed in terms of three main Upper Triassic-Paleogene sedimentary sequences: (A), the platform sequence; (B), the platform to basin sequence; and (C), the basin sequence. These sequences developed during the initial rifting and subsequent passive-margin formation tectonic stages. The principal Triassic source basins and most of the surface hydrocarbon indications and economically important oil fields of the Periadriatic region are associated with sequence B areas. No major hydrocarbon accumulations can be directly attributed to the Jurassic-Cretaceous epioceanic and intraplatform source rock sequences. The third episode of source bed deposition characterizes the final active margin deformation stage and is represented by Upper Tertiary organic-rich terrigenous units, mostly gas-prone. These are essentially associated with turbiditic and flysch sequences of foredeep basins and have generated the greater part of the commercial biogenic gases of the Periadriatic region. 82 refs., 11 figs., 2 tabs.

  12. Occurrence of arsenic contamination in Canada: sources, behavior and distribution.

    PubMed

    Wang, Suiling; Mulligan, Catherine N

    2006-08-01

    Recently there has been increasing anxieties concerning arsenic related problems. Occurrence of arsenic contamination has been reported worldwide. In Canada, the main natural arsenic sources are weathering and erosion of arsenic-containing rocks and soil, while tailings from historic and recent gold mine operations and wood preservative facilities are the principal anthropogenic sources. Across Canada, the 24-h average concentration of arsenic in the atmosphere is generally less than 0.3 microg/m3. Arsenic concentrations in natural uncontaminated soil and sediments range from 4 to 150 mg/kg. In uncontaminated surface and ground waters, the arsenic concentration ranges from 0.001 to 0.005 mg/L. As a result of anthropogenic inputs, elevated arsenic levels, above ten to thousand times the Interim Maximum Acceptable Concentration (IMAC), have been reported in air, soil and sediment, surface water and groundwater, and biota in several regions. Most arsenic is of toxic inorganic forms. It is critical to recognize that such contamination imposes serious harmful effects on various aquatic and terrestrial organisms and human health ultimately. Serious incidences of acute and chronic arsenic poisonings have been revealed. Through examination of the available literature, screening and selecting existing data, this paper provides an analysis of the currently available information on recognized problem areas, and an overview of current knowledge of the principal hydrogeochemical processes of arsenic transportation and transformation. However, a more detailed understanding of local sources of arsenic and mechanisms of arsenic release is required. More extensive studies will be required for building practical guidance on avoiding and reducing arsenic contamination. Bioremediation and hyperaccumulation are emerging innovative technologies for the remediation of arsenic contaminated sites. Natural attenuation may be utilized as a potential in situ remedial option. Further

  13. Space distribution of extragalactic sources - Cosmology versus evolution

    NASA Technical Reports Server (NTRS)

    Cavaliere, A.; Maccacaro, T.

    1990-01-01

    Alternative cosmologies have been recurrently invoked to explain in terms of global spacetime structure the apparent large increase, with increasing redshift, in the average luminosity of active galactic nuclei. These models interestingly seek to avoid the complexities of the canonical interpretation in terms of intrinsic population evolutions in a Friedmann universe. However, a problem of consistency for these cosmologies is pointed out, since they have to include also other classes of extragalactic sources, such as clusters of galaxies and BL Lac objects, for which there is preliminary evidence of a different behavior.

  14. Utilities for master source code distribution: MAX and Friends

    NASA Technical Reports Server (NTRS)

    Felippa, Carlos A.

    1988-01-01

    MAX is a program for the manipulation of FORTRAN master source code (MSC). This is a technique by which one maintains one and only one master copy of a FORTRAN program under a program developing system, which for MAX is assumed to be VAX/VMS. The master copy is not intended to be directly compiled. Instead it must be pre-processed by MAX to produce compilable instances. These instances may correspond to different code versions (for example, double precision versus single precision), different machines (for example, IBM, CDC, Cray) or different operating systems (i.e., VAX/VMS versus VAX/UNIX). The advantage os using a master source is more pronounced in complex application programs that are developed and maintained over many years and are to be transported and executed on several computer environments. The version lag problem that plagues many such programs is avoided by this approach. MAX is complemented by several auxiliary programs that perform nonessential functions. The ensemble is collectively known as MAX and Friends. All of these programs, including MAX, are executed as foreign VAX/VMS commands and can easily be hidden in customized VMS command procedures.

  15. Dependence of Ozone Generation on Gas Temperature Distribution in AC Atmospheric Pressure Dielectric Barrier Discharge in Oxygen

    NASA Astrophysics Data System (ADS)

    Takahashi, Go; Akashi, Haruaki

    AC atmospheric pressure multi-filament dielectric barrier discharge in oxygen has been simulated using two dimensional fluid model. In the discharge, three kinds of streamers have been obtained. They are primary streamers, small scale streamers and secondary streamers. The primary streamers are main streamers in the discharge and the small scale streamers are formed after the ceasing of the primary streamers. And the secondary streamers are formed on the trace of the primary streamers. In these streamers, the primary and the small scale streamers are very effective to generate O(3P) oxygen atoms which are precursor of ozone. And the ozone is generated mainly in the vicinity of the dielectrics. In high gas temperature region, ozone generation decreases in general. However, increase of the O(3P) oxygen atom density in high gas temperature region compensates decrease of ozone generation rate coefficient. As a result, amount of ozone generation has not changed. But if the effect of gas temperature was neglected, amount of ozone generation increases 10%.

  16. Simulation of dose distribution for iridium-192 brachytherapy source type-H01 using MCNPX

    SciTech Connect

    Purwaningsih, Anik

    2014-09-30

    Dosimetric data for a brachytherapy source should be known before it used for clinical treatment. Iridium-192 source type H01 was manufactured by PRR-BATAN aimed to brachytherapy is not yet known its dosimetric data. Radial dose function and anisotropic dose distribution are some primary keys in brachytherapy source. Dose distribution for Iridium-192 source type H01 was obtained from the dose calculation formalism recommended in the AAPM TG-43U1 report using MCNPX 2.6.0 Monte Carlo simulation code. To know the effect of cavity on Iridium-192 type H01 caused by manufacturing process, also calculated on Iridium-192 type H01 if without cavity. The result of calculation of radial dose function and anisotropic dose distribution for Iridium-192 source type H01 were compared with another model of Iridium-192 source.

  17. Simulation of dose distribution for iridium-192 brachytherapy source type-H01 using MCNPX

    NASA Astrophysics Data System (ADS)

    Purwaningsih, Anik

    2014-09-01

    Dosimetric data for a brachytherapy source should be known before it used for clinical treatment. Iridium-192 source type H01 was manufactured by PRR-BATAN aimed to brachytherapy is not yet known its dosimetric data. Radial dose function and anisotropic dose distribution are some primary keys in brachytherapy source. Dose distribution for Iridium-192 source type H01 was obtained from the dose calculation formalism recommended in the AAPM TG-43U1 report using MCNPX 2.6.0 Monte Carlo simulation code. To know the effect of cavity on Iridium-192 type H01 caused by manufacturing process, also calculated on Iridium-192 type H01 if without cavity. The result of calculation of radial dose function and anisotropic dose distribution for Iridium-192 source type H01 were compared with another model of Iridium-192 source.

  18. Fire Source Localization Based on Distributed Temperature Sensing by a Dual-Line Optical Fiber System

    PubMed Central

    Sun, Miao; Tang, Yuquan; Yang, Shuang; Li, Jun; Sigrist, Markus W.; Dong, Fengzhong

    2016-01-01

    We propose a method for localizing a fire source using an optical fiber distributed temperature sensor system. A section of two parallel optical fibers employed as the sensing element is installed near the ceiling of a closed room in which the fire source is located. By measuring the temperature of hot air flows, the problem of three-dimensional fire source localization is transformed to two dimensions. The method of the source location is verified with experiments using burning alcohol as fire source, and it is demonstrated that the method represents a robust and reliable technique for localizing a fire source also for long sensing ranges. PMID:27275822

  19. Fire Source Localization Based on Distributed Temperature Sensing by a Dual-Line Optical Fiber System.

    PubMed

    Sun, Miao; Tang, Yuquan; Yang, Shuang; Li, Jun; Sigrist, Markus W; Dong, Fengzhong

    2016-01-01

    We propose a method for localizing a fire source using an optical fiber distributed temperature sensor system. A section of two parallel optical fibers employed as the sensing element is installed near the ceiling of a closed room in which the fire source is located. By measuring the temperature of hot air flows, the problem of three-dimensional fire source localization is transformed to two dimensions. The method of the source location is verified with experiments using burning alcohol as fire source, and it is demonstrated that the method represents a robust and reliable technique for localizing a fire source also for long sensing ranges. PMID:27275822

  20. Reconstruction of far-field tsunami amplitude distributions from earthquake sources

    USGS Publications Warehouse

    Geist, Eric L.; Parsons, Thomas E.

    2016-01-01

    The probability distribution of far-field tsunami amplitudes is explained in relation to the distribution of seismic moment at subduction zones. Tsunami amplitude distributions at tide gauge stations follow a similar functional form, well described by a tapered Pareto distribution that is parameterized by a power-law exponent and a corner amplitude. Distribution parameters are first established for eight tide gauge stations in the Pacific, using maximum likelihood estimation. A procedure is then developed to reconstruct the tsunami amplitude distribution that consists of four steps: (1) define the distribution of seismic moment at subduction zones; (2) establish a source-station scaling relation from regression analysis; (3) transform the seismic moment distribution to a tsunami amplitude distribution for each subduction zone; and (4) mix the transformed distribution for all subduction zones to an aggregate tsunami amplitude distribution specific to the tide gauge station. The tsunami amplitude distribution is adequately reconstructed for four tide gauge stations using globally constant seismic moment distribution parameters established in previous studies. In comparisons to empirical tsunami amplitude distributions from maximum likelihood estimation, the reconstructed distributions consistently exhibit higher corner amplitude values, implying that in most cases, the empirical catalogs are too short to include the largest amplitudes. Because the reconstructed distribution is based on a catalog of earthquakes that is much larger than the tsunami catalog, it is less susceptible to the effects of record-breaking events and more indicative of the actual distribution of tsunami amplitudes.

  1. Reconstruction of Far-Field Tsunami Amplitude Distributions from Earthquake Sources

    NASA Astrophysics Data System (ADS)

    Geist, Eric L.; Parsons, Tom

    2016-04-01

    The probability distribution of far-field tsunami amplitudes is explained in relation to the distribution of seismic moment at subduction zones. Tsunami amplitude distributions at tide gauge stations follow a similar functional form, well described by a tapered Pareto distribution that is parameterized by a power-law exponent and a corner amplitude. Distribution parameters are first established for eight tide gauge stations in the Pacific, using maximum likelihood estimation. A procedure is then developed to reconstruct the tsunami amplitude distribution that consists of four steps: (1) define the distribution of seismic moment at subduction zones; (2) establish a source-station scaling relation from regression analysis; (3) transform the seismic moment distribution to a tsunami amplitude distribution for each subduction zone; and (4) mix the transformed distribution for all subduction zones to an aggregate tsunami amplitude distribution specific to the tide gauge station. The tsunami amplitude distribution is adequately reconstructed for four tide gauge stations using globally constant seismic moment distribution parameters established in previous studies. In comparisons to empirical tsunami amplitude distributions from maximum likelihood estimation, the reconstructed distributions consistently exhibit higher corner amplitude values, implying that in most cases, the empirical catalogs are too short to include the largest amplitudes. Because the reconstructed distribution is based on a catalog of earthquakes that is much larger than the tsunami catalog, it is less susceptible to the effects of record-breaking events and more indicative of the actual distribution of tsunami amplitudes.

  2. An altitude and distance correction to the source fluence distribution of TGFs

    PubMed Central

    Nisi, R S; Østgaard, N; Gjesteland, T; Collier, A B

    2014-01-01

    The source fluence distribution of terrestrial gamma ray flashes (TGFs) has been extensively discussed in recent years, but few have considered how the TGF fluence distribution at the source, as estimated from satellite measurements, depends on the distance from satellite foot point and assumed production altitude. As the absorption of the TGF photons increases significantly with lower source altitude and larger distance between the source and the observing satellite, these might be important factors. We have addressed the issue by using the tropopause pressure distribution as an approximation of the TGF production altitude distribution and World Wide Lightning Location Network spheric measurements to determine the distance. The study is made possible by the increased number of Ramaty High Energy Solar Spectroscopic Imager (RHESSI) TGFs found in the second catalog of the RHESSI data. One find is that the TGF/lightning ratio for the tropics probably has an annual variability due to an annual variability in the Dobson-Brewer circulation. The main result is an indication that the altitude distribution and distance should be considered when investigating the source fluence distribution of TGFs, as this leads to a softening of the inferred distribution of source brightness. PMID:26167434

  3. An altitude and distance correction to the source fluence distribution of TGFs

    NASA Astrophysics Data System (ADS)

    Nisi, R. S.; Østgaard, N.; Gjesteland, T.; Collier, A. B.

    2014-10-01

    The source fluence distribution of terrestrial gamma ray flashes (TGFs) has been extensively discussed in recent years, but few have considered how the TGF fluence distribution at the source, as estimated from satellite measurements, depends on the distance from satellite foot point and assumed production altitude. As the absorption of the TGF photons increases significantly with lower source altitude and larger distance between the source and the observing satellite, these might be important factors. We have addressed the issue by using the tropopause pressure distribution as an approximation of the TGF production altitude distribution and World Wide Lightning Location Network spheric measurements to determine the distance. The study is made possible by the increased number of Ramaty High Energy Solar Spectroscopic Imager (RHESSI) TGFs found in the second catalog of the RHESSI data. One find is that the TGF/lightning ratio for the tropics probably has an annual variability due to an annual variability in the Dobson-Brewer circulation. The main result is an indication that the altitude distribution and distance should be considered when investigating the source fluence distribution of TGFs, as this leads to a softening of the inferred distribution of source brightness.

  4. Decoy-state quantum key distribution with a leaky source

    NASA Astrophysics Data System (ADS)

    Tamaki, Kiyoshi; Curty, Marcos; Lucamarini, Marco

    2016-06-01

    In recent years, there has been a great effort to prove the security of quantum key distribution (QKD) with a minimum number of assumptions. Besides its intrinsic theoretical interest, this would allow for larger tolerance against device imperfections in the actual implementations. However, even in this device-independent scenario, one assumption seems unavoidable, that is, the presence of a protected space devoid of any unwanted information leakage in which the legitimate parties can privately generate, process and store their classical data. In this paper we relax this unrealistic and hardly feasible assumption and introduce a general formalism to tackle the information leakage problem in most of existing QKD systems. More specifically, we prove the security of optical QKD systems using phase and intensity modulators in their transmitters, which leak the setting information in an arbitrary manner. We apply our security proof to cases of practical interest and show key rates similar to those obtained in a perfectly shielded environment. Our work constitutes a fundamental step forward in guaranteeing implementation security of quantum communication systems.

  5. Measurements of Infrared and Acoustic Source Distributions in Jet Plumes

    NASA Technical Reports Server (NTRS)

    Agboola, Femi A.; Bridges, James; Saiyed, Naseem

    2004-01-01

    The aim of this investigation was to use the linear phased array (LPA) microphones and infrared (IR) imaging to study the effects of advanced nozzle-mixing techniques on jet noise reduction. Several full-scale engine nozzles were tested at varying power cycles with the linear phased array setup parallel to the jet axis. The array consisted of 16 sparsely distributed microphones. The phased array microphone measurements were taken at a distance of 51.0 ft (15.5 m) from the jet axis, and the results were used to obtain relative overall sound pressure levels from one nozzle design to the other. The IR imaging system was used to acquire real-time dynamic thermal patterns of the exhaust jet from the nozzles tested. The IR camera measured the IR radiation from the nozzle exit to a distance of six fan diameters (X/D(sub FAN) = 6), along the jet plume axis. The images confirmed the expected jet plume mixing intensity, and the phased array results showed the differences in sound pressure level with respect to nozzle configurations. The results show the effects of changes in configurations to the exit nozzles on both the flows mixing patterns and radiant energy dissipation patterns. By comparing the results from these two measurements, a relationship between noise reduction and core/bypass flow mixing is demonstrated.

  6. Optimal source distribution for binaural synthesis over loudspeakers

    NASA Astrophysics Data System (ADS)

    Takeuchi, Takashi; Nelson, Philip A.

    2002-12-01

    When binaural sound signals are presented with loudspeakers, the system inversion involved gives rise to a number of problems such as a loss of dynamic range and a lack of robustness to small errors and room reflections. The amplification required by the system inversion results in loss of dynamic range. The control performance of such a system deteriorates severely due to small errors resulting from, e.g., misalignment of the system and individual differences in the head related transfer functions at certain frequencies. The required large sound radiation results in severe reflection which also reduces the control performance. A method of overcoming these fundamental problems is proposed in this paper. A conceptual monopole transducer is introduced whose position varies continuously as frequency varies. This gives a minimum processing requirement of the binaural signals for the control to be achieved and all the above problems either disappear or are minimized. The inverse filters have flat amplitude response and the reproduced sound is not colored even outside the relatively large ``sweet area.'' A number of practical solutions are suggested for the realization of such optimally distributed transducers. One of them is a discretization that enables the use of conventional transducer units.

  7. Differential dose contributions on total dose distribution of 125I brachytherapy source

    PubMed Central

    Camgöz, B.; Yeğin, G.; Kumru, M.N.

    2010-01-01

    This work provides an improvement of the approach using Monte Carlo simulation for the Amersham Model 6711 125I brachytherapy seed source, which is well known by many theoretical and experimental studies. The source which has simple geometry was researched with respect to criteria of AAPM Tg-43 Report. The approach offered by this study involves determination of differential dose contributions that come from virtual partitions of a massive radioactive element of the studied source to a total dose at analytical calculation point. Some brachytherapy seeds contain multi-radioactive elements so the dose at any point is a total of separate doses from each element. It is momentous to know well the angular and radial dose distributions around the source that is located in cancerous tissue for clinical treatments. Interior geometry of a source is effective on dose characteristics of a distribution. Dose information of inner geometrical structure of a brachytherapy source cannot be acquired by experimental methods because of limits of physical material and geometry in the healthy tissue, so Monte Carlo simulation is a required approach of the study. EGSnrc Monte Carlo simulation software was used. In the design of a simulation, the radioactive source was divided into 10 rings, partitioned but not separate from each other. All differential sources were simulated for dose calculation, and the shape of dose distribution was determined comparatively distribution of a single-complete source. In this work anisotropy function was examined also mathematically. PMID:24376927

  8. GEOCHEMISTRY OF PAHS IN AQUATIC ENVIRONMENTS: A SYNTHESIS OF DISTRIBUTION, SOURCE, PERSISTENCE, PARTITIONING AND BIOAVAILABILITY

    EPA Science Inventory

    On the basis of their distributions, sources, persistence, partitioning and bioavailability, polycyclic aromatic hydrocarbons (PAHs) are a unique class of persistent organic pollutants (POPs) contaminating the aquatic environment. They are of particular interest to geochemists an...

  9. A study of the distribution of the noise source strengths in coaxial double jet

    NASA Astrophysics Data System (ADS)

    Nakazono, Y.

    1983-05-01

    The apparent noise source distributions in a coaxial double jet at subsonic speed were determined using a reflector-type directional microphone system which has an elliptical concave mirror with a diameter of 40 cm. It was found that the 1/3 octave band sound pressure spectrum in the far-field which was calculated with the sound source distribution agreed with the results obtained by an omnidirectional microphone at each velocity ratio of the bypass jet to the core jet. These results indicate that the directional microphone system will be a highly effective tool for the measurement of the sound source strength distribution of a coaxial double jet as well as that of a single jet. In addition, the overall pressure fluctuations in the jet flow were measured at each velocity ratio, and the influence of the correlation upon the far-field noise was examined based on the pressure fluctuations and the noise source distribution.

  10. Comparing two micrometeorological techniques for estimating trace gas emissions from distributed sources

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Measuring trace gas emission from distributed sources such as treatment lagoons, treatment wetlands, land spread of manure, and feedlots requires micrometeorological methods. In this study, we tested the accuracy of two relatively new micrometeorological techniques, vertical radial plume mapping (VR...

  11. 26 CFR 1.316-2 - Sources of distribution in general.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... earnings and profits. In determining the source of a distribution, consideration should be given first, to.... (b) If the earnings and profits of the taxable year (computed as of the close of the year...

  12. 26 CFR 1.316-2 - Sources of distribution in general.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... earnings and profits. In determining the source of a distribution, consideration should be given first, to.... (b) If the earnings and profits of the taxable year (computed as of the close of the year...

  13. 26 CFR 1.316-2 - Sources of distribution in general.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... earnings and profits. In determining the source of a distribution, consideration should be given first, to.... (b) If the earnings and profits of the taxable year (computed as of the close of the year...

  14. 26 CFR 1.316-2 - Sources of distribution in general.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... and profits. In determining the source of a distribution, consideration should be given first, to the... earnings and profits of the taxable year (computed as of the close of the year without diminution by...

  15. 26 CFR 1.316-2 - Sources of distribution in general.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... and profits. In determining the source of a distribution, consideration should be given first, to the... earnings and profits of the taxable year (computed as of the close of the year without diminution by...

  16. Voltage controller/current limiter for ac

    NASA Technical Reports Server (NTRS)

    Wu, T. T.

    1980-01-01

    Circuit protects ac power systems for overload failures, limits power surge and short-circuit currents to 150 percent of steady state level, regulates ac output voltage, and soft starts loads. Limiter generates dc error signal in response to line fluctuations and dumps power when overload is reached. Device is inserted between ac source and load.

  17. Sources and distribution of trace elements in Estonian peat

    NASA Astrophysics Data System (ADS)

    Orru, Hans; Orru, Mall

    2006-10-01

    This paper presents the results of the distribution of trace elements in Estonian mires. Sixty four mires, representative of the different landscape units, were analyzed for the content of 16 trace elements (Cr, Mn, Ni, Cu, Zn, and Pb using AAS; Cd by GF-AAS; Hg by the cold vapour method; and V, Co, As, Sr, Mo, Th, and U by XRF) as well as other peat characteristics (peat type, degree of humification, pH and ash content). The results of the research show that concentrations of trace elements in peat are generally low: V 3.8 ± 0.6, Cr 3.1 ± 0.2, Mn 35.1 ± 2.7, Co 0.50 ± 0.05, Ni 3.7 ± 0.2, Cu 4.4 ± 0.3, Zn 10.0 ± 0.7, As 2.4 ± 0.3, Sr 21.9 ± 0.9, Mo 1.2 ± 0.2, Cd 0.12 ± 0.01, Hg 0.05 ± 0.01, Pb 3.3 ± 0.2, Th 0.47 ± 0.05, U 1.3 ± 0.2 μg g - 1 and S 0.25 ± 0.02%. Statistical analyses on these large database showed that Co has the highest positive correlations with many elements and ash content. As, Ni, Mo, ash content and pH are also significantly correlated. The lowest abundance of most trace elements was recorded in mires fed only by precipitation (ombrotrophic), and the highest in mires fed by groundwater and springs (minerotrophic), which are situated in the flood plains of river valleys. Concentrations usually differ between the superficial, middle and bottom peat layers, but the significance decreases depending on the type of mire in the following order: transitional mires - raised bogs - fens. Differences among mire types are highest for the superficial but not significant for the basal peat layers. The use of peat with high concentrations of trace elements in agriculture, horticulture, as fuel, for water purification etc., may pose a risk for humans: via the food chain, through inhalation, drinking water etc.

  18. Elevated Natural Source Water Ammonia and Nitrification in the Distribution Systems of Four Water Utilities

    EPA Science Inventory

    Nitrification in drinking water distribution systems is a concern of many drinking water systems. Although chloramination as a source of nitrification (i.e., addition of excess ammonia or breakdown of chloramines) has drawn the most attention, many source waters contain signific...

  19. Response of a viscoelastic halfspace to subsurface distributed acoustic sources with application to medical diagnosis

    NASA Astrophysics Data System (ADS)

    Royston, Thomas J.; Yazicioglu, Yigit; Loth, Francis

    2003-04-01

    The response within and at the surface of an isotropic viscoelastic medium to subsurface distributed low audible frequency acoustic sources is considered. Spherically and cylindrically distributed sources are approximated as arrays of infinitesimal point sources. Analytical approximations for the acoustic field radiating from these sources are then obtained as a summation of tractable point source expressions. These theoretical approximations are compared to computational finite element predictions and experimental studies in selected cases. The objective is to better understand low audible frequency sound propagation in soft biological tissue caused by subsurface sources. Distributed acoustic sources could represent vibratory motion of the vascular wall caused by turbulent blood flow past a constriction (stenosis). Additionally focused vibratory stimulation using a dynamic radiation force caused by interfering ultrasound beams effectively creates a distributed subsurface acoustic source. A dynamic radiation force has been investigated as a means of probing subsurface tissue anomalies, including calcified vascular plaque and tumorous growths. In these cases, there is an interest in relating acoustic measurements at the skin surface and within the medium to the underlying flow/constriction environment or tissue anomaly. [Research supported by NIH NCRR 14250 and Whitaker Foundation BME RG 01-0198.

  20. Energy decay for viscoelastic plates with distributed delay and source term

    NASA Astrophysics Data System (ADS)

    Mustafa, Muhammad I.; Kafini, Mohammad

    2016-06-01

    In this paper we consider a viscoelastic plate equation with distributed delay and source term. Under suitable conditions on the delay and source term, we establish an explicit and general decay rate result without imposing restrictive assumptions on the behavior of the relaxation function at infinity. Our result allows a wider class of relaxation functions and improves earlier results in the literature.

  1. Numerical analysis of atomic density distribution in arc driven negative ion sources

    SciTech Connect

    Yamamoto, T. Shibata, T.; Hatayama, A.; Kashiwagi, M.; Hanada, M.; Sawada, K.

    2014-02-15

    The purpose of this study is to calculate atomic (H{sup 0}) density distribution in JAEA 10 ampere negative ion source. A collisional radiative model is developed for the calculation of the H{sup 0} density distribution. The non-equilibrium feature of the electron energy distribution function (EEDF), which mainly determines the H{sup 0} production rate, is included by substituting the EEDF calculated from 3D electron transport analysis. In this paper, the H{sup 0} production rate, the ionization rate, and the density distribution in the source chamber are calculated. In the region where high energy electrons exist, the H{sup 0} production and the ionization are enhanced. The calculated H{sup 0} density distribution without the effect of the H{sup 0} transport is relatively small in the upper region. In the next step, the effect should be taken into account to obtain more realistic H{sup 0} distribution.

  2. Correlated Sources in Distributed Networks--Data Transmission, Common Information Characterization and Inferencing

    ERIC Educational Resources Information Center

    Liu, Wei

    2011-01-01

    Correlation is often present among observations in a distributed system. This thesis deals with various design issues when correlated data are observed at distributed terminals, including: communicating correlated sources over interference channels, characterizing the common information among dependent random variables, and testing the presence of…

  3. Measurement Technique of Dose Rate Distribution of Ionization Sources with Unstable in Time Beam Parameters

    NASA Astrophysics Data System (ADS)

    Stuchebrov, S. G.; Miloichikova, I. A.; Danilova, I. B.

    2016-01-01

    The article describes a new technique for the average values of radiation dose measurement for the unstable gamma-ray sources which are used in non-destructive testing. The method is based on usage of different types of compact accumulative dosimeters. Spatially distributed position sensitive dosimetry system based on compact sensitive elements was created. Size and spatial resolution of the system of the dosimetry system are chosen taking into account sources characteristics. The proposed method has been tested on the measurement of dose distribution of several sources of X-ray and gamma-radiation based on X-ray tubes, electronic accelerator betatrons and linear electron accelerators.

  4. Modeling Heat Flow for a Distributed Moving Heat Source in Micro-Laser Welding of Plastics

    NASA Astrophysics Data System (ADS)

    Grewell, David; Benatar, Avraham

    2004-06-01

    Polymer use in micro-devices, especially in the medical industry has been rapidly increasing. During assembly of micro-devices it is desirable to produce weld joints that are about 100 μm in width. This paper reviews the modeling of heat flow during through transmission infrared micro-welding of plastic using fiber coupled laser diodes. Two models were used to predict the temperature distributions within welded samples. Both models were based on a moving heat source and moving coordinate system. For the simpler model a moving point heat source was used and for the more complex model a Gaussian distributed heat source was used. It was found that the distributed model can accurately predict temperature fields in plastic laser welds for all ranges of the parameters evaluated. However, the point heat source model was only able to accurately predict temperature fields with a relatively small laser focal spot (25 μm). In addition it was found that for micro-welding of plastics, when the dimensionless distribution parameter is less than two, a point heat source model predicts similar widths to those predicted by a distributed heat source model.

  5. Optical fiber bundle displacement sensor using an ac-modulated light source with subnanometer resolution and low thermal drift

    NASA Astrophysics Data System (ADS)

    Shimamoto, Atsushi; Tanaka, Kohichi

    1995-09-01

    An optical fiber bundle displacement sensor with subnanometer order resolution and low thermal drift is proposed. The setup is based on a carrier amplifier system and involves techniques to eliminate fluctuation in the light power of the source. The achieved noise level of the sensor was 0.03 nm/ \\radical Hz \\end-radical . The stability was estimated by comparing the outputs of two different sensors from the same target for 4 ks (67 min). The relative displacements between the fiber bundle ends of the two sensors and the target surface varied in the area of 400 nm depending on the ambient temperature variation at 2 deg C. However, the difference in output between the two sensor systems is within 2 nm for more than 1 hour of measurement. It is expected that it would be reduced to within the area of 0.1 nm if the ambient temperature were controlled to within +/-0.1 deg C. It is concluded that the stability of the sensors is sufficiently good to be used with nanotechnological instruments.

  6. The Integration of Renewable Energy Sources into Electric Power Distribution Systems, Vol. II Utility Case Assessments

    SciTech Connect

    Zaininger, H.W.

    1994-01-01

    Electric utility distribution system impacts associated with the integration of renewable energy sources such as photovoltaics (PV) and wind turbines (WT) are considered in this project. The impacts are expected to vary from site to site according to the following characteristics: the local solar insolation and/or wind characteristics, renewable energy source penetration level, whether battery or other energy storage systems are applied, and local utility distribution design standards and planning practices. Small, distributed renewable energy sources are connected to the utility distribution system like other, similar kW- and MW-scale equipment and loads. Residential applications are expected to be connected to single-phase 120/240-V secondaries. Larger kW-scale applications may be connected to three+phase secondaries, and larger hundred-kW and y-scale applications, such as MW-scale windfarms, or PV plants, may be connected to electric utility primary systems via customer-owned primary and secondary collection systems. In any case, the installation of small, distributed renewable energy sources is expected to have a significant impact on local utility distribution primary and secondary system economics. Small, distributed renewable energy sources installed on utility distribution systems will also produce nonsite-specific utility generation system benefits such as energy and capacity displacement benefits, in addition to the local site-specific distribution system benefits. Although generation system benefits are not site-specific, they are utility-specific, and they vary significantly among utilities in different regions. In addition, transmission system benefits, environmental benefits and other benefits may apply. These benefits also vary significantly among utilities and regions. Seven utility case studies considering PV, WT, and battery storage were conducted to identify a range of potential renewable energy source distribution system applications. The

  7. Distribution of terminal electron-accepting processes in an aquifer having multiple contaminant sources

    USGS Publications Warehouse

    McMahon, P.B.; Bruce, B.W.

    1997-01-01

    Concentrations of electron acceptors, electron donors, and H2 in groundwater were measured to determine the distribution of terminal electron-accepting processes (TEAPs) in an alluvial aquifer having multiple contaminant sources. Upgradient contaminant sources included two separate hydrocarbon point sources, one of which contained the fuel oxygenate methyl tertbutyl ether (MTBE). Infiltrating river water was a source of dissolved NO31 SO4 and organic carbon (DOC) to the downgradient part of the aquifer. Groundwater downgradient from the MTBE source had larger concentrations of electron acceptors (dissolved O2 and SO4) and smaller concentrations of TEAP end products (dissolved inorganic C, Fe2+ and CH4) than groundwater downgradient from the other hydrocarbon source, suggesting that MTBE was not as suitable for supporting TEAPs as the other hydrocarbons. Measurements of dissolved H2 indicated that SO4 reduction predominated in the aquifer during a period of high water levels in the aquifer and river. The predominant TEAP shifted to Fe3+ reduction in upgradient areas after water levels receded but remained SO4 reducing downgradient near the river. This distribution of TEAPs is the opposite of what is commonly observed in aquifers having a single contaminant point source and probably reflects the input of Dec and SO4 to the aquifer from the river. Results of this study indicate that the distribution of TEAPs in aquifers having multiple contaminant sources depends on the composition and location of the contaminants and on the availability of electron acceptors.

  8. Integrating distributed data sources with OGSA-DAI DQP and VIEWS.

    PubMed

    Dobrzelecki, Bartosz; Krause, Amrey; Hume, Alastair C; Grant, Alistair; Antonioletti, Mario; Alemu, Tilaye Y; Atkinson, Malcolm; Jackson, Mike; Theocharopoulos, Elias

    2010-09-13

    OGSA-DAI (Open Grid Services Architecture Data Access and Integration) is a framework for building distributed data access and integration systems. Until recently, it lacked the built-in functionality that would allow easy creation of federations of distributed data sources. The latest release of the OGSA-DAI framework introduced the OGSA-DAI DQP (Distributed Query Processing) resource. The new resource encapsulates a distributed query processor, that is able to orchestrate distributed data sources when answering declarative user queries. The query processor has many extensibility points, making it easy to customize. We have also introduced a new OGSA-DAI Views resource that provides a flexible method for defining views over relational data. The interoperability of the two new resources, together with the flexibility of the OGSA-DAI framework, allows the building of highly customized data integration solutions. PMID:20679127

  9. The impact of light source spectral power distribution on sky glow

    NASA Astrophysics Data System (ADS)

    Luginbuhl, Christian B.; Boley, Paul A.; Davis, Donald R.

    2014-05-01

    The effect of light source spectral power distribution on the visual brightness of anthropogenic sky glow is described. Under visual adaptation levels relevant to observing the night sky, namely with dark-adapted (scotopic) vision, blue-rich (“white”) sources produce a dramatically greater sky brightness than yellow-rich sources. High correlated color temperature LEDs and metal halide sources produce a visual brightness up to 8× brighter than low-pressure sodium and 3× brighter than high-pressure sodium when matched lumen-for-lumen and observed nearby. Though the sky brightness arising from blue-rich sources decreases more strongly with distance, the visual sky glow resulting from such sources remains significantly brighter than from yellow sources out to the limits of this study at 300 km.

  10. Effect of tissue inhomogeneities on dose distributions from Cf-252 brachytherapy source.

    PubMed

    Ghassoun, J

    2013-01-01

    The Monte Carlo method was used to determine the effect of tissue inhomogeneities on dose distribution from a Cf-252 brachytherapy source. Neutron and gamma-ray fluences, energy spectra and dose rate distributions were determined in both homogenous and inhomogeneous phantoms. Simulations were performed using the MCNP5 code. Obtained results were compared with experimentally measured values published in literature. Results showed a significant change in neutron dose rate distributions in presence of heterogeneities. However, their effect on gamma rays dose distribution is minimal. PMID:23069196

  11. Explicit estimation of higher order modes in fission source distribution of Monte-Carlo calculation

    SciTech Connect

    Yamamoto, A.; Sakata, K.; Endo, T.

    2013-07-01

    Magnitude of higher order modes in fission source distribution of a multi-group Monte-Carlo calculation is estimated using the orthogonal property of forward and adjoint fission source distributions. Calculation capability of the forward and adjoint fission source distributions for fundamental and higher order modes are implemented in the AEGIS code, which is a two-dimensional transport code based on the method of characteristics. With the calculation results of the AEGIS code, magnitudes of the first to fifth higher order modes in fission source distribution obtained by the multi-group Monte-Carlo code GMVP are estimated. There are two contributions in the present study - (1) establishment of a surrogate model, which represents convergence of fission source distribution taking into account the inherent statistical 'noise' of higher order modes of Monte-Carlo calculations and (2) independent confirmation of the estimated dominance ratio in a Monte-Carlo calculation. The surrogate model would contribute to studies of the inter-cycle correlation and estimation of sufficient number of inactive/active cycles. (authors)

  12. Sources and distribution of late Pleistocene sand, northern Gulf of Mexico Shelf

    SciTech Connect

    Mazzullo, J.M.; Bates, C.; Reutter, D.; Withers, K.

    1985-02-01

    A completed 3-yr study of the sources and consequent distribution of late Pleistocene sand on the northern Gulf shelf clarifies paleogeography and alluvial identification. Techniques used to determine the sources of sand are: the Fourier technique (which differentiated sands from different source terranes on the basis of the shapes of quartz sand grains), mineralogic analysis (which identified the composition of the source terranes that contributed each quartz-shape type), and an evaluation of the source terranes drained by each of the southern US rivers (thereby linking each shape type to a particular river). These data and the mapped distribution of sand deposited on the shelf by each of these rivers during the late Pleistocene lowstand indicate distribution patterns have not been modified by modern shelf currents to any great extent, and thus record the late Pleistocene paleogeography of the shelf. These distributions show, among other things, the locations of the late Pleistocene alluvial valleys of each of the southern US rivers, and identify the sources of shelf-edge deltas off the coasts of Texas and Louisiana that were detected by shallow seismic analysis.

  13. The Impact of Source Distribution on Scalar Transport over Forested Hills

    NASA Astrophysics Data System (ADS)

    Ross, Andrew N.; Harman, Ian N.

    2015-08-01

    Numerical simulations of neutral flow over a two-dimensional, isolated, forested ridge are conducted to study the effects of scalar source distribution on scalar concentrations and fluxes over forested hills. Three different constant-flux sources are considered that span a range of idealized but ecologically important source distributions: a source at the ground, one uniformly distributed through the canopy, and one decaying with depth in the canopy. A fourth source type, where the in-canopy source depends on both the wind speed and the difference in concentration between the canopy and a reference concentration on the leaf, designed to mimic deposition, is also considered. The simulations show that the topographically-induced perturbations to the scalar concentration and fluxes are quantitatively dependent on the source distribution. The net impact is a balance of different processes affecting both advection and turbulent mixing, and can be significant even for moderate topography. Sources that have significant input in the deep canopy or at the ground exhibit a larger magnitude advection and turbulent flux-divergence terms in the canopy. The flows have identical velocity fields and so the differences are entirely due to the different tracer concentration fields resulting from the different source distributions. These in-canopy differences lead to larger spatial variations in above-canopy scalar fluxes for sources near the ground compared to cases where the source is predominantly located near the canopy top. Sensitivity tests show that the most significant impacts are often seen near to or slightly downstream of the flow separation or reattachment points within the canopy flow. The qualitative similarities to previous studies using periodic hills suggest that important processes occurring over isolated and periodic hills are not fundamentally different. The work has important implications for the interpretation of flux measurements over forests, even in

  14. The integration of renewable energy sources into electric power distribution systems. Volume 2, Utility case assessments

    SciTech Connect

    Zaininger, H.W.; Ellis, P.R.; Schaefer, J.C.

    1994-06-01

    Electric utility distribution system impacts associated with the integration of renewable energy sources such as photovoltaics (PV) and wind turbines (WT) are considered in this project. The impacts are expected to vary from site to site according to the following characteristics: (1) The local solar insolation and/or wind characteristics; (2) renewable energy source penetration level; (3) whether battery or other energy storage systems are applied; and (4) local utility distribution design standards and planning practices. Small, distributed renewable energy sources are connected to the utility distribution system like other, similar kW- and MW-scale equipment and loads. Residential applications are expected to be connected to single-phase 120/240-V secondaries. Larger kw-scale applications may be connected to three-phase secondaries, and larger hundred-kW and MW-scale applications, such as MW-scale windfarms or PV plants, may be connected to electric utility primary systems via customer-owned primary and secondary collection systems. Small, distributed renewable energy sources installed on utility distribution systems will also produce nonsite-specific utility generation system benefits such as energy and capacity displacement benefits, in addition to the local site-specific distribution system benefits. Although generation system benefits are not site-specific, they are utility-specific, and they vary significantly among utilities in different regions. In addition, transmission system benefits, environmental benefits and other benefits may apply. These benefits also vary significantly among utilities and regions. Seven utility case studies considering PV, WT, and battery storage were conducted to identify a range of potential renewable energy source distribution system applications.

  15. Using sediment particle size distribution to evaluate sediment sources in the Tobacco Creek Watershed

    NASA Astrophysics Data System (ADS)

    Liu, Cenwei; Lobb, David; Li, Sheng; Owens, Philip; Kuzyk, ZouZou

    2014-05-01

    Lake Winnipeg has recently brought attention to the deteriorated water quality due to in part to nutrient and sediment input from agricultural land. Improving water quality in Lake Winnipeg requires the knowledge of the sediment sources within this ecosystem. There are a variety of environmental fingerprinting techniques have been successfully used in the assessment of sediment sources. In this study, we used particle size distribution to evaluate spatial and temporal variations of suspended sediment and potential sediment sources collected in the Tobacco Creek Watershed in Manitoba, Canada. The particle size distribution of suspended sediment can reflect the origin of sediment and processes during sediment transport, deposition and remobilization within the watershed. The objectives of this study were to quantify visually observed spatial and temporal changes in sediment particles, and to assess the sediment source using a rapid and cost-effective fingerprinting technique based on particle size distribution. The suspended sediment was collected by sediment traps twice a year during rainfall and snowmelt periods from 2009 to 2012. The potential sediment sources included the top soil of cultivated field, riparian area and entire profile from stream banks. Suspended sediment and soil samples were pre-wet with RO water and sieved through 600 μm sieve before analyzing. Particle size distribution of all samples was determined using a Malvern Mastersizer 2000S laser diffraction with the measurement range up to 600μm. Comparison of the results for different fractions of sediment showed significant difference in particle size distribution of suspended sediment between snowmelt and rainfall events. An important difference of particle size distribution also found between the cultivated soil and forest soil. This difference can be explained by different land uses which provided a distinct fingerprint of sediment. An overall improvement in water quality can be achieved by

  16. Source coding with escort distributions and Rényi entropy bounds

    NASA Astrophysics Data System (ADS)

    Bercher, J.-F.

    2009-08-01

    We discuss the interest of escort distributions and Rényi entropy in the context of source coding. We first recall a source coding theorem by Campbell relating a generalized measure of length to the Rényi-Tsallis entropy. We show that the associated optimal codes can be obtained using considerations on escort-distributions. We propose a new family of measure of length involving escort-distributions and we show that these generalized lengths are also bounded below by the Rényi entropy. Furthermore, we obtain that the standard Shannon codes lengths are optimum for the new generalized lengths measures, whatever the entropic index. Finally, we show that there exists in this setting an interplay between standard and escort distributions.

  17. AC photovoltaic module magnetic fields

    SciTech Connect

    Jennings, C.; Chang, G.J.; Reyes, A.B.; Whitaker, C.M.

    1997-12-31

    Implementation of alternating current (AC) photovoltaic (PV) modules, particularly for distributed applications such as PV rooftops and facades, may be slowed by public concern about electric and magnetic fields (EMF). This paper documents magnetic field measurements on an AC PV module, complementing EMF research on direct-current PV modules conducted by PG and E in 1993. Although not comprehensive, the PV EMF data indicate that 60 Hz magnetic fields (the EMF type of greatest public concern) from PV modules are comparable to, or significantly less than, those from household appliances. Given the present EMF research knowledge, AC PV module EMF may not merit considerable concern.

  18. Strategies for satellite-based monitoring of CO2 from distributed area and point sources

    NASA Astrophysics Data System (ADS)

    Schwandner, Florian M.; Miller, Charles E.; Duren, Riley M.; Natraj, Vijay; Eldering, Annmarie; Gunson, Michael R.; Crisp, David

    2014-05-01

    Atmospheric CO2 budgets are controlled by the strengths, as well as the spatial and temporal variabilities of CO2 sources and sinks. Natural CO2 sources and sinks are dominated by the vast areas of the oceans and the terrestrial biosphere. In contrast, anthropogenic and geogenic CO2 sources are dominated by distributed area and point sources, which may constitute as much as 70% of anthropogenic (e.g., Duren & Miller, 2012), and over 80% of geogenic emissions (Burton et al., 2013). Comprehensive assessments of CO2 budgets necessitate robust and highly accurate satellite remote sensing strategies that address the competing and often conflicting requirements for sampling over disparate space and time scales. Spatial variability: The spatial distribution of anthropogenic sources is dominated by patterns of production, storage, transport and use. In contrast, geogenic variability is almost entirely controlled by endogenic geological processes, except where surface gas permeability is modulated by soil moisture. Satellite remote sensing solutions will thus have to vary greatly in spatial coverage and resolution to address distributed area sources and point sources alike. Temporal variability: While biogenic sources are dominated by diurnal and seasonal patterns, anthropogenic sources fluctuate over a greater variety of time scales from diurnal, weekly and seasonal cycles, driven by both economic and climatic factors. Geogenic sources typically vary in time scales of days to months (geogenic sources sensu stricto are not fossil fuels but volcanoes, hydrothermal and metamorphic sources). Current ground-based monitoring networks for anthropogenic and geogenic sources record data on minute- to weekly temporal scales. Satellite remote sensing solutions would have to capture temporal variability through revisit frequency or point-and-stare strategies. Space-based remote sensing offers the potential of global coverage by a single sensor. However, no single combination of orbit

  19. Computer simulation of PPF distribution under blue and red LED light source for plant growth.

    PubMed

    Takita, S; Okamoto, K; Yanagi, T

    1996-12-01

    The superimposed pattern of "luminescence spectrum of blue light emitting diode (LED)" and "that of red LED", corresponds well to light absorption spectrum of chlorophyll. If these two kinds of LED are used as a light source, various plant cultivation experiments are possible. The cultivation experiments which use such light sources are becoming increasingly active, and in such experiments, it is very important to know the distribution of the photosynthetic photon flux (PPF) which exerts an important influence on photosynthesis. Therefore, we have developed a computer simulation system which can visualize the PPF distribution under a light source equipped with blue and red LEDs. In this system, an LED is assumed to be a point light source, and only the photons which are emitted directly from LED are considered. This simulation system can display a perspective view of the PPF distribution, a transverse and a longitudinal section of the distribution, and a contour map of the distribution. Moreover, a contour map of the ratio of the value of the PPF emitted by blue LEDs to that by blue and red LEDs can be displayed. As the representation is achieved by colored lines according to the magnitudes of the PPF in our system, a user can understand and evaluate the state of the PPF well. PMID:11541576

  20. KAPPA DISTRIBUTION MODEL FOR HARD X-RAY CORONAL SOURCES OF SOLAR FLARES

    SciTech Connect

    Oka, M.; Ishikawa, S.; Saint-Hilaire, P.; Krucker, S.; Lin, R. P.

    2013-02-10

    Solar flares produce hard X-ray emission, the photon spectrum of which is often represented by a combination of thermal and power-law distributions. However, the estimates of the number and total energy of non-thermal electrons are sensitive to the determination of the power-law cutoff energy. Here, we revisit an 'above-the-loop' coronal source observed by RHESSI on 2007 December 31 and show that a kappa distribution model can also be used to fit its spectrum. Because the kappa distribution has a Maxwellian-like core in addition to a high-energy power-law tail, the emission measure and temperature of the instantaneous electrons can be derived without assuming the cutoff energy. Moreover, the non-thermal fractions of electron number/energy densities can be uniquely estimated because they are functions of only the power-law index. With the kappa distribution model, we estimated that the total electron density of the coronal source region was {approx}2.4 Multiplication-Sign 10{sup 10} cm{sup -3}. We also estimated without assuming the source volume that a moderate fraction ({approx}20%) of electrons in the source region was non-thermal and carried {approx}52% of the total electron energy. The temperature was 28 MK, and the power-law index {delta} of the electron density distribution was -4.3. These results are compared to the conventional power-law models with and without a thermal core component.

  1. Numerical evaluation of the jet noise source distribution from far-field cross correlations

    NASA Technical Reports Server (NTRS)

    Maestrello, L.; Liu, C.-H.

    1976-01-01

    This paper contains the development of techniques to determine the relationship between the unknown source correlation function to the correlation of scattered amplitudes in a jet. This study has application to the determination of forward motion effects. The technique has been developed and tested on a model jet of high subsonic flow. Numerical solution was obtained by solving the Fredholm integral equation of the first kind. Interpretation of the apparent source distribution and its application to flight testing are provided.

  2. Mismatched-basis statistics enable quantum key distribution with uncharacterized qubit sources

    NASA Astrophysics Data System (ADS)

    Yin, Zhen-Qiang; Fung, Chi-Hang Fred; Ma, Xiongfeng; Zhang, Chun-Mei; Li, Hong-Wei; Chen, Wei; Wang, Shuang; Guo, Guang-Can; Han, Zheng-Fu

    2014-11-01

    In the postprocessing of quantum key distribution, the raw key bits from the mismatched-basis measurements, where two parties use different bases, are normally discarded. Here, we propose a postprocessing method that exploits measurement statistics from mismatched-basis cases and prove that incorporating these statistics enables uncharacterized qubit sources to be used in the measurement-device-independent quantum key distribution protocol and the Bennett-Brassard 1984 protocol, which is otherwise impossible.

  3. Established and potential physiological roles of bicarbonate-sensing soluble adenylyl cyclase (sAC) in aquatic animals.

    PubMed

    Tresguerres, Martin; Barott, Katie L; Barron, Megan E; Roa, Jinae N

    2014-03-01

    Soluble adenylyl cyclase (sAC) is a recently recognized source of the signaling molecule cyclic AMP (cAMP) that is genetically and biochemically distinct from the classic G-protein-regulated transmembrane adenylyl cyclases (tmACs). Mammalian sAC is distributed throughout the cytoplasm and it may be present in the nucleus and inside mitochondria. sAC activity is directly stimulated by HCO3(-), and sAC has been confirmed to be a HCO3(-) sensor in a variety of mammalian cell types. In addition, sAC can functionally associate with carbonic anhydrases to act as a de facto sensor of pH and CO2. The two catalytic domains of sAC are related to HCO3(-)-regulated adenylyl cyclases from cyanobacteria, suggesting the cAMP pathway is an evolutionarily conserved mechanism for sensing CO2 levels and/or acid/base conditions. Reports of sAC in aquatic animals are still limited but are rapidly accumulating. In shark gills, sAC senses blood alkalosis and triggers compensatory H(+) absorption. In the intestine of bony fishes, sAC modulates NaCl and water absorption. And in sea urchin sperm, sAC may participate in the initiation of flagellar movement and in the acrosome reaction. Bioinformatics and RT-PCR results reveal that sAC orthologs are present in most animal phyla. This review summarizes the current knowledge on the physiological roles of sAC in aquatic animals and suggests additional functions in which sAC may be involved. PMID:24574382

  4. Established and potential physiological roles of bicarbonate-sensing soluble adenylyl cyclase (sAC) in aquatic animals

    PubMed Central

    Tresguerres, Martin; Barott, Katie L.; Barron, Megan E.; Roa, Jinae N.

    2014-01-01

    Soluble adenylyl cyclase (sAC) is a recently recognized source of the signaling molecule cyclic AMP (cAMP) that is genetically and biochemically distinct from the classic G-protein-regulated transmembrane adenylyl cyclases (tmACs). Mammalian sAC is distributed throughout the cytoplasm and it may be present in the nucleus and inside mitochondria. sAC activity is directly stimulated by HCO3−, and sAC has been confirmed to be a HCO3− sensor in a variety of mammalian cell types. In addition, sAC can functionally associate with carbonic anhydrases to act as a de facto sensor of pH and CO2. The two catalytic domains of sAC are related to HCO3−-regulated adenylyl cyclases from cyanobacteria, suggesting the cAMP pathway is an evolutionarily conserved mechanism for sensing CO2 levels and/or acid/base conditions. Reports of sAC in aquatic animals are still limited but are rapidly accumulating. In shark gills, sAC senses blood alkalosis and triggers compensatory H+ absorption. In the intestine of bony fishes, sAC modulates NaCl and water absorption. And in sea urchin sperm, sAC may participate in the initiation of flagellar movement and in the acrosome reaction. Bioinformatics and RT-PCR results reveal that sAC orthologs are present in most animal phyla. This review summarizes the current knowledge on the physiological roles of sAC in aquatic animals and suggests additional functions in which sAC may be involved. PMID:24574382

  5. X-ray point source distribution in the Galactic center region

    NASA Astrophysics Data System (ADS)

    Hong, J.; Grindlay, J.; Laycock, S.; Schlegel, E. M.; Zhao, P.

    2003-12-01

    Recent deep (520 ksec) Chandra observations on the Sgr A* by Muno et al. (2003, ApJ, 589, 225) discovered a significant population of hard X-ray (2-8 keV) sources strongly peaked around Sgr A*, falling off as 1/theta from the center. Preliminary analysis by Hong et al (2003, HEAD, 35, 1402) compared their spatial distribution with that of relatively shallow (2 x 12 ksec observation per field) and wide field (2 deg x 0.5 deg) observations around the Galactic center by Wang et al (2002, Nature, 415, 148). As a part of our on-going Chandra Multiwavelength Plane (ChaMPlane) Survey project to determine the accretion source content of the Galaxy, we (re)-analyzed all the available Chandra observations on the Galactic center region using Chandra analysis tools developed for ChaMPLane (Hong et al 2003). This analysis includes the Wang fields as well as archival data of a deep (100 ksec) Chandra observation of Sgr B2 (Takagi et al. 2002, ApJ, 573, 275) and other moderately deep (50 ksec) fields within 2 deg of the Galactic center. We derive logN-logS source distributions in the separate fields for a preliminary analysis of the overall source distribution in the central bulge. This is compared with the source distributions in our deep survey of Baade's Window (cf. Grindlay et al and Laycock et al; this meeting) for an initial estimate of the large scale point source distribution in the Bulge. This work is supported by NASA grants AR2-3002A and GO3-4033A.

  6. Source Distributions of Substorm Ions Observed in the Near-Earth Magnetotail

    NASA Technical Reports Server (NTRS)

    Ashour-Abdalla, M.; El-Alaoui, M.; Peroomian, V.; Walker, R. J.; Raeder, J.; Frank, L. A.; Paterson, W. R.

    1999-01-01

    This study employs Geotail plasma observations and numerical modeling to determine sources of the ions observed in the near-Earth magnetotail near midnight during a substorm. The growth phase has the low-latitude boundary layer as its most important source of ions at Geotail, but during the expansion phase the plasma mantle is dominant. The mantle distribution shows evidence of two distinct entry mechanisms: entry through a high latitude reconnection region resulting in an accelerated component, and entry through open field lines traditionally identified with the mantle source. The two entry mechanisms are separated in time, with the high-latitude reconnection region disappearing prior to substorm onset.

  7. Detailed dose distribution prediction of Cf-252 brachytherapy source with boron loading dose enhancement.

    PubMed

    Ghassoun, J; Mostacci, D; Molinari, V; Jehouani, A

    2010-02-01

    The purpose of this work is to evaluate the dose rate distribution and to determine the boron effect on dose rate distribution for (252)Cf brachytherapy source. This study was carried out using a Monte Carlo simulation. To validate the Monte Carlo computer code, the dosimetric parameters were determined following the updated TG-43 formalism and compared with current literature data. The validated computer code was then applied to evaluate the neutron and photon dose distribution and to illustrate the boron loading effect. PMID:19889549

  8. Distribution functions in plasmas generated by a volume source of fission fragments. [in nuclear pumped lasers

    NASA Technical Reports Server (NTRS)

    Deese, J. E.; Hassan, H. A.

    1979-01-01

    The role played by fission fragments and electron distribution functions in nuclear pumped lasers is considered and procedures for their calculations are outlined. The calculations are illustrated for a He-3/Xe mixture where fission is provided by the He-3(n,p)H-3 reaction. Because the dominant ion in the system depends on the Xe fraction, the distribution functions cannot be determined without the simultaneous consideration of a detailed kinetic model. As is the case for wall sources of fission fragments, the resulting plasmas are essentially thermal but the electron distribution functions are non-Maxwellian.

  9. Impact of the differential fluence distribution of brachytherapy sources on the spectroscopic dose-rate constant

    SciTech Connect

    Malin, Martha J.; Bartol, Laura J.; DeWerd, Larry A. E-mail: ladewerd@wisc.edu

    2015-05-15

    Purpose: To investigate why dose-rate constants for {sup 125}I and {sup 103}Pd seeds computed using the spectroscopic technique, Λ{sub spec}, differ from those computed with standard Monte Carlo (MC) techniques. A potential cause of these discrepancies is the spectroscopic technique’s use of approximations of the true fluence distribution leaving the source, φ{sub full}. In particular, the fluence distribution used in the spectroscopic technique, φ{sub spec}, approximates the spatial, angular, and energy distributions of φ{sub full}. This work quantified the extent to which each of these approximations affects the accuracy of Λ{sub spec}. Additionally, this study investigated how the simplified water-only model used in the spectroscopic technique impacts the accuracy of Λ{sub spec}. Methods: Dose-rate constants as described in the AAPM TG-43U1 report, Λ{sub full}, were computed with MC simulations using the full source geometry for each of 14 different {sup 125}I and 6 different {sup 103}Pd source models. In addition, the spectrum emitted along the perpendicular bisector of each source was simulated in vacuum using the full source model and used to compute Λ{sub spec}. Λ{sub spec} was compared to Λ{sub full} to verify the discrepancy reported by Rodriguez and Rogers. Using MC simulations, a phase space of the fluence leaving the encapsulation of each full source model was created. The spatial and angular distributions of φ{sub full} were extracted from the phase spaces and were qualitatively compared to those used by φ{sub spec}. Additionally, each phase space was modified to reflect one of the approximated distributions (spatial, angular, or energy) used by φ{sub spec}. The dose-rate constant resulting from using approximated distribution i, Λ{sub approx,i}, was computed using the modified phase space and compared to Λ{sub full}. For each source, this process was repeated for each approximation in order to determine which approximations used in

  10. DISTRIBUTION, TYPE, ACCUMULATION AND SOURCE OF MARINE DEBRIS IN THE UNITED STATES, 1989-93

    EPA Science Inventory

    Distribution, type, accumulation, & source of marine debris on coastal beaches and in harbors of the United States were examined from 1989 to 1993. nformation was compiled from annual beach cleanups coordinated by the Center for marine Conservation, quarterly beach surveys at eig...

  11. Bacterial Composition in a Metropolitan Drinking Water Distribution System Utilizing Different Source Waters

    EPA Science Inventory

    The microbial community structure was investigated from bulk phase water samples of multiple collection sites from two service areas within the Cincinnati drinking water distribution system (DWDS). Each area is associated with a different primary source of water (i.e., groundwat...

  12. 30 CFR 872.12 - Where do moneys distributed from the Fund and other sources go?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Where do moneys distributed from the Fund and other sources go? 872.12 Section 872.12 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR ABANDONED MINE LAND RECLAMATION MONEYS AVAILABLE TO ELIGIBLE...

  13. 30 CFR 872.12 - Where do moneys distributed from the Fund and other sources go?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Where do moneys distributed from the Fund and other sources go? 872.12 Section 872.12 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR ABANDONED MINE LAND RECLAMATION MONEYS AVAILABLE TO ELIGIBLE...

  14. MICROBIOLOGICAL CHANGES IN SOURCE WATER TREATMENT: REFLECTIONS IN DISTRIBUTION WATER QUALITY

    EPA Science Inventory

    Microbial quality in the distribution system is a reflection of raw source water characteristics, treatment process configurations and their modifications. ased on case history experiences there may at times be a microbial breakthrough that is caused by fluctuations in raw surfac...

  15. GIS Based Distributed Runoff Predictions in Variable Source Area Watersheds Employing the SCS-Curve Number

    NASA Astrophysics Data System (ADS)

    Steenhuis, T. S.; Mendoza, G.; Lyon, S. W.; Gerard Marchant, P.; Walter, M. T.; Schneiderman, E.

    2003-04-01

    Because the traditional Soil Conservation Service Curve Number (SCS-CN) approach continues to be ubiquitously used in GIS-BASED water quality models, new application methods are needed that are consistent with variable source area (VSA) hydrological processes in the landscape. We developed within an integrated GIS modeling environment a distributed approach for applying the traditional SCS-CN equation to watersheds where VSA hydrology is a dominant process. Spatial representation of hydrologic processes is important for watershed planning because restricting potentially polluting activities from runoff source areas is fundamental to controlling non-point source pollution. The methodology presented here uses the traditional SCS-CN method to predict runoff volume and spatial extent of saturated areas and uses a topographic index to distribute runoff source areas through watersheds. The resulting distributed CN-VSA method was incorporated in an existing GWLF water quality model and applied to sub-watersheds of the Delaware basin in the Catskill Mountains region of New York State. We found that the distributed CN-VSA approach provided a physically-based method that gives realistic results for watersheds with VSA hydrology.

  16. [Soil Heavy Metal Spatial Distribution and Source Analysis Around an Aluminum Plant in Baotou].

    PubMed

    Zhang, Lian-ke; Li, Hai-peng; Huang, Xue-min; Li, Yu-mei; Jiao, Kun-ling; Sun, Peng; Wang, Wei-da

    2016-03-15

    The soil with 500 m distance from an aluminum plant in Baotou was studied. A total of 64 soil samples were taken from the 0-5 cm, 5-20 cm, 20-40 cm and 40-60 cm layers, and the contents of Cu, Pb, Zn, Cr, Cd, Ni and Mn were tested, respectively. The correlation analysis and principal component analysis were used to identify the sources of these heavy metals in soils. The results suggested that the contents of Cu, Pb, Zn, Cr, Cd, Ni and Mn in study area were 32.9, 50.35, 69.92, 43.78, 0.54, 554.42 and 36.65 mg · kg⁻¹ respectively. All seven heavy metals tested were overweight compared with the background values of soil in Inner Mongolia. The spatial distribution of heavy metals showed that the horizontal distribution of heavy metals was obviously enriched in the southwest, while in vertical distribution, the heavy metal content (0 to 5 cm) was highest in the surface soil, and the heavy metal content decreased with increasing depth and tended to be stabilized when the depth was over 20 cm. Source analysis showed that the source of Cu, Zn, Cr and Mn might be influenced by the aluminum plant and the surrounding industrial activity. The source of Pb and Cd might be mainly related to road transportation. The source of Ni may be affected by agricultural activities and soil parent material together. PMID:27337911

  17. Operation Method for AC Motor Control during Power Interruption in Direct AC/AC Converter System

    NASA Astrophysics Data System (ADS)

    Shizu, Keiichiro; Azuma, Satoshi

    Direct AC/AC converters have been studied due to their potential use in power converters with no DC-link capacitor, which can contribute to the miniaturization of power converters. However, the absence of a DC-link capacitor makes it difficult to control the AC motor during power interruption. First, this paper proposes a system that realizes AC motor control during power interruption by utilizing a clamp capacitor. In general, direct AC/AC converters have a clamp circuit consisting of a rectifier diode(s) and a clamp capacitor in order to avoid over-voltages. In the proposed system, there is an additional semiconductor switch reverse-parallel to the rectifier diode(s), and the clamp capacitor voltage can be utilized for AC motor control by turning on the additional switch. Second, this paper discusses an operation method for AC motor control and clamp capacitor voltage control during power interruption. In the proposed method “DC-link voltage control”, the kinetic energy in the AC motor is transformed into electrical energy and stored in the clamp capacitor; the clamp capacitor is therefore charged and the capacitor voltage is controlled to remain constant at an instruction value. Third, this paper discusses a switching operation during power interruption. A dead-time is introduced between the operation of turning off all switches on the rectifier side and the operation of turning on the additional switch, which prevents the occurrence of a short circuit between the interrupted power source and the clamp capacitor. Finally, experimental results are presented. During power interruptions, an output current was continuously obtained and the clamp capacitor voltage was maintained to be equal to the instruction value of the capacitor voltage. These results indicate that both AC motor control and capacitor voltage control were successfully achieved by using the proposed system.

  18. Calculation of the neutron source distribution in the VENUS PWR Mockup Experiment

    SciTech Connect

    Williams, M.L.; Morakinyo, P.; Kam, F.B.K.; Leenders, L.; Minsart, G.; Fabry, A.

    1984-01-01

    The VENUS PWR Mockup Experiment is an important component of the Nuclear Regulatory Commission's program goal of benchmarking reactor pressure vessel (RPV) fluence calculations in order to determine the accuracy to which RPV fluence can be computed. Of particular concern in this experiment is the accuracy of the source calculation near the core-baffle interface, which is the important region for contributing to RPV fluence. Results indicate that the calculated neutron source distribution within the VENUS core agrees with the experimental measured values with an average error of less than 3%, except at the baffle corner, where the error is about 6%. Better agreement with the measured fission distribution was obtained with a detailed space-dependent cross-section weighting procedure for thermal cross sections near the core-baffle interface region. The maximum error introduced into the predicted RPV fluence due to source errors should be on the order of 5%.

  19. FDTD verification of deep-set brain tumor hyperthermia using a spherical microwave source distribution

    SciTech Connect

    Dunn, D.; Rappaport, C.M.; Terzuoli, A.J. Jr.

    1996-10-01

    Although use of noninvasive microwave hyperthermia to treat cancer is problematic in many human body structures, careful selection of the source electric field distribution around the entire surface of the head can generate a tightly focused global power density maximum at the deepest point within the brain. An analytic prediction of the optimum volume field distribution in a layered concentric head model based on summing spherical harmonic modes is derived and presented. This ideal distribution is then verified using a three-dimensional finite difference time domain (TDTD) simulation with a discretized, MRI-based head model excited by the spherical source. The numerical computation gives a very similar dissipated power pattern as the analytic prediction. This study demonstrates that microwave hyperthermia can theoretically be a feasible cancer treatment modality for tumors in the head, providing a well-resolved hot-spot at depth without overheating any other healthy tissue.

  20. AC power systems handbook

    SciTech Connect

    Whitaker, J.

    1991-01-01

    Transient disturbances are what headaches are made of. Whatever you call them-spikes, surges, are power bumps-they can take your equipment down and leave you with a complicated and expensive repair job. Protection against transient disturbances is a science that demands attention to detail. This book explains how the power distribution system works, what can go wrong with it, and how to protect a facility against abnormalities. system grounding and shielding are covered in detail. Each major method of transient protection is analyzed and its relative merits discussed. The book provides a complete look at the critical elements of the ac power system. Provides a complete look at the ac power system from generation to consumption. Discusses the mechanisms that produce transient disturbances and how to protect against them. Presents diagrams to facilitate system design. Covers new areas, such as the extent of the transient disturbance problem, transient protection options, and stand-by power systems.

  1. Distributed Source Modeling of Language with Magnetoencephalography: Application to Patients with Intractable Epilepsy

    PubMed Central

    McDonald, Carrie R.; Thesen, Thomas; Hagler, Donald J.; Carlson, Chad; Devinksy, Orrin; Kuzniecky, Rubin; Barr, William; Gharapetian, Lusineh; Trongnetrpunya, Amy; Dale, Anders M.; Halgren, Eric

    2009-01-01

    Purpose To examine distributed patterns of language processing in healthy controls and patients with epilepsy using magnetoencephalography (MEG), and to evaluate the concordance between laterality of distributed MEG sources and language laterality as determined by the intracarotid amobarbitol procedure (IAP). Methods MEG was performed in ten healthy controls using an anatomically-constrained, noise-normalized distributed source solution (dSPM). Distributed source modeling of language was then applied to eight patients with intractable epilepsy. Average source strengths within temporoparietal and frontal lobe regions of interest (ROIs) were calculated and the laterality of activity within ROIs during discrete time windows was compared to results from the IAP. Results In healthy controls, dSPM revealed activity in visual cortex bilaterally from ~80-120ms in response to novel words and sensory control stimuli (i.e., false fonts). Activity then spread to fusiform cortex ~160-200ms, and was dominated by left hemisphere activity in response to novel words. From ~240-450ms, novel words produced activity that was left-lateralized in frontal and temporal lobe regions, including anterior and inferior temporal, temporal pole, and pars opercularis, as well as bilaterally in posterior superior temporal cortex. Analysis of patient data with dSPM demonstrated that from 350-450ms, laterality of temporoparietal sources agreed with the IAP 75% of the time, whereas laterality of frontal MEG sources agreed with the IAP in all eight patients. Discussion Our results reveal that dSPM can unveil the timing and spatial extent of language processes in patients with epilepsy and may enhance knowledge of language lateralization and localization for use in preoperative planning. PMID:19552656

  2. Effective petroleum source rocks of the world: Stratigraphic distribution and controlling depositional factors

    SciTech Connect

    Klemme, H.D. ); Ulmishek, G.F. )

    1991-12-01

    Six stratigraphic intervals, representing one-third of Phanerozoic time, contain petroleum source rocks that have provided more than 90% of the world's discovered original reserves of oil and gas (in barrels of oil equivalent). The six intervals are (1) Silurian (generated 9% of the world's reserves), (2) Upper Devonian-Tournaisian (8% of reserves), (3) Pennsylvanian-Lower Permian (8% of reserves), (4) Upper Jurassic (25% of reserves), (5) middle Cretaceous (29% of reserves), and (6) Oligocene-Miocene (12.5% of reserves). This uneven distribution of source rocks vary from interval to interval. Maps that show facies, structural forms, and petroleum source rocks were prepared for this study. Analysis of the maps indicates that several primary factors controlled the areal distribution of source rocks, their geochemical type, and their effectiveness (i.e., the amounts of discovered original conventionally recoverable reserves of oil and gas generated by these rocks). These factors are geologic age, paleolatitude of the depositional areas, structural forms in which the deposition of source rocks occurred, and the evolution of biota. The maturation time of these source rocks demonstrates that majority of discovered oil and gas is very young; almost 70% of the world's original reserves of oil and gas has been generated since the Coniacian, and nearly 50% of the world's petroleum{sup 4} has been generated and trapped since the Oligocene.

  3. Microlensing towards the LMC revisited by adopting a non-Gaussian velocity distribution for the sources

    NASA Astrophysics Data System (ADS)

    Mancini, L.

    2009-03-01

    Aims: We discuss whether the Gaussian is a reasonable approximation of the velocity distribution of stellar systems that are not spherically distributed. Methods: By using a non-Gaussian velocity distribution to describe the sources in the Large Magellanic Cloud (LMC), we reinvestigate the expected microlensing parameters of a lens population isotropically distributed either in the Milky Way halo or in the LMC (self lensing). We compare our estimates with the experimental results of the MACHO collaboration. Results: An interesting result that emerges from our analysis is that, moving from the Gaussian to the non-Gaussian case, we do not observe any change in the form of the distribution curves describing the rate of microlensing events for lenses in the Galactic halo. The corresponding expected timescales and number of expected events also do not vary. Conversely, with respect to the self-lensing case, we observe a moderate increase in the rate and number of expected events. We conclude that the error in the estimate of the most likely value for the MACHO mass and the Galactic halo fraction in form of MACHOs, calculated with a Gaussian velocity distribution for the LMC sources, is not higher than 2%.

  4. Wearable Sensor Localization Considering Mixed Distributed Sources in Health Monitoring Systems

    PubMed Central

    Wan, Liangtian; Han, Guangjie; Wang, Hao; Shu, Lei; Feng, Nanxing; Peng, Bao

    2016-01-01

    In health monitoring systems, the base station (BS) and the wearable sensors communicate with each other to construct a virtual multiple input and multiple output (VMIMO) system. In real applications, the signal that the BS received is a distributed source because of the scattering, reflection, diffraction and refraction in the propagation path. In this paper, a 2D direction-of-arrival (DOA) estimation algorithm for incoherently-distributed (ID) and coherently-distributed (CD) sources is proposed based on multiple VMIMO systems. ID and CD sources are separated through the second-order blind identification (SOBI) algorithm. The traditional estimating signal parameters via the rotational invariance technique (ESPRIT)-based algorithm is valid only for one-dimensional (1D) DOA estimation for the ID source. By constructing the signal subspace, two rotational invariant relationships are constructed. Then, we extend the ESPRIT to estimate 2D DOAs for ID sources. For DOA estimation of CD sources, two rational invariance relationships are constructed based on the application of generalized steering vectors (GSVs). Then, the ESPRIT-based algorithm is used for estimating the eigenvalues of two rational invariance matrices, which contain the angular parameters. The expressions of azimuth and elevation for ID and CD sources have closed forms, which means that the spectrum peak searching is avoided. Therefore, compared to the traditional 2D DOA estimation algorithms, the proposed algorithm imposes significantly low computational complexity. The intersecting point of two rays, which come from two different directions measured by two uniform rectangle arrays (URA), can be regarded as the location of the biosensor (wearable sensor). Three BSs adopting the smart antenna (SA) technique cooperate with each other to locate the wearable sensors using the angulation positioning method. Simulation results demonstrate the effectiveness of the proposed algorithm. PMID:26985896

  5. Wearable Sensor Localization Considering Mixed Distributed Sources in Health Monitoring Systems.

    PubMed

    Wan, Liangtian; Han, Guangjie; Wang, Hao; Shu, Lei; Feng, Nanxing; Peng, Bao

    2016-01-01

    In health monitoring systems, the base station (BS) and the wearable sensors communicate with each other to construct a virtual multiple input and multiple output (VMIMO) system. In real applications, the signal that the BS received is a distributed source because of the scattering, reflection, diffraction and refraction in the propagation path. In this paper, a 2D direction-of-arrival (DOA) estimation algorithm for incoherently-distributed (ID) and coherently-distributed (CD) sources is proposed based on multiple VMIMO systems. ID and CD sources are separated through the second-order blind identification (SOBI) algorithm. The traditional estimating signal parameters via the rotational invariance technique (ESPRIT)-based algorithm is valid only for one-dimensional (1D) DOA estimation for the ID source. By constructing the signal subspace, two rotational invariant relationships are constructed. Then, we extend the ESPRIT to estimate 2D DOAs for ID sources. For DOA estimation of CD sources, two rational invariance relationships are constructed based on the application of generalized steering vectors (GSVs). Then, the ESPRIT-based algorithm is used for estimating the eigenvalues of two rational invariance matrices, which contain the angular parameters. The expressions of azimuth and elevation for ID and CD sources have closed forms, which means that the spectrum peak searching is avoided. Therefore, compared to the traditional 2D DOA estimation algorithms, the proposed algorithm imposes significantly low computational complexity. The intersecting point of two rays, which come from two different directions measured by two uniform rectangle arrays (URA), can be regarded as the location of the biosensor (wearable sensor). Three BSs adopting the smart antenna (SA) technique cooperate with each other to locate the wearable sensors using the angulation positioning method. Simulation results demonstrate the effectiveness of the proposed algorithm. PMID:26985896

  6. RADIAL DISTRIBUTION OF X-RAY POINT SOURCES NEAR THE GALACTIC CENTER

    SciTech Connect

    Hong, Jae Sub; Van den Berg, Maureen; Grindlay, Jonathan E.; Laycock, Silas

    2009-11-20

    We present the log N-log S and spatial distributions of X-ray point sources in seven Galactic bulge (GB) fields within 4 deg. from the Galactic center (GC). We compare the properties of 1159 X-ray point sources discovered in our deep (100 ks) Chandra observations of three low extinction Window fields near the GC with the X-ray sources in the other GB fields centered around Sgr B2, Sgr C, the Arches Cluster, and Sgr A* using Chandra archival data. To reduce the systematic errors induced by the uncertain X-ray spectra of the sources coupled with field-and-distance-dependent extinction, we classify the X-ray sources using quantile analysis and estimate their fluxes accordingly. The result indicates that the GB X-ray population is highly concentrated at the center, more heavily than the stellar distribution models. It extends out to more than 1.{sup 0}4 from the GC, and the projected density follows an empirical radial relation inversely proportional to the offset from the GC. We also compare the total X-ray and infrared surface brightness using the Chandra and Spitzer observations of the regions. The radial distribution of the total infrared surface brightness from the 3.6 band mum images appears to resemble the radial distribution of the X-ray point sources better than that predicted by the stellar distribution models. Assuming a simple power-law model for the X-ray spectra, the closer to the GC the intrinsically harder the X-ray spectra appear, but adding an iron emission line at 6.7 keV in the model allows the spectra of the GB X-ray sources to be largely consistent across the region. This implies that the majority of these GB X-ray sources can be of the same or similar type. Their X-ray luminosity and spectral properties support the idea that the most likely candidate is magnetic cataclysmic variables (CVs), primarily intermediate polars (IPs). Their observed number density is also consistent with the majority being IPs, provided the relative CV to star density in

  7. Ac traction gets on track

    SciTech Connect

    O`Connor, L.

    1995-09-01

    This article describes inverter-based ac traction systems which give freight locomotives greater adhesion, pulling power, and braking capacity. In the 1940s, dc traction replaced the steam engine as a source of train propulsion, and it has ruled the freight transportation industry ever since. But now, high-performance ac-traction systems, with their unprecedented levels of pulling power and adhesion, are becoming increasingly common on America`s freight railroads. In thousands of miles of demonstration tests, today`s ac-traction systems have outperformed traditional dc-motor driven systems. Major railroad companies are convinced enough of the benefits of ac traction to have integrated it into their freight locomotives.

  8. Multi-Sensor Integration to Map Odor Distribution for the Detection of Chemical Sources

    PubMed Central

    Gao, Xiang; Acar, Levent

    2016-01-01

    This paper addresses the problem of mapping odor distribution derived from a chemical source using multi-sensor integration and reasoning system design. Odor localization is the problem of finding the source of an odor or other volatile chemical. Most localization methods require a mobile vehicle to follow an odor plume along its entire path, which is time consuming and may be especially difficult in a cluttered environment. To solve both of the above challenges, this paper proposes a novel algorithm that combines data from odor and anemometer sensors, and combine sensors’ data at different positions. Initially, a multi-sensor integration method, together with the path of airflow was used to map the pattern of odor particle movement. Then, more sensors are introduced at specific regions to determine the probable location of the odor source. Finally, the results of odor source location simulation and a real experiment are presented. PMID:27384568

  9. Shared and Distributed Memory Parallel Security Analysis of Large-Scale Source Code and Binary Applications

    SciTech Connect

    Quinlan, D; Barany, G; Panas, T

    2007-08-30

    Many forms of security analysis on large scale applications can be substantially automated but the size and complexity can exceed the time and memory available on conventional desktop computers. Most commercial tools are understandably focused on such conventional desktop resources. This paper presents research work on the parallelization of security analysis of both source code and binaries within our Compass tool, which is implemented using the ROSE source-to-source open compiler infrastructure. We have focused on both shared and distributed memory parallelization of the evaluation of rules implemented as checkers for a wide range of secure programming rules, applicable to desktop machines, networks of workstations and dedicated clusters. While Compass as a tool focuses on source code analysis and reports violations of an extensible set of rules, the binary analysis work uses the exact same infrastructure but is less well developed into an equivalent final tool.

  10. Multi-Sensor Integration to Map Odor Distribution for the Detection of Chemical Sources.

    PubMed

    Gao, Xiang; Acar, Levent

    2016-01-01

    This paper addresses the problem of mapping odor distribution derived from a chemical source using multi-sensor integration and reasoning system design. Odor localization is the problem of finding the source of an odor or other volatile chemical. Most localization methods require a mobile vehicle to follow an odor plume along its entire path, which is time consuming and may be especially difficult in a cluttered environment. To solve both of the above challenges, this paper proposes a novel algorithm that combines data from odor and anemometer sensors, and combine sensors' data at different positions. Initially, a multi-sensor integration method, together with the path of airflow was used to map the pattern of odor particle movement. Then, more sensors are introduced at specific regions to determine the probable location of the odor source. Finally, the results of odor source location simulation and a real experiment are presented. PMID:27384568

  11. Evaluating the effect of network density and geometric distribution on kinematic source inversion models

    NASA Astrophysics Data System (ADS)

    Zhang, Youbing; Song, Seok Goo; Dalguer, Luis; Clinton, John

    2013-04-01

    An essential element of understanding earthquake source processes is obtaining a reliable source model via geophysical data inversion. The most common procedure to determine the kinematic source parameters (final slip, peak slip velocity, rise time and rupture time) is to invert observed ground motions recorded at a number of different stations (typically strong motion accelerometers). Few studies have been dedicated to evaluate the effect of the number of stations and their geometrical distribution on earthquake source parameters. In this paper we investigate these effects by inverting ground motions from synthetic dynamic earthquake rupture models with heterogeneous stress distribution governed by the slip weakening friction law. Our first target model is a buried strike-slip event (Mw 6.5) in a layered half space. The Compsyn code (Spudich and Xu, 2002) was used in the inversion procedure to generate forward synthetic waveforms, and an Evolutionary Algorithm was used to search for the source parameters: peak slip velocity (PSV), rupture time, and rise time at low frequency (up to 1Hz). The regularized Yoffe function was applied as a single window slip velocity function, which is a flexible slip velocity function defined by three independent parameters: the final slip, the slip duration and the duration of the positive slip acceleration, Tacc (Tinti, et al. 2005). The same velocity structure was used for both the foward and inversion modeling and no noise was added to the synthetic ground motions before inversion. We applied the Tikhonov regularization to smooth the final slip on fault, which is controlled by PSV and rise time. Our preliminary results show that: First, we can capture large slip patches of the dynamic models with good ground velocity waveform fitting, using the regularized Yoffe function, which is consistent with the overall properties of dynamic rupture models. Second, the geometry of station distribution is important for finite kinematic source

  12. Estimating the Distribution of Noise Sources in Ambient Noise Derived Green’s Functions

    NASA Astrophysics Data System (ADS)

    Harmon, N.; Gerstoft, P.; Rychert, C. A.

    2009-12-01

    Estimation of surface wave Green’s functions from ambient seismic noise cross correlation requires an accurate model of the source distribution. We compare and contrast the results from three different methods for estimating the distribution of sources using vertical component data from the 190 stations of the Southern California Seismic Network for 1 year of data (2008). The methods include: 1) stacked beamformer output of short time period noise cross correlations, 2) a least-squares inversion of year long stacked noise correlation functions (NCF) assuming a 2-dimensional plane wave source density model, and 3) a least-squares inversion of NCF assuming a 3-dimensional plane wave source density model. The beamforming method and 3D plane wave source density model both indicate a strong surface wave component in the NCF, with weaker signals from near vertical incidence body waves. All three methods recover similar azimuthal surface wave source density functions, with maxima in the density functions between the methods within ±4° azimuth in the 7-25 s period range. Although there is a difference in the power between the beamforming method and the 2D and 3D plane wave inversions. This is expected as the peak from beamforming on several stations tends to be narrower than the two stations used in cross-correlations. Using the 2D and 3D distribution of plane wave models, we demonstrate how phase corrections for non-homogenous sources can be calculated to improve the accuracy of ambient noise tomographic studies. We also estimate that without correcting for the source effect, the isotropic phase velocity estimate is < 1% different from the observed teleseismic velocity estimates, but that there is up to a 1-3% peak-to-peak azimuthal variation in phase velocity predicted by these source distribution models which could be mapped into azimuthal anisotropy at 7-25 s period. Furthermore, sampling bias in station-to-station distance and azimuth could lead to spurious

  13. Statistical Measurement of the Gamma-Ray Source-count Distribution as a Function of Energy

    NASA Astrophysics Data System (ADS)

    Zechlin, Hannes-S.; Cuoco, Alessandro; Donato, Fiorenza; Fornengo, Nicolao; Regis, Marco

    2016-08-01

    Statistical properties of photon count maps have recently been proven as a new tool to study the composition of the gamma-ray sky with high precision. We employ the 1-point probability distribution function of six years of Fermi-LAT data to measure the source-count distribution dN/dS and the diffuse components of the high-latitude gamma-ray sky as a function of energy. To that aim, we analyze the gamma-ray emission in five adjacent energy bands between 1 and 171 GeV. It is demonstrated that the source-count distribution as a function of flux is compatible with a broken power law up to energies of ˜50 GeV. The index below the break is between 1.95 and 2.0. For higher energies, a simple power-law fits the data, with an index of {2.2}-0.3+0.7 in the energy band between 50 and 171 GeV. Upper limits on further possible breaks as well as the angular power of unresolved sources are derived. We find that point-source populations probed by this method can explain {83}-13+7% ({81}-19+52%) of the extragalactic gamma-ray background between 1.04 and 1.99 GeV (50 and 171 GeV). The method has excellent capabilities for constraining the gamma-ray luminosity function and the spectra of unresolved blazars.

  14. The Red MSX Source survey: distribution and properties of a sample of massive young stars

    NASA Astrophysics Data System (ADS)

    Urquhart, J. S.; Moore, T. J. T.; Hoare, M. G.; Lumsden, S. L.; Oudmaijer, R. D.; Rathborne, J. M.; Mottram, J. C.; Davies, B.; Stead, J. J.

    2011-01-01

    The Red MSX Source (RMS) survey has identified a large sample of massive young stellar objects and ultra compact H II regions from a sample of ˜2000 MSX and Two Micron All Sky Survey (2MASS) colour selected sources. Using a recent catalogue of molecular clouds derived from the Boston University-Five College Radio Astronomy Observatory (BU-FCRAO) Galactic Ring Survey (GRS), and by applying a Galactic scaleheight cut-off of 120 pc, we solve the distance ambiguity for RMS sources located within 18°<|l|> 54°. These two steps yield kinematic distances to 291 sources out of a possible 326, located within the GRS longitude range. Combining distances and integrated fluxes derived from spectral energy distributions, we estimate luminosities to these sources and find that >90 per cent are indicative of the presence of a massive star. We find the completeness limit of our sample is ˜104 L⊙, which corresponds to a zero-age main-sequence star with a mass of ˜12 M⊙. Selecting only these sources, we construct a complete sample of 196 sources. Comparing the properties of the sample of young massive stars with the general population, we find the RMS clouds are generally larger, more massive, and more turbulent. We examine the distribution of this subsample with respect to the location of the spiral arms and the Galactic bar and find them to be spatially correlated. We identify three significant peaks in the source surface density at Galactocentric radii of approximately 4, 6 and 8 kpc, which correspond to the proposed positions of the Scutum, Sagittarius and Perseus spiral arms, respectively. Fitting a scaleheight to the data we obtain an average value of ˜29 ± 0.5 pc, which agrees well with other reported values in the literature, however we note a dependence of the scaleheight on galactocentric radius with it increases from 30 to 45 pc between 2.5 and 8.5 kpc.

  15. Analysis of the relationship between landslides size distribution and earthquake source area

    NASA Astrophysics Data System (ADS)

    Valagussa, Andrea; Crosta, Giovanni B.; Frattini, Paolo; Xu, Chong

    2014-05-01

    The spatial distribution of earthquake induced landslides around the seismogenetic source has been analysed to better understand the triggering of landslides in seismic areas and to forecast the maximum distance at which an earthquake, with a certain magnitude, can induce landslides (e.g Keefer, 1984). However, when applying such approaches to old earthquakes (e.g 1929 Buller and 1968 Iningahua earthquakes New Zealand; Parker, 2013; 1976 Friuli earthquake, Italy) one should be concerned about the undersampling of smaller landslides which can be cancelled by erosion and landscape evolution. For this reason, it is important to characterize carefully the relationship between landslide area and number with distance from the source, but also the size distribution of landslides as a function of distance from the source. In this paper, we analyse the 2008 Wenchuan earthquake landslide inventory (Xu et al, 2013). The earthquake triggered more than 197,000 landslides of different type, including rock avalanches, rockfalls, translational and rotational slides, lateral spreads and derbies flows. First, we calculated the landslide intensity (number of landslides per unit area) and spatial density (landslide area per unit area) as a function of distance from the source area of the earthquake. Then, we developed magnitude frequency curves (MFC) for different distances from the source area. Comparing these curves, we can describe the relation between the distance and the frequency density of landslide in seismic area. Keefer D K (1984) Landslides caused by earthquakes. Geological Society of America Bulletin, 95(4), 406-421. Parker R N, (2013) Hillslope memory and spatial and temporal distributions of earthquake-induced landslides, Durham theses, Durham University. Xu, C., Xu, X., Yao, X., & Dai, F. (2013). Three (nearly) complete inventories of landslides triggered by the May 12, 2008 Wenchuan Mw 7.9 earthquake of China and their spatial distribution statistical analysis

  16. A Monte Carlo study on dose distribution validation of GZP6 60Co stepping source

    PubMed Central

    Bahreyni Toossi, Mohammad Taghi; Abdollahi, Maliheh; Ghorbani, Mahdi

    2012-01-01

    Aim Stepping source in brachytherapy systems is used to treat a target lesion longer than the effective treatment length of the source. Cancerous lesions in the cervix, esophagus and rectum are examples of such a target lesion. Background In this study, the stepping source of a GZP6 afterloading intracavitary brachytherapy unit was simulated using Monte Carlo (MC) simulation and the results were used for the validation of the GZP6 treatment planning system (TPS). Materials and methods The stepping source was simulated using MCNPX Monte Carlo code. Dose distributions in the longitudinal plane were obtained by using a matrix shift method for esophageal tumor lengths of 8 and 10 cm. A mesh tally has been employed for the absorbed dose calculation in a cylindrical water phantom. A total of 5 × 108 photon histories were scored and the MC statistical error obtained was at the range of 0.008–3.5%, an average of 0.2%. Results The acquired MC and TPS isodose curves were compared and it was shown that the dose distributions in the longitudinal plane were relatively coincidental. In the transverse direction, a maximum dose difference of 7% and 5% was observed for tumor lengths of 8 and 10 cm, respectively. Conclusion Considering that the certified source activity is given with ±10% uncertainty, the obtained difference is reasonable. It can be concluded that the accuracy of the dose distributions produced by GZP6 TPS for the stepping source is acceptable for its clinical applications. PMID:24416537

  17. An efficient central DOA tracking algorithm for multiple incoherently distributed sources

    NASA Astrophysics Data System (ADS)

    Hassen, Sonia Ben; Samet, Abdelaziz

    2015-12-01

    In this paper, we develop a new tracking method for the direction of arrival (DOA) parameters assuming multiple incoherently distributed (ID) sources. The new approach is based on a simple covariance fitting optimization technique exploiting the central and noncentral moments of the source angular power densities to estimate the central DOAs. The current estimates are treated as measurements provided to the Kalman filter that model the dynamic property of directional changes for the moving sources. Then, the covariance-fitting-based algorithm and the Kalman filtering theory are combined to formulate an adaptive tracking algorithm. Our algorithm is compared to the fast approximated power iteration-total least square-estimation of signal parameters via rotational invariance technique (FAPI-TLS-ESPRIT) algorithm using the TLS-ESPRIT method and the subspace updating via FAPI-algorithm. It will be shown that the proposed algorithm offers an excellent DOA tracking performance and outperforms the FAPI-TLS-ESPRIT method especially at low signal-to-noise ratio (SNR) values. Moreover, the performances of the two methods increase as the SNR values increase. This increase is more prominent with the FAPI-TLS-ESPRIT method. However, their performances degrade when the number of sources increases. It will be also proved that our method depends on the form of the angular distribution function when tracking the central DOAs. Finally, it will be shown that the more the sources are spaced, the more the proposed method can exactly track the DOAs.

  18. Tsunami source parameters estimated from slip distribution and their relation to tsunami intensity

    NASA Astrophysics Data System (ADS)

    Bolshakova, Anna; Nosov, Mikhail; Kolesov, Sergey

    2015-04-01

    Estimation of the level of tsunami hazard on the basis of earthquake moment magnitude often fails. The most important reason for this is that tsunamis are related to earthquakes in a complex and ambiguous way. In order to reveal a measure of tsunamigenic potential of an earthquake that would be better than moment magnitude of earthquake we introduce a set of tsunami source parameters that can be calculated from co-seismic ocean-bottom deformation and bathymetry. We consider more than two hundred ocean-bottom earthquakes (1923-2014) those for which detailed slip distribution data (Finite Fault Model) are available on USGS, UCSB, Caltech, and eQuake-RC sites. Making use of the Okada formulae the vector fields of co-seismic deformation of ocean bottom are estimated from the slip distribution data. Taking into account bathymetry (GEBCO_08) we determine tsunami source parameters such as double amplitude of bottom deformation, displaced water volume, potential energy of initial elevation, etc. The tsunami source parameters are examined as a function of earthquake moment magnitude. The contribution of horisontal component of ocean bottom deformation to tsunami generation is investigated. We analyse the Soloviev-Imamura tsunami intensity as a function of tsunami source parameters. The possibility of usage of tsunami source parameters instead of moment magnitude in tsunami warning is discussed. This work was supported by the Russian Foundation for Basic Research, project 14-05-31295

  19. Occurrence, distribution and risk assessment of polychlorinated biphenyls and polybrominated diphenyl ethers in nine water sources.

    PubMed

    Yang, Yuyi; Xie, Qilai; Liu, Xinyu; Wang, Jun

    2015-05-01

    Water quality of water sources is a critical issue for human health in South China, which experiences rapid economic development and is the most densely populated region in China. In this study, the pollution of organohalogen compounds in nine important water sources, South China was investigated. Twenty six organohalogen compounds including seventeen polychlorinated biphenyls (PCBs) and nine polybrominated diphenyl ethers (PBDEs) were detected using gas chromatograph analysis. The concentrations of total PCBs ranged from 0.93 to 13.07ngL(-1), with an average value of 7.06ngL(-1). The total concentrations of nine PBDE congeners were found in range not detected (nd) to 7.87ngL(-1) with an average value of 2.59ngL(-1). Compositions of PCBs and PBDEs indicated the historical use of Aroclors 1248, 1254 and 1260, and commercial PBDEs may be the main source of organohalogen compounds in water sources in South China. The nine water sources could be classified into three clusters by self-organizing map neural network. Low halogenated PCBs and PBDEs showed similar distribution in the nine water sources. Cancer risks of PCBs and PBDEs via water consumption were all below 10(-6), indicating the water quality in the nine water sources, South China was safe for human drinking. PMID:25681605

  20. Security of two-way continuous-variable quantum key distribution with source noise

    NASA Astrophysics Data System (ADS)

    Wang, Tianyi; Yu, Song; Zhang, Yi-Chen; Gu, Wanyi; Guo, Hong

    2014-11-01

    We investigate the security of reverse reconciliation two-way continuous-variable quantum key distribution with source noise at both legitimate sides. Because the source noise originates from imperfect devices, we ascribe it to the legitimate sides rather than the eavesdropper. The trusted model consists of a thermal noise injected into a beam splitter. The expressions of secret key rate are derived against collective entangling cloner attacks for homodyne and heterodyne detections. Simulation results show that by applying the trusted model, the security bound of the reverse reconciliation two-way protocols can be tightened, while the advantage over one-way protocols still maintains.

  1. Bright integrated photon-pair source for practical passive decoy-state quantum key distribution

    NASA Astrophysics Data System (ADS)

    Krapick, S.; Stefszky, M. S.; Jachura, M.; Brecht, B.; Avenhaus, M.; Silberhorn, C.

    2014-01-01

    We report on a bright, nondegenerate type-I parametric down-conversion source, which is well suited for passive decoy-state quantum key distribution. We show the photon-number-resolved analysis over a broad range of pump powers and we prove heralded higher-order n-photon states up to n =4. The inferred photon click statistics exhibit excellent agreements to the theoretical predictions. From our measurement results we conclude that our source meets the requirements to avert photon-number-splitting attacks.

  2. Post-quantum attacks on key distribution schemes in the presence of weakly stochastic sources

    NASA Astrophysics Data System (ADS)

    Al–Safi, S. W.; Wilmott, C. M.

    2015-09-01

    It has been established that the security of quantum key distribution protocols can be severely compromised were one to permit an eavesdropper to possess a very limited knowledge of the random sources used between the communicating parties. While such knowledge should always be expected in realistic experimental conditions, the result itself opened a new line of research to fully account for real-world weak randomness threats to quantum cryptography. Here we expand of this novel idea by describing a key distribution scheme that is provably secure against general attacks by a post-quantum adversary. We then discuss possible security consequences for such schemes under the assumption of weak randomness.

  3. Source contributions to the size and composition distribution of urban particulate air pollution

    NASA Astrophysics Data System (ADS)

    Kleeman, Michael J.; Cass, Glen R.

    A mechanistic air quality model has been constructed which is capable of predicting the contribution of individual emissions source types to the size- and chemical-composition distribution of airborne particles. This model incorporates all of the major aerosol processes relevant to regional air pollution studies including emissions, transport, deposition, gas-to-particle conversion and fog chemistry. In addition, the aerosol is represented as a source-oriented external mixture which is allowed to age in a more realistic fashion than can be accomplished when fresh particle-phase emissions are averaged into the pre-existing atmospheric aerosol size and composition distribution. A source-oriented external mixture is created by differentiating the primary particles emitted from the following source types: catalyst-equipped gasoline engines, non-catalyst-equipped gasoline engines, diesel engines, meat cooking, paved road dust, crustal material from sources other than paved road dust, and sulfur-bearing particles from fuel burning and industrial processes. Discrete primary seed particles from each of these source types are emitted into a simulation of atmospheric transport and chemical reaction. The individual particles evolve over time in the presence of gas-to-particle conversion processes while retaining information on the initial source from which they were emitted. The source- and age-resolved particle mechanics model is applied to the 1987 August SCAQS episode and comparisons are made between model predictions and observations at Claremont, CA. The model explains the origin of the bimodal character of the sub-micron aerosol size distribution. The mode located between 0.2 and 0.3 μm particle diameter is shaped by transformed emissions from diesel engines and meat cooking operations with lesser contributions from gasolinepowered vehicles and other fuel burning. The larger mode located at 0.7-0.8 μm particle diameter is due to fine particle background aerosol that

  4. Passive-scheme analysis for solving the untrusted source problem in quantum key distribution

    NASA Astrophysics Data System (ADS)

    Peng, Xiang; Xu, Bingjie; Guo, Hong

    2010-04-01

    As a practical method, the passive scheme is useful to monitor the photon statistics of an untrusted source in a “Plug & Play” quantum key distribution (QKD) system. In a passive scheme, three kinds of monitor mode can be adopted: average photon number (APN) monitor, photon number analyzer (PNA), and photon number distribution (PND) monitor. In this paper, the security analysis is rigorously given for the APN monitor, while for the PNA, the analysis, including statistical fluctuation and random noise, is addressed with a confidence level. The results show that the PNA can achieve better performance than the APN monitor and can asymptotically approach the theoretical limit of the PND monitor. Also, the passive scheme with the PNA works efficiently when the signal-to-noise ratio (RSN) is not too low and so is highly applicable to solve the untrusted source problem in the QKD system.

  5. Electron energy distribution function by using probe method in electron cyclotron resonance multicharged ion source

    SciTech Connect

    Kumakura, Sho Kurisu, Yosuke; Kimura, Daiju; Yano, Keisuke; Imai, Youta; Sato, Fuminobu; Kato, Yushi; Iida, Toshiyuki

    2014-02-15

    We are constructing a tandem type electron cyclotron resonance (ECR) ion source (ECRIS). High-energy electrons in ECRIS plasma affect electron energy distribution and generate multicharged ion. In this study, we measure electron energy distribution function (EEDF) of low energy region (≦100 eV) in ECRIS plasma at extremely low pressures (10{sup −3}–10{sup −5} Pa) by using cylindrical Langmuir probe. From the result, it is found that the EEDF correlates with the electron density and the temperature from the conventional probe analysis. In addition, we confirm that the tail of EEDF spreads to high energy region as the pressure rises and that there are electrons with high energy in ECR multicharged ion source plasma. The effective temperature estimated from the experimentally obtained EEDF is larger than the electron temperature obtained from the conventional method.

  6. Theoretical and measured electric field distributions within an annular phased array: consideration of source antennas.

    PubMed

    Zhang, Y; Joines, W T; Jirtle, R L; Samulski, T V

    1993-08-01

    The magnitude of E-field patterns generated by an annular array prototype device has been calculated and measured. Two models were used to describe the radiating sources: a simple linear dipole and a stripline antenna model. The stripline model includes detailed geometry of the actual antennas used in the prototype and an estimate of the antenna current based on microstrip transmission line theory. This more detailed model yields better agreement with the measured field patterns, reducing the rms discrepancy by a factor of about 6 (from approximately 23 to 4%) in the central region of interest where the SEM is within 25% of the maximum. We conclude that accurate modeling of source current distributions is important for determining SEM distributions associated with such heating devices. PMID:8258444

  7. Auditory evoked off-response: its source distribution is different from that of on-response.

    PubMed

    Noda, K; Tonoike, M; Doi, K; Koizuka, I; Yamaguchi, M; Seo, R; Matsumoto, N; Noiri, T; Takeda, N; Kubo, T

    1998-08-01

    Offset auditory responses were investigated by electroencephalography mainly in the 1970s, but since then no particular attention has been paid to them. Among the studies using magnetoencephalography (MEG) devices there are, to our knowledge, only three studies of the auditory off-response, and no significant variance has ever been observed between the source locations of on- and off-responses elicited from pure tones. We measured auditory evoked magnetic fields (AEFs) to various frequency pure tone stimulation in 5 healthy subjects with a 122-channel helmet-shaped magnetometer, and compared the distributions of the source locations of auditory N100m-Off (magnetic off-response around 100 ms) with those of N100m-On. Their spatial distributions were quite close to each other, and yet they were significantly different. PMID:9721944

  8. Passive-scheme analysis for solving the untrusted source problem in quantum key distribution

    SciTech Connect

    Peng Xiang; Xu Bingjie; Guo Hong

    2010-04-15

    As a practical method, the passive scheme is useful to monitor the photon statistics of an untrusted source in a 'Plug and Play' quantum key distribution (QKD) system. In a passive scheme, three kinds of monitor mode can be adopted: average photon number (APN) monitor, photon number analyzer (PNA), and photon number distribution (PND) monitor. In this paper, the security analysis is rigorously given for the APN monitor, while for the PNA, the analysis, including statistical fluctuation and random noise, is addressed with a confidence level. The results show that the PNA can achieve better performance than the APN monitor and can asymptotically approach the theoretical limit of the PND monitor. Also, the passive scheme with the PNA works efficiently when the signal-to-noise ratio (R{sup SN}) is not too low and so is highly applicable to solve the untrusted source problem in the QKD system.

  9. Evaluating the effect of network density and geometric distribution on kinematic source inversion models

    NASA Astrophysics Data System (ADS)

    Zhang, Youbing; Dalguer, Luis A.; Song, Seok Goo; Clinton, John; Giardini, Domenico

    2015-01-01

    The effect of network density and geometric distribution on kinematic non-linear source inversion is investigated by inverting synthetic ground motions from a buried strike-slip fault (Mw 6.5), that have been generated by dynamic spontaneous rupture modelling. For the inversion, we use a physics-based regularized Yoffe function as slip velocity function. We test three different cases of station network geometry: (i) single station, varying azimuth and epicentral distance; (ii) multistation circular configurations, that is stations at similar distances from the fault, and regularly spaced around the fault; (iii) irregular multistation configurations using different numbers of stations. Our results show: (1) single station tests suggest that it may be possible to obtain a relatively good source model even using a single station. The best source model using a single station is obtained with stations at which amplitude ratios between three components are not large. We infer that both azimuthal angle and source-to-station distance play an important role in the design of optimal seismic network for source inversion. (2) Multistation tests show that the quality of the inverted source systematically correlates neither with the number of stations, nor with waveform misfit. (3) Waveform misfit has a direct correlation with the number of stations, resulting in overfitting the observed data without any systematic improvement of the source. It suggests that the best source model is not necessarily derived from the model with minimum waveform misfit. (4) A seismic network with a small number of well-spaced stations around the fault may be sufficient to obtain acceptable source inversion.

  10. A Monte Carlo study on dose distribution evaluation of Flexisource 192Ir brachytherapy source

    PubMed Central

    Alizadeh, Majid; Ghorbani, Mahdi; Haghparast, Abbas; Zare, Naser; Ahmadi Moghaddas, Toktam

    2015-01-01

    Aim The aim of this study is to evaluate the dose distribution of the Flexisource 192Ir source. Background Dosimetric evaluation of brachytherapy sources is recommended by task group number 43 (TG. 43) of American Association of Physicists in Medicine (AAPM). Materials and methods MCNPX code was used to simulate Flexisource 192Ir source. Dose rate constant and radial dose function were obtained for water and soft tissue phantoms and compared with previous data on this source. Furthermore, dose rate along the transverse axis was obtained by simulation of the Flexisource and a point source and the obtained data were compared with those from Flexiplan treatment planning system (TPS). Results The values of dose rate constant obtained for water and soft tissue phantoms were equal to 1.108 and 1.106, respectively. The values of the radial dose function are listed in the form of tabulated data. The values of dose rate (cGy/s) obtained are shown in the form of tabulated data and figures. The maximum difference between TPS and Monte Carlo (MC) dose rate values was 11% in a water phantom at 6.0 cm from the source. Conclusion Based on dosimetric parameter comparisons with values previously published, the accuracy of our simulation of Flexisource 192Ir was verified. The results of dose rate constant and radial dose function in water and soft tissue phantoms were the same for Flexisource and point sources. For Flexisource 192Ir source, the results of TPS calculations in a water phantom were in agreement with the simulations within the calculation uncertainties. Furthermore, the results from the TPS calculation for Flexisource and MC calculation for a point source were practically equal within the calculation uncertainties. PMID:25949224

  11. Influence of the electron source distribution on field-aligned currents

    NASA Astrophysics Data System (ADS)

    Bruening, K.; Goertz, C. K.

    1985-01-01

    The field-aligned current density above a discrete auroral arc has been deduced from the downward electron flux and magnetic field measurements onboard the rocket Porcupine flight 4. Both measurements show that the field-aligned current density is, in spite of decreasing peak energies towards the edge of the arc, about 4 times higher there than in the center of the arc. This can be explained by using the single particle description for an anisotropic electron source distribution.

  12. Distribution and probable source of nitrate in ground water of Paradise Valley, Arizona

    SciTech Connect

    Silver, B.A.; Fielden, J.R.

    1980-01-01

    Two theories have been proposed regarding the source of nitrate in Paradise Valley ground water: one suggests contamination by fertilizers and by treated wastewater effluent, and the other suggests that ammonium chloride, leached from tuffs in the adjacent Superstition Mountains, is oxidized to nitrate and deposited in a braided stream complex. The geology, hydrogeology, and distribution of nitrate in Paradise Valley ground water are described.

  13. Temporal-spatial distribution of non-point source pollution in a drinking water source reservoir watershed based on SWAT

    NASA Astrophysics Data System (ADS)

    Wang, M.; Cheng, W.; Yu, B.-S.; Fang, Y.

    2015-05-01

    The conservation of drinking water source reservoirs has a close relationship between regional economic development and people's livelihood. Research on the non-point pollution characteristics in its watershed is crucial for reservoir security. Tang Pu Reservoir watershed was selected as the study area. The non-point pollution model of Tang Pu Reservoir was established based on the SWAT (Soil and Water Assessment Tool) model. The model was adjusted to analyse the temporal-spatial distribution patterns of total nitrogen (TN) and total phosphorus (TP). The results showed that the loss of TN and TP in the reservoir watershed were related to precipitation in flood season. And the annual changes showed an "M" shape. It was found that the contribution of loss of TN and TP accounted for 84.5% and 85.3% in high flow years, and for 70.3% and 69.7% in low flow years, respectively. The contributions in normal flow years were 62.9% and 63.3%, respectively. The TN and TP mainly arise from Wangtan town, Gulai town, and Wangyuan town, etc. In addition, it was found that the source of TN and TP showed consistency in space.

  14. Unveiling the Gamma-Ray Source Count Distribution Below the Fermi Detection Limit with Photon Statistics

    NASA Astrophysics Data System (ADS)

    Zechlin, Hannes-S.; Cuoco, Alessandro; Donato, Fiorenza; Fornengo, Nicolao; Vittino, Andrea

    2016-08-01

    The source-count distribution as a function of their flux, {dN}/{dS}, is one of the main quantities characterizing gamma-ray source populations. We employ statistical properties of the Fermi Large Area Telescope (LAT) photon counts map to measure the composition of the extragalactic gamma-ray sky at high latitudes (| b| ≥slant 30°) between 1 and 10 GeV. We present a new method, generalizing the use of standard pixel-count statistics, to decompose the total observed gamma-ray emission into (a) point-source contributions, (b) the Galactic foreground contribution, and (c) a truly diffuse isotropic background contribution. Using the 6 yr Fermi-LAT data set (P7REP), we show that the {dN}/{dS} distribution in the regime of so far undetected point sources can be consistently described with a power law with an index between 1.9 and 2.0. We measure {dN}/{dS} down to an integral flux of ∼ 2× {10}-11 {{cm}}-2 {{{s}}}-1, improving beyond the 3FGL catalog detection limit by about one order of magnitude. The overall {dN}/{dS} distribution is consistent with a broken power law, with a break at {2.1}-1.3+1.0× {10}-8 {{cm}}-2 {{{s}}}-1. The power-law index {n}1={3.1}-0.5+0.7 for bright sources above the break hardens to {n}2=1.97+/- 0.03 for fainter sources below the break. A possible second break of the {dN}/{dS} distribution is constrained to be at fluxes below 6.4× {10}-11 {{cm}}-2 {{{s}}}-1 at 95% confidence level. The high-latitude gamma-ray sky between 1 and 10 GeV is shown to be composed of ∼25% point sources, ∼69.3% diffuse Galactic foreground emission, and ∼6% isotropic diffuse background.

  15. Experimental measurement-device-independent quantum key distribution with imperfect sources

    NASA Astrophysics Data System (ADS)

    Tang, Zhiyuan; Wei, Kejin; Bedroya, Olinka; Qian, Li; Lo, Hoi-Kwong

    2016-04-01

    Measurement-device-independent quantum key distribution (MDI-QKD), which is immune to all detector side-channel attacks, is the most promising solution to the security issues in practical quantum key distribution systems. Although several experimental demonstrations of MDI-QKD have been reported, they all make one crucial but not yet verified assumption, that is, there are no flaws in state preparation. Such an assumption is unrealistic and security loopholes remain in the source. Here we present a MDI-QKD experiment with the modulation error taken into consideration. By applying the loss-tolerant security proof by Tamaki et al. [Phys. Rev. A 90, 052314 (2014)], 10.1103/PhysRevA.90.052314, we distribute secure keys over fiber links up to 40 km with imperfect sources, which would not have been possible under previous security proofs. By simultaneously closing loopholes at the detectors and a critical loophole—modulation error in the source, our work shows the feasibility of secure QKD with practical imperfect devices.

  16. Energy Distribution of a Prototype KSTAR Neutral Beam Ion Source for 300 s Arc Discharge

    NASA Astrophysics Data System (ADS)

    Chang, Doo-Hee; Jeong, Seung Ho; Oh, Byung-Hoon

    2008-02-01

    A neutral beam test-stand (NBTS) system has been developed for the extraction of a 300 s deuterium beam of 120 kV/65 A as an auxiliary heating system of Korea Superconducting Tokamak Advanced Research (KSTAR). The prototype long pulse ion source (LPIS) consists of a plasma generator and a set of tetrode accelerators. Beam extraction for 300 s was achieved at a maximum hydrogen beam power of 1.6 MW (70 kV/23 A) with an arc discharge power of 63 kW. The energy distribution of the ion source was analyzed by water-flow calorimetry (WFC) by monitoring the cooling-water temperature during the arc discharge. The power dissipation rate on the accelerator column was 0.97% of the total extracted ion beam power with a power loss of 0.2% caused by the collision of back stream electrons with the electron dump plate of the plasma generator. 74.2% of the total energy of was estimated to be distributed in the plasma generator and the accelerator for an arc discharge of 300 s. Also, 75.6% of the total energy was distributed in the ion source for an arc discharge of 2 s. The remaining energy was lost through the structures around the water-cooling path.

  17. Source contributions to the regional distribution of secondary particulate matter in California

    NASA Astrophysics Data System (ADS)

    Ying, Qi; Kleeman, Michael J.

    Source contributions to PM2.5 nitrate, sulfate and ammonium ion concentrations in California's San Joaquin Valley (SJV) (4-6 January 1996) and South Coast Air Basin (SoCAB) surrounding Los Angeles (23-25 September 1996) were predicted using a three-dimensional source-oriented Eulerian air quality model. The air quality model tracks the formation of PM2.5 nitrate, sulfate and ammonium ion from primary particles and precursor gases emitted from different sources though a mathematical simulation of emission, chemical reaction, gas-to-particle conversion, transport and deposition. The observed PM2.5 nitrate, sulfate and ammonium ion concentrations, and the mass distribution of nitrate, sulfate and ammonium ion as a function of particle size have been successfully reproduced by the model simulation. Approximately 45-57% of the PM2.5 nitrate and 34-40% of the PM2.5 ammonium ion in the SJV is formed from precursor gaseous species released from sources upwind of the valley. In the SoCAB, approximately 83% of the PM2.5 nitrate and 82% of the PM2.5 ammonium ion is formed from precursor gaseous species released from sources within the air basin. In the SJV, transportation related sources contribute approximately 24-30% of the PM2.5 nitrate (diesel engines ˜13.5-17.0%, catalyst equipped gasoline engines ˜10.2-12.8% and non-catalyst equipped gasoline engines ˜0.3-0.4%). In the SoCAB, transportation related sources directly contribute to approximately 67% of the PM2.5 nitrate (diesel engines 34.6%, non-catalyst equipped gasoline engine 4.7% and catalyst equipped gasoline engine 28.1%). PM2.5 ammonium ion concentrations in the SJV were dominated by area (including animal) NH 3 sources (16.7-25.3%), soil (7.2-10.9%), fertilizer NH 3 sources (11.4-17.3%) and point NH 3 sources (14.3-21.7%). In the SoCAB, ammonium ion is mainly associated with animal sources (28.2%) and catalyst equipped gasoline engines (16.2%). In both regions, the majority of the relatively low PM2.5 sulfate

  18. Polycyclic aromatic hydrocarbons in the dagang oilfield (china): distribution, sources, and risk assessment.

    PubMed

    Jiao, Haihua; Rui, Xiaoping; Wu, Shanghua; Bai, Zhihui; Zhuang, Xuliang; Huang, Zhanbin

    2015-06-01

    The levels of 16 polycyclic aromatic hydrocarbons (PAHs) were investigated in 27 upper layer (0-25 cm) soil samples collected from the Dagang Oilfield (China) in April 2013 to estimate their distribution, possible sources, and potential risks posed. The total concentrations of PAHs (∑PAHs) varied between 103.6 µg·kg(-1) and 5872 µg·kg(-1), with a mean concentration of 919.8 µg·kg(-1); increased concentrations were noted along a gradient from arable desert soil (mean 343.5 µg·kg(-1)), to oil well areas (mean of 627.3 µg·kg(-1)), to urban and residential zones (mean of 1856 µg·kg(-1)). Diagnostic ratios showed diverse source of PAHs, including petroleum, liquid fossil fuels, and biomass combustion sources. Combustion sources were most significant for PAHs in arable desert soils and residential zones, while petroleum sources were a significant source of PAHs in oilfield areas. Based ontheir carcinogenity, PAHs were classified as carcinogenic (B) or not classified/non-carcinogenic (NB). The total concentrations of carcinogenic PAHs (∑BPAHs) varied from 13.3 µg·kg(-1) to 4397 µg·kg(-1) across all samples, with a mean concentration of 594.4 µg·kg(-1). The results suggest that oilfield soil is subject to a certain level of ecological environment risk. PMID:26016436

  19. Polycyclic Aromatic Hydrocarbons in the Dagang Oilfield (China): Distribution, Sources, and Risk Assessment

    PubMed Central

    Jiao, Haihua; Rui, Xiaoping; Wu, Shanghua; Bai, Zhihui; Zhuang, Xuliang; Huang, Zhanbin

    2015-01-01

    The levels of 16 polycyclic aromatic hydrocarbons (PAHs) were investigated in 27 upper layer (0–25 cm) soil samples collected from the Dagang Oilfield (China) in April 2013 to estimate their distribution, possible sources, and potential risks posed. The total concentrations of PAHs (∑PAHs) varied between 103.6 µg·kg−1 and 5872 µg·kg−1, with a mean concentration of 919.8 µg·kg−1; increased concentrations were noted along a gradient from arable desert soil (mean 343.5 µg·kg−1), to oil well areas (mean of 627.3 µg·kg−1), to urban and residential zones (mean of 1856 µg·kg−1). Diagnostic ratios showed diverse source of PAHs, including petroleum, liquid fossil fuels, and biomass combustion sources. Combustion sources were most significant for PAHs in arable desert soils and residential zones, while petroleum sources were a significant source of PAHs in oilfield areas. Based ontheir carcinogenity, PAHs were classified as carcinogenic (B) or not classified/non-carcinogenic (NB). The total concentrations of carcinogenic PAHs (∑BPAHs) varied from 13.3 µg·kg−1 to 4397 µg·kg−1 across all samples, with a mean concentration of 594.4 µg·kg−1. The results suggest that oilfield soil is subject to a certain level of ecological environment risk. PMID:26016436

  20. A review of the environmental distribution, fate, and control of tetrabromobisphenol A released from sources.

    PubMed

    Malkoske, Tyler; Tang, Yulin; Xu, Wenying; Yu, Shuili; Wang, Hongtao

    2016-11-01

    Tetrabromobisphenol A (TBBPA), a high use brominated flame retardant (BFR), raising concerns of widespread pollution and harm to human and ecological health. BFR manufacturing, TBBPA-based product manufacturing, e-waste recycling, and wastewater treatment plants have been identified as the main emission point sources. This paper discusses the occurrence, distribution, and fate of TBBPA from source to the environment. After release to the environment, TBBPA may undergo adsorption, photolysis, and biological degradation. Exposure of humans and biota is also discussed along with the role of treatment and regulations in reducing release of TBBPA to the environment and exposure risks. In general this review found stronger enforcement of existing legislation, and investment in treatment of e-waste plastics and wastewater from emission point sources could be effective methods in reducing release and exposure of TBBPA in the environment. PMID:27325014

  1. Source-Manipulating Wavelength-Dependent Continuous-Variable Quantum Key Distribution with Heterodyne Detectors

    NASA Astrophysics Data System (ADS)

    Lv, Geli; Huang, Dazu; Guo, Ying

    2016-05-01

    The intensities of signal and local oscillator (LO) can be elegantly manipulated for the noise-based quantum system while manipulating the wavelength-dependent modulation in source to increase the performance of the continuous-variable key distribution in terms of the secret key rate and maximal transmission distance. The source-based additional noises can be tuned and stabilized to the suitable values to eliminate the effect of the LO fluctuations and defeat the potential attacks in imperfect quantum channels. It is firmly proved that the secret key rate can be manipulated in source over imperfect channels by the intensities of signal and LO with different wavelengths, which have an effect on the optimal signal-to-noise ratio of the heterodyne detectors resulting from the detection efficiency and the additional electronic noise as well. Simulation results show that there is a nice balance between the secret key rate and the maximum transmission distance.

  2. Balancing continuous-variable quantum key distribution with source-tunable linear optics cloning machine

    NASA Astrophysics Data System (ADS)

    Guo, Ying; Lv, Geli; Zeng, Guihua

    2015-11-01

    We show that the tolerable excess noise can be dynamically balanced in source preparation while inserting a tunable linear optics cloning machine (LOCM) for balancing the secret key rate and the maximal transmission distance of continuous-variable quantum key distribution (CVQKD). The intensities of source noise are sensitive to the tunable LOCM and can be stabilized to the suitable values to eliminate the impact of channel noise and defeat the potential attacks even in the case of the degenerated linear optics amplifier (LOA). The LOCM-additional noise can be elegantly employed by the reference partner of reconciliation to regulate the secret key rate and the transmission distance. Simulation results show that there is a considerable improvement in the secret key rate of the LOCM-based CVQKD while providing a tunable LOCM for source preparation with the specified parameters in suitable ranges.

  3. Heralded single-photon sources for quantum-key-distribution applications

    NASA Astrophysics Data System (ADS)

    Schiavon, Matteo; Vallone, Giuseppe; Ticozzi, Francesco; Villoresi, Paolo

    2016-01-01

    Single-photon sources (SPSs) are a fundamental building block for optical implementations of quantum information protocols. Among SPSs, multiple crystal heralded single-photon sources seem to give the best compromise between high pair production rate and low multiple photon events. In this work, we study their performance in a practical quantum-key-distribution experiment, by evaluating the achievable key rates. The analysis focuses on the two different schemes, symmetric and asymmetric, proposed for the practical implementation of heralded single-photon sources, with attention on the performance of their composing elements. The analysis is based on the protocol proposed by Bennett and Brassard in 1984 and on its improvement exploiting decoy state technique. Finally, a simple way of exploiting the postselection mechanism for a passive, one decoy state scheme is evaluated.

  4. Qualitative analysis of precipiation distribution in Poland with use of different data sources

    NASA Astrophysics Data System (ADS)

    Walawender, J.; Dyras, I.; Łapeta, B.; Serafin-Rek, D.; Twardowski, A.

    2008-04-01

    Geographical Information Systems (GIS) can be used to integrate data from different sources and in different formats to perform innovative spatial and temporal analysis. GIS can be also applied for climatic research to manage, investigate and display all kinds of weather data. The main objective of this study is to demonstrate that GIS is a useful tool to examine and visualise precipitation distribution obtained from different data sources: ground measurements, satellite and radar data. Three selected days (30 cases) with convective rainfall situations were analysed. Firstly, scalable GRID-based approach was applied to store data from three different sources in comparable layout. Then, geoprocessing algorithm was created within ArcGIS 9.2 environment. The algorithm included: GRID definition, reclassification and raster algebra. All of the calculations and procedures were performed automatically. Finally, contingency tables and pie charts were created to show relationship between ground measurements and both satellite and radar derived data. The results were visualised on maps.

  5. Source apportionment of ambient fine particle size distribution using positive matrix factorization in Erfurt, Germany

    PubMed Central

    Yue, Wei; Stölzel, Matthias; Cyrys, Josef; Pitz, Mike; Heinrich, Joachim; Kreyling, Wolfgang G.; Wichmann, H.-Erich; Peters, Annette; Wang, Sheng; Hopke, Philip K.

    2008-01-01

    Particle size distribution data collected between September 1997 and August 2001 in Erfurt, Germany were used to investigate the sources of ambient particulate matter by positive matrix factorization (PMF). A total of 29,313 hourly averaged particle size distribution measurements covering the size range of 0.01 to 3.0 μm were included in the analysis. The particle number concentrations (cm−3) for the 9 channels in the ultrafine range, and mass concentrations (ng m−3) for the 41 size bins in the accumulation mode and particle up to 3 μm in aerodynamic diameter were used in the PMF. The analysis was performed separately for each season. Additional analyses were performed including calculations of the correlations of factor contributions with gaseous pollutants (O3, NO, NO2, CO and SO2) and particle composition data (sulfate, organic carbon and elemental carbon), estimating the contributions of each factor to the total number and mass concentration, identifying the directional locations of the sources using the conditional probability function, and examining the diurnal patterns of factor scores. These results were used to assist in the interpretation of the factors. Five factors representing particles from airborne soil, ultrafine particles from local traffic, secondary aerosols from local fuel combustion, particles from remote traffic sources, and secondary aerosols from multiple sources were identified in all seasons. PMID:18433834

  6. Regional Sources of Nitrous Oxide over the United States: Seasonal Variation and Spatial Distribution

    SciTech Connect

    Miller, S. M.; Kort, E. A.; Hirsch, A. I.; Dlugokencky, E. J.; Andrews, A. E.; Xu, X.; Tian, H.; Nehrkorn, T.; Eluszkiewicz, J.; Michalak, A. M.; Wofsy, S. C.

    2012-01-01

    This paper presents top-down constraints on the magnitude, spatial distribution, and seasonality of nitrous oxide (N{sub 2}O) emissions over the central United States. We analyze data from tall towers in 2004 and 2008 using a high resolution Lagrangian particle dispersion model paired with both geostatistical and Bayesian inversions. Our results indicate peak N{sub 2}O emissions in June with a strong seasonal cycle. The spatial distribution of sources closely mirrors data on fertilizer application with particularly large N{sub 2}O sources over the US Cornbelt. Existing inventories for N{sub 2}O predict emissions that differ substantially from the inverse model results in both seasonal cycle and magnitude. We estimate a total annual N{sub 2}O budget over the central US of 0.9-1.2 TgN/yr and an extrapolated budget for the entire US and Canada of 2.1-2.6 TgN/yr. By this estimate, the US and Canada account for 12-15% of the total global N{sub 2}O source or 32-39% of the global anthropogenic source as reported by the Intergovernmental Panel on Climate Change in 2007.

  7. Performance metrics and variance partitioning reveal sources of uncertainty in species distribution models

    USGS Publications Warehouse

    Watling, James I.; Brandt, Laura A.; Bucklin, David N.; Fujisaki, Ikuko; Mazzotti, Frank J.; Romanach, Stephanie; Speroterra, Carolina

    2015-01-01

    Species distribution models (SDMs) are widely used in basic and applied ecology, making it important to understand sources and magnitudes of uncertainty in SDM performance and predictions. We analyzed SDM performance and partitioned variance among prediction maps for 15 rare vertebrate species in the southeastern USA using all possible combinations of seven potential sources of uncertainty in SDMs: algorithms, climate datasets, model domain, species presences, variable collinearity, CO2 emissions scenarios, and general circulation models. The choice of modeling algorithm was the greatest source of uncertainty in SDM performance and prediction maps, with some additional variation in performance associated with the comprehensiveness of the species presences used for modeling. Other sources of uncertainty that have received attention in the SDM literature such as variable collinearity and model domain contributed little to differences in SDM performance or predictions in this study. Predictions from different algorithms tended to be more variable at northern range margins for species with more northern distributions, which may complicate conservation planning at the leading edge of species' geographic ranges. The clear message emerging from this work is that researchers should use multiple algorithms for modeling rather than relying on predictions from a single algorithm, invest resources in compiling a comprehensive set of species presences, and explicitly evaluate uncertainty in SDM predictions at leading range margins.

  8. Effect of tissue inhomogeneity on dose distribution of point sources of low-energy electrons.

    PubMed

    Kwok, C S; Bialobzyski, P J; Yu, S K; Prestwich, W V

    1990-01-01

    Perturbation in dose distributions of point sources of low-energy electrons at planar interfaces of cortical bone (CB) and red marrow (RM) was investigated experimentally and by Monte Carlo codes EGS and the TIGER series. Ultrathin LiF thermoluminescent dosimeters were used to measure the dose distributions of point sources of 204Tl and 147Pm in RM. When the point sources were at 12 mg/cm2 from a planar interface of CB and RM equivalent plastics, dose enhancement ratios in RM averaged over the region 0-12 mg/cm2 from the interface were measured to be 1.08 +/- 0.03 (SE) and 1.03 +/- 0.03 (SE) for 204Tl and 147Pm, respectively. The Monte Carlo codes predicted 1.05 +/- 0.02 and 1.01 +/- 0.02 for the two nuclides, respectively. However, EGS gave consistently 3% higher dose in the dose scoring region than the TIGER series when point sources of monoenergetic electrons up to 0.75 MeV energy were considered in the homogeneous RM situation or in the CB and RM heterogeneous situation. By means of the TIGER series, it was demonstrated that aluminum, which is normally assumed to be equivalent to CB in radiation dosimetry, leads to an overestimation of backscattering of low-energy electrons in soft tissue at a CB-soft-tissue interface by as much as a factor of 2. PMID:2233564

  9. Analysis of electron energy distribution function in the Linac4 H⁻ source.

    PubMed

    Mochizuki, S; Mattei, S; Nishida, K; Hatayama, A; Lettry, J

    2016-02-01

    To understand the Electron Energy Distribution Function (EEDF) in the Radio Frequency Inductively Coupled Plasmas (RF-ICPs) in hydrogen negative ion sources, the detailed analysis of the EEDFs using numerical simulation and the theoretical approach based on Boltzmann equation has been performed. It is shown that the EEDF of RF-ICPs consists of two parts, one is the low energy part which obeys Maxwellian distribution and the other is high energy part deviated from Maxwellian distribution. These simulation results have been confirmed to be reasonable by the analytical approach. The results suggest that it is possible to enhance the dissociation of molecules and the resultant H(-) negative ion production by reducing the gas pressure. PMID:26931990

  10. Spatial distribution of the source-receptor relationship of sulfur in Northeast Asia

    NASA Astrophysics Data System (ADS)

    Kajino, M.; Ueda, H.; Sato, K.; Sakurai, T.

    2011-07-01

    The spatial distribution of the source-receptor relationship (SRR) of sulfur over Northeast Asia was examined using a chemical transport model (RAQM) off-line coupled with a meteorological model (MM5). The simulation was conducted for the entire year of 2002. The results were evaluated using monitoring data for six remote stations of the Acid Deposition Monitoring Network in East Asia (EANET). The modeled SO2 and O3 concentrations agreed well with the observations quantitatively. The modeled aerosol and wet deposition fluxes of SO42- were underestimated by 30 % and 50 %, respectively. The domain was divided into 5 source-receptor regions: (I) North China; (II) Central China; (III) South China; (IV) South Korea; and (V) Japan. The sulfur deposition in each receptor region amounted to about 50-75 % of the emissions from the same region. The largest contribution to the deposition in each region was originated from the same region, accounting for 53-84 %. The second largest contribution was due to Region II, supplying 14-43 %. The spatial distributions of the SRRs revealed that subregional values varied by about two times more than regional averages due to nonuniformity across the deposition fields. Examining the spatial distributions of the deposition fields was important for identifying subregional areas where the deposition was highest within a receptor region. The horizontal distribution changed substantially according to season.

  11. Spatial distribution of the source-receptor relationship of sulfur in Northeast Asia

    NASA Astrophysics Data System (ADS)

    Kajino, M.; Ueda, H.; Sato, K.; Sakurai, T.

    2010-12-01

    The spatial distribution of the source-receptor relationship (SRR) of sulfur over Northeast Asia was examined using an off-line coupled meteorological/chemical transport model (MM5/RAQM). The simulation was conducted for the entire year of 2002. The results were evaluated using monitoring data for six remote stations of the Acid Deposition Monitoring Network in East Asia (EANET). The modeled SO2 and O3 concentrations agreed well with the observations quantitatively. The modeled aerosol and wet deposition fluxes of SO42- were underestimated by 30% and 50%, respectively, whereas the modeled precipitation was overestimated by 1.6 to 1.9 times. The domain was divided into 5 source-receptor regions: I, North China; II, Central China; III, South China; IV, South Korea; and V, Japan. The sulfur deposition in each receptor region amounted to about 50-75% of the emissions from the same region. The largest contribution to the deposition in each region was the domestic origin, accounting for 53-84%. The second largest contribution after the domestic origin was due to region II, supplying 14-43%, outside region II itself. The spatial distributions of the SRRs revealed that subregional values varied by about two times more than regional averages due to nonuniformity across the deposition fields. Examining the spatial distributions of the deposition fields was important for identifying subregional areas where the deposition was highest within a receptor region. The horizontal distribution changed substantially according to season.

  12. Genotype and haplotype distributions of MTHFR677C>T and 1298A>C single nucleotide polymorphisms: a meta-analysis.

    PubMed

    Ogino, Shuji; Wilson, Robert B

    2003-01-01

    Common single nucleotide polymorphisms (SNPs; 677C>T and 1298A>C) in the methylenetetrahydrofolate reductase gene ( MTHFR) decrease the activity of the enzyme, leading to hyperhomocysteinemia, particularly in folate-deficient states. We calculate herein the haplotype frequencies of the MTHFR 677 and 1298 polymorphisms in pooled general populations derived from published data. We selected 16 articles that provided reliable data on combined MTHFR genotypes in general populations ( n = 5389). The combined data comprised the following totals for each genotype at nucleotide positions 677 and 1298: 838 CC/AA (i.e., 677CC/1298AA), 1225 CC/AC, 489 CC/CC, 1120 CT/AA, 1093 CT/AC, 8 CT/CC, 606 TT/AA, 10 TT/AC, and 0 TT/CC. The estimated haplotype frequencies, and the fractional contribution of each, were 677C/1298A, 0.37; 677C/1298C, 0.31; 677T/1298A, 0.32; and 677T/1298C, 0.0023 to 0.0034. Thus, a vast majority of 677T alleles and 1298C alleles are associated with 1298A alleles and 677C alleles, respectively. There may be an increased frequency of the very rare cis 677T/1298C haplotype in some parts of the United Kingdom and Canada, possibly due to a founder effect. Further studies on both SNPs are needed to determine their exact role in various clinical settings. PMID:12560871

  13. 10 CFR 32.74 - Manufacture and distribution of sources or devices containing byproduct material for medical use.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 1 2011-01-01 2011-01-01 false Manufacture and distribution of sources or devices... SPECIFIC DOMESTIC LICENSES TO MANUFACTURE OR TRANSFER CERTAIN ITEMS CONTAINING BYPRODUCT MATERIAL Generally Licensed Items § 32.74 Manufacture and distribution of sources or devices containing byproduct material...

  14. 10 CFR 32.74 - Manufacture and distribution of sources or devices containing byproduct material for medical use.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Manufacture and distribution of sources or devices... SPECIFIC DOMESTIC LICENSES TO MANUFACTURE OR TRANSFER CERTAIN ITEMS CONTAINING BYPRODUCT MATERIAL Generally Licensed Items § 32.74 Manufacture and distribution of sources or devices containing byproduct material...

  15. 10 CFR 32.74 - Manufacture and distribution of sources or devices containing byproduct material for medical use.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 1 2013-01-01 2013-01-01 false Manufacture and distribution of sources or devices... SPECIFIC DOMESTIC LICENSES TO MANUFACTURE OR TRANSFER CERTAIN ITEMS CONTAINING BYPRODUCT MATERIAL Specifically Licensed Items § 32.74 Manufacture and distribution of sources or devices containing...

  16. 10 CFR 32.74 - Manufacture and distribution of sources or devices containing byproduct material for medical use.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 1 2012-01-01 2012-01-01 false Manufacture and distribution of sources or devices... SPECIFIC DOMESTIC LICENSES TO MANUFACTURE OR TRANSFER CERTAIN ITEMS CONTAINING BYPRODUCT MATERIAL Generally Licensed Items § 32.74 Manufacture and distribution of sources or devices containing byproduct material...

  17. 10 CFR 32.74 - Manufacture and distribution of sources or devices containing byproduct material for medical use.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 1 2014-01-01 2014-01-01 false Manufacture and distribution of sources or devices... SPECIFIC DOMESTIC LICENSES TO MANUFACTURE OR TRANSFER CERTAIN ITEMS CONTAINING BYPRODUCT MATERIAL Specifically Licensed Items § 32.74 Manufacture and distribution of sources or devices containing...

  18. Sources/sinks analysis with satellite sensing for exploring global atmospheric CO2 distributions

    NASA Astrophysics Data System (ADS)

    Shim, C.; Nassar, R.; Kim, J.

    2010-12-01

    There is growing interest in CO2 budget analysis since space-borne measurements of global CO2 distribution have been conducted (e.g, GOSAT project). Here we simulated the global CO2 distribution to estimate individual source/sink contributions. The chemical transport model (GEOS-Chem) was used in order to simulate the global CO2 distribution with updated global sources/sinks with 2°x2.5° horizontal resolution. In addition, 3-D emissions from aviation and chemical oxidation of CO are implemented. The model simulated CO2 amounts were compared with the GOSAT column averaged CO2 column (SWIR L2 data) from April 2009 to May 2010. The seasonal cycles of CO2 concentration were compared and the regional patterns of CO2 distribution are explained by the model with a systemic difference by 1 ~ 2% in the CO2 concentration. In other work, the GEOS-Chem CO2 concentrations show reasonable agreement with GLOBALVIEW-CO2. We further estimated the sources/sinks contributions to the global CO2 budget through 9 tagged CO2 tracers (fossil fuels, ocean exchanges, biomass burning, biofuel burning, balanced biosphere, net terrestrial exchange, ship emissions, aviation emissions, and oxidation from carbon precursors) over the years 2005-2009. Global CO2 concentration shows an increase of 2.1 ppbv/year in which the human fossil fuel and cement emissions are the main driving force (5.0 ppbv/year) for the trend. Net terrestrial and oceanic exchange of CO2 are main sinks (-2.1 ppbv/year and -0.7 ppbv/year, respectively). Our model results will help to suggest the level of reduction in global human CO2 emissions which could control the global CO2 trends in 21th century.

  19. Acoustic Emission Source Location Using a Distributed Feedback Fiber Laser Rosette

    PubMed Central

    Huang, Wenzhu; Zhang, Wentao; Li, Fang

    2013-01-01

    This paper proposes an approach for acoustic emission (AE) source localization in a large marble stone using distributed feedback (DFB) fiber lasers. The aim of this study is to detect damage in structures such as those found in civil applications. The directional sensitivity of DFB fiber laser is investigated by calculating location coefficient using a method of digital signal analysis. In this, autocorrelation is used to extract the location coefficient from the periodic AE signal and wavelet packet energy is calculated to get the location coefficient of a burst AE source. Normalization is processed to eliminate the influence of distance and intensity of AE source. Then a new location algorithm based on the location coefficient is presented and tested to determine the location of AE source using a Delta (Δ) DFB fiber laser rosette configuration. The advantage of the proposed algorithm over the traditional methods based on fiber Bragg Grating (FBG) include the capability of: having higher strain resolution for AE detection and taking into account two different types of AE source for location. PMID:24141266

  20. Spatial distribution and source apportionment of PCBs in sediments around İzmit industrial complexes, Turkey.

    PubMed

    Gedik, Kadir; Demircioğlu, Filiz; Imamoğlu, Ipek

    2010-11-01

    The spatial distribution, degree of pollution and major sources of PCBs were evaluated in surficial sediments within the heavily urbanized and industrialized İzmit Bay and its main freshwater inputs. ΣPCB concentrations range from 2.90 to 85.4ngg(-1) in marine sediments and from ND to 47.7ngg(-1) in freshwater sediments. Results suggest that high concentrations of ΣPCBs were localized around a chlor-alkali plant and an industry that handles bulk liquid, dry and drummed chemicals, and petroleum products in the Bay. Using a chemical mass balance receptor model (CMB), major sources of PCBs in the region were investigated. The CMB model identified Aroclor 1254 and 1260 to be the major PCB sources in marine sediments and the less chlorinated Aroclor 1248 and 1242 as the major PCB sources in freshwater sediments. The potential sources for the PCBs were briefly discussed in terms of their use in various industrial applications. PMID:20889182

  1. THE ENVIRONMENT AND DISTRIBUTION OF EMITTING ELECTRONS AS A FUNCTION OF SOURCE ACTIVITY IN MARKARIAN 421

    SciTech Connect

    Mankuzhiyil, Nijil; Ansoldi, Stefano; Tavecchio, Fabrizio

    2011-05-20

    For the high-frequency-peaked BL Lac object Mrk 421, we study the variation of the spectral energy distribution (SED) as a function of source activity, from quiescent to active. We use a fully automatized {chi}{sup 2}-minimization procedure, instead of the 'eyeball' procedure more commonly used in the literature, to model nine SED data sets with a one-zone synchrotron self-Compton (SSC) model and examine how the model parameters vary with source activity. The latter issue can finally be addressed now, because simultaneous broadband SEDs (spanning from optical to very high energy photon) have finally become available. Our results suggest that in Mrk 421 the magnetic field (B) decreases with source activity, whereas the electron spectrum's break energy ({gamma}{sub br}) and the Doppler factor ({delta}) increase-the other SSC parameters turn out to be uncorrelated with source activity. In the SSC framework, these results are interpreted in a picture where the synchrotron power and peak frequency remain constant with varying source activity, through a combination of decreasing magnetic field and increasing number density of {gamma} {<=} {gamma}{sub br} electrons: since this leads to an increased electron-photon scattering efficiency, the resulting Compton power increases, and so does the total (= synchrotron plus Compton) emission.

  2. Spatial distribution of the plasma parameters in the RF negative ion source prototype for fusion

    SciTech Connect

    Lishev, S.; Schiesko, L.; Wünderlich, D.; Fantz, U.

    2015-04-08

    A numerical model, based on the fluid plasma theory, has been used for description of the spatial distribution of the plasma parameters (electron density and temperature, plasma potential as well as densities of the three types of positive hydrogen ions) in the IPP prototype RF negative hydrogen ion source. The model covers the driver and the expansion plasma region of the source with their actual size and accounts for the presence of the magnetic filter field with its actual value and location as well as for the bias potential applied to the plasma grid. The obtained results show that without a magnetic filter the two 2D geometries considered, respectively, with an axial symmetry and a planar one, represent accurately the complex 3D structure of the source. The 2D model with a planar symmetry (where the E×B and diamagnetic drifts could be involved in the description) has been used for analysis of the influence, via the charged-particle and electron-energy fluxes, of the magnetic filter and of the bias potential on the spatial structure of the plasma parameters in the source. Benchmarking of results from the code to experimental data shows that the model reproduces the general trend in the axial behavior of the plasma parameters in the source.

  3. Spatial distribution of the plasma parameters in the RF negative ion source prototype for fusion

    NASA Astrophysics Data System (ADS)

    Lishev, S.; Schiesko, L.; Wünderlich, D.; Fantz, U.

    2015-04-01

    A numerical model, based on the fluid plasma theory, has been used for description of the spatial distribution of the plasma parameters (electron density and temperature, plasma potential as well as densities of the three types of positive hydrogen ions) in the IPP prototype RF negative hydrogen ion source. The model covers the driver and the expansion plasma region of the source with their actual size and accounts for the presence of the magnetic filter field with its actual value and location as well as for the bias potential applied to the plasma grid. The obtained results show that without a magnetic filter the two 2D geometries considered, respectively, with an axial symmetry and a planar one, represent accurately the complex 3D structure of the source. The 2D model with a planar symmetry (where the E×B and diamagnetic drifts could be involved in the description) has been used for analysis of the influence, via the charged-particle and electron-energy fluxes, of the magnetic filter and of the bias potential on the spatial structure of the plasma parameters in the source. Benchmarking of results from the code to experimental data shows that the model reproduces the general trend in the axial behavior of the plasma parameters in the source.

  4. Passive sources for the Bennett-Brassard 1984 quantum-key-distribution protocol with practical signals

    SciTech Connect

    Curty, Marcos; Ma Xiongfeng; Luetkenhaus, Norbert; Lo, Hoi-Kwong

    2010-11-15

    Most experimental realizations of quantum key distribution are based on the Bennett-Brassard 1984 (the so-called BB84) protocol. In a typical optical implementation of this scheme, the sender uses an active source to produce the required BB84 signal states. While active state preparation of BB84 signals is a simple and elegant solution in principle, in practice passive state preparation might be desirable in some scenarios, for instance, in those experimental setups operating at high transmission rates. Passive schemes might also be more robust against side-channel attacks than active sources. Typical passive devices involve parametric down-conversion. In this paper, we show that both coherent light and practical single-photon sources are also suitable for passive generation of BB84 signal states. Our method does not require any externally driven element, but only linear optical components and photodetectors. In the case of coherent light, the resulting key rate is similar to the one delivered by an active source. When the sender uses practical single-photon sources, however, the distance covered by a passive transmitter might be longer than that of an active configuration.

  5. Size distributions and source function of sea spray aerosol over the South China Sea

    NASA Astrophysics Data System (ADS)

    Chu, Yingjia; Sheng, Lifang; Liu, Qian; Zhao, Dongliang; Jia, Nan; Kong, Yawen

    2016-08-01

    The number concentrations in the radius range of 0.06-5 μm of aerosol particles and meteorological parameters were measured on board during a cruise in the South China Sea from August 25 to October 12, 2012. Effective fluxes in the reference height of 10 m were estimated by steady state dry deposition method based on the observed data, and the influences of different air masses on flux were discussed in this paper. The number size distribution was characterized by a bimodal mode, with the average total number concentration of (1.50 ± 0.76)×103 cm-3. The two mode radii were 0.099 µm and 0.886 µm, both of which were within the scope of accumulation mode. A typical daily average size distribution was compared with that measured in the Bay of Bengal. In the whole radius range, the number concentrations were in agreement with each other; the modes were more distinct in this study than that abtained in the Bay of Bengal. The size distribution of the fluxes was fitted with the sum of log-normal and power-law distribution. The impact of different air masses was mainly on flux magnitude, rather than the shape of spectral distribution. A semiempirical source function that is applicable in the radius range of 0.06 µm< r 80<0.3 µm with the wind speed varying from 1.00 m s-1 to 10.00 m s-1 was derived.

  6. The Hubble Legacy Archive ACS grism data

    NASA Astrophysics Data System (ADS)

    Kümmel, M.; Rosati, P.; Fosbury, R.; Haase, J.; Hook, R. N.; Kuntschner, H.; Lombardi, M.; Micol, A.; Nilsson, K. K.; Stoehr, F.; Walsh, J. R.

    2011-06-01

    A public release of slitless spectra, obtained with ACS/WFC and the G800L grism, is presented. Spectra were automatically extracted in a uniform way from 153 archival fields (or "associations") distributed across the two Galactic caps, covering all observations to 2008. The ACS G800L grism provides a wavelength range of 0.55-1.00 μm, with a dispersion of 40 Å/pixel and a resolution of ~80 Å for point-like sources. The ACS G800L images and matched direct images were reduced with an automatic pipeline that handles all steps from archive retrieval, alignment and astrometric calibration, direct image combination, catalogue generation, spectral extraction and collection of metadata. The large number of extracted spectra (73,581) demanded automatic methods for quality control and an automated classification algorithm was trained on the visual inspection of several thousand spectra. The final sample of quality controlled spectra includes 47 919 datasets (65% of the total number of extracted spectra) for 32 149 unique objects, with a median iAB-band magnitude of 23.7, reaching 26.5 AB for the faintest objects. Each released dataset contains science-ready 1D and 2D spectra, as well as multi-band image cutouts of corresponding sources and a useful preview page summarising the direct and slitless data, astrometric and photometric parameters. This release is part of the continuing effort to enhance the content of the Hubble Legacy Archive (HLA) with highly processed data products which significantly facilitate the scientific exploitation of the Hubble data. In order to characterize the slitless spectra, emission-line flux and equivalent width sensitivity of the ACS data were compared with public ground-based spectra in the GOODS-South field. An example list of emission line galaxies with two or more identified lines is also included, covering the redshift range 0.2 - 4.6. Almost all redshift determinations outside of the GOODS fields are new. The scope of science projects

  7. The distribution of polarized radio sources >15 μJy IN GOODS-N

    SciTech Connect

    Rudnick, L.; Owen, F. N.

    2014-04-10

    We present deep Very Large Array observations of the polarization of radio sources in the GOODS-N field at 1.4 GHz at resolutions of 1.''6 and 10''. At 1.''6, we find that the peak flux cumulative number count distribution is N(> p) ∼ 45*(p/30 μJy){sup –0.6} per square degree above a detection threshold of 14.5 μJy. This represents a break from the steeper slopes at higher flux densities, resulting in fewer sources predicted for future surveys with the Square Kilometer Array and its precursors. It provides a significant challenge for using background rotation measures (RMs) to study clusters of galaxies or individual galaxies. Most of the polarized sources are well above our detection limit, and they are also radio galaxies that are well-resolved even at 10'', with redshifts from ∼0.2-1.9. We determined a total polarized flux for each source by integrating the 10'' polarized intensity maps, as will be done by upcoming surveys such as POSSUM. These total polarized fluxes are a factor of two higher, on average, than the peak polarized flux at 1.''6; this would increase the number counts by ∼50% at a fixed flux level. The detected sources have RMs with a characteristic rms scatter of ∼11 rad m{sup –2} around the local Galactic value, after eliminating likely outliers. The median fractional polarization from all total intensity sources does not continue the trend of increasing at lower flux densities, as seen for stronger sources. The changes in the polarization characteristics seen at these low fluxes likely represent the increasing dominance of star-forming galaxies.

  8. Models for Deploying Open Source and Commercial Software to Support Earth Science Data Processing and Distribution

    NASA Astrophysics Data System (ADS)

    Yetman, G.; Downs, R. R.

    2011-12-01

    Software deployment is needed to process and distribute scientific data throughout the data lifecycle. Developing software in-house can take software development teams away from other software development projects and can require efforts to maintain the software over time. Adopting and reusing software and system modules that have been previously developed by others can reduce in-house software development and maintenance costs and can contribute to the quality of the system being developed. A variety of models are available for reusing and deploying software and systems that have been developed by others. These deployment models include open source software, vendor-supported open source software, commercial software, and combinations of these approaches. Deployment in Earth science data processing and distribution has demonstrated the advantages and drawbacks of each model. Deploying open source software offers advantages for developing and maintaining scientific data processing systems and applications. By joining an open source community that is developing a particular system module or application, a scientific data processing team can contribute to aspects of the software development without having to commit to developing the software alone. Communities of interested developers can share the work while focusing on activities that utilize in-house expertise and addresses internal requirements. Maintenance is also shared by members of the community. Deploying vendor-supported open source software offers similar advantages to open source software. However, by procuring the services of a vendor, the in-house team can rely on the vendor to provide, install, and maintain the software over time. Vendor-supported open source software may be ideal for teams that recognize the value of an open source software component or application and would like to contribute to the effort, but do not have the time or expertise to contribute extensively. Vendor-supported software may

  9. The AC photovoltaic module is here!

    NASA Astrophysics Data System (ADS)

    Strong, Steven J.; Wohlgemuth, John H.; Wills, Robert H.

    1997-02-01

    This paper describes the design, development, and performance results of a large-area photovoltaic module whose electrical output is ac power suitable for direct connection to the utility grid. The large-area ac PV module features a dedicated, integrally mounted, high-efficiency dc-to-ac power inverter with a nominal output of 250 watts (STC) at 120 Vac, 60 H, that is fully compatible with utility power. The module's output is connected directly to the building's conventional ac distribution system without need for any dc wiring, string combiners, dc ground-fault protection or additional power-conditioning equipment. With its advantages, the ac photovoltaic module promises to become a universal building block for use in all utility-interactive PV systems. This paper discusses AC Module design aspects and utility interface issues (including islanding).

  10. Residues, Distributions, Sources, and Ecological Risks of OCPs in the Water from Lake Chaohu, China

    PubMed Central

    Liu, Wen-Xiu; He, Wei; Qin, Ning; Kong, Xiang-Zhen; He, Qi-Shuang; Ouyang, Hui-Ling; Yang, Bin; Wang, Qing-Mei; Yang, Chen; Jiang, Yu-Jiao; Wu, Wen-Jing; Xu, Fu-Liu

    2012-01-01

    The levels of 18 organochlorine pesticides (OCPs) in the water from Lake Chaohu were measured by a solid phase extraction-gas chromatography-mass spectrometer detector. The spatial and temporal distribution, possible sources, and potential ecological risks of the OCPs were analyzed. The annual mean concentration for the OCPs in Lake Chaohu was 6.99 ng/L. Aldrin, HCHs, and DDTs accounted for large proportions of the OCPs. The spatial pollution followed the order of Central Lakes > Western Lakes > Eastern Lakes and water area. The sources of the HCHs were mainly from the historical usage of lindane. DDTs were degraded under aerobic conditions, and the main sources were from the use of technical DDTs. The ecological risks of 5 OCPs were assessed by the species sensitivity distribution (SSD) method in the order of heptachlor > γ-HCH > p,p′-DDT > aldrin > endrin. The combining risks of all sampling sites were MS > JC > ZM > TX, and those of different species were crustaceans > fish > insects and spiders. Overall, the ecological risks of OCP contaminants on aquatic animals were very low. PMID:23251107

  11. Organic micropollutants in coastal waters from NW Mediterranean Sea: sources distribution and potential risk.

    PubMed

    Sánchez-Avila, Juan; Tauler, Romà; Lacorte, Silvia

    2012-10-01

    This study provides a first estimation on the sources, distribution and risk of organic micropollutants (OMPs) in coastal waters from NW Mediterranean Sea. Polycyclic aromatic hydrocarbons, polychlorinated biphenyls, organochlorinated pesticides, polybrominated diphenyl ethers, phthalates and alkylphenols were analyzed by solid phase extraction and gas chromatography coupled to tandem mass spectrometry (SPE-GC-EI-MS/MS). River waters and wastewater treatment plant effluents discharging to the sea were identified as the main sources of OMPs to coastal waters, with an estimated input amount of around of 25,800 g d(-1). The concentration of ΣOMPs in coastal areas ranged from 17.4 to 8442 ng L(-1), and was the highest in port waters, followed by coastal and river mouth seawaters. A summarized overview of the patterns and sources of OMP contamination on the investigated coastal sea waters of NW Mediterranean Sea, as well as of their geographical distribution was obtained by Principal Component Analysis of the complete data set after its adequate pretreatment. Alkylphenols, bisphenol A and phthalates were the main contributors to ΣOMPs and produced an estimated significant pollution risk for fish, algae and the sensitive mysid shrimp organisms in seawater samples. The combination of GC-MS/MS, chemometrics and risk analysis is proven to be useful for a better control and management of OMP discharges. PMID:22706016

  12. Distribution and geological sources of selenium in environmental materials in Taoyuan County, Hunan Province, China.

    PubMed

    Ni, Runxiang; Luo, Kunli; Tian, Xinglei; Yan, Songgui; Zhong, Jitai; Liu, Maoqiu

    2016-06-01

    The selenium (Se) distribution and geological sources in Taoyuan County, China, were determined by using hydride generation atomic fluorescence spectrometry on rock, soil, and food crop samples collected from various geological regions within the county. The results show Se contents of 0.02-223.85, 0.18-7.05, and 0.006-5.374 mg/kg in the rock, soil, and food crops in Taoyuan County, respectively. The region showing the highest Se content is western Taoyuan County amid the Lower Cambrian and Ediacaran black rock series outcrop, which has banding distributed west to east. A relatively high-Se environment is found in the central and southern areas of Taoyuan County, where Quaternary Limnetic sedimentary facies and Neoproterozoic metamorphic volcanic rocks outcrop, respectively. A relatively low-Se environment includes the central and northern areas of Taoyuan County, where Middle and Upper Cambrian and Ordovician carbonate rocks and Cretaceous sandstones and conglomerates outcrop. These results indicate that Se distribution in Taoyuan County varies markedly and is controlled by the Se content of the bedrock. The Se-enriched Lower Cambrian and Ediacaran black rock series is the primary source of the seleniferous environment observed in Taoyuan County. Potential seleniferous environments are likely to be found near outcrops of the Lower Cambrian and Ediacaran black rock series in southern China. PMID:26563208

  13. Aerosol structure and vertical distribution in a multi-source dust region.

    PubMed

    Zhang, Jie; Zhang, Qiang; Tang, Congguo; Han, Yongxiang

    2012-01-01

    The vertical distribution of aerosols was directly observed under various atmospheric conditions in the free troposphere using surface micro-pulse lidar (MPL4) at the Zhangye Station (39.08 degrees N, 100.27 degrees E) in western China in the spring of 2008. The study shows that the aerosol distribution over Zhangye can be vertically classified into upper, middle and lower layers with altitudes of 4.5 to 9 km, 2.5 to 4.5 km, and less than 2.5 km, respectively. The aerosol in the upper layer originated from the external sources at higher altitude regions, from far desert regions upwind of Zhangye or transported from higher atmospheric layers by free convection, and the altitude of this aerosol layer decreased with time; the aerosols in the middle and lower layers originated from both external and local sources. The aerosol extinction coefficients in the upper and lower layers decreased with altitude, whereas the coefficient in the middle layer changed only slightly, which suggests that aerosol mixing occurs in the middle layer. The distribution of aerosols with altitude has three features: a single peak that forms under stable atmospheric conditions, an exponential decrease with altitude that occurs under unstable atmospheric conditions, and slight change in the mixed layer. Due to the impact of the top of the atmospheric boundary layer, the diurnal variation in the aerosol extinction coefficient has a single peak, which is higher in the afternoon and lower in the morning. PMID:23513689

  14. Wall-loss distribution of charge breeding ions in an electron cyclotron resonance ion source

    SciTech Connect

    Jeong, S. C.; Oyaizu, M.; Imai, N.; Hirayama, Y.; Ishiyama, H.; Miyatake, H.; Niki, K.; Okada, M.; Watanabe, Y. X.; Otokawa, Y.; Osa, A.; Ichikawa, S.

    2011-03-15

    The ion loss distribution in an electron cyclotron resonance ion source (ECRIS) was investigated to understand the element dependence of the charge breeding efficiency in an electron cyclotron resonance (ECR) charge breeder. The radioactive {sup 111}In{sup 1+} and {sup 140}Xe{sup 1+} ions (typical nonvolatile and volatile elements, respectively) were injected into the ECR charge breeder at the Tokai Radioactive Ion Accelerator Complex to breed their charge states. Their respective residual activities on the sidewall of the cylindrical plasma chamber of the source were measured after charge breeding as functions of the azimuthal angle and longitudinal position and two-dimensional distributions of ions lost during charge breeding in the ECRIS were obtained. These distributions had different azimuthal symmetries. The origins of these different azimuthal symmetries are qualitatively discussed by analyzing the differences and similarities in the observed wall-loss patterns. The implications for improving the charge breeding efficiencies of nonvolatile elements in ECR charge breeders are described. The similarities represent universal ion loss characteristics in an ECR charge breeder, which are different from the loss patterns of electrons on the ECRIS wall.

  15. Inferring the Spatial and Energy Distribution of Gamma-Ray Burst Sources. II. Isotropic Models

    NASA Astrophysics Data System (ADS)

    Loredo, Thomas J.; Wasserman, Ira M.

    1998-07-01

    We use Bayesian methods to analyze the distribution of gamma-ray burst intensities reported in the Third BATSE Catalog (3B catalog) of gamma-ray bursts, presuming the distribution of burst sources (``bursters'') is isotropic. We study both phenomenological and cosmological source distribution models, using Bayes's theorem both to infer unknown parameters in the models and to compare rival models. We analyze the distribution of the time-averaged peak photon number flux, Φ, measured on both 64 ms and 1024 ms timescales, performing the analysis of data based on each timescale independently. Several of our findings differ from those of previous analyses that modeled burst detection less completely. In particular, we find that the width of the intrinsic luminosity function for bursters is unconstrained, and the luminosity function of the actually observed bursts can be extremely broad, in contrast to the findings of all previous studies. Useful constraints probably require observation of bursts significantly fainter than those visible to BATSE. We also find that the 3B peak flux data do not usefully constrain the redshifts of burst sources; useful constraints require the analysis of data beyond that in the 3B catalog (such as burst time histories) or data from brighter bursts than have been seen by BATSE (such as those observed by the Pioneer Venus Orbiter). In addition, we find that an accurate understanding of the peak flux distributions reported in the 3B almost certainly requires consideration of data on the temporal and spectral properties of bursts beyond that reported in the 3B catalog and more sophisticated modeling than has so far been attempted. We first analyze purely phenomenological power-law and broken power-law models for the distribution of observed peak fluxes. We find that the 64 ms data are adequately fitted by a single power law, but that the 1024 ms data significantly favor models with a sharp, steep break near the highest observed fluxes. At

  16. AC/DC Power Systems with Applications for future Lunar/Mars base and Crew Exploration Vehicle

    NASA Technical Reports Server (NTRS)

    Chowdhury, Badrul H.

    2005-01-01

    ABSTRACT The Power Systems branch at JSC faces a number of complex issues as it readies itself for the President's initiative on future space exploration beyond low earth orbit. Some of these preliminary issues - those dealing with electric power generation and distribution on board Mars-bound vehicle and that on Lunar and Martian surface may be summarized as follows: Type of prime mover - Because solar power may not be readily available on parts of the Lunar/Mars surface and also during the long duration flight to Mars, the primary source of power will most likely be nuclear power (Uranium fuel rods) with a secondary source of fuel cell (Hydrogen supply). The electric power generation source - With nuclear power being the main prime mover, the electric power generation source will most likely be an ac generator at a yet to be determined frequency. Thus, a critical issue is whether the generator should generate at constant or variable frequency. This will decide what type of generator to use - whether it is a synchronous machine, an asynchronous induction machine or a switched reluctance machine. The type of power distribution system - the distribution frequency, number of wires (3- wire, 4-wire or higher), and ac/dc hybridization. Building redundancy and fault tolerance in the generation and distribution sub-systems so that the system is safe; provides 100% availability to critical loads; continues to operate even with faulted sub-systems; and requires minimal maintenance. This report descril_es results of a summer faculty fellowship spent in the Power Systems Branch with the specific aim of investigating some of the lessons learned in electric power generation and usage from the terrestrial power systems industry, the aerospace industry as well as NASA's on-going missions so as to recommend novel surface and vehicle-based power systems architectures in support of future space exploration initiatives. A hybrid ac/dc architecture with source side and load side

  17. Required distribution of noise sources for Green's function recovery in diffusive fields

    NASA Astrophysics Data System (ADS)

    Shamsalsadati, S.; Weiss, C. J.

    2011-12-01

    In the most general sense, noise is the part of the signal of little or no interest, due to a multitude of reasons such as operator error, imperfect instrumentation, experiment design, or inescapable background interference. Considering the latter, it has been shown that Green's function can be extracted from cross-correlation of the ambient, diffusive wavefields arising from background random noise sources. Pore pressure and low-frequency electromagnetic induction are two such examples of diffusive fields. In theory, applying Green's function method in geophysical exploration requires infinity of volumetrically distributed sources; however, in the real world the number of noise sources in an area is limited, and furthermore, unevenly distributed in time, space and spectral content. Hence, quantification of the requisite noise sources that enable us to calculate Green's function acceptably well remains an open research question. The purpose of this study is to find the area of noise sources that contribute most to the Green's function estimation in diffusive systems. We call such a region the Volume of Relevance (VoR). Our analysis builds upon recent work in 1D homogeneous system where it was shown that sources located between two receivers positions are the most important ones for the purpose of Green's function recovery. Our results confirm the previous finding but we also examine the effect of heterogeneity, dimensionality and receiver location in both 1D and 2D at a fixed frequency. We demonstrate that for receivers located symmetrically across an interface between regions of contrasting diffusivity, the VoR rapidly shifts from one side of the interface to the other, and back again, as receiver separation increases. We also demonstrate that where the receiver pair is located on the interface itself, the shifting is less rapid, and for moderate to high diffusivity contrasts, the VoR remains entirely on the more diffusive side. In addition, because classical

  18. A methodology for quantitatively estimating a distributed source of volatiles in a cometary coma

    NASA Astrophysics Data System (ADS)

    De Keyser, Johan; Dhooghe, Frederik; Gunell, Herbert; Maggiolo, Romain; Mann, Ingrid

    2014-05-01

    Rosetta will rendez-vous with comet 67P/Churyumov-Gerasimenko in May 2014. One of its objectives is to study the gas in the cometary coma. The Rosetta Orbiter Spectrometer for Ion and Neutral Analysis (ROSINA) package aims to determine the gas composition in the coma, in particular during the planned close flyby episodes. An outstanding question - since earlier findings by Giotto at 1P/Halley - is the role of outgassing from dust particles. The gas in the coma mainly originates from sublimation of volatiles on the nucleus surface, but additional sublimation from dust particles may contribute as well. The dust therefore provides a "distributed source" of such volatiles. In particular, outgassing from dust particles necessarily will lead to different radial profiles of the sublimated gas and/or its photo-dissociation products, and through chemical reactions it may affect many other species. In the present contribution we demonstrate how information about the dust source can be inferred from the measured abundance of species in the coma, preferably over a range of distances from the nucleus. This is achieved by solving an inverse problem that is based on knowledge of the reaction pathways, the solar UV flux, and the coma measurements. The detailed characteristics of the distributed source depend on the dust grain size distribution, the outgassing rate, the possibly different composition of the volatile material carried by the grains, the dust grain outflow velocities, and dust grain fragmentation. The proposed methodology is limited in determining these characteristics, but it can be refined or constrained by incorporating information, for instance, provided by the dust instruments on board Rosetta.

  19. Propagation of Source Grain-size Distribution Uncertainty by Using a Lagrangian Volcanic Particle Dispersal Model

    NASA Astrophysics Data System (ADS)

    Neri, A.; De'Michieli Vitturi, M.; Pardini, F.; Salvetti, M. V.; Spanu, A.

    2014-12-01

    Lagrangian particle dispersal models are commonly used for tracking ash particles emitted from volcanic plumes and transported under the action of atmospheric wind fields. In this work, we adopted a Lagrangian particle model to carry out an uncertainty quantification analysis of volcanic ash dispersal in the atmosphere focused on the uncertainties affecting particle source conditions. To this aim the Eulerian fully compressible mesoscale non-hydrostatic model WRF was used to generate the driving wind field. The Lagrangian particle model LPAC (de'Michieli Vitturi et al., JGR 2010) was then used to simulate the transport of mass particles under the action of atmospheric conditions. The particle motion equations were derived by expressing the Lagrangian particle acceleration as the sum of the forces acting along its trajectory, with drag forces calculated as a function of particle diameter, density, shape and Reynolds number. The simulations were representative of weak plume events of Mt. Etna and aimed to quantify the effect on the dispersal process of the uncertainty in the mean and variance of a Gaussian density function describing the grain-size distribution of the mixture and in the particle sphericity. In order to analyze the sensitivity of particle dispersal to these uncertain parameters with a reasonable number of simulations, and therefore with affordable computational costs, response surfaces in the parameter space were built by using the generalized polynomial chaos technique. The uncertainty analysis allowed to quantify the most probable values, as well as their pdf, of the number of particles as well as of the mean and variance of the grain size distribution at various distances from the source, both in air and on the ground. In particular, results highlighted the strong reduction of the uncertainty ranges of the mean and variance of the grain-size distribution with increasing distance from source and the significant control of particle sphericity on the

  20. Anthropogenic {sup 129}I in western New York: Distribution, sources and pathways

    SciTech Connect

    Fehn, U.; Rao, U.; Teng, R.T.D.

    1995-12-01

    The present {sup 129}I concentration at the surface of the earth is dominated by releases from anthropogenic sources such as atmospheric weapons tests and nuclear facilities. We report here {sup 129}I concentrations in waters, plants and soils from Western New York and the surrounding areas. Values found in waters and plants outside Western New York are approximately three orders of magnitude above natural levels. Concentrations in Western New York are another order of magnitude higher with a distinct pattern of concentration pointing to the source at West Valley, a former reprocessing facility, which continues to add significantly to the {sup 129}I budget in this region. Transport of anthropogenic {sup 129}I is clearly detectable in waters draining the West Valley area but the overall distribution of this isotope indicates also a significant component of aerial transport. The continued presence of bomb-related {sup 129}I demonstrates a long residence time of this isotope in biosphere and hydrosphere.

  1. Long distance measurement-device-independent quantum key distribution with entangled photon sources

    SciTech Connect

    Xu, Feihu; Qi, Bing; Liao, Zhongfa; Lo, Hoi-Kwong

    2013-08-05

    We present a feasible method that can make quantum key distribution (QKD), both ultra-long-distance and immune, to all attacks in the detection system. This method is called measurement-device-independent QKD (MDI-QKD) with entangled photon sources in the middle. By proposing a model and simulating a QKD experiment, we find that MDI-QKD with one entangled photon source can tolerate 77 dB loss (367 km standard fiber) in the asymptotic limit and 60 dB loss (286 km standard fiber) in the finite-key case with state-of-the-art detectors. Our general model can also be applied to other non-QKD experiments involving entanglement and Bell state measurements.

  2. Photon-monitoring attack on continuous-variable quantum key distribution with source in middle

    NASA Astrophysics Data System (ADS)

    Wang, Yijun; Huang, Peng; Guo, Ying; Huang, Dazu

    2014-12-01

    Motivated by a fact that the non-Gaussian operation may increase entanglement of an entangled system, we suggest a photon-monitoring attack strategy in the entanglement-based (EB) continuous-variable quantum key distribution (CVQKD) using the photon subtraction operations, where the entangled source originates from the center instead of one of the legal participants. It shows that an eavesdropper, Eve, can steal large information from participants after intercepting the partial beams with the photon-monitoring attach strategy. The structure of the proposed CVQKD protocol is useful in simply analyzing how quantum loss in imperfect channels can decrease the performance of the CVQKD protocol. The proposed attack strategy can be implemented under current technology, where a newly developed and versatile no-Gaussian operation can be well employed with the entangled source in middle in order to access to mass information in the EB CVQKD protocol, as well as in the prepare-and-measure (PM) CVQKD protocol.

  3. Distribution, richness, quality, and thermal maturity of source rock units on the North Slope of Alaska

    USGS Publications Warehouse

    Peters, K.E.; Bird, K.J.; Keller, M.A.; Lillis, P.G.; Magoon, L.B.

    2003-01-01

    Four source rock units on the North Slope were identified, characterized, and mapped to better understand the origin of petroleum in the area: Hue-gamma ray zone (Hue-GRZ), pebble shale unit, Kingak Shale, and Shublik Formation. Rock-Eval pyrolysis, total organic carbon analysis, and well logs were used to map the present-day thickness, organic quantity (TOC), quality (hydrogen index, HI), and thermal maturity (Tmax) of each unit. To map these units, we screened all available geochemical data for wells in the study area and assumed that the top and bottom of the oil window occur at Tmax of ~440° and 470°C, respectively. Based on several assumptions related to carbon mass balance and regional distributions of TOC, the present-day source rock quantity and quality maps were used to determine the extent of fractional conversion of the kerogen to petroleum and to map the original organic richness prior to thermal maturation.

  4. A directional array approach for the measurement of rotor noise source distributions with controlled spatial resolution

    NASA Technical Reports Server (NTRS)

    Brooks, T. F.; Marcolini, M. A.; Pope, D. S.

    1987-01-01

    A special array system has been designed to examine noise source distributions over a helicopter rotor model. The particular measurement environment is for a rotor operating in the open jet of an anechoic wind tunnel. An out-of-flow directional microphone element array is used with a directivity pattern whose major directional lobe projects on the rotor disk. If significant contributions from extraneous tunnel noise sources in the direction of the side lobes are excluded, the dominant output from the array would be that noise emitted from the projected area on the rotor disk. The design incorporates an array element signal blending features which serves to control the spatial resolution of the size of the directional lobes. (Without blending, the resolution and side lobe size are very strong functions of frequency, which severely limits the array's usefulness).

  5. Transverse distribution of beam current oscillations of a 14 GHz electron cyclotron resonance ion source.

    PubMed

    Tarvainen, O; Toivanen, V; Komppula, J; Kalvas, T; Koivisto, H

    2014-02-01

    The temporal stability of oxygen ion beams has been studied with the 14 GHz A-ECR at JYFL (University of Jyvaskyla, Department of Physics). A sector Faraday cup was employed to measure the distribution of the beam current oscillations across the beam profile. The spatial and temporal characteristics of two different oscillation "modes" often observed with the JYFL 14 GHz ECRIS are discussed. It was observed that the low frequency oscillations below 200 Hz are distributed almost uniformly. In the high frequency oscillation "mode," with frequencies >300 Hz at the core of the beam, carrying most of the current, oscillates with smaller amplitude than the peripheral parts of the beam. The results help to explain differences observed between the two oscillation modes in terms of the transport efficiency through the JYFL K-130 cyclotron. The dependence of the oscillation pattern on ion source parameters is a strong indication that the mechanisms driving the fluctuations are plasma effects. PMID:24593488

  6. Finite-key security analysis of quantum key distribution with imperfect light sources

    NASA Astrophysics Data System (ADS)

    Mizutani, Akihiro; Curty, Marcos; Lim, Charles Ci Wen; Imoto, Nobuyuki; Tamaki, Kiyoshi

    2015-09-01

    In recent years, the gap between theory and practice in quantum key distribution (QKD) has been significantly narrowed, particularly for QKD systems with arbitrarily flawed optical receivers. The status for QKD systems with imperfect light sources is however less satisfactory, in the sense that the resulting secure key rates are often overly dependent on the quality of state preparation. This is especially the case when the channel loss is high. Very recently, to overcome this limitation, Tamaki et al proposed a QKD protocol based on the so-called ‘rejected data analysis’, and showed that its security—in the limit of infinitely long keys—is almost independent of any encoding flaw in the qubit space, being this protocol compatible with the decoy state method. Here, as a step towards practical QKD, we show that a similar conclusion is reached in the finite-key regime, even when the intensity of the light source is unstable. More concretely, we derive security bounds for a wide class of realistic light sources and show that the bounds are also efficient in the presence of high channel loss. Our results strongly suggest the feasibility of long distance provably secure communication with imperfect light sources.

  7. Finite-key security analysis of quantum key distribution with imperfect light sources

    SciTech Connect

    Mizutani, Akihiro; Curty, Marcos; Lim, Charles Ci Wen; Imoto, Nobuyuki; Tamaki, Kiyoshi

    2015-09-09

    In recent years, the gap between theory and practice in quantum key distribution (QKD) has been significantly narrowed, particularly for QKD systems with arbitrarily flawed optical receivers. The status for QKD systems with imperfect light sources is however less satisfactory, in the sense that the resulting secure key rates are often overly dependent on the quality of state preparation. This is especially the case when the channel loss is high. Very recently, to overcome this limitation, Tamaki et al proposed a QKD protocol based on the so-called 'rejected data analysis', and showed that its security in the limit of infinitely long keys is almost independent of any encoding flaw in the qubit space, being this protocol compatible with the decoy state method. Here, as a step towards practical QKD, we show that a similar conclusion is reached in the finite-key regime, even when the intensity of the light source is unstable. More concretely, we derive security bounds for a wide class of realistic light sources and show that the bounds are also efficient in the presence of high channel loss. Our results strongly suggest the feasibility of long distance provably secure communication with imperfect light sources.

  8. Space-bound optical source for satellite-ground decoy-state quantum key distribution.

    PubMed

    Li, Yang; Liao, Sheng-Kai; Chen, Xie-Le; Chen, Wei; Cheng, Kun; Cao, Yuan; Yong, Hai-Lin; Wang, Tao; Yang, Hua-Qiang; Liu, Wei-Yue; Yin, Juan; Liang, Hao; Peng, Cheng-Zhi; Pan, Jian-Wei

    2014-11-01

    Satellite-ground quantum key distribution has embarked on the stage of engineering implementation, and a global quantum-secured network is imminent in the foreseeable future. As one payload of the quantum-science satellite which will be ready before the end of 2015, we report our recent work of the space-bound decoy-state optical source. Specialized 850 nm laser diodes have been manufactured and the integrated optical source has gotten accomplished based on these LDs. The weak coherent pulses produced by our optical source feature a high clock rate of 100 MHz, intensity stability of 99.5%, high polarization fidelity of 99.7% and phase randomization. A series of space environment tests have been conducted to verify the optical source's performance and the results are satisfactory. The emulated final secure keys are about 120 kbits during one usable pass of the low Earth orbit satellite. This work takes a significant step forward towards satellite-ground QKD and the global quantum-secured network. PMID:25401878

  9. Finite-key security analysis of quantum key distribution with imperfect light sources

    DOE PAGESBeta

    Mizutani, Akihiro; Curty, Marcos; Lim, Charles Ci Wen; Imoto, Nobuyuki; Tamaki, Kiyoshi

    2015-09-09

    In recent years, the gap between theory and practice in quantum key distribution (QKD) has been significantly narrowed, particularly for QKD systems with arbitrarily flawed optical receivers. The status for QKD systems with imperfect light sources is however less satisfactory, in the sense that the resulting secure key rates are often overly dependent on the quality of state preparation. This is especially the case when the channel loss is high. Very recently, to overcome this limitation, Tamaki et al proposed a QKD protocol based on the so-called 'rejected data analysis', and showed that its security in the limit of infinitelymore » long keys is almost independent of any encoding flaw in the qubit space, being this protocol compatible with the decoy state method. Here, as a step towards practical QKD, we show that a similar conclusion is reached in the finite-key regime, even when the intensity of the light source is unstable. More concretely, we derive security bounds for a wide class of realistic light sources and show that the bounds are also efficient in the presence of high channel loss. Our results strongly suggest the feasibility of long distance provably secure communication with imperfect light sources.« less

  10. Co Spectral Line Energy Distributions in Orion Sources: Templates for Extragalactic Observations

    NASA Astrophysics Data System (ADS)

    Indriolo, Nick; Bergin, Edwin

    2015-06-01

    The Herschel Space Observatory has enabled the observation of CO emission lines originating in the J=5 through J=48 rotational levels. Surveys of active galaxies (e.g., starbursts, Seyferts, ULIRGs) detect emission from levels as high as J=30, but the precise excitation mechanisms responsible for producing the observed CO SLEDs (Spectral Line Energy Distribution) remain ambiguous. To better constrain the possible excitation mechanisms in extragalactic sources, we investigate the CO SLEDs arising from sources with known characteristics in the nearby Orion region. Targets include Orion-KL (high-mass star forming region containing a hot core, embedded protostars, outflows, and shocks), Orion South (high-mass star forming region containing embedded protostars, outflows, and a photodissociation region), Orion H_2 Peak 1 (molecular shock), and the Orion Bar (a photodissociation region). Emission lines from complex sources are decomposed using velocity information from high spectral resolution observations made with Herschel-HIFI (Heterodyne Instrument for the Far-Infrared). Each source and/or component is taken as a template for a particular excitation mechanism, and then applied to interpret excitation in more distant regions within the Galaxy, as well as external galaxies.

  11. Distribution, sources and health risk assessment of mercury in kindergarten dust

    NASA Astrophysics Data System (ADS)

    Sun, Guangyi; Li, Zhonggen; Bi, Xiangyang; Chen, Yupeng; Lu, Shuangfang; Yuan, Xin

    2013-07-01

    Mercury (Hg) contamination in urban area is a hot issue in environmental research. In this study, the distribution, sources and health risk of Hg in dust from 69 kindergartens in Wuhan, China, were investigated. In comparison with most other cities, the concentrations of total mercury (THg) and methylmercury (MeHg) were significantly elevated, ranging from 0.15 to 10.59 mg kg-1 and from 0.64 to 3.88 μg kg-1, respectively. Among the five different urban areas, the educational area had the highest concentrations of THg and MeHg. The GIS mapping was used to identify the hot-spot areas and assess the potential pollution sources of Hg. The emissions of coal-power plants and coking plants were the main sources of THg in the dust, whereas the contributions of municipal solid waste (MSW) landfills and iron and steel smelting related industries were not significant. However, the emission of MSW landfills was considered to be an important source of MeHg in the studied area. The result of health risk assessment indicated that there was a high adverse health effect of the kindergarten dust in terms of Hg contamination on the children living in the educational area (Hazard index (HI) = 6.89).

  12. Plans for a Collaboratively Developed Distributed Control System for the Spallation Neutron Source

    SciTech Connect

    DeVan, W.R.; Gurd, D.P.; Hammonds, J.; Lewis, S.A.; Smith, J.D.

    1999-03-29

    The Spallation Neutron Source (SNS) is an accelerator-based pulsed neutron source to be built in Oak Ridge, Tennessee. The facility has five major sections - a ''front end'' consisting of a 65 keV H{sup -} ion source followed by a 2.5 MeV RFQ; a 1 GeV linac; a storage ring; a 1MW spallation neutron target (upgradeable to 2 MW); the conventional facilities to support these machines and a suite of neutron scattering instruments to exploit them. These components will be designed and implemented by five collaborating institutions: Lawrence Berkeley National Laboratory (Front End), Los Alamos National Laboratory (Linac); Brookhaven National Laboratory (Storage Ring); Argonne National Laboratory (Instruments); and Oak Ridge National Laboratory (Neutron Source and Conventional Facilities). It is proposed to implement a fully integrated control system for all aspects of this complex. The system will be developed collaboratively, with some degree of local autonomy for distributed systems, but centralized accountability. Technical integration will be based upon the widely-used EPICS control system toolkit, and a complete set of hardware and software standards. The scope of the integrated control system includes site-wide timing and synchronization, networking and machine protection. This paper discusses the technical and organizational issues of planning a large control system to be developed collaboratively at five different institutions, the approaches being taken to address those issues, as well as some of the particular technical challenges for the SNS control system.

  13. Fast optical source for quantum key distribution based on semiconductor optical amplifiers.

    PubMed

    Jofre, M; Gardelein, A; Anzolin, G; Amaya, W; Capmany, J; Ursin, R; Peñate, L; Lopez, D; San Juan, J L; Carrasco, J A; Garcia, F; Torcal-Milla, F J; Sanchez-Brea, L M; Bernabeu, E; Perdigues, J M; Jennewein, T; Torres, J P; Mitchell, M W; Pruneri, V

    2011-02-28

    A novel integrated optical source capable of emitting faint pulses with different polarization states and with different intensity levels at 100 MHz has been developed. The source relies on a single laser diode followed by four semiconductor optical amplifiers and thin film polarizers, connected through a fiber network. The use of a single laser ensures high level of indistinguishability in time and spectrum of the pulses for the four different polarizations and three different levels of intensity. The applicability of the source is demonstrated in the lab through a free space quantum key distribution experiment which makes use of the decoy state BB84 protocol. We achieved a lower bound secure key rate of the order of 3.64 Mbps and a quantum bit error ratio as low as 1.14×10⁻² while the lower bound secure key rate became 187 bps for an equivalent attenuation of 35 dB. To our knowledge, this is the fastest polarization encoded QKD system which has been reported so far. The performance, reduced size, low power consumption and the fact that the components used can be space qualified make the source particularly suitable for secure satellite communication. PMID:21369207

  14. Electric Field Distribution Excited by Indoor Radio Source for Exposure Compliance Assessment

    NASA Astrophysics Data System (ADS)

    Higashiyama, Junji; Tarusawa, Yoshiaki

    Correction factors are presented for estimating the RF electromagnetic field strength in the compliance assessment of human exposure from an indoor RF radio source in the frequency range from 800MHz to 3.5GHz. The correction factors are derived from the increase in the spatial average electric field strength distribution, which is dependent on the building materials. The spatial average electric field strength is calculated using relative complex dielectric constants of building materials. The relative complex dielectric constant is obtained through measurement of the transmission and reflection losses for eleven kinds of building materials used in business office buildings and single family dwellings.

  15. An open source platform for multi-scale spatially distributed simulations of microbial ecosystems

    SciTech Connect

    Segre, Daniel

    2014-08-14

    The goal of this project was to develop a tool for facilitating simulation, validation and discovery of multiscale dynamical processes in microbial ecosystems. This led to the development of an open-source software platform for Computation Of Microbial Ecosystems in Time and Space (COMETS). COMETS performs spatially distributed time-dependent flux balance based simulations of microbial metabolism. Our plan involved building the software platform itself, calibrating and testing it through comparison with experimental data, and integrating simulations and experiments to address important open questions on the evolution and dynamics of cross-feeding interactions between microbial species.

  16. Rapid, high-order accurate calculation of flows due to free source or vortex distributions

    NASA Technical Reports Server (NTRS)

    Halsey, D.

    1981-01-01

    Fast Fourier transform (FFT) techniques are applied to the problem of finding the flow due to source or vortex distributions in the field outside an airfoil or other two-dimensional body. Either the complex potential or the complex velocity may be obtained to a high order of accuracy, with computational effort similar to that required by second-order fast Poisson solvers. These techniques are applicable to general flow problems with compressibility and rotation. An example is given of their use for inviscid compressible flow.

  17. Spatial distribution of old and emerging flame retardants in Chinese forest soils: sources, trends and processes.

    PubMed

    Zheng, Qian; Nizzetto, Luca; Li, Jun; Mulder, Marie D; Sáňka, Ondřej; Lammel, Gerhard; Bing, Haijian; Liu, Xin; Jiang, Yishan; Luo, Chunling; Zhang, Gan

    2015-03-01

    The levels and distribution of polybrominated diphenylethers (PBDEs), novel brominated flame retardants (NBFRs) and Dechlorane Plus (DP) in soils and their dependence on environmental and anthropological factors were investigated in 159 soil samples from 30 background forested mountain sites across China. Decabromodiphenylethane (DBDPE) was the most abundant flame retardant (25-18,000 pg g(-1) and 5-13,000 pg g(-1) in O-horizon and A-horizon, respectively), followed by BDE 209 (nd-5900 pg g(-1) and nd-2400 pg g(-1) in O-horizon and A-horizon, respectively). FRs distributions were primarily controlled by source distribution. The distributions of most phasing-out PBDEs, DP isomers and TBPH were in fact correlated to a population density-based index used as proxy of areas with elevated usage and waste of FR containing products. High concentrations of some NBFRs were however observed in industrialized regions and FR manufacturing plants. Strongly positive correlations were observed between PBDEs and their replacement products suggesting similar emission pattern and environmental behavior. Exposure of mineral subsoils depended on precipitations driving leaching of FRs into the soil core. This was especially evident for some emerging BFRs (TBE, TBPH, and TBB etc.) possibly indicating potential for diffuse groundwater contamination. PMID:25661400

  18. On Road Study of Colorado Front Range Greenhouse Gases Distribution and Sources

    NASA Astrophysics Data System (ADS)

    Petron, G.; Hirsch, A.; Trainer, M. K.; Karion, A.; Kofler, J.; Sweeney, C.; Andrews, A.; Kolodzey, W.; Miller, B. R.; Miller, L.; Montzka, S. A.; Kitzis, D. R.; Patrick, L.; Frost, G. J.; Ryerson, T. B.; Robers, J. M.; Tans, P.

    2008-12-01

    The Global Monitoring Division and Chemical Sciences Division of the NOAA Earth System Research Laboratory have teamed up over the summer 2008 to experiment with a new measurement strategy to characterize greenhouse gases distribution and sources in the Colorado Front Range. Combining expertise in greenhouse gases measurements and in local to regional scales air quality study intensive campaigns, we have built the 'Hybrid Lab'. A continuous CO2 and CH4 cavity ring down spectroscopic analyzer (Picarro, Inc.), a CO gas-filter correlation instrument (Thermo Environmental, Inc.) and a continuous UV absorption ozone monitor (2B Technologies, Inc., model 202SC) have been installed securely onboard a 2006 Toyota Prius Hybrid vehicle with an inlet bringing in outside air from a few meters above the ground. To better characterize point and distributed sources, air samples were taken with a Portable Flask Package (PFP) for later multiple species analysis in the lab. A GPS unit hooked up to the ozone analyzer and another one installed on the PFP kept track of our location allowing us to map measured concentrations on the driving route using Google Earth. The Hybrid Lab went out for several drives in the vicinity of the NOAA Boulder Atmospheric Observatory (BAO) tall tower located in Erie, CO and covering areas from Boulder, Denver, Longmont, Fort Collins and Greeley. Enhancements in CO2, CO and destruction of ozone mainly reflect emissions from traffic. Methane enhancements however are clearly correlated with nearby point sources (landfill, feedlot, natural gas compressor ...) or with larger scale air masses advected from the NE Colorado, where oil and gas drilling operations are widespread. The multiple species analysis (hydrocarbons, CFCs, HFCs) of the air samples collected along the way bring insightful information about the methane sources at play. We will present results of the analysis and interpretation of the Hybrid Lab Front Range Study and conclude with perspectives

  19. The occurrence and distribution of a group of organic micropollutants in Mexico City's water sources.

    PubMed

    Félix-Cañedo, Thania E; Durán-Álvarez, Juan C; Jiménez-Cisneros, Blanca

    2013-06-01

    The occurrence and distribution of a group of 17 organic micropollutants in surface and groundwater sources from Mexico City was determined. Water samples were taken from 7 wells, 4 dams and 15 tanks where surface and groundwater are mixed and stored before distribution. Results evidenced the occurrence of seven of the target compounds in groundwater: salicylic acid, diclofenac, di-2-ethylhexylphthalate (DEHP), butylbenzylphthalate (BBP), triclosan, bisphenol A (BPA) and 4-nonylphenol (4-NP). In surface water, 11 target pollutants were detected: same found in groundwater as well as naproxen, ibuprofen, ketoprofen and gemfibrozil. In groundwater, concentration ranges of salicylic acid, 4-NP and DEHP, the most frequently found compounds, were 1-464, 1-47 and 19-232 ng/L, respectively; while in surface water, these ranges were 29-309, 89-655 and 75-2,282 ng/L, respectively. Eleven target compounds were detected in mixed water. Concentrations in mixed water were higher than those determined in groundwater but lower than the detected in surface water. Different to that found in ground and surface water, the pesticide 2,4-D was found in mixed water, indicating that some pollutants can reach areas where they are not originally present in the local water sources. Concentration of the organic micropollutants found in this study showed similar to lower to those reported in water sources from developed countries. This study provides information that enriches the state of the art on the occurrence of organic micropollutants in water sources worldwide, notably in megacities of developing countries. PMID:23542484

  20. [Recent Distribution and Sources of Polycyclic Aromatic Hydrocarbons in Surface Soils from Yangtze River Delta].

    PubMed

    Li, Jing-ya; Wu, Di; Xu, Yun-song; Li, Xiang-dong; Wang, Xi-long; Zeng, Chao-hua; Fu, Xiao-fang; Liu, Wen-xin

    2016-01-15

    A total of 243 surface soil samples collected from 11 cities in the Yangtze River Delta region were analyzed for the concentrations, spatial distribution, component profiles and emission sources of 29 PAH species. The analytical results indicated the total concentrations of PAHs in Yangtze River Delta fell in the range from 21. 0 ng x g(-1) to 3 578.5 ng x g(-1) with an arithmetic mean and standard deviation of 310.6 ng x g(-1) and 459.1 ng x g(-1), respectively. Our data showed spatial distribution of PAHs concentrations varied greatly in the region. In addition, the contents of PAHs were positively correlated with the total organic carbon fractions in topsoil. The sites with the highest levels of PAHs in the 11 cities studied were located in Suzhou with 759.0 ng x g(-1) +/- 132.9 ng x g(-1) ollowed by the areas of Wuxi and Shanghai, with the total PAHs concentrations of 565. 3 ng x g(-1) +/- 705.5 ng x g(-1) and 349.4 ng g(-1) 220. 1 ng-g(-1) respectively. The profiles of different components pointed to a predominant role of the species with 2-4 rings, and especially for the low molecular weight components with 2-3 rings. A preliminary identification on emission sources of local PAHs was performed by the specific ratios of isomeric species and principal component analysis (PCA). The results designated industrial coal and biomass combustion as the main mixed emission sources of PAHs in surface soils from Yangtze River Delta, and tail gas from transport as another major source in some areas. PMID:27078965

  1. High resolution stationary digital breast tomosynthesis using distributed carbon nanotube x-ray source array

    SciTech Connect

    Qian Xin; Tucker, Andrew; Gidcumb, Emily; Shan Jing; Yang Guang; Calderon-Colon, Xiomara; Sultana, Shabana; Lu Jianping; Zhou, Otto; Spronk, Derrek; Sprenger, Frank; Zhang Yiheng; Kennedy, Don; Farbizio, Tom; Jing Zhenxue

    2012-04-15

    Purpose: The purpose of this study is to investigate the feasibility of increasing the system spatial resolution and scanning speed of Hologic Selenia Dimensions digital breast tomosynthesis (DBT) scanner by replacing the rotating mammography x-ray tube with a specially designed carbon nanotube (CNT) x-ray source array, which generates all the projection images needed for tomosynthesis reconstruction by electronically activating individual x-ray sources without any mechanical motion. The stationary digital breast tomosynthesis (s-DBT) design aims to (i) increase the system spatial resolution by eliminating image blurring due to x-ray tube motion and (ii) reduce the scanning time. Low spatial resolution and long scanning time are the two main technical limitations of current DBT technology. Methods: A CNT x-ray source array was designed and evaluated against a set of targeted system performance parameters. Simulations were performed to determine the maximum anode heat load at the desired focal spot size and to design the electron focusing optics. Field emission current from CNT cathode was measured for an extended period of time to determine the stable life time of CNT cathode for an expected clinical operation scenario. The source array was manufactured, tested, and integrated with a Selenia scanner. An electronic control unit was developed to interface the source array with the detection system and to scan and regulate x-ray beams. The performance of the s-DBT system was evaluated using physical phantoms. Results: The spatially distributed CNT x-ray source array comprised 31 individually addressable x-ray sources covering a 30 angular span with 1 pitch and an isotropic focal spot size of 0.6 mm at full width at half-maximum. Stable operation at 28 kV(peak) anode voltage and 38 mA tube current was demonstrated with extended lifetime and good source-to-source consistency. For the standard imaging protocol of 15 views over 14, 100 mAs dose, and 2 x 2 detector binning

  2. High resolution stationary digital breast tomosynthesis using distributed carbon nanotube x-ray source array

    PubMed Central

    Qian, Xin; Tucker, Andrew; Gidcumb, Emily; Shan, Jing; Yang, Guang; Calderon-Colon, Xiomara; Sultana, Shabana; Lu, Jianping; Zhou, Otto; Spronk, Derrek; Sprenger, Frank; Zhang, Yiheng; Kennedy, Don; Farbizio, Tom; Jing, Zhenxue

    2012-01-01

    Purpose: The purpose of this study is to investigate the feasibility of increasing the system spatial resolution and scanning speed of Hologic Selenia Dimensions digital breast tomosynthesis (DBT) scanner by replacing the rotating mammography x-ray tube with a specially designed carbon nanotube (CNT) x-ray source array, which generates all the projection images needed for tomosynthesis reconstruction by electronically activating individual x-ray sources without any mechanical motion. The stationary digital breast tomosynthesis (s-DBT) design aims to (i) increase the system spatial resolution by eliminating image blurring due to x-ray tube motion and (ii) reduce the scanning time. Low spatial resolution and long scanning time are the two main technical limitations of current DBT technology. Methods: A CNT x-ray source array was designed and evaluated against a set of targeted system performance parameters. Simulations were performed to determine the maximum anode heat load at the desired focal spot size and to design the electron focusing optics. Field emission current from CNT cathode was measured for an extended period of time to determine the stable life time of CNT cathode for an expected clinical operation scenario. The source array was manufactured, tested, and integrated with a Selenia scanner. An electronic control unit was developed to interface the source array with the detection system and to scan and regulate x-ray beams. The performance of the s-DBT system was evaluated using physical phantoms. Results: The spatially distributed CNT x-ray source array comprised 31 individually addressable x-ray sources covering a 30 angular span with 1 pitch and an isotropic focal spot size of 0.6 mm at full width at half-maximum. Stable operation at 28 kV(peak) anode voltage and 38 mA tube current was demonstrated with extended lifetime and good source-to-source consistency. For the standard imaging protocol of 15 views over 14, 100 mAs dose, and 2 × 2 detector

  3. Concordance between distributed EEG source localization and simultaneous EEG-fMRI studies of epileptic spikes.

    PubMed

    Grova, C; Daunizeau, J; Kobayashi, E; Bagshaw, A P; Lina, J-M; Dubeau, F; Gotman, J

    2008-01-15

    In order to analyze where epileptic spikes are generated, we assessed the level of concordance between EEG source localization using distributed source models and simultaneous EEG-fMRI which measures the hemodynamic correlates of EEG activity. Data to be compared were first estimated on the same cortical surface and two comparison strategies were used: (1) MEM-concordance: a comparison between EEG sources localized with the Maximum Entropy on the Mean (MEM) method and fMRI clusters showing a significant hemodynamic response. Minimal geodesic distances between local extrema and overlap measurements between spatial extents of EEG sources and fMRI clusters were used to quantify MEM-concordance. (2) fMRI-relevance: estimation of the fMRI-relevance index alpha quantifying if sources located in an fMRI cluster could explain some scalp EEG data, when this fMRI cluster was used to constrain the EEG inverse problem. Combining MEM-concordance and fMRI-relevance (alpha) indexes, each fMRI cluster showing a significant hemodynamic response (p<0.05 corrected) was classified according to its concordance with EEG data. Nine patients with focal epilepsy who underwent EEG-fMRI examination followed by EEG recording outside the scanner were selected for this study. Among the 62 fMRI clusters analyzed (7 patients), 15 (24%) found in 6 patients were highly concordant with EEG according to both MEM-concordance and fMRI-relevance. EEG concordance was found for 5 clusters (8%) according to alpha only, suggesting sources missed by the MEM. No concordance with EEG was found for 30 clusters (48%) and for 10 clusters (16%) alpha was significantly negative, suggesting EEG-fMRI discordance. We proposed two complementary strategies to assess and classify EEG-fMRI concordance. We showed that for most patients, part of the hemodynamic response to spikes was highly concordant with EEG sources, whereas other fMRI clusters in response to the same spikes were found distant or discordant with EEG

  4. Pu and 137Cs in the Yangtze River estuary sediments: distribution and source identification.

    PubMed

    Liu, Zhiyong; Zheng, Jian; Pan, Shaoming; Dong, Wei; Yamada, Masatoshi; Aono, Tatsuo; Guo, Qiuju

    2011-03-01

    Pu isotopes and (137)Cs were analyzed using sector field ICP-MS and γ spectrometry, respectively, in surface sediment and core sediment samples from the Yangtze River estuary. (239+240)Pu activity and (240)Pu/(239)Pu atom ratios (>0.18) shows a generally increasing trend from land to sea and from north to south in the estuary. This spatial distribution pattern indicates that the Pacific Proving Grounds (PPG) source Pu transported by ocean currents was intensively scavenged into the suspended sediment under favorable conditions, and mixed with riverine sediment as the water circulated in the estuary. This process is the main control for the distribution of Pu in the estuary. Moreover, Pu is also an important indicator for monitoring the changes of environmental radioactivity in the estuary as the river basin is currently the site of extensive human activities and the sea level is rising because of global climate changes. For core sediment samples the maximum peak of (239+240)Pu activity was observed at a depth of 172 cm. The sedimentation rate was estimated on the basis of the Pu maximum deposition peak in 1963-1964 to be 4.1 cm/a. The contributions of the PPG close-in fallout Pu (44%) and the riverine Pu (45%) in Yangtze River estuary sediments are equally important for the total Pu deposition in the estuary, which challenges the current hypothesis that the riverine Pu input was the major source of Pu budget in this area. PMID:21306104

  5. A review of sources, multimedia distribution and health risks of perfluoroalkyl acids (PFAAs) in China.

    PubMed

    Wang, Tieyu; Wang, Pei; Meng, Jing; Liu, Shijie; Lu, Yonglong; Khim, Jong Seong; Giesy, John P

    2015-06-01

    Perfluoroalkyl acids (PFAAs) have been recognized as emerging pollutants because of their ubiquitous occurrence in the environment, biota and humans. In order to investigate their sources, fate and environmental effects, a great number of surveys have been carried out over the past several years. In the present review, we summarized the status of sources and emission, concentration, distribution and risks of PFAAs in China. Concentrations of PFAAs, especially perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) in various environmental media including water, sediment, soil, rain, snow and organisms, as well as human tissues are summarized based on the available data. Concentrations of PFAAs in aquatic systems are higher in relatively more industrialized and urbanized areas than those from the less populated and remote regions in China, indicating that their emission and distribution are closely related to regional urbanization and industrialization. PFAAs and related products have been widely used over the past several decades, which have brought about high concentrations detected in environmental matrixes, biota and even local residents. Ecological risk assessment of PFAAs is still less developed in China. Most existing studies compared concentrations of PFAAs to guideline values derived for single species to evaluate the risk. In order to reveal the transport, partitioning and degradation of PFAAs in the environment, further studies on their behavior, fate, bioaccumulation and adverse effects in different trophic levels should be conducted. PMID:25262946

  6. Field Trial of Distributed Acoustic Sensing Using Active Sources at Garner Valley, California

    NASA Astrophysics Data System (ADS)

    Wang, H. F.; Lord, N. E.; Chalari, A.; Lancelle, C.; Baldwin, J. A.; Castongia, E.; Fratta, D.; Nigbor, R. L.; Karaulanov, R.

    2014-12-01

    An optical fiber Distributed Acoustic Sensor array was deployed in a shallow trench at the site of the Garner Valley Downhole Array (GVDA) in southern California. The site was operated as a collaborator of the Network for Earthquake Engineering Simulation (NEES) by UCSB. The fiber-optic cable layout approximated a rectangle whose dimensions were roughly 160 meters by 80 meters. The layout included two subdiagonals to provide a variety of orientations of the cable relative to source locations. The study included different seismic sources deployed at a number of surveyed positions: a 45 kN shear shaker operated at the site by NEES@UCLA, a portable 450 N shaker, a small Vibroseis truck, and hammer blows on a steel plate to map cable locations. Several dozen separate tests were recorded in which each test typically included ten repeats. The data were utilized for several studies. First, the characteristics of the recorded signals were analyzed for directivity and sensitivity of the cable response (Lancelle et al., 2014, this meeting). The DAS system recorded dynamic ground events in the direction of the cable and hence comparisons with geophones required signal processing. The one-meter spacing of DAS traces could be well correlated over distances of a few meters. Second, swept-sine sources were used to obtain surface-wave velocity dispersion to determine near-surface shear-wave velocity distribution using Multispectral Analysis of Surface Waves (MASW) (Baldwin et al., 2014, this meeting). The results were in good agreement with previous Vibroseis results at the site (Stokoe et al. 2004). Third, a new method for time-frequency filtering was developed for extracting the surface-wave phase velocities from uncorrelated receiver traces (Lord et al., 2014, this meeting).

  7. Distribution and sources of oxygenated non-hydrocarbons in topsoil of Beijing, China.

    PubMed

    Zhang, Zhihuan; Wan, Tiantian; Peng, Xuyang; He, Guangxiu; Liu, Yu; Zeng, Li

    2016-08-01

    The oxygenated non-hydrocarbon compounds are widely distributed in soil. To investigate the distribution and origin of these compounds in topsoil of Beijing, their contents and compositions were measured in topsoil from 62 sites in Beijing. The research results showed that oxygenated non-hydrocarbons were composed primarily of C6∼C28 n-fatty acids, C12∼C28 n-fatty alcohols, n-fatty acid methyl esters, phthalates, sterols, and dehydroabietic acid in the topsoil of Beijing. The contents and compositions of these compounds varied with the sampling site. The concentrations of n-fatty acids and phthalate esters were the highest at all sites, followed by sterols, n-fatty acid methyl esters, fatty alcohols, and dehydroabietic acid in order. The n-fatty acids had a main peak of C16, followed by C18. An odd or even carbon number predominance was not observed in the low-molecular-weight n-fatty acids, indicating a fossil fuel or organic matter source. However, some high-molecular-weight n-fatty acids with an even carbon predominance may derive from a biomass. The n-fatty alcohols showed a main peak of C22 and were predominated by an even carbon number, suggesting plant, microbial, or other natural origins. Phthalates, including diethyl phthalate (DEP), diisobutyl phthalate (DIBP), dibutyl phthalate (DBP), diethylhexyl phthalate (DEHP), and dimethylphthalate (DMP), were detected. The content of phthalate esters was higher in the samples collected from dense human activity areas. The concentrations of DBP, DEHP, and DIBP were relatively high, indicating an anthropogenic source. The sterols (predominantly β-sitosterol) originated from biological sources, especially plants. The n-fatty acid methyl esters and dehydroabietic acid in topsoil showed apparent even carbon predominance with the former mainly derived from microorganisms or plants and the latter from cork combustion products. PMID:27172982

  8. Applicability of the single equivalent point dipole model to represent a spatially distributed bio-electrical source

    NASA Technical Reports Server (NTRS)

    Armoundas, A. A.; Feldman, A. B.; Sherman, D. A.; Cohen, R. J.

    2001-01-01

    Although the single equivalent point dipole model has been used to represent well-localised bio-electrical sources, in realistic situations the source is distributed. Consequently, position estimates of point dipoles determined by inverse algorithms suffer from systematic error due to the non-exact applicability of the inverse model. In realistic situations, this systematic error cannot be avoided, a limitation that is independent of the complexity of the torso model used. This study quantitatively investigates the intrinsic limitations in the assignment of a location to the equivalent dipole due to distributed electrical source. To simulate arrhythmic activity in the heart, a model of a wave of depolarisation spreading from a focal source over the surface of a spherical shell is used. The activity is represented by a sequence of concentric belt sources (obtained by slicing the shell with a sequence of parallel plane pairs), with constant dipole moment per unit length (circumferentially) directed parallel to the propagation direction. The distributed source is represented by N dipoles at equal arc lengths along the belt. The sum of the dipole potentials is calculated at predefined electrode locations. The inverse problem involves finding a single equivalent point dipole that best reproduces the electrode potentials due to the distributed source. The inverse problem is implemented by minimising the chi2 per degree of freedom. It is found that the trajectory traced by the equivalent dipole is sensitive to the location of the spherical shell relative to the fixed electrodes. It is shown that this trajectory does not coincide with the sequence of geometrical centres of the consecutive belt sources. For distributed sources within a bounded spherical medium, displaced from the sphere's centre by 40% of the sphere's radius, it is found that the error in the equivalent dipole location varies from 3 to 20% for sources with size between 5 and 50% of the sphere's radius

  9. Distribution, source and chemical speciation of phosphorus in surface sediments of the central Pacific Ocean

    NASA Astrophysics Data System (ADS)

    Ni, Jianyu; Lin, Peng; Zhen, Yang; Yao, Xuying; Guo, Laodong

    2015-11-01

    The abundance of five forms of phosphorus (P) in surface sediments from the central Pacific Ocean (4.5-15ºN, 154-143ºW) was determined using a sequential extraction procedure (SEDEX) to examine the distribution and source of different P species. Total P (TP) concentrations ranged from 13.2 to 119 μmol-P/g with an average of 48.6±27.4 μmol-P/g. Within the TP pool, total inorganic P (TIP) concentrations varied from 11.1 to 121 μmol-P/g, while total organic P (TOP) concentrations ranged from undetectable to 4.8 μmol-P/g. Inorganic P was generally the predominant form in surface sediments, comprising on average up to 93% of sedimentary TP, leaving <16% as TOP. Among the five P species, the authigenic or CaCO3-bound P and detrital P were the two major P species (comprising on average 43.4±13.5% and 45.7±14.8% of TP, respectively), followed by the refractory organic P, representing 6.7±2.4% of TP. Fe-bound P accounted for 3.3±1.3% of TP, and exchangeable or adsorbed P made up less than 1% of TP. The spatial distribution of different sedimentary P species showed that higher concentrations of detrital P and Fe-bound P were both found at around 11°N, suggesting similar sources for these two P species. Much of the detrital P was derived from atmospheric sources in the study area, where heavy rainfall in the intertropical convergence zone between 3°N and 11°N has been widely reported. Compared with other marine environments, the central Pacific Ocean had relatively higher detrital P, but lower abundance of adsorbed-P and Fe-bound P. These unquine results suggested that most of the labile P could have been released into the water column during its settling from the surface to the seafloor, or that atmospheric inputs of refractory P were an important source for sedimentary P, accounting for an average of 63% of the TP, in the central Pacific Ocean. High proportions of authigenic P in deep-sea sediments, on the other hand, implied that oceanic sediments are an

  10. Distribution of attenuation in the Kaoiki, Hawaii, source volume estimated by inversion of P wave spectra

    NASA Astrophysics Data System (ADS)

    Scherbaum, Frank; Wyss, Max

    1990-08-01

    A new method to simultaneously invert for Q structure and source parameters was used on a set of 635 microearthquakes (0.9 < M < 2.0) in the Kaoiki area of southern Hawaii. Approximately 2800 signals were analyzed which had been recorded by 6 short period vertical seismographs at epicentral distances of a few to 10 km. The hypocentral depths ranged from O to 14 km, with the bulk of the sources in the 7.5-10.5 km range. The hypothesis to be tested was that the source volume of the M = 6.6 Kaoiki main shock of November 16, 1983, may be heterogeneous in attenuation distribution. We assumed that the observed P wave displacement spectra could be modelled by a source spectrum with an ω-2 high-frequency decay, a single-layer resonance filler to account for local site resonances and whole path attenuation along the ray path. In a next step the attenuation factor Q was constrained by tomographically reconstructing the three-dimensional Q structure for the source region and using it as starting model for a nonlinear inversion of the corner frequency, the seismic moment M0, and a new Q value. This process was iterated until the results changed less than 0.1% and were accepted as final. The average Q was approximately constant and very low (105source volume is strongly heterogeneous with the contrasting density of cracks controlling the difference in crustal

  11. Spatial distribution and sources of organic carbon in the surface sediment of the Bosten Lake, China

    NASA Astrophysics Data System (ADS)

    Yu, Z. T.; Wang, X. J.; Zhang, E. L.; Zhao, C. Y.; Lan, H. Y.

    2015-08-01

    Lake sediment is an important carbon reservoir. However, little is known on the dynamics and sources of sediment organic carbon in the Bosten Lake. We collected 13 surface (0-2 cm) sediment samples in the Bosten Lake and analyzed total organic carbon (TOC), total nitrogen (TN), stable carbon isotopic composition in TOC (δ13Corg) and grain size. We found a large spatial variability in TOC content (1.8-4.4 %) and δ13Corg value (-26.77 to -23.98 ‰). Using a three end member mixing model with measured TOC : TN ratio and δ13Corg, we estimated that 54-90 % of TOC was from autochthonous sources. Higher TOC content (> 3.7 %) was found in the east and central-north sections and near the mouth of the Kaidu River, which was attributable to allochthonous, autochthonous plus allochthonous, and autochthonous sources, respectively. The lowest TOC content was found in the mid-west section, which might be a result of high kinetic energy levels. Our study indicated that the spatial distribution of sediment TOC in the Bosten Lake was influenced by multiple and complex processes.

  12. Spatial distribution and sources of organic carbon in the surface sediment of Bosten Lake, China

    NASA Astrophysics Data System (ADS)

    Yu, Z. T.; Wang, X. J.; Zhang, E. L.; Zhao, C. Y.; Liu, X. Q.

    2015-11-01

    Lake sediment is an important carbon reservoir. However, little is known on the dynamics and sources of sediment organic carbon in Bosten Lake. We collected 13 surface (0-2 cm) sediment samples in Bosten Lake and analyzed total organic carbon (TOC), total nitrogen (TN), stable carbon isotopic composition in TOC (δ13Corg), and grain size. We found a large spatial variability in TOC content (1.8-4.4 %) and δ 13Corg value (-26.77 to -23.98 ‰). Using a three-end-member mixing model with measured TOC : TN ratio and δ13Corg, we estimated that 54-90 % of TOC was from autochthonous sources. Higher TOC content (> 3.7 %) was found in the east and central-north sections and near the mouth of the Kaidu River, which was attributable to allochthonous, autochthonous plus allochthonous, and autochthonous sources, respectively. The lowest TOC content was found in the mid-west section, which might be a result of high kinetic energy levels. Our study indicated that the spatial distribution of sediment TOC in the Bosten Lake was influenced by multiple and complex processes.

  13. Elemental distribution of metals in urban river sediments near an industrial effluent source.

    PubMed

    Tamim, Umma; Khan, Rahat; Jolly, Yeasmin Nahar; Fatema, Kanij; Das, Sopan; Naher, Kamrun; Islam, Mohammad Amirul; Islam, S M Azharul; Hossain, Syed Mohammod

    2016-07-01

    To study the compositional trends associated with the spatial and layer wise distribution of heavy metals as well as the sediment response towards the untreated chemical wastes, we have analyzed river (Buriganga, Bangladesh) sediments by instrumental neutron activation analysis (INAA) and energy dispersive X-ray fluorescence (EDXRF). In nine sediment samples 27 elements were determined where Na, Al, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Zn, As, Rb, Cs, La, Ce, Sm, Dy, Hf, Th and U were determined by INAA and Cu, Sr, Ba, Hg and Pb were determined by EDXRF. Pollution level and the origin of pollutants were evaluated by the aid of geo-accumulation index (Igeo), enrichment factor (EF), pollution load index (PLI) and the inter-element correlation analysis. Major elements are somehow buffered even though the pollution level is severe while the trace metals seem to be highly responsive. Among the heavy metals, Cr is the dominant pollutant, though the pollution level varies systematically with the sampling depth and the distance from the contamination source. Positive linear correlation between Cr and Zn (0.94) ensures the similar anthropogenic source(s) for these two metals, but the sediments of this study respond differently depending upon their geochemical behavior. Rare earth elements (here La, Ce, Sm and Dy), Th and U seem to have crustal origin and the Th/U ratio varies from 2.58 to 4.96. PMID:27151427

  14. Acoustic Source Localization via Distributed Sensor Networks using Tera-scale Optical-Core Devices

    SciTech Connect

    Imam, Neena; Barhen, Jacob; Wardlaw, Michael

    2008-01-01

    For real-time acoustic source localization applications, one of the primary challenges is the considerable growth in computational complexity associated with the emergence of ever larger, active or passive, distributed sensor networks. The complexity of the calculations needed to achieve accurate source localization increases dramatically with the size of sensor arrays, resulting in substantial growth of computational requirements that cannot be met with standard hardware. One option to meet this challenge builds upon the emergence of digital optical-core devices. The objective of this work was to explore the implementation of key building block algorithms used in underwater source localization on an optical-core digital processing platform recently introduced by Lenslet Inc. They investigate key concepts of threat-detection algorithms such as Time Difference Of Arrival (TDOA) estimation via sensor data correlation in the time domain with the purpose of implementation on the optical-core processor. they illustrate their results with the aid of numerical simulation and actual optical hardware runs. The major accomplishments of this research, in terms of computational speedup and numerical accurcy achieved via the deployment of optical processing technology, should be of substantial interest to the acoustic signal processing community.

  15. Distribution and Sources of Petroleum Hydrocarbons in Recent Sediments of the Imo River, SE Nigeria.

    PubMed

    Oyo-Ita, Inyang O; Oyo-Ita, Orok E; Dosunmu, Miranda I; Domínguez, Carmen; Bayona, Josep M; Albaigés, Joan

    2016-02-01

    The distribution of aliphatic and aromatic hydrocarbons in surface sediments of the lower course of the Imo River (Nigeria) was investigated to determine the sources and fate of these compounds. The aliphatic fraction is characterized by a widespread contribution of highly weathered/biodegraded hydrocarbon residues (reflected in the absence of prominent n-alkane peaks coupled with the presence of 17α(H),21β(H)-25-norhopane, an indicator of heavy hydrocarbon biodegradation) of Nigerian crude oils (confirmed by the occurrence of 18α(H)-oleanane, a compound characteristic of oils of deltaic origin). The concentrations of polycyclic aromatic hydrocarbons (PAHs) ranging from 48 to 117 ng/g dry weight (dw; ∑13PAHs) indicate a moderate pollution, possibly lowered by the sandy lithology and low organic carbon (OC) content of the sediments. Concentrations slightly decrease towards the estuary of the river, probably due to the fact that these stations are affected by tidal flushing of pollutants adsorbed on sediment particles and carried away by occasional storm to the Atlantic Ocean. A number of PAH ratios, including parent/alkylated and isomeric compounds, indicates a predominance of petrogenic sources, with a low contribution of pyrolytic inputs, particularly of fossil fuel combustion. On the basis of OC/ON (>10) and Per/ΣPAHpenta- (>10) values, a diagenetic terrigenous OC was proposed as a source of perylene to the river. PMID:26546420

  16. Planck Early Results. XV. Spectral Energy Distributions and Radio Continuum Spectra of Northern Extragalactic Radio Sources

    NASA Technical Reports Server (NTRS)

    Aatrokoski, J.; Ade, P. A. R.; Aghanim, N.; Aller, H. D.; Aller, M. F.; Angelakis, E.; Amaud, M.; Ashdown, M.; Aumont, J.; Baccigalupi, C.; Balbi, A.; Banday, A. J.; Barreiro, R. B.; Bartlett, J. G.; Battaner, E.; Benabed, K.; Benoit, A.; Berdyugin, A.; Bernard, J. P.; Bersanelli, M.; Bhatia, R.; Bonaldi, A.; Bonavera, L.; Gehrels, N.

    2011-01-01

    Spectral energy distributions (SEDs) and radio continuum spectra are presented for a northern sample of 104 extragalactic radio sources. based on the Planck Early Release Compact Source Catalogue (ERCSC) and simultaneous multi frequency data. The nine Planck frequencies, from 30 to 857 GHz, are complemented by a set of simultaneous observations ranging from radio to gamma-rays. This is the first extensive frequency coverage in the radio and millimetre domains for an essentially complete sample of extragalactic radio sources, and it shows how the individual shocks, each in their own phase of development, shape the radio spectra as they move in the relativistic jet. The SEDs presented in this paper were fitted with second and third degree polynomials to estimate the frequencies of the synchrotron and inverse Compton (IC) peaks, and the spectral indices of low and high frequency radio data, including the Planck ERCSC data, were calculated. SED modelling methods are discussed, with an emphasis on proper. physical modelling of the synchrotron bump using multiple components. Planck ERCSC data also suggest that the original accelerated electron energy spectrum could be much harder than commonly thought, with power-law index around 1.5 instead of the canonical 2.5. The implications of this are discussed for the acceleration mechanisms effective in blazar shock. Furthermore in many cases the Planck data indicate that gamma-ray emission must originate in the same shocks that produce the radio emission.

  17. Distribution of 1,4-dioxane in relation to possible sources in the water environment.

    PubMed

    Abe, A

    1999-02-16

    The distribution of 1,4-dioxane was investigated in surface and groundwater in relation to possible sources. Water samples from river, coastal sea, and groundwater were collected and examined in Kanagawa Prefecture, Japan, from 1995 to 1998. Almost all samples were contaminated by 1,4-dioxane. On annual changes, the concentrations did not vary significantly in river water. However, some samples were still heavily polluted in groundwater. The highest correlation was between the concentration of 1,4-dioxane and 1,1,1-trichloroethane in the polluted groundwater samples. Soil and groundwater that was polluted by 1,1,1-trichloroethane in the past is still a possible source of 1,4-dioxane. In regard to a survey of other sources, effluents from the combined collection treatment from apartment houses, river basin sewage systems, and chemical plants were examined. The load unit of 1,4-dioxane from the treated effluent of domestic wastewater was assumed to be approximately 0.25 mg/person/day. This was derived from commonly used household chemicals, which contained 1,4-dioxane as a by-product. In river basin sewage systems, the concentrations in effluents varied significantly. High concentration inflows were probably not degraded and released. Although 50-60% of removal was recognized in acclimatized activated sludge from a chemical plant, 1,4-dioxane was easily desorbed with water from sludge. PMID:10209880

  18. Spatial distribution and source identification of trace elements in topsoil from heavily industrialized region, Aliaga, Turkey.

    PubMed

    Kara, Melik; Dumanoğlu, Yetkin; Altıok, Hasan; Elbir, Tolga; Odabası, Mustafa; Bayram, Abdurrahman

    2014-10-01

    Topsoil samples (n = 40) were collected from a heavily industrialized region in Turkey. The region includes several scrap processing iron-steel plants with electric arc furnaces (EAFs), a petroleum refinery, a petrochemical complex, steel rolling mills, a natural gas-fired power plant, ship-breaking yards and very dense transportation activities. The region has undergone a rapid transition from an agricultural region to a heavily industrialized region in the last three decades. Collected soil samples were analyzed for 48 trace elements using inductively coupled plasma-mass spectrometry (ICP-MS). The elemental distribution pattern in the region indicated that Nemrut area with dense iron-steel production activities was a hotspot for elemental pollution. In addition to crustal elements, concentrations of anthropogenic trace elements (i.e., Fe, Zn, Pb, Mn, Cu, Cd, Cr and Mo) were very high in the area influencing many parts of the region. Elemental compositions of fugitive sources polluting the soil (i.e., paved and unpaved roads, slag piles, EAFs filter dust piles and coal piles) were also determined. The methods (enrichment factors [EFs] and the index of geoaccumulation [Igeo]) used for determination of pollution status of soil showed that Cr, Ag, Zn, As and Pb were the strongly contaminating elements for the region. Principal component analysis (PCA) clearly indicated that anthropogenic sources (steel production, refinery and petrochemical processes and traffic) were important sources in this region. PMID:24859861

  19. Comparison between Two Practical Methods of Light Source Monitoring in Quantum Key Distribution

    NASA Astrophysics Data System (ADS)

    Wang, Gan; Chen, Ziyang; Xu, Bingjie; Li, Zhengyu; Peng, Xiang; Guo, Hong

    2016-05-01

    The practical security of a quantum key distribution (QKD) is a critical issue due to the loopholes opened by the imperfections of practical devices. The untrusted source problem is a fundamental issue that exists in almost every protocol, including the loss-tolerant protocol and the measurement-device-independent protocol. Two practical light source monitoring methods were proposed, i.e., two-threshold detector scheme and photon-number-resolving (PNR) detector scheme. In this work, we test the fluctuation level of different gain-switched pulsed lasers, i.e., the ratio between the standard deviation and the mean of the pulse energy (noted as γ) changes from 1% to 7%. Moreover, we propose an improved practical PNR detector scheme, and discuss in what circumstances one should use which light source monitoring method, i.e., generally speaking when the fluctuation is large the PNR detector method performs better. This provides an instruction of selecting proper monitoring module for different practical systems. This work is supported by the National Science Fund for Distinguished Young Scholars of China (Grant No. 61225003), the State Key Project of National Natural Science Foundation of China (Grant No. 61531003).

  20. On the Vertical Distribution of Local and Remote Sources of Water for Precipitation

    NASA Technical Reports Server (NTRS)

    Bosilovich, Michael G.

    2001-01-01

    The vertical distribution of local and remote sources of water for precipitation and total column water over the United States are evaluated in a general circulation model simulation. The Goddard Earth Observing System (GEOS) general circulation model (GCM) includes passive constituent tracers to determine the geographical sources of the water in the column. Results show that the local percentage of precipitable water and local percentage of precipitation can be very different. The transport of water vapor from remote oceanic sources at mid and upper levels is important to the total water in the column over the central United States, while the access of locally evaporated water in convective precipitation processes is important to the local precipitation ratio. This result resembles the conceptual formulation of the convective parameterization. However, the formulations of simple models of precipitation recycling include the assumption that the ratio of the local water in the column is equal to the ratio of the local precipitation. The present results demonstrate the uncertainty in that assumption, as locally evaporated water is more concentrated near the surface.

  1. Distribution and sources of organic matter in surface sediments of the eastern continental margin of India

    NASA Astrophysics Data System (ADS)

    Krishna, M. S.; Naidu, S. A.; Subbaiah, Ch. V.; Sarma, V. V. S. S.; Reddy, N. P. C.

    2013-12-01

    sources and distribution of organic matter (OM) in surface sediments of the eastern continental margin of India, including the region influenced by river discharge, were investigated using content, molar C:N ratios and stable isotopes of carbon and nitrogen. Despite relatively high water column integrated chlorophyll-a concentrations were found in the continental shelf than the slope; however, the lower sediment organic carbon (SOC) was found in the former than the latter region suggesting that in situ production did not play significant role on preservation of SOC in the coastal Bay of Bengal. The broad range of δ13C of SOC (-23.2 to -16.7‰) suggests that OM is a broad mixture of terrestrial and marine OM. Relative contributions from terrestrial C3 and C4 plants and marine sources are quantified as 34%, 23%, and 43%, respectively, indicating that dominant source of allochthonous OM (~57%) in the coastal Bay of Bengal. Relatively higher contribution of OM from C4 plants was found in the sediments at off river Krishna indicating that this region received detritus of agricultural crops such as jowar, bajra, and sugar cane, which are dominant in its drainage basin, during SW monsoon. This study revealed that relatively high OM preserved in the slope than shelf region along the coastal Bay of Bengal and the composition of OM is primarily controlled by the type of agricultural crops and vegetation in the drainage basin of the river.

  2. Central graben (Norway) - Hydrocarbon distribution related to source rock maturation and pressure regimes

    SciTech Connect

    Chiarelli, A.; Issard, F. )

    1990-05-01

    This study of the Central graben was limited to the north by 57{degree}25'N, to the west by 4{degree}30', and to the east and south by the borders of the United Kingdom and Denmark, respectively. Several fields have been discovered within the Upper Cretaceous, Paleocene, and Jurassic strata for which the source rocks are Jurassic age. The amount and types of hydrocarbons generated from the source rocks have been estimated by accounting for their thickness, their initial potential, and their degree of maturation. The possibilities for hydrocarbon migration have been interpreted through an integration of the structural history and the hydrodynamic framework within the Central graben region. The hydrodynamic framework which appears to be a very important parameter in the study area, has been reconstructed from pressure measurements in the reservoirs, compaction profiles, and numerical modeling. It appears that vertical migration from the Jurassic source rocks toward the Upper Cretaceous and Paleocene reservoirs was mainly dependent on tectonics, salt diapirism and geopressuring. In the Central graben region the understanding of areal distribution and nature of hydrocarbons formed has been greatly improved by the integration of geochemistry and hydrodynamics. This conclusion could be extended to many other sedimentary basins in the world.

  3. Source attack of decoy-state quantum key distribution using phase information

    NASA Astrophysics Data System (ADS)

    Tang, Yan-Lin; Yin, Hua-Lei; Ma, Xiongfeng; Fung, Chi-Hang Fred; Liu, Yang; Yong, Hai-Lin; Chen, Teng-Yun; Peng, Cheng-Zhi; Chen, Zeng-Bing; Pan, Jian-Wei

    2013-08-01

    Quantum key distribution (QKD) utilizes the laws of quantum mechanics to achieve information-theoretically secure key generation. This field is now approaching the stage of commercialization, but many practical QKD systems still suffer from security loopholes due to imperfect devices. In fact, practical attacks have successfully been demonstrated. Fortunately, most of them only exploit detection-side loopholes, which are now closed by the recent idea of measurement-device-independent QKD. On the other hand, little attention is paid to the source, which may still leave QKD systems insecure. In this work, we propose and demonstrate an attack that exploits a source-side loophole existing in qubit-based QKD systems using a weak coherent state source and decoy states. Specifically, by implementing a linear-optics unambiguous state discrimination measurement, we show that the security of a system without phase randomization—which is a step assumed in conventional security analyses but sometimes neglected in practice—can be compromised. We conclude that implementing phase randomization is essential to the security of decoy-state QKD systems under current security analyses.

  4. Passive decoy-state quantum key distribution with practical light sources

    SciTech Connect

    Curty, Marcos; Ma, Xiongfeng; Qi, Bing; Moroder, Tobias

    2010-02-15

    Decoy states have been proven to be a very useful method for significantly enhancing the performance of quantum key distribution systems with practical light sources. Although active modulation of the intensity of the laser pulses is an effective way of preparing decoy states in principle, in practice passive preparation might be desirable in some scenarios. Typical passive schemes involve parametric down-conversion. More recently, it has been shown that phase-randomized weak coherent pulses (WCP) can also be used for the same purpose [M. Curty et al., Opt. Lett. 34, 3238 (2009).] This proposal requires only linear optics together with a simple threshold photon detector, which shows the practical feasibility of the method. Most importantly, the resulting secret key rate is comparable to the one delivered by an active decoy-state setup with an infinite number of decoy settings. In this article we extend these results, now showing specifically the analysis for other practical scenarios with different light sources and photodetectors. In particular, we consider sources emitting thermal states, phase-randomized WCP, and strong coherent light in combination with several types of photodetectors, like, for instance, threshold photon detectors, photon number resolving detectors, and classical photodetectors. Our analysis includes as well the effect that detection inefficiencies and noise in the form of dark counts shown by current threshold detectors might have on the final secret key rate. Moreover, we provide estimations on the effects that statistical fluctuations due to a finite data size can have in practical implementations.

  5. Kr II and Xe II axial velocity distribution functions in a cross-field ion source

    SciTech Connect

    Lejeune, A.; Bourgeois, G.; Mazouffre, S.

    2012-07-15

    Laser induced fluorescence measurements were carried out in a cross-field ion source to examine the behaviour of the axial ion velocity distribution functions (VDFs) in the expanding plasma. In the present paper, we focus on the axial VDFs of Kr II and Xe II ions. We examine the contourplots in a 1D-phase space (x,v{sub x}) representation in front of the exhaust channel and along the centerline of the ion source. The main ion beam, whose momentum corresponds to the ions that are accelerated through the whole potential drop, is observed. A secondary structure reveals the ions coming from the opposite side of the channel. We show that the formation of the neutralized ion flow is governed by the annular geometry. The assumption of a collisionless shock or a double layer due to supersonic beam interaction is not necessary. A non-negligible fraction of slow ions originates in local ionization or charge-exchange collision events between ions of the expanding plasma and atoms of the background residual gas. Slow ions that are produced near the centerline in the vicinity of the exit plane are accelerated toward the source body with a negative velocity leading to a high sputtering of front face. On the contrary, the ions that are produced in the vicinity of the channel exit plane are partially accelerated by the extended electric field.

  6. Kr II and Xe II axial velocity distribution functions in a cross-field ion source

    NASA Astrophysics Data System (ADS)

    Lejeune, A.; Bourgeois, G.; Mazouffre, S.

    2012-07-01

    Laser induced fluorescence measurements were carried out in a cross-field ion source to examine the behaviour of the axial ion velocity distribution functions (VDFs) in the expanding plasma. In the present paper, we focus on the axial VDFs of Kr II and Xe II ions. We examine the contourplots in a 1D-phase space (x,vx) representation in front of the exhaust channel and along the centerline of the ion source. The main ion beam, whose momentum corresponds to the ions that are accelerated through the whole potential drop, is observed. A secondary structure reveals the ions coming from the opposite side of the channel. We show that the formation of the neutralized ion flow is governed by the annular geometry. The assumption of a collisionless shock or a double layer due to supersonic beam interaction is not necessary. A non-negligible fraction of slow ions originates in local ionization or charge-exchange collision events between ions of the expanding plasma and atoms of the background residual gas. Slow ions that are produced near the centerline in the vicinity of the exit plane are accelerated toward the source body with a negative velocity leading to a high sputtering of front face. On the contrary, the ions that are produced in the vicinity of the channel exit plane are partially accelerated by the extended electric field.

  7. Optimal operation management of fuel cell/wind/photovoltaic power sources connected to distribution networks

    NASA Astrophysics Data System (ADS)

    Niknam, Taher; Kavousifard, Abdollah; Tabatabaei, Sajad; Aghaei, Jamshid

    2011-10-01

    In this paper a new multiobjective modified honey bee mating optimization (MHBMO) algorithm is presented to investigate the distribution feeder reconfiguration (DFR) problem considering renewable energy sources (RESs) (photovoltaics, fuel cell and wind energy) connected to the distribution network. The objective functions of the problem to be minimized are the electrical active power losses, the voltage deviations, the total electrical energy costs and the total emissions of RESs and substations. During the optimization process, the proposed algorithm finds a set of non-dominated (Pareto) optimal solutions which are stored in an external memory called repository. Since the objective functions investigated are not the same, a fuzzy clustering algorithm is utilized to handle the size of the repository in the specified limits. Moreover, a fuzzy-based decision maker is adopted to select the 'best' compromised solution among the non-dominated optimal solutions of multiobjective optimization problem. In order to see the feasibility and effectiveness of the proposed algorithm, two standard distribution test systems are used as case studies.

  8. Optimal operation management of fuel cell/wind/photovoltaic power sources connected to distribution networks

    NASA Astrophysics Data System (ADS)

    Niknam, Taher; Kavousifard, Abdollah; Tabatabaei, Sajad; Aghaei, Jamshid

    2011-10-01

    In this paper a new multiobjective modified honey bee mating optimization (MHBMO) algorithm is presented to investigate the distribution feeder reconfiguration (DFR) problem considering renewable energy sources (RESs) (photovoltaics, fuel cell and wind energy) connected to the distribution network. The objective functions of the problem to be minimized are the electrical active power losses, the voltage deviations, the total electrical energy costs and the total emissions of RESs and substations. During the optimization process, the proposed algorithm finds a set of non-dominated (Pareto) optimal solutions which are stored in an external memory called repository. Since the objective functions investigated are not the same, a fuzzy clustering algorithm is utilized to handle the size of the repository in the specified limits. Moreover, a fuzzy-based decision maker is adopted to select the ‘best' compromised solution among the non-dominated optimal solutions of multiobjective optimization problem. In order to see the feasibility and effectiveness of the proposed algorithm, two standard distribution test systems are used as case studies.

  9. Inverting seismic noise cross-correlations for noise source distribution: A step towards reducing source-induced bias in seismic noise interferometry

    NASA Astrophysics Data System (ADS)

    Ermert, Laura; Afanasiev, Michael; Sager, Korbinian; Gokhberg, Alexey; Fichtner, Andreas

    2016-04-01

    We report on the ongoing development of a new inversion method for the space- and time-dependent power spectral density distribution of ambient seismic noise sources. The method, once complete, will mainly serve two purposes: First, it will allow us to construct more realistic forward models for noise cross-correlation waveforms, thereby opening new possibilities for waveform imaging by ambient noise tomography. Second, it may provide new insights about the properties of ambient noise sources, complementing studies based on beamforming or numerical modeling of noise based on oceanographic observations. To invert for noise sources, we consider surface wave signal energy measurements on the 'causal' (station A to B) and on the 'acausal' (station B to A) correlation branch, and the ratio between them. These and similar measurements have proven useful for locating noise sources using cross-correlations in several past studies. The inversion procedure is the following: We construct correlation forward models based on Green's functions from a spectral element wave propagation code. To construct these models efficiently, we use source-receiver reciprocity and assume spatial uncorrelation of noise sources. In such a setting, correlations can be calculated from a pre-computed set of Green's functions between the seismic receivers and sources located at the Earth's surface. We then calculate spatial sensitivity kernels for the noise source distribution with respect to the correlation signal energy measurements. These in turn allow us to construct a misfit gradient and optimize the source distribution model to fit our observed cross-correlation signal energies or energy ratios. We will present the workflow for calculation of the forward model and sensitivity kernels, as well as results for both forward modeling and kernels for an example data set of long-period noise or 'hum' at a global scale. We will also provide an outlook on the noise source inversion considering the

  10. ACS Quicklook PDF products

    NASA Astrophysics Data System (ADS)

    Suchkov, Anatoly

    1999-12-01

    This report details the features of the ACS quicklook PDF products produced by the HST data pipeline. The requirements closely follow the design of paper products recommended by the Data Quality Committee, with appropriate changes required to fully support ACS.

  11. [Distribution Characteristics and Source Analysis of Dustfall Trace Elements During Winter in Beijing].

    PubMed

    Xiong, Qiu-lin; Zhao, Wen-ji; Guo, Xiao-yu; Chen, Fan-tao; Shu, Tong-tong; Zheng, Xiao-xia; Zhao, Wen-hui

    2015-08-01

    The dustfall content is one of the evaluation indexes of atmospheric pollution. Trace elements especially heavy metals in dustfall can lead to risks to ecological environment and human health. In order to study the distribution characteristics of trace elements, heavy metals pollution and their sources in winter atmospheric dust, 49 dustfall samples were collected in Beijing City and nearby during November 2013 to March 2014. Then the contents (mass percentages) of 40 trace elements were measured by Elan DRC It type inductively coupled plasma mass (ICP-MS). Test results showed that more than half of the trace elements in the dust were less than 10 mg x kg(-1); about a quarter were between 10-100 mg x kg-1); while 7 elements (Pb, Zr, Cr, Cu, Zn, Sr and Ba) were more than 100 mg x kg(-1). The contents of Pb, Cu, Zn, Bi, Cd and Mo of winter dustfall in Beijing city.were respectively 4.18, 4.66, 5.35, 6.31, 6.62, and 8.62 times as high as those of corresponding elements in the surface soil in the same period, which went beyond the soil background values by more than 300% . The contribution of human activities to dustfall trace heavy metals content in Beijing city was larger than that in the surrounding region. Then sources analysis of dustfall and its 20 main trace elements (Cd, Mo, Nb, Ga, Co, Y, Nd, Li, La, Ni, Rb, V, Ce, Pb, Zr, Cr, Cu, Zn, Sr, Ba) was conducted through a multi-method analysis, including Pearson correlation analysis, Kendall correlation coefficient analysis and principal component analysis. Research results indicated that sources of winter dustfall in Beijing city were mainly composed of the earth's crust sources (including road dust, construction dust and remote transmission of dust) and the burning of fossil fuels (vehicle emissions, coal combustion, biomass combustion and industrial processes). PMID:26591998

  12. Large-Scale Transport Model Uncertainty and Sensitivity Analysis: Distributed Sources in Complex Hydrogeologic Systems

    SciTech Connect

    Sig Drellack, Lance Prothro

    2007-12-01

    The Underground Test Area (UGTA) Project of the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office is in the process of assessing and developing regulatory decision options based on modeling predictions of contaminant transport from underground testing of nuclear weapons at the Nevada Test Site (NTS). The UGTA Project is attempting to develop an effective modeling strategy that addresses and quantifies multiple components of uncertainty including natural variability, parameter uncertainty, conceptual/model uncertainty, and decision uncertainty in translating model results into regulatory requirements. The modeling task presents multiple unique challenges to the hydrological sciences as a result of the complex fractured and faulted hydrostratigraphy, the distributed locations of sources, the suite of reactive and non-reactive radionuclides, and uncertainty in conceptual models. Characterization of the hydrogeologic system is difficult and expensive because of deep groundwater in the arid desert setting and the large spatial setting of the NTS. Therefore, conceptual model uncertainty is partially addressed through the development of multiple alternative conceptual models of the hydrostratigraphic framework and multiple alternative models of recharge and discharge. Uncertainty in boundary conditions is assessed through development of alternative groundwater fluxes through multiple simulations using the regional groundwater flow model. Calibration of alternative models to heads and measured or inferred fluxes has not proven to provide clear measures of model quality. Therefore, model screening by comparison to independently-derived natural geochemical mixing targets through cluster analysis has also been invoked to evaluate differences between alternative conceptual models. Advancing multiple alternative flow models, sensitivity of transport predictions to parameter uncertainty is assessed through Monte Carlo simulations. The

  13. Distribution, sources and budgets of particulate phosphorus and nitrogen in the East China Sea

    NASA Astrophysics Data System (ADS)

    Yu, Yu; Song, Jinming; Li, Xuegang; Yuan, Huamao; Li, Ning

    2012-07-01

    Suspended particles were collected from the northern East China Sea (ECS) in four spring and autumn cruises to study the sources and biogeochemical behavior of particulate inorganic and organic phosphorus and nitrogen (PIP, POP, PIN, and PON). PIP and PON were dominant forms of particulate P and N, accounting for 57.2% of TPP and 78.2% of TPN, respectively. PIP and POP concentrations decreased seaward from the estuary, and had high values near Zhoushan Islands and in the northern ECS. It was indicated that the Changjiang dilute water (CDW) and the Jiangsu coastal currents (JCC), which were rich in particulate phosphorus were the major sources of PIP and POP. PIN and PON concentrations exhibited decreasing trend from the middle shelf toward land and offshore, suggesting the dilution effect of N-depleted riverine particles on particulate nitrogen in coastal waters. The highest concentrations of PIN and PON were observed in the coast of Zhejiang and in the northern ECS, which were two productive areas in the ECS. PON and PIN were primarily of marine source and POP was also influenced by phytoplankton productivity. The concentrations, compositions and distribution of particulate nutrients varied between spring and autumn, in response to the seasonal variations of phytoplankton productivity and terrestrial input. Budget calculation demonstrated that the sediment flux of Changjiang accounted for 88% of total input flux in spring and summer, indicating that the Changjiang River was the major particle source in the ECS. Particulate P was mainly from phytoplankton and the input of the Changjiang River, while the major source of particulate N was phytoplankton. Phytoplankton production contributed 70% of TPP input flux and 95% of TPN input flux in spring and summer, while 64% of TPP input and 89% of TPN input in autumn and winter. It was shown that riverine particles were enriched in inorganic P, whereas marine particles had high organic P and N content, which suggested that

  14. Scheme for realizing passive quantum key distribution with heralded single-photon sources

    NASA Astrophysics Data System (ADS)

    Wang, Qin; Zhang, Chun-Hui; Wang, Xiang-Bin

    2016-03-01

    We present a scheme for realizing passive quantum key distribution with heralded single-photon sources. In this scheme, the idler light from the parametric down-conversion process is split into two parts and sent into two local detectors individually. Then all the clicking and nonclicking events are used to herald the arrival and nonarrival of the signal light. As a result, a precise estimation of the behavior of the single-photon pulses can be achieved without changing the light intensity. Furthermore, we compare our scheme with other existing methods with the Bennett-Brassard 1984 (BB84) protocol through numerical simulations. Our simulations demonstrate that the performance of our scheme can greatly overcome other existing practical methods and approach very close to the asymptotic case of using infinite-decoy-state methods.

  15. Development of a high-energy distributed energy source electromagnetic railgun with improved energy conversion efficiency

    SciTech Connect

    Tower, M.M.; Haight, C.H.

    1984-03-01

    Vought Corporation in cooperation with the Center for Electromechanics at the University of Texas (CEM-UT) has developed under sponsorship by the Defense Advanced Research Projects Agency (DARPA) and the Army Armament, Munitions, and Chemical Command (AMCCOM) a high-energy distributed energy source (DES) electromagnetic (EM) railgun accelerator. This paper discusses the development and current status of the DES railgun which has the design capability to launch projectile masses up to 60 grams to the 3-4 km/sec velocity regime with energy conversion efficiencies above 35 percent. These goals are being accomplished through utilization of scaled-energy CEM-UT railgun experiments for sequenced timing/staging and a full energy (575 kJ) design at Vought for high efficiency capability. The operational Vought single-pulse railgun forms the baseline for the full energy testing.

  16. Size distribution, mixing state and source apportionments of black carbon aerosols in London during winter time

    NASA Astrophysics Data System (ADS)

    Liu, D.; Allan, J. D.; Young, D. E.; Coe, H.; Beddows, D.; Fleming, Z. L.; Flynn, M. J.; Gallagher, M. W.; Harrison, R. M.; Lee, J.; Prevot, A. S. H.; Taylor, J. W.; Yin, J.; Williams, P. I.; Zotter, P.

    2014-06-01

    Black carbon aerosols (BC) at a London urban site were characterized in both winter and summer time 2012 during the Clean Air for London (ClearfLo) project. Positive matrix factorization (PMF) factors of organic aerosol mass spectra measured by a high resolution aerosol mass spectrometer (HR-AMS) showed traffic-dominant sources in summer but in winter the influence of additional non-traffic sources became more important, mainly from solid fuel sources (SF). Measurements using a single particle soot photometer (SP2, DMT), showed the traffic-dominant BC exhibited an almost uniform BC core size (Dc) distribution with very thin coating thickness throughout the detectable range of Dc. However the size distribution of Dc (project average mass median Dc = 149 ± 22 nm in winter, and 120 ± 6 nm in summer) and BC coating thickness varied significantly in winter. A novel methodology was developed to attribute the BC number concentrations and mass abundances from traffic (BCtr) and from SF (BCsf), by using a 2-D histogram of the particle optical properties as a function of BC core size, as measured by the SP2. The BCtr and BCsf showed distinctly different Dc distributions and coating thicknesses, with BCsf displaying larger Dc and larger coating thickness compared to BCtr. BC particles from different sources were also apportioned by applying a multiple linear regression between the total BC mass and each AMS-PMF factor (BC-AMS-PMF method), and also attributed by applying the absorption spectral dependence of carbonaceous aerosols to 7-wavelength Aethalometer measurements (Aethalometer method). Air masses that originated from westerly (W), southeasterly (SE), or easterly (E) sectors showed BCsf fractions that ranged from low to high, and whose mass median Dc values were 137 ± 10 nm, 143 ± 11 nm, and 169 ± 29 nm respectively. The corresponding bulk relative coating thickness of BC (coated particle size / BC core - Dp / Dc) for these same sectors was 1.28 ± 0.07, 1.45 ± 0

  17. Size distribution, mixing state and source apportionment of black carbon aerosol in London during wintertime

    NASA Astrophysics Data System (ADS)

    Liu, D.; Allan, J. D.; Young, D. E.; Coe, H.; Beddows, D.; Fleming, Z. L.; Flynn, M. J.; Gallagher, M. W.; Harrison, R. M.; Lee, J.; Prevot, A. S. H.; Taylor, J. W.; Yin, J.; Williams, P. I.; Zotter, P.

    2014-09-01

    Black carbon aerosols (BC) at a London urban site were characterised in both winter- and summertime 2012 during the Clean Air for London (ClearfLo) project. Positive matrix factorisation (PMF) factors of organic aerosol mass spectra measured by a high-resolution aerosol mass spectrometer (HR-AMS) showed traffic-dominant sources in summer but in winter the influence of additional non-traffic sources became more important, mainly from solid fuel sources (SF). Measurements using a single particle soot photometer (SP2, DMT), showed the traffic-dominant BC exhibited an almost uniform BC core size (Dc) distribution with very thin coating thickness throughout the detectable range of Dc. However, the size distribution of sf (project average mass median Dc = 149 ± 22 nm in winter, and 120 ± 6 nm in summer) and BC coating thickness varied significantly in winter. A novel methodology was developed to attribute the BC number concentrations and mass abundances from traffic (BCtr) and from SF (BCsf), by using a 2-D histogram of the particle optical properties as a function of BC core size, as measured by the SP2. The BCtr and BCsf showed distinctly different sf distributions and coating thicknesses, with BCsf displaying larger Dc and larger coating thickness compared to BCtr. BC particles from different sources were also apportioned by applying a multiple linear regression between the total BC mass and each AMS-PMF factor (BC-AMS-PMF method), and also attributed by applying the absorption spectral dependence of carbonaceous aerosols to 7-wavelength Aethalometer measurements (Aethalometer method). Air masses that originated from westerly (W), southeasterly (SE), and easterly (E) sectors showed BCsf fractions that ranged from low to high, and whose mass median Dc values were 137 ± 10 nm, 143 ± 11 nm and 169 ± 29 nm, respectively. The corresponding bulk relative coating thickness of BC (coated particle size/BC core - Dp/Dc) for these same sectors was 1.28 ± 0.07, 1.45 ± 0

  18. [Distribution Characteristics and Source Identification of Organochlorine Pesticides in Surface Soil in Karst Underground River Basin].

    PubMed

    Xie, Zheng-lan; Sun, Yu-chuan; Zhang, Mei; Yu, Qin; Xu, Xin

    2016-03-15

    Six typical surface soil samples were taken in Laolongdong underground river basin, and 20 OCPs were analyzed by gas chromatography equipped with micro-⁶³Ni electron capture detector. The purpose of this study was to investigate the distribution, composition and source of organochlorine pesticides ( OCPs) in the surface soil of Laolongdong underground river basin, and to further evaluate the pollution level. The results showed that 20 OCPs were inordinately detected in the soil samples and the detection rate of 16 OCPs (except for p,p'-DDE, cis-Chlordane, trans-Chlordane, dieldrin) was 100%. Moreover, the CHLs and DDTs were the main contaminants, and there were obvious differences in the concentrations of organochlorine pesticides between different sampling points. The concentration range of total OCPs was 5.57-2,618.57 ng · g⁻¹ with a mean of 467.28 ng · g⁻¹. Compared with other regions both at home and abroad, the concentrations of HCHs and DDTs in the surface soil samples of the studied area were arranged from high to middle levels. The total concentrations of OCPs, HCHs, DDTs and CHLs had a similar variation tendency in spatial distribution, upstream > midstream > downstream, and the concentrations of OCPs in upstream were obviously higher than those in midstream and downstream. Source analysis indicated that the HCHs mainly came from the use of lindane. DDTs in soil came from not only the early residues but also recently illegal use of industrial DDTs and the input of dicofol. In addition, chlordan was mainly from the early residues and atmospheric deposition. Compared with the Environmental Quality Standard for Soils of China and Netherlands, the level of OCPs in Xinli vilage soil was categorized as highly polluted, but the levels of OCPs in Longjing bay, Xia spit, and Zhao courtyard soils were classified as slightly polluted, while the Longjing adjacency and gaozhong temple soils belonged to unpolluted ones. PMID:27337880

  19. Electromagnetic Modeling of Distributed-Source-Excitation of Coplanar Waveguides: Applications to Traveling-Wave Photomixers

    NASA Technical Reports Server (NTRS)

    Pasqualini, Davide; Neto, Andrea; Wyss, Rolf A.

    2001-01-01

    In this work an electromagnetic model and subsequent design is presented for a traveling-wave, coplanar waveguide (CPW) based source that will operate in the THz frequency regime. The radio frequency (RF) driving current is a result of photoexcitation of a thin GaAs membrane using two frequency-offset lasers. The GaAs film is grown by molecular-beam-epitaxy (MBE) and displays sub-ps carrier lifetimes which enable the material conductivity to be modulated at a very high rate. The RF current flows between electrodes deposited on the GaAs membrane which are biased with a DC voltage source. The electrodes form a CPW and are terminated with a double slot antenna that couples the power to a quasi-optical system. The membrane is suspended above a metallic reflector to launch all radiation in one direction. The theoretical investigation and consequent design is performed in two steps. The first step consists of a direct evaluation of the magnetic current distribution on an infinitely extended coplanar waveguide excited by an impressed electric current distributed over a finite area. The result of the analysis is the difference between the incident angle of the laser beams and the length of the excited area that maximizes the RF power coupled to the CPW. The optimal values for both parameters are found as functions of the CPW and membrane dimensions as well as the dielectric constants of the layers. In the second step, a design is presented of a double slot antenna that matches the CPW characteristic impedance and gives good overall performance. The design is presently being implemented and measurements will soon be available.

  20. Far-field DOA estimation and source localization for different scenarios in a distributed sensor network

    NASA Astrophysics Data System (ADS)

    Asgari, Shadnaz

    Recent developments in the integrated circuits and wireless communications not only open up many possibilities but also introduce challenging issues for the collaborative processing of signals for source localization and beamforming in an energy-constrained distributed sensor network. In signal processing, various sensor array processing algorithms and concepts have been adopted, but must be further tailored to match the communication and computational constraints. Sometimes the constraints are such that none of the existing algorithms would be an efficient option for the defined problem and as the result; the necessity of developing a new algorithm becomes undeniable. In this dissertation, we present the theoretical and the practical issues of Direction-Of-Arrival (DOA) estimation and source localization using the Approximate-Maximum-Likelihood (AML) algorithm for different scenarios. We first investigate a robust algorithm design for coherent source DOA estimation in a limited reverberant environment. Then, we provide a least-square (LS) solution for source localization based on our newly proposed virtual array model. In another scenario, we consider the determination of the location of a disturbance source which emits both wideband acoustic and seismic signals. We devise an enhanced AML algorithm to process the data collected at the acoustic sensors. For processing the seismic signals, two distinct algorithms are investigated to determine the DOAs. Then, we consider a basic algorithm for fusion of the results yielded by the acoustic and seismic arrays. We also investigate the theoretical and practical issues of DOA estimation in a three-dimensional (3D) scenario. We show that the performance of the proposed 3D AML algorithm converges to the Cramer-Rao Bound. We use the concept of an isotropic array to reduce the complexity of the proposed algorithm by advocating a decoupled 3D version. We also explore a modified version of the decoupled 3D AML algorithm which

  1. Use of atmospheric elemental size distributions in estimating aerosol sources in the Helsinki area

    NASA Astrophysics Data System (ADS)

    Pakkanen, Tuomo A.; Kerminen, Veli-Matti; Korhonen, Christina H.; Hillamo, Risto E.; Aarnio, Päivi; Koskentalo, Tarja; Maenhaut, Willy

    In June 1996-June 1997 Berner impactors were used in the Helsinki area to measure size distributions of atmospheric aerosols simultaneously at an urban and at a rural site. Ten sample pairs were collected in the size range of 0.03-15.7 μm of equivalent aerodynamic diameter (EAD). Average size distributions at the two sites were calculated for 29 elements, particulate mass, and sulphate. At both sites especially sulphate, As, B, Bi, Cd, Ni, Tl, and V were enriched in fine particles (EAD<2.3 μm). In order to estimate local fine-particle sources of the various chemical components, the similarities and dissimilarities in the accumulation-mode parameters were studied separately for both sites. It was observed that often in different samples, different components had similar accumulation modes. At both sites, particulate mass, As, and Pb had similar accumulation modes to sulphate which suggests that long-range transport (LRT) is important for these components. V, Ni, Mo, and Co formed another group of similar accumulation modes at both sites suggesting that these elements largely originated from local and regional oil combustion. In addition, other groups of similar accumulation modes were observed but these groups were different between the sites. The meteorological parameters indicated that seven sample pairs formed a subset of the data in which the local emissions of the Helsinki area were transported to the urban site but not to the rural site. For this subset the rural fine-particle concentrations were considered to represent an upper limit estimate for the LRT. These upper limit LRT estimations were further improved by utilising the quantitative relative size distributions (QRSD) method at the rural site. The QRSD method supposes that in the fine-particle size range the LRT fractions of all chemical components have a similar shape in their size distributions. Fine-particle sulphate is typically long-range transported, and was therefore selected as the model

  2. Distribution and sources of polychlorinated biphenyls in Woods Inlet, Lake Worth, Fort Worth, Texas, 2003

    USGS Publications Warehouse

    Besse, Richard E.; Van Metre, Peter C.; Wilson, Jennifer T.

    2005-01-01

    Woods Inlet is a flooded stream channel on the southern shore of Lake Worth along the western boundary of Air Force Plant 4 in Fort Worth, Texas, where elevated polychlorinated biphenyl (PCB) concentrations in sediment were detected in a previous study. In response, the U.S. Geological Survey, in cooperation with the U.S. Air Force, conducted a study in 2003 to map the extent of elevated PCB concentrations in Woods Inlet and to identify possible sources (or more specifically, source areas) of PCBs in the watershed of Woods Inlet. Three gravity cores (penetration to pre-reservoir sediment at three sites) and 17 box cores (surficial bottom sediment samples) were collected in Woods Inlet. Suspended sediment in stormwater runoff and streambed sediment were sampled in tributaries to Woods Inlet following storms. Assemblages of PCB congeners in surficial inlet sediments and suspended and streambed sediments were analyzed to indicate sources of PCBs in the inlet sediments on the basis of chemical signatures of PCBs. Woods Inlet receives runoff primarily from three tributaries: (1) Gruggs Park Creek, (2) the small unnamed creek that drains a Texas National Guard maintenance facility, called TNG Creek for this report, and (3) Meandering Road Creek. Twenty-seven of 209 possible PCB congeners were analyzed. The sum of the congeners was used as a measure of total PCB. The spatial distribution of total PCB concentrations in the inlet indicates that most PCBs are originating in the Meandering Road Creek watershed. Peak total PCB concentrations in the three gravity cores occurred at depths corresponding to sediment deposition dates of about 1960 for two of the cores and about 1980 for the third core. The magnitudes of peak total PCB concentrations in the gravity cores followed a spatial distribution generally similar to that of surficial bottom sediment concentrations. Total PCB concentrations in suspended and streambed sediment varied greatly between sites and indicated a likely

  3. Distributions, Sources, and Backward Trajectories of Atmospheric Polycyclic Aromatic Hydrocarbons at Lake Small Baiyangdian, Northern China

    PubMed Central

    Qin, Ning; Kong, Xiang-Zhen; Zhu, Ying; He, Wei; He, Qi-Shuang; Yang, Bin; Ou-Yang, Hui-Ling; Liu, Wen-Xiu; Wang, Qing-Mei; Xu, Fu-Liu

    2012-01-01

    Air samples were collected seasonally at Lake Small Baiyangdian, a shallow lake in northern China, between October 2007 and September 2008. Gas phase, particulate phase and dust fall concentrations of polycyclic aromatic hydrocarbons (PAHs) were measured using a gas chromatograph-mass spectrometer (GC-MS). The distribution and partitioning of atmospheric PAHs were studied, and the major sources were identified; the backward trajectories of air masses starting from the center of Lake Small Baiyangdian were calculated for the entire year. The following results were obtained: (1) The total concentration of 16 priority controlled PAHs (PAH16) in the gas phase was 417.2 ± 299.8 ng·m−3, in the particulate phase was 150.9 ± 99.2 ng·m−3, and in dust fall was 6930.2 ± 3206.5 ng·g−1. (2) Vehicle emission, coal combustion, and biomass combustion were the major sources in the Small Baiyangdian atmosphere and accounted for 28.9%, 45.1% and 26.0% of the total PAHs, respectively. (3) Winter was dominated by relatively greater PAHs polluted northwesterly air mass pathways. Summer showed a dominant relatively clean southern pathway, whereas the trajectories in autumn and spring might be associated with high pollution from Shanxi or Henan province. PMID:23118612

  4. Macronutrient Distribution and Dietary Sources in the Spanish Population: Findings from the ANIBES Study.

    PubMed

    Ruiz, Emma; Ávila, José Manuel; Valero, Teresa; Del Pozo, Susana; Rodriguez, Paula; Aranceta-Bartrina, Javier; Gil, Ángel; González-Gross, Marcela; Ortega, Rosa M; Serra-Majem, Lluis; Varela-Moreiras, Gregorio

    2016-03-01

    Our aim was to analyze dietary macronutrient intake and its main sources according to sex and age. Results were derived from the ANIBES ("Anthropometry, Intake and Energy Balance in Spain") cross-sectional study using a nationally-representative sample of the Spanish population (9-75 years old). Mean dietary protein intake was 74.5 ± 22.4 g/day, with meat and meat products as the main sources (33.0%). Mean carbohydrate intake was 185.4 ± 60.9 g/day and was higher in children and adolescents; grains (49%), mainly bread, were the main contributor. Milk and dairy products (23%) ranked first for sugar intake. Mean lipid intake was 78.1 ± 26.1 g/day and was higher in younger age groups; contributions were mainly from oils and fats (32.5%; olive oil 25.6%) and meat and meat products (22.0%). Lipid profiles showed relatively high monounsaturated fatty acid intake, of which olive oil contributed 38.8%. Saturated fatty acids were mainly (>70%) combined from meat and meat products, milk and dairy products and oils and fats. Polyunsaturated fatty acids were mainly from oils and fats (31.5%). The macronutrient intake and distribution in the Spanish population is far from population reference intakes and nutritional goals, especially for children and adolescents. PMID:27011202

  5. Simple and effective calculations about spectral power distributions of outdoor light sources for computer vision.

    PubMed

    Tian, Jiandong; Duan, Zhigang; Ren, Weihong; Han, Zhi; Tang, Yandong

    2016-04-01

    The spectral power distributions (SPD) of outdoor light sources are not constant over time and atmospheric conditions, which causes the appearance variation of a scene and common natural illumination phenomena, such as twilight, shadow, and haze/fog. Calculating the SPD of outdoor light sources at different time (or zenith angles) and under different atmospheric conditions is of interest to physically-based vision. In this paper, for computer vision and its applications, we propose a feasible, simple, and effective SPD calculating method based on analyzing the transmittance functions of absorption and scattering along the path of solar radiation through the atmosphere in the visible spectrum. Compared with previous SPD calculation methods, our model has less parameters and is accurate enough to be directly applied in computer vision. It can be applied in computer vision tasks including spectral inverse calculation, lighting conversion, and shadowed image processing. The experimental results of the applications demonstrate that our calculation methods have practical values in computer vision. It establishes a bridge between image and physical environmental information, e.g., time, location, and weather conditions. PMID:27137018

  6. Distribution and potential sources and sinks of copper chelators in the Sargasso Sea

    NASA Astrophysics Data System (ADS)

    Moffett, J. W.; Zika, R. G.; Brand, L. E.

    1990-01-01

    Copper speciation has been studied at an oligotrophic station in the southwestern Sargasso Sea to determine the distribution of Cu binding ligands and evaluate their potential sources and sinks. Speciation was studied using a ligand exchange/liquid-liquid partition procedure used in a previous study in Florida coastal waters [ MOFFET and ZIKA (1987a) Marine Chemistry, 21, 301-313]. Copper speciation was dominated by organic complexation at all depths studied (16-950 m). Complexation was greatest in the region of the chlorophyll maximum. In this region, speciation was dominated by two ligands or ligand classes; L 1, with K cond. = 10 13.2, concentration = 2 nM, and a weaker but more abundant ligand class, L 2 with Kincond. = 10 9.7, concentration = 80 nM. From 140 to 16 m, [Cu(II)] free/[Cu(II)] total increases by a factor of 20, due to a decrease in [L 1] to a value below the ambient Cu concentration. Exposure of water from 140 m to sunlight indicated that photochemical decomposition of L 1 may account for the decrease. Below the chlorophyll maximum there is a gradual increase in [Cu(II)] free/[Cu(II)] total suggesting that the ligands are of recent biological origin rather than derived from refractory materials. Cultures of a ubiquitous marine cyanobacterium, Synechococcus sp. produced a ligand with K cond. comparable to L 1, indicating that a biological source is plausible.

  7. Analysis of ultrasonically rotating droplet using moving particle semi-implicit and distributed point source methods

    NASA Astrophysics Data System (ADS)

    Wada, Yuji; Yuge, Kohei; Tanaka, Hiroki; Nakamura, Kentaro

    2016-07-01

    Numerical analysis of the rotation of an ultrasonically levitated droplet with a free surface boundary is discussed. The ultrasonically levitated droplet is often reported to rotate owing to the surface tangential component of acoustic radiation force. To observe the torque from an acoustic wave and clarify the mechanism underlying the phenomena, it is effective to take advantage of numerical simulation using the distributed point source method (DPSM) and moving particle semi-implicit (MPS) method, both of which do not require a calculation grid or mesh. In this paper, the numerical treatment of the viscoacoustic torque, which emerges from the viscous boundary layer and governs the acoustical droplet rotation, is discussed. The Reynolds stress traction force is calculated from the DPSM result using the idea of effective normal particle velocity through the boundary layer and input to the MPS surface particles. A droplet levitated in an acoustic chamber is simulated using the proposed calculation method. The droplet is vertically supported by a plane standing wave from an ultrasonic driver and subjected to a rotating sound field excited by two acoustic sources on the side wall with different phases. The rotation of the droplet is successfully reproduced numerically and its acceleration is discussed and compared with those in the literature.

  8. Heavy metal in surface sediments of the Liaodong Bay, Bohai Sea: distribution, contamination, and sources.

    PubMed

    Hu, Bangqi; Li, Jun; Zhao, Jingtao; Yang, John; Bai, Fenglong; Dou, Yanguang

    2013-06-01

    In an effort to assess the potential contamination and determine the environmental risks associated with heavy metals, the surface sediments in Liaodong Bay, northeast China, were systematically sampled and analyzed for the concentrations of Cu, Pb, Zn, Cr, Ni, As, and Hg. The metal enrichment factor (EF) and geoaccumulation index (I geo) were calculated to assess the anthropogenic contamination in the region. Results showed that heavy metal concentrations in the sediments generally met the criteria of China Marine Sediment Quality (GB18668-2002); however, both EF and I geo values suggested the elevation of Pb concentration in the region. Based on the effect-range classification (TEL-PEL SQGs), Cu, Pb, Ni, and As were likely to pose environment risks, and the toxic units decreased in the order: Ni > Pb > Cr > Zn > As > Cu > Hg. The spatial distribution of ecotoxicological index (mean-ERM-quotient) suggested that most of the surface sediments were "low-medium" priority zone. Multivariate analysis indicated that the sources of Cr, Ni, Zn, Cu, and Hg resulted primarily from parent rocks, and Pb or As were mainly attributed to anthropogenic sources. The results of this study would provide a useful aid for sustainable marine management in the region. PMID:23064895

  9. Harvesting, Integrating and Distributing Large Open Geospatial Datasets Using Free and Open-Source Software

    NASA Astrophysics Data System (ADS)

    Oliveira, Ricardo; Moreno, Rafael

    2016-06-01

    Federal, State and Local government agencies in the USA are investing heavily on the dissemination of Open Data sets produced by each of them. The main driver behind this thrust is to increase agencies' transparency and accountability, as well as to improve citizens' awareness. However, not all Open Data sets are easy to access and integrate with other Open Data sets available even from the same agency. The City and County of Denver Open Data Portal distributes several types of geospatial datasets, one of them is the city parcels information containing 224,256 records. Although this data layer contains many pieces of information it is incomplete for some custom purposes. Open-Source Software were used to first collect data from diverse City of Denver Open Data sets, then upload them to a repository in the Cloud where they were processed using a PostgreSQL installation on the Cloud and Python scripts. Our method was able to extract non-spatial information from a `not-ready-to-download' source that could then be combined with the initial data set to enhance its potential use.

  10. Sources and Distribution of Trace Elements in Soils Near Coal-Related Industries.

    PubMed

    Shangguan, Yuxian; Wei, Yuan; Wang, Linquan; Hou, Hong

    2016-04-01

    The degree of contamination of soil and the potential ecological risks associated with five different coal-burning industries were assessed in Shanxi Province, China. Results showed that the trace element concentrations in soil close to the coal industries were higher than those in the background soils, and the enrichment factors were >1. The potential ecological risk indexes ranged from 99 to 328 for the five coal-related industries. Results also illustrated that the trace elements were transported through the atmosphere. Concentrations of B, Hg, Mo, Pb, Se, Cr, Cu, Ni, V, Zn, and Mn were high in the area around the steel plant. Principal component analysis and redundancy analysis indicated that the sources of Se, Mo, Hg, Cd, As, Cr, B, Ni, and Cu were mainly anthropogenic, whereas Pb, V, Cu, Zn, and Mn were from natural sources. The soil Hg and Se contents were simulated by an artificial neural network model, which showed that Hg and Se in soils were from atmospheric deposits and their spatial distributions were related to the dominant wind direction. The potential ecological risk from Hg was much higher (one order of magnitude) than that from the other trace elements, which highlights the fact that it deserves urgent attention. Control of emissions from the burning of coal and other raw materials (such as iron and phosphate ores) should also be prioritized. PMID:26428004

  11. Macronutrient Distribution and Dietary Sources in the Spanish Population: Findings from the ANIBES Study

    PubMed Central

    Ruiz, Emma; Ávila, José Manuel; Valero, Teresa; del Pozo, Susana; Rodriguez, Paula; Aranceta-Bartrina, Javier; Gil, Ángel; González-Gross, Marcela; Ortega, Rosa M.; Serra-Majem, Lluis; Varela-Moreiras, Gregorio

    2016-01-01

    Our aim was to analyze dietary macronutrient intake and its main sources according to sex and age. Results were derived from the ANIBES (“Anthropometry, Intake and Energy Balance in Spain”) cross-sectional study using a nationally-representative sample of the Spanish population (9–75 years old). Mean dietary protein intake was 74.5 ± 22.4 g/day, with meat and meat products as the main sources (33.0%). Mean carbohydrate intake was 185.4 ± 60.9 g/day and was higher in children and adolescents; grains (49%), mainly bread, were the main contributor. Milk and dairy products (23%) ranked first for sugar intake. Mean lipid intake was 78.1 ± 26.1 g/day and was higher in younger age groups; contributions were mainly from oils and fats (32.5%; olive oil 25.6%) and meat and meat products (22.0%). Lipid profiles showed relatively high monounsaturated fatty acid intake, of which olive oil contributed 38.8%. Saturated fatty acids were mainly (>70%) combined from meat and meat products, milk and dairy products and oils and fats. Polyunsaturated fatty acids were mainly from oils and fats (31.5%). The macronutrient intake and distribution in the Spanish population is far from population reference intakes and nutritional goals, especially for children and adolescents. PMID:27011202

  12. Chemotaxis Increases the Residence Time of Bacteria in Granular Media Containing Distributed Contaminant Sources.

    PubMed

    Adadevoh, Joanna S T; Triolo, Sarah; Ramsburg, C Andrew; Ford, Roseanne M

    2016-01-01

    The use of chemotactic bacteria in bioremediation has the potential to increase access to, and the biotransformation of, contaminant mass within the subsurface. This laboratory-scale study aimed to understand and quantify the influence of chemotaxis on the residence times of pollutant-degrading bacteria within homogeneous treatment zones. Focus was placed on a continuous-flow sand-packed column in which a uniform distribution of naphthalene crystals created distributed sources of dissolved-phase contaminant. A 10 mL pulse of Pseudomonas putida G7, which is chemotactic to naphthalene, and Pseudomonas putida G7 Y1, a nonchemotactic mutant strain, were simultaneously introduced into the sand-packed column at equal concentrations. Breakthrough curves obtained from experiments conducted with and without naphthalene were used to quantify the effect of chemotaxis on transport parameters. In the presence of the chemoattractant, longitudinal dispersion of PpG7 increased by a factor of 3, and percent recovery decreased by 43%. In contrast, PpG7 Y1 transport was not influenced by the presence of naphthalene. The results imply that pore-scale chemotaxis responses are evident at an interstitial velocity of 1.8 m/day, which is within the range of typical groundwater flow. Within the context of bioremediation, chemotaxis may work to enhance bacterial residence times in zones of contamination, thereby improving treatment. PMID:26605857

  13. Distribution, sources and ecological risk assessment of heavy metals in surface sediments from Lake Taihu, China

    NASA Astrophysics Data System (ADS)

    Yin, Hongbin; Gao, Yongnian; Fan, Chengxin

    2011-10-01

    The distribution, sources and ecological risk of heavy metals in surface sediments from Lake Taihu were studied. Results showed that the measured heavy metals had varied spatial distribution patterns, indicating that they had complex origins and controlling factors. Pearson's correlation analysis revealed that the total phosphorus and the loss on ignition were positively correlated with the measured metals except Cd. Principal component analysis and cluster analysis demonstrated that Hg, Cu, Cr, Cd and Pb might originate from domestic sewage and industrial wastewater, whereas As predominantly originated from natural processes. Potential ecological risk indices indicated that sediment from Wuli Lake, Gonghu Bay and the Northwest Area suffered high pollution, whereas other areas of Lake Taihu were moderately polluted. A comparison of metal levels with the effects range low (ERL) and effects range median (ERM) showed that metals exceeded their corresponding ERL limit at 13.6-72.3% (72.3% for As, 52.4% for Pb, 27.7% for Cu, 22.8% for Cd, 16.0 for Hg and 13.6% for Cr) of the sites investigated. Moreover, 3.90% and 0.50% of the sites sampled exceeded the ERM thresholds for Hg and Pb, respectively.

  14. Sources and distribution of upper Pleistocene sand, Eastern United States Atlantic Shelf

    SciTech Connect

    Leschak, P.; Prusak, D.; Mazzullo, J.

    1985-02-01

    A 2-yr study of the sources and distribution of upper Pleistocene and Holocene sand on the eastern US shelf between the Bay of Fundy and Cape Hatteras reveals that 3 sand types are found on this shelf: (1) glacially transported, very angular sands, (2) fluvially transported, well-rounded sands derived from unlithified coastal plan deposits, and (3) fluvially transported, moderately angular sands derived from lithified sedimentary and crystalline rocks of the Appalachian and New England areas. For the most part, the distribution of these sand types reflects the late Pleistocene paleogeography of this shelf. Glacial sands are found in the areas of upper Pleistocene till, moraine, and outwash-plain deposits east and northeast of the Hudson Canyon; the 2 fluvial sands are found in coast-normal stripes that correspond to the ancestral paths of the many rivers that traversed this shelf during the late Pleistocene. The preservation of relict paleogeographic patterns of these sorts are an indication of diffusive transport of sand through most of this shelf. The exceptions to this are found in the shallow waters of Nantucket Shoals and Geoges Bank, where glacial sands are presently being advected to the southwest by the strong tidal currents that prevail.

  15. Simulation of a distributed current source in a linear format CFA

    NASA Astrophysics Data System (ADS)

    Pearlman, Marcus; Browning, Jim

    2015-11-01

    A fundamental limit on Crossed-Field Amplifiers (CFA) gain is beam to RF power ratio. With too much beam power, the RF signal on the slow wave circuit is ``swamped.'' It is proposed here that a controllable, distributed cathode source can be used to tailor current injection and optimize gain. In this work a linear format CFA with a meander line slow wave circuit is tested experimentally and numerically using Vsim. Simulations of the original design, which operates at 900 MHz, shows < 1dB gain at beam currents >100 mA. This beam current is higher than the capabilities of the Field Emitter Array cathodes available to the group; therefore no experimental gain was observed. To be able to compare simulation to experiment, the CFA model under study was changed to the experiment used at Northeastern University in 1991, which also uses a meander line circuit and an injected beam configuration. Direct comparisons between the simulation and this experiment are performed to validate the model. Additional simulations study the effect of different current distributions on gain, bandwidth, and efficiency. Practical considerations such as how to control the energy of the beam separately from the sole potential in order to minimize lost current to sole are also examined. This research was supported by the Air Force Office of Scientific Research and the department of Electrical and Computer Engineering at Boise State University.

  16. Spatial Distribution, Sources Apportionment and Health Risk of Metals in Topsoil in Beijing, China.

    PubMed

    Sun, Chunyuan; Zhao, Wenji; Zhang, Qianzhong; Yu, Xue; Zheng, Xiaoxia; Zhao, Jiayin; Lv, Ming

    2016-01-01

    In order to acquire the pollution feature and regularities of distribution of metals in the topsoil within the sixth ring road in Beijing, a total of 46 soil samples were collected, and the concentrations of twelve elements (Nickel, Ni, Lithium, Li, Vanadium, V, Cobalt, Co, Barium, Ba, Strontium, Sr, Chrome, Cr, Molybdenum, Mo, Copper, Cu, Cadmium, Cd, Zinc, Zn, Lead, Pb) were analyzed. Geostatistics and multivariate statistics were conducted to identify spatial distribution characteristics and sources. In addition, the health risk of the analyzed heavy metals to humans (adult) was evaluated by an U.S. Environmental Protection Agency health risk assessment model. The results indicate that these metals have notable variation in spatial scale. The concentration of Cr was high in the west and low in the east, while that of Mo was high in the north and low in the south. High concentrations of Cu, Cd, Zn, and Pb were found in the central part of the city. The average enrichment degree of Cd is 5.94, reaching the standard of significant enrichment. The accumulation of Cr, Mo, Cu, Cd, Zn, and Pb is influenced by anthropogenic activity, including vehicle exhaustion, coal burning, and industrial processes. Health risk assessment shows that both non-carcinogenic and carcinogenic risks of selected heavy metals are within the safety standard and the rank of the carcinogenic risk of the four heavy metals is Cr > Co > Ni > Cd. PMID:27447657

  17. Spatial Distribution, Sources Apportionment and Health Risk of Metals in Topsoil in Beijing, China

    PubMed Central

    Sun, Chunyuan; Zhao, Wenji; Zhang, Qianzhong; Yu, Xue; Zheng, Xiaoxia; Zhao, Jiayin; Lv, Ming

    2016-01-01

    In order to acquire the pollution feature and regularities of distribution of metals in the topsoil within the sixth ring road in Beijing, a total of 46 soil samples were collected, and the concentrations of twelve elements (Nickel, Ni, Lithium, Li, Vanadium, V, Cobalt, Co, Barium, Ba, Strontium, Sr, Chrome, Cr, Molybdenum, Mo, Copper, Cu, Cadmium, Cd, Zinc, Zn, Lead, Pb) were analyzed. Geostatistics and multivariate statistics were conducted to identify spatial distribution characteristics and sources. In addition, the health risk of the analyzed heavy metals to humans (adult) was evaluated by an U.S. Environmental Protection Agency health risk assessment model. The results indicate that these metals have notable variation in spatial scale. The concentration of Cr was high in the west and low in the east, while that of Mo was high in the north and low in the south. High concentrations of Cu, Cd, Zn, and Pb were found in the central part of the city. The average enrichment degree of Cd is 5.94, reaching the standard of significant enrichment. The accumulation of Cr, Mo, Cu, Cd, Zn, and Pb is influenced by anthropogenic activity, including vehicle exhaustion, coal burning, and industrial processes. Health risk assessment shows that both non-carcinogenic and carcinogenic risks of selected heavy metals are within the safety standard and the rank of the carcinogenic risk of the four heavy metals is Cr > Co > Ni > Cd. PMID:27447657

  18. 227Ac in the Deep South Pacific along the Peru-Tahiti GEOTRACES Transect

    NASA Astrophysics Data System (ADS)

    Hammond, D. E.; Charette, M. A.; Moore, W. S.; Henderson, P.; Sanial, V.; Kipp, L. E.; Anderson, R. F.

    2014-12-01

    227Ac (22 yr half life) diffuses from sediment and is mixed vertically and horizontally as it decays, providing a distribution that can be used to infer transport rates for other solutes in the deep ocean. Profiles were collected during the fall of 2013 at 19 stations along the US Peru-Tahiti GEOTRACES transect by pumping water through acrylic cartridges impregnated with MnO2, to trap both Ac and Ra. Because extraction efficiency has been found to vary in past efforts, two cartridges were deployed in series to allow estimation of extraction efficiency for each sample. While analytical work is still in progress, an analysis of preliminary results indicates several features of interest: 1. Cartridge extraction efficiency (based on 25 replicates) for Ac was approximately 0.7±0.1, quite good given the high pump rate through the fibers (~6.5 L/min). 2. Profiles showed an increase toward the bottom from activities of ~0.3 dpm/m3 at 2000 m (close to expected 231Pa parent activity) to >0.9 dpm/m3 near the bottom. 3. Some isolated maxima appear near 2500 m, west of the East Pacific Rise, which may represent modest input of Ac from hydrothermal sources. In addition to dissolved Ac, there is particulate Ac associated with the Fe rich neutrally buoyant plume particles. Estimation of transport rates will be done once the analyses are completed.

  19. Current density distributions and sputter marks in electron cyclotron resonance ion sources

    SciTech Connect

    Panitzsch, Lauri; Peleikis, Thies; Boettcher, Stephan; Stalder, Michael; Wimmer-Schweingruber, Robert F.

    2013-01-15

    Most electron cyclotron resonance ion sources use hexapolar magnetic fields for the radial confinement of the plasma. The geometry of this magnetic structure is then-induced by charged particles-mapped onto the inner side of the plasma electrode via sputtering and deposition. The resulting structures usually show two different patterns: a sharp triangular one in the central region which in some cases is even sputtered deep into the material (referred to as thin groove or sharp structure), and a blurred but still triangular-like one in the surroundings (referred to as broad halo). Therefore, both patterns seem to have different sources. To investigate their origins we replaced the standard plasma electrode by a custom-built plasma electrode acting as a planar, multi-segment current-detector. For different biased disc voltages, detector positions, and source biases (referred to the detector) we measured the electrical current density distributions in the plane of the plasma electrode. The results show a strong and sharply confined electron population with triangular shape surrounded by less intense and spatially less confined ions. Observed sputter- and deposition marks are related to the analysis of the results. Our measurements suggest that the two different patterns (thin and broad) indeed originate from different particle populations. The thin structures seem to be caused by the hot electron population while the broad marks seem to stem from the medium to highly charged ions. In this paper we present our measurements together with theoretical considerations and substantiate the conclusions drawn above. The validity of these results is also discussed.

  20. Distribution, source characterization and inventory of perfluoroalkyl substances in Taihu Lake, China.

    PubMed

    Guo, Changsheng; Zhang, Yuan; Zhao, Xin; Du, Ping; Liu, Sisi; Lv, Jiapei; Xu, Fengxia; Meng, Wei; Xu, Jian

    2015-05-01

    The levels, distribution, possible sources, and inventory of perfluoroalkyl acids (PFAAs) in the eutrophic freshwater Taihu Lake, East China were investigated in this study. Among the target 11 PFAAs, perfluorooctanoic acid (PFOA) (2.15-73.9 ng L(-1)) and perfluorohexanoic acid (PFHxA) (sources. It indicated that the majority of pollutants was from direct emissions from manufacturing processes. The PFOA/PFNA ratios between 1.7 and 56.8 in surface water suggested the influence of secondary sources such as the degradation of volatile precursor substances. Given the high ratios of PFHpA/PFOA (0.05-7.93), it also indicated the influence from atmospheric deposition to the epilimnion. The predicted environmental concentrations were calculated from European Union system for the evaluation of substances model (EUSES). As expected, the predicted environmental concentration (PEC) of PFOS in sediment fit well to the monitored level of PFOS in this region, and the inventory of ΣPFCA and PFOS were estimated to be 989 kg and 646 kg in Taihu Lake. PMID:25725312

  1. Distribution and sources of lipid compound series in sediment cores of the southern South China Sea.

    PubMed

    Tahir, N Mohd; Pang, S Y; Simoneit, B R T

    2015-05-01

    Three short sediment cores from inner continental shelf of the southern South China Sea (5-50 km) off Terengganu were analyzed for lipid contents (i.e., homologous aliphatic compounds and sterols) using gas chromatography-mass spectrometry. The concentrations of the total aliphatic hydrocarbons (TAHs) ranged from 0.152 to 6.91 μg/g dry weight. The n-alkane distribution was from nC₁₃ to nC₃₆, with a carbon preference index (CPI₁₃₋₃₅) from 1.08 to 4.28 and a carbon number maximum (Cmax), depending on a sample, at 31 or 18. In addition, a strong odd-to-even carbon number predominance was observed in nC₂₅-nC₃₅ range. The distribution of the n-alkanoic acids and n-alkanols in all samples exhibited an even-to-odd carbon number predominance and ranged from C₁₀ to C₂₆ and from C₁₂ to C₃₄, respectively. The n-alkanols were dominated by the long-chain homologs with Cmax at 22; on the other hand, the n-alkanoic acid distributions showed a predominance of short-chain homologs with a Cmax at 16. The total sterol concentrations ranged from 0.41 to 3.57 μg/g dry weight. Cholesterol was most abundant at the offshore stations, whereas sitosterol was dominant at near-shore station. Pentacyclic triterpenoids such as friedelin and taraxerol α- and β-amyrins, which are known biomarkers for higher plants, were detected at all stations with a dilution trend offshore. In conclusion, the marine sediments off southern Terengganu can still be considered uncontaminated, where the compound sources are biogenic from terrestrial plants superimposed with a marine productivity input. PMID:25752627

  2. Modeling the Global Distribution of Plasma Parameters on Coronal Source Surface for Different Solar Phases Using 1AU Observations

    NASA Astrophysics Data System (ADS)

    Yang, Y.; Shen, F.; Feng, X.

    2015-10-01

    In this paper, we have developed an empirical model of the global distribution of plasma parameters on the coronal source surface (at 2.5 solar radii (Rs) in our study) by analyzing observations from Ulysses and OMNI data. We use this model to construct the global map of source surface plasma for four typical Carrington Rotations (CRs) during different phases of solar activity, and analyze the basic characteristics of the distribution. A simple validation of the model is made by comparing the density and velocity distribution with the pB-inversed density and Wang-Sheeley-Arge (WSA) model velocity. The preliminary results show that our model gives reasonable large scale distribution of source surface plasma parameters at different phases of solar activity.

  3. Trace elements in particulate matter from metropolitan regions of Northern China: Sources, concentrations and size distributions.

    PubMed

    Pan, Yuepeng; Tian, Shili; Li, Xingru; Sun, Ying; Li, Yi; Wentworth, Gregory R; Wang, Yuesi

    2015-12-15

    Public concerns over airborne trace elements (TEs) in metropolitan areas are increasing, but long-term and multi-site observations of size-resolved aerosol TEs in China are still lacking. Here, we identify highly elevated levels of atmospheric TEs in megacities and industrial sites in a Beijing-Tianjin-Hebei urban agglomeration relative to background areas, with the annual mean values of As, Pb, Ni, Cd and Mn exceeding the acceptable limits of the World Health Organization. Despite the spatial variability in concentrations, the size distribution pattern of each trace element was quite similar across the region. Crustal elements of Al and Fe were mainly found in coarse particles (2.1-9 μm), whereas the main fraction of toxic metals, such as Cu, Zn, As, Se, Cd and Pb, was found in submicron particles (<1.1 μm). These toxic metals were enriched by over 100-fold relative to the Earth's crust. The size distributions of Na, Mg, K, Ca, V, Cr, Mn, Ni, Mo and Ba were bimodal, with two peaks at 0.43-0.65 μm and 4.7-5.8 μm. The combination of the size distribution information, principal component analysis and air mass back trajectory model offered a robust technique for distinguishing the main sources for airborne TEs, e.g., soil dust, fossil fuel combustion and industrial emissions, at different sites. In addition, higher elemental concentrations coincided with westerly flow, indicating that polluted soil and fugitive dust were major sources of TEs on the regional scale. However, the contribution of coal burning, iron industry/oil combustion and non-ferrous smelters to atmospheric metal pollution in Northern China should be given more attention. Considering that the concentrations of heavy metals associated with fine particles in the target region were significantly higher than those in other Asian sites, the implementations of strict environmental standards in China are required to reduce the amounts of these hazardous pollutants released into the atmosphere. PMID

  4. FEMTOSECOND TIMING DISTRIBUTION AND CONTROL FOR NEXT GENERATION ACCELERATORS AND LIGHT SOURCES

    SciTech Connect

    Chen, Li-Jin

    2014-03-31

    Femtosecond Timing Distribution At LCLS Free-electron-lasers (FEL) have the capability of producing high photon flux from the IR to the hard x-ray wavelength range and to emit femtosecond and eventually even at-tosecond pulses. This makes them an ideal tool for fundamental as well as applied re-search. Timing precision at the Stanford Linear Coherent Light Source (LCLS) between the x-ray FEL (XFEL) and ultrafast optical lasers is currently no better than 100 fs RMS. Ideally this precision should be much better and could be limited only by the x-ray pulse duration, which can be as short as a few femtoseconds. An increasing variety of science problems involving electron and nuclear dynamics in chemical and material systems will become accessible as the timing improves to a few femtoseconds. Advanced methods of electron beam conditioning or pulse injection could allow the FEL to achieve pulse durations less than one femtosecond. The objec-tive of the work described in this proposal is to set up an optical timing distribution sys-tem based on modelocked Erbium doped fiber lasers at LCLS facility to improve the timing precision in the facility and allow time stamping with a 10 fs precision. The primary commercial applications for optical timing distributions systems are seen in the worldwide accelerator facilities and next generation light sources community. It is reasonable to expect that at least three major XFELs will be built in the next decade. In addition there will be up to 10 smaller machines, such as FERMI in Italy and Maxlab in Sweden, plus the market for upgrading already existing facilities like Jefferson Lab. The total market is estimated to be on the order of a 100 Million US Dollars. The company owns the exclusive rights to the IP covering the technology enabling sub-10 fs synchronization systems. Testing this technology, which has set records in a lab environment, at LCLS, hence in a real world scenario, is an important corner stone of bringing the

  5. The refrigeration and cryogenic distribution system for the shortpulse x-ray source

    SciTech Connect

    Green, Michael A.; Corlett, John N.

    2002-10-20

    This report describes the essential elements of the cryogenic system. The cryogenic distribution system starts at the level of the linac superconducting RF cavities [1] and moves out through the cryogenic piping to the liquid helium refrigeration plant that will be used to cool the RF cavities and the undulator magnets. For this report, the cryogenic distribution system and cryogenic refrigerator includes the following elements: (1) The piping within the linac cryogenic modules will influence the heat transfer through the super-fluid helium from the outer surface of the TESLA niobium cavity and the liquid to gas interface within the horizontal header pipe where the superfluid helium boils. This piping determines the final design of the linac cryogenic module. (2) The acceptable pressure drops determine the supply and return piping dimensions. (3) The helium distribution system is determined by the need to cool down and warm up the various elements in the light source. (4) The size of the cryogenic plant is determined by the heat loads and the probable margin of error on those heat loads. Since the final heat loads are determined by the acceleration gradient in the cavities, a linac with five cryogenic modules will be compared to a linac with only four cryogenic modules. The design assumes that all cryogenic elements in the facility will be cooled using a common cryogenic plant. To minimize vibration effects on the beam lines, this plant is assumed to be located some distance from the synchrotron light beam lines. All of the cryogenic elements in the facility will be attached to the helium refrigeration system through cryogenic transfer lines. The largest single cryogenic load is the main linac, which consists of four or five cryogenic modules depending on the design gradient for the cavities in the linac section. The second largest heat load comes from the cryogenic modules that contain the transverse deflecting RF cavities. The injector linac is the third largest

  6. Quantifying the uncertainty of nonpoint source attribution in distributed water quality models: A Bayesian assessment of SWAT's sediment export predictions

    NASA Astrophysics Data System (ADS)

    Wellen, Christopher; Arhonditsis, George B.; Long, Tanya; Boyd, Duncan

    2014-11-01

    Spatially distributed nonpoint source watershed models are essential tools to estimate the magnitude and sources of diffuse pollution. However, little work has been undertaken to understand the sources and ramifications of the uncertainty involved in their use. In this study we conduct the first Bayesian uncertainty analysis of the water quality components of the SWAT model, one of the most commonly used distributed nonpoint source models. Working in Southern Ontario, we apply three Bayesian configurations for calibrating SWAT to Redhill Creek, an urban catchment, and Grindstone Creek, an agricultural one. We answer four interrelated questions: can SWAT determine suspended sediment sources with confidence when end of basin data is used for calibration? How does uncertainty propagate from the discharge submodel to the suspended sediment submodels? Do the estimated sediment sources vary when different calibration approaches are used? Can we combine the knowledge gained from different calibration approaches? We show that: (i) despite reasonable fit at the basin outlet, the simulated sediment sources are subject to uncertainty sufficient to undermine the typical approach of reliance on a single, best fit simulation; (ii) more than a third of the uncertainty of sediment load predictions may stem from the discharge submodel; (iii) estimated sediment sources do vary significantly across the three statistical configurations of model calibration despite end-of-basin predictions being virtually identical; and (iv) Bayesian model averaging is an approach that can synthesize predictions when a number of adequate distributed models make divergent source apportionments. We conclude with recommendations for future research to reduce the uncertainty encountered when using distributed nonpoint source models for source apportionment.

  7. The source and distribution of thermogenic dissolved organic matter in the ocean

    NASA Astrophysics Data System (ADS)

    Dittmar, T.; Suryaputra, I. G. N. A.; Paeng, J.

    2009-04-01

    Thermogenic organic matter (ThOM) is abundant in the environment. ThOM is produced at elevated temperature and pressure in deep sediments and earth's crust, and it is also a residue of fossil fuel and biomass burning ("black carbon"). Because of its refractory character, it accumulates in soils and sediments and, therefore, may sequester carbon from active cycles. It was hypothesized that a significant component of marine dissolved organic matter (DOM) might be thermogenic. Here we present a detailed data set on the distribution of thermogenic DOM in major water masses of the deep and surface ocean. In addition, several potential sources of thermogenic DOM to the ocean were investigated: active seeps of brine fluids in the deep Gulf of Mexico, rivers, estuaries and submarine groundwaters. Studies on deep-sea hydrothermal vents and aerosol deposition are ongoing. All DOM samples were isolated from seawater via solid phase extraction (SPE-DOM). ThOM was quantified in the extracts as benzene-polycarboxylic acids (BPCAs) after nitric acid oxidation via high-performance liquid chromatography and diode array detection (HPLC-DAD). BPCAs are produced exclusively from fused ring systems and are therefore unambiguous molecular tracers for ThOM. In addition to BPCA determination, the molecular composition and structure of ThOM was characterized in detail via ultrahigh resolution mass spectrometry (FT-ICR-MS). All marine and river DOM samples yielded significant amounts of BPCAs. The cold seep system in the deep Gulf of Mexico, but also black water rivers (like the Suwannee River) were particularly rich in ThOM. Up to 10% of total dissolved organic carbon was thermogenic in both systems. The most abundant BPCA was benzene-pentacarboxylic acid (B5CA). The molecular composition of BPCAs and the FT-ICR-MS data indicate a relatively small number (5-8) of fused aromatic rings per molecule. Overall, the molecular BPCA patterns were very similar independent of the source of Th

  8. DUSTMS-D: DISPOSAL UNIT SOURCE TERM - MULTIPLE SPECIES - DISTRIBUTED FAILURE DATA INPUT GUIDE.

    SciTech Connect

    SULLIVAN, T.M.

    2006-01-01

    Performance assessment of a low-level waste (LLW) disposal facility begins with an estimation of the rate at which radionuclides migrate out of the facility (i.e., the source term). The focus of this work is to develop a methodology for calculating the source term. In general, the source term is influenced by the radionuclide inventory, the wasteforms and containers used to dispose of the inventory, and the physical processes that lead to release from the facility (fluid flow, container degradation, wasteform leaching, and radionuclide transport). Many of these physical processes are influenced by the design of the disposal facility (e.g., how the engineered barriers control infiltration of water). The complexity of the problem and the absence of appropriate data prevent development of an entirely mechanistic representation of radionuclide release from a disposal facility. Typically, a number of assumptions, based on knowledge of the disposal system, are used to simplify the problem. This has been done and the resulting models have been incorporated into the computer code DUST-MS (Disposal Unit Source Term-Multiple Species). The DUST-MS computer code is designed to model water flow, container degradation, release of contaminants from the wasteform to the contacting solution and transport through the subsurface media. Water flow through the facility over time is modeled using tabular input. Container degradation models include three types of failure rates: (a) instantaneous (all containers in a control volume fail at once), (b) uniformly distributed failures (containers fail at a linear rate between a specified starting and ending time), and (c) gaussian failure rates (containers fail at a rate determined by a mean failure time, standard deviation and gaussian distribution). Wasteform release models include four release mechanisms: (a) rinse with partitioning (inventory is released instantly upon container failure subject to equilibrium partitioning (sorption) with

  9. Distributional patterns of arsenic concentrations in contaminant plumes offer clues to the source of arsenic in groundwater at landfills

    USGS Publications Warehouse

    Harte, Philip T.

    2015-01-01

    The distributional pattern of dissolved arsenic concentrations from landfill plumes can provide clues to the source of arsenic contamination. Under simple idealized conditions, arsenic concentrations along flow paths in aquifers proximal to a landfill will decrease under anthropogenic sources but potentially increase under in situ sources. This paper presents several conceptual distributional patterns of arsenic in groundwater based on the arsenic source under idealized conditions. An example of advanced subsurface mapping of dissolved arsenic with geophysical surveys, chemical monitoring, and redox fingerprinting is presented for a landfill site in New Hampshire with a complex flow pattern. Tools to assist in the mapping of arsenic in groundwater ultimately provide information on the source of contamination. Once an understanding of the arsenic contamination is achieved, appropriate remedial strategies can then be formulated.

  10. Complex cell geometry and sources distribution model for Monte Carlo single cell dosimetry with iodine 125 radioimmunotherapy

    NASA Astrophysics Data System (ADS)

    Arnaud, F. X.; Paillas, S.; Pouget, J. P.; Incerti, S.; Bardiès, M.; Bordage, M. C.

    2016-01-01

    In cellular dosimetry, common assumptions consider concentric spheres for nucleus and cell and uniform radionuclides distribution. These approximations do not reflect reality, specially in the situation of radioimmunotherapy with Auger emitters, where very short-ranged electrons induce hyper localised energy deposition. A realistic cellular dosimetric model was generated to give account of the real geometry and activity distribution, for non-internalizing and internalizing antibodies (mAbs) labelled with Auger emitter I-125. The impact of geometry was studied by comparing the real geometry obtained from confocal microscopy for both cell and nucleus with volume equivalent concentric spheres. Non-uniform and uniform source distributions were considered for each mAbs distribution. Comparisons in terms of mean deposited energy per decay, energy deposition spectra and energy-volume histograms were calculated using Geant4. We conclude that realistic models are needed, especially when energy deposition is highly non-homogeneous due to source distribution.

  11. NOTE: A Monte Carlo study of dose rate distribution around the specially asymmetric CSM3-a 137Cs source

    NASA Astrophysics Data System (ADS)

    Pérez-Calatayud, J.; Lliso, F.; Ballester, F.; Serrano, M. A.; Lluch, J. L.; Limami, Y.; Puchades, V.; Casal, E.

    2001-07-01

    The CSM3 137Cs type stainless-steel encapsulated source is widely used in manually afterloaded low dose rate brachytherapy. A specially asymmetric source, CSM3-a, has been designed by CIS Bio International (France) substituting the eyelet side seed with an inactive material in the CSM3 source. This modification has been done in order to allow a uniform dose level over the upper vaginal surface when this `linear' source is inserted at the top of the dome vaginal applicators. In this study the Monte Carlo GEANT3 simulation code, incorporating the source geometry in detail, was used to investigate the dosimetric characteristics of this special CSM3-a 137Cs brachytherapy source. The absolute dose rate distribution in water around this source was calculated and is presented in the form of an along-away table. Comparison of Sievert integral type calculations with Monte Carlo results are discussed.

  12. Distribution of naphthalenes in crude oils from the Java Sea: Source and maturation effects

    SciTech Connect

    Radke, M. ); Rullkoetter, J. ); Vriend, S.P. )

    1994-09-01

    Amounts and distributions of C[sub 1]-C[sub 3] naphthalenes and cadalene were determined by capillary gas chromatography in sixty crude oil samples from the Java Sea, southeast Asia and in a sample of Talang Akar (Oligocene) resinite supposed to be a major contributor of hydrocarbons to oils in that area. Maturity of the oils was assessed by the Methylphenanthrene Index (MPI-1). Source effects discovered by scatterplots were scrutinized by Principal Component Analysis (PCA). Based on empirical relationships with C[sub 27]-C[sub 29] steranes (measured by gas chromatography-mass spectrometry), dimethylnaphthalenes in oils from the Ardjuna and Jatibarang (sub-)basins are mainly derived from terrestrial sources. Transition to a marine depositional environment in the Sunda basin, as indicated by a decrease in C[sub 29] sterane relative abundance from 70 to 30%, results in a decrease of total dimethylnaphthalene (DMN) concentrations from 20 to less than 3 mg/g oil. This is due, mainly, to a decrease in the concentration of the dominant 1,6-DMN. Thus, terrestrial Ardjuna or Jatibarang oils rich in 1,6-DMN (2-15 mg/g oil) are readily discriminated from marine Sunda oils (0.2-2 mg 1,6-DMN/g oil). Resinite of the Talang Akar type (1.4 mg 1,6-DMN/g total organic matter [TOM]) appears to be a significant contributor of 1,6-DMN to oils in the Ardjuna basin. Terrestrial affinities are inferred also for cadalene from concentration levels that are higher in terrestrial oils (1-3 mg/g oil) and Talang Akar resinite (6 mg/g TOM) than in the marine oils (0.1-1 mg/g oil). Ardjuna basin oils have the highest concentrations of cadalene, hence supporting resinite of the Talang Akar type as a possible source. However, 1,6-DMN and cadalene are likely to be derived from different terrestrial organic matter sources, because they load on different factors in PCA.

  13. A distributed database system for sharing geological information using free and open source software

    NASA Astrophysics Data System (ADS)

    Nemoto, T.; Masumoto, S.; Nonogaki, S.; Raghavan, V.

    2013-12-01

    Recently, geological information, such as borehole data and geological maps, and seismic, volcanic or landslide hazard maps are published on the Internet by the national government, local governments, and research institutes in Japan. Most web systems that deliver such geological information consist of a centralized database, which are located and maintained in one location. It is easier to manage the centralized database system because all data resides in a single location. However, if the database breaks, the web service will not be available. In the present study, a distributed database system has been developed to continue delivering geological information even if a database breaks. The distributed database system has an advantage that the system remains available although an individual database is down. All the software used to construct the system is free and open source software. PostgreSQL and pgpool-II are utilized to construct a distributed database. PostgreSQL is a powerful relational database management system. Pgpool-II has a function for management of multiple PostgreSQL servers. OpenLayers is used for the web map clients. Replication and Parallel query modes with pgpool-II are utilized for distribution of a database. It is possible to create a real-time backup on 2 or more PostgreSQL clusters by replication mode. If a database breaks, the backup database will works to continue delivering geological information. Data can be split among multiple servers by using parallel query mode. The rules to send partitioned data to an appropriate cluster are contained in the System Database. If large-scale data is searched, the overall execution time will be reduced. The prototype for sharing 1500 borehole data has been successfully implemented by combination of PostgreSQL and pgpool-II on Linux server. Further development and improvement of the system are necessary to manage and analyze various spatial data in addition to borehole data. This study was supported

  14. Evaluation of brachytherapy lung implant dose distributions from photon-emitting sources due to tissue heterogeneities

    SciTech Connect

    Yang Yun; Rivard, Mark J.

    2011-11-15

    Purpose: Photon-emitting brachytherapy sources are used for permanent implantation to treat lung cancer. However, the current brachytherapy dose calculation formalism assumes a homogeneous water medium without considering the influence of radiation scatter or tissue heterogeneities. The purpose of this study was to determine the dosimetric effects of tissue heterogeneities for permanent lung brachytherapy. Methods: The MCNP5 v1.40 radiation transport code was used for Monte Carlo (MC) simulations. Point sources with energies of 0.02, 0.03, 0.05, 0.1, 0.2, and 0.4 MeV were simulated to cover the range of pertinent brachytherapy energies and to glean dosimetric trends independent of specific radionuclide emissions. Source positions from postimplant CT scans of five patient implants were used for source coordinates, with dose normalized to 200 Gy at the center of each implant. With the presence of fibrosis (around the implant), cortical bone, lung, and healthy tissues, dose distributions and {sub PTV}DVH were calculated using the MCNP *FMESH4 tally and the NIST mass-energy absorption coefficients. This process was repeated upon replacing all tissues with water. For all photon energies, 10{sup 9} histories were simulated to achieve statistical errors (k = 1) typically of 1%. Results: The mean PTV doses calculated using tissue heterogeneities for all five patients changed (compared to dose to water) by only a few percent over the examined photon energy range, as did PTV dose at the implant center. The {sub PTV}V{sub 100} values were 81.2%, 90.0% (as normalized), 94.3%, 93.9%, 92.7%, and 92.2% for 0.02, 0.03, 0.05, 0.1, 0.2, and 0.4 MeV source photons, respectively. Relative to water, the maximum bone doses were higher by factors of 3.7, 5.1, 5.2, 2.4, 1.2, and 1.0 The maximum lung doses were about 0.98, 0.94, 0.91, 0.94, 0.97, and 0.99. Relative to water, the maximum healthy tissue doses at the mediastinal position were higher by factors of 9.8, 2.2, 1.3, 1.1, 1.1, and

  15. Sources and distribution of organic matter in a river-dominated estuary (Winyah Bay, SC, USA)

    NASA Astrophysics Data System (ADS)

    Goñi, Miguel A.; Teixeira, Maria J.; Perkey, David W.

    2003-08-01

    The sources and distribution of organic matter (OM) in surface waters and sediments from Winyah Bay (South Carolina, USA) were investigated using a variety of analytical techniques, including elemental, stable isotope and organic biomarker analyses. Several locations along the estuary salinity gradient were sampled during four different periods of contrasting river discharge and tidal range. The dissolved organic carbon (DOC) concentrations of surface waters ranged from 7 mg l -1 in the lower bay stations closest to the ocean to 20 mg l -1 in the river and upper bay samples. There was a general linear relationship between DOC concentrations and salinity in three of the four sampling periods. In contrast, particulate organic carbon (POC) concentrations were significantly lower (0.1-3 mg l -1) and showed no relationship with salinity. The high molecular weight dissolved OM (HMW DOM) isolated from selected water samples collected along the bay displayed atomic carbon:nitrogen ratios ([C/N]a) and stable carbon isotopic compositions of organic carbon ( δ13C OC) that ranged from 10 to 30 and from -28 to -25‰, respectively. Combined, such compositions indicate that in most HMW DOM samples, the majority of the OM originates from terrigenous sources, with smaller contributions from riverine and estuarine phytoplankton. In contrast, the [C/N]a ratios of particulate OM (POM) samples varied significantly among the collection periods, ranging from low values of ˜5 to high values of >20. Overall, the trends in [C/N]a ratios indicated that algal sources of POM were most important during the early and late summer, whereas terrigenous sources dominated in the winter and early spring. In Winyah Bay bottom sediments, the concentrations of the mineral-associated OM were positively correlated with sediment surface area. The [C/N]a ratios and δ13C OC compositions of the bulk sedimentary OM ranged from 5 to 45 and from -28 to -23‰, respectively. These compositions were consistent

  16. Extended Tonks-Langmuir-type model with non-Boltzmann-distributed electrons and cold ion sources

    NASA Astrophysics Data System (ADS)

    Kamran, M.; Kuhn, S.; Tskhakaya, D. D.; Khan, M.; Khan

    2013-04-01

    A general formalism for calculating the potential distribution Φ(z) in the quasineutral region of a new class of plane Tonks-Langmuir (TL)-type bounded-plasma-system (BPS) models differing from the well-known `classical' TL model (Tonks, L. and Langmuir, I. 1929 A general theory of the plasma of an arc. Phys. Rev. 34, 876) by allowing for arbitrary (but still cold) ion sources and arbitrary electron distributions is developed. With individual particles usually undergoing microscopic collision/sink/source (CSS) events, extensive use is made here of the basic kinetic-theory concept of `CSS-free trajectories' (i.e., the characteristics of the kinetic equation). Two types of electron populations, occupying the `type-t' and `type-p' domains of electron phase space, are distinguished. By definition, the type-t and type-p domains are made up of phase points lying on type-t (`trapped') CSS-free trajectories (not intersecting the walls and closing on themselves) and type-p (`passing') ones (starting at one of the walls and ending at the other). This work being the first step, it is assumed that ɛ ≡ λ D /l -> 0+ (where λ D and l are a typical Debye length and a typical ionization length respectively) so that the system exhibits a finite quasineutral `plasma' region and two infinitesimally thin `sheath' regions associated with the `sheath-edge singularities' | dΦ/dz| z->+/-zs -> ∞. The potential in the plasma region is required to satisfy a plasma equation (quasineutrality condition) of the form n i {Φ} = n e (Φ), where the electron density n e (Φ) is given and the ion density n i {Φ} is expressed in terms of trajectory integrals of the ion kinetic equation, with the ions produced by electron-impact ionization of cold neutrals. While previous TL-type models were characterized by electrons diffusing under the influence of frequent collisions with the neutral background particles and approximated by Maxwellian (Riemann, K.-U. 2006 Plasma-sheath transition in the

  17. Level structure and reflection asymmetric shape in sup 223 Ac

    SciTech Connect

    Sheline, R.K.; Liang, C.F.; Paris, P. )

    1990-07-20

    Mass separated sources of {sup 227}Pa (separated as PaF{sub 4}{sup +} ions) were used to study the level structure of {sup 223}Ac following alpha decay. The levels in {sup 223}Ac are interpreted as K = 5/2{sup {plus minus}} parity doublet bands which occur naturally in reflection asymmetric models and the multiphonon octupole model. The anomalous structure of the K = 3/2{sup {minus}} band is explained in terms of Coriolis coupling. The low lying parity doublet bands in {sup 223}Ac, {sup 225}Ac, and {sup 227}Ac are compared and contrasted.

  18. Trends in the Family Income Distribution by Race/Ethnicity and Income Source, 1988–2009

    PubMed Central

    Monnat, Shannon M.; Raffalovich, Lawrence E.; Tsao, Hui-shien

    2015-01-01

    The recent dramatic rise in U.S. income inequality has prompted a great deal of research on trends in overall family income and changes in sources of family income, especially among the highest income earners. However, less is known about changes in sources of income among the bottom 99% or about racial/ethnic differences in those trends. The present research contributes to the literatures on income trends and racial economic inequality by using family-level data from the 1988–2009 Current Population Survey to examine changes in overall family income and the proportion of income coming from employment, property/assets, and transfers across five different levels of family income for white-, black, and Hispanic-headed families. We find that at all income levels above the 25th percentile, employment income is by far the largest contributor to family income for all racial/ethnic groups. Employment income trended upward over the period in both real dollars and as a percentage of total family income. In this respect, white, black and Hispanic families are remarkably similar. The racial gap in total family income has remained fairly stable over the period, but this trend conceals a narrowing of racial differences in property income, mostly as a function of the decline in property income among whites, a widening of racial differences in transfer income among the bottom 25%, and a widening of racial differences in employment income, particularly at the top of the family income distribution. Income accrued from wealth is a very small component of overall family income for all three racial groups, even for the highest-income families (top 1%). PMID:26180265

  19. Relation Between Sprite Distribution and Source Locations of VHF Pulses Derived From JEM- GLIMS Measurements

    NASA Astrophysics Data System (ADS)

    Sato, Mitsuteru; Mihara, Masahiro; Ushio, Tomoo; Morimoto, Takeshi; Kikuchi, Hiroshi; Adachi, Toru; Suzuki, Makoto; Yamazaki, Atsushi; Takahashi, Yukihiro

    2015-04-01

    JEM-GLIMS is continuing the comprehensive nadir observations of lightning and TLEs using optical instruments and electromagnetic wave receivers since November 2012. For the period between November 20, 2012 and November 30, 2014, JEM-GLIMS succeeded in detecting 5,048 lightning events. A total of 567 events in 5,048 lightning events were TLEs, which were mostly elves events. To identify the sprite occurrences from the transient optical flash data, it is necessary to perform the following data analysis: (1) a subtraction of the appropriately scaled wideband camera data from the narrowband camera data; (2) a calculation of intensity ratio between different spectrophotometer channels; and (3) an estimation of the polarization and CMC for the parent CG discharges using ground-based ELF measurement data. From a synthetic comparison of these results, it is confirmed that JEM-GLISM succeeded in detecting sprite events. The VHF receiver (VITF) onboard JEM-GLIMS uses two patch-type antennas separated by a 1.6-m interval and can detect VHF pulses emitted by lightning discharges in the 70-100 MHz frequency range. Using both an interferometric technique and a group delay technique, we can estimate the source locations of VHF pulses excited by lightning discharges. In the event detected at 06:41:15.68565 UT on June 12, 2014 over central North America, sprite was distributed with a horizontal displacement of 20 km from the peak location of the parent lightning emission. In this event, a total of 180 VHF pulses were simultaneously detected by VITF. From the detailed data analysis of these VHF pulse data, it is found that the majority of the source locations were placed near the area of the dim lightning emission, which may imply that the VHF pulses were associated with the in-cloud lightning current. At the presentation, we will show detailed comparison between the spatiotemporal characteristics of sprite emission and source locations of VHF pulses excited by the parent lightning

  20. Realtime Gas Emission Monitoring at Hazardous Sites Using a Distributed Point-Source Sensing Infrastructure.

    PubMed

    Manes, Gianfranco; Collodi, Giovanni; Gelpi, Leonardo; Fusco, Rosanna; Ricci, Giuseppe; Manes, Antonio; Passafiume, Marco

    2016-01-01

    This paper describes a distributed point-source monitoring platform for gas level and leakage detection in hazardous environments. The platform, based on a wireless sensor network (WSN) architecture, is organised into sub-networks to be positioned in the plant's critical areas; each sub-net includes a gateway unit wirelessly connected to the WSN nodes, hence providing an easily deployable, stand-alone infrastructure featuring a high degree of scalability and reconfigurability. Furthermore, the system provides automated calibration routines which can be accomplished by non-specialized maintenance operators without system reliability reduction issues. Internet connectivity is provided via TCP/IP over GPRS (Internet standard protocols over mobile networks) gateways at a one-minute sampling rate. Environmental and process data are forwarded to a remote server and made available to authenticated users through a user interface that provides data rendering in various formats and multi-sensor data fusion. The platform is able to provide real-time plant management with an effective; accurate tool for immediate warning in case of critical events. PMID:26805832

  1. Realtime Gas Emission Monitoring at Hazardous Sites Using a Distributed Point-Source Sensing Infrastructure

    PubMed Central

    Manes, Gianfranco; Collodi, Giovanni; Gelpi, Leonardo; Fusco, Rosanna; Ricci, Giuseppe; Manes, Antonio; Passafiume, Marco

    2016-01-01

    This paper describes a distributed point-source monitoring platform for gas level and leakage detection in hazardous environments. The platform, based on a wireless sensor network (WSN) architecture, is organised into sub-networks to be positioned in the plant’s critical areas; each sub-net includes a gateway unit wirelessly connected to the WSN nodes, hence providing an easily deployable, stand-alone infrastructure featuring a high degree of scalability and reconfigurability. Furthermore, the system provides automated calibration routines which can be accomplished by non-specialized maintenance operators without system reliability reduction issues. Internet connectivity is provided via TCP/IP over GPRS (Internet standard protocols over mobile networks) gateways at a one-minute sampling rate. Environmental and process data are forwarded to a remote server and made available to authenticated users through a user interface that provides data rendering in various formats and multi-sensor data fusion. The platform is able to provide real-time plant management with an effective; accurate tool for immediate warning in case of critical events. PMID:26805832

  2. Distributed multiple-anodes benthic microbial fuel cell as reliable power source for subsea sensors

    NASA Astrophysics Data System (ADS)

    Liu, Bingchuan; Weinstein, Alyssa; Kolln, Michael; Garrett, Caleb; Wang, Lei; Bagtzoglou, Amvrossios; Karra, Udayarka; Li, Yan; Li, Baikun

    2015-07-01

    A new type distributed benthic microbial fuel cell (MFC) (DBMFC) consisting of 18 MFC arrays was developed to enhance the robustness and stability of the power source for subsea sensor networks. A power management system (PMS) was integrated into the DBMFC system to boost the power output for two temperature sensors. The PMS was specifically designed with 18 charge pumps capable of simultaneously harvesting energy from 6 MFC units (18 anodes total) in the DBMFC system. The pilot scale DBMFC (total sediment volume: 1 m3) with continuous ocean water supply showed that the power outputs of individual MFC units were affected by the organic carbon and nitrogen contents in the sediment pore water. The MFC units with higher power output resulted in faster charging/discharging rate of the PMS supercapacitor. Manual disconnection of anodes from the PMS was conducted to simulate the anode malfunction caused by bioturbation. Fewer functional anodes (e.g. 12 out of 18 anodes were disconnected) slowed the charging/discharging rate of the PMS supercapacitor but still supported the PMS to regularly power two sensors. This scale-up DBMFC/PMS/sensor study demonstrated that multiple MFC units with multiple PMS substantially enhanced the stability and robustness of power supply to subsea sensors.

  3. CO Spectral Line Energy Distributions in Orion Sources: Templates for Extragalactic Observations

    NASA Astrophysics Data System (ADS)

    Indriolo, Nick; Bergin, Edwin A.; Goicoechea, Javier; Schilke, Peter

    2016-01-01

    Relative populations in the excited rotational levels of CO are sensitive to conditions in the interstellar medium. Emission lines originating in these levels can thus be used in constraining parameters such as density, temperature, and radiation field. The Herschel Space Observatory has enabled the observation of CO emission lines arising from the J=4 through J=48 rotational levels, many of which are detected in different sources within the Orion star-forming region. We present observations of CO emission toward Orion KL, Orion H2 Peak 1, Orion South, and the Orion Bar, all of which show distinctive CO spectral line energy distributions (SLEDs) indicating the different excitation mechanisms at work. Using the high spectral resolution HIFI observations, we decompose emission line profiles into multiple components (e.g., shock, outflow, photodissociation region, ambient cloud) in order to characterize the CO SLED associated with each component. In doing so, we generate templates for the various excitation mechanisms that can be applied toward understanding the processes occurring in unresolved star-forming regions where CO observations have been made.

  4. Distribution and sources of organic matter in sediments of the south-eastern Baltic Sea

    NASA Astrophysics Data System (ADS)

    Remeikaitė-Nikienė, Nijolė; Lujanienė, Galina; Malejevas, Vitalijus; Barisevičiūtė, Rūta; Žilius, Mindaugas; Garnaga-Budrė, Galina; Stankevičius, Algirdas

    2016-05-01

    Temporal and spatial distribution of sedimentary organic matter (SOM) as well as its sources in the south-eastern Baltic Sea were investigated. Organic matter was characterized by the organic carbon content, δ13C and δ15N signatures and C/N ratios. The sampling was performed in the coastal, offshore areas and in the Curonian Lagoon in the period from May 2012 to September 2014. The average elemental (C/N ~ 6.4) and isotopic composition (δ13C from - 29.6‰ to - 24.9‰) of SOM suggested that during most of the year it was composed of both freshwater and marine phytoplanktonic material. Elevated δ15N values (average ranging from 5.6‰ to 6.7‰) were detected in SOM from the Curonian Lagoon. This most likely reflected the increased isotopic signal of the Nemunas River (δ15N ~ 8‰) derived from the anthropogenic input in the basin area. At the Baltic Sea offshore sites, SOM had lower δ15N values (δ15N ~ 3.5‰ on average), indicating phytoplankton blooms. A two-end member mixing model based on the carbon stable isotopic composition showed that a large proportion (~ 90%) of SOM in the northern part of the Curonian Lagoon was of the freshwater origin. The allochthonous organic matter accounted for about 47% of SOM in the studied Baltic Sea area with the highest contribution (about 75%) within the Curonian Lagoon plume zone in the coastal waters.

  5. Simulated spatial distribution and seasonal variation of atmospheric methane over China: Contributions from key sources

    NASA Astrophysics Data System (ADS)

    Zhang, Dingyuan; Liao, Hong; Wang, Yuesi

    2014-03-01

    We used the global atmospheric chemical transport model, GEOS-Chem, to simulate the spatial distribution and seasonal variation of surface-layer methane (CH4) in 2004, and quantify the impacts of individual domestic sources and foreign transport on CH4 concentrations over China. Simulated surface-layer CH4 concentrations over China exhibit maximum concentrations in summer and minimum concentrations in spring. The annual mean CH4 concentrations range from 1800 ppb over western China to 2300 ppb over the more populated eastern China. Foreign emissions were found to have large impacts on CH4 concentrations over China, contributing to about 85% of the CH4 concentrations over western China and about 80% of those over eastern China. The tagged simulation results showed that coal mining, livestock, and waste are the dominant domestic contributors to CH4 concentrations over China, accounting for 36%, 18%, and 16%, respectively, of the annual and national mean increase in CH4 concentration from all domestic emissions. Emissions from rice cultivation were found to make the largest contributions to CH4 concentrations over China in the summer, which is the key factor that leads to the maximum seasonal mean CH4 concentrations in summer.

  6. Methane emission from natural wetlands: Global distribution, area, and environmental characteristics of sources

    SciTech Connect

    Matthews, E.; Fung, I. )

    1987-03-01

    A global data base of wetlands at 1 degree resolution was developed from the integration of three independent global, digital sources: (1) vegetation, (2) soil properties and (3) fractional inundation in each 1 degree cell. The integration yielded a global distribution of wetland sites identified with in situ ecological and environmental characteristics. The wetland sites were classified into five major groups on the basis of environmental characteristics governing methane emissions. The global wetland area derived in this study is 5.3 trillion sq m, approximately twice the wetland area previously used in methane emission studies. Methane emission was calculated using methane fluxes for the major wetland groups, and simple assumptions about the duration of the methane production season. The annual methane emission from wetlands is about 110 Tg, well within the range of previous estimates. Tropical/subtropical peat-poor swamps from 20 degrees N to 30 degrees S account from 30% of the global wetland area and 25% of the total methane emission. About 60% of the total emission comes from peat-rich bogs concentrated from 50-70 degrees N, suggesting that the highly seasonal emission from these ecosystems is the major contributor to the large annual oscillations observed in atmospheric methane concentrations at these latitudes. 78 refs., 6 figs., 5 tabs.

  7. Distributed Bragg reflector ring oscillators: A large aperture source of high single-mode optical power

    SciTech Connect

    Dzurko, K.M.; Hardy, A.; Scifres, D.R.; Welch, D.F.; Waarts, R.G.; Lang, R.J. )

    1993-06-01

    Distributed Bragg reflector (DBR) ring oscillators are the first monolithic semiconductor lasers containing broad-area active regions which operate in a single mode to several times their threshold current. Orthogonally oriented diffraction gratings surrounding an unpatterned active region select a single spatial and temporal mode of oscillation. This paper presents both analytic and experimental verification of single mode operation for active dimensions up to 368 [times] 1000 [mu]m. Threshold current densities under 200 A/cm[sup 2] and total differential efficiencies greater than 60% have been measured. DBR ring oscillators have demonstrated over 1 W of single frequency output power, 460 mW of spatially coherent, single frequency output power, and nearly circular diffraction limited output to 4 [times] I[sub th]. The performance potential of these devices is enormous, considering that the output apertures are nearly two orders of magnitude wider than conventional single mode sources which generate up to 0.2 W of coherent output.

  8. Size distribution, characteristics and sources of heavy metals in haze episode in Beijing.

    PubMed

    Duan, Jingchun; Tan, Jihua; Hao, Jiming; Chai, Fahe

    2014-01-01

    Size segragated samples were collected during high polluted winter haze days in 2006 in Beijing, China. Twenty nine elements and 9 water soluble ions were determined. Heavy metals of Zn, Pb, Mn, Cu, As, Cr, Ni, V and Cd were deeply studied considering their toxic effect on human being. Among these heavy metals, the levels of Mn, As and Cd exceeded the reference values of National Ambient Air Quality Standard (GB3095-2012) and guidelines of World Health Organization. By estimation, high percentage of atmospheric heavy metals in PM2.5 indicates it is an effective way to control atmospheric heavy metals by PM2.5 controlling. Pb, Cd, and Zn show mostly in accumulation mode, V, Mn and Cu exist mostly in both coarse and accumulation modes, and Ni and Cr exist in all of the three modes. Considering the health effect, the breakthrough rates of atmospheric heavy metals into pulmonary alveoli are: Pb (62.1%) > As (58.1%) > Cd (57.9%) > Zn (57.7%) > Cu (55.8%) > Ni (53.5%) > Cr (52.2%) > Mn (49.2%) > V (43.5%). Positive matrix factorization method was applied for source apportionment of studied heavy metals combined with some marker elements and ions such as K, As, SO4(2-) etc., and four factors (dust, vehicle, aged and transportation, unknown) are identified and the size distribution contribution of them to atmospheric heavy metals are discussed. PMID:24649706

  9. Propagation in 3D spiral-arm cosmic-ray source distribution models and secondary particle production using PICARD

    NASA Astrophysics Data System (ADS)

    Kissmann, R.; Werner, M.; Reimer, O.; Strong, A. W.

    2015-10-01

    We study the impact of possible spiral-arm distributions of Galactic cosmic-ray sources on the flux of various cosmic-ray nuclei throughout our Galaxy. We investigate model cosmic-ray spectra at the nominal position of the sun and at different positions within the Galaxy. The modelling is performed using the recently introduced numerical cosmic ray propagation code PICARD. Assuming non-axisymmetric cosmic-ray source distributions yields new insights on the behaviour of primary versus secondary nuclei. We find that primary cosmic rays are more strongly confined to the vicinity of the sources, while the distribution of secondary cosmic rays is much more homogeneous compared to the primaries. This leads to stronger spatial variation in secondary to primary ratios when compared to axisymmetric source distribution models. A good fit to the cosmic-ray data at Earth can be accomplished in different spiral-arm models, although leading to decisively different spatial distributions of the cosmic-ray flux. These lead to different cosmic ray anisotropies, where even reproducing the data becomes possible. Consequently, we advocate directions to seek best fit propagation parameters that take into account the higher complexity introduced by the spiral-arm structure on the cosmic-ray distribution. We specifically investigate whether the flux at Earth is representative for a large fraction of the Galaxy. The variance among possible spiral-arm models allows us to quantify the spatial variation of the cosmic-ray flux within the Galaxy in presence of non-axisymmetric source distributions.

  10. Simulations of a spectral gamma-ray logging tool response to a surface source distribution on the borehole wall

    SciTech Connect

    Wilson, R.D.; Conaway, J.G.

    1991-12-01

    We have developed Monte Carlo and discrete ordinates simulation models for the large-detector spectral gamma-ray (SGR) logging tool in use at the Nevada Test Site. Application of the simulation models produced spectra for source layers on the borehole wall, either from potassium-bearing mudcakes or from plate-out of radon daughter products. Simulations show that the shape and magnitude of gamma-ray spectra from sources distributed on the borehole wall depend on radial position with in the air-filled borehole as well as on hole diameter. No such dependence is observed for sources uniformly distributed in the formation. In addition, sources on the borehole wall produce anisotropic angular fluxes at the higher scattered energies and at the source energy. These differences in borehole effects and in angular flux are important to the process of correcting SGR logs for the presence of potassium mudcakes; they also suggest a technique for distinguishing between spectral contributions from formation sources and sources on the borehole wall. These results imply the existence of a standoff effect not present for spectra measured in air-filled boreholes from formation sources. 5 refs., 11 figs.

  11. Analysis/finite-element combined methodology on temperature distribution of a finite domain with various heat sources

    SciTech Connect

    Wu, H.W.; Shii, Sheng Hwa . Dept. of Naval Architecture and Marine Engineering)

    1994-06-01

    A new method, involving the combined use of analysis and the finite-element method, is applicable to the heat conduction problem with isolated heat sources. Unlike the finite-element method the analysis/finite-element combined method is able to discretize the distributed sources with discontinuities into course elements, and the solution is still calculated accurately. The results are compared in tables with exact solutions and other numerical data, and the agreement is found to be good.

  12. Reactive hydro- end chlorocarbons in the troposphere and lower stratosphere : sources, distributions, and chemical impact

    NASA Astrophysics Data System (ADS)

    Scheeren, H. A.

    2003-09-01

    The work presented in this thesis focuses on measurements of chemical reactive C2 C7 non-methane hydrocarbons (NMHC) and C1 C2 chlorocarbons with atmospheric lifetimes of a few hours up to about a year. The group of reactive chlorocarbons includes the most abundant atmospheric species with large natural sources, which are chloromethane (CH3Cl), dichloromethane (CH2Cl2), and trichloromethane (CHCl3), and tetrachloroethylene (C2Cl4) with mainly anthropogenic sources. The NMHC and chlorocarbons are present at relatively low quantities in our atmosphere (10-12 10-9 mol mol-1 of air). Nevertheless, they play a key role in atmospheric photochemistry. For example, the oxidation of NMHC plays a dominant role in the formation of ozone in the troposphere, while the photolysis of chlorocarbons contributes to enhanced ozone depletion in the stratosphere. In spite of their important role, however, their global source and sinks budgets are still poorly understood. Hence, this study aims at improving our understanding of the sources, distribution, and chemical role of reactive NMHC and chlorocarbons in the troposphere and lower stratosphere. To meet this aim, a comprehensive data set of selected C2 C7 NMHC and chlorocarbons has been analyzed, derived from six aircraft measurement campaigns with two different jet aircrafts (the Dutch TUD/NLR Cessna Citation PH-LAB, and the German DLR Falcon) conducted between 1995 and 2001 (STREAM 1995 and 1997 and 1998, LBA-CLAIRE 1998, INDOEX 1999, MINOS 2001). The NMHC and chlorocarbons have been detected by gas-chromatography (GC-FID/ECD) in pre-concentrated whole air samples collected in stainless steel canister on-board the measurement aircrafts. The measurement locations include tropical (Maldives/Indian Ocean and Surinam), midlatitude (Western Europe and Canada) and polar regions (Lapland/northern Sweden) between the equator to about 70ºN, covering different seasons and pollution levels in the troposphere and lower stratosphere. Of

  13. Trace element content, source and distribution regularities in groundwater of Baltic Artesian basin

    NASA Astrophysics Data System (ADS)

    Retike, I.; Kalvans, A.; Delina, A.; Babre, A.; Raga, B.; Perkone, E.; Bikse, J.

    2012-04-01

    The territory of Latvia is a part of the Baltic Artesian (Sedimentary) basin which considering water chemistry and intensity of water connection between aquifers can be divided into three major water exchange zones: freshwater (active water exchange), saline (delayed exchange), and brines (stagnant water exchange zone). An extensive data set about groundwater in Latvia is available from the beginning of the 1960s. Regular groundwater monitoring mainly contains data about groundwater levels, major ion chemistry and physical parameters. Two types of data sources are available on groundwater trace element concentrations in Latvia: 1) the data from geological mapping and hydrogeological exploration during Soviet times and 2) recent studies, particularly "Agricultural influence on groundwater in Latvia" (Gosk et al. 2006). It is impossible to test the quality of the first; therefore, the old data is incomparable to data obtained by modern methods. The second data source is mainly limited to Quaternary sedimentary aquifer susceptible to agricultural influence. Lack of available trace element data in deeper strata led to begin such a study. The aim of this study is to determine the distribution and sources of trace elements in groundwater in Latvia and compare the results with WHO and EU potable water standards. The obtained results will be compared with the major ion chemistry data and interpret together with stable isotope signals as well as tritium and CFC's data to determine surface recharge intensity thus distinguish possible trace element source. Approximately two hundred groundwater samples from monitoring and supply wells as well as boreholes, and springs will be analyzed by total x-ray fluorescence (TXRF) and atomic absorption spectroscopy (AAS) techniques to determine the concentration of trace elements. The major benefits of using TXRF analysis is a simple multi-element analysis without external calibration, low maintenance and operating costs, and a small

  14. Direct reconstruction of the source intensity distribution of a clinical linear accelerator using a maximum likelihood expectation maximization algorithm

    NASA Astrophysics Data System (ADS)

    Papaconstadopoulos, P.; Levesque, I. R.; Maglieri, R.; Seuntjens, J.

    2016-02-01

    Direct determination of the source intensity distribution of clinical linear accelerators is still a challenging problem for small field beam modeling. Current techniques most often involve special equipment and are difficult to implement in the clinic. In this work we present a maximum-likelihood expectation-maximization (MLEM) approach to the source reconstruction problem utilizing small fields and a simple experimental set-up. The MLEM algorithm iteratively ray-traces photons from the source plane to the exit plane and extracts corrections based on photon fluence profile measurements. The photon fluence profiles were determined by dose profile film measurements in air using a high density thin foil as build-up material and an appropriate point spread function (PSF). The effect of other beam parameters and scatter sources was minimized by using the smallest field size (0.5× 0.5 cm2). The source occlusion effect was reproduced by estimating the position of the collimating jaws during this process. The method was first benchmarked against simulations for a range of typical accelerator source sizes. The sources were reconstructed with an accuracy better than 0.12 mm in the full width at half maximum (FWHM) to the respective electron sources incident on the target. The estimated jaw positions agreed within 0.2 mm with the expected values. The reconstruction technique was also tested against measurements on a Varian Novalis Tx linear accelerator and compared to a previously commissioned Monte Carlo model. The reconstructed FWHM of the source agreed within 0.03 mm and 0.11 mm to the commissioned electron source in the crossplane and inplane orientations respectively. The impact of the jaw positioning, experimental and PSF uncertainties on the reconstructed source distribution was evaluated with the former presenting the dominant effect.

  15. Direct reconstruction of the source intensity distribution of a clinical linear accelerator using a maximum likelihood expectation maximization algorithm.

    PubMed

    Papaconstadopoulos, P; Levesque, I R; Maglieri, R; Seuntjens, J

    2016-02-01

    Direct determination of the source intensity distribution of clinical linear accelerators is still a challenging problem for small field beam modeling. Current techniques most often involve special equipment and are difficult to implement in the clinic. In this work we present a maximum-likelihood expectation-maximization (MLEM) approach to the source reconstruction problem utilizing small fields and a simple experimental set-up. The MLEM algorithm iteratively ray-traces photons from the source plane to the exit plane and extracts corrections based on photon fluence profile measurements. The photon fluence profiles were determined by dose profile film measurements in air using a high density thin foil as build-up material and an appropriate point spread function (PSF). The effect of other beam parameters and scatter sources was minimized by using the smallest field size ([Formula: see text] cm(2)). The source occlusion effect was reproduced by estimating the position of the collimating jaws during this process. The method was first benchmarked against simulations for a range of typical accelerator source sizes. The sources were reconstructed with an accuracy better than 0.12 mm in the full width at half maximum (FWHM) to the respective electron sources incident on the target. The estimated jaw positions agreed within 0.2 mm with the expected values. The reconstruction technique was also tested against measurements on a Varian Novalis Tx linear accelerator and compared to a previously commissioned Monte Carlo model. The reconstructed FWHM of the source agreed within 0.03 mm and 0.11 mm to the commissioned electron source in the crossplane and inplane orientations respectively. The impact of the jaw positioning, experimental and PSF uncertainties on the reconstructed source distribution was evaluated with the former presenting the dominant effect. PMID:26758232

  16. Depth to the bottom of magnetic sources (DBMS) from aeromagnetic data of Central India using modified centroid method for fractal distribution of sources

    NASA Astrophysics Data System (ADS)

    Bansal, A. R.; Anand, S. P.; Rajaram, Mita; Rao, V. K.; Dimri, V. P.

    2013-09-01

    The depth to the bottom of the magnetic sources (DBMS) has been estimated from the aeromagnetic data of Central India. The conventional centroid method of DBMS estimation assumes random uniform uncorrelated distribution of sources and to overcome this limitation a modified centroid method based on scaling distribution has been proposed. Shallower values of the DBMS are found for the south western region. The DBMS values are found as low as 22 km in the south west Deccan trap covered regions and as deep as 43 km in the Chhattisgarh Basin. In most of the places DBMS are much shallower than the Moho depth, earlier found from the seismic study and may be representing the thermal/compositional/petrological boundaries. The large variation in the DBMS indicates the complex nature of the Indian crust.

  17. Measurement of ultrafine particle size distributions from coal-, oil-, and gas-fired stationary combustion sources.

    PubMed

    Chang, M C Oliver; Chow, Judith C; Watson, John G; Hopke, Philip K; Yi, Seung-Muk; England, Glenn C

    2004-12-01

    Currently, we have limited knowledge of the physical and chemical properties of emitted primary combustion aerosols and the changes in those properties caused by nucleation, condensation growth of volatile species, and particle coagulations under dilution and cooling in the ambient air. A dilution chamber was deployed to sample exhaust from a pilot-scale furnace burning various fuels at a nominal heat input rate of 160 kW/h(-1) and 3% excess oxygen. The formation mechanisms of particles smaller than 420 nm in electrical mobility diameter were experimentally investigated by measurement with a Scanning Mobility Particle Sizer (SMPS) as a function of aging times, dilution air ratios, combustion exhaust temperatures, and fuel types. Particle formation in the dilution process is a complex mixture of nucleation, coagulation, and condensational growth, depending on the concentrations of available condensable species and solid or liquid particles (such as soot, ash) in combustion exhausts. The measured particle size distributions in number concentrations measured show peaks of particle number concentrations for medium sulfur bituminous coal, No. 6 fuel oil, and natural gas at 40-50 nm, 70-100 nm, and 15-25 nm, respectively. For No. 6 fuel oil and coal, the particle number concentration is constant in the range of a dilution air ratio of 50, but the number decreases as the dilution air ratio decreases to 10. However, for natural gas, the particle number concentration is higher at a dilution air ratio of 10 and decreases at dilution air ratios of 20-50. At a dilution air ratio of 10, severe particle coagulation occurs in a relatively short time. Samples taken at different combustion exhaust temperatures for these fuel types show higher particle number concentrations at 645 K than at 450 K. As the aging time of particles increases, the particles increase in size and the number concentrations decrease. The largest gradient of particle number distribution occurs within the

  18. Using a topographic index to distribute variable source area runoff predicted with the SCS curve-number equation

    NASA Astrophysics Data System (ADS)

    Lyon, Steve W.; Walter, M. Todd; Gérard-Marchant, Pierre; Steenhuis, Tammo S.

    2004-10-01

    Because the traditional Soil Conservation Service curve-number (SCS-CN) approach continues to be used ubiquitously in water quality models, new application methods are needed that are consistent with variable source area (VSA) hydrological processes in the landscape. We developed and tested a distributed approach for applying the traditional SCS-CN equation to watersheds where VSA hydrology is a dominant process. Predicting the location of source areas is important for watershed planning because restricting potentially polluting activities from runoff source areas is fundamental to controlling non-point-source pollution. The method presented here used the traditional SCS-CN approach to predict runoff volume and spatial extent of saturated areas and a topographic index, like that used in TOPMODEL, to distribute runoff source areas through watersheds. The resulting distributed CN-VSA method was applied to two subwatersheds of the Delaware basin in the Catskill Mountains region of New York State and one watershed in south-eastern Australia to produce runoff-probability maps. Observed saturated area locations in the watersheds agreed with the distributed CN-VSA method. Results showed good agreement with those obtained from the previously validated soil moisture routing (SMR) model. When compared with the traditional SCS-CN method, the distributed CN-VSA method predicted a similar total volume of runoff, but vastly different locations of runoff generation. Thus, the distributed CN-VSA approach provides a physically based method that is simple enough to be incorporated into water quality models, and other tools that currently use the traditional SCS-CN method, while still adhering to the principles of VSA hydrology.

  19. The statistical fluctuation analysis for the measurement-device-independent quantum key distribution with heralded single-photon sources

    NASA Astrophysics Data System (ADS)

    Zhou, Xing-Yu; Zhang, Chun-Hui; Guo, Guang-Can; Wang, Qin

    2016-06-01

    In this paper, we carry out statistical fluctuation analysis for the new proposed measurement-device-independent quantum key distribution with heralded single-photon sources and further compare its performance with the mostly often used light sources, i.e., the weak coherent source. Due to a significantly lower probability for events with two photons present on the same side of the beam splitter in former than in latter, it gives drastically reduced quantum bit error rate in the X basis and can thus show splendid behavior in real-life implementations even when taking statistical fluctuations into account.

  20. Robustness of the round-robin differential-phase-shift quantum-key-distribution protocol against source flaws

    NASA Astrophysics Data System (ADS)

    Mizutani, Akihiro; Imoto, Nobuyuki; Tamaki, Kiyoshi

    2015-12-01

    Recently, a new type of quantum key distribution, called the round-robin differential-phase-shift (RRDPS) protocol [T. Sasaki et al., Nature (London) 509, 475 (2014), 10.1038/nature13303], was proposed, where the security can be guaranteed without monitoring any statistics. In this Rapid Communication, we investigate source imperfections and side-channel attacks on the source of this protocol. We show that only three assumptions are needed for the security, and no detailed characterizations of the source or the side-channel attacks are needed. This high robustness is another striking advantage of the RRDPS protocol over other protocols.

  1. Experimental demonstration of counteracting imperfect sources in a practical one-way quantum-key-distribution system

    SciTech Connect

    Xu Fangxing; Zhang Yang; Zhou Zheng; Chen Wei; Han Zhengfu; Guo Guangcan

    2009-12-15

    In a practical quantum-key-distribution system, photon source and small operational errors cause intensity fluctuations inevitably, which cannot be ignored for a precise estimation on the single-photon fraction. In this paper, we demonstrated an efficient three-intensity decoy method scheme on top of the one-way Faraday-Michelson Interferometric system, combining an active monitoring with existing commercial apparatus to inspect fluctuations instantly. With this faithful detection for the upper bound of the fluctuation, the secure quantum key distribution is unconditionally realized with whatever type of intensity errors, which declares the utility and potential of decoy theory and active monitoring for quantum key distribution in practical use.

  2. Steady-state visual evoked potentials: distributed local sources and wave-like dynamics are sensitive to flicker frequency

    PubMed Central

    Srinivasan, Ramesh; Bibi, F. Alouani; Nunez, Paul L.

    2007-01-01

    Steady-state visual evoked potentials (SSVEPs) are used in cognitive and clinical studies of brain function because of excellent signal-to-noise ratios and relative immunity to artifacts. SSVEPs also provide a means to characterize preferred frequencies of neocortical dynamic processes. In this study, SSVEPs were recorded with 110 electrodes while subjects viewed random dot patterns flickered between 3 and 30 Hz. Peaks in SSVEP power were observed at delta (3 Hz), lower alpha (7 and 8 Hz), and upper alpha band (12 and 13 Hz) frequencies; the spatial distribution of SSVEP power is also strongly dependent on the input frequency suggesting cortical resonances. We characterized the cortical sources that generate SSVEPs at different input frequencies by applying surface Laplacians and spatial spectral analysis. Laplacian SSVEPs recorded are sensitive to small changes (1–2 Hz) in the input frequency at occipital and parietal electrodes indicating distinct local sources. At 10 Hz, local source activity occurs in multiple cortical regions; Laplacian SSVEPs are also observed in lateral frontal electrodes. Laplacian SSVEPs are negligible at many frontal electrodes that elicit strong potential SSVEPs at delta, lower alpha, and upper alpha bands. One-dimensional (anterior-posterior) spatial spectra indicate that distinct large-scale source distributions contribute SSVEP power in these frequency bands. In the upper alpha band, spatial spectra indicate the presence of long-wavelength (> 15 cm) traveling waves propagating from occipital to prefrontal electrodes. In the delta and lower alpha band, spatial spectra indicate that long-wavelength source distributions over posterior and anterior regions form standing-wave patterns. These results suggest that the SSVEP is generated by both (relatively stationary) localized sources and distributed sources that exhibit characteristics of wave phenomena. PMID:16544207

  3. Sources and Distribution of Organic Matter in Sediments of the Louisiana Continental Shelf

    EPA Science Inventory

    Both riverine and marine sources of organic matter (OM) contribute to sediment organic pools, and either source can contribute significantly to sediment accumulation, burial, and remineralization rates on river dominated continental shelf systems. For the Louisiana continental sh...

  4. Evaluation of the dose distribution for prostate implants using various {sup 125}I and {sup 103}Pd sources

    SciTech Connect

    Meigooni, Ali S.; Luerman, Christine M.; Sowards, Keith T.

    2009-04-15

    Recently, several different models of {sup 125}I and {sup 103}Pd brachytherapy sources have been introduced in order to meet the increasing demand for prostate seed implants. These sources have different internal structures; hence, their TG-43 dosimetric parameters are not the same. In this study, the effects of the dosimetric differences among the sources on their clinical applications were evaluated. The quantitative and qualitative evaluations were performed by comparisons of dose distributions and dose volume histograms of prostate implants calculated for various designs of {sup 125}I and {sup 103}Pd sources. These comparisons were made for an identical implant scheme with the same number of seeds for each source. The results were compared with the Amersham model 6711 seed for {sup 125}I and the Theragenics model 200 seed for {sup 103}Pd using the same implant scheme.

  5. MEG (Magnetoencephalography) multipolar modeling of distributed sources using RAP-MUSIC (Recursively Applied and Projected Multiple Signal Characterization)

    SciTech Connect

    Mosher, J. C.; Baillet, S.; Jerbi, K.; Leahy, R. M.

    2001-01-01

    We describe the use of truncated multipolar expansions for producing dynamic images of cortical neural activation from measurements of the magnetoencephalogram. We use a signal-subspace method to find the locations of a set of multipolar sources, each of which represents a region of activity in the cerebral cortex. Our method builds up an estimate of the sources in a recursive manner, i.e. we first search for point current dipoles, then magnetic dipoles, and finally first order multipoles. The dynamic behavior of these sources is then computed using a linear fit to the spatiotemporal data. The final step in the procedure is to map each of the multipolar sources into an equivalent distributed source on the cortical surface. The method is illustrated through an application to epileptic interictal MEG data.

  6. Distribution and sources of organic matter in surface marine sediments across the North American Arctic margin

    NASA Astrophysics Data System (ADS)

    Goñi, Miguel A.; O'Connor, Alison E.; Kuzyk, Zou Zou; Yunker, Mark B.; Gobeil, Charles; Macdonald, Robie W.

    2013-09-01

    As part of the International Polar Year research program, we conducted a survey of surface marine sediments from box cores along a section extending from the Bering Sea to Davis Strait via the Canadian Archipelago. We used bulk elemental and isotopic compositions, together with biomarkers and principal components analysis, to elucidate the distribution of marine and terrestrial organic matter in different regions of the North American Arctic margin. Marked regional contrasts were observed in organic carbon loadings, with the highest values (≥1 mg C m-2 sediment) found in sites along Barrow Canyon and the Chukchi and Bering shelves, all of which were characterized by sediments with low oxygen exposure, as inferred from thin layers (<2 cm) of Mn oxihydroxides. We found strong regional differences in inorganic carbon concentrations, with sites from the Canadian Archipelago and Lancaster Sound displaying elevated values (2-7 wt %) and highly depleted 14C compositions consistent with inputs from bedrock carbonates. Organic carbon:nitrogen ratios, stable carbon isotopes, and terrigenous organic biomarkers (lignin phenols and cutin acids) all indicate marked regional differences in the proportions of marine and terrigenous organic matter present in surface sediments. Regions such as Barrow Canyon and the Mackenzie River shelf were characterized by the highest contributions of land-derived organic matter, with compositional characteristics that suggested distinct sources and provenance. In contrast, sediments from the Canadian Archipelago and Davis Strait had the smallest contributions of terrigenous organic matter and the lowest organic carbon loadings indicative of a high degree of post-depositional oxidation.

  7. [Size distribution of particle and polycyclic aromatic hydrocarbons in particle emissions from simulated emission sources].

    PubMed

    Fu, Hai-Huan; Tian, Na; Shang, Hui-Bin; Zhang, Bin; Ye, Su-Fen; Chen, Xiao-Qiu; Wu, Shui-Ping

    2014-01-01

    Particles from cooking lampblack, biomass and plastics burning smoke, gasoline vehicular exhausts and gasoline generator exhausts were prepared in a resuspension test chamber and collected using a cascade MOUDI impactor. A total of 18 polycyclic aromatic hydrocarbons (PAHs) associated with particles were analyzed by GC-MS. The results showed that there were two peaks in the range of 0.44-1.0 microm and 2.5-10 microm for cooking lampblack, and only one peak in the range of 0.44-1.0 microm for straw and wood burning smoke. But there were no clear peak for plastics burning smoke. The peak for gasoline vehicular exhausts was found in the range of 2.5-10 microm due to the influence of water vapor associated with particles, while the particles from gasoline generator exhausts were mainly in the range of < or = 2.5 microm (accounting for 93% of the total mass). The peak in 2.5-10 microm was clear for cooking lampblack and gasoline vehicular exhausts. The peak in the range of 0.44-1.0 microm became more and more apparent with the increase of PAHs molecular weight. The fraction of PAH on particles less than 1.0 microm to that on the total particles increased along with PAH's molecular weight. Phenanthrene was the dominant compound for cooking lampblack and combustion smoke, while gasoline vehicular exhausts and generator exhausts were characterized with significantly high levels of naphthalene and benzo[g, h, i] perylene, respectively. The distribution of source characteristic ratios indicated that PAHs from cooking lampblack and biomass burning were close and they were different from those of vehicular exhausts and generator exhausts. PMID:24720184

  8. Occurrence, distribution, and sources of antimicrobials in a mixed-use watershed.

    PubMed

    Couperus, Nathanael P; Pagsuyoin, Sheree A; Bragg, Leslie M; Servos, Mark R

    2016-01-15

    The release into the environment of antimicrobial compounds from both human and agricultural sources is a growing global concern. The Grand River watershed, the largest mixed-use watershed in southern Ontario, receives runoff from intensive animal production as well as municipal wastewater effluents from a rapidly increasing human population. A survey of surface waters and wastewater effluents was conducted across the watershed to assess the occurrence and distribution of several antimicrobials (i.e., trimethoprim, sulfamethoxazole, sulfamethazine, lincomycin, and monensin) and chemical indicators (i.e., ammonia, nitrate, ibuprofen, venlafaxine, atrazine) and to characterize exposure levels. The human antimicrobials trimethoprim and sulfamethoxazole were detected in the urban areas of the main channel at mean concentrations of 8 ± 7 ng/L and 31 ± 24 ng/L, respectively, but at much lower concentrations in the agricultural tributaries. In contrast, the veterinary antimicrobial sulfamethazine was detected at a mean concentration of 11 ± 9 ng/L in the main channel, and at a much higher concentration in the agricultural tributaries. Lincomycin was detected in only two river samples and not in the effluents while monensin was not detected in all samples. The herbicide atrazine was detected at very low concentrations in the surface waters of both the tributaries and the main channel. The concentrations of the antimicrobials and chemical indicators generally increased downstream of the confluences with agricultural tributaries and effluent outfalls. In the wastewater effluents, the concentrations of trimethoprim, sulfamethoxazole, ibuprofen, and venlafaxine decreased with increasing treatment levels (i.e., secondary to tertiary) as indicated by ammonia/nitrate concentrations. There was a strong correlation among trimethoprim, sulfamethoxazole, and venlafaxine in the main channel and in the wastewater effluents. While the environmental concentrations of antimicrobials in

  9. Polybromobenzene pollutants in the atmosphere of North China: levels, distribution, and sources.

    PubMed

    Lin, Yan; Qiu, Xinghua; Zhao, Yifan; Ma, Jin; Yang, Qiaoyun; Zhu, Tong

    2013-11-19

    Brominated flame retardants (BFRs) are important persistent organic pollutants. Analysis of BFRs in atmospheric samples in a previous study led us to suspect the presence of unidentified organic bromides, other than polybrominated diphenyl ethers (PBDEs), in the atmosphere. In this study, we identified and quantified polybromobenzenes, a group of organic bromides, in air samples collected through passive sampling in gridded observations in North China. We investigated their concentrations and spatial distribution, and estimated the proportion due to different sources. We detected seven species of polybromobenzenes, including hexabromobenzene (HBB), pentabromotoluene (PBT), pentabromoethylbenzene (PBEB), pentabromobenzene (PeBB), tetrabromobenzenes (TeBBs), and tribromotoluene (TrBT), in all or most of the field samples, indicating widespread occurrence of this class of pollutants. The median concentrations of each pollutant ranged from 20.0 to 144 pg/sample (or from 0.07 to 1.16 pg/m(3)), with relatively high concentrations found near e-waste recycling sites, BFR manufacturing sites, and areas of high population density. Positive matrix factorization (PMF) analysis revealed that ∼70% of HBB, PBT, PBEB, and PeBB was from commercial products, while ∼80% of 1,2,3,5-TeBB, 1,2,4,5-TeBB, and 2,4,5-TrBT was linked with BFR manufacturing. This study provides essential information on widespread polybromobenzene pollutants in the atmosphere, particularly TeBBs and TrBT, for which this is the first report of their presence as atmospheric pollutants. PMID:24144297

  10. Estimation of Basal Depth of Magnetic Sources from High Resolution Aeromagnetic Data of Middle Niger Basin, Nigeria using Adapted Centroid Technique for Fractal Distribution of Sources

    NASA Astrophysics Data System (ADS)

    Nwankwo, L.

    2015-12-01

    An estimate of depths to the bottom of magnetic sources in the Middle Niger Basin, north-central Nigeria has been made from a recently acquired high-resolution aeromagnetic data using adapted centroid technique for fractal distribution of sources. The result shows that the depth varies between 11.71 and 26.53 km. Deeper values are found in northern and central regions while values as low as 12 km were observed in the southern part. The shallower depths to the bottom of magnetic sources may be representing the thermal/petrological boundaries in the basin. This study is therefore crucial for quantitative understanding of the geo-processes and geothermal parameters in the study area.

  11. Managing Uncertainty Due to a Fundamental Error Source Arising from Scatterer Distribution Complexity in Radar Remote Sensing of Precipitation

    NASA Technical Reports Server (NTRS)

    Smith, Eric A.; Kuo, Kwo-Sen; Meneghini, Robert; Mugnai, Alberto

    2007-01-01

    The assumption that cloud and rain drops are spatially distributed according to a Poisson distribution within a scattering volume probed by a radar being used to estimate precipitation has represented bedrock theory in establishing 'rules of the game' for pulse averaging--the process needed to beat down noise to an acceptable level in the measurement of radar reflectivity factor. Based on relatively recent observations of 'realistic' spatial distributions of hydrometeor scatterers in a cloudy atmosphere motivates a renewed examination of the consequences of using a too simplified assumption underlying volume scattering--particularly in regards to the standard pulse averaging rule. Our investigation addresses two extremes, simple to complex, insofar as allowed for complexities in an underlying scatterer distribution. It is demonstrated that as the spatial distribution ranges from Poisson (a narrow distribution) to multi-fractal (much broader distribution), uncertainty in a measurement increases if the rule for pulse averaging goes unchanged from its Poisson distribution reference county. [A bounded cascade is used for the multi-fractal distribution, a regularly observed distribution vis-a-vis cloud liquid water content.] The resultant measurement uncertainty leads to a fundamental source of error in the estimation of rain rate from radar measurements, one that has been disregarded since the early 1950s when radar sets first began to be used for rainfall measuring. It is shown how this source of error can be 'managed'--under the assumption that number of data analysis experiments would be carried out, experiments involving pulse-by-pulse measurements obtained from a radar set modified to output individual pulses of reflectivity factor. For practical applications, a new parameter called normalized k-sample intensity invariance is developed to enable defining the required pulse average count according to a preferred degree of uncertainty.

  12. The Relation between School Leadership from a Distributed Perspective and Teachers' Organizational Commitment: Examining the Source of the Leadership Function

    ERIC Educational Resources Information Center

    Hulpia, Hester; Devos, Geert; Van Keer, Hilde

    2011-01-01

    Purpose: In this study the relationship between school leadership and teachers' organizational commitment is examined by taking into account a distributed leadership perspective. The relation between teachers' organizational commitment and contextual variables of teachers' perceptions of the quality and the source of the supportive and supervisory…

  13. moocRP: Enabling Open Learning Analytics with an Open Source Platform for Data Distribution, Analysis, and Visualization

    ERIC Educational Resources Information Center

    Pardos, Zachary A.; Whyte, Anthony; Kao, Kevin

    2016-01-01

    In this paper, we address issues of transparency, modularity, and privacy with the introduction of an open source, web-based data repository and analysis tool tailored to the Massive Open Online Course community. The tool integrates data request/authorization and distribution workflow features as well as provides a simple analytics module upload…

  14. 75 FR 70618 - Distribution of Source Material to Exempt Persons and to General Licensees and Revision of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-18

    ...On July 26, 2010, the U. S. Nuclear Regulatory Commission (NRC or the Commission) published for public comment a proposed rule to amend its regulations to require that the initial distribution of source material to exempt persons or general licensees be explicitly authorized by a specific license. The proposed rule would also modify the existing possession and use requirements of the general......

  15. 78 FR 33691 - Distribution of Source Material to Exempt Persons and to General Licensees and Revision of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-05

    ...: Discussion The NRC's Distribution of Source Material Rule (78 FR 32310; May 29, 2013) amended the NRC's..., 2011, the NRC published the draft ] interim staff guidance in the Federal Register (76 FR 1100) for... ID NRC-2009-0084. Address questions about NRC dockets to Carol Gallagher; telephone:...

  16. Source apportionment of ambient fine particle from combined size distribution and chemical composition data during summertime in Beijing

    NASA Astrophysics Data System (ADS)

    Liu, Z. R.; Wang, Y. S.; Liu, Q.; Hu, B.; Sun, Y.

    2013-01-01

    Continuous particle number concentration and chemical composition data were collected over one month during summertime in Beijing to investigate the source apportionment of ambient fine particles. Particle size distributions from 15 nm to 2.5 μm in diameter and composition data, such as organic matter, sulfate, nitrate, ammonium, chlorine, and gaseous pollutants, were analyzed using positive matrix factorisation (PMF) which indentified eight factors: cooking, solid mode exhaust, nucleation mode exhaust, accumulation mode, secondary nitrate, secondary sulfate, coal-fired power plant and road dust. Nearly two-thirds of particle number concentrations were attributed to cooking (22.8%) and motor vehicle (37.5%), whereas road dust, coal-fired power plant and regional sources contributed 69.0% to particle volume concentrations. Local and remote sources were distinguished using size distributions associated with each factor. Local sources were generally characterised by unimodal or bimodal number distributions, consisting mostly of particles less 0.1 μm in diameter, and regional sources were defined by mostly accumulation mode particles. Nearly one third of secondary nitrate and secondary sulfate was transported from the surrounding areas of Beijing during study period. Overall the introduction of combination of particle number concentration and chemical composition in PMF model is successful at separating the components and quantifying relative contributions to the particle number and volume population in a complex urban atmosphere.

  17. Urban dust in the Guanzhong Basin of China, part I: A regional distribution of dust sources retrieved using satellite data.

    PubMed

    Long, Xin; Li, Nan; Tie, Xuexi; Cao, Junji; Zhao, Shuyu; Huang, Rujin; Zhao, Mudan; Li, Guohui; Feng, Tian

    2016-01-15

    Urban dust pollution has been becoming an outstanding environmental problem due to rapid urbanization in China. However, it is very difficult to construct an urban dust inventory, owing to its small horizontal scale and strong temporal/spatial variability. With the analysis of visual interpretation, maximum likelihood classification, extrapolation and spatial overlaying, we quantified dust source distributions of urban constructions, barrens and croplands in the Guanzhong Basin using various satellite data, including VHR (0.5m), Lansat-8 OLI (30 m) and MCD12Q1 (500 m). The croplands were the dominant dust sources, accounting for 40% (17,913 km(2)) of the study area in summer and 36% (17,913 km(2)) in winter, followed by barrens, accounting for 5% in summer and 10% in winter. Moreover, the total constructions were 126 km(2), including 84% of active and 16% inactive. In addition, 59% of the constructions aggregated on the only megacity of the study area, Xi'an. With high accuracy exceeding 88%, the proposed satellite-data based method is feasible and valuable to quantify distributions of dust sources. This study provides a new perspective to evaluate regional urban dust, which is seldom quantified and reported. In a companied paper (Part-2 of the study), the detailed distribution of the urban dust sources is applied in a dynamical/aerosol model (WRF-Dust) to assess the effect of dust sources on aerosol pollution. PMID:26518756

  18. Experimental Investigation and 3D Finite Element Prediction of Temperature Distribution during Travelling Heat Sourced from Oxyacetylene Flame

    NASA Astrophysics Data System (ADS)

    Umar Alkali, Adam; Lenggo Ginta, Turnad; Majdi Abdul-Rani, Ahmad

    2015-04-01

    This paper presents a 3D transient finite element modelling of the workpiece temperature field produced during the travelling heat sourced from oxyacetylene flame. The proposed model was given in terms of preheat-only test applicable during thermally enhanced machining using the oxyacetylene flame as a heat source. The FEA model as well as the experimental test investigated the surface temperature distribution on 316L stainless steel at scanning speed of 100mm/min, 125mm/min 160mm/min, 200mm/min and 250mm/min. The parametric properties of the heat source maintained constant are; lead distance Ld =10mm, focus height Fh=7.5mm, oxygen gas pressure Poxy=15psi and acetylene gas pressure Pacty=25psi. An experimental validation of the temperature field induced on type 316L stainless steel reveal that temperature distribution increases when the travelling speed decreases.

  19. Herschel-ATLAS: Dust Temperature and Redshift Distribution of SPIRE and PACS Detected Sources Using Submillimetre Colours

    NASA Technical Reports Server (NTRS)

    Amblard, A.; Cooray, Asantha; Serra, P.; Temi, P.; Barton, E.; Negrello, M.; Auld, R.; Baes, M.; Baldry, I. K.; Bamford, S.; Blain, A.; Bock, J.; Bonfield, D.; Burgarella, D.; Buttiglione, S.; Cameron, E.; Cava, A.; Clements, D.; Croom, S.; Dariush, A.; deZotti, G.; Driver, S.; Dunlop, J.; Dunne, L.; Dye, S.

    2010-01-01

    We present colour-colour diagrams of detected sources in the Herschel-ATLAS Science Demonstration Field from 100 to 500/microns using both PACS and SPIRE. We fit isothermal modified-blackbody spectral energy distribution (SED) models in order to extract the dust temperature of sources with counterparts in GAMA or SDSS with either a spectroscopic or a photometric redshift. For a subsample of 331 sources detected in at least three FIR bands with significance greater than 30 sigma, we find an average dust temperature of (28 plus or minus 8)K. For sources with no known redshifts, we populate the colour-colour diagram with a large number of SEDs generated with a broad range of dust temperatures and emissivity parameters and compare to colours of observed sources to establish the redshift distribution of those samples. For another subsample of 1686 sources with fluxes above 35 mJy at 350 microns and detected at 250 and 500 microns with a significance greater than 3sigma, we find an average redshift of 2.2 plus or minus 0.6.

  20. Size distributions and sources of elements in particulate matter at curbside, urban and rural sites in Beijing.

    PubMed

    Duan, Jingchun; Tan, Jihua; Wang, Shulan; Hao, Jimin; Chai, Fahe

    2012-01-01

    Size distributions of 29 elements in aerosols collected at urban, rural and curbside sites in Beijing were studied. High levels of Mn, Ni, As, Cd and Pb indicate the pollution of toxic heavy metals cannot be neglected in Beijing. Principal component analysis (PCA) indicates 4 sources of combustion emission, crust related sources, traffic related sources and volatile species from coal combustion. The elements can be roughly divided into 3 groups by size distribution and enrichment factors method (EFs). Group 1 elements are crust related and mainly found within coarse mode including Al, Mg, Ca, Sc, Ti, Fe, Sr, Zr and Ba; Group 2 elements are fossil fuel related and mostly concentrated in accumulation mode including S, As, Se, Ag, Cd, Tl and Pb; Group 3 elements are multi-source related and show multi-mode distribution including Be, Na, K, Cr, Mn, Co, Ni, Cu, Zn, Ga, Mo, Sn and Sb. The EFs of Be, S, Cr, Co, Ni, Cu, Ga, Se, Mo, Ag, Cd, Sb, Tl and Pb show higher values in winter than in summer indicating sources of coal combustion for heating in winter. The abundance of Cu and Sb in coarse mode is about 2-6 times higher at curbside site than at urban site indicating their traffic sources. Coal burning may be the major source of Pb in Beijing since the phase out of leaded gasoline, as the EFs of Pb are comparable at both urban and curbside sites, and about two times higher in winter than that in summer. PMID:22783618

  1. Raw materials exploitation in Prehistory of Georgia: sourcing, processing and distribution

    NASA Astrophysics Data System (ADS)

    Tushabramishvili, Nikoloz; Oqrostsvaridze, Avthandil

    2016-04-01

    Study of raw materials has a big importance to understand the ecology, cognition, behavior, technology, culture of the Paleolithic human populations. Unfortunately, explorations of the sourcing, processing and distribution of stone raw materials had a less attention until the present days. The reasons of that were: incomplete knowledge of the archaeologists who are doing the late period archaeology (Bronze Age-Medieval) and who are little bit far from the Paleolithic technology and typology; Ignorance of the stone artifacts made on different kind of raw-materials, except flint and obsidians. Studies on the origin of the stone raw materials are becoming increasingly important since in our days. Interesting picture and situation have been detected on the different sites and in different regions of Georgia. In earlier stages of Middle Paleolithic of Djruchula Basin caves the number of basalt, andesite, argillite etc. raw materials are quite big. Since 130 000 a percent of the flint raw-material is increasing dramatically. Flint is an almost lonely dominated raw-material in Western Georgia during thousand years. Since approximately 50 000 ago the first obsidians brought from the South Georgia, appeared in Western Georgia. Similar situation has been detected by us in Eastern Georgia during our excavations of Ziari and Pkhoveli open-air sites. The early Lower Paleolithic layers are extremely rich by limestone artifacts while the flint raw-materials are dominated in the Middle Paleolithic layers. Study of these issues is possible to achieve across chronologies, the origins of the sources of raw-materials, the sites and regions. By merging archaeology with anthropology, geology and geography we are able to acquire outstanding insights about those populations. New approach to the Paleolithic stone materials, newly found Paleolithic quarries gave us an opportunities to try to achieve some results for understanding of the behavior of Paleolithic populations, geology and

  2. Escherichia coli at Ohio Bathing Beaches--Distribution, Sources, Wastewater Indicators, and Predictive Modeling

    USGS Publications Warehouse

    Francy, Donna S.; Gifford, Amie M.; Darner, Robert A.

    2003-01-01

    Results of studies during the recreational seasons of 2000 and 2001 strengthen the science that supports monitoring of our Nation?s beaches. Water and sediment samples were collected and analyzed for concentrations of Escherichia coli (E. coli). Ancillary water-quality and environmental data were collected or compiled to determine their relation to E. coli concentrations. Data were collected at three Lake Erie urban beaches (Edgewater, Villa Angela, and Huntington), two Lake Erie beaches in a less populated area (Mentor Headlands and Fairport Harbor), and one inland-lake beach (Mosquito Lake). The distribution of E. coli in water and sediments within the bathing area, outside the bathing area, and near the swash zone was investigated at the three Lake Erie urban beaches and at Mosquito Lake. (The swash zone is the zone that is alternately covered and exposed by waves.) Lake-bottom sediments from outside the bathing area were not significant deposition areas for E. coli. In contrast, interstitial water and subsurface sediments from near the swash zone were enriched with E. coli. For example, E. coli concentrations were as high as 100,000 colonies per 100 milliliters in some interstitial waters. Although there are no standards for E. coli in swash-zone materials, the high concentrations found at some locations warrant concern for public health. Studies were done at Mosquito Lake to identify sources of fecal contamination to the lake and bathing beach. Escherichia coli concentrations decreased with distance from a suspected source of fecal contamination that is north of the beach but increased at the bathing beach. This evidence indicated that elevated E. coli concentrations at the bathing beach are of local origin rather than from transport of bacteria from sites to the north. Samples collected from the three Lake Erie urban beaches and Mosquito Lake were analyzed to determine whether wastewater indicators could be used as surrogates for E. coli at bathing beaches

  3. Multi-source analysis reveals latitudinal and altitudinal shifts in range of Ixodes ricinus at its northern distribution limit

    PubMed Central

    2011-01-01

    Background There is increasing evidence for a latitudinal and altitudinal shift in the distribution range of Ixodes ricinus. The reported incidence of tick-borne disease in humans is on the rise in many European countries and has raised political concern and attracted media attention. It is disputed which factors are responsible for these trends, though many ascribe shifts in distribution range to climate changes. Any possible climate effect would be most easily noticeable close to the tick's geographical distribution limits. In Norway- being the northern limit of this species in Europe- no documentation of changes in range has been published. The objectives of this study were to describe the distribution of I. ricinus in Norway and to evaluate if any range shifts have occurred relative to historical descriptions. Methods Multiple data sources - such as tick-sighting reports from veterinarians, hunters, and the general public - and surveillance of human and animal tick-borne diseases were compared to describe the present distribution of I. ricinus in Norway. Correlation between data sources and visual comparison of maps revealed spatial consistency. In order to identify the main spatial pattern of tick abundance, a principal component analysis (PCA) was used to obtain a weighted mean of four data sources. The weighted mean explained 67% of the variation of the data sources covering Norway's 430 municipalities and was used to depict the present distribution of I. ricinus. To evaluate if any geographical range shift has occurred in recent decades, the present distribution was compared to historical data from 1943 and 1983. Results Tick-borne disease and/or observations of I. ricinus was reported in municipalities up to an altitude of 583 metres above sea level (MASL) and is now present in coastal municipalities north to approximately 69°N. Conclusion I. ricinus is currently found further north and at higher altitudes than described in historical records. The

  4. Precipitation Recycling and the Vertical Distribution of Local and Remote Sources of Water for Precipitation

    NASA Technical Reports Server (NTRS)

    Bosilovich, Michael G.; Atlas, Robert (Technical Monitor)

    2002-01-01

    Precipitation recycling is defined as the amount of water that evaporates from a region that precipitates within the same region. This is also interpreted as the local source of water for precipitation. In this study, the local and remote sources of water for precipitation have been diagnosed through the use of passive constituent tracers that represent regional evaporative sources along with their transport and precipitation. We will discuss the differences between this method and the simpler bulk diagnostic approach to precipitation recycling. A summer seasonal simulation has been analyzed for the regional sources of the United States Great Plains precipitation. While the tropical Atlantic Ocean (including the Gulf of Mexico) and the local continental sources of precipitation are most dominant, the vertically integrated column of water contains substantial water content originating from the Northern Pacific Ocean, which is not precipitated. The vertical profiles of regional water sources indicate that local Great Plains source of water dominates the lower troposphere, predominantly in the PBL. However, the Pacific Ocean source is dominant over a large portion of the middle to upper troposphere. The influence of the tropical Atlantic Ocean is reasonably uniform throughout the column. While the results are not unexpected given the formulation of the model's convective parameterization, the analysis provides a quantitative assessment of the impact of local evaporation on the occurrence of convective precipitation in the GCM. Further, these results suggest that local source of water is not well mixed throughout the vertical column.

  5. Helical jets and the misalignment distribution for core-dominated radio sources

    NASA Technical Reports Server (NTRS)

    Conway, J. E.; Murphy, D. W.

    1993-01-01

    The type of a model which would explain the large population of orthogonally misaligned sources is considered. Two of the best examples of misaligned sources are investigated, namely, the quasar 3C 309.1 (Wilkinson et al., 1986; Kus et al., 1990, 1991) and the BL Lac object 1823 + 568 (Foley, 1982; O'Dea et al., 1988). It is shown that simple bend geometries cannot explain the misaligned sources, and the geometries required to give orthogonal misalignments are explained. A generally applicable model which might explain misaligned sources is proposed.

  6. Distributions, Sources and Sinks of biogenic volatile organic compounds in the Southeast U.S. (Invited)

    NASA Astrophysics Data System (ADS)

    Guenther, A. B.; Jiang, X.; Kaser, L.; Apel, E. C.; Emmons, L. K.; Fang, W.; Harley, P. C.; Hills, A. J.; Hornbrook, R. S.; Patton, E. G.; Turnipseed, A. A.; Karl, T.; Su, L.; Mak, J. E.; Misztal, P. K.; Goldstein, A. H.; Graus, M.; Warneke, C.; Yuan, B.; De Gouw, J. A.; Park, J.; Helmig, D.

    2013-12-01

    The emission of biogenic volatile organic compounds (BVOC) from terrestrial ecosystems into the atmosphere has been investigated by numerous studies in the past several decades. BVOC emissions are now widely believed to have an important role in determining atmospheric constituents including the oxidants and aerosols that control air quality and climate. Model sensitivity studies indicate that more accurate descriptions of BVOC sources and sinks are needed to understand and quantify the processes controlling air quality and climate. Evaluation and improvement of BVOC representations in regional and global models has been limited by the lack of datasets characterizing fluxes and concentrations across the scales relevant for the processes controlling BVOC emission and fate. Comprehensive BVOC measurements during the Southeast Atmosphere Study (SAS) provide a unique resource for evaluating and improving our understanding of BVOC emissions and their atmospheric impact. These observations include BVOC fluxes from individual leaves and branches measured using enclosure systems, from a whole canopy measured with an above canopy tower platform, and from entire landscapes measured by airborne eddy covariance. BVOC measurements on the NOAA P3, NCAR C130, and Stonybrook Long-EZ together provide a detailed description of horizontal and vertical BVOC variations throughout the diurnal cycle. In addition, BVOC and their oxidation products were measured with multiple techniques at the SOAS Centreville site along with a comprehensive suite of measurements including aerosols, oxidants and other atmospheric constituents. These chemical measurements were complemented with detailed observations of boundary layer structure and turbulence. This presentation will summarize the SAS BVOC observations and ancillary measurements and describe the integration of these data into a model testbed for evaluating BVOC emissions, transport and chemistry. The performance of two BVOC emission models

  7. Microfabricated AC impedance sensor

    DOEpatents

    Krulevitch, Peter; Ackler, Harold D.; Becker, Frederick; Boser, Bernhard E.; Eldredge, Adam B.; Fuller, Christopher K.; Gascoyne, Peter R. C.; Hamilton, Julie K.; Swierkowski, Stefan P.; Wang, Xiao-Bo

    2002-01-01

    A microfabricated instrument for detecting and identifying cells and other particles based on alternating current (AC) impedance measurements. The microfabricated AC impedance sensor includes two critical elements: 1) a microfluidic chip, preferably of glass substrates, having at least one microchannel therein and with electrodes patterned on both substrates, and 2) electrical circuits that connect to the electrodes on the microfluidic chip and detect signals associated with particles traveling down the microchannels. These circuits enable multiple AC impedance measurements of individual particles at high throughput rates with sufficient resolution to identify different particle and cell types as appropriate for environmental detection and clinical diagnostic applications.

  8. The effect of the charge exchange source on the velocity and 'temperature' distributions and their anisotropies in the earth's exosphere

    NASA Astrophysics Data System (ADS)

    Hodges, R. R., Jr.; Rohrbaugh, R. P.; Tinsley, B. A.

    1981-08-01

    The velocity distribution of atomic hydrogen in the earth's exosphere is calculated as a function of altitude and direction taking into account both the classic exobase source and the higher-altitude plasmaspheric charge exchange source. Calculations are performed on the basis of a Monte Carlo technique in which random ballistic trajectories of individual atoms are traced through a three-dimensional grid of audit zones, at which relative concentrations and momentum or energy fluxes are obtained. In the case of the classical exobase source alone, the slope of the velocity distribution is constant only for the upward radial velocity component and increases dramatically with altitude for the incoming radial and transverse velocity components, resulting in a temperature decrease. The charge exchange source, which produces the satellite hydrogen component and the hot ballistic and escape components of the exosphere, is found to enhance the wings of the velocity distributions, however this effect is not sufficient to overcome the temperature decreases at altitudes above one earth radius. The resulting global model of the hydrogen exosphere may be used as a realistic basis for radiative transfer calculations.

  9. Simultaneous reconstruction of emission activity and attenuation coefficient distribution from TOF data, acquired with external transmission source

    NASA Astrophysics Data System (ADS)

    Panin, V. Y.; Aykac, M.; Casey, M. E.

    2013-06-01

    The simultaneous PET data reconstruction of emission activity and attenuation coefficient distribution is presented, where the attenuation image is constrained by exploiting an external transmission source. Data are acquired in time-of-flight (TOF) mode, allowing in principle for separation of emission and transmission data. Nevertheless, here all data are reconstructed at once, eliminating the need to trace the position of the transmission source in sinogram space. Contamination of emission data by the transmission source and vice versa is naturally modeled. Attenuated emission activity data also provide additional information about object attenuation coefficient values. The algorithm alternates between attenuation and emission activity image updates. We also proposed a method of estimation of spatial scatter distribution from the transmission source by incorporating knowledge about the expected range of attenuation map values. The reconstruction of experimental data from the Siemens mCT scanner suggests that simultaneous reconstruction improves attenuation map image quality, as compared to when data are separated. In the presented example, the attenuation map image noise was reduced and non-uniformity artifacts that occurred due to scatter estimation were suppressed. On the other hand, the use of transmission data stabilizes attenuation coefficient distribution reconstruction from TOF emission data alone. The example of improving emission images by refining a CT-based patient attenuation map is presented, revealing potential benefits of simultaneous CT and PET data reconstruction.

  10. The effect of the charge exchange source on the velocity and 'temperature' distributions and their anisotropies in the earth's exosphere

    NASA Technical Reports Server (NTRS)

    Hodges, R. R., Jr.; Rohrbaugh, R. P.; Tinsley, B. A.

    1981-01-01

    The velocity distribution of atomic hydrogen in the earth's exosphere is calculated as a function of altitude and direction taking into account both the classic exobase source and the higher-altitude plasmaspheric charge exchange source. Calculations are performed on the basis of a Monte Carlo technique in which random ballistic trajectories of individual atoms are traced through a three-dimensional grid of audit zones, at which relative concentrations and momentum or energy fluxes are obtained. In the case of the classical exobase source alone, the slope of the velocity distribution is constant only for the upward radial velocity component and increases dramatically with altitude for the incoming radial and transverse velocity components, resulting in a temperature decrease. The charge exchange source, which produces the satellite hydrogen component and the hot ballistic and escape components of the exosphere, is found to enhance the wings of the velocity distributions, however this effect is not sufficient to overcome the temperature decreases at altitudes above one earth radius. The resulting global model of the hydrogen exosphere may be used as a realistic basis for radiative transfer calculations.

  11. Simultaneous reconstruction of emission activity and attenuation coefficient distribution from TOF data, acquired with external transmission source.

    PubMed

    Panin, V Y; Aykac, M; Casey, M E

    2013-06-01

    The simultaneous PET data reconstruction of emission activity and attenuation coefficient distribution is presented, where the attenuation image is constrained by exploiting an external transmission source. Data are acquired in time-of-flight (TOF) mode, allowing in principle for separation of emission and transmission data. Nevertheless, here all data are reconstructed at once, eliminating the need to trace the position of the transmission source in sinogram space. Contamination of emission data by the transmission source and vice versa is naturally modeled. Attenuated emission activity data also provide additional information about object attenuation coefficient values. The algorithm alternates between attenuation and emission activity image updates. We also proposed a method of estimation of spatial scatter distribution from the transmission source by incorporating knowledge about the expected range of attenuation map values. The reconstruction of experimental data from the Siemens mCT scanner suggests that simultaneous reconstruction improves attenuation map image quality, as compared to when data are separated. In the presented example, the attenuation map image noise was reduced and non-uniformity artifacts that occurred due to scatter estimation were suppressed. On the other hand, the use of transmission data stabilizes attenuation coefficient distribution reconstruction from TOF emission data alone. The example of improving emission images by refining a CT-based patient attenuation map is presented, revealing potential benefits of simultaneous CT and PET data reconstruction. PMID:23648397

  12. Controls on the distribution of Cretaceous source rocks in South America

    SciTech Connect

    Vear, A. )

    1993-02-01

    More than thirty South American basins, exhibiting a variety of structural styles, contain petroleum source rocks of Cretaceous age. However, the presence of truly [open quote]world-class[close quote] source rocks, capable of supplying multi-billion barrel oil provinces, is restricted to relatively few basins and appears to be primarily a function of large scale Cretaceous tectonic setting. In Early Cretaceous times the best source rocks were preserved in both a southern ocean and in the rift between South America and Africa. By the Late Cretaceous, these southern and eastern continental limits had become narrow passive margins. In contrast, on the northern continental margin a wide shelf to a restricted tropical sea was developing at this time. Periodic upwelling enhanced surface productivity on this shelf, which led to development of some of the world's richest source rocks. On the tectonically active western margin moderate quality source rocks were forming in a series of back-arc basins, whilst further west, in the Pacific fore-arc, organic-rich intervals were rarely deposited. This article documents what is known about each of the explored basins (including the volume and character of discovered petroleums), it investigates the geologic factors which governed the richness and quality of petroleum source rocks and it assesses how continued tectonic activity has modified or even destroyed primary source quality. Finally it predicts which of the as yet underexplored basins should contain good quality source rocks and could become prolific petroleum provinces of the future.

  13. Dose distribution along the transverse axis of a new 125I source for interstitial brachytherapy.

    PubMed

    Nath, R; Yue, N

    2000-11-01

    A new encapsulated source of 125I has been introduced for interstitial brachytherapy. This source, isoSTAR model 12501 (manufactured by Imagyn Corp.), consists of a welded titanium tube containing 125I as silver iodide uniformly coated on five silver beads. The dose rate constant and the radial dose function for this source were measured using lithium fluoride thermoluminescent dosimeters in a Solid Water phantom. The value of the dose rate constant is 0.95 cGy h(-1)U(-1) where the unit of air kerma strength is 1 U = 1 cGy h(-1)cm2. The air kerma strength was traceable to the year 2000 primary air kerma strength standard for the model 12501 source at the National Institute of Technology and Standards. The radial dose function for the source was very similar to that for the model 6711 source (manufactured by Nycomed Amersham) for radial distances up to 6 cm. However, the radial dose function is lower in value than that for the model 6702 source (manufactured by Nycomed Amersham) and the model MED3631-A/M Iogold source (manufactured by North American Scientific). PMID:11128306

  14. Effect of tissue composition on dose distribution in brachytherapy with various photon emitting sources

    PubMed Central

    Ghorbani, Mahdi; Salahshour, Fateme; Haghparast, Abbas; Knaup, Courtney

    2014-01-01

    Purpose The aim of this study is to compare the dose in various soft tissues in brachytherapy with photon emitting sources. Material and methods 103Pd, 125I, 169Yb, 192Ir brachytherapy sources were simulated with MCNPX Monte Carlo code, and their dose rate constant and radial dose function were compared with the published data. A spherical phantom with 50 cm radius was simulated and the dose at various radial distances in adipose tissue, breast tissue, 4-component soft tissue, brain (grey/white matter), muscle (skeletal), lung tissue, blood (whole), 9-component soft tissue, and water were calculated. The absolute dose and relative dose difference with respect to 9-component soft tissue was obtained for various materials, sources, and distances. Results There was good agreement between the dosimetric parameters of the sources and the published data. Adipose tissue, breast tissue, 4-component soft tissue, and water showed the greatest difference in dose relative to the dose to the 9-component soft tissue. The other soft tissues showed lower dose differences. The dose difference was also higher for 103Pd source than for 125I, 169Yb, and 192Ir sources. Furthermore, greater distances from the source had higher relative dose differences and the effect can be justified due to the change in photon spectrum (softening or hardening) as photons traverse the phantom material. Conclusions The ignorance of soft tissue characteristics (density, composition, etc.) by treatment planning systems incorporates a significant error in dose delivery to the patient in brachytherapy with photon sources. The error depends on the type of soft tissue, brachytherapy source, as well as the distance from the source. PMID:24790623

  15. Measurements of distributed polarized radio sources from spinning spacecraft - Effect of a tilted axial antenna ISEE-3 application and results

    NASA Technical Reports Server (NTRS)

    Fainberg, J.; Hoang, S.; Manning, R.

    1985-01-01

    An analysis is presented of the system response of a satellite receiver-antenna system to locate a radio source when the satellite is tilted on its axis. The satellite is spin stabilized but experiences a tilt due to either a mechanical misalignment or a shift in the electrical axis caused by parasitic currents in other spacecraft structures. The shorter the antenna, the more significant the effects. Numerical techniques are developed for obtaining the Stokes parameters and the angular parameters of a uniform conical source sensed by a linear antenna in order to derive the average power response of a synthesized dipole to a point on a distributed polarized source. Relative gains are calculated along the antenna at different angles to the source. The techniques are applied to sample ISEE-3 satellite data for Type III solar radio bursts which were sensed by an axial and an equatorial antenna. The two antennas permit localization of the source and quantification of the polarization and angular extent of the source. The resulting high precision in calculations of all three source parameters commends use of the model in analyses of data from the planned ULYSSES mission.

  16. Spatial distribution of HTO activity in unsaturated soil depth in the vicinity of long-term release source

    SciTech Connect

    Golubev, A.; Golubeva, V.; Mavrin, S.

    2015-03-15

    Previous studies reported about a correlation between HTO activity distribution in unsaturated soil layer and atmospheric long-term releases of HTO in the vicinity of Savannah River Site. The Tritium Working Group of BIOMASS Programme has performed a model-model intercomparison study of HTO transport from atmosphere to unsaturated soil and has evaluated HTO activity distribution in the unsaturated soil layer in the vicinity of permanent atmospheric sources. The Tritium Working Group has also reported about such a correlation, however the conclusion was that experimental data sets are needed to confirm this conclusion and also to validate appropriate computer models. (authors)

  17. The effect of the dynamic surface bareness on dust source function, emission, and distribution

    NASA Astrophysics Data System (ADS)

    Kim, Dongchul; Chin, Mian; Bian, Huisheng; Tan, Qian; Brown, Molly E.; Zheng, Tai; You, Renjie; Diehl, Tomas; Ginoux, Paul; Kucsera, Tom

    2013-01-01

    In this study we report the development of a time dependency of global dust source and its impact on dust simulation in the Goddard Chemistry Aerosol Radiation and Transport (GOCART) model. We determine the surface bareness using the 8 km normalized difference vegetation index (NDVI) observed from the advanced very high resolution radiometer satellite. The results are used to analyze the temporal variations of surface bareness in 22 global dust source regions. One half of these regions can be considered permanent dust source regions where NDVI is always less than 0.15, while the other half shows substantial seasonality of NDVI. This NDVI-based surface bareness map is then used, along with the soil and topographic characteristics, to construct a dynamic dust source function for simulating dust emissions with the GOCART model. We divide the 22 dust source regions into three groups of (I) permanent desert, (II) seasonally changing bareness that regulates dust emissions, and (III) seasonally changing bareness that has little effect on dust emission. Compared with the GOCART results with the previously employed static dust source function, the simulation with the new dynamic source function shows significant improvements in category II regions. Even though the global improvement of the aerosol optical depth (AOD) is rather small when compared with satellite and ground-based remote sensing observations, we found a clear and significant effect of the new dust source on seasonal variation of dust emission and dust optical depth near the source regions. Globally, we have found that the permanent bare land contributes to 88% of the total dust emission, whereas the grassland and cultivated crops land contribute to about 12%. Our results suggest the potential of using NDVI over a vegetated area to link the dust emission with land cover and land use change for air quality and climate change studies.

  18. Resting state theta band source distribution and functional connectivity in remitted schizophrenia.

    PubMed

    Shreekantiah Umesh, D; Tikka, Sai Krishna; Goyal, Nishant; Nizamie, S Haque; Sinha, Vinod Kumar

    2016-09-01

    Increased resting theta activity is one consistent observation occurring during all the phases of schizophrenia. However, the resting theta oscillations during the remission phase are yet unclear. We studied resting theta current source density and functional connectivity in remitted schizophrenia and compared with healthy controls. Significantly increased current source density was found in the dominant anterior cingulate cortex. Increased connectivity between the inferior parietal lobe bilaterally and between the left inferior parietal lobe and right middle frontal gyrus was also found. It may be concluded that schizophrenia patients have aberrant regional theta band current source density and functional connectivity even during remission. PMID:27484634

  19. AC magnetohydrodynamic microfluidic switch

    SciTech Connect

    Lemoff, A V; Lee, A P

    2000-03-02

    A microfluidic switch has been demonstrated using an AC Magnetohydrodynamic (MHD) pumping mechanism in which the Lorentz force is used to pump an electrolytic solution. By integrating two AC MHD pumps into different arms of a Y-shaped fluidic circuit, flow can be switched between the two arms. This type of switch can be used to produce complex fluidic routing, which may have multiple applications in {micro}TAS.

  20. ACS Symposium Support

    SciTech Connect

    Kenneth D. Jordan

    2010-02-20

    The funds from this DOE grant were used to help cover the travel costs of five students and postdoctoral fellows who attended a symposium on 'Hydration: From Clusters to Aqueous Solutions' held at the Fall 2007 American Chemical Society Meeting in Boston, MA, August 19-23. The Symposium was sponsored by the Physical Chemistry Division, ACS. The technical program for the meeting is available at http://phys-acs.org/fall2007.html.

  1. 40 CFR Appendixes A-C to Part 403 - [Reserved

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 29 2011-07-01 2009-07-01 true A Appendixes A-C to Part 403 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GENERAL PRE-TREAT-MENT REGULATIONS FOR EXIST-ING AND NEW SOURCES OF POLLUTION Appendixes A-C to Part 403...

  2. 40 CFR Appendixes A-C to Part 403 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 28 2010-07-01 2010-07-01 true A Appendixes A-C to Part 403 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GENERAL PRE-TREAT-MENT REGULATIONS FOR EXIST-ING AND NEW SOURCES OF POLLUTION Appendixes A-C to Part 403...

  3. Polycyclic Aromatic Hydrocarbons in Coastal Sediment of Klang Strait, Malaysia: Distribution Pattern, Risk Assessment and Sources

    PubMed Central

    Tavakoly Sany, Seyedeh Belin; Hashim, Rosli; Salleh, Aishah; Rezayi, Majid; Mehdinia, Ali; Safari, Omid

    2014-01-01

    Concentration, source, and ecological risk of polycyclic aromatic hydrocarbons (PAHs) were investigated in 22 stations from surface sediments in the areas of anthropogenic pollution in the Klang Strait (Malaysia). The total PAH level in the Klang Strait sediment was 994.02±918.1 µg/kg dw. The highest concentration was observed in stations near the coastline and mouth of the Klang River. These locations were dominated by high molecular weight PAHs. The results showed both pyrogenic and petrogenic sources are main sources of PAHs. Further analyses indicated that PAHs primarily originated from pyrogenic sources (coal combustion and vehicular emissions), with significant contribution from petroleum inputs. Regarding ecological risk estimation, only station 13 was moderately polluted, the rest of the stations suffered rare or slight adverse biological effects with PAH exposure in surface sediment, suggesting that PAHs are not considered as contaminants of concern in the Klang Strait. PMID:24747349

  4. Intermediate-wavelength magnetic anomaly field of the North Pacific and posible source distributions

    NASA Technical Reports Server (NTRS)

    Labrecque, J. L.; Cande, S. C.; Jarrard, R. D.

    1985-01-01

    A technique that eliminates external field sources and the effects of strike aliasing was used to extract from marine survey data the intermediate wavelength magnetic anomaly field for (B) in the North Pacific. A strong correlation exists between this field and the Magsat field although a directional sensitivity in the Magsat field can be detected. The intermediate wavelength field is correlated to tectonic features. Island arcs appear as positive anomalies of induced origin likely due to variations in crustal thickness. Seamount chains and oceanic plateaus also are manifested by strong anomalies. The primary contribution to many of these anomalies appears to be due to a remanent magnetization. The source parameters for the remainder of these features are presently unidentified ambiguous. Results indicate that the sea surface field is a valuable source of information for secular variation analysis and the resolution of intermediate wavelength source parameters.

  5. The intermediate wavelength magnetic anomaly field of the north Pacific and possible source distributions

    NASA Technical Reports Server (NTRS)

    Labrecque, J. L.; Cande, S. C.; Jarrard, R. D. (Principal Investigator)

    1983-01-01

    A technique that eliminates external field sources and the effects of strike aliasing was used to extract from marine survey data the intermediate wavelength magnetic anomaly field for (B) in the North Pacific. A strong correlation exists between this field and the MAGSAT field although a directional sensitivity in the MAGSAT field can be detected. The intermediate wavelength field is correlated to tectonic features. Island arcs appear as positive anomalies of induced origin likely due to variations in crustal thickness. Seamount chains and oceanic plateaus also are manifested by strong anomalies. The primary contribution to many of these anomalies appears to be due to a remanent magnetization. The source parameters for the remainder of these features are presently unidentified ambiguous. Results indicate that the sea surface field is a valuable source of information for secular variation analysis and the resolution of intermediate wavelength source parameters.

  6. Video Programs; A Source Guide of Organizations Distributing Video Programs for Use in "Adult Education".

    ERIC Educational Resources Information Center

    Winslow, Ken, Comp.

    Names of selected organizations providing video materials for use in adult education are listed alphabetically. Each entry includes name, address, and telephone number of the distributing organizations; available formats, fee arrangements, clearances, and subject-category description. (SK)

  7. Programmable AC power supply for simulating power transient expected in fusion reactor

    SciTech Connect

    Halimi, B.; Suh, K. Y.

    2012-07-01

    This paper focus on control engineering of the programmable AC power source which has capability to simulate power transient expected in fusion reactor. To generate the programmable power source, AC-AC power electronics converter is adopted to control the power of a set of heaters to represent the transient phenomena of heat exchangers or heat sources of a fusion reactor. The International Thermonuclear Experimental Reactor (ITER) plasma operation scenario is used as the basic reference for producing this transient power source. (authors)

  8. SoundCompass: a distributed MEMS microphone array-based sensor for sound source localization.

    PubMed

    Tiete, Jelmer; Domínguez, Federico; da Silva, Bruno; Segers, Laurent; Steenhaut, Kris; Touhafi, Abdellah

    2014-01-01

    Sound source localization is a well-researched subject with applications ranging from localizing sniper fire in urban battlefields to cataloging wildlife in rural areas. One critical application is the localization of noise pollution sources in urban environments, due to an increasing body of evidence linking noise pollution to adverse effects on human health. Current noise mapping techniques often fail to accurately identify noise pollution sources, because they rely on the interpolation of a limited number of scattered sound sensors. Aiming to produce accurate noise pollution maps, we developed the SoundCompass, a low-cost sound sensor capable of measuring local noise levels and sound field directionality. Our first prototype is composed of a sensor array of 52 Microelectromechanical systems (MEMS) microphones, an inertial measuring unit and a low-power field-programmable gate array (FPGA). This article presents the SoundCompass's hardware and firmware design together with a data fusion technique that exploits the sensing capabilities of the SoundCompass in a wireless sensor network to localize noise pollution sources. Live tests produced a sound source localization accuracy of a few centimeters in a 25-m2 anechoic chamber, while simulation results accurately located up to five broadband sound sources in a 10,000-m2 open field. PMID:24463431

  9. SoundCompass: A Distributed MEMS Microphone Array-Based Sensor for Sound Source Localization

    PubMed Central

    Tiete, Jelmer; Domínguez, Federico; da Silva, Bruno; Segers, Laurent; Steenhaut, Kris; Touhafi, Abdellah

    2014-01-01

    Sound source localization is a well-researched subject with applications ranging from localizing sniper fire in urban battlefields to cataloging wildlife in rural areas. One critical application is the localization of noise pollution sources in urban environments, due to an increasing body of evidence linking noise pollution to adverse effects on human health. Current noise mapping techniques often fail to accurately identify noise pollution sources, because they rely on the interpolation of a limited number of scattered sound sensors. Aiming to produce accurate noise pollution maps, we developed the SoundCompass, a low-cost sound sensor capable of measuring local noise levels and sound field directionality. Our first prototype is composed of a sensor array of 52 Microelectromechanical systems (MEMS) microphones, an inertial measuring unit and a low-power field-programmable gate array (FPGA). This article presents the SoundCompass’s hardware and firmware design together with a data fusion technique that exploits the sensing capabilities of the SoundCompass in a wireless sensor network to localize noise pollution sources. Live tests produced a sound source localization accuracy of a few centimeters in a 25-m2 anechoic chamber, while simulation results accurately located up to five broadband sound sources in a 10,000-m2 open field. PMID:24463431

  10. The cosmic-ray pathlength distribution at low energy - A new probe of the source/acceleration regions

    NASA Technical Reports Server (NTRS)

    Guzik, T. G.; Wefel, J. P.

    1984-01-01

    Compiled measurements of secondary to primary ratios covering the charge range Z = 3-26 and the energy range 0.05 - 50 GeV/nucleon are analyzed in energy dependent galactic propagation plus solar modulation calculations. The cosmic ray pathlength distribution is shown to consist of two energy dependent components interpreted as representing confinement in the galaxy and confinement in the 'source' regions.

  11. Study of the Large-Scale Distribution of Gamma-Ray Burst Sources by the Method of Pairwise Distances

    NASA Astrophysics Data System (ADS)

    Gerasim, R. V.; Orlov, V. V.; Raikov, A. A.

    2015-06-01

    The method of pairwise distances developed earlier by the authors is used to study the spatial distribution of 352 sources of gamma-ray bursts with measured redshifts. Three cosmological models are considered: a model with a Euclidean metric, the "tired light" model, and the standard ΛCDM model. It is found that this set has fractal features and may be multifractal. The fractal dimensionalities are estimated.

  12. Distribution, partitioning and sources of polycyclic aromatic hydrocarbons in the water-SPM-sediment system of Lake Chaohu, China.

    PubMed

    Qin, Ning; He, Wei; Kong, Xiang-Zhen; Liu, Wen-Xiu; He, Qi-Shuang; Yang, Bin; Wang, Qing-Mei; Yang, Chen; Jiang, Yu-Jiao; Jorgensen, Sven Erik; Xu, Fu-Liu; Zhao, Xiao-Li

    2014-10-15

    The residual levels of polycyclic aromatic hydrocarbons (PAHs) in the water, suspended particular matter (SPM) and sediment from Lake Chaohu were measured with a gas chromatograph-mass spectrometer (GC-MS). The spatial-temporal distributions and the SPM-water partition of PAHs and their influencing factors were investigated. The potential sources and contributions of PAHs in the sediment were estimated by positive matrix factorization (PMF) and probabilistic stable isotopic analysis (PSIA). The results showed that the average residual levels of total PAHs (PAH16) in the water, SPM and sediment were 170.7 ± 70.8 ng/L, 210.7 ± 160.7 ng/L and 908.5 ± 1878.1 ng/g dry weight, respectively. The same spatial distribution trend of PAH16 in the water, SPM and sediment was found from high to low: river inflows>western lake>eastern lake>water source area. There was an obvious seasonal trend of PAH16 in the water, while no obvious seasonal trend was found in the SPM. The residues and distributions of PAHs in the water, SPM and sediment relied heavily on carbon content. Significant Pearson correlations were found between LogKoc and LogKow as well as some hydro-meteorological factors. Three major sources of PAHs including coal and biomass combustions, and vehicle emissions were identified. PMID:25103197

  13. Experimental Verification of Application of Looped System and Centralized Voltage Control in a Distribution System with Renewable Energy Sources

    NASA Astrophysics Data System (ADS)

    Hanai, Yuji; Hayashi, Yasuhiro; Matsuki, Junya

    The line voltage control in a distribution network is one of the most important issues for a penetration of Renewable Energy Sources (RES). A loop distribution network configuration is an effective solution to resolve voltage and distribution loss issues concerned about a penetration of RES. In this paper, for a loop distribution network, the authors propose a voltage control method based on tap change control of LRT and active/reactive power control of RES. The tap change control of LRT takes a major role of the proposed voltage control. Additionally the active/reactive power control of RES supports the voltage control when voltage deviation from the upper or lower voltage limit is unavoidable. The proposed method adopts SCADA system based on measured data from IT switches, which are sectionalizing switch with sensor installed in distribution feeder. In order to check the validity of the proposed voltage control method, experimental simulations using a distribution system analog simulator “ANSWER” are carried out. In the simulations, the voltage maintenance capability in the normal and the emergency is evaluated.

  14. Depth to the bottom of magnetic sources (DBMS) from aeromagnetic data of Central India using modified centroid method for fractal distribution of sources

    NASA Astrophysics Data System (ADS)

    Bansal, A. R.; Anand, S.; Rajaram, M.; Rao, V.; Dimri, V. P.

    2012-12-01

    The depth to the bottom of the magnetic sources (DBMS) may be used as an estimate of the Curie - point depth. The DBMSs can also be interpreted in term of thermal structure of the crust. The thermal structure of the crust is a sensitive parameter and depends on the many properties of crust e.g. modes of deformation, depths of brittle and ductile deformation zones, regional heat flow variations, seismicity, subsidence/uplift patterns and maturity of organic matter in sedimentary basins. The conventional centroid method of DBMS estimation assumes random uniform uncorrelated distribution of sources and to overcome this limitation a modified centroid method based on fractal distribution has been proposed. We applied this modified centroid method to the aeromagnetic data of the central Indian region and selected 29 half overlapping blocks of dimension 200 km x 200 km covering different parts of the central India. Shallower values of the DBMS are found for the western and southern portion of Indian shield. The DBMSs values are found as low as close to middle crust in the south west Deccan trap and probably deeper than Moho in the Chhatisgarh basin. In few places DBMS are close to the Moho depth found from the seismic study and others places shallower than the Moho. The DBMS indicate complex nature of the Indian crust.

  15. Improving Continuous-Variable Quantum Key Distribution Using the Heralded Noiseless Linear Amplifier with Source in the Middle

    NASA Astrophysics Data System (ADS)

    Liang, Jianwu; Zhou, Jian; Shi, Jinjing; He, Guangqiang; Guo, Ying

    2016-02-01

    We characterize the efficiency of the practical continuous-variable quantum key distribution (CVQKD) while inserting the heralded noiseless linear amplifier (NLA) before detectors to increase the secret key rate and the maximum transmission distance in Gaussian channels. In the heralded NLA-based CVQKD system, the entanglement source is only placed in the middle while the two participants are unnecessary to trust their source. The intensities of source noise are sensitive to the tunable NLA with the parameter g in a suitable range and can be stabilized to the suitable constant values to eliminate the impact of channel noise and defeat the potential attacks. Simulation results show that there is a well balance between the secret key rate and the maximum transmission distance with the tunable NLA.

  16. The effect of the random distribution of electronic components in the output characteristics of the Howland current source

    NASA Astrophysics Data System (ADS)

    Bertemes-Filho, P.; Felipe, A.

    2013-04-01

    When a Howland source is designed, the components are chosen so that the designed source has the desired characteristics. However, the operational amplifier limitations and resistor tolerances causes undesired behaviours. This work proposes to take in account the influence of the random distribution of the commercial resistors in the Howland circuit over the frequency range of 10 Hz to 10 MHz. The probability density function due to small changes over the resistors was calculated by using an analytical model. Results show that both output current and impedance are very sensitive to the resistor tolerances. It is shown that the output impedance is very dependent on the open-loop gain of the Opamp rather than the resistor tolerances, especially at higher frequencies. This might improve the implementations of real current source used in electrical bioimpedance.

  17. Distribution and source of (129)I, (239)(,240)Pu, (137)Cs in the environment of Lithuania.

    PubMed

    Ežerinskis, Ž; Hou, X L; Druteikienė, R; Puzas, A; Šapolaitė, J; Gvozdaitė, R; Gudelis, A; Buivydas, Š; Remeikis, V

    2016-01-01

    Fifty five soil samples collected in the Lithuania teritory in 2011 and 2012 were analyzed for (129)I, (137)Cs and Pu isotopes in order to investigate the level and distribution of artificial radioactivity in Lithuania. The activity and atomic ratio of (238)Pu/((239,24)0)Pu, (129)I/(127)I and (131)I/(137)Cs were used to identify the origin of these radionuclides. The (238)Pu/(239+240)Pu and (240)Pu/(239)Pu ratios in the soil samples analyzed varied in the range of 0.02-0.18 and 0.18-0.24, respectively, suggesting the global fallout as the major source of Pu in Lithuania. The values of 10(-9) to 10(-6) for (129)I/(127)I atomic ratio revealed that the source of (129)I in Lithuania is global fallout in most cases though several sampling sites shows a possible impact of reprocessing releases. Estimated (129)I/(131)I ratio in soil samples from the southern part of Lithuania shows negligible input of the Chernobyl fallout. No correlation of the (137)Cs and Pu isotopes with (129)I was observed, indicating their different sources terms. Results demonstrate uneven distribution of these radionuclides in the Lithuanian territory and several sources of contamination i.e. Chernobyl accident, reprocessing releases and global fallout. PMID:26476410

  18. Distributed Least-Squares Estimation of a Remote Chemical Source via Convex Combination in Wireless Sensor Networks

    PubMed Central

    Cao, Meng-Li; Meng, Qing-Hao; Zeng, Ming; Sun, Biao; Li, Wei; Ding, Cheng-Jun

    2014-01-01

    This paper investigates the problem of locating a continuous chemical source using the concentration measurements provided by a wireless sensor network (WSN). Such a problem exists in various applications: eliminating explosives or drugs, detecting the leakage of noxious chemicals, etc. The limited power and bandwidth of WSNs have motivated collaborative in-network processing which is the focus of this paper. We propose a novel distributed least-squares estimation (DLSE) method to solve the chemical source localization (CSL) problem using a WSN. The DLSE method is realized by iteratively conducting convex combination of the locally estimated chemical source locations in a distributed manner. Performance assessments of our method are conducted using both simulations and real experiments. In the experiments, we propose a fitting method to identify both the release rate and the eddy diffusivity. The results show that the proposed DLSE method can overcome the negative interference of local minima and saddle points of the objective function, which would hinder the convergence of local search methods, especially in the case of locating a remote chemical source. PMID:24977387

  19. Structural controls on source rock distribution and maturation in southeast Turkey

    SciTech Connect

    Reed, J.D.; Ottensman, V.V.; Cushing, G.W. ); Aytuna, S. )

    1990-05-01

    Production from the western part of the Zagros fold and thrust belt southeastern Turkey is characterized by high-sulfur (2-3%) oils from middle Cretaceous Mardin Formation. The oils are generated from two carbonate sources, one from the middle Cretaceous passive margin sequence and one deposited as a part of the Upper Cretaceous foreland basin sequence. Both sources are associated with transgressive events coincident with two recognized Cretaceous oceanic anoxic events in Cenomanian-Turonian and Coniacian-Santonian. Geochemical markers in the oils substantiate the restricted, anoxic conditions characteristic of their source rock deposition. During the Upper Cretaceous compressional event, horsts formed buttresses to advancing oceanic thrust sheets. The oceanic thrust sheets consisted of the Karadut and Kocali formations, oceanic equivalents of the Mesozoic shelf. The middle and Upper Cretaceous source facies were rapidly and deeply buried by the tectonically thickened thrust sheets adjacent to the buttresses. Thick burial by the oceanic rocks was critical for thermal maturation of the sources. Geohistory modeling shows generation occurred during the Tertiary coincidental with tectonic activity that probably allowed oil migration to occur along new or reactivated Cretaceous faults.

  20. Comparison of Particle-Associated Bacteria from a Drinking Water Treatment Plant and Distribution Reservoirs with Different Water Sources

    NASA Astrophysics Data System (ADS)

    Liu, G.; Ling, F. Q.; van der Mark, E. J.; Zhang, X. D.; Knezev, A.; Verberk, J. Q. J. C.; van der Meer, W. G. J.; Medema, G. J.; Liu, W. T.; van Dijk, J. C.

    2016-02-01

    This study assessed the characteristics of and changes in the suspended particles and the associated bacteria in an unchlorinated drinking water distribution system and its reservoirs with different water sources. The results show that particle-associated bacteria (PAB) were present at a level of 0.8-4.5 × 103 cells ml-1 with a biological activity of 0.01-0.04 ng l-1 ATP. Different PAB communities in the waters produced from different sources were revealed by a 16S rRNA-based pyrosequencing analysis. The quantified biomass underestimation due to the multiple cells attached per particle was ≥ 85%. The distribution of the biologically stable water increased the number of cells per particle (from 48 to 90) but had minor effects on the PAB community. Significant changes were observed at the mixing reservoir. Our results show the characteristics of and changes in suspended PAB during distribution, and highlight the significance of suspended PAB in the distribution system, because suspended PAB can lead to a considerable underestimation of biomass, and because they exist as biofilm, which has a greater mobility than pipe-wall biofilm and therefore presents a greater risk, given the higher probability that it will reach the customers’ taps and be ingested.

  1. Comparison of Particle-Associated Bacteria from a Drinking Water Treatment Plant and Distribution Reservoirs with Different Water Sources.

    PubMed

    Liu, G; Ling, F Q; van der Mark, E J; Zhang, X D; Knezev, A; Verberk, J Q J C; van der Meer, W G J; Medema, G J; Liu, W T; van Dijk, J C

    2016-01-01

    This study assessed the characteristics of and changes in the suspended particles and the associated bacteria in an unchlorinated drinking water distribution system and its reservoirs with different water sources. The results show that particle-associated bacteria (PAB) were present at a level of 0.8-4.5 × 10(3) cells ml(-1) with a biological activity of 0.01-0.04 ng l(-1) ATP. Different PAB communities in the waters produced from different sources were revealed by a 16S rRNA-based pyrosequencing analysis. The quantified biomass underestimation due to the multiple cells attached per particle was ≥ 85%. The distribution of the biologically stable water increased the number of cells per particle (from 48 to 90) but had minor effects on the PAB community. Significant changes were observed at the mixing reservoir. Our results show the characteristics of and changes in suspended PAB during distribution, and highlight the significance of suspended PAB in the distribution system, because suspended PAB can lead to a considerable underestimation of biomass, and because they exist as biofilm, which has a greater mobility than pipe-wall biofilm and therefore presents a greater risk, given the higher probability that it will reach the customers' taps and be ingested. PMID:26832989

  2. Size distributions of polycyclic aromatic hydrocarbons in urban atmosphere: sorption mechanism and source contributions to respiratory deposition

    NASA Astrophysics Data System (ADS)

    Lv, Yan; Li, Xiang; Xu, Ting Ting; Cheng, Tian Tao; Yang, Xin; Chen, Jian Min; Iinuma, Yoshiteru; Herrmann, Hartmut

    2016-03-01

    In order to better understand the particle size distribution of polycyclic aromatic hydrocarbons (PAHs) and their source contribution to human respiratory system, size-resolved PAHs have been studied in ambient aerosols at a megacity Shanghai site during a 1-year period (2012-2013). The results showed the PAHs had a bimodal distribution with one mode peak in the fine-particle size range (0.4-2.1 µm) and another mode peak in the coarse-particle size range (3.3-9.0 µm). Along with the increase in ring number of PAHs, the intensity of the fine-mode peak increased, while the coarse-mode peak decreased. Plotting of log(PAH / PM) against log(Dp) showed that all slope values were above -1, suggesting that multiple mechanisms (adsorption and absorption) controlled the particle size distribution of PAHs. The total deposition flux of PAHs in the respiratory tract was calculated as being 8.8 ± 2.0 ng h-1. The highest lifetime cancer risk (LCR) was estimated at 1.5 × 10-6, which exceeded the unit risk of 10-6. The LCR values presented here were mainly influenced by accumulation mode PAHs which came from biomass burning (24 %), coal combustion (25 %), and vehicular emission (27 %). The present study provides us with a mechanistic understanding of the particle size distribution of PAHs and their transport in the human respiratory system, which can help develop better source control strategies.

  3. Comparison of Particle-Associated Bacteria from a Drinking Water Treatment Plant and Distribution Reservoirs with Different Water Sources

    PubMed Central

    Liu, G.; Ling, F. Q.; van der Mark, E. J.; Zhang, X. D.; Knezev, A.; Verberk, J. Q. J. C.; van der Meer, W. G. J.; Medema, G. J.; Liu, W. T.; van Dijk, J. C.

    2016-01-01

    This study assessed the characteristics of and changes in the suspended particles and the associated bacteria in an unchlorinated drinking water distribution system and its reservoirs with different water sources. The results show that particle-associated bacteria (PAB) were present at a level of 0.8–4.5 × 103 cells ml−1 with a biological activity of 0.01–0.04 ng l−1 ATP. Different PAB communities in the waters produced from different sources were revealed by a 16S rRNA-based pyrosequencing analysis. The quantified biomass underestimation due to the multiple cells attached per particle was ≥ 85%. The distribution of the biologically stable water increased the number of cells per particle (from 48 to 90) but had minor effects on the PAB community. Significant changes were observed at the mixing reservoir. Our results show the characteristics of and changes in suspended PAB during distribution, and highlight the significance of suspended PAB in the distribution system, because suspended PAB can lead to a considerable underestimation of biomass, and because they exist as biofilm, which has a greater mobility than pipe-wall biofilm and therefore presents a greater risk, given the higher probability that it will reach the customers’ taps and be ingested. PMID:26832989

  4. Identifying and characterizing major emission point sources as a basis for geospatial distribution of mercury emissions inventories

    NASA Astrophysics Data System (ADS)

    Steenhuisen, Frits; Wilson, Simon J.

    2015-07-01

    Mercury is a global pollutant that poses threats to ecosystem and human health. Due to its global transport, mercury contamination is found in regions of the Earth that are remote from major emissions areas, including the Polar regions. Global anthropogenic emission inventories identify important sectors and industries responsible for emissions at a national level; however, to be useful for air transport modelling, more precise information on the locations of emission is required. This paper describes the methodology applied, and the results of work that was conducted to assign anthropogenic mercury emissions to point sources as part of geospatial mapping of the 2010 global anthropogenic mercury emissions inventory prepared by AMAP/UNEP. Major point-source emission sectors addressed in this work account for about 850 tonnes of the emissions included in the 2010 inventory. This work allocated more than 90% of these emissions to some 4600 identified point source locations, including significantly more point source locations in Africa, Asia, Australia and South America than had been identified during previous work to geospatially-distribute the 2005 global inventory. The results demonstrate the utility and the limitations of using existing, mainly public domain resources to accomplish this work. Assumptions necessary to make use of selected online resources are discussed, as are artefacts that can arise when these assumptions are applied to assign (national-sector) emissions estimates to point sources in various countries and regions. Notwithstanding the limitations of the available information, the value of this procedure over alternative methods commonly used to geo-spatially distribute emissions, such as use of 'proxy' datasets to represent emissions patterns, is illustrated. Improvements in information that would facilitate greater use of these methods in future work to assign emissions to point-sources are discussed. These include improvements to both national

  5. Distribution of aquifers, liquid-waste impoundments, and municipal water-supply sources, Massachusetts

    USGS Publications Warehouse

    Delaney, David F.; Maevsky, Anthony

    1980-01-01

    Impoundments of liquid waste are potential sources of ground-water contamination in Massachusetts. The map report, at a scale of 1 inch equals 4 miles, shows the idstribution of aquifers and the locations of municipal water-supply sources and known liquid-waste impoundments. Ground water, an important source of municipal water supply, is produced from shallow sand and gravel aquifers that are generally unconfined, less than 200 feet thick, and yield less than 2,000 gallons per minute to individual wells. These aquifers commonly occupy lowlands and stream valleys and are most extensive in eastern Massachusetts. Surface impoundments of liquid waste are commonly located over these aquifers. These impoundments may leak and allow waste to infiltrate underlying aquifers and alter their water quality. (USGS)

  6. Absorption and Attenuation Coefficients Using the WET Labs ac-s in the Mid-Atlantic Bight: Field Measurements and Data Analysis

    NASA Technical Reports Server (NTRS)

    Ohi, Nobuaki; Makinen, Carla P.; Mitchell, Richard; Moisan, Tiffany A.

    2008-01-01

    Ocean color algorithms are based on the parameterization of apparent optical properties as a function of inherent optical properties. WET Labs underwater absorption and attenuation meters (ac-9 and ac-s) measure both the spectral beam attenuation [c (lambda)] and absorption coefficient [a (lambda)]. The ac-s reports in a continuous range of 390-750 nm with a band pass of 4 nm, totaling approximately 83 distinct wavelengths, while the ac-9 reports at 9 wavelengths. We performed the ac-s field measurements at nine stations in the Mid-Atlantic Bight from water calibrations to data analysis. Onboard the ship, the ac-s was calibrated daily using Milli Q-water. Corrections for the in situ temperature and salinity effects on optical properties of water were applied. Corrections for incomplete recovery of the scattered light in the ac-s absorption tube were performed. The fine scale of spectral and vertical distributions of c (lambda) and a (lambda) were described from the ac-s. The significant relationships between a (674) and that of spectrophotometric analysis and chlorophyll a concentration of discrete water samples were observed.

  7. Demonstration of a distributed directed infrared countermeasure source: the multifunctional laser

    NASA Astrophysics Data System (ADS)

    Delmonte, T.; Watson, M. A.; O'Driscoll, E. J.; Hand, D. P.

    2008-10-01

    In current laser countermeasure technology concepts where frequency conversion is required, each active component has its own laser source. During this paper we show that by using microstructured fibre technology as a delivery system, output in multiple wavebands can be efficiently generated at locations remote from the laser pump source. We demonstrate that laser radiation (with specifications close to those currently on airframes) can be delivered without significant spectral, temporal or modal degradation over lengths representative of that in an airframe. This fibre delivered radiation is used as a pump source for active frequency conversion, generating tuneable laser output in the 2 μm, 3.5 μm and 0.532 μm regions, i.e. in wavebands of interest to countermeasure applications. A Nd:YVO4 laser (λ = 1.064 μm) with 16 W of average power in a train of 15 ns pulses acts as the single pump source for our system. Different types of microstructured fibre are assessed for high power delivery over lengths greater than 6.5 m. Three frequency conversion devices were constructed here to demonstrate the quality of the fibre-delivered radiation - the devices are all based around periodically poled lithium niobate (PPLN) crystals and consist of two optical parametric oscillators converting the pump source to wavelengths of ~2 μm and ~3.5 μm and a second harmonic generator to double the frequency to 0.532 μm. The efficiencies of the frequency conversion sources are comparable whether radiation is delivered through free space or by microstructured fibre.

  8. Source attribution, physicochemical properties and spatial distribution of wet deposited mercury to the Ohio River valley

    NASA Astrophysics Data System (ADS)

    White, Emily Mae

    Mercury (Hg) is a bioaccumulative neurotoxin that is emitted from anthropogenic sources through fossil fuel combustion. The spatial scale of atmospheric transport prior to deposition is dependent on the chemical and physical form of Hg emissions, and has yet to be quantitatively defined. A five-year comprehensive Hg monitoring and source apportionment study was conducted in Steubenville, Ohio to investigate atmospheric Hg deposition to the highly industrialized Ohio River Valley region. Long-term event-precipitation measurements revealed a significant 30% to three-fold enrichment of Hg concentrations and total Hg deposition flux to the Steubenville site over other Great Lakes regional sites. Multivariate receptor models attributed ˜70% of Hg wet deposition to local coal combustion sources. While local stagnant atmospheric conditions led to moderately high volume-weighted mean Hg concentrations and the majority of Hg wet deposition flux, regional transport from the Chicago/Gary and Detroit/Windsor urban areas also led to elevated precipitation Hg concentrations, but did not contribute significantly to the overall Hg deposition. The degree of local source influence was established during a summertime field intensive study in which a local scale network of concurrently collected rain samples revealed that 42% of Hg wet deposition measured less than one km from the base of coal fired utilities could be attributed to the adjacent source, corresponding to 170% Hg concentration enhancement over regionally representative precipitation collected concurrently. In addition, 69+/-37% of the Hg collected in rain was in a soluble form, entering the precipitation as reactive gas phase or fine particle associated Hg. The Hg scavenging coefficient (rate of concentration reduction throughout a single precipitation event) was particularly low when compared to other trace elements. Furthermore, when compared to an upwind but non-locally source impacted site, the scavenging

  9. SEI power source alternatives for rovers and other multi-kWe distributed surface applications

    NASA Technical Reports Server (NTRS)

    Bents, David J.; Kohout, L. L.; Mckissock, Barbara I.; Rodriguez, C. D.; Withrow, C. A.; Colozza, A.; Hanlon, James C.; Schmitz, Paul C.

    1991-01-01

    To support the Space Exploration Initiative (SEI), a study was performed to investigate power system alternatives for the rover vehicles and servicers that were subsequently generated for each of these rovers and servicers, candidate power sources incorporating various power generation and energy storage technologies were identified. The technologies were those believed most appropriate to the SEI missions, and included solar, electrochemical, and isotope systems. The candidates were characterized with respect to system mass, deployed area, and volume. For each of the missions a preliminary selection was made. Results of this study depict the available power sources in light of mission requirements as they are currently defined.

  10. Analysis of large-scale distributed knowledge sources via autonomous cooperative graph mining

    NASA Astrophysics Data System (ADS)

    Levchuk, Georgiy; Ortiz, Andres; Yan, Xifeng

    2014-05-01

    In this paper, we present a model for processing distributed relational data across multiple autonomous heterogeneous computing resources in environments with limited control, resource failures, and communication bottlenecks. Our model exploits dependencies in the data to enable collaborative distributed querying in noisy data. The collaboration policy for computational resources is efficiently constructed from the belief propagation algorithm. To scale to large data sizes, we employ a combination of priority-based filtering, incremental processing, and communication compression techniques. Our solution achieved high accuracy of analysis results and orders of magnitude improvements in computation time compared to the centralized graph matching solution.

  11. Wall-loss distribution of charge breeding ions in an electron cyclotron resonance ion source

    SciTech Connect

    Jeong, S. C.; Oyaizu, M.; Imai, N.; Hirayama, Y.; Ishiyama, H.; Miyatake, H.; Niki, K.; Okada, M.; Watanabe, Y. X.; Otokawa, Y.; Osa, A.; Ichikawa, S.

    2012-02-15

    We investigated the ion-loss distribution on the sidewall of an electron cyclotron resonance (ECR) plasma chamber using the 18-GHz ECR charge breeder at the Tokai Radioactive Ion Accelerator Complex (TRIAC). Similarities and differences between the ion-loss distributions (longitudinal and azimuthal) of different ion species (i.e., radioactive {sup 111}In{sup 1+} and {sup 140}Xe{sup 1+} ions that are typical volatile and nonvolatile elements) was qualitatively discussed to understand the element dependence of the charge breeding efficiency. Especially, the similarities represent universal ion loss characteristics in an ECR charge breeder, which are different from the loss patterns of electrons on the ECRIS wall.

  12. Design and characterization of a spatially distributed multibeam field emission x-ray source for stationary digital breast tomosynthesis

    PubMed Central

    Qian, Xin; Rajaram, Ramya; Calderon-Colon, Xiomara; Yang, Guang; Phan, Tuyen; Lalush, David S.; Lu, Jianping; Zhou, Otto

    2009-01-01

    Digital breast tomosynthesis (DBT) is a limited angle computed tomography technique that can distinguish tumors from its overlying breast tissues and has potentials for detection of cancers at a smaller size and earlier stage. Current prototype DBT scanners are based on the regular full-field digital mammography systems and require partial isocentric motion of an x-ray tube over certain angular range to record the projection views. This prolongs the scanning time and, in turn, degrades the imaging quality due to motion blur. To mitigate the above limitations, the concept of a stationary DBT (s-DBT) scanner has been recently proposed based on the newly developed spatially distributed multibeam field emission x-ray (MBFEX) source technique using the carbon nanotube. The purpose of this article is to evaluate the performance of the 25-beam MBFEX source array that has been designed and fabricated for the s-DBT system. The s-DBT system records all the projection images by electronically activating the multiple x-ray beams from different viewing angles without any mechanical motion. The configuration of the MBFEX source is close to the published values from the Siemens Mammomat system. The key issues including the x-ray flux, focal spot size, spatial resolution, scanning time, beam-to-beam consistency, and reliability are evaluated using the standard procedures. In this article, the authors describe the design and performance of a distributed x-ray source array specifically designed for the s-DBT system. They evaluate the emission current, current variation, lifetime, and focal spot sizes of the source array. An emission current of up to 18 mA was obtained at 0.5×0.3 mm effective focal spot size. The experimentally measured focal spot sizes are comparable to that of a typical commercial mammography tube without motion blurring. Trade-off between the system spatial resolution, x-ray flux, and scanning time are also discussed. Projection images of a breast phantom were

  13. Design and characterization of a spatially distributed multibeam field emission x-ray source for stationary digital breast tomosynthesis

    SciTech Connect

    Qian Xin; Rajaram, Ramya; Calderon-Colon, Xiomara; Yang Guang; Phan, Tuyen; Lalush, David S.; Lu Jianping; Zhou, Otto

    2009-10-15

    Digital breast tomosynthesis (DBT) is a limited angle computed tomography technique that can distinguish tumors from its overlying breast tissues and has potentials for detection of cancers at a smaller size and earlier stage. Current prototype DBT scanners are based on the regular full-field digital mammography systems and require partial isocentric motion of an x-ray tube over certain angular range to record the projection views. This prolongs the scanning time and, in turn, degrades the imaging quality due to motion blur. To mitigate the above limitations, the concept of a stationary DBT (s-DBT) scanner has been recently proposed based on the newly developed spatially distributed multibeam field emission x-ray (MBFEX) source technique using the carbon nanotube. The purpose of this article is to evaluate the performance of the 25-beam MBFEX source array that has been designed and fabricated for the s-DBT system. The s-DBT system records all the projection images by electronically activating the multiple x-ray beams from different viewing angles without any mechanical motion. The configuration of the MBFEX source is close to the published values from the Siemens Mammomat system. The key issues including the x-ray flux, focal spot size, spatial resolution, scanning time, beam-to-beam consistency, and reliability are evaluated using the standard procedures. In this article, the authors describe the design and performance of a distributed x-ray source array specifically designed for the s-DBT system. They evaluate the emission current, current variation, lifetime, and focal spot sizes of the source array. An emission current of up to 18 mA was obtained at 0.5x0.3 mm effective focal spot size. The experimentally measured focal spot sizes are comparable to that of a typical commercial mammography tube without motion blurring. Trade-off between the system spatial resolution, x-ray flux, and scanning time are also discussed. Projection images of a breast phantom were

  14. Steady temperature and density distributions in a gas containing heat sources

    NASA Technical Reports Server (NTRS)

    Davison, H. W.

    1971-01-01

    Computer program, STADDIG, is based on steady state, one dimensional heat transfer calculation using cylindrical coordinates. Program allows for conduction across gas and container walls. Heat is dissipated from walls by forced convection cooling with incompressible coolant. Heat sources are included in coolant, gas, and walls.

  15. TROPOSPHERIC NITROGEN: THE INFLUENCE OF ANTHROPOGENIC SOURCES ON DISTRIBUTIONS AND DEPOSITION

    EPA Science Inventory

    A general circulation model is used to provide three.dimensional global winds, vertical convective mass transport and precipitation fields for modeling the transport of reactive nitrogen and its removal by precipitation. ajor sources of NOx include lightning, soil microbial activ...

  16. NOVEL STATISTICAL APPROACH TO EVALUATE SPATIAL DISTRIBUTION OF PM FROM SPECIFIC SOURCE CATEGORIES

    EPA Science Inventory

    This task addresses aspects of NRC recommendations 10A and 10B. Positive matrix factorization (PMF) is a new statistical techniques for determining the daily contribution to PM mass of specific source categories (auto exhaust, smelters, suspended soil, secondary sulfate, etc.). I...

  17. Funding Disparities and the Inequitable Distribution of Teachers: Evaluating Sources and Solutions

    ERIC Educational Resources Information Center

    Adamson, Frank; Darling-Hammond, Linda

    2012-01-01

    The inequitable distribution of well-qualified teachers to students in the United States is a longstanding issue. Despite federal mandates under the No Child Left Behind Act and the use of a range of incentives to attract teachers to high-need schools, the problem remains acute in many states. This study examines how and why teacher quality is…

  18. STUDY ON THE FEASIBILITY AND DESIGN OF AUTOMATIC PARTICULATE SIZE DISTRIBUTION ANALYZER FOR SOURCE EMISSIONS

    EPA Science Inventory

    The objective of this program was to evolve a method for the automatic determination of the size distribution of particulates within stack gas effluent streams. This device was designed to cover the typical mass concentration range encountered upstream as well as downstream of em...

  19. The spatial distributions of the sources of UV solar Explosive Events at different velocities

    NASA Astrophysics Data System (ADS)

    Mendoza-Torres, J. E.

    2013-01-01

    We analyze five solar Explosive Events observed in the Si IV emission line at 139.37 nm during SUMER/SoHO raster scans near disk center. The Doppler velocities from -45 km s-1 to +45 km s-1 were sorted into eleven symmetrically organized velocity bins, five equally-sized bins on each side and one bin for the line at rest. The radiance values along the NS oriented slit around the maximum of each EE are used to build one-dimensional distributions. We study these distributions and their development in space and time for different velocity bins to unveil the 3D-structure and evolution of Explosive Events. The spatial radiance distributions for the EE maximum and around it were made. For some Explosive Events the dispersion direction is not oriented orthogonally to the slit direction; consequently, the blueshifted emission is in a linear way offset from the redshifted emission by several pixels. The largest offset (˜5″) is observed between distributions whose velocities differ by ˜36 km s-1. The linear relation agrees with an scenario of flows inside magnetic arcs.

  20. ATMOSPHERIC DISTRIBUTIONS, SOURCES AND SINKS OF SELECTED HALOCARBONS, HYDROCARBONS, SF6, AND N20

    EPA Science Inventory

    Global distributions of a large number of halocarbons, hydrocarbons, SF6, and N2O are presented. These data are complemented with measurements in the polluted environments to establish urban-nonurban relationships of these species. Atmospheric growth rates of selected species are...

  1. Spatial Distribution, Sources, and Age of Sedimentary Carbon in Lake Malawi, East Africa

    NASA Astrophysics Data System (ADS)

    Kruger, B. R.; Minor, E. C.; Werne, J. P.; Johnson, T. C.

    2011-12-01

    Currently, the source of organic matter to surface sediments of Lake Malawi (East Africa) is unclear; studies of offshore north-basin cores (363 m to 403 m water depth) have produced conflicting results regarding the proportion of aquatic versus terrestrial organic carbon (OC) contained in these sediments. To address this question, ten multi-cores were recovered from the north basin of Lake Malawi along a transect that follows a major river delta into the lake's deep basin, from 82 m to 386 m water depth. Bulk surface sediment data indicate that while the C/N ratio of organic matter decreases with distance from shore (ranging from 9.8 to 8.3, R2 = 0.58), and stable carbon isotope values become increasingly 13C-depleted (ranging from -21.65 to -25.25, R2 = 0.80), the concentration of OC (wt %) generally increases (ranging from 1.9% to 4.5%, R2 = 0.77). These combined trends suggest substantial carbon contribution from aquatic sources, particularly in the deeper-water, open-lake sites. This trend is supported by preliminary biomarker results. N-alcohols from surface sediments were isolated and grouped into aquatically sourced (C20, C22, and C24) and terrestrially sourced (C28 and C30) fractions for quantification as well as radiocarbon dating. N-alcohol abundance results indicate consistent contribution of terrestrial n-alcohols to surface sediments as distance from shore increases, while aquatic n-alcohol input appears to increase. Preliminary results from compound class specific radiocarbon dating indicate that aquatically sourced n-alcohols isolated from surface sediments may be significantly aged relative to bulk surface sediment.

  2. Organic geochemistry of lower Tertiary shales of southern Louisiana: Regional distribution of source potential

    SciTech Connect

    Chinn, E.W. ); Cole, G.A.; Gibbons, M.J.; Sassen, R.; Drozd, R.J. )

    1990-05-01

    Outer continental shelf shales of the Paleogene/Eocene Wilcox Group and middle Eocene Sparta Formation are potential source rocks for hydrocarbons in southern Louisiana. Eight hundred and thirty-seven shale samples (Sparta 219) Wilcox, 618 from 24 wells across south Louisiana were analyzed using Rock-Eval pyrolysis; 24 organic-rich samples were analyzed using pyrolysis-gas chromatography and gas chromatography-mass spectrometry (GC-MS). Regional trends in organic geochemistry are related to two main factors: sedimentary facies transition from proximal deltaic to shelf/slope environments, and thermal maturity. According to geothermal gradient maps, thermal effects increase from east to west across southern Louisiana and from north to south as the lower Tertiary section is buried to greater than 30,000 ft. The Wilcox, and to a lesser extent the Sparta, are major regressive deltaic sequences whose primary deltaic depocenters are located in subsurface Texas. Volumetrically, smaller deltas prograded beyond the ancient Cretaceous shelf edge by as much as 50 mi across southern Louisiana. Source potential in both rock units becomes more oil prone from west to east across south Louisiana, with an apparent maximum in the shelf/slope flexure zone in south central Louisiana. In this area, Sparta Formation shales show good to excellent potential in shales overlain by shelf-edge barrier sands. Wilcox source potential is fair to good in shales deposited in submarine fan environments. Source units are interpreted to be a product of transgressive episodes occurring within primarily regressive sequences. The close proximity of source units to the shelf-edge suggest that they may represent conditions deeper in the Eocene Gulf of Mexico basin.

  3. Optimum load distribution between heat sources based on the Cournot model

    NASA Astrophysics Data System (ADS)

    Penkovskii, A. V.; Stennikov, V. A.; Khamisov, O. V.

    2015-08-01

    One of the widespread models of the heat supply of consumers, which is represented in the "Single buyer" format, is considered. The methodological base proposed for its description and investigation presents the use of principles of the theory of games, basic propositions of microeconomics, and models and methods of the theory of hydraulic circuits. The original mathematical model of the heat supply system operating under conditions of the "Single buyer" organizational structure provides the derivation of a solution satisfying the market Nash equilibrium. The distinctive feature of the developed mathematical model is that, along with problems solved traditionally within the bounds of bilateral relations of heat energy sources-heat consumer, it considers a network component with its inherent physicotechnical properties of the heat network and business factors connected with costs of the production and transportation of heat energy. This approach gives the possibility to determine optimum levels of load of heat energy sources. These levels provide the given heat energy demand of consumers subject to the maximum profit earning of heat energy sources and the fulfillment of conditions for formation of minimum heat network costs for a specified time. The practical realization of the search of market equilibrium is considered by the example of a heat supply system with two heat energy sources operating on integrated heat networks. The mathematical approach to the solution search is represented in the graphical form and illustrates computations based on the stepwise iteration procedure for optimization of levels of loading of heat energy sources (groping procedure by Cournot) with the corresponding computation of the heat energy price for consumers.

  4. Using cross correlations to calibrate lensing source redshift distributions: Improving cosmological constraints from upcoming weak lensing surveys

    SciTech Connect

    De Putter, Roland; Doré, Olivier; Das, Sudeep

    2014-01-10

    Cross correlations between the galaxy number density in a lensing source sample and that in an overlapping spectroscopic sample can in principle be used to calibrate the lensing source redshift distribution. In this paper, we study in detail to what extent this cross-correlation method can mitigate the loss of cosmological information in upcoming weak lensing surveys (combined with a cosmic microwave background prior) due to lack of knowledge of the source distribution. We consider a scenario where photometric redshifts are available and find that, unless the photometric redshift distribution p(z {sub ph}|z) is calibrated very accurately a priori (bias and scatter known to ∼0.002 for, e.g., EUCLID), the additional constraint on p(z {sub ph}|z) from the cross-correlation technique to a large extent restores the cosmological information originally lost due to the uncertainty in dn/dz(z). Considering only the gain in photo-z accuracy and not the additional cosmological information, enhancements of the dark energy figure of merit of up to a factor of four (40) can be achieved for a SuMIRe-like (EUCLID-like) combination of lensing and redshift surveys, where SuMIRe stands for Subaru Measurement of Images and Redshifts). However, the success of the method is strongly sensitive to our knowledge of the galaxy bias evolution in the source sample and we find that a percent level bias prior is needed to optimize the gains from the cross-correlation method (i.e., to approach the cosmology constraints attainable if the bias was known exactly).

  5. SELECTIVE SOURCE AC/DC POWER SUPPLY

    EPA Science Inventory

    This project will result in a prototype that will allow people and businesses to improve the efficiencies of photovoltaic products that they already own. The final prototype will be tested to quantify efficiency gain. This data will be analyzed to calculate the product’s pay...

  6. The influence of natural and anthropogenic secondary sources on the glyoxal global distribution

    NASA Astrophysics Data System (ADS)

    Myriokefalitakis, S.; Vrekoussis, M.; Tsigaridis, K.; Wittrock, F.; Richter, A.; Brühl, C.; Volkamer, R.; Burrows, J. P.; Kanakidou, M.

    2008-08-01

    Glyoxal, the smallest dicarbonyl, which has recently been observed from space, is expected to provide indications on volatile organic compounds (VOC) oxidation and secondary aerosol formation in the troposphere. Glyoxal (CHOCHO) is known to be mostly of natural origin and is produced during biogenic VOC oxidation. However, a number of anthropogenically emitted hydrocarbons, like acetylene and aromatics, have been positively identified as CHOCHO precursors. The present study investigates the contribution of pollution to the CHOCHO levels by taking into account the secondary chemical formation of CHOCHO from precursors emitted from biogenic, anthropogenic and biomass burning sources. The impact of potential primary land emissions of CHOCHO is also investigated. A global 3-dimensional chemistry transport model of the troposphere (TM4-ECPL) able to simulate the gas phase chemistry coupled with all major aerosol components is used. The secondary anthropogenic contribution from fossil fuel and industrial VOCs emissions oxidation to the CHOCHO columns is found to reach 20 70% in the industrialized areas of the Northern Hemisphere and 3 20% in the tropics. This secondary CHOCHO source is on average three times larger than that from oxidation of VOCs from biomass burning sources. The chemical production of CHOCHO is calculated to equal to about 56 Tg y-1 with 70% being produced from biogenic hydrocarbons oxidation, 17% from acetylene, 11% from aromatic chemistry and 2% from ethene and propene. CHOCHO is destroyed in the troposphere primarily by reaction with OH radicals (23%) and by photolysis (63%), but it is also removed from the atmosphere through wet (8%) and dry deposition (6%). Potential formation of secondary organic aerosol through CHOCHO losses on/in aerosols and clouds is neglected here due to the significant uncertainties associated with the underlying chemistry. The global annual mean CHOCHO burden and lifetime in the model domain are estimated to be 0.02 Tg

  7. Dc to ac converter operates efficiently at low input voltages

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Self-oscillating dc to ac converter with transistor switching to produce a square wave output is used for low and high voltage power sources. The converter has a high efficiency throughout a wide range of loads.

  8. Impact of routine episodic emissions on the expected frequency distribution of emissions from oil and gas production sources.

    NASA Astrophysics Data System (ADS)

    Smith, N.; Blewitt, D.; Hebert, L. B.

    2015-12-01

    In coordination with oil and gas operators, we developed a high resolution (< 1 min) simulation of temporal variability in well-pad oil and gas emissions over a year. We include routine emissions from condensate tanks, dehydrators, pneumatic devices, fugitive leaks and liquids unloading. We explore the variability in natural gas emissions from these individual well-pad sources, and find that routine short-term episodic emissions such as tank flashing and liquids unloading result in the appearance of a skewed, or 'fat-tail' distribution of emissions, from an individual well-pad over time. Additionally, we explore the expected variability in emissions from multiple wells with different raw gas composition, gas/liquids production volumes and control equipment. Differences in well-level composition, production volume and control equipment translate into differences in well-level emissions leading to a fat-tail distribution of emissions in the absence of operational upsets. Our results have several implications for recent studies focusing on emissions from oil and gas sources. Time scale of emission estimates are important and have important policy implications. Fat tail distributions may not be entirely driven by avoidable mechanical failures, and are expected to occur under routine operational conditions from short-duration emissions (e.g., tank flashing, liquid unloading). An understanding of the expected distribution of emissions for a particular population of wells is necessary to evaluate whether the observed distribution is more skewed than expected. Temporal variability in well-pad emissions make comparisons to annual average emissions inventories difficult and may complicate the interpretation of long-term ambient fenceline monitoring data. Sophisticated change detection algorithms will be necessary to identify when true operational upsets occur versus routine short-term emissions.

  9. Distribution of Acanthamoeba Genotypes Isolated from Recreational and Therapeutic Geothermal Water Sources in Southwestern Iran

    PubMed Central

    Niyyati, Maryam; Saberi, Reza; Latifi, Alireza; Lasjerdi, Zohreh

    2016-01-01

    A comprehensive survey was conducted along 10 km of geothermal rivers in southwestern Iran. A total of 40 water samples were tested for the presence of Acanthamoeba spp., and genotypes were determined by targeting the diagnostic fragment 3 region of the 18S rRNA gene. The pathogenic potential of all positive isolates was also identified using tolerance ability test. High occurrences of Acanthamoeba (50%) were detected in the sampling areas. Based on sequencing analysis, isolates belonging to T4 (93.7%) and T2 (6.25%) genotypes were reported. Thermo- and osmotolerance tests revealed that five strains are highly pathogenic. Since every collection site of this study was associated with high human activity, posting of warning signs, monitoring of recreational water sources, and awareness of high-risk people are of utmost importance. To the best of our knowledge, the present research is the first to report T2 genotype from geothermal water sources in Iran. PMID:27127409

  10. Distribution of Acanthamoeba Genotypes Isolated from Recreational and Therapeutic Geothermal Water Sources in Southwestern Iran.

    PubMed

    Niyyati, Maryam; Saberi, Reza; Latifi, Alireza; Lasjerdi, Zohreh

    2016-01-01

    A comprehensive survey was conducted along 10 km of geothermal rivers in southwestern Iran. A total of 40 water samples were tested for the presence of Acanthamoeba spp., and genotypes were determined by targeting the diagnostic fragment 3 region of the 18S rRNA gene. The pathogenic potential of all positive isolates was also identified using tolerance ability test. High occurrences of Acanthamoeba (50%) were detected in the sampling areas. Based on sequencing analysis, isolates belonging to T4 (93.7%) and T2 (6.25%) genotypes were reported. Thermo- and osmotolerance tests revealed that five strains are highly pathogenic. Since every collection site of this study was associated with high human activity, posting of warning signs, monitoring of recreational water sources, and awareness of high-risk people are of utmost importance. To the best of our knowledge, the present research is the first to report T2 genotype from geothermal water sources in Iran. PMID:27127409

  11. Measurements and modeling of impurity source distributions from the Tore Supra outboard pump limiter

    SciTech Connect

    Klepper, C.C.; Hogan, J.T.; Tobin, S.J.; Isler, R.C.; Guilhem, D.; Hess, W.R.; Monier-Garbet, P.

    1994-09-01

    An experiment has been carried out to study impurity generation processes on an inertial limiter on Tore Supra. It is part of a plan to assemble a more detailed integrated picture of impurity generation at the inner wall, the outboard and vertical pump limiters, and the heating and current drive antennas. A system has been implemented to permit quantitative measurement of impurity sources from the outboard limiter in Tore Supra. Data are presented for a representative case in which the limiter is isolated as much as possible from connection with other Tore Supra plasma-facing components. The data are compared with results from the Monte-Carlo SOL impurity transport code BBQ, in an attempt to identify the mechanism for impurity release. Evidence of chemical sputtering as an important impurity source is seen.

  12. Polycyclic aromatic hydrocarbons (PAHs) in the surficial sediments from Lake Iznik (Turkey): spatial distributions and sources.

    PubMed

    Unlü, Selma; Alpar, Bedri; Oztürk, Kurultay; Vardar, Denizhan

    2010-12-01

    The concentrations of 12 polycyclic aromatic hydrocarbons (PAHs) were determined from 28 sediment samples taken from the Lake Iznik located in the north-west area in Turkey. Total concentration of the PAHs was observed as in the range of 17-835 ng g⁻¹ dry weight, with the highest values recorded offshore the cities of Iznik and Orhangazi, and the Sölöz creek. According to the molecular indices, contamination of the PAHs in the lake was a mixture of the atmospheric input of high temperature pyrolytic processes and the petrogenic sources transported by the creeks. Further, the higher proportion of high molecular-weight PAHs (> 85%) suggests the domination of combustion-related sources. Compared to the consensus-based sediment quality guidelines for PAHs, there are no harmful biological effects on the short term to aquatic life. PMID:21069284

  13. SEI power source alternatives for rovers and other multi-kWe distributed surface applications

    NASA Technical Reports Server (NTRS)

    Bents, D. J.; Kohout, Lisa L.; Mckissock, B. I.; Rodriguez, C. D.; Withrow, C. A.; Colozza, A.; Hanlon, J. C.; Schmitz, P. C.

    1991-01-01

    Results of the study performed to support the Space Exploration Initiative (SEI) which investigated power system alternatives for the rover vehicles and servicers that would be used for construction and operation of a lunar base is described. Using the mission requirements and power profiles that were subsequently generated for each of these rovers and servicers, candidate power sources incorporating various power generation and energy storage technologies were identified. The technologies were those believed most appropriate to the SEI missions, and included solar, electrochemical, and isotope systems. The candidates were characterized with respect to system mass, deployed area and volume. For each of the missions a preliminary selection was made. Results of this study depict the available power sources in light of the mission requirements as they are currently defined.

  14. Tevatron AC dipole system

    SciTech Connect

    Miyamoto, R.; Kopp, S.E.; Jansson, A.; Syphers, M.J.; /Fermilab

    2007-06-01

    The AC dipole is an oscillating dipole magnet which can induce large amplitude oscillations without the emittance growth and decoherence. These properties make it a good tool to measure optics of a hadron synchrotron. The vertical AC dipole for the Tevatron is powered by an inexpensive high power audio amplifier since its operating frequency is approximately 20 kHz. The magnet is incorporated into a parallel resonant system to maximize the current. The use of a vertical pinger magnet which has been installed in the Tevatron made the cost relatively inexpensive. Recently, the initial system was upgraded with a more powerful amplifier and oscillation amplitudes up to 2-3{sigma} were achieved with the 980 GeV proton beam. This paper discusses details of the Tevatron AC dipole system and also shows its test results.

  15. An application of a zero-inflated lifetime distribution with multiple and incomplete data sources

    DOE PAGESBeta

    Hamada, M. S.; Margevicius, K. J.

    2016-02-11

    In this study, we analyze data sampled from a population of parts in which an associated anomaly can occur at assembly or after assembly. Using a zero-inflated lifetime distribution to fit left-censored and right-censored data as well data from a supplementary sample, we make predictions about the proportion of the population with anomalies today and in the future. Goodness-of-fit is also addressed.

  16. Distribution and sources of hydrocarbons in surface sediments of Gemlik Bay (Marmara Sea, Turkey).

    PubMed

    Unlü, Selma; Alpar, Bedri

    2006-07-01

    Seabottom sediments from Gemlik Bay, one of the most polluted spots in SW Marmara Sea, were analyzed for parent polycyclic aromatic hydrocarbons (PAHs) using gas chromatography-mass spectrometry. The concentration of 14 PAH compounds in sediment samples collected from 61 locations are distributed in a broad spectrum from low to very high concentration levels (50.8-13482 ng g-1). No significant correlation was found between summation operatorPAHs and organic carbon content while summation operatorPAHs increase slightly with silt/clay ratio. Therefore the distribution and concentrations of PAHs would be determined more by direct input, rather than by the type of sediment found locally. The most polluted areas are distributed nearshore eastern (Gemlik) and southern (Kursunlu, Mudanya and Trilye) coasts which are mainly influenced by rapid ecotourism development, direct discharges from rivers, surface run-off and drainage from port areas, domestic and industrial effluent discharges through outfalls and various contaminants from ships. Special PAH compound ratios, such as Phe/Anth, Flu/Py, B[a]A/Chry; LMWPAH/HMWPAH; Per/; Per/summation operatorPAH; Per/summation operator(penta-aromatics) and Flu/(Py+Flu), were calculated to evaluate different hydrocarbon origins and their relative importance. Pyrolytic activity is dominant along the highly-populated eastern and southern coasts. Meanwhile, petrogenic activity mixed with pyrolytic activity is a matter of fact in front of the main industrial-tourism ports and anchoring areas as well. Higher concentration of perylene are distributed along the mostly polluted eastern and southern coastal areas, however, the concentrations of perylene relative to the penta-aromatic isomers are dominant especially in the northern and deepest sectors of the bay, indicating diagenetic origin for the presence of perylene. PMID:16376968

  17. Stratigraphic controls on the source rock distribution, Llanos Orientales Basin, Colombia

    SciTech Connect

    Ramon, J.C.; Fajardo, A.; Rubiano, J.; Reyes, A. )

    1996-01-01

    All available rock and oil geochemistry analyses were tied to a high-resolution stratigraphic framework for more than 50 wells in the Central Llanos Orientates Basin. New Tertiary generation input is proposed. The best source rock intervals are at the base and top of the Gacheta Formation (Upper Cretaceous) and in the middle of the Barco-Cuervos (Paleocene) and Mirador (Eocene) formations. These organic-rich zones contain type II and III kerogen. TOC contents range from about 1% up to 15%. The four source rock intervals occur within marine shales near condensed sections, at the position maximum accommodation/sediment-supply (A/S) ratios. The development of conditions that allow accumulation and preservation of anomalously high fractions of organic matter might be explained by two mechanisms. Increased A/S ratio results in retention of more sediment in the coastal plain, thus reducing the tendency for siliciclastic sediment to dilute the organic matter accumulating on the shelf. Also, deeper water might restrict circulation, enhancing bottom anoxic conditions. In the more transitional and continental sequences, increased A/S ratio is associated with higher phreatic water level. A high ground water table enhances preservation of coaly intervals. The sea-level rise brings marine water into valleys and low-gradient coastal plains. The resulting embayments, marsh and swampy areas are organic-prone, contributing to the source rock potential of strata associated with high conditions and base-level rise-to-fall turnaround positions.

  18. [Altitudinal Gradient Distribution and Source Analysis of PAHs Content of Topsoil in Jinfo Mountain, Chongqing].

    PubMed

    Shi, Yang; Sun, Yu-chuan; Liang, Zuo-bing; Ren, Kun; Yuan, Dao-xian

    2015-04-01

    The condensation effect has made high mountains the storage vault of durable organic pollutants. This research measured the content and constitutes of polycyclic aromatic hydrocarbons (PAHs) in 10 topsoil samples collected at different altitudes from the south slope of Chongqing Jinfo Mountain by gas chromatograph-mass spectrometer (GC/MC). And the pollution source of PAHs was analyzed by ratio method and principal component regression. The ecological risk of PAHs was evaluated using BaP toxic equivlants (TEQ(BaP)) The results showed that the concentrations of 16 priority PAHs in topsoil ranged from 240-2 121 ng x g(-1). The average value of PAHs was 849 ng x g(-1), and 2 to 3-ring PAHs were the dominant compounds. The concentrations of 7 carcinogenic PAHs accounted for 17.8% of total PAHs averagely. In the research area, various-ring PAHs and gross PAHs increased with the rise of altitude. The increase of low-ring PAHs was most obvious, and the volatility of high-ring PAHs was relatively high. But the ratio of different-ring PAHs in gross PAHs showed no regularity with the rise of altitude. The PAHs of soil in the research area mainly came from the oil sources, oil products, and combustion sources of coal and biomass. In the research area, the soil has been polluted to a certain extent, but the toxicity risk is relatively low. PMID:26164921

  19. Spatial distribution and source apportionment of PFASs in surface sediments from five lake regions, China.

    PubMed

    Qi, Yanjie; Huo, Shouliang; Xi, Beidou; Hu, Shibin; Zhang, Jingtian; He, Zhuoshi

    2016-01-01

    Perfluoroalkyl substances (PFASs) have been found in environment globally. However, studies on PFAS occurrence in sediments of lakes or reservoirs remain relatively scarce. In this study, two hundred and sixty-two surface sediment samples were collected from forty-eight lakes and two reservoirs all over China. Average PFAS concentrations in surface sediments from each lake or reservoir varied from 0.086 ng/g dw to 5.79 ng/g dw with an average of 1.15 ng/g dw. Among five lake regions, average PFAS concentrations for the lakes from Eastern Plain Region were the highest. Perfluorooctanoic acid, perfluoroundecanoic acid and perfluorooctane sulfonic acid (PFOS) were the predominant PFASs in surface sediments. The significant positive correlations between PFAS concentrations and total organic carbon, total nitrogen and total phosphorus contents in sediments revealed the influences of sedimentary characteristics on PFAS occurrence. A two-dimensional hierarchical cluster analysis heat map was depicted to analyze the possible origins of sediments and individual PFAS. The food-packaging, textile, electroplating, firefighting and semiconductor industry emission sources and the precious metals and coating industry emission sources were identified as the main sources by two receptor models, with contributions of 77.7 and 22.3% to the total concentrations of C4-C14- perfluoroalkyl carboxylic acids and PFOS, respectively. PMID:26947748

  20. Spatial distribution and source apportionment of PFASs in surface sediments from five lake regions, China

    PubMed Central

    Qi, Yanjie; Huo, Shouliang; Xi, Beidou; Hu, Shibin; Zhang, Jingtian; He, Zhuoshi

    2016-01-01

    Perfluoroalkyl substances (PFASs) have been found in environment globally. However, studies on PFAS occurrence in sediments of lakes or reservoirs remain relatively scarce. In this study, two hundred and sixty-two surface sediment samples were collected from forty-eight lakes and two reservoirs all over China. Average PFAS concentrations in surface sediments from each lake or reservoir varied from 0.086 ng/g dw to 5.79 ng/g dw with an average of 1.15 ng/g dw. Among five lake regions, average PFAS concentrations for the lakes from Eastern Plain Region were the highest. Perfluorooctanoic acid, perfluoroundecanoic acid and perfluorooctane sulfonic acid (PFOS) were the predominant PFASs in surface sediments. The significant positive correlations between PFAS concentrations and total organic carbon, total nitrogen and total phosphorus contents in sediments revealed the influences of sedimentary characteristics on PFAS occurrence. A two-dimensional hierarchical cluster analysis heat map was depicted to analyze the possible origins of sediments and individual PFAS. The food-packaging, textile, electroplating, firefighting and semiconductor industry emission sources and the precious metals and coating industry emission sources were identified as the main sources by two receptor models, with contributions of 77.7 and 22.3% to the total concentrations of C4-C14- perfluoroalkyl carboxylic acids and PFOS, respectively. PMID:26947748