Preliminary Analysis of Aircraft Loss of Control Accidents: Worst Case Precursor Combinations and Temporal Sequencing

NASA Technical Reports Server (NTRS)

Belcastro, Christine M.; Groff, Loren; Newman, Richard L.; Foster, John V.; Crider, Dennis H.; Klyde, David H.; Huston, A. McCall

2014-01-01

Aircraft loss of control (LOC) is a leading cause of fatal accidents across all transport airplane and operational classes, and can result from a wide spectrum of hazards, often occurring in combination. Technologies developed for LOC prevention and recovery must therefore be effective under a wide variety of conditions and uncertainties, including multiple hazards, and their validation must provide a means of assessing system effectiveness and coverage of these hazards. This requires the definition of a comprehensive set of LOC test scenarios based on accident and incident data as well as future risks. This paper defines a comprehensive set of accidents and incidents over a recent 15 year period, and presents preliminary analysis results to identify worst-case combinations of causal and contributing factors (i.e., accident precursors) and how they sequence in time. Such analyses can provide insight in developing effective solutions for LOC, and form the basis for developing test scenarios that can be used in evaluating them. Preliminary findings based on the results of this paper indicate that system failures or malfunctions, crew actions or inactions, vehicle impairment conditions, and vehicle upsets contributed the most to accidents and fatalities, followed by inclement weather or atmospheric disturbances and poor visibility. Follow-on research will include finalizing the analysis through a team consensus process, defining future risks, and developing a comprehensive set of test scenarios with correlation to the accidents, incidents, and future risks. Since enhanced engineering simulations are required for batch and piloted evaluations under realistic LOC precursor conditions, these test scenarios can also serve as a high-level requirement for defining the engineering simulation enhancements needed for generating them.

Application of forensic image analysis in accident investigations.

PubMed

Verolme, Ellen; Mieremet, Arjan

2017-09-01

Forensic investigations are primarily meant to obtain objective answers that can be used for criminal prosecution. Accident analyses are usually performed to learn from incidents and to prevent similar events from occurring in the future. Although the primary goal may be different, the steps in which information is gathered, interpreted and weighed are similar in both types of investigations, implying that forensic techniques can be of use in accident investigations as well. The use in accident investigations usually means that more information can be obtained from the available information than when used in criminal investigations, since the latter require a higher evidence level. In this paper, we demonstrate the applicability of forensic techniques for accident investigations by presenting a number of cases from one specific field of expertise: image analysis. With the rapid spread of digital devices and new media, a wealth of image material and other digital information has become available for accident investigators. We show that much information can be distilled from footage by using forensic image analysis techniques. These applications show that image analysis provides information that is crucial for obtaining the sequence of events and the two- and three-dimensional geometry of an accident. Since accident investigation focuses primarily on learning from accidents and prevention of future accidents, and less on the blame that is crucial for criminal investigations, the field of application of these forensic tools may be broader than would be the case in purely legal sense. This is an important notion for future accident investigations. Copyright © 2017 Elsevier B.V. All rights reserved.

BNL severe-accident sequence experiments and analysis program. [PWR; BWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greene, G.A.; Ginsberg, T.; Tutu, N.K.

1983-01-01

In the analysis of degraded core accidents, the two major sources of pressure loading on light water reactor containments are: steam generation from core debris-water thermal interactions; and molten core-concrete interactions. Experiments are in progress at BNL in support of analytical model development related to aspects of the above containment loading mechanisms. The work supports development and evaluation of the CORCON (Muir, 1981) and MARCH (Wooton, 1980) computer codes. Progress in the two programs is described.

United States Department of Energy severe accident research following the Fukushima Daiichi accidents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, M. T.; Corradini, M.; Rempe, J.

The U.S. Department of Energy (DOE) has played a major role in the U.S. response to the events at Fukushima Daiichi. During the first several weeks following the accident, U.S. assistance efforts were guided by results from a significant and diverse set of analyses. In the months that followed, a coordinated analysis activity aimed at gaining a more thorough understanding of the accident sequence was completed using laboratory-developed, system-level best-estimate accident analysis codes, while a parallel analysis was conducted by U.S. industry. A comparison of predictions for Unit 1 from these two studies indicated significant differences between MAAP and MELCORmore » results for key plant parameters, such as in-core hydrogen production. On that basis, a crosswalk was completed to determine the key modeling variations that led to these differences. In parallel with these activities, it became clear that there was a need to perform a technology gap evaluation on accident-tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist given the current state of light water reactor (LWR) severe accident research and augmented by insights from Fukushima. In addition, there is growing international recognition that data from Fukushima could significantly reduce uncertainties related to severe accident progression, particularly for boiling water reactors. On these bases, a group of U. S. experts in LWR safety and plant operations was convened by the DOE Office of Nuclear Energy (DOE-NE) to complete technology gap analysis and Fukushima forensics data needs identification activities. The results from these activities were used as the basis for refining DOE-NE's severe accident research and development (R&D) plan. Finally, this paper provides a high-level review of DOE-sponsored R&D efforts in these areas, including planned activities on accident-tolerant components and accident analysis methods.« less

United States Department of Energy severe accident research following the Fukushima Daiichi accidents

DOE PAGES

Farmer, M. T.; Corradini, M.; Rempe, J.; ...

2016-11-02

The U.S. Department of Energy (DOE) has played a major role in the U.S. response to the events at Fukushima Daiichi. During the first several weeks following the accident, U.S. assistance efforts were guided by results from a significant and diverse set of analyses. In the months that followed, a coordinated analysis activity aimed at gaining a more thorough understanding of the accident sequence was completed using laboratory-developed, system-level best-estimate accident analysis codes, while a parallel analysis was conducted by U.S. industry. A comparison of predictions for Unit 1 from these two studies indicated significant differences between MAAP and MELCORmore » results for key plant parameters, such as in-core hydrogen production. On that basis, a crosswalk was completed to determine the key modeling variations that led to these differences. In parallel with these activities, it became clear that there was a need to perform a technology gap evaluation on accident-tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist given the current state of light water reactor (LWR) severe accident research and augmented by insights from Fukushima. In addition, there is growing international recognition that data from Fukushima could significantly reduce uncertainties related to severe accident progression, particularly for boiling water reactors. On these bases, a group of U. S. experts in LWR safety and plant operations was convened by the DOE Office of Nuclear Energy (DOE-NE) to complete technology gap analysis and Fukushima forensics data needs identification activities. The results from these activities were used as the basis for refining DOE-NE's severe accident research and development (R&D) plan. Finally, this paper provides a high-level review of DOE-sponsored R&D efforts in these areas, including planned activities on accident-tolerant components and accident analysis methods.« less

Interim reliability-evaluation program: analysis of the Browns Ferry, Unit 1, nuclear plant. Appendix C - sequence quantification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mays, S.E.; Poloski, J.P.; Sullivan, W.H.

1982-07-01

This report describes a risk study of the Browns Ferry, Unit 1, nuclear plant. The study is one of four such studies sponsored by the NRC Office of Research, Division of Risk Assessment, as part of its Interim Reliability Evaluation Program (IREP), Phase II. This report is contained in four volumes: a main report and three appendixes. Appendix C generally describes the methods used to estimate accident sequence frequency values. Information is presented concerning the approach, example collection, failure data, candidate dominant sequences, uncertainty analysis, and sensitivity analysis.

Final safety analysis report for the Galileo Mission: Volume 2, Book 2: Accident model document: Appendices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-12-15

This section of the Accident Model Document (AMD) presents the appendices which describe the various analyses that have been conducted for use in the Galileo Final Safety Analysis Report II, Volume II. Included in these appendices are the approaches, techniques, conditions and assumptions used in the development of the analytical models plus the detailed results of the analyses. Also included in these appendices are summaries of the accidents and their associated probabilities and environment models taken from the Shuttle Data Book (NSTS-08116), plus summaries of the several segments of the recent GPHS safety test program. The information presented in thesemore » appendices is used in Section 3.0 of the AMD to develop the Failure/Abort Sequence Trees (FASTs) and to determine the fuel releases (source terms) resulting from the potential Space Shuttle/IUS accidents throughout the missions.« less

Analysis of unmitigated large break loss of coolant accidents using MELCOR code

NASA Astrophysics Data System (ADS)

Pescarini, M.; Mascari, F.; Mostacci, D.; De Rosa, F.; Lombardo, C.; Giannetti, F.

2017-11-01

In the framework of severe accident research activity developed by ENEA, a MELCOR nodalization of a generic Pressurized Water Reactor of 900 MWe has been developed. The aim of this paper is to present the analysis of MELCOR code calculations concerning two independent unmitigated large break loss of coolant accident transients, occurring in the cited type of reactor. In particular, the analysis and comparison between the transients initiated by an unmitigated double-ended cold leg rupture and an unmitigated double-ended hot leg rupture in the loop 1 of the primary cooling system is presented herein. This activity has been performed focusing specifically on the in-vessel phenomenology that characterizes this kind of accidents. The analysis of the thermal-hydraulic transient phenomena and the core degradation phenomena is therefore here presented. The analysis of the calculated data shows the capability of the code to reproduce the phenomena typical of these transients and permits their phenomenological study. A first sequence of main events is here presented and shows that the cold leg break transient results faster than the hot leg break transient because of the position of the break. Further analyses are in progress to quantitatively assess the results of the code nodalization for accident management strategy definition and fission product source term evaluation.

1994 Accident sequence precursor program results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belles, R.J.; Cletcher, J.W.; Copinger, D.A.

1996-01-01

The Accident Sequence Precursor (ASP) Program involves the systematic review and evaluation of operational events that have occurred at light-water reactors to identify and categorize precursors to potential severe core damage accident sequences. The results of the ASP Program are published in an annual report. The most recent report, which contains the analyses of the precursors for 1994, is NUREG/CR-4674, Vols. 21 and 22, Precursors to Potential Severe Core Damage Accidents: 1994, A Status Report, published in December 1995. This article provides an overview of the ASP review and evaluation process and a summary of the results for 1994. 12more » refs., 2 figs., 4 tabs.« less

Loss of DHR sequences at Browns Ferry Unit One - accident-sequence analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, D.H.; Grene, S.R.; Harrington, R.M.

1983-05-01

This study describes the predicted response of Unit One at the Browns Ferry Nuclear Plant to a postulated loss of decay heat removal (DHR) capability following scram from full power with the power conversion system unavailable. In accident sequences without DHR capability, the residual heat removal (RHR) system functions of pressure suppression pool cooling and reactor vessel shutdown cooling are unavailable. Consequently, all decay heat energy is stored in the pressure suppression pool with a concomitant increase in pool temperature and primary containment pressure. With the assumption that DHR capability is not regained during the lengthy course of this accidentmore » sequence, the containment ultimately fails by overpressurization. Although unlikely, this catastrophic failure might lead to loss of the ability to inject cooling water into the reactor vessel, causing subsequent core uncovery and meltdown. The timing of these events and the effective mitigating actions that might be taken by the operator are discussed in this report.« less

Probabilistic risk assessment for a loss of coolant accident in McMaster Nuclear Reactor and application of reliability physics model for modeling human reliability

NASA Astrophysics Data System (ADS)

Ha, Taesung

A probabilistic risk assessment (PRA) was conducted for a loss of coolant accident, (LOCA) in the McMaster Nuclear Reactor (MNR). A level 1 PRA was completed including event sequence modeling, system modeling, and quantification. To support the quantification of the accident sequence identified, data analysis using the Bayesian method and human reliability analysis (HRA) using the accident sequence evaluation procedure (ASEP) approach were performed. Since human performance in research reactors is significantly different from that in power reactors, a time-oriented HRA model (reliability physics model) was applied for the human error probability (HEP) estimation of the core relocation. This model is based on two competing random variables: phenomenological time and performance time. The response surface and direct Monte Carlo simulation with Latin Hypercube sampling were applied for estimating the phenomenological time, whereas the performance time was obtained from interviews with operators. An appropriate probability distribution for the phenomenological time was assigned by statistical goodness-of-fit tests. The human error probability (HEP) for the core relocation was estimated from these two competing quantities: phenomenological time and operators' performance time. The sensitivity of each probability distribution in human reliability estimation was investigated. In order to quantify the uncertainty in the predicted HEPs, a Bayesian approach was selected due to its capability of incorporating uncertainties in model itself and the parameters in that model. The HEP from the current time-oriented model was compared with that from the ASEP approach. Both results were used to evaluate the sensitivity of alternative huinan reliability modeling for the manual core relocation in the LOCA risk model. This exercise demonstrated the applicability of a reliability physics model supplemented with a. Bayesian approach for modeling human reliability and its potential usefulness of quantifying model uncertainty as sensitivity analysis in the PRA model.

Expert systems for fault diagnosis in nuclear reactor control

NASA Astrophysics Data System (ADS)

Jalel, N. A.; Nicholson, H.

1990-11-01

An expert system for accident analysis and fault diagnosis for the Loss Of Fluid Test (LOFT) reactor, a small scale pressurized water reactor, was developed for a personal computer. The knowledge of the system is presented using a production rule approach with a backward chaining inference engine. The data base of the system includes simulated dependent state variables of the LOFT reactor model. Another system is designed to assist the operator in choosing the appropriate cooling mode and to diagnose the fault in the selected cooling system. The response tree, which is used to provide the link between a list of very specific accident sequences and a set of generic emergency procedures which help the operator in monitoring system status, and to differentiate between different accident sequences and select the correct procedures, is used to build the system knowledge base. Both systems are written in TURBO PROLOG language and can be run on an IBM PC compatible with 640k RAM, 40 Mbyte hard disk and color graphics.

Deep Borehole Emplacement Mode Hazard Analysis Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sevougian, S. David

This letter report outlines a methodology and provides resource information for the Deep Borehole Emplacement Mode Hazard Analysis (DBEMHA). The main purpose is identify the accident hazards and accident event sequences associated with the two emplacement mode options (wireline or drillstring), to outline a methodology for computing accident probabilities and frequencies, and to point to available databases on the nature and frequency of accidents typically associated with standard borehole drilling and nuclear handling operations. Risk mitigation and prevention measures, which have been incorporated into the two emplacement designs (see Cochran and Hardin 2015), are also discussed. A key intent ofmore » this report is to provide background information to brief subject matter experts involved in the Emplacement Mode Design Study. [Note: Revision 0 of this report is concentrated more on the wireline emplacement mode. It is expected that Revision 1 will contain further development of the preliminary fault and event trees for the drill string emplacement mode.]« less

Injury protection and accident causation parameters for vulnerable road users based on German In-Depth Accident Study GIDAS.

PubMed

Otte, Dietmar; Jänsch, Michael; Haasper, Carl

2012-01-01

Within a study of accident data from GIDAS (German In-Depth Accident Study), vulnerable road users are investigated regarding injury risk in traffic accidents. GIDAS is the largest in-depth accident study in Germany. Due to a well-defined sampling plan, representativeness with respect to the federal statistics is also guaranteed. A hierarchical system ACASS (Accident Causation Analysis with Seven Steps) was developed in GIDAS, describing the human causation factors in a chronological sequence. The accordingly classified causation factors - derived from the systematic of the analysis of human accident causes ("7 steps") - can be used to describe the influence of accident causes on the injury outcome. The bases of the study are accident documentations over ten years from 1999 to 2008 with 8204 vulnerable road users (VRU), of which 3 different groups were selected as pedestrians n=2041, motorcyclists n=2199 and bicyclists n=3964, and analyzed on collisions with cars and trucks as well as vulnerable road users alone. The paper will give a description of the injury pattern and injury mechanisms of accidents. The injury frequencies and severities are pointed out considering different types of VRU and protective measures of helmet and clothes of the human body. The impact points are demonstrated on the car, following to conclusion of protective measures on the vehicle. Existing standards of protection devices as well as interdisciplinary research, including accident and injury statistics, are described. With this paper, a summarization of the existing possibilities on protective measures for pedestrians, bicyclists and motorcyclists is given and discussed by comparison of all three groups of vulnerable road users. Also the relevance of special impact situations and accident causes mainly responsible for severe injuries are pointed out, given the new orientation of research for the avoidance and reduction of accident patterns. 2010 Elsevier Ltd. All rights reserved.

Conceptual design study of Fusion Experimental Reactor (FY86 FER): Safety

NASA Astrophysics Data System (ADS)

Seki, Yasushi; Iida, Hiromasa; Honda, Tsutomu

1987-08-01

This report describes the study on safety for FER (Fusion Experimental Reactor) which has been designed as a next step machine to the JT-60. Though the final purpose of this study is to have an image of design base accident, maximum credible accident and to assess their risk or probability, etc., as FER plant system, the emphasis of this years study is placed on fuel-gas circulation system where the tritium inventory is maximum. The report consists of two chapters. The first chapter summarizes the FER system and describes FMEA (Failure Mode and Effect Analysis) and related accident progression sequence for FER plant system as a whole. The second chapter of this report is focused on fuel-gas circulation system including purification, isotope separation and storage. Probability of risk is assessed by the probabilistic risk analysis (PRA) procedure based on FMEA, ETA and FTA.

Station Blackout at Browns Ferry Unit One - accident sequence analysis. Volume 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, D.H.; Harrington, R.M.; Greene, S.R.

1981-11-01

This study describes the predicted response of Unit 1 at the Browns Ferry Nuclear Plant to Station Blackout, defined as a loss of offsite power combined with failure of all onsite emergency diesel-generators to start and load. Every effort has been made to employ the most realistic assumptions during the process of defining the sequence of events for this hypothetical accident. DC power is assumed to remain available from the unit batteries during the initial phase and the operator actions and corresponding events during this period are described using results provided by an analysis code developed specifically for this purpose.more » The Station Blackout is assumed to persist beyond the point of battery exhaustion and the events during this second phase of the accident in which dc power would be unavailable were determined through use of the MARCH code. Without dc power, cooling water could no longer be injected into the reactor vessel and the events of the second phase include core meltdown and subsequent containment failure. An estimate of the magnitude and timing of the concomitant release of the noble gas, cesium, and iodine-based fission products to the environment is provided in Volume 2 of this report. 58 refs., 75 figs., 8 tabs.« less

Interim Reliability Evaluation Program: analysis of the Browns Ferry, Unit 1, nuclear plant. Main report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mays, S.E.; Poloski, J.P.; Sullivan, W.H.

1982-07-01

A probabilistic risk assessment (PRA) was made of the Browns Ferry, Unit 1, nuclear plant as part of the Nuclear Regulatory Commission's Interim Reliability Evaluation Program (IREP). Specific goals of the study were to identify the dominant contributors to core melt, develop a foundation for more extensive use of PRA methods, expand the cadre of experienced PRA practitioners, and apply procedures for extension of IREP analyses to other domestic light water reactors. Event tree and fault tree analyses were used to estimate the frequency of accident sequences initiated by transients and loss of coolant accidents. External events such as floods,more » fires, earthquakes, and sabotage were beyond the scope of this study and were, therefore, excluded. From these sequences, the dominant contributors to probable core melt frequency were chosen. Uncertainty and sensitivity analyses were performed on these sequences to better understand the limitations associated with the estimated sequence frequencies. Dominant sequences were grouped according to common containment failure modes and corresponding release categories on the basis of comparison with analyses of similar designs rather than on the basis of detailed plant-specific calculations.« less

A variational technique for smoothing flight-test and accident data

NASA Technical Reports Server (NTRS)

Bach, R. E., Jr.

1980-01-01

The problem of determining aircraft motions along a trajectory is solved using a variational algorithm that generates unmeasured states and forcing functions, and estimates instrument bias and scale-factor errors. The problem is formulated as a nonlinear fixed-interval smoothing problem, and is solved as a sequence of linear two-point boundary value problems, using a sweep method. The algorithm has been implemented for use in flight-test and accident analysis. Aircraft motions are assumed to be governed by a six-degree-of-freedom kinematic model; forcing functions consist of body accelerations and winds, and the measurement model includes aerodynamic and radar data. Examples of the determination of aircraft motions from typical flight-test and accident data are presented.

Waste management facility accident analysis (WASTE ACC) system: software for analysis of waste management alternatives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kohout, E.F.; Folga, S.; Mueller, C.

1996-03-01

This paper describes the Waste Management Facility Accident Analysis (WASTE{underscore}ACC) software, which was developed at Argonne National Laboratory (ANL) to support the US Department of Energy`s (DOE`s) Waste Management (WM) Programmatic Environmental Impact Statement (PEIS). WASTE{underscore}ACC is a decision support and database system that is compatible with Microsoft{reg_sign} Windows{trademark}. It assesses potential atmospheric releases from accidents at waste management facilities. The software provides the user with an easy-to-use tool to determine the risk-dominant accident sequences for the many possible combinations of process technologies, waste and facility types, and alternative cases described in the WM PEIS. In addition, its structure willmore » allow additional alternative cases and assumptions to be tested as part of the future DOE programmatic decision-making process. The WASTE{underscore}ACC system demonstrates one approach to performing a generic, systemwide evaluation of accident risks at waste management facilities. The advantages of WASTE{underscore}ACC are threefold. First, the software gets waste volume and radiological profile data that were used to perform other WM PEIS-related analyses directly from the WASTE{underscore}MGMT system. Second, the system allows for a consistent analysis across all sites and waste streams, which enables decision makers to understand more fully the trade-offs among various policy options and scenarios. Third, the system is easy to operate; even complex scenario runs are completed within minutes.« less

R/S analysis of reaction time in Neuron Type Test for human activity in civil aviation

NASA Astrophysics Data System (ADS)

Zhang, Hong-Yan; Kang, Ming-Cui; Li, Jing-Qiang; Liu, Hai-Tao

2017-03-01

Human factors become the most serious problem leading to accidents of civil aviation, which stimulates the design and analysis of Neuron Type Test (NTT) system to explore the intrinsic properties and patterns behind the behaviors of professionals and students in civil aviation. In the experiment, normal practitioners' reaction time sequences, collected from NTT, exhibit log-normal distribution approximately. We apply the χ2 test to compute the goodness-of-fit by transforming the time sequence with Box-Cox transformation to cluster practitioners. The long-term correlation of different individual practitioner's time sequence is represented by the Hurst exponent via Rescaled Range Analysis, also named by Range/Standard deviation (R/S) Analysis. The different Hurst exponent suggests the existence of different collective behavior and different intrinsic patterns of human factors in civil aviation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muhlheim, M.D.; Belles, R.J.; Cletcher, J.W.

The Accident Sequence Precursor (ASP) Program involves the systematic review and evaluation of operational events that have occurred at light-water reactors to identify and categorize precursors to potential severe core damage accident sequences. The results of the ASP Program are published in an annual report. The most recent report, which contains the precursors for 1995, is NUREG/CR-4674, Volume 23, Precursors to Potential Severe Core Damage Accidents: 1995, A Status Report, published in April 1997. This article provides an overview of the ASP review and evaluation process and a summary of the results for 1995.

Investigating accident causation through information network modelling.

PubMed

Griffin, T G C; Young, M S; Stanton, N A

2010-02-01

Management of risk in complex domains such as aviation relies heavily on post-event investigations, requiring complex approaches to fully understand the integration of multi-causal, multi-agent and multi-linear accident sequences. The Event Analysis of Systemic Teamwork methodology (EAST; Stanton et al. 2008) offers such an approach based on network models. In this paper, we apply EAST to a well-known aviation accident case study, highlighting communication between agents as a central theme and investigating the potential for finding agents who were key to the accident. Ultimately, this work aims to develop a new model based on distributed situation awareness (DSA) to demonstrate that the risk inherent in a complex system is dependent on the information flowing within it. By identifying key agents and information elements, we can propose proactive design strategies to optimize the flow of information and help work towards avoiding aviation accidents. Statement of Relevance: This paper introduces a novel application of an holistic methodology for understanding aviation accidents. Furthermore, it introduces an ongoing project developing a nonlinear and prospective method that centralises distributed situation awareness and communication as themes. The relevance of findings are discussed in the context of current ergonomic and aviation issues of design, training and human-system interaction.

Assessment of an explosive LPG release accident: a case study.

PubMed

Bubbico, Roberto; Marchini, Mauro

2008-07-15

In the present paper, an accident occurred during a liquefied petroleum gas (LPG) tank filling activity has been taken into consideration. During the transfer of LPG from the source road tank car to the receiving fixed storage vessel, an accidental release of LPG gave rise to different final consequences ranging from a pool fire, to a fireball and to the catastrophic rupture of the tank with successive explosion of its contents. The sequence of events has been investigated by using some of the consequence calculation models most commonly adopted in risk analysis and accident investigation. On one hand, this allows to better understand the link between the various events of the accident. On the other hand, a comparison between the results of the calculations and the damages actually observed after the accident, allows to check the accuracy of the prediction models and to critically assess their validity. In particular, it was shown that the largest uncertainty is associated with the calculation of the energy involved in the physical expansion of the fluid (both liquid and vapor) after the catastrophic rupture of the tank.

Nuclear Power Plant Cyber Security Discrete Dynamic Event Tree Analysis (LDRD 17-0958) FY17 Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wheeler, Timothy A.; Denman, Matthew R.; Williams, R. A.

Instrumentation and control of nuclear power is transforming from analog to modern digital assets. These control systems perform key safety and security functions. This transformation is occurring in new plant designs as well as in the existing fleet of plants as the operation of those plants is extended to 60 years. This transformation introduces new and unknown issues involving both digital asset induced safety issues and security issues. Traditional nuclear power risk assessment tools and cyber security assessment methods have not been modified or developed to address the unique nature of cyber failure modes and of cyber security threat vulnerabilities.more » iii This Lab-Directed Research and Development project has developed a dynamic cyber-risk in- formed tool to facilitate the analysis of unique cyber failure modes and the time sequencing of cyber faults, both malicious and non-malicious, and impose those cyber exploits and cyber faults onto a nuclear power plant accident sequence simulator code to assess how cyber exploits and cyber faults could interact with a plants digital instrumentation and control (DI&C) system and defeat or circumvent a plants cyber security controls. This was achieved by coupling an existing Sandia National Laboratories nuclear accident dynamic simulator code with a cyber emulytics code to demonstrate real-time simulation of cyber exploits and their impact on automatic DI&C responses. Studying such potential time-sequenced cyber-attacks and their risks (i.e., the associated impact and the associated degree of difficulty to achieve the attack vector) on accident management establishes a technical risk informed framework for developing effective cyber security controls for nuclear power.« less

A Multiplex PCR assay to differentiate between dog and red fox.

PubMed

Weissenberger, M; Reichert, W; Mattern, R

2011-11-01

Foxes are frequently the cause of car accidents in Baden-Württemberg (BW, Germany). The domestic dog (Canis familiaris) is in close relation to the red fox (Vulpes vulpes) and the silver fox which is a coat colour variant of the red fox. As insurance claims that involve accidents with animals require authentication, we analyzed frequency distribution and allele sizes in two canine microsatellite loci in 26 dogs (different breeds) and 19 red foxes of the region of BW, Germany. Moreover, sequencing analysis was performed. Red foxes exhibited only 1 allele at each microsatellite locus, whereas in dog 7 alleles at the CPH4 locus and 6 alleles at the CPH12 locus were detected. Sequences of PCR products from the two species revealed several differences between dogs and foxes. We established a sequenced allelic ladder and give population data from dogs and red foxes from the region of BW, Germany. Using microsatellite polymorphisms is efficient in differentiating between dogs and foxes in forensic casework. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

The Viareggio LPG railway accident: event reconstruction and modeling.

PubMed

Brambilla, Sara; Manca, Davide

2010-10-15

This manuscript describes in detail the LPG accident occurred in Viareggio on June 2009 and its modeling. The accident investigation highlighted the uncertainty and complexity of assessing and modeling what happened in the congested environment close to the Viareggio railway station. Nonetheless, the analysis allowed comprehending the sequence of events, the way they influenced each other, and the different possible paths/evolutions. The paper describes suitable models for the quantitative assessment of the consequences of the most probable accidental dynamics and its outcomes. The main finding is that after about 80 s from the beginning of the release the dense-gas cloud reached the surrounding houses that were destroyed successively by internal explosions. This fact has two main implications. First, it shows that the adopted modeling framework can give a correct picture of what happened in Viareggio. Second, it confirms the need to develop effective mitigation measures because, in case of this kind of accidents, there is no time to apply any protective emergency plans/actions. 2010 Elsevier B.V. All rights reserved.

Accident sequence precursor events with age-related contributors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, G.A.; Kohn, W.E.

1995-12-31

The Accident Sequence Precursor (ASP) Program at ORNL analyzed about 14.000 Licensee Event Reports (LERs) filed by US nuclear power plants 1987--1993. There were 193 events identified as precursors to potential severe core accident sequences. These are reported in G/CR-4674. Volumes 7 through 20. Under the NRC Nuclear Plant Aging Research program, the authors evaluated these events to determine the extent to which component aging played a role. Events were selected that involved age-related equipment degradation that initiated an event or contributed to an event sequence. For the 7-year period, ORNL identified 36 events that involved aging degradation as amore » contributor to an ASP event. Except for 1992, the percentage of age-related events within the total number of ASP events over the 7-year period ({approximately}19%) appears fairly consistent up to 1991. No correlation between plant ape and number of precursor events was found. A summary list of the age-related events is presented in the report.« less

WHEN MODEL MEETS REALITY – A REVIEW OF SPAR LEVEL 2 MODEL AGAINST FUKUSHIMA ACCIDENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhegang Ma

The Standardized Plant Analysis Risk (SPAR) models are a set of probabilistic risk assessment (PRA) models used by the Nuclear Regulatory Commission (NRC) to evaluate the risk of operations at U.S. nuclear power plants and provide inputs to risk informed regulatory process. A small number of SPAR Level 2 models have been developed mostly for feasibility study purpose. They extend the Level 1 models to include containment systems, group plant damage states, and model containment phenomenology and accident progression in containment event trees. A severe earthquake and tsunami hit the eastern coast of Japan in March 2011 and caused significantmore » damages on the reactors in Fukushima Daiichi site. Station blackout (SBO), core damage, containment damage, hydrogen explosion, and intensive radioactivity release, which have been previous analyzed and assumed as postulated accident progression in PRA models, now occurred with various degrees in the multi-units Fukushima Daiichi site. This paper reviews and compares a typical BWR SPAR Level 2 model with the “real” accident progressions and sequences occurred in Fukushima Daiichi Units 1, 2, and 3. It shows that the SPAR Level 2 model is a robust PRA model that could very reasonably describe the accident progression for a real and complicated nuclear accident in the world. On the other hand, the comparison shows that the SPAR model could be enhanced by incorporating some accident characteristics for better representation of severe accident progression.« less

Manned space flight nuclear system safety. Volume 3: Reactor system preliminary nuclear safety analysis. Part 2A: Accident model document, appendix

NASA Technical Reports Server (NTRS)

1972-01-01

The detailed abort sequence trees for the reference zirconium hydride (ZrH) reactor power module that have been generated for each phase of the reference Space Base program mission are presented. The trees are graphical representations of causal sequences. Each tree begins with the phase identification and the dichotomy between success and failure. The success branch shows the mission phase objective as being achieved. The failure branch is subdivided, as conditions require, into various primary initiating abort conditions.

Low-Probability High-Consequence (LPHC) Failure Events in Geologic Carbon Sequestration Pipelines and Wells: Framework for LPHC Risk Assessment Incorporating Spatial Variability of Risk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oldenburg, Curtis M.; Budnitz, Robert J.

If Carbon dioxide Capture and Storage (CCS) is to be effective in mitigating climate change, it will need to be carried out on a very large scale. This will involve many thousands of miles of dedicated high-pressure pipelines in order to transport many millions of tonnes of CO 2 annually, with the CO 2 delivered to many thousands of wells that will inject the CO 2 underground. The new CCS infrastructure could rival in size the current U.S. upstream natural gas pipeline and well infrastructure. This new infrastructure entails hazards for life, health, animals, the environment, and natural resources. Pipelinesmore » are known to rupture due to corrosion, from external forces such as impacts by vehicles or digging equipment, by defects in construction, or from the failure of valves and seals. Similarly, wells are vulnerable to catastrophic failure due to corrosion, cement degradation, or operational mistakes. While most accidents involving pipelines and wells will be minor, there is the inevitable possibility of accidents with very high consequences, especially to public health. The most important consequence of concern is CO 2 release to the environment in concentrations sufficient to cause death by asphyxiation to nearby populations. Such accidents are thought to be very unlikely, but of course they cannot be excluded, even if major engineering effort is devoted (as it will be) to keeping their probability low and their consequences minimized. This project has developed a methodology for analyzing the risks of these rare but high-consequence accidents, using a step-by-step probabilistic methodology. A key difference between risks for pipelines and wells is that the former are spatially distributed along the pipe whereas the latter are confined to the vicinity of the well. Otherwise, the methodology we develop for risk assessment of pipeline and well failures is similar and provides an analysis both of the annual probabilities of accident sequences of concern and of their consequences, and crucially the methodology provides insights into what measures might be taken to mitigate those accident sequences identified as of concern. Mitigating strategies could address reducing the likelihood of an accident sequence of concern, or reducing the consequences, or some combination. The methodology elucidates both local and integrated risks along the pipeline or at the well providing information useful to decision makers at various levels including local (e.g., property owners and town councils), regional (e.g., county and state representatives), and national levels (federal regulators and corporate proponents).« less

Unlocking the Mystery of Columbia's Tragic Accident Through Materials Characterization

NASA Technical Reports Server (NTRS)

Shah, Sandeep; Jerman, Gregory; Coston, James

2003-01-01

The wing and underbelly reconstruction of Space Shuttle Columbia took place at the Shuttle Landing Facility Hangar after the accident which destroyed STS-107. Fragments were placed on a grid according to their original location on the orbiter. Some Reinforced Carbon-Carbon (RCC) panels of the left wing leading edge and other parts from both leading edges were recovered and incorporated into the reconstruction. The recovered parts were tracked on a database according to a number and also tracked on a map of the orbiter. This viewgraph presentation describes the process of failure analysis undertaken by the Materials and Processes (M&P) Problem Resolution Team. The team started with factual observations about the accident, and identified highest level questions for it to answer in order to understand where on the orbiter failure occured, what component(s) failed, and what was the sequence of events. The finding of Columbia's MADS/OEX data recorder shifted the focus of the team's analysis to the left wing leading edge damage. The team placed particular attention on slag deposits on some of the RCC panels. The presentation lists analysis techniques, and lower level questions for the team to answer.

Anesthesia patient risk: a quantitative approach to organizational factors and risk management options.

PubMed

Paté-Cornell, M E; Lakats, L M; Murphy, D M; Gaba, D M

1997-08-01

The risk of death or brain damage to anesthesia patients is relatively low, particularly for healthy patients in modern hospitals. When an accident does occur, its cause is usually an error made by the anesthesiologist, either in triggering the accident sequence, or failing to take timely corrective measures. This paper presents a pilot study which explores the feasibility of extending probabilistic risk analysis (PRA) of anesthesia accidents to assess the effects of human and management components on the patient risk. We develop first a classic PRA model for the patient risk per operation. We then link the probabilities of the different accident types to their root causes using a probabilistic analysis of the performance shaping factors. These factors are described here as the "state of the anesthesiologist" characterized both in terms of alertness and competence. We then analyze the effects of different management factors that affect the state of the anesthesiologist and we compute the risk reduction benefits of several risk management policies. Our data sources include the published version of the Australian Incident Monitoring Study as well as expert opinions. We conclude that patient risk could be reduced substantially by closer supervision of residents, the use of anesthesia simulators both in training and for periodic recertification, and regular medical examinations for all anesthesiologists.

Station blackout transient at the Browns Ferry Unit 1 Plant: a severe accident sequence analysis (SASA) program study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz, R.R.

1982-01-01

Operating plant transients are of great interest for many reasons, not the least of which is the potential for a mild transient to degenerate to a severe transient yielding core damage. Using the Browns Ferry (BF) Unit-1 plant as a basis of study, the station blackout sequence was investigated by the Severe Accident Sequence Analysis (SASA) Program in support of the Nuclear Regulatory Commission's Unresolved Safety Issue A-44: Station Blackout. A station blackout transient occurs when the plant's AC power from a comemrcial power grid is lost and cannot be restored by the diesel generators. Under normal operating conditions, fmore » a loss of offsite power (LOSP) occurs (i.e., a complete severance of the BF plants from the Tennessee Valley Authority (TVA) power grid), the eight diesel generators at the three BF units would quickly start and power the emergency AC buses. Of the eight diesel generators, only six are needed to safely shut down all three units. Examination of BF-specific data show that LOSP frequency is low at Unit 1. The station blackout frequency is even lower (5.7 x 10/sup -4/ events per year) and hinges on whether the diesel generators start. The frequency of diesel generator failure is dictated in large measure by the emergency equipment cooling water (EECW) system that cools the diesel generators.« less

MARTINS: A foam/film flow model for molten material relocation in HWRs with U-Al-fueled multi-tube assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalimullah

1994-03-01

Some special purpose heavy-water reactors (EM) are made of assemblies consisting of a number of coaxial aluminum-clad U-Al alloy fuel tubes and an outer Al sleeve surrounding the fuel tubes. The heavy water coolant flows in the annular gaps between the circular tubes. Analysis of severe accidents in such reactors requires a model for predicting the behavior of the fuel tubes as they melt and disrupt. This paper describes a detailed, mechanistic model for fuel tube heatup, melting, freezing, and molten material relocation, called MARTINS (Melting and Relocation of Tubes in Nuclear subassembly). The paper presents the modeling of themore » phenomena in MARTINS, and an application of the model to analysis of a reactivity insertion accident. Some models are being developed to compute gradual downward relocation of molten material at decay-heat power levels via candling along intact tubes, neglecting coolant vapor hydrodynamic forces on molten material. These models are inadequate for high power accident sequences involving significant hydrodynamic forces. These forces are included in MARTINS.« less

Application of MELCOR Code to a French PWR 900 MWe Severe Accident Sequence and Evaluation of Models Performance Focusing on In-Vessel Thermal Hydraulic Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Rosa, Felice

2006-07-01

In the ambit of the Severe Accident Network of Excellence Project (SARNET), funded by the European Union, 6. FISA (Fission Safety) Programme, one of the main tasks is the development and validation of the European Accident Source Term Evaluation Code (ASTEC Code). One of the reference codes used to compare ASTEC results, coming from experimental and Reactor Plant applications, is MELCOR. ENEA is a SARNET member and also an ASTEC and MELCOR user. During the first 18 months of this project, we performed a series of MELCOR and ASTEC calculations referring to a French PWR 900 MWe and to themore » accident sequence of 'Loss of Steam Generator (SG) Feedwater' (known as H2 sequence in the French classification). H2 is an accident sequence substantially equivalent to a Station Blackout scenario, like a TMLB accident, with the only difference that in H2 sequence the scram is forced to occur with a delay of 28 seconds. The main events during the accident sequence are a loss of normal and auxiliary SG feedwater (0 s), followed by a scram when the water level in SG is equal or less than 0.7 m (after 28 seconds). There is also a main coolant pumps trip when {delta}Tsat < 10 deg. C, a total opening of the three relief valves when Tric (core maximal outlet temperature) is above 603 K (330 deg. C) and accumulators isolation when primary pressure goes below 1.5 MPa (15 bar). Among many other points, it is worth noting that this was the first time that a MELCOR 1.8.5 input deck was available for a French PWR 900. The main ENEA effort in this period was devoted to prepare the MELCOR input deck using the code version v.1.8.5 (build QZ Oct 2000 with the latest patch 185003 Oct 2001). The input deck, completely new, was prepared taking into account structure, data and same conditions as those found inside ASTEC input decks. The main goal of the work presented in this paper is to put in evidence where and when MELCOR provides good enough results and why, in some cases mainly referring to its specific models (candling, corium pool behaviour, etc.) they were less good. A future work will be the preparation of an input deck for the new MELCOR 1.8.6. and to perform a code-to-code comparison with ASTEC v1.2 rev. 1. (author)« less

Interim reliability evaluation program, Browns Ferry 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mays, S.E.; Poloski, J.P.; Sullivan, W.H.

1981-01-01

Probabilistic risk analysis techniques, i.e., event tree and fault tree analysis, were utilized to provide a risk assessment of the Browns Ferry Nuclear Plant Unit 1. Browns Ferry 1 is a General Electric boiling water reactor of the BWR 4 product line with a Mark 1 (drywell and torus) containment. Within the guidelines of the IREP Procedure and Schedule Guide, dominant accident sequences that contribute to public health and safety risks were identified and grouped according to release categories.

The effectiveness of using pictures in teaching young children about burn injury accidents.

PubMed

Liu, Hsueh-Fen; Lin, Fang-Suey; Chang, Chien-Ju

2015-11-01

This study utilized the "story grammar" approach (Stein and Glenn, 1979) to analyze the within-corpus differences in recounting of sixty 6- and 7-year-old children, specifically whether illustrations (5-factor accident sequence) were or were not resorted to as a means to assist their narration of a home accident in which a child received a burn injury from hot soup. Our investigation revealed that the message presentation strategy "combining oral and pictures" better helped young children to memorize the story content (sequence of events leading to the burn injury) than "oral only." Specifically, the content of "the dangerous objects that caused the injury", "the unsafe actions that people involved took", and "how the people involved felt about the severity of the accident" differed significantly between the two groups. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

TRAC-P1: an advanced best estimate computer program for PWR LOCA analysis. I. Methods, models, user information, and programming details

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-05-01

The Transient Reactor Analysis Code (TRAC) is being developed at the Los Alamos Scientific Laboratory (LASL) to provide an advanced ''best estimate'' predictive capability for the analysis of postulated accidents in light water reactors (LWRs). TRAC-Pl provides this analysis capability for pressurized water reactors (PWRs) and for a wide variety of thermal-hydraulic experimental facilities. It features a three-dimensional treatment of the pressure vessel and associated internals; two-phase nonequilibrium hydrodynamics models; flow-regime-dependent constitutive equation treatment; reflood tracking capability for both bottom flood and falling film quench fronts; and consistent treatment of entire accident sequences including the generation of consistent initial conditions.more » The TRAC-Pl User's Manual is composed of two separate volumes. Volume I gives a description of the thermal-hydraulic models and numerical solution methods used in the code. Detailed programming and user information is also provided. Volume II presents the results of the developmental verification calculations.« less

Interface requirements to couple thermal hydraulics codes to severe accident codes: ICARE/CATHARE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Camous, F.; Jacq, F.; Chatelard, P.

1997-07-01

In order to describe with the same code the whole sequence of severe LWR accidents, up to the vessel failure, the Institute of Protection and Nuclear Safety has performed a coupling of the severe accident code ICARE2 to the thermalhydraulics code CATHARE2. The resulting code, ICARE/CATHARE, is designed to be as pertinent as possible in all the phases of the accident. This paper is mainly devoted to the description of the ICARE2-CATHARE2 coupling.

Genesis Failure Investigation Report

NASA Technical Reports Server (NTRS)

Klein, John

2004-01-01

The-Genesis mission to collect solar-wind samples and return them to Earth for detailed analysis proceeded successfully for 3.5 years. During reentry on September 8, 2004, a failure in the entry, descent and landing sequence resulted in a crash landing of the Genesis sample return capsule. This document describes the findings of the avionics sub-team that supported the accident investigation of the JPL Failure Review Board.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.

Severe accident management can be defined as the use of existing and/or altemative resources, systems and actors to prevent or mitigate a core-melt accident. For each accident sequence and each combination of severe accident management strategies, there may be several options available to the operator, and each involves phenomenological and operational considerations regarding uncertainty. Operational uncertainties include operator, system and instrumentation behavior during an accident. A framework based on decision trees and influence diagrams has been developed which incorporates such criteria as feasibility, effectiveness, and adverse effects, for evaluating potential severe accident management strategies. The framework is also capable ofmore » propagating both data and model uncertainty. It is applied to several potential strategies including PWR cavity flooding, BWR drywell flooding, PWR depressurization and PWR feed and bleed.« less

Examination of Icing Induced Loss of Control and Its Mitigations

NASA Technical Reports Server (NTRS)

Reehorst, Andrew L.; Addy, Harold E., Jr.; Colantonio, Renato O.

2010-01-01

Factors external to the aircraft are often a significant causal factor in loss of control (LOC) accidents. In today s aviation world, very few accidents stem from a single cause and typically have a number of causal factors that culminate in a LOC accident. Very often the "trigger" that initiates an accident sequence is an external environment factor. In a recent NASA statistical analysis of LOC accidents, aircraft icing was shown to be the most common external environmental LOC causal factor for scheduled operations. When investigating LOC accident or incidents aircraft icing causal factors can be categorized into groups of 1) in-flight encounter with super-cooled liquid water clouds, 2) take-off with ice contamination, or 3) in-flight encounter with high concentrations of ice crystals. As with other flight hazards, icing induced LOC accidents can be prevented through avoidance, detection, and recovery mitigations. For icing hazards, avoidance can take the form of avoiding flight into icing conditions or avoiding the hazard of icing by making the aircraft tolerant to icing conditions. Icing detection mitigations can take the form of detecting icing conditions or detecting early performance degradation caused by icing. Recovery from icing induced LOC requires flight crew or automated systems capable of accounting for reduced aircraft performance and degraded control authority during the recovery maneuvers. In this report we review the icing induced LOC accident mitigations defined in a recent LOC study and for each mitigation describe a research topic required to enable or strengthen the mitigation. Many of these research topics are already included in ongoing or planned NASA icing research activities or are being addressed by members of the icing research community. These research activities are described and the status of the ongoing or planned research to address the technology needs is discussed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolaczkowski, A.M.; Lambright, J.A.; Ferrell, W.L.

This document contains the internal event initiated accident sequence analyses for Peach Bottom, Unit 2; one of the reference plants being examined as part of the NUREG-1150 effort by the Nuclear Regulatory Commission. NUREG-1150 will document the risk of a selected group of nuclear power plants. As part of that work, this report contains the overall core damage frequency estimate for Peach Bottom, Unit 2, and the accompanying plant damage state frequencies. Sensitivity and uncertainty analyses provided additional insights regarding the dominant contributors to the Peach Bottom core damage frequency estimate. The mean core damage frequency at Peach Bottom wasmore » calculated to be 8.2E-6. Station blackout type accidents (loss of all ac power) were found to dominate the overall results. Anticipated Transient Without Scram accidents were also found to be non-negligible contributors. The numerical results are largely driven by common mode failure probability estimates and to some extent, human error. Because of significant data and analysis uncertainties in these two areas (important, for instance, to the most dominant scenario in this study), it is recommended that the results of the uncertainty and sensitivity analyses be considered before any actions are taken based on this analysis.« less

Evaluation of potential severe accidents during low power and shutdown operations at Surry, Unit 1: Analysis of core damage frequency from internal events during mid-loop operations, Appendices E (Sections E.1--E.8). Volume 2, Part 3A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, T.L.; Musicki, Z.; Kohut, P.

1994-06-01

During 1989, the Nuclear Regulatory Commission (NRC) initiated an extensive program to carefully examine the potential risks during low power and shutdown operations. The program includes two parallel projects being performed by Brookhaven National Laboratory (BNL) and Sandia National Laboratories (SNL). Two plants, Surry (pressurized water reactor) and Grand Gulf (boiling water reactor), were selected as the plants to be studied. The objectives of the program are to assess the risks of severe accidents initiated during plant operational states other than full power operation and to compare the estimated core damage frequencies, important accident sequences and other qualitative and quantitativemore » results with those accidents initiated during full power operation as assessed in NUREG-1150. The objective of this report is to document the approach utilized in the Surry plant and discuss the results obtained. A parallel report for the Grand Gulf plant is prepared by SNL. This study shows that the core-damage frequency during mid-loop operation at the Surry plant is comparable to that of power operation. The authors recognize that there is very large uncertainty in the human error probabilities in this study. This study identified that only a few procedures are available for mitigating accidents that may occur during shutdown. Procedures written specifically for shutdown accidents would be useful.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattison, M.B.

The Idaho National Engineering Laboratory (INEL) over the three years has created 75 plant-specific Accident Sequence Precursor (ASP) models using the SAPHIRE suite of PRA codes. Along with the new models, the INEL has also developed a new module for SAPHIRE which is tailored specifically to the unique needs of ASP evaluations. These models and software will be the next generation of risk tools for the evaluation of accident precursors by both the U.S. Nuclear Regulatory Commission`s (NRC`s) Office of Nuclear Reactor Regulation (NRR) and the Office for Analysis and Evaluation of Operational Data (AEOD). This paper presents an overviewmore » of the models and software. Key characteristics include: (1) classification of the plant models according to plant response with a unique set of event trees for each plant class, (2) plant-specific fault trees using supercomponents, (3) generation and retention of all system and sequence cutsets, (4) full flexibility in modifying logic, regenerating cutsets, and requantifying results, and (5) user interface for streamlined evaluation of ASP events. Future plans for the ASP models is also presented.« less

Developing techniques for cause-responsibility analysis of occupational accidents.

PubMed

Jabbari, Mousa; Ghorbani, Roghayeh

2016-11-01

The aim of this study was to specify the causes of occupational accidents, determine social responsibility and the role of groups involved in work-related accidents. This study develops occupational accidents causes tree, occupational accidents responsibility tree, and occupational accidents component-responsibility analysis worksheet; based on these methods, it develops cause-responsibility analysis (CRA) techniques, and for testing them, analyzes 100 fatal/disabling occupational accidents in the construction setting that were randomly selected from all the work-related accidents in Tehran, Iran, over a 5-year period (2010-2014). The main result of this study involves two techniques for CRA: occupational accidents tree analysis (OATA) and occupational accidents components analysis (OACA), used in parallel for determination of responsible groups and responsibilities rate. From the results, we find that the management group of construction projects has 74.65% responsibility of work-related accidents. The developed techniques are purposeful for occupational accidents investigation/analysis, especially for the determination of detailed list of tasks, responsibilities, and their rates. Therefore, it is useful for preventing work-related accidents by focusing on the responsible group's duties. Copyright © 2016 Elsevier Ltd. All rights reserved.

Major Accidents (Gray Swans) Likelihood Modeling Using Accident Precursors and Approximate Reasoning.

PubMed

Khakzad, Nima; Khan, Faisal; Amyotte, Paul

2015-07-01

Compared to the remarkable progress in risk analysis of normal accidents, the risk analysis of major accidents has not been so well-established, partly due to the complexity of such accidents and partly due to low probabilities involved. The issue of low probabilities normally arises from the scarcity of major accidents' relevant data since such accidents are few and far between. In this work, knowing that major accidents are frequently preceded by accident precursors, a novel precursor-based methodology has been developed for likelihood modeling of major accidents in critical infrastructures based on a unique combination of accident precursor data, information theory, and approximate reasoning. For this purpose, we have introduced an innovative application of information analysis to identify the most informative near accident of a major accident. The observed data of the near accident were then used to establish predictive scenarios to foresee the occurrence of the major accident. We verified the methodology using offshore blowouts in the Gulf of Mexico, and then demonstrated its application to dam breaches in the United Sates. © 2015 Society for Risk Analysis.

Evaluation of potential severe accidents during low power and shutdown operations at Surry, Unit 1: Analysis of core damage frequency from internal events during mid-loop operations, Appendices A--D. Volume 2, Part 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, T.L.; Musicki, Z.; Kohut, P.

1994-06-01

During 1989, the Nuclear Regulatory Commission (NRC) initiated an extensive program to carefully examine the Potential risks during low Power and shutdown operations. The program includes two parallel projects being performed by Brookhaven National Laboratory (BNL) and Sandia National Laboratories (SNL). Two plants, Surry (pressurized water reactor) and Grand Gulf (boiling water reactor), were selected as the Plants to be studied. The objectives of the program are to assess the risks of severe accidents initiated during plant operational states other than full power operation and to compare the estimated core damage frequencies, important accident sequences and other qualitative and quantitativemore » results with those accidents initiated during full power operation as assessed in NUREG-1150. The objective of this report is to document the approach utilized in the Surry plant and discuss the results obtained. A parallel report for the Grand Gulf plant is prepared by SNL. This study shows that the core-damage frequency during mid-loop operation at the Surry plant is comparable to that of power operation. We recognize that there is very large uncertainty in the human error probabilities in this study. This study identified that only a few procedures are available for mitigating accidents that may occur during shutdown. Procedures written specifically for shutdown accidents would be useful. This document, Volume 2, Pt. 2 provides appendices A through D of this report.« less

Psychophysiological and other factors affecting human performance in accident prevention and investigation. [Comparison of aviation with other industries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klinestiver, L.R.

Psychophysiological factors are not uncommon terms in the aviation incident/accident investigation sequence where human error is involved. It is highly suspect that the same psychophysiological factors may also exist in the industrial arena where operator personnel function; but, there is little evidence in literature indicating how management and subordinates cope with these factors to prevent or reduce accidents. It is apparent that human factors psychophysological training is quite evident in the aviation industry. However, while the industrial arena appears to analyze psychophysiological factors in accident investigations, there is little evidence that established training programs exist for supervisors and operator personnel.

Validity and consistency assessment of accident analysis methods in the petroleum industry.

PubMed

Ahmadi, Omran; Mortazavi, Seyed Bagher; Khavanin, Ali; Mokarami, Hamidreza

2017-11-17

Accident analysis is the main aspect of accident investigation. It includes the method of connecting different causes in a procedural way. Therefore, it is important to use valid and reliable methods for the investigation of different causal factors of accidents, especially the noteworthy ones. This study aimed to prominently assess the accuracy (sensitivity index [SI]) and consistency of the six most commonly used accident analysis methods in the petroleum industry. In order to evaluate the methods of accident analysis, two real case studies (process safety and personal accident) from the petroleum industry were analyzed by 10 assessors. The accuracy and consistency of these methods were then evaluated. The assessors were trained in the workshop of accident analysis methods. The systematic cause analysis technique and bowtie methods gained the greatest SI scores for both personal and process safety accidents, respectively. The best average results of the consistency in a single method (based on 10 independent assessors) were in the region of 70%. This study confirmed that the application of methods with pre-defined causes and a logic tree could enhance the sensitivity and consistency of accident analysis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daling, P.M.; Marler, J.E.; Vo, T.V.

This study evaluates the values (benefits) and impacts (costs) associated with potential resolutions to Generic Issue 143, ``Availability of HVAC and Chilled Water Systems.`` The study identifies vulnerabilities related to failures of HVAC, chilled water, and room cooling systems; develops estimates of room heatup rates and safety-related equipment vulnerabilities following losses of HVAC/room cooler systems; develops estimates of the core damage frequencies and public risks associated with failures of these systems; develops three proposed resolution strategies to this generic issue; and performs a value/impact analysis of the proposed resolutions. Existing probabilistic risk assessments for four representative plants, including one plantmore » from each vendor, form the basis for the core damage frequency and public risk calculations. Both internal and external events were considered. It was concluded that all three proposed resolution strategies exceed the $1,000/person-rem cost-effectiveness ratio. Additional evaluations were performed to develop ``generic`` insights on potential design-related and configuration-related vulnerabilities and potential high-frequency ({approximately}1E-04/RY) accident sequences that involve failures of HVAC/room cooling functions. It was concluded that, although high-frequency accident sequences may exist at some plants, these high-frequency sequences are plant-specific in nature or have been resolved through hardware and/or operational changes. The plant-specific Individual Plant Examinations are an effective vehicle for identification and resolution of these plant-specific anomalies and hardware configurations.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, M. T.

The overall objective of the current work is to carry out a scoping analysis to determine the impact of ATF on late phase accident progression; in particular, the molten core-concrete interaction portion of the sequence that occurs after the core debris fails the reactor vessel and relocates into containment. This additional study augments previous work by including kinetic effects that govern chemical reaction rates during core-concrete interaction. The specific ATF considered as part of this study is SiC-clad UO 2.

Methods for external event screening quantification: Risk Methods Integration and Evaluation Program (RMIEP) methods development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ravindra, M.K.; Banon, H.

1992-07-01

In this report, the scoping quantification procedures for external events in probabilistic risk assessments of nuclear power plants are described. External event analysis in a PRA has three important goals; (1) the analysis should be complete in that all events are considered; (2) by following some selected screening criteria, the more significant events are identified for detailed analysis; (3) the selected events are analyzed in depth by taking into account the unique features of the events: hazard, fragility of structures and equipment, external-event initiated accident sequences, etc. Based on the above goals, external event analysis may be considered as amore » three-stage process: Stage I: Identification and Initial Screening of External Events; Stage II: Bounding Analysis; Stage III: Detailed Risk Analysis. In the present report, first, a review of published PRAs is given to focus on the significance and treatment of external events in full-scope PRAs. Except for seismic, flooding, fire, and extreme wind events, the contributions of other external events to plant risk have been found to be negligible. Second, scoping methods for external events not covered in detail in the NRC's PRA Procedures Guide are provided. For this purpose, bounding analyses for transportation accidents, extreme winds and tornadoes, aircraft impacts, turbine missiles, and chemical release are described.« less

The role of PRA in the safety assessment of VVER Nuclear Power Plants in Ukraine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kot, C.

1999-05-10

Ukraine operates thirteen (13) Soviet-designed pressurized water reactors, VVERS. All Ukrainian plants are currently operating with annually renewable permits until they update their safety analysis reports (SARs), in accordance with new SAR content requirements issued in September 1995, by the Nuclear Regulatory Authority and the Government Nuclear Power Coordinating Committee of Ukraine. The requirements are in three major areas: design basis accident (DBA) analysis, probabilistic risk assessment (PRA), and beyond design-basis accident (BDBA) analysis. The last two requirements, on PRA and BDBA, are new, and the DBA requirements are an expanded version of the older SAR requirements. The US Departmentmore » of Energy (USDOE), as part of its Soviet-Designed Reactor Safety activities, is providing assistance and technology transfer to Ukraine to support their nuclear power plants (NPPs) in developing a Western-type technical basis for the new SARs. USDOE sponsored In-Depth Safety Assessments (ISAs) are in progress at three pilot nuclear reactor units in Ukraine, South Ukraine Unit 1, Zaporizhzhya Unit 5, and Rivne Unit 1, and a follow-on study has been initiated at Khmenytskyy Unit 1. The ISA projects encompass most areas of plant safety evaluation, but the initial emphasis is on performing a detailed, plant-specific Level 1 Internal Events PRA. This allows the early definition of the plant risk profile, the identification of risk significant accident sequences and plant vulnerabilities and provides guidance for the remainder of the safety assessments.« less

Applying STAMP in Accident Analysis

NASA Technical Reports Server (NTRS)

Leveson, Nancy; Daouk, Mirna; Dulac, Nicolas; Marais, Karen

2003-01-01

Accident models play a critical role in accident investigation and analysis. Most traditional models are based on an underlying chain of events. These models, however, have serious limitations when used for complex, socio-technical systems. Previously, Leveson proposed a new accident model (STAMP) based on system theory. In STAMP, the basic concept is not an event but a constraint. This paper shows how STAMP can be applied to accident analysis using three different views or models of the accident process and proposes a notation for describing this process.

Single pilot IFR accident data analysis

NASA Technical Reports Server (NTRS)

Harris, D. F.

1983-01-01

The aircraft accident data recorded by the National Transportation and Safety Board (NTSR) for 1964-1979 were analyzed to determine what problems exist in the general aviation (GA) single pilot instrument flight rule (SPIFR) environment. A previous study conducted in 1978 for the years 1964-1975 provided a basis for comparison. This effort was generally limited to SPIFR pilot error landing phase accidents but includes some SPIFR takeoff and enroute accident analysis as well as some dual pilot IFR accident analysis for comparison. Analysis was performed for 554 accidents of which 39% (216) occurred during the years 1976-1979.

Civil helicopter wire strike assessment study. Volume 2: Accident analysis briefs

NASA Technical Reports Server (NTRS)

Tuomela, C. H.; Brennan, M. F.

1980-01-01

A description and analysis of each of the 208 civil helicopter wire strike accidents reported to the National Transportation Safety Board (NTSB) for the ten year period 1970-1979 is given. The accident analysis briefs were based on pilot reports, FAA investigation reports, and such accident photographs as were made available. Briefs were grouped by year and, within year, by NTSB accident report number.

Chemistry, the Central Science? The History of the High School Science Sequence

ERIC Educational Resources Information Center

Sheppard, Keith; Robbins, Dennis M.

2005-01-01

Chemistry became the ''central science'' not by design but by accident in the US high schools. The three important factors, which had their influence on the high school science, are sequenced and their impact on the development of US science education, are mentioned.

Prediction accident triangle in maintenance of underground mine facilities using Poisson distribution analysis

NASA Astrophysics Data System (ADS)

Khuluqi, M. H.; Prapdito, R. R.; Sambodo, F. P.

2018-04-01

In Indonesia, mining is categorized as a hazardous industry. In recent years, a dramatic increase of mining equipment and technological complexities had resulted in higher maintenance expectations that accompanied by the changes in the working conditions, especially on safety. Ensuring safety during the process of conducting maintenance works in underground mine is important as an integral part of accident prevention programs. Accident triangle has provided a support to safety practitioner to draw a road map in preventing accidents. Poisson distribution is appropriate for the analysis of accidents at a specific site in a given time period. Based on the analysis of accident statistics in the underground mine maintenance of PT. Freeport Indonesia from 2011 through 2016, it is found that 12 minor accidents for 1 major accident and 66 equipment damages for 1 major accident as a new value of accident triangle. The result can be used for the future need for improving the accident prevention programs.

Safety Analysis and Protection Measures of the Control System of the Pulsed High Magnetic Field Facility in WHMFC

NASA Astrophysics Data System (ADS)

Shi, J. T.; Han, X. T.; Xie, J. F.; Yao, L.; Huang, L. T.; Li, L.

2013-03-01

A Pulsed High Magnetic Field Facility (PHMFF) has been established in Wuhan National High Magnetic Field Center (WHMFC) and various protection measures are applied in its control system. In order to improve the reliability and robustness of the control system, the safety analysis of the PHMFF is carried out based on Fault Tree Analysis (FTA) technique. The function and realization of 5 protection systems, which include sequence experiment operation system, safety assistant system, emergency stop system, fault detecting and processing system and accident isolating protection system, are given. The tests and operation indicate that these measures improve the safety of the facility and ensure the safety of people.

A smart phone-based pocket fall accident detection, positioning, and rescue system.

PubMed

Kau, Lih-Jen; Chen, Chih-Sheng

2015-01-01

We propose in this paper a novel algorithm as well as architecture for the fall accident detection and corresponding wide area rescue system based on a smart phone and the third generation (3G) networks. To realize the fall detection algorithm, the angles acquired by the electronic compass (ecompass) and the waveform sequence of the triaxial accelerometer on the smart phone are used as the system inputs. The acquired signals are then used to generate an ordered feature sequence and then examined in a sequential manner by the proposed cascade classifier for recognition purpose. Once the corresponding feature is verified by the classifier at current state, it can proceed to next state; otherwise, the system will reset to the initial state and wait for the appearance of another feature sequence. Once a fall accident event is detected, the user's position can be acquired by the global positioning system (GPS) or the assisted GPS, and sent to the rescue center via the 3G communication network so that the user can get medical help immediately. With the proposed cascaded classification architecture, the computational burden and power consumption issue on the smart phone system can be alleviated. Moreover, as we will see in the experiment that a distinguished fall accident detection accuracy up to 92% on the sensitivity and 99.75% on the specificity can be obtained when a set of 450 test actions in nine different kinds of activities are estimated by using the proposed cascaded classifier, which justifies the superiority of the proposed algorithm.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curry, J J; Gallagher, D W; Modarres, M

Appendices are presented concerning isolation condenser makeup; vapor suppression system; station air system; reactor building closed cooling water system; turbine building secondary closed water system; service water system; emergency service water system; fire protection system; emergency ac power; dc power system; event probability estimation; methodology of accident sequence quantification; and assignment of dominant sequences to release categories.

Development of Database for Accident Analysis in Indian Mines

NASA Astrophysics Data System (ADS)

Tripathy, Debi Prasad; Guru Raghavendra Reddy, K.

2016-10-01

Mining is a hazardous industry and high accident rates associated with underground mining is a cause of deep concern. Technological developments notwithstanding, rate of fatal accidents and reportable incidents have not shown corresponding levels of decline. This paper argues that adoption of appropriate safety standards by both mine management and the government may result in appreciable reduction in accident frequency. This can be achieved by using the technology in improving the working conditions, sensitising workers and managers about causes and prevention of accidents. Inputs required for a detailed analysis of an accident include information on location, time, type, cost of accident, victim, nature of injury, personal and environmental factors etc. Such information can be generated from data available in the standard coded accident report form. This paper presents a web based application for accident analysis in Indian mines during 2001-2013. An accident database (SafeStat) prototype based on Intranet of the TCP/IP agreement, as developed by the authors, is also discussed.

Scoping Study Investigating PWR Instrumentation during a Severe Accident Scenario

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rempe, J. L.; Knudson, D. L.; Lutz, R. J.

The accidents at the Three Mile Island Unit 2 (TMI-2) and Fukushima Daiichi Units 1, 2, and 3 nuclear power plants demonstrate the critical importance of accurate, relevant, and timely information on the status of reactor systems during a severe accident. These events also highlight the critical importance of understanding and focusing on the key elements of system status information in an environment where operators may be overwhelmed with superfluous and sometimes conflicting data. While progress in these areas has been made since TMI-2, the events at Fukushima suggests that there may still be a potential need to ensure thatmore » critical plant information is available to plant operators. Recognizing the significant technical and economic challenges associated with plant modifications, it is important to focus on instrumentation that can address these information critical needs. As part of a program initiated by the Department of Energy, Office of Nuclear Energy (DOE-NE), a scoping effort was initiated to assess critical information needs identified for severe accident management and mitigation in commercial Light Water Reactors (LWRs), to quantify the environment instruments monitoring this data would have to survive, and to identify gaps where predicted environments exceed instrumentation qualification envelop (QE) limits. Results from the Pressurized Water Reactor (PWR) scoping evaluations are documented in this report. The PWR evaluations were limited in this scoping evaluation to quantifying the environmental conditions for an unmitigated Short-Term Station BlackOut (STSBO) sequence in one unit at the Surry nuclear power station. Results were obtained using the MELCOR models developed for the US Nuclear Regulatory Commission (NRC)-sponsored State of the Art Consequence Assessment (SOARCA) program project. Results from this scoping evaluation indicate that some instrumentation identified to provide critical information would be exposed to conditions that significantly exceeded QE limits for extended time periods for the low frequency STSBO sequence evaluated in this study. It is recognized that the core damage frequency (CDF) of the sequence evaluated in this scoping effort would be considerably lower if evaluations considered new FLEX equipment being installed by industry. Nevertheless, because of uncertainties in instrumentation response when exposed to conditions beyond QE limits and alternate challenges associated with different sequences that may impact sensor performance, it is recommended that additional evaluations of instrumentation performance be completed to provide confidence that operators have access to accurate, relevant, and timely information on the status of reactor systems for a broad range of challenges associated with risk important severe accident sequences.« less

Type A Accident Investigation Board report on the January 17, 1996, electrical accident with injury in Technical Area 21 Tritium Science and Fabrication Facility Los Alamos National Laboratory. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-04-01

An electrical accident was investigated in which a crafts person received serious injuries as a result of coming into contact with a 13.2 kilovolt (kV) electrical cable in the basement of Building 209 in Technical Area 21 (TA-21-209) in the Tritium Science and Fabrication Facility (TSFF) at Los Alamos National Laboratory (LANL). In conducting its investigation, the Accident Investigation Board used various analytical techniques, including events and causal factor analysis, barrier analysis, change analysis, fault tree analysis, materials analysis, and root cause analysis. The board inspected the accident site, reviewed events surrounding the accident, conducted extensive interviews and document reviews,more » and performed causation analyses to determine the factors that contributed to the accident, including any management system deficiencies. Relevant management systems and factors that could have contributed to the accident were evaluated in accordance with the guiding principles of safety management identified by the Secretary of Energy in an October 1994 letter to the Defense Nuclear Facilities Safety Board and subsequently to Congress.« less

Truck accidents at freeway ramps : data analysis and high-risk site identification

DOT National Transportation Integrated Search

1998-01-01

To examine the relationship of ramp design to truck accident rates, this paper presents an analysis of truck accidents in Washington State, plus a comparison to limited data from Colorado and California. The authors group freeway truck accidents by r...

Systems thinking, the Swiss Cheese Model and accident analysis: a comparative systemic analysis of the Grayrigg train derailment using the ATSB, AcciMap and STAMP models.

PubMed

Underwood, Peter; Waterson, Patrick

2014-07-01

The Swiss Cheese Model (SCM) is the most popular accident causation model and is widely used throughout various industries. A debate exists in the research literature over whether the SCM remains a viable tool for accident analysis. Critics of the model suggest that it provides a sequential, oversimplified view of accidents. Conversely, proponents suggest that it embodies the concepts of systems theory, as per the contemporary systemic analysis techniques. The aim of this paper was to consider whether the SCM can provide a systems thinking approach and remain a viable option for accident analysis. To achieve this, the train derailment at Grayrigg was analysed with an SCM-based model (the ATSB accident investigation model) and two systemic accident analysis methods (AcciMap and STAMP). The analysis outputs and usage of the techniques were compared. The findings of the study showed that each model applied the systems thinking approach. However, the ATSB model and AcciMap graphically presented their findings in a more succinct manner, whereas STAMP more clearly embodied the concepts of systems theory. The study suggests that, whilst the selection of an analysis method is subject to trade-offs that practitioners and researchers must make, the SCM remains a viable model for accident analysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

Final safety analysis report for the Galileo Mission: Volume 2: Book 1, Accident model document

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Accident Model Document (AMD) is the second volume of the three volume Final Safety Analysis Report (FSAR) for the Galileo outer planetary space science mission. This mission employs Radioisotope Thermoelectric Generators (RTGs) as the prime electrical power sources for the spacecraft. Galileo will be launched into Earth orbit using the Space Shuttle and will use the Inertial Upper Stage (IUS) booster to place the spacecraft into an Earth escape trajectory. The RTG's employ silicon-germanium thermoelectric couples to produce electricity from the heat energy that results from the decay of the radioisotope fuel, Plutonium-238, used in the RTG heat source.more » The heat source configuration used in the RTG's is termed General Purpose Heat Source (GPHS), and the RTG's are designated GPHS-RTGs. The use of radioactive material in these missions necessitates evaluations of the radiological risks that may be encountered by launch complex personnel as well as by the Earth's general population resulting from postulated malfunctions or failures occurring in the mission operations. The FSAR presents the results of a rigorous safety assessment, including substantial analyses and testing, of the launch and deployment of the RTGs for the Galileo mission. This AMD is a summary of the potential accident and failure sequences which might result in fuel release, the analysis and testing methods employed, and the predicted source terms. Each source term consists of a quantity of fuel released, the location of release and the physical characteristics of the fuel released. Each source term has an associated probability of occurrence. 27 figs., 11 tabs.« less

An Evidential Reasoning-Based CREAM to Human Reliability Analysis in Maritime Accident Process.

PubMed

Wu, Bing; Yan, Xinping; Wang, Yang; Soares, C Guedes

2017-10-01

This article proposes a modified cognitive reliability and error analysis method (CREAM) for estimating the human error probability in the maritime accident process on the basis of an evidential reasoning approach. This modified CREAM is developed to precisely quantify the linguistic variables of the common performance conditions and to overcome the problem of ignoring the uncertainty caused by incomplete information in the existing CREAM models. Moreover, this article views maritime accident development from the sequential perspective, where a scenario- and barrier-based framework is proposed to describe the maritime accident process. This evidential reasoning-based CREAM approach together with the proposed accident development framework are applied to human reliability analysis of a ship capsizing accident. It will facilitate subjective human reliability analysis in different engineering systems where uncertainty exists in practice. © 2017 Society for Risk Analysis.

Methods for external event screening quantification: Risk Methods Integration and Evaluation Program (RMIEP) methods development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ravindra, M.K.; Banon, H.

1992-07-01

In this report, the scoping quantification procedures for external events in probabilistic risk assessments of nuclear power plants are described. External event analysis in a PRA has three important goals; (1) the analysis should be complete in that all events are considered; (2) by following some selected screening criteria, the more significant events are identified for detailed analysis; (3) the selected events are analyzed in depth by taking into account the unique features of the events: hazard, fragility of structures and equipment, external-event initiated accident sequences, etc. Based on the above goals, external event analysis may be considered as amore » three-stage process: Stage I: Identification and Initial Screening of External Events; Stage II: Bounding Analysis; Stage III: Detailed Risk Analysis. In the present report, first, a review of published PRAs is given to focus on the significance and treatment of external events in full-scope PRAs. Except for seismic, flooding, fire, and extreme wind events, the contributions of other external events to plant risk have been found to be negligible. Second, scoping methods for external events not covered in detail in the NRC`s PRA Procedures Guide are provided. For this purpose, bounding analyses for transportation accidents, extreme winds and tornadoes, aircraft impacts, turbine missiles, and chemical release are described.« less

A comprehensive review of rollover accidents involving vehicles equipped with Electronic Stability Control (ESC) systems.

PubMed

Padmanaban, Jeya; Shields, Leland E; Scheibe, Robert R; Eyges, Vitaly E

2008-10-01

This study investigated 478 police accident reports from 9 states to examine and characterize rollover crashes involving ESC-equipped vehicles. The focus was on the sequence of critical events leading to loss of control and rollover, and the interactions between the accident, driver, and environment. Results show that, while ESC is effective in reducing loss of control leading to certain rollover crashes, its effectiveness is diminished in others, particularly when the vehicle departs the roadway or when environmental factors such as slick road conditions or driver factors such as speeding, distraction, fatigue, impairment, or overcorrection are present.

A Comprehensive Review of Rollover Accidents Involving Vehicles Equipped with Electronic Stability Control (ESC) Systems

PubMed Central

Padmanaban, Jeya; Shields, Leland E.; Scheibe, Robert R.; Eyges, Vitaly E.

2008-01-01

This study investigated 478 police accident reports from 9 states to examine and characterize rollover crashes involving ESC-equipped vehicles. The focus was on the sequence of critical events leading to loss of control and rollover, and the interactions between the accident, driver, and environment. Results show that, while ESC is effective in reducing loss of control leading to certain rollover crashes, its effectiveness is diminished in others, particularly when the vehicle departs the roadway or when environmental factors such as slick road conditions or driver factors such as speeding, distraction, fatigue, impairment, or overcorrection are present. PMID:19026219

Canister Storage Building (CSB) Design Basis Accident Analysis Documentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

CROWE, R.D.; PIEPHO, M.G.

2000-03-23

This document provided the detailed accident analysis to support HNF-3553, Spent Nuclear Fuel Project Final Safety Analysis Report, Annex A, ''Canister Storage Building Final Safety Analysis Report''. All assumptions, parameters, and models used to provide the analysis of the design basis accidents are documented to support the conclusions in the Canister Storage Building Final Safety Analysis Report.

10 CFR 50.43 - Additional standards and provisions affecting class 103 licenses and certifications for...

Code of Federal Regulations, 2010 CFR

2010-01-01

... licensed before 1997, or use simplified, inherent, passive, or other innovative means to accomplish their... sequences, including equilibrium core conditions; or (2) There has been acceptable testing of a prototype... accident sequences, including equilibrium core conditions. If a prototype plant is used to comply with the...

Indonesian Sea Accident Analysis (Case Study From 2003 – 2013)

NASA Astrophysics Data System (ADS)

Arya Dewanto, Y.; Faturachman, D.

2018-03-01

There are so many accidents in sea transportation in Indonesia. Most of the accidents happen because of low concern aspects of the safety and security of the crew. In sailing, a man as transport users to interact with the ship and the surrounding environment (including other ships, cruise lines, ports, and the situation of local conditions). These interactions are sometimes very complex and related to various aspects of. Aware of the multiplicity of aspects related to the third of these factors, seeking the safety of cruise through a reduction in the number of accidents and the risk of death and serious injuries due to accidents and goods transported is certainly not enough attempted through mono-sector approach, but rather takes a multi-sector approach to the efforts. In this paper, we described the Indonesian Sea Transportation accident analysis for eleven years divided into four items: total of ship accident type, ship accident factor, total of casualties, region of ship accidents. All data founded from Marine Court (Mahkamah Pelayaran). From that 4 items we can find Indonesia Sea Accident Analysis from 2003-2013.

A cluster analysis on road traffic accidents using genetic algorithms

NASA Astrophysics Data System (ADS)

Saharan, Sabariah; Baragona, Roberto

2017-04-01

The analysis of traffic road accidents is increasingly important because of the accidents cost and public road safety. The availability or large data sets makes the study of factors that affect the frequency and severity accidents are viable. However, the data are often highly unbalanced and overlapped. We deal with the data set of the road traffic accidents recorded in Christchurch, New Zealand, from 2000-2009 with a total of 26440 accidents. The data is in a binary set and there are 50 factors road traffic accidents with four level of severity. We used genetic algorithm for the analysis because we are in the presence of a large unbalanced data set and standard clustering like k-means algorithm may not be suitable for the task. The genetic algorithm based on clustering for unknown K, (GCUK) has been used to identify the factors associated with accidents of different levels of severity. The results provided us with an interesting insight into the relationship between factors and accidents severity level and suggest that the two main factors that contributes to fatal accidents are "Speed greater than 60 km h" and "Did not see other people until it was too late". A comparison with the k-means algorithm and the independent component analysis is performed to validate the results.

Road Traffic Accident Analysis of Ajmer City Using Remote Sensing and GIS Technology

NASA Astrophysics Data System (ADS)

Bhalla, P.; Tripathi, S.; Palria, S.

2014-12-01

With advancement in technology, new and sophisticated models of vehicle are available and their numbers are increasing day by day. A traffic accident has multi-facet characteristics associated with it. In India 93% of crashes occur due to Human induced factor (wholly or partly). For proper traffic accident analysis use of GIS technology has become an inevitable tool. The traditional accident database is a summary spreadsheet format using codes and mileposts to denote location, type and severity of accidents. Geo-referenced accident database is location-referenced. It incorporates a GIS graphical interface with the accident information to allow for query searches on various accident attributes. Ajmer city, headquarter of Ajmer district, Rajasthan has been selected as the study area. According to Police records, 1531 accidents occur during 2009-2013. Maximum accident occurs in 2009 and the maximum death in 2013. Cars, jeeps, auto, pickup and tempo are mostly responsible for accidents and that the occurrence of accidents is mostly concentrated between 4PM to 10PM. GIS has proved to be a good tool for analyzing multifaceted nature of accidents. While road safety is a critical issue, yet it is handled in an adhoc manner. This Study is a demonstration of application of GIS for developing an efficient database on road accidents taking Ajmer City as a study. If such type of database is developed for other cities, a proper analysis of accidents can be undertaken and suitable management strategies for traffic regulation can be successfully proposed.

Challenging the immediate causes: A work accident investigation in an oil refinery using organizational analysis.

PubMed

Beltran, Sandra Lorena; Vilela, Rodolfo Andrade de Gouveia; de Almeida, Ildeberto Muniz

2018-01-01

In many companies, investigations of accidents still blame the victims without exploring deeper causes. Those investigations are reactive and have no learning potential. This paper aims to debate the historical organizational aspects of a company whose policy was incubating an accident. The empirical data are analyzed as part of a qualitative study of an accident that occurred in an oil refinery in Brazil in 2014. To investigate and analyse this case we used one-to-one and group interviews, participant observation, Collective Analyses of Work and a documentary review. The analysis was conducted on the basis of concepts of the Organizational Analysis of the event and the Model for Analysis and Prevention of Work Accidents. The accident had its origin in the interaction of social and organizational factors, among them being: excessively standardized culture, management tools and outcome indicators that give a false sense of safety, the decision to speed up the project, the change of operator to facilitate this outcome and performance management that encourages getting around the usual barriers. The superficial accident analysis conducted by the company that ignored human and organizational factors reinforces the traditional safety culture and favors the occurrence of new accidents.

Wet weather highway accident analysis and skid resistance data management system (volume I).

DOT National Transportation Integrated Search

1992-06-01

The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

Investigation of Containment Flooding Strategy for Mark-III Nuclear Power Plant with MAAP4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su Weinian; Wang, S.-J.; Chiang, S.-C

2005-06-15

Containment flooding is an important strategy for severe accident management of a conventional boiling water reactor (BWR) system. The purpose of this work is to investigate the containment flooding strategy of the Mark-III system after a reactor pressure vessel (RPV) breach. The Kuosheng Power Plant is a typical BWR-6 nuclear power plant (NPP) with Mark-III containment. The Severe Accident Management Guideline (SAMG) of the Kuosheng NPP has been developed based on the BWR Owners Group (BWROG) Emergency Procedure and Severe Accident Guidelines, Rev. 2. Therefore, the Kuosheng NPP is selected as the plant for study, and the MAAP4 code ismore » chosen as the tool for analysis. A postulated specific station blackout sequence for the Kuosheng NPP is cited as a reference case for this analysis. Because of the design features of Mark-III containment, the debris in the reactor cavity may not be submerged after an RPV breach when one follows the containment flooding strategy as suggested in the BWROG generic guideline, and the containment integrity could be challenged eventually. A more specific containment flooding strategy with drywell venting after an RPV breach is investigated, and a more stable plant condition is achieved with this strategy. Accordingly, the containment flooding strategy after an RPV breach will be modified for the Kuosheng SAMG, and these results are applicable to typical Mark-III plants with drywell vent path.« less

Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong.

PubMed

Wong, Francis K W; Chan, Albert P C; Wong, Andy K D; Hon, Carol K H; Choi, Tracy N Y

2018-03-10

A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the "Public Works Programme Construction Site Safety and Environmental Statistics" (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to 'fall of person from height'; (2) electricians with zero to five years of experience were prone to 'slip, trip or fall on same level'; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched.

Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong

PubMed Central

Wong, Francis K. W.; Chan, Albert P. C.; Wong, Andy K. D.; Choi, Tracy N. Y.

2018-01-01

A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the “Public Works Programme Construction Site Safety and Environmental Statistics” (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to ‘fall of person from height’; (2) electricians with zero to five years of experience were prone to ‘slip, trip or fall on same level’; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched. PMID:29534429

Wet weather highway accident analysis and skid resistance data management system (volume II : user's manual).

DOT National Transportation Integrated Search

1992-06-01

The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

Who by accident? The social morphology of car accidents.

PubMed

Factor, Roni; Yair, Gad; Mahalel, David

2010-09-01

Prior studies in the sociology of accidents have shown that different social groups have different rates of accident involvement. This study extends those studies by implementing Bourdieu's relational perspective of social space to systematically explore the homology between drivers' social characteristics and their involvement in specific types of motor vehicle accident. Using a large database that merges official Israeli road-accident records with socioeconomic data from two censuses, this research maps the social order of road accidents through multiple correspondence analysis. Extending prior studies, the results show that different social groups indeed tend to be involved in motor vehicle accidents of different types and severity. For example, we find that drivers from low socioeconomic backgrounds are overinvolved in severe accidents with fatal outcomes. The new findings reported here shed light on the social regularity of road accidents and expose new facets in the social organization of death. © 2010 Society for Risk Analysis.

Design and application of a tool for structuring, capitalizing and making more accessible information and lessons learned from accidents involving machinery.

PubMed

Sadeghi, Samira; Sadeghi, Leyla; Tricot, Nicolas; Mathieu, Luc

2017-12-01

Accident reports are published in order to communicate the information and lessons learned from accidents. An efficient accident recording and analysis system is a necessary step towards improvement of safety. However, currently there is a shortage of efficient tools to support such recording and analysis. In this study we introduce a flexible and customizable tool that allows structuring and analysis of this information. This tool has been implemented under TEEXMA®. We named our prototype TEEXMA®SAFETY. This tool provides an information management system to facilitate data collection, organization, query, analysis and reporting of accidents. A predefined information retrieval module provides ready access to data which allows the user to quickly identify the possible hazards for specific machines and provides information on the source of hazards. The main target audience for this tool includes safety personnel, accident reporters and designers. The proposed data model has been developed by analyzing different accident reports.

Locomotive crashworthiness research

DOT National Transportation Integrated Search

2015-04-01

conducts research on locomotive crashworthiness. The research approach includes four phases: : 1. Accident investigations to assemble sequences of events leading to injury and fatality. : 2. Locomotive performance is analyzed, and potential improveme...

A human factors analysis of fatal and serious injury accidents in Alaska, 2004-2009.

DOT National Transportation Integrated Search

2011-12-01

"This report summarizes the analysis of 97 general aviation accidents in Alaska that resulted in a fatality or serious : injury to one or more aircraft occupants for the years 2004-2009. The accidents were analyzed using the Human : Factors Analysis ...

Archetypes for Organisational Safety

NASA Technical Reports Server (NTRS)

Marais, Karen; Leveson, Nancy G.

2003-01-01

We propose a framework using system dynamics to model the dynamic behavior of organizations in accident analysis. Most current accident analysis techniques are event-based and do not adequately capture the dynamic complexity and non-linear interactions that characterize accidents in complex systems. In this paper we propose a set of system safety archetypes that model common safety culture flaws in organizations, i.e., the dynamic behaviour of organizations that often leads to accidents. As accident analysis and investigation tools, the archetypes can be used to develop dynamic models that describe the systemic and organizational factors contributing to the accident. The archetypes help clarify why safety-related decisions do not always result in the desired behavior, and how independent decisions in different parts of the organization can combine to impact safety.

An analysis of aircraft accidents involving fires

NASA Technical Reports Server (NTRS)

Lucha, G. V.; Robertson, M. A.; Schooley, F. A.

1975-01-01

All U. S. Air Carrier accidents between 1963 and 1974 were studied to assess the extent of total personnel and aircraft damage which occurred in accidents and in accidents involving fire. Published accident reports and NTSB investigators' factual backup files were the primary sources of data. Although it was frequently not possible to assess the relative extent of fire-caused damage versus impact damage using the available data, the study established upper and lower bounds for deaths and damage due specifically to fire. In 12 years there were 122 accidents which involved airframe fires. Eighty-seven percent of the fires occurred after impact, and fuel leakage from ruptured tanks or severed lines was the most frequently cited cause. A cost analysis was performed for 300 serious accidents, including 92 serious accidents which involved fire. Personal injury costs were outside the scope of the cost analysis, but data on personnel injury judgements as well as settlements received from the CAB are included for reference.

Construction industry accidents in Spain.

PubMed

Camino López, Miguel A; Ritzel, Dale O; Fontaneda, Ignacio; González Alcantara, Oscar J

2008-01-01

This paper analyzed industrial accidents that take place on construction sites and their severity. Eighteen variables were studied. We analyzed the influence of each of these with respect to the severity and fatality of the accident. This descriptive analysis was grounded in 1,630,452 accidents, representing the total number of accidents suffered by workers in the construction sector in Spain over the period 1990-2000. It was shown that age, type of contract, time of accident, length of service in the company, company size, day of the week, and the remainder of the variables under analysis influenced the seriousness of the accident. IMPACT ON INJURY PREVENTION: The results obtained show that different training was needed, depending on the severity of accidents, for different age, length of service in the company, organization of work, and time when workers work. The research provides an insight to the likely causes of construction injuries in Spain. As a result of the analysis, industries and governmental agencies in Spain can start to provide appropriate strategies and training to the construction workers.

A study on industrial accident rate forecasting and program development of estimated zero accident time in Korea.

PubMed

Kim, Tae-gu; Kang, Young-sig; Lee, Hyung-won

2011-01-01

To begin a zero accident campaign for industry, the first thing is to estimate the industrial accident rate and the zero accident time systematically. This paper considers the social and technical change of the business environment after beginning the zero accident campaign through quantitative time series analysis methods. These methods include sum of squared errors (SSE), regression analysis method (RAM), exponential smoothing method (ESM), double exponential smoothing method (DESM), auto-regressive integrated moving average (ARIMA) model, and the proposed analytic function method (AFM). The program is developed to estimate the accident rate, zero accident time and achievement probability of an efficient industrial environment. In this paper, MFC (Microsoft Foundation Class) software of Visual Studio 2008 was used to develop a zero accident program. The results of this paper will provide major information for industrial accident prevention and be an important part of stimulating the zero accident campaign within all industrial environments.

An analysis of pilot error-related aircraft accidents

NASA Technical Reports Server (NTRS)

Kowalsky, N. B.; Masters, R. L.; Stone, R. B.; Babcock, G. L.; Rypka, E. W.

1974-01-01

A multidisciplinary team approach to pilot error-related U.S. air carrier jet aircraft accident investigation records successfully reclaimed hidden human error information not shown in statistical studies. New analytic techniques were developed and applied to the data to discover and identify multiple elements of commonality and shared characteristics within this group of accidents. Three techniques of analysis were used: Critical element analysis, which demonstrated the importance of a subjective qualitative approach to raw accident data and surfaced information heretofore unavailable. Cluster analysis, which was an exploratory research tool that will lead to increased understanding and improved organization of facts, the discovery of new meaning in large data sets, and the generation of explanatory hypotheses. Pattern recognition, by which accidents can be categorized by pattern conformity after critical element identification by cluster analysis.

The accident analysis of mobile mine machinery in Indian opencast coal mines.

PubMed

Kumar, R; Ghosh, A K

2014-01-01

This paper presents the analysis of large mining machinery related accidents in Indian opencast coal mines. The trends of coal production, share of mining methods in production, machinery deployment in open cast mines, size and population of machinery, accidents due to machinery, types and causes of accidents have been analysed from the year 1995 to 2008. The scrutiny of accidents during this period reveals that most of the responsible factors are machine reversal, haul road design, human fault, operator's fault, machine fault, visibility and dump design. Considering the types of machines, namely, dumpers, excavators, dozers and loaders together the maximum number of fatal accidents has been caused by operator's faults and human faults jointly during the period from 1995 to 2008. The novel finding of this analysis is that large machines with state-of-the-art safety system did not reduce the fatal accidents in Indian opencast coal mines.

Aircraft accidents : method of analysis

NASA Technical Reports Server (NTRS)

1931-01-01

The revised report includes the chart for the analysis of aircraft accidents, combining consideration of the immediate causes, underlying causes, and results of accidents, as prepared by the special committee, with a number of the definitions clarified. A brief statement of the organization and work of the special committee and of the Committee on Aircraft Accidents; and statistical tables giving a comparison of the types of accidents and causes of accidents in the military services on the one hand and in civil aviation on the other, together with explanations of some of the important differences noted in these tables.

Key findings and remaining questions in the areas of core-concrete interaction and debris coolability

DOE PAGES

Farmer, M. T.; Gerardi, C.; Bremer, N.; ...

2016-10-31

The reactor accidents at Fukushima-Dai-ichi have rekindled interest in late phase severe accident behavior involving reactor pressure vessel breach and discharge of molten core melt into the containment. Two technical issues of interest in this area include core-concrete interaction and the extent to which the core debris may be quenched and rendered coolable by top flooding. The OECD-sponsored Melt Coolability and Concrete Interaction (MCCI) programs at Argonne National Laboratory included the conduct of large scale reactor material experiments and associated analysis with the objectives of resolving the ex-vessel debris coolability issue, and to address remaining uncertainties related to long-term two-dimensionalmore » molten core-concrete interactions under both wet and dry cavity conditions. These tests provided a broad database to support accident management planning, as well as the development and validation of models and codes that can be used to extrapolate the experiment results to plant conditions. This paper provides a high level overview of the key experiment results obtained during the program. Finally, a discussion is also provided that describes technical gaps that remain in this area, several of which have arisen based on the sequence of events and operator actions during Fukushima.« less

Key findings and remaining questions in the areas of core-concrete interaction and debris coolability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, M. T.; Gerardi, C.; Bremer, N.

The reactor accidents at Fukushima-Dai-ichi have rekindled interest in late phase severe accident behavior involving reactor pressure vessel breach and discharge of molten core melt into the containment. Two technical issues of interest in this area include core-concrete interaction and the extent to which the core debris may be quenched and rendered coolable by top flooding. The OECD-sponsored Melt Coolability and Concrete Interaction (MCCI) programs at Argonne National Laboratory included the conduct of large scale reactor material experiments and associated analysis with the objectives of resolving the ex-vessel debris coolability issue, and to address remaining uncertainties related to long-term two-dimensionalmore » molten core-concrete interactions under both wet and dry cavity conditions. These tests provided a broad database to support accident management planning, as well as the development and validation of models and codes that can be used to extrapolate the experiment results to plant conditions. This paper provides a high level overview of the key experiment results obtained during the program. Finally, a discussion is also provided that describes technical gaps that remain in this area, several of which have arisen based on the sequence of events and operator actions during Fukushima.« less

Modeling of local steam condensation on walls in presence of non-condensable gases. Application to a loca calculation in reactor containment using the multidimensional geyser/tonus code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benet, L.V.; Caroli, C.; Cornet, P.

1995-09-01

This paper reports part of a study of possible severe pressurized water reactor (PWR) accidents. The need for containment modeling, and in particular for a hydrogen risk study, was reinforced in France after 1990, with the requirement that severe accidents must be taken into account in the design of future plants. This new need of assessing the transient local hydrogen concentration led to the development, in the Mechanical Engineering and Technology Department of the French Atomic Energy Commission (CEA/DMT), of the multidimensional code GEYSER/TONUS for containment analysis. A detailed example of the use of this code is presented. The mixturemore » consisted of noncondensable gases (air or air plus hydrogen) and water vapor and liquid water. This is described by a compressible homogeneous two-phase flow model and wall condensation is based on the Chilton-Colburn formula and the analogy between heat and mass transfer. Results are given for a transient two-dimensional axially-symmetric computation for the first hour of a simplified accident sequence. In this there was an initial injection of a large amount of water vapor followed by a smaller amount and by hydrogen injection.« less

Application of Faecalibacterium 16S rDNA genetic marker for accurate identification of duck faeces.

PubMed

Sun, Da; Duan, Chuanren; Shang, Yaning; Ma, Yunxia; Tan, Lili; Zhai, Jun; Gao, Xu; Guo, Jingsong; Wang, Guixue

2016-04-01

The aim of this study was to judge the legal duty of pollution liabilities by assessing a duck faeces-specific marker, which can exclude distractions of residual bacteria from earlier contamination accidents. With the gene sequencing technology and bioinformatics method, we completed the comparative analysis of Faecalibacterium sequences, which were associated with ducks and other animal species, and found the sequences unique to duck faeces. Polymerase chain reaction (PCR) and agarose gel electrophoresis techniques were used to verify the reliability of both human and duck faeces-specific primers. The duck faeces-specific primers generated an amplicon of 141 bp from 43.3 % of duck faecal samples, 0 % of control samples and 100 % of sewage wastewater samples that contained duck faeces. We present here the initial evidence of Faecalibacterium-based applicability as human faeces-specificity in China. Meanwhile, this study represents the initial report of a Faecalibacterium marker for duck faeces and suggests an independent or supplementary environmental biotechnology of microbial source tracking (MST).

Organizational influence on the occurrence of work accidents involving exposure to biological material.

PubMed

Marziale, Maria Helena Palucci; Rocha, Fernanda Ludmilla Rossi; Robazzi, Maria Lúcia do Carmo Cruz; Cenzi, Camila Maria; dos Santos, Heloisa Ehmke Cardoso; Trovó, Marli Elisa Mendes

2013-01-01

to analyze work accidents involving exposure to biological materials which took place among personnel working in nursing and to evaluate the influence of the organizational culture on the occurrence of these accidents. a retrospective, analytical study, carried out in two stages in a hospital that was part of the Network for the Prevention of Work Accidents. The first stage involved the analysis of the characteristics of the work accidents involving exposure to biological materials as recorded over a seven-year period by the nursing staff in the hospital studied, and registered in the Network databank. The second stage involved the analysis of 122 nursing staff members' perception of the institutional culture, who were allocated to the control group (workers who had not had an accident) and the case group (workers who had had an accident). 386 accidents had been recorded: percutaneous lesions occurred in 79% of the cases, needles were the materials involved in 69.7% of the accidents, and in 81.9% of the accident there was contact with blood. Regarding the influence of the organizational culture on the occurrence of accidents, the results obtained through the analysis of the two groups did not demonstrate significant differences between the average scores attributed by the workers in each organizational value or practice category. It is concluded that accidents involving exposure to biological material need to be avoided, however, it was not possible to confirm the influence of organizational values or practices on workers' behavior concerning the occurrence of these accidents.

Analysis on Dangerous Source of Large Safety Accident in Storage Tank Area

NASA Astrophysics Data System (ADS)

Wang, Tong; Li, Ying; Xie, Tiansheng; Liu, Yu; Zhu, Xueyuan

2018-01-01

The difference between a large safety accident and a general accident is that the consequences of a large safety accident are particularly serious. To study the tank area which factors directly or indirectly lead to the occurrence of large-sized safety accidents. According to the three kinds of hazard source theory and the consequence cause analysis of the super safety accident, this paper analyzes the dangerous source of the super safety accident in the tank area from four aspects, such as energy source, large-sized safety accident reason, management missing, environmental impact Based on the analysis of three kinds of hazard sources and environmental analysis to derive the main risk factors and the AHP evaluation model is established, and after rigorous and scientific calculation, the weights of the related factors in four kinds of risk factors and each type of risk factors are obtained. The result of analytic hierarchy process shows that management reasons is the most important one, and then the environmental factors and the direct cause and Energy source. It should be noted that although the direct cause is relatively low overall importance, the direct cause of Failure of emergency measures and Failure of prevention and control facilities in greater weight.

Systems-based accident analysis in the led outdoor activity domain: application and evaluation of a risk management framework.

PubMed

Salmon, P; Williamson, A; Lenné, M; Mitsopoulos-Rubens, E; Rudin-Brown, C M

2010-08-01

Safety-compromising accidents occur regularly in the led outdoor activity domain. Formal accident analysis is an accepted means of understanding such events and improving safety. Despite this, there remains no universally accepted framework for collecting and analysing accident data in the led outdoor activity domain. This article presents an application of Rasmussen's risk management framework to the analysis of the Lyme Bay sea canoeing incident. This involved the development of an Accimap, the outputs of which were used to evaluate seven predictions made by the framework. The Accimap output was also compared to an analysis using an existing model from the led outdoor activity domain. In conclusion, the Accimap output was found to be more comprehensive and supported all seven of the risk management framework's predictions, suggesting that it shows promise as a theoretically underpinned approach for analysing, and learning from, accidents in the led outdoor activity domain. STATEMENT OF RELEVANCE: Accidents represent a significant problem within the led outdoor activity domain. This article presents an evaluation of a risk management framework that can be used to understand such accidents and to inform the development of accident countermeasures and mitigation strategies for the led outdoor activity domain.

Type airman certification as related to accidents.

DOT National Transportation Integrated Search

1967-10-01

An analysis of 1964 aircraft accidents, using type of airman certificate as a measure of pilot proficiency, is presented. Data show that student pilots generally have a better accident record than any other of the certification groups. Analysis confi...

Upon the reconstruction of accidents triggered by tire explosion. Analytical model and case study

NASA Astrophysics Data System (ADS)

Gaiginschi, L.; Agape, I.; Talif, S.

2017-10-01

Accident Reconstruction is important in the general context of increasing road traffic safety. In the casuistry of traffic accidents, those caused by tire explosions are critical under the severity of consequences, because they are usually happening at high speeds. Consequently, the knowledge of the running speed of the vehicle involved at the time of the tire explosion is essential to elucidate the circumstances of the accident. The paper presents an analytical model for the kinematics of a vehicle which, after the explosion of one of its tires, begins to skid, overturns and rolls. The model consists of two concurent approaches built as applications of the momentum conservation and energy conservation principles, and allows determination of the initial speed of the vehicle involved, by running backwards the sequences of the road event. The authors also aimed to both validate the two distinct analytical approaches by calibrating the calculation algorithms on a case study

The impact of young drivers' lifestyle on their road traffic accident risk in greater Athens area.

PubMed

Chliaoutakis, J E; Darviri, C; Demakakos, P T

1999-11-01

Young drivers (18-24) both in Greece and elsewhere appear to have high rates of road traffic accidents. Many factors contribute to the creation of these high road traffic accidents rates. It has been suggested that lifestyle is an important one. The main objective of this study is to find out and clarify the (potential) relationship between young drivers' lifestyle and the road traffic accident risk they face. Moreover, to examine if all the youngsters have the same elevated risk on the road or not. The sample consisted of 241 young Greek drivers of both sexes. The statistical analysis included factor analysis and logistic regression analysis. Through the principal component analysis a ten factor scale was created which included the basic lifestyle traits of young Greek drivers. The logistic regression analysis showed that the young drivers whose dominant lifestyle trait is alcohol consumption or drive without destination have high accident risk, while these whose dominant lifestyle trait is culture, face low accident risk. Furthermore, young drivers who are religious in one way or another seem to have low accident risk. Finally, some preliminary observations on how health promotion should be put into practice are discussed.

Traits and causes of environmental loss-related chemical accidents in China based on co-word analysis.

PubMed

Wu, Desheng; Song, Yu; Xie, Kefan; Zhang, Baofeng

2018-04-25

Chemical accidents are major causes of environmental losses and have been debated due to the potential threat to human beings and environment. Compared with the single statistical analysis, co-word analysis of chemical accidents illustrates significant traits at various levels and presents data into a visual network. This study utilizes a co-word analysis of the keywords extracted from the Web crawling texts of environmental loss-related chemical accidents and uses the Pearson's correlation coefficient to examine the internal attributes. To visualize the keywords of the accidents, this study carries out a multidimensional scaling analysis applying PROXSCAL and centrality identification. The research results show that an enormous environmental cost is exacted, especially given the expected environmental loss-related chemical accidents with geographical features. Meanwhile, each event often brings more than one environmental impact. Large number of chemical substances are released in the form of solid, liquid, and gas, leading to serious results. Eight clusters that represent the traits of these accidents are formed, including "leakage," "poisoning," "explosion," "pipeline crack," "river pollution," "dust pollution," "emission," and "industrial effluent." "Explosion" and "gas" possess a strong correlation with "poisoning," located at the center of visualization map.

Accident models for two-lane rural roads : segments and intersections

DOT National Transportation Integrated Search

1998-10-01

This report is a direct step for the implementation of the Accident Analysis Module in the Interactive Highway Safety Design Model (IHSDM). The Accident Analysis Module is expected to estimate the safety of two-lane rural highway characteristics for ...

Analysis of traffic accident data in Kentucky (1994-1998)

DOT National Transportation Integrated Search

1999-09-01

This report includes an analysis of traffic accident data in Kentucky for the years of 1994 through 1998. A primary objective of this study was to determine average accident statistics for Kentucky highways. Average and critical numbers and rates of ...

Estimating the causes of traffic accidents using logistic regression and discriminant analysis.

PubMed

Karacasu, Murat; Ergül, Barış; Altin Yavuz, Arzu

2014-01-01

Factors that affect traffic accidents have been analysed in various ways. In this study, we use the methods of logistic regression and discriminant analysis to determine the damages due to injury and non-injury accidents in the Eskisehir Province. Data were obtained from the accident reports of the General Directorate of Security in Eskisehir; 2552 traffic accidents between January and December 2009 were investigated regarding whether they resulted in injury. According to the results, the effects of traffic accidents were reflected in the variables. These results provide a wealth of information that may aid future measures toward the prevention of undesired results.

[Analysis of work accidents during the years 1999-2006 in a hospital company in Lombardia].

PubMed

Melloni, P; Antoniazzi, E; Somenzi, V; Galli, L; Fazioli, R; Mottinelli, A; Franzosi, C; Cirla, A M; Gobba, E

2007-01-01

This study describe accidents occurred in the period between 1999 and 2006 in the Hospital of Cremona, in which about 2400 subjects operate. The analysis of Accident Register showed a reduction of about 30% of the total number of accidents during the examined period and a non homogeneous distribution of the various types of accidents. The most frequent accidents were prick (25.8%), trauma (22.9%) and "in itinere" accidents (7.8%). One type of accident has been little considered up to now: the aggressions. Professional nurses were the most frequently involved and the most affected units were those that belong to the Internal Medicine Department. "In itinere" accidents had the longest average prognosis (11.6 days). The repetition of accidents occurred to the same operator hasn't been analysed before now: a professional nurse had nine accidents (of various type) in the seven years considered. Probably the reduction of accident must be attributed to the effectiveness of the prevention activities undertaken during the reviewed period. Biological accidents, for which it was possible to implement prevention programs, have been markedly reduced; it was not the same for "In Itinere" accidents, that depend significantly on external factors that are not easily dismissed.

[Proposal of a method for collective analysis of work-related accidents in the hospital setting].

PubMed

Osório, Claudia; Machado, Jorge Mesquita Huet; Minayo-Gomez, Carlos

2005-01-01

The article presents a method for the analysis of work-related accidents in hospitals, with the double aim of analyzing accidents in light of actual work activity and enhancing the vitality of the various professions that comprise hospital work. This process involves both research and intervention, combining knowledge output with training of health professionals, fostering expanded participation by workers in managing their daily work. The method consists of stimulating workers to recreate the situation in which a given accident occurred, shifting themselves to the position of observers of their own work. In the first stage of analysis, workers are asked to show the work analyst how the accident occurred; in the second stage, the work accident victim and analyst jointly record the described series of events in a diagram; in the third, the resulting record is re-discussed and further elaborated; in the fourth, the work accident victim and analyst evaluate and implement measures aimed to prevent the accident from recurring. The article concludes by discussing the method's possibilities and limitations in the hospital setting.

NASA's Accident Precursor Analysis Process and the International Space Station

NASA Technical Reports Server (NTRS)

Groen, Frank; Lutomski, Michael

2010-01-01

This viewgraph presentation reviews the implementation of Accident Precursor Analysis (APA), as well as the evaluation of In-Flight Investigations (IFI) and Problem Reporting and Corrective Action (PRACA) data for the identification of unrecognized accident potentials on the International Space Station.

Preliminary analysis of the National Crash Severity Study : factors in fatal accidents

DOT National Transportation Integrated Search

1979-06-01

This study investigates the fatalities on the National Crash Severity Study (NCSS) of towaway, passenger car accidents. The analysis is in three stages. First, NCSS fatalities are compared to the fatally-injured occupants reported on the Fatal Accide...

Analysis of traffic accident data in Kentucky (1986-1990)

DOT National Transportation Integrated Search

1991-09-01

This report includes an analysis of traffic accident data in Kentucky for the years of 1986-1990. A primary objectve of this study was to determine average statistics for kentucky highways. Average and critical number and rates of accidents were calc...

10 CFR 963.13 - Preclosure suitability evaluation method.

Code of Federal Regulations, 2011 CFR

2011-01-01

... to evaluate whether the geologic repository is likely to comply with the applicable radiation... prevent or mitigate the effects of postulated Category 1 and 2 event sequences. The preclosure safety... prevent accidents. ...

Qualification of safety-related electrical equipment in France. Methods, approach and test facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raimondo, E.; Capman, J.L.; Herovard, M.

1985-05-01

Requirements for qualification of electrical equipment used in French-built nuclear power plants are stated in a national code, the RCC-E, or Regles de Construction et de Conception des Materiels Electriques. Under the RCC-E, safety related equipment is assigned to one of three different categories, according to location in the plant and anticipated normal, accident and post-accident behavior. Qualification tests differ for each category and procedures range in scope from the standard seismic test to the highly stringent VISA program, which specifies a predetermined sequence of aging, radiation, seismic and simulated accident testing. A network of official French test facilities wasmore » developed specifically to meet RCC-E requirements.« less

An association between dietary habits and traffic accidents in patients with chronic liver disease: A data-mining analysis

PubMed Central

KAWAGUCHI, TAKUMI; SUETSUGU, TAKURO; OGATA, SHYOU; IMANAGA, MINAMI; ISHII, KUMIKO; ESAKI, NAO; SUGIMOTO, MASAKO; OTSUYAMA, JYURI; NAGAMATSU, AYU; TANIGUCHI, EITARO; ITOU, MINORU; ORIISHI, TETSUHARU; IWASAKI, SHOKO; MIURA, HIROKO; TORIMURA, TAKUJI

2016-01-01

The incidence of traffic accidents in patients with chronic liver disease (CLD) is high in the USA. However, the characteristics of patients, including dietary habits, differ between Japan and the USA. The present study investigated the incidence of traffic accidents in CLD patients and the clinical profiles associated with traffic accidents in Japan using a data-mining analysis. A cross-sectional study was performed and 256 subjects [148 CLD patients (CLD group) and 106 patients with other digestive diseases (disease control group)] were enrolled; 2 patients were excluded. The incidence of traffic accidents was compared between the two groups. Independent factors for traffic accidents were analyzed using logistic regression and decision-tree analyses. The incidence of traffic accidents did not differ between the CLD and disease control groups (8.8 vs. 11.3%). The results of the logistic regression analysis showed that yoghurt consumption was the only independent risk factor for traffic accidents (odds ratio, 0.37; 95% confidence interval, 0.16–0.85; P=0.0197). Similarly, the results of the decision-tree analysis showed that yoghurt consumption was the initial divergence variable. In patients who consumed yoghurt habitually, the incidence of traffic accidents was 6.6%, while that in patients who did not consume yoghurt was 16.0%. CLD was not identified as an independent factor in the logistic regression and decision-tree analyses. In conclusion, the difference in the incidence of traffic accidents in Japan between the CLD and disease control groups was insignificant. Furthermore, yoghurt consumption was an independent negative risk factor for traffic accidents in patients with digestive diseases, including CLD. PMID:27123257

An association between dietary habits and traffic accidents in patients with chronic liver disease: A data-mining analysis.

PubMed

Kawaguchi, Takumi; Suetsugu, Takuro; Ogata, Shyou; Imanaga, Minami; Ishii, Kumiko; Esaki, Nao; Sugimoto, Masako; Otsuyama, Jyuri; Nagamatsu, Ayu; Taniguchi, Eitaro; Itou, Minoru; Oriishi, Tetsuharu; Iwasaki, Shoko; Miura, Hiroko; Torimura, Takuji

2016-05-01

The incidence of traffic accidents in patients with chronic liver disease (CLD) is high in the USA. However, the characteristics of patients, including dietary habits, differ between Japan and the USA. The present study investigated the incidence of traffic accidents in CLD patients and the clinical profiles associated with traffic accidents in Japan using a data-mining analysis. A cross-sectional study was performed and 256 subjects [148 CLD patients (CLD group) and 106 patients with other digestive diseases (disease control group)] were enrolled; 2 patients were excluded. The incidence of traffic accidents was compared between the two groups. Independent factors for traffic accidents were analyzed using logistic regression and decision-tree analyses. The incidence of traffic accidents did not differ between the CLD and disease control groups (8.8 vs. 11.3%). The results of the logistic regression analysis showed that yoghurt consumption was the only independent risk factor for traffic accidents (odds ratio, 0.37; 95% confidence interval, 0.16-0.85; P=0.0197). Similarly, the results of the decision-tree analysis showed that yoghurt consumption was the initial divergence variable. In patients who consumed yoghurt habitually, the incidence of traffic accidents was 6.6%, while that in patients who did not consume yoghurt was 16.0%. CLD was not identified as an independent factor in the logistic regression and decision-tree analyses. In conclusion, the difference in the incidence of traffic accidents in Japan between the CLD and disease control groups was insignificant. Furthermore, yoghurt consumption was an independent negative risk factor for traffic accidents in patients with digestive diseases, including CLD.

Analysis of traffic accident data in Kentucky (1995-1999)

DOT National Transportation Integrated Search

2000-09-01

This report includes an analysis of traffic accidents data in Kentucky for the year 1995-1999. A primary objective of this study was to determined average and critical numbers and rates of accidents for various types of highways in rural and urban ar...

Accident Analysis for the NIST Research Reactor Before and After Fuel Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baek J.; Diamond D.; Cuadra, A.

Postulated accidents have been analyzed for the 20 MW D2O-moderated research reactor (NBSR) at the National Institute of Standards and Technology (NIST). The analysis has been carried out for the present core, which contains high enriched uranium (HEU) fuel and for a proposed equilibrium core with low enriched uranium (LEU) fuel. The analyses employ state-of-the-art calculational methods. Three-dimensional Monte Carlo neutron transport calculations were performed with the MCNPX code to determine homogenized fuel compositions in the lower and upper halves of each fuel element and to determine the resulting neutronic properties of the core. The accident analysis employed a modelmore » of the primary loop with the RELAP5 code. The model includes the primary pumps, shutdown pumps outlet valves, heat exchanger, fuel elements, and flow channels for both the six inner and twenty-four outer fuel elements. Evaluations were performed for the following accidents: (1) control rod withdrawal startup accident, (2) maximum reactivity insertion accident, (3) loss-of-flow accident resulting from loss of electrical power with an assumption of failure of shutdown cooling pumps, (4) loss-of-flow accident resulting from a primary pump seizure, and (5) loss-of-flow accident resulting from inadvertent throttling of a flow control valve. In addition, natural circulation cooling at low power operation was analyzed. The analysis shows that the conversion will not lead to significant changes in the safety analysis and the calculated minimum critical heat flux ratio and maximum clad temperature assure that there is adequate margin to fuel failure.« less

'Remixing Rasmussen': The evolution of Accimaps within systemic accident analysis.

PubMed

Waterson, Patrick; Jenkins, Daniel P; Salmon, Paul M; Underwood, Peter

2017-03-01

Throughout Jens Rasmussen's career there has been a continued emphasis on the development of methods, techniques and tools for accident analysis and investigation. In this paper we focus on the evolution and development of one specific example, namely Accimaps and their use for accident analysis. We describe the origins of Accimaps followed by a review of 27 studies which have applied and adapted Accimaps over the period 2000-2015 to a range of domains and types of accident. Aside from demonstrating the versatility and popularity of the method, part of the motivation for the review of the use of Accimaps is to address the question of what constitutes a sound, usable, valid and reliable approach to systemic accident analysis. The findings from the review demonstrate continuity with the work carried out by Rasmussen, as well as significant variation (e.g., changes to the Accimap, used of additional theoretical and practice-oriented perspectives on safety). We conclude the paper with some speculations regarding future extension and adaptation of the Accimap approach including the possibility of using hybrid models for accident analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Methodology, status and plans for development and assessment of the code ATHLET

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teschendorff, V.; Austregesilo, H.; Lerchl, G.

1997-07-01

The thermal-hydraulic computer code ATHLET (Analysis of THermal-hydraulics of LEaks and Transients) is being developed by the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) for the analysis of anticipated and abnormal plant transients, small and intermediate leaks as well as large breaks in light water reactors. The aim of the code development is to cover the whole spectrum of design basis and beyond design basis accidents (without core degradation) for PWRs and BWRs with only one code. The main code features are: advanced thermal-hydraulics; modular code architecture; separation between physical models and numerical methods; pre- and post-processing tools; portability. The codemore » has features that are of special interest for applications to small leaks and transients with accident management, e.g. initialization by a steady-state calculation, full-range drift-flux model, dynamic mixture level tracking. The General Control Simulation Module of ATHLET is a flexible tool for the simulation of the balance-of-plant and control systems including the various operator actions in the course of accident sequences with AM measures. The code development is accompained by a systematic and comprehensive validation program. A large number of integral experiments and separate effect tests, including the major International Standard Problems, have been calculated by GRS and by independent organizations. The ATHLET validation matrix is a well balanced set of integral and separate effects tests derived from the CSNI proposal emphasizing, however, the German combined ECC injection system which was investigated in the UPTF, PKL and LOBI test facilities.« less

Insights Gained from Forensic Analysis with MELCOR of the Fukushima-Daiichi Accidents.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrews, Nathan C.; Gauntt, Randall O.

Since the accidents at Fukushima-Daiichi, Sandia National Laboratories has been modeling these accident scenarios using the severe accident analysis code, MELCOR. MELCOR is a widely used computer code developed at Sandia National Laboratories since ~1982 for the U.S. Nuclear Regulatory Commission. Insights from the modeling of these accidents is being used to better inform future code development and potentially improved accident management. To date, our necessity to better capture in-vessel thermal-hydraulic and ex-vessel melt coolability and concrete interactions has led to the implementation of new models. The most recent analyses, presented in this paper, have been in support of themore » of the Organization for Economic Cooperation and Development Nuclear Energy Agency’s (OECD/NEA) Benchmark Study of the Accident at the Fukushima Daiichi Nuclear Power Station (BSAF) Project. The goal of this project is to accurately capture the source term from all three releases and then model the atmospheric dispersion. In order to do this, a forensic approach is being used in which available plant data and release timings is being used to inform the modeled MELCOR accident scenario. For example, containment failures, core slumping events and lower head failure timings are all enforced parameters in these analyses. This approach is fundamentally different from a blind code assessment analysis often used in standard problem exercises. The timings of these events are informed by representative spikes or decreases in plant data. The combination of improvements to the MELCOR source code resulting from analysis previous accident analysis and this forensic approach has allowed Sandia to generate representative and plausible source terms for all three accidents at Fukushima Daiichi out to three weeks after the accident to capture both early and late releases. In particular, using the source terms developed by MELCOR, the MACCS software code, which models atmospheric dispersion and deposition, we are able to reasonably capture the deposition of radionuclides to the northwest of the reactor site.« less

Reactor Safety Gap Evaluation of Accident Tolerant Components and Severe Accident Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, Mitchell T.; Bunt, R.; Corradini, M.

The overall objective of this study was to conduct a technology gap evaluation on accident tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist, given the current state of light water reactor (LWR) severe accident research, and additionally augmented by insights obtained from the Fukushima accident. The ultimate benefit of this activity is that the results can be used to refine the Department of Energy’s (DOE) Reactor Safety Technology (RST) research and development (R&D) program plan to address key knowledge gaps in severe accident phenomena and analyses that affectmore » reactor safety and that are not currently being addressed by the industry or the Nuclear Regulatory Commission (NRC).« less

Differences in Characteristics of Aviation Accidents during 1993-2012 Based on Flight Purpose

NASA Technical Reports Server (NTRS)

Evans, Joni K.

2016-01-01

Usually aviation accidents are categorized and analyzed within flight conduct rules (Part 121, Part 135, Part 91) because differences in accident rates within flight rules have been demonstrated. Even within a particular flight rule the flights have different purposes. For many, Part 121 flights are synonymous with scheduled passenger transport, and indeed this is the largest group of Part 121 accidents. But there are also non-scheduled (charter) passenger transport and cargo flights. The primary purpose of the analysis reported here is to examine the differences in aviation accidents based on the purpose of the flight. Some of the factors examined are the accident severity, aircraft characteristics and accident occurrence categories. Twenty consecutive years of data were available and utilized to complete this analysis.

Development of multivariate exposure and fatal accident involvement rates for 1977

DOT National Transportation Integrated Search

1985-10-01

The need for multivariate accident involvement rates is often encounted in : accident analysis. The FARS (Fatal Accident Reporting System) files contain : records of fatal involvements characterized by many variables while NPTS : (National Personal T...

Work-Related Accidents and Sharp Injuries in Paramedics-Illustrated with an Example of a Multi-Specialist Hospital, Located in Central Poland.

PubMed

Garus-Pakowska, Anna; Szatko, Franciszek; Ulrichs, Magdalena

2017-08-10

(1) Background: An analysis of work-related accidents in paramedics in Poland by presenting the model and trend of accidents, accident rates and by identifying causes and results of accidents; (2) Methods: A retrospective analysis of medical documentation regarding work-related accidents in a multi-specialist hospital, located in central Poland, in the period 2005-2015. The study group included paramedics who had an accident while being on duty; (3) Results: According to hospital records, 88 paramedics were involved in 390 accidents and 265 injuries caused by sharp instruments. The annual accident rate was 5.34/100 employed paramedics. Most of the accidents occurred at night. The most common reason for the accident was careless behaviour of the paramedic, which resulted in joint sprains and dislocations. Injuries accounted for a huge portion of the total number of events. As many as 45% of injuries were not officially recorded; (4) Conclusion: High rates of work-related accidents and injuries caused by sharp instruments in paramedics are a serious public health problem. Further studies should be conducted in order to identify risk factors of accidents, particularly injuries, and to implement preventative programmes, aiming to minimise rates of occupational hazards for paramedics.

Work-Related Accidents and Sharp Injuries in Paramedics—Illustrated with an Example of a Multi-Specialist Hospital, Located in Central Poland

PubMed Central

Szatko, Franciszek; Ulrichs, Magdalena

2017-01-01

(1) Background: An analysis of work-related accidents in paramedics in Poland by presenting the model and trend of accidents, accident rates and by identifying causes and results of accidents; (2) Methods: A retrospective analysis of medical documentation regarding work-related accidents in a multi-specialist hospital, located in central Poland, in the period 2005–2015. The study group included paramedics who had an accident while being on duty; (3) Results: According to hospital records, 88 paramedics were involved in 390 accidents and 265 injuries caused by sharp instruments. The annual accident rate was 5.34/100 employed paramedics. Most of the accidents occurred at night. The most common reason for the accident was careless behaviour of the paramedic, which resulted in joint sprains and dislocations. Injuries accounted for a huge portion of the total number of events. As many as 45% of injuries were not officially recorded; (4) Conclusion: High rates of work-related accidents and injuries caused by sharp instruments in paramedics are a serious public health problem. Further studies should be conducted in order to identify risk factors of accidents, particularly injuries, and to implement preventative programmes, aiming to minimise rates of occupational hazards for paramedics. PMID:28796193

Utilization of accident databases and fuzzy sets to estimate frequency of HazMat transport accidents.

PubMed

Qiao, Yuanhua; Keren, Nir; Mannan, M Sam

2009-08-15

Risk assessment and management of transportation of hazardous materials (HazMat) require the estimation of accident frequency. This paper presents a methodology to estimate hazardous materials transportation accident frequency by utilizing publicly available databases and expert knowledge. The estimation process addresses route-dependent and route-independent variables. Negative binomial regression is applied to an analysis of the Department of Public Safety (DPS) accident database to derive basic accident frequency as a function of route-dependent variables, while the effects of route-independent variables are modeled by fuzzy logic. The integrated methodology provides the basis for an overall transportation risk analysis, which can be used later to develop a decision support system.

Major differences in rates of occupational accidents between different nationalities of seafarers.

PubMed

Hansen, Henrik L; Laursen, Lise Hedgaard; Frydberg, Morten; Kristensen, Soeren

2008-01-01

Earlier studies and statistics have shown that merchant seafarers from the South East Asia had considerable lower accident rates when compared with seafarers from Western Europe. The purposes of the study were to investigate whether the earlier observations were sustained if further sources on occurrence of accidents were used and to identify specific causes of excess accident rates among certain nationalities. Occupational accidents aboard Danish merchant ships during one year were identified from four different sources. These included accidents reported to the maritime authorities, accidents reported to a mutual insurance company, files on medical costs reimbursed by the government and finally, accidents in which there has been contact to the radio medical service. Time at risk aboard was obtained from a register on all employment periods aboard merchant ships. A total of 943 accidents causing personal injury to a seafarer directly caused by work aboard were identified. Among these accidents, 499 had taken place aboard cargo ships in international trade. Only these were used in the detailed analysis. The accident rate for all identified accidents aboard cargo ships were 84 accidents per 1,000 years aboard. The crude incidence rate ratio (IRR) for East European seafarers was 0.88 and for South East Asians 0.38 using West European seafarers as reference. In a Poisson regression analysis, the IRR for South East Asians was 0.29 (0.22-0.38). In an analysis including only more serious accidents, IRR for South East Asians rose to 0.36 (0.26-0.48). This study indicates that seafarers from South East Asia, mainly the Philippines, may have a genuine lower risk of occupational accidents in comparison with seafarers from Western and Eastern Europe. Differences in approach to safety and risk taking between South East Asian and European seafarers should be identified and positives attitudes included in accident preventing programmes. Main messages Seafarers from South East Asia, mainly the Philippines, seem to have a genuine lower risk of occupational accidents in comparison with seafarers from Western and Eastern Europe. Differences in approach to safety and risk taking between South East Asian and European seafarers should be identified and positives attitudes included in accident preventing programmes.

An analysis of urban collisions using an artificial intelligence model.

PubMed

Mussone, L; Ferrari, A; Oneta, M

1999-11-01

Traditional studies on road accidents estimate the effect of variables (such as vehicular flows, road geometry, vehicular characteristics), and the calculation of the number of accidents. A descriptive statistical analysis of the accidents (those used in the model) over the period 1992-1995 is proposed. The paper describes an alternative method based on the use of artificial neural networks (ANN) in order to work out a model that relates to the analysis of vehicular accidents in Milan. The degree of danger of urban intersections using different scenarios is quantified by the ANN model. Methodology is the first result, which allows us to tackle the modelling of urban vehicular accidents by the innovative use of ANN. Other results deal with model outputs: intersection complexity may determine a higher accident index depending on the regulation of intersection. The highest index for running over of pedestrian occurs at non-signalised intersections at night-time.

Accidents at work and costs analysis: a field study in a large Italian company.

PubMed

Battaglia, Massimo; Frey, Marco; Passetti, Emilio

2014-01-01

Accidents at work are still a heavy burden in social and economic terms, and action to improve health and safety standards at work offers great potential gains not only to employers, but also to individuals and society as a whole. However, companies often are not interested to measure the costs of accidents even if cost information may facilitate preventive occupational health and safety management initiatives. The field study, carried out in a large Italian company, illustrates technical and organisational aspects associated with the implementation of an accident costs analysis tool. The results indicate that the implementation (and the use) of the tool requires a considerable commitment by the company, that accident costs analysis should serve to reinforce the importance of health and safety prevention and that the economic dimension of accidents is substantial. The study also suggests practical ways to facilitate the implementation and the moral acceptance of the accounting technology.

Accidents at Work and Costs Analysis: A Field Study in a Large Italian Company

PubMed Central

BATTAGLIA, Massimo; FREY, Marco; PASSETTI, Emilio

2014-01-01

Accidents at work are still a heavy burden in social and economic terms, and action to improve health and safety standards at work offers great potential gains not only to employers, but also to individuals and society as a whole. However, companies often are not interested to measure the costs of accidents even if cost information may facilitate preventive occupational health and safety management initiatives. The field study, carried out in a large Italian company, illustrates technical and organisational aspects associated with the implementation of an accident costs analysis tool. The results indicate that the implementation (and the use) of the tool requires a considerable commitment by the company, that accident costs analysis should serve to reinforce the importance of health and safety prevention and that the economic dimension of accidents is substantial. The study also suggests practical ways to facilitate the implementation and the moral acceptance of the accounting technology. PMID:24869894

A spatial analysis of urban transit accidents assisted by Emergency Mobile Care Services: an analysis of space and time.

PubMed

Mendonça, Marcela Franklin Salvador de; Silva, Amanda Priscila de Santana Cabral; Castro, Claudia Cristina Lima de

2017-01-01

Urban transit accident are a global public health problem. The objective of this study was to describe the profile of the victims and the occurrences of urban transit accidents attended to by emergency mobile care services (Serviço de Atendimento Móvel de Urgência- SAMU) in Recife, and their distribution based on spatial analysis. An ecological study, developed through secondary data from emergency mobile care services in Recife, referring to the total number of occurrences of urban transit accidents attended to from January 1 to June 30, 2015. The spatial analysis was performed using the Moran index. Basic support units performed most of the emergency services (89.2%). Among the victims, there was a predominance of males (76.8%) and an age group of 20 - 29 years old (31.5%). Collisions were responsible for 59.9% of the transit accidents, and motorcycles for 61.6% of the accidents among all means of transportation. Friday was the day that showed the highest risk for treatment, and there was a concentration of events between 6:00 am - 8:59am and 6:00pm - 8:59pm. The MoranMap identified critical areas where calls came from traffic accidents during the period analyzed. The records of the mobile service from the spatial analysis are an important source of information for health surveillance. The spatial analysis of urban transit accidents identified regions with a positive spatial correlation, providing subsidies to the logistical planning of emergency mobile care services. This study is groundbreaking in that it offers such information about the region.

Content analysis of 100 consecutive media reports of amusement ride accidents.

PubMed

Woodcock, Kathryn

2008-01-01

Accident investigations influence public perceptions and safety management strategies by determining the amount and type of information learned about the accident. To examine the factors considered in investigations, this study used a content analysis of 100 consecutive media reports of amusement ride accidents from an online media archive. Fatalities were overrepresented in the media dataset compared with U.S. national estimates. For analysis of reports, a modified "Haddon matrix" was developed using human-factors categories. This approach was useful to show differences between the proportions and types of factors considered in the different accident stages and between employee and rider accidents. Employee injury accounts primarily referred to the employee's task and to the employee. Rider injury reports were primarily related to the ride device itself and rarely referred to the rider's "task", social influences, or the rider's own actions, and only some reference to their characteristics. Qualitatively, it was evident that more human factors analysis is required to augment scant pre-failure information about the task, social environment, and the person, to make that information available for prevention of amusement ride accidents. By design, this study reflected information reported by the media. Future work will use the same techniques with official reports.

[A spatially explicit analysis of traffic accidents involving pedestrians and cyclists in Berlin].

PubMed

Lakes, Tobia

2017-12-01

In many German cities and counties, sustainable mobility concepts that strengthen pedestrian and cyclist traffic are promoted. From the perspectives of urban development, traffic planning and public healthcare, a spatially differentiated analysis of traffic accident data is decisive. 1) The identification of spatial and temporal patterns of the distribution of accidents involving cyclists and pedestrians, 2) the identification of hotspots and exploration of possible underlying causes and 3) the critical discussion of benefits and challenges of the results and the derivation of conclusions. Spatio-temporal distributions of data from accident statistics in Berlin involving pedestrians and cyclists from 2011 to 2015 were analysed with geographic information systems (GIS). While the total number of accidents remains relatively stable for pedestrian and cyclist accidents, the spatial distribution analysis shows, however, that there are significant spatial clusters (hotspots) of traffic accidents with a strong concentration in the inner city area. In a critical discussion, the benefits of geographic concepts are identified, such as spatially explicit health data (in this case traffic accident data), the importance of the integration of other data sources for the evaluation of the health impact of areas (traffic accident statistics of the police), and the possibilities and limitations of spatial-temporal data analysis (spatial point-density analyses) for the derivation of decision-supported recommendations and for the evaluation of policy measures of health prevention and of health-relevant urban development.

Association between Daily Hospital Outpatient Visits for Accidents and Daily Ambient Air Temperatures in an Industrial City.

PubMed

Chau, Tang-Tat; Wang, Kuo-Ying

2016-01-01

An accident is an unwanted hazard to a person. However, accidents occur. In this work, we search for correlations between daily accident rates and environmental factors. To study daily hospital outpatients who were admitted for accidents during a 5-year period, 2007-2011, we analyzed data regarding 168,366 outpatients using univariate regression models; we also used multivariable regression models to account for confounding factors. Our analysis indicates that the number of male outpatients admitted for accidents was approximately 1.31 to 1.47 times the number of female outpatients (P < 0.0001). Of the 12 parameters (regarding air pollution and meteorology) considered, only daily temperature exhibited consistent and significant correlations with the daily number of hospital outpatient visits for accidents throughout the 5-year analysis period. The univariate regression models indicate that older people (greater than 66 years old) had the fewest accidents per 1-degree increase in temperature, followed by young people (0-15 years old). Middle-aged people (16-65 years old) were the group of outpatients that were more prone to accidents, with an increase in accident rates of 0.8-1.2 accidents per degree increase in temperature. The multivariable regression models also reveal that the temperature variation was the dominant factor in determining the daily number of outpatient visits for accidents. Our further multivariable model analysis of temperature with respect to air pollution variables show that, through the increases in emissions and concentrations of CO, photochemical O3 production and NO2 loss in the ambient air, increases in vehicular emissions are associated with increases in temperatures. As such, increases in hospital visits for accidents are related to vehicular emissions and usage. This finding is consistent with clinical experience which shows about 60% to 80% of accidents are related to traffic, followed by accidents occurred in work place.

Association between Daily Hospital Outpatient Visits for Accidents and Daily Ambient Air Temperatures in an Industrial City

PubMed Central

Chau, Tang-Tat; Wang, Kuo-Ying

2016-01-01

An accident is an unwanted hazard to a person. However, accidents occur. In this work, we search for correlations between daily accident rates and environmental factors. To study daily hospital outpatients who were admitted for accidents during a 5-year period, 2007–2011, we analyzed data regarding 168,366 outpatients using univariate regression models; we also used multivariable regression models to account for confounding factors. Our analysis indicates that the number of male outpatients admitted for accidents was approximately 1.31 to 1.47 times the number of female outpatients (P < 0.0001). Of the 12 parameters (regarding air pollution and meteorology) considered, only daily temperature exhibited consistent and significant correlations with the daily number of hospital outpatient visits for accidents throughout the 5-year analysis period. The univariate regression models indicate that older people (greater than 66 years old) had the fewest accidents per 1-degree increase in temperature, followed by young people (0–15 years old). Middle-aged people (16–65 years old) were the group of outpatients that were more prone to accidents, with an increase in accident rates of 0.8–1.2 accidents per degree increase in temperature. The multivariable regression models also reveal that the temperature variation was the dominant factor in determining the daily number of outpatient visits for accidents. Our further multivariable model analysis of temperature with respect to air pollution variables show that, through the increases in emissions and concentrations of CO, photochemical O3 production and NO2 loss in the ambient air, increases in vehicular emissions are associated with increases in temperatures. As such, increases in hospital visits for accidents are related to vehicular emissions and usage. This finding is consistent with clinical experience which shows about 60% to 80% of accidents are related to traffic, followed by accidents occurred in work place. PMID:26815039

Preliminary calculations related to the accident at Three Mile Island

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirchner, W.L.; Stevenson, M.G.

This report discusses preliminary studies of the Three Mile Island Unit 2 (TMI-2) accident based on available methods and data. The work reported includes: (1) a TRAC base case calculation out to 3 hours into the accident sequence; (2) TRAC parametric calculations, these are the same as the base case except for a single hypothetical change in the system conditions, such as assuming the high pressure injection (HPI) system operated as designed rather than as in the accident; (3) fuel rod cladding failure, cladding oxidation due to zirconium metal-steam reactions, hydrogen release due to cladding oxidation, cladding ballooning, cladding embrittlement,more » and subsequent cladding breakup estimates based on TRAC calculated cladding temperatures and system pressures. Some conclusions of this work are: the TRAC base case accident calculation agrees very well with known system conditions to nearly 3 hours into the accident; the parametric calculations indicate that, loss-of-core cooling was most influenced by the throttling of High-Pressure Injection (HPI) flows, given the accident initiating events and the pressurizer electromagnetic-operated valve (EMOV) failing to close as designed; failure of nearly all the rods and gaseous fission product gas release from the failed rods is predicted to have occurred at about 2 hours and 30 minutes; cladding oxidation (zirconium-steam reaction) up to 3 hours resulted in the production of approximately 40 kilograms of hydrogen.« less

23 CFR 658.11 - Additions, deletions, exceptions, and restrictions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... analysis of suitability based on the criteria in § 658.9. (2) Proposals for additions that meet the... experiencing above normal accident rates and/or accident severities? Does analysis of the accident problem..., intersection geometrics and vulnerability of roadside hardware. (5) Is there a reasonable alternate route...

Analysis of Two Electrocution Accidents in Greece that Occurred due to Unexpected Re-energization of Power Lines

PubMed Central

Baka, Aikaterini D.; Uzunoglu, Nikolaos K.

2014-01-01

Investigation and analysis of accidents are critical elements of safety management. The over-riding purpose of an organization in carrying out an accident investigation is to prevent similar accidents, as well as seek a general improvement in the management of health and safety. Hundreds of workers have suffered injuries while installing, maintaining, or servicing machinery and equipment due to sudden re-energization of power lines. This study presents and analyzes two electrical accidents (1 fatal injury and 1 serious injury) that occurred because the power supply was reconnected inadvertently or by mistake. PMID:25379331

Analysis of Two Electrocution Accidents in Greece that Occurred due to Unexpected Re-energization of Power Lines.

PubMed

Baka, Aikaterini D; Uzunoglu, Nikolaos K

2014-09-01

Investigation and analysis of accidents are critical elements of safety management. The over-riding purpose of an organization in carrying out an accident investigation is to prevent similar accidents, as well as seek a general improvement in the management of health and safety. Hundreds of workers have suffered injuries while installing, maintaining, or servicing machinery and equipment due to sudden re-energization of power lines. This study presents and analyzes two electrical accidents (1 fatal injury and 1 serious injury) that occurred because the power supply was reconnected inadvertently or by mistake.

Human error and commercial aviation accidents: an analysis using the human factors analysis and classification system.

PubMed

Shappell, Scott; Detwiler, Cristy; Holcomb, Kali; Hackworth, Carla; Boquet, Albert; Wiegmann, Douglas A

2007-04-01

The aim of this study was to extend previous examinations of aviation accidents to include specific aircrew, environmental, supervisory, and organizational factors associated with two types of commercial aviation (air carrier and commuter/ on-demand) accidents using the Human Factors Analysis and Classification System (HFACS). HFACS is a theoretically based tool for investigating and analyzing human error associated with accidents and incidents. Previous research has shown that HFACS can be reliably used to identify human factors trends associated with military and general aviation accidents. Using data obtained from both the National Transportation Safety Board and the Federal Aviation Administration, 6 pilot-raters classified aircrew, supervisory, organizational, and environmental causal factors associated with 1020 commercial aviation accidents that occurred over a 13-year period. The majority of accident causal factors were attributed to aircrew and the environment, with decidedly fewer associated with supervisory and organizational causes. Comparisons were made between HFACS causal categories and traditional situational variables such as visual conditions, injury severity, and regional differences. These data will provide support for the continuation, modification, and/or development of interventions aimed at commercial aviation safety. HFACS provides a tool for assessing human factors associated with accidents and incidents.

A qualitative study of the background and in-hospital medicolegal response to female burn injuries in India.

PubMed

Daruwalla, Nayreen; Belur, Jyoti; Kumar, Meena; Tiwari, Vinay; Sarabahi, Sujata; Tilley, Nick; Osrin, David

2014-11-30

Most burns happen in low- and middle-income countries. In India, deaths related to burns are more common in women than in men and occur against a complex background in which the cause - accidental or non-accidental, suicidal or homicidal - is often unclear. Our study aimed to understand the antecedents to burns and the problem of ascribing cause, the sequence of medicolegal events after a woman was admitted to hospital, and potential opportunities for improvement. We conducted semi-structured interviews with 33 women admitted to two major burns units, their families, and 26 key informant doctors, nurses, and police officers. We used framework analysis to examine the context in which burns occurred and the sequence of medicolegal action after admission to hospital. Interviewees described accidents, attempted suicide, and attempted homicide. Distinguishing between these was difficult because the underlying combination of poverty and cultural precedent was common to all and action was contingent on potentially conflicting narratives. Space constraint, problems with cooking equipment, and inflammable clothing increased the risk of accidental burns, but coexisted with household conflict, gender-based violence, and alcohol use. Most burns were initially ascribed to accidents. Clinicians adhered to medicolegal procedures, the police carried out their investigative requirements relatively rapidly, but both groups felt vulnerable in the face of the legal process. Women's understandable reticence to describe burns as non-accidental, the contested nature of statements, their perceived history of changeability, the limited quality and validity of forensic evidence, and the requirement for resilience on the part of clients underlay a general pessimism. The similarities between accident and intention cluster so tightly as to make them challenging to distinguish, especially given women's understandable reticence to describe burns as non-accidental. The contested status of forensic evidence and a reliance on testimony means that only a minority of cases lead to conviction. The emphasis should be on improving documentation, communication between service providers, and public understanding of the risks of burns.

Motorcycle accident cause factors and identification of countermeasures. Volume 1 : technical report

DOT National Transportation Integrated Search

1981-01-01

This report presents the data and find~ings from the on-scene, in-depth : investigations of 900 motorcycle accidents and the analysis of 3600 traffic : accident reports of motorcycle accidents in the same study area. : Comprehensive data were collect...

Motorcycle accident cause factors and identification of countermeasures. Volume 2 : appendix/supplemental data

DOT National Transportation Integrated Search

1981-01-01

This report presents the data and findings from the on-scene, in-depth : investigations of 900 motorcycle accidents and the analysis of 3600 traffic : accident reports of motorcycle accidents in the same study area. : Comprehensive data were collecte...

Spatiotemporal characteristics of elderly population’s traffic accidents in Seoul using space-time cube and space-time kernel density estimation

PubMed Central

Cho, Nahye; Son, Serin

2018-01-01

The purpose of this study is to analyze how the spatiotemporal characteristics of traffic accidents involving the elderly population in Seoul are changing by time period. We applied kernel density estimation and hotspot analyses to analyze the spatial characteristics of elderly people’s traffic accidents, and the space-time cube, emerging hotspot, and space-time kernel density estimation analyses to analyze the spatiotemporal characteristics. In addition, we analyzed elderly people’s traffic accidents by dividing cases into those in which the drivers were elderly people and those in which elderly people were victims of traffic accidents, and used the traffic accidents data in Seoul for 2013 for analysis. The main findings were as follows: (1) the hotspots for elderly people’s traffic accidents differed according to whether they were drivers or victims. (2) The hourly analysis showed that the hotspots for elderly drivers’ traffic accidents are in specific areas north of the Han River during the period from morning to afternoon, whereas the hotspots for elderly victims are distributed over a wide area from daytime to evening. (3) Monthly analysis showed that the hotspots are weak during winter and summer, whereas they are strong in the hiking and climbing areas in Seoul during spring and fall. Further, elderly victims’ hotspots are more sporadic than elderly drivers’ hotspots. (4) The analysis for the entire period of 2013 indicates that traffic accidents involving elderly people are increasing in specific areas on the north side of the Han River. We expect the results of this study to aid in reducing the number of traffic accidents involving elderly people in the future. PMID:29768453

Spatiotemporal characteristics of elderly population's traffic accidents in Seoul using space-time cube and space-time kernel density estimation.

PubMed

Kang, Youngok; Cho, Nahye; Son, Serin

2018-01-01

The purpose of this study is to analyze how the spatiotemporal characteristics of traffic accidents involving the elderly population in Seoul are changing by time period. We applied kernel density estimation and hotspot analyses to analyze the spatial characteristics of elderly people's traffic accidents, and the space-time cube, emerging hotspot, and space-time kernel density estimation analyses to analyze the spatiotemporal characteristics. In addition, we analyzed elderly people's traffic accidents by dividing cases into those in which the drivers were elderly people and those in which elderly people were victims of traffic accidents, and used the traffic accidents data in Seoul for 2013 for analysis. The main findings were as follows: (1) the hotspots for elderly people's traffic accidents differed according to whether they were drivers or victims. (2) The hourly analysis showed that the hotspots for elderly drivers' traffic accidents are in specific areas north of the Han River during the period from morning to afternoon, whereas the hotspots for elderly victims are distributed over a wide area from daytime to evening. (3) Monthly analysis showed that the hotspots are weak during winter and summer, whereas they are strong in the hiking and climbing areas in Seoul during spring and fall. Further, elderly victims' hotspots are more sporadic than elderly drivers' hotspots. (4) The analysis for the entire period of 2013 indicates that traffic accidents involving elderly people are increasing in specific areas on the north side of the Han River. We expect the results of this study to aid in reducing the number of traffic accidents involving elderly people in the future.

SOARCA Peach Bottom Atomic Power Station Long-Term Station Blackout Uncertainty Analysis: Knowledge Advancement.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gauntt, Randall O.; Mattie, Patrick D.; Bixler, Nathan E.

2014-02-01

This paper describes the knowledge advancements from the uncertainty analysis for the State-of- the-Art Reactor Consequence Analyses (SOARCA) unmitigated long-term station blackout accident scenario at the Peach Bottom Atomic Power Station. This work assessed key MELCOR and MELCOR Accident Consequence Code System, Version 2 (MACCS2) modeling uncertainties in an integrated fashion to quantify the relative importance of each uncertain input on potential accident progression, radiological releases, and off-site consequences. This quantitative uncertainty analysis provides measures of the effects on consequences, of each of the selected uncertain parameters both individually and in interaction with other parameters. The results measure the modelmore » response (e.g., variance in the output) to uncertainty in the selected input. Investigation into the important uncertain parameters in turn yields insights into important phenomena for accident progression and off-site consequences. This uncertainty analysis confirmed the known importance of some parameters, such as failure rate of the Safety Relief Valve in accident progression modeling and the dry deposition velocity in off-site consequence modeling. The analysis also revealed some new insights, such as dependent effect of cesium chemical form for different accident progressions. (auth)« less

Management system of health and safety work (SMK3) with job safety analysis (JSA) in PT. Nira Murni construction

NASA Astrophysics Data System (ADS)

Melliana, Armen, Yusrizal, Akmal, Syarifah

2017-11-01

PT Nira Murni construction is a contractor of PT Chevron Pacific Indonesia which engaged in contractor, fabrication, maintenance construction suppliers, and labor services. The high of accident rate in this company is caused the lack of awareness of workplace safety. Therefore, it requires an effort to reduce the accident rate on the company so that the financial losses can be minimized. In this study, Safe T-Score method is used to analyze the accident rate by measuring the level of frequency. Analysis is continued using risk management methods which identify hazards, risk measurement and risk management. The last analysis uses Job safety analysis (JSA) which will identify the effect of accidents. From the result of this study can be concluded that Job Safety Analysis (JSA) methods has not been implemented properly. Therefore, JSA method needs to follow-up in the next study, so that can be well applied as prevention of occupational accidents.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattison, M.B.; Schroeder, J.A.; Russell, K.D.

The Idaho National Engineering Laboratory (INEL) over the past year has created 75 plant-specific Accident Sequence Precursor (ASP) models using the SAPHIRE suite of PRA codes. Along with the new models, the INEL has also developed a new module for SAPHIRE which is tailored specifically to the unique needs of ASP evaluations. These models and software will be the next generation of risk tools for the evaluation of accident precursors by both NRR and AEOD. This paper presents an overview of the models and software. Key characteristics include: (1) classification of the plant models according to plant response with amore » unique set of event trees for each plant class, (2) plant-specific fault trees using supercomponents, (3) generation and retention of all system and sequence cutsets, (4) full flexibility in modifying logic, regenerating cutsets, and requantifying results, and (5) user interface for streamlined evaluation of ASP events.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattison, M.B.; Schroeder, J.A.; Russell, K.D.

The Idaho National Engineering Laboratory (INEL) over the past year has created 75 plant-specific Accident Sequence Precursor (ASP) models using the SAPHIRE suite of PRA codes. Along with the new models, the INEL has also developed a new module for SAPHIRE which is tailored specifically to the unique needs of conditional core damage probability (CCDP) evaluations. These models and software will be the next generation of risk tools for the evaluation of accident precursors by both NRR and AEOD. This paper presents an overview of the models and software. Key characteristics include: (1) classification of the plant models according tomore » plant response with a unique set of event trees for each plant class, (2) plant-specific fault trees using supercomponents, (3) generation and retention of all system and sequence cutsets, (4) full flexibility in modifying logic, regenerating cutsets, and requantifying results, and (5) user interface for streamlined evaluation of ASP events.« less

A summary of unmanned aircraft accident/incident data : human factors implications

DOT National Transportation Integrated Search

2004-12-01

A review and analysis of unmanned aircraft (UA) accident data was conducted to identify important human factors issues related to their use. UA accident data were collected from the U.S. Army, Navy, and Air Force. Classification of the accident data ...

Glider accidents: an analysis of 143 cases, 2001-2005.

PubMed

van Doorn, Robert R A; de Voogt, Alexander J

2007-01-01

The majority of aviation crashes and casualties take place in general and sport aviation. Although gliding has gained popularity in recent decades, we could find no systematic analysis of glider accidents. This study determined factors associated with both non-fatal and fatal glider accidents to document their position within sport and general aviation accidents, and to suggest preventive measures and improvements. We performed a retrospective review of glider accidents for the period 2001-2005 in the database maintained by the U.S. National Transportation Safety Board (NTSB). A total of 117 non-fatal and 26 fatal glider accidents were reported for the 5-yr period. Adverse weather was the cause in 20% of all non-fatal accidents, 60% of which occurred in the cruise phase. Logistic regression revealed that fatal accidents were predicted by pilot error, flight phase, and home-built aircraft. Factors contributing to glider crashes are specific to this type of sport aviation. Owners of home-built gliders should pay particular attention to the aircraft's specifications and design limits.

Methods for nuclear air-cleaning-system accident-consequence assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrae, R.W.; Bolstad, J.W.; Gregory, W.S.

1982-01-01

This paper describes a multilaboratory research program that is directed toward addressing many questions that analysts face when performing air cleaning accident consequence assessments. The program involves developing analytical tools and supportive experimental data that will be useful in making more realistic assessments of accident source terms within and up to the atmospheric boundaries of nuclear fuel cycle facilities. The types of accidents considered in this study includes fires, explosions, spills, tornadoes, criticalities, and equipment failures. The main focus of the program is developing an accident analysis handbook (AAH). We will describe the contents of the AAH, which include descriptionsmore » of selected nuclear fuel cycle facilities, process unit operations, source-term development, and accident consequence analyses. Three computer codes designed to predict gas and material propagation through facility air cleaning systems are described. These computer codes address accidents involving fires (FIRAC), explosions (EXPAC), and tornadoes (TORAC). The handbook relies on many illustrative examples to show the analyst how to approach accident consequence assessments. We will use the FIRAC code and a hypothetical fire scenario to illustrate the accident analysis capability.« less

To Err is Human Case Reports of Two Military Aircraft Accidents

PubMed Central

Dikshit, Mohan B

2010-01-01

It has been postulated that pilot error or in-flight incapacitation may be the main contributory factors to 70–80% of aircraft accidents. Two fatal aircraft accidents are presented in which either of the above possibilities may have played a role. The first case report describes an erroneous decision by a fighter pilot to use a seat position adjustment of the ejection seat leading to fatal injuries when he had to eject from his aircraft. Injuries to the body of the pilot, and observations on the state of his flying clothing and the ejection seat were used to postulate the mechanism of fatal injury and establish the cause of the accident. The second case report describes the sequence of events which culminated in the incapacitation of a fighter pilot while executing a routine manouevre. This resulted in a fatal air crash. Possible contributions of environmental factors which may have resulted in failure of his physiological mechanisms are discussed. PMID:21509093

The Human Factors of an Early Space Accident: Flight 3-65 of the X-15

NASA Technical Reports Server (NTRS)

Barshi, Immanuel; Statler, Irving C.; Orr, Jeb S.

2015-01-01

The X-15 was a critical research vehicle in the early days of space flight. On November 15, 1967, the X-15-3 suffered an in-flight breakup. This 191st flight of the X-15 and the 65th flight of this third configuration was the only fatal accident of the X-15 program. This paper presents an analysis, from a human factors perspective, of the events that led up to the accident. The analysis is based on the information contained in the report of the Air Force-NASA Accident Investigation Board (AIB) dated January, 1968. The AIBs analysis addressed, primarily, the events that occurred subsequent to the pilots taking direct control of the reaction control system. The analysis described here suggests that all of the events that caused the accident occurred well before the moment when the pilot switched to direct control. Consequently, the analyses and conclusions regarding the causal factors of, and the contributing factors to, the loss of Flight 3-65 presented here differ from those of the AIB based on the same evidence. Although the accident occurred in 1967, the results of the presented analysis are still relevant today. We present our analysis and discuss its implications for the safety of space operations.

The Human Factors of an Early Space Accident: Flight 3-65 of the X-15

NASA Technical Reports Server (NTRS)

Barshi, Immanuel; Statler, Irving C.; Orr, Jeb S.

2016-01-01

The X-15 was a critical research vehicle in the early days of space flight. On November 15, 1967, the X-15-3 suffered an in-flight breakup. This 191st flight of the X-15 and the 65th flight of this third configuration was the only fatal accident of the X-15 program. This paper presents an analysis, from a human factors perspective, of the events that led up to the accident. The analysis is based on the information contained in the report of the Air Force-NASA Accident Investigation Board (AIB) dated January, 1968. The AIBs analysis addressed, primarily, the events that occurred subsequent to the pilot's taking direct control of the reaction control system. The analysis described here suggests that, rather than events following the pilot's switch to direct control, it was the events preceding the switch that led to the accident. Consequently, the analyses and conclusions regarding the causal factors of, and the contributing factors to, the loss of Flight 3-65 presented here differ from those of the AIB based on the same evidence. Although the accident occurred in 1967, the results of the presented analysis are still relevant today. We present our analysis and discuss its implications for the safety of space operations.

A case study analysis to examine motorcycle crashes in Bogota, Colombia.

PubMed

Jimenez, Adriana; Bocarejo, Juan Pablo; Zarama, Roberto; Yerpez, Joël

2015-02-01

Contributory factors to motorcycle crashes vary among populations depending on several aspects such as the users' profiles, the composition and density of traffic, and the infrastructure features. A better understanding of local motorcycle crashes can be reached in those places where a comprehensive analysis is performed. This paper presents the results obtained from a case study analysis of 400 police records of accidents involving motorcycles in Bogota. To achieve a deeper level of understanding of how these accidents occur, we propose a systemic approach that uses available crash data. The methodology is inspired by accident prototypical scenarios, a tool for analysis developed in France. When grouping cases we identified three categories: solo motorcycle accidents, motorcyclist and pedestrian accidents, and accidents involving a motorcycle and another vehicle. Within these categories we undertook in-depth analyses of 32 groups of accidents obtaining valuable information to better comprehend motorcyclists' road crashes in a local context. Recurrent contributory factors in the groups of accidents include: inexperienced motorcyclists, wide urban roads that incite speeding and risky overtaking maneuvers, flowing urban roads that encourage high speed and increased interaction between vehicles, and lack of infrastructure maintenance. The results obtained are a valuable asset to define measures that will be conveniently adapted to the group of accident on which we want to act. The methodology exposed in this paper is applicable to the study of road crashes that involve all types of actors, not only the motorcyclists, and in contexts different than those presented in Bogota. Copyright © 2014 National Safety Council and Elsevier Ltd. All rights reserved.

Analysis of construction accidents in Spain, 2003-2008.

PubMed

López Arquillos, Antonio; Rubio Romero, Juan Carlos; Gibb, Alistair

2012-12-01

The research objective for this paper is to obtain a new extended and updated insight to the likely causes of construction accidents in Spain, in order to identify suitable mitigating actions. The paper analyzes all construction sector accidents in Spain between 2003 and 2008. Ten variables were chosen and the influence of each variable is evaluated with respect to the severity of the accident. The descriptive analysis is based on a total of 1,163,178 accidents. Results showed that the severity of accidents was related to variables including age, CNAE (National Classification of Economic Activities) code, size of company, length of service, location of accident, day of the week, days of absence, deviation, injury, and climatic zones. According to data analyzed, a large company is not always necessarily safer than a small company in the aspect of fatal accidents, experienced workers do not have the best accident fatality rates, and accidents occurring away from the usual workplace had more severe consequences. Results obtained in this paper can be used by companies in their occupational safety strategies, and in their safety training programs. Copyright © 2012 National Safety Council and Elsevier Ltd. All rights reserved.

Developmental assessment of the Fort St. Vrain version of the Composite HTGR Analysis Program (CHAP-2)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stroh, K.R.

1980-01-01

The Composite HTGR Analysis Program (CHAP) consists of a model-independent systems analysis mainframe named LASAN and model-dependent linked code modules, each representing a component, subsystem, or phenomenon of an HTGR plant. The Fort St. Vrain (FSV) version (CHAP-2) includes 21 coded modules that model the neutron kinetics and thermal response of the core; the thermal-hydraulics of the reactor primary coolant system, secondary steam supply system, and balance-of-plant; the actions of the control system and plant protection system; the response of the reactor building; and the relative hazard resulting from fuel particle failure. FSV steady-state and transient plant data are beingmore » used to partially verify the component modeling and dynamic smulation techniques used to predict plant response to postulated accident sequences.« less

Introduction of Bayesian network in risk analysis of maritime accidents in Bangladesh

NASA Astrophysics Data System (ADS)

Rahman, Sohanur

2017-12-01

Due to the unique geographic location, complex navigation environment and intense vessel traffic, a considerable number of maritime accidents occurred in Bangladesh which caused serious loss of life, property and environmental contamination. Based on the historical data of maritime accidents from 1981 to 2015, which has been collected from Department of Shipping (DOS) and Bangladesh Inland Water Transport Authority (BIWTA), this paper conducted a risk analysis of maritime accidents by applying Bayesian network. In order to conduct this study, a Bayesian network model has been developed to find out the relation among parameters and the probability of them which affect accidents based on the accident investigation report of Bangladesh. Furthermore, number of accidents in different categories has also been investigated in this paper. Finally, some viable recommendations have been proposed in order to ensure greater safety of inland vessels in Bangladesh.

Analysis of Convair 990 rejected-takeoff accident with emphasis on decision making, training and procedures

NASA Technical Reports Server (NTRS)

Batthauer, Byron E.

1987-01-01

This paper analyzes a NASA Convair 990 (CV-990) accident with emphasis on rejected-takeoff (RTO) decision making, training, procedures, and accident statistics. The NASA Aircraft Accident Investigation Board was somewhat perplexed that an aircraft could be destroyed as a result of blown tires during the takeoff roll. To provide a better understanding of tire failure RTO's, The Board obtained accident reports, Federal Aviation Administration (FAA) studies, and other pertinent information related to the elements of this accident. This material enhanced the analysis process and convinced the Accident Board that high-speed RTO's in transport aircraft should be given more emphasis during pilot training. Pilots should be made aware of various RTO situations and statistics with emphasis on failed-tire RTO's. This background information could enhance the split-second decision-making process that is required prior to initiating an RTO.

Work-related accidents among the Iranian population: a time series analysis, 2000–2011

PubMed Central

Karimlou, Masoud; Imani, Mehdi; Hosseini, Agha-Fatemeh; Dehnad, Afsaneh; Vahabi, Nasim; Bakhtiyari, Mahmood

2015-01-01

Background Work-related accidents result in human suffering and economic losses and are considered as a major health problem worldwide, especially in the economically developing world. Objectives To introduce seasonal autoregressive moving average (ARIMA) models for time series analysis of work-related accident data for workers insured by the Iranian Social Security Organization (ISSO) between 2000 and 2011. Methods In this retrospective study, all insured people experiencing at least one work-related accident during a 10-year period were included in the analyses. We used Box–Jenkins modeling to develop a time series model of the total number of accidents. Results There was an average of 1476 accidents per month (1476·05±458·77, mean±SD). The final ARIMA (p,d,q) (P,D,Q)s model for fitting to data was: ARIMA(1,1,1)×(0,1,1)12 consisting of the first ordering of the autoregressive, moving average and seasonal moving average parameters with 20·942 mean absolute percentage error (MAPE). Conclusions The final model showed that time series analysis of ARIMA models was useful for forecasting the number of work-related accidents in Iran. In addition, the forecasted number of work-related accidents for 2011 explained the stability of occurrence of these accidents in recent years, indicating a need for preventive occupational health and safety policies such as safety inspection. PMID:26119774

Work-related accidents among the Iranian population: a time series analysis, 2000-2011.

PubMed

Karimlou, Masoud; Salehi, Masoud; Imani, Mehdi; Hosseini, Agha-Fatemeh; Dehnad, Afsaneh; Vahabi, Nasim; Bakhtiyari, Mahmood

2015-01-01

Work-related accidents result in human suffering and economic losses and are considered as a major health problem worldwide, especially in the economically developing world. To introduce seasonal autoregressive moving average (ARIMA) models for time series analysis of work-related accident data for workers insured by the Iranian Social Security Organization (ISSO) between 2000 and 2011. In this retrospective study, all insured people experiencing at least one work-related accident during a 10-year period were included in the analyses. We used Box-Jenkins modeling to develop a time series model of the total number of accidents. There was an average of 1476 accidents per month (1476·05±458·77, mean±SD). The final ARIMA (p,d,q) (P,D,Q)s model for fitting to data was: ARIMA(1,1,1)×(0,1,1)12 consisting of the first ordering of the autoregressive, moving average and seasonal moving average parameters with 20·942 mean absolute percentage error (MAPE). The final model showed that time series analysis of ARIMA models was useful for forecasting the number of work-related accidents in Iran. In addition, the forecasted number of work-related accidents for 2011 explained the stability of occurrence of these accidents in recent years, indicating a need for preventive occupational health and safety policies such as safety inspection.

A comprehensive probabilistic analysis model of oil pipelines network based on Bayesian network

NASA Astrophysics Data System (ADS)

Zhang, C.; Qin, T. X.; Jiang, B.; Huang, C.

2018-02-01

Oil pipelines network is one of the most important facilities of energy transportation. But oil pipelines network accident may result in serious disasters. Some analysis models for these accidents have been established mainly based on three methods, including event-tree, accident simulation and Bayesian network. Among these methods, Bayesian network is suitable for probabilistic analysis. But not all the important influencing factors are considered and the deployment rule of the factors has not been established. This paper proposed a probabilistic analysis model of oil pipelines network based on Bayesian network. Most of the important influencing factors, including the key environment condition and emergency response are considered in this model. Moreover, the paper also introduces a deployment rule for these factors. The model can be used in probabilistic analysis and sensitive analysis of oil pipelines network accident.

10 CFR 76.85 - Assessment of accidents.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

10 CFR 76.85 - Assessment of accidents.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

10 CFR 76.85 - Assessment of accidents.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

10 CFR 76.85 - Assessment of accidents.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

10 CFR 76.85 - Assessment of accidents.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

Analysis of occupational accidents with biological material among professionals in pre-hospital services.

PubMed

de Oliveira, Adriana Cristina; Paiva, Maria Henriqueta Rocha Siqueira

2013-02-01

To estimate the prevalence of accidents due to biological material exposure, the characteristics and post-accident conduct among professionals of pre-hospital services of the four municipalities of Minas Gerais, Brazil. A cross-sectional study, using a structured questionnaire that was developed to enable the calculation of prevalence, descriptive analysis and analytical analysis using logistic regression. The study included 228 professionals; the prevalence of accidents due to biological material exposure was 29.4%, with 49.2% percutaneous, 10.4% mucousal, 6.0% non-intact skin, and 34.4% intact skin. Among the professionals injured, those that stood out were nursing technicians (41.9%) and drivers (28.3%). Notification of the occurrence of the accident occurred in 29.8% of the cases. Percutaneous exposure was associated with time of work in the organization (OR=2.51, 95% CI: 1.18 to 5.35, p<0.017). Notification about accidents with biological material should be encouraged, along with professional evaluation/monitoring.

Single pilot IFR accident data analysis

NASA Technical Reports Server (NTRS)

Harris, D. F.; Morrisete, J. A.

1982-01-01

The aircraft accident data recorded and maintained by the National Transportation Safety Board for 1964 to 1979 were analyzed to determine what problems exist in the general aviation single pilot instrument flight rules environment. A previous study conducted in 1978 for the years 1964 to 1975 provided a basis for comparison. The purpose was to determine what changes, if any, have occurred in trends and cause-effect relationships reported in the earlier study. The increasing numbers have been tied to measures of activity to produce accident rates which in turn were analyzed in terms of change. Where anomalies or unusually high accident rates were encountered, further analysis was conducted to isolate pertinent patterns of cause factors and/or experience levels of involved pilots. The bulk of the effort addresses accidents in the landing phase of operations. A detailed analysis was performed on controlled/uncontrolled collisions and their unique attributes delineated. Estimates of day vs. night general aviation activity and accident rates were obtained.

Final report on the analyses of traffic accidents : Fast-Trac--phase 3, deliverable. Semi-annual reports on total accidents : trends, types and analysis of before and after studies

DOT National Transportation Integrated Search

1996-12-01

This report contains the results of an analysis of : traffic accidents in the City of Troy, Michigan, where : the Sydney Coordinated Adaptive Traffic System : (SCATS) was deployed as part of a federal demonstration : program. The analyses includes a ...

Data Analysis Approaches for the Risk-Informed Safety Margins Characterization Toolkit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mandelli, Diego; Alfonsi, Andrea; Maljovec, Daniel P.

2016-09-01

In the past decades, several numerical simulation codes have been employed to simulate accident dynamics (e.g., RELAP5-3D, RELAP-7, MELCOR, MAAP). In order to evaluate the impact of uncertainties into accident dynamics, several stochastic methodologies have been coupled with these codes. These stochastic methods range from classical Monte-Carlo and Latin Hypercube sampling to stochastic polynomial methods. Similar approaches have been introduced into the risk and safety community where stochastic methods (such as RAVEN, ADAPT, MCDET, ADS) have been coupled with safety analysis codes in order to evaluate the safety impact of timing and sequencing of events. These approaches are usually calledmore » Dynamic PRA or simulation-based PRA methods. These uncertainties and safety methods usually generate a large number of simulation runs (database storage may be on the order of gigabytes or higher). The scope of this paper is to present a broad overview of methods and algorithms that can be used to analyze and extract information from large data sets containing time dependent data. In this context, “extracting information” means constructing input-output correlations, finding commonalities, and identifying outliers. Some of the algorithms presented here have been developed or are under development within the RAVEN statistical framework.« less

Causative factors and countermeasures for rural and suburban pedestrian accidents : accident data collection and analysis

DOT National Transportation Integrated Search

1977-03-01

The objectives of the study were to collect and analyze data on rural pedestrian accidents and to identify potential countermeasures. Data on a stratified random sample of over 1,500 rural and suburban accidents from six states was collected during i...

Causative factors and countermeasures for rural and suburban pedestrian accidents : accident data collection and analysis--appendices

DOT National Transportation Integrated Search

1977-06-01

The objectives of the study were to collect and analyze data on rural pedestrian accidents and to identify potential countermeasures. Data on a stratified random sample of over 1,500 rural and suburban accidents from six states was collected during i...

Profile of an Accident Flying Squad

PubMed Central

Little, Keith

1972-01-01

An analysis of 184 accident flying squad calls and of 280 patients injured in road accidents and treated by a flying squad based on an accident department inclusive from 1967 to 1971 has shown that such a service can provide an efficient system without disrupting the routine work of the hospital. PMID:5076258

Profile of an accident flying squad.

PubMed

Little, K

1972-09-30

An analysis of 184 accident flying squad calls and of 280 patients injured in road accidents and treated by a flying squad based on an accident department inclusive from 1967 to 1971 has shown that such a service can provide an efficient system without disrupting the routine work of the hospital.

Corporate cost of occupational accidents: an activity-based analysis.

PubMed

Rikhardsson, Pall M; Impgaard, Martin

2004-03-01

The systematic accident cost analysis (SACA) project was carried out during 2001 by The Aarhus School of Business and PricewaterhouseCoopers Denmark with financial support from The Danish National Working Environment Authority. Its focused on developing and testing a method for evaluating occupational costs of companies for use by occupational health and safety professionals. The method was tested in nine Danish companies within three different industry sectors and the costs of 27 selected occupational accidents in these companies were calculated. One of the main conclusions is that the SACA method could be used in all of the companies without revisions. The evaluation of accident cost showed that 2/3 of the costs of occupational accidents are visible in the Danish corporate accounting systems reviewed while 1/3 is hidden from management view. The highest cost of occupational accidents for a company with 3.600 employees was estimated to approximately US$ 682.000. The paper includes an introduction regarding accident cost analysis in companies, a presentation of the SACA project methodology and the SACA method itself, a short overview of some of the results of the SACA project and a conclusion. Further information about the project is available at http://www.asb.dk/saca.

A quarter of a century of the DBQ: some supplementary notes on its validity with regard to accidents.

PubMed

de Winter, Joost C F; Dodou, Dimitra; Stanton, Neville A

2015-01-01

This article synthesises the latest information on the relationship between the Driver Behaviour Questionnaire (DBQ) and accidents. We show by means of computer simulation that correlations with accidents are necessarily small because accidents are rare events. An updated meta-analysis on the zero-order correlations between the DBQ and self-reported accidents yielded an overall r of .13 (fixed-effect and random-effects models) for violations (57,480 participants; 67 samples) and .09 (fixed-effect and random-effects models) for errors (66,028 participants; 56 samples). An analysis of a previously published DBQ dataset (975 participants) showed that by aggregating across four measurement occasions, the correlation coefficient with self-reported accidents increased from .14 to .24 for violations and from .11 to .19 for errors. Our meta-analysis also showed that DBQ violations (r = .24; 6353 participants; 20 samples) but not DBQ errors (r = - .08; 1086 participants; 16 samples) correlated with recorded vehicle speed. Practitioner Summary: The DBQ is probably the most widely used self-report questionnaire in driver behaviour research. This study shows that DBQ violations and errors correlate moderately with self-reported traffic accidents.

Routes to failure: analysis of 41 civil aviation accidents from the Republic of China using the human factors analysis and classification system.

PubMed

Li, Wen-Chin; Harris, Don; Yu, Chung-San

2008-03-01

The human factors analysis and classification system (HFACS) is based upon Reason's organizational model of human error. HFACS was developed as an analytical framework for the investigation of the role of human error in aviation accidents, however, there is little empirical work formally describing the relationship between the components in the model. This research analyses 41 civil aviation accidents occurring to aircraft registered in the Republic of China (ROC) between 1999 and 2006 using the HFACS framework. The results show statistically significant relationships between errors at the operational level and organizational inadequacies at both the immediately adjacent level (preconditions for unsafe acts) and higher levels in the organization (unsafe supervision and organizational influences). The pattern of the 'routes to failure' observed in the data from this analysis of civil aircraft accidents show great similarities to that observed in the analysis of military accidents. This research lends further support to Reason's model that suggests that active failures are promoted by latent conditions in the organization. Statistical relationships linking fallible decisions in upper management levels were found to directly affect supervisory practices, thereby creating the psychological preconditions for unsafe acts and hence indirectly impairing the performance of pilots, ultimately leading to accidents.

Statistical Analysis And Treatment Of Accident Black Spots: A Case Study Of Nandyal Mandal

NASA Astrophysics Data System (ADS)

Sudharshan Reddy, B.; Vishnu Vardhan Reddy, L.; Sreenivasa Reddy, G., Dr

2017-08-01

Background: Increased, economic activity raised the consumption levels of the people across the country. This created scope for increase in travel and transportation. The increase in the vehicles since last 10 years has put lot of pressure on the existing roads and ultimately resulting in road accidents. Nandyal Mandal is located in the Kurnool district of Andhra Pradesh and well developed in both agricultural and industrial sectors after Kurnool. 567 accidents occurred in the last seven years at 143 locations shows the severity of the accidents in the Nandyal Mandal. There is a need to carry out some work in the Nandyal Mandal to improve the accidents black spots for reducing the accidents. Methods: Last seven years (2010-2016) of accident data collected from Police Stations. Weighted Severity Index (WSI), a scientific method is used for identifying the accident black spots. Statistical analysis has carried out for the collected data using Chi-Square Test to determine the independence of accidents with other attributes. Chi-Square Goodness of fit test conducted for test whether the accidents are occurring by chance or following any pattern. Results: WSI values are determined for the 143 locations. The Locations with high WSI are treated as accident black spots. Five black spots are taken for field study. After field observations and interaction with the public, some improvements are suggested for improving the accident black spots. There is no relationship between the severity of accidents and the other attributes like month, season, day, hours in day and the age group except type of vehicle. Road accidents are distributed throughout the Year, Month and Season. Road accidents are not distributed throughout the day.

Historical analysis of US pipeline accidents triggered by natural hazards

NASA Astrophysics Data System (ADS)

Girgin, Serkan; Krausmann, Elisabeth

2015-04-01

Natural hazards, such as earthquakes, floods, landslides, or lightning, can initiate accidents in oil and gas pipelines with potentially major consequences on the population or the environment due to toxic releases, fires and explosions. Accidents of this type are also referred to as Natech events. Many major accidents highlight the risk associated with natural-hazard impact on pipelines transporting dangerous substances. For instance, in the USA in 1994, flooding of the San Jacinto River caused the rupture of 8 and the undermining of 29 pipelines by the floodwaters. About 5.5 million litres of petroleum and related products were spilled into the river and ignited. As a results, 547 people were injured and significant environmental damage occurred. Post-incident analysis is a valuable tool for better understanding the causes, dynamics and impacts of pipeline Natech accidents in support of future accident prevention and mitigation. Therefore, data on onshore hazardous-liquid pipeline accidents collected by the US Pipeline and Hazardous Materials Safety Administration (PHMSA) was analysed. For this purpose, a database-driven incident data analysis system was developed to aid the rapid review and categorization of PHMSA incident reports. Using an automated data-mining process followed by a peer review of the incident records and supported by natural hazard databases and external information sources, the pipeline Natechs were identified. As a by-product of the data-collection process, the database now includes over 800,000 incidents from all causes in industrial and transportation activities, which are automatically classified in the same way as the PHMSA record. This presentation describes the data collection and reviewing steps conducted during the study, provides information on the developed database and data analysis tools, and reports the findings of a statistical analysis of the identified hazardous liquid pipeline incidents in terms of accident dynamics and consequences.

A methodology for accident analysis of fusion breeder blankets and its application to helium-cooled lead–lithium blanket

DOE PAGES

Panayotov, Dobromir; Poitevin, Yves; Grief, Andrew; ...

2016-09-23

'Fusion for Energy' (F4E) is designing, developing, and implementing the European Helium-Cooled Lead-Lithium (HCLL) and Helium-Cooled Pebble-Bed (HCPB) Test Blanket Systems (TBSs) for ITER (Nuclear Facility INB-174). Safety demonstration is an essential element for the integration of these TBSs into ITER and accident analysis is one of its critical components. A systematic approach to accident analysis has been developed under the F4E contract on TBS safety analyses. F4E technical requirements, together with Amec Foster Wheeler and INL efforts, have resulted in a comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials,more » and phenomena while remaining consistent with the approach already applied to ITER accident analyses. Furthermore, the methodology phases are illustrated in the paper by its application to the EU HCLL TBS using both MELCOR and RELAP5 codes.« less

Accident Journalism and Traffic Safety Education: A Three-Phase Investigation of Accident Reporting in the Canadian Daily Press.

ERIC Educational Resources Information Center

Wilde, Gerald J. S.; Ackersviller, Melody J.

A study examined the potential for development of a traffic accident-reporting form in the Canadian daily press that strengthens concern for road safety in the general population and enhances knowledge, attitudes, and behavior leading to greater safety. The investigation was conducted on three levels: a content analysis, a readership analysis, and…

Analysis of Sertraline in Postmortem Fluids and Tissues in 11 Aviation Accident Victims

DTIC Science & Technology

2012-11-01

likely undergoes significant postmortem redistribution. 17. Key Words 18. Distribution Statement Forensic Toxicology , Sertraline, Norsertraline... Toxicology .. Forensic Sci Int,.142:.75-100.(2004) . 29 .. Skopp,.G ..Postmortem.Toxicology .. Forensic Sci Med Pathol,.6:.314-25.(2010) . ... toxicological . analysis. on. specimens.from.….aircraft.accident.fatalities”.and.“in- vestigate.….general.aviation.and.air.carrier.accidents. and. search

[Model of Analysis and Prevention of Accidents - MAPA: tool for operational health surveillance].

PubMed

de Almeida, Ildeberto Muniz; Vilela, Rodolfo Andrade de Gouveia; da Silva, Alessandro José Nunes; Beltran, Sandra Lorena

2014-12-01

The analysis of work-related accidents is important for accident surveillance and prevention. Current methods of analysis seek to overcome reductionist views that see these occurrences as simple events explained by operator error. The objective of this paper is to analyze the Model of Analysis and Prevention of Accidents (MAPA) and its use in monitoring interventions, duly highlighting aspects experienced in the use of the tool. The descriptive analytical method was used, introducing the steps of the model. To illustrate contributions and or difficulties, cases where the tool was used in the context of service were selected. MAPA integrates theoretical approaches that have already been tried in studies of accidents by providing useful conceptual support from the data collection stage until conclusion and intervention stages. Besides revealing weaknesses of the traditional approach, it helps identify organizational determinants, such as management failings, system design and safety management involved in the accident. The main challenges lie in the grasp of concepts by users, in exploring organizational aspects upstream in the chain of decisions or at higher levels of the hierarchy, as well as the intervention to change the determinants of these events.

Rotorcraft Drivetrain Life Safety and Reliability (Cycle de Vie, Securite et Fiabilite des Chaines Dynamiques des Avions a Voilure Tournante)

DTIC Science & Technology

1990-06-01

design and component technologies are reviewed against a background of accident data analysis , resulting in grounds for confidence in higher safety levels...constructors or operators taking voluntary actions based on accident investigations and their own data . Analysis of the CAA Summaty data (Appendix 3...of engines. In the accident data analysis in Appendix 3, insufficient data was available to determine whether rotor configuration or associated

Human factors analysis and classification system applied to civil aircraft accidents in India.

PubMed

Gaur, Deepak

2005-05-01

The Human Factors Analysis and Classification System (HFACS) has gained wide acceptance as a tool to classify human factors in aircraft accidents and incidents. This study on application of HFACS to civil aircraft accident reports at Directorate General Civil of Aviation (DGCA), India, was conducted to ascertain the practicability of applying HFACS to existing investigation reports and to analyze the trends of human factor causes of civil aircraft accidents. Accident investigation reports held at DGCA, New Delhi, for the period 1990--99 were scrutinized. In all, 83 accidents occurred during this period, of which 48 accident reports were evaluated in this study. One or more human factors contributed to 37 of the 48 (77.1%) accidents. The commonest unsafe act was 'skill based errors' followed by 'decision errors.' Violations of laid down rules were contributory in 16 cases (33.3%). 'Preconditions for unsafe acts' were seen in 23 of the 48 cases (47.9%). A fairly large number (52.1%) had 'organizational influences' contributing to the accident. These results are in consonance with larger studies of accidents in the U.S. Navy and general aviation. Such a high percentage of 'organizational influences' has not been reported in other studies. This is a healthy sign for Indian civil aviation, provided effective remedial action for the same is undertaken.

Analysis of Occupational Accidents in Underground and Surface Mining in Spain Using Data-Mining Techniques

PubMed Central

Sanmiquel, Lluís; Bascompta, Marc; Rossell, Josep M.; Anticoi, Hernán Francisco; Guash, Eduard

2018-01-01

An analysis of occupational accidents in the mining sector was conducted using the data from the Spanish Ministry of Employment and Social Safety between 2005 and 2015, and data-mining techniques were applied. Data was processed with the software Weka. Two scenarios were chosen from the accidents database: surface and underground mining. The most important variables involved in occupational accidents and their association rules were determined. These rules are composed of several predictor variables that cause accidents, defining its characteristics and context. This study exposes the 20 most important association rules in the sector—either surface or underground mining—based on the statistical confidence levels of each rule as obtained by Weka. The outcomes display the most typical immediate causes, along with the percentage of accidents with a basis in each association rule. The most important immediate cause is body movement with physical effort or overexertion, and the type of accident is physical effort or overexertion. On the other hand, the second most important immediate cause and type of accident are different between the two scenarios. Data-mining techniques were chosen as a useful tool to find out the root cause of the accidents. PMID:29518921

Analysis of Occupational Accidents in Underground and Surface Mining in Spain Using Data-Mining Techniques.

PubMed

Sanmiquel, Lluís; Bascompta, Marc; Rossell, Josep M; Anticoi, Hernán Francisco; Guash, Eduard

2018-03-07

An analysis of occupational accidents in the mining sector was conducted using the data from the Spanish Ministry of Employment and Social Safety between 2005 and 2015, and data-mining techniques were applied. Data was processed with the software Weka. Two scenarios were chosen from the accidents database: surface and underground mining. The most important variables involved in occupational accidents and their association rules were determined. These rules are composed of several predictor variables that cause accidents, defining its characteristics and context. This study exposes the 20 most important association rules in the sector-either surface or underground mining-based on the statistical confidence levels of each rule as obtained by Weka. The outcomes display the most typical immediate causes, along with the percentage of accidents with a basis in each association rule. The most important immediate cause is body movement with physical effort or overexertion, and the type of accident is physical effort or overexertion. On the other hand, the second most important immediate cause and type of accident are different between the two scenarios. Data-mining techniques were chosen as a useful tool to find out the root cause of the accidents.

Road safety analysis on Achmad Yani frontage road Surabaya

NASA Astrophysics Data System (ADS)

Machsus; Prayogo, I.; Chomaedhi; Hayati, D. W.; Utanaka, A.

2017-11-01

This research discusses road safety analysis on the operation of frontage road on the west side of Achmad Yani Road Surabaya. This research began by conducting survey on secondary data of traffic accidents. In addition, primary data survey was conducted to obtain traffic data, geometric road data, and other supporting data at the study site along the west side frontage of Ahmad Yani Road Surabaya. Devices used in this research include camera, handy cam, speed gun, counters of vehicles, rolling meter, computer and others. In outline, the stages to conduct this research are divided into 4 stages, namely 1.the preparation stage, 2.data collection and processing, 3. analysis and discussion, and 4. conclusion. The results of this study showed that the accident characteristics of the frontage road are (i) 3 accidents occured per month, (ii) motorcycles was accounted for the largest proportion of accidents which amounted to 74.6 percent, (iii) there were 3 accident victims per month, and (iv) material losses per month worths 1.2 million. The accident rate in 2016 was 0.04 crashes per one million vehicle travels per kilometer, while during 2 months in 2017 it was 0.15 accidents per one million vehicle travels per kilometer. Black spot area of accident is located on Sta 2 + 800 to 2 + 900 which is in front of Graha Pena building and DBL Arena. The high rate of accidents is influenced by the speed of the vehicle which 85 percentile exceeds the speed limit of 40km per hour.

Risk analysis of emergent water pollution accidents based on a Bayesian Network.

PubMed

Tang, Caihong; Yi, Yujun; Yang, Zhifeng; Sun, Jie

2016-01-01

To guarantee the security of water quality in water transfer channels, especially in open channels, analysis of potential emergent pollution sources in the water transfer process is critical. It is also indispensable for forewarnings and protection from emergent pollution accidents. Bridges above open channels with large amounts of truck traffic are the main locations where emergent accidents could occur. A Bayesian Network model, which consists of six root nodes and three middle layer nodes, was developed in this paper, and was employed to identify the possibility of potential pollution risk. Dianbei Bridge is reviewed as a typical bridge on an open channel of the Middle Route of the South to North Water Transfer Project where emergent traffic accidents could occur. Risk of water pollutions caused by leakage of pollutants into water is focused in this study. The risk for potential traffic accidents at the Dianbei Bridge implies a risk for water pollution in the canal. Based on survey data, statistical analysis, and domain specialist knowledge, a Bayesian Network model was established. The human factor of emergent accidents has been considered in this model. Additionally, this model has been employed to describe the probability of accidents and the risk level. The sensitive reasons for pollution accidents have been deduced. The case has also been simulated that sensitive factors are in a state of most likely to lead to accidents. Copyright © 2015 Elsevier Ltd. All rights reserved.

Visualization of Traffic Accidents

NASA Technical Reports Server (NTRS)

Wang, Jie; Shen, Yuzhong; Khattak, Asad

2010-01-01

Traffic accidents have tremendous impact on society. Annually approximately 6.4 million vehicle accidents are reported by police in the US and nearly half of them result in catastrophic injuries. Visualizations of traffic accidents using geographic information systems (GIS) greatly facilitate handling and analysis of traffic accidents in many aspects. Environmental Systems Research Institute (ESRI), Inc. is the world leader in GIS research and development. ArcGIS, a software package developed by ESRI, has the capabilities to display events associated with a road network, such as accident locations, and pavement quality. But when event locations related to a road network are processed, the existing algorithm used by ArcGIS does not utilize all the information related to the routes of the road network and produces erroneous visualization results of event locations. This software bug causes serious problems for applications in which accurate location information is critical for emergency responses, such as traffic accidents. This paper aims to address this problem and proposes an improved method that utilizes all relevant information of traffic accidents, namely, route number, direction, and mile post, and extracts correct event locations for accurate traffic accident visualization and analysis. The proposed method generates a new shape file for traffic accidents and displays them on top of the existing road network in ArcGIS. Visualization of traffic accidents along Hampton Roads Bridge Tunnel is included to demonstrate the effectiveness of the proposed method.

49 CFR Appendix B to Part 219 - Designation of Laboratory for Post-Accident Toxicological Testing

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Designation of Laboratory for Post-Accident.... 219, App. B Appendix B to Part 219—Designation of Laboratory for Post-Accident Toxicological Testing The following laboratory is currently designated to conduct post-accident toxicological analysis under...

LNG risk management

NASA Astrophysics Data System (ADS)

Martino, P.

1980-12-01

A general methodology is presented for conducting an analysis of the various aspects of the hazards associated with the storage and transportation of liquefied natural gas (LNG) which should be considered during the planning stages of a typical LNG ship terminal. The procedure includes the performance of a hazards and system analysis of the proposed site, a probability analysis of accident scenarios and safety impacts, an analysis of the consequences of credible accidents such as tanker accidents, spills and fires, the assessment of risks and the design and evaluation of risk mitigation measures.

An Analysis of U.S. Civil Rotorcraft Accidents by Cost and Injury (1990-1996)

NASA Technical Reports Server (NTRS)

Iseler, Laura; DeMaio, Joe; Rutkowski, Michael (Technical Monitor)

2002-01-01

A study of rotorcraft accidents was conducted to identify safety issues and research areas that might lead to a reduction in rotorcraft accidents and fatalities. The primary source of data was summaries of National Transportation Safety Board (NTSB) accident reports. From 1990 to 1996, the NTSB documented 1396 civil rotorcraft accidents in the United States in which 491 people were killed. The rotorcraft data were compared to airline and general aviation data to determine the relative safety of rotorcraft compared to other segments of the aviation industry. In depth analysis of the rotorcraft data addressed demographics, mission, and operational factors. Rotorcraft were found to have an accident rate about ten times that of commercial airliners and about the same as that of general aviation. The likelihood that an accident would be fatal was about equal for all three classes of operation. The most dramatic division in rotorcraft accidents is between flights flown by private pilots versus professional pilots. Private pilots, flying low cost aircraft in benign environments, have accidents that are due, in large part, to their own errors. Professional pilots, in contrast, are more likely to have accidents that are a result of exacting missions or use of specialized equipment. For both groups judgement error is more likely to lead to a fatal accident than are other types of causes. Several approaches to improving the rotorcraft accident rate are recommended. These mostly address improvement in the training of new pilots and improving the safety awareness of private pilots.

Analysis of FARS data on state highways in Oklahoma.

DOT National Transportation Integrated Search

2012-11-01

Analysis of fatality automobile accident data can be challenging in rural areas where a relatively small number of : such accidents occurs on specific sections of highways. Combining crash data for 1998 to 2011 from the Fatality : Analysis Reporting ...

IVHS Countermeasures for Rear-End Collisions, Task 1; Vol. II: Statistical Analysis

DOT National Transportation Integrated Search

1994-02-25

This report is from the NHTSA sponsored program, "IVHS Countermeasures for Rear-End Collisions". This Volume, Volume II, Statistical Analysis, presents the statistical analysis of rear-end collision accident data that characterizes the accidents with...

Preliminary Investigation of Time Remaining Display on the Computer-based Emergency Operating Procedure

NASA Astrophysics Data System (ADS)

Suryono, T. J.; Gofuku, A.

2018-02-01

One of the important thing in the mitigation of accidents in nuclear power plant accidents is time management. The accidents should be resolved as soon as possible in order to prevent the core melting and the release of radioactive material to the environment. In this case, operators should follow the emergency operating procedure related with the accident, in step by step order and in allowable time. Nowadays, the advanced main control rooms are equipped with computer-based procedures (CBPs) which is make it easier for operators to do their tasks of monitoring and controlling the reactor. However, most of the CBPs do not include the time remaining display feature which informs operators of time available for them to execute procedure steps and warns them if the they reach the time limit. Furthermore, the feature will increase the awareness of operators about their current situation in the procedure. This paper investigates this issue. The simplified of emergency operating procedure (EOP) of steam generator tube rupture (SGTR) accident of PWR plant is applied. In addition, the sequence of actions on each step of the procedure is modelled using multilevel flow modelling (MFM) and influenced propagation rule. The prediction of action time on each step is acquired based on similar case accidents and the Support Vector Regression. The derived time will be processed and then displayed on a CBP user interface.

Side differences in cerebrovascular accidents after cardiac surgery: a statistical analysis of neurologic symptoms and possible implications for anatomic mechanisms of aortic particle embolization.

PubMed

Boivie, Patrik; Edström, Cecilia; Engström, Karl Gunnar

2005-03-01

Aortic manipulation and particle embolization have been identified to cause cerebrovascular accidents in cardiac surgery. Recent data suggest that left-hemispheric cerebrovascular accident (right-sided symptoms) is more common, and this has been interpreted as being caused by aortic cannula stream jets. Our aim was to evaluate symptoms of cerebrovascular accident and side differences from a retrospective statistical analysis. During a 2-year period, 2641 consecutive cardiac surgery cases were analyzed. Patients positive for cerebrovascular accident were extracted from a database designed to monitor clinical symptoms. A protocol was used to confirm symptom data with the correct diagnosis in patient records. Patients were subdivided into 3 groups: control, immediate cerebrovascular accident, and delayed cerebrovascular accident. Among pooled patients, immediate and delayed cerebrovascular accidents were 3.0% and 0.9%, respectively. The expected predisposing factors behind immediate cerebrovascular accidents were significant, although the type of operation affected this search. Aortic quality was a strong predictor ( P < .001). The rate of delayed cerebrovascular accident was unaffected by surgery group. Left-sided symptoms of immediate cerebrovascular accident were approximately twice as frequent ( P = .016) as on the contralateral side. This phenomenon was observed for pooled patients and for isolated coronary bypass procedures (n = 1882; P = .025). Immediate cerebrovascular accident and aortic calcifications are linked. The predominance of left-sided symptoms may suggest that aortic manipulation and anatomic mechanisms in the aortic arch are more likely to cause cerebrovascular accidents than effects from cannula stream jets.

Development of a bespoke human factors taxonomy for gliding accident analysis and its revelations about highly inexperienced UK glider pilots.

PubMed

Jarvis, Steve; Harris, Don

2009-08-01

Low-hours solo glider pilots have a high risk of accidents compared to more experienced pilots. Numerous taxonomies for causal accident analysis have been produced for powered aviation but none of these is suitable for gliding, so a new taxonomy was required. A human factors taxonomy specifically for glider operations was developed and used to analyse all UK gliding accidents from 2002 to 2006 for their overall causes as well as factors specific to low hours pilots. Fifty-nine categories of pilot-related accident causation emerged, which were formed into progressively larger categories until four overall human factors groups were arrived at: 'judgement'; 'handling'; 'strategy'; 'attention'. 'Handling' accounted for a significantly higher proportion of injuries than other categories. Inexperienced pilots had considerably more accidents in all categories except 'strategy'. Approach control (path judgement, airbrake and speed handling) as well as landing flare misjudgement were chiefly responsible for the high accident rate in early solo glider pilots.

What can the drivers' own description from combined sources provide in an analysis of driver distraction and low vigilance in accident situations?

PubMed

Tivesten, Emma; Wiberg, Henrik

2013-03-01

Accident data play an important role in vehicle safety development. Accident data sources are generally limited in terms of how much information is provided on driver states and behaviour prior to an accident. However, the precise limitations vary between databases, due to differences in analysis focus and data collection procedures between organisations. If information about a specific accident can be retrieved from more than one data source it should be possible to combine the available information sets to facilitate data from one source to compensate for limitations in the other(s). To investigate the viability of such compensation, this study identified a set of accidents recorded in two different data sources. The first data source investigated was an accident mail survey and the second data source insurance claims documents consisting predominantly of insurance claims completed by the involved road users. An analysis of survey variables was compared to a case analysis including word data derived from the same survey and filed insurance claims documents. For each accident, the added value of having access to more than one source of information was assessed. To limit the scope of this study, three particular topics were investigated: available information on low vigilance (e.g., being drowsy, ill); secondary task distraction (e.g., talking with passengers, mobile phone use); and distraction related to the driving task (e.g., looking for approaching vehicles). Results suggest that for low vigilance and secondary task distraction, a combination of the mail survey and insurance claims documents provide more reliable and detailed pre-crash information than survey variables alone. However, driving related distraction appears to be more difficult to capture. In order to gain a better understanding of the above issues and how frequently they occur in accidents, the data sources and analysis methods suggested here may be combined with other investigation methods such as in-depth accident investigations and pre-crash data recordings. Copyright © 2012 Elsevier Ltd. All rights reserved.

Coastal flooding as a parameter in multi-criteria analysis for industrial site selection

NASA Astrophysics Data System (ADS)

Christina, C.; Memos, C.; Diakoulaki, D.

2014-12-01

Natural hazards can trigger major industrial accidents, which apart from affecting industrial installations may cause a series of accidents with serious impacts on human health and the environment far beyond the site boundary. Such accidents, also called Na-Tech (natural - technical) accidents, deserve particular attention since they can cause release of hazardous substances possibly resulting in severe environmental pollution, explosions and/or fires. There are different kinds of natural events or, in general terms, of natural causes of industrial accidents, such as landslides, hurricanes, high winds, tsunamis, lightning, cold/hot temperature, floods, heavy rains etc that have caused accidents. The scope of this paper is to examine the coastal flooding as a parameter in causing an industrial accident, such as the nuclear disaster in Fukushima, Japan, and the critical role of this parameter in industrial site selection. Land use planning is a complex procedure that requires multi-criteria decision analysis involving economic, environmental and social parameters. In this context the parameter of a natural hazard occurrence, such as coastal flooding, for industrial site selection should be set by the decision makers. In this paper it is evaluated the influence that has in the outcome of a multi-criteria decision analysis for industrial spatial planning the parameter of an accident risk triggered by coastal flooding. The latter is analyzed in the context of both sea-and-inland induced flooding.

A risk analysis of winter navigation in Finnish sea areas.

PubMed

Valdez Banda, Osiris A; Goerlandt, Floris; Montewka, Jakub; Kujala, Pentti

2015-06-01

Winter navigation is a complex but common operation in north-European sea areas. In Finnish waters, the smooth flow of maritime traffic and safety of vessel navigation during the winter period are managed through the Finnish-Swedish winter navigation system (FSWNS). This article focuses on accident risks in winter navigation operations, beginning with a brief outline of the FSWNS. The study analyses a hazard identification model of winter navigation and reviews accident data extracted from four winter periods. These are adopted as a basis for visualizing the risks in winter navigation operations. The results reveal that experts consider ship independent navigation in ice conditions the most complex navigational operation, which is confirmed by accident data analysis showing that the operation constitutes the type of navigation with the highest number of accidents reported. The severity of the accidents during winter navigation is mainly categorized as less serious. Collision is the most typical accident in ice navigation and general cargo the type of vessel most frequently involved in these accidents. Consolidated ice, ice ridges and ice thickness between 15 and 40cm represent the most common ice conditions in which accidents occur. Thus, the analysis presented in this article establishes the key elements for identifying the operation types which would benefit most from further safety engineering and safety or risk management development. Copyright © 2015 Elsevier Ltd. All rights reserved.

Analysis 320 coal mine accidents using structural equation modeling with unsafe conditions of the rules and regulations as exogenous variables.

PubMed

Zhang, Yingyu; Shao, Wei; Zhang, Mengjia; Li, Hejun; Yin, Shijiu; Xu, Yingjun

2016-07-01

Mining has been historically considered as a naturally high-risk industry worldwide. Deaths caused by coal mine accidents are more than the sum of all other accidents in China. Statistics of 320 coal mine accidents in Shandong province show that all accidents contain indicators of "unsafe conditions of the rules and regulations" with a frequency of 1590, accounting for 74.3% of the total frequency of 2140. "Unsafe behaviors of the operator" is another important contributory factor, which mainly includes "operator error" and "venturing into dangerous places." A systems analysis approach was applied by using structural equation modeling (SEM) to examine the interactions between the contributory factors of coal mine accidents. The analysis of results leads to three conclusions. (i) "Unsafe conditions of the rules and regulations," affect the "unsafe behaviors of the operator," "unsafe conditions of the equipment," and "unsafe conditions of the environment." (ii) The three influencing factors of coal mine accidents (with the frequency of effect relation in descending order) are "lack of safety education and training," "rules and regulations of safety production responsibility," and "rules and regulations of supervision and inspection." (iii) The three influenced factors (with the frequency in descending order) of coal mine accidents are "venturing into dangerous places," "poor workplace environment," and "operator error." Copyright © 2016 Elsevier Ltd. All rights reserved.

A new approach to modeling aviation accidents

NASA Astrophysics Data System (ADS)

Rao, Arjun Harsha

General Aviation (GA) is a catchall term for all aircraft operations in the US that are not categorized as commercial operations or military flights. GA aircraft account for almost 97% of the US civil aviation fleet. Unfortunately, GA flights have a much higher fatal accident rate than commercial operations. Recent estimates by the Federal Aviation Administration (FAA) showed that the GA fatal accident rate has remained relatively unchanged between 2010 and 2015, with 1566 fatal accidents accounting for 2650 fatalities. Several research efforts have been directed towards betters understanding the causes of GA accidents. Many of these efforts use National Transportation Safety Board (NTSB) accident reports and data. Unfortunately, while these studies easily identify the top types of accidents (e.g., inflight loss of control (LOC)), they usually cannot identify why these accidents are happening. Most NTSB narrative reports for GA accidents are very short (many are only one paragraph long), and do not contain much information on the causes (likely because the causes were not fully identified). NTSB investigators also code each accident using an event-based coding system, which should facilitate identification of patterns and trends in causation, given the high number of GA accidents each year. However, this system is susceptible to investigator interpretation and error, meaning that two investigators may code the same accident differently, or omit applicable codes. To facilitate a potentially better understanding of GA accident causation, this research develops a state-based approach to check for logical gaps or omissions in NTSB accident records, and potentially fills-in the omissions. The state-based approach offers more flexibility as it moves away from the conventional event-based representation of accidents, which classifies events in accidents into several categories such as causes, contributing factors, findings, occurrences, and phase of flight. The method views aviation accidents as a set of hazardous states of a system (pilot and aircraft), and triggers that cause the system to move between hazardous states. I used the NTSB's accident coding manual (that contains nearly 4000 different codes) to develop a "dictionary" of hazardous states, triggers, and information codes. Then, I created the "grammar", or a set of rules, that: (1) orders the hazardous states in each accident; and, (2) links the hazardous states using the appropriate triggers. This approach: (1) provides a more correct count of the causes for accidents in the NTSB database; and, (2) checks for gaps or omissions in NTSB accident data, and fills in some of these gaps using logic-based rules. These rules also help identify and count causes for accidents that were not discernable from previous analyses of historical accident data. I apply the model to 6200 helicopter accidents that occurred in the US between 1982 and 2015. First, I identify the states and triggers that are most likely to be associated with fatal and non-fatal accidents. The results suggest that non-fatal accidents, which account for approximately 84% of the accidents, provide valuable opportunities to learn about the causes for accidents. Next, I investigate the causes of inflight loss of control using both a conventional approach and using the state-based approach. The conventional analysis provides little insight into the causal mechanism for LOC. For instance, the top cause of LOC is "aircraft control/directional control not maintained", which does not provide any insight. In contrast, the state-based analysis showed that pilots' tendency to clip objects frequently triggered LOC (16.7% of LOC accidents)--this finding was not directly discernable from conventional analyses. Finally, I investigate the causes for improper autorotations using both a conventional approach and the state-based approach. The conventional approach uses modifiers (e.g., "improper", "misjudged") associated with "24520: Autorotation" to identify improper autorotations in the pre-2008 system. In the psot-2008 system, the NTSB represents autorotation as a phase of flight, which has no modifier--making it impossible to determine if the autorotation was unsuccessful. In contrast, the state-based analysis identified 632 improper autorotation accidents, compared to 174 with a conventional analysis. Results from the state-based analysis show that not maintaining rotor RPM and improper flare were among the top reasons for improper autorotations. The presence of the "not possible" trigger in 11.6% of improper autorotations, suggests that it was impossible to make an autorotative landing. Improper use of collective is the sixth most frequent trigger for improper autorotation. Correct use of collective pitch control is crucial to maintain rotor RPM during an autorotation (considering that engines are generally not operational during autorotations).

Interface requirements for coupling a containment code to a reactor system thermal hydraulic codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baratta, A.J.

1997-07-01

To perform a complete analysis of a reactor transient, not only the primary system response but the containment response must also be accounted for. Such transients and accidents as a loss of coolant accident in both pressurized water and boiling water reactors and inadvertent operation of safety relief valves all challenge the containment and may influence flows because of containment feedback. More recently, the advanced reactor designs put forth by General Electric and Westinghouse in the US and by Framatome and Seimens in Europe rely on the containment to act as the ultimate heat sink. Techniques used by analysts andmore » engineers to analyze the interaction of the containment and the primary system were usually iterative in nature. Codes such as RELAP or RETRAN were used to analyze the primary system response and CONTAIN or CONTEMPT the containment response. The analysis was performed by first running the system code and representing the containment as a fixed pressure boundary condition. The flows were usually from the primary system to the containment initially and generally under choked conditions. Once the mass flows and timing are determined from the system codes, these conditions were input into the containment code. The resulting pressures and temperatures were then calculated and the containment performance analyzed. The disadvantage of this approach becomes evident when one performs an analysis of a rapid depressurization or a long term accident sequence in which feedback from the containment can occur. For example, in a BWR main steam line break transient, the containment heats up and becomes a source of energy for the primary system. Recent advances in programming and computer technology are available to provide an alternative approach. The author and other researchers have developed linkage codes capable of transferring data between codes at each time step allowing discrete codes to be coupled together.« less

Lifestyle and accidents among young drivers.

PubMed

Gregersen, N P; Berg, H Y

1994-06-01

This study covers the lifestyle component of the problems related to young drivers' accident risk. The purpose of the study is to measure the relationship between lifestyle and accident risk, and to identify specific high-risk and low-risk groups. Lifestyle is measured through a questionnaire, where 20-year-olds describe themselves and how often they deal with a large number of different activities, like sports, music, movies, reading, cars and driving, political engagement, etc. They also report their involvement in traffic accidents. With a principal component analysis followed by a cluster analysis, lifestyle profiles are defined. These profiles are finally correlated to accidents, which makes it possible to define high-risk and low-risk groups. The cluster analysis defined 15 clusters including four high-risk groups with an average overrisk of 150% and two low-risk groups with an average underrisk of 75%. The results are discussed from two perspectives. The first is the importance of theoretical understanding of the contribution of lifestyle factors to young drivers' high accident risk. The second is how the findings could be used in practical road safety measures, like education, campaigns, etc.

Circuit board accident--organizational dimension hidden by prescribed safety.

PubMed

de Almeida, Ildeberto Muniz; Buoso, Eduardo; do Amaral Dias, Maria Dionísia; Vilela, Rodolfo Andrade Gouveia

2012-01-01

This study analyzes an accident in which two maintenance workers suffered severe burns while replacing a circuit breaker panel in a steel mill, following model of analysis and prevention of accidents (MAPA) developed with the objective of enlarging the perimeter of interventions and contributing to deconstruction of blame attribution practices. The study was based on materials produced by a health service team in an in-depth analysis of the accident. The analysis shows that decisions related to system modernization were taken without considering their implications in maintenance scheduling and creating conflicts of priorities and of interests between production and safety; and also reveals that the lack of a systemic perspective in safety management was its principal failure. To explain the accident as merely non-fulfillment of idealized formal safety rules feeds practices of blame attribution supported by alibi norms and inhibits possible prevention. In contrast, accident analyses undertaken in worker health surveillance services show potential to reveal origins of these events incubated in the history of the system ignored in practices guided by the traditional paradigm.

Potential safety benefits of intelligent cruise control systems.

PubMed

Chira-Chavala, T; Yoo, S M

1994-04-01

Potential safety impact of a hypothetical intelligent cruise control system (ICCS) is evaluated in terms of changes in traffic accidents and some traffic operation characteristics affecting safety. The analysis of changes in traffic accidents is accomplished by in-depth examinations of police accident reports for four major counties in California. The evaluation of changes in traffic operation characteristics affecting safety is accomplished by vehicle simulation. The accident analysis reveals that the use of the hypothetical ICCS could potentially reduce traffic accidents by up to 7.5%. Preliminary vehicle simulation results based on a 10-vehicle convoy indicate that the use of the hypothetical ICCS could reduce frequencies of hard acceleration and deceleration, enhance speed harmonization among vehicles, and reduce incidence of "less-safe" headway.

Aircraft accidents.method of analysis

NASA Technical Reports Server (NTRS)

1937-01-01

This report is a revision of NACA-TR-357. It was prepared by the Committee on Aircraft Accidents. The purpose of this report is to provide a basis for the classification and comparison of aircraft accidents, both civil and military.

Measuring pedestrian volumes and conflicts. Volume 2, Accident prediction model

DOT National Transportation Integrated Search

1987-12-01

This final report presents the findings, conclusions, and recommendations of the study conducted to model pedestrian/vehicle accidents. A group-type analysis approach for the prediction of pedestrian/vehicle accidents using pedestrian/vehicle conflic...

Risk of Occupational Accidents in Workers with Obstructive Sleep Apnea: Systematic Review and Meta-analysis

PubMed Central

Garbarino, Sergio; Guglielmi, Ottavia; Sanna, Antonio; Mancardi, Gian Luigi; Magnavita, Nicola

2016-01-01

Study Objectives: Obstructive sleep apnea (OSA) is the single most important preventable medical cause of excessive daytime sleepiness (EDS) and driving accidents. OSA may also adversely affect work performance through a decrease in productivity, and an increase in the injury rate. Nevertheless, no systematic review and meta-analysis of the relationship between OSA and work accidents has been performed thus far. Methods: PubMed, PsycInfo, Scopus, Web of Science, and Cochrane Library were searched. Out of an initial list of 1,099 papers, 10 studies (12,553 participants) were eligible for our review, and 7 of them were included in the meta-analysis. The overall effects were measured by odds ratios (OR) and 95% confidence intervals (CI). An assessment was made of the methodological quality of the studies. Moderator analysis and funnel plot analysis were used to explore the sources of between-study heterogeneity. Results: Compared to controls, the odds of work accident was found to be nearly double in workers with OSA (OR = 2.18; 95% CI = 1.53–3.10). Occupational driving was associated with a higher effect size. Conclusions: OSA is an underdiagnosed nonoccupational disease that has a strong adverse effect on work accidents. The nearly twofold increased odds of work accidents in subjects with OSA calls for workplace screening in selected safety-sensitive occupations. Commentary: A commentary on this article appears in this issue on page 1171. Citation: Garbarino S, Guglielmi O, Sanna A, Mancardi GL, Magnavita N. Risk of occupational accidents in workers with obstructive sleep apnea: systematic review and meta-analysis. SLEEP 2016;39(6):1211–1218. PMID:26951401

Application of 3D documentation and geometric reconstruction methods in traffic accident analysis: with high resolution surface scanning, radiological MSCT/MRI scanning and real data based animation.

PubMed

Buck, Ursula; Naether, Silvio; Braun, Marcel; Bolliger, Stephan; Friederich, Hans; Jackowski, Christian; Aghayev, Emin; Christe, Andreas; Vock, Peter; Dirnhofer, Richard; Thali, Michael J

2007-07-20

The examination of traffic accidents is daily routine in forensic medicine. An important question in the analysis of the victims of traffic accidents, for example in collisions between motor vehicles and pedestrians or cyclists, is the situation of the impact. Apart from forensic medical examinations (external examination and autopsy), three-dimensional technologies and methods are gaining importance in forensic investigations. Besides the post-mortem multi-slice computed tomography (MSCT) and magnetic resonance imaging (MRI) for the documentation and analysis of internal findings, highly precise 3D surface scanning is employed for the documentation of the external body findings and of injury-inflicting instruments. The correlation of injuries of the body to the injury-inflicting object and the accident mechanism are of great importance. The applied methods include documentation of the external and internal body and the involved vehicles and inflicting tools as well as the analysis of the acquired data. The body surface and the accident vehicles with their damages were digitized by 3D surface scanning. For the internal findings of the body, post-mortem MSCT and MRI were used. The analysis included the processing of the obtained data to 3D models, determination of the driving direction of the vehicle, correlation of injuries to the vehicle damages, geometric determination of the impact situation and evaluation of further findings of the accident. In the following article, the benefits of the 3D documentation and computer-assisted, drawn-to-scale 3D comparisons of the relevant injuries with the damages to the vehicle in the analysis of the course of accidents, especially with regard to the impact situation, are shown on two examined cases.

Longitudinal analysis of categorical epidemiological data: a study of Three Mile Island.

PubMed

Fienberg, S E; Bromet, E J; Follmann, D; Lambert, D; May, S M

1985-11-01

The accident at the Three Mile Island nuclear power plant in 1979 led to an unprecedented set of events with potentially life threatening implications. This paper focusses on the analysis of a longitudinal study of the psychological well-being of the mothers of young children living within 10 miles of the plant. The initial analyses of the data utilize loglinear/logit model techniques from the contingency table literature, and involve the fitting of a sequence of logit models. The inadequancies of these analyses are noted, and a new class of mixture models for logistic response structures is introduced to overcome the noted shortcomings. The paper includes a brief outline of the methodology relevant for the fitting of these models using the method of maximum likelihood, and then the model is applied to the TMI data. The paper concludes with a discussion of some of the substantive implications of the mixture model analysis.

The effects of aircraft certification rules on general aviation accidents

NASA Astrophysics Data System (ADS)

Anderson, Carolina Lenz

The purpose of this study was to analyze the frequency of general aviation airplane accidents and accident rates on the basis of aircraft certification to determine whether or not differences in aircraft certification rules had an influence on accidents. In addition, the narrative cause descriptions contained within the accident reports were analyzed to determine whether there were differences in the qualitative data for the different certification categories. The certification categories examined were: Federal Aviation Regulations Part 23, Civil Air Regulations 3, Light Sport Aircraft, and Experimental-Amateur Built. The accident causes examined were those classified as: Loss of Control, Controlled Flight into Terrain, Engine Failure, and Structural Failure. Airworthiness certification categories represent a wide diversity of government oversight. Part 23 rules have evolved from the initial set of simpler design standards and have progressed into a comprehensive and strict set of rules to address the safety issues of the more complex airplanes within the category. Experimental-Amateur Built airplanes have the least amount of government oversight and are the fastest growing segment. The Light Sport Aircraft category is a more recent certification category that utilizes consensus standards in the approval process. Civil Air Regulations 3 airplanes were designed and manufactured under simpler rules but modifying these airplanes has become lengthy and expensive. The study was conducted using a mixed methods methodology which involves both quantitative and qualitative elements. A Chi-Square test was used for a quantitative analysis of the accident frequency among aircraft certification categories. Accident rate analysis of the accidents among aircraft certification categories involved an ANCOVA test. The qualitative component involved the use of text mining techniques for the analysis of the narrative cause descriptions contained within the accident reports. The Chi-Square test indicated that there was no significant difference in the number of accidents among the different certification categories when either Controlled Flight into Terrain or Structural Failure was listed as cause. However, there was a significant difference in the frequency of accidents with regard to Loss of Control and Engine Failure accidents. The results of the ANCOVA test indicated that there was no significant difference in the accident rate with regard to Loss of Control, Controlled Flight into Terrain, or Structural Failure accidents. There was, however, a significant difference in Engine Failure accidents between Experimental-Amateur Built and the other categories.The text mining analysis of the narrative causes of Loss of Control accidents indicated that only the Civil Air Regulations 3 category airplanes had clusters of words associated with visual flight into instrument meteorological conditions. Civil Air Regulations 3 airplanes were designed and manufactured prior to the 1960s and in most cases have not been retrofitted to take advantage of newer technologies that could help prevent Loss of Control accidents. The study indicated that General Aviation aircraft certification rules do not have a statistically significant effect on aircraft accidents except for Loss of Control and Engine Failure. According to the literature, government oversight could have become an obstacle in the implementation of safety enhancing equipment that could reduce Loss of Control accidents. Oversight should focus on ensuring that Experimental-Amateur Built aircraft owners perform a functional test that could prevent some of the Engine Failure accidents.

Information Services at the Nuclear Safety Analysis Center.

ERIC Educational Resources Information Center

Simard, Ronald

This paper describes the operations of the Nuclear Safety Analysis Center. Established soon after an accident at the Three Mile Island nuclear power plant near Harrisburg, Pennsylvania, its efforts were initially directed towards a detailed analysis of the accident. Continuing functions include: (1) the analysis of generic nuclear safety issues,…

Recent plant studies using Victoria 2.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

BIXLER,NATHAN E.; GASSER,RONALD D.

2000-03-08

VICTORIA 2.0 is a mechanistic computer code designed to analyze fission product behavior within the reactor coolant system (RCS) during a severe nuclear reactor accident. It provides detailed predictions of the release of radioactive and nonradioactive materials from the reactor core and transport and deposition of these materials within the RCS and secondary circuits. These predictions account for the chemical and aerosol processes that affect radionuclide behavior. VICTORIA 2.0 was released in early 1999; a new version VICTORIA 2.1, is now under development. The largest improvements in VICTORIA 2.1 are connected with the thermochemical database, which is being revised andmore » expanded following the recommendations of a peer review. Three risk-significant severe accident sequences have recently been investigated using the VICTORIA 2.0 code. The focus here is on how various chemistry options affect the predictions. Additionally, the VICTORIA predictions are compared with ones made using the MELCOR code. The three sequences are a station blackout in a GE BWR and steam generator tube rupture (SGTR) and pump-seal LOCA sequences in a 3-loop Westinghouse PWR. These sequences cover a range of system pressures, from fully depressurized to full system pressure. The chief results of this study are the fission product fractions that are retained in the core, RCS, secondary, and containment and the fractions that are released into the environment.« less

Bayesian-network-based safety risk assessment for steel construction projects.

PubMed

Leu, Sou-Sen; Chang, Ching-Miao

2013-05-01

There are four primary accident types at steel building construction (SC) projects: falls (tumbles), object falls, object collapse, and electrocution. Several systematic safety risk assessment approaches, such as fault tree analysis (FTA) and failure mode and effect criticality analysis (FMECA), have been used to evaluate safety risks at SC projects. However, these traditional methods ineffectively address dependencies among safety factors at various levels that fail to provide early warnings to prevent occupational accidents. To overcome the limitations of traditional approaches, this study addresses the development of a safety risk-assessment model for SC projects by establishing the Bayesian networks (BN) based on fault tree (FT) transformation. The BN-based safety risk-assessment model was validated against the safety inspection records of six SC building projects and nine projects in which site accidents occurred. The ranks of posterior probabilities from the BN model were highly consistent with the accidents that occurred at each project site. The model accurately provides site safety-management abilities by calculating the probabilities of safety risks and further analyzing the causes of accidents based on their relationships in BNs. In practice, based on the analysis of accident risks and significant safety factors, proper preventive safety management strategies can be established to reduce the occurrence of accidents on SC sites. Copyright © 2013 Elsevier Ltd. All rights reserved.

Accidents in Germany: evaluation of the german telephone health survey 2004.

PubMed

Saß, Anke-Christine

2008-09-01

In the year 2006 there were over 19 000 fatal accidents in Germany and estimates put the number of accidental injuries at more than 8 million. Detailed information on the pattern of accidents is indispensable for the definition of priorities in accident prevention. The German Telephone Health Survey 2004 provides representative cross-sectional data on the health of German residents from 18 years of age (n = 7341). Questions on the prevalence of accidents (13 items) were selected for analysis. Every tenth interviewee reported being injured in an accident in the previous 12 months. Men, particularly young men, are at greater risk of accidents than women. Almost one third of all accidents occurred at home. Social status had no influence on the probability of having an accident, but did affect where the accident happened. The survey yields information on the overall pattern of non-fatal accidents in Germany. The data point to target groups for accident prevention measures.

[An analysis of industrial accidents in the working field with a particular emphasis on repeated accidents].

PubMed

Wakisaka, I; Yanagihashi, T; Tomari, T; Sato, M

1990-03-01

The present study is based on an analysis of routinely submitted reports of occupational accidents experienced by the workers of industrial enterprises under the jurisdiction of Kagoshima Labor Standard Office during a 5-year period 1983 to 1987. Officially notified injuries serious enough to keep employees away from their job for work at least 4 days were utilized in this study. Data was classified so as to give an observed frequency distribution for workers having any specified number of accidents. Also, the accident rate which is an indicator of the risk of accident was compared among different occupations, between age groups and between the sexes. Results obtained are as follows; 1) For the combined total of 6,324 accident cases for 8 types of occupation (Construction, Transportation, Mining & Quarrying, Forestry, Food manufacture, Lumber & Woodcraft, Manufacturing industry and Other business), the number of those who had at least one accident was 6,098, of which 5,837 were injured only once, 208 twice, 21 three times and 2 four times. When occupation type was fixed, however, the number of workers having one, two, three and four times of accidents were 5,895, 182, 19 and 2, respectively. This suggests that some workers are likely to have experienced repeated accidents in more than one type of occupation.(ABSTRACT TRUNCATED AT 250 WORDS)

Human factors analysis and classification system-HFACS.

DOT National Transportation Integrated Search

2000-02-01

Human error has been implicated in 70 to 80% of all civil and military aviation accidents. Yet, most accident : reporting systems are not designed around any theoretical framework of human error. As a result, most : accident databases are not conduci...

Development of a bespoke human factors taxonomy for gliding accident analysis and its revelations about highly inexperienced UK glider pilots.

PubMed

Jarvis, Steve; Harris, Don

2010-02-01

Low-hours solo glider pilots have a high risk of accidents compared to more experienced pilots. Numerous taxonomies for causal accident analysis have been produced for powered aviation but none of these is suitable for gliding, so a new taxonomy was required. A human factors taxonomy specifically for glider operations was developed and used to analyse all UK gliding accidents from 2002 to 2006 for their overall causes as well as factors specific to low hours pilots. Fifty-nine categories of pilot-related accident causation emerged, which were formed into progressively larger categories until four overall human factors groups were arrived at: 'judgement'; 'handling'; 'strategy'; 'attention'. 'Handling' accounted for a significantly higher proportion of injuries than other categories. Inexperienced pilots had considerably more accidents in all categories except 'strategy'. Approach control (path judgement, airbrake and speed handling) as well as landing flare misjudgement were chiefly responsible for the high accident rate in early solo glider pilots. Statement of Relevance: This paper uses extant accident data to produce a taxonomy of underlying human factors causes to analyse gliding accidents and identify the specific causes associated with low hours pilots. From this specific, well-targeted remedial measures can be identified.

Scenario analysis of freight vehicle accident risks in Taiwan.

PubMed

Tsai, Ming-Chih; Su, Chien-Chih

2004-07-01

This study develops a quantitative risk model by utilizing Generalized Linear Interactive Model (GLIM) to analyze the major freight vehicle accidents in Taiwan. Eight scenarios are established by interacting three categorical variables of driver ages, vehicle types and road types, each of which contains two levels. The database that consists of 2043 major accidents occurring between 1994 and 1998 in Taiwan is utilized to fit and calibrate the model parameters. The empirical results indicate that accident rates of freight vehicles in Taiwan were high in the scenarios involving trucks and non-freeway systems, while; accident consequences were severe in the scenarios involving mature drivers or non-freeway systems. Empirical evidences also show that there is no significant relationship between accident rates and accident consequences. This is to stress that safety studies that describe risk merely as accident rates rather than the combination of accident rates and consequences by definition might lead to biased risk perceptions. Finally, the study recommends using number of vehicle as an alternative of traffic exposure in commercial vehicle risk analysis. The merits of this would be that it is simple and thus reliable; meanwhile, the resulted risk that is termed as fatalities per vehicle could provide clear and direct policy implications for insurance practices and safety regulations.

Reliability and Probabilistic Risk Assessment - How They Play Together

NASA Technical Reports Server (NTRS)

Safie, Fayssal; Stutts, Richard; Huang, Zhaofeng

2015-01-01

Since the Space Shuttle Challenger accident in 1986, NASA has extensively used probabilistic analysis methods to assess, understand, and communicate the risk of space launch vehicles. Probabilistic Risk Assessment (PRA), used in the nuclear industry, is one of the probabilistic analysis methods NASA utilizes to assess Loss of Mission (LOM) and Loss of Crew (LOC) risk for launch vehicles. PRA is a system scenario based risk assessment that uses a combination of fault trees, event trees, event sequence diagrams, and probability distributions to analyze the risk of a system, a process, or an activity. It is a process designed to answer three basic questions: 1) what can go wrong that would lead to loss or degraded performance (i.e., scenarios involving undesired consequences of interest), 2) how likely is it (probabilities), and 3) what is the severity of the degradation (consequences). Since the Challenger accident, PRA has been used in supporting decisions regarding safety upgrades for launch vehicles. Another area that was given a lot of emphasis at NASA after the Challenger accident is reliability engineering. Reliability engineering has been a critical design function at NASA since the early Apollo days. However, after the Challenger accident, quantitative reliability analysis and reliability predictions were given more scrutiny because of their importance in understanding failure mechanism and quantifying the probability of failure, which are key elements in resolving technical issues, performing design trades, and implementing design improvements. Although PRA and reliability are both probabilistic in nature and, in some cases, use the same tools, they are two different activities. Specifically, reliability engineering is a broad design discipline that deals with loss of function and helps understand failure mechanism and improve component and system design. PRA is a system scenario based risk assessment process intended to assess the risk scenarios that could lead to a major/top undesirable system event, and to identify those scenarios that are high-risk drivers. PRA output is critical to support risk informed decisions concerning system design. This paper describes the PRA process and the reliability engineering discipline in detail. It discusses their differences and similarities and how they work together as complementary analyses to support the design and risk assessment processes. Lessons learned, applications, and case studies in both areas are also discussed in the paper to demonstrate and explain these differences and similarities.

Incorporating real-time traffic and weather data to explore road accident likelihood and severity in urban arterials.

PubMed

Theofilatos, Athanasios

2017-06-01

The effective treatment of road accidents and thus the enhancement of road safety is a major concern to societies due to the losses in human lives and the economic and social costs. The investigation of road accident likelihood and severity by utilizing real-time traffic and weather data has recently received significant attention by researchers. However, collected data mainly stem from freeways and expressways. Consequently, the aim of the present paper is to add to the current knowledge by investigating accident likelihood and severity by exploiting real-time traffic and weather data collected from urban arterials in Athens, Greece. Random Forests (RF) are firstly applied for preliminary analysis purposes. More specifically, it is aimed to rank candidate variables according to their relevant importance and provide a first insight on the potential significant variables. Then, Bayesian logistic regression as well finite mixture and mixed effects logit models are applied to further explore factors associated with accident likelihood and severity respectively. Regarding accident likelihood, the Bayesian logistic regression showed that variations in traffic significantly influence accident occurrence. On the other hand, accident severity analysis revealed a generally mixed influence of traffic variations on accident severity, although international literature states that traffic variations increase severity. Lastly, weather parameters did not find to have a direct influence on accident likelihood or severity. The study added to the current knowledge by incorporating real-time traffic and weather data from urban arterials to investigate accident occurrence and accident severity mechanisms. The identification of risk factors can lead to the development of effective traffic management strategies to reduce accident occurrence and severity of injuries in urban arterials. Copyright © 2017 Elsevier Ltd and National Safety Council. All rights reserved.

National and regional analysis of road accidents in Spain.

PubMed

Tolón-Becerra, A; Lastra-Bravo, X; Flores-Parra, I

2013-01-01

In Spain, the absolute fatality figures decreased almost 50 percent between 1998 and 2009. Despite this great effort, road mortality is still of great concern to political authorities. Further progress requires efficient road safety policy based on an optimal set of measures and targets that consider the initial conditions and characteristics in each region. This study attempts to analyze road accidents in Spain and its provinces in time and space during 1998-2009. First, we analyzed daily, monthly, and nationwide (NUTS 0) development of road accidents, the correlation between logarithmic transformations of road accidents and territorial and socioeconomic variables, the causality by simple linear regression of road accidents and territorial and socioeconomic variables, and preliminary frequency by fast Fourier transform. Then we analyzed the annual trend in accidents in the Spanish provinces (NUTS 3) and found a correlation between the logarithmic transformations of the mortality rate, fatalities per fatal accident, and accidents resulting in injuries per inhabitant variables and population, population density, gross domestic product (GDP), length of road network, and area. Finally, causality was analyzed by simple linear regression. The most outstanding results were the negative correlation between mortality rate and population density in Spanish provinces, which has increased over time, and that road accidents in Spain have an approximate periodicity of 57 days. The fast Fourier transform analysis of road accident frequency in Spain was useful in identifying the periodic, harmonic components of accidents and casualties. The periodicity observed both for the period 1998-2009 and by year showed that the highest intensity in road accidents was bimonthly, despite the lower number of accidents and casualties in the spectra of amplitude and power and efforts to reduce the intensity and concentration during off-season travel (summer and December).

A Content Analysis of News Media Coverage of the Accident at Three Mile Island.

ERIC Educational Resources Information Center

Stephens, Mitchell; Edison, Nadyne G.

A study was conducted for the President's Commission on the Accident at Three Mile Island to analyze coverage of the accident by ten news organizations: two wire services, three commercial television networks, and five daily newspapers. Copies of all stories and transcripts of news programs during the first week of the accident were examined from…

Is "Safety-in-numbers" theory applies to the pattern of pedestrian accidents in Seoul, South Korea.

NASA Astrophysics Data System (ADS)

Choi, Y.; Yoon, H.

2016-12-01

Every year, about 1.25 million people die of vehicle-related accidents, among which half are pedestrians with higher vulnerability: pedestrian, cyclists and motorcyclist (World Health Organization, 2016). This urges city governments in the world to strive for pedestrian safety and to apply diverse theories to transportation planning and design. The common belief is that the number of pedestrian accidents is directly and positively associated with the volume of pedestrian, however, another hypothesis, called "safety-in-numbers" effect, tells an opposite story in that accident rates declines with increase of the volume of pedestrian. In this study, we examine first, whether the safety-in-numbers theory applies to the pattern of pedestrian accidents in Seoul, and second, further investigate environmental factors that are associated with the pedestrian safety. On the first count, we use geospatial statistical analyses of the multi-year pedestrian accident data collected by Korea Road Traffic Authority (KoRoad) and the pedestrian volume data collected by SK Telecom (SKT). With Kernel Density Estimation and Bivariate Local Moran's I, we identify spatial clustering of pedestrian accidents in the city, and examine whether those locations match with concentrations of pedestrian volume. On the second count, we use statistical analysis, tobit, poisson and negative binomial regression to investigate relationships between pedestrian volume and number of pedestrian accident for the two types of geographic areas by the results of the aforementioned analysis; Area 1- locations of high volume of pedestrian with high number of accident, Area 2- locations of high volume of pedestrian with low number of accident. For environmental factors potentially explaining pedestrian accidents, we include land use composition, number of traffic lanes, crosswalk presence, pedestrian signal, traffic island and sidewalk width in our analysis. This research will be valuable in city governments' decision making with planning guidelines and political protocols for making safer pedestrian environment.

Bus accident analysis of routes with/without bus priority.

PubMed

Goh, Kelvin Chun Keong; Currie, Graham; Sarvi, Majid; Logan, David

2014-04-01

This paper summarises findings on road safety performance and bus-involved accidents in Melbourne along roads where bus priority measures had been applied. Results from an empirical analysis of the accident types revealed significant reduction in the proportion of accidents involving buses hitting stationary objects and vehicles, which suggests the effect of bus priority in addressing manoeuvrability issues for buses. A mixed-effects negative binomial (MENB) regression and back-propagation neural network (BPNN) modelling of bus accidents considering wider influences on accident rates at a route section level also revealed significant safety benefits when bus priority is provided. Sensitivity analyses done on the BPNN model showed general agreement in the predicted accident frequency between both models. The slightly better performance recorded by the MENB model results suggests merits in adopting a mixed effects modelling approach for accident count prediction in practice given its capability to account for unobserved location and time-specific factors. A major implication of this research is that bus priority in Melbourne's context acts to improve road safety and should be a major consideration for road management agencies when implementing bus priority and road schemes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Nuclear power and probabilistic safety assessment (PSA): past through future applications

NASA Astrophysics Data System (ADS)

Stamatelatos, M. G.; Moieni, P.; Everline, C. J.

1995-03-01

Nuclear power reactor safety in the United States is about to enter a new era -- an era of risk- based management and risk-based regulation. First, there was the age of `prescribed safety assessment,' during which a series of design-basis accidents in eight categories of severity, or classes, were postulated and analyzed. Toward the end of that era, it was recognized that `Class 9,' or `beyond design basis,' accidents would need special attention because of the potentially severe health and financial consequences of these accidents. The accident at Three Mile Island showed that sequences of low-consequence, high-frequency events and human errors can be much more risk dominant than the Class 9 accidents. A different form of safety assessment, PSA, emerged and began to gain ground against the deterministic safety establishment. Eventually, this led to the current regulatory requirements for individual plant examinations (IPEs). The IPEs can serve as a basis for risk-based regulation and management, a concept that may ultimately transform the U.S. regulatory process from its traditional deterministic foundations to a process predicated upon PSA. Beyond the possibility of a regulatory environment predicated upon PSA lies the possibility of using PSA as the foundation for managing daily nuclear power plant operations.

1997 Oregon state highway accident rate tables

DOT National Transportation Integrated Search

1998-08-01

The three parts of this report are: : I Results of Analysis containing comparative tables and the Signed Route on Highway list, : II Five year accident rate data by highway sections, : III A summary of this year's fatal traffic accidents. : The first...

Modeling traffic accidents at signalized intersections in the city of Norfolk, VA.

DOT National Transportation Integrated Search

2010-12-31

This study was an attempt to apply a proactive approach using traffic pattern and signalized intersection characteristics to predict accident rates at signalized intersections in a citys arterial network. An earlier analysis of accident data at se...

Analysis of Child-related Road Traffic Accidents in Vietnam

NASA Astrophysics Data System (ADS)

Vu, Anh Tuan; Nguyen, Dinh Vinh Man

2018-04-01

In recent years, the number of road traffic accidents, fatalities and injuries have been decreasing, but the figures of children road traffic accidents have been increasing in Ho Chi Minh City of Vietnam. This fact strongly calls for implementing effective solutions to improve traffic safety for children by the local government. This paper presents the trends, patterns and causes of road traffic accidents involving children based on the analysis of road traffic accident data over the period 2010-2015 and the video-based observations of road traffic law violations at 15 typical school gates and 10 typical roads. The results could be useful for the city government to formulate solutions to effectively improve traffic safety for children in Ho Chi Minh City and other cities in Vietnam.

Reliability verification of vehicle speed estimate method in forensic videos.

PubMed

Kim, Jong-Hyuk; Oh, Won-Taek; Choi, Ji-Hun; Park, Jong-Chan

2018-06-01

In various types of traffic accidents, including car-to-car crash, vehicle-pedestrian collision, and hit-and-run accident, driver overspeed is one of the critical issues of traffic accident analysis. Hence, analysis of vehicle speed at the moment of accident is necessary. The present article proposes a vehicle speed estimate method (VSEM) applying a virtual plane and a virtual reference line to a forensic video. The reliability of the VSEM was verified by comparing the results obtained by applying the VSEM to videos from a test vehicle driving with a global positioning system (GPS)-based Vbox speed. The VSEM verified by these procedures was applied to real traffic accident examples to evaluate the usability of the VSEM. Copyright © 2018 Elsevier B.V. All rights reserved.

Explorative spatial analysis of traffic accident statistics and road mortality among the provinces of Turkey.

PubMed

Erdogan, Saffet

2009-10-01

The aim of the study is to describe the inter-province differences in traffic accidents and mortality on roads of Turkey. Two different risk indicators were used to evaluate the road safety performance of the provinces in Turkey. These indicators are the ratios between the number of persons killed in road traffic accidents (1) and the number of accidents (2) (nominators) and their exposure to traffic risk (denominator). Population and the number of registered motor vehicles in the provinces were used as denominators individually. Spatial analyses were performed to the mean annual rate of deaths and to the number of fatal accidents that were calculated for the period of 2001-2006. Empirical Bayes smoothing was used to remove background noise from the raw death and accident rates because of the sparsely populated provinces and small number of accident and death rates of provinces. Global and local spatial autocorrelation analyses were performed to show whether the provinces with high rates of deaths-accidents show clustering or are located closer by chance. The spatial distribution of provinces with high rates of deaths and accidents was nonrandom and detected as clustered with significance of P<0.05 with spatial autocorrelation analyses. Regions with high concentration of fatal accidents and deaths were located in the provinces that contain the roads connecting the Istanbul, Ankara, and Antalya provinces. Accident and death rates were also modeled with some independent variables such as number of motor vehicles, length of roads, and so forth using geographically weighted regression analysis with forward step-wise elimination. The level of statistical significance was taken as P<0.05. Large differences were found between the rates of deaths and accidents according to denominators in the provinces. The geographically weighted regression analyses did significantly better predictions for both accident rates and death rates than did ordinary least regressions, as indicated by adjusted R(2) values. Geographically weighted regression provided values of 0.89-0.99 adjusted R(2) for death and accident rates, compared with 0.88-0.95, respectively, by ordinary least regressions. Geographically weighted regression has the potential to reveal local patterns in the spatial distribution of rates, which would be ignored by the ordinary least regression approach. The application of spatial analysis and modeling of accident statistics and death rates at provincial level in Turkey will help to identification of provinces with outstandingly high accident and death rates. This could help more efficient road safety management in Turkey.

Road profiling of traffic accidents in Jos, Nigeria, 1995-1999.

PubMed

Bombom, Leonard S; Edino, Marcus O

2009-09-01

Road traffic accident data in Nigeria generally lack exact coordinate information. Accident analysis is, therefore, restricted to aggregate data on trends, magnitude and temporal dimensions. This article addresses the road accident problem in Jos between 1995 and 1999 through a road profiling approach. Results show that four gateway routes, seven multi-lane roadways (including two gateway routes) and seven road intersections accounted for 84% of all traffic accidents, 84% of injured casualties and 88% of fatalities. This approach allows for quantification of impacts of controlling for accidents by deliberate profiling of roads for close monitoring and policing. For example, reducing accident counts and fatalities by 50% each on gateway routes will amount to approximately 35 and 40% reduction in accident and fatality counts, respectively. Countermeasures must consider these roadways and intersections as important inputs in their accidents and casualty reduction targets.

Indonesian railway accidents--utilizing Human Factors Analysis and Classification System in determining potential contributing factors.

PubMed

Iridiastadi, Hardianto; Ikatrinasari, Zulfa Fitri

2012-01-01

The prevalence of Indonesian railway accidents has not been declining, with hundreds of fatalities reported in the past decade. As an effort to help the National Transportation Safety Committee (NTSC), this study was conducted that aimed at understanding factors that might have contributed to the accidents. Human Factors Analysis and Classification System (HFACS) was utilized for this purpose. A total of nine accident reports (provided by the Indonesian NTSC) involving fatalities were studied using the technique. Results of this study indicated 72 factors that were closely related to the accidents. Of these, roughly 22% were considered as operator acts while about 39% were related to preconditions for operator acts. Supervisory represented 14% of the factors, and the remaining (about 25%) were associated with organizational factors. It was concluded that, while train drivers indeed played an important role in the accidents, interventions solely directed toward train drivers may not be adequate. A more comprehensive approach in minimizing the accidents should be conducted that addresses all the four aspects of HFACS.

How perceptions of experience-based analysis influence explanations of work accidents.

PubMed

Mbaye, Safiétou; Kouabenan, Dongo Rémi

2013-12-01

This article looks into how perceptions of experience-based analysis (EBA) influence causal explanations of accidents given by managers and workers in the chemical industry (n=409) and in the nuclear industry (n=222). The approach is based on the model of naive explanations of accidents (Kouabenan, 1999, 2006, 2009), which recommends taking into account explanations of accidents spontaneously given by individuals, including laypersons, not only to better understand why accidents occur but also to design and implement the most appropriate prevention measures. The study reported here describes the impact of perceptions about EBA (perceived effectiveness, personal commitment, and the feeling of being involved in EBA practices) on managers' and workers' explanations of accidents likely to occur at the workplace. The results indicated that both managers and workers made more internal explanations than external ones when they perceived EBA positively. Moreover, the more the participants felt involved in EBA, were committed to it, and judged it effective, the more they explained accidents in terms of factors internal to the workers. Recommendations are proposed for reducing defensive reactions, increasing personal commitment to EBA, and improving EBA effectiveness. © 2013.

The Driver Behaviour Questionnaire as accident predictor; A methodological re-meta-analysis.

PubMed

Af Wåhlberg, A E; Barraclough, P; Freeman, J

2015-12-01

The Manchester Driver Behaviour Questionnaire (DBQ) is the most commonly used self-report tool in traffic safety research and applied settings. It has been claimed that the violation factor of this instrument predicts accident involvement, which was supported by a previous meta-analysis. However, that analysis did not test for methodological effects, or include unpublished results. The present study re-analysed studies on prediction of accident involvement from DBQ factors, including lapses, and many unpublished effects. Tests of various types of dissemination bias and common method variance were undertaken. Outlier analysis showed that some effects were probably not reliable data, but excluding them did not change the results. For correlations between violations and crashes, tendencies for published effects to be larger than unpublished ones and for effects to decrease over time were observed, but were not significant. Also, using the mean of accidents as proxy for effect indicated that studies where effects for violations are not reported have smaller effect sizes. These differences indicate dissemination bias. Studies using self-reported accidents as dependent variables had much larger effects than those using recorded accident data. Also, zero-order correlations were larger than partial correlations controlled for exposure. Similarly, violations/accidents effects were strong only when there was also a strong correlation between accidents and exposure. Overall, the true effect is probably very close to zero (r<.07) for violations versus traffic accident involvement, depending upon which tendencies are controlled for. Methodological factors and dissemination bias have inflated the published effect sizes of the DBQ. Strong evidence of various artefactual effects is apparent. A greater level of care should be taken if the DBQ continues to be used in traffic safety research. Also, validation of self-reports should be more comprehensive in the future, taking into account the possibility of common method variance. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

Transcriptome Analysis in Venom Gland of the Predatory Giant Ant Dinoponera quadriceps: Insights into the Polypeptide Toxin Arsenal of Hymenopterans

PubMed Central

Chong, Cheong-Meng; Leung, Siu Wai; Prieto-da-Silva, Álvaro R. B.; Havt, Alexandre; Quinet, Yves P.; Martins, Alice M. C.; Lee, Simon M. Y.; Rádis-Baptista, Gandhi

2014-01-01

Background Dinoponera quadriceps is a predatory giant ant that inhabits the Neotropical region and subdues its prey (insects) with stings that deliver a toxic cocktail of molecules. Human accidents occasionally occur and cause local pain and systemic symptoms. A comprehensive study of the D. quadriceps venom gland transcriptome is required to advance our knowledge about the toxin repertoire of the giant ant venom and to understand the physiopathological basis of Hymenoptera envenomation. Results We conducted a transcriptome analysis of a cDNA library from the D. quadriceps venom gland with Sanger sequencing in combination with whole-transcriptome shotgun deep sequencing. From the cDNA library, a total of 420 independent clones were analyzed. Although the proportion of dinoponeratoxin isoform precursors was high, the first giant ant venom inhibitor cysteine-knot (ICK) toxin was found. The deep next generation sequencing yielded a total of 2,514,767 raw reads that were assembled into 18,546 contigs. A BLAST search of the assembled contigs against non-redundant and Swiss-Prot databases showed that 6,463 contigs corresponded to BLASTx hits and indicated an interesting diversity of transcripts related to venom gene expression. The majority of these venom-related sequences code for a major polypeptide core, which comprises venom allergens, lethal-like proteins and esterases, and a minor peptide framework composed of inter-specific structurally conserved cysteine-rich toxins. Both the cDNA library and deep sequencing yielded large proportions of contigs that showed no similarities with known sequences. Conclusions To our knowledge, this is the first report of the venom gland transcriptome of the New World giant ant D. quadriceps. The glandular venom system was dissected, and the toxin arsenal was revealed; this process brought to light novel sequences that included an ICK-folded toxins, allergen proteins, esterases (phospholipases and carboxylesterases), and lethal-like toxins. These findings contribute to the understanding of the ecology, behavior and venomics of hymenopterans. PMID:24498135

[Accidents in travellers - the hidden epidemic].

PubMed

Walz, Alexander; Hatz, Christoph

2013-06-01

The risk of malaria and other communicable diseases is well addressed in pre-travel advice. Accidents are usually less discussed. Thus, we aimed at assessing accident figures for the Swiss population, based on data of the register from 2004 to 2008 of the largest Swiss accident insurance organization (SUVA). More than 139'000 accidents over 5 years showed that 65 % of the accidents overseas are injuries, and 24 % are caused by poisoning or harm by cold, heat or air pressure. Most accidents happened during leisure activities or sports. More than one third of the non-lethal and more than 50 % of the fatal accidents happened in Asia. More than three-quarters of non-lethal accidents take place in people between 25 and 54 years. One out of 74 insured persons has an accident abroad per year. Despite of many analysis short-comings of the data set with regard to overseas travel, the figures document the underestimated burden of disease caused by accidents abroad and should affect the given pre-health advice.

Fukushima Accident: Sequence of Events and Lessons Learned

NASA Astrophysics Data System (ADS)

Morse, Edward C.

2011-10-01

The Fukushima Dai-Ichi nuclear power station suffered a devastating Richter 9.0 earthquake followed by a 14.0 m tsunami on 11 March 2011. The subsequent loss of power for emergency core cooling systems resulted in damage to the fuel in the cores of three reactors. The relief of pressure from the containment in these three reactors led to sufficient hydrogen gas release to cause explosions in the buildings housing the reactors. There was probably subsequent damage to a spent fuel pool of a fourth reactor caused by debris from one of these explosions. Resultant releases of fission product isotopes in air were significant and have been estimated to be in the 3 . 7 --> 6 . 3 ×1017 Bq range (~10 MCi) for 131I and 137Cs combined, or approximately one tenth that of the Chernobyl accident. A synopsis of the sequence of events leading up to this large release of radioactivity will be presented, along with likely scenarios for stabilization and site cleanup in the future. Some aspects of the isotope monitoring programs, both locally and at large, will also be discussed. An assessment of radiological health risk for the plant workers as well as the general public will also be presented. Finally, the impact of this accident on design and deployment of nuclear generating stations in the future will be discussed.

Human error analysis of commercial aviation accidents using the human factors analysis and classification system (HFACS)

DOT National Transportation Integrated Search

2001-02-01

The Human Factors Analysis and Classification System (HFACS) is a general human error framework : originally developed and tested within the U.S. military as a tool for investigating and analyzing the human : causes of aviation accidents. Based upon ...

Systemic accident analysis: examining the gap between research and practice.

PubMed

Underwood, Peter; Waterson, Patrick

2013-06-01

The systems approach is arguably the dominant concept within accident analysis research. Viewing accidents as a result of uncontrolled system interactions, it forms the theoretical basis of various systemic accident analysis (SAA) models and methods. Despite the proposed benefits of SAA, such as an improved description of accident causation, evidence within the scientific literature suggests that these techniques are not being used in practice and that a research-practice gap exists. The aim of this study was to explore the issues stemming from research and practice which could hinder the awareness, adoption and usage of SAA. To achieve this, semi-structured interviews were conducted with 42 safety experts from ten countries and a variety of industries, including rail, aviation and maritime. This study suggests that the research-practice gap should be closed and efforts to bridge the gap should focus on ensuring that systemic methods meet the needs of practitioners and improving the communication of SAA research. Copyright © 2013 Elsevier Ltd. All rights reserved.

Application of systems and control theory-based hazard analysis to radiation oncology.

PubMed

Pawlicki, Todd; Samost, Aubrey; Brown, Derek W; Manger, Ryan P; Kim, Gwe-Ya; Leveson, Nancy G

2016-03-01

Both humans and software are notoriously challenging to account for in traditional hazard analysis models. The purpose of this work is to investigate and demonstrate the application of a new, extended accident causality model, called systems theoretic accident model and processes (STAMP), to radiation oncology. Specifically, a hazard analysis technique based on STAMP, system-theoretic process analysis (STPA), is used to perform a hazard analysis. The STPA procedure starts with the definition of high-level accidents for radiation oncology at the medical center and the hazards leading to those accidents. From there, the hierarchical safety control structure of the radiation oncology clinic is modeled, i.e., the controls that are used to prevent accidents and provide effective treatment. Using STPA, unsafe control actions (behaviors) are identified that can lead to the hazards as well as causal scenarios that can lead to the identified unsafe control. This information can be used to eliminate or mitigate potential hazards. The STPA procedure is demonstrated on a new online adaptive cranial radiosurgery procedure that omits the CT simulation step and uses CBCT for localization, planning, and surface imaging system during treatment. The STPA procedure generated a comprehensive set of causal scenarios that are traced back to system hazards and accidents. Ten control loops were created for the new SRS procedure, which covered the areas of hospital and department management, treatment design and delivery, and vendor service. Eighty three unsafe control actions were identified as well as 472 causal scenarios that could lead to those unsafe control actions. STPA provides a method for understanding the role of management decisions and hospital operations on system safety and generating process design requirements to prevent hazards and accidents. The interaction of people, hardware, and software is highlighted. The method of STPA produces results that can be used to improve safety and prevent accidents and warrants further investigation.

Analysis for the Progressive Failure Response of Textile Composite Fuselage Frames

NASA Technical Reports Server (NTRS)

Johnson, Eric R.; Boitnott, Richard L. (Technical Monitor)

2002-01-01

A part of aviation accident mitigation is a crashworthy airframe structure, and an important measure of merit for a crashworthy structure is the amount of kinetic energy that can be absorbed in the crush of the structure. Prediction of the energy absorbed from finite element analyses requires modeling the progressive failure sequence. Progressive failure modes may include material degradation, fracture and crack growth, and buckling and collapse. The design of crashworthy airframe components will benefit from progressive failure analyses that have been validated by tests. The subject of this research is the development of a progressive failure analysis for a textile composite, circumferential fuselage frame subjected to a quasi-static, crash-type load. The test data for the frame are reported, and these data are used to develop and to validate methods for the progressive failure response.

CARDfile data base representativeness, Phase 1 : general characteristics including populations, vehicles, roads, and fatal accidents

DOT National Transportation Integrated Search

1988-08-01

This report details the results of an analysis performed to evaluate the : representativeness of the Crash Avoidance Research accident data base : (CARDfile). The accident records for 1983 and 1984 from six states (Indiana, : Maryland, Michigan, Penn...

CARDfile Data Base Representatives - Phase I: General Characteristics including Populations, Vehicles, Roads, and Fatal Accidents

DOT National Transportation Integrated Search

1985-12-01

This report details the results of an analysis performed to evaluate the representativeness of the Crash Avoidance Research accident data base (CARDfile). The accident records for 1983 and 1984 from six states (Indiana, Maryland, Michigan, Pennsylvan...

The Human Factors Analysis and Classification System : HFACS : final report.

DOT National Transportation Integrated Search

2000-02-01

Human error has been implicated in 70 to 80% of all civil and military aviation accidents. Yet, most accident reporting systems are not designed around any theoretical framework of human error. As a result, most accident databases are not conducive t...

Analysis of occupational accidents: prevention through the use of additional technical safety measures for machinery.

PubMed

Dźwiarek, Marek; Latała, Agata

2016-01-01

This article presents an analysis of results of 1035 serious and 341 minor accidents recorded by Poland's National Labour Inspectorate (PIP) in 2005-2011, in view of their prevention by means of additional safety measures applied by machinery users. Since the analysis aimed at formulating principles for the application of technical safety measures, the analysed accidents should bear additional attributes: the type of machine operation, technical safety measures and the type of events causing injuries. The analysis proved that the executed tasks and injury-causing events were closely connected and there was a relation between casualty events and technical safety measures. In the case of tasks consisting of manual feeding and collecting materials, the injuries usually occur because of the rotating motion of tools or crushing due to a closing motion. Numerous accidents also happened in the course of supporting actions, like removing pollutants, correcting material position, cleaning, etc.

Analysis of occupational accidents: prevention through the use of additional technical safety measures for machinery

PubMed Central

Dźwiarek, Marek; Latała, Agata

2016-01-01

This article presents an analysis of results of 1035 serious and 341 minor accidents recorded by Poland's National Labour Inspectorate (PIP) in 2005–2011, in view of their prevention by means of additional safety measures applied by machinery users. Since the analysis aimed at formulating principles for the application of technical safety measures, the analysed accidents should bear additional attributes: the type of machine operation, technical safety measures and the type of events causing injuries. The analysis proved that the executed tasks and injury-causing events were closely connected and there was a relation between casualty events and technical safety measures. In the case of tasks consisting of manual feeding and collecting materials, the injuries usually occur because of the rotating motion of tools or crushing due to a closing motion. Numerous accidents also happened in the course of supporting actions, like removing pollutants, correcting material position, cleaning, etc. PMID:26652689

Spatial study of mortality in motorcycle accidents in the State of Pernambuco, Northeastern Brazil.

PubMed

Silva, Paul Hindenburg Nobre de Vasconcelos; Lima, Maria Luiza Carvalho de; Moreira, Rafael da Silveira; Souza, Wayner Vieira de; Cabral, Amanda Priscila de Santana

2011-04-01

To analyze the spatial distribution of mortality due to motorcycle accidents in the state of Pernambuco, Northeastern Brazil. A population-based ecological study using data on mortality in motorcycle accidents from 01/01/2000 to 31/12/2005. The analysis units were the municipalities. For the spatial distribution analysis, an average mortality rate was calculated, using deaths from motorcycle accidents recorded in the Mortality Information System as the numerator, and as the denominator the population of the mid-period. Spatial analysis techniques, mortality smoothing coefficient estimate by the local empirical Bayesian method and Moran scatterplot, applied to the digital cartographic base of Pernambuco were used. The average mortality rate for motorcycle accidents in Pernambuco was 3.47 per 100 thousand inhabitants. Of the 185 municipalities, 16 were part of five clusters identified with average mortality rates ranging from 5.66 to 11.66 per 100 thousand inhabitants, and were considered critical areas. Three clusters are located in the area known as sertão and two in the agreste of the state. The risk of dying from a motorcycle accident is greater in conglomerate areas outside the metropolitan axis, and intervention measures should consider the economic, social and cultural contexts.

Analyzing the causation of a railway accident based on a complex network

NASA Astrophysics Data System (ADS)

Ma, Xin; Li, Ke-Ping; Luo, Zi-Yan; Zhou, Jin

2014-02-01

In this paper, a new model is constructed for the causation analysis of railway accident based on the complex network theory. In the model, the nodes are defined as various manifest or latent accident causal factors. By employing the complex network theory, especially its statistical indicators, the railway accident as well as its key causations can be analyzed from the overall perspective. As a case, the “7.23” China—Yongwen railway accident is illustrated based on this model. The results show that the inspection of signals and the checking of line conditions before trains run played an important role in this railway accident. In conclusion, the constructed model gives a theoretical clue for railway accident prediction and, hence, greatly reduces the occurrence of railway accidents.

Road accidents caused by sleepy drivers: Update of a Norwegian survey.

PubMed

Phillips, Ross Owen; Sagberg, Fridulv

2013-01-01

The current study tests, updates and expands a model of factors associated with sleepy driving, originally based on a 1997 survey of accident-involved Norwegian drivers (Sagberg, F., 1999. Road accidents caused by drivers falling asleep. Accident Analysis & Prevention 31, 639-649). The aim is to establish a robust model to inform measures to tackle sleepy driving. The original questions on (i) tiredness-related accidents and (ii) incidents of sleep behind the wheel in the last 12 months were again posed in 2003 and 2008, in independent surveys of Norwegian drivers involved in accidents reported to a large insurance company. According to those drivers at-fault for the accident, tiredness or sleepiness behind the wheel contributed to between 1.9 and 3.9 per cent of all types of accident reported to the insurance company across these years. Accident-involved drivers not at fault for the accident reported a reduction in the incidence of sleep behind the wheel for the preceding year, decreasing from 8.3 per cent in 1997 to 2.9 per cent in 2008. The reasons for this are not clear. According to logistic regression analysis of survey responses, the following factors were robustly associated with road accidents involving sleepy driving: driving off the road; good road conditions; longer distance driven since the start of the trip; and fewer years with a driving licence. The following factors are consistently associated with reports of sleep behind the wheel, whether or not it leads to an accident: being male; driving further per year; being younger; and having sleep-related health problems. Taken together these findings suggest that young, inexperienced male drivers who drive long distances may be a suitable target for road safety campaigns aimed at tackling sleepy driving. Copyright © 2012 Elsevier Ltd. All rights reserved.

Driving behaviors and on-duty road accidents: a French case-control study.

PubMed

Fort, Emmanuel; Chiron, Mireille; Davezies, Philippe; Bergeret, Alain; Charbotel, Barbara

2013-01-01

A case-control study was carried out to identify driving behaviors associated with the risk of on-duty road accident and to compare driving behaviors according to the type of journey (on duty, commuting, and private) for on-duty road accident victims. Cases were recruited from the Rhône Road Trauma Registry between January 2004 and October 2005 and were on duty at the time of the accident. Control subjects were recruited from the electoral rolls of the case subjects' constituencies of residence. Cases' and controls' driving behavior data were collected by self-administered questionnaire. A logistic regression was performed to identify behavioral risk factors for on-duty road accidents, taking into account age, sex, place of residence, road accident risk exposure, socio-occupational category, and type of road user. A second analysis focused specifically on the case subjects, comparing their self-assessed usual behaviors according to the type of journey. Significant factors for multivariate analysis of on-duty road accidents were female gender, history of on-duty road accidents during the previous 10 years, severe time pressure at work, and driving a vehicle not belonging to the driver. On-duty road accident victims reported behavioral risk factors more frequently in relation to driving for work than driving for private reasons or commuting: nonsystematic seat belt use, cell phone use at least once daily while driving, and history of accidents with injury during the previous 10 years. This study provides knowledge on behavioral risk factors for on-duty road accidents and differences in behavior according to the type of journey for subjects who have been on-duty road accident victims. These results will be useful for the design of on-duty road risk prevention.

[Human risk factors and injuries due to road accidents: analysis of current data].

PubMed

Marchetti, Pierpaolo; Morandi, Anna; Lombardo, Carlo; Gigli Berzolari, Francesca; Bruno, Vincenzo; Marinoni, Alessandra

2009-01-01

several studies have shown that most road accidents are due to human factors, and that these are strongly linked to a drive's age and sex. The aim of this study is to test the role that some human factors play in road accidents by analysing current road accident data in the Province of Pavia, in Northern Italy. road accidents that occurred in 2004 were analysed by integrating the paper database of the vehicle licensing office, properly computerised, with the 911 database of the Province of Pavia. This study has been carried out by analysing 1.347 road accidents and the associated 2.908 drivers of motorised vehicles. Northern Italy, the Province of Pavia. the death rate of drivers of 2-wheeled vehicles is almost nine times higher than that of 4-wheeled vehicles. Analysis shows that females are twice as exposed to road accidents than males; it also shows the benefits of extensive road education training and of being aged 30-64 and older. Drivers who have already been punished and have had their driving license scores reduced are likely to respond rapidly when in a dangerous situation and also to be without blame after an accident. Motorcycle riders are 25 times more likely to suffer serious injury than drivers of cars. Additionally, the risk of a woman being seriously injured is higher than for a man. females, young drivers and motorcycle riders who have not previously been penalised for a previous traffic violation have a higher risk of being seriously injured; females and motorcycle riders are also at greater risk of being seriously injured. We hope that this analysis will be used to improve preventative interventions for road accidents.r.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harmony, S.C.; Steiner, J.L.; Stumpf, H.J.

The PIUS advanced reactor is a 640-MWe pressurized water reactor developed by Asea Brown Boveri (ABB). A unique feature of the PIUS concept is the absence of mechanical control and shutdown rods. Reactivity is controlled by coolant boron concentration and the temperature of the moderator coolant. As part of the preapplication and eventual design certification process, advanced reactor applicants are required to submit neutronic and thermal-hydraulic safety analyses over a sufficient range of normal operation, transient conditions, and specified accident sequences. Los Alamos is supporting the US Nuclear Regulatory Commission`s preapplication review of the PIUS reactor. A fully one-dimensional modelmore » of the PIUS reactor has been developed for the Transient Reactor Analysis Code, TRACPF1/MOD2. Early in 1992, ABB submitted a Supplemental Information Package describing recent design modifications. An important feature of the PIUS Supplement design was the addition of an active scram system that will function for most transient and accident conditions. A one-dimensional Transient Reactor Analysis Code baseline calculation of the PIUS Supplement design were performed for a break in the main steam line at the outlet nozzle of the loop 3 steam generator. Sensitivity studies were performed to explore the robustness of the PIUS concept to severe off-normal conditions following a main steam line break. The sensitivity study results provide insights into the robustness of the design.« less

Epidemiology of Accidents in Tile Factories of Mangalore City in Karnataka

PubMed Central

Kumar, S Ganesh; Rathnakar, UP; Harsha Kumar, HN

2010-01-01

Background: Occupational accidents are a major point of concern in industries. The academic community should take the first step to address the long-neglected concerns of occupational safety. Objective: To assess the prevalence and pattern of occupational accidents. Materials and Methods: A record-based, cross-sectional study was done in three tile factories of Mangalore city, in Karnataka. A total of 416 workers were analyzed for the year 2004, and data regarding age, sex, job duration, type and nature of injury, body parts involved, and time of injury were collected in a prestructured proforma. Statistical Analysis: Proportions, Chi-square test, Univariate and Multivariate analysis. Results: The overall prevalence rate of accidents was found to be 18.5%. It was found that almost around 86% of the accidents had affected the limbs (upper limb 24.7%, lower limb 61%), around half (52%) of the injuries were contributed by superficial injuries, 40% of accidents were due to stepping/striking against objects and while handling. Hand tools and machinery in motion contributed to around 20% of the accidents. Accidents were more common among the younger age group and less-experienced workers. Multiple logistic regression analyses revealed that the age group of 30-39 years had an independent significant association with accidents (OR = 0.21, P = 0.04). Conclusion: Accidents in tile industries are an important occupational health problem in this area of the country. There is a need for proper safety training of the workers. PMID:20606926

Rontgen's Discovery of X Rays

ERIC Educational Resources Information Center

Thumm, Walter

1975-01-01

Relates the story of Wilhelm Conrad Rontgen and presents one view of the extent to which the discovery of the x-ray was an accident. Reconstructs the sequence of events that led to the discovery and includes photographs of the lab where he worked and replicas of apparatus used. (GS)

Squeal Those Tires! Automobile-Accident Reconstruction.

ERIC Educational Resources Information Center

Caples, Linda Griffin

1992-01-01

Methods use to reconstruct traffic accidents provide settings for real life applications for students in precalculus, mathematical analysis, or trigonometry. Described is the investigation of an accident in conjunction with the local Highway Patrol Academy integrating physics, vector, and trigonometry. Class findings were compared with those of…

A novel framework for improvement of road accidents considering decision-making styles of drivers in a large metropolitan area.

PubMed

Azadeh, Ali; Zarrin, Mansour; Hamid, Mehdi

2016-02-01

Road accidents can be caused by different factors such as human factors. Quality of the decision-making process of drivers could have a considerable impact on preventing disasters. The main objective of this study is the analysis of factors affecting road accidents by considering the severity of accidents and decision-making styles of drivers. To this end, a novel framework is proposed based on data envelopment analysis (DEA) and statistical methods (SMs) to assess the factors affecting road accidents. In this study, for the first time, dominant decision-making styles of drivers with respect to severity of injuries are identified. To show the applicability of the proposed framework, this research employs actual data of more than 500 samples in Tehran, Iran. The empirical results indicate that the flexible decision style is the dominant style for both minor and severe levels of accident injuries. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Comparative analysis of the radionuclide composition in fallout after the Chernobyl and the Fukushima accidents].

PubMed

Kotenko, K V; Shinkarev, S M; Abramov, Iu V; Granovskaia, E O; Iatsenko, V N; Gavrilin, Iu I; Margulis, U Ia; Garetskaia, O S; Imanaka, T; Khoshi, M

2012-01-01

The nuclear accident occurred at Fukushima Dai-ichi Nuclear Power Plant (NPP) (March 11, 2011) similarly to the accident at the Chernobyl NPP (April 26, 1986) is related to the level 7 of the INES. It is of interest to make an analysis of the radionuclide composition of the fallout following the both accidents. The results of the spectrometric measurements were used in that comparative analysis. Two areas following the Chernobyl accident were considered: (1) the near zone of the fallout - the Belarusian part of the central spot extended up to 60 km around the Chernobyl NPS and (2) the far zone of the fallout--the "Gomel-Mogilev" spot centered 200 km to the north-northeast of the damaged reactor. In the case of Fukushima accident the near zone up to about 60 km considered. The comparative analysis has been done with respect to refractory radionuclides (95Zr, 95Nb, 141Ce, 144Ce), as well as to the intermediate and volatile radionuclides 103Ru, 106Ru, 131I, 134Cs, 137Cs, 140La, 140Ba and the results of such a comparison have been discussed. With respect to exposure to the public the most important radionuclides are 131I and 137Cs. For the both accidents the ratios of 131I/137Cs in the considered soil samples are in the similar ranges: (3-50) for the Chernobyl samples and (5-70) for the Fukushima samples. Similarly to the Chernobyl accident a clear tendency that the ratio of 131I/137Cs in the fallout decreases with the increase of the ground deposition density of 137Cs within the trace related to a radioactive cloud has been identified for the Fukushima accident. It looks like this is a universal tendency for the ratio of 131I/137Cs versus the 137Cs ground deposition density in the fallout along the trace of a radioactive cloud as a result of a heavy accident at the NPP with radionuclides releases into the environment. This tendency is important for an objective reconstruction of 131I fallout based on the results of 137Cs measurements of soil samples carried out at late dates after the Fukushima accident.

Bus incident reporting, tracking and analysis system

DOT National Transportation Integrated Search

2006-08-01

Many Florida transit systems do little formal analysis of all accidents on an aggregate basis. In many transit system accidents and incidents are not being tracked or analyzed to identify common trends from types of incidents, location, driver, bus r...

Road casualties in work-related and private contexts: Occupational medical impact: Results from the ESPARR cohort.

PubMed

Fort, E; Pélissier, C; Fanjas, A; Charnay, P; Charbotel, B; Bergeret, A; Fontana, L; Hours, M

2018-05-22

Road accidents may impact victims' physical and/or mental health and socio-occupational life, notably including return to work. To assess whether the occupational medical consequences sustained by subjects injured in road accidents occurring in a work-related context differ from those associated with private accidents. 778 adults who were in work or occupational training at the time of their accident were included. Two groups were distinguished: 354 (45.5%) injured in road accidents occurring in a work-related context (commuting or on duty) and 424 (54.5%) injured in a private accident. The groups were compared on medical and occupational factors assessed on prospective follow-up at 6 months and 1 and 3 years. Multivariate analysis explored for factors associated at 6 months and 1 year with sick leave following the accident and duration of sick leave. There were no significant differences between groups for demographic data apart from a slightly higher injury severity in private accidents (32.5% of private accidents with MAIS3+(Maximum Abbreviated Injury Scale greater or equal to 3) vs. 23.7% for work-related accidents, p = 0.007). Victims of work-related accidents were more often on sick leave (OR = 1.8; 95% CI, 1.1-2.9). Although the length of sick leave is higher for work-related accidents that for private accidents, multivariate analysis showed that the injury severity and the post-traumatic stress disorder (PTSD) are significant factors to explain the time to return to work. There were no significant differences according to occupational impact during follow-up, notably including sick-leave duration, number of victims returning to work within 3 years and number of victims out of work due to incapacity. In the ESPARR (follow-up study of a road-accident population in the Rhône administrative county: Etude de Suivi d'une Population d'Accidentés de la Route dans le Rhône) cohort, the fact that a road accident occurred in a work-related context did not affect the occupational consequences.

Aircraft accidents : method of analysis

NASA Technical Reports Server (NTRS)

1929-01-01

This report on a method of analysis of aircraft accidents has been prepared by a special committee on the nomenclature, subdivision, and classification of aircraft accidents organized by the National Advisory Committee for Aeronautics in response to a request dated February 18, 1928, from the Air Coordination Committee consisting of the Assistant Secretaries for Aeronautics in the Departments of War, Navy, and Commerce. The work was undertaken in recognition of the difficulty of drawing correct conclusions from efforts to analyze and compare reports of aircraft accidents prepared by different organizations using different classifications and definitions. The air coordination committee's request was made "in order that practices used may henceforth conform to a standard and be universally comparable." the purpose of the special committee therefore was to prepare a basis for the classification and comparison of aircraft accidents, both civil and military. (author)

[The characteristics of computer simulation of traffic accidents].

PubMed

Zou, Dong-Hua; Liu, Ning-Guo; Chen, Jian-Guo; Jin, Xian-Long; Zhang, Xiao-Yun; Zhang, Jian-Hua; Chen, Yi-Jiu

2008-12-01

To reconstruct the collision process of traffic accident and the injury mode of the victim by computer simulation technology in forensic assessment of traffic accident. Forty actual accidents were reconstructed by stimulation software and high performance computer based on analysis of the trace evidences at the scene, damage of the vehicles and injury of the victims, with 2 cases discussed in details. The reconstruction correlated very well in 28 cases, well in 9 cases, and suboptimal in 3 cases with the above parameters. Accurate reconstruction of the accident would be helpful for assessment of the injury mechanism of the victims. Reconstruction of the collision process of traffic accident and the injury mechanism of the victim by computer simulation is useful in traffic accident assessment.

Risk of road accident associated with the use of drugs: a systematic review and meta-analysis of evidence from epidemiological studies.

PubMed

Elvik, Rune

2013-11-01

This paper is a corrigendum to a previously published paper where errors were detected. The errors have been corrected in this paper. The paper is otherwise identical to the previously published paper. A systematic review and meta-analysis of studies that have assessed the risk of accident associated with the use of drugs when driving is presented. The meta-analysis included 66 studies containing a total of 264 estimates of the effects on accident risk of using illicit or prescribed drugs when driving. Summary estimates of the odds ratio of accident involvement are presented for amphetamines, analgesics, anti-asthmatics, anti-depressives, anti-histamines, benzodiazepines, cannabis, cocaine, opiates, penicillin and zopiclone (a sleeping pill). For most of the drugs, small or moderate increases in accident risk associated with the use of the drugs were found. Information about whether the drugs were actually used while driving and about the doses used was often imprecise. Most studies that have evaluated the presence of a dose-response relationship between the dose of drugs taken and the effects on accident risk confirm the existence of a dose-response relationship. Use of drugs while driving tends to have a larger effect on the risk of fatal and serious injury accidents than on the risk of less serious accidents (usually property-damage-only accidents). The quality of the studies that have assessed risk varied greatly. There was a tendency for the estimated effects of drug use on accident risk to be smaller in well-controlled studies than in poorly controlled studies. Evidence of publication bias was found for some drugs. The associations found cannot be interpreted as causal relationships, principally because most studies do not control very well for potentially confounding factors. Copyright © 2012 Elsevier Ltd. All rights reserved.

Primary school accident reporting in one education authority

PubMed Central

Latif, A; Williams, W; Sibert, J

2002-01-01

Background: Studies have shown a correlation between increased accident rates and levels of deprivation in the community. School accident reporting is one area where an association might be expected. Aims: To investigate differences in primary school accident rates in deprived and more affluent wards, in an area managed by one education authority. Methods: Statistical analysis of accident form returns for 100 primary schools in one education authority in Wales over a two year period, in conjunction with visits to over one third of school sites. Results: Accident report rates from schools in deprived wards were three times higher than those from schools in more affluent wards. School visits showed that this discrepancy was attributable primarily to differences in reporting procedures. One third of schools did not report accidents and approximately half did not keep records of minor accidents. Conclusions: The association between school accident report rates and deprivation in the community is complex. School accident data from local education authorities may be unreliable for most purposes of collection. PMID:11827900

Primary school accident reporting in one education authority.

PubMed

Latif, A H A; Williams, W R; Sibert, J

2002-02-01

Studies have shown a correlation between increased accident rates and levels of deprivation in the community. School accident reporting is one area where an association might be expected. To investigate differences in primary school accident rates in deprived and more affluent wards, in an area managed by one education authority. Statistical analysis of accident form returns for 100 primary schools in one education authority in Wales over a two year period, in conjunction with visits to over one third of school sites. Accident report rates from schools in deprived wards were three times higher than those from schools in more affluent wards. School visits showed that this discrepancy was attributable primarily to differences in reporting procedures. One third of schools did not report accidents and approximately half did not keep records of minor accidents. The association between school accident report rates and deprivation in the community is complex. School accident data from local education authorities may be unreliable for most purposes of collection.

Learning lessons from Natech accidents - the eNATECH accident database

NASA Astrophysics Data System (ADS)

Krausmann, Elisabeth; Girgin, Serkan

2016-04-01

When natural hazards impact industrial facilities that house or process hazardous materials, fires, explosions and toxic releases can occur. This type of accident is commonly referred to as Natech accident. In order to prevent the recurrence of accidents or to better mitigate their consequences, lessons-learned type studies using available accident data are usually carried out. Through post-accident analysis, conclusions can be drawn on the most common damage and failure modes and hazmat release paths, particularly vulnerable storage and process equipment, and the hazardous materials most commonly involved in these types of accidents. These analyses also lend themselves to identifying technical and organisational risk-reduction measures that require improvement or are missing. Industrial accident databases are commonly used for retrieving sets of Natech accident case histories for further analysis. These databases contain accident data from the open literature, government authorities or in-company sources. The quality of reported information is not uniform and exhibits different levels of detail and accuracy. This is due to the difficulty of finding qualified information sources, especially in situations where accident reporting by the industry or by authorities is not compulsory, e.g. when spill quantities are below the reporting threshold. Data collection has then to rely on voluntary record keeping often by non-experts. The level of detail is particularly non-uniform for Natech accident data depending on whether the consequences of the Natech event were major or minor, and whether comprehensive information was available for reporting. In addition to the reporting bias towards high-consequence events, industrial accident databases frequently lack information on the severity of the triggering natural hazard, as well as on failure modes that led to the hazmat release. This makes it difficult to reconstruct the dynamics of the accident and renders the development of equipment vulnerability models linking the natural-hazard severity to the observed damage almost impossible. As a consequence, the European Commission has set up the eNATECH database for the systematic collection of Natech accident data and near misses. The database exhibits the more sophisticated accident representation required to capture the characteristics of Natech events and is publicly accessible at http://enatech.jrc.ec.europa.eu. This presentation outlines the general lessons-learning process, introduces the eNATECH database and its specific structure, and discusses natural-hazard specific lessons learned and features common to Natech accidents triggered by different natural hazards.

Study of Benefits of Passenger Protective Breathing Equipment from Analysis of Past Accidents

DTIC Science & Technology

1988-03-01

Rodeos (Tenerife) El 27 De Marzo De 1977 2. ICAO Aircraft Accident Digest No. 23, No. 2 B-30 AIRCRAFT ACCIDENT SUMMARY Carrier - Continental Airways...than FPL. However, a I’)-second donning de -lay of PBE may have resulted in a net disbenefit. k~f ¶ ~ 17. Key Words 18. Distributiion Stotement...in C-133 Test Article 23 with Postcrash Fire Conditions 5 Accident Profiles for 3/5/67 Varig DC-8 24 6 Accident Profiles for 4/8/68 British Overseas

Tobit analysis of vehicle accident rates on interstate highways.

PubMed

Anastasopoulos, Panagiotis Ch; Tarko, Andrew P; Mannering, Fred L

2008-03-01

There has been an abundance of research that has used Poisson models and its variants (negative binomial and zero-inflated models) to improve our understanding of the factors that affect accident frequencies on roadway segments. This study explores the application of an alternate method, tobit regression, by viewing vehicle accident rates directly (instead of frequencies) as a continuous variable that is left-censored at zero. Using data from vehicle accidents on Indiana interstates, the estimation results show that many factors relating to pavement condition, roadway geometrics and traffic characteristics significantly affect vehicle accident rates.

Analysis of traffic crash data in Kentucky : 2002-2006.

DOT National Transportation Integrated Search

2007-09-01

This report includes an analysis of traffic accident data in Kentucky for the years of 2002 through 2006. A primary objective of this study was to determine average accident statistics for Kentucky highways. Average and critical numbers and rates of ...

Analysis of traffic crash data in Kentucky : 2003-2007.

DOT National Transportation Integrated Search

2008-08-01

This report includes an analysis of traffic accident data in Kentucky for the years of 2003 through 2007. A primary objective of this study was to determine average accident statistics for Kentucky highways. Average and critical numbers and rates of ...

A Look at Aircraft Accident Analysis in the Early Days: Do Early 20th Century Accident Investigation Techniques Have Any Lessons for Today?

NASA Technical Reports Server (NTRS)

Holloway, C. M.; Johnson, C. W.

2007-01-01

In the early years of powered flight, the National Advisory Committee on Aeronautics in the United States produced three reports describing a method of analysis of aircraft accidents. The first report was published in 1928; the second, which was a revision of the first, was published in 1930; and the third, which was a revision and update of the second, was published in 1936. This paper describes the contents of these reports, and compares the method of analysis proposed therein to the methods used today.

Analysis of National Major Work Safety Accidents in China, 2003–2012

PubMed Central

YE, Yunfeng; ZHANG, Siheng; RAO, Jiaming; WANG, Haiqing; LI, Yang; WANG, Shengyong; DONG, Xiaomei

2016-01-01

Background: This study provides a national profile of major work safety accidents in China, which cause more than 10 fatalities per accident, intended to provide scientific basis for prevention measures and strategies to reduce major work safety accidents and deaths. Methods: Data from 2003–2012 Census of major work safety accidents were collected from State Administration of Work Safety System (SAWS). Published literature and statistical yearbook were also included to implement information. We analyzed the frequency of accidents and deaths, trend, geographic distribution and injury types. Additionally, we discussed the severity and urgency of emergency rescue by types of accidents. Results: A total of 877 major work safety accidents were reported, resulting in 16,795 deaths and 9,183 injuries. The numbers of accidents and deaths, mortality rate and incidence of major accidents have declined in recent years. The mortality rate and incidence was 0.71 and 1.20 per 106 populations in 2012, respectively. Transportation and mining contributed to the highest number of major accidents and deaths. Major aviation and railway accidents caused more casualties per incident, while collapse, machinery, electrical shock accidents and tailing dam accidents were the most severe situation that resulted in bigger proportion of death. Conclusion: Ten years’ major work safety accident data indicate that the frequency of accidents and number of eaths was declined and several safety concerns persist in some segments. PMID:27057515

A study of carburetor/induction system icing in general aviation accidents

NASA Technical Reports Server (NTRS)

Obermayer, R. W.; Roe, W. T.

1975-01-01

An assessment of the frequency and severity of carburetor/induction icing in general-aviation accidents was performed. The available literature and accident data from the National Transportation Safety Board were collected. A computer analysis of the accident data was performed. Between 65 and 90 accidents each year involve carburetor/induction system icing as a probable cause/factor. Under conditions conducive to carburetor/induction icing, between 50 and 70 percent of engine malfunction/failure accidents (exclusive of those due to fuel exhaustion) are due to carburetor/induction system icing. Since the evidence of such icing may not remain long after an accident, it is probable that the frequency of occurrence of such accidents is underestimated; therefore, some extrapolation of the data was conducted. The problem of carburetor/induction system icing is particularly acute for pilots with less than 1000 hours of total flying time. The severity of such accidents is about the same as any accident resulting from a forced landing or precautionary landing. About 144 persons, on the average, are exposed to death and injury each year in accidents involving carburetor/induction icing as a probable cause/factor.

Secondary school accident reporting in one education authority.

PubMed

Williams, W R; Latif, A H A; Sibert, J

2002-01-01

Secondary schools appear to have very different accident rates when they are compared on the basis of accident report returns. The variation may be as a result of real differences in accident rates or different reporting procedures. This study investigates accident reporting from secondary schools and, in particular, the role of the school nurse. Accident form returns covering a 2-year period were collected for statistical analysis from 13 comprehensive schools in one local education authority in Wales. School sites were visited in the following school year to obtain information about accident records held on site and accident reporting procedures. The main factors determining the number of school accident reports submitted to the education authority relate to differences in recording and reporting procedures, such as the employment of a nurse and the policy of the head teacher/safety officer on submitting accident returns. Accident and emergency department referrals from similar schools may show significant differences in specific injuries and their causes. The level of school accident activity cannot be gauged from reports submitted to the education authority. Lack of incentives for collecting good accident data, in conjunction with the degree of complacency in the current system, suggest that future accident rates and reporting activity are unlikely to change.

Understanding transit accidents using the National Transit Database and the role of Transit Intelligent Vehicle Initiative Technology in reducing accidents

DOT National Transportation Integrated Search

2004-06-01

This report documents the results of bus accident data analysis using the 2002 National Transit Database (NTD) and discusses the potential of using advanced technology being studied and developed under the U.S. Department of Transportations (U.S. ...

Phase 2 : evaluation of the national crash experience : comparison of CARDfile national motor vehicle accident projections with projections from NASS

DOT National Transportation Integrated Search

1987-07-01

This report details the results of an analysis that compared the Crash Avoidance : Research Data Base (CARDfile) with the National Accident Sampling System (NASS). : CARDfile combines, in one data base, the police accident records for three years : (...

10 CFR 830.204 - Documented safety analysis.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

10 CFR 830.204 - Documented safety analysis.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

10 CFR 830.204 - Documented safety analysis.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

10 CFR 830.204 - Documented safety analysis.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

A Human Factors Analysis of USAF Remotely Piloted Aircraft Mishaps

DTIC Science & Technology

2013-06-01

conditions or unsafe acts, where their respective removal would prevent a chain reaction from propagating, thus preventing the accident . This model...Force Col. Anthony Tvaryanas stated that “If you 19 really wanted to make a dent in preventing RPA accidents , the DoD needs to look at how they do...REFERENCES Greenwood, M. & Woods, H.M. (1919). The incidence of industrial accidents upon individuals with special reference to multiple accidents . (British

Hazmat transport: a methodological framework for the risk analysis of marshalling yards.

PubMed

Cozzani, Valerio; Bonvicini, Sarah; Spadoni, Gigliola; Zanelli, Severino

2007-08-17

A methodological framework was outlined for the comprehensive risk assessment of marshalling yards in the context of quantified area risk analysis. Three accident typologies were considered for yards: (i) "in-transit-accident-induced" releases; (ii) "shunting-accident-induced" spills; and (iii) "non-accident-induced" leaks. A specific methodology was developed for the assessment of expected release frequencies and equivalent release diameters, based on the application of HazOp and Fault Tree techniques to reference schemes defined for the more common types of railcar vessels used for "hazmat" transportation. The approach was applied to the assessment of an extended case-study. The results evidenced that "non-accident-induced" leaks in marshalling yards represent an important contribution to the overall risk associated to these zones. Furthermore, the results confirmed the considerable role of these fixed installations to the overall risk associated to "hazmat" transportation.

Vulnerability assessment of chemical industry facilities in South Korea based on the chemical accident history

NASA Astrophysics Data System (ADS)

Heo, S.; Lee, W. K.; Jong-Ryeul, S.; Kim, M. I.

2016-12-01

The use of chemical compounds are keep increasing because of their use in manufacturing industry. Chemical accident is growing as the consequence of the chemical use increment. Devastating damages from chemical accidents are far enough to aware people's cautious about the risk of the chemical accident. In South Korea, Gumi Hydrofluoric acid leaking accident triggered the importance of risk management and emphasized the preventing the accident over the damage reducing process after the accident occurs. Gumi accident encouraged the government data base construction relate to the chemical accident. As the result of this effort Chemical Safety-Clearing-house (CSC) have started to record the chemical accident information and damages according to the Harmful Chemical Substance Control Act (HCSC). CSC provide details information about the chemical accidents from 2002 to present. The detail informations are including title of company, address, business type, accident dates, accident types, accident chemical compounds, human damages inside of the chemical industry facilities, human damage outside of the chemical industry facilities, financial damages inside of the chemical industry facilities, and financial damages outside of the chemical industry facilities, environmental damages and response to the chemical accident. Collected the chemical accident history of South Korea from 2002 to 2015 and provide the spatial information to the each accident records based on their address. With the spatial information, compute the data on ArcGIS for the spatial-temporal analysis. The spatial-temporal information of chemical accident is organized by the chemical accident types, damages, and damages on environment and conduct the spatial proximity with local community and environmental receptors. Find the chemical accident vulnerable area of South Korea from 2002 to 2015 and add the vulnerable area of total period to examine the historically vulnerable area from the chemical accident in South Korea.

Pattern extraction for high-risk accidents in the construction industry: a data-mining approach.

PubMed

Amiri, Mehran; Ardeshir, Abdollah; Fazel Zarandi, Mohammad Hossein; Soltanaghaei, Elahe

2016-09-01

Accidents involving falls and falling objects (group I) are highly frequent accidents in the construction industry. While being hit by a vehicle, electric shock, collapse in the excavation and fire or explosion accidents (group II) are much less frequent, they make up a considerable proportion of severe accidents. In this study, multiple-correspondence analysis, decision tree, ensembles of decision tree and association rules methods are employed to analyse a database of construction accidents throughout Iran between 2007 and 2011. The findings indicate that in group I, there is a significant correspondence among these variables: time of accident, place of accident, body part affected, final consequence of accident and lost workdays. Moreover, the frequency of accidents in the night shift is less than others, and the frequency of injury to the head, back, spine and limbs are more. In group II, the variables time of accident and body part affected are mostly related and the frequency of accidents among married and older workers is more than single and young workers. There was a higher frequency in the evening, night shifts and weekends. The results of this study are totally in line with the previous research.

Simulation of Hydrogen Distribution in Ignalina NPP ALS Compartments During BDBA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babilas, Egidijus; Urbonavicius, Egidijus; Rimkevicius, Sigitas

2006-07-01

Accident Localisation System (ALS) of Ignalina NPP is a 'pressure suppression' type confinement, which protects the population, employees and environment from the radiation hazards. According to the Safety Analysis Report for Ignalina NPP {approx}110 m{sup 3} of hydrogen is released to ALS compartments during the Maximum Design Basis Accident. However in case of beyond design basis accident, when the oxidation of zirconium starts, the amount of generated hydrogen could be significantly higher. If the volume concentration of hydrogen in the compartment reaches 4%, there is a possibility for a combustible mixture to appear. To prevent the possible hydrogen accumulation inmore » the ALS of the Ignalina NPP during an accident the H{sub 2} control system is installed. The results of the performed analysis derived the places of the possible H{sub 2} accumulation in the ALS compartments during the transient processes and assessed the mixture combustibility in these places for a beyond design basis accident scenario. Such analysis of H{sub 2} distribution in the ALS of Ignalina NPP in case of BDBA was not performed before. (authors)« less

Key Parameters for Operator Diagnosis of BWR Plant Condition during a Severe Accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clayton, Dwight A.; Poore, III, Willis P.

2015-01-01

The objective of this research is to examine the key information needed from nuclear power plant instrumentation to guide severe accident management and mitigation for boiling water reactor (BWR) designs (specifically, a BWR/4-Mark I), estimate environmental conditions that the instrumentation will experience during a severe accident, and identify potential gaps in existing instrumentation that may require further research and development. This report notes the key parameters that instrumentation needs to measure to help operators respond to severe accidents. A follow-up report will assess severe accident environmental conditions as estimated by severe accident simulation model analysis for a specific US BWR/4-Markmore » I plant for those instrumentation systems considered most important for accident management purposes.« less

Classification of circulation type sequences applied to snow avalanches over the eastern Pyrenees (Andorra and Catalonia)

NASA Astrophysics Data System (ADS)

Esteban, Pere; Beck, Christoph; Philipp, Andreas

2010-05-01

Using data associated with accidents or damages caused by snow avalanches over the eastern Pyrenees (Andorra and Catalonia) several atmospheric circulation type catalogues have been obtained. For this purpose, different circulation type classification methods based on Principal Component Analysis (T-mode and S-mode using the extreme scores) and on optimization procedures (Improved K-means and SANDRA) were applied . Considering the characteristics of the phenomena studied, not only single day circulation patterns were taken into account but also sequences of circulation types of varying length. Thus different classifications with different numbers of types and for different sequence lengths were obtained using the different classification methods. Simple between type variability, within type variability, and outlier detection procedures have been applied for selecting the best result concerning snow avalanches type classifications. Furthermore, days without occurrence of the hazards were also related to the avalanche centroids using pattern-correlations, facilitating the calculation of the anomalies between hazardous and no hazardous days, and also frequencies of occurrence of hazardous events for each circulation type. Finally, the catalogues statistically considered the best results are evaluated using the avalanche forecaster expert knowledge. Consistent explanation of snow avalanches occurrence by means of circulation sequences is obtained, but always considering results from classifications with different sequence length. This work has been developed in the framework of the COST Action 733 (Harmonisation and Applications of Weather Type Classifications for European regions).

Impact of traffic congestion on road accidents: a spatial analysis of the M25 motorway in England.

PubMed

Wang, Chao; Quddus, Mohammed A; Ison, Stephen G

2009-07-01

Traffic congestion and road accidents are two external costs of transport and the reduction of their impacts is often one of the primary objectives for transport policy makers. The relationship between traffic congestion and road accidents however is not apparent and less studied. It is speculated that there may be an inverse relationship between traffic congestion and road accidents, and as such this poses a potential dilemma for transport policy makers. This study aims to explore the impact of traffic congestion on the frequency of road accidents using a spatial analysis approach, while controlling for other relevant factors that may affect road accidents. The M25 London orbital motorway, divided into 70 segments, was chosen to conduct this study and relevant data on road accidents, traffic and road characteristics were collected. A robust technique has been developed to map M25 accidents onto its segments. Since existing studies have often used a proxy to measure the level of congestion, this study has employed a precise congestion measurement. A series of Poisson based non-spatial (such as Poisson-lognormal and Poisson-gamma) and spatial (Poisson-lognormal with conditional autoregressive priors) models have been used to account for the effects of both heterogeneity and spatial correlation. The results suggest that traffic congestion has little or no impact on the frequency of road accidents on the M25 motorway. All other relevant factors have provided results consistent with existing studies.

'It was a freak accident': an analysis of the labelling of injury events in the US press.

PubMed

Smith, Katherine C; Girasek, Deborah C; Baker, Susan P; Manganello, Jennifer A; Bowman, Stephen M; Samuels, Alicia; Gielen, Andrea C

2012-02-01

Given that the news media shape our understanding of health issues, a study was undertaken to examine the use by the US media of the expression 'freak accident' in relation to injury events. This analysis is intended to contribute to the ongoing consideration of lay conceptualisation of injuries as 'accidents'. LexisNexis Academic was used to search three purposively selected US news sources (Associated Press, New York Times and Philadelphia Inquirer) for the expression 'freak accident' over 5 years (2005-9). Textual analysis included both structured and open coding. Coding included measures for who used the expression within the story, the nature of the injury event and the injured person(s) being reported upon, incorporation of prevention information within the story and finally a phenomenological consideration of the uses and meanings of the expression within the story context. Results The search yielded a dataset of 250 human injury stories incorporating the term 'freak accident'. Injuries sustained by professional athletes dominated coverage (61%). Fewer than 10% of stories provided a clear and explicit injury prevention message. Stories in which journalists employed the expression 'freak accident' were less likely to include prevention information than stories in which the expression was used by people quoted in the story. Journalists who frame injury events as freak accidents may be an appropriate focus for advocacy efforts. Effective prevention messages should be developed and disseminated to accompany injury reporting in order to educate and protect the public.

STAMP-Based HRA Considering Causality Within a Sociotechnical System: A Case of Minuteman III Missile Accident.

PubMed

Rong, Hao; Tian, Jin

2015-05-01

The study contributes to human reliability analysis (HRA) by proposing a method that focuses more on human error causality within a sociotechnical system, illustrating its rationality and feasibility by using a case of the Minuteman (MM) III missile accident. Due to the complexity and dynamics within a sociotechnical system, previous analyses of accidents involving human and organizational factors clearly demonstrated that the methods using a sequential accident model are inadequate to analyze human error within a sociotechnical system. System-theoretic accident model and processes (STAMP) was used to develop a universal framework of human error causal analysis. To elaborate the causal relationships and demonstrate the dynamics of human error, system dynamics (SD) modeling was conducted based on the framework. A total of 41 contributing factors, categorized into four types of human error, were identified through the STAMP-based analysis. All factors are related to a broad view of sociotechnical systems, and more comprehensive than the causation presented in the accident investigation report issued officially. Recommendations regarding both technical and managerial improvement for a lower risk of the accident are proposed. The interests of an interdisciplinary approach provide complementary support between system safety and human factors. The integrated method based on STAMP and SD model contributes to HRA effectively. The proposed method will be beneficial to HRA, risk assessment, and control of the MM III operating process, as well as other sociotechnical systems. © 2014, Human Factors and Ergonomics Society.

Effective environmental factors on geographical distribution of traffic accidents on pedestrians, downtown of Tehran City.

PubMed

Moradi, Ali; Rahmani, Khaled; Kavousi, Amir; Eshghabadi, Farshid; Nematollahi, Shahrzad; Zainni, Slahedyn; Soori, Hamid

2018-02-20

The aim of this study was to geographically analyse the traffic casualties in pedestrians in downtown of Tehran City. Study population consisted of pedestrians who had traffic injury accidents from April 2014 to March 2015 in Tehran City. Data were extracted from the offices of traffic police and municipality. For analysis of environmental factors and site of accidents, Ordinary Least Square (OLS) regression models and Geographically Weighted Regression (GWR) were used. All pedestrian accidents including 514 accidents were assessed in this study in which the site of accidents included arterial streets in 370 (71.9%) cases, collector streets in 133 cases (25.2%) and highways in 11 cases (2.1%). Geographical units of traffic accidents in pedestrians had statistically significant relationship with the number of bus stations, number of crossroads and recreational areas. Neighbourhoods close to markets are considered as the most dangerous places for injury in traffic accidents.

The SAS4A/SASSYS-1 Safety Analysis Code System, Version 5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fanning, T. H.; Brunett, A. J.; Sumner, T.

The SAS4A/SASSYS-1 computer code is developed by Argonne National Laboratory for thermal, hydraulic, and neutronic analysis of power and flow transients in liquidmetal- cooled nuclear reactors (LMRs). SAS4A was developed to analyze severe core disruption accidents with coolant boiling and fuel melting and relocation, initiated by a very low probability coincidence of an accident precursor and failure of one or more safety systems. SASSYS-1, originally developed to address loss-of-decay-heat-removal accidents, has evolved into a tool for margin assessment in design basis accident (DBA) analysis and for consequence assessment in beyond-design-basis accident (BDBA) analysis. SAS4A contains detailed, mechanistic models of transientmore » thermal, hydraulic, neutronic, and mechanical phenomena to describe the response of the reactor core, its coolant, fuel elements, and structural members to accident conditions. The core channel models in SAS4A provide the capability to analyze the initial phase of core disruptive accidents, through coolant heat-up and boiling, fuel element failure, and fuel melting and relocation. Originally developed to analyze oxide fuel clad with stainless steel, the models in SAS4A have been extended and specialized to metallic fuel with advanced alloy cladding. SASSYS-1 provides the capability to perform a detailed thermal/hydraulic simulation of the primary and secondary sodium coolant circuits and the balance-ofplant steam/water circuit. These sodium and steam circuit models include component models for heat exchangers, pumps, valves, turbines, and condensers, and thermal/hydraulic models of pipes and plena. SASSYS-1 also contains a plant protection and control system modeling capability, which provides digital representations of reactor, pump, and valve controllers and their response to input signal changes.« less

GIS-based accident location and analysis system (GIS-ALAS) : project report : phase I

DOT National Transportation Integrated Search

1998-04-06

This report summarizes progress made in Phase I of the geographic information system (GIS) based Accident Location and Analysis System (GIS-ALAS). The GIS-ALAS project builds on PC-ALAS, a locationally-referenced highway crash database query system d...

[Environmental, social, and roadway vulnerability in accidents involving transportation of hazardous products: a case study of the BR-101 highway between Osório and Torres in Rio Grande do Sul State, Brazil].

PubMed

Tinoco, Maria Auxiliadora Cannarozzo; Nodari, Christine Tessele; Pereira, Kimberllyn Rosa da Silva

2016-09-19

This study aimed to assess the environmental and social vulnerability and identify critical highway stretches for accidents involving transportation of hazardous products on the BR-101 highway between the cities of Osório and Torres in Rio Grande do Sul State, Brazil. The study's approach consisted of a multiple-criteria analysis combining highway safety analysis and environmental and social vulnerability analysis in the occurrence of accidents with hazardous products, plus cartographic analysis techniques. Thirty-eight kilometers of the highway showed high vulnerability, of which 8 kilometers with critical vulnerability, associated with bridges over rivers, water uptake points, a tunnel, environmental preservation areas, and an urban area. These stretches should be prioritized when developing action plans for accident mitigation and development of public policies for this highway. This proved to be an unprecedented approach when compared to existing studies and a potentially useful tool for decision-making in emergency operations.

[Violence and accidents among older and younger adults: evidence from the Surveillance System for Violence and Accidents (VIVA), Brazil].

PubMed

Luz, Tatiana Chama Borges; Malta, Deborah Carvalho; Sá, Naíza Nayla Bandeira de; Silva, Marta Maria Alves da; Lima-Costa, Maria Fernanda

2011-11-01

Data from the Brazilian Surveillance System for Violence and Accidents (VIVA) in 2009 were used to examine socio-demographic characteristics, outcomes, and types of accidents and violence treated at 74 sentinel emergency services in 23 Brazilian State capitals and the Federal District. The analysis included 25,201 individuals aged > 20 years (10.1% > 60 years); 89.3% were victims of accidents and 11.9% victims of violence. Hospitalization was the outcome in 11.1% of cases. Compared to the general population, there were more men and non-white individuals among victims of accidents, and especially among victims of violence. As compared to younger adults (20-59 years), accidents and violence against elderly victims showed less association with alcohol, a higher proportion of domestic incidents, more falls and pedestrian accidents, and aggression by family members. Policies for the prevention of accidents and violence should consider the characteristics of these events in the older population.

[Determinant factors and conduct in post-accident with biological material among pre-hospital professionals].

PubMed

Paiva, Maria Henriqueta Rocha Siqueira; Oliveira, Adriana Cristina

2011-01-01

This transversal study was carried out with a multiprofessional team in the pre-hospital care in Minas Gerais, Brazil. It aimed to estimate the incidence of occupational accidents by exposure to biological material and post-accidents conductsta. Descriptive analysis and logistic regression were used. Incidence of accidents was 19.8%: 39,1% perforating-cutting materials and 56.5% body fluids. Doctors (33.3%) and drivers (24.0%) were most involved. Inadequate subsequent measures were highly prevalent: no medical assessment (69.6%), no work accident communication issued (91.3%), no measures (52.2%) and no serological follow-up (52.2%). Variables associated with accidents were: age >31 years old (OR = 3,02; IC95%: 1,25 - 7,33; p = 0,014) and working in basic support units (OR = 5,36; IC95%: 1,51 19,08; p = 0,010). The implementation of post-accidents protocols is suggested in order to reduce accidents and under-notification, and increase post-accident follow-up.

Analysis of Occupational Accident Fatalities and Injuries Among Male Group in Iran Between 2008 and 2012

PubMed Central

Alizadeh, Seyed Shamseddin; Mortazavi, Seyed Bagher; Sepehri, Mohammad Mehdi

2015-01-01

Background: Because of occupational accidents, permanent disabilities and deaths occur and economic and workday losses emerge. Objectives: The purpose of the present study was to investigate the factors responsible for occupational accidents occurred in Iran. Patients and Methods: The current study analyzed 1464 occupational accidents recorded by the Ministry of Labor and Social Affairs’ offices in Iran during 2008 - 2012. At first, general understanding of accidents was obtained using descriptive statistics. Afterwards, the chi-square test and Cramer’s V statistic (Vc) were used to determine the association between factors influencing the type of injury as occupational accident outcomes. Results: There was no significant association between marital status and time of day with the type of injury. However, activity sector, cause of accident, victim’s education, age of victim and victim’s experience were significantly associated with the type of injury. Conclusions: Successful accident prevention relies largely on knowledge about the causes of accidents. In any accident control activity, particularly in occupational accidents, correctly identifying high-risk groups and factors influencing accidents is the key to successful interventions. Results of this study can cause to increase accident awareness and enable workplace’s management to select and prioritize problem areas and safety system weakness in workplaces. PMID:26568848

Review of U.S. Army Unmanned Aerial Systems Accident Reports: Analysis of Human Error Contributions

DTIC Science & Technology

2018-03-20

USAARL Report No. 2018-08 Review of U.S. Army Unmanned Aerial Systems Accident Reports: Analysis of Human Error Contributions By Kathryn A...3 Statistical Analysis Approach ..............................................................................................3 Results...1 Introduction The success of unmanned aerial systems (UAS) operations relies upon a variety of factors, including, but not limited to

[The medical organizational aspects of decreasing of preventable mortality in the case of traffic accident in municipal district].

PubMed

Voloshina, L V; Plutnitskiĭ, A N

2010-01-01

The article deals with the results of the study of such actual issue as decreasing of preventable mortality in the case of traffic accident in municipal district. The analysis was based on the mortality statistical data and the expertise of causes of lethal outcomes of traffic accidents. The results are used to develop the measures of improving the organization and quality of medical care of victims of road accident on the pre-hospital and hospital stages on the level of municipal health care to decrease the human losses caused by traffic accident.

The analysis of influence of individual and environmental factors on 2-wheeled users' injuries.

PubMed

Marković, Nenad; Pešić, Dalibor R; Antić, Boris; Vujanić, Milan

2016-08-17

Powered 2-wheeled motor vehicles (PTWs) are one of the most vulnerable categories of road users. Bearing that fact in mind, we have researched the effects of individual and environmental factors on the severity and type of injuries of PTW users. The aim was to recognize the circumstances that cause these accidents and take some preventive actions that would improve the level of road safety for PTWs. In the period from 2001 to 2010, an analysis of 139 road accidents involving PTWs was made by the Faculty of Transport and Traffic Engineering in Belgrade. The effects of both individual (age, gender, etc.) and environmental factors (place of an accident, time of day, etc.) on the cause of accidents and severity and type of injuries of PTWs are reported in this article. Analyses of these effects were conducted using logistic regression, chi-square tests, and Pearson's correlation. Factors such as categories of road users, pavement conditions, place of accident, age, and time of day have a statistically significant effect on PTW injuries, whereas other factors (gender, road type; that is, straight or curvy) do not. The article also defines the interdependence of the occurrence of particular injuries at certain speeds. The results show that if PTW users died of a head injury, these were usually concurrent with chest injuries, injuries to internal organs, and limb injuries. It has been shown that there is a high degree of influence of individual factors on the occurrence of accidents involving 2-wheelers (PTWs/bicycles) but with no statistically significant relation. Establishing the existence of such conditionalities enables identifying and defining factors that have an impact on the occurrence of traffic accidents involving bicyclists or PTWs. Such a link between individual factors and the occurrence of accidents makes it possible for system managers to take appropriate actions aimed at certain categories of 2-wheelers in order to reduce casualties in a particular area. The analysis showed that most of the road factors do not have a statistically significant effect on either category of 2-wheeler. Namely, the logistic regression analysis showed that there is a statistically significant effect of the place of accident on the occurrence of accidents involving bicyclists.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Panayotov, Dobromir; Poitevin, Yves; Grief, Andrew

'Fusion for Energy' (F4E) is designing, developing, and implementing the European Helium-Cooled Lead-Lithium (HCLL) and Helium-Cooled Pebble-Bed (HCPB) Test Blanket Systems (TBSs) for ITER (Nuclear Facility INB-174). Safety demonstration is an essential element for the integration of these TBSs into ITER and accident analysis is one of its critical components. A systematic approach to accident analysis has been developed under the F4E contract on TBS safety analyses. F4E technical requirements, together with Amec Foster Wheeler and INL efforts, have resulted in a comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials,more » and phenomena while remaining consistent with the approach already applied to ITER accident analyses. Furthermore, the methodology phases are illustrated in the paper by its application to the EU HCLL TBS using both MELCOR and RELAP5 codes.« less

A-WINGS: an integrated genome database for Pleurocybella porrigens (Angel's wing oyster mushroom, Sugihiratake).

PubMed

Yamamoto, Naoki; Suzuki, Tomohiro; Kobayashi, Masaaki; Dohra, Hideo; Sasaki, Yohei; Hirai, Hirofumi; Yokoyama, Koji; Kawagishi, Hirokazu; Yano, Kentaro

2014-12-03

The angel's wing oyster mushroom (Pleurocybella porrigens, Sugihiratake) is a well-known delicacy. However, its potential risk in acute encephalopathy was recently revealed by a food poisoning incident. To disclose the genes underlying the accident and provide mechanistic insight, we seek to develop an information infrastructure containing omics data. In our previous work, we sequenced the genome and transcriptome using next-generation sequencing techniques. The next step in achieving our goal is to develop a web database to facilitate the efficient mining of large-scale omics data and identification of genes specifically expressed in the mushroom. This paper introduces a web database A-WINGS (http://bioinf.mind.meiji.ac.jp/a-wings/) that provides integrated genomic and transcriptomic information for the angel's wing oyster mushroom. The database contains structure and functional annotations of transcripts and gene expressions. Functional annotations contain information on homologous sequences from NCBI nr and UniProt, Gene Ontology, and KEGG Orthology. Digital gene expression profiles were derived from RNA sequencing (RNA-seq) analysis in the fruiting bodies and mycelia. The omics information stored in the database is freely accessible through interactive and graphical interfaces by search functions that include 'GO TREE VIEW' browsing, keyword searches, and BLAST searches. The A-WINGS database will accelerate omics studies on specific aspects of the angel's wing oyster mushroom and the family Tricholomataceae.

A Human Factors Analysis and Classification System (HFACS) Examination of Commercial Vessel Accidents

DTIC Science & Technology

2012-09-01

Naval Operations before the Congress on FY2013 Department of Navy posture. Heinrich , H . W. (1941). Industrial accident prevention : A scientific...Theory The core of the Domino Theory, developed by Herbert W. Heinrich who studied industrial safety in the early 1900s, is that accidents are a result...chain of events resulting in an accident . Heinrich likened the dominos to unsafe conditions or unsafe acts, where their subsequent removal prevents a

[Analysis of accidents in selected occupations in the Szczecin shipyard S.A. in the years 1989-93].

PubMed

Kośmider, K; Niezgoda, A; Dadej, R; Myślak, M

1997-01-01

In a five-year follow-up study (1989-93), 1317 work-related accidents and their relation to occupational exposure among male workers employed at the Szczecin Shipyard were analysed. The highest rates of accidents were found among welders, fitters, electrical mechanics and platers. The role of the age, duration of employment, type of the job performed and its contribution to the rate and pattern of accidents, were also investigated.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattison, M.B.; Blackman, H.S.; Novack, S.D.

The Office for Analysis and Evaluation of Operational Data (AEOD) has sought the assistance of the Idaho National Engineering Laboratory (INEL) to make some significant enhancements to the SAPHIRE-based Accident Sequence Precursor (ASP) models recently developed by the INEL. The challenge of this project is to provide the features of a full-scale PRA within the framework of the simplified ASP models. Some of these features include: (1) uncertainty analysis addressing the standard PRA uncertainties and the uncertainties unique to the ASP models and methods, (2) incorporation and proper quantification of individual human actions and the interaction among human actions, (3)more » enhanced treatment of common cause failures, and (4) extension of the ASP models to more closely mimic full-scale PRAs (inclusion of more initiators, explicitly modeling support system failures, etc.). This paper provides an overview of the methods being used to make the above improvements.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattison, M.B.; Blackman, H.S.; Novack, S.D.

The Office for Analysis and Evaluation of Operational Data (AEOD) has sought the assistance of the Idaho National Engineering Laboratory (INEL) to make some significant enhancements to the SAPHIRE-based Accident Sequence Precursor (ASP) models recently developed by the INEL. The challenge of this project is to provide the features of a full-scale PRA within the framework of the simplified ASP models. Some of these features include: (1) uncertainty analysis addressing the standard PRA uncertainties and the uncertainties unique to the ASP models and methodology, (2) incorporation and proper quantification of individual human actions and the interaction among human actions, (3)more » enhanced treatment of common cause failures, and (4) extension of the ASP models to more closely mimic full-scale PRAs (inclusion of more initiators, explicitly modeling support system failures, etc.). This paper provides an overview of the methods being used to make the above improvements.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grabaskas, David; Bucknor, Matthew; Jerden, James

A mechanistic source term (MST) calculation attempts to realistically assess the transport and release of radionuclides from a reactor system to the environment during a specific accident sequence. The U.S. Nuclear Regulatory Commission (NRC) has repeatedly stated its expectation that advanced reactor vendors will utilize an MST during the U.S. reactor licensing process. As part of a project to examine possible impediments to sodium fast reactor (SFR) licensing in the U.S., an analysis was conducted regarding the current capabilities to perform an MST for a metal fuel SFR. The purpose of the project was to identify and prioritize any gapsmore » in current computational tools, and the associated database, for the accurate assessment of an MST. The results of the study demonstrate that an SFR MST is possible with current tools and data, but several gaps exist that may lead to possibly unacceptable levels of uncertainty, depending on the goals of the MST analysis.« less

Analysis for the Progressive Failure Response of Textile Composite Fuselage Frames

NASA Technical Reports Server (NTRS)

Johnson, Eric R.; Boitnott, Richard L. (Technical Monitor)

2002-01-01

A part of aviation accident mitigation is a crash worthy airframe structure, and an important measure of merit for a crash worthy structure is the amount of kinetic energy that can be absorbed in the crush of the structure. Prediction of the energy absorbed from finite element analyses requires modeling the progressive failure sequence. Progressive failure modes may include material degradation, fracture and crack growth, and buckling and collapse. The design of crash worthy airframe components will benefit from progressive failure analyses that have been validated by tests. The subject of this research is the development of a progressive failure analysis for textile composite. circumferential fuselage frames subjected to a quasi-static, crash-type load. The test data for these frames are reported, and these data, along with stub column test data, are to be used to develop and to validate methods for the progressive failure response.

ATWS analysis for Browns Ferry Nuclear Plant Unit 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dallman, R.J.; Jouse, W.C.

1985-01-01

Analyses of postulated Anticipated Transients Without Scram (ATWS) were performed at the Idaho National Engineering Laboratory (INEL). The Browns Ferry Nuclear Plant Unit 1 (BFNP1) was selected as the subject of this work because of the cooperation of the Tennessee Valley Authority (TVA). The work is part of the Severe Accident Sequence Analysis (SASA) Program of the US Nuclear Regulatory Commission (NRC). A Main Steamline Isolation Valve (MSIV) closure served as the transient initiator for these analyses, which proceeded a complete failure to scram. Results from the analyses indicate that operator mitigative actions are required to prevent overpressurization of themore » primary containment. Uncertainties remain concerning the effectiveness of key mitigative actions. The effectiveness of level control as a power reduction procedure is limited. Power level resulting from level control only reduce the Pressure Suppression Pool (PSP) heatup rate from 6 to 4F/min.« less

Economic situation and occupational accidents in Poland: 2002-2014 panel data regional study.

PubMed

Łyszczarz, Błażej; Nojszewska, Ewelina

2018-01-07

Occupational accidents constitute a substantial health and economic burden for societies around the world and a variety of factors determine the frequency of accidents at work. The aim of this paper is to investigate the relationship between the economic situation and the rate of occupational accidents in Poland. The analysis comprised data for 66 Polish sub-regions taken from the Central Statistical Office's Local Data Bank. The regression analysis with panel data for period 2002-2014 was applied to identify the relationships involved. Four measures of accidents were used: the rates of total occupational accidents, accidents among men and women separately as well as days of incapacity to work due to accidents at work per employee. Four alternative measures assessed the economic situation: gross domestic product (GDP) per capita, average remuneration, the unemployment rate and number of dwelling permits. The confounding variables included were: employment in hazardous conditions and the size of enterprises. The results of the regression estimates show that the number of occupational accidents in Poland exhibits procyclical behavior, which means that more accidents are observed during the times of economic expansion. Stronger relationships were observed in the equations explaining men's accident rates as well as total rates. A weaker and not always statistically significant impact of economic situation was identified for women's accident rates and days of incapacity to work. The results have important implications for occupational health and safety actions. In the periods of higher work intensity employers should focus on appropriate training and supervision of inexperienced workers as well as on ensuring enough time for already experienced employees to recuperate. In terms of public health actions, policy makers should focus on scrutinizing working conditions, educating employers and counteracting possible discrimination of injured employees. Int J Occup Med Environ Health 2018;31(2):151-164. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Factors associated with non-return to work in the severely injured victims 3 years after a road accident: A prospective study.

PubMed

Pélissier, C; Fort, E; Fontana, L; Charbotel, B; Hours, M

2017-09-01

Road accidents may impact victims' physical and/or mental health and socio-occupational life, particularly the capacity to return to work. The purpose of our study is to assess modifiable medical and socio-occupational factors of non-return to work in the severely injured 3 years after a road accident. Among1,168 road accidents casualties in the Rhône administrative Département of France followed for five years, 141 of the 222 severely injured (Maximal Abbreviated Injury Scale ≥ 3) aged more than 16 years who were in work at the time of the accident, reported whether they had returned to work in the 3 years following the accident. The subgroups of those who had (n=113) and had not returned to work (n=28) were compared for socio-occupational (gender, age, educational level, marital status, socio-occupational group) accident-related medical factors (type of road user, type of journey, responsibility in the accident, initial care) and post-accident medical factors (pain intensity, post-traumatic stress disorder, physical sequelae, quality of life) by using standardized tools. Severity of initial head, face and lower-limb injury, intense persistent pain, post-traumatic stress disorder, poor self-assessed quality of life and health status at 3 years were associated with non-return to work on univariate analysis. On multivariate analysis, severity of initial head and lower-limb injury, intense persistent pain at 3 years and post-traumatic stress disorder were significantly associated with non-return to work 3 years following severe road-accident injury. Post-traumatic stress disorder and chronic pain were essential modifiable medical determinants of non-return to work in the severely injured after a road accident: early adapted management could promote return to work in the severely injured. Improve early adapted treatment of pain and PTSD in the rehabilitation team should help the severely injured return to work following a road accident. Copyright © 2017 Elsevier Ltd. All rights reserved.

Station blackout calculations for Browns Ferry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ott, L.J.; Weber, C.F.; Hyman, C.R.

1985-01-01

This paper presents the results of calculations performed with the ORNL SASA code suite for the Station Blackout Severe Accident Sequence at Browns Ferry. The accident is initiated by a loss of offsite power combined with failure of all onsite emergency diesel generators to start and load. The Station Blackout is assumed to persist beyond the point of battery exhaustion (at six hours) and without DC power, cooling water could no longer be injected into the reactor vessel. Calculations are continued through the period of core degradation and melting, reactor vessel failure, and the subsequent containment failure. An estimate ofmore » the magnitude and timing of the concomitant fission product releases is also provided.« less

Spectral Analysis of the Effects of Daylight Saving Time on Motor Vehicle Fatal Traffic Accidents

DOT National Transportation Integrated Search

1977-04-01

This report shows that Daylight Saving Time (DST) reduces the number of persons killed in motor vehicle fatal traffic accidents by about one percent. This estimate is based on a spectral (Fourier) analysis of these fatalities which utilizes a filteri...

Quality evaluation of official accident reports conducted by Labour Authorities in Andalusia (Spain).

PubMed

Salguero-Caparros, Francisco; Suarez-Cebador, Manuel; Carrillo-Castrillo, Jesús A; Rubio-Romero, Juan Carlos

2018-01-01

A public accident investigation is carried out when the consequences of the incident are significant or the accident has occurred in unusual circumstances. We evaluated the quality of the official accident investigations being conducted by Safety Specialists of the Labour Authorities in Andalusia. To achieve this objective, we analysed 98 occupational accident investigations conducted by the Labour Authorities in Andalusia in the last quarter of 2014. Various phases in the accident investigation process were examined, such as the use of the Eurostat variables within European Statistics on Accidents at Work (ESAW), detection of causes, determination of preventive measures, cost analysis of the accidents, identification of noncompliance with legal requirements or the investigation method used. The results of this study show that 77% of the official occupational accident investigation reports analysed were conducted in accordance with all the quality criteria recommended in the literature. To enhance glogal learning, and optimize allocation of resources, we propose the development of a harmonized European model for the public investigation of occupational accidents. Further it would be advisable to create a common classification and coding system for the causes of accidents for all European Union Member States.

Accident data study of concrete construction companies' similarities and differences between qualified and non-qualified workers in Spain.

PubMed

López-Arquillos, Antonio; Rubio-Romero, Juan Carlos; Gibb, Alistair

2015-01-01

The aim of this paper is to discuss findings from an analysis of accidents in concrete construction companies in Spain and to compare the accident rates of qualified and non-qualified workers. A total of 125,021 accidents between 2003 and 2008 involving both blue-collar and white-collar workers were analysed, comparing the variables of occupation, age, company staff, length of service, location of the accident, together with the severity of the accidents. Results showed that lack of experience in the first month is more significant in non-qualified workers and experienced supervisors and that head injuries are more likely to lead to fatalities. The most remarkable similarity was that fatal accidents to and from the worksite are a problem common to both groups of workers.

How life changes itself: the Read-Write (RW) genome.

PubMed

Shapiro, James A

2013-09-01

The genome has traditionally been treated as a Read-Only Memory (ROM) subject to change by copying errors and accidents. In this review, I propose that we need to change that perspective and understand the genome as an intricately formatted Read-Write (RW) data storage system constantly subject to cellular modifications and inscriptions. Cells operate under changing conditions and are continually modifying themselves by genome inscriptions. These inscriptions occur over three distinct time-scales (cell reproduction, multicellular development and evolutionary change) and involve a variety of different processes at each time scale (forming nucleoprotein complexes, epigenetic formatting and changes in DNA sequence structure). Research dating back to the 1930s has shown that genetic change is the result of cell-mediated processes, not simply accidents or damage to the DNA. This cell-active view of genome change applies to all scales of DNA sequence variation, from point mutations to large-scale genome rearrangements and whole genome duplications (WGDs). This conceptual change to active cell inscriptions controlling RW genome functions has profound implications for all areas of the life sciences. © 2013 Elsevier B.V. All rights reserved.

The Fukushima Daiichi Accident Study Information Portal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shawn St. Germain; Curtis Smith; David Schwieder

This paper presents a description of The Fukushima Daiichi Accident Study Information Portal. The Information Portal was created by the Idaho National Laboratory as part of joint NRC and DOE project to assess the severe accident modeling capability of the MELCOR analysis code. The Fukushima Daiichi Accident Study Information Portal was created to collect, store, retrieve and validate information and data for use in reconstructing the Fukushima Daiichi accident. In addition to supporting the MELCOR simulations, the Portal will be the main DOE repository for all data, studies and reports related to the accident at the Fukushima Daiichi nuclear powermore » station. The data is stored in a secured (password protected and encrypted) repository that is searchable and accessible to researchers at diverse locations.« less

[Factors associated with work-related accidents in the informal commercial sector].

PubMed

Rios, Marcela Andrade; Nery, Adriana Alves; Rios, Polianna Alves Andrade; Casotti, Cezar Augusto; Cardoso, Jefferson Paixão

2015-06-01

This study aimed to estimate the incidence of non-fatal work-related accidents in the informal commercial sector and analyze associated socio-demographic, occupational, workplace, and health factors, in a cross-sectional survey of 434 workers in the business district of Jequié, Bahia State, Brazil, in 2013. Logistic regression was used to assess factors associated with accidents. Incidence of accidents in the previous 12 months was estimated at 32.3%, and multivariate analysis showed higher odds of accidents in male sex workers (OR = 1.61), young individuals (OR = 4.62), meat or poultry workers (OR = 9.55), and workers performing heavy physical work (OR = 1.71). The results show the need for public policies to prevent accidents in the informal commercial sector.

Are schools safer for children than public places?

PubMed Central

Maitra, A K; Sweeney, G

1996-01-01

OBJECTIVE--To investigate the frequency and severity of accidents to children in schools. METHODS--Retrospective analysis of accidents occurring in school over a six month period and resulting in attendance at an accident and emergency department. Comparison was made with accidents occurring in public places, RESULTS--During the study period there were 127 school and 251 public place accidents causing fractures or dislocations requiring hospital treatment in 3-16 year old children; 22.4% (127/567) of all injuries at school resulted in fractures or dislocations, as opposed to 20.8% (251/1197) of those sustained in public places. CONCLUSIONS--Injuries at school are a cause for concern as they occur in a supervised environment and this should be the target of accident prevention measures. PMID:8733659

Risk Analysis of a Fuel Storage Terminal Using HAZOP and FTA

PubMed Central

Baixauli-Pérez, Mª Piedad

2017-01-01

The size and complexity of industrial chemical plants, together with the nature of the products handled, means that an analysis and control of the risks involved is required. This paper presents a methodology for risk analysis in chemical and allied industries that is based on a combination of HAZard and OPerability analysis (HAZOP) and a quantitative analysis of the most relevant risks through the development of fault trees, fault tree analysis (FTA). Results from FTA allow prioritizing the preventive and corrective measures to minimize the probability of failure. An analysis of a case study is performed; it consists in the terminal for unloading chemical and petroleum products, and the fuel storage facilities of two companies, in the port of Valencia (Spain). HAZOP analysis shows that loading and unloading areas are the most sensitive areas of the plant and where the most significant danger is a fuel spill. FTA analysis indicates that the most likely event is a fuel spill in tank truck loading area. A sensitivity analysis from the FTA results show the importance of the human factor in all sequences of the possible accidents, so it should be mandatory to improve the training of the staff of the plants. PMID:28665325

Risk Analysis of a Fuel Storage Terminal Using HAZOP and FTA.

PubMed

Fuentes-Bargues, José Luis; González-Cruz, Mª Carmen; González-Gaya, Cristina; Baixauli-Pérez, Mª Piedad

2017-06-30

The size and complexity of industrial chemical plants, together with the nature of the products handled, means that an analysis and control of the risks involved is required. This paper presents a methodology for risk analysis in chemical and allied industries that is based on a combination of HAZard and OPerability analysis (HAZOP) and a quantitative analysis of the most relevant risks through the development of fault trees, fault tree analysis (FTA). Results from FTA allow prioritizing the preventive and corrective measures to minimize the probability of failure. An analysis of a case study is performed; it consists in the terminal for unloading chemical and petroleum products, and the fuel storage facilities of two companies, in the port of Valencia (Spain). HAZOP analysis shows that loading and unloading areas are the most sensitive areas of the plant and where the most significant danger is a fuel spill. FTA analysis indicates that the most likely event is a fuel spill in tank truck loading area. A sensitivity analysis from the FTA results show the importance of the human factor in all sequences of the possible accidents, so it should be mandatory to improve the training of the staff of the plants.

Canister Storage Building (CSB) Hazard Analysis Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

POWERS, T.B.

2000-03-16

This report describes the methodology used in conducting the Canister Storage Building (CSB) Hazard Analysis to support the final CSB Safety Analysis Report and documents the results. This report describes the methodology used in conducting the Canister Storage Building (CSB) hazard analysis to support the CSB final safety analysis report (FSAR) and documents the results. The hazard analysis process identified hazardous conditions and material-at-risk, determined causes for potential accidents, identified preventive and mitigative features, and qualitatively estimated the frequencies and consequences of specific occurrences. The hazard analysis was performed by a team of cognizant CSB operations and design personnel, safetymore » analysts familiar with the CSB, and technical experts in specialty areas. The material included in this report documents the final state of a nearly two-year long process. Attachment A provides two lists of hazard analysis team members and describes the background and experience of each. The first list is a complete list of the hazard analysis team members that have been involved over the two-year long process. The second list is a subset of the first list and consists of those hazard analysis team members that reviewed and agreed to the final hazard analysis documentation. The material included in this report documents the final state of a nearly two-year long process involving formal facilitated group sessions and independent hazard and accident analysis work. The hazard analysis process led to the selection of candidate accidents for further quantitative analysis. New information relative to the hazards, discovered during the accident analysis, was incorporated into the hazard analysis data in order to compile a complete profile of facility hazards. Through this process, the results of the hazard and accident analyses led directly to the identification of safety structures, systems, and components, technical safety requirements, and other controls required to protect the public, workers, and environment.« less

Assessment and prediction of road accident injuries trend using time-series models in Kurdistan.

PubMed

Parvareh, Maryam; Karimi, Asrin; Rezaei, Satar; Woldemichael, Abraha; Nili, Sairan; Nouri, Bijan; Nasab, Nader Esmail

2018-01-01

Road traffic accidents are commonly encountered incidents that can cause high-intensity injuries to the victims and have direct impacts on the members of the society. Iran has one of the highest incident rates of road traffic accidents. The objective of this study was to model the patterns of road traffic accidents leading to injury in Kurdistan province, Iran. A time-series analysis was conducted to characterize and predict the frequency of road traffic accidents that lead to injury in Kurdistan province. The injuries were categorized into three separate groups which were related to the car occupants, motorcyclists and pedestrian road traffic accident injuries. The Box-Jenkins time-series analysis was used to model the injury observations applying autoregressive integrated moving average (ARIMA) and seasonal autoregressive integrated moving average (SARIMA) from March 2009 to February 2015 and to predict the accidents up to 24 months later (February 2017). The analysis was carried out using R-3.4.2 statistical software package. A total of 5199 pedestrians, 9015 motorcyclists, and 28,906 car occupants' accidents were observed. The mean (SD) number of car occupant, motorcyclist and pedestrian accident injuries observed were 401.01 (SD 32.78), 123.70 (SD 30.18) and 71.19 (SD 17.92) per year, respectively. The best models for the pattern of car occupant, motorcyclist, and pedestrian injuries were the ARIMA (1, 0, 0), SARIMA (1, 0, 2) (1, 0, 0) 12 , and SARIMA (1, 1, 1) (0, 0, 1) 12 , respectively. The motorcyclist and pedestrian injuries showed a seasonal pattern and the peak was during summer (August). The minimum frequency for the motorcyclist and pedestrian injuries were observed during the late autumn and early winter (December and January). Our findings revealed that the observed motorcyclist and pedestrian injuries had a seasonal pattern that was explained by air temperature changes overtime. These findings call the need for close monitoring of the accidents during the high-risk periods in order to control and decrease the rate of the injuries.

78 FR 60321 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses and Combined Licenses...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-01

... sample selection. A steam generator tube rupture (SGTR) event is one of the design basis accidents that... in the design basis accident analysis. The proposed change will not cause the consequences of a SGTR... changes to the plant design basis or postulated accidents resulting from potential tube degradation. The...

Scaling and design analyses of a scaled-down, high-temperature test facility for experimental investigation of the initial stages of a VHTR air-ingress accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arcilesi, David J.; Ham, Tae Kyu; Kim, In Hun

2015-07-01

A critical event in the safety analysis of the very high-temperature gas-cooled reactor (VHTR) is an air-ingress accident. This accident is initiated, in its worst case scenario, by a double-ended guillotine break of the coaxial cross vessel, which leads to a rapid reactor vessel depressurization. In a VHTR, the reactor vessel is located within a reactor cavity that is filled with air during normal operating conditions. Following the vessel depressurization, the dominant mode of ingress of an air–helium mixture into the reactor vessel will either be molecular diffusion or density-driven stratified flow. The mode of ingress is hypothesized to dependmore » largely on the break conditions of the cross vessel. Since the time scales of these two ingress phenomena differ by orders of magnitude, it is imperative to understand under which conditions each of these mechanisms will dominate in the air ingress process. Computer models have been developed to analyze this type of accident scenario. There are, however, limited experimental data available to understand the phenomenology of the air-ingress accident and to validate these models. Therefore, there is a need to design and construct a scaled-down experimental test facility to simulate the air-ingress accident scenarios and to collect experimental data. The current paper focuses on the analyses performed for the design and operation of a 1/8th geometric scale (by height and diameter), high-temperature test facility. A geometric scaling analysis for the VHTR, a time scale analysis of the air-ingress phenomenon, a transient depressurization analysis of the reactor vessel, a hydraulic similarity analysis of the test facility, a heat transfer characterization of the hot plenum, a power scaling analysis for the reactor system, and a design analysis of the containment vessel are discussed.« less

The Analysis of the Contribution of Human Factors to the In-Flight Loss of Control Accidents

NASA Technical Reports Server (NTRS)

Ancel, Ersin; Shih, Ann T.

2012-01-01

In-flight loss of control (LOC) is currently the leading cause of fatal accidents based on various commercial aircraft accident statistics. As the Next Generation Air Transportation System (NextGen) emerges, new contributing factors leading to LOC are anticipated. The NASA Aviation Safety Program (AvSP), along with other aviation agencies and communities are actively developing safety products to mitigate the LOC risk. This paper discusses the approach used to construct a generic integrated LOC accident framework (LOCAF) model based on a detailed review of LOC accidents over the past two decades. The LOCAF model is comprised of causal factors from the domain of human factors, aircraft system component failures, and atmospheric environment. The multiple interdependent causal factors are expressed in an Object-Oriented Bayesian belief network. In addition to predicting the likelihood of LOC accident occurrence, the system-level integrated LOCAF model is able to evaluate the impact of new safety technology products developed in AvSP. This provides valuable information to decision makers in strategizing NASA's aviation safety technology portfolio. The focus of this paper is on the analysis of human causal factors in the model, including the contributions from flight crew and maintenance workers. The Human Factors Analysis and Classification System (HFACS) taxonomy was used to develop human related causal factors. The preliminary results from the baseline LOCAF model are also presented.

An aftermath analysis of the 2014 coal mine accident in Soma, Turkey: Use of risk performance indicators based on historical experience.

PubMed

Spada, Matteo; Burgherr, Peter

2016-02-01

On the 13th of May 2014 a fire related incident in the Soma coal mine in Turkey caused 301 fatalities and more than 80 injuries. This has been the largest coal mine accident in Turkey, and in the OECD country group, so far. This study investigated if such a disastrous event should be expected, in a statistical sense, based on historical observations. For this purpose, PSI's ENSAD database is used to extract accident data for the period 1970-2014. Four different cases are analyzed, i.e., OECD, OECD w/o Turkey, Turkey and USA. Analysis of temporal trends for annual numbers of accidents and fatalities indicated a non-significant decreasing tendency for OECD and OECD w/o Turkey and a significant one for USA, whereas for Turkey both measures showed an increase over time. The expectation analysis revealed clearly that an event with the consequences of the Soma accident is rather unlikely for OECD, OECD w/o Turkey and USA. In contrast, such a severe accident has a substantially higher expectation for Turkey, i.e. it cannot be considered an extremely rare event, based on historical experience. This indicates a need for improved safety measures and stricter regulations in the Turkish coal mining sector in order to get closer to the rest of OECD. Copyright © 2015 Elsevier Ltd. All rights reserved.

Pressing the Approach: A NASA Study of 19 Recent Accidents Yields a New Perspective on Pilot Error

NASA Technical Reports Server (NTRS)

Berman, Benjamin A.; Dismukes, R. Key

2007-01-01

This article begins with a review of two sample airplane accidents that were caused by pilot error. The analysis of these and 17 other accidents suggested that almost all experienced pilot operating in the same environment in which the accident crews were operating and knowing only what the accident crews knew at each moment of the flight, would be vulnerable to making a similar decision and similar errors. Whether a particular crew in a given situation makes errors depends on somewhat random interaction of factors. Two themes that seem to be prevalent in these cases are: Plan Continuation Bias, and Snowballing Workload.

Strategies for dealing with resistance to recommendations from accident investigations.

PubMed

Lundberg, Jonas; Rollenhagen, Carl; Hollnagel, Erik; Rankin, Amy

2012-03-01

Accident investigation reports usually lead to a set of recommendations for change. These recommendations are, however, sometimes resisted for reasons such as various aspects of ethics and power. When accident investigators are aware of this, they use several strategies to overcome the resistance. This paper describes strategies for dealing with four different types of resistance to change. The strategies were derived from qualitative analysis of 25 interviews with Swedish accident investigators from seven application domains. The main contribution of the paper is a better understanding of effective strategies for achieving change associated with accident investigation. Copyright © 2011 Elsevier Ltd. All rights reserved.

Learning from Trending, Precursor Analysis, and System Failures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Youngblood, R. W.; Duffey, R. B.

2015-11-01

Models of reliability growth relate current system unreliability to currently accumulated experience. But “experience” comes in different forms. Looking back after a major accident, one is sometimes able to identify previous events or measurable performance trends that were, in some sense, signaling the potential for that major accident: potential that could have been recognized and acted upon, but was not recognized until the accident occurred. This could be a previously unrecognized cause of accidents, or underestimation of the likelihood that a recognized potential cause would actually operate. Despite improvements in the state of practice of modeling of risk and reliability,more » operational experience still has a great deal to teach us, and work has been going on in several industries to try to do a better job of learning from experience before major accidents occur. It is not enough to say that we should review operating experience; there is too much “experience” for such general advice to be considered practical. The paper discusses the following: 1. The challenge of deciding what to focus on in analysis of operating experience. 2. Comparing what different models of learning and reliability growth imply about trending and precursor analysis.« less

Decision-problem state analysis methodology

NASA Technical Reports Server (NTRS)

Dieterly, D. L.

1980-01-01

A methodology for analyzing a decision-problem state is presented. The methodology is based on the analysis of an incident in terms of the set of decision-problem conditions encountered. By decomposing the events that preceded an unwanted outcome, such as an accident, into the set of decision-problem conditions that were resolved, a more comprehensive understanding is possible. All human-error accidents are not caused by faulty decision-problem resolutions, but it appears to be one of the major areas of accidents cited in the literature. A three-phase methodology is presented which accommodates a wide spectrum of events. It allows for a systems content analysis of the available data to establish: (1) the resolutions made, (2) alternatives not considered, (3) resolutions missed, and (4) possible conditions not considered. The product is a map of the decision-problem conditions that were encountered as well as a projected, assumed set of conditions that should have been considered. The application of this methodology introduces a systematic approach to decomposing the events that transpired prior to the accident. The initial emphasis is on decision and problem resolution. The technique allows for a standardized method of accident into a scenario which may used for review or the development of a training simulation.

Spatio-temporal patterns of hazards and their use in risk assessment and mitigation. Case study of road accidents in Romania

NASA Astrophysics Data System (ADS)

Catalin Stanga, Iulian

2013-04-01

Road accidents are among the leading causes of death in many world countries, partly as an inherent consequence of the increasing mobility of today society. The World Health Organization estimates that 1.3 million people died in road accidents in 2011, which means 186 deaths per million. The tragic picture is completed by millions of peoples experiencing different physical injuries or by the enormous social and economic costs that these events imply. Romania has one of the most unsafe road networks within the European Union, with annual averages of 9400 accidents, 8300 injuries and almost 2680 fatalities (2007-2012). An average of 141 death per million is more than twice the average fatality rate in European Union (about 60 death per million). Other specific indicators (accidents or fatalities reported to the road length, vehicle fleet size, driving license owners or adult population etc.) are even worst in the same European context. Road accidents are caused by a complex series of factors, some of them being a relatively constant premise, while others act as catalyzing factors or triggering agent: road features and quality, vehicle technical state, weather conditions, human related factors etc. All these lead to a complex equation with too many unknown variables, making almost impossible a probabilistic approach. However, the high concentration of accidents in a region or in some road sectors is caused by the existence of a specific context, created by factors with permanent or repetitive character, and leads to the idea of a spatial autocorrelation between locations of different adjoining accident. In the same way, the increasing frequency of road accidents and of their causes repeatability in different periods of the year would allow to identify those black timeframes with higher incidence of road accidents. Identifying and analyzing the road blackspots (hotspots) and black zones would help to improve road safety by acting against the common causes that create the spatial or temporal clustering of crash accidents. Since the 1990's, Geographical Informational Systems (GIS) became a very important tool for traffic and road safety management, allowing not only the spatial and multifactorial analysis, but also graphical and non-graphical outputs. The current paper presents an accessible GIS methodology to study the spatio-temporal pattern of injury related road accidents, to identify the high density accidents zones, to make a cluster analysis, to create multicriterial typologies, to identify spatial and temporal similarities and to explain them. In this purpose, a Geographical Information System was created, allowing a complex analysis that involves not only the events, but also a large set of interrelated and spatially linked attributes. The GIS includes the accidents as georeferenced point elements with a spatially linked attribute database: identification information (date, location details); accident type; main, secondary and aggravating causes; data about driver; vehicle information; consequences (damages, injured peoples and fatalities). Each attribute has its own number code that allows both the statistical analysis and the spatial interrogation. The database includes those road accidents that led to physical injuries and loss of human lives between 2007 and 2012 and the spatial analysis was realized using TNTmips 7.3 software facilities. Data aggregation and processing allowed creating the spatial pattern of injury related road accidents through Kernel density estimation at three different levels (national - Romania; county level - Iasi County; local level - Iasi town). Spider graphs were used to create the temporal pattern or road accidents at three levels (daily, weekly and monthly) directly related to their causes. Moreover the spatial and temporal database relates the natural hazards (glazed frost, fog, and blizzard) with the human made ones, giving the opportunity to evaluate the nature of uncertainties in risk assessment. At the end, this paper provides a clustering methodology based on several environmental indicators intended to classify the spatial and temporal hotspots of road traffic insecurity. The results are a useful guide for planners and decision makers in developing effective road safety strategies and measures.

How safe are HEMS-programmes in Germany? A retrospective analysis.

PubMed

Thies, Karl-Christian; Sep, Daan; Derksen, Remon

2006-03-01

Recent accidents with helicopter emergency medical service (HEMS) aircraft raise the question how safe HEMS in Germany is and how accidents could be prevented. We surveyed all German HEMS-programmes and reviewed the data of the German Aviation Authority regarding accidents with HEMS. An average German HEMS-programme encounters one accident leading to at least severe damage or loss of the helicopter in 26 operating years, one accident resulting in casualties in 65 operating years and one fatal accident in 111 operating years. The major causes of accidents were obstacle strikes during landing at the scene. Flying in bad weather conditions and lack of discipline were other factors contributing to HEMS-accidents. HEMS-safety could be improved by special training programmes for pilots and HEMS-crewmembers to address the factors listed above. Safety training for doctors is recommended but we did not find support for the notion of changing the doctor's legal position of a passenger to a HEMS-crewmember.

Occupational accidents aboard merchant ships

PubMed Central

Hansen, H; Nielsen, D; Frydenberg, M

2002-01-01

Objectives: To investigate the frequency, circumstances, and causes of occupational accidents aboard merchant ships in international trade, and to identify risk factors for the occurrence of occupational accidents as well as dangerous working situations where possible preventive measures may be initiated. Methods: The study is a historical follow up on occupational accidents among crew aboard Danish merchant ships in the period 1993–7. Data were extracted from the Danish Maritime Authority and insurance data. Exact data on time at risk were available. Results: A total of 1993 accidents were identified during a total of 31 140 years at sea. Among these, 209 accidents resulted in permanent disability of 5% or more, and 27 were fatal. The mean risk of having an occupational accident was 6.4/100 years at sea and the risk of an accident causing a permanent disability of 5% or more was 0.67/100 years aboard. Relative risks for notified accidents and accidents causing permanent disability of 5% or more were calculated in a multivariate analysis including ship type, occupation, age, time on board, change of ship since last employment period, and nationality. Foreigners had a considerably lower recorded rate of accidents than Danish citizens. Age was a major risk factor for accidents causing permanent disability. Change of ship and the first period aboard a particular ship were identified as risk factors. Walking from one place to another aboard the ship caused serious accidents. The most serious accidents happened on deck. Conclusions: It was possible to clearly identify work situations and specific risk factors for accidents aboard merchant ships. Most accidents happened while performing daily routine duties. Preventive measures should focus on workplace instructions for all important functions aboard and also on the prevention of accidents caused by walking around aboard the ship. PMID:11850550

Safety regulations, firm size, and the risk of accidents in E&P operations on the Gulf of Mexico outer continental shelf

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iledare, O.O.; Pulsipher, A.G.; Baumann, R.H.

1996-12-31

The current expanded role of smaller independent oil producers in the OCS has led to concern about the possibility of increased risk of accidents in E&P operations on the Gulf of Mexico OCS. In addition, questions have been posed concerning the effects of the Minerals Management Service`s (MMS) safety regulations and inspection program, firm size, and industry practices on the risk of accidents in E&P operations on the Gulf of Mexico OCS. The specific purposes of the study reported in this paper were to ascertain (1) whether any empirical justification exists for the widespread concern that an increase in independentsmore » relative share of E&P operations in the Gulf OCS region will be detrimental to safety, and (2) whether MMS policies and safety programs have reduced the frequency or severity of accidents on the OCS. Our statistical and descriptive analyses of data on accidents from MMS provide no statistical evidence to support the apprehension that an expanded role for independents in E&P activity constitutes any major threat to safety on the OCS. Further, the results of our econometrics analysis confirm the expectation that the more effective MMS inspectors are at detecting incidents of noncompliance the lower the rate of accidents on the OCS is, ceteris paribus. In addition the results indicate that the variability in platform exposure years--cumulative age of operating platform--in comparison to other factors explains a significant portion of the variation in accidents per operating platform. That is, the platform aging process provides more opportunity for accidents than any other contributing factors. Our econometrics analysis also suggests that, if the other factors contributing to offshore accidents are held constant, the responsiveness of accident rate to drilling activity is inelastic while the response of accident rate to production activity levels is elastic.« less

Analysis of traffic accidents in Romania, 2009.

PubMed

Călinoiu, Geovana; Minca, Dana Galieta; Furtunescu, Florentina Ligia

2012-01-01

This paper aimed to underline the main consequences of traffic accidents in Romania 2009 and their associated causes or circumstances. We identified some problematic geographic areas, some critical months or moments of the day and also the most frequent causes; all these should become targets for the future planning. The current analysis provides some priority criteria for public health interventions. So, the future national road safety strategy should be in line with the EU objectives, but also with the national priorities. Romania is far away from the average EU target for 2010 of halving the death by traffic accidents registered in 2001. To describe the circumstances and the consequences related to traffic accidents registered in Romania, for the year 2009. An ecological study was conducted. The traffic accidents circumstances were analyzed in terms of magnitude, geographic space, time and cause. The consequences were analyzed as affected people and damaged cars. A total of 28,627 traffic accidents were registered in Romania during the year 2009. 2,796 people were killed and 27,968 were hospitalized and 42,443 cars were damaged. 3 of 4 accidents were caused by violations on behalf of the car drivers. Most common violations in car drivers were excess of speed and priority violations (52.4%). Among the pedestrians, 7 of 10 accidents were caused by illegal crossing. A higher number of accidents occurred during the summer months and during the evening hours (from 5.00 pm till 8.00 pm). The traffic accidents represent a real public health problem in Romania and a serious burden for the health system. The gap between Romania and the other EU member states needs to be diminished in the next decade. In this purpose, the future national road safety strategy should be in line with the EU objectives, but also with the national priorities. Research is needed to understand the causes and the socio-economical impact of traffic accidents and to define appropriate national objectives.

Causes of Coal Mine Accidents in the World and Turkey.

PubMed

Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

2015-04-01

Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents.

Causes of Coal Mine Accidents in the World and Turkey

PubMed Central

Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

2015-01-01

Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents. PMID:29404108

The special severity of occupational accidents in the afternoon: "the lunch effect".

PubMed

Camino López, Miguel A; Fontaneda, Ignacio; González Alcántara, Oscar J; Ritzel, Dale O

2011-05-01

The severity of occupational accidents suffered by construction workers at different hours of the day is analyzed in this study. It may be seen that the interval of time between 13:00 and 17:00 has incomprehensibly high rates of severe and fatal accidents in comparison with any other. We associate this higher accident rate with what we have termed the "lunch effect". We studied 10,239,303 labor accidents in Spain over the period 1990-2002. The relationships between potential risk factors for occupational accidents around lunch in Spain, especially alcohol consumption are studied, using two methods: analysis of national archival data of 2,155,954 occupational accidents suffered by workers in the construction sector over the period 1990-2002 and a survey study. This study also seeks to contribute the opinions of the workers themselves regarding the causes that might explain this situation. Copyright © 2010 Elsevier Ltd. All rights reserved.

Predictions of structural integrity of steam generator tubes under normal operating, accident, an severe accident conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Majumdar, S.

1997-02-01

Available models for predicting failure of flawed and unflawed steam generator tubes under normal operating, accident, and severe accident conditions are reviewed. Tests conducted in the past, though limited, tended to show that the earlier flow-stress model for part-through-wall axial cracks overestimated the damaging influence of deep cracks. This observation was confirmed by further tests at high temperatures, as well as by finite-element analysis. A modified correlation for deep cracks can correct this shortcoming of the model. Recent tests have shown that lateral restraint can significantly increase the failure pressure of tubes with unsymmetrical circumferential cracks. This observation was confirmedmore » by finite-element analysis. The rate-independent flow stress models that are successful at low temperatures cannot predict the rate-sensitive failure behavior of steam generator tubes at high temperatures. Therefore, a creep rupture model for predicting failure was developed and validated by tests under various temperature and pressure loadings that can occur during postulated severe accidents.« less

Causes of accidents in terrain parks: an exploratory factor analysis of recreational freestylers' views.

PubMed

Carús, Luis

2014-03-01

This study examines ski and snowboard terrain park users' views on aspects associated with accidents by identifying and assessing variables that may influence the occurrence of accidents and the resulting injuries. The research was conducted in a major resort in the Spanish Pyrenees, using information gathered from freestyle skiers and snowboarders aged 6 or older. To identify interrelationships among variables and to group the variables belonging to unified concepts, an exploratory factor analysis was performed using varimax rotation. The results revealed 5 factors that grouped the measured variables that may influence the occurrence of accidents while freestyling in terrain parks. The park features, conditions of the activity, and the user's personal conditions were found to have the most substantial influence on the freestylers' perceptions. Variables identified as components of the main factors of accident risk in terrain parks should be incorporated into resort management communication and policies. © 2013 Wilderness Medical Society Published by Wilderness Medical Society All rights reserved.

Differences in Characteristics of Aviation Accidents During 1993-2012 Based on Aircraft Type

NASA Technical Reports Server (NTRS)

Evans, Joni K.

2015-01-01

Civilian aircraft are available in a variety of sizes, engine types, construction materials and instrumentation complexity. For the analysis reported here, eleven aircraft categories were developed based mostly on aircraft size and engine type, and these categories were applied to twenty consecutive years of civil aviation accidents. Differences in various factors were examined among these aircraft types, including accident severity, pilot characteristics and accident occurrence categories. In general, regional jets and very light sport aircraft had the lowest rates of adverse outcomes (injuries, fatal accidents, aircraft destruction, major accidents), while aircraft with twin (piston) engines or with a single (piston) engine and retractable landing gear carried the highest incidence of adverse outcomes. The accident categories of abnormal runway contact, runway excursions and non-powerplant system/component failures occur frequently within all but two or three aircraft types. In contrast, ground collisions, loss of control - on ground/water and powerplant system/component failure occur frequently within only one or two aircraft types. Although accidents in larger aircraft tend to have less severe outcomes, adverse outcome rates also differ among accident categories. It may be that the type of accident has as much or more influence on the outcome as the type of aircraft.

The situation of hazardous chemical accidents in China between 2000 and 2006.

PubMed

Duan, Weili; Chen, Guohua; Ye, Qing; Chen, Qingguang

2011-02-28

From the aspects of the total quantity of accidents, regional inequality, enterprises scale and environmental pollution accidents, this study makes an analysis of hazardous chemical accidents in China for the period spanning from 2000 to 2006. The following results are obtained: firstly, there were lots of accidents and fatalities in hazardous chemical business, i.e., the number of casualty accidents fluctuated between 200 and 600/year, the number of fatality fluctuated between 220 and 1100/year. Secondly, the accident rate in developed southeast coastal areas, e.g., Guangdong, Zhejiang and Jiangsu, was far higher than that in the northwest regions, e.g., Xizang, Xinjiang, and Qinghai. Thirdly, nearly 80% of dangerous chemical accidents had occurred in small and medium-sized enterprises (SMEs). Finally, various sudden environmental pollution accidents resulted from hazardous chemicals were frequent in recent years, causing a huge damage to human and property. Then, based on the readjustment of economic structure in the last decades, the development status of Occupational Health and Safety (OHS) in SMEs and other factors, the paper explores the main causes, which offers valuable insight into measures that should be taken to reduce hazardous chemical accidents. Copyright © 2010 Elsevier B.V. All rights reserved.

Estimation of fatality and injury risk by means of in-depth fatal accident investigation data.

PubMed

Yannis, George; Papadimitriou, Eleonora; Dupont, Emmanuelle; Martensen, Heike

2010-10-01

In this article the factors affecting fatality and injury risk of road users involved in fatal accidents are analyzed by means of in-depth accident investigation data, with emphasis on parameters not extensively explored in previous research. A fatal accident investigation (FAI) database is used, which includes intermediate-level in-depth data for a harmonized representative sample of 1300 fatal accidents in 7 European countries. The FAI database offers improved potential for analysis, because it includes information on a number of variables that are seldom available, complete, or accurately recorded in road accident databases. However, the fact that only fatal accidents are examined requires for methodological adjustments, namely, the correction for two types of effects on a road user's baseline risk: "accident size" effects, and "relative vulnerability" effects. Fatality and injury risk can be then modeled through multilevel logistic regression models, which account for the hierarchical dependences of the road accident process. The results show that the baseline fatality risk of road users involved in fatal accidents decreases with accident size and increases with the vulnerability of the road user. On the contrary, accident size increases nonfatal injury risk of road users involved in fatal accidents. Other significant effects on fatality and injury risk in fatal accidents include road user age, vehicle type, speed limit, the chain of accident events, vehicle maneuver, and safety equipment. In particular, the presence and use of safety equipment such as seat belt, antilock braking system (ABS), and electronic stability program (ESP) are protection factors for car occupants, especially for those seated at the front seats. Although ABS and ESP systems are typically associated with positive effects on accident occurrence, the results of this research revealed significant related effects on accident severity as well. Moreover, accident consequences are more severe when the most harmful event of the accident occurs later within the accident chain.

Requirements Analysis for the Army Safety Management Information System (ASMIS)

DTIC Science & Technology

1989-03-01

8217_>’ Telephone Number « .. PNL-6819 Limited Distribution Requirements Analysis for the Army Safety Management Information System (ASMIS) Final...PNL-6819 REQUIREMENTS ANALYSIS FOR THE ARMY SAFETY MANAGEMENT INFORMATION SYSTEM (ASMIS) FINAL REPORT J. S. Littlefield A. L. Corrigan March...accidents. This accident data is available under the Army Safety Management Information System (ASMIS) which is an umbrella for many databases

Methodological guidelines for developing accident modification functions.

PubMed

Elvik, Rune

2015-07-01

This paper proposes methodological guidelines for developing accident modification functions. An accident modification function is a mathematical function describing systematic variation in the effects of road safety measures. The paper describes ten guidelines. An example is given of how to use the guidelines. The importance of exploratory analysis and an iterative approach in developing accident modification functions is stressed. The example shows that strict compliance with all the guidelines may be difficult, but represents a level of stringency that should be strived for. Currently the main limitations in developing accident modification functions are the small number of good evaluation studies and the often huge variation in estimates of effect. It is therefore still not possible to develop accident modification functions for very many road safety measures. Copyright © 2015 Elsevier Ltd. All rights reserved.

Driver Performance Problems of Intercity Bus Public Transportation Safety in Indonesia

NASA Astrophysics Data System (ADS)

Suraji, A.; Harnen, S.; Wicaksono, A.; Djakfar, L.

2017-11-01

The risk of an inter-city bus public accident can be influenced by various factors such as the driver’s performance. Therefore, knowing the various influential factors related to driver’s performance is very necessary as an effort to realize road traffic safety. This study aims to determine the factors that fall on the accident associated with the driver’s performance and make mathematical modeling factors that affect the accident. Methods of data retrieval were obtained from NTSC secondary data. The data was processed by identifying factors that cause the accident. Furthermore data processing and analysis used the PCA method to obtain mathematical modeling of factors influencing the inter-city bus accidents. The results showed that the main factors that cause accidents are health, discipline, and driver competence.

[The meaning of accidents with biological material to nursing professionals].

PubMed

Magagnini, Maristela Aparecida Magri; Rocha, Suelen Alves; Ayres, Jairo Aparecido

2011-06-01

The aim of this study is to understand what meaning work accidents with exposure to biological material has to nurses. This is an exploratory study with a qualitative approach, and it used Bardin's content analysis. 87 accidents with biological material occurred in the period between 2001 and 2006; among them, eight were seropositive for Hepatitis B and C and HIV/AIDS. An interview with guiding questions was used to collect data. When inquiring these professionals about the meaning of these accidents, four categories emerged: risk situation, danger perception, fatality, and feelings. Although it is not a strategy of clarification, it is a fact that work organization and educative actions have considerable impact in reducing this type of accident, also reducing damage to the life of nurses involved in these accidents.

The Lagerlunda collision and the introduction of color vision testing.

PubMed

Mollon, J D; Cavonius, L R

2012-01-01

In histories of vision testing, the origins of occupational screening for color blindness are often traced to a fatal railroad accident that occurred in Sweden on the night of 14-15 November 1875. The scene of the accident was the estate of Baron Lagerfelt in Östergötland, but the critical events were played out at Linköping (the normal passing place for the northbound and southbound expresses) and at Bankeberg (a small station to which the passing place was reassigned at a few minutes' notice). First to arrive at Bankeberg, the northbound express slowed almost to a halt, but then inexplicably accelerated forwards towards the Lagerlunda estate, despite a sequence of signals from the stationmaster, Uno Björkelund, and a lineman, Oskar Johansson. Soon after the accident, the ophthalmologist Frithiof Holmgren suggested that the engineer of the northbound express, Andersson, or his oiler, Larsson, had been color blind. Neither survived to be tested. Using the records of the subsequent trial and other archival materials, we have re-examined the role of color blindness in the Lagerlunda incident and conclude that the accident cannot be attributed to color blindness alone. Yet the accident undoubtedly had a central role in the introduction of color vision testing by European and North American railroads. To persuade the railroad management to introduce universal screening of employees for color blindness, Holmgren used a dramatic coup de theatre and some unashamed subterfuge. Copyright © 2012 Elsevier Inc. All rights reserved.

The Euratom-Rosatom ERCOSAM-SAMARA projects on containment thermal-hydraulics of current and future LWRs for severe accident management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paladino, D.; Guentay, S.; Andreani, M.

2012-07-01

During a postulated severe accident with core degradation, hydrogen would form in the reactor pressure vessel mainly due to high temperatures zirconium-steam reaction and flow together with steam into the containment where it will mix with the containment atmosphere (steam-air). The hydrogen transport into the containment is a safety concern because it can lead to explosive mixtures through the associated phenomena of condensation, mixing and stratification. The ERCOSAM and SAMARA projects, co-financed by the European Union and the Russia, include various experiments addressing accident scenarios scaled down from existing plant calculations to different thermal-hydraulics facilities (TOSQAN, MISTRA, PANDA, SPOT). Themore » tests sequences aim to investigate hydrogen concentration build-up and stratification during a postulated accident and the effect of the activation of Severe Accident Management systems (SAMs), e.g. sprays, coolers and Passive Auto-catalytic Recombiners (PARs). Analytical activities, performed by the project participants, are an essential component of the projects, as they aim to improve and validate various computational methods. They accompany the projects in the various phases; plant calculations, scaling to generic containment and to the different facilities, planning pre-test and post-test simulations are performed. Code benchmark activities on the basis of conceptual near full scale HYMIX facility will finally provide a further opportunity to evaluate the applicability of the various methods to the study of scaling issues. (authors)« less

Risk assessment of maintenance operations: the analysis of performing task and accident mechanism.

PubMed

Carrillo-Castrillo, Jesús A; Rubio-Romero, Juan Carlos; Guadix, Jose; Onieva, Luis

2015-01-01

Maintenance operations cover a great number of occupations. Most small and medium-sized enterprises lack the appropriate information to conduct risk assessments of maintenance operations. The objective of this research is to provide a method based on the concepts of task and accident mechanisms for an initial risk assessment by taking into consideration the prevalence and severity of the maintenance accidents reported. Data were gathered from 11,190 reported accidents in maintenance operations in the manufacturing sector of Andalusia from 2003 to 2012. By using a semi-quantitative methodology, likelihood and severity were evaluated based on the actual distribution of accident mechanisms in each of the tasks. Accident mechanisms and tasks were identified by using those variables included in the European Statistics of Accidents at Work methodology. As main results, the estimated risk of the most frequent accident mechanisms identified for each of the analysed tasks is low and the only accident mechanisms with medium risk are accidents when lifting or pushing with physical stress on the musculoskeletal system in tasks involving carrying, and impacts against objects after slipping or stumbling for tasks involving movements. The prioritisation of public preventive actions for the accident mechanisms with a higher estimated risk is highly recommended.

Accidents in Building Engineering in the European Union Countries in the Years 2008 - 2014

NASA Astrophysics Data System (ADS)

Harasymiuk, Jolanta; Tadeusz Barski, Janusz

2017-10-01

According to the ESAW1, an accident at work is an event that results in physical or mental harm to the person doing the work. As a result of this incident, fatal accidents may occur (which in the course of one year lead to death of the victim) or non-fatal accidents (that imply at least four full calendar days of absence from work). In the paper the authors present the number and the analysis of the causes of accidents at work in the construction industry in years 2008 - 2014 in 28 countries of the European Union. The descriptive statistics method was used to achieve the intended goal. The accident rate indicator for individual European Union countries has been shown in the analyzed period. The structure and trends of accidents during the period under investigation, divided into two groups: fatal accidents and non-fatal accidents, were presented. Both groups were analyzed for what caused them and what factors affected the quantity (Age of the victim, work experience, month of occurrence). On the basis of the analyzed causes and factors causing accidents in the construction industry in years 2008 - 2014, the classification of EU countries has been shown in terms of accidents. The paper was concluded with a summary.

APT Blanket System Loss-of-Coolant Accident (LOCA) Analysis Based on Initial Conceptual Design - Case 3: External HR Break at Pump Outlet without Pump Trip

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamm, L.L.

1998-10-07

This report is one of a series of reports that document normal operation and accident simulations for the Accelerator Production of Tritium (APT) blanket heat removal (HR) system. These simulations were performed for the Preliminary Safety Analysis Report.

10 CFR 100.11 - Determination of exclusion area, low population zone, and population center distance.

Code of Federal Regulations, 2014 CFR

2014-01-01

... these calculations should be based upon a major accident, hypothesized for purposes of site analysis or... exceeded by those from any accident considered credible. Such accidents have generally been assumed to... total radiation dose to the whole body in excess of 25 rem 2 or a total radiation dose in excess of 300...

10 CFR 100.11 - Determination of exclusion area, low population zone, and population center distance.

Code of Federal Regulations, 2012 CFR

2012-01-01

... these calculations should be based upon a major accident, hypothesized for purposes of site analysis or... exceeded by those from any accident considered credible. Such accidents have generally been assumed to... total radiation dose to the whole body in excess of 25 rem 2 or a total radiation dose in excess of 300...

10 CFR 100.11 - Determination of exclusion area, low population zone, and population center distance.

Code of Federal Regulations, 2013 CFR

2013-01-01

... these calculations should be based upon a major accident, hypothesized for purposes of site analysis or... exceeded by those from any accident considered credible. Such accidents have generally been assumed to... total radiation dose to the whole body in excess of 25 rem 2 or a total radiation dose in excess of 300...

Work accidents and self-esteem of nursing professional in hospital settings.

PubMed

Santos, Sérgio Valverde Marques Dos; Macedo, Flávia Ribeiro Martins; Silva, Luiz Almeida da; Resck, Zelia Marilda Rodrigues; Nogueira, Denismar Alves; Terra, Fábio de Souza

2017-04-20

to analyze the occurrence of work accidents and the self-esteem of nurses in hospitals of a municipality of Minas Gerais. descriptive-analytical and cross-sectional study developed with 393 nursing professionals from three hospitals of a municipality in southern Minas Gerais. The Rosenberg Self-Esteem Scale and a questionnaire to characterize the population and work accidents were used for data collection. Data analysis was performed using Person's chi-squared test, Fisher's exact test, Cronbach's alpha, odds ratio and logistic regression. of the professionals studied, 15% had suffered an accident at work and 70.2% presented high self-esteem. Through the analysis, it was observed that smoking, religious belief and an outstanding event in the career were significantly associated with work accidents. In relation to self-esteem, family income, length of time working in the profession and an outstanding event in the career presented significant associations. factors such as smoking, religious belief, family income, length of time working in the profession and an outstanding event in the career can cause professionals to have accidents and/or cause changes in self-esteem, which can compromise their physical and mental health and their quality of life and work.

[Burden of disease attributable to road traffic accidents in the Friuli Venezia Giulia Region (Northeastern Italy)].

PubMed

Collarile, Paolo; Gobbino, Iliana; Tripani, Nicola; Zeriali, Luca; Dimai, Matteo; Valent, Francesca

2014-01-01

to estimate the health impact of road traffic accidents in the Friuli Venezia Giulia Region, Northeastern Italy. burden of disease (BoD) study. we used data on road traffic accidents collected by the Police in the Friuli Venezia Giulia in 2010 and health data regarding Emergency Room visits, hospital admissions, and deaths. we calculated the Disability Adjusted Life Years (DALY) lost because of road traffic accidents. The kernel density of the DALYs in the region was analyzed and mapped. it was estimated that 3,861 DALYs were lost in 2010. Years lost because of premature deaths outnumbered those lost because of disability. The highest number of DALYs was lost among 15-44-year-old males. Of 14,361 injured persons included in the analysis, only 4,357 were found in the Police database. However, these injuries accounted for 95% of all the DALYs. the present study identified population subgroups with a particularly high impact of road traffic accidents. Educational and Police interventions to prevent accidents should be addressed to those subgroups. In the future, repeating this analysis will allow an evaluation of the effectiveness of preventive interventions in terms of health gains.

Work accidents and self-esteem of nursing professional in hospital settings

PubMed Central

dos Santos, Sérgio Valverde Marques; Macedo, Flávia Ribeiro Martins; da Silva, Luiz Almeida; Resck, Zelia Marilda Rodrigues; Nogueira, Denismar Alves; Terra, Fábio de Souza

2017-01-01

Abstract Objective: to analyze the occurrence of work accidents and the self-esteem of nurses in hospitals of a municipality of Minas Gerais. Method: descriptive-analytical and cross-sectional study developed with 393 nursing professionals from three hospitals of a municipality in southern Minas Gerais. The Rosenberg Self-Esteem Scale and a questionnaire to characterize the population and work accidents were used for data collection. Data analysis was performed using Person's chi-squared test, Fisher's exact test, Cronbach's alpha, odds ratio and logistic regression. Results: of the professionals studied, 15% had suffered an accident at work and 70.2% presented high self-esteem. Through the analysis, it was observed that smoking, religious belief and an outstanding event in the career were significantly associated with work accidents. In relation to self-esteem, family income, length of time working in the profession and an outstanding event in the career presented significant associations. Conclusion: factors such as smoking, religious belief, family income, length of time working in the profession and an outstanding event in the career can cause professionals to have accidents and/or cause changes in self-esteem, which can compromise their physical and mental health and their quality of life and work. PMID:28443993

Dose-dependent analysis of acute medical effects of mixed neutron-gamma radiation from selected severe 235U or 239Pu criticality accidents in USSR, United States, and Argentina.

PubMed

Barabanova, Tatyana; Wiley, Albert L; Bushmanov, Andrey

2012-04-01

Eight of the most severe cases of acute radiation disease (ARS) known to have occurred in humans (as the result of criticality accidents) had survival times less than 120 h (herein defined as "early death"). These accidents were analyzed and are discussed with respect to the specific accident scenarios and the resulting accident-specific, mixed neutron-gamma radiation clinical dose distributions. This analysis concludes that the cardiovascular system appears to be the most critical organ system failure for causing "early death" following approximate total body, mixed gamma-neutron radiation doses greater than 40-50 Gy. The clinical data also suggest that there was definite chest dose dependence in the resulting survival times for these eight workers, who unfortunately suffered profound radiation injury and unusual clinical effects from such high dose radiation exposures. In addition, "toxemic syndrome" is correlated with the irradiation of large volumes of soft tissues. Doses to the hands or legs greater than 80-100 Gy or radiation lung injury also play significant but secondary roles in causing "early death" in accidents delivering chest doses greater than 50 Gy.

Potential effects of the fire protection system sprays at Browns Ferry on fission product transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niemczyk, S.J.

1983-01-01

The fire protection system (FPS) sprays within any nuclear plant are not intended to mitigate radioactive releases to the environment resulting from severe core-damage accidents. However, it has been shown here that during certain postulated severe accident scenarios at the Browns Ferry Nuclear Plant, the functioning of FPS sprays could have a significant impact on the radioactive releases. Thus the effects of those sprays need to be taken into account for realistic estimation of source terms for some accident scenarios. The effects would include direct ones such as cooling of the reactor building atmosphere and scrubbing of radioactivity from it,more » as well as indirect effects such as an altered likelihood of hydrogen burning and flooding of various safety-related pumps in the reactor building basement. Thus some of the impacts of the sprays would be beneficial with respect to mitigating releases to the environment but some others might not be. The effects of the FPS would be very scenario dependent with a wide range of potential effects often existing for a given accident sequence. Any generalization of the specific results presented here for Browns Ferry to other nuclear plants must be done cautiously, as it appears from a preliminary investigation that the relevant physical and operational characteristics of FPS spray systems differ widely among even otherwise apparently similar plants. Likewise the standby gas treatment systems, which substantially impact the effects of the FPS, differ significantly among plants. More work for both Mark I plants and other plants, BWRs and PWRs alike, is indicated so the potential effects of FPS spray systems during severe accidents can be at least ball-parked for more realistic accident analyses.« less

An Examination of Safety Management Systems and Aviation Technologies in the Helicopter Emergency Medical Services Industry

NASA Astrophysics Data System (ADS)

Buckner, Steven A.

The Helicopter Emergency Medical Service (HEMS) industry has a significant role in the transportation of injured patients, but has experienced more accidents than all other segments of the aviation industry combined. With the objective of addressing this discrepancy, this study assesses the effect of safety management systems implementation and aviation technologies utilization on the reduction of HEMS accident rates. Participating were 147 pilots from Federal Aviation Regulations Part 135 HEMS operators, who completed a survey questionnaire based on the Safety Culture and Safety Management System Survey (SCSMSS). The study assessed the predictor value of SMS implementation and aviation technologies to the frequency of HEMS accident rates with correlation and multiple linear regression. The correlation analysis identified three significant positive relationships. HEMS years of experience had a high significant positive relationship with accident rate (r=.90; p<.05); SMS had a moderate significant positive relationship to Night Vision Goggles (NVG) (r=.38; p<.05); and SMS had a slight significant positive relationship with Terrain Avoidance Warning System (TAWS) (r=.234; p<.05). Multiple regression analysis suggested that when combined with NVG, TAWS, and SMS, HEMS years of experience explained 81.4% of the variance in accident rate scores (p<.05), and HEMS years of experience was found to be a significant predictor of accident rates (p<.05). Additional quantitative regression analysis was recommended to replicate the results of this study and to consider the influence of these variables for continued reduction of HEMS accidents, and to induce execution of SMS and aviation technologies from a systems engineering application. Recommendations for practice included the adoption of existing regulatory guidance for a SMS program. A qualitative analysis was also recommended for future study SMS implementation and HEMS accident rate from the pilot's perspective. A quantitative longitudinal study would further explore inferential relationships between the study variables. Current strategies should include the increased utilization of available aviation technology resources as this proactive stance may be beneficial for the establishment of an effective safety culture within the HEMS industry.

Toxic release consequence analysis tool (TORCAT) for inherently safer design plant.

PubMed

Shariff, Azmi Mohd; Zaini, Dzulkarnain

2010-10-15

Many major accidents due to toxic release in the past have caused many fatalities such as the tragedy of MIC release in Bhopal, India (1984). One of the approaches is to use inherently safer design technique that utilizes inherent safety principle to eliminate or minimize accidents rather than to control the hazard. This technique is best implemented in preliminary design stage where the consequence of toxic release can be evaluated and necessary design improvements can be implemented to eliminate or minimize the accidents to as low as reasonably practicable (ALARP) without resorting to costly protective system. However, currently there is no commercial tool available that has such capability. This paper reports on the preliminary findings on the development of a prototype tool for consequence analysis and design improvement via inherent safety principle by utilizing an integrated process design simulator with toxic release consequence analysis model. The consequence analysis based on the worst-case scenarios during process flowsheeting stage were conducted as case studies. The preliminary finding shows that toxic release consequences analysis tool (TORCAT) has capability to eliminate or minimize the potential toxic release accidents by adopting the inherent safety principle early in preliminary design stage. 2010 Elsevier B.V. All rights reserved.

Characteristics of worker accidents on NYSDOT construction projects.

PubMed

Mohan, Satish; Zech, Wesley C

2005-01-01

This paper aims at providing cost-effective safety measures to protect construction workers in highway work zones, based on real data. Two types of accidents that occur in work zones were: (a) construction work area accidents, and (b) traffic accidents involving construction worker(s). A detailed analysis of work zone accidents involving 36 fatalities and 3,055 severe injuries to construction workers on New York State Department of Transportation (NYSDOT) construction projects from 1990 to 2001 established that five accident types: (a) Struck/Pinned by Large Equipment, (b) Trip or Fall (elevated), (c) Contact w/Electrical or Gas Utility, (d) Struck-by Moving/Falling Load, and (e) Crane/Lift Device Failure accounted for nearly 96% of the fatal accidents, nearly 63% of the hospital-level injury accidents, and nearly 91% of the total costs. These construction work area accidents had a total cost of $133.8 million. Traffic accidents that involve contractors' employees were also examined. Statistical analyses of the traffic accidents established that five traffic accident types: (a) Work Space Intrusion, (b) Worker Struck-by Vehicle Inside Work Space, (c) Flagger Struck-by Vehicle, (d) Worker Struck-by Vehicle Entering/Exiting Work Space, and (e) Construction Equipment Struck-by Vehicle Inside Work Space accounted for nearly 86% of the fatal, nearly 70% of the hospital-level injury and minor injury traffic accidents, and $45.4 million (79.4%) of the total traffic accident costs. The results of this paper provide real statistics on construction worker related accidents reported on construction work zones. Potential preventions based on real statistics have also been suggested. The ranking of accident types, both within the work area as well as in traffic, will guide the heavy highway contractor and owner agencies in identifying the most cost effective safety preventions.

Investigations on optimization of accident management measures following a station blackout accident in a VVER-1000 pressurized water reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tusheva, P.; Schaefer, F.; Kliem, S.

2012-07-01

The reactor safety issues are of primary importance for preserving the health of the population and ensuring no release of radioactivity and fission products into the environment. A part of the nuclear research focuses on improvement of the safety of existing nuclear power plants. Studies, research and efforts are a continuing process at improving the safety and reliability of existing and newly developed nuclear power plants at prevention of a core melt accident. Station blackout (loss of AC power supply) is one of the dominant accidents taken into consideration at performing accident analysis. In case of multiple failures of safetymore » systems it leads to a severe accident. To prevent an accident to turn into a severe one or to mitigate the consequences, accident management measures must be performed. The present paper outlines possibilities for application and optimization of accident management measures following a station blackout accident. Assessed is the behaviour of the nuclear power plant during a station blackout accident without accident management measures and with application of primary/secondary side oriented accident management measures. Discussed are the possibilities for operators ' intervention and the influence of the performed accident management measures on the course of the accident. Special attention has been paid to the effectiveness of the passive feeding and physical phenomena having an influence on the system behaviour. The performed simulations show that the effectiveness of the secondary side feeding procedure can be limited due to an early evaporation or flashing effects in the feed water system. The analyzed cases show that the effectiveness of the accident management measures strongly depends on the initiation criteria applied for depressurization of the reactor coolant system. (authors)« less

Interim MELCOR Simulation of the Fukushima Daiichi Unit 2 Accident Reactor Core Isolation Cooling Operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, Kyle W.; Gauntt, Randall O.; Cardoni, Jeffrey N.

2013-11-01

Data, a brief description of key boundary conditions, and results of Sandia National Laboratories’ ongoing MELCOR analysis of the Fukushima Unit 2 accident are given for the reactor core isolation cooling (RCIC) system. Important assumptions and related boundary conditions in the current analysis additional to or different than what was assumed/imposed in the work of SAND2012-6173 are identified. This work is for the U.S. Department of Energy’s Nuclear Energy University Programs fiscal year 2014 Reactor Safety Technologies Research and Development Program RC-7: RCIC Performance under Severe Accident Conditions.

Assessing the safety effects of cooperative intelligent transport systems: A bowtie analysis approach.

PubMed

Ehlers, Ute Christine; Ryeng, Eirin Olaussen; McCormack, Edward; Khan, Faisal; Ehlers, Sören

2017-02-01

The safety effects of cooperative intelligent transport systems (C-ITS) are mostly unknown and associated with uncertainties, because these systems represent emerging technology. This study proposes a bowtie analysis as a conceptual framework for evaluating the safety effect of cooperative intelligent transport systems. These seek to prevent road traffic accidents or mitigate their consequences. Under the assumption of the potential occurrence of a particular single vehicle accident, three case studies demonstrate the application of the bowtie analysis approach in road traffic safety. The approach utilizes exemplary expert estimates and knowledge from literature on the probability of the occurrence of accident risk factors and of the success of safety measures. Fuzzy set theory is applied to handle uncertainty in expert knowledge. Based on this approach, a useful tool is developed to estimate the effects of safety-related cooperative intelligent transport systems in terms of the expected change in accident occurrence and consequence probability. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermal-hydraulic analysis of N Reactor graphite and shield cooling system performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Low, J.O.; Schmitt, B.E.

1988-02-01

A series of bounding (worst-case) calculations were performed using a detailed hydrodynamic RELAP5 model of the N Reactor graphite and shield cooling system (GSCS). These calculations were specifically aimed to answer issues raised by the Westinghouse Independent Safety Review (WISR) committee. These questions address the operability of the GSCS during a worst-case degraded-core accident that requires the GDCS to mitigate the consequences of the accident. An accident scenario previously developed was designed as the hydrogen-mitigation design-basis accident (HMDBA). Previous HMDBA heat transfer analysis,, using the TRUMP-BD code, was used to define the thermal boundary conditions that the GSDS may bemore » exposed to. These TRUMP/HMDBA analysis results were used to define the bounding operating conditions of the GSCS during the course of an HMDBA transient. Nominal and degraded GSCS scenarios were investigated using RELAP5 within or at the bounds of the HMDBA transient. 10 refs., 42 figs., 10 tabs.« less

[Accidents at work and occupational diseases trend in agriculture insurance management. The contribution of INAIL data's for the knowledge of a worrying phenomenon].

PubMed

Calandriello, Luigi; Goggiamani, Angela; Ienzi, Emanuela; Naldini, Silvia; Orsini, Dario

2013-01-01

The author's describe accidents at work and occupational diseases outcome's measure in Agricolture insurance management acquired through statistical approach based on data processing provided by INAIL Bank data. Accident's incidence in Agricolture is compared to main insurance managements, using frequency index of accidents appearance selected on line of work and type of consequence. Concerning occupational diseases the authors describes the complaints and compensation with the comparison referring the analysis to statistical general data. The data define a worrying phenomenon.

Risk-based Analysis of Construction Accidents in Iran During 2007-2011-Meta Analyze Study.

PubMed

Amiri, Mehran; Ardeshir, Abdollah; Fazel Zarandi, Mohammad Hossein

2014-04-01

The present study aimed to investigate the characteristics of occupational accidents and frequency and severity of work related accidents in the construction industry among Iranian insured workers during the years 20072011. The Iranian Social Security Organization (ISSO) accident database containing 21,864 cases between the years 2007-2011 was applied in this study. In the next step, Total Accident Rate (TRA), Total Severity Index (TSI), and Risk Factor (RF) were defined. The core of this work is devoted to analyzing the data from different perspectives such as age of workers, occupation and construction phase, day of the week, time of the day, seasonal analysis, regional considerations, type of accident, and body parts affected. Workers between 15-19 years old (TAR=13.4%) are almost six times more exposed to risk of accident than the average of all ages (TAR=2.51%). Laborers and structural workers (TAR=66.6%) and those working at heights (TAR=47.2%) experience more accidents than other groups of workers. Moreover, older workers over 65 years old (TSI=1.97%> average TSI=1.60%), work supervisors (TSI=12.20% >average TSI=9.09%), and night shift workers (TSI=1.89% >average TSI=1.47%) are more prone to severe accidents. It is recommended that laborers, young workers, weekend and night shift workers be supervised more carefully in the workplace. Use of Personal Protective Equipment (PPE) should be compulsory in working environments, and special attention should be undertaken to people working outdoors and at heights. It is also suggested that policymakers pay more attention to the improvement of safety conditions in deprived and cold western regions.

ADAM: An Accident Diagnostic,Analysis and Management System - Applications to Severe Accident Simulation and Management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zavisca, M.J.; Khatib-Rahbar, M.; Esmaili, H.

2002-07-01

The Accident Diagnostic, Analysis and Management (ADAM) computer code has been developed as a tool for on-line applications to accident diagnostics, simulation, management and training. ADAM's severe accident simulation capabilities incorporate a balance of mechanistic, phenomenologically based models with simple parametric approaches for elements including (but not limited to) thermal hydraulics; heat transfer; fuel heatup, meltdown, and relocation; fission product release and transport; combustible gas generation and combustion; and core-concrete interaction. The overall model is defined by a relatively coarse spatial nodalization of the reactor coolant and containment systems and is advanced explicitly in time. The result is to enablemore » much faster than real time (i.e., 100 to 1000 times faster than real time on a personal computer) applications to on-line investigations and/or accident management training. Other features of the simulation module include provision for activation of water injection, including the Engineered Safety Features, as well as other mechanisms for the assessment of accident management and recovery strategies and the evaluation of PSA success criteria. The accident diagnostics module of ADAM uses on-line access to selected plant parameters (as measured by plant sensors) to compute the thermodynamic state of the plant, and to predict various margins to safety (e.g., times to pressure vessel saturation and steam generator dryout). Rule-based logic is employed to classify the measured data as belonging to one of a number of likely scenarios based on symptoms, and a number of 'alarms' are generated to signal the state of the reactor and containment. This paper will address the features and limitations of ADAM with particular focus on accident simulation and management. (authors)« less

Risk-based Analysis of Construction Accidents in Iran During 2007-2011-Meta Analyze Study

PubMed Central

AMIRI, Mehran; ARDESHIR, Abdollah; FAZEL ZARANDI, Mohammad Hossein

2014-01-01

Abstract Background The present study aimed to investigate the characteristics of occupational accidents and frequency and severity of work related accidents in the construction industry among Iranian insured workers during the years 20072011. Methods The Iranian Social Security Organization (ISSO) accident database containing 21,864 cases between the years 2007-2011 was applied in this study. In the next step, Total Accident Rate (TRA), Total Severity Index (TSI), and Risk Factor (RF) were defined. The core of this work is devoted to analyzing the data from different perspectives such as age of workers, occupation and construction phase, day of the week, time of the day, seasonal analysis, regional considerations, type of accident, and body parts affected. Results Workers between 15-19 years old (TAR=13.4%) are almost six times more exposed to risk of accident than the average of all ages (TAR=2.51%). Laborers and structural workers (TAR=66.6%) and those working at heights (TAR=47.2%) experience more accidents than other groups of workers. Moreover, older workers over 65 years old (TSI=1.97%> average TSI=1.60%), work supervisors (TSI=12.20% >average TSI=9.09%), and night shift workers (TSI=1.89% >average TSI=1.47%) are more prone to severe accidents. Conclusion It is recommended that laborers, young workers, weekend and night shift workers be supervised more carefully in the workplace. Use of Personal Protective Equipment (PPE) should be compulsory in working environments, and special attention should be undertaken to people working outdoors and at heights. It is also suggested that policymakers pay more attention to the improvement of safety conditions in deprived and cold western regions. PMID:26005662

Noise as an explanatory factor in work-related fatality reports

PubMed Central

Deshaies, Pierre; Martin, Richard; Belzile, Danny; Fortier, Pauline; Laroche, Chantal; Leroux, Tony; Nélisse, Hugues; Girard, Serge-André; Arcand, Robert; Poulin, Maurice; Picard, Michel

2015-01-01

Noise exposure in the workplace is a common reality in Québec, Canada as it is elsewhere. However, the extent to which noise acts as a causal or contributive factor in industrial work-related accidents has not been studied thoroughly despite its plausibility. This article aims to describe the importance or potential importance, during investigations looking into the specific causes of each work-related fatal accident, of noise as an explanatory factor. The written information contained in the accident reports pertaining to contextual and technical elements were used. The study used multiple case qualitative content analysis. This descriptive study was based on the content analysis of the 788 reports from the Commission de la santé et de la sécurité du travail du Québec [Workers’ Compensation Board (WCB)] investigating the fatal work-related accidents between 1990 and 2005. The study was descriptive (number and percentages). Noise was explicitly stated as one of the explanatory factors for the fatal outcome in 2.2% (17/788) of the fatal accidents, particularly when the work involved vehicular movement or the need to communicate between workers. Noise was not typically considered a unique cause in the accident, notably because the investigators considered that the accident would have probably occurred due to other risk factors (for example, disregard of safety rules, shortcomings in work methods, and inadequate training). Noise is an important risk factor when communication is involved in work. Since noise is ubiquitous and may also interfere with vigilance and other risk factors for accidents, it may be a much more important contributing factor to accidents than is currently recognized. PMID:26356371

Noise as an explanatory factor in work-related fatality reports.

PubMed

Deshaies, Pierre; Martin, Richard; Belzile, Danny; Fortier, Pauline; Laroche, Chantal; Leroux, Tony; Nélisse, Hugues; Girard, Serge-André; Arcand, Robert; Poulin, Maurice; Picard, Michel

2015-01-01

Noise exposure in the workplace is a common reality in Québec, Canada as it is elsewhere. However, the extent to which noise acts as a causal or contributive factor in industrial work-related accidents has not been studied thoroughly despite its plausibility. This article aims to describe the importance or potential importance, during investigations looking into the specific causes of each work-related fatal accident, of noise as an explanatory factor. The written information contained in the accident reports pertaining to contextual and technical elements were used. The study used multiple case qualitative content analysis. This descriptive study was based on the content analysis of the 788 reports from the Commission de la santé et de la sécurité du travail du Québec [Workers' Compensation Board (WCB)] investigating the fatal work-related accidents between 1990 and 2005. The study was descriptive (number and percentages). Noise was explicitly stated as one of the explanatory factors for the fatal outcome in 2.2% (17/788) of the fatal accidents, particularly when the work involved vehicular movement or the need to communicate between workers. Noise was not typically considered a unique cause in the accident, notably because the investigators considered that the accident would have probably occurred due to other risk factors (for example, disregard of safety rules, shortcomings in work methods, and inadequate training). Noise is an important risk factor when communication is involved in work. Since noise is ubiquitous and may also interfere with vigilance and other risk factors for accidents, it may be a much more important contributing factor to accidents than is currently recognized.

Balloon crash damage and injuries: an analysis of 86 accidents, 2000-2004.

PubMed

de Voogt, Alexander J; van Doorn, Robert R A

2006-05-01

General aviation accounts for the majority of aviation crashes and casualties in the United States. The role of ballooning in these statistics is not regularly studied. Since 2001, the National Transportation and Safety Board has made its accident reports more readily available, which presents opportunities for further study. This study analyzes and compares a 5-yr period of accident reports and includes an analysis of injuries and balloon damage in hot-air and gas balloon accidents. Balloon crash 2-page briefs and 5-page accident reports published by the National Transportation and Safety Board for the 5-yr time period 2000-2004 were examined. Data collected in the investigation of these crashes were analyzed and compared with the epidemiological data collected in earlier research. In 86 crashes during a 5-yr period, there were 4 fatalities and 75 people were seriously injured. Only one accident was reported involving a student pilot. Broken ankles and legs have been the most commonly recorded serious injury, but could not be linked to the severity of damage to the balloon. The absence of student pilot accidents may be explained by possible stricter supervision. Balloon basket and envelopes appear of sufficient quality to withstand crashes, but improving the protection of passengers during hard landings should help to decrease the number of serious injuries in ballooning.

A systemic analysis of South Korea Sewol ferry accident - Striking a balance between learning and accountability.

PubMed

Kee, Dohyung; Jun, Gyuchan Thomas; Waterson, Patrick; Haslam, Roger

2017-03-01

The South Korea Sewol ferry accident in April 2014 claimed the lives of over 300 passengers and led to criminal charges of 399 personnel concerned including imprisonment of 154 of them as of Oct 2014. Blame and punishment culture can be prevalent in a more hierarchical society like South Korea as shown in the aftermath of this disaster. This study aims to analyse the South Korea ferry accident using Rasmussen's risk management framework and the associated AcciMap technique and to propose recommendations drawn from an AcciMap-based focus group with systems safety experts. The data for the accident analysis were collected mainly from an interim investigation report by the Board of Audit and Inspection of Korea and major South Korean and foreign newspapers. The analysis showed that the accident was attributed to many contributing factors arising from front-line operators, management, regulators and government. It also showed how the multiple factors including economic, social and political pressures and individual workload contributed to the accident and how they affected each other. This AcciMap was presented to 27 safety researchers and experts at 'the legacy of Jens Rasmussen' symposium adjunct to ODAM2014. Their recommendations were captured through a focus group. The four main recommendations include forgive (no blame and punishment on individuals), analyse (socio-technical system-based), learn (from why things do not go wrong) and change (bottom-up safety culture and safety system management). The findings offer important insights into how this type of accident should be understood, analysed and the subsequent response. Copyright © 2016 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattison, M.B.; Thatcher, T.A.; Knudsen, J.K.

The US Nuclear Regulatory Commission (NRC) has been using full-power. Level 1, limited-scope risk models for the Accident Sequence Precursor (ASP) program for over fifteen years. These models have evolved and matured over the years, as have probabilistic risk assessment (PRA) and computer technologies. Significant upgrading activities have been undertaken over the past three years, with involvement from the Offices of Nuclear Reactor Regulation (NRR), Analysis and Evaluation of Operational Data (AEOD), and Nuclear Regulatory Research (RES), and several national laboratories. Part of these activities was an RES-sponsored feasibility study investigating the ability to extend the ASP models to includemore » contributors to core damage from events initiated with the reactor at low power or shutdown (LP/SD), both internal events and external events. This paper presents only the LP/SD internal event modeling efforts.« less

Physician flight accidents.

DOT National Transportation Integrated Search

1966-09-01

An analysis of physician flight accidents during the period 1964-1965 is presented. More than thirty physicians sustained fatal injuries while piloting light aircraft: a fatality record four times the ratio of physician pilots in the general aviation...

Early Warning: Development of Confidential Incident Reporting Systems

NASA Technical Reports Server (NTRS)

OLeary, Mike J.; Chappell, Sheryl L.; Connell, Linda (Technical Monitor)

1996-01-01

Accidents hardly ever happen without warning. The combination, or sequence, of failures and mistakes that cause an accident may indeed be unique but the individual failures and mistakes rarely are. In the USA in 1974 the crews on two different aircraft misunderstood the same aeronautical chart and descended towards their destination dangerously early towards a mountain. The first crew were in good weather conditions and could see the mountain and resolved their misinterpretation of the chart. The second crew six weeks later were not so lucky. In cloud they had no clues to point out their mistake nor the presence of the mountain. The resulting crash and the ensuing inquiry, which brought to light the previous incident, shocked the country but gave it the impetus to instigate a safety reporting system. This system eventually became the NASA's Aviation Safety Reporting System (ASRS). The programme collects incident reports from pilots, controllers, mechanics, cabin attendants and many others involved in aviation operations. By disseminating this safety information the ASRS has helped enormously to give US airlines and airspace the highest safety standards. Accident prevention is a goal sought by everyone in the aviation industry and establishing effective incident reporting programmes can go a long way toward achieving that goal. This article will describe the steps and issues required to establish an incident reporting system. The authors summarize the lessons learned from the ASRS, now in its twentieth year of operation and from the Confidential Human Factors Reporting (HER) Programme run by British Airways, an airline that is a recognized world leader in safety reporting and analysis. The differences between government and airline operation of confidential safety reporting systems will be addressed.

Demographic variables in coal miners’ safety attitude

NASA Astrophysics Data System (ADS)

Yin, Wen-wen; Wu, Xiang; Ci, Hui-Peng; Qin, Shu-Qi; Liu, Jia-Long

2017-03-01

To change unsafe behavior through adjusting people’s safety attitudes has become an important measure to prevent accidents. Demographic variables, as influential factors of safety attitude, are fundamental and essential for the research. This research does a questionnaire survey among coal mine industry workers, and makes variance analysis and correlation analysis of the results in light of age, length of working years, educational level and experiences of accidents. The results show that the coal miners’ age, length of working years and accident experiences correlate lowly with safety attitudes, and those older coal miners with longer working years have better safety attitude, as coal miners without experiences of accident do.However, educational level has nothing to do with the safety attitude. Therefore, during the process of safety management, coal miners with different demographic characteristics should be put more attention to.

[Reconstruction of Vehicle-human Crash Accident and Injury Analysis Based on 3D Laser Scanning, Multi-rigid-body Reconstruction and Optimized Genetic Algorithm].

PubMed

Sun, J; Wang, T; Li, Z D; Shao, Y; Zhang, Z Y; Feng, H; Zou, D H; Chen, Y J

2017-12-01

To reconstruct a vehicle-bicycle-cyclist crash accident and analyse the injuries using 3D laser scanning technology, multi-rigid-body dynamics and optimized genetic algorithm, and to provide biomechanical basis for the forensic identification of death cause. The vehicle was measured by 3D laser scanning technology. The multi-rigid-body models of cyclist, bicycle and vehicle were developed based on the measurements. The value range of optimal variables was set. A multi-objective genetic algorithm and the nondominated sorting genetic algorithm were used to find the optimal solutions, which were compared to the record of the surveillance video around the accident scene. The reconstruction result of laser scanning on vehicle was satisfactory. In the optimal solutions found by optimization method of genetic algorithm, the dynamical behaviours of dummy, bicycle and vehicle corresponded to that recorded by the surveillance video. The injury parameters of dummy were consistent with the situation and position of the real injuries on the cyclist in accident. The motion status before accident, damage process by crash and mechanical analysis on the injury of the victim can be reconstructed using 3D laser scanning technology, multi-rigid-body dynamics and optimized genetic algorithm, which have application value in the identification of injury manner and analysis of death cause in traffic accidents. Copyright© by the Editorial Department of Journal of Forensic Medicine

Final safety analysis report for the Galileo mission: Volume 3 (Book 2), Nuclear risk analysis document: Appendices: Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-01-25

It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with ifmore » there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.« less

Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015.

PubMed

Mehmandar, Mohammadreza; Soori, Hamid; Mehrabi, Yadolah

2016-01-01

Predicting the trend in traffic accidents deaths and its analysis can be a useful tool for planning and policy-making, conducting interventions appropriate with death trend, and taking the necessary actions required for controlling and preventing future occurrences. Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015. It was a cross-sectional study. All the information related to fatal traffic accidents available in the database of Iran Legal Medicine Organization from 2004 to the end of 2013 were used to determine the change points (multi-variable time series analysis). Using autoregressive integrated moving average (ARIMA) model, traffic accidents death rates were predicted for 2014 and 2015, and a comparison was made between this rate and the predicted value in order to determine the efficiency of the model. From the results, the actual death rate in 2014 was almost similar to that recorded for this year, while in 2015 there was a decrease compared with the previous year (2014) for all the months. A maximum value of 41% was also predicted for the months of January and February, 2015. From the prediction and analysis of the death trends, proper application and continuous use of the intervention conducted in the previous years for road safety improvement, motor vehicle safety improvement, particularly training and culture-fostering interventions, as well as approval and execution of deterrent regulations for changing the organizational behaviors, can significantly decrease the loss caused by traffic accidents.

Safety analysis report for the Galileo Mission. Volume 3, book 2: Nuclear risk analysis document. Appendices, revision 1

NASA Astrophysics Data System (ADS)

1989-01-01

It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with if there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.

Professional experience and traffic accidents/near-miss accidents among truck drivers.

PubMed

Girotto, Edmarlon; Andrade, Selma Maffei de; González, Alberto Durán; Mesas, Arthur Eumann

2016-10-01

To investigate the relationship between the time working as a truck driver and the report of involvement in traffic accidents or near-miss accidents. A cross-sectional study was performed with truck drivers transporting products from the Brazilian grain harvest to the Port of Paranaguá, Paraná, Brazil. The drivers were interviewed regarding sociodemographic characteristics, working conditions, behavior in traffic and involvement in accidents or near-miss accidents in the previous 12 months. Subsequently, the participants answered a self-applied questionnaire on substance use. The time of professional experience as drivers was categorized in tertiles. Statistical analyses were performed through the construction of models adjusted by multinomial regression to assess the relationship between the length of experience as a truck driver and the involvement in accidents or near-miss accidents. This study included 665 male drivers with an average age of 42.2 (±11.1) years. Among them, 7.2% and 41.7% of the drivers reported involvement in accidents and near-miss accidents, respectively. In fully adjusted analysis, the 3rd tertile of professional experience (>22years) was shown to be inversely associated with involvement in accidents (odds ratio [OR] 0.29; 95% confidence interval [CI] 0.16-0.52) and near-miss accidents (OR 0.17; 95% CI 0.05-0.53). The 2nd tertile of professional experience (11-22 years) was inversely associated with involvement in accidents (OR 0.63; 95% CI 0.40-0.98). An evident relationship was observed between longer professional experience and a reduction in reporting involvement in accidents and near-miss accidents, regardless of age, substance use, working conditions and behavior in traffic. Copyright © 2016 Elsevier Ltd. All rights reserved.

Accidents in the greenhouse-construction industry of SE Spain.

PubMed

Pérez-Alonso, José; Carreño-Ortega, Angel; Vázquez-Cabrera, Fernando J; Callejón-Ferre, Angel Jesús

2012-01-01

This work analyses the labour accidents in the greenhouse-construction industry of SE Spain for the period 1999-2007 through a sample of 180 accident reports. The accidents were characterised by studying 5 variables in order to know the day of the week in which the accident occurred, the hour of the day of the accident, type of accident, the region of Spain in which the accident happened, and the resulting injury. The data characterising the accidents were submitted to a descriptive multiple-correspondence analysis. The incidence of accidents in the greenhouse-construction industry presented a high mean value of 15133.7 per 100,000 workers per year. The days with the greatest incidence of accidents were Thursday and Monday, while the period of greatest number of accidents occurred in the first 4h of the workday. No significant correspondence was found between the day of the week, the hour of the day, or any of the other 3 variables studied. The types of accidents with most frequency were: cuts, punctures, contact with hard or rough material, overexertion, and falls from one level to another. The most affected parts of the anatomy were the eyes, thorax, back, sides, lower legs, and feet. The most common types of injury were bone fractures, twists and sprains, distended muscles, contusions, and being crushed. The study calls attention to the high number of accidents at work, which needs to be corrected by fulfilment of safety regulations at work, on the part of the company. Finally, recommendations are made to correct this situation of high number of accidents at work. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Frequency of Specific Categories of Aviation Accidents and Incidents During 2001-2010

NASA Technical Reports Server (NTRS)

Evans, Joni K.

2014-01-01

The purpose of this study was to determine the types of accidents or incidents that are most important to the aviation safety risk. All accidents and incidents from 2001-2010 were assigned occurrence categories based on the taxonomy developed by the Commercial Aviation Safety Team/International Civil Aviation Organization (CAST/ICAO) Common Taxonomy Team (CICTT). The most frequently recorded categories were selected within each of five metrics: total accidents, fatal accidents, total injuries, fatal injuries and total incidents. This analysis was done separately for events within Part 121, Scheduled Part 135, Non-Scheduled Part 135 and Part 91. Combining those five sets of categories resulted in groups of between seven and eleven occurrence categories, depending on the flight operation. These groups represent 65-85% of all accidents and 68-81% of incidents.

Space Propulsion Hazards Analysis Manual (SPHAM). Volume 2. Appendices

DTIC Science & Technology

1988-10-01

lb. RESTRICTIVE MARKINGS UNCLASSIFIED 2a. SECURITY CLASSIFICATION AUTHORITY 3 . DISTRIBUTION/AVAILABILITY OF REPORT Approved for public release...Volume I Chapter 2 - Requirementb and the Hazards Analysis Process .... Volume I Chapter 3 - Accident Scenarios...list of the hazardous materials that are discussed; 3 ) description of the failure scenarios; 4) type of post-accident environment that is discussed

Analysis of roadside inspection data and its relationship to accident and safety/compliance review data and reviews of previous and ongoing research in these areas

DOT National Transportation Integrated Search

1993-01-01

The main objective of the present study is to analyze roadside inspection data and its relationship to safety/compliance review and accident data. Data used for this analysis is provided by the Office of Motor Carriers and includes a sample of larger...

INDUSTRIAL/MILITARY ACTIVITY-INITIATED ACCIDENT SCREENING ANALYSIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

D.A. Kalinich

1999-09-27

Impacts due to nearby installations and operations were determined in the Preliminary MGDS Hazards Analysis (CRWMS M&O 1996) to be potentially applicable to the proposed repository at Yucca Mountain. This determination was conservatively based on limited knowledge of the potential activities ongoing on or off the Nevada Test Site (NTS). It is intended that the Industrial/Military Activity-Initiated Accident Screening Analysis provided herein will meet the requirements of the ''Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants'' (NRC 1987) in establishing whether this external event can be screened from further consideration or must be includedmore » as a design basis event (DBE) in the development of accident scenarios for the Monitored Geologic Repository (MGR). This analysis only considers issues related to preclosure radiological safety. Issues important to waste isolation as related to impact from nearby installations will be covered in the MGR performance assessment.« less

Identification and Phylogenetic Analysis of Tityus pachyurus and Tityus obscurus Novel Putative Na+-Channel Scorpion Toxins

PubMed Central

Guerrero-Vargas, Jimmy A.; Mourão, Caroline B. F.; Quintero-Hernández, Verónica; Possani, Lourival D.; Schwartz, Elisabeth F.

2012-01-01

Background Colombia and Brazil are affected by severe cases of scorpionism. In Colombia the most dangerous accidents are caused by Tityus pachyurus that is widely distributed around this country. In the Brazilian Amazonian region scorpion stings are a common event caused by Tityus obscurus. The main objective of this work was to perform the molecular cloning of the putative Na+-channel scorpion toxins (NaScTxs) from T. pachyurus and T. obscurus venom glands and to analyze their phylogenetic relationship with other known NaScTxs from Tityus species. Methodology/Principal Findings cDNA libraries from venom glands of these two species were constructed and five nucleotide sequences from T. pachyurus were identified as putative modulators of Na+-channels, and were named Tpa4, Tpa5, Tpa6, Tpa7 and Tpa8; the latter being the first anti-insect excitatory β-class NaScTx in Tityus scorpion venom to be described. Fifteen sequences from T. obscurus were identified as putative NaScTxs, among which three had been previously described, and the others were named To4 to To15. The peptides Tpa4, Tpa5, Tpa6, To6, To7, To9, To10 and To14 are closely related to the α-class NaScTxs, whereas Tpa7, Tpa8, To4, To8, To12 and To15 sequences are more related to the β-class NaScTxs. To5 is possibly an arthropod specific toxin. To11 and To13 share sequence similarities with both α and β NaScTxs. By means of phylogenetic analysis using the Maximum Parsimony method and the known NaScTxs from Tityus species, these toxins were clustered into 14 distinct groups. Conclusions/Significance This communication describes new putative NaScTxs from T. pachyurus and T. obscurus and their phylogenetic analysis. The results indicate clear geographic separation between scorpions of Tityus genus inhabiting the Amazonian and Mountain Andes regions and those distributed over the Southern of the Amazonian rainforest. Based on the consensus sequences for the different clusters, a new nomenclature for the NaScTxs is proposed. PMID:22355312

[The drama of hyperextension trauma--chronic whiplash syndrome with its neuropsychological and psychiatric findings. An analysis of 80 cases from expert assessment].

PubMed

Kissel, W

1999-10-28

The problem "whiplash associated disorder" was studied in a multidisciplinary analysis of 80 patients who all had a "simple whiplash-accident", this means a whiplash-accident without concomitant head trauma apart from contact with the car seat and without unconsciousness. The opinions of a rheumatologist and of a psychiatrist were considered in each case, and in 47 patients, a neuropsychological expertise was present. 43% of the patients who had been neuropsychologically tested revealed specific cognitive deficits as they are described after mild traumatic brain injuries and after whiplash accidents. Symptoms related to a pretraumatic cognitive disease were not found in any of the cases. Most patients had been professionally active at the time of the accident, some performing activities requiring a high level of cognitive skill. 66% percent of the study group showed psychological disturbances reducing the working capacity. There was no evidence for preexisting traumatic psychiatric symptoms. In many cases the psychiatric disturbances were accident-related, either reactive to the cognitive deficiencies or resulting from chronic pain. We assume that the "simple whiplash-accident" can cause chronic disturbances of brain function. In the etiology, a mild traumatic brain damage must be considered, this means an organic damage and not only a functional brain disorder. These brain function disturbances are often masked by the pure psychiatric symptoms, therefore they must be carefully searched for. Injured patients, who do not regain their working capacity after the accident, should be explored in a neuropsychological as well as in a psychiatric mode as early as possible after the accident.

Off-road truck-related accidents in U.S. mines

PubMed Central

Dindarloo, Saeid R.; Pollard, Jonisha P.; Siami-Irdemoosa, Elnaz

2016-01-01

Introduction Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. Methods A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Results Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5 years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. Conclusions The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Practical application Analyzing injury data using data mining techniques provides some insight into attributes that are associated with high accuracies for predicting injury severity. PMID:27620937

Off-road truck-related accidents in U.S. mines.

PubMed

Dindarloo, Saeid R; Pollard, Jonisha P; Siami-Irdemoosa, Elnaz

2016-09-01

Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Analyzing injury data using data mining techniques provides some insight into attributes that are associated with high accuracies for predicting injury severity. Copyright © 2016 Elsevier Ltd and National Safety Council. All rights reserved.

The role of personality traits and driving experience in self-reported risky driving behaviors and accident risk among Chinese drivers.

PubMed

Tao, Da; Zhang, Rui; Qu, Xingda

2017-02-01

The purpose of this study was to explore the role of personality traits and driving experience in the prediction of risky driving behaviors and accident risk among Chinese population. A convenience sample of drivers (n=511; mean (SD) age=34.2 (8.8) years) completed a self-report questionnaire that was designed based on validated scales for measuring personality traits, risky driving behaviors and self-reported accident risk. Results from structural equation modeling analysis demonstrated that the data fit well with our theoretical model. While showing no direct effects on accident risk, personality traits had direct effects on risky driving behaviors, and yielded indirect effects on accident risk mediated by risky driving behaviors. Both driving experience and risky driving behaviors directly predicted accident risk and accounted for 15% of its variance. There was little gender difference in personality traits, risky driving behaviors and accident risk. The findings emphasized the importance of personality traits and driving experience in the understanding of risky driving behaviors and accident risk among Chinese drivers and provided new insight into the design of evidence-based driving education and accident prevention interventions. Copyright © 2016 Elsevier Ltd. All rights reserved.

A decade of occupational accidents due to direct or indirect electrical contact in the primary, secondary and tertiary sectors in Spain (2003-2012).

PubMed

Castillo-Rosa, Juan; Suárez-Cebador, Manuel; Rubio-Romero, Juan Carlos; Aguado, Jose Antonio

2017-03-01

Occupational accidents caused by electrical contact are a major concern worldwide due to their severe consequences. The study conducted is based on an analysis of the evolution of incidence rates and dependence between variables for 14,022 electrical accidents occurring in Spain between 2003 and 2012. The results show that electrical accidents as a whole are 3.6 times more likely to have severe consequences than the rest of the accidents in the country. This proportion is even nine times greater in the case of fatal accidents. They also confirm a significant relationship between the severity of this type of accidents and the economic sector in which they occur. On the other hand, there is a positive trend in the reduction of the incidence rate, especially in relation to direct contact, although unexpectedly the rate of accidents due to indirect contact is on the rise. Thus, preventing electrical occupational accidents requires efforts to guarantee adequate training adapted to the needs of workers in the various economic sectors. Furthermore, those responsible for safety should work to implement mechanisms to monitor and control compliance with efficient protective measures against electrical contact.

Occupational accidents among mototaxi drivers.

PubMed

Amorim, Camila Rego; de Araújo, Edna Maria; de Araújo, Tânia Maria; de Oliveira, Nelson Fernandes

2012-03-01

The use of motorcycles as a means of work has contributed to the increase in traffic accidents, in particular, mototaxi accidents. The aim of this study was to estimate and characterize the incidence of occupational accidents among the mototaxis registered in Feira de Santana, BA. This is a cross-sectional study with descriptive and census data. Of the 300 professionals registered at the Municipal Transportation Service, 267 professionals were interviewed through a structured questionnaire. Then, a descriptive analysis was conducted and the incidence of accidents was estimated based on the variables studied. Relative risks were calculated and statistical significance was determined using the chi-square test and Fisher's exact test, considering p < 0.05. Logistic regression was used in order to perform simultaneous adjustment of variables. Occupational accidents were observed in 10.5% of mototaxis. There were mainly minor injuries (48.7%), 27% of them requiring leaves of absence from work. There was an association between the days of work per week, fatigue in lower limbs and musculoskeletal complaints, and accidents. Knowledge of the working conditions and accidents involved in this activity can be of great importance for the adoption of traffic education policies, and to help prevent accidents by improving the working conditions and lives of these professionals.

Man, road and vehicle: risk factors associated with the severity of traffic accidents.

PubMed

Almeida, Rosa Lívia Freitas de; Bezerra Filho, José Gomes; Braga, José Ueleres; Magalhães, Francismeire Brasileiro; Macedo, Marinila Calderaro Munguba; Silva, Kellyanne Abreu

2013-08-01

To describe the main characteristics of victims, roads and vehicles involved in traffic accidents and the risk factors involved in accidents resulting in death. METHODS A non-concurrent cohort study of traffic accidents in Fortaleza, CE, Northeastern Brazil, in the period from January 2004 to December 2008. Data from the Fortaleza Traffic Accidents Information System, the Mortality Information System, the Hospital Information System and the State Traffic Department Driving Licenses and Vehicle database. Deterministic and probabilistic relationship techniques were used to integrate the databases. First, descriptive analysis of data relating to people, roads, vehicles and weather was carried out. In the investigation of risk factors for death by traffic accident, generalized linear models were used. The fit of the model was verified by likelihood ratio and ROC analysis. RESULTS There were 118,830 accidents recorded in the period. The most common types of accidents were crashes/collisions (78.1%), running over pedestrians (11.9%), colliding with a fixed obstacle (3.9%), and with motorcycles (18.1%). Deaths occurred in 1.4% of accidents. The factors that were independently associated with death by traffic accident in the final model were bicycles (OR = 21.2, 95%CI 16.1;27.8), running over pedestrians OR = 5.9 (95%CI 3.7;9.2), collision with a fixed obstacle (OR = 5.7, 95%CI 3.1;10.5) and accidents involving motorcyclists (OR = 3.5, 95%CI 2.6;4.6). The main contributing factors were a single person being involved (OR = 6.6, 95%CI 4.1;10.73), presence of unskilled drivers (OR = 4.1, 95%CI 2.9;5.5) a single vehicle (OR = 3.9, 95%CI 2,3;6,4), male (OR = 2.5, 95%CI 1.9;3.3), traffic on roads under federal jurisdiction (OR = 2.4, 95%CI 1.8;3.7), early morning hours (OR = 2.4, 95%CI 1.8;3.0), and Sundays (OR = 1.7, 95%CI 1.3;2.2), adjusted according to the log-binomial model. CONCLUSIONS Activities promoting the prevention of traffic accidents should primarily focus on accidents involving two-wheeled vehicles that most often involves a single person, unskilled, male, at nighttime, on weekends and on roads where they travel at higher speeds.

[Spatial analysis of road traffic accidents with fatalities in Spain, 2008-2011].

PubMed

Gómez-Barroso, Diana; López-Cuadrado, Teresa; Llácer, Alicia; Palmera Suárez, Rocío; Fernández-Cuenca, Rafael

2015-09-01

To estimate the areas of greatest density of road traffic accidents with fatalities at 24 hours per km(2)/year in Spain from 2008 to 2011, using a geographic information system. Accidents were geocodified using the road and kilometer points where they occurred. The average nearest neighbor was calculated to detect possible clusters and to obtain the bandwidth for kernel density estimation. A total of 4775 accidents were analyzed, of which 73.3% occurred on conventional roads. The estimated average distance between accidents was 1,242 meters, and the average expected distance was 10,738 meters. The nearest neighbor index was 0.11, indicating that there were aggregations of accidents in space. A map showing the kernel density was obtained with a resolution of 1 km(2), which identified the areas of highest density. This methodology allowed a better approximation to locating accident risks by taking into account kilometer points. The map shows areas where there was a greater density of accidents. This could be an advantage in decision-making by the relevant authorities. Copyright © 2014 SESPAS. Published by Elsevier Espana. All rights reserved.

Benchmarking MARS (accident management software) with the Browns Ferry fire

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dawson, S.M.; Liu, L.Y.; Raines, J.C.

1992-01-01

The MAAP Accident Response System (MARS) is a userfriendly computer software developed to provide management and engineering staff with the most needed insights, during actual or simulated accidents, of the current and future conditions of the plant based on current plant data and its trends. To demonstrate the reliability of the MARS code in simulatng a plant transient, MARS is being benchmarked with the available reactor pressure vessel (RPV) pressure and level data from the Browns Ferry fire. The MRS software uses the Modular Accident Analysis Program (MAAP) code as its basis to calculate plant response under accident conditions. MARSmore » uses a limited set of plant data to initialize and track the accidnt progression. To perform this benchmark, a simulated set of plant data was constructed based on actual report data containing the information necessary to initialize MARS and keep track of plant system status throughout the accident progression. The initial Browns Ferry fire data were produced by performing a MAAP run to simulate the accident. The remaining accident simulation used actual plant data.« less

Systematic strategies for the third industrial accident prevention plan in Korea.

PubMed

Kang, Young-sig; Yang, Sung-hwan; Kim, Tae-gu; Kim, Day-sung

2012-01-01

To minimize industrial accidents, it's critical to evaluate a firm's priorities for prevention factors and strategies since such evaluation provides decisive information for preventing industrial accidents and maintaining safety management. Therefore, this paper proposes the evaluation of priorities through statistical testing of prevention factors with a cause analysis in a cause and effect model. A priority matrix criterion is proposed to apply the ranking and for the objectivity of questionnaire results. This paper used regression method (RA), exponential smoothing method (ESM), double exponential smoothing method (DESM), autoregressive integrated moving average (ARIMA) model and proposed analytical function method (PAFM) to analyze trends of accident data that will lead to an accurate prediction. This paper standardized the questionnaire results of workers and managers in manufacturing and construction companies with less than 300 employees, located in the central Korean metropolitan areas where fatal accidents have occurred. Finally, a strategy was provided to construct safety management for the third industrial accident prevention plan and a forecasting method for occupational accident rates and fatality rates for occupational accidents per 10,000 people.

General RMP Guidance - Table of Contents

EPA Pesticide Factsheets

The Risk Management Programs for Chemical Accident Prevention (40 CFR Part 68) guidance is in chapters; each covering topics such as applicability of the rule, and requirements for reporting five-year accident history and offsite consequence analysis.

Protecting the AG pilot.

DOT National Transportation Integrated Search

1966-09-01

Summarized data resulting from a detailed review of fatal and non-fatal aerial applicator accidents are presented with an analysis of the factors underlying the accidents. The role of toxic substance is evaluated. Preventive and newer therapeutic app...

A profile of fatal accidents involving alcohol

DOT National Transportation Integrated Search

1977-09-01

Author's abstract: Accident investigation studies were conducted during 1971-75 in the cities of Boston, Baltimore, Oklahoma City and Albuquerque where Alcohol Safety Action Programs (ASAPs) were operating. Analysis of the four studies, plus newly av...

Airway accidents in critical care unit: A 3-year retrospective study in a Public Teaching Hospital of Eastern India

PubMed Central

Dasgupta, Sugata; Singh, Shipti Shradha; Chaudhuri, Arunima; Bhattacharya, Dipasri; Choudhury, Sourav Das

2016-01-01

Background: Although tracheal tubes are essential devices to control and protect airway in a critical care unit (CCU), they are not free from complications. Aims: To document the incidence and nature of airway accidents in the CCU of a government teaching hospital in Eastern India. Methods: Retrospective analysis of all airway accidents in a 5-bedded (medical and surgical) CCU. The number, types, timing, and severity of airway accidents were analyzed. Results: The total accident rate was 19 in 233 intubated and/or tracheostomized patients over 1657 tube days (TDs) during 3 years. Fourteen occurred in 232 endotracheally intubated patients over 1075 endotracheal tube (ETT) days, and five occurred in 44 tracheostomized patients over 580 tracheostomy TDs. Fifteen accidents were due to blocked tubes. Rest four were unplanned extubations (UEs), all being accidental extubations. All blockages occurred during night shifts and all UEs during day shifts. Five accidents were mild, the rest moderate. No major accident led to cardiorespiratory arrest or death. All blockages occurred after 7th day of intubation. The outcome of accidents were more favorable in tracheostomy group compared to ETT group (P = 0.001). Conclusions: The prevalence of airway accidents was 8.2 accidents per 100 patients. Blockages were the most common accidents followed by UEs. Ten out of the 15 blockages and all 4 UEs were in endotracheally intubated patients. Tracheostomized patients had 5 blockages and no UEs. PMID:27076709

Review the number of accidents in Tehran over a two-year period and prediction of the number of events based on a time-series model

PubMed Central

Teymuri, Ghulam Heidar; Sadeghian, Marzieh; Kangavari, Mehdi; Asghari, Mehdi; Madrese, Elham; Abbasinia, Marzieh; Ahmadnezhad, Iman; Gholizadeh, Yavar

2013-01-01

Background: One of the significant dangers that threaten people’s lives is the increased risk of accidents. Annually, more than 1.3 million people die around the world as a result of accidents, and it has been estimated that approximately 300 deaths occur daily due to traffic accidents in the world with more than 50% of that number being people who were not even passengers in the cars. The aim of this study was to examine traffic accidents in Tehran and forecast the number of future accidents using a time-series model. Methods: The study was a cross-sectional study that was conducted in 2011. The sample population was all traffic accidents that caused death and physical injuries in Tehran in 2010 and 2011, as registered in the Tehran Emergency ward. The present study used Minitab 15 software to provide a description of accidents in Tehran for the specified time period as well as those that occurred during April 2012. Results: The results indicated that the average number of daily traffic accidents in Tehran in 2010 was 187 with a standard deviation of 83.6. In 2011, there was an average of 180 daily traffic accidents with a standard deviation of 39.5. One-way analysis of variance indicated that the average number of accidents in the city was different for different months of the year (P < 0.05). Most of the accidents occurred in March, July, August, and September. Thus, more accidents occurred in the summer than in the other seasons. The number of accidents was predicted based on an auto-regressive, moving average (ARMA) for April 2012. The number of accidents displayed a seasonal trend. The prediction of the number of accidents in the city during April of 2012 indicated that a total of 4,459 accidents would occur with mean of 149 accidents per day during these three months. Conclusion: The number of accidents in Tehran displayed a seasonal trend, and the number of accidents was different for different seasons of the year. PMID:26120405

Analysis of accidents in nine Iranian gas refineries: 2007-2011.

PubMed

Mehrdad, R; Bolouri, A; Shakibmanesh, A R

2013-10-01

Occupational accidents are one of the major health hazards in industries and associated with high mortality, morbidity, spiritual damage and economic losses in the world. To determine the incidence of occupational accidents in 9 Iranian gas refineries between March 2007 and February 2011. Data on all occupational accidents occurred between March 2007 and February 2011, as well as other possible associated variables including time of accident, whether the accident was due to a personal or systemic fault, type of accident and its outcomes, age and gender of the victim, the injured parts of the body, job experience, and type of employment, were extracted from HSE reports and notes of health care services. Based on these data, we calculated the incidence rate of accidents and assessed the associated factors. During the 5 studied years, 1129 accidents have been recorded. The incidence of fatal accidents was 1.64 per 100 000 and of nonfatal accidents was 1857 per 100 000 workers per year. 99.4% of injured workers were male. The mean±SD age of injured people was 29.6±7.3 years. Almost 70% of injured workers aged under 30 years. The mean±SD job experience was 5.3±5.3 years. Accidents occurred more commonly around 10:00. More than 60% of accidents happened between 8:00 and 15:00. July had the highest incidence rate. The most common type of accident was being struck by an object (48%). More than 94% of accidents are caused by personal rather than systemic faults. Hands and wrists were the most common injured parts and involved in more than one-third of accidents. 70% of injured workers needed medical treatment and returned to work after primary treatment. The pattern of occupational accidents in Iranian gas refineries is similar to other previous reports in many ways. The incidence did not change significantly over the study period. Establishment of an online network for precise registration, notification and meticulous data collection seems necessary.

Truck Drivers' Experiences and Perspectives Regarding Factors Influencing Traffic Accidents: A Qualitative Study.

PubMed

Karimi Moonaghi, Hossein; Ranjbar, Hossein; Heydari, Abbas; Scurlock-Evans, Laura

2015-08-01

Traffic accidents are a major public health problem, leading to death and disability. Although pertinent studies have been conducted, little data are available in Iran. This study explored the experiences of truck drivers and their perspectives regarding factors contributing to traffic accidents. Eighteen truck drivers, purposively sampled, participated in semi-structured interviews. Data were analyzed using qualitative content analysis. A main theme, lack of ability to control stress, emerged as a factor influencing the incidence of traffic accidents. This main theme was found to have three subthemes: poor organization of the job, lack of workplace facilities and proper equipment, and unsupportive environment. Although several factors were found to contribute to traffic accidents, their effects were not independent, and all were considered significant. Identifying factors that contribute to traffic accidents requires a systematic and holistic approach. Findings could be used by the transportation industry and community health centers to prevent traffic accidents. © 2015 The Author(s).

Longitudinal Trends in Fall Accidents in Community Dwelling Korean Adults: The 2008-2013 Korean Community Health Survey.

PubMed

Hong, Ickpyo; Simpson, Annie N; Logan, Sarah; Woo, Hee-Soon

2016-08-01

To describe the longitudinal characteristics of unintentional fall accidents using a representative population-based sample of Korean adults. We examined data from the Korean Community Health Survey from 2008 to 2013. Univariate analysis and multivariable logistic regression were used to identify the characteristics of fall accidents in adults. Between 2008 and 2013, the incidence rate of fall accidents requiring medical treatment increased from 1,248 to 3,423 per 100,000 people (p<0.001), while the proportion of indoor fall accidents decreased from 38.12% to 23.16% (p<0.001). Females had more annual fall accidents than males (p<0.001). The major reason for fall accidents was slippery floors (33.7% in 2011 and 36.3% in 2013). Between 2008 and 2010, variables associated with higher fall accident risk included specific months (August and September), old age, female gender, current drinker, current smoker, diabetes, osteoarthritis, osteoporosis, and depression. A high level of education and living with a partner were negatively associated with fall accident risk. In 2013, people experiencing more than 1 fall accident felt more fear of falling than those having no fall accidents (odds ratio [OR] for 1 fall, 2.12; 95% confidence interval [CI], 2.04-2.12; OR for more than 2 falls, 2.97; 95% CI, 2.83-3.10). The occurrence of fall accidents has consistently increased in Korea from 2008 to 2013. Future intervention studies are needed to reduce the increasing incidence rates of fall accidents in community dwelling adults.

Longitudinal Trends in Fall Accidents in Community Dwelling Korean Adults: The 2008–2013 Korean Community Health Survey

PubMed Central

Logan, Sarah

2016-01-01

Objective To describe the longitudinal characteristics of unintentional fall accidents using a representative population-based sample of Korean adults. Methods We examined data from the Korean Community Health Survey from 2008 to 2013. Univariate analysis and multivariable logistic regression were used to identify the characteristics of fall accidents in adults. Results Between 2008 and 2013, the incidence rate of fall accidents requiring medical treatment increased from 1,248 to 3,423 per 100,000 people (p<0.001), while the proportion of indoor fall accidents decreased from 38.12% to 23.16% (p<0.001). Females had more annual fall accidents than males (p<0.001). The major reason for fall accidents was slippery floors (33.7% in 2011 and 36.3% in 2013). Between 2008 and 2010, variables associated with higher fall accident risk included specific months (August and September), old age, female gender, current drinker, current smoker, diabetes, osteoarthritis, osteoporosis, and depression. A high level of education and living with a partner were negatively associated with fall accident risk. In 2013, people experiencing more than 1 fall accident felt more fear of falling than those having no fall accidents (odds ratio [OR] for 1 fall, 2.12; 95% confidence interval [CI], 2.04–2.12; OR for more than 2 falls, 2.97; 95% CI, 2.83–3.10). Conclusion The occurrence of fall accidents has consistently increased in Korea from 2008 to 2013. Future intervention studies are needed to reduce the increasing incidence rates of fall accidents in community dwelling adults. PMID:27606272

Risk analysis of urban gas pipeline network based on improved bow-tie model

NASA Astrophysics Data System (ADS)

Hao, M. J.; You, Q. J.; Yue, Z.

2017-11-01

Gas pipeline network is a major hazard source in urban areas. In the event of an accident, there could be grave consequences. In order to understand more clearly the causes and consequences of gas pipeline network accidents, and to develop prevention and mitigation measures, the author puts forward the application of improved bow-tie model to analyze risks of urban gas pipeline network. The improved bow-tie model analyzes accident causes from four aspects: human, materials, environment and management; it also analyzes the consequences from four aspects: casualty, property loss, environment and society. Then it quantifies the causes and consequences. Risk identification, risk analysis, risk assessment, risk control, and risk management will be clearly shown in the model figures. Then it can suggest prevention and mitigation measures accordingly to help reduce accident rate of gas pipeline network. The results show that the whole process of an accident can be visually investigated using the bow-tie model. It can also provide reasons for and predict consequences of an unfortunate event. It is of great significance in order to analyze leakage failure of gas pipeline network.

Usefulness of high resolution coastal models for operational oil spill forecast: the Full City accident

NASA Astrophysics Data System (ADS)

Broström, G.; Carrasco, A.; Hole, L. R.; Dick, S.; Janssen, F.; Mattsson, J.; Berger, S.

2011-06-01

Oil spill modeling is considered to be an important decision support system (DeSS) useful for remedial action in case of accidents, as well as for designing the environmental monitoring system that is frequently set up after major accidents. Many accidents take place in coastal areas implying that low resolution basin scale ocean models is of limited use for predicting the trajectories of an oil spill. In this study, we target the oil spill in connection with the Full City accident on the Norwegian south coast and compare three different oil spill models for the area. The result of the analysis is that all models do a satisfactory job. The "standard" operational model for the area is shown to have severe flaws but including an analysis based on a higher resolution model (1.5 km resolution) for the area the model system show results that compare well with observations. The study also shows that an ensemble using three different models is useful when predicting/analyzing oil spill in coastal areas.

U.S. Civil Rotorcraft Accidents, 1963 Through 1997

NASA Technical Reports Server (NTRS)

Harris, Franklin D.; Kasper, Eugene F.; Iseler, Laura E.

2000-01-01

Narrative summary data produced by the U.S. National Transportation Safety Board (NTSB) has been obtained and analyzed for all 8,436 U.S. civil registered rotorcraft accidents which occurred from mid-1963 through 1997. This analysis was based on the NTSB's assignment of each mishap into one of 21 "first event" categories. The number of U.S. civil registered rotorcraft as recorded by the Federal Aviation Administration (FAA) for the same period has also been obtained. Taken together, these data indicate the civil rotorcraft accident rate (on a per 1,000 registered rotorcraft basis) has decreased by almost a factor of 10 (i.e., from 130 accidents per 1,000 rotorcraft in 1964 to 13.4 per 1,000 in 1997). Analysis of the mishap data indicates over 70% of the rotorcraft accidents were associated with one of the following four NTSB "first event" categories: 2408 Loss of engine power (28.5%); 1,322 In-flight collisions with objects (15.7%); 1,114 Loss of control (13.2%); 1,083 Airframe/component/system failure or malfunction (12.8%).

Comparing the Identification of Recommendations by Different Accident Investigators Using a Common Methodology

NASA Technical Reports Server (NTRS)

Johnson, Chris W.; Oltedal, H. A.; Holloway, C. M.

2012-01-01

Accident reports play a key role in the safety of complex systems. These reports present the recommendations that are intended to help avoid any recurrence of past failures. However, the value of these findings depends upon the causal analysis that helps to identify the reasons why an accident occurred. Various techniques have been developed to help investigators distinguish root causes from contributory factors and contextual information. This paper presents the results from a study into the individual differences that can arise when a group of investigators independently apply the same technique to identify the causes of an accident. This work is important if we are to increase the consistency and coherence of investigations following major accidents.

Offsite Radiological Consequence Analysis for the Bounding Flammable Gas Accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

CARRO, C.A.

2003-07-30

This document quantifies the offsite radiological consequences of the bounding flammable gas accident for comparison with the 25 rem Evaluation Guideline established in DOE-STD-3009, Appendix A. The bounding flammable gas accident is a detonation in a single-shell tank The calculation applies reasonably conservation input parameters in accordance with DOE-STD-3009, Appendix A, guidance. Revision 1 incorporates comments received from Office of River Protection.

[Health care for aged victims of accidents and violence: analysis of SUS health services in Recife (PE, Brazil)].

PubMed

de Lima, Maria Luiza Carvalho; de Souza, Edinilsa Ramos; de Lima, Maria Luiza Lopes Timóteo; Barreira, Alice Kelly; Bezerra, Eduardo Duque; Acioli, Raquel Moura Lins

2010-09-01

A situational diagnosis of the health services regarding the care of aged victims of accidents and violence (AVAV) was carried out in Recife, Pernambuco, Brazil. The National Policy for Reducing Accident and Violence Related Morbidity and Mortality and the National Policy for the Aged People Health were used as references. The methodology was based on the triangulation method, with both quantitative and qualitative approaches. Questionnaires and interviews were answered by managers and health staff of hospital, prehospital and rehabilitation services; and local aged health policy managers. In 2006, only the Family Health Program reported prehospital care for AVAV, 31 cases were due to violence and 18 to accidents. The hospital care for aged people was 7.2% of the total care, 27% from accidents and 10% from violence. In the same year, there was no record of rehabilitation care of AVAV. The directives of the policies studied are only partially followed. The health care is deficient in several aspects, such as: clinical protocols; notification devices; support to the aged, caregivers and aggressors; and also continuous training. This analysis can be such a contribution to the reorganization of the local health system, recognizing the aged person as vulnerable to accidents and violence.

Safety training priorities

NASA Astrophysics Data System (ADS)

Thompson, N. A.; Ruck, H. W.

1984-04-01

The Air Force is interested in identifying potentially hazardous tasks and prevention of accidents. This effort proposes four methods for determining safety training priorities for job tasks in three enlisted specialties. These methods can be used to design training aimed at avoiding loss of people, time, materials, and money associated with on-the-job accidents. Job tasks performed by airmen were measured using task and job factor ratings. Combining accident reports and job inventories, subject-matter experts identified tasks associated with accidents over a 3-year period. Applying correlational, multiple regression, and cost-benefit analysis, four methods were developed for ordering hazardous tasks to determine safety training priorities.

Effects of Security actions

NASA Astrophysics Data System (ADS)

Bergman, Ramona; Andersson-Sköld, Yvonne; Nyberg, Lars; Johansson, Magnus

2010-05-01

In a project funded by the Swedish Civil Contingencies Agency, the effort and work to reduce different kinds of accidents are being evaluated. The project wants to illuminate the links between actions and outcome, so we can learn from today's performance and in the future select more effective measures and overall deal with accidents more efficiently. The project ESS covers the field of frequent accidents such as sliding accidents at home, in house fires and less common accidents such as chemical and land fill accidents up to even more rare accidents such as natural accidents and hazards. In the ESS project SGI (Swedish geotechnical institute) will evaluate the work and effort concerning various natural hazards limited to landslides, erosion and flooding. The aim is to investigate how municipalities handle, especially prevention, of such natural disasters today. The project includes several aspects such as: • which are the driving forces for risk analysis in a municipality • do one use risk mapping (and what type) in municipal risk analysis • which aspects are most important when selecting preventive measures • in which way do one learn from past accidents • and from previous accidents elsewhere, by for example use existing databases • etc There are many aspects that play a role in a well-functioning safety promotion work. The overall goal is to examine present work and activities, highlight what is well functioning and identify weak points. The aim is to find out where more resources are needed and give suggestions for a more efficient security work. This includes identification of the most efficient "tools" in use or needed. Such tools can be education, directives, funding, more easily available maps and information regarding previous accidents and preventive measures etc. The project will result in recommendations for more effective ways to deal with landslides, erosion and flooding. Since different kinds of problems can occur depending on level of authority the investigation of the security work will be done with authorities on both regional and local scale. At the moment the investigation process are in progress and preliminary results will be presented.

Loss of Coolant Accident (LOCA) / Emergency Core Coolant System (ECCS Evaluation of Risk-Informed Margins Management Strategies for a Representative Pressurized Water Reactor (PWR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szilard, Ronaldo Henriques

A Risk Informed Safety Margin Characterization (RISMC) toolkit and methodology are proposed for investigating nuclear power plant core, fuels design and safety analysis, including postulated Loss-of-Coolant Accident (LOCA) analysis. This toolkit, under an integrated evaluation model framework, is name LOCA toolkit for the US (LOTUS). This demonstration includes coupled analysis of core design, fuel design, thermal hydraulics and systems analysis, using advanced risk analysis tools and methods to investigate a wide range of results.

An Exercise Health Simulation Method Based on Integrated Human Thermophysiological Model

PubMed Central

Chen, Xiaohui; Yu, Liang; Yang, Kaixing

2017-01-01

Research of healthy exercise has garnered a keen research for the past few years. It is known that participation in a regular exercise program can help improve various aspects of cardiovascular function and reduce the risk of suffering from illness. But some exercise accidents like dehydration, exertional heatstroke, and even sudden death need to be brought to attention. If these exercise accidents can be analyzed and predicted before they happened, it will be beneficial to alleviate or avoid disease or mortality. To achieve this objective, an exercise health simulation approach is proposed, in which an integrated human thermophysiological model consisting of human thermal regulation model and a nonlinear heart rate regulation model is reported. The human thermoregulatory mechanism as well as the heart rate response mechanism during exercise can be simulated. On the basis of the simulated physiological indicators, a fuzzy finite state machine is constructed to obtain the possible health transition sequence and predict the exercise health status. The experiment results show that our integrated exercise thermophysiological model can numerically simulate the thermal and physiological processes of the human body during exercise and the predicted exercise health transition sequence from finite state machine can be used in healthcare. PMID:28702074

Dynamic safety assessment of natural gas stations using Bayesian network.

PubMed

Zarei, Esmaeil; Azadeh, Ali; Khakzad, Nima; Aliabadi, Mostafa Mirzaei; Mohammadfam, Iraj

2017-01-05

Pipelines are one of the most popular and effective ways of transporting hazardous materials, especially natural gas. However, the rapid development of gas pipelines and stations in urban areas has introduced a serious threat to public safety and assets. Although different methods have been developed for risk analysis of gas transportation systems, a comprehensive methodology for risk analysis is still lacking, especially in natural gas stations. The present work is aimed at developing a dynamic and comprehensive quantitative risk analysis (DCQRA) approach for accident scenario and risk modeling of natural gas stations. In this approach, a FMEA is used for hazard analysis while a Bow-tie diagram and Bayesian network are employed to model the worst-case accident scenario and to assess the risks. The results have indicated that the failure of the regulator system was the worst-case accident scenario with the human error as the most contributing factor. Thus, in risk management plan of natural gas stations, priority should be given to the most probable root events and main contribution factors, which have identified in the present study, in order to reduce the occurrence probability of the accident scenarios and thus alleviate the risks. Copyright © 2016 Elsevier B.V. All rights reserved.

Fuzzy Bayesian Network-Bow-Tie Analysis of Gas Leakage during Biomass Gasification

PubMed Central

Yan, Fang; Xu, Kaili; Yao, Xiwen; Li, Yang

2016-01-01

Biomass gasification technology has been rapidly developed recently. But fire and poisoning accidents caused by gas leakage restrict the development and promotion of biomass gasification. Therefore, probabilistic safety assessment (PSA) is necessary for biomass gasification system. Subsequently, Bayesian network-bow-tie (BN-bow-tie) analysis was proposed by mapping bow-tie analysis into Bayesian network (BN). Causes of gas leakage and the accidents triggered by gas leakage can be obtained by bow-tie analysis, and BN was used to confirm the critical nodes of accidents by introducing corresponding three importance measures. Meanwhile, certain occurrence probability of failure was needed in PSA. In view of the insufficient failure data of biomass gasification, the occurrence probability of failure which cannot be obtained from standard reliability data sources was confirmed by fuzzy methods based on expert judgment. An improved approach considered expert weighting to aggregate fuzzy numbers included triangular and trapezoidal numbers was proposed, and the occurrence probability of failure was obtained. Finally, safety measures were indicated based on the obtained critical nodes. The theoretical occurrence probabilities in one year of gas leakage and the accidents caused by it were reduced to 1/10.3 of the original values by these safety measures. PMID:27463975

Rail-highway crossing accident prediction analysis

DOT National Transportation Integrated Search

1987-04-01

This report contains technical results that have been produced in a study : to revise and update the DOT rail-highway crossing resource allocation : procedure. This work has resulted in new accident prediction and severity : formulas, a modified and ...

Statistical Estimation of Rollover Risk

DOT National Transportation Integrated Search

1989-08-01

This report describes the results of a statistical analysis to determine the : probability of a rollover in a single vehicle accident. Over 39,000 accidents, : which included 4910 rollovers in the states of Texas, Maryland, and Washington were : exam...

Data mining and visualization of the Alabama accident database

DOT National Transportation Integrated Search

2000-08-01

The Alabama Department of Public Safety has developed and maintains a centralized database that contain traffic accident data collected from crash report completed by local police officers and state troopers. The Critical Analysis Reporting Environme...

Yellow taxis have fewer accidents than blue taxis because yellow is more visible than blue

PubMed Central

Ho, Teck-Hua; Chong, Juin Kuan; Xia, Xiaoyu

2017-01-01

Is there a link between the color of a taxi and how many accidents it has? An analysis of 36 mo of detailed taxi, driver, and accident data (comprising millions of data points) from the largest taxi company in Singapore suggests that there is an explicit link. Yellow taxis had 6.1 fewer accidents per 1,000 taxis per month than blue taxis, a 9% reduction in accident probability. We rule out driver difference as an explanatory variable and empirically show that because yellow taxis are more noticeable than blue taxis—especially when in front of another vehicle, and in street lighting—other drivers can better avoid hitting them, directly reducing the accident rate. This finding can play a significant role when choosing colors for public transportation and may save lives as well as millions of dollars. PMID:28265081

Yellow taxis have fewer accidents than blue taxis because yellow is more visible than blue.

PubMed

Ho, Teck-Hua; Chong, Juin Kuan; Xia, Xiaoyu

2017-03-21

Is there a link between the color of a taxi and how many accidents it has? An analysis of 36 mo of detailed taxi, driver, and accident data (comprising millions of data points) from the largest taxi company in Singapore suggests that there is an explicit link. Yellow taxis had 6.1 fewer accidents per 1,000 taxis per month than blue taxis, a 9% reduction in accident probability. We rule out driver difference as an explanatory variable and empirically show that because yellow taxis are more noticeable than blue taxis-especially when in front of another vehicle, and in street lighting-other drivers can better avoid hitting them, directly reducing the accident rate. This finding can play a significant role when choosing colors for public transportation and may save lives as well as millions of dollars.

The practical application of mishap data in Army aircraft system safety programs

NASA Technical Reports Server (NTRS)

Darrah, J. T., Jr.

1971-01-01

The means are discussed by which the the United States Army Board for Aviation Accident Research (USABAAR) now utilizes the vast store of historical accident data in the application of the system safety concept for developmental aircraft. USABAAR serves as the central agency for the Army Accident Prevention Program which includes the receipt, processing, and analysis of all data and information related to Army aircraft accident experience. It is pointed out that methods which served the cause of accident prevention so well in the past are no longer adequate and that traditional parameters used to measure mishap experience have become obsolete. USABAAR has developed, and recently put into use, completely revised accident reporting forms which greatly expand the scope and detail of information provided as a result of investigation. This and other factors which have resulted in an improved data system are discussed in detail.

A synthesis of studies of access point density as a risk factor for road accidents.

PubMed

Elvik, Rune

2017-10-01

Studies of the relationship between access point density (number of access points, or driveways, per kilometre of road) and accident frequency or rate (number of accidents per unit of exposure) have consistently found that accident rate increases when access point density increases. This paper presents a formal synthesis of the findings of these studies. It was found that the addition of one access point per kilometre of road is associated with an increase of 4% in the expected number of accidents, controlling for traffic volume. Although studies consistently indicate an increase in accident rate as access point density increases, the size of the increase varies substantially between studies. In addition to reviewing studies of access point density as a risk factor, the paper discusses some issues related to formally synthesising regression coefficients by applying the inverse-variance method of meta-analysis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Contribution of Raman and Surface Enhanced Raman Spectroscopy (SERS) to the analysis of vehicle headlights: Dye(s) characterization.

PubMed

Muehlethaler, Cyril; Cheng, Yin Pak; Islam, Syed K; Lombardi, John R

2018-06-01

Although ubiquitous on accident scenes, the polymers from headlight optics are often neglected in hit-and-run cases, and their evidential value restrained to direct comparison once a corresponding vehicle is found. Multilayered automotive paint fragments are preferred for their access to corresponding databases (PDQ, EUCAP) to infer models and brands of cars. The potential of polymers headlights for providing forensic intelligence has never been exploited, principally due to the lack of diversity, of appropriate databases, and of case examples. The motives are very simple however. Headlight polymers suffer from a lack of differentiation, and about 90% of them are composed of polymethylmethacrylate (PMMA). The discriminating powers using techniques in sequence typically range from 30 to 60%. In this paper, we take advantage of the extreme sensitivity of Surface Enhanced Raman Spectroscopy (SERS) to analyze the dye composition of the polymer headlights. The measurements by standard Raman spectroscopy at 488, 633, and 785nm permits us to identify the polymer type with relative ease. 51 out of 53 samples are composed of PMMA, the two remaining being either Polycarbonate or Polybutylene terephthalate. Additionally, using SERS with silver colloids at 488 and 633nm, provides enhanced spectra of the dyes used in the composition with an extreme sensitivity and specificity. With SERS we are able to differentiate the majority of the headlights with a remarkable 90-100% discriminating power. Solvent Orange 60, Solvent Red 52 and Solvent Red 111 were successfully identified as dyes used in the manufacture of the headlights. These results demonstrate that a combined Raman-SERS approach has the potential to replace an otherwise lengthy sequence of many different analytical techniques. With one single instrument, we offer the possibility to combine an analysis of the polymer type, and of the dye components with high discriminating capabilities. These results open up new opportunities for exploiting headlight plastics in road accidents investigations. It has the potential to help in source attribution, and/or database building in a forensic intelligence perspective. Copyright © 2018 Elsevier B.V. All rights reserved.

Anthropotechnological analysis of industrial accidents in Brazil.

PubMed Central

Binder, M. C.; de Almeida, I. M.; Monteau, M.

1999-01-01

The Brazilian Ministry of Labour has been attempting to modify the norms used to analyse industrial accidents in the country. For this purpose, in 1994 it tried to make compulsory use of the causal tree approach to accident analysis, an approach developed in France during the 1970s, without having previously determined whether it is suitable for use under the industrial safety conditions that prevail in most Brazilian firms. In addition, opposition from Brazilian employers has blocked the proposed changes to the norms. The present study employed anthropotechnology to analyse experimental application of the causal tree method to work-related accidents in industrial firms in the region of Botucatu, São Paulo. Three work-related accidents were examined in three industrial firms representative of local, national and multinational companies. On the basis of the accidents analysed in this study, the rationale for the use of the causal tree method in Brazil can be summarized for each type of firm as follows: the method is redundant if there is a predominance of the type of risk whose elimination or neutralization requires adoption of conventional industrial safety measures (firm representative of local enterprises); the method is worth while if the company's specific technical risks have already largely been eliminated (firm representative of national enterprises); and the method is particularly appropriate if the firm has a good safety record and the causes of accidents are primarily related to industrial organization and management (multinational enterprise). PMID:10680249

[Epidemiological characteristics and types of domestic and leisure accidents: sentinel health network of Castilla y León (2009)].

PubMed

Mateos Baruque, María Loreto; Vián González, Eva María; Gil Costa, Milagros; Lozano Alonso, José Eugenio; Santamaría Rodrigo, Elena; Herrero Cembellín, Belén

2012-05-01

To study incidence, epidemiological characteristics and types of domestic and leisure accidents in Castilla y León during 2009. A descriptive study using a prospective sample design. Health Primary Care Centres of Castilla y León. The Nurse Registry is made up of 130 nurses selected by conglomerates analysis. They cover 5% of the population. The information was obtained by means of an anonymous form. The studied variables were sex, age, type, place, type and origin of the accident. A descriptive analysis was performed using χ(2), Fischer, χ(2) of trends and t Student tests, with 95% confidence intervals. The annual cumulative incidence was 2651 cases/100000 inhabitants, there being slightly higher percentage of men (50.4%). The ≤ 15 and ≥ 65 years age groups had more accidents. The time of day of 49.2% of the accidents was during the morning and 71.7% were on a working day. The majority (57.1%) took place in the home, 16,8% in the street, and 7.3% in schools. The most common accidents types were falls to the same level (40.4%) and use of cutting and sharp objects (22.7%). Most accidents took place within the home, on a working day and by falls. The most affected were the ≤ 15 and ≥ 65 years old age groups. Copyright © 2010 Elsevier España, S.L. All rights reserved.

An investigation on fatality of drivers in vehicle-fixed object accidents on expressways in China: Using multinomial logistic regression model.

PubMed

Peng, Yong; Peng, Shuangling; Wang, Xinghua; Tan, Shiyang

2018-06-01

This study aims to identify the effects of characteristics of vehicle, roadway, driver, and environment on fatality of drivers in vehicle-fixed object accidents on expressways in Changsha-Zhuzhou-Xiangtan district of Hunan province in China by developing multinomial logistic regression models. For this purpose, 121 vehicle-fixed object accidents from 2011-2017 are included in the modeling process. First, descriptive statistical analysis is made to understand the main characteristics of the vehicle-fixed object crashes. Then, 19 explanatory variables are selected, and correlation analysis of each two variables is conducted to choose the variables to be concluded. Finally, five multinomial logistic regression models including different independent variables are compared, and the model with best fitting and prediction capability is chosen as the final model. The results showed that the turning direction in avoiding fixed objects raised the possibility that drivers would die. About 64% of drivers died in the accident were found being ejected out of the car, of which 50% did not use a seatbelt before the fatal accidents. Drivers are likely to die when they encounter bad weather on the expressway. Drivers with less than 10 years of driving experience are more likely to die in these accidents. Fatigue or distracted driving is also a significant factor in fatality of drivers. Findings from this research provide an insight into reducing fatality of drivers in vehicle-fixed object accidents.

Parametric and experimentally informed BWR Severe Accident Analysis Utilizing FeCrAl - M3FT-17OR020205041

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ott, Larry J.; Howell, Michael; Robb, Kevin R.

Iron-chromium-aluminum (FeCrAl) alloys are being considered as advanced fuel cladding concepts with enhanced accident tolerance. At high temperatures, FeCrAl alloys have slower oxidation kinetics and higher strength compared with zirconium-based alloys. FeCrAl could be used for fuel cladding and spacer or mixing vane grids in light water reactors and/or as channel box material in boiling water reactors (BWRs). There is a need to assess the potential gains afforded by the FeCrAl accident-tolerant-fuel (ATF) concept over the existing zirconium-based materials employed today. To accurately assess the response of FeCrAl alloys under severe accident conditions, a number of FeCrAl properties and characteristicsmore » are required. These include thermophysical properties as well as burst characteristics, oxidation kinetics, possible eutectic interactions, and failure temperatures. These properties can vary among different FeCrAl alloys. Oak Ridge National Laboratory has pursued refined values for the oxidation kinetics of the B136Y FeCrAl alloy (Fe-13Cr-6Al wt %). This investigation included oxidation tests with varying heating rates and end-point temperatures in a steam environment. The rate constant for the low-temperature oxidation kinetics was found to be higher than that for the commercial APMT FeCrAl alloy (Fe-21Cr-5Al-3Mo wt %). Compared with APMT, a 5 times higher rate constant best predicted the entire dataset (root mean square deviation). Based on tests following heating rates comparable with those the cladding would experience during a station blackout, the transition to higher oxidation kinetics occurs at approximately 1,500°C. A parametric study varying the low-temperature FeCrAl oxidation kinetics was conducted for a BWR plant using FeCrAl fuel cladding and channel boxes using the MELCOR code. A range of station blackout severe accident scenarios were simulated for a BWR/4 reactor with Mark I containment. Increasing the FeCrAl low-temperature oxidation rate constant (3 times and 10 times that of the rate constant for APMT) had a negligible impact on the early stages of the accident and minor impacts on the accident progression after the first relocation of the fuel. At temperatures below 1,500°C, increasing the rate constant for APMT by a factor of 10 still resulted in only minor FeCrAl oxidation. In general, the gains afforded by the FeCrAl enhanced ATF concept with respect to accident sequence timing and combustible gas generation are consistent with previous efforts. Compared with the traditional Zircaloy-based cladding and channel box system, the FeCrAl concept could provide a few extra hours of time for operators to take mitigating actions and/or for evacuations to take place. A coolable core geometry is retained longer, enhancing the ability to stabilize an accident. For example, a station blackout was simulated in which cooling water injection was lost 36 hours after shutdown. The timing to first fuel relocation was delayed by approximately 5 h for the FeCrAl ATF concept compared with that of the traditional Zircaloy-based cladding and channel box system.« less

Analysis of stationary and dynamic factors affecting highway accident occurrence: A dynamic correlated grouped random parameters binary logit approach.

PubMed

Fountas, Grigorios; Sarwar, Md Tawfiq; Anastasopoulos, Panagiotis Ch; Blatt, Alan; Majka, Kevin

2018-04-01

Traditional accident analysis typically explores non-time-varying (stationary) factors that affect accident occurrence on roadway segments. However, the impact of time-varying (dynamic) factors is not thoroughly investigated. This paper seeks to simultaneously identify pre-crash stationary and dynamic factors of accident occurrence, while accounting for unobserved heterogeneity. Using highly disaggregate information for the potential dynamic factors, and aggregate data for the traditional stationary elements, a dynamic binary random parameters (mixed) logit framework is employed. With this approach, the dynamic nature of weather-related, and driving- and pavement-condition information is jointly investigated with traditional roadway geometric and traffic characteristics. To additionally account for the combined effect of the dynamic and stationary factors on the accident occurrence, the developed random parameters logit framework allows for possible correlations among the random parameters. The analysis is based on crash and non-crash observations between 2011 and 2013, drawn from urban and rural highway segments in the state of Washington. The findings show that the proposed methodological framework can account for both stationary and dynamic factors affecting accident occurrence probabilities, for panel effects, for unobserved heterogeneity through the use of random parameters, and for possible correlation among the latter. The comparative evaluation among the correlated grouped random parameters, the uncorrelated random parameters logit models, and their fixed parameters logit counterpart, demonstrate the potential of the random parameters modeling, in general, and the benefits of the correlated grouped random parameters approach, specifically, in terms of statistical fit and explanatory power. Published by Elsevier Ltd.

Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015

PubMed Central

Mehmandar, Mohammadreza; Soori, Hamid; Mehrabi, Yadolah

2016-01-01

Background: Predicting the trend in traffic accidents deaths and its analysis can be a useful tool for planning and policy-making, conducting interventions appropriate with death trend, and taking the necessary actions required for controlling and preventing future occurrences. Objective: Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015. Settings and Design: It was a cross-sectional study. Materials and Methods: All the information related to fatal traffic accidents available in the database of Iran Legal Medicine Organization from 2004 to the end of 2013 were used to determine the change points (multi-variable time series analysis). Using autoregressive integrated moving average (ARIMA) model, traffic accidents death rates were predicted for 2014 and 2015, and a comparison was made between this rate and the predicted value in order to determine the efficiency of the model. Results: From the results, the actual death rate in 2014 was almost similar to that recorded for this year, while in 2015 there was a decrease compared with the previous year (2014) for all the months. A maximum value of 41% was also predicted for the months of January and February, 2015. Conclusion: From the prediction and analysis of the death trends, proper application and continuous use of the intervention conducted in the previous years for road safety improvement, motor vehicle safety improvement, particularly training and culture-fostering interventions, as well as approval and execution of deterrent regulations for changing the organizational behaviors, can significantly decrease the loss caused by traffic accidents. PMID:27308255

Maritime Transportation Risk Assessment of Tianjin Port with Bayesian Belief Networks.

PubMed

Zhang, Jinfen; Teixeira, Ângelo P; Guedes Soares, C; Yan, Xinping; Liu, Kezhong

2016-06-01

This article develops a Bayesian belief network model for the prediction of accident consequences in the Tianjin port. The study starts with a statistical analysis of historical accident data of six years from 2008 to 2013. Then a Bayesian belief network is constructed to express the dependencies between the indicator variables and accident consequences. The statistics and expert knowledge are synthesized in the Bayesian belief network model to obtain the probability distribution of the consequences. By a sensitivity analysis, several indicator variables that have influence on the consequences are identified, including navigational area, ship type and time of the day. The results indicate that the consequences are most sensitive to the position where the accidents occurred, followed by time of day and ship length. The results also reflect that the navigational risk of the Tianjin port is at the acceptable level, despite that there is more room of improvement. These results can be used by the Maritime Safety Administration to take effective measures to enhance maritime safety in the Tianjin port. © 2016 Society for Risk Analysis.

[The cases of accident in the ceramic tile industry in relation to the age and job seniority of the workers].

PubMed

Candela, S; Duca, P; Bedogni, L

1993-01-01

A study was made of 3,368 workers in 36 ceramic plants in the Scandiano area (Reggio Emilia, Italy) during the year 1990; 403 had an accident during the observation period. The incidence and severity of the accident were correlated to age, job (low, intermediate, high accident risk), duration of employment as at 1.1.1990 (> 24, 12-24, > 24, 12-24, < 12 months, engaged during 1990). Logistic regression analysis, survival analysis and RIDIT analysis were performed using GLIM and EGRET statistical packages. Risk: ORs for intermediate and high-risk jobs vs low-risk jobs were 1.3 (1.0-1.7 95% confidence limits) and 1.7 (1.3-2.3), respectively, adjusted for duration of employment; ORs for the 12-24, < 12 months, engaged during 1990 categories vs the > 24 months category were 1.5 (1.1-2.0), 1.7 (1.3-2.2), 2.1 (1.6-2.8) respectively. Severity: the mean RIDIT of the > 44-year-old vs < 30-year-old workers was 0.6 (0.53-0.67).

[The topical problems of the car accident injury emerging from the materials of the articles published in the journal "Sudebno-meditsinskaya ekspertiza" during the period from 1958 to 2012].

PubMed

Fetisov, V A; Smirenin, S A; Nesterov, A V; Khabova, Z S

2014-01-01

The authors undertook the scientometric analysis of the articles published in the journal "Sudebno-meditsinskaya ekspertiza" during the last 55 years (from 1958 to 2012) with special reference to the information support of research and practical activities of forensic medical experts in this country concerning the topical problems of the car accident injury. The search for relevant information revealed a total of 111 articles that were categorized into several groups for their further systematization and analysis with the view for improving the effectiveness of research and experimental studies in the framework of the principal activities of the State Sanitary and Epidemiological Department of the Russian Federation. This article is an extension of previous publications of the authors concerning the main aspects of the car accident injury. The forthcoming reports to be published in the journal "Sudebno-meditsinskaya ekspertiza" will present the results of the further in-depth scientometric analysis of the data on road accidents in this country.

Paralysis from sport and diving accidents.

PubMed

Schmitt, H; Gerner, H J

2001-01-01

To examine the causes of sport-related spinal cord injuries that developed into paraplegia or tetraplegia, and to compare data from different sports with previous studies in the same geographical region. A retrospective epidemiological study and comparison with previous studies. The Orthopedic Department, specializing in the treatment and rehabilitation of paralyzed patients, at the University of Heidelberg, Germany. Between 1985 and 1997, 1,016 cases of traumatic spinal cord injury presented at the Orthopedic Department at the University of Heidelberg: 6.8% were caused by sport and 7.7% by diving accidents. Sport-related spinal cord injuries with paralysis. A total of 1.016 cases of traumatic spinal cord injury were reviewed. Of these, 14.5% were caused by sport accidents (n = 69) or diving accidents (n = 78). Age of patients ranged from 9 to 52 years. 83% were male. 77% of the patients developed tetraplegia, and 23%, paraplegia. 16 of the sport accidents resulted from downhill skiing, 9 resulted from horseback riding, 7 from modern air sports, 6 from gymnastics, 5 from trampolining, and 26 from other sports. Previous analyses had revealed that paraplegia had mainly occurred from gymnastics, trampolining, or high diving accidents. More recently, however, the number of serious spinal injuries caused by risk-filled sports such as hang gliding and paragliding has significantly increased (p = 0.095), as it has for horseback riding and skiing. Examinations have shown that all patients who were involved in diving accidents developed tetraplegia. An analysis of injury from specific sports is still under way. Analysis of accidents resulting in damage to the spinal cord in respect to different sports shows that sports that have become popular during the last 10 years show an increasing risk of injury. Modern air sports hold the most injuries. Injury-preventing strategies also are presented.

The association between attributions of responsibility for motor vehicle accidents and patient satisfaction: a study within a no-fault injury compensation system.

PubMed

Thompson, Jason; Berk, Michael; O'Donnell, Meaghan; Stafford, Lesley; Nordfjaern, Trond

2015-05-01

This study set out to test the relationship between attributions of responsibility for motor vehicle accidents and satisfaction with personal injury compensation systems. The study analysed survey data from 1394 people injured in a motor vehicle accident who were compensated under a no-fault personal injury compensation system. Patients' ratings of satisfaction with the compensation system across five domains (resolves your issues, keeps you up-to-date, treats you as an individual, cares about you, and overall satisfaction) were analysed alongside patient attributions of responsibility for their accident (not responsible, partly responsible, totally responsible). Postaccident physical and mental health status, age, gender, and duration of compensation claim were controlled for in the analysis. A multivariate analysis of covariance indicated attributions of responsibility for accidents were significantly associated with levels of patient satisfaction across all five domains under study (F (10, 2084) = 3.7, p<0.001, η(2)  =0.02). Despite access to virtually indistinguishable services, patients who attributed responsibility for their accidents to others were significantly less satisfied with the injury compensation system than those who attributed responsibility to themselves. Satisfaction with no-fault motor vehicle injury compensation services are associated with patients' attributions of responsibility for their accident. Compensation systems and other rehabilitation services monitoring patient satisfaction should adjust for attributions of responsibility when assessing levels of patient satisfaction between time periods, services, or injured populations. Differences in levels of patient satisfaction observed between compensation or rehabilitation populations may reflect differences in attributions of responsibility for accidents rather than objective service quality. © The Author(s) 2014.

The potential risk of toxoplasmosis for traffic accidents: A systematic review and meta-analysis.

PubMed

Gohardehi, Shaban; Sharif, Mehdi; Sarvi, Shahabeddin; Moosazadeh, Mahmood; Alizadeh-Navaei, Reza; Hosseini, Seyed Abdollah; Amouei, Afsaneh; Pagheh, Abdolsattar; Sadeghi, Mitra; Daryani, Ahmad

2018-06-12

Toxoplasmosis is a prevalent infectious disease. Although most people infected by Toxoplasma gondii are asymptomatic, evidence has suggested that this disease might affect some aspects of a host's behavior and associate with schizophrenia, suicide attempt, changes in various aspects of personality, and poor neurocognitive performance. These associations may play roles in increasing the risk of a number of incidents, such as traffic accidents, among infected people. In this regard, this study aimed to provide summary estimates for the available data on the potential risk of toxoplasmosis for traffic accidents. To this end, using a number of search terms, i.e. toxoplasmosis, Toxoplasma gondii, traffic accident, road accident, car accident, crash, and prevalence, literature searches (up to October 1, 2017) were carried out via 6 databases. The meta-analysis was conducted using the StatsDirect statistical software and a P-value less than 0.05 was regarded as significant in all statistical analyses. Out of 1841 identified studies, 9 studies were finally considered eligible for carrying out this systematic review. Reviewing results of these studies indicated that 5 out of 9 studies reported a significant relationship between Toxoplasma gondii and traffic accidents. Additionally, data related to gender showed significant differences between infected and control men and women. Considering age, reviewing the results of these studies revealed a significant difference between the infected people and the Toxoplasma-negative subjects under 45 years of age. However, no significant difference was found between the two groups aged 45 or older. Given these results, it can be concluded that Toxoplasma gondii significantly increases the risk of having traffic accidents. Copyright © 2018 Elsevier Inc. All rights reserved.

Psychosocial identification of drivers responsible for fatal vehicular accidents in Boston

DOT National Transportation Integrated Search

1976-05-01

This Final Report includes a total human factor data presentation, analysis, evaluation and interpretation of selected variables collected by the Boston University Traffic Accident Research Special Study team during the 30-month period of the experim...

An analysis of truck size and weight : phase I - safety.

DOT National Transportation Integrated Search

2013-11-01

Commercial motor vehicles carrying heavier loads or employing multiple trailers present significant concerns regarding the impact of their use in terms of increased accidents, accident severity and fatalities. In 2011, the most recent year for which ...

Analysis and testing of Koornstra-type induced exposure models

DOT National Transportation Integrated Search

1985-10-01

Induced exposure models postulate a structure for accident data which permits the : estimation of two factors: exposure and proneness. Since information on exposure : is needed in order to assess the accident risk of different driver, vehicle, and : ...

Aircraft accidents by older persons.

DOT National Transportation Integrated Search

1967-10-01

During 1965 there were 450,494 certificated general aviation pilots in the United States, of which 9,826 were over sixty years old. Within this group there were 108 accidents, 17 of which were fatal. Statistical analysis (chi square) revealed that th...

Terror attacks influence driving behavior in Israel

PubMed Central

Stecklov, Guy; Goldstein, Joshua R.

2004-01-01

Terror attacks in Israel produce a temporary lull in light accidents followed by a 35% spike in fatal accidents on Israeli roads 3 days after the attack. Our results are based on time-series analysis of Israeli traffic flows, accidents, and terror attacks from January 2001 through June 2002. Whereas prior studies have focused on subjective reports of posttraumatic stress, our study shows a population-level behavioral response to violent terror attacks. PMID:15448203

Assessing accident phobia in mild traumatic brain injury: The Accident Fear Questionnaire.

PubMed

Sutherland, Jessica; Middleton, Jason; Ornstein, Tisha J; Lawson, Kerry; Vickers, Kristin

2016-08-01

Despite a documented prevalence of accident phobia in almost 40% of motor vehicle accident (MVA) survivors, the onset of accident phobia after traumatic brain injury (TBI) remains poorly understood. There is currently a body of knowledge about posttraumatic stress disorder (PTSD) in patients with TBI, but less is known about accident phobia following TBI, particularly in cases of mild TBI (mTBI). Accident phobia can impede safe return to driving or motor vehicle travel, inhibiting return to daily functioning. In addition, pain complaints have been found to correlate positively with postinjury anxiety disorders. The present study sought to determine the reliability and validity of the Accident Fear Questionnaire (AFQ), a measure used to assess accident phobia, in 72 patients with mTBI using secondary data analysis and the subsequent development of accident phobia postinjury. Furthermore, we sought to examine the impact of pain, anxiety, and depression complaints on the AFQ. Results reveal convergent validity and reliability in mTBI populations. Additionally, pain, anxiety, and depression measures were significantly correlated with scores on the AFQ. Psychometrically, the phobia avoidance subscale of the AFQ is a reliable measure for use with mTBI populations, although some limitations were found. In particular, the accident profile (AP) subscale was not found to be reliable or valid and could be eliminated from the AFQ. Collectively, the present study contributes to the small body of published literature evaluating accident phobia in patients with mTBI and the impact of pain on the development of postinjury anxiety disorders. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

A Policy Intervention Study to Identify High-Risk Groups to Prevent Industrial Accidents in Republic of Korea.

PubMed

Yi, Kwan Hyung; Lee, Seung Soo

2016-09-01

The objective of this study is to identify high-risk groups for industrial accidents by setting up 2003 as the base year and conducting an in-depth analysis of the trends of major industrial accident indexes the index of industrial accident rate, the index of occupational injury rate, the index of occupational illness and disease rate per 10,000 people, and the index of occupational injury fatality rate per 10,000 people for the past 10 years. This study selected industrial accident victims, who died or received more than 4 days of medical care benefits, due to occupational accidents and diseases occurring at workplaces, subject to the Industrial Accident Compensation Insurance Act, as the study population. According to the trends of four major indexes by workplace characteristics, the whole industry has shown a decreasing tendency in all four major indexes since the base year (2003); as of 2012, the index of industrial accident rate was 67, while the index of occupational injury fatality rate per 10,000 people was 59. The manufacturing industry, age over 50 years and workplaces with more than 50 employees showed a high severity level of occupational accidents. Male workers showed a higher severity level of occupational accidents than female workers. The employment period of < 3 years and newly hired workers with a relatively shorter working period are likely to have more occupational accidents than others. Overall, an industrial accident prevention policy must be established by concentrating all available resources and capacities of these high-risk groups.

Factors correlated with traffic accidents as a basis for evaluating Advanced Driver Assistance Systems.

PubMed

Staubach, Maria

2009-09-01

This study aims to identify factors which influence and cause errors in traffic accidents and to use these as a basis for information to guide the application and design of driver assistance systems. A total of 474 accidents were examined in depth for this study by means of a psychological survey, data from accident reports, and technical reconstruction information. An error analysis was subsequently carried out, taking into account the driver, environment, and vehicle sub-systems. Results showed that all accidents were influenced by errors as a consequence of distraction and reduced activity. For crossroad accidents, there were further errors resulting from sight obstruction, masked stimuli, focus errors, and law infringements. Lane departure crashes were additionally caused by errors as a result of masked stimuli, law infringements, expectation errors as well as objective and action slips, while same direction accidents occurred additionally because of focus errors, expectation errors, and objective and action slips. Most accidents were influenced by multiple factors. There is a safety potential for Advanced Driver Assistance Systems (ADAS), which support the driver in information assimilation and help to avoid distraction and reduced activity. The design of the ADAS is dependent on the specific influencing factors of the accident type.

[Analysis of accidents for magnetically induced displacement of the large ferromagnetic material in magnetic resonance systems].

PubMed

Yamatani, Yuya; Doi, Tsukasa; Ueyama, Tsuyoshi; Nishiki, Shigeo; Ogura, Akio; Kawamitsu, Hideaki; Tsuchihashi, Toshio; Okuaki, Tomoyuki; Matsuda, Tsuyoshi

2013-01-01

To improve magnetic resonance (MR) safety, we surveyed the accidents caused by large ferromagnetic materials brought into MR systems accidentally. We sent a questionnaire to 700 Japanese medical institutions and received 405 valid responses (58%). A total of 97 accidents in 77 institutions were observed and we analyzed them regarding incidental rate, the detail situation and environmental factors. The mean accident rate of each institute was 0.7/100,000 examinations, which was widely distributed (0-25.6/100,000) depending on the institute. In this survey, relatively small institutes with less than 500 beds tend to have these accidents more frequently (p<0.01). The institutes in which daily MR examination counts are more than 10 patients have fewer accidents than those with less than 10 daily examinations. The institutes with 6-10 MR examinations daily have significantly more accidents than that with more than 10 daily MR examinations (p<0.01). The main mental factors of the accidents were considered to be "prejudice" and "carelessness" but some advocate "ignorance." Though we could not find significant reduction in the institutes that have lectures and training for MR safety, we should continue lectures and training for MR safety to reduce accidents due to "ignorance."

Effective environmental factors on geographical distribution of traffic accidents on pedestrians, downtown Tehran city.

PubMed

Moradi, Ali; Soori, Hamid; Kavousi, Amir; Eshghabadi, Farshid; Nematollahi, Shahrzad; Zeini, Salahdien

2017-01-01

In most countries, occurrence of traffic causalities is high in pedestrians. The aim of this study is to geographically analyze the traffic casualties in pedestrians in downtown Tehran city. The study population consisted of traffic injury accidents in pedestrians occurred during 2015 in Tehran city. Data were extracted from offices of traffic police and municipality. For analysis of environmental factors and site of accidents, ordinary least square regression models and geographically weighted regression were used. Fitness and performance of models were checked using the Akaike information criteria, Bayesian information criteria, deviance, and adjusted R 2 . Totally, 514 accidents were included in this study. Of them, site of accidents was arterial streets in 370 (71.9%) cases, collector streets in 133 cases (25.2%), and highways in 11 cases (2.1%). Geographical units of traffic accidents in pedestrians had statistically significant relationship with a number of bus stations, number of crossroads, and recreational areas. Distribution of injury traffic accidents in pedestrians is different in downtown Tehran city. Neighborhoods close to markets are considered as most dangerous neighborhoods for injury traffic accidents. Different environmental factors are involved in determining the distribution of these accidents. The health of pedestrians in Tehran city can be improved by proper traffic management, control of environmental factors, and educational programs.

Factors contributing to young moped rider accidents in Denmark.

PubMed

Møller, Mette; Haustein, Sonja

2016-02-01

Young road users still constitute a high-risk group with regard to road traffic accidents. The crash rate of a moped is four times greater than that of a motorcycle, and the likelihood of being injured in a road traffic accident is 10-20 times higher among moped riders compared to car drivers. Nevertheless, research on the behaviour and accident involvement of young moped riders remains sparse. Based on analysis of 128 accident protocols, the purpose of this study was to increase knowledge about moped accidents. The study was performed in Denmark involving riders aged 16 or 17. A distinction was made between accident factors related to (1) the road and its surroundings, (2) the vehicle, and (3) the reported behaviour and condition of the road user. Thirteen accident factors were identified with the majority concerning the reported behaviour and condition of the road user. The average number of accident factors assigned per accident was 2.7. Riding speed was assigned in 45% of the accidents which made it the most frequently assigned factor on the part of the moped rider followed by attention errors (42%), a tuned up moped (29%) and position on the road (14%). For the other parties involved, attention error (52%) was the most frequently assigned accident factor. The majority (78%) of the accidents involved road rule breaching on the part of the moped rider. The results indicate that preventive measures should aim to eliminate violations and increase anticipatory skills among moped riders and awareness of mopeds among other road users. Due to their young age the effect of such measures could be enhanced by infrastructural measures facilitating safe interaction between mopeds and other road users. Copyright © 2015 Elsevier Ltd. All rights reserved.

Parallel sequencing lives, or what makes large sequencing projects successful

PubMed Central

Cuartero, Yasmina; Stadhouders, Ralph; Graf, Thomas; Marti-Renom, Marc A; Beato, Miguel

2017-01-01

Abstract T47D_rep2 and b1913e6c1_51720e9cf were 2 Hi-C samples. They were born and processed at the same time, yet their fates were very different. The life of b1913e6c1_51720e9cf was simple and fruitful, while that of T47D_rep2 was full of accidents and sorrow. At the heart of these differences lies the fact that b1913e6c1_51720e9cf was born under a lab culture of Documentation, Automation, Traceability, and Autonomy and compliance with the FAIR Principles. Their lives are a lesson for those who wish to embark on the journey of managing high-throughput sequencing data. PMID:29048533

Source term estimation of radioxenon released from the Fukushima Dai-ichi nuclear reactors using measured air concentrations and atmospheric transport modeling.

PubMed

Eslinger, P W; Biegalski, S R; Bowyer, T W; Cooper, M W; Haas, D A; Hayes, J C; Hoffman, I; Korpach, E; Yi, J; Miley, H S; Rishel, J P; Ungar, K; White, B; Woods, V T

2014-01-01

Systems designed to monitor airborne radionuclides released from underground nuclear explosions detected radioactive fallout across the northern hemisphere resulting from the Fukushima Dai-ichi Nuclear Power Plant accident in March 2011. Sampling data from multiple International Modeling System locations are combined with atmospheric transport modeling to estimate the magnitude and time sequence of releases of (133)Xe. Modeled dilution factors at five different detection locations were combined with 57 atmospheric concentration measurements of (133)Xe taken from March 18 to March 23 to estimate the source term. This analysis suggests that 92% of the 1.24 × 10(19) Bq of (133)Xe present in the three operating reactors at the time of the earthquake was released to the atmosphere over a 3 d period. An uncertainty analysis bounds the release estimates to 54-129% of available (133)Xe inventory. Copyright © 2013 Elsevier Ltd. All rights reserved.

[Severe parachuting accident. Analysis of 122 cases].

PubMed

Krauss, U; Mischkowsky, T

1993-06-01

Based on a population of 122 severely injured patients the causes of paragliding accidents and the patterns of injury are analyzed. A questionnaire is used to establish a sport-specific profile for the paragliding pilot. The lower limbs (55.7%) and the lower parts of the spine (45.9%) are the most frequently injured parts of the body. There is a high risk of multiple injuries after a single accident because of the tremendous axial power. The standard of equipment is good in over 90% of the cases. Insufficient training and failure to take account of geographical and meteorological conditions are the main determinants of accidents sustained by paragliders, most of whom are young. Nevertheless, 80% of our patients want to continue paragliding. Finally some advice is given on how to prevent paragliding accidents and injuries.

Analysis of accidents with organic material in health workers.

PubMed

Vieira, Mariana; Padilha, Maria Itayra; Pinheiro, Regina Dal Castel

2011-01-01

This retrospective and descriptive study with a quantitative design aimed to evaluate occupational accidents with exposure to biological material, as well as the profile of workers, based on reporting forms sent to the Regional Reference Center of Occupational Health in Florianópolis/SC. Data collection was carried out through a survey of 118 reporting forms in 2007. Data were analyzed electronically. The occurrence of accidents was predominantly among nursing technicians, women and the mean age was 34.5 years. 73% of accidents involved percutaneous exposure, 78% had blood and fluid with blood, 44.91% resulted from invasive procedures. It was concluded that strategies to prevent the occurrence of accidents with biological material should include joint activities between workers and service management and should be directed at improving work conditions and organization.

Analysis of construction accidents in Turkey and responsible parties.

PubMed

Gürcanli, G Emre; Müngen, Uğur

2013-01-01

Construction is one of the world's biggest industry that includes jobs as diverse as building, civil engineering, demolition, renovation, repair and maintenance. Construction workers are exposed to a wide variety of hazards. This study analyzes 1,117 expert witness reports which were submitted to criminal and labour courts. These reports are from all regions of the country and cover the period 1972-2008. Accidents were classified by the consequence of the incident, time and main causes of the accident, construction type, occupation of the victim, activity at time of the accident and party responsible for the accident. Falls (54.1%), struck by thrown/falling object (12.9%), structural collapses (9.9%) and electrocutions (7.5%) rank first four places. The accidents were most likely between the hours 15:00 and 17:00 (22.6%), 10:00-12:00 (18.7%) and just after the lunchtime (9.9%). Additionally, the most common accidents were further divided into sub-types. Expert-witness assessments were used to identify the parties at fault and what acts of negligence typically lead to accidents. Nearly two thirds of the faulty and negligent acts are carried out by the employers and employees are responsible for almost one third of all cases.

The effect of road characteristics on motorcycle accident in Batu east Java Indonesia

NASA Astrophysics Data System (ADS)

Abusini, Sobri

2013-09-01

Safe of transportation on road is global problem with not only transportation problem, but also social teritory problem in sosial life. WHO pay attention to safe transportation on road to decide healthy day in the world 2004 with caption: Road Safety is no Accident. WHO is clariafy that road accident level in the world have to reach 1.2 mellion victim death and over 30 mellion injuries every year. As much 85% sacrifice death are accident in develop state, where vehicle number only 32% from vehicle number in the world. That becouse as the objective is to decide influence road charakteristics geometrics for motorcycle accident in Batu East Java Indonesia. Using some statistical analysis it is found that the best-fit motorcycle accident model is: Acc = 0,009F0,703exp(-0,334SW-0,361G+0.077S) Where: Acc = number of accident, F = Flow, pcu/hr, SW = shoulder width (m), S = speed, km/hr, G = Gradient (0,1) The model shows that the affecting factors are flow, shoulder width and speed, therefore local government should improve some related factor (flow, shoulder width, Gradient and speed) that can reduce the number of motorcycle accident at crossing road in Batu.

Precursors of dangerous substances formed in the loss of control of chemical systems.

PubMed

Cozzani, V; Zanelli, S

1999-03-01

Article 2 of Directive 96/82/EC on the control of major accident hazards caused by dangerous substances requires to consider also the hazards due to the dangerous substances "which it is believed may be generated during loss of control of an industrial chemical process", although no generally accepted guidelines are available for the identification of these substances. In the present study, the accidents involving the unwanted formation of dangerous substances as a consequence of the loss of control of chemical systems were investigated. A specifically developed database was used, containing data on more than 400 of these accidents and on the substances involved. The hazardous substances formed in the accidents and the precursors of these substances were identified. The influence of accident characteristics on the substances formed was investigated. In the context of the application of Directive 96/82/EC, an accident severity index and a hazard rating of the precursors of dangerous substances formed in the accidents were proposed. A lumping approach was used in order to develop schemes for the preliminary identification of substances that may be formed in the loss of control of chemical system. The results of accident analysis were used to test the schemes developed.

The effect of road and environmental characteristics on pedestrian hit-and-run accidents in Ghana.

PubMed

Aidoo, Eric Nimako; Amoh-Gyimah, Richard; Ackaah, Williams

2013-04-01

The number of pedestrians who have died as a result of being hit by vehicles has increased in recent years, in addition to vehicle passenger deaths. Many pedestrians who were involved in road traffic accident died as a result of the driver leaving the pedestrian who was struck unattended at the scene of the accident. This paper seeks to determine the effect of road and environmental characteristics on pedestrian hit-and-run accidents in Ghana. Using pedestrian accident data extracted from the National Road Traffic Accident Database at the Building and Road Research Institute (BRRI) of the Council for Scientific and Industrial Research (CSIR), Ghana, a binary logit model was employed in the analysis. The results from the estimated model indicate that fatal accidents, unclear weather, nighttime conditions, and straight and flat road sections without medians and junctions significantly increase the likelihood that the vehicle driver will leave the scene after hitting a pedestrian. Thus, integrating median separation and speed humps into road design and construction and installing street lights will help to curb the problem of pedestrian hit-and-run accidents in Ghana. Copyright © 2012 Elsevier Ltd. All rights reserved.

A study of NASA occupational injuries and property damage at Goddard Space Flight Center, Langley Research Center and Headquarters

NASA Technical Reports Server (NTRS)

1976-01-01

Analysis of NASA's accident/injury/illness and health data was performed. The analysis included: (1) an on-site study of the existing data; (2) evaluation of the findings to develop criteria for the subsequent implementation of safety and health standards; (3) preparation of a graphical loss control assessment; and (4) recommendations to reduce accident rates.

Road accidents caused by drivers falling asleep.

PubMed

Sagberg, F

1999-11-01

About 29600 Norwegian accident-involved drivers received a questionnaire about the last accident reported to their insurance company. About 9200 drivers (31%) returned the questionnaire. The questionnaire contained questions about sleep or fatigue as contributing factors to the accident. In addition, the drivers reported whether or not they had fallen asleep some time whilst driving. and what the consequences had been. Sleep or drowsiness was a contributing factor in 3.9% of all accidents, as reported by drivers who were at fault for the accident. This factor was strongly over-represented in night-time accidents (18.6%), in running-off-the-road accidents (8.3%), accidents after driving more than 150 km on one trip (8.1%), and personal injury accidents (7.3%). A logistic regression analysis showed that the following additional factors made significant and independent contributions to increasing the odds of sleep involvement in an accident: dry road, high speed limit, driving one's own car, not driving the car daily, high education, and few years of driving experience. More male than female drivers were involved in sleep-related accidents, but this seems largely to be explained by males driving relatively more than females on roads with high speed limits. A total of 10% of male drivers and 4% of females reported to have fallen asleep while driving during the last 12 months. A total of 4% of these events resulted in an accident. The most frequent consequence of falling asleep--amounting to more than 40% of the reported incidents--was crossing of the right edge-line before awaking, whereas crossing of the centreline was reported by 16%. Drivers' lack of awareness of important precursors of falling asleep--like highway hypnosis, driving without awareness, and similar phenomena--as well as a reluctance to discontinue driving despite feeling tired are pointed out as likely contributors to sleep-related accidents. More knowledge about the drivers' experiences immediately preceding such accidents may give a better background for implementing effective driver warning systems and other countermeasures.

Worker safety and injury severity analysis of earthmoving equipment accidents.

PubMed

Kazan, Emrah; Usmen, Mumtaz A

2018-06-01

Research on construction worker safety associated with construction equipment has mostly focused on accident type rather than injury severity and the embedded factor relationships. Significant variables and their effects on the degree of injury are examined for earthmoving equipment using data from OSHA. Four types of equipment, backhoe, bulldozer, excavator, and scraper are included in the study. Accidents involving on-foot workers and equipment operators are investigated collectively, as well as separately. Cross tabulation analysis was conducted to establish the associations between selected categorical variables, using degree of injury as a dichotomous dependent variable (fatal vs. nonfatal) and a number of independent variables having different values. Odds ratios were calculated to determine how much a certain variable/factor increases the odds of fatality in an accident, and the odds ratios were ranked to determine the relative impact of a given factor. It was found that twelve variables were significantly associated with injury severity. Rankings based on odds ratios showed that inadequate safety training (2.54), missing equipment protective system (2.38), being a non-union worker (2.26), being an equipment operator (1.93), and being on or around inadequately maintained equipment (1.58) produced higher odds for fatality. A majority of the earthmoving equipment accidents resulted in fatality. Backhoes were the most common equipment involved in accidents and fatalities. Struck-by accidents were the most prevalent and most fatal. Non-OSHA compliant safety training, missing seatbelt, operator not using seatbelt, malfunctioning back-up alarms, and poorly maintained equipment were factors contributing to accidents and fatalities. On-foot workers experienced a higher number of accidents than operators, while fatality odds were higher for the operators. Practical applications: Safety professionals should benefit from our findings in planning and delivering training and providing oversight to workers in earthmoving equipment operations. Copyright © 2018 National Safety Council and Elsevier Ltd. All rights reserved.

Grouping of body areas affected in traffic accidents. A cohort study.

PubMed

León, Alba Luz; Ascuntar-Tello, Johana; Valderrama-Molina, Carlos Oliver; Giraldo, Nelson Darío; Constaín, Alfredo; Puerta, Andrés; Restrepo, Camilo; Jaimes, Fabián

2018-03-01

Traffic accidents are considered a public health problem and, according to the World Health Organization, currently is the eighth cause of death in the world. Specifically, pedestrians, cyclists and motorcyclists contribute half of the fatalities. Adequate clinical management in accordance with aggregation patterns of the body areas involved, as well as the characteristics of the accident, will help to reduce mortality and disability in this population. Secondary data analysis of a cohort of patients involved in traffic accidents and admitted to the emergency room (ER) of a high complexity hospital in Medellín, Colombia. They were over 15 years of age, had two or more injuries in different areas of the body and had a hospital stay of more than 24 h after admission. A cluster analysis was performed, using Ward's method and the linfinity similarity measure, to obtain clusters of body areas most commonly affected depending on the type of vehicle and the type of victim. Among 2445 patients with traffic accidents, 34% (n = 836) were admitted into the Intensive Care Unit (ICU) and the overall hospital mortality rate was 8% (n = 201). More than 50% of the patients were motorcycle riders but mortality was higher in pedestrian-car accidents (16%, n = 34). The clusters show efficient performance to separate the population depending on the severity of their injuries. Pedestrians had the highest mortality after having accidents with cars and they also had the highest number of body parts clustered, mainly on head and abdomen areas. Exploring the cluster patterns of injuries and body areas affected in traffic accidents allow to establish anatomical groups defined by the type of accident and the type of vehicle. This classification system will accelerate and prioritize ER-care for these population groups, helping to provide better health care services and to rationalize available resources.

Corruption of genomic databases with anomalous sequence.

PubMed

Lamperti, E D; Kittelberger, J M; Smith, T F; Villa-Komaroff, L

1992-06-11

We describe evidence that DNA sequences from vectors used for cloning and sequencing have been incorporated accidentally into eukaryotic entries in the GenBank database. These incorporations were not restricted to one type of vector or to a single mechanism. Many minor instances may have been the result of simple editing errors, but some entries contained large blocks of vector sequence that had been incorporated by contamination or other accidents during cloning. Some cases involved unusual rearrangements and areas of vector distant from the normal insertion sites. Matches to vector were found in 0.23% of 20,000 sequences analyzed in GenBank Release 63. Although the possibility of anomalous sequence incorporation has been recognized since the inception of GenBank and should be easy to avoid, recent evidence suggests that this problem is increasing more quickly than the database itself. The presence of anomalous sequence may have serious consequences for the interpretation and use of database entries, and will have an impact on issues of database management. The incorporated vector fragments described here may also be useful for a crude estimate of the fidelity of sequence information in the database. In alignments with well-defined ends, the matching sequences showed 96.8% identity to vector; when poorer matches with arbitrary limits were included, the aggregate identity to vector sequence was 94.8%.

NASA Structural Analysis Report on the American Airlines Flight 587 Accident - Local Analysis of the Right Rear Lug

NASA Technical Reports Server (NTRS)

Raju, Ivatury S; Glaessgen, Edward H.; Mason, Brian H; Krishnamurthy, Thiagarajan; Davila, Carlos G

2005-01-01

A detailed finite element analysis of the right rear lug of the American Airlines Flight 587 - Airbus A300-600R was performed as part of the National Transportation Safety Board s failure investigation of the accident that occurred on November 12, 2001. The loads experienced by the right rear lug are evaluated using global models of the vertical tail, local models near the right rear lug, and a global-local analysis procedure. The right rear lug was analyzed using two modeling approaches. In the first approach, solid-shell type modeling is used, and in the second approach, layered-shell type modeling is used. The solid-shell and the layered-shell modeling approaches were used in progressive failure analyses (PFA) to determine the load, mode, and location of failure in the right rear lug under loading representative of an Airbus certification test conducted in 1985 (the 1985-certification test). Both analyses were in excellent agreement with each other on the predicted failure loads, failure mode, and location of failure. The solid-shell type modeling was then used to analyze both a subcomponent test conducted by Airbus in 2003 (the 2003-subcomponent test) and the accident condition. Excellent agreement was observed between the analyses and the observed failures in both cases. From the analyses conducted and presented in this paper, the following conclusions were drawn. The moment, Mx (moment about the fuselage longitudinal axis), has significant effect on the failure load of the lugs. Higher absolute values of Mx give lower failure loads. The predicted load, mode, and location of the failure of the 1985-certification test, 2003-subcomponent test, and the accident condition are in very good agreement. This agreement suggests that the 1985-certification and 2003- subcomponent tests represent the accident condition accurately. The failure mode of the right rear lug for the 1985-certification test, 2003-subcomponent test, and the accident load case is identified as a cleavage-type failure. For the accident case, the predicted failure load for the right rear lug from the PFA is greater than 1.98 times the limit load of the lugs. I.

Safety at Passive Grade Crossings. Volume 1 : Analysis

DOT National Transportation Integrated Search

1998-07-21

More than 4,000 accidents have occurred at the nation's active and passive grade crossings each year from 1991 through 1996. Many of the accidents at active crossings have involved highway vehicle drivers who did not comply with train-activated warni...

Usage and effectiveness of seat and shoulder belts in rural Pennsylvania accidents

DOT National Transportation Integrated Search

1974-12-01

This report presents an analysis of lap-belt and shoulder- belt usage and effectiveness in rural Pennsylvania accidents. The data were collected by the Pennsylvania State Police under an agreement with the National Highway Traffic Safety Administrati...

Recommendations for shoulder restraint installation in general aviation aircraft.

DOT National Transportation Integrated Search

1966-09-01

The use of inadequate or incomplete body restraint systems is a major factor in the current trend of increasing serious and fatal type injuries reported from general aviation accidents. An analysis of these accident injuries and conditions clearly in...

The analysis of benzodiazepines in forensic urine samples.

DOT National Transportation Integrated Search

1996-04-01

The FAA Toxicology and Accident Research Laboratory reports the presence of any drug detected at therapeutic or subtherapeutic levels and the medical condition for which the drug may have been used. Specimens from the pilot of a fatal aviation accide...

An analysis of drivers most responsible for fatal accidents versus a control sample

DOT National Transportation Integrated Search

1976-05-01

Author's abstract: Recently the Boston University Traffic Accident Research Special Study Team has completed the investigation of an experimental driver sample consisting of 267 motor vehicle operators judged to have been 'most responsible" for a hig...

An analysis of drivers most responsible for fatal accidents versus a control sample

DOT National Transportation Integrated Search

1975-11-01

Author's abstract: Recently the Boston University Traffic Accident Research Special Study Team has completed the investigation of an experimental driver sample consisting of 267 motor vehicle operators judged to have been most responsible" for a high...

Reduction of police vehicle accidents through mechaniically aided supervision

PubMed Central

Larson, Lynn D.; Schnelle, John F.; Kirchner, Robert; Carr, Adam F.; Domash, Michele; Risley, Todd R.

1980-01-01

Tachograph recorders were installed in 224 vehicles of a metropolitan police department to monitor vehicle operation in an attempt to reduce the rate of accidents. Police sergeants reviewed each tachograph chart and provided feedback to officers regarding their driving performance. Reliability checks and additional feedback procedures were implemented so that upper level supervisors monitored and controlled the performance of field sergeants. The tachograph intervention and components of the feedback system nearly eliminated personal injury accidents and sharply reduced accidents caused by officer negligence. A cost-benefit analysis revealed that the savings in vehicle repair and injury claims outweighed the equipment and operating costs. PMID:16795634