Science.gov

Sample records for achieve greater reliability

  1. Multisensor Arrays for Greater Reliability and Accuracy

    NASA Technical Reports Server (NTRS)

    Immer, Christopher; Eckhoff, Anthony; Lane, John; Perotti, Jose; Randazzo, John; Blalock, Norman; Ree, Jeff

    2004-01-01

    Arrays of multiple, nominally identical sensors with sensor-output-processing electronic hardware and software are being developed in order to obtain accuracy, reliability, and lifetime greater than those of single sensors. The conceptual basis of this development lies in the statistical behavior of multiple sensors and a multisensor-array (MSA) algorithm that exploits that behavior. In addition, advances in microelectromechanical systems (MEMS) and integrated circuits are exploited. A typical sensor unit according to this concept includes multiple MEMS sensors and sensor-readout circuitry fabricated together on a single chip and packaged compactly with a microprocessor that performs several functions, including execution of the MSA algorithm. In the MSA algorithm, the readings from all the sensors in an array at a given instant of time are compared and the reliability of each sensor is quantified. This comparison of readings and quantification of reliabilities involves the calculation of the ratio between every sensor reading and every other sensor reading, plus calculation of the sum of all such ratios. Then one output reading for the given instant of time is computed as a weighted average of the readings of all the sensors. In this computation, the weight for each sensor is the aforementioned value used to quantify its reliability. In an optional variant of the MSA algorithm that can be implemented easily, a running sum of the reliability value for each sensor at previous time steps as well as at the present time step is used as the weight of the sensor in calculating the weighted average at the present time step. In this variant, the weight of a sensor that continually fails gradually decreases, so that eventually, its influence over the output reading becomes minimal: In effect, the sensor system "learns" which sensors to trust and which not to trust. The MSA algorithm incorporates a criterion for deciding whether there remain enough sensor readings that

  2. DOD Joint Bases: Management Improvements Needed to Achieve Greater Efficiencies

    DTIC Science & Technology

    2012-11-01

    Joint Bases Realign Fort Eustis, VA, by relocating the installation management functions to Langley AFB, VA. Realign Fort Story , VA, by...the installation management functions to L·mglcy AFB, VA. Realign Fort Story , VA, by relocating the installation management functions to Commander...DOD JOINT BASES Management Improvements Needed to Achieve Greater Efficiencies Report to Congressional Addressees

  3. Reliability achievement in high technology space systems

    NASA Technical Reports Server (NTRS)

    Lindstrom, D. L.

    1981-01-01

    The production of failure-free hardware is discussed. The elements required to achieve such hardware are: technical expertise to design, analyze, and fully understand the design; use of high reliability parts and materials control in the manufacturing process; and testing to understand the system and weed out defects. The durability of the Hughes family of satellites is highlighted.

  4. Understanding the Elements of Operational Reliability: A Key for Achieving High Reliability

    NASA Technical Reports Server (NTRS)

    Safie, Fayssal M.

    2010-01-01

    This viewgraph presentation reviews operational reliability and its role in achieving high reliability through design and process reliability. The topics include: 1) Reliability Engineering Major Areas and interfaces; 2) Design Reliability; 3) Process Reliability; and 4) Reliability Applications.

  5. Achieving Reliable Communication in Dynamic Emergency Responses

    PubMed Central

    Chipara, Octav; Plymoth, Anders N.; Liu, Fang; Huang, Ricky; Evans, Brian; Johansson, Per; Rao, Ramesh; Griswold, William G.

    2011-01-01

    Emergency responses require the coordination of first responders to assess the condition of victims, stabilize their condition, and transport them to hospitals based on the severity of their injuries. WIISARD is a system designed to facilitate the collection of medical information and its reliable dissemination during emergency responses. A key challenge in WIISARD is to deliver data with high reliability as first responders move and operate in a dynamic radio environment fraught with frequent network disconnections. The initial WIISARD system employed a client-server architecture and an ad-hoc routing protocol was used to exchange data. The system had low reliability when deployed during emergency drills. In this paper, we identify the underlying causes of unreliability and propose a novel peer-to-peer architecture that in combination with a gossip-based communication protocol achieves high reliability. Empirical studies show that compared to the initial WIISARD system, the redesigned system improves reliability by as much as 37% while reducing the number of transmitted packets by 23%. PMID:22195075

  6. Methods and Costs to Achieve Ultra Reliable Life Support

    NASA Technical Reports Server (NTRS)

    Jones, Harry W.

    2012-01-01

    A published Mars mission is used to explore the methods and costs to achieve ultra reliable life support. The Mars mission and its recycling life support design are described. The life support systems were made triply redundant, implying that each individual system will have fairly good reliability. Ultra reliable life support is needed for Mars and other long, distant missions. Current systems apparently have insufficient reliability. The life cycle cost of the Mars life support system is estimated. Reliability can be increased by improving the intrinsic system reliability, adding spare parts, or by providing technically diverse redundant systems. The costs of these approaches are estimated. Adding spares is least costly but may be defeated by common cause failures. Using two technically diverse systems is effective but doubles the life cycle cost. Achieving ultra reliability is worth its high cost because the penalty for failure is very high.

  7. Reliability Technology to Achieve Insertion of Advanced Packaging (RELTECH) program

    NASA Technical Reports Server (NTRS)

    Fayette, Daniel F.; Speicher, Patricia; Stoklosa, Mark J.; Evans, Jillian V.; Evans, John W.; Gentile, Mike; Pagel, Chuck A.; Hakim, Edward

    1993-01-01

    A joint military-commercial effort to evaluate multichip module (MCM) structures is discussed. The program, Reliability Technology to Achieve Insertion of Advanced Packaging (RELTECH), has been designed to identify the failure mechanisms that are possible in MCM structures. The RELTECH test vehicles, technical assessment task, product evaluation plan, reliability modeling task, accelerated and environmental testing, and post-test physical analysis and failure analysis are described. The information obtained through RELTECH can be used to address standardization issues, through development of cost effective qualification and appropriate screening criteria, for inclusion into a commercial specification and the MIL-H-38534 general specification for hybrid microcircuits.

  8. Achieving High Reliability Operations Through Multi-Program Integration

    SciTech Connect

    Holly M. Ashley; Ronald K. Farris; Robert E. Richards

    2009-04-01

    Over the last 20 years the Idaho National Laboratory (INL) has adopted a number of operations and safety-related programs which has each periodically taken its turn in the limelight. As new programs have come along there has been natural competition for resources, focus and commitment. In the last few years, the INL has made real progress in integrating all these programs and are starting to realize important synergies. Contributing to this integration are both collaborative individuals and an emerging shared vision and goal of the INL fully maturing in its high reliability operations. This goal is so powerful because the concept of high reliability operations (and the resulting organizations) is a masterful amalgam and orchestrator of the best of all the participating programs (i.e. conduct of operations, behavior based safety, human performance, voluntary protection, quality assurance, and integrated safety management). This paper is a brief recounting of the lessons learned, thus far, at the INL in bringing previously competing programs into harmony under the goal (umbrella) of seeking to perform regularly as a high reliability organization. In addition to a brief diagram-illustrated historical review, the authors will share the INL’s primary successes (things already effectively stopped or started) and the gaps yet to be bridged.

  9. Validity and Reliability of Trichotomous Achievement Goal Scale

    ERIC Educational Resources Information Center

    Ilker, Gokce Erturan; Arslan, Yunus; Demirhan, Giyasettin

    2011-01-01

    The Trichotomous Achievement Goal Scale was developed by Agbuga and Xiang (2008) by including selected items from the scales of Duda and Nicholls (1992), Elliot (1999), and Elliot and Church (1997) and adapting them into Turkish. The scale consists of 18 items, and students rated each item on a 7-point Likert scale. To ascertain the validity and…

  10. Desert ants achieve reliable recruitment across noisy interactions.

    PubMed

    Razin, Nitzan; Eckmann, Jean-Pierre; Feinerman, Ofer

    2013-05-06

    We study how desert ants, Cataglyphis niger, a species that lacks pheromone-based recruitment mechanisms, inform each other about the presence of food. Our results are based on automated tracking that allows us to collect a large database of ant trajectories and interactions. We find that interactions affect an ant's speed within the nest. Fast ants tend to slow down, whereas slow ones increase their speed when encountering a faster ant. Faster ants tend to exit the nest more frequently than slower ones. So, if an ant gains enough speed through encounters with others, then she tends to leave the nest and look for food. On the other hand, we find that the probability for her to leave the nest depends only on her speed, but not on whether she had recently interacted with a recruiter that has found the food. This suggests a recruitment system in which ants communicate their state by very simple interactions. Based on this assumption, we estimate the information-theoretical channel capacity of the ants' pairwise interactions. We find that the response to the speed of an interacting nest-mate is very noisy. The question is then how random interactions with ants within the nest can be distinguished from those interactions with a recruiter who has found food. Our measurements and model suggest that this distinction does not depend on reliable communication but on behavioural differences between ants that have found the food and those that have not. Recruiters retain high speeds throughout the experiment, regardless of the ants they interact with; non-recruiters communicate with a limited number of nest-mates and adjust their speed following these interactions. These simple rules lead to the formation of a bistable switch on the level of the group that allows the distinction between recruitment and random noise in the nest. A consequence of the mechanism we propose is a negative effect of ant density on exit rates and recruitment success. This is, indeed, confirmed by our

  11. Creating conditions for greater private sector participation in achieving contraceptive security.

    PubMed

    Sharma, Suneeta; Dayaratna, Varuni

    2005-03-01

    The growing gap between donor/government funding and the expected need for contraceptives is an issue of great concern for most developing countries. Addressing this resource shortfall, and meeting the goals of contraceptive security requires that countries mobilize the full and active participation of the private sector in the contraceptive market. Private sector involvement will not only increase the resource base available for contraceptives, it can also free up scarce donor and government resources to serve those who have the greatest need for public subsidies. This paper provides an overview of policy processes, strategies, and tools that can be used in developing countries to create an enabling environment for greater private sector participation, foster complementary public-private sector roles, and enhance the contribution of the private sector to contraceptive security.

  12. A New Technique for Achieving Impact Velocities Greater Than 10 km/sec

    NASA Technical Reports Server (NTRS)

    Piekutowski, A. J.; Nolen, Angie (Technical Monitor)

    2001-01-01

    This Contractor Report describes and presents the results of work that was done in an attempt to develop an augmented acceleration technique that would launch small projectiles of known shape, mass, and state to velocities of 10 km/sec and higher. The higher velocities were to be achieved by adding a third stage to a conventional two-stage, light-gas gun and using a modified firing cycle for the third stage. The technique did not achieve the desired results and was modified for use during the development program. Since the design of the components used for the augmented-acceleration, three-stage launcher could be readily adapted for use as a three-stage launcher that used a single-stage acceleration cycle; the remainder of the contract period was spent performing test firings using the modified three-stage launcher. Work with the modified three-stage launcher, although not complete, did produce test firings in which an 0.11-g cylindrical nylon projectile was launched to a velocity of 8.65 km/sec.

  13. Academic Achievement, Academic Self-Concept, and Academic Motivation of Immigrant Adolescents in the Greater Toronto Area Secondary Schools

    ERIC Educational Resources Information Center

    Areepattamannil, Shaljan; Freeman, John G.

    2008-01-01

    The study examined the self-reported academic achievement, academic self-concept, and academic motivation of 573 immigrant and nonimmigrant adolescents in the Greater Toronto Area (GTA) secondary schools. Descriptive Discriminant Analyses indicated that the immigrant adolescents had higher performance in mathematics, higher math and school…

  14. Development of Achievement Test: Validity and Reliability Study for Achievement Test on Matter Changing

    ERIC Educational Resources Information Center

    Kara, Filiz; Celikler, Dilek

    2015-01-01

    For "Matter Changing" unit included in the Secondary School 5th Grade Science Program, it is intended to develop a test conforming the gains described in the program, and that can determine students' achievements. For this purpose, a multiple-choice test of 48 questions is arranged, consisting of 8 questions for each gain included in the…

  15. Mechanized pivot shift test achieves greater accuracy than manual pivot shift test.

    PubMed

    Musahl, Volker; Voos, James; O'Loughlin, Padhraig F; Stueber, Volker; Kendoff, Daniel; Pearle, Andrew D

    2010-09-01

    The objective of this study was to design a navigated mechanized pivot shift test setup and evaluate its repeatability in the ACL-deficient knee. It was hypothesized that translations and rotations measured with the mechanized pivot shift would be more repeatable when compared to those obtained with a manual pivot shift. Twelve fresh frozen cadaveric hip-to-toe whole lower extremities were used for this study. A manual pivot shift test was performed in the intact knee and in the ACL-deficient knee and was repeated three times. A navigation system simultaneously recorded tibial translation and rotation. The mechanized pivot shift test consists of a modified continuous passive motion (CPM) machine and a custom-made foot holder to allow for the application of internal rotation moments at the knee. Valgus moments were achieved by a 45 degrees tilt of the CPM machine with respect to the supine position and a Velcro strap secured across the proximal tibia. The mechanized pivot shift was repeated three times. Repeated measures ANOVA was used to compare manual and mechanized pivot shift testing. An intra-class correlation coefficient (ICC) was used to determine variability within each knee at each testing condition. In the ACL-deficient knee, translation with manual pivot shift testing (11.7 +/- 2.6 mm) was significantly higher than with mechanized pivot shift testing (7.4 +/- 2.5 mm; p < 0.05). Rotation with the manual pivot shift testing (18.6 +/- 5.4 degrees) was also significantly higher than with mechanized pivot shift testing (11.0 +/- 2.3 degrees; p < 0.05). The intra-class ICC for translations was 0.76 for manual pivot shift and 0.92 for the mechanized pivot shift test. The intra-class ICC for rotations was 0.89 for manual pivot shift and 0.82 for the mechanized pivot shift test. This study introduced a modified CPM for mechanized pivot shift testing. Although recorded translations and rotations with the mechanized pivot shift test were lower than with manual

  16. Fair and Just Culture, Team Behavior, and Leadership Engagement: The Tools to Achieve High Reliability

    PubMed Central

    Frankel, Allan S; Leonard, Michael W; Denham, Charles R

    2006-01-01

    Background Disparate health care provider attitudes about autonomy, teamwork, and administrative operations have added to the complexity of health care delivery and are a central factor in medicine's unacceptably high rate of errors. Other industries have improved their reliability by applying innovative concepts to interpersonal relationships and administrative hierarchical structures (Chandler 1962). In the last 10 years the science of patient safety has become more sophisticated, with practical concepts identified and tested to improve the safety and reliability of care. Objective Three initiatives stand out as worthy regarding interpersonal relationships and the application of provider concerns to shape operational change: The development and implementation of Fair and Just Culture principles, the broad use of Teamwork Training and Communication, and tools like WalkRounds that promote the alignment of leadership and frontline provider perspectives through effective use of adverse event data and provider comments. Methods Fair and Just Culture, Teamwork Training, and WalkRounds are described, and implementation examples provided. The argument is made that they must be systematically and consistently implemented in an integrated fashion. Conclusions There are excellent examples of institutions applying Just Culture principles, Teamwork Training, and Leadership WalkRounds—but to date, they have not been comprehensively instituted in health care organizations in a cohesive and interdependent manner. To achieve reliability, organizations need to begin thinking about the relationship between these efforts and linking them conceptually. PMID:16898986

  17. The Stories Clinicians Tell: Achieving High Reliability and Improving Patient Safety

    PubMed Central

    Cohen, Daniel L; Stewart, Kevin O

    2016-01-01

    The patient safety movement has been deeply affected by the stories patients have shared that have identified numerous opportunities for improvements in safety. These stories have identified system and/or human inefficiencies or dysfunctions, possibly even failures, often resulting in patient harm. Although patients’ stories tell us much, less commonly heard are the stories of clinicians and how their personal observations regarding the environments they work in and the circumstances and pressures under which they work may degrade patient safety and lead to harm. If the health care industry is to function like a high-reliability industry, to improve its processes and achieve the outcomes that patients rightly deserve, then leaders and managers must seek and value input from those on the front lines—both clinicians and patients. Stories from clinicians provided in this article address themes that include incident identification, disclosure and transparency, just culture, the impact of clinical workload pressures, human factors liabilities, clinicians as secondary victims, the impact of disruptive and punitive behaviors, factors affecting professional morale, and personal failings. PMID:26580146

  18. Working Together to Achieve Greater Impact: The Donors' Education Collaborative of New York City. Principles for Effective Education Grantmaking. Case in Brief Number 3

    ERIC Educational Resources Information Center

    Grantmakers for Education, 2012

    2012-01-01

    Since the mid-1990s, constituency building and advocacy for better public education have grown steadily in New York City. "Working Together to Achieve Greater Impact" explores how that growth was fueled by the Donors' Education Collaborative of New York, which pools its members' financial resources and expertise to advance shared…

  19. Resource reliability, accessibility and governance: pillars for managing water resources to achieve water security in Nepal

    NASA Astrophysics Data System (ADS)

    Biggs, E. M.; Duncan, J.; Atkinson, P.; Dash, J.

    2013-12-01

    As one of the world's most water-abundant countries, Nepal has plenty of water yet resources are both spatially and temporally unevenly distributed. With a population heavily engaged in subsistence farming, whereby livelihoods are entirely dependent on rain-fed agriculture, changes in freshwater resources can substantially impact upon survival. The two main sources of water in Nepal come from monsoon precipitation and glacial runoff. The former is essential for sustaining livelihoods where communities have little or no access to perennial water resources. Much of Nepal's population live in the southern Mid-Hills and Terai regions where dependency on the monsoon system is high and climate-environment interactions are intricate. Any fluctuations in precipitation can severely affect essential potable resources and food security. As the population continues to expand in Nepal, and pressures build on access to adequate and clean water resources, there is a need for institutions to cooperate and increase the effectiveness of water management policies. This research presents a framework detailing three fundamental pillars for managing water resources to achieve sustainable water security in Nepal. These are (i) resource reliability; (ii) adequate accessibility; and (iii) effective governance. Evidence is presented which indicates that water resources are adequate in Nepal to sustain the population. In addition, aspects of climate change are having less impact than previously perceived e.g. results from trend analysis of precipitation time-series indicate a decrease in monsoon extremes and interannual variation over the last half-century. However, accessibility to clean water resources and the potential for water storage is limiting the use of these resources. This issue is particularly prevalent given the heterogeneity in spatial and temporal distributions of water. Water governance is also ineffective due to government instability and a lack of continuity in policy

  20. Updating the reference population to achieve constant genomic prediction reliability across generations.

    PubMed

    Pszczola, M; Calus, M P L

    2016-06-01

    The reliability of genomic breeding values (DGV) decays over generations. To keep the DGV reliability at a constant level, the reference population (RP) has to be continuously updated with animals from new generations. Updating RP may be challenging due to economic reasons, especially for novel traits involving expensive phenotyping. Therefore, the goal of this study was to investigate a minimal RP update size to keep the reliability at a constant level across generations. We used a simulated dataset resembling a dairy cattle population. The trait of interest was not included itself in the selection index, but it was affected by selection pressure by being correlated with an index trait that represented the overall breeding goal. The heritability of the index trait was assumed to be 0.25 and for the novel trait the heritability equalled 0.2. The genetic correlation between the two traits was 0.25. The initial RP (n=2000) was composed of cows only with a single observation per animal. Reliability of DGV using the initial RP was computed by evaluating contemporary animals. Thereafter, the RP was used to evaluate animals which were one generation younger from the reference individuals. The drop in the reliability when evaluating younger animals was then assessed and the RP was updated to re-gain the initial reliability. The update animals were contemporaries of evaluated animals (EVA). The RP was updated in batches of 100 animals/update. First, the animals most closely related to the EVA were chosen to update RP. The results showed that, approximately, 600 animals were needed every generation to maintain the DGV reliability at a constant level across generations. The sum of squared relationships between RP and EVA and the sum of off-diagonal coefficients of the inverse of the genomic relationship matrix for RP, separately explained 31% and 34%, respectively, of the variation in the reliability across generations. Combined, these parameters explained 53% of the

  1. Is It Really Possible to Test All Educationally Significant Achievements with High Levels of Reliability?

    ERIC Educational Resources Information Center

    Davis, Andrew

    2015-01-01

    PISA claims that it can extend its reach from its current core subjects of Reading, Science, Maths and problem-solving. Yet given the requirement for high levels of reliability for PISA, especially in the light of its current high stakes character, proposed widening of its subject coverage cannot embrace some important aspects of the social and…

  2. Reliability and Validity of the "Achievement Emotions Questionnaire": A Study of Argentinean University Students

    ERIC Educational Resources Information Center

    Paoloni, Paola Verónica; Vaja, Arabela Beatriz; Muñoz, Verónica Lilian

    2014-01-01

    Introduction: This paper aims at describing the psychometric features of the Achievement Emotions Questionnaire (AEQ), focusing specifically on the section that measures class emotions. From a theoretical perspective, this instrument was designed based on the control-value theory of achievement emotions. Therefore, a description of the…

  3. Laser welding of automotive aluminum alloys to achieve defect-free, structurally sound and reliable welds

    SciTech Connect

    DebRoy, T.

    2000-11-17

    The objective of this program was to seek improved process control and weldment reliability during laser welding of automotive aluminum alloys while retaining the high speed and accuracy of the laser beam welding process. The effects of various welding variables on the loss of alloying elements and the formation of porosity and other geometric weld defects such as underfill and overfill were studied both experimentally and theoretically.

  4. Reliability and Validity Evidence for Achievement Goal Models in High School Physical Education Settings

    ERIC Educational Resources Information Center

    Guan, Jianmin; McBride, Ron; Xiang, Ping

    2007-01-01

    Although empirical research in academic areas provides support for both a 3-factor as well as a 4-factor achievement goal model, both models were proposed and tested with a collegiate sample. Little is known about the generalizability of either model with high school level samples. This study was designed to examine whether the 3-factor model…

  5. The Achievement of Therapeutic Objectives Scale: Interrater Reliability and Sensitivity to Change in Short-Term Dynamic Psychotherapy and Cognitive Therapy

    ERIC Educational Resources Information Center

    Valen, Jakob; Ryum, Truls; Svartberg, Martin; Stiles, Tore C.; McCullough, Leigh

    2011-01-01

    This study examined interrater reliability and sensitivity to change of the Achievement of Therapeutic Objectives Scale (ATOS; McCullough, Larsen, et al., 2003) in short-term dynamic psychotherapy (STDP) and cognitive therapy (CT). The ATOS is a process scale originally developed to assess patients' achievements of treatment objectives in STDP,…

  6. Greater Expectations

    ERIC Educational Resources Information Center

    McCloskey, Patrick J.

    2006-01-01

    Julius Bennett was once a disinterested student destined to become a dropout. Then he enrolled in Amistad Academy, an academically focused charter middle school intent on narrowing the achievement gap between urban and suburban kids located in New Haven, Connecticut. Now Julius is making plans for college. In this article the author details the…

  7. Reliability and Validity Evidence of Scores on the Achievement Goal Tendencies Questionnaire in a Sample of Spanish Students of Compulsory Secondary Education

    ERIC Educational Resources Information Center

    Ingles, Candido J.; Garcia-Fernandez, Jose M.; Castejon, Juan L.; Valle, Antonio; Delgado, Beatriz; Marzo, Juan C.

    2009-01-01

    This study examined the reliability and validity evidence drawn from the scores of the Spanish version of the Achievement Goal Tendencies Questionnaire (AGTQ) using a sample of 2,022 (51.1% boys) Spanish students from grades 7 to 10. Confirmatory factor analysis replicated the correlated three-factor structure of the AGTQ in this sample: Learning…

  8. Greater years of maternal schooling and higher scores on academic achievement tests are independently associated with improved management of child diarrhea by rural Guatemalan mothers.

    PubMed

    Webb, Aimee L; Ramakrishnan, Usha; Stein, Aryeh D; Sellen, Daniel W; Merchant, Moeza; Martorell, Reynaldo

    2010-09-01

    Appropriate home management can alleviate many of the consequences of diarrhea including malnutrition, impaired development, growth faltering, and mortality. Maternal cognitive ability, years of schooling, and acquired academic skills are hypothesized to improve child health by improving maternal child care practices, such as illness management. Using information collected longitudinally in 1996-1999 from 466 rural Guatemalan women with children <36 months, we examined the independent associations between maternal years of schooling, academic skills, and scores on the Raven's Progressive Matrices and an illness management index (IMI). Women scoring in the lowest and middle tertiles of academic skills scored lower on the IMI compared to women in the highest tertile (-0.24 [95% CI: -0.54, 0.07]; -0.30 [95% CI: -0.54, -0.06], respectively) independent of sociodemographic factors, schooling, and Raven's scores. Among mothers with less than 1 year of schooling, scoring in the lowest tertile on the Raven's Progressive Matrices compared to the highest was significantly associated with scoring one point lower on the IMI (-1.18 [95% CI: -2.20, -0.17]). Greater academic skills were independently associated with maternal care during episodes of infant diarrhea. Schooling of young girls and/or community based programs that provide women with academic skills such as literacy, numeracy and knowledge could potentially improve mothers' care giving practices.

  9. WEF/WERF study of BNR plants achieving very low N and P limits: evaluation of technology performance and process reliability.

    PubMed

    Bott, Charles B; Parker, Denny S; Jimenez, Jose; Miller, Mark W; Neethling, J B

    2012-01-01

    The Water Environment Research Foundation (WERF) funded a two-year comprehensive study of nutrient removal plants designed and operated to meet very low effluent total nitrogen (TN) and total phosphorus (TP) concentrations. WERF worked with the Water Environment Federation (WEF) to solicit participation of volunteers and provide a forum for information exchange at workshops at its annual conferences. Both existing and new technologies are being adapted to meet requirements that are as low as 3.0 mg/L TN and 0.1 mg/L TP, and there is a need to define their capabilities and reliabilities in the real world situation of wastewater treatment plants. A concern over very low daily permits for ammonia caused the work to be extended to include nitrification reliability. This effort focused on maximizing what can be learned from existing technologies in order to provide a database that will inform key decision makers about proper choices for both technologies and rationale bases for statistical permit writing. To this end, managers of 22 plants, 10 achieving low effluent TP, nine achieving low effluent TN, and three achieving low effluent NH(3)-N, provided three years of operational data that were analyzed using a consistent statistical approach. Technology Performance Statistics (TPSs) were developed as three separate values representing the ideal, median, and reliably achievable performance. Technological conclusions can be drawn from the study in terms of what can be learned by comparing the different nutrient removal and nitrification processes employed at these 22 plants.

  10. Field-Induced Crystalline-to-Amorphous Phase Transformation on the Si Nano-Apex and the Achieving of Highly Reliable Si Nano-Cathodes

    PubMed Central

    Huang, Yifeng; Deng, Zexiang; Wang, Weiliang; Liang, Chaolun; She, Juncong; Deng, Shaozhi; Xu, Ningsheng

    2015-01-01

    Nano-scale vacuum channel transistors possess merits of higher cutoff frequency and greater gain power as compared with the conventional solid-state transistors. The improvement in cathode reliability is one of the major challenges to obtain high performance vacuum channel transistors. We report the experimental findings and the physical insight into the field induced crystalline-to-amorphous phase transformation on the surface of the Si nano-cathode. The crystalline Si tip apex deformed to amorphous structure at a low macroscopic field (0.6~1.65 V/nm) with an ultra-low emission current (1~10 pA). First-principle calculation suggests that the strong electrostatic force exerting on the electrons in the surface lattices would take the account for the field-induced atomic migration that result in an amorphization. The arsenic-dopant in the Si surface lattice would increase the inner stress as well as the electron density, leading to a lower amorphization field. Highly reliable Si nano-cathodes were obtained by employing diamond like carbon coating to enhance the electron emission and thus decrease the surface charge accumulation. The findings are crucial for developing highly reliable Si-based nano-scale vacuum channel transistors and have the significance for future Si nano-electronic devices with narrow separation. PMID:25994377

  11. Computational methods for efficient structural reliability and reliability sensitivity analysis

    NASA Technical Reports Server (NTRS)

    Wu, Y.-T.

    1993-01-01

    This paper presents recent developments in efficient structural reliability analysis methods. The paper proposes an efficient, adaptive importance sampling (AIS) method that can be used to compute reliability and reliability sensitivities. The AIS approach uses a sampling density that is proportional to the joint PDF of the random variables. Starting from an initial approximate failure domain, sampling proceeds adaptively and incrementally with the goal of reaching a sampling domain that is slightly greater than the failure domain to minimize over-sampling in the safe region. Several reliability sensitivity coefficients are proposed that can be computed directly and easily from the above AIS-based failure points. These probability sensitivities can be used for identifying key random variables and for adjusting design to achieve reliability-based objectives. The proposed AIS methodology is demonstrated using a turbine blade reliability analysis problem.

  12. Reliability training

    NASA Technical Reports Server (NTRS)

    Lalli, Vincent R. (Editor); Malec, Henry A. (Editor); Dillard, Richard B.; Wong, Kam L.; Barber, Frank J.; Barina, Frank J.

    1992-01-01

    Discussed here is failure physics, the study of how products, hardware, software, and systems fail and what can be done about it. The intent is to impart useful information, to extend the limits of production capability, and to assist in achieving low cost reliable products. A review of reliability for the years 1940 to 2000 is given. Next, a review of mathematics is given as well as a description of what elements contribute to product failures. Basic reliability theory and the disciplines that allow us to control and eliminate failures are elucidated.

  13. A Study to Determine Certain Characteristics of Earth Science Curriculum Project Teachers and Students in the Permissive or Authoritarian Classrooms which Lead to Greater Academic Achievement in These Students.

    ERIC Educational Resources Information Center

    Sargent, Earl Alvin

    Investigated was academic achievement of Earth Science Curriculum Project (ESCP) students in permissive and authoritarian classes. Authoritarian and permissive teachers were identified in the formal ESCP program using McGee's F-Scale; Form 30. Random samples of students and teachers were chosen from the 15 test centers throughout the United…

  14. Greater trochanteric pain syndrome.

    PubMed

    Strauss, Eric J; Nho, Shane J; Kelly, Bryan T

    2010-06-01

    Originally defined as "tenderness to palpation over the greater trochanter with the patient in the side-lying position," greater trochanteric pain syndrome (GTPS) as a clinical entity, has expanded to include a number of disorders of the lateral, peritrochanteric space of the hip, including trochanteric bursitis, tears of the gluteus medius and minimus and external coxa saltans (snapping hip). Typically presenting with pain and reproducible tenderness in the region of the greater trochanter, buttock, or lateral thigh, GTPS is relatively common, reported to affect between 10% and 25% of the general population. Secondary to the relative paucity of information available on the diagnosis and management of components of GTPS, the presence of these pathologic entities may be underrecognized, leading to extensive workups and delays in appropriate treatment. This article aims to review the present understanding of the lesions that comprise GTPS, discussing the relevant anatomy, diagnostic workup and recommended treatment for trochanteric bursitis, gluteus medius and minimus tears, and external coxa saltans.

  15. Assuring reliability program effectiveness.

    NASA Technical Reports Server (NTRS)

    Ball, L. W.

    1973-01-01

    An attempt is made to provide simple identification and description of techniques that have proved to be most useful either in developing a new product or in improving reliability of an established product. The first reliability task is obtaining and organizing parts failure rate data. Other tasks are parts screening, tabulation of general failure rates, preventive maintenance, prediction of new product reliability, and statistical demonstration of achieved reliability. Five principal tasks for improving reliability involve the physics of failure research, derating of internal stresses, control of external stresses, functional redundancy, and failure effects control. A final task is the training and motivation of reliability specialist engineers.

  16. [Greater trochanteric pain syndrome].

    PubMed

    Gollwitzer, H; Opitz, G; Gerdesmeyer, L; Hauschild, M

    2014-01-01

    Greater trochanteric pain is one of the common complaints in orthopedics. Frequent diagnoses include myofascial pain, trochanteric bursitis, tendinosis and rupture of the gluteus medius and minimus tendon, and external snapping hip. Furthermore, nerve entrapment like the piriformis syndrome must be considered in the differential diagnosis. This article summarizes essential diagnostic and therapeutic steps in greater trochanteric pain syndrome. Careful clinical evaluation, complemented with specific imaging studies and diagnostic infiltrations allows determination of the underlying pathology in most cases. Thereafter, specific nonsurgical treatment is indicated, with success rates of more than 90 %. Resistant cases and tendon ruptures may require surgical intervention, which can provide significant pain relief and functional improvement in most cases.

  17. [Autoerotic fatalities in Greater Dusseldorf].

    PubMed

    Hartung, Benno; Hellen, Florence; Borchard, Nora; Huckenbeck, Wolfgang

    2011-01-01

    Autoerotic fatalities in the Greater Dusseldorf area correspond to the relevant medicolegal literature. Our results included exclusively young to middle-aged, usually single men who were found dead in their city apartments. Clothing and devices used showed a great variety. Women's or fetish clothing and complex shackling or hanging devices were disproportionately frequent. In most cases, death occurred due to hanging or ligature strangulation. There was no increased incidence of underlying psychiatric disorders. In most of the deceased no or at least no remarkable alcohol intoxication was found. Occasionally, it may be difficult to reliably differentiate autoerotic accidents, accidents occurring in connection with practices of bondage & discipline, dominance & submission (BDSM) from natural death, suicide or homicide.

  18. Hawaii electric system reliability.

    SciTech Connect

    Silva Monroy, Cesar Augusto; Loose, Verne William

    2012-09-01

    This report addresses Hawaii electric system reliability issues; greater emphasis is placed on short-term reliability but resource adequacy is reviewed in reference to electric consumers' views of reliability %E2%80%9Cworth%E2%80%9D and the reserve capacity required to deliver that value. The report begins with a description of the Hawaii electric system to the extent permitted by publicly available data. Electrical engineering literature in the area of electric reliability is researched and briefly reviewed. North American Electric Reliability Corporation standards and measures for generation and transmission are reviewed and identified as to their appropriateness for various portions of the electric grid and for application in Hawaii. Analysis of frequency data supplied by the State of Hawaii Public Utilities Commission is presented together with comparison and contrast of performance of each of the systems for two years, 2010 and 2011. Literature tracing the development of reliability economics is reviewed and referenced. A method is explained for integrating system cost with outage cost to determine the optimal resource adequacy given customers' views of the value contributed by reliable electric supply. The report concludes with findings and recommendations for reliability in the State of Hawaii.

  19. Hawaii Electric System Reliability

    SciTech Connect

    Loose, Verne William; Silva Monroy, Cesar Augusto

    2012-08-01

    This report addresses Hawaii electric system reliability issues; greater emphasis is placed on short-term reliability but resource adequacy is reviewed in reference to electric consumers’ views of reliability “worth” and the reserve capacity required to deliver that value. The report begins with a description of the Hawaii electric system to the extent permitted by publicly available data. Electrical engineering literature in the area of electric reliability is researched and briefly reviewed. North American Electric Reliability Corporation standards and measures for generation and transmission are reviewed and identified as to their appropriateness for various portions of the electric grid and for application in Hawaii. Analysis of frequency data supplied by the State of Hawaii Public Utilities Commission is presented together with comparison and contrast of performance of each of the systems for two years, 2010 and 2011. Literature tracing the development of reliability economics is reviewed and referenced. A method is explained for integrating system cost with outage cost to determine the optimal resource adequacy given customers’ views of the value contributed by reliable electric supply. The report concludes with findings and recommendations for reliability in the State of Hawaii.

  20. Person Reliability

    ERIC Educational Resources Information Center

    Lumsden, James

    1977-01-01

    Person changes can be of three kinds: developmental trends, swells, and tremors. Person unreliability in the tremor sense (momentary fluctuations) can be estimated from person characteristic curves. Average person reliability for groups can be compared from item characteristic curves. (Author)

  1. Reliability Engineering Handbook

    DTIC Science & Technology

    1964-06-01

    INTEVAL 00 0 542 917 1953 OPERATING TIME IN HOURS Figure 6-4. TWT Reliability Function, Showing the 90% Confidence Interval 6-7 6-2-4 to 6-2-5 NAVWEPS...the lower one-sided 90% greater than 977 hours, or 90% confidence confidence limit on 0 is (.704)(530) = 373 that 0 lies between these two bounds . R...6-4 6-2-2 Measurement of Reliability (Application of Confidence Limits).. 6-4 6-2-3 Procedural Steps

  2. Reliability physics

    NASA Technical Reports Server (NTRS)

    Cuddihy, E. F.; Ross, R. G., Jr.

    1984-01-01

    Speakers whose topics relate to the reliability physics of solar arrays are listed and their topics briefly reviewed. Nine reports are reviewed ranging in subjects from studies of photothermal degradation in encapsulants and polymerizable ultraviolet stabilizers to interface bonding stability to electrochemical degradation of photovoltaic modules.

  3. Multidisciplinary System Reliability Analysis

    NASA Technical Reports Server (NTRS)

    Mahadevan, Sankaran; Han, Song; Chamis, Christos C. (Technical Monitor)

    2001-01-01

    The objective of this study is to develop a new methodology for estimating the reliability of engineering systems that encompass multiple disciplines. The methodology is formulated in the context of the NESSUS probabilistic structural analysis code, developed under the leadership of NASA Glenn Research Center. The NESSUS code has been successfully applied to the reliability estimation of a variety of structural engineering systems. This study examines whether the features of NESSUS could be used to investigate the reliability of systems in other disciplines such as heat transfer, fluid mechanics, electrical circuits etc., without considerable programming effort specific to each discipline. In this study, the mechanical equivalence between system behavior models in different disciplines are investigated to achieve this objective. A new methodology is presented for the analysis of heat transfer, fluid flow, and electrical circuit problems using the structural analysis routines within NESSUS, by utilizing the equivalence between the computational quantities in different disciplines. This technique is integrated with the fast probability integration and system reliability techniques within the NESSUS code, to successfully compute the system reliability of multidisciplinary systems. Traditional as well as progressive failure analysis methods for system reliability estimation are demonstrated, through a numerical example of a heat exchanger system involving failure modes in structural, heat transfer and fluid flow disciplines.

  4. Bison in the greater Yellowstone

    USGS Publications Warehouse

    Meagher, Mary

    1994-01-01

    In the Greater Yellowstone Area, free-ranging bison occur in Jackson Hole, Wyoming, and Yellowstone National Park. The Yellowstone population is discussed, with emphasis on changes in numbers from approximately 400 in 1968 to about 3500 now. Major influences for change initially were natural; more recently the winter road system used by snowmobiles appeared to be the dominant factor. The situation is in a state of flux. Interagency planning is in progress to address management alternatives for conflicts outside the park.

  5. Network reliability

    NASA Technical Reports Server (NTRS)

    Johnson, Marjory J.

    1985-01-01

    Network control (or network management) functions are essential for efficient and reliable operation of a network. Some control functions are currently included as part of the Open System Interconnection model. For local area networks, it is widely recognized that there is a need for additional control functions, including fault isolation functions, monitoring functions, and configuration functions. These functions can be implemented in either a central or distributed manner. The Fiber Distributed Data Interface Medium Access Control and Station Management protocols provide an example of distributed implementation. Relative information is presented here in outline form.

  6. Teamwork as an essential component of high-reliability organizations.

    PubMed

    Baker, David P; Day, Rachel; Salas, Eduardo

    2006-08-01

    Organizations are increasingly becoming dynamic and unstable. This evolution has given rise to greater reliance on teams and increased complexity in terms of team composition, skills required, and degree of risk involved. High-reliability organizations (HROs) are those that exist in such hazardous environments where the consequences of errors are high, but the occurrence of error is extremely low. In this article, we argue that teamwork is an essential component of achieving high reliability particularly in health care organizations. We describe the fundamental characteristics of teams, review strategies in team training, demonstrate the criticality of teamwork in HROs and finally, identify specific challenges the health care community must address to improve teamwork and enhance reliability.

  7. Increasing Male Academic Achievement

    ERIC Educational Resources Information Center

    Jackson, Barbara Talbert

    2008-01-01

    The No Child Left Behind legislation has brought greater attention to the academic performance of American youth. Its emphasis on student achievement requires a closer analysis of assessment data by school districts. To address the findings, educators must seek strategies to remedy failing results. In a mid-Atlantic district of the Unites States,…

  8. Reliability of plantar pressure platforms.

    PubMed

    Hafer, Jocelyn F; Lenhoff, Mark W; Song, Jinsup; Jordan, Joanne M; Hannan, Marian T; Hillstrom, Howard J

    2013-07-01

    Plantar pressure measurement is common practice in many research and clinical protocols. While the accuracy of some plantar pressure measuring devices and methods for ensuring consistency in data collection on plantar pressure measuring devices have been reported, the reliability of different devices when testing the same individuals is not known. This study calculated intra-mat, intra-manufacturer, and inter-manufacturer reliability of plantar pressure parameters as well as the number of plantar pressure trials needed to reach a stable estimate of the mean for an individual. Twenty-two healthy adults completed ten walking trials across each of two Novel emed-x(®) and two Tekscan MatScan(®) plantar pressure measuring devices in a single visit. Intraclass correlation (ICC) was used to describe the agreement between values measured by different devices. All intra-platform reliability correlations were greater than 0.70. All inter-emed-x(®) reliability correlations were greater than 0.70. Inter-MatScan(®) reliability correlations were greater than 0.70 in 31 and 52 of 56 parameters when looking at a 10-trial average and a 5-trial average, respectively. Inter-manufacturer reliability including all four devices was greater than 0.70 for 52 and 56 of 56 parameters when looking at a 10-trial average and a 5-trial average, respectively. All parameters reached a value within 90% of an unbiased estimate of the mean within five trials. Overall, reliability results are encouraging for investigators and clinicians who may have plantar pressure data sets that include data collected on different devices.

  9. Reliable VLSI sequential controllers

    NASA Technical Reports Server (NTRS)

    Whitaker, S.; Maki, G.; Shamanna, M.

    1990-01-01

    A VLSI architecture for synchronous sequential controllers is presented that has attractive qualities for producing reliable circuits. In these circuits, one hardware implementation can realize any flow table with a maximum of 2(exp n) internal states and m inputs. Also all design equations are identical. A real time fault detection means is presented along with a strategy for verifying the correctness of the checking hardware. This self check feature can be employed with no increase in hardware. The architecture can be modified to achieve fail safe designs. With no increase in hardware, an adaptable circuit can be realized that allows replacement of faulty transitions with fault free transitions.

  10. Integrated modular engine - Reliability assessment

    NASA Astrophysics Data System (ADS)

    Parsley, R. C.; Ward, T. B.

    1992-07-01

    A major driver in the increased interest in integrated modular engine configurations is the desire for ultra reliability for future rocket propulsion systems. The concept of configuring multiple sets of turbomachinery networked to multiple thrust chamber assemblies has been identified as an approach with potential to achieve significant reliability enhancement. This paper summarizes the results of a reliability study comparing networked systems vs. discrete engine installations, both with and without major module and engine redundancy. The study was conducted for gas generator, expander, and staged combustion cycles. The results are representative of either booster or upper-stage applications and are indicative of either plug or nonplug installation philosophies.

  11. Robust fusion with reliabilities weights

    NASA Astrophysics Data System (ADS)

    Grandin, Jean-Francois; Marques, Miguel

    2002-03-01

    The reliability is a value of the degree of trust in a given measurement. We analyze and compare: ML (Classical Maximum Likelihood), MLE (Maximum Likelihood weighted by Entropy), MLR (Maximum Likelihood weighted by Reliability), MLRE (Maximum Likelihood weighted by Reliability and Entropy), DS (Credibility Plausibility), DSR (DS weighted by reliabilities). The analysis is based on a model of a dynamical fusion process. It is composed of three sensors, which have each it's own discriminatory capacity, reliability rate, unknown bias and measurement noise. The knowledge of uncertainties is also severely corrupted, in order to analyze the robustness of the different fusion operators. Two sensor models are used: the first type of sensor is able to estimate the probability of each elementary hypothesis (probabilistic masses), the second type of sensor delivers masses on union of elementary hypotheses (DS masses). In the second case probabilistic reasoning leads to sharing the mass abusively between elementary hypotheses. Compared to the classical ML or DS which achieves just 50% of correct classification in some experiments, DSR, MLE, MLR and MLRE reveals very good performances on all experiments (more than 80% of correct classification rate). The experiment was performed with large variations of the reliability coefficients for each sensor (from 0 to 1), and with large variations on the knowledge of these coefficients (from 0 0.8). All four operators reveal good robustness, but the MLR reveals to be uniformly dominant on all the experiments in the Bayesian case and achieves the best mean performance under incomplete a priori information.

  12. Reliability and Maintainability (RAM) Training

    NASA Technical Reports Server (NTRS)

    Lalli, Vincent R. (Editor); Malec, Henry A. (Editor); Packard, Michael H. (Editor)

    2000-01-01

    The theme of this manual is failure physics-the study of how products, hardware, software, and systems fail and what can be done about it. The intent is to impart useful information, to extend the limits of production capability, and to assist in achieving low-cost reliable products. In a broader sense the manual should do more. It should underscore the urgent need CI for mature attitudes toward reliability. Five of the chapters were originally presented as a classroom course to over 1000 Martin Marietta engineers and technicians. Another four chapters and three appendixes have been added, We begin with a view of reliability from the years 1940 to 2000. Chapter 2 starts the training material with a review of mathematics and a description of what elements contribute to product failures. The remaining chapters elucidate basic reliability theory and the disciplines that allow us to control and eliminate failures.

  13. Reliability model generator

    NASA Technical Reports Server (NTRS)

    McMann, Catherine M. (Inventor); Cohen, Gerald C. (Inventor)

    1991-01-01

    An improved method and system for automatically generating reliability models for use with a reliability evaluation tool is described. The reliability model generator of the present invention includes means for storing a plurality of low level reliability models which represent the reliability characteristics for low level system components. In addition, the present invention includes means for defining the interconnection of the low level reliability models via a system architecture description. In accordance with the principles of the present invention, a reliability model for the entire system is automatically generated by aggregating the low level reliability models based on the system architecture description.

  14. Reliability Considerations for the Operation of Large Accelerator User Facilities

    SciTech Connect

    Willeke, F. J.

    2016-01-29

    The lecture provides an overview of considerations relevant for achieving highly reliable operation of accelerator based user facilities. The article starts with an overview of statistical reliability formalism which is followed by high reliability design considerations with examples. Finally, the article closes with operational aspects of high reliability such as preventive maintenance and spares inventory.

  15. Epistemological Beliefs and Academic Achievement

    ERIC Educational Resources Information Center

    Arslantas, Halis Adnan

    2016-01-01

    This study aimed to identify the relationship between teacher candidates' epistemological beliefs and academic achievement. The participants of the study were 353 teacher candidates studying their fourth year at the Education Faculty. The Epistemological Belief Scale was used which adapted to Turkish through reliability and validity work by…

  16. Sharing Leadership Responsibilities Results in Achievement Gains

    ERIC Educational Resources Information Center

    Armistead, Lew

    2010-01-01

    Collective, not individual, leadership in schools has a greater impact on student achievement; when principals and teachers share leadership responsibilities, student achievement is higher; and schools having high student achievement also display a vision for student achievement and teacher growth. Those are just a few of the insights into school…

  17. Reliability Generalization: "Lapsus Linguae"

    ERIC Educational Resources Information Center

    Smith, Julie M.

    2011-01-01

    This study examines the proposed Reliability Generalization (RG) method for studying reliability. RG employs the application of meta-analytic techniques similar to those used in validity generalization studies to examine reliability coefficients. This study explains why RG does not provide a proper research method for the study of reliability,…

  18. Treatment of symptomatic greater trochanteric fracture after total hip arthroplasty.

    PubMed

    Peretz, Jeffrey I; Chuang, Michael J; Cerynik, Douglas L; Johanson, Norman A

    2009-08-01

    Isolated greater trochanter fractures after total hip arthroplasty are associated with major comorbidities such as debilitating weakness, pain, and dislocation. No definitive standard of care has been established for these fracture. However, it is well known that reestablishing osseous union in these patients is strongly associated with return of functional status. We report a case of an elderly patient with multiple hip revision surgeries now presenting with unilateral greater trochanter fracture. Treatment incorporated the use of a trochanteric claw plate, cerclage wiring, and adjuvant demineralized bone matrix allograft to achieve successful osseous union. This is the first reported use of adjuvant demineralized bone matrix for fixing these fractures.

  19. Can There Be Reliability without "Reliability?"

    ERIC Educational Resources Information Center

    Mislevy, Robert J.

    2004-01-01

    An "Educational Researcher" article by Pamela Moss (1994) asks the title question, "Can there be validity without reliability?" Yes, she answers, if by reliability one means "consistency among independent observations intended as interchangeable" (Moss, 1994, p. 7), quantified by internal consistency indices such as…

  20. Achieving Energy Efficiency Through Real-Time Feedback

    SciTech Connect

    Nesse, Ronald J.

    2011-09-01

    Through the careful implementation of simple behavior change measures, opportunities exist to achieve strategic gains, including greater operational efficiencies, energy cost savings, greater tenant health and ensuing productivity and an improved brand value through sustainability messaging and achievement.

  1. Greater trochanteric pain syndrome diagnosis and treatment.

    PubMed

    Mallow, Michael; Nazarian, Levon N

    2014-05-01

    Lateral hip pain, or greater trochanteric pain syndrome, is a commonly seen condition; in this article, the relevant anatomy, epidemiology, and evaluation strategies of greater trochanteric pain syndrome are reviewed. Specific attention is focused on imaging of this syndrome and treatment techniques, including ultrasound-guided interventions.

  2. Evaluating 'good governance': The development of a quantitative tool in the Greater Serengeti Ecosystem.

    PubMed

    Kisingo, Alex; Rollins, Rick; Murray, Grant; Dearden, Phil; Clarke, Marlea

    2016-10-01

    Protected areas (PAs) can provide important benefits to conservation and to communities. A key factor in the effective delivery of these benefits is the role of governance. There has been a growth in research developing frameworks to evaluate 'good' PA governance, usually drawing on a set of principles that are associated with groups of indicators. In contrast to dominant qualitative approaches, this paper describes the development of a quantitative method for measuring effectiveness of protected area governance, as perceived by stakeholders in the Greater Serengeti Ecosystem in Tanzania. The research developed a quantitative method for developing effectiveness measures of PA governance, using a set of 65 statements related to governance principles developed from a literature review. The instrument was administered to 389 individuals from communities located near PAs in the Greater Serengeti Ecosystem. The results of a factor analysis suggest that statements load onto 10 factors that demonstrate high psychometric validity as measured by factor loadings, explained variance, and Cronbach's alpha reliability. The ten common factors that were extracted were: 1) legitimacy, 2) transparency and accountability, 3) responsiveness, 4) fairness, 5) participation, 6) ecosystem based management (EBM) and connectivity, 7) resilience, 8) achievements, 9) consensus orientation, and 10) power. The paper concludes that quantitative surveys can be used to evaluate governance of protected areas from a community-level perspective.

  3. High-Reliability Computing For The Smarter Planet

    NASA Astrophysics Data System (ADS)

    Quinn, Heather; Manuzzato, Andrea; Graham, Paul; Dehon, Andre'; Carter, Nicholas

    2011-06-01

    As computer automation continues to increase in our society, the need for greater radiation reliability is necessary. Already critical infrastructure is failing too frequently. In this paper, we will introduce the Cross-Layer Reliability concept for designing more reliable computer systems.

  4. Identification and Analysis of the Alternatives for Achieving Greater Television Program Diversity in the United States.

    ERIC Educational Resources Information Center

    Dimling, John A., Jr.; And Others

    Several alternatives to the present television industry structure are considered in this study. They are: continuation of present policies, satellite-to-home broadcasting, and cable distribution of television. Trends noted are: the growth of commercial UHF (Ultra High Frequency) stations, the introduction of all-channel sets, population growth,…

  5. Achieving a Greater Impact: Developing the Skills of Teaching Artists to Lead Professional Development for Teachers

    ERIC Educational Resources Information Center

    Duma, Amy L.; Silverstein, Lynne B.

    2008-01-01

    Teaching artists know that there are many more students who could benefit from learning in and through the arts, but school budgets as well as teaching artists' time and energy are limited. As years pass, teaching artists face the reality that they will reach only a fraction of the students in need. To extend their impact dramatically, some…

  6. Genetic engineering of fungal biocontrol agents to achieve greater efficacy against insect pests.

    PubMed

    St Leger, Raymond J; Wang, Chengshu

    2010-01-01

    Molecular biology methods have elucidated pathogenic processes in several fungal biocontrol agents including two of the most commonly applied entomopathogenic fungi, Metarhizium anisopliae and Beauveria bassiana. In this review, we describe how a combination of molecular techniques has: (1) identified and characterized genes involved in infection; (2) manipulated the genes of the pathogen to improve biocontrol performance; and (3) allowed expression of a neurotoxin from the scorpion Androctonus australis. The complete sequencing of four exemplar species of entomopathogenic fungi including B. bassiana and M. anisopliae will be completed in 2010. Coverage of these genomes will help determine the identity, origin, and evolution of traits needed for diverse lifestyles and host switching. Such knowledge combined with the precision and malleability of molecular techniques will allow design of multiple pathogens with different strategies to be used for different ecosystems and avoid the possibility of the host developing resistance.

  7. Do Left or Right Brain Training Exercises Have the Greater Effect upon College Calculus Achievement?

    ERIC Educational Resources Information Center

    Miller, Cynthia A.

    Research supports the premise that various mathematical topics can be categorized as being performed better by the left or right brain hemisphere. This study examined the effect of left and right brain hemispheric lateralization exercises upon course grades in two sections of Analysis I (beginning calculus for mathematics/science majors) at a…

  8. Conscientiousness predicts greater recovery from negative emotion.

    PubMed

    Javaras, Kristin N; Schaefer, Stacey M; van Reekum, Carien M; Lapate, Regina C; Greischar, Lawrence L; Bachhuber, David R; Love, Gayle Dienberg; Ryff, Carol D; Davidson, Richard J

    2012-10-01

    Greater levels of conscientiousness have been associated with lower levels of negative affect. We focus on one mechanism through which conscientiousness may decrease negative affect: effective emotion regulation, as reflected by greater recovery from negative stimuli. In 273 adults who were 35-85 years old, we collected self-report measures of personality including conscientiousness and its self-control facet, followed on average 2 years later by psychophysiological measures of emotional reactivity and recovery. Among middle-aged adults (35-65 years old), the measures of conscientiousness and self-control predicted greater recovery from, but not reactivity to, negative emotional stimuli. The effect of conscientiousness and self-control on recovery was not driven by other personality variables or by greater task adherence on the part of high conscientiousness individuals. In addition, the effect was specific to negative emotional stimuli and did not hold for neutral or positive emotional stimuli.

  9. Reliability of neuroanatomical measurements in a multisite longitudinal study of youth at risk for psychosis.

    PubMed

    Cannon, Tyrone D; Sun, Frank; McEwen, Sarah Jacobson; Papademetris, Xenophon; He, George; van Erp, Theo G M; Jacobson, Aron; Bearden, Carrie E; Walker, Elaine; Hu, Xiaoping; Zhou, Lei; Seidman, Larry J; Thermenos, Heidi W; Cornblatt, Barbara; Olvet, Doreen M; Perkins, Diana; Belger, Aysenil; Cadenhead, Kristin; Tsuang, Ming; Mirzakhanian, Heline; Addington, Jean; Frayne, Richard; Woods, Scott W; McGlashan, Thomas H; Constable, R Todd; Qiu, Maolin; Mathalon, Daniel H; Thompson, Paul; Toga, Arthur W

    2014-05-01

    Multisite longitudinal neuroimaging designs are used to identify differential brain structural change associated with onset or progression of disease. The reliability of neuroanatomical measurements over time and across sites is a crucial aspect of power in such studies. Prior work has found that while within-site reliabilities of neuroanatomical measurements are excellent, between-site reliability is generally more modest. Factors that may increase between-site reliability include standardization of scanner platform and sequence parameters and correction for between-scanner variations in gradient nonlinearities. Factors that may improve both between- and within-site reliability include use of registration algorithms that account for individual differences in cortical patterning and shape. In this study 8 healthy volunteers were scanned twice on successive days at 8 sites participating in the North American Prodrome Longitudinal Study (NAPLS). All sites employed 3 Tesla scanners and standardized acquisition parameters. Site accounted for 2 to 30% of the total variance in neuroanatomical measurements. However, site-related variations were trivial (<1%) among sites using the same scanner model and 12-channel coil or when correcting for between-scanner differences in gradient nonlinearity and scaling. Adjusting for individual differences in sulcal-gyral geometries yielded measurements with greater reliabilities than those obtained using an automated approach. Neuroimaging can be performed across multiple sites at the same level of reliability as at a single site, achieving within- and between-site reliabilities of 0.95 or greater for gray matter density in the majority of voxels in the prefrontal and temporal cortical surfaces as well as for the volumes of most subcortical structures.

  10. Highly reliable multisensor array (MSA) smart transducers

    NASA Astrophysics Data System (ADS)

    Perotti, José; Lucena, Angel; Mackey, Paul; Mata, Carlos; Immer, Christopher

    2006-05-01

    Many developments in the field of multisensor array (MSA) transducers have taken place in the last few years. Advancements in fabrication technology, such as Micro-Electro-Mechanical Systems (MEMS) and nanotechnology, have made implementation of MSA devices a reality. NASA Kennedy Space Center (KSC) has been developing this type of technology because of the increases in safety, reliability, and performance and the reduction in operational and maintenance costs that can be achieved with these devices. To demonstrate the MSA technology benefits, KSC quantified the relationship between the number of sensors (N) and the associated improvement in sensor life and reliability. A software algorithm was developed to monitor and assess the health of each element and the overall MSA. Furthermore, the software algorithm implemented criteria on how these elements would contribute to the MSA-calculated output to ensure required performance. The hypothesis was that a greater number of statistically independent sensor elements would provide a measurable increase in measurement reliability. A computer simulation was created to answer this question. An array of N sensors underwent random failures in the simulation and a life extension factor (LEF equals the percentage of the life of a single sensor) was calculated by the program. When LEF was plotted as a function of N, a quasiexponential behavior was detected with marginal improvement above N = 30. The hypothesis and follow-on simulation results were then corroborated experimentally. An array composed of eight independent pressure sensors was fabricated. To accelerate sensor life cycle and failure and to simulate degradation over time, the MSA was exposed to an environmental tem-perature of 125°C. Every 24 hours, the experiment's environmental temperature was returned to ambient temperature (27°C), and the outputs of all the MSA sensor elements were measured. Once per week, the MSA calibration was verified at five different

  11. Power electronics reliability analysis.

    SciTech Connect

    Smith, Mark A.; Atcitty, Stanley

    2009-12-01

    This report provides the DOE and industry with a general process for analyzing power electronics reliability. The analysis can help with understanding the main causes of failures, downtime, and cost and how to reduce them. One approach is to collect field maintenance data and use it directly to calculate reliability metrics related to each cause. Another approach is to model the functional structure of the equipment using a fault tree to derive system reliability from component reliability. Analysis of a fictitious device demonstrates the latter process. Optimization can use the resulting baseline model to decide how to improve reliability and/or lower costs. It is recommended that both electric utilities and equipment manufacturers make provisions to collect and share data in order to lay the groundwork for improving reliability into the future. Reliability analysis helps guide reliability improvements in hardware and software technology including condition monitoring and prognostics and health management.

  12. Human Reliability Program Overview

    SciTech Connect

    Bodin, Michael

    2012-09-25

    This presentation covers the high points of the Human Reliability Program, including certification/decertification, critical positions, due process, organizational structure, program components, personnel security, an overview of the US DOE reliability program, retirees and academia, and security program integration.

  13. Integrated avionics reliability

    NASA Technical Reports Server (NTRS)

    Alikiotis, Dimitri

    1988-01-01

    The integrated avionics reliability task is an effort to build credible reliability and/or performability models for multisensor integrated navigation and flight control. The research was initiated by the reliability analysis of a multisensor navigation system consisting of the Global Positioning System (GPS), the Long Range Navigation system (Loran C), and an inertial measurement unit (IMU). Markov reliability models were developed based on system failure rates and mission time.

  14. Reliable Design Versus Trust

    NASA Technical Reports Server (NTRS)

    Berg, Melanie; LaBel, Kenneth A.

    2016-01-01

    This presentation focuses on reliability and trust for the users portion of the FPGA design flow. It is assumed that the manufacturer prior to hand-off to the user tests FPGA internal components. The objective is to present the challenges of creating reliable and trusted designs. The following will be addressed: What makes a design vulnerable to functional flaws (reliability) or attackers (trust)? What are the challenges for verifying a reliable design versus a trusted design?

  15. Reliability and structural integrity

    NASA Technical Reports Server (NTRS)

    Davidson, J. R.

    1976-01-01

    An analytic model is developed to calculate the reliability of a structure after it is inspected for cracks. The model accounts for the growth of undiscovered cracks between inspections and their effect upon the reliability after subsequent inspections. The model is based upon a differential form of Bayes' Theorem for reliability, and upon fracture mechanics for crack growth.

  16. Reliability model generator specification

    NASA Technical Reports Server (NTRS)

    Cohen, Gerald C.; Mccann, Catherine

    1990-01-01

    The Reliability Model Generator (RMG), a program which produces reliability models from block diagrams for ASSIST, the interface for the reliability evaluation tool SURE is described. An account is given of motivation for RMG and the implemented algorithms are discussed. The appendices contain the algorithms and two detailed traces of examples.

  17. Viking Lander reliability program

    NASA Technical Reports Server (NTRS)

    Pilny, M. J.

    1978-01-01

    The Viking Lander reliability program is reviewed with attention given to the development of the reliability program requirements, reliability program management, documents evaluation, failure modes evaluation, production variation control, failure reporting and correction, and the parts program. Lander hardware failures which have occurred during the mission are listed.

  18. Theory of reliable systems

    NASA Technical Reports Server (NTRS)

    Meyer, J. F.

    1975-01-01

    An attempt was made to refine the current notion of system reliability by identifying and investigating attributes of a system which are important to reliability considerations. Techniques which facilitate analysis of system reliability are included. Special attention was given to fault tolerance, diagnosability, and reconfigurability characteristics of systems.

  19. Predicting software reliability

    NASA Technical Reports Server (NTRS)

    Littlewood, B.

    1989-01-01

    A detailed look is given to software reliability techniques. A conceptual model of the failure process is examined, and some software reliability growth models are discussed. Problems for which no current solutions exist are addressed, emphasizing the very difficult problem of safety-critical systems for which the reliability requirements can be enormously demanding.

  20. Kepler Reliability and Occurrence Rates

    NASA Astrophysics Data System (ADS)

    Bryson, Steve

    2016-10-01

    The Kepler mission has produced tables of exoplanet candidates (``KOI table''), as well as tables of transit detections (``TCE table''), hosted at the Exoplanet Archive (http://exoplanetarchive.ipac.caltech.edu). Transit detections in the TCE table that are plausibly due to a transiting object are selected for inclusion in the KOI table. KOI table entries that have not been identified as false positives (FPs) or false alarms (FAs) are classified as planet candidates (PCs, Mullally et al. 2015). A subset of PCs have been confirmed as planetary transits with greater than 99% probability, but most PCs have <99% probability of being true planets. The fraction of PCs that are true transiting planets is the PC reliability rate. The overall PC population is believed to have a reliability rate >90% (Morton & Johnson 2011).

  1. Reliability assurance for regulation of advanced reactors

    SciTech Connect

    Fullwood, R.; Lofaro, R.; Samanta, P.

    1991-12-31

    The advanced nuclear power plants must achieve higher levels of safety than the first generation of plants. Showing that this is indeed true provides new challenges to reliability and risk assessment methods in the analysis of the designs employing passive and semi-passive protection. Reliability assurance of the advanced reactor systems is important for determining the safety of the design and for determining the plant operability. Safety is the primary concern, but operability is considered indicative of good and safe operation. This paper discusses several concerns for reliability assurance of the advanced design encompassing reliability determination, level of detail required in advanced reactor submittals, data for reliability assurance, systems interactions and common cause effects, passive component reliability, PRA-based configuration control system, and inspection, training, maintenance and test requirements. Suggested approaches are provided for addressing each of these topics.

  2. Creating Highly Reliable Accountable Care Organizations.

    PubMed

    Vogus, Timothy J; Singer, Sara J

    2016-12-01

    Accountable Care Organizations' (ACOs) pursuit of the triple aim of higher quality, lower cost, and improved population health has met with mixed results. To improve the design and implementation of ACOs we look to organizations that manage similarly complex, dynamic, and tightly coupled conditions while sustaining exceptional performance known as high-reliability organizations. We describe the key processes through which organizations achieve reliability, the leadership and organizational practices that enable it, and the role that professionals can play when charged with enacting it. Specifically, we present concrete practices and processes from health care organizations pursuing high-reliability and from early ACOs to illustrate how the triple aim may be met by cultivating mindful organizing, practicing reliability-enhancing leadership, and identifying and supporting reliability professionals. We conclude by proposing a set of research questions to advance the study of ACOs and high-reliability research.

  3. PV Systems Reliability Final Technical Report.

    SciTech Connect

    Lavrova, Olga; Flicker, Jack David; Johnson, Jay; Armijo, Kenneth Miguel; Gonzalez, Sigifredo; Schindelholz, Eric John; Sorensen, Neil R.; Yang, Benjamin Bing-Yeh

    2015-12-01

    The continued exponential growth of photovoltaic technologies paves a path to a solar-powered world, but requires continued progress toward low-cost, high-reliability, high-performance photovoltaic (PV) systems. High reliability is an essential element in achieving low-cost solar electricity by reducing operation and maintenance (O&M) costs and extending system lifetime and availability, but these attributes are difficult to verify at the time of installation. Utilities, financiers, homeowners, and planners are demanding this information in order to evaluate their financial risk as a prerequisite to large investments. Reliability research and development (R&D) is needed to build market confidence by improving product reliability and by improving predictions of system availability, O&M cost, and lifetime. This project is focused on understanding, predicting, and improving the reliability of PV systems. The two areas being pursued include PV arc-fault and ground fault issues, and inverter reliability.

  4. Accessibility, reliability, and usability of neurosurgical resources.

    PubMed

    Agarwal, Nitin; Kommana, Sumana S; Hansberry, David R; Kashkoush, Ahmed I; Friedlander, Robert M; Lunsford, L Dade

    2017-04-01

    OBJECTIVE Closing the knowledge gap that exists between patients and health care providers is essential and is facilitated by easy access to patient education materials. Although such information has the potential to be an effective resource, it must be written in a user-friendly and understandable manner, especially when such material pertains to specialized and highly technical fields such as neurological surgery. The authors evaluated the accessibility, usability, and reliability of current educational resources provided by the American Association of Neurological Surgeons (AANS), Healthwise, and the National Institute for Neurological Disorders and Stroke (NINDS). METHODS Online neurosurgical patient education information provided by AANS, Healthwise, and NINDS was evaluated using the LIDA scale, a website quality assessment tool, by medical professionals and nonmedical professionals. A high achieving score is regarded as 90% or greater using the LIDA scale. RESULTS Accessibility scores were 76.7% (AANS), 83.3% (Healthwise), and 75.0% (NINDS). Average usability scores for the AANS, Healthwise, and NINDS were 73.3%, 82.6%, and 82.9%, respectively, when evaluated by medical professionals and 78.5%, 80.7%, and 75.9%, respectively, for nonmedical professionals, respectively. Average reliability scores were 58.5%, 53.3%, 72.6%, respectively, for medical professionals and 70.4%, 66.7%, and 78.5%, respectively, for nonmedical professionals when evaluating the AANS, Healthwise, and NINDS websites. CONCLUSIONS Although organizations like AANS, Healthwise, and NINDS should be commended for their ongoing commitment to provide health care-oriented materials, modification of this material is suggested to improve the patient education value.

  5. Human Reliability Analysis for Design: Using Reliability Methods for Human Factors Issues

    SciTech Connect

    Ronald Laurids Boring

    2010-11-01

    This paper reviews the application of human reliability analysis methods to human factors design issues. An application framework is sketched in which aspects of modeling typically found in human reliability analysis are used in a complementary fashion to the existing human factors phases of design and testing. The paper provides best achievable practices for design, testing, and modeling. Such best achievable practices may be used to evaluate and human system interface in the context of design safety certifications.

  6. Greater Sao Paulo Newer Library Automation.

    ERIC Educational Resources Information Center

    McLean, Dulce Didio

    1991-01-01

    This followup to a 1981 study presents descriptions of automated projects or activities in academic, public, and special libraries or information centers in the Greater Sao Paulo region that developed from 1981 through 1987. It is noted that an overall increase in the level of automation since 1981 has been observed. (four references) (Author/MAB)

  7. Paleotectonic and paleogeographic evolution of greater China

    SciTech Connect

    Yilmaz, P.O.; Norton, I.O. )

    1996-01-01

    In this study, we utilize plate tectonic history of Central Asia to constrain understanding of sedimentary basin development and to show how regional scale tectonic events affect play elements for major basins of greater China. Tectonic framework and paleogeography are used as a constraint on models for basin formation, climate distribution and accommodation which in turn control distribution of reservoir, source, seal and trap. Greater China is an artifact of Phanerozoic tectonics. It has a protracted history of continental deformation as amalgamation of crustal blocks and island arc/subduction and accretion complexes occurred. Early Paleozoic hydrocarbon systems are dominated by extensive carbonate platform and Permian and younger systems are dominated by continental and lacustrine sedimentation. The basement of greater China consists of continental and accretion crust. The crustal blocks include South and North China, Indochina, Tibet and Tarim, and accretion blocks include the Altaids and Manchurides. The relative positions and interactions of these blocks during Paleozic and Mesozoic time resulted in formation of greater China. Final amalgamation and deformation occurred in Eocene time when India collided with Asia. The discussions consist of presentation of a model for tectonic evolution of these blocks and their paleogeography through Phanerozoic time. This is done with maps at 1:8 million scale covering nine time slices, three in the Paleozoic, three in the Mesozoic and three in the Cenozoic.

  8. Spread of English across Greater China

    ERIC Educational Resources Information Center

    Feng, Anwei

    2012-01-01

    Greater China is used in this article to refer to mainland China, Hong Kong, Singapore, Taiwan and Macao. While a holistic approach is adopted to present and compare the rapid spread of English and development in English language education in these geographically close, and sociopolitically, culturally and economically interrelated but hugely…

  9. Waste Management in Greater Dhaka City.

    ERIC Educational Resources Information Center

    Rahman, M. H.

    1993-01-01

    This study focuses on the environmental degradation of Greater Dhaka City (GDC) resulting from pollution created by the indiscriminate disposal of industrial wastes, open dumping of solid wastes, inadequate treatment and disposal of domestic sewage, and unplanned disposal of leachate from agricultural land. Measures to protect the GDC environment…

  10. Six Motivational Reasons for Low School Achievement

    ERIC Educational Resources Information Center

    Reiss, Steven

    2009-01-01

    Reiss ("The normal personality: a new way of thinking about people." Cambridge University Press, New York, 2008) empirically derived a reliable and valid taxonomy of 16 life motives ("psychological needs"). The model suggests six motivational reasons for low achievement in school. Low achievement may be motivated by fear of failure (high need for…

  11. Software Reliability 2002

    NASA Technical Reports Server (NTRS)

    Wallace, Dolores R.

    2003-01-01

    In FY01 we learned that hardware reliability models need substantial changes to account for differences in software, thus making software reliability measurements more effective, accurate, and easier to apply. These reliability models are generally based on familiar distributions or parametric methods. An obvious question is 'What new statistical and probability models can be developed using non-parametric and distribution-free methods instead of the traditional parametric method?" Two approaches to software reliability engineering appear somewhat promising. The first study, begin in FY01, is based in hardware reliability, a very well established science that has many aspects that can be applied to software. This research effort has investigated mathematical aspects of hardware reliability and has identified those applicable to software. Currently the research effort is applying and testing these approaches to software reliability measurement, These parametric models require much project data that may be difficult to apply and interpret. Projects at GSFC are often complex in both technology and schedules. Assessing and estimating reliability of the final system is extremely difficult when various subsystems are tested and completed long before others. Parametric and distribution free techniques may offer a new and accurate way of modeling failure time and other project data to provide earlier and more accurate estimates of system reliability.

  12. Recalibrating software reliability models

    NASA Technical Reports Server (NTRS)

    Brocklehurst, Sarah; Chan, P. Y.; Littlewood, Bev; Snell, John

    1990-01-01

    In spite of much research effort, there is no universally applicable software reliability growth model which can be trusted to give accurate predictions of reliability in all circumstances. Further, it is not even possible to decide a priori which of the many models is most suitable in a particular context. In an attempt to resolve this problem, techniques were developed whereby, for each program, the accuracy of various models can be analyzed. A user is thus enabled to select that model which is giving the most accurate reliability predicitons for the particular program under examination. One of these ways of analyzing predictive accuracy, called the u-plot, in fact allows a user to estimate the relationship between the predicted reliability and the true reliability. It is shown how this can be used to improve reliability predictions in a completely general way by a process of recalibration. Simulation results show that the technique gives improved reliability predictions in a large proportion of cases. However, a user does not need to trust the efficacy of recalibration, since the new reliability estimates prodcued by the technique are truly predictive and so their accuracy in a particular application can be judged using the earlier methods. The generality of this approach would therefore suggest that it be applied as a matter of course whenever a software reliability model is used.

  13. Recalibrating software reliability models

    NASA Technical Reports Server (NTRS)

    Brocklehurst, Sarah; Chan, P. Y.; Littlewood, Bev; Snell, John

    1989-01-01

    In spite of much research effort, there is no universally applicable software reliability growth model which can be trusted to give accurate predictions of reliability in all circumstances. Further, it is not even possible to decide a priori which of the many models is most suitable in a particular context. In an attempt to resolve this problem, techniques were developed whereby, for each program, the accuracy of various models can be analyzed. A user is thus enabled to select that model which is giving the most accurate reliability predictions for the particular program under examination. One of these ways of analyzing predictive accuracy, called the u-plot, in fact allows a user to estimate the relationship between the predicted reliability and the true reliability. It is shown how this can be used to improve reliability predictions in a completely general way by a process of recalibration. Simulation results show that the technique gives improved reliability predictions in a large proportion of cases. However, a user does not need to trust the efficacy of recalibration, since the new reliability estimates produced by the technique are truly predictive and so their accuracy in a particular application can be judged using the earlier methods. The generality of this approach would therefore suggest that it be applied as a matter of course whenever a software reliability model is used.

  14. Reliability of Multi-Category Rating Scales

    ERIC Educational Resources Information Center

    Parker, Richard I.; Vannest, Kimberly J.; Davis, John L.

    2013-01-01

    The use of multi-category scales is increasing for the monitoring of IEP goals, classroom and school rules, and Behavior Improvement Plans (BIPs). Although they require greater inference than traditional data counting, little is known about the inter-rater reliability of these scales. This simulation study examined the performance of nine…

  15. Greater trochanter apophysitis in the adolescent athlete.

    PubMed

    Young, Simon W; Safran, Marc R

    2015-05-01

    Lower limb traction apophysitis is common in young athletes, occurring at sites such as the tibial tubercle (Osgood-Schlatter disease) and distal patella (Sinding-Larsen-Johansson disease). Around the hip, iliac apophysitis is well recognized, but no cases of greater trochanter apophysitis have previously been reported. We describe the case of a 15-year-old male basketball player with a 2-month history of the right hip pain and significant functional limitation. X-rays revealed widening of the greater trochanter apophysis with subchondral sclerosis, consistent with a diagnosis of traction apophysitis. The patient was treated with a period of relative rest and anti-inflammatory medication. He gradually returned to full athletic activity, including basketball, without recurrence of pain or limitation. We describe the first reported case of traction apophysitis of the greater trochanter. The unique muscular anatomy of this apophysis with balanced forces explains the rarity of this condition. If encountered, rest and activity modification is the recommended treatment.

  16. Graded Achievement, Tested Achievement, and Validity

    ERIC Educational Resources Information Center

    Brookhart, Susan M.

    2015-01-01

    Twenty-eight studies of grades, over a century, were reviewed using the argument-based approach to validity suggested by Kane as a theoretical framework. The review draws conclusions about the meaning of graded achievement, its relation to tested achievement, and changes in the construct of graded achievement over time. "Graded…

  17. Reliability based design optimization: Formulations and methodologies

    NASA Astrophysics Data System (ADS)

    Agarwal, Harish

    Modern products ranging from simple components to complex systems should be designed to be optimal and reliable. The challenge of modern engineering is to ensure that manufacturing costs are reduced and design cycle times are minimized while achieving requirements for performance and reliability. If the market for the product is competitive, improved quality and reliability can generate very strong competitive advantages. Simulation based design plays an important role in designing almost any kind of automotive, aerospace, and consumer products under these competitive conditions. Single discipline simulations used for analysis are being coupled together to create complex coupled simulation tools. This investigation focuses on the development of efficient and robust methodologies for reliability based design optimization in a simulation based design environment. Original contributions of this research are the development of a novel efficient and robust unilevel methodology for reliability based design optimization, the development of an innovative decoupled reliability based design optimization methodology, the application of homotopy techniques in unilevel reliability based design optimization methodology, and the development of a new framework for reliability based design optimization under epistemic uncertainty. The unilevel methodology for reliability based design optimization is shown to be mathematically equivalent to the traditional nested formulation. Numerical test problems show that the unilevel methodology can reduce computational cost by at least 50% as compared to the nested approach. The decoupled reliability based design optimization methodology is an approximate technique to obtain consistent reliable designs at lesser computational expense. Test problems show that the methodology is computationally efficient compared to the nested approach. A framework for performing reliability based design optimization under epistemic uncertainty is also developed

  18. A highly reliable LAN protocol

    NASA Astrophysics Data System (ADS)

    Weaver, A. C.

    1986-10-01

    As a research project for NASA's Langley Research Center, a variation on the military standard for avionics buses was developed to increase fault tolerance. The resulting protocol, called implicit token passing (ITP), replaces an explicit token with brief 'soundoff' messages from all nodes participating on the LAN. ITP features high throughput and bounded message delay, and achieves high reliability through tolerance of failed nodes and automatic resynchronization when failed nodes are revived. The protocol is ideally suited for a bus topology and fiber optic media.

  19. Reliability, Recursion, and Risk.

    ERIC Educational Resources Information Center

    Henriksen, Melvin, Ed.; Wagon, Stan, Ed.

    1991-01-01

    The discrete mathematics topics of trees and computational complexity are implemented in a simple reliability program which illustrates the process advantages of the PASCAL programing language. The discussion focuses on the impact that reliability research can provide in assessment of the risks found in complex technological ventures. (Author/JJK)

  20. Monte Carlo Reliability Analysis.

    DTIC Science & Technology

    1987-10-01

    to Stochastic Processes , Prentice-Hall, Englewood Cliffs, NJ, 1975. (5) R. E. Barlow and F. Proscham, Statistical TheorX of Reliability and Life...Lewis and Z. Tu, "Monte Carlo Reliability Modeling by Inhomogeneous ,Markov Processes, Reliab. Engr. 16, 277-296 (1986). (4) E. Cinlar, Introduction

  1. Chapter 9: Reliability

    SciTech Connect

    Algora, Carlos; Espinet-Gonzalez, Pilar; Vazquez, Manuel; Bosco, Nick; Miller, David; Kurtz, Sarah; Rubio, Francisca; McConnell,Robert

    2016-04-15

    This chapter describes the accumulated knowledge on CPV reliability with its fundamentals and qualification. It explains the reliability of solar cells, modules (including optics) and plants. The chapter discusses the statistical distributions, namely exponential, normal and Weibull. The reliability of solar cells includes: namely the issues in accelerated aging tests in CPV solar cells, types of failure and failures in real time operation. The chapter explores the accelerated life tests, namely qualitative life tests (mainly HALT) and quantitative accelerated life tests (QALT). It examines other well proven and experienced PV cells and/or semiconductor devices, which share similar semiconductor materials, manufacturing techniques or operating conditions, namely, III-V space solar cells and light emitting diodes (LEDs). It addresses each of the identified reliability issues and presents the current state of the art knowledge for their testing and evaluation. Finally, the chapter summarizes the CPV qualification and reliability standards.

  2. Greater Sage-Grouse National Research Strategy

    USGS Publications Warehouse

    Hanser, Steven E.; Manier, Daniel J.

    2013-01-01

    The condition of the sagebrush ecosystem has been declining in the Western United States, and greater sage-grouse (Centrocercus urophasianus), a sagebrush-obligate species, has experienced concurrent decreases in distribution and population numbers. This has prompted substantial research and management over the past two decades to improve the understanding of sage-grouse and its habitats and to address the observed decreases in distribution and population numbers. The amount of research and management has increased as the year 2015 approaches, which is when the U.S. Fish and Wildlife Service (FWS) is expected to make a final decision about whether or not to protect the species under the Endangered Species Act. In 2012, the Sage-Grouse Executive Oversight Committee (EOC) of the Western Association of Fish and Wildlife Agencies (WAFWA) requested that the U.S. Geological Survey (USGS) lead the development of a Greater Sage-Grouse National Research Strategy (hereafter Research Strategy). This request was motivated by a practical need to systematically connect existing research and conservation plans with persisting or emerging information needs. Managers and researchers also wanted to reduce redundancy and help focus limited funds on the highest priority research and management issues. The USGS undertook the development of this Research Strategy, which addresses information and science relating to the greater sage-grouse and its habitat across portions of 11 Western States. This Research Strategy provides an outline of important research topics to ensure that science information gaps are identified and documented in a comprehensive manner. Further, by identifying priority topics and critical information needed for planning, research, and resource management, it provides a structure to help coordinate members of an expansive research and management community in their efforts to conduct priority research.

  3. Primary torsion of the greater omentum.

    PubMed

    Gul, Y A; Jabbar, M F; Moissinac, K

    2001-01-01

    Primary or idiopathic greater omental torsion remains a rare cause of acute surgical abdomen in adults and children. The aetiology is as yet unknown and the treatment of choice, once diagnosis is established, is resection of the torted omentum. We report our experience with three such cases encountered over the last five years, two of which were diagnosed and subsequently managed laparoscopically. The performance of diagnostic laparoscopy for acute abdominal pain of an undetermined origin may lead to an increased detection of this condition and subsequent therapeutic intervention.

  4. Interspecific hybridization between greater kudu and nyala.

    PubMed

    Dalton, Desiré L; Tordiffe, Adrian; Luther, Ilse; Duran, Assumpta; van Wyk, Anna M; Brettschneider, Helene; Oosthuizen, Almero; Modiba, Catherine; Kotzé, Antoinette

    2014-06-01

    Hybridization of wildlife species, even in the absence of introgression, is of concern due to wasted reproductive effort and a reduction in productivity. In this study we detail an accidental mating between a female nyala (Tragelaphus angasii) and a male greater kudu (T. strepsiceros). The hybrid was phenotypically nyala and was identified as such based on mitochondrial DNA. Further genetic analysis based on nine microsatellite markers, chromosome number and chromosome morphology however, confirmed its status as an F1 hybrid. Results obtained from a reproductive potential assessment indicated that this animal does not have the potential to breed successfully and can be considered as sterile.

  5. Thiafentanil-dexmedetomidine-telazol anesthesia in greater rheas (Rhea americana).

    PubMed

    Ter Beest, Julia; McClean, Modesto; Cushing, Andrew; Bildfell, Robert

    2012-12-01

    Ratite anesthetic events are often dangerous because these birds use their powerful legs and clawed feet as a defense, and physical restraint can result in self-trauma or injury to handlers. Although various combinations of opioids, alpha-2 adrenergic agonists, and dissociative agents have been employed in ratites, few effective chemical immobilization protocols have been documented for rheas (Rhea spp.). An intramuscular, remote-delivered combination of thiafentanil (0.30 +/- 0.08 mg/kg), dexmedetomidine (7.31 +/- 2.72 microg/kg), and tiletamine-zolazepam (5.09 +/- 2.31 mg/kg) was utilized in eight adult (four male, four female) greater rheas (Rhea americana). Smooth inductions were observed. During clinical procedures, birds were intubated and maintained on isoflurane gas, and atipamezole was administered to antagonize the dexmedetomidine. At recovery, naltrexone was administered to antagonize the thiafentanil, and midazolam was administered to smooth crate recoveries until release. This low-volume, high-potency, reversible drug combination demonstrated safe inductions and smooth recoveries and proved to be a reliable anesthetic regimen for greater rheas.

  6. Mission reliability model programmers guide

    NASA Astrophysics Data System (ADS)

    Medina, Joseph M.; Simonson, Jonathan H.; Veatch, Michael H.

    1986-12-01

    The Mission Reliability Model (MIREM) has been developed to evaluate the reliability and sustained operating capability of advanced electronic circuits during the early stages of development. MIREM is applicable to integrated systems that achieve fault tolerance through dynamic fault detection, fault isolation, and reconfiguration. The model can also be valuable in evaluating designs that employ only dedicated or hard-wired redundancy. The most unique feature of MIREM is its ability to accurately reflect the impact of reconfigurable, competing functions on system reliability. The user defines the resources necessary to support a required function, e.g., Global Positioning System (GPS), and the model will compute the probability of losing that functional capability over a certain operating time. A critical failure occurs when there is not a sufficient number of working resources to support a specified function. As an analytic model, MIREM determines a value for Mean Time Between Critical Failure, Mission Completion Success Probability, and Failure Resiliency. The MIREM Programmers Guide addresses the model's program structure, function of routines, interdependence of subprograms and common blocks, and file usage. The information needed to port the model to other computer systems is also provided.

  7. Uncertainties in obtaining high reliability from stress-strength models

    NASA Technical Reports Server (NTRS)

    Neal, Donald M.; Matthews, William T.; Vangel, Mark G.

    1992-01-01

    There has been a recent interest in determining high statistical reliability in risk assessment of aircraft components. The potential consequences are identified of incorrectly assuming a particular statistical distribution for stress or strength data used in obtaining the high reliability values. The computation of the reliability is defined as the probability of the strength being greater than the stress over the range of stress values. This method is often referred to as the stress-strength model. A sensitivity analysis was performed involving a comparison of reliability results in order to evaluate the effects of assuming specific statistical distributions. Both known population distributions, and those that differed slightly from the known, were considered. Results showed substantial differences in reliability estimates even for almost nondetectable differences in the assumed distributions. These differences represent a potential problem in using the stress-strength model for high reliability computations, since in practice it is impossible to ever know the exact (population) distribution. An alternative reliability computation procedure is examined involving determination of a lower bound on the reliability values using extreme value distributions. This procedure reduces the possibility of obtaining nonconservative reliability estimates. Results indicated the method can provide conservative bounds when computing high reliability. An alternative reliability computation procedure is examined involving determination of a lower bound on the reliability values using extreme value distributions. This procedure reduces the possibility of obtaining nonconservative reliability estimates. Results indicated the method can provide conservative bounds when computing high reliability.

  8. Health and Greater Manchester in Historical Perspective

    PubMed Central

    Snow, Stephanie J.

    2015-01-01

    This article maps the history of health organisation across Greater Manchester (GM), primarily since the Second World War, to show how against a continuing backdrop of health inequalities, services have been driven (and constrained) by the needs and the politics of each period. Defining ‘success’ as benefits for patients the article identifies examples such as Salford’s mental health services (1950s and 1960s), public health in North Manchester (1970s and 1980s), the creation of centres for diabetes, sickle-cell and thalassaemia (1980s) and the formation of the Joint Health Unit in 2002. What this history shows is that over the period the common factors influencing the ‘success’ of health organisation across GM have been the championing of particular issues by multi-disciplinary groups working across health and social care and stability in structures and personnel. PMID:27499557

  9. Content validity and reliability of test of gross motor development in Chilean children

    PubMed Central

    Cano-Cappellacci, Marcelo; Leyton, Fernanda Aleitte; Carreño, Joshua Durán

    2016-01-01

    ABSTRACT OBJECTIVE To validate a Spanish version of the Test of Gross Motor Development (TGMD-2) for the Chilean population. METHODS Descriptive, transversal, non-experimental validity and reliability study. Four translators, three experts and 92 Chilean children, from five to 10 years, students from a primary school in Santiago, Chile, have participated. The Committee of Experts has carried out translation, back-translation and revision processes to determine the translinguistic equivalence and content validity of the test, using the content validity index in 2013. In addition, a pilot implementation was achieved to determine test reliability in Spanish, by using the intraclass correlation coefficient and Bland-Altman method. We evaluated whether the results presented significant differences by replacing the bat with a racket, using T-test. RESULTS We obtained a content validity index higher than 0.80 for language clarity and relevance of the TGMD-2 for children. There were significant differences in the object control subtest when comparing the results with bat and racket. The intraclass correlation coefficient for reliability inter-rater, intra-rater and test-retest reliability was greater than 0.80 in all cases. CONCLUSIONS The TGMD-2 has appropriate content validity to be applied in the Chilean population. The reliability of this test is within the appropriate parameters and its use could be recommended in this population after the establishment of normative data, setting a further precedent for the validation in other Latin American countries. PMID:26815160

  10. Reliability Analysis Model

    NASA Technical Reports Server (NTRS)

    1970-01-01

    RAM program determines probability of success for one or more given objectives in any complex system. Program includes failure mode and effects, criticality and reliability analyses, and some aspects of operations, safety, flight technology, systems design engineering, and configuration analyses.

  11. The rating reliability calculator

    PubMed Central

    Solomon, David J

    2004-01-01

    Background Rating scales form an important means of gathering evaluation data. Since important decisions are often based on these evaluations, determining the reliability of rating data can be critical. Most commonly used methods of estimating reliability require a complete set of ratings i.e. every subject being rated must be rated by each judge. Over fifty years ago Ebel described an algorithm for estimating the reliability of ratings based on incomplete data. While his article has been widely cited over the years, software based on the algorithm is not readily available. This paper describes an easy-to-use Web-based utility for estimating the reliability of ratings based on incomplete data using Ebel's algorithm. Methods The program is available public use on our server and the source code is freely available under GNU General Public License. The utility is written in PHP, a common open source imbedded scripting language. The rating data can be entered in a convenient format on the user's personal computer that the program will upload to the server for calculating the reliability and other statistics describing the ratings. Results When the program is run it displays the reliability, number of subject rated, harmonic mean number of judges rating each subject, the mean and standard deviation of the averaged ratings per subject. The program also displays the mean, standard deviation and number of ratings for each subject rated. Additionally the program will estimate the reliability of an average of a number of ratings for each subject via the Spearman-Brown prophecy formula. Conclusion This simple web-based program provides a convenient means of estimating the reliability of rating data without the need to conduct special studies in order to provide complete rating data. I would welcome other researchers revising and enhancing the program. PMID:15117416

  12. Metrology automation reliability

    NASA Astrophysics Data System (ADS)

    Chain, Elizabeth E.

    1996-09-01

    At Motorola's MOS-12 facility automated measurements on 200- mm diameter wafers proceed in a hands-off 'load-and-go' mode requiring only wafer loading, measurement recipe loading, and a 'run' command for processing. Upon completion of all sample measurements, the data is uploaded to the factory's data collection software system via a SECS II interface, eliminating the requirement of manual data entry. The scope of in-line measurement automation has been extended to the entire metrology scheme from job file generation to measurement and data collection. Data analysis and comparison to part specification limits is also carried out automatically. Successful integration of automated metrology into the factory measurement system requires that automated functions, such as autofocus and pattern recognition algorithms, display a high degree of reliability. In the 24- hour factory reliability data can be collected automatically on every part measured. This reliability data is then uploaded to the factory data collection software system at the same time as the measurement data. Analysis of the metrology reliability data permits improvements to be made as needed, and provides an accurate accounting of automation reliability. This reliability data has so far been collected for the CD-SEM (critical dimension scanning electron microscope) metrology tool, and examples are presented. This analysis method can be applied to such automated in-line measurements as CD, overlay, particle and film thickness measurements.

  13. Back to the Basics: In Defense of Achievement (and Achievement Tests) in College Admissions

    ERIC Educational Resources Information Center

    Geiser, Saul

    2009-01-01

    In this article, the author describes the growth and acceptance of achievement tests, such as the Scholastic Aptitude Test (SAT), over the past century, advocating that many SAT claims of equity, uniformity, technical reliability, and prediction, over traditional measures of academic achievement have been found to be illusory. Summarizing a series…

  14. Test Reliability by Ability Level of Examinees.

    ERIC Educational Resources Information Center

    Green, Kathy; Sax, Gilbert

    Achievement test reliability as a function of ability was determined for multiple sections of a large university French class (n=193). A 5-option multiple-choice examination was constructed, least attractive distractors were eliminated based on the instructor's judgment, and the resulting three forms of the examination (i.e. 3-, 4-, or 5-choice…

  15. Estimating the Reliability of a Crewed Spacecraft

    NASA Astrophysics Data System (ADS)

    Lutomski, M. G.; Garza, J.

    2012-01-01

    Now that the Space Shuttle Program has been retired, the Russian Soyuz Launcher and Soyuz Spacecraft are the only means for crew transportation to and from the International Space Station (ISS). Are the astronauts and cosmonauts safer on the Soyuz than the Space Shuttle system? How do you estimate the reliability of such a crewed spacecraft? The recent loss of the 44 Progress resupply flight to the ISS has put these questions front and center. The Soyuz launcher has been in operation for over 40 years. There have been only two Loss of Crew (LOC) incidents and two Loss of Mission (LOM) incidents involving crew missions. Given that the most recent crewed Soyuz launcher incident took place in 1983, how do we determine current reliability of such a system? How do all of the failures of unmanned Soyuz family launchers such as the 44P impact the reliability of the currently operational crewed launcher? Does the Soyuz exhibit characteristics that demonstrate reliability growth and how would that be reflected in future estimates of success? In addition NASA has begun development of the Orion or Multi-Purpose Crewed Vehicle as well as started an initiative to purchase Commercial Crew services from private firms. The reliability targets are currently several times higher than the last Shuttle reliability estimate. Can these targets be compared to the reliability of the Soyuz arguably the highest reliable crewed spacecraft and launcher in the world to determine whether they are realistic and achievable? To help answer these questions this paper will explore how to estimate the reliability of the Soyuz launcher/spacecraft system over its mission to give a benchmark for other human spaceflight vehicles and their missions. Specifically this paper will look at estimating the Loss of Mission (LOM) and Loss of Crew (LOC) probability for an ISS crewed Soyuz launcher/spacecraft mission using historical data, reliability growth, and Probabilistic Risk Assessment (PRA) techniques.

  16. Flight control electronics reliability/maintenance study

    NASA Technical Reports Server (NTRS)

    Dade, W. W.; Edwards, R. H.; Katt, G. T.; Mcclellan, K. L.; Shomber, H. A.

    1977-01-01

    Collection and analysis of data are reported that concern the reliability and maintenance experience of flight control system electronics currently in use on passenger carrying jet aircraft. Two airlines B-747 airplane fleets were analyzed to assess the component reliability, system functional reliability, and achieved availability of the CAT II configuration flight control system. Also assessed were the costs generated by this system in the categories of spare equipment, schedule irregularity, and line and shop maintenance. The results indicate that although there is a marked difference in the geographic location and route pattern between the airlines studied, there is a close similarity in the reliability and the maintenance costs associated with the flight control electronics.

  17. Water quality improvement plan for Greater Vancouver

    SciTech Connect

    Foellmi, S.N. . Environmental Div.); Neden, D.G. ); Dawson, R.N. )

    1993-10-01

    The Greater Vancouver Regional District commissioned an 18-month planning and predesign study to define the components in a comprehensive water and predesign study to define the components in a comprehensive water quality improvement plan for its 2,500-ML/d (660-mgd) system. The study included three primary tasks: (1) predesign of disinfection and corrosion control facilities, (2) a 12-month pilot testing program using parallel pilot plants at the Seymour and Capilano water supply reservoirs, and (3) planning for future filtration plants. The results of the study identified chlorine, ammonia, sulfur dioxide, soda ash, and carbon dioxide in a two-stage treatment approach as the recommended disinfection and corrosion control scheme for the low-pH, low-alkalinity water supplies. The pilot-plant studies confirmed that direct filtration using deep-bed monomedium filters operating at a loading rate of 22.5 m/h provided excellent treatment performance and productivity over a wide range of raw-water quality. Ozonation was studied extensively and found not to be beneficial in the overall treatment performance. The phased improvement plan for the disinfection, corrosion control, and filtration facilities has an estimated capital cost of about Can$459 million.

  18. Greater Green River Basin Production Improvement Project

    SciTech Connect

    DeJarnett, B.B.; Lim, F.H.; Calogero, D.

    1997-10-01

    The Greater Green River Basin (GGRB) of Wyoming has produced abundant oil and gas out of multiple reservoirs for over 60 years, and large quantities of gas remain untapped in tight gas sandstone reservoirs. Even though GGRB production has been established in formations from the Paleozoic to the Tertiary, recent activity has focused on several Cretaceous reservoirs. Two of these formations, the Ahnond and the Frontier Formations, have been classified as tight sands and are prolific producers in the GGRB. The formations typically naturally fractured and have been exploited using conventional well technology. In most cases, hydraulic fracture treatments must be performed when completing these wells to to increase gas production rates to economic levels. The objectives of the GGRB production improvement project were to apply the concept of horizontal and directional drilling to the Second Frontier Formation on the western flank of the Rock Springs Uplift and to compare production improvements by drilling, completing, and testing vertical, horizontal and directionally-drilled wellbores at a common site.

  19. Triatoma infestans in Greater Buenos Aires, Argentina.

    PubMed

    Gajate, P; Pietrokovsky, S; Abramo Orrego, L; Pérez, O; Monte, A; Belmonte, J; Wisnivesky-Colli, C

    2001-05-01

    The Health Administration Agencies of many municipalities in Greater Buenos Aires (GBA) receive frequent reports on triatomines in houses. The aim of this work was to identify and describe the dispersal foci of Triatoma infestans in an urban neighborhood of GBA, and contribute to the knowledge of the epidemiological situation in the region. In June 1998, potentially infested places were entomologically evaluated. T. infestans was only detected in a hen building for egg production, which housed approximately 6,000 birds. A total of 2,930 insects were collected. Density was about 9 triatomines/m(2). The proportions of fifth instar nymphs and adults were significantly higher than those of the other stages (p<0.001). The number of triatomines collected largely exceeded the highest domestic infestation found in one house from rural endemic areas of Argentina. Though triatomines were negative for Trypanosoma cruzi, they could acquire the parasite by coming in contact with infected people living in GBA. Besides, the numerous and widely distributed places housing hens and chickens, would favor the settlement of the vector. Together, both facts may constitute a risk of parasitic vectorial transmission. It is recommended to intensify systematic activities of vector search and case detection in GBA.

  20. Oral hormone replacement therapy: factors that influence the estradiol concentrations achieved in a multiracial study population.

    PubMed

    Gavaler, Judith S

    2002-02-01

    The assumption that estradiol (E2) concentrations are reliably increased to therapeutic levels in postmenopausal women receiving hormone replacement therapy (HRT) has not been explicitly tested. Nor have factors that may modulate the E2 levels achieved been evaluated. The author examined E2 concentrations in a multiracial study population of 309 postmenopausal women treated with oral HRT and observed that 51.1% had achieved estradiol levels of at least 45 pg/ml (achievers). The odds of being an achiever were significantly elevated among non-Caucasian women by a HRT dose greater than 0.625 mg, current moderate drinking, and increasing duration of HRT use. The odds were significantly decreased by having a high school education or less and increasing time since last HRT dose. White postmenopausal women had significantly reduced odds of being an achiever, and both a dose of less than 0.625 mg and a dose equal to 0.625 mg significantly reduced the odds of being an achiever. Increasing body mass index and menopause duration were both associated with lower odds. This report demonstrates not only that women treated with HRTdo not all achieve therapeutic levels of estradiol but also that factors can be identified that modulate the E2 concentration achieved in response to HRT administration.

  1. Statistical modelling of software reliability

    NASA Technical Reports Server (NTRS)

    Miller, Douglas R.

    1991-01-01

    During the six-month period from 1 April 1991 to 30 September 1991 the following research papers in statistical modeling of software reliability appeared: (1) A Nonparametric Software Reliability Growth Model; (2) On the Use and the Performance of Software Reliability Growth Models; (3) Research and Development Issues in Software Reliability Engineering; (4) Special Issues on Software; and (5) Software Reliability and Safety.

  2. Photovoltaic module reliability workshop

    SciTech Connect

    Mrig, L.

    1990-01-01

    The paper and presentations compiled in this volume form the Proceedings of the fourth in a series of Workshops sponsored by Solar Energy Research Institute (SERI/DOE) under the general theme of photovoltaic module reliability during the period 1986--1990. The reliability Photo Voltaic (PV) modules/systems is exceedingly important along with the initial cost and efficiency of modules if the PV technology has to make a major impact in the power generation market, and for it to compete with the conventional electricity producing technologies. The reliability of photovoltaic modules has progressed significantly in the last few years as evidenced by warranties available on commercial modules of as long as 12 years. However, there is still need for substantial research and testing required to improve module field reliability to levels of 30 years or more. Several small groups of researchers are involved in this research, development, and monitoring activity around the world. In the US, PV manufacturers, DOE laboratories, electric utilities and others are engaged in the photovoltaic reliability research and testing. This group of researchers and others interested in this field were brought together under SERI/DOE sponsorship to exchange the technical knowledge and field experience as related to current information in this important field. The papers presented here reflect this effort.

  3. Photovoltaic module reliability workshop

    NASA Astrophysics Data System (ADS)

    Mrig, L.

    The paper and presentations compiled in this volume form the Proceedings of the fourth in a series of Workshops sponsored by Solar Energy Research Institute (SERI/DOE) under the general theme of photovoltaic module reliability during the period 1986 to 1990. The reliability photovoltaic (PV) modules/systems is exceedingly important along with the initial cost and efficiency of modules if the PV technology has to make a major impact in the power generation market, and for it to compete with the conventional electricity producing technologies. The reliability of photovoltaic modules has progressed significantly in the last few years as evidenced by warrantees available on commercial modules of as long as 12 years. However, there is still need for substantial research and testing required to improve module field reliability to levels of 30 years or more. Several small groups of researchers are involved in this research, development, and monitoring activity around the world. In the U.S., PV manufacturers, DOE laboratories, electric utilities and others are engaged in the photovoltaic reliability research and testing. This group of researchers and others interested in this field were brought together under SERI/DOE sponsorship to exchange the technical knowledge and field experience as related to current information in this important field. The papers presented here reflect this effort.

  4. Orbiter Autoland reliability analysis

    NASA Technical Reports Server (NTRS)

    Welch, D. Phillip

    1993-01-01

    The Space Shuttle Orbiter is the only space reentry vehicle in which the crew is seated upright. This position presents some physiological effects requiring countermeasures to prevent a crewmember from becoming incapacitated. This also introduces a potential need for automated vehicle landing capability. Autoland is a primary procedure that was identified as a requirement for landing following and extended duration orbiter mission. This report documents the results of the reliability analysis performed on the hardware required for an automated landing. A reliability block diagram was used to evaluate system reliability. The analysis considers the manual and automated landing modes currently available on the Orbiter. (Autoland is presently a backup system only.) Results of this study indicate a +/- 36 percent probability of successfully extending a nominal mission to 30 days. Enough variations were evaluated to verify that the reliability could be altered with missions planning and procedures. If the crew is modeled as being fully capable after 30 days, the probability of a successful manual landing is comparable to that of Autoland because much of the hardware is used for both manual and automated landing modes. The analysis indicates that the reliability for the manual mode is limited by the hardware and depends greatly on crew capability. Crew capability for a successful landing after 30 days has not been determined yet.

  5. Proposed reliability cost model

    NASA Technical Reports Server (NTRS)

    Delionback, L. M.

    1973-01-01

    The research investigations which were involved in the study include: cost analysis/allocation, reliability and product assurance, forecasting methodology, systems analysis, and model-building. This is a classic example of an interdisciplinary problem, since the model-building requirements include the need for understanding and communication between technical disciplines on one hand, and the financial/accounting skill categories on the other. The systems approach is utilized within this context to establish a clearer and more objective relationship between reliability assurance and the subcategories (or subelements) that provide, or reenforce, the reliability assurance for a system. Subcategories are further subdivided as illustrated by a tree diagram. The reliability assurance elements can be seen to be potential alternative strategies, or approaches, depending on the specific goals/objectives of the trade studies. The scope was limited to the establishment of a proposed reliability cost-model format. The model format/approach is dependent upon the use of a series of subsystem-oriented CER's and sometimes possible CTR's, in devising a suitable cost-effective policy.

  6. 3D stress field simulation for Greater Munich, Germany

    NASA Astrophysics Data System (ADS)

    Ziegler, Moritz; Heidbach, Oliver; Reinecker, John; Przybycin, Anna Maria; Scheck-Wenderoth, Magdalena

    2016-04-01

    Geotechnical applications such as tunneling, storage of waste, wellbore planning, or reservoir engineering requires detailed 3D information on the rock properties and behavior of the continuum. One of the key parameters is the contemporary crustal in-situ stress state. However, generally the availability of stress data on reservoir scale is scarce or no data exists at all. Furthermore, stress data is often limited to the orientation of the maximum horizontal stress. Hence, geomechanical-numerical modelling provides an approximation of a continuous description of the 3D in-situ stress state. We present a model workflow that shows (1) how to calibrate a regional scale model of Greater Munich with stress orientations and magnitudes mainly from borehole data and (2) how to derive from the regional model boundary conditions for a local high-resolution model of a geothermal reservoir site. This approach using two models is an alternative to the required trade-off between resolution, computational cost and a sufficient number of calibration data which is otherwise inevitable for a single model. The incorporated 3D geological models contain the topography from a digital elevation model and 6 stratigraphic units with different elasto-plastic rock properties. The local model mimics the area of a planned reservoir and its resolution is significantly higher than in the regional model and down to 10 m near the planned borehole trajectories using 21×106 tetrahedron finite elements with linear approximation functions. The uncertainties of the calibrated regional model are large since no information on the magnitude of the maximum horizontal stress is available. Even in the entire Greater Munich area only two reliable leak-off tests that deliver the magnitude of the minimum horizontal stress could be used. These uncertainties are transferred also to the local model. Hence we also show how to quantify for the workflow in general the systematic uncertainties and discuss

  7. Reliability Centered Maintenance - Methodologies

    NASA Technical Reports Server (NTRS)

    Kammerer, Catherine C.

    2009-01-01

    Journal article about Reliability Centered Maintenance (RCM) methodologies used by United Space Alliance, LLC (USA) in support of the Space Shuttle Program at Kennedy Space Center. The USA Reliability Centered Maintenance program differs from traditional RCM programs because various methodologies are utilized to take advantage of their respective strengths for each application. Based on operational experience, USA has customized the traditional RCM methodology into a streamlined lean logic path and has implemented the use of statistical tools to drive the process. USA RCM has integrated many of the L6S tools into both RCM methodologies. The tools utilized in the Measure, Analyze, and Improve phases of a Lean Six Sigma project lend themselves to application in the RCM process. All USA RCM methodologies meet the requirements defined in SAE JA 1011, Evaluation Criteria for Reliability-Centered Maintenance (RCM) Processes. The proposed article explores these methodologies.

  8. Leader as achiever.

    PubMed

    Dienemann, Jacqueline

    2002-01-01

    This article examines one outcome of leadership: productive achievement. Without achievement one is judged to not truly be a leader. Thus, the ideal leader must be a visionary, a critical thinker, an expert, a communicator, a mentor, and an achiever of organizational goals. This article explores the organizational context that supports achievement, measures of quality nursing care, fiscal accountability, leadership development, rewards and punishments, and the educational content and teaching strategies to prepare graduates to be achievers.

  9. Gearbox Reliability Collaborative Update (Presentation)

    SciTech Connect

    Sheng, S.; Keller, J.; Glinsky, C.

    2013-10-01

    This presentation was given at the Sandia Reliability Workshop in August 2013 and provides information on current statistics, a status update, next steps, and other reliability research and development activities related to the Gearbox Reliability Collaborative.

  10. Reliability and Failure in NASA Missions: Blunders, Normal Accidents, High Reliability, Bad Luck

    NASA Technical Reports Server (NTRS)

    Jones, Harry W.

    2015-01-01

    NASA emphasizes crew safety and system reliability but several unfortunate failures have occurred. The Apollo 1 fire was mistakenly unanticipated. After that tragedy, the Apollo program gave much more attention to safety. The Challenger accident revealed that NASA had neglected safety and that management underestimated the high risk of shuttle. Probabilistic Risk Assessment was adopted to provide more accurate failure probabilities for shuttle and other missions. NASA's "faster, better, cheaper" initiative and government procurement reform led to deliberately dismantling traditional reliability engineering. The Columbia tragedy and Mars mission failures followed. Failures can be attributed to blunders, normal accidents, or bad luck. Achieving high reliability is difficult but possible.

  11. A comparative evaluation of the reliability improvement in line replaceable units warranted under the F-16 reliability improvement warranty

    NASA Astrophysics Data System (ADS)

    Lemke, S. J.

    1985-09-01

    This thesis examined the effects a reliability improvement warranty (RIW) had on the actual operational reliability of the warranted avionics equipment. To accomplish this, the most comprehensive DOD application of RIW to date, the F-16 RIW, was investigated. This study was designed to answer the question of whether or not a warranted weapons system was significantly more reliable than it would have been without the warranty. Specifically, the observed mean flight hours between failures (MFHBFs) and the observed reliability growths of the warranted F-16 equipment were compared to those of functionally similar non-warranted F-15 equipment. Also, the reliability growth of the F-16 warranted equipment was compared to that of other non-warranted F-16 equipment. The AMSAA Reliability Growth Model was used as a basis for the reliability growth analyses. Comparable life cycle time periods for each aircraft were studied, using AFM 66-1 D056 failure and flight time data. The results of the investigation indicated that, in general, the observed MFHBFs of the F-16 warranted equipment were statistically greater than the MFHBFs of the equivalent F-15 equipment. The same could not be concluded for the reliability growths of the F-16 and equivalent F-15 equipment. However, the reliability growth of the warranted F-16 equipment was found to be statistically greater than the reliability growth of the non-warranted F-16 equipment.

  12. Assuring Software Reliability

    DTIC Science & Technology

    2014-08-01

    resources.sei.cmu.edu/asset_files/WhitePaper/2009_019_001_29066.pdf [Boydston 2009] Boydston, A. & Lewis , W. Qualification and Reliability of...Woody, Carol . Survivability Analysis Framework (CMU/SEI-2010-TN-013). Software Engineering Institute, Carnegie Mellon University, 2010. http

  13. Parametric Mass Reliability Study

    NASA Technical Reports Server (NTRS)

    Holt, James P.

    2014-01-01

    The International Space Station (ISS) systems are designed based upon having redundant systems with replaceable orbital replacement units (ORUs). These ORUs are designed to be swapped out fairly quickly, but some are very large, and some are made up of many components. When an ORU fails, it is replaced on orbit with a spare; the failed unit is sometimes returned to Earth to be serviced and re-launched. Such a system is not feasible for a 500+ day long-duration mission beyond low Earth orbit. The components that make up these ORUs have mixed reliabilities. Components that make up the most mass-such as computer housings, pump casings, and the silicon board of PCBs-typically are the most reliable. Meanwhile components that tend to fail the earliest-such as seals or gaskets-typically have a small mass. To better understand the problem, my project is to create a parametric model that relates both the mass of ORUs to reliability, as well as the mass of ORU subcomponents to reliability.

  14. Sequential Reliability Tests.

    ERIC Educational Resources Information Center

    Eiting, Mindert H.

    1991-01-01

    A method is proposed for sequential evaluation of reliability of psychometric instruments. Sample size is unfixed; a test statistic is computed after each person is sampled and a decision is made in each stage of the sampling process. Results from a series of Monte-Carlo experiments establish the method's efficiency. (SLD)

  15. Designing reliability into accelerators

    SciTech Connect

    Hutton, A.

    1992-08-01

    For the next generation of high performance, high average luminosity colliders, the ``factories,`` reliability engineering must be introduced right at the inception of the project and maintained as a central theme throughout the project. There are several aspects which will be addressed separately: Concept; design; motivation; management techniques; and fault diagnosis.

  16. Designing reliability into accelerators

    SciTech Connect

    Hutton, A.

    1992-08-01

    For the next generation of high performance, high average luminosity colliders, the factories,'' reliability engineering must be introduced right at the inception of the project and maintained as a central theme throughout the project. There are several aspects which will be addressed separately: Concept; design; motivation; management techniques; and fault diagnosis.

  17. Reliable solar cookers

    SciTech Connect

    Magney, G.K.

    1992-12-31

    The author describes the activities of SERVE, a Christian relief and development agency, to introduce solar ovens to the Afghan refugees in Pakistan. It has provided 5,000 solar cookers since 1984. The experience has demonstrated the potential of the technology and the need for a durable and reliable product. Common complaints about the cookers are discussed and the ideal cooker is described.

  18. Software reliability report

    NASA Technical Reports Server (NTRS)

    Wilson, Larry

    1991-01-01

    There are many software reliability models which try to predict future performance of software based on data generated by the debugging process. Unfortunately, the models appear to be unable to account for the random nature of the data. If the same code is debugged multiple times and one of the models is used to make predictions, intolerable variance is observed in the resulting reliability predictions. It is believed that data replication can remove this variance in lab type situations and that it is less than scientific to talk about validating a software reliability model without considering replication. It is also believed that data replication may prove to be cost effective in the real world, thus the research centered on verification of the need for replication and on methodologies for generating replicated data in a cost effective manner. The context of the debugging graph was pursued by simulation and experimentation. Simulation was done for the Basic model and the Log-Poisson model. Reasonable values of the parameters were assigned and used to generate simulated data which is then processed by the models in order to determine limitations on their accuracy. These experiments exploit the existing software and program specimens which are in AIR-LAB to measure the performance of reliability models.

  19. Reliability Design Handbook

    DTIC Science & Technology

    1976-03-01

    prediction, failure modes and effects analysis ( FMEA ) and reliability growth techniques represent those prediction and design evaluation methods that...Assessment Production Operation Ö Maintenance MIL-HDBK- 217 Bayesian Techniques Probabilistic Design FMEA I R Growth " I...devices suffer thermal aging; oxidation and other chemical reactions are enhanced; viscosity reduction and evaporation of lubricants are problems

  20. Reliable vision-guided grasping

    NASA Technical Reports Server (NTRS)

    Nicewarner, Keith E.; Kelley, Robert B.

    1992-01-01

    Automated assembly of truss structures in space requires vision-guided servoing for grasping a strut when its position and orientation are uncertain. This paper presents a methodology for efficient and robust vision-guided robot grasping alignment. The vision-guided grasping problem is related to vision-guided 'docking' problems. It differs from other hand-in-eye visual servoing problems, such as tracking, in that the distance from the target is a relevant servo parameter. The methodology described in this paper is hierarchy of levels in which the vision/robot interface is decreasingly 'intelligent,' and increasingly fast. Speed is achieved primarily by information reduction. This reduction exploits the use of region-of-interest windows in the image plane and feature motion prediction. These reductions invariably require stringent assumptions about the image. Therefore, at a higher level, these assumptions are verified using slower, more reliable methods. This hierarchy provides for robust error recovery in that when a lower-level routine fails, the next-higher routine will be called and so on. A working system is described which visually aligns a robot to grasp a cylindrical strut. The system uses a single camera mounted on the end effector of a robot and requires only crude calibration parameters. The grasping procedure is fast and reliable, with a multi-level error recovery system.

  1. Throwing performance and test-retest reliability in Olympic female water polo players.

    PubMed

    Freeston, Jonathan; Rooney, Kieron; Smith, Stephen; OʼMeara, Damien

    2014-08-01

    Shooting performance is critical to successful water polo performance, requiring high levels of speed and accuracy. However, shooting speed and accuracy performance of elite female water polo players has not been described in detail nor has the reliability of accuracy measures been reported. Consequently, the aim of this study was to describe shooting performance in elite female water polo players and compare the test-retest reliability of the currently available accuracy measures. Ten Olympic female water polo players were tested on 3 occasions before Olympic competition for maximal throwing speed and accuracy (total error and hit percentage) toward various target locations, with and without a goalkeeper (GK) present. The current participants (all Olympic athletes) achieved higher speeds (16.8 m·s-1), higher hit percentages (45.3%) of a 20-cm sniper net target, and lower errors (20.7 cm) than any other female water polo players investigated previously. Performance was similar across the different target locations; however, both speed (15.2 vs. 14.8 m·s-1; p ≤ 0.05) and accuracy (50.2 vs. 37.7%; p ≤ 0.05) were reduced in the presence of a GK. Speed and total error was similar across the 3 testing sessions; however, hit percentage was statistically significantly higher in the final session (58.8% vs. 40.4 and 36.4%). Maximal throwing speed showed high levels of test-retest reliability (0.96). Total error (intraclass correlation [ICC] = 0.79) had slightly greater reliability than hit percentage (ICC = 0.73) overall. Hit percentage (ICC = 0.82) showed slightly greater reliability than total error (ICC = 0.72) without a GK present, whereas total error (ICC = 0.79) showed much greater reliability than hit percentage (ICC = 0.34) when a GK was present. This study benchmarks the high degree of throwing speed and accuracy required at the Olympic level in female water polo players. Although resource intensive, total error is a reliable measure of accuracy that allows

  2. Evaluation and management of greater trochanter pain syndrome.

    PubMed

    Mulligan, Edward P; Middleton, Emily F; Brunette, Meredith

    2015-08-01

    Greater trochanteric pain syndrome is an enigmatic but common cause of lateral hip symptoms in middle-aged active women. The most common manifestation of this syndrome is a degenerative tendinopathy of the hip abductors similar to the intrinsic changes seen with rotator cuff pathology in the shoulder. There are no definitive tests to isolate the underlying pathology and palpation is a non-specific means by which to differentiate the source of the pain generator. The physical examination must comprehensively evaluate for a cluster of potential impairments and contributing factors that will need to be addressed to effectively manage the likely functional limitations and activity challenges the syndrome presents to the patient. Compressive forces through increased tension in the iliotibial band should be avoided. Intervention strategies should include education regarding postural avoidance, activity modifications, improvement of lumbopelvic control, and a patient approach to resolving hip joint restrictions and restoring the tensile capabilities of the deep rotators and abductors of the hip. A number of reliable and validated hip-specific self-report outcome tools are available to baseline a patient's status and monitor their progress. Further investigations to identify the epidemiological risk factors, establish effective treatment strategies, and predict prognosis are warranted.

  3. Reliability Generalization (RG) Analysis: The Test Is Not Reliable

    ERIC Educational Resources Information Center

    Warne, Russell

    2008-01-01

    Literature shows that most researchers are unaware of some of the characteristics of reliability. This paper clarifies some misconceptions by describing the procedures, benefits, and limitations of reliability generalization while using it to illustrate the nature of score reliability. Reliability generalization (RG) is a meta-analytic method…

  4. Teacher Involvement To Evaluate Science Achievement.

    ERIC Educational Resources Information Center

    Ediger, Marlow

    Teacher-developed tests can be more valid and reliable than standardized tests or state-mandated tests in evaluating student achievement in science. Many teachers, however, are not acquainted with the standards to use in test writing. The National Research Council has released "Classroom Assessment and the National Education Standards," a…

  5. Three brief assessments of math achievement.

    PubMed

    Steiner, Eric T; Ashcraft, Mark H

    2012-12-01

    Because of wide disparities in college students' math knowledge-that is, their math achievement-studies of cognitive processing in math tasks also need to assess their individual level of math achievement. For many research settings, however, using existing math achievement tests is either too costly or too time consuming. To solve this dilemma, we present three brief tests of math achievement here, two drawn from the Wide Range Achievement Test and one composed of noncopyrighted items. All three correlated substantially with the full achievement test and with math anxiety, our original focus, and all show acceptable to excellent reliability. When lengthy testing is not feasible, one of these brief tests can be substituted.

  6. Multi-Disciplinary System Reliability Analysis

    NASA Technical Reports Server (NTRS)

    Mahadevan, Sankaran; Han, Song

    1997-01-01

    The objective of this study is to develop a new methodology for estimating the reliability of engineering systems that encompass multiple disciplines. The methodology is formulated in the context of the NESSUS probabilistic structural analysis code developed under the leadership of NASA Lewis Research Center. The NESSUS code has been successfully applied to the reliability estimation of a variety of structural engineering systems. This study examines whether the features of NESSUS could be used to investigate the reliability of systems in other disciplines such as heat transfer, fluid mechanics, electrical circuits etc., without considerable programming effort specific to each discipline. In this study, the mechanical equivalence between system behavior models in different disciplines are investigated to achieve this objective. A new methodology is presented for the analysis of heat transfer, fluid flow, and electrical circuit problems using the structural analysis routines within NESSUS, by utilizing the equivalence between the computational quantities in different disciplines. This technique is integrated with the fast probability integration and system reliability techniques within the NESSUS code, to successfully compute the system reliability of multi-disciplinary systems. Traditional as well as progressive failure analysis methods for system reliability estimation are demonstrated, through a numerical example of a heat exchanger system involving failure modes in structural, heat transfer and fluid flow disciplines.

  7. Comparing Science Achievement Constructs: Targeted and Achieved

    ERIC Educational Resources Information Center

    Ferrara, Steve; Duncan, Teresa

    2011-01-01

    This article illustrates how test specifications based solely on academic content standards, without attention to other cognitive skills and item response demands, can fall short of their targeted constructs. First, the authors inductively describe the science achievement construct represented by a statewide sixth-grade science proficiency test.…

  8. Estimating the impact on health of poor reliability of drinking water interventions in developing countries.

    PubMed

    Hunter, Paul R; Zmirou-Navier, Denis; Hartemann, Philippe

    2009-04-01

    Recent evidence suggests that many improved drinking water supplies suffer from poor reliability. This study investigates what impact poor reliability may have on achieving health improvement targets. A Quantitative Microbiological Risk Assessment was conducted of the impact of interruptions in water supplies that forced people to revert to drinking raw water. Data from the literature were used to construct models on three waterborne pathogens common in Africa: Rotavirus, Cryptosporidium and Enterotoxigenic E. coli. Risk of infection by the target pathogens is substantially greater on days that people revert to raw water consumption. Over the course of a few days raw water consumption, the annual health benefits attributed to consumption of water from an improved supply will be almost all lost. Furthermore, risk of illness on days drinking raw water will fall substantially on very young children who have the highest risk of death following infection. Agencies responsible for implementing improved drinking water provision will not make meaningful contributions to public health targets if those systems are subject to poor reliability. Funders of water quality interventions in developing countries should put more effort into auditing whether interventions are sustainable and whether the health benefits are being achieved.

  9. Which Achievement Gap?

    ERIC Educational Resources Information Center

    Anderson, Sharon; Medrich, Elliott; Fowler, Donna

    2007-01-01

    From the halls of Congress to the local elementary school, conversations on education reform have tossed around the term "achievement gap" as though people all know precisely what that means. As it's commonly used, "achievement gap" refers to the differences in scores on state or national achievement tests between various…

  10. Space Shuttle Propulsion System Reliability

    NASA Technical Reports Server (NTRS)

    Welzyn, Ken; VanHooser, Katherine; Moore, Dennis; Wood, David

    2011-01-01

    This session includes the following sessions: (1) External Tank (ET) System Reliability and Lessons, (2) Space Shuttle Main Engine (SSME), Reliability Validated by a Million Seconds of Testing, (3) Reusable Solid Rocket Motor (RSRM) Reliability via Process Control, and (4) Solid Rocket Booster (SRB) Reliability via Acceptance and Testing.

  11. Construction of Valid and Reliable Test for Assessment of Students

    ERIC Educational Resources Information Center

    Osadebe, P. U.

    2015-01-01

    The study was carried out to construct a valid and reliable test in Economics for secondary school students. Two research questions were drawn to guide the establishment of validity and reliability for the Economics Achievement Test (EAT). It is a multiple choice objective test of five options with 100 items. A sample of 1000 students was randomly…

  12. Human Reliability Program Workshop

    SciTech Connect

    Landers, John; Rogers, Erin; Gerke, Gretchen

    2014-05-18

    A Human Reliability Program (HRP) is designed to protect national security as well as worker and public safety by continuously evaluating the reliability of those who have access to sensitive materials, facilities, and programs. Some elements of a site HRP include systematic (1) supervisory reviews, (2) medical and psychological assessments, (3) management evaluations, (4) personnel security reviews, and (4) training of HRP staff and critical positions. Over the years of implementing an HRP, the Department of Energy (DOE) has faced various challenges and overcome obstacles. During this 4-day activity, participants will examine programs that mitigate threats to nuclear security and the insider threat to include HRP, Nuclear Security Culture (NSC) Enhancement, and Employee Assistance Programs. The focus will be to develop an understanding of the need for a systematic HRP and to discuss challenges and best practices associated with mitigating the insider threat.

  13. Reliable broadcast protocols

    NASA Technical Reports Server (NTRS)

    Joseph, T. A.; Birman, Kenneth P.

    1989-01-01

    A number of broadcast protocols that are reliable subject to a variety of ordering and delivery guarantees are considered. Developing applications that are distributed over a number of sites and/or must tolerate the failures of some of them becomes a considerably simpler task when such protocols are available for communication. Without such protocols the kinds of distributed applications that can reasonably be built will have a very limited scope. As the trend towards distribution and decentralization continues, it will not be surprising if reliable broadcast protocols have the same role in distributed operating systems of the future that message passing mechanisms have in the operating systems of today. On the other hand, the problems of engineering such a system remain large. For example, deciding which protocol is the most appropriate to use in a certain situation or how to balance the latency-communication-storage costs is not an easy question.

  14. Compact, Reliable EEPROM Controller

    NASA Technical Reports Server (NTRS)

    Katz, Richard; Kleyner, Igor

    2010-01-01

    A compact, reliable controller for an electrically erasable, programmable read-only memory (EEPROM) has been developed specifically for a space-flight application. The design may be adaptable to other applications in which there are requirements for reliability in general and, in particular, for prevention of inadvertent writing of data in EEPROM cells. Inadvertent writes pose risks of loss of reliability in the original space-flight application and could pose such risks in other applications. Prior EEPROM controllers are large and complex and do not provide all reasonable protections (in many cases, few or no protections) against inadvertent writes. In contrast, the present controller provides several layers of protection against inadvertent writes. The controller also incorporates a write-time monitor, enabling determination of trends in the performance of an EEPROM through all phases of testing. The controller has been designed as an integral subsystem of a system that includes not only the controller and the controlled EEPROM aboard a spacecraft but also computers in a ground control station, relatively simple onboard support circuitry, and an onboard communication subsystem that utilizes the MIL-STD-1553B protocol. (MIL-STD-1553B is a military standard that encompasses a method of communication and electrical-interface requirements for digital electronic subsystems connected to a data bus. MIL-STD- 1553B is commonly used in defense and space applications.) The intent was to both maximize reliability while minimizing the size and complexity of onboard circuitry. In operation, control of the EEPROM is effected via the ground computers, the MIL-STD-1553B communication subsystem, and the onboard support circuitry, all of which, in combination, provide the multiple layers of protection against inadvertent writes. There is no controller software, unlike in many prior EEPROM controllers; software can be a major contributor to unreliability, particularly in fault

  15. Designing reliability into accelerators

    NASA Astrophysics Data System (ADS)

    Hutton, A.

    1992-07-01

    Future accelerators will have to provide a high degree of reliability. Quality must be designed in right from the beginning and must remain a central theme throughout the project. The problem is similar to the problems facing US industry today, and examples of the successful application of quality engineering will be given. Different aspects of an accelerator project will be addressed: Concept, Design, Motivation, Management Techniques, and Fault Diagnosis. The importance of creating and maintaining a coherent team will be stressed.

  16. Reliability and testing

    NASA Technical Reports Server (NTRS)

    Auer, Werner

    1996-01-01

    Reliability and its interdependence with testing are important topics for development and manufacturing of successful products. This generally accepted fact is not only a technical statement, but must be also seen in the light of 'Human Factors.' While the background for this paper is the experience gained with electromechanical/electronic space products, including control and system considerations, it is believed that the content could be also of interest for other fields.

  17. Laser System Reliability

    DTIC Science & Technology

    1977-03-01

    NEALE CAPT. RANDALL D. GODFREY CAPT. JOHN E. ACTON HR. DAVE B. LEMMING (ASD) :,^ 19 . ••^w**** SECTION III RELIABILITY PREDICTION...Dete Exchange Program) failure rate date bank. In addition, some data have been obtained from Hughes. Rocketdyne , Garrett, and the AFWL’s APT Failure...Central Ave, Suite 306, Albuq, NM 87108 R/M Systems, Inc (Dr. K. Blemel), 10801 Lomas 81vd NE, Albuquerque, NM 87112 Rocketdyne 01 v, Rockwell

  18. Spacecraft transmitter reliability

    NASA Technical Reports Server (NTRS)

    1980-01-01

    A workshop on spacecraft transmitter reliability was held at the NASA Lewis Research Center on September 25 and 26, 1979, to discuss present knowledge and to plan future research areas. Since formal papers were not submitted, this synopsis was derived from audio tapes of the workshop. The following subjects were covered: users' experience with space transmitters; cathodes; power supplies and interfaces; and specifications and quality assurance. A panel discussion ended the workshop.

  19. Software reliability studies

    NASA Technical Reports Server (NTRS)

    Hoppa, Mary Ann; Wilson, Larry W.

    1994-01-01

    There are many software reliability models which try to predict future performance of software based on data generated by the debugging process. Our research has shown that by improving the quality of the data one can greatly improve the predictions. We are working on methodologies which control some of the randomness inherent in the standard data generation processes in order to improve the accuracy of predictions. Our contribution is twofold in that we describe an experimental methodology using a data structure called the debugging graph and apply this methodology to assess the robustness of existing models. The debugging graph is used to analyze the effects of various fault recovery orders on the predictive accuracy of several well-known software reliability algorithms. We found that, along a particular debugging path in the graph, the predictive performance of different models can vary greatly. Similarly, just because a model 'fits' a given path's data well does not guarantee that the model would perform well on a different path. Further we observed bug interactions and noted their potential effects on the predictive process. We saw that not only do different faults fail at different rates, but that those rates can be affected by the particular debugging stage at which the rates are evaluated. Based on our experiment, we conjecture that the accuracy of a reliability prediction is affected by the fault recovery order as well as by fault interaction.

  20. Illustrated structural application of universal first-order reliability method

    NASA Technical Reports Server (NTRS)

    Verderaime, V.

    1994-01-01

    The general application of the proposed first-order reliability method was achieved through the universal normalization of engineering probability distribution data. The method superimposes prevailing deterministic techniques and practices on the first-order reliability method to surmount deficiencies of the deterministic method and provide benefits of reliability techniques and predictions. A reliability design factor is derived from the reliability criterion to satisfy a specified reliability and is analogous to the deterministic safety factor. Its application is numerically illustrated on several practical structural design and verification cases with interesting results and insights. Two concepts of reliability selection criteria are suggested. Though the method was developed to support affordable structures for access to space, the method should also be applicable for most high-performance air and surface transportation systems.

  1. General Aviation Aircraft Reliability Study

    NASA Technical Reports Server (NTRS)

    Pettit, Duane; Turnbull, Andrew; Roelant, Henk A. (Technical Monitor)

    2001-01-01

    This reliability study was performed in order to provide the aviation community with an estimate of Complex General Aviation (GA) Aircraft System reliability. To successfully improve the safety and reliability for the next generation of GA aircraft, a study of current GA aircraft attributes was prudent. This was accomplished by benchmarking the reliability of operational Complex GA Aircraft Systems. Specifically, Complex GA Aircraft System reliability was estimated using data obtained from the logbooks of a random sample of the Complex GA Aircraft population.

  2. Photovoltaic-Reliability R&D Toward a Solar-Powered World (Presentation)

    SciTech Connect

    Kurtz, S.; Granata, J.

    2009-08-01

    Presentation about the importance of continued progress toward low-cost, high-reliability, and high-performance PV systems. High reliability is an essential element in achieving low-cost solar electricity.

  3. Neuroanatomical Correlates of the Income Achievement Gap

    PubMed Central

    Mackey, Allyson P.; Finn, Amy S.; Leonard, Julia A.; Jacoby Senghor, Drew S.; West, Martin R.; Gabrieli, Christopher F.O.; Gabrieli, John D. E.

    2015-01-01

    In the United States, the difference in academic achievement between higher- and lower-income students (i.e., the income achievement gap) is substantial and growing. Here, we investigated neuroanatomical correlates of this gap in adolescents (n = 58) in whom academic achievement was measured by statewide standardized testing. Cortical gray matter volume was significantly greater in students from higher-income backgrounds (n = 35) compared to students from lower-income backgrounds (n = 23), but cortical white matter volume and total cortical surface area did not differ between groups. Cortical thickness in all lobes of the brain was greater in students from higher-income than lower-income backgrounds. Thicker cortex, particularly in temporal and occipital lobes, was associated with better test performance. These results represent the first evidence that cortical thickness differs across broad swaths of the brain between higher- and lower-income students, and that cortical thickness is related to academic achievement test scores. PMID:25896418

  4. Ultra Reliable Closed Loop Life Support for Long Space Missions

    NASA Technical Reports Server (NTRS)

    Jones, Harry W.; Ewert, Michael K.

    2010-01-01

    Spacecraft human life support systems can achieve ultra reliability by providing sufficient spares to replace all failed components. The additional mass of spares for ultra reliability is approximately equal to the original system mass, provided that the original system reliability is not too low. Acceptable reliability can be achieved for the Space Shuttle and Space Station by preventive maintenance and by replacing failed units. However, on-demand maintenance and repair requires a logistics supply chain in place to provide the needed spares. In contrast, a Mars or other long space mission must take along all the needed spares, since resupply is not possible. Long missions must achieve ultra reliability, a very low failure rate per hour, since they will take years rather than weeks and cannot be cut short if a failure occurs. Also, distant missions have a much higher mass launch cost per kilogram than near-Earth missions. Achieving ultra reliable spacecraft life support systems with acceptable mass will require a well-planned and extensive development effort. Analysis must determine the reliability requirement and allocate it to subsystems and components. Ultra reliability requires reducing the intrinsic failure causes, providing spares to replace failed components and having "graceful" failure modes. Technologies, components, and materials must be selected and designed for high reliability. Long duration testing is needed to confirm very low failure rates. Systems design should segregate the failure causes in the smallest, most easily replaceable parts. The system must be designed, developed, integrated, and tested with system reliability in mind. Maintenance and reparability of failed units must not add to the probability of failure. The overall system must be tested sufficiently to identify any design errors. A program to develop ultra reliable space life support systems with acceptable mass should start soon since it must be a long term effort.

  5. Experts’ Opinions on the Reliability Gap and Some Practical Guidelines on Reliability Growth

    DTIC Science & Technology

    1988-09-01

    and found the ratio of the disparity to range 2 from 2.1:1 to 9.1:1 (38:231). Furthermore, Montemayor (54) studied the reliability gap between...Production, 17 October 1986. 54. Montemayor , A. J. "Achieved versus Predicted Mean-Time-Between-Failures (M.TBF)." The Boeing Company, D194-300341, March

  6. CR reliability testing

    NASA Astrophysics Data System (ADS)

    Honeyman-Buck, Janice C.; Rill, Lynn; Frost, Meryll M.; Staab, Edward V.

    1998-07-01

    The purpose of this work was to develop a method for systematically testing the reliability of a CR system under realistic daily loads in a non-clinical environment prior to its clinical adoption. Once digital imaging replaces film, it will be very difficult to revert back should the digital system become unreliable. Prior to the beginning of the test, a formal evaluation was performed to set the benchmarks for performance and functionality. A formal protocol was established that included all the 62 imaging plates in the inventory for each 24-hour period in the study. Imaging plates were exposed using different combinations of collimation, orientation, and SID. Anthropomorphic phantoms were used to acquire images of different sizes. Each combination was chosen randomly to simulate the differences that could occur in clinical practice. The tests were performed over a wide range of times with batches of plates processed to simulate the temporal constraints required by the nature of portable radiographs taken in the Intensive Care Unit (ICU). Current patient demographics were used for the test studies so automatic routing algorithms could be tested. During the test, only three minor reliability problems occurred, two of which were not directly related to the CR unit. One plate was discovered to cause a segmentation error that essentially reduced the image to only black and white with no gray levels. This plate was removed from the inventory to be replaced. Another problem was a PACS routing problem that occurred when the DICOM server with which the CR was communicating had a problem with disk space. The final problem was a network printing failure to the laser cameras. Although the units passed the reliability test, problems with interfacing to workstations were discovered. The two issues that were identified were the interpretation of what constitutes a study for CR and the construction of the look-up table for a proper gray scale display.

  7. Ultimately Reliable Pyrotechnic Systems

    NASA Technical Reports Server (NTRS)

    Scott, John H.; Hinkel, Todd

    2015-01-01

    This paper presents the methods by which NASA has designed, built, tested, and certified pyrotechnic devices for high reliability operation in extreme environments and illustrates the potential applications in the oil and gas industry. NASA's extremely successful application of pyrotechnics is built upon documented procedures and test methods that have been maintained and developed since the Apollo Program. Standards are managed and rigorously enforced for performance margins, redundancy, lot sampling, and personnel safety. The pyrotechnics utilized in spacecraft include such devices as small initiators and detonators with the power of a shotgun shell, detonating cord systems for explosive energy transfer across many feet, precision linear shaped charges for breaking structural membranes, and booster charges to actuate valves and pistons. NASA's pyrotechnics program is one of the more successful in the history of Human Spaceflight. No pyrotechnic device developed in accordance with NASA's Human Spaceflight standards has ever failed in flight use. NASA's pyrotechnic initiators work reliably in temperatures as low as -420 F. Each of the 135 Space Shuttle flights fired 102 of these initiators, some setting off multiple pyrotechnic devices, with never a failure. The recent landing on Mars of the Opportunity rover fired 174 of NASA's pyrotechnic initiators to complete the famous '7 minutes of terror.' Even after traveling through extreme radiation and thermal environments on the way to Mars, every one of them worked. These initiators have fired on the surface of Titan. NASA's design controls, procedures, and processes produce the most reliable pyrotechnics in the world. Application of pyrotechnics designed and procured in this manner could enable the energy industry's emergency equipment, such as shutoff valves and deep-sea blowout preventers, to be left in place for years in extreme environments and still be relied upon to function when needed, thus greatly enhancing

  8. Reliability Growth Prediction

    DTIC Science & Technology

    1986-09-01

    the Duane model because: *e ’he reliability gSod’ data analyzed were reflective of a single Lesr- for • each equipment as opposed to a series of zest ...fabrication) and costs wbich are a function of test length (e.g., chamber operations). A life -cycle cost model, Ref. 14 for example, can be exercised tc...J. Gibson and K. K. Mcain APPROVED FOR FUBLIC RE1EAS NI ODSrRUTIG1,N UY-LUlHfF :-:-4 ROME AIR DEVELOPMENT CENTER Air Force Systems Command Griffiss

  9. Blade reliability collaborative :

    SciTech Connect

    Ashwill, Thomas D.; Ogilvie, Alistair B.; Paquette, Joshua A.

    2013-04-01

    The Blade Reliability Collaborative (BRC) was started by the Wind Energy Technologies Department of Sandia National Laboratories and DOE in 2010 with the goal of gaining insight into planned and unplanned O&M issues associated with wind turbine blades. A significant part of BRC is the Blade Defect, Damage and Repair Survey task, which will gather data from blade manufacturers, service companies, operators and prior studies to determine details about the largest sources of blade unreliability. This report summarizes the initial findings from this work.

  10. Ferrite logic reliability study

    NASA Technical Reports Server (NTRS)

    Baer, J. A.; Clark, C. B.

    1973-01-01

    Development and use of digital circuits called all-magnetic logic are reported. In these circuits the magnetic elements and their windings comprise the active circuit devices in the logic portion of a system. The ferrite logic device belongs to the all-magnetic class of logic circuits. The FLO device is novel in that it makes use of a dual or bimaterial ferrite composition in one physical ceramic body. This bimaterial feature, coupled with its potential for relatively high speed operation, makes it attractive for high reliability applications. (Maximum speed of operation approximately 50 kHz.)

  11. MEMS reliability in shock environments

    SciTech Connect

    TANNER,DANELLE M.; WALRAVEN,JEREMY A.; HELGESEN,KAREN SUE; IRWIN,LLOYD W.; BROWN,FREDERICK A.; SMITH,NORMAN F.; MASTERS,NATHAN

    2000-02-09

    In order to determine the susceptibility of the MEMS (MicroElectroMechanical Systems) devices to shock, tests were performed using haversine shock pulses with widths of 1 to 0.2 ms in the range from 500g to 40,000g. The authors chose a surface-micromachined microengine because it has all the components needed for evaluation: springs that flex, gears that are anchored, and clamps and spring stops to maintain alignment. The microengines, which were unpowered for the tests, performed quite well at most shock levels with a majority functioning after the impact. Debris from the die edges moved at levels greater than 4,000g causing shorts in the actuators and posing reliability concerns. The coupling agent used to prevent stiction in the MEMS release weakened the die-attach bond, which produced failures at 10,000g and above. At 20,000g the authors began to observe structural damage in some of the thin flexures and 2.5-micron diameter pin joints. The authors observed electrical failures caused by the movement of debris. Additionally, they observed a new failure mode where stationary comb fingers contact the ground plane resulting in electrical shorts. These new failure were observed in the control group indicating that they were not shock related.

  12. Testing of reliability - Analysis tools

    NASA Technical Reports Server (NTRS)

    Hayhurst, Kelly J.

    1989-01-01

    An outline is presented of issues raised in verifying the accuracy of reliability analysis tools. State-of-the-art reliability analysis tools implement various decomposition, aggregation, and estimation techniques to compute the reliability of a diversity of complex fault-tolerant computer systems. However, no formal methodology has been formulated for validating the reliability estimates produced by these tools. The author presents three states of testing that can be performed on most reliability analysis tools to effectively increase confidence in a tool. These testing stages were applied to the SURE (semi-Markov Unreliability Range Evaluator) reliability analysis tool, and the results of the testing are discussed.

  13. Schoolbook Texts: Behavioral Achievement Priming in Math and Language.

    PubMed

    Engeser, Stefan; Baumann, Nicola; Baum, Ingrid

    2016-01-01

    Prior research found reliable and considerably strong effects of semantic achievement primes on subsequent performance. In order to simulate a more natural priming condition to better understand the practical relevance of semantic achievement priming effects, running texts of schoolbook excerpts with and without achievement primes were used as priming stimuli. Additionally, we manipulated the achievement context; some subjects received no feedback about their achievement and others received feedback according to a social or individual reference norm. As expected, we found a reliable (albeit small) positive behavioral priming effect of semantic achievement primes on achievement in math (Experiment 1) and language tasks (Experiment 2). Feedback moderated the behavioral priming effect less consistently than we expected. The implication that achievement primes in schoolbooks can foster performance is discussed along with general theoretical implications.

  14. Schoolbook Texts: Behavioral Achievement Priming in Math and Language

    PubMed Central

    Engeser, Stefan; Baumann, Nicola; Baum, Ingrid

    2016-01-01

    Prior research found reliable and considerably strong effects of semantic achievement primes on subsequent performance. In order to simulate a more natural priming condition to better understand the practical relevance of semantic achievement priming effects, running texts of schoolbook excerpts with and without achievement primes were used as priming stimuli. Additionally, we manipulated the achievement context; some subjects received no feedback about their achievement and others received feedback according to a social or individual reference norm. As expected, we found a reliable (albeit small) positive behavioral priming effect of semantic achievement primes on achievement in math (Experiment 1) and language tasks (Experiment 2). Feedback moderated the behavioral priming effect less consistently than we expected. The implication that achievement primes in schoolbooks can foster performance is discussed along with general theoretical implications. PMID:26938446

  15. Systems reliability analysis for the national ignition facility

    SciTech Connect

    Majumdar, K.C.; Annese, C.E.; MacIntyre, A.T.; Sicherman, A.

    1996-06-12

    A Reliability, Availability and Maintainability (RAM) analysis was initiated for the National Ignition Facility (NIF). The NIF is an inertial confinement fusion research facility designed to achieve controlled thermonuclear reaction; the preferred site for the NIF is the Lawrence Livermore National Laboratory (LLNL). The NIF RAM analysis has three purposes: (1) to allocate top level reliability and availability goals for the systems, (2) to develop an operability model for optimum maintainability, and (3) to determine the achievability of the allocated goals of the RAM parameters for the NIF systems and the facility operation as a whole. An allocation model assigns the reliability and availability goals for front line and support systems by a top-down approach; reliability analysis uses a bottom-up approach to determine the system reliability and availability from component level to system level.

  16. Load Control System Reliability

    SciTech Connect

    Trudnowski, Daniel

    2015-04-03

    This report summarizes the results of the Load Control System Reliability project (DOE Award DE-FC26-06NT42750). The original grant was awarded to Montana Tech April 2006. Follow-on DOE awards and expansions to the project scope occurred August 2007, January 2009, April 2011, and April 2013. In addition to the DOE monies, the project also consisted of matching funds from the states of Montana and Wyoming. Project participants included Montana Tech; the University of Wyoming; Montana State University; NorthWestern Energy, Inc., and MSE. Research focused on two areas: real-time power-system load control methodologies; and, power-system measurement-based stability-assessment operation and control tools. The majority of effort was focused on area 2. Results from the research includes: development of fundamental power-system dynamic concepts, control schemes, and signal-processing algorithms; many papers (including two prize papers) in leading journals and conferences and leadership of IEEE activities; one patent; participation in major actual-system testing in the western North American power system; prototype power-system operation and control software installed and tested at three major North American control centers; and, the incubation of a new commercial-grade operation and control software tool. Work under this grant certainly supported the DOE-OE goals in the area of “Real Time Grid Reliability Management.”

  17. Integrated circuit reliability testing

    NASA Technical Reports Server (NTRS)

    Buehler, Martin G. (Inventor); Sayah, Hoshyar R. (Inventor)

    1990-01-01

    A technique is described for use in determining the reliability of microscopic conductors deposited on an uneven surface of an integrated circuit device. A wafer containing integrated circuit chips is formed with a test area having regions of different heights. At the time the conductors are formed on the chip areas of the wafer, an elongated serpentine assay conductor is deposited on the test area so the assay conductor extends over multiple steps between regions of different heights. Also, a first test conductor is deposited in the test area upon a uniform region of first height, and a second test conductor is deposited in the test area upon a uniform region of second height. The occurrence of high resistances at the steps between regions of different height is indicated by deriving the measured length of the serpentine conductor using the resistance measured between the ends of the serpentine conductor, and comparing that to the design length of the serpentine conductor. The percentage by which the measured length exceeds the design length, at which the integrated circuit will be discarded, depends on the required reliability of the integrated circuit.

  18. Integrated circuit reliability testing

    NASA Technical Reports Server (NTRS)

    Buehler, Martin G. (Inventor); Sayah, Hoshyar R. (Inventor)

    1988-01-01

    A technique is described for use in determining the reliability of microscopic conductors deposited on an uneven surface of an integrated circuit device. A wafer containing integrated circuit chips is formed with a test area having regions of different heights. At the time the conductors are formed on the chip areas of the wafer, an elongated serpentine assay conductor is deposited on the test area so the assay conductor extends over multiple steps between regions of different heights. Also, a first test conductor is deposited in the test area upon a uniform region of first height, and a second test conductor is deposited in the test area upon a uniform region of second height. The occurrence of high resistances at the steps between regions of different height is indicated by deriving the measured length of the serpentine conductor using the resistance measured between the ends of the serpentine conductor, and comparing that to the design length of the serpentine conductor. The percentage by which the measured length exceeds the design length, at which the integrated circuit will be discarded, depends on the required reliability of the integrated circuit.

  19. The Reliability of Neurons

    PubMed Central

    Bullock, Theodore Holmes

    1970-01-01

    The prevalent probabilistic view is virtually untestable; it remains a plausible belief. The cases usually cited can not be taken as evidence for it. Several grounds for this conclusion are developed. Three issues are distinguished in an attempt to clarify a murky debate: (a) the utility of probabilistic methods in data reduction, (b) the value of models that assume indeterminacy, and (c) the validity of the inference that the nervous system is largely indeterministic at the neuronal level. No exception is taken to the first two; the second is a private heuristic question. The third is the issue to which the assertion in the first two sentences is addressed. Of the two kinds of uncertainty, statistical mechanical (= practical unpredictability) as in a gas, and Heisenbergian indeterminancy, the first certainly exists, the second is moot at the neuronal level. It would contribute to discussion to recognize that neurons perform with a degree of reliability. Although unreliability is difficult to establish, to say nothing of measure, evidence that some neurons have a high degree of reliability, in both connections and activity is increasing greatly. An example is given from sternarchine electric fish. PMID:5462670

  20. Reliable Entanglement Verification

    NASA Astrophysics Data System (ADS)

    Arrazola, Juan; Gittsovich, Oleg; Donohue, John; Lavoie, Jonathan; Resch, Kevin; Lütkenhaus, Norbert

    2013-05-01

    Entanglement plays a central role in quantum protocols. It is therefore important to be able to verify the presence of entanglement in physical systems from experimental data. In the evaluation of these data, the proper treatment of statistical effects requires special attention, as one can never claim to have verified the presence of entanglement with certainty. Recently increased attention has been paid to the development of proper frameworks to pose and to answer these type of questions. In this work, we apply recent results by Christandl and Renner on reliable quantum state tomography to construct a reliable entanglement verification procedure based on the concept of confidence regions. The statements made do not require the specification of a prior distribution nor the assumption of an independent and identically distributed (i.i.d.) source of states. Moreover, we develop efficient numerical tools that are necessary to employ this approach in practice, rendering the procedure ready to be employed in current experiments. We demonstrate this fact by analyzing the data of an experiment where photonic entangled two-photon states were generated and whose entanglement is verified with the use of an accessible nonlinear witness.

  1. 'No delays achiever'.

    PubMed

    2007-05-01

    The latest version of the NHS Institute for Innovation and Improvement's 'no delays achiever', a web based tool created to help NHS organisations achieve the 18-week target for GP referrals to first treatment, is available at www.nodelaysachiever.nhs.uk.

  2. Vicarious Achievement Orientation.

    ERIC Educational Resources Information Center

    Leavitt, Harold J.; And Others

    This study tests hypotheses about achievement orientation, particularly vicarious achievement. Undergraduate students (N=437) completed multiple-choice questionnaires, indicating likely responses of one person to the success of another. The sex of succeeder and observer, closeness of relationship, and setting (medical school or graduate school of…

  3. Heritability of Creative Achievement

    ERIC Educational Resources Information Center

    Piffer, Davide; Hur, Yoon-Mi

    2014-01-01

    Although creative achievement is a subject of much attention to lay people, the origin of individual differences in creative accomplishments remain poorly understood. This study examined genetic and environmental influences on creative achievement in an adult sample of 338 twins (mean age = 26.3 years; SD = 6.6 years). Twins completed the Creative…

  4. Confronting the Achievement Gap

    ERIC Educational Resources Information Center

    Gardner, David

    2007-01-01

    This article talks about the large achievement gap between children of color and their white peers. The reasons for the achievement gap are varied. First, many urban minorities come from a background of poverty. One of the detrimental effects of growing up in poverty is receiving inadequate nourishment at a time when bodies and brains are rapidly…

  5. Achievement-Based Resourcing.

    ERIC Educational Resources Information Center

    Fletcher, Mike; And Others

    1992-01-01

    This collection of seven articles examines achievement-based resourcing (ABR), the concept that the funding of educational institutions should be linked to their success in promoting student achievement, with a focus on the application of ABR to postsecondary education in the United Kingdom. The articles include: (1) "Introduction" (Mick…

  6. States Address Achievement Gaps.

    ERIC Educational Resources Information Center

    Christie, Kathy

    2002-01-01

    Summarizes 2 state initiatives to address the achievement gap: North Carolina's report by the Advisory Commission on Raising Achievement and Closing Gaps, containing an 11-point strategy, and Kentucky's legislation putting in place 10 specific processes. The North Carolina report is available at www.dpi.state.nc.us.closingthegap; Kentucky's…

  7. Predicting educational achievement from DNA

    PubMed Central

    Selzam, S; Krapohl, E; von Stumm, S; O'Reilly, P F; Rimfeld, K; Kovas, Y; Dale, P S; Lee, J J; Plomin, R

    2017-01-01

    A genome-wide polygenic score (GPS), derived from a 2013 genome-wide association study (N=127,000), explained 2% of the variance in total years of education (EduYears). In a follow-up study (N=329,000), a new EduYears GPS explains up to 4%. Here, we tested the association between this latest EduYears GPS and educational achievement scores at ages 7, 12 and 16 in an independent sample of 5825 UK individuals. We found that EduYears GPS explained greater amounts of variance in educational achievement over time, up to 9% at age 16, accounting for 15% of the heritable variance. This is the strongest GPS prediction to date for quantitative behavioral traits. Individuals in the highest and lowest GPS septiles differed by a whole school grade at age 16. Furthermore, EduYears GPS was associated with general cognitive ability (~3.5%) and family socioeconomic status (~7%). There was no evidence of an interaction between EduYears GPS and family socioeconomic status on educational achievement or on general cognitive ability. These results are a harbinger of future widespread use of GPS to predict genetic risk and resilience in the social and behavioral sciences. PMID:27431296

  8. Creativity: The Hub of Real Achievement

    ERIC Educational Resources Information Center

    Forster, Jill

    2012-01-01

    The aim of this article is to encourage a greater emphasis on creativity across and between varied fields of endeavour. It has been written to underline the interdisciplinary significance of creativity and the role of creativity in truly enhancing achievement. There is a reinvigorated awareness of the need for "big thinking", a global…

  9. Achievability for telerobotic systems

    NASA Astrophysics Data System (ADS)

    Kress, Reid L.; Draper, John V.; Hamel, William R.

    2001-02-01

    Methods are needed to improve the capabilities of autonomous robots to perform tasks that are difficult for contemporary robots, and to identify those tasks that robots cannot perform. Additionally, in the realm of remote handling, methods are needed to assess which tasks and/or subtasks are candidates for automation. We are developing a new approach to understanding the capability of autonomous robotic systems. This approach uses formalized methods for determining the achievability of tasks for robots, that is, the likelihood that an autonomous robot or telerobot can successfully complete a particular task. Any autonomous system may be represented in achievability space by the volume describing that system's capabilities within the 3-axis space delineated by perception, cognition, and action. This volume may be thought of as a probability density with achievability decreasing as the distance from the centroid of the volume increases. Similarly, any task may be represented within achievability space. However, as tasks have more finite requirements for perception, cognition, and action, each may be represented as a point (or, more accurately, as a small sphere) within achievability space. Analysis of achievability can serve to identify, a priori, the survivability of robotic systems and the likelihood of mission success; it can be used to plan a mission or portions of a mission; it can be used to modify a mission plan to accommodate unpredicted occurrences; it can also serve to identify needs for modifications to robotic systems or tasks to improve achievability. .

  10. Monoamine Oxidase A (MAOA) Genotype Predicts Greater Aggression Through Impulsive Reactivity to Negative Affect

    PubMed Central

    Chester, David S.; DeWall, C. Nathan; Derefinko, Karen J.; Estus, Steven; Peters, Jessica R.; Lynam, Donald R.; Jiang, Yang

    2015-01-01

    Low functioning MAOA genotypes have been reliably linked to increased reactive aggression, yet the psychological mechanisms of this effect remain largely unknown. The low functioning MAOA genotype’s established link to diminished inhibition and greater reactivity to conditions of negative affect suggest that negative urgency, the tendency to act impulsively in the context of negative affect, may fill this mediating role. Such MAOA carriers may have higher negative urgency, which may in turn predict greater aggressive responses to provocation. To test these hypotheses, 277 female and male participants were genotyped for an MAOA SNP yet to be linked to aggression (rs1465108), and then reported their negative urgency and past aggressive behavior. We replicated the effect of the low functioning MAOA genotype on heightened aggression, which was mediated by greater negative urgency. These results suggest that disrupted serotonergic systems predispose individuals towards aggressive behavior by increasing impulsive reactivity to negative affect. PMID:25637908

  11. Monoamine oxidase A (MAOA) genotype predicts greater aggression through impulsive reactivity to negative affect.

    PubMed

    Chester, David S; DeWall, C Nathan; Derefinko, Karen J; Estus, Steven; Peters, Jessica R; Lynam, Donald R; Jiang, Yang

    2015-04-15

    Low functioning MAOA genotypes have been reliably linked to increased reactive aggression, yet the psychological mechanisms of this effect remain largely unknown. The low functioning MAOA genotype's established link to diminished inhibition and greater reactivity to conditions of negative affect suggest that negative urgency, the tendency to act impulsively in the context of negative affect, may fill this mediating role. Such MAOA carriers may have higher negative urgency, which may in turn predict greater aggressive responses to provocation. To test these hypotheses, 277 female and male participants were genotyped for an MAOA SNP yet to be linked to aggression (rs1465108), and then reported their negative urgency and past aggressive behavior. We replicated the effect of the low functioning MAOA genotype on heightened aggression, which was mediated by greater negative urgency. These results suggest that disrupted serotonergic systems predispose individuals towards aggressive behavior by increasing impulsive reactivity to negative affect.

  12. Testing for PV Reliability (Presentation)

    SciTech Connect

    Kurtz, S.; Bansal, S.

    2014-09-01

    The DOE SUNSHOT workshop is seeking input from the community about PV reliability and how the DOE might address gaps in understanding. This presentation describes the types of testing that are needed for PV reliability and introduces a discussion to identify gaps in our understanding of PV reliability testing.

  13. Making Reliability Arguments in Classrooms

    ERIC Educational Resources Information Center

    Parkes, Jay; Giron, Tilia

    2006-01-01

    Reliability methodology needs to evolve as validity has done into an argument supported by theory and empirical evidence. Nowhere is the inadequacy of current methods more visible than in classroom assessment. Reliability arguments would also permit additional methodologies for evidencing reliability in classrooms. It would liberalize methodology…

  14. Discrete Reliability Projection

    DTIC Science & Technology

    2014-12-01

    Defense, Handbook MIL - HDBK -189C, 2011 Hall, J. B., Methodology for Evaluating Reliability Growth Programs of Discrete Systems, Ph.D. thesis, University...pk,i ] · [ 1− (1− θ̆k) · ( N k · T )]k−m , (2.13) 5 2 Hall’s Model where m is the number of observed failure modes and d∗i estimates di (either based...Mode Failures FEF Ni d ∗ i 1 1 0.95 2 1 0.70 3 1 0.90 4 1 0.90 5 4 0.95 6 2 0.70 7 1 0.80 Using equations 2.1 and 2.2 we can calculate the failure

  15. Warsaw Pact: The Question of Cohesion. Phase II, Volume 1. The Greater Socialist Army: Integration and Reliability,

    DTIC Science & Technology

    1984-02-01

    management , justifiably described as an "alliance of a new type," denies national control over national armed forces to Bulgaria, Czechoslovakia, East...i on o! i **I al I I;t a rmed for ces n c oal IIt i on wa rfa r- of a ’’new t vpo . VI I. T h management of thle problem of pol It icalI relI abi I I...tv i n the Wars;aw Pact is, both an extension of domestic policies for managing the ethnic factor and a continuation of domestic HISTORICAL

  16. Influence of Mothers' Education on Children's Maths Achievement in Kenya

    ERIC Educational Resources Information Center

    Abuya, Benta A.; Oketch, Moses; Mutisya, Maurice; Ngware, Moses; Ciera, James

    2013-01-01

    Research shows that fathers' level of education predicts achievement of both boys and girls, with significantly greater effect for boys. Similarly, mothers' level of education predicts the achievement of girls but not boys. This study tests the mother-child education achievement hypothesis, by examining the effect of mothers' education on the…

  17. Culture and Achievement Motivation

    ERIC Educational Resources Information Center

    Maehr, Martin L.

    1974-01-01

    A framework is suggested for the cross-cultural study of motivation that stresses the importance of contextual conditions in eliciting achievement motivation and emphasizes cultural relativity in the definition of the concept. (EH)

  18. Achieving Salary Equity

    ERIC Educational Resources Information Center

    Nevill, Dorothy D.

    1975-01-01

    Three techniques are outlined for use by higher education institutions to achieve salary equity: salary prediction (using various statistical procedures), counterparting (comparing salaries of persons of similar rank), and grievance procedures. (JT)

  19. Testosterone and Occupational Achievement.

    ERIC Educational Resources Information Center

    Dabbs, James M., Jr.

    1992-01-01

    Archival data on 4,462 military veterans linked higher levels of serum testosterone to lower-status occupations. A structural equation model was supported in which higher testosterone, mediated through lower intellectual ability, greater antisocial behavior, and lower education, leads away from white-collar occupations. Contains 49 references.…

  20. Guidance on Compatibility of UST Systems with Ethanol Blends Greater Than 10 Percent and Biodiesel Blends Greater Than 20 Percent

    EPA Pesticide Factsheets

    EPA guidance on complying with the federal compatibility requirement for underground storage tank (UST) systems storing gasoline containing greater than 10 percent ethanol or diesel containing greater than 20 percent biodiesel.

  1. Age or health status: which influences medical insurance enrollment greater?

    PubMed Central

    Xu, Wei; Cai, Gong–Jie; Li, Guan–Nan; Cao, Jing–Jing; Shi, Qiong–Hua; Bai, Jie

    2016-01-01

    Background The New Cooperative Medical Scheme (NCMS) for peasantries implemented in 2003 and the Urban Resident Basic Medical Insurance (URBMI) for the urban unemployed implemented in 2007 have many similarities. They both apply the financing mode of individual premiums plus government’s subsidies, and the voluntary enrollment. The Chinese government plans to integrate these two systems and build a unified basic medical insurance system for the unemployed in order to achieve the medical equity and increase the general health level. Thus, to analyze the main influencing factors of the enrollment of the urban unemployed and rural residents is very important for improving the system and securing the stability of the system during the transition. Methods The study uses data from the China Health and Nutrition Survey (CHNS) and adopts logistic regression models to test which factors influence the enrollment of the URBMI and the NCMS under the background of rather high enrollment rate of Chinese basic medical insurances and strong fiscal support of the Chinese government, especially whether health status or age influences enrollment of these two insurances greater. Results There is indeed some adverse selection in the URBMI and the NCMS. Whether the individual has chronic diseases have significant influence on enrollments of both the urban unemployed and rural residents, while whether the individual got ill in last four weeks just influences enrollments of the urban unemployed. Age influences enrollment greater than health status. The older the insured are, the larger the enrollment rates are. Conclusion Because of the active support for basic medical insurances of the Chinese government, the enrollment performance of the urban unemployed and rural residents has already changed. When implementing the new policy, the government should pay attention to the willingness to enroll in and the change of enrollment performance of the insured. Therefore, under the policy of

  2. Achieving quality assurance through clinical audit.

    PubMed

    Patel, Seraphim

    2010-06-01

    Audit is a crucial component of improvements to the quality of patient care. Clinical audits are undertaken to help ensure that patients can be given safe, reliable and dignified care, and to encourage them to self-direct their recovery. Such audits are undertaken also to help reduce lengths of patient stay in hospital, readmission rates and delays in discharge. This article describes the stages of clinical audit and the support required to achieve organisational core values.

  3. Reliability generalization of the Multigroup Ethnic Identity Measure-Revised (MEIM-R).

    PubMed

    Herrington, Hayley M; Smith, Timothy B; Feinauer, Erika; Griner, Derek

    2016-10-01

    [Correction Notice: An Erratum for this article was reported in Vol 63(5) of Journal of Counseling Psychology (see record 2016-33161-001). The name of author Erika Feinauer was misspelled as Erika Feinhauer. All versions of this article have been corrected.] Individuals' strength of ethnic identity has been linked with multiple positive indicators, including academic achievement and overall psychological well-being. The measure researchers use most often to assess ethnic identity, the Multigroup Ethnic Identity Measure (MEIM), underwent substantial revision in 2007. To inform scholars investigating ethnic identity, we performed a reliability generalization analysis on data from the revised version (MEIM-R) and compared it with data from the original MEIM. Random-effects weighted models evaluated internal consistency coefficients (Cronbach's alpha). Reliability coefficients for the MEIM-R averaged α = .88 across 37 samples, a statistically significant increase over the average of α = .84 for the MEIM across 75 studies. Reliability coefficients for the MEIM-R did not differ across study and participant characteristics such as sample gender and ethnic composition. However, consistently lower reliability coefficients averaging α = .81 were found among participants with low levels of education, suggesting that greater attention to data reliability is warranted when evaluating the ethnic identity of individuals such as middle-school students. Future research will be needed to ascertain whether data with other measures of aspects of personal identity (e.g., racial identity, gender identity) also differ as a function of participant level of education and associated cognitive or maturation processes. (PsycINFO Database Record

  4. Developing Ultra Reliable Life Support for the Moon and Mars

    NASA Technical Reports Server (NTRS)

    Jones, Harry W.

    2009-01-01

    Recycling life support systems can achieve ultra reliability by using spares to replace failed components. The added mass for spares is approximately equal to the original system mass, provided the original system reliability is not very low. Acceptable reliability can be achieved for the space shuttle and space station by preventive maintenance and by replacing failed units, However, this maintenance and repair depends on a logistics supply chain that provides the needed spares. The Mars mission must take all the needed spares at launch. The Mars mission also must achieve ultra reliability, a very low failure rate per hour, since it requires years rather than weeks and cannot be cut short if a failure occurs. Also, the Mars mission has a much higher mass launch cost per kilogram than shuttle or station. Achieving ultra reliable space life support with acceptable mass will require a well-planned and extensive development effort. Analysis must define the reliability requirement and allocate it to subsystems and components. Technologies, components, and materials must be designed and selected for high reliability. Extensive testing is needed to ascertain very low failure rates. Systems design should segregate the failure causes in the smallest, most easily replaceable parts. The systems must be designed, produced, integrated, and tested without impairing system reliability. Maintenance and failed unit replacement should not introduce any additional probability of failure. The overall system must be tested sufficiently to identify any design errors. A program to develop ultra reliable space life support systems with acceptable mass must start soon if it is to produce timely results for the moon and Mars.

  5. Improving Search Engine Reliability

    NASA Astrophysics Data System (ADS)

    Pruthi, Jyoti; Kumar, Ela

    2010-11-01

    Search engines on the Internet are used daily to access and find information. While these services are providing an easy way to find information globally, they are also suffering from artificially created false results. This paper describes two techniques that are being used to manipulate the search engines: spam pages (used to achieve higher rankings on the result page) and cloaking (used to feed falsified data into search engines). This paper also describes two proposed methods to fight this kind of misuse, algorithms for both of the formerly mentioned cases of spamdexing.

  6. Health equity and migrants in the Greater Mekong Subregion

    PubMed Central

    McMichael, Celia; Healy, Judith

    2017-01-01

    ABSTRACT Background: Migrant health is receiving increasing international attention, reflecting recognition of the health inequities experienced among many migrant populations and the need for health systems to adapt to diverse migrant populations. In the Greater Mekong Subregion (GMS) there is increasing migration associated with uneven economic integration and growth, socio-economic vulnerabilities, and disparities between countries. There has been limited progress, however, in improving migrant access to health services in the Subregion. This paper examines the health needs, access barriers, and policy responses to cross-border migrants in five GMS countries. Methods: A review of published literature and research was conducted on migrant health and health service access in Cambodia, Lao People’s Democratic Republic, Myanmar, Thailand, and Viet Nam, as well as analysis of current migration trends and universal health coverage (UHC) indicators in the Subregion. The review included different migrant types: i.e. migrant workers, irregular migrants, victims of trafficking, refugees and asylum seekers, and casual cross-border migrants. Results: There is substantial diversity in the capacity of GMS health systems to address migrant populations. Thailand has sought to enhance migrant health coverage, including development of migrant health policies/programs, bilateral migrant worker agreements, and migrant health insurance schemes; Viet Nam provides health protection for emigrant workers. Overall, however, access to good quality health care remains weak for many citizens in GMS countries let alone migrants. Migrant workers – and irregular migrants in particular – face elevated health risks yet are not adequately covered and incur high out-of-pocket (OOP) payments for health services. Conclusions: UHC implies equity: UHC is only achieved when everyone has the opportunity to access and use good-quality health care. Efforts to achieve UHC in the GMS require

  7. HiRel: Hybrid Automated Reliability Predictor (HARP) integrated reliability tool system, (version 7.0). Volume 2: HARP tutorial

    NASA Technical Reports Server (NTRS)

    Rothmann, Elizabeth; Dugan, Joanne Bechta; Trivedi, Kishor S.; Mittal, Nitin; Bavuso, Salvatore J.

    1994-01-01

    The Hybrid Automated Reliability Predictor (HARP) integrated Reliability (HiRel) tool system for reliability/availability prediction offers a toolbox of integrated reliability/availability programs that can be used to customize the user's application in a workstation or nonworkstation environment. The Hybrid Automated Reliability Predictor (HARP) tutorial provides insight into HARP modeling techniques and the interactive textual prompting input language via a step-by-step explanation and demonstration of HARP's fault occurrence/repair model and the fault/error handling models. Example applications are worked in their entirety and the HARP tabular output data are presented for each. Simple models are presented at first with each succeeding example demonstrating greater modeling power and complexity. This document is not intended to present the theoretical and mathematical basis for HARP.

  8. Low impact weight-bearing exercise in an upright posture achieves greater lumbopelvic stability than overground walking.

    PubMed

    Gibbon, K C; Debuse, D; Caplan, N

    2013-10-01

    The aim of this study was to determine the kinematic differences between movements on a new exercise device (EX) that promotes a stable trunk over a moving, unstable base of support, and overground walking (OW). Sixteen male participants performed EX and OW trials while their movements were tracked using a 3D motion capture system. Trunk and pelvis range of motion (ROM) were similar between EX and OW in the sagittal and frontal planes, and reduced for EX in the transverse plane. The pelvis was tilted anteriorly, on average, by about 16° in EX compared to OW. Hip and knee ROM were reduced in EX compared to OW. The exercise device appears to promote similar or reduced lumbopelvic motion, compared to walking, which could contribute to more tonic activity of the local lumbopelvic musculature.

  9. Academic Achievement through FLES: A Case for Promoting Greater Access to Foreign Language Study among Young Learners

    ERIC Educational Resources Information Center

    Taylor, Carolyn; Lafayette, Robert

    2010-01-01

    The No Child Left Behind Act of 2001 established foreign languages as a core curricular content area; however, instructional emphasis continues to be placed on curricular areas that factor into state educational accountability programs. The present study explored whether foreign language study of first-year Grade 3 foreign language students who…

  10. Achieving Greater Feedback and Flexibility Using Online Pre-Laboratory Exercises with Non-Major Chemistry Students

    ERIC Educational Resources Information Center

    Chittleborough, Gail D.; Mocerino, Mauro; Treagust, David F.

    2007-01-01

    The design and effects of using online pre-laboratory exercises in an introductory first-year university chemistry course that requires no previous knowledge of chemistry for non-major chemistry students is reported. The results have indicated that the majority of students involved in the study considered that their learning opportunities were…

  11. Reliability correction for functional connectivity: Theory and implementation.

    PubMed

    Mueller, Sophia; Wang, Danhong; Fox, Michael D; Pan, Ruiqi; Lu, Jie; Li, Kuncheng; Sun, Wei; Buckner, Randy L; Liu, Hesheng

    2015-11-01

    Network properties can be estimated using functional connectivity MRI (fcMRI). However, regional variation of the fMRI signal causes systematic biases in network estimates including correlation attenuation in regions of low measurement reliability. Here we computed the spatial distribution of fcMRI reliability using longitudinal fcMRI datasets and demonstrated how pre-estimated reliability maps can correct for correlation attenuation. As a test case of reliability-based attenuation correction we estimated properties of the default network, where reliability was significantly lower than average in the medial temporal lobe and higher in the posterior medial cortex, heterogeneity that impacts estimation of the network. Accounting for this bias using attenuation correction revealed that the medial temporal lobe's contribution to the default network is typically underestimated. To render this approach useful to a greater number of datasets, we demonstrate that test-retest reliability maps derived from repeated runs within a single scanning session can be used as a surrogate for multi-session reliability mapping. Using data segments with different scan lengths between 1 and 30 min, we found that test-retest reliability of connectivity estimates increases with scan length while the spatial distribution of reliability is relatively stable even at short scan lengths. Finally, analyses of tertiary data revealed that reliability distribution is influenced by age, neuropsychiatric status and scanner type, suggesting that reliability correction may be especially important when studying between-group differences. Collectively, these results illustrate that reliability-based attenuation correction is an easily implemented strategy that mitigates certain features of fMRI signal nonuniformity.

  12. Aligning Items and Achievement Levels: A Study Comparing Expert Judgments

    ERIC Educational Resources Information Center

    Kaliski, Pamela; Huff, Kristen; Barry, Carol

    2011-01-01

    For educational achievement tests that employ multiple-choice (MC) items and aim to reliably classify students into performance categories, it is critical to design MC items that are capable of discriminating student performance according to the stated achievement levels. This is accomplished, in part, by clearly understanding how item design…

  13. Reliability of Wireless Sensor Networks

    PubMed Central

    Dâmaso, Antônio; Rosa, Nelson; Maciel, Paulo

    2014-01-01

    Wireless Sensor Networks (WSNs) consist of hundreds or thousands of sensor nodes with limited processing, storage, and battery capabilities. There are several strategies to reduce the power consumption of WSN nodes (by increasing the network lifetime) and increase the reliability of the network (by improving the WSN Quality of Service). However, there is an inherent conflict between power consumption and reliability: an increase in reliability usually leads to an increase in power consumption. For example, routing algorithms can send the same packet though different paths (multipath strategy), which it is important for reliability, but they significantly increase the WSN power consumption. In this context, this paper proposes a model for evaluating the reliability of WSNs considering the battery level as a key factor. Moreover, this model is based on routing algorithms used by WSNs. In order to evaluate the proposed models, three scenarios were considered to show the impact of the power consumption on the reliability of WSNs. PMID:25157553

  14. Nuclear weapon reliability evaluation methodology

    SciTech Connect

    Wright, D.L.

    1993-06-01

    This document provides an overview of those activities that are normally performed by Sandia National Laboratories to provide nuclear weapon reliability evaluations for the Department of Energy. These reliability evaluations are first provided as a prediction of the attainable stockpile reliability of a proposed weapon design. Stockpile reliability assessments are provided for each weapon type as the weapon is fielded and are continuously updated throughout the weapon stockpile life. The reliability predictions and assessments depend heavily on data from both laboratory simulation and actual flight tests. An important part of the methodology are the opportunities for review that occur throughout the entire process that assure a consistent approach and appropriate use of the data for reliability evaluation purposes.

  15. Reliable measurement of the receding contact angle.

    PubMed

    Korhonen, Juuso T; Huhtamäki, Tommi; Ikkala, Olli; Ras, Robin H A

    2013-03-26

    Surface wettability is usually evaluated by the contact angle between the perimeter of a water drop and the surface. However, this single measurement is not enough for proper characterization, and the so-called advancing and receding contact angles also need to be measured. Measuring the receding contact angle can be challenging, especially for extremely hydrophobic surfaces. We demonstrate a reliable procedure by using the common needle-in-the-sessile-drop method. Generally, the contact line movement needs to be followed, and true receding movement has to be distinguished from "pseudo-movement" occurring before the receding angle is reached. Depending on the contact angle hysteresis, the initial size of the drop may need to be surprisingly large to achieve a reliable result. Although our motivation for this work was the characterization of superhydrophobic surfaces, we also show that this method works universally ranging from hydrophilic to superhydrophobic surfaces.

  16. Reliability of large superconducting magnets through design

    NASA Astrophysics Data System (ADS)

    Henning, C. D.

    1980-09-01

    As superconducting magnet systems grow larger and become the central component of major systems involving fusion, magnetohydrodynamics, and high energy physics, their reliability must be commensurate with the enormous capital investment in the project. Creative design is the most effective way of ensuring magnet reliability and providing a reasonable limit on the amount of quality control needed. By subjecting the last drawing operation in superconductor manufacture to a stress larger than the magnet design stress, a 100 percent proof test is achieved; cabled conductors offer mechanical redundancy, as do some methods of conductor joining; ground plane insulation should be multilayered to prevent arcs, and interturn and interlayer insulation spaced to be compatible with the self-extinguishing of arcs during quench voltages; electrical leads should be thermally protected; and guard vacuum spaces can be incorporated to control helium leaks.

  17. Probabilistic Methods for Structural Design and Reliability

    NASA Technical Reports Server (NTRS)

    Chamis, Christos C.; Whitlow, Woodrow, Jr. (Technical Monitor)

    2002-01-01

    This report describes a formal method to quantify structural damage tolerance and reliability in the presence of a multitude of uncertainties in turbine engine components. The method is based at the material behavior level where primitive variables with their respective scatter ranges are used to describe behavior. Computational simulation is then used to propagate the uncertainties to the structural scale where damage tolerance and reliability are usually specified. Several sample cases are described to illustrate the effectiveness, versatility, and maturity of the method. Typical results from this method demonstrate, that it is mature and that it can be used to probabilistically evaluate turbine engine structural components. It may be inferred from the results that the method is suitable for probabilistically predicting the remaining life in aging or in deteriorating structures, for making strategic projections and plans, and for achieving better, cheaper, faster products that give competitive advantages in world markets.

  18. Optimal Implementations for Reliable Circadian Clocks

    NASA Astrophysics Data System (ADS)

    Hasegawa, Yoshihiko; Arita, Masanori

    2014-09-01

    Circadian rhythms are acquired through evolution to increase the chances for survival through synchronizing with the daylight cycle. Reliable synchronization is realized through two trade-off properties: regularity to keep time precisely, and entrainability to synchronize the internal time with daylight. We find by using a phase model with multiple inputs that achieving the maximal limit of regularity and entrainability entails many inherent features of the circadian mechanism. At the molecular level, we demonstrate the role sharing of two light inputs, phase advance and delay, as is well observed in mammals. At the behavioral level, the optimal phase-response curve inevitably contains a dead zone, a time during which light pulses neither advance nor delay the clock. We reproduce the results of phase-controlling experiments entrained by two types of periodic light pulses. Our results indicate that circadian clocks are designed optimally for reliable clockwork through evolution.

  19. Reliable avionics design for deep space

    NASA Astrophysics Data System (ADS)

    Johnson, Stephen B.

    The technical and organizational problems posed by the Space Exploration Initiative (SEI) are discussed, and some possible solutions are examined. It is pointed out that SEI poses a whole new set of challenging problems in the design of reliable systems. These missions and their corresponding systems are far more complex than current systems. The initiative requires a set of vehicles and systems which must have very high levels of autonomy, reliability, and operability for long periods of time. It is emphasized that to achieve these goals in the face of great complexity, new technologies and organizational techniques will be necessary. It is noted that the key to a good design is good people. Not only must good people be found, but they must be placed in positions appropriate to their skills. It is argued that the atomistic and autocratic paradigm of vertical organizations must be replaced with more team-oriented and democratic structures.

  20. The Albanian National Question and the Myth of Greater Albania

    DTIC Science & Technology

    2013-03-01

    minister of Greece, “neither race, nor language, nor skull could be used as the basis for determining the nationality and that national conscience...Serbia, in particular, has been very active in spreading propaganda about the danger posed by the prospect of Greater Albania. The term, alien to the...greater Albania plot.”62 However, for Albanians, despite of their living place, the term “Greater Albania” is alien .63 Instead, they use the term

  1. Obtaining Greater Efficiency and Productivity in Defense Spending

    DTIC Science & Technology

    2011-08-23

    Obtaining Greater Efficiency and Productivity in Defense Spending Gold Coast Conference Tim Dowd Director for Contracts Space and Naval...Greater Efficiency and Productivity in Defense Spending 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...Obtaining Greater Efficiency and Productivity in Defense Spending ” 5   Present a competitive strategy at each program milestone *   Remove

  2. SALT and Spelling Achievement.

    ERIC Educational Resources Information Center

    Nelson, Joan

    A study investigated the effects of suggestopedic accelerative learning and teaching (SALT) on the spelling achievement, attitudes toward school, and memory skills of fourth-grade students. Subjects were 20 male and 28 female students from two self-contained classrooms at Kennedy Elementary School in Rexburg, Idaho. The control classroom and the…

  3. Iowa Women of Achievement.

    ERIC Educational Resources Information Center

    Ohrn, Deborah Gore, Ed.

    1993-01-01

    This issue of the Goldfinch highlights some of Iowa's 20th century women of achievement. These women have devoted their lives to working for human rights, education, equality, and individual rights. They come from the worlds of politics, art, music, education, sports, business, entertainment, and social work. They represent Native Americans,…

  4. Schools Achieving Gender Equity.

    ERIC Educational Resources Information Center

    Revis, Emma

    This guide is designed to assist teachers presenting the Schools Achieving Gender Equity (SAGE) curriculum for vocational education students, which was developed to align gender equity concepts with the Kentucky Education Reform Act (KERA). Included in the guide are lesson plans for classes on the following topics: legal issues of gender equity,…

  5. Achieving Peace through Education.

    ERIC Educational Resources Information Center

    Clarken, Rodney H.

    While it is generally agreed that peace is desirable, there are barriers to achieving a peaceful world. These barriers are classified into three major areas: (1) an erroneous view of human nature; (2) injustice; and (3) fear of world unity. In a discussion of these barriers, it is noted that although the consciousness and conscience of the world…

  6. Explorations in achievement motivation

    NASA Technical Reports Server (NTRS)

    Helmreich, Robert L.

    1982-01-01

    Recent research on the nature of achievement motivation is reviewed. A three-factor model of intrinsic motives is presented and related to various criteria of performance, job satisfaction and leisure activities. The relationships between intrinsic and extrinsic motives are discussed. Needed areas for future research are described.

  7. Appraising Reading Achievement.

    ERIC Educational Resources Information Center

    Ediger, Marlow

    To determine quality sequence in pupil progress, evaluation approaches need to be used which guide the teacher to assist learners to attain optimally. Teachers must use a variety of procedures to appraise student achievement in reading, because no one approach is adequate. Appraisal approaches might include: (1) observation and subsequent…

  8. Cognitive Processes and Achievement.

    ERIC Educational Resources Information Center

    Hunt, Dennis; Randhawa, Bikkar S.

    For a group of 165 fourth- and fifth-grade students, four achievement test scores were correlated with success on nine tests designed to measure three cognitive functions: sustained attention, successive processing, and simultaneous processing. This experiment was designed in accordance with Luria's model of the three functional units of the…

  9. Graders' Mathematics Achievement

    ERIC Educational Resources Information Center

    Bond, John B.; Ellis, Arthur K.

    2013-01-01

    The purpose of this experimental study was to investigate the effects of metacognitive reflective assessment instruction on student achievement in mathematics. The study compared the performance of 141 students who practiced reflective assessment strategies with students who did not. A posttest-only control group design was employed, and results…

  10. Achieving All Our Ambitions

    ERIC Educational Resources Information Center

    Hartley, Tricia

    2009-01-01

    National learning and skills policy aims both to build economic prosperity and to achieve social justice. Participation in higher education (HE) has the potential to contribute substantially to both aims. That is why the Campaign for Learning has supported the ambition to increase the proportion of the working-age population with a Level 4…

  11. Improving Educational Achievement.

    ERIC Educational Resources Information Center

    New York University Education Quarterly, 1979

    1979-01-01

    This is a slightly abridged version of the report of the National Academy of Education panel, convened at the request of HEW Secretary Joseph Califano and Assistant Secretary for Education Mary F. Berry, to study recent declines in student achievement and methods of educational improvement. (SJL)

  12. The Achievement Club

    ERIC Educational Resources Information Center

    Rogers, Ibram

    2009-01-01

    When Gabrielle Carpenter became a guidance counselor in Northern Virginia nine years ago, she focused on the academic achievement gap and furiously tried to close it. At first, she was compelled by tremendous professional interest. However, after seeing her son lose his zeal for school, Carpenter joined forces with other parents to form an…

  13. Achievement in Problem Solving

    ERIC Educational Resources Information Center

    Friebele, David

    2010-01-01

    This Action Research Project is meant to investigate the effects of incorporating research-based instructional strategies into instruction and their subsequent effect on student achievement in the area of problem-solving. The two specific strategies utilized are the integration of manipulatives and increased social interaction on a regular basis.…

  14. Essays on Educational Achievement

    ERIC Educational Resources Information Center

    Ampaabeng, Samuel Kofi

    2013-01-01

    This dissertation examines the determinants of student outcomes--achievement, attainment, occupational choices and earnings--in three different contexts. The first two chapters focus on Ghana while the final chapter focuses on the US state of Massachusetts. In the first chapter, I exploit the incidence of famine and malnutrition that resulted to…

  15. Advancing Student Achievement

    ERIC Educational Resources Information Center

    Walberg, Herbert J.

    2010-01-01

    For the last half century, higher spending and many modern reforms have failed to raise the achievement of students in the United States to the levels of other economically advanced countries. A possible explanation, says Herbert Walberg, is that much current education theory is ill informed about scientific psychology, often drawing on fads and…

  16. NCLB: Achievement Robin Hood?

    ERIC Educational Resources Information Center

    Bracey, Gerald W.

    2008-01-01

    In his "Wall Street Journal" op-ed on the 25th of anniversary of "A Nation At Risk", former assistant secretary of education Chester E. Finn Jr. applauded the report for turning U.S. education away from equality and toward achievement. It was not surprising, then, that in mid-2008, Finn arranged a conference to examine the…

  17. Nuclear electric propulsion operational reliability and crew safety study: NEP systems/modeling report

    NASA Technical Reports Server (NTRS)

    Karns, James

    1993-01-01

    The objective of this study was to establish the initial quantitative reliability bounds for nuclear electric propulsion systems in a manned Mars mission required to ensure crew safety and mission success. Finding the reliability bounds involves balancing top-down (mission driven) requirements and bottom-up (technology driven) capabilities. In seeking this balance we hope to accomplish the following: (1) provide design insights into the achievability of the baseline design in terms of reliability requirements, given the existing technology base; (2) suggest alternative design approaches which might enhance reliability and crew safety; and (3) indicate what technology areas require significant research and development to achieve the reliability objectives.

  18. A fourth generation reliability predictor

    NASA Technical Reports Server (NTRS)

    Bavuso, Salvatore J.; Martensen, Anna L.

    1988-01-01

    A reliability/availability predictor computer program has been developed and is currently being beta-tested by over 30 US companies. The computer program is called the Hybrid Automated Reliability Predictor (HARP). HARP was developed to fill an important gap in reliability assessment capabilities. This gap was manifested through the use of its third-generation cousin, the Computer-Aided Reliability Estimation (CARE III) program, over a six-year development period and an additional three-year period during which CARE III has been in the public domain. The accumulated experience of the over 30 establishments now using CARE III was used in the development of the HARP program.

  19. Silver plating ensures reliable diffusion bonding of dissimilar metals

    NASA Technical Reports Server (NTRS)

    1967-01-01

    Dissimilar metals are reliably joined by diffusion bonding when the surfaces are electroplated with silver. The process involves cleaning and etching, anodization, silver striking, and silver plating with a conventional plating bath. It minimizes the formation of detrimental intermetallic phases and provides greater tolerance of processing parameters.

  20. RF-MEMS capacitive switches with high reliability

    DOEpatents

    Goldsmith, Charles L.; Auciello, Orlando H.; Carlisle, John A.; Sampath, Suresh; Sumant, Anirudha V.; Carpick, Robert W.; Hwang, James; Mancini, Derrick C.; Gudeman, Chris

    2013-09-03

    A reliable long life RF-MEMS capacitive switch is provided with a dielectric layer comprising a "fast discharge diamond dielectric layer" and enabling rapid switch recovery, dielectric layer charging and discharging that is efficient and effective to enable RF-MEMS switch operation to greater than or equal to 100 billion cycles.

  1. The process group approach to reliable distributed computing

    NASA Technical Reports Server (NTRS)

    Birman, Kenneth P.

    1992-01-01

    The difficulty of developing reliable distribution software is an impediment to applying distributed computing technology in many settings. Experience with the ISIS system suggests that a structured approach based on virtually synchronous process groups yields systems that are substantially easier to develop, exploit sophisticated forms of cooperative computation, and achieve high reliability. Six years of research on ISIS, describing the model, its implementation challenges, and the types of applications to which ISIS has been applied are reviewed.

  2. Survey of Software Assurance Techniques for Highly Reliable Systems

    NASA Technical Reports Server (NTRS)

    Nelson, Stacy

    2004-01-01

    This document provides a survey of software assurance techniques for highly reliable systems including a discussion of relevant safety standards for various industries in the United States and Europe, as well as examples of methods used during software development projects. It contains one section for each industry surveyed: Aerospace, Defense, Nuclear Power, Medical Devices and Transportation. Each section provides an overview of applicable standards and examples of a mission or software development project, software assurance techniques used and reliability achieved.

  3. Research Opportunities in Reliability of Photovoltaic Modules (Presentation)

    SciTech Connect

    Hacke, P.

    2010-05-01

    The motivation for an increased scope and a more proactive effort in reliability research of photovoltaic modules and systems includes reducing the levelized cost of energy and gaining better confidence in the energy and financial payback for photovoltaic systems. This increased reliability and confidence will lead to greater penetration of photovoltaics in the energy portfolio and greater employment in photovoltaics and related industries. Present research needs include the fundamental degradation mechanisms of polymers, connectors and other module components, mapping of failure mechanisms observed in the field to those in accelerated lifetime tests, determining the acceleration factors, and improving standards for modules such that tests can appropriately be assigned to evaluate their long term durability. Specific mechanisms discussed are corrosion in module components, metastability in thin-film active layers, delamination and loss of elastic properties in module polymeric materials, and inverter failure. Presently, there is hiring of reliability scientists and engineers at many levels of the value chain for photovoltaics.

  4. Shunt capacitor effect on electrical distribution system reliability

    NASA Astrophysics Data System (ADS)

    Sallam, Abdelhay A.; Desouky, Mohamed; Desouky, Hussien

    1994-03-01

    To improve the security & reliability of a distribution system, as much power as feasible must go through a given transmission line. This can be achieved by using shunt capacitors as compensators. These shunt capacitive compensators improve the load carrying capability of the line by controlling the reactive power flow. Consequently, the capacitor existence can not be ignored in evaluating system reliability. The paper applies the state-space method to calculate the reliability indices for compensated & uncompensated systems with different success criteria. The importance of using shunt capacitors to improve the level of distribution system reliability is illustrated in addition to their original function as reactive power controllers. Our procedure, based on a Markov process, is applied to a numerical example, and indicates that system reliability is improved when using shunt capacitors.

  5. Reliability Impacts in Life Support Architecture and Technology Selection

    NASA Technical Reports Server (NTRS)

    Lange Kevin E.; Anderson, Molly S.

    2012-01-01

    Quantitative assessments of system reliability and equivalent system mass (ESM) were made for different life support architectures based primarily on International Space Station technologies. The analysis was applied to a one-year deep-space mission. System reliability was increased by adding redundancy and spares, which added to the ESM. Results were thus obtained allowing a comparison of the ESM for each architecture at equivalent levels of reliability. Although the analysis contains numerous simplifications and uncertainties, the results suggest that achieving necessary reliabilities for deep-space missions will add substantially to the life support ESM and could influence the optimal degree of life support closure. Approaches for reducing reliability impacts were investigated and are discussed.

  6. 5 CFR 630.1210 - Greater leave entitlements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND LEAVE Family and Medical Leave § 630.1210 Greater leave entitlements. (a) An agency shall comply... greater family or medical leave entitlements to employees than those provided under this subpart. Nothing... or regulation. (d) The entitlements under sections 6381 through 6387 of title 5, United States...

  7. Strategies for Talent Management: Greater Philadelphia Companies in Action

    ERIC Educational Resources Information Center

    Council for Adult and Experiential Learning (NJ1), 2008

    2008-01-01

    Human capital is one of the critical issues that impacts the Greater Philadelphia region's ability to grow and prosper. The CEO Council for Growth (CEO Council) is committed to ensuring a steady and talented supply of quality workers for this region. "Strategies for Talent Management: Greater Philadelphia Companies in Action" provides…

  8. Comparative Education in Greater China: Contexts, Characteristics, Contrasts and Contributions.

    ERIC Educational Resources Information Center

    Bray, Mark; Qin, Gui

    2001-01-01

    The evolution of comparative education in Greater China (mainland China, Taiwan, Hong Kong, and Macau) has been influenced by size, culture, political ideologies, standard of living, and colonialism. Similarities and differences in conceptions of comparative education are identified among the four components and between Greater China and other…

  9. Faculty achievement tracking tool.

    PubMed

    Pettus, Sarah; Reifschneider, Ellen; Burruss, Nancy

    2009-03-01

    Faculty development and scholarship is an expectation of nurse educators. Accrediting institutions, such as the Commission on Collegiate Nursing Education, the National League for Nursing Accrediting Commission, and the Higher Learning Commission, all have criteria regarding faculty achievement. A faculty achievement tracking tool (FATT) was developed to facilitate documentation of accreditation criteria attainment. Based on criteria from accrediting organizations, the roles that are addressed include scholarship, service, and practice. Definitions and benchmarks for the faculty as an aggregate are included. Undergoing reviews from different accrediting organizations, the FATT has been used once for accreditation of the undergraduate program and once for accreditation of the graduate program. The FATT is easy to use and has become an excellent adjunct for the preparation for accreditation reports. In addition, the FATT may be used for yearly evaluations, advancement, and merit.

  10. Project ACHIEVE final report

    SciTech Connect

    1997-06-13

    Project ACHIEVE was a math/science academic enhancement program aimed at first year high school Hispanic American students. Four high schools -- two in El Paso, Texas and two in Bakersfield, California -- participated in this Department of Energy-funded program during the spring and summer of 1996. Over 50 students, many of whom felt they were facing a nightmare future, were given the opportunity to work closely with personal computers and software, sophisticated calculators, and computer-based laboratories -- an experience which their regular academic curriculum did not provide. Math and science projects, exercises, and experiments were completed that emphasized independent and creative applications of scientific and mathematical theories to real world problems. The most important outcome was the exposure Project ACHIEVE provided to students concerning the college and technical-field career possibilities available to them.

  11. Electrical insulation design requirements and reliability goals

    NASA Astrophysics Data System (ADS)

    Ross, R. G., Jr.

    1983-11-01

    The solar cells in a photovoltaic module which must be electrically isolated from module exterior surfaces to satisfy a variety of safety and operating considerations are discussed. The performance and reliability of the insulation system are examined. Technical requirements involve the capability of withstanding the differential voltage from the solar cells to the module frame. The maximum system voltage includes consideration of maximum open circuit array voltages achieved under low-temperature, high-irradiance conditions, and transient overvoltages due to system feedback of lightning transients. The latter is bounded by the characteristics of incorporated voltage limiting devices such as MOVs.

  12. Reliability of large superconducting magnets through design

    NASA Astrophysics Data System (ADS)

    Henning, C. D.

    1981-01-01

    Design and quality control of large superconducting magnets for reliability comparable to pressure vessels are discussed. The failure modes are analyzed including thermoelectric instabilities, electrical shorts, cryogenic/vacuum defects, and mechanical malfunctions. Design must take into consideration conductor stability, insulation based on the Paschen curves, and the possible burnout of cryogenic transition leads if the He flow is interrupted. The final stage of the metal drawing process should stress the superconductor material to a stress value higher than the magnet design stress, cabled conductors should be used to achieve mechanical redundancy, and ground-plane insulation must be multilayered for arc prevention.

  13. A Vision for Spaceflight Reliability: NASA's Objectives Based Strategy

    NASA Technical Reports Server (NTRS)

    Groen, Frank; Evans, John; Hall, Tony

    2015-01-01

    In defining the direction for a new Reliability and Maintainability standard, OSMA has extracted the essential objectives that our programs need, to undertake a reliable mission. These objectives have been structured to lead mission planning through construction of an objective hierarchy, which defines the critical approaches for achieving high reliability and maintainability (R M). Creating a hierarchy, as a basis for assurance implementation, is a proven approach; yet, it holds the opportunity to enable new directions, as NASA moves forward in tackling the challenges of space exploration.

  14. Stirling Convertor Fasteners Reliability Quantification

    NASA Technical Reports Server (NTRS)

    Shah, Ashwin R.; Korovaichuk, Igor; Kovacevich, Tiodor; Schreiber, Jeffrey G.

    2006-01-01

    Onboard Radioisotope Power Systems (RPS) being developed for NASA s deep-space science and exploration missions require reliable operation for up to 14 years and beyond. Stirling power conversion is a candidate for use in an RPS because it offers a multifold increase in the conversion efficiency of heat to electric power and reduced inventory of radioactive material. Structural fasteners are responsible to maintain structural integrity of the Stirling power convertor, which is critical to ensure reliable performance during the entire mission. Design of fasteners involve variables related to the fabrication, manufacturing, behavior of fasteners and joining parts material, structural geometry of the joining components, size and spacing of fasteners, mission loads, boundary conditions, etc. These variables have inherent uncertainties, which need to be accounted for in the reliability assessment. This paper describes these uncertainties along with a methodology to quantify the reliability, and provides results of the analysis in terms of quantified reliability and sensitivity of Stirling power conversion reliability to the design variables. Quantification of the reliability includes both structural and functional aspects of the joining components. Based on the results, the paper also describes guidelines to improve the reliability and verification testing.

  15. The Reliability of Density Measurements.

    ERIC Educational Resources Information Center

    Crothers, Charles

    1978-01-01

    Data from a land-use study of small- and medium-sized towns in New Zealand are used to ascertain the relationship between official and effective density measures. It was found that the reliability of official measures of density is very low overall, although reliability increases with community size. (Author/RLV)

  16. Computer-Aided Reliability Estimation

    NASA Technical Reports Server (NTRS)

    Bavuso, S. J.; Stiffler, J. J.; Bryant, L. A.; Petersen, P. L.

    1986-01-01

    CARE III (Computer-Aided Reliability Estimation, Third Generation) helps estimate reliability of complex, redundant, fault-tolerant systems. Program specifically designed for evaluation of fault-tolerant avionics systems. However, CARE III general enough for use in evaluation of other systems as well.

  17. The Validity of Reliability Measures.

    ERIC Educational Resources Information Center

    Seddon, G. M.

    1988-01-01

    Demonstrates that some commonly used indices can be misleading in their quantification of reliability. The effects are most pronounced on gain or difference scores. Proposals are made to avoid sources of invalidity by using a procedure to assess reliability in terms of upper and lower limits for the true scores of each examinee. (Author/JDH)

  18. Reliability in CMOS IC processing

    NASA Technical Reports Server (NTRS)

    Shreeve, R.; Ferrier, S.; Hall, D.; Wang, J.

    1990-01-01

    Critical CMOS IC processing reliability monitors are defined in this paper. These monitors are divided into three categories: process qualifications, ongoing production workcell monitors, and ongoing reliability monitors. The key measures in each of these categories are identified and prioritized based on their importance.

  19. Essay Reliability: Form and Meaning.

    ERIC Educational Resources Information Center

    Shale, Doug

    This study is an attempt at a cohesive characterization of the concept of essay reliability. As such, it takes as a basic premise that previous and current practices in reporting reliability estimates for essay tests have certain shortcomings. The study provides an analysis of these shortcomings--partly to encourage a fuller understanding of the…

  20. Reliability-based design optimization using efficient global reliability analysis.

    SciTech Connect

    Bichon, Barron J.; Mahadevan, Sankaran; Eldred, Michael Scott

    2010-05-01

    Finding the optimal (lightest, least expensive, etc.) design for an engineered component that meets or exceeds a specified level of reliability is a problem of obvious interest across a wide spectrum of engineering fields. Various methods for this reliability-based design optimization problem have been proposed. Unfortunately, this problem is rarely solved in practice because, regardless of the method used, solving the problem is too expensive or the final solution is too inaccurate to ensure that the reliability constraint is actually satisfied. This is especially true for engineering applications involving expensive, implicit, and possibly nonlinear performance functions (such as large finite element models). The Efficient Global Reliability Analysis method was recently introduced to improve both the accuracy and efficiency of reliability analysis for this type of performance function. This paper explores how this new reliability analysis method can be used in a design optimization context to create a method of sufficient accuracy and efficiency to enable the use of reliability-based design optimization as a practical design tool.

  1. Photovoltaic performance and reliability workshop

    SciTech Connect

    Mrig, L.

    1993-12-01

    This workshop was the sixth in a series of workshops sponsored by NREL/DOE under the general subject of photovoltaic testing and reliability during the period 1986--1993. PV performance and PV reliability are at least as important as PV cost, if not more. In the US, PV manufacturers, DOE laboratories, electric utilities, and others are engaged in the photovoltaic reliability research and testing. This group of researchers and others interested in the field were brought together to exchange the technical knowledge and field experience as related to current information in this evolving field of PV reliability. The papers presented here reflect this effort since the last workshop held in September, 1992. The topics covered include: cell and module characterization, module and system testing, durability and reliability, system field experience, and standards and codes.

  2. Statistical modeling of software reliability

    NASA Technical Reports Server (NTRS)

    Miller, Douglas R.

    1992-01-01

    This working paper discusses the statistical simulation part of a controlled software development experiment being conducted under the direction of the System Validation Methods Branch, Information Systems Division, NASA Langley Research Center. The experiment uses guidance and control software (GCS) aboard a fictitious planetary landing spacecraft: real-time control software operating on a transient mission. Software execution is simulated to study the statistical aspects of reliability and other failure characteristics of the software during development, testing, and random usage. Quantification of software reliability is a major goal. Various reliability concepts are discussed. Experiments are described for performing simulations and collecting appropriate simulated software performance and failure data. This data is then used to make statistical inferences about the quality of the software development and verification processes as well as inferences about the reliability of software versions and reliability growth under random testing and debugging.

  3. The Influence of Teacher Graduate Degrees on Student Reading Achievement

    ERIC Educational Resources Information Center

    Badgett, Kevin; Decman, John; Carman, Carol

    2014-01-01

    In a time of limited means and continued calls for higher student achievement, school leaders need to be wise in their use of resources. Earlier research has called for greater levels of teacher preparation, and, while many school districts provide greater compensation for teachers with graduate degrees, some districts have begun phasing out this…

  4. Software Reliability, Measurement, and Testing Software Reliability and Test Integration

    DTIC Science & Technology

    1992-04-01

    process rariables on software reliability A guidebook was produced to help pro- gram managers control and manage softwar~e reliability and testing...Integrated Reliability Management System "IRMS" 17 1.6 Organization of Report 17 2.0 SURVEYS 20 2.1 Software Projects Survey 20 2.1.1 Candidate Projects...Systems 103 4.2.2.3 Compiler 103 4.2.2.4 Data Management and Analysis 103 4.2.3 Test/Support Tools 103 4.2.3.1 DEC Test Manager 103 4.2.3.2 SDDL 103

  5. Learning reliable manipulation strategies without initial physical models

    NASA Technical Reports Server (NTRS)

    Christiansen, Alan D.; Mason, Matthew T.; Mitchell, Tom M.

    1990-01-01

    A description is given of a robot, possessing limited sensory and effectory capabilities but no initial model of the effects of its actions on the world, that acquires such a model through exploration, practice, and observation. By acquiring an increasingly correct model of its actions, it generates increasingly successful plans to achieve its goals. In an apparently nondeterministic world, achieving reliability requires the identification of reliable actions and a preference for using such actions. Furthermore, by selecting its training actions carefully, the robot can significantly improve its learning rate.

  6. "Reliability generalization of the Multigroup Ethnic Identity Measure-Revised (MEIM-R)": Correction to Herrington et al. (2016).

    PubMed

    2016-10-01

    Reports an error in "Reliability Generalization of the Multigroup Ethnic Identity Measure-Revised (MEIM-R)" by Hayley M. Herrington, Timothy B. Smith, Erika Feinauer and Derek Griner (Journal of Counseling Psychology, Advanced Online Publication, Mar 17, 2016, np). The name of author Erika Feinauer was misspelled as Erika Feinhauer. All versions of this article have been corrected. (The following abstract of the original article appeared in record 2016-13160-001.) Individuals' strength of ethnic identity has been linked with multiple positive indicators, including academic achievement and overall psychological well-being. The measure researchers use most often to assess ethnic identity, the Multigroup Ethnic Identity Measure (MEIM), underwent substantial revision in 2007. To inform scholars investigating ethnic identity, we performed a reliability generalization analysis on data from the revised version (MEIM-R) and compared it with data from the original MEIM. Random-effects weighted models evaluated internal consistency coefficients (Cronbach's alpha). Reliability coefficients for the MEIM-R averaged α = .88 across 37 samples, a statistically significant increase over the average of α = .84 for the MEIM across 75 studies. Reliability coefficients for the MEIM-R did not differ across study and participant characteristics such as sample gender and ethnic composition. However, consistently lower reliability coefficients averaging α = .81 were found among participants with low levels of education, suggesting that greater attention to data reliability is warranted when evaluating the ethnic identity of individuals such as middle-school students. Future research will be needed to ascertain whether data with other measures of aspects of personal identity (e.g., racial identity, gender identity) also differ as a function of participant level of education and associated cognitive or maturation processes. (PsycINFO Database Record

  7. Influence of Delhi Pollution on Aerosol Properties Over Greater Noida

    NASA Astrophysics Data System (ADS)

    Sharma, M.; Singh, R. P.; Kumar, R.

    2015-12-01

    Influence of Delhi Pollution on Aerosol Properties over Greater NoidaManish Sharma1, Ramesh P. Singh2 and Rajesh Kumar3 1Research and Technology Development Centre, Sharda University, Greater Noida, India. 2School of Earth and Environmental Sciences, Schmid College of Science, Chapman University, Orange 92866, USA 3School of Basic Sciences and Research, Sharda University, Greater Noida, India. Delhi capital of India is highly polluted during winter and summer seasons. Due to dominant westerly winds the air mass influence its neighboring city Greater Noida which is located 60 km south east of Delhi. Detailed analysis of multi satellite data and ground observations have been carried out during 2001-2015. The ground observation and satellite data show dynamic aerosol optical parameters over Greater Noida. During winter and summer seasons, dominant westerly wind outflow pollutants of Delhi that mix with the local anthropogenic emissions of Greater Noida influencing aerosol properties at different pressure levels. The characteristics of trace gases and aerosol parameters over Delhi and Greater Noida will be presented. The air quality is severely affected from the outflow of pollutants from Delhi which is threat to people living in the area. Due to dominant winds the air mass further transported towards eastern parts of Indo-Gangetic plains affecting weather conditions of the major cities.

  8. A reliable multicast for XTP

    NASA Technical Reports Server (NTRS)

    Dempsey, Bert J.; Weaver, Alfred C.

    1990-01-01

    Multicast services needed for current distributed applications on LAN's fall generally into one of three categories: datagram, semi-reliable, and reliable. Transport layer multicast datagrams represent unreliable service in which the transmitting context 'fires and forgets'. XTP executes these semantics when the MULTI and NOERR mode bits are both set. Distributing sensor data and other applications in which application-level error recovery strategies are appropriate benefit from the efficiency in multidestination delivery offered by datagram service. Semi-reliable service refers to multicasting in which the control algorithms of the transport layer--error, flow, and rate control--are used in transferring the multicast distribution to the set of receiving contexts, the multicast group. The multicast defined in XTP provides semi-reliable service. Since, under a semi-reliable service, joining a multicast group means listening on the group address and entails no coordination with other members, a semi-reliable facility can be used for communication between a client and a server group as well as true peer-to-peer group communication. Resource location in a LAN is an important application domain. The term 'semi-reliable' refers to the fact that group membership changes go undetected. No attempt is made to assess the current membership of the group at any time--before, during, or after--the data transfer.

  9. Calculating system reliability with SRFYDO

    SciTech Connect

    Morzinski, Jerome; Anderson - Cook, Christine M; Klamann, Richard M

    2010-01-01

    SRFYDO is a process for estimating reliability of complex systems. Using information from all applicable sources, including full-system (flight) data, component test data, and expert (engineering) judgment, SRFYDO produces reliability estimates and predictions. It is appropriate for series systems with possibly several versions of the system which share some common components. It models reliability as a function of age and up to 2 other lifecycle (usage) covariates. Initial output from its Exploratory Data Analysis mode consists of plots and numerical summaries so that the user can check data entry and model assumptions, and help determine a final form for the system model. The System Reliability mode runs a complete reliability calculation using Bayesian methodology. This mode produces results that estimate reliability at the component, sub-system, and system level. The results include estimates of uncertainty, and can predict reliability at some not-too-distant time in the future. This paper presents an overview of the underlying statistical model for the analysis, discusses model assumptions, and demonstrates usage of SRFYDO.

  10. Multiple objective optimization in reliability demonstration test

    SciTech Connect

    Lu, Lu; Anderson-Cook, Christine Michaela; Li, Mingyang

    2016-10-01

    Reliability demonstration tests are usually performed in product design or validation processes to demonstrate whether a product meets specified requirements on reliability. For binomial demonstration tests, the zero-failure test has been most commonly used due to its simplicity and use of minimum sample size to achieve an acceptable consumer’s risk level. However, this test can often result in unacceptably high risk for producers as well as a low probability of passing the test even when the product has good reliability. This paper explicitly explores the interrelationship between multiple objectives that are commonly of interest when planning a demonstration test and proposes structured decision-making procedures using a Pareto front approach for selecting an optimal test plan based on simultaneously balancing multiple criteria. Different strategies are suggested for scenarios with different user priorities and graphical tools are developed to help quantify the trade-offs between choices and to facilitate informed decision making. As a result, potential impacts of some subjective user inputs on the final decision are studied to offer insights and useful guidance for general applications.

  11. Improve filtration for optimum equipment reliability

    SciTech Connect

    Cervera, S.M.

    1996-01-01

    The introduction 20 years ago of the American Petroleum Institute Standard API-614 as a purchase specification for lubrication, shaft sealing and control oil systems, had a considerable impact and did much to improve system reliability at that time. Today, however, these recommendations regarding filter rating and flushing cleanliness are outdated. Much research in the tribology field correlates clearance size particulate contamination with accelerated component wear, fatigue and performance degradation. Some of these studies demonstrate that by decreasing the population of clearance size particulate in lubrication oils, component life increases exponentially. Knowing the dynamic clearances of a piece of machinery makes it possible, using the ISO 4406 Cleanliness Code, to determine what cleanliness level will minimize contamination-related component wear/fatigue and thus help optimize machinery performance and reliability. Data obtained by the author through random sampling of rotating equipment lube and seal oil systems indicate that the API-614 standard, as it pertains to filtration and flushing, is insufficient to ensure that particulate contamination is maintained to within the levels necessary to achieve optimum equipment reliability and safety, without increasing operating cost. Adopting and practicing the guidelines presented should result in the following benefits: (1) the frequency of bearing, oil pump, mechanical seal, fluid coupling, gearbox and hydraulic control valve failures would be minimized; (2) the mean time between planned maintenance (MTBPM) would be increased. The result will be a substantial increase in safety and cost savings to the operator.

  12. Multiple objective optimization in reliability demonstration test

    DOE PAGES

    Lu, Lu; Anderson-Cook, Christine Michaela; Li, Mingyang

    2016-10-01

    Reliability demonstration tests are usually performed in product design or validation processes to demonstrate whether a product meets specified requirements on reliability. For binomial demonstration tests, the zero-failure test has been most commonly used due to its simplicity and use of minimum sample size to achieve an acceptable consumer’s risk level. However, this test can often result in unacceptably high risk for producers as well as a low probability of passing the test even when the product has good reliability. This paper explicitly explores the interrelationship between multiple objectives that are commonly of interest when planning a demonstration test andmore » proposes structured decision-making procedures using a Pareto front approach for selecting an optimal test plan based on simultaneously balancing multiple criteria. Different strategies are suggested for scenarios with different user priorities and graphical tools are developed to help quantify the trade-offs between choices and to facilitate informed decision making. As a result, potential impacts of some subjective user inputs on the final decision are studied to offer insights and useful guidance for general applications.« less

  13. Spontaneous neoplasia in four captive greater hedgehog tenrecs (Setifer setosus).

    PubMed

    Khoii, Mina K; Howerth, Elizabeth W; Burns, Roy B; Carmichael, K Paige; Gyimesi, Zoltan S

    2008-09-01

    Little information is available about diseases and pathology of species within the family Tenrecidae, including the greater hedgehog tenrec (Setifer setosus), a Madagascan insectivore. This report summarizes necropsy and histopathologic findings of neoplasia in four captive greater hedgehog tenrecs. Although only four animals are included in this report, neoplasia seems to be a common and significant source of morbidity and mortality in greater hedgehog tenrecs. Types of neoplasia identified include a thyroid follicular-solid carcinoma, two urinary bladder transitional cell carcinomas, uterine endometrial polyps, and multicentric B-cell lymphoma. Due to small sample size, no etiology could be determined, but genetics, viral infection, pesticide treatment, nutrition, or other environmental factors might contribute to the development of neoplasia in this species. This is the first report of neoplasia in greater hedgehog tenrecs.

  14. (Centralized Reliability Data Organization (CRDO))

    SciTech Connect

    Haire, M J

    1987-04-21

    One of the primary goals of the Centralized Reliability Data Organization (CREDO) is to be an international focal point for the collection, analysis, and dissemination of liquid metal reactor (LMR) component reliability, availability, and maintainability (RAM) data. During FY-1985, the Department of Energy (DOE) entered into a Specific Memorandum of Agreement (SMA) with Japan's Power Reactor and Nuclear Fuel Development Corporation (PNC) regarding cooperative data exchange efforts. This agreement was CREDO's first step toward internationalization and represented an initial realization of the previously mentioned goal. DOE's interest in further internationalization of the CREDO system was the primary motivation for the traveler's attendance at the Reliability '87 conference.

  15. Aerospace reliability applied to biomedicine.

    NASA Technical Reports Server (NTRS)

    Lalli, V. R.; Vargo, D. J.

    1972-01-01

    An analysis is presented that indicates that the reliability and quality assurance methodology selected by NASA to minimize failures in aerospace equipment can be applied directly to biomedical devices to improve hospital equipment reliability. The Space Electric Rocket Test project is used as an example of NASA application of reliability and quality assurance (R&QA) methods. By analogy a comparison is made to show how these same methods can be used in the development of transducers, instrumentation, and complex systems for use in medicine.

  16. Evaluation of reliability modeling tools for advanced fault tolerant systems

    NASA Technical Reports Server (NTRS)

    Baker, Robert; Scheper, Charlotte

    1986-01-01

    The Computer Aided Reliability Estimation (CARE III) and Automated Reliability Interactice Estimation System (ARIES 82) reliability tools for application to advanced fault tolerance aerospace systems were evaluated. To determine reliability modeling requirements, the evaluation focused on the Draper Laboratories' Advanced Information Processing System (AIPS) architecture as an example architecture for fault tolerance aerospace systems. Advantages and limitations were identified for each reliability evaluation tool. The CARE III program was designed primarily for analyzing ultrareliable flight control systems. The ARIES 82 program's primary use was to support university research and teaching. Both CARE III and ARIES 82 were not suited for determining the reliability of complex nodal networks of the type used to interconnect processing sites in the AIPS architecture. It was concluded that ARIES was not suitable for modeling advanced fault tolerant systems. It was further concluded that subject to some limitations (the difficulty in modeling systems with unpowered spare modules, systems where equipment maintenance must be considered, systems where failure depends on the sequence in which faults occurred, and systems where multiple faults greater than a double near coincident faults must be considered), CARE III is best suited for evaluating the reliability of advanced tolerant systems for air transport.

  17. Post-irradiation angiosarcoma of the greater omentum.

    PubMed

    Westenberg, A H; Wiggers, T; Henzen-Logmans, S C; Verweij, J; Meerwaldt, J A; van Geel, A N

    1989-04-01

    A case of angiosarcoma of the greater omentum is reported. This angiosarcoma developed 8 years after irradiation for cervical carcinoma and presented with an intra-abdominal hemorrhage. We describe her clinical course, treatment and follow-up. Although several other locations of irradiation-induced sarcomas have been published, this is the first report in literature of a postirradiation angiosarcoma in the greater omentum.

  18. High-Reliability Health Care: Getting There from Here

    PubMed Central

    Chassin, Mark R; Loeb, Jerod M

    2013-01-01

    Context Despite serious and widespread efforts to improve the quality of health care, many patients still suffer preventable harm every day. Hospitals find improvement difficult to sustain, and they suffer “project fatigue” because so many problems need attention. No hospitals or health systems have achieved consistent excellence throughout their institutions. High-reliability science is the study of organizations in industries like commercial aviation and nuclear power that operate under hazardous conditions while maintaining safety levels that are far better than those of health care. Adapting and applying the lessons of this science to health care offer the promise of enabling hospitals to reach levels of quality and safety that are comparable to those of the best high-reliability organizations. Methods We combined the Joint Commission's knowledge of health care organizations with knowledge from the published literature and from experts in high-reliability industries and leading safety scholars outside health care. We developed a conceptual and practical framework for assessing hospitals’ readiness for and progress toward high reliability. By iterative testing with hospital leaders, we refined the framework and, for each of its fourteen components, defined stages of maturity through which we believe hospitals must pass to reach high reliability. Findings We discovered that the ways that high-reliability organizations generate and maintain high levels of safety cannot be directly applied to today's hospitals. We defined a series of incremental changes that hospitals should undertake to progress toward high reliability. These changes involve the leadership's commitment to achieving zero patient harm, a fully functional culture of safety throughout the organization, and the widespread deployment of highly effective process improvement tools. Conclusions Hospitals can make substantial progress toward high reliability by undertaking several specific

  19. Effect of Tax Ratification Elections on Student Achievement

    ERIC Educational Resources Information Center

    Groppel, Lance

    2013-01-01

    This dissertation examines the impact a Tax Ratification Election has on student achievement in Texas. Texas schools continue to struggle with shrinking budgets and increasing standards of student achievement (Equity Center, 2011). This study will provide greater insight into whether school districts that have completed a TRE have created a…

  20. Achieving closure at Fernald

    SciTech Connect

    Bradburne, John; Patton, Tisha C.

    2001-02-25

    When Fluor Fernald took over the management of the Fernald Environmental Management Project in 1992, the estimated closure date of the site was more than 25 years into the future. Fluor Fernald, in conjunction with DOE-Fernald, introduced the Accelerated Cleanup Plan, which was designed to substantially shorten that schedule and save taxpayers more than $3 billion. The management of Fluor Fernald believes there are three fundamental concerns that must be addressed by any contractor hoping to achieve closure of a site within the DOE complex. They are relationship management, resource management and contract management. Relationship management refers to the interaction between the site and local residents, regulators, union leadership, the workforce at large, the media, and any other interested stakeholder groups. Resource management is of course related to the effective administration of the site knowledge base and the skills of the workforce, the attraction and retention of qualified a nd competent technical personnel, and the best recognition and use of appropriate new technologies. Perhaps most importantly, resource management must also include a plan for survival in a flat-funding environment. Lastly, creative and disciplined contract management will be essential to effecting the closure of any DOE site. Fluor Fernald, together with DOE-Fernald, is breaking new ground in the closure arena, and ''business as usual'' has become a thing of the past. How Fluor Fernald has managed its work at the site over the last eight years, and how it will manage the new site closure contract in the future, will be an integral part of achieving successful closure at Fernald.

  1. Reliability science and patient safety.

    PubMed

    Luria, Joseph W; Muething, Stephen E; Schoettker, Pamela J; Kotagal, Uma R

    2006-12-01

    Reliability is failure-free operation over time--the measurable capability of a process, procedure, or service to perform its intended function. Reliability science has the potential to help health care organizations reduce defects in care, increase the consistency with which care is delivered, and improve patient outcomes. Based on its principles, the Institute for Health care Improvement has developed a three-step model to prevent failures, mitigate the failures that occur, and redesign systems to reduce failures. Lessons may also be learned from complex organizations that have already adopted the principles of reliability science and operate with high rates of reliability. They share a preoccupation with failure, reluctance to simplify interpretations, sensitivity to operations, commitment to resilience, and underspecification of structures.

  2. How Reliable Is Laboratory Testing?

    MedlinePlus

    ... page: Was this page helpful? Overview | Key Concepts | Quality Control | Role of Testing | Conclusion | Sources What are the ... but is constantly monitored for reliability through comprehensive quality control and quality assurance procedures. Therefore, when your blood ...

  3. Accelerator Availability and Reliability Issues

    SciTech Connect

    Steve Suhring

    2003-05-01

    Maintaining reliable machine operations for existing machines as well as planning for future machines' operability present significant challenges to those responsible for system performance and improvement. Changes to machine requirements and beam specifications often reduce overall machine availability in an effort to meet user needs. Accelerator reliability issues from around the world will be presented, followed by a discussion of the major factors influencing machine availability.

  4. Reliability Validation and Improvement Framework

    DTIC Science & Technology

    2012-11-01

    discover and remove bugs using various test cover- age metrics to determine test sufficiency. Failure-probability density function based on code met- rics ...Coverage Metrics Traditional reliability engineering has focused on fault density and reliability growth as key met- rics . These are statistical...abs_all.jsp?arnumber=781027 [Kwiatkowska 2010] Kwiatkowska, M., Norman, G., & Parker , D. “Advances and Challenges of Probabilistic Model Checking

  5. Home media and children's achievement and behavior.

    PubMed

    Hofferth, Sandra L

    2010-01-01

    This study provides a national picture of the time American 6- to 12-year-olds spent playing video games, using the computer, and watching TV at home in 1997 and 2003, and the association of early use with their achievement and behavior as adolescents. Girls benefited from computer use more than boys, and Black children benefited more than White children. Greater computer use in middle childhood was associated with increased achievement for White and Black girls, and for Black but not White boys. Increased video game play was associated with an improved ability to solve applied problems for Black girls but lower verbal achievement for all girls. For boys, increased video game play was linked to increased aggressive behavior problems.

  6. Greater performance impairment of black runners than white runners when running in hypoxia.

    PubMed

    Santos-Concejero, J; Tucker, R; Myburgh, K H; Essen-Gustavsson, B; Kohn, T A

    2014-09-01

    This study aimed to compare the response of performance-matched black and white runners during maximal and sub-maximal running in normoxic and hypoxic conditions. 14 well-trained runners (8 black, 6 white) performed 2 incremental maximal exercise tests and 2 fatigue resistance tests at 21% O2 (normoxia) or 14% O2 (hypoxia). Respiratory parameters, heart rate (HR), lactate concentration ([La(-)]) as well as arterial saturation (SpO2) were measured. Enzyme activities and myosin heavy chain content (MHC) were also measured. White runners reached a significantly greater peak treadmill speed and a higher HRmax than black runners in hypoxia (p<0.05). Additionally, White runners achieved a greater time to fatigue than black runners (p<0.05), with black runners displaying a greater decline in performance in hypoxia compared to normoxia (20.3% vs. 13.4%, black vs. white, respectively). However, black runners presented lower [La(-)] and higher SpO2 than white runners in hypoxia (p<0.05). Black runners had a higher proportion of MHC IIa and higher lactate dehydrogenase activity (p<0.05). The greater performance impairment observed in black runners in hypoxia suggests a greater performance sensitivity to this condition, despite the maintenance of physiological variables such as SpO2 and [La (-) ] within a smaller range than white runners.

  7. Nesting success and resource selection of greater sage grouse in South Dakota

    USGS Publications Warehouse

    Kaczor, Nicholas W.; Jensen, Kent C.; Klaver, Robert W.; Rumble, Mark A.; Herman-Brunson, Katie M.; Swanson, Christopher C.; Sandercock, Brett K.; Martin, Kathy; Segelbacher, Gernot

    2011-01-01

    Declines of Greater Sage-Grouse (Centrocercus urophasianus) in South Dakota are a concern because further population declines may lead to isolation from populations in Wyoming and Montana. Furthermore, little information exists about reproductive ecology and resource selection of sage grouse on the eastern edge of their distribution. We investigated Greater Sage-Grouse nesting success and resource selection in South Dakota during 2006-2007. Radiomarked females were tracked to estimate nesting rates, nest success, and habitat resources selected for nesting. Nest initiation was 98.0%, with a maximum likelihood estimate of nest success of 45.6 ± 5.3%. Females selected nest sites that had greater sagebrush canopy cover and visual obstruction of the nest bowl compared to random sites. Nest survival models indicated that taller grass surrounding nests increased nest survival. Tall grass may supplement the low sagebrush cover in this area in providing suitable nest sites for Greater Sage-Grouse. Land managers on the eastern edge of Greater Sage-Grouse range could focus on increasing sagebrush density while maintaining tall grass by developing range management practices that accomplish this goal. To achieve nest survival rates similar to other populations, predictions from our models suggest 26 cm grass height would result in approximately 50% nest survival. Optimal conditions could be accomplished by adjusting livestock grazing systems and stocking rates.

  8. MEMS reliability: coming of age

    NASA Astrophysics Data System (ADS)

    Douglass, Michael R.

    2008-02-01

    In today's high-volume semiconductor world, one could easily take reliability for granted. As the MOEMS/MEMS industry continues to establish itself as a viable alternative to conventional manufacturing in the macro world, reliability can be of high concern. Currently, there are several emerging market opportunities in which MOEMS/MEMS is gaining a foothold. Markets such as mobile media, consumer electronics, biomedical devices, and homeland security are all showing great interest in microfabricated products. At the same time, these markets are among the most demanding when it comes to reliability assurance. To be successful, each company developing a MOEMS/MEMS device must consider reliability on an equal footing with cost, performance and manufacturability. What can this maturing industry learn from the successful development of DLP technology, air bag accelerometers and inkjet printheads? This paper discusses some basic reliability principles which any MOEMS/MEMS device development must use. Examples from the commercially successful and highly reliable Digital Micromirror Device complement the discussion.

  9. Increasing Score Reliability with Item-Pattern Scoring: An Empirical Study in Several Score Metrics.

    ERIC Educational Resources Information Center

    Yen, Wendy M.; Candell, Gregory L.

    Reliabilities are compared for two types of test score data: number correct, and item response patterns. Item-pattern scoring using three-parameter item response theory takes into account how many and which items a student answers correctly. This procedure theoretically results in greater reliability than does number-correct scoring. Empirical…

  10. Achievement Goals and Achievement Emotions: A Meta-Analysis

    ERIC Educational Resources Information Center

    Huang, Chiungjung

    2011-01-01

    This meta-analysis synthesized 93 independent samples (N = 30,003) in 77 studies that reported in 78 articles examining correlations between achievement goals and achievement emotions. Achievement goals were meaningfully associated with different achievement emotions. The correlations of mastery and mastery approach goals with positive achievement…

  11. Teaching and Assessing Low-Achieving Students with Disabilities: A Guide to Alternate Assessments Based on Modified Achievement Standards

    ERIC Educational Resources Information Center

    Perie, Marianne, Ed.

    2010-01-01

    For lower-achieving students with disabilities, effective and appropriate alternate assessment based on modified achievement standards (AA-MAS) can open the door to greater expectations and opportunities. State policymakers have the option of providing certain students who have disabilities with AA-MAS aligned with grade-level content--and now…

  12. Predicting Greater Prairie-Chicken Lek Site Suitability to Inform Conservation Actions

    PubMed Central

    Hovick, Torre J.; Dahlgren, David K.; Papeş, Monica; Elmore, R. Dwayne; Pitman, James C.

    2015-01-01

    The demands of a growing human population dictates that expansion of energy infrastructure, roads, and other development frequently takes place in native rangelands. Particularly, transmission lines and roads commonly divide rural landscapes and increase fragmentation. This has direct and indirect consequences on native wildlife that can be mitigated through thoughtful planning and proactive approaches to identifying areas of high conservation priority. We used nine years (2003–2011) of Greater Prairie-Chicken (Tympanuchus cupido) lek locations totaling 870 unique leks sites in Kansas and seven geographic information system (GIS) layers describing land cover, topography, and anthropogenic structures to model habitat suitability across the state. The models obtained had low omission rates (<0.18) and high area under the curve scores (AUC >0.81), indicating high model performance and reliability of predicted habitat suitability for Greater Prairie-Chickens. We found that elevation was the most influential in predicting lek locations, contributing three times more predictive power than any other variable. However, models were improved by the addition of land cover and anthropogenic features (transmission lines, roads, and oil and gas structures). Overall, our analysis provides a hierarchal understanding of Greater Prairie-Chicken habitat suitability that is broadly based on geomorphological features followed by land cover suitability. We found that when land features and vegetation cover are suitable for Greater Prairie-Chickens, fragmentation by anthropogenic sources such as roadways and transmission lines are a concern. Therefore, it is our recommendation that future human development in Kansas avoid areas that our models identified as highly suitable for Greater Prairie-Chickens and focus development on land cover types that are of lower conservation concern. PMID:26317349

  13. Home Media and Children’s Achievement and Behavior

    PubMed Central

    Hofferth, Sandra L.

    2010-01-01

    This study provides a national picture of the time American 6–12 year olds spent playing video games, using the computer, and watching television at home in 1997 and 2003 and the association of early use with their achievement and behavior as adolescents. Girls benefited from computers more than boys and Black children’s achievement benefited more from greater computer use than did that of White children. Greater computer use in middle childhood was associated with increased achievement for White and Black girls and Black boys, but not White boys. Greater computer play was also associated with a lower risk of becoming socially isolated among girls. Computer use does not crowd out positive learning-related activities, whereas video game playing does. Consequently, increased video game play had both positive and negative associations with the achievement of girls but not boys. For boys, increased video game play was linked to increased aggressive behavior problems. PMID:20840243

  14. Reliability Impacts in Life Support Architecture and Technology Selection

    NASA Technical Reports Server (NTRS)

    Lange, Kevin E.; Anderson, Molly S.

    2011-01-01

    Equivalent System Mass (ESM) and reliability estimates were performed for different life support architectures based primarily on International Space Station (ISS) technologies. The analysis was applied to a hypothetical 1-year deep-space mission. High-level fault trees were initially developed relating loss of life support functionality to the Loss of Crew (LOC) top event. System reliability was then expressed as the complement (nonoccurrence) this event and was increased through the addition of redundancy and spares, which added to the ESM. The reliability analysis assumed constant failure rates and used current projected values of the Mean Time Between Failures (MTBF) from an ISS database where available. Results were obtained showing the dependence of ESM on system reliability for each architecture. Although the analysis employed numerous simplifications and many of the input parameters are considered to have high uncertainty, the results strongly suggest that achieving necessary reliabilities for deep-space missions will add substantially to the life support system mass. As a point of reference, the reliability for a single-string architecture using the most regenerative combination of ISS technologies without unscheduled replacement spares was estimated to be less than 1%. The results also demonstrate how adding technologies in a serial manner to increase system closure forces the reliability of other life support technologies to increase in order to meet the system reliability requirement. This increase in reliability results in increased mass for multiple technologies through the need for additional spares. Alternative parallel architecture approaches and approaches with the potential to do more with less are discussed. The tall poles in life support ESM are also reexamined in light of estimated reliability impacts.

  15. Inter-Observer Reliability of DSM-5 Substance Use Disorders*

    PubMed Central

    Denis, Cécile M.; Gelernter, Joel; Hart, Amy B.; Kranzler, Henry R.

    2015-01-01

    Aims Although studies have examined the impact of changes made in DSM-5 on the estimated prevalence of substance use disorder (SUD) diagnoses, there is limited evidence of the reliability of DSM-5 SUDs. We evaluated the inter-observer reliability of four DSM-5 SUDs in a sample in which we had previously evaluated the reliability of DSM-IV diagnoses, allowing us to compare the two systems. Methods Two different interviewers each assessed 173 subjects over a 2-week period using the Semi-Structured Assessment for Drug Dependence and Alcoholism (SSADDA). Using the percent agreement and kappa (κ) coefficient, we examined the reliability of DSM-5 lifetime alcohol, opioid, cocaine, and cannabis use disorders, which we compared to that of SSADDA-derived DSM-IV SUD diagnoses. We also assessed the effect of additional lifetime SUD and lifetime mood or anxiety disorder diagnoses on the reliability of the DSM-5 SUD diagnoses. Results Reliability was good to excellent for the four disorders, with κ values ranging from 0.65 to 0.94. Agreement was consistently lower for SUDs of mild severity than for moderate or severe disorders. DSM-5 SUD diagnoses showed greater reliability than DSM-IV diagnoses of abuse or dependence or dependence only. Co-occurring SUD and lifetime mood or anxiety disorders exerted a modest effect on the reliability of the DSM-5 SUD diagnoses. Conclusions For alcohol, opioid, cocaine and cannabis use disorders, DSM-5 criteria and diagnoses are at least as reliable as those of DSM-IV. PMID:26048641

  16. Human reliability assessment: tools for law enforcement

    NASA Astrophysics Data System (ADS)

    Ryan, Thomas G.; Overlin, Trudy K.

    1997-01-01

    This paper suggests ways in which human reliability analysis (HRA) can assist the United State Justice System, and more specifically law enforcement, in enhancing the reliability of the process from evidence gathering through adjudication. HRA is an analytic process identifying, describing, quantifying, and interpreting the state of human performance, and developing and recommending enhancements based on the results of individual HRA. It also draws on lessons learned from compilations of several HRA. Given the high legal standards the Justice System is bound to, human errors that might appear to be trivial in other venues can make the difference between a successful and unsuccessful prosecution. HRA has made a major contribution to the efficiency, favorable cost-benefit ratio, and overall success of many enterprises where humans interface with sophisticated technologies, such as the military, ground transportation, chemical and oil production, nuclear power generation, commercial aviation and space flight. Each of these enterprises presents similar challenges to the humans responsible for executing action and action sequences, especially where problem solving and decision making are concerned. Nowhere are humans confronted, to a greater degree, with problem solving and decision making than are the diverse individuals and teams responsible for arrest and adjudication of criminal proceedings. This paper concludes that because of the parallels between the aforementioned technologies and the adjudication process, especially crime scene evidence gathering, there is reason to believe that the HRA technology, developed and enhanced in other applications, can be transferred to the Justice System with minimal cost and with significant payoff.

  17. Crystalline-silicon reliability lessons for thin-film modules

    NASA Technical Reports Server (NTRS)

    Ross, R. G., Jr.

    1985-01-01

    The reliability of crystalline silicon modules has been brought to a high level with lifetimes approaching 20 years, and excellent industry credibility and user satisfaction. The transition from crystalline modules to thin film modules is comparable to the transition from discrete transistors to integrated circuits. New cell materials and monolithic structures will require new device processing techniques, but the package function and design will evolve to a lesser extent. Although there will be new encapsulants optimized to take advantage of the mechanical flexibility and low temperature processing features of thin films, the reliability and life degradation stresses and mechanisms will remain mostly unchanged. Key reliability technologies in common between crystalline and thin film modules include hot spot heating, galvanic and electrochemical corrosion, hail impact stresses, glass breakage, mechanical fatigue, photothermal degradation of encapsulants, operating temperature, moisture sorption, circuit design strategies, product safety issues, and the process required to achieve a reliable product from a laboratory prototype.

  18. Reliability model of a monopropellant auxiliary propulsion system

    NASA Technical Reports Server (NTRS)

    Greenberg, J. S.

    1971-01-01

    A mathematical model and associated computer code has been developed which computes the reliability of a monopropellant blowdown hydrazine spacecraft auxiliary propulsion system as a function of time. The propulsion system is used to adjust or modify the spacecraft orbit over an extended period of time. The multiple orbit corrections are the multiple objectives which the auxiliary propulsion system is designed to achieve. Thus the reliability model computes the probability of successfully accomplishing each of the desired orbit corrections. To accomplish this, the reliability model interfaces with a computer code that models the performance of a blowdown (unregulated) monopropellant auxiliary propulsion system. The computer code acts as a performance model and as such gives an accurate time history of the system operating parameters. The basic timing and status information is passed on to and utilized by the reliability model which establishes the probability of successfully accomplishing the orbit corrections.

  19. Working Group summary reports from the Advanced Photon Source reliability workshop

    SciTech Connect

    Not Available

    1992-05-01

    A workshop was held at APS to address reliability goals for accelerator systems. Seventy-one individuals participated in the workshop, including 30 from other institutions. The goals of the workshop were to: (1) Give attendees an introduction to the basic concepts of reliability analysis. (2) Exchange information on operating experience at existing accelerator facilities and strategies for achieving reliability at facilities under design or in construction. (3) Discuss reliability goals for APS and the means of their achievement. This report contains the working group summary report an APS`s following systems: RF Systems; Power Supplies; Magnet Systems; Interlock and Diagnostics; and Vacuum Systems.

  20. Working Group summary reports from the Advanced Photon Source reliability workshop

    SciTech Connect

    Not Available

    1992-05-01

    A workshop was held at APS to address reliability goals for accelerator systems. Seventy-one individuals participated in the workshop, including 30 from other institutions. The goals of the workshop were to: (1) Give attendees an introduction to the basic concepts of reliability analysis. (2) Exchange information on operating experience at existing accelerator facilities and strategies for achieving reliability at facilities under design or in construction. (3) Discuss reliability goals for APS and the means of their achievement. This report contains the working group summary report an APS's following systems: RF Systems; Power Supplies; Magnet Systems; Interlock and Diagnostics; and Vacuum Systems.

  1. WEST ELEVATION OF USAIR MAINTENANCE HANGAR AT GREATER BUFFALO INTERNATIONAL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    WEST ELEVATION OF USAIR MAINTENANCE HANGAR AT GREATER BUFFALO INTERNATIONAL AIRPORT. A BOEING 737-200 HAS BEEN TOWED IN FOR AN OVERNIGHT (BALANCE) CHECK. THE TAIL DOCK STANDS ARE IN POSITION AT THE REAR OF THE AIRCRAFT TO FACILITATE INSPECTION. MAINTENANCE CREWS PERFORM NIGHTLY SERVICE ON UP TO 6 AIRCRAFT. THE NORMAL SEQUENCE OF 12 ROUTINE CHECKS COVERS SEVEN BASIC AREAS: INTERIOR, EXTERIOR, WINGS, LANDING GEAR, TAIL, AUXILIARY POWER UNIT (APU), AND ENGINES. THE WORK FORCE CONSISTS OF 5 INSPECTORS, 3 LEAD MECHANICS, AND 24 MECHANICS; NIGHTLY SCHEDULES ARE COORDINATED BY A PLANNER. - Greater Buffalo International Airport, Maintenance Hangar, Buffalo, Erie County, NY

  2. 18 CFR 39.11 - Reliability reports.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Reliability reports. 39... RELIABILITY ORGANIZATION; AND PROCEDURES FOR THE ESTABLISHMENT, APPROVAL, AND ENFORCEMENT OF ELECTRIC RELIABILITY STANDARDS § 39.11 Reliability reports. (a) The Electric Reliability Organization shall...

  3. Recent advances in computational structural reliability analysis methods

    NASA Technical Reports Server (NTRS)

    Thacker, Ben H.; Wu, Y.-T.; Millwater, Harry R.; Torng, Tony Y.; Riha, David S.

    1993-01-01

    The goal of structural reliability analysis is to determine the probability that the structure will adequately perform its intended function when operating under the given environmental conditions. Thus, the notion of reliability admits the possibility of failure. Given the fact that many different modes of failure are usually possible, achievement of this goal is a formidable task, especially for large, complex structural systems. The traditional (deterministic) design methodology attempts to assure reliability by the application of safety factors and conservative assumptions. However, the safety factor approach lacks a quantitative basis in that the level of reliability is never known and usually results in overly conservative designs because of compounding conservatisms. Furthermore, problem parameters that control the reliability are not identified, nor their importance evaluated. A summary of recent advances in computational structural reliability assessment is presented. A significant level of activity in the research and development community was seen recently, much of which was directed towards the prediction of failure probabilities for single mode failures. The focus is to present some early results and demonstrations of advanced reliability methods applied to structural system problems. This includes structures that can fail as a result of multiple component failures (e.g., a redundant truss), or structural components that may fail due to multiple interacting failure modes (e.g., excessive deflection, resonate vibration, or creep rupture). From these results, some observations and recommendations are made with regard to future research needs.

  4. Process Stationarity and Reliability of Trunk Postural Stability

    PubMed Central

    Lee, HyunWook; Granata, Kevin P.

    2009-01-01

    Background Empirical assessments of torso stability can be estimated from postural variability and nonlinear analyses of seated balance tasks. However, processing methods require sufficient signal duration and test-retest experiments require the assessment must be reliable. Our goal was to characterize the reliability and establish the trial duration for torso stability assessment. Methods Kinetic and kinematic data were recorded while subjects maintained a seated posture on a wobbly seat pan. Stability was evaluated from dynamic variability and nonlinear stability analyses. Process stationarity of the measured signals characterized the minimum necessary trial duration. Intra-class correlations measured within-session and between-session reliability. Findings Trial duration necessary to achieve process stationarity was 30.2 seconds. Shorter time to stationarity was observed with measures that included multi-dimensional movement behavior. Summary statistics of movement variability demonstrated moderate intra-session reliability, ICC = 0.64 (range 0.38 – 0.87). Inter-session reliability for movement variance was moderate, ICC = 0.42 (range 0.22 – 0.64). Nonlinear stability measures typically performed better than estimates of variability with inter-session reliability as high as ICC = 0.83. Process stationarity and reliability were improved in more difficult balance conditions. Interpretation To adequately capture torso dynamics during the stability assessment the trial duration should be at least 30 seconds. Moderate to excellent test-retest reliability can be achieved in intra-session analyses, but more repeated measurements are required for inter-session comparisons. Stability diffusion exponents, HS, and the Lyapunov exponents provide excellent measures for intra-session analyses, while HS provides excellent inter-session comparisons of torso stability. PMID:18304711

  5. RXTE All-Sky Slew Survey. Catalog of X-Ray Sources at B Greater Than 10 deg

    NASA Technical Reports Server (NTRS)

    Revnivtsev, M.; Sazonov, S.; Jahoda, K.; Gilfanov, M.

    2004-01-01

    We report results of a serendipitous hard X-ray (3-20 keV), nearly all-sky (absolute value of b greater than l0 deg.) survey based on RXTE/PCA observations performed during satellite reorientations in 1996-2002. The survey is 80% (90%) complete to a 4(sigma) limiting flux of approx. = 1.8 (2.5) x 10(exp -l1) erg/s sq cm in the 3-20 keV band. The achieved sensitivity in the 3-8 keV and 8-20 keV subbands is similar to and an order of magnitude higher than that of the previously record HEAO-1 A1 and HEAO-1 A4 all-sky surveys, respectively. A combined 7 x 10(exp 3) sq. deg area of the sky is sampled to flux levels below l0(exp -11) erg/ s sq cm (3-20 keV). In total 294 sources are detected and localized to better than 1 deg. 236 (80%) of these can be confidently associated with a known astrophysical object; another 22 likely result from the superposition of 2 or 3 closely located known sources. 35 detected sources remain unidentified, although for 12 of these we report a likely soft X-ray counterpart from the ROSAT all-sky survey bright source catalog. Of the reliably identified sources, 63 have local origin (Milky Way, LMC or SMC), 64 are clusters of galaxies and 100 are active galactic nuclei (AGN). The fact that the unidentified X-ray sources have hard spectra suggests that the majority of them are AGN, including highly obscured ones (N(sub H) greater than l0(exp 23)/sq cm). For the first time we present a log N-log S diagram for extragalactic sources above 4 x l0(exp -12) erg/ s sq cm at 8-20 keV. Key words. cosmo1ogy:observations - diffuse radiation - X-rays general

  6. The Educational Afterlife of Greater Britain, 1903-1914

    ERIC Educational Resources Information Center

    Gardner, Philip

    2012-01-01

    Following its late nineteenth-century emergence as an important element within federalist thinking across the British Empire, the idea of Greater Britain lost much of its political force in the years following the Boer War. The concept however continued to retain considerable residual currency in other fields of Imperial debate, including those…

  7. College Students with ADHD at Greater Risk for Sleep Disorders

    ERIC Educational Resources Information Center

    Gaultney, Jane F.

    2014-01-01

    The pediatric literature indicates that children with ADHD are at greater risk for sleep problems, daytime sleepiness, and some sleep disorders than children with no diagnosed disability. It has not been determined whether this pattern holds true among emerging adults, and whether comorbid sleep disorders with ADHD predict GPA. The present study…

  8. Report Urges Greater Coordination of European Doctoral Education

    ERIC Educational Resources Information Center

    Labi, Aisha

    2007-01-01

    A new report assessing the state of doctoral education in Europe says that, even as 47 European nations enter the final phase of harmonizing their degree programs, Ph.D.-level education across Europe suffers from a lack of coordination and cooperation. "There is an urgent need for greater consultation and coordination at the regional,…

  9. External Scan 2000: Environmental Scan of the Greater Sacramento Area.

    ERIC Educational Resources Information Center

    Beachler, Judith

    This document provides a summary of the social, economic, and political changes at state and national levels that affect the Los Rios Community College District (LRCCD) in California. LRCCD consists of American River College (ARC), Cosumnes River College (CRC), and Sacramento City College (SCC). Demographic trends show that Greater Sacramento is…

  10. Reliability model for planetary gear

    NASA Technical Reports Server (NTRS)

    Savage, M.; Paridon, C. A.; Coy, J. J.

    1982-01-01

    A reliability model is presented for planetary gear trains in which the ring gear is fixed, the Sun gear is the input, and the planet arm is the output. The input and output shafts are coaxial and the input and output torques are assumed to be coaxial with these shafts. Thrust and side loading are neglected. This type of gear train is commonly used in main rotor transmissions for helicopters and in other applications which require high reductions in speed. The reliability model is based on the Weibull distribution of the individual reliabilities of the transmission components. The transmission's basic dynamic capacity is defined as the input torque which may be applied for one million input rotations of the Sun gear. Load and life are related by a power law. The load life exponent and basic dynamic capacity are developed as functions of the component capacities.

  11. Electronics reliability and measurement technology

    NASA Technical Reports Server (NTRS)

    Heyman, Joseph S. (Editor)

    1987-01-01

    A summary is presented of the Electronics Reliability and Measurement Technology Workshop. The meeting examined the U.S. electronics industry with particular focus on reliability and state-of-the-art technology. A general consensus of the approximately 75 attendees was that "the U.S. electronics industries are facing a crisis that may threaten their existence". The workshop had specific objectives to discuss mechanisms to improve areas such as reliability, yield, and performance while reducing failure rates, delivery times, and cost. The findings of the workshop addressed various aspects of the industry from wafers to parts to assemblies. Key problem areas that were singled out for attention are identified, and action items necessary to accomplish their resolution are recommended.

  12. A Review of Score Reliability: Contemporary Thinking on Reliability Issues

    ERIC Educational Resources Information Center

    Rosen, Gerald A.

    2004-01-01

    Bruce Thompson's edited volume begins with a basic principle, one might call it a basic truth, "reliability is a property that applies to scores, and not immutably across all conceivable uses everywhere of a given measure." (p. 3). The author claims that this principle is little known and-or little understood. While that is an arguable point, the…

  13. Designing magnetic systems for reliability

    SciTech Connect

    Heitzenroeder, P.J.

    1991-01-01

    Designing magnetic system is an iterative process in which the requirements are set, a design is developed, materials and manufacturing processes are defined, interrelationships with the various elements of the system are established, engineering analyses are performed, and fault modes and effects are studied. Reliability requires that all elements of the design process, from the seemingly most straightforward such as utilities connection design and implementation, to the most sophisticated such as advanced finite element analyses, receives a balanced and appropriate level of attention. D.B. Montgomery's study of magnet failures has shown that the predominance of magnet failures tend not to be in the most intensively engineered areas, but are associated with insulation, leads, ad unanticipated conditions. TFTR, JET, JT-60, and PBX are all major tokamaks which have suffered loss of reliability due to water leaks. Similarly the majority of causes of loss of magnet reliability at PPPL has not been in the sophisticated areas of the design but are due to difficulties associated with coolant connections, bus connections, and external structural connections. Looking towards the future, the major next-devices such as BPX and ITER are most costly and complex than any of their predecessors and are pressing the bounds of operating levels, materials, and fabrication. Emphasis on reliability is a must as the fusion program enters a phase where there are fewer, but very costly devices with the goal of reaching a reactor prototype stage in the next two or three decades. This paper reviews some of the magnet reliability issues which PPPL has faced over the years the lessons learned from them, and magnet design and fabrication practices which have been found to contribute to magnet reliability.

  14. 78 FR 58492 - Generator Verification Reliability Standards

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-24

    ... Energy Regulatory Commission 18 CFR Part 40 Generator Verification Reliability Standards AGENCY: Federal... approve the following Reliability Standards that were submitted to the Commission for approval by the North American Electric Reliability Corporation, the Commission-certified Electric...

  15. 76 FR 16277 - System Restoration Reliability Standards

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-23

    ... Energy Regulatory Commission 18 CFR Part 40 System Restoration Reliability Standards AGENCY: Federal... Act, the Commission approves three Emergency Operations and Preparedness (EOP) Reliability Standards... Resource'' submitted to the Commission for approval by the North American Electric Reliability...

  16. 18 CFR 39.5 - Reliability Standards.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... competition. (d) An approved Reliability Standard or modification to a Reliability Standard shall take effect... will not defer to the Electric Reliability Organization or a Regional Entity with respect to the...

  17. Photovoltaic power system reliability considerations

    NASA Technical Reports Server (NTRS)

    Lalli, V. R.

    1980-01-01

    An example of how modern engineering and safety techniques can be used to assure the reliable and safe operation of photovoltaic power systems is presented. This particular application is for a solar cell power system demonstration project designed to provide electric power requirements for remote villages. The techniques utilized involve a definition of the power system natural and operating environment, use of design criteria and analysis techniques, an awareness of potential problems via the inherent reliability and FMEA methods, and use of fail-safe and planned spare parts engineering philosophy.

  18. Metrological Reliability of Medical Devices

    NASA Astrophysics Data System (ADS)

    Costa Monteiro, E.; Leon, L. F.

    2015-02-01

    The prominent development of health technologies of the 20th century triggered demands for metrological reliability of physiological measurements comprising physical, chemical and biological quantities, essential to ensure accurate and comparable results of clinical measurements. In the present work, aspects concerning metrological reliability in premarket and postmarket assessments of medical devices are discussed, pointing out challenges to be overcome. In addition, considering the social relevance of the biomeasurements results, Biometrological Principles to be pursued by research and innovation aimed at biomedical applications are proposed, along with the analysis of their contributions to guarantee the innovative health technologies compliance with the main ethical pillars of Bioethics.

  19. Mechanically reliable scales and coatings

    SciTech Connect

    Tortorelli, P.F.; Alexander, K.B.

    1995-07-01

    As the first stage in examining the mechanical reliability of protective surface oxides, the behavior of alumina scales formed on iron-aluminum alloys during high-temperature cyclic oxidation was characterized in terms of damage and spallation tendencies. Scales were thermally grown on specimens of three iron-aluminum composition using a series of exposures to air at 1000{degrees}C. Gravimetric data and microscopy revealed substantially better integrity and adhesion of the scales grown on an alloy containing zirconium. The use of polished (rather than just ground) specimens resulted in scales that were more suitable for subsequent characterization of mechanical reliability.

  20. Reliability and Maintainability Issues for the Next Linear Collider

    SciTech Connect

    Wilson, Zane J.; Gold, Saul L.; Koontz, Ron F.; Lavine, Ted L.; /SLAC

    2011-08-26

    Large accelerators for high energy physics research traditionally have been designed using informal best design, engineering, and management practices to achieve acceptable levels of operational availability. However, the Next Linear Collider(NLC) project presents a particular challenge for operational availability due to the unprecedented size and complexity of the accelerator systems required to achieve the physics goals of high center-of-mass energy and high luminosity. Formal reliability and maintainability analysis, design, and implementation will be required to achieve acceptable operational availability for the high energy physics research program. This paper introduces some of the basic concepts of reliability analysis and applies them to the 2.6-cm microwave power system of the two 10-km-long, 250-GeV linacs that are currently proposed for the NLC design.

  1. Lifting Minority Achievement: Complex Answers. The Achievement Gap.

    ERIC Educational Resources Information Center

    Viadero, Debra; Johnston, Robert C.

    2000-01-01

    This fourth in a four-part series on why academic achievement gaps exist describes the Minority Achievement Committee scholars program at Shaker Heights High School in Cleveland, Ohio, a powerful antidote to the achievement gap between minority and white and Asian American students. It explains the need to break down stereotypes about academic…

  2. Achievement Motivation of Women: Effects of Achievement and Affiliation Arousal.

    ERIC Educational Resources Information Center

    Gama, Elizabeth Maria Pinheiro

    1985-01-01

    Assigned 139 Brazilian women to neutral, affiliation arousal, and achievement arousal conditions based on their levels of achievement (Ach) and affiliative (Aff) needs. Results of story analyses revealed that achievement arousal increased scores of high Ach subjects and that high Aff subjects obtained higher scores than low Aff subjects. (BL)

  3. Attitude Towards Physics and Additional Mathematics Achievement Towards Physics Achievement

    ERIC Educational Resources Information Center

    Veloo, Arsaythamby; Nor, Rahimah; Khalid, Rozalina

    2015-01-01

    The purpose of this research is to identify the difference in students' attitude towards Physics and Additional Mathematics achievement based on gender and relationship between attitudinal variables towards Physics and Additional Mathematics achievement with achievement in Physics. This research focused on six variables, which is attitude towards…

  4. The Impact of Reading Achievement on Overall Academic Achievement

    ERIC Educational Resources Information Center

    Churchwell, Dawn Earheart

    2009-01-01

    This study examined the relationship between reading achievement and achievement in other subject areas. The purpose of this study was to determine if there was a correlation between reading scores as measured by the Standardized Test for the Assessment of Reading (STAR) and academic achievement in language arts, math, science, and social studies…

  5. Reliability analysis framework for computer-assisted medical decision systems

    SciTech Connect

    Habas, Piotr A.; Zurada, Jacek M.; Elmaghraby, Adel S.; Tourassi, Georgia D.

    2007-02-15

    We present a technique that enhances computer-assisted decision (CAD) systems with the ability to assess the reliability of each individual decision they make. Reliability assessment is achieved by measuring the accuracy of a CAD system with known cases similar to the one in question. The proposed technique analyzes the feature space neighborhood of the query case to dynamically select an input-dependent set of known cases relevant to the query. This set is used to assess the local (query-specific) accuracy of the CAD system. The estimated local accuracy is utilized as a reliability measure of the CAD response to the query case. The underlying hypothesis of the study is that CAD decisions with higher reliability are more accurate. The above hypothesis was tested using a mammographic database of 1337 regions of interest (ROIs) with biopsy-proven ground truth (681 with masses, 656 with normal parenchyma). Three types of decision models, (i) a back-propagation neural network (BPNN), (ii) a generalized regression neural network (GRNN), and (iii) a support vector machine (SVM), were developed to detect masses based on eight morphological features automatically extracted from each ROI. The performance of all decision models was evaluated using the Receiver Operating Characteristic (ROC) analysis. The study showed that the proposed reliability measure is a strong predictor of the CAD system's case-specific accuracy. Specifically, the ROC area index for CAD predictions with high reliability was significantly better than for those with low reliability values. This result was consistent across all decision models investigated in the study. The proposed case-specific reliability analysis technique could be used to alert the CAD user when an opinion that is unlikely to be reliable is offered. The technique can be easily deployed in the clinical environment because it is applicable with a wide range of classifiers regardless of their structure and it requires neither additional

  6. High-reliability computing for the smarter planet

    SciTech Connect

    Quinn, Heather M; Graham, Paul; Manuzzato, Andrea; Dehon, Andre; Carter, Nicholas

    2010-01-01

    The geometric rate of improvement of transistor size and integrated circuit performance, known as Moore's Law, has been an engine of growth for our economy, enabling new products and services, creating new value and wealth, increasing safety, and removing menial tasks from our daily lives. Affordable, highly integrated components have enabled both life-saving technologies and rich entertainment applications. Anti-lock brakes, insulin monitors, and GPS-enabled emergency response systems save lives. Cell phones, internet appliances, virtual worlds, realistic video games, and mp3 players enrich our lives and connect us together. Over the past 40 years of silicon scaling, the increasing capabilities of inexpensive computation have transformed our society through automation and ubiquitous communications. In this paper, we will present the concept of the smarter planet, how reliability failures affect current systems, and methods that can be used to increase the reliable adoption of new automation in the future. We will illustrate these issues using a number of different electronic devices in a couple of different scenarios. Recently IBM has been presenting the idea of a 'smarter planet.' In smarter planet documents, IBM discusses increased computer automation of roadways, banking, healthcare, and infrastructure, as automation could create more efficient systems. A necessary component of the smarter planet concept is to ensure that these new systems have very high reliability. Even extremely rare reliability problems can easily escalate to problematic scenarios when implemented at very large scales. For life-critical systems, such as automobiles, infrastructure, medical implantables, and avionic systems, unmitigated failures could be dangerous. As more automation moves into these types of critical systems, reliability failures will need to be managed. As computer automation continues to increase in our society, the need for greater radiation reliability is necessary

  7. Estimating numbers of greater prairie-chickens using mark-resight techniques

    USGS Publications Warehouse

    Clifton, A.M.; Krementz, D.G.

    2006-01-01

    Current monitoring efforts for greater prairie-chicken (Tympanuchus cupido pinnatus) populations indicate that populations are declining across their range. Monitoring the population status of greater prairie-chickens is based on traditional lek surveys (TLS) that provide an index without considering detectability. Estimators, such as immigration-emigration joint maximum-likelihood estimator from a hypergeometric distribution (IEJHE), can account for detectability and provide reliable population estimates based on resightings. We evaluated the use of mark-resight methods using radiotelemetry to estimate population size and density of greater prairie-chickens on 2 sites at a tallgrass prairie in the Flint Hills of Kansas, USA. We used average distances traveled from lek of capture to estimate density. Population estimates and confidence intervals at the 2 sites were 54 (CI 50-59) on 52.9 km 2 and 87 (CI 82-94) on 73.6 km2. The TLS performed at the same sites resulted in population ranges of 7-34 and 36-63 and always produced a lower population index than the mark-resight population estimate with a larger range. Mark-resight simulations with varying male:female ratios of marks indicated that this ratio was important in designing a population study on prairie-chickens. Confidence intervals for estimates when no marks were placed on females at the 2 sites (CI 46-50, 76-84) did not overlap confidence intervals when 40% of marks were placed on females (CI 54-64, 91-109). Population estimates derived using this mark-resight technique were apparently more accurate than traditional methods and would be more effective in detecting changes in prairie-chicken populations. Our technique could improve prairie-chicken management by providing wildlife biologists and land managers with a tool to estimate the population size and trends of lekking bird species, such as greater prairie-chickens.

  8. Ultra precision and reliable bonding method

    NASA Technical Reports Server (NTRS)

    Gwo, Dz-Hung (Inventor)

    2001-01-01

    The bonding of two materials through hydroxide-catalyzed hydration/dehydration is achieved at room temperature by applying hydroxide ions to at least one of the two bonding surfaces and by placing the surfaces sufficiently close to each other to form a chemical bond between them. The surfaces may be placed sufficiently close to each other by simply placing one surface on top of the other. A silicate material may also be used as a filling material to help fill gaps between the surfaces caused by surface figure mismatches. A powder of a silica-based or silica-containing material may also be used as an additional filling material. The hydroxide-catalyzed bonding method forms bonds which are not only as precise and transparent as optical contact bonds, but also as strong and reliable as high-temperature frit bonds. The hydroxide-catalyzed bonding method is also simple and inexpensive.

  9. System statistical reliability model and analysis

    NASA Technical Reports Server (NTRS)

    Lekach, V. S.; Rood, H.

    1973-01-01

    A digital computer code was developed to simulate the time-dependent behavior of the 5-kwe reactor thermoelectric system. The code was used to determine lifetime sensitivity coefficients for a number of system design parameters, such as thermoelectric module efficiency and degradation rate, radiator absorptivity and emissivity, fuel element barrier defect constant, beginning-of-life reactivity, etc. A probability distribution (mean and standard deviation) was estimated for each of these design parameters. Then, error analysis was used to obtain a probability distribution for the system lifetime (mean = 7.7 years, standard deviation = 1.1 years). From this, the probability that the system will achieve the design goal of 5 years lifetime is 0.993. This value represents an estimate of the degradation reliability of the system.

  10. Reliability Analysis of Money Habitudes

    ERIC Educational Resources Information Center

    Delgadillo, Lucy M.; Bushman, Brittani S.

    2015-01-01

    Use of the Money Habitudes exercise has gained popularity among various financial professionals. This article reports on the reliability of this resource. A survey administered to young adults at a western state university was conducted, and each Habitude or "domain" was analyzed using Cronbach's alpha procedures. Results showed all six…

  11. Reliability and cost analysis methods

    NASA Technical Reports Server (NTRS)

    Suich, Ronald C.

    1991-01-01

    In the design phase of a system, how does a design engineer or manager choose between a subsystem with .990 reliability and a more costly subsystem with .995 reliability? When is the increased cost justified? High reliability is not necessarily an end in itself but may be desirable in order to reduce the expected cost due to subsystem failure. However, this may not be the wisest use of funds since the expected cost due to subsystem failure is not the only cost involved. The subsystem itself may be very costly. We should not consider either the cost of the subsystem or the expected cost due to subsystem failure separately but should minimize the total of the two costs, i.e., the total of the cost of the subsystem plus the expected cost due to subsystem failure. This final report discusses the Combined Analysis of Reliability, Redundancy, and Cost (CARRAC) methods which were developed under Grant Number NAG 3-1100 from the NASA Lewis Research Center. CARRAC methods and a CARRAC computer program employ five models which can be used to cover a wide range of problems. The models contain an option which can include repair of failed modules.

  12. Interactive Maximum Reliability Cluster Analysis.

    ERIC Educational Resources Information Center

    Mays, Robert

    1978-01-01

    A FORTRAN program for clustering variables using the alpha coefficient of reliability is described. For batch operation, a rule for stopping the agglomerative precedure is available. The conversational version of the program allows the user to intervene in the process in order to test the final solution for sensitivity to changes. (Author/JKS)

  13. The Reliability of College Grades

    ERIC Educational Resources Information Center

    Beatty, Adam S.; Walmsley, Philip T.; Sackett, Paul R.; Kuncel, Nathan R.; Koch, Amanda J.

    2015-01-01

    Little is known about the reliability of college grades relative to how prominently they are used in educational research, and the results to date tend to be based on small sample studies or are decades old. This study uses two large databases (N > 800,000) from over 200 educational institutions spanning 13 years and finds that both first-year…

  14. Becoming a high reliability organization.

    PubMed

    Christianson, Marlys K; Sutcliffe, Kathleen M; Miller, Melissa A; Iwashyna, Theodore J

    2011-01-01

    Aircraft carriers, electrical power grids, and wildland firefighting, though seemingly different, are exemplars of high reliability organizations (HROs)--organizations that have the potential for catastrophic failure yet engage in nearly error-free performance. HROs commit to safety at the highest level and adopt a special approach to its pursuit. High reliability organizing has been studied and discussed for some time in other industries and is receiving increasing attention in health care, particularly in high-risk settings like the intensive care unit (ICU). The essence of high reliability organizing is a set of principles that enable organizations to focus attention on emergent problems and to deploy the right set of resources to address those problems. HROs behave in ways that sometimes seem counterintuitive--they do not try to hide failures but rather celebrate them as windows into the health of the system, they seek out problems, they avoid focusing on just one aspect of work and are able to see how all the parts of work fit together, they expect unexpected events and develop the capability to manage them, and they defer decision making to local frontline experts who are empowered to solve problems. Given the complexity of patient care in the ICU, the potential for medical error, and the particular sensitivity of critically ill patients to harm, high reliability organizing principles hold promise for improving ICU patient care.

  15. Wind turbine reliability database update.

    SciTech Connect

    Peters, Valerie A.; Hill, Roger Ray; Stinebaugh, Jennifer A.; Veers, Paul S.

    2009-03-01

    This report documents the status of the Sandia National Laboratories' Wind Plant Reliability Database. Included in this report are updates on the form and contents of the Database, which stems from a fivestep process of data partnerships, data definition and transfer, data formatting and normalization, analysis, and reporting. Selected observations are also reported.

  16. Wanted: A Solid, Reliable PC

    ERIC Educational Resources Information Center

    Goldsborough, Reid

    2004-01-01

    This article discusses PC reliability, one of the most pressing issues regarding computers. Nearly a quarter century after the introduction of the first IBM PC and the outset of the personal computer revolution, PCs have largely become commodities, with little differentiating one brand from another in terms of capability and performance. Most of…

  17. The Humanities versus Interrater Reliability

    ERIC Educational Resources Information Center

    RiCharde, R. Stephen

    2008-01-01

    A persistent conflict between assessment professionals and faculty members in the humanities seems to focus inevitably on resistance to the concept of interrater reliability. While humanities faculty are often willing to engage in course-embedded assessment that uses some type of scoring rubric, when the demand for agreement in scoring is…

  18. Photovoltaic performance and reliability workshop

    SciTech Connect

    Kroposki, B

    1996-10-01

    This proceedings is the compilation of papers presented at the ninth PV Performance and Reliability Workshop held at the Sheraton Denver West Hotel on September 4--6, 1996. This years workshop included presentations from 25 speakers and had over 100 attendees. All of the presentations that were given are included in this proceedings. Topics of the papers included: defining service lifetime and developing models for PV module lifetime; examining and determining failure and degradation mechanisms in PV modules; combining IEEE/IEC/UL testing procedures; AC module performance and reliability testing; inverter reliability/qualification testing; standardization of utility interconnect requirements for PV systems; need activities to separate variables by testing individual components of PV systems (e.g. cells, modules, batteries, inverters,charge controllers) for individual reliability and then test them in actual system configurations; more results reported from field experience on modules, inverters, batteries, and charge controllers from field deployed PV systems; and system certification and standardized testing for stand-alone and grid-tied systems.

  19. Parallelized reliability estimation of reconfigurable computer networks

    NASA Technical Reports Server (NTRS)

    Nicol, David M.; Das, Subhendu; Palumbo, Dan

    1990-01-01

    A parallelized system, ASSURE, for computing the reliability of embedded avionics flight control systems which are able to reconfigure themselves in the event of failure is described. ASSURE accepts a grammar that describes a reliability semi-Markov state-space. From this it creates a parallel program that simultaneously generates and analyzes the state-space, placing upper and lower bounds on the probability of system failure. ASSURE is implemented on a 32-node Intel iPSC/860, and has achieved high processor efficiencies on real problems. Through a combination of improved algorithms, exploitation of parallelism, and use of an advanced microprocessor architecture, ASSURE has reduced the execution time on substantial problems by a factor of one thousand over previous workstation implementations. Furthermore, ASSURE's parallel execution rate on the iPSC/860 is an order of magnitude faster than its serial execution rate on a Cray-2 supercomputer. While dynamic load balancing is necessary for ASSURE's good performance, it is needed only infrequently; the particular method of load balancing used does not substantially affect performance.

  20. Mercury source sector asssessment for the Greater Milwaukee Area

    SciTech Connect

    Obenauf, P.; Skavroneck, S.

    1997-09-01

    The Mercury Reduction Project for the Greater Milwaukee Area is a joint effort of the Pollution Prevention Partnership, Milwaukee Metropolitan Seweage District (MMSD) and Wisconsin Department of Natural Resources. Estimates of the amounts of mercury present, used and/or annually released to air, land and water within the MMSD service area are provided for 25 source sectors. This 420 square mile area (including Milwaukee County and parts of Waukesha, Racine, Ozaukee and Washington Counties) is home to just over 1 million people. The tables and figures summarize the relative amounts of mercury: annually released from purposeful uses; annually released due to trace impurities; and present or in use from the various source sectors in the Greater Milwaukee Area.

  1. Taxonomy of Greater White-fronted Geese (Aves: Anatidae)

    USGS Publications Warehouse

    Banks, Richard C.

    2011-01-01

    Five subspecies of the Greater White-fronted Goose, Anser albifrons (Scopoli, 1769), have been named, all on the basis of wintering birds, and up to six subspecies have been recognized. There has been confusion over the application of some names, particularly in North America, because of lack of knowledge of the breeding ranges and type localities, and incorrect taxonomic decisions. There is one clinally varying subspecies in Eurasia, one that breeds in Greenland, and three in North America, one newly named herein.

  2. Power Quality and Reliability Project

    NASA Technical Reports Server (NTRS)

    Attia, John O.

    2001-01-01

    One area where universities and industry can link is in the area of power systems reliability and quality - key concepts in the commercial, industrial and public sector engineering environments. Prairie View A&M University (PVAMU) has established a collaborative relationship with the University of'Texas at Arlington (UTA), NASA/Johnson Space Center (JSC), and EP&C Engineering and Technology Group (EP&C) a small disadvantage business that specializes in power quality and engineering services. The primary goal of this collaboration is to facilitate the development and implementation of a Strategic Integrated power/Systems Reliability and Curriculum Enhancement Program. The objectives of first phase of this work are: (a) to develop a course in power quality and reliability, (b) to use the campus of Prairie View A&M University as a laboratory for the study of systems reliability and quality issues, (c) to provide students with NASA/EPC shadowing and Internship experience. In this work, a course, titled "Reliability Analysis of Electrical Facilities" was developed and taught for two semesters. About thirty seven has benefited directly from this course. A laboratory accompanying the course was also developed. Four facilities at Prairie View A&M University were surveyed. Some tests that were performed are (i) earth-ground testing, (ii) voltage, amperage and harmonics of various panels in the buildings, (iii) checking the wire sizes to see if they were the right size for the load that they were carrying, (iv) vibration tests to test the status of the engines or chillers and water pumps, (v) infrared testing to the test arcing or misfiring of electrical or mechanical systems.

  3. Achievements in Stratospheric Ozone Protection

    EPA Pesticide Factsheets

    This report describes achievements in protecting the ozone layer, the benefits of these achievements, and strategies involved (e.g., using alternatives to ozone-depleting substances, phasing out harmful substances, and creating partnerships).

  4. Distribution of Permo-Carboniferous clastics of Greater Arabian basin

    SciTech Connect

    Al-Laboun, A.A.

    1987-05-01

    Strikingly correlative sequences of sediments composed of sandstones, siltstones, shales, and thin argillaceous carbonate beds are present, practically everywhere, underlying the Late Permian carbonates in the Greater Arabian basin. The Greater Arabian basin as defined here occupies the broad Arabian Shelf that borders the Arabian shield. This basin is composed of several smaller basins. These clastics are exposed as thin bands and scattered small exposures in several localities around the margins of the basin. The Permo-Carboniferous clastics are represented by the Unayzah Formation of Arabia, the Doubayat Group of Syria, the Hazro Formation of southeast Turkey, the Ga'arah Formation of Iraq, the Faraghan Formation of southwest Iran, and the Haushi Group of Oman. A Late Carboniferous-Early Permian age is assigned to these clastics because they contain fossil plants and palynomorphs. These sediments represent time-transgressive fluctuating sea deposits following a phase of regional emergence, erosion, and structural disturbance which preceded the Permian transgression. The basal contact of these clastics is marked by a well-pronounced angular unconformity with various older units, ranging in age from early Carboniferous to late Precambrian. This regional unconformity is probably related to the Hercynian movements. The upper contact is conformable with the Permian carbonates. The porous sandstones of the Permo-Carboniferous sediments are important hydrocarbon exploration targets. These reservoir rocks sometimes overlie mature source rocks and are capped by shales, marls, and tight carbonates. Significant quantities of hydrocarbons are contained in these reservoirs in different parts of the Greater Arabian basin.

  5. Assessing the geologic evolution of Greater Thaumasia, Mars

    NASA Astrophysics Data System (ADS)

    Hood, Don R.; Judice, Taylor; Karunatillake, Suniti; Rogers, Deanne; Dohm, James M.; Susko, David; Carnes, Lorraine K.

    2016-09-01

    The Greater Thaumasia region consists of three chemical provinces that include Syria, Solis, and Thaumasia Planae, the Corprates Rise, part of the Thaumasia Highlands, and the transition zone northwest of the Argyre basin. Chemical signatures obtained from the Mars Odyssey Gamma Ray Spectrometer suggest low abundances of K and Th to the west, with low H abundances and high Si abundances to the east, relative to the bulk Martian crust at midlatitudes. These observations are confirmed and quantified with a modified box and whisker analysis that simultaneously captures the degree of deviation and significance of the regionally anomalous chemistry. Motivated by regionally unique chemistry, as well as its diverse geological history, we characterize Greater Thaumasia in terms of chemistry, mineralogy, and mapped geology to determine how such complementary data record the evolution of this region. Our observations are inconsistent with a proposed salt-lubricated landslide origin, particularly given the lack of chemical or mineralogical signatures to support near-surface salt deposits that should arise over geological timescales. Our observations instead support magmatic processes, such as mantle evolution over geological time, which may impart the Si-enriched signature of the eastern portion of Greater Thaumasia as well as the K and Th depletion of the southeastern flank of Syria Planum. While the observed trend of decreasing K and Th from Noachian to Hesperian lavas is inconsistent with previous models of Martian mantle evolution, we see an increase in Ca content at the Noachian-Hesperian boundary, consistent with predictions from thermodynamic modeling.

  6. Integrating parasitology and marine ecology: Seven challenges towards greater synergy

    NASA Astrophysics Data System (ADS)

    Poulin, Robert; Blasco-Costa, Isabel; Randhawa, Haseeb S.

    2016-07-01

    Despite their very different historical origins as scientific disciplines, parasitology and marine ecology have already combined successfully to make important contributions to our understanding of the functioning of natural ecosystems. For example, robust assessments of the contribution of parasites to ecosystem biomass and energetics, and of their impact on community-wide biodiversity and food web structure, have all been made for the first time in marine systems. Nevertheless, for the marriage between parasitology and marine ecology to remain fruitful, several challenges must first be overcome. We discuss seven such challenges on the road to a greater synergy between these disciplines: (1) Raising awareness of parasitism as an ecological force by increasing the proportion of articles about parasites and diseases in marine ecology journals; (2) Making greater use of theory and conceptual frameworks from marine ecology to guide parasitological research; (3) Speeding up or at least maintaining the current rate at which marine parasites are found and described; (4) Elucidating a greater proportion of life cycles in all major groups of marine parasites; (5) Increasing the number of host-parasite model systems on which our knowledge is based; (6) Extending parasitological research offshore and into ocean depths; and (7) Developing, as needed, new epidemiological theory and transmission models for the marine environment. None of these challenges is insurmountable, and addressing just a few of them should guarantee that parasitology and marine ecology will continue to join forces and make further substantial contributions.

  7. Dietary phosphorus is associated with greater left ventricular mass.

    PubMed

    Yamamoto, Kalani T; Robinson-Cohen, Cassianne; de Oliveira, Marcia C; Kostina, Alina; Nettleton, Jennifer A; Ix, Joachim H; Nguyen, Ha; Eng, John; Lima, Joao A C; Siscovick, David S; Weiss, Noel S; Kestenbaum, Bryan

    2013-04-01

    Dietary phosphorus consumption has risen steadily in the United States. Oral phosphorus loading alters key regulatory hormones and impairs vascular endothelial function, which may lead to an increase in left ventricular mass (LVM). We investigated the association of dietary phosphorus with LVM in 4494 participants from the Multi-Ethnic Study of Atherosclerosis, a community-based study of individuals who were free of known cardiovascular disease. The intake of dietary phosphorus was estimated using a 120-item food frequency questionnaire and the LVM was measured using magnetic resonance imaging. Regression models were used to determine associations of estimated dietary phosphorus with LVM and left ventricular hypertrophy (LVH). Mean estimated dietary phosphorus intake was 1167 mg/day in men and 1017 mg/day in women. After adjustment for demographics, dietary sodium, total calories, lifestyle factors, comorbidities, and established LVH risk factors, each quintile increase in the estimated dietary phosphate intake was associated with an estimated 1.1 g greater LVM. The highest gender-specific dietary phosphorus quintile was associated with an estimated 6.1 g greater LVM compared with the lowest quintile. Higher dietary phosphorus intake was associated with greater odds of LVH among women, but not men. These associations require confirmation in other studies.

  8. Greater Green River basin well-site selection

    SciTech Connect

    Frohne, K.H.; Boswell, R.

    1993-12-31

    Recent estimates of the natural gas resources of Cretaceous low-permeability reservoirs of the Greater Green River basin indicate that as much as 5000 trillion cubic feet (Tcf) of gas may be in place (Law and others 1989). Of this total, Law and others (1989) attributed approximately 80 percent to the Upper Cretaceous Mesaverde Group and Lewis Shale. Unfortunately, present economic conditions render the drilling of many vertical wells unprofitable. Consequently, a three-well demonstration program, jointly sponsored by the US DOE/METC and the Gas Research Institute, was designed to test the profitability of this resource using state-of-the-art directional drilling and completion techniques. DOE/METC studied the geologic and engineering characteristics of ``tight`` gas reservoirs in the eastern portion of the Greater Green River basin in order to identify specific locations that displayed the greatest potential for a successful field demonstration. This area encompasses the Rocks Springs Uplift, Wamsutter Arch, and the Washakie and Red Desert (or Great Divide) basins of southwestern Wyoming. The work was divided into three phases. Phase 1 consisted of a regional geologic reconnaissance of 14 gas-producing areas encompassing 98 separate gas fields. In Phase 2, the top four areas were analyzed in greater detail, and the area containing the most favorable conditions was selected for the identification of specific test sites. In Phase 3, target horizons were selected for each project area, and specific placement locations were selected and prioritized.

  9. Reliability prediction for a class of highly reliable digital systems

    NASA Technical Reports Server (NTRS)

    White, Allan L.

    1992-01-01

    Three theorems which show that the reliability of a popular class of systems can be computed using small and simple models are presented. This class consists of systems that are assemblages of subsystems where each subsystem is a majority-voting threeplex plus spares or majority-voting fourplex plus spares. The theorems are error bounds for model reduction and simplification. The error bounds are given in terms of readily available system parameters. The three theorems have been applied to a system that has been used as an example that generates extremely large reliability models; the system considered is one version of AIPS (Advanced Information Processing System) for IAPSA (Integrated Airframe Propulsion System Architecture).

  10. Reliability prediction for a class of highly reliable digital systems

    NASA Astrophysics Data System (ADS)

    White, Allan L.

    Three theorems which show that the reliability of a popular class of systems can be computed using small and simple models are presented. This class consists of systems that are assemblages of subsystems where each subsystem is a majority-voting threeplex plus spares or majority-voting fourplex plus spares. The theorems are error bounds for model reduction and simplification. The error bounds are given in terms of readily available system parameters. The three theorems have been applied to a system that has been used as an example that generates extremely large reliability models; the system considered is one version of AIPS (Advanced Information Processing System) for IAPSA (Integrated Airframe Propulsion System Architecture).

  11. DOE Nuclear Weapon Reliability Definition: History, Description, and Implementation

    SciTech Connect

    Wright, D.L.; Cashen, J.J.; Sjulin, J.M.; Bierbaum, R.L.; Kerschen, T.J.

    1999-04-01

    The overarching goal of the Department of Energy (DOE) nuclear weapon reliability assessment process is to provide a quantitative metric that reflects the ability of the weapons to perform their intended function successfully. This white paper is intended to provide insight into the current and long-standing DOE definition of nuclear weapon reliability, which can be summarized as: The probability of achieving the specified yield, at the target, across the Stockpile-To-Target Sequence of environments, throughout the weapon's lifetime, assuming proper inputs.

  12. Reliability of sheet moulding composites (SMC) for the automotive industry

    NASA Astrophysics Data System (ADS)

    Lamanna, Giuseppe; Ceparano, Angelo; Sartore, Luciana

    2014-05-01

    The reliability of Sheet Moulding Composite (SMC) has been analysed by means of mechanical static and fatigue tests. SMCs showed substantial in-plane anisotropy either in terms of stiffness or strength reflecting the preferential orientation of the short fibres along the direction of the conveyor belt during the processing operations. The static data were modelled on a statistical basis assuming that the monotonic tensile strength follows a two-parameter Weibull distribution, while for the fatigue test we adopted a two parameters model already validated for Glass Fibre Reinforced Plastics (GFRP). Overall, the procedure indicated that he material reliability and its applicability limits can be achieved with a minimum of experimental tests.

  13. Preliminary study of the reliability of imaging charge coupled devices

    NASA Technical Reports Server (NTRS)

    Beall, J. R.; Borenstein, M. D.; Homan, R. A.; Johnson, D. L.; Wilson, D. D.; Young, V. F.

    1978-01-01

    Imaging CCDs are capable of low light level response and high signal-to-noise ratios. In space applications they offer the user the ability to achieve extremely high resolution imaging with minimum circuitry in the photo sensor array. This work relates the CCD121H Fairchild device to the fundamentals of CCDs and the representative technologies. Several failure modes are described, construction is analyzed and test results are reported. In addition, the relationship of the device reliability to packaging principles is analyzed and test data presented. Finally, a test program is defined for more general reliability evaluation of CCDs.

  14. Beyond the Inventory: An Interagency Collaboration to Reduce Greenhouse Gas Emissions in the Greater Yellowstone Area

    SciTech Connect

    Kandt, A.; Hotchkiss, E.; Fiebig, M.

    2010-10-01

    As one of the largest, intact ecosystems in the continental United States, land managers within the Greater Yellowstone Area (GYA) have recognized the importance of compiling and understanding agency greenhouse gas (GHG) emissions. The 10 Federal units within the GYA have taken an active role in compiling GHG inventories on a unit- and ecosystem-wide level, setting goals for GHG mitigation, and identifying mitigation strategies for achieving those goals. This paper details the processes, methodologies, challenges, solutions, and lessons learned by the 10 Federal units within the GYA throughout this ongoing effort.

  15. Measuring Emotions in Students' Learning and Performance: The Achievement Emotions Questionnaire (AEQ)

    ERIC Educational Resources Information Center

    Pekrun, Reinhard; Goetz, Thomas; Frenzel, Anne C.; Barchfeld, Petra; Perry, Raymond P.

    2011-01-01

    Aside from test anxiety scales, measurement instruments assessing students' achievement emotions are largely lacking. This article reports on the construction, reliability, internal validity, and external validity of the Achievement Emotions Questionnaire (AEQ) which is designed to assess various achievement emotions experienced by students in…

  16. Length and anatomic routes of the greater palatine canal as observed by cone beam computed tomography

    PubMed Central

    Sheikhi, Mahnaz; Zamaninaser, Asieh; Jalalian, Faranak

    2013-01-01

    Background: Greater palatine canal is used for maxillary nerve block. This procedure has some complications such as proptosis, blindness, and intravascular injection. This study aimed to determine the mean greater palatine canal length (CL) and its typical anatomic routes, as well as provide a reliable facial index for computing the CL by using cone beam computed tomography (CBCT) data. Materials and Methods: A total of 138 CBCT scans (65 females and 73 males) were evaluated. The path of the canal and the CL were determined by sex, age, and side. The mean distance from the inferior border of the infraorbital foramen (IOF) to the crest of alveolar bone between maxillary premolar(CMP) was measured and compared with the CL. Paired t-tests, independent t-test, and one-way analysis of variance (ANOVA) were used for statistical analysis. Results: The mean of CL was 31.82 ± 1.37 mm (31.70 ± 2.44 mm on the right side and 31.94 ± 2.40 mm on the left side), and the values were 32.49 ± 2.37 mm in males and 30.55 ± 1.76 mm among females (P = 0.001). The mean distance from the IOF to the CMP was 32.01 ± 2.18 mm, which was not significantly different to the CL (P = 0.336). Conclusions: The mean CL was significantly different according to sex and side. The mean distance from the IOF to CMP was significantly different according to sex. On comparing the mean distance from the IOF to the CMP with the CL, no significant difference was observed. Therefore, the mean distance from the IOF to CMP may be a reliable clinical index. PMID:23946729

  17. Reliability Assessment Approach for Stirling Convertors and Generators

    NASA Astrophysics Data System (ADS)

    Shah, Ashwin R.; Schreiber, Jeffrey G.; Zampino, Edward; Best, Timothy

    2003-01-01

    Stirling power conversion is being considered for use in a Radioisotope Power System (RPS) for deep space science missions because it offers a multifold increase in the conversion efficiency of heat to electric power. Quantifying the reliability of an RPS that utilizes Stirling power conversion technology is important to develop and demonstrate the capability for long-term success. A description of the Stirling power convertor is provided, along with a discussion about some of the key components. On-going efforts to understand component life, design variables at the component and system levels, and related sources and nature of uncertainties is discussed. The requirement for reliability is discussed, and some of the critical areas of concern are identified. A section on the objectives of the overall development of the performance model and computation of reliability is included to highlight the goals of this effort. Also, a viable physics based reliability plan to model the design level variable uncertainties at the component level and the system level is outlined, and potential benefits elucidated. The plan encompasses interaction of different disciplines, maintaining the physical and probabilistic correlations at all the levels, and a verification process based on rational short-term tests. Additionally, both top-down and bottom-up coherency has been maintained in order to follow the physics based design process and mission requirements. The outlined reliability assessment approach provides guidelines to improve the design and identifies governing variables to achieve high reliability in the SRG (Stirling Radioisotope Generator) design.

  18. Reliability-based lifetime maintenance of aging highway bridges

    NASA Astrophysics Data System (ADS)

    Enright, Michael P.; Frangopol, Dan M.

    2000-06-01

    As the nation's infrastructure continues to age, the cost of maintaining it at an acceptable safety level continues to increase. In the United States, about one of every three bridges is rated structurally deficient and/or functionally obsolete. It will require about 80 billion to eliminate the current backlog of bridge deficiencies and maintain repair levels. Unfortunately, the financial resources allocated for these activities fall extremely short of the demand. Although several existing and emerging NDT techniques are available to gather inspection data, current maintenance planning decisions for deficient bridges are based on data from subjective condition assessments and do not consider the reliability of bridge components and systems. Recently, reliability-based optimum maintenance planning strategies have been developed. They can be used to predict inspection and repair times to achieve minimum life-cycle cost of deteriorating structural systems. In this study, a reliability-based methodology which takes into account loading randomness and history, and randomness in strength and degradation resulting from aggressive environmental factors, is used to predict the time- dependent reliability of aging highway bridges. A methodology for incorporating inspection data into reliability predictions is also presented. Finally, optimal lifetime maintenance strategies are identified, in which optimal inspection/repair times are found based on minimum expected life-cycle cost under prescribed reliability constraints. The influence of discount rate on optimum solutions is evaluated.

  19. Reliability Assessment Approach for Stirling Convertors and Generators

    NASA Technical Reports Server (NTRS)

    Shah, Ashwin R.; Schreiber, Jeffrey G.; Zampino, Edward; Best, Timothy

    2004-01-01

    Stirling power conversion is being considered for use in a Radioisotope Power System for deep-space science missions because it offers a multifold increase in the conversion efficiency of heat to electric power. Quantifying the reliability of a Radioisotope Power System that utilizes Stirling power conversion technology is important in developing and demonstrating the capability for long-term success. A description of the Stirling power convertor is provided, along with a discussion about some of the key components. Ongoing efforts to understand component life, design variables at the component and system levels, related sources, and the nature of uncertainties is discussed. The requirement for reliability also is discussed, and some of the critical areas of concern are identified. A section on the objectives of the performance model development and a computation of reliability is included to highlight the goals of this effort. Also, a viable physics-based reliability plan to model the design-level variable uncertainties at the component and system levels is outlined, and potential benefits are elucidated. The plan involves the interaction of different disciplines, maintaining the physical and probabilistic correlations at all the levels, and a verification process based on rational short-term tests. In addition, both top-down and bottom-up coherency were maintained to follow the physics-based design process and mission requirements. The outlined reliability assessment approach provides guidelines to improve the design and identifies governing variables to achieve high reliability in the Stirling Radioisotope Generator design.

  20. Multi-mode reliability-based design of horizontal curves.

    PubMed

    Essa, Mohamed; Sayed, Tarek; Hussein, Mohamed

    2016-08-01

    Recently, reliability analysis has been advocated as an effective approach to account for uncertainty in the geometric design process and to evaluate the risk associated with a particular design. In this approach, a risk measure (e.g. probability of noncompliance) is calculated to represent the probability that a specific design would not meet standard requirements. The majority of previous applications of reliability analysis in geometric design focused on evaluating the probability of noncompliance for only one mode of noncompliance such as insufficient sight distance. However, in many design situations, more than one mode of noncompliance may be present (e.g. insufficient sight distance and vehicle skidding at horizontal curves). In these situations, utilizing a multi-mode reliability approach that considers more than one failure (noncompliance) mode is required. The main objective of this paper is to demonstrate the application of multi-mode (system) reliability analysis to the design of horizontal curves. The process is demonstrated by a case study of Sea-to-Sky Highway located between Vancouver and Whistler, in southern British Columbia, Canada. Two noncompliance modes were considered: insufficient sight distance and vehicle skidding. The results show the importance of accounting for several noncompliance modes in the reliability model. The system reliability concept could be used in future studies to calibrate the design of various design elements in order to achieve consistent safety levels based on all possible modes of noncompliance.

  1. Reliability and Maintainability Analysis of Fluidic Back-Up Flight Control System and Components.

    DTIC Science & Technology

    1981-09-01

    being used in various aircraft applications are demonstrating extremely high reliability. However, the unique design of new fluidic compo- nents results...in a very limited failure rate data base and prevents the determination of numerical values of fluidic system reliability at a sufficient confidence...Did. 6601 WWINlTTi’ G.ASUFIOATION OF TH PAGE (116 flm e UAK 80227-60 EXECUTIVE SUMMARY BACKGROUND High reliability in flight control systems is achieved

  2. Students’ Achievement Goals, Learning-Related Emotions and Academic Achievement

    PubMed Central

    Lüftenegger, Marko; Klug, Julia; Harrer, Katharina; Langer, Marie; Spiel, Christiane; Schober, Barbara

    2016-01-01

    In the present research, the recently proposed 3 × 2 model of achievement goals is tested and associations with achievement emotions and their joint influence on academic achievement are investigated. The study was conducted with 388 students using the 3 × 2 Achievement Goal Questionnaire including the six proposed goal constructs (task-approach, task-avoidance, self-approach, self-avoidance, other-approach, other-avoidance) and the enjoyment and boredom scales from the Achievement Emotion Questionnaire. Exam grades were used as an indicator of academic achievement. Findings from CFAs provided strong support for the proposed structure of the 3 × 2 achievement goal model. Self-based goals, other-based goals and task-approach goals predicted enjoyment. Task-approach goals negatively predicted boredom. Task-approach and other-approach predicted achievement. The indirect effects of achievement goals through emotion variables on achievement were assessed using bias-corrected bootstrapping. No mediation effects were found. Implications for educational practice are discussed. PMID:27199836

  3. Constrained Optimization of Average Arrival Time via a Probabilistic Approach to Transport Reliability

    PubMed Central

    Namazi-Rad, Mohammad-Reza; Dunbar, Michelle; Ghaderi, Hadi; Mokhtarian, Payam

    2015-01-01

    To achieve greater transit-time reduction and improvement in reliability of transport services, there is an increasing need to assist transport planners in understanding the value of punctuality; i.e. the potential improvements, not only to service quality and the consumer but also to the actual profitability of the service. In order for this to be achieved, it is important to understand the network-specific aspects that affect both the ability to decrease transit-time, and the associated cost-benefit of doing so. In this paper, we outline a framework for evaluating the effectiveness of proposed changes to average transit-time, so as to determine the optimal choice of average arrival time subject to desired punctuality levels whilst simultaneously minimizing operational costs. We model the service transit-time variability using a truncated probability density function, and simultaneously compare the trade-off between potential gains and increased service costs, for several commonly employed cost-benefit functions of general form. We formulate this problem as a constrained optimization problem to determine the optimal choice of average transit time, so as to increase the level of service punctuality, whilst simultaneously ensuring a minimum level of cost-benefit to the service operator. PMID:25992902

  4. Constrained Optimization of Average Arrival Time via a Probabilistic Approach to Transport Reliability.

    PubMed

    Namazi-Rad, Mohammad-Reza; Dunbar, Michelle; Ghaderi, Hadi; Mokhtarian, Payam

    2015-01-01

    To achieve greater transit-time reduction and improvement in reliability of transport services, there is an increasing need to assist transport planners in understanding the value of punctuality; i.e. the potential improvements, not only to service quality and the consumer but also to the actual profitability of the service. In order for this to be achieved, it is important to understand the network-specific aspects that affect both the ability to decrease transit-time, and the associated cost-benefit of doing so. In this paper, we outline a framework for evaluating the effectiveness of proposed changes to average transit-time, so as to determine the optimal choice of average arrival time subject to desired punctuality levels whilst simultaneously minimizing operational costs. We model the service transit-time variability using a truncated probability density function, and simultaneously compare the trade-off between potential gains and increased service costs, for several commonly employed cost-benefit functions of general form. We formulate this problem as a constrained optimization problem to determine the optimal choice of average transit time, so as to increase the level of service punctuality, whilst simultaneously ensuring a minimum level of cost-benefit to the service operator.

  5. The post-orgasmic prolactin increase following intercourse is greater than following masturbation and suggests greater satiety.

    PubMed

    Brody, Stuart; Krüger, Tillmann H C

    2006-03-01

    Research indicates that prolactin increases following orgasm are involved in a feedback loop that serves to decrease arousal through inhibitory central dopaminergic and probably peripheral processes. The magnitude of post-orgasmic prolactin increase is thus a neurohormonal index of sexual satiety. Using data from three studies of men and women engaging in masturbation or penile-vaginal intercourse to orgasm in the laboratory, we report that for both sexes (adjusted for prolactin changes in a non-sexual control condition), the magnitude of prolactin increase following intercourse is 400% greater than that following masturbation. The results are interpreted as an indication of intercourse being more physiologically satisfying than masturbation, and discussed in light of prior research reporting greater physiological and psychological benefits associated with coitus than with any other sexual activities.

  6. 78 FR 38311 - Reliability Technical Conference Agenda

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-26

    ... Energy Regulatory Commission Reliability Technical Conference Agenda Reliability Technical Docket No. AD13-6-000 Conference. North American Electric Docket No. RC11-6-004 Reliability Corporation. North American Electric Docket No. RR13-2-000 Reliability Corporation. Not consolidated. As announced in...

  7. 75 FR 71625 - System Restoration Reliability Standards

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-24

    ... Energy Regulatory Commission 18 CFR Part 40 System Restoration Reliability Standards November 18, 2010... to approve Reliability Standards EOP-001-1 (Emergency Operations Planning), EOP- 005-2 (System... Commission by the North American Electric Reliability Corporation, the Electric Reliability Organization...

  8. Neural Networks, Reliability and Data Analysis

    DTIC Science & Technology

    1993-01-01

    Neural network technology has been surveyed with the intent of determining the feasibility and impact neural networks may have in the area of...automated reliability tools. Data analysis capabilities of neural networks appear to be very applicable to reliability science due to similar mathematical...tendencies in data.... Neural networks , Reliability, Data analysis, Automated reliability tools, Automated intelligent information processing, Statistical neural network.

  9. Final report for CCS cross-layer reliability visioning study

    SciTech Connect

    Quinn, Heather M; Dehon, Andre; Carter, Nicj

    2010-12-20

    The geometric rate of improvement of transistor size and integrated circuit performance known as Moore's Law has been an engine of growth for our economy, enabling new products and services, creating new value and wealth, increasing safety, and removing menial tasks from our daily lives. Affordable, highly integrated components have enabled both life-saving technologies and rich entertainment applications. Anti-lock brakes, insulin monitors, and GPS-enabled emergency response systems save lives. Cell phones, internet appliances, virtual worlds, realistic video games, and mp3 players enrich our lives and connect us together. Over the past 40 years of silicon scaling, the increasing capabilities of inexpensive computation have transformed our society through automation and ubiquitous communications. Looking forward, increasing unpredictability threatens our ability to continue scaling integrated circuits at Moore's Law rates. As the transistors and wires that make up integrated circuits become smaller, they display both greater differences in behavior among devices designed to be identical and greater vulnerability to transient and permanent faults. Conventional design techniques expend energy to tolerate this unpredictability by adding safety margins to a circuit's operating voltage, clock frequency or charge stored per bit. However, the rising energy costs needed to compensate for increasing unpredictability are rapidly becoming unacceptable in today's environment where power consumption is often the limiting factor on integrated circuit performance and energy efficiency is a national concern. Reliability and energy consumption are both reaching key inflection points that, together, threaten to reduce or end the benefits of feature size reduction. To continue beneficial scaling, we must use a cross-layer, Jull-system-design approach to reliability. Unlike current systems, which charge every device a substantial energy tax in order to guarantee correct operation in

  10. Sexual predators, energy development, and conservation in greater Yellowstone.

    PubMed

    Berger, Joel; Beckmann, Jon P

    2010-06-01

    In the United States, as elsewhere, a growing debate pits national energy policy and homeland security against biological conservation. In rural communities the extraction of fossil fuels is often encouraged because of the employment opportunities it offers, although the concomitant itinerant workforce is often associated with increased wildlife poaching. We explored possible positive and negative factors associated with energy extraction in the Greater Yellowstone Ecosystem (GYE), an area known for its national parks, intact biological diversity, and some of the New World's longest terrestrial migrations. Specifically, we asked whether counties with different economies-recreation (ski), agrarian (ranching or farming), and energy extractive (petroleum)-differed in healthcare (gauged by the abundance of hospital beds) and in the frequency of sexual predators. The absolute and relative frequency of registered sex offenders grew approximately two to three times faster in areas reliant on energy extraction. Healthcare among counties did not differ. The strong conflation of community dishevel, as reflected by in-migrant sexual predators, and ecological decay in Greater Yellowstone is consistent with patterns seen in similar systems from Ecuador to northern Canada, where social and environmental disarray exist around energy boomtowns. In our case, that groups (albeit with different aims) mobilized campaigns to help maintain the quality of rural livelihoods by protecting open space is a positive sign that conservation can matter, especially in the face of rampant and poorly executed energy extraction projects. Our findings further suggest that the public and industry need stronger regulatory action to instill greater vigilance when and where social factors and land conversion impact biological systems.

  11. Practicing more retrieval routes leads to greater memory retention.

    PubMed

    Zheng, Jun; Zhang, Wei; Li, Tongtong; Liu, Zhaomin; Luo, Liang

    2016-09-01

    A wealth of research has shown that retrieval practice plays a significant role in improving memory retention. The current study focused on one simple yet rarely examined question: would repeated retrieval using two different retrieval routes or using the same retrieval route twice lead to greater long-term memory retention? Participants elaborately learned 22 Japanese-Chinese translation word pairs using two different mediators. Half an hour after the initial study phase, the participants completed two retrieval sessions using either one mediator (Tm1Tm1) or two different mediators (Tm1Tm2). On the final test, which was performed 1week after the retrieval practice phase, the participants received only the cue with a request to report the mediator (M1 or M2) followed by the target (Experiment 1) or only the mediator (M1 or M2) with a request to report the target (Experiment 2). The results of Experiment 1 indicated that the participants who practiced under the Tm1Tm2 condition exhibited greater target retention than those who practiced under the Tm1Tm1 condition. This difference in performance was due to the significant disadvantage in mediator retrieval and decoding of the unpracticed mediator under the Tm1Tm1 condition. Although mediators were provided to participants on the final test in Experiment 2, decoding of the unpracticed mediators remained less effective than decoding of the practiced mediators. We conclude that practicing multiple retrieval routes leads to greater memory retention than focusing on a single retrieval route. Thus, increasing retrieval variability during repeated retrieval practice indeed significantly improves long-term retention in a delay test.

  12. Land cover mapping of Greater Mesoamerica using MODIS data

    USGS Publications Warehouse

    Giri, Chandra; Jenkins, Clinton N.

    2005-01-01

    A new land cover database of Greater Mesoamerica has been prepared using moderate resolution imaging spectroradiometer (MODIS, 500 m resolution) satellite data. Daily surface reflectance MODIS data and a suite of ancillary data were used in preparing the database by employing a decision tree classification approach. The new land cover data are an improvement over traditional advanced very high resolution radiometer (AVHRR) based land cover data in terms of both spatial and thematic details. The dominant land cover type in Greater Mesoamerica is forest (39%), followed by shrubland (30%) and cropland (22%). Country analysis shows forest as the dominant land cover type in Belize (62%), Cost Rica (52%), Guatemala (53%), Honduras (56%), Nicaragua (53%), and Panama (48%), cropland as the dominant land cover type in El Salvador (60.5%), and shrubland as the dominant land cover type in Mexico (37%). A three-step approach was used to assess the quality of the classified land cover data: (i) qualitative assessment provided good insight in identifying and correcting gross errors; (ii) correlation analysis of MODIS- and Landsat-derived land cover data revealed strong positive association for forest (r2 = 0.88), shrubland (r2 = 0.75), and cropland (r2 = 0.97) but weak positive association for grassland (r2 = 0.26); and (iii) an error matrix generated using unseen training data provided an overall accuracy of 77.3% with a Kappa coefficient of 0.73608. Overall, MODIS 500 m data and the methodology used were found to be quite useful for broad-scale land cover mapping of Greater Mesoamerica.

  13. Greater Burgan of Kuwait: world's second largest oil field

    SciTech Connect

    Youash, Y.Y.

    1989-03-01

    Greater Burgan (Main burgan, Magwa, and Ahmadi) field is located in the Arabian Platform geologic province and the stable shelf tectonic environment of the Mesopotamian geosyncline, a sedimentary basin extending from the Arabian shield on the west to the complexly folded and faulted Zagros Mountains on the east. The structural development in Cretaceous time represents a major anticlinorium bounded by a basin to the west and a synclinorium to the east. Greater Burgan is located within this anticlinorium. The field consists of three dome structures 25 km wide and 65 km long with gentle dips of only few degrees. Faults have little throw and did not contribute to the trapping mechanism. The structural deformation may have been caused by halokinetic movements and most likely by basement block faulting that may have started in the Paleozoic. Greater Burgan was discovered in 1938. All production during the last 40 years has been by its natural pressure. Although natural gas injection has been carried out for some time, no waterflooding has been initiated yet. Recoverable reserves of the field are 87 billion bbl of oil. During the last 5 years giant reserves have been added in this field from the deeper strata of Jurassic age. Several deep wells have been drilled to the Permian for the purpose of discovering gas. So far, no Permian gas has been found in Kuwait. The Permian is 25,000 ft deep, and it is unlikely gas will be found there in the future. However, the potential of the Jurassic reservoirs will be a major target in the future. Also, there is a great possibility of discovering oil in stratigraphic traps, as several producing strata in the nearby fields pinch out on the flanks of this giant structure. Enhanced oil recovery should add significant reserves in the future.

  14. Gearbox Reliability Collaborative Bearing Calibration

    SciTech Connect

    van Dam, J.

    2011-10-01

    NREL has initiated the Gearbox Reliability Collaborative (GRC) to investigate the root cause of the low wind turbine gearbox reliability. The GRC follows a multi-pronged approach based on a collaborative of manufacturers, owners, researchers and consultants. The project combines analysis, field testing, dynamometer testing, condition monitoring, and the development and population of a gearbox failure database. At the core of the project are two 750kW gearboxes that have been redesigned and rebuilt so that they are representative of the multi-megawatt gearbox topology currently used in the industry. These gearboxes are heavily instrumented and are tested in the field and on the dynamometer. This report discusses the bearing calibrations of the gearboxes.

  15. Three approaches to reliability analysis

    NASA Technical Reports Server (NTRS)

    Palumbo, Daniel L.

    1989-01-01

    It is noted that current reliability analysis tools differ not only in their solution techniques, but also in their approach to model abstraction. The analyst must be satisfied with the constraints that are intrinsic to any combination of solution technique and model abstraction. To get a better idea of the nature of these constraints, three reliability analysis tools (HARP, ASSIST/SURE, and CAME) were used to model portions of the Integrated Airframe/Propulsion Control System architecture. When presented with the example problem, all three tools failed to produce correct results. In all cases, either the tool or the model had to be modified. It is suggested that most of the difficulty is rooted in the large model size and long computational times which are characteristic of Markov model solutions.

  16. Bioantioxidants: the systems reliability standpoint.

    PubMed

    Koltover, V K

    2009-01-01

    The antioxidant power of the so-called antioxidants is negligible because their rate constants and concentrations are too small to compete with the specialized defense enzymes, like superoxide dismutase (SOD), for the reactive oxygen species. In this short review, we present a number of experimental data of our group, along with the relevant literature data, to show that in-vivo antioxidants increase the systems reliability in other tacks. For example, butylated hydroxytoluene can prevent production of O2*- in mitochondria, whereas flavonoids can induce expression of antioxidant enzymes, SOD and catalase. We suggest that the timely introduction of antioxidants can provide the beneficial physiological effects through the prophylactic reliability maintenance against reactive forms of oxygen via the hormonal system.

  17. Assessment of NDE Reliability Data

    NASA Technical Reports Server (NTRS)

    Yee, B. G. W.; Chang, F. H.; Covchman, J. C.; Lemon, G. H.; Packman, P. F.

    1976-01-01

    Twenty sets of relevant Nondestructive Evaluation (NDE) reliability data have been identified, collected, compiled, and categorized. A criterion for the selection of data for statistical analysis considerations has been formulated. A model to grade the quality and validity of the data sets has been developed. Data input formats, which record the pertinent parameters of the defect/specimen and inspection procedures, have been formulated for each NDE method. A comprehensive computer program has been written to calculate the probability of flaw detection at several confidence levels by the binomial distribution. This program also selects the desired data sets for pooling and tests the statistical pooling criteria before calculating the composite detection reliability. Probability of detection curves at 95 and 50 percent confidence levels have been plotted for individual sets of relevant data as well as for several sets of merged data with common sets of NDE parameters.

  18. Ensuring reliability in expansion schemes.

    PubMed

    Kamal-Uddin, Abu Sayed; Williams, Donald Leigh

    2005-01-01

    Existing electricity power supplies must serve, or be adapted to serve, the expansion of hospital buildings. With the existing power supply assets of many hospitals being up to 20 years old, assessing the security and reliability of the power system must be given appropriate priority to avoid unplanned outages due to overloads and equipment failures. It is imperative that adequate contingency is planned for essential and non-essential electricity circuits. This article describes the methodology undertaken, and the subsequent recommendations that were made, when evaluating the security and reliability of electricity power supplies to a number of major London hospitals. The methodology described aligns with the latest issue of NHS Estates HTM 2011 'Primary Electrical Infrastructure Emergency Electrical Services Design Guidance' (to which ERA Technology has contributed).

  19. High-frequency audiometry: test reliability and procedural considerations.

    PubMed

    Stelmachowicz, P G; Beauchaine, K A; Kalberer, A; Kelly, W J; Jesteadt, W

    1989-02-01

    This study compared the reliability of a recently developed high-frequency audiometer (HFA) [Stevens et al., J. Acoust. Soc. Am. 81, 470-484 (1987)] with a less complicated system that uses supraaural earphones (Koss system). The new approach permits calibration on an individual basis, making it possible to express thresholds at high frequencies in dB SPL. Data obtained from 50 normal-hearing subjects, ranging in age from 10-60 years, were used to evaluate the effects on reliability of threshold variance, earpiece/earphone fitting variance, and the variance associated with the HFA calibration process. Without earpiece/earphone replacement, the reliability of thresholds for the two systems is similar. With replacement, the HFA showed poorer reliability than the Koss system above 11 kHz, largely due to errors in estimating the calibration function. HFA reliability is greater for subjects with valid calibration functions over the entire frequency range. When average correction factors are applied to the Koss data in an effort to convert threshold estimates to dB SPL, individual transfer functions are not represented accurately. Thus the benefit of being able to express thresholds at high frequencies in dB SPL must be weighed against the additional source of variability introduced by the HFA calibration process.

  20. Diverse Redundant Systems for Reliable Space Life Support

    NASA Technical Reports Server (NTRS)

    Jones, Harry W.

    2015-01-01

    Reliable life support systems are required for deep space missions. The probability of a fatal life support failure should be less than one in a thousand in a multi-year mission. It is far too expensive to develop a single system with such high reliability. Using three redundant units would require only that each have a failure probability of one in ten over the mission. Since the system development cost is inverse to the failure probability, this would cut cost by a factor of one hundred. Using replaceable subsystems instead of full systems would further cut cost. Using full sets of replaceable components improves reliability more than using complete systems as spares, since a set of components could repair many different failures instead of just one. Replaceable components would require more tools, space, and planning than full systems or replaceable subsystems. However, identical system redundancy cannot be relied on in practice. Common cause failures can disable all the identical redundant systems. Typical levels of common cause failures will defeat redundancy greater than two. Diverse redundant systems are required for reliable space life support. Three, four, or five diverse redundant systems could be needed for sufficient reliability. One system with lower level repair could be substituted for two diverse systems to save cost.

  1. Passalidae (Coleoptera: Scarabaeoidea) of the Greater and Lesser Antilles.

    PubMed

    Jiménez-Ferbans, Larry; Reyes-Castillo, Pedro; Schuster, Jack C

    2015-05-12

    We present a synthesis of the state of knowledge concerning the species of Passalidae (Coleoptera) of the West Indies and we present a key to the species. The recently described genus Antillanax Boucher renders the subgenus Passalus (Pertinax) Kaup paraphyletic, therefore we place Antillanax in synonymy with Passalus (Pertinax) and we propose a new combination for Passalus (Pertinax) doesburgi (Boucher). The island richest in species is Hispaniola, with five species, three of them endemic. Excluding Trinidad and Tobago, the passalid fauna of the West Indies comprises 13 species; this is low richness, but with high endemism (50%), especially for the Greater Antilles.

  2. Range-wide patterns of greater sage-grouse persistence

    USGS Publications Warehouse

    Aldridge, C.L.; Nielsen, S.E.; Beyer, H.L.; Boyce, M.S.; Connelly, J.W.; Knick, S.T.; Schroeder, M.A.

    2008-01-01

    Aim: Greater sage-grouse (Centrocercus urophasianus), a shrub-steppe obligate species of western North America, currently occupies only half its historical range. Here we examine how broad-scale, long-term trends in landscape condition have affected range contraction. Location: Sagebrush biome of the western USA. Methods: Logistic regression was used to assess persistence and extirpation of greater sage-grouse range based on landscape conditions measured by human population (density and population change), vegetation (percentage of sagebrush habitat), roads (density of and distance to roads), agriculture (cropland, farmland and cattle density), climate (number of severe and extreme droughts) and range periphery. Model predictions were used to identify areas where future extirpations can be expected, while also explaining possible causes of past extirpations. Results: Greater sage-grouse persistence and extirpation were significantly related to sagebrush habitat, cultivated cropland, human population density in 1950, prevalence of severe droughts and historical range periphery. Extirpation of sage-grouse was most likely in areas having at least four persons per square kilometre in 1950, 25% cultivated cropland in 2002 or the presence of three or more severe droughts per decade. In contrast, persistence of sage-grouse was expected when at least 30 km from historical range edge and in habitats containing at least 25% sagebrush cover within 30 km. Extirpation was most often explained (35%) by the combined effects of peripherality (within 30 km of range edge) and lack of sagebrush cover (less than 25% within 30 km). Based on patterns of prior extirpation and model predictions, we predict that 29% of remaining range may be at risk. Main Conclusions: Spatial patterns in greater sage-grouse range contraction can be explained by widely available landscape variables that describe patterns of remaining sagebrush habitat and loss due to cultivation, climatic trends, human

  3. Ultradeep (greater than 300 kilometers), ultramafic upper mantle xenoliths.

    PubMed

    Haggerty, S E; Sautter, V

    1990-05-25

    Geophysical discontinuities in Earth's upper mantle and experimental data predict the structural transformation of pyroxene to garnet and the solid-state dissolution of pyroxene into garnet with increasing depth. These predictions are indirectly verified by omphacitic pyroxene exsolution in pyropic garnet-bearing xenoliths from a diamondiferous kimberlite. Conditions for silicon in octahedral sites in the original garnets are met at pressures greater than 130 kilobars, placing the origin of these xenoliths at depths of 300 to 400 kilometers. These ultradeep xenoliths support the theory that the 400-km seismic discontinuity is marked by a transition from peridotite to eclogite.

  4. Greater Coordination Required in Defense Planning for Intratheather Airlift Needs.

    DTIC Science & Technology

    1981-07-09

    AD-AIOI 292 GENERAL ACCOUNTING OFFICE WASHINGTON DC PROCUREMENT -ETC F/6 15/5 GREATER COORDINATION REQUIRED IN DEFENSE PLANNING FOR INTRATHEA-(ETC(U...JUL 81 UNCLASSIFIED GAO/PLR-81-42 BY THE U.S. GENERAL ACCOUNTING OFFICE Report To The Secretary Of Defense Q reater Coordination Required In Defense...11~~~I~ LF’A RD-1-42/ I1CCU4S JULY 9, 1981’ / 81 7 13 331 I Request for copies of GAO reports should be sent to: U.S. General Accounting Office

  5. Nonelectronic Parts Reliability Data 1991

    DTIC Science & Technology

    1991-05-01

    design trade-off decisions involving factors such as cost , weight, power, performance, etc. A parts stress type prediction is typically refined to...provide a quantitative means of estimating the relative cost -benefit of these and other system level trade-off considerations. Predictions which are...Package Watt Wattage Freq Frequency Pop Population Wdg Winding Herm Hermeticity Pos Position X-Sec Cross Section Imp Impedance Reliability Analysis

  6. Reliability of Naval Radar Systems

    DTIC Science & Technology

    1978-09-01

    the driver uses as much prime power to produce a few watts as the output tube does to produce several kilo- watts. Large klystrons , such as the ones...ITEMS: transmitter ANTENNA SITE: 214 diam (7’) power resistors, sero amplifiers, ANTENNA GAIN (d): 41 encoder, klystron (4) POLARIZATION: horizontal...whM.ch will be developed are the differences in mission, power levels, stress, and costs allowed for the development and assurance of reliability. (U

  7. Reliability Research for Photovoltaic Modules

    NASA Technical Reports Server (NTRS)

    Ross, Ronald J., Jr.

    1986-01-01

    Report describes research approach used to improve reliability of photovoltaic modules. Aimed at raising useful module lifetime to 20 to 30 years. Development of cost-effective solutions to module-lifetime problem requires compromises between degradation rates, failure rates, and lifetimes, on one hand, and costs of initial manufacture, maintenance, and lost energy, on other hand. Life-cycle costing integrates disparate economic terms, allowing cost effectiveness to be quantified, allowing comparison of different design alternatives.

  8. Storage Reliability of Reserve Batteries

    DTIC Science & Technology

    2007-11-02

    batteries – Environmental concerns, lack of business – Non-availability of some critical materials • Lithium Oxyhalides are systems of choice – Good...exhibit good corrosion resistance to neutral electrolytes (LiAlCl4 in thionyl chloride and sulfuryl chloride ) • Using AlCl3 creates a much more corrosive...Storage Reliability of Reserve Batteries Jeff Swank and Allan Goldberg Army Research Laboratory Adelphi, MD 301-394-3116 jswank@arl.army.mil ll l

  9. Reliability Prediction for Aerospace Electronics

    DTIC Science & Technology

    2015-04-20

    methodology can be extended to include radiation effects, frequency, and even packaging and solder joint effects to give a complete system...assume that there is no failure analysis (FA) of the devices after the HTOL test, or that the manufacturer will not report FA results to the...effects, frequency and even packaging and solder joint effects to give a complete system reliability evaluation framework. This matrix gives a very

  10. LAMPF reliability history and program

    SciTech Connect

    van Dyck, O.

    1994-09-01

    Many years of service of the 800-MeV LAMPF H{sup +}/H{sup {minus}} linac offers the opportunity to evaluate the long-term reliability characteristics of a high-power machine, which with up to 800-kW beam power available is as close to an ADTT machine as exists in the world today. Records from the last 15 years of operation were analyzed for trends and areas of deteriorating reliability or disproportionate downtime and used to support engineering judgment on facility refurbishment to regain beam availability. This round of analysis has helped define a further level of detail and automation to be implemented in availability recording. Interesting features which emerge from the history include a clear measurement of the lower availability in the first operating cycle following extended maintenance periods, and a consistent picture of the highest availability to be expected in extended operating periods with the facility as used and maintained. The results provide a starting point for informed discussion of reliability goals.

  11. Test-Retest Reliability of a Computerized Concussion Test

    PubMed Central

    Littleton, Ashley C.; Register-Mihalik, Johna K.; Guskiewicz, Kevin M.

    2015-01-01

    Background: Neurocognitive testing is an important concussion evaluation tool, but for neurocognitive tests to be useful, their psychometric properties must be well established. Test-retest reliability of computerized neurocognitive tests can influence their clinical utility. The reliability for a commonly used computerized neurocognitive test, CNS Vital Signs, is not well established. The purpose of this study was to examine test-retest reliability and reliable change indices for CNS Vital Signs in a healthy, physically active college population. Hypothesis: CNS Vital Signs yields acceptable test-retest reliability, with greater reliability between the second and third test administration compared with between the first and second administration. Study Design: Cohort study. Level of Evidence: Level 3. Methods: Forty healthy, active volunteers (16 men, 24 women; mean age, 21.05 ± 2.17 years) reported to a clinical laboratory for 3 sessions, 1 week apart. At each session, participants were administered CNS Vital Signs. Outcomes included standard scores for the following CNS Vital Signs domains: verbal memory, visual memory, psychomotor speed, cognitive flexibility, complex attention, processing speed, reaction time, executive functioning, and reasoning. Results: Participants performed significantly better on the second session and/or third session than they did on the first testing session on 6 of 9 neurocognitive domains. Pearson r test-retest correlations between sessions ranged from 0.11 to 0.87. Intraclass correlation coefficients ranged from 0.10 to 0.86. Conclusion: Clinicians should consider using reliable change indices to account for practice effects, identify meaningful score changes due to pathology, and inform clinical decisions. Clinical Relevance: This study highlights the importance of clinicians understanding the psychometric properties of computerized neurocognitive tests when using them in the management of sport-related concussion. If CNS Vital

  12. Humanitarian information systems and emergencies in the Greater Horn of Africa: logical components and logical linkages.

    PubMed

    Maxwell, Daniel; Watkins, Ben

    2003-03-01

    Natural and man-made emergencies are regular occurrences in the Greater Horn of Africa region. The underlying impoverishment of whole populations is increasing, making it more difficult to distinguish between humanitarian crises triggered by shocks and those resulting from chronic poverty. Shocks and hazards can no longer be seen as one-off events that trigger a one-time response. In countries that are both poor and exposed to frequent episodes of debilitating drought or chronic conflict, information needs tend to be different from the straightforward early warning/commodity accounting models of information systems that have proven reliable in past emergencies. This paper describes the interdependent components of a humanitarian information system appropriate for this kind of complex environment, noting the analytical links between the components and operational links to programme and policy. By examining a series of case studies from the Greater Horn region, the paper demonstrates that systems lacking one or more of these components will fail to provide adequate information--and thus incur humanitarian costs. While information always comes with a cost, the price of poor information--or none--is higher. And in situations of chronic vulnerability, in which development interventions are likely to be interspersed with both safety nets and emergency interventions on a recurrent basis, investment in improved information is a good investment from both a humanitarian and a financial viewpoint.

  13. Greater-confinement disposal of low-level radioactive wastes

    SciTech Connect

    Trevorrow, L.E.; Gilbert, T.L.; Luner, C.; Merry-Libby, P.A.; Meshkov, N.K.; Yu, C.

    1985-01-01

    Low-level radioactive wastes include a broad spectrum of wastes that have different radionuclide concentrations, half-lives, and physical and chemical properties. Standard shallow-land burial practice can provide adequate protection of public health and safety for most low-level wastes, but a small volume fraction (about 1%) containing most of the activity inventory (approx.90%) requires specific measures known as ''greater-confinement disposal'' (GCD). Different site characteristics and different waste characteristics - such as high radionuclide concentrations, long radionuclide half-lives, high radionuclide mobility, and physical or chemical characteristics that present exceptional hazards - lead to different GCD facility design requirements. Facility design alternatives considered for GCD include the augered shaft, deep trench, engineered structure, hydrofracture, improved waste form, and high-integrity container. Selection of an appropriate design must also consider the interplay between basic risk limits for protection of public health and safety, performance characteristics and objectives, costs, waste-acceptance criteria, waste characteristics, and site characteristics. This paper presents an overview of the factors that must be considered in planning the application of methods proposed for providing greater confinement of low-level wastes. 27 refs.

  14. The State of Lithospheric Stress in Greater Thailand

    NASA Astrophysics Data System (ADS)

    Meyers, B.; Furlong, K. P.; Pananont, P.; Pornsopin, P.

    2013-12-01

    Thailand and its surrounding regions occupy an important, but often overlooked, location in terms of plate tectonics and lithospheric deformation. The lateral extrusion of Tibet southeastward and eastward along deep strike slip faults to the north and the Sumatra-Andaman subduction zone to the south and west bound the region of greater Thailand. While it is adjacent to some of the most seismically active plate boundaries and intra-plate regions on Earth, this region has experienced only a low level of background seismicity. Thus, the long-term seismic potential of greater Thailand remains highly uncertain. Although historic seismicity is one indicator for future seismicity it is not the only tool we have for determining seismic hazard; we can assess the state of lithospheric stress. The stress conditions in this apparent aseismic region will be controlled by the forces acting on it boundaries. We can analyze those conditions through a study of fault structure, earthquake activity, and kinematics in the boundary area. Using Global Seismic Network (GSN) data augmented with Thai seismic network data to constrain the kinematics, and numerical finite element modeling of crustal and lithospheric deformation of the region, we are able to determine to overall stress conditions. This stress model can be compared to the known fault states in Thailand to assess the potential for earthquake activity.

  15. BBilateral Neglected Anterior Shoulder Dislocation with Greater Tuberosity Fractures

    PubMed Central

    Upasani, Tejas; Bhatnagar, Abhinav; Mehta, Sonu

    2016-01-01

    Introduction: Shoulder dislocations are a very common entity in routine orthopaedic practice. Chronic unreduced anterior dislocations of the shoulder are not very common. Neurological and vascular complications may occur as a result of an acute anterior dislocation of the shoulder or after a while in chronic unreduced shoulder dislocation. Open reduction is indicated for most chronic shoulder dislocations. We report a case of neglected bilateral anterior shoulder dislocation with bilateral displaced greater tuberosity fracture. To the best of our knowledge, only a handful cases have been reported in literature with bilateral anterior shoulder dislocation with bilateral fractures. Delayed diagnosis/reporting is a scenario which makes the list even slimmer and management all the more challenging. Case Report: We report a case of a 35-year-old male who had bilateral anterior shoulder dislocation and bilateral greater tuberosity fracture post seizure and failed to report it for a period of 30 days. One side was managed conservatively with closed reduction and immobilization and the other side with open reduction. No neurovascular complications pre or post reduction of shoulder were seen. Conclusion: Shoulder dislocations should always be suspected post seizures and if found should be treated promptly. Treatment becomes difficult for any shoulder dislocation that goes untreated for considerable period of time PMID:27703939

  16. Occult fractures of the greater tuberosity of the humerus.

    PubMed

    Gumina, S; Carbone, S; Postacchini, F

    2009-02-01

    We studied the highest reported number of patients with occult fracture of the greater tuberosity of the humerus and we analysed why fracture was not diagnosed, shoulder function and prevalence of eventually associated rotator cuff tear (RCT). Twenty-four patients with a missed fracture of the greater tuberosity underwent MR study for a suspect RCT. We evaluated shoulder function and self-assessed comfort with the Constant score (CS) and Simple Shoulder Test (SST). Nine patients showed evidence of cuff tendinosis, 11 of partial (p) RCT (2: subscapularis; 6: supraspinatus and 3: supraspinatus and infraspinatus). All patients with pRCT were older than 40. Initially, the mean CS and SST were 54% and 5/12; at follow-up, values increased to 36% and 5 points. MR should be performed in patients apparently negative for fracture but with painful shoulders and decreased ROM. Of our patients, 45.8% had pRCT; nevertheless function recovery was verified in 16 weeks.

  17. Absorption spectrum of DNA for wavelengths greater than 300 nm

    SciTech Connect

    Sutherland, J.C.; Griffin, K.P.

    1981-06-01

    Although DNA absorption at wavelengths greater than 300 nm is much weaker than that at shorter wavelengths, this absorption seems to be responsible for much of the biological damage caused by solar radiation of wavelengths less than 320 nm. Accurate measurement of the absorption spectrum of DNA above 300 nm is complicated by turbidity characteristic of concentrated solutions of DNA. We have measured the absorption spectra of DNA from calf thymus, Clostridium perfringens, Escherichia coli, Micrococcus luteus, salmon testis, and human placenta using procedures which separate optical density due to true absorption from that due to turbidity. Above 300 nm, the relative absorption of DNA increases as a function of guanine-cytosine content, presumably because the absorption of guanine is much greater than the absorption of adenine at these wavelengths. This result suggests that the photophysical processes which follow absorption of a long-wavelength photon may, on the average, differ from those induced by shorter-wavelength photons. It may also explain the lower quantum yield for the killing of cells by wavelengths above 300 nm compared to that by shorter wavelengths.

  18. Greater focus needed on methane leakage from natural gas infrastructure

    PubMed Central

    Alvarez, Ramón A.; Pacala, Stephen W.; Winebrake, James J.; Chameides, William L.; Hamburg, Steven P.

    2012-01-01

    Natural gas is seen by many as the future of American energy: a fuel that can provide energy independence and reduce greenhouse gas emissions in the process. However, there has also been confusion about the climate implications of increased use of natural gas for electric power and transportation. We propose and illustrate the use of technology warming potentials as a robust and transparent way to compare the cumulative radiative forcing created by alternative technologies fueled by natural gas and oil or coal by using the best available estimates of greenhouse gas emissions from each fuel cycle (i.e., production, transportation and use). We find that a shift to compressed natural gas vehicles from gasoline or diesel vehicles leads to greater radiative forcing of the climate for 80 or 280 yr, respectively, before beginning to produce benefits. Compressed natural gas vehicles could produce climate benefits on all time frames if the well-to-wheels CH4 leakage were capped at a level 45–70% below current estimates. By contrast, using natural gas instead of coal for electric power plants can reduce radiative forcing immediately, and reducing CH4 losses from the production and transportation of natural gas would produce even greater benefits. There is a need for the natural gas industry and science community to help obtain better emissions data and for increased efforts to reduce methane leakage in order to minimize the climate footprint of natural gas. PMID:22493226

  19. Spatial variations in travel behavior within greater Toronto area

    SciTech Connect

    Ghaeli, R.; Hutchinson, B.G.

    1998-03-01

    Rapid suburbanization of housing and employment has produced severe traffic congestion in North American cities. One response to this problem in the greater Toronto area (GTA) has been to identify urban forms that are more supportive of public transport and require less vehicle kilometers of travel to support. The analytical tools used to assess the travel implications of different urban forms normally use travel demand parameters that are uniform across an area. This has yielded misleading estimates of travel demands. This paper describes analyses of the intraregional differences in travel behavior in the greater Toronto area. The analyses described are at two spatial scales: the suburb (municipality/planning district) level and the much finer traffic analysis zone level. The analysis units were grouped into high-growth, developing,a nd low-growth categories at both spatial scales. The analyses reported in this paper show that household characteristics and travel behavior are quite similar for both established and redeveloping zones in the older, stable suburbs. Significant differences in travel characteristics exist between the older, established zones and the growing zones in the developing suburbs. Household trip rates are shown to vary with household size, car ownership, and whether a household is located in a stable or growing suburb. Accessibility to public transport is shown to affect trip behavior differently in growing areas than in established areas. The paper concludes by discussing the public policy and transport systems analysis implications of the results.

  20. Greater focus needed on methane leakage from natural gas infrastructure.

    PubMed

    Alvarez, Ramón A; Pacala, Stephen W; Winebrake, James J; Chameides, William L; Hamburg, Steven P

    2012-04-24

    Natural gas is seen by many as the future of American energy: a fuel that can provide energy independence and reduce greenhouse gas emissions in the process. However, there has also been confusion about the climate implications of increased use of natural gas for electric power and transportation. We propose and illustrate the use of technology warming potentials as a robust and transparent way to compare the cumulative radiative forcing created by alternative technologies fueled by natural gas and oil or coal by using the best available estimates of greenhouse gas emissions from each fuel cycle (i.e., production, transportation and use). We find that a shift to compressed natural gas vehicles from gasoline or diesel vehicles leads to greater radiative forcing of the climate for 80 or 280 yr, respectively, before beginning to produce benefits. Compressed natural gas vehicles could produce climate benefits on all time frames if the well-to-wheels CH(4) leakage were capped at a level 45-70% below current estimates. By contrast, using natural gas instead of coal for electric power plants can reduce radiative forcing immediately, and reducing CH(4) losses from the production and transportation of natural gas would produce even greater benefits. There is a need for the natural gas industry and science community to help obtain better emissions data and for increased efforts to reduce methane leakage in order to minimize the climate footprint of natural gas.

  1. Greater Platte River Basins - Science to Sustain Ecosystems and Communities

    USGS Publications Warehouse

    Thormodsgard, June M.

    2009-01-01

    The Greater Platte River Basins (GPRB), located in the heartland of the United States, provides a collaborative opportunity for the U.S. Geological Survey (USGS) and its partners to understand the sustainability of natural and managed ecosystems under changing climate and resource requirements.The Greater Platte River Basins, an area of about 140,000 square miles, sustains thousands of acres of lakes and wetlands, which provide a staging and resting area for the North American Central Flyway. Part of the GPRB is within the U.S. Corn Belt, one of the most productive agricultural ecosystems on Earth. Changes in water and land use, changing patterns of snowmelt in the Rocky Mountains, drought, and increasing demands for irrigation have reduced flows in the Platte River. These changes raise questions about the sustainability of the region for both wildlife and agriculture.The USGS and partners are developing a science strategy that will help natural-resource managers address and balance the needs of this region.

  2. Liver metal concentrations in Greater Sage-grouse (Centrocercus urophasianus).

    PubMed

    Dailey, Rebecca N; Raisbeck, Merl F; Siemion, Roger S; Cornish, Todd E

    2008-04-01

    Greater Sage-grouse (Centrocercus urophasianus) are a species of concern due to shrinking populations associated with habitat fragmentation and loss. Baseline health parameters for this species are limited or lacking, especially with regard to tissue metal concentrations. To obtain a range of tissue metal concentrations, livers were collected from 71 Greater Sage-grouse from Wyoming and Montana. Mean +/- SE metal concentrations (mg/kg wet weight) in liver were determined for vanadium (V) (0.12 +/- 0.01), chromium (Cr) (0.50 +/- 0.02), manganese (Mn) (2.68 +/- 0.11), iron (Fe) (1,019 +/- 103), nickel (Ni) (0.40 +/- 0.04), cobalt (Co) (0.08 +/- 0.02), copper (Cu) (6.43 +/- 0.40), mercury (Hg) (0.30 +/- 0.09), selenium (Se) (1.45 +/- 0.64), zinc (Zn) (59.2 +/- 4.70), molybdenum (Mo) (0.93 +/- 0.07), cadmium (Cd) (1.44 +/- 0.14), barium (Ba) (0.20 +/- 0.03), and lead (Pb) (0.17 +/- 0.03). In addition to providing baseline data, metal concentrations were compared between sex, age (juvenile/adult), and West Nile virus (WNv) groups (positive/negative). Adult birds had higher concentrations of Ni and Cd compared to juveniles. In addition, Zn and Cu concentrations were significantly elevated in WNv-positive birds.

  3. Improvement of the Reliability of Dielectrics for MLCC

    NASA Astrophysics Data System (ADS)

    Nakamura, Tomoyuki; Yao, Takayuki; Ikeda, Jun; Kubodera, Noriyuki; Takagi, Hiroshi

    2011-10-01

    To achieve enough reliability of monolithic ceramic capacitor, it is important to know the contribution of grain boundary and grain interior to its reliability and insulation resistance. As the number of grain boundaries per layer increased, mean time to failure (MTTF) increased. In addition, as the number of grain boundaries per layer increased, samples showed lower current leakage in the measured electric field range. Using these data, the grain boundary E-J curves were determined by simulation. As a result, temperature and electric field dependence of insulation resistance of grain boundary were very low. The insulation characteristics of one BaTiO3 grain per layer were examined. The resistance and reliability of grain interior were very low. To improve the degradation resistance of grain interior, Ca-doped BaTiO3-based dielectrics were developed. The influence of Ca substitution on MTTF was investigated and it was found out that MTTF increased with the increase of Ca substitution.

  4. The Mechanics of Human Achievement.

    PubMed

    Duckworth, Angela L; Eichstaedt, Johannes C; Ungar, Lyle H

    2015-07-01

    Countless studies have addressed why some individuals achieve more than others. Nevertheless, the psychology of achievement lacks a unifying conceptual framework for synthesizing these empirical insights. We propose organizing achievement-related traits by two possible mechanisms of action: Traits that determine the rate at which an individual learns a skill are talent variables and can be distinguished conceptually from traits that determine the effort an individual puts forth. This approach takes inspiration from Newtonian mechanics: achievement is akin to distance traveled, effort to time, skill to speed, and talent to acceleration. A novel prediction from this model is that individual differences in effort (but not talent) influence achievement (but not skill) more substantially over longer (rather than shorter) time intervals. Conceptualizing skill as the multiplicative product of talent and effort, and achievement as the multiplicative product of skill and effort, advances similar, but less formal, propositions by several important earlier thinkers.

  5. The Mechanics of Human Achievement

    PubMed Central

    Duckworth, Angela L.; Eichstaedt, Johannes C.; Ungar, Lyle H.

    2015-01-01

    Countless studies have addressed why some individuals achieve more than others. Nevertheless, the psychology of achievement lacks a unifying conceptual framework for synthesizing these empirical insights. We propose organizing achievement-related traits by two possible mechanisms of action: Traits that determine the rate at which an individual learns a skill are talent variables and can be distinguished conceptually from traits that determine the effort an individual puts forth. This approach takes inspiration from Newtonian mechanics: achievement is akin to distance traveled, effort to time, skill to speed, and talent to acceleration. A novel prediction from this model is that individual differences in effort (but not talent) influence achievement (but not skill) more substantially over longer (rather than shorter) time intervals. Conceptualizing skill as the multiplicative product of talent and effort, and achievement as the multiplicative product of skill and effort, advances similar, but less formal, propositions by several important earlier thinkers. PMID:26236393

  6. Structure contour map of the greater Green River basin, Wyoming, Colorado, and Utah

    USGS Publications Warehouse

    Lickus, M.R.; Law, B.E.

    1988-01-01

    The Greater Green River basin of Wyoming, Colorado, and Utah contains five basins and associated major uplifts (fig. 1). Published structure maps of the region have commonly used the top of the Lower Cretaceous Dakota Sandstone as a structural datum (Petroleum Ownership Map Company (POMCO), 1984; Rocky Mountain Association of Geologists, 1972). However, because relatively few wells in this area penetrate the Dakota, the Dakota structural datum has to be constructed by projecting down from shallower wells. Extrapolating in this manner may produce errors in the map. The primary purpose of this report is to present a more reliable structure contour map of the Greater Green River basin based on datums that are penetrated by many wells. The final map shows the large- to small-scale structures present in the Greater Green River basin. The availability of subsurface control and the map scale determined whether or not a structural feature was included on the map. In general, large structures such as the Moxa arch, Pinedale anticline, and other large folds were placed on the map based solely on the structure contours. In comparison, smaller folds and some faults were placed on the map based on structure contours and other reports (Bader 1987; Bradley 1961; Love and Christiansen, 1985; McDonald, 1975; Roehler, 1979; Wyoming Geological Association Oil and Gas Symposium Committee, 1979). State geologic maps and other reports were used to position basin margin faults (Bryant, 1985; Gries, 1983a, b; Hansen 1986; Hintze, 1980; Love and Christiansen, 1985; Tweto, 1979, 1983). In addition, an interpreted east-west-trending regional seismic line by Garing and Tainter (1985), which shows the basin configuration in cross-section, was helpful in locating buried faults, such as the high-angle reverse or thrust fault along the west flank of the Rock Springs uplift.

  7. Mapping grasslands suitable for cellulosic biofuels in the Greater Platte River Basin, United States

    USGS Publications Warehouse

    Wylie, Bruce K.; Gu, Yingxin

    2012-01-01

    Biofuels are an important component in the development of alternative energy supplies, which is needed to achieve national energy independence and security in the United States. The most common biofuel product today in the United States is corn-based ethanol; however, its development is limited because of concerns about global food shortages, livestock and food price increases, and water demand increases for irrigation and ethanol production. Corn-based ethanol also potentially contributes to soil erosion, and pesticides and fertilizers affect water quality. Studies indicate that future potential production of cellulosic ethanol is likely to be much greater than grain- or starch-based ethanol. As a result, economics and policy incentives could, in the near future, encourage expansion of cellulosic biofuels production from grasses, forest woody biomass, and agricultural and municipal wastes. If production expands, cultivation of cellulosic feedstock crops, such as switchgrass (Panicum virgatum L.) and miscanthus (Miscanthus species), is expected to increase dramatically. The main objective of this study is to identify grasslands in the Great Plains that are potentially suitable for cellulosic feedstock (such as switchgrass) production. Producing ethanol from noncropland holdings (such as grassland) will minimize the effects of biofuel developments on global food supplies. Our pilot study area is the Greater Platte River Basin, which includes a broad range of plant productivity from semiarid grasslands in the west to the fertile corn belt in the east. The Greater Platte River Basin was the subject of related U.S. Geological Survey (USGS) integrated research projects.

  8. Radical Dissection of Greater Palatine Artery and Dynamic Reconstruction of Cleft Palate

    PubMed Central

    Gill, Nauman Ahmad; Chaudry, Ayesha; Ishaq, Irfan; Aslam, Muhammad; Shamim, Romaisa; Kafeel, Mirza Muhammad; Aazam, Muhammad; Sailer, Hermann; Ganatra, Muhammad Ashraf

    2017-01-01

    Background: Restoration of proper anatomy and physiology is an integral part of cleft palate repair. The senior author has devised a new technique of radical release of greater palatine vessels, which helps in achieving tension-free closure of palatal cleft. In addition, release and transposition of palatal muscles is performed without the use of operative microscope, resulting in improved palatal function. This technique is applicable to all types of clefts of the palate and can be performed on adult patients as well. Materials and Methods: This is a retrospective case series of cleft palate repairs performed over a period of 3 years. Single-stage repair with modified Bardach’s technique for complete cleft palate and von Langenbeck’s technique for incomplete cleft palate with radical release of greater palatine vessels and levator complex retropositioning was performed. The outcome measures were closure of palatal defect and speech production. A follow-up of at least 6 months was completed in each patient. Results: A total of 1568 patients were included in the study. Their age ranged from 9 months to 54 years. The overall fistula rate was 6.1%. Improvement of speech was observed even in adult patients. Conclusions: Radical release of greater palatine artery and levator complex transposition can dramatically improve results of cleft palate repair. This technique helps in dynamic reconstruction of cleft palate and can be effectively applied in all age groups. PMID:28280675

  9. Stable Same-Sex Friendships with Higher Achieving Partners Promote Mathematical Reasoning in Lower Achieving Primary School Children

    PubMed Central

    DeLay, Dawn; Laursen, Brett; Kiuru, Noona; Poikkeus, Anna-Maija; Aunola, Kaisa; Nurmi, Jari-Erik

    2015-01-01

    This study is designed to investigate friend influence over mathematical reasoning in a sample of 374 children in 187 same-sex friend dyads (184 girls in 92 friendships; 190 boys in 95 friendships). Participants completed surveys that measured mathematical reasoning in the 3rd grade (approximately 9 years old) and one year later in the 4th grade (approximately 10 years old). Analyses designed for dyadic data (i.e., longitudinal Actor-Partner Interdependence Models) indicated that higher achieving friends influenced the mathematical reasoning of lower achieving friends, but not the reverse. Specifically, greater initial levels of mathematical reasoning among higher achieving partners in the 3rd grade predicted greater increases in mathematical reasoning from 3rd grade to 4th grade among lower achieving partners. These effects held after controlling for peer acceptance and rejection, task avoidance, interest in mathematics, maternal support for homework, parental education, length of the friendship, and friendship group norms on mathematical reasoning. PMID:26402901

  10. Applicability and Limitations of Reliability Allocation Methods

    NASA Technical Reports Server (NTRS)

    Cruz, Jose A.

    2016-01-01

    Reliability allocation process may be described as the process of assigning reliability requirements to individual components within a system to attain the specified system reliability. For large systems, the allocation process is often performed at different stages of system design. The allocation process often begins at the conceptual stage. As the system design develops, more information about components and the operating environment becomes available, different allocation methods can be considered. Reliability allocation methods are usually divided into two categories: weighting factors and optimal reliability allocation. When properly applied, these methods can produce reasonable approximations. Reliability allocation techniques have limitations and implied assumptions that need to be understood by system engineers. Applying reliability allocation techniques without understanding their limitations and assumptions can produce unrealistic results. This report addresses weighting factors, optimal reliability allocation techniques, and identifies the applicability and limitations of each reliability allocation technique.

  11. Low glucose relates to greater aggression in married couples.

    PubMed

    Bushman, Brad J; Dewall, C Nathan; Pond, Richard S; Hanus, Michael D

    2014-04-29

    Intimate partner violence affects millions of people globally. One possible contributing factor is poor self-control. Self-control requires energy, part of which is provided by glucose. For 21 days, glucose levels were measured in 107 married couples. To measure aggressive impulses, each evening participants stuck between 0 and 51 pins into a voodoo doll that represented their spouse, depending how angry they were with their spouse. To measure aggression, participants competed against their spouse on a 25-trial task in which the winner blasted the loser with loud noise through headphones. As expected, the lower the level of glucose in the blood, the greater number of pins participants stuck into the voodoo doll, and the higher intensity and longer duration of noise participants set for their spouse.

  12. Discrimination reversal learning reveals greater female behavioural flexibility in guppies

    PubMed Central

    Lucon-Xiccato, Tyrone; Bisazza, Angelo

    2014-01-01

    Behavioural flexibility allows an animal to adapt its behaviour in response to changes in the environment. Research conducted in primates, rodents and domestic fowl suggests greater behavioural persistence and reduced behavioural flexibility in males. We investigated sex differences in behavioural flexibility in fish by comparing male and female guppies (Poecilia reticulata) in a reversal learning task. Fish were first trained on a colour discrimination, which was learned equally rapidly by males and females. However, once the reward contingency was reversed, females were better at inhibiting the previous response and reached criterion twice as fast as males. When reward reversing was repeated, males gradually reduced the number of errors, and the two sexes had a comparable performance after four reversals. We suggest that sex differences in behavioural flexibility in guppies can be explained in terms of the different roles that males and females play in reproduction.

  13. Lakes in the greater Denver area, Front Range Urban Corridor

    USGS Publications Warehouse

    Danielson, T.W.

    1975-01-01

    The purpose of this report is to present the results of an inventory of the lakes in the central one-third of the Colorado Front Range Urban Corridor. This inventory provides information that might be helpful in planning the best and most beneficial use of lakes in an area of rapid population growth. The report includes data on lake size and water quality. Size data are included on most of the lakes of 2 hectares (20,000 m2, or about 5 acres) or greater, and water-quality data are provided on most lakes larger than 10 hectares (about 25 acres). Bodies of water resulting form excavation of gravel (borrow pits) were generally not included in the inventory.

  14. The Greater Plains Collaborative: a PCORnet Clinical Research Data Network.

    PubMed

    Waitman, Lemuel R; Aaronson, Lauren S; Nadkarni, Prakash M; Connolly, Daniel W; Campbell, James R

    2014-01-01

    The Greater Plains Collaborative (GPC) is composed of 10 leading medical centers repurposing the research programs and informatics infrastructures developed through Clinical and Translational Science Award initiatives. Partners are the University of Kansas Medical Center, Children's Mercy Hospital, University of Iowa Healthcare, the University of Wisconsin-Madison, the Medical College of Wisconsin and Marshfield Clinic, the University of Minnesota Academic Health Center, the University of Nebraska Medical Center, the University of Texas Health Sciences Center at San Antonio, and the University of Texas Southwestern Medical Center. The GPC network brings together a diverse population of 10 million people across 1300 miles covering seven states with a combined area of 679 159 square miles. Using input from community members, breast cancer was selected as a focus for cohort building activities. In addition to a high-prevalence disorder, we also selected a rare disease, amyotrophic lateral sclerosis.

  15. Slimness is associated with greater intercourse and lesser masturbation frequency.

    PubMed

    Brody, Stuart

    2004-01-01

    I examined the relationship of recalled and diary recorded frequency of penile-vaginal intercourse (FSI), noncoital partnered sexual activity, and masturbation to measured waist and hip circumference in 120 healthy adults aged 19-38. Slimmer waist (in men and in the sexes combined) and slimmer hips (in men and women) were associated with greater FSI. Slimmer waist and hips were associated with rated importance of intercourse for men. Noncoital partnered sexual activity had a less consistent association with slimness. Slimmer waist and hips were associated with less masturbation (in men and in the sexes combined). I discuss the results in terms of differences between different sexual behaviors, attractiveness, emotional relatedness, physical sensitivity, sexual dysfunction, sociobiology, psychopharmacological aspects of excess fat and carbohydrate consumption, and implications for sex therapy.

  16. Risks of Brucella abortus spillover in the Greater Yellowstone area.

    PubMed

    Schumaker, B

    2013-04-01

    Recurrent spillover of Brucella abortus from wildlife reservoirs to domestic cattle in the Greater Yellowstone Area (GYA) has prevented the United States from completely eradicating bovine brucellosis. Risks to cattle are a function of the size and location of wildlife and livestock populations, the degree and nature of spatio-temporal interactions between the various hosts, the level of disease in wildlife, and the susceptibility of livestock herds. While the brucellosis prevalence in wild, free-ranging GYA bison (Bison bison) is high, current management actions have successfully limited contact between bison and cattle. Under current management practices, the risks to cattle in the GYA are predominantly from wild elk (Cervus elaphus). Intra- and inter-species transmission events, while uncommon, are nevertheless crucial for the maintenance of brucellosis in the GYA. Future management actions should focus on decreasing elk herd densities and group sizes and on understanding the behavioural and environmental drivers that result in co-mingling that makes transmission possible.

  17. Depressed adolescents demonstrate greater subgenual anterior cingulate activity

    PubMed Central

    Yang, Tony T.; Simmons, Alan N.; Matthews, Scott C.; Tapert, Susan F.; Frank, Guido K.; Bischoff-Grethe, Amanda; Lansing, Amy E.; Wu, Jing; Brown, Gregory G.; Paulus, Martin P.

    2009-01-01

    Neuroimaging studies implicate the subgenual anterior cingulate cortex (sgACC) as a critical brain region in adult depression. However, unlike adult depression, little is known about the underlying neural substrates of adolescent depression, and there are no published data examining differences in sgACC activation between depressed and healthy adolescents. This study used functional magnetic resonance imaging to examine sgACC activity in twenty-six depressed and normal 13- to 17-year olds during the performance of a stop-signal task. Significantly greater sgACC activation was found in the depressed adolescents relative to controls. These results establish for the first time abnormal functioning of the sgACC in depressed adolescents and have important implications for understanding the underlying neural correlates and potential treatments of adolescent depression. PMID:19218875

  18. Evil genius? How dishonesty can lead to greater creativity.

    PubMed

    Gino, Francesca; Wiltermuth, Scott S

    2014-04-01

    We propose that dishonest and creative behavior have something in common: They both involve breaking rules. Because of this shared feature, creativity may lead to dishonesty (as shown in prior work), and dishonesty may lead to creativity (the hypothesis we tested in this research). In five experiments, participants had the opportunity to behave dishonestly by overreporting their performance on various tasks. They then completed one or more tasks designed to measure creativity. Those who cheated were subsequently more creative than noncheaters, even when we accounted for individual differences in their creative ability (Experiment 1). Using random assignment, we confirmed that acting dishonestly leads to greater creativity in subsequent tasks (Experiments 2 and 3). The link between dishonesty and creativity is explained by a heightened feeling of being unconstrained by rules, as indicated by both mediation (Experiment 4) and moderation (Experiment 5).

  19. Ovarian follicle dynamics of female Greater Scaup during egg production

    USGS Publications Warehouse

    Gorman, K.B.; Flint, P.L.; Esler, Daniel; Williams, T.D.

    2007-01-01

    Studies of female waterfowl nutrient reserve use during egg production require a precise understanding of ovarian follicle dynamics to correctly interpret breeding status, and, therefore, derive proper inference. Concerns over numerical declines of North American scaup have increased the need to better understand the role of female condition in reproductive performance. We quantified ovarian follicle dynamics of female Greater Scaup (Aythya marila) breeding on the Yukon–Kuskokwim Delta, Alaska, using a method that accounts for within day variation in follicle size. We considered several models for describing changes in follicle growth with the best supported model estimating the duration of rapid follicle growth (RFG) to be 5.20 ± 0.52 days (±95% confidence intervals) for each developing follicle. Average diameter and dry mass of preovulatory follicles were estimated to be 9.36 mm and 0.26 g, respectively, at the onset of RFG, and these follicle characteristics were 41.47 mm and 15.57 g, respectively, at ovulation. The average diameter of postovulatory follicles immediately following ovulation was estimated to be 17.35 mm, regressing quickly over several days. In addition, we derived predictive equations using diameter and dry mass to estimate the number of days before, and after, ovulation for pre- and postovulatory follicles, as well as an equation to estimate dry mass of damaged follicles. Our results allow precise definition of RFG and nest initiation dates, clutch size, and the daily energetic and nutritional demands of egg production at the individual level. This study provides the necessary foundation for additional work on Greater Scaup reproductive energetics and physiology, and offers an approach for quantifying ovarian follicle dynamics in other species.

  20. Greater learnability is not sufficient to produce cultural universals.

    PubMed

    Rafferty, Anna N; Griffiths, Thomas L; Ettlinger, Marc

    2013-10-01

    Looking across human societies reveals regularities in the languages that people speak and the concepts that they use. One explanation that has been proposed for these "cultural universals" is differences in the ease with which people learn particular languages and concepts. A difference in learnability means that languages and concepts possessing a particular property are more likely to be accurately transmitted from one generation of learners to the next. Intuitively, this difference could allow languages and concepts that are more learnable to become more prevalent after multiple generations of cultural transmission. If this is the case, the prevalence of languages and concepts with particular properties can be explained simply by demonstrating empirically that they are more learnable. We evaluate this argument using mathematical analysis and behavioral experiments. Specifically, we provide two counter-examples that show how greater learnability need not result in a property becoming prevalent. First, more learnable languages and concepts can nonetheless be less likely to be produced spontaneously as a result of transmission failures. We simulated cultural transmission in the laboratory to show that this can occur for memory of distinctive items: these items are more likely to be remembered, but not generated spontaneously once they have been forgotten. Second, when there are many languages or concepts that lack the more learnable property, sheer numbers can swamp the benefit produced by greater learnability. We demonstrate this using a second series of experiments involving artificial language learning. Both of these counter-examples show that simply finding a learnability bias experimentally is not sufficient to explain why a particular property is prevalent in the languages or concepts used in human societies: explanations for cultural universals based on cultural transmission need to consider the full set of hypotheses a learner could entertain and all of

  1. Myiasis in Dogs in the Greater Accra Region of Ghana.

    PubMed

    Johnson, Sherry A M; Gakuya, Daniel W; Mbuthia, Paul G; Mande, John D; Afakye, Kofi; Maingi, Ndichu

    2016-01-01

    Myiasis is the infestation of tissues of live vertebrate animals and humans with dipterous larvae. In sub-Saharan Africa, Cordylobia anthropohaga and Cordylobia rodhaini are known to be responsible for cutaneous myiasis in animals and humans. Human cases of myiasis, purportedly acquired in Ghana but diagnosed in other countries, have been reported; however, published data on its occurrence in animals in Ghana is unavailable. This study assessed the prevalence of canine myiasis among owned dogs in the Greater Accra region (GAR) of Ghana. A cross-sectional study was conducted in the Greater Accra region of Ghana, selected for being the region with the highest estimated population density of owned dogs. Physical examination and demographic characteristics of the study dogs were assessed. Management of the dogs was assessed through a questionnaire administered to the dog owners. A total of 392 owned dogs were sampled. Twenty-nine (7.4%) had cutaneous myiasis caused by C. rodhaini. In addition, one (0.2%) of the dogs had intestinal myiasis, with Dermatobia hominis as the offending larvae. Among the breeds of dogs with myiasis, the mongrel was most affected, with 24 (82.8%) out of the 29 cases. The mongrels, majority of which (24; 82.8%) were males, were left to roam freely in the community. Results from this study demonstrate that C. rodhaini and D. hominis are important causes of myiasis in owned dogs in the GAR of Ghana. Dogs could play a role in the spread of myiasis to humans, with its attendant public health implications.

  2. Effects of neck bands on survival of greater snow geese

    USGS Publications Warehouse

    Menu, S.; Hestbeck, J.B.; Gauthier, G.; Reed, A.

    2000-01-01

    Neck bands are a widely used marker in goose research. However, few studies have investigated a possible negative effect of this marker on survival. We tested the effect of neck bands on the survival of adult female greater snow geese (Chen caerulescens atlantica) by marking birds with either a neck band and a metal leg band or a leg band only on Bylot Island (Nunavut, formerly included in the Northwest Territories, Canada) from 1990 to 1996. Annual survival was estimated using leg-band recoveries in fall and winter and using neck-band sightings in spring and fall. Recapture rates were estimated using summer recaptures. Using recovery data, the selected model yielded a survival similar for the neck-banded and leg-banded only birds (S = 0.845 ?? 0.070 vs. S = 0.811 ?? 0.107). The hypothesis of equality of survival between the 2 groups was easily accepted under most constraints imposed on survival or recovery rates. However, failure to account for a different direct recovery rate for neck-banded birds would lead us to incorrectly conclude a possible negative effect of neck bands on survival. Using sighting data, mean annual survival of neck-banded birds was independently estimated at 0.833 ?? 0.057, a value very similar to that estimated with band-recovery analysis. Raw recapture rates during summer were significantly lower for neck-banded birds compared to those marked with leg bands only (4.6% vs. 12.1%), but in this analysis, survival, site fidelity, reproductive status, and recapture rates were confounded. We conclude that neck bands did not affect survival of greater snow geese, but could possibly affect other demographic traits such as breeding propensity and emigration.

  3. Black breast cancer survivors experience greater upper extremity disability.

    PubMed

    Dean, Lorraine T; DeMichele, Angela; LeBlanc, Mously; Stephens-Shields, Alisa; Li, Susan Q; Colameco, Chris; Coursey, Morgan; Mao, Jun J

    2015-11-01

    Over one-third of breast cancer survivors experience upper extremity disability. Black women present with factors associated with greater upper extremity disability, including: increased body mass index (BMI), more advanced disease stage at diagnosis, and varying treatment type compared with Whites. No prior research has evaluated the relationship between race and upper extremity disability using validated tools and controlling for these factors. Data were drawn from a survey study among 610 women with stage I-III hormone receptor positive breast cancer. The disabilities of the arm, shoulder and hand (QuickDASH) is an 11-item self-administered questionnaire that has been validated for breast cancer survivors to assess global upper extremity function over the past 7 days. Linear regression and mediation analysis estimated the relationships between race, BMI and QuickDASH score, adjusting for demographics and treatment types. Black women (n = 98) had 7.3 points higher average QuickDASH scores than White (n = 512) women (p < 0.001). After adjusting for BMI, age, education, cancer treatment, months since diagnosis, and aromatase inhibitor status, Black women had an average 4-point (95 % confidence interval 0.18-8.01) higher QuickDASH score (p = 0.04) than White women. Mediation analysis suggested that BMI attenuated the association between race and disability by 40 %. Even several years post-treatment, Black breast cancer survivors had greater upper extremity disability, which was partially mediated by higher BMIs. Close monitoring of high BMI Black women may be an important step in reducing disparities in cancer survivorship. More research is needed on the relationship between race, BMI, and upper extremity disability.

  4. Key Skills Influencing Student Achievement

    ERIC Educational Resources Information Center

    Balch, Tonya; Gruenert, Steve

    2009-01-01

    A predictive, non-experimental, cross-sectional design (Johnson, 2001) was used to conduct a study to determine if elementary administrators' key counseling skills and select demographics predicted state-level student performance indicators in their respective schools. A secondary purpose of this study was to develop a valid and reliable on-line…

  5. 76 FR 58101 - Electric Reliability Organization Interpretation of Transmission Operations Reliability Standard

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-20

    ... of Reliability Standard, TOP-001-1, Requirement R8, which pertains to the restoration of real and... Requirement R8 in Commission-approved NERC Reliability Standard TOP-001-1-- Reliability Responsibilities and... 107 Reliability Standards filed by NERC, including Reliability Standard TOP-001-1.\\4\\ \\2\\...

  6. Decision theory in structural reliability

    NASA Technical Reports Server (NTRS)

    Thomas, J. M.; Hanagud, S.; Hawk, J. D.

    1975-01-01

    Some fundamentals of reliability analysis as applicable to aerospace structures are reviewed, and the concept of a test option is introduced. A decision methodology, based on statistical decision theory, is developed for determining the most cost-effective design factor and method of testing for a given structural assembly. The method is applied to several Saturn V and Space Shuttle structural assemblies as examples. It is observed that the cost and weight features of the design have a significant effect on the optimum decision.

  7. High rate, high reliability Li/SO2 cells

    NASA Astrophysics Data System (ADS)

    Chireau, R.

    1982-03-01

    The use of the lithium/sulfur dioxide system for aerospace applications is discussed. The high rate density in the system is compared to some primary systems: mercury zinc, silver zinc, and magnesium oxide. Estimates are provided of the storage life and shelf life of typical lithium sulfur batteries. The design of lithium cells is presented and criteria are given for improving the output of cells in order to achieve high rate and high reliability.

  8. American lifelines alliance efforts to improve electric power transmission reliability

    USGS Publications Warehouse

    Nishenko, S.P.; Savage, W.U.; Honegger, D.G.; McLane, T.R.; ,

    2002-01-01

    A study was performed on American Lifelines Alliance (ALA) efforts to improve electric power transmission reliability. ALA is a public-private partnership project, with the goal of reducing risks to lifelines from natural hazards and human threat events. The mechanism used by ALA for developing national guidelines for lifeline systems is dependent upon using existing Standards Developing Organizations (SDO) accredited by the American National Standards Institute (ANSI) as means to achieve national consensus.

  9. Reliability-Based Performance Assessment of Damaged Ships

    DTIC Science & Technology

    2006-10-01

    SNAME, Arlington Virginia, II.B. 1-mII.B. 19, 1991. Wang , Ge; Chen, Yongjun ; Zhang, Hanqing; Peng, Hua. (2002). "Longitudinal strength of ships with...strength of hull girders of damaged ships. Reliability of the ship was also estimated by a first order and second moment method. Wang , et al (2002...to achieve a safe design. Wang (1996) have applied several methods, such as point- crossing method, load coincidence method, Ferry Borges method, peak

  10. Probabilistic fatigue methodology and wind turbine reliability

    SciTech Connect

    Lange, C.H.

    1996-05-01

    Wind turbines subjected to highly irregular loadings due to wind, gravity, and gyroscopic effects are especially vulnerable to fatigue damage. The objective of this study is to develop and illustrate methods for the probabilistic analysis and design of fatigue-sensitive wind turbine components. A computer program (CYCLES) that estimates fatigue reliability of structural and mechanical components has been developed. A FORM/SORM analysis is used to compute failure probabilities and importance factors of the random variables. The limit state equation includes uncertainty in environmental loading, gross structural response, and local fatigue properties. Several techniques are shown to better study fatigue loads data. Common one-parameter models, such as the Rayleigh and exponential models are shown to produce dramatically different estimates of load distributions and fatigue damage. Improved fits may be achieved with the two-parameter Weibull model. High b values require better modeling of relatively large stress ranges; this is effectively done by matching at least two moments (Weibull) and better by matching still higher moments. For this purpose, a new, four-moment {open_quotes}generalized Weibull{close_quotes} model is introduced. Load and resistance factor design (LRFD) methodology for design against fatigue is proposed and demonstrated using data from two horizontal-axis wind turbines. To estimate fatigue damage, wind turbine blade loads have been represented by their first three statistical moments across a range of wind conditions. Based on the moments {mu}{sub 1}{hor_ellipsis}{mu}{sub 3}, new {open_quotes}quadratic Weibull{close_quotes} load distribution models are introduced. The fatigue reliability is found to be notably affected by the choice of load distribution model.

  11. High reliability megawatt transformer/rectifier

    NASA Technical Reports Server (NTRS)

    Zwass, Samuel; Ashe, Harry; Peters, John W.

    1991-01-01

    The goal of the two phase program is to develop the technology and design and fabricate ultralightweight high reliability DC to DC converters for space power applications. The converters will operate from a 5000 V dc source and deliver 1 MW of power at 100 kV dc. The power weight density goal is 0.1 kg/kW. The cycle to cycle voltage stability goals was + or - 1 percent RMS. The converter is to operate at an ambient temperature of -40 C with 16 minute power pulses and one hour off time. The uniqueness of the design in Phase 1 resided in the dc switching array which operates the converter at 20 kHz using Hollotron plasma switches along with a specially designed low loss, low leakage inductance and a light weight high voltage transformer. This approach reduced considerably the number of components in the converter thereby increasing the system reliability. To achieve an optimum transformer for this application, the design uses four 25 kV secondary windings to produce the 100 kV dc output, thus reducing the transformer leakage inductance, and the ac voltage stresses. A specially designed insulation system improves the high voltage dielectric withstanding ability and reduces the insulation path thickness thereby reducing the component weight. Tradeoff studies and tests conducted on scaled-down model circuits and using representative coil insulation paths have verified the calculated transformer wave shape parameters and the insulation system safety. In Phase 1 of the program a converter design approach was developed and a preliminary transformer design was completed. A fault control circuit was designed and a thermal profile of the converter was also developed.

  12. EDUCATIONAL ACHIEVEMENT AND THE NAVAJO.

    ERIC Educational Resources Information Center

    HAAS, JOHN; MELVILLE, ROBERT

    A STUDY WAS DEVISED TO APPRAISE THE ACADEMIC ACHIEVEMENT OF NAVAJO STUDENTS LIVING IN DORMITORIES AWAY FROM THE INDIAN RESERVATION. THE FOLLOWING SEVEN FACTORS WERE CHOSEN TO BE INVESTIGATED AS BEING DIRECTLY RELATED TO ACHIEVEMENT--(1) INTELLIGENCE, (2) READING ABILITY, (3) ANXIETY, (4) SELF-CONCEPT, (5) MOTIVATION, (6) VERBAL DEVELOPMENT, (7)…

  13. Sociocultural Origins of Achievement Motivation

    ERIC Educational Resources Information Center

    Maehr, Martin L.

    1977-01-01

    Presents a theoretical review of work on sociocultural influences on achievement, focusing on a critical evaluation of the work of David McClellan. Offers an alternative conception of achievement motivation which stresses the role of contextual and situational factors in addition to personality factors. Available from: Transaction Periodicals…

  14. Raising Boys' Achievement in Schools.

    ERIC Educational Resources Information Center

    Bleach, Kevan, Ed.

    This book offers insights into the range of strategies and good practice being used to raise the achievement of boys. Case studies by school-based practitioners suggest ideas and measures to address the issue of achievement by boys. The contributions are: (1) "Why the Likely Lads Lag Behind" (Kevan Bleach); (2) "Helping Boys Do…

  15. Teaching the Low Level Achiever.

    ERIC Educational Resources Information Center

    Salomone, Ronald E., Ed.

    1986-01-01

    Intended for teachers of the English language arts, the articles in this issue offer suggestions and techniques for teaching the low level achiever. Titles and authors of the articles are as follows: (1) "A Point to Ponder" (Rachel Martin); (2) "Tracking: A Self-Fulfilling Prophecy of Failure for the Low Level Achiever" (James Christopher Davis);…

  16. Early Intervention and Student Achievement

    ERIC Educational Resources Information Center

    Hormes, Mridula T.

    2009-01-01

    The United States Department of Education has been rigorous in holding all states accountable with regard to student achievement. The No Child Left Behind Act of 2001 clearly laid out federal mandates for all schools to follow. K-12 leaders of public schools are very aware of the fact that results in terms of student achievement need to improve…

  17. Parental Involvement and Academic Achievement

    ERIC Educational Resources Information Center

    Goodwin, Sarah Christine

    2015-01-01

    This research study examined the correlation between student achievement and parent's perceptions of their involvement in their child's schooling. Parent participants completed the Parent Involvement Project Parent Questionnaire. Results slightly indicated parents of students with higher level of achievement perceived less demand or invitations…

  18. Asperger Syndrome and Academic Achievement.

    ERIC Educational Resources Information Center

    Griswold, Deborah E.; Barnhill, Gena P.; Myles, Brenda Smith; Hagiwara, Taku; Simpson, Richard L.

    2002-01-01

    A study focused on identifying the academic characteristics of 21 children and youth who have Asperger syndrome. Students had an extraordinary range of academic achievement scores, extending from significantly above average to far below grade level. Lowest achievement scores were shown for numerical operations, listening comprehension, and written…

  19. Perils of Standardized Achievement Testing

    ERIC Educational Resources Information Center

    Haladyna, Thomas M.

    2006-01-01

    This article argues that the validity of standardized achievement test-score interpretation and use is problematic; consequently, confidence and trust in such test scores may often be unwarranted. The problem is particularly severe in high-stakes situations. This essay provides a context for understanding standardized achievement testing, then…

  20. Stress Correlates and Academic Achievement.

    ERIC Educational Resources Information Center

    Bentley, Donna Anderson; And Others

    An ongoing concern for educators is the identification of factors that contribute to or are associated with academic achievement; one such group of variables that has received little attention are those involving stress. The relationship between perceived sources of stress and academic achievement was examined to determine if reactions to stress…

  1. School Size and Student Achievement

    ERIC Educational Resources Information Center

    Riggen, Vicki

    2013-01-01

    This study examined whether a relationship between high school size and student achievement exists in Illinois public high schools in reading and math, as measured by the Prairie State Achievement Exam (PSAE), which is administered to all Illinois 11th-grade students. This study also examined whether the factors of socioeconomic status, English…

  2. Reliability of the special support system for sitting pressure redistribution

    PubMed Central

    Lee, Sang-Heon

    2016-01-01

    [Purpose] This study investigated the reliability of the Special Support System. [Subjects and Methods] Eighteen female and 14 male volunteers participated in this study. Participants were asked to sit on the Special Support System with their chins tucked in, spines straight, pelvis neutrally positioned, and their hands placed on their thighs. They were also asked to flex their hips, knees, and ankles to approximately 90 degrees and to put their feet flat on the floor. The total contact area, mean total pressure, as well as mean and peak pressures of each quadrant were each measured 15 times. Test-retest reliability was analyzed for inflated air pressure, and pressure redistribution values by using intraclass correlation coefficients. [Results] The intraclass correlation coefficient was greater than 0.89 for inflated air pressure and greater than 0.92 for total contact area, mean total pressure, and each quadrant’s mean and peak pressure. [Conclusion] The findings suggest that the Special Support System is reliable and can be used as an alternative method for redistributing sitting pressure. PMID:28174458

  3. Reliability of Visual and Somatosensory Feedback in Skilled Movement: The Role of the Cerebellum.

    PubMed

    Mizelle, J C; Oparah, Alexis; Wheaton, Lewis A

    2016-01-01

    The integration of vision and somatosensation is required to allow for accurate motor behavior. While both sensory systems contribute to an understanding of the state of the body through continuous updating and estimation, how the brain processes unreliable sensory information remains to be fully understood in the context of complex action. Using functional brain imaging, we sought to understand the role of the cerebellum in weighting visual and somatosensory feedback by selectively reducing the reliability of each sense individually during a tool use task. We broadly hypothesized upregulated activation of the sensorimotor and cerebellar areas during movement with reduced visual reliability, and upregulated activation of occipital brain areas during movement with reduced somatosensory reliability. As specifically compared to reduced somatosensory reliability, we expected greater activations of ipsilateral sensorimotor cerebellum for intact visual and somatosensory reliability. Further, we expected that ipsilateral posterior cognitive cerebellum would be affected with reduced visual reliability. We observed that reduced visual reliability results in a trend towards the relative consolidation of sensorimotor activation and an expansion of cerebellar activation. In contrast, reduced somatosensory reliability was characterized by the absence of cerebellar activations and a trend towards the increase of right frontal, left parietofrontal activation, and temporo-occipital areas. Our findings highlight the role of the cerebellum for specific aspects of skillful motor performance. This has relevance to understanding basic aspects of brain functions underlying sensorimotor integration, and provides a greater understanding of cerebellar function in tool use motor control.

  4. Reliability Considerations for Composite Overwrapped Pressure Vessels on Spacecraft

    NASA Technical Reports Server (NTRS)

    Murthy, Pappu L. N.; Gyekenyesi, John P.; Grimes-Ledesma, Lorie; Phoenix, S. L.

    2007-01-01

    Composite Overwrapped Pressure Vessels (COPVs) are used to store gases under high pressure onboard spacecraft. These are used for a variety of purposes such as propelling liquid fuel etc, Kevlar, glass, Carbon and other more recent fibers have all been in use to overwrap the vessels. COPVs usually have a thin metallic liner with the primary purpose of containing the gases and prevent any leakage. The liner is overwrapped with filament wound composite such as Kevlar, Carbon or Glass fiber. Although the liner is required to perform in the leak before break mode making the failure a relatively benign mode, the overwrap can fail catastrophically under sustained load due to stress rupture. It is this failure mode that is of major concern as the stored energy of such vessels is often great enough ta cause loss of crew and vehicle. The present paper addresses some of the reliability concerns associated specifically with Kevlar Composite Overwrapped Pressure Vessels. The primary focus of the paper is on how reliability of COPV's are established for the purpose of deciding in general their flight worthiness and continued use. Analytical models based on existing design data will be presented showing how to achieve the required reliability metric to the end of a specific period of performance. Uncertainties in the design parameters and how they affect reliability and confidence intervals will be addressed as well. Some trade studies showing how reliability changes with time during a program period will be presented.

  5. Is entheses ultrasound reliable? A reading Latin American exercise.

    PubMed

    Ventura-Ríos, L; Navarro-Compan, V; Aliste, M; Linares, M Alva; Areny, R; Audisio, M; Bertoli, A M; Cazenave, T; Cerón, C; Díaz, M E; Gutiérrez, M; Hernández, C; Navarta, D A; Pineda, C; Py, G E; Reginato, A M; Rosa, J; Saaibi, D L; Sedano, O; Solano, C; Castillo-Gallego, C; Falçao, S; De Miguel, E

    2016-05-01

    The objective of this study is to evaluate inter-reader entheses ultrasound (US) reliability and the influence of the type of image or degree of sonographer experience on US reliability in patients with spondyloarthritis (SpA). Eighteen Latin American ultrasonographers with different experience took part in an US reading exercise evaluating 60 entheseal images (50 % static images and 50 % videos) from healthy controls and SpA patients. The following sonographic lesions were assessed: structure, thickness, bone proliferation/tendon calcification, erosions, bursitis, and Doppler signal. Another group of three experts with significant experience in entheses US read all images too. Inter-reader reliability among participants and experts was calculated by the Cohen's kappa coefficient. Thresholds for kappa values were <0.2 poor, 0.21-0.4 fair, 0.41-0.6 moderate, 0.61-0.8 good, and 0.81-1 excellent. Furthermore, the results for the expert group were stratified based on the type of image. Kappa correlation coefficients among participants, showed variability depending on the type of lesion, being fair for structure and thickness, moderate for calcifications, erosions, and bursitis, and excellent for Doppler signal. Inter-reader reliability among experts was higher, being moderate for structure and thickness, good for calcifications and bursitis, and excellent for erosions and Doppler. Inter-reader reliability for assessing calcification and structure using static images was significantly higher than for videos. Overall inter-reader reliability for assessing entheses by US in SpA is moderate to excellent for most of the lesions. However, special training seems fundamental to achieve better inter-reader reliability. Moreover, the type of image influenced these results, where evaluation of entheses by videos was more difficult than by static images.

  6. Designing for Reliability and Robustness

    NASA Technical Reports Server (NTRS)

    Svetlik, Randall G.; Moore, Cherice; Williams, Antony

    2017-01-01

    Long duration spaceflight has a negative effect on the human body, and exercise countermeasures are used on-board the International Space Station (ISS) to minimize bone and muscle loss, combatting these effects. Given the importance of these hardware systems to the health of the crew, this equipment must continue to be readily available. Designing spaceflight exercise hardware to meet high reliability and availability standards has proven to be challenging throughout the time the crewmembers have been living on ISS beginning in 2000. Furthermore, restoring operational capability after a failure is clearly time-critical, but can be problematic given the challenges of troubleshooting the problem from 220 miles away. Several best-practices have been leveraged in seeking to maximize availability of these exercise systems, including designing for robustness, implementing diagnostic instrumentation, relying on user feedback, and providing ample maintenance and sparing. These factors have enhanced the reliability of hardware systems, and therefore have contributed to keeping the crewmembers healthy upon return to Earth. This paper will review the failure history for three spaceflight exercise countermeasure systems identifying lessons learned that can help improve future systems. Specifically, the Treadmill with Vibration Isolation and Stabilization System (TVIS), Cycle Ergometer with Vibration Isolation and Stabilization System (CEVIS), and the Advanced Resistive Exercise Device (ARED) will be reviewed, analyzed, and conclusions identified so as to provide guidance for improving future exercise hardware designs. These lessons learned, paired with thorough testing, offer a path towards reduced system down-time.

  7. Reliability of steam generator tubing

    SciTech Connect

    Kadokami, E.

    1997-02-01

    The author presents results on studies made of the reliability of steam generator (SG) tubing. The basis for this work is that in Japan the issue of defects in SG tubing is addressed by the approach that any detected defect should be repaired, either by plugging the tube or sleeving it. However, this leaves open the issue that there is a detection limit in practice, and what is the effect of nondetectable cracks on the performance of tubing. These studies were commissioned to look at the safety issues involved in degraded SG tubing. The program has looked at a number of different issues. First was an assessment of the penetration and opening behavior of tube flaws due to internal pressure in the tubing. They have studied: penetration behavior of the tube flaws; primary water leakage from through-wall flaws; opening behavior of through-wall flaws. In addition they have looked at the question of the reliability of tubing with flaws during normal plant operation. Also there have been studies done on the consequences of tube rupture accidents on the integrity of neighboring tubes.

  8. A new probabilistic seismic hazard assessment for greater Tokyo

    USGS Publications Warehouse

    Stein, R.S.; Toda, S.; Parsons, T.; Grunewald, E.; Blong, R.; Sparks, S.; Shah, H.; Kennedy, J.

    2006-01-01

    Tokyo and its outlying cities are home to one-quarter of Japan's 127 million people. Highly destructive earthquakes struck the capital in 1703, 1855 and 1923, the last of which took 105 000 lives. Fuelled by greater Tokyo's rich seismological record, but challenged by its magnificent complexity, our joint Japanese-US group carried out a new study of the capital's earthquake hazards. We used the prehistoric record of great earthquakes preserved by uplifted marine terraces and tsunami deposits (17 M???8 shocks in the past 7000 years), a newly digitized dataset of historical shaking (10 000 observations in the past 400 years), the dense modern seismic network (300 000 earthquakes in the past 30 years), and Japan's GeoNet array (150 GPS vectors in the past 10 years) to reinterpret the tectonic structure, identify active faults and their slip rates and estimate their earthquake frequency. We propose that a dislodged fragment of the Pacific plate is jammed between the Pacific, Philippine Sea and Eurasian plates beneath the Kanto plain on which Tokyo sits. We suggest that the Kanto fragment controls much of Tokyo's seismic behaviour for large earthquakes, including the damaging 1855 M???7.3 Ansei-Edo shock. On the basis of the frequency of earthquakes beneath greater Tokyo, events with magnitude and location similar to the M??? 7.3 Ansei-Edo event have a ca 20% likelihood in an average 30 year period. In contrast, our renewal (time-dependent) probability for the great M??? 7.9 plate boundary shocks such as struck in 1923 and 1703 is 0.5% for the next 30 years, with a time-averaged 30 year probability of ca 10%. The resulting net likelihood for severe shaking (ca 0.9g peak ground acceleration (PGA)) in Tokyo, Kawasaki and Yokohama for the next 30 years is ca 30%. The long historical record in Kanto also affords a rare opportunity to calculate the probability of shaking in an alternative manner exclusively from intensity observations. This approach permits robust estimates

  9. Experience-dependent natal philopatry of breeding greater flamingos.

    PubMed

    Balkiz, Ozge; Béchet, Arnaud; Rouan, Lauriane; Choquet, Rémi; Germain, Christophe; Amat, Juan A; Rendón-Martos, Manuel; Baccetti, Nicola; Nissardi, Sergio; Ozesmi, Uygar; Pradel, Roger

    2010-09-01

    1. Contrary to the generally high level of natal philopatry (i.e. likelihood that individuals breed at their natal colony) found in first-breeding colonial birds, little is known of natal philopatry later in life. Most hypotheses advanced to explain natal philopatry are valid at all ages. However, for young and inexperienced birds, the benefits of natal philopatry may be counterbalanced by the costs of intraspecific competition at the natal colony making dispersal temporarily advantageous. In turn, experience may increase competitive ability and make natal philopatry advantageous again. 2. We evaluated this hypothesis on the large-scale dispersal of greater flamingos Phoenicopterus roseus breeding among three colonies comprising >85% of the Western Mediterranean metapopulation. The Camargue (France) and Fuente de Piedra (Spain) are large and saturated colonies while Molentargius (Sardinia) is a recent and growing colony. 3. We used a 20-year capture-mark-resighting dataset of 4900 flamingos ringed as chicks in Camargue and Fuente de Piedra and breeding at the three colonies. We assessed the effects of natal colony and breeding experience (first-time observed breeders versus confirmed experienced breeders) on dispersal using multistate capture-recapture models. Dispersal to an unobservable state accounted for temporary emigration. 4. Fidelity was higher at the natal colony (>84%) than elsewhere. Fidelity increased with experience in the two large colonies (Camargue and Fuente de Piedra) suggesting a large-scale experience-related despotic distribution. Breeding dispersal was significant (up to 61% and 52% for first-time breeders and experienced breeders, respectively) so that colony dynamics is affected by exchanges with other colonies. Except for Fuente-born breeders leaving Molentargius, dispersal to the natal colony was higher than to any other colonies. 5. Survival was not higher at the natal colony. Inexperienced birds likely had lower breeding success at the

  10. Greater Trochanteric Pain Syndrome: Epidemiology and Associated Factors

    PubMed Central

    Segal, Neil A.; Felson, David T.; Torner, James C.; Zhu, Yanyan; Curtis, Jeffrey R.; Niu, Jingbo; Nevitt, Michael C.

    2010-01-01

    Objectives To describe the prevalence of greater trochanteric pain syndrome (GTPS); to determine whether GTPS is associated with iliotibial band (ITB) tenderness, knee osteoarthritis (OA), body mass index (BMI), or low back pain (LBP); and to assess whether GTPS is associated with reduced hip internal rotation, physical activity, and mobility. Design Cross-sectional, population-based study. Setting Multicenter observational study. Participants Community-dwelling adults (N=3026) ages 50 to 79 years. Interventions Not applicable. Main Outcome Measures Greater trochanteric tenderness to palpation in subjects with complaints of hip pain and no signs of hip OA or generalized myofascial tenderness. Results The prevalence of unilateral and bilateral GTPS was 15.0% and 8.5% in women and 6.6% and 1.9% men. Odds ratio (OR) for women was 3.37 (95% confidence interval [CI], 2.67–4.25), but age and race were not significantly associated with GTPS. In a multivariate model, adjusting for age, sex, ITB tenderness, ipsilateral and contralateral knee OA, BMI, and LBP, ITB tenderness (OR=1.72; 95% CI, 1.34–2.19), knee OA ipsilaterally (OR=3.47; 95% CI, 2.72–4.42) and con-tralaterally (OR=1.74; 95% CI, 1.32–2.28), and LBP (OR=2.79; 95% CI, 2.22–3.50) were positively related to GTPS. In this complete model, BMI was not associated with GTPS (OR=1.10; 95% CI, 0.80–1.52 when comparing ≥ 30 with <25kg/m2). Hip internal rotation range of motion did not differ based on GTPS status. After multivariate adjustment, GTPS did not alter physical activity score, but bilateal GTPS was significantly associated with a higher 20-meter walk time and chair stand time. Conclusions The higher prevalence of GTPS in women and in adults with ITB pain or knee OA indicates that altered lower-limb biomechanics may be related to GTPS. Slower functional performance in those with GTPS suggests that the study of targeted rehabilitation may be useful. A longitudinal study will be necessary to identify

  11. The Effects of Integrated Transformational Leadership on Achievement

    ERIC Educational Resources Information Center

    Boberg, John Eric; Bourgeois, Steven J.

    2016-01-01

    Purpose: Greater understanding about how variables mediate the relationship between leadership and achievement is essential to the success of reform efforts that hold leaders accountable for student learning. The purpose of this paper is to test a model of integrated transformational leadership including three important school mediators.…

  12. Academic Effort and Achievement in Science: Beyond a Gendered Relationship

    ERIC Educational Resources Information Center

    Adamuti-Trache, Maria; Sweet, Robert

    2013-01-01

    This study employs the 2004 School Achievement Indicators Program (SAIP) data to examine whether academic effort manifested by greater investments in school and homework does result in higher literacy scores in science for Canadian students. The study compares four gender-immigrant profiles: Canadian-born males, immigrant males, Canadian-born…

  13. Electronic Play, Study, Communication, and Adolescent Achievement, 2003-2008

    ERIC Educational Resources Information Center

    Hofferth, Sandra L.; Moon, Ui Jeong

    2012-01-01

    Adolescents' time spent messaging, exploring websites, and studying on the computer increased between 2003 and 2008. Using data from the Panel Study of Income Dynamics Child Development Supplement, this study examines how such changes have influenced individual achievement and behavior from childhood to adolescence. Greater communications and…

  14. Comparison of Achievement of Students in High School Courses

    ERIC Educational Resources Information Center

    Troxel, Verne A.

    1970-01-01

    Compares student achievements on common objectives of CHEMS, CBA, and "Modern Chemistry high school chemistry courses. Results indicate the three couses are not equally effective in meeting their objectives. CHEMS and CBA develop a better understanding of chemistry and science, as well as develop greater ability for critical thinking. CBA…

  15. Achieving Equity in Higher Education: The Unfinished Agenda

    ERIC Educational Resources Information Center

    Astin, Alexander W.; Astin, Helen S.

    2015-01-01

    In this retrospective account of their scholarly work over the past 45 years, Alexander and Helen Astin show how the struggle to achieve greater equity in American higher education is intimately connected to issues of character development, leadership, civic responsibility, and spirituality. While shedding some light on a variety of questions…

  16. Social, Cultural, and Contextual Influences on Achievement Motivation Behavior.

    ERIC Educational Resources Information Center

    Maehr, Martin L.

    Given the decline in birth rates, which will produce a steep decline in the youth population by 1990, this paper examines the possible effects such a population shift will have on the achievement motivation of children. It is reasoned the increased adult/child ratio could result in either of two possibilities: the greater attention paid to the…

  17. The Achiever. Volume 6, Number 8, November-December 2007

    ERIC Educational Resources Information Center

    Ashby, Nicole, Ed.

    2007-01-01

    "The Achiever" is a monthly publication for parents and community leaders. Each issue contains news and information about school improvement in the United States. Highlights of this issue include: (1) President Signs College Cost Reduction Act; (2) Galvanizing the Community: Charter Schools Provides Greater Choice to Colorado Latinos…

  18. Effective Teachers = Student Achievement: What the Research Says

    ERIC Educational Resources Information Center

    Stronge, James H.

    2010-01-01

    Research has shown that there is no greater influence on a student's success than the quality of his or her teacher. This book presents the research findings which demonstrate the connection between teacher effectiveness and student achievement. We've always known, at least intuitively, that teachers matter, but this book proves that teachers are…

  19. The Longitudinal Link between Student Health and Math Achievement Scores

    ERIC Educational Resources Information Center

    Garcy, Anthony M.

    2009-01-01

    This study investigated the relationship between health conditions suffered over time and student scores on the Stanford Achievement Test 9 in Yuma County, Arizona, public grade schools. The majority of children in Yuma County were of Hispanic origin. The poverty and low income status of most of these children placed them at greater risk for…

  20. 75 FR 71613 - Mandatory Reliability Standards for Interconnection Reliability Operating Limits

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-24

    ... Energy Regulatory Commission 18 CFR Part 40 Mandatory Reliability Standards for Interconnection Reliability Operating Limits November 18, 2010. AGENCY: Federal Energy Regulatory Commission. ACTION: Notice... Regulatory Commission proposes to approve three new Interconnection Reliability Operations and...

  1. Concurrent Alcohol Dependence Among Methadone-Maintained Cocaine Abusers Is Associated with Greater Abstinence

    PubMed Central

    Byrne, Shannon A.; Petry, Nancy M.

    2011-01-01

    Concurrent alcohol dependence (AD) among polysubstance abusers has been associated with negative consequences, although it may not necessarily lead to poor treatment outcomes. One of the most efficacious treatments for cocaine abuse is contingency management (CM), but little research has explored the impact of AD on abstinence outcomes, particularly among patients in methadone maintenance. Using data from three trials of CM for cocaine use, we compared baseline characteristics and post-treatment and follow-up cocaine outcomes between methadone maintained, cocaine dependent patients (N=193) with and without concurrent AD, randomized to standard care (SC) with or without CM. Patients with and without concurrent AD had similar baseline characteristics, with the exception that AD patients reported more alcohol use. AD patients achieved longer durations of cocaine abstinence and were more likely to submit a cocaine negative sample at follow-up than non-AD patients. Patients randomized to CM achieved better outcomes than those randomized to SC, but there was no interaction between treatment condition and AD status. These findings suggest that cocaine using methadone patients with AD achieve greater cocaine abstinence than their non-AD counterparts and should not be necessarily viewed as more difficult to treat. PMID:21463068

  2. Importance, reliability and usefulness of acceleration measures in team sports.

    PubMed

    Delaney, Jace A; Cummins, Cloe J; Thornton, Heidi R; Duthie, Grant M

    2017-02-08

    The ability to accelerate, decelerate and change direction efficiently is imperative to successful team-sports performance. Traditional intensity-based thresholds for acceleration and deceleration may be inappropriate for time-series data, and have been shown to exhibit poor reliability, suggesting other techniques may be preferable. This study assessed movement data from one professional rugby league team throughout two full seasons and one pre-season period. Using both 5 Hz and 10 Hz global positioning systems (GPS) units, a range of acceleration-based variables were evaluated for their inter-unit reliability, ability to discriminate between positions, and associations with perceived muscle soreness. The reliability of 5 Hz GPS for measuring acceleration and deceleration ranged from good to poor (CV = 3.7-27.1%), with the exception of high-intensity deceleration efforts (CV = 11.1-11.8%), the 10 Hz units exhibited moderate to good inter-unit reliability (CV = 1.2-6.9%). Reliability of average metrics (average acceleration/deceleration, average acceleration and average deceleration) ranged from good to moderate (CV = 1.2-6.5%). Substantial differences were detected between positions using time spent accelerating and decelerating for all magnitudes, but these differences were less clear when considering the count or distance above acceleration/deceleration thresholds. All average metrics detected substantial differences between positions. All measures were similarly related to perceived muscle soreness, with the exception of high-intensity acceleration and deceleration counts. This study has proposed that averaging the acceleration/deceleration demands over an activity may be a more appropriate method compared to threshold-based methods, due to a greater reliability between units, whilst not sacrificing sensitivity to within and between-subject changes.

  3. Greater transportation energy and GHG offsets from bioelectricity than ethanol.

    PubMed

    Campbell, J E; Lobell, D B; Field, C B

    2009-05-22

    The quantity of land available to grow biofuel crops without affecting food prices or greenhouse gas (GHG) emissions from land conversion is limited. Therefore, bioenergy should maximize land-use efficiency when addressing transportation and climate change goals. Biomass could power either internal combustion or electric vehicles, but the relative land-use efficiency of these two energy pathways is not well quantified. Here, we show that bioelectricity outperforms ethanol across a range of feedstocks, conversion technologies, and vehicle classes. Bioelectricity produces an average of 81% more transportation kilometers and 108% more emissions offsets per unit area of cropland than does cellulosic ethanol. These results suggest that alternative bioenergy pathways have large differences in how efficiently they use the available land to achieve transportation and climate goals.

  4. Farming Approaches for Greater Biodiversity, Livelihoods, and Food Security.

    PubMed

    Garibaldi, Lucas A; Gemmill-Herren, Barbara; D'Annolfo, Raffaele; Graeub, Benjamin E; Cunningham, Saul A; Breeze, Tom D

    2017-01-01

    Scientists and policy-makers globally are calling for alternative approaches to conventional intensification of agriculture that enhance ecosystem services provided by biodiversity. The evidence reviewed here suggests that alternative approaches can achieve high crop yields and profits, but the performance of other socioeconomic indicators (as well as long-term trends) is surprisingly poorly documented. Consequently, the implementation of conventional intensification and the discussion of alternative approaches are not based on quantitative evidence of their simultaneous ecological and socioeconomic impacts across the globe. To close this knowledge gap, we propose a participatory assessment framework. Given the impacts of conventional intensification on biodiversity loss and greenhouse gas emissions, such evidence is urgently needed to direct science-policy initiatives, such as the United Nations (UN) 2030 Agenda for Sustainable Development.

  5. Multi-Agent System for Resource Reliability

    DTIC Science & Technology

    2007-11-02

    1 research and development of a prototype for network resource reliability has laid the groundwork for the Phase 2 implementation of MASRR, a Multi - Agent System for Resource Reliability, and its eventual commercialization.

  6. Malaria Modeling and Surveillance for the Greater Mekong Subregion

    NASA Technical Reports Server (NTRS)

    Kiang, Richard; Adimi, Farida; Soika, Valerii; Nigro, Joseph

    2005-01-01

    At 4,200 km, the Mekong River is the tenth longest river in the world. It directly and indirectly influences the lives of hundreds of millions of inhabitants in its basin. The riparian countries - Thailand, Myanmar, Cambodia, Laos, Vietnam, and a small part of China - form the Greater Mekong Subregion (GMS). This geographical region has the misfortune of being the world's epicenter of falciparum malaria, which is the most severe form of malaria caused by Plasmodium falciparum. Depending on the country, approximately 50 to 90% of all malaria cases are due to this species. In the Malaria Modeling and Surveillance Project, we have been developing techniques to enhance public health's decision capability for malaria risk assessments and controls. The main objectives are: 1) Identifying the potential breeding sites for major vector species; 2) Implementing a malaria transmission model to identify the key factors that sustain or intensify malaria transmission; and 3) Implementing a risk algorithm to predict the occurrence of malaria and its transmission intensity. The potential benefits are: 1) Increased warning time for public health organizations to respond to malaria outbreaks; 2) Optimized utilization of pesticide and chemoprophylaxis; 3) Reduced likelihood of pesticide and drug resistance; and 4) Reduced damage to environment. Environmental parameters important to malaria transmission include temperature, relative humidity, precipitation, and vegetation conditions. These parameters are extracted from NASA Earth science data sets. Hindcastings based on these environmental parameters have shown good agreement to epidemiological records.

  7. Status on disposal of greater-than-Class C

    SciTech Connect

    Plummer, T.L.

    1995-12-31

    The Department of Energy (DOE) has developed a plan for the management and disposal of commercially generated greater-than-Class C (GTCC) low-level radioactive waste. The Low-Level Radioactive Waste Policy Amendments Act of 1985 made DOE responsible for disposal of GTCC waste. The act requires that GTCC waste be disposed in a Nuclear Regulatory Commission (NRC)-licensed facility. The NRC has amended 10 CFR 61 to express a preference for geologic disposal of GTCC waste. Based on reassessment studies, legislative guidance, and stakeholder involvement, a revised plan has been formulated to provide for total management of GTCC waste. The plan has four major thrusts: (1) plan for GTCC waste storage at the generator site until disposal is available, (2) establish storage for GTCC sealed sources posing health and safety risk to the public, (3) facilitate storage for other GTCC waste posing health and safety risk to the public, and (4) plan for co-disposal of GTCC waste in a geologic disposal site with similar waste types. The revised plan focuses on applying available resources to near- and long-term needs.

  8. Greater-than-Class C low-level waste characterization

    SciTech Connect

    Piscitella, R.R.

    1991-12-31

    In 1985, Public Law 99-240 (Low-Level Radioactive Waste Policy Amendments Act of 1985) made the Department of Energy (DOE) responsible for the disposal of greater-than-Class C low-level radioactive waste (GTCC LLW). DOE strategies for storage and disposal of GTCC LLW required characterization of volumes, radionuclide activities, and waste forms. Data from existing literature, disposal records, and original research were used to estimate characteristics, project volumes, and determine radionuclide activities to the years 2035 and 2055. Twenty-year life extensions for 70% of the operating nuclear reactors were assumed to calculate the GTCC LLW available in 2055. The following categories of GTCC LLW were addressed: Nuclear Utilities Waste; Potential Sealed Sources GTCC LLW; DOE-Held Potential GTCC LLW; and Other Generator Waste. It was determined that the largest volume of these wastes, approximately 57%, is generated by nuclear utilities. The Other Generator Waste category contributes approximately 10% of the total GTCC LLW volume projected to the year 2035. DOE-Held Potential GTCC LLW accounts for nearly 33% of all waste projected to the year 2035. Potential Sealed Sources GTCC LLW is less than 0.2% of the total projected volume. The base case total projected volume of GTCC LLW for all categories was 3,250 cubic meters. This was substantially less than previous estimates.

  9. Galactic Diffuse Gamma Ray Emission Is Greater than 10 Gev

    NASA Technical Reports Server (NTRS)

    Hunter, Stanley D.; White, Nicholas E. (Technical Monitor)

    2000-01-01

    AGILE and Gamma-ray Large Area Telescope (GLAST) are the next high-energy gamma-ray telescopes to be flown in space. These instruments will have angular resolution about 5 times better than Energetic Gamma-Ray Experiment Telescope (EGRET) above 10 GeV and much larger field of view. The on-axis effective area of AGILE will be about half that of EGRET, whereas GLAST will have about 6 times greater effective area than EGRET. The capabilities of ground based very high-energy telescopes are also improving, e.g. Whipple, and new telescopes, e.g. Solar Tower Atmospheric Cerenkov Effect Experiment (STACEE), Cerenkov Low Energy Sampling and Timing Experiment (CELESTE), and Mars Advanced Greenhouse Integrated Complex (MAGIC) are expected to have low-energy thresholds and sensitivities that will overlap the GLAST sensitivity above approximately 10 GeV. In anticipation of the results from these new telescopes, our current understanding of the galactic diffuse gamma-ray emission, including the matter and cosmic ray distributions is reviewed. The outstanding questions are discussed and the potential of future observations with these new instruments to resolve these questions is examined.

  10. Outreach impact study: the case of the Greater Midwest Region*

    PubMed Central

    Huber, Jeffrey T; Kean, Emily B; Fitzgerald, Philip D; Altman, Trina A; Young, Zach G; Dupin, Katherine M; Leskovec, Jacqueline; Holst, Ruth

    2011-01-01

    Objectives: The purpose of the study was to assess the impact that funding from the National Network of Libraries of Medicine (NN/LM), Greater Midwest Region (GMR), has on member institutions' ability to conduct outreach on behalf of NN/LM. Methods: The study employed both content analysis and survey methodologies. The final reports from select GMR-funded outreach projects (n = 20) were analyzed based on a set of evaluation criteria. Project principal investigators (n = 13) were then surveyed using the same evaluation criteria. Results: Results indicated that outreach projects supported by GMR funding improved access to biomedical information for professionals and the general public. Barriers to conducting outreach projects included time constraints or commitments, staffing, scheduling and absenteeism, inadequate space, and issues associated with technology (e.g., hardware and software, Internet connectivity and firewall issues, and creation and use of new technologies). Conclusions: The majority of project principal investigators indicated that their attempts to conduct outreach were successful. Moreover, most noted that outreach had a positive impact on professionals as well as the general public. In general, it seems that negative outcomes, as with most barriers to conducting outreach, can be mitigated by more thorough planning. PMID:22022223

  11. The Shifting Climate Portfolio of the Greater Yellowstone Area

    PubMed Central

    Sepulveda, Adam J.; Tercek, Michael T.; Al-Chokhachy, Robert; Ray, Andrew M.; Thoma, David P.; Hossack, Blake R.; Pederson, Gregory T.; Rodman, Ann W.; Olliff, Tom

    2015-01-01

    Knowledge of climatic variability at small spatial extents (< 50 km) is needed to assess vulnerabilities of biological reserves to climate change. We used empirical and modeled weather station data to test if climate change has increased the synchrony of surface air temperatures among 50 sites within the Greater Yellowstone Area (GYA) of the interior western United States. This important biological reserve is the largest protected area in the Lower 48 states and provides critical habitat for some of the world’s most iconic wildlife. We focused our analyses on temporal shifts and shape changes in the annual distributions of seasonal minimum and maximum air temperatures among valley-bottom and higher elevation sites from 1948–2012. We documented consistent patterns of warming since 1948 at all 50 sites, with the most pronounced changes occurring during the Winter and Summer when minimum and maximum temperature distributions increased. These shifts indicate more hot temperatures and less cold temperatures would be expected across the GYA. Though the shifting statistical distributions indicate warming, little change in the shape of the temperature distributions across sites since 1948 suggest the GYA has maintained a diverse portfolio of temperatures within a year. Spatial heterogeneity in temperatures is likely maintained by the GYA’s physiographic complexity and its large size, which encompasses multiple climate zones that respond differently to synoptic drivers. Having a diverse portfolio of temperatures may help biological reserves spread the extinction risk posed by climate change. PMID:26674185

  12. Distribution of grizzly bears in the Greater Yellowstone Ecosystem, 2004

    USGS Publications Warehouse

    Schwartz, C.C.; Haroldson, M.A.; Gunther, K.; Moody, D.

    2006-01-01

    The US Fish and Wildlife Service (USFWS) proposed delisting the Yellowstone grizzly bear (Ursus arctos horribilis) in November 2005. Part of that process required knowledge of the most current distribution of the species. Here, we update an earlier estimate of occupied range (1990–2000) with data through 2004. We used kernel estimators to develop distribution maps of occupied habitats based on initial sightings of unduplicated females (n = 481) with cubs of the year, locations of radiomarked bears (n = 170), and spatially unique locations of conflicts, confrontations, and mortalities (n = 1,075). Although each data set was constrained by potential sampling bias, together they provided insight into areas in the Greater Yellowstone Ecosystem (GYE) currently occupied by grizzly bears. The current distribution of 37,258 km2 (1990–2004) extends beyond the distribution map generated with data from 1990–2000 (34,416 km2 ). Range expansion is particularly evident in parts of the Caribou–Targhee National Forest in Idaho and north of Spanish Peaks on the Gallatin National Forest in Montana.

  13. Vaccine preventability of meningococcal clone, Greater Aachen Region, Germany.

    PubMed

    Elias, Johannes; Schouls, Leo M; van de Pol, Ingrid; Keijzers, Wendy C; Martin, Diana R; Glennie, Anne; Oster, Philipp; Frosch, Matthias; Vogel, Ulrich; van der Ende, Arie

    2010-03-01

    Emergence of serogroup B meningococci of clonal complex sequence type (ST) 41/44 can cause high levels of disease, as exemplified by a recent epidemic in New Zealand. Multiplication of annual incidence rates (3.1 cases/100,000 population) of meningococcal disease in a defined German region, the city of Aachen and 3 neighboring countries (Greater Aachen) prompted us to investigate and determine the source and nature of this outbreak. Using molecular typing and geographic mapping, we analyzed 1,143 strains belonging to ST41/44 complex, isolated from persons with invasive meningococcal disease over 6 years (2001-2006) from 2 German federal states (total population 26 million) and the Netherlands. A spatially slowly moving clone with multiple-locus variable-number tandem repeat analysis type 19, ST42, and antigenic profile B:P1.7-2,4:F1-5 was responsible for the outbreak. Bactericidal activity in serum samples from the New Zealand MeNZB vaccination campaign confirmed vaccine preventability. Because this globally distributed epidemic strain spreads slowly, vaccination efforts could possibly eliminate meningococcal disease in this area.

  14. The shifting climate portfolio of the Greater Yellowstone Area

    USGS Publications Warehouse

    Sepulveda, Adam; Tercek, Mike T; Al-Chokhachy, Robert K.; Ray, Andrew; Thoma, David P.; Hossack, Blake R.; Pederson, Gregory T.; Rodman, Ann; Olliff, Tom

    2015-01-01

    Knowledge of climatic variability at small spatial extents (< 50 km) is needed to assess vulnerabilities of biological reserves to climate change. We used empirical and modeled weather station data to test if climate change has increased the synchrony of surface air temperatures among 50 sites within the Greater Yellowstone Area (GYA) of the interior western United States. This important biological reserve is the largest protected area in the Lower 48 states and provides critical habitat for some of the world’s most iconic wildlife. We focused our analyses on temporal shifts and shape changes in the annual distributions of seasonal minimum and maximum air temperatures among valley-bottom and higher elevation sites from 1948–2012. We documented consistent patterns of warming since 1948 at all 50 sites, with the most pronounced changes occurring during the Winter and Summer when minimum and maximum temperature distributions increased. These shifts indicate more hot temperatures and less cold temperatures would be expected across the GYA. Though the shifting statistical distributions indicate warming, little change in the shape of the temperature distributions across sites since 1948 suggest the GYA has maintained a diverse portfolio of temperatures within a year. Spatial heterogeneity in temperatures is likely maintained by the GYA’s physiographic complexity and its large size, which encompasses multiple climate zones that respond differently to synoptic drivers. Having a diverse portfolio of temperatures may help biological reserves spread the extinction risk posed by climate change.

  15. The Shifting Climate Portfolio of the Greater Yellowstone Area.

    PubMed

    Sepulveda, Adam J; Tercek, Michael T; Al-Chokhachy, Robert; Ray, Andrew M; Thoma, David P; Hossack, Blake R; Pederson, Gregory T; Rodman, Ann W; Olliff, Tom

    2015-01-01

    Knowledge of climatic variability at small spatial extents (< 50 km) is needed to assess vulnerabilities of biological reserves to climate change. We used empirical and modeled weather station data to test if climate change has increased the synchrony of surface air temperatures among 50 sites within the Greater Yellowstone Area (GYA) of the interior western United States. This important biological reserve is the largest protected area in the Lower 48 states and provides critical habitat for some of the world's most iconic wildlife. We focused our analyses on temporal shifts and shape changes in the annual distributions of seasonal minimum and maximum air temperatures among valley-bottom and higher elevation sites from 1948-2012. We documented consistent patterns of warming since 1948 at all 50 sites, with the most pronounced changes occurring during the Winter and Summer when minimum and maximum temperature distributions increased. These shifts indicate more hot temperatures and less cold temperatures would be expected across the GYA. Though the shifting statistical distributions indicate warming, little change in the shape of the temperature distributions across sites since 1948 suggest the GYA has maintained a diverse portfolio of temperatures within a year. Spatial heterogeneity in temperatures is likely maintained by the GYA's physiographic complexity and its large size, which encompasses multiple climate zones that respond differently to synoptic drivers. Having a diverse portfolio of temperatures may help biological reserves spread the extinction risk posed by climate change.

  16. Greater commitment to the domestic violence training is required.

    PubMed

    Leppäkoski, Tuija Helena; Flinck, Aune; Paavilainen, Eija

    2015-05-01

    Domestic violence (DV) is a major public health problem with high health and social costs. A solution to this multi-faceted problem requires that various help providers work together in an effective and optimal manner when dealing with different parties of DV. The objective of our research and development project (2008-2013) was to improve the preparedness of the social and healthcare professionals to manage DV. This article focuses on the evaluation of interprofessional education (IPE) to provide knowledge and skills for identifying and intervening in DV and to improve collaboration among social and health care professionals and other help providers at the local and regional level. The evaluation data were carried out with an internal evaluation. The evaluation data were collected from the participants orally and in the written form. The participants were satisfied with the content of the IPE programme itself and the teaching methods used. Participation in the training sessions could have been more active. Moreover, some of the people who had enrolled for the trainings could not attend all of them. IPE is a valuable way to develop intervening in DV. However, greater commitment to the training is required from not only the participants and their superiors but also from trustees.

  17. Greater Avoidance of a Heroin-Paired Taste Cue is Associated with Greater Escalation of Heroin Self-Administration in Rats

    PubMed Central

    Imperio, Caesar G.; Grigson, Patricia S.

    2015-01-01

    Heroin addiction is a disease of chronic relapse affecting over half of its users. Therefore, modeling individual differences in addiction-like behavior is needed to better reflect the human condition. In a rodent model, avoidance of a cocaine-paired saccharin cue is associated with greater cocaine seeking and taking. Here, we tested whether rats would avoid a saccharin cue when paired with the opportunity to self-administer heroin and whether the rats that most greatly avoid the heroin-paired taste cue would exhibit the greatest drug escalation over time, the greatest willingness to work for drug, and the greatest heroin-induced relapse. Adult male Sprague-Dawley rats received 5 min access to a 0.15% saccharin solution followed by the opportunity to self-administer either saline or heroin for 3 h (short access) or 6 h (extended access). Following 16 – 18 pairings, terminal saccharin intake was used to categorize the rats into small (>200 licks/5min) or large (<200 licks/5min) suppressors and responding for drug was examined accordingly. Only 5% of the short access rats reached the criteria for large suppressors. This large suppressor did not differ from the small suppressors in drug taking behavior. Conversely, 50% of the extended access saccharin-heroin rats were large suppressors and showed the largest escalation of drug intake, drug-loading behavior, and the greatest relapse-like behaviors. Extended access small suppressors displayed drug-taking behaviors that were similar to rats in the short access heroin condition. Avoidance of a heroin-paired taste cue reliably identifies individual differences in addiction-like behavior for heroin using extended drug access. PMID:26214212

  18. Greater avoidance of a heroin-paired taste cue is associated with greater escalation of heroin self-administration in rats.

    PubMed

    Imperio, Caesar G; Grigson, Patricia S

    2015-08-01

    Heroin addiction is a disease of chronic relapse affecting over half of its users. Therefore, modeling individual differences in addiction-like behavior is needed to better reflect the human condition. In a rodent model, avoidance of a cocaine-paired saccharin cue is associated with greater cocaine seeking and taking. Here, we tested whether rats would avoid a saccharin cue when paired with the opportunity to self-administer heroin and whether the rats that most greatly avoid the heroin-paired taste cue would exhibit the greatest drug escalation over time, the greatest willingness to work for drug, and the greatest heroin-induced relapse. Adult male Sprague-Dawley rats received 5 min access to a 0.15% saccharin solution followed by the opportunity to self-administer either saline or heroin for 3 hr (short access) or 6 hr (extended access). Following 16 to 18 pairings, terminal saccharin intake was used to categorize the rats into small (>200 licks/5min) or large (<200 licks/5min) suppressors and responding for drug was examined accordingly. Only 5% of the short access rats reached the criteria for large suppressors. This large suppressor did not differ from the small suppressors in drug-taking behavior. On the other hand, 50% of the extended access saccharin-heroin rats were large suppressors and showed the largest escalation of drug intake, drug-loading behavior, and the greatest relapse-like behaviors. Extended access small suppressors displayed drug-taking behaviors that were similar to rats in the short access heroin condition. Avoidance of a heroin-paired taste cue reliably identifies individual differences in addiction-like behavior for heroin using extended drug access.

  19. Methodology for Software Reliability Prediction. Volume 1.

    DTIC Science & Technology

    1987-11-01

    models to express software reliability in terms of fault density (the number of faults per executable lines of code) and failure rate (the number of...Reliability Measurements ..................... 3-1 0 3.1 Software Quality Measurement Framework ............ 3-1 3.2 A Software Reliability Measurement Model ...3-3 3.2.1 A Model of the Software Failure Process .... 3-3 3.2.2 Organization of Software Reliability Measurements

  20. Reliability and Validity of Borderline Personality Disorder in Hospitalized Adolescents

    PubMed Central

    Glenn, Catherine R.; Klonsky, E. David

    2013-01-01

    Objective: Although the DSM-IV suggests that dysfunctional personality patterns can be traced back to adolescence, there is continued debate about whether borderline personality disorder (BPD) can be reliably and validly diagnosed before age 18. The current study examined the reliability and validity of BPD in a large sample of adolescent psychiatric patients. Method: BPD and Axis I disorders were assessed with validated structured interviews and a series of clinical, emotion, and personality correlates were assessed with validated self-report questionnaires. Results: Consistent with previous studies in adolescent clinical samples, approximately 30% of patients in the current sample met criteria for BPD. The nine BPD criteria demonstrated good internal consistency, equivalent to rates reported in adult samples. In addition, BPD was related to greater clinical severity and impairment as indexed by strong associations with all major Axis I disorders, as well as with dimensional measures of depression, anxiety, difficulties with emotion regulation, and impulsiveness. Notably, reliability and validity remained satisfactory even when analyses were limited to younger adolescents between the ages of 12 and 14. Conclusions: Overall, findings suggest that BPD can be reliably and validly diagnosed in adolescents as young as 12–14 years old. PMID:23970909

  1. Structural reliability assessment capability in NESSUS

    NASA Technical Reports Server (NTRS)

    Millwater, H.; Wu, Y.-T.

    1992-01-01

    The principal capabilities of NESSUS (Numerical Evaluation of Stochastic Structures Under Stress), an advanced computer code developed for probabilistic structural response analysis, are reviewed, and its structural reliability assessed. The code combines flexible structural modeling tools with advanced probabilistic algorithms in order to compute probabilistic structural response and resistance, component reliability and risk, and system reliability and risk. An illustrative numerical example is presented.

  2. 46 CFR 169.619 - Reliability.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Reliability. 169.619 Section 169.619 Shipping COAST... Electrical Steering Systems § 169.619 Reliability. (a) Except where the OCMI judges it impracticable, the... be below that necessary for the safe navigation of the vessel. (c) The strength and reliability...

  3. Making statistical inferences about software reliability

    NASA Technical Reports Server (NTRS)

    Miller, Douglas R.

    1988-01-01

    Failure times of software undergoing random debugging can be modelled as order statistics of independent but nonidentically distributed exponential random variables. Using this model inferences can be made about current reliability and, if debugging continues, future reliability. This model also shows the difficulty inherent in statistical verification of very highly reliable software such as that used by digital avionics in commercial aircraft.

  4. How Reliable Are Informal Reading Inventories?

    ERIC Educational Resources Information Center

    Spector, Janet E.

    2005-01-01

    Informal Reading Inventories (IRI) are often recommended as instructionally relevant measures of reading. However, they have also been criticized for inattention to technical quality. Examination of reliability evidence in nine recently revised IRIs revealed that fewer than half report reliability. Several appear to have sufficient reliability for…

  5. Making statistical inferences about software reliability

    NASA Technical Reports Server (NTRS)

    Miller, Douglas R.

    1986-01-01

    Failure times of software undergoing random debugging can be modeled as order statistics of independent but nonidentically distributed exponential random variables. Using this model inferences can be made about current reliability and, if debugging continues, future reliability. This model also shows the difficulty inherent in statistical verification of very highly reliable software such as that used by digital avionics in commercial aircraft.

  6. High Achievement in Mathematics Education in India: A Report from Mumbai

    ERIC Educational Resources Information Center

    Raman, Manya

    2010-01-01

    This paper reports a study aimed at characterizing the conditions that lead to high achievement in mathematics in India. The study involved eight schools in the greater Mumbai region. The main result of the study is that the notion of high achievement itself is problematic, as reflected in the reports about mathematics achievement within and…

  7. Reliability of the hypernephroma halo

    SciTech Connect

    Wong, W.S.; Cochran, S.T.; Waisman, J.

    1981-11-01

    The excretory urograms and renal arteriograms of 68 patients with renal adenocarcinoma and 84 patients with renal masses other than renal adenocarcinoma were reviewed. The radiographs were examined for the presence or absence of the ''hypernephroma halo.'' The sensitivity of this sign was observed to be only 6% and 35% on excretory urography and arteriography, respectively. The specificity was 92% and 77%. However, the overall accuracy for this sign was only 54% and 59%. The relation between the halo and its postulated structural correlate, the tumor capsule, was also examined. There was no significant association demonstrable. It was concluded that the hypernephroma halo is not a reliable sign for diagnosing renal adenocarcinoma and that it probably does not represent the tumor capsule.

  8. Confidence bounds on structural reliability

    NASA Technical Reports Server (NTRS)

    Mehta, S. R.; Cruse, T. A.; Mahadevan, S.

    1993-01-01

    Different approaches for quantifying physical, statistical, and model uncertainties associated with the distribution parameters which are aimed at determining structural reliability are described. Confidence intervals on the distribution parameters of the input random variables are estimated using four algorithms to evaluate uncertainty of the response. Design intervals are evaluated using either Monte Carlo simulation or an iterative approach. A first order approach can be used to compute a first approximation of the design interval, but its accuracy is not satisfactory. The regression approach which combines the iterative approach with Monte Carlo simulation is capable of providing good results if the performance function can be accurately represented using regression analysis. It is concluded that the design interval-based approach seems to be quite general and takes into account distribution and model uncertainties.

  9. Reliability on ISS Talk Outline

    NASA Technical Reports Server (NTRS)

    Misiora, Mike

    2015-01-01

    1. Overview of ISS 2. Space Environment and it effects a. Radiation b. Microgravity 3. How we ensure reliability a. Requirements b. Component Selection i. Note: I plan to stay away from talk about Rad Hardened components and talk about why we use older processors because they are less susceptible to SEUs. c. Testing d. Redundancy / Failure Tolerance e. Sparing strategies 4. Operational Examples a. Multiple MDM Failures on 6A due to hard drive failure In general, my plan is to only talk about data that is currently available via normal internet sources to ensure that I stay away from any topics that would be Export Controlled, ITAR, or NDA-controlled. The operational example has been well-reported on in the media and those are the details that I plan to cover. Additionally I am not planning on using any slides or showing any photos during the talk.

  10. Software reliability modeling and analysis

    NASA Technical Reports Server (NTRS)

    Scholz, F.-W.

    1986-01-01

    A discrete and, as approximation to it, a continuous model for the software reliability growth process are examined. The discrete model is based on independent multinomial trials and concerns itself with the joint distribution of the first occurrence time of its underlying events (bugs). The continuous model is based on the order statistics of N independent nonidentically distributed exponential random variables. It is shown that the spacings between bugs are not necessarily independent or exponentially (geometrically) distributed. However, there is a statistical rationale for viewing them so conditionally. Some identifiability problems are pointed out and resolved. In particular, it appears that the number of bugs in a program is not identifiable. Estimated upper bounds and confidence bounds for the residual program eror content are given based on the spacings of the first k bugs removed.

  11. Audience preferences are predicted by temporal reliability of neural processing

    PubMed Central

    Dmochowski, Jacek P.; Bezdek, Matthew A.; Abelson, Brian P.; Johnson, John S.; Schumacher, Eric H.; Parra, Lucas C.

    2014-01-01

    Naturalistic stimuli evoke highly reliable brain activity across viewers. Here we record neural activity from a group of naive individuals while viewing popular, previously-broadcast television content for which the broad audience response is characterized by social media activity and audience ratings. We find that the level of inter-subject correlation in the evoked encephalographic responses predicts the expressions of interest and preference among thousands. Surprisingly, ratings of the larger audience are predicted with greater accuracy than those of the individuals from whom the neural data is obtained. An additional functional magnetic resonance imaging study employing a separate sample of subjects shows that the level of neural reliability evoked by these stimuli covaries with the amount of blood-oxygenation-level-dependent (BOLD) activation in higher-order visual and auditory regions. Our findings suggest that stimuli which we judge favourably may be those to which our brains respond in a stereotypical manner shared by our peers. PMID:25072833

  12. Audience preferences are predicted by temporal reliability of neural processing.

    PubMed

    Dmochowski, Jacek P; Bezdek, Matthew A; Abelson, Brian P; Johnson, John S; Schumacher, Eric H; Parra, Lucas C

    2014-07-29

    Naturalistic stimuli evoke highly reliable brain activity across viewers. Here we record neural activity from a group of naive individuals while viewing popular, previously-broadcast television content for which the broad audience response is characterized by social media activity and audience ratings. We find that the level of inter-subject correlation in the evoked encephalographic responses predicts the expressions of interest and preference among thousands. Surprisingly, ratings of the larger audience are predicted with greater accuracy than those of the individuals from whom the neural data is obtained. An additional functional magnetic resonance imaging study employing a separate sample of subjects shows that the level of neural reliability evoked by these stimuli covaries with the amount of blood-oxygenation-level-dependent (BOLD) activation in higher-order visual and auditory regions. Our findings suggest that stimuli which we judge favourably may be those to which our brains respond in a stereotypical manner shared by our peers.

  13. RICOR's new development of a highly reliable integral rotary cooler: engineering and reliability aspects

    NASA Astrophysics Data System (ADS)

    Filis, Avishai; Pundak, Nachman; Barak, Moshe; Porat, Ze'ev; Jaeger, Mordechai

    2011-06-01

    The growing demand for EO applications that work around the clock 24hr/7days a week, such as in border surveillance systems, emphasizes the need for a highly reliable cryocooler having increased operational availability and decreased integrated system Life Cycle (ILS) cost. In order to meet this need RICOR has developed a new rotary Stirling cryocooler, model K508N, intended to double the K508's operating MTTF achieving 20,000 operating MTTF hours. The K508N employs RICOR's latest mechanical design technologies such as optimized bearings and greases, bearings preloading, advanced seals, laser welded cold finger and robust design structure with increased natural frequency compared to the K508 model. The cooler enhanced MTTF was demonstrated by a Validation and Verification (V&V) plan comprising analytical means and a comparative accelerated life test between the standard K508 and the K508N models. Particularly, point estimate and confidence interval for the MTTF improvement factor where calculated periodically during and after the test. The (V&V) effort revealed that the K508N meets its MTTF design goal. The paper will focus on the technical and engineering aspects of the new design. In addition it will discuss the market needs and expectations, investigate the reliability data of the present reference K508 model; and report the accelerate life test data and the statistical analysis methodology as well as its underlying assumptions and results.

  14. Childhood Obesity and Cognitive Achievement.

    PubMed

    Black, Nicole; Johnston, David W; Peeters, Anna

    2015-09-01

    Obese children tend to perform worse academically than normal-weight children. If poor cognitive achievement is truly a consequence of childhood obesity, this relationship has significant policy implications. Therefore, an important question is to what extent can this correlation be explained by other factors that jointly determine obesity and cognitive achievement in childhood? To answer this question, we exploit a rich longitudinal dataset of Australian children, which is linked to national assessments in math and literacy. Using a range of estimators, we find that obesity and body mass index are negatively related to cognitive achievement for boys but not girls. This effect cannot be explained by sociodemographic factors, past cognitive achievement or unobserved time-invariant characteristics and is robust to different measures of adiposity. Given the enormous importance of early human capital development for future well-being and prosperity, this negative effect for boys is concerning and warrants further investigation.

  15. Using Design To Achieve Sustainability

    EPA Science Inventory

    Sustainability is defined as meeting the needs of this generation without compromising the ability of future generations to meet their needs. This is a conditional statement that places the responsibility for achieving sustainability squarely in hands of designers and planners....

  16. Comparison of reliability performance of group connected and conventional HVDC transmission systems

    SciTech Connect

    Kuruganty, S.

    1995-10-01

    A group connected HVDC transmission scheme is a variant of the unit connection where instead of a single generator, a group of generators are directly connected to the converter. Studies conducted in the past indicated that significant cost reduction can be achieved using this scheme. This is mainly due to the elimination of many components which results in considerable capital and operating cost savings to the utility. Concerns regarding the reliability performance of unit connected schemes were raised, however, there has not been a detailed reliability study conducted. This paper addresses the reliability evaluation aspect of a group connected scheme and compares the reliability performance of the group connected scheme with that of the conventional common collector system. Reliability models for both schemes were developed using a hypothetical system model based on the Nelson River system. Practical system component outage data was used to examine the reliability performance of both schemes.

  17. Dietary breadth of grizzly bears in the Greater Yellowstone Ecosystem

    USGS Publications Warehouse

    Gunther, Kerry A.; Shoemaker, Rebecca; Frey, Kevin L.; Haroldson, Mark A.; Cain, Steven L; van Manen, Frank T.; Fortin, Jennifer K.

    2014-01-01

    Grizzly bears (Ursus arctos) in the Greater Yellowstone Ecosystem (GYE) are opportunistic omnivores that eat a great diversity of plant and animal species. Changes in climate may affect regional vegetation, hydrology, insects, and fire regimes, likely influencing the abundance, range, and elevational distribution of the plants and animals consumed by GYE grizzly bears. Determining the dietary breadth of grizzly bears is important to document future changes in food resources and how those changes may affect the nutritional ecology of grizzlies. However, no synthesis exists of all foods consumed by grizzly bears in the GYE. We conducted a review of available literature and compiled a list of species consumed by grizzly bears in the GYE. We documented >266 species within 200 genera from 4 kingdoms, including 175 plant, 37 invertebrate, 34 mammal, 7 fungi, 7 bird, 4 fish, 1 amphibian, and 1 algae species as well as 1 soil type consumed by grizzly bears. The average energy values of the ungulates (6.8 kcal/g), trout (Oncorhynchus spp., 6.1 kcal/g), and small mammals (4.5 kcal/g) eaten by grizzlies were higher than those of the plants (3.0 kcal/g) and invertebrates (2.7 kcal/g) they consumed. The most frequently detected diet items were graminoids, ants (Formicidae), whitebark pine seeds (Pinus albicaulis), clover (Trifolium spp.), and dandelion (Taraxacum spp.). The most consistently used foods on a temporal basis were graminoids, ants, whitebark pine seeds, clover, elk (Cervus elaphus), thistle (Cirsium spp.), and horsetail (Equisetum spp.). Historically, garbage was a significant diet item for grizzlies until refuse dumps were closed. Use of forbs increased after garbage was no longer readily available. The list of foods we compiled will help managers of grizzly bears and their habitat document future changes in grizzly bear food habits and how bears respond to changing food resources.

  18. Wise Detections of Known QSOS at Redshifts Greater Than Six

    NASA Technical Reports Server (NTRS)

    Blain, Andrew W.; Assef, Roberto; Stern, Daniel; Tsai, Chao-Wei; Eisenhardt, Peter; Bridge, Carrie; Benford, Dominic; Jarrett, Tom; Cutri, Roc; Petty, Sara; Wu, Jingwen; Wright, Edward L.

    2013-01-01

    We present WISE All-Sky mid-infrared (IR) survey detections of 55 % (17/31) of the known QSOs at z greater than 6 from a range of surveys: the SDSS, the CFHT-LS, FIRST, Spitzer and UK1DSS. The WISE catalog thus provides a substantial increase in tiie quantity of IR data available for these sources: 17 are detected in the WISE Wl (3.4 micrometer) band, 16 in W2 (4.6 micrometers), 3 in W3 (12 micrometers) and 0 in W4 (22micrometers). This is particularly important with Spitzer in its warm-mission phase and no faint follow-up capability at wavelengths longwards of 5 micrometers until the launch of JWST. WISE thus provides a useful tool for understanding QSOs found in forthcoming large-area optical/IR sky surveys, using PanSTARRS, SkyMapper, VISTA, DES and LSST. The rest-UV properties of the WISE-detected and the WISE-non-detected samples differ: the detections have brighter i/z-band magnitudes and redder rest-UV colors. This suggests thai a more aggressive hunt for very-high-redshift QSOs, by combining WISE Wl and W2 data with red observed optical colors could be effective at least, for a subset of dusty candidate QSOs. Stacking the WISE images of the WISE-non-detected QSOs indicates that they are on average significantly fainter than the WISE-detccted examples, and are thus not narrowly missing detection in the WISE catalog. The WISE-catalog detection of three of our sample in the W3 band indicates that their mid-ID flux can be detected individually, although there is no stacked W3 detection of sources detected in Wl but not. W3. Stacking analyses of WISE data for large AGN samples will be a useful tool, and high-redshifl. QSOs of all types will be easy targets for JWST.

  19. Home range dynamics, habitat selection, and survival of Greater Roadrunners

    USGS Publications Warehouse

    Kelley, S.W.; Ransom, D.; Butcher, J.A.; Schulz, G.G.; Surber, B.W.; Pinchak, W.E.; Santamaria, C.A.; Hurtado, L.A.

    2011-01-01

    Greater Roadrunners (Geococcyx californianus) are common, poorly studied birds of arid and semi-arid ecosystems in the southwestern United States. Conservation of this avian predator requires a detailed understanding of their movements and spatial requirements that is currently lacking. From 2006 to 2009, we quantified home-range and core area sizes and overlap, habitat selection, and survival of roadrunners (N= 14 males and 20 females) in north-central Texas using radio-telemetry and fixed kernel estimators. Median home-range and core-area sizes were 90.4 ha and 19.2 ha for males and 80.1 ha and 16.7 ha for females, respectively. The size of home range and core areas did not differ significantly by either sex or season. Our home range estimates were twice as large (x??= 108.9 ha) as earlier published estimates based on visual observations (x??= 28-50 ha). Mean percent overlap was 38.4% for home ranges and 13.7% for core areas. Male roadrunners preferred mesquite woodland and mesquite savanna cover types, and avoided the grass-forb cover type. Female roadrunners preferred mesquite savanna and riparian woodland cover types, and avoided grass-forb habitat. Kaplan-Meier annual survival probabilities for females (0.452 ?? 0.118[SE]) were twice that estimated for males (0.210 ?? 0.108), but this difference was not significant. Mortality rates of male roadrunners were higher than those of females during the spring when males call from elevated perches, court females, and chase competing males. Current land use practices that target woody-shrub removal to enhance livestock forage production could be detrimental to roadrunner populations by reducing availability of mesquite woodland and mesquite savanna habitat required for nesting and roosting and increasing the amount of grass-forb habitat that roadrunners avoid. ??2011 The Authors. Journal of Field Ornithology ??2011 Association of Field Ornithologists.

  20. Debris Flows Within The Greater Caucasus Northern Slope

    NASA Astrophysics Data System (ADS)

    Panova, S.

    Debris flows are recorded everywhere within the Greater Caucasus northern slope. In last decades studies of debris flows appeared to be very important due to an intensive anthropogenic activity in the mountainous areas. Debris flow spatial distribution, as well as their genesis and means of protection are critical, too. The studied terri- tory has significant absolute altitudes, especially in the central and eastern parts. Also large amount of atmospheric precipitation with maximum in a warm period is typical for the region. Modern glaciation with soil-covered moraine deposits of modern and Holocene age is developed in the region. Geological and geomorphological conditions lead to debris flows formation within the entire territory. However, the amount of atmospheric precipitation drastically decreases from west to east and in the eastern part (Dagestan) debris flow is less active than in the central even under the presence of enormous amounts of loose detrital material of different genesis. In the western part debris flows are less developed due to insignificant altitudes and considerable forest coverage and soil-cover. Powerful modern glaciation with vast development of purely moraine and fluvial-glacial deposits results in intensive debris flow activity in the central part of the northern slope (the Terek river basin). In the upper reaches of all the Terek tributaries moraine deposits reach up to several dozen meters. They are widespread at altitudes higher than 2000 m (above the forest boundary) and almost everywhere uncovered by soils. They are a key source of sediments under debris flow formation. Within the Greater Caucasus northern slope there are 1700 debris flow basins with the total area about 7000 km2. Their average area is 4.0 km2 with minimum 0.20 km2 and maximum 173.8 km2. Moreover, there are many riverbeds in the area where form mountain mud floods more than 3000 km long. Debris flows occur between January and October with clear altitudinal zoning