Science.gov

Sample records for achieved high concentrations

  1. Novel DDR Processing of Corn Stover Achieves High Monomeric Sugar Concentrations from Enzymatic Hydrolysis (230 g/L) and High Ethanol Concentration (10% v/v) During Fermentation

    SciTech Connect

    Chen, Xiaowen; Jennings, Ed; Shekiro, Joe; Kuhn, Erik M.; O'Brien, Marykate; Wang, Wei; Schell, Daniel J.; Himmel, Mike; Elander, Richard T.; Tucker, Melvin P.

    2015-04-03

    Distilling and purifying ethanol, butanol, and other products from second and later generation lignocellulosic biorefineries adds significant capital and operating cost for biofuels production. The energy costs associated with distillation affects plant gate and life cycle analysis costs. Lower titers in fermentation due to lower sugar concentrations from pretreatment increase both energy and production costs. In addition, higher titers decrease the volumes required for enzymatic hydrolysis and fermentation vessels. Therefore, increasing biofuels titers has been a research focus in renewable biofuels production for several decades. In this work, we achieved over 200 g/L of monomeric sugars after high solids enzymatic hydrolysis using the novel deacetylation and disc refining (DDR) process on corn stover. The high sugar concentrations and low chemical inhibitor concentrations from the DDR process allowed ethanol titers as high as 82 g/L in 22 hours, which translates into approximately 10 vol% ethanol. To our knowledge, this is the first time that 10 vol% ethanol in fermentation derived from corn stover without any sugar concentration or purification steps has been reported. Techno-economic analysis shows the higher titer ethanol achieved from the DDR process could significantly reduce the minimum ethanol selling price from cellulosic biomass.

  2. DMR (deacetylation and mechanical refining) processing of corn stover achieves high monomeric sugar concentrations (230 g L-1) during enzymatic hydrolysis and high ethanol concentrations (>10% v/v) during fermentation without hydrolysate purification or concentration

    SciTech Connect

    Chen, Xiaowen; Kuhn, Erik; Jennings, Edward W.; Nelson, Robert; Tao, Ling; Zhang, Min; Tucker, Melvin P.

    2016-04-01

    Distilling and purifying ethanol and other products from second generation lignocellulosic biorefineries adds significant capital and operating costs to biofuel production. The energy usage associated with distillation negatively affects plant gate costs and causes environmental and life-cycle impacts, and the lower titers in fermentation caused by lower sugar concentrations from pretreatment and enzymatic hydrolysis increase energy and water usage and ethanol production costs. In addition, lower ethanol titers increase the volumes required for enzymatic hydrolysis and fermentation vessels increase capital expenditure (CAPEX). Therefore, increasing biofuel titers has been a research focus in renewable biofuel production for several decades. In this work, we achieved approximately 230 g L-1 of monomeric sugars after high solid enzymatic hydrolysis using deacetylation and mechanical refining (DMR) processed corn stover substrates produced at the 100 kg per day scale. The high sugar concentrations and low chemical inhibitor concentrations achieved by the DMR process allowed fermentation to ethanol with titers as high as 86 g L-1, which translates into approximately 10.9% v/v ethanol. To our knowledge, this is the first time that titers greater than 10% v/v ethanol in fermentations derived from corn stover without any sugar concentration or purification steps have been reported. As a result, the potential cost savings from high sugar and ethanol titers achieved by the DMR process are also reported using TEA analysis.

  3. DMR (deacetylation and mechanical refining) processing of corn stover achieves high monomeric sugar concentrations (230 g L-1) during enzymatic hydrolysis and high ethanol concentrations (>10% v/v) during fermentation without hydrolysate purification or concentration

    DOE PAGES

    Chen, Xiaowen; Kuhn, Erik; Jennings, Edward W.; ...

    2016-04-01

    Distilling and purifying ethanol and other products from second generation lignocellulosic biorefineries adds significant capital and operating costs to biofuel production. The energy usage associated with distillation negatively affects plant gate costs and causes environmental and life-cycle impacts, and the lower titers in fermentation caused by lower sugar concentrations from pretreatment and enzymatic hydrolysis increase energy and water usage and ethanol production costs. In addition, lower ethanol titers increase the volumes required for enzymatic hydrolysis and fermentation vessels increase capital expenditure (CAPEX). Therefore, increasing biofuel titers has been a research focus in renewable biofuel production for several decades. In thismore » work, we achieved approximately 230 g L-1 of monomeric sugars after high solid enzymatic hydrolysis using deacetylation and mechanical refining (DMR) processed corn stover substrates produced at the 100 kg per day scale. The high sugar concentrations and low chemical inhibitor concentrations achieved by the DMR process allowed fermentation to ethanol with titers as high as 86 g L-1, which translates into approximately 10.9% v/v ethanol. To our knowledge, this is the first time that titers greater than 10% v/v ethanol in fermentations derived from corn stover without any sugar concentration or purification steps have been reported. As a result, the potential cost savings from high sugar and ethanol titers achieved by the DMR process are also reported using TEA analysis.« less

  4. Program for Area Concentration Achievement Testing.

    ERIC Educational Resources Information Center

    Golden, Anthony J.

    The Program for Area Concentration Achievement Testing (PACAT) produces the cooperative assessment instrument known as the Area Concentration Achievement Test (ACAT). The ACAT uses a model designed specifically to measure curricular strengths and weaknesses and to provide this information at the departmental level. PACAT has developed 57…

  5. The enhancement of antibody concentration and achievement of high cell density CHO cell cultivation by adding nucleoside.

    PubMed

    Takagi, Yasuhiro; Kikuchi, Takuya; Wada, Ryuta; Omasa, Takeshi

    2017-03-02

    Recently, with the dramatic increase in demand for therapeutic antibodies, Chinese hamster ovary (CHO) cell culture systems have made significant progress in recombinant antibody production. Over the past two decades, recombinant antibody productivity has been improved by more than 100-fold. Medium optimization has been identified as an important key approach for increasing product concentrations. In this study, we evaluated the effects of deoxyuridine addition to fed-batch cultures of antibody-expressing CHO cell lines. Furthermore, we investigated the effects of combined addition of deoxyuridine, thymidine, and deoxycytidine. Our results suggest that addition of these pyrimidine nucleosides can increase CHO cell growth, with no significant change in the specific production rate. As a result of the increased cell growth, the antibody concentration was elevated and we were able to achieve more than 9 g/L during 16 days of culture. Similar effects of nucleoside addition were observed in fed-batch cultures of a Fab fragment-expressing CHO cell line, and the final Fab fragment concentration was more than 4 g/L. This nucleoside addition strategy could be a powerful platform for efficient antibody production.

  6. Flat high concentration devices

    SciTech Connect

    Minano, J.C.; Gonzalez, J.C.; Zanesco, I.

    1994-12-31

    During the last five years new concentrators achieving the theoretical maximum acceptance-angle-concentration product have appeared. In addition, some of these concentrators are very compact (concentrator depth/aperture diameter smaller than 1/3). The feasibility of these concentrators for photovoltaic applications is studied. It is concluded that these concentrators may be useful for high concentration cells (irradiance for maximum efficiency greater than 800 suns) if these cells have a small size (diameter smaller than 5 mm). The concentrators may provide for this case an acceptance angle of {approx} {+-}2.7 degrees with concentration factor around 1,000x and a concentrator depth 10 times the cell diameter. Instantaneous direct insolation and ambient temperature measurements of Madrid and a thermal model of the heat sink is used to calculate the annual electric energy output with which different concentration factors are compared. Concentration of 1,000x is close to the one giving the maximum annual electrical output.

  7. Achieving high-pressure and high-temperature within a TEM: Crystallographic defects as hosts for concentrating and storing carbon deep within Earth

    NASA Astrophysics Data System (ADS)

    Wu, J.; Buseck, P. R.

    2013-12-01

    Transmission electron microscopy in combination with in-situ high-pressure and high-temperature measurements is uniquely able to provide high-resolution data about materials under conditions resembling those in Earth's interior. By using nanocontainers of graphitized carbon, it is possible to achieve pressures and temperatures up to 40 GPa and 1200 °C, respectively. A wide range of relatively simple minerals and mineral analogs have been examined using this approach. By studying alpha-PbO2-type titanium dioxide (TiO2) and perovskite-structured nickel-doped lanthanum chromate (LaCr0.5Ni0.5O3), we show the influence of crystallographic defects in concentrating and storing carbon within these analogs to minerals occurring deep inside Earth. Such in-situ observations are impossible by using existing conventional high-pressure techniques. Figure 1. Temporal compression sequence of an anatase nanocrystal with two visible fault planes inside a multi-walled graphitic cage. (a)-(g) The times indicated in each panel are from the start of irradiation. Pressure was generated by shrinkage of the cage resulting from displacement damage by electrons (30 A/cm2) at 770 C. The disappearance of anatase (101) planes and emergence of alpha-PbO2-type TiO2 (110) planes indicates a phase transition between (e) and (f) (see insets).

  8. Project for Area Concentration Achievement Testing (PACAT).

    ERIC Educational Resources Information Center

    Austin Peay State Univ., Clarksville, TN.

    The history of the Project for Area Concentration Achievement Testing (PACAT), a university based national curriculum assessment project, is described in this report. The project performs surveys of academic curricula by content area, collects examination items from the faculty of participating departments, and constructs, distributes, and scores…

  9. Thin solar concentrator with high concentration ratio

    NASA Astrophysics Data System (ADS)

    Lin, Jhe-Syuan; Liang, Chao-Wen

    2013-09-01

    Solar concentrators are often used in conjunction with III-V multi-junction solar cells for cost reduction and efficiency improvement purposes. High flux concentration ratio, high optical efficiency and high manufacture tolerance are the key features required for a successful solar concentrator design. This paper describes a novel solar concentrator that combines the concepts, and thus the advantages, of both the refractive type ad reflective type. The proposed concentrator design adopts the Etendue-cascading concept that allows the light beams from all the concentric annular entrance pupils to be collected and transferred to the solar cell with minimal loss. This concept enables the system to perform near its Etendue-Limit and have a high concentration ratio simultaneously. Thereby reducing the costs of solar cells and therefor achieves a better the per watts cost. The concentrator demonstrated has a thing aspect ratio of 0.19 with a zero back focal distance. The numerical aperture at the solar cell immersed inside the dielectric concentrator is as high as 1.33 achieving a unprecedented high optical concentration ratio design.

  10. Effect of carbon source on acclimatization of nitrifying bacteria to achieve high-rate partial nitrification of wastewater with high ammonium concentration

    NASA Astrophysics Data System (ADS)

    Mousavi, Seyyed Alireza; Ibrahim, Shaliza; Aroua, Mohamed Kheireddine

    2014-08-01

    Experiments in two laboratory-scale sequential batch reactors were carried out to investigate the effect of heterotrophic bacteria on nitrifying bacteria using external carbon sources. Partial nitrification of ammonium-rich wastewater during short-term acclimatization enriched the activity of ammonia-oxidizing bacteria in both reactors. Heterotrophic bacteria exhibited a minor effect on nitrifying bacteria, and complete removal of ammonium occurred at a rate of 41 mg L-1 h-1 in both reactors. The main strategy of this research was to carry out partial nitrification using high-activity ammonia-oxidizing bacteria with a high concentration of free ammonia (70 mg L-1). The NO2 -/(NO3 - + NO2 -) ratio was greater than 0.9 in both reactors most of the time.

  11. Achieving extremely concentrated aqueous dispersions of graphene flakes and catalytically efficient graphene-metal nanoparticle hybrids with flavin mononucleotide as a high-performance stabilizer.

    PubMed

    Ayán-Varela, M; Paredes, J I; Guardia, L; Villar-Rodil, S; Munuera, J M; Díaz-González, M; Fernández-Sánchez, C; Martínez-Alonso, A; Tascón, J M D

    2015-05-20

    The stable dispersion of graphene flakes in an aqueous medium is highly desirable for the development of materials based on this two-dimensional carbon structure, but current production protocols that make use of a number of surfactants typically suffer from limitations regarding graphene concentration or the amount of surfactant required to colloidally stabilize the sheets. Here, we demonstrate that an innocuous and readily available derivative of vitamin B2, namely the sodium salt of flavin mononucleotide (FMNS), is a highly efficient dispersant in the preparation of aqueous dispersions of defect-free, few-layer graphene flakes. Most notably, graphene concentrations in water as high as ∼50 mg mL(-1) using low amounts of FMNS (FMNS/graphene mass ratios of about 0.04) could be attained, which facilitated the formation of free-standing graphene films displaying high electrical conductivity (∼52000 S m(-1)) without the need of carrying out thermal annealing or other types of post-treatment. The excellent performance of FMNS as a graphene dispersant could be attributed to the combined effect of strong adsorption on the sheets through the isoalloxazine moiety of the molecule and efficient colloidal stabilization provided by its negatively charged phosphate group. The FMNS-stabilized graphene sheets could be decorated with nanoparticles of several noble metals (Ag, Pd, and Pt), and the resulting hybrids exhibited a high catalytic activity in the reduction of nitroarenes and electroreduction of oxygen. Overall, the present results should expedite the processing and implementation of graphene in, e.g., conductive inks, composites, and hybrid materials with practical utility in a wide range of applications.

  12. High concentration dust monitor

    NASA Astrophysics Data System (ADS)

    Lilienfeld, P.

    1981-06-01

    The development, design, fabrication, and testing of a portable, self-contained prototype monitoring instrument capable of detecting and measuring airborne coal dust levels as concentrations in the range of 20 to 500 g/cu m is described. The output of the high concentration dust monitor is essentially independent of particle size and composition, with a response time of 10 seconds. Direct concentration readout as well as internal memory or recording capabilities are incorporated in the device. The operation of the instrument is based on direct sensing of the mass concentration of airborne dust by air-path beta radiation attenuation. The monitor is battery operated and incorporates a microprocessor that controls periodic automatic zero referencing, executes the mass computations, records the data for subsequent playback, and performs internal diagnostic checks.

  13. High-efficiency solar concentrator

    NASA Technical Reports Server (NTRS)

    Lansing, F. L.; Dorman, J.

    1976-01-01

    A new type of solar concentrator is presented using liquid lenses and simple translational tracking mechanism. The concentrator achieves a 100:1 nominal concentration ratio and is compared in performance with a flat-plate collector having two sheets of glazing and non-selective coating. The results of the thermal analysis show that higher temperatures can be obtained with the concentrator than is possible with the non-concentrator flat-plate type. Furthermore, the thermal efficiency far exceeds that of the comparative flat-plate type for all operating conditions.

  14. High-efficiency solar concentrator

    NASA Technical Reports Server (NTRS)

    Lansing, F. L.; Dorman, J.

    1980-01-01

    A new type of solar concentrator is presented using liquid lenses and simple translational tracking mechanism. The concentrator achieves a 100:1 nominal concentration ratio and is compared in performance with a flat-plate collector having two sheets of glazing and non-selective coating. The results of the thermal analysis show that higher temperatures can be obtained with the concentrator than is possible with the non-concentrator flat-plate type. Furthermore, the thermal efficiency far exceeds that of the comparative flat-plate type for all operating conditions.

  15. The Constraints of Poverty on High Achievement

    ERIC Educational Resources Information Center

    Burney, Virginia H.; Beilke, Jayne R.

    2008-01-01

    Research studies on school success often focus on the impact of discrete elements such as race, culture, ethnicity, gender, language, or school location on high achievement. The condition of poverty, however, may be the most important of all student differences in relation to high achievement; although not all schools have racial diversity, nearly…

  16. Self Regulated Learning of High Achievers

    ERIC Educational Resources Information Center

    Rathod, Ami

    2010-01-01

    The study was conducted on high achievers of Senior Secondary school. Main objectives were to identify the self regulated learners among the high achievers, to find out dominant components and characteristics operative in self regulated learners and to compare self regulated learning of learners with respect to their subject (science and non…

  17. Systemic Reform and Minority Student High Achievement.

    ERIC Educational Resources Information Center

    Treisman, Philip Uri; Surles, Stephanie A.

    The under-representation of African American and Hispanic American students among high achievers on standardized tests, honors graduates of most colleges, and practitioners of mathematics and science professions is well-documented. This paper explores the extent to which the current educational reform movement is achieving the goal of…

  18. Student Perceptions of High-Achieving Classmates

    ERIC Educational Resources Information Center

    Händel, Marion; Vialle, Wilma; Ziegler, Albert

    2013-01-01

    The reported study investigated students' perceptions of their high-performing classmates in terms of intelligence, social skills, and conscientiousness in different school subjects. The school subjects for study were examined with regard to cognitive, physical, and gender-specific issues. The results show that high academic achievements in…

  19. High Stakes Testing and Student Achievement.

    ERIC Educational Resources Information Center

    Ediger, Marlow

    The effects of high stakes testing may be critical in the lives of public school students and may have many consequences for schools and teachers. There are no easy answers in measuring student achievement and in holding teachers accountable for learner progress. High stakes testing also involves responsibilities on the part of the principal who…

  20. High Achievers: 23rd Annual Survey. Attitudes and Opinions from the Nation's High Achieving Teens.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Northbrook, IL.

    This report presents data from an annual survey of high school student leaders and high achievers. It is noted that of the nearly 700,000 high achievers featured in this edition, 5,000 students were sent the survey and 2,092 questionnaires were completed. Subjects were high school juniors and seniors selected for recognition by their principals or…

  1. Achieving High Performance Perovskite Solar Cells

    NASA Astrophysics Data System (ADS)

    Yang, Yang

    2015-03-01

    Recently, metal halide perovskite based solar cell with the characteristics of rather low raw materials cost, great potential for simple process and scalable production, and extreme high power conversion efficiency (PCE), have been highlighted as one of the most competitive technologies for next generation thin film photovoltaic (PV). In UCLA, we have realized an efficient pathway to achieve high performance pervoskite solar cells, where the findings are beneficial to this unique materials/devices system. Our recent progress lies in perovskite film formation, defect passivation, transport materials design, interface engineering with respect to high performance solar cell, as well as the exploration of its applications beyond photovoltaics. These achievements include: 1) development of vapor assisted solution process (VASP) and moisture assisted solution process, which produces perovskite film with improved conformity, high crystallinity, reduced recombination rate, and the resulting high performance; 2) examination of the defects property of perovskite materials, and demonstration of a self-induced passivation approach to reduce carrier recombination; 3) interface engineering based on design of the carrier transport materials and the electrodes, in combination with high quality perovskite film, which delivers 15 ~ 20% PCEs; 4) a novel integration of bulk heterojunction to perovskite solar cell to achieve better light harvest; 5) fabrication of inverted solar cell device with high efficiency and flexibility and 6) exploration the application of perovskite materials to photodetector. Further development in film, device architecture, and interfaces will lead to continuous improved perovskite solar cells and other organic-inorganic hybrid optoelectronics.

  2. Reliability achievement in high technology space systems

    NASA Technical Reports Server (NTRS)

    Lindstrom, D. L.

    1981-01-01

    The production of failure-free hardware is discussed. The elements required to achieve such hardware are: technical expertise to design, analyze, and fully understand the design; use of high reliability parts and materials control in the manufacturing process; and testing to understand the system and weed out defects. The durability of the Hughes family of satellites is highlighted.

  3. Oral hormone replacement therapy: factors that influence the estradiol concentrations achieved in a multiracial study population.

    PubMed

    Gavaler, Judith S

    2002-02-01

    The assumption that estradiol (E2) concentrations are reliably increased to therapeutic levels in postmenopausal women receiving hormone replacement therapy (HRT) has not been explicitly tested. Nor have factors that may modulate the E2 levels achieved been evaluated. The author examined E2 concentrations in a multiracial study population of 309 postmenopausal women treated with oral HRT and observed that 51.1% had achieved estradiol levels of at least 45 pg/ml (achievers). The odds of being an achiever were significantly elevated among non-Caucasian women by a HRT dose greater than 0.625 mg, current moderate drinking, and increasing duration of HRT use. The odds were significantly decreased by having a high school education or less and increasing time since last HRT dose. White postmenopausal women had significantly reduced odds of being an achiever, and both a dose of less than 0.625 mg and a dose equal to 0.625 mg significantly reduced the odds of being an achiever. Increasing body mass index and menopause duration were both associated with lower odds. This report demonstrates not only that women treated with HRTdo not all achieve therapeutic levels of estradiol but also that factors can be identified that modulate the E2 concentration achieved in response to HRT administration.

  4. Conditions for achieving ideal and Lambertian symmetrical solar concentrators

    SciTech Connect

    Luque, A.; Lorenzo, E.

    1982-10-15

    Symmetrical bidimensional concentrators are discussed, and it is proven that for a given source's angular extension a curve exists that divides the plane into two regions. No ideal concentrator can be found with its edges on the outer region and no Lambertian concentrator can be found with its edges on the inner region. A consequence of this theorem is that a concentrator is forced to cast some of the incident energy outside the collector to ensure its obtaining the maximum power.

  5. High concentration plasma-reduced plateletapheresis concentrates.

    PubMed

    Perseghin, Paolo

    2011-06-01

    Single-donor hyperconcentrated plateletapheresis (dry-platelets) collection has been introduced in the 90's as a part of the newly developed multi-component collection strategy. This approach allowed to safely collect multiple components from a single apheresis donation, i.e. RBC, FFP and/or plateletpheresis units. Dry-platelets are usually resuspended in additive solution to maintain an adequate pH during the storage period until use. Some concern existed about possible higher degrees of platelet activation in dry-platelets units when compared to standard concentration (1.0-1.6 × 10(6)/μL platelets) units and its possible correlation with lower in vivo efficiency and/or survival of the former units. Several authors investigated this specific issue, and dry-platelets units proved to be equally effective than standard concentration plateletpheresis units in recipients. The use of dry-platelets units may reduce (i) the risk of passive infusion of naturally occurring ABO-related hemolytic antibodies when donor O platelets are given to group A, B, or AB recipient, (ii) the risk of TRALI when multiparous donors undergo plateletpheresis. Furthermore, dry-platelet collection may allow for an increased amount of FFP sent to industry. Finally, hyperconcentrated platelet units may be used for "niche" indications, such as intrauterine platelet transfusion or, in case of autologous dry-platelet collection, for further freezing for long term storage in selected patients within onco-hematological settings.

  6. Conditions for achieving ideal and Lambertian symmetrical solar concentrators.

    PubMed

    Luque, A; Lorenzo, E

    1982-10-15

    In this paper we are concerned with symmetrical bidimensional concentrators, and we prove that for a given source's angular extension a curve exists that divides the plane into two regions. No ideal concentrator can be found with its edges on the outer region and no Lambertian concentrator can be found with its edges on the inner region. A consequence of this theorem is that a concentrator is forced to cast some of the incident energy outside the collector to ensure its obtaining the maximum power.

  7. Early predictors of high school mathematics achievement.

    PubMed

    Siegler, Robert S; Duncan, Greg J; Davis-Kean, Pamela E; Duckworth, Kathryn; Claessens, Amy; Engel, Mimi; Susperreguy, Maria Ines; Chen, Meichu

    2012-07-01

    Identifying the types of mathematics content knowledge that are most predictive of students' long-term learning is essential for improving both theories of mathematical development and mathematics education. To identify these types of knowledge, we examined long-term predictors of high school students' knowledge of algebra and overall mathematics achievement. Analyses of large, nationally representative, longitudinal data sets from the United States and the United Kingdom revealed that elementary school students' knowledge of fractions and of division uniquely predicts those students' knowledge of algebra and overall mathematics achievement in high school, 5 or 6 years later, even after statistically controlling for other types of mathematical knowledge, general intellectual ability, working memory, and family income and education. Implications of these findings for understanding and improving mathematics learning are discussed.

  8. Unusually high indoor radon concentrations

    NASA Astrophysics Data System (ADS)

    Ennemoser, O.; Ambach, W.; Brunner, P.; Schneider, P.; Oberaigner, W.; Purtscheller, F.; Stingl, V.

    Measurements of indoor radon concentrations in the village Umhausen (2600 inhabitants, Ötztal valley, Tyrol, Austria) revealed unusually high indoor radon concentrations up to 274,000 Bq m -3. The medians measured on the basements were 3750 Bq m -3 in winter and 361 Bq m -3 in summer, those on the ground floors were 1180 Bq m -3 and 210 Bq m -3, respectively. Seventy-one per cent of the houses showed basement radon concentrations above the Austrian action level of 400 Bq m -3 in winter, 33% in summer. There are indications that the high radon concentrations are due to a giant rock slide about 8700 years ago. The unusually high radon concentrations in Umhausen coincide with a statistically significant increase in lung cancer mortality. For the period 1970-1991 the age and sex standardized mortality rate is 3.85 (95% confidence interval: 2.9 to 5.1). The control population is the total population of Tyrol (630,000 inhabitants).

  9. Attitudes and Opinions from the Nation's High Achieving Teens. 18th Annual Survey of High Achievers.

    ERIC Educational Resources Information Center

    Educational Communications, Inc., Lake Forest, IL.

    This document contains factsheets and news releases which cite findings from a national survey of 1,985 high achieving high school students. Factsheets describe the Who's Who Among American High School Students recognition and service program for high school students and explain the Who's Who survey. A summary report of this eighteenth annual…

  10. Advanced high efficiency concentrator cells

    SciTech Connect

    Gale, R. . Varian Research Center)

    1992-06-01

    This report describes research to develop the technology needed to demonstrate a monolithic, multijunction, two-terminal, concentrator solar cell with a terrestrial power conversion efficiency greater than 35%. Under three previous subcontracts, Varian developed many of the aspects of a technology needed to fabricate very high efficiency concentrator cells. The current project was aimed at exploiting the new understanding of high efficiency solar cells. Key results covered in this report are as follows. (1) A 1.93-eV AlGaAs/1.42-eV GaAs metal-interconnected cascade cell was manufactured with a one-sun efficiency at 27.6% at air mass 1.5 (AM1.5) global. (2) A 1.0eV InGaAs cell was fabricated on the reverse'' side of a low-doped GaAs substrate with a one-sun efficiency of 2.5% AM1.5 diffuse and a short-circuit current of 14.4 mA/cm{sup 2}. (3) Small-scale manufacturing of GaAs p/n concentrator cells was attempted and obtained an excellent yield of high-efficiency cells. (4) Grown-in tunnel junction cell interconnects that are transparent and thermally stable using C and Si dopants were developed. 10 refs.

  11. 22nd Annual Survey of High Achievers: Attitudes and Opinions from the Nation's High Achieving Teens.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Northbrook, IL.

    This study surveyed high school students (N=1,879) who were student leaders or high achievers in the spring of 1991 for the purpose of determining their attitudes. Students were members of the junior or senior high school class during the 1990-91 academic year and were selected for recognition by their principals or guidance counselors, other…

  12. Individualizing amikacin regimens: accurate method to achieve therapeutic concentrations.

    PubMed

    Zaske, D E; Cipolle, R J; Rotschafer, J C; Kohls, P R; Strate, R G

    1991-11-01

    Amikacin's pharmacokinetics and dosage requirements were studied in 98 patients receiving treatment for gram-negative infections. A wide interpatient variation in the kinetic parameters of the drug occurred in all patients and in patients who had normal serum creatinine levels or normal creatinine clearance. The half-life ranged from 0.7 to 14.4 h in 74 patients who had normal serum creatinine levels and from 0.7 to 7.2 h in 37 patients who had normal creatinine clearance. The necessary daily dose to obtain therapeutic serum concentrations ranged from 1.25 to 57 mg/kg in patients with normal serum creatinine levels and from 10 to 57 mg/kg in patients with normal creatinine clearance. In four patients (4%), a significant change in baseline serum creatinine level (greater than 0.5 mg/dl) occurred during or after treatment, which may have been amikacin-associated toxicity. Overt ototoxicity occurred in one patient. The method of individualizing dosage regimens provided a clinically useful means of rapidly attaining therapeutic peak and trough serum concentrations.

  13. Attitudes and Opinions from the Nation's High Achieving Teens: 26th Annual Survey of High Achievers.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Lake Forest, IL.

    A national survey of 3,351 high achieving high school students (junior and senior level) was conducted. All students had A or B averages. Topics covered include lifestyles, political beliefs, violence and entertainment, education, cheating, school violence, sexual violence and date rape, peer pressure, popularity, suicide, drugs and alcohol,…

  14. Attitudes and Opinions from the Nation's High Achieving Teens. 24th Annual Survey of High Achievers.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Lake Forest, IL.

    This survey represents information compiled by the largest national survey of adolescent leaders and high achievers. Of the 5,000 students selected demographically from "Who's Who Among American High School Students," 1,957 responded. All students surveyed had "A" or "B" averages, and 98% planned on attending college. Questions were asked about…

  15. Non-tracking solar concentrator with a high concentration ratio

    DOEpatents

    Hinterberger, Henry

    1977-01-01

    A nontracking solar concentrator with a high concentration ratio is provided. The concentrator includes a plurality of energy absorbers which communicate with a main header by which absorbed heat is removed. Undesired heat flow of those absorbers not being heated by radiant energy at a particular instant is impeded, improving the efficiency of the concentrator.

  16. Horizontally staggered lightguide solar concentrator with lateral displacement tracking for high concentration applications.

    PubMed

    Ma, Hongcai; Wu, Lin

    2015-07-10

    We present the design of a horizontally staggered lightguide solar concentrator with lateral displacement tracking for high concentration applications. This solar concentrator consists of an array of telecentric primary concentrators, a horizontally staggered lightguide layer, and a vertically tapered lightguide layer. The primary concentrator is realized by two plano-aspheric lenses with lateral movement and maintains a high F-number over an angle range of ±23.5°. The results of the simulations show that the solar concentrator achieves a high concentration ratio of 500× with ±0.5° of acceptance angle by a single-axis tracker and dual lateral translation stages.

  17. High Involvement Mothers of High Achieving Children: Potential Theoretical Explanations

    ERIC Educational Resources Information Center

    Hunsaker, Scott L.

    2013-01-01

    In American society, parents who have high aspirations for the achievements of their children are often viewed by others in a negative light. Various pejoratives such as "pushy parent," "helicopter parent," "stage mother," and "soccer mom" are used in the common vernacular to describe these parents. Multiple…

  18. Does High School Homework Increase Academic Achievement?

    ERIC Educational Resources Information Center

    Kalenkoski, Charlene Marie; Pabilonia, Sabrina Wulff

    2017-01-01

    Although previous research has shown that homework improves students' academic achievement, the majority of these studies use data on students' homework time from retrospective questionnaires, which may be less accurate than time-diary data. We use data from the combined Child Development Supplement (CDS) and the Transition to Adulthood Survey…

  19. Factors Implicated in High Mathematics Achievement

    ERIC Educational Resources Information Center

    Forgasz, Helen J.; Hill, Janelle C.

    2013-01-01

    The most recent Program for International Student Assessment (PISA) (2009) mathematical literacy results provide evidence that in Western English-speaking countries, including Australia, the gender gap in achievement appears to be widening in favour of males. In the study reported in this article, the aim was to explore the effects of gender,…

  20. High Ability Readers and the Achievement Gap

    ERIC Educational Resources Information Center

    Hunsaker, Scott L.; Parke, Cynthia J.; Bramble, Joan G.

    2004-01-01

    To close the achievement gap, the "No Child Left Behind" law calls for all students to make appropriate yearly progress. This presumably means that progress is being made by capable readers at the same time progress is being made by struggling readers. However, there appear to be unintended effects of "No Child Left Behind"…

  1. High-Achieving Students in the Era of NCLB

    ERIC Educational Resources Information Center

    Loveless, Tom; Parkas, Steve; Duffett, Ann

    2008-01-01

    This report contains two separate studies examining the status of high-achieving students in the No Child Left Behind (NCLB) era. Part I, An Analysis of NAEP Data, authored by Brookings Institution scholar Tom Loveless, examines achievement trends for high-achieving students (defined, like low-achieving students, by their performance on the…

  2. Improving Student Achievement: A Study of High-Poverty Schools with Higher Student Achievement Outcomes

    ERIC Educational Resources Information Center

    Butz, Stephen D.

    2012-01-01

    This research examined the education system at high-poverty schools that had significantly higher student achievement levels as compared to similar schools with lower student achievement levels. A multischool qualitative case study was conducted of the educational systems where there was a significant difference in the scores achieved on the…

  3. Achieving strategic surety for high consequence software

    SciTech Connect

    Pollock, G.M.

    1996-09-01

    A strategic surety roadmap for high consequence software systems under the High Integrity Software (HIS) Program at Sandia National Laboratories guides research in identifying methodologies to improve software surety. Selected research tracks within this roadmap are identified and described detailing current technology and outlining advancements to be pursued over the coming decade to reach HIS goals. The tracks discussed herein focus on Correctness by Design, and System Immunology{trademark}. Specific projects are discussed with greater detail given on projects involving Correct Specification via Visualization, Synthesis, & Analysis; Visualization of Abstract Objects; and Correct Implementation of Components.

  4. Achieving High-Temperature Ferromagnetic Topological Insulator

    NASA Astrophysics Data System (ADS)

    Katmis, Ferhat

    Topological insulators (TIs) are insulating materials that display conducting surface states protected by time-reversal symmetry, wherein electron spins are locked to their momentum. This unique property opens new opportunities for creating next-generation electronic and spintronic devices, including TI-based quantum computation. Introducing ferromagnetic order into a TI system without compromising its distinctive quantum coherent features could lead to a realization of several predicted novel physical phenomena. In particular, achieving robust long-range magnetic order at the TI surface at specific locations without introducing spin scattering centers could open up new possibilities for devices. Here, we demonstrate topologically enhanced interface magnetism by coupling a ferromagnetic insulator (FMI) to a TI (Bi2Se3); this interfacial ferromagnetism persists up to room temperature, even though the FMI (EuS) is known to order ferromagnetically only at low temperatures (<17 K). The induced magnetism at the interface resulting from the large spin-orbit interaction and spin-momentum locking feature of the TI surface is found to greatly enhance the magnetic ordering (Curie) temperature of the TI/FMI bilayer system. Due to the short range nature of the ferromagnetic exchange interaction, the time-reversal symmetry is broken only near the surface of a TI, while leaving its bulk states unaffected. The topological magneto-electric response originating in such an engineered TI could allow for an efficient manipulation of the magnetization dynamics by an electric field, providing an energy efficient topological control mechanism for future spin-based technologies. Work supported by MIT MRSEC through the MRSEC Program of NSF under award number DMR-0819762, NSF Grant DMR-1207469, the ONR Grant N00014-13-1-0301, and the STC Center for Integrated Quantum Materials under NSF grant DMR-1231319.

  5. Norview High School: Leadership Fosters Achievment

    ERIC Educational Resources Information Center

    Principal Leadership, 2013

    2013-01-01

    Often little unsaid things demonstrate what is truly important in a school. When teachers have common planning time and all of the department chairs share a single space as they do at Norview High School in Norfolk, VA, the unmistakable message is that instructional collaboration and leadership are expected and valued. Norview, an urban,…

  6. Self-Concept and Achievement Motivation of High School Students

    ERIC Educational Resources Information Center

    Lawrence, A. S. Arul; Vimala, A.

    2013-01-01

    The present study "Self-concept and Achievement Motivation of High School Students" was investigated to find the relationship between Self-concept and Achievement Motivation of High School Students. Data for the study were collected using Self-concept Questionnaire developed by Raj Kumar Saraswath (1984) and Achievement Motive Test (ACMT)…

  7. Gun requirements to achieve high field spheromaks

    SciTech Connect

    Fowler, T K

    1999-03-04

    It is shown that a gun similar to that in the SSPX could demonstrate the high fields required for Pulsed Spheromak reactors merely by prolonging the pulse. Important considerations are choosing the voltage to exceed ohmic losses; designing the gun to avoid wasteful short-circuiting of current within the gun; and the injection efficiency factor, f, determined by the ''sag'' in the profile of {lambda} = {mu}{sub o}j/B. Typically f = 0.75 in experiments, giving an overall efficiency > 50 % if short-circuiting is avoided. Theoretical transport models agree qualitatively with the need for a finite gradient in h to pump in helicity by current-driven tearing modes and suggest that pressure-driven resistive modes would not compete with current-driven modes during a buildup to ohmic ignition.

  8. High-concentration photovoltaic module design

    SciTech Connect

    Levy, S.L.; Stoddard, L.E.

    1986-08-01

    Over the past 3 years, Black and Veatch has been leading a team in the ongoing design of a high-concentration, high-performance photovoltaic (PV) module for the Electric Power Research Institute (EPRI). The current design consists of a deep-drawn aluminized steel housing containing 48 cell packages in a 4-row by 12-column matrix. Each cell package includes an anodized aluminum secondary optical element, a 27.5% efficient Stanford University/EPRI 500X concentration point contact silicon PV cell, an alumina substrate, and a copper heat spreader. Developmental efforts underway for a comolded glass/polymer Fresnel lens parquet indicate the potential for a substantial decrease in molding time and, thereby, cost, in comparison to more conventional compression molding of acrylic lenses. Further development is necessary to achieve comparable optical performance of the lens. Current activities have included the development of PVOPTICS, a Monte Carlo computer code particularly suited to the module optical design. The module is projected to produce 287 watts at an efficiency of 22%. The module cost, at large production rates, is estimated to be $275 ($0.96 per watt).

  9. Effects of Learning Styles and Interest on Concentration and Achievement of Students in Mobile Learning

    ERIC Educational Resources Information Center

    Li, Xiaojie; Yang, Xianmin

    2016-01-01

    Learning concentration deserves in-depth investigation in the field of mobile learning. Therefore, this study examined the interaction effects of learning styles and interest on the learning concentration and academic achievement of students who were asked to learn conceptual knowledge via their mobile phones in a classroom setting. A total of 92…

  10. Design and development of a high-concentration photovoltaic concentrator

    SciTech Connect

    Hodge, R C

    1982-04-01

    The design and development of a high concentration photovoltaic concentrator module is discussed. The design concept described herein incorporates a curved groove domed Fresnel lens, a high concentration etched multiple vertical junction (EMVJ) solar cell and a passively cooled direct-bonded copper cell mount all packaged in a plastic module. Two seven inch diameter 1200x domed Fresnel lenses were fabricated using single point diamond turning technology. Testing at both GE and Sandia confirmed optical transmission efficiencies of over 83%. Samples of the latest available EMVJ cells were mounted and installed, with a domed Fresnel lens, into a prototype module. Subsequent testing demonstrated net lens-cell efficiencies of 10 to 13%. As a result of this program, salient conclusions have been formulated as to this technology.

  11. Scientific Temper among Academically High and Low Achieving Adolescent Girls

    ERIC Educational Resources Information Center

    Kour, Sunmeet

    2015-01-01

    The present study was undertaken to compare the scientific temper of high and low achieving adolescent girl students. Random sampling technique was used to draw the sample from various high schools of District Srinagar. The sample for the present study consisted of 120 school going adolescent girls (60 high and 60 low achievers). Data was…

  12. The "Renaissance Child": High Achievement and Gender in Late Modernity

    ERIC Educational Resources Information Center

    Skelton, Christine; Francis, Becky

    2012-01-01

    This paper draws on the concept of the "Renaissance Child" to illustrate the ways in which gender influences the opportunities and possibilities of high-achieving pupils. Using data from a study of 12-13-year high-achieving boys and girls based in schools in England, the paper considers the ways in which a group of popular boys was able…

  13. Does It Matter Where Poor Kids Live? A Look at Concentrated Poverty and Achievement.

    ERIC Educational Resources Information Center

    Schellenberg, Stephen J.

    This study sought to separate the effect of concentrated poverty on students' academic achievement and to develop a simple method for demonstrating that effect. The study was conducted in a midwestern urban school district with characteristics particularly suitable for answering these questions. It used two years worth of data on elementary school…

  14. Test-Taking Strategies of High and Low Mathematics Achievers

    ERIC Educational Resources Information Center

    Hong, Eunsook; Sas, Maggie; Sas, John C.

    2006-01-01

    The authors explored test-preparation and test-taking strategies that high school students used in algebra tests. From a pool of high school students (N = 156), 61 students participated in interviews, and of those interviewed, 26 represented those who were high achieving as well as highly interested in mathematics (n = 15) vs. those who were low…

  15. Highly concentrated foam formulation for blast mitigation

    DOEpatents

    Tucker, Mark D.; Gao, Huizhen

    2010-12-14

    A highly concentrated foam formulation for blast suppression and dispersion mitigation for use in responding to a terrorism incident involving a radiological dispersion device. The foam formulation is more concentrated and more stable than the current blast suppression foam (AFC-380), which reduces the logistics burden on the user.

  16. Some Correlates of High School Foreign Language Achievement.

    ERIC Educational Resources Information Center

    Beanblossom, Gary F.

    This paper investigates the influences of traditional kinds of verbal and quantitative achievement and aptitude variables on high school foreign language achievement, as measured by Modern Language Association and University of Washington tests of language skills administered to entering college students. The report focuses on: (1) the sample and…

  17. Strategic administration of enrofloxacin in poultry to achieve higher maximal serum concentrations.

    PubMed

    Sumano, L H; Gutierrez, O L; Zamora, Q M

    2003-03-01

    To achieve a higher maximal serum concentration (Cs(max)) of enrofloxacin after oral administration of 10mg/kg/day of three commercial preparations of enrofloxacin to chickens, two concentrations of the drug were tested (0.1 and 0.2%), under controlled laboratory conditions. A single oral bolus dose was delivered directly into the proventriculus of each of 240 chickens, which were equally divided into six groups: three received the customary concentration (0.1%), and three received the higher concentration. A quantitative/qualitative microbiological analytical method to determine serum concentrations of enrofloxacin and a software program to obtain pharmacokinetic variables, revealed that time vs. concentration relationships best fitted double peak shape curves, Cs(max1) and Cs(max2). Statistically significant (P>0.01) increments were obtained when 0.2% enrofloxacin oral solutions from the three different commercial preparations were administered. The increments ranged from 175% to 338% for Cs(max1) and 69% to 342% for Cs(max2). Optimal bactericidal concentrations of enrofloxacin are usually twice the value of their minimal inhibitory concentration. Although clinical trials are now required, it would appear that increments in the serum concentration of enrofloxacin may reduce to the rate at which bacterial resistance occurs and so increase clinical efficacy without affecting the cost per treatment.

  18. "Brains before "Beauty"?" High Achieving Girls, School and Gender Identities

    ERIC Educational Resources Information Center

    Skelton, Christine; Francis, Becky; Read, Barbara

    2010-01-01

    In recent years educational policy on gender and achievement has concentrated on boys' underachievement, frequently comparing it with the academic success of girls. This has encouraged a perception of girls as the "winners" of the educational stakes and assumes that they no longer experience the kinds of gender inequalities identified in…

  19. Attitudes and Opinions from the Nation's High Achieving Teens: 29th Annual Survey of High Achievers.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Lake Forest, IL.

    This report presents the 1998 statistical findings of the annual survey to determine the attitudes of national high school student leaders. Questionnaires were completed by 3,123 high school juniors and seniors, all of whom were selected for recognition in "Who's Who among American High School Students." In addition to demographic…

  20. Applications of nonimaging optics for very high solar concentrations

    SciTech Connect

    O`Gallagher, J.; Winston, R.

    1997-12-31

    Using the principles and techniques of nonimaging optics, solar concentrations that approach the theoretical maximum can be achieved. This has applications in solar energy collection wherever concentration is desired. In this paper, we survey recent progress in attaining and using high and ultrahigh solar fluxes. We review a number of potential applications for highly concentrated solar energy and the current status of the associated technology. By making possible new and unique applications for intense solar flux, these techniques have opened a whole new frontier for research and development of potentially economic uses of solar energy.

  1. Achievement Motivation Training for Potential High School Dropouts. Achievement Motivation Development Project Working Paper Number 4.

    ERIC Educational Resources Information Center

    McClelland, David C.

    This pilot project sought to determine if instruction in achievement motivation would help potential dropouts to complete their schooling. Subjects were tenth grade students in a suburban Boston high school. A one-week residential course during winter and spring vacations was taken by one group of six boys and a second group of four. Equated…

  2. Refractive Secondary Solar Concentrator Demonstrated High-Temperature Operation

    NASA Technical Reports Server (NTRS)

    Wong, Wayne A.

    2002-01-01

    Space applications that utilize solar thermal energy--such as electric power conversion systems, thermal propulsion systems, and furnaces--require highly efficient solar concentration systems. The NASA Glenn Research Center is developing the refractive secondary concentrator, which uses refraction and total internal reflection to efficiently concentrate and direct solar energy. When used in combination with advanced lightweight primary concentrators, such as inflatable thin films, the refractive secondary concentrator enables very high system concentration ratios and very high temperatures. Last year, Glenn successfully demonstrated a secondary concentrator throughput efficiency of 87 percent, with a projected efficiency of 93 percent using an antireflective coating. Building on this achievement, Glenn recently successfully demonstrated high-temperature operation of the secondary concentrator when it was used to heat a rhenium receiver to 2330 F. The high-temperature demonstration of the concentrator was conducted in Glenn's 68-ft long Tank 6 thermal vacuum facility equipped with a solar simulator. The facility has a rigid panel primary concentrator that was used to concentrate the light from the solar simulator onto the refractive secondary concentrator. NASA Marshall Space Flight Center provided a rhenium cavity, part of a solar thermal propulsion engine, to serve as the high-temperature receiver. The prototype refractive secondary concentrator, measuring 3.5 in. in diameter and 11.2 in. long, is made of single-crystal sapphire. A water-cooled splash shield absorbs spillage light outside of the 3.5-in. concentrator aperture. Multilayer foil insulation composed of tungsten, molybdenum, and niobium is used to minimize heat loss from the hightemperature receiver. A liquid-cooled canister calorimeter is used to measure the heat loss through the multilayer foil insulation.

  3. Attitudes and Opinions from the Nation's High Achieving Teens: 28th Annual Survey of High Achievers.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Lake Forest, IL.

    This report details the 28th annual study to examine the attitudes of student leaders in U.S. high schools. Participating in the survey were 3,210 adolescents, primarily 16- and 17-year-olds, who had been featured in the 1997 edition of "Who's Who Among American High School Students." The report presents demographic information on the…

  4. Attitudes and Opinions from the Nation's High Achieving Teens: 27th Annual Survey of High Achievers.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Lake Forest, IL.

    This report details the 27th annual study to examine the attitudes of student leaders in U.S. high schools. Participating in the survey were 3,370 adolescents, primarily 16- and 17-year-olds, who had been featured in the 1996 edition of "Who's Who Among American High School Students." The report presents demographic information on the survey…

  5. Freeform lens design to achieve 1000X solar concentration with a parabolic trough reflector

    NASA Astrophysics Data System (ADS)

    Wheelwright, Brian M.; Angel, Roger; Coughenour, Blake

    2014-12-01

    Line-focus parabolic trough mirrors for solar thermal generation cannot produce the high concentration required for concentrating photovoltaic (CPV) systems. We describe a freeform lens array with toroidal symmetry which intercepts the low-concentration line focus to produce a series of elongated, high-concentration foci. The design employs 2D Kӧhler illumination to improve the acceptance angle in one direction. The two-stage concentrator has 1000X average geometric concentration with an acceptance angle of +/-1.49° in the azimuthal direction and +/-0.29° in the elevation direction. Preliminary results of a prototype roll-forming process are shown in thermoplastics and B270 glass.

  6. Attitudes and Opinions from the Nation's High Achieving Teens. 25th Annual Survey of High Achievers.

    ERIC Educational Resources Information Center

    Who's Who among American High School Students, Lake Forest, IL.

    This survey was conducted during the spring of 1994 for the purpose of determining the attitudes of student leaders in the nation's high schools. Eight thousand surveys were sent out to students, of which 3177 were returned. All students surveyed were members of the junior or senior class during the 1993-94 academic year. They were selected for…

  7. Fluorescence quenching at high quencher concentrations

    NASA Astrophysics Data System (ADS)

    Peak, David; Werner, T. C.; Dennin, Richard M., Jr.; Baird, James K.

    1983-10-01

    Chemical reactions occurring in dense media at high reactant concentrations can be described by rate ``constants'' which are actually functions of concentration. We present a theoretical model in which this so-called rate constant ``renormalization'' occurs for the specific case of fluorescence quenching in solution. We show that both the quenching and the excitation rate constants can become concentration dependent. We fit our theory to several sets of experimental data—our own and some from the literature—and show that excellent agreement is obtained by varying a single free parameter, namely, the efficiency with which a fluorophore-quencher collision leads to a quench of the excited state.

  8. What Does Quality Programming Mean for High Achieving Students?

    ERIC Educational Resources Information Center

    Samudzi, Cleo

    2008-01-01

    The Missouri Academy of Science, Mathematics and Computing (Missouri Academy) is a two-year accelerated, early-entrance-to-college, residential school that matches the level, complexity and pace of the curriculum with the readiness and motivation of high achieving high school students. The school is a part of Northwest Missouri State University…

  9. High School Employment and Academic Achievement: A Note for Educators

    ERIC Educational Resources Information Center

    Keister, Mary; Hall, Joshua

    2010-01-01

    Educators are often in a position to affect student decisions to work during the school term. This study reviews and summarizes the literature on the effect that employment during high school has on academic achievement. The available evidence suggests that part-time jobs for high school students are beneficial as long as the number of hours…

  10. High-Stakes Testing: Does It Increase Achievement?

    ERIC Educational Resources Information Center

    Nichols, Sharon L.

    2007-01-01

    I review the literature on the impact on student achievement of high-stakes testing. Its popularity as a mechanism for holding educators accountable has triggered studies to examine whether its promise to increase student learning has been fulfilled. The review concludes there is no consistent evidence to suggest high-stakes testing leads to…

  11. Brain Hemisphericity and Mathematics Achievement of High School Students

    ERIC Educational Resources Information Center

    Fernandez, Sanny F.

    2011-01-01

    This study aimed to find out the brain hemisphericity and mathematics achievement of high school students. The respondents of the study were the 168 first year high school students of Colegio de San Jose, during school year 2010-2011 who were chosen through stratified random sampling. The descriptive and interview methods of research were used in…

  12. Exploring High-Achieving Students' Images of Mathematicians

    ERIC Educational Resources Information Center

    Aguilar, Mario Sánchez; Rosas, Alejandro; Zavaleta, Juan Gabriel Molina; Romo-Vázquez, Avenilde

    2016-01-01

    The aim of this study is to describe the images that a group of high-achieving Mexican students hold of mathematicians. For this investigation, we used a research method based on the Draw-A-Scientist Test (DAST) with a sample of 63 Mexican high school students. The group of students' pictorial and written descriptions of mathematicians assisted us…

  13. Achieving optimum carrier concentrations in p-doped SnS thermoelectrics.

    PubMed

    Bhattacharya, Sandip; Gunda, N S Harsha; Stern, Robin; Jacobs, Stéphane; Chmielowski, Radoslaw; Dennler, Gilles; Madsen, Georg K H

    2015-04-14

    Tin(II)sulfide, SnS, is a commercially viable and environmentally friendly thermoelectric material. Recently it was shown how the carrier concentration and the thermoelectric power factor can be optimized by Ag-doping in a sulphur rich environment. Theoretical calculations lead to a fairly accurate estimation of the carrier concentration, whereas the potential of doping with Li(+) is strongly overestimated. Two principally ubiquitous effects that can result in decreasing the hole concentration, namely the formation of coupled defect complexes and oxidation of the dopant, are discussed as possible origins of this disagreement. It is shown that oxidation limits the chemical potential of Li beyond that already set by the formation of Li2S. This work serves as a comprehensive guide to achieve an efficient p-doped SnS thermoelectric material.

  14. Achieving the College Dream? Examining Disparities in Access to College Information among High Achieving and Non-High Achieving Latina Students

    ERIC Educational Resources Information Center

    Kimura-Walsh, Erin; Yamamura, Erica K.; Griffin, Kimberly A.; Allen, Walter R.

    2009-01-01

    Using an Opportunity to Learn (OTL) framework, this study examines the college preparatory experiences of Latina high and non-high achievers at an urban Latina/o majority high school. Findings indicate that students relied almost exclusively on school resources to navigate their college preparation process. However, the school provided…

  15. A Desired PAR-Achieving Precoder Design for Multiuser MIMO OFDM Based on Concentration of Measure

    NASA Astrophysics Data System (ADS)

    Cha, Hyun-Su; Kim, Dong Ku

    2017-03-01

    For multi-user multiple-input and multiple-output (MIMO) wireless communications in orthogonal frequency di- vision multiplexing systems, we propose a MIMO precoding scheme providing a desired peak-to-average power ratio (PAR) at the minimum cost that is defined as received SNR degradation. By taking advantage of the concentration of measure, we formulate a convex problem with constraint on the desired PAR. Consequently, the proposed scheme almost exactly achieves the desired PAR on average, and asymptotically attains the desired PAR at the 0.001 point of its complementary cumulative distribution function, as the number of subcarriers increases.

  16. High-dimensional entanglement concentration of twisted photon pairs High-dimensional entanglement concentration

    NASA Astrophysics Data System (ADS)

    Chen, L. X.; Wu, Q. P.

    2012-10-01

    Recently, Dada et al. reported on the experimental entanglement concentration and violation of generalized Bell inequalities with orbital angular momentum (OAM) [Nat. Phys. 7, 677 (2011)]. Here we demonstrate that the high-dimensional entanglement concentration can be performed in arbitrary OAM subspaces with selectivity. Instead of violating the generalized Bell inequalities, the working principle of present entanglement concentration is visualized by the biphoton OAM Klyshko picture, and its good performance is confirmed and quantified through the experimental Shannon dimensionalities after concentration.

  17. Highly Concentrated Catalytic Asymmetric Allylation of Ketones

    PubMed Central

    Wooten, Alfred J.; Kim, Jeung Gon; Walsh, Patrick J.

    2008-01-01

    We report the catalytic asymmetric allylation of ketones under highly concentrated reaction conditions with a catalyst generated from titanium tetraisopropoxide and BINOL (1:2 ratio) in the presence of isopropanol. This catalyst promotes the addition of tetraallylstannane to a variety of ketones to produce tertiary homoallylic alcohols in excellent yield (80–99%) with high enantioselectivities (79–95%). The resulting homoallylic alcohols can also be epoxidized in situ using tert-butyl hydroperoxide (TBHP) to afford cyclic epoxy alcohols in high yield (84–87%). PMID:17249767

  18. Highly concentrated catalytic asymmetric allylation of ketones.

    PubMed

    Wooten, Alfred J; Kim, Jeung Gon; Walsh, Patrick J

    2007-02-01

    [reaction: see text] We report the catalytic asymmetric allylation of ketones under highly concentrated reaction conditions with a catalyst generated from titanium tetraisopropoxide and BINOL (1:2 ratio) in the presence of isopropanol. This catalyst promotes the addition of tetraallylstannane to a variety of ketones to produce tertiary homoallylic alcohols in excellent yield (80-99%) with high enantioselectivities (79-95%). The resulting homoallylic alcohols can also be epoxidized in situ using tert-butyl hydroperoxide (TBHP) to afford cyclic epoxy alcohols in high yield (84-87%).

  19. Self-Esteem and Academic Achievement of High School Students

    ERIC Educational Resources Information Center

    Moradi Sheykhjan, Tohid; Jabari, Kamran; Rajeswari, K.

    2014-01-01

    The primary purpose of this study was to determine the influence of self-esteem on academic achievement among high school students in Miandoab City of Iran. The methodology of the research is descriptive and correlation that descriptive and inferential statistics were used to analyze the data. Statistical Society includes male and female high…

  20. Comparison of Achievement of Students in High School Courses

    ERIC Educational Resources Information Center

    Troxel, Verne A.

    1970-01-01

    Compares student achievements on common objectives of CHEMS, CBA, and "Modern Chemistry high school chemistry courses. Results indicate the three couses are not equally effective in meeting their objectives. CHEMS and CBA develop a better understanding of chemistry and science, as well as develop greater ability for critical thinking. CBA…

  1. Relationship between High School Leadership Team Practices and Student Achievement

    ERIC Educational Resources Information Center

    McInnis, Timothy M.

    2009-01-01

    This study investigated if a relationship existed between student achievement in 10th grade Missouri Assessment Program mathematics and 11th grade communication arts scores in 2007 and high school leadership team perceptions of the extent to which they demonstrated leadership practices. The secondary purpose was to compare perceptional…

  2. Early College High School: Closing the Latino Achievement Gap

    ERIC Educational Resources Information Center

    Beall, Kristen Ann

    2016-01-01

    The population of United States Latino students is growing at a rapid rate but their academic achievement lags behind white and Asian students. This issue has significant consequences for the nation's economy, as the job market continues to demand more education and better skills. Early College High School programs have the potential to improve…

  3. DOE High Performance Concentrator PV Project

    SciTech Connect

    McConnell, R.; Symko-Davies, M.

    2005-08-01

    Much in demand are next-generation photovoltaic (PV) technologies that can be used economically to make a large-scale impact on world electricity production. The U.S. Department of Energy (DOE) initiated the High-Performance Photovoltaic (HiPerf PV) Project to substantially increase the viability of PV for cost-competitive applications so that PV can contribute significantly to both our energy supply and environment. To accomplish such results, the National Center for Photovoltaics (NCPV) directs in-house and subcontracted research in high-performance polycrystalline thin-film and multijunction concentrator devices with the goal of enabling progress of high-efficiency technologies toward commercial-prototype products. We will describe the details of the subcontractor and in-house progress in exploring and accelerating pathways of III-V multijunction concentrator solar cells and systems toward their long-term goals. By 2020, we anticipate that this project will have demonstrated 33% system efficiency and a system price of $1.00/Wp for concentrator PV systems using III-V multijunction solar cells with efficiencies over 41%.

  4. Parent Involvement Practices of High-Achieving Elementary Science Students

    NASA Astrophysics Data System (ADS)

    Waller, Samara Susan

    This study addressed a prevalence of low achievement in science courses in an urban school district in Georgia. National leaders and educators have identified the improvement of science proficiency as critical to the future of American industry. The purpose of this study was to examine parent involvement in this school district and its contribution to the academic achievement of successful science students. Social capital theory guided this study by suggesting that students achieve best when investments are made into their academic and social development. A collective case study qualitative research design was used to interview 9 parent participants at 2 elementary schools whose children scored in the exceeds category on the Science CRCT. The research questions focused on what these parents did at home to support their children's academic achievement. Data were collected using a semi-structured interview protocol and analyzed through the categorical aggregation of transcribed interviews. Key findings revealed that the parents invested time and resources in 3 practices: communicating high expectations, supporting and developing key skills, and communicating with teachers. These findings contribute to social change at both the local and community level by creating a starting point for teachers, principals, and district leaders to reexamine the value of parent input in the educational process, and by providing data to support the revision of current parent involvement policies. Possibilities for further study building upon the findings of this study may focus on student perceptions of their parents' parenting as it relates to their science achievement.

  5. The Construction of Black High-Achiever Identities in a Predominantly White High School

    ERIC Educational Resources Information Center

    Andrews, Dorinda J. Carter

    2009-01-01

    In this article, I examine how black students construct their racial and achievement self-concepts in a predominantly white high school to enact a black achiever identity. By listening to these students talk about the importance of race and achievement to their lives, I came to understand how racialized the task of achieving was for them even…

  6. Concentric Tube Robots as Steerable Needles: Achieving Follow-the-Leader Deployment.

    PubMed

    Gilbert, Hunter B; Neimat, Joseph; Webster, Robert J

    2015-04-01

    Concentric tube robots can enable new clinical interventions if they are able to pass through soft tissue, deploy along desired paths through open cavities, or travel along winding lumens. These behaviors require the robot to deploy in such a way that the curved shape of its shaft remains unchanged as the tip progresses forward (i.e., "follow-the-leader" deployment). Follow-the-leader deployment is challenging for concentric tube robots due to elastic (and particularly torsional) coupling between the tubes that form the robot. However, as we show in this paper, follow-the-leader deployment is possible, provided that tube precurvatures and deployment sequences are appropriately selected. We begin by defining follow-the-leader deployment and providing conditions that must be satisfied for a concentric tube robot to achieve it. We then examine several useful special cases of follow-the-leader deployment, showing that both circular and helical precurvatures can be employed, and provide an experimental illustration of the helical case. We also explore approximate follow-the-leader behavior and provide a metric for the similarity of a general deployment to a follow-the-leader deployment. Finally, we consider access to the hippocampus in the brain to treat epilepsy, as a motivating clinical example for follow-the-leader deployment.

  7. Concentric Tube Robots as Steerable Needles: Achieving Follow-the-Leader Deployment

    PubMed Central

    Gilbert, Hunter B.; Neimat, Joseph; Webster, Robert J.

    2015-01-01

    Concentric tube robots can enable new clinical interventions if they are able to pass through soft tissue, deploy along desired paths through open cavities, or travel along winding lumens. These behaviors require the robot to deploy in such a way that the curved shape of its shaft remains unchanged as the tip progresses forward (i.e., “follow-the-leader” deployment). Follow-the-leader deployment is challenging for concentric tube robots due to elastic (and particularly torsional) coupling between the tubes that form the robot. However, as we show in this paper, follow-the-leader deployment is possible, provided that tube precurvatures and deployment sequences are appropriately selected. We begin by defining follow-the-leader deployment and providing conditions that must be satisfied for a concentric tube robot to achieve it. We then examine several useful special cases of follow-the-leader deployment, showing that both circular and helical precurvatures can be employed, and provide an experimental illustration of the helical case. We also explore approximate follow-the-leader behavior and provide a metric for the similarity of a general deployment to a follow-the-leader deployment. Finally, we consider access to the hippocampus in the brain to treat epilepsy, as a motivating clinical example for follow-the-leader deployment. PMID:26622208

  8. Improving science achievement at high-poverty urban middle schools

    NASA Astrophysics Data System (ADS)

    Ruby, Allen

    2006-11-01

    A large percentage of U.S. students attending high-poverty urban middle schools achieve low levels of science proficiency, posing significant challenges to their success in high school science and to national and local efforts to reform science education. Through its work in Philadelphia schools, the Center for Social Organization of Schools at Johns Hopkins University developed a teacher-support model to address variation in science curricula, lack of materials, and underprepared teachers that combined with initial low levels of proficiency block improvements in science achievement. The model includes a common science curriculum based on NSF-supported materials commercially available, ongoing teacher professional development built around day-to-day lessons, and regular in-class support of teachers by expert peer coaches. One cohort of students at three Philadelphia middle schools using the model was followed from the end of fourth grade through seventh grade. Their gains in science achievement and achievement levels were substantially greater than students at 3 matched control schools and the 23 district middle schools serving a similar student population. Under school-by-school comparisons, these results held for the two schools with adequate implementation. Using widely available materials and techniques, the model can be adopted and modified by school partners and districts.

  9. The Will to Achieve: A Phenomenological Study of the Experiences of African American High Achieving Students and Their Parents

    ERIC Educational Resources Information Center

    Spencer, Natalie Faye

    2012-01-01

    The purpose of this research study was to understand the experiences of high achieving African American students and their parents. The experiences of high achieving African American students and their parents have been missing from literature on the academic achievement of African American students. Much of the literature that has been published…

  10. High-efficiency silicon concentrator cell commercialization

    SciTech Connect

    Sinton, R.A.; Swanson, R.M.

    1993-05-01

    This report summarizes the first phase of a forty-one month program to develop a commercial, high-efficiency concentrator solar cell and facility for manufacturing it. The period covered is November 1, 1990 to December 31, 1991. This is a joint program between the Electric Power Research Institute (EPRI) and Sandia National Laboratories. (This report is also published by EPRI as EPRI report number TR-102035.) During the first year of the program, SunPower accomplished the following major objectives: (1) a new solar cell fabrication facility, which is called the Cell Pilot Line (CPL), (2) a baseline concentrator cell process has been developed, and (3) a cell testing facility has been completed. Initial cell efficiencies are about 23% for the baseline process. The long-range goal is to improve this efficiency to 27%.

  11. Thin photovoltaic modules at ultra high concentration

    NASA Astrophysics Data System (ADS)

    Pérez-Higueras, Pedro; Ferrer-Rodríguez, Juan Pablo; Shanks, Katie; Almonacid, Florencia; Férnández, Eduardo F.

    2015-09-01

    A new design concept of high concentration photovoltaic (HCPV) module is studied both by ray-tracing simulation and by building a prototype. This set-up is based on the idea of concentrating sunlight from different optical units to a single commercial multi-junction solar cell, which is located in a different plane than that of the primary optics (e.g. Fresnel lenses). A two-optical-unit set-up, as a first approach, is built and measured with the solar simulator "Helios 3198". These results are compared to the measurement results of the single-unit of one Fresnel lens and the same solar cell. The feasibility of this new design has been confirmed theoretically and practically.

  12. Achieving High Performance on the i860 Microprocessor

    NASA Technical Reports Server (NTRS)

    Lee, King; Kutler, Paul (Technical Monitor)

    1998-01-01

    The i860 is a high performance microprocessor used in the Intel Touchstone project. This paper proposes a paradigm for programming the i860 that is modelled on the vector instructions of the Cray computers. Fortran callable assembler subroutines were written that mimic the concurrent vector instructions of the Cray. Cache takes the place of vector registers. Using this paradigm we have achieved twice the performance of compiled code on a traditional solve.

  13. Experiences of High-Achieving High School Students Who Have Taken Multiple Concurrent Advanced Placement Courses

    ERIC Educational Resources Information Center

    Milburn, Kristine M.

    2011-01-01

    Problem: An increasing number of high-achieving American high school students are enrolling in multiple Advanced Placement (AP) courses. As a result, high schools face a growing need to understand the impact of taking multiple AP courses concurrently on the social-emotional lives of high-achieving students. Procedures: This phenomenological…

  14. Achieving concentrated graphene dispersions in water/acetone mixtures by the strategy of tailoring Hansen solubility parameters

    NASA Astrophysics Data System (ADS)

    Yi, Min; Shen, Zhigang; Zhang, Xiaojing; Ma, Shulin

    2013-01-01

    Although exfoliating graphite to give graphene paves a new way for graphene preparation, a general strategy of low-boiling-point solvents and high graphene concentration is still highly required. In this study, using the strategy of tailoring Hansen solubility parameters (HSP), a method based on exfoliation of graphite in water/acetone mixtures is demonstrated to achieve concentrated graphene dispersions. It is found that in the scope of blending two mediocre solvents, tailoring the HSP of water/acetone mixtures to approach the HSP of graphene could yield graphene dispersions at a high concentration of up to 0.21 mg ml-1. The experimentally determined optimum composition of the mixtures occurs at an acetone mass fraction of ˜75%. The trend of concentration varying with mixture compositions could be well predicated by the model, which relates the concentration to the mixing enthalpy within the scope of HSP theory. The resultant dispersion is highly stabilized. Atomic force microscopic statistical analysis shows that up to ˜50% of the prepared nanosheets are less than 1 nm thick after 4 h sonication and 114g centrifugation. Analyses based on diverse characterizations indicate the graphene sheets to be largely free of basal plane defects and oxidation. The filtered films are also investigated in terms of their electrical and optical properties to show reasonable conductivity and transparency. The strategy of tailoring HSP, which can be easily extended to various solvent systems, and water/acetone mixtures here, extends the scope for large-scale production of graphene in low-boiling-point solutions.

  15. High concentration biotherapeutic formulation and ultrafiltration: Part 1 pressure limits.

    PubMed

    Lutz, Herb; Arias, Joshua; Zou, Yu

    2017-01-01

    High therapeutic dosage requirements and the desire for ease of administration drive the trend to subcutaneous administration using delivery systems such as subcutaneous pumps and prefilled syringes. Because of dosage volume limits, prefilled syringe administration requires higher concentration liquid formulations, limited to about 30 cP or roughly 100-300 g L(-1) for mAb's. Ultrafiltration (UF) processes are routinely used to formulate biological therapeutics. This article considers pressure constraints on the UF process that may limit its ability to achieve high final product concentrations. A system hardware analysis shows that the ultrafiltration cassette pressure drop is the major factor limiting UF systems. Additional system design recommendations are also provided. The design and performance of a new cassette with a lower feed channel flow resistance is described along with 3D modeling of feed channel pressure drop. The implications of variations in cassette flow channel resistance for scaling up and setting specifications are considered. A recommendation for a maximum pressure specification is provided. A review of viscosity data and theory shows that molecular engineering, temperature, and the use of viscosity modifying excipients including pH adjustment can be used to achieve higher concentrations. The combined use of a low pressure drop cassette with excipients further increased final concentrations by 35%. Guidance is provided on system operation to control hydraulics during final concentration. These recommendations should allow one to design and operate systems to routinely achieve the 30 cP target final viscosity capable of delivery using a pre-filled syringe. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 33:113-124, 2017.

  16. Improved Dispersion of Carbon Nanotubes in Polymers at High Concentrations

    PubMed Central

    Liu, Chao-Xuan; Choi, Jin-Woo

    2012-01-01

    The polymer nanocomposite used in this work comprises elastomer poly(dimethylsiloxane) (PDMS) as a polymer matrix and multi-walled carbon nanotubes (MWCNTs) as a conductive nanofiller. To achieve uniform distribution of carbon nanotubes within the polymer, an optimized dispersion process was developed, featuring a strong organic solvent—chloroform, which dissolved PDMS base polymer easily and allowed high quality dispersion of MWCNTs. At concentrations as high as 9 wt.%, MWCNTs were dispersed uniformly through the polymer matrix, which presented a major improvement over prior techniques. The dispersion procedure was optimized via extended experimentation, which is discussed in detail.

  17. Ammonia Solubility in High Concentration Salt Solutions

    SciTech Connect

    HEDENGREN, D.C.

    2000-02-01

    Solubility data for ammonia in water and various dilute solutions are abundant in the literature. However, there is a noticeable lack of ammonia solubility data for high salt, basic solutions of various mixtures of salts including those found in many of the Hanford Washington underground waste tanks. As a result, models based on solubility data for dilute salt solutions have been used to extrapolate to high salt solutions. These significant extrapolations need to be checked against actual laboratory data. Some indirect vapor measurements have been made. A more direct approach is to determine the ratio of solubility of ammonia in water to its solubility in high salt solutions. In various experiments, pairs of solutions, one of which is water and the other a high salt solution, are allowed to come to equilibrium with a common ammonia vapor pressure. The ratio of concentrations of ammonia in the two solutions is equal to the ratio of the respective ammonia solubilities (Henry's Law constants) at a given temperature. This information can then be used to refine the models that predict vapor space compositions of ammonia. Ammonia at Hanford is of concern because of its toxicity in the environment and its contribution to the flammability of vapor space gas mixtures in waste tanks.

  18. Interface Strategy To Achieve Tunable High Frequency Attenuation.

    PubMed

    Lv, Hualiang; Zhang, Haiqian; Ji, Guangbin; Xu, Zhichuan J

    2016-03-01

    Among all polarizations, the interface polarization effect is the most effective, especially at high frequency. The design of various ferrite/iron interfaces can significantly enhance the materials' dielectric loss ability at high frequency. This paper presents a simple method to generate ferrite/iron interfaces to enhance the microwave attenuation at high frequency. The ferrites were coated onto carbonyl iron and could be varied to ZnFe2O4, CoFe2O4, Fe3O4, and NiFe2O4. Due to the ferrite/iron interface inducing a stronger dielectric loss effect, all of these materials achieved broad effective frequency width at a coating layer as thin as 1.5 mm. In particular, an effective frequency width of 6.2 GHz could be gained from the Fe@NiFe2O4 composite.

  19. Diverse microbial species survive high ammonia concentrations

    NASA Astrophysics Data System (ADS)

    Kelly, Laura C.; Cockell, Charles S.; Summers, Stephen

    2012-04-01

    Planetary protection regulations are in place to control the contamination of planets and moons with terrestrial micro-organisms in order to avoid jeopardizing future scientific investigations relating to the search for life. One environmental chemical factor of relevance in extraterrestrial environments, specifically in the moons of the outer solar system, is ammonia (NH3). Ammonia is known to be highly toxic to micro-organisms and may disrupt proton motive force, interfere with cellular redox reactions or cause an increase of cell pH. To test the survival potential of terrestrial micro-organisms exposed to such cold, ammonia-rich environments, and to judge whether current planetary protection regulations are sufficient, soil samples were exposed to concentrations of NH3 from 5 to 35% (v/v) at -80°C and room temperature for periods up to 11 months. Following exposure to 35% NH3, diverse spore-forming taxa survived, including representatives of the Firmicutes (Bacillus, Sporosarcina, Viridibacillus, Paenibacillus, Staphylococcus and Brevibacillus) and Actinobacteria (Streptomyces). Non-spore forming organisms also survived, including Proteobacteria (Pseudomonas) and Actinobacteria (Arthrobacter) that are known to have environmentally resistant resting states. Clostridium spp. were isolated from the exposed soil under anaerobic culture. High NH3 was shown to cause a reduction in viability of spores over time, but spore morphology was not visibly altered. In addition to its implications for planetary protection, these data show that a large number of bacteria, potentially including spore-forming pathogens, but also environmentally resistant non-spore-formers, can survive high ammonia concentrations.

  20. Unlocking Emergent Talent: Supporting High Achievement of Low-Income, High Ability Students

    ERIC Educational Resources Information Center

    Olszewski-Kubilius, Paula; Clarenbach, Jane

    2012-01-01

    This report takes a comprehensive look at achievement for low-income promising learners--past, present, and future. At its core, it challenges the nation to move beyond its near-singular focus of achieving minimum performance for all students, to identifying and developing the talent of all students who are capable of high achievement, including…

  1. Behaviour and achievement disorders in children with high intelligence.

    PubMed

    Barchmann, H; Kinze, W

    1990-01-01

    With 6% of the patients of a childpsychiatric population using treatment a high intelligence with an IQ of over 120 was the result. This is in agreement with the results by Reinhard (1981), but is below the results by Schmidt (1977) and justifies neither the association to a higher talent as risk factor nor as protective factor in view of a potential psychic illness. 341 child-neuropsychiatric patients with hyperkinetic syndrome (55%), Enuresis (28%), reactions of adaptation (5%), specific emotional disturbances in childhood (4%), Encopresis (3%), Psychalgy (3%) and tics (2%) were studied; thereby 22 highly intelligent patients were compared with average intelligent patients. With high intelligence better performances of concentration, more reflexive style of study, better school notes and more favourable motor capabilities, less pronounced signs of anxiety and neuroticism are found, but also a poorer social adaptation and less favourable effects of treatment. Concerning the poorer chances of treatment with high intelligence however the behaviour-therapeutic concentration of our therapy has to be pointed out, which might not offer an optimal chance for development.

  2. Concentrating solar power in Europe, the Middle East and North Africa: achieving its potential

    NASA Astrophysics Data System (ADS)

    Pitz-Paal, R.; Amin, A.; Bettzüge, M.; Eames, P.; Fabrizi, F.; Flamant, G.; Garcia Novo, F.; Holmes, J.; Kribus, A.; van der Laan, H.; Lopez, C.; Papagiannakopoulos, P.; Pihl, E.; Smith, P.; Wagner, H.-J.

    2012-10-01

    Concentrating solar power (CSP) is a commercially available renewable energy technology capable of harnessing the immense solar resource in Southern Europe, the Middle East and North Africa (the MENA region), and elsewhere. This paper summarises the findings of a study by the European Academies Science Advisory Council which has examined the current status and development challenges of CSP, and consequently has evaluated the potential contribution of CSP in Europe and the MENA region to 2050. It identifies the actions that will be required by scientists, engineers, policy makers, politicians, business and investors alike, to enable this vast solar resource to make a major contribution to establishing a sustainable energy system. The study concludes that cost reductions of 50-60% in CSP electricity may reasonably be expected in the next 10-15 years, enabling the technology to be cost competitive with fossil-fired power generation at some point between 2020 and 2030. Incorporation of storage delivers added value in enabling CSP to deliver dispatchable power. Incentive schemes will be needed in Europe and MENA countries to enable this point to be achieved. Such schemes should reflect the true value of electricity to the grid, effectively drive R&D, and ensure transparency of performance and cost data.

  3. Achieving unusual oxidation state of matter under high pressure

    NASA Astrophysics Data System (ADS)

    Wang, Xiaoli; Lin, Haiqing; Ma, Yanming; Miao, Maosheng

    2013-03-01

    Pressure has many effects to matter including the reduction of the volume, the increase of the coordination number and the broadening of the band-widths. In the past, most of the high-pressure studies focused on structural and electronic state phase transitions. Using first principles calculations and a bias-free structural search method, we will demonstrate that high pressure can lead to high oxidation state of elements that can never be achieved under ambient condition, making high pressure technique a nice tool to explore many traditional topics in solid state and molecular chemistry. As an example, we will show that Hg can transfer the electrons in its outmost d shell to F atoms and form HgF4 molecular crystals under pressure, thereby acting as a true transition metal. Group IIB elements, including Zn, Cd, and Hg are usually defined as post-transition metals because they are commonly oxidized only to the +2 state. Their d shells are completely filled and do not participate in the formation of chemical bonds. Although the synthesis of HgF4 molecules in gas phase was reported before, the molecules show strong instabilities and dissociate. Therefore, the transition metal propensity of Hg remains an open question.

  4. Achieving high energy absorption capacity in cellular bulk metallic glasses

    PubMed Central

    Chen, S. H.; Chan, K. C.; Wu, F. F.; Xia, L.

    2015-01-01

    Cellular bulk metallic glasses (BMGs) have exhibited excellent energy-absorption performance by inheriting superior strength from the parent BMGs. However, how to achieve high energy absorption capacity in cellular BMGs is vital but mysterious. In this work, using step-by-step observations of the deformation evolution of a series of cellular BMGs, the underlying mechanisms for the remarkable energy absorption capacity have been investigated by studying two influencing key factors: the peak stress and the decay of the peak stress during the plastic-flow plateau stages. An analytical model of the peak stress has been proposed, and the predicted results agree well with the experimental data. The decay of the peak stress has been attributed to the geometry change of the macroscopic cells, the formation of shear bands in the middle of the struts, and the “work-softening” nature of BMGs. The influencing factors such as the effect of the strut thickness and the number of unit cells have also been investigated and discussed. Strategies for achieving higher energy absorption capacity in cellular BMGs have been proposed. PMID:25973781

  5. Achieving High Resolution Timer Events in Virtualized Environment

    PubMed Central

    Adamczyk, Blazej; Chydzinski, Andrzej

    2015-01-01

    Virtual Machine Monitors (VMM) have become popular in different application areas. Some applications may require to generate the timer events with high resolution and precision. This however may be challenging due to the complexity of VMMs. In this paper we focus on the timer functionality provided by five different VMMs—Xen, KVM, Qemu, VirtualBox and VMWare. Firstly, we evaluate resolutions and precisions of their timer events. Apparently, provided resolutions and precisions are far too low for some applications (e.g. networking applications with the quality of service). Then, using Xen virtualization we demonstrate the improved timer design that greatly enhances both the resolution and precision of achieved timer events. PMID:26177366

  6. Achievement of high nitrite accumulation via endogenous partial denitrification (EPD).

    PubMed

    Ji, Jiantao; Peng, Yongzhen; Wang, Bo; Wang, Shuying

    2017-01-01

    This study proposed a novel strategy for achievement of partial denitrification driven by endogenous carbon sources in an anaerobic/anoxic/aerobic activated sludge system. Results showed that in the steady-stage, the nitrate-to-nitrite transformation ratio (NTR) was kept at around 87% without nitrate in the effluent. During the anaerobic period, exogenous carbon sources was completely taken up, accompanied by the consumption of glycogen and production of polyhydroxyalkanoates (PHAs). During the anoxic period, nitrate was reduced to nitrite by using PHAs as carbon sources, followed by the replenishment of glycogen. Thus, the phenotype of denitrifying GAOs was clearly observed and endogenous partial denitrification (EPD) occurred. Furthermore, results showed the nitrate reduction was prior to the nitrite reduction in the presence of nitrate, which led to the high nitrite accumulation.

  7. Achieving environmentally relevant organochlorine pesticide concentrations in eggs through maternal exposure in Alligator mississippiensis

    USGS Publications Warehouse

    Rauschenberger, R.H.; Wiebe, J.J.; Buckland, J.E.; Smith, Joe T.; Sepulveda, M.S.; Gross, T.S.

    2004-01-01

    Alligator mississippiensis eggs from organochlorine pesticide (OCP) contaminated sites in Florida exhibit high rates of embryonic mortality compared to reference sites (p<0.05). The objective of the present study was to use captive adult alligators to test the hypotheses that maternal exposure to OCPs results in increased OCP concentrations in eggs, and that increased exposure is associated with increased embryonic mortality. A total of 24 adult alligators (8 males and 16 females) were housed in eight pens. Eight females in four pens were dosed with a mixture of p,p'-DDE, toxaphene, dieldrin, and chlordane at a rate of 0.2 ? 0.01 mg/kg/day for 274 ? 8 days. Treated females produced eggs containing higher OCP concentrations (12,814 ? 813 ng/g yolk) than controls (38 ? 4 ng/g yolk). Eggs of treated females exhibited decreased viability (13 ? 22%) as compared to controls (45 ? 20%). Results indicated that 0.6% of administered OCPs were maternally transferred to the eggs of American alligators, and that maternal exposure is associated with decreased egg/embryo viability in this species.

  8. Europium doped lanthanum zirconate nanoparticles with high concentration quenching

    SciTech Connect

    Alaparthi, Suresh B.; Lu, Long; Tian, Yue; Mao, Yuanbing

    2014-01-01

    Graphical abstract: - Highlights: • Eu:La{sub 2}Zr{sub 2}O{sub 7} nanoparticles were prepared facilely by a kinetically modified molten salt method. • High color purity and concentration quenching were achieved in these La{sub 2}Zr{sub 2}O{sub 7}:Eu nanoparticles. • Concentration quenching mechanism was discussed for Eu{sup 3+} in these Eu:La{sub 2}Zr{sub 2}O{sub 7} nanoparticles. - Abstract: A series of Eu{sup 3+} doped lanthanum zirconate (La{sub 2}Zr{sub 2}O{sub 7}) nanoparticles (NPs, 20 ± 5 nm in diameter) with cubic fluorite structure were facilely synthesized by a kinetically modified molten salt synthetic (MSS) process and characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and photoluminescence spectra (PL). Under the excitation of 405 nm, intense red emission with high color purity can be observed in the Eu{sup 3+} doped La{sub 2}Zr{sub 2}O{sub 7} NPs. Moreover, the as-prepared Eu:La{sub 2}Zr{sub 2}O{sub 7} NPs possess high concentration quenching, which is as high as ∼32.5 mol% of europium dopants in the La{sub 2}Zr{sub 2}O{sub 7} host. The corresponding concentration quenching mechanism was discussed as well. Our results confirm that the kinetically modified MSS process is a promising approach for preparing rare earth (RE) ions doped A{sub 2}B{sub 2}O{sub 7} nanoparticles with uniform RE doping and high concentration quenching.

  9. Achieving ultra-high temperatures with a resistive emitter array

    NASA Astrophysics Data System (ADS)

    Danielson, Tom; Franks, Greg; Holmes, Nicholas; LaVeigne, Joe; Matis, Greg; McHugh, Steve; Norton, Dennis; Vengel, Tony; Lannon, John; Goodwin, Scott

    2016-05-01

    The rapid development of very-large format infrared detector arrays has challenged the IR scene projector community to also develop larger-format infrared emitter arrays to support the testing of systems incorporating these detectors. In addition to larger formats, many scene projector users require much higher simulated temperatures than can be generated with current technology in order to fully evaluate the performance of their systems and associated processing algorithms. Under the Ultra High Temperature (UHT) development program, Santa Barbara Infrared Inc. (SBIR) is developing a new infrared scene projector architecture capable of producing both very large format (>1024 x 1024) resistive emitter arrays and improved emitter pixel technology capable of simulating very high apparent temperatures. During earlier phases of the program, SBIR demonstrated materials with MWIR apparent temperatures in excess of 1400 K. New emitter materials have subsequently been selected to produce pixels that achieve even higher apparent temperatures. Test results from pixels fabricated using the new material set will be presented and discussed. A 'scalable' Read In Integrated Circuit (RIIC) is also being developed under the same UHT program to drive the high temperature pixels. This RIIC will utilize through-silicon via (TSV) and Quilt Packaging (QP) technologies to allow seamless tiling of multiple chips to fabricate very large arrays, and thus overcome the yield limitations inherent in large-scale integrated circuits. Results of design verification testing of the completed RIIC will be presented and discussed.

  10. How to achieve high-level expression of microbial enzymes

    PubMed Central

    Liu, Long; Yang, Haiquan; Shin, Hyun-dong; Chen, Rachel R.; Li, Jianghua; Du, Guocheng; Chen, Jian

    2013-01-01

    Microbial enzymes have been used in a large number of fields, such as chemical, agricultural and biopharmaceutical industries. The enzyme production rate and yield are the main factors to consider when choosing the appropriate expression system for the production of recombinant proteins. Recombinant enzymes have been expressed in bacteria (e.g., Escherichia coli, Bacillus and lactic acid bacteria), filamentous fungi (e.g., Aspergillus) and yeasts (e.g., Pichia pastoris). The favorable and very advantageous characteristics of these species have resulted in an increasing number of biotechnological applications. Bacterial hosts (e.g., E. coli) can be used to quickly and easily overexpress recombinant enzymes; however, bacterial systems cannot express very large proteins and proteins that require post-translational modifications. The main bacterial expression hosts, with the exception of lactic acid bacteria and filamentous fungi, can produce several toxins which are not compatible with the expression of recombinant enzymes in food and drugs. However, due to the multiplicity of the physiological impacts arising from high-level expression of genes encoding the enzymes and expression hosts, the goal of overproduction can hardly be achieved, and therefore, the yield of recombinant enzymes is limited. In this review, the recent strategies used for the high-level expression of microbial enzymes in the hosts mentioned above are summarized and the prospects are also discussed. We hope this review will contribute to the development of the enzyme-related research field. PMID:23686280

  11. Effects of Partner's Ability on the Achievement and Conceptual Organization of High-Achieving Fifth-Grade Students.

    ERIC Educational Resources Information Center

    Carter, Glenda; Jones, M. Gail; Rua, Melissa

    2003-01-01

    Investigates high-achieving fifth-grade students' achievement gains and conceptual reorganization on convection. Features an instructional sequence of three dyadic inquiry investigations related to convection currents as well as pre- and post-assessment consisting of a multiple-choice test, a card sorting task, construction of a concept map, and…

  12. Comparison of the Level of Using Metacognitive Strategies during Study between High Achieving and Low Achieving Prospective Teachers

    ERIC Educational Resources Information Center

    Doganay, Ahmet; Demir, Ozden

    2011-01-01

    The main purpose of this study is to compare the level of using metacognitive strategies during study between high achieving and low achieving prospective classroom teachers. This study was designed as a mixed method study. Metacognitive Learning Strategies Scale developed by Namlu (2004) was used to measure the use of metacognitive strategies…

  13. Molecular basis of high viscosity in concentrated antibody solutions: Strategies for high concentration drug product development

    PubMed Central

    Tomar, Dheeraj S.; Kumar, Sandeep; Singh, Satish K.; Goswami, Sumit; Li, Li

    2016-01-01

    ABSTRACT Effective translation of breakthrough discoveries into innovative products in the clinic requires proactive mitigation or elimination of several drug development challenges. These challenges can vary depending upon the type of drug molecule. In the case of therapeutic antibody candidates, a commonly encountered challenge is high viscosity of the concentrated antibody solutions. Concentration-dependent viscosity behaviors of mAbs and other biologic entities may depend on pairwise and higher-order intermolecular interactions, non-native aggregation, and concentration-dependent fluctuations of various antibody regions. This article reviews our current understanding of molecular origins of viscosity behaviors of antibody solutions. We discuss general strategies and guidelines to select low viscosity candidates or optimize lead candidates for lower viscosity at early drug discovery stages. Moreover, strategies for formulation optimization and excipient design are also presented for candidates already in advanced product development stages. Potential future directions for research in this field are also explored. PMID:26736022

  14. Molecular basis of high viscosity in concentrated antibody solutions: Strategies for high concentration drug product development.

    PubMed

    Tomar, Dheeraj S; Kumar, Sandeep; Singh, Satish K; Goswami, Sumit; Li, Li

    2016-01-01

    Effective translation of breakthrough discoveries into innovative products in the clinic requires proactive mitigation or elimination of several drug development challenges. These challenges can vary depending upon the type of drug molecule. In the case of therapeutic antibody candidates, a commonly encountered challenge is high viscosity of the concentrated antibody solutions. Concentration-dependent viscosity behaviors of mAbs and other biologic entities may depend on pairwise and higher-order intermolecular interactions, non-native aggregation, and concentration-dependent fluctuations of various antibody regions. This article reviews our current understanding of molecular origins of viscosity behaviors of antibody solutions. We discuss general strategies and guidelines to select low viscosity candidates or optimize lead candidates for lower viscosity at early drug discovery stages. Moreover, strategies for formulation optimization and excipient design are also presented for candidates already in advanced product development stages. Potential future directions for research in this field are also explored.

  15. Athletic Activity and Hormone Concentrations in High School Female Athletes

    PubMed Central

    Wojtys, Edward M.; Jannausch, Mary L.; Kreinbrink, Jennifer L.; Harlow, Siobán D.; Sowers, MaryFran R.

    2015-01-01

    Context: Physical activity may affect the concentrations of circulating endogenous hormones in female athletes. Understanding the relationship between athletic and physical activity and circulating female hormone concentrations is critical. Objective: To test the hypotheses that (1) the estradiol-progesterone profile of high school adolescent girls participating in training, conditioning, and competition would differ from that of physically inactive, age-matched adolescent girls throughout a 3-month period; and (2) athletic training and conditioning would alter body composition (muscle, bone), leading to an increasingly greater lean–body-mass to fat–body-mass ratio with accompanying hormonal changes. Design: Cohort study. Settings: Laboratory and participants' homes. Patients or Other Participants: A total of 106 adolescent girls, ages 14–18 years, who had experienced at least 3 menstrual cycles in their lifetime. Main Outcome Measure(s): Participants were prospectively monitored throughout a 13-week period, with weekly physical activity assessments and 15 urine samples for estrogen, luteinizing hormone, creatinine, and progesterone concentrations. Each girl underwent body-composition measurements before and after the study period. Results: Seventy-four of the 98 girls (76%) who completed the study classified themselves as athletes. Body mass index, body mass, and fat measures remained stable, and 17 teenagers had no complete menstrual cycle during the observation period. Mean concentrations of log(estrogen/creatinine) were slightly greater in nonathletes who had cycles of <24 or >35 days. Mean log(progesterone/creatinine) concentrations in nonathletes were less in the first half and greater in the second half of the cycle, but the differences were not statistically significant. Conclusions: A moderate level of athletic or physical activity did not influence urine concentrations of estrogen, progesterone, or luteinizing hormones. However, none of the

  16. Biological denitrification of high concentration nitrate waste

    DOEpatents

    Francis, Chester W.; Brinkley, Frank S.

    1977-01-01

    Biological denitrification of nitrate solutions at concentrations of greater than one kilogram nitrate per cubic meter is accomplished anaerobically in an upflow column having as a packing material a support for denitrifying bacteria.

  17. Development of manufacturing capability for high-concentration, high-efficiency silicon solar cells

    SciTech Connect

    Sinton, R.A.; Verlinden, P.J.; Crane, R.A.; Swanson, R.N.

    1996-10-01

    This report presents a summary of the major results from a program to develop a manufacturable, high-efficiency silicon concentrator solar cell and a cost-effective manufacturing facility. The program was jointly funded by the Electric Power Research Institute, Sandia National Laboratories through the Concentrator Initiative, and SunPower Corporation. The key achievements of the program include the demonstration of 26%-efficient silicon concentrator solar cells with design-point (20 W/cm{sup 2}) efficiencies over 25%. High-performance front-surface passivations; that were developed to achieve this result were verified to be absolutely stable against degradation by 475 days of field exposure at twice the design concentration. SunPower demonstrated pilot production of more than 1500 of these cells. This cell technology was also applied to pilot production to supply 7000 17.7-cm{sup 2} one-sun cells (3500 yielded wafers) that demonstrated exceptional quality control. The average efficiency of 21.3% for these cells approaches the peak efficiency ever demonstrated for a single small laboratory cell within 2% (absolute). Extensive cost models were developed through this program and calibrated by the pilot-production project. The production levels achieved indicate that SunPower could produce 7-10 MW of concentrator cells per year in the current facility based upon the cell performance demonstrated during the program.

  18. Achieving High Throughput for Data Transfer over ATM Networks

    NASA Technical Reports Server (NTRS)

    Johnson, Marjory J.; Townsend, Jeffrey N.

    1996-01-01

    File-transfer rates for ftp are often reported to be relatively slow, compared to the raw bandwidth available in emerging gigabit networks. While a major bottleneck is disk I/O, protocol issues impact performance as well. Ftp was developed and optimized for use over the TCP/IP protocol stack of the Internet. However, TCP has been shown to run inefficiently over ATM. In an effort to maximize network throughput, data-transfer protocols can be developed to run over UDP or directly over IP, rather than over TCP. If error-free transmission is required, techniques for achieving reliable transmission can be included as part of the transfer protocol. However, selected image-processing applications can tolerate a low level of errors in images that are transmitted over a network. In this paper we report on experimental work to develop a high-throughput protocol for unreliable data transfer over ATM networks. We attempt to maximize throughput by keeping the communications pipe full, but still keep packet loss under five percent. We use the Bay Area Gigabit Network Testbed as our experimental platform.

  19. Achieving High Rates and High Uniformity in Copper Chemical Mechanical Polishing

    NASA Astrophysics Data System (ADS)

    Nolan, Lucy Marjorie

    The chemical mechanical polishing of Copper (Cu-CMP) is a complex and poorly understood process. Despite this, it is widely used throughout the semiconductor and microelectronics industries, and makes up a significant portion of wafer processing costs. In these contexts, desirable polishing outcomes such as a high rate of removal from the copper surface, and high removal rate uniformity, are achieved largely by trial-and-error. In this study, the same outcomes are pursued through a systematic investigation of polishing lubrication characteristics and abrasive and oxidiser concentrations in the polishing slurry. A strong link between lubrication characteristics, quantified by the dimensionless Sommerfield number, and the uniformity of polishing is demonstrated. A mechanism for the observed relationship is proposed, based on an adaptation of hydrodynamic lubrication theory. The overall rate of removal is maximized by polishing in a slurry containing oxidiser and abrasives in a synergistic ratio. Polishing away from this ratio has additional effects on the overall quality of the surface produced. Transport of slurry across the polishing pad is investigated by using tracers; the results demonstrate that slurry usage can be reduced in many circumstances with no impact on overall polishing outcomes, reducing overall processing costs. These findings are combined to design a polishing process, with good results.

  20. Does Recreational Computer Use Affect High School Achievement?

    ERIC Educational Resources Information Center

    Bowers, Alex J.; Berland, Matthew

    2013-01-01

    Historically, the relationship between student academic achievement and use of computers for fun and video gaming has been described from a multitude of perspectives, from positive, to negative, to neutral. However, recent research has indicated that computer use and video gaming may be positively associated with achievement, yet these studies…

  1. Student Perception of Academic Achievement Factors at High School

    ERIC Educational Resources Information Center

    Bahar, Mustafa

    2016-01-01

    Measuring the quality of the "product" is elemental in education, and most studies depend on observational data about student achievement factors, focusing overwhelmingly on quantitative data namely achievement scores, school data like attendance, facilities, expenditure class size, etc. But there is little evidence of learner…

  2. High-Achieving High School Students and Not so High-Achieving College Students: A Look at Lack of Self-Control, Academic Ability, and Performance in College

    ERIC Educational Resources Information Center

    Honken, Nora B.; Ralston, Patricia A. S.

    2013-01-01

    This study investigated the relationship among lack of self-control, academic ability, and academic performance for a cohort of freshman engineering students who were, with a few exceptions, extremely high achievers in high school. Structural equation modeling analysis led to the conclusion that lack of self-control in high school, as measured by…

  3. Towards operating direct methanol fuel cells with highly concentrated fuel

    NASA Astrophysics Data System (ADS)

    Zhao, T. S.; Yang, W. W.; Chen, R.; Wu, Q. X.

    A significant advantage of direct methanol fuel cells (DMFCs) is the high specific energy of the liquid fuel, making it particularly suitable for portable and mobile applications. Nevertheless, conventional DMFCs have to be operated with excessively diluted methanol solutions to limit methanol crossover and the detrimental consequences. Operation with diluted methanol solutions significantly reduces the specific energy of the power pack and thereby prevents it from competing with advanced batteries. In view of this fact, there exists a need to improve conventional DMFC system designs, including membrane electrode assemblies and the subsystems for supplying/removing reactants/products, so that both the cell performance and the specific energy can be simultaneously maximized. This article provides a comprehensive review of past efforts on the optimization of DMFC systems that operate with concentrated methanol. Based on the discussion of the key issues associated with transport of the reactants/products, the strategies to manage the supply/removal of the reactants/products in DMFC operating with highly concentrated methanol are identified. With these strategies, the possible approaches to achieving the goal of concentrated fuel operation are then proposed. Past efforts in the management of the reactants/products for implementing each of the approaches are also summarized and reviewed.

  4. Optical design considerations for high-concentration photovoltaics

    NASA Astrophysics Data System (ADS)

    Garboushian, Vahan; Gordon, Robert

    2006-08-01

    Over the past 15 years, major advances in Concentrating Photovoltaics (CPV) have been achieved. Ultra-efficient Si solar cells have produced commercial concentration systems which are being fielded today and are competitively priced. Advanced research has primarily focused on significantly more efficient multi-junction solar cells for tomorrow's systems. This effort has produced sophisticated solar cells that significantly improve power production. Additional performance and cost improvements, especially in the optical system area and system integration, must be made before CPV can realize its ultimate commercial potential. Structural integrity and reliability are vital for commercial success. As incremental technical improvements are made in solar cell technologies, evaluation and 'fine-tuning' of optical systems properly matched to the solar cell are becoming increasingly necessary. As we move forward, it is increasingly important to optimize all of the interrelated elements of a CPV system for high performance without sacrificing the marketable cost and structural requirements of the system. Areas such as wavelength absorption of refractive optics need to be carefully matched to the solar cell technology employed. Reflective optics require advanced engineering models to insure uniform flux distribution without excessive losses. In Situ measurement of the 'fine-grain' improvements are difficult as multiple variables such as solar insolation, temperature, wind, altitude, etc. infringe on analytical data. This paper discusses design considerations based on 10 years of field trials of high concentration systems and their relevance for tomorrow's advanced CPV systems.

  5. Threatened and Placed at Risk: High Achieving African American Males in Urban High Schools

    ERIC Educational Resources Information Center

    McGee, Ebony O.

    2013-01-01

    This study investigated the risk and protective factors of 11 high-achieving African American males attending 4 urban charter high schools in a Midwestern city to determine what factors account for their resilience and success in mathematics courses, and in high school more generally. This research was guided by a Phenomenological Variant of…

  6. The Effect of Music Participation on Mathematical Achievement and Overall Academic Achievement of High School Students

    ERIC Educational Resources Information Center

    Cox, H. A.; Stephens, L. J.

    2006-01-01

    A study was conducted on high school students, comparing those with some music credits to those with none. No statistically significant difference was found in their mean math grade point averages (GPA) or their mean cumulative GPAs. Students were then separated into two groups based on the number of music credits. Students who had earned at least…

  7. Busulphan is active against neuroblastoma and medulloblastoma xenografts in athymic mice at clinically achievable plasma drug concentrations

    PubMed Central

    Boland, I; Vassal, G; Morizet, J; Terrier-Lacombe, M-J; Valteau-Couanet, D; Kalifa, C; Hartmann, O; Gouyette, A

    1999-01-01

    High-dose busulphan-containing chemotherapy regimens have shown high response rates in children with relapsed or refractory neuroblastoma, Ewing's sarcoma and medulloblastoma. However, the anti-tumour activity of busulfan as a single agent remains to be defined, and this was evaluated in athymic mice bearing advanced stage subcutaneous paediatric solid tumour xenografts. Because busulphan is highly insoluble in water, the use of several vehicles for enteral and parenteral administration was first investigated in terms of pharmacokinetics and toxicity. The highest bioavailability was obtained with busulphan in DMSO administered i.p. When busulphan was suspended in carboxymethylcellulose and given orally or i.p., the bioavailability was poor. Then, in the therapeutic experiments, busulphan in DMSO was administered i.p. on days 0 and 4. At the maximum tolerated total dose (50 mg kg−1), busulphan induced a significant tumour growth delay, ranging from 12 to 34 days in the three neuroblastomas evaluated and in one out of three medulloblastomas. At a dose level above the maximum tolerated dose, busulphan induced complete and partial tumour regressions. Busulphan was inactive in a peripheral primitive neuroectodermal tumour (PNET) xenograft. When busulphan pharmacokinetics in mice and humans were considered, the estimated systemic exposure at the therapeutically active dose in mice (113 μg h ml−1) was close to the mean total systemic exposure in children receiving high-dose busulphan (102.4 μg h ml−1). In conclusion, busulphan displayed a significant anti-tumour activity in neuroblastoma and medulloblastoma xenografts at plasma drug concentrations which can be achieved clinically in children receiving high-dose busulphan-containing regimens. 1999 Cancer Research Campaign PMID:10070870

  8. Population Pharmacokinetics of Colistin Methanesulfonate in Rats: Achieving Sustained Lung Concentrations of Colistin for Targeting Respiratory Infections

    PubMed Central

    W. S. Yapa, Shalini; Li, Jian; Porter, Christopher J. H.; Nation, Roger L.

    2013-01-01

    Colistin methanesulfonate (CMS), the inactive prodrug of colistin, is administered by inhalation for the management of respiratory infections. However, limited pharmacokinetic data are available for CMS and colistin following pulmonary delivery. This study investigates the pharmacokinetics of CMS and colistin following intravenous (i.v.) and intratracheal (i.t.) administration in rats and determines the targeting advantage after direct delivery into the lungs. In addition to plasma, bronchoalveolar lavage (BAL) fluid was collected to quantify drug concentrations in lung epithelial lining fluid (ELF). The resulting data were analyzed using a population modeling approach in S-ADAPT. A three-compartment model described the disposition of both compounds in plasma following i.v. administration. The estimated mean clearance from the central compartment was 0.122 liters/h for CMS and 0.0657 liters/h for colistin. Conversion of CMS to colistin from all three compartments was required to fit the plasma data. The fraction of the i.v. dose converted to colistin in the systemic circulation was 0.0255. Two BAL fluid compartments were required to reflect drug kinetics in the ELF after i.t. dosing. A slow conversion of CMS (mean conversion time [MCTCMS] = 3.48 h) in the lungs contributed to high and sustained concentrations of colistin in ELF. The fraction of the CMS dose converted to colistin in ELF (fm,ELF = 0.226) was higher than the corresponding fractional conversion in plasma after i.v. administration. In conclusion, pulmonary administration of CMS achieves high and sustained exposures of colistin in lungs for targeting respiratory infections. PMID:23917323

  9. Academic attainment and the high school science experiences among high-achieving African American males

    NASA Astrophysics Data System (ADS)

    Trice, Rodney Nathaniel

    This study examines the educational experiences of high achieving African American males. More specifically, it analyzes the influences on their successful navigation through high school science. Through a series of interviews, observations, questionnaires, science portfolios, and review of existing data the researcher attempted to obtain a deeper understanding of high achieving African American males and their limitations to academic attainment and high school science experiences. The investigation is limited to ten high achieving African American male science students at Woodcrest High School. Woodcrest is situated at the cross section of a suburban and rural community located in the southeastern section of the United States. Although this investigation involves African American males, all of whom are successful in school, its findings should not be generalized to this nor any other group of students. The research question that guided this study is: What are the limitations to academic attainment and the high school science experiences of high achieving African American males? The student participants expose how suspension and expulsion, special education placement, academic tracking, science instruction, and teacher expectation influence academic achievement. The role parents play, student self-concept, peer relationships, and student learning styles are also analyzed. The anthology of data rendered three overarching themes: (1) unequal access to education, (2) maintenance of unfair educational structures, and (3) authentic characterizations of African American males. Often the policies and practices set in place by school officials aid in creating hurdles to academic achievement. These policies and practices are often formed without meaningful consideration of the unintended consequences that may affect different student populations, particularly the most vulnerable. The findings from this study expose that high achieving African American males face major

  10. Dominant Achievement Goals across Tracks in High School

    ERIC Educational Resources Information Center

    Scheltinga, Peter A. M.; Kuyper, Hans; Timmermans, Anneke C.; van der Werf, Greetje P. C.

    2016-01-01

    The dominant achievement goals (DAGs) of 7,008 students in the third grade of Dutch secondary education (US grade 9) were investigated, based on Elliot & McGregors' 2 × 2 framework (2001), in relation to track-level and motivational variables. We found the mastery-approach goal and the performance-approach goal, generally considered adaptive,…

  11. Charter High Schools: Closing the Achievement Gap. Innovations in Education

    ERIC Educational Resources Information Center

    US Department of Education, 2006

    2006-01-01

    The eight schools profiled in this document are serving different populations, but all of them are closing the achievement gap between low-income, minority, and special needs students and their peers. By trying out innovative new strategies, these schools are blazing a trail for others to follow. They are dispelling the myth that some students can…

  12. Parenting Style, Perfectionism, and Creativity in High-Ability and High-Achieving Young Adults

    ERIC Educational Resources Information Center

    Miller, Angie L.; Lambert, Amber D.; Speirs Neumeister, Kristie L.

    2012-01-01

    The current study explores the potential relationships among perceived parenting style, perfectionism, and creativity in a high-ability and high-achieving young adult population. Using data from 323 honors college students at a Midwestern university, bivariate correlations suggested positive relationships between (a) permissive parenting style and…

  13. Success Despite Socioeconomics: A Case Study of a High-Achieving, High-Poverty School

    ERIC Educational Resources Information Center

    Tilley, Thomas Brent; Smith, Samuel J.; Claxton, Russell L.

    2012-01-01

    This case study of a high-achieving, high-poverty school describes the school's leadership, culture, and programs that contributed to its success. Data were collected from two surveys (the School Culture Survey and the Vanderbilt Assessment of Leadership in Education), observations at the school site, and interviews with school personnel. The…

  14. Deficits in cognitive function and achievement in Mexican first-graders with low blood lead concentrations.

    PubMed

    Kordas, Katarzyna; Canfield, Richard L; López, Patricia; Rosado, Jorge L; Vargas, Gonzalo García; Cebrián, Mariano E; Rico, Javier Alatorre; Ronquillo, Dolores; Stoltzfus, Rebecca J

    2006-03-01

    Elevated blood lead levels in children are associated with lower scores on tests of cognitive functioning. Recent studies have reported inverse relations between lifetime exposure and intellectual functioning at blood lead concentrations below 10 microg/dL, the Centers for Disease Control and Prevention's (CDC) level of concern. We report associations between blood lead and cognitive performance for first-grade Mexican children living near a metal foundry. Using a cross-sectional design, we examined the relation between children's concurrent blood lead concentrations (mean (SD) 11.4 microg/dL (6.1)) and their performance on 14 tests of global or specific cognitive functions. The blood lead-cognition relations were modeled using both linear and nonlinear methods. After adjustment for covariates, a higher blood lead level was associated with poorer cognitive performance on several cognitive tests. Segmented linear regressions revealed significant effects of lead but only for the segments defined by a concurrent blood lead concentration below 10-14 microg/dL. One implication of these findings is that at the age of 7 years, even in the absence of information on lead exposure in infancy and early childhood, a test result with blood lead < 10 microg/dL should not be considered safe. Together with other recent findings, these results add to the empirical base of support available for evaluating the adequacy of current screening guidelines and for motivating efforts at primary prevention of childhood lead exposure.

  15. Ambient Concentrations of Metabolic Disrupting Chemicals and Children’s Academic Achievement in El Paso, Texas

    PubMed Central

    Clark-Reyna, Stephanie E.; Grineski, Sara E.; Collins, Timothy W.

    2016-01-01

    Concerns about children’s weight have steadily risen alongside the manufacture and use of myriad chemicals in the US. One class of chemicals, known as metabolic disruptors, interfere with human endocrine and metabolic functioning and are of specific concern to children’s health and development. This article examines the effect of residential concentrations of metabolic disrupting chemicals on children’s school performance for the first time. Census tract-level ambient concentrations for known metabolic disruptors come from the US Environmental Protection Agency’s National Air Toxics Assessment. Other measures were drawn from a survey of primary caretakers of 4th and 5th grade children in El Paso Independent School District (El Paso, TX, USA). A mediation model is employed to examine two hypothetical pathways through which the ambient level of metabolic disruptors at a child’s home might affect grade point average. Results indicate that concentrations of metabolic disruptors are statistically significantly associated with lower grade point averages directly and indirectly through body mass index. Findings from this study have practical implications for environmental justice research and chemical policy reform in the US. PMID:27598179

  16. High Titer and Yields Achieved with Novel, Low-Severity Pretreatment Strategy

    SciTech Connect

    2016-03-01

    NREL researchers obtained high concentration sugar syrups in enzymatic hydrolysis that are fermentable to ethanol and other advanced biofuels and intermediate products at high yields. The novel DMR process is simpler and bypasses all severe pretreatment methods, thus reducing the environmental impact. The results are unprecedented. Researchers achieved a high concentration of sugars (230g/L of monomeric sugar and 270 g/L total sugar) and this low toxicity, highly fermentable syrup yielded 86 g/L ethanol (> 90 percent conversion). In addition, the lignin streams from this process can readily be converted to jet or renewable diesel blendstocks through a hydrodeoxygenation step. The NREL-developed, low severity DMR process may potentially replace higher severity chemical pretreatments and associated expensive reactors constructed of exotic alloys with a simpler process, using commercial-scale equipment commonly associated with the pulp and paper industry, to produce high concentration, low toxicity sugar streams and highly reactive lignin streams from non-food renewable biomass for biological and catalytic upgrading to advanced biofuels and chemicals. The simpler DMR process with black liquor recycling could reduce environmental and life-cycle impacts, and repurpose shuttered pulp and paper mills to help revitalize rural economies.

  17. Two Flavonolignans from Milk Thistle (Silybum marianum) Inhibit CYP2C9-Mediated Warfarin Metabolism at Clinically Achievable Concentrations

    PubMed Central

    Brantley, Scott J.; Oberlies, Nicholas H.; Kroll, David J.

    2010-01-01

    Milk thistle (Silybum marianum) is a popular herbal product used for hepatoprotection and chemoprevention. Two commercially available formulations are the crude extract, silymarin, and the semipurified product, silibinin. Silymarin consists of at least seven flavonolignans, of which the most prevalent are the diastereoisomers silybin A and silybin B; silibinin consists only of silybin A and silybin B. Based on a recent clinical study showing an interaction between a silymarin product and the CYP2C9 substrate losartan, the CYP2C9 inhibition properties of silybin A and silybin B and corresponding regioisomers, isosilybin A and isosilybin B, were evaluated using human liver microsomes (HLMs), recombinant CYP2C9 (rCYP2C9) enzymes, and the clinically relevant probe, (S)-warfarin. Silybin B was the most potent inhibitor in HLMs, followed by silybin A, isosilybin B, and isosilybin A (IC50 of 8.2, 18, 74, and >100 μM, respectively). Next, silybin A and silybin B were selected for further characterization. As with HLMs, silybin B was more potent than silybin A toward rCYP2C9*1 (6.7 versus 12 μM), rCYP2C9*2 (9.3 versus 19 μM), and rCYP2C9*3 (2.4 versus 9.3 μM). Using a matrix of five substrate (1–15 μM) and six inhibitor (1–80 μM) concentrations and HLMs, both diastereoisomers inhibited (S)-warfarin 7-hydroxylation in a manner described best by a mixed-type inhibition model (Ki values of 4.8 and 10 μM for silybin B and silybin A, respectively). These observations, combined with the high systemic silibinin concentrations (>5–75 μM) achieved in a phase I study involving prostate cancer patients, prompt clinical evaluation of a potential warfarin-milk thistle interaction. PMID:19934397

  18. Administration of ciprofloxacin and capsaicin in rats to achieve higher maximal serum concentrations.

    PubMed

    Sumano-López, Héctor; Gutiérrez-Olvera, Lilia; Aguilera-Jiménez, Rita; Gutiérrez-Olvera, Carlos; Jiménez-Gómez, Francisco

    2007-01-01

    To test if capsaicin could improve the bioavailability of ciprofloxacin (1-cyclopropyl-6-fluoro-1,4-dihydro-4-oxo-7-(1-piperazinyl)-3-quinolinecarboxylic acid, CAS 85721-33-1, Bay q 3939) in rats, 0.01, 0.1, 0.5 and 1% capsaicin ((E)-N-[(4-hydroxy-3-methoxyphenyl)methyl]-8-methyl-6-nonenamide, trans-8-methyl-N-vanillyl-6-nonenamide, CAS 404-86-4) dissolved in ethanol and mixed with 20 mg/kg of ciprofloxacin were orally administered to groups of 10 rats each. Control groups were dosed with capsaicin-free, ethanol-containing or ethanol-free ciprofloxacin. Reference intravenous pharmacokinetics of ciprofloxacin was also established. The results revealed that capsaicin increased ciprofloxacin bioavailability by approximately 70% in groups receiving preparations containing capsaicin at a rate of 0.01, 0.1 and 0.5%. Higher concentrations failed to further increase bioavailability. However, capsaicin appears to have little or no impact on the rate of absorption or clearance of ciprofloxacin. Considering that 0.01% or 0.1% capsaicin are unlikely to upset the gastrointestinal tract, it may be worth attempting to study if a similar effect occurs in man, and to evaluate if the addition of capsaicin can be used as a method to increase the area under the curve/minimum inhibitory concentration rate, a key variable to improve clinical efficacy of ciprofloxacin.

  19. The Relationship between Self-Esteem and Academic Achievement in a Group of High, Medium, and Low Secondary Public High School Achievers.

    ERIC Educational Resources Information Center

    Thomas-Brantley, Betty J.

    This study investigated the relationship between self-esteem and academic achievement in a group of 150 high, medium, and low achievers at a large midwestern public high school. Correlating data from the Coopersmith Inventory of self-esteem with grades, cumulative grade point averages, and class rank, the study disclosed a positive correlation…

  20. Relationships among Stress, Coping, and Mental Health in High-Achieving High School Students

    ERIC Educational Resources Information Center

    Suldo, Shannon M.; Shaunessy, Elizabeth; Hardesty, Robin

    2008-01-01

    This study investigates the relationships among stress, coping, and mental health in 139 students participating in an International Baccalaureate (IB) high school diploma program. Mental health was assessed using both positive indicators (life satisfaction, academic achievement, academic self-efficacy) and negative indicators (psychopathology) of…

  1. Examining Organizational Practices That Predict Persistence among High-Achieving Black Males in High School

    ERIC Educational Resources Information Center

    Anderson, Kenneth Alonzo

    2016-01-01

    Background/Context: This article summarizes an increasing trend of antideficit Black male research in mathematics and highlights opportunities to add to the research. A review of the literature shows that antideficit researchers often examine relationships between individual traits and persistence of high-achieving Black males in mathematics.…

  2. The Strengths of High-Achieving Black High School Students in a Racially Diverse Setting

    ERIC Educational Resources Information Center

    Marsh, Kris; Chaney, Cassandra; Jones, Derrick

    2012-01-01

    Robert Hill (1972) identified strengths of Black families: strong kinship bonds, strong work orientation, adaptability of family roles, high achievement orientation, and religious orientation. Some suggest these strengths sustain the physical, emotional, social, and spiritual needs of Blacks. This study used narratives and survey data from a…

  3. Relationship between High School Mathematical Achievement and Quantitative GPA

    ERIC Educational Resources Information Center

    Brown, Jennifer L.; Halpin, Glennelle; Halpin, Gerald

    2015-01-01

    The demand for STEM graduates has increased, but the number of incoming freshmen who declare a STEM major has remained stagnant. High school courses, such as calculus, can open or close the gate for students interested in careers in STEM. The purpose of this study was to determine if high school mathematics preparation was a significant…

  4. High-performance flat-panel solar thermoelectric generators with high thermal concentration.

    PubMed

    Kraemer, Daniel; Poudel, Bed; Feng, Hsien-Ping; Caylor, J Christopher; Yu, Bo; Yan, Xiao; Ma, Yi; Wang, Xiaowei; Wang, Dezhi; Muto, Andrew; McEnaney, Kenneth; Chiesa, Matteo; Ren, Zhifeng; Chen, Gang

    2011-05-01

    The conversion of sunlight into electricity has been dominated by photovoltaic and solar thermal power generation. Photovoltaic cells are deployed widely, mostly as flat panels, whereas solar thermal electricity generation relying on optical concentrators and mechanical heat engines is only seen in large-scale power plants. Here we demonstrate a promising flat-panel solar thermal to electric power conversion technology based on the Seebeck effect and high thermal concentration, thus enabling wider applications. The developed solar thermoelectric generators (STEGs) achieved a peak efficiency of 4.6% under AM1.5G (1 kW m(-2)) conditions. The efficiency is 7-8 times higher than the previously reported best value for a flat-panel STEG, and is enabled by the use of high-performance nanostructured thermoelectric materials and spectrally-selective solar absorbers in an innovative design that exploits high thermal concentration in an evacuated environment. Our work opens up a promising new approach which has the potential to achieve cost-effective conversion of solar energy into electricity.

  5. Practically Perfect in Every Way: Can Reframing Perfectionism for High-Achieving Undergraduates Impact Academic Resilience?

    ERIC Educational Resources Information Center

    Dickinson, Mary J.; Dickinson, David A. G.

    2015-01-01

    This study focuses on a pan-disciplinary scheme that targeted high-achieving undergraduate students. Earlier research from the scheme argued that high achievers have discernibly different learning and personal development support needs. One of the most frequent self-reported challenges within this high-achieving group is perfectionism. This…

  6. High Achiever: A School Modernization Uncovers Hidden Potential.

    ERIC Educational Resources Information Center

    Babcock, Regina Raiford

    2003-01-01

    Describes the renovation of Lisle Senior High School in Lisle, Illinois, including the educational context and design goals. Includes information on the architects, suppliers, and construction team. Also includes the floor plan and photographs. (EV)

  7. Gender, Student Motivation and Academic Achievement in a Midsized Wisconsin High School

    ERIC Educational Resources Information Center

    Lutzke, Steven Ronald

    2013-01-01

    This mixed-methods study investigated relationships among gender, academic motivation and achievement in a mid-sized Wisconsin high school. A questionnaire was developed that focused on perceived ability, achievement motives and achievement goals. Interviews with teachers focused on relationships among academic motivation and gender achievement.…

  8. Student Achievement Data Systems in High and Low Performing Schools

    ERIC Educational Resources Information Center

    Stachowiak, Jeannie E.

    2013-01-01

    The purpose of this study was to determine if there was a difference in how high and low performing elementary school districts use and analyze data to differentiate instruction, make changes to district/grade level curriculum, determine professional development needs, determine teacher effectiveness, and determine the use of school district…

  9. Organizational Citizenship of Faculty and Achievement of High School Students

    ERIC Educational Resources Information Center

    DiPaola, Michael F.; Hoy, Wayne K.

    2005-01-01

    All successful organizations, including successful high schools, have employees who go beyond their formal job responsibilities and freely give of their time and energy to succeed. Organ was the first to use the phrase "organizational citizenship behavior" (OCB) to denote organizationally beneficial behavior of workers that was not prescribed but…

  10. Common Core and America's High-Achieving Students

    ERIC Educational Resources Information Center

    Plucker, Jonathan A.

    2015-01-01

    While the merit and politics of the Common Core State Standards (CCSS) have been much debated and discussed, one topic has been virtually ignored: What do the standards portend for America's high-ability students? This brief addresses that question and provides guidance for CCSS-implementing districts and schools as they seek to help these…

  11. Syllabication Skills and Reading Achievement of High School Students.

    ERIC Educational Resources Information Center

    Curry, Robert L.; Geis, Lynna

    A sample of 175 students, constituting grades 10, 11, and 12 of two high schools, was used in the validation of a new Syllabication Skills Test. On the first day, the students completed four forms of the syllabication test; on the second, they completed Survey F of the Gates-MacGinitie Reading Tests. Means and standard deviations were similar for…

  12. Technology's Achilles Heel: Achieving High-Quality Implementation

    ERIC Educational Resources Information Center

    Hall, Gene E.

    2010-01-01

    An inherent characteristic of technology education is the continual development of new technologies and creating innovative applications of already existing technologies. As exciting as these innovations can be, technology educators and school staffs are frequently challenged to accomplish high levels of implementation. The metaphor of the…

  13. Alternative High School Scheduling. Student Achievement and Behavior. Research Report.

    ERIC Educational Resources Information Center

    Pisapia, John; Westfall, Amy Lynn

    In 1995 the Metropolitan Educational Research Consortium (MERC), Richmond (Virginia) commissioned a study of alternative high school scheduling modules to determine the effects of different schedules on teaching strategies, teacher and student satisfaction, and student and school performance. This report presents results of an analysis of student…

  14. High-Achieving Schools Put Equity Front and Center

    ERIC Educational Resources Information Center

    Gleason, Sonia Caus; Gerzon, Nancy

    2014-01-01

    How does professional learning look and feel in high-poverty schools where every student makes at least one year's worth of progress every year? How do schools and leaders put all the varied components of professional learning together so that they support all students learning every day? What professional learning grounds and sustains educators…

  15. More High-Achieving Students Are Choosing Community Colleges First

    ERIC Educational Resources Information Center

    Pluviose, David

    2008-01-01

    Certainly, "Tonight Show" host Jay Leno has nurtured the perception that community colleges are a punishment for underperforming high school students by joking that community colleges aren't "real colleges." This article shows that this perception belies the reality that contemporary community colleges serve students seeking trade skills but also…

  16. Impact of learning orientation on African American children's attitudes toward high-achieving peers.

    PubMed

    Marryshow, Derrick; Hurley, Eric A; Allen, Brenda A; Tyler, Kenneth M; Boykin, A Wade

    2005-01-01

    This study examined Ogbu's widely accepted thesis that African American students reject high academic achievement because they perceive its limited utility in a world where their upward mobility is constrained by racial discrimination. Boykin's psychosocial integrity model contends that Black students value high achievement but that discrepancies between their formative cultural experiences and those imposed in school lead them to reject the modes of achievement available in classrooms. Ninety Black children completed a measure of attitudes toward students who achieve via mainstream or African American cultural values. Participants rejected the mainstream achievers and embraced the African American cultural achievers. Moreover, they expected their teachers to embrace the mainstream achievers and reject those who achieved through high-verve behavior. Results suggest that Boykin's thesis is a needed refinement to Ogbu's ideas. They indicate that Black children may reject not high achievement but some of the mainstream cultural values and behaviors on which success in mainstream classrooms is made contingent.

  17. High temperature helical tubular receiver for concentrating solar power system

    NASA Astrophysics Data System (ADS)

    Hossain, Nazmul

    In the field of conventional cleaner power generation technology, concentrating solar power systems have introduced remarkable opportunity. In a solar power tower, solar energy concentrated by the heliostats at a single point produces very high temperature. Falling solid particles or heat transfer fluid passing through that high temperature region absorbs heat to generate electricity. Increasing the residence time will result in more heat gain and increase efficiency. A novel design of solar receiver for both fluid and solid particle is approached in this paper which can increase residence time resulting in higher temperature gain in one cycle compared to conventional receivers. The helical tubular solar receiver placed at the focused sunlight region meets the higher outlet temperature and efficiency. A vertical tubular receiver is modeled and analyzed for single phase flow with molten salt as heat transfer fluid and alloy625 as heat transfer material. The result is compared to a journal paper of similar numerical and experimental setup for validating our modeling. New types of helical tubular solar receivers are modeled and analyzed with heat transfer fluid turbulent flow in single phase, and granular particle and air plug flow in multiphase to observe the temperature rise in one cyclic operation. The Discrete Ordinate radiation model is used for numerical analysis with simulation software Ansys Fluent 15.0. The Eulerian granular multiphase model is used for multiphase flow. Applying the same modeling parameters and boundary conditions, the results of vertical and helical receivers are compared. With a helical receiver, higher temperature gain of heat transfer fluid is achieved in one cycle for both single phase and multiphase flow compared to the vertical receiver. Performance is also observed by varying dimension of helical receiver.

  18. Achieving High Reliability Operations Through Multi-Program Integration

    SciTech Connect

    Holly M. Ashley; Ronald K. Farris; Robert E. Richards

    2009-04-01

    Over the last 20 years the Idaho National Laboratory (INL) has adopted a number of operations and safety-related programs which has each periodically taken its turn in the limelight. As new programs have come along there has been natural competition for resources, focus and commitment. In the last few years, the INL has made real progress in integrating all these programs and are starting to realize important synergies. Contributing to this integration are both collaborative individuals and an emerging shared vision and goal of the INL fully maturing in its high reliability operations. This goal is so powerful because the concept of high reliability operations (and the resulting organizations) is a masterful amalgam and orchestrator of the best of all the participating programs (i.e. conduct of operations, behavior based safety, human performance, voluntary protection, quality assurance, and integrated safety management). This paper is a brief recounting of the lessons learned, thus far, at the INL in bringing previously competing programs into harmony under the goal (umbrella) of seeking to perform regularly as a high reliability organization. In addition to a brief diagram-illustrated historical review, the authors will share the INL’s primary successes (things already effectively stopped or started) and the gaps yet to be bridged.

  19. Telescoping Solar Array Concept for Achieving High Packaging Efficiency

    NASA Technical Reports Server (NTRS)

    Mikulas, Martin; Pappa, Richard; Warren, Jay; Rose, Geoff

    2015-01-01

    Lightweight, high-efficiency solar arrays are required for future deep space missions using high-power Solar Electric Propulsion (SEP). Structural performance metrics for state-of-the art 30-50 kW flexible blanket arrays recently demonstrated in ground tests are approximately 40 kW/cu m packaging efficiency, 150 W/kg specific power, 0.1 Hz deployed stiffness, and 0.2 g deployed strength. Much larger arrays with up to a megawatt or more of power and improved packaging and specific power are of interest to mission planners for minimizing launch and life cycle costs of Mars exploration. A new concept referred to as the Compact Telescoping Array (CTA) with 60 kW/cu m packaging efficiency at 1 MW of power is described herein. Performance metrics as a function of array size and corresponding power level are derived analytically and validated by finite element analysis. Feasible CTA packaging and deployment approaches are also described. The CTA was developed, in part, to serve as a NASA reference solar array concept against which other proposed designs of 50-1000 kW arrays for future high-power SEP missions could be compared.

  20. From Dropout to High Achiever: An Understanding of Academic Excellence through the Ethnography of High and Low Achieving Secondary School Students.

    ERIC Educational Resources Information Center

    Cuellar, Alfredo

    This paper, a follow-up to a previous review of literature on academic excellence that synthesized information from the United States and Mexico, describes an ethnographic study of high-achieving and low-achieving Hispanic secondary school students from Calexico, California and Mexicali, Baja California Mexico. Five students for each group were…

  1. Achieving high data reduction with integral cubic B-splines

    NASA Technical Reports Server (NTRS)

    Chou, Jin J.

    1993-01-01

    During geometry processing, tangent directions at the data points are frequently readily available from the computation process that generates the points. It is desirable to utilize this information to improve the accuracy of curve fitting and to improve data reduction. This paper presents a curve fitting method which utilizes both position and tangent direction data. This method produces G(exp 1) non-rational B-spline curves. From the examples, the method demonstrates very good data reduction rates while maintaining high accuracy in both position and tangent direction.

  2. High Achievement in Mathematics Education in India: A Report from Mumbai

    ERIC Educational Resources Information Center

    Raman, Manya

    2010-01-01

    This paper reports a study aimed at characterizing the conditions that lead to high achievement in mathematics in India. The study involved eight schools in the greater Mumbai region. The main result of the study is that the notion of high achievement itself is problematic, as reflected in the reports about mathematics achievement within and…

  3. Bandgap Engineering in High-Efficiency Multijunction Concentrator Cells

    SciTech Connect

    King, R. R.; Sherif, R. A.; Kinsey, G. S.; Kurtz, S.; Fetzer, C. M.; Edmondson, K. M.; Law, D. C.; Cotal, H. L.; Krut, D. D.; Ermer, J. H.; Karam, N. H.

    2005-08-01

    This paper discusses semiconductor device research paths under investigation with the aim of reaching the milestone efficiency of 40%. A cost analysis shows that achieving very high cell efficiencies is crucial for the realization of cost-effective photovoltaics, because of the strongly leveraging effect of efficiency on module packaging and balance-of systems costs. Lattice-matched (LM) GaInP/ GaInAs/ Ge 3-junction cells have achieved the highest independently confirmed efficiency at 175 suns, 25?C, of 37.3% under the standard AM1.5D, low-AOD terrestrial spectrum. Lattice-mismatched, or metamorphic (MM), materials offer still higher potential efficiencies, if the crystal quality can be maintained. Theoretical efficiencies well over 50% are possible for a MM GaInP/ 1.17-eV GaInAs/ Ge 3-junction cell limited by radiative recombination at 500 suns. The bandgap - open circuit voltage offset, (Eg/q) - Voc, is used as a valuable theoretical and experimental tool to characterize multijunction cells with subcell bandgaps ranging from 0.7 to 2.1 eV. Experimental results are presented for prototype 6-junction cells employing an active {approx}1.1-eV dilute nitride GaInNAs subcell, with active-area efficiency greater than 23% and over 5.3 V open-circuit voltage under the 1-sun AM0 space spectrum. Such cell designs have theoretical efficiencies under the terrestrial spectrum at 500 suns concentration exceeding 55% efficiency, even for lattice-matched designs.

  4. Design requirements for high-efficiency high concentration ratio space solar cells

    NASA Technical Reports Server (NTRS)

    Rauschenbach, H.; Patterson, R.

    1980-01-01

    A miniaturized Cassegrainian concentrator system concept was developed for low cost, multikilowatt space solar arrays. The system imposes some requirements on solar cells which are new and different from those imposed for conventional applications. The solar cells require a circular active area of approximately 4 mm in diameter. High reliability contacts are required on both front and back surfaces. The back area must be metallurgically bonded to a heat sink. The cell should be designed to achieve the highest practical efficiency at 100 AMO suns and at 80 C. The cell design must minimize losses due to nonuniform illumination intensity and nonnormal light incidence. The primary radiation concern is the omnidirectional proton environment.

  5. Rectangular Dielectric-loaded Structures for Achieving High Acceleration Gradients

    NASA Astrophysics Data System (ADS)

    Wang, Changbiao; Yakovlev, V. P.; Marshall, T. C.; LaPointe, M. A.; Hirshfield, J. L.

    2006-11-01

    Rectangular dielectric-loaded structures are described that may sustain higher acceleration gradients than conventional all-metal structures with similar apertures. One structure is a test cavity designed to ascertain the breakdown limits of dielectrics, while a second structure could be the basis for a two-beam accelerator. CVD diamond is an attractive dielectric for a high-gradient structure, since the published DC breakdown limit for CVD diamond is ˜ 2 GV/m, although the limit has never been determined for RF fields. Here we present a design of a diamond-lined test cavity to measure the breakdown limit. The designed cavity operates at 34 GHz, where with 10-MW input power it is expected to produce an ˜800 MV/m field on the diamond surface—provided breakdown is avoided. The two channel rectangular dielectric-loaded waveguide could be a two-beam accelerator structure, in which a drive beam is in one channel and an accelerated beam is in the other. The RF power produced by drive bunches in the drive channel is continuously coupled to the acceleration channel. The ratio of fields in the channels (transformer ratio) for the operating mode can be designed by adjusting the dimensions of the structure. An example of the two-channel structure is described, in which a train of five 3-nC drive bunches excites wake fields in the accelerator channel of up to 1.3 GV/m with a transformer ratio of 10 for the design mode.

  6. Effectiveness of increasing the frequency of posaconazole syrup administration to achieve optimal plasma concentrations in patients with haematological malignancy.

    PubMed

    Park, Wan Beom; Cho, Joo-Youn; Park, Sang-In; Kim, Eun Jung; Yoon, Seonghae; Yoon, Seo Hyun; Lee, Jeong-Ok; Koh, Youngil; Song, Kyoung-Ho; Choe, Pyoeng Gyun; Yu, Kyung-Sang; Kim, Eu Suk; Bang, Su Mi; Kim, Nam Joong; Kim, Inho; Oh, Myoung-Don; Kim, Hong Bin; Song, Sang Hoon

    2016-07-01

    Few data are available on whether adjusting the dose of posaconazole syrup is effective in patients receiving anti-cancer chemotherapy. The aim of this prospective study was to analyse the impact of increasing the frequency of posaconazole administration on optimal plasma concentrations in adult patients with haematological malignancy. A total of 133 adult patients receiving chemotherapy for acute myeloid leukaemia or myelodysplastic syndrome who received posaconazole syrup 200 mg three times daily for fungal prophylaxis were enrolled in this study. Drug trough levels were measured by liquid chromatography-tandem mass spectrometry. In 20.2% of patients (23/114) the steady-state concentration of posaconazole was suboptimal (<500 ng/mL) on Day 8. In these patients, the frequency of posaconazole administration was increased to 200 mg four times daily. On Day 15, the median posaconazole concentration was significantly increased from 368 ng/mL [interquartile range (IQR), 247-403 ng/mL] to 548 ng/mL (IQR, 424-887 ng/mL) (P = 0.0003). The median increase in posaconazole concentration was 251 ng/mL (IQR, 93-517 ng/mL). Among the patients with initially suboptimal levels, 79% achieved the optimal level unless the steady-state level was <200 ng/mL. This study shows that increasing the administration frequency of posaconazole syrup is effective for achieving optimal levels in patients with haematological malignancy undergoing chemotherapy.

  7. Hair and toenail arsenic concentrations of residents living in areas with high environmental arsenic concentrations.

    PubMed Central

    Hinwood, Andrea L; Sim, Malcolm R; Jolley, Damien; de Klerk, Nick; Bastone, Elisa B; Gerostamoulos, Jim; Drummer, Olaf H

    2003-01-01

    Surface soil and groundwater in Australia have been found to contain high concentrations of arsenic. The relative importance of long-term human exposure to these sources has not been established. Several studies have investigated long-term exposure to environmental arsenic concentrations using hair and toenails as the measure of exposure. Few have compared the difference in these measures of environmental sources of exposure. In this study we aimed to investigate risk factors for elevated hair and toenail arsenic concentrations in populations exposed to a range of environmental arsenic concentrations in both drinking water and soil as well as in a control population with low arsenic concentrations in both drinking water and soil. In this study, we recruited 153 participants from areas with elevated arsenic concentrations in drinking water and residential soil, as well as a control population with no anticipated arsenic exposures. The median drinking water arsenic concentrations in the exposed population were 43.8 micro g/L (range, 16.0-73 micro g/L) and median soil arsenic concentrations were 92.0 mg/kg (range, 9.1-9,900 mg/kg). In the control group, the median drinking water arsenic concentration was below the limit of detection, and the median soil arsenic concentration was 3.3 mg/kg. Participants were categorized based on household drinking water and residential soil arsenic concentrations. The geometric mean hair arsenic concentrations were 5.52 mg/kg for the drinking water exposure group and 3.31 mg/kg for the soil exposure group. The geometric mean toenail arsenic concentrations were 21.7 mg/kg for the drinking water exposure group and 32.1 mg/kg for the high-soil exposure group. Toenail arsenic concentrations were more strongly correlated with both drinking water and soil arsenic concentrations; however, there is a strong likelihood of significant external contamination. Measures of residential exposure were better predictors of hair and toenail arsenic

  8. High Performance Concentrating Photovoltaic Module Designs Employing Reflective Lens Optics

    NASA Astrophysics Data System (ADS)

    Vasylyev, Sergey V.; Vasylyev, Viktor P.

    2011-12-01

    The present study is aimed at advancing the optical component as well as optimizing the design of concentrating photovoltaic (CPV) modules in order to increase the conversion efficiency and improve the utility of CPV while obtaining the prescribed concentration ratio. In this work, we turn to non-traditional concentrating optics, namely Reflective Lenses™ (RL), first introduced in early 2000s. The optical configuration of RLs is unique since it combines the very low F/D number (hence resulting in a very low profile of the unit) of mirrors with a rear-focus of lenses and uses only a single-stage reflection. A liner-focus version of RLs, the Slat-Array Concentrator (SAC), is a capable alternative to the parabolic troughs for mid-concentration CPV. A point-focus version called the Ring-Array Concentrator (RAC) is deemed suitable for high concentration photovoltaics.

  9. Evaluation of high-concentration photovoltaic power plants

    SciTech Connect

    Stolte, W.J. ); Whisnant, R.A. ); McGowin, C.R. )

    1991-01-01

    This paper describes the conceptual design, and estimated cost and performance of two high-concentration, 50 MW photovoltaic power plants. Both designs are based on a similar advanced back-contact silicon concentrator cell. The first design uses Fresnel lens/glass silo modules mounted on two-axis tracking arrays. The second design has all of the cells mounted on a central receiver on top of a single tower, with heliostats concentrating sunlight onto the receiver.

  10. Multijunction Photovoltaic Technologies for High-Performance Concentrators: Preprint

    SciTech Connect

    McConnell, R.; Symko-Davies, M.

    2006-05-01

    Multijunction solar cells provide high-performance technology pathways leading to potentially low-cost electricity generated from concentrated sunlight. The National Center for Photovoltaics at the National Renewable Energy Laboratory has funded different III-V multijunction solar cell technologies and various solar concentration approaches. Within this group of projects, III-V solar cell efficiencies of 41% are close at hand and will likely be reported in these conference proceedings. Companies with well-developed solar concentrator structures foresee installed system costs of $3/watt--half of today's costs--within the next 2 to 5 years as these high-efficiency photovoltaic technologies are incorporated into their concentrator photovoltaic systems. These technology improvements are timely as new large-scale multi-megawatt markets, appropriate for high performance PV concentrators, open around the world.

  11. Highly accurate boronimeter assay of concentrated boric acid solutions

    SciTech Connect

    Ball, R.M. )

    1992-01-01

    The Random-Walk Boronimeter has successfully been used as an on-line indicator of boric acid concentration in an operating commercial pressurized water reactor. The principle has been adapted for measurement of discrete samples to high accuracy and to concentrations up to 6000 ppm natural boron in light water. Boric acid concentration in an aqueous solution is a necessary measurement in many nuclear power plants, particularly those that use boric acid dissolved in the reactor coolant as a reactivity control system. Other nuclear plants use a high-concentration boric acid solution as a backup shutdown system. Such a shutdown system depends on rapid injection of the solution and frequent surveillance of the fluid to ensure the presence of the neutron absorber. The two methods typically used to measure boric acid are the chemical and the physical methods. The chemical method uses titration to determine the ionic concentration of the BO[sub 3] ions and infers the boron concentration. The physical method uses the attenuation of neutrons by the solution and infers the boron concentration from the neutron absorption properties. This paper describes the Random-Walk Boronimeter configured to measure discrete samples to high accuracy and high concentration.

  12. Formal Operational Precocity and Achievement in Biology among Some Nigerian High School Students.

    ERIC Educational Resources Information Center

    Ehindero, Olusola Joseph

    1979-01-01

    Compares the performances on a battery of six Piagetian tasks of 80 Nigerian high school students classified as high and low achievers in biology. The relationship between performance of very bright biology students (high achievers) and intellectual precocity is also investigated. (HM)

  13. The Chinese High School Student's Stress in the School and Academic Achievement

    ERIC Educational Resources Information Center

    Liu, Yangyang; Lu, Zuhong

    2011-01-01

    In a sample of 466 Chinese high school students, we examined the relationships between Chinese high school students' stress in the school and their academic achievements. Regression mixture modelling identified two different classes of the effects of Chinese high school students' stress on their academic achievements. One class contained 87% of…

  14. Beyond Academic Reputation: Factors that Influence the College of First Choice for High Achieving Students

    ERIC Educational Resources Information Center

    Schoenherr, Holly J.

    2009-01-01

    Studies that have investigated college choice factors for high-achieving students repeatedly cite academic reputation as one of the top indicators of choice but have not indicated why some high-achieving students choose to attend universities with a less prestigious reputation than the more highly prestigious options available to them. The purpose…

  15. Does High School Facility Quality Affect Student Achievement? A Two-Level Hierarchical Linear Model

    ERIC Educational Resources Information Center

    Bowers, Alex J.; Urick, Angela

    2011-01-01

    The purpose of this study is to isolate the independent effects of high school facility quality on student achievement using a large, nationally representative U.S. database of student achievement and school facility quality. Prior research on linking school facility quality to student achievement has been mixed. Studies that relate overall…

  16. The Effects of Web-Based/Non-Web-Based Problem-Solving Instruction and High/Low Achievement on Students' Problem-Solving Ability and Biology Achievement

    ERIC Educational Resources Information Center

    Yu, Wen-Feng; She, Hsiao-Ching; Lee, Yu-Mei

    2010-01-01

    This study investigates the effects of two factors: the mode of problem-solving instruction (i.e. Web-based versus non-Web-based) and the level of academic achievement (i.e. high achievers versus low achievers) on students' problem-solving ability and biology achievement. A quasi-experimental design was used, in which the experimental group…

  17. 9-Fold Fresnel Köhler concentrator for increased uniform irradiance on high concentrations

    NASA Astrophysics Data System (ADS)

    Mendes-Lopes, João; Benítez, Pablo; Zamora, Pablo; Miñano, Carlos

    2013-09-01

    Non-uniform irradiance patterns created by Concentrated Photovoltaics (CPV) concentrators over Multi-Junction Cells (MJC) can originate significant power losses, especially when there are different spectral irradiance distributions over the different MJC junctions. This fact has an increased importance considering the recent advances in 4 and 5 junction cells. The spectral irradiance distributions are especially affected with thermal effects on Silicone-on-Glass (SoG) CPV systems. This work presents a new CPV optical design, the 9-fold Fresnel Köhler concentrator, prepared to overcome these effects at high concentrations while maintaining a large acceptance angle, paving the way for a future generation of high efficiency CPV systems of 4 and 5 junction cells.

  18. Achieving high mass-throughput of therapeutic proteins through parvovirus retentive filters.

    PubMed

    Bolton, Glen R; Basha, Jonida; Lacasse, Daniel P

    2010-01-01

    Parvovirus retentive filters that assure removal of viruses and virus-like particles during the production of therapeutic proteins significantly contribute to total manufacturing costs. Operational approaches that can increase throughput and reduce filtration area would result in a significant cost savings. A combination of methods was used to achieve high throughputs of an antibody or therapeutic protein solution through three parvovirus retentive filters. These methods included evaluation of diatomaceous earth or size-based prefilters, the addition of additives, and the optimization of protein concentration, temperature, buffer composition, and solution pH. An optimum temperature of 35°C was found for maximizing throughput through the Virosart CPV and Viresolve Pro filters. Mass-throughput values of 7.3, 26.4, and 76.2 kg/m(2) were achieved through the Asahi Planova 20N, Virosart CPV, and Viresolve Pro filters, respectively, in 4 h of processing. Mass-throughput values of 73, 137, and 192 kg/m(2) were achieved through a Millipore Viresolve Pro filter in 4.0, 8.8, and 22.1 h of processing, respectively, during a single experiment. However, large-scale parvovirus filtration operations are typically controlled to limit volumetric throughput to below the level achieved during small-scale virus spiking experiments. The virus spike may cause significant filter plugging, limiting throughput. Therefore newer parvovirus filter spiking strategies should be adopted that may lead to more representative viral clearance data and higher utilization of large-scale filter capacity.

  19. Nitrification of ammonia nitrogen high concentration in membrane assisted bioreactor.

    PubMed

    Zabczyński, S; Surmacz-Górska, J; Miksch, K

    2003-01-01

    Use of the membrane-assisted bioreactors (MBR) in wastewater treatment can bring a lot of advantages. Usually COD removal achieves level 90% and nitrification of ammonia nitrogen concentrations typical for municipal wastewater performs without any disturbances, what was confirmed by large number of experiments. However, inhibition of nitrification of the high ammonia nitrogen concentration was noticed. In this study, the performance of ammonia-rich wastewater nitrification in membrane-assisted bioreactor (MBR) was examined. With SRT of 40, 32, 24 and 16 days any nitrification inhibition effect wasn't noticed. Ammonia nitrogen removal was around 98% and full nitrification was observed. At the sludge age equal to 12 d the first stage of nitrification was full, but the second stage of nitrification was incomplete. The variation in number and presence of the higher organisms were noticed at the all examined sludge ages. With SRT of 40, 32, 24 and 16 days the free ciliates were prominent organisms. At the sludge age of 12 days the domination of flagellates was observed The kinetic constants of the high-ammonia wastewater nitrification were calculated The average value of Vmax at the sludge age 12, 16 and 24 days was constant (4.7 mg NH4(+)-N/g MLSS h, 4.8 mg NH4(+)-N/g MLSS h and 4.8 mg NH4(+)-N/g MLSS, respectively), but the value of Km rose, when the sludge age increased (6.8 mg NH4(+)-N/L for 12 days, 11.3 mg NH4(+)-N/L for 16 days, 21.6 mg NH4(+)-N/L for 24 days). At the sludge age 32 and 40 days the increase of Vmax was observed (7.2 mg NH4(+)-N/g MLSS h and 12.5 mg NH4(+)-N/g MLSS h, respectively) and, also, changes of Km (6.8 mg NH4(+)-N/L and 44 mg NH4(+)-N/L, respectively. Concerning the second stage of nitrification value of Vmax decreased with the increase of the sludge age and the average Km varied from 20.3 to 31.3 mg NO2(-)-N/L.

  20. Factors impeding enzymatic wheat gluten hydrolysis at high solid concentrations.

    PubMed

    Hardt, N A; Janssen, A E M; Boom, R M; van der Goot, A J

    2014-07-01

    Enzymatic wheat gluten hydrolysis at high solid concentrations is advantageous from an environmental and economic point of view. However, increased wheat gluten concentrations result in a concentration effect with a decreased hydrolysis rate at constant enzyme-to-substrate ratios and a decreased maximum attainable degree of hydrolysis (DH%). We here identified the underlying factors causing the concentration effect. Wheat gluten was hydrolyzed at solid concentrations from 4.4% to 70%. The decreased hydrolysis rate was present at all solid concentrations and at any time of the reaction. Mass transfer limitations, enzyme inhibition and water activity were shown to not cause this hydrolysis rate limitation up to 50% solids. However, the hydrolysis rate limitation can be, at least partly, explained by a second-order enzyme inactivation process. Furthermore, mass transfer impeded the hydrolysis above 60% solids. Addition of enzyme after 24 h at high solid concentrations scarcely increased the DH%, suggesting that the maximum attainable DH% decreases at high solid concentrations. Reduced enzyme activities caused by low water activities can explain this DH% limitation. Finally, a possible influence of the plastein reaction on the DH% limitation is discussed.

  1. Achieving High Strength and High Ductility in Friction Stir-Processed Cast Magnesium Alloy

    NASA Astrophysics Data System (ADS)

    Yuan, Wei; Panigrahi, Sushanta K.; Mishra, Rajiv S.

    2013-08-01

    Friction stir processing (FSP) is emerging as an effective tool for microstructural modification and property enhancement. As-cast AZ91 magnesium alloy was friction stir processed with one-pass and two-pass to examine the influence of processing conditions on microstructural evolution and corresponding mechanical properties. Grain refinement accompanied with development of strong basal texture was observed for both processing conditions. Ultrafine-grained (UFG) AZ91 was achieved under two-pass FSP with fine precipitates distributed on the grain boundary. The processed UFG AZ91 exhibited a high tensile strength of ~435 MPa (117 pct improvement) and tensile fracture elongation of ~23 pct. The promising combination of strength and ductility is attributed to the elimination of casting porosity, and high density of fine precipitates in an UFG structure with quite low dislocation density. The effects of grain size, precipitate, and texture on deformation behavior have been discussed.

  2. An Analysis of Java Programming Behaviors, Affect, Perceptions, and Syntax Errors among Low-Achieving, Average, and High-Achieving Novice Programmers

    ERIC Educational Resources Information Center

    Rodrigo, Ma. Mercedes T.; Andallaza, Thor Collin S.; Castro, Francisco Enrique Vicente G.; Armenta, Marc Lester V.; Dy, Thomas T.; Jadud, Matthew C.

    2013-01-01

    In this article we quantitatively and qualitatively analyze a sample of novice programmer compilation log data, exploring whether (or how) low-achieving, average, and high-achieving students vary in their grasp of these introductory concepts. High-achieving students self-reported having the easiest time learning the introductory programming…

  3. High Black Carbon (BC) Concentrations along Indian National Highways

    NASA Astrophysics Data System (ADS)

    Kumar, S.; Singh, A. K.; Singh, R. P.

    2015-12-01

    Abstract:Black carbon (BC), the optically absorbing component of carbonaceous aerosol, has direct influence on radiation budget and global warming. Vehicular pollution is one of the main sources for poor air quality and also atmospheric pollution. The number of diesel vehicles has increased on the Indian National Highways during day and night; these vehicles are used for the transport of goods from one city to another city and also used for public transport. A smoke plume from the vehicles is a common feature on the highways. We have made measurements of BC mass concentrations along the Indian National Highways using a potable Aethalometer installed in a moving car. We have carried out measurements along Varanasi to Kanpur (NH-2), Varanasi to Durgapur (NH-2), Varanasi to Singrauli (SH-5A) and Varanasi to Ghazipur (NH-29). We have found high concentration of BC along highways, the average BC mass concentrations vary in the range 20 - 40 µg/m3 and found high BC mass concentrations up to 600 μg/m3. Along the highways high BC concentrations were characteristics of the presence of industrial area, power plants, brick kilns and slow or standing vehicles. The effect of increasing BC concentrations along the National Highways and its impact on the vegetation and human health will be presented. Key Words: Black Carbon; Aethalometer; mass concentration; Indian National Highways.

  4. High-speed VLSI concentrators for terabit intelligent optical backplanes

    NASA Astrophysics Data System (ADS)

    Supmonchai, Boonchuay; Szymanski, Ted H.

    1998-05-01

    Self-routing `concentrators' are fundamental building blocks of optical switching systems. An N-to-M concentrator can process and extract data packets from N optical channels and forward the packets to M electrical channels, where typically N M. Terabit Optical Backplanes which exploit free-space optical data links, with bandwidths approaching 1 - 10 Terabits per second will require extremely fast self- routing concentrators which can make routing decisions within a few nanoseconds. In this paper, a VLSI analysis of a new circuit called the `Daisy Chain' concentrator is presented. This concentrator has a regular topology suitable for very efficient VLSI layout, which leads to very high clock rates. The analyses are performed using 0.8 micrometers standard cell CMOS technology with the Synopsys CAD tool. The results shows that the proposed concentrator uses substantially less VLSI area from 20 - 50% less in the control logic and up to 150% less on the switching logic than the previous best known concentrator circuit. It also performs significantly faster, ranging from 20 - 40% faster in the control logic and 150 - 300% faster in the switching logic. Using 0.8 micrometers CMOS technology, the proposed concentrator can be used in smart pixel arrays for optical backplanes with clock rates in the range of 500 Mhz. Using faster CMOS or ECL logic, the concentrator can support clock rates in the several Gigahertz range.

  5. The Effect of the Time Management Art on Academic Achievement among High School Students in Jordan

    ERIC Educational Resources Information Center

    Al-Zoubi, Maysoon

    2016-01-01

    This study aimed at recognizing the effect of the Time Management Art on academic achievement among high school students in the Hashemite Kingdom of Jordan. The researcher employed the descriptive-analytic research to achieve the purpose of the study where he chose a sample of (2000) high school female and male students as respondents to the…

  6. Effects of a Collaborative Science Intervention on High Achieving Students' Learning Anxiety and Attitudes toward Science

    ERIC Educational Resources Information Center

    Hong, Zuway-R.

    2010-01-01

    This study investigated the effects of a collaborative science intervention on high achieving students' learning anxiety and attitudes toward science. Thirty-seven eighth-grade high achieving students (16 boys and 21 girls) were selected as an experimental group who joined a 20-week collaborative science intervention, which integrated and utilized…

  7. Individual and Longitudinal Differences among High and Low-Achieving, LD, and ADHD L2 Learners

    ERIC Educational Resources Information Center

    Sparks, Richard L.; Humbach, Nancy; Javorsky, James

    2008-01-01

    High-achieving (HA) and low-achieving (LA), learning disabled (LD), and attention deficit hyperactivity disorder (ADHD) high school students were followed over two years of L2 study and compared on measures of L1 literacy (reading and writing) in elementary school, L1 cognitive ability, L2 aptitude, oral and written L2 proficiency, and L2 word…

  8. International Note: Between-Domain Relations of Chinese High School Students' Academic Achievements

    ERIC Educational Resources Information Center

    Yangyang, Liu

    2012-01-01

    The present study examined the between-domain relations of Chinese high school students' academic achievements. In a sample of 1870 Chinese 10th grade students, the results indicated that Chinese high school students' academic achievements were correlated across nine subjects. In line with the previous Western findings, the findings suggested that…

  9. A Longitudinal Investigation of Project-Based Instruction and Student Achievement in High School Social Studies

    ERIC Educational Resources Information Center

    Summers, Emily J.; Dickinson, Gail

    2012-01-01

    This longitudinal study focused on how project-based instruction (PBI) influenced secondary social studies students' academic achievement and promoted College and Career Readiness (CCR). We explored and compared student achievement in a PBI high school versus a traditional instruction high school within the same rural school district. While…

  10. Parent-Child Relations and Psychological Adjustment among High-Achieving Chinese and European American Adolescents

    ERIC Educational Resources Information Center

    Qin, Desiree Baolian; Rak, Eniko; Rana, Meenal; Donnellan, M. Brent

    2012-01-01

    Chinese American students are often perceived as problem-free high achievers. Recent research, however, suggests that high-achieving Chinese American students can experience elevated levels of stress, especially comparing to their peers from other ethnic groups. In this paper, we examine how family dynamics may influence psychological adjustment…

  11. High-Achieving and Average Students' Reading Growth: Contrasting School and Summer Trajectories

    ERIC Educational Resources Information Center

    Rambo-Hernandez, Karen E.; McCoach, D. Betsy

    2015-01-01

    Much is unknown about how initially high-achieving students grow academically, especially given the measurement issues inherent in assessing growth for the highest performing students. This study compared initially high-achieving and average students' growth in reading (in a cohort of third-grade students from 2,000 schools) over 3 years.…

  12. High concentration low wattage solar arrays and their applications

    NASA Astrophysics Data System (ADS)

    Hoffmann, Robert; O'Gallagher, Joseph; Winston, Roland

    1997-02-01

    Midway Labs currently produces a 335x concentrator module that has reached as high as 19% active area efficiency in production. The current production module uses the single crystal silicon back contact SunPower cell. The National Renewable Energy Lab has developed a multi junction cell using GalnP/GaAs technologies. The high efficiency (>30%) and high cell voltage offer an opportunity for Midway Labs to develop a tracking concentrator module that will provide 24 volts in the 140 to 160 watt range. This voltage and wattage range is applicable to a range of small scale water pumping applications that make up the bulk of water pumping solar panel sales.

  13. The Meaning High-Achieving African-American Males in an Urban High School Ascribe to Mathematics

    ERIC Educational Resources Information Center

    Thompson, LaTasha; Davis, Julius

    2013-01-01

    Many researchers, educators, administrators, policymakers and members of the general public doubt the prevalence of high-achieving African-American males in urban high schools capable of excelling in mathematics. As part of a larger study, the current study explored the educational experiences of four high-achieving African-American males…

  14. High concentration honey chitosan electrospun nanofibers: biocompatibility and antibacterial effects.

    PubMed

    Sarhan, Wessam A; Azzazy, Hassan M E

    2015-05-20

    Honey nanofibers represent an attractive formulation with unique medicinal and wound healing advantages. Nanofibers with honey concentrations of <10% were prepared, however, there is a need to prepare nanofibers with higher honey concentrations to increase the antibacterial and wound healing effects. In this work, chitosan and honey (H) were cospun with polyvinyl alcohol (P) allowing the fabrication of nanofibers with high honey concentrations up to 40% and high chitosan concentrations up to 5.5% of the total weight of the fibers using biocompatible solvents (1% acetic acid). The fabricated nanofibers were further chemically crosslinked, by exposure to glutaraldehyde vapor, and physically crosslinked by heating and freezing/thawing. The new HP-chitosan nanofibers showed pronounced antibacterial activity against Staphylococcus aureus but weak antibacterial activity against Escherichia coli. The developed HP-chitosan nanofibers revealed no cytotoxicity effects on cultured fibroblasts. In conclusion, biocompatible, antimicrobial crosslinked honey/polyvinyl alcohol/chitosan nanofibers were developed which hold potential as effective wound dressing.

  15. Concentrating and spectrum splitting optical device in high efficiency CPV module with five bandgaps

    NASA Astrophysics Data System (ADS)

    Taudien, Jerker Y.; Kern, Ludwig A.

    2013-09-01

    There is a need for a high efficiency low cost solar energy conversion system. Currently, most concentrating photovoltaic (CPV) systems concentrate the solar spectrum onto triple junction cells to strive for high conversion efficiencies and low cost. Other approaches to high efficiency use spectrum splitting. Triple junction systems are limited in efficiency and spectrum splitting systems are usually too costly for mass production. The objective is to design a spectrum splitting solar concentrator, using reverse ray tracing methods, to overcome the efficiency and cost limitations of current systems by using a single low cost optical device to concentrate and split the solar spectrum onto a large number of target photovoltaic (PV) cells. Dispersive properties of standard optical materials, such as glass or plastic, are utilized to achieve the desired spectral separation. Reverse ray tracing is used to simultaneously optimize the shape of the top and bottom interfaces of the solar concentrator to achieve the desired split spectrum at the target PV cells. Additional strategies to increase system efficiency and minimize optical losses, including draft surface shading and corner rounding losses, are explored. A CPV module, including the spectrum splitting solar concentrator and five PV cells of different bandgaps, is proposed. This spectrum splitting CPV system has a calculated aggregate cell conversion efficiency that exceeds 45%, has the potential to be mass produced, and meets the need for a high efficiency low cost solar energy conversion system.

  16. Freeform solar concentrator with a highly asymmetric acceptance cone

    NASA Astrophysics Data System (ADS)

    Wheelwright, Brian; Angel, J. Roger P.; Coughenour, Blake; Hammer, Kimberly

    2014-10-01

    A solar concentrator with a highly asymmetric acceptance cone is investigated. Concentrating photovoltaic systems require dual-axis sun tracking to maintain nominal concentration throughout the day. In addition to collecting direct rays from the solar disk, which subtends ~0.53 degrees, concentrating optics must allow for in-field tracking errors due to mechanical misalignment of the module, wind loading, and control loop biases. The angular range over which the concentrator maintains <90% of on-axis throughput is defined as the optical acceptance angle. Concentrators with substantial rotational symmetry likewise exhibit rotationally symmetric acceptance angles. In the field, this is sometimes a poor match with azimuth-elevation trackers, which have inherently asymmetric tracking performance. Pedestal-mounted trackers with low torsional stiffness about the vertical axis have better elevation tracking than azimuthal tracking. Conversely, trackers which rotate on large-footprint circular tracks are often limited by elevation tracking performance. We show that a line-focus concentrator, composed of a parabolic trough primary reflector and freeform refractive secondary, can be tailored to have a highly asymmetric acceptance angle. The design is suitable for a tracker with excellent tracking accuracy in the elevation direction, and poor accuracy in the azimuthal direction. In the 1000X design given, when trough optical errors (2mrad rms slope deviation) are accounted for, the azimuthal acceptance angle is +/- 1.65°, while the elevation acceptance angle is only +/-0.29°. This acceptance angle does not include the angular width of the sun, which consumes nearly all of the elevation tolerance at this concentration level. By decreasing the average concentration, the elevation acceptance angle can be increased. This is well-suited for a pedestal alt-azimuth tracker with a low cost slew bearing (without anti-backlash features).

  17. Sterile Filtration of Highly Concentrated Protein Formulations: Impact of Protein Concentration, Formulation Composition, and Filter Material.

    PubMed

    Allmendinger, Andrea; Mueller, Robert; Huwyler, Joerg; Mahler, Hanns-Christian; Fischer, Stefan

    2015-10-01

    Differences in filtration behavior of concentrated protein formulations were observed during aseptic drug product manufacturing of biologics dependent on formulation composition. The present study investigates filtration forces of monoclonal antibody formulations in a small-scale set-up using polyvinylidene difluoride (PVDF) or polyethersulfone (PES) filters. Different factors like formulation composition and protein concentration related to differences in viscosity, as well as different filtration rates were evaluated. The present study showed that filtration behavior was influenced by the presence or absence of a surfactant in the formulation, which defines the interaction between filter membrane and surface active formulation components. This can lead to a change in filter resistance (PES filter) independent on the buffer system used. Filtration behavior was additionally defined by rheological non-Newtonian flow behavior. The data showed that high shear rates resulting from small pore sizes and filtration pressure up to 1.0 bar led to shear-thinning behavior for highly concentrated protein formulations. Differences in non-Newtonian behavior were attributed to ionic strength related to differences in repulsive and attractive interactions. The present study showed that the interplay of formulation composition, filter material, and filtration rate can explain differences in filtration behavior/filtration flux observed for highly concentrated protein formulations thus guiding filter selection.

  18. Calculation of injection forces for highly concentrated protein solutions.

    PubMed

    Fischer, Ingo; Schmidt, Astrid; Bryant, Andrew; Besheer, Ahmed

    2015-09-30

    Protein solutions often manifest a high viscosity at high solution concentrations, thus impairing injectability. Accordingly, accurate prediction of the injection force based on solution viscosity can greatly support protein formulation and device development. In this study, the shear-dependent viscosity of three concentrated protein solutions is reported, and calculated injection forces obtained by two different mathematical models are compared against measured values. The results show that accurate determination of the needle dimensions and the shear-thinning behavior of the protein solutions is vital for injection force prediction. Additionally, one model delivered more accurate results, particularly for solutions with prominent shear-thinning behavior.

  19. The impact of collective teacher efficacy on student achievement in high school science

    NASA Astrophysics Data System (ADS)

    Burcham, Mark W.

    This dissertation was designed to examine the impact of collective teacher efficacy on high school science achievement by looking at relationships among collective teacher efficacy, its two constructs, group competence and group task analysis, and high school science achievement scores at four rural high schools in Northwestern North Carolina. The researcher gathered historical test data from the testing coordinator from the school system and then administered the Collective Teacher Efficacy Instrument, developed by Goddard, Hoy, and Woolfolk Hoy (2000), to 24 science teachers from the four high schools. Using this information, the researcher conducted statistical analyses to determine the relationships among collective teacher efficacy, group competence, and group task analysis as compared with the tested science curriculum (physical science, biology, chemistry, and physics). The researcher also examined which construct was the most contributing factor and examined differences in efficacy levels and student achievement levels at each high school. Analysis of the data from this study indicated collective teacher efficacy, as well as its two constructs, group competence and group task analysis, does have a positive impact on student achievement in high school science. Analysis of the data revealed group competence is the major contributing factor for student achievement in biology and group task analysis is the major contributing factor for student achievement in physical science, chemistry, and physics. Further analysis of the data in this study, also revealed that the two high schools with the highest levels of collective teacher efficacy had the highest levels of student achievement.

  20. High estrogen concentrations in receiving river discharge from a concentrated livestock feedlot.

    PubMed

    Chen, Te-San; Chen, Ting-Chien; Yeh, Kuei-Jyum C; Chao, How-Ran; Liaw, Ean-Tun; Hsieh, Chi-Ying; Chen, Kuan-Chung; Hsieh, Lien-Te; Yeh, Yi-Lung

    2010-07-15

    Environmental estrogenic chemicals interrupt endocrine systems and generate reproductive abnormalities in wildlife, especially natural and synthetic estrogenic steroid hormones such as 17beta-estradiol (E2), estrone (E1), estriol (E3), 17alpha-ethynylestradiol (EE2), and diethylstilbestrol (DES). Concentrated animal feedlot operations (CAFOs) are of particular concern since large amounts of naturally excreted estrogens are discharged into aquatic environments. This study investigated E2, E1, E3, EE2, and DES with high performance liquid chromatography/tandem mass (HPLC-MS/MS) analyses along Wulo Creek in southern Taiwan, near a concentrated livestock feedlot containing 1,030,000 broiler chickens, 934,000 laying hens, 85,000 pigs, and 1500 cattle. Sampling was performed from December 2008 to May 2009, in which 54 samples were collected. Experimental results indicate that concentrations of EE2 were lower than the limit of detection (LOD), and concentrations of DES were only detected twice. Concentrations ranged from 7.4 to 1267 ng/L for E1, from not detected (ND) to 313.6 ng/L for E2, and from ND to 210 ng/L for E3. E1 had the highest average mass fraction (72.2 + or - 3.6%), which was significantly higher than E3 (16.2 + or - 1.7%) and E2 (11.5 + or - 2.6%). Additionally, the mean E2 equivalent quotient (EEQ) ranged from 17.3 to 137.9 ng-E2/L. Despite having a markedly lower concentration than E1, E2 more significantly contributed (52.4 + or - 6.0%) EEQ than E1 (19.7 + or - 3.5%). Moreover, the concentrations of E2, E1, and E3 upstream were significantly higher than concentrations downstream, suggesting a high attenuation effect and fast degradation in the study water. Most concentrations in winter season were higher than those of spring season due to the low dilution effect and low microbial activity in the winter season. Based on the results of this study, we recommend further treatment of the wastewater discharge from the feedlot.

  1. Atmospheric conditions during high ragweed pollen concentrations in Zagreb, Croatia

    NASA Astrophysics Data System (ADS)

    Prtenjak, Maja Telišman; Srnec, Lidija; Peternel, Renata; Madžarević, Valentina; Hrga, Ivana; Stjepanović, Barbara

    2012-11-01

    We examined the atmospheric conditions favourable to the occurrence of maximum concentrations of ragweed pollen with an extremely high risk of producing allergy. Over the 2002-2009 period, daily pollen data collected in Zagreb were used to identify two periods of high pollen concentration (> 600 grains/m3) for our analysis: period A (3-4 September 2002) and period B (6-7 September 2003). Synoptic conditions in both periods were very similar: Croatia was under the influence of a lower sector high pressure system moving slowly eastward over Eastern Europe. During the 2002-2009 period, this type of weather pattern (on ~ 70% of days), in conjunction with almost non-gradient surface pressure conditions in the area (on ~ 30% of days) characterised days when the daily pollen concentrations were higher than 400 grains/m3. Numerical experiments using a mesoscale model at fine resolution showed successful multi-day simulations reproducing the local topographic influence on wind flow and in reasonable agreement with available observations. According to the model, the relatively weak synoptic flow (predominantly from the eastern direction) allowed local thermal circulations to develop over Zagreb during both high pollen episodes. Two-hour pollen concentrations and 48-h back-trajectories indicated that regional-range transport of pollen grains from the central Pannonian Plain was the cause of the high pollen concentrations during period A. During period B, the north-westward regional-range transport in Zagreb was supplemented significantly by pronounced horizontal recirculation of pollen grains. This recirculation happened within the diurnal local circulation over the city, causing a late-evening increase in pollen concentration.

  2. Achieving high strength and high ductility in magnesium alloy using hard-plate rolling (HPR) process

    PubMed Central

    Wang, Hui–Yuan; Yu, Zhao–Peng; Zhang, Lei; Liu, Chun–Guo; Zha, Min; Wang, Cheng; Jiang, Qi–Chuan

    2015-01-01

    Magnesium alloys are highly desirable for a wide range of lightweight structural components. However, rolling Mg alloys can be difficult due to their poor plasticity, and the strong texture yielded from rolling often results in poor plate forming ability, which limits their further engineering applications. Here we report a new hard-plate rolling (HPR) route which achieves a large reduction during a single rolling pass. The Mg-9Al-1Zn (AZ91) plates processed by HPR consist of coarse grains of 30–60 μm, exhibiting a typical basal texture, fine grains of 1–5 μm and ultrafine (sub) grains of 200–500 nm, both of the latter two having a weakened texture. More importantly, the HPR was efficient in gaining a simultaneous high strength and uniform ductility, i.e., ~371 MPa and ~23%, respectively. The superior properties should be mainly attributed to the cooperation effect of the multimodal grain structure and weakened texture, where the former facilitates a strong work hardening while the latter promotes the basal slip. The HPR methodology is facile and effective, and can avoid plate cracking that is prone to occur during conventional rolling processes. This strategy is applicable to hard-to-deform materials like Mg alloys, and thus has a promising prospect for industrial application. PMID:26603776

  3. Achieving high strength and high ductility in magnesium alloy using hard-plate rolling (HPR) process

    NASA Astrophysics Data System (ADS)

    Wang, Hui–Yuan; Yu, Zhao–Peng; Zhang, Lei; Liu, Chun–Guo; Zha, Min; Wang, Cheng; Jiang, Qi–Chuan

    2015-11-01

    Magnesium alloys are highly desirable for a wide range of lightweight structural components. However, rolling Mg alloys can be difficult due to their poor plasticity, and the strong texture yielded from rolling often results in poor plate forming ability, which limits their further engineering applications. Here we report a new hard-plate rolling (HPR) route which achieves a large reduction during a single rolling pass. The Mg-9Al-1Zn (AZ91) plates processed by HPR consist of coarse grains of 30-60 μm, exhibiting a typical basal texture, fine grains of 1-5 μm and ultrafine (sub) grains of 200-500 nm, both of the latter two having a weakened texture. More importantly, the HPR was efficient in gaining a simultaneous high strength and uniform ductility, i.e., ~371 MPa and ~23%, respectively. The superior properties should be mainly attributed to the cooperation effect of the multimodal grain structure and weakened texture, where the former facilitates a strong work hardening while the latter promotes the basal slip. The HPR methodology is facile and effective, and can avoid plate cracking that is prone to occur during conventional rolling processes. This strategy is applicable to hard-to-deform materials like Mg alloys, and thus has a promising prospect for industrial application.

  4. Achieving high strength and high ductility in magnesium alloy using hard-plate rolling (HPR) process.

    PubMed

    Wang, Hui-Yuan; Yu, Zhao-Peng; Zhang, Lei; Liu, Chun-Guo; Zha, Min; Wang, Cheng; Jiang, Qi-Chuan

    2015-11-25

    Magnesium alloys are highly desirable for a wide range of lightweight structural components. However, rolling Mg alloys can be difficult due to their poor plasticity, and the strong texture yielded from rolling often results in poor plate forming ability, which limits their further engineering applications. Here we report a new hard-plate rolling (HPR) route which achieves a large reduction during a single rolling pass. The Mg-9Al-1Zn (AZ91) plates processed by HPR consist of coarse grains of 30-60 μm, exhibiting a typical basal texture, fine grains of 1-5 μm and ultrafine (sub) grains of 200-500 nm, both of the latter two having a weakened texture. More importantly, the HPR was efficient in gaining a simultaneous high strength and uniform ductility, i.e., ~371 MPa and ~23%, respectively. The superior properties should be mainly attributed to the cooperation effect of the multimodal grain structure and weakened texture, where the former facilitates a strong work hardening while the latter promotes the basal slip. The HPR methodology is facile and effective, and can avoid plate cracking that is prone to occur during conventional rolling processes. This strategy is applicable to hard-to-deform materials like Mg alloys, and thus has a promising prospect for industrial application.

  5. New York State Superintendents and Board Presidents Attitudes on Superintendent Responsibilities in High-Achieving and Low-Achieving School Districts

    ERIC Educational Resources Information Center

    Murphy, Matthew J.

    2009-01-01

    The purpose of this study is to determine the perceptions of New York State superintendents and board presidents in high-achieving and low-achieving school districts on the six superintendent leadership responsibilities identified by Waters and Marzano (2006) and their relationship to improving student achievement: (1) creating research-relevant…

  6. Understanding and Reversing Underachievement, Low Achievement, and Achievement Gaps among High-Ability African American Males in Urban School Contexts

    ERIC Educational Resources Information Center

    Ford, Donna Y.; Moore, James L., III

    2013-01-01

    This article focuses on the achievement gap, with attention devoted to underachievement and low achievement among African American males in urban school contexts. More specifically, the article explains problems and issues facing or confronting these Black male students in urban education settings. A central part of this discussion is grounded in…

  7. Gender and High School Chemistry: Student Perceptions on Achievement in a Selective Setting

    ERIC Educational Resources Information Center

    Cousins, Andrew; Mills, Martin

    2015-01-01

    This paper reports on research undertaken in a middle-class Australian school. The focus of the research was on the relationship between gender and students' engagement with high school chemistry. Achievement data from many OECD [Organisation for Economic Co-operation and Development] countries suggest that middle-class girls are achieving equally…

  8. Achievement Motivation in High School: Contrasting Theoretical Models in the Classroom.

    ERIC Educational Resources Information Center

    Garcia-Celay, I. Montero; Tapia, J. Alonso

    1992-01-01

    Three models of achievement motivation in the classroom are contrasted. Results with 155 high school students suggest that the model of C. S. Dweck and E. S. Elliott offers a better explanation of the relationships among achievement motivation, attributions, emotional reactions, expectancies, and performance than do the other models. (SLD)

  9. Predicting Early Academic Failure in High School from Prior Academic Achievement, Psychosocial Characteristics, and Behavior

    ERIC Educational Resources Information Center

    Casillas, Alex; Robbins, Steve; Allen, Jeff; Kuo, Yi-Lung; Hanson, Mary Ann; Schmeiser, Cynthia

    2012-01-01

    The authors examined the differential effects of prior academic achievement, psychosocial, behavioral, demographic, and school context factors on early high school grade point average (GPA) using a prospective study of 4,660 middle-school students from 24 schools. The findings suggest that (a) prior grades and standardized achievement are the…

  10. Accelerated Mathematics and High-Ability Students' Math Achievement in Grades Three and Four

    ERIC Educational Resources Information Center

    Stanley, Ashley M.

    2011-01-01

    The purpose of this study was to explore the relationship between the use of a computer-managed integrated learning system entitled Accelerated Math (AM) as a supplement to traditional mathematics instruction on achievement as measured by TerraNova achievement tests of third and fourth grade high-ability students. Gender, socioeconomic status, and…

  11. An Analysis of Mathematics Course Sequences for Low Achieving Students at a Comprehensive Technical High School

    ERIC Educational Resources Information Center

    Edge, D. Michael

    2011-01-01

    This non-experimental study attempted to determine how the different prescribed mathematic tracks offered at a comprehensive technical high school influenced the mathematics performance of low-achieving students on standardized assessments of mathematics achievement. The goal was to provide an analysis of any statistically significant differences…

  12. The Impact of Charter Schools on Promoting High Levels of Mathematics Achievement

    ERIC Educational Resources Information Center

    Plucker, Jonathan A.; Makel, Matthew C.; Rapp, Kelly E.

    2007-01-01

    This study compares achievement levels for high ability students attending charter schools and students in traditional public schools in Georgia. Researchers examined student achievement (as assessed by the state's Criterion-Referenced Competency Tests) using three comparison groups: students in the closest traditional schools with similar grade…

  13. A Quantitative Comparison of Pennsylvania High School Student Achievement by Middle States Association's Accreditation Status

    ERIC Educational Resources Information Center

    Johnson, Christopher A.

    2012-01-01

    As public school accountability for student achievement has continued to increase, prior to and as a result of the No Child Left Behind Act of 2001, schools have sought ways of bringing new instructional services to their students to raise their levels of achievement. Some Pennsylvania public high schools have attempted to improve student…

  14. Unforgiving Confucian Culture: A Breeding Ground for High Academic Achievement, Test Anxiety and Self-Doubt?

    ERIC Educational Resources Information Center

    Stankov, Lazar

    2010-01-01

    This paper reviews findings from several studies that contribute to our understanding of cross-cultural differences in academic achievement, anxiety and self-doubt. The focus is on comparisons between Confucian Asian and European regions. Recent studies indicate that high academic achievement of students from Confucian Asian countries is…

  15. Instructional, Transformational, and Managerial Leadership and Student Achievement: High School Principals Make a Difference

    ERIC Educational Resources Information Center

    Valentine, Jerry W.; Prater, Mike

    2011-01-01

    This statewide study examined the relationships between principal managerial, instructional, and transformational leadership and student achievement in public high schools. Differences in student achievement were found when schools were grouped according to principal leadership factors. Principal leadership behaviors promoting instructional and…

  16. Cohort versus Non-Cohort High School Students' Math Performance: Achievement Test Scores and Coursework

    ERIC Educational Resources Information Center

    Parke, Carol S.; Keener, Dana

    2011-01-01

    The purpose of this study is to compare multiple measures of mathematics achievement for 1,378 cohort students who attended the same high school in a district from 9th to 12th grade with non-cohort students in each grade level. Results show that mobility had an impact on math achievement. After accounting for gender, ethnicity, and SES, adjusted…

  17. Process for producing high-concentration slurry of coal

    SciTech Connect

    Nakaoji, K.; Itoh, H.; Kamao, M.; Takao, Sh.; Tatsumi, Sh.

    1985-02-19

    High concentrated coal-water slurry is produced by coarsely crushing coal, thereafter pulverizing the coarsely crushed coal, together with water and a slurry dispersant, according to necessity, in a wet-type ball mill, and feeding back one portion of the finely pulverized coal slurry thus obtained into the inlet of the wet-type ball mill.

  18. Waste to Energy Potential - A High Concentration Anaerobic Bioreactor

    DTIC Science & Technology

    2012-05-23

    output • Uses the organic portion of solid waste (such as food waste , paper products, and agricultural waste ) to fuel an anaerobic digestion ...Sustainability Symposium & Exhibition Anaerobic Digestion • What does it do? • Offers sustainability by addressing renewable energy, waste ... Waste to Energy Potential – A High Concentration Anaerobic Bioreactor Presenter: Scott Murphy & Rebecca Robbennolt ARCADIS/Malcolm Pirnie Date

  19. Polyaspartamide derivative nanoparticles with tunable surface charge achieve highly efficient cellular uptake and low cytotoxicity.

    PubMed

    Xu, Min; Zhao, Yuefang; Feng, Min

    2012-08-07

    Cationic nanocarrier mediated intracellular therapeutic agent delivery acts as a double-edged sword: the carriers promote cellular uptake, but interact nonspecifically and strongly with negatively charged endogenic proteins and cell membranes, which results in aggregates and high cytotoxicity. The present study was aimed at exploring zwitterionic polyaspartamide derivative nanoparticles for efficient intracellular delivery with low cytotoxicity. Poly(aspartic acid) partially grafted tetraethylenepentamine (PASP-pg-TEPA) with different isoelectric points (IEPs) was synthesized. The PASP-pg-TEPA formed zwitterionic nanoparticles with an irregular core and a well-defined shell structure in aqueous medium. Their particle size decreased from about 300 to 80 nm with an increase of the IEP from 7.5 to 9.1. The surface charge of the PASP-pg-TEPA nanoparticles could be tuned from positive to negative with a change of the pH of the medium. The nanoparticles with an IEP above 8.5 exhibited good stability under simulated physiological conditions. It was noted that the zwitterionic PASP-pg-TEPA nanoparticles displayed highly efficient cellular uptake in HeLa cells (approximately 99%) in serum-containing medium and did not adversely affect the cell viability at concentrations up to 1 mg/mL. Furthermore, thermodynamic analysis using isothermal titration calorimetry provided direct evidence that these zwitterionic nanoparticles had low binding affinities for serum protein. Therefore, the zwitterionic PASP-pg-TEPA nanoparticles could overcome limitations of cationic nanocarriers and achieve efficient intracellular delivery with low cytotoxicity.

  20. On the concentration structure of high-concentration constant-volume fluid mud gravity currents

    NASA Astrophysics Data System (ADS)

    Jacobson, M. R.; Testik, F. Y.

    2013-01-01

    An exhaustive laboratory experimental campaign was undertaken in order to elucidate the concentration structure of two-dimensional constant-volume non-Newtonian fluid mud gravity currents. Two sets of experiments were conducted in a lock-exchange tank. The first set of experiments involved measuring the vertical concentration profiles using a siphoning technique; the second set involved auxiliary visual observations. The first set of experiments consisted of 32 experimental runs for four different experimental conditions, with an array of siphoned samples being withdrawn throughout the head and body of the gravity current. From these samples, vertical concentration profiles occurring in constant-volume fluid mud gravity currents were classified and the underlying physical processes that led to the occurrence of observed profiles were discussed. Furthermore, the functional form of the vertical concentration profiles within the head of relatively low-initial-concentration gravity currents was proposed. The relatively high-initial-concentration gravity currents revealed the presence of a lutocline in the current head and body, the presence of which was observed for constant-flux release gravity currents. To our knowledge, this is the first measurement of a lutocline in constant-volume gravity currents. Abrupt transitions, a phenomenon in which the bulk of the suspended sediment in the propagating gravity current drops out, were observed through the concentration profiles and through 15 auxiliary visual experimental runs. It was found that abrupt transitions were caused by the presence of a lutocline. The entrainment of ambient water resulting in the dilution of the gravity current at different concentration contours has been quantified. In a previous work by the authors of this study, it was shown that the initial reduced gravity is directly proportional to the growth rate of the visual area of the two-dimensional current. The analysis of our experimental observations

  1. [Toxic effects of high concentrations of ammonia on Euglena gracilis].

    PubMed

    Liu, Yan; Shi, Xiao-Rong; Cui, Yi-Bin; Li, Mei

    2013-11-01

    Ammonia is among the common contaminants in aquatic environments. The present study aimed at evaluation of the toxicity of ammonia at high concentration by detecting its effects on the growth, pigment contents, antioxidant enzyme activities, and DNA damage (comet assay) of a unicellular microalga, Euglena gracilis. Ammonia restrained the growth of E. gracilis, while at higher concentrations, ammonia showed notable inhibition effect, the growth at 2 000 mg x L(-1) was restrained to 55.7% compared with that of the control; The contents of photosynthetic pigments and protein went up with increasing ammonia dosage and decreased when the ammonia concentration was above 1000 mg x L(-1); In addition, there was an obvious increase in SOD and POD activities, at higher concentration (2 000 mg x L(-1)), activities of SOD and POD increased by 30.7% and 49.4% compared with those of the control, indicating that ammonia could promote activities of antioxidant enzymes in E. gracilis; The degree of DNA damage observed in the comet assay increased with increasing ammonia concentration, which suggested that high dose of ammonia may have potential mutagenicity on E. gracilis.

  2. Impacts of comprehensive reading instruction on diverse outcomes of low- and high-achieving readers.

    PubMed

    Guthrie, John T; McRae, Angela; Coddington, Cassandra S; Lutz Klauda, Susan; Wigfield, Allan; Barbosa, Pedro

    2009-01-01

    Low-achieving readers in Grade 5 often lack comprehension strategies, domain knowledge, word recognition skills, fluency, and motivation to read. Students with such multiple reading needs seem likely to benefit from instruction that supports each of these reading processes. The authors tested this expectation experimentally by comparing the effects of Concept-Oriented Reading Instruction (CORI) with traditional instruction (TI) on several outcomes in a 12-week intervention for low achievers and high achievers. Low achievers in the CORI group were afforded explicit instruction, leveled texts, and motivation support. Compared with TI students, CORI students scored higher on posttest measures of word recognition speed, reading comprehension on the Gates-MacGinitie Reading Test, and ecological knowledge. CORI was equally effective for lower achievers and higher achievers. Explicitly supporting multiple aspects of reading simultaneously appeared to benefit diverse learners on a range of reading outcomes.

  3. Unusually high indoor radon concentrations from a giant rock slide.

    PubMed

    Ennemoser, O; Ambach, W; Brunner, P; Schneider, P; Oberaigner, W; Purtscheller, F; Stingl, V; Keller, G

    1994-07-18

    In a village in western Tyrol, Austria (Umhausen, approximately 2600 inhabitants) unusually high indoor radon concentrations were measured. The medians were found to be 3750 Bq/m3 (basements) and 1160 Bq/m3 (ground floors) in winter, and 361 Bq/m3 (basements) and 210 Bq/m3 (ground floors) in summer. Maximum radon concentrations of up to 274,000 Bq/m3 were registered. The unusually high radon concentrations are due to the geology of the locality. The part of Umhausen with the highest radon concentrations is built on an alluvial fan of a giant rock slide (granitic gneiss). Measurements of the radon exhalation rate from soil showed a median of 0.4 Bq/m2/s, measurements of the radium content of rock samples yielded a median of 125 Bq/kg. The material of the rock slide is heavily fractured so that an elevated emanating power and an increased diffusion coefficient for radon in soil must be assumed. Given a diffusion coefficient of 8 x 10(-6) m2/s and an emanating power of 0.3, the median exhalation rate of 0.4 Bq/m2/s is obtained at a radium concentration of 125 Bq/kg. The rock slide is therefore considered to be the main source of radon. The abnormally high radon concentrations in Umhausen coincide with a statistically significant increase in lung cancer mortality (age and sex standardized mortality rate = 3.9, 95% C.I.: 2.9-5.1); the control population is the population of the entire Tyrol (630,000 inhabitants).

  4. Understanding the Elements of Operational Reliability: A Key for Achieving High Reliability

    NASA Technical Reports Server (NTRS)

    Safie, Fayssal M.

    2010-01-01

    This viewgraph presentation reviews operational reliability and its role in achieving high reliability through design and process reliability. The topics include: 1) Reliability Engineering Major Areas and interfaces; 2) Design Reliability; 3) Process Reliability; and 4) Reliability Applications.

  5. A Quantitative Literature Review of Cooperative Learning Effects on High School and College Chemistry Achievement.

    ERIC Educational Resources Information Center

    Bowen, Craig W.

    2000-01-01

    Describes meta-analysis, a quantitative approach to conducting literature reviews. Illustrates the power of this technique by reporting the quantitative effects of cooperative learning on chemistry achievement in high school and college classes. (Contains 32 references.) (WRM)

  6. Manufacture of concentrated, lipid-based oxygen microbubble emulsions by high shear homogenization and serial concentration.

    PubMed

    Thomson, Lindsay M; Polizzotti, Brian D; McGowan, Frances X; Kheir, John N

    2014-05-26

    Gas-filled microbubbles have been developed as ultrasound contrast and drug delivery agents. Microbubbles can be produced by processing surfactants using sonication, mechanical agitation, microfluidic devices, or homogenization. Recently, lipid-based oxygen microbubbles (LOMs) have been designed to deliver oxygen intravenously during medical emergencies, reversing life-threatening hypoxemia, and preventing subsequent organ injury, cardiac arrest, and death. We present methods for scaled-up production of highly oxygenated microbubbles using a closed-loop high-shear homogenizer. The process can produce 2 L of concentrated LOMs (90% by volume) in 90 min. Resulting bubbles have a mean diameter of ~2 μm, and a rheologic profile consistent with that of blood when diluted to 60 volume %. This technique produces LOMs in high capacity and with high oxygen purity, suggesting that this technique may be useful for translational research labs.

  7. Structure and rheology of highly concentrated emulsions: a modern look

    NASA Astrophysics Data System (ADS)

    Malkin, A. Ya; Kulichikhin, V. G.

    2015-08-01

    The review concerns modern physicochemical, chemical and physical approaches to research into structural features that determine the rheological properties of highly concentrated emulsions. The structures and properties of various systems (suspensions, emulsions as well as transient forms including micellar colloidal solutions) are considered. The formation of highly concentrated emulsions is treated as the concentration glass transition leading to suppression of the molecular and supermolecular mobility and, subsequently, to the existence of a solid-like state of the systems in question. The emphasis is placed on analysis of visco-plasticity which manifests itself in the possibility for emulsions (unlike suspensions) to undergo irreversible deformation (to flow) at stresses exceeding some threshold (critical value) called the yield stress. The thixotropic nature of the transition through the yield stress, governed by the kinetics of the breakup/recovery of the inherent structure is considered in detail. It has been shown that structure formation in highly concentrated emulsions can extend to a macroscopic level and result in the onset of heterogeneity of a flow in the form of shear bands. The bibliography includes 202 references.

  8. Review of silicon solar cells for high concentrations

    NASA Astrophysics Data System (ADS)

    Schwartz, R. J.

    1982-06-01

    The factors that limit the performance of high concentration silicon solar cells are reviewed. The design of a conventional high concentration cell is discussed, together with the present state of the art. Unconventional cell designs that have been proposed to overcome the limitations of the conventional design are reviewed and compared. The current status of unconventional cells is reviewed. Among the unconventional cells discussed are the interdigitated back-contact cell, the double-sided cell, the polka dot cell, and the V-groove cell. It is noted that all the designs for unconventional cells require long diffusion lengths for high efficiency operation, even though the demands in this respect are less for those cells with the optical path longer than the diffusion path.

  9. Novel bioevaporation process for the zero-discharge treatment of highly concentrated organic wastewater.

    PubMed

    Yang, Benqin; Zhang, Lei; Lee, Yongwoo; Jahng, Deokjin

    2013-10-01

    A novel process termed as bioevaporation was established to completely evaporate wastewater by metabolic heat released from the aerobic microbial degradation of the organic matters contained in the highly concentrated organic wastewater itself. By adding the glucose solution and ground food waste (FW) into the biodried sludge bed, the activity of the microorganisms in the biodried sludge was stimulated and the water in the glucose solution and FW was evaporated. As the biodegradable volatile solids (BVS) concentration in wastewater increased, more heat was produced and the water removal ratio increased. When the volatile solids (VS) concentrations of both glucose and ground FW were 120 g L(-1), 101.7% and 104.3% of the added water was removed, respectively, by completely consuming the glucose and FW BVS. Therefore, the complete removal of water and biodegradable organic contents was achieved simultaneously in the bioevaporation process, which accomplished zero-discharge treatment of highly concentrated organic wastewater.

  10. Stable, concentrated solutions of high molecular weight polyaniline and articles therefrom

    DOEpatents

    Mattes, Benjamin R.; Wang, Hsing-Lin

    2000-01-01

    Stable, concentrated solutions of high molecular weight polyaniline. In order to process high quality fibers and other articles possessing good mechanical properties, it is known that solution concentrations of the chosen polymer should be in the range from 15-30% (w/w). Moreover, it is desirable to use the highest molecular weight consistent with the solubility properties of the polymer. However, such solutions are inherently unstable, forming gels before processing can be achieved. The present invention describes the addition gel inhibitors (GIs) to the polymer solution, thereby permitting high concentrations (>15% (w/w)) of high molecular weight ((M.sub.w)>120,000, and (M.sub.n)>30,000) emeraldine base (EB) polyaniline to be dissolved. Secondary amines have been used for this purpose in concentrations which are small compared to those which might otherwise be used in a cosolvent role therefor. The resulting solutions are useful for generating excellent fibers, films, coatings and other objects, since the solutions are stable for significant time periods, and the GIs are present in too small concentrations to cause polymer deterioration. It is demonstrated that the GIs found to be useful do not act as cosolvents, and that gelation times of the solutions are directly proportional to the concentration of GI. In particular, there is a preferred concentration of GI, which if exceeded causes structural and electrical conductivity degradation of resulting articles. Heating of the solutions significantly improves solubility.

  11. Stable, concentrated solutions of high molecular weight polyaniline and articles therefrom

    DOEpatents

    Mattes, Benjamin R.; Wang, Hsing-Lin

    1999-11-09

    Stable, concentrated solutions of high molecular weight polyaniline. In order to process high quality fibers and other articles possessing good mechanical properties, it is known that solution concentrations of the chosen polymer should be in the range from 15-30% (w/w). Moreover, it is desirable to use the highest molecular weight consistent with the solubility properties of the polymer. However, such solutions are inherently unstable, forming gels before processing can be achieved. The present invention describes the addition gel inhibitors (GIs) to the polymer solution, thereby permitting high concentrations (between 15% and 30% (w/w)) of high molecular weight ((M.sub.w)>120,000, and (M.sub.n)>30,000) emeraldine base (EB) polyaniline to be dissolved. Secondary amines have been used for this purpose in concentrations which are small compared to those which might otherwise be used in a cosolvent role therefor. The resulting solutions are useful for generating excellent fibers, films, coatings and other objects, since the solutions are stable for significant time periods, and the GIs are present in too small concentrations to cause polymer deterioration. It is demonstrated that the GIs found to be useful do not act as cosolvents, and that gelation times of the solutions are directly proportional to the concentration of GI. In particular, there is a preferred concentration of GI, which if exceeded causes structural and electrical conductivity degradation of resulting articles. Heating of the solutions significantly improves solubility.

  12. A Comparison of Emotional-Motivational (A-R-D Theory) Personality Characteristics in Learning Disabled, Normal Achieving, and High Achieving Children.

    ERIC Educational Resources Information Center

    Hufano, Linda D.

    The study examined emotional-motivational personality characteristics of 15 learning disabled, 15 normal achieving, and 15 high achieving students (grades 3-5). The study tested the hypothesis derived from the A-R-D (attitude-reinforcer-discriminative) theory of motivation that learning disabled (LD) children differ from normal and high achieving…

  13. The Outward Bound Bridging Course for Low-Achieving High School Males: Effect on Academic Achievement and Multidimensional Self-Concepts.

    ERIC Educational Resources Information Center

    Marsh, Herbert W.; Richards, Garry

    The Outward Bound Bridging Course is a 6-week residential program designed to improve academic achievement and self-concepts in low-achieving high school males. During 1980-1984, five courses were conducted for 66 Australian high school males. Most of them were ninth grade students, chosen on the basis of poor academic performance, an apparent…

  14. High Actin Concentrations in Brain Dendritic Spines and Postsynaptic Densities

    NASA Astrophysics Data System (ADS)

    Matus, Andrew; Ackermann, Marcel; Pehling, Gundula; Randolph Byers, H.; Fujiwara, Keigi

    1982-12-01

    Antibodies against actin were used to corroborate the presence of actin as a major component protein of isolated brain postsynaptic densities. The same antibodies also were used as an immunohistochemical stain to study the distribution of actin in sections of intact brain tissue. This showed two major sites where actin is concentrated: smooth muscle cells around blood vessels and postsynaptic sites. In the postsynaptic area the highest concentration of actin occurs in postsynaptic densities and there also is intense staining in the surrounding cytoplasm, especially within dendritic spines. Antiactin staining was much weaker in other parts of neurons and in glial cells. The high concentration of actin in dendritic spines may be related to shape changes that these structures have been found to undergo in response to prolonged afferent stimulation.

  15. Decomposition of high concentration SF6 using an electron beam

    NASA Astrophysics Data System (ADS)

    Son, Youn-Suk; Lee, Sung-Joo; Choi, Chang Yong; Park, Jun-Hyeong; Kim, Tak-Hyun; Jung, In-Ha

    2016-07-01

    In this study, high concentration SF6 (2-10%) was decomposed using an electron beam irradiation. Various influential factors were investigated to improve the destruction and removal efficiency (DRE) of SF6. The initial concentrations of SF6, absorbed doses, SF6/H2 ratios and retention times were the main factors of concern. As a result, the DRE increased as the adsorbed dose and retention time increased. The DRE of SF6 also increased up to 20% approximately when H2 was added to the reaction mixture. On the other hand, the DRE of SF6 decreased as initial concentrations of SF6 increased. Finally, the main by-product formed from SF6 decomposition by the electron beam was HF.

  16. Concentration measurement of yeast suspensions using high frequency ultrasound backscattering.

    PubMed

    Elvira, Luis; Vera, Pedro; Cañadas, Francisco Jesús; Shukla, Shiva Kant; Montero, Francisco

    2016-01-01

    This work proposes the use of an ultrasound based technique to measure the concentration of yeasts in liquid suspension. This measurement was achieved by the detection and quantification of ultrasonic echoes backscattered by the cells. More specifically, the technique was applied to the detection and quantification of Saccharomyces cerevisiae. A theoretical approach was proposed to get the average density and sound speed of the yeasts, which were found to be 1116 kg/m(3) and 1679 m/s, respectively. These parameters were needed to model the waves backscattered by each single cell. A pulse-echo arrangement working around 50 MHz, being able to detect echoes from single yeasts was used to characterize experimentally yeast solutions from 10(2) to 10(7)cells/ml. The Non-negative Matrix Factorization denoising technique was applied for data analysis. This technique required a previous learning of the spectral patterns of the echoes reflected from yeasts in solution and the base noise from the liquid medium. Comparison between pulse correlation (without denoising) and theoretical and experimental pattern learning was made to select the best signal processing. A linear relation between ultrasound output and concentration was obtained with correlation coefficient R(2)=0.996 for the experimental learning. Concentrations from 10(4) to 10(7)cells/ml were detected above the base noise. These results show the viability of using the ultrasound backscattering technique to detect yeasts and measure their concentration in liquid cultures, improving the sensitivity obtained using spectrophotometric methods by one order of magnitude.

  17. Performance of solmacs, a high PV solar concentrator with efficient optics

    NASA Astrophysics Data System (ADS)

    Thibert, T.; Hellin, M.-L.; Loicq, J.; Mazy, E.; Jacques, L.; Verstraeten, D.; Gillis, J.-M.; Languy, F.; Emmerechts, C.; Beeckman, E.; Habraken, S.; Lecat, J.-H.

    2012-10-01

    A new solar panel with high concentration photovoltaic technology (x700) has been designed, prototyped and tested in the SOLMACS project. The quality of concentrating optics is a key factor for high module efficiency. Therefore new dedicated PMMA Fresnel lenses were studied and produced by injection molding. Lens design, material and production process were optimized to achieve a high optical yield of 86%. Thorough lens performance assessment in optical laboratory was completed with lifetime UV aging tests. Another important aspect is the thermal control of the hot spot created under the solar cell that receives the concentrated flux of 700 Suns. A dedicated heat spreader was developed to achieve passive thermal control with minimum mass and cost. This was supported by thermal models and tests at both cell and module level. 35% triple junction cells were implemented in the module. Micro-assembly technologies were used for the cell packaging and electrical connections. In support to the research, a continuous solar simulator was designed and built to assess the system performance, both at component and module level. The concentrator developments were integrated in a prototype and tested both indoor with the simulator and outdoor on the CSL solar test platform. The overall efficiency of the PV concentrator module is 28.5%.

  18. Acute toxicity of high concentrations of carbon dioxide in rats.

    PubMed

    Muijser, H; van Triel, J J; Duistermaat, E; Bos, P M J

    2014-07-01

    Subterranean storage of carbon dioxide (CO2) has been proposed to diminish atmospheric increases of this greenhouse gas. To contribute to risk assessment of accidental release associated with handling, transport and storage, rats were exposed to high concentrations (targets 40, 43 and 50 volume %) of CO2. The oxygen concentrations dropped as a result, but were not supplemented. For each concentration, pairs of animals were exposed for different exposure durations to derive an exposure concentration-duration relation in which mortality is described as a function of C(n)×t (probit relation). A very high "n" value for the probit function could be derived from the data obtained at 40% and 43% CO2, which indicates that for exposure durations longer than 30 min the LC50 decreases hardly with increasing exposure duration. Below 30 min the LC50 seemed to increase with decreasing exposure durations. The variability in the data of 43% and 50% CO2, however, did not allow to derive a meaningful value of "n".

  19. Copper uptake by Eichhornia crassipes exposed at high level concentrations.

    PubMed

    Melignani, Eliana; de Cabo, Laura Isabel; Faggi, Ana María

    2015-06-01

    The objective of this study was to assess the growth of water hyacinth (Eichhornia crassipes) and its ability to accumulate Cu from polluted water with high Cu concentrations and a mixture of other contaminants under short-term exposure, in order to use this species for the remediation of highly contaminated sites. Two hydroponic experiments were performed under greenhouse conditions for 7 days. One of them consisted of growing water hyacinth in Hoagland solution supplemented with 15 or 25 mg Cu/L and a control. The other one contained water hyacinth growing in polluted river water supplemented with 15 mg Cu/L and a control. Cu was accumulated principally in roots. The maximum Cu concentration was 23,387.2 mg/kg dw in the treatment of 25 mg Cu/L in Hoagland solution. Cu translocation from roots to leaves was low. The mixture of 15 mg Cu/L with polluted water did not appear to have toxic effects on the water hyacinth. This plant showed a remarkable uptake capacity under elevated Cu concentrations in a mixture of pollutants similar to pure industrial effluents in a short time of exposure. This result has not been reported before, to our knowledge. This species is suitable for phytoremediation of waters subject to discharge of mixed industrial effluents containing elevated Cu concentrations (≥15 mg Cu/L), as well as nutrient-rich domestic wastewaters.

  20. Race and Ethnic Differences in College Achievement: Does High School Attended Matter?

    PubMed Central

    Fletcher, Jason M.; Tienda, Marta

    2012-01-01

    This paper uses 10 years of enrollment data at four Texas public universities to examine whether, to what extent, and in what ways high school attended contributes to racial and ethnic differences in college achievement. Like previous studies, we show that controlling for observable pre-college achievement variables (e.g. test scores, class rank) shrinks, but does not eliminate, sizable racial differences in college achievement. Fixed-effects models that take into account differences across high schools that minority and nonminority youth attend largely eliminate, and often reverse, black-white and Hispanic-white gaps in several measures of college achievement. Our results, which are quite robust across universities of varying selectivity, illustrate how high school quality foments race and ethnic inequality in postsecondary achievement. Leveling inequities in the quality of high schools that minority students attend is a long-run agenda, but remediation programs that compensate for instructional shortfalls at low performing high schools may help close achievement gaps in the interim. PMID:23136447

  1. Race and Ethnic Differences in College Achievement: Does High School Attended Matter?

    PubMed

    Fletcher, Jason M; Tienda, Marta

    2010-01-01

    This paper uses 10 years of enrollment data at four Texas public universities to examine whether, to what extent, and in what ways high school attended contributes to racial and ethnic differences in college achievement. Like previous studies, we show that controlling for observable pre-college achievement variables (e.g. test scores, class rank) shrinks, but does not eliminate, sizable racial differences in college achievement. Fixed-effects models that take into account differences across high schools that minority and nonminority youth attend largely eliminate, and often reverse, black-white and Hispanic-white gaps in several measures of college achievement. Our results, which are quite robust across universities of varying selectivity, illustrate how high school quality foments race and ethnic inequality in postsecondary achievement. Leveling inequities in the quality of high schools that minority students attend is a long-run agenda, but remediation programs that compensate for instructional shortfalls at low performing high schools may help close achievement gaps in the interim.

  2. Exceptionally omnidirectional broadband light harvesting scheme for multi-junction concentrator solar cells achieved via ZnO nanoneedles.

    PubMed

    Yeh, Li-Ko; Tian, Wei-Cheng; Lai, Kun-Yu; He, Jr-Hau

    2016-12-14

    GaInP/GaAs/Ge triple-junction concentrator solar cells with significant efficiency enhancement were demonstrated with antireflective ZnO nanoneedles. The novel nanostructure was attained with a Zn(NO3)2-based solution containing vitamin C. Under one sun AM 1.5G solar spectrum, conversion efficiency of the triple-junction device was improved by 23.7% via broadband improvement in short-circuit currents of 3 sub-cells after the coverage by the nanoneedles with a graded refractive index profile. The efficiency enhancement further went up to 45.8% at 100 suns. The performance boost through the nanoneedles also became increasingly pronounced in the conditions of high incident angles and the cloudy weather, e.g. 220.0% of efficiency enhancement was observed at the incident angle of 60°. These results were attributed to the exceptional broadband omnidirectionality of the antireflective nanoneedles.

  3. Exceptionally omnidirectional broadband light harvesting scheme for multi-junction concentrator solar cells achieved via ZnO nanoneedles

    PubMed Central

    Yeh, Li-Ko; Tian, Wei-Cheng; Lai, Kun-Yu; He, Jr-Hau

    2016-01-01

    GaInP/GaAs/Ge triple-junction concentrator solar cells with significant efficiency enhancement were demonstrated with antireflective ZnO nanoneedles. The novel nanostructure was attained with a Zn(NO3)2-based solution containing vitamin C. Under one sun AM 1.5G solar spectrum, conversion efficiency of the triple-junction device was improved by 23.7% via broadband improvement in short-circuit currents of 3 sub-cells after the coverage by the nanoneedles with a graded refractive index profile. The efficiency enhancement further went up to 45.8% at 100 suns. The performance boost through the nanoneedles also became increasingly pronounced in the conditions of high incident angles and the cloudy weather, e.g. 220.0% of efficiency enhancement was observed at the incident angle of 60°. These results were attributed to the exceptional broadband omnidirectionality of the antireflective nanoneedles. PMID:27966621

  4. Exceptionally omnidirectional broadband light harvesting scheme for multi-junction concentrator solar cells achieved via ZnO nanoneedles

    NASA Astrophysics Data System (ADS)

    Yeh, Li-Ko; Tian, Wei-Cheng; Lai, Kun-Yu; He-Hau, Jr.

    2016-12-01

    GaInP/GaAs/Ge triple-junction concentrator solar cells with significant efficiency enhancement were demonstrated with antireflective ZnO nanoneedles. The novel nanostructure was attained with a Zn(NO3)2-based solution containing vitamin C. Under one sun AM 1.5G solar spectrum, conversion efficiency of the triple-junction device was improved by 23.7% via broadband improvement in short-circuit currents of 3 sub-cells after the coverage by the nanoneedles with a graded refractive index profile. The efficiency enhancement further went up to 45.8% at 100 suns. The performance boost through the nanoneedles also became increasingly pronounced in the conditions of high incident angles and the cloudy weather, e.g. 220.0% of efficiency enhancement was observed at the incident angle of 60°. These results were attributed to the exceptional broadband omnidirectionality of the antireflective nanoneedles.

  5. High-efficiency GaAs concentrator space cells

    NASA Technical Reports Server (NTRS)

    Werthen, J. G.; Virshup, G. F.; Macmillan, H. F.; Ford, C. W.; Hamaker, H. C.

    1987-01-01

    High efficiency Al sub x Ga sub 1-x As/GaAs heteroface solar concentrator cells have been developed for space applications. The cells, which were grown using metalorganic chemical vapor deposition (MOCVD), have been fabricated in both the p-n and n-p configurations. Magnesium and zinc are used as the p-type dopants, and Se is used as the n-type dopant. The space cells, which are designed for use in a Cassegrainian concentrator operating at 100 suns, AMO, have a circular illuminated area 4 mm in diameter on a 5 mm by 5 mm cell. These cells have exhibited flash-tested efficiencies as high as 23.6 percent at 28 C and 21.6 percent at 80 C.

  6. Particle sedimentation monitoring in high-concentration slurries

    NASA Astrophysics Data System (ADS)

    Nagasawa, Yoshihiro; Kato, Zenji; Tanaka, Satoshi

    2016-11-01

    In this study, the sedimentation states of particles in high-concentration slurries were elucidated by monitoring their internal states. We prepared transparent high-concentration silica slurries by adjusting the refractive index of the aqueous glycerol liquid in which the particles were dispersed to match that of the silica particles. In addition, a fluorescent dye was dissolved in the liquid. Then, we directly observed the individual and flocculated particles in the slurries during sedimentation by confocal laser scanning fluorescent microscopy. The particles were found to sediment very slowly while exhibiting fluctuating motion. The particle sedimentation rate in the high-concentration slurry with the aqueous glycerol solution (η =0.068 Pa. s ) and a particle volume fraction on the order of 0.3 was determined to be 1.58 ± 0.66 μ m. min-1 on the basis of the obtained image sequences for 24.9 h. In-situ observation provides a large amount of information about the sedimentation behavior of particles in condensed matter.

  7. Study of upconversion in PCFs with high erbium concentration

    NASA Astrophysics Data System (ADS)

    Berdejo, Víctor; Vallés, Juan A.; Rebolledo, Miguel Á.; Diez, Antonio; Martin, Juan C.; Sanchez-Martin, José A.; Álvarez, José M.; Andrés, Miguel V.

    2011-09-01

    We report on a comparison of characterization techniques for high concentration erbium-doped photonic crystal fibres (PCFs). A highly erbium-doped-silica PCF was fabricated and an amplifier based on the PCF was built. Then, measurements on the amplifier output optical powers were carried out. To model the amplifier, three different formalisms were assumed for the Er3+-ion upconversion mechanism and the numerical results were fitted to the experimental ones. The sets of best-fit parameters are compared and the use of these techniques for active PCF characterisation is discussed.

  8. Social Goals, Social Status, and Problem Behavior among Low-Achieving and High-Achieving Adolescents from Rural Schools

    ERIC Educational Resources Information Center

    Ludden, Alison Bryant

    2012-01-01

    The current research examines how social goals and perceptions of what is needed for social status at school relate to school misbehavior and substance use among rural adolescents (N = 683). Results indicate that social goals and perceptions of social status have differential links to problem behaviors depending upon adolescents' achievement.…

  9. Wet oxidation of real coke wastewater containing high thiocyanate concentration.

    PubMed

    Oulego, Paula; Collado, Sergio; Garrido, Laura; Laca, Adriana; Rendueles, Manuel; Díaz, Mario

    2014-01-01

    Coke wastewaters, in particular those with high thiocyanate concentrations, represent an important environmental problem because of their very low biodegradability. In this work, the treatment by wet oxidation of real coke wastewaters containing concentrations of thiocyanate above 17 mM has been studied in a 1-L semi-batch reactor at temperatures between 453 and 493 K, with total oxygen pressures in the range of 2.0-8.0 MPa. A positive effect of the matrix of real coke wastewater was observed, resulting in faster thiocyanate degradation than was obtained with synthetic wastewaters. Besides, the effect of oxygen concentration and temperature on thiocyanate wet oxidation was more noticeable in real effluents than in synthetic wastewaters containing only thiocyanate. It was also observed that the degree of mineralization of the matrix organic compounds was higher when the initial thiocyanate concentration increased. Taking into account the experimental data, kinetic models were obtained, and a mechanism implying free radicals was proposed for thiocyanate oxidation in the matrix considered. In all cases, sulphate, carbonates and ammonium were identified as the main reaction products of thiocyanate wet oxidation.

  10. The Impact of Block Scheduling on Student Achievement, Attendance, and Discipline at the High School Level

    ERIC Educational Resources Information Center

    Williams, Charles, Jr.

    2011-01-01

    The purpose of this study was to determine the impact block scheduling has on (a) student academic achievement, discipline, and attendance, and (b) administrator, teacher, and student perceptions. The study compared 2005-2010 data from a high school utilizing the A/B block schedule and a high school under a traditional schedule, in one suburban…

  11. The Role of Teachers at University: What Do High Achiever Students Look for?

    ERIC Educational Resources Information Center

    Monteiro, Silvia; Almeida, Leandro S.; Vasconcelos, Rosa M.

    2012-01-01

    The perceptions of students about their teachers have interested the academic and scientific community, regarding the improvement of the quality of higher education. This paper presents data obtained from interviews conducted with ten high achiever engineering students and focuses on the characteristics of teachers that are highly valued by the…

  12. Study-Orientation of High and Low Academic Achievers at Secondary Level in Pakistan

    ERIC Educational Resources Information Center

    Sarwar, Muhammad; Bashir, Muhammad; Khan, Muhammad Naemullah; Khan, Muhammad Saeed

    2009-01-01

    The study orientation of low and high academic achievers was compared, measured through a self-developed study orientation scale (SOS) primarily based on 47 items comparing study habits and attitude. Students' marks obtained in the 10th grade Examination determined the measure of academic performance. The analysis revealed that the high achievers…

  13. What Works Clearinghouse Quick Review: "Expanding College Opportunities for High-Achieving, Low Income Students"

    ERIC Educational Resources Information Center

    What Works Clearinghouse, 2013

    2013-01-01

    This study examined the effects of providing low-income, high-achieving high school seniors with college application guidance and information about the costs of college. The "application guidance" included information about deadlines and requirements for college applications at nearby institutions, at the state's flagship institution, and at in-…

  14. The Relationship between Self-Efficacy and Achievement in At-Risk High School Students

    ERIC Educational Resources Information Center

    Gold, Jarrett Graham

    2010-01-01

    The focus of this quantitative survey study was the examination of the relationship between self-efficacy and academic achievement in 164 at-risk high school students. The study used Bandura's self-efficacy as the theoretical framework. The research questions involved understanding the levels of self-efficacy in at-risk high school students and…

  15. The Contribution of Limbic Learning Aptitude to Achievement in High School. Final Report.

    ERIC Educational Resources Information Center

    Ax, Albert F.; And Others

    Achievement in earning grades in high school was resolved into its intellectual and motivational components. This study employed tests of I.Q., personality inventories and classical and operant conditioning of autonomic nervous system controlled variables. Eleven procedures were given to 99 Black inner city high school seniors. Six physiological…

  16. The Effects of Modeling Instruction on High School Physics Academic Achievement

    ERIC Educational Resources Information Center

    Wright, Tiffanie L.

    2012-01-01

    The purpose of this study was to explore whether Modeling Instruction, compared to traditional lecturing, is an effective instructional method to promote academic achievement in selected high school physics classes at a rural middle Tennessee high school. This study used an "ex post facto," quasi-experimental research methodology. The…

  17. Improving High School Students' Mathematics Achievement through the Use of Motivational Strategies.

    ERIC Educational Resources Information Center

    Portal, Jamie; Sampson, Lisa

    This report describes a program for motivating students in mathematics in order to improve achievement at the high school level. The targeted population consisted of high school students in a middle class community located in a suburb of a large metropolitan area. The problems of underachievement were documented through data collected from surveys…

  18. Coping with High-Achieving Transnationalist Immigrant Students: The Experience of Israeli Teachers

    ERIC Educational Resources Information Center

    Eisikovits, Rivka A.

    2008-01-01

    Little attention has been paid to teacher attitudes toward high-achieving culturally diverse student groups. This in-depth study focuses on the experience of Israeli teachers who tell the story of a decade and a half of educational work with their highly motivated, academically successful immigrant students from the Former Soviet Union. The paper…

  19. 10 Strategies for Raising Achievement and Improving High School Completion Rates

    ERIC Educational Resources Information Center

    Bottoms, Gene

    2004-01-01

    No state can afford to have the percentage of young people who are failing to finish high school remain at the present levels nor can they afford to ease the standards. This document discusses the following 10 strategies that states can implement to raise achievement and increase high school completion rates: (1) Initiate a transition program for…

  20. Emotional Intelligence as a Predictor of Leadership of Kuwaiti High and Low Achieving 11th Graders

    ERIC Educational Resources Information Center

    Alnabhan, Mousa

    2010-01-01

    The current study examined the association between emotional intelligence (EI) and the Leadership components (L) of high school students in the state of Kuwait. The possibility of predicting each leadership component via emotional intelligence components was investigated for high and low achievers. A sample of 11th grade students from Kuwaiti…

  1. Dual Enrollment Programs: A Comparative Study of High School Students' College Academic Achievement at Different Settings

    ERIC Educational Resources Information Center

    Flores, Agnes L. Acker

    2012-01-01

    The "ex post facto" causal-comparative study examined the academic achievement of high school students who took their dual credit English or mathematics college credit-bearing course in two different environments, namely, the college setting and the high school setting. Due to non-experimental nature of the study, no causal inferences…

  2. Classroom Environment, Instructional Resources, and Teaching Differences in High-Performing Kentucky Schools with Achievement Gaps.

    ERIC Educational Resources Information Center

    Meehan, Merrill L.; Cowley, Kimberly S.; Schumacher, Debbie; Hauser, Brenda; Croom, Nona D. M.

    This study examined differences at the classroom level between Kentucky schools with minimum versus large gaps in academic achievement between particular groups of students. Data were gathered via observations of 213 classrooms at 18 elementary, middle, and high schools. Although all the schools were identified as high-performing in terms of…

  3. A Case Study of 21st Century Skills in High Achieving Elementary Schools in Pennsylvania

    ERIC Educational Resources Information Center

    Egnor, Gregory P.

    2013-01-01

    This study examines if practices that advocate for 21st century skills are in conflict with the mandates of NCLB. Interviews with influential school leaders of high achieving elementary schools focused on collecting data about 21st century skills. This study was designed to (a) Determine if 21st century skills are addressed in high achieving…

  4. Small Classes in the Early Grades, Academic Achievement, and Graduating From High School

    ERIC Educational Resources Information Center

    Finn, Jeremy D.; Gerber, Susan B.; Boyd-Zaharias, Jayne

    2005-01-01

    This investigation addressed 3 questions about the long-term effects of early school experiences: (a) Is participation in small classes in the early grades (K-3) related to high school graduation? (b) Is academic achievement in K-3 related to high school graduation? (c) If class size is related to graduation, is the relationship explained by the…

  5. The Relationship between Thinking Style Differences and Career Choices for High-Achieving Students

    ERIC Educational Resources Information Center

    Kim, Mihyeon

    2011-01-01

    The intent of this study was to present information about high-achieving students' career decision making associated with thinking styles. We gathered data from two International Baccalaureate (IB) programs and a Governor's School Program with a sample of 209 high-school students. The findings of this study demonstrated that the effect of program…

  6. High-sensitivity in situ QCLAS-based ammonia concentration sensor for high-temperature applications

    NASA Astrophysics Data System (ADS)

    Peng, W. Y.; Sur, R.; Strand, C. L.; Spearrin, R. M.; Jeffries, J. B.; Hanson, R. K.

    2016-07-01

    A novel quantum cascade laser (QCL) absorption sensor is presented for high-sensitivity in situ measurements of ammonia (hbox {NH}_3) in high-temperature environments, using scanned wavelength modulation spectroscopy (WMS) with first-harmonic-normalized second-harmonic detection (scanned WMS-2 f/1 f) to neutralize the effect of non-absorption losses in the harsh environment. The sensor utilized the sQ(9,9) transition of the fundamental symmetric stretch band of hbox {NH}_3 at 10.39 {\\upmu }hbox {m} and was sinusoidally modulated at 10 kHz and scanned across the peak of the absorption feature at 50 Hz, leading to a detection bandwidth of 100 Hz. A novel technique was used to select an optimal WMS modulation depth parameter that reduced the sensor's sensitivity to spectral interference from hbox {H}_2hbox {O} and hbox {CO}_2 without significantly sacrificing signal-to-noise ratio. The sensor performance was validated by measuring known concentrations of hbox {NH}_3 in a flowing gas cell. The sensor was then demonstrated in a laboratory-scale methane-air burner seeded with hbox {NH}_3, achieving a demonstrated detection limit of 2.8 ± 0.26 ppm hbox {NH}_3 by mole at a path length of 179 cm, equivalence ratio of 0.6, pressure of 1 atm, and temperatures of up to 600 K.

  7. False Prolongation of Prothrombin Time in the Presence of a High Blood Concentration of Daptomycin.

    PubMed

    Yamada, Tomoyuki; Kato, Ryuji; Oda, Kazutaka; Tanaka, Hidema; Suzuki, Kaoru; Ijiri, Yoshio; Ikemoto, Toshiyuki; Nishihara, Masami; Hayashi, Tetsuya; Tanaka, Kazuhiko; Tamai, Hiroshi; Ukimura, Akira; Katsumata, Takahiro

    2016-10-01

    Prothrombin time (PT) can reportedly be falsely prolonged by the antimicrobial drug daptomycin (DAP), and concomitant use of phosphatidylglycerol (PG). Although high doses of DAP (>6 mg/kg/day) are recommended for severe infection and result in a high blood concentration, the extent to which high blood concentrations of DAP interfere with PT, in the presence or absence of PG, has yet to be determined when using the HemosIL RecombiPlasTin 2G (Werfen Japan, Tokyo, Japan). We examined the effects of high doses of DAP on PT using this reagent. DAP (0-500 mg/L) was added to normal plasma and plasma with an already prolonged PT in the presence or absence of liposomal amphotericin B (L-AMB, 5-50 mg/L) or COATSOME EL-01 empty cationic liposomes (CS, 25-250 mg/L). Furthermore, we undertook a Monte Carlo simulation to calculate the probability of achieving DAP concentrations >100, >200 and >500 mg/L 0-48 hr after administering 6-12 mg/kg of DAP. Apparent PT increased with increasing DAP concentration, but neither L-AMB nor CS appeared to further elevate PT when co-administered with DAP. The probability of achieving DAP concentrations >100 and >200 mg/L increased with DAP dose. Higher doses of DAP than the approved dose caused false prolongation of PT. PT should be monitored carefully in patients taking high doses of DAP; ideally, PT should be measured at the trough blood concentration of DAP. Concomitant use of L-AMB and CS did not generally further elevate PT when co-administered with DAP.

  8. Peripheral adaptation codes for high odor concentration in glomeruli.

    PubMed

    Lecoq, Jérôme; Tiret, Pascale; Charpak, Serge

    2009-03-11

    Adaptation is a general property of sensory receptor neurons and has been extensively studied in isolated cell preparation of olfactory receptor neurons. In contrast, little is known about the conditions under which peripheral adaptation occurs in the CNS during odorant stimulation. Here, we used two-photon laser-scanning microscopy and targeted extracellular recording in freely breathing anesthetized rats to investigate the correlate of peripheral adaptation at the first synapse of the olfactory pathway in olfactory bulb glomeruli. We find that during sustained stimulation at high concentration, odorants can evoke local field potential (LFP) postsynaptic responses that rapidly adapt with time, some within two inhalations. Simultaneous measurements of LFP and calcium influx at olfactory receptor neuron terminals reveal that postsynaptic adaptation is associated with a decrease in odorant-evoked calcium response, suggesting that it results from a decrease in glutamate release. This glomerular adaptation was concentration-dependent and did not change the glomerular input-output curve. In addition, in situ application of antagonists of either ionotropic glutamate receptors or metabotropic GABA(B) receptors did not affect this adaptation, thus discarding the involvement of local presynaptic inhibition. Glomerular adaptation, therefore, reflects the response decline of olfactory receptor neurons to sustained odorant. We postulate that peripheral fast adaptation is a means by which glomerular output codes for high concentration of odor.

  9. Electromagnetically assisted synthesis of highly concentrated gold nanoparticle colloids

    NASA Astrophysics Data System (ADS)

    Hernandez, Laura; Rosas, Walter; Naranjo, Guillermo; Peralta, Xomalin G.; Vargas, Watson L.

    2015-03-01

    The synthesis of metallic nanoparticles is currently an extremely active area of research due to the multiple potential applications of nanomaterials to areas ranging from nano-medicine to catalysis. Some of the current challenges of nanoparticle synthesis protocols include synthesizing nanoparticles in high concentrations with a small polydispersity. The present study contrasts and compares the synthesis of highly concentrated colloidal gold using three different sources of electromagnetic radiation to assist the reaction. The first source was a Spectra Physics Mai Tai Ti:Sapphire laser made by Sperian, this laser generates 70 fs FWHM pulses with wavelengths in the range of 690-1040 nm. The second source was sun light; this was measured to have a power of 10W. The third source was a lowelDP lamp with a measured intensity of 25W. Both the solar light and the lamp's rays were concentrated using a 28cm x 28cm Fresnel lens. Results will be presented highlighting differences and similarities in size, shape, crystallinity and time of the reaction. We speculate about the role played by variations in wavelength, temporal profile of the electromagnetic source (pulsed vs. continuous), temperature of the reaction and excitation power in the final structure of the nanoparticles generated.

  10. Material and Optical Design Rules for High Performance Luminescent Solar Concentrators

    NASA Astrophysics Data System (ADS)

    Bronstein, Noah Dylan

    This dissertation will highlight a path to achieve high photovoltaic conversion efficiency in luminescent solar concentrators, devices which absorb sunlight with a luminescent dye and then re-emit it into a waveguide where it is ultimately collected by a photovoltaic cell. Luminescent concentrators have been studied for more than three decades as potential low-cost but not high efficiency photovoltaics. Astute application of the blackbody radiation law indicates that photonic design is necessary to achieve high efficiency: a reflective filter must be used to trap luminescence at all angles while allowing higher energy photons to pass through. In addition, recent advances in the synthesis of colloidal nanomaterials have created the possibility for lumophores with broad absorption spectra, narrow-bandwidth emission, high luminescence quantum yield, tunable Stokes shifts and tunable Stokes ratios. Together, these factors allow luminescent solar concentrators to achieve the optical characteristics necessary for high efficiency. We have fabricated and tested the first generation of these devices. Our experiments demonstrate that the application of carefully matched photonic mirrors and luminescent quantum dots can allow luminescent concentration factors to reach record values while maintaining high photon collection efficiency. Finally, the photonic mirror dramatically mitigates the negative impact of scattering in the waveguide, allowing efficient photon collection over distances much longer than the scattering length of the waveguide. After demonstrating the possibility for high performance, we theoretically explore the efficacy of luminescent concentrators with dielectric reflectors as the high-bandgap top-junctions in two-junction devices. Simple thermodynamic calculations indicate that this approach can be nearly as good as a traditional vertically stacked tandem. The major barriers to such a device are the optical design of narrow-bandwidth, angle

  11. Strategies for the production of high concentrations of bioethanol from seaweeds: production of high concentrations of bioethanol from seaweeds.

    PubMed

    Yanagisawa, Mitsunori; Kawai, Shigeyuki; Murata, Kousaku

    2013-01-01

    Bioethanol has attracted attention as an alternative to petroleum-derived fuel. Seaweeds have been proposed as some of the most promising raw materials for bioethanol production because they have several advantages over lignocellulosic biomass. However, because seaweeds contain low contents of glucans, i.e., polysaccharides composed of glucose, the conversion of only the glucans from seaweed is not sufficient to produce high concentrations of ethanol. Therefore, it is also necessary to produce ethanol from other specific carbohydrate components of seaweeds, including sulfated polysaccharides, mannitol, alginate, agar and carrageenan. This review summarizes the current state of research on the production of ethanol from seaweed carbohydrates for which the conversion of carbohydrates to sugars is a key step and makes comparisons with the production of ethanol from lignocellulosic biomass. This review provides valuable information necessary for the production of high concentrations of ethanol from seaweeds.

  12. Symmetry-breaking phase transitions in highly concentrated semen

    PubMed Central

    Creppy, Adama; Plouraboué, Franck; Praud, Olivier; Druart, Xavier; Cazin, Sébastien; Yu, Hui

    2016-01-01

    New experimental evidence of self-motion of a confined active suspension is presented. Depositing fresh semen sample in an annular shaped microfluidic chip leads to a spontaneous vortex state of the fluid at sufficiently large sperm concentration. The rotation occurs unpredictably clockwise or counterclockwise and is robust and stable. Furthermore, for highly active and concentrated semen, richer dynamics can occur such as self-sustained or damped rotation oscillations. Experimental results obtained with systematic dilution provide a clear evidence of a phase transition towards collective motion associated with local alignment of spermatozoa akin to the Vicsek model. A macroscopic theory based on previously derived self-organized hydrodynamics models is adapted to this context and provides predictions consistent with the observed stationary motion. PMID:27733694

  13. Symmetry-breaking phase-transitions in highly concentrated semen

    NASA Astrophysics Data System (ADS)

    Plouraboué, Franck; Creppy, Adama; Praud, Olivier; Druart, Xavier; Cazin, Sébastien; Yu, Hui; Degond, Pierre

    2015-11-01

    New experimental evidence of self-motion of a confined active suspension is presented. Depositing fresh semen sample in an annular shaped micro-fluidic chip leads to a spontaneous rotation motion of the fluid at sufficiently large sperm concentration. The rotation occurs unpredictably clockwise or counterclockwise and is robust and stable. Furthermore, for highly active and concentrated semen, richer dynamics can occur such as self-sustained or damped rotation oscillations. Experimental results obtained with systematic dilution provide a clear evidence of a phase transition toward collective motion associated with local alignment of spermatozoa akin to the Vicsek model. A macroscopic theory based on previously derived Self-Organized Hydrodynamics (SOH) models is adapted to this context and provides predictions consistent with the observed stationary motion.

  14. Ignition characteristics of pulverized coal under high oxygen concentrations

    SciTech Connect

    Yue-sheng Fan; Zheng Zou; Zidong Cao; Yingchao Xu; Xiaoke Jiang

    2008-03-15

    In order to reduce overall fuel consumption, or partially substitute a 'valuable' fuel with a poor one, in electric power plant boilers, oxygen enrichment of combustion air can be very effective. Combustion characteristics of three Chinese pulverized coals, Shenmu bituminous, Tianhushan anthracite, and Duolun lignite, and three different particle sizes, under high oxygen concentrations more than 21%, have been investigated using thermogravimetric/differential scanning calorimetry analysis (TG/DSC) and a drop-tube furnace. Results showed that the ignitability, the combustion property, and the burnout were largely improved when added oxygen was used, especially for small particles, the influence of oxygen on the bituminous coal was greater than the lignite and the anthracite, and the suitable O{sub 2} concentration for the ignition of pulverized coal flow should be controlled below 40%. 38 refs., 12 figs., 3 tabs.

  15. Does Homogeneous Ability Grouping for High School Honors English Instruction Benefit the High Achiever?

    ERIC Educational Resources Information Center

    Hostetter, Douglas Paul

    2013-01-01

    Public schools are examining their policies and instructional practices to address the achievement gap exposed by the reporting requirements of NCLB (Wenglinski, 2004). As accountability measures and stakes rise, there is a call for an improved use of scientific evidence to inform educational policymaking (Wiseman, 2010). In terms of the…

  16. Design and Evaluation of the Highly Concentrated Human IgG Formulation Using Cyclodextrin Polypseudorotaxane Hydrogels.

    PubMed

    Higashi, Taishi; Tajima, Anna; Ohshita, Naoko; Hirotsu, Tatsunori; Abu Hashim, Irhan Ibrahim; Motoyama, Keiichi; Koyama, Sawako; Iibuchi, Ruriko; Mieda, Shiuhei; Handa, Kenji; Kimoto, Tomoaki; Arima, Hidetoshi

    2015-12-01

    To achieve the potent therapeutic effects of human immunoglobulin G (IgG), highly concentrated formulations are required. However, the stabilization for highly concentrated human IgG is laborious work. In the present study, to investigate the potentials of polypseudorotaxane (PPRX) hydrogels consisting of polyethylene glycol (PEG) and α- or γ-cyclodextrin (α- or γ-CyD) as pharmaceutical materials for highly concentrated human IgG, we designed the PPRX hydrogels including human IgG and evaluated their pharmaceutical properties. The α- and γ-CyDs formed PPRX hydrogels with PEG (M.W. 20,000) even in the presence of highly concentrated human IgG (>100 mg/mL). According to the results of (1)H-NMR, powder X-ray diffraction, and Raman microscopy, the formation of human IgG/CyD PPRX hydrogels was based on physical cross-linking arising from their columnar structures. The release profiles of human IgG from the hydrogels were in accordance with the non-Fickian diffusion model. Importantly, the stabilities of human IgG included into the hydrogels against thermal and shaking stresses were markedly improved. These findings suggest that PEG/CyD PPRX hydrogels are useful to prepare the formulation for highly concentrated human IgG.

  17. Academic achievement and career choice in science: Perceptions of African American urban high school students

    NASA Astrophysics Data System (ADS)

    Jones, Sheila Kay

    2007-12-01

    Low test scores in science and fewer career choices in science among African American high school students than their White counterparts has resulted in lower interest during high school and an underrepresentation of African Americans in science and engineering fields. Reasons for this underachievement are not known. This qualitative study used a grounded theory methodology to examine what influence parental involvement, ethnic identity, and early mentoring had on the academic achievement in science and career choice in science of African American urban high school 10th grade students. Using semi-structured open-ended questions in individual interviews and focus groups, twenty participants responded to questions about African American urban high school student achievement in science and their career choice in science. The median age of participants was 15 years; 85% had passed either high school biology or physical science. The findings of the study revealed influences and interactions of selected factors on African American urban high school achievement in science. Sensing potential emerged as the overarching theme with six subthemes; A Taste of Knowledge, Sounds I Hear, Aromatic Barriers, What Others See, The Touch of Others, and The Sixth Sense. These themes correlate to the natural senses of the human body. A disconnect between what science is, their own individual learning and success, and what their participation in science could mean for them and the future of the larger society. Insight into appropriate intervention strategies to improve African American urban high school achievement in science was gained.

  18. Patterns of Self-Regulation: Patterns of Self-Regulatory Strategy Use among Low-Achieving and High-Achieving University Students

    ERIC Educational Resources Information Center

    Ruban, Lilia; Reis, Sally M.

    2006-01-01

    The present mixed-methods study attempts to provide insights into the nature, idiosyncrasies, and inter- and intra-individual patterns of academic self-regulatory strategy use among two different populations of university students. Low-achieving (n = 49) and high-achieving students (n = 131) described their self-regulatory strategy use in their…

  19. Concentration Response Curve for Ozone Realted Mortality at High Concentrations for presentation at International Society for Environmental Epidemiology

    EPA Science Inventory

    Concentration Response Curve for Ozone related Mortality at High Concentrations Ana G. Rappold, James Crooks, Lucas M. Neas Background Rising temperatures and decreased global circulation in the upcoming decades are expected to have a detrimental impact on air quality, particular...

  20. High-accuracy measurements of N2O concentration and isotopic composition of low and high concentration samples with small volume injections using Cavity Ring-Down Spectroscopy

    NASA Astrophysics Data System (ADS)

    Saad, Nabil; Palmer, Melissa; Huang, Kuan

    2015-04-01

    Nitrous oxide (N2O) gas is among the major contributors to global warming and ozone depletion in stratosphere. Quantitative estimate of N2O production in various pathways and N2O fluxes across different reservoirs is the key to understanding the role of N2O in the global change. To achieve this goal, accurate and concurrent measurement of both N2O concentration ([N2O]) and its associated isotopic ratios (δ 15Nα , δ 15{N}β & δ 18O) is desired. Recent developments in Cavity Ring-Down Spectroscopy (CRDS) have enabled high-precision measurements of [N2O] and Site-Preference-δ 15N (SP-δ 15N) and δ 18O of a continuous gas flow. However, many N2O samples are discrete with limited volume ( 2 ppm), and are not suitable for direct continuous measurements by CRDS. Here we present results of a small sample introduction and handling device, labelled as Small Sample Isotope Module (SSIM), coupled to and automatically coordinated with a Picarro isotopic N2O CRDS analyzer to handle and measure high concentration and/or small volume samples. The SSIM requires 20 ml of sample volume per analysis at STP, and transfers the sample to the CRDS for high-precision concentration and isotope ratio measurements. When the injected sample is

  1. Particulate Matter Concentrations in East Oakland's High Street Corridor

    NASA Astrophysics Data System (ADS)

    Lei, P.; Jackson, J.; Lewis, R.; Marigny, A.; Mitchell, J. D.; Nguyen, R.; Philips, B.; Randle, D.; Romero, D.; Spears, D.; Telles, C.; Weissman, D.

    2012-12-01

    Particulate matter (PM) is a complex mixture of small solid pieces and/or liquid droplets in the air. High concentrations of PM can pose a serious health hazard because inhalation can result in breathing problems and/or aggravate asthma. Long term exposure can increase the likelihood of respiratory problems like asthma and emphysema as well as cancer. The smaller the particles, the deeper they can get into the respiratory system. For this reason, the smallest particles, those smaller than 2.5 micrometers in diameter (PM2.5), are the most dangerous. PM2.5 is largely emitted from motor vehicles burning fuels that don't break down fully. Our research team investigated the levels of PM2.5 as well as particles smaller than 10 micrometers (PM10) and total suspended particulate (TSP) along the northeast-southwest trending High Street Corridor, near Fremont High School in East Oakland, California. Using the Aerocet 531 mass particle counter, team members walked through neighborhoods and along major roads within a 1 mile radius of Fremont High School. The Aerocet 531 recorded two minute average measurements of all the relevant PM sizes, which are reported in mg/m3. Measurements were consistently taken in the morning, between 8:30 and 11:30 am. Preliminary results indicate maximum readings of all PM sizes at sites that are in close proximity to a major freeway (Interstate-880). These results support our initial hypothesis that proximity to major roads and freeways, especially those with high diesel-fuel burning truck traffic, would be the primary factor affecting PM concentration levels. Preliminary median and maximum readings all suggest particulate matter levels below what the EPA would consider unhealthy or risky.

  2. High performance concentration method for viruses in drinking water.

    PubMed

    Kunze, Andreas; Pei, Lu; Elsässer, Dennis; Niessner, Reinhard; Seidel, Michael

    2015-09-15

    According to the risk assessment of the WHO, highly infectious pathogenic viruses like rotaviruses should not be present in large-volume drinking water samples of up to 90 m(3). On the other hand, quantification methods for viruses are only operable in small volumes, and presently no concentration procedure for processing such large volumes has been reported. Therefore, the aim of this study was to demonstrate a procedure for processing viruses in-line of a drinking water pipeline by ultrafiltration (UF) and consecutive further concentration by monolithic filtration (MF) and centrifugal ultrafiltration (CeUF) of viruses to a final 1-mL sample. For testing this concept, the model virus bacteriophage MS2 was spiked continuously in UF instrumentation. Tap water was processed in volumes between 32.4 m(3) (22 h) and 97.7 m(3) (72 h) continuously either in dead-end (DE) or cross-flow (CF) mode. Best results were found by DE-UF over 22 h. The concentration of MS2 was increased from 4.2×10(4) GU/mL (genomic units per milliliter) to 3.2×10(10) GU/mL and from 71 PFU/mL to 2×10(8) PFU/mL as determined by qRT-PCR and plaque assay, respectively.

  3. Unexpectedly high ultrafine aerosol concentrations above East Antarctic sea ice

    NASA Astrophysics Data System (ADS)

    Humphries, R. S.; Klekociuk, A. R.; Schofield, R.; Keywood, M.; Ward, J.; Wilson, S. R.

    2016-02-01

    Better characterisation of aerosol processes in pristine, natural environments, such as Antarctica, have recently been shown to lead to the largest reduction in uncertainties in our understanding of radiative forcing. Our understanding of aerosols in the Antarctic region is currently based on measurements that are often limited to boundary layer air masses at spatially sparse coastal and continental research stations, with only a handful of studies in the vast sea-ice region. In this paper, the first observational study of sub-micron aerosols in the East Antarctic sea ice region is presented. Measurements were conducted aboard the icebreaker Aurora Australis in spring 2012 and found that boundary layer condensation nuclei (CN3) concentrations exhibited a five-fold increase moving across the polar front, with mean polar cell concentrations of 1130 cm-3 - higher than any observed elsewhere in the Antarctic and Southern Ocean region. The absence of evidence for aerosol growth suggested that nucleation was unlikely to be local. Air parcel trajectories indicated significant influence from the free troposphere above the Antarctic continent, implicating this as the likely nucleation region for surface aerosol, a similar conclusion to previous Antarctic aerosol studies. The highest aerosol concentrations were found to correlate with low-pressure systems, suggesting that the passage of cyclones provided an accelerated pathway, delivering air masses quickly from the free troposphere to the surface. After descent from the Antarctic free troposphere, trajectories suggest that sea-ice boundary layer air masses travelled equatorward into the low-albedo Southern Ocean region, transporting with them emissions and these aerosol nuclei which, after growth, may potentially impact on the region's radiative balance. The high aerosol concentrations and their transport pathways described here, could help reduce the discrepancy currently present between simulations and observations of

  4. 2×2 dominant achievement goal profiles in high-level swimmers.

    PubMed

    Fernandez-Rio, Javier; Cecchini Estrada, Jose A; Mendez-Giménez, Antonio; Fernández-Garcia, Benjamín; Saavedra, Pablo

    2014-01-01

    The goal of this study was to assess achievement goal dominance, self-determined situational motivation and competence in high-level swimmers before and after three training sessions set at different working intensities (medium, sub-maximal and maximal). Nineteen athletes (males, n=9, 18.00±2.32 years; females, n=10, 16.30±2.01 years, range = 14-18) agreed to participate. They completed a questionnaire that included the Dominant Achievement Goal assessment instrument, the 2×2 Achievement Goals Questionnaire for Sport (AGQ-S), The Situational Motivation Scale (SIMS) and the Competence subscale of the Basic Psychological Needs in Exercise questionnaire (BPNES). Results indicated that participants overwhelmingly showed mastery-approach achievement goal dominance, and it remained stable at the conclusion of the different training sessions under all intensity levels. This profile was positively correlated to self-determined situational motivation and competence. However, swimmers' feelings of competence increased only after the medium intensity level training session. After the completion of the maximal intensity training session, swimmers' self-determined motivation was significantly lower compared to the other two training sessions, which could be caused by a temporary period of burnout. Results indicated that high-level swimmers had a distinct mastery-approach dominant achievement goal profile that was not affected by the workload of the different training sessions. They also showed high levels of self-determined situational motivation and competence. However, heavy workloads should be controlled because they can cause transitory burnout.

  5. High manganese concentrations in rocks at Gale crater, Mars

    USGS Publications Warehouse

    Lanza, Nina L.; Fischer, Woodward W.; Wiens, Roger C.; Grotzinger, John; Ollila, Ann M.; Anderson, Ryan B.; Clark, Benton C.; Gellert, Ralf; Mangold, Nicolas; Maurice, Sylvestre; Le Mouélic, Stéphane; Nachon, Marion; Schmidt, Mariek E.; Berger, Jeffrey; Clegg, Samuel M.; Forni, Olivier; Hardgrove, Craig; Melikechi, Noureddine; Newsom, Horton E.; Sautter, Violaine

    2014-01-01

    The surface of Mars has long been considered a relatively oxidizing environment, an idea supported by the abundance of ferric iron phases observed there. However, compared to iron, manganese is sensitive only to high redox potential oxidants, and when concentrated in rocks, it provides a more specific redox indicator of aqueous environments. Observations from the ChemCam instrument on the Curiosity rover indicate abundances of manganese in and on some rock targets that are 1–2 orders of magnitude higher than previously observed on Mars, suggesting the presence of an as-yet unidentified manganese-rich phase. These results show that the Martian surface has at some point in time hosted much more highly oxidizing conditions than has previously been recognized.

  6. Shock initiation studies on high concentration hydrogen peroxide

    SciTech Connect

    Sheffield, Stephen A; Dattelbaum, Dana M; Stahl, David B; Gibson, L. Lee; Bartram, Brian D.

    2009-01-01

    Concentrated hydrogen peroxide (H{sub 2}O{sub 2}) has been known to detonate for many years. However, because of its reactivity and the difficulty in handling and confining it, along with the large critical diameter, few studies providing basic information about the initiation and detonation properties have been published. We are conducting a study to understand and quantify the initiation and detonation properties of highly concentrated H{sub 2}O{sub 2} using a gas-driven two-stage gun to produce well defined shock inputs. Multiple magnetic gauges are used to make in-situ measurements of the growth of reaction and subsequent detonation in the liquid. These experiments are designed to be one-dimensional to eliminate any difficulties that might be encountered with large critical diameters. Because of the concern of the reactivity of the H{sub 2}O{sub 2} with the confining materials, a remote loading system has been developed. The gun is pressurized, then the cell is filled and the experiment shot within less than three minutes. TV cameras are attached to the target so the cell filling can be monitored. Several experiments have been completed on {approx}98 wt % H{sub 2}O{sub 2}/H{sub 2}O mixtures; initiation has been observed in some experiments that shows homogeneous shock initiation behavior. The initial shock pressurizes and heats the mixture. After an induction time, a thermal explosion type reaction produces an evolving reactive wave that strengthens and eventually overdrives the first wave producing a detonation. From these measurements, we have determined unreacted Hugoniot information, times (distances) to detonation (Pop-plot points) that indicate low sensitivity, and detonation velocities of high concentration H{sub 2}O{sub 2}/H{sub 2}O solutions that agree with earlier estimates.

  7. High IQ Is Sufficient to Explain the High Achievements in Math and Science of the East Asian Peoples

    ERIC Educational Resources Information Center

    Lynn, Richard

    2010-01-01

    It is argued that it is unnecessary to propose that Confucian values explain the high achievements in math and science of the North East Asian peoples, and that these can be satisfactorily and more parsimoniously be explained by their high IQs.

  8. "It's a Way of Life for Us": High Mobility and High Achievement in Department of Defense Schools.

    ERIC Educational Resources Information Center

    Smrekar, Claire E.; Owens, Debra E.

    2003-01-01

    Examines the academic performance of students in U.S. Department of Defense Education Activity (DoDEA) schools, which have high student mobility. Some observers contend that these students' high achievement is a function of their middle class family and community characteristics. Asserts that DoDEA schools simultaneously "do the right…

  9. Room-temperature ferromagnetism in Cr-doped Si achieved by controlling atomic structure, Cr concentration, and carrier densities: A first-principles study

    SciTech Connect

    Wei, Xin-Yuan; Yang, Zhong-Qin; Zhu, Yan; Li, Yun

    2015-04-28

    By using first-principles calculations, we investigated how to achieve a strong ferromagnetism in Cr-doped Si by controlling the atomic structure and Cr concentration as well as carrier densities. We found that the configuration in which the Cr atom occupies the tetrahedral interstitial site can exist stably and the Cr atom has a large magnetic moment. Using this doping configuration, room-temperature ferromagnetism can be achieved in both n-type and p-type Si by tuning Cr concentration and carrier densities. The results indicate that the carrier density plays a crucial role in realizing strong ferromagnetism in diluted magnetic semiconductors.

  10. Effects of Part-Time Work on School Achievement During High School

    ERIC Educational Resources Information Center

    Singh, Kusum; Chang, Mido; Dika, Sandra

    2007-01-01

    The authors explored the effects of part-time work on school achievement during high school. To estimate the true effects of part-time work on school grades, the authors included family background, students' educational aspirations, and school engagement as controls. Although a substantial literature exists on the relationship of part-time work…

  11. The Federal Transformation Intervention Model in Persistently Lowest Achieving High Schools: A Mixed-Methods Study

    ERIC Educational Resources Information Center

    Le Patner, Michelle B.

    2012-01-01

    This study examined the American Recovery and Reinvestment Act federal mandate of the Transformation Intervention Model (TIM) outlined by the School Improvement Grant, which was designed to turn around persistently lowest achieving schools. The study was conducted in four high schools in a large Southern California urban district that selected the…

  12. Balancing Dreams and Realities: The College Choice Process for High-Achieving Latinas

    ERIC Educational Resources Information Center

    Hernández, Ebelia

    2015-01-01

    This study's narratives of 17 high-achieving Latinas revealed how their college choice was a constant balancing of individual and family expectations, being "close, but far enough away," and "getting your money's worth." With the use of critical race theory, further analysis revealed the influence of "familismo" on…

  13. Fostering the Promise of High Achieving Mathematics Students through Curriculum Differentiation

    ERIC Educational Resources Information Center

    Zmood, Simone

    2014-01-01

    Recent research suggests some teachers may not have a wide range of teaching and learning strategies for their most proficient mathematics students, which could impact on these students' learning and ongoing improvement in performance. This paper outlines the different drivers of high achievement and explores the main curriculum differentiation…

  14. Being Labeled "Nerd": Factors that Influence the Social Acceptance of High-Achieving Students

    ERIC Educational Resources Information Center

    Rentzsch, Katrin; Schutz, Astrid; Schroder-Abe, Michela

    2011-01-01

    The present investigation addresses the question of whether certain factors can protect high-achieving students at risk for being labeled a nerd against devaluation. In 2 studies, 125 and 317 students from Grade 8 evaluated vignettes describing average students and students who were called "nerds." Results indicate that being modest…

  15. Conflicts and Communication between High-Achieving Chinese American Adolescents and Their Parents

    ERIC Educational Resources Information Center

    Qin, Desiree Baolian; Chang, Tzu-Fen; Han, Eun-Jin; Chee, Grace

    2012-01-01

    Drawing on in-depth interview data collected on 18 high-achieving Chinese American students, the authors examine domains of acculturation-based conflicts, parent and child internal conflicts, and conflict resolution in their families. Their analyses show that well-established negative communication patterns in educational expectations, divergent…

  16. The College-Choice Process of High Achieving Freshmen: A Comparative Case Study

    ERIC Educational Resources Information Center

    Dale, Amanda

    2010-01-01

    The purpose of this study was to examine the college-choice process of high achieving students. Employing current literature and previous research, it combined current models of college choice and the influential factors identified throughout the literature while utilizing the concept of bounded rationality to create a conceptual framework to…

  17. Examining the Relationship between Selected Variables and the Academic Achievement of African American High School Students

    ERIC Educational Resources Information Center

    Graham, David Mark

    2009-01-01

    Research investigating the impact of factors such as gender, socioeconomic status, racial socialization, and academic self-concept on the academic achievement of African American high school students has been of interest to scholars for decades. Previous literature has focused much attention on the relationship of each of these constructs and…

  18. The Transition Experiences of High-Achieving, Low-Income Undergraduates in an Elite College Environment

    ERIC Educational Resources Information Center

    McLoughlin, Paul J., II

    2012-01-01

    This hermeneutic phenomenological study describes the lived experiences of high-achieving, low-income undergraduates and their transition into a college environment historically reserved for wealthy students. The results of this study indicate that these students are flourishing in full need-based financial aid programs as a result of their own…

  19. Examining the Predictive Power of Autonomy and Self-Evaluation on High School Students' Language Achievement

    ERIC Educational Resources Information Center

    Yuksel, Ismail; Toker, Yalcin

    2013-01-01

    This study aims to determine language learners' autonomy, self-evaluation levels and to examine the predictive power of these two variables on language achievement. The study was designed as mixed method design and was conducted with 108 high school students. Data were collected through an autonomy scale, a self-evaluation scale, schools record on…

  20. Mathematics Attitudes and Achievement of U.S. High School Sophomores Based on Race

    ERIC Educational Resources Information Center

    Martinez, James

    2017-01-01

    What are high school students thinking? The purpose of this study was to examine the degree that psychosocial attitudes affect academic achievement in mathematics for students of different races during secondary schooling. Based on a quantitative methodology, data was gathered from a nationally distributed survey involving over 16,000 student…

  1. The Effects of Alcohol Use on Academic Achievement in High School

    ERIC Educational Resources Information Center

    Balsa, Ana I.; Giuliano, Laura M.; French, Michael T.

    2011-01-01

    This paper examines the effects of alcohol use on high school students' quality of learning. We estimate fixed-effects models using data from the National Longitudinal Study of Adolescent Health. Our primary measure of academic achievement is the student's grade point average (GPA) abstracted from official school transcripts. We find that…

  2. Growing into Equity: Professional Learning and Personalization in High-Achieving Schools

    ERIC Educational Resources Information Center

    Gleason, Sonia Caus; Gerzon, Nancy

    2013-01-01

    What makes a Title I school high-achieving, and what can we all learn from that experience? Professional learning and leadership that supports personalized instruction makes the difference, as captured in the ground-breaking research of authors Sonia Caus Gleason and Nancy Gerzon. This illuminating book shows how four outstanding schools are…

  3. Further Evidence of an Engagement-Achievement Paradox among U.S. High School Students

    ERIC Educational Resources Information Center

    Shernoff, David J.; Schmidt, Jennifer A.

    2008-01-01

    Achievement, engagement, and students' quality of experience were compared by racial and ethnic group in a sample of students (N = 586) drawn from 13 high schools with diverse ethnic and socioeconomic student populations. Using the Experience Sampling Method (ESM), 3,529 samples of classroom experiences were analyzed along with self-reported…

  4. Impact of Physical Environment on Academic Achievement of High School Youth.

    ERIC Educational Resources Information Center

    Burkhalter, Bettye B.

    1983-01-01

    To study the relationship of the physical environment to high school students' academic achievement, 60 students participated in an experiential career exploration program at the Alabama Space and Rocket Center while 108 students participated in a traditional careers program. Tests indicated the former group improved more in career choice…

  5. Reliability and Validity Evidence for Achievement Goal Models in High School Physical Education Settings

    ERIC Educational Resources Information Center

    Guan, Jianmin; McBride, Ron; Xiang, Ping

    2007-01-01

    Although empirical research in academic areas provides support for both a 3-factor as well as a 4-factor achievement goal model, both models were proposed and tested with a collegiate sample. Little is known about the generalizability of either model with high school level samples. This study was designed to examine whether the 3-factor model…

  6. Antecedent and Concurrent Psychosocial Skills That Support High Levels of Achievement within Talent Domains

    ERIC Educational Resources Information Center

    Olszewski-Kubilius, Paula; Subotnik, Rena F.; Worrell, Frank C.

    2015-01-01

    Motivation and emotional regulation are important for the sustained focused study and practice required for high levels of achievement and creative productivity in adulthood. Using the talent development model proposed by the authors as a framework, the authors discuss several important psychosocial skills based on the psychological research…

  7. How High-Achieving African American Undergraduate Men Negotiate Cultural Challenges at a Predominantly White Institution

    ERIC Educational Resources Information Center

    Bradley, Elva Elaine

    2010-01-01

    In this study I examine the manner in which high-achieving African American undergraduate men negotiate cultural challenges in a predominantly White institution (PWI). Cultural theory underpins the conceptual framework of this case study. Basing the study in cultural theory provided a lens through which to view the lived experiences of the twenty…

  8. Central American Refugees and U.S. High Schools. A Psychosocial Study of Motivation and Achievement.

    ERIC Educational Resources Information Center

    Suarez-Orozco, Marcelo M.

    This ethnographic study documents and interprets key school, work, and family life issues in the lives and experiences of a sampling of recent immigrants from the war-torn Central American nations; and suggests a psychocultural theory of achievement motivation. Information was gathered from observation in two urban high schools, interviews with 50…

  9. The Impact of Inclusion on the Academic Achievement of High School Special Education Students

    ERIC Educational Resources Information Center

    Dawkins, Harold Smith

    2010-01-01

    This dissertation examined the impact of inclusion on the academic achievement outcome of high school special education students as measured by English 1, biology, and algebra 1 as a function of gender, ethnicity, and years of inclusion. The study also examined the generalizations with confidence that could be made about the use of inclusion…

  10. Experiencing More Mathematics Anxiety than Expected? Contrasting Trait and State Anxiety in High Achieving Students

    ERIC Educational Resources Information Center

    Roos, A.-L.; Bieg, M.; Goetz, T.; Frenzel, A. C.; Taxer, J.; Zeidner, M.

    2015-01-01

    This study examined mathematics anxiety among high and low achieving students (N = 237, grades 9 and 10) by contrasting trait (habitual) and state (momentary) assessments of anxiety. Previous studies have found that trait anxiety measures are typically rated higher than state measures. Furthermore, the academic self-concept has been identified to…

  11. High-Stakes Testing and Student Achievement: Updated Analyses with NAEP Data

    ERIC Educational Resources Information Center

    Nichols, Sharon L.; Glass, Gene V.; Berliner, David C.

    2012-01-01

    The present research is a follow-up study of earlier published analyses that looked at the relationship between high-stakes testing pressure and student achievement in 25 states. Using the previously derived Accountability Pressure Index (APR) as a measure of state-level policy pressure for performance on standardized tests, a series of…

  12. Standardized Tests as Measurements of Achievement: Does the High School Assessment Program (HSAP) Measure Up?

    ERIC Educational Resources Information Center

    Ray, Susan Amanda

    2008-01-01

    Purpose: The purpose of this study was to determine the correlation between HSAP scores and various measures of classroom achievement such as overall GPA, End Of Course Scores and SAT/ACT scores of Berea High School [BHS] students in the classes of 2005-2006 and 2006-2007. Methodology: The researcher collected the following data for random samples…

  13. Brain Structure and Resting-State Functional Connectivity in University Professors with High Academic Achievement

    ERIC Educational Resources Information Center

    Li, Weiwei; Yang, Wenjing; Li, Wenfu; Li, Yadan; Wei, Dongtao; Li, Huimin; Qiu, Jiang; Zhang, Qinglin

    2015-01-01

    Creative persons play an important role in technical innovation and social progress. There is little research on the neural correlates with researchers with high academic achievement. We used a combined structural (regional gray matter volume, rGMV) and functional (resting-state functional connectivity analysis, rsFC) approach to examine the…

  14. Ugandan Immigrant Students' Perceptions of Barriers to Academic Achievement in American High Schools

    ERIC Educational Resources Information Center

    Ssekannyo, Denis

    2010-01-01

    In a world that is now a global village, enterprising individuals, especially from Third World countries, who make it to greener pastures do not leave their children behind. But with a long list of barriers to academic achievement associated with immigrant and minority students in American high schools, an understanding of the experiences and…

  15. Students' High School Organizational Leadership Opportunities and Their Influences on Academic Achievement and Civic Participation

    ERIC Educational Resources Information Center

    Elemen, Jennifer E.

    2015-01-01

    The purpose of this quantitative study was to analyze high school leadership praxis for its inclusion of students in organizational leadership dialogue and decision-making and the influences of these factors on student achievement and civic participation. Survey questionnaire data were provided by 215 full-time enrolled undergraduate students from…

  16. Achievement, School Integration, and Self-Efficacy in Single-Sex and Coeducational Parochial High Schools

    ERIC Educational Resources Information Center

    Micucci, Kara Hanson

    2014-01-01

    A structural model for prior achievement, school integration, and self-efficacy was developed using Tinto's theory of student attrition and Bandura's self-efficacy theory. The model was tested and revised using a sample of 1,452 males and females from single-sex and coeducational parochial high schools. Results indicated that the theoretically…

  17. The Relationship between Illinois School District Superintendent Longevity and High School Student Achievement

    ERIC Educational Resources Information Center

    Libka, Robert J.

    2012-01-01

    Frequent changes in school district superintendents may be having a detrimental impact on student achievement. Rapid changes in leadership today parallel the present (NCLB) era of high stakes state assessments. The goal of the study was to provide correlation research that would have a positive effect on school district management, superintendent…

  18. Effect of Textbook Readability on Student Achievement in High School Chemistry.

    ERIC Educational Resources Information Center

    Rapp, D. Neil

    2001-01-01

    Notes the readability level of many high school chemistry textbooks is far above students' reading levels. Conducts two separate studies, making every effort to keep the two classes as similar as possible in all aspects except text. Finds strong evidence that changing the chemistry textbook resulted in an increase in student achievement. Suggests…

  19. Negative Relationship between Achievement in High School and Self-Concept in College.

    ERIC Educational Resources Information Center

    Wolfe, Raymond N.; Grosch, James W.

    Social learning theory implies that there should be a significant positive relationship between academic performance and self-concept and outcomes of recent meta-analyses support this prediction. While path-analytic studies of high school samples in the 1960s and 1970s demonstrated that ability and achievement each made a small positive…

  20. The Impact of Reading Success Academy on High School Reading Achievement

    ERIC Educational Resources Information Center

    Burlison, Kelly; Chave, Josh

    2014-01-01

    The study explores the effectiveness of the Reading Success Academy on the reading achievement of the selected group of ninth-grade students in a comprehensive high school. We examine in what ways the Reading Success Academy may improve the reading proficiency rates and amount of reading growth of ninth-grade students. The results indicate that…

  1. Black High Achieving Undergraduate Mathematics Majors Discuss Success and Persistence in Mathematics

    ERIC Educational Resources Information Center

    Ellington, Roni M.; Frederick, Rona

    2010-01-01

    Experiences of eight Black high-achieving college junior and senior mathematics majors are examined to discern which social and cultural factors shape success and persistence in mathematics. College persistence literature as well as mathematics education studies that document Black students' success in mathematics were used as frameworks to…

  2. Teaching Practices in Grade 5 Mathematics Classrooms with High-Achieving English Learner Students

    ERIC Educational Resources Information Center

    Merritt, Eileen G.; Palacios, Natalia; Banse, Holland; Rimm-Kaufman, Sara E.; Leis, Micela

    2017-01-01

    Teachers need more clarity about effective teaching practices as they strive to help their low-achieving students understand mathematics. Our study describes the instructional practices used by two teachers who, by value-added metrics, would be considered "highly effective teachers" in classrooms with a majority of students who were…

  3. One-to-One Computing and Student Achievement in Ohio High Schools

    ERIC Educational Resources Information Center

    Williams, Nancy L.; Larwin, Karen H.

    2016-01-01

    This study explores the impact of one-to-one computing on student achievement in Ohio high schools as measured by performance on the Ohio Graduation Test (OGT). The sample included 24 treatment schools that were individually paired with a similar control school. An interrupted time series methodology was deployed to examine OGT data over a period…

  4. Emotional Intelligence and Academic Achievement of High School Students in Kanyakumari District

    ERIC Educational Resources Information Center

    Lawrence, A. S. Arul; Deepa, T.

    2013-01-01

    The objective of the study is to find the significant relationship between emotional intelligence and academic achievement of high school students with reference to the background variables. Survey method was employed. Two tools are used in this study namely self-made Trait Emotional Intelligence Questionnaire Short Form (TEIQue SF) and the…

  5. Integrating Economic and Social Policy: Good Practices from High-Achieving Countries. Innocenti Working Papers.

    ERIC Educational Resources Information Center

    Mehrotra, Santosh

    This paper examines the successes of 10 "high achievers," countries with social indicators far higher than might be expected, given their national wealth, pulling together the lessons learned for social policy in the developing world. The 10 countries identified are Costa Rica, Cuba, Barbados, Botswana, Zimbabwe, Mauritius, Kerala, Sri…

  6. Spatial Experiences of High Academic Achievers: Insights from a Developmental Perspective

    ERIC Educational Resources Information Center

    Weckbacher, Lisa Marie; Okamoto, Yukari

    2012-01-01

    The study explored the relationship between types of spatial experiences and spatial abilities among 13- to 14-year-old high academic achievers. Each participant completed two spatial tasks and a survey assessing favored spatial activities across five categories (computers, toys, sports, music, and art) and three developmental periods (early…

  7. The Impact of High School Size on Math Achievement and Dropout Rate

    ERIC Educational Resources Information Center

    Werblow, Jacob; Duesbery, Luke

    2009-01-01

    The study explores the ways in which school size influences two important student outcomes commonly used in school effects research: growth in mathematics achievement and dropout rate. Past research suggests that smaller high schools can lead to increased benefits for students. In this study, multilevel analytic models of the first two waves of…

  8. Filial Piety and Academic Motivation: High-Achieving Students in an International School in South Korea

    ERIC Educational Resources Information Center

    Tam, Jonathan

    2016-01-01

    This study uses self-determination theory to explore the mechanisms of filial piety in the academic motivation of eight high-achieving secondary school seniors at an international school in South Korea, resulting in several findings. First, the students attributed their parents' values and expectations as a major source of the students'…

  9. Obesity, High-Calorie Food Intake, and Academic Achievement Trends among U.S. School Children

    ERIC Educational Resources Information Center

    Li, Jian; O'Connell, Ann A.

    2012-01-01

    The authors investigated children's self-reported high-calorie food intake in Grade 5 and its relationship to trends in obesity status and academic achievement over the first 6 years of school. They used 3-level hierarchical linear models in the large-scale database (the Early Childhood Longitudinal Study--Kindergarten Cohort). Findings indicated…

  10. Teachers and Student Achievement in the Chicago Public High Schools. WP 2002-28. Revised

    ERIC Educational Resources Information Center

    Aaronson, Daniel; Barrow, Lisa; Sander, William

    2003-01-01

    Using unique administrative data on Chicago public high school students and their teachers, we are able to estimate the importance of teachers on student mathematical achievement. We find that teachers are educationally and statistically important. To be sure, sampling variation and other measurement issues can strongly influence estimates of…

  11. Social Media Use, Loneliness, and Academic Achievement: A Correlational Study with Urban High School Students

    ERIC Educational Resources Information Center

    Neto, Roque; Golz, Nancy; Polega, Meaghan

    2015-01-01

    This study explored the association between social media use, loneliness, and academic achievement in high school students and identified the demographic characteristics associated with these three elements. This study also aimed to identify the percentage of variance in loneliness accounted for by social media use and GPA. Participants were 345…

  12. Actively Closing the Gap? Social Class, Organized Activities, and Academic Achievement in High School

    ERIC Educational Resources Information Center

    Morris, David S.

    2015-01-01

    Participation in Organized Activities (OA) is associated with positive behavioral and developmental outcomes in children. However, less is known about how particular aspects of participation affect the academic achievement of high school students from different social class positions. Using the Education Longitudinal Study of 2002, this study…

  13. Turkish High School Students' Biology Achievement in Relation to Academic Self-Regulation

    ERIC Educational Resources Information Center

    Yumusak, Necmettin; Sungur, Semra; Cakiroglu, Jale

    2007-01-01

    This study aimed at investigating the contribution of motivational beliefs, cognitive, and metacognitive strategy use to Turkish high school students' achievement in biology. In order to investigate the specified purpose of the study, 519 tenth-grade students were administered the Motivated Strategies for Learning Questionnaire (Pintrich, Smith,…

  14. Communication Satisfaction, Organizational Citizenship Behavior and the Relationship to Student Achievement in High Schools

    ERIC Educational Resources Information Center

    Blanchard, Gayle A.

    2012-01-01

    This study used a correlational design that allowed the researcher to examine the relationship among communication satisfaction, organizational citizenship behaviors (OCB) and student achievement. High school teachers were surveyed from a convenience sample of 12 school districts in Arizona. Established instruments were used to survey teachers'…

  15. Consequences of the Confucian Culture: High Achievement but Negative Psychological Attributes?

    ERIC Educational Resources Information Center

    Ho, Irene T.; Hau, Kit-Tai

    2010-01-01

    In "Unforgiving Confucian culture: A breeding ground for high academic achievement, test anxiety and self-doubt?" Stankov (in press) provides three reasons for caution against over-glorifying the academic excellence of Confucian Asian learners, namely that it may lead to a reluctance to change their rote learning approach which is not conducive to…

  16. Evaluative and Behavioral Correlates to Intrarehearsal Achievement in High School Bands

    ERIC Educational Resources Information Center

    Montemayor, Mark

    2014-01-01

    The purpose of this study was to investigate relationships of teaching effectiveness, ensemble performance quality, and selected rehearsal procedures to various measures of intrarehearsal achievement (i.e., musical improvement exhibited by an ensemble during the course of a single rehearsal). Twenty-nine high school bands were observed in two…

  17. Faculty Perceptions of High-Achieving Male Collegians: A Critical Race Theory Analysis

    ERIC Educational Resources Information Center

    Comeaux, Eddie

    2013-01-01

    Critical race theory was employed as an interpretive framework to explore faculty perceptions of the academic accomplishments of high-achieving Black and White male collegians. Using photo elicitation methodology, faculty participants responded to a randomly assigned photograph of and vignette about either a Black or White male student. While most…

  18. Self-Graded and Teacher-Graded Achievement in a BSCS High School Biology Course.

    ERIC Educational Resources Information Center

    Good, Wallace Martin

    The effect of self-grading on biology students exposed to the same instruction (except grading) in an upper-middle class public school was investigated by comparing self-graded and teacher-graded populations in (1) achievement in high school biology, (2) level of aspiration behavior, (3) critical thinking skills, and (4) productivity. The…

  19. Cognitive Abilities and Motivational Processes in High School Students' Situational Engagement and Achievement in Science.

    ERIC Educational Resources Information Center

    Lau, Shun; Roeser, Robert W.

    2002-01-01

    Building on R. Snow's two pathways to achievement outcomes (1989), examined how cognitive and motivational factors associated with the performance and commitment pathways respectively contributed to prediction of outcomes in science for 491 high school students. Results are consistent with Snow's conjecture that factors related to both pathways…

  20. Overall Findings: Common Practices and Procedures across Schools. High Achieving Schools Study. Synthesis Report

    ERIC Educational Resources Information Center

    Mohajeri-Nelson, Nazanin; Bamberry, Lynn; Dunaway, Wendy; Hunter, Ellen; Klein, Jeff; Kuntz, Courtney; Negley, Tina; Singer, Robin; Ottenbreit, Rebekah; Young, Eric

    2015-01-01

    This report summarizes the factors that were commonly noted across five high achieving elementary schools in Colorado: (1) Burlington; (2) Canyon Creek; (3) Soaring Eagles; (4) South Lakewood; and (5) Tavelli. After 10 days of onsite visits to participating schools, noteworthy commonalities surfaced across the schools. Policies, practices, and…

  1. Design and development of a high-concentration and high-efficiency photovoltaic concentrator using a curved Fresnel lens

    SciTech Connect

    Scharlack, R.S.; Moffat, A.

    1983-08-01

    Thermo Electron has designed a high concentration photovoltaic module that uses a domed, point-focus Fresnel lens. Their design, design optimization process, and results from lens and receiver tests are described in this report. A complete module has not been fabricated and probably will not be fabricated in the future; however, Thermo Electron's optical design, analysis, and testing of both secondary optical units and domed Fresnel lenses have made a significant contribution to our project. Tooling errors prevented the lens from reaching its potential efficiency by the end of the contract, and resolution of these tooling problems is currently being attempted with a follow-on contract, No. 68-9463.

  2. A high-performance photovoltaic concentrator array - The mini-dome Fresnel lens concentrator with 30 percent efficient GaAs/GaSb tandem cells

    NASA Technical Reports Server (NTRS)

    Piszczor, M. F.; Brinker, D. J.; Flood, D. J.; Avery, J. E.; Fraas, L. M.; Fairbanks, E. S.; Yerkes, J. W.; O'Neill, M. J.

    1991-01-01

    A high-efficiency, lightweight space photovoltaic concentrator array is described. Previous work on the minidome Fresnel lens concentrator concept is being integrated with Boeing's 30 percent efficient tandem GaAs/GaSb concentrator cells into a high-performance photovoltaic array. Calculations indicate that, in the near term, such an array can achieve 300 W/sq m at a specific power of 100 W/kg. Emphasis of the program has now shifted to integrating the concentrator lens, tandem cell, and supporting panel structure into a space-qualifiable array. A description is presented of the current status of component and prototype panel testing and the development of a flight panel for the Photovoltaic Array Space Power Plus Diagnostics (PASP PLUS) flight experiment.

  3. A high-performance photovoltaic concentrator array - The mini-dome Fresnel lens concentrator with 30 percent efficient GaAs/GaSb tandem cells

    NASA Astrophysics Data System (ADS)

    Piszczor, M. F.; Brinker, D. J.; Flood, D. J.; Avery, J. E.; Fraas, L. M.; Fairbanks, E. S.; Yerkes, J. W.; O'Neill, M. J.

    A high-efficiency, lightweight space photovoltaic concentrator array is described. Previous work on the minidome Fresnel lens concentrator concept is being integrated with Boeing's 30 percent efficient tandem GaAs/GaSb concentrator cells into a high-performance photovoltaic array. Calculations indicate that, in the near term, such an array can achieve 300 W/sq m at a specific power of 100 W/kg. Emphasis of the program has now shifted to integrating the concentrator lens, tandem cell, and supporting panel structure into a space-qualifiable array. A description is presented of the current status of component and prototype panel testing and the development of a flight panel for the Photovoltaic Array Space Power Plus Diagnostics (PASP PLUS) flight experiment.

  4. Effect of temperature on Chinese rice wine brewing with high concentration presteamed whole sticky rice.

    PubMed

    Liu, Dengfeng; Zhang, Hong-Tao; Xiong, Weili; Hu, Jianhua; Xu, Baoguo; Lin, Chi-Chung; Xu, Ling; Jiang, Lihua

    2014-01-01

    Production of high quality Chinese rice wine largely depends on fermentation temperature. However, there is no report on the ethanol, sugars, and acids kinetics in the fermentation mash of Chinese rice wine treated at various temperatures. The effects of fermentation temperatures on Chinese rice wine quality were investigated. The compositions and concentrations of ethanol, sugars, glycerol, and organic acids in the mash of Chinese rice wine samples were determined by HPLC method. The highest ethanol concentration and the highest glycerol concentration both were attained at the fermentation mash treated at 23 °C. The highest peak value of maltose (90 g/L) was obtained at 18 °C. Lactic acid and acetic acid both achieved maximum values at 33 °C. The experimental results indicated that temperature contributed significantly to the ethanol production, acid flavor contents, and sugar contents in the fermentation broth of the Chinese rice wines.

  5. Three-stage enzymatic hydrolysis of steam-exploded corn stover at high substrate concentration.

    PubMed

    Yang, Jing; Zhang, Xiaoping; Yong, Qiang; Yu, Shiyuan

    2011-04-01

    The feasibility of three-stage hydrolysis of steam-exploded corn stover at high-substrate concentration was investigated. When substrate concentration was 30% and enzyme loading was 15-30 FPU/g cellulose, three-stage (9+9+12 h) hydrolysis could reach a hydrolysis yield of 59.9-81.4% in 30 h. Compared with one-stage hydrolysis for 72 h, an increase of 34-37% in hydrolysis yield could be achieved. When steam-exploded corn stover was used as the substrate for enzyme synthesis and hydrolysis was conducted at a substrate concentration of 25% with an enzyme loading of 20 FPU/g cellulose, a hydrolysis yield of 85.1% was obtained, 19% higher than that the commercial cellulase could reach under the same conditions. The removal of end products was suggested to improve the adsorption of cellulase on the substrate and enhance the productivity of enzymatic hydrolysis.

  6. Effect of Temperature on Chinese Rice Wine Brewing with High Concentration Presteamed Whole Sticky Rice

    PubMed Central

    Zhang, Hong-Tao; Xiong, Weili; Hu, Jianhua; Xu, Baoguo; Lin, Chi-Chung; Xu, Ling; Jiang, Lihua

    2014-01-01

    Production of high quality Chinese rice wine largely depends on fermentation temperature. However, there is no report on the ethanol, sugars, and acids kinetics in the fermentation mash of Chinese rice wine treated at various temperatures. The effects of fermentation temperatures on Chinese rice wine quality were investigated. The compositions and concentrations of ethanol, sugars, glycerol, and organic acids in the mash of Chinese rice wine samples were determined by HPLC method. The highest ethanol concentration and the highest glycerol concentration both were attained at the fermentation mash treated at 23°C. The highest peak value of maltose (90 g/L) was obtained at 18°C. Lactic acid and acetic acid both achieved maximum values at 33°C. The experimental results indicated that temperature contributed significantly to the ethanol production, acid flavor contents, and sugar contents in the fermentation broth of the Chinese rice wines. PMID:24672788

  7. Liquefaction of lignocellulose at high-solids concentrations.

    PubMed

    Jørgensen, Henning; Vibe-Pedersen, Jakob; Larsen, Jan; Felby, Claus

    2007-04-01

    To improve process economics of the lignocellulose to ethanol process a reactor system for enzymatic liquefaction and saccharification at high-solids concentrations was developed. The technology is based on free fall mixing employing a horizontally placed drum with a horizontal rotating shaft mounted with paddlers for mixing. Enzymatic liquefaction and saccharification of pretreated wheat straw was tested with up to 40% (w/w) initial DM. In less than 10 h, the structure of the material was changed from intact straw particles (length 1-5 cm) into a paste/liquid that could be pumped. Tests revealed no significant effect of mixing speed in the range 3.3-11.5 rpm on the glucose conversion after 24 h and ethanol yield after subsequent fermentation for 48 h. Low-power inputs for mixing are therefore possible. Liquefaction and saccharification for 96 h using an enzyme loading of 7 FPU/g.DM and 40% DM resulted in a glucose concentration of 86 g/kg. Experiments conducted at 2%-40% (w/w) initial DM revealed that cellulose and hemicellulose conversion decreased almost linearly with increasing DM. Performing the experiments as simultaneous saccharification and fermentation also revealed a decrease in ethanol yield at increasing initial DM. Saccharomyces cerevisiae was capable of fermenting hydrolysates up to 40% DM. The highest ethanol concentration, 48 g/kg, was obtained using 35% (w/w) DM. Liquefaction of biomass with this reactor system unlocks the possibility of 10% (w/w) ethanol in the fermentation broth in future lignocellulose to ethanol plants.

  8. High Expectations--High Achievement on Literacy: "What Shall We Do in This Hangman's Hour?"

    ERIC Educational Resources Information Center

    Linnakyla, Pirjo

    Finland is a country of great expectations on literacy and literacy education. High expectations and demands have, however, a darker side. High expectations of society, parents, and teachers may have an effect on the students' self-esteem. The economic recession in the early 1990s strongly accelerated the change in literacy demands and…

  9. Cultivating a Growth Mindset in Students at a High-Achieving High School

    ERIC Educational Resources Information Center

    Fegley, Alan D.

    2010-01-01

    The purpose of this EPP is to develop a plan for changing the mindset of a large number of Haddonfield Memorial High School (HMHS) students from a fixed mindset to a growth mindset. HMHS is by most conventional measures a high performing school. Typically 100% of the students graduate with 96% of the students attending two or four year colleges…

  10. No More 1s: High Expectations Can Lead to High Achievement

    ERIC Educational Resources Information Center

    Cervone, Laureen; DiMartino, Lisa; Kerr, Kris

    2010-01-01

    The school district in Middletown, New York, in the state's Orange County, today serves close to 7,000 students in four elementary schools, two middle schools, and one high school. The district is classified by the state in the highest of three Need-to-Resource-Capacity groups, an urban or suburban school district with high student needs in…

  11. Examining the Success Factors of High-Achieving Puerto Rican Male High-School Students

    ERIC Educational Resources Information Center

    Garrett, Tomas; Antrop-Gonzalez, Rene; Velez, William

    2010-01-01

    This article works to dispel the myth that Latino urban high-school students are not capable of performing at high academic levels. Whereas much educational research emphasizes the academic underachievement of urban Latino students, this article counteracts this research by describing the four success factors that three working-class Puerto Rican…

  12. Low Viscosity Highly Concentrated Injectable Nonaqueous Suspensions of Lysozyme Microparticles

    PubMed Central

    Miller, Maria A.; Engstrom, Joshua D.; Ludher, Baltej S.; Johnston, Keith P.

    2011-01-01

    Subcutaneous injection of concentrated protein and peptide solutions, in the range of 100–400 mg/mL, is often not possible with a 25- to 27-gauge needle, as the viscosity can be well above 50 cP. Apparent viscosities below this limit are reported for suspensions of milled lysozyme microparticles up to nearly 400 mg/mL in benzyl benzoate or benzyl benzoate mixtures with safflower oils through a syringe with a 25- to 27-gauge needle at room temperature. These apparent viscosities were confirmed using a cone-and-plate rheometer. The intrinsic viscosity regressed from the Kreiger–Dougherty model was only slightly above the Einstein value of 2.5, indicating the increase in viscosity relative to that of the solvent was caused primarily by the excluded volume. Thus, the increases in viscosity from electrical double layer interactions (electroviscous effects), solvation of the particles, or deviations of the particle shape from a spherical geometry were minimal, and much smaller than typically observed for proteins dissolved in aqueous solutions. The small electroviscous effects are expected given the negligible zeta potential and thin double layers in the low dielectric constant organic solvent. The suspensions were resuspendable after a year, with essentially constant particle size after two months as measured by static light scattering. The lower apparent viscosities for highly concentrated protein suspensions relative to protein solutions, coupled with these favorable characteristics upon resuspension, may offer novel opportunities for subcutaneous injection of therapeutic proteins. PMID:19803503

  13. Unexpectedly high mercury concentration in commercial fish feed

    SciTech Connect

    Choi, H.; Cech, J. Jr.

    1995-12-31

    Unexpectedly high mercury was found in a commercial fish pellet which has been widely used to feed fish in laboratory and fish farm settings. Researchers working with fish in mercury studies need to know that fish pellets contain mercury and consider the pellets, influence in their results. Mean mercury concentration in the commercial fish pellet was 47.4 ug/g (ranging from 35 to 56 ug Hg/g). Total mercury (T-Hg) in the blood of Sacramento blackfish (orthodon microlepidotus), fed the commercial feed for 8 months, was determined by inductively coupled plasma-mass spectrometry (ICP-MS). Mean blood T-Hg reached a steady state at 41 ug Hg/L (ranging from 34 to 51 ug Hg/L) during 5 months of feeding after capture from Clear Lake in California. The accumulation of mercury in blood followed a monoexponential pattern, in accordance with a one-compartment model. There were great variations in mercury levels in blood between individual fishes. The mercury concentrations in the blood did not tend to increase with the growth of the fish. In summary, feed sources of mercury need to be considered in mercury exposure experiments.

  14. Copper Deposits with High Tensile Strength and Elongation Electroformed in an Ultra-Low-Concentration Sulfate Bath without Additives

    NASA Astrophysics Data System (ADS)

    Shen, Chunjian; Zhu, Zengwei; Zhu, Di; Ren, Jianhua

    2017-02-01

    Superior mechanical properties of copper are needed in industries to meet high application requirement. In this study, an electroformed copper with superior mechanical properties is achieved by using a simple ultra-low-concentration copper sulfate bath containing neither chloride nor organic additives. Copper deposits obtained in the copper sulfate concentrations ranging from 30 to 60 g/L exhibit high tensile strength and elongation simultaneously. A maximum tensile strength of 256 MPa is achieved, with an elongation ratio of 31%, at a copper sulfate concentration of 30 g/L, while a maximum elongation ratio of 43% is achieved, with a tensile strength of 216 MPa, at a concentration of 50 g/L. It has been found that the copper sulfate concentration affected the hydrogen content, grain arrangement and orientation index of copper deposits which determine their mechanical properties. When the copper sulfate concentration is less than 30 g/L, the excessive hydrogen content of the deposits thus produced leads to poor compactness and inferior mechanical properties. At concentrations over 50 g/L, a disordered arrangement of grains and a significant increase in the peak of (111) lead to an increase in the tensile strength but a decrease in the elongation ratio. This approach provides an effective and economical method for the copper deposits achieving superior mechanical properties.

  15. Catalytic wet air oxidation of high concentration pharmaceutical wastewater.

    PubMed

    Zhan, Wei; Wang, Xiaocong; Li, Daosheng; Ren, Yongzheng; Liu, Dongqi; Kang, Jianxiong

    2013-01-01

    In this study, we investigated the pretreatment of a high concentration pharmaceutical wastewater by catalytic wet air oxidation (CWAO) process. Different experiments were conducted to investigate the effects of the catalyst type, operating temperature, initial system pH, and oxygen partial pressure on the oxidation of the wastewater. Results show that the catalysts prepared by the co-precipitation method have better catalytic activity compared to others. Chemical oxygen demand (COD) conversion increased with the increase in temperature from 160 to 220 °C and decreased with the increase in pH. Moreover, the effect of the oxygen partial pressure on the COD conversion was significant only during the first 20 min of the reaction. Furthermore, the biodegradability of the wastewater improved greatly after CWAO, the ratio of BOD5/COD increased less than 0.1-0.75 when treated at 220 °C (BOD: biochemical oxygen demand).

  16. Verification of Fresnel lens in high concentration photovoltaic system

    NASA Astrophysics Data System (ADS)

    Wei, An-Chi; Sze, Jyh-Rou; Chern, Jyh-Long

    2012-10-01

    An approach using micro lens arrays to confine the cone angle of light source in a solar simulator has been proposed to verify the Fresnel lens in a high concentration photovoltaic (HCPV) system. Compared with other three prior arts by the computer simulation, the proposed method had the characteristics of the better approximation to the direct normal insolation and the low cost. Also, to ensure the erection of the evaluation system, the tolerance of lens alignment has been analyzed. The results showed that to maintain at least the 50% of the maximum luminous flux incident on the solar cell, the transverse and longitudinal tolerances of ±1.4 mm and ±4 mm, respectively, were required.

  17. Do high concentrations of microcystin prevent Daphnia control of phytoplankton?

    PubMed

    Chislock, Michael F; Sarnelle, Orlando; Jernigan, Lauren M; Wilson, Alan E

    2013-04-15

    Toxin-producing cyanobacteria have frequently been hypothesized to limit the ability of herbivorous zooplankton (such as Daphnia) to control phytoplankton biomass by inhibiting feeding, and in extreme cases, causing zooplankton mortality. Using limnocorral experiments in hyper-eutrophic ponds located in Alabama and Michigan (U.S.A.), we tested the hypothesis that high levels of cyanobacteria and microcystin, a class of hepatotoxins produced by several cyanobacterial genera, prevent Daphnia from strongly reducing phytoplankton abundance. At the start of the first experiment (Michigan), phytoplankton communities were dominated by toxic Microcystis and Anabaena (∼96% of total phytoplankton biomass), and concentrations of microcystin were ∼3 μg L⁻¹. Two weeks after adding Daphnia pulicaria from a nearby eutrophic lake, microcystin levels increased to ∼6.5 μg L⁻¹, yet Daphnia populations increased exponentially (r = 0.24 day⁻¹). By the third week, Daphnia had suppressed phytoplankton biomass by ∼74% relative to the no Daphnia controls and maintained reduced phytoplankton biomass until the conclusion of the five-week experiment. In the second experiment (Alabama), microcystin concentrations were greater than 100 μg L⁻¹, yet a mixture of three D. pulicaria clones from eutrophic lakes in southern MI increased and again reduced phytoplankton biomass, in this case by over 80%. The ability of Daphnia to increase in abundance and suppress phytoplankton biomass, despite high initial levels of cyanobacteria and microcystin, indicates that the latter does not prevent strong control of phytoplankton biomass by Daphnia genotypes that are adapted to environments with abundant cyanobacteria and associated cyanotoxins.

  18. Modeling stability of growth between mathematics and science achievement during middle and high school.

    PubMed

    Ma, Xin; Ma, Lingling

    2004-04-01

    In this study, the authors introduced a multivariate multilevel model to estimate the consistency among students and schools in the rates of growth between mathematics and science achievement during the entire middle and high school years with data from the Longitudinal Study of American Youth (LSAY). There was no evident consistency in the rates of growth between mathematics and science achievement among students, and this inconsistency was not much influenced by student characteristics and school characteristics. However, there was evident consistency in the average rates of growth between mathematics and science achievement among schools, and this consistency was influenced by student characteristics and school characteristics. Major school-level variables associated with parental involvement did not show any significant impacts on consistency among either students or schools. Results call for educational policies that promote collaboration between mathematics and science departments or teachers.

  19. The preparation and ethanol fermentation of high-concentration sugars from steam-explosion corn stover.

    PubMed

    Xie, Hui; Wang, Fengqin; Yin, Shuangyao; Ren, Tianbao; Song, Andong

    2015-05-01

    In the field of biofuel ethanol, high-concentration- reducing sugars made from cellulosic materials lay the foundation for high-concentration ethanol fermentation. In this study, corn stover was pre-treated in a process combining chemical methods and steam explosion; the cellulosic hydrolyzed sugars obtained by fed-batch saccharification were then used as the carbon source for high-concentration ethanol fermentation. Saccharomyces cerevisiae 1308, Angel yeast, and Issatchenkia orientalis were shake-cultured with Pachysolen tannophilus P-01 for fermentation. Results implied that the ethanol yields from the three types of mixed strains were 4.85 g/100 mL, 4.57 g/100 mL, and 5.02 g/100 mL (separately) at yield rates of 91.6, 89.3, and 92.2%, respectively. Therefore, it was inferred that shock-fermentation using mixed strains achieved a higher ethanol yield at a greater rate in a shorter fermentation period. This study provided a theoretical basis and technical guidance for the fermentation of industrial high-concentrated cellulosic ethanol.

  20. Characterization of personal exposure concentration of fine particles for adults and children exposed to high ambient concentrations in Beijing, China.

    PubMed

    Du, Xuan; Kong, Qian; Ge, Weihua; Zhang, Shaojun; Fu, Lixin

    2010-01-01

    In China, the health risk from overexposure to particles is becoming an important public health concern. To investigate daily exposure characteristics to PM2.5 with high ambient concentration in urban area, a personal exposure study was conducted for school children, and office workers in Beijing, China. For all participants (N = 114), the mean personal 24-hr exposure concentration was 102.5, 14.7, 0.093, 0.528, 0.934, 0.174 and 0.703 microg/m3 for PM2.5, black carbon, Mn, Al, Ca, Pb, and Fe. Children's exposure concentrations of PM2.5 were 4-5 times higher than those in related studies. The ambient concentration of PM2.5 (128.5 microg/m3) was significantly higher than the personal exposure concentration (P < 0.05), and exceed the reference concentration (25 microg/m3) of WHO air quality guideline. Good correlation relationships and significant differences were identified between ambient concentration and personal exposure concentration. The relationships indicate that the ambient concentration is the main factor influencing personal exposure concentration, but is not a good indicator of personal exposure concentration. Outdoor activities (commute mode, exposure to heating, workday or weekend travel) influenced personal exposure concentrations significantly, but the magnitude of the influence from indoor activities (exposure to cooking) was masked by the high ambient concentrations.

  1. Relationship of constructivist learning environment to student attitudes and achievement in high school mathematics and science

    NASA Astrophysics Data System (ADS)

    Dethlefs, Theresa Marie

    This study investigated the relationship of constructivist learning environment and standards-based teaching practices to student achievement and attitudes (self-efficacy, intrinsic value, and learning strategies) in Algebra and Biology. Further, these relationships were examined as a function of student gender and prior achievement. A purposive sample of 804 high school students enrolled in Biology I, Algebra I, or Advanced Algebra was selected for inclusion in this study. Although the dimensions of constructivist learning environment that contributed to predicting student achievement and attitudes varied by content area and criterion, the results of the present study generally provide strong support for a positive relationship between constructivist learning environment and student attitudes, but little support for a direct relationship to student achievement. Teacher reports of overall constructivist learning environment were not correlated with achievement or attitudes. Observer reports of constructivist learning environment were correlated with student intrinsic value and learning strategies. Student reports of constructivist learning environment were correlated with all three attitude measures. Multiple regression findings showed that neither overall constructivist learning environment nor standards-based teaching practices predicted achievement in any of the content areas. Overall constructivist learning environment and standards-based teaching practices were significant positive predictors of student intrinsic value and learning strategies in all three content areas, after controlling for student and classroom demographic variables. Overall constructivist learning environment and standards-based teaching practices were also significant positive predictors of self-efficacy in Algebra 1. In addition, standards-based teaching practices was a significant positive predictor of student self-efficacy in Biology. No specific dimensions of constructivist learning

  2. Peace of Mind, Academic Motivation, and Academic Achievement in Filipino High School Students.

    PubMed

    Datu, Jesus Alfonso D

    2017-04-09

    Recent literature has recognized the advantageous role of low-arousal positive affect such as feelings of peacefulness and internal harmony in collectivist cultures. However, limited research has explored the benefits of low-arousal affective states in the educational setting. The current study examined the link of peace of mind (PoM) to academic motivation (i.e., amotivation, controlled motivation, and autonomous motivation) and academic achievement among 525 Filipino high school students. Findings revealed that PoM was positively associated with academic achievement β = .16, p < .05, autonomous motivation β = .48, p < .001, and controlled motivation β = .25, p < .01. As expected, PoM was negatively related to amotivation β = -.19, p < .05, and autonomous motivation was positively associated with academic achievement β = .52, p < .01. Furthermore, the results of bias-corrected bootstrap analyses at 95% confidence interval based on 5,000 bootstrapped resamples demonstrated that peace of mind had an indirect influence on academic achievement through the mediating effects of autonomous motivation. In terms of the effect sizes, the findings showed that PoM explained about 1% to 18% of the variance in academic achievement and motivation. The theoretical and practical implications of the results are elucidated.

  3. The role of chronotype, gender, test anxiety, and conscientiousness in academic achievement of high school students.

    PubMed

    Rahafar, Arash; Maghsudloo, Mahdis; Farhangnia, Sajedeh; Vollmer, Christian; Randler, Christoph

    2016-01-01

    Previous findings have demonstrated that chronotype (morningness/intermediate/eveningness) is correlated with cognitive functions, that is, people show higher mental performance when they do a test at their preferred time of day. Empirical studies found a relationship between morningness and higher learning achievement at school and university. However, only a few of them controlled for other moderating and mediating variables. In this study, we included chronotype, gender, conscientiousness and test anxiety in a structural equation model (SEM) with grade point average (GPA) as academic achievement outcome. Participants were 158 high school students and results revealed that boys and girls differed in GPA and test anxiety significantly, with girls reporting better grades and higher test anxiety. Moreover, there was a positive correlation between conscientiousness and GPA (r = 0.17) and morningness (r = 0.29), respectively, and a negative correlation between conscientiousness and test anxiety (r = -0.22). The SEM demonstrated that gender was the strongest predictor of academic achievement. Lower test anxiety predicted higher GPA in girls but not in boys. Additionally, chronotype as moderator revealed a significant association between gender and GPA for evening types and intermediate types, while intermediate types showed a significant relationship between test anxiety and GPA. Our results suggest that gender is an essential predictor of academic achievement even stronger than low or absent test anxiety. Future studies are needed to explore how gender and chronotype act together in a longitudinal panel design and how chronotype is mediated by conscientiousness in the prediction of academic achievement.

  4. High fat diet promotes achievement of peak bone mass in young rats

    SciTech Connect

    Malvi, Parmanand; Piprode, Vikrant; Chaube, Balkrishna; Pote, Satish T.; Mittal, Monika; Chattopadhyay, Naibedya; Wani, Mohan R.; Bhat, Manoj Kumar

    2014-12-05

    Highlights: • High fat diet helps in achieving peak bone mass at younger age. • Shifting from high fat to normal diet normalizes obese parameters. • Bone parameters are sustained even after withdrawal of high fat diet. - Abstract: The relationship between obesity and bone is complex. Epidemiological studies demonstrate positive as well as negative correlation between obesity and bone health. In the present study, we investigated the impact of high fat diet-induced obesity on peak bone mass. After 9 months of feeding young rats with high fat diet, we observed obesity phenotype in rats with increased body weight, fat mass, serum triglycerides and cholesterol. There were significant increases in serum total alkaline phosphatase, bone mineral density and bone mineral content. By micro-computed tomography (μ-CT), we observed a trend of better trabecular bones with respect to their microarchitecture and geometry. This indicated that high fat diet helps in achieving peak bone mass and microstructure at younger age. We subsequently shifted rats from high fat diet to normal diet for 6 months and evaluated bone/obesity parameters. It was observed that after shifting rats from high fat diet to normal diet, fat mass, serum triglycerides and cholesterol were significantly decreased. Interestingly, the gain in bone mineral density, bone mineral content and trabecular bone parameters by HFD was retained even after body weight and obesity were normalized. These results suggest that fat rich diet during growth could accelerate achievement of peak bone mass that is sustainable even after withdrawal of high fat diet.

  5. Computer-Based Drill and Practice in Arithmetic: Widening the Gap between High- and Low-Achieving Students.

    ERIC Educational Resources Information Center

    Hativa, Nira

    1988-01-01

    The differential effects of computer-assisted instruction for high-achieving and low-achieving students were examined for seven elementary students of varied background. Higher-achieving students were more able to adjust to the requirements of computer work and to derive benefit from it than were lower-achieving students. Implications for teaching…

  6. Achievement Motivation of the High School Students: A Case Study among Different Communities of Goalpara District of Assam

    ERIC Educational Resources Information Center

    Sarangi, C.

    2015-01-01

    Achievement motivation is a consistent striving force of an individual to achieve success to a certain standard of excellence in competing situation. In this study an attempt was made to study the effect of achievement motivation on the academic achievement of the high school students of tribal and non tribal communities in relation to their sex…

  7. Fat-soluble vitamin and micromineral concentrations in preruminant dairy calves fed to achieve different growth rates

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Calf nutrition programs often limit nutrient intake from milk replacer during the first few weeks of life to promote dry-feed intake and early weaning. Recent studies indicate that feeding increased amounts of milk replacer with higher protein concentration improves growth performance and feed effi...

  8. Microbial production of itaconic acid: developing a stable platform for high product concentrations.

    PubMed

    Kuenz, Anja; Gallenmüller, Yvonne; Willke, Thomas; Vorlop, Klaus-Dieter

    2012-12-01

    Biotechnologically produced itaconic acid (IA) is a promising organic acid with a wide range of applications and the potential to open up new application fields in the area of polymer chemistry, pharmacy, and agriculture. In this study, a systematic process optimization was performed with an own isolated strain of Aspergillus terreus and transferred from a 250-mL to a 15-L scale. An IA concentration of 86.2 g/L was achieved within 7 days with an overall productivity of 0.51 g/(L h), a maximum productivity of 1.2 g/(L h), and a yield of 86 mol%. A cultivation of other well-known A. terreus strains with the developed process showed no significant differences. Based on this, a process is developed providing a high final IA concentration independent of the used strain combined with high reproducibility.

  9. Multiple liquid crystal phases of DNA at high concentrations.

    PubMed

    Strzelecka, T E; Davidson, M W; Rill, R L

    1988-02-04

    DNA packaging in vivo is very tight, with volume concentrations approaching 70% w/v in sperm heads, virus capsids and bacterial nucleoids. The packaging mechanisms adopted may be related to the natural tendency of semi-rigid polymers to form liquid crystalline phases in concentrated solutions. We find that DNA forms at least three distinct liquid crystalline phases at concentrations comparable to those in vivo, with phase transitions occurring over relatively narrow ranges of DNA concentration. A weakly birefringent, dynamic, 'precholesteric' mesophase with microscopic textures intermediate between those of a nematic and a true cholesteric phase forms at the lowest concentrations required for phase separation. At slightly higher DNA concentrations, a second mesophase forms which is a strongly birefringent, well-ordered cholesteric phase with a concentration-dependent pitch varying from 2 to 10 micron. At the highest DNA concentrations, a phase forms which is two-dimensionally ordered and resembles smectic phases of thermotropic liquid crystals observed with small molecules.

  10. Modelling acceptance of sunlight in high and low photovoltaic concentration

    SciTech Connect

    Leutz, Ralf

    2014-09-26

    A simple model incorporating linear radiation characteristics, along with the optical trains and geometrical concentration ratios of solar concentrators is presented with performance examples for optical trains of HCPV, LCPV and benchmark flat-plate PV.

  11. High Temperature Concentrated Solar Power Using Liquid Metal

    NASA Astrophysics Data System (ADS)

    Henry, Asegun

    One of the most attractive ways to try and reduce the cost of concentrated solar power (CSP) is to increase the system efficiency and the biggest loss in the system occurs in the conversion of heat to electricity via heat engine. Heat engines that utilize turbomachinery currently operate near their thermodynamic limitations and thus one of the only ways to improve heat engine efficiency is to increase the turbine inlet temperature. Significant effort is being devoted to the development of supercritical CO2 heat engines, but the most efficient heat engines are combined cycles, which reach efficiencies as high as 60%. However, such heat engines require turbine inlet temperatures ~1300-1500C, which is far beyond what is currently feasible with the state of the art molten salt infrastructure. In working towards the development of a system that can operate in the 1300-1500C temperature range, the most significant challenges lie in the materials and forming functional and reliable components out of new materials. One of the most attractive options from a cost and heat transfer perspective is to use liquid metals, such as tin and aluminum-silicon alloys along with a ceramic based infrastructure. This talk will overview ongoing efforts in the Atomistic Simulation and Energy (ASE) research group at Georgia Tech to develop prototype components such as an efficient high temperature cavity receiver, pumps and valves that can make a liquid metal based CSP infrastructure realizable.

  12. High-performance deployable structures for the support of high-concentration ratio solar array modules

    NASA Technical Reports Server (NTRS)

    Mobrem, M.

    1985-01-01

    A study conducted on high-performance deployable structures for the support of high-concentration ratio solar array modules is discussed. Serious consideration is being given to the use of high-concentration ratio solar array modules or applications such as space stations. These concentrator solar array designs offer the potential of reduced cost, reduced electrical complexity, higher power per unit area, and improved survivability. Arrays of concentrators, such as the miniaturized Cassegrainian concentrator modules, present a serious challenge to the structural design because their mass per unit area (5.7 kg/square meters) is higher than that of flexible solar array blankets, and the requirement for accurate orientation towards the Sun (plus or minus 0.5 degree) requires structures with improved accuracy potentials. In addition, use on a space station requires relatively high structural natural frequencies to avoid deleterious interactions with control systems and other large structural components. The objective here is to identify and evaluate conceptual designs of structures suitable for deploying and accurately supporting high-concentration ratio solar array modules.

  13. Solvent additive to achieve highly ordered nanostructural semicrystalline DPP copolymers: toward a high charge carrier mobility.

    PubMed

    An, Tae Kyu; Kang, Il; Yun, Hui-jun; Cha, Hyojung; Hwang, Jihun; Park, Seonuk; Kim, Jiye; Kim, Yu Jin; Chung, Dae Sung; Kwon, Soon-Ki; Kim, Yun-Hi; Park, Chan Eon

    2013-12-23

    A facile spin-coating method in which a small percentage of the solvent additive, 1-chloronaphthalene (CN), is found to increase the drying time during film deposition, is reported. The field-effect mobility of a PDPPDBTE film cast from a chloroform-CN mixed solution is 0.46 cm(2) V(-1) s(-1). The addition of CN to the chloroform solution facilitates the formation of highly crystalline polymer structures.

  14. Challenges to achievement of metal sustainability in our high-tech society

    SciTech Connect

    Izatt, Reed M.; Izatt, Steven R.; Bruening, Ronald L.; Izatt, Neil; Moyer, Bruce A

    2014-01-01

    Achievement of sustainability in metal life cycles from mining of virgin ore to consumer and industrial devices to end-of-life products requires greatly increased recycling and improved processing of metals. Electronic and other high-tech products containing precious, toxic, and specialty metals usually have short lifetimes and low recycling rates. Products containing these metals generally are incinerated, discarded as waste in landfills, or dismantled in informal recycling using crude and environmentally irresponsible procedures. Low metal recycling rates coupled with increasing demand for products containing them necessitate increased mining with attendant environmental, health, energy, water, and carbon-footprint consequences. In this tutorial review, challenges to achieving metal sustainability in present high-tech society are presented; health, environmental, and economic incentives for various stakeholders to improve metal sustainability are discussed; a case for technical improvements in separations technology, especially employing molecular recognition, is given; and global consequences of continuing on the present path are examined.

  15. Ethanol in pre-surgical hand rubs: concentration and duration of application for achieving European Norm EN 12791.

    PubMed

    Suchomel, M; Rotter, M

    2011-03-01

    In Europe, ethanol is a common active agent in hand rub formulations and nowadays it is also recommended in guidelines for hand hygiene published by the Centers for Disease Control and Prevention and by the World Health Organization. However, data on the range of concentrations and durations of application providing a basis for passing the efficacy test of the European norm EN 12791 are still lacking. Therefore, the bactericidal efficacy of rubbing clean hands with pure ethanol in volume concentrations of 95%, 85% or 75% during 3 min was compared with that of the reference procedure of EN 12791 employing n-propanol 60% v/v for 3 min, immediately and 3h after disinfection. Ethanol 85% was also tested at a 5 min application. A Latin-square design was used with 20 randomly allotted volunteers. Whereas the mean immediate bacterial reductions caused by ethanol at concentrations of 75% (log RF 1.68) and 95% (log RF 2.70) were significantly less efficacious compared to that of the reference (log RF 3.27), at 85% they were not significantly less active with both applications, 3 and 5 min (log RFs 2.90 and 3.12, respectively). Three hours after antisepsis, the bacterial reduction on the gloved hand was only significantly less efficacious than that of the reference when 75% ethanol was used. It is concluded that ethanol-based hand rubs have a good chance of meeting the EN 12791 requirements if their ethanol concentration is >75% v/v but <95% v/v and if they are applied for at least 3 min.

  16. Quality evaluation of moluodan concentrated pill using high-performance liquid chromatography fingerprinting coupled with chemometrics.

    PubMed

    Tao, Lingyan; Zhang, Qing; Wu, Yongjiang; Liu, Xuesong

    2016-12-01

    In this study, a fast and effective high-performance liquid chromatography method was developed to obtain a fingerprint chromatogram and quantitative analysis simultaneously of four indexes including gallic acid, chlorogenic acid, albiflorin and paeoniflorin of the traditional Chinese medicine Moluodan Concentrated Pill. The method was performed by using a Waters X-bridge C18 reversed phase column on an Agilent 1200S high-performance liquid chromatography system coupled with diode array detection. The mobile phase of the high-performance liquid chromatography method was composed of 20 mmol/L phosphate solution and acetonitrile with a 1 mL/min eluent velocity, under a detection temperature of 30°C and a UV detection wavelength of 254 nm. After the methodology validation, 16 batches of Moluodan Concentrated Pill were analyzed by this high-performance liquid chromatography method and both qualitative and quantitative evaluation results were achieved by similarity analysis, principal component analysis and hierarchical cluster analysis. The results of these three chemometrics were in good agreement and all indicated that batch 10 and batch 16 showed significant differences with the other 14 batches. This suggested that the developed high-performance liquid chromatography method could be applied in the quality evaluation of Moluodan Concentrated Pill.

  17. Achieving High Pressure Shock Hugoniot Measurements in Cylindrical Geometry Utilizing a High-Explosive Pulsed Power Drive

    DTIC Science & Technology

    2011-06-01

    to conduct high velocity material experiments and measure shock velocities at pressures near 1 TPa. The DEMG (Disk Explosive Magnetic Generator ... Explosive Magnetic Generator ) will be able to achieve extremely high currents with as much as 70 MA usable for driving a z-pinch experiment. In this...shock velocities at pressures near 1 TPa. The DEMG (Disk Explosive Magnetic Generator ) is used to drive a >60MA current that accelerates an aluminum

  18. The high heritability of educational achievement reflects many genetically influenced traits, not just intelligence

    PubMed Central

    Krapohl, Eva; Rimfeld, Kaili; Shakeshaft, Nicholas G.; Trzaskowski, Maciej; McMillan, Andrew; Pingault, Jean-Baptiste; Asbury, Kathryn; Harlaar, Nicole; Kovas, Yulia; Dale, Philip S.; Plomin, Robert

    2014-01-01

    Because educational achievement at the end of compulsory schooling represents a major tipping point in life, understanding its causes and correlates is important for individual children, their families, and society. Here we identify the general ingredients of educational achievement using a multivariate design that goes beyond intelligence to consider a wide range of predictors, such as self-efficacy, personality, and behavior problems, to assess their independent and joint contributions to educational achievement. We use a genetically sensitive design to address the question of why educational achievement is so highly heritable. We focus on the results of a United Kingdom-wide examination, the General Certificate of Secondary Education (GCSE), which is administered at the end of compulsory education at age 16. GCSE scores were obtained for 13,306 twins at age 16, whom we also assessed contemporaneously on 83 scales that were condensed to nine broad psychological domains, including intelligence, self-efficacy, personality, well-being, and behavior problems. The mean of GCSE core subjects (English, mathematics, science) is more heritable (62%) than the nine predictor domains (35–58%). Each of the domains correlates significantly with GCSE results, and these correlations are largely mediated genetically. The main finding is that, although intelligence accounts for more of the heritability of GCSE than any other single domain, the other domains collectively account for about as much GCSE heritability as intelligence. Together with intelligence, these domains account for 75% of the heritability of GCSE. We conclude that the high heritability of educational achievement reflects many genetically influenced traits, not just intelligence. PMID:25288728

  19. The high heritability of educational achievement reflects many genetically influenced traits, not just intelligence.

    PubMed

    Krapohl, Eva; Rimfeld, Kaili; Shakeshaft, Nicholas G; Trzaskowski, Maciej; McMillan, Andrew; Pingault, Jean-Baptiste; Asbury, Kathryn; Harlaar, Nicole; Kovas, Yulia; Dale, Philip S; Plomin, Robert

    2014-10-21

    Because educational achievement at the end of compulsory schooling represents a major tipping point in life, understanding its causes and correlates is important for individual children, their families, and society. Here we identify the general ingredients of educational achievement using a multivariate design that goes beyond intelligence to consider a wide range of predictors, such as self-efficacy, personality, and behavior problems, to assess their independent and joint contributions to educational achievement. We use a genetically sensitive design to address the question of why educational achievement is so highly heritable. We focus on the results of a United Kingdom-wide examination, the General Certificate of Secondary Education (GCSE), which is administered at the end of compulsory education at age 16. GCSE scores were obtained for 13,306 twins at age 16, whom we also assessed contemporaneously on 83 scales that were condensed to nine broad psychological domains, including intelligence, self-efficacy, personality, well-being, and behavior problems. The mean of GCSE core subjects (English, mathematics, science) is more heritable (62%) than the nine predictor domains (35-58%). Each of the domains correlates significantly with GCSE results, and these correlations are largely mediated genetically. The main finding is that, although intelligence accounts for more of the heritability of GCSE than any other single domain, the other domains collectively account for about as much GCSE heritability as intelligence. Together with intelligence, these domains account for 75% of the heritability of GCSE. We conclude that the high heritability of educational achievement reflects many genetically influenced traits, not just intelligence.

  20. Motivational profiles in high school students: Differences in behavioural and emotional homework engagement and academic achievement.

    PubMed

    Regueiro, Bibiana; Núñez, José C; Valle, Antonio; Piñeiro, Isabel; Rodríguez, Susana; Rosário, Pedro

    2016-12-12

    This work examined whether combinations of academic and non-academic goals generated different motivational profiles in high school students. Besides, differences in homework behavioural engagement (i.e. amount of homework, time spent in homework, homework time management), homework emotional engagement (i.e. homework anxiety) and academic achievement were analysed. Participants were 714 high school students (43.4% boys and 56.6% girls). The study of potential motivational profiles was conducted by latent profile analysis, and the differences between the motivational profiles regarding homework variables and academic achievement were analysed using multivariate analysis. The results indicate the existence of five groups of motivational profiles: a group of students with multiple goals, a group of unmotivated students, two groups of students with a predominance of learning goals and, finally, a group comprising students with a high fear of failure. Both the group with multiple goals and the learning goals-oriented groups reported to do more homework, spending more time on homework, making better use of that time and having a higher academic achievement than counterparts. The avoidance-failure group and the group with multiple goals showed higher levels of homework anxiety. Globally, these results provide support for a person-centred approach.

  1. Family Processes, SES, and Family Structure Differentially Affect Academic Self-Concepts and Achievement of Gifted High School Students.

    ERIC Educational Resources Information Center

    Verna, Marilyn Ann; Campbell, James Reed; Beasley, Mark

    A study involving 109 male and 116 female high achieving high school students (ages 16-18) and their parents investigated the causal linkages among home environment, self-concepts, prior ability, and socioeconomic status on mathematics achievement, science achievement, and Scholastic Aptitude Test-Quantitative (SAT-Q) and Verbal scores. Students…

  2. 27 CFR 18.52 - Production of high-proof concentrate.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Production of high-proof... § 18.52 Production of high-proof concentrate. (a) General. High-proof concentrate may be produced in a... whether a particular concentrate is a high-proof concentrate. However, a proprietor may at any time...

  3. Achieving high strength and high electrical conductivity in Ag/Cu multilayers

    NASA Astrophysics Data System (ADS)

    Wei, M. Z.; Xu, L. J.; Shi, J.; Pan, G. J.; Cao, Z. H.; Meng, X. K.

    2015-01-01

    In this work, we investigated the microstructure evolution of Ag/Cu multilayers and its influences on the hardness and electric resistivity with individual layer thickness (h) ranging from 3 to 50 nm. The hardness increases with the decreasing h in the range of 5-20 nm. The barrier to dislocation transmission by stacking faults, twin boundaries, and interfaces leads to hardness enhancement. Simultaneously, in order to get high conductivity, the strong textures in-layers were induced to form for reducing the amount of grain boundaries. The resistivity keeps low even when h decreases to 10 nm. Furthermore, we developed a facile model to evaluate the comprehensive property of Ag/Cu multilayers—the results indicate that the best combination of strength and conductivity occurs when h = 10 nm.

  4. Dry Blending to Achieve Isotopic Dilution of Highly Enriched Uranium Oxide Materials

    SciTech Connect

    Henry, Roger Neil; Chipman, Nathan Alan; Rajamani, R. K.

    2001-04-01

    The end of the cold war produced large amounts of excess fissile materials in the United States and Russia. The Department of Energy has initiated numerous activities to focus on identifying material management strategies for disposition of these excess materials. To date, many of these planning strategies have included isotopic dilution of highly enriched uranium as a means of reducing the proliferation and safety risks. Isotopic dilution by dry blending highly enriched uranium with natural and/or depleted uranium has been identified as one non-aqueous method to achieve these risk (proliferation and criticality safety) reductions. This paper reviews the technology of dry blending as applied to free flowing oxide materials.

  5. Denitrification of high nitrate concentration wastewater using alternative carbon sources.

    PubMed

    Fernández-Nava, Y; Marañón, E; Soons, J; Castrillón, L

    2010-01-15

    The use of different organic carbon sources in the denitrification of wastewater containing 2500 mg nitrates/L in a SBR was studied. Three alternative sources of carbon were tested: wastewater from a sweet factory, a residue from a soft drinks factory and a residue from a dairy plant. The first two are sugar-rich, whereas the third presents a high content in lactic acid. Maximum specific denitrification rates of between 42 and 48 mg NO(3)-N/g VSS h were obtained. The effluents were nitrate-free and very low COD concentrations were obtained in 4-6h reaction time, especially with the sugar-rich carbon sources. The values of the denitrifier net yield coefficient were higher than when using methanol (0.93-1.75 g VSS(formed)/g NO(x)-N(reduced)). The lowest value was obtained using the lactic acid-rich residue. The optimum COD/N ratios varied between 4.6 for the lactic acid-rich carbon source and 5.5-6.5 for the sugar-rich carbon sources.

  6. Progress toward achieving high power and high efficiency semipolar LEDs and their characterization

    NASA Astrophysics Data System (ADS)

    Zhong, Hong

    Performance of current commercially available wurtzite nitride based light-emitting diodes (LEDs), grown along the polar (0001) c-plane orientation, is limited by the presence of polarization-related electric fields inside multi-quantum wells (MQWs). The discontinuities in both spontaneous and piezoelectric polarization at the heterointerfaces result in internal electric fields in the quantum wells. These electric fields cause carrier separation [quantum confined Stark effect (QCSE)] and reduce the radiative recombination rate within the quantum wells. One approach to reduce and possibly eliminate the polarization-related effects is to grow III-nitride devices on crystal planes that are inclined with respect to the c-axis, i.e., on semipolar planes. In this dissertation, metalorganic chemical vapor deposition (MOCVD) has been employed for the homoepitaxial growth of GaN based LEDs on semipolar orientations. As a consequence of growing on high-quality bulk GaN substrates, the LEDs have significantly reduced threading dislocation and stacking fault densities, resulting in remarkable improvements in EQE and output power. High efficiency semipolar (1011) violet-blue and blue LEDs have been demonstrated without any intentional effort to enhance the light extraction from those devices. Optimizations of epitaxial structures have led to increased output power and external quantum efficiency. A silicone encapsulated single quantum well blue LED with peak wavelength of 444 nm with output power of 24.3 mW, external quantum efficiency of 43% and luminous efficacy of 75 lm/W (with phosphorescent coating) at 20 mA has been demonstrated. Polarization fields in strained (1011) and (112¯2) InGaN quantum wells have been experimentally determined through bias-dependent optical studies. Our results show that the polarization field flips its direction in semipolar InGaN quantum wells with large inclination angles (i.e. around 60°). This suggests that there exists a polarization

  7. Achieving the Middle Ground in an Age of Concentrated Extremes: Mixed Middle-Income Neighborhoods and Emerging Adulthood

    PubMed Central

    SAMPSON, ROBERT J.; MARE, ROBERT D.; PERKINS, KRISTIN L.

    2015-01-01

    This article focuses on stability and change in “mixed middle-income” neighborhoods. We first analyze variation across nearly two decades for all neighborhoods in the United States and in the Chicago area, particularly. We then analyze a new longitudinal study of almost 700 Chicago adolescents over an 18-year span, including the extent to which they are exposed to different neighborhood income dynamics during the transition to young adulthood. The concentration of income extremes is persistent among neighborhoods, generally, but mixed middle-income neighborhoods are more fluid. Persistence also dominates among individuals, though Latino-Americans are much more likely than African Americans or whites to be exposed to mixed middle-income neighborhoods in the first place and to transition into them over time, even when adjusting for immigrant status, education, income, and residential mobility. The results here enhance our knowledge of the dynamics of income inequality at the neighborhood level, and the endurance of concentrated extremes suggests that policies seeking to promote mixed-income neighborhoods face greater odds than commonly thought. PMID:26722129

  8. Adaptation of a mixed culture of acidophiles for a tank biooxidation of refractory gold concentrates containing a high concentration of arsenic.

    PubMed

    Hong, Jeongsik; Silva, Rene A; Park, Jeonghyun; Lee, Eunseong; Park, Jayhyun; Kim, Hyunjung

    2016-05-01

    We adapted a mixed culture of acidophiles to high arsenic concentrations to confirm the possibility of achieving more than 70% biooxidation of refractory gold concentrates containing high arsenic (As) concentration. The biooxidation process was applied to refractory gold concentrates containing approximately 139.67 g/kg of total As in a stirred tank reactor using an adapted mixed culture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans. The percentage of the biooxidation process was analyzed based on the total As removal efficiency. The As removal was monitored by inductively coupled plasma (ICP) analysis, conducted every 24 h. The results obtained with the adapted culture were compared with the percentage of biooxidation obtained with a non-adapted mixed culture of A. ferrooxidans and A. thiooxidans, and with their respective pure cultures. The percentages of biooxidation obtained during 358 h of reaction were 72.20%, 38.20%, 27.70%, and 11.45% for adapted culture, non-adapted culture, and pure cultures of A. thiooxidans and A. ferrooxidans, respectively. The adapted culture showed a peak maximum percentage of biooxidation of 77% at 120 h of reaction, confirming that it is possible to obtain biooxidation percentages over 70% in gold concentrates containing high As concentrations.

  9. A Study of Gifted High, Moderate, and Low Achievers in Their Personal Characteristics and Attitudes toward School and Teachers

    ERIC Educational Resources Information Center

    Abu-Hamour, Bashir; Al-Hmouz, Hanan

    2013-01-01

    This study examines the problem of underachievement among gifted high school students. Low achievers were compared to high and moderate achievers on their motivation, self-regulation, and attitudes toward their school and teachers. Participants were all highly able students from grades 10 and 11 in an academically selective gifted high school in…

  10. High performances CNTFETs achieved using CNT networks for selective gas sensing

    NASA Astrophysics Data System (ADS)

    Gorintin, Louis; Bondavalli, Paolo; Legagneux, Pierre; Pribat, Didier

    2009-08-01

    Our study deals with the utilization of carbon nanotubes networks based transistors with different metal electrodes for highly selective gas sensing. Indeed, carbon nanotubes networks can be used as semi conducting materials to achieve good performances transistors. These devices are extremely sensitive to the change of the Schottky barrier heights between Single Wall Carbon Nanotubes (SWCNTs) and drain/source metal electrodes: the gas adsorption creates an interfacial dipole that modifies the metal work function and so the bending and the height of the Schottky barrier at the contacts. Moreover each gas interacts specifically with each metal identifying a sort of electronic fingerprinting. Using airbrush technique for deposition, we have been able to achieve uniform random networks of carbon nanotubes suitable for large area applications and mass production such as fabrication of CNT based gas sensors. These networks enable us to achieve transistors with on/off ratio of more than 5 orders of magnitude. To reach these characteristics, the density of the CNT network has been adjusted in order to reach the percolation threshold only for semi-conducting nanotubes. These optimized devices have allowed us to tune the sensitivity (improving it) of our sensors for highly selective detection of DiMethyl-Methyl-Phosphonate (DMMP, a sarin stimulant), and even volatile drug precursors using Pd, Au and Mo electrodes.

  11. Achieving High Spatial Resolution Surface Plasmon Resonance Microscopy with Image Reconstruction.

    PubMed

    Yu, Hui; Shan, Xiaonan; Wang, Shaopeng; Tao, Nongjian

    2017-03-07

    Surface plasmon resonance microscopy (SPRM) is a powerful platform for biomedical imaging and molecular binding kinetics analysis. However, the spatial resolution of SPRM along the plasmon propagation direction (longitudinal) is determined by the decaying length of the plasmonic wave, which can be as large as tens of microns. Different methods have been proposed to improve the spatial resolution, but each at the expense of decreased sensitivity or temporal resolution. Here we present a method to achieve high spatial resolution SPRM based on deconvolution of complex field. The method does not require additional optical setup and improves the spatial resolution in the longitudinal direction. We applied the method to image nanoparticles and achieved close-to-diffraction limit resolution in both longitudinal and transverse directions.

  12. The effects of modeling instruction on high school physics academic achievement

    NASA Astrophysics Data System (ADS)

    Wright, Tiffanie L.

    The purpose of this study was to explore whether Modeling Instruction, compared to traditional lecturing, is an effective instructional method to promote academic achievement in selected high school physics classes at a rural middle Tennessee high school. This study used an ex post facto , quasi-experimental research methodology. The independent variables in this study were the instructional methods of teaching. The treatment variable was Modeling Instruction and the control variable was traditional lecture instruction. The Treatment Group consisted of participants in Physical World Concepts who received Modeling Instruction. The Control Group consisted of participants in Physical Science who received traditional lecture instruction. The dependent variable was gains scores on the Force Concepts Inventory (FCI). The participants for this study were 133 students each in both the Treatment and Control Groups (n = 266), who attended a public, high school in rural middle Tennessee. The participants were administered the Force Concepts Inventory (FCI) prior to being taught the mechanics of physics. The FCI data were entered into the computer-based Statistical Package for the Social Science (SPSS). Two independent samples t-tests were conducted to answer the research questions. There was a statistically significant difference between the treatment and control groups concerning the instructional method. Modeling Instructional methods were found to be effective in increasing the academic achievement of students in high school physics. There was no statistically significant difference between FCI gains scores for gender. Gender was found to have no effect on the academic achievement of students in high school physics classes. However, even though there was not a statistically significant difference, female students' gains scores were higher than male students' gains scores when Modeling Instructional methods of teaching were used. Based on these findings, it is recommended

  13. Oxygen concentration control of dopamine-induced high uniformity surface coating chemistry.

    PubMed

    Kim, Hyo Won; McCloskey, Bryan D; Choi, Tae Hwan; Lee, Changho; Kim, Min-Joung; Freeman, Benny D; Park, Ho Bum

    2013-01-23

    Material surface engineering has attracted great interest in important applications, including electronics, biomedicine, and membranes. More recently, dopamine has been widely exploited in solution-based chemistry to direct facile surface modification. However, unsolved questions remain about the chemical identity of the final products, their deposition kinetics and their binding mechanism. In particular, the dopamine oxidation reaction kinetics is a key to improving surface modification efficiency. Here, we demonstrate that high O(2) concentrations in the dopamine solution lead to highly homogeneous, thin layer deposition on any material surfaces via accelerated reaction kinetics, elucidated by Le Chatelier's principle toward dopamine oxidation steps in a Michael-addition reaction. As a result, highly uniform, ultra-smooth modified surfaces are achieved in much shorter deposition times. This finding provides new insights into the effect of reaction kinetics and molecular geometry on the uniformity of modifications for surface engineering techniques.

  14. Achieving High Performance in AC-Field Driven Organic Light Sources

    PubMed Central

    Xu, Junwei; Carroll, David L.; Smith, Gregory M.; Dun, Chaochao; Cui, Yue

    2016-01-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m2 with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today’s OLEDs in performance. PMID:27063414

  15. Achieving High Performance in AC-Field Driven Organic Light Sources

    NASA Astrophysics Data System (ADS)

    Xu, Junwei; Carroll, David L.; Smith, Gregory M.; Dun, Chaochao; Cui, Yue

    2016-04-01

    Charge balance in organic light emitting structures is essential to simultaneously achieving high brightness and high efficiency. In DC-driven organic light emitting devices (OLEDs), this is relatively straight forward. However, in the newly emerging, capacitive, field-activated AC-driven organic devices, charge balance can be a challenge. In this work we introduce the concept of gating the compensation charge in AC-driven organic devices and demonstrate that this can result in exceptional increases in device performance. To do this we replace the insulator layer in a typical field-activated organic light emitting device with a nanostructured, wide band gap semiconductor layer. This layer acts as a gate between the emitter layer and the voltage contact. Time resolved device characterization shows that, at high-frequencies (over 40 kHz), the semiconductor layer allows for charge accumulation in the forward bias, light generating part of the AC cycle and charge compensation in the negative, quiescent part of the AC cycle. Such gated AC organic devices can achieve a non-output coupled luminance of 25,900 cd/m2 with power efficiencies that exceed both the insulator-based AC devices and OLEDs using the same emitters. This work clearly demonstrates that by realizing balanced management of charge, AC-driven organic light emitting devices may well be able to rival today’s OLEDs in performance.

  16. Challenges to achievement of metal sustainability in our high-tech society.

    PubMed

    Izatt, Reed M; Izatt, Steven R; Bruening, Ronald L; Izatt, Neil E; Moyer, Bruce A

    2014-04-21

    Achievement of sustainability in metal life cycles from mining of virgin ore to consumer and industrial devices to end-of-life products requires greatly increased recycling rates and improved processing of metals using conventional and green chemistry technologies. Electronic and other high-tech products containing precious, toxic, and specialty metals usually have short lifetimes and low recycling rates. Products containing these metals generally are incinerated, discarded as waste in landfills, or dismantled in informal recycling using crude and environmentally irresponsible procedures. Low recycling rates of metals coupled with increasing demand for high-tech products containing them necessitate increased mining with attendant environmental, health, energy, water, and carbon-footprint consequences. In this tutorial review, challenges to achieving metal sustainability, including projected use of urban mining, in present high-tech society are presented; health, environmental, and economic incentives for various government, industry, and public stakeholders to improve metal sustainability are discussed; a case for technical improvements, including use of molecular recognition, in selective metal separation technology, especially for metal recovery from dilute feed stocks is given; and global consequences of continuing on the present path are examined.

  17. Investigation of a nanofabrication process to achieve high aspect-ratio nanostructures on a quartz substrate.

    PubMed

    Mohamed, K; Alkaisi, M M

    2013-01-11

    This work investigates the development of a nanofabrication process to achieve high aspect-ratio nanostructures on quartz substrates using electron beam lithography (EBL) patterning and fluorinated plasma etching processes. An imaging layer of a poly(methyl methacrylate) bi-layer resist was spun coated on quartz substrate and exposed by an e-beam with the designed patterns of sub-100 nm feature sizes using a Raith-150 EBL patterning tool. Additive pattern transfer was employed by depositing a 40 nm thick Nichrome layer on the resist pattern using a metal evaporator which was later lifted off by soaking in acetone. Nichrome was employed as an etch mask and an Oxford Plasmalab 80Plus reactive ion etcher was used for the etching process. The etching process was carried out in a gas mixture of CHF(3)/Ar with a flow rate ratio of 50/30 sccm, pressure of 20 mTorr, radiofrequency power of 200 W and at room temperature. These etching process parameters were found to achieve a 10 nm min(-1) etch rate and tall vertical side walls profile. An aspect-ratio of 10:1 was achieved on 60 nm feature size structures.

  18. Investigation of a nanofabrication process to achieve high aspect-ratio nanostructures on a quartz substrate

    NASA Astrophysics Data System (ADS)

    Mohamed, K.; Alkaisi, M. M.

    2013-01-01

    This work investigates the development of a nanofabrication process to achieve high aspect-ratio nanostructures on quartz substrates using electron beam lithography (EBL) patterning and fluorinated plasma etching processes. An imaging layer of a poly(methyl methacrylate) bi-layer resist was spun coated on quartz substrate and exposed by an e-beam with the designed patterns of sub-100 nm feature sizes using a Raith-150 EBL patterning tool. Additive pattern transfer was employed by depositing a 40 nm thick Nichrome layer on the resist pattern using a metal evaporator which was later lifted off by soaking in acetone. Nichrome was employed as an etch mask and an Oxford Plasmalab 80Plus reactive ion etcher was used for the etching process. The etching process was carried out in a gas mixture of CHF3/Ar with a flow rate ratio of 50/30 sccm, pressure of 20 mTorr, radiofrequency power of 200 W and at room temperature. These etching process parameters were found to achieve a 10 nm min-1 etch rate and tall vertical side walls profile. An aspect-ratio of 10:1 was achieved on 60 nm feature size structures.

  19. Subpixel shift with Fourier transform to achieve efficient and high-quality image interpolation

    NASA Astrophysics Data System (ADS)

    Chen, Qin-Sheng; Weinhous, Martin S.

    1999-05-01

    A new approach to image interpolation is proposed. Different from the conventional scheme, the interpolation of a digital image is achieved with a sub-unity coordinate shift technique. In the approach, the original image is first shifted by sub-unity distances matching the locations where the image values need to be restored. The original and the shifted images are then interspersed together, yielding an interpolated image. High quality sub-unity image shift which is crucial to the approach is accomplished by implementing the shift theorem of Fourier transformation. It is well known that under the Nyquist sampling criterion, the most accurate image interpolation can be achieved with the interpolating function (sinc function). A major drawback is its computation efficiency. The present approach can achieve an interpolation quality as good as that with the sinc function since the sub-unity shift in Fourier domain is equivalent to shifting the sinc function in spatial domain, while the efficiency, thanks to the fast Fourier transform, is very much improved. In comparison to the conventional interpolation techniques such as linear or cubic B-spline interpolation, the interpolation accuracy is significantly enhanced. In order to compensate for the under-sampling effects in the interpolation of 3D medical images owing to a larger inter-slice distance, proper window functions were recommended. The application of the approach to 2- and 3-D CT and MRI images produced satisfactory interpolation results.

  20. Cognitive abilities and motivational processes in high school students' science achievement and engagement

    NASA Astrophysics Data System (ADS)

    Lau, Shun

    The dissertation presents two analytic approaches, a variable-centered and person-centered approach, to investigating holistic patterns of the cognitive, motivational, and affective correlates of science achievement and engagement in a sample of 491 10th and 11th grade high-school students. Building on Snow's (1989) idea of two pathways to achievement outcomes, Study 1 adopted a variable-centered approach to examining how cognitive and motivational factors associated with the performance and commitment pathways, respectively, contributed to the prediction of achievement outcomes in science. Results of hierarchical regression analyses showed that (a) students' cognitive abilities were the strongest predictors of their performance in science as measured by standardized test scores; (b) motivational processes enhanced the predictive validity for science test scores and grades beyond the variance accounted for by ability and demography; (c) motivational processes were the strongest predictors of students' commitment to science in the form of situational engagement and anticipated choices of science-related college majors and careers; and (d) competence beliefs served as a point of contact between the performance and commitment pathways. These results are consistent with Snow's (1989) conjecture that both performance and commitment pathway-related factors are necessary for understanding the full range of person-level inputs to achievement outcomes. Study 2 adopted a person-centered approach to examining holistic organizations of psychological factors within individuals and their relations to science achievement and engagement. Four types of students characterized by unique configurations of cognitive, motivational, and affective attributes were identified in both the male and female subsamples using inverse factor analysis. Type membership was found to distinguish students in various indicators of science achievement and engagement. Two of the four types were also found

  1. A new high school science program and its effect on student achievement in mathematics and science

    NASA Astrophysics Data System (ADS)

    Goodman, Robert

    Student achievement in mathematics and science is a high educational priority worldwide. The American educational system is not meeting its objectives for these subjects: our students are performing below international standards. The problem is endemic, leading to the conclusion that it is structural. During the last seven years, I have led the creation and implementation of a program whose aim is to address this problem. The structure of this program stresses horizontal and vertical curriculum articulations in order to increase curriculum efficiency and meaningfulness to students. My first aim, in conducting this study, was to determine the program's effectiveness. Since this was a long term program created in a real world environment it would be difficult to use experimental or quasi-experimental analysis. However, I was able to develop a plausible argument for the effectiveness of the program by using two measures to create a baseline for student aptitude and three measures to determine student achievement. Together these showed that the school's students, while typical of those in New Jersey, achieved very positive results in mathematic and science. The likelihood that the new program was responsible for this was enhanced by the fact that the verbal and mathematical aptitudes of the students were comparable, but their achievement in areas outside mathematic and science were not exceptional. My second aim was to provide documentation so that the program could be replicated at other schools. This included the scope and sequence of the mathematics and science courses; the curricula of the physics courses; an explanation the pedagogical approach used in the physics courses, and sample chapters of a textbook being written to support the first year physic course. Whiles those documents supply a snapshot of the current state of the program; they are probably insufficient to replicate it. This would also require an understanding of the program's rationale. Towards this

  2. Mathematical and numerical models to achieve high speed with special-purpose parallel processors

    SciTech Connect

    Cheng, H.S.; Wulff, W.; Mallen, A.N.

    1986-07-01

    One simulation facility that has been developed is the BNL Plant Analyzer, currently set up for BWR plant simulations at up to seven times faster than real-time process speeds. The principal hardware components of the BNL Plant Analyzer are two units of special-purpose parallel processors, the AD10 of Applied Dynamics International and a PDP-11/34 host computer. The AD10 is specifically designed for time-critical system simulations, utilizing the modern parallel processing technology with pipeline architecture. The simulator employs advanced modeling techniques and efficient integration techniques in conjunction with the parallel processors to achieve high speed performance.

  3. High School Principal Instructional Leadership Behavior in High and Low Need and High and Low Achievement Schools

    ERIC Educational Resources Information Center

    Fulton, Theodore T.

    2009-01-01

    The purpose of this study was to investigate teacher perceptions of the ten specific principal instructional leadership behaviors of Hallinger's Principal Instructional Management Rating Scale as they relate to school need, school achievement, years of experience as a teacher, and years working with the current principal. This quantitative…

  4. Number Sense-Based Strategies Used by High-Achieving Sixth Grade Students Who Experienced Reform Textbooks

    ERIC Educational Resources Information Center

    Alsawaie, Othman N.

    2012-01-01

    The purpose of this study was to explore strategies used by high-achieving 6th grade students in the United Arab Emirates (UAE) to solve basic arithmetic problems involving number sense. The sample for the study consisted of 15 high-achieving boys and 15 high-achieving girls in grade 6 from 2 schools in the Emirate of Abu Dhabi, UAE. Data for the…

  5. Bioconversion of High Concentrations of Hydrogen Sulfide to Elemental Sulfur in Airlift Bioreactor

    PubMed Central

    Abdel-Monaem Zytoon, Mohamed; Ahmad AlZahrani, Abdulraheem; Hamed Noweir, Madbuli; Ahmed El-Marakby, Fadia

    2014-01-01

    Several bioreactor systems are used for biological treatment of hydrogen sulfide. Among these, airlift bioreactors are promising for the bioconversion of hydrogen sulfide into elemental sulfur. The performance of airlift bioreactors is not adequately understood, particularly when directly fed with hydrogen sulfide gas. The objective of this paper is to investigate the performance of an airlift bioreactor fed with high concentrations of H2S with special emphasis on the effect of pH in combination with other factors such as H2S loading rate, oxygen availability, and sulfide accumulation. H2S inlet concentrations between 1,008 ppm and 31,215 ppm were applied and elimination capacities up to 113 g H2S m−3 h−1 were achieved in the airlift bioreactor under investigation at a pH range 6.5–8.5. Acidic pH values reduced the elimination capacity. Elemental sulfur recovery up to 95% was achieved under oxygen limited conditions (DO < 0.2 mg/L) and at higher pH values. The sulfur oxidizing bacteria in the bioreactor tolerated accumulated dissolved sulfide concentrations >500 mg/L at pH values 8.0–8.5, and near 100% removal efficiency was achieved. Overall, the resident microorganisms in the studied airlift bioreactor favored pH values in the alkaline range. The bioreactor performance in terms of elimination capacity and sulfur recovery was better at pH range 8–8.5. PMID:25147857

  6. The Combined Effect of Teacher Effectiveness Characteristics on Value-Added Student Achievement in Junior High School Mathematics

    ERIC Educational Resources Information Center

    Wadleigh, Linda L.

    2013-01-01

    Student academic achievement in junior high mathematics is an ongoing mission for educational leaders. To achieve that undertaking, teacher effectiveness plays an important role. The purpose of this study was to examine the combined effects of teacher effectiveness on student achievement. The study was conducted in a suburban school district in…

  7. Achieving High Contrast for Exoplanet Imaging with a Kalman Filter and Stroke Minimization

    NASA Astrophysics Data System (ADS)

    Eldorado Riggs, A. J.; Groff, T. D.; Kasdin, N. J.; Carlotti, A.; Vanderbei, R. J.

    2014-01-01

    High contrast imaging requires focal plane wavefront control and estimation to correct aberrations in an optical system; non-common path errors prevent the use of conventional estimation with a separate wavefront sensor. The High Contrast Imaging Laboratory (HCIL) at Princeton has led the development of several techniques for focal plane wavefront control and estimation. In recent years, we developed a Kalman filter for optimal wavefront estimation. Our Kalman filter algorithm is an improvement upon DM Diversity, which requires at least two images pairs each iteration and does not utilize any prior knowledge of the system. The Kalman filter is a recursive estimator, meaning that it uses the data from prior estimates along with as few as one new image pairs per iteration to update the electric field estimate. Stroke minimization has proven to be a feasible controller for achieving high contrast. While similar to a variation of Electric Field Conjugation (EFC), stroke minimization achieves the same contrast with less stroke on the DMs. We recently utilized these algorithms to achieve high contrast for the first time in our experiment at the High Contrast Imaging Testbed (HCIT) at the Jet Propulsion Laboratory (JPL). Our HCIT experiment was also the first demonstration of symmetric dark hole correction in the image plane using two DMs--this is a major milestone for future space missions. Our ongoing work includes upgrading our optimal estimator to include an estimate of the incoherent light in the system, which allows for simultaneous estimation of the light from a planet along with starlight. The two-DM experiment at the HCIT utilized a shaped pupil coronagraph. Those tests utilized ripple style, free-standing masks etched out of silicon, but our current work is in designing 2-D optimized reflective shaped pupils. In particular, we have created several designs for the AFTA telescope, whose pupil presents major hurdles because of its atypical pupil obstructions. Our

  8. High-performance partially aligned semiconductive single-walled carbon nanotube transistors achieved with a parallel technique.

    PubMed

    Wang, Yilei; Pillai, Suresh Kumar Raman; Chan-Park, Mary B

    2013-09-09

    Single-walled carbon nanotubes (SWNTs) are widely thought to be a strong contender for next-generation printed electronic transistor materials. However, large-scale solution-based parallel assembly of SWNTs to obtain high-performance transistor devices is challenging. SWNTs have anisotropic properties and, although partial alignment of the nanotubes has been theoretically predicted to achieve optimum transistor device performance, thus far no parallel solution-based technique can achieve this. Herein a novel solution-based technique, the immersion-cum-shake method, is reported to achieve partially aligned SWNT networks using semiconductive (99% enriched) SWNTs (s-SWNTs). By immersing an aminosilane-treated wafer into a solution of nanotubes placed on a rotary shaker, the repetitive flow of the nanotube solution over the wafer surface during the deposition process orients the nanotubes toward the fluid flow direction. By adjusting the nanotube concentration in the solution, the nanotube density of the partially aligned network can be controlled; linear densities ranging from 5 to 45 SWNTs/μm are observed. Through control of the linear SWNT density and channel length, the optimum SWNT-based field-effect transistor devices achieve outstanding performance metrics (with an on/off ratio of ~3.2 × 10(4) and mobility 46.5 cm(2) /Vs). Atomic force microscopy shows that the partial alignment is uniform over an area of 20 × 20 mm(2) and confirms that the orientation of the nanotubes is mostly along the fluid flow direction, with a narrow orientation scatter characterized by a full width at half maximum (FWHM) of <15° for all but the densest film, which is 35°. This parallel process is large-scale applicable and exploits the anisotropic properties of the SWNTs, presenting a viable path forward for industrial adoption of SWNTs in printed, flexible, and large-area electronics.

  9. Liquid high concentration IgG1 antibody formulations by precipitation.

    PubMed

    Matheus, Susanne; Friess, Wolfgang; Schwartz, Daniel; Mahler, Hanns-Christian

    2009-09-01

    A manufacturing approach for liquid high concentration antibody formulations based on precipitation and subsequent re-dissolution was investigated. IgG1 antibody solutions were concentrated from 20 to 100 mg/mL by intermediate precipitation, with a recovery exceeding 95%, retention of the native secondary structure and binding activity as well as adequate stability. Quantitative, reproducible precipitation was performed using 1.45 M ammonium sulphate (pH 5.5 and 8.0), 0.67 M sodium citrate (pH 8.0) and 9% (w/v) PEG 4000 (pH 5.5 and 8.0). Scalability was confirmed from 1 to 100 mL. The concentrations achievable in the re-dissolution step were less affected by the re-dissolution medium, but limited by the residual precipitant. Both, improved removal of remaining precipitant liquid and larger precipitation scales were successful in increasing the final protein concentration. SEC and turbidity analysis directly after re-dissolution indicated that similar protein qualities were obtained, independent from the precipitant used. However, increased aggregate formation was observed after short term storage of the precipitated protein particles at either 2-8 degrees C or ambient temperature. An accelerated mechanical and thermal stability program verified comparable stability of the re-dissolved liquid 100 mg/mL formulations produced by intermediate precipitation to a control formulation obtained by standard ultrafiltration.

  10. Carbon dioxide concentrations are very high in developing oilseeds.

    PubMed

    Goffman, Fernando D; Ruckle, Mike; Ohlrogge, John; Shachar-Hill, Yair

    2004-09-01

    A new method has been developed to rapidly determine the total inorganic carbon concentration (gaseous [CO2] + aqueous [CO(2)] + [HCO3-] + [CO3(2)-]) in developing seeds. Seeds are rapidly dissected and homogenized in 1 N HCl in gas-tight vials. The headspace gas is then analyzed by infrared gas analysis. Developing rapeseed (Brassica napus L.) and soybean [Glycine max (L.) Merr.] seeds were analyzed and found to have up to 40 and 12 mM total inorganic carbon, respectively. These concentrations are ca. 600-2000-fold higher than in ambient air or values reported for leaves. Carbon dioxide concentrations in rapeseed peaked during the stage of maximum oil synthesis and declined as seeds matured. The consequences for seed metabolism, physiology and carbon economy are discussed.

  11. Methods and devices for high-throughput dielectrophoretic concentration

    DOEpatents

    Simmons, Blake A.; Cummings, Eric B.; Fiechtner, Gregory J.; Fintschenko, Yolanda; McGraw, Gregory J.; Salmi, Allen

    2010-02-23

    Disclosed herein are methods and devices for assaying and concentrating analytes in a fluid sample using dielectrophoresis. As disclosed, the methods and devices utilize substrates having a plurality of pores through which analytes can be selectively prevented from passing, or inhibited, on application of an appropriate electric field waveform. The pores of the substrate produce nonuniform electric field having local extrema located near the pores. These nonuniform fields drive dielectrophoresis, which produces the inhibition. Arrangements of electrodes and porous substrates support continuous, bulk, multi-dimensional, and staged selective concentration.

  12. The Pentagon-S process: A systematic approach for achieving high confidence in high-consequence products

    SciTech Connect

    D`Antonio, P.E.; Covan, J.M.; Ekman, M.E.

    1997-10-01

    Sandia National Laboratories has developed a systematic approach for achieving high confidence in major products requiring high reliability for use in high-consequence applications. A high-consequence application is one in which product failure could result in significant loss of life, damage to major systems or to the environment, financial loss, or political repercussions. The application of this process has proven to be of significant benefit in the early identification, verification, and correction of potential product design and manufacturing process failure modes. Early identification and correction of these failures modes and the corresponding controls placed on safety-critical features, ensures product adherence to safety-critical design requirements, and enhances product quality, reliability, and the cost effectiveness of delivered products. Safety-critical features include design features such as materials and dimensions, as well as manufacturing features such as assembly processes, inspections, and testing.

  13. Generation of high-titer viral preparations by concentration using successive rounds of ultracentrifugation

    PubMed Central

    2011-01-01

    Background Viral vectors provide a method of stably introducing exogenous DNA into cells that are not easily transfectable allowing for the ectopic expression or silencing of genes for therapeutic or experimental purposes. However, some cell types, in particular bone marrow cells, dendritic cells and neurons are difficult to transduce with viral vectors. Successful transduction of such cells requires preparation of highly concentrated viral stocks, which permit a high virus concentration and multiplicity of infection (MOI) during transduction. Pseudotyping with the vesicular stomatitis virus G (VSV-G) envelope protein is common practice for both lentiviral and retroviral vectors. The VSV-G glycoprotein adds physical stability to retroviral particles, allowing concentration of virus by high-speed ultracentrifugation. Here we describe a method report for concentration of virus from large volumes of culture supernatant by means of successive rounds of ultracentrifugation into the same ultracentrifuge tube. Method Stable retrovirus producer cell lines were generated and large volumes of virus-containing supernatant were produced. We then tested the transduction ability of virus following varying rounds of concentration by ultra-centrifugation. In a second series of experiments lentivirus-containing supernatant was produced by transient transfection of 297T/17 cells and again we tested the transduction ability of virus following multiple rounds of ultra-centrifugation. Results We report being able to centrifuge VSV-G coated retrovirus for as many as four rounds of ultracentrifugation while observing an additive increase in viral titer. Even after four rounds of ultracentrifugation we did not reach a plateau in viral titer relative to viral supernatant concentrated to indicate that we had reached the maximum tolerated centrifugation time, implying that it may be possible to centrifuge VSV-G coated retrovirus even further should it be necessary to achieve yet higher

  14. What makes a good program? A case study of a school admitting high academic achievers.

    PubMed

    Lam, Ching Man

    2008-10-10

    This paper reports the results of a qualitative study that explored the administration and implementation of the Tier 1 Program (Secondary 1 Curriculum) of the Project P.A.T.H.S. The case study method was used to explore perceptions of the teachers and the project coordinator of program effectiveness, and to identify various factors for program success. A school admitting high academic achievers was selected, and site visits, as well as individual and focus group interviews, were conducted with the program coordinator, social worker, and course teachers. The results suggested that clear vision and program goals, high quality of curriculum, helpful leadership, positive teacher attitude, and strong administrative support are factors for program success. Analyzing the data enables the researchers to understand the characteristics of a successful program as well as the interplay among factors for producing success.

  15. Improving production of 11C to achieve high specific labelled radiopharmaceuticals

    NASA Astrophysics Data System (ADS)

    Savio, E.; García, O.; Trindade, V.; Buccino, P.; Giglio, J.; Balter, H.; Engler, H.

    2012-12-01

    Molecular imaging is usually based on the recognition by the radiopharmaceuticals of specific sites which are present in limited number or density in the cells or biological tissues. Thus is of high importance to label the radiopharmaceuticals with high specific activity to be able to achieve a high target to non target ratio. The presence of carbon dioxide (CO2) from the air containing 98,88% of 12C and 1,12% 13C compete with 11CO2 produced at the cyclotron. In order to minimize the presence of these isotopes along the process of irradiation, transferring and synthesis of radiopharmaceuticals labelled with 11C, we applied this method: previous to the irradiation the target was 3-4 times flushed with He (5.7) as a cold cleaning, followed by a similar conditioning of the line, from the target up to the module, and finally a hot cleaning in order to desorb 12CO2 and 13CO2, this was performed by irradiation during 1 min at 5 uA (3 times). In addition, with the aim of improving quality of gases in the target and in the modules, water traps (Agilent) were incorporated in the inlet lines of the target and modules. Target conditioning process (cold and hot flushings) as well as line cleaning, allowing the desorption of unlabelled CO2, together with the increasing of gas purity in the irradiation and in the synthesis, were critical parameters that enable to achieve 11C-radiopharamaceuticals with high specific activity, mainly in the case of 11C-PIB.

  16. A high temperature hybrid photovoltaic-thermal receiver employing spectral beam splitting for linear solar concentrators

    NASA Astrophysics Data System (ADS)

    Mojiri, Ahmad; Stanley, Cameron; Rosengarten, Gary

    2015-09-01

    Hybrid photovoltaic/thermal (PV-T) solar collectors are capable of delivering heat and electricity concurrently. Implementing such receivers in linear concentrators for high temperature applications need special considerations such as thermal decoupling of the photovoltaic (pv) cells from the thermal receiver. Spectral beam splitting of concentrated light provides an option for achieving this purpose. In this paper we introduce a relatively simple hybrid receiver configuration that spectrally splits the light between a high temperature thermal fluid and silicon pv cells using volumetric light filtering by semi-conductor doped glass and propylene glycol. We analysed the optical performance of this device theoretically using ray tracing and experimentally through the construction and testing of a full scale prototype. The receiver was mounted on a commercial parabolic trough concentrator in an outdoor experiment. The prototype receiver delivered heat and electricity at total thermal efficiency of 44% and electrical efficiency of 3.9% measured relative to the total beam energy incident on the primary mirror.

  17. [Partial nitrification of digested sludge liquor with low C/N and high-concentration ammonia].

    PubMed

    Zhang, Shu-Jun; Ma, Fu-Guo; Cao, Xiang-Sheng; Gan, Yi-Ping; Meng, Xue-Zheng; Zhou, Jun; Wang, Hong-Chen; Peng, Yong-Zhen

    2009-06-15

    The experimental system consisted of anoxic filter and aerobic suspended carrier biofilm reactor. The partial nitrification was achieved and maintained stably in the aerobic reactor under normal temperature (15-29 degrees C) and high DO (6-9 mg/L). The nitritation with 70%-80% nitrite accumulation efficiency was obtained when FA concentration was in the range of 1.0-10.3 mg/L by controlling influent ammonia loading rate (ALR), ratio of alkalinity and ammonia and HRT in the aerobic reactor. The effluent nitrite/ammonia ratio was about 1.25 when the average influent ammonia, influent ALR and influent ratio of alkalinity and ammonia were 315.80 mg/L, 0.43 kg/(m3 x d) and 5.25, respectively. So the effluent of partial nitrification process provided the influent substrate demand for the following ANAMMOX process. The integrative analysis indicated that the proper FA concentration was the main factor achieving the partial nitrification. The study developed a novel partial nitrification technology adapt to water characteristics of digested sludge liquor.

  18. A highly concentrated diet increases biogas production and the agronomic value of young bull's manure.

    PubMed

    Mendonça Costa, Mônica Sarolli Silva de; Lucas, Jorge de; Mendonça Costa, Luiz Antonio de; Orrico, Ana Carolina Amorim

    2016-02-01

    The increasing demand for animal protein has driven significant changes in cattle breeding systems, mainly in feedlots, with the use of young bulls fed on diets richer in concentrate (C) than in forage (F). These changes are likely to affect animal manure, demanding re-evaluation of the biogas production per kg of TS and VS added, as well as of its agronomic value as a biofertilizer, after anaerobic digestion. Here, we determined the biogas production and agronomic value (i.e., the macronutrient concentration in the final biofertilizer) of the manure of young bulls fed on diets with more (80% C+20% F; 'HighC' diet) or less (65% C+35% F; 'LowC' diet) concentrate, evaluating the effects of temperature (25, 35, and 40°C) and the use of an inoculum, during anaerobic digestion. A total of 24 benchtop reactors were used, operating in a semi-continuous system, with a 40-day hydraulic retention time (HRT). The manure from animals given the HighC diet had the greatest potential for biogas production, when digested with the use of an inoculum and at 35 or 40°C (0.6326 and 0.6207m(3)biogas/kg volatile solids, or VS, respectively). We observed the highest levels of the macronutrients N, P, and K in the biofertilizer from the manure of animals given HighC. Our results show that the manure of young bulls achieves its highest potential for biogas production and agronomic value when animals are fed diets richer in concentrate, and that biogas production increases if digestion is performed at higher temperatures, and with the use of an inoculum.

  19. Fabricating high-concentration GaAs cell photovoltaic modules

    SciTech Connect

    Kaminar, N.R.; Hamaker, H.C.

    1986-04-01

    This program comprises the design and manufacture of components of a GaAs-cell, passively-cooled concentrator. A Fresnel lens, 5.44-inches square, was used in conjunction with a solid glass, domed-top secondary optical element to concentrate the light on single-junction GaAs cells. The cell had an active area 0.2 inches in diameter and was soldered directly to the copper heatspreader. The heatspreader was bonded with heat-conductive RTV to an aluminum dissipator, which formed the module housing. The module was designed to be attached to a tracker at the center. Obtained were 26% cell efficiency in flash tests and 19.2% combined lens/cell efficiency outdoors. Optical transmission was lower than expected due to higher than expected losses in the secondary. The secondaries were made using a molding technique applicable to mass production.

  20. Dimerization in Highly Concentrated Solutions of Phosphoimidazolide Activated Monomucleotides

    NASA Astrophysics Data System (ADS)

    Kanavarioti, Anastassia

    1997-08-01

    Phosphoimidazolide activated ribomononucleotides (*pN) are useful substrates for the non-enzymatic synthesis of polynucleotides. However, dilute neutral aqueous solutions of *pN typically yield small amounts of dimers and traces of polymers; most of *pN hydrolyzes to yield nucleoside 5'-monophosphate. Here we report the self-condensation of nucleoside 5'-phosphate 2-methylimidazolide (2-MeImpN with N = cytidine, uridine or guanosine) in the presence of Mg2+ in concentrated solutions, such as might have been found in an evaporating lagoon on prebiotic Earth. The product distribution indicates that oligomerization is favored at the expense of hydrolysis. At 1.0 M, 2-MeImpU and 2-MeImpC produce about 65% of oligomers including 4% of the 3',5'-linked dimer. Examination of the product distribution of the three isomeric dimers in a self-condensation allows identification of reaction pathways that lead to dimer formation. Condensations in a concentrated mixture of all three nucleotides (U,C,G mixtures) is made possible by the enhanced solubility of 2-MeImpG in such mixtures. Although percent yield of internucleotide linked dimers is enhanced as a function of initial monomer concentration, pyrophosphate dimer yields remain practically unchanged at about 20% for 2-MeImpU, 16% for 2-MeImpC and 25% of the total pyrophosphate in the U,C,G mixtures. The efficiency by which oligomers are produced in these concentrated solutions makes the evaporating lagoon scenario a potentially interesting medium for the prebiotic synthesis of dimers and short RNAs.

  1. Asymptotic Expansion in Enzyme Reactions with High Enzyme Concentrations

    NASA Astrophysics Data System (ADS)

    Bersani, Alberto Maria; Dell'Acqua, Guido

    2010-09-01

    In this paper we find a new asymptotic expansion valid in enzymatic reactions where the total amount of enzyme exceeds greatly the total amount of substrate. In such case it is well known that the Michelis-Menten approximation is no longer valid; therefore our asymptotic expansion is a new tool to approximate in a closed form the concentrations of the reactants in presence of an enzyme excess.

  2. Dimerization in Highly Concentrated Solutions of Phosphoimidazolide Activated Mononucleotides

    NASA Technical Reports Server (NTRS)

    Kanavarioti, Anastassia

    1997-01-01

    Phosphoimidazolide activated ribomononucleotides (*pN) are useful substrates for the non-enzymatic synthesis of polynucleotides. However, dilute neutral aqueous solutions of *pN typically yield small amounts of dimers and traces of polymers; most of *pN hydrolyzes to yield nucleoside 5'-monophosphate. Here we report the self-condensation of nucleoside 5'-phosphate 2- methylimidazolide (2-MeImpN with N = cytidine, uridine or guanosine) in the presence of Mg2(+) in concentrated solutions, such as might have been found in an evaporating lagoon on prebiotic Earth. The product distribution indicates that oligomerization is favored at the expense of hydrolysis. At 1.0 M, 2-MelmpU and 2-MelmpC produce about 65% of oligomers including 4% of the 3',5'-Iinked dimer. Examination of the product distribution of the three isomeric dimers in a self-condensation allows identification of reaction pathways that lead to dimer formation. Condensations in a concentrated mixture of all three nucleotides (U,C,G mixtures) is made possible by the enhanced solubility of 2-MeImpG in such mixtures. Although percent yield of intemucleotide linked dimers is enhanced as a function of initial monomer concentration, pyrophosphate dimer yields remain practically unchanged at about 20% for 2-MelmpU, 16% for 2-MeImpC and 25% of the total pyrophosphate in the U,C,G mixtures. The efficiency by which oligomers are produced in these concentrated solutions makes the evaporating lagoon scenario a potentially interesting medium for the prebiotic synthesis of dimers and short RNAs.

  3. Does a high concentration of calcium in the urine cause an important renal concentrating defect in human subjects?

    PubMed

    Lam, G S; Asplin, J R; Halperin, M L

    2000-03-01

    The objective of this study was to evaluate the hypothesis that a high concentration of ionized calcium in the lumen of the medullary collecting duct causes an osmole-free water diuresis. The urine flow rate and osmolality were measured in normal human subjects, as well as in patients with a history of nephrolithiasis who excreted more than 5 mmol of calcium per 24 h. There was an inverse relationship between the concentration of calcium in the urine and the 24 h urine volume both in normal subjects and in patients with a history of nephrolithiasis. When the concentration of calcium in the urine was greater than 5 mmol/l, the urine volume was less than 1 litre per day in the majority of subjects. After 16 h of water deprivation, when the concentration of calcium in the urine was as high as 17 mmol/l (ionized calcium 7.4 mmol/l), urine osmolality was 1258 mOsm/kg of water and the urine flow rate was 0.30 ml/min. We conclude that, although a calcium receptor may be present in the lumen of the medullary collecting duct in human subjects, an extremely high concentration of urinary total and ionized calcium does not cause a clinically important defect in the renal concentrating process.

  4. High school students' perceptions of EFL teacher control orientations and their English academic achievement.

    PubMed

    Kiany, Gholam Reza; Shayestefar, Parvaneh

    2011-09-01

    BACKGROUND. Theories distinguish between student-initiated and teacher-initiated regulation of students' learning activities, or between strong, shared, or loose teacher control during the completion of learning tasks. Empirical validations for such distinctions are scarce, however. AIM. The present study aimed at (a) investigating students' perceptions of control behaviours exhibited by their English teachers; and (b) exploring the contribution of different types of teacher control behaviours to students' cognitive outcomes (English Achievement). SAMPLE. The sample comprised 732 English as a Foreign Language (EFL) students studying in three major fields of high school (Mathematics, Natural Science, and Humanities). The participants (16-17 years of age) were selected from third-grade classes of 27 EFL teachers working in 25 high schools of 6 main different geographical regions in the Isfahan province, Iran. METHOD. To obtain a comprehensive picture of different control types exhibited by Iranian EFL teachers, the control subscales of the two existing questionnaires, i.e., the Questionnaire on Instructional Behaviours (QIB), adapted by Den Brok et al. (2004) and the Questionnaire on Lesson Activities (QLA) used by Den Brok (2001) were merged to form the Questionnaire of Teacher Control (QTC). The development of this Persian instrument involved several steps: translation and back translation by the researchers, one expert translator, and two EFL teachers; piloting; and a final administration of the questionnaire to the student sample. With respect to the second aim of the study, data regarding students' performances on the Standardized National English Achievement Tests were gathered from local educational offices and schools. RESULTS AND CONCLUSION. Statistical analyses supported acceptable reliability and validity of the instrument. A main factor structure with three types of teacher control (strong/high, shared/mid, and loose/low) was found to underlie students

  5. Not choosing nursing: work experience and career choice of high academic achieving school leavers.

    PubMed

    Neilson, Gavin R; McNally, James G

    2010-01-01

    Work experience has been a feature of the secondary school curriculum in the United Kingdom for a number of years. Usually requested by the pupil, it aims to provide opportunities for school pupils to enhance their knowledge and understanding of an occupation. The main benefits are claimed to be that it can help pupils develop an insight into the skills and attitudes required for an occupation and an awareness of career opportunities. However the quality and choice of placements are considered to be of great importance in this process and in influencing career choice [Department for Education and Skills (DfES), 2002a. Work Experience: A Guide for Employers. Department for Education and Skills, London]. As university departments of nursing experience a decline in the number of school pupils entering student nurse education programmes, and with the competition for school leavers becoming even greater, it is important to consider whether school pupils have access to appropriate work placements in nursing and what influence their experience has on pursuing nursing as a career choice. This paper is based on interview data from 20 high academic achieving fifth and sixth year school pupils in Scotland, paradigmatic cases from a larger survey sample (n=1062), who had considered nursing as a possible career choice within their career preference cluster, but then later disregarded nursing and decided to pursue medicine or another health care profession. This was partly reported by Neilson and Lauder [Neilson, G.R., Lauder, W., 2008. What do high academic achieving school pupils really think about a career in nursing: analysis of the narrative from paradigmatic case interviews. Nurse Education Today 28(6), 680-690] which examined what high academic achieving school pupils really thought about a career in nursing. However, the data was particularly striking in revealing the poor quality of nursing work experience for the pupils, and also their proposal that there was a need

  6. Tuning charge balance in PHOLEDs with ambipolar host materials to achieve high efficiency

    SciTech Connect

    Padmaperuma, Asanga B.; Koech, Phillip K.; Cosimbescu, Lelia; Polikarpov, Evgueni; Swensen, James S.; Chopra, Neetu; So, Franky; Sapochak, Linda S.; Gaspar, Daniel J.

    2009-08-27

    The efficiency and stability of blue organic light emitting devices (OLEDs) continue to be a primary roadblock to developing organic solid state white lighting. For OLEDs to meet the high power conversion efficiency goal, they will require both close to 100% internal quantum efficiency and low operating voltage in a white light emitting device.1 It is generally accepted that such high quantum efficiency, can only be achieved with the use of organometallic phosphor doped OLEDs. Blue OLEDs are particularly important for solid state lighting. The simplest (and therefore likely the lowest cost) method of generating white light is to down convert part of the emission from a blue light source with a system of external phosphors.2 A second method of generating white light requires the superposition of the light from red, green and blue OLEDs in the correct ratio. Either of these two methods (and indeed any method of generating white light with a high color rendering index) critically depends on a high efficiency blue light component.3 A simple OLED generally consists of a hole-injecting anode, a preferentially hole transporting organic layer (HTL), an emissive layer that contains the recombination zone and ideally transports both holes and electrons, a preferentially electron-transporting layer (ETL) and an electron-injecting cathode. Color in state-of-the-art OLEDs is generated by an organometallic phosphor incorporated by co-sublimation into the emissive layer (EML).4 New materials functioning as hosts, emitters, charge transporting, and charge blocking layers have been developed along with device architectures leading to electrophosphorescent based OLEDs with high quantum efficiencies near the theoretical limit. However, the layers added to the device architecture to enable high quantum efficiencies lead to higher operating voltages and correspondingly lower power efficiencies. Achievement of target luminance power efficiencies will require new strategies for lowering

  7. High and Low Reading Comprehension Achievers' Strategic Behaviors and Their Relation to Performance in a Reading Comprehension Situation

    ERIC Educational Resources Information Center

    Dermitzaki, Irini; Andreou, Georgia; Paraskeva, Violetta

    2008-01-01

    This study aimed at investigating the actual strategic behaviors of high and low achievers in reading comprehension and their relation with respective performance. The participants were 45 individually examined third graders, 20 high and 25 low reading comprehension achievers. Cognitive, metacognitive, and motivational aspects of the participants'…

  8. A Comparison of Strategic Development for Multiplication Problem Solving in Low-, Average-, and High-Achieving Students

    ERIC Educational Resources Information Center

    Zhang, Dake; Ding, Yi; Barrett, Dave E.; Xin, Yan Ping; Liu, Ru-de

    2014-01-01

    The present study investigated the differences of strategy use between low-, average-, and high-achieving students when solving different multiplication problems. Nineteen high-, 48 average-, and 17 low-achieving students participated in this study. All participants were asked to complete three different multiplication tests and to explain how…

  9. Is Early Ability Grouping Good for High-Achieving Students' Psychosocial Development? Effects of the Transition into Academically Selective Schools

    ERIC Educational Resources Information Center

    Becker, Michael; Neumann, Marko; Tetzner, Julia; Böse, Susanne; Knoppick, Henrike; Maaz, Kai; Baumert, Jürgen; Lehmann, Rainer

    2014-01-01

    The present study investigates school context effects on psychosocial characteristics (academic self-concept, peer relations, school satisfaction, and school anxiety) of high-achieving and gifted students. Students who did or did not make an early transition from elementary to secondary schools for high-achieving and gifted students in 5th grade…

  10. The Difference in the Academic Achievement of Hispanic High School Students Based on the Theme of the Small Learning Community

    ERIC Educational Resources Information Center

    Martinez, Beate M. Winter

    2010-01-01

    The purpose of this study is to describe the difference in the academic achievement of urban Hispanic high school students based on the small learning community theme. The study used a quantitative method of ex post facto research to examine how the academic achievement of Hispanic high school students differs across the themes of small…

  11. Trajectories of Chinese Students' Sense of School Belonging and Academic Achievement over the High School Transition Period

    ERIC Educational Resources Information Center

    Liu, Yangyang; Lu, Zuhong

    2011-01-01

    The present study identified the different patterns of Chinese students' academic achievement trajectories over the high school transition period and examined the relationships between students' sense of school belonging trajectories and the different patterns of academic achievement trajectories. In a sample of 567 Chinese high school students, a…

  12. Robust and Fragile Mathematical Identities: A Framework for Exploring Racialized Experiences and High Achievement among Black College Students

    ERIC Educational Resources Information Center

    McGee, Ebony O.

    2015-01-01

    I introduce the construct of fragile and robust identities for the purpose of exploring the experiences that influenced the mathematical and racial identities of high-achieving Black college students in mathematics and engineering. These students maintained high levels of academic achievement in these fields while enduring marginalization,…

  13. Theoretical Study of Monolayer and Double-Layer Waveguide Love Wave Sensors for Achieving High Sensitivity.

    PubMed

    Li, Shuangming; Wan, Ying; Fan, Chunhai; Su, Yan

    2017-03-22

    Love wave sensors have been widely used for sensing applications. In this work, we introduce the theoretical analysis of the monolayer and double-layer waveguide Love wave sensors. The velocity, particle displacement and energy distribution of Love waves were analyzed. Using the variations of the energy repartition, the sensitivity coefficients of Love wave sensors were calculated. To achieve a higher sensitivity coefficient, a thin gold layer was added as the second waveguide on top of the silicon dioxide (SiO₂) waveguide-based, 36 degree-rotated, Y-cut, X-propagating lithium tantalate (36° YX LiTaO₃) Love wave sensor. The Love wave velocity was significantly reduced by the added gold layer, and the flow of wave energy into the waveguide layer from the substrate was enhanced. By using the double-layer structure, almost a 72-fold enhancement in the sensitivity coefficient was achieved compared to the monolayer structure. Additionally, the thickness of the SiO₂ layer was also reduced with the application of the gold layer, resulting in easier device fabrication. This study allows for the possibility of designing and realizing robust Love wave sensors with high sensitivity and a low limit of detection.

  14. Theoretical Study of Monolayer and Double-Layer Waveguide Love Wave Sensors for Achieving High Sensitivity

    PubMed Central

    Li, Shuangming; Wan, Ying; Fan, Chunhai; Su, Yan

    2017-01-01

    Love wave sensors have been widely used for sensing applications. In this work, we introduce the theoretical analysis of the monolayer and double-layer waveguide Love wave sensors. The velocity, particle displacement and energy distribution of Love waves were analyzed. Using the variations of the energy repartition, the sensitivity coefficients of Love wave sensors were calculated. To achieve a higher sensitivity coefficient, a thin gold layer was added as the second waveguide on top of the silicon dioxide (SiO2) waveguide–based, 36 degree–rotated, Y-cut, X-propagating lithium tantalate (36° YX LiTaO3) Love wave sensor. The Love wave velocity was significantly reduced by the added gold layer, and the flow of wave energy into the waveguide layer from the substrate was enhanced. By using the double-layer structure, almost a 72-fold enhancement in the sensitivity coefficient was achieved compared to the monolayer structure. Additionally, the thickness of the SiO2 layer was also reduced with the application of the gold layer, resulting in easier device fabrication. This study allows for the possibility of designing and realizing robust Love wave sensors with high sensitivity and a low limit of detection. PMID:28327504

  15. Science literacy in high school students: A comparison of achievement in two curriculum approaches

    NASA Astrophysics Data System (ADS)

    McAlister, Diane C.

    2009-12-01

    Academic achievement as measured by the Florida Comprehensive Assessment Test (FCAT) in science for 367 students in two science curriculum options, integrated science and the traditional subject-specific courses, in one central Florida high school were compared. A multivariate analysis of covariance (MANCOVA) of science curriculum choice was analyzed for three variables, total FCAT score, earth science subscore, and scientific thinking subscore. Covariate of academic ability as defined by grade point average (GPA) and academic focus as defined by post secondary plans were considered for use. Analysis of statistically significant results was completed through analysis of covariance (ANCOVA). While statistically significant results were found in favor of the traditional curriculum group, additional statistical analysis of the curriculum groups for differences in socioeconomic status (SES), gender, and instructional level led to a logistic regression to explore the ability of these variables, GPA, and total FCAT score to predict curriculum group membership. GPA, level of instruction and FCAT score were found to be statistically significant predictors. Final conclusions to the study indicated a significant difference in scientific literacy for the two groups in favor of the traditional curriculum. However, logistic regression results indicated that due to significant differences in SES, gender, GPA, and level of instruction for the groups, the differences in academic achievement were probably due to factors other than curriculum design. Limitations of the study and suggestions for further research were presented.

  16. High-accuracy measurements of N2O concentration and site-specific nitrogen isotopes in small or high concentration samples

    NASA Astrophysics Data System (ADS)

    Palmer, M. R.; Arata, C.; Huang, K.

    2014-12-01

    Nitrous oxide (N2O) gas is among the major contributors to global warming and ozone depletion in stratosphere. Quantitative estimate of N­2O production in various pathways and N­2O fluxes across different reservoirs is the key to understanding the role of N­2O in the global change. To achieve this goal, accurate and concurrent measurement of both N2O concentration ([N2O]) and its site-specific isotopic composition (SP-δ15N), namely δ15Nα and δ15Nβ, is desired. Recent developments in Cavity Ring-Down Spectroscopy (CRDS) have enabled high precision measurements of [N2O] and SP-δ15N of a continuous gas flow. However, many N­­2O samples are discrete with limited volume (< 500 ml), and/or high [N2O] (> 2 ppm), and are not suitable for direct measurements by CRDS. Here we present results of a Small Sample Isotope Module 2 (SSIM2) which is coupled to and automatically coordinated with a Picarro isotopic N2O CRDS analyzer to handle and measure high concentration and/or small volume samples. The SSIM2 requires 20 ml of sample per analysis, and transfers the sample to the CRDS for high precision measurement. When the sample injection is < 20 ml, a zero gas is optionally filled to make up the volume. We used the SSIM2 to dilute high [N2O] samples and < 20 ml samples, and tested the effect of dilution on the measured SP-δ15N. In addition, we employed and tested a newly developed double injection method for samples adequate for two 20 ml injections. After the SSIM2 and the CRDS cavity was primed with the first injection, the second injection, which has negligible dilution of the sample, can be accurately measured for both [N2O] and SP-δ15N. Results of these experiments indicate that the precision of SSIM2-CRDS is similar to that of the continuous measurements using the CRDS alone, and that dilution has minimal effect on SP-δ15N, as along as the [N2O] is > 300 ppb after dilution. Overall, the precision of SP-δ15N measured using the SSIM2 is < 0.5 ‰.

  17. Achieving behavioral control with millisecond resolution in a high-level programming environment.

    PubMed

    Asaad, Wael F; Eskandar, Emad N

    2008-08-30

    The creation of psychophysical tasks for the behavioral neurosciences has generally relied upon low-level software running on a limited range of hardware. Despite the availability of software that allows the coding of behavioral tasks in high-level programming environments, many researchers are still reluctant to trust the temporal accuracy and resolution of programs running in such environments, especially when they run atop non-real-time operating systems. Thus, the creation of behavioral paradigms has been slowed by the intricacy of the coding required and their dissemination across labs has been hampered by the various types of hardware needed. However, we demonstrate here that, when proper measures are taken to handle the various sources of temporal error, accuracy can be achieved at the 1 ms time-scale that is relevant for the alignment of behavioral and neural events.

  18. The design and development of a high concentration and high efficiency photovoltaic concentrator utilizing a curved Fresnel lens

    SciTech Connect

    Moffat, A.L.; Scharlack, R.S.

    1982-09-01

    The design and development of an innovative photovoltaic concentrator which utilizes a low cost molded Fresnel lens is described. The lens design and fabrication are discussed, as well as the design of the collector module and tracking structure. A description of instrumentation developed to aid in the testing of lenses and solar cells is presented, and includes the test results.

  19. Strategies for achieving high-level expression of genes in Escherichia coli.

    PubMed Central

    Makrides, S C

    1996-01-01

    Progress in our understanding of several biological processes promises to broaden the usefulness of Escherichia coli as a tool for gene expression. There is an expanding choice of tightly regulated prokaryotic promoters suitable for achieving high-level gene expression. New host strains facilitate the formation of disulfide bonds in the reducing environment of the cytoplasm and offer higher protein yields by minimizing proteolytic degradation. Insights into the process of protein translocation across the bacterial membranes may eventually make it possible to achieve robust secretion of specific proteins into the culture medium. Studies involving molecular chaperones have shown that in specific cases, chaperones can be very effective for improved protein folding, solubility, and membrane transport. Negative results derived from such studies are also instructive in formulating different strategies. The remarkable increase in the availability of fusion partners offers a wide range of tools for improved protein folding, solubility, protection from proteases, yield, and secretion into the culture medium, as well as for detection and purification of recombinant proteins. Codon usage is known to present a potential impediment to high-level gene expression in E. coli. Although we still do not understand all the rules governing this phenomenon, it is apparent that "rare" codons, depending on their frequency and context, can have an adverse effect on protein levels. Usually, this problem can be alleviated by modification of the relevant codons or by coexpression of the cognate tRNA genes. Finally, the elucidation of specific determinants of protein degradation, a plethora of protease-deficient host strains, and methods to stabilize proteins afford new strategies to minimize proteolytic susceptibility of recombinant proteins in E. coli. PMID:8840785

  20. Excess Thermodynamic Properties of Concentrated Aqueous Solutions at High Temperatures

    SciTech Connect

    Guszkiewicz, M.S.

    2001-06-07

    Measurements of the vapor pressure of the solvent in wide ranges of concentration and temperature provide information on solute solvation and ion pairing--the two phenomena most often invoked for description of dilute solutions. Even in moderately concentrated solutions, as interionic distances become comparable to ionic diameters, these simple concepts gradually lose their meaning and solutions behave like molten salts. The usefulness of experimental vapor pressure results increases rapidly with their accuracy, since derived properties, such as solution enthalpies and heat capacities, can be calculated. Very accurate results can be obtained by the isopiestic method, but primary vapor pressure data for standard solutions are needed. In order to obtain vapor pressures at conditions where accurate isopiestic standards are not available and to establish more accurate standards, the ORNL isopiestic apparatus was modified for simultaneous direct vapor pressure measurements and isopiestic comparisons. There are no comprehensive solution theories derived from molecular level models and able to predict thermodynamic properties of various electrolytes as the composition changes from dilute solutions to molten salts in a wide range of temperatures. Empirical and semi-empirical models are useful for representation of experimental results, interpretation of measurements of other properties such as conductance., solubility or liquid-vapor partitioning of solutes, and for verification of theoretical predictions. Vapor pressures for aqueous CaCl{sub 2}, CaBr{sub 2}, LiCl, LiBr, LiI, NaI were measured at temperatures between 380 and 523 K in the concentration range extended to water activities below 0.2 (over 30 mol/kg for LiCl). General equations based on the modified Pitzer ion-interaction model were used to obtain enthalpy and heat capacity surfaces, which are compared with direct calorimetric measurements.

  1. Unexpectedly high indoor hydroxyl radical concentrations associated with nitrous acid.

    PubMed

    Gómez Alvarez, Elena; Amedro, Damien; Afif, Charbel; Gligorovski, Sasho; Schoemaecker, Coralie; Schoemacker, Coralie; Fittschen, Christa; Doussin, Jean-Francois; Wortham, Henri

    2013-08-13

    The hydroxyl (OH) radical is the most important oxidant in the atmosphere since it controls its self-oxidizing capacity. The main sources of OH radicals are the photolysis of ozone and the photolysis of nitrous acid (HONO). Due to the attenuation of solar radiation in the indoor environment, the possibility of OH formation through photolytic pathways indoors has been ignored up to now. In the indoor air, the ozonolysis of alkenes has been suggested as an alternative route of OH formation. Models and indirect measurements performed up to now according to this hypothesis suggest concentrations of OH radicals on the order of 10(4)-10(5) molecules per cubic centimeter. Here, we present direct measurements of significant amounts of OH radicals of up to 1.8⋅10(6) molecules per cubic centimeter during an experimental campaign carried out in a school classroom in Marseille. This concentration is on the same order of magnitude of outdoor OH levels in the urban scenario. We also show that photolysis of HONO is an important source of OH radicals indoors under certain conditions (i.e., direct solar irradiation inside the room). Additionally, the OH concentrations were found to follow a linear dependence with the product J(HONO)⋅[HONO]. This was also supported by using a simple quasiphotostationary state model on the OH radical budget. These findings force a change in our understanding of indoor air quality because the reactivity linked to OH would involve formation of secondary species through chemical reactions that are potentially more hazardous than the primary pollutants in the indoor air.

  2. Unexpectedly high indoor hydroxyl radical concentrations associated with nitrous acid

    PubMed Central

    Gómez Alvarez, Elena; Amedro, Damien; Afif, Charbel; Gligorovski, Sasho; Schoemaecker, Coralie; Fittschen, Christa; Doussin, Jean-Francois; Wortham, Henri

    2013-01-01

    The hydroxyl (OH) radical is the most important oxidant in the atmosphere since it controls its self-oxidizing capacity. The main sources of OH radicals are the photolysis of ozone and the photolysis of nitrous acid (HONO). Due to the attenuation of solar radiation in the indoor environment, the possibility of OH formation through photolytic pathways indoors has been ignored up to now. In the indoor air, the ozonolysis of alkenes has been suggested as an alternative route of OH formation. Models and indirect measurements performed up to now according to this hypothesis suggest concentrations of OH radicals on the order of 104–105 molecules per cubic centimeter. Here, we present direct measurements of significant amounts of OH radicals of up to 1.8⋅106 molecules per cubic centimeter during an experimental campaign carried out in a school classroom in Marseille. This concentration is on the same order of magnitude of outdoor OH levels in the urban scenario. We also show that photolysis of HONO is an important source of OH radicals indoors under certain conditions (i.e., direct solar irradiation inside the room). Additionally, the OH concentrations were found to follow a linear dependence with the product J(HONO)⋅[HONO]. This was also supported by using a simple quasiphotostationary state model on the OH radical budget. These findings force a change in our understanding of indoor air quality because the reactivity linked to OH would involve formation of secondary species through chemical reactions that are potentially more hazardous than the primary pollutants in the indoor air. PMID:23898188

  3. The anaesthesia of fish by high carbon-dioxide concentrations

    USGS Publications Warehouse

    1942-01-01

    A practical and economical method for anaesthetizing adult salmon and steelhead trout in the fish trucks used in the Grand Coulee fish salvage program is described. The method consists in generating a predetermined carbon-dioxide concentration in the 1000-gallon tanks of the trucks through the successive addition of predissolved sodium bicarbonate and dilute sulphuric acid in proper quantities. Carbon-dioxide anaesthesia effectively solved the acute problem of species segregation in the fish salvage program and, with minor modifications, could be used with equal success in certain hatchery operations necessitating the handling of large fish.

  4. New PSA high concentration solar furnace SF40

    NASA Astrophysics Data System (ADS)

    Rodriguez, Jose; Cañadas, Inmaculada; Zarza, Eduardo

    2016-05-01

    A new solar furnace has been designed and built at Plataforma Solar de Almería. In this work, its main components such as heliostat, concentrator, attenuator and test table, and the method used to align them are described. Other equipment like the auxiliary systems necessary for the solar operation, vacuum chamber and gas system are outlined too. Finally, the thermal characteristics of the focus were measured during a test campaign, where different planes along the optical axis were scanned with a radiometer, and the peak flux was obtained and is presented in the last section of this report.

  5. Reductions in ozone at high concentrations of stratospheric halogens

    NASA Technical Reports Server (NTRS)

    Prather, M. J.; Mcelroy, M. B.; Wofsy, S. C.

    1984-01-01

    An increase in the concentration of inorganic chlorine to levels comparable to that of oxidized reactive nitrogen could cause a significant change in the chemistry of the lower stratosphere leading to a reduction potentially larger than 15 percent in the column density of ozone. This could occur, for example by the middle of the next century, if emissions of man-made chlorocarbons were to grow at a rate of 3 percent per year. Ozone could be further depressed by release of industrial bromocarbon.

  6. Pulse number controlled laser annealing for GeSn on insulator structure with high substitutional Sn concentration

    NASA Astrophysics Data System (ADS)

    Moto, Kenta; Matsumura, Ryo; Sadoh, Taizoh; Ikenoue, Hiroshi; Miyao, Masanobu

    2016-06-01

    Crystalline GeSn-on-insulator structures with high Sn concentration (>8%), which exceeds thermal equilibrium solid-solubility (˜2%) of Sn in Ge, are essential to achieve high-speed thin film transistors and high-efficiency optical devices. We investigate non-thermal equilibrium growth of Ge1-xSnx (0 ≤ x ≤ 0.2) on quartz substrates by using pulsed laser annealing (PLA). The window of laser fluence enabling complete crystallization without film ablation is drastically expanded (˜5 times) by Sn doping above 5% into Ge. Substitutional Sn concentration in grown layers is found to be increased with decreasing irradiation pulse number. This phenomenon can be explained on the basis of significant thermal non-equilibrium growth achieved by higher cooling rate after PLA with a lower pulse number. As a result, GeSn crystals with substitutional Sn concentration of ˜12% are realized at pulse irradiation of single shot for the samples with the initial Sn concentration of 15%. Raman spectroscopy and electron microscopy measurements reveal the high quality of the grown layer. This technique will be useful to fabricate high-speed thin film transistors and high-efficiency optical devices on insulating substrates.

  7. Massive intoxication involving unusual high concentration of amitriptyline.

    PubMed

    Margalho, Cláudia; Barroso, Mário; Gallardo, Eugenia; Monsanto, Paula; Vieira, Duarte Nuno

    2007-08-01

    Amitriptyline is a tricyclic antidepressant widely used in the treatment of depression. Antidepressant drugs are among the most commonly encountered causes of self-poisoning, as illustrated by several published cases in the literature. This investigation reports a case of massive amitriptyline intoxication, involving a 44-year old female found dead in bed. The presence of this tricyclic antidepressant was revealed by a routine screening procedure. The concentration was calculated by gas chromatography/ electron ionization-mass spectrometry in the selected ion monitoring mode after solid-phase extraction using proadifen as internal standard and was in the post-mortem whole blood sample 85.9 mug/mL. This value was much higher than the reported toxic values ever found in the literature, and may therefore have caused the victim's death. Nortriptyline was also detected in the toxic concentration range, as well as therapeutic levels of diazepam and nor-diazepam. Taking into account both the available circumstantial information and toxicological results, it is very likely that death was caused by self-poisoning. Human & Experimental Toxicology (2007) 26, 667-670.

  8. The Effects of School Bonding on High School Seniors' Academic Achievement

    ERIC Educational Resources Information Center

    Bryan, Julia; Moore-Thomas, Cheryl; Gaenzle, Stacey; Kim, Jungnam; Lin, Chia-Huei; Na, Goeun

    2012-01-01

    The authors examine the effects of school bonding on academic achievement (measured by math achievement scores) in a sample of 12th graders from the Educational Longitudinal Study of 2002 (Ingels, Pratt, Rogers, Siegel, & Stutts, 2005). Components of school bonding have proximal and distal effects on academic achievement. Attachment to school and…

  9. Superintendent Leadership and Student Achievement in Suburban High Schools: A Sequential Explanatory Mixed Methods Analysis

    ERIC Educational Resources Information Center

    Kellner, Steven Reese

    2012-01-01

    This research study explored the critical nature of the connection between student achievement and superintendent leadership. A great deal of scholarship has addressed either student achievement or leadership and previous evidence has suggested the impact of both parental education and racioethnicity on student achievement, but few studies have…

  10. Process evaluation of enzymatic hydrolysis with filtrate recycle for the production of high concentration sugars.

    PubMed

    Xue, Ying; Rusli, Jannov; Chang, Hou-Min; Phillips, Richard; Jameel, Hasan

    2012-02-01

    Process simulation and lab trials were carried out to demonstrate and confirm the efficiency of the concept that recycling hydrolysate at low total solid enzymatic hydrolysis is one of the options to increase the sugar concentration without mixing problems. Higher sugar concentration can reduce the capital cost for fermentation and distillation because of smaller retention volume. Meanwhile, operation cost will also decrease for less operating volume and less energy required for distillation. With the computer simulation, time and efforts can be saved to achieve the steady state of recycling process, which is the scenario for industrial production. This paper, to the best of our knowledge, is the first paper discussing steady-state saccharification with recycling of the filtrate form enzymatic hydrolysis to increase sugar concentration. Recycled enzymes in the filtrate (15-30% of the original enzyme loading) resulted in 5-10% higher carbohydrate conversion compared to the case in which recycled enzymes were denatured. The recycled hydrolysate yielded 10% higher carbohydrate conversion compared to pure sugar simulated hydrolysate at the same enzyme loading, which indicated hydrolysis by-products could boost enzymatic hydrolysis. The high sugar concentration (pure sugar simulated) showed inhibition effect, since about 15% decrease in carbohydrate conversion was observed compared with the case with no sugar added. The overall effect of hydrolysate recycling at WinGEMS simulated steady-state conditions with 5% total solids was increasing the sugar concentration from 35 to 141 g/l, while the carbohydrate conversion was 2% higher for recycling at steady state (87%) compared with no recycling strategy (85%). Ten percent and 15% total solid processes were also evaluated in this study.

  11. Achieving high performance polymer tandem solar cells via novel materials design

    NASA Astrophysics Data System (ADS)

    Dou, Letian

    Organic photovoltaic (OPV) devices show great promise in low-cost, flexible, lightweight, and large-area energy-generation applications. Nonetheless, most of the materials designed today always suffer from the inherent disadvantage of not having a broad absorption range, and relatively low mobility, which limit the utilization of the full solar spectrum. Tandem solar cells provide an effective way to harvest a broader spectrum of solar radiation by combining two or more solar cells with different absorption bands. However, for polymer solar cells, the performance of tandem devices lags behind single-layer solar cells mainly due to the lack of suitable low-bandgap polymers (near-IR absorbing polymers). In this dissertation, in order to achieve high performance, we focus on design and synthesis of novel low bandgap polymers specifically for tandem solar cells. In Chapter 3, I demonstrate highly efficient single junction and tandem polymer solar cells featuring a spectrally matched low-bandgap conjugated polymer (PBDTT-DPP: bandgap, ˜1.44 eV). The polymer has a backbone based on alternating benzodithiophene and diketopyrrolopyrrole units. A single-layer device based on the polymer provides a power conversion efficiency of ˜6%. When the polymer is applied to tandem solar cells, a power conversion efficiency of 8.62% is achieved, which was the highest certified efficiency for a polymer solar cell. To further improve this material system, in Chapter 4, I show that the reduction of the bandgap and the enhancement of the charge transport properties of the low bandgap polymer PBDTT-DPP can be accomplished simultaneously by substituting the sulfur atoms on the DPP unit with selenium atoms. The newly designed polymer PBDTT-SeDPP (Eg = 1.38 eV) shows excellent photovoltaic performance in single junction devices with PCEs over 7% and photo-response up to 900 nm. Tandem polymer solar cells based on PBDTT-SeDPP are also demonstrated with a 9.5% PCE, which are more than 10

  12. Performance of a High-Concentration Erbium-Doped Fiber Amplifier with 100 nm Amplification Bandwidth

    SciTech Connect

    Hajireza, P.; Shahabuddin, N. S.; Abbasi-Zargaleh, S.; Emami, S. D.; Abdul-Rashid, H. A.; Yusoff, Z.

    2010-07-07

    Increasing demand for higher bandwidth has driven the need for higher Wavelength Division Multiplexing (WDM) channels. One of the requirements to achieve this is a broadband amplifier. This paper reports the performance of a broadband, compact, high-concentration and silica-based erbium-doped fiber amplifier. The amplifier optimized to a 2.15 m long erbium-doped fiber with erbium ion concentration of 2000 ppm. The gain spectrum of the amplifier has a measured amplification bandwidth of 100 nm using a 980 nm laser diode with power of 150 mW. This silica-based EDFA shows lower noise figure, higher gain and wider bandwidth in shorter wavelengths compared to Bismuth-based EDFA with higher erbium ion concentration of 3250 ppm at equivalent EDF length. The silica-based EDF shows peak gain at 22 dB and amplification bandwidth between 1520 nm and 1620 nm. The lowest noise figure is 5 dB. The gain is further improved with the implementation of enhanced EDFA configurations.

  13. Biodegradation of phenol at high initial concentration by Alcaligenes faecalis.

    PubMed

    Jiang, Yan; Wen, Jianping; Bai, Jing; Jia, Xiaoqiang; Hu, Zongding

    2007-08-17

    Strain Alcaligenes faecalis was isolated and identified as a member of the genus Alcaligenes by using BIOLOG and 16S rDNA sequence analysis. The phenol biodegradation tests showed that the phenol-degrading potential of A. faecalis related greatly to the different physiological phases of inoculum. The maximum phenol degradation occurred at the late phase of the exponential growth stages, where 1600 mg L(-1) phenol was completely degraded within 76 h. A. faecalis secreted and accumulated a vast quantity of phenol hydroxylase in this physiological phase, which ensured that the cells could quickly utilize phenol as a sole carbon and energy source. In addition, the kinetic behavior of A. faecalis in batch cultures was also investigated over a wide range of initial phenol concentrations (0-1600 mg L(-1)) by using Haldane model. It was clear that the Haldane kinetic model adequately described the dynamic behavior of the phenol biodegradation by the strain of A. faecalis.

  14. Achieving High-Energy-High-Power Density in a Flexible Quasi-Solid-State Sodium Ion Capacitor.

    PubMed

    Li, Hongsen; Peng, Lele; Zhu, Yue; Zhang, Xiaogang; Yu, Guihua

    2016-09-14

    Simultaneous integration of high-energy output with high-power delivery is a major challenge for electrochemical energy storage systems, limiting dual fine attributes on a device. We introduce a quasi-solid-state sodium ion capacitor (NIC) based on a battery type urchin-like Na2Ti3O7 anode and a capacitor type peanut shell derived carbon cathode, using a sodium ion conducting gel polymer as electrolyte, achieving high-energy-high-power characteristics in solid state. Energy densities can reach 111.2 Wh kg(-1) at power density of 800 W kg(-1), and 33.2 Wh kg(-1) at power density of 11200 W kg(-1), which are among the best reported state-of-the-art NICs. The designed device also exhibits long-term cycling stability over 3000 cycles with capacity retention ∼86%. Furthermore, we demonstrate the assembly of a highly flexible quasi-solid-state NIC and it shows no obvious capacity loss under different bending conditions.

  15. Characterization of the interactions within fine particle mixtures in highly concentrated suspensions for advanced particle processing.

    PubMed

    Otsuki, Akira; Bryant, Gary

    2015-12-01

    This paper aims to summarize recent investigations into the dispersion of fine particles, and the characterization of their interactions, in concentrated suspensions. This summary will provide a better understanding of the current status of this research, and will provide useful feedback for advanced particle processing. Such processes include the fabrication of functional nanostructures and the sustainable beneficiation of complex ores. For example, there has been increasing demand for complex ore utilization due to the noticeable decrease in the accessibility of high grade and easily extractable ores. In order to maintain the sustainable use of mineral resources, the effective beneficiation of complex ores is urgently required. It can be successfully achieved only with selective particle/mineral dispersion/liberation and the assistance of mineralogical and particle characterization.

  16. New insulating materials and their use to achieve high operating stresses in electrostatic machines

    NASA Astrophysics Data System (ADS)

    Cooke, Chathan M.

    1986-02-01

    Compressed gas insulation has provided the main insulation for sustaining terminal voltages of electrostatic accelerators. Essentially coaxial geometry is used with mechanical support of the terminal achieved by long columns which also support the acceleration tubes. Because of the vacuum insulation in the acceleration tubes, the electric gradient along the columns is typically 10-20 kV/cm, whereas the radial gas gap can operate at stresses about ten times larger. Until now, the terminal support has always been located in the low stress axial direction along the column and not in the radial high stress region. This paper is concerned with support insulation to be used in the radial direction. Advantages of radial supports include: simpler, more compact column structures, higher total voltages, and support of discrete stress redistribution electrodes such as vivitron. Important factors to the design of radial support insulators include the insulation constraints imposed by the gas gap, mechanical contact to the solid insulator, and basic limits of gas-solid dielectric interfaces. The gas gap insulation strength is shown to be limited by surface microirregularities and this accounts for electrode area and pressure effects. Based on the gas gap requirements, a design strategy for the insulators is developed. Epoxy is employed as the dielectric to allow the use of cast-in metal inserts at the ends. The inserts provide mechanical contact, shielding of the triple junction, and redistribution of the interface electric stresses. By careful design, the electric stress on the interface is made lower than that in the plain coaxial electrode gap. Practical experience shows that voltage increases linearly with insulator length and that designs achieve more than 10 MV/m into the multimegavolt region.

  17. Evaluation of dialyzer jacket structure and hollow-fiber dialysis membranes to achieve high dialysis performance.

    PubMed

    Hirano, Ayaka; Yamamoto, Ken-ichiro; Matsuda, Masato; Ogawa, Takehito; Yakushiji, Taiji; Miyasaka, Takehiro; Sakai, Kiyotaka

    2011-02-01

    The objective of this study was to determine the optimum dialyzer jacket structure and hollow-fiber dialysis membrane, both of which are indispensable factors for achieving high dialysis performance, by clarifying the relationship between the dialysis performance and the flow of dialysate and blood in a hollow-fiber dialyzer. We evaluated the clearance, dialysate, and blood flow for four commercially available hollow-fiber dialyzers, namely, the APS-15S, APS-15SA, TS-1.6UL, and CX-1.6U. To evaluate dialysate and blood flow, we measured the residence-time distribution of dialysate and blood flow of these dialyzers by the pulse-response method. We also determined the clearances of urea, creatinine, vitamin B(12), and lysozyme to evaluate the dialysis performance of these dialyzers. While the baffle and taper structures allow effective supply of dialysate into the dialyzer jacket, the hollow-fiber shape, inner diameter, and packing density significantly influence the dialysate flow. In dialyzers with long taper-holding slits, the slit area is a key design parameter for achieving optimum dialysate flow. Similarly, the blood flow is significantly influenced by the structure of the inflowing and outflowing blood ports at the header of a dialyzer, and the shape and inner diameter of the hollow fibers. Hollow fibers with smaller inner diameters cause an increase in blood pressure, which causes blood to enter the hollow fibers more easily. The hollow-fiber shape hardly affects the blood flow. While improved dialysate and blood flow cause higher clearance of low molecular-weight substances, higher membrane area and pure-water permeability accelerate internal filtration, thereby causing an increase in the clearance of large molecular-weight substances.

  18. Achieving Energy Savings with Highly-Controlled Lighting in an Open-Plan Office

    SciTech Connect

    Rubinstein, Francis; Enscoe, Abby

    2010-04-19

    An installation in a Federal building tested the effectiveness of a highly-controlled, workstation-specific lighting retrofit. The study took place in an open-office area with 86 cubicles and low levels of daylight. Each cubicle was illuminated by a direct/indirectpendant luminaire with three 32 watt lamps, two dimmable DALI ballasts, and an occupancy sensor. A centralized control system programmed all three lamps to turn on and off according to occupancy on a workstation-by-workstation basis. Field measurements taken over the course of several monthsdemonstrated 40% lighting energy savings compared to a baseline without advanced controls that conforms to GSA's current retrofit standard. A photometric analysis found that the installation provided higher desktop light levels than the baseline, while an occupant survey found that occupants in general preferred the lighting system to thebaseline.Simple payback is fairly high; projects that can achieve lower installation costs and/or higher energy savings and those in which greenhouse gas reduction and occupant satisfaction are significant priorities provide the ideal setting for workstation-specific lighting retrofits.

  19. Autonomous Information Fading and Provision to Achieve High Response Time in Distributed Information Systems

    NASA Astrophysics Data System (ADS)

    Lu, Xiaodong; Arfaoui, Helene; Mori, Kinji

    In highly dynamic electronic commerce environment, the need for adaptability and rapid response time to information service systems has become increasingly important. In order to cope with the continuously changing conditions of service provision and utilization, Faded Information Field (FIF) has been proposed. FIF is a distributed information service system architecture, sustained by push/pull mobile agents to bring high-assurance of services through a recursive demand-oriented provision of the most popular information closer to the users to make a tradeoff between the cost of information service allocation and access. In this paper, based on the analysis of the relationship that exists among the users distribution, information provision and access time, we propose the technology for FIF design to resolve the competing requirements of users and providers to improve users' access time. In addition, to achieve dynamic load balancing with changing users preference, the autonomous information reallocation technology is proposed. We proved the effectiveness of the proposed technology through the simulation and comparison with the conventional system.

  20. High-quality and high-purity homoepitaxial diamond (100) film growth under high oxygen concentration condition

    SciTech Connect

    Teraji, Tokuyuki

    2015-09-21

    Defect formation during diamond homoepitaxial growth was sufficiently inhibited by adding oxygen simultaneously in the growth ambient with high concentration of 2%. A 30-μm thick diamond films with surface roughness of <2 nm were homoepitaxially deposited on the (100) diamond single crystal substrates with reasonable growth rate of approximately 3 μm h{sup −1} under the conditions of higher methane concentration of 10%, higher substrate temperature of ∼1000 °C, and higher microwave power density condition of >100 W cm{sup −3}. Surface characteristic patterns moved to an identical direction with growth thickness, indicating that lateral growth was dominant growth mode. High chemical purity represented by low nitrogen concentration of less than 1 ppb and the highest {sup 12}C isotopic ratio of 99.998% of the obtained homoepitaxial diamond (100) films suggest that the proposed growth condition has high ability of impurity control.

  1. Determination of water quality variables, endotoxin concentration, and enterobacteriaceae concentration and identification in Southern High Plains dairy lagoons

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The objectives of this study were to determine the concentration of endotoxin, determine 20 water quality variables, and identify and enumerate fungal and bacterial pathogens from United States southern High Plains dairy lagoons and control lakes during summer and winter. Water samples were collecte...

  2. Preparation of high concentration polyaluminum chloride with high content of Alb or Alc.

    PubMed

    Zhao, Changwei; Zhang, Jingbo; Luan, Zhaokun; Peng, Xianjia; Ren, Xiaojing

    2009-01-01

    A novel membrane distillation concentration method was used to prepare high concentration polyaluminum chloride (PACl) with high content of Alb or Alc. 2.52 mol/L PACl1 with 88% Alb and 2.38 mol/L PACl2 with 61% Alc were successfully prepared. Three coagulants, AlCl3, PACl1 and PACl2 were investigated on their hydrolysis behavior and speciation under different conditions. The effects of pH and dilution ratio on Al species distribution were investigated by ferron assay. Experimental result showed that pH had a significant effect on Al species distribution for the three coagulants. Dilution ratio had little effects on Alb and Alc distribution in whole dilution process except the beginning for PACl1 and PACl2. The results indicated that transformation of Al depends largely on their original composition. AlCl3 was the most unstable coagulant among these three coagulants during hydrolysis process. PACl1 and PACl2 with significant amounts of highly charged and stable polynuclear aluminum hydrolysis products were less affected by the hydrolysis conditions and could maintain high speciation stability under various conditions.

  3. Titanium doped silicon layers with very high concentration

    SciTech Connect

    Olea, J.; Toledano-Luque, M.; Pastor, D.; Gonzalez-Diaz, G.; Martil, I.

    2008-07-01

    Ion implantation of Ti into Si at high doses has been performed. After laser annealing the maximum average of substitutional Ti atoms is about 10{sup 18} cm{sup -3}. Hall effect measurements show n-type samples with mobility values of about 400 cm{sup 2}/V s at room temperature. These results clearly indicate that Ti solid solubility limit in Si has been exceeded by far without the formation of a titanium silicide layer. This is a promising result toward obtaining of an intermediate band into Si that allows the design of a new generation of high efficiency solar cell using Ti implanted Si wafers.

  4. High Efficiency Nanostructured III-V Photovoltaics for Solar Concentrator Application

    SciTech Connect

    Hubbard, Seth

    2012-09-12

    The High Efficiency Nanostructured III-V Photovoltaics for Solar Concentrators project seeks to provide new photovoltaic cells for Concentrator Photovoltaics (CPV) Systems with higher cell efficiency, more favorable temperature coefficients and less sensitivity to changes in spectral distribution. The main objective of this project is to provide high efficiency III-V solar cells that will reduce the overall cost per Watt for power generation using CPV systems.This work is focused both on a potential near term application, namely the use of indium arsenide (InAs) QDs to spectrally "tune" the middle (GaAs) cell of a SOA triple junction device to a more favorable effective bandgap, as well as the long term goal of demonstrating intermediate band solar cell effects. The QDs are confined within a high electric field i-region of a standard GaAs solar cell. The extended absorption spectrum (and thus enhanced short circuit current) of the QD solar cell results from the increase in the sub GaAs bandgap spectral response that is achievable as quantum dot layers are introduced into the i-region. We have grown InAs quantum dots by OMVPE technique and optimized the QD growth conditions. Arrays of up to 40 layers of strain balanced quantum dots have been experimentally demonstrated with good material quality, low residual stain and high PL intensity. Quantum dot enhanced solar cells were grown and tested under simulated one sun AM1.5 conditions. Concentrator solar cells have been grown and fabricated with 5-40 layers of QDs. Testing of these devices show the QD cells have improved efficiency compared to baseline devices without QDs. Device modeling and measurement of thermal properties were performed using Crosslight APSYS. Improvements in a triple junction solar cell with the insertion of QDs into the middle current limiting junction was shown to be as high as 29% under one sun illumination for a 10 layer stack QD enhanced triple junction solar cell. QD devices have strong

  5. "I am a scientist": How setting conditions that enhance focused concentration positively relate to student motivation and achievement outcomes in inquiry-based science

    NASA Astrophysics Data System (ADS)

    Ellwood, Robin B.

    This research investigated how student social interactions within two approaches to an inquiry-based science curriculum could be related to student motivation and achievement outcomes. This qualitative case study consisted of two cases, Off-Campus and On-Campus, and used ethnographic techniques of participant observation. Research participants included eight eighth grade girls, aged thirteen to fourteen years old. Data sources included formal and informal participant interviews, participant journal reflections, curriculum artifacts including quizzes, worksheets, and student-generated research posters, digital video and audio recordings, photographs, and researcher field notes. Data were transcribed verbatim and coded, then collapsed into emergent themes using NVIVO 9. The results of this research illustrate how setting conditions that promote focused concentration and communicative interactions can be positively related to student motivation and achievement outcomes in inquiry-based science. Participants in the Off-Campus case experienced more frequent states of focused concentration and out performed their peers in the On-Campus case on forty-six percent of classroom assignments. Off-Campus participants also designed and implemented a more cognitively complex research project, provided more in-depth analyses of their research results, and expanded their perceptions of what it means to act like a scientist to a greater extent than participants in the On-Campus case. These results can be understood in relation to Flow Theory. Student interactions that promoted the criteria necessary for initiating flow, which included having clearly defined goals, receiving immediate feedback, and maintaining a balance between challenges and skills, fostered enhanced student motivation and achievement outcomes. This research also illustrates the positive gains in motivation and achievement outcomes that emerge from student experiences with extended time in isolated areas referred to

  6. Tracking performance with two breathing oxygen concentrations after high altitude rapid decompression

    NASA Technical Reports Server (NTRS)

    Nesthus, Thomas E.; Schiflett, Samuel G.; Oakley, Carolyn J.

    1992-01-01

    Current military aircraft Liquid Oxygen (LOX) systems supply 99.5 pct. gaseous Aviator's Breathing Oxygen (ABO) to aircrew. Newer Molecular Sieve Oxygen Generation Systems (MSOGS) supply breathing gas concentration of 93 to 95 pct. O2. The margin is compared of hypoxia protection afforded by ABO and MSOGS breathing gas after a 5 psi differential rapid decompression (RD) in a hypobaric research chamber. The barometric pressures equivalent to the altitudes of 46000, 52000, 56000, and 60000 ft were achieved from respective base altitudes in 1 to 1.5 s decompressions. During each exposure, subjects remained at the simulated peak altitude breathing either 100 or 94 pct. O2 with positive pressure for 60 s, followed by a rapid descent to 40000 ft. Subjects used the Tactical Life Support System (TLSS) for high altitude protection. Subcritical tracking task performance on the Performance Evaluation Device (PED) provided psychomotor test measures. Overall tracking task performance results showed no differences between the MSOGS breathing O2 concentration of 94 pct. and ABO. Significance RMS error differences were found between the ground level and base altitude trials compared to peak altitude trials. The high positive breathing pressures occurring at the peak altitudes explained the differences.

  7. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

    NASA Astrophysics Data System (ADS)

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-08-01

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

  8. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

    PubMed Central

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-01-01

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes. PMID:27545955

  9. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination.

    PubMed

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-08-22

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

  10. Reusable chelating resins concentrate metal ions from highly dilute solutions

    NASA Technical Reports Server (NTRS)

    Bauman, A. J.; Weetal, H. H.; Weliky, N.

    1966-01-01

    Column chromatographic method uses new metal chelating resins for recovering heavy-metal ions from highly dilute solutions. The absorbed heavy-metal cations may be removed from the chelating resins by acid or base washes. The resins are reusable after the washes are completed.

  11. Bryant Junior High School Concentrated Education Center Reading Program.

    ERIC Educational Resources Information Center

    Asplund, Bennett; Benolken, David

    This report, included in "Effective Reading Programs...," describes a Title I sequential reading support program for educationally disadvantaged junior high school students and analyzes the vocabulary and reading comprehension test results of this program for the school year 1972-1973. After group and individual pretesting in reading and…

  12. Qualitative research study of high-achieving females' life experiences impacting success

    NASA Astrophysics Data System (ADS)

    Butcher, Ann Patrice

    2003-07-01

    This qualitative study investigated the life experiences of five academically gifted female students in math and science in reflection of their elementary learning prior to enrollment at a prestigious science and mathematics high school. The elite high school limits admission to the state of Illinois' top students. The purpose of this study is to unfold the story of five academically gifted females in attendance at the elite high school reflecting on their life experiences in elementary school that contributed to their current academic success. Twelve female students, who at the time of this study were currently in their senior year (12th grade) of high school, were solicited from the top academic groups who are regarded by their teachers as highly successful in class. Students were selected as part of the study based on academic status, survey completion and interest in study, Caucasian and Asian ethnicity, locale of elementary school with preference given to the variety of school demographics---urban, suburban, and rural---further defined the group to the core group of five. All female participants were personally interviewed and communicated via Internet with the researcher. Parents and teachers completing surveys as well met the methodological requirements of triangulation. An emergent theme of paternal influence came from the research. Implications supported in the research drawn from this study to increase achievement of academically gifted females include: (a) proper early identification of learner strengths plays a role; (b) learning with appropriate intellectual peers is more important than learning with their age group; (c) teachers are the greatest force for excellent instruction; (d) effective teaching strategies include cooperative learning, multi-sensory learning, problem-based learning, and hands-on science; (e) rigor in math is important; (f) gender and stereotypes need not be barriers; (g) outside interests and activities are important for self

  13. Optimal microelectromechanical systems (MEMS) device for achieving high pyroelectric response of AlN

    NASA Astrophysics Data System (ADS)

    Kebede, Bemnnet; Coutu, Ronald A.; Starman, LaVern

    2014-03-01

    This paper discusses research being conducted on aluminum nitride (AlN) as a pyroelectric material for use in detecting applications. AlN is being investigated because of its high pyroelectric coefficient, thermal stability, and high Curie temperature. In order to determine suitability of the pyroelectric properties of AlN for use as a detector, testing of several devices was conducted. These devices were fabricated using microelectromechanical systems (MEMS) fabrication processes; the devices were also designed to allow for voltage and current measurements. The deposited AlN films used were 150 nm - 300 nm in thickness. Thin-films were used to rapidly increase the temperature response after the thermal stimulus was applied to the pyroelectric material. This is important because the pyroelectric effect is directly proportional to the rate of temperature change. The design used was a face-electrode bridge that provides thermal isolation which minimizes heat loss to the substrate, thereby increasing operation frequency of the pyroelectric device. A thermal stimulus was applied to the pyroelectric material and the response was measured across the electrodes. A thermal imaging camera was used to monitor the changes in temperature. Throughout the testing process, the annealing temperatures, type of layers, and thicknesses were also varied. These changes resulted in improved MEMS designs, which were fabricated to obtain an optimal design configuration for achieving a high pyroelectric response. A pyroelectric voltage response of 38.9 mVp-p was measured without filtering, 12.45 mVp-p was measured in the infrared (IR) region using a Si filter, and 6.38 mVp-p was measured in the short wavelength IR region using a long pass filter. The results showed that AlN's pyroelectric properties can be used in detecting applications.

  14. Longitudinal Outcomes of Start Time Delay on Sleep, Behavior, and Achievement in High School

    PubMed Central

    Thacher, Pamela V.; Onyper, Serge V.

    2016-01-01

    Study Objectives: To establish whether sleep, health, mood, behavior, and academics improved after a 45-minute delay in high school start time, and whether changes persisted longitudinally. Methods: We collected data from school records and student self-report across a number of domains at baseline (May 2012) and at two follow-up time points (November 2012 and May 2013), at a public high school in upstate New York. Students enrolled during academic years (AY) 2011–2012 and 2012–2013 completed the Pittsburgh Sleep Quality Index; the DASS-21; the “Owl-Lark” Scale; the Daytime Sleepiness Index; and a brief self-report of health. Reports from school records regarding attendance, tardiness, disciplinary violations, and academic performance were collected for AY 2010–2011 through 2013–2014. Results: Students delayed but did not extend their sleep period; we found lasting improvements in tardiness and disciplinary violations after the start-time delay, but no changes to other variables. At the first follow-up, students reported 20 minutes longer sleep, driven by later rise times and stable bed times. At the second follow-up, students maintained later rise times but delayed bedtimes, returning total sleep to baseline levels. A delay in rise time, paralleling the delay in the start time that occurred, resulted in less tardiness and decreased disciplinary incidents, but larger improvements to sleep patterns may be necessary to affect health, attendance, sleepiness, and academic performance. Conclusions: Later start times improved tardiness and disciplinary issues at this school district. A delay in start time may be a necessary but not sufficient means to increase sleep time and may depend on preexisting individual differences. Commentary: A commentary on this article appears in this issue on page 267. Citation: Thacher PV, Onyper SV. Longitudinal outcomes of start time delay on sleep, behavior, and achievement in high school. SLEEP 2016;39(2):271–281. PMID

  15. Production of Isolated Giant Unilamellar Vesicles under High Salt Concentrations

    PubMed Central

    Stein, Hannah; Spindler, Susann; Bonakdar, Navid; Wang, Chun; Sandoghdar, Vahid

    2017-01-01

    The cell membrane forms a dynamic and complex barrier between the living cell and its environment. However, its in vivo studies are difficult because it consists of a high variety of lipids and proteins and is continuously reorganized by the cell. Therefore, membrane model systems with precisely controlled composition are used to investigate fundamental interactions of membrane components under well-defined conditions. Giant unilamellar vesicles (GUVs) offer a powerful model system for the cell membrane, but many previous studies have been performed in unphysiologically low ionic strength solutions which might lead to altered membrane properties, protein stability and lipid-protein interaction. In the present work, we give an overview of the existing methods for GUV production and present our efforts on forming single, free floating vesicles up to several tens of μm in diameter and at high yield in various buffer solutions with physiological ionic strength and pH. PMID:28243205

  16. High plasma uric acid concentration: causes and consequences

    PubMed Central

    2012-01-01

    High plasma uric acid (UA) is a precipitating factor for gout and renal calculi as well as a strong risk factor for Metabolic Syndrome and cardiovascular disease. The main causes for higher plasma UA are either lower excretion, higher synthesis or both. Higher waist circumference and the BMI are associated with higher insulin resistance and leptin production, and both reduce uric acid excretion. The synthesis of fatty acids (tryglicerides) in the liver is associated with the de novo synthesis of purine, accelerating UA production. The role played by diet on hyperuricemia has not yet been fully clarified, but high intake of fructose-rich industrialized food and high alcohol intake (particularly beer) seem to influence uricemia. It is not known whether UA would be a causal factor or an antioxidant protective response. Most authors do not consider the UA as a risk factor, but presenting antioxidant function. UA contributes to > 50% of the antioxidant capacity of the blood. There is still no consensus if UA is a protective or a risk factor, however, it seems that acute elevation is a protective factor, whereas chronic elevation a risk for disease. PMID:22475652

  17. Deep Sea Memory of High Atmospheric CO2 Concentration

    NASA Astrophysics Data System (ADS)

    Mathesius, Sabine; Hofmann, Matthias; Caldeira, Ken; Schellnhuber, Hans Joachim

    2015-04-01

    Carbon dioxide removal (CDR) from the atmosphere has been proposed as a powerful measure to mitigate global warming and ocean acidification. Planetary-scale interventions of that kind are often portrayed as "last-resort strategies", which need to weigh in if humankind keeps on enhancing the climate-system stock of CO2. Yet even if CDR could restore atmospheric CO2 to substantially lower concentrations, would it really qualify to undo the critical impacts of past emissions? In the study presented here, we employed an Earth System Model of Intermediate Complexity (EMIC) to investigate how CDR might erase the emissions legacy in the marine environment, focusing on pH, temperature and dissolved oxygen. Against a background of a world following the RCP8.5 emissions path ("business-as-usual") for centuries, we simulated the effects of two massive CDR interventions with CO2 extraction rates of 5 GtC yr-1 and 25 GtC yr-1, respectively, starting in 2250. We found that the 5 GtC yr-1 scheme would have only minor ameliorative influence on the oceans, even after several centuries of application. By way of contrast, the extreme 25 GtC yr-1 scheme eventually leads to tangible improvements. However, even with such an aggressive measure, past CO2 emissions leave a substantial legacy in the marine environment within the simulated period (i.e., until 2700). In summary, our study demonstrates that anthropogenic alterations of the oceans, caused by continued business-as-usual emissions, may not be reversed on a multi-centennial time scale by the most aspirational geoengineering measures. We also found that a transition from the RCP8.5 state to the state of a strong mitigation scenario (RCP2.6) is not possible, even under the assumption of extreme extraction rates (25 GtC yr-1). This is explicitly demonstrated by simulating additional scenarios, starting CDR already in 2150 and operating until the atmospheric CO2 concentration reaches 280 ppm and 180 ppm, respectively. The simulated

  18. Performance Assessment of High and Low Income Families through "Online RAW Achievement Battery Test" of Primary Grade Students

    ERIC Educational Resources Information Center

    Ahmed, Tamim; Hanif, Maria

    2016-01-01

    This study is intended to investigate student's achievement capability among two families i.e. Low and High income families and designed for primary level learners. A Reading, Arithmetic and Writing (RAW) Achievement test that was developed as a part of another research study (Tamim Ahmed Khan, 2015) was adopted for this study. Both English medium…

  19. Bright and Beautiful: High Achieving Girls, Ambivalent Femininities, and the Feminization of Success in the Primary School

    ERIC Educational Resources Information Center

    Renold, Emma; Allan, Alexandra

    2006-01-01

    This paper refocuses attention on and problematizes girls' experiences of school achievement and the construction of schoolgirl femininities. In particular, it centres on the relatively neglected experiences and identity work of high achieving primary school girls. Drawing upon ethnographic data (observations, interviews, and pupil diaries) from a…

  20. (Re)Defining the Narrative: High-Achieving Nontraditional Black Male Undergraduates at a Historically Black College and University

    ERIC Educational Resources Information Center

    Goings, Ramon B.

    2016-01-01

    Using Harper's anti-deficit achievement framework as a theoretical guide, the purpose of this phenomenological study was to investigate the academic and social experiences of four nontraditional, high-achieving, Black male undergraduates attending one historically Black university. Findings show that the participants were intrinsically motivated…

  1. The Relationship between Professional Learning Community Implementation and Academic Achievement and Graduation Rates in Georgia High Schools

    ERIC Educational Resources Information Center

    Hardinger, Regina Gail

    2013-01-01

    Many educational administrators in Georgia continue to struggle with low student academic achievement and low high school graduation rates. DuFour's professional learning community (PLC) theory suggests a positive relationship between levels of PLC implementation and academic achievement and between levels of PLC implementation and graduation…

  2. The Relationship between Professional Learning Communities, Personal Teacher Efficacy, and Student Achievement at the High School Level

    ERIC Educational Resources Information Center

    Brooks, Sherri L.

    2013-01-01

    The purpose of this correlational study was to determine if there was a relationship between professional learning community (PLC), personal teacher efficacy (PTE), and student achievement. The study examined teacher perception of PLC implementation and PET as it related to student achievement at the high school level on the Virginia End-of Course…

  3. American High School Students from Different Ethnic Backgrounds: The Role of Parents and the Classroom in Achievement Motivation

    ERIC Educational Resources Information Center

    Kim, Jung-In

    2015-01-01

    The purpose of this study was to investigate the relationships between ethnically diverse US high school students' (N = 331) perceptions of their parents' or classroom's motivating factors and their achievement motivation in their math class, connecting achievement goal orientation and self-determination theories. Two hypothesized path models were…

  4. Academic Achievement Trajectories of Homeless and Highly Mobile Students: Resilience in the Context of Chronic and Acute Risk

    ERIC Educational Resources Information Center

    Cutuli, J. J.; Desjardins, Christopher David; Herbers, Janette E.; Long, Jeffrey D.; Heistad, David; Chan, Chi-Keung; Hinz, Elizabeth; Masten, Ann S.

    2013-01-01

    Analyses examined academic achievement data across third through eighth grades ("N" = 26,474), comparing students identified as homeless or highly mobile (HHM) with other students in the federal free meal program (FM), reduced price meals (RM), or neither (General). Achievement was lower as a function of rising risk status (General…

  5. A Longitudinal Study of the Social Distribution of Mathematics Achievement for a Cohort of Public High School Students.

    ERIC Educational Resources Information Center

    Mandeville, Garrett K.; Kennedy, Eugene

    This paper reports the results of a study of changes in the social distribution of mathematics achievement for a cohort of public high school students. Using hierarchical linear modeling (HLM) the study sought to identify school characteristics which were significantly correlated with changes in achievement differences from grade 9 to grade 11…

  6. Differences in Self-Concept among Children with Mathematics Disabilities and Their Average and High Achieving Peers

    ERIC Educational Resources Information Center

    Zeleke, Seleshi

    2004-01-01

    Self-concept ratings of children with mathematics disabilities (MD), average mathematics achievement (AA), and high mathematics achievement (HA) who attended regular classes in grades 4 through 6 were compared. Twenty-four children in each group, who were selected from an original pool of 811 children, and who were matched one-to-one by grade,…

  7. Intercomparison of high-volume PM10 samplers at a site with high-particulate concentrations

    SciTech Connect

    Purdue, L.J.; Rodes, C.E.; Rehme, K.A.; Holland, D.M.; Bond, A.E.

    1986-01-01

    Commercially available high-volume PM10 samplers were intercompared at a site in Phoenix characterized by high concentrations of coarse particles. Over a 21-day period, Sierra Andersen 321A (SA 321A) samplers gave PM10 measurements 58% higher than the Wedding IP10 (WED) samplers and 16% higher than a SA 321A sampler that had an oil coating on the internal impaction surfaces of the inlet. WED samplers that were subjected to a simple brush-cleaning procedure after each sampling period gave PM10 results 16% higher than the WED samplers not subjected to cleaning. The oiled SA 321A sampler gave PM10 values 15% higher than the cleaned WED samplers. The results demonstrate that the SA 321A overestimates PM10 when sampling in an environment with high coarse-particle concentrations. The over collection results from pass-through of large particles, and can be minimized by oiling the internal impaction surfaces of the inlet. The WED sampler underestimates PM10 after several days of sampling in such an environment.

  8. A comparison of rural high school students in Germany with rural Tennessee high school students' mathematics and science achievement

    NASA Astrophysics Data System (ADS)

    Harding, R. Fredrick

    This descriptive study compared the science and mathematics aptitudes and achievement test scores for the final school year students in rural White County and Van Buren County, Tennessee with rural county students in Germany. In accordance with the previous research literature (Stevenson, 2002), German students outperformed U.S. students on The International Trends in Math and Science test (TIMSS). As reform in the U.S. education system has been underway, this study intended to compare German county student final school year performance with White County and Van Buren County (Grade 12) performance in science and mathematics. The entire populations of 176 White and Van Buren Counties senior high final school year students were compared with 120 school final year students from two rural German county high schools. The student responses to identical test and questionnaire items were compared using the t-test statistical analysis. In conclusion after t-test analyses, there was no significant difference (p>.05 level) in student attitudes on the 27 problem achievement and the 35 TIMSS questionnaire items between the sampled population of 120 German students compared with the population of 176 White and Van Buren students. Also, there was no statistically significant difference (p>.05 level) between the German, White, and Van Buren County rural science and math achievement in the TIMSS problem section of the final year test. Based on the research, recommendations to improve U.S. student scores to number one in the world include making changes in teaching methodology in mathematics and science; incorporating pamphlet lessons rather than heavily reliance on textbooks; focusing on problem solving; establishing an online clearinghouse for effective lessons; creating national standards in mathematics and science; matching students' course choices to job aspirations; tracking misbehaving students rather than mainstreaming them into the regular classroom; and designing

  9. High-concentration boron doping of graphene nanoplatelets by simple thermal annealing and their supercapacitive properties

    NASA Astrophysics Data System (ADS)

    Yeom, Da-Young; Jeon, Woojin; Tu, Nguyen Dien Kha; Yeo, So Young; Lee, Sang-Soo; Sung, Bong June; Chang, Hyejung; Lim, Jung Ah; Kim, Heesuk

    2015-05-01

    For the utilization of graphene in various energy storage and conversion applications, it must be synthesized in bulk with reliable and controllable electrical properties. Although nitrogen-doped graphene shows a high doping efficiency, its electrical properties can be easily affected by oxygen and water impurities from the environment. We here report that boron-doped graphene nanoplatelets with desirable electrical properties can be prepared by the simultaneous reduction and boron-doping of graphene oxide (GO) at a high annealing temperature. B-doped graphene nanoplatelets prepared at 1000 °C show a maximum boron concentration of 6.04 ± 1.44 at %, which is the highest value among B-doped graphenes prepared using various methods. With well-mixed GO and g-B2O3 as the dopant, highly uniform doping is achieved for potentially gram-scale production. In addition, as a proof-of-concept, highly B-doped graphene nanoplatelets were used as an electrode of an electrochemical double-layer capacitor (EDLC) and showed an excellent specific capacitance value of 448 F/g in an aqueous electrolyte without additional conductive additives. We believe that B-doped graphene nanoplatelets can also be used in other applications such as electrocatalyst and nano-electronics because of their reliable and controllable electrical properties regardless of the outer environment.

  10. View looking northwest toward HIghGrade Ore Bin and Concentrate Bin ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View looking northwest toward HIgh-Grade Ore Bin and Concentrate Bin - Kennecott Copper Corporation, Concentration Mill, On Copper River & Northwestern Railroad, Kennicott, Valdez-Cordova Census Area, AK

  11. New Powder Metallurgical Approach to Achieve High Fatigue Strength in Ti-6Al-4V Alloy

    NASA Astrophysics Data System (ADS)

    Cao, Fei; Ravi Chandran, K. S.; Kumar, Pankaj; Sun, Pei; Zak Fang, Z.; Koopman, Mark

    2016-05-01

    Recently, manufacturing of titanium by sintering and dehydrogenation of hydride powders has generated a great deal of interest. An overarching concern regarding powder metallurgy (PM) titanium is that critical mechanical properties, especially the high-cycle fatigue strength, are lower than those of wrought titanium alloys. It is demonstrated here that PM Ti-6Al-4V alloy with mechanical properties comparable (in fatigue strength) and exceeding (in tensile properties) those of wrought Ti-6Al-4V can be produced from titanium hydride powder, through the hydrogen sintering and phase transformation process. Tensile and fatigue behavior, as well as fatigue fracture mechanisms, have been investigated under three processing conditions. It is shown that a reduction in the size of extreme-sized pores by changing the hydride particle size distribution can lead to improved fatigue strength. Further densification by pneumatic isostatic forging leads to a fatigue strength of ~550 MPa, comparable to the best of PM Ti-6Al-4V alloys prepared by other methods and approaching the fatigue strengths of wrought Ti-6Al-4V alloys. The microstructural factors that limit fatigue strength in PM titanium have been investigated, and pathways to achieve greater fatigue strengths in PM Ti-6Al-4V alloys have been identified.

  12. The Stories Clinicians Tell: Achieving High Reliability and Improving Patient Safety

    PubMed Central

    Cohen, Daniel L; Stewart, Kevin O

    2016-01-01

    The patient safety movement has been deeply affected by the stories patients have shared that have identified numerous opportunities for improvements in safety. These stories have identified system and/or human inefficiencies or dysfunctions, possibly even failures, often resulting in patient harm. Although patients’ stories tell us much, less commonly heard are the stories of clinicians and how their personal observations regarding the environments they work in and the circumstances and pressures under which they work may degrade patient safety and lead to harm. If the health care industry is to function like a high-reliability industry, to improve its processes and achieve the outcomes that patients rightly deserve, then leaders and managers must seek and value input from those on the front lines—both clinicians and patients. Stories from clinicians provided in this article address themes that include incident identification, disclosure and transparency, just culture, the impact of clinical workload pressures, human factors liabilities, clinicians as secondary victims, the impact of disruptive and punitive behaviors, factors affecting professional morale, and personal failings. PMID:26580146

  13. Fair and Just Culture, Team Behavior, and Leadership Engagement: The Tools to Achieve High Reliability

    PubMed Central

    Frankel, Allan S; Leonard, Michael W; Denham, Charles R

    2006-01-01

    Background Disparate health care provider attitudes about autonomy, teamwork, and administrative operations have added to the complexity of health care delivery and are a central factor in medicine's unacceptably high rate of errors. Other industries have improved their reliability by applying innovative concepts to interpersonal relationships and administrative hierarchical structures (Chandler 1962). In the last 10 years the science of patient safety has become more sophisticated, with practical concepts identified and tested to improve the safety and reliability of care. Objective Three initiatives stand out as worthy regarding interpersonal relationships and the application of provider concerns to shape operational change: The development and implementation of Fair and Just Culture principles, the broad use of Teamwork Training and Communication, and tools like WalkRounds that promote the alignment of leadership and frontline provider perspectives through effective use of adverse event data and provider comments. Methods Fair and Just Culture, Teamwork Training, and WalkRounds are described, and implementation examples provided. The argument is made that they must be systematically and consistently implemented in an integrated fashion. Conclusions There are excellent examples of institutions applying Just Culture principles, Teamwork Training, and Leadership WalkRounds—but to date, they have not been comprehensively instituted in health care organizations in a cohesive and interdependent manner. To achieve reliability, organizations need to begin thinking about the relationship between these efforts and linking them conceptually. PMID:16898986

  14. Achieving high survival of tournament-caught black bass: past efforts and future needs and opportunities

    USGS Publications Warehouse

    Schramm, Harold; Gilliland, Gene

    2015-01-01

    Rapid growth of black bass (Micropterus spp.) tournaments in the 1960s and 1970s caused concern among fisheries managers and anglers about the impacts of tournament-caused mortality on bass populations. Tournament organizers voluntarily implemented live-release events in the early 1980s. As catch-and-release practices became more common, procedures to improve the survival of tournament-caught fish were developed and have evolved. The objectives of this paper are to review education and outreach efforts to improve survival of tournament-caught black bass, suggest research needs and opportunities to achieve greater survival, and show the relevance of high survival to contemporary black bass management. Since 1985, a succession of informational products describing those techniques have been developed and distributed to anglers. Although research has confirmed the effectiveness of the recommended procedures and documented that angler and tournament organizer behavior has changed and the survival of tournament-caught black bass has increased, the impacts of the outreach efforts on tournament practices have not been quantified. Continued efforts towards increasing angler awareness of proper handling techniques may benefit from better communication, endorsement by professional anglers, and the use of incentives by state agencies to encourage better fish care.

  15. Achieving high-precision pointing on ExoplanetSat: initial feasibility analysis

    NASA Astrophysics Data System (ADS)

    Pong, Christopher M.; Lim, Sungyung; Smith, Matthew W.; Miller, David W.; Villaseñor, Jesus S.; Seager, Sara

    2010-07-01

    ExoplanetSat is a proposed three-unit CubeSat designed to detect down to Earth-sized exoplanets in an orbit out to the habitable zone of Sun-like stars via the transit method. To achieve the required photometric precision to make these measurements, the target star must remain within the same fraction of a pixel, which is equivalent to controlling the pointing of the satellite to the arcsecond level. The satellite will use a two-stage control system: coarse control will be performed by a set of reaction wheels, desaturated by magnetic torque coils, and fine control will be performed by a piezoelectric translation stage. Since no satellite of this size has previously demonstrated this high level of pointing precision, a simulation has been developed to prove the feasibility of realizing such a system. The current baseline simulation has demonstrated the ability to hold the target star to within 0.05 pixels or 1.8 arcseconds (with an 85 mm lens and 15 μm pixels), in the presence of large reaction wheel disturbances as well as external environmental disturbances. This meets the current requirement of holding the target star to 0.14 pixels or 5.0 arcseconds. Other high-risk aspects of the design have been analyzed such as the effect of changing the guide star centroiding error, changing the CMOS sampling frequency, and reaction wheel selection on the slew performance of the satellite. While these results are promising as an initial feasibility analysis, further model improvements and hardware-in-the-loop tests are currently underway.

  16. Motivational Factors Contributing to Turkish High School Students' Achievement in Gases and Chemical Reactions

    ERIC Educational Resources Information Center

    Kadioglu, Cansel; Uzuntiryaki, Esen

    2008-01-01

    This study aimed to investigate the contribution of motivational factors to 10th grade students' achievement in gases and chemical reactions in chemistry. Three hundred fifty nine 10th grade students participated in the study. The Gases and Chemical Reactions Achievement Test and the Motivated Strategies for Learning Questionnaire were…

  17. Job Choice As a Function of SES and Achievement Scores For High School Students.

    ERIC Educational Resources Information Center

    Nelms, Charlie; And Others

    1982-01-01

    Investigated impact of socio-economic status (SES) and achievement scores on job choice for 128 participants in a Labor Market Orientation Training program. Neither SES nor the program measure ("World of Work") were significant, but "Wide Range Achievement Test" gain scores did significantly impact on job choice. (Author/BRR)

  18. Social Adaptation and Its Relationship to Achievement Motivation among High School Students in Jordan

    ERIC Educational Resources Information Center

    AlZboon, Saleem Odeh

    2013-01-01

    The study amid at exploring and detecting the level of social adaptation and its relationship with the achievement motivation of the secondary school students in Jordan, the study sample consisted of 495 secondary school students in the province of Jerash, and to achieve the objective of this study comes the development of two tools: the first one…

  19. Achievement Goal Validation among African American High School Students: CFA and Rasch Results

    ERIC Educational Resources Information Center

    Hart, Caroline O.; Mueller, Christian E.; Royal, Kenneth D.; Jones, Martin H.

    2013-01-01

    Achievement goal theory helps describe how and why students engage in various academic behaviors. Historically, achievement goals have been examined almost exclusively with undergraduate, nonminority samples, and predominately with factor analytic techniques. The present study adds to a growing literature by providing initial validation of a…

  20. Longitudinal Analysis of Chinese High School Student's Stress in School and Academic Achievement

    ERIC Educational Resources Information Center

    Liu, Yangyang; Lu, Zuhong

    2011-01-01

    In previous research, few studies have examined the effects of adolescents' stress in school on the change rates of their academic achievement. In the present study, we seek to examine the longitudinal relationships between adolescents' stress in school and the change rates of their academic achievement. The results indicated that for those whose…