Science.gov

Sample records for acid buffer solution

  1. THE KINETICS OF SAPONIFICATION OF IODOACETIC ACID BY SODIUM HYDROXIDE AND BY CERTAIN ALKALINE BUFFER SOLUTIONS.

    PubMed

    Brdicka, R

    1936-07-20

    1. The rate of the saponification of iodoacetic acid in sodium hydroxide and alkaline buffer solutions yielding glycollic acid was measured by means of Heyrovský's polarographic method. 2. From the bimolecular velocity constants, increasing with the ionic strength of the solution, the Brönsted factor, F, which characterizes the primary salt effect, was calculated. 3. In the borate buffer solutions the monomolecular constants of the saponification were determined which, at values above the pH of neutralization of boric acid, show a proportionality to the concentration of hydroxyl anions. Below the pH of neutralization of boric acid, they are proportional to the concentration of borate anions.

  2. Comparison of peak shape in hydrophilic interaction chromatography using acidic salt buffers and simple acid solutions.

    PubMed

    Heaton, James C; Russell, Joseph J; Underwood, Tim; Boughtflower, Robert; McCalley, David V

    2014-06-20

    The retention and peak shape of neutral, basic and acidic solutes was studied on hydrophilic interaction chromatography (HILIC) stationary phases that showed both strong and weak ionic retention characteristics, using aqueous-acetonitrile mobile phases containing either formic acid (FA), ammonium formate (AF) or phosphoric acid (PA). The effect of organic solvent concentration on the results was also studied. Peak shape was good for neutrals under most mobile phase conditions. However, peak shapes for ionised solutes, particularly for basic compounds, were considerably worse in FA than AF. Even neutral compounds showed deterioration in performance with FA when the mobile phase water concentration was reduced. The poor performance in FA cannot be entirely attributed to the negative impact of ionic retention on ionised silanols on the underlying silica base materials, as results using PA at lower pH (where their ionisation is suppressed) were inferior to those in AF. Besides the moderating influence of the salt cation on ionic retention, it is likely that salt buffers improve peak shape due to the increased ionic strength of the mobile phase and its impact on the formation of the water layer on the column surface.

  3. Photodegradation of Mercaptopropionic Acid- and Thioglycollic Acid-Capped CdTe Quantum Dots in Buffer Solutions.

    PubMed

    Miao, Yanping; Yang, Ping; Zhao, Jie; Du, Yingying; He, Haiyan; Liu, Yunshi

    2015-06-01

    CdTe quantum dots (QDs) were synthesized by 3-mercaptopropionic acid (MPA) and thioglycollic acid (TGA) as capping agents. It is confirmed that TGA and MPA molecules were attached on the surface of the QDs using Fourier transform infrared (FT-IR) spectra. The movement of the QDs in agarose gel electrophoresis indicated that MPA-capped CdTe QDs had small hydrodynamic diameter. The photoluminescence (PL) intensity of TGA-capped QDs is higher than that of MPA-capped QDs at same QD concentration because of the surface passivation of TGA. To systemically investigate the photodegradation, CdTe QDs with various PL peak wavelengths were dispersed in phosphate buffered saline (PBS) and Tris-borate-ethylenediaminetetraacetic acid (TBE) buffer solutions. It was found that the PL intensity of the QDs in PBS decreased with time. The PL peak wavelengths of the QDs in PBS solutions remained unchanged. As for TGA-capped CdTe QDs, the results of PL peak wavelengths in TBE buffer solutions indicated that S(2-) released by TGA attached to Cd(2+) and formed CdS-like clusters layer on the surface of aqueous CdTe QDs. In addition, the number of TGA on the CdTe QDs surface was more than that of MPA. When the QDs were added to buffer solutions, agents were removed from the surface of CdTe QDs, which decreased the passivation of agents thus resulted in photodegradation of CdTe QDs in buffer solutions.

  4. Poly(N-vinylimidazole) gels as insoluble buffers that neutralize acid solutions without dissolving.

    PubMed

    Horta, Arturo; Piérola, Inés F

    2009-04-01

    Typical buffers are solutions containing weak acids or bases. If these groups were anchored to insoluble gels, what would be their behavior? Simple thermodynamics is used to calculate the pH in two-phase systems that contain the weak acid or base fixed to only one of the phases and is absent in the other. The experimental reference of such systems are pH sensitive hydrogels and heterogeneous systems of biological interest. It is predicted that a basic hydrogel immersed in slightly acidic solutions should absorb the acid and leave the external solution exactly neutral (pH 7). This is in accordance with experimental results of cross-linked poly(N-vinylimidazole). The pH 7 cannot be obtained if the system were homogeneous; the confinement of the weak base inside the gel phase is a requisite for this neutral pH in the external solution. The solution inside the gel is regulated to a much higher pH, which has important implications in studies on chemical reactions and physical processes taking place inside a phase insoluble but in contact with a solution. PMID:19245223

  5. Thermodynamic characteristics of the interaction between nicotinic acid and phenylalanine in an aqueous buffer solution at 298 K

    NASA Astrophysics Data System (ADS)

    Badelin, V. G.; Tyunina, E. Yu.; Mezhevoi, I. N.; Tarasova, G. N.

    2013-08-01

    The interaction between L-phenylalanine and nicotinic acid is studied by solution calorimetry in an aqueous buffer solution (pH 7.35) at different ratios of the reagents. Experimental data on the enthalpy of dissolution of amino acid in the buffer solution of nicotinic acid at 298.15 K are calculated. The values of thermodynamic parameters for the complexation of L-phenylalanine with nicotinic acid are calculated. It is shown that the formation of a 1: 2 molecular complex is stabilized by the entropy factor due to the dominant role of the dehydration effect of initial reagents.

  6. Improving impurities clearance by amino acids addition to buffer solutions for chromatographic purifications of monoclonal antibodies.

    PubMed

    Ishihara, Takashi; Hosono, Mareto

    2015-07-15

    The performance of amino acids in Protein A affinity chromatography, anion exchange chromatography and cation exchange chromatography for monoclonal antibody purification was investigated. Glycine, threonine, arginine, glutamate, and histidine were used as buffer components in the equilibration, washing, and elution steps of these chromatographies. Improved clearance of impurity, high molecular weight species (HMW) and host cell proteins (HCP) was observed in the purification processes when using the amino acids as base-buffer constituents, additives or eluents compared with that of buffers without these amino acids. In addition, we designed a buffer system in which the mobile phases were composed of only a single amino acid, histidine, and applied it to the above three chromatographies. Effective HMW and HCP clearance was also obtained in this manner. These results suggest that amino acids may enhance impurity clearance during the purification of monoclonal antibodies. PMID:26057847

  7. Simultaneous pollutant removal and electricity generation in denitrifying microbial fuel cell with boric acid-borate buffer solution.

    PubMed

    Chen, Gang; Zhang, Shaohui; Li, Meng; Wei, Yan

    2015-01-01

    A double-chamber denitrifying microbial fuel cell (MFC), using boric acid-borate buffer solution as an alternative to phosphate buffer solution, was set up to investigate the influence of buffer solution concentration, temperature and external resistance on electricity generation and pollutant removal efficiency. The result revealed that the denitrifying MFC with boric acid-borate buffer solution was successfully started up in 51 days, with a stable cell voltage of 205.1 ± 1.96 mV at an external resistance of 50 Ω. Higher concentration of buffer solution favored nitrogen removal and electricity generation. The maximum power density of 8.27 W/m(3) net cathodic chamber was obtained at a buffer solution concentration of 100 mmol/L. An increase in temperature benefitted electricity generation and nitrogen removal. A suitable temperature for this denitrifying MFC was suggested to be 25 °C. Decreasing the external resistance favored nitrogen removal and organic matter consumption by exoelectrogens. PMID:25768227

  8. Simultaneous pollutant removal and electricity generation in denitrifying microbial fuel cell with boric acid-borate buffer solution.

    PubMed

    Chen, Gang; Zhang, Shaohui; Li, Meng; Wei, Yan

    2015-01-01

    A double-chamber denitrifying microbial fuel cell (MFC), using boric acid-borate buffer solution as an alternative to phosphate buffer solution, was set up to investigate the influence of buffer solution concentration, temperature and external resistance on electricity generation and pollutant removal efficiency. The result revealed that the denitrifying MFC with boric acid-borate buffer solution was successfully started up in 51 days, with a stable cell voltage of 205.1 ± 1.96 mV at an external resistance of 50 Ω. Higher concentration of buffer solution favored nitrogen removal and electricity generation. The maximum power density of 8.27 W/m(3) net cathodic chamber was obtained at a buffer solution concentration of 100 mmol/L. An increase in temperature benefitted electricity generation and nitrogen removal. A suitable temperature for this denitrifying MFC was suggested to be 25 °C. Decreasing the external resistance favored nitrogen removal and organic matter consumption by exoelectrogens.

  9. The erosion kinetics of conventional and resin-modified glass-ionomer luting cements in acidic buffer solutions.

    PubMed

    Hazar-Yoruc, Binnaz; Bavbek, Andac Barkin; Özcan, Mutlu

    2012-01-01

    This study investigated the erosion kinetics of conventional and resin-modified glass-ionomer luting cements in acidic buffer solutions as a function of time. Disc shaped specimens were prepared from conventional (Ketac-Cem: KTC) and resin-modified glass ionomer cements (Fuji Plus: FP) and immersed in three acidic buffer solutions (0.01 M) namely, acetic acid/sodium acetate (AA(B)), lactic acid/sodium lactate (LA(B)) and citric acid/sodium citrate (CA(B)) with a constant pH of 4.1 and stored for 1, 8, 24, 48, 80, 120 and 168 h. F concentration was determined using ion-specific electrode. Si, Ca and Al concentrations were determined by atomic absorption spectroscopy. Ca, Al, Si and F solubility rates in both FP and KTC were the highest in CA(B) solution. The erosion rates of both FP and KTC in all buffer solutions increased as a function of immersion time. The amount of F eluted from FP was more than that of KTC. The total amount of elements released from FP was less than KTC in all solutions. PMID:23207217

  10. Nonclinical safety evaluation of boric acid and a novel borate-buffered contact lens multi-purpose solution, Biotrue™ multi-purpose solution.

    PubMed

    Lehmann, David M; Cavet, Megan E; Richardson, Mary E

    2010-12-01

    Multipurpose solutions (MPS) often contain low concentrations of boric acid as a buffering agent. Limited published literature has suggested that boric acid and borate-buffered MPS may alter the corneal epithelium; an effect attributed to cytotoxicity induced by boric acid. However, this claim has not been substantiated. We investigated the effect of treating cells with relevant concentrations of boric acid using two cytotoxicity assays, and also assessed the impact of boric acid on corneal epithelial barrier function by measuring TEER and immunostaining for tight junction protein ZO-1 in human corneal epithelial cells. Boric acid was also assessed in an in vivo ocular model when administered for 28 days. Additionally, we evaluated Biotrue multi-purpose solution, a novel borate-buffered MPS, alone and with contact lenses for ocular compatibility in vitro and in vivo. Boric acid passed both cytotoxicity assays and did not alter ZO-1 distribution or corneal TEER. Furthermore, boric acid was well-tolerated on-eye following repeated administration in a rabbit model. Finally, Biotrue multi-purpose solution demonstrated good ocular biocompatibility both in vitro and in vivo. This MPS was not cytotoxic and was compatible with the eye when administered alone and when evaluated with contact lenses. We demonstrate that boric acid and a borate-buffered MPS is compatible with the ocular environment. Our findings provide evidence that ocular effects reported for some borate-buffered MPS may be incorrectly attributed to boric acid and are more likely a function of the unique combination of ingredients in the MPS formulation tested.

  11. Electrodialysis operation with buffer solution

    DOEpatents

    Hryn, John N.; Daniels, Edward J.; Krumdick, Greg K.

    2009-12-15

    A new method for improving the efficiency of electrodialysis (ED) cells and stacks, in particular those used in chemical synthesis. The process entails adding a buffer solution to the stack for subsequent depletion in the stack during electrolysis. The buffer solution is regenerated continuously after depletion. This buffer process serves to control the hydrogen ion or hydroxide ion concentration so as to protect the active sites of electrodialysis membranes. The process enables electrodialysis processing options for products that are sensitive to pH changes.

  12. In situ ellipsometric investigation of stainless steel corrosion behavior in buffered solutions with amino acids

    NASA Astrophysics Data System (ADS)

    Vinnichenko, M. V.; Pham, M. T.; Chevolleau, T.; Poperenko, L. V.; Maitz, M. F.

    2003-02-01

    The corrosion of metals is associated both with a release of ions and changes in optical surface properties. In this study, these two effects were correlated by a potentiodynamic corrosion test and in situ probing of the surface by ellipsometry. The studies were carried out with stainless steel (SS) AISI 304 and 316 in phosphate buffered saline (PBS) and in Dulbecco's modified minimal essential medium (DMEM) at pH 7.4. In both media, 304 steel is more susceptible to corrosion than 316 grade. The 316 steel shows a higher corrosion potential and higher corrosion current density in PBS than in DMEM, for 304 steel this behavior is vice versa. Ellipsometry demonstrated a higher sensitivity than potentiodynamics to surface modification in the cathodic area. In DMEM the removal of a surface layer at negative potential and a further repassivation with increasing potential was characteristic. In PBS a surface layer started to grow immediately. X-ray photoelectron spectra of this layer formed in PBS are consistent with iron phosphate. Its formation is inhibited in DMEM; the presence of amino acids is discussed as the reason.

  13. Thermodynamical characteristics of the reaction of pyridoxal-5'-phosphate with L-amino acids in aqueous buffer solution

    NASA Astrophysics Data System (ADS)

    Barannikov, V. P.; Badelin, V. G.; Venediktov, E. A.; Mezhevoi, I. N.; Guseinov, S. S.

    2011-01-01

    The reaction of pyridoxal-5'-phosphate with L-isomers of alanine, lysine, arginine, aspartic acid, glutamic acid, and glycine in phosphate buffer solution was studied by absorption spectroscopy and the calorimetry of dissolution at physiological acidity of the medium (pH 7.35). The formation constants of Schiff bases during reactions and changes in Gibbs energy, enthalpy, and entropy were determined. It was shown that the formation constant of the Schiff base and its spectral properties depend on the nature of the bound amino acid. The progress of the reaction with a majority of amino acids is governed by the entropy factor due to the predominant role of the dehydration effect of the reaction center of amino acids during chemical reactions. The intramolecular electrostatic interaction of an ionized phosphate group with the positively charged amino group on the end of the chain of amino acid residue stabilizes the Schiff bases formed by lysine and arginine. The extinction coefficient of the base, equilibrium constant, and the exothermic effect of the reaction then increase. The excess negative charge on the end of the chain of amino acid residues of aspartic and glutamic acids destabilizes the molecule of the Schiff base. In this case, the equilibrium constant decreases and the endothermic effect of the reaction increases.

  14. Matching phosphate and maleate buffer systems for dissolution of weak acids: Equivalence in terms of buffer capacity of bulk solution or surface pH?

    PubMed

    Cristofoletti, Rodrigo; Dressman, Jennifer B

    2016-06-01

    The development of in vitro dissolution tests able to anticipate the in vivo fate of drug products has challenged pharmaceutical scientists over time, especially in the case of ionizable compounds. In the seminal model proposed by Mooney et al. thirty-five years ago, the pH at the solid-liquid interface (pH0) was identified as a key parameter in predicting dissolution rate. In the current work it is demonstrated that the in vitro dissolution of the weak acid ibuprofen in maleate and phosphate buffer systems is a function of the pH0, which in turn is affected by properties of the drug and the medium. The reported pH0 for ibuprofen dissolution in bicarbonate buffer, the predominant buffer species in the human small intestine under fasting conditions, can be achieved by reducing the phosphate buffer concentration to 5.0mM or the maleate buffer concentration to 2.2mM. Using this approach to identify the appropriate buffer/buffer capacity combination for in vitro experiments in FaSSIF-type media, it would be possible to increase the physiological relevance of this important biopharmaceutics tool. However, the necessity of monitoring and adjusting the bulk pH during the experiments carried out in 5.0mM phosphate or 2.2mM maleate buffers must also be taken into consideration. PMID:27032508

  15. Matching phosphate and maleate buffer systems for dissolution of weak acids: Equivalence in terms of buffer capacity of bulk solution or surface pH?

    PubMed

    Cristofoletti, Rodrigo; Dressman, Jennifer B

    2016-06-01

    The development of in vitro dissolution tests able to anticipate the in vivo fate of drug products has challenged pharmaceutical scientists over time, especially in the case of ionizable compounds. In the seminal model proposed by Mooney et al. thirty-five years ago, the pH at the solid-liquid interface (pH0) was identified as a key parameter in predicting dissolution rate. In the current work it is demonstrated that the in vitro dissolution of the weak acid ibuprofen in maleate and phosphate buffer systems is a function of the pH0, which in turn is affected by properties of the drug and the medium. The reported pH0 for ibuprofen dissolution in bicarbonate buffer, the predominant buffer species in the human small intestine under fasting conditions, can be achieved by reducing the phosphate buffer concentration to 5.0mM or the maleate buffer concentration to 2.2mM. Using this approach to identify the appropriate buffer/buffer capacity combination for in vitro experiments in FaSSIF-type media, it would be possible to increase the physiological relevance of this important biopharmaceutics tool. However, the necessity of monitoring and adjusting the bulk pH during the experiments carried out in 5.0mM phosphate or 2.2mM maleate buffers must also be taken into consideration.

  16. High-quality fiber fabrication in buffered hydrofluoric acid solution with ultrasonic agitation.

    PubMed

    Zhong, Nianbing; Liao, Qiang; Zhu, Xun; Wang, Yongzhong; Chen, Rong

    2013-03-01

    An etching method for preparing high-quality fiber-optic sensors using a buffered etchant with ultrasonic agitation is proposed. The effects of etching conditions on the etch rate and surface morphology of the etched fibers are investigated. The effect of surface roughness is discussed on the fibers' optical properties. Linear etching behavior and a smooth fiber surface can be repeatedly obtained by adjusting the ultrasonic power and etchant pH. The fibers' spectral quality is improved as the ratio of the pit depth to size decreases, and the fibers with smooth surfaces are more sensitive to a bacterial suspension than those with rough surfaces.

  17. Rapid demineralization in acidic buffers.

    PubMed

    Eggert, F M; Germain, J P

    1979-01-22

    The demineralization of routine histological specimens in buffers of weakly ionized organic acids, unbuffered formic acid, and EDTA was investigated. The rate of demineralization was measured by a chemical method and from radiographs. Lactate-containing buffers and buffers of formic acid with its potassium salt were more rapid in effect than any other agent. Acidic buffers and unbuffered formic acid produced rapid diffuse demineralization with secondary precipitation of calcium salts. Preservation of dental enamel in such buffers resulted from the significantly slower rate of enamel demineralization than that for bone and dentine. In rapid demineralizing agents the secondary salts were quickly redissolved while in slow buffers these salts persisted. Multivalent ions such as citrate and maleate slowed the rate of demineralization, and a citrate-containing buffer was the slowest of all the agents tested. Demineralization in EDTA exhibited a different pattern with the establishment of a well-defined front of demineralization without apparent reprecipitation. EDTA attacked enamel, bone and dentine at the same rate. An attempt was made to relate the observed rates of demineralization to current theories of the demineralization process.

  18. An evaluation of MES (2(N-Morpholino)ethanesulfonic acid) and Amberlite IRC-50 as pH buffers for nutrient solution studies

    NASA Technical Reports Server (NTRS)

    Bugbee, B. G.; Salisbury, F. B.

    1985-01-01

    All buffering agents used to stabilize pH in hydroponic research have disadvantages. Inorganic buffers are absorbed and may become phytotoxic. Solid carbonate salts temporarily mitigate decreasing pH but provide almost no protection against increasing pH, and they alter nutrient absorption. Exchange resins are more effective, but we find that they remove magnesium and manganese from solution. We have tested 2(N-Morpholino)ethanesulfonic acid (MES) as a buffering agent at concentrations of 1 and 10 mol m-3 (1 and 10 mM) with beans, corn, lettuce, tomatoes, and wheat. MES appears to be biologically inert and does not interact significantly with other solution ions. Relative growth rates among controls and MES treatments were nearly identical for each species during the trial period. The pH was stabilized by 1 mol m-3 MES. This buffer warrants further consideration in nutrient research.

  19. Comparative Evaluation of Shear Bond Strength of Luting Cements to Different Core Buildup Materials in Lactic Acid Buffer Solution

    PubMed Central

    Patil, Siddharam M.; Desai, Raviraj G.; Arabbi, Kashinath C.; Prakash, Ved

    2015-01-01

    Aim and Objectives The core buildup material is used to restore badly broken down tooth to provide better retention for fixed restorations. The shear bond strength of a luting agent to core buildup is one of the crucial factors in the success of the cast restoration. The aim of this invitro study was to evaluate and compare the shear bond strength of luting cements with different core buildup materials in lactic acid buffer solution. Materials and Methods Two luting cements {Traditional Glass Ionomer luting cement (GIC) and Resin Modified Glass Ionomer luting cement (RMGIC)} and five core buildup materials {Silver Amalgam, Glass ionomer (GI), Glass Ionomer Silver Reinforced (GI Silver reinforced), Composite Resin and Resin Modified Glass Ionomer(RMGIC)} were selected for this study. Total 100 specimens were prepared with 20 specimens for each core buildup material using a stainless steel split metal die. Out of these 20 specimens, 10 specimens were bonded with each luting cement. All the bonded specimens were stored at 370c in a 0.01M lactic acid buffer solution at a pH of 4 for 7days. Shear bond strength was determined using a Universal Testing Machine at a cross head speed of 0.5mm/min. The peak load at fracture was recorded and shear bond strength was calculated. The data was statistically analysed using Two-way ANOVA followed by HOLM-SIDAK method for pair wise comparison at significance level of p<0.05. Results Two-Way ANOVA showed significant differences in bond strength of the luting cements (p<0.05) and core materials (p<0.05) and the interactions (p<0.05). Pairwise comparison of luting cements by HOLM-SIDAK test, showed that the RMGIC luting cement had higher shear bond strength values than Traditional GIC luting cement for all the core buildup materials. RMGIC core material showed higher bond strength values followed by Composite resin, GI silver reinforced, GI and silver amalgam core materials for both the luting agents. Conclusion Shear bond strength of

  20. Acid neutralizing processes in an alpine watershed front range, Colorado, U.S.A.-1: Buffering capacity of dissolved organic carbon in soil solutions

    USGS Publications Warehouse

    Iggy, Litaor M.; Thurman, E.M.

    1988-01-01

    Soil interstitial waters in the Green Lakes Valley, Front Range, Colorado were studied to evaluate the capacity of the soil system to buffer acid deposition. In order to determine the contribution of humic substances to the buffering capacity of a given soil, dissolved organic carbon (DOC) and pH of the soil solutions were measured. The concentration of the organic anion, Ai-, derived from DOC at sample pH and the concentration of organic anion, Ax- at the equivalence point were calculated using carboxyl contents from isolated and purified humic material from soil solutions. Subtracting Ax- from Ai- yields the contribution of humic substances to the buffering capacity (Aequiv.-). Using this method, one can evaluate the relative contribution of inorganic and organic constituents to the acid neutralizing capacity (ANC) of the soil solutions. The relative contribution of organic acids to the overall ANC was found to be extremely important in the alpine wetland (52%) and the forest-tundra ecotone (40%), and somewhat less important in the alpine tundra sites (20%). A failure to recognize the importance of organic acids in soil solutions to the ANC will result in erroneous estimates of the buffering capacity in the alpine environment of the Front Range, Colorado. ?? 1988.

  1. Thermodynamic characteristics of molecular interactions between L-tryptophan and nicotinic acid and uracyl in aqueous buffer solutions at 298 K

    NASA Astrophysics Data System (ADS)

    Badelin, V. G.; Tyunina, E. Yu.; Mezhevoi, I. N.; Tarasova, G. N.

    2015-12-01

    The interaction between L-tryptophan (Trp) and nicotinic acid (NA) and uracyl (Ur) in aqueous buffer solutions (pH 7.35) at different ratios of reagents is studied via the calorimetry of dissolution. The enthalpies of dissolution of the amino acid in the buffer solutions of the ligands at 298.15 K are obtained. The stoichiometric compositions of the complexes being formed and binding constants have been determined. The values of the thermodynamic characteristics for the complex formation of L-tryptophan with nicotinic acid and uracyl are calculated. It is shown that the formation of molecular complexes with 1 : 2 composition is stabilized by the entropy factor for the Trp-NA system, and by the enthalpy factor for the Trp-Ur system.

  2. Comparison of Buffer Effect of Different Acids During Sandstone Acidizing

    NASA Astrophysics Data System (ADS)

    Umer Shafiq, Mian; Khaled Ben Mahmud, Hisham; Hamid, Mohamed Ali

    2015-04-01

    The most important concern of sandstone matrix acidizing is to increase the formation permeability by removing the silica particles. To accomplish this, the mud acid (HF: HCl) has been utilized successfully for many years to stimulate the sandstone formations, but still it has many complexities. This paper presents the results of laboratory investigations of different acid combinations (HF: HCl, HF: H3PO4 and HF: HCOOH). Hydrofluoric acid and fluoboric acid are used to dissolve clays and feldspar. Phosphoric and formic acids are added as a buffer to maintain the pH of the solution; also it allows the maximum penetration of acid into the core sample. Different tests have been performed on the core samples before and after the acidizing to do the comparative study on the buffer effect of these acids. The analysis consists of permeability, porosity, color change and pH value tests. There is more increase in permeability and porosity while less change in pH when phosphoric and formic acids were used compared to mud acid. From these results it has been found that the buffer effect of phosphoric acid and formic acid is better than hydrochloric acid.

  3. Spectrophotometric determination of the protolytic dissociation constants of the new chromogenic reagent "palladiazo"-I Investigations with sodium hydroxide, perchloric acid and different aqueous buffer solutions.

    PubMed

    Pérez-Butsamante, J A; Burriel-Martí, F

    1971-02-01

    The "palladiazo" reagent has been subjected to a detailed spectrophotometric investigation in concentrated perchloric acid, different aqueous buffers and concentrated sodium hydroxide solutions. K(1)-K(10) and (1)-(10) values corresponding to the instability constants of the protolytic equilibria involved and to the molar absorptivities at 540 and 630 run of the different proton complex species of the system have been calculated by a number of analytical and graphical spectrophotometric methods. Special attention has been paid to the study of the complicated phenomena implied by the interaction of the reagent with perchloric acid, which has been shown to give rise to alteration of the initial isomeric composition of the reagent and to the formation of addition and/or oxidation products derived from side-reactions undergone by the reagent with the medium. All the instability constants and molar absorptivities, which have been determined by several methods, are tabulated for comparison.

  4. DISTRIBUTION OF LANTHANIDE AND ACTINIDE ELEMENTS BETWEEN BIS-(2-ETHYLHEXYL)PHOSPHORIC ACID AND BUFFERED LACTATE SOLUTIONS CONTAINING SELECTED COMPLEXANTS

    SciTech Connect

    Rudisill, Tracy S.; Diprete, David P.; Thompson, Major C.

    2013-04-15

    With the renewed interest in the closure of the nuclear fuel cycle, the TALSPEAK process is being considered for the separation of Am and Cm from the lanthanide fission products in a next generation reprocessing plant. However, an efficient separation requires tight control of the pH which likely will be difficult to achieve on a large scale. To address this issue, we measured the distribution of lanthanide and actinide elements between aqueous and organic phases in the presence of complexants which were potentially less sensitive to pH control than the diethylenetriaminepentaacetic (DTPA) used in the process. To perform the extractions, a rapid and accurate method was developed for measuring distribution coefficients based on the preparation of lanthanide tracers in the Savannah River National Laboratory neutron activation analysis facility. The complexants tested included aceto-, benzo-, and salicylhydroxamic acids, N,N,N',N'-tetrakis(2-pyridylmethyl)ethylenediamine (TPEN), and ammonium thiocyanate (NH{sub 4}SCN). The hydroxamic acids were the least effective of the complexants tested. The separation factors for TPEN and NH{sub 4}SCN were higher, especially for the heaviest lanthanides in the series; however, no conditions were identified which resulted in separations factors which consistently approached those measured for the use of DTPA.

  5. On the Preparation of Buffer Solutions.

    ERIC Educational Resources Information Center

    Thomson, Bruce M.; Kessick, Michael A.

    1981-01-01

    Presents a method, suitable for use on programmable calculators, which allows calculation of the pH and ionic strength (I) of a mixed solution of salts of an acid or amounts necessary to produce a solution of a particular pH and I. Includes limitations when using the calculations described. (SK)

  6. Antimicrobial activity of borate-buffered solutions.

    PubMed Central

    Houlsby, R D; Ghajar, M; Chavez, G O

    1986-01-01

    A minimal salts medium adjusted to physiological pH and osmolality was buffered with either 0.3% phosphate or 1.2% borate and evaluated for antimicrobial activity. The borate-buffered medium, either with or without a carbon source, exhibited significant antimicrobial activity against 15 Pseudomonas strains, 12 strains of enteric bacteria, and 7 strains of staphylococci. The borate-buffered system appears suitable for use as a generic vehicle for ophthalmic pharmaceutical agents. PMID:3729341

  7. Buffer-free therapeutic antibody preparations provide a viable alternative to conventionally buffered solutions: from protein buffer capacity prediction to bioprocess applications.

    PubMed

    Bahrenburg, Sven; Karow, Anne R; Garidel, Patrick

    2015-04-01

    Protein therapeutics, including monoclonal antibodies (mAbs), have significant buffering capacity, particularly at concentrations>50 mg/mL. This report addresses pH-related issues critical to adoption of self-buffered monoclonal antibody formulations. We evaluated solution conditions with protein concentrations ranging from 50 to 250 mg/mL. Samples were both buffer-free and conventionally buffered with citrate. Samples were non-isotonic or adjusted for isotonicity with NaCl or trehalose. Studies included accelerated temperature stability tests, shaking stability studies, and pH changes in infusion media as protein concentrate is added. We present averaged buffering slopes of capacity that can be applied to any mAb and present a general method for calculating buffering capacity of buffer-free, highly concentrated antibody liquid formulations. In temperature stability tests, neither buffer-free nor conventionally buffered solution conditions showed significant pH changes. Conventionally buffered solutions showed significantly higher opalescence than buffer-free ones. In general, buffer-free solution conditions showed less aggregation than conventionally buffered solutions. Shaking stability tests showed no differences between buffer-free and conventionally buffered solutions. "In-use" preparation experiments showed that pH in infusion bag medium can rapidly approximate that of self-buffered protein concentrate as concentrate is added. In summary, the buffer capacity of proteins can be predicted and buffer-free therapeutic antibody preparations provide a viable alternative to conventionally buffered solutions. PMID:25641961

  8. Buffer-free therapeutic antibody preparations provide a viable alternative to conventionally buffered solutions: from protein buffer capacity prediction to bioprocess applications.

    PubMed

    Bahrenburg, Sven; Karow, Anne R; Garidel, Patrick

    2015-04-01

    Protein therapeutics, including monoclonal antibodies (mAbs), have significant buffering capacity, particularly at concentrations>50 mg/mL. This report addresses pH-related issues critical to adoption of self-buffered monoclonal antibody formulations. We evaluated solution conditions with protein concentrations ranging from 50 to 250 mg/mL. Samples were both buffer-free and conventionally buffered with citrate. Samples were non-isotonic or adjusted for isotonicity with NaCl or trehalose. Studies included accelerated temperature stability tests, shaking stability studies, and pH changes in infusion media as protein concentrate is added. We present averaged buffering slopes of capacity that can be applied to any mAb and present a general method for calculating buffering capacity of buffer-free, highly concentrated antibody liquid formulations. In temperature stability tests, neither buffer-free nor conventionally buffered solution conditions showed significant pH changes. Conventionally buffered solutions showed significantly higher opalescence than buffer-free ones. In general, buffer-free solution conditions showed less aggregation than conventionally buffered solutions. Shaking stability tests showed no differences between buffer-free and conventionally buffered solutions. "In-use" preparation experiments showed that pH in infusion bag medium can rapidly approximate that of self-buffered protein concentrate as concentrate is added. In summary, the buffer capacity of proteins can be predicted and buffer-free therapeutic antibody preparations provide a viable alternative to conventionally buffered solutions.

  9. Reductive dechlorination of carbon tetrachloride using buffered alkaline ascorbic acid.

    PubMed

    Lin, Ya-Ting; Liang, Chenju

    2015-10-01

    Alkaline ascorbic acid (AA) was recently discovered as a novel in-situ chemical reduction (ISCR) reagent for remediating chlorinated solvents in the subsurface. For this ISCR process, the maintenance of an alkaline pH is essential. This study investigated the possibility of the reduction of carbon tetrachloride (CT) using alkaline AA solution buffered by phosphate and by NaOH. The results indicated that CT was reduced by AA, and chloroform (CF) was a major byproduct at a phosphate buffered pH of 12. However, CT was completely reduced by AA in 2M NaOH without CF formation. In the presence of iron/soil minerals, iron could be reduced by AA and Fe(2+) tends to precipitate on the mineral surface to accelerate CT degradation. A simultaneous transfer of hydrogenolysis and dichloroelimination would occur under phosphate buffered pH 12. This implies that a high alkaline environment is a crucial factor for maintaining the dominant pathway of two electron transfer from dianionic AA to dehydroascorbic acid, and to undergo dichloroelimination of CT. Moreover, threonic acid and oxalic acid were identified to be the major AA decomposition products in alkaline solutions.

  10. Electrochemical behaviour of silver in borate buffer solutions

    NASA Astrophysics Data System (ADS)

    Zaky, Ayman M.; Assaf, Fawzi H.; Abd El Rehim, Sayed S.; Mohamed, Basheer M.

    2004-01-01

    The electrochemical behaviour of Ag in aqueous 0.15 M borax and 0.15 M boric acid buffer solution was studied under various conditions using cyclic voltammetry and potentiostatic techniques. It was found that the anodic polarization curve of Ag in borate buffer solution was characterized by the appearance of two potential regions, active and passive, prior to the oxygen evolution reaction. The active potential region was characterized by the appearance of three anodic peaks, the first two peaks A 1 and A 2 correspond to the oxidation of Ag and formation of [Ag(OH) 2] - soluble compound and a passive film of Ag 2O on the electrode surface. The third anodic peak corresponds to the conversion of both [Ag(OH) 2] - and Ag 2O to Ag 2O 2. X-ray diffraction patterns confirmed the existence of Ag 2O and Ag 2O 2 passive layers on the electrode surface potentiodynamically polarized up to 800 mV. Potentiostatic current transient measurements showed that the formation of Ag 2O and Ag 2O 2 involves a nucleation and growth mechanism under diffusion control.

  11. Differential effect of buffering agents on the crystallization of gemcitabine hydrochloride in frozen solutions.

    PubMed

    Patel, Mehulkumar; Munjal, Bhushan; Bansal, Arvind K

    2014-08-25

    The purpose of this study was to evaluate the differential effect of buffering agents on the crystallization of gemcitabine hydrochloride (GHCl) in frozen solutions. Four buffering agents, viz. citric acid (CA), malic acid (MA), succinic acid (SA) and tartaric acid (TA) were selected and their effect on GHCl crystallization was monitored using standard DSC and low temperature XRD. Onset of GHCl crystallization during heating run in DSC was measured to compare the differential effect of buffering agents. Glass transition temperature (Tg'), unfrozen water content in the freeze concentrate and crystallization propensity of the buffering agents was also determined for mechanistic understanding of the underlying effects. CA and MA inhibited while SA facilitated crystallization of GHCl even at 25 mM concentration. Increasing the concentration enhanced their effect. However, TA inhibited GHCl crystallization at concentrations <100mM and facilitated it at concentrations ≥100 mM. Lyophilization of GHCl with either SA or TA yielded elegant cakes, while CA and MA caused collapse. Tg' failed to explain the inhibitory effects of CA, MA and TA as all buffering agents lowered the Tg' of the system. Differential effect of buffering agents on GHCl crystallization could be explained by consideration of two opposing factors: (i) their own crystallization tendency and (ii) unfrozen water content in the freeze concentrate. In conclusion, it was established that API crystallization in frozen solution is affected by the type and concentration of the buffering agents.

  12. Differential effect of buffering agents on the crystallization of gemcitabine hydrochloride in frozen solutions.

    PubMed

    Patel, Mehulkumar; Munjal, Bhushan; Bansal, Arvind K

    2014-08-25

    The purpose of this study was to evaluate the differential effect of buffering agents on the crystallization of gemcitabine hydrochloride (GHCl) in frozen solutions. Four buffering agents, viz. citric acid (CA), malic acid (MA), succinic acid (SA) and tartaric acid (TA) were selected and their effect on GHCl crystallization was monitored using standard DSC and low temperature XRD. Onset of GHCl crystallization during heating run in DSC was measured to compare the differential effect of buffering agents. Glass transition temperature (Tg'), unfrozen water content in the freeze concentrate and crystallization propensity of the buffering agents was also determined for mechanistic understanding of the underlying effects. CA and MA inhibited while SA facilitated crystallization of GHCl even at 25 mM concentration. Increasing the concentration enhanced their effect. However, TA inhibited GHCl crystallization at concentrations <100mM and facilitated it at concentrations ≥100 mM. Lyophilization of GHCl with either SA or TA yielded elegant cakes, while CA and MA caused collapse. Tg' failed to explain the inhibitory effects of CA, MA and TA as all buffering agents lowered the Tg' of the system. Differential effect of buffering agents on GHCl crystallization could be explained by consideration of two opposing factors: (i) their own crystallization tendency and (ii) unfrozen water content in the freeze concentrate. In conclusion, it was established that API crystallization in frozen solution is affected by the type and concentration of the buffering agents. PMID:24836665

  13. Use of buffered hypochlorite solution for disinfecting fibrescopes.

    PubMed Central

    Coates, D; Death, J E

    1982-01-01

    The possible use of sodium hypochlorite solution buffered to pH 7.6 and containing 100 ppm available chlorine (avCl) for disinfecting fibrescopes was investigated. A flexible fibrescope experimentally contaminated with Pseudomonas putida, Mycobacterium fortuitum, or Bacillus subtilis spores was effectively disinfected within 10 m in repeatedly and without any observable adverse effect on the instrument. The corrosive nature of buffered hypochlorite was investigated by immersing various fibrescope components and metal wires in solutions of different strength for long periods and examining them for damage. Stainless steel, platinum, glass, Teflon, polythene and epoxy resin were apparently unaffected whereas polyurethane, rubber and other metals tested were damaged to different extents. Buffered hypochlorite solutions may have many applications pertaining to the disinfection of items which are either thermolabile or require rapid effective disinfection. PMID:6802880

  14. The boundary lubrication of chemically grafted and cross-linked hyaluronic acid in phosphate buffered saline and lipid solutions measured by the surface forces apparatus.

    PubMed

    Yu, Jing; Banquy, Xavier; Greene, George W; Lowrey, Daniel D; Israelachvili, Jacob N

    2012-01-31

    High molecular weight hyaluronic acid (HA) is present in articular joints and synovial fluid at high concentrations; yet despite numerous studies, the role of HA in joint lubrication is still not clear. Free HA in solution does not appear to be a good lubricant, being negatively charged and therefore repelled from most biological, including cartilage, surfaces. Recent enzymatic experiments suggested that mechanically or physically (rather than chemically) trapped HA could function as an "adaptive" or "emergency" boundary lubricant to eliminate wear damage in shearing cartilage surfaces. In this work, HA was chemically grafted to a layer of self-assembled amino-propyl-triethoxy-silane (APTES) on mica and then cross-linked. The boundary lubrication behavior of APTES and of chemically grafted and cross-linked HA in both electrolyte and lipid 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) solutions was tested with a surface forces apparatus (SFA). Despite the high coefficient of friction (COF) of μ ≈ 0.50, the chemically grafted HA gel significantly improved the lubrication behavior of HA, particularly the wear resistance, in comparison to free HA. Adding more DOPC lipid to the solution did not improve the lubrication of the chemically grafted and cross-linked HA layer. Damage of the underlying mica surface became visible at higher loads (pressure >2 MPa) after prolonged sliding times. It has generally been assumed that damage caused by or during sliding, also known as "abrasive friction", which is the main biomedical/clinical/morphological manifestation of arthritis, is due to a high friction force and, therefore, a large COF, and that to prevent surface damage or wear (abrasion) one should therefore aim to reduce the COF, which has been the traditional focus of basic research in biolubrication, particularly in cartilage and joint lubrication. Here we combine our results with previous ones on grafted and cross-linked HA on lipid bilayers, and lubricin

  15. Internal acid buffering in San Joaquin Valley fog drops and its influence on aerosol processing

    NASA Astrophysics Data System (ADS)

    Collett, Jeffrey L.; Hoag, Katherine J.; Rao, Xin; Pandis, Spyros N.

    Although several chemical pathways exist for S(IV) oxidation in fogs and clouds, many are self-limiting: as sulfuric acid is produced and the drop pH declines, the rates of these pathways also decline. Some of the acid that is produced can be buffered by uptake of gaseous ammonia. Additional internal buffering can result from protonation of weak and strong bases present in solution. Acid titrations of high pH fog samples (median pH=6.49) collected in California's San Joaquin Valley reveal the presence of considerable internal acid buffering. In samples collected at a rural location, the observed internal buffering could be nearly accounted for based on concentrations of ammonia and bicarbonate present in solution. In samples collected in the cities of Fresno and Bakersfield, however, significant additional, unexplained buffering was present over a pH range extending from approximately four to seven. The additional buffering was found to be associated with dissolved compounds in the fogwater. It could not be accounted for by measured concentrations of low molecular weight ( C1- C3) carboxylic acids, S(IV), phosphate, or nitrophenols. The amount of unexplained buffering in individual fog samples was found to correlate strongly with the sum of sample acetate and formate concentrations, suggesting that unmeasured organic species may be important contributors. Simulation of a Bakersfield fog episode with and without the additional, unexplained buffering revealed a significant impact on the fog chemistry. When the additional buffering was included, the simulated fog pH remained 0.3-0.7 pH units higher and the amount of sulfate present after the fog evaporated was increased by 50%. Including the additional buffering in the model simulation did not affect fogwater nitrate concentrations and was found to slightly decrease ammonium concentrations. The magnitude of the buffering effect on aqueous sulfate production is sensitive to the amount of ozone present to oxidize S

  16. Thermophysical properties of carboxylic and amino acid buffers at subzero temperatures: relevance to frozen state stabilization.

    PubMed

    Sundaramurthi, Prakash; Suryanarayanan, Raj

    2011-06-01

    Macromolecules and other thermolabile biologicals are often buffered and stored in frozen or dried (freeze-dried) state. Crystallization of buffer components in frozen aqueous solutions and the consequent pH shifts were studied in carboxylic (succinic, malic, citric, tartaric acid) and amino acid (glycine, histidine) buffers. Aqueous buffer solutions were cooled from room temperature (RT) to -25 °C and the pH of the solution was measured as a function of temperature. The thermal behavior of frozen solutions was investigated by differential scanning calorimetry (DSC), and the crystallized phases were identified by X-ray diffractometry (XRD). Based on the solubility of the neutral species of each buffer system over a range of temperatures, it was possible to estimate its degree of supersaturation at the subambient temperature of interest. This enabled us to predict its crystallization propensity in frozen systems. The experimental and the predicted rank orderings were in excellent agreement. The malate buffer system was robust with no evidence of buffer component crystallization and hence negligible pH shift. In the citrate and tartrate systems, at initial pH < pK(a)(2), only the most acidic buffer component (neutral form) crystallized on cooling, causing an increase in the freeze-concentrate pH. In glycine buffer solutions, when the initial pH was ∼3 units < isoelectric pH (pI = 5.9), β-glycine crystallization caused a small decrease in pH, while a similar effect but in the opposite direction was observed when the initial pH was ∼3 units > pI. In the histidine buffer system, depending on the initial pH, either histidine or histidine HCl crystallized.

  17. CHEMICAL SOLUTION DEPOSITION BASED OXIDE BUFFERS AND YBCO COATED CONDUCTORS

    SciTech Connect

    Paranthaman, Mariappan Parans

    2011-01-01

    We have reviewed briefly the growth of buffer and high temperature superconducting oxide thin films using a chemical solution deposition (CSD) method. In the Rolling-Assisted Biaxially Textured Substrates (RABiTS) process, developed at Oak Ridge National Laboratory, utilizes the thermo mechanical processing to obtain the flexible, biaxially oriented copper, nickel or nickel-alloy substrates. Buffers and Rare Earth Barium Copper Oxide (REBCO) superconductors have been deposited epitaxially on the textured nickel alloy substrates. The starting substrate serves as a template for the REBCO layer, which has substantially fewer weak links. Buffer layers play a major role in fabricating the second generation REBCO wire technology. The main purpose of the buffer layers is to provide a smooth, continuous and chemically inert surface for the growth of the REBCO film, while transferring the texture from the substrate to the superconductor layer. To achieve this, the buffer layers need to be epitaxial to the substrate, i.e. they have to nucleate and grow in the same bi-axial texture provided by the textured metal foil. The most commonly used RABiTS multi-layer architectures consist of a starting template of biaxially textured Ni-5 at.% W (Ni-W) substrate with a seed (first) layer of Yttrium Oxide (Y2O3), a barrier (second) layer of Yttria Stabilized Zirconia (YSZ), and a Cerium Oxide (CeO2) cap (third) layer. These three buffer layers are generally deposited using physical vapor deposition (PVD) techniques such as reactive sputtering. On top of the PVD template, REBCO film is then grown by a chemical solution deposition. This article reviews in detail about the list of oxide buffers and superconductor REBCO films grown epitaxially on single crystal and/or biaxially textured Ni-W substrates using a CSD method.

  18. Ionic equilibria in neutral amphiprotic solvents of low dielectric constant: Buffer solutions.

    PubMed

    Bosch, E; Rosés, M

    1989-06-01

    The ionic equilibria in neutral amphiprotic solvents (isopropyl and tert-butyl alcohols) have been established, and equations to calculate pH values in solutions of acids, bases, salts or their mixtures, developed. The effect, on the dissociation equilibria, of the presence of small quantities of water or other solvents in the bulk solvent used has been taken into account in the proposed equations. On the basis of these equations some buffer solutions have been studied and recommended for electrode standardization. The results, tested by experimental work, show the importance of the incompleteness of dissociation of salts in these solvents, which decreases the pH of acid buffers and increases the buffer capacity.

  19. Growth and Nutrient Uptake by Barley (Hordeum vulgare L. cv Herta): Studies Using an N-(2-Hydroxyethyl)ethylenedinitrilotriacetic Acid-Buffered Nutrient Solution Technique (I. Zinc Ion Requirements).

    PubMed Central

    Norvell, W. A.; Welch, R. M.

    1993-01-01

    The critical range of Zn2+ activity in nutrient solution required for optimum growth of barley (Hordeum vulgare L. cv Herta) was studied using the synthetic chelating agent N-(2-hydroxyethyl)ethylenedinitrilotriacetic acid to buffer micronutrient metal ions. The activity of Zn2+ was varied over a wide range from approximately 0.1 x 10-11 to 22 x 10-11 M Zn2+. The dry weight of barley shoots reached a maximum at Zn2+ activities above approximately 3 x 10-11 M and was clearly depressed when Zn2+ activities were below about 1 x 10-11 M. The relationship in shoots between dry weight and Zn concentrations supports the view that there is a critical Zn concentration of about 25 [mu]g g-1 dry weight in whole shoots of barley seedlings. When Zn2+ activities in solution were near or below approximately 3 x 10-11 M, barley shoots accumulated higher concentrations of P, Mn, Ca, Mg, and Na, whereas Cu concentrations were reduced. P and Mn began to accumulate in the shoots before differences in dry weights were apparent and provided the earliest index of Zn deficiency. In Zn-deficient roots, concentrations of Ca and Mg increased by 25 to 30%, and those of Fe and Mn more than doubled. Zn appears to play a special role in regulating uptake of several mineral nutrients in barley. PMID:12231717

  20. Ability of subsoils to buffer extremely acidic simulated coal-pile leachates

    SciTech Connect

    Zelmanowitz, S.; Boyle, W.C.; Armstrong, D.E.; Park, J.K.

    1995-11-01

    Coal piles stored directly on soil surfaces may pose a risk of ground-water contamination, particularly when extremely acidic coal-pile leachates, which contain elevated concentrations of heavy metals, are generated. Soil-column experiments were run to evaluate the ability of a sand, a silt loam, and a silt loam amended with 4% CaCO{sub 3} to buffer dilute H{sub 2}SO{sub 4} solutions (pH 3.5 and 1.5) and a synthetic coal-pile leachate (a pH 1.5 H{sub 2}SO{sub 4} solution containing metal sulfate salts). Both silt-loam soils were able to buffer the pH 3.5 H{sub 2}SO{sub 4} solution for the entire leaching period (more than 50 pore volumes), but the sand was not. The buffering capacities of all three soils were insufficient to neutralize pH 1.5 acid and synthetic coal-pile leachates. The sand exhibited the least buffering, and the silt loam at a low flow rate and the silt loam amended with CaCO{sub 3} showed the greatest buffering. The buffering capacities of both silt loam soils were exhausted more rapidly when leached with synthetic coal-pile leachate rather than pH 1.5 H{sub 2}SO{sub 4} solution. This suggests that soil-buffering studies using pure acid solutions may underpredict contamination due to coal-pile leachates. The results indicate that there is a potential for ground-water contamination due to coal-pile storage, particularly where leachates are acidic ad coarse textured soils exist. Coal storage practices should be adopted that protect soils and ground water from acidification and metals contamination.

  1. Advanced titania buffer layer architectures prepared by chemical solution deposition

    NASA Astrophysics Data System (ADS)

    Kunert, J.; Bäcker, M.; Brunkahl, O.; Wesolowski, D.; Edney, C.; Clem, P.; Thomas, N.; Liersch, A.

    2011-08-01

    Chemical solution deposition (CSD) was used to grow high-quality (100) oriented films of SrTiO3 (STO) on CSD CaTiO3 (CTO), Ba0.1Ca0.9TiO3 (BCT) and STO seed and template layers. These template films bridge the lattice misfit between STO and the nickel-tungsten (NiW) substrate, assisting in dense growth of textured STO. Additional niobium (Nb) doping of the STO buffer layer reduces oxygen diffusion which is necessary to avoid undesired oxidation of the NiW. The investigated templates offer suitable alternatives to established standard buffer systems like La2Zr2O7 (LZO) and CeO2 for coated conductors.

  2. A selective fluorescent probe for the detection of Cd(2+) in different buffer solutions and water.

    PubMed

    Xu, Zheng; Li, Guoqiang; Ren, Yuan-Yuan; Huang, Hua; Wen, Xiaoping; Xu, Qiang; Fan, Xiaotian; Huang, Zhao; Huang, Junhai; Xu, Lin

    2016-07-26

    A simple fluorescent probe NHQ based on quinoline was successfully prepared via one-step synthesis. The probe NHQ exhibited "turn-on" fluorescence and excellent selectivity toward Cd(2+) in different buffer solutions such as Tris-HCl buffer solution, HEPES buffer solution, and PBS buffer solution, and even in water. Moreover, the binding model of NHQ with Cd(2+) was definitely confirmed by the single crystal X-ray diffraction studies of the complex. PMID:27397654

  3. A selective fluorescent probe for the detection of Cd(2+) in different buffer solutions and water.

    PubMed

    Xu, Zheng; Li, Guoqiang; Ren, Yuan-Yuan; Huang, Hua; Wen, Xiaoping; Xu, Qiang; Fan, Xiaotian; Huang, Zhao; Huang, Junhai; Xu, Lin

    2016-07-26

    A simple fluorescent probe NHQ based on quinoline was successfully prepared via one-step synthesis. The probe NHQ exhibited "turn-on" fluorescence and excellent selectivity toward Cd(2+) in different buffer solutions such as Tris-HCl buffer solution, HEPES buffer solution, and PBS buffer solution, and even in water. Moreover, the binding model of NHQ with Cd(2+) was definitely confirmed by the single crystal X-ray diffraction studies of the complex.

  4. ACCURATE CHEMICAL MASTER EQUATION SOLUTION USING MULTI-FINITE BUFFERS

    PubMed Central

    Cao, Youfang; Terebus, Anna; Liang, Jie

    2016-01-01

    The discrete chemical master equation (dCME) provides a fundamental framework for studying stochasticity in mesoscopic networks. Because of the multi-scale nature of many networks where reaction rates have large disparity, directly solving dCMEs is intractable due to the exploding size of the state space. It is important to truncate the state space effectively with quantified errors, so accurate solutions can be computed. It is also important to know if all major probabilistic peaks have been computed. Here we introduce the Accurate CME (ACME) algorithm for obtaining direct solutions to dCMEs. With multi-finite buffers for reducing the state space by O(n!), exact steady-state and time-evolving network probability landscapes can be computed. We further describe a theoretical framework of aggregating microstates into a smaller number of macrostates by decomposing a network into independent aggregated birth and death processes, and give an a priori method for rapidly determining steady-state truncation errors. The maximal sizes of the finite buffers for a given error tolerance can also be pre-computed without costly trial solutions of dCMEs. We show exactly computed probability landscapes of three multi-scale networks, namely, a 6-node toggle switch, 11-node phage-lambda epigenetic circuit, and 16-node MAPK cascade network, the latter two with no known solutions. We also show how probabilities of rare events can be computed from first-passage times, another class of unsolved problems challenging for simulation-based techniques due to large separations in time scales. Overall, the ACME method enables accurate and efficient solutions of the dCME for a large class of networks. PMID:27761104

  5. A Simple and Universal Method for Making up Buffer Solutions.

    ERIC Educational Resources Information Center

    Dennison, Clive

    1988-01-01

    Uses a method which involves weighing out an amount of the appropriate weak acid or base and dissolving it in distilled water close to the final volume. Solution is then titrated with strong acid or base to give the desired pH. Provides three examples. (MVL)

  6. Predicting the crystallization propensity of carboxylic acid buffers in frozen systems--relevance to freeze-drying.

    PubMed

    Sundaramurthi, Prakash; Suryanarayanan, Raj

    2011-04-01

    Selective crystallization of buffer components in frozen solutions is known to cause pronounced pH shifts. Our objective was to study the crystallization behavior and the consequent pH shift in frozen aqueous carboxylic acid buffers. Aqueous carboxylic acid buffers were cooled to -25°C and the pH of the solution was measured as a function of temperature. The thermal behavior of solutions during freezing and thawing was investigated by differential scanning calorimetry. The crystallized phases in frozen solution were identified by X-ray diffractometry. The malate buffer system was robust with no evidence of buffer component crystallization and hence negligible pH shift. In the citrate and tartarate systems, at initial pH acidic buffer component (neutral form) crystallized on cooling, causing an increase in the freeze-concentrate pH. Carboxylic acid buffers were rank ordered based on their propensity to crystallize in frozen solutions. From the aqueous solubility values of these carboxylic acids, which have been reported over a range of temperatures, it was also possible to estimate the degree of supersaturation at the subambient temperature of interest. This enabled us to predict their crystallization propensity in frozen systems. The experimental and the predicted rank orderings were in excellent agreement.

  7. Preliminary assessment of alginic acid as a factor buffering triethanolamine interacting with artificial skin sebum.

    PubMed

    Musiał, Witold; Kubis, Aleksander

    2003-03-01

    Triethanolamine is an ethanolamine used as counter-ion for fatty acid soaps. Interaction between triethanolamine and free fatty acids is suggested to be useful for cleansing sebaceous follicles in acne prevention. This study describes the preliminary assessment of alginic acid as a factor buffering triethanolamine interacting with stearic acid--a compound of artificial skin sebum. Penetration of triethanolamine into artificial sebum, induced by the above mentioned interaction, was measured using a specific optical method. The values of the penetration depth amounted to 0.07-5.74 mm. pH values were measured. The value of pH is reduced from 10.06 for pure 1.49% (w/w) aqueous triethanolamine solution to 6.61 with the increase of the alginic acid to triethanolamine ratio in the preparations. The data of this in vitro research will support further study on other anionic polymers as factors buffering ethanolamines penetrating artificial skin sebum.

  8. Defining the buffering process by a triprotic acid without relying on Stewart-electroneutrality considerations.

    PubMed

    Nguyen, Minhtri K; Kao, Liyo; Kurtz, Ira

    2011-01-01

    Upon the addition of protons to an aqueous solution, a component of the H+ load will be bound i.e. buffered. In an aqueous solution containing a triprotic acid, H+ can be bound to three different states of the acid as well as to OH- ions that are derived from the auto-ionization of H2O. In quantifying the buffering process of a triprotic acid, one must define the partitioning of H+ among the three states of the acid and also the OH- ions in solution in order to predict the equilibrium pH value. However, previous quantitative approaches that model triprotic acid titration behaviour and used to predict the equilibrium pH rely on the mathematical convenience of electroneutrality/charge balance considerations. This fact has caused confusion in the literature, and has led to the assumption that charge balance/electroneutrality is a causal factor in modulating proton buffering (Stewart formulation). However, as we have previously shown, although charge balance can be used mathematically as a convenient tool in deriving various formulae, electroneutrality per se is not a fundamental physicochemical parameter that is mechanistically involved in the underlying buffering and proton transfer reactions. The lack of distinction between a mathematical tool, and a fundamental physicochemical parameter is in part a reason for the current debate regarding the Stewart formulation of acid-base analysis. We therefore posed the following question: Is it possible to generate an equation that defines and predicts the buffering of a triprotic acid that is based only on H+ partitioning without incorporating electroneutrality in the derivation? Towards this goal, we derived our new equation utilizing: 1) partitioning of H+ buffering; 2) conservation of mass; and 3) acid-base equilibria. In validating this model, we compared the predicted equilibrium pH with the measured pH of an aqueous solution consisting of Na2HPO4 to which HCl was added. The measured pH values were in excellent agreement

  9. Defining the buffering process by a triprotic acid without relying on Stewart-electroneutrality considerations.

    PubMed

    Nguyen, Minhtri K; Kao, Liyo; Kurtz, Ira

    2011-08-17

    Upon the addition of protons to an aqueous solution, a component of the H+ load will be bound i.e. buffered. In an aqueous solution containing a triprotic acid, H+ can be bound to three different states of the acid as well as to OH- ions that are derived from the auto-ionization of H2O. In quantifying the buffering process of a triprotic acid, one must define the partitioning of H+ among the three states of the acid and also the OH- ions in solution in order to predict the equilibrium pH value. However, previous quantitative approaches that model triprotic acid titration behaviour and used to predict the equilibrium pH rely on the mathematical convenience of electroneutrality/charge balance considerations. This fact has caused confusion in the literature, and has led to the assumption that charge balance/electroneutrality is a causal factor in modulating proton buffering (Stewart formulation). However, as we have previously shown, although charge balance can be used mathematically as a convenient tool in deriving various formulae, electroneutrality per se is not a fundamental physicochemical parameter that is mechanistically involved in the underlying buffering and proton transfer reactions. The lack of distinction between a mathematical tool, and a fundamental physicochemical parameter is in part a reason for the current debate regarding the Stewart formulation of acid-base analysis. We therefore posed the following question: Is it possible to generate an equation that defines and predicts the buffering of a triprotic acid that is based only on H+ partitioning without incorporating electroneutrality in the derivation? Towards this goal, we derived our new equation utilizing: 1) partitioning of H+ buffering; 2) conservation of mass; and 3) acid-base equilibria. In validating this model, we compared the predicted equilibrium pH with the measured pH of an aqueous solution consisting of Na2HPO4 to which HCl was added. The measured pH values were in excellent agreement

  10. Effect of N-tris (Hydroxymethyl) Methylglycine and N-2-Hydroxyethyl-piperazine-N′-2-Ethanesulfonic Acid Buffers on Linolenic Acid as a Substrate for Flaxseed Lipoxidase

    PubMed Central

    Zimmerman, Don C.

    1968-01-01

    The delay in, or loss of, flaxseed lipoxidase activity in N-tris (hydroxymethyl) methylglycine and N-2-hydroxyethylpiperazine-N′-2-ethanesulfonic acid buffers with linolenic acid as a substrate appears due to an alteration of the lipid micelle. Flaxseed lipoxidase activity is dependent on the ionic strength of the assay solution. These effects are not observed with linoleic acid as substrate. The influence of these 2 buffers on linolenic acid micelles may have a direct bearing on recent reports of chloroplast structure and activity in these buffers. PMID:16656951

  11. Buffered lidocaine and bupivacaine mixture – the ideal local anesthetic solution?

    PubMed Central

    Best, Corliss A; Best, Alyssa A; Best, Timothy J; Hamilton, Danielle A

    2015-01-01

    The use of injectable local anesthetic solutions to facilitate pain-free surgery is an integral component of many procedures performed by the plastic surgeon. In many instances, a solution that has both rapid onset and prolonged duration of analgesia is optimal. A combination of lidocaine and bupivacaine, plain or with epinephrine, is readily available in most Canadian health care settings where such procedures are performed, and fulfills these criteria. However, commercially available solutions of both medications are acidic and cause a burning sensation on injection. Buffering to neutral pH with sodium bicarbonate is a practical method to mitigate the burning sensation, and has the added benefit of increasing the fraction of nonionized lipid soluble drug available. The authors report on the proportions of the three drugs to yield a neutral pH, and the results of an initial survey regarding the use of the combined solution with epinephrine in hand surgery. PMID:26090348

  12. Ligand-enhanced electrokinetic remediation of metal-contaminated marine sediments with high acid buffering capacity.

    PubMed

    Masi, Matteo; Iannelli, Renato; Losito, Gabriella

    2016-06-01

    The suitability of electrokinetic remediation for removing heavy metals from dredged marine sediments with high acid buffering capacity was investigated. Laboratory-scale electrokinetic remediation experiments were carried out by applying two different voltage gradients to the sediment (0.5 and 0.8 V/cm) while circulating water or two different chelating agents at the electrode compartments. Tap water, 0.1 M citric acid and 0.1 M ethylenediaminetetraacetic acid (EDTA) solutions were used respectively. The investigated metals were Zn, Pb, V, Ni and Cu. In the unenhanced experiment, the acid front could not propagate due to the high acid buffering capacity of the sediments; the production of OH(-) ions at the cathode resulted in a high-pH environment causing the precipitation of CaCO3 and metal hydroxides. The use of citric acid prevented the formation of precipitates, but solubilisation and mobilisation of metal species were not sufficiently achieved. Metal removal was relevant when EDTA was used as the conditioning agent, and the electric potential was raised up to 0.8 V/cm. EDTA led to the formation of negatively charged complexes with metals which migrated towards the anode compartment by electromigration. This result shows that metal removal from sediments with high acid buffering capacity may be achieved by enhancing the electrokinetic process by EDTA addition when the acidification of the medium is not economically and/or environmentally sustainable. PMID:26490900

  13. Sulfate influx on band 3 protein of equine erythrocyte membrane (Equus caballus) using different experimental temperatures and buffer solutions.

    PubMed

    Casella, S; Piccione, D; Ielati, S; Bocchino, E G; Piccione, G

    2013-06-01

    The aim of this study was to assess the anion transport in equine erythrocytes through the measurement of the sulfate uptake operating from band 3 using different experimental temperatures and buffer solutions. Blood samples of six clinically healthy horses were collected via jugular vein puncture, and an emochrome-citometric examination was performed. The blood was divided into four aliquots and by centrifugation and aspiration the plasma and buffy coat were carefully discarded. The red blood cells were washed with an isosmotic medium and centrifuged. The obtained cell suspensions were incubated with two different experimental buffer solutions (buffer A: 115 mM Na2SO4, 10 mM NaCl, 20 mM ethylenediaminetetraacetic acid, 30 mM glucose; and buffer B: 115 mM Na2SO4, 10 mM NaCl, 20 mM ethylenediaminetetraacetic acid, 30 mM MgCl2) in a water bath for 1 h at 25 °C and 37 °C. Normal erythrocytes, suspended at 3% hematocrit, were used to measure the SO4= influx by absorption spectrophotometry at 425 nm wavelength. Unpaired Student's t-test showed a statistically significant decrease (P < 0.01) of rate constants in equine erythrocytes at 25 °C versus 37 °C using both experimental buffer solutions. Comparing the buffer A with buffer B unpaired Student's t-test showed statistically lower values (P < 0.0001) for A solution versus B solution both at 25 °C and at 37 °C. The greater inhibition of SO4 (=) influx measured in equine erythrocytes indicates the increased formation of the sulfydryl bonds in band 3 and the modulation of the sulfydryl groups, culminating in the conformational changes in band 3.

  14. Sulfate influx on band 3 protein of equine erythrocyte membrane (Equus caballus) using different experimental temperatures and buffer solutions.

    PubMed

    Casella, S; Piccione, D; Ielati, S; Bocchino, E G; Piccione, G

    2013-06-01

    The aim of this study was to assess the anion transport in equine erythrocytes through the measurement of the sulfate uptake operating from band 3 using different experimental temperatures and buffer solutions. Blood samples of six clinically healthy horses were collected via jugular vein puncture, and an emochrome-citometric examination was performed. The blood was divided into four aliquots and by centrifugation and aspiration the plasma and buffy coat were carefully discarded. The red blood cells were washed with an isosmotic medium and centrifuged. The obtained cell suspensions were incubated with two different experimental buffer solutions (buffer A: 115 mM Na2SO4, 10 mM NaCl, 20 mM ethylenediaminetetraacetic acid, 30 mM glucose; and buffer B: 115 mM Na2SO4, 10 mM NaCl, 20 mM ethylenediaminetetraacetic acid, 30 mM MgCl2) in a water bath for 1 h at 25 °C and 37 °C. Normal erythrocytes, suspended at 3% hematocrit, were used to measure the SO4= influx by absorption spectrophotometry at 425 nm wavelength. Unpaired Student's t-test showed a statistically significant decrease (P < 0.01) of rate constants in equine erythrocytes at 25 °C versus 37 °C using both experimental buffer solutions. Comparing the buffer A with buffer B unpaired Student's t-test showed statistically lower values (P < 0.0001) for A solution versus B solution both at 25 °C and at 37 °C. The greater inhibition of SO4 (=) influx measured in equine erythrocytes indicates the increased formation of the sulfydryl bonds in band 3 and the modulation of the sulfydryl groups, culminating in the conformational changes in band 3. PMID:23015199

  15. What's in your buffer? Solute altered millisecond motions detected by solution NMR.

    PubMed

    Wong, Madeline; Khirich, Gennady; Loria, J Patrick

    2013-09-17

    To date, little work has been conducted on the relationship between solute and buffer molecules and conformational exchange motion in enzymes. This study uses solution NMR to examine the effects of phosphate, sulfate, and acetate in comparison to MES- and HEPES-buffered references on the chemical shift perturbation and millisecond, chemical, or conformational exchange motions in the enzyme ribonuclease A (RNase A), triosephosphate isomerase (TIM) and HisF. The results indicate that addition of these solutes has a small effect on (1)H and (15)N chemical shifts for RNase A and TIM but a significant effect for HisF. For RNase A and TIM, Carr-Purcell-Meiboom-Gill relaxation dispersion experiments, however, show significant solute-dependent changes in conformational exchange motions. Some residues show loss of millisecond motions relative to the reference sample upon addition of solute, whereas others experience an enhancement. Comparison of exchange parameters obtained from fits of dispersion data indicates changes in either or both equilibrium populations and chemical shifts between conformations. Furthermore, the exchange kinetics are altered in many cases. The results demonstrate that common solute molecules can alter observed enzyme millisecond motions and play a more active role than what is routinely believed.

  16. The application of animal models to study the biocompatibility of bicarbonate-buffered peritoneal dialysis solutions.

    PubMed

    ter Wee, P M; Beelen, R H J; van den Born, J

    2003-12-01

    The application of animal models to study the biocompatibility of bicarbonate-buffered peritoneal dialysis solutions. Patients treated with peritoneal dialysis (PD) are at risk for development of ultrafiltration failure and peritonitis. These two significant complications can result in the termination of PD treatment. The relative unphysiologic composition of the currently used standard peritoneal dialysis fluids (PDF) is considered to be a major cause for the development of morphologic changes of the peritoneal membrane, ultimately resulting in ultrafiltration failure and probably contributing to changes in local defense mechanisms with the associated increased risk of peritonitis. In recent years, a major research focus has become the development of new and improved PD solutions. This has resulted in the development of an amino-acid-based PDF, a glucose polymer-based PDF, and several bicarbonate-buffered PDF. Typically, the first phase of biocompatibility testing of new PD solutions involves in vitro testing, employing isolated cells such as peritoneal macrophages or cell culture systems using human peritoneal mesothelial cells. The results of such evaluations are useful in providing insights into the biocompatibility performance of any given formulation, but suffer from several disadvantages, which can be better addressed using animal models. In vivo studies using animals permit the analysis of biocompatibility under conditions that allow for cell-to-cell interactions and dynamic changes in solution composition that more closely mimic the clinical situation. In this paper, we will review the use of animal models for the study of PDF biocompatibility and their application to the assessment of bicarbonate-buffered PDF.

  17. Analysis of Natural Buffer Systems and the Impact of Acid Rain

    ERIC Educational Resources Information Center

    Powers, David C.; Yoder, Claude H.; Higgs, Andrew T.; Obley, Matt L.; Hess, Kenneth R.; Leber, Phyllis A.

    2005-01-01

    The environmental significance of acid rain on water systems of different buffer capacities is discussed. The most prevalent natural buffer system is created by the equilibrium between carbonate ions and carbon dioxide.

  18. Calorimetric and Diffractometric Evidence for the Sequential Crystallization of Buffer Components and the Consequential pH Swing in Frozen Solutions

    SciTech Connect

    Sundaramurthi, Prakash; Shalaev, Evgenyi; Suryanarayanan, Raj

    2010-06-22

    Sequential crystallization of succinate buffer components in the frozen solution has been studied by differential scanning calorimetry and X-ray diffractometry (both laboratory and synchrotron sources). The consequential pH shifts were monitored using a low-temperature electrode. When a solution buffered to pH < pK{sub a2} was cooled from room temperature (RT), the freeze-concentrate pH first increased and then decreased. This was attributed to the sequential crystallization of succinic acid, monosodium succinate, and finally disodium succinate. When buffered to pH > pK{sub a2}, the freeze-concentrate pH first decreased and then increased due to the sequential crystallization of the basic (disodium succinate) followed by the acidic (monosodium succinate and succinic acid) buffer components. XRD provided direct evidence of the crystallization events in the frozen buffer solutions, including the formation of disodium succinate hexahydrate [Na{sub 2}(CH{sub 2}COO){sub 2} {center_dot} 6H{sub 2}O]. When the frozen solution was warmed in a differential scanning calorimeter, multiple endotherms attributable to the melting of buffer components and ice were observed. When the frozen solutions were dried under reduced pressure, ice sublimation was followed by dehydration of the crystalline hexahydrate to a poorly crystalline anhydrate. However, crystalline succinic acid and monosodium succinate were retained in the final lyophiles. The pH and the buffer salt concentration of the prelyo solution influenced the crystalline salt content in the final lyophile. The direction and magnitude of the pH shift in the frozen solution depended on both the initial pH and the buffer concentration. In light of the pH-sensitive nature of a significant fraction of pharmaceuticals (especially proteins), extreme care is needed in both the buffer selection and its concentration.

  19. Enhancement of the absorption of CO{sub 2} in alkaline buffer solutions: Joint action of two enhancers

    SciTech Connect

    Vazquez, G.; Chenlo, F.; Pereira, G.; Vazquez, P.

    1999-05-01

    The authors measured the absorption of CO{sub 2} in alkaline 0.5 M/0.5 M sodium carbonate/bicarbonate buffers containing either saccharose and sodium arsenite or saccharose and formaldehyde. Absorption enhancement increased upon increasing the concentration of either of the catalysts, but the joint action of the two was always less than the sum of their individual effects, the difference being a function of the acidities and concentrations of the catalysts and the pH of the carbonate/bicarbonate buffer solution

  20. Improving lanthanide nanocrystal colloidal stability in competitive aqueous buffer solutions using multivalent PEG-phosphonate ligands.

    PubMed

    Cao, Pengpeng; Tong, Lemuel; Hou, Yi; Zhao, Guangyao; Guerin, Gerald; Winnik, Mitchell A; Nitz, Mark

    2012-09-01

    The range of properties available in the lanthanide series has inspired research into the use of lanthanide nanoparticles for numerous applications. We aim to use NaLnF(4) nanoparticles for isotopic tags in mass cytometry. This application requires nanoparticles of narrow size distribution, diameters preferably less than 15 nm, and robust surface chemistry to avoid nonspecific interactions and to facilitate bioconjugation. Nanoparticles (NaHoF(4), NaEuF(4), NaGdF(4), and NaTbF(4)) were synthesized with diameters from 9 to 11 nm with oleic acid surface stabilization. The surface ligands were replaced by a series of mono-, di-, and tetraphosphonate PEG ligands, whose synthesis is reported here. The colloidal stability of the resulting particles was monitored over a range of pH values and in phosphate containing solutions. All of the PEG-phosphonate ligands were found to produce non-aggregated colloidally stable suspensions of the nanoparticles in water as judged by DLS and TEM measurements. However, in more aggressive solutions, at high pH and in phosphate buffers, the mono- and diphosphonate PEG ligands did not stabilize the particles and aggregation as well as flocculation was observed. However, the tetraphosphonate ligand was able to stabilize the particles at high pH and in phosphate buffers for extended periods of time.

  1. Redox buffered hydrofluoric acid etchant for the reduction of galvanic attack during release etching of MEMS devices having noble material films

    DOEpatents

    Hankins, Matthew G.

    2009-10-06

    Etchant solutions comprising a redox buffer can be used during the release etch step to reduce damage to the structural layers of a MEMS device that has noble material films. A preferred redox buffer comprises a soluble thiophosphoric acid, ester, or salt that maintains the electrochemical potential of the etchant solution at a level that prevents oxidation of the structural material. Therefore, the redox buffer preferentially oxidizes in place of the structural material. The sacrificial redox buffer thereby protects the exposed structural layers while permitting the dissolution of sacrificial oxide layers during the release etch.

  2. [Influence of buffer solutions on the performance of microbial fuel cell electricity generation].

    PubMed

    Qiang, Lin; Yuan, Lin-jiang; Ding, Qing

    2011-05-01

    Microbial fuel cell (MFC) is a potential green technology due to its application in wastewater treatment and renewable energy generation. Phosphate buffer solution (PBS) has been commonly used in MFC studies to maintain a suitable pH for electricity generating bacteria and/or to increase the solution conductivity. However, it has some drawbacks using PBS in MFC: One is that the addition of a high concentration of phosphate buffer in MFCs is expensive, especially for the application in wastewater treatment; the other is that phosphates can contribute to the eutrophication conditions of water bodies if the effluents are discharged without the removal of phosphates. By adding PBS buffer as the comparison, the study investigated the effect of borax buffer and in the absence of buffer on the performance of electrical power, coulomb efficiency and effluent pH. 200 mmol/L PBS was the best, conductivity was 1.973 mS/cm,the maximum power density was 36.4 mW/m2 and the maximum coulomb efficiency was 2.92%, effluent pH was almost at (7.00 +/- 0.05). 100 mmol/L borax buffer solution, conductivity was 1.553 mS/cm; the maximum power density was 26.2 mW/m2 coulomb efficiency of 6.26%, which was 2.14 times to PBS and greatly increased the electron recovery efficiency with the effluent pH was (7.35 +/- 0.05). While free buffer solution conductivity was 0.314 mS/cm, maximum power density was 27.64 mW/m2; coulomb efficiency was 2.82% and the effluent pH of approximately 7.43. The electrolyte which in absence of buffer solution conductivity was 1/6 of adding PBS buffer, 1/5 of borax buffer, while its power density lower 8.76 mW/mr2 than adding PBS and higher 1.24 mW/m2 than borax buffer. The results showed that adding the suitable concentration of borax buffer may improve the electron recovery efficiency and under batch conditions, MFC run successfully without adding buffer solution to MFC.

  3. A biogeochemical comparison of two well-buffered catchments with contrasting histories of acid deposition

    USGS Publications Warehouse

    Shanley, J.B.; Kram, P.; Hruska, J.; Bullen, T.D.

    2004-01-01

    Much of the biogeochemical cycling research in catchments in the past 25 years has been driven by acid deposition research funding. This research has focused on vulnerable base-poor systems; catchments on alkaline lithologies have received little attention. In regions of high acid loadings, however, even well-buffered catchments are susceptible to forest decline and episodes of low alkalinity in streamwater. As part of a collaboration between the Czech and U.S. Geological Surveys, we compared biogeochemical patterns in two well-studied, well-buffered catchments: Pluhuv Bor in the western Czech Republic, which has received high loading of atmospheric acidity, and Sleepers River Research Watershed in Vermont, U.S.A., where acid loading has been considerably less. Despite differences in lithology, wetness, forest type, and glacial history, the catchments displayed similar patterns of solute concentrations and flow. At both catchments, base cation and alkalinity diluted with increasing flow, whereas nitrate and dissolved organic carbon increased with increasing flow. Sulfate diluted with increasing flow at Sleepers River, while at Pluhuv Bor the sulfate-flow relation shifted from positive to negative as atmospheric sulfur (S) loadings decreased and soil S pools were depleted during the 1990s. At high flow, alkalinity decreased to near 100 ??eq L-1 at Pluhuv Bor compared to 400 ??eq L-1 at Sleepers River. Despite the large amounts of S flushed from Pluhuv Bor soils, these alkalinity declines were caused solely by dilution, which was greater at Pluhuv Bor relative to Sleepers River due to greater contributions from shallow flow paths at high flow. Although the historical high S loading at Pluhuv Bor has caused soil acidification and possible forest damage, it has had little effect on the acid/base status of streamwater in this well-buffered catchment. ?? 2004 Kluwer Academic Publishers.

  4. Tested Demonstrations: Buffer Capacity of Various Acetic Acid-Sodium Acetate Systems: A Lecture Experiment.

    ERIC Educational Resources Information Center

    Donahue, Craig J.; Panek, Mary G.

    1985-01-01

    Background information and procedures are provided for a lecture experiment which uses indicators to illustrate the concept of differing buffer capacities by titrating acetic acid/sodium acetate buffers with 1.0 molar hydrochloric acid and 1.0 molar sodium hydroxide. A table with data used to plot the titration curve is included. (JN)

  5. Comparison and trend study on acidity and acidic buffering capacity of particulate matter in China

    NASA Astrophysics Data System (ADS)

    Ren, Lihong; Wang, Wei; Wang, Qingyue; Yang, XiaoYang; Tang, Dagang

    2011-12-01

    The acidity of about 2000 particulate matter samples from aircraft and ground-based monitoring is analyzed by the method similar to soil acidity determination. The ground-based samples were collected at about 50 urban or background sites in northern and southern China. Moreover, the acidic buffering capacity of those samples is also analyzed by the method of micro acid-base titration. Results indicate that the acidity level is lower in most northern areas than those in the south, and the acidic buffering capacity showed inverse tendency, correspondingly. This is the most important reason why the pollution of acidic-precipitation is much more serious in Southern China than that in Northern China. The acidity increases and the acidic buffering capacity drops with the decreasing of the particle sizes, indicating that fine particle is the main influencing factor of the acidification. The ionic results show that Ca salt is the main alkaline substance in particulate matter, whereas the acidification of particulate matter is due to the SO 2 and NO x emitted from the fossil fuel burning. And among of them, coal burning is the main contributor of SO 2, however the contribution of NO x that emitted from fuel burning of motor vehicles has increased in recent years. By comparison of the experimental results during the past 20 years, it can be concluded that the acid precipitation of particulate matter has not been well controlled, and it even shows an increasing tendency in China lately. The acid precipitation of particulate matter has begun to frequently attack in part of the northern areas. Multiple regression analysis indicates that coefficient value of the ions is the lowest at the urban sites and the highest at the regional sites, whereas the aircraft measurement results are intermediate between those two kinds of sites.

  6. Critical evaluation of buffering solutions for pKa determination by capillary electrophoresis.

    PubMed

    Fuguet, Elisabet; Reta, Mario; Gibert, Carme; Rosés, Martí; Bosch, Elisabeth; Ràfols, Clara

    2008-07-01

    The performance of the most common and also some other less common CE buffers has been tested for the pKa determination of several types of compounds (pyridine, amines, and phenols). The selected buffers cover a pH ranging from 3.7 to 11.8. Whereas some buffers, like acetic acid/acetate, BisTrisH+/BisTris, TrisH+/Tris, CHES/CHES-, and CAPS/CAPS- can be used with all type of analytes, others like ammonium/ammonia, butylammonium/butylammonia, ethylammonium/ethylammonia, diethylammonium/diethylammonia, and hydrogenphosphate/phosphate are not recommended because they interact with a wide range of compounds. The rest of the tested buffers (dihydrogenphosphate/hydrogenphosphate, MES/MES-, HEPES/HEPES-, and boric acid/borate) can show specific interactions depending on the nature of the analytes, and their use in some applications should be restricted.

  7. The Determination of the pH of Standard Buffer Solution: A Laboratory Experiment.

    ERIC Educational Resources Information Center

    Harris, K. R.

    1985-01-01

    Describes an experiment which shows: (1) how measurements of the reaction electromotive force for the cell (Pt/glass/NaCl(aq,m),buffer/AgCl/Ag/Pt) can be utilized in determining the absolute pH of the buffer; and (2) the demonstration of the use of the Debye-Huckel model of an electrolyte solution in solving an important electrochemical problem.…

  8. [Alanine solution as enzyme reaction buffer used in A to O blood group conversion].

    PubMed

    Li, Su-Bo; Zhang, Xue; Zhang, Yin-Ze; Tan, Ying-Xia; Bao, Guo-Qiang; Wang, Ying-Li; Ji, Shou-Ping; Gong, Feng; Gao, Hong-Wei

    2014-06-01

    The aim of this study was to investigate the effect of alanine solution as α-N-acetylgalactosaminidase enzyme reaction buffer on the enzymatic activity of A antigen. The binding ability of α-N-acetylgalactosaminidase with RBC in different reaction buffer such as alanine solution, glycine solution, normal saline (0.9% NaCl), PBS, PCS was detected by Western blot. The results showed that the efficiency of A to O conversion in alanine solution was similar to that in glycine solution, and Western blot confirmed that most of enzymes blinded with RBC in glycine or alanine solution, but few enzymes blinded with RBC in PBS, PCS or normal saline. The evidences indicated that binding of enzyme with RBC was a key element for A to O blood group conversion, while the binding ability of α-N-acetylgalactosaminidase with RBC in alanine or glycine solution was similar. It is concluded that alanine solution can be used as enzyme reaction buffer in A to O blood group conversion. In this buffer, the α-N-acetylgalactosaminidase is closely blinded with RBC and α-N-acetylgalactosaminidase plays efficient enzymatic activity of A antigen.

  9. The Effect of Crystallizing and Non-crystallizing Cosolutes on Succinate Buffer Crystallization and the Consequent pH Shift in Frozen Solutions

    SciTech Connect

    Sundaramurthi, Prakash; Suryanarayanan, Raj

    2011-09-06

    To effectively inhibit succinate buffer crystallization and the consequent pH changes in frozen solutions. Using differential scanning calorimetry (DSC) and X-ray diffractometry (XRD), the crystallization behavior of succinate buffer in the presence of either (i) a crystallizing (glycine, mannitol, trehalose) or (ii) a non-crystallizing cosolute (sucrose) was evaluated. Aqueous succinate buffer solutions, 50 or 200 mM, at pH values 4.0 or 6.0 were cooled from room temperature to -25 C at 0.5 C/min. The pH of the solution was measured as a function of temperature using a probe designed to function at low temperatures. The final lyophiles prepared from these solutions were characterized using synchrotron radiation. When the succinic acid solution buffered to pH 4.0, in the absence of a cosolute, was cooled, there was a pronounced shift in the freeze-concentrate pH. Glycine and mannitol, which have a tendency to crystallize in frozen solutions, remained amorphous when the initial pH was 6.0. Under this condition, they also inhibited buffer crystallization and prevented pH change. At pH 4.0 (50 mM initial concentration), glycine and mannitol crystallized and did not prevent pH change in frozen solutions. While sucrose, a non-crystallizing cosolute, did not completely prevent buffer crystallization, the extent of crystallization was reduced. Sucrose decomposition, based on XRD peaks attributable to {beta}-D-glucose, was observed in frozen buffer solutions with an initial pH of 4.0. Trehalose completely inhibited crystallization of the buffer components when the initial pH was 6.0 but not at pH 4.0. At the lower pH, the crystallization of both trehalose dihydrate and buffer components was evident. When retained amorphous, sucrose and trehalose effectively inhibited succinate buffer component crystallization and the consequent pH shift. However, when trehalose crystallized or sucrose degraded to yield a crystalline decomposition product, crystallization of buffer was

  10. Calcium buffer solutions and how to make them: a do it yourself guide.

    PubMed

    McGuigan, J A; Lüthi, D; Buri, A

    1991-11-01

    In measurements of the intracellular free calcium concentration ([Ca2+]) using either microelectrodes or fluorescent probes, calibration is normally carried out in EGTA calcium buffer solutions. In the first part of the article the general properties of calcium buffer solutions are discussed, the equations used to calculate the apparent calcium binding constant (Kapp) are derived, and the difficulties in the calculation are discussed. The effects of the purity of EGTA as well as the influence of calcium contamination on the buffer solutions are explained. Because of the difficulties in calculating Kapp, and the importance of EGTA purity and calcium contamination, it is suggested that it is easier to measure all three under the appropriate experimental conditions using the method of Bers (1982). In the second part a do-it-yourself guide to the preparation of EGTA calcium buffer solutions is given. An experimental example is provided using the Bers method to measure purity, contamination, and Kapp. It is concluded that unless all three factors are known it is not possible to prepare accurate EGTA calcium buffer solutions.

  11. Influence of solid-state acidity on the decomposition of sucrose in amorphous systems II (effect of buffer).

    PubMed

    Alkhamis, Khouloud A

    2009-04-01

    It was of interest to investigate the solid-state acidity using indicator probe molecules and sucrose degradation. Amorphous samples containing lactose, sucrose, buffers (citrate, malate, tartarate, or phosphate) with different pH values, and sodium chloride (to adjust the ionic strength) were prepared by freeze-drying. The lyophiles were characterized using powder X-ray diffraction, differential scanning calorimetry, and Karl Fischer titrimetry. The solid-state acidity of all lyophiles was measured using diffuse reflectance spectroscopy and suitable indicators (thymol blue or bromophenol blue). Selected lyophiles were subjected to a temperature of 60 degrees C and were analyzed for sucrose degradation using the Trinder kit. The results obtained from this study have shown that good correlation can be obtained between the solid-state acidity and the molar ratio of the salt and the acid in solution. The degradation of sucrose in the lyophiles is extremely sensitive to the solid-state acidity and might be able to provide a better estimate for the acidity than the indicator probe molecules. The Hammett acidity-rate profile for sucrose degradation in the lyophiles (using four different buffers) was also obtained. The profile showed similarity to the pH-rate profile in solution, and no buffer catalysis for sucrose degradation was detected in this study. PMID:19016102

  12. Influence of buffered and unbuffered acetylsalicylic acid on dental enamel and dentine in human teeth: an in vitro pilot study.

    PubMed

    Rogalla, K; Finger, W; Hannig, M

    1992-06-01

    An in vitro study was conducted to investigate the erosive effect of buffered and unbuffered acetylsalicylic acid (ASA) on dental enamel and dentine in human teeth by scanning electron microscopy. In order to standardize the specimens and to improve comparability the dental enamel and dentine were superficially abraded. The enamel and dentine specimens were therefore particularly sensitive to the influences of acid agents. Concentrated solution of buffered chewable ASA tablets (500 mg ASA and 300 mg calcium carbonate in 5 ml water) showed no changes in the enamel surface structure after exposure times of 1 min, 5 min and 60 min. In contrast, minimal corrosive effects were already seen after exposure of the enamel surface to the unbuffered ASA solutions for 1 min. After exposure times of 5 min and 60 min erosion of the enamel was more pronounced. Immersion in the unbuffered ASA solution led to clearly visible micromorphological changes on the dentine surfaces even after exposure for 1 min. Exposure of the dentine specimens to the buffered ASA solutions led to only very slight changes in the surface morphology. Therefore, the scanning electron micrograph after exposure to buffered ASA is comparable to the picture of untreated dentine. PMID:1513188

  13. Comparison of Ring-Buffer-Based Packet Capture Solutions

    SciTech Connect

    Barker, Steven Andrew

    2015-10-01

    Traditional packet-capture solutions using commodity hardware incur a large amount of overhead as packets are copied multiple times by the operating system. This overhead slows sensor systems to a point where they are unable to keep up with high bandwidth traffic, resulting in dropped packets. Incomplete packet capture files hinder network monitoring and incident response efforts. While costly commercial hardware exists to capture high bandwidth traffic, several software-based approaches exist to improve packet capture performance using commodity hardware.

  14. Inhibition of protein carbamylation in urea solution using ammonium-containing buffers.

    PubMed

    Sun, Shisheng; Zhou, Jian-Ying; Yang, Weiming; Zhang, Hui

    2014-02-01

    Urea solution is one of the most commonly employed protein denaturants for protease digestion in proteomic studies. However, it has long been recognized that urea solution can cause carbamylation at the N termini of proteins/peptides and at the side chain amino groups of lysine and arginine residues. Protein/peptide carbamylation blocks protease digestion and affects protein identification and quantification in mass spectrometry analysis by blocking peptide amino groups from isotopic/isobaric labeling and changing peptide charge states, retention times, and masses. In addition, protein carbamylation during sample preparation makes it difficult to study in vivo protein carbamylation. In this study, we compared the peptide carbamylation in urea solutions of different buffers and found that ammonium-containing buffers were the most effective buffers to inhibit protein carbamylation in urea solution. The possible mechanism of carbamylation inhibition by ammonium-containing buffers is discussed, and a revised procedure for the protease digestion of proteins in urea and ammonium-containing buffers was developed to facilitate its application in proteomic research.

  15. Diffusion of ionizable solutes across planar lipid bilayer membranes: boundary-layer pH gradients and the effect of buffers.

    PubMed

    Xiang, T X; Anderson, B D

    1993-11-01

    The diffusion of weak acids or bases across planar lipid bilayer membranes results in aqueous boundary layer pH gradients. If not properly taken into account, such pH gradients will lead to errors in estimated membrane permeability coefficients, Pm. The role of the permeant concentration, the buffer capacity, and the physicochemical properties of both permeant and buffer on the magnitude and impact of such pH gradients have been explored. A theoretical model has been developed to describe the diffusion of both permeant and buffer species. Significant pH gradients develop depending on solution pH and the pKa's, concentrations, and Pm values of both permeant and buffer. The relative error in experimentally determined Pm values was calculated as the ratio, r, between apparent Pm values (obtained from flux measurements using an equation which neglected boundary layer pH gradients) and its true value. Simulated r values ranged from 1 (0% error) to < 0.01 (> 100% error) for weak acids, decreasing with decreasing buffer capacity and increasing solute flux. The buffer capacity required for an r > 0.95 was calculated versus pH for permeants varying in pKa and Pm. Membrane-permeable buffers significantly reduce boundary layer pH gradients through a feedback effect due to buffer cotransport. Apparent Pm values of p-hydroxymethyl benzoic acid across lecithin bilayer membranes at 25 degrees C were obtained as a function of permeant concentration in various buffers [glycolic, 2-(N-morpholino)ethane-sulfonic, and formic acids]. Predictions agreed closely with experimental fluxes. PMID:8290481

  16. Influence of phosphate ions on buffer capacity of soil humic acids

    NASA Astrophysics Data System (ADS)

    Boguta, P.; Sokołowska, Z.

    2012-02-01

    The object of this study was to determine change of natural buffer capacity of humic acids by strong buffering agents, which were phosphate ions. Studies were carried out on the humic acids extracted from peat soils. Additional information was obtained by determination of water holding capacity, density, ash and pH for peats and optical parameter Q4/6 for humic acids. Humic acid suspensions exhibited the highest buffer properties at low pH and reached maximum at pH ~ 4. Phosphates possessed buffer properties in the pH range from 4.5 to 8.0. The maximum of buffering was at pH~6.8 and increased proportionally with an increase in the concentration of phosphate ions. The study indicated that the presence of phosphate ions may strongly change natural buffer capacity of humic acids by shifting buffering maximum toward higher pH values. Significant correlations were found for the degree of the secondary transformation with both the buffer capacity and the titrant volume used during titration.

  17. Multi-ion sensing of buffer solutions using terahertz chemical microscopy

    NASA Astrophysics Data System (ADS)

    Akimune, Kosuke; Okawa, Yuki; Sakai, Kenji; Kiwa, Toshihiko; Tsukada, Keiji

    2014-12-01

    Terahertz chemical microscopy (TCM) has been proposed and developed to visualize electric potential and/or chemical changes in water solutions. To simultaneously detect two types of ions mixed in buffer solutions, five membranes for sodium ions and four membranes for potassium ions were integrated on a sensing plate, and the selectivity to each ion was evaluated. The results suggest that TCM can be used for multi-ion sensing in mixed solutions.

  18. Oxygen permeability of soft contact lenses in different pH, osmolality and buffering solution

    PubMed Central

    Lee, Se Eun; Kim, So Ra; Park, Mijung

    2015-01-01

    AIM To determine the effect of pH, osmolality, and buffering system on the oxygen permeability (Dk) of soft contact lenses. METHODS Two hydrogel lenses (nelfilcon A and etafilcon A) and 2 silicone hydrogel lenses (lotrafilcon A and balafilcon A) were used in the study. These lenses were incubated in phosphate-buffered saline (PBS) and borate-buffered saline (BBS) solutions adjusted by 0.8 pH increments to a pH in the range of 5.8-9.0 or in hypotonic (280 mOsmol/kg), isotonic (310 mOsmol/kg) and hypertonic (380 mOsmol/kg) PBS solutions. Polarographic method was used for measuring the Dk and lenses were stacked as 4 layers to correct the boundary effect. RESULTS Dk values of all contact lenses measured in BBS solutions were more stable than those in PBS solutions. Especially the etafilcon A lens showed a relative big change compared with other types of contact lenses at the same conditions. When the osmolality of PBS solution increased from hypotonic to hypertonic, Dk of all contact lenses decreased. Variations in Dk existed depending on lens materials, etafilcon A lens was the most affected and nelfilcon A was the least affected by osmolality. CONCLUSION From the result obtained, it is revealed that Dk of contact lenses is changed by the pH, osmolality, and buffering condition of tear. Thus, Dk of contact lens can be varied by the lens wearers' physiological and/or pathological conditions. PMID:26558223

  19. On the use of dimensionless parameters in acid-base theory. V. Buffers composed of binary mixtures of monovalent weak acids and bases.

    PubMed

    Rilbe, H

    1993-12-01

    A general theory for buffers consisting of one weak acid and one weak base is developed, particular interest being devoted to the special case of doubly weak salts. The pH course as it varies with the acid/base concentration ratio is presented in equations and graphs. The influence of delta pK' = pK'b-pK'a, which can be negative as well as positive, is discussed and visualized in graphs. The buffer capacity is deduced as a function of pH. The buffer range is, at a maximum, 2.67 times that of a monovalent weak protolyte for delta pK' = 2.7 pH units. The buffer capacity curve has two maxima for delta pK' values bigger than 0.77. For negative delta pK' values the buffer capacity curve has only one maximum, and the buffer range is not better than that of a monovalent protolyte. A general equation for the ionic concentrations is deduced, and as a corollary the degree of hydrolysis of the doubly weak salt is obtained as a function of delta pK'. For solutions of this salt, the relation between concentration and pH is elucidated by equations and graphs. PMID:8137789

  20. Acanthamoeba encystment: multifactorial effects of buffers, biocides, and demulcents present in contact lens care solutions

    PubMed Central

    Kovacs, Christopher J; Lynch, Shawn C; Rah, Marjorie J; Millard, Kimberly A; Morris, Timothy W

    2015-01-01

    Purpose To determine whether agents which are purportedly capable of inducing encystment of Acanthamoeba can recapitulate the signal when tested in differing formulations. Methods In accordance with the International Standard ISO 19045, Acanthamoeba castellanii ATCC 50370 trophozoites were cultured in antibiotic-free axenic medium, treated with test solutions, and encystment rates plus viability were measured via bright field and fluorescent microscopy. Test solutions included phosphate-buffered saline (PBS), borate-buffered saline, biguanide- and hydrogen peroxide (H2O2)-based biocides, propylene glycol (PG) and povidone (POV) ophthalmic demulcents, and one-step H2O2-based contact lens disinfection systems. Results Only PBS solutions with 0.25 ppm polyaminopropyl biguanide (PAPB) and increasing concentrations of PG and POV stimulated A. castellanii encystment in a dose-dependent manner, whereas PBS solutions containing 3% H2O2 and increasing concentrations of PG and POV did not stimulate encystment. Borate-buffered saline and PBS/citrate solutions containing PG also did not stimulate encystment. In addition, no encystment was observed after 24 hours, 7 days, or 14 days of exposures of trophozoites to one-step H2O2 contact lens disinfection products or related solutions. Conclusion The lack of any encystment observed when trophozoites were treated with existing or new one-step H2O2 contact lens care products, as well as when trophozoites were exposed to various related test solutions, confirms that Acanthamoeba encystment is a complex process which depends upon simultaneous contributions of multiple factors including buffers, biocides, and demulcents. PMID:26508829

  1. Evidence that intrinsic iron but not intrinsic copper determines S-nitrosocysteine decomposition in buffer solution.

    PubMed

    Vanin, Anatoly F; Muller, Bernard; Alencar, Jacicarlos L; Lobysheva, Irina I; Nepveu, Françoise; Stoclet, Jean-Claude

    2002-11-01

    The present experiments were designed to analyze the influence of copper and iron ions on the process of decomposition of S-nitrosocysteine (cysNO), the most labile species among S-nitrosothiols (RSNO). CysNO fate in buffer solution was evaluated by optical and electron paramagnetic resonance (EPR) spectroscopy, and the consequences on its vasorelaxant effect were studied on noradrenaline-precontracted rat aortic rings. The main results are the following: (i) copper or iron ions, especially in the presence of the reducing agent ascorbate, accelerated the decomposition of cysNO and markedly attenuated the amplitude and duration of the relaxant effect of cysNO; (ii) by contrast, the iron and copper chelators bathophenantroline disulfonic acid (BPDS) and bathocuproine disulfonic acid (BCS) exerted a stabilizing effect on cysNO, prolonged its vasorelaxant effect, and abolished the influence of ascorbate; (iii) in the presence of ascorbate, BPDS displayed a selective inhibitory effect toward the influence of iron ions (but not toward copper ions) on cysNO decomposition and vasorelaxant effect, while BCS prevented the effects of both copper and iron ions; (iv) L-cysteine enhanced stability and prolonged the relaxant effect of cysNO; (v) the process of iron-induced decomposition of cysNO was associated with the formation of EPR-detectable dinitrosyl-iron complexes (DNIC) either with non-thiol- or thiol-containing ligands (depending on the presence of L-cysteine), both of which exhibiting vasorelaxant properties. From these data, it is concluded that the amount of intrinsic copper was probably too low to produce a destabilizing effect even on the most labile RSNO, cysNO, and that only intrinsic iron, through the formation of DNIC, was responsible for the process of cysNO decomposition and thus influenced its vasorelaxant properties. PMID:12381416

  2. Hydrogen production in microbial reverse-electrodialysis electrolysis cells using a substrate without buffer solution.

    PubMed

    Song, Young-Hyun; Hidayat, Syarif; Kim, Han-Ki; Park, Joo-Yang

    2016-06-01

    The aim of this work was to use substrate without buffer solution in a microbial reverse-electrodialysis electrolysis cell (MREC) for hydrogen production under continuous flow condition (10 cell pairs of RED stacks, HRT=5, 7.5, and 15h). Decreasing in the HRT (increasing in the organic matter) made cell current stable and increased. Hydrogen gas was produced at a rate of 0.61m(3)-H2/m(3)-Van/d in H-MREC, with a COD removal efficiency of 81% (1.55g/L/d) and a Coulombic efficiency of 41%. This MREC system without buffer solution could successfully produce hydrogen gas at a consistent rate. PMID:26888336

  3. Structural transitions in polycytidylic acid: proton buffer capacity data.

    PubMed

    Zarudnaya, Margarita I; Samijlenko, Svitlana P; Potyahaylo, Andriy L; Hovorun, Dmytro M

    2002-01-01

    The pH-dependences of proton buffer capacity of poly(C) were computed on the basis of the literature data. In these curves there were observed four peaks: two narrow and two wide ones. The first narrow peak reflects the process of cooperative formation of double helices, which is induced by protonation of the N3 atom of nucleotide bases. The first wide peak is assigned to noncooperative process of poly(C) double helices protonation at the N3 nitrogen atom. It is proposed that the second wide peak corresponds to noncooperative protonation of the neutral cytosine bases at the oxygen atom. This reaction causes cooperative dissociation of the poly(C) double helices. The second narrow peak reflects the dissociation process. PMID:11991140

  4. Mitigation of chromatography adsorbent lot performance variability through control of buffer solution design space.

    PubMed

    Aono, Hiromasa; Iliescu, Ionela; Cecchini, Doug; Wood, Susanne; McCue, Justin T

    2013-11-29

    The separation of undesired product-related impurities often poses a challenge in the purification of protein therapeutic species. Product-related impurity species, which may consist of undesirable isoforms, aggregated, or misfolded variants of the desired monomeric form of the product, can be challenging to remove using preparatory scale chromatographic techniques. When using anion exchange chromatography to remove undesirable product-related impurities, the separation can be highly sensitive to relatively small changes in the chromatography operating conditions, including changes to buffer solution pH, buffer solution conductivity protein loading, and operating temperature. When performing difficult separations, slight changes to the chemical and physical properties of the anion exchange adsorbent lot may also impact the separation profile. Such lot-to-lot variability may not be readily measurable by the adsorbent manufacturer, since variability can be highly dependent on a specific protein separation. Consequently, manufacturers of chromatographic adsorbents may not be able to control adsorbent lot to lot variability tightly enough to prevent differences from occurring when performing difficult product-related separations at the preparatory scale. In such cases, it is desirable to design a chromatography step with a control strategy which accounts for adsorbent lot to lot variability in the separation performance. In order to avoid the undesired changes to process consistency and product quality, a proper adjustment of the column operating conditions can be implemented, based on the performance of each adsorbent lot or lot mixture. In this work, we describe how the adjustment of the column buffer solution composition can be used as a design space based-control strategy used to ensure consistent process performance and product quality are achieved for an anion exchange chromatography step susceptible to adsorbent lot to lot performance variability. In addition, a

  5. Exciton-blocking phosphonic acid-treated anode buffer layers for organic photovoltaics

    NASA Astrophysics Data System (ADS)

    Zimmerman, Jeramy D.; Song, Byeongseop; Griffith, Olga; Forrest, Stephen R.

    2013-12-01

    We demonstrate significant improvements in power conversion efficiency of bilayer organic photovoltaics by replacing the exciton-quenching MoO3 anode buffer layer with an exciton-blocking benzylphosphonic acid (BPA)-treated MoO3 or NiO layer. We show that the phosphonic acid treatment creates buffers that block up to 70% of excitons without sacrificing the hole extraction efficiency. Compared to untreated MoO3 anode buffers, BPA-treated NiO buffers exhibit a ˜ 25% increase in the near-infrared spectral response in diphenylanilo functionalized squaraine (DPSQ)/C60-based bilayer devices, increasing the power conversion efficiency under 1 sun AM1.5G simulated solar illumination from 4.8 ± 0.2% to 5.4 ± 0.3%. The efficiency can be further increased to 5.9 ± 0.3% by incorporating a highly conductive exciton blocking bathophenanthroline (BPhen):C60 cathode buffer. We find similar increases in efficiency in two other small-molecule photovoltaic systems, indicating the generality of the phosphonic acid-treated buffer approach to enhance exciton blocking.

  6. Kinetics of an acid-base catalyzed reaction (aspartame degradation) as affected by polyol-induced changes in buffer pH and pK values.

    PubMed

    Chuy, S; Bell, L N

    2009-01-01

    The kinetics of an acid-base catalyzed reaction, aspartame degradation, were examined as affected by the changes in pH and pK(a) values caused by adding polyols (sucrose, glycerol) to phosphate buffer. Sucrose-containing phosphate buffer solutions had a lower pH than that of phosphate buffer alone, which contributed, in part, to reduced aspartame reactivity. A kinetic model was introduced for aspartame degradation that encompassed pH and buffer salt concentrations, both of which change with a shift in the apparent pK(a) value. Aspartame degradation rate constants in sucrose-containing solutions were successfully predicted using this model when corrections (that is, lower pH, lower apparent pK(a) value, buffer dilution from the polyol) were applied. The change in buffer properties (pH, pK(a)) from adding sucrose to phosphate buffer does impact food chemical stability. These effects can be successfully incorporated into predictive kinetic models. Therefore, pH and pK(a) changes from adding polyols to buffer should be considered during food product development.

  7. Closed-form solutions of performability. [modeling of a degradable buffer/multiprocessor system

    NASA Technical Reports Server (NTRS)

    Meyer, J. F.

    1981-01-01

    Methods which yield closed form performability solutions for continuous valued variables are developed. The models are similar to those employed in performance modeling (i.e., Markovian queueing models) but are extended so as to account for variations in structure due to faults. In particular, the modeling of a degradable buffer/multiprocessor system is considered whose performance Y is the (normalized) average throughput rate realized during a bounded interval of time. To avoid known difficulties associated with exact transient solutions, an approximate decomposition of the model is employed permitting certain submodels to be solved in equilibrium. These solutions are then incorporated in a model with fewer transient states and by solving the latter, a closed form solution of the system's performability is obtained. In conclusion, some applications of this solution are discussed and illustrated, including an example of design optimization.

  8. DNA adsorption to and elution from silica surfaces: influence of amino acid buffers.

    PubMed

    Vandeventer, Peter E; Mejia, Jorge; Nadim, Ali; Johal, Malkiat S; Niemz, Angelika

    2013-09-19

    Solid phase extraction and purification of DNA from complex samples typically requires chaotropic salts that can inhibit downstream polymerase amplification if carried into the elution buffer. Amino acid buffers may serve as a more compatible alternative for modulating the interaction between DNA and silica surfaces. We characterized DNA binding to silica surfaces, facilitated by representative amino acid buffers, and the subsequent elution of DNA from the silica surfaces. Through bulk depletion experiments, we found that more DNA adsorbs to silica particles out of positively compared to negatively charged amino acid buffers. Additionally, the type of the silica surface greatly influences the amount of DNA adsorbed and the final elution yield. Quartz crystal microbalance experiments with dissipation monitoring (QCM-D) revealed multiphasic DNA adsorption out of stronger adsorbing conditions such as arginine, glycine, and glutamine, with DNA more rigidly bound during the early stages of the adsorption process. The DNA film adsorbed out of glutamate was more flexible and uniform throughout the adsorption process. QCM-D characterization of DNA elution from the silica surface indicates an uptake in water mass during the initial stage of DNA elution for the stronger adsorbing conditions, which suggests that for these conditions the DNA film is partly dehydrated during the prior adsorption process. Overall, several positively charged and polar neutral amino acid buffers show promise as an alternative to methods based on chaotropic salts for solid phase DNA extraction.

  9. Leaching with Penicillium simplicissimum: Influence of metals and buffers on proton extrusion and citric acid production

    SciTech Connect

    Franz, A.; Burgstaller, W.; Schinner, F. )

    1991-03-01

    In the presence of insoluble metal oxides (industrial filter dust, zinc oxide, synthetic mixture of metal oxides), Penicillium simplicissimum developed the ability to excrete considerable amounts of citric acid (>100 mM). Parallel with the increase of citric acid concentration in the culture broth, zinc was solubilized from zinc oxide. The adsorption of filter dust onto the mycelium (the pellets formed were less than 1 mm in diameter) was required for not only the citric acid excretion but also the leaching of zinc. When the filter dust was replaced with a synthetic mixture of metal oxides or with zinc oxide in combination with trace elements, levels of adsorption and citric acid production were observed to be similar to those in experiments where industrial filter dust was used. The two most important properties of the filter dust were its heavy-metal content and its buffering capacity. These properties were simulated by adding heavy metals in soluble form (as chlorides, sulfates, or nitrates) or soluble buffers to the medium. Both heavy metals and buffers were not able to induce a citric acid efflux. As with citric acid production by Aspergillus niger, the addition of manganese lowered citric acid excretion (by 40% with metal oxide-induced citric acid efflux and by 100% with urea-induced citric acid efflux). Copper antagonized the effect of manganese. The mechanism for the bulk of citric acid excretion by P. simplicissimum, however, seemed to be different from that described for citric acid accumulation by A. niger. Because of the inefficiency of metals in solubilized form and of soluble buffers to induce a strong citric acid efflux, adsorption of an insoluble metal compound (zinc oxide) turned out to be essential.

  10. A new strategy to stabilize oxytocin in aqueous solutions: I. The effects of divalent metal ions and citrate buffer.

    PubMed

    Avanti, Christina; Amorij, Jean-Pierre; Setyaningsih, Dewi; Hawe, Andrea; Jiskoot, Wim; Visser, Jan; Kedrov, Alexej; Driessen, Arnold J M; Hinrichs, Wouter L J; Frijlink, Henderik W

    2011-06-01

    In the current study, the effect of metal ions in combination with buffers (citrate, acetate, pH 4.5) on the stability of aqueous solutions of oxytocin was investigated. Both monovalent metal ions (Na(+) and K(+)) and divalent metal ions (Ca(2+), Mg(2+), and Zn(2+)) were tested all as chloride salts. The effect of combinations of buffers and metal ions on the stability of aqueous oxytocin solutions was determined by RP-HPLC and HP-SEC after 4 weeks of storage at either 4°C or 55°C. Addition of sodium or potassium ions to acetate- or citrate-buffered solutions did not increase stability, nor did the addition of divalent metal ions to acetate buffer. However, the stability of aqueous oxytocin in aqueous formulations was improved in the presence of 5 and 10 mM citrate buffer in combination with at least 2 mM CaCl(2), MgCl(2), or ZnCl(2) and depended on the divalent metal ion concentration. Isothermal titration calorimetric measurements were predictive for the stabilization effects observed during the stability study. Formulations in citrate buffer that had an improved stability displayed a strong interaction between oxytocin and Ca(2+), Mg(2+), or Zn(2+), while formulations in acetate buffer did not. In conclusion, our study shows that divalent metal ions in combination with citrate buffer strongly improved the stability of oxytocin in aqueous solutions.

  11. Solution Preserves Nucleic Acids in Body-Fluid Specimens

    NASA Technical Reports Server (NTRS)

    Pierson, Duane L.; Stowe, Raymond P.

    2004-01-01

    A solution has been formulated to preserve deoxyribonucleic acid (DNA) and ribonucleic acid (RNA) in specimens of blood, saliva, and other bodily fluids. Specimens of this type are collected for diagnostic molecular pathology, which is becoming the method of choice for diagnosis of many diseases. The solution makes it possible to store such specimens at room temperature, without risk of decomposition, for subsequent analysis in a laboratory that could be remote from the sampling location. Thus, the solution could be a means to bring the benefits of diagnostic molecular pathology to geographic regions where refrigeration equipment and diagnostic laboratories are not available. The table lists the ingredients of the solution. The functions of the ingredients are the following: EDTA chelates divalent cations that are necessary cofactors for nuclease activity. In so doing, it functionally removes these cations and thereby retards the action of nucleases. EDTA also stabilizes the DNA helix. Tris serves as a buffering agent, which is needed because minor contaminants in an unbuffered solution can exert pronounced effects on pH and thereby cause spontaneous degradation of DNA. SDS is an ionic detergent that inhibits ribonuclease activity. SDS has been used in some lysis buffers and as a storage buffer for RNA after purification. The use of the solution is straightforward. For example, a sample of saliva is collected by placing a cotton roll around in the subject's mouth until it becomes saturated, then the cotton is placed in a collection tube. Next, 1.5 mL of the solution are injected directly into the cotton and the tube is capped for storage at room temperature. The effectiveness of the solution has been demonstrated in tests on specimens of saliva containing herpes simplex virus. In the tests, the viral DNA, as amplified by polymerase chain reaction, was detected even after storage for 120 days.

  12. Process for defoaming acid gas scrubbing solutions and defoaming solutions

    SciTech Connect

    Ernst, E.R.; Robbins, M.L.

    1980-06-17

    The foam in acid gas scrubbing solutions created during an acid gas scrubbing process is reduced or eliminated by the addition of certain polyoxyethylene polyoxypropylene block copolymers as defoaming agents. The defoaming agents are particularly effective when the acid gas scrubbing solution contains an amine having a large hydrophobic moiety.

  13. A resin-buffered nutrient solution for controlling metal speciation in the algal bottle assay.

    PubMed

    Verheyen, L; Merckx, R; Smolders, E

    2012-06-15

    Metal speciation in solution is uncontrolled during algal growth in the traditional algal bottle assay. A resin-buffered nutrient solution was developed to overcome this problem and this was applied to test the effect of chloride (Cl⁻) on cadmium (Cd) uptake. Standard nutrient solution was enriched with 40 mM of either NaNO₃ or NaCl, and was prepared to contain equal Cd²⁺ but varying dissolved Cd due to the presence of CdCl(n)(2-n) complexes. Both solutions were subsequently used in an algal assay in 100 mL beakers that contained only the solution (designated "-R") or contained the solution together with a cation exchange sulfonate resin (2 g L⁻¹, designated "+R") as a deposit on the bottom of the beaker. Pseudokirchneriella subcapitata was grown for 72 h (1.4 × 10⁵-1.4 × 10⁶ cells mL⁻¹) in stagnant solution and shaken three times a day. Growth was unaffected by the presence of the resin (p>0.05). The Cd concentrations in solution of the -R devices decreased with 50-58% of initial values due to Cd uptake. No such changes were found in the +R devices or in abiotic controls. Cd uptake was unaffected by either NaNO₃ or NaCl treatment in the +R device, confirming that Cd²⁺ is the preferred Cd species in line with the general concept of metal bioavailability. In contrast, Cd uptake in the -R devices was two-fold larger in the NaCl treatment than in the NaNO₃ treatment (p<0.001), suggesting that CdCl(n)(2-n) complexes are bioavailable in this traditional set-up. However this bioavailability is partially, but not completely, an apparent one, because of the considerable depletion of solution ¹⁰⁹Cd in this set-up. Resin-buffered solutions are advocated in the algal bottle assay to control trace metal supply and to better identify the role of metal complexes on bioavailability.

  14. Effect of pH on the Electrochemical Behavior of Tantalum in Borate Buffer Solutions

    NASA Astrophysics Data System (ADS)

    Attarzadeh, F. R.; Attarzadeh, N.; Vafaeian, S.; Fattah-Alhosseini, A.

    2016-08-01

    In this research, various electrochemical methods were used to investigate the electrochemical behavior of tantalum in borate buffer solutions of various pH values, ranging from 9.0 to 6.5. Potentiodynamic polarization curves revealed that tantalum showed excellent passive behavior in borate buffer solutions. The potentiodynamic polarization and electrochemical impedance spectroscopy results showed that the passive film formed on tantalum offered its best protective behavior when the pH is 8.0, with the passivity undergoing a drastic change as the pH moved toward higher values. The semiconductive behavior of the passive films formed on tantalum was investigated by employing Mott-Schottky analysis in conjunction with a point defect model. The results indicated that the passive film exhibited n-type semiconductive behavior and that donor densities were in the range of 1.958-7.242 × 1020 cm-3. Moreover, this analysis showed that the donor density and flat band potential were quite sensitive to the pH.

  15. Development anmd testing of electrophoresis solutions. Task I.1: Development of optimal buffer system

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Two buffers were explored for testing: low ionic strength electrophoresis buffer with and without density gradient material. It was found that the electrophoresis routine was better tolerated when Ficoll was present. The results of a viability study of primary human fetal kidney (HFK-1) cells at the first passage are shown. Cell strain HFK-1 was used in several experiments at the first and second passage. The HFK consisted mainly of fibroblasts, and HFK-1 has a high epithelioid cell content. The chromosomes of HFK were examined and found to be euploid. The stock medium for cell electrophoresis is described. In this solution density gradient solutes such as sucrose and Ficoll are dissolved to bring the osmolarity to 0.30. Its ionic strength is less than 0.01M, and its conductivity is usually 0.0011 mho/cm. Methods for viability determination included direct microscopic counting of the percent cells attached and spread within 24 hr of plating test cultures or electrophoretically separated fractions. The Cytograf viability assay concept was tested, and shown that blue stained cells scatter less light into the 0.8 to 3.3 deg angular interval than do unstained cells.

  16. Effect of pH on the Electrochemical Behavior of Tantalum in Borate Buffer Solutions

    NASA Astrophysics Data System (ADS)

    Attarzadeh, F. R.; Attarzadeh, N.; Vafaeian, S.; Fattah-Alhosseini, A.

    2016-10-01

    In this research, various electrochemical methods were used to investigate the electrochemical behavior of tantalum in borate buffer solutions of various pH values, ranging from 9.0 to 6.5. Potentiodynamic polarization curves revealed that tantalum showed excellent passive behavior in borate buffer solutions. The potentiodynamic polarization and electrochemical impedance spectroscopy results showed that the passive film formed on tantalum offered its best protective behavior when the pH is 8.0, with the passivity undergoing a drastic change as the pH moved toward higher values. The semiconductive behavior of the passive films formed on tantalum was investigated by employing Mott-Schottky analysis in conjunction with a point defect model. The results indicated that the passive film exhibited n-type semiconductive behavior and that donor densities were in the range of 1.958-7.242 × 1020 cm-3. Moreover, this analysis showed that the donor density and flat band potential were quite sensitive to the pH.

  17. An investigation using atomic force microscopy nanoindentation of dental enamel demineralization as a function of undissociated acid concentration and differential buffer capacity

    NASA Astrophysics Data System (ADS)

    Barbour, Michele E.; Shellis, R. Peter

    2007-02-01

    Acidic drinks and foodstuffs can demineralize dental hard tissues, leading to a pathological condition known as dental erosion, which is of increasing clinical concern. The first step in enamel dissolution is a demineralization of the outer few micrometres of tissue, which results in a softening of the structure. The primary determinant of dissolution rate is pH, but the concentration of undissociated acid, which is related to buffer capacity, also appears to be important. In this study, atomic force microscopy nanoindentation was used to measure the first initial demineralization (softening) induced within 1 min by exposure to solutions with a range of undissociated acid concentration and natural pH of 3.3 or with an undissociated acid concentration of 10 mmol l-1 and pH adjusted to 3.3. The results indicate that differential buffering capacity is a better determinant of softening than undissociated acid concentration. Under the conditions of these experiments, a buffer capacity of >3 mmol l-1 pH-1 does not have any further effect on dissolution rate. These results imply that differential buffering capacity should be used for preference over undissociated acid concentration or titratable acidity, which are more commonly employed in the literature.

  18. Basics of base in hemodialysis solution: Dialysate buffer production, delivery and decontamination

    PubMed Central

    Desai, N.

    2015-01-01

    Hemodialysis requires the use of high volumes of freshly prepared, clean dialysate to foster the removal of low molecular weight metabolites (i.e., urea) and to correct the electrolyte and acid-base imbalance of chronic renal failure. Dialysate is produced by mixing clean, AAMI grade water with both an acid and base concentrate. This purpose of this report is to describe production, mixing and delivery of the buffer component of dialysate, and to also to address the cost, safety and feasibility of producing online bicarbonate. As endotoxin contaminated dialysate has been associated with the release of key mediators in acute and chronic inflammatory diseases associated with long-term hemodialysis therapy, aspects of disinfecting a bicarbonate delivery loop are also addressed. PMID:26199467

  19. Development of Solution Buffer Layers for RABiTS Based YBCO Coated Conductors

    SciTech Connect

    Paranthaman, Mariappan Parans; Qiu, Xiaofeng; Kim, Kyunghoon; Shi, D.; Zhang, Yifei; Li, Xiaoping; Sathyamurthy, Srivatsan; Thieme, C. L. H.; Rupich, M. W.

    2010-01-01

    The main objective of this research is to find a suitable alternate solution based seed layer for the standard RABiTS three-layer architecture of physical vapor deposited CeO2 cap/YSZ barrier/Y2O3 seed on Ni-5%W metal tape. In the present work, we have identified CeO2 buffer layer as a potential replacement for Y2O3 seeds. Using a metal-organic deposition (MOD) process, we have grown smooth, crack-free, epitaxial thin films of CeO2 (both pure and Zr, Cu and Gd-doped) directly on biaxially textured Ni-5W substrates in short lengths. Detailed XRD studies indicate that a single epitaxial CeO2 phase with slightly improved out-of-plane texture compared to the texture of underlying Ni-W substrates can be achieved in pure, undoped CeO2 samples. We have also demonstrated the growth of YSZ barrier layers on pure CeO2 seeds using sputtering. Both sputtered CeO2 cap layers and MOD-YBCO films were grown epitaxially on these YSZ-buffered MOD-CeO2/Ni-5W substrates. High critical currents per unit width, Ic of 264 A/cm (critical current density, Jc of 3.3 MA/cm2) at 77 K and 0.01 T was achieved for 0.8 m thick MOD-YBCO films grown on MOD-CeO2 seeds. These results indicate that CeO2 films can be grown directly on Ni-5W substrates and still support high performance YBCO coated conductors. This work holds promise for a route for producing low-cost buffer architecture for RABiTS based YBCO coated conductors.

  20. Development of Solution Buffer Layers for RABiTS Based YBCO Coated Conductors

    SciTech Connect

    Paranthaman, Mariappan Parans; Qiu, Xiaofeng; List III, Frederick Alyious; Zhang, Yifei; Li, Xiaoping; Sathyamurthy, Srivatsan; Thieme, C. L. H.; Rupich, M. W.

    2011-01-01

    Abstract The main objective of this research is to find a suitable alternate solution based seed layer for the standard RABiTS three-layer architecture of physical vapor deposited CeO cap/YSZ barrier/Y O seed on Ni-5%W metal tape. In the present work, we have identified CeO buffer layer as a potential replacement for Y O seeds. Using a metal-organic deposition (MOD) process, we have grown smooth, crack-free, epitaxial thin films of CeO (pure and Zr, Cu and Gd-doped) directly on biaxially textured Ni-5W substrates in short lengths. Detailed XRD studies indicate that a single epitaxial CeO phase with slightly improved out-of-plane texture compared to the texture of the underlying Ni-W substrates can be achieved in pure, undoped CeO samples. We have also demonstrated the growth of YSZ barrier layers on pure CeO seeds using sputtering. Both sputtered CeO cap layers and MOD-YBCO films were grown epitaxially on these YSZ-buffered MOD-CeO /Ni-5W substrates. High critical currents per unit width, of 264 A/cm (critical current density, of 3.3 MA/cm ) at 77 K and 0.01 T was achieved for 0.8 m thick MOD-YBCO films grown on MOD-CeO seeds. These results indicate that CeO films can be grown directly on Ni-5W substrates and still support high performance YBCO coated conductors. This work holds promise for a route for producing low-cost buffer architecture for RABiTS based YBCO coated conductors.

  1. Buffer Standards for the Biochemical pH of 3-(N-morpholino)-2-hydroxypropanesulfonic Acid from (278.15 to 328.15) K

    PubMed Central

    Roy, Lakshmi N.; Roy, Rabindra N.; Denton, Cole E.; LeNoue, Sean R.; Roy, Chandra N.; Ashkenazi, Shahaf; Fuge, Michael S.; Wollen, Joshua T.; Stegner, Jessica M.; Allen, Kathleen A.; Harmon, Meagan A.

    2009-01-01

    The values of the second dissociation constant pK2 and related thermodynamic quantities of the ampholyte 3-(N-morpholino)-2-hydroxypropanesulfonic acid (MOPSO) have been previously determined at temperatures from (278.15 to 328.15) K. In this study, the pH values of two buffer solutions without NaCl and three buffer solutions with NaCl having ionic strengths (I = 0.16 mol·kg−1) similar to those in blood plasma, have been evaluated at 12 temperatures from (278.15 to 328.15) K using an extended form of the Debye-Hückel equation, since the Bates-Guggenheim convention is valid up to I = 0.1 mol·kg−1. The liquid junction potentials (Ej) between the buffer solutions of MOPSO and saturated KCl solution of the calomel electrode at (298.15 and 310.15) K have been estimated by measurement with a flowing junction cell. These values of Ej have been used to ascertain the operational pH values at (298.15 and 310.15) K. Three buffer solutions of MOPSO are recommended as useful reference solutions for pH measurements in saline media of ionic strength I = 0.16 mol·kg−1. PMID:20160876

  2. Buffer Standards for the Biochemical pH of 3-(N-morpholino)-2-hydroxypropanesulfonic Acid from (278.15 to 328.15) K.

    PubMed

    Roy, Lakshmi N; Roy, Rabindra N; Denton, Cole E; Lenoue, Sean R; Roy, Chandra N; Ashkenazi, Shahaf; Fuge, Michael S; Wollen, Joshua T; Stegner, Jessica M; Allen, Kathleen A; Harmon, Meagan A

    2009-06-11

    The values of the second dissociation constant pK(2) and related thermodynamic quantities of the ampholyte 3-(N-morpholino)-2-hydroxypropanesulfonic acid (MOPSO) have been previously determined at temperatures from (278.15 to 328.15) K. In this study, the pH values of two buffer solutions without NaCl and three buffer solutions with NaCl having ionic strengths (I = 0.16 mol·kg(-1)) similar to those in blood plasma, have been evaluated at 12 temperatures from (278.15 to 328.15) K using an extended form of the Debye-Hückel equation, since the Bates-Guggenheim convention is valid up to I = 0.1 mol·kg(-1). The liquid junction potentials (E(j)) between the buffer solutions of MOPSO and saturated KCl solution of the calomel electrode at (298.15 and 310.15) K have been estimated by measurement with a flowing junction cell. These values of E(j) have been used to ascertain the operational pH values at (298.15 and 310.15) K. Three buffer solutions of MOPSO are recommended as useful reference solutions for pH measurements in saline media of ionic strength I = 0.16 mol·kg(-1).

  3. Dissolution properties of co-amorphous drug-amino acid formulations in buffer and biorelevant media.

    PubMed

    Heikkinen, A T; DeClerck, L; Löbmann, K; Grohganz, H; Rades, T; Laitinen, R

    2015-07-01

    Co-amorphous formulations, particularly binary drug-amino acid mixtures, have been shown to provide enhanced dissolution for poorly-soluble drugs and improved physical stability of the amorphous state. However, to date the dissolution properties (mainly intrinsic dissolution rate) of the co-amorphous formulations have been tested only in buffers and their supersaturation ability remain unexplored. Consequently, dissolution studies in simulated intestinal fluids need to be conducted in order to better evaluate the potential of these systems in increasing the oral bioavailability of biopharmaceutics classification system class II drugs. In this study, solubility and dissolution properties of the co-amorphous simvastatin-lysine, gibenclamide-serine, glibenclamide-threonine and glibenclamide-serine-threonine were studied in phosphate buffer pH 7.2 and biorelevant media (fasted and fed state simulated intestinal fluids (FaSSIF and FeSSIF, respectively)). The co-amorphous formulations were found to provide a long-lasting supersaturation and improve the dissolution of the drugs compared to the crystalline and amorphous drugs alone in buffer. Similar improvement, but in lesser extent, was observed in biorelevant media suggesting that a dissolution advantage observed in aqueous buffers may overestimate the advantage in vivo. However, the results show that, in addition to stability advantage shown earlier, co-amorphous drug-amino acid formulations provide dissolution advantage over crystalline drugs in both aqueous and biorelevant conditions.

  4. Total alkalinity versus buffer value (capacity) as a sensitivity indicator for fresh waters receiving acid rain

    SciTech Connect

    Faust, S.D.

    1983-09-01

    The frequently stated idea that total alkalinity is a measure of the buffer capacity of a natural water is refuted. Total alkalinity is a measure of the acid neutralizing capacity, equivalents/liter, of a water. In natural waters, the carbonate system provides most of this neutralizing capacity. In as much as the pH values of natural fresh waters lie below 8.3, the total alkalinity is, for all intents and purposes, the total bicarbonate content. Any contributions of carbonate and hydroxide to total alkalinity are nil. The buffer capacity or buffer value is the relation between the increment of a strong base, or strong acid, that causes a one unit change in the pH value. The values of total alkalinity and pH, considered individually cannot give an accurate assessment of the impact of acid deposition on a natural water. Rather it is necessary to combine the pH and alkalinity values into the beta concept in order to assess accurately and to calculate the capacity of a natural water to resist the impact of acid deposition. An analytical determination of total alkalinity is given with an application of the beta value. 17 references, 2 figures, 4 tables.

  5. Critical zinc[sup +2] activities for sour orange determined with chelator-buffered nutrient solutions

    SciTech Connect

    Swietlik, D.; Zhang, L. )

    1994-07-01

    Chelator-buffered nutrient solutions were used to study the effect of different levels of Zn activity in the rhizosphere on growth and nutritive responses of various tissues of sour orange seedlings. The seedlings were grown for 3 months in a growth chamber in a hydroponic culture containing from 5 to 69 [mu]m and 5 to 101 [mu]m total Zn in Expts. 1 and 2, respectively. Zn[sup +2] activities were calculated with a computerized chemical equilibrium model, and buffered by inclusion of a chelator, diethylenetriamine pentaacetate (DTPA), at 74 and 44 [mu]m in excess of the sum of Fe, Mn, Zn, Cu, Ni, and Co in Expts. 1 and 2, respectively. The use of DTPA-buffered solutions proved successful in imposing varying degrees of Zn deficiency. The deficiency was confirmed by leaf symptomatology, leaf chemical analyses, i.e., <16 mg[center dot]kg[sup [minus]1] Zn, and responses to foliar sprays and application of Zn to the roots. Growth parameters varied in their sensitivity to Zn deficiency, i.e., root dry weight < leaf number and white root growth < stem dry weight < leaf dry weight < shoot elongation and leaf area. The critical activities, expressed as pZn = [minus]log(Zn[sup +2]), were [approximately]10.2 [+-] 0.2 for root dry weight, 10.1 [+-] 0.2 for leaf number and white root growth, 10.0 [+-] 0.2 for stem dry weight, 9.9 [+-] 0.2 for leaf dry weight, and 9.8 [+-] 0.2 for shoot growth and leaf area. Increases in growth were observed in response to Zn applications even in the absence of visible Zn-deficiency symptoms. Seedlings containing > 23 mg[center dot]kg[sup [minus]1] Zn in leaves did not respond to further additions of Zn to the nutrient solution. Zinc foliar sprays were less effective than Zn applications to the roots in alleviating severe Zn deficiency because foliar-absorbed Zn was not translocated from the top of the roots and thus could not correct Zn deficiency in the roots.

  6. Influence of amino acids, buffers, and ph on the γ-irradiation-induced degradation of alginates.

    PubMed

    Ulset, Ann-Sissel T; Mori, Hideki; Dalheim, Marianne Ø; Hara, Masayuki; Christensen, Bjørn E

    2014-12-01

    Alginate-based biomaterials and medical devices are commonly subjected to γ-irradiation as a means of sterilization, either in the dry state or the gel (hydrated) state. In this process the alginate chains degrade randomly in a dose-dependent manner, altering alginates' material properties. The addition of free radical scavenging amino acids such as histidine and phenylalanine protects the alginate significantly against degradation, as shown by monitoring changes in the molecular weight distributions using SEC-MALLS and determining the pseudo first order rate constants of degradation. Tris buffer (0.5 M), but not acetate, citrate, or phosphate buffers had a similar effect on the degradation rate. Changes in pH itself had only marginal effects on the rate of alginate degradation and on the protective effect of amino acids. Contrary to previous reports, the chemical composition (M/G profile) of the alginates, including homopolymeric mannuronan, was unaltered following irradiation up to 10 kGy.

  7. The passivity of Type 316L stainless steel in borate buffer solution

    NASA Astrophysics Data System (ADS)

    Nicic, Igor; Macdonald, Digby D.

    2008-09-01

    The passivity of Type 316 SS in borate buffer solution (pH 8.35), in the steady-state, has been explored using a variety of electrochemical techniques, including potentiostatic polarization, Mott Schottky analysis, and electrochemical impedance spectroscopy. The study shows that the passive film is an n-type semiconductor with a donor density that is essentially independent of voltage across the passive state. The passive current density is also found to be voltage-independent, but the thickness of the barrier layer depends linearly on the applied voltage. These observations are consistent with the predictions of the Point Defect Model, noting that the point defects within the barrier layer of the passive film are metal interstitials or oxygen vacancies, or both. No evidence for p-type behavior was obtained, indicating that cation vacancies do not have a significant population density in the film compared with the two donors (cation interstitials and oxygen vacancies).

  8. Relationship between Virucidal Efficacy and Free Iodine Concentration of Povidone-Iodine in Buffer Solution.

    PubMed

    Wada, Hideki; Nojima, Yasuhiro; Ogawa, Satoko; Hayashi, Nobuyuki; Sugiyama, Noriyoshi; Kajiura, Takumi; Ueda, Tomofumi; Morimoto, Shota; Yokota, Katuhiro

    2016-01-01

    Povidone-iodine solutions prepared to various concentrations (0.01, 0.1, 1 and 10%) with 0.2M phosphate buffer (pH 7.0) (PVP-I PB) were analyzed to determine their free iodine concentrations using membrane permeation cells, and their inactivation effects on three viruses (influenza A virus, poliovirus type 1 and adenovirus type 3) were examined. The free iodine concentrations in the 0.01-10% PVP-I PB were determined to be 1.84, 4.88, 1.58 and 0.17 ppm (approximate values), respectively, with the maximum obtained for the 0.1% solution. The virucidal efficacy of these PVP-I PB against poliovirus type 1 and adenovirus type 3 was found to be generally dependent on free iodine concentration, with the 0.1% solution being the most effective. Influenza A virus was inactivated with an action time of 15 s at all four concentrations examined. The results of this study suggested an association between free iodine concentration and virucidal efficacy for the 0.01-10% PVP-I PB.

  9. Dephosphorization of Steelmaking Slag by Leaching with Acidic Aqueous Solution

    NASA Astrophysics Data System (ADS)

    Qiao, Yong; Diao, Jiang; Liu, Xuan; Li, Xiaosa; Zhang, Tao; Xie, Bing

    2015-12-01

    In the present paper, dephosphorization of steelmaking slag by leaching with acidic aqueous solution composed of citric acid, sodium hydroxide, hydrochloric acid and ion-exchanged water was investigated. The buffer solution of C6H8O7-NaOH-HCl system prevented changes in the pH values. Kinetic parameters including leaching temperature, slag particle size and pH values of the solution were optimized. The results showed that temperature has no obvious effect on the dissolution ratio of phosphorus. However, it has a significant effect on the dissolution ratio of iron. The dephosphorization rate increases with the decrease of slag particle size and the pH value of the solution. Over 90% of the phosphorus can be dissolved in the solution while the corresponding leaching ratio of iron was only 30% below the optimal condition. Leaching kinetics of dephosphorization follow the unreacted shrinking core model with a rate controlled step by the solid diffusion layer, the corresponding apparent activation energy being 1.233 kJ mol-1. A semiempirical kinetic equation was established. After leaching, most of the nC2S-C3P solid solution in the steelmaking slag was selectively dissolved in the aqueous solution and the iron content in the solid residue was correspondingly enriched.

  10. Dephosphorization of Steelmaking Slag by Leaching with Acidic Aqueous Solution

    NASA Astrophysics Data System (ADS)

    Qiao, Yong; Diao, Jiang; Liu, Xuan; Li, Xiaosa; Zhang, Tao; Xie, Bing

    2016-09-01

    In the present paper, dephosphorization of steelmaking slag by leaching with acidic aqueous solution composed of citric acid, sodium hydroxide, hydrochloric acid and ion-exchanged water was investigated. The buffer solution of C6H8O7-NaOH-HCl system prevented changes in the pH values. Kinetic parameters including leaching temperature, slag particle size and pH values of the solution were optimized. The results showed that temperature has no obvious effect on the dissolution ratio of phosphorus. However, it has a significant effect on the dissolution ratio of iron. The dephosphorization rate increases with the decrease of slag particle size and the pH value of the solution. Over 90% of the phosphorus can be dissolved in the solution while the corresponding leaching ratio of iron was only 30% below the optimal condition. Leaching kinetics of dephosphorization follow the unreacted shrinking core model with a rate controlled step by the solid diffusion layer, the corresponding apparent activation energy being 1.233 kJ mol-1. A semiempirical kinetic equation was established. After leaching, most of the nC2S-C3P solid solution in the steelmaking slag was selectively dissolved in the aqueous solution and the iron content in the solid residue was correspondingly enriched.

  11. ELECTROLYTIC REDUCTION OF NITRIC ACID SOLUTIONS

    DOEpatents

    Alter, H.W.; Barney, D.L.

    1958-09-30

    A process is presented for the treatment of radioactivc waste nitric acid solutions. The nitric acid solution is neutralized with an alkali metal hydroxide in an amount sufficient to precipitate insoluble hydroxides, and after separation of the precipitate the solution is electrolyzed to convert the alkali nitrate formed, to alkali hydroxide, gaseous ammonla and oxygen. The solution is then reusable after reducing the volume by evaporating the water and dissolved ammonia.

  12. Nitric acid recovery from waste solutions

    DOEpatents

    Wilson, A. S.

    1959-04-14

    The recovery of nitric acid from aqueous nitrate solutions containing fission products as impurities is described. It is desirable to subject such solutions to concentration by evaporation since nitric acid is regenerated thereby. A difficulty, however, is that the highly radioactive fission product ruthenium is volatilized together with the nitric acid. It has been found that by adding nitrous acid, ruthenium volatilization is suppressed and reduced to a negligible degree so that the distillate obtained is practically free of ruthenium.

  13. Preliminary observations of lung injury produced by instillation of HF in acidic and neutral buffer

    SciTech Connect

    Brainard, J.R.; Kinkead, S.A.; Kober, E.M.; Sebring, R.J.; Stavert, D.M.; Lehnert, B.E.

    1990-01-01

    Perfluoroisobutylene (PFIB) is an extremely toxic organofluoride that can be produced during pyrolysis of tetrafluoroethylene polymers, including Teflon{reg sign}. Inhalation of PFIB at very low concentrations causes acute lung injury, the hallmark of which is pulmonary edema. Several lines of evidence have suggested that hydrolysis of PFIB and resulting production of hydrofluoric acid may be responsible for pulmonary damage. In order to investigate the potential involvement of hydrofluoric acid in producing lung injury and its relationship to the mechanism of fluorocarbon toxicity, we have compared the pulmonary injury produced by PFIB, by dissociated (H{sup +} and F{sup {minus}}), and by undissociated (HF) hydrofluoric acid in the deep lung. By delivering hydrofluoric acid by intratracheal instillation in neutral buffer, we demonstrate that F{sup {minus}} produces no significant pulmonary injury as assessed by increased in lung weight and ultrastructural changes. Similarly, instillation of acid buffer alone demonstrated that H{sup +} did not produce detectable lung injury. Instillation of HF produced changes in lung weight and ultrastructure similar to those observed in PFIB-treated rats. However, the ultrastructural studies show that in contrast to inhalation of PFIB, which produces both endothelial and epithelial cell damage, instillation of HF appears to exert its injurious effects only upon epithelial cells. 9 refs., 1 fig.

  14. Sodium hydrosulfide improves the protective potential of the cardioplegic histidine buffer solution.

    PubMed

    Alves, Marco G; Soares, Ana F; Carvalho, Rui A; Oliveira, Paulo J

    2011-03-01

    Since H(2)S has an emerging role as a cardioprotector, we hypothesized that NaHS addition to the new cardioplegic histidine buffer solution (HBS) could improve its cardioprotective potential. Male Wistar-Han rat hearts were divided in 4 groups: i) control, ii) perfusion control (perfusion only), iii) 6h ischemia in HBS or in a modified-HBS with 100 μM of NaHS, a H(2)S donor, (HBSM) and iv) as iii followed by 30 min reperfusion. During ischemia, aliquots of the cardioplegic solution were collected for NMR analysis. Heart mitochondria respiration and transmembrane potential were measured after ischemia or after ischemia followed by reperfusion. Proteins involved in the apoptotic signaling pathway were also quantified in both mitochondrial and tissue samples. Cardiac mechanic performance was evaluated by measuring the heart rate and the left ventricular pressure. In HBSM-preserved hearts, a) glucose consumption increased as well as lactate and alanine production during ischemia, b) heart mitochondria presented an improved phosphorylative efficiency, including decreased phosphorylative lag phase for complex I and complex II substrates, c) mitochondrial and tissue p53, Bax and caspase-9 were lower and d) there was a more positive atrial chronotropic response than in HBS-preserved hearts. We concluded that the addition of NaHS to HBS enhances glycolysis during ischemia, decreases mitochondrial dysfunction, especially by preserving the phosphorylative system, prevents apoptosis and during ischemia/reperfusion.

  15. Buffer capacities of fresh water lakes sensitive to acid rain deposition

    SciTech Connect

    Faust, S.D.; McIntosh, A.

    1983-01-01

    The Van Slyke definition of buffer capacity, the increment of a strong base or strong acid that causes an incremental change in the pH value of water, is better than total alkalinity for defining a water's resistance to acid rain. This Van Slyke value, designated by beta, shows a peak at pH 6.3 for the bicarbonate-carbonate pair, indicating that the effect of acid rain on the pH and alkalinity of natural waters is not deleterious until this peak is traversed. A beta value of zero indicates a dead water with no capacity to neutralize acid. The beta values, pH and total alkalinity of lakes, reservoirs, and streams in New Jersey are given. Data clearly show that pH and alkalinity alone cannot determine buffer capacity. For example: Fairview Lake (pH of 5.5 and alkalinity of 10.2 mg per liter) has a beta value 11 times that of Clyde Potts Reservoir (pH of 7.3, alkalinity of 8.1 mg per liter). 3 references, 1 figure, 1 table.

  16. Solution nonideality related to solute molecular characteristics of amino acids.

    PubMed Central

    Keener, C R; Fullerton, G D; Cameron, I L; Xiong, J

    1995-01-01

    By measuring the freezing-point depression for dilute, aqueous solutions of all water-soluble amino acids, we test the hypothesis that nonideality in aqueous solutions is due to solute-induced water structuring near hydrophobic surfaces and solute-induced water destructuring in the dipolar electric fields generated by the solute. Nonideality is expressed with a single solute/solvent interaction parameter I, calculated from experimental measure of delta T. A related parameter, I(n), gives a method of directly relating solute characteristics to solute-induced water structuring or destructuring. I(n)-values correlate directly with hydrophobic surface area and inversely with dipolar strength. By comparing the nonideality of amino acids with progressively larger hydrophobic side chains, structuring is shown to increase with hydrophobic surface area at a rate of one perturbed water molecule per 8.8 square angstroms, implying monolayer coverage. Destructuring is attributed to dielectric realignment as described by the Debye-Hückel theory, but with a constant separation of charges in the amino-carboxyl dipole. By using dimers and trimers of glycine and alanine, this destructuring is shown to increase with increasing dipole strength using increased separation of fixed dipolar charges. The capacity to predict nonideal solution behavior on the basis of amino acid characteristics will permit prediction of free energy of transfer to water, which may help predict the energetics of folding and unfolding of proteins based on the characteristics of constituent amino acids. Images FIGURE 6 PMID:7711253

  17. Methyltrimethoxysilane-insulated piezoelectric microcantilevers for direct, all-electrical biodetection in buffered aqueous solutions

    NASA Astrophysics Data System (ADS)

    Capobianco, Joseph A.; Shih, Wan Y.; Shih, Wei-Heng

    2006-12-01

    We have examined coating (PbMg1/3Nb2/3O3)0.63-(PbTiO3)0.37 (PMN-PT)/tin piezoelectric microcantilever sensors (PEMSs) with a thin methyltrimethoxysilane (MTMS) by a simple solution method to electrically insulate the PEMS for biodetection in phosphate buffered saline (PBS) solutions. The PMN-PT/tin PEMSs were constructed using PMN-PT freestanding films that exhibited an electric-field-enhanced giant piezoelectric coefficient. The insulation procedure involved spin coatings of MTMS followed by cross-linking in water, which yielded a coating layer of about 10nm in thickness on the tin side of the PEMS. We showed that the MTMS-insulated PMN-PT/tin PEMSs were capable of electrical self-excitation and self-sensing with a stable resonance spectrum exhibiting a quality factor of Q =50 when submerged in 0.1M PBS solution. Direct, all-electrical, in situ detection of Escherichia coli O157:H7 at various concentrations was demonstrated at a flow rate of 0.5ml/min. A MTMS-insulated PMN-PT/tin PEMS 725μm long consisting of a 22-μm-thick PMN-PT layer and a 6-μm-thick tin layer exhibited a mass detection sensitivity Δm /Δf=-3±2×10-12g/Hz and a concentration sensitivity of better than 100cells/ml in less than 1ml of liquid.

  18. Gender-dependent metabolic remodeling during heart preservation in cardioplegic celsior and histidine buffer solution.

    PubMed

    Alves, Marco G; Oliveira, Pedro F; Martins, Fátima O; Oliveira, Paulo J; Carvalho, Rui A

    2012-08-01

    Understanding heart metabolism during preservation is crucial to develop new effective cardioplegic solutions. We aim to investigate metabolic alterations during heart preservation in the clinically used Celsior (Cs) and histidine buffer solution (HBS). We also focused in gender-specific metabolic adaptations during ischemia. We followed energy metabolism in hearts from males and females preserved during 6 hours in Cs and HBS. Hearts were subjected to cold ischemia (4°C) in Cs or HBS, and aliquots of the cardioplegic solution were collected throughout preservation for nuclear magnetic resonance analysis. HBS-preserved hearts from males consumed glucose mostly between 240 and 360 minutes, whereas HBS-preserved hearts from females consumed glucose throughout the 6 hours of ischemia. Lactate production rates followed approximately the glucose consumption rates in HBS-preserved hearts. The lactate to alanine ratio, an indicator of the redox state, was increased in HBS-preserved hearts when compared with Cs-preserved hearts. Hearts from males presented a higher redox state than those from females preserved in Cs after 300 minutes. Both Cs and HBS were capable of preventing acidification in hearts from females but not in hearts from males, which decreased the extracellular pH. HBS-preserved hearts from males and females produced 0.1 ± 0.01 and 0.15 ± 0.03 μmol·min·gdw of lactate, respectively. Those rates were significantly higher than in Cs-preserved hearts. Thus, Cs was more effective in preventing lactate production. We conclude that glycolysis and lactate production are stimulated in HBS-preserved hearts. HBS shows better overall results particularly in hearts from females, which presented less extracellular acidification and were more effective in recycling the metabolic subproducts.

  19. Acid-base buffering of soils in transitional and transitional-accumulative positions of undisturbed southern-taiga landscapes

    NASA Astrophysics Data System (ADS)

    Rusakova, E. S.; Ishkova, I. V.; Tolpeshta, I. I.; Sokolova, T. A.

    2012-05-01

    The method of continuous potentiometric titration (CPT) of soil water suspensions was used to evaluate the acid-base buffering of samples from the major genetic horizons of podzolic soils on a slope and soddy gley soils on the adjacent floodplain of a rivulet. In the soils of the slope, the buffering to acid upon titration from the pH of the initial titration point (ITP) to pH 3 in all the horizons was 1.5-2.0 times lower than that in the podzolic soils of the leveled interfluve, which could be due to the active leaching of exchangeable bases and oxalate-soluble aluminum and iron compounds with the later soil flows. In the soddy gley soils, the buffering to acid in the mineral horizons was 2-10 times higher than that in the podzolic soils. A direct dependence of the soil buffering to acid on the total content of exchangeable bases and on the content of oxalate-soluble aluminum compounds was found. A direct dependence of the buffering to basic upon titration from the ITP to pH 10 on the contents of the oxalate-soluble aluminum and organic matter was observed in the mineral horizons of all the studied soils. The soil treatment with Tamm's reagent resulted in the decrease of the buffering to acid in the soddy gley soils of the floodplain, as well as in the decrease of the buffering to basic in the soils on the slopes and in the soddy gley soils. It was also found that the redistribution of the mobile aluminum compounds between the eluvial, transitional, and transitional-accumulative positions in the undisturbed southern taiga landscapes leads to significant spatial differentiation of the acid-base buffering of the mineral soil horizons with a considerable increase in the buffer capacity of the soils within the transitional-accumulative terrain positions.

  20. Contributions of separate reactions to the acid-base buffering of soils in brook floodplains (Central Forest State Reserve)

    NASA Astrophysics Data System (ADS)

    Sokolova, T. A.; Tolpeshta, I. I.; Rusakova, E. S.

    2016-04-01

    The acid-base buffering of gleyic gray-humus soils developed in brook floodplains and undisturbed southern-taiga landscapes has been characterized by the continuous potentiometric titration of soil water suspensions. During the interaction with an acid, the major amount of protons (>80%) is consumed for the displacement of exchangeable bases and the dissolution of Ca oxalates. In the O and AY horizons, Mn compounds make the major contribution (2-15%) to the acid buffering. The buffer reactions with the participation of Al compounds make up from 0.5 to 1-2% of the total buffering capacity, and the protonation of the surface OH groups of kaolinite consumes 2-3% of the total buffering capacity. The deprotonation of OH groups on the surface of Fe hydroxides (9-43%), the deprotonation of OH groups on the surface of illite crystals (3-19%), and the dissolution of unidentified aluminosilicates (9-14%) are the most significant buffer reactions whose contributions have been quantified during the interaction with a base. The contribution of the deprotonation of OH groups on the surface of kaolinite particles is lower (1-5%) because of the small specific surface area of this mineral, and that of the dissolution of Fe compounds is insignificant. In the AY horizon, the acid and base buffering of soil in the rhizosphere is higher than beyond the rhizosphere because of the higher contents of organic matter and nonsilicate Fe and Al compounds.

  1. Acid-base and respiratory properties of a buffered bovine erythrocyte perfusion medium.

    PubMed

    Lindinger, M I; Heigenhauser, G J; Jones, N L

    1986-05-01

    Current research in organ physiology often utilizes in situ or isolated perfused tissues. We have characterized a perfusion medium associated with excellent performance characteristics in perfused mammalian skeletal muscle. The perfusion medium consisting of Krebs-Henseleit buffer, bovine serum albumin, and fresh bovine erythrocytes was studied with respect to its gas-carrying relationships and its response to manipulation of acid-base state. Equilibration of the perfusion medium at base excess of -10, -5, 0, 5, and 10 mmol X L-1 to humidified gas mixtures varying in their CO2 and O2 content was followed by measurements of perfusate hematocrit, hemoglobin concentration, pH, Pco2, Cco2, Po2, and percent oxygen saturation. The oxygen dissociation curve was similar to that of mammalian bloods, having a P50 of 32 Torr (1 Torr = 133.3 Pa), Hill's constant n of 2.87 +/- 0.15, and a Bohr factor of -0.47, showing the typical Bohr shifts with respect to CO2 and pH. The oxygen capacity was calculated to be 190 mL X L-1 blood. The carbon dioxide dissociation curve was also similar to that of mammalian blood. The in vitro nonbicarbonate buffer capacity (delta [HCO3-] X delta pH-1) at zero base excess was -24.6 and -29.9 mmol X L-1 X pH-1 for the perfusate and buffer, respectively. The effects of reduced oxygen saturation on base excess and pH of the medium were quantified. The data were used to construct an acid-base alignment diagram for the medium, which may be used to quantify the flux of nonvolatile acid or base added to the venous effluent during tissue perfusions.

  2. Graphene ultrathin film electrode for detection of lead ions in acetate buffer solution.

    PubMed

    Wang, Zhaomeng; Liu, Erjia

    2013-01-15

    Few-layer graphene ultrathin films were synthesized via solid-state carbon diffusion from amorphous carbon (a-C) thin layers sputtering coated on Si substrates with or without a SiO(2) layer, which an a-C layer was covered by a nickel (Ni) layer as a catalyst. When the Ni/a-C bilayer coated samples were heated at 1000°C the carbon (C) atoms from the a-C layers diffused into the top Ni layers to form a C rich surface. Upon rapid cooling, the C atoms accumulated on the surface of the Ni layers and formed graphene ultrathin films through nucleation and growth processes. The formation of graphene ultrathin films was confirmed by Raman spectroscopy, high resolution transmission electron microscopy (HR-TEM), electron diffraction, field-emission scanning electron microscopy (FE-SEM) and 4-point probe. The synthesized graphene ultrathin films were used as working electrodes for detection of trace heavy metal ions (Pb(2+), as low as 7 nM) in acetate buffer solutions (pH 5.3) using square wave anodic stripping voltammetry (SWASV). The effects of substrate surface condition and Ni layer thickness on the structure and electrochemical properties of graphene ultrathin film electrodes were investigated in detail. Compared to conventional diamond-like carbon (DLC) electrodes, the graphene electrodes developed in this study had better repeatability, higher sensitivity and higher resistance to passivation caused by surface active species.

  3. Substituent Effects on the Photodeprotection Reactions of Selected Ketoprofen Derivatives in Phosphate Buffered Aqueous Solutions

    PubMed Central

    Liu, Mingyue; Li, Ming-De; Huang, Jinqing; Li, Tianlu; Liu, Han; Li, Xuechen; Phillips, David Lee

    2016-01-01

    Photodeprotection is an important reaction that has been attracting broad interest for use in a variety of applications. Recent advances in ultrafast and vibrational time-resolved spectroscopies can facilitate obtaining data to help unravel the reaction mechanisms involving in the photochemical reactions of interest. The kinetics and reaction mechanisms for the photodeprotection reactions of ketoprofen derivatives containing three different substituents (ibuprofen, Br and I) were investigated by femtosecond transient absorption (fs-TA) and nanosecond time-resolved resonance Raman (ns-TR3) spectroscopy methods in phosphate buffered solutions (PBS). Fs-TA allows us to detect the decay kinetics of the triplet species as the key precursor for formation of a carbanion species for three different substituents attached to ketoprofen. To characterize the structural and electronic properties of the corresponding carbanion and triplet intermediates, TR3 spectroscopic experiments were conducted. The transient spectroscopy work reveals that the different substituents affect the photodecarboxylation reaction to produce carbon dioxide which in turn influences the generation of the carbanion species which determines the rate of the photorelease of the functional groups attached on the ketoprofen parent molecule. The fingerprint TR3 spectroscopy results suggest that ketoprofen derivatives may be deactivated to produce a triplet carbanion when increasing the atom mass of the halogen atoms. PMID:26899243

  4. Monolayer formation of luminescent germanium nanoparticles on silica surface in aqueous buffer solution.

    PubMed

    Shirahata, Naoto

    2014-03-01

    The present paper reports monolayer formation of germanium nanoparticles (Ge NPs) on silica substrate. The NPs were prepared by hydride reduction of GeCl4, which is encapsulated with an inverse micelle of dimethyldioctylammonium bromide, with lithium aluminum hydride, and subsequent hydrogermylation of allylamine in the presence of platinum catalyst. The resultant NPs showed the blue photoluminescence property. Due to the terminal amine, the NPs were soluble highly in aqueous buffer solution. To fabricate a monolayer of Ge NPs, the chemical reactivity of the NPs was studied using a multi-functional microarray in which different kinds of siloxane monolayers were periodically aligned on a silica substrate. We observed using fluorescence microscope whether the terminal amines of the NPs recognize the specific monolayers in the microarray. In terms of fluorescence observation, the entire surface of the monolayer-covered microsize-domains emits uniformly the blue light. This suggests a high degree of coverage of the luminescent NPs covering over the monolayer regions in the microarray, and implies the non-occurrence of quenching through energy transfer between adjacent NPs.

  5. Substituent Effects on the Photodeprotection Reactions of Selected Ketoprofen Derivatives in Phosphate Buffered Aqueous Solutions

    NASA Astrophysics Data System (ADS)

    Liu, Mingyue; Li, Ming-De; Huang, Jinqing; Li, Tianlu; Liu, Han; Li, Xuechen; Phillips, David Lee

    2016-02-01

    Photodeprotection is an important reaction that has been attracting broad interest for use in a variety of applications. Recent advances in ultrafast and vibrational time-resolved spectroscopies can facilitate obtaining data to help unravel the reaction mechanisms involving in the photochemical reactions of interest. The kinetics and reaction mechanisms for the photodeprotection reactions of ketoprofen derivatives containing three different substituents (ibuprofen, Br and I) were investigated by femtosecond transient absorption (fs-TA) and nanosecond time-resolved resonance Raman (ns-TR3) spectroscopy methods in phosphate buffered solutions (PBS). Fs-TA allows us to detect the decay kinetics of the triplet species as the key precursor for formation of a carbanion species for three different substituents attached to ketoprofen. To characterize the structural and electronic properties of the corresponding carbanion and triplet intermediates, TR3 spectroscopic experiments were conducted. The transient spectroscopy work reveals that the different substituents affect the photodecarboxylation reaction to produce carbon dioxide which in turn influences the generation of the carbanion species which determines the rate of the photorelease of the functional groups attached on the ketoprofen parent molecule. The fingerprint TR3 spectroscopy results suggest that ketoprofen derivatives may be deactivated to produce a triplet carbanion when increasing the atom mass of the halogen atoms.

  6. Graphene ultrathin film electrode for detection of lead ions in acetate buffer solution.

    PubMed

    Wang, Zhaomeng; Liu, Erjia

    2013-01-15

    Few-layer graphene ultrathin films were synthesized via solid-state carbon diffusion from amorphous carbon (a-C) thin layers sputtering coated on Si substrates with or without a SiO(2) layer, which an a-C layer was covered by a nickel (Ni) layer as a catalyst. When the Ni/a-C bilayer coated samples were heated at 1000°C the carbon (C) atoms from the a-C layers diffused into the top Ni layers to form a C rich surface. Upon rapid cooling, the C atoms accumulated on the surface of the Ni layers and formed graphene ultrathin films through nucleation and growth processes. The formation of graphene ultrathin films was confirmed by Raman spectroscopy, high resolution transmission electron microscopy (HR-TEM), electron diffraction, field-emission scanning electron microscopy (FE-SEM) and 4-point probe. The synthesized graphene ultrathin films were used as working electrodes for detection of trace heavy metal ions (Pb(2+), as low as 7 nM) in acetate buffer solutions (pH 5.3) using square wave anodic stripping voltammetry (SWASV). The effects of substrate surface condition and Ni layer thickness on the structure and electrochemical properties of graphene ultrathin film electrodes were investigated in detail. Compared to conventional diamond-like carbon (DLC) electrodes, the graphene electrodes developed in this study had better repeatability, higher sensitivity and higher resistance to passivation caused by surface active species. PMID:23200357

  7. Characterization of metal ion-nucleic acid interactions in solution.

    PubMed

    Pechlaner, Maria; Sigel, Roland K O

    2012-01-01

    Metal ions are inextricably involved with nucleic acids due to their polyanionic nature. In order to understand the structure and function of RNAs and DNAs, one needs to have detailed pictures on the structural, thermodynamic, and kinetic properties of metal ion interactions with these biomacromolecules. In this review we first compile the physicochemical properties of metal ions found and used in combination with nucleic acids in solution. The main part then describes the various methods developed over the past decades to investigate metal ion binding by nucleic acids in solution. This includes for example hydrolytic and radical cleavage experiments, mutational approaches, as well as kinetic isotope effects. In addition, spectroscopic techniques like EPR, lanthanide(III) luminescence, IR and Raman as well as various NMR methods are summarized. Aside from gaining knowledge about the thermodynamic properties on the metal ion-nucleic acid interactions, especially NMR can be used to extract information on the kinetics of ligand exchange rates of the metal ions applied. The final section deals with the influence of anions, buffers, and the solvent permittivity on the binding equilibria between metal ions and nucleic acids. Little is known on some of these aspects, but it is clear that these three factors have a large influence on the interaction between metal ions and nucleic acids.

  8. The formation of stable pH gradients with weak monovalent buffers for isoelectric focusing in free solution

    NASA Technical Reports Server (NTRS)

    Mosher, Richard A.; Thormann, Wolfgang; Graham, Aly; Bier, Milan

    1985-01-01

    Two methods which utilize simple buffers for the generation of stable pH gradients (useful for preparative isoelectric focusing) are compared and contrasted. The first employs preformed gradients comprised of two simple buffers in density-stabilized free solution. The second method utilizes neutral membranes to isolate electrolyte reservoirs of constant composition from the separation column. It is shown by computer simulation that steady-state gradients can be formed at any pH range with any number of components in such a system.

  9. An exploratory study into students' conceptual understanding of acid/base principles associated with chemical buffer systems

    NASA Astrophysics Data System (ADS)

    MacGowan, Catherine Elizabeth

    The overall objective of this research project was to provide an insight into students' conceptual understanding of acid/base principles as it relates to the comprehension and correct application of scientific concepts during a problem-solving activity. The difficulties experienced learning science and in developing appropriate problem-solving strategies most likely are predetermined by students' existing conceptual and procedural knowledge constructs; with the assimilation of newly acquired knowledge hindering or aiding the learning process. Learning chemistry requires a restructuring of content knowledge which will allow the individual to assemble and to integrate his/her own perception of science with instructional knowledge. The epistemology of constructivism, the theoretical grounding for this research project, recognizes the student's role as an active participant in the learning process. The study's design was exploratory in nature and descriptive in design. The problem-solving activity, the preparation of a chemical buffer solution at pH of 9, was selected and modified to reflect and meet the study's objective. Qualitative research methods (i.e., think aloud protocols, retrospective interviews, survey questionnaires such as the Scale of Intellectual Development (SID), and archival data sources) were used in the collection and assessment of data. Given its constructivist grounding, simplicity, and interpretative view of knowledge acquisition and learning of collegiate aged individuals, the Perry Intellectual and Ethical Development Model (1970) was chosen as the applied model for evaluation student cognition. The study's participants were twelve traditional college age students from a small, private liberal arts college. All participants volunteered for the project and had completed or were completing a general college chemistry course at the time of the project. Upon analysis of the data the following observations and results were noted: (1) students

  10. Plasma levels of acetylsalicylic acid and salicylic acid after oral ingestion of plain and buffered acetylsalicylic acid in relation to bleeding time and thrombocyte function.

    PubMed

    Proost, J H; Van Imhoff, G W; Wesseling, H

    1983-02-25

    Buffered acetylsalicylic acid (Alka Seltzer, B-ASA) and plain aspirin (P-ASA) tablets were compared as to their effects on bleeding time and platelet function in eight healthy male volunteers. Two doses (500 and 1000 mg) of each preparation were investigated in a cross-over design, each volunteer being his own control in each dose group (n=4). Both preparations disturbed platelet aggregation to the same extent. Bleeding time increased after both preparations, though significantly more after the buffered preparation than after plain acetylsalicylic acid, irrespective of the dosage. The 1000 mg dose prolonged bleeding time significantly more than the 500 mg dose, irrespective of the preparation. Kinetic analysis showed that B-ASA gave higher peak plasma levels of acetylsalicylic acid (ASA) and accordingly salicylic acid peak levels were also higher after the buffered preparation. It is concluded that B-ASA in equi-analgesic doses prolongs bleeding time more than the plain preparation. Since it is less agressive on the gastro-intestinal mucosa, its use may be advantageous in situations where acetylsalicylic acid induced loss of platelet aggregation is desired. However, the risk of prolonged bleeding--e.g. after tooth extractions--is probably higher after the buffered preparation. PMID:6844122

  11. Buffer capacity of biologics--from buffer salts to buffering by antibodies.

    PubMed

    Karow, Anne R; Bahrenburg, Sven; Garidel, Patrick

    2013-01-01

    Controlling pH is essential for a variety of biopharmaceutical process steps. The chemical stability of biologics such as monoclonal antibodies is pH-dependent and slightly acidic conditions are favorable for stability in a number of cases. Since control of pH is widely provided by added buffer salts, the current study summarizes the buffer characteristics of acetate, citrate, histidine, succinate, and phosphate buffers. Experimentally derived values largely coincide with values calculated from a model that had been proposed in 1922 by van Slyke. As high concentrated protein formulations become more and more prevalent for biologics, the self-buffering potential of proteins becomes of relevance. The current study provides information on buffer characteristics for pH ranges down to 4.0 and up to 8.0 and shows that a monoclonal antibody at 50 mg/mL exhibits similar buffer capacity as 6 mM citrate or 14 mM histidine (pH 5.0-6.0). Buffer capacity of antibody solutions scales linearly with protein concentration up to more than 200 mg/mL. At a protein concentration of 220 mg/mL, the buffer capacity resembles the buffer capacity of 30 mM citrate or 50 mM histidine (pH 5.0-6.0). The buffer capacity of monoclonal antibodies is practically identical at the process relevant temperatures 5, 25, and 40°C. Changes in ionic strength of ΔI=0.15, in contrast, can alter the buffer capacity up to 35%. In conclusion, due to efficient self-buffering by antibodies in the pH range of favored chemical stability, conventional buffer excipients could be dispensable for pH stabilization of high concentrated protein solutions.

  12. Influence of amino acids, buffers, and ph on the γ-irradiation-induced degradation of alginates.

    PubMed

    Ulset, Ann-Sissel T; Mori, Hideki; Dalheim, Marianne Ø; Hara, Masayuki; Christensen, Bjørn E

    2014-12-01

    Alginate-based biomaterials and medical devices are commonly subjected to γ-irradiation as a means of sterilization, either in the dry state or the gel (hydrated) state. In this process the alginate chains degrade randomly in a dose-dependent manner, altering alginates' material properties. The addition of free radical scavenging amino acids such as histidine and phenylalanine protects the alginate significantly against degradation, as shown by monitoring changes in the molecular weight distributions using SEC-MALLS and determining the pseudo first order rate constants of degradation. Tris buffer (0.5 M), but not acetate, citrate, or phosphate buffers had a similar effect on the degradation rate. Changes in pH itself had only marginal effects on the rate of alginate degradation and on the protective effect of amino acids. Contrary to previous reports, the chemical composition (M/G profile) of the alginates, including homopolymeric mannuronan, was unaltered following irradiation up to 10 kGy. PMID:25412478

  13. Acid-extrusion from tissue: the interplay between membrane transporters and pH buffers.

    PubMed

    Hulikova, Alzbeta; Harris, Adrian L; Vaughan-Jones, Richard D; Swietach, Pawel

    2012-01-01

    The acid-base balance of cells is related to the concentration of free H⁺ ions. These are highly reactive, and their intracellular concentration must be regulated to avoid detrimental effects to the cell. H⁺ ion dynamics are influenced by binding to chelator substances ('buffering'), and by the production, diffusion and membrane-transport of free H⁺ ions or of the H⁺-bound chelators. Intracellular pH (pHi) regulation aims to balance this system of diffusion-reaction-transport processes at a favourable steady-state pHi. The ability of cells to regulate pHi may set a limit to tissue growth and can be subject to selection pressures. Cancer cells have been postulated to respond favourably to such selection pressures by evolving a better means of pHi regulation. A particularly important feature of tumour pHi regulation is acid-extrusion, which involves H⁺-extrusion and HCO₃⁻-uptake by membrane-bound transporter-proteins. Extracellular CO₂/HCO₃⁻ buffer facilitates these membrane-transport processes. As a mobile pH-buffer, CO₂/HCO₃⁻ protects the extracellular space from excessive acidification that could otherwise inhibit further acid-extrusion. CO₂/HCO₃⁻ also provides substrate for HCO₃⁻-transporters. However, the inherently slow reaction kinetics of CO₂/HCO₃⁻ can be rate-limiting for acid-extrusion. To circumvent this, cells can express extracellular-facing carbonic anhydrase enzymes to accelerate the attainment of equilibrium between CO₂, HCO₃⁻ and H⁺. The acid-extrusion apparatus has been proposed as a target for anti-cancer therapy. The major targets include H⁺ pumps, Na⁺/H⁺ exchangers and carbonic anhydrases. The effectiveness of such therapy will depend on the correct identification of rate-limiting steps in pHi regulation in a specific type of cancer. PMID:22360560

  14. Separation of oligonucleotides of identical size, but different base composition, by free zone capillary electrophoresis in strongly acidic, isoelectric buffers.

    PubMed

    Perego, M; Gelfi, C; Stoyanov, A V; Righetti, P G

    1997-12-01

    A novel method for analyzing oligonucleotides of the same length, but bearing a single base substitution, is reported, based on free zone capillary electrophoresis (CZE) under rather acidic pH values. For this purpose, a set of four 18-mers of fairly random base composition has been synthesized, bearing, in nucleotide 9, the following bases: T, C, G or A. Theoretical predictions, based on titration curves of single free nucleotides, allowed us to predict that the simultaneous separation of a mixture of all four oligonucleotides could be possible in a pH 3-4 window. In fact, electrophoresis at pH 5.7 gave a single, asymmetric peak, whereas CZE at pH 4.8 could resolve three out of four species (the T9 and G9 oligonucleotides co-migrating into a single zone). A unique separation power could be obtained at pH 3.3 in a buffer comprising an amphoteric species (isoelectric iminodiacetic acid, IDA) and 7 M urea. Although IDA exhibited a pI of 2.23 (for a 100 mM solution), the addition of 7 M urea (necessary to denature the oligonucleotides) raised the apparent pH of the solution to 3.3. PMID:9504830

  15. The use of ethylene glycol solution as the running buffer for highly efficient microchip-based electrophoresis in unmodified cyclic olefin copolymer microchips.

    PubMed

    Wang, Qin; Zhang, Yuan; Ding, Hui; Wu, Jing; Wang, Lili; Zhou, Lei; Pu, Qiaosheng

    2011-12-30

    An ethylene glycol solution was used as the electrophoretic running buffer in unmodified cyclic olefin copolymer (COC) microchips to minimize the interactions between the analytes and the hydrophobic walls of the plastic microchannels, enhance the resolution of the analytes and eliminate the uncontrollable dispersion caused by uneven liquid levels and non-uniform surfaces of the separation channels. Five amino acids that were labeled with fluorescein isothiocyanate (FITC) were used as model analytes to examine the separation efficiency. The effects of ethylene glycol concentration, pH and sodium tetraborate concentration were systematically investigated. The five FITC-labeled amino acids were effectively resolved using a COC microchip with an effective length of 2.5 cm under optimum conditions, which included using a running buffer of 20 mmol/L sodium tetraborate in ethylene glycol:water (80:20, v/v), pH 6.7. A theoretical plate number of 4.8 × 10(5)/m was obtained for aspartic acid. The system exhibited good repeatability, and the relative standard deviations (n=5) of the peak areas and migration times were no more than 3.4% and 0.7%, respectively. Furthermore, the system was successfully applied to elucidate these five amino acids in human saliva.

  16. The stability of DLC film on nitrided CoCrMo alloy in phosphate buffer solution

    NASA Astrophysics Data System (ADS)

    Zhang, T. F.; Liu, B.; Wu, B. J.; Liu, J.; Sun, H.; Leng, Y. X.; Huang, N.

    2014-07-01

    CoCrMo alloy is often used as the material for metal artificial joint, but metal debris and metal ions are the main concern on tissue inflammation or tissue proliferation for metal prosthesis. In this paper, nitrogen ion implantation and diamond like carbon (DLC) film composite treatment was used to reduce the wear and ion release of biomedical CoCrMo substrate. The mechanical properties and stability of N-implanted/DLC composite layer in phosphate buffer solution (PBS) was evaluated to explore the full potential of N-implanted/DLC composite layer as an artificial joint surface modification material. The results showed that the DLC film on N implanted CoCrMo (N-implanted/DLC composite layer) had the higher surface hardness and wear resistance than the DLC film on virgin CoCrMo alloy, which was resulted from the strengthen effect of the N implanted layer on CoCrMo alloy. After 30 days immersion in PBS, the structure of DLC film on virgin CoCrMo or on N implanted CoCrMo had no visible change. But the adhesion and corrosion resistance of DLC on N implanted CoCrMo (N-implanted/DLC composite layer) was weakened due to the dissolution of the N implanted layer after 30 days immersion in PBS. The adhesion reduction of N-implanted/DLC composite layer was adverse for in vivo application in long term. So researcher should be cautious to use N implanted layer as an inter-layer for increasing CoCrMo alloy load carrying capacity in vivo environment.

  17. A nitrilo-tri-acetic-acid/acetic acid route for the deposition of epitaxial cerium oxide films as high temperature superconductor buffer layers

    SciTech Connect

    Thuy, T.T.; Lommens, P.; Narayanan, V.; Van de Velde, N.; De Buysser, K.; Herman, G.G.; Cloet, V.; Van Driessche, I.

    2010-09-15

    A water based cerium oxide precursor solution using nitrilo-tri-acetic-acid (NTA) and acetic acid as complexing agents is described in detail. This precursor solution is used for the deposition of epitaxial CeO{sub 2} layers on Ni-5at%W substrates by dip-coating. The influence of the complexation behavior on the formation of transparent, homogeneous solutions and gels has been studied. It is found that ethylenediamine plays an important role in the gelification. The growth conditions for cerium oxide films were Ar-5% gas processing atmosphere, a solution concentration level of 0.25 M, a dwell time of 60 min at 900 {sup o}C and 5-30 min at 1050 {sup o}C. X-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscopy (AFM), pole figures and spectroscopic ellipsometry were used to characterize the CeO{sub 2} films with different thicknesses. Attenuated total reflection-Fourier transform infrared (ATR-FTIR) was used to determine the carbon residue level in the surface of the cerium oxide film, which was found to be lower than 0.01%. Textured films with a thickness of 50 nm were obtained. - Graphical abstract: Study of the complexation and hydrolysis behavior of Ce{sup 4+} ions in the presence of nitrilo-tri-acetic acid and the subsequent development of an aqueous chemical solution deposition route suited for the processing of textured CeO{sub 2} buffer layers on Ni-W tapes.

  18. Artificially MoO3 graded ITO anodes for acidic buffer layer free organic photovoltaics

    NASA Astrophysics Data System (ADS)

    Lee, Hye-Min; Kim, Seok-Soon; Kim, Han-Ki

    2016-02-01

    We report characteristics of MoO3 graded ITO anodes prepared by a RF/DC graded sputtering for acidic poly(3,4-ethylene dioxylene thiophene):poly(styrene sulfonic acid) (PEDOT:PSS)-free organic solar cells (OSCs). Graded sputtering of the MoO3 buffer layer on top of the ITO layer produced MoO3 graded ITO anodes with a sheet resistance of 12.67 Ω/square, a resistivity of 2.54 × 10-4 Ω cm, and an optical transmittance of 86.78%, all of which were comparable to a conventional ITO anode. In addition, the MoO3 graded ITO electrode showed a greater work function of 4.92 eV than that (4.6 eV) of an ITO anode, which is beneficial for hole extraction from an organic active layer. Due to the high work function of MoO3 graded ITO electrodes, the acidic PEDOT:PSS-free OSCs fabricated on the MoO3 graded ITO electrode exhibited a power conversion efficiency 3.60% greater than that of a PEDOT:PSS-free OSC on the conventional ITO anode. The successful operation of PEDOT:PSS-free OSCs indicates simpler fabrication steps for cost-effective OSCs and elimination of interfacial reactions caused by the acidic PEDOT:PSS layer for reliable OSCs.

  19. Highly sensitive and selective detection of Al(III) ions in aqueous buffered solution with fluorescent peptide-based sensor.

    PubMed

    In, Byunggyu; Hwang, Gi Won; Lee, Keun-Hyeung

    2016-09-15

    A fluorescent sensor based on a tripeptide (SerGluGlu) with a dansyl fluorophore detected selectively Al(III) among 16 metal ions in aqueous buffered solutions without any organic cosolvent. The peptide-based sensor showed a highly sensitive turn on response to aluminium ion with high binding affinity (1.84×10(4)M(-1)) in aqueous buffered solutions. The detection limit (230nM, 5.98ppb) of the peptide-based sensor was much lower than the maximum allowable level (7.41μM) of aluminium ions in drinking water demanded by EPA. The binding mode of the peptide sensor with aluminium ions was characterized using ESI mass spectrometry, NMR titration, and pH titration experiments. PMID:27503680

  20. Reference electrode for strong oxidizing acid solutions

    DOEpatents

    Rigdon, Lester P.; Harrar, Jackson E.; Bullock, Sr., Jack C.; McGuire, Raymond R.

    1990-01-01

    A reference electrode for the measurement of the oxidation-reduction potentials of solutions is especially suitable for oxidizing solutions such as highly concentrated and fuming nitric acids, the solutions of nitrogen oxides, N.sub.2 O.sub.4 and N.sub.2 O.sub.5, in nitric acids. The reference electrode is fabricated of entirely inert materials, has a half cell of Pt/Ce(IV)/Ce(III)/70 wt. % HNO.sub.3, and includes a double-junction design with an intermediate solution of 70 wt. % HNO.sub.3. The liquid junctions are made from Corning No. 7930 glass for low resistance and negligible solution leakage.

  1. Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

    NASA Astrophysics Data System (ADS)

    Wang, Lan; Lin, Xianzhong; Ennaoui, Ahmed; Wolf, Christian; Lux-Steiner, Martha Ch.; Klenk, Reiner

    2016-02-01

    We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating and inkjet printing. Active area efficiencies of 12.8% and 12.2% have been achieved for In2S3-buffered solar cells respectively, matching the performance of CdS-buffered cells prepared with the same batch of absorbers.

  2. Responses of soil buffering capacity to acid treatment in three typical subtropical forests.

    PubMed

    Jiang, Jun; Wang, Ying-Ping; Yu, Mengxiao; Li, Kun; Shao, Yijing; Yan, Junhua

    2016-09-01

    Elevated anthropogenic acid deposition can significantly affect forest ecosystem functioning by changing soil pH, nutrient balance, and chemical leaching and so on. These effects generally differ among different forests, and the dominant mechanisms for those observed responses often vary, depending on climate, soil conditions and vegetation types. Using soil monoliths (0-40cm) from pine forest (pioneer), coniferous and broadleaved mixed forest (transitional) and broadleaved forest (mature) in southern China, we conducted a leaching experiment with acid treatments at different pH levels (control: pH≈4.5; pH=3.5; pH=2.5). We found that pH3.5 treatment significantly reduced dissolved organic carbon (DOC) concentrations in leachate from the pioneer forest soil. pH2.5 treatment significantly increased concentrations of NO3(-), SO4(2-), Ca(2+), Mg(2+), Al(3+), Fe(3+) and DOC in leachate from the pioneer forest soil, and also concentrations of NO3(-), SO4(2-), Mg(2+), Al(3+), Fe(3+) and DOC in leachate from the transitional forest soil. All acid treatments had no significant effects on concentrations of these chemicals in leachate from the mature forest soil. The responses can be explained by the changes in soil pH, acid neutralizing capacity (ANC) and concentrations of Al and Fe. Our results showed that acid buffering capacity of the pioneer or transitional forest soil was lower than that of the mature forest soil. Therefore preserving mature forests in southern China is important for reducing the adverse impacts of high acid deposition on stream water quality at present and into the future. PMID:27185346

  3. Pharmacokinetic study of a new oral buffered acetylsalicylic acid (ASA) formulation in comparison with plain ASA in healthy volunteers.

    PubMed

    Viganò, G; Garagiola, U; Gaspari, F

    1991-01-01

    A single-blind, randomized, crossover pharmacokinetic study was carried out to investigate the bioavailability of a new oral buffered 325 mg acetylsalicylic acid (ASA) formulation (ASPIRINA 03) in comparison with a 325 mg plain tablet. Twelve healthy volunteers of both sexes, aged between 20 and 37 years, received buffered or plain ASA on two separate occasions with a wash-out interval of at least two weeks. ASA and salicylic acid (SA) plasma levels were determined by a chromatographic method. The results showed no difference between the area under concentration time curve (AUC0-infinity) ASA values of both formulations (p = 0.19), and buffered ASA relative bioavailability was 102.49% (= bioequivalence). A significant difference was found between the AUC0-30 min ASA values: 90.5 micrograms. min/ml with buffered and 67.7 micrograms. min/ml with the plain tablet (p less than 0.05). The buffered ASA time of maximum concentration was shorter (28 +/- 8 min) than the plain one (38 +/- 19 min, p less than 0.05). The plasma concentrations and pharmacokinetic parameters of SA were not significantly different after the administration of the two ASA formulations. The plain ASA tablet had a significantly lower (p less than 0.05) dissolution rate than buffered ASA tablet. Moreover, the buffered ASA tablet significantly (p less than 0.01) increased the pH by 0.5 units. In conclusion, the bioavailability of the new oral buffered ASA was equivalent to that of plain ASA, but the plasma concentration peak was reached in a shorter time. PMID:1809699

  4. Aspirin absorption rates and platelet inhibition times with 325-mg buffered aspirin tablets (chewed or swallowed intact) and with buffered aspirin solution.

    PubMed

    Feldman, M; Cryer, B

    1999-08-15

    Large clinical trials such as the second International Study of Infarct Survival routinely gave patients with myocardial infarction a chewed aspirin, yet there are no data to show whether chewing of aspirin is better, or worse, than swallowing a whole tablet. We performed a randomized, placebo-controlled study to determine whether chewing aspirin or administering it in solution accelerates its absorption and antiplatelet activity. On separate days, 12 fasting volunteers ingested 325 mg of buffered aspirin, either by chewing a tablet for 30 seconds before swallowing it with 4 ounces of water, swallowing a whole tablet with 4 ounces of water, or drinking 4 ounces of Alka Seltzer. Frequent blood samples were obtained for serum aspirin, salicylate, and thromboxane B2 (TxB2) concentrations. With all formulations of aspirin, serum TxB2 decreased 50% when the plasma aspirin concentration reached approximately 1,000 ng/ml. A 50% and 90% decrease in serum TxB2 occurred more quickly after chewing a tablet than after a tablet was swallowed whole. For example, the t 50% for serum TxB2 inhibition was 5.0 +/- 0.6 minutes with the chewed tablet versus 12.0 +/- 2.3 minutes when the tablet was swallowed (p = 0.01). A 50% decrease in serum TxB2 occurred 7.6 +/- 1.2 minutes after Alka Seltzer solution (p = 0.04 vs chewing a tablet; p = 0.13 vs swallowing a whole tablet). Chewing an aspirin tablet is the most effective way of accelerating absorption of aspirin into the blood and shortening the time required for an antiplatelet effect. PMID:10468077

  5. CONDUCTIVITY TITRATION OF GELATIN SOLUTIONS WITH ACIDS.

    PubMed

    Hitchcock, D I

    1923-11-20

    Titrations have been made, by the conductivity method, of gelatin solutions with hydrochloric and sulphuric acids. The results indicate an end-point at about 8.6 cc. of N/10 acid per gm. of gelatin, or a combining weight of about 1,160. These results are in fair agreement with those previously obtained by the hydrogen electrode method. Better agreement between the two methods was found in the case of deaminized gelatin. The data are in accord with a purely chemical conception of the combination between protein and acid.

  6. Proposing buffer zones and simple technical solutions for safeguarding river water quality and public health

    NASA Astrophysics Data System (ADS)

    Podimata, M. V.; Bekri, E. S.; Yannopoulos, P. C.

    2012-04-01

    Alfeios River Basin (ARB) constitutes one of the major hydrologic basins (≈3650km2) of Peloponnisos peninsula in Southern Greece. It is drained by Alfeios River and its tributaries, such as Lousios, Ladhon, Erymanthos, Kladheos, Selinous etc. The present manuscript takes a closer look at the importance of tributary basins and focuses on Erymanthos sub-basin that covers about 360 km2. Erymanthos River springs from Erymanthos Mountain that reaches altitudes of 2200 m and discharges 10 m3/sec, approximately, during the winter period, presenting a sound decrease from half to about an order of magnitude during summertime. Two factors stand out as reasons to select Erymanthos sub-basin as a case study. First, the sub-basin presents a significant variety of ecosystems and comprises a very important river system, since Erymanthos Tributary satisfies, among other uses, drinking water supply for a great majority of citizens in the region. Second, authors' experience of the study area in Research Program Pythagoras II, funded by the European Social Fund (ESF) and the Operational Program for Educational and Vocational Training II (EPEAEK II) of Greece, offers a basis for better understanding of the real problems in the area. Erymanthos watershed, in fact, faces a lot of pressures, in several levels, provoked by human activities and Erymanthos Tributary is vulnerable to pollution. Recognizing the importance of clean water for healthy people, a developing economy, and a sustainable environment, the challenge of the present paper is elaborating human-induced pressures in the study area, analyzing their effects, estimating pollution factors and proposing integrated solutions/tools and a number of methodologies/initiatives used to overcome the problem of contaminating water supply in a catchment that lacks of wastewater treatment and disposal systems. The preservation of a good ecological status in Erymanthos River is not only a necessity for achieving the goals of EU Water

  7. Effect of acetate and carbonate buffers on the photolysis of riboflavin in aqueous solution: a kinetic study.

    PubMed

    Ahmad, Iqbal; Anwar, Zubair; Iqbal, Kefi; Ali, Syed Abid; Mirza, Tania; Khurshid, Adeela; Khurshid, Aqeela; Arsalan, Adeel

    2014-06-01

    The photolysis of riboflavin (RF) in the presence of acetate buffer (pH 3.8-5.6) and carbonate buffer (pH 9.2-10.8) has been studied using a multicomponent spectrophotometric method for the simultaneous assay of RF and its photoproducts. Acetate and carbonate buffers have been found to catalyze the photolysis reaction of RF. The apparent first-order rate constants for the acetate-catalyzed reaction range from 0.20 to 2.86 × 10(-4) s(-1) and for the carbonate-catalyzed reaction from 3.33 to 15.89 × 10(-4) s(-1). The second-order rate constants for the interaction of RF with the acetate and the carbonate ions range from 2.04 to 4.33 × 10(-4) M(-1) s(-1) and from 3.71 to 11.80 × 10(-4) M(-1) s(-1), respectively. The k-pH profile for the acetate-catalyzed reaction is bell shaped and for the carbonate-catalyzed reaction a steep curve. Both HCO3(-) and CO3(2-) ions are involved in the catalysis of the photolysis reaction in alkaline solution. The rate constants for the HCO3(-) and CO3(2-) ions catalyzed reactions are 0.72 and 1.38 × 10(-3) M(-1) s(-1), respectively, indicating a major role of CO3(2-) ions in the catalysis reaction. The loss of RF fluorescence in acetate buffer suggests an interaction between RF and acetate ions to promote the photolysis reaction. The optimum stability of RF solutions is observed in the pH range 5-6, which is suitable for pharmaceutical preparations.

  8. Electrical conductivity of acidic sulfate solution

    NASA Astrophysics Data System (ADS)

    Majima, Hiroshi; Peters, Ernest; Awakura, Yasuhiro; Park, Sung Kook

    1987-03-01

    The electrical conductivities of the aqueous solution system of H2SO4-MSO4 (involving ZnSO4, MgSO4, Na2SO4, and (NH4)2SO4), reported by Tozawa et al., were examined in terms of a (H2O) and H+ ion concentration. The equations to compute the concentrations of various species in aqueous sulfuric acid solutions containing metal sulfates were derived for a typical example of the H2SO4-ZnSO4-MgSO4-(Na2SO4)-H2O system. It was found that the H+ ion concentrations in concentrated sulfuric acid solutions corresponding to practical zinc electrowinning solutions are very high and remain almost constant with or without the addition of metal sulfates. The addition of metal sulfates to aqueous sulfuric acid solution causes a decrease in electrical conductivity, and this phenomenon is attributed to a decrease in water activity, which reflects a decrease in the amount of free water. The relationship between conductivity and water activity at a constant H+ ion concentration is independent of the kind of sulfates added. On the other hand, any increase in H+ ion concentration results in an increase in electrical conductivity. A novel method for the prediction of electrical conductivity of acidic sulfate solution is proposed that uses the calculated data of water activity and the calculated H+ ion concentration. Also, the authors examined an extension of the Robinson-Bower equation to calculate water activity in quarternary solutions based on molarity instead of molality, and found that such calculated values are in satisfactory agreement with those determined experimentally by a transpiration method.

  9. Buffer-free production of gamma-aminobutyric acid using an engineered glutamate decarboxylase from Escherichia coli.

    PubMed

    Kang, Taek Jin; Ho, Ngoc Anh Thu; Pack, Seung Pil

    2013-08-15

    Escherichia coli glutamate decarboxylase (GAD) converts glutamate into γ-aminobutyric acid (GABA) through decarboxylation using proton as a co-substrate. Since GAD is active only at acidic conditions even though pH increases as the reaction proceeds, the conventional practice of using this enzyme involved the use of relatively high concentration of buffers, which might complicate the downstream purification steps. Here we show by simulation and experiments that the free acid substrate, glutamic acid, rather than its monosodium salt can act as a substrate and buffer at the same time. This yielded the buffer- and salt-free synthesis of GABA conveniently in a batch mode. Furthermore, we engineered GAD to hyper active ones by extending or reducing the length of the enzyme by just one residue at its C-terminus. Through the buffer-free reaction with engineered GAD, we could synthesize 1M GABA in 3h, which can be translated into a space-time yield of 34.3g/L/h.

  10. Effects of buffered vinegar and sodium dodecyl sulfate plus levulinic acid on Salmonella Typhimurium survival, shelf-life, and sensory characteristics of ground beef patties.

    PubMed

    Stelzleni, Alexander M; Ponrajan, Amudhan; Harrison, Mark A

    2013-09-01

    The inclusion of two sources of buffered vinegar and sodium dodecyl sulfate plus levulinic acid were studied as interventions for Salmonella Typhimurium and for their effect on shelf-life and sensory characteristics of ground beef. For the Salmonella challenge, beef trimmings (80/20) were inoculated then treated with 2% (w/v) liquid buffered vinegar (LVIN), 2.5% (w/w) powdered buffered vinegar (PVIN), a solution containing 1.0% levulinic acid plus 0.1% sodium dodecyl sulfate (SDLA) at 10% (w/v), or had no intervention applied (CNT). The same trim source and production methods were followed during production of patties for shelf-life and sensory testing without inoculation. SDLA patties had the largest reduction (P<0.05; 0.70 log CFU/g) of Salmonella. However, LVIN and PVIN had the least (P<0.05) psychrotrophic growth. SDLA patties had more purge (P<0.05) and lower (P<0.05) subjective color scores. There were not large differences in sensory characteristics, except PVIN exhibited stronger off-flavor (P<0.05).

  11. Base excess or buffer base (strong ion difference) as measure of a non-respiratory acid-base disturbance.

    PubMed

    Siggaard-Andersen, O; Fogh-Andersen, N

    1995-01-01

    Stewart in 1983 (Can J Physiol Pharmacol 1983: 61: 1444) reintroduced plasma buffer base under the name "strong ion difference" (SID). Buffer base was originally introduced by Singer and Hastings in 1948 (Medicine (Baltimore) 1948: 27: 223). Plasma buffer base, which is practically equal to the sum of bicarbonate and albuminate anions, may be increased due to an excess of base or due to an increased albumin concentration. Singer and Hastings did not consider changes in albumin as acid-base disorders and therefore used the base excess, i.e., the actual buffer base minus the buffer base at normal pH and pCO2, as measure of a non-respiratory acid-base disturbance. Stewart and followers, however, consider changes in albumin concentration to be acid-base disturbances: a patient with normal pH, pCO2, and base excess but with increased plasma buffer base due to increased plasma albumin concentration get the diagnoses metabolic (strong ion) alkalosis (because plasma buffer base is increased) combined with metabolic hyperalbuminaemic acidosis. Extrapolating to whole blood, anaemia and polycytaemia should represent types of metabolic alkalosis and acidosis, respectively. This reveals that the Stewart approach is absurd and anachronistic in the sense that an increase or decrease in any anion is interpreted as indicating an excess or deficit of a specific acid. In other words, a return to the archaic definitions of acids and bases as being the same as anions and cations. We conclude that the acid-base status (the hydrogen ion status) of blood and extracellular fluid is described in terms of the arterial pH, the arterial pCO2, and the extracellular base excess. It is measured with a modern pH-blood gas analyser. The electrolyte status of the plasma is a description of the most important electrolytes, usually measured in venous blood with a dedicated electrolyte analyser, i.e., Na+, Cl-, HCO3-, and K+. Albumin anions contribute significantly to the anions, but calculation

  12. Size Control of (99m)Tc-tin Colloid Using PVP and Buffer Solution for Sentinel Lymph Node Detection.

    PubMed

    Kim, Eun-Mi; Lim, Seok Tae; Sohn, Myung-Hee; Jeong, Hwan-Jeong

    2015-06-01

    Colloidal particle size is an important characteristic that allows mapping sentinel nodes in lymphoscintigraphy. This investigation aimed to introduce different ways of making a (99m)Tc-tin colloid with a size of tens of nanometers. All agents, tin fluoride, sodium fluoride, poloxamer-188, and polyvinylpyrrolidone (PVP), were mixed and labeled with (99m)Tc. Either phosphate or sodium bicarbonate buffers were used to adjust the pH levels. When the buffers were added, the size of the colloids increased. However, as the PVP continued to increase, the size of the colloids was controlled to within tens of nanometers. In all samples, phosphate buffer added PVP (30 mg) stabilized tin colloid ((99m)Tc-PPTC-30) and sodium bicarbonate solution added PVP (50 mg) stabilized tin colloid ((99m)Tc-BPTC-50) were chosen for in vitro and in vivo studies. (99m)Tc-BPTC-50 (<20 nm) was primarily located in bone marrow and was then secreted through the kidneys, and (99m)Tc-PPTC-30 (>100 nm) mainly accumulated in the liver. When a rabbit was given a toe injection, the node uptake of (99m)Tc-PPTC-30 decreased over time, while (99m)Tc-BPTC-50 increased. Therefore, (99m)Tc-BPTC-50 could be a good candidate radiopharmaceutical for sentinel node detection. The significance of this study is that nano-sized tin colloid can be made very easily and quickly by PVP.

  13. Determination of the stability of laser deposited apatite coatings in phosphate buffered saline solution using Fourier transform infrared (FTIR) spectroscopy

    NASA Astrophysics Data System (ADS)

    Antonov, E. N.; Bagratashvili, V. N.; Popov, V. K.; Sobol, E. N.; Howdle, S. M.

    1996-01-01

    We report the use of grazing angle Fourier transform infrared spectroscopy for determination of the stability to erosion of hydroxyapatite coatings. A series of coatings were deposited by pulsed laser ablation onto titanium foils. The coatings were exposed to a phosphate buffered saline solution, and FTIR spectroscopy was used to monitor the depletion of infrared bands associated with phosphate moieties in the hydroxyapatite coatings. The technique allows determintion of the effects of the laser deposition parameters upon the stability to erosion of the coatings.

  14. Antigen retrieval using pH 3.5 glycine-HCl buffer or urea solution for immunohistochemical localization of Ki-67.

    PubMed

    Shi, S R; Chaiwun, B; Young, L; Imam, A; Cote, R J; Taylor, C R

    1994-07-01

    A new antibody (MIB-1) has been described, permitting the demonstration of Ki-67 proliferation antigen in paraffin sections. However, satisfactory results were obtained only after subjecting tissue sections to microwave based antigen retrieval in citrate buffer solution. Other buffer solutions produce equivalent or better results and also permit use of the original Ki-67 antibody, which hitherto has been considered ineffective for paraffin sections.

  15. Speciation in aqueous solutions of nitric acid.

    PubMed

    Hlushak, S; Simonin, J P; De Sio, S; Bernard, O; Ruas, A; Pochon, P; Jan, S; Moisy, P

    2013-02-28

    In this study, speciation in aqueous solutions of nitric acid at 25 °C was assessed in two independent ways. First, Raman experiments were carried out and interpreted in terms of free nitrate ions, ion pairs and neutral HNO(3) molecules. In parallel, a model was developed to account for the formation of these two kinds of pairs. It was based on an extension of the binding mean spherical approximation (BiMSA), or associative MSA (AMSA), in which the size and the charge of the ions in the chemical pair may differ from those of the free ions. A simultaneous fit of the osmotic coefficient and of the proportion of free ions (obtained from Raman spectroscopy experiments) led to an estimation of the speciation in nitric acid solutions. The result obtained using this procedure was compared with the estimation obtained from the Raman experiments.

  16. Alkaline earth cation extraction from acid solution

    DOEpatents

    Dietz, Mark; Horwitz, E. Philip

    2003-01-01

    An extractant medium for extracting alkaline earth cations from an aqueous acidic sample solution is described as are a method and apparatus for using the same. The separation medium is free of diluent, free-flowing and particulate, and comprises a Crown ether that is a 4,4'(5')[C.sub.4 -C.sub.8 -alkylcyclohexano]18-Crown-6 dispersed on an inert substrate material.

  17. Halogenated earth abundant metalloporphyrins as photostable sensitizers for visible-light-driven water oxidation in a neutral phosphate buffer solution.

    PubMed

    Chen, Hung-Cheng; Reek, Joost N H; Williams, René M; Brouwer, Albert M

    2016-06-01

    Very photostable tetrachloro-metalloporphyrins were developed as sensitizers for visible-light-driven water oxidation coupled to cobalt based water-oxidation catalysts in concentrated (0.1 M) phosphate buffer solution. Potassium persulfate (K2S2O8) acts as a sacrificial electron acceptor to oxidize the metalloporphyrin photosensitizers in their excited states. The radical cations thus produced drive the cobalt based water-oxidation catalysts: Co4O4-cubane and Co(NO3)2 as pre-catalyst for cobalt-oxide (CoOx) nanoparticles. Two different metalloporphyrins (Cu(ii) and Ni(ii)) both showed very high photostability in the photocatalytic reaction, as compared to non-halogenated analogues. This indicates that photostability primarily depends on the substitution of the porphyrin macrocycle, not on the central metal. Furthermore, our molecular design strategy not only positively increases the electrochemical potential by 120-140 mV but also extends the absorption spectrum up to ∼600 nm. As a result, the solar photon capturing abilities of halogenated metalloporphyrins (Cu(ii) and Ni(ii)) are comparable to that of the natural photosynthetic pigment, chlorophyll a. We successfully demonstrate long-term (>3 h) visible-light-driven water oxidation using our molecular system based on earth-abundant (first-row transition) metals in concentrated phosphate buffer solution.

  18. Halogenated earth abundant metalloporphyrins as photostable sensitizers for visible-light-driven water oxidation in a neutral phosphate buffer solution.

    PubMed

    Chen, Hung-Cheng; Reek, Joost N H; Williams, René M; Brouwer, Albert M

    2016-06-01

    Very photostable tetrachloro-metalloporphyrins were developed as sensitizers for visible-light-driven water oxidation coupled to cobalt based water-oxidation catalysts in concentrated (0.1 M) phosphate buffer solution. Potassium persulfate (K2S2O8) acts as a sacrificial electron acceptor to oxidize the metalloporphyrin photosensitizers in their excited states. The radical cations thus produced drive the cobalt based water-oxidation catalysts: Co4O4-cubane and Co(NO3)2 as pre-catalyst for cobalt-oxide (CoOx) nanoparticles. Two different metalloporphyrins (Cu(ii) and Ni(ii)) both showed very high photostability in the photocatalytic reaction, as compared to non-halogenated analogues. This indicates that photostability primarily depends on the substitution of the porphyrin macrocycle, not on the central metal. Furthermore, our molecular design strategy not only positively increases the electrochemical potential by 120-140 mV but also extends the absorption spectrum up to ∼600 nm. As a result, the solar photon capturing abilities of halogenated metalloporphyrins (Cu(ii) and Ni(ii)) are comparable to that of the natural photosynthetic pigment, chlorophyll a. We successfully demonstrate long-term (>3 h) visible-light-driven water oxidation using our molecular system based on earth-abundant (first-row transition) metals in concentrated phosphate buffer solution. PMID:27197873

  19. All solution processable organic photovoltaic cells using DMDCNQI as an organic N-type buffer layer.

    PubMed

    Yang, Eui Yeol; So, Byoung Min; Chung, Chan Moon; Oh, Se Young

    2012-01-01

    Organic photovoltaic cells consisting of ITO/PEDOT-PSS/P3HT:PCBM/TiO(x)/DMDCNQI/Al have been fabricated by using dip-coated DMDCNQI layer as a cathode buffer material. We have investigated the physical effects of charge transfer complex and wettability of DMDCNQI between TiO(x)/P3HT:PCBM layer and Al cathode electrode on the performance of organic photovoltaic cell. The photovoltaic cell fabricated with a dip-coated DMDCNQI layer exhibited almost similar performance compared to the device using conventional evaporated DMDCNQI layer. Especially, the power conversion efficiency of the prepared organic photovoltaic cell using TiO(x)/DMDCNQI layer was improved to 3.1%, which is mainly due to the decrease in the low contact resistance of organic-metal interface.

  20. Photoelectrochemical study of pitting on iron in borate buffer solution containing inhibitor

    SciTech Connect

    Yang, M.; Chen, L.; Cai, S.

    1997-01-01

    The photoelectrochemical behavior and the susceptibility of iron to pitting in borate buffer containing chloride ions (Cl{sup {minus}}) were investigated in the presence and absence of inhibitor PC-604, which is a mixture of polyhydric alcohol phosphoric easter and polyphosphoric ester of various molecular weights. Measurements of the band gap (E{sub g}) of the passive film on iron showed inhibitor concentration and passivation time did not interfere with E{sub g}. Photocurrent and photocurrent transients increased with increasing inhibitor quantities and passivation times at constant potential. The decay time-constant of the photocurrent transient was investigated as a specific parameter of the film. Data showed this parameter was related to pitting susceptibility of the passive film on iron.

  1. Wet oxidation of salicylic acid solutions.

    PubMed

    Collado, Sergio; Garrido, Laura; Laca, Adriana; Diaz, Mario

    2010-11-15

    Salicylic acid is a frequent pollutant in several industrial wastewaters. Uncatalyzed wet air oxidation, which is a promising technique for the treatment of phenolic effluents, has not been analyzed yet for the removal of salicylic acid. The effect of different conditions of pH (1.3-12.3), pressure (1.0-4.1 MPa), temperature (413-443 K), and initial concentrations (1.45-14.50 mM) on the wet oxidation of salicylate/salicylic acid solutions have here been investigated. The pH value of the reaction media was found to be a key parameter for the rate of the oxidation process with an optimum at pH 3.1, when the concentrations of salicylic acid and salicylate were similar. The oxidation reaction followed pseudofirst-order kinetics with respect to salicylic acid and 0.82 order with respect to dissolved oxygen. Additionally, the evolution of the color during the wet oxidation was analyzed and discussed in relation with the formation of intermediate compounds. Then, a reaction pathway for the noncatalytic wet oxidation of the salicylic acid was proposed.

  2. Pictorial Analogies XI: Concentrations and Acidity of Solutions.

    ERIC Educational Resources Information Center

    Fortman, John J.

    1994-01-01

    Presents pictorial analogies of several concepts relating to solutions for chemistry students. These include concentration of solution, strength of solution, supersaturated solution, and conjugate acid-base pairs. Among the examples are comparison of acid strength to percentage of strong soldiers or making supersaturated solution analogous to a…

  3. Acidities of Water and Methanol in Aqueous Solution and DMSO

    ERIC Educational Resources Information Center

    Gao, Daqing

    2009-01-01

    The relative acidities of water and methanol have been a nagging issue. In gas phase, methanol is more acidic than water by 36.0 kJ/mol; however, in aqueous solution, the acidities of methanol and water are almost identical. The acidity of an acid in solution is determined by both the intrinsic gas-phase ionization Gibbs energy and the solvent…

  4. In Vivo Predictive Dissolution: Comparing the Effect of Bicarbonate and Phosphate Buffer on the Dissolution of Weak Acids and Weak Bases.

    PubMed

    Krieg, Brian J; Taghavi, Seyed Mohammad; Amidon, Gordon L; Amidon, Gregory E

    2015-09-01

    Bicarbonate is the main buffer in the small intestine and it is well known that buffer properties such as pKa can affect the dissolution rate of ionizable drugs. However, bicarbonate buffer is complicated to work with experimentally. Finding a suitable substitute for bicarbonate buffer may provide a way to perform more physiologically relevant dissolution tests. The dissolution of weak acid and weak base drugs was conducted in bicarbonate and phosphate buffer using rotating disk dissolution methodology. Experimental results were compared with the predicted results using the film model approach of (Mooney K, Mintun M, Himmelstein K, Stella V. 1981. J Pharm Sci 70(1):22-32) based on equilibrium assumptions as well as a model accounting for the slow hydration reaction, CO2 + H2 O → H2 CO3 . Assuming carbonic acid is irreversible in the dehydration direction: CO2 + H2 O ← H2 CO3 , the transport analysis can accurately predict rotating disk dissolution of weak acid and weak base drugs in bicarbonate buffer. The predictions show that matching the dissolution of weak acid and weak base drugs in phosphate and bicarbonate buffer is possible. The phosphate buffer concentration necessary to match physiologically relevant bicarbonate buffer [e.g., 10.5 mM (HCO3 (-) ), pH = 6.5] is typically in the range of 1-25 mM and is very dependent upon drug solubility and pKa . PMID:25980464

  5. In Vivo Predictive Dissolution: Comparing the Effect of Bicarbonate and Phosphate Buffer on the Dissolution of Weak Acids and Weak Bases.

    PubMed

    Krieg, Brian J; Taghavi, Seyed Mohammad; Amidon, Gordon L; Amidon, Gregory E

    2015-09-01

    Bicarbonate is the main buffer in the small intestine and it is well known that buffer properties such as pKa can affect the dissolution rate of ionizable drugs. However, bicarbonate buffer is complicated to work with experimentally. Finding a suitable substitute for bicarbonate buffer may provide a way to perform more physiologically relevant dissolution tests. The dissolution of weak acid and weak base drugs was conducted in bicarbonate and phosphate buffer using rotating disk dissolution methodology. Experimental results were compared with the predicted results using the film model approach of (Mooney K, Mintun M, Himmelstein K, Stella V. 1981. J Pharm Sci 70(1):22-32) based on equilibrium assumptions as well as a model accounting for the slow hydration reaction, CO2 + H2 O → H2 CO3 . Assuming carbonic acid is irreversible in the dehydration direction: CO2 + H2 O ← H2 CO3 , the transport analysis can accurately predict rotating disk dissolution of weak acid and weak base drugs in bicarbonate buffer. The predictions show that matching the dissolution of weak acid and weak base drugs in phosphate and bicarbonate buffer is possible. The phosphate buffer concentration necessary to match physiologically relevant bicarbonate buffer [e.g., 10.5 mM (HCO3 (-) ), pH = 6.5] is typically in the range of 1-25 mM and is very dependent upon drug solubility and pKa .

  6. Ultrafiltration of highly concentrated antibody solutions: Experiments and modeling for the effects of module and buffer conditions.

    PubMed

    Binabaji, Elaheh; Ma, Junfen; Rao, Suma; Zydney, Andrew L

    2016-05-01

    Although ultrafiltration is currently used for the concentration and formulation of nearly all biotherapeutics, obtaining the very high target concentrations for monoclonal antibody products is challenging. The objective of this work was to examine the effects of the membrane module design and buffer conditions on both the filtrate flux and maximum achievable protein concentration during the ultrafiltration of highly concentrated monoclonal antibody solutions. Experimental data were obtained using both hollow fiber and screened cassettes and in the presence of specific excipients that are known to alter the solution viscosity. Data were compared with predictions of a recently developed model that accounts for the complex thermodynamic and hydrodynamic behavior in these systems, including the effects of back-filtration arising from the large pressure drop through the module due to the high viscosity of the concentrated antibody solutions. Model calculations were in good agreement with experimental data in hollow fiber modules with very different fiber length and in screened cassettes having different screen geometries. These results provide important insights into the key factors controlling the filtrate flux and maximum achievable protein concentration during ultrafiltration of highly concentrated antibody solutions as well as a framework for the development of enhanced ultrafiltration processes for this application. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:692-701, 2016.

  7. Reactive solute transport in acidic streams

    USGS Publications Warehouse

    Broshears, R.E.

    1996-01-01

    Spatial and temporal profiles of Ph and concentrations of toxic metals in streams affected by acid mine drainage are the result of the interplay of physical and biogeochemical processes. This paper describes a reactive solute transport model that provides a physically and thermodynamically quantitative interpretation of these profiles. The model combines a transport module that includes advection-dispersion and transient storage with a geochemical speciation module based on MINTEQA2. Input to the model includes stream hydrologic properties derived from tracer-dilution experiments, headwater and lateral inflow concentrations analyzed in field samples, and a thermodynamic database. Simulations reproduced the general features of steady-state patterns of observed pH and concentrations of aluminum and sulfate in St. Kevin Gulch, an acid mine drainage stream near Leadville, Colorado. These patterns were altered temporarily by injection of sodium carbonate into the stream. A transient simulation reproduced the observed effects of the base injection.

  8. Electrochemical Behavior of Pure Copper in Phosphate Buffer Solutions: A Comparison Between Micro- and Nano-Grained Copper

    NASA Astrophysics Data System (ADS)

    Imantalab, O.; Fattah-alhosseini, A.; Keshavarz, M. K.; Mazaheri, Y.

    2016-02-01

    In this work, electrochemical behavior of annealed (micro-) and nano-grained pure copper (fabricated by accumulative roll bonding process) in phosphate buffer solutions of various pH values ranging from 10.69 to 12.59 has been studied. Before any electrochemical measurements, evaluation of microstructure was obtained by optical microscope and transmission electron microscopy. To investigate the electrochemical behavior of the samples, the potentiodynamic polarization, Mott-Schottky analysis, and electrochemical impedance spectroscopy (EIS) were carried out. Potentiodynamic polarization plots and EIS measurements revealed that as a result of grain refinement, the passive behavior of the nano-grained sample was improved compared to that of annealed pure copper. Also, Mott-Schottky analysis indicated that the passive films behaved as p-type semiconductors and grain refinement did not change the semiconductor type of passive films.

  9. Effect of Phosphate-Buffered Solution Corrosion on the Ratcheting Fatigue Behavior of a Duplex Mg-Li-Al Alloy

    NASA Astrophysics Data System (ADS)

    Yuan, Xin; Yu, Dunji; Gao, Li-Lan; Gao, Hong

    2016-05-01

    This work reports the uniaxial ratcheting and fatigue behavior of a duplex Mg-Li-Al alloy under the influence of phosphate-buffered solution corrosion. Microstructural observations reveal pitting and filament corrosion defects, which impair the load-bearing capacity of the alloy and cause stress concentration, thus leading to an accelerated accumulation of ratcheting strain and shortened fatigue life under the same nominal loading conditions. Comparing Smith model, Smith-Watson-Topper model, and Paul-Sivaprasad-Dhar model, a ratcheting fatigue life prediction model based on the Broberg damage rule and the Paul-Sivaprasad-Dhar model was proposed, and the model yielded a superior prediction for the studied magnesium alloy.

  10. Process for the extraction of strontium from acidic solutions

    DOEpatents

    Horwitz, E. Philip; Dietz, Mark L.

    1994-01-01

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid.

  11. Process for the extraction of strontium from acidic solutions

    DOEpatents

    Horwitz, E.P.; Dietz, M.L.

    1993-01-01

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid.

  12. Process for the extraction of strontium from acidic solutions

    DOEpatents

    Horwitz, E.P.; Dietz, M.L.

    1994-09-06

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid. 4 figs.

  13. Prevention of postoperative pericardial adhesions with a hyaluronic acid coating solution. Experimental safety and efficacy studies.

    PubMed

    Mitchell, J D; Lee, R; Hodakowski, G T; Neya, K; Harringer, W; Valeri, C R; Vlahakes, G J

    1994-06-01

    Postoperative pericardial adhesions complicate reoperative cardiac procedures. Topical application of solutions containing hyaluronic acid have been shown to reduce adhesions after abdominal and orthopedic surgery. The mechanism by which hyaluronic acid solutions prevent adhesion formation is unknown but may be due to a cytoprotective effect on mesothelial surfaces, which would limit intraoperative injury. In this study, we tested the efficacy and safety of hyaluronic acid coating solutions for the prevention of postoperative intrapericardial adhesion formation. Eighteen mongrel dogs underwent median sternotomy and pericardiotomy followed by a standardized 2-hour protocol of forced warm air desiccation and abrasion of the pericardial and epicardial surfaces. Group 1 (n = 6) served as untreated control animals. Group 2 (n = 6) received topical administration of 0.4% hyaluronic acid in phosphate-buffered saline solution at the time of pericardiotomy, at 20-minute intervals during the desiccation/abrasion protocol, and at pericardial closure. The total test dose was less than 1% of the circulating blood volume. Group 3 (n = 6) served as a vehicle control, receiving phosphate-buffered saline solution as a topical agent in a fashion identical to that used in group 2. At resternotomy 8 weeks after the initial operation, the intrapericardial adhesions were graded on a 0 to 4 severity scale at seven different areas covering the ventricular, atrial, and great vessel surfaces. In both the untreated control (group 1, mean score 3.2 +/- 0.4) and vehicle control (group 3, mean score 3.3 +/- 0.2) animals, dense adhesions were encountered. In contrast, animals treated with the hyaluronic acid solution (group 2, mean score 0.8 +/- 0.3) characteristically had no adhesions or filmy, transparent adhesions graded significantly less severe than either the untreated control (group 2 versus group 1, p < 0.001) or vehicle control (group 2 versus group 3, p < 0.001) animals. In separate

  14. A simple ratiometric and colorimetric chemosensor for the selective detection of fluoride in DMSO buffered solution

    NASA Astrophysics Data System (ADS)

    Niu, Hu; Shu, Qinghai; Jin, Shaohua; Li, Bingjun; Zhu, Jiaping; Li, Lijie; Chen, Shusen

    2016-01-01

    A derivative of squaramide (cyclobuta[b]quinoxaline-1, 2(3H, 8H)-dione) has been synthesized for the ratiometric and colorimetric sensing of F- in aqueous solution in competitive fashion. With F-, probe 1 showed a highly selective naked-eye detectable color change along with a characteristic UV-Vis absorbance over other tested ions, which probably originates from the deprotonation occurred between 1 and F-, as proved by the 1H NMR titration experiments and DFT calculations.

  15. Solute-solvent interactions in micellar electrokinetic chromatography. Selectivity of lithium dodecyl sulfate-lithium perfluorooctanesulfonate mixed-micellar buffers.

    PubMed

    Fuguet, E; Ràfols, C; Bosch, E; Rosés, M; Abraham, M H

    2001-01-12

    The solvation parameter model has been applied to the characterization of micellar electrokinetic chromatographic (MEKC) systems with mixtures of lithium dodecyl sulfate and lithium perfluorooctanesulfonate as surfactant. The variation in MEKC surfactant composition results in changes in the coefficients of the correlation equation, which in turns leads to information on solute-solvent and solute-micelle interactions. Lithium perfluorooctanesulfonate is more dipolar and hydrogen bond acidic but less polarizable and hydrogen bond basic than lithium dodecyl sulfate. Therefore mixtures of lithium dodecyl sulfate and lithium perfluorooctanesulfonate cover a very wide range of polarity and hydrogen bond properties, which in turn results in important selectivity changes for analytes with different solute properties.

  16. Thermal transformation of trans-5-O-caffeoylquinic acid (trans-5-CQA) in alcoholic solutions.

    PubMed

    Dawidowicz, Andrzej L; Typek, Rafal

    2015-01-15

    Chlorogenic acid (CQA), the ester of caffeic acid with quinic acid supplied to human organisms mainly with coffee, tea, fruit and vegetables, has been one of the most studied polyphenols. It is potentially useful in pharmaceuticals, food additives, and cosmetics due to its recently discovered biomedical activity, which revived interest in its properties, isomers and natural occurrence. We found that the heating of the alcoholic solution of trans-5-O-caffeoylquinic acid produced at least twenty compounds (chlorogenic acid derivatives and its reaction products with water and alcohol). The formation of three of them (methoxy, ethoxy and propoxy adducts) has not been reported yet. No reports exist either on methoxy adducts of 3- and 4-O-caffeoylquinic acid appearing in buffered methanol/water mixtures at pH exceeding 7. We observed that the amount of each formed component depended on the heating time, type of alcohol, its concentration in alcoholic/water mixture, and pH.

  17. Implementing bacterial acid resistance into cell-free protein synthesis for buffer-free expression and screening of enzymes.

    PubMed

    Kim, Ho-Cheol; Kim, Kwang-Soo; Kang, Taek-Jin; Choi, Jong Hyun; Song, Jae Jun; Choi, Yun Hee; Kim, Byung-Gee; Kim, Dong-Myung

    2015-12-01

    Cell-free protein synthesis utilizes translational machinery isolated from the cells for in vitro expression of template genes. Because it produces proteins without gene cloning and cell cultivation steps, cell-free protein synthesis can be used as a versatile platform for high-throughput expression of enzyme libraries. Furthermore, the open nature of cell-free protein synthesis allows direct integration of enzyme synthesis with subsequent screening steps. However, the presence of high concentration of chemical buffers in the conventional reaction mixture makes it difficult to streamline cell-free protein synthesis with pH-based assay of the synthesized enzymes. In this study, we have implemented an enzyme-assisted bacterial acid resistance mechanism into an Escherichia coli (E.coli) extract-based cell-free protein synthesis system in place of chemical buffers. When deployed in the reaction mixture for cell-free synthesis of enzymes, through proton-consuming conversion of glutamate into γ-aminobutyric acid (GABA), an engineered glutamate decarboxylase (GADβ) was able to maintain the pH of reaction mixture during enzyme synthesis. Because the reaction mixture becomes free of buffering capacity upon the depletion of glutamate, synthesized enzyme could be directly assayed without purification steps. The designed method was successfully applied to the screening of mutant library of sialyltransferase genes to identify mutants with improved enzymatic activity.

  18. Stacking and determination of phenazine-1-carboxylic acid with low pKa in soil via moving reaction boundary formed by alkaline and double acidic buffers in capillary electrophoresis.

    PubMed

    Sun, Chong; Yang, Xiao-Di; Fan, Liu-Yin; Zhang, Wei; Xu, Yu-Quan; Cao, Cheng-Xi

    2011-04-01

    As shown herein, a normal moving reaction boundary (MRB) formed by an alkaline buffer and a single acidic buffer had poor stacking to the new important plant growth promoter of phenazine-1-carboxylic acid (PCA) in soil due to the leak induced by its low pK(a). To stack the PCA with low pK(a) efficiently, a novel stacking system of MRB was developed, which was formed by an alkaline buffer and double acidic buffers (viz., acidic sample and blank buffers). With the novel system, the PCA leaking into the blank buffer from the sample buffer could be well stacked by the prolonged MRB formed between the alkaline buffer and blank buffer. The relevant mechanism of stacking was discussed briefly. The stacking system, coupled with sample pretreatment, could achieve a 214-fold increase of PCA sensitivity under the optimal conditions (15 mM (pH 11.5) Gly-NaOH as the alkaline buffer, 15 mM (pH 3.0) Gly-HCl-acetonitrile (20%, v/v) as the acidic sample buffer, 15 mM (pH 3.0) Gly-HCl as the blank buffer, 3 min 13 mbar injection of double acidic buffers, benzoic acid as the internal standard, 75 μm i.d. × 53 cm (44 cm effective length) capillary, 25 kV and 248 nm). The limit of detection of PCA in soil was decreased to 17 ng/g, the intra-day and inter-day precision values (expressed as relative standard deviations) were 3.17-4.24% and 4.17-4.87%, respectively, and the recoveries of PCA at three concentration levels changed from 52.20% to 102.61%. The developed method could be used for the detection of PCA in soil at trace level.

  19. Selective Conversion of 5-Hydroxymethylfuraldehyde Using Cp*Ir Catalysts in Aqueous Formate Buffer Solution.

    PubMed

    Wu, Wei-Peng; Xu, Yong-Jian; Zhu, Rui; Cui, Min-Shu; Li, Xing-Long; Deng, Jin; Fu, Yao

    2016-05-23

    The highly selective hydrogenation/hydrolytic ring-opening reaction of 5-hydroxymethylfuraldehyde (5-HMF) was catalyzed by homogeneous Cp*Ir(III) half-sandwich complexes to produce 1-hydroxy-2,5-hexanedione (HHD). Adjustment of pH was found to regulate the distribution of products and reaction selectivity, and full conversion of 5-HMF to HHD with 99 % selectivity was achieved at pH 2.5. A mechanistic study revealed that the hydrolysis/ring-opening reaction of 2,5-bis-(hydroxymethyl)furan is the important intermediate reaction step. In addition, an isolated yield of 85 % for HHD was obtained in a 10 g-scale experiment, and the reaction with fructose as the starting material also led to a 98 % GC yield (71.9 % to fructose) of HHD owing to the excellent tolerance of the catalyst under acidic conditions. PMID:27075722

  20. Preparation of bi-axially aligned YBa 2Cu 3O 7- δ film on CeO 2-buffered MgO by chemical solution deposition

    NASA Astrophysics Data System (ADS)

    Yamagiwa, K.; Hiei, H.; Takahashi, Y.; Kim, S. B.; Matsumoto, K.; Ikuta, H.; Mizutani, U.; Hirabayashi, I.

    2000-06-01

    We have succeeded in preparing in-plane aligned YBa 2Cu 3O 7- δ (Y123) film by chemical solution deposition (CSD) processing on CeO 2 (100)-buffered MgO (100) substrates. The CeO 2 buffer film was deposited on MgO (100) single crystalline substrate by pulsed laser deposition (PLD). For CSD coating, a homogeneous coating solution having a molar ratio of Y:Ba:Cu=1:2:3, was prepared by dissolving metal naphthenates in toluene. This solution was spin-coated both on the YSZ (100) and on the CeO 2-buffered MgO (100) single crystalline substrates. The precursor films were calcined at 425°C and fired at various temperatures under low oxygen partial pressure ( pO 2). All Y123 films showed strong (00 n) peaks, which correspond to c-axis orientation perpendicular to the substrates and their a/ b-axes were in-plane aligned. We confirmed that CeO 2 buffer is usable for CSD processing. While the Y123 films on the YSZ reacted with the substrate forming BaZrO 3 phase and did not show sufficient superconducting properties. The Tc,zero value of the Y123 film prepared on CeO 2-buffered MgO substrate was 91.5 K and Jc was 1.2×10 5 A/cm 2 at 77 K, 0 T.

  1. Buffer Standards for the Biological pH of the Amino Acid N-[2 hydroxyethyl]piperazine-N’-[3-propanesulfonic acid], HEPPS, From (278.15 to 328.15) K

    PubMed Central

    Roy, Lakshmi N.; Roy, Rabindra N.; Wollen, Joshua T.; Harmon, Meagan A.; Stegner, Jessica M.; Shah, Ankita A.; Henson, Isaac B.

    2011-01-01

    For the HEPPS buffer under investigation, there are seven buffer solutions without NaCl and eight buffer solutions that contain Cl− and have an ionic strength (I = 0.16 mol·kg−1), which is similar to that of blood plasma. These buffer solutions have been evaluated in the temperature range of (278.15 to 328.15) K using the extended Debye- Hückel equation and the Bates-Guggenheim convention. The previously determined Ej values have been used to determine the operational pH values of HEPPS buffer solutions at (298.15 and 310.15) K. These are recommended as secondary standard reference solutions for pH measurements in saline media with an isotonic ionic strength of I = 0.16 mol·kg−1. PMID:22096257

  2. Buffer Standards for the Biological pH of the Amino Acid N-[2 hydroxyethyl]piperazine-N'-[3-propanesulfonic acid], HEPPS, From (278.15 to 328.15) K.

    PubMed

    Roy, Lakshmi N; Roy, Rabindra N; Wollen, Joshua T; Harmon, Meagan A; Stegner, Jessica M; Shah, Ankita A; Henson, Isaac B

    2011-01-01

    For the HEPPS buffer under investigation, there are seven buffer solutions without NaCl and eight buffer solutions that contain Cl(-) and have an ionic strength (I = 0.16 mol·kg(-1)), which is similar to that of blood plasma. These buffer solutions have been evaluated in the temperature range of (278.15 to 328.15) K using the extended Debye- Hückel equation and the Bates-Guggenheim convention. The previously determined E(j) values have been used to determine the operational pH values of HEPPS buffer solutions at (298.15 and 310.15) K. These are recommended as secondary standard reference solutions for pH measurements in saline media with an isotonic ionic strength of I = 0.16 mol·kg(-1).

  3. Buffers more than buffering agent: introducing a new class of stabilizers for the protein BSA.

    PubMed

    Gupta, Bhupender S; Taha, Mohamed; Lee, Ming-Jer

    2015-01-14

    In this study, we have analyzed the influence of four biological buffers on the thermal stability of bovine serum albumin (BSA) using dynamic light scattering (DLS). The investigated buffers include 4-(2-hydroxyethyl)piperazine-1-ethanesulfonic acid (HEPES), 4-(2-hydroxyethyl)-1-piperazine-propanesulfonic acid (EPPS), 4-(2-hydroxyethyl)piperazine-1-ethanesulfonic acid sodium salt (HEPES-Na), and 4-morpholinepropanesulfonic acid sodium salt (MOPS-Na). These buffers behave as a potential stabilizer for the native structure of BSA against thermal denaturation. The stabilization tendency follows the order of MOPS-Na > HEPES-Na > HEPES ≫ EPPS. To obtain an insight into the role of hydration layers and peptide backbone in the stabilization of BSA by these buffers, we have also explored the phase transition of a thermoresponsive polymer, poly(N-isopropylacrylamide (PNIPAM)), a model compound for protein, in aqueous solutions of HEPES, EPPS, HEPES-Na, and MOPS-Na buffers at different concentrations. It was found that the lower critical solution temperatures (LCST) of PNIPAM in the aqueous buffer solutions substantially decrease with increase in buffer concentration. The mechanism of interactions between these buffers and protein BSA was probed by various techniques, including UV-visible, fluorescence, and FTIR. The results of this series of studies reveal that the interactions are mainly governed by the influence of the buffers on the hydration layers surrounding the protein. We have also explored the possible binding sites of BSA with these buffers using a molecular docking technique. Moreover, the activities of an industrially important enzyme α-chymotrypsin (α-CT) in 0.05 M, 0.5 M, and 1.0 M of HEPES, EPPS, HEPES-Na, and MOPS-Na buffer solutions were analyzed at pH = 8.0 and T = 25 °C. Interestingly, the activities of α-CT were found to be enhanced in the aqueous solutions of these investigated buffers. Based upon the Jones-Dole viscosity parameters, the

  4. Dependence of buffer acidity and surfactant chain-length on electro-osmotic mobility in thermoplastic microchannels.

    PubMed

    Wang, Shau-Chun; Lee, Chia-Yu; Chen, Hsiao-Ping

    2005-04-15

    In this paper, we report the dependence of buffer pH and coating surfactant chain-length on electro-osmotic (EO) mobility in co-polyester microchannels. Thermoplastics co-polyester hydrolyzes to anionic functionality to create electrical double layer on the micro-channel walls. These negatively charged sites are partially or completely screened when long-chain surfactants are added into the buffer. This ancillary technique to modify surface charge polarity to avoid analyte adsorption is known as dynamic coating. We develop a theory to predict the EO mobility tendency on buffer acidity considering the combination of pH-dependent surfactant aggregation and surface dissociation. Our findings of pH-dependent EO mobility in coated channels, using three types of quaternary ammonium surfactants, lauryltrimethyammonium bromide (LTAB), trimethyl (tetradecyl) ammonium bromide (TTAB), and cetyltrimethyammonium bromide (CTAB), agree with our theoretical prediction. We also explain the chain-length dependence of mobility with a collaborative adsorption mechanism of surfactant aggregates.

  5. Effects of injecting calcium-buffer solution on [Ca2+]i in voltage-clamped snail neurons.

    PubMed Central

    Kennedy, H J; Thomas, R C

    1996-01-01

    We have investigated why fura-2 and Ca(2+)-sensitive microelectrodes report different values for the intracellular free calcium ion concentration ([Ca(2+)]i or its negative log, pCa(i)) of snail neurons voltage-clamped to -50 or -60 mV. Both techniques were initially calibrated in vitro, using calcium calibration solutions that had ionic concentrations similar to those of snail neuron cytoplasm. Pressure injections of the same solutions at resting and elevated [Ca(2+)]i were used to calibrate both methods in vivo. In fura-2-loaded cells these pressure injections generated changes in [Ca(2+)]i that agreed well with those expected from the in vitro calibration. Thus, using fura-2 calibrated in vitro, the average resting [Ca(2+)]i was found to be 38 nM (pCa(i) 7.42 +/- 0.05). With Ca(2+)-sensitive microelectrodes, the first injection of calibration solutions always caused a negative shift in the recorded microelectrode potential, as if the injection lowered [Ca2+]i. No such effects were seen on the fura-2 ratio. When calibrated in vivo the Ca(2+)-sensitive microelectrode gave an average resting [Ca2+]i of approximately 25 nM (pCa(i) 7.6 +/- 0.1), much lower than when calibrated in vitro. We conclude that [Ca(2+)]i in snail neurons is approximately 40 nM and that Ca(2+)-sensitive microelectrodes usually cause a leak at the point of insertion. The effects of the leak were minimized by injection of a mobile calcium buffer. PMID:9172736

  6. Adsorption mechanism of acids and bases in reversed-phase liquid chromatography in weak buffered mobile phases designed for liquid chromatography/mass spectrometry.

    PubMed

    Gritti, Fabrice; Guiochon, Georges

    2009-03-01

    The overloaded band profiles of five acido-basic compounds were measured, using weakly buffered mobile phases. Low buffer concentrations were selected to provide a better understanding of the band profiles recorded in LC/MS analyses, which are often carried out at low buffer concentrations. In this work, 10 microL samples of a 50 mM probe solution were injected into C(18)-bonded columns using a series of five buffered mobile phases at (SW)pH between 2 and 12. The retention times and the shapes of the bands were analyzed based on thermodynamic arguments. A new adsorption model that takes into account the simultaneous adsorption of the acidic and the basic species onto the endcapped adsorbent, predicts accurately the complex experimental profiles recorded. The adsorption mechanism of acido-basic compounds onto RPLC phases seems to be consistent with the following microscopic model. No matter whether the acid or the base is the neutral or the basic species, the neutral species adsorbs onto a large number of weak adsorption sites (their saturation capacity is several tens g/L and their equilibrium constant of the order of 0.1 L/g). In contrast, the ionic species adsorbs strongly onto fewer active sites (their saturation capacity is about 1g/L and their equilibrium constant of the order of a few L/g). From a microscopic point of view and in agreement with the adsorption isotherm of the compound measured by frontal analysis (FA) and with the results of Monte-Carlo calculations performed by Schure et al., the first type of adsorption sites are most likely located in between C(18)-bonded chains and the second type of adsorption sites are located deeper in contact with the silica surface. The injected concentration (50 mM) was too low to probe the weakest adsorption sites (saturation capacity of a few hundreds g/L with an equilibrium constant of one hundredth of L/g) that are located at the very interface between the C(18)-bonded layer and the bulk phase. PMID:18976999

  7. Adsorption mechanism of acids and bases in reversed-phase liquid chromatography in weak buffered mobile phases designed for liquid chromatography/mass spectrometry.

    PubMed

    Gritti, Fabrice; Guiochon, Georges

    2009-03-01

    The overloaded band profiles of five acido-basic compounds were measured, using weakly buffered mobile phases. Low buffer concentrations were selected to provide a better understanding of the band profiles recorded in LC/MS analyses, which are often carried out at low buffer concentrations. In this work, 10 microL samples of a 50 mM probe solution were injected into C(18)-bonded columns using a series of five buffered mobile phases at (SW)pH between 2 and 12. The retention times and the shapes of the bands were analyzed based on thermodynamic arguments. A new adsorption model that takes into account the simultaneous adsorption of the acidic and the basic species onto the endcapped adsorbent, predicts accurately the complex experimental profiles recorded. The adsorption mechanism of acido-basic compounds onto RPLC phases seems to be consistent with the following microscopic model. No matter whether the acid or the base is the neutral or the basic species, the neutral species adsorbs onto a large number of weak adsorption sites (their saturation capacity is several tens g/L and their equilibrium constant of the order of 0.1 L/g). In contrast, the ionic species adsorbs strongly onto fewer active sites (their saturation capacity is about 1g/L and their equilibrium constant of the order of a few L/g). From a microscopic point of view and in agreement with the adsorption isotherm of the compound measured by frontal analysis (FA) and with the results of Monte-Carlo calculations performed by Schure et al., the first type of adsorption sites are most likely located in between C(18)-bonded chains and the second type of adsorption sites are located deeper in contact with the silica surface. The injected concentration (50 mM) was too low to probe the weakest adsorption sites (saturation capacity of a few hundreds g/L with an equilibrium constant of one hundredth of L/g) that are located at the very interface between the C(18)-bonded layer and the bulk phase.

  8. Adsorption mechanism of acids and bases in reversed-phase liquid chromatography in weak buffered mobile phases designed for liquid chromatography/mass spectrometry

    SciTech Connect

    Gritti, Fabrice; Guiochon, Georges A

    2009-01-01

    The overloaded band profiles of five acido-basic compounds were measured, using weakly buffered mobile phases. Low buffer concentrations were selected to provide a better understanding of the band profiles recorded in LC/MS analyses, which are often carried out at low buffer concentrations. In this work, 10 {micro}L samples of a 50 mM probe solution were injected into C{sub 18}-bonded columns using a series of five buffered mobile phases at {sub W}{sup S}pH between 2 and 12. The retention times and the shapes of the bands were analyzed based on thermodynamic arguments. A new adsorption model that takes into account the simultaneous adsorption of the acidic and the basic species onto the endcapped adsorbent, predicts accurately the complex experimental profiles recorded. The adsorption mechanism of acido-basic compounds onto RPLC phases seems to be consistent with the following microscopic model. No matter whether the acid or the base is the neutral or the basic species, the neutral species adsorbs onto a large number of weak adsorption sites (their saturation capacity is several tens g/L and their equilibrium constant of the order of 0.1 L/g). In contrast, the ionic species adsorbs strongly onto fewer active sites (their saturation capacity is about 1 g/L and their equilibrium constant of the order of a few L/g). From a microscopic point of view and in agreement with the adsorption isotherm of the compound measured by frontal analysis (FA) and with the results of Monte-Carlo calculations performed by Schure et al., the first type of adsorption sites are most likely located in between C{sub 18}-bonded chains and the second type of adsorption sites are located deeper in contact with the silica surface. The injected concentration (50 mM) was too low to probe the weakest adsorption sites (saturation capacity of a few hundreds g/L with an equilibrium constant of one hundredth of L/g) that are located at the very interface between the C{sub 18}-bonded layer and the bulk

  9. Nitric acid uptake by sulfuric acid solutions under stratospheric conditions - Determination of Henry's Law solubility

    NASA Technical Reports Server (NTRS)

    Reihs, Christa M.; Golden, David M.; Tolbert, Margaret A.

    1990-01-01

    The uptake of nitric acid by sulfuric acid solutions representative of stratospheric particulate at low temperatures was measured to determine the solubility of nitric acid in sulfuric acid solutions as a function of H2SO4 concentration and solution temperature. Solubilities are reported for sulfuric acid solutions ranging from 58 to 87 wt pct H2SO4 over a temperature range from 188 to 240 K, showing that, in general, the solubility of nitric acid increases with decreasing sulfuric acid concentration and with decreasing temperature. The measured solubilities indicate that nitric acid in the global stratosphere will be found predominantly in the gas phase.

  10. Dependence of Device Characteristics of Bulk-Heterojunction Organic Thin-Film Solar Cells on Concentration of Glycerol and Sorbitol Addition in Pedot:. PSS Solutions for Fabricating Buffer Layers

    NASA Astrophysics Data System (ADS)

    Yamaki, Yusuke; Marumoto, Kazuhiro; Fujimori, Takuya; Mori, Tatsuo

    We have investigated the dependence of device characteristics of bulk-heterojunction organic thin-film solar cells on the concentration of glycerol and sorbitol addition in poly(3,4-ethylenedioxy thiophene):poly(4-styrene sulfonate) (PEDOT:PSS) solutions for fabricating buffer layers. The device structure is ITO/buffer/regioregular poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C61-butyric acid methylester (PCBM)/Al. Glycerol addition is effective for increasing power conversion efficiency (PCE) from 1.25 to 1.41% because of the increase in short-circuit current density (Jsc) without decreasing open-circuit voltage (Voc). On the other hand, sorbitol addition decreases PCE from 1.25 to 1.04%, owing to the decrease in Voc. This difference in Voc behavior is ascribed to different work function of PEDOT:PSS with glycerol and sorbitol treatment.

  11. Corrosion Behavior of Ultra-fine Grained 1050 Aluminum Alloy Fabricated by ARB Process in a Buffer Borate Solution

    NASA Astrophysics Data System (ADS)

    Fattah-alhosseini, A.; Gashti, S. O.

    2015-09-01

    Accumulative roll bonding (ARB) has been used as a severe plastic deformation process for the industrial production of ultra-fine grained (UFG) and nano-crystalline sheets with excellent mechanical properties. In the present study, the effect of the ARB process on the corrosion behavior of UFG and nano-crystalline 1050 aluminum alloy in a buffer borate solution (pH 5.5) has been investigated. The result of microhardness tests revealed that microhardness values increase with an increasing number of ARB cycles. A sharp increase in microhardness is seen after three ARB cycles, whereas moderate additional increases are observed afterward for up to nine cycles. Also, the XRD results showed that the mean crystallite size decreased to about 91 nm after nine cycles. The potentiodynamic plots show that as a result of ARB, the corrosion behavior of the UFG and nano-crystalline specimens improves, compared to the annealed 1050 aluminum alloy. Moreover, electrochemical impedance spectroscopy measurements showed that the polarization resistance increases with an increasing number of ARB cycles.

  12. Repassivation behavior of 316L stainless steel in borate buffer solution: Kinetics analysis of anodic dissolution and film formation

    NASA Astrophysics Data System (ADS)

    Xu, Haisong; Sun, Dongbai; Yu, Hongying

    2015-12-01

    The repassivation behavior of metals or alloys after oxide film damage determines the development of local corrosion and corrosion resistance. In this work, the repassivation kinetics of 316L stainless steel (316L SS) are investigated in borate buffer solution (pH 9.1) by using the abrading electrode technique. The current densities flowing from bare 316L SS surface are measured by potentiostatic method and analyzed to characterize repassivation kinetics. The initial stages of current decay (t < 500 ms) are discussed according to a film growth model, which describes the initial current transient should be divided into substrate dissolution current and passive film formation current based on Avrami kinetics. Then the two independent components are analyzed individually. The film formation rate and the thickness of film are compared in different applied potential. It is shown that anodic dissolution dominates the repassivation for a short time during the early times, and a higher applied potential will promote the anodic dissolution of metal. The film growth rate increases slightly with increasing in potential. Correspondingly, increase in applied potential from 0 VSCE to 0.8 VSCE results in thicker monolayer, which covers the whole bare surface at the time of θ = 1. The electric field strengths through the thin passive film could reach 3.97 × 106 V cm-1.

  13. Evaluation of different approaches to quantify strong organic acidity and acid-base buffering of organic-rich surface waters in Sweden.

    PubMed

    Köhler, Stephan; Hruska, Jakub; Jönsson, Jörgen; Lövgren, Lars; Lofts, Stephen

    2002-11-01

    The role of organic acids in buffering pH in surface waters has been studied using a small brownwater stream (26mg L(-1) TOC) draining a forested catchment in Northern Sweden. Under the conditions of elevated pressure of CO2 stream field pH was changed between 3.5 and 6.1 during the acidification and alkalinization experiment. Acid-base characteristics of the natural organic matter were also determined using a high precision potentiometric method for a concentrated sample from the same stream. We compared the predictions from the Windermere Humic Aqueous Model (WHAM Model V), a model derived from the potentiometric titration (diprotic/monoprotic acid model) and a previously derived triprotic acid model which only uses alkalinity and TOC as input variables. The predicted buffering characteristics of all three models are very similar in the pH range 4.5-7 which suggests that during routine analysis alkalinity and TOC are sufficient to give a good estimate of organic acid anion charge contribution in a large range of surface waters. A slightly adjusted version of WHAM V successfully describes the organic charge contribution in a large number of sampled surface water lakes, which were previously used to calibrate the triprotic model.

  14. The acid-base buffer capacity of podzolic soils and its changes under the impact of treatment with the Mehra-Jackson and Tamm reagents

    NASA Astrophysics Data System (ADS)

    Maksimova, Yu. G.; Maryakhina, N. N.; Tolpeshta, I. I.; Sokolova, T. A.

    2010-10-01

    The acid-base buffer capacity before and after the treatment with the Mehra-Jackson and Tamm reagents was assessed by continuous potentiometric titration for the main genetic horizons of two profiles of podzolic soils in the Central Forest State Reserve. The total buffer capacity was calculated in the pH range from the initial titration point (ITP) to 3 for the acid titration and from the ITP to 10 for the base titration, as well as the buffer capacities in the pH intervals of 0.25. It was found that both treatments abruptly decreased the base buffer capacity, which reached 70-90% in the E horizons. The high direct linear correlation of the difference between the total base buffer capacities before and after each treatment with the content of Fe in the Tamm extract was revealed. From the results obtained, a conclusion was drawn that finely dispersed Fe hydroxides were the main solid-phase constituents ensuring the base buffer capacity, and the deprotonation of hydroxyl groups on the surface of Fe hydroxides was the essential buffer reaction during the base titration.

  15. The effects of a simulated acid precipitation on leaf litter quality and the growth of a detritivore in a buffered lotic system.

    PubMed

    Garden, A; Davies, R W

    1988-01-01

    The effects of a simulated acid rain on leaf litter quality and the growth of a detritivore in a buffered lotic system were investigated. Exposure of Populus balsamifera L. saplings to a simulated acid precipitation prior to leaf abscission resulted in significant decreases in foliar nitrogen content and increases in carbon: nitrogen ratios. During decomposition of the leaf litter in a buffered lotic system, microbial activity was significantly reduced. Growth of Tipula commiscibilis Diane (Diptera: Tipulidae) larvae decreased significantly when fed conditioned leaves exposed to a simulated acid precipitation prior to abscission. Reductions in detritivore growth were correlated with lower potential quality of the leaf litter resulting from increased carbon: nitrogen ratios and reduced levels of microbial activity. Thus, even in well buffered freshwater ecosystems, acid precipitation can have significant indirect effects on microbial activity and macroinvertebrate growth.

  16. The effects of a simulated acid precipitation on leaf litter quality and the growth of a detritivore in a buffered lotic system.

    PubMed

    Garden, A; Davies, R W

    1988-01-01

    The effects of a simulated acid rain on leaf litter quality and the growth of a detritivore in a buffered lotic system were investigated. Exposure of Populus balsamifera L. saplings to a simulated acid precipitation prior to leaf abscission resulted in significant decreases in foliar nitrogen content and increases in carbon: nitrogen ratios. During decomposition of the leaf litter in a buffered lotic system, microbial activity was significantly reduced. Growth of Tipula commiscibilis Diane (Diptera: Tipulidae) larvae decreased significantly when fed conditioned leaves exposed to a simulated acid precipitation prior to abscission. Reductions in detritivore growth were correlated with lower potential quality of the leaf litter resulting from increased carbon: nitrogen ratios and reduced levels of microbial activity. Thus, even in well buffered freshwater ecosystems, acid precipitation can have significant indirect effects on microbial activity and macroinvertebrate growth. PMID:15092603

  17. Geographical variation of the acid buffering of vegetated catchments: Factors determining the bicarbonate leaching

    NASA Astrophysics Data System (ADS)

    Ohte, Nobuhito; Tokuchi, Naoko

    1999-12-01

    In order to understand the determining factors of the geographical variation of buffering in the world's vegetated catchments, this study examined the HCO3- leaching of 107 experimental watersheds selected from regions ranging from tropical rain forests to humid continental or subpolar forests including several temperate grassland. With consideration of the soil development and the factors controlling it, the influences of geological, climatological, and topographical conditions on discharge HCO3- concentrations and fluxes are examined. The HCO3- discharge fluxes from catchments were correlated with climatological indexes. The increase of annual mean temperature reflected the increase in fluxes, although this tendency was not that significant in the precipitation-flux relationships. Notable differences in these correlations were not found among three major groups of bedrock types; igneous, metamorphic, and sedimentary groups, with exceptions being noted at the sites having materially HCO3--rich calcite, dolomite and volcanic ash. There were, however, exceptionally high flux sites whose fluxes could not be predicted by the empirical model when considering only temperature and precipitation controls. These sites belong to the mountainous part of the Japanese archipelago that is orogenically active and have in common steep hillslopes. Positive correlations were found between relief ratio, which was calculated by dividing elevation difference between highest and lowest points in the catchment by the distance between those two points, and fluxes in igneous and sedimentary groups including these high- HCO3- flux sites. These facts suggest that it is a fundamental requirement to consider the status of the soil forming when discussing the global variations in the buffering of watersheds. The differences in geomorphologic conditions controlling soil development are also just as important as the climatological effects.

  18. An experimental study of zinc chloride speciation from 300 to 600 °C and 0.5 to 2.0 kbar in buffered hydrothermal solutions

    USGS Publications Warehouse

    Cygan, G.L.; Hemley, J.J.; d'Angelo, W. M.

    1994-01-01

    The solubility of sphalerite (ZnS) was measured in KCl-HCl-H2O solutions at 300-600??C and 0.5-2.0 kbar. The silicate assemblage K-feldspar-muscovite (or andalusite)-quartz was used to buffer the solution to acid conditions, resulting in the total solubility reaction 2K+ + KAl2AlSi3O10(OH)2 + 6SiO2 + ZnS + nCl- = ZnCln(2-n) + 3KAlSi3O8 + H2S. (muscovite) (quartz) (sphalerite) (K-feldspar) A computer retrieval technique was used to derive average chloride ligand numbers for chlorozinc species at 0.25-2.0 molal total chloride. This technique mathematically solves for the average ligand number using a series of pertinent chemical relations at P and T. Mono- and di-chlorozinc species were found to predominate throughout the pressure-temperature-composition range investigated. The logarithms of the first and second dissociation constants for ZnCl20 were evaluated over the P-T range; for example, at 1 kbar, the values -0.41 and -1.42 were computed for the logarithm of the first dissociation constant, while -7.62 and -10.57 were computed for the logarithm of the second dissociation constant, for 400 and 500??C, respectively. Results are compared to past studies conducted at subcritical conditions and differ in that we find no evidence for more highly coordinated chloro-zinc species except possibly for ZnCl3- at 600??C, 1 and 2 kbar. Our results are consistent with electrostatic theory, which favors lower charged to neutral molecules in low dielectric-constant media. ?? 1994.

  19. Acidification and buffering mechanisms in acid sulfate soil wetlands of the Murray-Darling Basin, Australia.

    PubMed

    Glover, Fiona; Whitworth, Kerry L; Kappen, Peter; Baldwin, Darren S; Rees, Gavin N; Webb, John A; Silvester, Ewen

    2011-04-01

    The acid generation mechanisms and neutralizing capacities of sulfidic sediments from two inland wetlands have been studied in order to understand the response of these types of systems to drying events. The two systems show vastly different responses to oxidation, with one (Bottle Bend (BB) lagoon) having virtually no acid neutralizing capacity (ANC) and the other (Psyche Bend (PB) lagoon) an ANC that is an order of magnitude greater than the acid generation potential. While BB strongly acidifies during oxidation the free acid generation is less than that expected from the measured proton production and consumption processes, with additional proton consumption attributed to the formation of an acid-anion (chloride) FeIII (oxyhydr)oxide product, similar to akaganéite (Fe(OH)2.7Cl0.3). While such products can partially attenuate the acidification of these systems, resilience to acidification is primarily imparted by sediment ANC. PMID:21375259

  20. Kinetic buffers.

    PubMed

    Alibrandi, Giuseppe; Fabbrizzi, Luigi; Licchelli, Maurizio; Puglisi, Antonio

    2015-01-12

    This paper proposes a new type of molecular device that is able to act as an inverse proton sponge to slowly decrease the pH inside a reaction vessel. This makes the automatic monitoring of the concentration of pH-sensitive systems possible. The device is a composite formed of an alkyl chloride, which kinetically produces acidity, and a buffer that thermodynamically modulates the variation in pH value. Profiles of pH versus time (pH-t plots) have been generated under various experimental conditions by computer simulation, and the device has been tested by carrying out automatic spectrophotometric titrations, without using an autoburette. To underline the wide variety of possible applications, this new system has been used to realize and monitor HCl uptake by a di-copper(II) bistren complex in a single run, in a completely automatic experiment.

  1. Process for the recovery of strontium from acid solutions

    DOEpatents

    Horwitz, E. Philip; Dietz, Mark L.

    1992-01-01

    The invention is a process for selectively extracting strontium and technetium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant is a macrocyclic polyether in a diluent which is insoluble in water, but which will itself dissolve a small amount of water. The process will extract strontium and technetium values from nitric acid solutions which are up to 6 molar in nitric acid.

  2. Process for the recovery of strontium from acid solutions

    DOEpatents

    Horwitz, E.P.; Dietz, M.L.

    1992-03-31

    The invention is a process for selectively extracting strontium and technetium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant is a macrocyclic polyether in a diluent which is insoluble in water, but which will itself dissolve a small amount of water. The process will extract strontium and technetium values from nitric acid solutions which are up to 6 molar in nitric acid. 5 figs.

  3. Process for the recovery of strontium from acid solutions

    SciTech Connect

    Horwitz, E.P.; Dietz, M.L.

    1990-12-31

    The invention is a process for selectively extracting strontium and technetium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant is a macrocyclic polyether in a diluent which is insoluble in water, but which will itself dissolve a small amount of water. The process will extract strontium and technetium values from nitric acid solutions which are up to 6 molar in nitric acid.

  4. Long-term stability of earthen materials in contact with acidic tailings solutions

    SciTech Connect

    Peterson, S.R.; Erikson, R.L.; Gee, G.W.

    1982-11-01

    The objectives of the studies documented in this report were to use experimental and geochemical computer modeling tools to assess the long-term environmental impact of leachate movement from acidic uranium mill tailings. Liner failure (i.e., an increase in the permeability of the liner material) was not found to be a problem when various acidic tailings solutions leached through liner materials for periods up to 3 years. On the contrary, materials that contained over 30% clay showed a decrease in permeability with time in the laboratory columns. The high clay materials tested appear suitable for lining tailings impoundment ponds. The decreases in permeability are attributed to pore plugging resulting from the precipitation of minerals and solids. This precipitation takes place due to the increase in pH of the tailings solution brought about by the buffering capacity of the soil. Geochemical modeling predicts, and x-ray characterization confirms, that precipitation of solids from solution is occurring in the acidic tailings solution/liner interactions studied. In conclusion the same mineralogical changes and contaminant reactions predicted by geochemical modeling and observed in laboratory studies were found at a drained evaporation pond (Lucky Mc in Wyoming) with a 4 year history of acid attack.

  5. Influence of the acid buffering capacity of different types of Technosols on the chemistry of their leachates.

    PubMed

    Yao, F X; Macías, F; Santesteban, A; Virgel, S; Blanco, F; Jiang, X; Camps Arbestain, M

    2009-01-01

    The preparation of tailor-made Technosols from wastes may be a novel and prospective option for the re-use of wastes and restoration of degraded areas. A two-month study with pilot columns was conducted to evaluate the influence of the acid buffering capacity of different Technosols on the chemistry of their leachates. The Technosols were made from mixtures of organic and inorganic wastes at a ratio of 56:44 (w/w). The organic components used were an anaerobic (AN) and an aerobic (AE) sewage sludge. The inorganic wastes used--referred to as "conditioners"--were Linz-Donowitz slag (LD) and foundry sand (FS). A mixture of the two conditioners at a ratio of 50:50 (w/w) was made to provide a third type of conditioner (LD+FS). Controls consisted of columns filled with organic waste only (either AN or AE sludges). Changes in pH, electrical conductivity, concentrations of major ions and dissolved organic carbon in the leachates were evaluated periodically. The main processes determining the pH of the systems were nitrification and leaching, but organic matter decomposition and carbonation may also have had an influence. Nitrification was strongly retarded in the AN sludge (attributed to the probable absence of nitrifiers in this waste after the AN wastewater treatment) and was impeded in those mixtures in which LD was used as a component (due to the liming effect). Final pH values ranged from 5.0 and 5.4 (in AE and AE+FS, respectively) to 11.1 (in AN+LD). The pH of the other mixtures finally ranged between 7 and 8. In formulating mixtures of wastes, their acid buffering capacity should be taken into account in addition to the nutrient contents and the limits of contaminants established by local regulations. PMID:19026435

  6. Effect of Organic Acid Additions on the General and Localized Corrosion Susceptibility of Alloy 22 in Chloride Solutions

    SciTech Connect

    Carranza, R M; Giordano, C M; Rodr?guez, M A; Ilevbare, G O; Rebak, R B

    2007-08-28

    Electrochemical studies such as cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 (N06022) in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. All the tested material was wrought Mill Annealed (MA). Tests were also performed in NaCl solutions containing weak organic acids such as oxalic, acetic, citric and picric. Results show that the corrosion rate of Alloy 22 was significantly higher in solutions containing oxalic acid than in solutions of pure NaCl at the same pH. Citric and picric acids showed a slightly higher corrosion rate, and acetic acid maintained the corrosion rate of pure chloride solutions at the same pH. Organic acids revealed to be weak inhibitors for crevice corrosion. Higher concentration ratios, compared to nitrate ions, were needed to completely inhibit crevice corrosion in chloride solutions. Results are discussed considering acid dissociation constants, buffer capacity and complex formation constants of the different weak acids.

  7. REDUCTION OF ACIDITY OF NITRIC ACID SOLUTIONS BY USE OF FORMALDEHYDE

    DOEpatents

    Healy, T.V.

    1958-05-20

    A continuous method is described of concentrating by evaporation and reducing the nitrate ion content of an aqueous solution of metallic salts containing nitric acid not in excess of 8N. It consists of heating the solution and then passing formaldehyde into the heated solution to bring about decomposition of the nitric acid. The evolved gases containing NO are contacted countercurrently with an aqueous metal salt solution containing nitric acid in excess of 8N so as to bring about decomposition of the nitric acid and lower the normality to at least 8N, whereupon it is passed into the body of heated solution.

  8. Method for liquid chromatographic extraction of strontium from acid solutions

    DOEpatents

    Horwitz, E. Philip; Dietz, Mark L.

    1992-01-01

    A method and apparatus for extracting strontium and technetium values from biological, industrial and environmental sample solutions using a chromatographic column is described. An extractant medium for the column is prepared by generating a solution of a diluent containing a Crown ether and dispersing the solution on a resin substrate material. The sample solution is highly acidic and is introduced directed to the chromatographic column and strontium or technetium is eluted using deionized water.

  9. Retention of ionisable compounds on high-performance liquid chromatography XVIII: pH variation in mobile phases containing formic acid, piperazine, tris, boric acid or carbonate as buffering systems and acetonitrile as organic modifier.

    PubMed

    Subirats, Xavier; Bosch, Elisabeth; Rosés, Martí

    2009-03-20

    In the present work dissociation constants of commonly used buffering species, formic acid, piperazine, tris(hydroxymethyl)-aminomethane, boric acid and carbonate, have been determined for several acetonitrile-water mixtures. From these pK(a) values a previous model has been successfully evaluated to estimate pH values in acetonitrile-aqueous buffer mobile phases from the aqueous pH and concentration of the above mentioned buffers up to 60% of acetonitrile, and aqueous buffer concentrations between 0.005 (0.001 mol L(-1) for formic acid-formate) and 0.1 mol L(-1). The relationships derived for the presently studied buffers, together with those established for previously considered buffering systems, allow a general prediction of the pH variation of the most commonly used HPLC buffers when the composition of the acetonitrile-water mobile phase changes during the chromatographic process, such as in gradient elution. Thus, they are an interesting tool that can be easily implemented in general retention models to predict retention of acid-base analytes and optimize chromatographic separations.

  10. Retention of ionisable compounds on high-performance liquid chromatography XIX. pH variation in mobile phases containing formic acid, piperazine and tris as buffering systems and methanol as organic modifier.

    PubMed

    Subirats, Xavier; Bosch, Elisabeth; Rosés, Martí

    2009-07-10

    In previous works a model to estimate the pH of methanol-aqueous buffer mobile phases from the aqueous pH and concentration of the buffer and the fraction of organic modifier was developed. This model was successfully applied and validated for buffers prepared from ammonia, acetic, phosphoric and citric acids. In the present communication this model has been extended to formic acid, piperazine and tris(hydroxymethyl)aminomethane buffers. Prior to the modelling work, the pK(a) values of the studied buffers at several methanol-water compositions were determined.

  11. Corrosion of dental amalgams in solutions of organic acids.

    PubMed

    Palaghias, G

    1986-06-01

    A conventional and two high copper amalgams were tested in 0.5% aqueous solutions of acetic, formic, lactic and succinic acid. The corrosion behavior of the amalgams in the different solutions was evaluated by analyzing the soluble corrosion products using an atomic absorption spectrophotometer every month during a 6-month experimental period. The high copper amalgams showed a high dissolution rate in formic and lactic acid solutions from the initial stages of immersion when compared to the conventional. Later a marked decrease of the dissolution rate could be observed but it still remained at high levels. In acetic acid the amounts of elements dissolved from high copper amalgams were much less. Conventional amalgam released much smaller amounts of elements in almost all solutions tested except in the case of silver in lactic acid. Finally, in succinic acid solution, the amounts of elements dissolved were unexpectedly small considering the low pH of the solution and the dissolution rates of the amalgams in the other organic acid solutions. PMID:3461548

  12. Decomposition Studies of Triphenylboron, Diphenylborinic Acid and Phenylboric Acid in Aqueous Alkaline Solutions Containing Copper

    SciTech Connect

    Crawford, C.L.; Peterson, R. A.

    1997-02-11

    This report documents the copper-catalyzed chemical kinetics of triphenylboron, diphenylborinic acid and phenylboric acid (3PB, 2PB and PBA) in aqueous alkaline solution contained in carbon-steel vessels between 40 and 70 degrees C.

  13. Vacuum-jacketed hydrofluoric acid solution calorimeter

    USGS Publications Warehouse

    Robie, R.A.

    1965-01-01

    A vacuum-jacketed metal calorimeter for determining heats of solution in aqueous HF was constructed. The reaction vessel was made of copper and was heavily gold plated. The calorimeter has a cooling constant of 0.6 cal-deg -1-min-1, approximately 1/4 that of the air-jacketed calorimeters most commonly used with HF. It reaches equilibrium within 10 min after turning off the heater current. Measurements of the heat of solution of reagent grade KCl(-100 mesh dried 2 h at 200??C) at a mole ratio of 1 KCl to 200 H2O gave ??H = 4198??11 cal at 25??C. ?? 1965 The American Institute of Physics.

  14. Nylon Dissolution in Nitric Acid Solutions

    SciTech Connect

    KESSINGER, GLENF.

    2004-06-16

    H Area Operations is planning to process Pu-contaminated uranium scrap in support of de-inventory efforts. Nylon bags will be used to hold materials to be dissolved in H-Canyon. Based on this set of twelve nylon dissolutions, it is concluded that (when other variables are held constant): increased acid concentration results in increased dissolution rates; increased acid concentration results in a lower dissolution onset temperature; little, if any, H plus is consumed during the depolymerization process; and 2.0-3.0 M HNO3, with 0.025 M KF and 2 g/L B, is satisfactory for the dissolution of nylon bag materials to be used during H-Canyon processing.

  15. Raman spectra of amino acids and their aqueous solutions

    NASA Astrophysics Data System (ADS)

    Zhu, Guangyong; Zhu, Xian; Fan, Qi; Wan, Xueliang

    2011-03-01

    Amino acids are the basic "building blocks" that combine to form proteins and play an important physiological role in all life-forms. Amino acids can be used as models for the examination of the importance of intermolecular bonding in life processes. Raman spectra serve to obtain information regarding molecular conformation, giving valuable insights into the topology of more complex molecules (peptides and proteins). In this paper, amino acids and their aqueous solution have been studied by Raman spectroscopy. Comparisons of certain values for these frequencies in amino acids and their aqueous solutions are given. Spectra of solids when compared to those of the solute in solution are invariably much more complex and almost always sharper. We present a collection of Raman spectra of 18 kinds of amino acids ( L-alanine, L-arginine, L-aspartic acid, cystine, L-glutamic acid, L-glycine, L-histidine, L-isoluecine, L-leucine, L-lysine, L-phenylalanine, L-methionone, L-proline, L-serine, L-threonine, L-tryptophan, L-tyrosine, L-valine) and their aqueous solutions that can serve as references for the interpretation of Raman spectra of proteins and biological materials.

  16. Polymerization of beta-amino acids in aqueous solution

    NASA Technical Reports Server (NTRS)

    Liu, R.; Orgel, L. E.; Bada, J. L. (Principal Investigator)

    1998-01-01

    We have compared carbonyl diimidazole (CDI) and 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDAC) as activating agents for the oligomerization of negatively-charged alpha- and beta-amino acids in homogeneous aqueous solution. alpha-Amino acids can be oligomerized efficiently using CDI, but not by EDAC. beta-Amino acids can be oligomerized efficiently using EDAC, but not by CDI. Aspartic acid, an alpha- and beta-dicarboxylic acid is oligomerized efficiently by both reagents. These results are explained in terms of the mechanisms of the reactions, and their relevance to prebiotic chemistry is discussed.

  17. Novel Regenerated Solvent Extraction Processes for the Recovery of Carboxylic Acids or Ammonia from Aqueous Solutions Part I. Regeneration of Amine-Carboxylic Acid Extracts

    SciTech Connect

    Poole, L.J.; King, C.J.

    1990-03-01

    Two novel regenerated solvent extraction processes are examined. The first process has the potential to reduce the energy costs inherent in the recovery of low-volatility carboxylic acids from dilute aqueous solutions. The second process has the potential for reducing the energy costs required for separate recovery of ammonia and acid gases (e.g. CO{sub 2} and H{sub 2}S) from industrial sour waters. The recovery of carboxylic acids from dilute aqueous solution can be achieved by extraction with tertiary amines. An approach for regeneration and product recovery from such extracts is to back-extract the carboxylic acid with a water-soluble, volatile tertiary amine, such as trimethylamine. The resulting trimethylammonium carboxylate solution can be concentrated and thermally decomposed, yielding the product acid and the volatile amine for recycle. Experimental work was performed with lactic acid, succinic acid, and fumaric acid. Equilibrium data show near-stoichiometric recovery of the carboxylic acids from an organic solution of Alamine 336 into aqueous solutions of trimethylamine. For fumaric and succinic acids, partial evaporation of the aqueous back extract decomposes the carboxylate and yields the acid product in crystalline form. The decomposition of aqueous solutions of trimethylammonium lactates was not carried out to completion, due to the high water solubility of lactic acid and the tendency of the acid to self-associate. The separate recovery of ammonia and acid gases from sour waters can be achieved by combining steam-stripping of the acid gases with simultaneous removal of ammonia by extraction with a liquid cation exchanger. The use of di-2,4,4-trimethylpentyl phosphinic acid as the liquid cation exchanger is explored in this work. Batch extraction experiments were carried out to measure the equilibrium distribution ratio of ammonia between an aqueous buffer solution and an organic solution of the phosphinic acid (0.2N) in Norpar 12. The concentration

  18. Effect of HEPES buffer on the uptake and transport of P-glycoprotein substrates and large neutral amino acids

    PubMed Central

    Luo, Shuanghui; Pal, Dhananjay; Shah, Sujay J.; Kwatra, Deep; Paturi, Kalyani D.; Mitra, Ashim. K.

    2010-01-01

    HEPES has been widely employed as an organic buffer agent in cell culture medium as well as uptake and transport experiments in vitro. However, concentrations of HEPES used in such studies vary from one laboratory to another. In this study, we investigated the effect of HEPES on the uptake and bidirectional transport of P-gp substrates employing both Caco-2 and MDCK-MDR1 cells. ATP-dependent uptake of glutamic acid was also examined. ATP production was further quantified applying ATP Determination Kit. An addition of HEPES to the cellular washing and incubation media significantly altered the uptake and transport of P-gp substrates in both Caco-2 and MDCK-MDR1 cells. Uptake of P-gp substrates substantially diminished as the HEPES concentration was raised to 25 mM. Bidirectional (A-B and B-A) transport studies revealed that permeability ratio of PappB-A to PappA-B in the presence of 25 mM HEPES was significantly higher than control. The uptake of phenylalanine is an ATP-independent process, whereas the accumulation of glutamic acid is ATP-dependent. While phenylalanine uptake remained unchanged glutamic acid uptake was elevated with the addition of HEPES. Verapamil is an inhibitor of P-gp mediated uptake, elevation of cyclosporine uptake in the presence of 5 μM verapamil was compromised by the presence of 25 mM HEPES. The results of ATP assay indicated that HEPES stimulated the production of ATP. This study suggests that the addition of HEPES in the medium modulated the energy dependent efflux and uptake processes. The effect of HEPES on P-gp mediated drug efflux and transport may provide some mechanistic insight into possible reasons for inconsistencies in the results reported from various laboratories. PMID:20163160

  19. Improved method for extracting lanthanides and actinides from acid solutions

    DOEpatents

    Horwitz, E.P.; Kalina, D.G.; Kaplan, L.; Mason, G.W.

    1983-07-26

    A process for the recovery of actinide and lanthanide values from aqueous acidic solutions uses a new series of neutral bi-functional extractants, the alkyl(phenyl)-N,N-dialkylcarbamoylmethylphosphine oxides. The process is suitable for the separation of actinide and lanthanide values from fission product values found together in high-level nuclear reprocessing waste solutions.

  20. Precipitation of plutonium from acidic solutions using magnesium oxide

    SciTech Connect

    Jones, S.A.

    1994-12-05

    Magnesium oxide will be used as a neutralizing agent for acidic plutonium-containing solutions. It is expected that as the magnesium oxide dissolves, the pH of the solution will rise, and plutonium will precipitate. The resulting solid will be tested for suitability to storage. The liquid is expected to contain plutonium levels that meet disposal limit requirements.

  1. Method for incorporating radioactive phosphoric acid solutions in concrete

    DOEpatents

    Wolf, Gary A [Kennewick, WA; Smith, Jeffrey W [Lancaster, OH; Ihle, Nathan C [Walla Walla, WA

    1984-01-01

    A method for incorporating radioactive phosphoric acid solutions in concrete is described wherein the phosphoric acid is reacted with Ca(OH).sub.2 to form a precipitate of hydroxyapatite and the hydroxyapatite is mixed with portland cement to form concrete.

  2. Method for incorporating radioactive phosphoric acid solutions in concrete

    DOEpatents

    Wolf, G.A.; Smith, J.W.; Ihle, N.C.

    1982-07-08

    A method for incorporating radioactive phosphoric acid solutions in concrete is described wherein the phosphoric acid is reacted with Ca(OH)/sub 2/ to form a precipitate of hydroxyapatite and the hydroxyapatite is mixed with Portland cement to form concrete.

  3. Immunolocalization of MAP-2 in Routinely Formalin-Fixed, Paraffin-Embedded Guinea Pig Brain Sections Using Microwave Irradiation: A Comparison of Different Combinations of Antibody Clones and Antigen Retrieval Buffer Solutions

    NASA Astrophysics Data System (ADS)

    Kan, Robert K.; Pleva, Christina M.; Hamilton, Tracey A.; Petrali, John P.

    2005-04-01

    The present study was designed to evaluate the efficacy of different microwave pretreatment methods to retrieve microtubule-associated protein 2 (MAP-2) immunoreactivity in formalin-fixed, paraffin-embedded guinea pig brain sections. Brain sections, microwave pretreated in boiling sodium citrate, citric acid, Tris hydrochloride, and EDTA buffers of pH 4, 6, and 8, were labeled with four different clones of MAP-2 monoclonal antibodies. No MAP-2 immunoreactivity was observed in control sections processed without microwave pretreatment. Optimal MAP-2 immunoreactivity was observed only when MAP-2 antibody clone AP18 was used in conjunction with citric acid buffer of pH 6.0. Using this combination, brain sections from nerve agent soman-exposed guinea pigs were found to exhibit marked reduction in MAP-2 immunostaining in the hippocampus. These observations suggest that the clone of the antibody in addition to the type and pH of antigen retrieval (AR) solution are important variables to be considered for establishing an optimal AR technique. When studying counterpart antigens of species other than that to which the antibodies were originally raised, different antibody clones must be tested in combination with different microwave-assisted AR (MAR) methods. This MAR method makes it possible to conduct retrospective studies on archival guinea pig brain paraffin blocks to evaluate changes in neuronal MAP-2 expression as a consequence of chemical warfare nerve agent toxicity.

  4. Use of 8.4% Sodium Bicarbonate in Buffering Commonly Administered Vancomycin Hydrochloride Solutions for Use with Midline or Peripheral Line Catheters.

    PubMed

    Puertos, Enrique; Spencer, Melissa

    2015-01-01

    The primary objective of this study was to evaluate the use of 8.4% sodium bicarbonate in the buffering of commonly administered vancomycin hydrochloride solutions for use with midline or peripheral line catheters. Nine admixtures of vancomycin hydrochloride were aseptically prepared for this study. Vancomycin hydrochloride solutions were prepared in triplicates in the following strengths, 1 gram, 2 grams, and 3 grams, which were added to 250-mL bags of sodium chloride 0.9% injection (with overfill). To each prepared solution of vancomycin hydrochloride, 0.5 mL of 8.4% sodium bicarbonate was added. The pH was measured to obtain a baseline level. At day 9, the pH of each sample was measured and compared to those at baseline. The osmolality of each sample was also measured. There was no statistical difference in the pH at baseline and at day 9 (α = 0.05, P = 0.347). A solution of vancomycin hydrochloride that is compounded in 250 mL of sodium chloride 0.9% injection (including overfill) and buffered with 0.5 mL of 8.4% sodium bicarbonate maintained a pH in the range of 5 to 9 and an osmolality in the range of 150 mOsm/kg to 500 mOsm/kg.

  5. Phosphorylation of glyceric acid in aqueous solution using trimetaphosphate.

    PubMed

    Kolb, V; Orgel, L E

    1996-02-01

    The phosphorylation of glyceric acid is an interesting prebiotic reaction because it converts a simple, potentially prebiotic organic molecule into phosphate derivatives that are central to carbohydrate metabolism. We find that 0.05 M glyceric acid in the presence of 0.5 M trimetaphosphate in alkaline solution gives a mixture of 2- and 3-phosphoglyceric acids in combined yields of up to 40%. PMID:11536746

  6. Phosphorylation of Glyceric Acid in Aqueous Solution Using Trimetaphosphate

    NASA Technical Reports Server (NTRS)

    Kolb, Vera; Orgel, Leslie E.

    1996-01-01

    The phosphorylation of glyceric acid is an interesting prebiotic reaction because it converts a simple, potentially prebiotic organic molecule into phosphate derivatives that are central to carbohydrate metabolism. We find that 0.05 M glyceric acid in the presence of 0.5 M trimetaphosphate in alkaline solution gives a mixture of 2- and 3-phosphoglyceric acids in combined yields of up to 40%.

  7. Controlled release of acidic drugs in compendial and physiological hydrogen carbonate buffer from polymer blend-coated oral solid dosage forms.

    PubMed

    Wulff, R; Rappen, G-M; Koziolek, M; Garbacz, G; Leopold, C S

    2015-09-18

    The objective of this study was to investigate the suitability of "Eudragit® RL/Eudragit® L55" (RL/L55) blend coatings for a pH-independent release of acidic drugs. A coating for ketoprofen and naproxen mini tablets was developed showing constant drug release rate under pharmacopeial two-stage test conditions for at least 300 min. To simulate drug release from the mini tablets coated with RL/L55 blends in the gastrointestinal (GI) tract, drug release profiles in Hanks buffer pH 6.8 were recorded and compared with drug release profiles in compendial media. RL/L55 blend coatings showed increased drug permeability in Hanks buffer pH 6.8 compared to phosphate buffer pH 6.8 due to its higher ion concentration. However, drug release rates of acidic drugs were lower in Hanks buffer pH 6.8 because of the lower buffer capacity resulting in reduced drug solubility. Further dissolution tests were performed in Hanks buffer using pH sequences simulating the physiological pH conditions in the GI tract. Drug release from mini tablets coated with an RL/L55 blend (8:1) was insensitive to pH changes of the medium within the pH range of 5.8-7.5. It was concluded that coatings of RL/L55 blends show a high potential for application in coated oral drug delivery systems with a special focus on pH-independent release of acidic drugs.

  8. Initial inhomogeneity-induced crazy-clock behavior in the iodate-arsenous acid reaction in a buffered medium under stirred batch conditions.

    PubMed

    Valkai, László; Csekő, György; Horváth, Attila K

    2015-09-14

    It is unambiguously demonstrated that in the case of an autocatalytic reaction, initial inhomogeneities induced by the imperfectly mixed part of the overall volume may result in a serious irreproducibility of the individual kinetic runs. A statistically meaningful number of repetitions, however, gives rise to a reproducible cumulative probability distribution curve often referred to as a support of the stochastic feature. The iodate-arsenous acid reaction being autocatalytic with respect to both iodide and hydrogen ions displays clock behavior. However, the time lag necessary for the appearance of iodine, even in buffered solution, varies in an apparently random manner. Careful analysis of the variation of the different parameters like stirring rate, overall volume, geometry of the reactor and the way of mixing the reactants led us to conclude that the fate of the individual samples is determined at the initial stage when the reacting system is per se inhomogeneous. The place, the size of the so-called ignition volume, where the reacting system is imperfectly stirred, as well as the residence time spent there by the imperfectly mixed reactants all seem to depend on external factors. PMID:26239390

  9. Reduction of Plutonium in Acidic Solutions by Mesoporous Carbons

    DOE PAGES

    Parsons-Moss, Tashi; Jones, Stephen; Wang, Jinxiu; Wu, Zhangxiong; Uribe, Eva; Zhao, Dongyuan; Nitsche, Heino

    2015-12-19

    Batch contact experiments with several porous carbon materials showed that carbon solids spontaneously reduce the oxidation state of plutonium in 1-1.5 M acid solutions, without significant adsorption. The final oxidation state and rate of Pu reduction varies with the solution matrix, and also depends on the surface chemistry and surface area of the carbon. It was demonstrated that acidic Pu(VI) solutions can be reduced to Pu(III) by passing through a column of porous carbon particles, offering an easy alternative to electrolysis with a potentiostat.

  10. REMOVAL OF CHLORIDE FROM ACIDIC SOLUTIONS USING NO2

    SciTech Connect

    Visser, A; Robert Pierce, R; James Laurinat, J

    2006-08-22

    Chloride (Cl{sup -}) salt processing in strong acids is used to recycle plutonium (Pu) from pyrochemical residues. The Savannah River National Laboratory (SRNL) is studying the potential application of nitrogen dioxide (NO{sub 2}) gas to effectively convert dissolved pyrochemical salt solutions to chloride-free solutions and improve recovery operations. An NO{sub 2} sparge has been shown to effectively remove Cl{sup -} from solutions containing 6-8 M acid (H{sup +}) and up to 5 M Cl{sup -}. Chloride removal occurs as a result of the competition of at least two reactions, one which is acid-dependent. Below 4 M H+, NO2 reacts with Cl- to produce nitrosyl chloride (ClNO). Between 6 M and 8 M H{sup +}, the reaction of hydrochloric acid (HCl) with nitric acid (HNO{sub 3}), facilitated by the presence of NO{sub 2}, strongly affects the rate of Cl{sup -} removal. The effect of heating the acidic Cl{sup -} salt solution without pre-heating the NO{sub 2} gas has minimal effect on Cl{sup -} removal rates when the contact times between NO{sub 2} and the salt solution are on the order of seconds.

  11. Corrosion behavior of Mg-3Zn/bioglass (45S5) composite in simulated body fluid (SBF) and phosphate buffered saline (PBS) solution

    NASA Astrophysics Data System (ADS)

    Ab llah, N.; Jamaludin, S. B.; Daud, Z. C.; Zaludin, M. A. F.; Jamal, Z. A. Z.; Idris, M. S.; Osman, R. A. M.

    2016-07-01

    Magnesium has emerged as promising materials in biomaterials research due to its good mechanical and physical properties closer to human bones. However, magnesium has poor corrosion resistance to chloride ions that exist in human blood plasma thus preventing its application in biomedical. The addition of zinc and bioglass can reduce magnesium corrosion rate. In this work, the effect of different solution media (Simulated Body Fluid and Phosphate Buffered Saline) to the corrosion behavior of Mg-Zn/bioglass (45S5) composites was investigated. The composites of Mg-3Zn added with 5, 10, 15, 20, 15 and 30 wt. % bioglass were fabricated by powder metallurgy. The composites were prepared by mixing at 140 rpm for 1 hour, pressing at 500 MPa and sintering in an argon environment at a temperature of 450°C for 3 hours. Sintered samples were immersed in Simulated Body Fluid (SBF) and Phosphate Buffered Saline (PBS) in order to investigate the corrosion behavior. Samples mass loss was determined after 3 days of immersion. Samples microstructure and corrosion products were analyzed using optical microscope and x-ray diffraction (XRD) respectively. The results revealed that the samples immersed in the Phosphate Buffered Saline (PBS) shows lower mass loss compare to the samples immersed in the Simulated Body Fluid (SBF) for all composition except for Mg-3Zn without bio-glass. The results indicated that the existence of high phosphate ions in PBS has retarded the corrosion rate of composite Mg-3Zn/45S5. The pH value of the PBS solution after immersion showed significant increase between 10.3 and 11.09. Diffraction pattern (XRD) showed the presence of Mg(OH)2 as the major corrosion product for samples immersed in the SBF and PBS solutions. The mass loss of samples decreased with the addition of bio-glass.

  12. Optimization of the Energy Level Alignment between the Photoactive Layer and the Cathode Contact Utilizing Solution-Processed Hafnium Acetylacetonate as Buffer Layer for Efficient Polymer Solar Cells.

    PubMed

    Yu, Lu; Li, Qiuxiang; Shi, Zhenzhen; Liu, Hao; Wang, Yaping; Wang, Fuzhi; Zhang, Bing; Dai, Songyuan; Lin, Jun; Tan, Zhan'ao

    2016-01-13

    The insertion of an appropriate interfacial buffer layer between the photoactive layer and the contact electrodes makes a great impact on the performance of polymer solar cells (PSCs). Ideal interfacial buffer layers could minimize the interfacial traps and the interfacial barriers caused by the incompatibility between the photoactive layer and the electrodes. In this work, we utilized solution-processed hafnium(IV) acetylacetonate (Hf(acac)4) as an effective cathode buffer layer (CBL) in PSCs to optimize the energy level alignment between the photoactive layer and the cathode contact, with the short-circuit current density (Jsc), open-circuit voltage (Voc), and fill factor (FF) all simultaneously improved with Hf(acac)4 CBL, leading to enhanced power conversion efficiencies (PCEs). Ultraviolet photoemission spectroscopy (UPS) and scanning Kelvin probe microscopy (SKPM) were performed to confirm that the interfacial dipoles were formed with the same orientation direction as the built-in potential between the photoactive layer and Hf(acac)4 CBL, benefiting the exciton separation and electron transport/extraction. In addition, the optical characteristics and surface morphology of the Hf(acac)4 CBL were also investigated.

  13. Nogo goes in the pure water: solution structure of Nogo-60 and design of the structured and buffer-soluble Nogo-54 for enhancing CNS regeneration.

    PubMed

    Li, Minfen; Liu, Jingxian; Song, Jianxing

    2006-08-01

    The inability to determine the structure of the buffer-insoluble Nogo extracellular domain retarded further design of Nogo receptor (NgR) antagonists to treat CNS axonal injuries. Very surprisingly, we recently discovered that Nogo-60 was soluble and structured in salt-free water, thus allowing the determination of the first Nogo structure by heteronuclear NMR spectroscopy. Nogo-60 adopts an unusual helical structure with the N- and C-terminal helices connected by a long middle helix. While the N-helix has no contact with the rest of the molecule, the C-helix flips back to pack against the 20-residue middle helix. This packing appears to trigger the formation of the stable Nogo-60 structure because Nogo-40 with the last helix truncated is unstructured. The Nogo-60 structure offered us rationales for further design of the structured and buffer-soluble Nogo-54, which may be used as a novel NgR antagonist. Furthermore, our discovery may imply a general solution to solubilizing a category of buffer-insoluble proteins for urgent structural investigations. PMID:16877707

  14. Effect of Ethephon, Indole Butyric Acid, and Treatment Solution pH on Rooting and on Ethylene Levels within Mung Bean Cuttings.

    PubMed

    Mudge, K W; Swanson, B T

    1978-02-01

    Light-grown mung bean (Phaseolus aureus Roxb.) cuttings were treated with buffered and nonbuffered solutions of Ethephon, indole butyric acid (IBA), and the combination of both. Ethephon treatment resulted in increased tissue ethylene levels with increasing solution pH, but had no effect on rooting. IBA treatment had no effect on tissue ethylene levels, but strongly promoted rooting. Combinations of Ethephon and IBA had no effect on rooting of mung bean cuttings beyond that obtained by IBA alone. PMID:16660274

  15. Does Nitric Acid Dissociate at the Aqueous Solution Surface?

    SciTech Connect

    Lewis, Tanza; Winter, Berndt; Stern, Abraham C.; Baer, Marcel D.; Mundy, Christopher J.; Tobias, Douglas J.; Hemminger, J. C.

    2011-11-03

    Nitric acid is a prevalent component of atmospheric aerosols, and the extent of nitric acid dissociation at aqueous interfaces is relevant to its role in heterogeneous atmospheric chemistry. Several experimental and theoretical studies have suggested that the extent of dissociation of nitric acid near aqueous interfaces is less than in bulk solution. Here, dissociation of HNO3 at the surface of aqueous nitric acid is quantified using X-ray photoelectron spectroscopy of the nitrogen local electronic structure. The relative amounts of undissociated HNO3(aq) and dissociated NO3-(aq) are identified by the distinguishable N1s core-level photoelectron spectra of the two species, and we determine the degree of dissociation, αint, in the interface (the first ~3 layers of solution) as a function of HNO3 concentration. Our measurements show that dissociation is decreased by approximately 20% near the solution interface compared with bulk, and furthermore that dissociation occurs even in the top-most solution layer. The experimental results are supported by first-principles MD simulations, which show that hydrogen-bonds between HNO3 and water molecules at the solution surface stabilize the molecular form at low concentration, in analogy to the stabilization of molecular HNO3 that occurs in bulk solution at high concentration. This work was supported by the U.S. Department of Energy's (DOE) Office of Basic Energy Sciences, Chemical Sciences program. The Pacific Northwest National Laboratory is operated by Battelle for DOE.

  16. Activity of the Human Rhinovirus 3C Protease Studied in Various Buffers, Additives and Detergents Solutions for Recombinant Protein Production.

    PubMed

    Ullah, Raheem; Shah, Majid Ali; Tufail, Soban; Ismat, Fouzia; Imran, Muhammad; Iqbal, Mazhar; Mirza, Osman; Rhaman, Moazur

    2016-01-01

    Proteases are widely used to remove affinity and solubility tags from recombinant proteins to avoid potential interference of these tags with the structure and function of the fusion partner. In recent years, great interest has been seen in use of the human rhinovirus 3C protease owing to its stringent sequence specificity and enhanced activity. Like other proteases, activity of the human rhinovirus 3C protease can be affected in part by the buffer components and additives that are generally employed for purification and stabilization of proteins, hence, necessitate their removal by tedious and time-consuming procedures before proteolysis can occur. To address this issue, we examined the effect of elution buffers used for common affinity based purifications, salt ions, stability/solubility and reducing agents, and detergents on the activity of the human rhinovirus 3C protease using three different fusion proteins at 4°C, a temperature of choice for purification of many proteins. The results show that the human rhinovirus 3C protease performs better at 4°C than the frequently used tobacco etch virus protease and its activity was insensitive to most of the experimental conditions tested. Though number of fusion proteins tested is limited, we expect that these finding will facilitate the use of the human rhinovirus 3C protease in recombinant protein production for pharmaceutical and biotechnological applications. PMID:27093053

  17. Activity of the Human Rhinovirus 3C Protease Studied in Various Buffers, Additives and Detergents Solutions for Recombinant Protein Production.

    PubMed

    Ullah, Raheem; Shah, Majid Ali; Tufail, Soban; Ismat, Fouzia; Imran, Muhammad; Iqbal, Mazhar; Mirza, Osman; Rhaman, Moazur

    2016-01-01

    Proteases are widely used to remove affinity and solubility tags from recombinant proteins to avoid potential interference of these tags with the structure and function of the fusion partner. In recent years, great interest has been seen in use of the human rhinovirus 3C protease owing to its stringent sequence specificity and enhanced activity. Like other proteases, activity of the human rhinovirus 3C protease can be affected in part by the buffer components and additives that are generally employed for purification and stabilization of proteins, hence, necessitate their removal by tedious and time-consuming procedures before proteolysis can occur. To address this issue, we examined the effect of elution buffers used for common affinity based purifications, salt ions, stability/solubility and reducing agents, and detergents on the activity of the human rhinovirus 3C protease using three different fusion proteins at 4°C, a temperature of choice for purification of many proteins. The results show that the human rhinovirus 3C protease performs better at 4°C than the frequently used tobacco etch virus protease and its activity was insensitive to most of the experimental conditions tested. Though number of fusion proteins tested is limited, we expect that these finding will facilitate the use of the human rhinovirus 3C protease in recombinant protein production for pharmaceutical and biotechnological applications.

  18. Activity of the Human Rhinovirus 3C Protease Studied in Various Buffers, Additives and Detergents Solutions for Recombinant Protein Production

    PubMed Central

    Tufail, Soban; Ismat, Fouzia; Imran, Muhammad; Iqbal, Mazhar; Mirza, Osman; Rhaman, Moazur

    2016-01-01

    Proteases are widely used to remove affinity and solubility tags from recombinant proteins to avoid potential interference of these tags with the structure and function of the fusion partner. In recent years, great interest has been seen in use of the human rhinovirus 3C protease owing to its stringent sequence specificity and enhanced activity. Like other proteases, activity of the human rhinovirus 3C protease can be affected in part by the buffer components and additives that are generally employed for purification and stabilization of proteins, hence, necessitate their removal by tedious and time-consuming procedures before proteolysis can occur. To address this issue, we examined the effect of elution buffers used for common affinity based purifications, salt ions, stability/solubility and reducing agents, and detergents on the activity of the human rhinovirus 3C protease using three different fusion proteins at 4°C, a temperature of choice for purification of many proteins. The results show that the human rhinovirus 3C protease performs better at 4°C than the frequently used tobacco etch virus protease and its activity was insensitive to most of the experimental conditions tested. Though number of fusion proteins tested is limited, we expect that these finding will facilitate the use of the human rhinovirus 3C protease in recombinant protein production for pharmaceutical and biotechnological applications. PMID:27093053

  19. Aquatic photolysis: photolytic redox reactions between goethite and adsorbed organic acids in aqueous solutions

    USGS Publications Warehouse

    Goldberg, M.C.; Cunningham, K.M.; Weiner, Eugene R.

    1993-01-01

    Photolysis of mono and di-carboxylic acids that are adsorbed onto the surface of the iron oxyhydroxide (goethite) results in an oxidation of the organic material and a reduction from Fe(III) to Fe(II) in the iron complex. There is a subsequent release of Fe2+ ions into solution. At constant light flux and constant solution light absorption, the factors responsible for the degree of photolytic reaction include: the number of lattice sites that are bonded by the organic acid; the rate of acid readsorption to the surface during photolysis; the conformation and structure of the organic acid; the degree of oxidation of the organic acid; the presence or absence of an ??-hydroxy group on the acid, the number of carbons in the di-acid chain and the conformation of the di-acid. The ability to liberate Fe(III) at pH 6.5 from the geothite lattice is described by the lyotropic series: tartrate>citrate> oxalate > glycolate > maleate > succinate > formate > fumarate > malonate > glutarate > benzoate = butanoate = control. Although a larger amount of iron is liberated, the series is almost the same at pH 5.5 except that oxalate > citrate and succinate > maleate. A set of rate equations are given that describe the release of iron from the goethite lattice. It was observed that the pH of the solution increases during photolysis if the solutions are not buffered. There is evidence to suggest the primary mechanism for all these reactions is an electron transfer from the organic ligand to the Fe(III) in the complex. Of all the iron-oxyhydroxide materials, crystalline goethite is the least soluble in water; yet, this study indicates that in an aqueous suspension, iron can be liberated from the goethite lattice. Further, it has been shown that photolysis can occur in a multiphase system at the sediment- water interface which results in an oxidation of the organic species and release of Fe2+ to solution where it becomes available for further reaction. ?? 1993.

  20. γ-Irradiation of malic acid in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Negron-Mendoza, Alicia; Graff, Rebecca L.; Ponnamperuma, Cyril

    1980-12-01

    The γ-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the non-volatile products. Thin layer chromotography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the γ-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

  1. Real-time HD Exchange Kinetics of Proteins from Buffered Aqueous Solution with Electrothermal Supercharging and Top-Down Tandem Mass Spectrometry

    NASA Astrophysics Data System (ADS)

    Going, Catherine C.; Xia, Zijie; Williams, Evan R.

    2016-06-01

    Electrothermal supercharging (ETS) with electrospray ionization produces highly charged protein ions from buffered aqueous solutions in which proteins have native folded structures. ETS increases the charge of ribonuclease A by 34%, whereas only a 6% increase in charge occurs for a reduced-alkylated form of this protein, which is unfolded and its structure is ~66% random coil in this solution. These results indicate that protein denaturation that occurs in the ESI droplets is the primary mechanism for ETS. ETS does not affect the extent of solution-phase hydrogen-deuterium exchange (HDX) that occurs for four proteins that have significantly different structures in solution, consistent with a droplet lifetime that is considerably shorter than observable rates of HDX. Rate constants for HDX of ubiquitin are obtained with a spatial resolution of ~1.3 residues with ETS and electron transfer dissociation of the 10+ charge-state using a single capillary containing a few μL of protein solution in which HDX continuously occurs. HDX protection at individual residues with ETS HDX is similar to that with reagent supercharging HDX and with solution-phase NMR, indicating that the high spray potentials required to induce ETS do not lead to HD scrambling.

  2. Highly accurate boronimeter assay of concentrated boric acid solutions

    SciTech Connect

    Ball, R.M. )

    1992-01-01

    The Random-Walk Boronimeter has successfully been used as an on-line indicator of boric acid concentration in an operating commercial pressurized water reactor. The principle has been adapted for measurement of discrete samples to high accuracy and to concentrations up to 6000 ppm natural boron in light water. Boric acid concentration in an aqueous solution is a necessary measurement in many nuclear power plants, particularly those that use boric acid dissolved in the reactor coolant as a reactivity control system. Other nuclear plants use a high-concentration boric acid solution as a backup shutdown system. Such a shutdown system depends on rapid injection of the solution and frequent surveillance of the fluid to ensure the presence of the neutron absorber. The two methods typically used to measure boric acid are the chemical and the physical methods. The chemical method uses titration to determine the ionic concentration of the BO[sub 3] ions and infers the boron concentration. The physical method uses the attenuation of neutrons by the solution and infers the boron concentration from the neutron absorption properties. This paper describes the Random-Walk Boronimeter configured to measure discrete samples to high accuracy and high concentration.

  3. Radiolysis of aqueous solutions of 2-aminoethanethiosulfuric acid. [Gamma radiation

    SciTech Connect

    Grachev, S.A.; Koroleva, I.K.; Kropachev, E.V.; Litvyakova, G.I.

    1982-07-10

    In the radiolysis products of aerated and deaerated solutions of the 2-aminoethanethiosulfuric acid the authors have identified cystamine monoxide, cystamine, taurine, mercamine, the sulfate ion, the sulfite ion, and the dithionate ion. The yields of these products under different conditions have been determined. Results indicated that the sulfate ion is formed both from the divalent and the hexavalent sulfur atom of the 2-aminoethanethiosulfuric acid moelcule. A possible radiolysis mechanism is discussed.

  4. Natural dissolved organic matter mobilizes Cd but does not affect the Cd uptake by the green algae Pseudokirchneriella subcapitata (Korschikov) in resin buffered solutions.

    PubMed

    Verheyen, Liesbeth; Versieren, Liske; Smolders, Erik

    2014-09-01

    Natural dissolved organic matter (DOM) can have contrasting effects on metal bioaccumulation in algae because of complexation reactions that reduce free metal ion concentrations and because of DOM adsorption to algal surfaces which promote metal adsorption. This study was set up to reveal the role of different natural DOM samples on cadmium (Cd) uptake by the green algae Pseudokirchneriella subcapitata (Korschikov). Six different DOM samples were collected from natural freshwater systems and isolated by reverse osmosis. In addition, one (13)C enriched DOM sample was isolated from soil to trace DOM adsorption to algae. Algae were exposed to standardized solutions with or without these DOM samples, each exposed at equal DOM concentrations and at equal non-toxic Cd(2+) activity (∼4 nM) that was buffered with a resin. The DOM increased total dissolved Cd by factors 3-16 due to complexation reactions at equal Cd(2+) activity. In contrast, the Cd uptake was unaffected by DOM or increased maximally 1.6 fold ((13)C enriched DOM). The (13)C analysis revealed that maximally 6% of algal C was derived from DOM and that this can explain the small increase in biomass Cd. It is concluded that free Cd(2+) and not DOM-complexed Cd is the main bioavailable form of Cd when solution Cd(2+) is well buffered. PMID:24874007

  5. Buffer Therapy for Cancer

    PubMed Central

    Ribeiro, Maria de Lourdes C; Silva, Ariosto S.; Bailey, Kate M.; Kumar, Nagi B.; Sellers, Thomas A.; Gatenby, Robert A.; Ibrahim-Hashim, Arig; Gillies, Robert J.

    2013-01-01

    Oral administration of pH buffers can reduce the development of spontaneous and experimental metastases in mice, and has been proposed in clinical trials. Effectiveness of buffer therapy is likely to be affected by diet, which could contribute or interfere with the therapeutic alkalinizing effect. Little data on food pH buffering capacity was available. This study evaluated the pH and buffering capacity of different foods to guide prospective trials and test the effect of the same buffer (lysine) at two different ionization states. Food groups were derived from the Harvard Food Frequency Questionnaire. Foods were blended and pH titrated with acid from initial pH values until 4.0 to determine “buffering score”, in mmol H+/pH unit. A “buffering score” was derived as the mEq H+ consumed per serving size to lower from initial to a pH 4.0, the postprandial pH of the distal duodenum. To differentiate buffering effect from any metabolic byproduct effects, we compared the effects of oral lysine buffers prepared at either pH 10.0 or 8.4, which contain 2 and 1 free base amines, respectively. The effect of these on experimental metastases formation in mice following tail vein injection of PC-3M prostate cancer cells were monitored with in vivo bioluminescence. Carbohydrates and dairy products’ buffering score varied between 0.5 and 19. Fruits and vegetables showed a low to zero buffering score. The score of meats varied between 6 and 22. Wine and juices had negative scores. Among supplements, sodium bicarbonate and Tums® had the highest buffering capacities, with scores of 11 and 20 per serving size, respectively. The “de-buffered” lysine had a less pronounced effect of prevention of metastases compared to lysine at pH 10. This study has demonstrated the anti-cancer effects of buffer therapy and suggests foods that can contribute to or compete with this approach to manage cancer. PMID:24371544

  6. RNA extraction from various recalcitrant plant tissues with a cethyltrimethylammonium bromide-containing buffer followed by an acid guanidium thiocyanate-phenol-chloroform treatment.

    PubMed

    Suzuki, Yuji; Mae, Tadahiko; Makino, Amane

    2008-07-01

    High-quality total RNA was extracted using a cethyltrimethylammonium bromide-containing buffer followed by an acid guanidium thiocyanate-phenol-chloroform treatment from recalcitrant plant tissues such as tree leaves (pine, Norway spruce, ginkgo, Japanese cedar, rose), flowers (rose, Lotus japonicus) and storage tissues (seeds of Lotus japonicus and rice, sweet potato tuber, banana fruit). This protocol greatly reduced the time required for RNA extraction.

  7. Rapid treatment of mild acne with a novel skin care system containing 1% salicylic acid, 10% buffered glycolic acid, and botanical ingredients.

    PubMed

    Bhatia, Ashish C; Jimenez, Felipe

    2014-06-01

    The biggest hurdle in the treatment of acne vulgaris is patient non-compliance that is due in large part to poor tolerability to common acne medications. As such, new acne treatments must be developed that balance good anti-acne efficacy with excellent tolerability in order to ensure patient adherence and by extension ensure good clinical outcomes. The goal of the present study was to determine the tolerability and efficacy of a novel skin care system, composed of a cleanser, containing 1% salicylic acid and botanical ingredients, and a treatment gel, containing 1% salicylic acid, 10% buffered glycolic acid and botanical ingredients for the treatment of mild acne. In this single-center, open-label clinical study, 25 male and female volunteers used the test cleanser and test gel twice daily over six weeks. Tolerability assessments showed that the skin care regimen was very well tolerated by all study volunteers. Acne severity was significantly reduced by two acne grades at six weeks. Inflammatory lesion counts were significantly reduced, on average, by 59.06% (P ≤ 0.0001), 91.62% (P ≤ 0.0001), 90.85% (P ≤ 0.0001) and by 98.55% (P ≤ 0.0001) at weeks 1, 2, 4, and 6, respectively. Non-inflammatory lesion counts were reduced, on average, by 13.54% (ns), 38.95% (P ≤ 0.0001), 44.48% (P ≤ 0.0001), and by 56.10% (P ≤ 0.0001) at weeks 1, 2, 4, and 6, respectively. Standardized photography also demonstrated a progressive reduction in acne lesions over time. In conclusion, results of the present study suggest that the tested skin care regimen offers rapid acne clearance and excellent tolerability that together may help to improve patient adherence as well as treatment outcome.

  8. Methanol Uptake by Low Temperature Aqueous Sulfuric Acid Solutions

    NASA Technical Reports Server (NTRS)

    Iraci, L. T.; Essin, A. M.; Golden, D. M.; Hipskind, R. Stephen (Technical Monitor)

    2001-01-01

    The global methanol budget is currently unbalanced, with source terms significantly larger than the sinks terms. To evaluate possible losses of gaseous methanol to sulfate aerosols, the solubility and reactivity of methanol in aqueous sulfuric acid solutions representative of upper tropospheric and lower stratospheric aerosols is under investigation. Methanol will partition into sulfate aerosols according to its Henry's law solubility. Using standard uptake techniques in a Knudsen cell reactor, we have measured the effective Henry's law coefficient, H*, for cold (196 - 220 K) solutions ranging between 45 and 70 wt % H2SO4. We have found that methanol solubility ranges from approx. 10(exp 5) - 10(exp 7) M/atm for UT/LS conditions. Solubility increases with decreasing temperature and with increasing sulfuric acid content. Although methanol is slightly more soluble than are acetone and formaldehyde, current data indicate that uptake by clean aqueous sulfuric acid particles will not be a significant sink for methanol in the UT/LS. These solubility measurements include uptake due to physical solvation and any rapid equilibria which are established in solution. Reaction between primary alcohols and sulfuric acid does occur, leading to the production of alkyl sulfates. Literature values for the rate of this reaction suggest that formation of CH3OSO3H is not significant over our experimental time scale for solutions below 80 wt % H2SO4. To confirm this directly, results obtained using a complementary equilibrium measurement technique will also be presented.

  9. Quantitative rRNA-targeted solution-based hybridization assay using peptide nucleic acid molecular beacons.

    PubMed

    Li, Xu; Morgenroth, Eberhard; Raskin, Lutgarde

    2008-12-01

    The potential of a solution-based hybridization assay using peptide nucleic acid (PNA) molecular beacon (MB) probes to quantify 16S rRNA of specific populations in RNA extracts of environmental samples was evaluated by designing PNA MB probes for the genera Dechloromonas and Dechlorosoma. In a kinetic study with 16S rRNA from pure cultures, the hybridization of PNA MB to target 16S rRNA exhibited a higher final hybridization signal and a lower apparent rate constant than the hybridizations to nontarget 16S rRNAs. A concentration of 10 mM NaCl in the hybridization buffer was found to be optimal for maximizing the difference between final hybridization signals from target and nontarget 16S rRNAs. Hybridization temperatures and formamide concentrations in hybridization buffers were optimized to minimize signals from hybridizations of PNA MB to nontarget 16S rRNAs. The detection limit of the PNA MB hybridization assay was determined to be 1.6 nM of 16S rRNA. To establish proof for the application of PNA MB hybridization assays in complex systems, target 16S rRNA from Dechlorosoma suillum was spiked at different levels to RNA isolated from an environmental (bioreactor) sample, and the PNA MB assay enabled effective quantification of the D. suillum RNA in this complex mixture. For another environmental sample, the quantitative results from the PNA MB hybridization assay were compared with those from clone libraries.

  10. Transbuccal delivery of 5-aza-2 -deoxycytidine: effects of drug concentration, buffer solution, and bile salts on permeation.

    PubMed

    Mahalingam, Ravichandran; Ravivarapu, Harish; Redkar, Sanjeev; Li, Xiaoling; Jasti, Bhaskara R

    2007-07-13

    Delivery of 5-aza-2 -deoxycytidine (decitabine) across porcine buccal mucosa was evaluated as an alternative to the complex intravenous infusion regimen currently used to administer the drug. A reproducible high-performance liquid chromatography method was developed and optimized for the quantitative determination of this drug. Decitabine showed a concentration-dependent passive diffusion process across porcine buccal mucosa. An increase in the ionic strength of the phosphate buffer from 100 to 400 mM decreased the flux from 3.57 +/- 0.65 to 1.89 +/- 0.61 microg/h/cm2. Trihydroxy bile salts significantly enhanced the flux of decitabine at a 100 mM concentration (P > .05). The steady-state flux of decitabine in the presence of 100 mM of sodium taurocholate and sodium glycocholate was 52.65 +/- 9.48 and 85.22 +/- 7.61 microg/cm2/h, respectively. Two dihydroxy bile salts, sodium deoxytaurocholate and sodium deoxyglycocholate, showed better enhancement effect than did trihydroxy bile salts. A 38-fold enhancement in flux was achieved with 10 mM of sodium deoxyglycocholate.

  11. Solid phase extraction of proteins from buffer solutions employing capillary-channeled polymer (C-CP) fibers as the stationary phase.

    PubMed

    Burdette, Carolyn Q; Marcus, R Kenneth

    2013-02-21

    Polypropylene (PP) capillary-channeled polymer (C-CP) fibers are applied for solid phase extraction (SPE) of proteins from aqueous buffer solutions using a micropipette tip-based format. A process was developed in which centrifugation is used as the moving force for solution passage in the loading/washing steps instead of the previously employed manual aspiration. The complete procedure requires ~15 minutes, with the number of samples run in parallel limited only by the capacity of the centrifuge. The method performance was evaluated based on adsorption and elution characteristics of several proteins (cytochrome c, lysozyme, myoglobin, and glucose oxidase) from 150 mM phosphate buffered saline (PBS) solutions. Protein concentration ranges of ~2 to 100 μg mL(-1) were employed and the recovery characteristics determined through UV-Vis absorbance spectrophotometry for protein quantification. The protein loading capacities across the range of proteins was ~1.5 μg for the 5 mg fiber tips. Average recoveries from PBS were determined for each protein sample; cytochrome c ~86%, lysozyme ~80%, myoglobin ~86%, and glucose oxidase ~89%. Recoveries from more complex matrices, synthetic urine and synthetic saliva, were determined to be ~90%. A 10× dilution study for a fixed 1 μg protein application yielded 94 ± 3.2% recoveries. The C-CP tips provided significantly higher recoveries for myoglobin in a 150 mM PBS matrix in comparison to a commercially available protein SPE product, with the added advantages of low cost, rapid processing, and reusability.

  12. Explaining the Spatial Variability in Stream Acid Buffering Chemistry and Aquatic Biota in the Neversink River Watershed, Catskill Mountains, New York State

    NASA Astrophysics Data System (ADS)

    Harpold, A. A.; Walter, M. T.

    2009-12-01

    The Neversink River Watershed (NRW) originates at the highest point in the Catskill Mountains and is sensitive to changing patterns in acidic deposition, precipitation, and air temperature. Despite reductions in fossil fuel emission since the Clean Air Act, past acidic deposition has accelerated the leaching of cations from the soil and reduced the stores of base cations necessary for buffering stream acidity. The goal of this study was to investigate connections between different watershed ‘features’ and the apparently complex spatial patterns of stream buffering chemistry (specifically, acid neutralizing capacity ANC and Ca concentrations) and aquatic biota (macroinvertebrate and fish populations). The ten nested NRW watersheds (2.0 km^2 to 176.0 km^2) have relatively homogeneous bedrock geology, forested cover, and soil series; therefore, we hypothesized that differing distributions of hydrological flowpaths between the watersheds control the variability in stream buffering chemistry and aquatic biota. However because the flowpath distributions are not directly measurable, this study used step-wise linear regression to develop relationships between watershed ‘features’ and buffering chemistry. The regression results showed that the mean ratio of precipitation to stream runoff (or runoff ratio) from twenty non-winter storm events explained more than 81% of the variability in mean summer ANC and Ca concentrations. The results also suggested that steeper (higher mean slope) more channelized watersheds (larger drainage density) are more susceptible to stream acidity and negative impacts on biota. A simple linear relationship (using no discharge or water chemistry measurements) was able to explain buffering chemistry and aquatic biota populations in 17 additional NRW watersheds (0.3 km^2 to 160.0 km^2), including 60-80% of the variability in macroinvertebrate populations (EPT richness and BAP) and 50-60% of the variability in fish density and species richness

  13. Free flow cell electrophoresis using zwitterionic buffer

    NASA Technical Reports Server (NTRS)

    Rodkey, R. Scott

    1990-01-01

    Studies of a zwitterionic buffer formulated for cell electrophoresis were done using the McDonnell-Douglas Continuous Flow Electrophoresis System. Standard buffers were analyzed for their stability in the electrical field and the results showed that both buffers tested were inherently unstable. Further, titration studies showed that the standards buffers buffered poorly at the pH employed for electrophoresis. The zwitterionic buffer buffered well at its nominal pH and was shown to be stable in the electrical field. Comparative studies of the buffer with standard cell separation buffers using formalin fixed rabbit and goose red blood cells showed that the zwitterionic buffer gave better resolution of the fixed cells. Studies with viable hybridoma cells showed that buffer Q supported cell viability equal to Hank's Balanced Salt Solution and that hybridoma cells in different stages of the growth cycle demonstrated reproducible differences in electrophoretic mobility.

  14. Buffer Biology.

    ERIC Educational Resources Information Center

    Morgan, Kelly

    2000-01-01

    Presents a science experiment in which students test the buffering capacity of household products such as shampoo, hand lotion, fizzies candy, and cola. Lists the standards addressed in this experiment and gives an example of a student lab write-up. (YDS)

  15. Degradation of berenil (diminazene aceturate) in acidic aqueous solution.

    PubMed

    Campbell, Michael; Prankerd, Richard J; Davie, Ashley S; Charman, William N

    2004-10-01

    The trypanocide berenil was assessed for chemical stability over the pH range 1-8 at 37 degrees C and 0.2 M ionic strength. It was found to be sufficiently unstable under acid conditions that its therapeutic efficacy is most likely severely compromised when administered orally. At pH 3, the half-life was 35 min, decreasing to 1.5 min at pH 1.75. Reaction rate constants were corrected for the effects of buffer catalysis and were found to range from 2.00 min(-1) at pH 1 to 6.1 x 10(-6) min(-1) at pH 8. The pH-rate profile displayed a region (pH 1-4) where specific acid catalysis was dominant, followed by a transitional region (pH 5-7), and finally a region (pH >7) where uncatalysed degradation was most important. It is recommended that berenil be enteric coated for formulations to be used in treating Third World parasitic diseases. PMID:15482649

  16. Evaporation kinetics of acetic acid-water solutions

    NASA Astrophysics Data System (ADS)

    Duffey, K.; Wong, N.; Saykally, R.; Cohen, R. C.

    2012-12-01

    The transport of water molecules across vapor-liquid interfaces in the atmosphere is a crucial step in the formation and evolution of cloud droplets. Despite decades of study, the effects of solutes on the mechanism and rate of evaporation and condensation remain poorly characterized. The present work aims to determine the effect of atmospherically-relevant solutes on the evaporation rate of water. In our experiments, we create a train of micron-sized droplets and measure their temperature via Raman thermometry as they undergo evaporation without condensation. Analysis of the cooling rate yields the evaporation coefficient (γ). Previous work has shown that inorganic salts have little effect on γ, with surface-adsorbing anions causing a slight reduction in the coefficient from that measured for pure water. Organic acids are ubiquitous in aqueous aerosol and have been shown to disrupt the surface structure of water. Here we describe measurements of the evaporation rate of acetic acid solutions, showing that acetic acid reduces γ to a larger extent than inorganic ions, and that γ decreases with increasing acetic acid concentration.

  17. Iron buffer system in the water column and partitioning in the sediments of the naturally acidic Lake Caviahue, Neuquén, Argentina

    NASA Astrophysics Data System (ADS)

    Cabrera, J. M.; Diaz, M. M.; Schultz, S.; Temporetti, P.; Pedrozo, F.

    2016-05-01

    Sedimentary iron partitioning was studied for five sediment strata (16 cm depth) at three sampling sites of the naturally-occurring acidic Lake Caviahue (Patagonia, Argentina). Additionally, water column iron was modeled based on five-year period input loadings to study a possible iron buffer system. The partition coefficient between the water column and the total iron content of the sediments was also addressed. Sedimentary iron was found to be distributed, on average, in the following forms: exchangeable (6%), iron oxides (4%), pyrite and reactive organic matter (38%) and residual (non-andesitic) materials with a high content of humic acids (52%). Furthermore, we found that the dissolved iron in the lake was nearly constant throughout the five year period we studied. This is consistent with the existence of an iron buffer system in the lake at pH between 2.0 and 3.0, which may cause differential iron precipitation at the delta of the volcanic river with respect to the deeper northern and southern arms. Sedimentary iron measurements taken at the delta further support the existence of a buffer system, where it was found that the iron content in the sub-superficial stratum (2 cm) was double that of the remainder of the vertical profile at the same site.

  18. The effects of secular calcium and magnesium concentration changes on the thermodynamics of seawater acid/base chemistry: Implications for Eocene and Cretaceous ocean carbon chemistry and buffering

    NASA Astrophysics Data System (ADS)

    Hain, Mathis P.; Sigman, Daniel M.; Higgins, John A.; Haug, Gerald H.

    2015-05-01

    Reconstructed changes in seawater calcium and magnesium concentration ([Ca2+], [Mg2+]) predictably affect the ocean's acid/base and carbon chemistry. Yet inaccurate formulations of chemical equilibrium "constants" are currently in use to account for these changes. Here we develop an efficient implementation of the MIAMI Ionic Interaction Model to predict all chemical equilibrium constants required for carbon chemistry calculations under variable [Ca2+] and [Mg2+]. We investigate the impact of [Ca2+] and [Mg2+] on the relationships among the ocean's pH, CO2, dissolved inorganic carbon (DIC), saturation state of CaCO3 (Ω), and buffer capacity. Increasing [Ca2+] and/or [Mg2+] enhances "ion pairing," which increases seawater buffering by increasing the concentration ratio of total to "free" (uncomplexed) carbonate ion. An increase in [Ca2+], however, also causes a decline in carbonate ion to maintain a given Ω, thereby overwhelming the ion pairing effect and decreasing seawater buffering. Given the reconstructions of Eocene [Ca2+] and [Mg2+] ([Ca2+]~20 mM; [Mg2+]~30 mM), Eocene seawater would have required essentially the same DIC as today to simultaneously explain a similar-to-modern Ω and the estimated Eocene atmospheric CO2 of ~1000 ppm. During the Cretaceous, at ~4 times modern [Ca2+], ocean buffering would have been at a minimum. Overall, during times of high seawater [Ca2+], CaCO3 saturation, pH, and atmospheric CO2 were more susceptible to perturbations of the global carbon cycle. For example, given both Eocene and Cretaceous seawater [Ca2+] and [Mg2+], a doubling of atmospheric CO2 would require less carbon addition to the ocean/atmosphere system than under modern seawater composition. Moreover, increasing seawater buffering since the Cretaceous may have been a driver of evolution by raising energetic demands of biologically controlled calcification and CO2 concentration mechanisms that aid photosynthesis.

  19. Solution influence on biomolecular equilibria - Nucleic acid base associations

    NASA Technical Reports Server (NTRS)

    Pohorille, A.; Pratt, L. R.; Burt, S. K.; Macelroy, R. D.

    1984-01-01

    Various attempts to construct an understanding of the influence of solution environment on biomolecular equilibria at the molecular level using computer simulation are discussed. First, the application of the formal statistical thermodynamic program for investigating biomolecular equilibria in solution is presented, addressing modeling and conceptual simplications such as perturbative methods, long-range interaction approximations, surface thermodynamics, and hydration shell. Then, Monte Carlo calculations on the associations of nucleic acid bases in both polar and nonpolar solvents such as water and carbon tetrachloride are carried out. The solvent contribution to the enthalpy of base association is positive (destabilizing) in both polar and nonpolar solvents while negative enthalpies for stacked complexes are obtained only when the solute-solute in vacuo energy is added to the total energy. The release upon association of solvent molecules from the first hydration layer around a solute to the bulk is accompanied by an increase in solute-solvent energy and decrease in solvent-solvent energy. The techniques presented are expectd to displace less molecular and more heuristic modeling of biomolecular equilibria in solution.

  20. Effect of temperature and solvent composition on acid dissociation equilibria, I: Sequenced (s)(s)pKa determination of compounds commonly used as buffers in high performance liquid chromatography coupled to mass spectroscopy detection.

    PubMed

    Padró, Juan M; Acquaviva, Agustín; Tascon, Marcos; Gagliardi, Leonardo G; Castells, Cecilia B

    2012-05-01

    A new automated and rapid potentiometric method for determining the effect of organic-solvent composition on pK(a) has been developed. It is based on the measurements of pH values of buffer solutions of variable solvent compositions using a combined glass electrode. Additions of small volumes of one precisely thermostated solution into another, both containing exactly the same analytical concentrations of the buffer components, can produce continuous changes in the solvent composition. Two sequences of potential measurements, one of increasing and the other of decreasing solvent content, are sufficient to obtain the pK(a) values of the acidic compound within the complete solvent-composition range in about 2h. The experimental design, procedures, and calculations needed to convert the measured pH into the thermodynamic pK(a) values are thoroughly discussed. This rapid and automated method allows the systematic study of the effect of solvent compositions and temperatures on the pK(a). It has been applied to study the dissociation constants of two monoprotic acids: formic acid and triethylamine:HCl in acetonitrile/water mixtures within the range from 0 to 90% (v/v) at temperatures between 20°C and 60°C. These volatile compounds are frequently used to control the pH of the mobile phase in HPLC, especially in methods coupled to mass-spectrometry detection. The obtained pK(a) values are in excellent agreement with those previously reported. The results were fitted to empirical functions between pK(a) and temperature and composition. These equations, which can be used to estimate the pK(a) of these substances at any composition and temperature, would be highly useful in practical work during chromatographic method development.

  1. Method for extracting lanthanides and actinides from acid solutions

    DOEpatents

    Horwitz, E. Philip; Kalina, Dale G.; Kaplan, Louis; Mason, George W.

    1985-01-01

    A process for the recovery of actinide and lanthanide values from aqueous acidic solutions with an organic extractant having the formula: ##STR1## where .phi. is phenyl, R.sup.1 is a straight or branched alkyl or alkoxyalkyl containing from 6 to 12 carbon atoms and R.sup.2 is an alkyl containing from 3 to 6 carbon atoms. The process is suitable for the separation of actinide and lanthanide values from fission product values found together in high level nuclear reprocessing waste solutions.

  2. DC diaphragm discharge in water solutions of selected organic acids

    NASA Astrophysics Data System (ADS)

    Vyhnankova, Edita J.; Hammer, Malte U.; Reuter, Stephan; Krcma, Frantisek

    2015-07-01

    Effect of four simple organic acids water solution on a DC diaphragm discharge was studied. Efficiency of the discharge was quantified by the hydrogen peroxide production determined by UV-VIS spectrometry of a H2O2 complex formed with specific titanium reagent. Automatic titration was used to study the pH behaviour after the plasma treatment. Optical emission spectroscopy overview spectra were recorded and detailed spectra of OH band and Hβ line were used to calculate the rotational temperature and comparison of the line profile (reflecting electron concentration) in the acid solutions. Contribution to the topical issue "The 14th International Symposium on High Pressure Low Temperature Plasma Chemistry (HAKONE XIV)", edited by Nicolas Gherardi, Ronny Brandenburg and Lars Stollenwark

  3. Interaction of Ethyl Alcohol Vapor with Sulfuric Acid Solutions

    NASA Technical Reports Server (NTRS)

    Leu, Ming-Taun

    2006-01-01

    We investigated the uptake of ethyl alcohol (ethanol) vapor by sulfuric acid solutions over the range approx.40 to approx.80 wt % H2SO4 and temperatures of 193-273 K. Laboratory studies used a fast flow-tube reactor coupled to an electron-impact ionization mass spectrometer for detection of ethanol and reaction products. The uptake coefficients ((gamma)) were measured and found to vary from 0.019 to 0.072, depending upon the acid composition and temperature. At concentrations greater than approx.70 wt % and in dilute solutions colder than 220 K, the values approached approx.0.07. We also determined the effective solubility constant of ethanol in approx.40 wt % H2SO4 in the temperature range 203-223 K. The potential implications to the budget of ethanol in the global troposphere are briefly discussed.

  4. Effects of intravenous solutions on acid-base equilibrium: from crystalloids to colloids and blood components.

    PubMed

    Langer, Thomas; Ferrari, Michele; Zazzeron, Luca; Gattinoni, Luciano; Caironi, Pietro

    2014-01-01

    Intravenous fluid administration is a medical intervention performed worldwide on a daily basis. Nevertheless, only a few physicians are aware of the characteristics of intravenous fluids and their possible effects on plasma acid-base equilibrium. According to Stewart's theory, pH is independently regulated by three variables: partial pressure of carbon dioxide, strong ion difference (SID), and total amount of weak acids (ATOT). When fluids are infused, plasma SID and ATOT tend toward the SID and ATOT of the administered fluid. Depending on their composition, fluids can therefore lower, increase, or leave pH unchanged. As a general rule, crystalloids having a SID greater than plasma bicarbonate concentration (HCO₃-) cause an increase in plasma pH (alkalosis), those having a SID lower than HCO₃- cause a decrease in plasma pH (acidosis), while crystalloids with a SID equal to HCO₃- leave pH unchanged, regardless of the extent of the dilution. Colloids and blood components are composed of a crystalloid solution as solvent, and the abovementioned rules partially hold true also for these fluids. The scenario is however complicated by the possible presence of weak anions (albumin, phosphates and gelatins) and their effect on plasma pH. The present manuscript summarises the characteristics of crystalloids, colloids, buffer solutions and blood components and reviews their effect on acid-base equilibrium. Understanding the composition of intravenous fluids, along with the application of simple physicochemical rules best described by Stewart's approach, are pivotal steps to fully elucidate and predict alterations of plasma acid-base equilibrium induced by fluid therapy.

  5. Use of a molecular form technique for the penetration of supersaturated solutions of salicylic acid across silicone membranes and human skin in vitro.

    PubMed

    Leveque, N; Raghavan, S L; Lane, M E; Hadgraft, J

    2006-08-01

    Permeation enhancement of salicylic acid (SA) from supersaturated solutions formed using a 'molecular form' technique was investigated. In a conventional cosolvent technique, two solvents are used, one in which the drug is considerably more soluble than the other. Propylene glycol and water have been predominantly used as cosolvents to create supersaturation in skin permeation enhancement. In this paper, we report the use of buffer solutions with different pHs as media for producing different molecular forms. Supersaturated solutions were prepared using pH 8:pH 2 (80:20 v/v), which gave a nominal pH when mixed of around 5. Model silicone membranes and human skin were used. Hydroxypropyl methyl cellulose (HPMC) was employed to stabilise the supersaturated states. Stability data showed that while the SA supersaturated solutions without HPMC crystallised between 15 min and 46 h depending on the degree of supersaturation, the solutions with HPMC were stable for more than 2 months. The flux of SA increased with the degree of saturation for solutions prepared in a 80:20 buffer pH 8/buffer pH 2 mixture. Although the fluxes of SA with and without HPMC were similar both through silicone membrane and human skin, HPMC was found to be effective in increasing the stability of supersaturated solutions of SA.

  6. An ellipsometric study of mild steel in hydrochloric acid solutions

    NASA Astrophysics Data System (ADS)

    Brakenbury, W. R. E.; Grzeskowiak, R.

    1986-04-01

    An ellipsometric study has been made on mild steel in hydrochloric acid solutions, in a situation where film growth is not expected. The results are considered to be due to roughening and have been interpreted in terms of a Fenstermaker-McCrackin type roughening model. It appears that the ellipsometer is sensitive mainly to a small scale roughening consisting of etch pits of a few nanometers in dimensions rather than the larger roughened features easily seen by microscopic examination.

  7. Recovery of rhenium from sulfuric acid solutions with activated coals

    SciTech Connect

    Troshkina, I.D.; Naing, K.Z.; Ushanova, O.N.; P'o, V.; Abdusalomov, A.A.

    2006-09-15

    Equilibrium and kinetic characteristics of rhenium sorption from sulfuric acid solutions (pH 2) by activated coals produced from coal raw materials (China) were studied. Constants of the Henry equation describing isotherms of rhenium sorption by activated coals were calculated. The effective diffusion coefficients of rhenium in the coals were determined. The dynamic characteristics of rhenium sorption and desorption were determined for the activated coal with the best capacity and kinetic characteristics.

  8. Chromatography of alkaline earths and transition metals on tin(iv) arsenosilicate and arsenophosphate thin layers in buffered EDTA solutions

    SciTech Connect

    Varshney, K.G.; Anwar, S.; Khan, A.A.

    1985-01-01

    The complex forming ability of ethylene diamine tetraacetic acid at various pH values and the ion exchange behavior of tin(IV) arsenosilicate and arsenophosphate cation exchangers have been combined in a chromatographic study of some metal ions. As a result some interesting observations have been made, which have led to certain analytically difficult separations such as Ca/sup 2 +/ -Sr/sup 2 +/, Ca/sup 2 +/ -Ba/sup 2 +/ and Hg/sup 2 +/ from Cu/sup 2 +/, Ni/sup 2 +/, Zn/sup 2 +/, Co/sup 2 +/ and Mn/sup 2 +/.

  9. Peak shapes of acids and bases under overloaded conditions in reversed-phase liquid chromatography, with weakly buffered mobile phases of various pH: a thermodynamic interpretation.

    PubMed

    Gritti, Fabrice; Guiochon, Georges

    2009-01-01

    We measured overloaded band profiles for a series of nine compounds (phenol, caffeine, 3-phenyl 1-propanol, 2-phenylbutyric acid, amphetamine, aniline, benzylamine, p-toluidine, and procainamidium chloride) on columns packed with four different C(18)-bonded packing materials: XTerra-C(18), Gemini-C(18), Luna-C(18)(2), and Halo-C(18), using buffered methanol-water mobile phases. The pHWS of the mobile phase was increased from 2.6 to 11.3. The buffer concentration (either phosphate, acetate, or carbonate buffers) was set constant at values below the maximum concentration of the sample in the band. The influence of the surface chemistry of the packing material on the retention and the shape of the peaks was investigated. Adsorbents having a hybrid inorganic/organic structure tend to give peaks exhibiting moderate or little tailing. The retention and the shape of the band profiles can easily be interpreted at pHsWS that are well above or well below the pKWS(a) of the compound studied. In contrast, the peak shapes in the intermediary pH range (i.e., close to the compound pKWS(a)) have rarely been studied. These shapes reveal the complexity of the competitive adsorption behavior of couples of acido-basic conjugated compounds at pHsWS that are close to their pKWS(a). They also reveal the role of the buffer capacity on the resulting peak shape. With increasing pHWS, the overloaded profiles are first langmuirian (isotherm type I) at low pHsWS, they become S-shaped (isotherm type II), then anti-langmuirian (isotherm type III), S-shaped again at intermediate pHsWS, and finally return to a langmuirian shape at high pHsWS. A new general adsorption isotherm model that takes into account the dissociation equilibrium of conjugated acidic and basic species in the bulk mobile phase accounts for these transient band shapes. An excellent agreement was achieved between experimental profiles and those calculated with a two-sites adsorption isotherm model at all pHsWS. The neutral

  10. Methanol Uptake By Low Temperature Aqueous Sulfuric Acid Solutions

    NASA Technical Reports Server (NTRS)

    Iraci, Laura T.; Essin, Andrew M.; Golden, David M.; Hipskind, R. Stephen (Technical Monitor)

    2001-01-01

    To evaluate the role of upper tropospheric and lower stratospheric aerosols in the global budget of methanol, the solubility and reactivity of CH3OH in aqueous sulfuric acid solutions are under investigation. Using standard uptake techniques in a Knudsen cell reactor, we have measured the effective Henry's law coefficient, H(*), for methanol dissolution into 45 to 70 percent by weight H2SO4. We find that methanol solubility ranges from 10(exp 5) to 10(exp 8) M/atm and increases with decreasing temperature and with increasing sulfuric acid content. These solubility measurements include uptake due to physical solvation and all rapid equilibria which are established in solution. Our data indicate that simple uptake by aqueous sulfuric acid particles will not be a significant sink for methanol in the UT/LS. These results differ from those recently reported in the literature, and an explanation of this disparity will be presented. In addition to solvation, reaction between primary alcohols and sulfuric acid does occur, leading to the production of alkyl sulfates. Literature values for the rate of this reaction suggest that formation of CH3OSO3H may proceed in the atmosphere but is not significant under our experimental conditions. Results obtained using a complementary equilibrium measurement technique confirm this directly. In addition, the extent of methanol sequestration via formation of mono- and dimethylsulfate will be evaluated under several atmospheric conditions.

  11. Complexation of buffer constituents with neutral complexation agents: part I. Impact on common buffer properties.

    PubMed

    Riesová, Martina; Svobodová, Jana; Tošner, Zdeněk; Beneš, Martin; Tesařová, Eva; Gaš, Bohuslav

    2013-09-17

    The complexation of buffer constituents with the complexation agent present in the solution can very significantly influence the buffer properties, such as pH, ionic strength, or conductivity. These parameters are often crucial for selection of the separation conditions in capillary electrophoresis or high-pressure liquid chromatography (HPLC) and can significantly affect results of separation, particularly for capillary electrophoresis as shown in Part II of this paper series (Beneš, M.; Riesová, M.; Svobodová, J.; Tesařová, E.; Dubský, P.; Gaš, B. Anal. Chem. 2013, DOI: 10.1021/ac401381d). In this paper, the impact of complexation of buffer constituents with a neutral complexation agent is demonstrated theoretically as well as experimentally for the model buffer system composed of benzoic acid/LiOH or common buffers (e.g., CHES/LiOH, TAPS/LiOH, Tricine/LiOH, MOPS/LiOH, MES/LiOH, and acetic acid/LiOH). Cyclodextrins as common chiral selectors were used as model complexation agents. We were not only able to demonstrate substantial changes of pH but also to predict the general complexation characteristics of selected compounds. Because of the zwitterion character of the common buffer constituents, their charged forms complex stronger with cyclodextrins than the neutral ones do. This was fully proven by NMR measurements. Additionally complexation constants of both forms of selected compounds were determined by NMR and affinity capillary electrophoresis with a very good agreement of obtained values. These data were advantageously used for the theoretical descriptions of variations in pH, depending on the composition and concentration of the buffer. Theoretical predictions were shown to be a useful tool for deriving some general rules and laws for complexing systems.

  12. Complexation of buffer constituents with neutral complexation agents: part I. Impact on common buffer properties.

    PubMed

    Riesová, Martina; Svobodová, Jana; Tošner, Zdeněk; Beneš, Martin; Tesařová, Eva; Gaš, Bohuslav

    2013-09-17

    The complexation of buffer constituents with the complexation agent present in the solution can very significantly influence the buffer properties, such as pH, ionic strength, or conductivity. These parameters are often crucial for selection of the separation conditions in capillary electrophoresis or high-pressure liquid chromatography (HPLC) and can significantly affect results of separation, particularly for capillary electrophoresis as shown in Part II of this paper series (Beneš, M.; Riesová, M.; Svobodová, J.; Tesařová, E.; Dubský, P.; Gaš, B. Anal. Chem. 2013, DOI: 10.1021/ac401381d). In this paper, the impact of complexation of buffer constituents with a neutral complexation agent is demonstrated theoretically as well as experimentally for the model buffer system composed of benzoic acid/LiOH or common buffers (e.g., CHES/LiOH, TAPS/LiOH, Tricine/LiOH, MOPS/LiOH, MES/LiOH, and acetic acid/LiOH). Cyclodextrins as common chiral selectors were used as model complexation agents. We were not only able to demonstrate substantial changes of pH but also to predict the general complexation characteristics of selected compounds. Because of the zwitterion character of the common buffer constituents, their charged forms complex stronger with cyclodextrins than the neutral ones do. This was fully proven by NMR measurements. Additionally complexation constants of both forms of selected compounds were determined by NMR and affinity capillary electrophoresis with a very good agreement of obtained values. These data were advantageously used for the theoretical descriptions of variations in pH, depending on the composition and concentration of the buffer. Theoretical predictions were shown to be a useful tool for deriving some general rules and laws for complexing systems. PMID:23889602

  13. Sustainable Soil Washing: Shredded Card Filtration of Potentially Toxic Elements after Leaching from Soil Using Organic Acid Solutions.

    PubMed

    Ash, Christopher; Drábek, Ondřej; Tejnecký, Václav; Jehlička, Jan; Michon, Ninon; Borůvka, Luboš

    2016-01-01

    Shredded card (SC) was assessed for use as a sorbent of potentially toxic elements (PTE) carried from contaminated soil in various leachates (oxalic acid, formic acid, CaCl2, water). We further assessed SC for retention of PTE, using acidified water (pH 3.4). Vertical columns and a peristaltic pump were used to leach PTE from soils (O and A/B horizons) before passing through SC. Sorption onto SC was studied by comparing leachates, and by monitoring total PTE contents on SC before and after leaching. SC buffers against acidic soil conditions that promote metals solubility; considerable increases in solution pH (+4.49) were observed. Greatest differences in solution PTE content after leaching with/without SC occurred for Pb. In oxalic acid, As, Cd, Pb showed a high level of sorption (25, 15, and 58x more of the respective PTE in leachates without SC). In formic acid, Pb sorption was highly efficient (219x more Pb in leachate without SC). In water, only Pb showed high sorption (191x more Pb in leachate without SC). In desorption experiments, release of PTE from SC varied according to the source of PTE (organic/mineral soil), and type of solvent used. Arsenic was the PTE most readily leached in desorption experiments. Low As sorption from water was followed by fast release (70% As released from SC). A high rate of Cd sorption from organic acid solutions was followed by strong retention (~12% Cd desorption). SC also retained Pb after sorption from water, with subsequent losses of ≤8.5% of total bound Pb. The proposed use of this material is for the filtration of PTE from extract solution following soil washing. Low-molecular-mass organic acids offer a less destructive, biodegradable alternative to strong inorganic acids for soil washing.

  14. Sustainable Soil Washing: Shredded Card Filtration of Potentially Toxic Elements after Leaching from Soil Using Organic Acid Solutions.

    PubMed

    Ash, Christopher; Drábek, Ondřej; Tejnecký, Václav; Jehlička, Jan; Michon, Ninon; Borůvka, Luboš

    2016-01-01

    Shredded card (SC) was assessed for use as a sorbent of potentially toxic elements (PTE) carried from contaminated soil in various leachates (oxalic acid, formic acid, CaCl2, water). We further assessed SC for retention of PTE, using acidified water (pH 3.4). Vertical columns and a peristaltic pump were used to leach PTE from soils (O and A/B horizons) before passing through SC. Sorption onto SC was studied by comparing leachates, and by monitoring total PTE contents on SC before and after leaching. SC buffers against acidic soil conditions that promote metals solubility; considerable increases in solution pH (+4.49) were observed. Greatest differences in solution PTE content after leaching with/without SC occurred for Pb. In oxalic acid, As, Cd, Pb showed a high level of sorption (25, 15, and 58x more of the respective PTE in leachates without SC). In formic acid, Pb sorption was highly efficient (219x more Pb in leachate without SC). In water, only Pb showed high sorption (191x more Pb in leachate without SC). In desorption experiments, release of PTE from SC varied according to the source of PTE (organic/mineral soil), and type of solvent used. Arsenic was the PTE most readily leached in desorption experiments. Low As sorption from water was followed by fast release (70% As released from SC). A high rate of Cd sorption from organic acid solutions was followed by strong retention (~12% Cd desorption). SC also retained Pb after sorption from water, with subsequent losses of ≤8.5% of total bound Pb. The proposed use of this material is for the filtration of PTE from extract solution following soil washing. Low-molecular-mass organic acids offer a less destructive, biodegradable alternative to strong inorganic acids for soil washing. PMID:26900684

  15. Sustainable Soil Washing: Shredded Card Filtration of Potentially Toxic Elements after Leaching from Soil Using Organic Acid Solutions

    PubMed Central

    Ash, Christopher; Drábek, Ondřej; Tejnecký, Václav; Jehlička, Jan; Michon, Ninon; Borůvka, Luboš

    2016-01-01

    Shredded card (SC) was assessed for use as a sorbent of potentially toxic elements (PTE) carried from contaminated soil in various leachates (oxalic acid, formic acid, CaCl2, water). We further assessed SC for retention of PTE, using acidified water (pH 3.4). Vertical columns and a peristaltic pump were used to leach PTE from soils (O and A/B horizons) before passing through SC. Sorption onto SC was studied by comparing leachates, and by monitoring total PTE contents on SC before and after leaching. SC buffers against acidic soil conditions that promote metals solubility; considerable increases in solution pH (+4.49) were observed. Greatest differences in solution PTE content after leaching with/without SC occurred for Pb. In oxalic acid, As, Cd, Pb showed a high level of sorption (25, 15, and 58x more of the respective PTE in leachates without SC). In formic acid, Pb sorption was highly efficient (219x more Pb in leachate without SC). In water, only Pb showed high sorption (191x more Pb in leachate without SC). In desorption experiments, release of PTE from SC varied according to the source of PTE (organic/mineral soil), and type of solvent used. Arsenic was the PTE most readily leached in desorption experiments. Low As sorption from water was followed by fast release (70% As released from SC). A high rate of Cd sorption from organic acid solutions was followed by strong retention (~12% Cd desorption). SC also retained Pb after sorption from water, with subsequent losses of ≤8.5% of total bound Pb. The proposed use of this material is for the filtration of PTE from extract solution following soil washing. Low-molecular-mass organic acids offer a less destructive, biodegradable alternative to strong inorganic acids for soil washing. PMID:26900684

  16. The appearance of Ti3+ states in solution-processed TiOx buffer layers in inverted organic photovoltaics

    NASA Astrophysics Data System (ADS)

    Zhidkov, Ivan S.; McLeod, John A.; Kurmaev, Ernst Z.; Korotin, Michael A.; Kukharenko, Andrey I.; Savva, Achilleas; Choulis, Stelios A.; Korotin, Danila M.; Cholakh, Seif O.

    2016-07-01

    We study the low-temperature solution processed TiOx films and device structures using core level and valence X-ray photoelectron spectroscopy (XPS) and electronic structure calculations. We are able to correlate the fraction of Ti3+ present as obtained from Ti 2p core level XPS with the intensity of the defect states that appear within the band gap as observed with our valence XPS. Constructing an operating inverted organic photovoltaic (OPV) using the TiOx film as an electron selective contact may increase the fraction of Ti3+ present. We provide evidence that the number of charge carriers in TiOx can be significantly varied and this might influence the performance of inverted OPVs.

  17. CdS and Cd-Free Buffer Layers on Solution Phase Grown Cu2ZnSn(SxSe1- x)4 :Band Alignments and Electronic Structure Determined with Femtosecond Ultraviolet Photoemission Spectroscopy

    SciTech Connect

    Haight, Richard; Barkhouse, Aaron; Wang, Wei; Yu, Luo; Shao, Xiaoyan; Mitzi, David; Hiroi, Homare; Sugimoto, Hiroki

    2013-12-02

    The heterojunctions formed between solution phase grown Cu2ZnSn(SxSe1- x)4(CZTS,Se) and a number of important buffer materials including CdS, ZnS, ZnO, and In2S3, were studied using femtosecond ultraviolet photoemission spectroscopy (fs-UPS) and photovoltage spectroscopy. With this approach we extract the magnitude and direction of the CZTS,Se band bending, locate the Fermi level within the band gaps of absorber and buffer and measure the absorber/buffer band offsets under flatband conditions. We will also discuss two-color pump/probe experiments in which the band bending in the buffer layer can be independently determined. Finally, studies of the bare CZTS,Se surface will be discussed including our observation of mid-gap Fermi level pinning and its relation to Voc limitations and bulk defects.

  18. Toluene nitration in irradiated nitric acid and nitrite solution

    SciTech Connect

    Gracy Elias; Bruce J. Mincher; Stephen P. Mezyk; Jim Muller; Leigh R. Martin

    2011-04-01

    The kinetics, mechanisms, and stable products produced for the aryl alkyl mild ortho-para director - toluene, in irradiated nitric acid and neutral nitrite solutions were investigated using ?, and pulse radiolysis. Electron pulse radiolysis was used to determine the bimolecular rate constants for the reaction of toluene with different transient species produced by irradiation. HPLC with UV detection was primarily used to assess the stable reaction products. GC-MS and LC-MS were used to confirm the results from HPLC. Free-radical nitration reaction products were found in irradiated acidic and neutral media. In acidic medium, the ring substitution and side chain substitution and oxidation produced different nitro products. In ring substitution, nitrogen oxide radicals were added mainly to hydroxyl radical-produced cyclohexadienyl radical, and in side chain substitution they were added to the carbon-centered benzyl radical produced by H-atom abstraction. In neutral nitrite toluene solution, radiolytic ring nitration products approached a statistically random distribution, suggesting a free-radical reaction involving addition of the •NO2 radical.

  19. Effect of phytic acid, ethylenediaminetetraacetic acid, and chitosan solutions on microhardness of the human radicular dentin

    PubMed Central

    Nikhil, Vineeta; Jaiswal, Shikha; Bansal, Parul; Arora, Rohit; Raj, Shalya; Malhotra, Pulkit

    2016-01-01

    Aim: The purpose of this study was to evaluate the effect of phytic acid, ethylenediaminetetraacetic acid (EDTA), and chitosan solutions on the microhardness of human radicular dentin. Materials and Methods: Thirty dentin specimens were randomly divided into three groups of 10 specimens each according to the irrigant used: G1 — 1% phytic acid, G2 — 17% EDTA, and G3 — 0.2% chitosan. A standardized volume of each chelating solution was used for 3 min. Dentin microhardness was measured before and after application at the cervical, middle, and apical levels with a Vickers indenter under a 200-g load and a 10-s dwell time. The results were analyzed using one-way analysis of variance (ANOVA) and Student's t test. Results: Microhardness of the radicular dentin varied at the cervical, middle, and apical levels. EDTA had the greatest overall effect, causing a sharp percentage reduction in dentin microhardness with a significant difference from phytic acid and chitosan (P = 0.002). However, phytic acid and chitosan differed insignificantly from each other (P = 0.887). Conclusion: All tested chelating solutions reduced microhardness of the radicular dentin layer at all the levels. However, reduction was least at the apical level. EDTA caused more reduction in dentin microhardness than chitosan while phytic acid reduced the least. PMID:27099428

  20. High effective cytosolic H+ buffering in mouse cortical astrocytes attributable to fast bicarbonate transport.

    PubMed

    Theparambil, Shefeeq M; Deitmer, Joachim W

    2015-09-01

    Cytosolic H(+) buffering plays a major role for shaping intracellular H(+) shifts and hence for the availability of H(+) for biochemical reactions and acid/base-coupled transport processes. H(+) buffering is one of the prime means to protect the cell from large acid/base shifts. We have used the H(+) indicator dye BCECF and confocal microscopy to monitor the cytosolic H(+) concentration, [H(+)]i, in cultured cortical astrocytes of wild-type mice and of mice deficient in sodium/bicarbonate cotransporter NBCe1 (NBCe1-KO) or in carbonic anhydrase isoform II (CAII-KO). The steady-state buffer strength was calculated from the amplitude of [H(+)]i transients as evoked by CO2/HCO3(-) and by butyric acid in the presence and absence of CO2/HCO3(-). We tested the hypotheses if, in addition to instantaneous physicochemical H(+) buffering, rapid acid/base transport across the cell membrane contributes to the total, "effective" cytosolic H(+) buffering. In the presence of 5% CO2/26 mM HCO3(-), H(+) buffer strength in astrocytes was increased 4-6 fold, as compared with that in non-bicarbonate, HEPES-buffered solution, which was largely attributable to fast HCO3 (-) transport into the cells via NBCe1, supported by CAII activity. Our results show that within the time frame of determining physiological H(+) buffering in cells, fast transport and equilibration of CO2/H(+)/HCO3(-) can make a major contribution to the total "effective" H(+) buffer strength. Thus, "effective" cellular H(+) buffering is, to a large extent, attributable to membrane transport of base equivalents rather than a purely passive physicochemical process, and can be much larger than reported so far. Not only physicochemical H(+) buffering, but also rapid import of HCO3(-) via the electrogenic sodium-bicarbonate cotransporter NBCe1, supported by carbonic anhydrase II (CA II), was identified to enhance cytosolic H(+) buffer strength substantially.

  1. A study of different buffers to maximize viability of an oral Shigella vaccine.

    PubMed

    Chandrasekaran, Lakshmi; Lal, Manjari; Van De Verg, Lillian L; Venkatesan, Malabi M

    2015-11-17

    Live, whole cell killed and subunit vaccines are being developed for diarrheal diseases caused by V. cholerae, Shigella species, ETEC, and Campylobacter. Some of these vaccines can be administered orally since this route best mimics natural infection. Live vaccines administered orally have to be protected from the harsh acidic gastric environment. Milk and bicarbonate solutions have been administered to neutralize the stomach acid. For many Shigella vaccine trials, 100-120 ml of a bicarbonate solution is ingested followed by the live vaccine candidate, which is delivered in 30 ml of bicarbonate, water or saline. It is not clear if maximum bacterial viability is achieved under these conditions. Also, volumes of neutralizing buffer that are optimal for adults may be unsuitable for children and infants. To address these questions, we performed studies to determine the viability and stability of a Shigella sonnei vaccine candidate, WRSS1, in a mixture of different volumes of five different buffer solutions added to hydrochloric acid to simulate gastric acidity. Among the buffers tested, bicarbonate solution, rotavirus buffer and CeraVacx were better at neutralizing acid and maintaining the viability of WRSS1. Also, a much smaller volume of the neutralizing buffer was sufficient to counteract stomach acid while maintaining bacterial viability.

  2. GADOLINIUM OXALATE SOLUBILITY MEASUREMENTS IN NITRIC ACID SOLUTIONS

    SciTech Connect

    Pierce, R.

    2012-02-22

    HB-Line will begin processing Pu solutions during FY2012 that will involve the recovery of Pu using oxalate precipitation and filtration. After the precipitation and filtration processes, the filtrate solution will be transferred from HB-Line to H-Canyon. The presence of excess oxalate and unfiltered Pu oxalate solids in these solutions create a criticality safety issue if they are sent to H-Canyon without controls in H-Canyon. One approach involves H-Canyon receiving the filtrate solution into a tank that is poisoned with soluble gadolinium (Gd). Decomposition of the oxalate will occur within a subsequent H-Canyon vessel. The receipt of excess oxalate into the H-Canyon receipt tanks has the potential to precipitate a portion of the Gd poison in the receipt tanks. Because the amount of Gd in solution determines the maximum amount of Pu solids that H-Canyon can receive, H-Canyon Engineering requested that SRNL determine the solubility of Gd in aqueous solutions of 4-10 M nitric acid (HNO{sub 3}), 4-12 g/L Gd, and 0.15-0.25 M oxalic acid (H{sub 2}C{sub 2}O{sub 4}) at 25 C. The target soluble Gd concentration is 6 g/L. The data indicate that the target can be achieved above 6 M HNO{sub 3} and below 0.25 M H{sub 2}C{sub 2}O{sub 4}. For 6 M HNO{sub 3}, 10.5 g/L and 7 g/L Gd are soluble in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. In 4 M HNO{sub 3}, the Gd solubility drops significantly to 2 g/L and 0.25 g/L in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. The solubility of Gd at 8-10 M HNO{sub 3} exceeds the solubility at 6 M HNO{sub 3}. The data for 4 M HNO{sub 3} showed good agreement with data in the literature. To achieve a target of 6 g/L soluble Gd in solution in the presence of 0.15-0.25 M oxalate, the HNO{sub 3} concentration must be maintained at or above 6 M HNO{sub 3}.

  3. Mechanisms of buffer therapy resistance.

    PubMed

    Bailey, Kate M; Wojtkowiak, Jonathan W; Cornnell, Heather H; Ribeiro, Maria C; Balagurunathan, Yoganand; Hashim, Arig Ibrahim; Gillies, Robert J

    2014-04-01

    Many studies have shown that the acidity of solid tumors contributes to local invasion and metastasis. Oral pH buffers can specifically neutralize the acidic pH of tumors and reduce the incidence of local invasion and metastatic formation in multiple murine models. However, this effect is not universal as we have previously observed that metastasis is not inhibited by buffers in some tumor models, regardless of buffer used. B16-F10 (murine melanoma), LL/2 (murine lung) and HCT116 (human colon) tumors are resistant to treatment with lysine buffer therapy, whereas metastasis is potently inhibited by lysine buffers in MDA-MB-231 (human breast) and PC3M (human prostate) tumors. In the current work, we confirmed that sensitive cells utilized a pH-dependent mechanism for successful metastasis supported by a highly glycolytic phenotype that acidifies the local tumor microenvironment resulting in morphological changes. In contrast, buffer-resistant cell lines exhibited a pH-independent metastatic mechanism involving constitutive secretion of matrix degrading proteases without elevated glycolysis. These results have identified two distinct mechanisms of experimental metastasis, one of which is pH-dependent (buffer therapy sensitive cells) and one which is pH-independent (buffer therapy resistant cells). Further characterization of these models has potential for therapeutic benefit.

  4. Systems solutions by lactic acid bacteria: from paradigms to practice.

    PubMed

    de Vos, Willem M

    2011-08-30

    Lactic acid bacteria are among the powerhouses of the food industry, colonize the surfaces of plants and animals, and contribute to our health and well-being. The genomic characterization of LAB has rocketed and presently over 100 complete or nearly complete genomes are available, many of which serve as scientific paradigms. Moreover, functional and comparative metagenomic studies are taking off and provide a wealth of insight in the activity of lactic acid bacteria used in a variety of applications, ranging from starters in complex fermentations to their marketing as probiotics. In this new era of high throughput analysis, biology has become big science. Hence, there is a need to systematically store the generated information, apply this in an intelligent way, and provide modalities for constructing self-learning systems that can be used for future improvements. This review addresses these systems solutions with a state of the art overview of the present paradigms that relate to the use of lactic acid bacteria in industrial applications. Moreover, an outlook is presented of the future developments that include the transition into practice as well as the use of lactic acid bacteria in synthetic biology and other next generation applications. PMID:21995776

  5. Systems solutions by lactic acid bacteria: from paradigms to practice

    PubMed Central

    2011-01-01

    Lactic acid bacteria are among the powerhouses of the food industry, colonize the surfaces of plants and animals, and contribute to our health and well-being. The genomic characterization of LAB has rocketed and presently over 100 complete or nearly complete genomes are available, many of which serve as scientific paradigms. Moreover, functional and comparative metagenomic studies are taking off and provide a wealth of insight in the activity of lactic acid bacteria used in a variety of applications, ranging from starters in complex fermentations to their marketing as probiotics. In this new era of high throughput analysis, biology has become big science. Hence, there is a need to systematically store the generated information, apply this in an intelligent way, and provide modalities for constructing self-learning systems that can be used for future improvements. This review addresses these systems solutions with a state of the art overview of the present paradigms that relate to the use of lactic acid bacteria in industrial applications. Moreover, an outlook is presented of the future developments that include the transition into practice as well as the use of lactic acid bacteria in synthetic biology and other next generation applications. PMID:21995776

  6. Systems solutions by lactic acid bacteria: from paradigms to practice.

    PubMed

    de Vos, Willem M

    2011-08-30

    Lactic acid bacteria are among the powerhouses of the food industry, colonize the surfaces of plants and animals, and contribute to our health and well-being. The genomic characterization of LAB has rocketed and presently over 100 complete or nearly complete genomes are available, many of which serve as scientific paradigms. Moreover, functional and comparative metagenomic studies are taking off and provide a wealth of insight in the activity of lactic acid bacteria used in a variety of applications, ranging from starters in complex fermentations to their marketing as probiotics. In this new era of high throughput analysis, biology has become big science. Hence, there is a need to systematically store the generated information, apply this in an intelligent way, and provide modalities for constructing self-learning systems that can be used for future improvements. This review addresses these systems solutions with a state of the art overview of the present paradigms that relate to the use of lactic acid bacteria in industrial applications. Moreover, an outlook is presented of the future developments that include the transition into practice as well as the use of lactic acid bacteria in synthetic biology and other next generation applications.

  7. Sorption of acid red 57 from aqueous solution onto sepiolite.

    PubMed

    Alkan, Mahir; Demirbaş, Ozkan; Celikçapa, Sermet; Doğan, Mehmet

    2004-12-10

    Sepiolite, a highly porous mineral, is becoming widely used as an alternative material in areas where sorptive, catalytic and rheological applications are required. High ion exchange capacity and high surface area and more importantly its relatively cheap price make it an attractive adsorbent. In this study, the adsorption of acid red 57 by natural mesoporous sepiolite has been examined in order to measure the ability of this mineral to remove coloured textile dyes from wastewater. For this purpose, a series of batch adsorption tests of acid red 57 from aqueous sepiolite solutions have been systematically investigated as a function of parameters such as pH, ionic strength and temperature. Adsorption equilibrium was reached within 1h. The removal of acid red 57 decreases with pH from 3 to 9 and temperature from 25 to 55 degrees C, whereas it increases with ionic strength from 0 to 0.5 mol L(-1). Adsorption isotherms of acid red on sepiolite were determined and correlated with common isotherm equations such as Langmuir and Freundlich models. It was found that the Langmuir model appears to fit the isotherm data better than the Freundlich model. The physical properties of this adsorbent were consistent with the parameters obtained from the isotherm equations. Approximately, 21.49% weight loss was observed. The surface area value of sepiolite was 342 m2 g(-1) at 105 degrees C, and it increased to 357 m2 g(-1) at 200 degrees C. Further increase in temperature caused channel plugging and crystal structure deformation, as a result the surface area values showed a decrease with temperature. The data obtained from adsorption isotherms at different temperatures have been used to calculate some thermodynamic quantities such as the Gibbs energy, heat and entropy of adsorption. The thermodynamic data indicate that acid red 57 adsorption onto sepiolite is characterized by physical adsorption. The dimensionless separation factor (RL) have shown that sepiolite can be used for

  8. Airborne soil dust and its importance in buffering of atmospheric acidity and critical load assessment, over the semi arid tract of northern India.

    NASA Astrophysics Data System (ADS)

    Sharma, Disha; Kulshrestha, Umesh

    Airborne soil dust and its importance in buffering of atmospheric acidity and critical load assessment, over the semi arid tract of northern India. The Critical Load approach alongwith integrated assessment models has been used in the European nations for policy formations to reduce acidic emissions. This unique approach was applied to assess the of vulnerability of natural systems to the present day atmospheric pollution scenario. The calculated values of critical loads of sulphur ( 225 - 275 eq/ha/yr) and nitrogen (298 - 303 eq/ha/yr), for the soil system in Delhi, were calculated with respect to Anjan grass, Hibiscus and Black siris. The present loads of sulphur (PL(S) = 26.40 eq/ha/yr) and nitrogen (PL(N) = 36.51 eq/ha/yr) were found to be much lower than their critical loads without posing any danger of atmospheric acidic deposition on the soil systems. The study indicated that the system is still protective due to high pH of soil. The nature of buffering capability of calcium derived from soil dust can be considered as a natural tool to combat acidification in the Indian region. The results showed that the pollution status in Delhi is still within the safe limits. However, at the pace at which the city is growing, it is likely that in coming decades, it may exceed these critical values. In order to set deposition limits and avoid adverse effects of acidic deposition this approach can be applied in India too. Such approach is very useful, not only in abating pollution but also in devising means of cost optimal emission abatement strategies.

  9. Effect of synovial fluid, phosphate-buffered saline solution, and water on the dissolution and corrosion properties of CoCrMo alloys as used in orthopedic implants.

    PubMed

    Lewis, A C; Kilburn, M R; Papageorgiou, I; Allen, G C; Case, C P

    2005-06-15

    The corrosion and dissolution of high- and low-carbon CoCrMo alloys, as used in orthopedic joint replacements, were studied by immersing samples in phosphate-buffered saline (PBS), water, and synovial fluid at 37 degrees C for up to 35 days. Bulk properties were analyzed with a fine ion beam microscope. Surface analyses by X-ray photoelectron spectroscopy and Auger electron spectroscopy showed surprisingly that synovial fluid produced a thin oxide/hydroxide layer. Release of ions into solution from the alloy also followed an unexpected pattern where synovial fluid, of all the samples, had the highest Cr concentration but the lowest Co concentration. The presence of carbide inclusions in the alloy did not affect the corrosion or the dissolution mechanisms, although the carbides were a significant feature on the metal surface. Only one mechanism was recognized as controlling the thickness of the oxide/hydroxide interface. The analysis of the dissolved metal showed two mechanisms at work: (1) a protein film caused ligand-induced dissolution, increasing the Cr concentration in synovial fluid, and was explained by the equilibrium constants; (2) corrosion at the interface increased the Co in PBS. The effect of prepassivating the samples (ASTM F-86-01) did not always have the desired effect of reducing dissolution. The release of Cr into PBS increased after prepassivation. The metal-synovial fluid interface did not contain calcium phosphate as a deposit, typically found where samples are exposed to calcium rich bodily fluids.

  10. Electrocatalytic hydrogenation of 5-hydroxymethylfurfural in acidic solution.

    PubMed

    Kwon, Youngkook; Birdja, Yuvraj Y; Raoufmoghaddam, Saeed; Koper, Marc T M

    2015-05-22

    Electrocatalytic hydrogenation of 5-hydroxymethylfurfural (HMF) is studied on solid metal electrodes in acidic solution (0.5 M H2 SO4 ) by correlating voltammetry with on-line HPLC product analysis. Three soluble products from HMF hydrogenation are distinguished: 2,5-dihydroxymethylfuran (DHMF), 2,5-dihydroxymethyltetrahydrofuran (DHMTHF), and 2,5-dimethyl-2,3-dihydrofuran (DMDHF). Based on the dominant reaction products, the metal catalysts are divided into three groups: (1) metals mainly forming DHMF (Fe, Ni, Cu, and Pb), (2) metals forming DHMF and DMDHF depending on the applied potentials (Co, Ag, Au, Cd, Sb, and Bi), and (3) metals forming mainly DMDHF (Pd, Pt, Al, Zn, In, and Sb). Nickel and antimony are the most active catalysts for DHMF (0.95 mM cm(-2) at ca. -0.35 VRHE and -20 mA cm(-2) ) and DMDHF (0.7 mM cm(-2) at -0.6 VRHE and -5 mA cm(-2) ), respectively. The pH of the solution plays an important role in the hydrogenation of HMF: acidic condition lowers the activation energy for HMF hydro-genation and hydrogenates the furan ring further to tetrahydrofuran.

  11. Reduction of hexavalent chromium by ascorbic acid in aqueous solutions.

    PubMed

    Xu, Xiang-Rong; Li, Hua-Bin; Li, Xiao-Yan; Gu, Ji-Dong

    2004-11-01

    Hexavalent chromium is a priority pollutant in the USA and many other countries. Reduction of Cr(VI) to Cr(III) is environmentally favorable as the latter species is not toxic to most living organisms and also has a low mobility and bioavailability. Reduction of Cr(VI) by ascorbic acid (vitamin C) as a reductant was studied using potassium dichromate solution as the model pollutant. Effects of concentration of vitamin C, pH, temperature, irradiation and reaction time on the reduction of Cr(VI) were examined. Cr(VI) might be reduced by vitamin C not only in acidic conditions but also in weakly alkaline solutions. The reduction of Cr(VI) by vitamin C might occur not only under irradiation but also in the dark. Vitamin C is an important biological reductant in humans and animals, and not toxic. It is water-soluble and can easily permeate through various types of soils. The results indicate that vitamin C could be used in effective remediation of Cr(VI)-contaminated soils and groundwater in a wide range of pH, with or without sunlight. PMID:15488923

  12. Reduction of hexavalent chromium by ascorbic acid in aqueous solutions.

    PubMed

    Xu, Xiang-Rong; Li, Hua-Bin; Li, Xiao-Yan; Gu, Ji-Dong

    2004-11-01

    Hexavalent chromium is a priority pollutant in the USA and many other countries. Reduction of Cr(VI) to Cr(III) is environmentally favorable as the latter species is not toxic to most living organisms and also has a low mobility and bioavailability. Reduction of Cr(VI) by ascorbic acid (vitamin C) as a reductant was studied using potassium dichromate solution as the model pollutant. Effects of concentration of vitamin C, pH, temperature, irradiation and reaction time on the reduction of Cr(VI) were examined. Cr(VI) might be reduced by vitamin C not only in acidic conditions but also in weakly alkaline solutions. The reduction of Cr(VI) by vitamin C might occur not only under irradiation but also in the dark. Vitamin C is an important biological reductant in humans and animals, and not toxic. It is water-soluble and can easily permeate through various types of soils. The results indicate that vitamin C could be used in effective remediation of Cr(VI)-contaminated soils and groundwater in a wide range of pH, with or without sunlight.

  13. Buffer Standards for pH Measurement of N-(2-Hydroxyethyl)piperazine-N’-2-ethanesulfonic Acid (HEPES) for I = 0.16 mol·kg−1 from 5 to 55°C

    PubMed Central

    Roy, Rabindra N.; Roy, Lakshmi N.; Ashkenazi, Shahaf; Wollen, Joshua T.; Dunseth, Craig D.; Fuge, Michael S.; Durden, Jared L.; Roy, Chandra N.; Hughes, Hannah M.; Morris, Brett T.; Cline, Kevin L.

    2009-01-01

    The values of the second dissociation constant, pK2 of N-(2-hydroxyethyl) piperazine-N’-2-ethanesulfonic acid (HEPES) have been reported at 12 temperatures over the temperature range 5 to 55°C, including 37°C. This paper reports the results for the paH of eight isotonic saline buffer solutions with an I = 0.16 mol•kg−1 including compositions: (a) HEPES (0.01 mol•kg−1) + NaHEPES (0.01 mol•kg−1) + NaCl (0.15 mol•kg−1); (b) HEPES (0.02 mol•kg−1) + NaHEPES (0.02 mol•kg−1) + NaCl (0.14 mol•kg−1); (c) HEPES (0.03 mol•kg−1) + NaHEPES (0.03 mol•kg−1) + NaCl (0.13 mol•kg−1); (d) HEPES (0.04 mol•kg−1) + NaHEPES (0.04 mol•kg−1) + NaCl (0.12 mol•kg−1); (e) HEPES (0.05 mol•kg−1) + NaHEPES (0.05 mol•kg−1) + NaCl (0.11 mol•kg−1); (f) HEPES (0.06 mol•kg−1) + NaHEPES (0.06 mol•kg−1) + NaCl (0.10 mol•kg−1); (g) HEPES (0.07 mol•kg−1) + NaHEPES (0.07 mol•kg−1) + NaCl (0.09 mol•kg−1); and (h) HEPES (0.08 mol•kg−1) + NaHEPES (0.08 mol•kg−1) + NaCl (0.08 mol•kg−1). Conventional paH values, for all eight buffer solutions from 5 to 55°C have been calculated. The operational pH values with liquid junction corrections, at 25 and 37°C have been determined based on the NBS/NIST standard between the physiological phosphate standard and four buffer solutions. These are recommended as pH standards for physiological fluids in the range of pH 7.3 to 7.5 at I = 0.16 mol•kg−1. PMID:20161485

  14. [Bioconversion of conjugated linoleic acid by resting cells of Lactobacillus plantarum ZS2058 in potassium phosphate buffer system].

    PubMed

    Niu, Xiao-yan; Chen, Wei; Tian, Feng-wei; Zhao, Jian-xin; Zhang, Hao

    2007-04-01

    Lactobacillus plantarum ZS2058, which was screened from the Chinese traditional fermented vegetable, has the capacity to convert the linoleic acid (LA) into conjugated linoleic acid (CLA). Some specific isomers of CLA with potentially beneficial physiological and anticarcinogenic effects, were efficiently produced from free linoleic acid by washed cells of Lactobacillus plantarum ZS2058 under aerobic conditions. The produced CLA isomers are identified as the mixture of cis-9, trans-ll-octadecadienoic acid (CLA1) trans-10, cis-12-octadecadienoic acid (CLA2), 96.4% of which is CLA1. The washed cells of Lactobacillus plantarum ZS2058 producing high levels of c9, t11-CLA were obtained by cultivated in MRS media containing 0.5 mg/mL linoleic acid, indicating that the enzyme system for CLA production is induced by linoleic acid. After a 24-hour bioconversion at 37 degrees C with shaking (120 r/min), 312.4 microg/mL c9, t11-CLA is produced. And after a 36-hour bioconversion, the content of c9, t11-CLA decreases while hydroxy-octadecaenoic acid increases. In addition, the c9, t11-CLA isomer can be transformed to hydroxy- octadecaenoic acid when the mixed CLA (c9, t11-CLA and t10, c12-CLA) were used as the substrate, which suggests that c9, t11-CLA is one of the intermediates of the bioconversion products from free LA by washed cells of Lactobacillus plantarum ZS2058.

  15. Colorimetric and fluorometric discrimination of geometrical isomers (maleic acid vs fumaric acid) with real-time detection of maleic acid in solution and food additives.

    PubMed

    Samanta, Soham; Kar, Chirantan; Das, Gopal

    2015-09-01

    Heterobis imine Schiff base probe L is able to discriminate geometrical isomers (maleic acid vs fumaric acid) through sharp colorimetric as well as fluorogenic responses even conspicuous with the naked eye. Colorimetric as well as fluorogenic sensing of maleic acid among various carboxylic acids was also demonstrated in ethanol-buffer medium. Sensing behavior of L was corroborated by (1)H NMR spectra, mass spectrometry, and theoretical calculations. Subsequently sensing behavior of L was used to probe maleic acid in starch rich food samples.

  16. Colorimetric and fluorometric discrimination of geometrical isomers (maleic acid vs fumaric acid) with real-time detection of maleic acid in solution and food additives.

    PubMed

    Samanta, Soham; Kar, Chirantan; Das, Gopal

    2015-09-01

    Heterobis imine Schiff base probe L is able to discriminate geometrical isomers (maleic acid vs fumaric acid) through sharp colorimetric as well as fluorogenic responses even conspicuous with the naked eye. Colorimetric as well as fluorogenic sensing of maleic acid among various carboxylic acids was also demonstrated in ethanol-buffer medium. Sensing behavior of L was corroborated by (1)H NMR spectra, mass spectrometry, and theoretical calculations. Subsequently sensing behavior of L was used to probe maleic acid in starch rich food samples. PMID:26246182

  17. Arsenic removal from acidic solutions with biogenic ferric precipitates.

    PubMed

    Ahoranta, Sarita H; Kokko, Marika E; Papirio, Stefano; Özkaya, Bestamin; Puhakka, Jaakko A

    2016-04-01

    Treatment of acidic solution containing 5g/L of Fe(II) and 10mg/L of As(III) was studied in a system consisting of a biological fluidized-bed reactor (FBR) for iron oxidation, and a gravity settler for iron precipitation and separation of the ferric precipitates. At pH 3.0 and FBR retention time of 5.7h, 96-98% of the added Fe(II) precipitated (99.1% of which was jarosite). The highest iron oxidation and precipitation rates were 1070 and 28mg/L/h, respectively, and were achieved at pH 3.0. Subsequently, the effect of pH on arsenic removal through sorption and/or co-precipitation was examined by gradually decreasing solution pH from 3.0 to 1.6 (feed pH). At pH 3.0, 2.4 and 1.6, the highest arsenic removal efficiencies obtained were 99.5%, 80.1% and 7.1%, respectively. As the system had ferric precipitates in excess, decreased arsenic removal was likely due to reduced co-precipitation at pH<2.4. As(III) was partially oxidized to As(V) in the system. In shake flask experiments, As(V) sorbed onto jarosite better than As(III). Moreover, the sorption capacity of biogenic jarosite was significantly higher than that of synthetic jarosite. The developed bioprocess simultaneously and efficiently removes iron and arsenic from acidic solutions, indicating potential for mining wastewater treatment. PMID:26705889

  18. Adaptation of sweeteners in water and in tannic acid solutions.

    PubMed

    Schiffman, S S; Pecore, S D; Booth, B J; Losee, M L; Carr, B T; Sattely-Miller, E; Graham, B G; Warwick, Z S

    1994-03-01

    Repeated exposure to a tastant often leads to a decrease in magnitude of the perceived intensity; this phenomenon is termed adaptation. The purpose of this study was to determine the degree of adaptation of the sweet response for a variety of sweeteners in water and in the presence of two levels of tannic acid. Sweetness intensity ratings were given by a trained panel for 14 sweeteners: three sugars (fructose, glucose, sucrose), two polyhydric alcohols (mannitol, sorbitol), two terpenoid glycosides (rebaudioside-A, stevioside), two dipeptide derivatives (alitame, aspartame), one sulfamate (sodium cyclamate), one protein (thaumatin), two N-sulfonyl amides (acesulfame-K, sodium saccharin), and one dihydrochalcone (neohesperidin dihydrochalcone). Panelists were given four isointense concentrations of each sweetener by itself and in the presence of two concentrations of tannic acid. Each sweetener concentration was tasted and rated four consecutive times with a 30 s interval between each taste and a 2 min interval between each concentration. Within a taste session, a series of concentrations of a given sweetener was presented in ascending order of magnitude. Adaptation was calculated as the decrease in intensity from the first to the fourth sample. The greatest adaptation in water solutions was found for acesulfame-K, Na saccharin, rebaudioside-A, and stevioside. This was followed by the dipeptide sweeteners, alitame and aspartame. The least adaptation occurred with the sugars, polyhydric alcohols, and neohesperidin dihydrochalcone. Adaptation was greater in tannic acid solutions than in water for six sweeteners. Adaptation of sweet taste may result from the desensitization of sweetener receptors analogous to the homologous desensitization found in the beta adrenergic system.

  19. Precipitation of plutonium from acidic solutions using magnesium oxide

    SciTech Connect

    Jones, S.A.

    1994-09-06

    Plutonium (IV) is only marginally soluble in alkaline solution. Precipitation of plutonium using sodium or potassium hydroxide to neutralize acidic solutions produces a gelatinous solid that is difficult to filter and an endpoint that is difficult to control. If the pH of the solution is too high, additional species precipitate producing an increased volume of solids separated. The use of magnesium oxide as a reagent has advantages. It is added as a solid (volume of liquid waste produced is minimized), the pH is self-limiting (pH does not exceed about 8.5), and the solids precipitated are more granular (larger particle size) than those produced using KOH or NaOH. Following precipitation, the raffinate is expected to meet criteria for disposal to tank farms. The solid will be heated in a furnace to dry it and convert any hydroxide salts to the oxide form. The material will be cooled in a desiccator. The material is expected to meet vault storage criteria.

  20. Conformation of poly(γ-glutamic acid) in aqueous solution.

    PubMed

    Muroga, Yoshio; Nakaya, Asami; Inoue, Atsuki; Itoh, Daiki; Abiru, Masaya; Wada, Kaori; Takada, Masako; Ikake, Hiroki; Shimizu, Shigeru

    2016-04-01

    Local conformation and overall conformation of poly(γ-DL-glutamic acid) (PγDLGA) and poly(γ-L-glutamic acid) (PγLGA) in aqueous solution was studied as a function of degree of ionization ε by (1) H-NMR, circular dichroism, and potentiometric titration. It was clarified that their local conformation is represented by random coil over an entire ε range and their overall conformation is represented by expanded random-coil in a range of ε > ε(*) , where ε(*) is about 0.3, 0.35, 0.45, and 0.5 for added-salt concentration of 0.02M, 0.05M, 0.1M, and 0.2M, respectively. In a range of ε < ε(*) , however, ε dependence of their overall conformation is significantly differentiated from each other. PγDLGA tends to aggregate intramolecularly and/or intermolecularly with decreasing ε, but PγLGA still behaves as expanded random-coil. It is speculated that spatial arrangement of adjacent carboxyl groups along the backbone chain essentially affects the overall conformation of PγGA in acidic media.

  1. The influence of the nature of background anions on the buffer capacity of glycine-containing electrolytes for nickel electroplating

    NASA Astrophysics Data System (ADS)

    Dolgikh, O. V.; Zuen, Vu Tkhi; Sotskaya, N. V.

    2009-06-01

    The buffer properties of acetate, sulfate, and chloride glycine-containing electrolytes for nickel electroplating were studied. Various forms of the amino acid and background anions were shown to act in solution as two buffer systems related by competitive complex formation. The buffer capacity of a solution was then the result of the joint action of these systems. The contribution of each of them was determined by its absolute concentration in solution on the one hand and changes in this concentration caused by the addition of H+ or OH- ions on the other.

  2. Infrared optical constants of H2O ice, amorphous nitric acid solutions, and nitric acid hydrates

    NASA Technical Reports Server (NTRS)

    Toon, Owen B.; Koehler, Birgit G.; Middlebrook, Ann M.; Tolbert, Margaret A.; Jordon, Joseph

    1994-01-01

    We determined the infrared optical constants of nitric acid trihydrate, nitric acid dihydrate, nitric acid monohydrate, and solid amorphous nitric acid solutions which crystallize to form these hydrates. We have also found the infrared optical constants of H2O ice. We measured the transmission of infrared light throught thin films of varying thickness over the frequency range from about 7000 to 500/cm at temperatures below 200 K. We developed a theory for the transmission of light through a substrate that has thin films on both sides. We used an iterative Kramers-Kronig technique to determine the optical constants which gave the best match between measured transmission spectra and those calculated for a variety of films of different thickness. These optical constants should be useful for calculations of the infrared spectrum of polar stratospheric clouds.

  3. Isolation and characterization of Chinese standard fulvic acid sub-fractions separated from forest soil by stepwise elution with pyrophosphate buffer.

    PubMed

    Bai, Yingchen; Wu, Fengchang; Xing, Baoshan; Meng, Wei; Shi, Guolan; Ma, Yan; Giesy, John P

    2015-01-01

    XAD-8 adsorption technique coupled with stepwise elution using pyrophosphate buffers with initial pH values of 3, 5, 7, 9, and 13 was developed to isolate Chinese standard fulvic acid (FA) and then separated the FA into five sub-fractions: FApH3, FApH5, FApH7, FApH9 and FApH13, respectively. Mass percentages of FApH3-FApH13 decreased from 42% to 2.5%, and the recovery ratios ranged from 99.0% to 99.5%. Earlier eluting sub-fractions contained greater proportions of carboxylic groups with greater polarity and molecular mass, and later eluting sub-fractions had greater phenolic and aliphatic content. Protein-like components, as well as amorphous and crystalline poly(methylene)-containing components were enriched using neutral and basic buffers. Three main mechanisms likely affect stepwise elution of humic components from XAD-8 resin with pyrophosphate buffers including: 1) the carboxylic-rich sub-fractions are deprotonated at lower pH values and eluted earlier, while phenolic-rich sub-fractions are deprotonated at greater pH values and eluted later. 2) protein or protein-like components can be desorbed and eluted by use of stepwise elution as progressively greater pH values exceed their isoelectric points. 3) size exclusion affects elution of FA sub-fractions. Successful isolation of FA sub-fractions will benefit exploration of the origin, structure, evolution and the investigation of interactions with environmental contaminants. PMID:25735451

  4. Isolation and characterization of Chinese standard fulvic acid sub-fractions separated from forest soil by stepwise elution with pyrophosphate buffer.

    PubMed

    Bai, Yingchen; Wu, Fengchang; Xing, Baoshan; Meng, Wei; Shi, Guolan; Ma, Yan; Giesy, John P

    2015-03-04

    XAD-8 adsorption technique coupled with stepwise elution using pyrophosphate buffers with initial pH values of 3, 5, 7, 9, and 13 was developed to isolate Chinese standard fulvic acid (FA) and then separated the FA into five sub-fractions: FApH3, FApH5, FApH7, FApH9 and FApH13, respectively. Mass percentages of FApH3-FApH13 decreased from 42% to 2.5%, and the recovery ratios ranged from 99.0% to 99.5%. Earlier eluting sub-fractions contained greater proportions of carboxylic groups with greater polarity and molecular mass, and later eluting sub-fractions had greater phenolic and aliphatic content. Protein-like components, as well as amorphous and crystalline poly(methylene)-containing components were enriched using neutral and basic buffers. Three main mechanisms likely affect stepwise elution of humic components from XAD-8 resin with pyrophosphate buffers including: 1) the carboxylic-rich sub-fractions are deprotonated at lower pH values and eluted earlier, while phenolic-rich sub-fractions are deprotonated at greater pH values and eluted later. 2) protein or protein-like components can be desorbed and eluted by use of stepwise elution as progressively greater pH values exceed their isoelectric points. 3) size exclusion affects elution of FA sub-fractions. Successful isolation of FA sub-fractions will benefit exploration of the origin, structure, evolution and the investigation of interactions with environmental contaminants.

  5. Isolation and Characterization of Chinese Standard Fulvic Acid Sub-fractions Separated from Forest Soil by Stepwise Elution with Pyrophosphate Buffer

    NASA Astrophysics Data System (ADS)

    Bai, Yingchen; Wu, Fengchang; Xing, Baoshan; Meng, Wei; Shi, Guolan; Ma, Yan; Giesy, John P.

    2015-03-01

    XAD-8 adsorption technique coupled with stepwise elution using pyrophosphate buffers with initial pH values of 3, 5, 7, 9, and 13 was developed to isolate Chinese standard fulvic acid (FA) and then separated the FA into five sub-fractions: FApH3, FApH5, FApH7, FApH9 and FApH13, respectively. Mass percentages of FApH3-FApH13 decreased from 42% to 2.5%, and the recovery ratios ranged from 99.0% to 99.5%. Earlier eluting sub-fractions contained greater proportions of carboxylic groups with greater polarity and molecular mass, and later eluting sub-fractions had greater phenolic and aliphatic content. Protein-like components, as well as amorphous and crystalline poly(methylene)-containing components were enriched using neutral and basic buffers. Three main mechanisms likely affect stepwise elution of humic components from XAD-8 resin with pyrophosphate buffers including: 1) the carboxylic-rich sub-fractions are deprotonated at lower pH values and eluted earlier, while phenolic-rich sub-fractions are deprotonated at greater pH values and eluted later. 2) protein or protein-like components can be desorbed and eluted by use of stepwise elution as progressively greater pH values exceed their isoelectric points. 3) size exclusion affects elution of FA sub-fractions. Successful isolation of FA sub-fractions will benefit exploration of the origin, structure, evolution and the investigation of interactions with environmental contaminants.

  6. Novel Regenerated Solvent Extraction Processes for the Recovery of Carboxylic Acids or Ammonia from Aqueous Solutions Part II. Recovery of Ammonia from Sour Waters

    SciTech Connect

    Poole, L.J.; King, C.J.

    1990-03-01

    Two novel regenerated solvent extraction processes are examined. The first process has the potential to reduce the energy costs inherent in the recovery of low-volatility carboxylic acids from dilute aqueous solutions. The second process has the potential for reducing the energy costs required for separate recovery of ammonia and acid gases (e.g. CO{sub 2} and H{sub 2}S) from industrial sour waters. The recovery of carboxylic acids from dilute aqueous solution can be achieved by extraction with tertiary amines. An approach for regeneration and product recovery from such extracts is to back-extract the carboxylic acid with a water-soluble, volatile tertiary amine, such as trimethylamine. The resulting trimethylammonium carboxylate solution can be concentrated and thermally decomposed, yielding the product acid and the volatile amine for recycle. Experimental work was performed with lactic acid, SUCCiOlC acid, and fumaric acid. Equilibrium data show near-stoichiometric recovery of the carboxylic acids from an organic solution of Alamine 336 into aqueous solutions of trimethylamine. For fumaric and succinic acids, partial evaporation of the aqueous back extract decomposes the carboxylate and yields the acid product in crystalline form. The decomposition of aqueous solutions of trimethylammonium lactates was not carried out to completion, due to the high water solubility of lactic acid and the tendency of the acid to self-associate. The separate recovery of ammonia and acid gases from sour waters can be achieved by combining steam-stripping of the acid gases with simultaneous removal of ammonia by extraction with a liquid cation exchanger. The use of di-2,4,4-trimethylpentyl phosphinic acid as the liquid cation exchanger is explored in this work. Batch extraction experiments were carried out to measure the equilibrium distribution ratio of ammonia between an aqueous buffer solution and an organic solution of the phosphinic acid (0.2N) in Norpar 12. The concentration

  7. A Pollutant Transformation Laboratory Exercise for Environmental Chemistry: The Reduction of Nitrobenzenes by Anaerobic Solutions of Humic Acid

    ERIC Educational Resources Information Center

    Dunnivant, Frank M.; Reynolds, Mark-Cody

    2007-01-01

    The laboratory experiment, which acts as a capstone, integrated lecture-laboratory exercise involving solution preparation, pH buffers, [E[subscript]H] (reduction potential) buffers, organic reaction mechanisms, reaction kinetics, and instrumental analysis is presented. The students completing the lecture and laboratory exercises could gain a…

  8. The extraction of actinides from nitric acid solutions with diamides of dipicolinic acid

    NASA Astrophysics Data System (ADS)

    Lapka, Joseph L.; Paulenova, Alena; Alyapyshev, Mikhail Yu; Babain, Vasiliy A.; Law, Jack D.; Herbst, R. Scott

    2010-03-01

    Diamides of dipicolinic acid (N,N'-diethyl-N,N'-ditolyl-dipicolinamide, EtTDPA) were synthesized and evaluated for their extraction capability for actinides. In this work the extractions of neptunium(V), protactinium(V), and thorium(IV) with EtTDPA in a polar fluorinated diluent from nitric acid were investigated. EtTDPA shows a high affinity for Th(IV) even at millimolar concentrations. Np(V) and Pa(V) are both reasonably extractable with EtTDPA; however, near saturated solutions are required to achieve appreciable distribution ratios. A comparison with previously published actinide extraction data is given.

  9. Peak shapes of acids and bases under overloaded conditions in reversed-phase liquid chromatography, with weakly buffered mobile phases of various pH: A thermodynamic interpretation

    SciTech Connect

    Gritti, Fabrice; Guiochon, Georges A

    2009-01-01

    We measured overloaded band profiles for a series of nine compounds (phenol, caffeine, 3-phenyl 1-propanol, 2-phenylbutyric acid, amphetamine, aniline, benzylamine, p-toluidine, and procainamidium chloride) on columns packed with four different C{sub 18}-bonded packing materials: XTerra-C{sub 18}, Gemini-C{sub 18}, Luna-C{sub 18}(2), and Halo-C{sub 18}, using buffered methanol-water mobile phases. The {sub W}{sup S}pH of the mobile phase was increased from 2.6 to 11.3. The buffer concentration (either phosphate, acetate, or carbonate buffers) was set constant at values below the maximum concentration of the sample in the band. The influence of the surface chemistry of the packing material on the retention and the shape of the peaks was investigated. Adsorbents having a hybrid inorganic/organic structure tend to give peaks exhibiting moderate or little tailing. The retention and the shape of the band profiles can easily be interpreted at {sub W}{sup S}pHs that are well above or well below the {sub W}{sup S}pK{sub a} of the compound studied. In contrast, the peak shapes in the intermediary pH range (i.e., close to the compound {sub W}{sup S}pK{sub a}) have rarely been studied. These shapes reveal the complexity of the competitive adsorption behavior of couples of acido-basic conjugated compounds at {sub W}{sup S}pHs that are close to their {sub W}{sup S}pK{sub a}. They also reveal the role of the buffer capacity on the resulting peak shape. With increasing {sub W}{sup S}pH, the overloaded profiles are first langmuirian (isotherm type I) at low {sub W}{sup S}pHs, they become S-shaped (isotherm type II), then anti-langmuirian (isotherm type III), S-shaped again at intermediate {sub W}{sup S}pHs, and finally return to a langmuirian shape at high {sub W}{sup S}pHs. A new general adsorption isotherm model that takes into account the dissociation equilibrium of conjugated acidic and basic species in the bulk mobile phase accounts for these transient band shapes. An

  10. Radiolysis gases from nitric acid solutions containing HSA and HAN

    SciTech Connect

    Smith, J.R.

    1994-10-28

    The concentration of hydrogen (H{sub 2}) in the radiolytically produced off-gas from 2.76-4.25M HNO{sub 3}/PU solutions has been found to be greatly reduced in the presence of sulfamic acid (HSA) and hydroxylamine nitrate (HAN). The H{sub 2} concentration ([H{sub 2}]) is reduced from 35 percent to about 4 percent by dilution caused from an increase in the production rates of nitrogen (N{sub 2}), nitrous oxide (N{sub 2}O), and oxygen (O{sub 2}) gases. The generation rate of H{sub 2} was not affected by HSA or HAN giving a measured radiolytic yield, G(H{sub 2}), value of 0.201 molecules/100 eV for 2.765M NO{sub 3}{sup -} solution (a value of 0.213 is predicted from previous data). The G(H{sub 2}) values are dependent on the solution nitrate concentration ([NO{sub 3}{sup -}]). The generation rates of N{sub 2}, N{sub 2}O, and O{sub 2} are not dependent on the [NO{sub 3}{sup -}] in this narrow range, but are dependent on the presence of HSA and the concentration of HAN. The percentage [H{sub 2}] for the 2.5 to 3.0M NO{sub 3}{sup -} range expected in the off- from the FB-Line Pu{sup +3} Hold Tanks is conservatively estimated to be about 3.5 to 4.5 % for Pu + 3 solutions initially containing 0.023M HAN/0.165M HSA. The upper limit [H{sub 2}] may actually be about 4.1 % (4.3 % at 90 % confidence limits) but more {open_quotes}initial{close_quotes} off-gas rate data is needed at about 2.9M [NO{sub 3}{sup -}] in Pu{sup +3} solution for verification. Addition of ascorbic acid had no effect on the off-gas rate of Pu{sup +3} solutions containing HSA and NO{sub 3}{sup -} concentrations higher than those expected in the hold tanks. The maximum {open_quotes}hold time{close_quotes} for 50 grams/liter Pu{sup +3}/0.165M HSA/0.023M HAN/2.5-3.0M HNO{sub 3} solution is 20.3{+-}2.1 days. After this time the HSA initially present will become exhausted and the [H{sub 2}] will increase to 35 %. This hold time may be longer in [NO{sub 3}{sup -}] < 3.0M, but again more study is needed.

  11. GADOLINIUM OXALATE SOLUBILITY MEASUREMENTS IN NITRIC ACID SOLUTIONS

    SciTech Connect

    Pierce, R. A.

    2012-03-12

    HB-Line will begin processing Pu solutions during FY2012 that will involve the recovery of Pu using oxalate precipitation and filtration. After the precipitation and filtration processes, the filtrate solution will be transferred from HB-Line to H-Canyon. The presence of excess oxalate and unfiltered Pu oxalate solids in these solutions create a criticality safety issue if they are sent to H-Canyon without controls in H-Canyon. One approach involves H-Canyon receiving the filtrate solution into a tank that is poisoned with soluble gadolinium (Gd). Decomposition of the oxalate will occur within a subsequent H-Canyon vessel. The receipt of excess oxalate into the H-Canyon receipt tanks has the potential to precipitate a portion of the Gd poison in the receipt tanks. Because the amount of Gd in solution determines the maximum amount of Pu solids that H-Canyon can receive, H-Canyon Engineering requested that SRNL determine the solubility of Gd in aqueous solutions of 4-10 M nitric acid (HNO{sub 3}), 4-12 g/L Gd, and 0.15-0.25 M oxalic acid (H{sub 2}C{sub 2}O{sub 4}) at 25 °C. The target soluble Gd concentration is 6 g/L. The data indicate that the target can be achieved above 6 M HNO{sub 3} and below 0.25 M H{sub 2}C{sub 2}O{sub 4}. At 25 °C, for 6 M HNO{sub 3}, 11 g/L and 7 g/L Gd are soluble in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. In 4 M HNO{sub 3}, the Gd solubility drops significantly to 2.5 g/L and 0.8 g/L in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. The solubility of Gd at 8-10 M HNO{sub 3} exceeds the solubility at 6 M HNO{sub 3}. The data for 4 M HNO{sub 3} showed good agreement with data in the literature. To achieve a target of 6 g/L soluble Gd in solution in the presence of 0.15-0.25 M oxalate, the HNO{sub 3} concentration must be maintained at or above 6 M HNO{sub 3}. The solubility of Gd in 4 M HNO{sub 3} with 0.15 M oxalate at 10 °C is about 1.5 g/L. For 6 M HNO{sub 3} with 0.15 M oxalate, the solubility of Gd at 10

  12. Oligosaccharide-based Surfactant/Citric Acid Buffer System Stabilizes Lactate Dehydrogenase during Freeze-drying and Storage without the Addition of Natural Sugar.

    PubMed

    Ogawa, Shigesaburo; Kawai, Ryuichiro; Koga, Maito; Asakura, Kouichi; Takahashi, Isao; Osanai, Shuichi

    2016-06-01

    Experiments were conducted to assess the maintenance effects of oligosaccharide-based surfactants on the enzymatic activity of a model protein, lactate dehydrogenase (LDH), during freeze-drying and room temperature storage using the citric acid buffer system. Oligosaccharide-based surfactants, which exhibit a high glass transition temperature (Tg), promoted the eminent retention of enzymatic activity during these protocols, whereas monosaccharide-based surfactants with a low Tg displayed poor performance at high concentration, albeit much better than that of Tween 80 at middle concentration. The increase in the alkyl chain length did not exert positive effects as observed for the maintenance effect during freeze-thawing, but an amphiphilic nature and a glass forming ability were crucial for the effective stabilization at a low excipient concentration during freeze-drying. Even a low oligosaccharide-based surfactant content (0.1 mg mL(-1)) could maintain LDH activity during freeze-drying, but a high surfactant content (1.0 mg mL(-1)) was required to prevent buffer precipitation and retain high LDH activity on storage. Regarding storage, glass formation restricted molecular mobility in the lyophilized matrix, and LDH activity was effectively retained. The present results describe a strategy based on the glass-forming ability of surfactant-type excipients that affords a natural sugar-free formulation or an alternative use for polysorbate-type surfactants.

  13. Optical properties of chitosan in aqueous solution of L- and D-ascorbic acids

    NASA Astrophysics Data System (ADS)

    Malinkina, Olga N.; Shipovskaya, Anna B.; Kazmicheva, Olga F.

    2016-04-01

    The optical properties of aqueous chitosan solutions in L- and D-ascorbic acids were studied by optical rotatory dispersion and spectrophotometry. The specific optical rotation [α] of all chitosan solutions tested was positive, in contrast to aqueous solutions of the ascorbic acid enantiomers, which exhibit an inverse relationship of [α] values. Significant differences in the absolute values of [α] of the chitosan solutions at polymer-acid ratios exceeding the equimolar one were found.

  14. Hexavalent uranium diffusion into soils from concentrated acidic and alkaline solutions

    SciTech Connect

    Tokunaga, Tetsu K.; Wan, Jiamin; Pena, Jasquelin; Sutton, Stephen R.; Newville, Matthew

    2004-03-29

    Uranium contamination of soils and sediments often originates from acidic or alkaline waste sources, with diffusion being a major transport mechanism. Measurements of U(VI) diffusion from initially pH 2 and pH 11 solutions into a slightly alkaline Altamont soil and a neutral Oak Ridge soil were obtained through monitoring uptake from boundary reservoirs and from U concentration profiles within soil columns. The soils provided pH buffering, resulting in diffusion at nearly constant pH. Micro x-ray absorption near edge structure spectra confirmed that U remained in U(VI) forms in all soils. Time trends of U(VI) depletion from reservoirs, and U(VI) concentration profiles within soil columns yielded K{sub d} values consistent with those determined in batch tests at similar concentrations ({approx} 1 mM), and much lower than values for sorption at much lower concentrations (nM to {mu}M). These results show that U(VI) transport at high concentrations can be relatively fast at non-neutral pH, with negligible surface diffusion, because of weak sorption.

  15. Abscisic Acid Movement into the Apoplastic solution of Water-Stressed Cotton Leaves

    PubMed Central

    Hartung, Wolfram; Radin, John W.; Hendrix, Donald L.

    1988-01-01

    Leaves of cotton (Gossypium hirsutum L.) were subjected to overpressures in a pressure chamber, and the exuded sap was collected and analyzed. The exudate contained low concentrations of solutes that were abundant in total leaf extracts, and photosynthetic rates and stomatal conductance were completely unaffected by a cycle of pressurization and rehydration. These criteria and others indicate that the experimental techniques inflicted no damage upon the leaf cells. The pH and abscisic acid (ABA) content of the apoplastic fluid both increased greatly with pressure-induced dehydration. Although ABA concentrations did not reach a steady state, the peak levels were above 1 micromolar, an order of magnitude greater than bulk ABA concentrations of the leaf blades. Treatment of leaves with fusicoccin decreased the K+ concentration, greatly reduced the pH rise, and completely eliminated the increase in ABA in the apoplast upon dehydration. When water-stressed leaves were pressurized, the pH of the exuded sap was increased by 0.2 units per 1 megapascal decrease in initial leaf water potential. Buffer capacity of the sap was least in the pH range of interest (6.5-7.5), allowing extremely small changes in H+ fluxes to create large changes in apoplastic pH. The data indicate that dehydration causes large changes in apoplastic pH, perhaps by effects on ATPases; the altered pH then enhances the release of ABA from mesophyll cells into the apoplastic fluid. PMID:16666007

  16. Passive and transpassive anodic behavior of chalcopyrite in acid solutions

    NASA Astrophysics Data System (ADS)

    Warren, G. W.; Wadsworth, M. E.; El-Raghy, S. M.

    1992-01-01

    The electrochemical oxidation of CuFeS2 in various acid solutions was studied using electrodes made from massive samples. The primary techniques employed were potentiodynamic polarization and constant potential experiments supplemented by capacitance measurements. It was the purpose of this study to investigate the behavior of: (1) several sources of CuFeS2 in H2SO4 electrolytes, and (2) a single source of CuFeS2 in various dilute acids. Electrochemical characterization of CuFeS2 from various locations was performed in 1 M H2SO4 which showed significant differences in their behavior. All samples exhibited passive-like response during anodic polarization. The current density in this passive region was reproducible and showed differences of up to two orders of magnitude between samples from different sources which has been attributed mainly to the presence of impurities in some of the samples. During anodic polarization CuFeS2 was found to be sensitive to pH at higher potential, but insensitive at low potential in sulfate solution. In addition, current decay measurements at constant potential in the low potential-passive region were found to follow the Sato-Cohen (logarithmic) model for solid film formation. Based on current and mass balance measurements, two intermediate sulfide phases appeared to form in the sequence CuFeS2 → S, → S2. At higher potentials, in the transpassive region, the observed increase in current is compatible with the decomposition of water to form chemisorbed oxygen which releases copper and forms sulfate ions.

  17. Passive and transpassive anodic behavior of chalcopyrite in acid solutions

    NASA Astrophysics Data System (ADS)

    Warren, G. W.; Wadsworth, M. E.; El-Raghy, S. M.

    1982-12-01

    The electrochemical oxidation of CuFeS2 in various acid solutions was studied using electrodes made from massive samples. The primary techniques employed were potentiodynamic polarization and constant potential experiments supplemented by capacitance measurements. It was the purpose of this study to investigate the behavior of: (1) several sources of CuFeS2 in H2SO4 electrolytes, and (2) a single source of CuFeS2 in various dilute acids. Electrochemical characterization of CuFeS2 from various locations was performed in 1 M H2SO4 which showed significant differences in their behavior. All samples exhibited passive-like response during anodic polarization. The current density in this passive region was reproducible and showed differences of up to two orders of magnitude between samples from different sources which has been attributed mainly to the presence of impurities in some of the samples. During anodic polarization CuFeS2 was found to be sensitive to pH at higher potential, but insensitive at low potential in sulfate solution. In addition, current decay measurements at constant potential in the low potential-passive region were found to follow the Sato-Cohen (logarithmic) model for solid film formation. Based on current and mass balance measurements, two intermediate sulfide phases appeared to form in the sequence CuFeS2→S1→S2. At higher potentials, in the transpassive region, the observed increase in current is compatible with the decomposition of water to form chemisorbed oxygen which releases copper and forms sulfate ions.

  18. Buffering agents modify the hydration landscape at charged interfaces.

    PubMed

    Trewby, William; Livesey, Duncan; Voïtchovsky, Kislon

    2016-03-01

    Buffering agents are widely used to stabilise the pH of solutions in soft matter and biological sciences. They are typically composed of weak acids and bases mixed in an aqueous solution, and can interact electrostatically with charged surfaces such as biomembranes. Buffers can induce protein aggregation and structural modification of soft interfaces, but a molecular-level picture is still lacking. Here we use high-resolution atomic force microscopy to investigate the effect of five commonly used buffers, namely 4-(2-hydroxyethyl)piperazine-1-ethanesulfonic acid (HEPES), 2-(N-morpholino)ethanesulfonic acid (MES), monosodium phosphate, saline sodium citrate (SSC) and tris(hydroxymethyl)aminomethane (Tris) on the hydration landscape of Muscovite mica in solution. Mica is an ideal model substrate due to its negative surface charge and identical lattice parameter when compared with gel-phase lipid bilayers. We show that buffer molecules can produce cohesive aggregates spanning over tens of nanometres of the interface. SSC, Tris and monosodium phosphate tend to create an amorphous mesh layer several molecules thick and with no preferential ordering. In contrast, MES and HEPES adopt epitaxial arrangements commensurate with the underlying mica lattice, suggesting that they offer the most suitable solution for high-resolution studies. To confirm that this effect persisted in biologically-relevant interfaces, the experiments were repeated on a silica-supported lipid bilayer. Similar trends were observed for this system using atomic force microscopy as well as ellipsometry. The effect of the buffering agents can be mitigated by the inclusion of salt which helps displace them from the interface. PMID:26837938

  19. Solubility of xenon in amino-acid solutions. II. Nine less-soluble amino acids

    NASA Astrophysics Data System (ADS)

    Kennan, Richard P.; Himm, Jeffrey F.; Pollack, Gerald L.

    1988-05-01

    Ostwald solubility (L) of xenon gas, as the radioisotope 133Xe, has been measured as a function of solute concentration, at 25.0 °C, in aqueous solutions of nine amino acids. The amino-acid concentrations investigated covered much of their solubility ranges in water, viz., asparagine monohydrate (0-0.19 M), cysteine (0-1.16 M), glutamine (0-0.22 M), histidine (0-0.26 M), isoleucine (0-0.19 M), methionine (0-0.22 M), serine (0-0.38 M), threonine (0-1.4 M), and valine (0-0.34 M). We have previously reported solubility results for aqueous solutions of six other, generally more soluble, amino acids (alanine, arginine, glycine, hydroxyproline, lysine, and proline), of sucrose and sodium chloride. In general, L decreases approximately linearly with increasing solute concentration in these solutions. If we postulate that the observed decreases in gas solubility are due to hydration, the results under some assumptions can be used to calculate hydration numbers (H), i.e., the number of H2O molecules associated with each amino-acid solute molecule. The average values of hydration number (H¯) obtained at 25.0 °C are 15.3±1.5 for asparagine, 6.8±0.3 for cysteine, 11.5±1.1 for glutamine, 7.3±0.7 for histidine, 5.9±0.4 for isoleucine, 10.6±0.8 for methionine, 11.2±1.3 for serine, 7.7± 1.0 for threonine, and 6.6±0.6 for valine. We have also measured the temperature dependence of solubility L(T) from 5-40 °C for arginine, glycine, and proline, and obtained hydration numbers H¯(T) in this range. Between 25-40 °C, arginine has an H¯ near zero. This may be evidence for an attractive interaction between xenon and arginine molecules in aqueous solution.

  20. An automated system for monitoring and regulating the pH of bicarbonate buffers.

    PubMed

    Garbacz, Grzegorz; Kołodziej, Bartosz; Koziolek, Mirko; Weitschies, Werner; Klein, Sandra

    2013-06-01

    The bicarbonate buffer is considered as the most biorelevant buffer system for the simulation of intestinal conditions. However, its use in dissolution testing of solid oral dosage forms is very limited. The reason for this is the thermodynamic instability of the solution containing hydrogen carbonate ions and carbonic acid. The spontaneous loss of carbon dioxide (CO(2)) from the solution results in an uncontrolled increase of the pH. In order to maintain the pH on the desired level, either a CO(2) loss must be completely avoided or the escaped CO(2) has to be replaced by quantitative substitution, i.e. feeding the solution with the respective amount of gas, which re-acidifies the buffer after dissociation. The present work aimed at the development of a device enabling an automatic pH monitoring and regulation of hydrogen carbonate buffers during dissolution tests.

  1. Buffer standards for the physiological pH of the zwitterionic compound of 3-(N-morpholino)propanesulfonic acid (MOPS) from T = (278.15 to 328.15) K.

    PubMed

    Roy, Lakshmi N; Roy, Rabindra N; Allen, Kathleen A; Mehrhoff, Casey J; Henson, Isaac B; Stegner, Jessica M

    2012-04-01

    This paper reports the pH values of five NaCl-free buffer solutions and eleven buffer compositions containing NaCl at I = 0.16 mol·kg(-1). Conventional pa(H) values are reported for sixteen buffer solutions with and without NaCl salt. The operational pH values have been calculated for five buffer solutions and are recommended as pH standards at T = (298.15 and 310.15) K after correcting the liquid junction potentials. For buffer solutions with the composition m(1) = 0.04 mol·kg(-1), m(2) = 0.08 mol·kg(-1), m(3) = 0.08 mol·kg(-1) at I = 0.16 mol·kg(-1), the pH at 310.15 K is 7.269, which is close to 7.407, the pH of blood serum. It is recommended as a pH standard for biological specimens.

  2. Buffer standards for the physiological pH of the zwitterionic compound of 3-(N-morpholino)propanesulfonic acid (MOPS) from T = (278.15 to 328.15) K

    PubMed Central

    Roy, Lakshmi N.; Roy, Rabindra N.; Allen, Kathleen A.; Mehrhoff, Casey J.; Henson, Isaac B.; Stegner, Jessica M.

    2011-01-01

    This paper reports the pH values of five NaCl-free buffer solutions and eleven buffer compositions containing NaCl at I = 0.16 mol·kg−1. Conventional paH values are reported for sixteen buffer solutions with and without NaCl salt. The operational pH values have been calculated for five buffer solutions and are recommended as pH standards at T = (298.15 and 310.15) K after correcting the liquid junction potentials. For buffer solutions with the composition m1 = 0.04 mol·kg−1, m2 = 0.08 mol·kg−1, m3 = 0.08 mol·kg−1 at I = 0.16 mol·kg−1, the pH at 310.15 K is 7.269, which is close to 7.407, the pH of blood serum. It is recommended as a pH standard for biological specimens. PMID:22247568

  3. Solution structures of europium(III) complexes of ethylenediaminetetraacetic acid

    SciTech Connect

    Latva, M.; Kankara, J.; Haapakka, K.

    1996-04-01

    Coordination of ethylenediaminetetraacetic acid (EDTA) with europium(III) has been studied at different concentrations in solution using {sup 7}F{sub 0}{yields}{sup 5}D{sub 0} excitation spectroscopy and excited-state lifetime measurements. EDTA forms with Eu(III) ion three different species in equimolar solutions at room temperature. At low pH values EuEDTAH is formed and at higher pH values than 1.5 two EuEDTA{sup -} complexes, which differ from each other with one water molecule in the first coordination sphere of the Eu(III) ion, total coordination number and coordination geometry, are also formed. When the concentration of EDTA is higher than the concentration of Eu(III), an EuEDTA(EDTAH){sup 4-} species where the second EDTA is weakly coordinated to EuEDTA{sup -}, is formed. If the concentration of Eu(III) ion is higher than EDTA, the extra Eu(III) ions associate with EuEDTA{sup -} and link to one of the carboxylate groups of EDTA thus causing a shortening of the excited-state lifetime of the EuEDTA{sup -} complex.

  4. [Impact of a simultaneous application of anionic salts and rumen buffer on acid-base-balance and mineral metabolism in dairy cows].

    PubMed

    Gelfert, Carl-Christian; Hauser, Simone; Löptien, Antje; Montag, Nicole; Passmann, Mareike; Baumgartner, Walter; Staufenbiel, Rudolf

    2006-01-01

    In this study, the influence of simultaneous application of anionic salts (AS) and rumen buffer (RB) on the metabolism of dairy cows was examined. Eleven rumen fistulated, non-pregnant and non-lactating dairy cows received equal amounts of one AS (CaCl2 or CaSO4) and one RB (NaHCO3 or KHCO3) via rumen cannula during feeding time over a period of eight days. Before the first application of AS and RB and on day eight of the treatment period, blood, urine and rumen fluid samples were taken. The following parameters were measured: whole blood: pH, base excess, bicarbonate; serum: sodium, potassium, chloride, calcium; urine: pH, net acid base excretion, sodium, potassium, chloride, calcium; rumen fluid: pH. The changes of each parameter were compared via ANOVA. The changes in acid-base balance on day eight were very small, although significant. But p-values showed that the statistical evidence was low. The most changes occurred when NaHCO3 was fed in combination with one of the AS used. In this case a small acidogenic load was seen in blood (p < 0.05), and calcium concentrations increased slightly (p < 0.05). No alkalotic reaction could be detected when any combination of AS and RB were given to the cows. Simultaneous application of AS and RB results in a loss of effectivity of AS. Neither an adequate acidification of blood nor an activation of calcium metabolism occurred. In feed ration for cows in the last weeks of pregnancy, rumen buffer must not be fed, if anionic salts are given for prevention of parturient paresis.

  5. Effects of amino acid sequence, buffers, and ionic strength on the rate and mechanism of deamidation of asparagine residues in small peptides.

    PubMed

    Tyler-Cross, R; Schirch, V

    1991-11-25

    The nonenzymatic rates of deamidation of Asn residues in a series of pentapeptides with the sequences VSNXV and VXNSV, where X is one of 10 different amino acids, were determined at neutral, alkaline, and acid pH values. The results demonstrate that in neutral and alkaline solutions the amino acid residue on the amino side of the Asn had little or no effect on the rate of deamidation regardless of its charge or size. The group on the carboxyl side of Asn affected the rate of deamidation significantly. Increasing size and branching in the side chain of this residue decreased the rate of deamidation by as much as 70-fold compared to glycine in the N-G sequence, which had the greatest rate of deamidation. In acidic solution, the rate of deamidation of the Asn residue was not affected by the amino acid sequence of the peptide. The products for each deamidation reaction were tested for the formation of isoAsp residues. In neutral and alkaline solutions, all products showed that the isoAsp:Asp peptide products were formed in about a 3:1 ratio. In acidic solution, the Asp peptide was the only deamidation product formed. All peptides in which a Ser residue follows the Asn residue were found to undergo a peptide cleavage reaction in neutral and alkaline solutions, yielding a tripeptide and a dipeptide. The rate of the cleavage reaction was about 10% of the rate of the deamidation pathway at neutral and alkaline pH values. The rates of deamidation of Asn residues in the peptides studied were not affected by ionic strength, and were not specific base catalyzed. General base catalysis was observed for small bases like ammonia. A model for the deamidation reaction is proposed to account for the observed effects. PMID:1939272

  6. Uptake of ozone to mixed sodium bromide/ citric acid solutions

    NASA Astrophysics Data System (ADS)

    Lee, Ming-Tao; Steimle, Emilie; Bartels-Rausch, Thorsten; Kato, Shunsuke; Lampimäki, Markus; Brown, Matthew; van Bokhoven, Jeroen; Nolting, Frithjof; Kleibert, Armin; Türler, Andreas; Ammann, Markus

    2013-04-01

    Sea-salt solution - air interfaces play an important role in the chemistry of the marine boundary layer. The reaction of ozone (O3) with bromide is of interest in the context of formation of photolabile halogens (Br2, BrCl) in the marine boundary layer. Recent experiments have suggested that the bromide oxidation rate is related to the surface concentration of bromide [1] and inversely related to the gas phase concentration of O3, an indication for a precursor mediated reaction at the surface [2]. So far, the effect of organics (such as those occurring at the ocean surface or in marine aerosols) on the reaction of O3 with bromide aerosols has not been studied yet. In our study we investigate the uptake kinetics of O3 to a mixed solution of sodium bromide (NaBr) and citric acid (CA), which represents highly oxidized organic compounds present in the environment, with a well-established coated wall flow tube technique, which leads to exposure of the film to O3 allowing the heterogeneous reactions to take place and the loss of O3 being measured. The results indicate that the uptake of O3 to the films with the higher bromide concentrations (0.34M and 4M) is independent of the gas phase concentration and roughly consistent with uptake limited by reaction in the bulk. For the lower bromide concentration (84mM), however, we observe a trend of the uptake coefficient to decrease with increasing O3 concentration, indicating an increasing importance of a surface reaction. In an attempt to constrain the kinetic data, we employed X-ray photoelectron spectroscopy (XPS) to get insight into the surface composition of the aqueous solution - air interface. Previous XPS studies have shown that halide ion concentrations are enhanced at the aqueous solution air interface [3-4], which likely promotes the surface reactions of bromide or iodide with O3. A first XPS study of ternary solutions of KI with butanol indicated the importance of specific interactions of the cation with the alcohol

  7. Aerosol pH buffering in the southeastern US: Fine particles remain highly acidic despite large reductions in sulfate

    NASA Astrophysics Data System (ADS)

    Weber, R. J.; Guo, H.; Russell, A. G.; Nenes, A.

    2015-12-01

    pH is a critical aerosol property that impacts many atmospheric processes, including biogenic secondary organic aerosol formation, gas-particle phase partitioning, and mineral dust or redox metal mobilization. Particle pH has also been linked to adverse health effects. Using a comprehensive data set from the Southern Oxidant and Aerosol Study (SOAS) as the basis for thermodynamic modeling, we have shown that particles are currently highly acidic in the southeastern US, with pH between 0 and 2. Sulfate and ammonium are the main acid-base components that determine particle pH in this region, however they have different sources and their concentrations are changing. Over 15 years of network data show that sulfur dioxide emission reductions have resulted in a roughly 70 percent decrease in sulfate, whereas ammonia emissions, mainly link to agricultural activities, have been largely steady, as have gas phase ammonia concentrations. This has led to the view that particles are becoming more neutralized. However, sensitivity analysis, based on thermodynamic modeling, to changing sulfate concentrations indicates that particles have remained highly acidic over the past decade, despite the large reductions in sulfate. Furthermore, anticipated continued reductions of sulfate and relatively constant ammonia emissions into the future will not significantly change particle pH until sulfate drops to clean continental background levels. The result reshapes our expectation of future particle pH and implies that atmospheric processes and adverse health effects linked to particle acidity will remain unchanged for some time into the future.

  8. Interaction of trace elements in acid mine drainage solution with humic acid.

    PubMed

    Suteerapataranon, Siripat; Bouby, Muriel; Geckeis, Horst; Fanghänel, Thomas; Grudpan, Kate

    2006-06-01

    The release of metal ions from a coal mining tailing area, Lamphun, Northern Thailand, is studied by leaching tests. Considerable amounts of Mn, Fe, Al, Ni and Co are dissolved in both simulated rain water (pH 4) and 10 mg L(-1) humic acid (HA) solution (Aldrich humic acid, pH 7). Due to the presence of oxidizing pyrite and sulfide minerals, the pH in both leachates decreases down to approximately 3 combined with high sulfate concentrations typical to acid mine drainage (AMD) water composition. Interaction of the acidic leachates upon mixing with ground- and surface water containing natural organic matter is simulated by subsequent dilution (1:100; 1:200; 1:300; 1:500) with a 10 mg L(-1) HA solution (ionic strength: 10(-3) mol L(-1)). Combining asymmetric flow field-flow fractionation (AsFlFFF) with UV/Vis and ICP-MS detection allows for the investigation of metal ion interaction with HA colloid and colloid size evolution. Formation of colloid aggregates is observed by filtration and AsFlFFF depending on the degree of the dilution. While the average HA size is initially found to be 2 nm, metal-HA complexes are always found to be larger. Such observation is attributed to a metal induced HA agglomeration, which is found even at low coverage of HA functional groups with metal ions. Increasing the metal ion to HA ratio, the HA bound metal ions and the HA entities are growing in size from <3 to >450 nm. At high metal ion to HA ratios, precipitation of FeOOH phases and HA agglomeration due to colloid charge neutralization by complete saturation of HA complexing sites are responsible for the fact that most of Fe and Al precipitate and are found in a size fraction >450 nm. In the more diluted solutions, HA is more relevant as a carrier for metal ion mobilization.

  9. Volumetric and UV absorption studies on understanding the solvation behavior of polyhydroxy solutes in l-ascorbic acid(aq) solutions at T=(288.15 to 318.15)K.

    PubMed

    Banipal, Parampaul K; Sharma, Mousmee; Banipal, Tarlok S

    2016-02-01

    Thermodynamic and spectroscopic data characterizing the solvation behavior of polyhydroxy compounds are in demand to get better understanding about the mechanisms of taste chemoreception, protein stabilization, etc. Apparent molar volumes for monosaccharides, disaccharides, derivatives, and polyols in (0.05, 0.15, 0.25 and 0.35) mol kg(-1) aqueous solutions of l-ascorbic acid have been determined from density data measured at (288.15, 298.15, 308.15 and 318.15)K under atmospheric pressure. Standard partial molar volumes at infinite-dilution and corresponding volumes of transfer of solutes from water to L-ascorbic acid(aq) have been calculated. Interaction coefficients and standard partial molar expansibilities have also been evaluated. The basic taste quality of studied solutes has been assessed from apparent massic volumes. UV absorption studies support the interactions between solutes and L-ascorbic acid. Influence of pH variation was taken into consideration while evaluating chemical behavior and stability of L-ascorbic acid in aqueous and buffer solutions.

  10. Volumetric and UV absorption studies on understanding the solvation behavior of polyhydroxy solutes in l-ascorbic acid(aq) solutions at T=(288.15 to 318.15)K.

    PubMed

    Banipal, Parampaul K; Sharma, Mousmee; Banipal, Tarlok S

    2016-02-01

    Thermodynamic and spectroscopic data characterizing the solvation behavior of polyhydroxy compounds are in demand to get better understanding about the mechanisms of taste chemoreception, protein stabilization, etc. Apparent molar volumes for monosaccharides, disaccharides, derivatives, and polyols in (0.05, 0.15, 0.25 and 0.35) mol kg(-1) aqueous solutions of l-ascorbic acid have been determined from density data measured at (288.15, 298.15, 308.15 and 318.15)K under atmospheric pressure. Standard partial molar volumes at infinite-dilution and corresponding volumes of transfer of solutes from water to L-ascorbic acid(aq) have been calculated. Interaction coefficients and standard partial molar expansibilities have also been evaluated. The basic taste quality of studied solutes has been assessed from apparent massic volumes. UV absorption studies support the interactions between solutes and L-ascorbic acid. Influence of pH variation was taken into consideration while evaluating chemical behavior and stability of L-ascorbic acid in aqueous and buffer solutions. PMID:26304409

  11. Release of nitrous acid and nitrogen dioxide from nitrate photolysis in acidic aqueous solutions.

    PubMed

    Scharko, Nicole K; Berke, Andrew E; Raff, Jonathan D

    2014-10-21

    Nitrate (NO3(-)) is an abundant component of aerosols, boundary layer surface films, and surface water. Photolysis of NO3(-) leads to NO2 and HONO, both of which play important roles in tropospheric ozone and OH production. Field and laboratory studies suggest that NO3¯ photochemistry is a more important source of HONO than once thought, although a mechanistic understanding of the variables controlling this process is lacking. We present results of cavity-enhanced absorption spectroscopy measurements of NO2 and HONO emitted during photodegradation of aqueous NO3(-) under acidic conditions. Nitrous acid is formed in higher quantities at pH 2-4 than expected based on consideration of primary photochemical channels alone. Both experimental and modeled results indicate that the additional HONO is not due to enhanced NO3(-) absorption cross sections or effective quantum yields, but rather to secondary reactions of NO2 in solution. We find that NO2 is more efficiently hydrolyzed in solution when it is generated in situ during NO3(-) photolysis than for the heterogeneous system where mass transfer of gaseous NO2 into bulk solution is prohibitively slow. The presence of nonchromophoric OH scavengers that are naturally present in the environment increases HONO production 4-fold, and therefore play an important role in enhancing daytime HONO formation from NO3(-) photochemistry.

  12. Pyrroloquinoline quinone (PQQ) is reduced to pyrroloquinoline quinol (PQQH2) by vitamin C, and PQQH2 produced is recycled to PQQ by air oxidation in buffer solution at pH 7.4.

    PubMed

    Mukai, Kazuo; Ouchi, Aya; Nagaoka, Shin-ichi; Nakano, Masahiko; Ikemoto, Kazuto

    2015-01-01

    Measurements of the reaction of sodium salt of pyrroloquinoline quinone (PQQNa2) with vitamin C (Vit C) were performed in phosphate-buffered solution (pH 7.4) at 25 °C under nitrogen atmosphere, using UV-vis spectrophotometry. The absorption spectrum of PQQNa2 decreased in intensity due to the reaction with Vit C and was changed to that of pyrroloquinoline quinol (PQQH2, a reduced form of PQQ). One molecule of PQQ was reduced by two molecules of Vit C producing a molecule of PQQH2 in the buffer solution. PQQH2, thus produced, was recycled to PQQ due to air oxidation. PQQ and Vit C coexist in many biological systems, such as vegetables, fruits, as well as in human tissues. The results obtained suggest that PQQ is reduced by Vit C and functions as an antioxidant in biological systems, because it has been reported that PQQH2 shows very high free-radical scavenging and singlet-oxygen quenching activities in buffer solutions.

  13. An improvement to the ligand optimisation method (LOM) for measuring the apparent dissociation constant and ligand purity in Ca2+ and Mg2+ buffer solutions.

    PubMed

    McGuigan, John A S; Kay, James W; Elder, Hugh Y

    2014-01-01

    In Ca(2+)/Mg(2+) buffers the calculated ionised concentrations ([X(2+)]) can vary by up to a factor of seven. Since there are no defined standards it is impossible to check calculated [X(2+)], making measurement essential. The ligand optimisation method (LOM) is an accurate method to measure [X(2+)] in Ca(2+)/Mg(2+) buffers; independent estimation of ligand purity extends the method to pK(/) < 4. To simplify calculation, Excel programs ALE and AEC were compiled for LOM and its extension. This paper demonstrates that the slope of the electrode in the pX range 2.000-3.301 deviates from Nernstian behaviour as it depends on the value of the lumped interference, Σ. ALE was modified to include this effect; this modified program SALE, and the programs ALE and AEC were used on simulated data for Ca(2+)-EGTA and Mg(2+)-ATP buffers, to calculate electrode and buffer characteristics as a function of Σ. Ca(2+)-electrodes have a Σ < 10(-6) mol/l and there was no difference amongst the three methods. The Σ for Mg(2+)-electrodes lies between 10(-5) and 1.5 (∗) 10(-5) mol/l and calculated [Mg(2+)] with ALE were around 3% less than the true value. SALE and AEC correctly predicted [Mg(2+)]. SALE was used to recalculate K(/) and pK(/) on measured data for Ca(2+)-EGTA and Mg(2+)-EDTA buffers. These results demonstrated that it is pK(/) that is normally distributed. Until defined standards are available, [X(2+)] in Ca(2+)/Mg(2+) buffers have to be measured. The most appropriate method is to use Ca(2+)/Mg(2) electrodes combined with the Excel programs SALE or AEC.

  14. Adaptively biased sequential importance sampling for rare events in reaction networks with comparison to exact solutions from finite buffer dCME method

    PubMed Central

    Cao, Youfang; Liang, Jie

    2013-01-01

    Critical events that occur rarely in biological processes are of great importance, but are challenging to study using Monte Carlo simulation. By introducing biases to reaction selection and reaction rates, weighted stochastic simulation algorithms based on importance sampling allow rare events to be sampled more effectively. However, existing methods do not address the important issue of barrier crossing, which often arises from multistable networks and systems with complex probability landscape. In addition, the proliferation of parameters and the associated computing cost pose significant problems. Here we introduce a general theoretical framework for obtaining optimized biases in sampling individual reactions for estimating probabilities of rare events. We further describe a practical algorithm called adaptively biased sequential importance sampling (ABSIS) method for efficient probability estimation. By adopting a look-ahead strategy and by enumerating short paths from the current state, we estimate the reaction-specific and state-specific forward and backward moving probabilities of the system, which are then used to bias reaction selections. The ABSIS algorithm can automatically detect barrier-crossing regions, and can adjust bias adaptively at different steps of the sampling process, with bias determined by the outcome of exhaustively generated short paths. In addition, there are only two bias parameters to be determined, regardless of the number of the reactions and the complexity of the network. We have applied the ABSIS method to four biochemical networks: the birth-death process, the reversible isomerization, the bistable Schlögl model, and the enzymatic futile cycle model. For comparison, we have also applied the finite buffer discrete chemical master equation (dCME) method recently developed to obtain exact numerical solutions of the underlying discrete chemical master equations of these problems. This allows us to assess sampling results objectively

  15. Large-scale production of anhydrous nitric acid and nitric acid solutions of dinitrogen pentoxide

    DOEpatents

    Harrar, Jackson E.; Quong, Roland; Rigdon, Lester P.; McGuire, Raymond R.

    2001-01-01

    A method and apparatus are disclosed for a large scale, electrochemical production of anhydrous nitric acid and N.sub.2 O.sub.5. The method includes oxidizing a solution of N.sub.2 O.sub.4 /aqueous-HNO.sub.3 at the anode, while reducing aqueous HNO.sub.3 at the cathode, in a flow electrolyzer constructed of special materials. N.sub.2 O.sub.4 is produced at the cathode and may be separated and recycled as a feedstock for use in the anolyte. The process is controlled by regulating the electrolysis current until the desired products are obtained. The chemical compositions of the anolyte and catholyte are monitored by measurement of the solution density and the concentrations of N.sub.2 O.sub.4.

  16. A pulse radiolysis study of salicylic acid and 5-sulpho-salicylic acid in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Kishore, Kamal; Mukherjee, T.

    2006-01-01

    Reactions of H, OH, eaq- and some one-electron oxidants have been studied with salicylic acid and 5-sulpho-salicylic acid in aqueous solutions. Rate constants for the reaction of eaq- with these compounds were of the order of 10 9 dm 3 mol -1 s -1 and this reaction led to the formation of reducing radicals which could transfer electron to methyl viologen. Other one-electron reductants were not able to reduce these compounds. OH radicals reacted with these compounds by addition pathway with very high rate constants (>10 10 dm 3 mol -1 s -1) while O rad - radical anions could oxidize these molecules to give phenoxyl type of radicals. Amongst the one-electron oxidants, only N 3rad and SO 4rad - could oxidize salicylic acid while 5-sulpho-salicylic acid could be oxidized only by SO 4- radicals indicating that while one-electron reduction potential for semi-oxidized SA may be<1.33 V vs. NHE (the E o1 for N 3rad radical), it is more than 1.33 V vs. NHE for semi-oxidized SSA species.

  17. Retention of ionisable compounds on high-performance liquid chromatography XVII. Estimation of the pH variation of aqueous buffers with the change of the methanol fraction of the mobile phase.

    PubMed

    Subirats, Xavier; Bosch, Elisabeth; Rosés, Martí

    2007-01-01

    The use of methanol-aqueous buffer mobile phases in HPLC is a common election when performing chromatographic separations of ionisable analytes. The addition of methanol to the aqueous buffer to prepare such a mobile phase changes the buffer capacity and the pH of the solution. In the present work, the variation of these buffer properties is studied for acetic acid-acetate, phosphoric acid-dihydrogenphosphate-hydrogenphosphate, citric acid-dihydrogencitrate-hydrogencitrate-citrate, and ammonium-ammonia buffers. It is well established that the pH change of the buffers depends on the initial concentration and aqueous pH of the buffer, on the percentage of methanol added, and on the particular buffer used. The proposed equations allow the pH estimation of methanol-water buffered mobile phases up to 80% in volume of organic modifier from initial aqueous buffer pH and buffer concentration (before adding methanol) between 0.001 and 0.01 mol L(-1). From both the estimated pH values of the mobile phase and the estimated pKa of the ionisable analytes, it is possible to predict the degree of ionisation of the analytes and therefore, the interpretation of acid-base analytes behaviour in a particular methanol-water buffered mobile phase.

  18. Uptake of Hypobromous Acid (HOBr) by Aqueous Sulfuric Acid Solutions: Low-Temperature Solubility and Reaction

    NASA Technical Reports Server (NTRS)

    Iraci, Laura T.; Michelsen, Rebecca R.; Ashbourn, Samatha F. M.; Rammer, Thomas A.; Golden, David M.

    2005-01-01

    Hypobromous acid (HOBr) is a key species linking inorganic bromine to the chlorine and odd hydrogen chemical families. We have measured the solubility of HOBr in 45 - 70 wt% sulfuric acid solutions representative of upper tropospheric and lower stratospheric aerosol composition. Over the temperature range 201 - 252 K, HOBr is quite soluble in sulfuric acid, with an effective Henry's law coefficient, H* = 10(exp 4) - 10(exp 7) mol/L/atm. H* is inversely dependent on temperature, with Delta H = -46.2 kJ/mol and Delta S = -106.2 J/mol/K for 55 - 70 wt% H2SO4 solutions. Our study includes temperatures which overlap both previous measurements of HOBr solubility. For uptake into aqueous 45 wt% H2SO4, the solubility can be described by log H* = 3665/T - 10.63. For 55 - 70 wt% H2SO4, log H* = 2412/T - 5.55. At temperatures colder than approx. 213 K, the solubility of HOBr in 45 wt% H2SO4 is noticeably larger than in 70 wt% H2SO4. The solubility of HOBr is comparable to that of HBr, indicating that upper tropospheric and lower stratospheric aerosols should contain equilibrium concentrations of HOBr which equal or exceed those of HBr. Our measurements indicate chemical reaction of HOBr upon uptake into aqueous sulfuric acid in the presence of other brominated gases followed by evolution of gaseous products including Br2O and Br2, particularly at 70 wt% H2SO4.

  19. Extraction equilibrium of indium(III) from nitric acid solutions by di(2-ethylhexyl)phosphoric acid dissolved in kerosene.

    PubMed

    Tsai, Hung-Sheng; Tsai, Teh-Hua

    2012-01-04

    The extraction equilibrium of indium(III) from a nitric acid solution using di(2-ethylhexyl) phosphoric acid (D2EHPA) as an acidic extractant of organophosphorus compounds dissolved in kerosene was studied. By graphical and numerical analysis, the compositions of indium-D2EHPA complexes in organic phase and stoichiometry of the extraction reaction were examined. Nitric acid solutions with various indium concentrations at 25 °C were used to obtain the equilibrium constant of InR₃ in the organic phase. The experimental results showed that the extraction distribution ratios of indium(III) between the organic phase and the aqueous solution increased when either the pH value of the aqueous solution and/or the concentration of the organic phase extractant increased. Finally, the recovery efficiency of indium(III) in nitric acid was measured.

  20. Unsaturated fatty acids in alkane solution: adsorption to steel surfaces.

    PubMed

    Lundgren, Sarah M; Persson, Karin; Mueller, Gregor; Kronberg, Bengt; Clarke, Jim; Chtaib, Mohammed; Claesson, Per M

    2007-10-01

    The adsorption of the unsaturated fatty acids oleic, linoleic, and linolenic acid on steel surfaces has been investigated by means of a quartz crystal microbalance (QCM). Two different solvents were used, n-hexadecane and its highly branched isomer, viz., 2,2,4,4,6,8,8-heptamethylnonane. The area occupied per molecule of oleic acid at 1 wt % corresponds to what is needed for adsorption parallel to the surface. At the same concentration, the adsorbed amount of linoleic acid and linolenic acid indicates that they adsorb in multilayers. The chemisorbed amount estimated from static secondary ion mass spectroscopy (SIMS) measurements was found to be similar for the three unsaturated fatty acids. In the case of linolenic acid, it was found that the presence of water significantly alters the adsorption, most likely because of the precipitation of fatty acid/water aggregates. Furthermore, static SIMS results indicate that the amount of water used here inhibits the chemisorption of linolenic acid.

  1. Evaluation of amine inhibitors for suitability as crevice buffering agents. Final report

    SciTech Connect

    Jayaweera, P.; Hettiarachchi, S.

    1994-03-01

    This report describes the results of a research effort to evaluate the suitability of some selected amines and amino acids as a crevice-buffering agents in pressurized water reactor (PWR) steam generators. The amines may be useful for buffering acid crevices, and the amino acids, because they contain both acidic and basic groups, may be useful for acidic and caustic crevices. Five commercially available amines and two amino acids were studied during this research. The study involved (1) the hydrolysis of these commercially available amines and amino acids, including measurement of their kinetics of decomposition, in simulated steam generator bulk water at 290 C, and (2) determination of their thermal stability in a simulated crevice environment. The study showed that, although the high-molecular-weight amines undergo hydrothermal decomposition, they have a better buffering capacity than their low-molecular-weight counterparts at 290 C. The amines provide effective crevice buffering by increasing the pH of the crevice solution by as much as 2.84 and to 4.24 units in the experimental setup used in this program. It was concluded that polyamines provide excellent buffering of the simulated crevice environment at 290 C and morpholine remains the best low-molecular-weight amine investigated. However, detailed volatility studies of the amines were not considered in this work. Such data would be needed before in-plant testing to ensure that the amines can concentrate in steam generator crevices to the levels assumed in this study.

  2. Dissolution reaction and surface iron speciation of UICC crocidolite in buffered solution at pH 7.4: A combined ICP-OES, XPS and TEM investigation

    NASA Astrophysics Data System (ADS)

    Pacella, Alessandro; Fantauzzi, Marzia; Turci, Francesco; Cremisini, Carlo; Montereali, Maria Rita; Nardi, Elisa; Atzei, Davide; Rossi, Antonella; Andreozzi, Giovanni B.

    2014-02-01

    The dissolution reaction and the surface modifications of crocidolite asbestos fibres incubated for 0.5, 1, 24, 48, 168 and 1440 h in a phosphate buffered solution at pH 7.4 with and without hydrogen peroxide were investigated. Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES) was used to monitor the ion release into solution, X-ray Photoelectron Spectroscopy (XPS) was performed to unveil the chemistry of the leached surface, and High Resolution Transmission Electron Microscopy (HR-TEM) was carried out to monitor the structural modifications of the fibres. No significant differences were observed between dissolution experiments carried out with and without H2O2 with the exception of results after the first hour, from which it may be inferred that the dissolution proceeds faster in the presence of H2O2 but only in its very early steps. Congruent mobilization of Si and Mg from crocidolite was observed, increasing with time especially in the range between 1 and 48 h, while Ca decreased after 48 h and Fe was not detected at any incubation time. In the undersaturated conditions (0-48 h), dissolution rate of UICC crocidolite fibres has been estimated to be d(Si)/dt = 0.079 μmol h-1. The fibre surface modification is continuous with time: XPS results showed a regular depletion of Si and Mg and enrichment of Fe along dissolution. The Fe2p3/2 signal on the surface was fitted with four components at 709.0, 710.5, 711.6 and 712.8 eV binding energy values corresponding to: (i) Fe(II)-O and (ii) Fe(III)-O surrounded by oxygen atoms in the silicate structure, (iii) Fe(III)-OOH as a product of the dissolution process, and (iv) Fe in a phosphate precipitate (Fe-P), respectively. The evolution of Fe speciation on the crocidolite surface was followed by integrating the four photoemission peaks, and results showed that the oxidative environment promotes the formation of Fe(III)-O (up to 37% Fetot) and of Fe-P species (up to 16% Fetot), which are found on the fibre

  3. Isothermal heat measurements of TBP-nitric acid solutions

    SciTech Connect

    Smith, J.R.; Cavin, W.S.

    1994-12-16

    Net heats of reaction were measured in an isothermal calorimeter for both single phase (organic) and two phase (organic and aqueous) TBP/HNO{sub 3} reacting solutions at temperatures above 100 C. The oxidation rate constant was determined to be 5.4E-4 min{sup {minus}1} at 110 C for an open ``vented`` system as compared to 1.33 E-3 min{sup {minus}1} in the closed system. The heat released per unit material oxidized was also reduced. The oxidation in both phases was found to be first order in nitric acid and pseudo-zero order in butylnitrate and water. The hydrolysis (esterification) rate constant determined by Nichols` (1.33E-3 min{sup {minus}1}) fit the experimental data from this work well. Forced evaporation of the volatile components by the product gases from oxidation resulted in a cooling mechanism which more than balanced the heat from the oxidation reaction in the two-phased systems. Rate expressions were derived and rate constants determined for both the single and two phase systems. An approximating mathematical model was developed to fit the experimental data and to extrapolate beyond the experimental conditions. This model shows that one foot of ``reacting`` 14.3M HNO{sub 3} aqueous phase solution at 121 C will transport sufficient water to the organic phase to replace evaporative losses, maintaining endothermicity, for organic layers up to 12.2 + 6.0 feet deep. If the pressure in a reacting system is allowed to increase due to insufficient venting the temperature of the organic phase would increase in temperature to reach a new equilibrium. The rate of oxidation would increase not only due to the increase in temperature but also from the increased concentration of dissolved HNO{sub 3} reduction products. Another important factor is that the cooling system described in this work becomes less effective as the total pressure increases. These factors probably contributed to the explosion at Tomsk.

  4. Effect of citric acid on the acidification of artificial pepsin solution for metacercariae isolation from fish.

    PubMed

    Kim, Min-Ki; Pyo, Kyoung-Ho; Hwang, Young-Sang; Chun, Hyang Sook; Park, Ki Hwan; Ko, Seong-Hee; Chai, Jong-Yil; Shin, Eun-Hee

    2013-11-15

    Artificial digestive solution based on pepsin is essential for collecting metacercariae from fish. To promote the enzymatic reactivity of pepsin, the pH of the solution has to be adjusted to pH 1.0-2.0. Hydrochloride (HCl) is usually used for this purpose, but the use of HCl raises safety concerns. The aim of this work was to address the usefulness of citric acid as an alternative for HCl for the acidification of pepsin solution, and to examine its potential to damage metacercariae during in vitro digestion as compared with HCl. Changes in pH after adding 1-9% of citric acid (m/v) to pepsin solution were compared to a 1% HCl (v/v) addition. Digestion of fish muscle was evaluated by measuring released protein concentrations by spectrophotometry. In addition, survival rates of metacercariae in pepsin solution were determined at different citric acid concentrations and were compared that of with 1% HCl. The present study shows that addition of citric acid reduced the pH of pepsin solutions to the required level. Addition of more than 5% of citric acid resulted in the effective digestion of fish muscle over 3h in vitro, and 5% citric acid was less lethal to metacercariae than 1% HCl in pepsin solution. Pepsin solution containing 5% citric acid had digestive capacity superior to pepsin solution containing 1% HCl after 3h incubation with released protein concentrations of 12.0 ng/ml for 5% citric acid and 9.6 ng/ml for 1% HCl. Accordingly, the present study suggests that the addition of 5% citric acid to pepsin solution is a good alternative to 1% HCl in infection studies because citric acid is a stable at room temperature and has a good safety profile. In addition, we suggest that the use of citric acid enables the preparation of commercial digestive solutions for the detection of microorganisms in fish and other vertebrate muscle tissue.

  5. Electrocatalytic and photocatalytic hydrogen production from acidic and neutral-pH aqueous solutions using iron phosphide nanoparticles.

    PubMed

    Callejas, Juan F; McEnaney, Joshua M; Read, Carlos G; Crompton, J Chance; Biacchi, Adam J; Popczun, Eric J; Gordon, Thomas R; Lewis, Nathan S; Schaak, Raymond E

    2014-11-25

    Nanostructured transition-metal phosphides have recently emerged as Earth-abundant alternatives to platinum for catalyzing the hydrogen-evolution reaction (HER), which is central to several clean energy technologies because it produces molecular hydrogen through the electrochemical reduction of water. Iron-based catalysts are very attractive targets because iron is the most abundant and least expensive transition metal. We report herein that iron phosphide (FeP), synthesized as nanoparticles having a uniform, hollow morphology, exhibits among the highest HER activities reported to date in both acidic and neutral-pH aqueous solutions. As an electrocatalyst operating at a current density of -10 mA cm(-2), FeP nanoparticles deposited at a mass loading of ∼1 mg cm(-2) on Ti substrates exhibited overpotentials of -50 mV in 0.50 M H2SO4 and -102 mV in 1.0 M phosphate buffered saline. The FeP nanoparticles supported sustained hydrogen production with essentially quantitative faradaic yields for extended time periods under galvanostatic control. Under UV illumination in both acidic and neutral-pH solutions, FeP nanoparticles deposited on TiO2 produced H2 at rates and amounts that begin to approach those of Pt/TiO2. FeP therefore is a highly Earth-abundant material for efficiently facilitating the HER both electrocatalytically and photocatalytically.

  6. Properties of Pb(0.92)La(0.08)Zr(0.52)Ti(0.48)O(3) thin films grown on SrRuO(3) buffered nickel and silicon substrates by chemical solution deposition

    SciTech Connect

    Narayanan, M.; Ma, B.; Tong, S.; Koritala, R.; Balachandran, U.

    2012-01-01

    Ferroelectric film-on-foil capacitors are suitable to replace discrete passive components in the quest to develop electronic devices that show superior performance and are smaller in size. The film-on-foil approach is the most practical method to fabricate such components. Films of Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} (PLZT) were deposited on SrRuO{sub 3} (SRO) buffer films over nickel and silicon substrates. High-quality polycrystalline SRO thin-film electrodes were first deposited by chemical solution deposition. A phase pure, dense, uniform microstructure with grain size <100 nm was obtained in films crystallized at 700 C. The room-temperature resistivity of the SRO films crystallized at 700 C was {approx}800-900 {mu}{Omega}-cm. The dielectric properties of sol-gel derived PLZT capacitors on SRO-buffered nickel were evaluated as a function of temperature, bias field, and frequency, and the results were compared to those of the same films on silicon substrates. The comparison demonstrated the integrity of the buffer layer and its compatibility with nickel substrates. Device-quality dielectric properties were measured on PLZT films deposited on SRO-buffered nickel foils and found to be superior to those for PLZT on SRO-buffered silicon and expensive platinized silicon. These results suggest that SRO films can act as an effective barrier layer on nickel substrates suitable for embedded capacitor applications.

  7. Ultrasonic degradation of oxalic acid in aqueous solutions.

    PubMed

    Dükkanci, M; Gündüz, G

    2006-09-01

    This paper describes the ultrasonic degradation of oxalic acid. The effects of ultrasonic power, H(2)O(2), NaCl, external gases on the degradation of oxalic acid were investigated. Reactor flask containing oxalic acid was immersed in the ultrasonic bath with water as the coupling fluid. Representative samples withdrawn were analysed by volumetric titration. Degradation degree of oxalic acid increased with increasing ultrasonic power. It was observed that H(2)O(2) has negative contribution on the degradation of oxalic acid and there was an optimum concentration of NaCl for enhancing the degradation degree of oxalic acid. Although bubbling nitrogen gave higher degradation than that for bubbling air, both gases (for 20 min before sonication and during sonication together) could not help to enhance the degradation of oxalic acid when compared with the degradation without gas passage. PMID:16352455

  8. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  9. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  10. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  11. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  12. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  13. Dietary Supplementation of Benzoic Acid and Essential Oil Compounds Affects Buffering Capacity of the Feeds, Performance of Turkey Poults and Their Antioxidant Status, pH in the Digestive Tract, Intestinal Microbiota and Morphology.

    PubMed

    Giannenas, I; Papaneophytou, C P; Tsalie, E; Pappas, I; Triantafillou, E; Tontis, D; Kontopidis, G A

    2014-02-01

    Three trials were conducted to evaluate the effect of supplementation of a basal diet with benzoic acid or thymol or a mixture of essential oil blends (MEO) or a combination of benzoic acid with MEO (BMEO) on growth performance of turkey poults. Control groups were fed a basal diet. In trial 1, benzoic acid was supplied at levels of 300 and 1,000 mg/kg. In trial 2, thymol or the MEO were supplied at levels of 30 mg/kg. In trial 3, the combination of benzoic acid with MEO was evaluated. Benzoic acid, MEO and BMEO improved performance, increased lactic acid bacteria populations and decreased coliform bacteria in the caeca. Thymol, MEO and BMEO improved antioxidant status of turkeys. Benzoic acid and BMEO reduced the buffering capacity compared to control feed and the pH values of the caecal content. Benzoic acid and EOs may be suggested as an effective alternative to AGP in turkeys. PMID:25049947

  14. Dietary Supplementation of Benzoic Acid and Essential Oil Compounds Affects Buffering Capacity of the Feeds, Performance of Turkey Poults and Their Antioxidant Status, pH in the Digestive Tract, Intestinal Microbiota and Morphology

    PubMed Central

    Giannenas, I.; Papaneophytou, C. P.; Tsalie, E.; Pappas, I.; Triantafillou, E.; Tontis, D.; Kontopidis, G. A.

    2014-01-01

    Three trials were conducted to evaluate the effect of supplementation of a basal diet with benzoic acid or thymol or a mixture of essential oil blends (MEO) or a combination of benzoic acid with MEO (BMEO) on growth performance of turkey poults. Control groups were fed a basal diet. In trial 1, benzoic acid was supplied at levels of 300 and 1,000 mg/kg. In trial 2, thymol or the MEO were supplied at levels of 30 mg/kg. In trial 3, the combination of benzoic acid with MEO was evaluated. Benzoic acid, MEO and BMEO improved performance, increased lactic acid bacteria populations and decreased coliform bacteria in the caeca. Thymol, MEO and BMEO improved antioxidant status of turkeys. Benzoic acid and BMEO reduced the buffering capacity compared to control feed and the pH values of the caecal content. Benzoic acid and EOs may be suggested as an effective alternative to AGP in turkeys. PMID:25049947

  15. Chemical evaluation of soil-solution in acid forest soils

    USGS Publications Warehouse

    Lawrence, G.B.; David, M.B.

    1996-01-01

    Soil-solution chemistry is commonly studied in forests through the use of soil lysimeters.This approach is impractical for regional survey studies, however, because lysimeter installation and operation is expensive and time consuming. To address these problems, a new technique was developed to compare soil-solution chemistry among red spruce stands in New York, Vermont, New Hampshire, Maine. Soil solutions were expelled by positive air pressure from soil that had been placed in a sealed cylinder. Before the air pressure was applied, a solution chemically similar to throughfall was added to the soil to bring it to approximate field capacity. After the solution sample was expelled, the soil was removed from the cylinder and chemically analyzed. The method was tested with homogenized Oa and Bs horizon soils collected from a red spruce stand in the Adirondack Mountains of New York, a red spruce stand in east-central Vermont, and a mixed hardwood stand in the Catskill Mountains of New York. Reproducibility, effects of varying the reaction time between adding throughfall and expelling soil solution (5-65 minutes) and effects of varying the chemical composition of added throughfall, were evaluated. In general, results showed that (i) the method was reproducible (coefficients of variation were generally < 15%), (ii) variations in the length of reaction-time did not affect expelled solution concentrations, and (iii) adding and expelling solution did not cause detectable changes in soil exchange chemistry. Concentrations of expelled solutions varied with the concentrations of added throughfall; the lower the CEC, the more sensitive expelled solution concentrations were to the chemical concentrations of added throughfall. Addition of a tracer (NaBr) showed that the expelled solution was a mixture of added solution and solution that preexisted in the soil. Comparisons of expelled solution concentrations with concentrations of soil solutions collected by zero-tension and

  16. Online concentration by field-amplified sample injection in acidic buffer for analysis of fangchinoline and tetrandrine in herbal medicine by flow injection-micellar electrokinetic capillary chromatography.

    PubMed

    Liu, Lihong; Chen, Xingguo; Hu, Zhide

    2005-12-01

    A novel, rapid, and continuous online concentration approach based on field-amplified sample injection for the analysis of fangchinoline and tetrandrine was developed in this paper by combination of flow injection-MEKC. The BGE used was a solution composed of 75 mM H3PO4-triethylamine-2.5% v/v polyoxyethylene sorbitan monolaurate-20% v/v methanol buffer (pH* 5.0). The analytes prepared in 50% v/v aqueous ethanol were used as the test analytes. Sample was injected electrokinetically between plugs of water. When the cations reached the boundary between the water plug and BGE, they slowed down and became concentrated. Thereafter, MEKC was initiated for the separation. This results in 6.8-8.9-fold improvement in concentration sensitivity relative to conventional CE methods. The separation could be achieved within 10 min and sample throughput rate can reach up to 50/h. The repeatability (defined as RSD) was 4.8, 4.4% with peak height evaluation and 3.6, 0.94% with peak area evaluation for TET and FAN, respectively. PMID:16259014

  17. Corrosion Behavior of Alloy 22 in Chloride Solutions Containing Organic Acids

    SciTech Connect

    Carranza, R M; Giordano, C M; Rodr?guez, M A; Rebak, R B

    2005-11-04

    Alloy 22 (N06022) is a nickel based alloy containing alloying elements such as chromium, molybdenum and tungsten. It is highly corrosion resistant both under reducing and under oxidizing conditions. Electrochemical studies such as electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. Tests were also carried out in NaCl solutions containing oxalic acid or acetic acid. It is shown that the corrosion rate of Alloy 22 was higher in a solution containing oxalic acid than in a solution of the same pH acidified with HCl. Acetic acid was not corrosive to Alloy 22. The corrosivity of oxalic acid was attributed to its capacity to form stable complex species with metallic cations from Alloy 22.

  18. The ototoxic effect of boric acid solutions applied into the middle ear of guinea pigs.

    PubMed

    Oztürkcan, Sedat; Dündar, Riza; Katilmis, Hüseyin; Ilknur, Ali Ekber; Aktaş, Sinem; Haciömeroğlu, Senem

    2009-05-01

    This study analyzed the ototoxic effects of boric acid solutions. Boric acid solutions have been used as otologic preparations for many years. Boric acid is commonly found in solutions prepared with alcohol or distilled water but can also be found in a powder form. These preparations are used for both their antiseptic and acidic qualities in external and middle ear infections. We investigated the ototoxic effect of boric acid solutions on guinea pigs. We are unaware of any similar, previously published study of this subject in English. The study was conducted on 28 young albino guinea pigs. Prior to application of the boric acid solution under general anesthesia, an Auditory Brainstem Response (ABRs) test was applied to the right ear of the guinea pigs. Following the test, a perforation was created on the tympanic membrane of the right ear of each guinea pig and small gelfoam pieces were inserted into the perforated area. Test solutions were administered to the middle ear for 10 days by means of a transcanal route. Fifteen days after inserting the gelfoams in all of the guinea pigs, we anasthesized the guinea pigs and removed the gelfoams from the perforated region of the ear and then performed an ABRs on each guinea pig. The ABRs were within the normal range before the applications. After the application, no significant changes were detected in the ABRs thresholds in neither the saline group nor the group administered boric acid and distilled water solution; however, significant changes were detected in the ABRs thresholds of the Gentamicine and boric acid and alcohol solution groups. We believe that a 4% boric acid solution prepared with distilled water can be a more reliable preparation than a 4% boric acid solution prepared with alcohol.

  19. The standard enthalpies of formation of crystalline N-(carboxymethyl)aspartic acid and its aqueous solutions

    NASA Astrophysics Data System (ADS)

    Lytkin, A. I.; Chernyavskaya, N. V.; Volkov, A. V.; Nikol'Skii, V. M.

    2007-07-01

    The energy of combustion of N-(carboxymethyl)aspartic acid (CMAA) was determined by bomb calorimetry in oxygen. The standard enthalpies of combustion and formation of crystalline N-(carboxymethyl)aspartic acid were calculated. The heat effects of solution of crystalline CMAA in water and a solution of sodium hydroxide were measured at 298.15 K by direct calorimetry. The standard enthalpies of formation of CMAA and its dissociation products in aqueous solution were determined.

  20. Solution properties and taste behavior of lactose monohydrate in aqueous ascorbic acid solutions at different temperatures: Volumetric and rheological approach.

    PubMed

    Sarkar, Abhijit; Sinha, Biswajit

    2016-11-15

    The densities and viscosities of lactose monohydrate in aqueous ascorbic acid solutions with several molal concentrations m=(0.00-0.08)molkg(-1) of ascorbic acid were determined at T=(298.15-318.15)K and pressure p=101kPa. Using experimental data apparent molar volume (ϕV), standard partial molar volume (ϕV(0)), the slope (SV(∗)), apparent specific volumes (ϕVsp), standard isobaric partial molar expansibility (ϕE(0)) and its temperature dependence [Formula: see text] the viscosity B-coefficient and solvation number (Sn) were determined. Viscosity B-coefficients were further employed to obtain the free energies of activation of viscous flow per mole of the solvents (Δμ1(0≠)) and of the solute (Δμ2(0≠)). Effects of molality, solute structure and temperature and taste behavior were analyzed in terms of solute-solute and solute-solvent interactions; results revealed that the solutions are characterized predominantly by solute-solvent interactions and lactose monohydrate behaves as a long-range structure maker. PMID:27283672

  1. Biosorption of acidic textile dyestuffs from aqueous solution by Paecilomyces sp. isolated from acidic mine drainage.

    PubMed

    Çabuk, Ahmet; Aytar, Pınar; Gedikli, Serap; Özel, Yasemin Kevser; Kocabıyık, Erçin

    2013-07-01

    Removal of textile dyestuffs from aqueous solution by biosorption onto a dead fungal biomass isolated from acidic mine drainage in the Çanakkale Region of Turkey was investigated. The fungus was found to be a promising biosorbent and identified as Paecilomyces sp. The optimal conditions for bioremediation were as follows: pH, 2.0; initial dyestuff concentration, 50 mg l(-1) for Reactive Yellow 85 and Reactive Orange 12, and 75 mg l(-1) for Reactive Black 8; biomass dosage, 2 g l(-1) for Reactive Yellow 85, 3 g l(-1) for Reactive Orange 12, 4 g l(-1) for Reactive Black 8; temperature, 25 °C; and agitation rate, 100 rpm. Zeta potential measurements indicated an electrostatic interaction between the binding sites and dye anions. Fourier transform infrared spectroscopy showed that amine, hydroxyl, carbonyl, and amide bonds were involved in the dyestuff biosorption. A toxicity investigation was also carried out before and after the biosorption process. These results showed that the toxicities for the reactive dyestuffs in aqueous solutions after biosorption studies decreased. The Freundlich and Langmuir adsorption models were used for the mathematical description of the biosorption equilibrium, and isotherm constants were evaluated for each dyestuff. Equilibrium data of biosorption of RY85 and RO12 dyestuffs fitted well to both models at the studied concentration and temperature.

  2. Buffer Standards for the Physiological pH of the Zwitterionic Compound, DIPSO from 5 to 55°C

    PubMed Central

    Roy, Lakshmi N.; Roy, Rabindra N.; LeNoue, Sean R.; Denton, Cole E.; Fuge, Michael S.; Dunseth, Craig D.; Roy, Chandra N.; Hayden, Shawn M.; Wollen, Joshua T.; Sreepada, Kripa

    2009-01-01

    The values of the second dissociation constant, pK2, and related thermodynamic quantities of 3-[N,N-bis (2-hydroxyethyl)amino]-2-hydroxypropanesulfonic acid (DIPSO) have already been reported over the temperature range 5 to 55°C including 37°C. This paper reports the pH values of four NaCl-free buffer solutions and four buffer composition containing NaCl salt at I = 0.16 mol·kg−1. Conventional paH values are reported for all eight buffer solutions. The operational pH values have been calculated for four buffer solutions recommended as pH standards, at 25 and 37°C after correcting the liquid junction potentials with the flowing junction cell. PMID:20160870

  3. Buffer Standards for the Physiological pH of the Zwitterionic Compound, DIPSO from 5 to 55 degrees C.

    PubMed

    Roy, Lakshmi N; Roy, Rabindra N; Lenoue, Sean R; Denton, Cole E; Fuge, Michael S; Dunseth, Craig D; Roy, Chandra N; Hayden, Shawn M; Wollen, Joshua T; Sreepada, Kripa

    2009-04-01

    The values of the second dissociation constant, pK(2), and related thermodynamic quantities of 3-[N,N-bis (2-hydroxyethyl)amino]-2-hydroxypropanesulfonic acid (DIPSO) have already been reported over the temperature range 5 to 55 degrees C including 37 degrees C. This paper reports the pH values of four NaCl-free buffer solutions and four buffer composition containing NaCl salt at I = 0.16 mol.kg(-1). Conventional pa(H) values are reported for all eight buffer solutions. The operational pH values have been calculated for four buffer solutions recommended as pH standards, at 25 and 37 degrees C after correcting the liquid junction potentials with the flowing junction cell.

  4. Removal of radium from acidic solutions containing same by adsorption on coal fly ash

    DOEpatents

    Scheitlin, Frank M.

    1984-01-01

    The invention is a process for the removal of radium from acidic aqueous solutions. In one aspect, the invention is a process for removing radium from an inorganic-acid solution. The process comprises contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple, comparatively inexpensive, and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities throughout the United States. The invention is applicable, for example, to the recovery of .sup.226 Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings.

  5. Process for the removal of radium from acidic solutions containing same

    DOEpatents

    Scheitlin, F.M.

    The invention is a process for the removal of radium from acidic aqueous solutions. In one aspect, the invention is a process for removing radium from an inorganic-acid solution. The process comprises contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple, comparatively inexpensive, and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities throughout the United States. The invention is applicable, for example, to the recovery of /sup 226/Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings.

  6. Simultaneous analysis of several antiretroviral nucleosides in rat-plasma by high-performance liquid chromatography with UV using acetic acid/hydroxylamine buffer Test of this new volatile medium-pH for HPLC-ESI-MS/MS.

    PubMed

    Bezy, Vincent; Morin, Philippe; Couerbe, Philippe; Leleu, Ghislaine; Agrofoglio, Luigi

    2005-07-25

    Zalcitabine (ddC), lamivudine (3TC), didanosine (ddI), stavudine (d4T), carbovir (CBV), zidovudine (AZT), tenofovir (PMPA) and its administrated form (tenofovir diisoproxyl fumarate, TDF), are nucleosides currently approved in HIV therapy. To facilitate pharmacokinetics studies, a specific reversed-phase high-performance liquid chromatography (HPLC) method was developed for their analysis in rat plasma. The method involved a quantitative recovery of these drugs from rat plasma by solid-phase extraction on Oasis HLB Waters cartridges followed by optimised HPLC separation on an Atlantis dC18 column with acetic acid-hydroxylamine buffer (ionic strength 5mM, pH 7)-acetonitrile elution gradient. Quantitation was performed by HPLC/UV at 260 nm. Linear calibration curves were obtained within a 30-10,000 ng/mL plasma concentration range. Correlation coefficients (r2) greater than 0.992 were obtained by least-squares regression and limits of quantification were in 30-90 ng/mL concentration range. Quantitative parameters (accuracy, intra-day repeatability and inter-day reproducibility) yielded satisfactory results. Finally, a new buffer, obtained with acetic acid and hydroxylamine, has been tested in HPLC/ESI-MS/MS and appears to be an efficient volatile buffer in the medium 5-7 pH range. Indeed, at pH 7 and low ionic strength (5 mM), its buffer capacity is one hundred times higher to that obtained for the usual acetic acid/ammonia buffer.

  7. Discoloration of titanium alloy in acidic saline solutions with peroxide.

    PubMed

    Takemoto, Shinji; Hattori, Masayuki; Yoshinari, Masao; Kawada, Eiji; Oda, Yutaka

    2013-01-01

    The objective of this study was to compare corrosion behavior in several titanium alloys with immersion in acidulated saline solutions containing hydrogen peroxide. Seven types of titanium alloy were immersed in saline solutions with varying levels of pH and hydrogen peroxide content, and resulting differences in color and release of metallic elements determined in each alloy. Some alloys were characterized using Auger electron spectroscopy. Ti-55Ni alloy showed a high level of dissolution and difference in color. With immersion in solution containing hydrogen peroxide at pH 4, the other alloys showed a marked difference in color but a low level of dissolution. The formation of a thick oxide film was observed in commercially pure titanium showing discoloration. The results suggest that discoloration in titanium alloys immersed in hydrogen peroxide-containing acidulated solutions is caused by an increase in the thickness of this oxide film, whereas discoloration of Ti-55Ni is caused by corrosion. PMID:23370866

  8. Separation of ions in acidic solution by capillary electrophoresis

    SciTech Connect

    Thornton, M.

    1997-10-08

    Capillary electrophoresis (CE) is an effective method for separating ionic species according to differences in their electrophoretic mobilities. CE separations of amino acids by direct detection are difficult due to their similar electrophoretic mobilities and low absorbances. However, native amino acids can be separated by CE as cations at a low pH by adding an alkanesulfonic acid to the electrolyte carrier which imparts selectivity to the system. Derivatization is unnecessary when direct UV detection is used at 185 nm. Simultaneous speciation of metal cations such as vanadium (IV) and vanadium (V) can easily be performed without complexation prior to analysis. An indirect UV detection scheme for acidic conditions was also developed using guanidine as the background carrier electrolyte (BCE) for the indirect detection of metal cations. Three chapters have been removed for separate processing. This report contains introductory material, references, and general conclusions. 80 refs.

  9. Fabrication of organic FETs based on printing techniques and the improvement of FET properties by the insertion of solution-processable buffer layers

    NASA Astrophysics Data System (ADS)

    Itoh, Eiji; Kanamori, Akira

    2016-04-01

    In this study, we developed multilayer deposition and patterning processes that can be used to fabricate all-printed, organic field-effect transistors (OFETs) on the basis of vacuum-free, solution-processable soft-lithography techniques. We have used regioregular poly(3-hexylthiophene) (P3HT) as a soluble p-type polymer semiconductor and (6,6)-phenyl C61 butyric acid methyl ester (PCBM) as a soluble n-type semiconductor, and cross-linked poly(vinyl phenol) (CL-PVP) as a low-temperature (<150 °C)-curable soluble polymer gate insulator. We have compared the electrical properties of OFETs with multiwalled carbon nanotubes (MWCNTs), silver nanoparticles (NPs), and their composites (or multilayers) as printed source-drain (S-D) electrodes in order to fabricate vacuum-free, all-printed OFETs. The P3HT-OFETs with MWCNT S-D electrodes exhibited higher hole mobility and on/off ratios than the devices with Ag NP S-D electrodes owing to better contact at the MWCNT/P3HT interface. On the other hand, Ag/molybdenum oxide (MoO3) S-D electrodes considerably enhanced the hole injection and caused the reduction in the on/off ratio and the difficulty in turning off the devices. The PCBM-OFETs with MWCNT S-D electrodes also exhibited higher electron mobility that is almost comparable to that of P3HT-OFETs and lower threshold voltage, which was considered to be due to the enhanced electron injection at the electrode interface.

  10. Dynamic dielectric properties of some carboxylic acid esters in benzene solution

    NASA Astrophysics Data System (ADS)

    Ghoneim, Ahmed M.; Stockhause, Martina; Becker, U.; Biedenkap, R.; Elsebrock, R.

    1997-06-01

    The dielectric absorption spectrum between some MHz and 36 GHz has been measured at 20 degrees C for S(-)-lactic acid methylester, succinic acid dimethylester, L(-)- malic acid dimethylester and L(+)-tartaric acid diethylester, over the whole concentration range of benzene solutions of these substances. The loss function can be described by up to four Debye type spectral components. The relaxation parameters are reported and discussed in particular with respect to association effects.

  11. Near infrared photochemistry of pyruvic acid in aqueous solution.

    PubMed

    Larsen, Molly C; Vaida, Veronica

    2012-06-21

    Recent experimental and theoretical results have suggested that organic acids such as pyruvic acid, can be photolyzed in the ground electronic state by the excitation of the OH stretch vibrational overtone. These overtones absorb in the near-infrared and visible regions of the spectrum where the solar photons are plentiful and could provide a reaction pathway for the organic acids and alcohols that are abundant in the earth's atmosphere. In this paper the overtone initiated photochemistry of aqueous pyruvic acid is investigated by monitoring the evolution of carbon dioxide. In these experiments CO(2) is being produced by excitation in the near-infrared, between 850 nm and ∼1150 nm (11,765-8696 cm(-1)), where the second OH vibrational overtone (Δν = 3) of pyruvic acid is expected to absorb. These findings show not only that the overtone initiated photochemical decarboxylation reaction occurs but also that in the aqueous phase it occurs at a lower energy than was predicted for the overtone initiated reaction of pyruvic acid in the gas phase (13,380 cm(-1)). A quantum yield of (3.5 ± 1.0) × 10(-4) is estimated, suggesting that although this process does occur, it does so with a very low efficiency.

  12. New insights into structural alteration of enamel apatite induced by citric acid and sodium fluoride solutions.

    PubMed

    Wang, Xiaojie; Klocke, Arndt; Mihailova, Boriana; Tosheva, Lubomira; Bismayer, Ulrich

    2008-07-24

    Attenuated total reflectance infrared spectroscopy and complementary scanning electron microscopy were applied to analyze the surface structure of enamel apatite exposed to citric acid and to investigate the protective potential of fluorine-containing reagents against citric acid-induced erosion. Enamel and, for comparison, geological hydroxylapatite samples were treated with aqueous solutions of citric acid and sodium fluoride of different concentrations, ranging from 0.01 to 0.5 mol/L for citric acid solutions and from 0.5 to 2.0% for fluoride solutions. The two solutions were applied either simultaneously or consecutively. The citric acid-induced structural modification of apatite increases with the increase in the citric acid concentration and the number of treatments. The application of sodium fluoride alone does not suppress the atomic level changes in apatite exposed to acidic agents. The addition of sodium fluoride to citric acid solutions leads to formation of surface CaF2 and considerably reduces the changes in the apatite P-O-Ca framework. However, the CaF2 globules deposited on the enamel surface seem to be insufficient to prevent the alteration of the apatite structure upon further exposure to acidic agents. No evidence for fluorine-induced recovery of the apatite structure was found.

  13. PROCESS OF SECURING PLUTONIUM IN NITRIC ACID SOLUTIONS IN ITS TRIVALENT OXIDATION STATE

    DOEpatents

    Thomas, J.R.

    1958-08-26

    >Various processes for the recovery of plutonium require that the plutonium be obtalned and maintained in the reduced or trivalent state in solution. Ferrous ions are commonly used as the reducing agent for this purpose, but it is difficult to maintain the plutonium in a reduced state in nitric acid solutions due to the oxidizing effects of the acid. It has been found that the addition of a stabilizing or holding reductant to such solution prevents reoxidation of the plutonium. Sulfamate ions have been found to be ideally suitable as such a stabilizer even in the presence of nitric acid.

  14. Reprocessing system with nuclide separation based on chromatography in hydrochloric acid solution

    SciTech Connect

    Suzuki, Tatsuya; Tachibana, Yu; Koyama, Shi-ichi

    2013-07-01

    We have proposed the reprocessing system with nuclide separation processes based on the chromatographic technique in the hydrochloric acid solution system. Our proposed system consists of the dissolution process, the reprocessing process, the minor actinide separation process, and nuclide separation processes. In the reprocessing and separation processes, the pyridine resin is used as a main separation media. It was confirmed that the dissolution in the hydrochloric acid solution is easily achieved by the plasma voloxidation and by the addition of oxygen peroxide into the hydrochloric acid solution.

  15. Preparation of Buffers. An Experiment for Quantitative Analysis Laboratory

    NASA Astrophysics Data System (ADS)

    Buckley, P. T.

    2001-10-01

    In our experience, students who have a solid grounding in the theoretical aspects of buffers, buffer preparation, and buffering capacity are often at a loss when required to actually prepare a buffer in a research setting. However, there are very few published laboratory experiments pertaining to buffers. This laboratory experiment for the undergraduate quantitative analysis lab gives students hands-on experience in the preparation of buffers. By preparing a buffer to a randomly chosen pH value and comparing the theoretical pH to the actual pH, students apply their theoretical understanding of the Henderson-Hasselbalch equation, activity coefficients, and the effect of adding acid or base to a buffer. This experiment gives students experience in buffer preparation for research situations and helps them in advanced courses such as biochemistry where a fundamental knowledge of buffer systems is essential.

  16. Solute-solvent interactions in micellar electrokinetic chromatography. 6. Optimization of the selectivity of lithium dodecyl sulfate-lithium perfluorooctanesulfonate mixed micellar buffers.

    PubMed

    Fuguet, Elisabet; Ràfols, Clara; Torres-Lapasió, José Ramón; García-Alvarez-Coque, María Celia; Bosch, Elisabeth; Rosés, Martí

    2002-09-01

    The optimization of the composition of mixed surfactants used as micellar electrokinetic chromatography (MEKC) pseudostationary phases is proposed as an effective method for the separation of complex mixtures of analytes. The solvation parameter model is used to select two surfactants (lithium dodecyl sulfate, LDS, and lithium perfluorooctanesulfonate, LPFOS) with contrasting solvation properties. Combination of these two surfactants allows variations of the solvation properties of MEKC pseudostationary phase along a wide range. Thus, the convenient variation of the proportion of both surfactants allows an effective control of the selectivity in such systems. An algorithm that predicts the overall resolution of a given mixture of compounds is described and applied to optimize the composition of the mixed surfactant for the separation of the mixture. The algorithm is based on the calculation of peak purities on simulated chromatograms as a function of the composition of the mixed LDS/LPFOS micellar buffer from data at several micellar buffer compositions. Successful separations were achieved for mixtures containing up to 20 compounds, in less than 12 min.

  17. Mechanistic studies of nitrations and oxidations in solutions of dinitrogen pentaoxide in nitric acid

    SciTech Connect

    Willmer, R.F.

    1992-01-01

    Mechanisms of nitrations in solutions of dinitrogen pentaoxide in nitric acid of 1,2,4-trichloro-5-nitrobenzene and 1,2-dichloro-4-nitrobenzene have been proposed. The kinetics and products of the nitration, in the title medium, of substantially deactivated benzoic acids and benzaldehydes have been investigated. Kinetics of nitration of some substituted benzoic acids in nitric acid solutions containing dinitrogen pentaoxide or nitronium trifluoro-methanesulphonate (nitronium triflate) have been compared. Rate coefficients for reactions in dinitrogen pentaoxide solutions were generally similar to those from nitronium triflate solutions of the same estimated nitronium ion concentration. Yields of aromatic products of nitration of some benzoic acid derivatives in the nitric acid solutions have been determined. Nitrodecarboxylation of 4-fluorobenzoic acid occurs as a result of nitronium ion attach at C(1). The competition between oxidation to the corresponding benzoic acid and nitration in the aromatic ring of some substituted benzaldehydes has been probed by kinetic and product studies. 4-Carboxybenzaldehyde is nitrated but more deactivated substrates are predominantly oxidized. Rapid reversible gem-dinitrate formation occurs in concentrated dinitrogen pentaoxide solutions. The equilibrium extent of formation of [alpha]-deuterio-(4-nitropheny)-dinitratomethane from [alpha]-deuterio-4-nitrobenzaldehyde is reported. 4-nitrobenzaldehyde and the gem-dinitrate are oxidized in processes in which [alpha]-hydrogen loss is at least partially rate determining. The relative rates of oxidation in nitronium triflate solutions suggest that the [alpha]-hydrogen is removed as a hydride ion in that medium. There is evidence for the intrusion of a radical mechanism of nitration in concentrated solutions of dinitrogen pentaoxide. (4-Nitrophenyl)dinitratomethane was produced on the addition of 4-nitrobenzaldehyde to a solution of dinitrogen pentaoxide in dichloromethane.

  18. Effect of acidic solutions on the surface degradation of a micro-hybrid composite resin.

    PubMed

    Münchow, Eliseu A; Ferreira, Ana Cláudia A; Machado, Raissa M M; Ramos, Tatiana S; Rodrigues-Junior, Sinval A; Zanchi, Cesar H

    2014-01-01

    Composite resins may undergo wear by the action of chemical substances (e.g., saliva, alcohol, bacterial acids) of the oral environment, which may affect the material's structure and surface properties. This study evaluated the effect of acidic substances on the surface properties of a micro-hybrid composite resin (Filtek Z-250). Eighty specimens were prepared, and baseline hardness and surface roughness (KMN0 and Ra0, respectively) were measured. The specimens were subjected to sorption (SO) and solubility (SL) tests according to ISO 4049:2009, but using different storage solutions: deionized water; 75/25 vol% ethanol/water solution; lactic acid; propionic acid; and acetic acid. The acids were used in two concentrations: PA and 0.02 N. pH was measured for all solutions and final hardness (KMN1) and surface roughness (Ra1) were measured. Data were analyzed with paired t-tests and one-way ANOVA and Tukey's test (a=5%). All solutions decreased hardness and increased the Ra values, except for the specimens stored in water and 0.02 N lactic acid, which maintained the hardness. All solutions produced similar SO and SL phenomena, except for the 0.02 N lactic acid, which caused lower solubility than the other solutions. Ethanol showed the highest pH (6.6) and the 0.02 N lactic acid the lowest one (2.5). The solutions affected negatively the surface properties of the composite resin; in addition, an acidic pH did not seem to be a significant factor that intensifies the surface degradation phenomena. PMID:25250496

  19. Temperature dependence of hydrogen-bond dynamics in acetic acid-water solutions.

    PubMed

    D'Amico, Francesco; Bencivenga, Filippo; Gessini, Alessandro; Masciovecchio, Claudio

    2010-08-19

    An inelastic UV scattering experiment has been carried out on acetic acid-water solutions as a function of temperature and concentration. The analysis of experimental data indicates the presence of a crossover temperature (T(c) approximately 325 +/- 10 K). Above T(c), the energy of hydrogen bonds responsible for water-acetic acid and acetic acid-acetic acid interactions is strongly reduced. This leads to a reduction in the average number of water molecule interacting with acetic acid, as well as to a lower number of acetic acid clusters. The latter behavior can be mainly ascribed to a temperature change in the activation energy of carboxylic groups of acetic acid. These results may be also relevant to better understand the folding mechanism in protein-water solutions. PMID:20701390

  20. The Solubility of Xenon in Simple Organic Solvents and in Aqueous Amino Acid Solutions.

    NASA Astrophysics Data System (ADS)

    Himm, Jeffrey Frank

    We have measured the Ostwald solubility (L) of ('133)Xe in a variety of liquids, including normal alkanes, normal alkanols, and aqueous solutions of amino acids, NaCl, and sucrose. For the alkanes and alkanols, measurements were made in the temperature range from 10-50(DEGREES)C. Values of L were found to decrease with increasing temperature, and also with increasing chain length, for both series of solvents. Thermodynamic properties of solution (enthalpy and entropy of solution) are calculated using both mole fraction and number density scales. Results are interpreted using Uhlig's model of the solvation process. Measurements of L in aqueous amino acid solutions were made at 25(DEGREES)C. Concentrations of amino acids in solution varied from near saturation for each of the amino acids studied to pure water. In all solutions, except those with NaCl, L decreases linearly with increasing solution molarity. Hydration numbers (H), the mean number of water molecules associated with each solute molecule, were determined for each amino acid, for NaCl, and for sucrose. Values of H obtained ranged from near zero (arginine, H = 0.2 (+OR-) 0.5) to about 16 (NaCl, H = 16.25 (+OR-) 0.3).

  1. Multiple-acid equilibria in adsorption of carboxylic acids from dilute aqueous solution

    SciTech Connect

    Husson, S.M.; King, C.J.

    1999-02-01

    Equilibria were measured for adsorption of carboxylic acids from aqueous, binary-acid mixtures of lactic and succinic acids and acetic and formic acids onto basic polymeric sorbents. The experimentally determined adsorption isotherms compared well with model predictions, confirming that simple extensions from adsorption of individual acids apply. Fixed-bed studies were carried out that establish the efficacy of chromatographic fractionation of lactic and succinic acids using basic polymeric sorbents. Finally, sequential thermal and solvent regeneration of lactic and acetic acid-laden sorbents was investigated as a method to fractionate among coadsorbed volatile and nonvolatile acids. Essentially complete removal of the acetic acid from the acid-laden sorbent was achieved by vaporization under the conditions used; a small amount of loss of lactic acid (about 11%) was observed.

  2. Extent and mechanism of solvation and partitioning of isomers of substituted benzoic acids: a thermodynamic study in the solid state and in solution.

    PubMed

    Perlovich, German L; Volkova, Tatyana V; Manin, Alex N; Bauer-Brandl, Annette

    2008-09-01

    Temperature dependency of saturated vapour pressure and thermochemical characteristics of fusion processes for 2-, 3- and 4-methoxybenzoic acids (anisic acids) were measured and thermodynamic functions of sublimation, fusion, and evaporation calculated. A new approach to split specific and nonspecific energetic terms in the crystal lattice was developed. For methoxybenzoic acid isomers as well as for a number of analogous molecules, a parameter describing molecular packing density by the ratio of free volume of the molecules in the crystal lattice and van der Waals molecular volume is defined. Its relationship to Gibbs energy of sublimation and to the respective melting points was analysed. Temperature dependencies of solubility in buffers with pH 2.0 and 7.4, n-octanol and n-hexane were measured. The thermodynamic functions of solubility, solvation and transfer processes were deduced. Concentration dependence of partition coefficients for the outlined isomers was measured. Specific and nonspecific solvation terms were distinguished using the transfer from the 'inert' n-hexane to the other solvents. Comparison analysis of specific and nonspecific interactions in the solid state and in solution was carried out. A diagram enabling analysis of the mechanism of the partitioning process was applied. It was found that position of substituents essentially affects the mechanism of partitioning in buffer pH 2.0, however, at pH 7.4, the mechanism is independent of the position of the substituent. PMID:18200548

  3. VIRTUAL FRAME BUFFER INTERFACE

    NASA Technical Reports Server (NTRS)

    Wolfe, T. L.

    1994-01-01

    Large image processing systems use multiple frame buffers with differing architectures and vendor supplied user interfaces. This variety of architectures and interfaces creates software development, maintenance, and portability problems for application programs. The Virtual Frame Buffer Interface program makes all frame buffers appear as a generic frame buffer with a specified set of characteristics, allowing programmers to write code which will run unmodified on all supported hardware. The Virtual Frame Buffer Interface converts generic commands to actual device commands. The virtual frame buffer consists of a definition of capabilities and FORTRAN subroutines that are called by application programs. The virtual frame buffer routines may be treated as subroutines, logical functions, or integer functions by the application program. Routines are included that allocate and manage hardware resources such as frame buffers, monitors, video switches, trackballs, tablets and joysticks; access image memory planes; and perform alphanumeric font or text generation. The subroutines for the various "real" frame buffers are in separate VAX/VMS shared libraries allowing modification, correction or enhancement of the virtual interface without affecting application programs. The Virtual Frame Buffer Interface program was developed in FORTRAN 77 for a DEC VAX 11/780 or a DEC VAX 11/750 under VMS 4.X. It supports ADAGE IK3000, DEANZA IP8500, Low Resolution RAMTEK 9460, and High Resolution RAMTEK 9460 Frame Buffers. It has a central memory requirement of approximately 150K. This program was developed in 1985.

  4. In vitro evaluation of the cytotoxic effects of acid solutions used as canal irrigants.

    PubMed

    Malheiros, C F; Marques, M M; Gavini, G

    2005-10-01

    Solutions of EDTA and citric acid have been used as canal irrigants. These substances must be compatible with apical periodontal tissue. The aim of this study was to evaluate comparatively the cytotoxicity of a 17% EDTA solution and that of three solutions with different concentrations of citric acid (10, 15, and 25%) on cultured fibroblasts. The solutions were diluted to 0.1% and 0.5% in culture medium and then applied to NIH 3T3 cells. After 0, 6, 12, and 24 h (short-term assay; viability) and 1, 3, 5, and 7 days (long-term assay; survival), the cells were counted. The data were compared by ANOVA. In the short-term experiments, all solutions presented a percentage of cell viability similar to that of control cells, except for the 17% EDTA solution diluted to 0.5%. After the long-term assay, all groups presented a continuous and progressive cell growth except for the 17% EDTA solution and for the 25% citric acid solution at a 0.5% dilution. The citric acid solution did not impair cell growth and viability, proving to be noncytotoxic in vitro.

  5. Standard addition method for free acid determination in solutions with hydrolyzable ions

    SciTech Connect

    Baumann, E.W.

    1981-01-01

    The free acid content of solutions containing hydrolyzable ions has been determined potentiometrically by a standard addition method. Two increments of acid are added to the sample in a 1M potassium thiocyanate solution. The sample concentration is calculated by solution of three simultaneous Nernst equations. The method has been demonstrated for solutions containing Al/sup 3 +/, Cr/sup 3 +/, Fe/sup 3 +/, Ni/sup 2 +/, Th/sup 4 +/, or UO/sub 2//sup 2 +/ with a metal-to-acid ratio of < 2.5. The method is suitable for determination of 10 ..mu..moles acid in 10 mL total volume. The accuracy is verifiable by reasonable agreement of the Nerst slopes found in the presence and absence of hydrolyzable ions. The relative standard deviation is < 2.5 percent.

  6. Thermodynamics of the complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Mudarisova, R. Kh.; Badykova, L. A.

    2016-03-01

    The thermodynamics of complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions is studied by means spectroscopy. The standard thermodynamic characteristics (Δ H°; Δ G°; Δ S°) of complexation are calculated.

  7. Investigation of the swelling behaviour of hydrogels in aqueous acid or alkaline solutions

    NASA Astrophysics Data System (ADS)

    Althans, Daniel; Enders, Sabine

    2014-09-01

    For development of tailor made drug delivery systems using poly(N-isopropylacrylamide) hydrogels, the influence of acids and bases added to the aqueous solution on the swelling behaviour as function of concentration, temperature and kind of acid or base were investigated experimentally. The selected acids are formic, acetic, propionic, lactic, succinic, α-ketoglutaric and citric acid. The applied bases are sodium and potassium hydroxide. The swelling behaviour was characterised by the degree of swelling and by the uptake of acids by the hydrogel in the swollen state. In the case of weak acids the properties of the swollen hydrogel as well as the phase transition temperature and phase transition acid concentration depends on the type of acids, whereas the properties of the shrunken state do not depend on the acid used. In the case of strong bases, the properties of the shrunken and swollen state depend on the ionic strength, but not on the base applied.

  8. Effects of peroxyacetic acid, acidified sodium chlorite or lactic acid solutions on the microflora of chilled beef carcasses.

    PubMed

    Gill, C O; Badoni, M

    2004-02-15

    The effects of solutions of 0.02% peroxyacetic acid, acidified 0.16% sodium chlorite, 2% lactic acid and 4% lactic acid on the natural flora of the distal surfaces of pieces of brisket, from chilled beef carcass quarters delivered from two slaughtering plants to a processing plant, were investigated. Peroxyacetic acid and acidified sodium chlorite solutions had little effect on the numbers of aerobes, coliforms or Escherichia coli on meat from one plant, and were less effective than 4% lactic acid for reducing the numbers of bacteria on meat from the other plant. With meat from both plants, treatment of meat with 4% lactic acid and holding for 5 or 60 min at 7+/-1 degrees C before sampling resulted in reductions of all three groups of bacteria by >/=1.5 log unit. Treatment with 2% lactic acid resulted in similar reductions when meat was sampled 5 min after the treatment, but reductions were about 1 log unit when meat was sampled 60 min after the treatment. Treatment of carcass quarters with 4% lactic acid resulted in reductions of bacterial numbers of >/=2 log units at distal surfaces, but solutions may be inconsistent when they are applied to chilled meat from different sources and to different types of meat surface, and that bacteria injured by application of an antimicrobial solution may recover during processing of meat at temperatures about 7 degrees C. However, 4% lactic acid may be generally useful as a decontaminant for chilled, raw meat. PMID:14967559

  9. Thermodynamic and Ultrasonic Properties of Ascorbic Acid in Aqueous Protic Ionic Liquid Solutions

    PubMed Central

    Singh, Vickramjeet; Sharma, Gyanendra; Gardas, Ramesh L.

    2015-01-01

    In this work, we report the thermodynamic and ultrasonic properties of ascorbic acid (vitamin C) in water and in presence of newly synthesized ammonium based protic ionic liquid (diethylethanolammonium propionate) as a function of concentration and temperature. Apparent molar volume and apparent molar isentropic compression, which characterize the solvation state of ascorbic acid (AA) in presence of protic ionic liquid (PIL) has been determined from precise density and speed of sound measurements at temperatures (293.15 to 328.15) K with 5 K interval. The strength of molecular interactions prevailing in ternary solutions has been discussed on the basis of infinite dilution partial molar volume and partial molar isentropic compression, corresponding volume of transfer and interaction coefficients. Result has been discussed in terms of solute-solute and solute-solvent interactions occurring between ascorbic acid and PIL in ternary solutions (AA + water + PIL). PMID:26009887

  10. Behaviors of acrylamide/itaconic acid hydrogels in uptake of uranyl ions from aqueous solutions

    SciTech Connect

    Karadag, E.; Saraydin, D.; Gueven, O.

    1995-12-01

    In this study, adsorptions of uranyl ions from two different aqueous uranyl solutions by acrylamide-itaconic acid hydrogels were investigated by a spectroscopic method. The hydrogels were prepared by irradiating with {gamma}-radiation. In the experiment of uranyl ions adsorption, Type II adsorption was found. One gram of acrylamide-itaconic acid hydrogels sorbed 178-219 mg uranyl ions from the solutions of uranyl acetate, 42-76 mg uranyl ions from the aqueous solutions of uranyl nitrate, while acrylamide hydrogel did not sorb any uranyl ion. For the hydrogel containing 40 mg of itaconic acid and irradiated to 3.73 kGy, swelling of the hydrogels was observed in water (1660%), in the aqueous solution of uranyl acetate (730%), and in the aqueous solution of uranyl nitrate (580%). Diffusions of water onto hydrogels were a non-Fickian type of diffusion, whereas diffusions of uranyl ions were a Fickian type of diffusion.

  11. Process for recovering uranium using an alkyl pyrophosphoric acid and alkaline stripping solution

    SciTech Connect

    Worthington, R.E.; Magdics, A.

    1987-03-24

    A process is described for stripping uranium for a pregnant organic extractant comprising an alkyl pyrophosphoric acid dissolved in a substantially water-immiscible organic diluent. The organic extractant contains tetravalent uranium and an alcohol or phenol modifier in a quantity sufficient to retain substantially all the unhydrolyzed alkyl pyrophosphoric acid in solution in the diluent during stripping. The process comprises adding an oxidizing agent to the organic extractant and thereby oxidizing the tetravalent uranium to the +6 state in the organic extractant, and contacting the organic extractant containing the uranium in the +6 state with a stripping solution comprising an aqueous solution of an alkali metal or ammonium carbonate or hydroxide thereby stripping uranium from the organic extractant into the stripping solution. The resulting barren organic extractant containing substantially all of the unhydrolyzed alkyl pyrophosphoric acid dissolved in the diluent is separated from the stripping solution containing the stripped uranium, the barren extractant being suitable for recycle.

  12. Process for recovering uranium using an alkyl pyrophosphoric acid and alkaline stripping solution

    SciTech Connect

    Worthington, R.E.; Magdics, A.

    1987-03-24

    A process is described for stripping uranium from a pregnant organic extractant comprising an alkyl pyrophosphoric acid dissolved in a substantially water-immiscible organic diluent. The organic extractant contains tetravalent uranium and an alcohol or phenol modifier in a quantity sufficient to retain substantially all the unhydrolyzed alkyl pyrophosphoric acid in solution in the diluent during stripping. The process comprises adding an oxidizing agent to the organic extractant to and thereby oxidizing the tetravalent uranium to the +6 state in the organic extractant, and contacting the organic extractant containing the uranium in the +6 state with a stripping solution comprising an aqueous solution of an alkali metal or ammonium carbonate, nonsaturated in uranium. The uranium is stripped from, the organic extractant into the stripping solution, and the resulting barren organic extractant containing substantially all of the unhydrolyzed alkyl pyrophosphoric acid dissolved in the diluent is separated from the stripping solution containing the stripped uranium, the barren extractant being suitable for recycle.

  13. Effect of various alkaline metal ions on electrochemical behavior of lead electrode in sulfuric acid solution

    NASA Astrophysics Data System (ADS)

    Hirai, Nobumitsu; Yamamoto, Yui

    2015-10-01

    The effect of various alkaline metal ions on electrochemical behavior of lead electrode in sulfuric acid solution has been investigated. It was found that "the specific anodic oxidation peak" appears at the cathodic scan in cyclic voltammogram of lead electrode in sulfuric acid solution containing Li2SO4, K2SO4, Na2SO4, Rb2SO4, or Cs2SO4. The height of the specific anodic oxidation peak varies with the alkaline sulfate in the solution; K2SO4 >> Na2SO4 > Cs2SO4 > Rb2SO4 > Li2SO4. It should be note that alkaline ions exist in lead sulfate formed on lead electrode in sulfuric acid solution containing potassium sulfate when the electrode was immersed in the solution at the rest potential for more than 1 h.

  14. An investigation into the stability and sterility of citric acid solutions used for cough reflex testing.

    PubMed

    Falconer, James R; Wu, Zimei; Lau, Hugo; Suen, Joanna; Wang, Lucy; Pottinger, Sarah; Lee, Elaine; Alazawi, Nawar; Kallesen, Molly; Gargiulo, Derryn A; Swift, Simon; Svirskis, Darren

    2014-10-01

    Citric acid is used in cough reflex testing in clinical and research settings to assess reflexive cough in patients at risk of swallowing disorders. To address a lack of knowledge in this area, this study investigated the stability and sterility of citric acid solutions. Triplicate solutions of citric acid (0.8 M) in isotonic saline were stored at 4 ± 2 °C for up to 28 days and analysed by high-performance liquid chromatography. Microbiological sterility of freshly prepared samples and bulk samples previously used for 2 weeks within the hospital was determined using a pour plate technique. Microbial survival in citric acid was determined by inoculating Staphylococcus aureus, Escherichia coli, or Candida albicans into citric acid solution and monitoring the number of colony-forming units/mL over 40 min. Citric acid solutions remained stable at 4 °C for 28 days (98.4 ± 1.8 % remained). The freshly prepared and clinical samples tested were sterile. However, viability studies revealed that citric acid solution allows for the survival of C. albicans but not for S. aureus or E. coli. The microbial survival study showed that citric acid kills S. aureus and E. coli but has no marked effect on C. albicans after 40 min. Citric acid samples at 0.8 M remained stable over the 4-week testing period, with viable microbial cells absent from samples tested. However, C. albicans has the ability to survive in citric acid solution if inadvertently introduced in practice. For this reason, in clinical and research practice it is suggested to use single-use aliquots prepared aseptically which can be stored for up to 28 days at 4 °C.

  15. SAVANNAH RIVER SITE TANK CLEANING: CORROSION RATE FOR ONE VERSUS EIGHT PERCENT OXALIC ACID SOLUTION

    SciTech Connect

    Ketusky, E.; Subramanian, K.

    2011-01-20

    Until recently, the use of oxalic acid for chemically cleaning the Savannah River Site (SRS) radioactive waste tanks focused on using concentrated 4 and 8-wt% solutions. Recent testing and research on applicable dissolution mechanisms have concluded that under appropriate conditions, dilute solutions of oxalic acid (i.e., 1-wt%) may be more effective. Based on the need to maximize cleaning effectiveness, coupled with the need to minimize downstream impacts, SRS is now developing plans for using a 1-wt% oxalic acid solution. A technology gap associated with using a 1-wt% oxalic acid solution was a dearth of suitable corrosion data. Assuming oxalic acid's passivation of carbon steel was proportional to the free oxalate concentration, the general corrosion rate (CR) from a 1-wt% solution may not be bound by those from 8-wt%. Therefore, after developing the test strategy and plan, the corrosion testing was performed. Starting with the envisioned process specific baseline solvent, a 1-wt% oxalic acid solution, with sludge (limited to Purex type sludge-simulant for this initial effort) at 75 C and agitated, the corrosion rate (CR) was determined from the measured weight loss of the exposed coupon. Environmental variations tested were: (a) Inclusion of sludge in the test vessel or assuming a pure oxalic acid solution; (b) acid solution temperature maintained at 75 or 45 C; and (c) agitation of the acid solution or stagnant. Application of select electrochemical testing (EC) explored the impact of each variation on the passivation mechanisms and confirmed the CR. The 1-wt% results were then compared to those from the 8-wt%. The immersion coupons showed that the maximum time averaged CR for a 1-wt% solution with sludge was less than 25-mils/yr for all conditions. For an agitated 8-wt% solution with sludge, the maximum time averaged CR was about 30-mils/yr at 50 C, and 86-mils/yr at 75 C. Both the 1-wt% and the 8-wt% testing demonstrated that if the sludge was removed from

  16. Electrochemical control of brightener in acid copper sulfate plating solutions

    SciTech Connect

    Bronson, M.J. . Kansas City Div.); Hawley, M.D. )

    1990-11-01

    Electrochemical methods have been evaluated that attempt the indirect measurement of the effective concentration of a brighter additive in acid copper sulfate plating baths. The procedures all employed electrodeposition of copper on a platinum working electrode under carefully controlled conditions of mass transport, time, temperature, and potential, followed by the measurement of the charge that was required to strip the copper deposit from the working electrode. The amount of charge that was required to strip the copper deposit at a given concentration of additive varied significantly from fresh to production baths and from lot to lot of the additive. The feasibility of using electrochemical methods to control brightener additive in acid copper sulfate plating baths is discussed. 3 figs., 11 refs.

  17. Interfacial structures of acidic and basic aqueous solutions

    SciTech Connect

    Tian, C.; Ji, N.; Waychunas, G.; Shen, Y.R.

    2008-10-20

    Phase-sensitive sum-frequency vibrational spectroscopy was used to study water/vapor interfaces of HCl, HI, and NaOH solutions. The measured imaginary part of the surface spectral responses provided direct characterization of OH stretch vibrations and information about net polar orientations of water species contributing to different regions of the spectrum. We found clear evidence that hydronium ions prefer to emerge at interfaces. Their OH stretches contribute to the 'ice-like' band in the spectrum. Their charges create a positive surface field that tends to reorient water molecules more loosely bonded to the topmost water layer with oxygen toward the interface, and thus enhances significantly the 'liquid-like' band in the spectrum. Iodine ions in solution also like to appear at the interface and alter the positive surface field by forming a narrow double-charge layer with hydronium ions. In NaOH solution, the observed weak change of the 'liquid-like' band and disappearance of the 'ice-like' band in the spectrum indicates that OH{sup -} ions must also have excess at the interface. How they are incorporated in the interfacial water structure is however not clear.

  18. The dissolution of quartz in dilute aqueous solutions of organic acids at 25 degree C

    SciTech Connect

    Bennett, P.C.; Melcer, M.E.; Siegel, D.I.; Hassett, J.P. )

    1988-06-01

    The dissolution of quartz in dilute aqueous solutions of organic acids at 25{degree}C and standard pressure was investigated by the batch dissolution method. The bulk dissolution rate of quartz in 20 mmole/Kg citrate solutions at pH 7 was 8 to 10 times faster than that in pure water. After 1750 hours the concentration of dissolved silica in the citrate solution was 167 {mu}mole/Kg compared to 50 {mu}mole/Kg in water and a 20 mmole/Kg solution of acetate at pH 7. Solutions of salicylic, oxalic, and humic acids also accelerated the dissolution of quartz in aqueous solution at pH 7. The rate of dissolution in organic acids decreased sharply with decreasing pH. The possibility of a silica-organic acid complex was investigated using UV-difference spectroscopy. Results suggest that dissolved silica is complexed by citrate, oxalate and pyruvate at pH 7 by an electron-donor acceptor complex, whereas no complexation occurs between silica and acetate, lactate, malonate, or succinate. Three models are proposed for the solution and surface complexation of silica by organic acid which result in the accelerated dissolution and increased solubility of quartz in organic rich water.

  19. The dissolution of quartz in dilute aqueous solutions of organic acids at 25°C

    NASA Astrophysics Data System (ADS)

    Bennett, P. C.; Melcer, M. E.; Siegel, D. I.; Hassett, J. P.

    1988-06-01

    The dissolution of quartz in dilute aqueous solutions of organic acids at 25° and standard pressure was investigated by the batch dissolution method. The bulk dissolution rate of quartz in 20 mmole/Kg citrate solutions at pH 7 was 8 to 10 times faster than that in pure water. After 1750 hours the concentration of dissolved silica in the citrate solution was 167 μmole/Kg compared to 50 μmole/Kg in water and a 20 mmole/Kg solution of acetate at pH 7. Solutions of salicylic, oxalic, and humic acids also accelerated the dissolution of quartz in aqueous solution at pH 7. The rate of dissolution in organic acids decreased sharply with decreasing pH. The possibility of a silica-organic acid complex was investigated using UV-difference spectroscopy. Results suggest that dissolved silica is complexed by citrate, oxalate and pyruvate at pH 7 by an electron-donor acceptor complex, whereas no complexation occurs between silica and acetate, lactate, malonate, or succinate. Three models are proposed for the solution and surface complexation of silica by organic acid anions which result in the accelerated dissolution and increased solubility of quartz in organic rich water.

  20. Antimicrobial and cytotoxic effects of phosphoric acid solution compared to other root canal irrigants

    PubMed Central

    PRADO, Maíra; da SILVA, Emmanuel João Nogueira Leal; DUQUE, Thais Mageste; ZAIA, Alexandre Augusto; FERRAZ, Caio Cezar Randi; de ALMEIDA, José Flávio Affonso; GOMES, Brenda Paula Figueiredo de Almeida

    2015-01-01

    Phosphoric acid has been suggested as an irrigant due to its effectiveness in removing the smear layer. Objectives : The purpose of this study was to compare the antimicrobial and cytotoxic effects of a 37% phosphoric acid solution to other irrigants commonly used in endodontics. Material and Methods : The substances 37% phosphoric acid, 17% EDTA, 10% citric acid, 2% chlorhexidine (solution and gel), and 5.25% NaOCl were evaluated. The antimicrobial activity was tested against Candida albicans, Staphylococcus aureus, Enterococcus faecalis, Escherichia coli, Actinomyces meyeri, Parvimonas micra, Porphyromonas gingivalis, and Prevotella nigrescens according to the agar diffusion method. The cytotoxicity of the irrigants was determined by using the MTT assay. Results : Phosphoric acid presented higher antimicrobial activity compared to the other tested irrigants. With regard to the cell viability, this solution showed results similar to those with 5.25% NaOCl and 2% chlorhexidine (gel and solution), whereas 17% EDTA and 10% citric acid showed higher cell viability compared to other irrigants. Conclusion : Phosphoric acid demonstrated higher antimicrobial activity and cytotoxicity similar to that of 5.25% NaOCl and 2% chlorhexidine (gel and solution). PMID:26018307

  1. The buffer capacity of airway epithelial secretions

    PubMed Central

    Kim, Dusik; Liao, Jie; Hanrahan, John W.

    2014-01-01

    The pH of airway epithelial secretions influences bacterial killing and mucus properties and is reduced by acidic pollutants, gastric reflux, and respiratory diseases such as cystic fibrosis (CF). The effect of acute acid loads depends on buffer capacity, however the buffering of airway secretions has not been well characterized. In this work we develop a method for titrating micro-scale (30 μl) volumes and use it to study fluid secreted by the human airway epithelial cell line Calu-3, a widely used model for submucosal gland serous cells. Microtitration curves revealed that HCO−3 is the major buffer. Peak buffer capacity (β) increased from 17 to 28 mM/pH during forskolin stimulation, and was reduced by >50% in fluid secreted by cystic fibrosis transmembrane conductance regulator (CFTR)-deficient Calu-3 monolayers, confirming an important role of CFTR in HCO−3 secretion. Back-titration with NaOH revealed non-volatile buffer capacity due to proteins synthesized and released by the epithelial cells. Lysozyme and mucin concentrations were too low to buffer Calu-3 fluid significantly, however model titrations of porcine gastric mucins at concentrations near the sol-gel transition suggest that mucins may contribute to the buffer capacity of ASL in vivo. We conclude that CFTR-dependent HCO−3 secretion and epithelially-derived proteins are the predominant buffers in Calu-3 secretions. PMID:24917822

  2. Environment and solute-solvent interaction effects on photo-physical behaviors of Folic acid and Folinic acid drugs

    NASA Astrophysics Data System (ADS)

    Khadem Sadigh, M.; Zakerhamidi, M. S.; Seyed Ahmadian, S. M.; Johari-Ahar, M.; Zare Haghighi, L.

    2016-12-01

    In this paper, spectral properties of Folic acid and Folinic acid as widely used drugs in the treatment of some diseases have been studied in various environments with different polarity. Our results show that the absorption, emission and stokes shifts of solute molecules depend strongly on molecular surrounding characteristics, solute-solvent interactions and, different active groups in their chemical structures. In order to investigate the contribution of specific and nonspecific interactions on various properties of drug samples, the linear solvation energy relationships concept is used. Moreover, the calculated dipole moments by means of solvatochromic method show that the high values of dipole moments in excited state are due to local intramolecular charge transfer. Furthermore, the obtained results about molecular interactions can be extended to biological systems and can indicate completely the behaviors of Folic acid and Folinic acid in polar solvents such as water in body system.

  3. Dry dilute acid pretreatment by co-currently feeding of corn stover feedstock and dilute acid solution without impregnation.

    PubMed

    He, Yanqing; Zhang, Jian; Bao, Jie

    2014-04-01

    Impregnation of lignocellulose materials with dilute acid solution is a routine operation in conventional dilute acid pretreatment. The dry dilute acid pretreatment (DDAP) at high solids content up to 70% is naturally considered to require longer impregnation time. In this study, a co-currently feeding operation of corn stover and dilute sulfuric acid solution without any impregnation was tested for DDAP. The DDAP pretreated corn stover without impregnation is found to be essentially no difference in pretreatment efficiency compared to those with impregnation in the helically agitated reactor. The yield from cellulose to ethanol in SSF again shows no obvious difference between the DDAP pretreated corn stover with and without impregnation. This study suggests that impregnation in DDAP was not necessary under the helical agitation mixing. The results provided a useful way of cost reduction and process simplification in pretreatment. PMID:24630497

  4. Dry dilute acid pretreatment by co-currently feeding of corn stover feedstock and dilute acid solution without impregnation.

    PubMed

    He, Yanqing; Zhang, Jian; Bao, Jie

    2014-04-01

    Impregnation of lignocellulose materials with dilute acid solution is a routine operation in conventional dilute acid pretreatment. The dry dilute acid pretreatment (DDAP) at high solids content up to 70% is naturally considered to require longer impregnation time. In this study, a co-currently feeding operation of corn stover and dilute sulfuric acid solution without any impregnation was tested for DDAP. The DDAP pretreated corn stover without impregnation is found to be essentially no difference in pretreatment efficiency compared to those with impregnation in the helically agitated reactor. The yield from cellulose to ethanol in SSF again shows no obvious difference between the DDAP pretreated corn stover with and without impregnation. This study suggests that impregnation in DDAP was not necessary under the helical agitation mixing. The results provided a useful way of cost reduction and process simplification in pretreatment.

  5. DYNAMIC CONDUCTIVITY MEASUREMENTS IN HUMIC AND FULVIC ACID SOLUTIONS. (R828158)

    EPA Science Inventory

    Conductivity changes of dilute aqueous humic and fulvic acids solutions were monitored after the addition of small quantities of Cu, Cd, Pb, and Zn. The solutions were stirred at a constant and reproducible rate, and measurements proceeded until stable conductivities were atta...

  6. Real-time monitoring of nucleic acid ligation in homogenous solutions using molecular beacons.

    PubMed

    Tang, Zhiwen; Wang, Kemin; Tan, Weihong; Li, Jun; Liu, Lingfeng; Guo, Qiuping; Meng, Xiangxian; Ma, Changbei; Huang, Shasheng

    2003-12-01

    Nucleic acids ligation is a vital process in the repair, replication and recombination of nucleic acids. Traditionally, it is assayed by denatured gel electrophoresis and autoradiography, which are not sensitive, and are complex and discontinuous. Here we report a new approach for ligation monitoring using molecular beacon DNA probes. The molecular beacon, designed in such a way that its sequence is complementary with the product of the ligation process, is used to monitor the nucleic acid ligation in a homogeneous solution and in real-time. Our method is fast and simple. We are able to study nucleic acids ligation kinetics conveniently and to determine the activity of DNA ligase accurately. We have studied different factors that influence DNA ligation catalyzed by T4 DNA ligase. The major advantages of our method are its ultrasensitivity, excellent specificity, convenience and real-time monitoring in homogeneous solution. This method will be widely useful for studying nucleic acids ligation process and other nucleic acid interactions.

  7. Asparagine deamidation dependence on buffer type, pH, and temperature.

    PubMed

    Pace, Amanda L; Wong, Rita L; Zhang, Yonghua Taylor; Kao, Yung-Hsiang; Wang, Y John

    2013-06-01

    The deamidation of asparagine into aspartate and isoaspartate moieties is a major pathway for the chemical degradation of monoclonal antibodies (mAbs). It can affect the shelf life of a therapeutic antibody that is not formulated or stored appropriately. A new approach to detect deamidation using ion exchange chromatography was developed that separates papain-digested mAbs into Fc and Fab fragments. From this, deamidation rates of each fragment can be calculated. To generate kinetic parameters useful in setting shelf life, buffers prepared at room temperature and then placed at the appropriate stability temperatures. Solution pH was not adjusted to the same at different temperatures. Deamidation rate at 40°C was faster in acidic buffers than in basic buffers. However, this trend is reversed at 5°C, attributed to the change in hydroxide ion concentration influenced by buffer and temperature. The apparent activation energy was higher for rates generated in an acidic buffer than in a basic buffer. The rate-pH profile for mAb1 can be deconvoluted to Fc and Fab. The Fc deamidation showed a V-shaped profile: deamidation of PENNY peptide is responsible for the rate at high-pH, whereas deamidation of a new site, Asn323, may be responsible for the rate at low-pH. The profile for Fab is a straight line without curvature.

  8. Extraction of steroidal glucosiduronic acids from aqueous solutions by anionic liquid ion-exchangers

    PubMed Central

    Mattox, Vernon R.; Litwiller, Robert D.; Goodrich, June E.

    1972-01-01

    A pilot study on the extraction of three steroidal glucosiduronic acids from water into organic solutions of liquid ion-exchangers is reported. A single extraction of a 0.5mm aqueous solution of either 11-deoxycorticosterone 21-glucosiduronic acid or cortisone 21-glucosiduronic acid with 0.1m-tetraheptylammonium chloride in chloroform took more than 99% of the conjugate into the organic phase; under the same conditions, the very polar conjugate, β-cortol 3-glucosiduronic acid, was extracted to the extent of 43%. The presence of a small amount of chloride, acetate, or sulphate ion in the aqueous phase inhibited extraction, but making the aqueous phase 4.0m with ammonium sulphate promoted extraction strongly. An increase in the concentration of ion-exchanger in the organic phase also promoted extraction. The amount of cortisone 21-glucosiduronic acid extracted by tetraheptylammonium chloride over the pH range of 3.9 to 10.7 was essentially constant. Chloroform solutions of a tertiary, a secondary, or a primary amine hydrochloride also will extract cortisone 21-glucosiduronic acid from water. The various liquid ion exchangers will extract steroidal glucosiduronic acid methyl esters from water into chloroform, although less completely than the corresponding free acids. The extraction of the glucosiduronic acids from water by tetraheptylammonium chloride occurs by an ion-exchange process; extraction of the esters does not involve ion exchange. PMID:5075264

  9. The amino acid's backup bone - storage solutions for proteomics facilities.

    PubMed

    Meckel, Hagen; Stephan, Christian; Bunse, Christian; Krafzik, Michael; Reher, Christopher; Kohl, Michael; Meyer, Helmut Erich; Eisenacher, Martin

    2014-01-01

    Proteomics methods, especially high-throughput mass spectrometry analysis have been continually developed and improved over the years. The analysis of complex biological samples produces large volumes of raw data. Data storage and recovery management pose substantial challenges to biomedical or proteomic facilities regarding backup and archiving concepts as well as hardware requirements. In this article we describe differences between the terms backup and archive with regard to manual and automatic approaches. We also introduce different storage concepts and technologies from transportable media to professional solutions such as redundant array of independent disks (RAID) systems, network attached storages (NAS) and storage area network (SAN). Moreover, we present a software solution, which we developed for the purpose of long-term preservation of large mass spectrometry raw data files on an object storage device (OSD) archiving system. Finally, advantages, disadvantages, and experiences from routine operations of the presented concepts and technologies are evaluated and discussed. This article is part of a Special Issue entitled: Computational Proteomics in the Post-Identification Era. Guest Editors: Martin Eisenacher and Christian Stephan. PMID:23722089

  10. The amino acid's backup bone - storage solutions for proteomics facilities.

    PubMed

    Meckel, Hagen; Stephan, Christian; Bunse, Christian; Krafzik, Michael; Reher, Christopher; Kohl, Michael; Meyer, Helmut Erich; Eisenacher, Martin

    2014-01-01

    Proteomics methods, especially high-throughput mass spectrometry analysis have been continually developed and improved over the years. The analysis of complex biological samples produces large volumes of raw data. Data storage and recovery management pose substantial challenges to biomedical or proteomic facilities regarding backup and archiving concepts as well as hardware requirements. In this article we describe differences between the terms backup and archive with regard to manual and automatic approaches. We also introduce different storage concepts and technologies from transportable media to professional solutions such as redundant array of independent disks (RAID) systems, network attached storages (NAS) and storage area network (SAN). Moreover, we present a software solution, which we developed for the purpose of long-term preservation of large mass spectrometry raw data files on an object storage device (OSD) archiving system. Finally, advantages, disadvantages, and experiences from routine operations of the presented concepts and technologies are evaluated and discussed. This article is part of a Special Issue entitled: Computational Proteomics in the Post-Identification Era. Guest Editors: Martin Eisenacher and Christian Stephan.

  11. Method for extracting lanthanides and actinides from acid solutions by modification of Purex solvent

    DOEpatents

    Horwitz, E.P.; Kalina, D.G.

    1984-05-21

    A process has been developed for the extraction of multivalent lanthanide and actinide values from acidic waste solutions, and for the separation of these values from fission product and other values, which utilizes a new series of neutral bi-functional extractants, the alkyl(phenyl)-N, N-dialkylcarbamoylmethylphosphine oxides, in combination with a phase modifier to form an extraction solution. The addition of the extractant to the Purex process extractant, tri-n-butylphosphate in normal paraffin hydrocarbon diluent, will permit the extraction of multivalent lanthanide and actinide values from 0.1 to 12.0 molar acid solutions.

  12. Corrosion Behavior of Alloy 22 in Oxalic Acid and Sodium Chloride Solutions

    SciTech Connect

    Day, S D; Whalen, M T; King, K J; Hust, G A; Wong, L L; Estill, J C; Rebak, R B

    2003-06-24

    Nickel based Alloy 22 (NO6022) is extensively used in aggressive industrial applications, especially due to its resistance to localized corrosion and stress corrosion cracking in high chloride environments. The purpose of this work was to characterize the anodic behavior of Alloy 22 in oxalic acid solution and to compare its behavior to sodium chloride (NaCl) solutions. Standard electrochemical tests such as polarization resistance and cyclic polarization were used. Results show that the corrosion rate of Alloy 22 in oxalic acid solutions increased rapidly as the temperature and the acid concentration increased. Extrapolation studies show that even at a concentration of 10{sup -4}M oxalic acid, the corrosion rate of Alloy 22 would be higher in oxalic acid than in 1 M NaCl solution. Alloy 22 was not susceptible to localized corrosion in oxalic acid solutions. Cyclic polarization tests in 1 M NaCl showed that Alloy 22 was susceptible to crevice corrosion at 90 C but was not susceptible at 60 C.

  13. Solute-enhanced production of gamma-valerolactone (GVL) from aqueous solutions of levulinic acid

    DOEpatents

    Dumesic, James A; Wettstein, Stephanie G; Alonso, David Martin; Gurbuz, Elif Ispir

    2015-02-24

    A method to produce levulinic acid (LA) and gamma-valerolactone (GVL) from biomass-derived cellulose or lignocellulose by selective extraction of LA using GVL and optionally converting the LA so isolated into GVL, with no purifications steps required to yield the GVL.

  14. The solvent extraction of Americium(III) by 2,6-bis[(diphenylphosphino)-methyl]pyridine N,P,P` trioxide from nitric acid and hydrochloric acid solutions

    SciTech Connect

    Bond, E.M.; Engelhardt, U.; Deere, T.P.; Rapko, B.M.; Paine, R.T.

    1997-12-31

    The liquid/liquid extractions of Am(III) from nitric acid and hydrochloric acid solutions with chloroform solutions of 2,6-bis[(diphenylphosphino)methyl]pyridine N,P,P{prime} trioxide will be described. Americium(III) extracts well from high concentration nitric acid solutions (D>3000 at 6M nitric acid) and can be back extracted from the organic phase at 0.01M Nitric Acid. Americium(III) exhibits modest extraction from hydrochloric acid solutions (D=2.2 at 5M hydrochloric acid) and can be back extracted from the organic phase at 0.1M hydrochloric acid. The ligand dependency data suggest that two ligand molecules are coordinated to americium in the nitric acid system and three ligand molecules are coordinated to the americium in the hydrochloric acid system.

  15. Time dependent inhibition of xanthine oxidase in irradiated solutions of folic acid, aminopterin and methotrexate

    SciTech Connect

    Robinson, K.; Pilot, T.F.; Meany, J.E. )

    1990-01-01

    The xanthine oxidase catalyzed oxidation of hypoxanthine was followed by monitoring the formation of uric acid at 290 nm. Inhibition of xanthine oxidase occurs in aqueous solutions of folic acid methotrexate and aminopterin. These compounds are known to dissociate upon exposure to ultraviolet light resulting in the formation of their respective 6-formylpteridine derivatives. The relative rates of dissociation were monitored spectrophotometrically by determining the absorbance of their 2,4-dinitrophenylhydrazine derivatives at 500 nm. When aqueous solutions of folic acid, aminopterin and methotrexate were exposed to uv light, a direct correlation was observed between the concentrations of the 6-formylpteridine derivatives existing in solution and the ability of these solutions to inhibit xanthine oxidase. The relative potency of the respective photolysis products were estimated.

  16. On the use of dimensionless parameters in acid-base theory: VI. The buffer capacities of equimolar binary mixtures of monovalent weak protolytes as compared to that of bivalent protolytes.

    PubMed

    Rilbe, H

    1994-05-01

    The general equation for the relative molar buffer capacity, earlier shown to be valid for bivalent acids, bases, and ampholytes, is shown to hold also for equimolar, binary mixtures of monovalent protolytes if only the parameter s = square root of K1'/4K2' is exchanged for t = s + 1/4s. The same applies to the equations for the mean valence of the two classes of protolytes. As a consequence thereof, the titration and buffer capacity curves of a bivalent protolyte are identical with those of a monovalent protolyte with a pK' value equal to the with those of a monovalent protolyte with a pK' value equal to square root of K1'K2' of the bivalent one (the isoprotic point of an ampholyte). For a hypothetical bivalent acid, base, or ampholyte with s = 1, delta pK' = log 4, this implies that the intrinsic rather than the hybrid dissociation constants are responsible for the titration and buffer capacity curves.

  17. Investigating the Fluorescence Quenching of Doxorubicin in Folic Acid Solutions and its Relation to Ligand-Targeted Nanocarriers.

    PubMed

    Husseini, Ghaleb A; Kanan, Sofian; Al-Sayah, Mohammad

    2016-02-01

    Folic acid (FA) is one of the most utilized moieties in active (ligand) drug delivery. The folate receptor is widely expressed on the surface of several cell lines and tumors; including ovarian, brain, kidney, breast, and lung cancers. During our previous experiments with Doxorubicin (Dox) encapsulated in folate-targeted micelles, we found that flow cytometry underestimated the amount of drug that accu- mulates inside cells. We attributed this effect to the quenching of Dox by FA and herein investigate this phenomenon in an attempt to obtain a correction factor that could be applied to the fluorescence of Dox in the presence of FA. Initially, we examine the effect of pH on the fluorescence spectra of FA, Dox, equimolar solutions of FA and Dox in water, HCI (0.1 M), and NaOH (0.1 M) solutions. We then measure the effect of the gradual increase of FA concentration on the fluorescence intensity of Dox in phosphate-buffered saline (PBS) solutions (pH of 7.4). Using the Stern-Volmer equation, we estimate the association constant of FA-Dox to be K(SV) = 1.5 x 10(4) M(-1). Such an association constant indicates that at the concentrations of FA used in targeted drug delivery systems, a significant concentration of Dox exists as FA-Dox complexes with a quenched fluorescence. Therefore, we conclude that when Dox is used in FA-active drug delivery systems, a correction factor is needed to predict the correct fluorescence intensity of agent in vitro and in vivo. PMID:27433596

  18. Succinic acid in aqueous solution: connecting microscopic surface composition and macroscopic surface tension.

    PubMed

    Werner, Josephina; Julin, Jan; Dalirian, Maryam; Prisle, Nønne L; Öhrwall, Gunnar; Persson, Ingmar; Björneholm, Olle; Riipinen, Ilona

    2014-10-21

    The water-vapor interface of aqueous solutions of succinic acid, where pH values and bulk concentrations were varied, has been studied using surface sensitive X-ray photoelectron spectroscopy (XPS) and molecular dynamics (MD) simulations. It was found that succinic acid has a considerably higher propensity to reside in the aqueous surface region than its deprotonated form, which is effectively depleted from the surface due to the two strongly hydrated carboxylate groups. From both XPS experiments and MD simulations a strongly increased concentration of the acid form in the surface region compared to the bulk concentration was found and quantified. Detailed analysis of the surface of succinic acid solutions at different bulk concentrations led to the conclusion that succinic acid saturates the aqueous surface at high bulk concentrations. With the aid of MD simulations the thickness of the surface layer could be estimated, which enabled the quantification of surface concentration of succinic acid as a multiple of the known bulk concentration. The obtained enrichment factors were successfully used to model the surface tension of these binary aqueous solutions using two different models that account for the surface enrichment. This underlines the close correlation of increased concentration at the surface relative to the bulk and reduced surface tension of aqueous solutions of succinic acid. The results of this study shed light on the microscopic origin of surface tension, a macroscopic property. Furthermore, the impact of the results from this study on atmospheric modeling is discussed.

  19. Acid gas absorption in aqueous solutions of mixed amines

    SciTech Connect

    Rinker, E.B.; Ashour, S.S.; Sandall, O.C.

    1996-12-31

    A mass transfer model has been developed to describe the rate of absorption (or desorption) of H{sub 2}S and CO{sub 2} in aqueous blends of a tertiary and a secondary or a primary amine. The model is based on penetration theory, and all significant chemical reactions are incorporated in the model. The reactions are taken to be reversible, with reactions involving only a proton transfer considered to be at equilibrium. The particular amines studied in this research were methyldiethanolamine (MDEA), a tertiary amine, and diethanolamine (DEA), a secondary amine. Key physicochemical data needed in the model, such as diffusion coefficients, kinetic rate constants, and gas solubilities, were measured. Experimental absorption rates of CO{sub 2} and H{sub 2}S were measured in a model gas-liquid contacting device and were compared with model predictions. Experiments were carried out for single amine solutions (both MDEA and DEA) and for amine blends.

  20. Formation of aromatic compounds from carbohydrates. X reaction of xylose, glucose, and glucuronic acid in acidic solution at 300C

    SciTech Connect

    Theander, O.; Nelson, D.A.; Hallen, R.T.

    1987-04-01

    For several years our respective groups have investigated the formation of aromatic compounds from carbohydrates in aqueous solution at various pH-values under reflux or hydrothermolytic conditions. For instance, previous papers in this series concerned the degradation of hexoses, pentoses, erythrose, dihydroxyacetone, and hexuronic acids to phenolic and enolic components. Of particular interest were the isolation and identification of catechols, an acetophenone, and chromones from pentoses and hexuronic acids at pH 4.5. The formation of these compounds, as well as reductic acid, was found to be more pronounced than that of 2-furaldehyde under acidic conditions. The aromatic precursors of 3 and 4 were also isolated from these reaction mixtures. This is in contrast to the high yields of 2 obtained from pentoses and hexuronic acids at very low pH.

  1. Dissolution of Simulated and Radioactive Savannah River Site High-Level Waste Sludges with Oxalic Acid & Citric Acid Solutions

    SciTech Connect

    STALLINGS, MARY

    2004-07-08

    This report presents findings from tests investigating the dissolution of simulated and radioactive Savannah River Site sludges with 4 per cent oxalic acid and mixtures of oxalic and citric acid previously recommended by a Russian team from the Khlopin Radium Institute and the Mining and Chemical Combine (MCC). Testing also included characterization of the simulated and radioactive waste sludges. Testing results showed the following: Dissolution of simulated HM and PUREX sludges with oxalic and citric acid mixtures at SRTC confirmed general trends reported previously by Russian testing. Unlike the previous Russian testing six sequential contacts of a mixture of oxalic acid citric acids at a 2:1 ratio (v/w) of acid to sludge did not produce complete dissolution of simulated HM and PUREX sludges. We observed that increased sludge dissolution occurred at a higher acid to sludge ratio, 50:1 (v/w), compared to the recommended ratio of 2:1 (v/w). We observed much lower dissolution of aluminum in a simulated HM sludge by sodium hydroxide leaching. We attribute the low aluminum dissolution in caustic to the high fraction of boehmite present in the simulated sludge. Dissolution of HLW sludges with 4 per cent oxalic acid and oxalic/citric acid followed general trends observed with simulated sludges. The limited testing suggests that a mixture of oxalic and citric acids is more efficient for dissolving HM and PUREX sludges and provides a more homogeneous dissolution of HM sludge than oxalic acid alone. Dissolution of HLW sludges in oxalic and oxalic/citric acid mixtures produced residual sludge solids that measured at higher neutron poison to equivalent 235U weight ratios than that in the untreated sludge solids. This finding suggests that residual solids do not present an increased nuclear criticality safety risk. Generally the neutron poison to equivalent 235U weight ratios of the acid solutions containing dissolved sludge components are lower than those in the untreated

  2. Ultrasonic Studies of 4-Aminobutyric Acid in Aqueous Metformin Hydrochloride Solutions at Different Temperatures

    NASA Astrophysics Data System (ADS)

    Rajagopal, K.; Jayabalakrishnan, S. S.

    2010-12-01

    Ultrasonic speeds and density data of 4-aminobutyric acid in 0.05 M, 0.10 M, and 0.15 M aqueous metformin hydrochloride (MFHCl) solutions are measured at 308.15 K, 313.15 K, and 318.15 K. The isentropic compressibility ( k S ), the change in isentropic compressibility (Δ k S ), the relative change in isentropic compressibility ({Δ k_S/k_S^0}), the apparent molal compressibility ({k_φ}), the limiting apparent molal compressibility ({k_φ^0 }), the transfer limiting apparent molal compressibility ({Δ k_φ^0}), the hydration number ( n H), and the pair and triplet interaction parameters ( k AH, k AHH) are estimated. The above parameters are used to interpret the solute-solute and solute-solvent interactions of 4-aminobutyric acid in aqueous MFHCl solutions.

  3. Reaction behavior of Ni-Re alloys during direct current polarization in sulfuric acid solutions

    NASA Astrophysics Data System (ADS)

    Bryukvin, V. A.; Elemesov, T. B.; Levchuk, O. M.; Bol'shikh, A. O.

    2016-01-01

    The macrokinetic regularities of the reactivity of synthesized Ni-Re (20 and 60 wt %) alloys in a sulfuric acid solution (100 g/L, 25-40°C) during direct current polarization are studied using physicochemical methods. The phase composition of the synthesized alloys is determined by the formation of solid solutions as a function of the initial Ni/Re weight ratio. These are two types of nickel solid solutions (Ni16Re0.2 and Ni14Re0.9) and one rhenium solution (Ni1.1Re). These solid solutions are anodically oxidized in the sequence of their structural rearrangement Ni16Re0.2 → Ni14Re0.9 → Ni1.1Re with a combined transition of the metals into an electrolyte solution. These solid solutions provide the reduction of Ni3+ to Ni2+ due to the depolarization ability of rhenium, being their component.

  4. Methylene blue adsorption from aqueous solution by activated carbon: effect of acidic and alkaline solution treatments.

    PubMed

    Ijagbemi, Christianah O; Chun, Ji I; Han, Da H; Cho, Hye Y; O, Se J; Kim, Dong S

    2010-01-01

    The removal of Methylene Blue (MB) from aqueous solution using activated carbon (AC) has been investigated. Adsorption experiments were conducted and the maximum adsorption capacity was determined. The effect of experimental parameters such as pH, dye concentration and temperature were studied on the adsorption process. Equilibrium data were mathematically modeled using the Langmuir and Freundlich adsorption models to describe the equilibrium isotherms at different dye concentrations and temperature. Parameters of best-fit model were calculated and discussed. To understand the mechanism of adsorption, kinetic models were employed to follow the adsorption processes; the pseudo-first-order best described the adsorption of MB onto AC. It was found that pH plays a major role in the adsorption process; adsorption capacity was influenced by the physical and surface chemical properties of carbon and the pH of the solution. 99.0% MB removal was achieved at equilibrium.

  5. Metabolic engineering of yeast to produce fatty acid-derived biofuels: bottlenecks and solutions.

    PubMed

    Sheng, Jiayuan; Feng, Xueyang

    2015-01-01

    Fatty acid-derived biofuels can be a better solution than bioethanol to replace petroleum fuel, since they have similar energy content and combustion properties as current transportation fuels. The environmentally friendly microbial fermentation process has been used to synthesize advanced biofuels from renewable feedstock. Due to their robustness as well as the high tolerance to fermentation inhibitors and phage contamination, yeast strains such as Saccharomyces cerevisiae and Yarrowia lipolytica have attracted tremendous attention in recent studies regarding the production of fatty acid-derived biofuels, including fatty acids, fatty acid ethyl esters, fatty alcohols, and fatty alkanes. However, the native yeast strains cannot produce fatty acids and fatty acid-derived biofuels in large quantities. To this end, we have summarized recent publications in this review on metabolic engineering of yeast strains to improve the production of fatty acid-derived biofuels, identified the bottlenecks that limit the productivity of biofuels, and categorized the appropriate approaches to overcome these obstacles. PMID:26106371

  6. Metabolic engineering of yeast to produce fatty acid-derived biofuels: bottlenecks and solutions

    PubMed Central

    Sheng, Jiayuan; Feng, Xueyang

    2015-01-01

    Fatty acid-derived biofuels can be a better solution than bioethanol to replace petroleum fuel, since they have similar energy content and combustion properties as current transportation fuels. The environmentally friendly microbial fermentation process has been used to synthesize advanced biofuels from renewable feedstock. Due to their robustness as well as the high tolerance to fermentation inhibitors and phage contamination, yeast strains such as Saccharomyces cerevisiae and Yarrowia lipolytica have attracted tremendous attention in recent studies regarding the production of fatty acid-derived biofuels, including fatty acids, fatty acid ethyl esters, fatty alcohols, and fatty alkanes. However, the native yeast strains cannot produce fatty acids and fatty acid-derived biofuels in large quantities. To this end, we have summarized recent publications in this review on metabolic engineering of yeast strains to improve the production of fatty acid-derived biofuels, identified the bottlenecks that limit the productivity of biofuels, and categorized the appropriate approaches to overcome these obstacles. PMID:26106371

  7. Precipitation pathways for ferrihydrite formation in acidic solutions

    DOE PAGES

    Zhu, Mengqiang; Khalid, Syed; Frandsen, Cathrine; Wallace, Adam F.; Legg, Benjamin; Zhang, Hengzhong; Morup, Steen; Banfield, Jillian F.; Waychunas, Glenn A.

    2015-10-03

    In this study, iron oxides and oxyhydroxides form via Fe3+ hydrolysis and polymerization in many aqueous environments, but the pathway from Fe3+ monomers to oligomers and then to solid phase nuclei is unknown. In this work, using combined X-ray, UV–vis, and Mössbauer spectroscopic approaches, we were able to identify and quantify the long-time sought ferric speciation over time during ferric oxyhydroxide formation in partially-neutralized ferric nitrate solutions ([Fe3+] = 0.2 M, 1.8 < pH < 3). Results demonstrate that Fe exists mainly as Fe(H2O)63+, μ-oxo aquo dimers and ferrihydrite, and that with time, the μ-oxo dimer decreases while the othermore » two species increase in their concentrations. No larger Fe oligomers were detected. Given that the structure of the μ-oxo dimer is incompatible with those of all Fe oxides and oxyhydroxides, our results suggest that reconfiguration of the μ-oxo dimer structure occurs prior to further condensation leading up to the nucleation of ferrihydrite. The structural reconfiguration is likely the rate-limiting step involved in the nucleation process.« less

  8. Precipitation pathways for ferrihydrite formation in acidic solutions

    SciTech Connect

    Zhu, Mengqiang; Khalid, Syed; Frandsen, Cathrine; Wallace, Adam F.; Legg, Benjamin; Zhang, Hengzhong; Morup, Steen; Banfield, Jillian F.; Waychunas, Glenn A.

    2015-10-03

    In this study, iron oxides and oxyhydroxides form via Fe3+ hydrolysis and polymerization in many aqueous environments, but the pathway from Fe3+ monomers to oligomers and then to solid phase nuclei is unknown. In this work, using combined X-ray, UV–vis, and Mössbauer spectroscopic approaches, we were able to identify and quantify the long-time sought ferric speciation over time during ferric oxyhydroxide formation in partially-neutralized ferric nitrate solutions ([Fe3+] = 0.2 M, 1.8 < pH < 3). Results demonstrate that Fe exists mainly as Fe(H2O)63+, μ-oxo aquo dimers and ferrihydrite, and that with time, the μ-oxo dimer decreases while the other two species increase in their concentrations. No larger Fe oligomers were detected. Given that the structure of the μ-oxo dimer is incompatible with those of all Fe oxides and oxyhydroxides, our results suggest that reconfiguration of the μ-oxo dimer structure occurs prior to further condensation leading up to the nucleation of ferrihydrite. The structural reconfiguration is likely the rate-limiting step involved in the nucleation process.

  9. Precipitation pathways for ferrihydrite formation in acidic solutions

    NASA Astrophysics Data System (ADS)

    Zhu, Mengqiang; Frandsen, Cathrine; Wallace, Adam F.; Legg, Benjamin; Khalid, Syed; Zhang, Hengzhong; Mørup, Steen; Banfield, Jillian F.; Waychunas, Glenn A.

    2016-01-01

    Iron oxides and oxyhydroxides form via Fe3+ hydrolysis and polymerization in many aqueous environments, but the pathway from Fe3+ monomers to oligomers and then to solid phase nuclei is unknown. In this work, using combined X-ray, UV-vis, and Mössbauer spectroscopic approaches, we were able to identify and quantify the long-time sought ferric speciation over time during ferric oxyhydroxide formation in partially-neutralized ferric nitrate solutions ([Fe3+] = 0.2 M, 1.8 < pH < 3). Results demonstrate that Fe exists mainly as Fe(H2O)63+, μ-oxo aquo dimers and ferrihydrite, and that with time, the μ-oxo dimer decreases while the other two species increase in their concentrations. No larger Fe oligomers were detected. Given that the structure of the μ-oxo dimer is incompatible with those of all Fe oxides and oxyhydroxides, our results suggest that reconfiguration of the μ-oxo dimer structure occurs prior to further condensation leading up to the nucleation of ferrihydrite. The structural reconfiguration is likely the rate-limiting step involved in the nucleation process.

  10. Extraction of palladium from acidic solutions with the use of carbon adsorbents

    SciTech Connect

    O.N. Kononova; N.G. Goryaeva; N.B. Dostovalova; S.V. Kachin; A.G. Kholmogorov

    2007-08-15

    We studied the sorption of palladium(II) on LKAU-4, LKAU-7, and BAU carbon adsorbents from model hydrochloric acid solutions and the solutions of spent palladium-containing catalysts. It was found that sorbents based on charcoal (BAU) and anthracite (LKAU-4) were characterized by high sorption capacities for palladium. The kinetics of the saturation of carbon adsorbents with palladium(II) ions was studied, and it was found that more than 60% of the initial amount of Pd(II) was recovered in a 1-h contact of an adsorbent with a model solution. This value for the solutions of spent catalysts was higher than 35%.

  11. Capillary electrophoresis analysis of hydrolysis, isomerization and enantiomerization of aspartyl model tripeptides in acidic and alkaline solution.

    PubMed

    De Boni, Silvia; Scriba, Gerhard K E

    2007-01-01

    In order to investigate the degradation of two aspartyl tripeptides, Gly-Asp-PheNH2 and Phe-Asp-GlyNH2 in solution capillary, electrophoresis methods were developed and validated. Separation of most degradation products including those arising from isomerization and enantiomerization of the Asp residues was achieved in a 50 mM sodium phosphate buffer, pH 3.0. Resolution of comigrating compounds could be achieved by addition of cyclodextrins to the background electrolyte. For tripeptide derivatives the assays were linear in the range of 0.015-3.0 mmol/l. Some dipeptides and amino acids exhibited a narrower linear range due to low UV absorbance. The limits of detection were in the range of 0.005-0.1 mmol/l. Incubation of the model peptides was carried out at pH 2 and 10. At pH 2, degradation of the peptides proceeded via C-terminal deamidation and peptide backbone hydrolysis. In contrast, isomerization and enantiomerization were observed in combination with deamidation at pH 10. Generally, degradation of Phe-Asp-GlyNH2 proceeded faster compared to Gly-Asp-PheNH2 due to steric hindrance by the phenyl side chain.

  12. Separation of thorium and uranium in nitric acid solution using silica based anion exchange resin.

    PubMed

    Chen, Yanliang; Wei, Yuezhou; He, Linfeng; Tang, Fangdong

    2016-09-30

    To separate thorium and uranium in nitric acid solution using anion exchange process, a strong base silica-based anion exchange resin (SiPyR-N4) was synthesized. Batch experiments were conducted and the separation factor of thorium and uranium in 9M nitric acid was about 10. Ion exchange chromatography was applied to separate thorium and uranium in different ratios. Uranium could be eluted by 9M nitric acid and thorium was eluted by 0.1M nitric acid. It was proved that thorium and uranium can be separated and recovered successfully by this method.

  13. Comparison of XAD macroporous resins for the concentration of fulvic acid from aqueous solution

    USGS Publications Warehouse

    Aiken, G.R.

    1979-01-01

    Five macroreticular, nonlonlc AmberlHe XAD resins were evaluated for concentration and Isolation of fulvlc acid from aqueous solution. The capacity of each resin for fulvlc acid was measured by both batch and column techniques. Elution efficiencies were determined by desorptlon with 0.1 N NaOH. Highest recoveries were obtained with the acrylic ester resins which proved to be most efficient for both adsorption and elution of fulvlc acid. Compared to the acrylic ester resins, usefulness of the styrene dvlnybenzene resins to remove fulvlc acid is limited because of slow diffusion-controlled adsorption and formation of charge-transfer complexes, which hinders elution. ?? 1979 American Chemical Society.

  14. Separation of thorium and uranium in nitric acid solution using silica based anion exchange resin.

    PubMed

    Chen, Yanliang; Wei, Yuezhou; He, Linfeng; Tang, Fangdong

    2016-09-30

    To separate thorium and uranium in nitric acid solution using anion exchange process, a strong base silica-based anion exchange resin (SiPyR-N4) was synthesized. Batch experiments were conducted and the separation factor of thorium and uranium in 9M nitric acid was about 10. Ion exchange chromatography was applied to separate thorium and uranium in different ratios. Uranium could be eluted by 9M nitric acid and thorium was eluted by 0.1M nitric acid. It was proved that thorium and uranium can be separated and recovered successfully by this method. PMID:27614730

  15. Measurement of pH by NMR Spectroscopy in Concentrated Aqueous Fluoride Buffers

    PubMed Central

    Gerken, James B.

    2010-01-01

    An NMR spectroscopic technique has been developed to give rapid, accurate pH measurements on tenth-milliliter samples of concentrated acidic aqueous solutions buffered by fluoride ion in the pH 1.5 – 4.5 range. The fluoride 19F chemical shift has been calibrated as a function of pH at 0.1 and 1.0 M concentration by reference to an internal 3-fluoropyridine standard. Subsequent measurements of fluoride buffer pH required no additives and only two NMR spectra in the presence of an external reference standard. PMID:21278857

  16. Common data buffer

    NASA Technical Reports Server (NTRS)

    Byrne, F.

    1981-01-01

    Time-shared interface speeds data processing in distributed computer network. Two-level high-speed scanning approach routes information to buffer, portion of which is reserved for series of "first-in, first-out" memory stacks. Buffer address structure and memory are protected from noise or failed components by error correcting code. System is applicable to any computer or processing language.

  17. Isotherm-Based Thermodynamic Models for Solute Activities of Organic Acids with Consideration of Partial Dissociation.

    PubMed

    Nandy, Lucy; Ohm, Peter B; Dutcher, Cari S

    2016-06-23

    Organic acids make up a significant fraction of the organic mass in atmospheric aerosol particles. The calculation of gas-liquid-solid equilibrium partitioning of the organic acid is therefore critical for accurate determination of atmospheric aerosol physicochemical properties and processes such as new particle formation and activation to cloud condensation nuclei. Previously, an adsorption isotherm-based statistical thermodynamic model was developed for capturing solute concentration-activity relationships for multicomponent aqueous solutions over the entire concentration range (Dutcher et al. J. Phys. Chem. C/A 2011, 2012, 2013), with model parameters for energies of adsorption successfully related to dipole-dipole electrostatic forces in solute-solvent and solvent-solvent interactions for both electrolytes and organics (Ohm et al. J. Phys. Chem. A 2015). However, careful attention is needed for weakly dissociating semivolatile organic acids. Dicarboxylic acids, such as malonic acid and glutaric acid are treated here as a mixture of nondissociated organic solute (HA) and dissociated solute (H(+) + A(-)). It was found that the apparent dissociation was greater than that predicted by known dissociation constants alone, emphasizing the effect of dissociation on osmotic and activity coefficient predictions. To avoid additional parametrization from the mixture approach, an expression was used to relate the Debye-Hückel hard-core collision diameter to the adjustable solute-solvent intermolecular distance. An improved reference state treatment for electrolyte-organic aqueous mixtures, such as that observed here with partial dissociation, has also been proposed. This work results in predictive correlations for estimation of organic acid and water activities for which there is little or no activity data.

  18. Isotherm-Based Thermodynamic Models for Solute Activities of Organic Acids with Consideration of Partial Dissociation.

    PubMed

    Nandy, Lucy; Ohm, Peter B; Dutcher, Cari S

    2016-06-23

    Organic acids make up a significant fraction of the organic mass in atmospheric aerosol particles. The calculation of gas-liquid-solid equilibrium partitioning of the organic acid is therefore critical for accurate determination of atmospheric aerosol physicochemical properties and processes such as new particle formation and activation to cloud condensation nuclei. Previously, an adsorption isotherm-based statistical thermodynamic model was developed for capturing solute concentration-activity relationships for multicomponent aqueous solutions over the entire concentration range (Dutcher et al. J. Phys. Chem. C/A 2011, 2012, 2013), with model parameters for energies of adsorption successfully related to dipole-dipole electrostatic forces in solute-solvent and solvent-solvent interactions for both electrolytes and organics (Ohm et al. J. Phys. Chem. A 2015). However, careful attention is needed for weakly dissociating semivolatile organic acids. Dicarboxylic acids, such as malonic acid and glutaric acid are treated here as a mixture of nondissociated organic solute (HA) and dissociated solute (H(+) + A(-)). It was found that the apparent dissociation was greater than that predicted by known dissociation constants alone, emphasizing the effect of dissociation on osmotic and activity coefficient predictions. To avoid additional parametrization from the mixture approach, an expression was used to relate the Debye-Hückel hard-core collision diameter to the adjustable solute-solvent intermolecular distance. An improved reference state treatment for electrolyte-organic aqueous mixtures, such as that observed here with partial dissociation, has also been proposed. This work results in predictive correlations for estimation of organic acid and water activities for which there is little or no activity data. PMID:27222917

  19. Bis(mesitoyl)phosphinic acid: photo-triggered release of metaphosphorous acid in solution.

    PubMed

    Fast, David E; Zalibera, Michal; Lauer, Andrea; Eibel, Anna; Schweigert, Caroline; Kelterer, Anne-Marie; Spichty, Martin; Neshchadin, Dmytro; Voll, Dominik; Ernst, Hanna; Liang, Yu; Dietliker, Kurt; Unterreiner, Andreas-Neil; Barner-Kowollik, Christopher; Grützmacher, Hansjörg; Gescheidt, Georg

    2016-08-01

    Bis(mesitoyl)phosphinic acid and its sodium salt display a unique photo-induced reactivity: both derivatives stepwise release two mesitoyl radicals and, remarkably, metaphosphorous acid (previously postulated as transient species in the gas phase), providing a new phosphorus-based reagent. PMID:27431207

  20. Extraction of gallium(III) from hydrochloric acid solutions by trioctylammonium-based mixed ionic liquids.

    PubMed

    Katsuta, Shoichi; Okai, Miho; Yoshimoto, Yuki; Kudo, Yoshihiro

    2012-01-01

    The extractabilities of aluminium(III), gallium(III), and indium(III) from hydrochloric acid solutions were investigated using a mixture of two protic ionic liquids, trioctylammonium bis(trifluoromethanesulfonyl)amide ([TOAH][NTf(2)]) and trioctylammonium nitrate ([TOAH][NO(3)]). At a HCl concentration of 4 mol L(-1) or more, gallium(III) was nearly quantitatively extracted and the extractability order was Ga > Al > In. The extractability of gallium(III) increased with increasing [TOAH][NO(3)] content in the mixed ionic liquid. The extracted gallium(III) was quantitatively stripped with aqueous nitric acid solutions. The separation and recovery of gallium(III) from hydrochloric acid solutions containing excess indium(III) was demonstrated using the mixed ionic liquid.

  1. Effect of Mineral Admixtures on Resistance to Sulfuric Acid Solution of Mortars with Quaternary Binders

    NASA Astrophysics Data System (ADS)

    Makhloufi, Zoubir; Bederina, Madani; Bouhicha, Mohamed; Kadri, El-Hadj

    This research consists to study the synergistic action of three mineral additions simultaneously added to the cement. This synergistic effect has a positive effect on the sustainability of limestone mortars. Tests were performed on mortars based on crushed limestone sand and manufactured by five quaternary binders (ordinary Portland cement and CPO mixed simultaneously with filler limestone, blast-furnace and natural pozzolan). The purpose of this research was to identify the resistance of five different mortars to the solution of sulfuric acid. Changes in weight loss and compressive strength measured at 30, 60, 90, 120 and 180 days for each acid solution were studied. We followed up on the change in pH of the sulfuric acid solution at the end of each month up to 180 days.

  2. Formation of amino acids by cobalt-60 irradiation of hydrogen cyanide solutions

    NASA Technical Reports Server (NTRS)

    Sweeney, M. A.; Toste, A. P.; Ponnamperuma, C.

    1976-01-01

    Experiments were conducted to study the pathway for the prebiotic origin of amino acids from hydrogen cyanide (HCN) under the action of ionizing radiation considered as an effective source of energy on the primitive earth. The irradiations were performed in a cobalt-60 source with a dose rate of 200,000 rad/hr. Seven naturally occurring amino acids are identified among the products formed by the hydrolysis of gamma-irradiated solutions of HCN: glycine, alanine, valine, serine, threonine, aspartic acid, and glutamic acid. The identity of these amino acids is established by gas chromatography and mass spectrometry. Control experiments provided evidence that the amino acids are not the result of contamination.

  3. Gamma-irradiation of malic acid in aqueous solutions. [prebiotic significance

    NASA Technical Reports Server (NTRS)

    Negron-Mendoza, A.; Graff, R. L.; Ponnamperuma, C.

    1980-01-01

    The gamma-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the nonvolatile products. Thin layer chromatography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the gamma-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

  4. Standard enthalpies of formation of α-aminobutyric acid and products of its dissociation in an aqueous solution

    NASA Astrophysics Data System (ADS)

    Lytkin, A. I.; Chernikov, V. V.; Krutova, O. N.

    2016-08-01

    Heats of solution of crystalline α-aminobutyric acid in water and in aqueous solutions of potassium hydroxide at 298.15 K are measured by means of direct calorimetry. Standard enthalpies of formation of the amino acid and products of its dissociation in an aqueous solution are calculated.

  5. Chemical modification of amino acids by atmospheric-pressure cold plasma in aqueous solution

    NASA Astrophysics Data System (ADS)

    Takai, Eisuke; Kitamura, Tsuyoshi; Kuwabara, Junpei; Ikawa, Satoshi; Yoshizawa, Shunsuke; Shiraki, Kentaro; Kawasaki, Hideya; Arakawa, Ryuichi; Kitano, Katsuhisa

    2014-07-01

    Plasma medicine is an attractive new research area, but the principles of plasma modification of biomolecules in aqueous solution remain elusive. In this study, we investigated the chemical effects of atmospheric-pressure cold plasma on 20 naturally occurring amino acids in aqueous solution. High-resolution mass spectrometry revealed that chemical modifications of 14 amino acids were observed after plasma treatment: (i) hydroxylation and nitration of aromatic rings in tyrosine, phenylalanine and tryptophan; (ii) sulfonation and disulfide linkage formation of thiol groups in cysteine; (iii) sulfoxidation of methionine and (iv) amidation and ring-opening of five-membered rings in histidine and proline. A competitive reaction experiment using 20 amino acids demonstrated that sulfur-containing and aromatic amino acids were preferentially decreased by the plasma treatment. These data provide fundamental information for elucidating the mechanism of protein inactivation for biomedical plasma applications.

  6. Phase equilibria in a system of aqueous arginine with an octane solution of sulfonic acid

    NASA Astrophysics Data System (ADS)

    Kuvaeva, Z. I.; Koval'chuk, I. V.; Vodop'yanova, L. A.; Soldatov, V. S.

    2013-05-01

    The extraction of arginine (Arg) from aqueous salt (0.1 M NaCl) solutions with a sulfo extractant in a wide range of pH values and amino acid concentrations was studied. The 0.1 M solution of dinonylnaphthalenesulfonic acid (HD) in octane was used as an extractant. The degree of extraction was found to be high at pH 0.8-9.0. This can be explained by the effect of additional intermolecular interactions in the extractant phase involving the guanidine group of Arg.

  7. Dissolved oxygen alteration of the spectrophotometric analysis and quantification of nucleic acid solutions.

    PubMed

    Doshi, Rupak; Day, Philip J R; Tirelli, Nicola

    2009-04-01

    Nucleic acids are routinely and readily analysed using the A(260)/A(280) ratio, although this method is known to be prone to erroneous results owing to contaminants in solution that absorb at similar wavelengths. The aim of the present review, while highlighting the problems and alternatives of using UV spectrophotometry for nucleic acid measurements, is to bring forth an observational result from our recent studies, namely that DO (dissolved oxygen) and nitrogen can alter the A(260) of aqueous DNA solutions. Our finding is of importance because DO is highly variable between protocols and storage conditions of DNA preparations. The physicochemical nature of the oxygen-DNA interactions is briefly discussed.

  8. Measurement of partial vapor pressure of ammonia over acid ammonium sulfate solutions by an integral method

    NASA Astrophysics Data System (ADS)

    Koutrakis, P.; Aurian-BlǎJeni, B.

    1993-02-01

    We present a simple, integral, passive method for measuring partial vapor pressure. Integral methods are useful tools when dealing with very low concentrations because collection over extended periods increases the analytical sensitivity. Passive methods have the advantage of not introducing constraints external to the system. The principle of the method used here is to selectively react the substance in the atmosphere over a solution with an immobilized coating on an appropriate support. The reaction product is not volatile, but is soluble and can be extracted in an appropriate solvent and analyzed. The method has been applied to measuring the vapor pressure of ammonia over aqueous solutions. The vapor pressure over ammonium sulfate solutions depends on the acidity of the solutions as well as on the salt concentration. The dependence can be explained with a simple model. Furthermore, using the same model, we calculated the ammonia vapor pressure above different ammonium sulfate/sulfuric acid aqueous solutions as a function of sulfate molarity and percentage of sulfuric acid. The results from the calculations suggest that for ambient ammonia concentrations less than 10 ppb, acid sulfate aerosols are not completely neutralized.

  9. Stability of antimicrobial activity of peracetic acid solutions used in the final disinfection process.

    PubMed

    Costa, Solange Alves da Silva; Paula, Olívia Ferreira Pereira de; Silva, Célia Regina Gonçalves E; Leão, Mariella Vieira Pereira; Santos, Silvana Soléo Ferreira dos

    2015-01-01

    The instruments and materials used in health establishments are frequently exposed to microorganism contamination, and chemical products are used before sterilization to reduce occupational infection. We evaluated the antimicrobial effectiveness, physical stability, and corrosiveness of two commercial formulations of peracetic acid on experimentally contaminated specimens. Stainless steel specimens were contaminated with Staphylococcus aureus, Escherichia coli, Candida albicans, blood, and saliva and then immersed in a ready peracetic acid solution: 2% Sekusept Aktiv (SA) or 0.25% Proxitane Alpha (PA), for different times. Then, washes of these instruments were plated in culture medium and colony-forming units counted. This procedure was repeated six times per day over 24 non-consecutive days. The corrosion capacity was assessed with the mass loss test, and the concentration of peracetic acid and pH of the solutions were measured with indicator tapes. Both SA and PA significantly eliminated microorganisms; however, the SA solution was stable for only 4 days, whereas PA remained stable throughout the experiment. The concentration of peracetic acid in the SA solutions decreased over time until the chemical was undetectable, although the pH remained at 5. The PA solution had a concentration of 500-400 mg/L and a pH of 2-3. Neither formulation induced corrosion and both reduced the number of microorganisms (p = 0.0001). However, the differences observed in the performance of each product highlight the necessity of establishing a protocol for optimizing the use of each one.

  10. Stability of antimicrobial activity of peracetic acid solutions used in the final disinfection process.

    PubMed

    Costa, Solange Alves da Silva; Paula, Olívia Ferreira Pereira de; Silva, Célia Regina Gonçalves E; Leão, Mariella Vieira Pereira; Santos, Silvana Soléo Ferreira dos

    2015-01-01

    The instruments and materials used in health establishments are frequently exposed to microorganism contamination, and chemical products are used before sterilization to reduce occupational infection. We evaluated the antimicrobial effectiveness, physical stability, and corrosiveness of two commercial formulations of peracetic acid on experimentally contaminated specimens. Stainless steel specimens were contaminated with Staphylococcus aureus, Escherichia coli, Candida albicans, blood, and saliva and then immersed in a ready peracetic acid solution: 2% Sekusept Aktiv (SA) or 0.25% Proxitane Alpha (PA), for different times. Then, washes of these instruments were plated in culture medium and colony-forming units counted. This procedure was repeated six times per day over 24 non-consecutive days. The corrosion capacity was assessed with the mass loss test, and the concentration of peracetic acid and pH of the solutions were measured with indicator tapes. Both SA and PA significantly eliminated microorganisms; however, the SA solution was stable for only 4 days, whereas PA remained stable throughout the experiment. The concentration of peracetic acid in the SA solutions decreased over time until the chemical was undetectable, although the pH remained at 5. The PA solution had a concentration of 500-400 mg/L and a pH of 2-3. Neither formulation induced corrosion and both reduced the number of microorganisms (p = 0.0001). However, the differences observed in the performance of each product highlight the necessity of establishing a protocol for optimizing the use of each one. PMID:25715037

  11. Recovery of water and acid from leach solutions using direct contact membrane distillation.

    PubMed

    Kesieme, Uchenna K; Milne, Nicholas; Cheng, Chu Yong; Aral, Hal; Duke, Mikel

    2014-01-01

    This paper describes for the first time the use of direct contact membrane distillation (DCMD) for acid and water recovery from a real leach solution generated by a hydrometallurgical plant. The leach solutions considered contained H2SO4 or HCl. In all tests the temperature of the feed solution was kept at 60 °C. The test work showed that fluxes were within the range of 18-33 kg/m(2)/h and 15-35 kg/m(2)/h for the H2SO4 and HCl systems, respectively. In the H2SO4 leach system, the final concentration of free acid in the sample solution increased on the concentrate side of the DCMD system from 1.04 M up to 4.60 M. The sulfate separation efficiency was over 99.9% and overall water recovery exceeded 80%. In the HCl leach system, HCl vapour passed through the membrane from the feed side to the permeate. The concentration of HCl captured in the permeate was about 1.10 M leaving behind only 0.41 M in the feed from the initial concentration of 2.13 M. In all the experiments, salt rejection was >99.9%. DCMD is clearly viable for high recovery of high quality water and concentrated H2SO4 from spent sulfuric acid leach solution where solvent extraction could then be applied to recover the sulfuric acid and metals. While HCl can be recovered for reuse using only DCMD.

  12. New crystallization of fatty acids from aqueous ethanol solution combined with liquid-liquid extraction

    SciTech Connect

    Maeda, Kouji; Nomura, Yoshihisa; Tai, Kimihiko; Ueno, Yoshitaka; Fukui, Keisuke; Hirota, Syouji

    1999-06-01

    A new separation process of saturated fatty acids (lauric acid-myristic acid) using crystallization from an aqueous ethanol solution has been examined. There were two vessels in this separation process: an extraction vessel and a crystallization vessel. The fatty acids in the aqueous phase were first extracted from their organic phase (melt) in the extraction vessel. The fatty acids in the aqueous phase were continuously introduced to the crystallization vessel, and then the fatty acids were crystallized there. The crystals of the fatty acids were collected continuously above the aqueous phase in the crystallization vessel. In this process, the yield and the purity of the crystals over time were measured, and it was found that the purity of lauric acid increased unsteadily up to 0.98 mole fraction of lauric acid with an increase in the yield of the low yield range. The mole fraction of ethanol in the aqueous phase could be significant to control the relationship between the yield and the purity of the crystals. Three different mole fractions of lauric acid in the organic phase were used to be separated in this process. Moreover, the authors have considered the effective separations of this process, and the maximum yield and purity of the crystals have been estimated by a simple mass balance.

  13. Electrochemical formation of hydroxide for enhancing carbon dioxide and acid gas uptake by a solution

    DOEpatents

    Rau, Gregory Hudson

    2012-05-15

    A system is described for forming metal hydroxide from a metal carbonate utilizing a water electrolysis cell having an acid-producing anode and a hydroxyl-producing cathode immersed in a water solution of sufficient ionic content to allow an electric current to pass between the hydroxyl-producing cathode and the acid-producing anode. A metal carbonate, in particular water-insoluble calcium carbonate or magnesium carbonate, is placed in close proximity to the acid-producing anode. A direct current electrical voltage is provided across the acid-producing anode and the hydroxyl-producing cathode sufficient to generate acid at the acid-producing anode and hydroxyl ions at the hydroxyl-producing cathode. The acid dissolves at least part of the metal carbonate into metal and carbonate ions allowing the metal ions to travel toward the hydroxyl-producing cathode and to combine with the hydroxyl ions to form the metal hydroxide. The carbonate ions travel toward the acid-producing anode and form carbonic acid and/or water and carbon dioxide. Among other uses, the metal hydroxide formed can be employed to absorb acid gases such as carbon dioxide from a gas mixture. The invention can also generate hydrogen and oxidative gases such as oxygen or chlorine.

  14. Laboratory evaluation of limestone and lime neutralization of acidic uranium mill tailings solution. Progress report

    SciTech Connect

    Opitz, B.E.; Dodson, M.E.; Serne, R.J.

    1984-02-01

    Experiments were conducted to evaluate a two-step neutralization scheme for treatment of acidic uranium mill tailings solutions. Tailings solutions from the Lucky Mc Mill and Exxon Highland Mill, both in Wyoming, were neutralized with limestone, CaCO/sub 3/, to an intermediate pH of 4.0 or 5.0, followed by lime, Ca(OH)/sub 2/, neutralization to pH 7.3. The combination limestone/lime treatment methods, CaCO/sub 3/ neutralization to pH 4 followed by neutralization with Ca(OH)/sub 2/ to pH 7.3 resulted in the highest quality effluent solution with respect to EPA's water quality guidelines. The combination method is the most cost-effective treatment procedure tested in our studies. Neutralization experiments to evaluate the optimum solution pH for contaminant removal were performed on the same two tailings solutions using only lime Ca(OH)/sub 2/ as the neutralizing agent. The data indicate solution neutralization above pH 7.3 does not significantly increase removal of pH dependent contaminants from solution. Column leaching experiments were performed on the neutralized sludge material (the precipitated solid material which forms as the acidic tailings solutions are neutralized to pH 4 or above). The sludges were contacted with laboratory prepared synthetic ground water until several effluent pore volumes were collected. Effluent solutions were analyzed for macro ions, trace metals and radionuclides in an effort to evaluate the long term effectiveness of attenuating contaminants in sludges formed during solution neutralization. Neutralized sludge leaching experiments indicate that Ca, Na, Mg, Se, Cl, and SO/sub 4/ are the only constituents which show solution concentrations significantly higher than the synthetic ground water in the early pore volumes of long-term leaching studies.

  15. Reactive solute transport in an acidic stream: Experimental pH increase and simulation of controls on pH, aluminum, and iron

    USGS Publications Warehouse

    Broshears, R.E.; Runkel, R.L.; Kimball, B.A.; McKnight, Diane M.; Bencala, K.E.

    1996-01-01

    Solute transport simulations quantitatively constrained hydrologic and geochemical hypotheses about field observations of a pH modification in an acid mine drainage stream. Carbonate chemistry, the formation of solid phases, and buffering interactions with the stream bed were important factors in explaining the behavior of pH, aluminum, and iron. The precipitation of microcrystalline gibbsite accounted for the behavior of aluminum; precipitation of Fe(OH)3 explained the general pattern of iron solubility. The dynamic experiment revealed limitations on assumptions that reactions were controlled only by equilibrium chemistry. Temporal variation in relative rates of photoreduction and oxidation influenced iron behavior. Kinetic limitations on ferrous iron oxidation and hydrous oxide precipitation and the effects of these limitations on field filtration were evident. Kinetic restraints also characterized interaction between the water column and the stream bed, including sorption and desorption of protons from iron oxides at the sediment-water interface and post-injection dissolution of the precipitated aluminum solid phase.

  16. Length Scale Dependence of the Dynamic Properties of Hyaluronic Acid Solutions in the Presence of Salt

    SciTech Connect

    Horkay, Ferenc; Falus, Peter; Hecht, Anne-Marie; Geissler, Erik

    2010-12-07

    In solutions of the charged semirigid biopolymer hyaluronic acid in salt-free conditions, the diffusion coefficient D{sub NSE} measured at high transfer momentum q by neutron spin echo is more than an order of magnitude smaller than that determined by dynamic light scattering, D{sub DLS}. This behavior contrasts with neutral polymer solutions. With increasing salt content, D{sub DLS} approaches D{sub NSE}, which is independent of ionic strength. Contrary to theoretical expectation, the ion-polymer coupling, which dominates the low q dynamics of polyelectrolyte solutions, already breaks down at distance scales greater than the Debye-Hueckel length.

  17. REDUCTION OF PLUTONIUM VALUES IN AN ACIDIC AQUEOUS SOLUTION WITH FORMALDEHYDE

    DOEpatents

    Olson, C.M.

    1959-06-01

    A method is given for reducing Pu to the tetravalent state and lowering the high acidity of dissolver solutions containing U and Pu. Formaldehyde is added to the HNO/sub 3/ solution of U and Pu to effect a formaldehyde to HNO/sub 3/ molar ratio of 0.375:1 to 1.5:1. The Pu can then be removed from the solution by carrier precipitation using BiPO/sub 4/ or by ion exchange. (T.R.H.)

  18. [Catalytic ozonation by ceramic honeycomb for the degradation of oxalic acid in aqueous solution].

    PubMed

    Zhao, Lei; Sun, Zhi-Zhong; Ma, Jun

    2007-11-01

    Comparative experiments for the degradation of oxalic acid in aqueous solution were carried out in the three processes of ozonation alone, ceramic honeycomb-catalyzed ozonation and ceramic honeycomb adsorption. The results show that the degradation rates of oxalic acid in the ceramic honeycomb-catalyzed ozonation, ozonation alone and ceramic honeycomb adsorption systems are 37.6%, 2.2% and 0.4%, and the presence of ceramic honeycomb catalyst significantly improves the degradation rate of oxalic acid compared to the results from non-catalytic ozonation and adsorption. With the addition of tert-butanol, the degradation rates of oxalic acid in catalytic ozonation system decrease by 24.1%, 29.0% and 30.1%, respectively, at the concentration of 5, 10 and 15 mg x L(-1). This phenomenon indicates that ceramic honeycomb-catalyzed ozonation for the degradation of oxalic acid in aqueous solution follows the mechanism of *OH oxidation, namely the heterogeneous surface of catalyst enhances the initiation of *OH. The results of TOC analysis demonstrate that the process of ceramic honeycomb-catalyzed ozonation can achieve the complete mineralization level without the formation of intermediary degradation products. The experimental results suggest that the reaction temperature has positive relationship with the degradation rate of oxalic acid. The degradation rates of oxalic acid in the ceramic honeycomb-catalyzed ozonation system are 16.4%, 37.6%, 61.3% and 68.2%, at the respective reaction temperature of 10, 20, 30 and 40 degrees C.

  19. Experimental Shock Chemistry of Aqueous Amino Acid Solutions and the Cometary Delivery of Prebiotic Compounds

    NASA Astrophysics Data System (ADS)

    Blank, Jennifer G.; Miller, Gregory H.; Ahrens, Michael J.; Winans, Randall E.

    2001-02-01

    A series of shock experiments were conducted to assess the feasibility of the delivery of organic compounds to the Earth via cometary impacts. Aqueous solutions containing near-saturation levels of amino acids (lysine, norvaline, aminobutyric acid, proline, and phenylalanine) were sealed inside stainless steel capsules and shocked by ballistic impact with a steel projectile plate accelerated along a 12-m-long gun barrel to velocities of 0.5-1.9 km sec^-1. Pressure-temperature-time histories of the shocked fluids were calculated using 1D hydrodynamical simulations. Maximum conditions experienced by the solutions lasted 0.85-2.7 μs and ranged from 5.1-21 GPa and 412-870 K. Recovered sample capsules were milled open and liquid was extracted. Samples were analyzed using high performance liquid chromatography (HPLC) and mass spectrometry (MS). In all experiments, a large fraction of the amino acids survived. We observed differences in kinetic behavior and the degree of survivability among the amino acids. Aminobutyric acid appeared to be the least reactive, and phenylalanine appeared to be the most reactive of the amino acids. The impact process resulted in the formation of peptide bonds; new compounds included amino acid dimers and cyclic diketopiperazines. In our experiments, and in certain naturally occurring impacts, pressure has a greater influence than temperature in determining reaction pathways. Our results support the hypothesis that significant concentrations of organic material could survive a natural impact process.

  20. Experimental shock chemistry of aqueous amino acid solutions and the cometary delivery of prebiotic compounds.

    PubMed

    Blank, J G; Miller, G H; Ahrens, M J; Winans, R E

    2001-01-01

    A series of shock experiments were conducted to assess the feasibility of the delivery of organic compounds to the Earth via cometary impacts. Aqueous solutions containing near-saturation levels of amino acids (lysine, norvaline, aminobutyric acid, proline, and phenylalanine) were sealed inside stainless steel capsules and shocked by ballistic impact with a steel projectile plate accelerated along a 12-m-long gun barrel to velocities of 0.5-1.9 km sec-1. Pressure-temperature-time histories of the shocked fluids were calculated using 1D hydrodynamical simulations. Maximum conditions experienced by the solutions lasted 0.85-2.7 microseconds and ranged from 5.1-21 GPa and 412-870 K. Recovered sample capsules were milled open and liquid was extracted. Samples were analyzed using high performance liquid chromatography (HPLC) and mass spectrometry (MS). In all experiments, a large fraction of the amino acids survived. We observed differences in kinetic behavior and the degree of survivability among the amino acids. Aminobutyric acid appeared to be the least reactive, and phenylalanine appeared to be the most reactive of the amino acids. The impact process resulted in the formation of peptide bonds; new compounds included amino acid dimers and cyclic diketopiperazines. In our experiments, and in certain naturally occurring impacts, pressure has a greater influence than temperature in determining reaction pathways. Our results support the hypothesis that significant concentrations of organic material could survive a natural impact process. PMID:11296518

  1. Improved process for the production of cellulose sulfate using sulfuric acid/ethanol solution.

    PubMed

    Chen, Guo; Zhang, Bin; Zhao, Jun; Chen, Hongwen

    2013-06-01

    An improved process for production of cellulose sulfate (CS) was developed by using sulfuric acid/ethanol solution as sulfonating agent and Na2SO4 as water absorbent. The FTIR, SEM and TG analysis were used to characterize the CS prepared. The total degree of substitution and viscosity of the product solution (2%, w/v) were ranging from 0.28 to 0.77 and from 115 to 907 mPa s, respectively, by changing the process parameters such as the amount of Na2SO4, the reaction time, the temperature, the sulfuric acid/alcohol ratio and liquid/solid ratio. The results indicated that the product with DS (0.28-0.77) and η2% (115-907) mPa s could be produced by using this improved process and more cellulose sulfate could be produced when cellulose was sulfonated for 3-4 h at -2 °C in sulfuric acid/ethanol (1.4-1.6) solution with addition of 0.8 g Na2SO4. The (13)C NMR indicated that the sulfate group of CS produced using sulfuric acid/ethanol solution was at C6 position.

  2. Effect of acid solutions on plants studied by the optical beam deflection method.

    PubMed

    Nie, Liangjiao; Kuboda, Mitsutoshi; Inoue, Tomomi; Wu, Xingzheng

    2013-12-01

    The optical beam deflection method was applied to study the effects of acid solution on both a terrestial and aquatic plants Egeria and Cerastium, which are common aquatic plant and terrestial weed respectively. A probe beam from a He-Ne laser was passed through a vicinity of a leaf of the plants, which were put in culture dishes filled with acid solutions. Deflection signals of the probe beam were monitored and compared for acid solutions with different pH values. The results of Egria showed that the deflection signals changed dramatically when pH values of acid solutions were 2.0 and 3.0, while little at pH of 4.0 and 5.0. For Cerastium when pH were below 3.0, deflection signals changed greatly with time at the begining. After a certain period of time, deflection signals changed little with time. When pH value was above 4.0, deflection signals of Cerastium were still changing with time even after 20 hours. The results suggested that the damage threshold of pH was between 3.0 and 4.0 for both the land and aquatic plants.

  3. Solution blow spun Poly(lactic acid)/Hydroxypropyl methylcellulose nanofibers with antimicrobial properties

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Poly(lactic acid) (PLA) nanofibers containing hydroxypropyl methylcellulose (HPMC) and tetracycline hydrochloride (THC) were solution blow spun from two different solvents, chloroform/acetone (CA, 80:20 v/v) and 2,2,2-triflouroethanol (TFE). The diameter distribution, chemical, thermal, thermal stab...

  4. PHYSICAL SOLUTIONS FOR ACID ROCK DRAINAGE AT REMOTE SITES DEMONSTRATION PROJECT

    EPA Science Inventory

    This report summarizes the results of Mine Waste Technology Program, Activity III, Project 42, Physical Solutions for Acid Rock Drainage at Remote Sites, funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by EPA and the U.S. Department of Energy. A...

  5. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  6. Cesium absorption from acidic solutions using ammonium molybdophosphate on a polyacrylonitrile support (AMP-PAN)

    SciTech Connect

    Miller, C.J.; Olson, A.L.; Johnson, C.K.

    1995-12-01

    Recent efforts at the Idaho Chemical Processing Plant (ICPP) have included evaluation of cesium removal technologies as applied to ICPP acidic radioactive waste streams. Ammonium molybdophosphate (AMP) immobilized on a polyacrylonitrile support (AMP-PAN) has been studied as an ion exchange agent for cesium removal from acidic waste solutions. Capacities, distribution coefficients, elutability, and kinetics of cesium-extraction have been evaluated. Exchange breakthrough curves using small columns have been determined from 1M HNO{sub 3} and simulated waste solutions. The theoretical capacity of AMP is 213 g Cs/kg AMP. The average experimental capacity in batch contacts with various acidic solutions was 150 g Cs/kg AMP. The measured cesium distribution coefficients from actual waste solutions were 3287 mL/g for dissolved zirconia calcines, and 2679 mL/g for sodium-bearing waste. The cesium in the dissolved alumina calcines was analyzed for; however, the concentration was below analytical detectable limits resulting in inconclusive results. The reaction kinetics are very rapid (2-10 minutes). Cesium absorption appears to be independent of acid concentration over the range tested (0.1 M to 5 M HNO{sub 3}).

  7. [Effects of UV Radiation on the Physicochemical Properties and Coagulation Properties of Humic Acid Solution].

    PubMed

    Wang, Wen-dong; Zhang, Ke; Fan, Qing-hai; Zheng, Dan

    2016-03-15

    To investigate the mechanism of UV light in promoting the removal of humic acid ( HA) by coagulation, the variations of the physical and chemical properties of the HA solution before and after UV light radiation were investigated. The effects of the changes in water quality conditions on the removal performance of HA in coagulation were also observed. Experimental results showed that except zeta potential, pH, chromaticity and viscosity of the HA solution exhibited varying degrees of decline after UV radiation. Further study showed that the impact of changes in viscosity of the solution on humic acid coagulation performance was relatively small. Under acidic conditions, the coagulation performance of HA significantly increased. The increase of zeta potential led to easy gathering of colloidal particles and improved the coagulation performance. Furthermore, except for HA with relative molecular mass of between (10-30) x 10³ and less than 10³, there was little variation in the proportion of low molecular weight HA, which may be an important reason that the coagulation performance of the humic acid solution increased after UV radiation. PMID:27337892

  8. Modification of vital wheat gluten with phosphoric acid to produce high free-solution capacity

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Wheat gluten reacts with phosphoric acid to produce natural superabsorbent gels. The gel properties are defined by Fourier Transform Infra-red (FTIR) spectroscopy, 2-dimensional gel electrophoresis (2DE), and uptake of water, salt solutions, and aqueous ethanol. Temperatures above 120'C and dry cond...

  9. Effect of acid solutions on plants studied by the optical beam deflection method.

    PubMed

    Nie, Liangjiao; Kuboda, Mitsutoshi; Inoue, Tomomi; Wu, Xingzheng

    2013-12-01

    The optical beam deflection method was applied to study the effects of acid solution on both a terrestial and aquatic plants Egeria and Cerastium, which are common aquatic plant and terrestial weed respectively. A probe beam from a He-Ne laser was passed through a vicinity of a leaf of the plants, which were put in culture dishes filled with acid solutions. Deflection signals of the probe beam were monitored and compared for acid solutions with different pH values. The results of Egria showed that the deflection signals changed dramatically when pH values of acid solutions were 2.0 and 3.0, while little at pH of 4.0 and 5.0. For Cerastium when pH were below 3.0, deflection signals changed greatly with time at the begining. After a certain period of time, deflection signals changed little with time. When pH value was above 4.0, deflection signals of Cerastium were still changing with time even after 20 hours. The results suggested that the damage threshold of pH was between 3.0 and 4.0 for both the land and aquatic plants. PMID:25078849

  10. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  11. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  12. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  13. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  14. Extractant-coated magnetic particles for cobalt and nickel recovery from acidic solution.

    SciTech Connect

    Kaminski, M. D.; Nunez, L.; Chemical Engineering

    1999-04-01

    Waste minimization and recycling practices can often constitute a significant fraction of industrial operating costs. Magnetically assisted chemical separation (MACS) is a simple, cost-effective process that utilizes micrometer-sized magnetic composite materials containing a sorbed layer of chelating or ion exchange material. This paper presents the use of MACS particles for recovering cobalt and nickel from acidic solution.

  15. IMPROVEMENT UPON THE CARRIER PRECIPITATION OF PLUTONIUM IONS FROM NITRIC ACID SOLUTIONS

    DOEpatents

    James, R.A.; Thompson, S.G.

    1958-12-23

    A process is reported for improving the removal of plutonlum by carrier precipitation by the addition of nitrite ions to a nitrlc acid solutlon of neutronirradiated unanium so as to destroy any hydrazine that may be present in the solution since the hydrazine tends to complex the tetravalent plutonium and prevents removal by the carrier precipltate, such as bismuth phospbate.

  16. Spray washing carcasses with alkaline solutions of lauric acid to reduce bacterial contamination

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The ability of lauric acid (LA)-potassium hydroxide (KOH) solutions to reduce carcass bacterial contamination was examined. Skin of carcasses was inoculated with a cecal paste containing antibiotic resistant strains of Escherichia coli, Salmonella Typhimirum, and Campylobacter coli. In one trial, in...

  17. Extractant-coated magnetic particles for cobalt and nickel recovery from acidic solution

    NASA Astrophysics Data System (ADS)

    Kaminski, M. D.; Nuñez, L.

    1999-04-01

    Waste minimization and recycling practices can often constitute a significant fraction of industrial operating costs. Magnetically assisted chemical separation (MACS) is a simple, cost-effective process that utilizes micrometer-sized magnetic composite materials containing a sorbed layer of chelating or ion exchange material. This paper presents the use of MACS particles for recovering cobalt and nickel from acidic solution.

  18. A unified molecular picture of the surfaces of aqueous acid, base, and salt solutions

    SciTech Connect

    Mucha, M.; Frigato, Tomaso; Levering, Lori; Allen, Heather C.; Tobias, Douglas J.; Dang, Liem X.; Jungwirth, Pavel

    2005-04-28

    A unified view of the structure of the air/solution interface of simple aqueous electrolytes containing monovalent inorganic ions is developed using molecular dynamics simulations and vibrational sum frequency generation spectroscopy. In salt solutions and bases the positively charged ions, such as alkali cations, are repelled from the air/solution interface, while the anions, such as halides or hydroxide, exhibit a varying propensity for the surface, correlated primarily with the polarizability of the ion. As a result, there is a net depletion of ions from the interfacial layer as a whole, which is connected via the Gibbs adsorption equation to an increase in surface tension with respect to neat water. The behavior of acids, such as aqueous HCl or HBr, is different due to a significant propensity of hydronium cations for the air/solution interface. Therefore, both cations and anions exhibit enhanced concentrations at the surface and, consequently, these acids reduce the surface tension of water. The key to the qualitatively different surface behavior of aqueous salt solutions and bases on one side and acids on the other thus lies in the appreciable adsorption of hydronium cations at the air/solution interface with their “hydrophobic” oxygen side oriented towards the gas phase. The results of the molecular dynamics calculations are supported by surface selective non-linear vibrational spectroscopy, which reveals among other things that the hydronium cations are present at the air/solution interface. The propensity of inorganic ions for the air/solution interface has important implications for heterogeneous chemical processes, in particular for atmospheric chemistry.

  19. Thermal stability of 5-o-caffeoylquinic acid in aqueous solutions at different heating conditions.

    PubMed

    Dawidowicz, Andrzej L; Typek, Rafal

    2010-12-22

    Chlorogenic acid is a naturally occurring phenolic compound found in all higher plants. This component, being the ester of caffeic acid with quinic acid, is an important biosynthetic intermediate and plays an important role in the plant's response to stress. Potential uses of chlorogenic acid are suggested in pharmaceuticals, foodstuffs, feed additives, and cosmetics due to its recently discovered biomedical activity. This finding caused new interest in chlorogenic acid properties, its isomers, and its natural occurrence. It has been found that as many as nine compounds (chlorogenic acid derivatives and its reaction product with water) can be formed from 5-o-caffeoylquinic acid during the heating of its water solution. Three of them, two hydroxylated 5-o-caffeoylquinic acid derivatives and 4,5-dicaffeoylquinic acid, have been not reported, yet. The amount of each formed component depends on the heating time and temperature. The presented results are important for researchers investigating plant metabolism and looking for new plant components. The transformation product can be mistakenly treated as a new component, not found before in the examined plant, or can be a cause of erroneous quantitative estimations of plant composition.

  20. Citric Acid-Modified Fenton's Reaction for the Oxidation of Chlorinated Ethylenes in Soil Solution Systems

    SciTech Connect

    Seol, Yongkoo; Javandel, Iraj

    2008-03-15

    Fenton's reagent, a solution of hydrogen peroxide and ferrous iron catalyst, is used for an in-situ chemical oxidation of organic contaminants. Sulfuric acid is commonly used to create an acidic condition needed for catalytic oxidation. Fenton's reaction often involves pressure buildup and precipitation of reaction products, which can cause safety hazards and diminish efficiency. We selected citric acid, a food-grade substance, as an acidifying agent to evaluate its efficiencies for organic contaminant removal in Fenton's reaction, and examined the impacts of using citric acid on the unwanted reaction products. A series of batch and column experiments were performed with varying H{sub 2}O{sub 2} concentrations to decompose selected chlorinated ethylenes. Either dissolved iron from soil or iron sulfate salt was added to provide the iron catalyst in the batch tests. Batch experiments revealed that both citric and sulfuric acid systems achieved over 90% contaminant removal rates, and the presence of iron catalyst was essential for effective decontamination. Batch tests with citric acid showed no signs of pressure accumulation and solid precipitations, however the results suggested that an excessive usage of H{sub 2}O{sub 2} relative to iron catalysts (Fe{sup 2+}/H{sub 2}O{sub 2} < 1/330) would result in lowering the efficiency of contaminant removal by iron chelations in the citric acid system. Column tests confirmed that citric acid could provide suitable acidic conditions to achieve higher than 55% contaminant removal rates.

  1. Electrochemical formation of hydroxide for enhancing carbon dioxide and acid gas uptake by a solution

    DOEpatents

    Rau, Gregory Hudson

    2014-07-01

    A system for forming metal hydroxide from a metal carbonate utilizes a water electrolysis cell having an acid-producing anode and a hydroxyl-producing cathode immersed in a water solution of sufficient ionic content to allow an electric current to pass between the hydroxyl-producing cathode and the acid-producing anode. A metal carbonate is placed in close proximity to the acid-producing anode. A direct current electrical voltage is provided across the acid-producing anode and the hydroxyl-producing cathode sufficient to generate acid at the acid-producing anode and hydroxyl ions at the hydroxyl-producing cathode. The acid dissolves at least part of the metal carbonate into metal and carbonate ions allowing the metal ions to travel toward the hydroxyl-producing cathode and to combine with the hydroxyl ions to form the metal hydroxide. The carbonate ions travel toward the acid-producing anode and form carbonic acid and/or water and carbon dioxide.

  2. Acid stability of anti-Helicobacter pyroli IgY in aqueous polyol solution.

    PubMed

    Lee, Kyong Ae; Chang, Sung Keun; Lee, Yoon Jin; Lee, Jong Hwa; Koo, Nan Sook

    2002-09-30

    IgY was separated from a hen's egg yolk that was immunized with Helicobacter pyroli. The anti-H. pyroli IgY activity at acidic pH and the suppressive effect of polyol on acid-induced inactivation of IgY were investigated. Sorbitol and xylitol were used as polyols. IgY was quite stable at pH 5-7. Irreversible inactivation of IgY was observed at pH below 4, and proceeded rapidly at pH below 3. The acid stability of IgY was enhanced in the presence of 30% sorbitol or above. In a 50% aqueous sorbitol solution, an acid-induced inactivation was almost completely suppressed at pH 3. However, the improvement of IgY activity was not observed in the aqueous xylitol solution. IgY showed almost the same activity as native IgY when sucrose was substituted for sorbitol. On the other hand, the xylitol replacement with sucrose did not enhance the acid stability of IgY. The acid-induced inactivation of IgY was related to tryptophyl fluorescence. Fluorescence emission spectra suggested that structural changes near the tryptophan residues may occur under acidic conditions. An increase in sorbitol concentration induced a blue shift. The fluorescence emission of IgY in a 50% sorbitol solution had a peak at 330 nm, which was the same emission peak that was exhibited by native IgY. Sorbitol could, therefore, be used as a good stabilizer of IgY under acidic conditions. PMID:12359091

  3. Influence of uranium on corrosion of stainless steel in solutions of fluoride in nitric acid

    SciTech Connect

    Kurtenov, M.M.

    1985-09-01

    Stainless steels corrode rapidly in solutions of fluoride in nitric acid; the higher the fluoride ion content, the more intense is the corrosion. The activating effect of the fluoride ions mainly reduces to dissolution of the oxide films. Small amounts somewhat retard the cathodic reduction of HNO/sub 3/. In this report the authors provide the results of an investigation of the influence of uranium ions on the corrosion-electrochemical behavior of stainless steel 12Kh18N10T in solutions of up to 10 moles/liter of HNO/sub 3/, with fluoride ions up to 0.1 mole/liter. The authors conclude that the retardation of corrosion of stainless steel by uranium, zirconium and aluminum ions in solutions of fluorides in nitric acid is mainly due to the formation of strong complexes of these metals with fluorine ions, leading to a reduction of the number of free HF molecules in the solution. The stronger the complex of metal with fluorine, the higher the corrosion resistance of the stainless steel in a solution of fluoride in nitric acid.

  4. Effect of tannic acid solution on collagen structures for dental restoration.

    PubMed

    Natsir, N; Wakasa, K; Yoshida, Y; Satou, N; Shintani, H

    1999-08-01

    This study examined the effect of tannic acid solution on dissolution of dentine collagen and morphological aspects of tendon collagen. Using root dentine, which was cut off from bovine anterior tooth, dentine powders were obtained by the pulverization and lyophilization. They were subject to an application of 1, 3, 5 or 10% tannic acid (TA) solution for 1, 3, 6, 12 or 24 h. TA-treated dentine powders were treated with 40% phosphoric acid (PA) for 30 s at 20 degrees C and additionally with trypsin. Released hydroxyproline in Woessner's assay after a hydrolysis in 6 N HCl at 110 degrees C for 20 h was assumed to be dissolved dentine collagen. Released hydroxyproline in a control sample without acid treatment decreased from 100 to about 60% with increased TA concentration of 1 to 10%, and decreased with increased incubation times of 1 to 24 h when applied by 5% TA solution. Scanning electron microscopy results established the morphological effect of their surface characteristics due to such treatments as 40% PA for 30 s and 5% TA for 6 h, or 40% PA after 5% TA treatment, yielding collagen structures protected by TA to attack from phosphoric acid.

  5. Calculated and measured [Ca(2+)] in buffers used to calibrate Ca(2+) macroelectrodes.

    PubMed

    McGuigan, John A S; Stumpff, Friederike

    2013-05-01

    The ionized concentration of calcium in physiological buffers ([Ca(2+)]) is normally calculated using either tabulated constants or software programs. To investigate the accuracy of such calculations, the [Ca(2+)] in EGTA [ethylene glycol-bis(β-aminoethylether)-N,N,N|,N|-tetraacetic acid], BAPTA [1,2-bis(o-aminophenoxy) ethane-N,N,N|,N|-tetraacetic acid], HEDTA [N-(2-hydroxyethyl)-ethylenediamine-N,N|,N|-triacetic acid], and NTA [N,N-bis(carboxymethyl)glycine] buffers was estimated using the ligand optimization method, and these measured values were compared with calculated values. All measurements overlapped in the pCa range of 3.51 (NTA) to 8.12 (EGTA). In all four buffer solutions, there was no correlation between measured and calculated values; the calculated values differed among themselves by factors varying from 1.3 (NTA) to 6.9 (EGTA). Independent measurements of EGTA purity and the apparent dissociation constants for HEDTA and NTA were not significantly different from the values estimated by the ligand optimization method, further substantiating the method. Using two calibration solutions of pCa 2.0 and 3.01 and seven buffers in the pCa range of 4.0-7.5, calibration of a Ca(2+) electrode over the pCa range of 2.0-7.5 became a routine procedure. It is proposed that such Ca(2+) calibration/buffer solutions be internationally defined and made commercially available to allow the precise measurement of [Ca(2+)] in biology.

  6. Mixed field radiation effects on dry and acidic solution saturated polyamide 6,6

    NASA Astrophysics Data System (ADS)

    Brown, L.; Bonin, H. W.; Bui, V. T.

    2005-05-01

    The disposal of Canada's radioactive waste materials has been the focus of ongoing research at the Royal Military College of Canada, in the use of polymer-based composite materials for the fabrication of disposal containers. An evaluation of the performance of polyamide 6,6 after exposure to radiation and acidic aqueous solutions provides the basis for the assessment of the lifetime performance of a polymeric-based storage container. This work demonstrates the importance of the combined effects of aqueous solution diffusion and radiation exposure on the mechanical performance and molecular structure of polyamide 6,6. Irradiation of dry samples initially results in a marked reduction of mechanical performance, however, post-irradiation aging allows for the return to pre-irradiation mechanical strength. Samples irradiated after exposure to either distilled water or 0.1 M sulfuric acid solutions exhibited increases in mechanical performance upon exposure to a mixed field radioactive environment.

  7. Influence of biuret and cyanuric acid on dewaxing petroleum stocks with alcoholic urea solution

    SciTech Connect

    Abdullaev, E.Sh.; Ismailov, A.G.; Gadzhiev, A.Sh.; Balayan, R.D.

    1987-11-01

    The influence of biuret and cyanuric acid contents on the formation and separation of the adduct in commercial dewaxing of petroleum stocks by a urea solution in a water and isopropyl alcohol mixture was studied. The stock was a diesel fuel distillate with a solid point of -12/sup 0/C. Experiments were performed with a 3.5:1 volume ratio of urea solution to feed, urea content 38% by weight, isopropyl alcohol concentration 70% by weight, adduct formation temperature 55-30/sup 0/C, and adduct formation duration 30 min. Test results show the adverse effects at different quantities of cyanuric and biuret acids on adduct formation. Solutions for overcoming these effects are proposed.

  8. Role of Organic Solutes in the Chemistry Of Acid-Impacted Bog Waters of the Western Czech Republic

    NASA Astrophysics Data System (ADS)

    HrušKa, Jakub; Johnson, Chris E.; KráM, Pavel

    1996-04-01

    In many regions, naturally occurring organic acid anions can effectively buffer mineral acid inputs from atmospheric deposition, moderating their effect on surface water pH. We studied the effect of chronically high inputs of acid rain on the chemistry of three brown-water streams in the western Czech Republic. The dissolved organic acids in the streams were similar in character to those of other systems in Europe and North America. The site densities (the carboxyl group content per mass of C) were similar to values reported from Fenno-Scandia, and the relationship between the apparent pKa and pH conformed to those from two North American studies. Sulfate and organic acid anions (OA-) were the dominant anions in all three streams, yet despite high dissolved organic carbon and total organic acid concentrations, OA - comprised only 21-32% of total anion charge. This pattern was due to very high sulfate concentrations and, in two of the streams, a low degree of dissociation of the organic acids, probably the results of high long-term inputs of strong acids. Stream water pH was highly correlated to sulfate concentration, but uncorrelated with OA-, suggesting that free acidity is controlled by strong mineral acids rather than organic acids. Thus future reductions in strong acid inputs should result in increased pH and a return to organic control over acid-base chemistry.

  9. Open-label evaluation of a novel skin brightening system containing 0.01% decapeptide-12 in combination with 20% buffered glycolic acid for the treatment of mild to moderate facial melasma.

    PubMed

    Ramírez, Sandra P; Carvajal, Alfonso C; Salazar, Juan C; Arroyave, Gladys; Flórez, Ana M; Echeverry, Hector F

    2013-06-01

    Melasma is a cutaneous disorder that primarily affects females of Hispanic and Asian descent. Previous studies have shown that use of a brightening system comprised of 0.01% decapeptide-12 cream, an antioxidant cleanser, a 20% buffered glycolic acid lotion, and a broad spectrum SPF 30 sunscreen yields good clearance of mild-to-moderate melasma in Caucasian and Asian volunteers. The present open-label, prospective, and multicenter study sought to determine the tolerability and efficacy of the above-mentioned brightening system on mild-to-moderate melasma in 33 Hispanic females over 16 weeks. Clinical measures included self-assessment of tolerability, clinical grading, determination of Melasma Area and Severity Index (MASI) scores, and standardized clinical photography. Results showed that the system was well tolerated with no adverse events reported. Mean decreases of 36%, 46%, 54%, and 60% in MASI scores were observed at weeks 4, 8, 12, and 16, respectively, which were further corroborated by standardized photography showing visible reduction in the appearance of melasma. Results suggest that the brightening system consisting of 0.01% decapeptide-12 cream, an antioxidant cleanser, 20% buffered glycolic acid lotion, and broad spectrum SPF 30 sunscreen is safe and efficacious for the treatment of mild-to-moderate melasma in Hispanic females.

  10. Study of the decomposition pathway of 12-molybdophosphoric acid in aqueous solutions by micro Raman spectroscopy.

    PubMed

    Bajuk-Bogdanović, D; Uskoković-Marković, S; Hercigonja, R; Popa, A; Holclajtner-Antunović, I

    2016-01-15

    Micro Raman spectroscopy was applied to investigate the speciation of heteropoly and isopoly molybdates in 0.05 and 0.005 M aqueous solutions of 12-molybdophosphoric acid at pH values between 1 and 6. For comparative purposes, (31)P NMR spectroscopy was applied too. It is shown that stability of Keggin anion is influenced both by pH and concentration of solution. The Keggin structure is stable in acidic solutions (pH<1.6) while defective Keggin structures are formed with further alkalization (up to pH5.6). Monolacunary anion PMo11O(39)(7-) is the main component in the pH region from 1.6 to 3.4. Further removal of molybdenyl species causes the appearance of other vacant Keggin structures such as PMo9O31(OH)(3)(6-) and PMo6O(25)(9-) at about pH4. At pH5.0, anion PMo6O(25)(9-) is the main species. In solutions with pH greater than 5.0, heteropolymolybdates disappear completely and isopolymolybdates Mo7O(24)(6-) and MoO(4)(2-) are formed in higher amounts. In more diluted solution of 0.005 M, the decomposition scheme of 12-molybdophosphoric acid solution with increasing of pH takes place without observation of significant amounts of Mo7O(24)(6-) species. If alkalinization is performed with 0.5 M instead of 5 M NaOH, there are no significant changes in the Raman spectra of solutions. It is shown that the spectra of evaporated samples may be used for the identification of molecular species in corresponding concentrated solutions. However, Raman spectra of dry residues of more diluted solutions differ from spectra of corresponding solutions due to the reactions performed during the process of drying and cannot be used for unambiguous identification of species in solution. Acidification of 0.05 M solution of Na2MoO4 shows that at pH>5.6, molybdate anion MoO(4)(2-) dominates, while in the pH range between 5.6 and 1, heptamolybdate anion Mo7O(24)(6-) is preferentially formed.

  11. Macroreticulate buffers: a novel approach to pH control in living systems.

    PubMed

    Righetti, P G; Chiari, M; Crippa, L

    1991-02-01

    It is possible to control the pH of growing living systems in vitro by adding, to the growth media, macroreticulate buffers, i.e. amphoteric resins made with buffering and titrant groups simultaneously affixed to the matrix. Such beads possess a very precise isoelectric point (pI) and are able to maintain the solutions' pH close to their pI values for extended growth periods. These pearls are made of a neutral polyacrylamide backbone containing up to 200 mM grafted weak acrylamido acids and bases. It is possible to produce such buffers with any desired pH value in the pH 2.5-11 scale. An example is given of conditioning the pH of endive plants grown hydroponically. PMID:1366985

  12. Adsorptions of some heavy metal ions in aqueous solutions by acrylamide/maleic acid hydrogels

    SciTech Connect

    Saraydin, D.; Karadag, E.; Gueven, O.

    1995-10-01

    In this study, acrylamide-maleic acid (AAm/MA) hydrogels in the form of rod have been prepared by {gamma}-radiation. They have been used for adsorption of some heavy metal ions such as uranium, iron, and copper. For the hydrogel containing 40 mg of maleic acid and irradiated at 3.73 kGy, maximum and minimum swellings in the aqueous solutions of the heavy metal ions have been observed with water (1480%) and the aqueous solution of iron(III) nitrate (410%), respectively. Diffusions of water and heavy metal ions onto hydrogels have been found to be of the non-Fickian type of diffusion. In experiments of uranyl ions adsorption, Type II adsorption has been found. One gram of AAa/MA hydrogels sorbed 14-86 mg uranyl ions from solutions of uranyl acetate, 14-90 mg uranyl ions from solutions of uranyl nitrate, 16-39 mg iron ions from solutions of iron(IV) nitrate, and 28-81 mg copper ions from solutions of copper acetate, while acrylamide hydrogel did not sorb any heavy metals ions.

  13. Effective Removal of Tetracycline from Aqueous Solution by Organic Acid-Coated Magnetic Nanoparticles.

    PubMed

    Guo, Liang; Liang, Yuyan; Chen, Xuelan; Xu, Wei; Wu, Kesheng; Wei, Hua; Xiong, Yonghua

    2016-03-01

    Self-assembled iron oxide nanocomposites are good magnetic nano-adsorbents that can be prepared using simple methods. Four types of organic acid-functionalised (oleic acid, undecenoic acid, caprylic acid or hexanoic acid) magnetic nanoparticles (MNPs) were synthesised through a one-pot chemisorption method for the removal of tetracycline (TC) from aqueous solution. The undecenoic acid-coated MNPs (UA-MNPs) exhibited the highest adsorption efficiency and can be easily retrieved with a low-gradient magnetic separator (0.4 Tesla) at pH 5.0 aqueous solution. The TC adsorption process on the UA-MNPs followed the Langmuir isotherm and the maximum adsorption capacities increased from 86.96 mg g(-1) to 222.2 mg g(-1) with the increase in temperature from 288 K to 318 K. The kinetics of adsorption fits pseudo-second-order model perfectly with a rate constant, 5.946 g mg(-1) min(-1) at 298 K. The positive values of the enthalpy (AH) and the negative value of the free energy (AG) indicated an endothermic and spontaneous adsorption process of TC on the UA-MNPs. Moreover, the UA-MNPs possessed excellent ability to adsorb the other three major types of TC antibiotics, including chlortetracycline, oxytetracycline and doxycycline. PMID:27455621

  14. Stimulation of glycolysis by histidine buffers in mammalian liver during cold hypoxia.

    PubMed

    Churchill, T A; Green, C J; Fuller, B J

    1995-06-20

    This study was designed to address the reasons why glycolysis in mammalian liver is unable to function more efficiently during periods of cold hypoxia. Our hypothesis was that control of intracellular pH, by use of amino acid buffers with high pKa values, would allow prolonged flux through glycolysis and better maintenance of liver high-energy adenine nucleotide pool. The effects of two concentrations of histidine (90 and 180 mM) and one of carnosine (90 mM), a histidyl dipeptide, on energy metabolism and levels of glycolytic substrate (glucose) and anaerobic endproduct (lactate) were investigated during cold hypoxia using rat livers to model the mammalian system. The transition to anaerobic metabolism was apparent by an immediate rise in lactate levels upon entry into cold hypoxia. By 10-14 h hypoxia, contents of the endproduct had increased by 10, 13.5, and 14.5 mumol/g in buffers containing 90 and 180 mM histidine and 90 mM carnosine, respectively. As well, ATP, total adenylate contents, and "energy charge" ratios exhibited a rapid decline from initial values of 2.3-3.3 mumol/g, 4.3-5.5 mumol/g, and 0.64-0.75, respectively, over the first 2-4 h of cold hypoxia. With respect to efficacy, the 180 mM histidine buffer exhibited the most positive maintenance of adenylate levels, followed closely by 90 mM carnosine, and finally 90 mM histidine as the least effective of the three buffers. Nevertheless, all three buffers examined in this study showed positive effects compared to similarly treated livers stored in a solution of minor buffering capacity (a citrate-based solution) over the same time period. The data support the hypothesis that glycolytic flux and cellular energetics can be maintained by the inclusion of efficient buffering agents during periods of cold hypoxia.

  15. Interaction of Atmospheric-Pressure Air Microplasmas with Amino Acids as Fundamental Processes in Aqueous Solution.

    PubMed

    Zhou, Renwu; Zhou, Rusen; Zhuang, Jinxing; Zong, Zichao; Zhang, Xianhui; Liu, Dongping; Bazaka, Kateryna; Ostrikov, Kostya

    2016-01-01

    Plasma medicine is a relatively new field that investigates potential applications of cold atmospheric-pressure plasmas in bioengineering, such as for bacterial inactivation and degradation of organic molecules in water. In order to enunciate mechanisms of bacterial inactivation at molecular or atomic levels, we investigated the interaction of atmospheric-pressure air microplasmas with amino acids in aqueous solution by using high-resolution mass spectrometry (HRMS). Results show that the oxidation effect of plasma-induced species on the side chains of the amino acids can be categorized into four types, namely hydroxylation, nitration, dehydrogenation and dimerization. In addition, relative activities of amino acids resulting from plasma treatment come in descending order as follows: sulfur-containing carbon-chain amino acids > aromatic amino acids > five-membered ring amino acids > basic carbon-chain amino acids. Since amino acids are building blocks of proteins vital to the growth and reproduction of bacteria, these results provide an insight into the mechanism of bacterial inactivation by plasma. PMID:27183129

  16. Interaction of Atmospheric-Pressure Air Microplasmas with Amino Acids as Fundamental Processes in Aqueous Solution

    PubMed Central

    Zhou, Renwu; Zhou, Rusen; Zhuang, Jinxing; Zong, Zichao; Zhang, Xianhui; Liu, Dongping; Bazaka, Kateryna; Ostrikov, Kostya

    2016-01-01

    Plasma medicine is a relatively new field that investigates potential applications of cold atmospheric-pressure plasmas in bioengineering, such as for bacterial inactivation and degradation of organic molecules in water. In order to enunciate mechanisms of bacterial inactivation at molecular or atomic levels, we investigated the interaction of atmospheric-pressure air microplasmas with amino acids in aqueous solution by using high-resolution mass spectrometry (HRMS). Results show that the oxidation effect of plasma-induced species on the side chains of the amino acids can be categorized into four types, namely hydroxylation, nitration, dehydrogenation and dimerization. In addition, relative activities of amino acids resulting from plasma treatment come in descending order as follows: sulfur-containing carbon-chain amino acids > aromatic amino acids > five-membered ring amino acids > basic carbon-chain amino acids. Since amino acids are building blocks of proteins vital to the growth and reproduction of bacteria, these results provide an insight into the mechanism of bacterial inactivation by plasma. PMID:27183129

  17. Interaction of Atmospheric-Pressure Air Microplasmas with Amino Acids as Fundamental Processes in Aqueous Solution.

    PubMed

    Zhou, Renwu; Zhou, Rusen; Zhuang, Jinxing; Zong, Zichao; Zhang, Xianhui; Liu, Dongping; Bazaka, Kateryna; Ostrikov, Kostya

    2016-01-01

    Plasma medicine is a relatively new field that investigates potential applications of cold atmospheric-pressure plasmas in bioengineering, such as for bacterial inactivation and degradation of organic molecules in water. In order to enunciate mechanisms of bacterial inactivation at molecular or atomic levels, we investigated the interaction of atmospheric-pressure air microplasmas with amino acids in aqueous solution by using high-resolution mass spectrometry (HRMS). Results show that the oxidation effect of plasma-induced species on the side chains of the amino acids can be categorized into four types, namely hydroxylation, nitration, dehydrogenation and dimerization. In addition, relative activities of amino acids resulting from plasma treatment come in descending order as follows: sulfur-containing carbon-chain amino acids > aromatic amino acids > five-membered ring amino acids > basic carbon-chain amino acids. Since amino acids are building blocks of proteins vital to the growth and reproduction of bacteria, these results provide an insight into the mechanism of bacterial inactivation by plasma.

  18. Dilute nitric or nitrous acid solution containing halide ions as effective media for pure gold dissolution.

    PubMed

    Hojo, Masashi; Yamamoto, Masahiko; Okamura, Kei

    2015-08-14

    The greatly enhanced oxidation ability of dilute aqueous nitric acid (0.10-2.0 mol L(-1)) containing bromide and iodide salts as well as chloride salts has been examined based on the dissolution kinetics of pure gold at 30-60 °C. It has been found that bromide salts are more effective than chloride salts in gaining the ability of dissolving gold in dilute aqueous nitric acid solution. At 60 °C, a piece of gold-wire (ca. 20 mg) is dissolved in 20 mL of as low as 0.10 mol L(-1) HNO3 solution containing 1.0-5.0 mol L(-1) NaBr and the dissolution rate constant, log(k/s(-1)), increases linearly (from -5.78 to -4.52) with the increasing NaBr concentration. The addition of organic solvents, such as acetonitrile and acetic acid, causes acceleration of gold dissolution in LiBr and NaBr solutions. With increasing MeCN contents, for instance, the log(k/s(-1)) value of 0.10 mol L(-1) HNO3 solution containing 2.0 mol L(-1) NaBr increases linearly from -5.30 to -4.61 at 30% (v/v) MeCN. The bromide salts affect the gold dissolution rate constant in the order of KBr < NaBr < LiBr < CaBr2. With increasing NaI concentration (0.20-3.0 mol L(-1)), some acceleration in log(k/s(-1)) of 0.50 or 1.0 mol L(-1) HNO3 solution has been observed; however, the slope of acceleration as the function of NaI concentration is much smaller than that of NaCl or NaBr. The gold dissolution ability has been examined also for nitrous acid containing chloride and bromide ions at 35 °C. The NaNO2 solution containing twice or more amounts of HX (X = Cl, Br) gives the maximum efficiency for gold dissolution, according to the log(k/s(-1)) values of the mixed solutions of NaNO2 (0.10-2.0 mol L(-1)) and HX of various concentrations. The influence of oxidation by dilute nitric and nitrous acids on the gold dissolution is discussed from the standpoint of the redox potentials in "modified" aqueous solutions and not of the changes in the activity coefficients of ions.

  19. Infusion of branched-chain enriched amino acid solution in patients with hepatic encephalopathy.

    PubMed

    Freund, H; Dienstag, J; Lehrich, J; Yoshimura, N; Bradford, R R; Rosen, H; Atamian, S; Slemmer, E; Holroyde, J; Fischer, J E

    1982-08-01

    Hospitalized patients with hepatic insufficiency often suffer from severe catabolic states and are in urgent need of nutritional support during their acute illness. Protein intolerence, however, remains a significant problem with respect to the provision of adequate nutrition, either enterally or parenterally. The following report is an anecdotal series of 63 consecutive patients in a large urban hospital treated prospectively with nutritional support using a prototype high branched-chain amino acid solution (FO80) given by technique of total parenteral nutrition by the subclavian or internal jugular route with hypertonic dextrose. Sixty-three patients, of which 42 had chronic liver disease (cirrhosis) with acute decompensation and 17 with acute hepatic injury as well as four with hepatorenal syndrome, are the subject of this report. All required intravenous nutritional support and were either intolerant to commercially available parenteral nutrition solutions or were in hepatic encephalopathy at the time they were initially seen. The cirrhotic patients had been hospitalized for a mean of 14.5 +/- 1.9 days before therapy, had a mean bilirubin of 13 mg/100 ml, and had been in coma for 4.8 +/- 0.7 days despite standard therapy. Patients with acute hepatitis had been in the hospital for 16.2 +/- 4.1 days before therapy, had a mean bilirubin of 25 mg/100 ml, and had been in coma 5.2 +/- 1.6 days before therapy. Routine tests of liver function, blood chemistries, amino acids, EEGs, and complex neurological testing including Reitan trailmaking tests were used in the evaluation of these patients. Up to 120 grams of synthetic amino acid solution with hypertonic dextrose was tolerated in these patients with improvement noted in encephalopathy of at least one grade in 87% of the patients with cirrhosis and 75% of the patients with hepatitis. Nitrogen balance was achieved when 75 to 80 grams of synthetic amino acids were administered. Survival was 45% in the cirrhotic group

  20. Analysis of acrylamido-buffers for isoelectric focusing by capillary zone electrophoresis.

    PubMed

    Righetti, P G; Ettori, C; Chiari, M

    1991-01-01

    Immobilized pH gradients use a series of weak acrylamido acids and bases (Immobiline) to create a pH gradient along the separation axis. These buffers can be degraded in water by two mechanisms: (i) hydrolysis of the amido bond, with generation of free acrylic acid and either an amino acid or a diamine; (ii) autopolymerization to oligomers and/or n-mers. In order to check for these degradation products, different capillary zone electrophoresis systems for analysis of all Immobilines have been devised. The acidic compounds are resolved in 100 mM acetate, pH 4.0, whereas the alkaline Immobilines are separated in 50 mM phosphate buffer, pH 7.7 (or pH 7.2 for the weaker species). Polymers of alkaline Immobilines are resolved in 50 mM phosphate buffer, pH 2.5, in 1% Ficoll-400. All Immobilines are detected underivatized, by their adsorption at 214 or 254 nm. A calibration curve has been constructed for quantification of acrylic acid contamination. As little as 1 mol% of acrylic acid contamination in Immobiline solutions can be detected, with a sensitivity limit below 0.2 mM (at the injection port). PMID:2050100