Science.gov

Sample records for acid hydrolysis procedure

  1. Robustness of two-step acid hydrolysis procedure for composition analysis of poplar.

    PubMed

    Bhagia, Samarthya; Nunez, Angelica; Wyman, Charles E; Kumar, Rajeev

    2016-09-01

    The NREL standard procedure for lignocellulosic biomass composition has two steps: primary hydrolysis in 72% wt sulfuric acid at 30°C for 1h followed by secondary hydrolysis of the slurry in 4wt% acid at 121°C for 1h. Although pointed out in the NREL procedure, the impact of particle size on composition has never been shown. In addition, the effects of primary hydrolysis time and separation of solids prior to secondary hydrolysis on composition have never been shown. Using poplar, it was found that particle sizes less than 0.250mm significantly lowered the glucan content and increased the Klason lignin but did not affect xylan, acetate, or acid soluble lignin contents. Composition was unaffected for primary hydrolysis time between 30 and 90min. Moreover, separating solids prior to secondary hydrolysis had negligible effect on composition suggesting that lignin and polysaccharides are completely separated in the primary hydrolysis stage. PMID:27282557

  2. Acid hydrolysis of cellulose

    SciTech Connect

    Salazar, H.

    1980-12-01

    One of the alternatives to increase world production of etha nol is by the hydrolysis of cellulose content of agricultural residues. Studies have been made on the types of hydrolysis: enzimatic and acid. Data obtained from the sulphuric acid hydrolysis of cellulose showed that this process proceed in two steps, with a yield of approximately 95% glucose. Because of increases in cost of alternatives resources, the high demand of the product and the more economic production of ethanol from cellulose materials, it is certain that this technology will be implemented in the future. At the same time further studies on the disposal and reuse of the by-products of this production must be undertaken.

  3. A simple procedure for preparing chitin oligomers through acetone precipitation after hydrolysis in concentrated hydrochloric acid.

    PubMed

    Kazami, Nao; Sakaguchi, Masayoshi; Mizutani, Daisuke; Masuda, Tatsuhiko; Wakita, Satoshi; Oyama, Fumitaka; Kawakita, Masao; Sugahara, Yasusato

    2015-11-01

    Chitin oligomers are of interest because of their numerous biologically relevant properties. To prepare chitin oligomers containing 4-6 GlcNAc units [(GlcNAc)4-6], α- and β-chitin were hydrolyzed with concentrated hydrochloric acid at 40 °C. The reactant was mixed with acetone to recover the acetone-insoluble material, and (GlcNAc)4-6 was efficiently recovered after subsequent water extraction. Composition analysis using gel permeation chromatography and MALDI-TOF mass spectrometry indicated that (GlcNAc)4-6 could be isolated from the acetone-insoluble material with recoveries of approximately 17% and 21% from the starting α-chitin and β-chitin, respectively. The acetone precipitation method is highly useful for recovering chitin oligomers from the acid hydrolysate of chitin. The changes in the molecular size and higher-order structure of chitin during the course of hydrolysis were also analyzed, and a model that explains the process of oligomer accumulation is proposed.

  4. Acid hydrolysis of cellulose to yield glucose

    DOEpatents

    Tsao, George T.; Ladisch, Michael R.; Bose, Arindam

    1979-01-01

    A process to yield glucose from cellulose through acid hydrolysis. Cellulose is recovered from cellulosic materials, preferably by pretreating the cellulosic materials by dissolving the cellulosic materials in Cadoxen or a chelating metal caustic swelling solvent and then precipitating the cellulose therefrom. Hydrolysis is accomplished using an acid, preferably dilute sulfuric acid, and the glucose is yielded substantially without side products. Lignin may be removed either before or after hydrolysis.

  5. Acid Hydrolysis of Trioxalatocobaltate (III) Ion

    ERIC Educational Resources Information Center

    Wiggans, P. W.

    1975-01-01

    Describes an investigation involving acid hydrolysis and using both volumetric and kinetic techniques. Presents examples of the determination of the rate constant and its variation with temperature. (GS)

  6. Optimization of dilute acid hydrolysis of Enteromorpha

    NASA Astrophysics Data System (ADS)

    Feng, Dawei; Liu, Haiyan; Li, Fuchao; Jiang, Peng; Qin, Song

    2011-11-01

    Acid hydrolysis is a simple and direct way to hydrolyze polysaccharides in biomass into fermentable sugars. To produce fermentable sugars effectively and economically for fuel ethanol, we have investigated the hydrolysis of Enteromorpha using acids that are typically used to hydrolyze biomass: H2SO4, HCl, H3PO4 and C4H4O4 (maleic acid). 5%(w/w) Enteromorpha biomass was treated for different times (30, 60, and 90 min) and with different acid concentrations (0.6, 1.0, 1.4, 1.8, and 2.2%, w/w) at 121°C. H2SO4 was the most effective acid in this experiment. We then analyzed the hydrolysis process in H2SO4 in detail using high performance liquid chromatography. At a sulfuric acid concentration of 1.8% and treatment time of 60 min, the yield of ethanol fermentable sugars (glucose and xylose) was high, (230.5 mg/g dry biomass, comprising 175.2 mg/g glucose and 55.3 mg/g xylose), with 48.6% of total reducing sugars being ethanol fermentable. Therefore, Enteromorpha could be a good candidate for production of fuel ethanol. In future work, the effects of temperature and biomass concentration on hydrolysis, and also the fermentation of the hydrolysates to ethanol fuel should be focused on.

  7. Validation of lignocellulosic biomass carbohydrates determination via acid hydrolysis.

    PubMed

    Zhou, Shengfei; Runge, Troy M

    2014-11-01

    This work studied the two-step acid hydrolysis for determining carbohydrates in lignocellulosic biomass. Estimation of sugar loss based on acid hydrolyzed sugar standards or analysis of sugar derivatives was investigated. Four model substrates (starch, holocellulose, filter paper and cotton) and three levels of acid/material ratios (7.8, 10.3 and 15.4, v/w) were studied to demonstrate the range of test artifacts. The method for carbohydrates estimation based on acid hydrolyzed sugar standards having the most satisfactory carbohydrate recovery and relative standard deviation. Raw material and the acid/material ratio both had significant effect on carbohydrate hydrolysis, suggesting the acid to have impacts beyond a catalyst in the hydrolysis. Following optimal procedures, we were able to reach a carbohydrate recovery of 96% with a relative standard deviation less than 3%. The carbohydrates recovery lower than 100% was likely due to the incomplete hydrolysis of substrates, which was supported by scanning electron microscope (SEM) images.

  8. Extraterrestrial material analysis: loss of amino acids during liquid-phase acid hydrolysis

    NASA Astrophysics Data System (ADS)

    Buch, Arnaud; Brault, Amaury; Szopa, Cyril; Freissinet, Caroline

    2015-04-01

    Searching for building blocks of life in extraterrestrial material is a way to learn more about how life could have appeared on Earth. With this aim, liquid-phase acid hydrolysis has been used, since at least 1970 , in order to extract amino acids and other organic molecules from extraterrestrial materials (e.g. meteorites, lunar fines) or Earth analogues (e.g. Atacama desert soil). This procedure involves drastic conditions such as heating samples in 6N HCl for 24 h, either under inert atmosphere/vacuum, or air. Analysis of the hydrolyzed part of the sample should give its total (free plus bound) amino acid content. The present work deals with the influence of the 6N HCl hydrolysis on amino acid degradation. Our experiments have been performed on a standard solution of 17 amino acids. After liquid-phase acid hydrolysis (6N HCl) under argon atmosphere (24 h at 100°C), the liquid phase was evaporated and the dry residue was derivatized with N-Methyl-N-(t-butyldimethylsilyl)trifluoroacetamide (MTBSTFA) and dimethylformamide (DMF), followed by gas chromatography-mass spectrometry analysis. After comparison with derivatized amino acids from the standard solution, a significant reduction of the chromatographic peak areas was observed for most of the amino acids after liquid-phase acid hydrolysis. Furthermore, the same loss pattern was observed when the amino acids were exposed to cold 6N HCl for a short amount of time. The least affected amino acid, i.e. glycine, was found to be 73,93% percent less abundant compared to the non-hydrolyzed standard, while the most affected, i.e. histidine, was not found in the chromatograms after hydrolysis. Our experiments thereby indicate that liquid-phase acid hydrolysis, even under inert atmosphere, leads to a partial or total loss of all of the 17 amino acids present in the standard solution, and that a quick cold contact with 6N HCl is sufficient to lead to a loss of amino acids. Therefore, in the literature, the reported increase

  9. Acid-functionalized nanoparticles for biomass hydrolysis

    NASA Astrophysics Data System (ADS)

    Pena Duque, Leidy Eugenia

    Cellulosic ethanol is a renewable source of energy. Lignocellulosic biomass is a complex material composed mainly of cellulose, hemicellulose, and lignin. Biomass pretreatment is a required step to make sugar polymers liable to hydrolysis. Mineral acids are commonly used for biomass pretreatment. Using acid catalysts that can be recovered and reused could make the process economically more attractive. The overall goal of this dissertation is the development of a recyclable nanocatalyst for the hydrolysis of biomass sugars. Cobalt iron oxide nanoparticles (CoFe2O4) were synthesized to provide a magnetic core that could be separated from reaction using a magnetic field and modified to carry acid functional groups. X-ray diffraction (XRD) confirmed the crystal structure was that of cobalt spinel ferrite. CoFe2O4 were covered with silica which served as linker for the acid functions. Silica-coated nanoparticles were functionalized with three different acid functions: perfluoropropyl-sulfonic acid, carboxylic acid, and propyl-sulfonic acid. Transmission electron microscope (TEM) images were analyzed to obtain particle size distributions of the nanoparticles. Total carbon, nitrogen, and sulfur were quantified using an elemental analyzer. Fourier transform infra-red spectra confirmed the presence of sulfonic and carboxylic acid functions and ion-exchange titrations accounted for the total amount of catalytic acid sites per nanoparticle mass. These nanoparticles were evaluated for their performance to hydrolyze the beta-1,4 glycosidic bond of the cellobiose molecule. Propyl-sulfonic (PS) and perfluoropropyl-sulfonic (PFS) acid functionalized nanoparticles catalyzed the hydrolysis of cellobiose significantly better than the control. PS and PFS were also evaluated for their capacity to solubilize wheat straw hemicelluloses and performed better than the control. Although PFS nanoparticles were stronger acid catalysts, the acid functions leached out of the nanoparticle during

  10. Enhanced functional properties of tannic acid after thermal hydrolysis

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Thermal hydrolysis processing of fresh tannic acid was carried out in a closed reactor at four different temperatures (65, 100, 150 and 200°C). Pressures reached in the system were 1.3 and 4.8 MPa at 150 and 200°C, respectively. Hydrolysis products (gallic acid and pyrogallol) were separated and qua...

  11. Acid and enzymatic hydrolysis of pretreated cellulosic materials as an analytical tool

    SciTech Connect

    Ladisch, C.M.; Chiasson, C.M.; Tsao, G.T.

    1982-07-01

    A rapid and accurate procedure for the quantitative analysis of cellulose in textiles based on acid and enzymatic hydrolysis was investigated. Total hydrolysis was achieved by a two-step procedure: the cellulose in the sample was first dissolved in cadoxen and then reprecipitated. The material, thus pretreated, was then hydrolyzed with acid or enzyme catalytic agents. Hydrolysis products were detected and quantified by colorimetric, enzymic, and liquid chromatographic methods of analysis. Samples examined included cotton, rayon, Avicel, CF-11, and cotton/polyester blends. The specificity of the enzyme hydrolysis method allowed analysis of raw cotton without prior purification. Results of the analyses were compared to those obtained by existing methods of analysis.

  12. Assay of phenolic compounds from four species of Ber (Ziziphus mauritiana L.) Fruits: Comparision of three base hydrolysis procedure for quantification of total phenolic acids

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The present study was undertaken to investigate the flavonoids profile in four species of ber (Ziziphus mauritiana Lamk) fruit and to compare various techniques for the analysis of total phenolic acids. The 12 flavonoids identified were quercetin 3-O-robinobioside, quercetin 3-O-rutinoside, querceti...

  13. ESTIMATION OF CARBOXYLIC ACID ESTER HYDROLYSIS RATE CONSTANTS

    EPA Science Inventory

    SPARC chemical reactivity models were extended to calculate hydrolysis rate constants for carboxylic acid esters from molecular structure. The energy differences between the initial state and the transition state for a molecule of interest are factored into internal and external...

  14. Partial acid hydrolysis of poplar wood as a pretreatment for enzymatic hydrolysis

    SciTech Connect

    Knappert, D.; Grethlein, H.; Converse, A.

    1981-01-01

    Partial acid hydrolysis was studied as a pretreatment to enhance glucose yields from enzymatic hydrolysis of poplar. The pretreatments were carried out in a continuous flow reactor at temperatures ranging from 162 to 222/sup 0/C, acid concentrations ranging from 0 to 1.5%, and treatment times from 3.6 to 12.7 s. The pretreated slurries were hydrolyzed with Trichoderma reesei C30 cellulase at 50/sup 0/C and a pH of 4.8 for 48 h. Increased yields of glucose were achieved when poplar was pretreated at temperatures higher than 180/sup 0/C. By increasing the cellobiase activity of the cellulase with the addition of NOVO cellobiase, in some cases 100% of the potential glucose content of the substrate was converted to glucose after only 24 h of enzymatic hydrolysis.

  15. ESTIMATION OF PHOSPHATE ESTER HYDROLYSIS RATE CONSTANTS. II. ACID AND GENERAL BASE CATALYZED HYDROLYSIS

    EPA Science Inventory

    SPARC (SPARC Performs Automated Reasoning in Chemistry) chemical reactivity models were extended to calculate acid and neutral hydrolysis rate constants of phosphate esters in water. The rate is calculated from the energy difference between the initial and transition states of a ...

  16. Acid hydrolysis of Jerusalem artichoke for ethanol fermentation

    SciTech Connect

    Kim, K.; Hamdy, M.K.

    1986-01-01

    An excellent substrate for ethanol production is the Jerusalem artichoke (JA) tuber (Helianthus tuberosus). This crop contains a high level of inulin that can be hydrolyzed mainly to D-fructose and has several distinct advantages as an energy source compared to others. The potential ethanol yield of ca. 4678 L/ha on good agricultural land is equivalent to that obtained from sugar beets and twice that of corn. When JA is to be used for ethanol fermentation by conventional yeast, it is first converted to fermentable sugars by enzymes or acids although various strains of yeast were used for the direct fermentation of JA extracts. Fleming and GrootWassink compared various acids (hydrochloric, sulfuric, citric, and phosphoric) and strong cation exchange resin for their effectiveness on inulin hydrolysis and reported that no differences were noted among the acids or resin in their influence on inulin hydrolysis. Undesirable side reactions were noted during acid hydrolysis leading to the formation of HMF and 2-(2-hydroxy acetyl) furan. The HMF at a level of 0.1% is known to inhibit growth and ethanol fermentation by yeast. In this study the authors established optimal conditions for complete acid-hydrolysis of JA with minimum side reactions and maximum sugar-ethanol production. A material balance for the ethanol production was also determined.

  17. Role of bifidobacteria in the hydrolysis of chlorogenic acid

    PubMed Central

    Raimondi, Stefano; Anighoro, Andrew; Quartieri, Andrea; Amaretti, Alberto; Tomás-Barberán, Francisco A; Rastelli, Giulio; Rossi, Maddalena

    2015-01-01

    This study aimed to explore the capability of potentially probiotic bifidobacteria to hydrolyze chlorogenic acid into caffeic acid (CA), and to recognize the enzymes involved in this reaction. Bifidobacterium strains belonging to eight species occurring in the human gut were screened. The hydrolysis seemed peculiar of Bifidobacterium animalis, whereas the other species failed to release CA. Intracellular feruloyl esterase activity capable of hydrolyzing chlorogenic acid was detected only in B. animalis. In silico research among bifidobacteria esterases identified Balat_0669 as the cytosolic enzyme likely responsible of CA release in B. animalis. Comparative modeling of Balat_0669 and molecular docking studies support its role in chlorogenic acid hydrolysis. Expression, purification, and functional characterization of Balat_0669 in Escherichia coli were obtained as further validation. A possible role of B. animalis in the activation of hydroxycinnamic acids was demonstrated and new perspectives were opened in the development of new probiotics, specifically selected for the enhanced bioconversion of phytochemicals into bioactive compounds. PMID:25515139

  18. Ethanol production with dilute acid hydrolysis using partially dried lignocellulosics

    DOEpatents

    Nguyen, Quang A.; Keller, Fred A.; Tucker, Melvin P.

    2003-12-09

    A process of converting lignocellulosic biomass to ethanol, comprising hydrolyzing lignocellulosic materials by subjecting dried lignocellulosic material in a reactor to a catalyst comprised of a dilute solution of a strong acid and a metal salt to lower the activation energy (i.e., the temperature) of cellulose hydrolysis and ultimately obtain higher sugar yields.

  19. Automated protein hydrolysis delivering sample to a solid acid catalyst for amino acid analysis.

    PubMed

    Masuda, Akiko; Dohmae, Naoshi

    2010-11-01

    In this study, we developed an automatic protein hydrolysis system using strong cation-exchange resins as solid acid catalysts. Examining several kinds of inorganic solid acids and cation-exchange resins, we found that a few cation-exchange resins worked as acid catalysts for protein hydrolysis when heated in the presence of water. The most efficient resin yielded amounts of amino acids that were over 70% of those recovered after conventional hydrolysis with hydrochloric acid and resulted in amino acid compositions matching the theoretical values. The solid-acid hydrolysis was automated by packing the resin into columns, combining the columns with a high-performance liquid chromatography system, and heating them. The amino acids that constitute a protein can thereby be determined, minimizing contamination from the environment.

  20. Carbon-based strong solid acid for cornstarch hydrolysis

    SciTech Connect

    Nata, Iryanti Fatyasari; Irawan, Chairul; Mardina, Primata; Lee, Cheng-Kang

    2015-10-15

    Highly sulfonated carbonaceous spheres with diameter of 100–500 nm can be generated by hydrothermal carbonization of glucose in the presence of hydroxyethylsulfonic acid and acrylic acid at 180 °C for 4 h. The acidity of the prepared carbonaceous sphere C4-SO{sub 3}H can reach 2.10 mmol/g. It was used as a solid acid catalyst for the hydrolysis of cornstarch. Total reducing sugar (TRS) concentration of 19.91 mg/mL could be obtained by hydrolyzing 20 mg/mL cornstarch at 150 °C for 6 h using C4-SO{sub 3}H as solid acid catalyst. The solid acid catalyst demonstrated good stability that only 9% decrease in TRS concentration was observed after five repeat uses. The as-prepared carbon-based solid acid catalyst can be an environmentally benign replacement for homogeneous catalyst. - Highlights: • Carbon solid acid was successfully prepared by one-step hydrothermal carbonization. • The acrylic acid as monomer was effectively reduce the diameter size of particle. • The solid acid catalyst show good catalytic performance of starch hydrolysis. • The solid acid catalyst is not significantly deteriorated after repeated use.

  1. Enhancement of hydrolysis of Chlorella vulgaris by hydrochloric acid.

    PubMed

    Park, Charnho; Lee, Ja Hyun; Yang, Xiaoguang; Yoo, Hah Young; Lee, Ju Hun; Lee, Soo Kweon; Kim, Seung Wook

    2016-06-01

    Chlorella vulgaris is considered as one of the potential sources of biomass for bio-based products because it consists of large amounts of carbohydrates. In this study, hydrothermal acid hydrolysis with five different acids (hydrochloric acid, nitric acid, peracetic acid, phosphoric acid, and sulfuric acid) was carried out to produce fermentable sugars (glucose, galactose). The hydrothermal acid hydrolysis by hydrochloric acid showed the highest sugar production. C. vulgaris was hydrolyzed with various concentrations of hydrochloric acid [0.5-10 % (w/w)] and microalgal biomass [20-140 g/L (w/v)] at 121 °C for 20 min. Among the concentrations examined, 2 % hydrochloric acid with 100 g/L biomass yielded the highest conversion of carbohydrates (92.5 %) into reducing sugars. The hydrolysate thus produced from C. vulgaris was fermented using the yeast Brettanomyces custersii H1-603 and obtained bioethanol yield of 0.37 g/g of algal sugars. PMID:26899601

  2. Hydrolysis of cellulose catalyzed by novel acidic ionic liquids.

    PubMed

    Zhuo, Kelei; Du, Quanzhou; Bai, Guangyue; Wang, Congyue; Chen, Yujuan; Wang, Jianji

    2015-01-22

    The conversion of cellulosic biomass directly into valuable chemicals becomes a hot subject. Six novel acidic ionic liquids (ILs) based on 2-phenyl-2-imidazoline were synthesized and characterized by UV-VIS, TGA, and NMR. The novel acidic ionic liquids were investigated as catalysts for the hydrolysis of cellulose in 1-butyl-3-methylimidazolium chloride ([Bmim]Cl). The acidic ionic liquids with anions HSO4(-) and Cl(-) showed better catalytic performance for the hydrolysis of cellulose than those with H2PO4(-). The temperature and dosage of water affect significantly the yield of total reducing sugar (TRS). When the hydrolysis of cellulose was catalyzed by 1-propyl sulfonic acid-2-phenyl imidazoline hydrogensulfate (IL-1) and the dosage of water was 0.2g, the TRS yield was up to 85.1% within 60 min at 100°C. These new acidic ionic liquids catalysts are expected to have a wide application in the conversion of cellulose into valuable chemicals. PMID:25439867

  3. Acid hydrolysis of sweet potato for ethanol production

    SciTech Connect

    Kim, K.; Hamdy, M.K.

    1985-01-01

    Studies were conducted to establish optimal conditions for the acid hydrolysis of sweet potato for maximal ethanol yield. The starch contents of two sweet potato cultivars (Georgia Red and TG-4), based on fresh weight, were 21.1 +/- 0.6% and 27.5 +/- 1.6%, respectively. The results of acid hydrolysis experiments showed the following: (1) both hydrolysis rate and hydroxymethylfurfural (HMF) concentration were a function of HCL concentration, temperature, and time; (2) the reducing sugars were rapidly formed with elevated concentrations of HCl and temperature, but also destroyed quickly; and (3) HMF concentration increased significantly with the concentration of HCl, temperature, and hydrolysis time. Maximum reducing sugar value of 84.2 DE and 0.056% HMF (based on wet weight) was achieved after heating 8% SPS for 15 min in 1N HCl at 110/sup 0/C. Degraded 8% SPS (1N HCl, 97/sup 0/C for 20 min or 110/sup 0/C for 10 min) was utilized as substrate for ethanol fermentation and 3.8% ethanol (v/v) was produced from 1400 mL fermented wort. This is equal to 41.6 g ethanol (200 proof) from 400 g of fresh sweet potato tuber (Georgia Red) or an ethanol yield potential of 431 gal of 200-proof ethanol/acre (from 500 bushel tubers/acre).

  4. Carbon-based strong solid acid for cornstarch hydrolysis

    NASA Astrophysics Data System (ADS)

    Nata, Iryanti Fatyasari; Irawan, Chairul; Mardina, Primata; Lee, Cheng-Kang

    2015-10-01

    Highly sulfonated carbonaceous spheres with diameter of 100-500 nm can be generated by hydrothermal carbonization of glucose in the presence of hydroxyethylsulfonic acid and acrylic acid at 180 °C for 4 h. The acidity of the prepared carbonaceous sphere C4-SO3H can reach 2.10 mmol/g. It was used as a solid acid catalyst for the hydrolysis of cornstarch. Total reducing sugar (TRS) concentration of 19.91 mg/mL could be obtained by hydrolyzing 20 mg/mL cornstarch at 150 °C for 6 h using C4-SO3H as solid acid catalyst. The solid acid catalyst demonstrated good stability that only 9% decrease in TRS concentration was observed after five repeat uses. The as-prepared carbon-based solid acid catalyst can be an environmentally benign replacement for homogeneous catalyst.

  5. Hydrolysis of aceto-hydroxamic acid under UREX+ conditions

    SciTech Connect

    Alyapyshev, M.; Paulenova, A.; Tkac, P.; Cleveland, M.A.; Bruso, J.E.

    2007-07-01

    Aceto-hydroxamic acid (AHA) is used as a stripping agent In the UREX process. While extraction yields of uranium remain high upon addition of AHA, hexavalent plutonium and neptunium are rapidly reduced to the pentavalent state while the tetravalent species and removed from the product stream. However, under acidic conditions, aceto-hydroxamic acid undergoes hydrolytic degradation. In this study, the kinetics of the hydrolysis of aceto-hydroxamic acid in nitric and perchloric acid media was investigated at several temperatures. The decrease of the concentration of AHA was determined via its ferric complex using UV-Vis spectroscopy. The data obtained were analyzed using the method of initial rates. The data follow the pseudo-first order reaction model. Gamma irradiation of AHA/HNO{sub 3} solutions with 33 kGy/s caused two-fold faster degradation of AHA. The rate equation and thermodynamic data will be presented for the hydrolysis reaction with respect to the concentrations of aceto-hydroxamic acid, nitrate and hydronium ions, and radiation dose. (authors)

  6. Fatty acid hydrolysis of acyl marinobactin siderophores by Marinobacter acylases.

    PubMed

    Kem, Michelle P; Naka, Hiroaki; Iinishi, Akira; Haygood, Margo G; Butler, Alison

    2015-01-27

    The marine bacteria Marinobacter sp. DS40M6 and Marinobacter nanhaiticus D15-8W produce a suite of acyl peptidic marinobactin siderophores to acquire iron under iron-limiting conditions. During late-log phase growth, the marinobactins are hydrolyzed to form the marinobactin headgroup with release of the corresponding fatty acid tail. The bntA gene, a homologue of the Pseudomonas aeruginosa pyoverdine acylase gene, pvdQ, was identified from Marinobacter sp. DS40M6. A bntA knockout mutant of Marinobacter sp. DS40M6 produced the suite of acyl marinobactins A-E, without the usual formation of the marinobactin headgroup. Another marinobactin-producing species, M. nanhaiticus D15-8W, is predicted to have two pvdQ homologues, mhtA and mhtB. MhtA and MhtB have 67% identical amino acid sequences. MhtA catalyzes hydrolysis of the apo-marinobactin siderophores as well as the quorum sensing signaling molecule, dodecanoyl-homoserine lactone. In contrast to hydrolysis of the suite of apo-marinobactins by MhtA, hydrolysis of the iron(III)-bound marinobactins was not observed. PMID:25588131

  7. Dilute-acid hydrolysis of sugarcane bagasse at varying conditions.

    PubMed

    Neureiter, Markus; Danner, Herbert; Thomasser, Christiane; Saidi, Bamusi; Braun, Rudolf

    2002-01-01

    Sugarcane bagasse, a byproduct of the cane sugar industry, is an abundant source of hemicellulose that could be hydrolyzed to yield a fermentation feedstock for the production of fuel ethanol and chemicals. The effects of sulfuric acid concentration, temperature, time, and dry matter concentration on hemicellulose hydrolysis were studied with a 20-L batch hydrolysis reactor using a statistical experimental design. Even at less severe conditions considerable amounts (>29%) of the hemicellulose fraction could be extracted. The percentage of soluble oligosaccharides becomes very low in experiments with high yields in monosaccharides, which indicates that the cellulose fraction is only slightly affected. For the sugar yields, acid concentration appears to be the most important parameter, while for the formation of sugar degradation products, temperature shows the highest impact. It could be demonstrated that the dry matter concentration in the reaction slurry has a negative effect on the xylose yield that can be compensated by higher concentrations of sulfuric acid owing to a positive interaction between acid concentration and dry matter contents.

  8. Chemical evolution. XXI - The amino acids released on hydrolysis of HCN oligomers

    NASA Technical Reports Server (NTRS)

    Ferris, J. P.; Wos, J. D.; Nooner, D. W.; Oro, J.

    1974-01-01

    Major amino acids released by hydrolysis of acidic and basic HCN oligomers are identified by chromatography as Gly, Asp, and diaminosuccinic acid. Smaller amounts of Ala, Ile and alpha-aminoisobutyric acid are also detected. The amino acids released did not change appreciably when the hydrolysis medium was changed from neutral to acidic or basic. The presence of both meso and d, l-diaminosuccinic acids was established by paper chromatography and on an amino acid analyzer.

  9. Activation Energies for an Enzyme-Catalyzed and Acid-Catalyzed Hydrolysis: An Introductory Interdisciplinary Experiment for Chemists and Biochemists.

    ERIC Educational Resources Information Center

    Adams, K. R.; Meyers, M. B.

    1985-01-01

    Background information, procedures used, and typical results obtained are provided for an experiment in which students determine and compare the Arrhenius activation energies (Ea) for the hydrolysis of salicin. This reaction is subject to catalysis both by acid and by the enzyme emulsin (beta-d-glucoside glycohydrolase). (JN)

  10. Zip nucleic acids are potent hydrolysis probes for quantitative PCR

    PubMed Central

    Paris, Clément; Moreau, Valérie; Deglane, Gaëlle; Voirin, Emilie; Erbacher, Patrick; Lenne-Samuel, Nathalie

    2010-01-01

    Zip nucleic acids (ZNAs) are oligonucleotides conjugated with cationic spermine units that increase affinity for their target. ZNAs were recently shown to enable specific and sensitive reactions when used as primers for polymerase chain reaction (PCR) and reverse-transcription. Here, we report their use as quantitative PCR hydrolysis probes. Ultraviolet duplex melting data demonstrate that attachment of cationic residues to the 3′ end of an oligonucleotide does not alter its ability to discriminate nucleotides nor the destabilization pattern relative to mismatch location in the oligonucleotide sequence. The stability increase provided by the cationic charges allows the use of short dual-labeled probes that significantly improve single-nucleotide polymorphism genotyping. Longer ZNA probes were shown to display reduced background fluorescence, therefore, generating greater sensitivity and signal level as compared to standard probes. ZNA probes thus provide broad flexibility in assay design and also represent an effective alternative to minor groove binder- and locked nucleic-acid-containing probes. PMID:20071749

  11. Kinetic and process studies on free and solid acid catalyzed hydrolysis of biomass substrates

    SciTech Connect

    Abasaeed, A.E.

    1987-01-01

    Trifluoroacetic acid (TFA) was tested as a catalyst for cellulose hydrolysis. Eighty percent conversion of cellulose into glucose was obtained with concentrated TFA. The kinetics of TFA catalyzed cellulose hydrolysis was investigated. The reaction was found to follow first order kinetics for both hydrolysis and decomposition. The kinetic parameters were determined from experimental data covering conditions of 160-180 C, 10-30% acid, and 1:2 solid to liquid ratio. The hydrolysis reaction was found to be more sensitive to temperature than the decomposition reaction. Use of TFA was further investigated as a pretreatment for enzymatic hydrolysis of cellulose. A two-fold increase in sugar yields was obtained for TFA pretreated samples in comparison to untreated ones. The kinetics of hydrolysis of prehydrolyzed wood by sulfuric acid was investigated. The substrate was first treated with 0.75% acid at 184 C for 4 minutes to remove hemicellulose. The kinetic parameters were determined in the range of 198-215 C and 1-3% acid. A heterogeneous kinetic model was developed to study the effect of particle size on acid hydrolysis of cellulose. It was found that as the chip size increases, maximum glucose yield decreases and reaction time at which maximum yield occurs increases. Acidic zeolites (LZ-M-8) were investigated as catalysts for hydrolysis reaction of inulin into fructose. The hydrolysis reaction was found to follow first order kinetics. Products containing 96 and 75% fructose were obtained upon hydrolysis respectively from inulin and extract.

  12. Simulation of acid hydrolysis of lignocellulosic residues to fermentable sugars for bioethanol production

    NASA Astrophysics Data System (ADS)

    Sidiras, Dimitris

    2012-12-01

    The dilute acid hydrolysis of fir sawdust with sulfuric acid was undertaken in a batch reactor system (autoclave). The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemicelluloses hydrolysis, due to a rapid hydrolysis reaction for acid concentration 0.045 N at 160-180°C. It was found that significant sugar degradation occurred at these conditions. The optimum conditions gave a yield of 38% total fermentable sugars. The kinetics of dilute acid hydrolysis of cellulose and hemicelluloses (polysaccharides) were simulated using four pseudo-kinetic models. The reaction rate constants were calculated in each case.

  13. Effect of acid hydrolysis on starch structure and functionality: a review.

    PubMed

    Wang, Shujun; Copeland, Les

    2015-01-01

    Acid hydrolysis is an important chemical modification that can significantly change the structural and functional properties of starch without disrupting its granular morphology. A deep understanding of the effect of acid hydrolysis on starch structure and functionality is of great importance for starch scientific research and its industrial applications. During acid hydrolysis, amorphous regions are hydrolyzed preferentially, which enhances the crystallinity and double helical content of acid hydrolyzed starch. This review discusses current understanding of the effect of acid hydrolysis on starch structure and functionality. The effects of acid hydrolysis on amylose content, chain length distribution of amylopectin molecules, molecular and crystalline organization (including lamellar structure) and granular morphology are considered. Functional properties discussed include swelling power, gelatinization, retrogradation, pasting, gel texture, and in vitro enzyme digestibility. The paper also highlights some promising applications of acid hydrolyzed starch (starch nanocrystals) in the preparation of biodegradable nanocomposites, bio-hydrogen, and slowly digestible starch-based healthy foods.

  14. Hydrolysis of organosolv wheat pulp in formic acid at high temperature for glucose production.

    PubMed

    Kupiainen, Laura; Ahola, Juha; Tanskanen, Juha

    2012-07-01

    Organosolv methods can be used to delignify lignocellulosic crop residues for pulp production or to pretreat them prior to enzymatic hydrolysis for bioethanol production. In this study, organic solvent was used as an acidic hydrolysis catalyst to produce glucose. Hydrolysis experiments were carried out in 5-20% formic acid at 180-220 °C. Wheat straw pulp delignified with a formicodeli™ method was used as a raw material. It was found that glucose yields from pulp are significantly higher than yields from microcrystalline cellulose, a model component for cellulose hydrolysis. The results indicate that cellulose hydrolysis of real fibers takes place more selectively to glucose than hydrolysis of microcrystalline cellulose particles does. The effect of the particle size on pulp hydrolysis was investigated, the crystallinity of hydrolyzed pulp was measured by XRD analysis, and the product distribution and its influence on the process was discussed. PMID:22609651

  15. Comparison of Enzymatic Hydrolysis and Acid Hydrolysis of Sterol Glycosides from Foods Rich in Δ(7)-Sterols.

    PubMed

    Münger, Linda H; Jutzi, Sabrina; Lampi, Anna-Maija; Nyström, Laura

    2015-08-01

    In this study, we present the difference in sterol composition of extracted steryl glycosides (SG) hydrolyzed by either enzymatic or acid hydrolysis. SG were analyzed from foods belonging to the plant families Cucurbitaceae (melon and pumpkin seeds) and Amaranthaceae (amaranth and beetroot), both of which are dominated by Δ(7)-sterols. Released sterols were quantified by gas chromatography with a flame ionization detector (GC-FID) and identified using gas chromatography/mass spectrometry (GC-MS). All Δ(7)-sterols identified (Δ(7)-stigmastenyl, spinasteryl, Δ(7)-campesteryl, Δ(7)-avenasteryl, poriferasta-7,25-dienyl and poriferasta-7,22,25-trienyl glucoside) underwent isomerization under acidic conditions and high temperature. Sterols with an ethylidene or methylidene side chain were found to form multiple artifacts. The artifact sterols coeluted with residues of incompletely isomerized Δ(7)-sterols, or Δ(5)-sterols if present, and could be identified as Δ(8(14))-sterols on the basis of relative retention time, and their MS spectra as trimethylsilyl (TMS) and acetate derivatives. For instance, SG from melon were composed of 66% Δ(7)-stigmastenol when enzymatic hydrolysis was performed, whereas with acid hydrolysis only 8% of Δ(7)-stigmastenol was determined. The artifact of Δ(7)-stigmastenol coeluted with residual non-isomerized spinasterol, demonstrating the high risk of misinterpretation of compositional data obtained after acid hydrolysis. Therefore, the accurate composition of SG from foods containing sterols with a double bond at C-7 can only be obtained by enzymatic hydrolysis or by direct analysis of the intact SG.

  16. Comparison of enzymatic and acid hydrolysis of bound flavor compounds in model system and grapes.

    PubMed

    Dziadas, Mariusz; Jeleń, Henryk H

    2016-01-01

    Four synthesized terpenyl-ß-D-glycopyranosides (geranyl, neryl, citronellyl, myrtenyl) were subjected to enzymatic (AR 2000, pH 5.5) and acid (citric buffer, pH 2.5) hydrolysis. Decrease of glycosides was measured by HPLC and the volatiles released--by comprehensive gas chromatography-mass spectrometry (GC × GC-ToF-MS). Enzymatic hydrolysis performed for 21 h yielded 100% degree of hydrolysis for all glycosides but citronellyl (97%). Degree of acid hydrolysis was highly dependent on type of aglycone and the conditions. The highest degree was achieved for geraniol, followed by citronellol and nerol. Myrtenylo-ß-D-glycopyranoside was the most resistant glycoside to hydrolysis. Acid hydrolysis degree was also related to temperature/time combination, the highest being for 100 °C and 2 h. In a result of enzymatic hydrolysis 85-91% of total peak areas was terpene aglycone, whereas for acid hydrolysis the area of released terpene aglycone did not exceed 1.3% of total peak area indicating almost complete decomposition/transformation of terpenyl aglycone.

  17. Investigating Mass Transport Limitations on Xylan Hydrolysis During Dilute Acid Pretreatment of Poplar

    SciTech Connect

    Mittal, Ashutosh; Pilath, Heid M.; Parent, Yves; Chatterjee, Siddharth G.; Donohoe, Bryon S.; Yarbrough, John M.; Himmel, Michael E.; Nimlos, Mark R.; Johnson, David K.

    2014-04-28

    Mass transport limitations could be an impediment to achieving high sugar yields during biomass pretreatment and thus be a critical factor in the economics of biofuels production. The objective of this work was to study the mass transfer restrictions imposed by the structure of biomass on the hydrolysis of xylan during dilute acid pretreatment of biomass. Mass transfer effects were studied by pretreating poplar wood at particle sizes ranging from 10 micrometers to 10 mm. This work showed a significant reduction in the rate of xylan hydrolysis in poplar when compared to the intrinsic rate of hydrolysis for isolated xylan that is possible in the absence of mass transfer. In poplar samples we observed no significant difference in the rates of xylan hydrolysis over more than two orders of magnitude in particle size. It appears that no additional mass transport restrictions are introduced by increasing particle size from 10 micrometers to 10 mm. This work suggests that the rates of xylan hydrolysis in biomass particles are limited primarily by the diffusion of hydrolysis products out of plant cell walls. A mathematical description is presented to describe the kinetics of xylan hydrolysis that includes transport of the hydrolysis products through biomass into the bulk solution. The modeling results show that the effective diffusion coefficient of the hydrolysis products in the cell wall is several orders of magnitude smaller than typical values in other applications signifying the role of plant cell walls in offering resistance to diffusion of the hydrolysis products.

  18. Effect of an acid filler on hydrolysis and biodegradation of poly-lactic acid (PLA)

    NASA Astrophysics Data System (ADS)

    Iozzino, Valentina; Speranza, Vito; Pantani, Roberto

    2015-12-01

    The use of biodegradable polymers is certainly an excellent strategy to solve many of the problems related to the disposal of the traditional polymers, whose accumulation in the environment is harmful and damaging. In order to optimize the use of biodegradable polymers, it is very important to understand and control the transformation processes, the structures and the morphologies resulting from the process conditions used to produce the articles and, not least, the biodegradation. The latter is strictly dependent on the just mentioned variables. The poly-lactic acid, PLA, is a biodegradable polymer. Many studies have been carried out on the degradation process of this polymer. In the course of this work we performed degradation tests on the PLA, with a specific D-isomer content, having amorphous structure, and in particular of biodegradation and hydrolysis. An acid chemical, fumaric acid, was added to PLA with the objective of controlling the rate of hydrolysis and of biodegradation. The hydrolysis process was followed, as function of time, by means of different techniques: pH variation, variation of weight of samples and variation of crystallinity degree and glass transition temperature using DSC analysis. The samples were also analyzed in terms of biodegradability by means of a homemade respirometer apparatus, in controlled composting conditions.

  19. Impact of α-amylase combined with hydrochloric acid hydrolysis on structure and digestion of waxy rice starch.

    PubMed

    Li, Hongyan; Zhu, Yanqiao; Jiao, Aiquan; Zhao, Jianwei; Chen, Xiaoming; Wei, Benxi; Hu, Xiuting; Wu, Chunsen; Jin, Zhengyu; Tian, Yaoqi

    2013-04-01

    The structure and in vitro digestibility of native waxy rice starch by the combined hydrolysis of α-amylase and hydrochloric acid were investigated in this study. The combined hydrolysis technique generated higher hydrolysis rate and extent than the enzymatic hydrolysis. The granular appearance and chromatograph profile demonstrated that α-amylase and hydrochloric acid exhibited different patterns of hydrolysis. The rise in the ratio of absorbance 1047/1022cm(-1), the melting temperature range (Tc-To), and the melting enthalpy (ΔH) were observed during the combined hydrolysis. These results suggest that α-amylase simultaneously cleaves the amorphous and crystalline regions, whereas the amorphous regions of starch granules are preferentially hydrolyzed during the acid hydrolysis. Furthermore, the combined hydrolysis increased rapidly digestible starch (RDS) while decreased slowly digestible starch (SDS) and resistant starch (RS), indicating that the hydrolysis mode affected the digestion property of native waxy rice starch.

  20. Acid hydrolysis of cellulosic fibres: Comparison of bleached kraft pulp, dissolving pulps and cotton textile cellulose.

    PubMed

    Palme, Anna; Theliander, Hans; Brelid, Harald

    2016-01-20

    The behaviour of different cellulosic fibres during acid hydrolysis has been investigated and the levelling-off degree of polymerisation (LODP) has been determined. The study included a bleached kraft pulp (both never-dried and once-dried) and two dissolving pulps (once-dried). Additionally, cotton cellulose from new cotton sheets and sheets discarded after long-time use was studied. Experimental results from the investigation, together with results found in literature, imply that ultrastructural differences between different fibres affect their susceptibility towards acid hydrolysis. Drying of a bleached kraft pulp was found to enhance the rate of acid hydrolysis and also result in a decrease in LODP. This implies that the susceptibility of cellulosic fibres towards acid hydrolysis is affected by drying-induced stresses in the cellulose chains. In cotton cellulose, it was found that use and laundering gave a substantial loss in the degree of polymerisation (DP), but that the LODP was only marginally affected.

  1. Hydrolysis of tRNA(sup Phe) on Suspensions of Amino Acids

    NASA Technical Reports Server (NTRS)

    Gao, Kui; Orgel, Leslie E.

    2001-01-01

    RNA is adsorbed strongly on suspensions of many moderately soluble organic solids. In some cases, the hydrolysis of tRNA(sup Phe) is greatly accelerated by adsorption, and the major sites of hydrolysis are changed from those that are important in homogeneous solution. Here we show that the hydrolysis is greatly accelerated by suspensions of aspartic acid and beta-glutamic acid but not by suspensions of alpha-glutamic acid, asparagine, or glutamine. The non-enzymatic hydrolysis of RNA has been studied extensively, especially because of its relevance to the mechanisms of action of ribozymes and to biotechnology and therapy. Many ribonucleases, ribozymes, and non-biological catalysts function via acid-base catalysis of an intramolecular transesterification mechanism in which the 2'-OH group attacks the adjacent phosphate group. The pentacoordinated phosphorane intermediate may collapse back to starting material, or yield isomerized or cleaved products.

  2. On the Brønsted acid-catalyzed homogeneous hydrolysis of furans.

    PubMed

    Nikbin, Nima; Caratzoulas, Stavros; Vlachos, Dionisios G

    2013-11-01

    Furan affairs: Electronic structure calculations of the homogeneous Brønsted acid-catalyzed hydrolysis of 2,5-dimethylfuran show that proton transfer to the β-position is rate-limiting and provides support that the hydrolysis follows general acid catalysis. By means of projected Fukui indices, we show this to be the case for unsubstituted, 2-, and 2,5-substituted furans with electron-donating groups.

  3. Assessment of the hydrolysis process for the determination of okadaic acid-group toxin ester: presence of okadaic acid 7-O-acyl-ester derivates in Spanish shellfish.

    PubMed

    Villar-González, A; Rodríguez-Velasco, M L; Ben-Gigirey, B; Yasumoto, T; Botana, L M

    2008-04-01

    The contamination of different types of shellfish by okadaic acid (OA)-group toxin esters is an important problem that presents serious risk for human health. During previous investigations carried out in our laboratory by liquid chromatography coupled with tandem mass spectrometry (LC/MS/MS), the occurrence of a high percentage of esters in relation to the total OA equivalents has been observed in several shellfish species. The determination of these kinds of toxins using LC/MS or other chemical methods requires a hydrolysis step in order to convert the sterified compounds into the parent toxins, OA, dinophysistoxins-1 (DTX-1) and dinophysistoxins-2 (DTX-2). Most of the hydrolysis procedures are based on an alkaline hydrolysis reaction. However, despite hydrolysis being a critical step within the analysis, it has not been studied in depth up to now. The present paper reports the results obtained after evaluating the hydrolysis process of an esterified form of OA by using a standard of 7-O-acyl ester with palmitoyl as the fatty acid (palOA). Investigations were focused on checking the effectiveness of the hydrolysis for palOA using methanol as solvent standard and matrices matched standards. From the results obtained, no matrix influence on the hydrolysis process was observed and the quantity of palOA converted into OA was always above 80%. The analyses of different Spanish shellfish samples showed percentages of palOA in relation to the total OA esters ranging from 27% to 90%, depending on the shellfish specie. PMID:18243269

  4. Assessment of the hydrolysis process for the determination of okadaic acid-group toxin ester: presence of okadaic acid 7-O-acyl-ester derivates in Spanish shellfish.

    PubMed

    Villar-González, A; Rodríguez-Velasco, M L; Ben-Gigirey, B; Yasumoto, T; Botana, L M

    2008-04-01

    The contamination of different types of shellfish by okadaic acid (OA)-group toxin esters is an important problem that presents serious risk for human health. During previous investigations carried out in our laboratory by liquid chromatography coupled with tandem mass spectrometry (LC/MS/MS), the occurrence of a high percentage of esters in relation to the total OA equivalents has been observed in several shellfish species. The determination of these kinds of toxins using LC/MS or other chemical methods requires a hydrolysis step in order to convert the sterified compounds into the parent toxins, OA, dinophysistoxins-1 (DTX-1) and dinophysistoxins-2 (DTX-2). Most of the hydrolysis procedures are based on an alkaline hydrolysis reaction. However, despite hydrolysis being a critical step within the analysis, it has not been studied in depth up to now. The present paper reports the results obtained after evaluating the hydrolysis process of an esterified form of OA by using a standard of 7-O-acyl ester with palmitoyl as the fatty acid (palOA). Investigations were focused on checking the effectiveness of the hydrolysis for palOA using methanol as solvent standard and matrices matched standards. From the results obtained, no matrix influence on the hydrolysis process was observed and the quantity of palOA converted into OA was always above 80%. The analyses of different Spanish shellfish samples showed percentages of palOA in relation to the total OA esters ranging from 27% to 90%, depending on the shellfish specie.

  5. Modeling the hydrolysis of perfluorinated compounds containing carboxylic and phosphoric acid ester functions and sulfonamide groups.

    PubMed

    Rayne, Sierra; Forest, Kaya

    2010-01-01

    Temperature-dependent rate constants were estimated for the acid- and base-catalyzed and neutral hydrolysis reactions of perfluorinated telomer acrylates (FTAcrs) and phosphate esters (FTPEs), and the S(N)1 and S(N)2 hydrolysis reactions of fluorotelomer iodides (FTIs). Under some environmental conditions, hydrolysis of monomeric FTAcrs could be rapid (half-lives of several years in marine systems and as low as several days in some landfills) and represent a dominant portion of their overall degradation. Abiotic hydrolysis of monomeric FTAcrs may be a significant contributor to current environmental loadings of fluorotelomer alcohols (FTOHs) and perfluoroalkyl carboxylic acids (PFCAs). Polymeric FTAcrs are expected to be hydrolyzed more slowly, with estimated half-lives in soil and natural waters ranging between several centuries to several millenia absent additional surface area limitations on reactivity. Poor agreement was found between the limited experimental data on FTPE hydrolysis and computational estimates, requiring more detailed experimental data before any further modeling can occur on these compounds or their perfluoroalkyl sulfonamidoethanol phosphate ester (PFSamPE) analogs. FTIs are expected to have hydrolytic half-lives of about 130 days in most natural waters, suggesting they may be contributing to substantial FTOH and PFCA inputs in aquatic systems. Perfluoroalkyl sulfonamides (PFSams) appear unlikely to undergo abiotic hydrolysis at the S-N, C-S, or N-C linkages under environmentally relevant conditions, although potentially facile S-N hydrolysis via intramolecular catalysis by ethanol and acetic acid amide substituents warrants further investigation. PMID:20390888

  6. Studying Cellulose Fiber Structure by SEM, XRD, NMR and Acid Hydrolysis

    SciTech Connect

    Zhao, Haibo; Kwak, Ja Hun; Zhang, Z. Conrad; Brown, Heather M.; Arey, Bruce W.; Holladay, John E.

    2007-03-21

    Cotton linters were partially hydrolyzed in dilute acid and the morphology of remaining macrofibrils studied with Scanning Electron Microscopy (SEM) under various magnifications. The crystal region (microfibril bundles) in the macrofibrils was not altered by hydrolysis, and only amorphous cellulose was hydrolyzed and leached out from the macrofibrils. The diameter of microfibril bundles was 20-30 nm after the amorphous cellulose was removed by hydrolysis. XRD experiments confirm the unaltered diameter of the microfibrils after hydrolysis. The strong stability of these microfibril bundles in hydrolysis limits both the total sugar monomer yield and the size of nano particles or rods produced in hydrolysis. The large surface potential on the remaining microfibril bundles drives the agglomeration of macrofibrils.

  7. Obtaining fermentable sugars by dilute acid hydrolysis of hemicellulose and fast pyrolysis of cellulose.

    PubMed

    Jiang, Liqun; Zheng, Anqing; Zhao, Zengli; He, Fang; Li, Haibin; Liu, Weiguo

    2015-04-01

    The objective of this study was to get fermentable sugars by dilute acid hydrolysis of hemicellulose and fast pyrolysis of cellulose from sugarcane bagasse. Hemicellulose could be easily hydrolyzed by dilute acid as sugars. The remained solid residue of acid hydrolysis was utilized to get levoglucosan by fast pyrolysis economically. Levoglucosan yield from crystalline cellulose could be as high as 61.47%. Dilute acid hydrolysis was also a promising pretreatment for levoglucosan production from lignocellulose. The dilute acid pretreated sugarcane bagasse resulted in higher levoglucosan yield (40.50%) in fast pyrolysis by micropyrolyzer, which was more effective than water washed (29.10%) and un-pretreated (12.84%). It was mainly ascribed to the effective removal of alkali and alkaline earth metals and the accumulation of crystalline cellulose. This strategy seems a promising route to achieve inexpensive fermentable sugars from lignocellulose for biorefinery. PMID:25690683

  8. Obtaining fermentable sugars by dilute acid hydrolysis of hemicellulose and fast pyrolysis of cellulose.

    PubMed

    Jiang, Liqun; Zheng, Anqing; Zhao, Zengli; He, Fang; Li, Haibin; Liu, Weiguo

    2015-04-01

    The objective of this study was to get fermentable sugars by dilute acid hydrolysis of hemicellulose and fast pyrolysis of cellulose from sugarcane bagasse. Hemicellulose could be easily hydrolyzed by dilute acid as sugars. The remained solid residue of acid hydrolysis was utilized to get levoglucosan by fast pyrolysis economically. Levoglucosan yield from crystalline cellulose could be as high as 61.47%. Dilute acid hydrolysis was also a promising pretreatment for levoglucosan production from lignocellulose. The dilute acid pretreated sugarcane bagasse resulted in higher levoglucosan yield (40.50%) in fast pyrolysis by micropyrolyzer, which was more effective than water washed (29.10%) and un-pretreated (12.84%). It was mainly ascribed to the effective removal of alkali and alkaline earth metals and the accumulation of crystalline cellulose. This strategy seems a promising route to achieve inexpensive fermentable sugars from lignocellulose for biorefinery.

  9. Highly acidic mesostructured aluminosilicates assembled from surfactant-mediated zeolite hydrolysis products.

    PubMed

    Wang, Hui; Liu, Yu; Pinnavaia, Thomas J

    2006-03-16

    The surfactant-mediated hydrolysis of ZSM-5 zeolite affords five-membered ring subunits that can be readily incorporated into the framework walls of a hexagonal mesostructured aluminosilicate, denoted MSU-Z. The five-membered ring subunits, which are identifiable by infrared spectroscopy, impart unprecedented acidity to the mesostructure, as judged by cumene cracking activity at 300 degrees C. Most notably, MSU-Z aluminosilicate made through the base hydrolysis of ZSM-5 in the presence of cetyltrimethylammonium ions exhibits a cumene conversion of 73%, which is 6.7-fold higher than the conversion provided by a conventional MCM-41. This approach to stabilizing zeolitic subunits through surfactant-mediated hydrolysis of zeolites appears to be general. The hydrolysis of USY zeolite under analogous hydrolytic conditions also affords zeolitic fragments that boost the acidity of the mesostructure in comparison to equivalent compositions prepared from conventional aluminosilicate precursors.

  10. Hydrolysis of Sulfur Dioxide in Small Clusters of Sulfuric Acid: Mechanistic and Kinetic Study.

    PubMed

    Liu, Jingjing; Fang, Sheng; Wang, Zhixiu; Yi, Wencai; Tao, Fu-Ming; Liu, Jing-Yao

    2015-11-17

    The deposition and hydrolysis reaction of SO2 + H2O in small clusters of sulfuric acid and water are studied by theoretical calculations of the molecular clusters SO2-(H2SO4)n-(H2O)m (m = 1,2; n = 1,2). Sulfuric acid exhibits a dramatic catalytic effect on the hydrolysis reaction of SO2 as it lowers the energy barrier by over 20 kcal/mol. The reaction with monohydrated sulfuric acid (SO2 + H2O + H2SO4 - H2O) has the lowest energy barrier of 3.83 kcal/mol, in which the cluster H2SO4-(H2O)2 forms initially at the entrance channel. The energy barriers for the three hydrolysis reactions are in the order SO2 + (H2SO4)-H2O > SO2 + (H2SO4)2-H2O > SO2 + H2SO4-H2O. Furthermore, sulfurous acid is more strongly bonded to the hydrated sulfuric acid (or dimer) clusters than the corresponding reactant (monohydrated SO2). Consequently, sulfuric acid promotes the hydrolysis of SO2 both kinetically and thermodynamically. Kinetics simulations have been performed to study the importance of these reactions in the reduction of atmospheric SO2. The results will give a new insight on how the pre-existing aerosols catalyze the hydrolysis of SO2, leading to the formation and growth of new particles.

  11. Effect of defatting on acid hydrolysis rate of maize starch with different amylose contents.

    PubMed

    Wei, Benxi; Hu, Xiuting; Zhang, Bao; Li, Hongyan; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

    2013-11-01

    The effect of defatting on the physiochemical properties and the acid hydrolysis rate of maize starch with different amylose contents was evaluated in this study. The increase in the number of pores and the stripping of starch surface layers were observed after defatting by scanning electron microscopy. X-ray diffraction spectrum showed that the peaks attributing to the amylose-lipid complex disappeared. The relative crystallinity increased by 19% for high-amylose maize starch (HMS) on defatting, while the other tested starches virtually unchanged. Differential scanning calorimetry study indicated an increase in the thermal stability for the defatted starches. Compared with native waxy maize starch, the acid hydrolysis rate of the defatted one increased by 6% after 10 days. For normal maize starch (NMS) and HMS, the higher rate of hydrolysis was observed during the first 5 days. Thereafter, the hydrolysis rate was lower than that of their native counterpart. The increase in susceptibility to acid hydrolysis (in the first 5 days) was mainly attributed to the defective and porous structures formed during defatting process, while the decrease of hydrolysis rate for NMS and HMS samples (after the first 5 days) probably resulted from the increase in the relative crystallinity.

  12. High-yield production of biosugars from Gracilaria verrucosa by acid and enzymatic hydrolysis processes.

    PubMed

    Kim, Se Won; Hong, Chae-Hwan; Jeon, Sung-Wan; Shin, Hyun-Jae

    2015-11-01

    Gracilaria verrucosa, the red alga, is a suitable feedstock for biosugar production. This study analyzes biosugar production by the hydrolysis of G. verrucosa conducted under various conditions (i.e., various acid concentrations, substrate concentrations, reaction times, and enzyme dosages). The acid hydrolysates of G. verrucosa yielded a total of 7.47g/L (37.4%) and 10.63g/L (21.26%) of reducing sugars under optimal small (30mL) and large laboratory-scale (1L) hydrolysis processes, respectively. Reducing sugar obtained from acid and enzymatic hydrolysates were 10% higher, with minimum by-products, than those reported in other studies. The mass balance for the small laboratory-scale process showed that the acid and enzymatic hydrolysates had a carbohydrate conversion of 57.2%. The mass balance approach to the entire hydrolysis process of red seaweed for biosugar production can be applied to other saccharification processes.

  13. Preparation of κ-carra-oligosaccharides with microwave assisted acid hydrolysis method

    NASA Astrophysics Data System (ADS)

    Li, Guangsheng; Zhao, Xia; Lv, Youjing; Li, Miaomiao; Yu, Guangli

    2015-04-01

    A rapid method of microwave assisted acid hydrolysis was established to prepare κ-carra-oligosaccharides. The optimal hydrolysis condition was determined by an orthogonal test. The degree of polymerization (DP) of oligosaccharides was detected by high performance thin layer chromatography (HPTLC) and polyacrylamide gel electrophoresis (PAGE). Considering the results of HPTLC and PAGE, the optimum condition of microwave assisted acid hydrolysis was determined. The concentration of κ-carrageenan was 5 mg mL-1; the reaction solution was adjusted to pH 3 with diluted hydrochloric acid; the solution was hydrolyzed under microwave irradiation at 100 for 15 °C min. Oligosaccharides were separated by a Superdex 30 column (2.6 cm × 90 cm) using AKTA Purifier UPC100 and detected with an online refractive index detector. Each fraction was characterized by electrospray ionization mass spectrometry (ESI-MS). The data showed that odd-numbered κ-carra-oligosaccharides with DP ranging from 3 to 21 could be obtained with this method, and the structures of the oligosaccharides were consistent with those obtained by traditional mild acid hydrolysis. The new method was more convenient, efficient and environment-friendly than traditional mild acid hydrolysis. Our results provided a useful reference for the preparation of oligosaccharides from other polysaccharides.

  14. Microwave-assisted acid hydrolysis to produce xylooligosaccharides from sugarcane bagasse hemicelluloses.

    PubMed

    Bian, Jing; Peng, Pai; Peng, Feng; Xiao, Xiao; Xu, Feng; Sun, Run-Cang

    2014-08-01

    Hemicelluloses from sugarcane bagasse were subjected to microwave-assisted acid hydrolysis at mild temperature to produce xylooligosaccharides (XOS). The hydrolysis was performed with dilute H2SO4 at 90°C and the influence of acid concentration (0.1-0.3M) and reaction time (20-40min) on the XOS production was ascertained with response surface methodology based on central composite design. The fitted models of XOS and xylose yields were in good agreement with the experimental results. Compared to hydrolysis time, acid concentration was a more significant coefficient in the production of XOS. A well-defined degree of polymerisation of XOS and the monomer in the hydrolysates were quantified. No sugar-degraded byproduct was detected. The maximum XOS yield of 290.2mgg(-1) was achieved by hydrolysis with 0.24M H2SO4 for 31min. The results indicated that the yields of xylose and the byproducts can be controlled by the acid concentration and reaction time in microwave-assisted acid hydrolysis.

  15. Combined heat treatment and acid hydrolysis of cassava grate waste (CGW) biomass for ethanol production

    SciTech Connect

    Agu, R.C.; Amadife, A.E.; Ude, C.M.; Onyia, A.; Ogu, E.O.; Okafor, M.; Ezejiofor, E.

    1997-12-31

    The effect of combined heat treatment and acid hydrolysis (various concentrations) on cassava grate waste (CGW) biomass for ethanol production was investigated. At high concentrations of H{sub 2}SO{sub 4} (1--5 M), hydrolysis of the CGW biomass was achieved but with excessive charring or dehydration reaction. At lower acid concentrations, hydrolysis of CGW biomass was also achieved with 0.3--0.5 M H{sub 2}SO{sub 4}, while partial hydrolysis was obtained below 0.3 M H{sub 2}SO{sub 4} (the lowest acid concentration that hydrolyzed CGW biomass) at 120 C and 1 atm pressure for 30 min. A 60% process efficiency was achieved with 0.3 M H{sub 2}SO{sub 4} in hydrolyzing the cellulose and lignin materials present in the CGW biomass. High acid concentration is therefore not required for CGW biomass hydrolysis. The low acid concentration required for CGW biomass hydrolysis, as well as the minimal cost required for detoxification of CGW biomass because of low hydrogen cyanide content of CGW biomass would seem to make this process very economical. From three liters of the CGW biomass hydrolysate obtained from hydrolysis with 0.3M H{sub 2}SO{sub 4}, ethanol yield was 3.5 (v/v%) after yeast fermentation. However, although the process resulted in gainful utilization of CGW biomass, additional costs would be required to effectively dispose new by-products generated from CGW biomass processing.

  16. Effect of Varying Acid Hydrolysis Condition in Gracilaria Sp. Fermentation Using Sasad

    NASA Astrophysics Data System (ADS)

    Mansuit, H.; Samsuri, M. D. C.; Sipaut, C. S.; Yee, C. F.; Yasir, S. M.; Mansa, R.

    2015-04-01

    Macroalgae or seaweed is being considered as promising feedstock for bioalcohol production due to high polysaccharides content. Polysaccharides can be converted into fermentable sugar through acid hydrolysis pre-treatment. In this study, the potential of using carbohydrate-rich macroalgae, Gracilaria sp. as feedstock for bioalcohol production via various acid hydrolysis conditions prior to the fermentation process was investigated and evaluated. The seaweed used in this research was from the red algae group, using species of Gracilaria sp. which was collected from Sg. Petani Kedah, Malaysia. Pre-treatment of substrate was done using H2SO4 and HCl with molarity ranging from 0.2M to 0.8M. The pretreatment time were varied in the range of 15 to 30 minutes. Fermentation was conducted using Sasad, a local Sabahan fermentation agent as a starter culture. Alcohol extraction was done using a distillation unit. Reducing sugar analysis was done by Benedict test method. Alcohol content analysis was done using specific gravity test. After hydrolysis, it was found out that acid hydrolysis at 0.2M H2SO4 and pre-treated for 20 minutes at 121°C has shown the highest reducing sugar content which has yield (10.06 mg/g) of reducing sugar. It was followed by other samples hydrolysis using 0.4M HCl with 30 minutes pre-treatment and 0.2M H2SO4, 15 minutes pre-treatment with yield of 8.06 mg/g and 5.75 mg/g reducing sugar content respectively. In conclusion, acid hydrolysis of Gracilaria sp. can produce higher reducing sugar yield and thus it can further enhance the bioalcohol production yield. Hence, acid hydrolysis of Gracilaria sp. should be studied more as it is an important step in the bioalcohol production and upscaling process.

  17. Ultrasonic pretreatment and acid hydrolysis of sugarcane bagasse for succinic acid production using Actinobacillus succinogenes.

    PubMed

    Xi, Yong-lan; Dai, Wen-yu; Xu, Rong; Zhang, Jiu-hua; Chen, Ke-quan; Jiang, Min; Wei, Ping; Ouyang, Ping-kai

    2013-11-01

    Immense interest has been devoted to the production of bulk chemicals from lignocellulose biomass. Diluted sulfuric acid treatment is currently one of the main pretreatment methods. However, the low total sugar concentration obtained via such pretreatment limits industrial fermentation systems that use lignocellulosic hydrolysate. Sugarcane bagasse hemicellulose hydrolysate is used as the carbon and nitrogen sources to achieve a green and economical production of succinic acid in this study. Sugarcane bagasse was ultrasonically pretreated for 40 min, with 43.9 g/L total sugar obtained after dilute acid hydrolysis. The total sugar concentration increased by 29.5 %. In a 3-L fermentor, using 30 g/L non-detoxified total sugar as the carbon source, succinic acid production increased to 23.7 g/L with a succinic acid yield of 79.0 % and a productivity of 0.99 g/L/h, and 60 % yeast extract in the medium could be reduced. Compared with the detoxified sugar preparation method, succinic acid production and yield were improved by 20.9 and 20.2 %, respectively. PMID:23649828

  18. Amino acid composition determined using multiple hydrolysis times for three goat milk formulations.

    PubMed

    Rutherfurd, Shane M; Moughan, Paul J; Lowry, Dianne; Prosser, Colin G

    2008-01-01

    The amino acid composition of goat milk formulations with varying protein and carbohydrate concentrations were determined. Proteins in goat milk infant formula, goat milk growing-up formula and goat whole milk powder were hydrolysed using multiple hydrolysis time intervals. A least-squares non-linear regression model was used to predict the free and protein bound amino acid concentrations. The amino acid composition of goat infant formula was compared with human milk reference values. There was good agreement between the multiple hydrolysis and single 24-h hydrolysis methods for approximately one-half of the amino acids. Tryptophan, aspartic acid, threonine, tyrosine, isoleucine, valine, serine and alanine contents were underestimated by 10.6, 5.6, 5.6, 4.7, 4.4, 3.7, 3.7 and 3.6%, respectively, by the single 24-h hydrolysis. The study provides accurate reference data on the amino acid composition of goat milk powders. Goat milk infant formula has amino acids in amounts similar to human milk reference values, when expressed on a per-energy basis.

  19. Evaluation of hyper thermal acid hydrolysis of Kappaphycus alvarezii for enhanced bioethanol production.

    PubMed

    Ra, Chae Hun; Nguyen, Trung Hau; Jeong, Gwi-Taek; Kim, Sung-Koo

    2016-06-01

    Hyper thermal (HT) acid hydrolysis of Kappaphycus alvarezii, a red seaweed, was optimized to 12% (w/v) seaweed slurry content, 180mM H2SO4 at 140°C for 5min. The maximum monosaccharide concentration of 38.3g/L and 66.7% conversion from total fermentable monosaccharides of 57.6g/L with 120gdw/L K. alvarezii slurry were obtained from HT acid hydrolysis and enzymatic saccharification. HT acid hydrolysis at a severity factor of 0.78 efficiently converted the carbohydrates of seaweed to monosaccharides and produced a low concentration of inhibitory compounds. The levels of ethanol production by separate hydrolysis and fermentation with non-adapted and adapted Kluyveromyces marxianus to high concentration of galactose were 6.1g/L with ethanol yield (YEtOH) of 0.19 at 84h and 16.0g/L with YEtOH of 0.42 at 72h, respectively. Development of the HT acid hydrolysis process and adapted yeast could enhance the overall ethanol fermentation yields of K. alvarezii seaweed. PMID:26950757

  20. Efficient production of glucose by microwave-assisted acid hydrolysis of cellulose hydrogel.

    PubMed

    Sun, Binzhe; Duan, Lian; Peng, Gege; Li, Xiaoxia; Xu, Aihua

    2015-09-01

    To improve the production of glucose from cellulose, a simple and effective route was developed. This process uses a combination of a step of cellulose dissolution in aqueous NaOH/urea solution and then regeneration with water, followed by an acid hydrolysis step under microwave irradiation. The method is effective to obtain glucose from α-cellulose, microcrystalline cellulose, filter paper, ramie fiber and absorbent cotton. Increased with the acid concentration the glucose yield from hydrogel hydrolysis increased from 0.42% to 44.6% at 160 °C for 10 min. Moreover, the ozone treatment of cellulose in NaOH/urea solution before regeneration significantly enhanced the hydrolysis efficiency with a glucose yield of 59.1%. It is believed that the chains in cellulose hydrogel are relatively free approached, making that the acids easily access the β-glycosidic bonds.

  1. A Kinetic Study of DDGS Hemicellulose Acid Hydrolysis and NMR Characterization of DDGS Hydrolysate.

    PubMed

    Chen, Hanchi; Liu, Shijie

    2015-09-01

    Liquid hot water (LHW) extraction was used as a pretreatment method to separate the hemicellulose fraction from dried distiller's grain with solubles (DDGS) into liquid phase. Acid hydrolysis using 3.264 % w/w sulfuric acid at 130 °C was performed to convert polysaccharides in LHW extract to monosaccharides. The structure characterization of DDGS in anomeric carbon region based on proton NMR and heteronuclear single quantum coherence (HSQC) during acid hydrolysis was studied in this work. It reveals that the sugar units in DDGS hemicelluloses are constructed with (1-4)-β-D-xylopyranose and α-L-arabinofuranosyl residues. A kinetic model is included to explain the changing concentration of monomer, oligomer, and sugar units. The model was further tested based on the changing concentration of five carbon sugar units during hydrolysis. PMID:26198022

  2. Contribution of acetic acid to the hydrolysis of lignocellulosic biomass under abiotic conditions.

    PubMed

    Trzcinski, Antoine P; Stuckey, David C

    2015-06-01

    Acetic acid was used in abiotic experiments to adjust the solution pH and investigate its influence on the chemical hydrolysis of the Organic Fraction of Municipal Solid Waste (OFMSW). Soluble chemical oxygen demand (SCOD) was used to measure the hydrolysis under oxidative conditions (positive oxidation-reduction potential values), and pH 4 allowed for 20% (±2%) of the COD added to be solubilized, whereas only 12% (±1%) was solubilized at pH7. Under reducing conditions (negative oxidation-reduction potential values) and pH 4, 32.3% (±3%) of the OFMSW was solubilized which shows that acidogenesis at pH 4 during the anaerobic digestion of solid waste can result in chemical hydrolysis. In comparison, bacterial hydrolysis resulted in 54% (±6%) solubilization.

  3. Acid hydrolysis of native corn starch: morphology, crystallinity, rheological and thermal properties.

    PubMed

    Utrilla-Coello, R G; Hernández-Jaimes, C; Carrillo-Navas, H; González, F; Rodríguez, E; Bello-Pérez, L A; Vernon-Carter, E J; Alvarez-Ramirez, J

    2014-03-15

    The acid hydrolysis of native corn starch at 35 °C was monitored during 15 days. After this time, the residual solids were about 37.0 ± 3.0%. First-order kinetics described the hydrolysis data, giving a constant rate of kH = 0.18 ± 0.012 days(-1). Amylose content presented a sharp decrement of about 85% and X-ray diffraction results indicated a gradual increase in crystallinity during the first 3 days. SEM micrographs showed that hydrolysis disrupted granule morphology from an initial regular shape to increasingly irregular shapes. Fractal analysis of SEM images revealed an increase in surface roughness. Fast changes in the thermal effects were caused by molecular rearrangements after fast hydrolysis of amylose in the amorphous regions in the first day. Steady shear rate and oscillatory tests showed a sharp decrease of the apparent viscosity and an increase of the damping factor (tan(δ)) caused by amylose degradation.

  4. Room-Temperature Ferromagnetism in TiO2 Nanocrystals Synthesized by the Controlled Hydrolysis Procedure.

    PubMed

    Gu, Deen; Sun, Zhanhong; Zhou, Lv; Hu, Yongda; Jiang, Yadong

    2016-03-01

    TiO2 nanocrystals were prepared by a controlled hydrolysis procedure at room temperature. The effect of V-doping, N-doping and V/N codoping on the lattice parameters and magnetic properties of TiO2 nanocrystals was investigated by means of X-ray diffraction, high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy and vibration sample magnetometry. Doping performed at room temperature causes the expansion of lattice parameters. Undoped and doped TiO2 nanocrystals show room-temperature ferromagnetism. A monotonic correlation between saturation magnetization and the ratio of the lattice parameter c to a (c/a) was observed. Saturation magnetization of TiO2 nanocrystals increases with the value of c/a.

  5. Acid hydrolysis of Curcuma longa residue for ethanol and lactic acid fermentation.

    PubMed

    Nguyen, Cuong Mai; Nguyen, Thanh Ngoc; Choi, Gyung Ja; Choi, Yong Ho; Jang, Kyoung Soo; Park, Youn-Je; Kim, Jin-Cheol

    2014-01-01

    This research examines the acid hydrolysis of Curcuma longa waste, to obtain the hydrolysate containing lactic acid and ethanol fermentative sugars. A central composite design for describing regression equations of variables was used. The selected optimum condition was 4.91% sulphuric acid, 122.68°C and 50 min using the desirability function under the following conditions: the maximum reducing sugar (RS) yield is within the limited range of the 5-hydroxymethylfurfural (HMF) and furfural concentrations. Under the condition, the obtained solution contained 144 g RS/L, 0.79 g furfural/L and 2.59 g HMF/L and was directly fermented without a detoxification step. The maximum product concentration, average productivity, RS conversion and product yield were 115.36 g/L, 2.88 g/L/h, 89.43% and 64% for L-lactic acid; 113.92 g/L, 2.59 g/L/h, 88.31% and 63.29% for D-lactic acid; and 55.03 g/L, 1.38 g/L/h, 42.66 and 30.57%, respectively, for ethanol using a 7-L jar fermenter.

  6. Acid hydrolysis of Curcuma longa residue for ethanol and lactic acid fermentation.

    PubMed

    Nguyen, Cuong Mai; Nguyen, Thanh Ngoc; Choi, Gyung Ja; Choi, Yong Ho; Jang, Kyoung Soo; Park, Youn-Je; Kim, Jin-Cheol

    2014-01-01

    This research examines the acid hydrolysis of Curcuma longa waste, to obtain the hydrolysate containing lactic acid and ethanol fermentative sugars. A central composite design for describing regression equations of variables was used. The selected optimum condition was 4.91% sulphuric acid, 122.68°C and 50 min using the desirability function under the following conditions: the maximum reducing sugar (RS) yield is within the limited range of the 5-hydroxymethylfurfural (HMF) and furfural concentrations. Under the condition, the obtained solution contained 144 g RS/L, 0.79 g furfural/L and 2.59 g HMF/L and was directly fermented without a detoxification step. The maximum product concentration, average productivity, RS conversion and product yield were 115.36 g/L, 2.88 g/L/h, 89.43% and 64% for L-lactic acid; 113.92 g/L, 2.59 g/L/h, 88.31% and 63.29% for D-lactic acid; and 55.03 g/L, 1.38 g/L/h, 42.66 and 30.57%, respectively, for ethanol using a 7-L jar fermenter. PMID:24240182

  7. Fatty acid specificity of hormone-sensitive lipase. Implication in the selective hydrolysis of triacylglycerols.

    PubMed

    Raclot, T; Holm, C; Langin, D

    2001-12-01

    The selective mobilization of fatty acids from white fat cells depends on their molecular structure, in particular the degree of unsaturation. The present study was designed to examine if the release of fatty acids by hormone-sensitive lipase (HSL) in vitro i) is influenced by the amount of unsaturation, ii) depends on the temperature, and iii) could explain the selective pattern of fatty acid mobilization and notably the preferential mobilization of certain highly unsaturated fatty acids. Recombinant rat and human HSL were incubated with a lipid emulsion. The hydrolysis of 35 individual fatty acids, ranging in chain length from 12 to 24 carbon atoms and in unsaturation from 0 to 6 double bonds was measured. Fatty acid composition of in vitro released NEFA was compared with that of fat cell triacylglycerols (TAG), the ratio % NEFA/% TAG being defined as the relative hydrolysis. The relative hydrolysis of individual fatty acids differed widely, ranging from 0.44 (24:1n-9) to 1.49 (18:1n-7) with rat HSL, and from 0.38 (24:1n-9) to 1.67 (18:1n-7) with human HSL. No major difference was observed between rat and human HSL. The relative release was dependent on the number of double bonds according to chain length. The amount of fatty acid released by recombinant rat HSL was decreased but remained robust at 4 degrees C compared with 37 degrees C, and the relative hydrolysis of some individual fatty acids was affected. The relative hydrolysis of fatty acids moderately, weakly, and highly mobilized by adipose tissue in vivo was similar and close to unity in vitro. We conclude that i) the release of fatty acids by HSL is only slightly affected by their degree of unsaturation, ii) the ability of HSL to efficiently and selectively release fatty acids at low temperature could reflect a cold adaptability for poikilotherms or hibernators when endogenous lipids are needed, and iii) the selectivity of fatty acid hydrolysis by HSL does not fully account for the selective pattern of

  8. Influence of acid precursors on physicochemical properties of nanosized titania synthesized by thermal-hydrolysis method

    SciTech Connect

    Rajesh, B.; Sasirekha, N.R.; Chen, Y.-W.

    2008-03-04

    The influence of nature and concentration of acid species on surface morphology and physicochemical properties of titania particles synthesized by direct thermal hydrolysis of titanium tetrachloride was investigated. The acids used were hydrochloric acid, nitric acid, sulfuric acid, and perchloric acid with a concentration of 3 M. Thermal hydrolysis of titanium tetrachloride in hydrochloric acid and perchloric acid with molar ratios of [H{sup +}]/[Ti{sup 4+}] = 0.5, 1.0, 1.5, and 2.0, respectively, was used to study the effect of acid concentration. The synthesized materials were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, dynamic light scattering, and thermogravimetric analysis. Characterization of the samples by X-ray diffraction studies revealed the influence of acid species on the phase transformation of titania. Samples prepared by hydrochloric acid, nitric acid, and perchloric acid formed rutile phase with rhombus primary particles, while sulfuric acid resulted in anatase phase with flake-shaped primary particles. Transmission electron microscopy and dynamic light scattering results confirmed the nanosized titania particles and the agglomeration of primary particles to form secondary particles in spherical shape. The particle size of titania prepared using perchloric acid was smaller than those prepared with other acid sources. A direct correlation between [H{sup +}]/[Ti{sup 4+}] ratio and particle size of titania was observed.

  9. Hormone-sensitive lipase activity and triacylglycerol hydrolysis are decreased in rat soleus muscle by cyclopiazonic acid.

    PubMed

    Watt, Matthew J; Steinberg, Gregory R; Heigenhauser, G J F; Spriet, Lawrence L; Dyck, David J

    2003-08-01

    Cyclopiazonic acid (CPA) is a sarcoplasmic reticulum Ca2+-ATPase inhibitor that increases intracellular calcium. The role of CPA in regulating the oxidation and esterification of palmitate, the hydrolysis of intramuscular lipids, and the activation of hormone-sensitive lipase (HSL) was examined in isolated rat soleus muscles at rest. CPA (40 micro M) was added to the incubation medium to levels that resulted in subcontraction increases in muscle tension, and lipid metabolism was monitored using the previously described pulse-chase procedure. CPA did not alter the cellular energy state, as reflected by similar muscle contents of ATP, phosphocreatine, free AMP, and free ADP. CPA increased total palmitate uptake into soleus muscle (11%, P < 0.05) and was without effect on palmitate oxidation. This resulted in greater esterification of exogenous palmitate into the triacylglycerol (18%, P < 0.05) and phospholipid (89%, P < 0.05) pools. CPA decreased (P < 0.05) intramuscular lipid hydrolysis, and this occurred as a result of reduced HSL activity (20%, P < 0.05). Incubation of muscles with 3 mM caffeine, which is also known to increase Ca2+ without affecting the cellular energy state, reduced HSL activity (24%, P < 0.05). KN-93, a calcium/calmodulin-dependent kinase inhibitor (CaMKII), blocked the effects of CPA and caffeine, and HSL activity returned to preincubation values. The results of the present study demonstrate that CPA simultaneously decreases intramuscular triacylglycerol (IMTG) hydrolysis and promotes lipid storage in isolated, intact soleus muscle. The decreased IMTG hydrolysis is likely mediated by reduced HSL activity, possibly via the CaMKII pathway. These responses are not consistent with the increased hydrolysis and decreased esterification observed in contracting muscle when substrate availability and the hormonal milieu are tightly controlled. It is possible that more powerful signals or a higher [Ca2+] may override the lipid-storage effect of the CPA

  10. A rapid hydrolysis method and DABS-Cl derivatization for complete amino acid analysis of octreotide acetate by reversed phase HPLC.

    PubMed

    Akhlaghi, Yousef; Ghaffari, Solmaz; Attar, Hossein; Alamir Hoor, Amir

    2015-11-01

    Octreotide as a synthetic cyclic octapeptide is a somatostatin analog with longer half-life and more selectivity for inhibition of the growth hormone. The acetate salt of octreotide is currently used for medical treatment of somatostatin-related disorders such as endocrine and carcinoid tumors, acromegaly, and gigantism. Octreotide contains both cysteine and tryptophan residues which make the hydrolysis part of its amino acid analysis procedure very challenging. The current paper introduces a fast and additive-free method which preserves tryptophan and cysteine residues during the hydrolysis. Using only 6 M HCl, this hydrolysis process is completed in 30 min at 150 °C. This fast hydrolysis method followed by pre-column derivatization of the released amino acids with 4-N,N-dimethylaminoazobenzene-4'-sulfonyl chloride (DABS-Cl) which takes only 20 min, makes it possible to do the complete amino acid analysis of an octreotide sample in a few hours. The highly stable-colored DABS-Cl derivatives can be detected in 436 nm in a reversed phase chromatographic system, which eliminates spectral interferences to a great extent. The amino acid analysis of octreotide acetate including hydrolysis, derivatization, and reversed phase HPLC determination was validated according to International Conference of Harmonization (ICH) guidelines.

  11. A rapid hydrolysis method and DABS-Cl derivatization for complete amino acid analysis of octreotide acetate by reversed phase HPLC.

    PubMed

    Akhlaghi, Yousef; Ghaffari, Solmaz; Attar, Hossein; Alamir Hoor, Amir

    2015-11-01

    Octreotide as a synthetic cyclic octapeptide is a somatostatin analog with longer half-life and more selectivity for inhibition of the growth hormone. The acetate salt of octreotide is currently used for medical treatment of somatostatin-related disorders such as endocrine and carcinoid tumors, acromegaly, and gigantism. Octreotide contains both cysteine and tryptophan residues which make the hydrolysis part of its amino acid analysis procedure very challenging. The current paper introduces a fast and additive-free method which preserves tryptophan and cysteine residues during the hydrolysis. Using only 6 M HCl, this hydrolysis process is completed in 30 min at 150 °C. This fast hydrolysis method followed by pre-column derivatization of the released amino acids with 4-N,N-dimethylaminoazobenzene-4'-sulfonyl chloride (DABS-Cl) which takes only 20 min, makes it possible to do the complete amino acid analysis of an octreotide sample in a few hours. The highly stable-colored DABS-Cl derivatives can be detected in 436 nm in a reversed phase chromatographic system, which eliminates spectral interferences to a great extent. The amino acid analysis of octreotide acetate including hydrolysis, derivatization, and reversed phase HPLC determination was validated according to International Conference of Harmonization (ICH) guidelines. PMID:26002809

  12. Production of fuel ethanol from bamboo by concentrated sulfuric acid hydrolysis followed by continuous ethanol fermentation.

    PubMed

    Sun, Zhao-Yong; Tang, Yue-Qin; Iwanaga, Tomohiro; Sho, Tomohiro; Kida, Kenji

    2011-12-01

    An efficient process for the production of fuel ethanol from bamboo that consisted of hydrolysis with concentrated sulfuric acid, removal of color compounds, separation of acid and sugar, hydrolysis of oligosaccharides and subsequent continuous ethanol fermentation was developed. The highest sugar recovery efficiency was 81.6% when concentrated sulfuric acid hydrolysis was carried out under the optimum conditions. Continuous separation of acid from the saccharified liquid after removal of color compounds with activated carbon was conducted using an improved simulated moving bed (ISMB) system, and 98.4% of sugar and 90.5% of acid were recovered. After oligosaccharide hydrolysis and pH adjustment, the unsterilized saccharified liquid was subjected to continuous ethanol fermentation using Saccharomycescerevisiae strain KF-7. The ethanol concentration, the fermentation yield based on glucose and the ethanol productivity were approximately 27.2 g/l, 92.0% and 8.2 g/l/h, respectively. These results suggest that the process is effective for production of fuel ethanol from bamboo.

  13. Selective hydrolysis of hemicellulose from wheat straw by a nanoscale solid acid catalyst.

    PubMed

    Zhong, Chao; Wang, Chunming; Huang, Fan; Wang, Fengxue; Jia, Honghua; Zhou, Hua; Wei, Ping

    2015-10-20

    A nanoscale catalyst, solid acid SO4(2-)/Fe2O3 with both Lewis and Brønsted acidity was found to effectively hydrolyze hemicellulose while keeping cellulose and lignin inactive, and selective hydrolysis of hemicellulose from wheat straw by this catalyst was also confirmed. The factors that significantly affected hydrolysis process were investigated with response surface methodology, and the optimum conditions for time, temperature, and ratio of wheat straw to catalyst (w/w) were calculated to be 4.10h, 141.97°C, and 1.95:1, respectively. A maximum hemicellulose hydrolysis yield of 63.5% from wheat straw could be obtained under these conditions. In addition, the catalyst could be recycled six times with high activity remaining.

  14. Acid-catalyzed hydrolysis of BMS-582664: degradation product identification and mechanism elucidation.

    PubMed

    Zhao, Fang; Derbin, George; Miller, Scott; Badawy, Sherif; Hussain, Munir

    2012-09-01

    BMS-582664 is an investigational drug intended for cancer treatment through oral administration. The preformulation studies revealed two unexpected degradation products under acidic conditions by reversed-phase high-performance liquid chromatography with ultraviolet detection. Additional liquid chromatography-mass spectrometry results suggested that these were cleavage (hydrolysis) products of a diaryl ether. To further understand the degradation mechanism, the reaction was carried out in (18) O-labeled water. The (18) O was found to be incorporated in only one of the two hydrolysis products. The results suggest that the corresponding α carbon in the heterocycle was unusually eletrophilic in acidic conditions probably because of the protonation of the neighboring nitrogen. This led to the selective attack by water and the consequent hydrolysis products. The study provides a new example of hydrolytic degradation of pharmaceutical compounds, and the reaction center is an aromatic heterocyclic carbon with an aryloxy substitution. PMID:22189636

  15. Dilute acid/metal salt hydrolysis of lignocellulosics

    DOEpatents

    Nguyen, Quang A.; Tucker, Melvin P.

    2002-01-01

    A modified dilute acid method of hydrolyzing the cellulose and hemicellulose in lignocellulosic material under conditions to obtain higher overall fermentable sugar yields than is obtainable using dilute acid alone, comprising: impregnating a lignocellulosic feedstock with a mixture of an amount of aqueous solution of a dilute acid catalyst and a metal salt catalyst sufficient to provide higher overall fermentable sugar yields than is obtainable when hydrolyzing with dilute acid alone; loading the impregnated lignocellulosic feedstock into a reactor and heating for a sufficient period of time to hydrolyze substantially all of the hemicellulose and greater than 45% of the cellulose to water soluble sugars; and recovering the water soluble sugars.

  16. Thermal synthesis and hydrolysis of polyglyceric acid. [in orgin of life studying

    NASA Technical Reports Server (NTRS)

    Weber, Arthur L.

    1989-01-01

    Polyglyceric acid was synthesized by thermal condensation of glyceric acid at 80 C in the presence and absence of two mole percent of sulfuric acid catalyst. The acid catalyst accelerated the polymerization over 100-fold and made possible the synthesis of insoluble polymers of both L- and DL-glyceric acid by heating for less than 1 day. Racemization of L-glyceric acid yielded less than 1 percent D-glyceric acid in condensations carried out at 80 C with catalyst for 1 day and without catalyst for 12 days. The condensation of L-glyceric acid yielded an insoluble polymer much more readily than condensation of DL-glyceric acid. Studies of the hydrolysis of poly-DL-glyceric acid revealed that it was considerably more stable under mild acidic conditions compared to neutral pH. The relationship of this study to the origin of life is discussed.

  17. Reduction in environmental impact of sulfuric acid hydrolysis of bamboo for production of fuel ethanol.

    PubMed

    Sun, Zhao-Yong; Tang, Yue-Qin; Morimura, Shigeru; Kida, Kenji

    2013-01-01

    Fuel ethanol can be produced from bamboo by concentrated sulfuric acid hydrolysis followed by continuous ethanol fermentation. To reduce the environmental impact of this process, treatment of the stillage, reuse of the sulfuric acid and reduction of the process water used were studied. The total organic carbon (TOC) concentration of stillage decreased from 29,688 to 269 mg/l by thermophilic methane fermentation followed by aerobic treatment. Washing the solid residue from acid hydrolysis with effluent from the biological treatment increased the sugar recovery from 69.3% to 79.3%. Sulfuric acid recovered during the acid-sugar separation process was condensed and reused for hydrolysis, resulting in a sugar recovery efficiency of 76.8%, compared to 80.1% when fresh sulfuric acid was used. After acetate removal, the condensate could be reused as elution water in the acid-sugar separation process. As much as 86.3% of the process water and 77.6% of the sulfuric acid could be recycled.

  18. Catalytic conversion of carbohydrates to 5-hydroxymethylfurfural from the waste liquid of acid hydrolysis NCC.

    PubMed

    Sun, Yonghui; Liu, Pengtao; Liu, Zhong

    2016-05-20

    The principal goal of this work was to reuse the carbohydrates and recycle sulfuric acid in the waste liquid of acid hydrolysis nanocrystalline cellulose (NCC). Therefore, in this work, the optimizations of further hydrolysis of waste liquid of acid hydrolysis NCC and catalytic conversion of L4 to 5-hydroxymethylfurfural (5-HMF) were studied. Sulfuric acid was separated by spiral wound diffusion dialysis (SWDD). The results revealed that cellulose can be hydrolyze to glucose absolutely under the condition of temperature 35 °C, 3 h, and sulfuric acid's concentration 62 wt%. And 78.3% sulfuric acid was recovered by SWDD. The yield of 5-HMF was highest in aqueous solution under the optimal condition was as follows, temperature 160 °C, 3 h, and sulfuric acid's concentration 12 wt%. Then the effect of biphasic solvent systems catalytic conversion and inorganic salt as additives were still examined. The results showed that both of them contributed to prepare 5-HMF. The yield and selectivity of 5-HMF was up to 21.0% and 31.4%, respectively.

  19. Oxidation and hydrolysis of lactic acid in near-critical water

    SciTech Connect

    Li, L.; Vallejo, D.; Gloyna, E.F.; Portela, J.R.

    1999-07-01

    Hydrothermal reactions (oxidation and hydrolysis) involving lactic acid (LA) were studied at temperatures ranging from 300 to 400 C and a nominal pressure of 27.6 MPa. Kinetic models were developed with respect to concentrations of LA and total organic carbon (TOC), respectively. On the basis of identified liquid and gaseous products, pathways for hydrothermal reactions involving lactic acid were proposed. Acetic acid and acetaldehyde were confirmed as the major liquid intermediates for oxidation and hydrolysis reactions, respectively. Carbon monoxide and methane were identified as the major gaseous byproducts from these reactions. These results demonstrate the potential of completely oxidizing, as well as converting, lactic acid into other organic products, in high-temperature water.

  20. Enzymatic hydrolysis and fermentation of dilute acid pretreated cornstalk to biohydrogen

    NASA Astrophysics Data System (ADS)

    Pan, C. M.; Fan, Y. T.; Hou, H. W.

    2010-03-01

    The coupling method of acid pretreatment and enzymatic hydrolysis of cornstalk for hydrogen production was investigated in this study. Experimental results showed that temperature, pH and enzyme loading all had an individual significant influence on soluble sugar yield and Ps. The optimum condition for soluble sugar was close to that for Ps. The maximum hydrogen yield from cornstalk by anaerobic mixed microflora was 209.8 ml/g-TVS on the optimum enzymatic hydrolysis condition which was 52 °C of temperature, pH4.8 and 9.4 IU/g of enzyme loading.

  1. Structure and hydrolysis of p-(2-oxo-1-pyrrolidinyl)- benzenesulfonic acid

    SciTech Connect

    Kukalenko, S.S.; Frolov, S.I.; Lim, I.K.; Putsykina, E.B.; Vasil'ev, A.F.

    1987-11-20

    With the aid of vibrational and PMR spectra of p-(2-oso-1-pyrrolidinyl)benzenesulfonic acid it was shown that in the solid state it exists as an O-protonated dipolar ion in which the protonated amide cation and sulfonate ion are intermolecularly linked by a very strong hydrogen bond. In concentrated hydrochloric acid the dipolar ion is an intermediate link in the chain of processes in the hydrolysis of the amide bond of the lactam ring.

  2. Acid hydrolysis of native and annealed starches and branch-structure of their Naegeli dextrins.

    PubMed

    Nakazawa, Yuta; Wang, Ya-Jane

    2003-11-21

    Eight commercial starches, including common corn, waxy corn, wheat, tapioca, potato, Hylon V, Hylon VII, and mung bean starch, were annealed by a multiple-step process, and their gelatinization characteristics were determined. Annealed starches had higher gelatinization temperatures, reduced gelatinization ranges, and increased gelatinization enthalpies than their native starches. The annealed starches with the highest gelatinization enthalpies were subjected to acid hydrolysis with 15.3% H2SO4, and Naegeli dextrins were prepared after 10 days' hydrolysis. Annealing increased the acid susceptibility of native starches in the first (rapid) and the second (slow) phases with potato starch showing the greatest and high amylose starches showing the least changes. Starches with a larger shift in onset gelatinization temperature also displayed a greater percent hydrolysis. The increase in susceptibility to acid hydrolysis was proposed to result from defective and porous structures that resulted after annealing. Although annealing perfected the crystalline structure, it also produced void space, which led to porous structures and possible starch granule defects. The molecular size distribution and chain length distribution of Naegeli dextrins of annealed and native starches were analyzed. The reorganization of the starch molecule during annealing occurred mainly within the crystalline lamellae. Imperfect double helices in the crystalline lamellae improved after annealing, and the branch linkages at the imperfect double helices became protected by the improved crystalline structure. Therefore, more long chains were observed in the Naegeli dextrins of annealed starches than in native starches.

  3. Powerful peracetic acid-ionic liquid pretreatment process for the efficient chemical hydrolysis of lignocellulosic biomass.

    PubMed

    Uju; Goto, Masahiro; Kamiya, Noriho

    2016-08-01

    The aim of this work was to design a new method for the efficient saccharification of lignocellulosic biomass (LB) using a combination of peracetic acid (PAA) pretreatment with ionic liquid (IL)-HCl hydrolysis. The pretreatment of LBs with PAA disrupted the lignin fractions, enhanced the dissolution of LB and led to a significant increase in the initial rate of the IL-HCl hydrolysis. The pretreatment of Bagasse with PAA prior to its 1-buthyl-3-methylimidazolium chloride ([Bmim][Cl])-HCl hydrolysis, led to an improvement in the cellulose conversion from 20% to 70% in 1.5h. Interestingly, the 1-buthyl-3-methylpyridium chloride ([Bmpy][Cl])-HCl hydrolysis of Bagasse gave a cellulose conversion greater than 80%, with or without the PAA pretreatment. For LB derived from seaweed waste, the cellulose conversion reached 98% in 1h. The strong hydrolysis power of [Bmpy][Cl] was attributed to its ability to transform cellulose I to II, and lowering the degree of polymerization of cellulose. PMID:27174616

  4. Fundamental study on kinetics and transport phenomena in low water dilute acid total hydrolysis of cellulosic biomass

    SciTech Connect

    Auburn University

    2004-04-07

    The overall objective of this research is to delineate the process of the dilute-acid hydrolysis of biomass and seek better understanding of the reactions involving dilute-acid treatment of lignocellulosic biomass. Specifically the scope of the work entails the following two primary technical elements: Verification of the heterogeneous nature of the reaction mechanism in dilute-acid hydrolysis of cellulosic component of the biomass. Experimental investigation to identify the overall reaction pattern and the kinetic constants associated with dilute-acid hydrolysis of the cellulosic component of the agricultural residues.

  5. Caffeic acid treatment alters the extracellular adenine nucleotide hydrolysis in platelets and lymphocytes of adult rats.

    PubMed

    Anwar, Javed; Spanevello, Roselia Maria; Pimentel, Victor Camera; Gutierres, Jessié; Thomé, Gustavo; Cardoso, Andreia; Zanini, Daniela; Martins, Caroline; Palma, Heloisa Einloft; Bagatini, Margarete Dulce; Baldissarelli, Jucimara; Schmatz, Roberta; Leal, Cláudio Alberto Martins; da Costa, Pauline; Morsch, Vera Maria; Schetinger, Maria Rosa Chitolina

    2013-06-01

    This study evaluated the effects of caffeic acid on ectonucleotidase activities such as NTPDase (nucleoside triphosphate diphosphohydrolase), Ecto-NPP (nucleotide pyrophosphatase/phosphodiesterase), 5'-nucleotidase and adenosine deaminase (ADA) in platelets and lymphocytes of rats, as well as in the profile of platelet aggregation. Animals were divided into five groups: I (control); II (oil); III (caffeic acid 10 mg/kg); IV (caffeic acid 50 mg/kg); and V (caffeic acid 100 mg/kg). Animals were treated with caffeic acid diluted in oil for 30 days. In platelets, caffeic acid decreased the ATP hydrolysis and increased ADP hydrolysis in groups III, IV and V when compared to control (P<0.05). The 5'-nucleotidase activity was decreased, while E-NPP and ADA activities were increased in platelets of rats of groups III, IV and V (P<0.05). Caffeic acid reduced significantly the platelet aggregation in the animals of groups III, IV and V in relation to group I (P<0.05). In lymphocytes, the NTPDase and ADA activities were increased in all groups treated with caffeic acid when compared to control (P<0.05). These findings demonstrated that the enzymes were altered in tissues by caffeic acid and this compound decreased the platelet aggregation suggesting that caffeic acid should be considered a potentially therapeutic agent in disorders related to the purinergic system.

  6. Monomeric carbohydrates production from olive tree pruning biomass: modeling of dilute acid hydrolysis.

    PubMed

    Puentes, Juan G; Mateo, Soledad; Fonseca, Bruno G; Roberto, Inês C; Sánchez, Sebastián; Moya, Alberto J

    2013-12-01

    Statistical modeling and optimization of dilute sulfuric acid hydrolysis of olive tree pruning biomass has been performed using response surface methodology. Central composite rotatable design was applied to assess the effect of acid concentration, reaction time and temperature on efficiency and selectivity of hemicellulosic monomeric carbohydrates to d-xylose. Second-order polynomial model was fitted to experimental data to find the optimum reaction conditions by multiple regression analysis. The monomeric d-xylose recovery 85% (as predicted by the model) was achieved under optimized hydrolysis conditions (1.27% acid concentration, 96.5°C and 138 min), confirming the high validity of the developed model. The content of d-glucose (8.3%) and monosaccharide degradation products (0.1% furfural and 0.04% 5-hydroxymethylfurfural) provided a high quality subtract, ready for subsequent biochemical conversion to value-added products.

  7. Prediction of acid hydrolysis of lignocellulosic materials in batch and plug flow reactors.

    PubMed

    Jaramillo, Oscar Johnny; Gómez-García, Miguel Ángel; Fontalvo, Javier

    2013-08-01

    This study unifies contradictory conclusions reported in literature on acid hydrolysis of lignocellulosic materials, using batch and plug flow reactors, regarding the influence of the initial liquid ratio of acid aqueous solution to solid lignocellulosic material on sugar yield and concentration. The proposed model takes into account the volume change of the reaction media during the hydrolysis process. An error lower than 8% was found between predictions, using a single set of kinetic parameters for several liquid to solid ratios, and reported experimental data for batch and plug flow reactors. For low liquid-solid ratios, the poor wetting and the acid neutralization, due to the ash presented in the solid, will both reduce the sugar yield. Also, this study shows that both reactors are basically equivalent in terms of the influence of the liquid to solid ratio on xylose and glucose yield.

  8. The effect of acid hydrolysis pretreatment on crystallinity and solubility of kenaf cellulose membrane

    NASA Astrophysics Data System (ADS)

    Saidi, Anis Syuhada Mohd; Zakaria, Sarani; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Padzil, Farah Nadia Mohammad

    2015-09-01

    Cellulose was extracted from kenaf core pulp (KCP) by series of bleaching steps in the sequence (DEED) where D and E are referred as acid and alkali treatment. The bleached kenaf pulp (BKCP) is then pretreated with acid hydrolysis at room temperature for 1 and 3 h respectively. The pretreated cellulose is dissolved in lithium hydroxide/urea (LiOH/urea) and cellulose solution produced was immersed in distilled water bath. BKCP without treatment was also conducted for comparison purpose. The effects of acid hydrolysis pretreatment on solubility and crystallinity are investigated. Higher solubility of cellulose solution is achieved for treated samples. Cellulose II formation and crystallinity index of the cellulose membrane were determined by X-ray diffraction (XRD).

  9. Monomeric carbohydrates production from olive tree pruning biomass: modeling of dilute acid hydrolysis.

    PubMed

    Puentes, Juan G; Mateo, Soledad; Fonseca, Bruno G; Roberto, Inês C; Sánchez, Sebastián; Moya, Alberto J

    2013-12-01

    Statistical modeling and optimization of dilute sulfuric acid hydrolysis of olive tree pruning biomass has been performed using response surface methodology. Central composite rotatable design was applied to assess the effect of acid concentration, reaction time and temperature on efficiency and selectivity of hemicellulosic monomeric carbohydrates to d-xylose. Second-order polynomial model was fitted to experimental data to find the optimum reaction conditions by multiple regression analysis. The monomeric d-xylose recovery 85% (as predicted by the model) was achieved under optimized hydrolysis conditions (1.27% acid concentration, 96.5°C and 138 min), confirming the high validity of the developed model. The content of d-glucose (8.3%) and monosaccharide degradation products (0.1% furfural and 0.04% 5-hydroxymethylfurfural) provided a high quality subtract, ready for subsequent biochemical conversion to value-added products. PMID:24096282

  10. The effect of acid hydrolysis pretreatment on crystallinity and solubility of kenaf cellulose membrane

    SciTech Connect

    Saidi, Anis Syuhada Mohd; Zakaria, Sarani; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Padzil, Farah Nadia Mohammad

    2015-09-25

    Cellulose was extracted from kenaf core pulp (KCP) by series of bleaching steps in the sequence (DEED) where D and E are referred as acid and alkali treatment. The bleached kenaf pulp (BKCP) is then pretreated with acid hydrolysis at room temperature for 1 and 3 h respectively. The pretreated cellulose is dissolved in lithium hydroxide/urea (LiOH/urea) and cellulose solution produced was immersed in distilled water bath. BKCP without treatment was also conducted for comparison purpose. The effects of acid hydrolysis pretreatment on solubility and crystallinity are investigated. Higher solubility of cellulose solution is achieved for treated samples. Cellulose II formation and crystallinity index of the cellulose membrane were determined by X-ray diffraction (XRD)

  11. Prediction of acid hydrolysis of lignocellulosic materials in batch and plug flow reactors.

    PubMed

    Jaramillo, Oscar Johnny; Gómez-García, Miguel Ángel; Fontalvo, Javier

    2013-08-01

    This study unifies contradictory conclusions reported in literature on acid hydrolysis of lignocellulosic materials, using batch and plug flow reactors, regarding the influence of the initial liquid ratio of acid aqueous solution to solid lignocellulosic material on sugar yield and concentration. The proposed model takes into account the volume change of the reaction media during the hydrolysis process. An error lower than 8% was found between predictions, using a single set of kinetic parameters for several liquid to solid ratios, and reported experimental data for batch and plug flow reactors. For low liquid-solid ratios, the poor wetting and the acid neutralization, due to the ash presented in the solid, will both reduce the sugar yield. Also, this study shows that both reactors are basically equivalent in terms of the influence of the liquid to solid ratio on xylose and glucose yield. PMID:23770535

  12. Kinetics of acid hydrolysis and reactivity of some antibacterial hydrophilic iron(II) imino-complexes

    NASA Astrophysics Data System (ADS)

    Shaker, Ali Mohamed; Nassr, Lobna Abdel-Mohsen Ebaid; Adam, Mohamed Shaker Saied; Mohamed, Ibrahim Mohamed Abdelhalim

    2015-05-01

    Kinetic study of acid hydrolysis of some hydrophilic Fe(II) Schiff base amino acid complexes with antibacterial properties was performed using spectrophotometry. The Schiff base ligands were derived from sodium 2-hydroxybenzaldehyde-5-sulfonate and glycine, L-alanine, L-leucine, L-isoleucine, DL-methionine, DL-serine, or L-phenylalanine. The reaction was studied in aqueous media under conditions of pseudo-first order kinetics. Moreover, the acid hydrolysis was studied at different temperatures and the activation parameters were calculated. The general rate equation was suggested as follows: rate = k obs [Complex], where k obs = k 2 [H+]. The evaluated rate constants and activation parameters are consistent with the hydrophilicity of the investigated complexes.

  13. Optimization of wastewater microalgae saccharification using dilute acid hydrolysis for acetone, butanol, and ethanol fermentation

    SciTech Connect

    Castro, Yessica; Ellis, Joshua T.; Miller, Charles D.; Sims, Ronald C.

    2015-02-01

    Exploring and developing sustainable and efficient technologies for biofuel production are crucial for averting global consequences associated with fuel shortages and climate change. Optimization of sugar liberation from wastewater algae through acid hydrolysis was determined for subsequent fermentation to acetone, butanol, and ethanol (ABE) by Clostridium saccharoperbutylacetonicum N1-4. Acid concentration, retention time, and temperature were evaluated to determine optimal hydrolysis conditions by assessing the sugar and ABE yield as well as the associated costs. Sulfuric acid concentrations ranging from 0-1.5 M, retention times of 40-120 min, and temperatures from 23°C- 90°C were combined to form a full factorial experiment. Acid hydrolysis pretreatment of 10% dried wastewater microalgae using 1.0 M sulfuric acid for 120 min at 80-90°C was found to be the optimal parameters, with a sugar yield of 166.1 g for kg of dry algae, concentrations of 5.23 g/L of total ABE, and 3.74 g/L of butanol at a rate of USD $12.83 per kg of butanol.

  14. [Structural characterization of Astragalus polysaccharides using partial acid hydrolysis-hydrophilic interaction liquid chromatography-mass spectrometry].

    PubMed

    Liang, Tu; Fu, Qing; Xin, Huaxia; Li, Fangbing; Jin, Yu; Liang, Xinmiao

    2014-12-01

    Water-soluble polysaccharides from traditional Chinese medicine (TCM) have properties of broad-spectrum treatment and low toxicity, making them as important components in natural medicines and health products. In order to solve the problem of polysaccharides characterization caused by their complex structures, a "bottom-up" approach was developed to complete the characterization of polysaccharides from Astragalus. Firstly, Astragalus pieces were extracted with hot water and then were precipitated by ethanol to obtain Astragalus polysaccharides. Secondly, a partial acid hydrolysis method was carried out and the effects of time, acid concentration and temperature on hydrolysis were investigated. The degree of hydrolysis increased along with the increase of hydrolysis time and acid concentration. The temperature played a great role in the hydrolysis process. No hydrolysis of the polysaccharides occurred at low temperature, while the polysaccharides were almost hydrolyzed to monosaccharide at high temperature. Under the optimum hydrolysis conditions (4 h, 1.5 mol/L trifluoroacetic acid, and 80 °C), Astragalus polysaccharides were hydrolyzed to characteristic oligosaccharide fragments. At last, a hydrophilic liquid chromatography-mass spectrometry method was used for the separation and structural characterization of the polysaccharide hydrolysates. The results showed that the resulting polysaccharides were mainly 1--> 4 linear glucan, and gluco-oligosaccharides with the degrees of polymerization (DP) of 4 - 11 were obtained after partial acid hydrolysis. The significance of this study is that it is the guidance for the characterization of other TCM polysaccharides.

  15. Acid hydrolysis of crude tannins from infructescence of Platycarya strobilacea Sieb. et Zucc to produce ellagic acid.

    PubMed

    Zhang, Liangliang; Wang, Yongmei; Xu, Man

    2014-01-01

    The infructescence of Platycarya strobilacea Sieb. et Zucc is a well-known traditional medicine in China, Japan and Korea. The infructescence of P. strobilacea Sieb. et Zucc is a rich source of ellagitannins that are composed of ellagic acid (EA) and gallic acid, linked to a sugar moiety. The aim of this study was to prepare EA by acid hydrolysis of crude tannins from the infructescence of P. strobilacea Sieb. et Zucc, and establish a new technological processing method for EA. The natural antioxidant EA was prepared by using the water extraction of infructescence of P. strobilacea Sieb. et Zucc, evaporation, condensation, acid hydrolysis and prepared by the process of crystallisation. The yield percentage of EA from crude EA was more than 20% and the purity of the product was more than 98%, as identified by using HPLC. The structure was identified on the basis of spectroscopic analysis and comparison with authentic compound.

  16. Surface Chemical Compositions and Dispersity of Starch Nanocrystals Formed by Sulfuric and Hydrochloric Acid Hydrolysis

    PubMed Central

    Wei, Benxi; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

    2014-01-01

    Surface chemical compositions of starch nanocrystals (SNC) prepared using sulfuric acid (H2SO4) and hydrochloric acid (HCl) hydrolysis were analyzed by X-ray photoelectron spectroscopy (XPS) and FT-IR. The results showed that carboxyl groups and sulfate esters were presented in SNC after hydrolysis with H2SO4, while no sulfate esters were detected in SNC during HCl-hydrolysis. TEM results showed that, compared to H2SO4-hydrolyzed sample, a wider size distribution of SNC prepared by HCl-hydrolysis were observed. Zeta-potentials were −23.1 and −5.02 mV for H2SO4- and HCl-hydrolyzed SNC suspensions at pH 6.5, respectively. Nevertheless, the zeta-potential values decreased to −32.3 and −10.2 mV as the dispersion pH was adjusted to 10.6. After placed 48 h at pH 10.6, zeta-potential increased to −24.1 mV for H2SO4-hydrolyzed SNC, while no change was detected for HCl-hydrolyzed one. The higher zeta-potential and relative small particle distribution of SNC caused more stable suspensions compared to HCl-hydrolyzed sample. PMID:24586246

  17. Surface chemical compositions and dispersity of starch nanocrystals formed by sulfuric and hydrochloric acid hydrolysis.

    PubMed

    Wei, Benxi; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

    2014-01-01

    Surface chemical compositions of starch nanocrystals (SNC) prepared using sulfuric acid (H2SO4) and hydrochloric acid (HCl) hydrolysis were analyzed by X-ray photoelectron spectroscopy (XPS) and FT-IR. The results showed that carboxyl groups and sulfate esters were presented in SNC after hydrolysis with H2SO4, while no sulfate esters were detected in SNC during HCl-hydrolysis. TEM results showed that, compared to H2SO4-hydrolyzed sample, a wider size distribution of SNC prepared by HCl-hydrolysis were observed. Zeta-potentials were -23.1 and -5.02 mV for H2SO4- and HCl-hydrolyzed SNC suspensions at pH 6.5, respectively. Nevertheless, the zeta-potential values decreased to -32.3 and -10.2 mV as the dispersion pH was adjusted to 10.6. After placed 48 h at pH 10.6, zeta-potential increased to -24.1 mV for H2SO4-hydrolyzed SNC, while no change was detected for HCl-hydrolyzed one. The higher zeta-potential and relative small particle distribution of SNC caused more stable suspensions compared to HCl-hydrolyzed sample.

  18. Effects of acid-hydrolysis and hydroxypropylation on functional properties of sago starch.

    PubMed

    Fouladi, Elham; Mohammadi Nafchi, Abdorreza

    2014-07-01

    In this study, sago starch was hydrolyzed by 0.14M HCl for 6, 12, 18, and 24h, and then modified by propylene oxide at a concentration of 0-30% (v/w). The effects of hydrolysis and etherification on molecular weight distribution, physicochemical, rheological, and thermal properties of dually modified starch were estimated. Acid hydrolysis of starch decreased the molecular weight of starch especially amylopectin, but hydroxypropylation had no effect on the molecular weight distribution. The degree of Molar substitution (DS) of hydroxypropylated starch after acid hydrolysis ranged from 0.007 to 0.15. Dually modified starch with a DS higher than 0.1 was completely soluble in cold water at up to 25% concentration of the starch. This study shows that hydroxypropylation and hydrolysis have synergistic effects unlike individual modifications. Dually modified sago starch can be applied to dip-molding for food and pharmaceutical processing because of its high solubility and low tendency for retrogradation.

  19. Dilute acid hydrolysis of wheat straw hemicellulose at moderate temperature: a simplified kinetic model

    SciTech Connect

    Gonzalez, G.; Lopez-Santin, J.; Caminal, G.; Sola, C.

    1986-02-01

    Wheat straw has been hydrolized with sulfuric acid at 34 and 90 degrees C. The treatment at 90 degrees C yields complete solubilization of hemicellulose to xylose and arabinose without significant amounts of furfural. The influence of acid concentration was studied and the kinetics of the acid-catalyzed hydrolysis has been modeled suggesting a two-consecutive reactions mechanism. This model is useful to explain the different behavior of the concentration of the two main sugars produced. The enhanced cellulose accessibility to enzymatic attack is also reported. 26 references.

  20. Comparison of cell wall polysaccharide hydrolysis by a dilute acid/enzymatic saccharification process and rumen microorganisms

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Evaluation of biomass crops for breeding or pricing purposes requires an assay that predicts performance of biomass in the bioenergy conversion process. Cell wall polysaccharide hydrolysis by dilute sulfuric acid pretreatment at 121 degrees C followed by cellulase hydrolysis for 72 h (CONV) and in v...

  1. Nanocellulose prepared by acid hydrolysis of isolated cellulose from sugarcane bagasse

    NASA Astrophysics Data System (ADS)

    Wulandari, W. T.; Rochliadi, A.; Arcana, I. M.

    2016-02-01

    Cellulose in nanometer range or called by nano-cellulose has attracted much attention from researchers because of its unique properties. Nanocellulose can be obtained by acid hydrolysis of cellulose. The cellulose used in this study was isolated from sugarcane bagasse, and then it was hydrolyzed by 50% sulfuric acid at 40 °C for 10 minutes. Nanocellulose has been characterized by Transmission Electron Microscope (TEM), Particle Size Analyzer (PSA), Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray Diffraction (XRD). Analysis of FTIR showed that there were not a new bond which formed during the hydrolysis process. Based on the TEM analysis, nano-cellulose has a spherical morphology with an average diameter of 111 nm and a maximum distribution of 95.9 nm determined by PSA. The XRD analysis showed that the crystallinity degree of nano-cellulose was higher than cellulose in the amount of 76.01%.

  2. Comparison of microwave oven and convection oven for acid hydrolysis of dietary fiber polysaccharides.

    PubMed

    Li, B W

    1998-01-01

    Hydrolysis of dietary fiber polysaccharides (DFP) is an integral part of any enzymatic-chemical method for dietary fiber analysis. Residues obtained after enzyme treatments of fiber-containing foods are usually suspended in 12 M sulfuric acid and kept at or slightly above ambient temperature for at least 1 h, and then the mixtures are diluted with deionized water to a final concentration of 1 M or 2 M acid, followed by heating at 100 degrees C in a water bath or convection oven for 1 or 2 h. Under these hydrolytic conditions, some degradation of the released monosaccharides generally takes place over the duration of hydrolysis. We investigated the feasibility of using microwave energy as a heat source to reduce time and minimize degradation. Preliminary tests were done on the well-characterized soy polysaccharide Fibrim. With a microwave digestion system equipped with temperature and pressure monitors and control lines, optimum settings of power (5%, 75%), time (up to 3 min and 30 s), temperature (35 degrees-55 degrees C), and pressure (45-65 psi) were determined for different foods depending on the residue weight and volume of acid. Results were comparable for microwave oven and convection oven hydrolysis of DFP from 5 foods with good correlations for neutral sugar values; r2 = 0.997 for arabinose, 0.925 for galactose, 0.981 for glucose, 0.969 for mannose, and 0.990 for xylose.

  3. Preparation of crystalline starch nanoparticles using cold acid hydrolysis and ultrasonication.

    PubMed

    Kim, Hee-Young; Park, Dong June; Kim, Jong-Yea; Lim, Seung-Taik

    2013-10-15

    Waxy maize starch in an aqueous sulfuric acid solution (3.16 M, 14.7% solids) was hydrolyzed for 2-6 days, either isothermally at 40 °C or 4 °C, or at cycled temperatures of 4 and 40 °C (1 day each). The starch hydrolyzates were recovered as precipitates after centrifuging the dispersion (10,000 rpm, 10 min). The yield of starch hydrolyzates depended on the hydrolysis temperature and time, which varied from 6.8% to 78%. The starch hydrolyzed at 40 °C or 4/40 °C exhibited increased crystallinity determined by X-ray diffraction analysis, but melted in broader temperature range (from 60 °C to 110 °C). However, the starch hydrolyzed at 4 °C displayed the crystallinity and melting endotherm similar to those of native starch. The starch hydrolyzates recovered by centrifugation were re-dispersed in water (15% solids), and the dispersion was treated by an ultrasonic treatment (60% amplitude, 3min). The ultrasonication effectively fragmented the starch hydrolyzates to nanoparticles. The hydrolyzates obtained after 6 days of hydrolysis were more resistant to the ultrasonication than those after 2 or 4 days, regardless of hydrolysis temperatures. The starch nanoparticles could be prepared with high yield (78%) and crystallinity by 4 °C hydrolysis for 6 days followed by ultrasonication. Scanning electron microscopy revealed that the starch nanoparticles had globular shapes with diameters ranging from 50 to 90 nm.

  4. Acid hydrolysis of native corn starch: morphology, crystallinity, rheological and thermal properties.

    PubMed

    Utrilla-Coello, R G; Hernández-Jaimes, C; Carrillo-Navas, H; González, F; Rodríguez, E; Bello-Pérez, L A; Vernon-Carter, E J; Alvarez-Ramirez, J

    2014-03-15

    The acid hydrolysis of native corn starch at 35 °C was monitored during 15 days. After this time, the residual solids were about 37.0 ± 3.0%. First-order kinetics described the hydrolysis data, giving a constant rate of kH = 0.18 ± 0.012 days(-1). Amylose content presented a sharp decrement of about 85% and X-ray diffraction results indicated a gradual increase in crystallinity during the first 3 days. SEM micrographs showed that hydrolysis disrupted granule morphology from an initial regular shape to increasingly irregular shapes. Fractal analysis of SEM images revealed an increase in surface roughness. Fast changes in the thermal effects were caused by molecular rearrangements after fast hydrolysis of amylose in the amorphous regions in the first day. Steady shear rate and oscillatory tests showed a sharp decrease of the apparent viscosity and an increase of the damping factor (tan(δ)) caused by amylose degradation. PMID:24528771

  5. Morphological characteristics, oxidative stability and enzymic hydrolysis of amylose-fatty acid complexes.

    PubMed

    Marinopoulou, Anna; Papastergiadis, Efthimios; Raphaelides, Stylianos N; Kontominas, Michael G

    2016-05-01

    Complexes of amylose with fatty acids varying in carbon chain length and degree of unsaturation were prepared at 30, 50 or 70°C by dissolving amylose in 0.1N KOH and mixing with fatty acid potassium soap solution. The complexes were obtained in solid form as precipitates after neutralization. SEM microscopy revealed that the morphology of the complexes was that of ordered lamellae separated from amorphous regions whereas confocal laser scanning microscopy showed images of the topography of the guest molecules in the complex matrix. FTIR spectroscopy revealed that the absorption peak attributed to carbonyl group of free fatty acid was shifted when the fatty acid was in the form of amylose complex. Thermo-gravimetry showed that the unsaturated fatty acids were effectively protected from oxidation when they were complexed with amylose whereas enzymic hydrolysis experiments showed that the guest molecules were quantitatively released from the amylose complexes. PMID:26877002

  6. Morphological characteristics, oxidative stability and enzymic hydrolysis of amylose-fatty acid complexes.

    PubMed

    Marinopoulou, Anna; Papastergiadis, Efthimios; Raphaelides, Stylianos N; Kontominas, Michael G

    2016-05-01

    Complexes of amylose with fatty acids varying in carbon chain length and degree of unsaturation were prepared at 30, 50 or 70°C by dissolving amylose in 0.1N KOH and mixing with fatty acid potassium soap solution. The complexes were obtained in solid form as precipitates after neutralization. SEM microscopy revealed that the morphology of the complexes was that of ordered lamellae separated from amorphous regions whereas confocal laser scanning microscopy showed images of the topography of the guest molecules in the complex matrix. FTIR spectroscopy revealed that the absorption peak attributed to carbonyl group of free fatty acid was shifted when the fatty acid was in the form of amylose complex. Thermo-gravimetry showed that the unsaturated fatty acids were effectively protected from oxidation when they were complexed with amylose whereas enzymic hydrolysis experiments showed that the guest molecules were quantitatively released from the amylose complexes.

  7. Process for enzymatic hydrolysis of fatty acid triglycerides with oat caryopses

    SciTech Connect

    Hammond, E.G.; Lee, I.

    1992-02-18

    This patent describes the process for enzymatic hydrolysis of fatty acid triglycerides to obtain free fatty acids and glycerol. It comprises: increasing the water content of dehulled whole oat caryopses to a total water content of 17 to 44% the thus moistened caryopses having active oat lipase associated with the outer surfaces thereof; contacting the moistened whole caryopses with a liquid medium, continuing the contacting until at least 20% by volume of the triglyceride reactant has been hydrolyzed to free fatty acids and glycerol, most of the free fatty acids dissolving in the oil phase external to the caryopses and most of the glycerol being absorbed into the water within the caryopses; and separating the glycerol-containing caryopses from the fatty acid-containing oil phase.

  8. Improved enzymatic hydrolysis of wheat straw by combined use of gamma ray and dilute acid for bioethanol production

    NASA Astrophysics Data System (ADS)

    Hyun Hong, Sung; Taek Lee, Jae; Lee, Sungbeom; Gon Wi, Seung; Ju Cho, Eun; Singh, Sudhir; Sik Lee, Seung; Yeoup Chung, Byung

    2014-01-01

    Pretreating wheat straw with a combination of dilute acid and gamma irradiation was performed in an attempt to enhance the enzymatic hydrolysis for bioethanol production. The glucose yield was significantly affected by combined pretreatment (3% sulfuric acid-gamma irradiation), compared with untreated wheat straw and individual pretreatment. The increasing enzymatic hydrolysis after combined pretreatment is resulting from decrease in crystallinity of cellulose, loss of hemicelluloses, and removal or modification of lignin. Therefore, combined pretreatment is one of the most effective methods for enhancing the enzymatic hydrolysis of wheat straw biomass.

  9. Polylactide stereocomplexation leads to higher hydrolytic stability but more acidic hydrolysis product pattern.

    PubMed

    Andersson, Sofia Regnell; Hakkarainen, Minna; Inkinen, Saara; Södergård, Anders; Albertsson, Ann-Christine

    2010-04-12

    Poly-l-lactide/poly-d-lactide (PLLA/PDLA) stereocomplex had much higher hydrolytic stability compared to plain PLLA, but at the same time shorter and more acidic degradation products were formed. Both materials were subjected to hydrolytic degradation in water and in phosphate buffer at 37 and 60 degrees C, and the degradation processes were monitored by following mass loss, water uptake, thermal properties, surface changes, and pH of the aging medium. The degradation product patterns were determined by electrospray ionization-mass spectrometry (ESI-MS). The high crystallinity and strong secondary interactions in the stereocomplex prevented water uptake and resulted in lower mass loss and degradation rate. However, somewhat surprisingly, the pH of the aging medium decreased much faster in the case of PLLA/PDLA stereocomplex. In accordance, the ESI-MS results showed that hydrolysis of PLLA/PDLA resulted in shorter and more acidic degradation products. This could be explained by the increased intermolecular crystallization due to stereocomplexation, which results in an increased number of tie chains. Because mainly these short tie chains are susceptible to hydrolysis this leads to formation of shorter oligomers compared to hydrolysis of regular PLLA.

  10. Development of C-reactive protein certified reference material NMIJ CRM 6201-b: optimization of a hydrolysis process to improve the accuracy of amino acid analysis.

    PubMed

    Kato, Megumi; Kinumi, Tomoya; Yoshioka, Mariko; Goto, Mari; Fujii, Shin-Ichiro; Takatsu, Akiko

    2015-04-01

    To standardize C-reactive protein (CRP) assays, the National Metrology Institute of Japan (NMIJ) has developed a C-reactive protein solution certified reference material, CRM 6201-b, which is intended for use as a primary reference material to enable the SI-traceable measurement of CRP. This study describes the development process of CRM 6201-b. As a candidate material of the CRM, recombinant human CRP solution was selected because of its higher purity and homogeneity than the purified material from human serum. Gel filtration chromatography was used to examine the homogeneity and stability of the present CRM. The total protein concentration of CRP in the present CRM was determined by amino acid analysis coupled to isotope-dilution mass spectrometry (IDMS-AAA). To improve the accuracy of IDMS-AAA, we optimized the hydrolysis process by examining the effect of parameters such as the volume of protein samples taken for hydrolysis, the procedure of sample preparation prior to the hydrolysis, hydrolysis temperature, and hydrolysis time. Under optimized conditions, we conducted two independent approaches in which the following independent hydrolysis and liquid chromatography-isotope dilution mass spectrometry (LC-IDMS) were combined: one was vapor-phase acid hydrolysis (130 °C, 24 h) and hydrophilic interaction liquid chromatography-mass spectrometry (HILIC-MS) method, and the other was microwave-assisted liquid-phase acid hydrolysis (150 °C, 3 h) and pre-column derivatization liquid chromatography-tandem mass spectrometry (LC-MS/MS) method. The quantitative values of the two different amino acid analyses were in agreement within their uncertainties. The certified value was the weighted mean of the results of the two methods. Uncertainties from the value-assignment method, between-method variance, homogeneity, long-term stability, and short-term stability were taken into account in evaluating the uncertainty for a certified value. The certified value and the

  11. Sulfuric Acid Pretreatment and Enzymatic Hydrolysis of Photoperiod Sensitvie Sorghum for Ethanol Production

    SciTech Connect

    F Xu; Y Shi; X Wu

    2011-12-31

    Photoperiod sensitive (PS) sorghum, with high soluble sugar content, high mass yield and high drought tolerance in dryland environments, has great potential for bioethanol production. The effect of diluted sulfuric acid pretreatment on enzymatic hydrolysis was investigated. Hydrolysis efficiency increased from 78.9 to 94.4% as the acid concentration increased from 0.5 to 1.5%. However, the highest total glucose yield (80.3%) occurred at the 1.0% acid condition because of the significant cellulose degradation at the 1.5% concentration. Synchrotron wide-angle X-ray diffraction was used to study changes of the degree of crystallinity. With comparison of cellulosic crystallinity and adjusted cellulosic crystallinity, the crystalline cellulose decreased after low acidic concentration (0.5%) applied, but did not change significantly, as the acid concentration increased. Scanning electron microscopy was also employed to understand how the morphological structure of PS sorghum changed after pretreatment. Under current processing conditions, the total ethanol yield is 74.5% (about 0.2 g ethanol from 1 g PS sorghum). A detail mass balance was also provided.

  12. Plantain starch granules morphology, crystallinity, structure transition, and size evolution upon acid hydrolysis.

    PubMed

    Hernández-Jaimes, C; Bello-Pérez, L A; Vernon-Carter, E J; Alvarez-Ramirez, J

    2013-06-01

    Plantain native starch was hydrolysed with sulphuric acid for twenty days. Hydrolysis kinetics was described by a logistic function, with a zero-order rate during the first seven days, followed by a slower kinetics dynamics at longer times. X-ray diffraction results revealed a that gradual increase in crystallinity occurred during the first seven days, followed by a decrease to values similar to those found in the native starch. Differential scanning calorimetry analysis suggested a sharp structure transition by the seventh day probably due to a molecular rearrangement of the starch blocklets and inhomogeneous erosion of the amorphous regions and semi crystalline lamellae. Scanning electron micrographs showed that starch granules morphology was continually degraded from an initial oval-like shape to irregular shapes due to aggregation effects. Granule size distribution broadened as hydrolysis time proceeded probably due to fragmentation and agglomeration phenomena of the hydrolysed starch granules.

  13. Value of Coproduction of Ethanol and Furfural from Acid Hydrolysis Processes

    SciTech Connect

    Parker, S.; Calnon, M.; Feinberg, D.; Power, A.; Weiss, L.

    1984-05-01

    In the acid hydrolysis of a cellulosic feedstock (wood, wood wastes, or crop residues), up to 3.65 lb of furfural may be coproduced with each gallon of ethanol for only the cost of recovering and purifying it. Each plant producing 50 x 106 gal/yr of ethanol would produce an amount of by-product furfural equal to the total current domestic production. Thus, the need arises for investigation into potentially suitable processes for deriving profitable end products from furfural and thus expanding the market. The objectives of this study were to determine the economic potential of five selected, large volume derivatives of furfural that could displace hydrocarbon-based chemicals, and the consequent value of furfural as a by-product to the cellulose hydrolysis process of ethanol production.

  14. Alcohol fermentation of sweet potato. 1. Acid hydrolysis and factors involved

    SciTech Connect

    Azhar, A.; Hamdy, M.K.

    1981-04-01

    Factors affecting acid hydrolysis of sweet potato powder (SPP) to fermentable sugars were examined. These include HCl concentration, temperature, time, and levels of SPP. Maximum reducing sugar, reported as dextrose equivalent (DE), was detected after 24 min hydrolysis (1% SPP) in 0.034N HCl heated at 154 degrees celcius. These samples also had 3.43% hydroxymethylfurfural (HMF) based on dry weight. A high level of HMF (9.2%) was detected in 1% SPP heated at 154 degrees C in 0.10N HCl for 18 min. The lowest concentration of HMF formed (1.8%), at maximal DE of 61%, was established in samples containing 5% SPP and heated at 154 degrees C in 0.034N HCl for 48 min. Aqueous extracts of uncured SPP, examined by HPLC, contained glucose, fructose and sucrose, butdegreaded SPP had only glucose and fructose. Products of degraded SPP, under appropriate conditions, could be used for alcohol fermentation. (Refs. 18).

  15. Characterisation of the products from pyrolysis of residues after acid hydrolysis of Miscanthus.

    PubMed

    Melligan, F; Dussan, K; Auccaise, R; Novotny, E H; Leahy, J J; Hayes, M H B; Kwapinski, W

    2012-03-01

    Platform chemicals such as furfural and hydroxymethylfurfural are major products formed during the acid hydrolysis of lignocellulosic biomass in second generation biorefining processes. Solid hydrolysis residues (HR) can amount to 50 wt.% of the starting biomass materials. Pyrolysis of the HRs gives rise to biochar, bio-liquids, and gases. Time and temperature were variables during the pyrolysis of HRs in a fixed bed tubular reactor, and both parameters have major influences on the amounts and properties of the products. Biochar, with potential for carbon sequestration and soil conditioning, composed about half of the HR pyrolysis product. The amounts (11-20 wt.%) and compositions (up to 77% of phenols in organic fraction) of the bio-liquids formed suggest that these have little value as fuels, but could be sources of phenols, and the gas can have application as a fuel. PMID:22281143

  16. Phosphoric acid pretreatment of Achyranthes aspera and Sida acuta weed biomass to improve enzymatic hydrolysis.

    PubMed

    Siripong, Premjet; Duangporn, Premjet; Takata, Eri; Tsutsumi, Yuji

    2016-03-01

    Achyranthes aspera and Sida acuta, two types of weed biomass are abundant and waste in Thailand. We focus on them as novel feedstock for bio-ethanol production because they contain high-cellulose content (45.9% and 46.9%, respectively) and unutilized material. Phosphoric acid (70%, 75%, and 80%) was employed for the pretreatment to improve by enzymatic hydrolysis. The pretreatment process removed most of the xylan and a part of the lignin from the weeds, while most of the glucan remained. The cellulose conversion to glucose was greater for pretreated A. aspera (86.2 ± 0.3%) than that of the pretreated S. acuta (82.2 ± 1.1%). Thus, the removal of hemicellulose significantly affected the efficiency of the enzymatic hydrolysis. The scanning electron microscopy images showed the exposed fibrous cellulose on the cell wall surface, and this substantial change of the surface structure contributed to improving the enzyme accessibility.

  17. A novel prodrug of salicylic acid, salicylic acid-glycylglycine conjugate, utilizing the hydrolysis in rabbit intestinal microorganisms.

    PubMed

    Nakamura, J; Asai, K; Nishida, K; Sasaki, H

    1992-09-01

    The hydrolysis of salicylic acid-glycylglycine conjugate (salicyl-glycylglycine) following oral, intravenous, intracaecal and rectal administration (434, 72, 36 and 36 mumol kg-1, respectively: equivalent to salicylic acid) was examined in rabbits to develop a novel prodrug of salicylic acid. Salicylic acid was detected in the blood 2 h after oral administration of salicyl-glycylglycine and it reached a maximum level (55.6 micrograms mL-1) at 15 h, whereas a small amount of salicyl-glycylglycine was found in the blood. In contrast, unchanged salicyl-glycylglycine was found mainly in the blood following its intravenous administration, suggesting the involvement of presystemic deconjugation in the hydrolysis of salicyl-glycylglycine. Immediate and very extensive salicyclic acid formation in the caecum was observed following intracaecal administration of salicyl-glycylglycine, suggesting that the intestinal microorganisms were responsible for the biotransformation of this compound. In-vitro incubation of salicyl-glycylglycine with caecal content showed that salicyl-glycylglycine was hydrolysed efficiently in the caecum. Consequently, the blood concentration of salicylic acid was prolonged extensively following rectal administration of salicyl-glycylglycine, indicating the usefulness of salicyl-glycylglycine as a prodrug of salicylic acid.

  18. Kinetic study of enzymatic hydrolysis of acid-pretreated coconut coir

    NASA Astrophysics Data System (ADS)

    Fatmawati, Akbarningrum; Agustriyanto, Rudy

    2015-12-01

    Biomass waste utilization for biofuel production such as bioethanol, has become more prominent currently. Coconut coir is one of lignocellulosic food wastes, which is abundant in Indonesia. Bioethanol production from such materials consists of more than one step. Pretreatment and enzymatic hydrolysis is crucial steps to produce sugar which can then be fermented into bioethanol. In this research, ground coconut coir was pretreated using dilute sulfuric acid at 121°C. This pretreatment had increased the cellulose content and decreased the lignin content of coconut coir. The pretreated coconut coir was hydrolyzed using a mix of two commercial cellulase enzymes at pH of 4.8 and temperature of 50°C. The enzymatic hydrolysis was conducted at several initial coconut coir slurry concentrations (0.1-2 g/100 mL) and reaction times (2-72 hours). The reducing sugar concentration profiles had been produced and can be used to obtain reaction rates. The highest reducing sugar concentration obtained was 1,152.567 mg/L, which was produced at initial slurry concentration of 2 g/100 mL and 72 hours reaction time. In this paper, the reducing sugar concentrations were empirically modeled as a function of reaction time using power equations. Michaelis-Menten kinetic model for enzymatic hydrolysis reaction is adopted. The kinetic parameters of that model for sulfuric acid-pretreated coconut coir enzymatic hydrolysis had been obtained which are Vm of 3.587×104 mg/L.h, and KM of 130.6 mg/L.

  19. Improving bioethanol production from olive pruning biomass by deacetylation step prior acid hydrolysis and fermentation processes.

    PubMed

    Moya, Alberto J; Peinado, Silvia; Mateo, Soledad; Fonseca, Bruno G; Sánchez, Sebastián

    2016-11-01

    In order to produce bioethanol from olive tree pruning biomass, deacetylation was performed employing sodium hydroxide. Optimal conditions were determined using experimental design techniques. The highest acetic acid removal (3.8g/dm(3)), obtained by response surface methodology, was at optimum pretreatment conditions of temperature 60°C, 0.8% NaOH and residence time 60min. After oxalic acid hydrolysis of pretreated biomass, the hydrolysates were directly used for ethanol production without further detoxification process. Ethanol yields ranged from 0.19 to 0.45g/g, reaching the maximum yield value when pretreatment was carried out at 130°C with 100mM oxalic acid, involving a combined severity factor (CSF) of 1.05. The highest ethanol concentration obtained from pretreated biomass was 6.2g/dm(3) at 150°C, using 75mM of oxalic acid (CSF=1.53). PMID:27579798

  20. Improving bioethanol production from olive pruning biomass by deacetylation step prior acid hydrolysis and fermentation processes.

    PubMed

    Moya, Alberto J; Peinado, Silvia; Mateo, Soledad; Fonseca, Bruno G; Sánchez, Sebastián

    2016-11-01

    In order to produce bioethanol from olive tree pruning biomass, deacetylation was performed employing sodium hydroxide. Optimal conditions were determined using experimental design techniques. The highest acetic acid removal (3.8g/dm(3)), obtained by response surface methodology, was at optimum pretreatment conditions of temperature 60°C, 0.8% NaOH and residence time 60min. After oxalic acid hydrolysis of pretreated biomass, the hydrolysates were directly used for ethanol production without further detoxification process. Ethanol yields ranged from 0.19 to 0.45g/g, reaching the maximum yield value when pretreatment was carried out at 130°C with 100mM oxalic acid, involving a combined severity factor (CSF) of 1.05. The highest ethanol concentration obtained from pretreated biomass was 6.2g/dm(3) at 150°C, using 75mM of oxalic acid (CSF=1.53).

  1. Modeling Sucrose Hydrolysis in Dilute Sulfuric Acid Solutions at Pretreatment Conditions for Lignocellulosic Biomass

    SciTech Connect

    Bower, S.; Wickramasinghe, R.; Nagle, N. J.; Schell, D. J.

    2008-01-01

    Agricultural and herbaceous feedstocks may contain appreciable levels of sucrose. The goal of this study was to evaluate the survivability of sucrose and its hydrolysis products, fructose and glucose, during dilute sulfuric acid processing at conditions typically used to pretreat lignocellulose biomass. Solutions containing 25 g/l sucrose with 0.1-2.0% (w/w) sulfuric acid concentrations were treated at temperatures of 160-200 C for 3-12 min. Sucrose was observed to completely hydrolyze at all treatment conditions. However, appreciable concentrations of fructose and glucose were detected and glucose was found to be significantly more stable than fructose. Different mathematical approaches were used to fit the kinetic parameters for acid-catalyzed thermal degradation of these sugars. Since both sugars may survive dilute acid pretreatment, they could provide an additional carbon source for production of ethanol and other bio-based products.

  2. The mechanism of hydrothermal hydrolysis for glycyrrhizic acid into glycyrrhetinic acid and glycyrrhetinic acid 3-O-mono-β-D-glucuronide in subcritical water.

    PubMed

    Fan, Rui; Li, Nan; Xu, Honggao; Xiang, Jun; Wang, Lei; Gao, Yanxiang

    2016-01-01

    To improve the bioactivity and sweetness properties of glycyrrhizic acid (GL), the hydrothermal hydrolysis of GL into glycyrrhetinic acid (GA) and glycyrrhetinic acid 3-O-mono-β-D-glucuronide (GAMG) in subcritical water was investigated. The effects of temperature, time and their interaction on the conversion ratios were analyzed and the reactions were elaborated with kinetics and thermodynamics. The results showed that GL hydrothermal hydrolysis was significantly (P < 0.05) affected by reaction time and temperature, as well as their interaction, and could be fitted into first-order kinetics. The thermodynamic analysis indicated that the hydrolysis of GL was endergonic and non-spontaneous. The hydrolytic pathways were composed of complex consecutive and parallel reactions. It was concluded that subcritical water may be a potential medium for producing GAMG and GA.

  3. A novel diffusion-biphasic hydrolysis coupled kinetic model for dilute sulfuric acid pretreatment of corn stover.

    PubMed

    Chen, Longjian; Zhang, Haiyan; Li, Junbao; Lu, Minsheng; Guo, Xiaomiao; Han, Lujia

    2015-02-01

    Kinetic experiments on the dilute sulfuric acid pretreatment of corn stover were performed. A high xylan removal and a low inhibitor concentration were achieved by acid pretreatment. A novel diffusion-hydrolysis coupled kinetic model was proposed. The contribution to the xylose yield was analyzed by the kinetic model. Compared with the inhibitor furfural negatively affecting xylose yield, the fast and slow-hydrolyzing xylan significantly contributed to the xylose yield, however, their dominant roles were dependent on reaction temperature and time. The impact of particle size and acid concentration on the xylose yield were also investigated. The diffusion process may significantly influence the hydrolysis of large particles. Increasing the acid concentration from 0.15 M to 0.30 M significantly improved the xylose yield, whereas the extent of improvement decreased to near-quantitative when further increasing acid loading. These findings shed some light on the mechanism for dilute sulfuric acid hydrolysis of corn stover.

  4. Elucidating the structure of cyclotides by partial acid hydrolysis and LC-MS/MS analysis.

    PubMed

    Sze, Siu Kwan; Wang, Wei; Meng, Wei; Yuan, Randong; Guo, Tiannan; Zhu, Yi; Tam, James P

    2009-02-01

    We describe here a rapid method to determine the cyclic structure and disulfide linkages of highly stable cyclotides via a combination of flash partial acid hydrolysis, LC-MS/MS, and computational tools. Briefly, a mixture of closely related cyclotides, kalata B1 and varv A purified from Viola yedoensis was partially hydrolyzed in 2 M HCl for 5 min by microwave-assisted hydrolysis or for 30 min in an autoclave oven (121 degrees C and 15 psi). The partially hydrolyzed peptide mixture was then subjected to LC-MS/MS analysis, with the disulfide linked-peptides fragmented by collision activated dissociation (CAD). A computer program written in-house (available for download at http://proteomics.sbs.ntu.edu.sg/cyclotide_SS ) was used for interpreting LC-MS/MS spectra and assigning the disulfide bonds. Time-point analysis of single-disulfide fragments revealed that nonrandom acid catalyzed fragmentation mostly occurred at the turns which are solvent-exposed and often contain side chain functionalized amino acids such as Asx/Glx and Ser/Thr. In particular, the most susceptible bond for acid hydrolysis in kalata B1 and varv A was found to be the highly conserved N25-G26 which is also the head-to-tail ligation site of the linear precursor proteins, indicating that formation of the three disulfide bonds might precede cyclic structure closure by N25-G26 ligation. This observation is consistent with the recent report that the N25-G26 bond formation is the last step in the cyclotide biosynthetic pathway. The process demonstrated here can potentially be a high throughput method that is generally applicable to determine disulfide bonds of other relatively low-abundance cyclotides.

  5. Heteropoly Acid/Nitrogen Functionalized Onion-like Carbon Hybrid Catalyst for Ester Hydrolysis Reactions.

    PubMed

    Liu, Wei; Qi, Wei; Guo, Xiaoling; Su, Dangsheng

    2016-02-18

    A novel heteropoly acid (HPA)/nitrogen functionalized onion-like carbon (NOLC) hybrid catalyst was synthesized through supramolecular (electrostatic and hydrogen bond) interactions between the two components. The chemical structure and acid strength of the HPA/NOLC hybrid have been fully characterized by thermogravimetric analysis, IR spectroscopy, X-ray photoelectron spectroscopy, NH3 temperature-programmed desorption and acid-base titration measurements. The proposed method for the fabrication of the HPA/NOLC hybrid catalyst is a universal strategy for different types of HPAs to meet various requirements of acidic or redox catalysis. The hydrophobic environment of NOLC effectively prevents the deactivation of HPA in an aqueous system, and the combination of uniformly dispersed HPA clusters and the synergistic effect between NOLC and HPA significantly promotes its activity in ester hydrolysis reactions, which is higher than that of bare PWA as homogeneous catalyst. The kinetics of the hydrolysis reactions indicate that the aggregation status of the catalyst particles has great influence on the apparent activity. PMID:26606266

  6. Heteropoly Acid/Nitrogen Functionalized Onion-like Carbon Hybrid Catalyst for Ester Hydrolysis Reactions.

    PubMed

    Liu, Wei; Qi, Wei; Guo, Xiaoling; Su, Dangsheng

    2016-02-18

    A novel heteropoly acid (HPA)/nitrogen functionalized onion-like carbon (NOLC) hybrid catalyst was synthesized through supramolecular (electrostatic and hydrogen bond) interactions between the two components. The chemical structure and acid strength of the HPA/NOLC hybrid have been fully characterized by thermogravimetric analysis, IR spectroscopy, X-ray photoelectron spectroscopy, NH3 temperature-programmed desorption and acid-base titration measurements. The proposed method for the fabrication of the HPA/NOLC hybrid catalyst is a universal strategy for different types of HPAs to meet various requirements of acidic or redox catalysis. The hydrophobic environment of NOLC effectively prevents the deactivation of HPA in an aqueous system, and the combination of uniformly dispersed HPA clusters and the synergistic effect between NOLC and HPA significantly promotes its activity in ester hydrolysis reactions, which is higher than that of bare PWA as homogeneous catalyst. The kinetics of the hydrolysis reactions indicate that the aggregation status of the catalyst particles has great influence on the apparent activity.

  7. Effects of dilute acid pretreatment conditions on enzymatic hydrolysis monomer and oligomer sugar yields for aspen, balsam, and switchgrass.

    PubMed

    Jensen, Jill R; Morinelly, Juan E; Gossen, Kelsey R; Brodeur-Campbell, Michael J; Shonnard, David R

    2010-04-01

    The effects of dilute acid hydrolysis conditions were investigated on total sugar (glucose and xylose) yields after enzymatic hydrolysis with additional analyses on glucose and xylose monomer and oligomer yields from the individual hydrolysis steps for aspen (a hardwood), balsam (a softwood), and switchgrass (a herbaceous energy crop). The results of this study, in the form of measured versus theoretical yields and a severity analysis, show that for aspen and balsam, high dilute acid hydrolysis xylose yields were obtainable at all acid concentrations (0.25-0.75 wt.%) and temperatures (150-175 degrees C) studied as long as reaction time was optimized. Switchgrass shows a relatively stronger dependence on dilute acid hydrolysis acid concentration due to its higher neutralizing mineral content. Maximum total sugar (xylose and glucose; monomer plus oligomer) yields post-enzymatic hydrolysis for aspen, balsam, and switchgrass, were 88.3%, 21.2%, and 97.6%, respectively. In general, highest yields of total sugars (xylose and glucose; monomer plus oligomer) were achieved at combined severity parameter values (log CS) between 2.20 and 2.40 for the biomass species studied.

  8. Effect of ultrasonic pre-treatment on low temperature acid hydrolysis of oil palm empty fruit bunch.

    PubMed

    Yunus, Robiah; Salleh, Shanti Faridah; Abdullah, Nurhafizah; Biak, Dyg Radiah Awg

    2010-12-01

    Various pre-treatment techniques change the physical and chemical structure of the lignocellulosic biomass and improve hydrolysis rates. The effect of ultrasonic pre-treatment on oil palm empty fruit bunch (OPEFB) fibre prior to acid hydrolysis has been evaluated. The main objective of this study was to determine if ultrasonic pre-treatment could function as a pre-treatment method for the acid hydrolysis of OPEFB fibre at a low temperature and pressure. Hydrolysis at a low temperature was studied using 2% sulphuric acid; 1:25 solid liquid ratio and 100 degrees C operating temperature. A maximum xylose yield of 58% was achieved when the OPEFB fibre was ultrasonicated at 90% amplitude for 45min. In the absence of ultrasonic pre-treatment only 22% of xylose was obtained. However, no substantial increase of xylose formation was observed for acid hydrolysis at higher temperatures of 120 and 140 degrees C on ultrasonicated OPEFB fibre. The samples were then analysed using a scanning electron microscope (SEM) to describe the morphological changes of the OPEFB fibre. The SEM observations show interesting morphological changes within the OPEFB fibre for different acid hydrolysis conditions. PMID:20719502

  9. Optimization of the Hydrolysis of Safflower Oil for the Production of Linoleic Acid, Used as Flavor Precursor

    PubMed Central

    Aziz, Marya; Husson, Florence; Kermasha, Selim

    2015-01-01

    Commercial lipases, from porcine pancreas (PPL), Candida rugosa (CRL), and Thermomyces lanuginosus (Lipozyme TL IM), were investigated in terms of their efficiency for the hydrolysis of safflower oil (SO) for the liberation of free linoleic acid (LA), used as a flavor precursor. Although PPL, under the optimized conditions, showed a high degree of hydrolysis (91.6%), its low tolerance towards higher substrate concentrations could limit its use for SO hydrolysis. In comparison to the other investigated lipases, Lipozyme TL IM required higher amount of enzyme and an additional 3 h of reaction time to achieve its maximum degree of SO hydrolysis (90.2%). On the basis of the experimental findings, CRL was selected as the most appropriate biocatalyst, with 84.1% degree of hydrolysis. The chromatographic analyses showed that the CRL-hydrolyzed SO is composed mainly of free LA. PMID:26904663

  10. Optimization of the Hydrolysis of Safflower Oil for the Production of Linoleic Acid, Used as Flavor Precursor.

    PubMed

    Aziz, Marya; Husson, Florence; Kermasha, Selim

    2015-01-01

    Commercial lipases, from porcine pancreas (PPL), Candida rugosa (CRL), and Thermomyces lanuginosus (Lipozyme TL IM), were investigated in terms of their efficiency for the hydrolysis of safflower oil (SO) for the liberation of free linoleic acid (LA), used as a flavor precursor. Although PPL, under the optimized conditions, showed a high degree of hydrolysis (91.6%), its low tolerance towards higher substrate concentrations could limit its use for SO hydrolysis. In comparison to the other investigated lipases, Lipozyme TL IM required higher amount of enzyme and an additional 3 h of reaction time to achieve its maximum degree of SO hydrolysis (90.2%). On the basis of the experimental findings, CRL was selected as the most appropriate biocatalyst, with 84.1% degree of hydrolysis. The chromatographic analyses showed that the CRL-hydrolyzed SO is composed mainly of free LA. PMID:26904663

  11. Effect of citric acid concentration and hydrolysis time on physicochemical properties of sweet potato starches.

    PubMed

    Surendra Babu, Ayenampudi; Parimalavalli, Ramanathan; Rudra, Shalini Gaur

    2015-09-01

    Physicochemical properties of citric acid treated sweet potato starches were investigated in the present study. Sweet potato starch was hydrolyzed using citric acid with different concentrations (1 and 5%) and time periods (1 and 11 h) at 45 °C and was denoted as citric acid treated starch (CTS1 to CTS4) based on their experimental conditions. The recovery yield of acid treated starches was above 85%. The CTS4 sample displayed the highest amylose (around 31%) and water holding capacity its melting temperature was 47.66 °C. The digestibility rate was slightly increased for 78.58% for the CTS3 and CTS4. The gel strength of acid modified starches ranged from 0.27 kg to 1.11 kg. RVA results of acid thinned starches confirmed a low viscosity profile. CTS3 starch illustrated lower enthalpy compared to all other modified starches. All starch samples exhibited a shear-thinning behavior. SEM analysis revealed that the extent of visible degradation was increased at higher hydrolysis time and acid concentration. The CTS3 satisfied the criteria required for starch to act as a fat mimetic. Overall results conveyed that the citric acid treatment of sweet potato starch with 5% acid concentration and 11h period was an ideal condition for the preparation of a fat replacer.

  12. Glycosyl conformational and inductive effects on the acid catalysed hydrolysis of purine nucleosides.

    PubMed Central

    Jordan, F; Niv, H

    1977-01-01

    The log kobs vs. pH profiles were determined in the intermediate acidity region for the glycosyl hydrolysis of guanosine and its 8-amino, 8-monomethylamino, 8-dimethylamino and 8-bromo derivatives. The decreased rate of the 8-amino and enhanced rate of the 8-bromo compound compared to guanosine support an A type mechanism: base protonation followed by glycosyl bond cleavage. All three 8-amino guanosines exhibited log kobs - pH profiles clearly showing that both mono and di-base protonated nucleosides undergo hydrolysis. The 700 fold rate acceleration of 8-N(CH3)-guanosine compared to 8-NHCH3-guanosine and the 110 fold rate acceleration of 8-N(CH3)2-adenosine compared to 8-NHCH3-adenosine could be unequivocally attributed to the fixed syn glycosyl conformation of both 8-dimethylamino compounds and relief of steric compression upon hydrolysis in these molecules. The lack of anomerization of all substrates during the course of the reaction supports an A rather than a Schiff-base mechanism. PMID:17100

  13. Housefly larvae hydrolysate: orthogonal optimization of hydrolysis, antioxidant activity, amino acid composition and functional properties

    PubMed Central

    2013-01-01

    Background Antioxidant, one of the most important food additives, is widely used in food industry. At present, antioxidant is mostly produced by chemical synthesis, which would accumulate to be pathogenic. Therefore, a great interest has been developed to identify and use natural antioxidants. It was showed that there are a lot of antioxidative peptides in protein hydrolysates, possessing strong capacity of inhibiting peroxidation of macro-biomolecular and scavenging free redicals in vivo. Enzymatic hydrolysis used for preparation of antioxidative peptides is a new hot-spot in the field of natural antioxidants. It reacts under mild conditions, with accurate site-specific degradation, good repeatability and few damages to biological activity of protein. Substrates for enzymatic hydrolysis are usually plants and aqua-animals. Insects are also gaining attention because of their rich protein and resource. Antioxidative peptides are potential to be exploited as new natural antioxidant and functional food. There is a huge potential market in medical and cosmetic field as well. Result Protein hydrolysate with antioxidant activity was prepared from housefly larvae, by a two-step hydrolysis. Through orthogonal optimization of the hydrolysis conditions, the degree of hydrolysis was determined to be approximately 60%. Fractionated hydrolysate at 25 mg/mL, 2.5 mg/mL and 1 mg/mL exhibited approximately 50%, 60% and 50% of scavenging capacity on superoxide radicals, 1, 1-Diphenyl-2-picrylhydrazyl radicals and hydroxyl radicals, respectively. Hydrolysate did not exhibit substantial ion chelation. Using a linoneic peroxidation system, the inhibition activity of hydrolysate at 20 mg/mL was close to that of 20 μg/mL tertiary butylhydroquinone, suggesting a potential application of hydrolysate in the oil industry as an efficient antioxidant. The lyophilized hydrolysate presented almost 100% solubility at pH 3-pH 9, and maintained nearly 100% activity at pH 5-pH 8 at 0

  14. Microwave-assisted acid and base hydrolysis of intact proteins containing disulfide bonds for protein sequence analysis by mass spectrometry.

    PubMed

    Reiz, Bela; Li, Liang

    2010-09-01

    Controlled hydrolysis of proteins to generate peptide ladders combined with mass spectrometric analysis of the resultant peptides can be used for protein sequencing. In this paper, two methods of improving the microwave-assisted protein hydrolysis process are described to enable rapid sequencing of proteins containing disulfide bonds and increase sequence coverage, respectively. It was demonstrated that proteins containing disulfide bonds could be sequenced by MS analysis by first performing hydrolysis for less than 2 min, followed by 1 h of reduction to release the peptides originally linked by disulfide bonds. It was shown that a strong base could be used as a catalyst for microwave-assisted protein hydrolysis, producing complementary sequence information to that generated by microwave-assisted acid hydrolysis. However, using either acid or base hydrolysis, amide bond breakages in small regions of the polypeptide chains of the model proteins (e.g., cytochrome c and lysozyme) were not detected. Dynamic light scattering measurement of the proteins solubilized in an acid or base indicated that protein-protein interaction or aggregation was not the cause of the failure to hydrolyze certain amide bonds. It was speculated that there were some unknown local structures that might play a role in preventing an acid or base from reacting with the peptide bonds therein.

  15. Hydrolysis of Selected Tropical Plant Wastes Catalyzed by a Magnetic Carbonaceous Acid with Microwave.

    PubMed

    Su, Tong-Chao; Fang, Zhen; Zhang, Fan; Luo, Jia; Li, Xing-Kang

    2015-01-01

    In this study, magnetic carbonaceous acids were synthesized by pyrolysis of the homogeneous mixtures of glucose and magnetic Fe3O4 nanoparticles, and subsequent sulfonation. The synthesis conditions were optimized to obtain a catalyst with both high acid density (0.75 mmol g(-1)) and strong magnetism [magnetic saturation, Ms = 19.5 Am(2) kg(-1)]. The screened catalyst (C-SO3H/Fe3O4) was used to hydrolyze ball-milled cellulose in a microwave reactor with total reducing sugar (TRS) yield of 25.3% under the best conditions at 190 °C for 3.5 h. It was cycled for at least seven times with high catalyst recovery rate (92.8%), acid density (0.63 mmol g(-1)) and magnetism (Ms = 12.9 Am(2) kg(-1)), as well as high TRS yield (20.1%) from the hydrolysis of ball-milled cellulose. The catalyst was further successfully tested for the hydrolysis of tropical biomass with high TRS and glucose yields of 79.8% and 58.3% for bagasse, 47.2% and 35.6% for Jatropha hulls, as well as 54.4% and 35.8% for Plukenetia hulls. PMID:26648414

  16. Production of xylose from Meranti wood sawdust by dilute acid hydrolysis.

    PubMed

    Rafiqul, I S M; Sakinah, A M M; Karim, M R

    2014-09-01

    Xylitol production by bioconversion of xylose can be economically interesting if the raw material can be recovered from a cheap lignocellulosic biomass (LCB). Meranti wood sawdust (MWS) is a renewable and low-cost LCB that can be used as a promising and economic source of xylose, a starting raw material for the manufacture of several specialty chemicals, especially xylitol. This study aimed to optimize the hydrolysis process of MWS and to determine the influence of temperature, H2SO4 concentration, and residence time on xylose release and on by-product formation (glucose, arabinose, acetic acid, furfural, hydroxymethylfurfural (HMF), and lignin degradation products (LDPs)). Batch hydrolysis was conducted under various operating conditions, and response surface methodology was adopted to achieve the highest xylose yield. Xylose production was highly affected by temperature, acid concentration, and residence time. The optimum temperature, acid concentration, and time were determined to be 124 °C, 3.26 %, and 80 min, respectively. Under these optimum conditions, xylose yield and selectivity were attained at 90.6 % and 4.05 g/g, respectively.

  17. Effect of acid concentration and pulp properties on hydrolysis reactions of mercerized sisal.

    PubMed

    Lacerda, Talita M; Zambon, Márcia D; Frollini, Elisabete

    2013-03-01

    The influence of sulfuric acid concentration (H2SO4 5-25%, 100°C), crystallinity and fibers size on the hydrolysis reaction of sisal pulps were investigated, with the goal of evaluating both the liquor composition, as an important step in the production of bioethanol, and the residual non-hydrolyzed pulp, to determine its potential application as materials. Aliquots were withdrawn from the reaction media, and the liquor composition was analyzed by HPLC. The residual non-hydrolyzed pulps were characterized by SEM, their average molar mass and crystallinity index, and their size distribution was determined using a fiber analyzer. Sulfuric acid 25% led to the highest glucose content (approximately 10gL(-1)), and this acid concentration was chosen to evaluate the influence of both the fiber size and crystallinity of the starting pulp on hydrolysis. The results showed that fibers with higher length and lower crystallinity favored glucose production in approximately 12%, with respect to the highly crystalline shorter fibers. PMID:23465940

  18. Hydrolysis of Selected Tropical Plant Wastes Catalyzed by a Magnetic Carbonaceous Acid with Microwave

    NASA Astrophysics Data System (ADS)

    Su, Tong-Chao; Fang, Zhen; Zhang, Fan; Luo, Jia; Li, Xing-Kang

    2015-12-01

    In this study, magnetic carbonaceous acids were synthesized by pyrolysis of the homogeneous mixtures of glucose and magnetic Fe3O4 nanoparticles, and subsequent sulfonation. The synthesis conditions were optimized to obtain a catalyst with both high acid density (0.75 mmol g-1) and strong magnetism [magnetic saturation, Ms = 19.5 Am2 kg-1]. The screened catalyst (C-SO3H/Fe3O4) was used to hydrolyze ball-milled cellulose in a microwave reactor with total reducing sugar (TRS) yield of 25.3% under the best conditions at 190 °C for 3.5 h. It was cycled for at least seven times with high catalyst recovery rate (92.8%), acid density (0.63 mmol g-1) and magnetism (Ms = 12.9 Am2 kg-1), as well as high TRS yield (20.1%) from the hydrolysis of ball-milled cellulose. The catalyst was further successfully tested for the hydrolysis of tropical biomass with high TRS and glucose yields of 79.8% and 58.3% for bagasse, 47.2% and 35.6% for Jatropha hulls, as well as 54.4% and 35.8% for Plukenetia hulls.

  19. Hydrolysis of Selected Tropical Plant Wastes Catalyzed by a Magnetic Carbonaceous Acid with Microwave

    PubMed Central

    Su, Tong-Chao; Fang, Zhen; Zhang, Fan; Luo, Jia; Li, Xing-Kang

    2015-01-01

    In this study, magnetic carbonaceous acids were synthesized by pyrolysis of the homogeneous mixtures of glucose and magnetic Fe3O4 nanoparticles, and subsequent sulfonation. The synthesis conditions were optimized to obtain a catalyst with both high acid density (0.75 mmol g−1) and strong magnetism [magnetic saturation, Ms = 19.5 Am2 kg−1]. The screened catalyst (C-SO3H/Fe3O4) was used to hydrolyze ball-milled cellulose in a microwave reactor with total reducing sugar (TRS) yield of 25.3% under the best conditions at 190 °C for 3.5 h. It was cycled for at least seven times with high catalyst recovery rate (92.8%), acid density (0.63 mmol g−1) and magnetism (Ms = 12.9 Am2 kg−1), as well as high TRS yield (20.1%) from the hydrolysis of ball-milled cellulose. The catalyst was further successfully tested for the hydrolysis of tropical biomass with high TRS and glucose yields of 79.8% and 58.3% for bagasse, 47.2% and 35.6% for Jatropha hulls, as well as 54.4% and 35.8% for Plukenetia hulls. PMID:26648414

  20. Preparation and evaluation of lignosulfonates as a dispersant for gypsum paste from acid hydrolysis lignin.

    PubMed

    Matsushita, Yasuyuki; Yasuda, Seiichi

    2005-03-01

    In order to effectively utilize a by-product of the acid saccharification process of woody materials, the chemical conversion of guaiacyl sulfuric acid lignin (SAL), one of the acid hydrolysis lignins, into water-soluble sulfonated products with high dispersibitity was investigated. At first, SAL was phenolated (P-SAL) to enhance the solubility and reactivity. Lignosulfonates were prepared from P-SAL by three methods of hydroxymethylation followed by neutral sulfonation (two-step method), sulfomethylation (one-step method) and arylsulfonation. Surprisingly, all prepared lignosulfonates possessed 30 to 70% higher dispersibility for gypsum paste than the commercial lignosulfonate. Evaluation of the preparations for gypsum paste suggested that the higher molecular weights and sulfur contents of the preparations increased their dispersibility. PMID:15491828

  1. Preparation and evaluation of lignosulfonates as a dispersant for gypsum paste from acid hydrolysis lignin.

    PubMed

    Matsushita, Yasuyuki; Yasuda, Seiichi

    2005-03-01

    In order to effectively utilize a by-product of the acid saccharification process of woody materials, the chemical conversion of guaiacyl sulfuric acid lignin (SAL), one of the acid hydrolysis lignins, into water-soluble sulfonated products with high dispersibitity was investigated. At first, SAL was phenolated (P-SAL) to enhance the solubility and reactivity. Lignosulfonates were prepared from P-SAL by three methods of hydroxymethylation followed by neutral sulfonation (two-step method), sulfomethylation (one-step method) and arylsulfonation. Surprisingly, all prepared lignosulfonates possessed 30 to 70% higher dispersibility for gypsum paste than the commercial lignosulfonate. Evaluation of the preparations for gypsum paste suggested that the higher molecular weights and sulfur contents of the preparations increased their dispersibility.

  2. Extraction of cellulose nano-crystals from old corrugated container fiber using phosphoric acid and enzymatic hydrolysis followed by sonication.

    PubMed

    Tang, Yanjun; Shen, Xiaochuang; Zhang, Junhua; Guo, Daliang; Kong, Fangong; Zhang, Nan

    2015-07-10

    Due to its amazing physicochemical properties and high environmental compatibility, cellulose nano-crystals (CNC) hold great promise for serving as a strategic platform for sustainable development. Now, there has been growing interest in the development of processes using waste or residual biomass as CNC source for addressing economic and environmental concerns. In the present work, a combined process involving phosphoric acid hydrolysis, enzymatic hydrolysis and sonication was proposed aiming to efficiently exact CNC from low-cost old corrugated container (OCC) pulp fiber. The effect of enzymatic hydrolysis on the yield and microstructure of resulting CNC was highlighted. Results showed that the enzymatic hydrolysis was effective in enhancing CNC yield after phosphoric acid hydrolysis. CNC was obtained with a yield of 23.98 wt% via the combined process with phosphoric acid concentration of 60 wt%, cellulase dosage of 2 mL (84 EGU) per 2g fiber and sonication intensity of 200 W. Moreover, the presence of enzymatic hydrolysis imparted the obtained CNC with improved dispersion, increased crystallinity and thermal stability.

  3. Kinetic characterization for dilute sulfuric acid hydrolysis of timber varieties and switchgrass.

    PubMed

    Yat, Shu Chiang; Berger, Alan; Shonnard, David R

    2008-06-01

    Hydrolysis of four timber species (aspen, balsam fir, basswood, and red maple) and switchgrass was studied using dilute sulfuric acid at 50 g dry biomass/L under similar conditions previously described as acid pretreatment. The primary goal was to obtain detailed kinetic data of xylose formation and degradation from a match between a first order reaction model and the experimental data at various final reactor temperatures (160-190 degrees C), sulfuric acid concentrations (0.25-1.0% w/v), and particle sizes (28-10/20 mesh) in a glass-lined 1L well-mixed batch reactor. Reaction rates for the generation of xylose from hemicellulose and the generation of furfural from xylose were strongly dependent on both temperature and acid concentration. However, no effect was observed for the particle sizes studied. Oligomer sugars, representing incomplete products of hydrolysis, were observed early in the reaction period for all sugars (xylose, glucose, arabinose, mannose, and galactose), but were reduced to low concentrations at later times (higher hemicellulose conversions). Maximum yields for xylose ranged from 70% (balsam) to 94% (switchgrass), for glucose from 10.6% to 13.6%, and for other minor sugars from 8.6% to 58.9%. Xylose formation activation energies and the pre-exponential factors for the timber species and switchgrass were in a range of 49-180 kJ/mol and from 7.5 x 10(4) to 2.6 x 10(20)min(-1), respectively. In addition, for xylose degradation, the activation energies and the pre-exponential factors ranged from 130 to 170 kJ/mol and from 6.8 x 10(13) to 3.7 x 10(17)min(-1), respectively. There was a near linear dependence on acid concentration observed for xylose degradation. Our results suggest that mixtures of biomass species may be processed together and still achieve high yields for all species. PMID:17904838

  4. A new effective process for production of curdlan oligosaccharides based on alkali-neutralization treatment and acid hydrolysis of curdlan particles in water suspension.

    PubMed

    Li, Jing; Zhu, Li; Zheng, Zhi-Yong; Zhan, Xiao-Bei; Lin, Chi-Chung; Zong, Yu; Li, Wei-Jiang

    2013-10-01

    Biologically active β-1,3-oligosaccharides with rapidly growing biomedical applications are produced from hydrolysis of curdlan polysaccharide. The water-insoluble curdlan impedes its hydrolysis efficiency which is enhanced by our newly developed alkali-neutralization treatment process to increase the stability of curdlan suspension to more than 20 days, while the untreated control settled within 5 min. A putative double-layer structure model comprising of a compact core and a hydrated outer layer was proposed to describe the treated curdlan particles based on sedimentation and scanning electron microscopy observation. This model was verified by single- and two-step acid hydrolysis, indicative of the reduced susceptibility to hydrolysis when close to the compact core. Electrospray ionization-mass spectrometry, thin-layer chromatography analyses, and effective HPLC procedure led to the development of improved process to produce purified individual β-1,3-oligosaccharides with degrees of polymerization from 2 to 10 and potential for biomedical applications from curdlan hydrolyzate. Our new curdlan oligosaccharide production process offers an even better alternative to the previously published processes.

  5. Hydrolysis of microcrystalline cellulose using functionalized Bronsted acidic ionic liquids - A comparative study.

    PubMed

    Parveen, Firdaus; Patra, Tanmoy; Upadhyayula, Sreedevi

    2016-01-01

    Cellulose conversion to platform chemicals is required to meet the demands of increasing population and modernization of the world. Hydrolysis of microcrystalline cellulose was studied with SO3H, COOH and OH functionalized imidazole based ionic liquid using 1-butyl-3-methylimidazolium chloride [BMIM]Cl as a solvent. The influence of temperature, time, acidity of ionic liquids and catalyst loading was studied on hydrolysis reaction. The maximum %TRS yield 85%, was obtained at 100°C and 90min with 0.2g of SO3H functionalized ionic liquid. UV-vis spectroscopy using 4-nitro aniline as an indicator was performed to find out the Hammett function of ionic liquid and acidity trends are as follows: SO3H>COOH>OH. Density functional theory (DFT) calculations were performed to optimize the ionic liquid and their conjugate bases at B3LYP 6-311G++ (d, p) level using Gaussian 09 program. Theoretical findings are in agreement with the experimental results.

  6. Synthesis, hydrolysis, and skin retention of amino acid esters of alpha-tocopherol.

    PubMed

    Marra, Fabio; Ostacolo, Carmine; Laneri, Sonia; Bernardi, Antonietta; Sacchi, Antonia; Padula, Cristina; Nicoli, Sara; Santi, Patrizia

    2009-07-01

    The aim of this work was to synthesize new pro-vitamins of alpha-tocopherol (VE) able to release another moiety such as an amino acid, in order to obtain a combined antioxidant and moisturizing effect upon topical application. The new derivatives were characterized and tested for sensitivity to chemical and enzymatic hydrolysis. Lipophilicity was estimated using Log capacity factor and skin retention was determined in vitro, using rabbit ear skin as barrier. Five molecules were synthesized using L-proline, L-serine, L-tyrosine, L-asparagine, and L-citrulline as amino acidic moiety. All pro-vitamins showed similar or lower lipophilicity than alpha-tocopheryl acetate (VEAc), taken as reference, and similar stability in aqueous solutions. All pro-vitamins showed to be sensitive to enzymatic hydrolysis. None of the pro-vitamins crossed the skin in significant amounts, whereas they accumulated into the skin, in both the dermis and the epidermis. They are more hydrophilic and more water-soluble than the currently used acetate.

  7. Ultrasonic enhance acid hydrolysis selectivity of cellulose with HCl-FeCl3 as catalyst.

    PubMed

    Li, Jinbao; Zhang, Xiangrong; Zhang, Meiyun; Xiu, Huijuan; He, Hang

    2015-03-01

    The effect of ultrasonic pretreatment coupled with HCl-FeCl3 catalyst was evaluated to hydrolyze cellulose amorphous regions. The ultrasonic pretreatment leads to cavitation that affects the morphology and microstructure of fibers, enhancing the accessibility of chemical reagent to the loosened amorphous regions of cellulose. In this work, Fourier transform infrared spectroscopy (FTIR) was used to identify characteristic absorption bands of the constituents and the crystallinity was evaluated by the X-ray diffraction (XRD) technique. The results indicated that appropriate ultrasonic pretreatment assisted with FeCl3 can enhance the acid hydrolysis of amorphous regions of cellulose, thus improving the crystallinity of the remaining hydrocellulose. It was observed that sonication samples that were pretreated for 300 W and 20 min followed by acid hydrolysis had maximum of 78.9% crystallinity. The crystallinity was 9.2% higher than samples that were not subjected to ultrasound. In addition, the average fines length decreased from 49 μm to 37 μm. PMID:25498717

  8. Alkaline pretreatment methods followed by acid hydrolysis of Saccharum spontaneum for bioethanol production.

    PubMed

    Chaudhary, Gaurav; Singh, Lalit Kumar; Ghosh, Sanjoy

    2012-11-01

    Different alkaline pretreatment methods (NaOH, NaOH+10% urea and aqueous ammonia) were optimized for maximum delignification of Saccharum spontaneum at 30°C. Maximum delignification were obtained as 47.8%, 51% and 48% from NaOH (7% NaOH, 48h, and 10% biomass loading), NaOH+urea (7% NaOH+10% urea, 48 h and 10% biomass loading) and 30% ammonia (40 days and 10% biomass loading) respectively. H(2)SO(4) 60% (v/v), 10% biomass loading at 30°C for 4h, were optimized conditions to solubilize the cellulose and hemicellulose from solid residue obtained after different optimized alkaline pretreatments. Slurry thus obtained was diluted to obtain final acid concentration of 10% (v/v) for real hydrolysis of cellulose and hemicellulose at 100°C for 1h. Among all pretreatment methods applied, the best result 0.58 g (85%) reducing sugars/g of initial biomass after acid hydrolysis was obtained from aqueous ammonia pretreated biomass. Scheffersomyces stipitis CBS6054 was used to ferment the hydrolysate; ethanol yield (Y(p/s)) and productivity (r(p)) were found to be 0.35 g/g and 0.22 g/L/h respectively.

  9. Assessment on proximate composition, dietary fiber, phytic acid and protein hydrolysis of germinated Ecuatorian brown rice.

    PubMed

    Cáceres, Patricio J; Martínez-Villaluenga, Cristina; Amigo, Lourdes; Frias, Juana

    2014-09-01

    Germinated brown rice (GBR) is considered healthier than brown rice (BR) but its nutritive value has been hardly studied. Since nutritive quality of GBR depends on genetic diversity and germination conditions, six Ecuadorian BR varieties were germinated at 28 and 34 ºC for 48 and 96 h in darkness and proximate composition, dietary fiber fractions, phytic acid content as well as degree of protein hydrolysis and peptide content were studied. Protein, lipids, ash and available carbohydrate ranged 7.3-10.4%, 2.0-4.0%, 0.8-1.5% and 71.6 to 84.0%, respectively, in GBR seedlings. Total dietary fiber increased during germination (6.1-13.6%), with a large proportion of insoluble fraction, while phytic acid was reduced noticeably. In general, protein hydrolysis occurred during germination was more accused at 28 ºC for 48 h. These results suggest that GBR can be consumed directly as nutritive staple food for a large population worldwide contributing to their nutritional requirements.

  10. Hydrolysis optimization and characterization study of preparing fatty acids from Jatropha curcas seed oil

    PubMed Central

    2011-01-01

    Background Fatty acids (FAs) are important as raw materials for the biotechnology industry. Existing methods of FAs production are based on chemical methods. In this study potassium hydroxide (KOH)-catalyzed reactions were utilized to hydrolysis Jatropha curcas seed oil. Results The parameters effect of ethanolic KOH concentration, reaction temperature, and reaction time to free fatty acid (FFA%) were investigated using D-Optimal Design. Characterization of the product has been studied using Fourier transforms infrared spectroscopy (FTIR), gas chromatography (GC) and high performance liquid chromatography (HPLC). The optimum conditions for maximum FFA% were achieved at 1.75M of ethanolic KOH concentration, 65°C of reaction temperature and 2.0 h of reaction time. Conclusions This study showed that ethanolic KOH concentration was significant variable for J. curcas seed oil hydrolysis. In a 18-point experimental design, FFA% of hydrolyzed J. curcas seed oil can be raised from 1.89% to 102.2%, which proved by FTIR and HPLC. PMID:22044685

  11. Ferrihydrite dissolution by pyridine-2,6-bis(monothiocarboxylic acid) and hydrolysis products

    NASA Astrophysics Data System (ADS)

    Dhungana, Suraj; Anthony, Charles R.; Hersman, Larry E.

    2007-12-01

    Pyridine-2,6-bis(monothiocarboxylate) (pdtc), a metabolic product of microorganisms, including Pseudomonas putida and Pseudomonas stutzeri was investigated for its ability of dissolve Fe(III)(hydr)oxides at pH 7.5. Concentration dependent dissolution of ferrihydrite under anaerobic environment showed saturation of the dissolution rate at the higher concentration of pdtc. The surface controlled ferrihydrite dissolution rate was determined to be 1.2 × 10 -6 mol m -2 h -1. Anaerobic dissolution of ferrihydrite by pyridine-2,6-dicarboxylic acid or dipicolinic acid (dpa), a hydrolysis product of pdtc, was investigated to study the mechanism(s) involved in the pdtc facilitated ferrihydrite dissolution. These studies suggest that pdtc dissolved ferrihydrite using a reduction step, where dpa chelates the Fe reduced by a second hydrolysis product, H 2S. Dpa facilitated dissolution of ferrihydrite showed very small increase in the Fe dissolution when the concentration of external reductant, ascorbate, was doubled, suggesting the surface dynamics being dominated by the interactions between dpa and ferrihydrite. Greater than stoichiometric amounts of Fe were mobilized during dpa dissolution of ferrihydrite assisted by ascorbate and cysteine. This is attributed to the catalytic dissolution of Fe(III)(hydr)oxides by the in situ generated Fe(II) in the presence of a complex former, dpa.

  12. Effect of acid hydrolysis and fungal biotreatment on agro-industrial wastes for obtainment of free sugars for bioethanol production

    PubMed Central

    El-Tayeb, T.S.; Abdelhafez, A.A.; Ali, S.H.; Ramadan, E.M.

    2012-01-01

    This study was designed to evaluate selected chemical and microbiological treatments for the conversion of certain local agro-industrial wastes (rice straw, corn stalks, sawdust, sugar beet waste and sugarcane bagasse) to ethanol. The chemical composition of these feedstocks was determined. Conversion of wastes to free sugars by acid hydrolysis varied from one treatment to another. In single-stage dilute acid hydrolysis, increasing acid concentration from 1 % (v/v) to 5 % (v/v) decreased the conversion percentage of almost all treated agro-industrial wastes. Lower conversion percentages for some treatments were obtained when increasing the residence time from 90 to 120 min. The two-stage dilute acid hydrolysis by phosphoric acid (1.0 % v/v) followed by sulphuric acid (1.0 % v/v) resulted in the highest conversion percentage (41.3 % w/w) on treated sugar beet waste. This treatment when neutralized, amended with some nutrients and inoculated with baker’s yeast, achieved the highest ethanol concentration (1.0 % v/v). Formation of furfural and hydroxymethylfurfural (HMF) were functions of type of acid hydrolysis, acid concentration, residence time and feedstock type. The highest bioconversion of 5 % wastes (37.8 % w/w) was recorded on sugar beet waste by Trichoderma viride EMCC 107. This treatment when followed by baker’s yeast fermentation, 0.41 % (v/v) ethanol and 8.2 % (v/w) conversion coefficient were obtained. PMID:24031984

  13. Effect of acid hydrolysis and fungal biotreatment on agro-industrial wastes for obtainment of free sugars for bioethanol production.

    PubMed

    El-Tayeb, T S; Abdelhafez, A A; Ali, S H; Ramadan, E M

    2012-10-01

    This study was designed to evaluate selected chemical and microbiological treatments for the conversion of certain local agro-industrial wastes (rice straw, corn stalks, sawdust, sugar beet waste and sugarcane bagasse) to ethanol. The chemical composition of these feedstocks was determined. Conversion of wastes to free sugars by acid hydrolysis varied from one treatment to another. In single-stage dilute acid hydrolysis, increasing acid concentration from 1 % (v/v) to 5 % (v/v) decreased the conversion percentage of almost all treated agro-industrial wastes. Lower conversion percentages for some treatments were obtained when increasing the residence time from 90 to 120 min. The two-stage dilute acid hydrolysis by phosphoric acid (1.0 % v/v) followed by sulphuric acid (1.0 % v/v) resulted in the highest conversion percentage (41.3 % w/w) on treated sugar beet waste. This treatment when neutralized, amended with some nutrients and inoculated with baker's yeast, achieved the highest ethanol concentration (1.0 % v/v). Formation of furfural and hydroxymethylfurfural (HMF) were functions of type of acid hydrolysis, acid concentration, residence time and feedstock type. The highest bioconversion of 5 % wastes (37.8 % w/w) was recorded on sugar beet waste by Trichoderma viride EMCC 107. This treatment when followed by baker's yeast fermentation, 0.41 % (v/v) ethanol and 8.2 % (v/w) conversion coefficient were obtained. PMID:24031984

  14. Theoretical study of the alkaline hydrolysis of an aza-β-lactam derivative of clavulanic acid

    NASA Astrophysics Data System (ADS)

    Garcías, Rafael C.; Coll, Miguel; Donoso, Josefa; Muñoz, Francisco

    2003-04-01

    DFT calculations based on the hybrid functional B3LYP/6-31+G * were used to study the alkaline hydrolysis of an aza-clavulanic acid, which results from the substitution of the carbon atom at position 6 in clavulanic acid by a nitrogen atom. The presence of the nitrogen atom endows the compound with special properties; in fact, once formed, the tetrahedral intermediate can evolve with cleavage of the N 4-C 7 or N 6-C 7 bond, which obviously leads to different reaction products. These differential bond cleavages may play a central role in the inactivation of β-lactamases, so the compound may be a powerful inactivator of these enzymes.

  15. Preparation of highly charged cellulose nanofibrils using high-pressure homogenization coupled with strong acid hydrolysis pretreatments.

    PubMed

    Tian, Cuihua; Yi, Jianan; Wu, Yiqiang; Wu, Qinglin; Qing, Yan; Wang, Lijun

    2016-01-20

    Cellulose nanofibrils (CNFs) are attracting much attention for the advantages of excellent mechanical strength, good optical transparency, and high surface area. An eco-friendly and energy-saving method was created in this work to produce highly negative charged CNFs using high-pressure mechanical defibrillation coupled with strong acid hydrolysis pretreatments. The morphological development, zeta potential, crystal structure, chemical composition and thermal degradation behavior of the resultant materials were evaluated by transmission electron microscopy (TEM), zeta potential analysis, X-ray diffraction (XRD), Fourier transform infrared spectrometry (FTIR), and thermogravimetric analysis (TGA). These CNFs were fully separated, surface-charged, and highly entangled. They showed a large fiber aspect ratio compared to traditional cellulose nanocrystrals that are produced by strong acid hydrolysis. Compared to hydrochloric acid hydrolysis, the CNFs produced by sulfuric acid pretreatments were completely defibrillated and presented stable suspensions (or gels) even at low fiber content. On the other hand, CNFs pretreated by hydrochloric acid hydrolysis trended to aggregate because of the absence of surface charge. The crystallinity index (CI) of CNFs decreased because of mechanical defibrillation, and then increased dramatically with increased sulfuric acid concentration and reaction time. FTIR analysis showed that the C-O-SO3 group was introduced on the surfaces of CNFs during sulfuric acid hydrolysis. These sulfate groups accelerated the thermal degradation of CNFs, which occurred at lower temperature than wood pulp, indicating that the thermal stability of sulfuric acid hydrolyzed CNFs was decreased. The temperature of the maximum decomposition rate (Tmax) and the maximum weight-loss rates (MWLRmax) were much lower than for wood pulp because of the retardant effect of sulfuric acid during the combustion of CNFs. By contrast, the CNFs treated with hydrochloric acid

  16. Clay ingestion enhances intestinal triacylglycerol hydrolysis and non-esterified fatty acid absorption.

    PubMed

    Habold, Caroline; Reichardt, François; Le Maho, Yvon; Angel, Fabielle; Liewig, Nicole; Lignot, Jean-Hervé; Oudart, Hugues

    2009-07-01

    Consumption by animals and humans of earthy materials such as clay is often related to gut pathologies. Our aim was to determine the impact of kaolinite ingestion on glucose and NEFA transport through the intestinal mucosa. The expression of hexose transporters (Na/glucose co-transporter 1 (SGLT1), GLUT2, GLUT5) and of proteins involved in NEFA absorption (fatty acid transporter/cluster of differentiation 36 (FAT/CD36), fatty acid transport protein 4 (FATP4) and liver fatty acid binding protein (L-FABP)) was measured (1) in rats whose jejunum was perfused with a solution of kaolinite, and (2) in rats who ate spontaneously kaolinite pellets during 7 and 28 d. Also, we determined TAG and glucose absorption in the kaolinite-perfused group, and pancreatic lipase activity, gastric emptying and intestinal transit in rats orally administered with kaolinite. Glucose absorption was not affected by kaolinite perfusion or ingestion. However, kaolinite induced a significant increase in intestinal TAG hydrolysis and NEFA absorption. The cytoplasmic expression of L-FABP and FATP4 also increased due to kaolinite ingestion. NEFA may enter the enterocytes via endocytosis mainly since expression of NEFA transporters in the brush-border membrane was not affected by kaolinite. After uptake, rapid binding of NEFA by L-FABP and FATP4 could act as an intracellular NEFA buffer to prevent NEFA efflux. Increased TAG hydrolysis and NEFA absorption may be due to the adsorption properties of clay and also because kaolinite ingestion caused a slowing down of gastric emptying and intestinal transit.

  17. Alcohol fermentation of sweet potato - 1. Acid hydrolysis and factors involved

    SciTech Connect

    Azhar, A.; Hamdy, M.K.

    1981-04-01

    Factors affecting acid hydrolysis of sweet potato powder (SPP) to fermentable sugars were examined. These include HCl concentration, temperature, time, and levels of SPP. Maximum reducing sugar, reported as dextrose equivalent (DE), was detected after 24 min hydrolysis (1% SPP) in 0.034N HCl heated at 154/degree/C. These samples also had 3.43% hydroxymethylfurfural (HMF) based on dry weight. A high level of HMF (9.2%) was detected in 1% SPP heated at 154/degree/C in 0.10N HCl for 18 min. The lowest concentration of HMF formed (1.8%), at maximal DE of 61%, was established in samples containing 5% SPP and heated at 154/degree/C in 0.034N HCl for 48 min. Aqueous extracts of uncured SPP, examined by High Performance Liquid Chromatography, contained glucose, fructose and sucrose, but degraded SPP had only glucose and fructose. Products of degraded SPP, Under appropriate conditions, could be used for alcohol fermentation. 18 refs.

  18. Strategies to achieve high-solids enzymatic hydrolysis of dilute-acid pretreated corn stover.

    PubMed

    Geng, Wenhui; Jin, Yongcan; Jameel, Hasan; Park, Sunkyu

    2015-01-01

    Three strategies were presented to achieve high solids loading while maximizing carbohydrate conversion, which are fed-batch, splitting/thickening, and clarifier processes. Enzymatic hydrolysis was performed at water insoluble solids (WIS) of 15% using washed dilute-acid pretreated corn stover. The carbohydrate concentration increased from 31.8 to 99.3g/L when the insoluble solids content increased from 5% to 15% WIS, while the final carbohydrate conversion was decreased from 78.4% to 73.2%. For the fed-batch process, a carbohydrate conversion efficiency of 76.8% was achieved when solid was split into 60:20:20 ratio, with all enzymes added first. For the splitting/thickening process, a carbohydrate conversion of 76.5% was realized when the filtrate was recycled to simulate a steady-state process. Lastly, the clarifier process was evaluated and the highest carbohydrate conversion of 81.4% was achieved. All of these results suggests the possibility of enzymatic hydrolysis at high solids to make the overall conversion cost-competitive.

  19. Economic impact of total solids loading on enzymatic hydrolysis of dilute acid pretreated corn stover.

    PubMed

    Humbird, David; Mohagheghi, Ali; Dowe, Nancy; Schell, Daniel J

    2010-01-01

    In process integration studies of the biomass-to-ethanol conversion process, it is necessary to understand how cellulose conversion yields vary as a function of solids and enzyme loading and other key operating variables. The impact of solids loading on enzymatic cellulose hydrolysis of dilute acid pretreated corn stover slurry was determined using an experimental response surface design methodology. From the experimental work, an empirical correlation was obtained that expresses monomeric glucose yield from enzymatic cellulose hydrolysis as a function of solids loading, enzyme loading, and temperature. This correlation was used in a technoeconomic model to study the impact of solids loading on ethanol production economics. The empirical correlation was used to provide a more realistic assessment of process cost by accounting for changes in cellulose conversion yields at different solids and enzyme loadings as well as enzyme cost. As long as enzymatic cellulose conversion drops off at higher total solids loading (due to end-product inhibition or other factors), there is an optimum value for the total solids loading that minimizes the ethanol production cost. The optimum total solids loading shifts to higher values as enzyme cost decreases.

  20. Enantioselective Hydrolysis of Amino Acid Esters Promoted by Bis(β-cyclodextrin) Copper Complexes.

    PubMed

    Xue, Shan-Shan; Zhao, Meng; Ke, Zhuo-Feng; Cheng, Bei-Chen; Su, Hua; Cao, Qian; Cao, Zhen-Kun; Wang, Jun; Ji, Liang-Nian; Mao, Zong-Wan

    2016-02-26

    It is challenging to create artificial catalysts that approach enzymes with regard to catalytic efficiency and selectivity. The enantioselective catalysis ranks the privileged characteristic of enzymatic transformations. Here, we report two pyridine-linked bis(β-cyclodextrin) (bisCD) copper(II) complexes that enantioselectively hydrolyse chiral esters. Hydrolytic kinetic resolution of three pairs of amino acid ester enantiomers (S1-S3) at neutral pH indicated that the "back-to-back" bisCD complex CuL(1) favoured higher catalytic efficiency and more pronounced enantioselectivity than the "face-to-face" complex CuL(2). The best enantioselectivity was observed for N-Boc-phenylalanine 4-nitrophenyl ester (S2) enantiomers promoted by CuL(1), which exhibited an enantiomer selectivity of 15.7. We observed preferential hydrolysis of L-S2 by CuL(1), even in racemic S2, through chiral high-performance liquid chromatography (HPLC). We demonstrated that the enantioselective hydrolysis was related to the cooperative roles of the intramolecular flanking chiral CD cavities with the coordinated copper ion, according to the results of electrospray ionization mass spectrometry (ESI-MS), inhibition experiments, rotating-frame nuclear Overhauser effect spectroscopy (ROESY), and theoretical calculations. Although the catalytic parameters lag behind the level of enzymatic transformation, this study confirms the cooperative effect of the first and second coordination spheres of artificial catalysts in enantioselectivity and provides hints that may guide future explorations of enzyme mimics.

  1. Methane production from acid hydrolysates of Agave tequilana bagasse: evaluation of hydrolysis conditions and methane yield.

    PubMed

    Arreola-Vargas, Jorge; Ojeda-Castillo, Valeria; Snell-Castro, Raúl; Corona-González, Rosa Isela; Alatriste-Mondragón, Felipe; Méndez-Acosta, Hugo O

    2015-04-01

    Evaluation of diluted acid hydrolysis for sugar extraction from cooked and uncooked Agave tequilana bagasse and feasibility of using the hydrolysates as substrate for methane production, with and without nutrient addition, in anaerobic sequencing batch reactors (AnSBR) were studied. Results showed that the hydrolysis over the cooked bagasse was more effective for sugar extraction at the studied conditions. Total sugars concentration in the cooked and uncooked bagasse hydrolysates were 27.9 g/L and 18.7 g/L, respectively. However, 5-hydroxymethylfurfural was detected in the cooked bagasse hydrolysate, and therefore, the uncooked bagasse hydrolysate was selected as substrate for methane production. Interestingly, results showed that the AnSBR operated without nutrient addition obtained a constant methane production (0.26 L CH4/g COD), whereas the AnSBR operated with nutrient addition presented a gradual methane suppression. Molecular analyses suggested that methane suppression in the experiment with nutrient addition was due to a negative effect over the archaeal/bacterial ratio. PMID:25647030

  2. Effect of D-amino acid substitutions on Ni(II)-assisted peptide bond hydrolysis.

    PubMed

    Ariani, Hanieh H; Polkowska-Nowakowska, Agnieszka; Bal, Wojciech

    2013-03-01

    Previously we demonstrated the sequence-specific hydrolysis of the R1-(Ser/Thr)-peptide bond in Ni(II) complexes of peptides with a general R1-(Ser/Thr)-Xaa-His-Zaa-R2 sequence (R1 and R2 being any sequences) (Kopera, E.; Krezel, A.; Protas, A. M.; Belczyk, A.; Bonna, A.; Wyslouch-Cieszynska, A.; Poznanski, J.; Bal, W. Inorg. Chem. 2010, 49, 6636). In order to refine our understanding of the mechanism of this reaction and to find ways to accelerate it, we undertook a systematic study of effects of d-amino acid substitutions in the template Ac-Gly-Ala-Ser-Arg-His-Trp-Lys-Phe-Leu-NH2 peptide on the hydrolysis rate constants. We found that all stereochemical alterations made around the Ni(II) chelate plane resulted in the decrease of the reaction rate. However, the Ni(II) coordination, a prerequisite to the reaction, was not compromised by these substitutions. We demonstrated that the reaction is only possible when either the side chain of the crucial Ser (or Thr) residue is on the same part of the chelate plane as the next residue in the sequence (Arg), or the side chain of the residue following His (Trp) resides on the opposite side of the plane. The rate of reaction is the fastest when both these conditions are fulfilled. Another novel effect is the strong dependence of the rate of the acyl shift step on the character of the leaving group. PMID:23427909

  3. Methane production from acid hydrolysates of Agave tequilana bagasse: evaluation of hydrolysis conditions and methane yield.

    PubMed

    Arreola-Vargas, Jorge; Ojeda-Castillo, Valeria; Snell-Castro, Raúl; Corona-González, Rosa Isela; Alatriste-Mondragón, Felipe; Méndez-Acosta, Hugo O

    2015-04-01

    Evaluation of diluted acid hydrolysis for sugar extraction from cooked and uncooked Agave tequilana bagasse and feasibility of using the hydrolysates as substrate for methane production, with and without nutrient addition, in anaerobic sequencing batch reactors (AnSBR) were studied. Results showed that the hydrolysis over the cooked bagasse was more effective for sugar extraction at the studied conditions. Total sugars concentration in the cooked and uncooked bagasse hydrolysates were 27.9 g/L and 18.7 g/L, respectively. However, 5-hydroxymethylfurfural was detected in the cooked bagasse hydrolysate, and therefore, the uncooked bagasse hydrolysate was selected as substrate for methane production. Interestingly, results showed that the AnSBR operated without nutrient addition obtained a constant methane production (0.26 L CH4/g COD), whereas the AnSBR operated with nutrient addition presented a gradual methane suppression. Molecular analyses suggested that methane suppression in the experiment with nutrient addition was due to a negative effect over the archaeal/bacterial ratio.

  4. Enantioselective Hydrolysis of Amino Acid Esters Promoted by Bis(β-cyclodextrin) Copper Complexes

    NASA Astrophysics Data System (ADS)

    Xue, Shan-Shan; Zhao, Meng; Ke, Zhuo-Feng; Cheng, Bei-Chen; Su, Hua; Cao, Qian; Cao, Zhen-Kun; Wang, Jun; Ji, Liang-Nian; Mao, Zong-Wan

    2016-02-01

    It is challenging to create artificial catalysts that approach enzymes with regard to catalytic efficiency and selectivity. The enantioselective catalysis ranks the privileged characteristic of enzymatic transformations. Here, we report two pyridine-linked bis(β-cyclodextrin) (bisCD) copper(II) complexes that enantioselectively hydrolyse chiral esters. Hydrolytic kinetic resolution of three pairs of amino acid ester enantiomers (S1–S3) at neutral pH indicated that the “back-to-back” bisCD complex CuL1 favoured higher catalytic efficiency and more pronounced enantioselectivity than the “face-to-face” complex CuL2. The best enantioselectivity was observed for N-Boc-phenylalanine 4-nitrophenyl ester (S2) enantiomers promoted by CuL1, which exhibited an enantiomer selectivity of 15.7. We observed preferential hydrolysis of L-S2 by CuL1, even in racemic S2, through chiral high-performance liquid chromatography (HPLC). We demonstrated that the enantioselective hydrolysis was related to the cooperative roles of the intramolecular flanking chiral CD cavities with the coordinated copper ion, according to the results of electrospray ionization mass spectrometry (ESI-MS), inhibition experiments, rotating-frame nuclear Overhauser effect spectroscopy (ROESY), and theoretical calculations. Although the catalytic parameters lag behind the level of enzymatic transformation, this study confirms the cooperative effect of the first and second coordination spheres of artificial catalysts in enantioselectivity and provides hints that may guide future explorations of enzyme mimics.

  5. Enantioselective Hydrolysis of Amino Acid Esters Promoted by Bis(β-cyclodextrin) Copper Complexes

    NASA Astrophysics Data System (ADS)

    Xue, Shan-Shan; Zhao, Meng; Ke, Zhuo-Feng; Cheng, Bei-Chen; Su, Hua; Cao, Qian; Cao, Zhen-Kun; Wang, Jun; Ji, Liang-Nian; Mao, Zong-Wan

    2016-02-01

    It is challenging to create artificial catalysts that approach enzymes with regard to catalytic efficiency and selectivity. The enantioselective catalysis ranks the privileged characteristic of enzymatic transformations. Here, we report two pyridine-linked bis(β-cyclodextrin) (bisCD) copper(II) complexes that enantioselectively hydrolyse chiral esters. Hydrolytic kinetic resolution of three pairs of amino acid ester enantiomers (S1-S3) at neutral pH indicated that the “back-to-back” bisCD complex CuL1 favoured higher catalytic efficiency and more pronounced enantioselectivity than the “face-to-face” complex CuL2. The best enantioselectivity was observed for N-Boc-phenylalanine 4-nitrophenyl ester (S2) enantiomers promoted by CuL1, which exhibited an enantiomer selectivity of 15.7. We observed preferential hydrolysis of L-S2 by CuL1, even in racemic S2, through chiral high-performance liquid chromatography (HPLC). We demonstrated that the enantioselective hydrolysis was related to the cooperative roles of the intramolecular flanking chiral CD cavities with the coordinated copper ion, according to the results of electrospray ionization mass spectrometry (ESI-MS), inhibition experiments, rotating-frame nuclear Overhauser effect spectroscopy (ROESY), and theoretical calculations. Although the catalytic parameters lag behind the level of enzymatic transformation, this study confirms the cooperative effect of the first and second coordination spheres of artificial catalysts in enantioselectivity and provides hints that may guide future explorations of enzyme mimics.

  6. Enantioselective Hydrolysis of Amino Acid Esters Promoted by Bis(β-cyclodextrin) Copper Complexes.

    PubMed

    Xue, Shan-Shan; Zhao, Meng; Ke, Zhuo-Feng; Cheng, Bei-Chen; Su, Hua; Cao, Qian; Cao, Zhen-Kun; Wang, Jun; Ji, Liang-Nian; Mao, Zong-Wan

    2016-01-01

    It is challenging to create artificial catalysts that approach enzymes with regard to catalytic efficiency and selectivity. The enantioselective catalysis ranks the privileged characteristic of enzymatic transformations. Here, we report two pyridine-linked bis(β-cyclodextrin) (bisCD) copper(II) complexes that enantioselectively hydrolyse chiral esters. Hydrolytic kinetic resolution of three pairs of amino acid ester enantiomers (S1-S3) at neutral pH indicated that the "back-to-back" bisCD complex CuL(1) favoured higher catalytic efficiency and more pronounced enantioselectivity than the "face-to-face" complex CuL(2). The best enantioselectivity was observed for N-Boc-phenylalanine 4-nitrophenyl ester (S2) enantiomers promoted by CuL(1), which exhibited an enantiomer selectivity of 15.7. We observed preferential hydrolysis of L-S2 by CuL(1), even in racemic S2, through chiral high-performance liquid chromatography (HPLC). We demonstrated that the enantioselective hydrolysis was related to the cooperative roles of the intramolecular flanking chiral CD cavities with the coordinated copper ion, according to the results of electrospray ionization mass spectrometry (ESI-MS), inhibition experiments, rotating-frame nuclear Overhauser effect spectroscopy (ROESY), and theoretical calculations. Although the catalytic parameters lag behind the level of enzymatic transformation, this study confirms the cooperative effect of the first and second coordination spheres of artificial catalysts in enantioselectivity and provides hints that may guide future explorations of enzyme mimics. PMID:26916830

  7. EFFECT OF ANATOMICAL FRACTIONATION ON THE ENZYMATIC HYDROLYSIS OF ACID AND ALKALINE PRETREATED CORN STOVER

    SciTech Connect

    K. B. Duguid; M. D. Montross; C. W. Radtke; C. L. Crofcheck; L. M. Wendt; S. A. Shearer

    2009-11-01

    Due to concerns with biomass collection systems and soil sustainability there are opportunities to investigate the optimal plant fractions to collect for conversion. An ideal feedstock would require low severity pretreatment to release a maximum amount of sugar during enzymatic hydrolysis. Corn stover fractions were separated by hand and analyzed for glucan, xylan, acid soluble lignin, acid insoluble lignin, and ash composition. The stover fractions were also pretreated with either 0, 0.4, or 0.8% NaOH for 2 hours at room temperature, washed, autoclaved and saccharified. In addition, acid pretreated samples underwent simultaneous saccharification and fermentation (SSF) to ethanol. In general, the two pretreatments produced similar trends with cobs, husks, and leaves responding best to the pretreatments, the tops of stalks responding slightly less, and the bottom of the stalks responding the least. For example, corn husks pretreated with 0.8% NaOH released over 90% (standard error of 3.8%) of the available glucan, while only 45% (standard error of 1.1%) of the glucan was produced from identically treated stalk bottoms. Estimates of the theoretical ethanol yield using acid pretreatment followed by SSF were 65% (standard error of 15.9%) for husks and 29% (standard error of 1.8%) for stalk bottoms. This suggests that integration of biomass collection systems to remove sustainable feedstocks could be integrated with the processes within a biorefinery to minimize overall ethanol production costs.

  8. Lignin hydrolysis and phosphorylation mechanism during phosphoric acid-acetone pretreatment: a DFT study.

    PubMed

    Qin, Wu; Wu, Lingnan; Zheng, Zongming; Dong, Changqing; Yang, Yongping

    2014-12-18

    The study focused on the structural sensitivity of lignin during the phosphoric acid-acetone pretreatment process and the resulting hydrolysis and phosphorylation reaction mechanisms using density functional theory calculations. The chemical stabilities of the seven most common linkages (β-O-4, β-β, 4-O-5, β-1, 5-5, α-O-4, and β-5) of lignin in H3PO4, CH3COCH3, and H2O solutions were detected, which shows that α-O-4 linkage and β-O-4 linkage tend to break during the phosphoric acid-acetone pretreatment process. Then α-O-4 phosphorylation and β-O-4 phosphorylation follow a two-step reaction mechanism in the acid treatment step, respectively. However, since phosphorylation of α-O-4 is more energetically accessible than phosphorylation of β-O-4 in phosphoric acid, the phosphorylation of α-O-4 could be controllably realized under certain operational conditions, which could tune the electron and hole transfer on the right side of β-O-4 in the H2PO4- functionalized lignin. The results provide a fundamental understanding for process-controlled modification of lignin and the potential novel applications in lignin-based imprinted polymers, sensors, and molecular devices.

  9. Determination of amino acids in two Polysiphonia species and study of enzymatic hydrolysis method

    NASA Astrophysics Data System (ADS)

    Zhang, Li-Xin; Fan, Xiao; Wei, Yu-Xi

    2002-09-01

    The total content of the rich amino acids in two common red algae, Polysiphonia urceolata and Polysiphonia japonica growing in the Qingdao seashore were determined. The algae powder was hydrolyzed by 6 mol/L HCl at 110°C for 48 h and determined by amino acid analyzer. The content was 25.35% and 24.16%, respectively, much higher than that of some other species. In addition, a nutritive liquid with abundant amino acids was prepared (by the enzymatic hydrolysis method using Polysiphonia urceolata) as raw material for a kind of health beverage. The dried seaweed was decolored by 0.25% KMnO4 and 0.5% active carbon, then enzymalized. In the selection of enzymalizing condition, the orthogonal experimental design was used. Four factors including kinds of enzyme, quantity of enzyme, temperature and time were studied at 3 levels. According to the orthogonal design results, we can choose an optimal condition: hydrolyzing at 45°C by neutral proteinase (0.25%, w/w) for 2h, adjusting pH to 8.5, then adding trypsin (0.25%, w/w) and hydrolyzing for 2 h. Finally the above solution was alkalized by NaOH and neutralized by casein. After the hydrolyzed liquid was filtered and concentrated, suitable additives were added. The final products contain rich amino acids.

  10. Cellulose nanocrystals prepared via formic acid hydrolysis followed by TEMPO-mediated oxidation.

    PubMed

    Li, Bin; Xu, Wenyang; Kronlund, Dennis; Määttänen, Anni; Liu, Jun; Smått, Jan-Henrik; Peltonen, Jouko; Willför, Stefan; Mu, Xindong; Xu, Chunlin

    2015-11-20

    Cellulose nanocrystals (CNCs) as a renewable and biodegradable nanomaterial have wide application value. In this work, CNCs were extracted from bleached chemical pulp using two stages of isolation (i.e. formic acid (FA) hydrolysis and 2,2,6,6-tetramethyl-piperidine-1-oxyl (TEMPO) mediated oxidation) under mild conditions. In the first stage, FA was used to remove hemicellulose, swell cellulose fibers, and release CNCs. The FA could be readily recovered and reused. In the second stage, the CNCs isolated by FA were further modified by TEMPO-mediated oxidation to increase the surface charge of CNCs. It was found that the modified CNCs with more ordered crystal structure and higher surface charge had better redispersibility and higher viscosity in aqueous phase. Therefore, the modified CNCs could be more effective when used as rheology modifier in the fields of water based coating, paint, food etc.

  11. Steam gasification of acid-hydrolysis biomass CAHR for clean syngas production.

    PubMed

    Chen, Guanyi; Yao, Jingang; Yang, Huijun; Yan, Beibei; Chen, Hong

    2015-03-01

    Main characteristics of gaseous product from steam gasification of acid-hydrolysis biomass CAHR have been investigated experimentally. The comparison in terms of evolution of syngas flow rate, syngas quality and apparent thermal efficiency was made between steam gasification and pyrolysis in the lab-scale apparatus. The aim of this study was to determine the effects of temperature and steam to CAHR ratio on gas quality, syngas yield and energy conversion. The results showed that syngas and energy yield were better with gasification compared to pyrolysis under identical thermal conditions. Both high gasification temperature and introduction of proper steam led to higher gas quality, higher syngas yield and higher energy conversion efficiency. However, excessive steam reduced hydrogen yield and energy conversion efficiency. The optimal value of S/B was found to be 3.3. The maximum value of energy ratio was 0.855 at 800°C with the optimal S/B value.

  12. Steam gasification of acid-hydrolysis biomass CAHR for clean syngas production.

    PubMed

    Chen, Guanyi; Yao, Jingang; Yang, Huijun; Yan, Beibei; Chen, Hong

    2015-03-01

    Main characteristics of gaseous product from steam gasification of acid-hydrolysis biomass CAHR have been investigated experimentally. The comparison in terms of evolution of syngas flow rate, syngas quality and apparent thermal efficiency was made between steam gasification and pyrolysis in the lab-scale apparatus. The aim of this study was to determine the effects of temperature and steam to CAHR ratio on gas quality, syngas yield and energy conversion. The results showed that syngas and energy yield were better with gasification compared to pyrolysis under identical thermal conditions. Both high gasification temperature and introduction of proper steam led to higher gas quality, higher syngas yield and higher energy conversion efficiency. However, excessive steam reduced hydrogen yield and energy conversion efficiency. The optimal value of S/B was found to be 3.3. The maximum value of energy ratio was 0.855 at 800°C with the optimal S/B value. PMID:25553562

  13. RAPESEED PHOSPHATIDYLCHOLINE HYDROLYSIS TO PHOSPHATIDIC ACID USING PLANT EXTRACTS WITH PHOPSPHOLIPASE D.

    PubMed

    Pasker, Beata; Sosada, Marian; Fraś, Paweł; Boryczka, Monika; Górecki, Michał; Zych, Maria

    2015-01-01

    Phosphatidic acid (PA) has a crucial role in cell membrane structure and function. For that reason it has a possible application in the treatment of some health disorders in humans, can be used as a natural and non toxic emulsifier and the component of drug carriers in pharmaceuticals and cosmetics as well as a component for synthesis of some new phospholipids. PA is short-lived in the cell and is difficult to extract directly from the biological material. PA may be easily prepared by hydrolysis of phospholipids, especially phosphatidylcholine (PC), using cabbage phospholipase D (PLD). Hydrolytic activity of purified by us PLD extracts from cabbage towards rapeseed phosphatidylcholine (RPC) was investigated. Hydrolysis was carried out in the biphasic system (water/diethyl ether) at pH 6,5 and temp 30°C. Influence of enzymatic extracts from three cabbage varieties, reaction time, Ca2+ concentration and enzyme extracts/PC ratio, on activity towards RPC resulting in rapeseed phosphatidic acid (RPA) formation were examined. Our study shows that the PLD extracts from savoy cabbage (PLDsc), white cabbage (PLDwc) and brussels sprouts (PLDbs) used in experiments exhibit hydrolytic activity towards RPC resulting in rapeseed RPA with different yield. The highest activity towards RPC shows PLD extract from PLDsc with the RPC conversion degree to RPA (90%) was observed at 120 mM Ca2+ concentration, reaction time 60 min and ratio of PLD extract to RPC 6 : 1 (w/w). Our study shows that purified by us PLDsc extracts exhibit hydrolytic activity towards RPC giving new RPA with satisfying conversion degree for use in pharmacy, cosmetics and as a standard in analytical chemistry.

  14. RAPESEED PHOSPHATIDYLCHOLINE HYDROLYSIS TO PHOSPHATIDIC ACID USING PLANT EXTRACTS WITH PHOPSPHOLIPASE D.

    PubMed

    Pasker, Beata; Sosada, Marian; Fraś, Paweł; Boryczka, Monika; Górecki, Michał; Zych, Maria

    2015-01-01

    Phosphatidic acid (PA) has a crucial role in cell membrane structure and function. For that reason it has a possible application in the treatment of some health disorders in humans, can be used as a natural and non toxic emulsifier and the component of drug carriers in pharmaceuticals and cosmetics as well as a component for synthesis of some new phospholipids. PA is short-lived in the cell and is difficult to extract directly from the biological material. PA may be easily prepared by hydrolysis of phospholipids, especially phosphatidylcholine (PC), using cabbage phospholipase D (PLD). Hydrolytic activity of purified by us PLD extracts from cabbage towards rapeseed phosphatidylcholine (RPC) was investigated. Hydrolysis was carried out in the biphasic system (water/diethyl ether) at pH 6,5 and temp 30°C. Influence of enzymatic extracts from three cabbage varieties, reaction time, Ca2+ concentration and enzyme extracts/PC ratio, on activity towards RPC resulting in rapeseed phosphatidic acid (RPA) formation were examined. Our study shows that the PLD extracts from savoy cabbage (PLDsc), white cabbage (PLDwc) and brussels sprouts (PLDbs) used in experiments exhibit hydrolytic activity towards RPC resulting in rapeseed RPA with different yield. The highest activity towards RPC shows PLD extract from PLDsc with the RPC conversion degree to RPA (90%) was observed at 120 mM Ca2+ concentration, reaction time 60 min and ratio of PLD extract to RPC 6 : 1 (w/w). Our study shows that purified by us PLDsc extracts exhibit hydrolytic activity towards RPC giving new RPA with satisfying conversion degree for use in pharmacy, cosmetics and as a standard in analytical chemistry. PMID:26642684

  15. Acidic 1,3-propanediaminetetraacetato lanthanides with luminescent and catalytic ester hydrolysis properties

    SciTech Connect

    Chen, Mao-Long; Shi, Yan-Ru; Yang, Yu-Chen; Zhou, Zhao-Hui

    2014-11-15

    In acidic solution, a serials of water-soluble coordination polymers (CPs) were isolated as zonal 1D-CPs 1,3-propanediaminetetraacetato lanthanides [Ln(1,3-H{sub 3}pdta)(H{sub 2}O){sub 5}]{sub n}·2Cl{sub n}·3nH{sub 2}O [Ln=La, 1; Ce, 2; Pr, 3; Nd, 4; Sm, 5] (1,3-H{sub 4}pdta=1,3-propanediaminetetraacetic acid, C{sub 11}H{sub 18}N{sub 2}O{sub 8}) in high yields. When 1 eq. mol potassium hydroxide was added to the solutions of 1D-CPs, respectively, two 1D-CPs [Ln(1,3-H{sub 2}pdta)(H{sub 2}O){sub 3}]{sub n}·Cl{sub n}·2nH{sub 2}O [Ln=Sm, 6; Gd, 7] were isolated at room temperature and seven 2D-CPs [Ln(1,3-H{sub 2}pdta)(H{sub 2}O){sub 2}]{sub n}·Cl{sub n}·2nH{sub 2}O [Ln=La, 8; Ce, 9; Pr, 10; Nd, 11; Sm, 12; Eu, 13; Gd, 14] were isolated at 70 °C. When the crystals of 1–4 were hydrothermally heated at 180 °C with 1–2 eq. mol potassium hydroxide, four 3D-CPs [Ln(1,3-Hpdta)]{sub n}·nH{sub 2}O [Ln=La, 15; Ce, 16; Pr, 17; Nd, 18] were obtained. The two 2D-CPs [Ln(1,3-Hpdta)(H{sub 2}O)]{sub n}·4nH{sub 2}O (Sm, 19; Eu, 20) were isolated in similar reaction conditions. With the increments of pH value in the solution and reaction temperature, the structure becomes more complicated. 1–5 are soluble in water and 1 was traced by solution {sup 13}C({sup 1}H) NMR technique, the water-soluble lanthanides 1 and 5 show catalytic activity to ester hydrolysis reaction respectively, which indicate their important roles in the hydrolytic reaction. The europium complexes 13 and 20 show visible fluorescence at an excitation of 394 nm. The structure diversity is mainly caused by the variation of coordinated ligand in different pH values and lanthanide contraction effect. Acidic conditions are favorable for the isolations of lanthanide complexes in different structures and this may helpful to separate different lanthanides. The thermal stability investigations reveal that acidic condition is favorable to obtain the oxides at a lower temperature. - Graphical abstract: A series

  16. Acid and base hydrolysis of lipid A from Enterobacter agglomerans as monitored by electrospray ionization mass spectrometry: pertinence to detoxification mechanisms.

    PubMed

    Wang, Y; Cole, R B

    1996-02-01

    Lipopolysaccharides (LPS), which are endotoxins found in the cell wall of Gram-negative bacteria, are common components of organic dusts that cause or contribute to symptoms associated with organic dust diseases. The lipid A subgroup within LPS is believed to be responsible for the toxicity. Acid and base treatments, which can be effective detoxification methods, were performed on lipid A from Enterobacter agglomerans (EA), a bacterium commonly found in field cotton. Negative-ion electrospray ionization mass spectrometry was employed to characterize the post-treatment structural changes to lipid A. Acid treatment (1% acetic acid, 100 degrees C) hydrolyzed the ester side-chains of lipid A. It was found that the ester-linked palmitoyl group was the most labile to acid hydrolysis. Hydrolysis of the palmitoyl moiety conformed to pseudo-first-order chemical reaction kinetics with a rate constant for decomposition of heptacyl-lipid A from Enterobacter agglomerans of approximately 3.3 x 10(-3) min-1. An order of lability of lipid A acyl side-chains to acid hydrolysis was also deduced: R4' (palmitoyl) > R1' (myristoyl or hydroxymyristoyl) > R3 (hydroxymyristoyl at position 3) > R1 (oxymyristoyl group at position 3') > R2' (lauroyl). Base treatment (0.05 M NaOH in 95% EtOH, 65 degrees C) was shown to be more effective at cleaving ester-linked side-chains. In addition, mass spectral evidence suggests that opening of the pyranose rings of the disaccharide backbone of lipid A and/or removal of the phosphoryl groups may be occurring during base treatment. This study sheds light on mechanistic aspects of treatment procedures leading to the detoxification of endotoxins.

  17. Direct lactic acid fermentation of Jerusalem artichoke tuber extract using Lactobacillus paracasei without acidic or enzymatic inulin hydrolysis.

    PubMed

    Choi, Hwa-Young; Ryu, Hee-Kyoung; Park, Kyung-Min; Lee, Eun Gyo; Lee, Hongweon; Kim, Seon-Won; Choi, Eui-Sung

    2012-06-01

    Lactic acid fermentation of Jerusalem artichoke tuber was performed with strains of Lactobacillus paracasei without acidic or enzymatic inulin hydrolysis prior to fermentation. Some strains of L. paracasei, notably KCTC13090 and KCTC13169, could ferment hot-water extract of Jerusalem artichoke tuber more efficiently compared with other Lactobacillus spp. such as L. casei type strain KCTC3109. The L. paracasei strains could utilize almost completely the fructo-oligosaccharides present in Jerusalem artichoke. Inulin-fermenting L. paracasei strains produced c.a. six times more lactic acid compared with L. casei KCTC3109. Direct lactic fermentation of Jerusalem artichoke tuber extract at 111.6g/L of sugar content with a supplement of 5 g/L of yeast extract by L. paracasei KCTC13169 in a 5L jar fermentor produced 92.5 ce:hsp sp="0.25"/>g/L of lactic acid with 16.8 g/L fructose equivalent remained unutilized in 72 h. The conversion efficiency of inulin-type sugars to lactic acid was 98% of the theoretical yield.

  18. Effect of degree of hydrolysis of whey protein on in vivo plasma amino acid appearance in humans.

    PubMed

    Farup, Jean; Rahbek, Stine Klejs; Storm, Adam C; Klitgaard, Søren; Jørgensen, Henry; Bibby, Bo M; Serena, Anja; Vissing, Kristian

    2016-01-01

    Whey protein is generally found to be faster digested and to promote faster and higher increases in plasma amino acid concentrations during the immediate ~60 min following protein ingestion compared to casein. The aim of the present study was to compare three different whey protein hydrolysates with varying degrees of hydrolysis (DH, % cleaved peptide bonds) to evaluate if the degree of whey protein hydrolysis influences the rate of amino acid plasma appearance in humans. A casein protein was included as reference. The three differentially hydrolysed whey proteins investigated were: High degree of hydrolysis (DH, DH = 48 %), Medium DH (DH = 27 %), and Low DH (DH = 23 %). The casein protein was intact. Additionally, since manufacturing of protein products may render some amino acids unavailable for utilisation in the body the digestibility and the biological value of all four protein fractions were evaluated in a rat study. A two-compartment model for the description of the postprandial plasma amino acid kinetics was applied to investigate the rate of postprandial total amino acid plasma appearance of the four protein products. The plasma amino acid appearance rates of the three whey protein hydrolysates (WPH) were all significantly higher than for the casein protein, however, the degree of hydrolysis of the WPH products did not influence plasma total amino acid appearance rate (estimates of DH and 95 % confidence intervals [CI] (mol L(-1) min(-1)): High DH 0.0585 [0.0454, 0.0754], Medium DH 0.0594 [0.0495, 0.0768], Low DH 0.0560 [0.0429, 0.0732], Casein 0.0194 [0.0129, 0.0291]). The four protein products were all highly digestible, while the biological value decreased with increasing degree of hydrolysis. In conclusion, the current study does not provide evidence that the degree of whey protein hydrolysis is a strong determinant for plasma amino acid appearance rate within the studied range of hydrolysis and protein dose. PMID:27065230

  19. Structure of Human Acid Sphingomyelinase Reveals the Role of the Saposin Domain in Activating Substrate Hydrolysis.

    PubMed

    Xiong, Zi-Jian; Huang, Jingjing; Poda, Gennady; Pomès, Régis; Privé, Gilbert G

    2016-07-31

    Acid sphingomyelinase (ASM) is a lysosomal phosphodiesterase that catalyzes the hydrolysis of sphingomyelin to produce ceramide and phosphocholine. While other lysosomal sphingolipid hydrolases require a saposin activator protein for full activity, the ASM polypeptide incorporates a built-in N-terminal saposin domain and does not require an external activator protein. Here, we report the crystal structure of human ASM and describe the organization of the three main regions of the enzyme: the N-terminal saposin domain, the proline-rich connector, and the catalytic domain. The saposin domain is tightly associated along an edge of the large, bowl-shaped catalytic domain and adopts an open form that exposes a hydrophobic concave surface approximately 30Å from the catalytic center. The calculated electrostatic potential of the enzyme is electropositive at the acidic pH of the lysosome, consistent with the strict requirement for the presence of acidic lipids in target membranes. Docking studies indicate that sphingomyelin binds with the ceramide-phosphate group positioned at the binuclear zinc center and molecular dynamic simulations indicate that the intrinsic flexibility of the saposin domain is important for monomer-dimer exchange and for membrane interactions. Overall, ASM uses a combination of electrostatic and hydrophobic interactions to cause local disruptions of target bilayers in order to bring the lipid headgroup to the catalytic center in a membrane-bound reaction. PMID:27349982

  20. Structure of Human Acid Sphingomyelinase Reveals the Role of the Saposin Domain in Activating Substrate Hydrolysis.

    PubMed

    Xiong, Zi-Jian; Huang, Jingjing; Poda, Gennady; Pomès, Régis; Privé, Gilbert G

    2016-07-31

    Acid sphingomyelinase (ASM) is a lysosomal phosphodiesterase that catalyzes the hydrolysis of sphingomyelin to produce ceramide and phosphocholine. While other lysosomal sphingolipid hydrolases require a saposin activator protein for full activity, the ASM polypeptide incorporates a built-in N-terminal saposin domain and does not require an external activator protein. Here, we report the crystal structure of human ASM and describe the organization of the three main regions of the enzyme: the N-terminal saposin domain, the proline-rich connector, and the catalytic domain. The saposin domain is tightly associated along an edge of the large, bowl-shaped catalytic domain and adopts an open form that exposes a hydrophobic concave surface approximately 30Å from the catalytic center. The calculated electrostatic potential of the enzyme is electropositive at the acidic pH of the lysosome, consistent with the strict requirement for the presence of acidic lipids in target membranes. Docking studies indicate that sphingomyelin binds with the ceramide-phosphate group positioned at the binuclear zinc center and molecular dynamic simulations indicate that the intrinsic flexibility of the saposin domain is important for monomer-dimer exchange and for membrane interactions. Overall, ASM uses a combination of electrostatic and hydrophobic interactions to cause local disruptions of target bilayers in order to bring the lipid headgroup to the catalytic center in a membrane-bound reaction.

  1. Hydrolysis of tannic acid catalyzed by immobilized-stabilized derivatives of Tannase from Lactobacillus plantarum.

    PubMed

    Curiel, Jose Antonio; Betancor, Lorena; de las Rivas, Blanca; Muñoz, Rosario; Guisan, Jose M; Fernández-Lorente, Gloria

    2010-05-26

    A recombinant tannase from Lactobacillus plantarum , overexpressed in Escherichia coli , was purified in a single step by metal chelate affinity chromatography on poorly activated nickel supports. It was possible to obtain 0.9 g of a pure enzyme by using only 20 mL of chromatographic support. The pure enzyme was immobilized and stabilized by multipoint covalent immobilization on highly activated glyoxyl agarose. Derivatives obtained by multipoint and multisubunit immobilization were 500- and 1000-fold more stable than both the soluble enzyme and the one-point-immobilized enzyme in experiments of thermal and cosolvent inactivation, respectively. In addition, up to 70 mg of pure enzyme was immobilized on 1 g of wet support. The hydrolysis of tannic acid was optimized by using the new immobilized tannase derivative. The optimal reaction conditions were 30% diglyme at pH 5.0 and 4 degrees C. Under these conditions, it was possible to obtain 47.5 mM gallic acid from 5 mM tannic acid as substrate. The product was pure as proved by HPLC. On the other hand, the immobilized biocatalyst preserved >95% of its initial activity after 1 month of incubation under the optimal reaction conditions.

  2. Acid-catalyzed hydrolysis of lignin β-O-4 linkages in ionic liquid solvents: a computational mechanistic study.

    PubMed

    Janesko, Benjamin G

    2014-03-21

    This work presents a computational mechanistic study of the acid-catalyzed hydrolysis of lignin β-O-4 linkages in ionic liquid solvents. Model compound 2-hydroyxyethyl phenyl ether undergoes dehydration to vinyl phenyl ether followed by hydrolysis to phenol and "Hibbert's ketones". Larger model compound α-hydroxy-phenethyl phenyl ether illustrates an E1 dehydration mechanism involving resonance-stabilized carbocations. Continuum models for ionic liquid solvents indicate that solvation can significantly affect the reaction rates. The tested continuum ionic liquid solvents give similar results, and differ significantly from continuum organic solvents with comparable dielectric constants. The acidic ionic liquid cation 1-H-3-methylimidazolium has lower predicted catalytic activity than hydronium or HCl, consistent with the former's relatively small acid dissociation constant. Calculations with dispersion-corrected density functionals give similar behavior. Calculations on Lewis acidic metal chlorides used experimentally for lignin hydrolysis suggest that the metal chloride may participate in the initial dehydration. These results provide a baseline for future studies of improved hydrolysis catalysts. PMID:24509442

  3. Cholesterol efflux from THP-1 macrophages is impaired by the fatty acid component from lipoprotein hydrolysis by lipoprotein lipase

    SciTech Connect

    Yang, Yanbo; Thyagarajan, Narmadaa; Coady, Breanne M.; Brown, Robert J.

    2014-09-05

    Highlights: • Lipoprotein hydrolysis products were produced by lipoprotein lipase. • Hydrolysis products lowers expression of macrophage cholesterol transporters. • Hydrolysis products reduces expression of select nuclear receptors. • Fatty acid products lowers cholesterol transporters and select nuclear receptors. • Fatty acid products reduces cholesterol efflux from macrophages. - Abstract: Lipoprotein lipase (LPL) is an extracellular lipase that primarily hydrolyzes triglycerides within circulating lipoproteins. Macrophage LPL contributes to atherogenesis, but the mechanisms behind it are poorly understood. We hypothesized that the products of lipoprotein hydrolysis generated by LPL promote atherogenesis by inhibiting the cholesterol efflux ability by macrophages. To test this hypothesis, we treated human THP-1 macrophages with total lipoproteins that were hydrolyzed by LPL and we found significantly reduced transcript levels for the cholesterol transporters ATP binding cassette transporter A1 (ABCA1), ABCG1, and scavenger receptor BI. These decreases were likely due to significant reductions for the nuclear receptors liver-X-receptor-α, peroxisome proliferator activated receptor (PPAR)-α, and PPAR-γ. We prepared a mixture of free fatty acids (FFA) that represented the ratios of FFA species within lipoprotein hydrolysis products, and we found that the FFA mixture also significantly reduced cholesterol transporters and nuclear receptors. Finally, we tested the efflux of cholesterol from THP-1 macrophages to apolipoprotein A-I, and we found that the treatment of THP-1 macrophages with the FFA mixture significantly attenuated cholesterol efflux. Overall, these data show that the FFA component of lipoprotein hydrolysis products generated by LPL may promote atherogenesis by inhibiting cholesterol efflux, which partially explains the pro-atherogenic role of macrophage LPL.

  4. Hydrolysis of biomass using a reusable solid carbon acid catalyst and fermentation of the catalytic hydrolysate to ethanol.

    PubMed

    Goswami, Mandavi; Meena, S; Navatha, S; Prasanna Rani, K N; Pandey, Ashok; Sukumaran, Rajeev Kumar; Prasad, R B N; Prabhavathi Devi, B L A

    2015-01-01

    Solid acid catalysts can hydrolyze cellulose with lower reaction times and are easy to recover and reuse. A glycerol based carbon acid catalyst developed at CSIR-IICT performed well in acid catalysis reactions and hence this study was undertaken to evaluate the catalyst for hydrolysis of biomass (alkali pretreated or native rice straw). The catalyst could release 262 mg/g total reducing sugars (TRS) in 4h at 140 °C from alkali pretreated rice straw, and more importantly it released 147 mg/g TRS from native biomass. Reusability of the catalyst was also demonstrated. Catalytic hydrolysate was used as sugar source for fermentation to produce ethanol. Results indicate the solid acid catalyst as an interesting option for biomass hydrolysis.

  5. Potential of phosphoric acid-catalyzed pretreatment and subsequent enzymatic hydrolysis for biosugar production from Gracilaria verrucosa.

    PubMed

    Kwon, Oh-Min; Kim, Sung-Koo; Jeong, Gwi-Taek

    2016-07-01

    This study combined phosphoric acid-catalyzed pretreatment and enzymatic hydrolysis to produce biosugars from Gracilaria verrucosa as a potential renewable resource for bioenergy applications. We optimized phosphoric acid-catalyzed pretreatment conditions to 1:10 solid-to-liquid ratio, 1.5 % phosphoric acid, 140 °C, and 60 min reaction time, producing a 32.52 ± 0.06 % total reducing sugar (TRS) yield. By subsequent enzymatic hydrolysis, a 68.61 ± 0.90 % TRS yield was achieved. These results demonstrate the potential of phosphoric acid to produce biosugars for biofuel and biochemical production applications. PMID:27003825

  6. Potential of phosphoric acid-catalyzed pretreatment and subsequent enzymatic hydrolysis for biosugar production from Gracilaria verrucosa.

    PubMed

    Kwon, Oh-Min; Kim, Sung-Koo; Jeong, Gwi-Taek

    2016-07-01

    This study combined phosphoric acid-catalyzed pretreatment and enzymatic hydrolysis to produce biosugars from Gracilaria verrucosa as a potential renewable resource for bioenergy applications. We optimized phosphoric acid-catalyzed pretreatment conditions to 1:10 solid-to-liquid ratio, 1.5 % phosphoric acid, 140 °C, and 60 min reaction time, producing a 32.52 ± 0.06 % total reducing sugar (TRS) yield. By subsequent enzymatic hydrolysis, a 68.61 ± 0.90 % TRS yield was achieved. These results demonstrate the potential of phosphoric acid to produce biosugars for biofuel and biochemical production applications.

  7. Enantioselective Hydrolysis of Amino Acid Esters Promoted by Bis(β-cyclodextrin) Copper Complexes

    PubMed Central

    Xue, Shan-Shan; Zhao, Meng; Ke, Zhuo-Feng; Cheng, Bei-Chen; Su, Hua; Cao, Qian; Cao, Zhen-Kun; Wang, Jun; Ji, Liang-Nian; Mao, Zong-Wan

    2016-01-01

    It is challenging to create artificial catalysts that approach enzymes with regard to catalytic efficiency and selectivity. The enantioselective catalysis ranks the privileged characteristic of enzymatic transformations. Here, we report two pyridine-linked bis(β-cyclodextrin) (bisCD) copper(II) complexes that enantioselectively hydrolyse chiral esters. Hydrolytic kinetic resolution of three pairs of amino acid ester enantiomers (S1–S3) at neutral pH indicated that the “back-to-back” bisCD complex CuL1 favoured higher catalytic efficiency and more pronounced enantioselectivity than the “face-to-face” complex CuL2. The best enantioselectivity was observed for N-Boc-phenylalanine 4-nitrophenyl ester (S2) enantiomers promoted by CuL1, which exhibited an enantiomer selectivity of 15.7. We observed preferential hydrolysis of L-S2 by CuL1, even in racemic S2, through chiral high-performance liquid chromatography (HPLC). We demonstrated that the enantioselective hydrolysis was related to the cooperative roles of the intramolecular flanking chiral CD cavities with the coordinated copper ion, according to the results of electrospray ionization mass spectrometry (ESI-MS), inhibition experiments, rotating-frame nuclear Overhauser effect spectroscopy (ROESY), and theoretical calculations. Although the catalytic parameters lag behind the level of enzymatic transformation, this study confirms the cooperative effect of the first and second coordination spheres of artificial catalysts in enantioselectivity and provides hints that may guide future explorations of enzyme mimics. PMID:26916830

  8. Conversion of levulinic acid into γ-valerolactone using Fe3(CO)12: mimicking a biorefinery setting by exploiting crude liquors from biomass acid hydrolysis.

    PubMed

    Metzker, Gustavo; Burtoloso, Antonio C B

    2015-09-28

    The conversion of biomass-derived levulinic acid (LA) into gamma-valerolactone (GVL) using formic acid (FA) and Fe3(CO)12 as the catalyst precursor was achieved in 92% yield. To mimic a biorefinery setting, crude liquor (containing 20% LA) from the acid hydrolysis of sugarcane biomass in a pilot plant facility was directly converted into GVL in good yield (50%), without the need for isolating LA.

  9. Conversion of levulinic acid into γ-valerolactone using Fe3(CO)12: mimicking a biorefinery setting by exploiting crude liquors from biomass acid hydrolysis.

    PubMed

    Metzker, Gustavo; Burtoloso, Antonio C B

    2015-09-28

    The conversion of biomass-derived levulinic acid (LA) into gamma-valerolactone (GVL) using formic acid (FA) and Fe3(CO)12 as the catalyst precursor was achieved in 92% yield. To mimic a biorefinery setting, crude liquor (containing 20% LA) from the acid hydrolysis of sugarcane biomass in a pilot plant facility was directly converted into GVL in good yield (50%), without the need for isolating LA. PMID:26258183

  10. Cassava starch maltodextrinization/monomerization through thermopressurized aqueous phosphoric acid hydrolysis.

    PubMed

    Fontana, J D; Passos, M; Baron, M; Mendes, S V; Ramos, L P

    2001-01-01

    Kinetic conditions were established for the depolymerization of cassava starch for the production of maltodextrins and glucose syrups. Thin-layer chromatography and high-performance liquid chromatography analyses corroborated that the proper H3PO4 strength and thermopressurization range (e.g., 142-170 degrees C; 2.8-6.8 atm) can be successfully explored for such hydrolytic purposes of native starch granules. Because phosphoric acid can be advantageously maintained in the hydrolysate and generates, after controlled neutralization with ammonia, the strategic nutrient triplet for industrial fermentations (C, P, N), this pretreatment strategy can be easily recognized as a recommended technology for hydrolysis and upgrading of starch and other plant polysaccharides. Compared to the classic catalysts, the mandatory desalting step (chloride removal by expensive anion-exchange resin or sulfate precipitation as the calcium-insoluble salt) can be avoided. Furthermore, properly diluted phosphoric acid is well known as an allowable additive in several popular soft drinks such as colas since its acidic feeling in the mouth is compatible and synergistic with both natural and artificial sweeteners. Glycosyrups from phosphorolyzed cassava starch have also been upgraded to high-value single-cell protein such as the pigmented yeast biomass of Xanthophyllomyces dendrorhous (Phaffia rhodozyma), whose astaxanthin (diketo-dihydroxy-beta-carotene) content may reach 0.5-1.0 mg/g of dry yeast cell. This can be used as an ideal complement for animal feeding as well as a natural staining for both fish farming (meat) and poultry (eggs). PMID:11963875

  11. [Determination of docosahexaenoic acid in milk powder by gas chromatography using acid hydrolysis].

    PubMed

    Shao, Shiping; Xiang, Dapeng; Li, Shuang; Xi, Xinglin; Chen, Wenrui

    2015-11-01

    A method to determine docosahexenoic acid (DHA) in milk powder by gas chromatography was established. The milk powder samples were hydrolyzed with hydrochloric acid, extracted to get total fatty acids by Soxhlet extractor, then esterified with potassium hydroxide methanol solution to form methyl esters, and treated with sodium hydrogen sulfate. The optimal experiment conditions were obtained from orthogonal experiment L9(3(3)) which performed with three factors and three levels, and it requires the reaction performed with 1 mol/L potassium hydroxide solution at 25 degrees C for 5 min. The derivative treated with sodium hydrogen sulfate was separated on a column of SP-2560 (100 m x 0.25 mm x 0.20 μm), and determined in 55 min by temperature programming-gas chromatography. Good linearity was obtained in the range 5.0-300 mg/L with the correlation coefficient of 0.999 9. The relative standard deviations (RSDs) were 3.4%, 1.2% and 1.1% for the seven repeated experiments of 10, 50 and 100 mg/L of DHA, respectively. The limit of detection was 2 mg/kg, and the recoveries of DHA were in the range of 90.4%-93.5%. The results are satisfactory through the tests of practical samples. PMID:26939370

  12. Selection of suitable mineral acid and its concentration for biphasic dilute acid hydrolysis of the sodium dithionite delignified Prosopis juliflora to hydrolyze maximum holocellulose.

    PubMed

    Naseeruddin, Shaik; Desai, Suseelendra; Venkateswar Rao, L

    2016-02-01

    Two grams of delignified substrate at 10% (w/v) level was subjected to biphasic dilute acid hydrolysis using phosphoric acid, hydrochloric acid and sulfuric acid separately at 110 °C for 10 min in phase-I and 121 °C for 15 min in phase-II. Combinations of acid concentrations in two phases were varied for maximum holocellulose hydrolysis with release of fewer inhibitors, to select the suitable acid and its concentration. Among three acids, sulfuric acid in combination of 1 & 2% (v/v) hydrolyzed maximum holocellulose of 25.44±0.44% releasing 0.51±0.02 g/L of phenolics and 0.12±0.002 g/L of furans, respectively. Further, hydrolysis of delignified substrate using selected acid by varying reaction time and temperature hydrolyzed 55.58±1.78% of holocellulose releasing 2.11±0.07 g/L and 1.37±0.03 g/L of phenolics and furans, respectively at conditions of 110 °C for 45 min in phase-I & 121 °C for 60 min in phase-II. PMID:26716889

  13. Selection of suitable mineral acid and its concentration for biphasic dilute acid hydrolysis of the sodium dithionite delignified Prosopis juliflora to hydrolyze maximum holocellulose.

    PubMed

    Naseeruddin, Shaik; Desai, Suseelendra; Venkateswar Rao, L

    2016-02-01

    Two grams of delignified substrate at 10% (w/v) level was subjected to biphasic dilute acid hydrolysis using phosphoric acid, hydrochloric acid and sulfuric acid separately at 110 °C for 10 min in phase-I and 121 °C for 15 min in phase-II. Combinations of acid concentrations in two phases were varied for maximum holocellulose hydrolysis with release of fewer inhibitors, to select the suitable acid and its concentration. Among three acids, sulfuric acid in combination of 1 & 2% (v/v) hydrolyzed maximum holocellulose of 25.44±0.44% releasing 0.51±0.02 g/L of phenolics and 0.12±0.002 g/L of furans, respectively. Further, hydrolysis of delignified substrate using selected acid by varying reaction time and temperature hydrolyzed 55.58±1.78% of holocellulose releasing 2.11±0.07 g/L and 1.37±0.03 g/L of phenolics and furans, respectively at conditions of 110 °C for 45 min in phase-I & 121 °C for 60 min in phase-II.

  14. Hydrolysis of chicoric and caftaric acids with esterases and Lactobacillus johnsonii in Vitro and in a gastrointestinal model.

    PubMed

    Bel-Rhlid, Rachid; Pagé-Zoerkler, Nicole; Fumeaux, René; Ho-Dac, Thang; Chuat, Jean-Yves; Sauvageat, Jean Luc; Raab, Thomas

    2012-09-12

    Chicoric acid (ChA) and caftaric acid (CafA) were identified as bioactive components of chicory and have been ascribed a number of health benefits. This study investigated the hydrolysis of ChA and CafA with enzymes and a probiotic bacterium Lactobacillus johnsonii (La1). Esterase from Aspergillus japonicus (24 U/mg) hydrolyzed 100% of ChA (5 mM) and CafA (5 mM) after 3 h, at pH 7.0 and 37 °C. Under the same reaction conditions, 100% hydrolysis of ChA and CafA was achieved with a spray-dried preparation of La1. The addition of La1 (100 mg/mL, 3.3 E9 cfu/g) to CafA solution in a gastrointestinal model (GI model) resulted in 65% hydrolysis of CafA. This model simulates the physicochemical conditions of the human gastrointestinal tract. No hydrolysis of CafA was observed after passage through the GI model in the absence of La1. The results of this study support the hypothesis that ChA and CafA are degraded by gut microflora before absorption and metabolization. PMID:22920606

  15. Three competitive transition states at the glycosidic bond of sucrose in its acid-catalyzed hydrolysis.

    PubMed

    Yamabe, Shinichi; Guan, Wei; Sakaki, Shigeyoshi

    2013-03-15

    The acid-catalyzed hydrolysis of sucrose to glucose and fructose was investigated by DFT calculations. Protonations to three ether oxygen atoms of the sucrose molecule, A, B, and (C, D), were compared. Three (B, the fructosyl-ring oxygen protonation; C, protonation to the bridge oxygen of the glycosidic bond for the glucosyl-oxygen cleavage; and D, protonation to that for the fructosyl-oxygen cleavage) gave the fragmentation. Paths B, C, and D were examined by the use of the sucrose molecule and H3O(+)(H2O)13. The path B needs a large activation energy, indicating that it is unlikely. The fragmentation transition state (TS1) of path C needs almost the same activation energy as that of path D. The isomerization TS of Int(C) → Int(D), TS(C → D), was also obtained as a bypass route. The present calculations showed that the path via the fructosyl-oxygen cleavage (D) is slightly (not absolutely) more favorable than that via the glucosyl-oxygen cleavage (C). PMID:23373870

  16. Investigation of the complex reaction coordinate of acid catalyzed amide hydrolysis from molecular dynamics simulations

    NASA Astrophysics Data System (ADS)

    Zahn, Dirk

    2004-05-01

    The rate-determining step of acid catalyzed peptide hydrolysis is the nucleophilic attack of a water molecule to the carbon atom of the amide group. Therein the addition of the hydroxyl group to the amide carbon atom involves the association of a water molecule transferring one of its protons to an adjacent water molecule. The protonation of the amide nitrogen atom follows as a separate reaction step. Since the nucleophilic attack involves the breaking and formation of several bonds, the underlying reaction coordinate is rather complex. We investigate this reaction step from path sampling Car-Parrinello molecular dynamics simulations. This approach does not require the predefinition of reaction coordinates and is thus particularly suited for investigating reaction mechanisms. From our simulations the most relevant components of the reaction coordinate are elaborated. Though the C⋯O distance of the oxygen atom of the water molecule performing the nucleophilic attack and the corresponding amide carbon atom is a descriptor of the reaction progress, a complete picture of the reaction coordinate must include all three molecules taking part in the reaction. Moreover, the proton transfer is found to depend on favorable solvent configurations. Thus, also the arrangement of non-reacting, i.e. solvent water molecules needs to be considered in the reaction coordinate.

  17. Solid acid catalysts pretreatment and enzymatic hydrolysis of macroalgae cellulosic residue for the production of bioethanol.

    PubMed

    Tan, Inn Shi; Lee, Keat Teong

    2015-06-25

    The aim of this study is to investigate the technical feasibility of converting macroalgae cellulosic residue (MCR) into bioethanol. An attempt was made to present a novel, environmental friendly and economical pretreatment process that enhances enzymatic conversion of MCR to sugars using Dowex (TM) Dr-G8 as catalyst. The optimum yield of glucose reached 99.8% under the optimal condition for solid acid pretreatment (10%, w/v biomass loading, 4%, w/v catalyst loading, 30min, 120°C) followed by enzymatic hydrolysis (45FPU/g of cellulase, 52CBU/g of β-glucosidase, 50°C, pH 4.8, 30h). The yield of sugar obtained was found more superior than conventional pretreatment process using H2SO4 and NaOH. Biomass loading for the subsequent simultaneous saccharification and fermentation (SSF) of the pretreated MCR was then optimized, giving an optimum bioethanol yield of 81.5%. The catalyst was separated and reused for six times, with only a slight drop in glucose yield.

  18. A potentiometric study of the hydrolysis of ethylenediaminetetraacetic acid to 150{degrees}C

    SciTech Connect

    Palmer, D.A.; Nguyen-Trung, Chinh

    1995-02-01

    Ethylenediaminetetraacetate anions, EDTA{sup 4-}, were titrated in a hydrogen-electrode concentration cell with an acidic titrant from 0 to 150{degrees}C at 25{degrees}C intervals. These titrations were carried out in the presence of 0. 1, 0.2, and 1.0 mol{center_dot}kg{sup -1} with the supporting electrolytes, sodium chloride, NaCl, and 1.0 mol{center_dot}kg{sup -1} tetramethylammonium trifluoromethylsulfonate, (CH{sub 3}){sub 4}N(F{sub 3}CSO{sub 3}) {l_brace}TMATFMS{r_brace} in order to assess the effect of both cation complexation by EDTA{sup 4-} and anion activity coefficient variations. The resulting hydrolysis quotients are discussed with reference to applications in boiler and heat exchanger chemical cleaning, as well as chemical and nuclear waste containment. Some recent diverse uses of this emf technique that also pertain to these applications will be mentioned briefly, e.g., surface absorption - zero-point-of-charge - measurements to high temperatures and in situ pH measurements in solubility and kinetic experiments.

  19. Solid acid catalysts pretreatment and enzymatic hydrolysis of macroalgae cellulosic residue for the production of bioethanol.

    PubMed

    Tan, Inn Shi; Lee, Keat Teong

    2015-06-25

    The aim of this study is to investigate the technical feasibility of converting macroalgae cellulosic residue (MCR) into bioethanol. An attempt was made to present a novel, environmental friendly and economical pretreatment process that enhances enzymatic conversion of MCR to sugars using Dowex (TM) Dr-G8 as catalyst. The optimum yield of glucose reached 99.8% under the optimal condition for solid acid pretreatment (10%, w/v biomass loading, 4%, w/v catalyst loading, 30min, 120°C) followed by enzymatic hydrolysis (45FPU/g of cellulase, 52CBU/g of β-glucosidase, 50°C, pH 4.8, 30h). The yield of sugar obtained was found more superior than conventional pretreatment process using H2SO4 and NaOH. Biomass loading for the subsequent simultaneous saccharification and fermentation (SSF) of the pretreated MCR was then optimized, giving an optimum bioethanol yield of 81.5%. The catalyst was separated and reused for six times, with only a slight drop in glucose yield. PMID:25839825

  20. Valorisation of food waste via fungal hydrolysis and lactic acid fermentation with Lactobacillus casei Shirota.

    PubMed

    Kwan, Tsz Him; Hu, Yunzi; Lin, Carol Sze Ki

    2016-10-01

    Food waste recycling via fungal hydrolysis and lactic acid (LA) fermentation has been investigated. Hydrolysates derived from mixed food waste and bakery waste were rich in glucose (80.0-100.2gL(-1)), fructose (7.6gL(-1)) and free amino nitrogen (947-1081mgL(-1)). In the fermentation with Lactobacillus casei Shirota, 94.0gL(-1) and 82.6gL(-1) of LA were produced with productivity of 2.61gL(-1)h(-1) and 2.50gL(-1)h(-1) for mixed food waste and bakery waste hydrolysate, respectively. The yield was 0.94gg(-1) for both hydrolysates. Similar results were obtained using food waste powder hydrolysate, in which 90.1gL(-1) of LA was produced with a yield and productivity of 0.92gg(-1) and 2.50gL(-1)h(-1). The results demonstrate the feasibility of an efficient bioconversion of food waste to LA and a decentralized approach of food waste recycling in urban area.

  1. Biopolymer from microbial assisted in situ hydrolysis of triglycerides and dimerization of fatty acids.

    PubMed

    Kavitha, V; Radhakrishnan, N; Madhavacharyulu, E; Sailakshmi, G; Sekaran, G; Reddy, B S R; Rajkumar, G Suseela; Gnanamani, Arumugam

    2010-01-01

    The present study demonstrates biopolymer production by in situ bio-based dimerization of fatty acids by microorganism isolated from marine sediments. Microbial isolate grown in Zobell medium in the presence of triglycerides for the period of 24-240 h at 37 degrees C, hydrolyze the applied triglycerides and sequentially dimerized the hydrolyzed products and subsequently polymerized and transformed to a biopolymer having appreciable adhesive properties. Physical (nature, odour, stickyness and tensile strength), chemical (instrumentation) and biochemical (cell free broth) methods of analyses carried out provided the hypotheses involved in the formation of the product as well as the nature of the product formed. Results revealed, lipolytic enzymes released during initial period of growth and the biosurfactant production during later period, respectively, hydrolyze the applied triglycerides and initiate the dimerization and further accelerated when the incubation period extended. The existence and the non-existence of in situ hydrolysis of various triglycerides followed by dimerization and polymerization and the mechanism of transformation of triglycerides to biopolymer are discussed in detail.

  2. Optimization of Serratia marcescens lipase production for enantioselective hydrolysis of 3-phenylglycidic acid ester.

    PubMed

    Gao, Li; Xu, Jian-He; Li, Xin-Jun; Liu, Zuo-Zhen

    2004-12-01

    Lipase production and cell growth of Serratia marcescens ECU1010 were optimized in shake flasks, with lipase production being enhanced 9.5-fold (4,780 U/l) compared with the initial activity (500 U/l). Optimal carbon and nitrogen sources were Tween-80 and peptone, and the optimal ratio of Tween-80 to peptone was 1:3. The optimized cultivation conditions were 25 degrees C and pH 6.5. Lipase activity, particularly specific activity, could be improved by decreasing the cultivation temperature from 35 to 25 degrees C. Enzyme stability was significantly improved by simple immobilization with synthetic adsorption resin no. 8244. After five reaction cycles, enzyme activity decreased only very slightly, while enantioselectivity of the preparation remained constant, and the ees (enantiomeric excess of the remaining substrate) achieved in all cases was higher than 97%. The resin-8244-lipase preparation can be used for efficient enantioselective hydrolysis of trans-3-(4'-methoxyphenyl)glycidic acid methyl ester [(+/-)-MPGM], a key intermediate in the synthesis of Diltiazem.

  3. Sequential acid and enzymatic hydrolysis in situ and bioethanol production from Gracilaria biomass.

    PubMed

    Wu, Fang-Chen; Wu, Jane-Yii; Liao, Yi-Jyun; Wang, Man-Ying; Shih, Ing-Lung

    2014-03-01

    Gracilaria sp., a red alga, was used as a feedstock for the production of bioethanol. Saccharification of Gracilaria sp. by sequential acid and enzyme hydrolysis in situ produced a high quality hydrolysate that ensured its fermentability to produce ethanol. The optimal saccharification process resulted in total 11.85g/L (59.26%) of glucose and galactose, Saccharomyces cerevisiae Wu-Y2 showed a good performance on co-fermentability of glucose and galactose released in the hydrolysate from Gracilaria sp. The final ethanol concentrations of 4.72g/L (0.48g/g sugar consumed; 94% conversion efficiency) and the ethanol productivity 4.93g/L/d were achieved. 1g of dry Gracilaria can be converted to 0.236g (23.6%) of bioethanol via the processes developed. Efficient alcohol production by immobilized S. cerevisiae Wu-Y2 in batch and repeated batch fermentation was also demonstrated. The findings of this study revealed that Gracilaria sp. can be a potential feedstock in biorefinery for ethanol production.

  4. The effect of pH on hydrolysis, cross-linking and barrier properties of starch barriers containing citric acid.

    PubMed

    Olsson, Erik; Menzel, Carolin; Johansson, Caisa; Andersson, Roger; Koch, Kristine; Järnström, Lars

    2013-11-01

    Citric acid cross-linking of starch for e.g. food packaging applications has been intensely studied during the last decade as a method of producing water-insensitive renewable barrier coatings. We managed to improve a starch formulation containing citric acid as cross-linking agent for industrial paper coating applications by adjusting the pH of the starch solution. The described starch formulations exhibited both cross-linking of starch by citric acid as well as satisfactory barrier properties, e.g. fairly low OTR values at 50% RH that are comparable with EVOH. Furthermore, it has been shown that barrier properties of coated papers with different solution pH were correlated to molecular changes in starch showing both hydrolysis and cross-linking of starch molecules in the presence of citric acid. Hydrolysis was shown to be almost completely hindered at solution pH≥4 at curing temperatures≤105 °C and at pH≥5 at curing temperatures≤150 °C, whereas cross-linking still occurred to some extent at pH≤6.5 and drying temperatures as low as 70 °C. Coated papers showed a minimum in water vapor transmission rate at pH 4 of the starch coating solution, corresponding to the point where hydrolysis was effectively hindered but where a significant degree of cross-linking still occurred.

  5. Volatile organic acid adsorption and cation dissociation by porphyritic andesite for enhancing hydrolysis and acidogenesis of solid food wastes.

    PubMed

    Cheng, Fan; Li, Ming; Li, Dawei; Chen, Ling; Jiang, Weizhong; Kitamura, Yutaka; Li, Baoming

    2010-07-01

    Volatile organic acid adsorption, cation dissociation by porphyritic andesite, and their effects on the hydrolysis and acidogenesis of solid food wastes were evaluated through batch experiments. The acetic acid adsorption experiments show that pH was mainly regulated by H(+) adsorption. The mono-layer and multi-layer adsorption were found under the low (8.3-83.2 mmol/L) and high (133.22-532.89 mmol/L) initial acetic acid concentration, respectively. The dissociated cations concentration in acidic solution showed the predominance of Ca(2+). Porphyritic andesite addition elevated the pH levels and accelerated hydrolysis and acidogenesis in the batch fermentation experiment. Leachate of porphyritic andesite addition achieved the highest hydrolysis constant of 22.1 x 10(-3)kgm(-2)d(-1) and VS degradation rates of 3.9 g L(-1)d(-1). The highest activity of microorganisms represented by specific growth rate of ATP, 0.16d(-1), and specific consumption rate of Ca(2+), 0.18d(-1), was obtained by adding leachate of porphyritic andesite.

  6. Volatile organic acid adsorption and cation dissociation by porphyritic andesite for enhancing hydrolysis and acidogenesis of solid food wastes.

    PubMed

    Cheng, Fan; Li, Ming; Li, Dawei; Chen, Ling; Jiang, Weizhong; Kitamura, Yutaka; Li, Baoming

    2010-07-01

    Volatile organic acid adsorption, cation dissociation by porphyritic andesite, and their effects on the hydrolysis and acidogenesis of solid food wastes were evaluated through batch experiments. The acetic acid adsorption experiments show that pH was mainly regulated by H(+) adsorption. The mono-layer and multi-layer adsorption were found under the low (8.3-83.2 mmol/L) and high (133.22-532.89 mmol/L) initial acetic acid concentration, respectively. The dissociated cations concentration in acidic solution showed the predominance of Ca(2+). Porphyritic andesite addition elevated the pH levels and accelerated hydrolysis and acidogenesis in the batch fermentation experiment. Leachate of porphyritic andesite addition achieved the highest hydrolysis constant of 22.1 x 10(-3)kgm(-2)d(-1) and VS degradation rates of 3.9 g L(-1)d(-1). The highest activity of microorganisms represented by specific growth rate of ATP, 0.16d(-1), and specific consumption rate of Ca(2+), 0.18d(-1), was obtained by adding leachate of porphyritic andesite. PMID:20156676

  7. Microbiological titration of proteins and of single amino acid content in biological materials without purification and hydrolysis.

    PubMed

    Puppo, S; Morpurgo, G; Nardi, S; Conti, G

    1978-04-01

    A method is described for the microbiological determination of the protein content of biological materials. This method can also be adopted to titrate the concentration of a single amino acid in the protein and has the following advantages: (1) titration can be done without purification and hydrolysis of proteins; (2) the titration graph is a straight line between 25 and 800 microgram/ml; (3) protein values agree with those obtained using the Kjeldhal method; and (4) each mutant requiring one amino acid may be used to titrate the concentration of a single amino acid of the protein. The leucine content of various kinds of flour was measured with this system.

  8. Structural Basis for Nucleotide Hydrolysis by the Acid Sphingomyelinase-like Phosphodiesterase SMPDL3A.

    PubMed

    Gorelik, Alexei; Illes, Katalin; Superti-Furga, Giulio; Nagar, Bhushan

    2016-03-18

    Sphingomyelin phosphodiesterase, acid-like 3A (SMPDL3A) is a member of a small family of proteins founded by the well characterized lysosomal enzyme, acid sphingomyelinase (ASMase). ASMase converts sphingomyelin into the signaling lipid, ceramide. It was recently discovered that, in contrast to ASMase, SMPDL3A is inactive against sphingomyelin and, surprisingly, can instead hydrolyze nucleoside diphosphates and triphosphates, which may play a role in purinergic signaling. As none of the ASMase-like proteins has been structurally characterized to date, the molecular basis for their substrate preferences is unknown. Here we report crystal structures of murine SMPDL3A, which represent the first structures of an ASMase-like protein. The catalytic domain consists of a central mixed β-sandwich surrounded by α-helices. Additionally, SMPDL3A possesses a unique C-terminal domain formed from a cluster of four α-helices that appears to distinguish this protein family from other phosphoesterases. We show that SMDPL3A is a di-zinc-dependent enzyme with an active site configuration that suggests a mechanism of phosphodiester hydrolysis by a metal-activated water molecule and protonation of the leaving group by a histidine residue. Co-crystal structures of SMPDL3A with AMP and α,β-methylene ADP (AMPCP) reveal that the substrate binding site accommodates nucleotides by establishing interactions with their base, sugar, and phosphate moieties, with the latter the major contributor to binding affinity. Our study provides the structural basis for SMPDL3A substrate specificity and sheds new light on the function of ASMase-like proteins. PMID:26792860

  9. L-lactic acid production from apple pomace by sequential hydrolysis and fermentation.

    PubMed

    Gullón, Beatriz; Yáñez, Remedios; Alonso, José Luis; Parajó, J C

    2008-01-01

    The potential of apple pomace (a solid waste from cider and apple juice making factories) as a source of sugars and other compounds for fermentation was evaluated. The effect of the cellulase-to-solid ratio (CSR) and the liquor-to-solid ratio (LSR) on the kinetics of glucose and total monosaccharide generation was studied. Mathematical models suitable for reproducing and predicting the hydrolyzate composition were developed. When samples of apple pomace were subjected to enzymatic hydrolysis, the glucose and fructose present in the raw material as free monosaccharides were extracted at the beginning of the process. Using low cellulase and cellobiase charges (8.5 FPU/g-solid and 8.5 IU/g-solid, respectively), 79% of total glucan was saccharified after 12 h, leading to solutions containing up to 43.8 g monosaccharides/L (glucose, 22.8 g/L; fructose, 14.8 g/L; xylose+mannose+galactose, 2.5 g/L; arabinose+rhamnose, 2.8g/L). These results correspond to a monosaccharide/cellulase ratio of 0.06 g/FPU and to a volumetric productivity of 3.65 g of monosaccharides/L h. Liquors obtained under these conditions were used for fermentative lactic acid production with Lactobacillus rhamnosus CECT-288, leading to media containing up to 32.5 g/L of L-lactic acid after 6 h (volumetric productivity=5.41 g/L h, product yield=0.88 g/g).

  10. Structural features of dilute acid, steam exploded, and alkali pretreated mustard stalk and their impact on enzymatic hydrolysis.

    PubMed

    Kapoor, Manali; Raj, Tirath; Vijayaraj, M; Chopra, Anju; Gupta, Ravi P; Tuli, Deepak K; Kumar, Ravindra

    2015-06-25

    To overcome the recalcitrant nature of biomass several pretreatment methodologies have been explored to make it amenable to enzymatic hydrolysis. These methodologies alter cell wall structure primarily by removing/altering hemicelluloses and lignin. In this work, alkali, dilute acid, steam explosion pretreatment are systematically studied for mustard stalk. To assess the structural variability after pretreatment, chemical analysis, surface area, crystallinity index, accessibility of cellulose, FT-IR and thermal analysis are conducted. Although the extent of enzymatic hydrolysis varies upon the methodologies used, nevertheless, cellulose conversion increases from <10% to 81% after pretreatment. Glucose yield at 2 and 72h are well correlated with surface area and maximum adsorption capacity. However, no such relationship is observed for xylose yield. Mass balance of the process is also studied. Dilute acid pretreatment is the best methodology in terms of maximum sugar yield at lower enzyme loading. PMID:25839820

  11. Structural features of dilute acid, steam exploded, and alkali pretreated mustard stalk and their impact on enzymatic hydrolysis.

    PubMed

    Kapoor, Manali; Raj, Tirath; Vijayaraj, M; Chopra, Anju; Gupta, Ravi P; Tuli, Deepak K; Kumar, Ravindra

    2015-06-25

    To overcome the recalcitrant nature of biomass several pretreatment methodologies have been explored to make it amenable to enzymatic hydrolysis. These methodologies alter cell wall structure primarily by removing/altering hemicelluloses and lignin. In this work, alkali, dilute acid, steam explosion pretreatment are systematically studied for mustard stalk. To assess the structural variability after pretreatment, chemical analysis, surface area, crystallinity index, accessibility of cellulose, FT-IR and thermal analysis are conducted. Although the extent of enzymatic hydrolysis varies upon the methodologies used, nevertheless, cellulose conversion increases from <10% to 81% after pretreatment. Glucose yield at 2 and 72h are well correlated with surface area and maximum adsorption capacity. However, no such relationship is observed for xylose yield. Mass balance of the process is also studied. Dilute acid pretreatment is the best methodology in terms of maximum sugar yield at lower enzyme loading.

  12. Catalysis of the hydrolysis of ethyl mandelate and esterification of alpha-bromopropionic acid by lipase in microemulsions.

    PubMed

    Xiao, H; Liu, J; Li, Z

    1993-01-01

    Candida cyclindracea lipase (CCL) was added to "sodium dodecyl sulfonate (AS)/n-butanol/n-octane/n-octane" water-in-oil microemulsion to catalyze the hydrolysis of ethyl mandelate and the esterification of alpha-bromopropionic acid with n-butanol, respectively. The catalytic activity of CCL in the above microemulsions was higher than that in the traditional oil/water biphasic systems. After hydrolysis for 48 h, the conversion rate of the reaction reached 90% and S-mandelic acid, [alpha]D20-149.8 (C10; H2O), optical purity ca. 97%, was isolated. While after esterification for 6 h, the conversion rate of the reaction reached 45%, and butyl-(R)-alpha-bromopropionate, [alpha]D20 18.2 (Cl; CHCl3), optical purity ca. 99%, was obtained.

  13. The Acid Hydrolysis Mechanism of Acetals Catalyzed by a Supramolecular Assembly in Basic Solution

    SciTech Connect

    Pluth, Michael D.; Bergman, Robert G.; Raymond, Kenneth N.

    2008-09-24

    A self-assembled supramolecular host catalyzes the hydrolysis of acetals in basic aqueous solution. The mechanism of hydrolysis is consistent with the Michaelis-Menten kinetic model. Further investigation of the rate limiting step of the reaction revealed a negative entropy of activation ({Delta}S{double_dagger} = -9 cal mol{sup -1}K{sup -1}) and an inverse solvent isotope effect (k(H{sub 2}O)/k(D{sub 2}O) = 0.62). These data suggest that the mechanism of hydrolysis that takes place inside the assembly proceeds through an A-2 mechanism, in contrast to the A-1 mechanism operating in the uncatalyzed reaction. Comparison of the rates of acetal hydrolysis in the assembly with the rate of the reaction of unencapsulated substrates reveals rate accelerations of up to 980 over the background reaction for the substrate diethoxymethane.

  14. Determination of DNA adducts by combining acid-catalyzed hydrolysis and chromatographic analysis of the carcinogen-modified nucleobases.

    PubMed

    Leung, Elvis M K; Deng, Kailin; Wong, Tin-Yan; Chan, Wan

    2016-01-01

    The commonly used method of analyzing carcinogen-induced DNA adducts involves the hydrolysis of carcinogen-modified DNA samples by using a mixture of enzymes, followed by (32)P-postlabeling or liquid chromatography (LC)-based analyses of carcinogen-modified mononucleotides/nucleosides. In the present study, we report the development and application of a new approach to DNA adduct analysis by combining the H(+)/heat-catalyzed release of carcinogen-modified nucleobases and the use of LC-based methods to analyze DNA adducts. Results showed that heating the carcinogen-modified DNA samples at 70 °C for an extended period of 4 to 6 h in the presence of 0.05% HCl can efficiently induce DNA depurination, releasing the intact carcinogen-modified nucleobases for LC analyses. After optimizing the hydrolysis conditions, DNA samples with C8- and N (2) -modified 2'-deoxyguanosine, as well as N (6) -modified 2'-deoxyadenosine, were synthesized by reacting DNA with 1-nitropyrene, acetaldehyde, and aristolochic acids, respectively. These samples were then hydrolyzed, and the released nucleobase adducts were analyzed using LC-based analytical methods. Analysis results demonstrated a dose-dependent release of target DNA adducts from carcinogen-modified DNA samples, indicating that the developed H(+)/heat-catalyzed hydrolysis method was quantitative. Comparative studies with enzymatic digestion method on carcinogen-modified DNA samples revealed that the two hydrolysis methods did not yield systematically different results.

  15. ESTIMATION OF HYDROLYSIS RATE CONSTANTS OF CARBOXYLIC ACID ESTER AND PHOSPHATE ESTER COMPOUNDS IN AQUEOUS SYSTEMS FROM MOLECULAR STRUCTURE BY SPARC

    EPA Science Inventory

    SPARC (SPARC Performs Automated Reasoning in Chemistry) chemical reactivity models were extended to calculate hydrolysis rate constants for carboxylic acid ester and phosphate ester compounds in aqueous non- aqueous and systems strictly from molecular structure. The energy diffe...

  16. Acid Catalysis in Basic Solution: A Supramolecular Host PromotesOrthoformate Hydrolysis

    SciTech Connect

    Pluth, Michael D.; Bergman, Robert G.; Raymond, Kenneth N.

    2007-12-12

    Though many enzymes can promote chemical reactions by tuning substrate properties purely through the electrostatic environment of a docking cavity, this strategy has proven challenging to mimic in synthetic host-guest systems. Here we report a highly-charged, water soluble, metal-ligand assembly with a hydrophobic interior cavity that thermodynamically stabilizes protonated substrates and consequently catalyzes the normally acidic hydrolysis of orthoformates in basic solution, with rate accelerations of up to 890-fold. The catalysis reaction obeys Michaelis-Menten kinetics, exhibits competitive inhibition, and the substrate scope displays size selectivity consistent with the constrained binding environment of the molecular host. Synthetic chemists have long endeavored to design host molecules capable of selectively binding slow-reacting substrates and catalyzing their chemical reactions. While synthetic catalysts are often site-specific and require certain properties of the substrate to insure catalysis, enzymes are often able to modify basic properties of the bound substrate such as pK{sub a} in order to enhance reactivity. Two common motifs used by nature to activate otherwise unreactive compounds are the precise arrangement of hydrogen-bonding networks and electrostatic interactions between the substrate and adjacent residues of the protein. Precise arrangement of hydrogen bonding networks near the active sites of proteins can lead to well-tuned pK{sub a}-matching, and can result in pK{sub a} shifts of up to eight units, as shown in bacteriorhodopsin. Similarly, purely electrostatic interactions can greatly favor charged states and have been responsible for pK{sub a} shifts of up to five units for acetoacetate decarboxylase. Attempts have been made to isolate the contributions of electrostatic versus covalent interactions to such pK{sub a} shifts; however this remains a difficult challenge experimentally. This challenge emphasizes the importance of synthesizing

  17. Production of nanocrystalline cellulose from an empty fruit bunches using sulfuric acid hydrolysis: Effect of reaction time on the molecular characteristics

    NASA Astrophysics Data System (ADS)

    Al-Dulaimi, Ahmed A.; R, Rohaizu; D, Wanrosli W.

    2015-06-01

    Nanocrystalline cellulose (NCC) was isolated from OPEFB pulp via sulfuric acid hydrolysis. The influence of reaction time to the molecular weight and surface charge of the NCC was investigated. Characterization of the product was carried out using zeta potential measurement and gel permeation chromatography test. Zeta potential measurement showed that the surface negative charge significantly increases with increasing reaction time. Gel permeation chromatography test indicates that molecular weight of NCC change variably with increasing of hydrolysis time. (Keywords: Nanocrystalline cellulose; acid hydrolysis; sulfate content; molecular weight)

  18. The rapid hydrolysis and efficient absorption of triglycerides with octanoic acid in the 1 and 3 positions and long-chain fatty acid in the 2 position.

    PubMed

    Jandacek, R J; Whiteside, J A; Holcombe, B N; Volpenhein, R A; Taulbee, J D

    1987-05-01

    We describe rapid hydrolysis of triglycerides with medium-chain fatty acids in the 1 and 3 positions and a long-chain fatty acid in the 2 position. The triglycerides, 2-linoleoyl-1,3-dioctanoyl glycerol (8L8) and 2-oleoyl-1,3-dioctanoyl glycerol, hydrolyzed more rapidly than triglycerides comprising all long-chain fatty acids. The in vitro hydrolysis rate of 8L8 was similar to that of a medium-chain triglyceride of octanoic and decanoic acids in random positions. From intestinal recovery of 14C 45 min after injection into the isolated, irrigated loop of the small intestine of an anesthetized rat, the amount of 2-[1-14C]linoleoyl-1,3-dioctanoyl glycerol absorbed was greater than 2 1/2 times that of its long-chain analog, 2-[1-14C]linoleoyl-1,3-dioleoyl glycerol. These data support the ease of hydrolysis and absorption of 1,3-dioctanoyl triglycerides with long-chain fatty acids in the 2 position.

  19. Isolation of bacterial cellulose nanocrystalline from pineapple peel waste: Optimization of acid concentration in the hydrolysis method

    NASA Astrophysics Data System (ADS)

    Anwar, Budiman; Rosyid, Nurul Huda; Effendi, Devi Bentia; Nandiyanto, Asep Bayu Dani; Mudzakir, Ahmad; Hidayat, Topik

    2016-02-01

    Isolation of needle-shaped bacterial cellulose nanocrystalline with a diameter of 16-64 nm, a fiber length of 258-806 nm, and a degree of crystallinity of 64% from pineapple peel waste using an acid hydrolysis process was investigated. Experimental showed that selective concentration of acid played important roles in isolating the bacterial cellulose nanocrystalline from the cellulose source. To achieve the successful isolation of bacterial cellulose nanocrystalline, various acid concentrations were tested. To confirm the effect of acid concentration on the successful isolation process, the reaction conditions were fixed at a temperature of 50°C, a hydrolysis time of 30 minutes, and a bacterial cellulose-to-acid ratio of 1:50. Pineapple peel waste was used as a model for a cellulose source because to the best of our knowledge, there is no report on the use of this raw material for producing bacterial cellulose nanocrystalline. In fact, this material can be used as an alternative for ecofriendly and cost-free cellulose sources. Therefore, understanding in how to isolate bacterial cellulose nanocrystalline from pineapple peel waste has the potential for large-scale production of inexpensive cellulose nanocrystalline.

  20. Positional specificity of gastric hydrolysis of long-chain n-3 polyunsaturated fatty acids of seal milk triglycerides.

    PubMed

    Iverson, S J; Sampugna, J; Oftedal, O T

    1992-11-01

    Long-chain n-3 polyunsaturated fatty acids (n-3 PUFA) of marine oils are important dietary components for both infants and adults, and are incorporated into milks following maternal dietary intake. However, little is known about the hydrolysis of these PUFA from milk triglycerides (TG) by lipases in suckling young. Seals, like humans, possess gastric lipase; however, the milk lipids of seals and sea lions are almost devoid of the readily hydrolyzable medium-chain fatty acids, and are characterized by a large percentage (10-30%) of n-3 PUFA. Gastric hydrolysis of milk lipids was studied in vivo in suckling pups of three species (the California sea lion, the harp seal and the hooded seal) in order to elucidate the actions and specificity of gastric lipases on milk TG in relation to fatty acid composition and TG structure. Regardless of milk fat content (31-61% fat) or extent of gastric hydrolysis (10-56%), the same fatty acids were preferentially released in all three species, as determined by their relative enrichment in the free fatty acid (FFA) fraction. In addition to 16:1 and 18:0, these were the PUFA of 18 carbons and longer, except for 22:6n-3. Levels of 20:5n-3 were most notably enriched in FFA, at up to five times that found in the TG. Although 22:6n-3 was apparently also released from the TG (reduced in the diglyceride), it was also notably reduced in FFA.(ABSTRACT TRUNCATED AT 250 WORDS)

  1. Hydrolysis of Cellulose by a Mesoporous Carbon-Fe₂(SO₄)₃/γ-Fe₂O₃ Nanoparticle-Based Solid Acid Catalyst.

    PubMed

    Yamaguchi, Daizo; Watanabe, Koki; Fukumi, Shinya

    2016-01-01

    Carbon-based solid acid catalysts have shown significant potential in a wide range of applications, and they have been successfully synthesized using simple processes. Magnetically separable mesoporous carbon composites also have enormous potential, especially in separation and adsorption technology. However, existing techniques have been unable to produce a magnetically separable mesoporous solid acid catalyst because no suitable precursors have been identified. Herein we describe a magnetically separable, mesoporous solid acid catalyst synthesized from a newly developed mesoporous carbon-γ-Fe2O3 nanoparticle composite. This material exhibits an equivalent acid density and catalytic activity in the hydrolysis of microcrystalline cellulose, to that of the cellulose-derived conventional catalyst. Since it is magnetically separable, this material can be readily recovered and reused, potentially reducing the environmental impact of industrial processes to which it is applied. PMID:26856604

  2. Kinetic and Modeling Investigation to Provide Design Guidelines for the NREL Dilute-Acid Process Aimed at Total Hydrolysis/Fractionation of Lignocellulosic Biomass: July 1998

    SciTech Connect

    Lee, Y. Y.; Iyer, P.; Xiang, Q.; Hayes, J.

    2004-08-01

    Following up on previous work, subcontractor investigated three aspects of using NREL ''pretreatment'' technology for total hydrolysis (cellulose as well as hemicellulose) of biomass. Whereas historic hydrolysis of biomass used either dilute acid or concentrated acid technology for hydrolysis of both hemicellulose and cellulose, NREL has been pursuing very dilute acid hydrolysis of hemicellulose followed by enzymatic hydrolysis of cellulose. NREL's countercurrent shrinking-bed reactor design for hemicellulose hydrolysis (pretreatment) has, however, shown promise for total hydrolysis. For the first task, subcontractor developed a mathematical model of the countercurrent shrinking bed reactor operation and, using yellow poplar sawdust as a feedstock, analyzed the effect of: initial solid feeding rate, temperature, acid concentration, acid flow rate, Peclet number (a measure of backmixing in liquid flow), and bed shrinking. For the second task, subcontractor used laboratory trials, with yellow poplar sawdust and 0.07 wt% sulfuric acid at various temperatures, to verify the hydrolysis of cellulose to glucose (desired) and decomposition of glucose (undesired) and determine appropriate parameters for use in kinetic models. Unlike cellulose and hemicellulose, lignins, the third major component of biomass, are not carbohydrates that can be broken down into component sugars. They are, however, aromatic complex amorphous phenolic polymers that can likely be converted into low-molecular weight compounds suitable for production of fuels and chemicals. Oxidative degradation is one pathway for such conversion and hydrogen peroxide would be an attractive reagent for this, as it would leave no residuals. For the third task, subcontractor reacted lignin with hydrogen peroxide under various conditions and analyzed the resulting product mix.

  3. Cholesterol efflux from THP-1 macrophages is impaired by the fatty acid component from lipoprotein hydrolysis by lipoprotein lipase.

    PubMed

    Yang, Yanbo; Thyagarajan, Narmadaa; Coady, Breanne M; Brown, Robert J

    2014-09-01

    Lipoprotein lipase (LPL) is an extracellular lipase that primarily hydrolyzes triglycerides within circulating lipoproteins. Macrophage LPL contributes to atherogenesis, but the mechanisms behind it are poorly understood. We hypothesized that the products of lipoprotein hydrolysis generated by LPL promote atherogenesis by inhibiting the cholesterol efflux ability by macrophages. To test this hypothesis, we treated human THP-1 macrophages with total lipoproteins that were hydrolyzed by LPL and we found significantly reduced transcript levels for the cholesterol transporters ATP binding cassette transporter A1 (ABCA1), ABCG1, and scavenger receptor BI. These decreases were likely due to significant reductions for the nuclear receptors liver-X-receptor-α, peroxisome proliferator activated receptor (PPAR)-α, and PPAR-γ. We prepared a mixture of free fatty acids (FFA) that represented the ratios of FFA species within lipoprotein hydrolysis products, and we found that the FFA mixture also significantly reduced cholesterol transporters and nuclear receptors. Finally, we tested the efflux of cholesterol from THP-1 macrophages to apolipoprotein A-I, and we found that the treatment of THP-1 macrophages with the FFA mixture significantly attenuated cholesterol efflux. Overall, these data show that the FFA component of lipoprotein hydrolysis products generated by LPL may promote atherogenesis by inhibiting cholesterol efflux, which partially explains the pro-atherogenic role of macrophage LPL.

  4. Cholesterol efflux from THP-1 macrophages is impaired by the fatty acid component from lipoprotein hydrolysis by lipoprotein lipase.

    PubMed

    Yang, Yanbo; Thyagarajan, Narmadaa; Coady, Breanne M; Brown, Robert J

    2014-09-01

    Lipoprotein lipase (LPL) is an extracellular lipase that primarily hydrolyzes triglycerides within circulating lipoproteins. Macrophage LPL contributes to atherogenesis, but the mechanisms behind it are poorly understood. We hypothesized that the products of lipoprotein hydrolysis generated by LPL promote atherogenesis by inhibiting the cholesterol efflux ability by macrophages. To test this hypothesis, we treated human THP-1 macrophages with total lipoproteins that were hydrolyzed by LPL and we found significantly reduced transcript levels for the cholesterol transporters ATP binding cassette transporter A1 (ABCA1), ABCG1, and scavenger receptor BI. These decreases were likely due to significant reductions for the nuclear receptors liver-X-receptor-α, peroxisome proliferator activated receptor (PPAR)-α, and PPAR-γ. We prepared a mixture of free fatty acids (FFA) that represented the ratios of FFA species within lipoprotein hydrolysis products, and we found that the FFA mixture also significantly reduced cholesterol transporters and nuclear receptors. Finally, we tested the efflux of cholesterol from THP-1 macrophages to apolipoprotein A-I, and we found that the treatment of THP-1 macrophages with the FFA mixture significantly attenuated cholesterol efflux. Overall, these data show that the FFA component of lipoprotein hydrolysis products generated by LPL may promote atherogenesis by inhibiting cholesterol efflux, which partially explains the pro-atherogenic role of macrophage LPL. PMID:25130461

  5. A new sunscreen of the cinnamate class: synthesis and enzymatic hydrolysis evaluation of glyceryl esters of p-methoxycinnamic acid.

    PubMed

    de Freitas, Zaida Maria Faria; dos Santos, Elisabete Pereira; da Rocha, João Ferreira; Dellamora-Ortiz, Gisela Maria; Gonçalves, José Carlos Saraiva

    2005-05-01

    Glyceryl esters of p-methoxycinnamic acid, 1,3-dipalmitoyl-2-p-methoxycinnamoyl-1,2,3-propanetriol and 1,3-dioctanoyl-2-p-methoxycinnamoyl-1,2,3-propanetriol were synthesised in an attempt to increase substantivity and decrease eventual undesirable effects of sunscreens of this class. To assess if the glyceryl esters could present a higher stability towards hydrolysis by lipases in the stratum corneum, hydrolysis rates were determined in vitro using a commercial fungal lipase from Rhizomucor miehei. Results presented herein show that the glyceryl esters have similar lambda(max) and epsilon values to sunscreens of the cinnamate class. The ester 1,3-dipalmitoyl-2-p-methoxycinnamoyl-1,2,3-propanetriol presented a 2.8 times lower hydrolysis rate by lipase, in vitro, than the commercial sunscreen 2-ethylhexyl-p-methoxycinnamate (alkyl ester). This finding suggests that this triacylglycerol can possibly have a longer retention time in the skin and consequently promote a more intense and effective antisolar action than the commercial sunscreen.

  6. Cooperative effect of water molecules in the self-catalyzed neutral hydrolysis of isocyanic acid: a comprehensive theoretical study.

    PubMed

    Wei, Xi-Guang; Sun, Xiao-Ming; Wu, Xiao-Peng; Geng, Song; Ren, Yi; Wong, Ning-Bew; Li, Wai-Kee

    2011-08-01

    The detailed reaction mechanism for the water-assisted hydrolysis of isocyanic acid, HNCO + (n + 1) H(2)O → CO(2) + NH(3) + nH(2)O (n = 0-6), taking place in the gas phase, has been investigated. All structures were optimized and characterized at the MP2/6-31 + G level of theory, and then re-optimized at MP2/6-311++G. The seven explicit water molecules participating in the hydrolysis can be divided into two groups, one directly involved in the proton relay, and the other located in the vicinity of the substrate playing the cooperative role by engaging in hydrogen-bonding to HN = C = O. Two possible reaction pathways, the addition of water molecule across the C = N bond or across the C = O bond, are discussed, and the former is proved to be more favorable energetically. Our calculations suggest that, in the most kinetically favorable pathway for the titled hydrolysis, three water molecules are directly participating in the hydrogen transfer via an eight-membered cyclic transition state, while the other four water molecules catalyze the hydrolysis of HN = C = O by forming three eight-membered cooperative loops near the substrate. This strain-free hydrogen-bond network leads to the best estimated rate-determining activation energy of 24.9 kJ mol(-1) at 600 K, in excellent agreement with the gas-phase kinetic experimental result, 25.8 kJ mol(-1). PMID:21161555

  7. Highly Amino Acid Selective Hydrolysis of Myoglobin at Aspartate Residues as Promoted by Zirconium(IV)-Substituted Polyoxometalates.

    PubMed

    Ly, Hong Giang T; Absillis, Gregory; Janssens, Rik; Proost, Paul; Parac-Vogt, Tatjana N

    2015-06-15

    SDS-PAGE/Edman degradation and HPLC MS/MS showed that zirconium(IV)-substituted Lindqvist-, Keggin-, and Wells-Dawson-type polyoxometalates (POMs) selectively hydrolyze the protein myoglobin at Asp-X peptide bonds under mildly acidic and neutral conditions. This transformation is the first example of highly sequence selective protein hydrolysis by POMs, a novel class of protein-hydrolyzing agents. The selectivity is directed by Asp residues located on the surface of the protein and is further assisted by electrostatic interactions between the negatively charged POMs and positively charged surface patches in the vicinity of the cleavage site.

  8. Enhanced enzymatic hydrolysis of poplar bark by combined use of gamma ray and dilute acid for bioethanol production

    NASA Astrophysics Data System (ADS)

    Chung, Byung Yeoup; Lee, Jae Taek; Bai, Hyoung-Woo; Kim, Ung-Jin; Bae, Hyeun-Jong; Gon Wi, Seung; Cho, Jae-Young

    2012-08-01

    Pretreatment of poplar bark with a combination of sulfuric acid (3%, w/w, H2SO4) and gamma irradiation (0-1000 kGy) was performed in an attempt to enhance enzymatic hydrolysis for bioethanol production. The yields of reducing sugar were slightly increased with an increasing irradiation dose, ranging from 35.4% to 51.5%, with a 56.1% reducing sugar yield observed after dilute acid pretreatment. These results clearly showed that soluble sugars were released faster and to a greater extent in dilute acid-pretreated poplar bark than in gamma irradiation-pretreated bark. When combined pretreatment was carried out, a drastic increase in reducing sugar yield (83.1%) was found compared with individual pretreatment, indicating the possibility of increasing the convertibility of poplar bark following combined pretreatment. These findings are likely associated with cellulose crystallinity, lignin modification, and removal of hemicelluloses.

  9. The hydrolysis of polyimides

    NASA Technical Reports Server (NTRS)

    Hoagland, P. D.; Fox, S. W.

    1973-01-01

    Thermal polymerization of aspartic acid produces a polysuccinimide (I), a chain of aspartoyl residues. An investigation was made of the alkaline hydrolysis of the imide rings of (I) which converts the polyimide to a polypeptide. The alkaline hydrolysis of polyimides can be expected to be kinetically complex due to increasing negative charge generated by carboxylate groups. For this reason, a diimide, phthaloyl-DL-aspartoyl-beta-alanine (IIA) was synthesized for a progressive study of the hydrolysis of polyimides. In addition, this diimide (IIA) can be related to thalidomide and might be expected to exhibit similar reactivity during hydrolysis of the phthalimide ring.

  10. Simultaneous determination of acetylsalicylic acid and salicylic acid in human plasma by isocratic high-pressure liquid chromatography with post-column hydrolysis and fluorescence detection.

    PubMed

    Hobl, Eva-Luise; Jilma, Bernd; Ebner, Josef; Schmid, Rainer W

    2013-06-01

    A selective, sensitive and rapid high-performance liquid chromatography method with post-column hydrolysis and fluorescence detection was developed for the simultaneous quantification of acetylsalicylic acid and its metabolite salicylic acid in human plasma. Following the addition of 2-hydroxy-3-methoxybenzoic acid as internal standard and simple protein precipitation with acetonitrile, the analytes were separated on a ProntoSIL 120 C18 ace-EPS column (150 × 2 mm, 3 µm) protected by a C8 guard column (5 µm). The mobile phase, 10 mm formic acid in water (pH 2.9) and acetonitrile (70:30, v/v), was used at a flow rate of 0.35 mL/min. After on-line post-column hydrolysis of acetylsalicylic acid (ASA) to salicylic acid (SA) by addition of alkaline solution, the analytes were measured at 290 nm (λex ) and 400 nm (λem ). The method was linear in the concentration ranges between 0.05 and 20 ng/μL for both ASA and SA with a lower limit of quantification of 25 pg/μL for SA and 50 pg/μL for ASA. The limit of detection was 15 pg/μL for SA and 32.5 pg/μL for ASA. The analysis of ASA and SA can be carried out within 8 min; therefore this method is suitable for measuring plasma concentrations of salicylates in clinical routine.

  11. The fatty-acid amide hydrolase inhibitor URB597 does not affect triacylglycerol hydrolysis in rat tissues.

    PubMed

    Clapper, Jason R; Duranti, Andrea; Tontini, Andrea; Mor, Marco; Tarzia, Giorgio; Piomelli, Daniele

    2006-11-01

    The O-arylcarbamate URB597 (cyclohexylcarbamic acid 3'-carbamoylbiphenyl-3-yl ester; also referred to as KDS-4103) is a potent inhibitor of fatty-acid amide hydrolase (FAAH), an intracellular serine hydrolase responsible for the inactivation of the endogenous cannabinoid anandamide. URB597 demonstrates a remarkable degree of selectivity for FAAH over other serine hydrolases (e.g. cholinesterases) or other components of the endocannabinoid system (e.g. cannabinoid receptors). However, in a proteomic-based selectivity screen based on the displacement of fluorophosphonate-rhodamine (FPR) from mouse brain proteins, it was recently shown that URB597 prevents FPR binding to triacylglycerol hydrolase (TGH) with a median inhibitory concentration of 192nM. To determine whether this effect correlates with inhibition of TGH activity, we investigated the ability of URB597 to inhibit triolein hydrolysis in rat liver and heart tissues, which are rich in TGH, as well as white adipose tissue (WAT), which is rich in adipose triacylglycerol lipase (TGL) and hormone-sensitive lipase. The results show that URB597 does not affect triolein hydrolysis in any of these tissues at concentrations as high as 10microM, whereas it inhibits FAAH activity at low nanomolar concentrations. Moreover, intraperitoneal (i.p.) administration of URB597 at doses that maximally inhibit FAAH in vivo (0.3-3mgkg(-1)) exerts no effect on triolein hydrolysis and tissue triacylglycerol (TAG) levels in rat liver, heart or WAT. The results indicate that URB597, while potent at inhibiting FAAH, does not affect TGH and TGL activities in rat tissues.

  12. Release and degradation of anthocyanins and phenolics from blueberry pomace during thermal acid hydrolysis and dry heating.

    PubMed

    Bener, Mustafa; Shen, Yixiao; Apak, Reşat; Finley, John W; Xu, Zhimin

    2013-07-10

    In this study, blueberry pomace was soaked in pH 1, 4, or 7 solution for 10 min followed by boiling hydrolysis. Nine anthocyanins and 11 other phenolic compounds were released after acid hydrolysis. The highest anthocyanin release (4.70 mg/g) was achieved by boiling at pH 1 for 15 min followed by 3.94 mg/g at pH 4 and 3.46 mg/g at pH 7. Phenolics were released more quickly than anthocyanins during boiling. The change of antioxidant activity of the pomace during boiling was correlated with the total phenolic content but not anthocyanin content. The degradation rate of anthocyanins during boiling eventually surpassed the release rate from the pomace. Protocatechuic acid and catechin continuously increased during heating. Dry heat resulted in continuous degradation of anthocyanins and other phenolics in the pomace. The reduction in antioxidant activity of the pomace during dry heating was correlated with both the phenolic and anthocyanin contents.

  13. Effect of acid hydrolysis combined with heat moisture treatment on structure and physicochemical properties of corn starch.

    PubMed

    Sun, Qingjie; Zhu, Xiaolei; Si, Fumei; Xiong, Liu

    2015-01-01

    Modification of starch led to new products with new desirable properties. Corn starch samples modified by acid hydrolysis combined with heat moisture treatment (AH-HMT) were made by changing pH, moisture content and treated temperature. After modification, swelling power at temperature higher than 75 °C of corn starches decreased while solubility of the starches increased. After AH-HMT, pasting temperature (PT) of all treated starch samples increased. But lower peak viscosity (PKV), trough viscosity (TV) and break down (BD) of most treated starch samples were observed. AH-HMT increased the gel hardness of all treated starches. And the biggest hardness of modified starch gel was 148.419 g, improving 93.471 g compared with native starch gel. The melting temperatures (To, Tp, Tc) of modified starch increased, but the melting range and △H decreased. The X-ray pattern remained practically unchanged with or without AH-HMT. Acid hydrolysis combined with heat moisture treatment (AH-HMT) improved the functional properties of corn starch. PMID:25593372

  14. Interaction between amylose and 1-butanol during 1-butanol-hydrochloric acid hydrolysis of normal rice starch.

    PubMed

    Hu, Xiuting; Wei, Benxi; Zhang, Bao; Li, Hongyan; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

    2013-10-01

    The aim of this study was to examine the interaction between amylose and 1-butanol during the 1-butanol-hydrochloric acid (1-butanol-HCl) hydrolysis of normal rice starch. The interaction model between amylose and 1-butanol was proposed using gas chromatography-mass spectrometry (GC-MS), (13)C cross polarization and magic angle spinning NMR analysis ((13)C CP/MAS NMR), differential scanning calorimetry (DSC), and thermalgravimetric analysis (TGA). GC-MS data showed that another form of 1-butanol existed in 1-butanol-HCl-hydrolyzed normal rice starch, except in the form of free molecules absorbed on the starch granules. The signal of 1-butanol-HCl-hydrolyzed starch at 100.1 ppm appeared in the (13)C CP/MAS NMR spectrum, indicating that the amylose-1-butanol complex was formed. DSC and TGA data also demonstrated the formation of the complex, which significantly affected the thermal properties of normal rice starch. These findings revealed that less dextrin with low molecular weight formed might be attributed to resistance of this complex to acid during 1-butanol-HCl hydrolysis.

  15. Determination of polyadipates migrating from lid gaskets of glass jars. Hydrolysis to adipic acid and measurement by LC-MS/MS.

    PubMed

    Driffield, M; Bradley, E L; Harmer, N; Castle, L; Klump, S; Mottier, P

    2010-10-01

    Polyadipate plasticizers can be present in the polyvinylchloride (PVC) gaskets used to seal the lids of glass jars. As the gaskets can come into direct contact with the foodstuffs inside the jar, the potential exists for polyadipate migration into the food. The procedure and performance characteristics of a test method for the analysis of polyadipates in food simulants (3% aqueous acetic acid and 10% aqueous ethanol) and the volatile test media used in substitute fat tests (isooctane and 95% aqueous ethanol) are described. The PVC gaskets were exposed to the food simulants or their substitutes under standard test conditions. Studies were initially carried out using direct measurement of the polyadipate oligomers by liquid chromatography with time-of-flight mass spectrometric detection (LC-TOF-MS) but this was not practical due to the number of peaks detected. Instead, the migrating polyadipates were hydrolysed to adipic acid and measured by liquid chromatography with tandem mass spectrometric detection (LC-MS/MS). The amount of polyadipate that this measurement of adipic acid represents was then calculated. Method performance was assessed by analysis of gaskets from two types of jar lids by single-laboratory validation. Linearity, sensitivity, repeatability, intermediate reproducibility and recovery were determined to be suitable for checking compliance with the 30 mg/kg specific migration limits for polyesters of 1,2-propane diol and/or 1,3- and/or 1,4-butanediol and/or polypropylene-glycol with adipic acid, which may be end-capped with acetic acid or fatty acids C(12)-C(18) or n-octanol and/or n-decanol. The method was found to be much quicker than previous methods involving extraction, clean-up, hydrolysis, esterification, derivatisation and GC measurement, consequently saving time and money.

  16. Redox cycles of vitamin E: Hydrolysis and ascorbic acid dependent reduction of 8a-(alkyldioxy)tocopherones

    SciTech Connect

    Liebler, D.C.; Kaysen, K.L.; Kennedy, T.A. )

    1989-12-12

    Oxidation of the biological antioxidant {alpha}-tocopherol (vitamin E; TH) by peroxyl radicals yields 8a-(alkyldioxy)tocopherones, which either may hydrolyze to {alpha}-tocopheryl quinone (TQ) or may be reduced by ascorbic acid to regenerate TH. To define the chemistry of this putative two-electron TH redox cycle, we studied the hydrolysis and reduction of 8a-((2,4-dimethyl-1-nitrilopent-2-yl)dioxyl)tocopherone (1) in acetonitrile/buffer mixtures and in phospholipid liposomes. TQ formation in acetonitrile/buffer mixtures, which was monitored spectrophotometrically, declined with increasing pH and could not be detected above pH 4. The rate of TQ formation from 1 first increased with time and then decreased in a first-order terminal phase. Rearrangement of 8a-hydroxy-{alpha}-tocopherone (2) to TQ displayed first-order kinetics identical with the terminal phase for TQ formation from 1. Both rate constants increased with decreasing pH. Hydrolysis of 1 in acetonitrile/H{sub 2}{sup 18}O yielded ({sup 18}O)TQ. These observations suggest that 1 loses the 8a-(alkyldioxy) moiety to produce the tocopherone cation (T{sup +}), which hydrolyzes to 2, the TQ-forming intermediate. Incubation of either 1 or 2 with ascorbic acid in acetonitrile/buffer yielded TH. Reduction of both 1 and 2 decreased with increasing pH. In phosphatidylcholine liposomes at pH 7, approximately 10% of the T{sup +} generated from 1 was reduced to TH by 5 mM ascorbic acid. The results collectively demonstrate that T{sup +} is the ascorbic acid reducible intermediate in a two-electron TH redox cycle, a process that probably would require biocatalysis to proceed in biological membranes.

  17. Effect of high dry solids loading on enzymatic hydrolysis of acid bisulfite pretreated Eastern redcedar.

    PubMed

    Ramachandriya, Karthikeyan D; Wilkins, Mark; Atiyeh, Hasan K; Dunford, Nurhan T; Hiziroglu, Salim

    2013-11-01

    This study investigates hydrolysis of cellulose from Eastern redcedar to glucose at high solids loading. Enzymatic hydrolysis of pretreated redcedar was performed with 0.5 ml Accelerase® 1500/g glucan (46 FPU/g glucan) using dry solids loading from 2% to 20% (w/w). Rheological challenges observed at high solids loading were overcome by adding stainless steel balls to shake flask reactors. The highest glucose concentration, 126 g/L (84% glucan-to-glucose yield), was obtained using 20% solids loading with stainless steel balls as a mixing aid. This enzymatic hydrolyzate was fermented into ethanol using Saccharomyces cerevisiae D5A to produce 52 g/L of ethanol (corresponding to 166 L/dry Mg of redcedar). Reducing enzyme dosage at 16% solids loading from 46 to 11.5 FPU/g glucan reduced glucan-to-glucose yields. This study has demonstrated the possibility of extracting sugars from the invasive species of Eastern redcedar with high solid loadings and their conversion into ethanol.

  18. Fundamental study of the mechanism and kinetics of cellulose hydrolysis by acids and enzymes

    NASA Astrophysics Data System (ADS)

    Gong, C. S.; Chang, M.

    1981-02-01

    There are three basic enzymes e.g., endoglucanase (C/sub x/), exoglucanase (C1) and cellobiase comprising the majority of extracellular cellulase enzymes produced by the cellulolytic mycelial fungi, Trichoderma reesei, and other cellulolytic microorganisms. The kinetics of cellobiase were developed on the basis of applying the pseudo-steady state assumption to hydrolyze cellobiose to glucose. The results indicated that cellobiase was bjected to end-product inhibition by glucose. The kinetic modeling of exoglucanase (C1) with respect to cellodextrins was studied. Both glucose and cellobiose were found to be inhibitors of this enzyme with cellobiose being a stronger inhibitor than glucose. Similarly, endoglucanase (C/sub x) is subject to end-product inhibition by glucose. Crystallinity of the cellulose affects the rate of hydrolysis by cellulases. Hence, the changes in crystallinity of cellulose in relation to chemical pretreatment and enzyme hydrolysis was compared. The study of cellulase biosynthesis resulted in the conclusion that exo-and endo-glucanases are coinduced while cellobiase is synthesized independent of the other two enzymes.

  19. An integrated process for the production of platform chemicals and diesel miscible fuels by acid-catalyzed hydrolysis and downstream upgrading of the acid hydrolysis residues with thermal and catalytic pyrolysis.

    PubMed

    Girisuta, Buana; Kalogiannis, Konstantinos G; Dussan, Karla; Leahy, James J; Hayes, Michael H B; Stefanidis, Stylianos D; Michailof, Chrysa M; Lappas, Angelos A

    2012-12-01

    This study evaluates an integrated process for the production of platform chemicals and diesel miscible biofuels. An energy crop (Miscanthus) was treated hydrothermally to produce levulinic acid (LA). Temperatures ranging between 150 and 200 °C, sulfuric acid concentrations 1-5 wt.% and treatment times 1-12 h were applied to give different combined severity factors. Temperatures of 175 and 200 °C and acid concentration of 5 wt.% were found to be necessary to achieve good yield (17 wt.%) and selectivities of LA while treatment time did not have an effect. The acid hydrolysis residues were characterized for their elemental, cellulose, hemicellulose and lignin contents, and then tested in a small-scale pyrolyzer using silica sand and a commercial ZSM-5 catalyst. Milder pretreatment yielded more oil (43 wt.%) and oil O(2) (37%) while harsher pretreatment and catalysis led to more coke production (up to 58 wt.%), less oil (12 wt.%) and less oil O(2) (18 wt.%).

  20. In situ pressurized biphase acid hydrolysis, a promising approach to produce bioactive diosgenin from the tubers of Dioscorea Zingiberensis

    PubMed Central

    Yang, Huan; Yin, Hua-wu; Wang, Xue-wei; Li, Zi-hao; Shen, Yu-ping; Jia, Xiao-bin

    2015-01-01

    Background: The tubers of Dioscorea zingiberensis, is the most favorable plant material for the production of diosgenin, an important bioactive steroidal sapogenin and requisite precursor of cortin, contraceptive and sex hormone, which is the only desired product after steroidal saponins from the tubers are hydrolyzed. Objective: A novel technology, in situ pressurized biphase acid hydrolysis was constructed for the first time to simplify extraction process, increase extraction yield and decrease the consumption of mineral acids. Materials and Methods: The method developed in this study has been optimized and verified through orthogonal design for experiments, in which the effect and their significance of four factors including molarity of acid, temperature, extraction duration and sample quantity have been investigated. Then, the comparison was conducted among the newly developed method and other reported methods. The diosgenin was also isolated by column chromatography, followed by mass spectrometry and nuclear magnetic resonance analysis for structural confirmation. Results: It was found that temperature is the factor of the most influence and the highest extraction yield at 2.21% has been achieved while the hydrolysis was performed at 140°C for 1.5 h in 0.20M H2SO4 solution with petroleum ether under an uncontrolled pressurized condition. And, compared to the others, the increment in the extraction yield of new method was 20.8 ~ 74.0%, and the consumption of H2SO4 was reduced by 17 times at most. Conclusion: This method is a much cleaner and more efficient approach for extraction of diosgenin from the tubers, and is promising to be applied in pharmaceutical industry. PMID:26246743

  1. AMP kinase activation with AICAR further increases fatty acid oxidation and blunts triacylglycerol hydrolysis in contracting rat soleus muscle.

    PubMed

    Smith, Angela C; Bruce, Clinton R; Dyck, David J

    2005-06-01

    Muscle contraction increases glucose uptake and fatty acid (FA) metabolism in isolated rat skeletal muscle, due at least in part to an increase in AMP-activated kinase activity (AMPK). However, the extent to which AMPK plays a role in the regulation of substrate utilization during contraction is not fully understood. We examined the acute effects of 5-aminoimidazole-4-carboxamide riboside (AICAR; 2 mm), a pharmacological activator of AMPK, on FA metabolism and glucose oxidation during high intensity tetanic contraction in isolated rat soleus muscle strips. Muscle strips were exposed to two different FA concentrations (low fatty acid, LFA, 0.2 mm; high fatty acid, HFA, 1 mm) to examine the role that FA availability may play in both exogenous and endogenous FA metabolism with contraction and AICAR. Synergistic increases in AMPK alpha2 activity (+45%; P<0.05) were observed after 30 min of contraction with AICAR, which further increased exogenous FA oxidation (LFA: +71%, P<0.05; HFA: +46%, P<0.05) regardless of FA availability. While there were no changes in triacylglycerol (TAG) esterification, AICAR did increase the ratio of FA partitioned to oxidation relative to TAG esterification (LFA: +65%, P<0.05). AICAR significantly blunted endogenous TAG hydrolysis (LFA: -294%, P<0.001; HFA: -117%, P<0.05), but had no effect on endogenous oxidation rates, suggesting a better matching between TAG hydrolysis and subsequent oxidative needs of the muscle. There was no effect of AICAR on the already elevated rates of glucose oxidation during contraction. These results suggest that FA metabolism is very sensitive to AMPK alpha2 stimulation during contraction.

  2. Determination of the main impurities formed after acid hydrolysis of soybean extracts and the in vitro mutagenicity and genotoxicity studies of 5-ethoxymethyl-2-furfural.

    PubMed

    Nemitz, Marina C; Picada, Jaqueline N; da Silva, Juliana; Garcia, Ana Letícia H; Papke, Débora K M; Grivicich, Ivana; Steppe, Martin; von Poser, Gilsane L; Teixeira, Helder F

    2016-09-10

    Soybean acid hydrolyzed extracts are raw-materials widely used for manufacturing of pharmaceuticals and cosmetics products due to their high content of isoflavone aglycones. In the present study, the main sugar degradation products 5-hydroxymethyl-2-furfural (HMF) and 5-ethoxymethyl-2-furfural (EMF) were quantitatively determined after acid hydrolysis of extracts from different soybean cultivars by a validated liquid chromatography method. The furanic compounds determined in samples cover the range of 0.16-0.21mg/mL and 0.22-0.33mg/mL for HMF and EMF, respectively. Complementarily, due to the scarce literature regarding the EMF toxicology, this study also assessed the EMF mutagenicity by the Salmonella/microsome test and genotoxicity by the comet assay. The results revealed that EMF did not show mutagenicity at the range of 50-5000μg/plate in S. typhimurium strains TA98, TA97a, TA100, TA102 and TA1535, but induced DNA damage in HepG2 cells at non-cytotoxic doses of 0.1-1.3mg/mL, mainly by oxidative stress mechanisms. Based on literature of HMF genotoxicity, and considering the EMF genotoxicity results herein shown, purification procedures to remove these impurities from extracts are recommended during healthcare products development to ensure the security of the products. PMID:27475406

  3. Acid Hydrolysis and Molecular Density of Phytoglycogen and Liver Glycogen Helps Understand the Bonding in Glycogen α (Composite) Particles

    PubMed Central

    Powell, Prudence O.; Sullivan, Mitchell A.; Sheehy, Joshua J.; Schulz, Benjamin L.; Warren, Frederick J.; Gilbert, Robert G.

    2015-01-01

    Phytoglycogen (from certain mutant plants) and animal glycogen are highly branched glucose polymers with similarities in structural features and molecular size range. Both appear to form composite α particles from smaller β particles. The molecular size distribution of liver glycogen is bimodal, with distinct α and β components, while that of phytoglycogen is monomodal. This study aims to enhance our understanding of the nature of the link between liver-glycogen β particles resulting in the formation of large α particles. It examines the time evolution of the size distribution of these molecules during acid hydrolysis, and the size dependence of the molecular density of both glucans. The monomodal distribution of phytoglycogen decreases uniformly in time with hydrolysis, while with glycogen, the large particles degrade significantly more quickly. The size dependence of the molecular density shows qualitatively different shapes for these two types of molecules. The data, combined with a quantitative model for the evolution of the distribution during degradation, suggest that the bonding between β into α particles is different between phytoglycogen and liver glycogen, with the formation of a glycosidic linkage for phytoglycogen and a covalent or strong non-covalent linkage, most probably involving a protein, for glycogen as most likely. This finding is of importance for diabetes, where α-particle structure is impaired. PMID:25799321

  4. Acid hydrolysis and molecular density of phytoglycogen and liver glycogen helps understand the bonding in glycogen α (composite) particles.

    PubMed

    Powell, Prudence O; Sullivan, Mitchell A; Sheehy, Joshua J; Schulz, Benjamin L; Warren, Frederick J; Gilbert, Robert G

    2015-01-01

    Phytoglycogen (from certain mutant plants) and animal glycogen are highly branched glucose polymers with similarities in structural features and molecular size range. Both appear to form composite α particles from smaller β particles. The molecular size distribution of liver glycogen is bimodal, with distinct α and β components, while that of phytoglycogen is monomodal. This study aims to enhance our understanding of the nature of the link between liver-glycogen β particles resulting in the formation of large α particles. It examines the time evolution of the size distribution of these molecules during acid hydrolysis, and the size dependence of the molecular density of both glucans. The monomodal distribution of phytoglycogen decreases uniformly in time with hydrolysis, while with glycogen, the large particles degrade significantly more quickly. The size dependence of the molecular density shows qualitatively different shapes for these two types of molecules. The data, combined with a quantitative model for the evolution of the distribution during degradation, suggest that the bonding between β into α particles is different between phytoglycogen and liver glycogen, with the formation of a glycosidic linkage for phytoglycogen and a covalent or strong non-covalent linkage, most probably involving a protein, for glycogen as most likely. This finding is of importance for diabetes, where α-particle structure is impaired.

  5. Progressing batch hydrolysis process

    DOEpatents

    Wright, J.D.

    1985-01-10

    A progressive batch hydrolysis process is disclosed for producing sugar from a lignocellulosic feedstock. It comprises passing a stream of dilute acid serially through a plurality of percolation hydrolysis reactors charged with feed stock, at a flow rate, temperature and pressure sufficient to substantially convert all the cellulose component of the feed stock to glucose. The cooled dilute acid stream containing glucose, after exiting the last percolation hydrolysis reactor, serially fed through a plurality of pre-hydrolysis percolation reactors, charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the hemicellulose component of said feedstock to glucose. The dilute acid stream containing glucose is cooled after it exits the last prehydrolysis reactor.

  6. The salt stress-induced LPA response in Chlamydomonas is produced via PLA₂ hydrolysis of DGK-generated phosphatidic acid.

    PubMed

    Arisz, Steven A; Munnik, Teun

    2011-11-01

    The unicellular green alga Chlamydomonas has frequently been used as a eukaryotic model system to study intracellular phospholipid signaling pathways in response to environmental stresses. Earlier, we found that hypersalinity induced a rapid increase in the putative lipid second messenger, phosphatidic acid (PA), which was suggested to be generated via activation of a phospholipase D (PLD) pathway and the combined action of a phospholipase C/diacylglycerol kinase (PLC/DGK) pathway. Lysophosphatidic acid (LPA) was also increased and was suggested to reflect a phospholipase A₂ (PLA₂) activity based on pharmacological evidence. The question of PA's and LPA's origin is, however, more complicated, especially as both function as precursors in the biosynthesis of phospho- and galactolipids. To address this complexity, a combination of fatty acid-molecular species analysis and in vivo ³²P-radiolabeling was performed. Evidence is provided that LPA is formed from a distinct pool of PA characterized by a high α-linolenic acid (18:3n-3) content. This molecular species was highly enriched in the polyphosphoinositide fraction, which is the substrate for PLC to form diacylglycerol. Together with differential ³²P-radiolabeling studies and earlier PLD-transphosphatidylation and PLA₂-inhibitor assays, the data were consistent with the hypothesis that the salt-induced LPA response is primarily generated through PLA₂-mediated hydrolysis of DGK-generated PA and that PLD or de novo synthesis [via endoplasmic reticulum - or plastid-localized routes] is not a major contributor.

  7. Response surface optimization of corn stover pretreatment using dilute phosphoric acid for enzymatic hydrolysis and ethanol production.

    PubMed

    Avci, Ayse; Saha, Badal C; Dien, Bruce S; Kennedy, Gregory J; Cotta, Michael A

    2013-02-01

    Dilute H(3)PO(4) (0.0-2.0%, v/v) was used to pretreat corn stover (10%, w/w) for conversion to ethanol. Pretreatment conditions were optimized for temperature, acid loading, and time using central composite design. Optimal pretreatment conditions were chosen to promote sugar yields following enzymatic digestion while minimizing formation of furans, which are potent inhibitors of fermentation. The maximum glucose yield (85%) was obtained after enzymatic hydrolysis of corn stover pretreated with 0.5% (v/v) acid at 180°C for 15min while highest yield for xylose (91.4%) was observed from corn stover pretreated with 1% (v/v) acid at 160°C for 10min. About 26.4±0.1g ethanol was produced per L by recombinant Escherichia coli strain FBR5 from 55.1±1.0g sugars generated from enzymatically hydrolyzed corn stover (10%, w/w) pretreated under a balanced optimized condition (161.81°C, 0.78% acid, 9.78min) where only 0.4±0.0g furfural and 0.1±0.0 hydroxylmethyl furfural were produced.

  8. Imidase catalyzing desymmetric imide hydrolysis forming optically active 3-substituted glutaric acid monoamides for the synthesis of gamma-aminobutyric acid (GABA) analogs.

    PubMed

    Nojiri, Masutoshi; Hibi, Makoto; Shizawa, Hiroaki; Horinouchi, Nobuyuki; Yasohara, Yoshihiko; Takahashi, Satomi; Ogawa, Jun

    2015-12-01

    The recent use of optically active 3-substituted gamma-aminobutyric acid (GABA) analogs in human therapeutics has identified a need for an efficient, stereoselective method of their synthesis. Here, bacterial strains were screened for enzymes capable of stereospecific hydrolysis of 3-substituted glutarimides to generate (R)-3-substituted glutaric acid monoamides. The bacteria Alcaligenes faecalis NBRC13111 and Burkholderia phytofirmans DSM17436 were discovered to hydrolyze 3-(4-chlorophenyl) glutarimide (CGI) to (R)-3-(4-chlorophenyl) glutaric acid monoamide (CGM) with 98.1% enantiomeric excess (e.e.) and 97.5% e.e., respectively. B. phytofirmans DSM17436 could also hydrolyze 3-isobutyl glutarimide (IBI) to produce (R)-3-isobutyl glutaric acid monoamide (IBM) with 94.9% e.e. BpIH, an imidase, was purified from B. phytofirmans DSM17436 and found to generate (R)-CGM from CGI with specific activity of 0.95 U/mg. The amino acid sequence of BpIH had a 75% sequence identity to that of allantoinase from A. faecalis NBRC13111 (AfIH). The purified recombinant BpIH and AfIH catalyzed (R)-selective hydrolysis of CGI and IBI. In addition, a preliminary investigation of the enzymatic properties of BpIH and AfIH revealed that both enzymes were stable in the range of pH 6-10, with an optimal pH of 9.0, stable at temperatures below 40 °C, and were not metalloproteins. These results indicate that the use of this class of hydrolase to generate optically active 3-substituted glutaric acid monoamide could simplify the production of specific chiral GABA analogs for drug therapeutics.

  9. Black liquor-derived carbonaceous solid acid catalyst for the hydrolysis of pretreated rice straw in ionic liquid.

    PubMed

    Bai, Chenxi; Zhu, Linfeng; Shen, Feng; Qi, Xinhua

    2016-11-01

    Lignin-containing black liquor from pretreatment of rice straw by KOH aqueous solution was applied to prepare a carbonaceous solid acid catalyst, in which KOH played dual roles of extracting lignin from rice straw and developing porosity of the carbon material as an activation agent. The synthesized black liquor-derived carbon material was applied in catalytic hydrolysis of the residue solid from the pretreatment of rice straw, which was mainly composed of cellulose and hemicellulose, and showed excellent activity for the production of total reducing sugars (TRS) in ionic liquid, 1-butyl-3-methyl imidazolium chloride. The highest TRS yield of 63.4% was achieved at 140°C for 120min, which was much higher than that obtained from crude rice straw under the same reaction conditions (36.6% TRS yield). Overall, this study provides a renewable strategy for the utilization of all components of lignocellulosic biomass. PMID:27599625

  10. High-performance liquid chromatographic determination of quercetin and isorhamnetin in rat tissues using beta-glucuronidase and acid hydrolysis.

    PubMed

    Morrice, P C; Wood, S G; Duthie, G G

    2000-02-11

    Quercetin is a plant polyphenol which is present in the diet as an aglycone and as sugar conjugates. Despite potent vasodilatory and antioxidant effects in vitro, destruction by intestinal organisms has been assumed to limit its nutritional relevance in the rat. However, we have refined extraction techniques using beta-glucuronidase followed by acid hydrolysis. Following this with HPLC methodology with post-column derivatisation, we have detected significant concentrations of quercetin and its metabolite, isorhamnetin, in tissues of rats maintained on quercetin-rich diets. Percentage recoveries are greater than 95% and intra-batch variation does not exceed 7% suggesting that the method may be useful in further studies of the biological role of this flavonoid. PMID:10718659

  11. Tranexamic Acid in Anesthetic Management of Surgical Procedures.

    PubMed

    Mayeux, Jessica; Alwon, Kathy; Collins, Shawn; Hewer, Ian

    2016-06-01

    Blood loss during surgical procedures poses a grave risk to the patient, but transfusion is costly and associated with adverse outcomes. Antifibrinolytics, however, offer an economical and effective means of decreasing blood loss associated with surgical procedures. Tranexamic acid (TXA) is an antifibrinolytic that blocks lysine-binding sites of fibrinogen and fibrin, preventing the breakdown of existing clots. This journal course reviews extensive research demonstrating that antifibrinolytics such as TXA decrease blood loss and in some studies reduce allogeneic transfusion requirements. In addition, this journal course addresses concerns that use of antifibrinolytics increases embolic events, reviews research that demonstrates TXA does not increase the incidence of vascular occlusive events, and describes methods of TXA use in cardiac and orthopedic surgical procedures, neurosurgery, and obstetrics. The Certified Registered Nurse Anesthetist should consider the possibility, on a case-by-case basis, of using TXA in surgical procedures to reduce blood loss with minimal adverse effects. PMID:27501656

  12. Effect of carboxylic acid adsorption on the hydrolysis and sintered properties of aluminum nitride powder

    SciTech Connect

    Egashira, Makoto; Shimizu, Yasuhiro; Takao, Yuji; Yamaguchi, Ryoji; Ishikawa, Yasuhiro . Dept. of Materials Science and Engineering)

    1994-07-01

    To suppress the reactivity of AlN powder with water, chemical surface modification with carboxylic acids has been investigated. It was found that the chemical stability of AlN powder increased as the number of carbon atoms in carboxylic acids used for the surface treatment increased. Among the carboxylic acids tested, stearic acid was the most promising from the viewpoint of the chemical stability of the treated powder and the thermal conductivity of the sintered ceramics prepared by cold isostatic pressing and pressureless sintering.

  13. Heterogeneous ceria catalyst with water-tolerant Lewis acidic sites for one-pot synthesis of 1,3-diols via Prins condensation and hydrolysis reactions.

    PubMed

    Wang, Yehong; Wang, Feng; Song, Qi; Xin, Qin; Xu, Shutao; Xu, Jie

    2013-01-30

    The use of a heterogeneous Lewis acid catalyst, which is insoluble and easily separable during the reaction, is a promising option for hydrolysis reactions from both environmental and practical viewpoints. In this study, ceria showed excellent catalytic activity in the hydrolysis of 4-methyl-1,3-dioxane to 1,3-butanediol in 95% yield and in the one-pot synthesis of 1,3-butanediol from propylene and formaldehyde via Prins condensation and hydrolysis reactions in an overall yield of 60%. In-depth investigations revealed that ceria is a water-tolerant Lewis acid catalyst, which has seldom been reported previously. The ceria catalysts showed rather unusual high activity in hydrolysis, with a turnover number (TON) of 260, which is rather high for bulk oxide catalysts, whose TONs are usually less than 100. Our conclusion that ceria functions as a Lewis acid catalyst in hydrolysis reactions is firmly supported by thorough characterizations with IR and Raman spectroscopy, acidity measurements with IR and (31)P magic-angle-spinning NMR spectroscopy, Na(+)/H(+) exchange tests, analyses using the in situ active-site capping method, and isotope-labeling studies. A relationship between surface vacancy sites and catalytic activity has been established. CeO(2)(111) has been confirmed to be the catalytically active crystalline facet for hydrolysis. Water has been found to be associatively adsorbed on oxygen vacancy sites with medium strength, which does not lead to water dissociation to form stable hydroxides. This explains why the ceria catalyst is water-tolerant. PMID:23228093

  14. Ultrasound-assisted enzymatic hydrolysis for iodinated amino acid extraction from edible seaweed before reversed-phase high performance liquid chromatography-inductively coupled plasma-mass spectrometry.

    PubMed

    Romarís-Hortas, Vanessa; Bermejo-Barrera, Pilar; Moreda-Piñeiro, Antonio

    2013-09-27

    The combination of reverse phase high performance liquid chromatography (RP-HPLC) with inductively coupled plasma mass spectrometry (ICP-MS) was used for the determination of monoiodotyrosine (MIT) and diiodotyrosine (DIT) in edible seaweed. A sample pre-treatment based on ultrasound assisted enzymatic hydrolysis was optimized for the extraction of these iodinated amino acids. Pancreatin was selected as the most adequate type of enzyme, and parameters affecting the extraction efficiency (pH, temperature, mass of enzyme and extraction time) were evaluated by univariate approaches. In addition, extractable inorganic iodine (iodide) was also quantified by anion exchange high performance liquid chromatography (AE-HPLC) coupled with ICP-MS. The proposed procedure offered limits of detection of 1.1 and 4.3ngg(-1) for MIT and DIT, respectively. Total iodine contents in seaweed, as well as total iodine in enzymatic digests were measured by ICP-MS after microwave assisted alkaline digestion with tetramethylamonium hydroxide (TMAH) for total iodine assessment, and also by treating the pancreatin extracts (extractable total iodine assessment). The optimized procedure was successfully applied to five different types of edible seaweed. The highest total iodine content, and also the highest iodide levels, was found in the brown seaweed Kombu (6646±45μgg(-1)). Regarding iodinated amino acids, Nori (a red seaweed) was by far the one with the highest amount of both species (42±3 and 0.41±0.024μgg(-1) for MIT and DIT, respectively). In general, MIT concentrations were much higher than the amounts of DIT, which suggests that iodine from iodinated proteins in seaweed is most likely bound in the form of MIT residues.

  15. VLDL hydrolysis by LPL activates PPAR-alpha through generation of unbound fatty acids.

    PubMed

    Ruby, Maxwell A; Goldenson, Benjamin; Orasanu, Gabriela; Johnston, Thomas P; Plutzky, Jorge; Krauss, Ronald M

    2010-08-01

    Recent evidence suggests that lipoproteins serve as circulating reservoirs of peroxisomal proliferator activated receptor (PPAR) ligands that are accessible through lipolysis. The present study was conducted to determine the biochemical basis of PPAR-alpha activation by lipolysis products and their contribution to PPAR-alpha function in vivo. PPAR-alpha activation was measured in bovine aortic endothelial cells following treatment with human plasma, VLDL lipolysis products, or oleic acid. While plasma failed to activate PPAR-alpha, oleic acid performed similarly to VLDL lipolysis products. Therefore, fatty acids are likely to be the PPAR-alpha ligands generated by VLDL lipolysis. Indeed, unbound fatty acid concentration determined PPAR-alpha activation regardless of fatty acid source, with PPAR-alpha activation occurring only at unbound fatty acid concentrations that are unachievable under physiological conditions without lipase action. In mice, a synthetic lipase inhibitor (poloxamer-407) attenuated fasting-induced changes in expression of PPAR-alpha target genes. Apolipoprotein CIII (apoCIII), an endogenous inhibitor of lipoprotein and hepatic lipase, regulated access to the lipoprotein pool of PPAR-alpha ligands, because addition of exogenous apoCIII inhibited, and removal of endogenous apoCIII potentiated, lipolytic PPAR-alpha activation. These data suggest that the PPAR-alpha response is generated by unbound fatty acids released locally by lipase activity and not by circulating plasma fatty acids.

  16. Titan's Primordial Soup: Formation of Amino Acids via Low-Temperature Hydrolysis of Tholins

    NASA Astrophysics Data System (ADS)

    Neish, Catherine D.; Somogyi, Árpád; Smith, Mark A.

    2010-04-01

    Titan organic haze analogues, or "tholins," produce biomolecules when hydrolyzed at low temperature over long timescales. By using a combination of high-resolution mass spectroscopy and tandem mass spectrometry fragmentation techniques, four amino acids were identified in a tholin sample that had been hydrolyzed in a 13 wt % ammonia-water solution at 253 ± 1 K and 293 ± 1 K for 1 year. These four species have been assigned as the amino acids asparagine, aspartic acid, glutamine, and glutamic acid. This represents the first detection of biologically relevant molecules created under conditions thought to be similar to those found in impact melt pools and cryolavas on Titan, which are at a stage of chemical evolution not unlike the "primordial soup" of the early Earth. Future missions to Titan should therefore carry instrumentation capable of, but certainly not limited to, detecting amino acids and other prebiotic molecules on Titan's surface.

  17. Chemical synthesis and enzymatic, stereoselective hydrolysis of a functionalized dihydropyrimidine for the synthesis of β-amino acids.

    PubMed

    Slomka, Christin; Zhong, Sabilla; Fellinger, Anna; Engel, Ulrike; Syldatk, Christoph; Bräse, Stefan; Rudat, Jens

    2015-12-01

    A novel substrate, 6-(4-nitrophenyl)dihydropyrimidine-2,4(1H,3H)-dione (pNO2PheDU), was chemically synthesized and analytically verified for the potential biocatalytic synthesis of enantiopure β-amino acids. The hydantoinase (EC 3.5.2.2) from Arthrobacter crystallopoietes DSM20117 was chosen to prove the enzymatic hydrolysis of this substrate, since previous investigations showed activities of this enzyme toward 6-monosubstituted dihydrouracils. Whole cell biotransformations with recombinant Escherichia coli expressing the hydantoinase showed degradation of pNO2PheDU. Additionally, the corresponding N-carbamoyl-β-amino acid (NCarbpNO2 βPhe) was chemically synthesized, an HPLC-method with chiral stationary phases for detection of this product was established and thus (S)-enantioselectivity toward pNO2PheDU has been shown. Consequently this novel substrate is a potential precursor for the enantiopure β-amino acid para-nitro-β-phenylalanine (pNO2 βPhe). PMID:26705241

  18. Improving enzymatic hydrolysis of corn stover pretreated by ethylene glycol-perchloric acid-water mixture.

    PubMed

    He, Yu-Cai; Liu, Feng; Gong, Lei; Lu, Ting; Ding, Yun; Zhang, Dan-Ping; Qing, Qing; Zhang, Yue

    2015-02-01

    To improve the enzymatic saccharification of lignocellulosic biomass, a mixture of ethylene glycol-HClO4-water (88.8:1.2:10, w/w/w) was used for pretreating corn stover in this study. After the optimization in oil-bath system, the optimum pretreatment temperature and time were 130 °C and 30 min, respectively. After the saccharification of 10 g/L pretreated corn stover for 48 h, the saccharification rate was obtained in the yield of 77.4 %. To decrease pretreatment temperature and shorten pretreatment time, ethylene glycol-HClO4-water (88.8:1.2:10, w/w/w) media under microwave irradiation was employed to pretreat corn stover effectively at 100 °C and 200 W for 5 min. Finally, the recovered hydrolyzates containing glucose obtained from the enzymatic hydrolysis of pretreated corn stovers could be fermented into ethanol efficiently. These results would be helpful for developing a cost-effective pretreatment combined with enzymatic saccharification of cellulosic materials for the production of lignocellulosic ethanol.

  19. Waste activated sludge hydrolysis and short-chain fatty acids accumulation under mesophilic and thermophilic conditions: effect of pH.

    PubMed

    Zhang, Peng; Chen, Yinguang; Zhou, Qi

    2009-08-01

    The effect of pH (4.0-11.0) on waste activated sludge (WAS) hydrolysis and short-chain fatty acids (SCFAs) accumulation under mesophilic and thermophilic conditions were investigated. The WAS hydrolysis increased markedly in thermophilic fermentation compared to mesophilic fermentation at any pH investigated. The hydrolysis at alkaline pHs (8.0-11.0) was greater than that at acidic pHs, but both of the acidic and alkaline hydrolysis was higher than that pH uncontrolled under either mesophilic or thermophilic conditions. No matter in mesophilic or thermophilic fermentation, the accumulation of SCFAs at alkaline pHs was greater than at acidic or uncontrolled pHs. The optimum SCFAs accumulation was 0.298g COD/g volatile suspended solids (VSS) with mesophilic fermentation, and 0.368 with thermophilic fermentation, which was observed respectively at pH 9.0 and fermentation time 5 d and pH 8.0 and time 9 d. The maximum SCFAs productions reported in this study were much greater than that in the literature. The analysis of the SCFAs composition showed that acetic acid was the prevalent acid in the accumulated SCFAs at any pH investigated under both temperatures, followed by propionic acid and n-valeric acid. Nevertheless, during the entire mesophilic and thermophilic fermentation the activity of methanogens was inhibited severely at acid or alkaline pHs, and the highest methane concentration was obtained at pH 7.0 in most cases. The studies of carbon mass balance showed that during WAS fermentation the reduction of VSS decreased with the increase of pH, and the thermophilic VSS reduction was greater than the mesophilic one. Further investigation indicated that most of the reduced VSS was converted to soluble protein and carbohydrate and SCFAs in two fermentations systems, while little formed methane and carbon dioxide.

  20. Dilute oxalic acid pretreatment for high total sugar recovery in pretreatment and subsequent enzymatic hydrolysis.

    PubMed

    Qing, Qing; Huang, Meizi; He, Yucai; Wang, Liqun; Zhang, Yue

    2015-12-01

    Oxalic acid was evaluated as an alternative reagent to mineral inorganic acid in pretreatment of corncob to achieve high xylose yield in addition to highly digestible solid residue. A quadratic polynomial model of xylose formation was developed for optimization of pretreatment process by the response surface methodology based on the impact factors of pretreatment temperature, reaction time, acid concentration, and solid-to-liquid ratio. The highest xylose yield was 94.3 % that was obtained under the pretreatment condition of 140 °C for 40 min with 0.5 wt% oxalic acid at a solid loading of 7.5 %. Under these conditions, the xylose yield results of verification experiments were very close to the model prediction, which indicated that the model was applicable. The solid residue generated under this condition also demonstrated a satisfactory enzymatic digestibility and fermentability. PMID:26494137

  1. Fuel ethanol production from corn stover under optimized dilute phosphoric acid pretreatment and enzymatic hydrolysis

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Ethanol is a renewable oxygenated fuel. Dilute acid pretreatment is a promising pretreatment technology for conversion of lignocellulosic biomass to fuel ethanol. Generation of fermentable sugars from corn stover involves pretreatment and enzymatic saccharification. Pretreatment is crucial as nat...

  2. Progressing batch hydrolysis process

    DOEpatents

    Wright, John D.

    1986-01-01

    A progressive batch hydrolysis process for producing sugar from a lignocellulosic feedstock, comprising passing a stream of dilute acid serially through a plurality of percolation hydrolysis reactors charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the cellulose component of the feedstock to glucose; cooling said dilute acid stream containing glucose, after exiting the last percolation hydrolysis reactor, then feeding said dilute acid stream serially through a plurality of prehydrolysis percolation reactors, charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the hemicellulose component of said feedstock to glucose; and cooling the dilute acid stream containing glucose after it exits the last prehydrolysis reactor.

  3. Enzymatic hydrolysis and fermentation of pretreated cashew apple bagasse with alkali and diluted sulfuric Acid for bioethanol production.

    PubMed

    Rocha, Maria Valderez Ponte; Rodrigues, Tigressa Helena Soares; de Macedo, Gorete Ribeiro; Gonçalves, Luciana R B

    2009-05-01

    The aim of this work was to optimize the enzymatic hydrolysis of the cellulose fraction of cashew apple bagasse (CAB) after diluted acid (CAB-H) and alkali pretreatment (CAB-OH), and to evaluate its fermentation to ethanol using Saccharomyces cerevisiae. Glucose conversion of 82 +/- 2 mg/g CAB-H and 730 +/- 20 mg/g CAB-OH was obtained when 2% (w/v) of solid and 30 FPU/g bagasse was used during hydrolysis at 45 degrees C, 2-fold higher than when using 15 FPU/g bagasse, 44 +/- 2 mg/g CAB-H, and 450 +/- 50 mg/g CAB-OH, respectively. Ethanol concentration and productivity, achieved after 6 h of fermentation, were 20.0 +/- 0.2 g L(-1) and 3.33 g L(-1) h(-1), respectively, when using CAB-OH hydrolyzate (initial glucose concentration of 52.4 g L(-1)). For CAB-H hydrolyzate (initial glucose concentration of 17.4 g L(-1)), ethanol concentration and productivity were 8.2 +/- 0.1 g L(-1) and 2.7 g L(-1) h(-1) in 3 h, respectively. Hydrolyzates fermentation resulted in an ethanol yield of 0.38 and 0.47 g/g glucose with pretreated CAB-OH and CAB-H, respectively. Ethanol concentration and productivity, obtained using CAB-OH hydrolyzate, were close to the values obtained in the conventional ethanol fermentation of cashew apple juice or sugar cane juice.

  4. Hydrolysis of Np(IV) and Pu(IV) and Their Complexation by Aqueous Orthosilicic Acid Si(OH)4

    SciTech Connect

    Yusov, A B.; Fedoseev, A M.; Delegard, Calvin H.

    2004-12-10

    The hydrolysis and interaction of Np(IV) and Pu(IV) with orthosilicic acid, Si(OH)4, were studied in 0.1-1.0 M ionic strength aqueous solutions. Spectrophotometry was used to study these reactions at about 10-4 M Np(IV) and Pu(IV) concentrations. The first hydrolysis constants, Khydr, agree with the majority of earlier spectrophotometric and potentiometric data. The absorption spectra of NpOH3+ and PuOH3+ were obtained by spectral deconvolution. Reasons to explain the overestimation of Khydr obtained by other methods [by extraction of trace amounts of Np(IV) and Pu(IV) and by solubility] are discussed. Formation of the complexes NpOSi(OH)33+ and PuOSi(OH)33+ is demonstrated in the p[H+] range 1.4-2.1 and 0.7-1.4, respectively. Measured values of equilibrium constants of the reaction M4+ + Si(OH)4 ? MOSi(OH)33+ + H+ at ionic strength I=1.0 are log ?1 = 0.41?0.02 and 1.04?0.04, respectively, for Np(IV) and Pu(IV). The stability constants of the NpOSi(OH)33+ and PuOSi(OH)33+ complexes, recalculated to zero ionic strength, are log ?10 = 11.2 and 11.8, respectively. The correlation between Khydr and ?1, as observed for all earlier studied metal ions, also occurs for both Np(IV) and Pu(IV).

  5. Dependence of RIG-I Nucleic Acid-Binding and ATP Hydrolysis on Activation of Type I Interferon Response.

    PubMed

    Baek, Yu Mi; Yoon, Soojin; Hwang, Yeo Eun; Kim, Dong-Eun

    2016-08-01

    Exogenous nucleic acids induce an innate immune response in mammalian host cells through activation of the retinoic acid-inducible gene I (RIG-I). We evaluated RIG-I protein for RNA binding and ATPase stimulation with RNA ligands to investigate the correlation with the extent of immune response through RIG-I activation in cells. RIG-I protein favored blunt-ended, double-stranded RNA (dsRNA) ligands over sticky-ended dsRNA. Moreover, the presence of the 5'-triphosphate (5'-ppp) moiety in dsRNA further enhanced binding affinity to RIG-I. Two structural motifs in RNA, blunt ends in dsRNA and 5'-ppp, stimulated the ATP hydrolysis activity of RIG-I. These structural motifs also strongly induced IFN expression as an innate immune response in cells. Therefore, we suggest that IFN induction through RIG-I activation is mainly determined by structural motifs in dsRNA that increase its affinity for RIG-I protein and stimulate ATPase activity in RIG-I. PMID:27574504

  6. Dependence of RIG-I Nucleic Acid-Binding and ATP Hydrolysis on Activation of Type I Interferon Response

    PubMed Central

    Baek, Yu Mi; Yoon, Soojin; Hwang, Yeo Eun

    2016-01-01

    Exogenous nucleic acids induce an innate immune response in mammalian host cells through activation of the retinoic acid-inducible gene I (RIG-I). We evaluated RIG-I protein for RNA binding and ATPase stimulation with RNA ligands to investigate the correlation with the extent of immune response through RIG-I activation in cells. RIG-I protein favored blunt-ended, double-stranded RNA (dsRNA) ligands over sticky-ended dsRNA. Moreover, the presence of the 5'-triphosphate (5'-ppp) moiety in dsRNA further enhanced binding affinity to RIG-I. Two structural motifs in RNA, blunt ends in dsRNA and 5'-ppp, stimulated the ATP hydrolysis activity of RIG-I. These structural motifs also strongly induced IFN expression as an innate immune response in cells. Therefore, we suggest that IFN induction through RIG-I activation is mainly determined by structural motifs in dsRNA that increase its affinity for RIG-I protein and stimulate ATPase activity in RIG-I. PMID:27574504

  7. Titan's Primordial Soup: Formation of Amino Acids via Low Temperature Hydrolysis of Tholins

    NASA Astrophysics Data System (ADS)

    Neish, Catherine; Somogyi, Á.; Smith, M. A.

    2009-09-01

    Titan, Saturn's largest moon, is a world rich in the "stuff of life". Reactions occurring in its dense nitrogen-methane atmosphere produce a wide variety of organic molecules, which subsequently rain down onto its surface. Water - thought to be another important ingredient for life - is likewise abundant on Titan. Theoretical models of Titan's formation predict that its interior consists of an ice I layer several tens of kilometers thick overlying a liquid ammonia-rich water layer several hundred kilometers thick (Tobie et al., 2005). Though its surface temperature of 94K dictates that Titan is on average too cold for liquid water to persist at its surface, melting caused by impacts and/or cryovolcanism may lead to its episodic availability. Impact melt pools on Titan would likely remain liquid for 102 - 104 years before freezing (O'Brien et al., 2005). The combination of complex organic molecules and transient locales of liquid water make Titan an interesting natural laboratory for studying prebiotic chemistry. In this work, we sought to determine what biomolecules might be formed under conditions analogous to those found in transient liquid water environments on Titan. We hydrolyzed Titan organic haze analogues, or "tholins", in 13 wt. % ammonia-water at 253K and 293K for a year. Using a combination of high resolution mass spectroscopy and tandem mass spectroscopy fragmentation techniques, four amino acids were identified in the hydrolyzed tholin sample. These four species have been assigned as the amino acids asparagine, aspartic acid, glutamine, and glutamic acid. This represents the first detection of biologically relevant molecules created under conditions similar to those found in impact melt pools and cryolavas on Titan. Future missions to Titan should therefore carry instrumentation capable of detecting amino acids and other prebiotically relevant molecules on its surface This work was supported by the NASA Exobiology Program.

  8. Penicillin Hydrolysis: A Kinetic Study of a Multistep, Multiproduct Reaction.

    ERIC Educational Resources Information Center

    McCarrick, Thomas A.; McLafferty, Fred W.

    1984-01-01

    Background, procedures used, and typical results are provided for an experiment in which students carry out the necessary measurements on the acid-catalysis of penicillin in two hours. By applying kinetic theory to the data obtained, the reaction pathways for the hydrolysis of potassium benzyl penicillin are elucidated. (JN)

  9. Structures of polynuclear complexes of palladium(II) and platinum(II) formed by slow hydrolysis in acidic aqueous solution.

    PubMed

    Torapava, Natallia; Elding, Lars I; Mändar, Hugo; Roosalu, Kaspar; Persson, Ingmar

    2013-06-01

    The aqua ions of palladium(II) and platinum(II) undergo extremely slow hydrolysis in strongly acidic aqueous solution, resulting in polynuclear complexes. The size and structures of these species have been determined by EXAFS and small angle X-ray scattering, SAXS. For palladium(II), the EXAFS data show that the Pd-O and Pd···Pd distances are identical to those of crystalline palladium(II) oxide, but the intensities of the Pd···Pd distances in the Fourier transform at 3.04 and 3.42 Å are significantly lower compared to those of crystalline PdO. Furthermore, no Pd···Pd distances beyond 4 Å are observed. These observations strongly indicate that the polynuclear palladium(II) complexes are oxido- and hydroxido-bridged species with the same core structure as solid palladium(II) oxide. Based on the number of Pd···Pd distances, as derived from the EXAFS data, their size can be estimated to be approximately two unit cells, or ca. 1.0 nm(3). For platinum(II), EXAFS data of the polynuclear species formed in the slow hydrolysis process show Pt-O and Pt···Pt distances identical to those of amorphous platinum(II) oxide, precipitating from the solution studied. The Pt···Pt distances are somewhat different from those reported for crystalline platinum(II) oxide. The polynuclear platinum(II) complexes have a similar structure to the palladium ones, but they are somewhat larger, with an estimated diameter of 1.5-3.0 nm. It has not been possible to precipitate any of these species by ultracentrifugation. They are detectable by SAXS, indicating diameters between 0.7 and 2 nm, in excellent agreement with the EXAFS observations. The number of oxido- relative to hydroxido bridges will increase with increasing size of the complex. The charge of the complexes will remain about the same, +4, at growth, with approximate formulas [Pd10O4(OH)8(H2O)12](4+) and [Pt14O8(OH)8(H2O)12](4+) for complexes with a size of 2 and 3 unit cells of the corresponding solid metal oxide

  10. Antioxidant activities of fucoidan degraded by gamma irradiation and acidic hydrolysis

    NASA Astrophysics Data System (ADS)

    Lim, Sangyong; Choi, Jong-il; Park, Hyun

    2015-04-01

    Low molecular weight fucoidan, prepared by radical degradation using gamma ray was investigated for its antioxidant activities with different assay methods. As the molecular weight of fucoidan decreased with a higher absorbed dose, ferric-reducing antioxidant power values increased, but β-carotene bleaching inhibition did not change significantly. The antioxidant activity of acid-degraded fucoidan was also examined to investigate the effect of different degradation methods. At the same molecular weight, fucoidan degraded by gamma irradiation showed higher 1,1-diphenyl-2-picrylhydrazyl radical scavenging activity than that observed with the acidic method. This result reveals that in addition to molecular weight, the degradation method affects the antioxidant activity of fucoidan.

  11. Physicochemical pretreatments and hydrolysis of furfural residues via carbon-based sulfonated solid acid.

    PubMed

    Ma, Bao Jun; Sun, Yuan; Lin, Ke Ying; Li, Bing; Liu, Wan Yi

    2014-03-01

    Potential commercial physicochemical pretreatment methods, NaOH/microwave and NaOH/ultrasound were developed, and the carbon-based sulfonated solid acid catalysts were prepared for furfural residues conversion into reducing sugars. After the two optimum pretreatments, both the content of cellulose increased (74.03%, 72.28%, respectively) and the content of hemicellulose (94.11%, 94.17% of removal rate, respectively) and lignin (91.75%, 92.09% of removal rate, respectively) decreased in furfural residues. The reducing sugar yields of furfural residues with the two physicochemical pretreatments on coal tar-based solid acid reached 33.94% and 33.13%, respectively, higher than that pretreated via NaOH alone (27%) and comparable to that pretreated via NaOH/H2O2 (35.67%). The XRD patterns, IR spectra and SEM images show microwave and ultrasound improve the pretreatment effect. The results demonstrate the carbon-based sulfonated solid acids and the physicochemical pretreatments are green, effective, low-cost for furfural residues conversion.

  12. Comparison of microbial inhibition and enzymatic hydrolysis rates of liquid and solid fractions produced from pretreatment of biomass with carbonic acid and liquid hot water.

    PubMed

    Yourchisin, Damon M; Van Walsum, G Peter

    2004-01-01

    This research quantified the enzymatic digestibility of the solid component and the microbial inhibition of the liquid component of pretreated aspen wood and corn stover hydrolysates. Products of liquid hot water and carbonic acid pretreatment were compared. Pretreatment temperatures tested ranged from 180 to 220 degrees C, and reaction times were varied between 4 and 64 min. Both microbial inhibition rates and enzymatic hydrolysis rates showed no difference between pretreatments containing carbonic acid and those not containing no carbonic acid. Microbial inhibition increased as the reaction severity increased, but only above a midpoint severity parameter of 200 degrees C for 16 min. Both the rates and yields of enzymatic hydrolysis displayed an increase from the lowest tested reaction severity to the highest tested reaction severity.

  13. The salt stress-induced LPA response in Chlamydomonas is produced via PLA2 hydrolysis of DGK-generated phosphatidic acid[S

    PubMed Central

    Arisz, Steven A.; Munnik, Teun

    2011-01-01

    The unicellular green alga Chlamydomonas has frequently been used as a eukaryotic model system to study intracellular phospholipid signaling pathways in response to environmental stresses. Earlier, we found that hypersalinity induced a rapid increase in the putative lipid second messenger, phosphatidic acid (PA), which was suggested to be generated via activation of a phospholipase D (PLD) pathway and the combined action of a phospholipase C/diacylglycerol kinase (PLC/DGK) pathway. Lysophosphatidic acid (LPA) was also increased and was suggested to reflect a phospholipase A2 (PLA2) activity based on pharmacological evidence. The question of PA's and LPA's origin is, however, more complicated, especially as both function as precursors in the biosynthesis of phospho- and galactolipids. To address this complexity, a combination of fatty acid-molecular species analysis and in vivo 32P-radiolabeling was performed. Evidence is provided that LPA is formed from a distinct pool of PA characterized by a high α-linolenic acid (18:3n-3) content. This molecular species was highly enriched in the polyphosphoinositide fraction, which is the substrate for PLC to form diacylglycerol. Together with differential 32P-radiolabeling studies and earlier PLD-transphosphatidylation and PLA2-inhibitor assays, the data were consistent with the hypothesis that the salt-induced LPA response is primarily generated through PLA2-mediated hydrolysis of DGK-generated PA and that PLD or de novo synthesis [via endoplasmic reticulum - or plastid-localized routes] is not a major contributor. PMID:21900174

  14. Incomplete recovery of prescription opioids in urine using enzymatic hydrolysis of glucuronide metabolites.

    PubMed

    Wang, Ping; Stone, Judith A; Chen, Katherine H; Gross, Susan F; Haller, Christine A; Wu, Alan H B

    2006-10-01

    Confirmation of opioids in urine samples of clinical patients requires liberation of opioids from their glucuronide conjugates. Both acid hydrolysis and enzyme hydrolysis using beta-glucuronidase from various sources have been reported, with the latter approach prevailing in most clinical toxicology laboratories. The goal of this study was to compare the efficiency of acid versus different enzyme hydrolysis methods in recovering morphine and common semisynthetic opioids from glucuronide standards and 78 patient urine samples that were screened positive for opioids as a class. Specimens were analyzed with a validated gas chromatography-mass spectrometry (GC-MS) procedure. With the exception of oxycodone, the results indicated that the majority of opioids tested were extensively glucuronide-conjugated in urine. Significantly, acid hydrolysis liberated > 90% of morphine and hydromorphone from their glucuronide standards but enzyme hydrolysis had lower and variable efficiency, depending on the opiate type and the enzyme source. In patient specimens, much higher concentrations of free codeine, morphine, hydromorphone, and oxymorphone were obtained with acid hydrolysis than with various enzyme methods. Incomplete hydrolysis using beta-glucuronidase could lead to false-negative results for many opioids when urine is tested for drugs of abuse. We conclude that acid hydrolysis is the method of choice for GC-MS confirmation of urine opioids.

  15. Pretreatment of Dried Distiller Grains with Solubles by Soaking in Aqueous Ammonia and Subsequent Enzymatic/Dilute Acid Hydrolysis to Produce Fermentable Sugars.

    PubMed

    Nghiem, Nhuan P; Montanti, Justin; Kim, Tae Hyun

    2016-05-01

    Dried distillers grains with solubles (DDGS), a co-product of corn ethanol production in the dry-grind process, was pretreated by soaking in aqueous ammonia (SAA) using a 15 % w/w NH4OH solution at a solid/liquid ratio of 1:10. The effect of pretreatment on subsequent enzymatic hydrolysis was studied at two temperatures (40 and 60 °C) and four reaction times (6, 12, 24, and 48 h). Highest glucose yield of 91 % theoretical was obtained for the DDGS pretreated at 60 °C and 24 h. The solubilized hemicellulose in the liquid fraction was further hydrolyzed with dilute H2SO4 to generate fermentable monomeric sugars. The conditions of acid hydrolysis included 1 and 4 wt% acid, 60 and 120 °C, and 0.5 and 1 h. Highest yields of xylose and arabinose were obtained at 4 wt% acid, 120 °C, and 1 h. The fermentability of the hydrolysate obtained by enzymatic hydrolysis of the SAA-pretreated DDGS was demonstrated in ethanol fermentation by Saccharomyces cerevisiae. The fermentability of the hydrolysate obtained by consecutive enzymatic and dilute acid hydrolysis was demonstrated using a succinic acid-producing microorganism, strain Escherichia coli AFP184. Under the fermentation conditions, complete utilization of glucose and arabinose was observed, whereas only 47 % of xylose was used. The succinic acid yield was 0.60 g/g total sugar consumed. PMID:26797927

  16. Purification and characterization of a chlorogenic acid hydrolase from Aspergillus niger catalysing the hydrolysis of chlorogenic acid.

    PubMed

    Asther, Michèle; Estrada Alvarado, Maria Isabel; Haon, Mireille; Navarro, David; Asther, Marcel; Lesage-Meessen, Laurence; Record, Eric

    2005-01-12

    Among 15 Aspergillus strains, Aspergillus niger BRFM 131 was selected for its high chlorogenic acid hydrolase activity. The enzyme was purified and characterized with respect to its physico-chemical and kinetic properties. Four chromatographic steps were necessary to purify the protein to homogeneity with a recovery of 2%. Km of the chlorogenic acid hydrolase was estimated to be 10 microM against chlorogenic acid as substrate. Under native conditions, the protein presented a molecular mass of 170 kDa, and SDS-PAGE analysis suggested the presence of two identical 80 kDa subunits. Isoelectric point was 6.0; pH optimum for activity was determined to be 6.0 and temperature optima to be 55 degrees C. The N-terminal sequence did not present any homology with other cinnamoyl ester hydrolases previously described suggesting the purification of a new protein. The chlorogenic acid hydrolase was used successfully for the production of caffeic acid, which possesses strong antioxidant properties, from natural substrates specially rich in chlorogenic acid like apple marc and coffee pulp.

  17. Enzymatic hydrolysis of cellulose pretreated with zinc chloride and hydrochloric acid

    SciTech Connect

    Chen, L.F.; Gong, C.S.

    1982-01-01

    Microcrystalline cellulose, Avicel, was dissolved in a concentrated solution of ZnCl/sub 2/ and 0.5% hydrochloric acid followed by heating at 145/sup 0/C for 6 min. after cooling, cellulose in its amorphous form was precipitated by the addition of acetone. The resulting cellulose was hydrolyzed by cellulase derived from Trichoderma viride. At concentrations of 20% cellulose and 1% cellulase, cellulose was hydrolyzed completely for form a solution of 19% glucose and 1% cellobiose within 72 h of incubation. 1 figure, 5 tables.

  18. Difference analysis of the enzymatic hydrolysis performance of acid-catalyzed steam-exploded corn stover before and after washing with water.

    PubMed

    Zhu, Junjun; Shi, Linli; Zhang, Lingling; Xu, Yong; Yong, Qiang; Ouyang, Jia; Yu, Shiyuan

    2016-10-01

    The difference in the enzymatic hydrolysis yield of acid-catalyzed steam-exploded corn stover (ASC) before and after washing with water reached approximately 15 % under the same conditions. The reasons for the difference in the yield between ASC and washed ASC (wASC) were determined through the analysis of the composition of ASC prehydrolyzate and sugar concentration of enzymatic hydrolyzate. Salts produced by neutralization (CaSO4, Na2SO4, K2SO4, and (NH4)2SO4), sugars (polysaccharides, oligosaccharides, and monosaccharides), sugar-degradation products (weak acids and furans), and lignin-degradation products (ethyl acetate extracts and nine main lignin-degradation products) were back-added to wASC. Results showed that these products, except furans, exerted negative effect on enzymatic hydrolysis. According to the characteristics of acid-catalyzed steam explosion pretreatment, the five sugar-degradation products' mixture and salts [Na2SO4, (NH4)2SO4] showed minimal negative inhibition effect on enzymatic hydrolysis. By contrast, furans demonstrated a promotion effect. Moreover, soluble sugars, such as 13 g/L xylose (decreased by 6.38 %), 5 g/L cellobiose (5.36 %), 10 g/L glucose (3.67 %), as well as lignin-degradation products, and ethyl acetate extracts (4.87 %), exhibited evident inhibition effect on enzymatic hydrolysis. Therefore, removal of soluble sugars and lignin-degradation products could effectively promote the enzymatic hydrolysis performance. PMID:27277746

  19. Difference analysis of the enzymatic hydrolysis performance of acid-catalyzed steam-exploded corn stover before and after washing with water.

    PubMed

    Zhu, Junjun; Shi, Linli; Zhang, Lingling; Xu, Yong; Yong, Qiang; Ouyang, Jia; Yu, Shiyuan

    2016-10-01

    The difference in the enzymatic hydrolysis yield of acid-catalyzed steam-exploded corn stover (ASC) before and after washing with water reached approximately 15 % under the same conditions. The reasons for the difference in the yield between ASC and washed ASC (wASC) were determined through the analysis of the composition of ASC prehydrolyzate and sugar concentration of enzymatic hydrolyzate. Salts produced by neutralization (CaSO4, Na2SO4, K2SO4, and (NH4)2SO4), sugars (polysaccharides, oligosaccharides, and monosaccharides), sugar-degradation products (weak acids and furans), and lignin-degradation products (ethyl acetate extracts and nine main lignin-degradation products) were back-added to wASC. Results showed that these products, except furans, exerted negative effect on enzymatic hydrolysis. According to the characteristics of acid-catalyzed steam explosion pretreatment, the five sugar-degradation products' mixture and salts [Na2SO4, (NH4)2SO4] showed minimal negative inhibition effect on enzymatic hydrolysis. By contrast, furans demonstrated a promotion effect. Moreover, soluble sugars, such as 13 g/L xylose (decreased by 6.38 %), 5 g/L cellobiose (5.36 %), 10 g/L glucose (3.67 %), as well as lignin-degradation products, and ethyl acetate extracts (4.87 %), exhibited evident inhibition effect on enzymatic hydrolysis. Therefore, removal of soluble sugars and lignin-degradation products could effectively promote the enzymatic hydrolysis performance.

  20. Evolutionary importance of the intramolecular pathways of hydrolysis of phosphate ester mixed anhydrides with amino acids and peptides.

    PubMed

    Liu, Ziwei; Beaufils, Damien; Rossi, Jean-Christophe; Pascal, Robert

    2014-12-11

    Aminoacyl adenylates (aa-AMPs) constitute essential intermediates of protein biosynthesis. Their polymerization in aqueous solution has often been claimed as a potential route to abiotic peptides in spite of a highly efficient CO2-promoted pathway of hydrolysis. Here we investigate the efficiency and relevance of this frequently overlooked pathway from model amino acid phosphate mixed anhydrides including aa-AMPs. Its predominance was demonstrated at CO2 concentrations matching that of physiological fluids or that of the present-day ocean, making a direct polymerization pathway unlikely. By contrast, the occurrence of the CO2-promoted pathway was observed to increase the efficiency of peptide bond formation owing to the high reactivity of the N-carboxyanhydride (NCA) intermediate. Even considering CO2 concentrations in early Earth liquid environments equivalent to present levels, mixed anhydrides would have polymerized predominantly through NCAs. The issue of a potential involvement of NCAs as biochemical metabolites could even be raised. The formation of peptide-phosphate mixed anhydrides from 5(4H)-oxazolones (transiently formed through prebiotically relevant peptide activation pathways) was also observed as well as the occurrence of the reverse cyclization process in the reactions of these mixed anhydrides. These processes constitute the core of a reaction network that could potentially have evolved towards the emergence of translation.

  1. Evolutionary Importance of the Intramolecular Pathways of Hydrolysis of Phosphate Ester Mixed Anhydrides with Amino Acids and Peptides

    PubMed Central

    Liu, Ziwei; Beaufils, Damien; Rossi, Jean-Christophe; Pascal, Robert

    2014-01-01

    Aminoacyl adenylates (aa-AMPs) constitute essential intermediates of protein biosynthesis. Their polymerization in aqueous solution has often been claimed as a potential route to abiotic peptides in spite of a highly efficient CO2-promoted pathway of hydrolysis. Here we investigate the efficiency and relevance of this frequently overlooked pathway from model amino acid phosphate mixed anhydrides including aa-AMPs. Its predominance was demonstrated at CO2 concentrations matching that of physiological fluids or that of the present-day ocean, making a direct polymerization pathway unlikely. By contrast, the occurrence of the CO2-promoted pathway was observed to increase the efficiency of peptide bond formation owing to the high reactivity of the N-carboxyanhydride (NCA) intermediate. Even considering CO2 concentrations in early Earth liquid environments equivalent to present levels, mixed anhydrides would have polymerized predominantly through NCAs. The issue of a potential involvement of NCAs as biochemical metabolites could even be raised. The formation of peptide–phosphate mixed anhydrides from 5(4H)-oxazolones (transiently formed through prebiotically relevant peptide activation pathways) was also observed as well as the occurrence of the reverse cyclization process in the reactions of these mixed anhydrides. These processes constitute the core of a reaction network that could potentially have evolved towards the emergence of translation. PMID:25501391

  2. High yield production of sugars from deproteinated palm kernel cake under microwave irradiation via dilute sulfuric acid hydrolysis.

    PubMed

    Fan, Suet-Pin; Jiang, Li-Qun; Chia, Chin-Hua; Fang, Zhen; Zakaria, Sarani; Chee, Kah-Leong

    2014-02-01

    Recent years, great interest has been devoted to the conversion of biomass-derived carbohydrate into sugars, such as glucose, mannose and fructose. These are important versatile intermediate products that are easily processed into high value-added biofuels. In this work, microwave-assisted dilute sulfuric acid hydrolysis of deproteinated palm kernel cake (DPKC) was systematically studied using Response Surface Methodology. The highest mannose yield (92.11%) was achieved at the optimized condition of 148°C, 0.75N H2SO4, 10min 31s and substrate to solvent (SS) ratio (w/v) of 1:49.69. Besides that, total fermentable sugars yield (77.11%), was obtained at 170°C, 0.181N H2SO4, 6min 6s and SS ratio (w/v) of 1:40. Ridge analysis was employed to further verify the optimum conditions. Thus, this work provides fundamental data of the practical use of DPKC as low cost, high yield and environmental-friendly material for the production of mannose and other sugars.

  3. Evolutionary Importance of the Intramolecular Pathways of Hydrolysis of Phosphate Ester Mixed Anhydrides with Amino Acids and Peptides

    NASA Astrophysics Data System (ADS)

    Liu, Ziwei; Beaufils, Damien; Rossi, Jean-Christophe; Pascal, Robert

    2014-12-01

    Aminoacyl adenylates (aa-AMPs) constitute essential intermediates of protein biosynthesis. Their polymerization in aqueous solution has often been claimed as a potential route to abiotic peptides in spite of a highly efficient CO2-promoted pathway of hydrolysis. Here we investigate the efficiency and relevance of this frequently overlooked pathway from model amino acid phosphate mixed anhydrides including aa-AMPs. Its predominance was demonstrated at CO2 concentrations matching that of physiological fluids or that of the present-day ocean, making a direct polymerization pathway unlikely. By contrast, the occurrence of the CO2-promoted pathway was observed to increase the efficiency of peptide bond formation owing to the high reactivity of the N-carboxyanhydride (NCA) intermediate. Even considering CO2 concentrations in early Earth liquid environments equivalent to present levels, mixed anhydrides would have polymerized predominantly through NCAs. The issue of a potential involvement of NCAs as biochemical metabolites could even be raised. The formation of peptide-phosphate mixed anhydrides from 5(4H)-oxazolones (transiently formed through prebiotically relevant peptide activation pathways) was also observed as well as the occurrence of the reverse cyclization process in the reactions of these mixed anhydrides. These processes constitute the core of a reaction network that could potentially have evolved towards the emergence of translation.

  4. Relationship between stimulated phosphatidic acid production and inositol lipid hydrolysis in intestinal longitudinal smooth muscle from guinea pig.

    PubMed

    Mallows, R S; Bolton, T B

    1987-06-15

    Accumulation of [32P]phosphatidic acid (PA) and total [3H]inositol phosphates (IPs) was measured in the longitudinal smooth-muscle layer from guinea-pig small intestine. Stimulation with carbachol, histamine and substance P produced increases in accumulation of both [3H]IPs and [32P]PA over the same concentration range. The increase in [32P]PA accumulation in response to carbachol (1 microM-0.1 mM) was inhibited in the presence of atropine (0.5 microM). Buffering the external free [Ca2+] to 10 nM did not prevent the carbachol-stimulated increase in [32P]PA accumulation. Carbachol and Ca2+ appear to act synergistically to increase accumulation of [32P]PA. In contrast, although incubation with noradrenaline also increased accumulation of [3H]IPs, no increase in accumulation of [32P]PA could be detected. These results suggest that an increase in formation of IPs is not necessarily accompanied by an increase in PA formation, and imply the existence of receptor-modulated pathways regulating PA concentrations other than by phospholipase-C-catalysed inositol phospholipid hydrolysis.

  5. Evaluation of xylitol production using corncob hemicellulosic hydrolysate by combining tetrabutylammonium hydroxide extraction with dilute acid hydrolysis.

    PubMed

    Jia, Honghua; Shao, Tingting; Zhong, Chao; Li, Hengxiang; Jiang, Min; Zhou, Hua; Wei, Ping

    2016-10-20

    In this paper, we produced hemicellulosic hydrolysate from corncob by tetrabutylammonium hydroxide (TBAH) extraction and dilute acid hydrolysis combined, further evaluating the feasibility of the resultant corncob hemicellulosic hydrolysate used in xylitol production by Candida tropicalis. Optimized conditions for corncob hemicellulose extraction by TBAH was obtained via response surface methodology: time of 90min, temperature of 60°C, liquid/solid ratio of 12 (v/w), and TBAH concentration of 55%, resulting in a hemicellulose extraction of 80.07% under these conditions. The FT-IR spectrum of the extracted corncob hemicellulose is consistent with that of birchwood hemicellulose and exhibits specific absorbance of hemicelluloses at 1380, 1168, 1050, and 900cm(-1). In addition, we found that C. tropicalis can ferment the resulting corncob hemicellulosic hydrolysate with pH adjustment and activated charcoal treatment leading to a high xylitol yield and productivity of 0.77g/g and 2.45g/(Lh), respectively. PMID:27474613

  6. Capillary electrophoresis analysis of hydrolysis, isomerization and enantiomerization of aspartyl model tripeptides in acidic and alkaline solution.

    PubMed

    De Boni, Silvia; Scriba, Gerhard K E

    2007-01-01

    In order to investigate the degradation of two aspartyl tripeptides, Gly-Asp-PheNH2 and Phe-Asp-GlyNH2 in solution capillary, electrophoresis methods were developed and validated. Separation of most degradation products including those arising from isomerization and enantiomerization of the Asp residues was achieved in a 50 mM sodium phosphate buffer, pH 3.0. Resolution of comigrating compounds could be achieved by addition of cyclodextrins to the background electrolyte. For tripeptide derivatives the assays were linear in the range of 0.015-3.0 mmol/l. Some dipeptides and amino acids exhibited a narrower linear range due to low UV absorbance. The limits of detection were in the range of 0.005-0.1 mmol/l. Incubation of the model peptides was carried out at pH 2 and 10. At pH 2, degradation of the peptides proceeded via C-terminal deamidation and peptide backbone hydrolysis. In contrast, isomerization and enantiomerization were observed in combination with deamidation at pH 10. Generally, degradation of Phe-Asp-GlyNH2 proceeded faster compared to Gly-Asp-PheNH2 due to steric hindrance by the phenyl side chain.

  7. Validated Method for the Characterization and Quantification of Extractable and Nonextractable Ellagitannins after Acid Hydrolysis in Pomegranate Fruits, Juices, and Extracts.

    PubMed

    García-Villalba, Rocío; Espín, Juan Carlos; Aaby, Kjersti; Alasalvar, Cesarettin; Heinonen, Marina; Jacobs, Griet; Voorspoels, Stefan; Koivumäki, Tuuli; Kroon, Paul A; Pelvan, Ebru; Saha, Shikha; Tomás-Barberán, Francisco A

    2015-07-29

    Pomegranates are one of the main highly valuable sources of ellagitannins. Despite the potential health benefits of these compounds, reliable data on their content in pomegranates and derived extracts and food products is lacking, as it is usually underestimated due to their complexity, diversity, and lack of commercially available standards. This study describes a new method for the analysis of the extractable and nonextractable ellagitannins based on the quantification of the acid hydrolysis products that include ellagic acid, gallic acid, sanguisorbic acid dilactone, valoneic acid dilactone, and gallagic acid dilactone in pomegranate samples. The study also shows the occurrence of ellagitannin C-glycosides in pomegranates. The method was optimized using a pomegranate peel extract. To quantify nonextractable ellagitannins, freeze-dried pomegranate fruit samples were directly hydrolyzed with 4 M HCl in water at 90 °C for 24 h followed by extraction of the pellet with dimethyl sulfoxide/methanol (50:50, v/v). The method was validated and reproducibility was assessed by means of an interlaboratory trial, showing high reproducibility across six laboratories with relative standard deviations below 15%. Their applicability was demonstrated in several pomegranate extracts, different parts of pomegranate fruit (husk, peels, and mesocarp), and commercial juices. A large variability has been found in the ellagitannin content (150-750 mg of hydrolysis products/g) and type (gallagic acid/ellagic acid ratios between 4 and 0.15) of the 11 pomegranate extracts studied.

  8. Validated Method for the Characterization and Quantification of Extractable and Nonextractable Ellagitannins after Acid Hydrolysis in Pomegranate Fruits, Juices, and Extracts.

    PubMed

    García-Villalba, Rocío; Espín, Juan Carlos; Aaby, Kjersti; Alasalvar, Cesarettin; Heinonen, Marina; Jacobs, Griet; Voorspoels, Stefan; Koivumäki, Tuuli; Kroon, Paul A; Pelvan, Ebru; Saha, Shikha; Tomás-Barberán, Francisco A

    2015-07-29

    Pomegranates are one of the main highly valuable sources of ellagitannins. Despite the potential health benefits of these compounds, reliable data on their content in pomegranates and derived extracts and food products is lacking, as it is usually underestimated due to their complexity, diversity, and lack of commercially available standards. This study describes a new method for the analysis of the extractable and nonextractable ellagitannins based on the quantification of the acid hydrolysis products that include ellagic acid, gallic acid, sanguisorbic acid dilactone, valoneic acid dilactone, and gallagic acid dilactone in pomegranate samples. The study also shows the occurrence of ellagitannin C-glycosides in pomegranates. The method was optimized using a pomegranate peel extract. To quantify nonextractable ellagitannins, freeze-dried pomegranate fruit samples were directly hydrolyzed with 4 M HCl in water at 90 °C for 24 h followed by extraction of the pellet with dimethyl sulfoxide/methanol (50:50, v/v). The method was validated and reproducibility was assessed by means of an interlaboratory trial, showing high reproducibility across six laboratories with relative standard deviations below 15%. Their applicability was demonstrated in several pomegranate extracts, different parts of pomegranate fruit (husk, peels, and mesocarp), and commercial juices. A large variability has been found in the ellagitannin content (150-750 mg of hydrolysis products/g) and type (gallagic acid/ellagic acid ratios between 4 and 0.15) of the 11 pomegranate extracts studied. PMID:26158321

  9. Gas-phase hydrolysis of triplet SO2: A possible direct route to atmospheric acid formation.

    PubMed

    Donaldson, D James; Kroll, Jay A; Vaida, Veronica

    2016-07-15

    Sulfur chemistry is of great interest to the atmospheric chemistry of several planets. In the presence of water, oxidized sulfur can lead to new particle formation, influencing climate in significant ways. Observations of sulfur compounds in planetary atmospheres when compared with model results suggest that there are missing chemical mechanisms. Here we propose a novel mechanism for the formation of sulfurous acid, which may act as a seed for new particle formation. In this proposed mechanism, the lowest triplet state of SO2 ((3)B1), which may be accessed by near-UV solar excitation of SO2 to its excited (1)B1 state followed by rapid intersystem crossing, reacts directly with water to form H2SO3 in the gas phase. For ground state SO2, this reaction is endothermic and has a very high activation barrier; our quantum chemical calculations point to a facile reaction being possible in the triplet state of SO2. This hygroscopic H2SO3 molecule may act as a condensation nucleus for water, giving rise to facile new particle formation (NPF).

  10. Gas-phase hydrolysis of triplet SO2: A possible direct route to atmospheric acid formation

    NASA Astrophysics Data System (ADS)

    Donaldson, D. James; Kroll, Jay A.; Vaida, Veronica

    2016-07-01

    Sulfur chemistry is of great interest to the atmospheric chemistry of several planets. In the presence of water, oxidized sulfur can lead to new particle formation, influencing climate in significant ways. Observations of sulfur compounds in planetary atmospheres when compared with model results suggest that there are missing chemical mechanisms. Here we propose a novel mechanism for the formation of sulfurous acid, which may act as a seed for new particle formation. In this proposed mechanism, the lowest triplet state of SO2 (3B1), which may be accessed by near-UV solar excitation of SO2 to its excited 1B1 state followed by rapid intersystem crossing, reacts directly with water to form H2SO3 in the gas phase. For ground state SO2, this reaction is endothermic and has a very high activation barrier; our quantum chemical calculations point to a facile reaction being possible in the triplet state of SO2. This hygroscopic H2SO3 molecule may act as a condensation nucleus for water, giving rise to facile new particle formation (NPF).

  11. Gas-phase hydrolysis of triplet SO2: A possible direct route to atmospheric acid formation

    PubMed Central

    Donaldson, D. James; Kroll, Jay A.; Vaida, Veronica

    2016-01-01

    Sulfur chemistry is of great interest to the atmospheric chemistry of several planets. In the presence of water, oxidized sulfur can lead to new particle formation, influencing climate in significant ways. Observations of sulfur compounds in planetary atmospheres when compared with model results suggest that there are missing chemical mechanisms. Here we propose a novel mechanism for the formation of sulfurous acid, which may act as a seed for new particle formation. In this proposed mechanism, the lowest triplet state of SO2 (3B1), which may be accessed by near-UV solar excitation of SO2 to its excited 1B1 state followed by rapid intersystem crossing, reacts directly with water to form H2SO3 in the gas phase. For ground state SO2, this reaction is endothermic and has a very high activation barrier; our quantum chemical calculations point to a facile reaction being possible in the triplet state of SO2. This hygroscopic H2SO3 molecule may act as a condensation nucleus for water, giving rise to facile new particle formation (NPF). PMID:27417675

  12. Gas-phase hydrolysis of triplet SO2: A possible direct route to atmospheric acid formation.

    PubMed

    Donaldson, D James; Kroll, Jay A; Vaida, Veronica

    2016-01-01

    Sulfur chemistry is of great interest to the atmospheric chemistry of several planets. In the presence of water, oxidized sulfur can lead to new particle formation, influencing climate in significant ways. Observations of sulfur compounds in planetary atmospheres when compared with model results suggest that there are missing chemical mechanisms. Here we propose a novel mechanism for the formation of sulfurous acid, which may act as a seed for new particle formation. In this proposed mechanism, the lowest triplet state of SO2 ((3)B1), which may be accessed by near-UV solar excitation of SO2 to its excited (1)B1 state followed by rapid intersystem crossing, reacts directly with water to form H2SO3 in the gas phase. For ground state SO2, this reaction is endothermic and has a very high activation barrier; our quantum chemical calculations point to a facile reaction being possible in the triplet state of SO2. This hygroscopic H2SO3 molecule may act as a condensation nucleus for water, giving rise to facile new particle formation (NPF). PMID:27417675

  13. /sup 18/O isotope effect in /sup 13/C nuclear magnetic resonance spectroscopy. Part 9. Hydrolysis of benzyl phosphate by phosphatase enzymes and in acidic aqueous solutions

    SciTech Connect

    Parente, J.E.; Risley, J.M.; Van Etten, R.L.

    1984-12-26

    The /sup 18/O isotope-induced shifts in /sup 13/C and /sup 31/P nuclear magnetic resonance (NMR) spectroscopy were used to establish the position of bond cleavage in the phosphatase-catalyzed and acid-catalyzed hydrolysis reactions of benzyl phosphate. The application of the /sup 18/O-isotope effect in NMR spectroscopy affords a continuous, nondestructive assay method for following the kinetics and position of bond cleavage in the hydrolytic process. The technique provides advantages over most discontinuous methods in which the reaction components must be isolated and converted to volatile derivatives prior to analysis. In the present study, (..cap alpha..-/sup 13/C,ester-/sup 18/O)benzyl phosphate and (ester-/sup 18/O)benzyl phosphate were synthesized for use in enzymatic and nonenzymatic studies. Hydrolysis reactions catalyzed by the alkaline phosphatase from E. coli and by the acid phosphatases isolated from human prostate and human liver were all accompanied by cleavage of the substrate phosphorus-oxygen bond consistent with previously postulated mechanisms involving covalent phosphoenzyme intermediates. An extensive study of the acid-catalyzed hydrolysis of benzyl phosphate at 75/sup 0/C revealed that the site of bond cleavage is dependent on pH. At pH less than or equal to 1.3, the hydrolysis proceeds with C-O bond cleavage; at 1.3 < pH < 2.0, there is a mixture of C-O and P-O bond scission, the latter progressively predominating as the pH is raised; at pH greater than or equal to 2.0, the hydrolysis proceeds with exclusive P-O bond scission. (S)-(+)-(..cap alpha..-/sup 2/H)Benzyl phosphate was also synthesized. Hydrolysis of this chiral benzyl derivative demonstrated that the acid-catalyzed C-O bond scission of benzyl phosphate proceeds by an A-1 (S/sub N/1) mechanism with 70% racemization and 30% inversion at carbon. 37 references, 4 figures, 2 tables.

  14. Summary Report on Gamma Radiolysis of TBP/n-dodecane in the Presence of Nitric Acid Using the Radiolysis/Hydrolysis Test Loop

    SciTech Connect

    Dean R. Peterman; Bruce J. Mincher; Catherine L. Riddle; Richard D. Tillotson

    2010-08-01

    Design and installation has been completed for a state-of-the-art radiolysis/hydrolysis test loop system. The system is used to evaluate the effects of gamma radiolysis and acid hydrolysis on the stability and performance of solvent extraction process solvents. The test loop is comprised of two main sections; the solvent irradiation and hydrolysis loop and the solvent reconditioning loop. In the solvent irradiation and hydrolysis loop, aqueous and organic phases are mixed and circulated through a gamma irradiator until the desired absorbed dose is achieved. Irradiation of the mixed phases is more representative of actual conditions in a solvent extraction process. Additionally, the contact of the organic phase with the aqueous phase will subject the solvent components to hydrolysis. This hydrolysis can be accelerated by controlling the system at an elevated temperature. At defined intervals, the organic from the irradiation/hydrolysis loop will be transferred to the solvent reconditioning loop where the solvent is contacted with scrub, strip, and solvent wash solutions which simulate process flowsheet conditions. These two processes are repeated until the total desired dose is achieved. Since all viable solvent extraction components in an advanced fuel cycle must exhibit high radiolytic and hydrolytic stability, this test loop is not limited to any one solvent system but is applicable to all systems of interest. Also, the test loop is not limited to testing of process flowsheets. It is also a valuable tool in support of fundamental research on newly identified extractants/modifiers and the impact of gamma radiation on their stability in a dynamic environment. The investigation of the radiolysis of a TBP/n-dodecane process solvent in contact with aqueous nitric acid has been performed. These studies were intended to confirm/optimize the operability of the test loop system. Additionally, these data are directly applicable to numerous other solvent extraction

  15. Hydrolysis and volatile fatty acids accumulation of waste activated sludge enhanced by the combined use of nitrite and alkaline pH.

    PubMed

    Huang, Cheng; Liu, Congcong; Sun, Xiuyun; Sun, Yinglu; Li, Rui; Li, Jiansheng; Shen, Jinyou; Han, Weiqing; Liu, Xiaodong; Wang, Lianjun

    2015-12-01

    Volatile fatty acids (VFAs) production from anaerobic digestion of waste activated sludge (WAS) is often limited by the slow hydrolysis and/or poor substrate availability. Increased attention has been given to enhance the hydrolysis and acidification of WAS recently. This study presented an efficient and green strategy based on the combined use of nitrite pretreatment and alkaline pH to stimulate hydrolysis and VFA accumulation from WAS. Results showed that both proteins and polysaccharides increased in the presence of nitrite, indicating the enhancement of sludge solubilization and hydrolysis processes. Mechanism investigations showed that nitrite pretreatment could disintegrate the sludge particle and disperse extracellular polymeric substances (EPS). Then, anaerobic digestion tests demonstrated VFA production increased with nitrite treatment. The maximal VFA accumulation was achieved with 0.1 g N/L nitrite dosage and pH 10.0 at a sludge retention time (SRT) of 7 days, which was much higher VFA production in comparison with the blank, sole nitrite pretreatment, or sole pH 10. The potential analysis suggested that the combined nitrite pretreatment and alkaline pH is capable of enhancing WAS digestion with a great benefit for biological nutrient removal (BNR).

  16. Synthesis, chemical and enzymatic hydrolysis, and aqueous solubility of amino acid ester prodrugs of 3-carboranyl thymidine analogs for boron neutron capture therapy of brain tumors.

    PubMed

    Hasabelnaby, Sherifa; Goudah, Ayman; Agarwal, Hitesh K; abd Alla, Mosaad S M; Tjarks, Werner

    2012-09-01

    Various water-soluble L-valine-, L-glutamate-, and glycine ester prodrugs of two 3-Carboranyl Thymidine Analogs (3-CTAs), designated N5 and N5-2OH, were synthesized for Boron Neutron Capture Therapy (BNCT) of brain tumors since the water solubilities of the parental compounds proved to be insufficient in preclinical studies. The amino acid ester prodrugs were prepared and stored as hydrochloride salts. The water solubilities of these amino acid ester prodrugs, evaluated in phosphate buffered saline (PBS) at pH 5, pH 6 and pH 7.4, improved 48-6600 times compared with parental N5 and N5-2OH. The stability of the amino acid ester prodrugs was evaluated in PBS at pH 7.4, Bovine serum, and Bovine cerebrospinal fluid (CSF). The rate of the hydrolysis in all three incubation media depended primarily on the amino acid promoiety and, to a lesser extend, on the site of esterification at the deoxyribose portion of the 3-CTAs. In general, 3'-amino acid ester prodrugs were less sensitive to chemical and enzymatic hydrolysis than 5'-amino acid ester prodrugs and the stabilities of the latter decreased in the following order: 5'-valine > 5'-glutamate > 5'-glycine. The rate of the hydrolysis of the 5'-amino acid ester prodrugs in Bovine CSF was overall higher than in PBS and somewhat lower than in Bovine serum. Overall, 5'-glutamate ester prodrug of N5 and the 5'-glycine ester prodrugs of N5 and N5-2OH appeared to be the most promising candidates for preclinical BNCT studies. PMID:22889558

  17. A process economic approach to develop a dilute-acid cellulose hydrolysis process to produce ethanol from biomass.

    PubMed

    Nagle, N; Ibsen, K; Jennings, E

    1999-01-01

    Successful deployment of a bioethanol process depends on the integration of technologies that can be economically commercialized. Pretreatment and fermentation operations of the traditional enzymatic bioethanol-production process constitute the largest portion of the capital and operating costs. Cost reduction in these areas, through improved reactions and reduced capital, will improve the economic feasibility of a large-scale plant. A technoeconomic model was developed using the ASPEN Plus modeling software package. This model included a two-stage pretreatment operation with a co-current first stage and countercurrent second stage, a lignin adsorption unit, and a cofermentation unit. Data from kinetic modeling of the pretreatment reactions, verified by bench-scale experiments, were used to create the ASPEN Plus base model. Results from the initial pretreatment and fermentation yields of the two-stage system correlated well to the performance targets established by the model. The ASPEN Plus model determined mass and energy-balance information, which was supplied to an economic module to determine the required selling price of the ethanol. Several pretreatment process variables such as glucose yield, liquid: solid ratio, additional pretreatment stages, and lignin adsorption were varied to determine which parameters had the greatest effect on the process economics. Optimized values for these key variables became target values for the bench-scale research, either to achieve or identify as potential obstacles in the future commercialization process. Results from this modeling and experimentation sequence have led to the design of an advanced two-stage engineering- scale reactor for a dilute-acid hydrolysis process.

  18. Design of experiments, a powerful tool for method development in forensic toxicology: application to the optimization of urinary morphine 3-glucuronide acid hydrolysis.

    PubMed

    Costa, S; Barroso, M; Castañera, A; Dias, M

    2010-04-01

    The application of the design of experiments to optimize method development in the field of forensic toxicology using the urinary morphine 3-glucuronide acid hydrolysis as an example is described. Morphine and its trideuterated analogue (used as an internal standard) were extracted from urine samples by liquid-liquid extraction (ToxiTubes A) and derivatized by silylation. Chromatographic analysis was done by gas chromatography-mass spectrometry in the selected ion monitoring mode. Using the peak area ratio (morphine-to-internal standard) as the response, we investigated the independent variables that could influence the acid hydrolysis, including temperature (range 70-130 degrees C), acid volume (range 500-1,000 microL) and time (range 15-90 min). A 2(3) full factorial design for the screening and a response surface methodology, including a central composite design for optimization, were applied. The factors which influenced the response to a greater extent were temperature and its interaction both with time and acid volume. By application of a multiple regression analysis to the experimental data, a second-order polynomial equation was obtained. The optimal predicted conditions for morphine 3-glucuronide acid hydrolysis were 115 degrees C, 38 min and 500 microL for temperature, time and acid volume, respectively. Using design of experiments, instead of the one factor at a time approach, we achieved the optimum combination of all factor values, and this allowed the best results to be obtained, simultaneously optimizing resources. In addition, time and money can be saved, since other approaches are in general more time-consuming and laborious, and do not take into account the interactions between factors.

  19. The enhancement of the hydrolysis of bamboo biomass in ionic liquid with chitosan-based solid acid catalysts immobilized with metal ions.

    PubMed

    Cheng, Jie; Wang, Nan; Zhao, Dezhou; Qin, Dandan; Si, Wenqing; Tan, Yunfei; Wei, Shun'an; Wang, Dan

    2016-11-01

    Three kinds of sulfonated cross-linked chitosan (SCCR) immobilized with metal ions of Cu(2+), Fe(3+) and Zn(2+) individually were synthesized and firstly used as solid acid catalysts in the hydrolysis of bamboo biomass. FTIR spectra showed that metal ions had been introduced into SCCR and the N-metal ions coordinate bound was formed. The particle sizes of these catalysts were about 500-1000μm with a pore size of 50-160μm. All of the three kinds of catalysts performed well for bamboo hydrolysis with 1-butyl-3-methyl-imidazolium chloride used as solvent. The most effective one was sulfonated cross-linked chitosan immobilized with Fe(3+) (Fe(3+)-SCCR). TRS yields were up to 73.42% for hydrolysis of bamboo powder in [C4mim]Cl with Fe(3+)-SCCR at 120°C and 20RPM after 24h. These novel chitosan-based metal ions immobilized solid acid catalysts with ionic liquids as the solvent might be promising to facilitate cost-efficient conversion of biomass into biofuels and bioproducts. PMID:27611029

  20. The enhancement of the hydrolysis of bamboo biomass in ionic liquid with chitosan-based solid acid catalysts immobilized with metal ions.

    PubMed

    Cheng, Jie; Wang, Nan; Zhao, Dezhou; Qin, Dandan; Si, Wenqing; Tan, Yunfei; Wei, Shun'an; Wang, Dan

    2016-11-01

    Three kinds of sulfonated cross-linked chitosan (SCCR) immobilized with metal ions of Cu(2+), Fe(3+) and Zn(2+) individually were synthesized and firstly used as solid acid catalysts in the hydrolysis of bamboo biomass. FTIR spectra showed that metal ions had been introduced into SCCR and the N-metal ions coordinate bound was formed. The particle sizes of these catalysts were about 500-1000μm with a pore size of 50-160μm. All of the three kinds of catalysts performed well for bamboo hydrolysis with 1-butyl-3-methyl-imidazolium chloride used as solvent. The most effective one was sulfonated cross-linked chitosan immobilized with Fe(3+) (Fe(3+)-SCCR). TRS yields were up to 73.42% for hydrolysis of bamboo powder in [C4mim]Cl with Fe(3+)-SCCR at 120°C and 20RPM after 24h. These novel chitosan-based metal ions immobilized solid acid catalysts with ionic liquids as the solvent might be promising to facilitate cost-efficient conversion of biomass into biofuels and bioproducts.

  1. Isolation and structural characterization of sugarcane bagasse lignin after dilute phosphoric acid plus steam explosion pretreatment and its effect on cellulose hydrolysis.

    PubMed

    Zeng, Jijiao; Tong, Zhaohui; Wang, Letian; Zhu, J Y; Ingram, Lonnie

    2014-02-01

    The structure of lignin after dilute phosphoric acid plus steam explosion pretreatment process of sugarcane bagasse in a pilot scale and the effect of the lignin extracted by ethanol on subsequent cellulose hydrolysis were investigated. The lignin structural changes caused by pretreatment were identified using advanced nondestructive techniques such as gel permeation chromatography (GPC), quantitative (13)C, and 2-D nuclear magnetic resonance (NMR). The structural analysis revealed that ethanol extractable lignin preserved basic lignin structure, but had relatively lower amount of β-O-4 linkages, syringyl/guaiacyl units ratio (S/G), p-coumarate/ferulate ratio, and other ending structures. The results also indicated that approximately 8% of mass weight was extracted by pure ethanol. The bagasse after ethanol extraction had an approximate 22% higher glucose yield after enzyme hydrolysis compared to pretreated bagasse without extraction.

  2. Development of a solid-phase extraction method for simultaneous extraction of adipic acid, succinic acid and 1,4-butanediol formed during hydrolysis of poly(butylene adipate) and poly(butylene succinate).

    PubMed

    Lindström, Annika; Albertsson, Ann-Christine; Hakkarainen, Minna

    2004-01-01

    A solid-phase extraction (SPE) method was developed for the simultaneous extraction of dicarboxylic acids and diols formed during hydrolysis of poly(butylene succinate), PBS, and poly(butylene adipate), PBA. Four commercial non-polar SPE columns, three silica based: C8, C18, C18 (EC), and one resin based: ENV+, were tested for the extraction of succinic acid, adipic acid and 1,4-butanediol, the expected final hydrolysis products of PBS and PBA. ENV+ resin was chosen as a solid-phase, because it displayed the best extraction efficiency for 1,4-butanediol and succinic acid. Linear range for the extracted analytes was 1-500 ng/microl for adipic acid and 2-500 ng/microl for 1,4-butanediol and succinic acid. Detection and quantification limits for the analytes were between 1-2 and 2-7 ng/microl, respectively, and relative standard deviations were between 3 and 7%. Good repeatability and low detection limits made the developed SPE method and subsequent gas chromatography-mass spectrometry (GC-MS) analysis a sensitive tool for identification and quantification of hydrolysis products at early stages of degradation.

  3. A study of concentrated acid hydrolysis conversion of lignocellulosic materials to sugars using a co-rotating twin-screw reactor extruder and plug flow reactor

    NASA Astrophysics Data System (ADS)

    Miller, William Scott

    Concerns about the ability of petroleum to continue supplying ever increasing global energy demands, at a price capable of generating continued economic growth, have spurred innovative research in the field of alternative energy. One alternative energy option that has the ability to provide long-term sustainable energy supplies for the global energy market is the conversion of lignocellulosic materials, via acid hydrolysis, to fermentable sugars for the production of fuel grade ethanol. This research demonstrates the ability of a co-rotating twin-screw reactor extruder and plug flow reactor to continuously convert lignocellulosic materials to fermentable sugars using high temperature concentrated acid hydrolysis. In addition to demonstrating continuous operation of the two-stage concentrated acid hydrolysis system, a number of design of experiments were conducted to model the twin-screw performance and maximize its ability to effectively solubilize lignocellulosic feedstocks in the high shear, elevated temperature, concentrated acid environment. These studies produced a base case twin-screw operating condition used to generate a standard extrudate composition for an extensive high temperature acid hydrolysis batch reactor kinetic modeling study. In this study a number of nonlinear and linear regression analyses were undertaken so that the concentration of less resistant cellulose, or the amount of solublilized extrudate cellulose, resistant cellulose, or non-solubilized extrudate cellulose, glucose, and decomposition products could be obtained as a function of time, temperature, and acid concentration. This study demonstrated that the theoretical cellulose conversion of 51% was limited by the amount of solubilized polysaccharides that could be produced in the twin-screw pretreatment. Further experimentation, showing twin-screw pretreatment lignocellulosic versatility, produced nearly identical results as the southern yellow pine sawdust experiments that were

  4. Hydrolysis of Cellulose by a Mesoporous Carbon-Fe2(SO4)3/γ-Fe2O3 Nanoparticle-Based Solid Acid Catalyst

    PubMed Central

    Yamaguchi, Daizo; Watanabe, Koki; Fukumi, Shinya

    2016-01-01

    Carbon-based solid acid catalysts have shown significant potential in a wide range of applications, and they have been successfully synthesized using simple processes. Magnetically separable mesoporous carbon composites also have enormous potential, especially in separation and adsorption technology. However, existing techniques have been unable to produce a magnetically separable mesoporous solid acid catalyst because no suitable precursors have been identified. Herein we describe a magnetically separable, mesoporous solid acid catalyst synthesized from a newly developed mesoporous carbon-γ-Fe2O3 nanoparticle composite. This material exhibits an equivalent acid density and catalytic activity in the hydrolysis of microcrystalline cellulose, to that of the cellulose-derived conventional catalyst. Since it is magnetically separable, this material can be readily recovered and reused, potentially reducing the environmental impact of industrial processes to which it is applied. PMID:26856604

  5. Review of methods used in lunar organic analysis - Extraction and hydrolysis techniques.

    NASA Technical Reports Server (NTRS)

    Kvenvolden, K. A.

    1972-01-01

    Extraction, hydrolysis, and crushing procedures have been useful in discovering some of the carbon compounds in lunar samples from the Apollo 11 and 12 missions. The nonaqueous solvent system used mostly in lunar sample work has been benzene:methanol. Two methods of extraction have been sonication and Soxhlet extraction, sonication appearing to be the preferred method. Extraction of lunar samples with water and acid hydrolysis of the water extract has proved to be the best method in the search for amino acids or their precursors. Direct acid hydrolysis of lunar samples provided evidence for the presence of carbides or carbide-like materials in lunar surface samples. Hydrolysis of lunar samples with DF, DC1, and NaOD has shown that methane and ethane are indigenous to the moon.

  6. Application of fast ultrasound water-bath assisted enzymatic hydrolysis--high performance liquid chromatography-inductively coupled plasma-mass spectrometry procedures for arsenic speciation in seafood materials.

    PubMed

    Moreda-Piñeiro, Antonio; Moreda-Piñeiro, Jorge; Herbello-Hermelo, Paloma; Bermejo-Barrera, Pilar; Muniategui-Lorenzo, Soledad; López-Mahía, Purificación; Prada-Rodríguez, Darío

    2011-09-28

    Enzymatic hydrolysis of seafood materials for isolating arsenic species (As(III), As(V), DMA and AsB) has been successfully performed by assisting the procedure with ultrasound energy (35 kHz) supplied by an ultrasound water-bath. The use of pepsin, as a proteolytic enzyme, under optimized operating conditions (pH 3.0, temperature 40°C, enzyme to sample ratio of 0.3) led to an efficient assistance of the enzymatic process in a short period of time (from 4.0 to 30 min). The enzymatic extract was then subjected to a clean-up procedure based on ENVI-Carb™ solid phase extraction (SPE). An optimized anion exchange high performance liquid chromatography (HPLC) coupled to inductively coupled plasma-mass spectrometry (ICP-MS) permitted the fast separation (less than 15 min) of six different arsenic species (arsenite, As(III); arsenate, As(V); dimethylarsinic acid, DMA; and arsenobetaine, AsB; as well as monomethylarsonic acid, MMA; and arsenocholine, AsC) in a single run. Relative standard deviations (n=11) of the over-all procedure were 7% for AsB and DMA, 11% for As(III) and 9% for MMA. HPLC-ICP-MS determinations were performed using aqueous calibrations covering arsenic concentrations of 0, 5, 10, 25, 100 and 200 μg L(-1) (expressed as arsenic) for As(III), As(V), MMA, DMA and AsC; and 0, 125, 250, 500, 750, 1000 and 2000 μg L(-1) (expressed as arsenic) for AsB. Germanium (5 μg L(-1)) was used as an internal standard. Analytical recoveries from the anion exchange column varied from 96 to 105% (enzymatic digests spiked with low target concentrations), from 97 to 104% (enzymatic digests spiked with intermediate target concentrations), and from 98 to 103% (enzymatic digests spiked with high target concentrations). The developed method was successfully applied to two certified reference materials (CRMs), DORM-2 and BCR 627, which offer certified AsB and DMA contents, and also to different seafood samples (mollusks, white fish and cold water fish). Good agreement

  7. Influence of the nature of titanium alkoxide and of the acid of hydrolysis in the preparation of titanium-pillared montmorillonites

    NASA Astrophysics Data System (ADS)

    Del Castillo, H. L.; Gil, A.; Grange, P.

    1997-07-01

    Titanium-pillared montmorillonites using Ti(OC2H5)4, Ti(O-nC3H7)4, Ti(O-iC3H7)4 and Ti(O-nC4H,)4 as sources of titanium, and HCl, HClO4, HNO3, H2SO4, CH3CO2H and H3PO4 as acids for hydrolysis, have been prepared. The preparation of titanium-pillared clays (Ti-PILCS) is mainly affected by the acid/alkoxide mole ratio. The nature of the alkoxide influences both the basal spacing and the specific surface area. The use of Ti(OC2H5)4 as a source of titanium yielded the best textural and thermal stability results. The differences observed in the titanium-pillared clays as a function of the acid used for the hydrolysis seem to be mainly related to the pH of the solution of intercalation.

  8. Computational chemistry study of the environmentally important acid-catalyzed hydrolysis of atrazine and related 2-chloro-s-triazines.

    PubMed

    Sawunyama, Phillip; Bailey, George W

    2002-08-01

    Many chlorine-containing pesticides, for example 2-chloro-s-triazines, are of great concern both environmentally and toxicologically. As a result, ascertaining or predicting the fate and transport of these compounds in soils and water is of current interest. Transformation pathways for 2-chloro-s-triazines in the environment include dealkylation, dechlorination (hydrolysis), and ring cleavage. This study explored the feasibility of using computational chemistry, specifically the hybrid density functional theory method, B3LYP, to predict hydrolysis trends of atrazine (2-chloro-N4-ethyl-N6-isopropyl-1,3,5-triazine-2,4-diamine) and related 2-chloro-s-triazines to the corresponding 2-hydroxy-s-triazines. Gas-phase energetics are described on the basis of calculations performed at the B3LYP/6-311++G(d,p)//B3LYP/6-31G* level of theory. Calculated free energies of hydrolysis (delta h G298) are nearly the same for simazine (2-chloro-N4,N6-diethyl-1,3,5-triazine-2,4-diamine), atrazine, and propazine (2-chloro-N4,N6-di-isopropyl-1,3,5-triazine-2,4-diamine), suggesting that hydrolysis is not significantly affected by the side-chain amine-nitrogen alkyl substituents. High-energy barriers also suggest that the reactions are not likely to be observed in the gas phase. Aqueous solvation effects were examined by means of self-consistent reaction field methods (SCRF). Molecular structures were optimized at the B3LYP/6-31G* level using the Onsager model, and solvation energies were calculated at the B3LYP/6-311++G(d,p) level using the isodensity surface polarizable continuum model (IPCM). Although the extent of solvent stabilization was greater for cationic species than neutral ones, the full extent of solvation is underestimated, especially for the transition state structures. As a consequence, the calculated hydrolysis barrier for protonated atrazine is exaggerated compared with the experimentally determined one. Overall, the hydrolysis reactions follow a concerted nucleophilic

  9. Influence of protein composition and hydrolysis method on intestinal absorption of protein in man.

    PubMed

    Keohane, P P; Grimble, G K; Brown, B; Spiller, R C; Silk, D B

    1985-09-01

    An intestinal perfusion technique has been used in normal human subjects to investigate the influence that starter protein composition and hydrolysis procedure have on absorption of amino acid residues from partial enzymic hydrolysates of whole protein. Five starter proteins were studied. Three (egg albumin, casein/soy/lactalbumin, and lactalbumin) were hydrolysed by papain, a second lactalbumin starter protein, and a meat/soy/lactalbumin blend were hydrolysed by a porcine pancreatic enzyme system. Irrespective of starter protein composition or hydrolysis method used, four amino acid residues (threonine, glutamic acid, phenylalanine, and histidine) were absorbed significantly faster from all hydrolysates compared with absorption from their equivalent free amino acid mixtures. In contrast, both starter protein composition and hydrolysis method influenced absorption characteristics of up to nine other amino acid residues. PMID:4029718

  10. Joint action of ultrasonic and Fe³⁺ to improve selectivity of acid hydrolysis for microcrystalline cellulose.

    PubMed

    Li, Jinbao; Qiang, Dandan; Zhang, Meiyun; Xiu, Huijuan; Zhang, Xiangrong

    2015-09-20

    In this study, the combination of Fe(3+)/HCl and ultrasonic treatment was applied to selectively hydrolyze cellulose for the preparation of microcrystalline cellulose (MCC). It was found that the crystallinity and specific surface area of hydrocellulose samples were higher (78.92% and 2.23581 m(2)g(-1), respectively), compared with the method that only used Fe(3+)/HCl catalyst without ultrasonic treatment. Meanwhile, the hydrolysate can be extracted and reused for cellulose hydrolysis for three runs, which was effective in saving the dosage of chemicals and reducing the pollution of the environment without affecting the properties of hydrocellulose. Moreover, the increased concentration of total reducing sugar (TRS) after three runs may be used as a valuable source in biofuels production. The technology of cellulose hydrolysis, by retaining the crystalline region for MCC products while promoting hydrolysis of amorphous region for further utilization is of great novelty, which may prove valuable in converting biomass into chemicals and biofuels, environmentally and economically.

  11. Joint action of ultrasonic and Fe³⁺ to improve selectivity of acid hydrolysis for microcrystalline cellulose.

    PubMed

    Li, Jinbao; Qiang, Dandan; Zhang, Meiyun; Xiu, Huijuan; Zhang, Xiangrong

    2015-09-20

    In this study, the combination of Fe(3+)/HCl and ultrasonic treatment was applied to selectively hydrolyze cellulose for the preparation of microcrystalline cellulose (MCC). It was found that the crystallinity and specific surface area of hydrocellulose samples were higher (78.92% and 2.23581 m(2)g(-1), respectively), compared with the method that only used Fe(3+)/HCl catalyst without ultrasonic treatment. Meanwhile, the hydrolysate can be extracted and reused for cellulose hydrolysis for three runs, which was effective in saving the dosage of chemicals and reducing the pollution of the environment without affecting the properties of hydrocellulose. Moreover, the increased concentration of total reducing sugar (TRS) after three runs may be used as a valuable source in biofuels production. The technology of cellulose hydrolysis, by retaining the crystalline region for MCC products while promoting hydrolysis of amorphous region for further utilization is of great novelty, which may prove valuable in converting biomass into chemicals and biofuels, environmentally and economically. PMID:26050886

  12. Chemometrics-assisted Spectrofluorimetric Determination of Two Co-administered Drugs of Major Interaction, Methotrexate and Aspirin, in Human Urine Following Acid-induced Hydrolysis.

    PubMed

    Maher, Hadir M; Ragab, Marwa A A; El-Kimary, Eman I

    2015-01-01

    Methotrexate (MTX) is widely used to treat rheumatoid arthritis (RA), mostly along with non-steroidal anti-inflammatory drugs (NSAIDs), the most common of which is aspirin or acetyl salicylic acid (ASA). Since NSAIDs impair MTX clearance and increase its toxicity, it was necessary to develop a simple and reliable method for the monitoring of MTX levels in urine samples, when coadministered with ASA. The method was based on the spectrofluorimetric measurement of the acid-induced hydrolysis product of MTX, 4-amino-4-deoxy-10-methylpteroic acid (AMP), along with the strongly fluorescent salicylic acid (SA), a product of acid-induced hydrolysis of aspirin and its metabolites in urine. The overlapping emission spectra were resolved using the derivative method (D method). In addition, the corresponding derivative emission spectra were convoluted using discrete Fourier functions, 8-points sin xi polynomials, (D/FF method) for better elimination of interferences. Validation of the developed methods was carried out according to the ICH guidelines. Moreover, the data obtained using derivative and convoluted derivative spectra were treated using the non-parametric Theil's method (NP), compared with the least-squares parametric regression method (LSP). The results treated with Theil's method were more accurate and precise compared with LSP since the former is less affected by the outliers. This work offers the potential of both derivative and convolution using discrete Fourier functions in addition to the effectiveness of using the NP regression analysis of data. The high sensitivity obtained by the proposed methods was promising for measuring low concentration levels of the two drugs in urine samples. These methods were efficiently used to measure the drugs in human urine samples following their co-administration. PMID:26234512

  13. Enteric-coated capsule containing β-galactosidase-loaded polylactic acid nanocapsules: enzyme stability and milk lactose hydrolysis under simulated gastrointestinal conditions.

    PubMed

    He, Hongjun; Zhang, Xueting; Sheng, Yan

    2014-11-01

    In order to protect peroral β-galactosidase from being degraded and hydrolyse milk lactose efficiently in the environments of gastrointestinal tract, a double-capsule delivery system composed of enteric-coated capsule and polylactic acid (PLA) nanocapsules (NCs) was developed for encapsulation of β-galactosidase. β-galactosidase-loaded PLA NCs in the size range of 100-200 nm were prepared by a modified w1/o/w2 technique. During the encapsulation process, dichloromethane/ethyl acetate (1 : 1, v/v) as the solvent composition, high-pressure homogenisation (150 bar, 3 min) as the second emulsification method and polyvinyl alcohol or Poloxamer 188 as a stabiliser in the inner phase could efficiently improve the activity retention of β-galactosidase (>90%). Subsequently, the prepared NCs were freeze-dried and filled in a hydroxypropyl methylcellulose phthalate (HP55)-coated capsule. In vitro results revealed that the HP55-coated capsule remained intact in the simulated gastric fluid and efficiently protected the nested β-galactosidase from acidic denaturation. Under the simulated intestinal condition, the enteric coating dissolved rapidly and released the β-galactosidase-loaded PLA NCs, which exhibited greater stability against enzymatic degradation and higher hydrolysis ratio (∼100%) towards milk lactose than the free β-galactosidase. These results suggest that this double-capsule delivery system represents promising candidate for efficient lactose hydrolysis in the gastrointestinal tract.

  14. The use of sub-critical water hydrolysis for the recovery of peptides and free amino acids from food processing wastes. Review of sources and main parameters.

    PubMed

    Marcet, Ismael; Álvarez, Carlos; Paredes, Benjamín; Díaz, Mario

    2016-03-01

    Food industry processing wastes are produced in enormous amounts every year, such wastes are usually disposed with the corresponding economical cost it implies, in the best scenario they can be used for pet food or composting. However new promising technologies and tools have been developed in the last years aimed at recovering valuable compounds from this type of materials. In particular, sub-critical water hydrolysis (SWH) has been revealed as an interesting way for recovering high added-value molecules, and its applications have been broadly referred in the bibliography. Special interest has been focused on recovering protein hydrolysates in form of peptides or amino acids, from both animal and vegetable wastes, by means of SWH. These recovered biomolecules have a capital importance in fields such as biotechnology research, nutraceuticals, and above all in food industry, where such products can be applied with very different objectives. Present work reviews the current state of art of using sub-critical water hydrolysis for protein recovering from food industry wastes. Key parameters as reaction time, temperature, amino acid degradation and kinetic constants have been discussed. Besides, the characteristics of the raw material and the type of products that can be obtained depending on the substrate have been reviewed. Finally, the application of these hydrolysates based on their functional properties and antioxidant activity is described. PMID:26831563

  15. The use of sub-critical water hydrolysis for the recovery of peptides and free amino acids from food processing wastes. Review of sources and main parameters.

    PubMed

    Marcet, Ismael; Álvarez, Carlos; Paredes, Benjamín; Díaz, Mario

    2016-03-01

    Food industry processing wastes are produced in enormous amounts every year, such wastes are usually disposed with the corresponding economical cost it implies, in the best scenario they can be used for pet food or composting. However new promising technologies and tools have been developed in the last years aimed at recovering valuable compounds from this type of materials. In particular, sub-critical water hydrolysis (SWH) has been revealed as an interesting way for recovering high added-value molecules, and its applications have been broadly referred in the bibliography. Special interest has been focused on recovering protein hydrolysates in form of peptides or amino acids, from both animal and vegetable wastes, by means of SWH. These recovered biomolecules have a capital importance in fields such as biotechnology research, nutraceuticals, and above all in food industry, where such products can be applied with very different objectives. Present work reviews the current state of art of using sub-critical water hydrolysis for protein recovering from food industry wastes. Key parameters as reaction time, temperature, amino acid degradation and kinetic constants have been discussed. Besides, the characteristics of the raw material and the type of products that can be obtained depending on the substrate have been reviewed. Finally, the application of these hydrolysates based on their functional properties and antioxidant activity is described.

  16. Hydrolysis reactor for hydrogen production

    DOEpatents

    Davis, Thomas A.; Matthews, Michael A.

    2012-12-04

    In accordance with certain embodiments of the present disclosure, a method for hydrolysis of a chemical hydride is provided. The method includes adding a chemical hydride to a reaction chamber and exposing the chemical hydride in the reaction chamber to a temperature of at least about 100.degree. C. in the presence of water and in the absence of an acid or a heterogeneous catalyst, wherein the chemical hydride undergoes hydrolysis to form hydrogen gas and a byproduct material.

  17. One-pot enzymatic synthesis of docosahexaenoic acid-rich triacylglycerols at the sn-1(3) position using by-product from selective hydrolysis of tuna oil.

    PubMed

    Nagao, Toshihiro; Watanabe, Yomi; Maruyama, Kazuaki; Momokawa, Yuusuke; Kishimoto, Noriaki; Shimada, Yuji

    2011-01-31

    Docosahexaenoic acid (DHA)-rich oil has been industrially produced by selective hydrolysis of tuna oil with a lipase that acts weakly on DHA. The free fatty acids (FFAs) generated in this process as by-products contain a high DHA concentration (46wt%) but are treated as industrial waste. This study attempted to reuse these by-product FFAs using a one-pot process, and succeeded in producing triacylglycerols (TAGs) through the esterification of the by-product FFAs with glycerol using immobilized Rhizomucor miehei lipase. Regiospecific analysis of the resulting TAGs showed that the content of DHA at the sn-1(3) position (51.7mol%) was higher than the content of DHA at the sn-2 position (17.3mol%). The DHA distribution in TAGs synthesized in this study was similar to the DHA distribution in TAGs from seal oil.

  18. Determination of Total Carbohydrates in Algal Biomass: Laboratory Analytical Procedure (LAP)

    SciTech Connect

    Van Wychen, S.; Laurens, L. M. L.

    2013-12-01

    This procedure uses two-step sulfuric acid hydrolysis to hydrolyze the polymeric forms of carbohydrates in algal biomass into monomeric subunits. The monomers are then quantified by either HPLC or a suitable spectrophotometric method.

  19. A single amino acid residue determines the ratio of hydrolysis to transglycosylation catalyzed by β-glucosidases.

    PubMed

    Frutuoso, M A; Marana, S R

    2013-01-01

    The propensity to catalysis of transglycosylation of the β-glucosidase Tmβgly is higher than for Sfβgly. Moreover the propensity to catalysis of transglycosylation is directly proportional to the substrate concentration for Tmβgly, whereas for Sfβgly it is constant. For instance, 60% of a Tmβgly sample catalyzes transglycosylation reactions at 40 mM p-nitrophenyl β-glucoside, whereas only 40% is engaged in hydrolysis of this substrate. For Sfβgly the fraction involved in transglycosylation is only 30 %. In addition, 48 % of a Tmβgly sample catalyzes transglycosylation reactions at 8 mM methylumbelliferyl β-glucoside, whereas Sfβgly does not catalyze transglycosylation using this substrate. Interestingly, these Tmβgly properties were grafted into Sfβgly by a single replacement of a residue forming a channel involved in supplying the catalytic water molecules for attack on the covalent intermediate present in the reaction catalyzed by β-glucosidases. Hence a single residue determines the ratio of hydrolysis to transglycosylation reactions catalyzed by these β-glucosidases.

  20. Fermentative l-lactic acid production from pretreated whole slurry of oil palm trunk treated by hydrothermolysis and subsequent enzymatic hydrolysis.

    PubMed

    Eom, In-Yong; Oh, Young-Hoon; Park, Si Jae; Lee, Seung-Hwan; Yu, Ju-Hyun

    2015-06-01

    A simple and cost-effective biochemical conversion process consisting of hydrothermal treatment, enzymatic hydrolysis and fermentation of pretreated whole slurry (PWS) was developed for producing l-lactic acid (L-LA) from oil palm trunk (OPT). When OPT was hydrothermally treated at optimal condition capable of achieving maximum yield of hemicellulosic sugars after enzymatic hydrolysis, the enzymatic digestibility of the PWS afforded a yield of 81.4% of the theoretical glucose yield (TGY). However, glucose yield from washed pretreated solid (WPS) was only 43.5% of TGY. The use of two hydrolysates from PWS and WPS for fermentation by Lactobacillus paracasei engineered to selectively produce L-LA afforded yields of 89.5% and 45.8% of the theoretical LA yield (TLY), respectively. This study confirmed the inevitable extensive sugar loss during washing of pretreated slurry due to loss of soluble starch. Alternatively, the proposed design process is considered suitable for converting OPT to L-LA without such starch loss.

  1. Enzymatic hydrolysis of fructans in the tequila production process.

    PubMed

    Avila-Fernández, Angela; Rendón-Poujol, Xóchitl; Olvera, Clarita; González, Fernando; Capella, Santiago; Peña-Alvarez, Araceli; López-Munguía, Agustín

    2009-06-24

    In contrast to the hydrolysis of reserve carbohydrates in most plant-derived alcoholic beverage processes carried out with enzymes, agave fructans in tequila production have traditionally been transformed to fermentable sugars through acid thermal hydrolysis. Experiments at the bench scale demonstrated that the extraction and hydrolysis of agave fructans can be carried out continuously using commercial inulinases in a countercurrent extraction process with shredded agave fibers. Difficulties in the temperature control of large extraction diffusers did not allow the scaling up of this procedure. Nevertheless, batch enzymatic hydrolysis of agave extracts obtained in diffusers operating at 60 and 90 degrees C was studied at the laboratory and industrial levels. The effects of the enzymatic process on some tequila congeners were studied, demonstrating that although a short thermal treatment is essential for the development of tequila's organoleptic characteristics, the fructan hydrolysis can be performed with enzymes without major modifications in the flavor or aroma, as determined by a plant sensory panel and corroborated by the analysis of tequila congeners.

  2. Efficient hydrolysis of corncob residue through cellulolytic enzymes from Trichoderma strain G26 and L-lactic acid preparation with the hydrolysate.

    PubMed

    Xie, Lulu; Zhao, Jin; Wu, Jian; Gao, Mingfu; Zhao, Zhewei; Lei, Xiangyun; Zhao, Yi; Yang, Wei; Gao, Xiaoxue; Ma, Cuiyun; Liu, Huanfei; Wu, Fengjuan; Wang, Xingxing; Zhang, Fengwei; Guo, Pengyuan; Dai, Guifu

    2015-10-01

    To prepare fermentable hydrolysate from corncob residue (CCR), Trichoderma strain G26 was cultured on medium containing CCR for production of cellulolytic enzymes through solid-state fermentation (SSF), resulting in 71.3 IU/g (FPA), 136.2 IU/g (CMCase), 85.1 IU/g (β-glucosidase) and 11,344 IU/g (xylanase), respectively. Through a three-stage saccharification strategy, CCR was hydrolyzed by the enzymatic solution (6.5 FPU/ml) into fermentable hydrolysate containing 60.1g/l glucose (81.2% cellulose was converted at solid loading of 12.5%), 21.4% higher than that by the one-stage method. And then the hydrolysate was used to produce L-lactic acid by a previous screened strain Bacillus coagulans ZX25 in the submerged fermentation. 52.0 g/l L-lactic acid was obtained after fermentation for 44 h, with 86.5% glucose being converted to L-lactic acid. The results indicate that the strains and the hydrolysis strategy are promising for commercial production of L-lactic acid from CCR and other biomass. PMID:26143000

  3. Hydrolysis-acidogenesis of food waste in solid-liquid-separating continuous stirred tank reactor (SLS-CSTR) for volatile organic acid production.

    PubMed

    Karthikeyan, Obulisamy Parthiba; Selvam, Ammaiyappan; Wong, Jonathan W C

    2016-01-01

    The use of conventional continuous stirred tank reactor (CSTR) can affect the methane (CH4) recovery in a two-stage anaerobic digestion of food waste (FW) due to carbon short circuiting in the hydrolysis-acidogenesis (Hy-Aci) stage. In this research, we have designed and tested a solid-liquid-separating CSTR (SLS-CSTR) for effective Hy-Aci of FW. The working conditions were pH 6 and 9 (SLS-CSTR-1 and -2, respectively); temperature-37°C; agitation-300rpm; and organic loading rate (OLR)-2gVSL(-1)day(-1). The volatile fatty acids (VFA), enzyme activities and bacterial population (by qPCR) were determined as test parameters. Results showed that the Hy-Aci of FW at pH 9 produced ∼35% excess VFA as compared to that at pH 6, with acetic and butyric acids as major precursors, which correlated with the high enzyme activities and low lactic acid bacteria. The design provided efficient solid-liquid separation there by improved the organic acid yields from FW.

  4. An enhanced procedure for measuring organic acids and methyl esters in PM2.5

    NASA Astrophysics Data System (ADS)

    Liu, F.; Duan, F. K.; He, K. B.; Ma, Y. L.; Rahn, K. A.; Zhang, Q.

    2015-11-01

    A solid-phase extraction (SPE) pretreatment procedure allowing organic acids to be separated from methyl esters in fine aerosol has been developed. The procedure first separates the organic acids from fatty acid methyl esters (FAMEs) and other nonacid organic compounds by aminopropyl-based SPE cartridge and then quantifies them by gas chromatography/mass spectrometry. The procedure prevents the fatty acids and dimethyl phthalate from being overestimated, and so allows us to accurately quantify the C4-C11 dicarboxylic acids (DCAs) and the C8-C30 monocarboxylic acids (MCAs). Results for the extraction of DCAs, MCAs, and AMAs in eluate and FAMEs in effluate by SAX and NH2 SPE cartridges exhibited that the NH2 SPE cartridge gave higher extraction efficiency than the SAX cartridge. The recoveries of analytes ranged from 67.5 to 111.3 %, and the RSD ranged from 0.7 to 10.9 %. The resulting correlations between the aliphatic acids and FAMEs suggest that the FAMEs had sources similar to those of the carboxylic acids, or were formed by esterifying carboxylic acids, or that aliphatic acids were formed by hydrolyzing FAMEs. Through extraction and cleanup using this procedure, 17 aromatic acids in eluate were identified and quantified by gas chromatography/tandem mass spectrometry, including five polycyclic aromatic hydrocarbon (PAH): acids 2-naphthoic, biphenyl-4-carboxylic, 9-oxo-9H-fluorene-1-carboxylic, biphenyl-4,4´-dicarboxylic, and phenanthrene-1-carboxylic acid, plus 1,8-naphthalic anhydride. Correlations between the PAH acids and the dicarboxylic and aromatic acids suggested that the first three acids and 1,8-naphthalic anhydride were secondary atmospheric photochemistry products and the last two mainly primary.

  5. Highly efficient procedure for the synthesis of fructone fragrance using a novel carbon based acid.

    PubMed

    Hu, Baowei; Li, Chunqing; Zhao, Sheng-Xian; Rong, Lin-Mei; Lv, Shao-Qin; Liang, Xuezheng; Qi, Chenze

    2010-08-01

    The novel carbon based acid has been synthesized via one-step hydrothermal carbonization of furaldehyde and hydroxyethylsulfonic acid. A highly efficient procedure for the synthesis of fructone has been developed using the novel carbon based acid. The results showed that the catalyst possessed high activity for the reaction, giving a yield of over 95%. The advantages of high activity, stability, reusability and low cost for a simple synthesis procedure and wide applicability to various diols and beta-keto esters make this novel carbon based acid one of the best choices for the reaction.

  6. Novel diketopiperazine metabolism in a microorganism: two-step hydrolysis of cyclo(Gly-Leu) to amino acids and preliminary characterization of cyclo(Gly-Leu) hydrolase and dipeptidase.

    PubMed

    Kanzaki, H; Mizuta, N; Nitoda, T; Kawazu, K

    2000-01-01

    A bacterium, strain NM 5-3, isolated from soil exhibited the highest cyclo(Gly-Leu) (CGL)-hydrolyzing activity and was identified as Agrobacterium radiobacter. The reaction products from CGL were dipeptides (Leu-Gly and Gly-Leu) and amino acids (Leu and Gly). Inhibitors for the dipeptidase of this strain did not inhibit the hydrolysis of CGL to dipeptides, indicating that two distinct enzymes, CGLase and a dipeptidase, were involved in its hydrolysis. The activities of these two enzymes were separated by anion-exchange column chromatography. The results indicated that strain NM5-3 hydrolyzed CGL via the dipeptides to the corresponding amino acids. The CGLase fraction was found to catalyze the hydrolysis of cyclo(Gly-D-Leu), cyclo(Gly-Gly), cyclo(L-Ala-Gly), and cyclo(D-Ala-Gly). On the other hand, the dipeptidase fraction exhibited L-specific substrate specificity.

  7. Simultaneous analysis of codeine, morphine, and heroin after B-glucuronidase hydrolysis.

    PubMed

    Zezulak, M; Snyder, J J; Needleman, S B

    1993-11-01

    Analysis of the opiates, morphine and codeine, often proceeds by way of acid hydrolysis for release of the parent morphine from its glucuronide formed during metabolism. Following use, heroin is rapidly deacetylated to 6-monoacetylmorphine (6-MAM), which can be detected in the urine for a short time following injection of heroin. Only a small amount of 6-MAM may be further metabolized to morphine glucuronide. Thus, in general, the urine specimen has not been hydrolyzed prior to analysis for heroin, using a separate procedure from morphine and codeine. Simultaneous analysis of morphine, codeine, 6-MAM and heroin would be complicated by loss of identity between morphine and heroin when heroin converts to morphine following acid hydrolysis for removal of the glucuronide moiety from morphine glucuronide. Another significant problem in simultaneous analysis is the relative disparity in concentration between morphine/codeine and 6-MAM/heroin (which might be present in the urine specimen). In the proposed method of analysis, free morphine resulting from B-glucuronidase rather than acid hydrolysis of morphine glucuronide is derivatized with propionic anhydride to form dipropionylmorphine. Heroin that does not react with B-glucuronidase remains unhydrolyzed as the diacetylmorphine derivative. Some of the more exacting steps for the acid procedure are eliminated altogether making overall costs for the enzyme procedure comparable to those of the acid hydrolysis method. The enzyme reaction mixture is purified through a solid phase column system. The optimal conditions for concentration of enzyme, temperature of hydrolysis and pH are individually characterized for B-glucuronidase hydrolysis and the ions which identify the propionyl derivatives are characterized for the simultaneous analysis of morphine, codeine, 6-MAM and heroin. PMID:8263474

  8. An enhanced procedure for measuring organic acids and methyl esters in PM2.5

    NASA Astrophysics Data System (ADS)

    Liu, F.; Duan, F.; He, K.; Ma, Y.; Rahn, K. A.; Zhang, Q.

    2015-03-01

    We have developed an enhanced analytical procedure to measure organic acids and methyl esters in fine aerosol with much greater specificity and sensitivity than previously available. This capability is important because of these species and their low concentrations, even in highly polluted atmospheres like Beijing, China. The procedure first separates the acids and esters from the other organic compounds with anion-exchange solid- phase extraction (SPE), then, quantifies them by gas chromatography coupled with mass spectrometry. This allows us to accurately quantify the C4-C11 dicarboxylic and the C8-C30 monocarboxylic acids. Then the acids are separated from the esters on an aminopropyl SPE cartridge, whose weak retention isolates and enriches the acids from esters prevents the fatty acids and dimethyl phthalate from being overestimated. The resulting correlations between the aliphatic acids and fatty acid methyl esters (FAMEs) suggest that FAMEs had sources similar to those of the carboxylic acids, or were formed by esterifying carboxylic acids, or that aliphatic acids were formed by hydrolyzing FAMEs. In all, 17 aromatic acids were identified and quantified using this procedure coupled with gas chromatography-tandem mass spectrometry, including the five polycyclic aromatic hydrocarbon (PAH) acids 2-naphthoic, biphenyl-4-carboxylic, 9-oxo-9H-fluorene-1-carboxylic, biphenyl-4,4´-dicarboxylic, and phenanthrene-1-carboxylic acid, plus 1,8-naphthalic anhydride. Correlations between the PAH-acids and the dicarboxylic and aromatic acids indicated that the first three acids and 1,8-naphthalic anhydride were mainly secondary, the last two mainly primary.

  9. Computer-assisted Gran titration procedure for strong acid determination

    SciTech Connect

    Phillips, M.F.; Gaffney, J.S.; Goodrich, R.W.; Tanner, R.L.

    1984-10-01

    An automated method for determining, by coulometric titration, small amounts of strong acid in the presence of weak acids is given. Essentially, a pH meter and a coulometer are coupled with a Tektronix 4052 mini-computer, and a two-step computer program then directs the titration and calculates the equivalence point by the method of Gran. A comparison of precision and accuracy of results for test solutions by manual and automated data reduction methods is presented. The method is being used successfully to analyze for the H/sup +/ content in ambient aerosol samples from aerometric field experiments, and can be used for cloud and rainwater samples as well. 3 references, 1 figure, 1 table.

  10. Phytochemical composition and effects of commercial enzymes on the hydrolysis of gallic acid glycosides in mango (Mangifera indica L. cv. 'Keitt') pulp.

    PubMed

    Krenek, Kimberly A; Barnes, Ryan C; Talcott, Stephen T

    2014-10-01

    A detailed characterization of mango pulp polyphenols and other minor phytochemicals was accomplished for the first time in the cultivar 'Keitt' whereby the identification and semiquantification of five hydroxybenzoic acids, four cinnamic acids, two flavonoids, and six apocarotenoids was accomplished. Among the most abundant compounds were two monogalloyl glucosides (MGG) identified as having an ester- or ether-linked glucose, with the ester-linked moiety present in the highest concentration among nontannin polyphenolics. Additionally, the impact of side activities of three commercial cell-wall degrading enzymes during 'Keitt' mango pulp processing was evaluated to determine their role on the hydrolysis of ester- and ether-linked phenolic acids. The use of Crystalzyme 200XL reduced the concentration of ester-linked MGG by 66%, and the use of Rapidase AR 2000 and Validase TRL completely hydrolyzed ether-linked MGG after 4 h of treatment at 50 °C. Fruit quality, in vivo absorption rate, and bioactivity of mango phytochemicals rely on their chemical characterization, and characterizing changes in composition is critical for a complete understanding of in vivo mechanisms.

  11. Nutritional value of protein hydrolysis products (oligopeptides and free amino acids) as a consequence of absorption and metabolism kinetics

    NASA Technical Reports Server (NTRS)

    Rerat, A.

    1995-01-01

    When pigs were submitted to duodenal infusion of solutions containing a large percentage of small peptides (PEP) or free amino acids with the same pattern (AAL) amino acids appear in the portal blood more rapidly and more uniformly after infusion of PEP then after infusion of AAL, with the notable exception of methionine for which the opposite was true. These differences were lowered when a carbohydrate (maltose dextrin) was present in the solution, but nevertheless remained significant for the first hour after the infusion. The long-term (8-hour) uptake of free amino acids into the liver and the peripheral tissues differed in profile according to the nature of the duodenal infusion. Peripheral uptake was appreciably less well balanced after infusion of free amino acids (deficiency of threonine and phenylalanine) than after infusion of small peptides (deficiency of methionine). Accordingly, in the rat, under conditions of discontinuous enteral nutrition the mixture of small peptides was of greater nutritive value than the mixture of free amino acids. It thus appears that the absorption kinetics which results in important variations in the temporal distribution of free amino acids in the tissues may be at the origin of transitory imbalances in tissue amino acid uptake, and as a result of a lower nutritive value.

  12. Long-term ritonavir exposure increases fatty acid and glycerol recycling in 3T3-L1 adipocytes as compensatory mechanisms for increased triacylglycerol hydrolysis.

    PubMed

    Adler-Wailes, Diane C; Guiney, Evan L; Wolins, Nathan E; Yanovski, Jack A

    2010-05-01

    Lipodystrophy with high nonesterified fatty acid (FA) efflux is reported in humans receiving highly active antiretroviral therapy (HAART) to treat HIV infection. Ritonavir, a common component of HAART, alters adipocyte FA efflux, but the mechanism for this effect is not established. To investigate ritonavir-induced changes in FA flux and recycling through acylglycerols, we exposed differentiated murine 3T3-L1 adipocytes to ritonavir for 14 d. FA efflux, uptake, and incorporation into acylglycerols were measured. To identify a mediator of FA efflux, we measured adipocyte triacylglycerol lipase (ATGL) transcript and protein. To determine whether ritonavir-treated adipocytes increased glycerol backbone synthesis for FA reesterification, we measured labeled glycerol and pyruvate incorporation into triacylglycerol (TAG). Ritonavir-treated cells had increased FA efflux, uptake, and incorporation into TAG (all P < 0.01). Ritonavir increased FA efflux without consistently increasing glycerol release or changing TAG mass, suggesting increased partial TAG hydrolysis. Ritonavir-treated adipocytes expressed significantly more ATGL mRNA (P < 0.05) and protein (P < 0.05). Ritonavir increased glycerol (P < 0.01) but not pyruvate (P = 0.41), utilization for TAG backbone synthesis. Consistent with this substrate utilization, glycerol kinase transcript (required for glycerol incorporation into TAG backbone) was up-regulated (P < 0.01), whereas phosphoenolpyruvate carboxykinase transcript (required for pyruvate utilization) was down-regulated (P < 0.001). In 3T3-L1 adipocytes, long-term ritonavir exposure perturbs FA metabolism by increasing ATGL-mediated partial TAG hydrolysis, thus increasing FA efflux, and leads to compensatory increases in FA reesterification with glycerol and acylglycerols. These changes in FA metabolism may, in part, explain the increased FA efflux observed in ritonavir-associated lipodystrophy.

  13. A process to produce penicillin G acylase by surface-adhesion fermentation using Mucor griseocyanus to obtain 6-aminopenicillanic acid by penicillin G hydrolysis.

    PubMed

    Martínez-Hernández, José Luis; Mata-Gómez, Marco Arnulfo; Aguilar-González, Cristóbal Noé; Ilyina, Anna

    2010-04-01

    The production of extracellular and mycelia-associated penicillin G acylase (maPGA) with Mucor griseocyanus H/55.1.1 by surface-adhesion fermentation using Opuntia imbricata, a cactus, as a natural immobilization support was studied. Enzyme activity to form 6-aminopencillanic acid (6-APA) from penicillin G was assayed spectrophotometrically. The penicillin G hydrolysis to 6-APA was evaluated at six different times using PGA samples recovered from the skim milk medium at five different incubation times. Additionally, the effect of varying the penicillin G substrate concentration level on the PGA enzyme activity was also studied. The maximum reaction rate, V (max), and the Michaelis constant, K (M), were determined using the Michaelis-Menten model. The maximum levels for maPGA and extracellular activity were found to be 2,126.50 international unit per liter (IU/l; equal to 997.83 IU/g of support) at 48 h and 755.33 IU/l at 60 h, respectively. Kinetics of biomass production for total biomass showed a maximum growth at 60 h of 3.36 and 2.55 g/l (equal to 0.012 g of biomass per gram of support) for the immobilized M. griseocyanus biomass. The maPGA was employed for the hydrolysis of penicillin G to obtain 6-APA in a batch reactor. The highest quantity of 6-APA obtained was 226.16 mg/l after 40-min reaction. The effect of substrate concentration on maPGA activity was evaluated at different concentrations of penicillin G (0-10 mM). K(M) and V(max) were determined to be 3.0 x 10(-3) M and 4.4 x 10(-3) mM/min, respectively.

  14. A new test procedure for biogenic sulfuric acid corrosion of concrete

    PubMed

    Vincke; Verstichel; Monteny; Verstraete

    1999-01-01

    A new test method is described for biogenic sulfuric acid corrosion of concrete, more specifically in sewer conditions. The aim of the new test method is the development of an accelerated and reproducible procedure for monitoring the resistance of different types of concrete with regard to biogenic sulfuric acid corrosion. This experimental procedure reflects worst case conditions by providing besides H2S, also an enrichment of thiobacilli and biologically produced sulfur. By simulating the cyclic processes occurring in sewer pipes, significant differences between concrete mixtures could be detected after 51 days. Concrete modified by a styrene-acrylic ester polymer demonstrated a higher resistance against biogenic sulfuric acid attack. PMID:11068828

  15. A new test procedure for biogenic sulfuric acid corrosion of concrete

    PubMed

    Vincke; Verstichel; Monteny; Verstraete

    1999-01-01

    A new test method is described for biogenic sulfuric acid corrosion of concrete, more specifically in sewer conditions. The aim of the new test method is the development of an accelerated and reproducible procedure for monitoring the resistance of different types of concrete with regard to biogenic sulfuric acid corrosion. This experimental procedure reflects worst case conditions by providing besides H2S, also an enrichment of thiobacilli and biologically produced sulfur. By simulating the cyclic processes occurring in sewer pipes, significant differences between concrete mixtures could be detected after 51 days. Concrete modified by a styrene-acrylic ester polymer demonstrated a higher resistance against biogenic sulfuric acid attack.

  16. Carbachol induces a rapid and sustained hydrolysis of polyphosphoinositide in bovine tracheal smooth muscle measurements of the mass of polyphosphoinositides, 1,2-diacylglycerol, and phosphatidic acid

    SciTech Connect

    Takuwa, Y.; Takuwa, N.; Rasmussen, H.

    1986-11-05

    The effects of carbachol on polyphosphoinositides and 1,2-diacylglycerol metabolism were investigated in bovine tracheal smooth muscle by measuring both lipid mass and the turnover of (/sup 3/H)inositol-labeled phosphoinositides. Carbachol induces a rapid reduction in the mass of phosphatidylinositol 4,5-bisphosphate and phosphatidylinositol 4-monophosphate and a rapid increase in the mass of 1,2-diacylglycerol and phosphatidic acid. These changes in lipid mass are sustained for at least 60 min. The level of phosphatidylinositol shows a delayed and progressive decrease during a 60-min period of carbachol stimulation. The addition of atropine reverses these responses completely. Carbachol stimulates a rapid loss in (/sup 3/H)inositol radioactivity from phosphatidylinositol 4,5-bisphosphate and phosphatidylinositol 4-monophosphate associated with production of (/sup 3/H)inositol trisphosphate. The carbachol-induced change in the mass of phosphoinositides and phosphatidic acid is not affected by removal of extracellular Ca/sup 2 +/ and does not appear to be secondary to an increase in intracellular Ca/sup 2 +/. These results indicate that carbachol causes phospholipase C-mediated polyphosphoinositide breakdown, resulting in the production of inositol trisphosphate and a sustained increase in the actual content of 1,2-diacylglycerol. These results strongly suggest that carbachol-induced contraction is mediated by the hydrolysis of polyphosphoinositides with the resulting generation of two messengers: inositol 1,4,5-trisphosphate and 1,2-diacylglycerol.

  17. Carbachol induces a rapid and sustained hydrolysis of polyphosphoinositide in bovine tracheal smooth muscle measurements of the mass of polyphosphoinositides, 1,2-diacylglycerol, and phosphatidic acid.

    PubMed

    Takuwa, Y; Takuwa, N; Rasmussen, H

    1986-11-01

    The effects of carbachol on polyphosphoinositides and 1,2-diacylglycerol metabolism were investigated in bovine tracheal smooth muscle by measuring both lipid mass and the turnover of [3H]inositol-labeled phosphoinositides. Carbachol induces a rapid reduction in the mass of phosphatidylinositol 4,5-bisphosphate and phosphatidylinositol 4-monophosphate and a rapid increase in the mass of 1,2-diacylglycerol and phosphatidic acid. These changes in lipid mass are sustained for at least 60 min. The level of phosphatidylinositol shows a delayed and progressive decrease during a 60-min period of carbachol stimulation. The addition of atropine reverses these responses completely. Carbachol stimulates a rapid loss in [3H]inositol radioactivity from phosphatidylinositol 4,5-bisphosphate and phosphatidylinositol 4-monophosphate associated with production of [3H]inositol trisphosphate. The carbachol-induced change in the mass of phosphoinositides and phosphatidic acid is not affected by removal of extracellular Ca2+ and does not appear to be secondary to an increase in intracellular Ca2+. These results indicate that carbachol causes phospholipase C-mediated polyphosphoinositide breakdown, resulting in the production of inositol trisphosphate and a sustained increase in the actual content of 1,2-diacylglycerol. These results strongly suggest that carbachol-induced contraction is mediated by the hydrolysis of polyphosphoinositides with the resulting generation of two messengers: inositol 1,4,5-trisphosphate and 1,2-diacylglycerol.

  18. Response surface optimization of corn stover pretreatment using dilute phosphoric acid for enzymatic hydrolysis and ethanol production

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Dilute H3PO4 (0.0 - 2.0%, v/v) was used to pretreat corn stover (10%, w/w) for conversion to ethanol. Pretreatment conditions were optimized for temperature, acid loading, and time using a central composite design. Optimal pretreatment conditions were chosen to promote sugar yields following enzym...

  19. Continuous steam hydrolysis of tulip poplar

    SciTech Connect

    Fieber, C.A.; Roberts, R.S.; Faass, G.S.; Muzzy, J.D.; Colcord, A.R.; Bery, M.K.

    1982-01-01

    The continuous hydrolysis of poplar chips by steam at 300-350 psi resulted in the separation of hemicellulose (I) cellulose and lignin components. The I fraction was readily depolymerised by steam to acetic acid, furfural, methanol, and xylose.

  20. Effect of feeding lipids recovered from fish processing waste by lactic acid fermentation and enzymatic hydrolysis on antioxidant and membrane bound enzymes in rats.

    PubMed

    Rai, Amit Kumar; Bhaskar, N; Baskaran, V

    2015-06-01

    Fish oil recovered from fresh water fish visceral waste (FVW-FO) through lactic acid fermentation (FO-LAF) and enzymatic hydrolysis (FO-EH) were fed to rats to study their influence on lipid peroxidation and activities of antioxidant and membrane bound enzyme in liver, heart and brain. Feeding of FO-LAF and FO-EH resulted in increase (P < 0.05) in lipid peroxides level in serum, liver, brain and heart tissues compared to ground nut oil (control). Activity of catalase (40-235 %) and superoxide dismutase (17-143 %) also increased (P < 0.05) with incremental level of EPA + DHA in diet. The increase was similar to cod liver oil fed rats at same concentration of EPA + DHA. FO-LAF and FO-EH increased (P < 0.05) the Na(+)K(+) ATPase activity in liver and brain microsomes, Ca(+)Mg(+) ATPase in heart microsome and acetylcholine esterase in brain microsomes when fed with 5 % EPA + DHA. There was also significant change in fatty acid composition and cholesterol/phospholipid ratio in microsomes of rat fed with FVW-FO. Feeding FVW-FO recovered by biotechnological approaches enhanced the activity of antioxidant enzymes in tissues, modulates the activities of membrane bound enzymes and improved the fatty acid composition in microsomes of tissues similar to CLO. Utilization of these processing wastes for the production of valuable biofunctional products can reduce the mounting economic values of fish oil and minimize the environmental pollution problems.

  1. Characterization of degradation products of ivabradine by LC-HR-MS/MS: a typical case of exhibition of different degradation behaviour in HCl and H2SO4 acid hydrolysis.

    PubMed

    Patel, Prinesh N; Borkar, Roshan M; Kalariya, Pradipbhai D; Gangwal, Rahul P; Sangamwar, Abhay T; Samanthula, Gananadhamu; Ragampeta, Srinivas

    2015-02-01

    A validated stability-indicating HPLC method was established, and comprehensive stress testing of ivabradine, a cardiotonic drug, was carried out as per ICH guidelines. Ivabradine was subjected to acidic, basic and neutral hydrolysis, oxidation, photolysis and thermal stress conditions, and the resulting degradation products were investigated by LC-PDA and LC-HR-MS/MS. The drug was found to degrade in acid and base hydrolysis. An efficient and selective stability assay method was developed on Phenomenex Luna C18 (250 × 4.6 mm, 5.0 µm) column using ammonium formate (10 mM, pH 3.0) and acetonitrile as mobile phase at 30 °C in gradient elution mode. The flow rate was 0.7 ml/min and detection wavelength was 286 nm. A total of five degradation products (I-1 to I-5) were identified and characterized by LC-HR-MS/MS in combination with accurate mass measurements. The drug exhibited different degradation behaviour in HCl and H2SO4 hydrolysis conditions. It is a unique example where two of the five degradation products in HCl hydrolysis were absent in H2SO4 acid hydrolysis. The present study provides guidance to revise the stress test for the determination of inherent stability of drugs containing lactam moiety under hydrolytic conditions. Most probable mechanisms for the formation of degradation products have been proposed on the basis of a comparison of the fragmentation pattern of the drug and its degradation products. In silico toxicity revealed that the degradation products (I-2 to I-5) were found to be severe irritants in case of ocular irritancy. The analytical assay method was validated with respect to specificity, linearity, range, precision, accuracy and robustness.

  2. Optimization of hydrolysis and volatile fatty acids production from sugarcane filter cake: Effects of urea supplementation and sodium hydroxide pretreatment.

    PubMed

    Janke, Leandro; Leite, Athaydes; Batista, Karla; Weinrich, Sören; Sträuber, Heike; Nikolausz, Marcell; Nelles, Michael; Stinner, Walter

    2016-01-01

    Different methods for optimization the anaerobic digestion (AD) of sugarcane filter cake (FC) with a special focus on volatile fatty acids (VFA) production were studied. Sodium hydroxide (NaOH) pretreatment at different concentrations was investigated in batch experiments and the cumulative methane yields fitted to a dual-pool two-step model to provide an initial assessment on AD. The effects of nitrogen supplementation in form of urea and NaOH pretreatment for improved VFA production were evaluated in a semi-continuously operated reactor as well. The results indicated that higher NaOH concentrations during pretreatment accelerated the AD process and increased methane production in batch experiments. Nitrogen supplementation resulted in a VFA loss due to methane formation by buffering the pH value at nearly neutral conditions (∼ 6.7). However, the alkaline pretreatment with 6g NaOH/100g FCFM improved both the COD solubilization and the VFA yield by 37%, mainly consisted by n-butyric and acetic acids.

  3. Rapid method for the simultaneous determination of flavonol aglycones in food using u-HPLC coupled with heating block acidic hydrolysis.

    PubMed

    Shim, You-Shin; Kim, Seunghee; Seo, Dongwon; Ito, Masahito; Nakagawa, Hiroaki; Park, Hyun-Jin; Ha, Jaeho

    2013-01-01

    A rapid method for the simultaneous determination of flavonol aglycones in food using ultra-high-performance LC (u-HPLC) coupled with a heating-block acidic hydrolysis method was validated in terms of precision, accuracy, and linearity. The u-HPLC separation was performed on an RP C18 column (particle size 2 micro m id, 2 mm, length 100 mm) with a photodiode array detector. The LOD and LOQ of the u-HPLC analyses were 0.15 and 0.47 mg/kg for myricetin, 0.09 and 0.28 mg/kg for quercetin, 0.16 and 0.49 mg/kg for kaempferol, and 0.08 and 0.25 mg/kg for isorhamnetin. The intraday and interday precisions of the individual flavonol aglycones were less than 9.31%. All calibration curves exhibited good linearity (r2 = 0.99) within the tested ranges. Total run time of u-HPLC was 13 min. The rapid u-HPLC method presented herein significantly improved the speed, sensitivity, and resolution of the analyses of myricetin, quercetin, kaempferol, and isorhamnetin in food.

  4. Topochemical distribution of lignin and hydroxycinnamic acids in sugar-cane cell walls and its correlation with the enzymatic hydrolysis of polysaccharides

    PubMed Central

    2011-01-01

    Background Lignin and hemicelluloses are the major components limiting enzyme infiltration into cell walls. Determination of the topochemical distribution of lignin and aromatics in sugar cane might provide important data on the recalcitrance of specific cells. We used cellular ultraviolet (UV) microspectrophotometry (UMSP) to topochemically detect lignin and hydroxycinnamic acids in individual fiber, vessel and parenchyma cell walls of untreated and chlorite-treated sugar cane. Internodes, presenting typical vascular bundles and sucrose-storing parenchyma cells, were divided into rind and pith fractions. Results Vascular bundles were more abundant in the rind, whereas parenchyma cells predominated in the pith region. UV measurements of untreated fiber cell walls gave absorbance spectra typical of grass lignin, with a band at 278 nm and a pronounced shoulder at 315 nm, assigned to the presence of hydroxycinnamic acids linked to lignin and/or to arabino-methylglucurono-xylans. The cell walls of vessels had the highest level of lignification, followed by those of fibers and parenchyma. Pith parenchyma cell walls were characterized by very low absorbance values at 278 nm; however, a distinct peak at 315 nm indicated that pith parenchyma cells are not extensively lignified, but contain significant amounts of hydroxycinnamic acids. Cellular UV image profiles scanned with an absorbance intensity maximum of 278 nm identified the pattern of lignin distribution in the individual cell walls, with the highest concentration occurring in the middle lamella and cell corners. Chlorite treatment caused a rapid removal of hydroxycinnamic acids from parenchyma cell walls, whereas the thicker fiber cell walls were delignified only after a long treatment duration (4 hours). Untreated pith samples were promptly hydrolyzed by cellulases, reaching 63% of cellulose conversion after 72 hours of hydrolysis, whereas untreated rind samples achieved only 20% hydrolyzation. Conclusion The low

  5. The formation of isocyanic acid (HNCO) by reaction of NO, CO, and H{sub 2} over Pt/SiO{sub 2} and its hydrolysis on alumina

    SciTech Connect

    Duempelmann, R.; Cant, N.W.; Trimm, D.L.

    1996-08-01

    The reaction of mixtures of NO, CO, and H{sub 2} over Pt/SiO{sub 2} in combination with Al{sub 2}O{sub 3} has been investigated with on-line Fourier transform infrared spectroscopy as the principal analytical method. With Pt/SiO{sub 2} alone isocyanic acid (HNCO) can be observed directly as a substantial product. It comprises up to 45% of the CO converted in the temperature range from 200 to 300{degrees}C. The yield is maximized when the amounts of H{sub 2} and CO in the input stream are equal. No HNCO can be observed in experiments in which Al{sub 2}O{sub 3} is placed downstream of the Pt/SiO{sub 2} or with a Pt/Al{sub 2}O{sub 3} is placed downstream of the Pt/SiO{sub 2} or with a Pt/Al{sub 2}O{sub 3} catalyst. Hydrolysis to NH{sub 3} and CO{sub 2} is then complete. For this reason it is unlikely that HNCO will escape a catalytic converter in vehicle use but it may be a significant intermediate during the warm-up phase. The formation of HNCO can be rationalized as resulting from the hydrogenation of NCO groups present in small concentrations on the Pt surface under conditions of high CO coverage. The yield of HNCO falls steeply above 300{degrees}C when the CO coverage is falling. It is unclear if hydrolysis of HNCO occurs by direct reaction of molecular HNCO on the Al{sub 2}O{sub 3} surface or proceeds via the ubiquitious support-bound isocyanate species which have been observed in many previous studies. Previous observations of isocyanate formation in hydrogen-free systems can be rationalized as arising from HNCO formation by reverse spillover of hydrogen from OH groups on the support to generate HNCO on the platinum metal. This is then transported back to the support through the gas phase to form NCO groups. 47 refs., 7 figs.

  6. Development of microwave-assisted acid hydrolysis of proteins using a commercial microwave reactor and its combination with LC-MS for protein full-sequence analysis.

    PubMed

    Chen, Lu; Wang, Nan; Li, Liang

    2014-11-01

    Microwave-assisted acid hydrolysis (MAAH) can be used to degrade a protein non-specifically into many peptides with overlapping sequences which can be identified by mass spectrometry (MS) to produce a sequence map that covers the full sequence of a protein. The success of this method for protein sequence analysis depends on the proper control of the MAAH process, which is currently done using a household microwave oven. However, to meet the regulatory or good laboratory practice (GLP) requirement in a clinical or pharmaceutical laboratory, using a commercial microwave device is often required. In this paper, we report a method of performing MAAH using a CEM Discover single-mode microwave reactor. It is shown that, using an optimized protocol for MAAH, reproducible results comparable to those obtained using a household microwave oven can be generated using the commercial reactor. To illustrate the potential applications of MAAH MS for characterizing clinically relevant proteins, this method was applied, for the first time, to map the amino acid sequences of normal and sickle-cell human hemoglobin as well as bovine hemoglobin. Full sequence coverage was readily achieved from 294 and 266 unique peptides matched to the alpha and beta subunits of normal hemoglobin, respectively, 334 and 265 unique peptides matched to the alpha and beta submit units of sickle-cell hemoglobin, and 377 and 224 unique peptides matched to the alpha and beta subunits of bovine hemoglobin. This method opens the possibility for any laboratory to use a commercial laboratory equipment to perform MAAH MS for protein full-sequence analysis. PMID:25127597

  7. Structural investigation of a uronic acid-containing polysaccharide from abalone by graded acid hydrolysis followed by PMP-HPLC-MSn and NMR analysis.

    PubMed

    Wang, Hong-xu; Zhao, Jun; Li, Dong-mei; Song, Shuang; Song, Liang; Fu, Ying-huan; Zhang, Li-peng

    2015-01-30

    A new strategy was applied to elucidate the structure of a polysaccharide from abalone gonad (AGSP). It was hydrolyzed by 0.05 M, 0.2 M, 0.5 M, and 2.0 M TFA at 100 °C for 1 h, sequentially. Every hydrolysate was ultrafiltrated (3000 Da) to collect oligo- and monosaccharides, and the final retentate was further hydrolyzed with 2.0 M TFA at 110 °C and 121 °C for 2 h, respectively. 1-Phenyl-3-methyl-5-pyrazolone (PMP) derivatization followed by HPLC-MSn analysis was applied to detect the sugar residues in these hydrolysates, which allowed proposing their location in the polysaccharide structure. The retentate after 0.5 M TFA hydrolysis was confirmed as the polysaccharide backbone, and it was further analyzed by 1D and 2D NMR spectroscopy. Thus, the structural elucidation of AGSP was accomplished, and it has a backbone of →4)-β-GlcA(1→2)-α-Man(1→ repeating unit with Fuc, Xyl and Gal in the branch. The analytical strategy demonstrated was useful to characterize the structure of polysaccharides.

  8. Structural investigation of a uronic acid-containing polysaccharide from abalone by graded acid hydrolysis followed by PMP-HPLC-MSn and NMR analysis.

    PubMed

    Wang, Hong-xu; Zhao, Jun; Li, Dong-mei; Song, Shuang; Song, Liang; Fu, Ying-huan; Zhang, Li-peng

    2015-01-30

    A new strategy was applied to elucidate the structure of a polysaccharide from abalone gonad (AGSP). It was hydrolyzed by 0.05 M, 0.2 M, 0.5 M, and 2.0 M TFA at 100 °C for 1 h, sequentially. Every hydrolysate was ultrafiltrated (3000 Da) to collect oligo- and monosaccharides, and the final retentate was further hydrolyzed with 2.0 M TFA at 110 °C and 121 °C for 2 h, respectively. 1-Phenyl-3-methyl-5-pyrazolone (PMP) derivatization followed by HPLC-MSn analysis was applied to detect the sugar residues in these hydrolysates, which allowed proposing their location in the polysaccharide structure. The retentate after 0.5 M TFA hydrolysis was confirmed as the polysaccharide backbone, and it was further analyzed by 1D and 2D NMR spectroscopy. Thus, the structural elucidation of AGSP was accomplished, and it has a backbone of →4)-β-GlcA(1→2)-α-Man(1→ repeating unit with Fuc, Xyl and Gal in the branch. The analytical strategy demonstrated was useful to characterize the structure of polysaccharides. PMID:25497339

  9. Evaluation of Acid Digestion Procedures to Estimate Mineral Contents in Materials from Animal Trials

    PubMed Central

    Palma, M. N. N.; Rocha, G. C.; Valadares Filho, S. C.; Detmann, E.

    2015-01-01

    Rigorously standardized laboratory protocols are essential for meaningful comparison of data from multiple sites. Considering that interactions of minerals with organic matrices may vary depending on the material nature, there could be peculiar demands for each material with respect to digestion procedure. Acid digestion procedures were evaluated using different nitric to perchloric acid ratios and one- or two-step digestion to estimate the concentration of calcium, phosphorus, magnesium, and zinc in samples of carcass, bone, excreta, concentrate, forage, and feces. Six procedures were evaluated: ratio of nitric to perchloric acid at 2:1, 3:1, and 4:1 v/v in a one- or two-step digestion. There were no direct or interaction effects (p>0.01) of nitric to perchloric acid ratio or number of digestion steps on magnesium and zinc contents. Calcium and phosphorus contents presented a significant (p<0.01) interaction between sample type and nitric to perchloric acid ratio. Digestion solution of 2:1 v/v provided greater (p<0.01) recovery of calcium and phosphorus from bone samples than 3:1 and 4:1 v/v ratio. Different acid ratios did not affect (p>0.01) calcium or phosphorus contents in carcass, excreta, concentrate, forage, and feces. Number of digestion steps did not affect mineral content (p>0.01). Estimated concentration of calcium, phosphorus, magnesium, and zinc in carcass, excreta, concentrated, forage, and feces samples can be performed using digestion solution of nitric to perchloric acid 4:1 v/v in a one-step digestion. However, samples of bones demand a stronger digestion solution to analyze the mineral contents, which is represented by an increased proportion of perchloric acid, being recommended a digestion solution of nitric to perchloric acid 2:1 v/v in a one-step digestion. PMID:26333671

  10. Procedure for the quantitative determination of mixtures of nucleic Acid components based on multivariate spectrophotometric Acid-base titrations.

    PubMed

    Saurina, J; Hernández-Cassou, S; Tauler, R; Izquierdo-Ridorsa, A

    1999-01-01

    A new procedure for the quantitative determination of mixtures of nucleic acid components, based on continuous spectrophotometric acid-base titrations and multivariate curve resolution, is proposed. The procedure simultaneously takes into account the spectroscopic and acid-base properties of the compounds, which leads to a higher selectivity. Furthermore, quantitative determination of an analyte in a complex mixture is performed using a synthetic solution as standard containing only the analyte of interest. An intrinsic difficulty in the analysis of spectrometric titration data is the presence of rank deficiency due to closure for the mixtures of two or more compounds. An additional problem can be encountered in some mixtures if species spectra or species concentration profiles are practically identical (rank overlap). However, even in the presence of these rank difficulties, accurate quantitation with prediction errors lower than 5% was obtained. The presence of unknown and uncalibrated interferences in the samples does not affect the quantitative determination of the analyte of interest. The proposed procedure was successfully applied to the analysis of real samples (pharmaceuticals) using synthetic external standards.

  11. Comparative Study of Corn Stover Pretreated by Dilute Acid and Cellulose Solvent-Based Lignocellulose Fractionation: Enzymatic Hydrolysis, Supramolecular Structure, and Substrate Accessibility

    SciTech Connect

    Zhu, Z.; Sathitsuksanoh, N.; Vinzant, T.; Schell, D. J.; McMillian, J. D.; Zhang, Y. H. P.

    2009-07-01

    Liberation of fermentable sugars from recalcitrant biomass is among the most costly steps for emerging cellulosic ethanol production. Here we compared two pretreatment methods (dilute acid, DA, and cellulose solvent and organic solvent lignocellulose fractionation, COSLIF) for corn stover. At a high cellulase loading [15 filter paper units (FPUs) or 12.3 mg cellulase per gram of glucan], glucan digestibilities of the corn stover pretreated by DA and COSLIF were 84% at hour 72 and 97% at hour 24, respectively. At a low cellulase loading (5 FPUs per gram of glucan), digestibility remained as high as 93% at hour 24 for the COSLIF-pretreated corn stover but reached only {approx}60% for the DA-pretreated biomass. Quantitative determinations of total substrate accessibility to cellulase (TSAC), cellulose accessibility to cellulase (CAC), and non-cellulose accessibility to cellulase (NCAC) based on adsorption of a non-hydrolytic recombinant protein TGC were measured for the first time. The COSLIF-pretreated corn stover had a CAC of 11.57 m{sup 2}/g, nearly twice that of the DA-pretreated biomass (5.89 m{sup 2}/g). These results, along with scanning electron microscopy images showing dramatic structural differences between the DA- and COSLIF-pretreated samples, suggest that COSLIF treatment disrupts microfibrillar structures within biomass while DA treatment mainly removes hemicellulose. Under the tested conditions COSLIF treatment breaks down lignocellulose structure more extensively than DA treatment, producing a more enzymatically reactive material with a higher CAC accompanied by faster hydrolysis rates and higher enzymatic digestibility.

  12. Comparative study of corn stover pretreated by dilute acid and cellulose solvent-based lignocellulose fractionation: Enzymatic hydrolysis, supramolecular structure, and substrate accessibility.

    PubMed

    Zhu, Zhiguang; Sathitsuksanoh, Noppadon; Vinzant, Todd; Schell, Daniel J; McMillan, James D; Zhang, Y-H Percival

    2009-07-01

    Liberation of fermentable sugars from recalcitrant biomass is among the most costly steps for emerging cellulosic ethanol production. Here we compared two pretreatment methods (dilute acid, DA, and cellulose solvent and organic solvent lignocellulose fractionation, COSLIF) for corn stover. At a high cellulase loading [15 filter paper units (FPUs) or 12.3 mg cellulase per gram of glucan], glucan digestibilities of the corn stover pretreated by DA and COSLIF were 84% at hour 72 and 97% at hour 24, respectively. At a low cellulase loading (5 FPUs per gram of glucan), digestibility remained as high as 93% at hour 24 for the COSLIF-pretreated corn stover but reached only approximately 60% for the DA-pretreated biomass. Quantitative determinations of total substrate accessibility to cellulase (TSAC), cellulose accessibility to cellulase (CAC), and non-cellulose accessibility to cellulase (NCAC) based on adsorption of a non-hydrolytic recombinant protein TGC were measured for the first time. The COSLIF-pretreated corn stover had a CAC of 11.57 m(2)/g, nearly twice that of the DA-pretreated biomass (5.89 m(2)/g). These results, along with scanning electron microscopy images showing dramatic structural differences between the DA- and COSLIF-pretreated samples, suggest that COSLIF treatment disrupts microfibrillar structures within biomass while DA treatment mainly removes hemicellulose. Under the tested conditions COSLIF treatment breaks down lignocellulose structure more extensively than DA treatment, producing a more enzymatically reactive material with a higher CAC accompanied by faster hydrolysis rates and higher enzymatic digestibility.

  13. Hydrolysis of milk triglycerides by human gastric lipase.

    PubMed

    Jaśkiewicz, J; Szafran, Z; Popiela, T; Szafran, H

    1980-01-01

    The concentrations of myristic, palmitic, palmitoleic, stearic and oleic acids were determined in the products of hydrolysis of lipids of cow milk incubated with human gastric juice using thin-layer chromatography for the separation of lipid fractions, and gas liquid chromatography for the determination of fatty acids. It was found that the percentage ratio of the above fatty acids in hydrolysis products was similar to that in milk triglycerides. It was concluded that triglycerides containing higher fatty acids present in milk are hydrolysed by the lipase appearing in human gastric juice, the rate of hydrolysis of the individual acids being roughly proportional to the concentration of these acids in triglyceride substrate.

  14. General analytical procedure for determination of acidity parameters of weak acids and bases.

    PubMed

    Pilarski, Bogusław; Kaliszan, Roman; Wyrzykowski, Dariusz; Młodzianowski, Janusz; Balińska, Agata

    2015-01-01

    The paper presents a new convenient, inexpensive, and reagent-saving general methodology for the determination of pK a values for components of the mixture of diverse chemical classes weak organic acids and bases in water solution, without the need to separate individual analytes. The data obtained from simple pH-metric microtitrations are numerically processed into reliable pK a values for each component of the mixture. Excellent agreement has been obtained between the determined pK a values and the reference literature data for compounds studied.

  15. Enzymatic degradation of polygalacturonic acid by Yersinia and Klebsiella species in relation to clinical laboratory procedures.

    PubMed

    Starr, M P; Chatterjee, A K; Starr, P B; Buchanan, G E

    1977-10-01

    As scored by several specified plating procedures, clinical and environmental strains of Yersinia enterocolitica, Yersinia pseudotuberculosis, and Klebsiella pneumoniae "Oxytocum" showed detectable, albeit generally weak, ability to digest polygalacturonic (pectic) acid. None of these bacterial strains had the vigorous and rapid pectolytic activity on these polygalacturonic acid-containing media that is typical of soft-rot Erwinia species, although some of the Oxytocum strains came fairly close. Analyses of the pectolytic enzyme contents of the cells and culture supernatants of the Yersinia and Klebsiella species revealed that readily detectable quantities of cell-bound polygalacturonic acid trans-eliminase and hydrolytic polygalacturonase were formed by the Yersinia and Klebsiella species; however, the total units of enzyme activity produced by these bacteria were, in general, lower than were produced by soft-rot Erwinia species. Furthermore, unlike the situation in soft-rot Erwinia cultures, these pectolytic enzymes of Yersinia and Klebsiella species were not excreted rapidly and massively into the growth medium. Cultures of other enterobacteria (Citrobacter species, Enterobacter species, Erwinia amylovora, Erwinia herbicola, Escherichia coli, Proteus species, Salmonella typhimurium, and Serratia marcescens) showed no pectolytic ability whatsoever by any of the plating procedures used and (to the extent they were so examined) produced no pectolytic enzymes detectable either in their cells or culture supernatants. This slow or weak release of pectolytic enzymes by Yersinia and Klebsiella species has a bearing on clinical laboratory procedures suitable for detecting their pectolytic activity; methods adequate for this purpose are detailed.

  16. Enzymatic Degradation of Polygalacturonic Acid by Yersinia and Klebsiella Species in Relation to Clinical Laboratory Procedures

    PubMed Central

    Starr, Mortimer P.; Chatterjee, Arun K.; Starr, Phoebe B.; Buchanan, Gordon E.

    1977-01-01

    As scored by several specified plating procedures, clinical and environmental strains of Yersinia enterocolitica, Yersinia pseudotuberculosis, and Klebsiella pneumoniae “Oxytocum” showed detectable, albeit generally weak, ability to digest polygalacturonic (pectic) acid. None of these bacterial strains had the vigorous and rapid pectolytic activity on these polygalacturonic acid-containing media that is typical of soft-rot Erwinia species, although some of the Oxytocum strains came fairly close. Analyses of the pectolytic enzyme contents of the cells and culture supernatants of the Yersinia and Klebsiella species revealed that readily detectable quantities of cell-bound polygalacturonic acid trans-eliminase and hydrolytic polygalacturonase were formed by the Yersinia and Klebsiella species; however, the total units of enzyme activity produced by these bacteria were, in general, lower than were produced by soft-rot Erwinia species. Furthermore, unlike the situation in soft-rot Erwinia cultures, these pectolytic enzymes of Yersinia and Klebsiella species were not excreted rapidly and massively into the growth medium. Cultures of other enterobacteria (Citrobacter species, Enterobacter species, Erwinia amylovora, Erwinia herbicola, Escherichia coli, Proteus species, Salmonella typhimurium, and Serratia marcescens) showed no pectolytic ability whatsoever by any of the plating procedures used and (to the extent they were so examined) produced no pectolytic enzymes detectable either in their cells or culture supernatants. This slow or weak release of pectolytic enzymes by Yersinia and Klebsiella species has a bearing on clinical laboratory procedures suitable for detecting their pectolytic activity; methods adequate for this purpose are detailed. PMID:334794

  17. Lactic acid and thermal treatments trigger the hydrolysis of myo-inositol hexakisphosphate and modify the abundance of lower myo-inositol phosphates in barley (Hordeum vulgare L.).

    PubMed

    Metzler-Zebeli, Barbara U; Deckardt, Kathrin; Schollenberger, Margit; Rodehutscord, Markus; Zebeli, Qendrim

    2014-01-01

    Barley is an important source of dietary minerals, but it also contains myo-inositol hexakisphosphate (InsP6) that lowers their absorption. This study evaluated the effects of increasing concentrations (0.5, 1, and 5%, vol/vol) of lactic acid (LA), without or with an additional thermal treatment at 55°C (LA-H), on InsP6 hydrolysis, formation of lower phosphorylated myo-inositol phosphates, and changes in chemical composition of barley grain. Increasing LA concentrations and thermal treatment linearly reduced (P<0.001) InsP6-phosphate (InsP6-P) by 0.5 to 1 g compared to the native barley. In particular, treating barley with 5% LA-H was the most efficient treatment to reduce the concentrations of InsP6-P, and stimulate the formation of lower phosphorylated myo-inositol phosphates such as myo-inositol tetraphosphate (InsP4) and myo-inositol pentaphosphates (InsP5). Also, LA and thermal treatment changed the abundance of InsP4 and InsP5 isomers with Ins(1,2,5,6)P4 and Ins(1,2,3,4,5)P5 as the dominating isomers with 5% LA, 1% LA-H and 5% LA-H treatment of barley, resembling to profiles found when microbial 6-phytase is applied. Treating barley with LA at room temperature (22°C) increased the concentration of resistant starch and dietary fiber but lowered those of total starch and crude ash. Interestingly, total phosphorus (P) was only reduced (P<0.05) in barley treated with LA-H but not after processing of barley with LA at room temperature. In conclusion, LA and LA-H treatment may be effective processing techniques to reduce InsP6 in cereals used in animal feeding with the highest degradation of InsP6 at 5% LA-H. Further in vivo studies are warranted to determine the actual intestinal P availability and to assess the impact of changes in nutrient composition of LA treated barley on animal performance.

  18. Lactic Acid and Thermal Treatments Trigger the Hydrolysis of Myo-Inositol Hexakisphosphate and Modify the Abundance of Lower Myo-Inositol Phosphates in Barley (Hordeum vulgare L.)

    PubMed Central

    Metzler-Zebeli, Barbara U.; Deckardt, Kathrin; Schollenberger, Margit; Rodehutscord, Markus; Zebeli, Qendrim

    2014-01-01

    Barley is an important source of dietary minerals, but it also contains myo-inositol hexakisphosphate (InsP6) that lowers their absorption. This study evaluated the effects of increasing concentrations (0.5, 1, and 5%, vol/vol) of lactic acid (LA), without or with an additional thermal treatment at 55°C (LA-H), on InsP6 hydrolysis, formation of lower phosphorylated myo-inositol phosphates, and changes in chemical composition of barley grain. Increasing LA concentrations and thermal treatment linearly reduced (P<0.001) InsP6-phosphate (InsP6-P) by 0.5 to 1 g compared to the native barley. In particular, treating barley with 5% LA-H was the most efficient treatment to reduce the concentrations of InsP6-P, and stimulate the formation of lower phosphorylated myo-inositol phosphates such as myo-inositol tetraphosphate (InsP4) and myo-inositol pentaphosphates (InsP5). Also, LA and thermal treatment changed the abundance of InsP4 and InsP5 isomers with Ins(1,2,5,6)P4 and Ins(1,2,3,4,5)P5 as the dominating isomers with 5% LA, 1% LA-H and 5% LA-H treatment of barley, resembling to profiles found when microbial 6-phytase is applied. Treating barley with LA at room temperature (22°C) increased the concentration of resistant starch and dietary fiber but lowered those of total starch and crude ash. Interestingly, total phosphorus (P) was only reduced (P<0.05) in barley treated with LA-H but not after processing of barley with LA at room temperature. In conclusion, LA and LA-H treatment may be effective processing techniques to reduce InsP6 in cereals used in animal feeding with the highest degradation of InsP6 at 5% LA-H. Further in vivo studies are warranted to determine the actual intestinal P availability and to assess the impact of changes in nutrient composition of LA treated barley on animal performance. PMID:24967651

  19. Pretreatment of dried distillers grains with solubles by soaking in aqueous ammonia and subsequent enzymatic/dilute acid hydrolysis to produce fermentable sugars

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Dried distillers grains with solubles (DDGS), a co-product of corn ethanol production in the dry-grind process, was pretreated by soaking in aqueous ammonia (SAA) using a 15% w/w NH4OH solution at a solid:liquid ratio of 1:10. The effect of pretreatment on subsequent enzymatic hydrolysis was studied...

  20. Practical preparation procedures for docetaxel-loaded nanoparticles using polylactic acid-co-glycolic acid

    PubMed Central

    Keum, Chang-Gu; Noh, Young-Wook; Baek, Jong-Suep; Lim, Ji-Ho; Hwang, Chan-Ju; Na, Young-Guk; Shin, Sang-Chul; Cho, Cheong-Weon

    2011-01-01

    Background Nanoparticles fabricated from the biodegradable and biocompatible polymer, polylactic-co-glycolic acid (PLGA), are the most intensively investigated polymers for drug delivery systems. The objective of this study was to explore fully the development of a PLGA nanoparticle drug delivery system for alternative preparation of a commercial formulation. In our nanoparticle fabrication, our purpose was to compare various preparation parameters. Methods Docetaxel-loaded PLGA nanoparticles were prepared by a single emulsion technique and solvent evaporation. The nanoparticles were characterized by various techniques, including scanning electron microscopy for surface morphology, dynamic light scattering for size and zeta potential, x-ray photoelectron spectroscopy for surface chemistry, and high-performance liquid chromatography for in vitro drug release kinetics. To obtain a smaller particle, 0.2% polyvinyl alcohol, 0.03% D-α-tocopheryl polyethylene glycol 1000 succinate (TPGS), 2% Poloxamer 188, a five-minute sonication time, 130 W sonication power, evaporation with magnetic stirring, and centrifugation at 8000 rpm were selected. To increase encapsulation efficiency in the nanoparticles, certain factors were varied, ie, 2–5 minutes of sonication time, 70–130 W sonication power, and 5–25 mg drug loading. Results A five-minute sonication time, 130 W sonication power, and a 10 mg drug loading amount were selected. Under these conditions, the nanoparticles reached over 90% encapsulation efficiency. Release kinetics showed that 20.83%, 40.07%, and 51.5% of the docetaxel was released in 28 days from nanoparticles containing Poloxamer 188, TPGS, or polyvinyl alcohol, respectively. TPGS and Poloxamer 188 had slower release kinetics than polyvinyl alcohol. It was predicted that there was residual drug remaining on the surface from x-ray photoelectron spectroscopy. Conclusion Our research shows that the choice of surfactant is important for controlled release of

  1. Novel double prodrugs of the iron chelator N,N'-bis(2-hydroxybenzyl)ethylenediamine-N,N'-diacetic acid (HBED): Synthesis, characterization, and investigation of activation by chemical hydrolysis and oxidation.

    PubMed

    Thiele, Nikki A; Abboud, Khalil A; Sloan, Kenneth B

    2016-08-01

    The development of iron chelators suitable for the chronic treatment of diseases where iron accumulation and subsequent oxidative stress are implicated in disease pathogenesis is an active area of research. The clinical use of the strong chelator N,N'-bis(2-hydroxybenzyl)ethylenediamine-N,N'-diacetic acid (HBED) and its alkyl ester prodrugs has been hindered by poor oral bioavailability and lack of conversion to the parent chelator, respectively. Here, we present novel double prodrugs of HBED that have the carboxylate and phenolate donors of HBED masked with carboxylate esters and boronic acids/esters, respectively. These double prodrugs were successfully synthesized as free bases (7a-f) or as dimesylate salts (8a-c,e), and were characterized by (1)H, (13)C, and (11)B NMR; MP; MS; and elemental analysis. The crystal structure of 8a was solved. Three of the double prodrugs (8a-c) were selected for further investigation into their abilities to convert to HBED by stepwise hydrolysis and H2O2 oxidation. The serial hydrolysis of the pinacol and methyl esters of N,N'-bis(2-boronic acid pinacol ester benzyl)ethylenediamine-N,N'-diacetic acid methyl ester dimesylate (8a) was verified by LC-MS. The macro half-lives for the hydrolyses of 8a-c, measured by UV, ranged from 3.8 to 26.3 h at 37 °C in pH 7.5 phosphate buffer containing 50% MeOH. 9, the product of hydrolysis of 8a-c and the intermediate in the conversion pathway, showed little-to-no affinity for iron or copper in UV competition experiments. 9 underwent a serial oxidative deboronation by H2O2 in N-methylmorpholine buffer to generate HBED (k = 10.3 M(-1) min(-1)). The requirement of this second step, oxidation, before conversion to the active chelator is complete may confer site specificity when only localized iron chelation is needed. Overall, these results provide proof of principle for the activation of the double prodrugs by chemical hydrolysis and H2O2 oxidation, and merit further investigation into the

  2. Hydrolysis of iodine: equilibria at high temperatures

    SciTech Connect

    Palmer, D.A.; Ramette, R.W.; Mesmer, R.E.

    1984-01-01

    The hydrolysis (or disproportionation) of molecular iodine to form iodate and iodide ions has been studied by emf measurements over the temperature range, 3.8/sup 0/ to 209.0/sup 0/C. The interpretation of these results required a knowledge of the formation constant for triiodide ion and the acid dissociation constant of iodic acid, both of which were measured as a function of temperature. The resulting thermodynamic data have been incorporated into a general computer model describing the hydrolysis equilibria of iodine as a function of initial concentration, pH and temperature.

  3. Weak-acid sites catalyze the hydrolysis of crystalline cellulose to glucose in water: importance of post-synthetic functionalization of the carbon surface.

    PubMed

    To, Anh The; Chung, Po-Wen; Katz, Alexander

    2015-09-14

    The direct hydrolysis of crystalline cellulose to glucose in water without prior pretreatment enables the transformation of biomass into fuels and chemicals. To understand which features of a solid catalyst are most important for this transformation, the nanoporous carbon material MSC-30 was post-synthetically functionalized by oxidation. The most active catalyst depolymerized crystalline cellulose without prior pretreatment in water, providing glucose in an unprecedented 70 % yield. In comparison, virtually no reaction was observed with MSC-30, even when the reaction was conducted in aqueous solution at pH 2. As no direct correlations between the activity of this solid-solid reaction and internal-site characteristics, such as the β-glu adsorption capacity and the rate of catalytic hydrolysis of adsorbed β-glu strands, were observed, contacts of the external surface with the cellulose crystal are thought to be key for the overall efficiency.

  4. Fundamental study of the mechanism and kinetics of cellulose hydrolysis by acids and enzymes. Final report, June 1, 1978-January 31, 1981

    SciTech Connect

    Gong, C.S.; Chang, M.

    1981-02-01

    There are three basic enzymes (e.g., endoglucanase (C/sub x/), exoglucanase (C/sub 1/) and cellobiase) comprising the majority of extracellular cellulase enzymes produced by the cellulolytic mycelial fungi, Trichoderma reesei, and other cellulolytic microorganisms. The enzymes exhibited different mode of actions in respect to the hydrolysis of cellulose and cellulose derived oligosaccharides. In combination, these enzymes complimented each other to hydrolyze cellulose to its basic constituent, glucose. The kinetics of cellobiase were developed on the basis of applying the pseudo-steady state assumption to hydrolyze cellobiose to glucose. The results indicated that cellobiase was subjected to end-product inhibition by glucose. The kinetic modeling of exoglucanase (C/sub 1/) with respect to cellodextrins was studied. Both glucose and cellobiose were found to be inhibitors of this enzyme with cellobiose being a stronger inhibitor than glucose. Similarly, endoglucanase (C/sub x/) is subject to end-product inhibition by glucose. Crystallinity of the cellulose affects the rate of hydrolysis by cellulases. Hence, the changes in crystallinity of cellulose in relation to chemical pretreatment and enzyme hydrolysis was compared. The study of cellulase biosynthesis resulted in the conclusion that exo- and endo-glucanases are co-induced while cellobiase is synthesized independent of the other two enzymes. The multiplicity of cellulase enzymes are the end results of post-translational modification during and/or after the secretion of enzymes into growth environment.

  5. Occurrence and human exposure of p-hydroxybenzoic acid esters (parabens), bisphenol A diglycidyl ether (BADGE), and their hydrolysis products in indoor dust from the United States and three East Asian countries.

    PubMed

    Wang, Lei; Liao, Chunyang; Liu, Fang; Wu, Qian; Guo, Ying; Moon, Hyo-Bang; Nakata, Haruhiko; Kannan, Kurunthachalam

    2012-11-01

    p-Hydroxybenzoic acid esters (parabens) and bisphenol A diglycidyl ether (BADGE) are widely present in personal care products, food packages, and material coatings. Nevertheless, little is known about the occurrence of these compounds in indoor dust. In this study, we collected 158 indoor dust samples from the U.S., China, Korea, and Japan and determined the concentrations of 11 target chemicals, viz., six parabens and their common hydrolysis product, 4-hydroxybenzoic acid (4-HB), as well as BADGE and its three hydrolysis products (BADGE·H(2)O, BADGE·2H(2)O, and BADGE·HCl·H(2)O). All of the target compounds were found in dust samples from four countries. Concentrations of sum of six parabens in dust were on the order of several hundred to several thousands of nanogram per gram. Geometric mean concentrations of BADGEs in dust ranged from 1300 to 2890 ng/g among four countries. Methyl paraben (MeP), propyl paraben (PrP), BADGE·2H(2)O, and BADGE·HCl·H(2)O were the predominant compounds found in dust samples. This is the first report of BADGE and its hydrolysis products (BADGEs) in indoor dust samples and of parabens in indoor dust from Asian countries. On the basis of the measured concentrations of target chemicals, we estimated the daily intake (EDI) via dust ingestion. The EDIs of parabens via dust ingestion were 5-10 times higher in children than in adults. Among the four countries studied, the EDIs of parabens (5.4 ng/kg-bw/day) and BADGEs (6.5 ng/kg-bw/day) through dust ingestion were the highest for children in Korea and Japan.

  6. Biological pretreatment of corn stover with ligninolytic enzyme for high efficient enzymatic hydrolysis.

    PubMed

    Wang, Feng-Qin; Xie, Hui; Chen, Wei; Wang, En-Tao; Du, Feng-Guang; Song, An-Dong

    2013-09-01

    Aiming at increasing the efficiency of transferring corn stover into sugars, a biological pretreatment was developed and investigated in this study. The protocol was characterized by the pretreatment with crude ligninolytic enzymes from Phanerochete chrysosporium and Coridus versicolor to break the lignin structure in corn stover, followed by a washing procedure to eliminate the inhibition of ligninolytic enzyme on cellulase. By a 2 d-pretreatment, sugar yield from corn stover hydrolysis could be increased by 50.2% (up to 323 mg/g) compared with that of the control. X-ray diffractometry and FT-IR analysis revealed that biological pretreatment could partially remove the lignin of corn stover, and consequently enhance the enzymatic hydrolysis efficiency of cellulose and hemeicellulose. In addition, the amount of microbial inhibitors, such as acetic acid and furfural, were much lower in biological pretreatment than that in acid pretreatment. This study provided a promising pretreatment method for biotransformation of corn stovers.

  7. Determination of 2-[N-[(S)-1-ethoxycarbonyl-3-phenylpropyl]-L-alanyl]-(1S,3S,5S)-2- azabicyclo[3.3.0]octane-3-carboxylic acid (Hoe 498) and its hydrolysis product in serum and urine.

    PubMed

    Hajdú, P; Schmidt, D; Bomm, M; Hack, L; Keller, A

    1984-01-01

    A highly sensitive and specific enzymatic assay for the quantitative determination of 2-[N-[(S)-1-ethoxycarbonyl-3-phenylpropyl]-L-alanyl]-(1S,3S, 5S)-2-azabicyclo[3.3.0]octane-3-carboxylic acid (Hoe 498) and its hydrolysis product Hoe 498-diacid in serum and a GLC method for the simultaneous determination of both compounds in urine are described. Both methods involve extraction from the respective biological fluid using disposable C 18 columns. In serum, the enzyme-inhibiting properties of Hoe 498-diacid (Hoe 498 can readily be converted to its hydrolysis product) are utilized for the determination of both compounds concurrently. The serum extract is dissolved in buffer solution and incubated with human serum as angiotensin converting enzyme (peptidyl-dipeptide-hydrolase, EC 3.4.15.1) source and hip-his-leu substrate. The hippuric acid liberated is quantitated by HPLC. The urine extract is treated with diazomethane followed by trifluoroacetic anhydride to convert Hoe 498 and Hoe 498-diacid to their methylester, trifluoroacetyl derivatives, which are then determined simultaneously by GLC using a nitrogen specific detector.

  8. [3H]Indole-3-acetyl-myo-inositol hydrolysis by extracts of Zea mays L. vegetative tissue

    NASA Technical Reports Server (NTRS)

    Hall, P. J.; Bandurski, R. S.

    1986-01-01

    [3H]Indole-3-acetyl-myo-inositol was hydrolyzed by buffered extracts of acetone powders prepared from 4 day shoots of dark grown Zea mays L. seedlings. The hydrolytic activity was proportional to the amount of extract added and was linear for up to 6 hours at 37 degrees C. Boiled or alcohol denatured extracts were inactive. Analysis of reaction mixtures by high performance liquid chromatography demonstrated that not all isomers of indole-3-acetyl-myo-inositol were hydrolyzed at the same rate. Buffered extracts of acetone powders were prepared from coleoptiles and mesocotyls. The rates of hydrolysis observed with coleoptile extracts were greater than those observed with mesocotyl extracts. Active extracts also catalyzed the hydrolysis of esterase substrates such as alpha-naphthyl acetate and the methyl esters of indoleacetic acid and naphthyleneacetic acid. Attempts to purify the indole-3-acetyl-myo-inositol hydrolyzing activity by chromatographic procedures resulted in only slight purification with large losses of activity. Chromatography over hydroxylapatite allowed separation of two enzymically active fractions, one of which catalyzed the hydrolysis of both indole-3-acetyl-myo-inositol and esterase substrates. With the other enzymic hydrolysis of esterase substrates was readily demonstrated, but no hydrolysis of indole-3-acetyl-myo-inositol was ever detected.

  9. Influence of the derivatization procedure on the results of the gaschromatographic fatty acid analysis of human milk and infant formulae.

    PubMed

    Kohn, G; van der Ploeg, P; Möbius, M; Sawatzki, G

    1996-09-01

    Many different analytical procedures for fatty acid analysis of infant formulae and human milk are described. The objective was to study possible pitfalls in the use of different acid-catalyzed procedures compared to a base-catalyzed procedure based on sodium-methoxide in methanol. The influence of the different methods on the relative fatty acid composition (wt% of total fatty acids) and the total fatty acid recovery rate (expressed as % of total lipids) was studied in two experimental LCP-containing formulae and a human milk sample. MeOH/HCl-procedures were found to result in an incomplete transesterification of triglycerides, if an additional nonpolar solvent like toluene or hexane is not added and a water-free preparation is not guaranteed. In infant formulae the low transesterification of triglycerides (up to only 37%) could result in an 100%-overestimation of the relative amount of LCP, if these fatty acids primarily derive from phospholipids. This is the case in infant formulae containing egg lipids as raw materials. In formula containing fish oils and in human milk the efficacy of esterification results in incorrect absolute amounts of fatty acids, but has no remarkable effect on the relative fatty acid distribution. This is due to the fact that in these samples LCP are primarily bound to triglycerides. Furthermore, in formulae based on butterfat the derivatization procedure should be designed in such a way that losses of short-chain fatty acids due to evaporation steps can be avoided. The procedure based on sodium methoxide was found to result in a satisfactory (about 90%) conversion of formula lipids and a reliable content of all individual fatty acids. Due to a possibly high amount of free fatty acids in human milk, which are not methylated by sodium-methoxide, caution is expressed about the use of this reagent for fatty acid analysis of mothers milk. It is concluded that accurate fatty acid analysis of infant formulae and human milk requires a careful

  10. Intramolecular general acid catalysis of the hydrolysis of 2-(2'-imidazolium)phenyl phosphate, and bond length-reactivity correlations for reactions of phosphate monoester monoanions.

    PubMed

    Brandão, Tiago A S; Orth, Elisa S; Rocha, Willian R; Bortoluzzi, Adailton J; Bunton, Clifford A; Nome, Faruk

    2007-05-11

    Rate constants for the hydrolysis of 2-(2'-imidazolium)phenyl hydrogen phosphate (IMPP) in water at pH<6 indicate that activation by the imidazolium moiety disappears with the deprotonation of the phosphate group, and the reaction involves the hydrogen-bonding of the imidazolium NH with the aryl oxygen leaving group. The reaction should involve a near-planar conformation of the imidazolium and the phenyl groups in the activated complex, which favors proton-transfer. The crystal structure of IMPP was solved, and a bond length-reactivity correlation for reactions of phosphate monoester monoanions is described.

  11. [The preparation procedure of tests for the gas chromatographic determination of fat acids without preliminary extraction of lipids].

    PubMed

    Aripovskiĭ, A V; Kolesnik, P O; Vezhdel, M I; Titov, V N

    2012-01-01

    The enhancement of the procedure of quantitative gas chromatographic determination of fit acids in biologic liquids samples is proposed. Instead of the conventional Folch procedure of extraction of lipids with subsequent ablution, concentration and methylation of extracts the direct saponification and methylation of vacuum dried liquid samples (50-200 mkl) can be applied. To compare the effectiveness of the proposed and conventional procedures both of them had been applied to evaluate how converge the results of determination of composition of fat acids in whole blood, blood plasma, packed red blood cells, homogenates of hepatic and muscular tissues. The proposed procedure is applied to determine the characteristics of fat acids composition inpatients with ischemic heart disease.

  12. Comparison of four digestion procedures not requiring perchloric acid for the trace-element analysis of plant material

    SciTech Connect

    Knight, M. J.

    1980-05-01

    Perchloric acid (HClO/sub 4/) is often used to destroy organic material contained in plant tissue during sample preparation for trace-element analysis. However, since perchloric acid is an extremely strong oxidizing agent that can cause fire and explosion when in contact with combustible materials, its use is best avoided when proper safety equipment and training is unavailable. A comparison was made of four digestion procedures that do not require perchloric acid: wet digestion with nitric and sulfuric acids; wet digestion with nitric acid alone; a repeated wet digestion with nitric acid; and direct dry ashing. Each procedure was used to digest National Bureau of Standards orchard leaves (SRM 1571). To investigate the effect of possible filter paper adsorption on the determination of trace elements, digested samples were either filtered or not filtered before analysis. Atomic absorption spectrophotometry was employed to determine concentrations of As, Be, Cd, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sr, and Zn in each digested sample. Recoveries of each element and the relative error of each determination for each digestion procedure were then calculated. A statistical analysis of these data indicates that the direct dry ashing procedure is best suited for multi-element analysis. Dry ashing is appropriate to recover As, Be, Cr, Cu, Fe, Mn, Mo, Pb, and Zn. The nitric-sulfuric acids, nitric acid, and repeated nitric acid digestion procedures were deemed poor for multi-element analysis; however, each proved useful for the recovery of certain individual elements, including Cd, Pb, and Zn. Sample filtration significantly (p less than or equal to 0.05) lowered the recovery of Cr, Mn, Pb, and Zn from the digested samples. Conversely, the recovery of As, Mo, and Sr was significantly (p less than or equal to 0.05) higher in samples filtered before analysis when compared to the recovery of these elements in unfiltered samples.

  13. Beef, chicken and lamb fatty acid analysis--a simplified direct bimethylation procedure using freeze-dried material.

    PubMed

    Lee, M R F; Tweed, J K S; Kim, E J; Scollan, N D

    2012-12-01

    When fractionation of meat lipids is not required, procedures such as saponification can be used to extract total fatty acids, reducing reliance on toxic organic compounds. However, saponification of muscle fatty acids is laborious, and requires extended heating times, and a second methylation step to convert the extracted fatty acids to fatty acid methyl esters prior to gas chromatography. Therefore the development of a more rapid direct methylation procedure would be of merit. The use of freeze-dried material for analysis is common and allows for greater homogenisation of the sample. The present study investigated the potential of using freeze-dried muscle samples and a direct bimethylation to analyse total fatty acids of meat (beef, chicken and lamb) in comparison with a saponification procedure followed by bimethylation. Both methods compared favourably for all major fatty acids measured. There was a minor difference in relation to the C18:1 trans 10 isomer with a greater (P<0.05) recovery with saponification. However, numerically the difference was small and likely as a result of approaching the limits of isomer identification by single column gas chromatography. Differences (P<0.001) between species were found for all fatty acids measured with no interaction effects. The described technique offers a simplified, quick and reliable alternative to saponification to analyse total fatty acids from muscle samples.

  14. Ultrasound-assisted hydrolysis and chemical derivatization combined to lab-on-valve solid-phase extraction for the determination of sialic acids in human biofluids by μ-liquid chromatography-laser induced fluorescence.

    PubMed

    Orozco-Solano, M I; Priego-Capote, F; Luque de Castro, M D

    2013-03-01

    The determination of sialic acids (SIAs) has recently gained interest because of their potential role as markers of inflammatory disorders or chronic diseases. Hydrolysis of conjugated derivatives, solid-phase extraction (SPE) and derivatization steps constitute sample preparation prior to insertion of the analytical sample into a μ-liquid chromatograph-laser induced fluorescence (μ-LC-LIF) detector in the present method for the determination of two representative SIAs of human metabolism. Ultrasound-accelerated hydrolysis released free SIAs, which were efficiently concentrated in a dynamic manner using a lab-on-valve (LOV) module that allows automation of SPE for preconcentration and cleanup. This step was on-line connected with DMB-labeling of SIAs (derivatization), which was shortened from 180 min required with the conventional heating method to 20min with ultrasound assistance. Individual separation of the target analytes was achieved within 20 min by μ-LC, while LIF detection endowed the overall method with high sensitivity. The LODs and LOQs provided by the method ranged 0.1-0.8 ng mL(-1) and 0.4-1.0 ng mL(-1) (between 0.1-0.8 pg and 0.4-1.0 pg expressed as on-column amount), respectively. High efficiency for interferents removal by SPE enabled the application of the method to four different biofluids-serum, urine, saliva and breast milk-for the determination of the target metabolites.

  15. Ultrasound-assisted hydrolysis and chemical derivatization combined to lab-on-valve solid-phase extraction for the determination of sialic acids in human biofluids by μ-liquid chromatography-laser induced fluorescence.

    PubMed

    Orozco-Solano, M I; Priego-Capote, F; Luque de Castro, M D

    2013-03-01

    The determination of sialic acids (SIAs) has recently gained interest because of their potential role as markers of inflammatory disorders or chronic diseases. Hydrolysis of conjugated derivatives, solid-phase extraction (SPE) and derivatization steps constitute sample preparation prior to insertion of the analytical sample into a μ-liquid chromatograph-laser induced fluorescence (μ-LC-LIF) detector in the present method for the determination of two representative SIAs of human metabolism. Ultrasound-accelerated hydrolysis released free SIAs, which were efficiently concentrated in a dynamic manner using a lab-on-valve (LOV) module that allows automation of SPE for preconcentration and cleanup. This step was on-line connected with DMB-labeling of SIAs (derivatization), which was shortened from 180 min required with the conventional heating method to 20min with ultrasound assistance. Individual separation of the target analytes was achieved within 20 min by μ-LC, while LIF detection endowed the overall method with high sensitivity. The LODs and LOQs provided by the method ranged 0.1-0.8 ng mL(-1) and 0.4-1.0 ng mL(-1) (between 0.1-0.8 pg and 0.4-1.0 pg expressed as on-column amount), respectively. High efficiency for interferents removal by SPE enabled the application of the method to four different biofluids-serum, urine, saliva and breast milk-for the determination of the target metabolites. PMID:23427802

  16. delta 13C analyses of vegetable oil fatty acid components, determined by gas chromatography--combustion--isotope ratio mass spectrometry, after saponification or regiospecific hydrolysis.

    PubMed

    Woodbury, S E; Evershed, R P; Rossell, J B

    1998-05-01

    The delta 13C values of the major fatty acids of several different commercially important vegetable oils were measured by gas chromatography--combustion--isotope ratio mass spectrometry. The delta 13C values obtained were found to fall into two distinct groups, representing the C3 and C4 plants classes from which the oils were derived. The delta 13C values of the oils were measured by continuous flow elemental isotope ratio mass spectrometry and were found to be similar to their fatty acids, with slight differences between individual fatty acids. Investigations were then made into the influence on the delta 13C values of fatty acids of the position occupied on the glycerol backbone. Pancreatic lipase was employed to selectively hydrolyse fatty acids from the 1- and 3-positions with the progress of the reaction being followed by high-temperature gas chromatography in order to determine the optimum incubation time. The 2-monoacylglycerols were then isolated by thin-layer chromatography and fatty acid methyl esters prepared. The delta 13C values obtained indicate that fatty acids from any position on the glycerol backbone are isotopically identical. Thus, whilst quantification of fatty acid composition at the 2-position and measurement of delta 13C values of oils and their major fatty acids are useful criteria in edible oil purity assessment, measurement of delta 13C values of fatty acids from the 2-position does not assist with oil purity assignments.

  17. NREL 2012 Achievement of Ethanol Cost Targets: Biochemical Ethanol Fermentation via Dilute-Acid Pretreatment and Enzymatic Hydrolysis of Corn Stover

    SciTech Connect

    Tao, L.; Schell, D.; Davis, R.; Tan, E.; Elander, R.; Bratis, A.

    2014-04-01

    For the DOE Bioenergy Technologies Office, the annual State of Technology (SOT) assessment is an essential activity for quantifying the benefits of biochemical platform research. This assessment has historically allowed the impact of research progress achieved through targeted Bioenergy Technologies Office funding to be quantified in terms of economic improvements within the context of a fully integrated cellulosic ethanol production process. As such, progress toward the ultimate 2012 goal of demonstrating cost-competitive cellulosic ethanol technology can be tracked. With an assumed feedstock cost for corn stover of $58.50/ton this target has historically been set at $1.41/gal ethanol for conversion costs only (exclusive of feedstock) and $2.15/gal total production cost (inclusive of feedstock) or minimum ethanol selling price (MESP). This year, fully integrated cellulosic ethanol production data generated by National Renewable Energy Laboratory (NREL) researchers in their Integrated Biorefinery Research Facility (IBRF) successfully demonstrated performance commensurate with both the FY 2012 SOT MESP target of $2.15/gal (2007$, $58.50/ton feedstock cost) and the conversion target of $1.41/gal through core research and process improvements in pretreatment, enzymatic hydrolysis, and fermentation.

  18. Pretreating lignocellulosic biomass by the concentrated phosphoric acid plus hydrogen peroxide (PHP) for enzymatic hydrolysis: evaluating the pretreatment flexibility on feedstocks and particle sizes.

    PubMed

    Wang, Qing; Wang, Zhanghong; Shen, Fei; Hu, Jinguang; Sun, Fubao; Lin, Lili; Yang, Gang; Zhang, Yanzong; Deng, Shihuai

    2014-08-01

    In order to seek a high-efficient pretreatment path for converting lignocellulosic feedstocks to fermentable sugars by enzymatic hydrolysis, the concentrated H₃PO₄ plus H₂O₂ (PHP) was attempted to pretreat different lignocellulosic biomass for evaluating the pretreatment flexibility on feedstocks. Meanwhile, the responses of pretreatment to particle sizes were also evaluated. When the PHP-pretreatment was employed (final H₂O₂ and H₃PO₄ concentration of 1.77% and 80.0%), 71-96% lignin and more than 95% hemicellulose in various feedstocks (agricultural residues, hardwood, softwood, bamboo, and their mixture, and garden wastes mixture) can be removed. Consequently, more than 90% glucose conversion was uniformly achieved indicating PHP greatly improved the pretreatment flexibility to different feedstocks. Moreover, when wheat straw and oak chips were PHP-pretreated with different sizes, the average glucose conversion reached 94.9% and 100% with lower coefficient of variation (7.9% and 0.0%), which implied PHP-pretreatment can significantly weaken the negative effects of feedstock sizes on subsequent conversion.

  19. Dilute sulfuric acid pretreatment of corn stover for enzymatic hydrolysis and efficient ethanol production by recombinant Escherichia coli FBR5 without detoxification.

    PubMed

    Avci, Ayse; Saha, Badal C; Kennedy, Gregory J; Cotta, Michael A

    2013-08-01

    A pretreatment strategy for dilute H2SO4 pretreatment of corn stover was developed for the purpose of reducing the generation of inhibitory substances during pretreatment so that a detoxification step is not required prior to fermentation while maximizing sugar yield. The optimal conditions for pretreatment of corn stover (10%, w/v) were: 0.75% H2SO4, 160°C, and 0-5 min holding time. The conditions were chosen based on maximum glucose release after enzymatic hydrolysis, minimum loss of pentose sugars and minimum formation of sugar degradation products such as furfural and hydroxymethyl furfural. The pretreated corn stover after enzymatic saccharification generated 63.2 ± 2.2 and 63.7 ± 2.3 g total sugars per L at 0 and 5 min holding time, respectively. Furfural production was 0.45 ± 0.1 and 0.87 ± 0.4 g/L, respectively. The recombinant Escherichia coli strain FBR5 efficiently fermented non-detoxified corn stover hydrolyzate if the furfural content is <0.5 g/L.

  20. Preservation procedures for arsenic speciation in a stream affected by acid mine drainage in southwestern Spain.

    PubMed

    Sánchez-Rodas, Daniel; Oliveira, Vanesa; Sarmiento, Aguasanta M; Gómez-Ariza, José Luis; Nieto, José Miguel

    2006-04-01

    A preservation study has been performed for arsenic speciation in surface freshwaters affected by acid mine drainage (AMD), a pollution source characterized by low pH and high metallic content. Two sample preservation procedures described in the literature were attempted using opaque glass containers and refrigeration: i) addition of 0.25 mol L(-1) EDTA to the samples, which maintained the stability of the arsenic species for 3 h; and ii) in situ sample clean-up with a cationic exchange resin, in order to reduce the metallic load, which resulted in a partial co-adsorption of arsenic onto Fe precipitates. A new proposed method was also tried: sample acidification with 6 mol L(-1) HCl followed by in situ clean-up with a cationic exchange resin, which allowed a longer preservation time of at least 48 h. The proposed method was successfully applied to water samples with high arsenic content, taken from the Aguas Agrias Stream (Odiel River Basin, SW Spain), which is severely affected by AMD that originates at the nearby polymetallic sulfide mine of Tharsis. The speciation results obtained by liquid chromatography-hydride generation-atomic fluorescence spectrometry (HPLC-HG-AFS) indicated that during the summer the main arsenic species was As(V) at the hundred microg L(-1) level, followed by DMA (dimethyl arsenic) and As(III) below the ten microg L(-1) level. In winter, As(V) and As(III) increased at least fivefold, whereas the DMA was not detected.

  1. Acid-labile mPEG-vinyl ether-1,2-dioleylglycerol lipids with tunable pH sensitivity: synthesis and structural effects on hydrolysis rates, DOPE liposome release performance, and pharmacokinetics.

    PubMed

    Shin, Junhwa; Shum, Pochi; Grey, Jessica; Fujiwara, Shin-ichi; Malhotra, Guarov S; González-Bonet, Andres; Hyun, Seok-Hee; Moase, Elaine; Allen, Theresa M; Thompson, David H

    2012-11-01

    A family of 3-methoxypoly(ethylene glycol)-vinyl ether-1,2-dioleylglycerol (mPEG-VE-DOG) lipopolymer conjugates, designed on the basis of DFT calculations to possess a wide range of proton affinities, was synthesized and tested for their hydrolysis kinetics in neutral and acidic buffers. Extruded ∼100 nm liposomes containing these constructs in ≥90 mol % 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine (DOPE) produced dispersions that retained their calcein cargo for more than 2 days at pH 7.5, but released the encapsulated contents over a wide range of time scales as a function of the electronic properties of the vinyl ether linkage, the solution pH, and the mPEG-VE-DOG composition in the membrane. The in vivo performance of two different 90:10 DOPE:mPEG-VE-DOG compositions was also evaluated for blood circulation time and biodistribution in mice, using (125)I-tyraminylinulin as a label. The pharmacokinetic profiles gave a t(1/2) of 7 and 3 h for 90:10 DOPE:ST302 and 90:10 DOPE:ST502, respectively, with the liposomes being cleared predominantly by liver and spleen uptake. The behavior of these DOPE:mPEG-VE-DOG formulations is consistent with their relative rates of vinyl ether hydrolysis, i.e., the more acid-sensitive mPEG-VE-DOG derivatives produced faster leakage rates from DOPE:mPEG-VE-DOG liposomes, but decreased the blood circulation times in mice. These findings suggest that the vinyl ether-based PEG-lipid derivatives are promising agents for stabilizing acid-sensitive DOPE liposomes to produce formulations with a priori control over their pH responsiveness in vitro. Our data also suggest, however, that the same factors that contribute to enhanced acid sensitivity of the DOPE:mPEG-VE-DOG dispersions are also likely responsible for their reduced pharmacokinetic profiles. PMID:23030381

  2. Acid-labile mPEG-vinyl ether-1,2-dioleylglycerol lipids with tunable pH sensitivity: synthesis and structural effects on hydrolysis rates, DOPE liposome release performance, and pharmacokinetics.

    PubMed

    Shin, Junhwa; Shum, Pochi; Grey, Jessica; Fujiwara, Shin-ichi; Malhotra, Guarov S; González-Bonet, Andres; Hyun, Seok-Hee; Moase, Elaine; Allen, Theresa M; Thompson, David H

    2012-11-01

    A family of 3-methoxypoly(ethylene glycol)-vinyl ether-1,2-dioleylglycerol (mPEG-VE-DOG) lipopolymer conjugates, designed on the basis of DFT calculations to possess a wide range of proton affinities, was synthesized and tested for their hydrolysis kinetics in neutral and acidic buffers. Extruded ∼100 nm liposomes containing these constructs in ≥90 mol % 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine (DOPE) produced dispersions that retained their calcein cargo for more than 2 days at pH 7.5, but released the encapsulated contents over a wide range of time scales as a function of the electronic properties of the vinyl ether linkage, the solution pH, and the mPEG-VE-DOG composition in the membrane. The in vivo performance of two different 90:10 DOPE:mPEG-VE-DOG compositions was also evaluated for blood circulation time and biodistribution in mice, using (125)I-tyraminylinulin as a label. The pharmacokinetic profiles gave a t(1/2) of 7 and 3 h for 90:10 DOPE:ST302 and 90:10 DOPE:ST502, respectively, with the liposomes being cleared predominantly by liver and spleen uptake. The behavior of these DOPE:mPEG-VE-DOG formulations is consistent with their relative rates of vinyl ether hydrolysis, i.e., the more acid-sensitive mPEG-VE-DOG derivatives produced faster leakage rates from DOPE:mPEG-VE-DOG liposomes, but decreased the blood circulation times in mice. These findings suggest that the vinyl ether-based PEG-lipid derivatives are promising agents for stabilizing acid-sensitive DOPE liposomes to produce formulations with a priori control over their pH responsiveness in vitro. Our data also suggest, however, that the same factors that contribute to enhanced acid sensitivity of the DOPE:mPEG-VE-DOG dispersions are also likely responsible for their reduced pharmacokinetic profiles.

  3. Epidemic based modeling of enzymatic hydrolysis of lignocellulosic biomass.

    PubMed

    Tai, Chao; Arellano, Maria G; Keshwani, Deepak R

    2014-01-01

    An epidemic based model was developed to describe the enzymatic hydrolysis of a lignocellulosic biomass, dilute sulfuric acid pretreated corn stover. The process of substrate getting adsorbed and digested by enzyme was simulated as susceptibles getting infected by viruses and becoming removed and recovered. This model simplified the dynamic enzyme "infection" process and the catalysis of cellulose into a two-parameter controlled, enzyme behavior guided mechanism. Furthermore, the model incorporates the adsorption block by lignin and inhibition effects on cellulose catalysis. The model satisfactorily predicted the enzyme adsorption and hydrolysis, negative role of lignin, and inhibition effects over hydrolysis for a broad range of substrate and enzyme loadings. Sensitivity analysis was performed to evaluate the incorporation of lignin and other inhibition effects. Our model will be a useful tool for evaluating the effects of parameters during hydrolysis and guide a design strategy for continuous hydrolysis and the associated process control.

  4. Determination of Total Lipids as Fatty Acid Methyl Esters (FAME) by in situ Transesterification: Laboratory Analytical Procedure (LAP)

    SciTech Connect

    Van Wychen, S.; Laurens, L. M. L.

    2013-12-01

    This procedure is based on a whole biomass transesterification of lipids to fatty acid methyl esters to represent an accurate reflection of the potential of microalgal biofuels. Lipids are present in many forms and play various roles within an algal cell, from cell membrane phospholipids to energy stored as triacylglycerols.

  5. Luminescent silica nanoparticles for sensing acetylcholinesterase-catalyzed hydrolysis of acetylcholine.

    PubMed

    Mukhametshina, Alsu R; Fedorenko, Svetlana V; Zueva, Irina V; Petrov, Konstantin A; Masson, Patrick; Nizameev, Irek R; Mustafina, Asiya R; Sinyashin, Oleg G

    2016-03-15

    This work highlights the H-function of Tb(III)-doped silica nanoparticles in aqueous solutions of acetic acid as a route to sense acetylcholinesterase-catalyzed hydrolysis of acetylcholine (ACh). The H-function results from H(+)-induced quenching of Tb(III)-centered luminescence due to protonation of Tb(III) complexes located close to silica/water interface. The H-function can be turned on/switched off by the concentration of complexes within core or nanoparticle shell zones, by the silica surface decoration and adsorption of both organic and inorganic cations on silica surface. Results indicate the optimal synthetic procedure for making nanoparticles capable of sensing acetic acid produced by enzymatic hydrolysis of acetylcholine. The H-function of nanoparticles was determined at various concentrations of ACh and AChE. The measurements show experimental conditions for fitting the H-function to Michaelis-Menten kinetics. Results confirm that reliable fluorescent monitoring AChE-catalyzed hydrolysis of ACh is possible through the H-function properties of Tb(III)-doped silica nanoparticles.

  6. Luminescent silica nanoparticles for sensing acetylcholinesterase-catalyzed hydrolysis of acetylcholine.

    PubMed

    Mukhametshina, Alsu R; Fedorenko, Svetlana V; Zueva, Irina V; Petrov, Konstantin A; Masson, Patrick; Nizameev, Irek R; Mustafina, Asiya R; Sinyashin, Oleg G

    2016-03-15

    This work highlights the H-function of Tb(III)-doped silica nanoparticles in aqueous solutions of acetic acid as a route to sense acetylcholinesterase-catalyzed hydrolysis of acetylcholine (ACh). The H-function results from H(+)-induced quenching of Tb(III)-centered luminescence due to protonation of Tb(III) complexes located close to silica/water interface. The H-function can be turned on/switched off by the concentration of complexes within core or nanoparticle shell zones, by the silica surface decoration and adsorption of both organic and inorganic cations on silica surface. Results indicate the optimal synthetic procedure for making nanoparticles capable of sensing acetic acid produced by enzymatic hydrolysis of acetylcholine. The H-function of nanoparticles was determined at various concentrations of ACh and AChE. The measurements show experimental conditions for fitting the H-function to Michaelis-Menten kinetics. Results confirm that reliable fluorescent monitoring AChE-catalyzed hydrolysis of ACh is possible through the H-function properties of Tb(III)-doped silica nanoparticles. PMID:26516688

  7. Continuous steam hydrolysis of tulip poplar

    SciTech Connect

    Fieber, C.; Colcord, A.R.; Faass, S.; Muzzy, J.D.; Roberts, R.S.

    1982-08-01

    To produce ethanol from hardwood it is desirable to fractionate the hardwood in order to produce a relatively pure cellulosic pulp for dilute acid hydrolysis. An experimental investigation of continuous steam hydrolysis of tulip poplar wood chips indicates that over 90% of the lignin present can be extracted by 0.1N sodium hydroxide, resulting in a cellulose pulp containing over 90% hexosan. The study was performed using a Stake Technology, Ltd., continuous digester rated at one oven dry ton per hour of wood chips. The yields of hexosans, hexoses, xylan, xylose, lignin, furfural, acetic acid and methanol were determined as a function of residence time and steam pressure in the digester. The information provides a basis for establishing a material and energy balance for a hardwood to ethanol plant.

  8. Non-ionic surfactants do not consistently improve the enzymatic hydrolysis of pure cellulose.

    PubMed

    Zhou, Yan; Chen, Hongmei; Qi, Feng; Zhao, Xuebing; Liu, Dehua

    2015-04-01

    Non-ionic surfactants have been frequently reported to improve the enzymatic hydrolysis of pretreated lignocellulosic biomass and pure cellulose. However, how the hydrolysis condition, substrate structure and cellulase formulation affect the beneficial action of surfactants has not been well elucidated. In this work, it was found that the enzymatic hydrolysis of pure cellulose was not consistently improved by surfactants. Contrarily, high surfactant concentration, e.g. 5 g/L, which greatly improved the hydrolysis of dilute acid pretreated substrates, actually showed notable inhibition to pure cellulose conversion in the late phase of hydrolysis. Under an optimal hydrolysis condition, the improvement by surfactant was limited, but under harsh conditions surfactant indeed could enhance cellulose conversion. It was proposed that non-ionic surfactants could interact with substrates and cellulases to impact the adsorption behaviors of cellulases. Therefore, the beneficial action of surfactants on pure cellulose hydrolysis is influenced by hydrolysis condition, cellulose structural features and cellulase formulation.

  9. PLA recycling by hydrolysis at high temperature

    NASA Astrophysics Data System (ADS)

    Cristina, Annesini Maria; Rosaria, Augelletti; Sara, Frattari; Fausto, Gironi

    2016-05-01

    In this work the process of PLA hydrolysis at high temperature was studied, in order to evaluate the possibility of chemical recycling of this polymer bio-based. In particular, the possibility to obtain the monomer of lactic acid from PLA degradation was investigated. The results of some preliminary tests, performed in a laboratory batch reactor at high temperature, are presented: the experimental results show that the complete degradation of PLA can be obtained in relatively low reaction times.

  10. Development of complete hydrolysis of pectins from apple pomace.

    PubMed

    Wikiera, Agnieszka; Mika, Magdalena; Starzyńska-Janiszewska, Anna; Stodolak, Bożena

    2015-04-01

    Enzymatically extracted pectins have a more complex structure than those obtained by conventional methods. As a result, they are less susceptible to hydrolysis, which makes the precise determination of their composition difficult. The aim of the study was to develop a method of complete hydrolysis of enzymatically extracted apple pectins. Substrates were pectins isolated from apple pomace by the use of xylanase and multicatalytic preparation Celluclast and apple pomace. Hydrolysis was performed by a chemical method with 2M TFA at 100 °C and 120 °C and a combined acidic/enzymatic method. After hydrolysis, the contents of galacturonic acid and neutral sugars were measured by HPLC. Complete hydrolysis of polygalacturonic acid occurred after 2.5h incubation with 2M TFA at 120 °C. The efficient hydrolysis of neutral sugars in pectins was performed with 2M TFA at 100 °C for 2.5h. Monomers most susceptible to concentrated acid were rhamnose, mannose and arabinose.

  11. Development of complete hydrolysis of pectins from apple pomace.

    PubMed

    Wikiera, Agnieszka; Mika, Magdalena; Starzyńska-Janiszewska, Anna; Stodolak, Bożena

    2015-04-01

    Enzymatically extracted pectins have a more complex structure than those obtained by conventional methods. As a result, they are less susceptible to hydrolysis, which makes the precise determination of their composition difficult. The aim of the study was to develop a method of complete hydrolysis of enzymatically extracted apple pectins. Substrates were pectins isolated from apple pomace by the use of xylanase and multicatalytic preparation Celluclast and apple pomace. Hydrolysis was performed by a chemical method with 2M TFA at 100 °C and 120 °C and a combined acidic/enzymatic method. After hydrolysis, the contents of galacturonic acid and neutral sugars were measured by HPLC. Complete hydrolysis of polygalacturonic acid occurred after 2.5h incubation with 2M TFA at 120 °C. The efficient hydrolysis of neutral sugars in pectins was performed with 2M TFA at 100 °C for 2.5h. Monomers most susceptible to concentrated acid were rhamnose, mannose and arabinose. PMID:25442606

  12. Thioglycoside hydrolysis catalyzed by {beta}-glucosidase

    SciTech Connect

    Shen Hong; Byers, Larry D.

    2007-10-26

    Sweet almond {beta}-glucosidase (EC 3.2.1.21) has been shown to have significant thioglycohydrolase activity. While the K{sub m} values for the S- and O-glycosides are similar, the k{sub cat} values are about 1000-times lower for the S-glycosides. Remarkably, the pH-profile for k{sub cat}/K{sub m} for hydrolysis of p-nitrophenyl thioglucoside (pNPSG) shows the identical dependence on a deprotonated carboxylate (pK{sub a} 4.5) and a protonated group (pK{sub a} 6.7) as does the pH-profile for hydrolysis of the corresponding O-glycoside. Not surprisingly, in spite of the requirement for the presence of this protonated group in catalytically active {beta}-glucosidase, thioglucoside hydrolysis does not involve general acid catalysis. There is no solvent kinetic isotope effect on the enzyme-catalyzed hydrolysis of pNPSG.

  13. Comparison of polysaccharides of Haliotis discus hannai and Volutharpa ampullacea perryi by PMP-HPLC-MS(n) analysis upon acid hydrolysis.

    PubMed

    Wang, Hongxu; Zhao, Jun; Li, Dongmei; Wen, Chengrong; Liu, Haiman; Song, Shuang; Zhu, Beiwei

    2015-10-13

    Haliotis discus hannai Ino (Haliotis) is a highly valued marine shellfish, and it is sometimes replaced by another cheaper Gastropoda mollusk, Volutharpa ampullacea perryi (Volutharpa). Polysaccharides from pleopods, viscera and gonads of these two gastropods were compared by analyzing the mono- and di-saccharides in their acid hydrolysates using high performance liquid chromatography-mass spectrometry (HPLC-MS(n)) after 1-phenyl-3-methyl-5-pyrazolone (PMP) derivatization. Disaccharide analysis revealed the distribution of uronic acid-containing polysaccharides (UACPs) in the biological samples. GlcA-(1 → 2)-Man, GlcA-(1 → 3)-GalN, and another disaccharide consisting of a hexuronic acid linked to a hexose were found in the hydrolysates, which indicated the existence of AGSP (abalone gonad sulfated polysaccharide) with the backbone composed of → 2)-α-Man(1 → 4)-β-GlcA(1 → repeating unit, AAP (abalone glycosaminoglycan-like polysaccharide) with the backbone of → 3)-GalNAc-(1 → 2)-GlcA-(1 → 3)-GalNAc-(1 → 4)-GlcA-(1 → repeating unit, and unidentified DS1P containing a hexuronic acid linked to a hexose unit, respectively. As shown by extracted ion chromatograms (XICs), AAP was the only UACP found in pleopods of the two gastropods; gonads and viscera of Haliotis contained DS1P and AGSP, while those of Volutharpa contained DS1P, AGSP as well as AAP. Monosaccharides in the acid hydrolysates were demonstrated in XICs by extracting their corresponding PMP derivative quasi-molecular ions one by one, and the results indicated the similar conclusion to the disaccharide analysis. Therefore, it could be concluded that polysaccharides from pleopods of the two gastropods are very similar, while those from their viscera and gonads differ greatly. PMID:26279526

  14. Comparison of polysaccharides of Haliotis discus hannai and Volutharpa ampullacea perryi by PMP-HPLC-MS(n) analysis upon acid hydrolysis.

    PubMed

    Wang, Hongxu; Zhao, Jun; Li, Dongmei; Wen, Chengrong; Liu, Haiman; Song, Shuang; Zhu, Beiwei

    2015-10-13

    Haliotis discus hannai Ino (Haliotis) is a highly valued marine shellfish, and it is sometimes replaced by another cheaper Gastropoda mollusk, Volutharpa ampullacea perryi (Volutharpa). Polysaccharides from pleopods, viscera and gonads of these two gastropods were compared by analyzing the mono- and di-saccharides in their acid hydrolysates using high performance liquid chromatography-mass spectrometry (HPLC-MS(n)) after 1-phenyl-3-methyl-5-pyrazolone (PMP) derivatization. Disaccharide analysis revealed the distribution of uronic acid-containing polysaccharides (UACPs) in the biological samples. GlcA-(1 → 2)-Man, GlcA-(1 → 3)-GalN, and another disaccharide consisting of a hexuronic acid linked to a hexose were found in the hydrolysates, which indicated the existence of AGSP (abalone gonad sulfated polysaccharide) with the backbone composed of → 2)-α-Man(1 → 4)-β-GlcA(1 → repeating unit, AAP (abalone glycosaminoglycan-like polysaccharide) with the backbone of → 3)-GalNAc-(1 → 2)-GlcA-(1 → 3)-GalNAc-(1 → 4)-GlcA-(1 → repeating unit, and unidentified DS1P containing a hexuronic acid linked to a hexose unit, respectively. As shown by extracted ion chromatograms (XICs), AAP was the only UACP found in pleopods of the two gastropods; gonads and viscera of Haliotis contained DS1P and AGSP, while those of Volutharpa contained DS1P, AGSP as well as AAP. Monosaccharides in the acid hydrolysates were demonstrated in XICs by extracting their corresponding PMP derivative quasi-molecular ions one by one, and the results indicated the similar conclusion to the disaccharide analysis. Therefore, it could be concluded that polysaccharides from pleopods of the two gastropods are very similar, while those from their viscera and gonads differ greatly.

  15. Process Design Report for Wood Feedstock: Lignocellulosic Biomass to Ethanol Process Desing and Economics Utilizing Co-Current Dilute Acid Prehydrolysis and Enzymatic Hydrolysis Current and Futuristic Scenarios

    SciTech Connect

    Wooley, Robert; Ruth, Mark; Sheehan, John; Ibsen, Kelly; Majdeski, Henry; Galves, Adrian

    1999-07-01

    The National Renewable Energy Laboratory (NREL) has undertaken a complete review and update of the process design and economic model for the biomass-to-ethanol process based on co-current dilute acid prehydrolysis, along with simultaneous saccharification (enzymatic) and co-fermentation. The process design includes the core technologies being researched by the U.S. Department of Energy (DOE): prehydrolysis, simultaneous saccharification and co-fermentation, and cellulase enzyme production.

  16. Influence of manufacturing procedure on the compositional and sensory properties of n-3 fatty acid-enriched pecorino cheese.

    PubMed

    Branciari, Raffaella; Mughetti, Laura; Ranucci, David; Miraglia, Dino; Valiani, Andrea; Acuti, Gabriele; Selvaggini, Roberto; Trabalza-Marinucci, Massimo

    2014-11-01

    Pecorino cheeses were produced using two different manufacturing procedures (either from raw milk or from milk previously subject to a thermisation at 65 °C for 10 s with the addition of starter culture) using the milk obtained from three groups of ewes fed three different concentrates: (1) control, (2) control enriched with 100 g/kg of extruded linseed, and (3) control enriched with 200 g/kg of extruded linseed. All concentrates were administered with alfalfa hay ad libitum. The extruded linseed-enriched diets increased the concentration of n-3 fatty acids, conjugated linoleic acid, and monounsaturated and polyunsaturated acids in raw milk and thermised milk cheese and decreased the concentration of saturated fatty acids. Changes in the manufacturing procedure did not influence the fatty acid composition of the cheeses but markedly influenced their sensory properties. In particular, heat-treating the milk and adding a starter reduced the differences in cheese odour, flavour and toughness induced by the diet when raw milk was used. Cheeses made with thermised milk and the addition of starter culture were more uniform and obtained a higher score in the preference test compared with the corresponding raw milk cheeses. An appropriate manufacturing process, therefore, can be a possible strategy to obtain cheeses with improved health-promoting properties and an unaltered acceptance level by consumers.

  17. Hydrolysis of biomass material

    DOEpatents

    Schmidt, Andrew J.; Orth, Rick J.; Franz, James A.; Alnajjar, Mikhail

    2004-02-17

    A method for selective hydrolysis of the hemicellulose component of a biomass material. The selective hydrolysis produces water-soluble small molecules, particularly monosaccharides. One embodiment includes solubilizing at least a portion of the hemicellulose and subsequently hydrolyzing the solubilized hemicellulose to produce at least one monosaccharide. A second embodiment includes solubilizing at least a portion of the hemicellulose and subsequently enzymatically hydrolyzing the solubilized hemicellulose to produce at least one monosaccharide. A third embodiment includes solubilizing at least a portion of the hemicellulose by heating the biomass material to greater than 110.degree. C. resulting in an aqueous portion that includes the solubilized hemicellulose and a water insoluble solids portion and subsequently separating the aqueous portion from the water insoluble solids portion. A fourth embodiment is a method for making a composition that includes cellulose, at least one protein and less than about 30 weight % hemicellulose, the method including solubilizing at least a portion of hemicellulose present in a biomass material that also includes cellulose and at least one protein and subsequently separating the solubilized hemicellulose from the cellulose and at least one protein.

  18. The antioxidant and chlorogenic acid profiles of whole coffee fruits are influenced by the extraction procedures.

    PubMed

    Mullen, W; Nemzer, B; Ou, B; Stalmach, A; Hunter, J; Clifford, M N; Combet, E

    2011-04-27

    Commercial whole coffee fruit extracts and powder samples were analyzed for chlorogenic acids (CGA), caffeine and antioxidant activities. CGA and caffeine were characterized by LC-MS(n) and HPLC accordingly, and quantified by UV absorbance. ORAC, HORAC, NORAC, SORAC and SOAC (antioxidant capacities) were assessed. Three caffeoylquinic acids, three feruloylquinic acids, three dicaffeoylquinic acids, one p-coumaroylquinic acid, two caffeoylferuloylquinic acids and three putative chlorogenic lactones were quantified, along with a methyl ester of 5-caffeoylquinic acid (detected in one sample, the first such report in any coffee material). Multistep whole coffee fruit extracts displayed higher CGA content than single-step extracts, freeze-dried, or air-dried whole raw fruits. Caffeine in multistep extracts was lower than in the single-step extracts and powders. Antioxidant activity in whole coffee fruit extracts was up to 25-fold higher than in powders dependent upon the radical. Total antioxidant activity of samples displayed strong correlation to CGA content. PMID:21401105

  19. Homogeneous catalysis of valeronitrile hydrolysis under supercritical conditions.

    PubMed

    Sarlea, Michael; Kohl, Sabine; Blickhan, Nina; Vogel, Herbert

    2012-01-01

    Supercritical nitrile hydrolysis can be used for both, amide and acid production as well as waste water treatment, as the hydrolysis products show good biodegradability. The conventional process at ambient conditions requires large amounts of mineral acid or base. Approaches that use supercritical water as a green solvent without a catalyst have been investigated over recent years. Findings for valeronitrile hydrolysis presented recently showed promising reaction rates and valeric acid yields. In an attempt to further maximize product yield and to better understand the impact of the pH, reactions in dilute sulfuric acid (0.01 mol L(-1)) were performed in a continuous high-pressure laboratory-scale apparatus at 400-500 °C, 30 MPa, and a maximum residence time of 100 s. Results from both reaction media were compared with regard to productivity and sustainability.

  20. Use of an algal hydrolysate to improve enzymatic hydrolysis of anaerobically digested fiber

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This study investigated the use of acid hydrolyzed algae to enhance the enzymatic hydrolysis of cellulosic biomass. We first characterized wastewater-grown algal samples and determined the optimal conditions (acid concentration, reaction temperature, and reaction time) for algal hydrolysis using di...

  1. Challenges with fats and fatty acid methods.

    PubMed

    Palmquist, D L; Jenkins, T C

    2003-12-01

    The content and chemical nature of lipids in feedstuffs is heterogeneous. It has long been known that ether extraction by the Weende procedure inadequately characterizes the fat content of feedstuffs, yet it remains the official method. Diethyl ether (or hexanes that are often used) extracts significant amounts of nonnutritive, nonsaponifiable lipids from forages, and often incompletely extracts lipids of nutritional value, especially fatty acids present as salts of divalent cations. Preextraction hydrolysis of insoluble fatty acid salts with acid releases these fatty acids, and this step is included in the official procedure for certain feedstuffs in the United Kingdom; however, acid hydrolysis increases analysis time and decreases precision. Acid hydrolysis also causes confusion as to the proper definition of the fat content of feedstuffs. A preferred method of fat analysis determines the total fatty acid concentration in feed samples by converting fatty acid salts, as well as the acyl components in all lipid classes, such as triacylglycerols, phospholipids, and sphingolipids, to methyl esters using a simple, direct one-step esterification procedure. Fatty acid methyl esters are then quantified by GLC, which provides information on both fatty acid quantity and profile in a single analysis. Adjustments in conditions and reagents may be necessary to overcome difficulty in quantitatively preparing esters from certain types of fatty acids and their derivatives in commercial fat supplements. After correction for glycerol content, analysis of oils by this procedure provides information on the content of nonsaponifiable material, such as chlorophyll, waxes, and indigestible polymers formed from heat- or oxidatively damaged fats. The correct description of feedstuffs for energy value of fats is the content of total fatty acids. PMID:14677882

  2. Development of a nucleic Acid extraction procedure for simultaneous recovery of DNA and RNA from diverse microbes in water.

    PubMed

    Hill, Vincent R; Narayanan, Jothikumar; Gallen, Rachel R; Ferdinand, Karen L; Cromeans, Theresa; Vinjé, Jan

    2015-01-01

    Drinking and environmental water samples contain a diverse array of constituents that can interfere with molecular testing techniques, especially when large volumes of water are concentrated to the small volumes needed for effective molecular analysis. In this study, a suite of enteric viruses, bacteria, and protozoan parasites were seeded into concentrated source water and finished drinking water samples, in order to investigate the relative performance of nucleic acid extraction techniques for molecular testing. Real-time PCR and reverse transcription-PCR crossing threshold (CT) values were used as the metrics for evaluating relative performance. Experimental results were used to develop a guanidinium isothiocyanate-based lysis buffer (UNEX buffer) that enabled effective simultaneous extraction and recovery of DNA and RNA from the suite of study microbes. Procedures for bead beating, nucleic acid purification, and PCR facilitation were also developed and integrated in the protocol. The final lysis buffer and sample preparation procedure was found to be effective for a panel of drinking water and source water concentrates when compared to commercial nucleic acid extraction kits. The UNEX buffer-based extraction protocol enabled PCR detection of six study microbes, in 100 L finished water samples from four drinking water treatment facilities, within three CT values (i.e., within 90% difference) of the reagent-grade water control. The results from this study indicate that this newly formulated lysis buffer and sample preparation procedure can be useful for standardized molecular testing of drinking and environmental waters.

  3. A Series of α-Amino Acid Ester Prodrugs of Camptothecin: In vitro Hydrolysis and A549 Human Lung Carcinoma Cell Cytotoxicity

    PubMed Central

    Deshmukh, Manjeet; Chao, Piyun; Kutscher, Hilliard L.; Gao, Dayuan; Sinko, Patrick J.

    2013-01-01

    The objective of the present study was to identify a camptothecin (CPT) prodrug with optimal release and cytotoxicity properties for immobilization on a passively targeted microparticle delivery system. A series of α-amino acid ester prodrugs of CPT were synthesized, characterized and evaluated. Four CPT prodrugs were synthesized with increasing aliphatic chain length (glycine (Gly) (2a), alanine (Ala) (2b), aminobutyric acid (Abu) (2c) and norvaline (Nva) (2d)). Prodrug reconversion was studied at pH 6.6, 7.0 and 7.4 corresponding to tumor, lung and extracellular/physiological pH, respectively. Cytotoxicity was evaluated in A549 human lung carcinoma cells using 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. The hydrolytic reconversion rate to parent CPT increased with decreasing side chain length as well as increasing pH. The Hill slope of 2d was significantly less than CPT and the other prodrugs tested, indicating a higher cell death rate at lower concentrations. These results suggest that 2d is the best candidate for a passively targeted sustained release lung delivery system. PMID:20063889

  4. Enzymatic hydrolysis of poly(ethylene furanoate).

    PubMed

    Pellis, Alessandro; Haernvall, Karolina; Pichler, Christian M; Ghazaryan, Gagik; Breinbauer, Rolf; Guebitz, Georg M

    2016-10-10

    The urgency of producing new environmentally-friendly polyesters strongly enhanced the development of bio-based poly(ethylene furanoate) (PEF) as an alternative to plastics like poly(ethylene terephthalate) (PET) for applications that include food packaging, personal and home care containers and thermoforming equipment. In this study, PEF powders of various molecular weights (6, 10 and 40kDa) were synthetized and their susceptibility to enzymatic hydrolysis was investigated for the first time. According to LC/TOF-MS analysis, cutinase 1 from Thermobifida cellulosilytica liberated both 2,5-furandicarboxylic acid and oligomers of up to DP4. The enzyme preferentially hydrolyzed PEF with higher molecular weights but was active on all tested substrates. Mild enzymatic hydrolysis of PEF has a potential both for surface functionalization and monomers recycling. PMID:26854948

  5. Alkali hydrolysis of trinitrotoluene.

    PubMed

    Karasch, Christian; Popovic, Milan; Qasim, Mohamed; Bajpai, Rakesh K

    2002-01-01

    Data for alkali hydrolysis of 2,4,6-trinitrotoluene (TNT) in aqueous solution at pH 12.0 under static (pH-controlled) as well as dynamic (pH-uncontrolled) conditions are reported. The experiments were conducted at two different molar ratios of TNT to hydroxyl ions at room temperature. The TNT disappeared rapidly from the solution as a first-order reaction. The complete disappearance of aromatic structure from the aqueous solution within 24 h was confirmed by the ultraviolet-visible (UV-VIS) spectra of the samples. Cuvet experiments in a UV-VIS spectrophotometer demonstrated the formation of Meisenheimer complex, which slowly disappeared via formation of aromatic compounds with fewer nitro groups. The known metabolites of TNT were found to accumulate only in very small quantities in the liquid phase.

  6. Chromatographic determination of amino acids in foods.

    PubMed

    Peace, Robert W; Gilani, G Sarwar

    2005-01-01

    Amino acids in foods exist in a free form or bound in peptides, proteins, or nonpeptide bonded polymers. Naturally occurring L-amino acids are required for protein synthesis and are precursors for essential molecules, such as co-enzymes and nucleic acids. Nonprotein amino acids may also occur in animal tissues as metabolic intermediates or have other important functions. The development of bacterially derived food proteins, genetically modified foods, and new methods of food processing; the production of amino acids for food fortification; and the introduction of new plant food sources have meant that protein amino acids and amino acid enantiomers in foods can have both nutritional and safety implications for humans. There is, therefore, a need for the rapid and accurate determination of amino acids in foods. Determination of the total amino acid content of foods requires protein hydrolysis by various means that must take into account variations in stability of individual amino acids and resistance of different peptide bonds to the hydrolysis procedures. Modern methods for separation and quantitation of free amino acids either before or after protein hydrolysis include ion exchange chromatography, high performance liquid chromatography (LC), gas chromatography, and capillary electrophoresis. Chemical derivatization of amino acids may be required to change them into forms amenable to separation by the various chromatographic methods or to create derivatives with properties, such as fluorescence, that improve their detection. Official methods for hydrolysis and analysis of amino acids in foods for nutritional purposes have been established. LC is currently the most widely used analytical technique, although there is a need for collaborative testing of methods available. Newer developments in chromatographic methodology and detector technology have reduced sample and reagent requirements and improved identification, resolution, and sensitivity of amino acid analyses

  7. Comparison of different pretreatment strategies for enzymatic hydrolysis of wheat and barley straw.

    PubMed

    Rosgaard, Lisa; Pedersen, Sven; Meyer, Anne S

    2007-12-01

    In biomass-to-ethanol processes a physico-chemical pretreatment of the lignocellulosic biomass is a critical requirement for enhancing the accessibility of the cellulose substrate to enzymatic attack. This report evaluates the efficacy on barley and wheat straw of three different pretreatment procedures: acid or water impregnation followed by steam explosion versus hot water extraction. The pretreatments were compared after enzyme treatment using a cellulase enzyme system, Celluclast 1.5 L from Trichoderma reesei, and a beta-glucosidase, Novozyme 188 from Aspergillus niger. Barley straw generally produced higher glucose concentrations after enzymatic hydrolysis than wheat straw. Acid or water impregnation followed by steam explosion of barley straw was the best pretreatment in terms of resulting glucose concentration in the liquid hydrolysate after enzymatic hydrolysis. When the glucose concentrations obtained after enzymatic hydrolyses were related to the potential glucose present in the pretreated residues, the highest yield, approximately 48% (g g-1), was obtained with hot water extraction pretreatment of barley straw; this pretreatment also produced highest yields for wheat straw, producing a glucose yield of approximately 39% (g g-1). Addition of extra enzyme (Celluclast 1.5 L+Novozyme 188) during enzymatic hydrolysis resulted in the highest total glucose concentrations from barley straw, 32-39 g L-1, but the relative increases in glucose yields were higher on wheat straw than on barley straw. Maldi-TOF MS analyses of supernatants of pretreated barley and wheat straw samples subjected to acid and water impregnation, respectively, and steam explosion, revealed that the water impregnated + steam-exploded samples gave a wider range of pentose oligomers than the corresponding acid-impregnated samples.

  8. Surveying Students' Conceptual and Procedural Knowledge of Acid-Base Behavior of Substances

    ERIC Educational Resources Information Center

    Furio-Mas, Carles; Calatayud, Maria-Luisa; Barcenas, Sergio L.

    2007-01-01

    By the end of their high school studies, students should be able to understand macroscopic and sub-microscopic conceptualization of acid-base behavior and the relationship between these conceptual models. The aim of this article is to ascertain whether grade-12 students have sufficient background knowledge to explain the properties of acids,…

  9. Construction of wettability gradient surface on copper substrate by controlled hydrolysis of poly(methyl methacrylate-butyl acrylate) films

    NASA Astrophysics Data System (ADS)

    Zhang, Yong; Cheng, Jiang; Yang, Zhuo-ru

    2014-10-01

    We report a gradient wettability surface on copper slide prepared by a simple controlled ester group hydrolysis procedure of poly(methyl methacrylate-butyl acrylate) [P (MMA-BA)] films coated on the copper substrate. In the method, sodium hydroxide solutions are selected to prepare surface gradient wettability on P (MMA-BA) films. The P (MMA-BA) copolymers with different MMA contents are first synthesized by a conventional free atom radical solution polymerization method. The transfer of surface chemical composition from the ester group to acid salt is achieved by hydrolysis in NaOH solution. The effects of different concentrations of NaOH solution and reaction times on the physicochemical properties of the resulting surfaces are studied. The field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) results show that the varying concentration along the substrate length is only attributed to the hydrolysis reaction of ester groups. The hydrolysis causes insignificant change on the morphology of the original film on the copper substrate. In addition, it is found that the MMA copolymer content has a significant influence on the concentration of ester groups on the outermost surface and thus important for forming the slope gradients.

  10. Acid-base properties of the alumina surface: influence of the titration procedures on the microcalorimetric results.

    PubMed

    Morel, Jean-Pierre; Marmier, Nicolas; Hurel, Charlotte; Morel-Desrosiers, Nicole

    2009-10-01

    The enthalpy changes associated with the protonation and deprotonation of an alumina surface have been determined on the basis of microcalorimetry experiments and acid-base potentiometric titrations at 25 degrees C. It has been shown that the results may vary significantly according to the experimental procedure. In order to do so, the potentiometric and microcalorimetric titrations have been carried out first from an acidic pH to basic pH and second from a pH near the pH(zpc) of alumina to acidic or basic pH. It has been demonstrated that the pK(a) values deduced from the potentiometric titrations are the same whatever the experimental protocol whereas the only way to obtain meaningful enthalpies of proton exchange is to carry out microcalorimetric titrations by starting around the point of zero charge.

  11. Methods of analysis by the U.S. Geological Survey National Water Quality Laboratory; comparison of a nitric acid in-bottle digestion procedure to other whole-water digestion procedures

    USGS Publications Warehouse

    Garbarino, John R.; Hoffman, Gerald L.

    1999-01-01

    A hydrochloric acid in-bottle digestion procedure is used to partially digest wholewater samples prior to determining recoverable elements by various analytical methods. The use of hydrochloric acid is problematic for some methods of analysis because of spectral interference. The inbottle digestion procedure has been modified to eliminate such interference by using nitric acid instead of hydrochloric acid in the digestion. Implications of this modification are evaluated by comparing results for a series of synthetic whole-water samples. Results are also compared with those obtained by using U.S. Environmental Protection Agency (1994) (USEPA) Method 200.2 total-recoverable digestion procedure. Percentage yields that use the nitric acid inbottle digestion procedure are within 10 percent of the hydrochloric acid in-bottle yields for 25 of the 26 elements determined in two of the three synthetic whole-water samples tested. Differences in percentage yields for the third synthetic whole-water sample were greater than 10 percent for 16 of the 26 elements determined. The USEPA method was the most rigorous for solubilizing elements from particulate matter in all three synthetic whole-water samples. Nevertheless, the variability in the percentage yield by using the USEPA digestion procedure was generally greater than the in-bottle digestion procedure, presumably because of the difficulty in controlling the digestion conditions accurately.

  12. Hydrolysis and esterification in organically modified alkoxysilanes: A {sup 29}Si NMR investigation of methyltrimethoxysilane

    SciTech Connect

    Alam, T.M.; Assink, R.A.; Loy, D.A.

    1996-09-01

    High-resolution {sup 29}Si NMR was used to investigate the acid-catalyzed hydrolysis and esterification reactions of methyltrimethoxysilane (MTMS) in methanol. The INEPT experiment, adapted for spin systems with multiple heteronuclear coupling constants, was used to assign the closely spaced resonances of the MTMS hydrolysis products. Due to the rapid reaction rates, only the pseudoequilibrium concentration distributions for the resulting hydrolysis products could be determined. Models based on thermodynamically statistical distributions, irreversible hydrolysis reactions, and reversible hydrolysis reactions were nearly equally successful in accounting for the concentration distributions over a wide range of H{sub 2}O/Si ratios (R{sub w}) and temperatures. However, preparation of hydrolyzed MTMS in a nonpseudoequilibrium state unequivocally demonstrated the reversibility of hydrolysis reactions on a short time scale. By measuring the extent of reaction of MTMS systems at high water concentrations, the ratio of the hydrolysis to esterification rate constant was determined to be approximately 100. 36 refs., 7 figs.

  13. Process Design and Economics for Biochemical Conversion of Lignocellulosic Biomass to Ethanol: Dilute-Acid Pretreatment and Enzymatic Hydrolysis of Corn Stover

    SciTech Connect

    Humbird, D.; Davis, R.; Tao, L.; Kinchin, C.; Hsu, D.; Aden, A.; Schoen, P.; Lukas, J.; Olthof, B.; Worley, M.; Sexton, D.; Dudgeon, D.

    2011-03-01

    This report describes one potential biochemical ethanol conversion process, conceptually based upon core conversion and process integration research at NREL. The overarching process design converts corn stover to ethanol by dilute-acid pretreatment, enzymatic saccharification, and co-fermentation. Building on design reports published in 2002 and 1999, NREL, together with the subcontractor Harris Group Inc., performed a complete review of the process design and economic model for the biomass-to-ethanol process. This update reflects NREL's current vision of the biochemical ethanol process and includes the latest research in the conversion areas (pretreatment, conditioning, saccharification, and fermentation), optimizations in product recovery, and our latest understanding of the ethanol plant's back end (wastewater and utilities). The conceptual design presented here reports ethanol production economics as determined by 2012 conversion targets and 'nth-plant' project costs and financing. For the biorefinery described here, processing 2,205 dry ton/day at 76% theoretical ethanol yield (79 gal/dry ton), the ethanol selling price is $2.15/gal in 2007$.

  14. Hydrolysis of Al3+ from constrained molecular dynamics

    NASA Astrophysics Data System (ADS)

    Ikeda, Takashi; Hirata, Masaru; Kimura, Takaumi

    2006-02-01

    We investigated the hydrolysis reactions of Al3+ in AlCl3 aqueous solution using the constrained molecular dynamics based on the Car-Parrinello molecular-dynamics method. By employing the proton-aluminum coordination number as a reaction coordinate in the constrained molecular dynamics the deprotonation as well as dehydration processes are successfully realized. From our free-energy difference of ΔG0≃8.0kcalmol-1 the hydrolysis constant pKa1 is roughly estimated as 5.8, comparable to the literature value of 5.07. We show that the free-energy difference for the hydrolysis of Al3+ in acidic conditions is at least 4kcalmol-1 higher than that in neutral condition, indicating that the hydrolysis reaction is inhibited by the presence of excess protons located around the hydrated ion, in agreement with the change of the predominant species by pH.

  15. A novel procedure for total nucleic acid extraction from small numbers of Eimeria species oocysts.

    PubMed

    Kaya, Galip; Dale, Colin; Maudlin, Ian; Morgan, Kenton

    2007-01-01

    A series of experiments were performed in an attempt to extract genomic DNA from a small number of Eimerian oocysts. Sonication, ammonia, ethanol and lysozyme were all found to be unsuitable for the digestion of Eimeria oocysts. The chemicals and enzyme given were not capable of either disruption or digestion of oocysts for nucleic acid extraction. They had the capability of penetrating the oocyst wall but could not break-up the oocyst wall. It is impossible to obtain nucleic acid from Eimeria oocysts if the wall is not broken-up. In this study oocyst disruption was achieved using a simple but highly effective treatment regime involving sodium hypochlorite treatment, osmotic shock and proteinase K digestion. Following the disruption of the oocyst walls, a commercially available nucleic acid purification kit (Wizard DNA Purification Kit, Promega) can be used to prepare high quality nucleic acid.

  16. One-Pot Procedure for Recovery of Gallic Acid from Wastewater and Encapsulation within Protein Particles.

    PubMed

    Nourbakhsh, Himan; Madadlou, Ashkan; Emam-Djomeh, Zahra; Wang, Yi-Cheng; Gunasekaran, Sundaram; Mousavi, Mohammad E

    2016-02-24

    A whey protein isolate solution was heat-denatured and treated with the enzyme transglutaminase, which cross-linked ≈26% of the amino groups and increased the magnitude of the ζ-potential value. The protein solution was microemulsified, and then the resulting water-in-oil microemulsion was dispersed within a gallic acid-rich model wastewater. Gallic acid extraction by the outlined microemulsion liquid membrane (MLM) from the exterior aqueous phase (wastewater) and accumulation within the internal aqueous nanodroplets induced protein cold-set gelation and resulted in the formation of gallic acid-enveloping nanoparticles. Measurements with a strain-controlled rheometer indicated a progressive increase in the MLM viscosity during gallic acid recovery corresponding to particle formation. The mean hydrodynamic size of the nanoparticles made from the heat-denatured and preheated enzymatically cross-linked proteins was 137 and 122 nm, respectively. The enzymatic cross-linking of whey proteins led to a higher gallic acid recovery yield and increased the glass transition enthalpy and temperature. A similar impact on glass transition indices was observed by the gallic acid-induced nanoparticulation of proteins. Scanning electron microscopy showed the existence of numerous jammed/fused nanoparticles. It was suggested on the basis of the results of Fourier transform infrared spectroscopy that the in situ nanoparticulation of proteins shifted the C-N stretching and C-H bending peaks to higher wavenumbers. X-ray diffraction results proposed a decreased β-sheet content for proteins because of the acid-induced particulation. The nanoparticles made from the enzymatically cross-linked protein were more stable against the in vitro gastrointestinal digestion and retained almost 19% of the entrapped gallic acid after 300 min sequential gastric and intestinal digestions. PMID:26862880

  17. One-Pot Procedure for Recovery of Gallic Acid from Wastewater and Encapsulation within Protein Particles.

    PubMed

    Nourbakhsh, Himan; Madadlou, Ashkan; Emam-Djomeh, Zahra; Wang, Yi-Cheng; Gunasekaran, Sundaram; Mousavi, Mohammad E

    2016-02-24

    A whey protein isolate solution was heat-denatured and treated with the enzyme transglutaminase, which cross-linked ≈26% of the amino groups and increased the magnitude of the ζ-potential value. The protein solution was microemulsified, and then the resulting water-in-oil microemulsion was dispersed within a gallic acid-rich model wastewater. Gallic acid extraction by the outlined microemulsion liquid membrane (MLM) from the exterior aqueous phase (wastewater) and accumulation within the internal aqueous nanodroplets induced protein cold-set gelation and resulted in the formation of gallic acid-enveloping nanoparticles. Measurements with a strain-controlled rheometer indicated a progressive increase in the MLM viscosity during gallic acid recovery corresponding to particle formation. The mean hydrodynamic size of the nanoparticles made from the heat-denatured and preheated enzymatically cross-linked proteins was 137 and 122 nm, respectively. The enzymatic cross-linking of whey proteins led to a higher gallic acid recovery yield and increased the glass transition enthalpy and temperature. A similar impact on glass transition indices was observed by the gallic acid-induced nanoparticulation of proteins. Scanning electron microscopy showed the existence of numerous jammed/fused nanoparticles. It was suggested on the basis of the results of Fourier transform infrared spectroscopy that the in situ nanoparticulation of proteins shifted the C-N stretching and C-H bending peaks to higher wavenumbers. X-ray diffraction results proposed a decreased β-sheet content for proteins because of the acid-induced particulation. The nanoparticles made from the enzymatically cross-linked protein were more stable against the in vitro gastrointestinal digestion and retained almost 19% of the entrapped gallic acid after 300 min sequential gastric and intestinal digestions.

  18. Instrumentation and automated photometric titration procedure for total acidity determination in red wine employing a multicommuted flow system.

    PubMed

    Garcia, Ausberta Jesus Cabezas; Reis, Boaventura F

    2006-01-01

    An automated procedure for photometric titration of red wine and associated instrumentation is described. The procedure was based on the flow-batch approach implemented employing multicommutation. The photometric detection was carried out using a homemade LED-based photometer. The mixing device, LED, and photodetector were attached to the titration chamber in order to form a compact and small-sized unit. The flow system comprised an automatic injector and three-way solenoid valves, which were controlled by a microcomputer through an electronic interface card. The software, written in Quick BASIC 4.5, was designed with abilities to accomplish all steps of the titration procedure including data acquisition and real-time processing to decide about the course of titration in the following step and so forth, until the titration endpoint was reached. The usefulness of the proposed titration system was demonstrated by analyzing red wine samples. When results were compared with those obtained using the AOAC reference method, no significant difference was observed at the 95% confidence level. A relative standard deviation of ca 2% (n=9) was obtained when processing a typical red wine sample containing 7.3 gl-1 total acidity expressed as tartaric acid.

  19. Instrumentation and automated photometric titration procedure for total acidity determination in red wine employing a multicommuted flow system.

    PubMed

    Garcia, Ausberta Jesus Cabezas; Reis, Boaventura F

    2006-01-01

    An automated procedure for photometric titration of red wine and associated instrumentation is described. The procedure was based on the flow-batch approach implemented employing multicommutation. The photometric detection was carried out using a homemade LED-based photometer. The mixing device, LED, and photodetector were attached to the titration chamber in order to form a compact and small-sized unit. The flow system comprised an automatic injector and three-way solenoid valves, which were controlled by a microcomputer through an electronic interface card. The software, written in Quick BASIC 4.5, was designed with abilities to accomplish all steps of the titration procedure including data acquisition and real-time processing to decide about the course of titration in the following step and so forth, until the titration endpoint was reached. The usefulness of the proposed titration system was demonstrated by analyzing red wine samples. When results were compared with those obtained using the AOAC reference method, no significant difference was observed at the 95% confidence level. A relative standard deviation of ca 2% (n=9) was obtained when processing a typical red wine sample containing 7.3 gl-1 total acidity expressed as tartaric acid. PMID:17671625

  20. Effects of mixing procedure itself on the structure, viscosity, and spreadability of white petrolatum and salicylic acid ointment and the skin permeation of salicylic acid.

    PubMed

    Kitagawa, Shuji; Fujiwara, Megumi; Okinaka, Yuta; Yutani, Reiko; Teraoka, Reiko

    2015-01-01

    White petrolatum is a mixture of solid and liquid hydrocarbons and its structure can be affected by shear stress. Thus, it might also induce changes in its rheological properties. In this study, we used polarization microscopy to investigate how different mixing methods affect the structure of white petrolatum. We used two different mixing methods, mixing using a rotation/revolution mixer and mixing using an ointment slab and an ointment spatula. The extent of the fragmentation and dispersal of the solid portion of white petrolatum depended on the mixing conditions. Next, we examined the changes in the structure of a salicylic acid ointment, in which white petrolatum was used as a base, induced by mixing and found that the salicylic acid solids within the ointment were also dispersed. In addition to these structural changes, the viscosity and thixotropic behavior of both test substances also decreased in a mixing condition-dependent manner. The reductions in these parameters were most marked after mixing with a rotation/revolution mixer, and similar results were obtained for spreadability. We also investigated the effects of mixing procedure on the skin accumulation and permeation of salicylic acid. They were increased by approximately three-fold after mixing. Little difference in skin accumulation or permeation was detected between the two mixing methods. These findings indicate that mixing procedures themselves affect the utility and physiological effects of white petrolatum-based ointments. Therefore, these effects should be considered when mixing is required for the clinical use of petrolatum-based ointments.

  1. Statistical Evaluation of HTS Assays for Enzymatic Hydrolysis of β-Keto Esters

    PubMed Central

    Dold, S. -M.; Zimmermann, S.; Hamacher, K.; Schmitz, K.; Rudat, J.

    2016-01-01

    β-keto esters are used as precursors for the synthesis of β-amino acids, which are building blocks for some classes of pharmaceuticals. Here we describe the comparison of screening procedures for hydrolases to be used for the hydrolysis of β-keto esters, the first step in the preparation of β-amino acids. Two of the tested high throughput screening (HTS) assays depend on coupled enzymatic reactions which detect the alcohol released during ester hydrolysis by luminescence or absorption. The third assay detects the pH shift due to acid formation using an indicator dye. To choose the most efficient approach for screening, we assessed these assays with different statistical methods—namely, the classical Z’-factor, standardized mean difference (SSMD), the Kolmogorov-Smirnov-test, and t-statistics. This revealed that all three assays are suitable for HTS, the pH assay performing best. Based on our data we discuss the explanatory power of different statistical measures. Finally, we successfully employed the pH assay to identify a very fast hydrolase in an enzyme-substrate screening. PMID:26730596

  2. A Rapid and Accurate Extraction Procedure for Analysing Free Amino Acids in Meat Samples by GC-MS

    PubMed Central

    Barroso, Miguel A.; Ruiz, Jorge; Antequera, Teresa

    2015-01-01

    This study evaluated the use of a mixer mill as the homogenization tool for the extraction of free amino acids in meat samples, with the main goal of analyzing a large number of samples in the shortest time and minimizing sample amount and solvent volume. Ground samples (0.2 g) were mixed with 1.5 mL HCl 0.1 M and homogenized in the mixer mill. The final biphasic system was separated by centrifugation. The supernatant was deproteinized, derivatized and analyzed by gas chromatography. This procedure showed a high extracting ability, especially in samples with high free amino acid content (recovery = 88.73–104.94%). It also showed a low limit of detection and quantification (3.8 · 10−4–6.6 · 10−4 μg μL−1 and 1.3 · 10−3–2.2 · 10−2 μg μL−1, resp.) for most amino acids, an adequate precision (2.15–20.15% for run-to-run), and a linear response for all amino acids (R2 = 0.741–0.998) in the range of 1–100 µg mL−1. Moreover, it takes less time and requires lower amount of sample and solvent than conventional techniques. Thus, this is a cost and time efficient tool for homogenizing in the extraction procedure of free amino acids from meat samples, being an adequate option for routine analysis. PMID:25873963

  3. Development of procedures for determining the amino acid requirements of chickens by the indicator amino acid oxidation method.

    PubMed

    Ewing, H P; Pesti, G M; Bakalli, R I

    2001-02-01

    To better understand the amino acid requirements of chickens, a method is needed to determine a point estimate of the requirement. A method developed to determine the amino acid requirements of piglets and human infants by using the oxidation rate of an indicator amino acid as the test parameter was adapted for use in growing chickens. Polycarbonate chambers measuring 30 x 40 x 30 (L x W x H) were constructed to house one small mature chicken or several small immature chickens and to trap exhaled CO2. In the first experiment, 10-d-old chicks (250 to 300 g each) were feed deprived for 12 h and given 1 g of a methionine-deficient diet (gavage) with L-[1-C14]phenylalanine. Peak oxidation of L-[1-C14]phenylalanine occurred between 30 and 90 min (-200 dpm/g). A linear rate of oxidation (slope = -1.84; r2 = 0.96) was achieved by 120 min after feeding until after 180 min, when oxidation stabilized at a low rate. The second experiment tested different chambers and chicks with the same treatment to show repeatability. There were four chicks (250 to 300 g each) in each of three apparently identical chambers. Chicks were given two meals labeled with L-[1-C14]phenylalanine, 2 h apart. The CV for the 0- and 30-min collections were 17 and 10%, respectively. The CV for the remaining collections remained at <4%. These data supported a system of two feedings, 2 h apart to reduce variability and a collection period that included up to 3 h after the second feeding.

  4. Pretreatment and enzymatic hydrolysis of lignocellulosic biomass

    NASA Astrophysics Data System (ADS)

    Corredor, Deisy Y.

    The performance of soybean hulls and forage sorghum as feedstocks for ethanol production was studied. The main goal of this research was to increase fermentable sugars' yield through high-efficiency pretreatment technology. Soybean hulls are a potential feedstock for production of bio-ethanol due to their high carbohydrate content (≈50%) of nearly 37% cellulose. Soybean hulls could be the ideal feedstock for fuel ethanol production, because they are abundant and require no special harvesting and additional transportation costs as they are already in the plant. Dilute acid and modified steam-explosion were used as pretreatment technologies to increase fermentable sugars yields. Effects of reaction time, temperature, acid concentration and type of acid on hydrolysis of hemicellulose in soybean hulls and total sugar yields were studied. Optimum pretreatment parameters and enzymatic hydrolysis conditions for converting soybean hulls into fermentable sugars were identified. The combination of acid (H2SO4, 2% w/v) and steam (140°C, 30 min) efficiently solubilized the hemicellulose, giving a pentose yield of 96%. Sorghum is a tropical grass grown primarily in semiarid and dry parts of the world, especially in areas too dry for corn. The production of sorghum results in about 30 million tons of byproducts mainly composed of cellulose, hemicellulose, and lignin. Forage sorghum such as brown midrib (BMR) sorghum for ethanol production has generated much interest since this trait is characterized genetically by lower lignin concentrations in the plant compared with conventional types. Three varieties of forage sorghum and one variety of regular sorghum were characterized and evaluated as feedstock for fermentable sugar production. Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM) and X-Ray diffraction were used to determine changes in structure and chemical composition of forage sorghum before and after pretreatment and enzymatic hydrolysis

  5. [Rapid and Dynamic Determination Models of Amino Acids and Catechins Concentrations during the Processing Procedures of Keemun Black Tea].

    PubMed

    Ning, Jing-ming; Yan, Ling; Zhang, Zheng-zhu; Wei, Ling-dong; Li, Lu-qing; Fang, Jun-ting; Huang, Cai-wang

    2015-12-01

    Tea is one of the most popular beverages in the world. For the contribution to the taste and healthy functions of tea, amino acids and catechins are important components. Among different kinds of black teas in the world, Keemun black tea has the famous and specific fragrance, "Keemun aroma". During the processing procedure of Keemun black tea, the contents of amino acids and catechins changed greatly, and the differences of these concentrations during processing varied significantly. However, a rapid and dynamic determination method during the processing procedure was not existed up to now. In order to find out a rapid determination method for the contents of amino acids and catechins during the processing procedure of Keemun black tea, the materials of fresh leaves, withered leaves, twisted leaves, fermented leaves, and crude tea (after drying) were selected to acquire their corresponding near infrared spectroscopy and obtain their contents of amino acids and catechins by chemical analysis method. The original spectra data were preprocessed by the Standard Normal Variate Transformation (SNVT) method. And the model of Near Infrared (NIR) spectroscopy with the contents of amino acids and catechins combined with Synergy Interval Partial Least squares (Si-PLS) was established in this study. The correlation coefficients and the cross validation root mean square error are treated as the efficient indexes for evaluating models. The results showed that the optimal prediction model of amino acids by Si-PLS contained 20 spectral intervals combined with 4 subintervals and 9 principal component factors. The correlation coefficient and the root mean square error of the calibration set were 0. 955 8 and 1. 768, respectively; the correlation coefficient and the root mean square error of the prediction set were 0. 949 5 and 2. 16, respectively. And the optimal prediction model of catechins by Si-PLS contained 20 spectral intervals combined with 3 subintervals and 10 principal

  6. ESTIMATION OF PHOSPHATE ESTER HYDROLYSIS RATE CONSTANTS - ALKALINE HYDROLYSIS

    EPA Science Inventory

    SPARC (SPARC Performs Automated Reasoning in Chemistry) chemical reactivity models were extended to allow the calculation of alkaline hydrolysis rate constants of phosphate esters in water. The rate is calculated from the energy difference between the initial and transition state...

  7. ESTIMATION OF PHOSPHATE ESTER HYDROLYSIS RATE CONSTANTS. I. ALKALINE HYDROLYSIS

    EPA Science Inventory

    SPARC (SPARC Performs Automated Reasoning in Chemistry) chemical reactivity models were extended to allow the calculation of alkaline hydrolysis rate constants of phosphate esters in water. The rate is calculated from the energy difference between the initial and transition state...

  8. Paediatric acid-base disorders: A case-based review of procedures and pitfalls.

    PubMed

    Carmody, J Bryan; Norwood, Victoria F

    2013-01-01

    Acid-base disorders occur frequently in paediatric patients. Despite the perception that their analysis is complex and difficult, a straightforward set of rules is sufficient to interpret even the most complex disorders - provided certain pitfalls are avoided. Using a case-based approach, the present article reviews the fundamental concepts of acid-base analysis and highlights common mistakes and oversights. Specific topics include the proper identification of the primary disorder; distinguishing compensatory changes from additional primary disorders; use of the albumin-corrected anion gap to generate a differential diagnosis for patients with metabolic acidosis; screening for mixed disorders with the delta-delta formula; recognizing the limits of compensation; use of the anion gap to identify 'hidden' acidosis; and the importance of using information from the history and physical examination to identify the specific cause of a patient's acid-base disturbance.

  9. Site- and species-specific hydrolysis rates of heroin.

    PubMed

    Szöcs, Levente; Orgován, Gábor; Tóth, Gergő; Kraszni, Márta; Gergó, Lajos; Hosztafi, Sándor; Noszál, Béla

    2016-06-30

    The hydroxide-catalyzed non-enzymatic, simultaneous and consecutive hydrolyses of diacetylmorphine (DAM, heroin) are quantified in terms of 10 site- and species-specific rate constants in connection with also 10 site- and species-specific acid-base equilibrium constants, comprising all the 12 coexisting species in solution. This characterization involves the major and minor decomposition pathways via 6-acetylmorphine and 3-acetylmorphine, respectively, and morphine, the final product. Hydrolysis has been found to be 18-120 times faster at site 3 than at site 6, depending on the status of the amino group and the rest of the molecule. Nitrogen protonation accelerates the hydrolysis 5-6 times at site 3 and slightly less at site 6. Hydrolysis rate constants are interpreted in terms of intramolecular inductive effects and the concomitant local electron densities. Hydrolysis fraction, a new physico-chemical parameter is introduced and determined to quantify the contribution of the individual microspecies to the overall hydrolysis. Hydrolysis fractions are depicted as a function of pH. PMID:27130543

  10. Complex enzyme hydrolysis releases antioxidative phenolics from rice bran.

    PubMed

    Liu, Lei; Wen, Wei; Zhang, Ruifen; Wei, Zhencheng; Deng, Yuanyuan; Xiao, Juan; Zhang, Mingwei

    2017-01-01

    In this study, phenolic profiles and antioxidant activity of rice bran were analyzed following successive treatment by gelatinization, liquefaction and complex enzyme hydrolysis. Compared with gelatinization alone, liquefaction slightly increased the total amount of phenolics and antioxidant activity as measured by ferric reducing antioxidant power (FRAP) and oxygen radical absorbance capacity (ORAC) assays. Complex enzyme hydrolysis significantly increased the total phenolics, flavonoids, FRAP and ORAC by 46.24%, 79.13%, 159.14% and 41.98%, respectively, compared to gelatinization alone. Furthermore, ten individual phenolics present in free or soluble conjugate forms were also analyzed following enzymatic processing. Ferulic acid experienced the largest release, followed by protocatechuic acid and then quercetin. Interestingly, a major proportion of phenolics existed as soluble conjugates, rather than free form. Overall, complex enzyme hydrolysis releases phenolics, thus increasing the antioxidant activity of rice bran extract. This study provides useful information for processing rice bran into functional beverage rich in phenolics. PMID:27507440

  11. Comparative hydrolysis and fermentation of sugarcane and agave bagasse.

    PubMed

    Hernández-Salas, J M; Villa-Ramírez, M S; Veloz-Rendón, J S; Rivera-Hernández, K N; González-César, R A; Plascencia-Espinosa, M A; Trejo-Estrada, S R

    2009-02-01

    Sugarcane and agave bagasse samples were hydrolyzed with either mineral acids (HCl), commercial glucanases or a combined treatment consisting of alkaline delignification followed by enzymatic hydrolysis. Acid hydrolysis of sugar cane bagasse yielded a higher level of reducing sugars (37.21% for depithed bagasse and 35.37% for pith bagasse), when compared to metzal or metzontete (agave pinecone and leaves, 5.02% and 9.91%, respectively). An optimized enzyme formulation was used to process sugar cane bagasse, which contained Celluclast, Novozyme and Viscozyme L. From alkaline-enzymatic hydrolysis of sugarcane bagasse samples, a reduced level of reducing sugar yield was obtained (11-20%) compared to agave bagasse (12-58%). Selected hydrolyzates were fermented with a non-recombinant strain of Saccharomyces cerevisiae. Maximum alcohol yield by fermentation (32.6%) was obtained from the hydrolyzate of sugarcane depithed bagasse. Hydrolyzed agave waste residues provide an increased glucose decreased xylose product useful for biotechnological conversion.

  12. Muscarinic receptor activation of phosphatidylcholine hydrolysis. Relationship to phosphoinositide hydrolysis and diacylglycerol metabolism

    SciTech Connect

    Martinson, E.A.; Goldstein, D.; Brown, J.H. )

    1989-09-05

    We examined the relationship between phosphatidylcholine (PC) hydrolysis, phosphoinositide hydrolysis, and diacylglycerol (DAG) formation in response to muscarinic acetylcholine receptor (mAChR) stimulation in 1321N1 astrocytoma cells. Carbachol increases the release of (3H)choline and (3H)phosphorylcholine ((3H)Pchol) from cells containing (3H)choline-labeled PC. The production of Pchol is rapid and transient, while choline production continues for at least 30 min. mAChR-stimulated release of Pchol is reduced in cells that have been depleted of intracellular Ca2+ stores by ionomycin pretreatment, whereas choline release is unaffected by this pretreatment. Phorbol 12-myristate 13-acetate (PMA) increases the release of choline, but not Pchol, from 1321N1 cells, and down-regulation of protein kinase C blocks the ability of carbachol to stimulate choline production. Taken together, these results suggest that Ca2+ mobilization is involved in mAChR-mediated hydrolysis of PC by a phospholipase C, whereas protein kinase C activation is required for mAChR-stimulated hydrolysis of PC by a phospholipase D. Both carbachol and PMA rapidly increase the formation of (3H)phosphatidic acid ((3H)PA) in cells containing (3H)myristate-labeled PC. (3H)Diacylglycerol ((3H)DAG) levels increase more slowly, suggesting that the predominant pathway for PC hydrolysis is via phospholipase D. When cells are labeled with (3H)myristate and (14C)arachidonate such that there is a much greater 3H/14C ratio in PC compared with the phosphoinositides, the 3H/14C ratio in DAG and PA increases with PMA treatment but decreases in response to carbachol.

  13. Recovery and reuse of cellulase catalyst in an exzymatic cellulose hydrolysis process

    DOEpatents

    Woodward, Jonathan

    1989-01-01

    A process for recovering cellulase from the hydrolysis of cellulose, and reusing it in subsequent hydrolyois procedures. The process utilizes a commercial adsorbent that efficiently removes cellulase from reaction products which can be easily removed by simple decantation.

  14. A simple purification procedure of D-amino-acid oxidase from Candida guilliermondii H(see symbol)-4.

    PubMed

    Gevorgyan, G K; Davtyan, M A; Hambardzumyan, A A

    2012-01-01

    D-amino-acid oxidase (EC 1.4.3.3) was purified about 1480-fold from the yeast Candida guilliermondii H(see symbol)-4 using chromatofocusing method. The purification procedure gave an enzyme preparation which is greater than 90% homogenous on SDS-polyacrylamide gels with a specific activity of 11.54 U/mg at 30 degrees C with D-proline as substrate with the yield of total activity 9.3%. The molecular weights of subunit and native enzyme were determined to be 38.4 and 78.6 kDa by SDS-polyacrylamide gel electrophoresis and gel-filtration, respectively, suggesting that the native enzyme exists as a homodimer. A single molecular form with an isoelectric point of 6.85 was detected in analytical isoelectrofocusing. The optimum pH and temperature were 8.0 and 33 degrees C. An enzyme shows stability in the pH range from 7.4 to 9.0 and at the temperature no higher than 38 degrees C. Activation energy for D-amino-acid oxidase reaction was calculated to be 60 kJ/mol at 30 degrees C. The strict D-isomer specificity of the enzyme is confirmed, since no reaction could be detected with L-amino acids, and a large number of D-amino acids could be substrates for this enzyme. K(m) and V(max) values were determined for D-proline and D-alanine, which, among 22 tested, were the best substrates of the enzyme. D-amino-acid oxidase from the yeast C. guilliermondii is a flavoprotein oxidase in which the prosthetic group is tightly, but not covalently, bound FAD. The enzyme is completely inhibited by sodium benzoate, SH-oxidizing agents, but not by sodium azide, toluene or chloroform. PMID:23156699

  15. Advances in identification of plant gums in cultural heritage by thermally assisted hydrolysis and methylation.

    PubMed

    Riedo, Chiara; Scalarone, Dominique; Chiantore, Oscar

    2010-02-01

    Plant gums are present in works of art as binding media for watercolours and adhesives for cellulosic substrates. Thermally assisted hydrolysis and methylation (THM) in combination with analytical pyrolysis coupled to GC/MS has been applied to the characterisation of plant gums typically used in artworks. THM products from standard samples of arabic gum, tragacanth gum and cherry gum were characterised. The main products identified are permethylated and partially methylated aldonic acids, characteristic of specific epimeric sugars. Aldonic acids were formed by alkaline hydrolysis of free reducing sugars and of reducing polysaccharide terminal groups, while methylation occurs during pyrolysis. The presence of these characteristic markers allows gum identification. A systematic analysis of all the parameters that can affect the marker yields was performed. In particular, the influence of pyrolysis temperature, reagent concentration and contact time between tetramethylammonium hydroxide and sample were studied, and different kinds of sample preparation procedures were tested. Some analyses on real watercolours were performed, and gum binders were classified using the peak area ratio of the main monosaccharide markers.

  16. Multiresponse optimization of an extraction procedure of carnosol and rosmarinic and carnosic acids from rosemary.

    PubMed

    Oliveira, Gerlon de A R; de Oliveira, Anselmo E; da Conceição, Edemílson C; Leles, Maria I G

    2016-11-15

    A green solvent-based optimization for rosmarinic acid (RA), carnosol (COH), and carnosic acid (CA) extraction, the three main antioxidants from rosemary, was performed. The conventional solid-liquid extraction was optimized using a central composite design (CCD) followed by the desirability approach. In the CCD analysis the quantitative effects of extraction time (4.8-55.2min), liquid-to-solid ratio (4.6-21.4mLg(-1)), and ethanol content (44.8-95.2% v/v) were determined for the extracted amount of antioxidants, their concentrations in the extract, and the extraction yield. Samples were analyzed by HPLC and the antioxidants were identified by comparison with pure standard retention times and UV spectra. The desirability function that simultaneously maximizes the antioxidants extraction and their concentrations in the final product was validated. The extraction using a hydroalcoholic solution 70% v/v, at low liquid-to-solid ratio (5mLg(-1)), and after 55-min yielded an antioxidant recovery rate of 89.8%, and a final product 4.75 times richer in the main antioxidants than the raw material.

  17. A review of the calculation procedure for critical acid loads for terrestrial ecosystems.

    PubMed

    van der Salm, C; de Vries, W

    2001-04-23

    Target loads for acid deposition in the Netherlands, as formulated in the Dutch environmental policy plan, are based on critical load calculations at the end of the 1980s. Since then knowledge on the effect of acid deposition on terrestrial ecosystems has substantially increased. In the early 1990s a simple mass balance model was developed to calculate critical loads. This model was evaluated and the methods were adapted to represent the current knowledge. The main changes in the model are the use of actual empirical relationships between Al and H concentrations in the soil solution, the addition of a constant base saturation as a second criterion for soil quality and the use of tree species-dependant critical Al/base cation (BC) ratios for Dutch circumstances. The changes in the model parameterisation and in the Al/BC criteria led to considerably (50%) higher critical loads for root damage. The addition of a second criterion in the critical load calculations for soil quality caused a decrease in the critical loads for soils with a median to high base saturation such as loess and clay soils. The adaptation hardly effected the median critical load for soil quality in the Netherlands, since only 15% of the Dutch forests occur on these soils. On a regional scale, however, critical loads were (much) lower in areas where those soils are located.

  18. Multiresponse optimization of an extraction procedure of carnosol and rosmarinic and carnosic acids from rosemary.

    PubMed

    Oliveira, Gerlon de A R; de Oliveira, Anselmo E; da Conceição, Edemílson C; Leles, Maria I G

    2016-11-15

    A green solvent-based optimization for rosmarinic acid (RA), carnosol (COH), and carnosic acid (CA) extraction, the three main antioxidants from rosemary, was performed. The conventional solid-liquid extraction was optimized using a central composite design (CCD) followed by the desirability approach. In the CCD analysis the quantitative effects of extraction time (4.8-55.2min), liquid-to-solid ratio (4.6-21.4mLg(-1)), and ethanol content (44.8-95.2% v/v) were determined for the extracted amount of antioxidants, their concentrations in the extract, and the extraction yield. Samples were analyzed by HPLC and the antioxidants were identified by comparison with pure standard retention times and UV spectra. The desirability function that simultaneously maximizes the antioxidants extraction and their concentrations in the final product was validated. The extraction using a hydroalcoholic solution 70% v/v, at low liquid-to-solid ratio (5mLg(-1)), and after 55-min yielded an antioxidant recovery rate of 89.8%, and a final product 4.75 times richer in the main antioxidants than the raw material. PMID:27283656

  19. The Preparation and Enzymatic Hydrolysis of a Library of Esters

    ERIC Educational Resources Information Center

    Sanford, Elizabeth M.; Smith, Traci L.

    2008-01-01

    An investigative case study involving the preparation of a library of esters using Fischer esterification and alcoholysis of acid chlorides and their subsequent enzymatic hydrolysis by pig liver esterase and orange peel esterase is described. Students work collaboratively to prepare and characterize the library of esters and complete and evaluate…

  20. DFT STUDY OF THE HYDROLYSIS OF SOME S-TRIAZINES

    EPA Science Inventory

    The acid-catalyzed hydrolysis of atrazine and related 2-chloro-s-triazines to the corresponding 2-hydroxy-s-triazines was investigated using the B3LYP hybrid density functional theory method. Gas-phase calculations were performed at the B3LYP/6-311++G(d,p)//B3LYP/6-31G* level of ...

  1. Fuzzy logic feedback control for fed-batch enzymatic hydrolysis of lignocellulosic biomass.

    PubMed

    Tai, Chao; Voltan, Diego S; Keshwani, Deepak R; Meyer, George E; Kuhar, Pankaj S

    2016-06-01

    A fuzzy logic feedback control system was developed for process monitoring and feeding control in fed-batch enzymatic hydrolysis of a lignocellulosic biomass, dilute acid-pretreated corn stover. Digested glucose from hydrolysis reaction was assigned as input while doser feeding time and speed of pretreated biomass were responses from fuzzy logic control system. Membership functions for these three variables and rule-base were created based on batch hydrolysis data. The system response was first tested in LabVIEW environment then the performance was evaluated through real-time hydrolysis reaction. The feeding operations were determined timely by fuzzy logic control system and efficient responses were shown to plateau phases during hydrolysis. Feeding of proper amount of cellulose and maintaining solids content was well balanced. Fuzzy logic proved to be a robust and effective online feeding control tool for fed-batch enzymatic hydrolysis. PMID:26915095

  2. Fuzzy logic feedback control for fed-batch enzymatic hydrolysis of lignocellulosic biomass.

    PubMed

    Tai, Chao; Voltan, Diego S; Keshwani, Deepak R; Meyer, George E; Kuhar, Pankaj S

    2016-06-01

    A fuzzy logic feedback control system was developed for process monitoring and feeding control in fed-batch enzymatic hydrolysis of a lignocellulosic biomass, dilute acid-pretreated corn stover. Digested glucose from hydrolysis reaction was assigned as input while doser feeding time and speed of pretreated biomass were responses from fuzzy logic control system. Membership functions for these three variables and rule-base were created based on batch hydrolysis data. The system response was first tested in LabVIEW environment then the performance was evaluated through real-time hydrolysis reaction. The feeding operations were determined timely by fuzzy logic control system and efficient responses were shown to plateau phases during hydrolysis. Feeding of proper amount of cellulose and maintaining solids content was well balanced. Fuzzy logic proved to be a robust and effective online feeding control tool for fed-batch enzymatic hydrolysis.

  3. Synthesis of nucleic acid probes on membrane supports: a procedure for the removal of unincorporated precursors.

    PubMed

    Bhat, S P

    1990-01-01

    We have used DNA bound to small pieces of nylon membrane for the synthesis of radioactive probes. The DNA to be used for generating the probe(s) is first bound to nylon membranes and then introduced into the reaction mix. The labeling reaction takes place on the membrane and therefore allows easy removal of unincorporated precursors by simple washing for 1-2 min. The clean labeled probe is eluted from the membrane in formamide or in water and is ready for use. This DNA-membrane can be stored for reuse. Synthesis of probes on a solid support such as nylon membrane thus circumvents problems associated with chromatographic manipulations needed for the separation of labeled DNA from unicorporated precursors. Probes synthesized in this manner are as efficient in detecting nucleic acid sequences as those synthesized in solution. PMID:2321760

  4. A screening procedure for identifying acid-sensitive lakes from catchment characteristics.

    PubMed

    Berg, N H; Gallegos, A; Dell, T; Frazier, J; Procter, T; Sickman, J; Grant, S; Blett, T; Arbaugh, M

    2005-06-01

    Monitoring of Wilderness lakes for potential acidification requires information on lake sensitivity to acidification. Catchment properties can be used to estimate the acid neutralizing capacity (ANC) of lakes. Conceptual and general linear models were developed to predict the ANC of lakes in high-elevation (> or = 2170 m) Wilderness Areas in California's Sierra Nevada mountains. Catchment-to-lake area ratio, lake perimeter-to-area ratio, bedrock lithology, vegetation cover, and lake headwater location are significant variables explaining ANC. The general linear models were validated against independently collected water chemistry data and were used as part of a first stage screen to identify Wilderness lakes with low ANC. Expanded monitoring of atmospheric deposition is essential for improving the predictability of lake ANC.

  5. Enzymatic Hydrolysis of Cellulosic Biomass

    SciTech Connect

    Yang, Bin; Dai, Ziyu; Ding, Shi-You; Wyman, Charles E.

    2011-08-22

    Biological conversion of cellulosic biomass to fuels and chemicals offers the high yields to products vital to economic success and the potential for very low costs. Enzymatic hydrolysis that converts lignocellulosic biomass to fermentable sugars may be the most complex step in this process due to substrate-related and enzyme-related effects and their interactions. Although enzymatic hydrolysis offers the potential for higher yields, higher selectivity, lower energy costs, and milder operating conditions than chemical processes, the mechanism of enzymatic hydrolysis and the relationship between the substrate structure and function of various glycosyl hydrolase components are not well understood. Consequently, limited success has been realized in maximizing sugar yields at very low cost. This review highlights literature on the impact of key substrate and enzyme features that influence performance to better understand fundamental strategies to advance enzymatic hydrolysis of cellulosic biomass for biological conversion to fuels and chemicals. Topics are summarized from a practical point of view including characteristics of cellulose (e.g., crystallinity, degree of polymerization, and accessible surface area) and soluble and insoluble biomass components (e.g., oligomeric xylan, lignin, etc.) released in pretreatment, and their effects on the effectiveness of enzymatic hydrolysis. We further discuss the diversity, stability, and activity of individual enzymes and their synergistic effects in deconstructing complex lignocellulosic biomass. Advanced technologies to discover and characterize novel enzymes and to improve enzyme characteristics by mutagenesis, post-translational modification, and over-expression of selected enzymes and modifications in lignocellulosic biomass are also discussed.

  6. Comparison of an automated nucleic acid extraction system with the column-based procedure

    PubMed Central

    Hinz, Rebecca; Hagen, Ralf Matthias

    2015-01-01

    Here, we assessed the extraction efficiency of a deployable bench-top nucleic acid extractor EZ1 in comparison to the column-based approach with complex sample matrices. A total of 48 EDTA blood samples and 81 stool samples were extracted by EZ1 automated extraction and the column-based QIAamp DNA Mini Kit. Blood sample extractions were assessed by two real-time malaria PCRs, while stool samples were analyzed by six multiplex real-time PCR assays targeting bacterial, viral, and parasitic stool pathogens. Inhibition control PCR testing was performed as well. In total, 147 concordant and 13 discordant pathogen-specific PCR results were obtained. The latter comprised 11 positive results after column-based extraction only and two positive results after EZ1 extraction only. EZ1 extraction showed a higher frequency of inhibition. This phenomenon was, however, inconsistent for the different PCR schemes. In case of concordant PCR results, relevant differences of cycle threshold numbers for the compared extraction schemes were not observed. Switches from well-established column-based extraction to extraction with the automated EZ1 system do not lead to a relevantly reduced yield of target DNA when complex sample matrices are used. If sample inhibition is observed, column-based extraction from another sample aliquot may be considered. PMID:25883797

  7. Enhancing adsorption efficiency of dichloroacetic acid onto mesoporous carbons: Procedure optimization, mechanism and characterization.

    PubMed

    Ding, Ying; Zhu, Jianzhong; Ji, Dongliang; Cao, Yang; Ling, Xiaojia; Chen, Wei

    2015-08-15

    Highly ordered mesoporous carbon may be directly synthesized via supramolecular self-assembly with in situ evaporation-induced crystallization process by controlling thermal reaction temperatures and carbon mass loading. In the present study, the effects of thermal reaction temperatures on the structural characterization and adsorption capacity of mesoporous carbon have been investigated and analyzed with orthogonal test experiments. The results show the carbonization temperature (R=32.1) plays a more important role than the self-assembly temperature (R=8.5) and thermal polymerization temperature (R=10.1) in manipulating the pore texture structures. The optimization grouping temperature was 40-110-500 °C. The optimum mesoporous carbon sample had the highest BET specific surface area (474 m(2)/g), the largest pore volume (0.46 cm(3)/g), and with reasonable uniform pore size distribution. The adsorption evaluation also shows the adsorption capacity is strongly correlated with the pore structure of mesoporous carbon, the optimized mesoporous carbon sample displayed the largest adsorption capacity (350 mg/g) at an initial concentration of 20.0 mg/L of dichloroacetic acid. The study results indicate optimization of thermal reaction parameters is an effective approach for synthesis of ordered mesoporous carbons.

  8. Hydrolysis of green tea residue protein using proteolytic enzyme derived from Aspergillus oryzae.

    PubMed

    Xu, Yong-Quan; Zhong, Xiao-Yu; Chen, Su-Qin; Yin, Jun-Feng

    2013-02-01

    Free amino acids are important chemical components which impact the taste of green tea infusion. The hydrolysis of water-insoluble protein in the green tea residue helps to increase the contents of free amino acids components except theanine. Studies indicate that the hydrolysis of the tea protein could be restricted due to interaction of polyphenols with protein. The experiment indicates that the hydrolysis of tea protein by protease is the main trend when the polyphenols concentration is lower than 5 mg ml(-1), however, the proteins (including tea protein and protease) would interact with polyphenoles instead of hydrolysis when the concentration of polyphenols is higher than 5 mg ml(-1). The hydrolysis of tea protein is absolutely restrained when concentration comes to 10 mg ml(-1). PMID:24425904

  9. Procedures for safe handling of off-gases from electric vehicle lead-acid batteries during overcharge

    SciTech Connect

    LaBelle, S.J.; Bhattacharyya, M.H.; Loutfy, R.O.; Varma, R.

    1980-01-25

    The potential for generation of toxic gases from lead-acid batteries has long been recognized. Prior to the current interest in electric vehicles, there were no studies specificaly oriented to toxic gas release from traction batteries, however. As the Department of Energy Demonstration Project (in the Electric and Hybrid Vehicle Program) progresses, available data from past studies and parallel health effects programs must be digested into guidance to the drivers and maintenance personnel, tailored to their contact with electric vehicles. The basic aspects of lead-acid battery operation, vehicle use, and health effects of stibine and arsine to provide electric vehicle users with the information behind the judgment that vehicle operation and testing may proceed are presented. Specifically, it is concluded that stibine generation or arsine generation at rapid enough rates to induce acute toxic response is not at all likely. Procedures to guard against low-level exposure until more definitive data on ambient concentrations of the gases are collected are presented for both charging the batteries and driving the vehicles. A research plan to collect additional quantitative data from electric traction batteries is presented.

  10. STUDIES ON THE BACTERIOPHAGE OF D'HERELLE : IX. EVIDENCE OF HYDROLYSIS OF BACTERIAL PROTEIN DURING LYSIS.

    PubMed

    Hetler, D M; Bronfenbrenner, J

    1928-07-31

    1. During the process of lysis by bacteriophage, there is an appreciable increase in the amount of free amino acid present in the culture. 2. The increase of free amino acid is due to hydrolysis of bacterial protein.

  11. Enzymatic hydrolysis of cellulose and various pretreated wood fractions

    SciTech Connect

    Saddler, J.N.; Brownell, H.H.; Clermont, L.P.; Levitin, N.

    1982-06-01

    Three strains of Trichoderma-Trichoderma reesei C30, Trichoderma reesei QM9414, and Trichoderma species E58-were used to study the enzymatic hydrolysis of pretreated wood substrates. Each of the culture filtrates was incubated with a variety of commercially prepared cellulose substrates and pretreated wood substrates. Solka floc was the most easily degraded commercial cellulose. The enzyme accessibility of steam-exploded samples which has been alkali extracted and then stored wet decreased with the duration of the steam treatment. Air drying reduced the extent of hydrolysis of all the samples but had a greater effect on the samples which had previously shown the greatest hydrolysis. Mild pulping using 2% chlorite increased the enzymatic hydrolysis of all the samples. Steam explosion was shown to be an excellent pretreatment method for aspen wood and was much superior to dilute nitric acid pretreatment. The results indicate that the distribution of the lignin as well as the surface area of the cellulosic substrate are important features in enzymatic hydrolysis. (Refs 17).

  12. Enzymatic hydrolysis of fractionated products from oil thermally oxidated

    SciTech Connect

    Yashida, H.; Alexander, J.C.

    1983-01-01

    Enzymatic hydrolysis of the acylglycerol products obtained from thermally oxidized vegetable oils was studied. Corn, sunflower and soybean oils were heated in the laboratory at 180/sup 0/C for 50, 70 and 100 hr with aeration and directly fractionated by silicic acid column chromatography. By successive elution with 20%, then 60% isopropyl ether in n-hexane, and diethyl ether, the thermally oxidized oils were separated into three fractions: the nonpolar fraction (monomeric compounds), slightly polar fraction (dimeric compounds), and polar fraction comprising oligomeric compounds. Enzymatic hydrolysis with pancreatic lipase showed that the monomers were hydrolyzed as rapidly as the corresponding unheated oils, the dimers much more slowly, and the oligomeric compounds barely at all. Overall, the hydrolysis of the dimers was less than 23% of that for the monomers, with small differences among the oils. Longer heating periods resulted in greater reductions in hydrolysis of the dimeric compounds. These results suggest that the degree of enzymatic hydrolysis of the fractionated acylglycerol compounds is related to differences in the thermal oxidative deterioration, and amounts of polar compounds in the products. (33 Refs.)

  13. Rapid isolation procedure for Δ9-tetrahydrocannabinolic acid A (THCA) from Cannabis sativa using two flash chromatography systems.

    PubMed

    Wohlfarth, Ariane; Mahler, Hellmut; Auwärter, Volker

    2011-10-15

    Two isolation procedures for Δ9-tetrahydrocannabinolic acid A (THCA), the biogenetic precursor in the biosynthesis of the psychoactive Δ9-tetrahydrocannabinol (THC) in the cannabis plant, are presented. Two flash chromatography systems that can be used independently from each other were developed to separate THCA from other compounds of a crude cannabis extract. In both systems UV absorption at 209 and 270 nm was monitored. Purity was finally determined by HPLC-DAD, NMR and GC-MS analysis with a focus on the impurity THC. System 1 consisted of a normal phase silica column (120 g) as well as cyclohexane and acetone--both spiked with the modifier pyridine--as mobile phases. Gradient elution was performed over 15 min. After the chromatographic run the fractions containing THCA fractions were pooled, extracted with hydrochloric acid to eliminate pyridine and evaporated to dryness. Loading 1800 mg cannabis extract yielded 623 mg THCA with a purity of 99.8% and a THC concentration of 0.09%. System 2 was based on a reversed-phase C18 column (150 g) combined with 0.55% formic acid and methanol as mobile phases. A very flat gradient was set over 20 minutes. After pooling the THCA-containing fractions methanol was removed in a rotary evaporator. THCA was re-extracted from the remaining aqueous phase with methyl tert-butyl ether. The organic phase was finally evaporated under high vacuum conditions. Loading 300 mg cannabis extract yielded 51 mg THCA with a purity of 98.8% and a THC concentration of 0.67%.

  14. Hepatic triacylglycerol hydrolysis regulates peroxisome proliferator-activated receptor alpha activity.

    PubMed

    Sapiro, Jessica M; Mashek, Mara T; Greenberg, Andrew S; Mashek, Douglas G

    2009-08-01

    Recent evidence suggests that fatty acids generated from intracellular triacylglycerol (TAG) hydrolysis may have important roles in intracellular signaling. This study was conducted to determine if fatty acids liberated from TAG hydrolysis regulate peroxisome proliferator-activated receptor alpha (PPARalpha). Primary rat hepatocyte cultures were treated with adenoviruses overexpressing adipose differentiation-related protein (ADRP) or adipose triacylglycerol lipase (ATGL) or treated with short interfering RNA (siRNA) targeted against ADRP. Subsequent effects on TAG metabolism and PPARalpha activity and target gene expression were determined. Overexpressing ADRP attenuated TAG hydrolysis, whereas siRNA-mediated knockdown of ADRP or ATGL overexpression resulted in enhanced TAG hydrolysis. Results from PPARalpha reporter activity assays demonstrated that decreasing TAG hydrolysis by ADRP overexpression resulted in a 35-60% reduction in reporter activity under basal conditions or in the presence of fatty acids. As expected, PPARalpha target genes were also decreased in response to ADRP overexpression. However, the PPARalpha ligand, WY-14643, was able to restore PPARalpha activity following ADRP overexpression. Despite its effects on PPARalpha, overexpressing ADRP did not affect PPARgamma activity. Enhancing TAG hydrolysis through ADRP knockdown or ATGL overexpression increased PPARalpha activity. These results indicate that TAG hydrolysis and the consequential release of fatty acids regulate PPARalpha activity.

  15. Fungal cellulase/xylanase production and corresponding hydrolysis using pretreated corn stover as substrates.

    PubMed

    Zhang, Liang; Wang, Xiaoqing; Ruan, Zhenhua; Liu, Ying; Niu, Xiaorui; Yue, Zhengbo; Li, Zhimin; Liao, Wei; Liu, Yan

    2014-01-01

    Three pretreated corn stover (ammonia fiber expansion, dilute acid, and dilute alkali) were used as carbon source to culture Trichoderma reesei Rut C-30 for cellulase and xylanase production. The results indicated that the cultures on ammonia fiber expansion and alkali pretreated corn stover had better enzyme production than the acid pretreated ones. The consequent enzymatic hydrolysis was performed applying fungal enzymes on pretreated corn stover samples. Tukey's statistical comparisons exhibited that there were significant differences on enzymatic hydrolysis among different combination of fungal enzymes and pretreated corn stover. The higher sugar yields were achieved by the enzymatic hydrolysis of dilute alkali pretreated corn stover.

  16. The effect of extracellular polysaccharides on the goethite-surface promoted hydrolysis of organophosphates.

    NASA Astrophysics Data System (ADS)

    Kenney, J. P. L.; Olsson, R.; Giesler, R.; Persson, P.

    2012-04-01

    found to be rapid, and the subsequent hydrolysis was found to be dependent upon pH and the properties of the mineral-water interface. When enzyme was added to the goethite-monoester system, at the optimum conditions for the acid phosphatase enzyme, the rate of hydrolysis reached nearly the same rate as the enzymatic hydrolysis of the monoester in a goethite-free system. Thus, the enzyme can change the system from one with no hydrolysis to one with significant hydrolysis. The presence of alginate in the goethite-monoester-enzyme system changes the properties of the interface, thereby changing the hydrolysis of these phosphate monoesters.

  17. Switching Catalysis from Hydrolysis to Perhydrolysis in Pseudomonas fluorescens Esterase

    SciTech Connect

    Yin, D.; Bernhardt, P; Morley, K; Jiang, Y; Cheeseman, J; Purpero, V; Schrag, J; Kazlauskas, R

    2010-01-01

    Many serine hydrolases catalyze perhydrolysis, the reversible formation of peracids from carboxylic acids and hydrogen peroxide. Recently, we showed that a single amino acid substitution in the alcohol binding pocket, L29P, in Pseudomonas fluorescens (SIK WI) aryl esterase (PFE) increased the specificity constant of PFE for peracetic acid formation >100-fold [Bernhardt et al. (2005) Angew. Chem., Int. Ed. 44, 2742]. In this paper, we extend this work to address the three following questions. First, what is the molecular basis of the increase in perhydrolysis activity? We previously proposed that the L29P substitution creates a hydrogen bond between the enzyme and hydrogen peroxide in the transition state. Here we report two X-ray structures of L29P PFE that support this proposal. Both structures show a main chain carbonyl oxygen closer to the active site serine as expected. One structure further shows acetate in the active site in an orientation consistent with reaction by an acyl-enzyme mechanism. We also detected an acyl-enzyme intermediate in the hydrolysis of {var_epsilon}-caprolactone by mass spectrometry. Second, can we further increase perhydrolysis activity? We discovered that the reverse reaction, hydrolysis of peracetic acid to acetic acid and hydrogen peroxide, occurs at nearly the diffusion limited rate. Since the reverse reaction cannot increase further, neither can the forward reaction. Consistent with this prediction, two variants with additional amino acid substitutions showed 2-fold higher k{sub cat}, but K{sub m} also increased so the specificity constant, k{sub cat}/K{sub m}, remained similar. Third, how does the L29P substitution change the esterase activity? Ester hydrolysis decreased for most esters (75-fold for ethyl acetate) but not for methyl esters. In contrast, L29P PFE catalyzed hydrolysis of {var_epsilon}-caprolactone five times more efficiently than wild-type PFE. Molecular modeling suggests that moving the carbonyl group closer to the

  18. Mechanism and applicability of hydrolysis of peptides and proteins utilizing Pt(II) complexes

    SciTech Connect

    Burgeson, I.E.

    1990-06-13

    The hydrolysis of amino acid esters and amides has been achieved by using organic reagents, strongly acidic and basic solutions, and transition metal complexes. However, enzymes have always been able to surpass these methods in terms of speed of the hydrolysis and the mild conditions necessary to observe hydrolysis. In order to understand how enzymes undergo their reactions with such remarkable speed and efficiency, researchers are studying and developing inorganic reagents which can facilitate the hydrolysis of peptide bonds. The treatment of the tripetide {gamma}-glutamyl-cyteinylglycine with one equivalent of PtCl{sub 4}{sup {minus}2} results in hydrolysis of the cysteinyl-glycine bond. The reaction is strongly dependent on the amount of chloride ion in solution and also shows a lesser dependence on ionic strength and pH. Hydrolysis is promoted through a chelate interaction of the platinum with the sulfur of cysteine and the carbonyl oxygen of the amide bond. The hydrolysis of proteins was then undertaken. Yeast cytochrome c and the subunits of hemoglobin were examined to determine if PtCl{sub 4}{sup {minus}2} or Pt(en)Cl{sub 2} could promote cleavage of the peptide bond next to a cysteine residue. It appears that hydrolysis of the peptide bond to the right of the cysteinly side chain has been realized. 51 refs., 12 figs., 12 tabs.

  19. Lipase applications in oil hydrolysis with a case study on castor oil: a review.

    PubMed

    Goswami, Debajyoti; Basu, Jayanta Kumar; De, Sirshendu

    2013-03-01

    Lipase (triacylglycerol acylhydrolase) is a unique enzyme which can catalyze various types of reactions such as hydrolysis, esterification, alcoholysis etc. In particular, hydrolysis of vegetable oil with lipase as a catalyst is widely studied. Free lipase, lipase immobilized on suitable support, lipase encapsulated in a reverse micelle and lipase immobilized on a suitable membrane to be used in membrane reactor are the most common ways of employing lipase in oil hydrolysis. Castor oil is a unique vegetable oil as it contains high amounts (90%) of a hydroxy monounsaturated fatty acid named ricinoleic acid. This industrially important acid can be obtained by hydrolysis of castor oil. Different conventional hydrolysis processes have certain disadvantages which can be avoided by a lipase-catalyzed process. The degree of hydrolysis varies widely for different lipases depending on the operating range of process variables such as temperature, pH and enzyme loading. Immobilization of lipase on a suitable support can enhance hydrolysis by suppressing thermal inactivation and estolide formation. The presence of metal ions also affects lipase-catalyzed hydrolysis of castor oil. Even a particular ion has different effects on the activity of different lipases. Hydrophobic organic solvents perform better than hydrophilic solvents during the reaction. Sonication considerably increases hydrolysis in case of lipolase. The effects of additives on the same lipase vary with their types. Nonionic surfactants enhance hydrolysis whereas cationic and anionic surfactants decrease it. A single variable optimization method is used to obtain optimum conditions. In order to eliminate its disadvantages, a statistical optimization method is used in recent studies. Statistical optimization shows that interactions between any two of the following pH, enzyme concentration and buffer concentration become significant in presence of a nonionic surfactant named Span 80.

  20. Screening procedure for detection of non-steroidal anti-inflammatory drugs and their metabolites in urine as part of a systematic toxicological analysis procedure for acidic drugs and poisons by gas chromatography-mass spectrometry after extractive methylation.

    PubMed

    Maurer, H H; Tauvel, F X; Kraemer, T

    2001-01-01

    Non-steroidal anti-inflammatory drugs (NSAIDs) are widely used as analgesic and anti-rheumatic drugs, and they are often misused. A gas chromatographic-mass spectrometric (GC-MS) screening procedure was developed for their detection in urine as part of a systematic toxicological analysis procedure for acidic drugs and poisons after extractive methylation. The compounds were separated by capillary GC and identified by computerized MS in the full-scan mode. Using mass chromatography with the ions m/z 119, 135, 139, 152, 165, 229, 244, 266, 272, and 326, the possible presence of NSAIDs and their metabolites could be indicated. The identity of positive signals in such mass chromatograms was confirmed by comparison of the peaks underlying full mass spectra with the reference spectra recorded during this study. This method allowed the detection of therapeutic concentrations of acemetacin, acetaminophen (paracetamol), acetylsalicylic acid, diclofenac, diflunisal, etodolac, fenbufen, fenoprofen, flufenamic acid, flurbiprofen, ibuprofen, indometacin, kebuzone, ketoprofen, lonazolac, meclofenamic acid, mefenamic acid, mofebutazone, naproxen, niflumic acid, phenylbutazone, suxibuzone, tiaprofenic acid, tolfenamic acid, and tolmetin in urine samples. The overall recoveries of the different NSAIDs ranged between 50 and 80% with coefficients of variation of less than 15% (n = 5), and the limits of detection of the different NSAIDs were between 10 and 50 ng/mL (S/N = 3) in the full-scan mode. Extractive methylation has proved to be a versatile method for STA of various acidic drugs, poisons, and their metabolites in urine. It has also successfully been used for plasma analysis.

  1. Small peptides hydrolysis in dry-cured meats.

    PubMed

    Mora, Leticia; Gallego, Marta; Escudero, Elizabeth; Reig, Milagro; Aristoy, M-Concepción; Toldrá, Fidel

    2015-11-01

    Large amounts of different peptides are naturally generated in dry-cured meats as a consequence of the intense proteolysis mechanisms which take place during their processing. In fact, meat proteins are extensively hydrolysed by muscle endo-peptidases (mainly calpains and cathepsins) followed by exo-peptidases (mainly, tri- and di-peptidyl peptidases, dipeptidases, aminopeptidases and carboxypeptidases). The result is a large amount of released free amino acids and a pool of numerous peptides with different sequences and lengths, some of them with interesting sequences for bioactivity. This manuscript is presenting the proteomic identification of small peptides resulting from the hydrolysis of four target proteins (glyceraldehyde-3-phosphate dehydrogenase, beta-enolase, myozenin-1 and troponin T) and discusses the enzymatic routes for their generation during the dry-curing process. The results indicate that the hydrolysis of peptides follows similar exo-peptidase mechanisms. In the case of dry-fermented sausages, most of the observed hydrolysis is the result of the combined action of muscle and microbial exo-peptidases except for the hydrolysis of di- and tri-peptides, mostly due to microbial di- and tri-peptidases, and the release of amino acids at the C-terminal that appears to be mostly due to muscle carboxypeptidases.

  2. Structural modifications of lignocellulosics by pretreatments to enhance enzymatic hydrolysis

    SciTech Connect

    Gharpuray, M.M.; Lee, Y.F.; Fan, L.T.

    1983-01-01

    In this work an evaluation was made of a wide variety of single and multiple pretreatment methods for enhancing the rate of enzymatic hydrolysis of wheat straw. A multiple pretreatment consisted of a physical pretreatment followed by a chemical pretreatment. The structural features of wheat straw, including the specific surface area, crystallinity index, and lignin content, were measured to understand the mechanism of the enhancement in the hyrolysis rate upon pretreatment. It has been found that, in general, multiple pretreatments were not promising, since the hydrolysis rates rarely exceeded those achieved by single pretreatments. Ball-milling pretreatment was found to be effective in increasing the specific surface area and decreasing the crystallinity index. Treatment with ethylene glycol was highly effective in increasing the specific surface area, in addition to a high degree of delignification. Peracetic acid pretreatment was highly effective in delignifying substrate. Among multiple pretreatments, those involving peracetic acid treatment generally had lower crystallinity indices and lignin content values. The relationship between the hydrolysis rate and the set of structural features indicated that an increase in surface area and a decrease in the crystallinity and lignin content enhance the hydrolysis; the specific surface area is the most influential of the structural features, followed by the lignin content. (Refs. 23).

  3. Purification and characterization of a novel lactonohydrolase, catalyzing the hydrolysis of aldonate lactones and aromatic lactones, from Fusarium oxysporum.

    PubMed

    Shimizu, S; Kataoka, M; Shimizu, K; Hirakata, M; Sakamoto, K; Yamada, H

    1992-10-01

    A novel lactonohydrolase, an enzyme that catalyzes the hydrolysis of aldonate lactones to the corresponding aldonic acids, was purified 10-fold to apparent homogeneity, with a 61% overall recovery, from Fusarium oxysporum AKU 3702, through a purification procedure comprising DEAE-Sephacel, octyl-Sepharose CL-4B and hydroxyapatite chromatographies and crystallization. The molecular mass of the native enzyme, as estimated by high-performance gel-permeation chromatography, is 125 kDa, and the subunit molecular mass is 60 kDa. The enzyme contains 15.4% (by mass) glucose equivalent of carbohydrate, and about 1 mol calcium/subunit. The enzyme hydrolyzes aldonate lactones, such as D-galactono-gamma-lactone and L-mannono-gamma-lactone, stereospecifically. Furthermore, it can catalyze the asymmetric hydrolysis of D-pantoyl lactone, which is a promising chiral building block for the chemical synthesis of D-pantothenate. These reactions are reversible, and the reaction equilibrium at pH 6.0 has a molar ratio of nearly 1:1 with D-pantoyl lactone and D-pantoic acid. The Km and Vmax for D-galactono-gamma-lactone are 3.6 mM and 1440 U/mg, respectively, and those for D-galactonate are 52.6 mM and 216 U/mg, respectively. The enzyme also irreversibly hydrolyzes several aromatic lactones, such as dihydrocoumarin and homogentisic-acid lactone. PMID:1396712

  4. Lipase-catalyzed hydrolysis of TG containing acetylenic FA.

    PubMed

    Jie, Marcel S F Lie Ken; Fua, Xun; Lau, Maureen M L; Chye, M L

    2002-10-01

    Hydrolysis of symmetrical acetylenic TG of type AAA [viz., glycerol tri-(4-decynoate), glycerol tri-(6-octadecynoate), glycerol tri-(9-octadecynoate), glycerol tri-(10-undecynoate), and glycerol tri-(13-docosynoate)] in the presence of eight microbial lipases was studied. Novozyme 435 (Candida antarctica), an efficient enzyme for esterification, showed a significant resistance in the hydrolysis of glycerol tri-(9-octadecynoate) and glycerol tri-(13-docosynoate). Hydrolysis of acetylenic TG with Lipolase 100T (Humicola lanuginosa) was rapidly accomplished. Lipase PS-D (Pseudomonas cepacia) showed a fair resistance toward the hydrolysis of glycerol tri-(6-octadecynoate) only, which reflected its ability to recognize the delta6 positional isomer of 18:1. Lipase CCL (Candida cylindracea, syn. C. rugosa) and AY-30 (C. rugosa) were able to catalyze the release of 10-undecynoic acid and 9-octadecynoic acid from the corresponding TG, but less readily the 13-docosynoic acid in the case of glycerol tri-(13-docosynoate). The two lipases CCL and AY-30 were able to distinguish the small difference in structure of fatty acyl moieties in the TG substrate. To confirm this trend, three regioisomers of mixed acetylenic TG of type ABC (containing one each of delta6, delta9, and delta13 acetylenic FA in various positions) were prepared and hydrolyzed with CCL and AY-40. The results reconfirmed the observation that AY-30 and CCL were able to distinguish the slight differences in the molecular structure (position of the acetylenic bond and chain length) of the acyl groups in the TG during the hydrolysis of such TG substrates.

  5. Statistical evaluation of fatty acid profile and cholesterol content in fish (common carp) lipids obtained by different sample preparation procedures.

    PubMed

    Spiric, Aurelija; Trbovic, Dejana; Vranic, Danijela; Djinovic, Jasna; Petronijevic, Radivoj; Matekalo-Sverak, Vesna

    2010-07-01

    Studies performed on lipid extraction from animal and fish tissues do not provide information on its influence on fatty acid composition of the extracted lipids as well as on cholesterol content. Data presented in this paper indicate the impact of extraction procedures on fatty acid profile of fish lipids extracted by the modified Soxhlet and ASE (accelerated solvent extraction) procedure. Cholesterol was also determined by direct saponification method, too. Student's paired t-test used for comparison of the total fat content in carp fish population obtained by two extraction methods shows that differences between values of the total fat content determined by ASE and modified Soxhlet method are not statistically significant. Values obtained by three different methods (direct saponification, ASE and modified Soxhlet method), used for determination of cholesterol content in carp, were compared by one-way analysis of variance (ANOVA). The obtained results show that modified Soxhlet method gives results which differ significantly from the results obtained by direct saponification and ASE method. However the results obtained by direct saponification and ASE method do not differ significantly from each other. The highest quantities for cholesterol (37.65 to 65.44 mg/100 g) in the analyzed fish muscle were obtained by applying direct saponification method, as less destructive one, followed by ASE (34.16 to 52.60 mg/100 g) and modified Soxhlet extraction method (10.73 to 30.83 mg/100 g). Modified Soxhlet method for extraction of fish lipids gives higher values for n-6 fatty acids than ASE method (t(paired)=3.22 t(c)=2.36), while there is no statistically significant difference in the n-3 content levels between the methods (t(paired)=1.31). The UNSFA/SFA ratio obtained by using modified Soxhlet method is also higher than the ratio obtained using ASE method (t(paired)=4.88 t(c)=2.36). Results of Principal Component Analysis (PCA) showed that the highest positive impact to

  6. Fermentable sugars by chemical hydrolysis of biomass

    PubMed Central

    Binder, Joseph B.; Raines, Ronald T.

    2010-01-01

    Abundant plant biomass has the potential to become a sustainable source of fuels and chemicals. Realizing this potential requires the economical conversion of recalcitrant lignocellulose into useful intermediates, such as sugars. We report a high-yielding chemical process for the hydrolysis of biomass into monosaccharides. Adding water gradually to a chloride ionic liquid-containing catalytic acid leads to a nearly 90% yield of glucose from cellulose and 70–80% yield of sugars from untreated corn stover. Ion-exclusion chromatography allows recovery of the ionic liquid and delivers sugar feedstocks that support the vigorous growth of ethanologenic microbes. This simple chemical process, which requires neither an edible plant nor a cellulase, could enable crude biomass to be the sole source of carbon for a scalable biorefinery. PMID:20194793

  7. Storage oil hydrolysis during early seedling growth.

    PubMed

    Quettier, Anne-Laure; Eastmond, Peter J

    2009-06-01

    Storage oil breakdown plays an important role in the life cycle of many plants by providing the carbon skeletons that support seedling growth immediately following germination. This metabolic process is initiated by lipases (EC: 3.1.1.3), which catalyze the hydrolysis of triacylglycerols (TAGs) to release free fatty acids and glycerol. A number of lipases have been purified to near homogeneity from seed tissues and analysed for their in vitro activities. Furthermore, several genes encoding lipases have been cloned and characterised from plants. However, only recently has data been presented to establish the molecular identity of a lipase that has been shown to be required for TAG breakdown in seeds. In this review we briefly outline the processes of TAG synthesis and breakdown. We then discuss some of the biochemical literature on seed lipases and describe the cloning and characterisation of a lipase called SUGAR-DEPENDENT1, which is required for TAG breakdown in Arabidopsis thaliana seeds.

  8. Pretreatment and enzymatic hydrolysis of corn fiber

    SciTech Connect

    Grohmann, K.; Bothast, R.J.

    1996-10-01

    Corn fiber is a co-product of the corn wet milling industry which is usually marketed as a low value animal feed ingredient. Approximately 1.2 x 10{sup 6} dry tons of this material are produced annually in the United States. The fiber is composed of kernel cell wall fractions and a residual starch which can all be potentially hydrolyzed to a mixture of glucose, xylose, arabinose and galactose. We have investigated a sequential saccharification of polysaccharides in corn fiber by a treatment with dilute sulfuric acid at 100 to 160{degrees}C followed by partial neutralization and enzymatic hydrolysis with mixed cellulose and amyloglucosidase enzymes at 45{degrees}C. The sequential treatment achieved a high (approximately 85%) conversion of all polysaccharides in the corn fiber to monomeric sugars, which were in most cases fermentable to ethanol by the recombinant bacterium Escherichia coli KOll.

  9. A new route to improved glucose yields in cellulose hydrolysis

    SciTech Connect

    Zhao, Haibo; Holladay, John E.; Kwak, Ja Hun; Zhang, Z. Conrad

    2007-08-01

    An unusual inverse temperature-dependent pathway was discovered for cellulose decrystallization in trifluoroacetic acid (TFA). Cellulose was completely decrystallized by TFA at 0 °C in less than 2 hours, a result not achieved in 48 hours at 25°C in the same medium. The majority of TFA used in cellulose decrystallization was recycled via a vacuum process. The small remaining amount of TFA was diluted with water to make a 0.5% TFA solution and used as a catalyst in dilute acid hydrolysis. After one minute, under batch conditions at 185 °C, the glucose yield reached 63.5% without production of levulinic acid. In comparison, only 15.0% glucose yield was achieved in the hydrolysis of untreated cellulose by 0.5% H2SO4 under the same condition. Further improvement of glucose yield is possible by optimizing reaction conditions. Alternatively, the remaining TFA can be completely removed by water while keeping the regenerated cellulose in a highly amorphous state. This regenerated cellulose is much more reactive than untreated cellulose in hydrolysis reactions, but still less reactive than corn starch. The lower temperatures and shorter reaction times with this activated cellulose makes it possible to reduce operating costs and decrease byproduct yields such as HMF and levulinic acid.

  10. Hydrolysis behavior of regenerated celluloses with different degree of polymerization under microwave radiation.

    PubMed

    Ni, Jinping; Teng, Na; Chen, Haizhen; Wang, Jinggang; Zhu, Jin; Na, Haining

    2015-09-01

    This work studied the hydrolysis behavior of regenerated celluloses (RCs) with different degree of polymerization (DP) by using the catalyst of dilute acid under microwave radiation. Results showed that the DP had a considerable influence on hydrolysis of cellulose. The reactivity of RCs was significantly improved when DP was lower than 51. The highest sugar yield of 59.2% was achieved from RC with lowest DP of 23 at 160 °C for 15 min. But the lowest yield of 32.6% was obtained when RC with highest DP of 132 was used. Recrystallization of cellulose was found to hinder the further hydrolysis particularly with the high DP. The effect of recrystallization can be reduced by the decrease of DP of RCs. This research demonstrates that the DP of RCs plays a crucial role on hydrolysis and it provides a preliminary guide based on DP to find a suitable pretreatment method for cellulose hydrolysis.

  11. Hippurate hydrolysis by Legionella pneumophila.

    PubMed Central

    Hébert, G A

    1981-01-01

    Strains of Legionella pneumophila were shown to hydrolyze sodium hippurate in an overnight test system, but strains of L. bozemanii, L. micdadei, L. dumoffii, and some other organisms similar to the legionellae did not. Although only a small number of strains of legionellae other than L. pneumophila have been classified and tested, the results indicate that the hippurate hydrolysis test may prove useful for differentiating among Legionella species. PMID:7462418

  12. Simultaneous pretreatment and enzymatic hydrolysis of forage biomass

    SciTech Connect

    Henk, L.; Linden, J.C.

    1993-12-31

    Sweet sorghum is an attractive fermentation feedstock because as much as 40% of the dry weight consists of readily femented sugars such as sucrose, glucose and frutose. Cellulose and hemicellulose comprise another 50%. However, if this material is to be used a year-round feedstock for ethanol production, a stable method of storage must be developed to maintain the sugar content. A modified version of the traditional ensiling process is made effective by the addition of cellulolytic/hemicellulolytic enzymes and lactic acid bacteria to freshly chopped sweet sorghum prior to the production of silage. In situ hydrolysis of cellulose and hemicellulose occurs concurrently with the acidic ensiling fementation. By hydolyzing the acetyl groups using acetyl xylan esterase and 3-0-methyl glucuronyl side chains using pectinase from hemicellulose, cellulose becomes accessible to hydrolysis by cellulase, both during in situ ensiling with enzymes and in the simultaneous saccharification and fermentation (SSF) to ethanol.

  13. Enzymatic hydrolysis of corn stover process development and evaluation

    SciTech Connect

    Perez, J.; Wilke, C.R.; Blanch, H.W.

    1981-12-01

    The hydrolysis of acid treated corn stover with cellulase from T. reesei Rut-C-30 was evaluated. Experiments were conducted with substrate concentrations of 5 to 25% by weight, enzyme activities of 0.5 to 7 IU/ml and residence times of 24 to 48 hours. Maximum conversion was 55% for specific cellulase activity of 25 to 30 IU/g. Optimum cellobiase activity for minimum cellobiose production was found to be approximately 1.8 cellobiase units to 1 FPA unit. Hydrolysis experiments with steam exploded corn stover led to a maximum conversion of 80%, significantly higher than the results obtained for acid treated substrate. Steam exploded corn stover was demonstrated as a suitable carbon source for growth of T. reesei in submerged cultures.

  14. Hydrolysis and fractionation of lignocellulosic biomass

    DOEpatents

    Torget, Robert W.; Padukone, Nandan; Hatzis, Christos; Wyman, Charles E.

    2000-01-01

    A multi-function process is described for the hydrolysis and fractionation of lignocellulosic biomass to separate hemicellulosic sugars from other biomass components such as extractives and proteins; a portion of the solubilized lignin; cellulose; glucose derived from cellulose; and insoluble lignin from said biomass comprising one or more of the following: optionally, as function 1, introducing a dilute acid of pH 1.0-5.0 into a continual shrinking bed reactor containing a lignocellulosic biomass material at a temperature of about 94 to about 160.degree. C. for a period of about 10 to about 120 minutes at a volumetric flow rate of about 1 to about 5 reactor volumes to effect solubilization of extractives, lignin, and protein by keeping the solid to liquid ratio constant throughout the solubilization process; as function 2, introducing a dilute acid of pH 1.0-5.0, either as virgin acid or an acidic stream from another function, into a continual shrinking bed reactor containing either fresh biomass or the partially fractionated lignocellulosic biomass material from function 1 at a temperature of about 94-220.degree. C. for a period of about 10 to about 60 minutes at a volumetric flow rate of about 1 to about 5 reactor volumes to effect solubilization of hemicellulosic sugars, semisoluble sugars and other compounds, and amorphous glucans by keeping the solid to liquid ratio constant throughout the solubilization process; as function 3, optionally, introducing a dilute acid of pH 1.0-5.0 either as virgin acid or an acidic stream from another function, into a continual shrinking bed reactor containing the partially fractionated lignocellulosic biomass material from function 2 at a temperature of about 180-280.degree. C. for a period of about 10 to about 60 minutes at a volumetric flow rate of 1 to about 5 reactor volumes to effect solubilization of cellulosic sugars by keeping the solid to liquid ratio constant throughout the solubilization process; and as function 4

  15. Hydrolysis of amphenicol and macrolide antibiotics: Chloramphenicol, florfenicol, spiramycin, and tylosin.

    PubMed

    Mitchell, Shannon M; Ullman, Jeffrey L; Teel, Amy L; Watts, Richard J

    2015-09-01

    Antibiotics that enter the environment can present human and ecological health risks. An understanding of antibiotic hydrolysis rates is important for predicting their environmental persistence as biologically active contaminants. In this study, hydrolysis rates and Arrhenius constants were determined as a function of pH and temperature for two amphenicol (chloramphenicol and florfenicol) and two macrolide (spiramycin and tylosin) antibiotics. Antibiotic hydrolysis rates in pH 4-9 buffer solutions at 25°C, 50°C, and 60°C were quantified, and degradation products were characterized. All of the antibiotics tested remained stable and exhibited no observable hydrolysis under ambient conditions typical of aquatic ecosystems. Acid- and base-catalyzed hydrolysis occurred at elevated temperatures (50-60°C), and hydrolysis rates increased considerably below pH 5 and above pH 8. Hydrolysis rates also increased approximately 1.5- to 2.9-fold for each 10°C increase in temperature. Based on the degradation product masses found, the functional groups that underwent hydrolysis were alkyl fluoride, amide, and cyclic ester (lactone) moieties; some of the resultant degradation products may remain bioactive, but to a lesser extent than the parent compounds. The results of this research demonstrate that amphenicol and macrolide antibiotics persist in aquatic systems under ambient temperature and pH conditions typical of natural waters. Thus, these antibiotics may present a risk in aquatic ecosystems depending on the concentration present.

  16. HYDROLYSIS

    EPA Science Inventory

    Hydrolytic processes provide the baseline loss rate for any chemical in an aqueous envi- ronment. Although various hydrolytic pathways account for significant degradation of certain classes of organic chemicals, other organic structures are completely inert. Strictly speaking, hy...

  17. Regiospecific Ester Hydrolysis by Orange Peel Esterase - An Undergraduate Experiment.

    NASA Astrophysics Data System (ADS)

    Bugg, Timothy D. H.; Lewin, Andrew M.; Catlin, Eric R.

    1997-01-01

    A simple but effective experiment has been developed to demonstrate the regiospecificity of enzyme catalysis using an esterase activity easily isolated from orange peel. The experiment involves the preparation of diester derivatives of para-, meta- and ortho-hydroxybenzoic acid (e.g. methyl 4-acetoxy-benzoic acid). The derivatives are incubated with orange peel esterase, as a crude extract, and with commercially available pig liver esterase and porcine pancreatic lipase. The enzymatic hydrolysis reactions are monitored by thin layer chromatography, revealing which of the two ester groups is hydrolysed, and the rate of the enzyme-catalysed reaction. The results of a group experiment revealed that in all cases hydrolysis was observed with at least one enzyme, and in most cases the enzymatic hydrolysis was specific for production of either the hydroxy-ester or acyl-acid product. Specificity towards the ortho-substituted series was markedly different to that of the para-substituted series, which could be rationalised in the case of pig liver esterase by a published active site model.

  18. Enzymatic hydrolysis of defatted mackerel protein with low bitter taste

    NASA Astrophysics Data System (ADS)

    Hou, Hu; Li, Bafang; Zhao, Xue

    2011-03-01

    Ultrasound-assisted solvent extraction was confirmed as a novel, effective method for separating lipid from mackerel protein, resulting in a degreasing rate (DR) of 95% and a nitrogen recovery (NR) of 88.6%. To obtain protein hydrolysates with high nitrogen recovery and low bitter taste, enzymatic hydrolysis was performed using eight commercially available proteases. It turned out that the optimum enzyme was the `Mixed enzymes for animal proteolysis'. An enzyme dosage of 4%, a temperature of 50°, and a hydrolysis time of 300 min were found to be the optimum conditions to obtain high NR (84.28%) and degree of hydrolysis (DH, 16.18%) by orthogonal experiments. Glutamic acid was the most abundant amino acid of MDP (defatted mackerel protein) and MDPH (defatted mackerel protein hydrolysates). Compared with the FAO/WHO reference protein, the essential amino acid chemical scores (CS) were greater than 1.0 (1.0-1.7) in MDPH, which is reflective of high nutritional value. This, coupled with the light color and slight fishy odor, indicates that MDPH would potentially have a wide range of applications such as nutritional additives, functional ingredients, and so on.

  19. Quest for a reliable, valid, and sensitive in situ hybridization procedure to detect viral nucleic acids in the central nervous system.

    PubMed

    Tourtellotte, W W; Schmid, P; Pick, P; Verity, N; Martinez, S; Shapshak, P

    1987-06-01

    In situ hybridization (ISH) to detect and to quantitate viral nucleic acid sequences in cryopreserved central nervous system (CNS) tissue is a reliable, valid and sensitive molecular technique. On the other hand, utilization of formaldehyde fixed paraffin embedded (FFPE) tissue to improve cytomorphology requires fundamental changes in the procedure since it is necessary to cleave the elaborate protein network cross-linked by formaldehyde using elevated concentrations of proteinases in order to permit diffusion of complementary DNA probes to the targets (genomic viral nucleic acid sequences and/or viral mRNA). Adversely, this procedure hydrolyzed the proteinaceous glues generally used to fix tissue to glass slides resulting in loss of tissue sections during the ISH protocol. This report describes the application of a novel procedure utilizing a silano-organic compound to covalently bond to glass slides FFPE sections as well as cryopreserved tissue sections and cultured cells with and without virus infections. This covalent bonding procedure has permitted optimization of the ISH procedure for virus detection and quantification, especially for exploratory studies of specificity and wash stringency in relation to the Tm of the hybridized product. Progressive multifocal leucoencephalopathy (PML) caused by an opportunistic papovavirus (JC) was chosen because of the ready availability of tissue, stability of papovavirus nucleic acids, and specificity of 3H- and 35S-radiolabeled JC cloned DNA probes. Further, this laboratory is utilizing the optimized sensitive procedure to search for several virus etiologies in human diseases such as multiple sclerosis, temporal lobe epilepsy, Alzheimer's disease, schizophrenia, and Parkinson's disease, as well as normal aging.(ABSTRACT TRUNCATED AT 250 WORDS)

  20. An isozyme of earthworm serine proteases acts on hydrolysis of triacylglycerol.

    PubMed

    Nakajima, Nobuyoshi; Sugimoto, Manabu; Tsuboi, Sadao; Tsuji, Hideaki; Ishihara, Kohji

    2005-10-01

    An enzyme catalyzing the hydrolysis of triacylglycerol was purified from an earthworm. The N-terminal amino acid sequence and the catalytic function of the purified enzyme were identical to those of Isozyme C, an isozyme of the earthworm-serine proteases. No other lipase proteins were found in the earthworm cells. The isozyme might act on the hydrolysis of triacylglycerol as well as the protein decomposition.

  1. Enzymatic hydrolysis and fermentation of agricultural residues to ethanol

    SciTech Connect

    Mes-Hartree, M.; Hogan, C.M.; Saddler, J.N.

    1984-01-01

    A combined enzymatic hydrolysis and fermentation process was used to convert steam-treated wheat and barley straw to ethanol. Maximum conversion efficiencies were obtained when the substrates were steamed for 90 s. These substrates could yield over 0.4 g ethanol/g cellulose following a combined enzymatic hydrolysis and fermentation process procedure using culture filtrates derived from Trichoderma harzianum E58. When culture filtrates from Trichoderma reesei C30 and T. reesei QM9414 were used, the ethanol yields obtained were 0.32 and 0.12 g ethanol/g cellulose utilized, respectively. The lower ethanol yields obtained with these strains were attributed to the lower amounts of ..beta..-glucosidase detected in the T. reesei culture filtrates.

  2. Generation of group B soyasaponins I and III by hydrolysis.

    PubMed

    Zhang, Wei; Teng, Su Ping; Popovich, David G

    2009-05-13

    Soyasaponins are a group of oleanane triterpenoids found in soy and other legumes that have been associated with some of the benefits achieved by consuming plant-based diets. However, these groups of compounds are diverse and structurally complicated to chemically characterize, separate from the isoflavones, and isolate in sufficient quantities for bioactive testing. Therefore, the aim of this study was to maximize the extraction of soyasaponins from soy flour, remove isoflavones, separate group B soyasaponins from group A, and produce an extract that contained a majority of non-DDMP (2,3-dihydro-2,5-dihydroxy-6-methyl-4H-pyran-4-one)-conjugated group B soyasaponins I and III. Room temperature extraction in methanol for 24 or 48 h resulted in the maximum recovery of soyasaponins, and Soxhlet extraction resulted in the least. A solid-phase extraction using methanol (45%) was found to virtually eliminate the interfering isoflavones as compared to butanol-water liquid-liquid extraction and ammonium sulfate precipitation, while maximizing saponin recovery. Alkaline hydrolysis in anhydrous methanol produced the maximum amount of soyasaponins I and III as compared to aqueous methanol and acid hydrolysis in both aqueous and anhydrous methanol. The soyasaponin I amount was increased by 175%, and soyasaponin III was increased by 211% after alkaline hydrolysis. Furthermore, after alkaline hydrolysis, a majority of DDMP-conjugated group B soyasaponins such as betag, betaa, gammag, and gammaa transformed into the non-DDMP-conjugated soyasaponins I and III without affecting the glycosidic bond at position C-3 of the ring structure. Therefore, we have developed a method that maximizes the recovery of DDMP-conjugated saponins and uses alkaline hydrolysis to produce an extract containing mainly soyasaponins I and III. PMID:19338335

  3. [Oxytetracycline and oxolinic acid residues in kuruma prawn (Penaeus japonicus) and the effect of cooking procedures on the residues].

    PubMed

    Uno, Kazuaki

    2002-04-01

    Tissue distribution and residue depletion of oxytetracycline (OTC) and oxolinic acid (OA) were studied in the kuruma prawn (Penaeus japonicus). The prawn were kept in tanks with recirculated artificial seawater at a salinity of 22-23@1000. The water temperature was maintained at 25 degrees C. The average body weight was 22.9 +/- 4.9 g for OTC and 22.5 +/- 3.6 g for OA. The drug was mixed with the diet and orally administered through a catheter to the prawn. The doses of OTC and OA, respectively, were 50 mg/kg body weight. At each sample time, four prawns were sacrificed and tissues were sampled. OTC and OA levels were determined by high-performance liquid chromatography. At the highest levels, the concentrations of OTC were in the other: shell (13.57 micrograms/g) > hemolymph (12.20 micrograms/mL) > muscle (8.30 micrograms/g). For OA, the order was: shell (20.74 micrograms/g) > hemolymph (7.06 micrograms/mL) > muscle (2.05 micrograms/g). The elimination half-lives of hemolymph and muscle were 44.7 and 46.8 hours for OTC and 55.0 and 107.9 hours for OA, respectively. Residual OTC could not be detected in hemolymph and muscle at 20 days after dosing. Residual OA disappeared from hemolymph and muscle at 25 days after dosing. A 25-day period for OTC and 30-day period for OA could be regarded as the proper withdrawal time established for kuruma prawn by the Pharmaceutical Law in Japan. However, the elimination half-lives of shell for OTC and OA could not be calculated because both drug residues persisted in shell tissues, and the elimination phase was not completed during the experimental period. Residual OTC (14.10 +/- 2.26 micrograms/g, n = 6) and OA (0.32 +/- 0.06 microgram/g, n = 7) were detected in exuviae at 3 days and 4 days after dosing, respectively. Residual OTC was reduced to 50-70% in muscle by the usual methods of cooking (boiling, baking at 200 degrees C and frying at 180 degrees C), whereas reduction levels in shell were only 20-30%. Residual OA was

  4. Hydrolysis of iron and chromium fluorides: mechanism and kinetics.

    PubMed

    Gálvez, José L; Dufour, Javier; Negro, Carlos; López-Mateos, Federico

    2008-06-15

    Fluoride complexes of metallic ions are one of the main problems when processing industrial effluents with high content of fluoride anion. The most important case is derived from pickling treatment of stainless steel, which is performed with HNO3/HF mixtures to remove oxides scale formed over the metal surface. Waste from this process, spent pickling liquor, must be treated for recovering metallic and acid content. Conventional treatments produce a final effluent with high quantity of fluoride complexes of iron and chromium. This work proposes a hydrolysis treatment of these solid metal fluorides by reacting them with a basic agent. Metal oxides are obtained, while fluoride is released to solution as a solved salt, which can be easily recovered as hydrofluoric acid. Solid iron and chromium fluorides, mainly K2FeF5(s) and CrF3(s), obtained in the UCM treatment process, were employed in this work. Optimal hydrolysis operating conditions were obtained by means of a factorial design: media must be basic but pH cannot be higher than 9.5, temperature from 40 to 70 degrees C and alkali concentration (potassium hydroxide) below 1.1 mol L(-1). Secondary reactions have been detected, which are probably due to fluoride adsorption onto obtained oxides surface. Mechanism of reaction consists of several stages, involving solid fluoride dissolution and complexes decomposition. Hydrolysis kinetics has been modeled with classical crystal dissolution kinetics, based on mass transfer phenomena. PMID:17988794

  5. Feasibility of pressurization to speed up enzymatic hydrolysis of biological materials for multielement determinations.

    PubMed

    Moreda-Piñeiro, Antonio; Bermejo-Barrera, Adela; Bermejo-Barrera, Pilar; Moreda-Piñeiro, Jorge; Alonso-Rodríguez, Elia; Muniategui-Lorenzo, Soledad; López-Mahía, Purificación; Prada-Rodríguez, Darío

    2007-03-01

    The feasibility of pressurized solvents (liquids at a high pressure and/or high temperature without the subcritical point being reached) has been newly investigated to accelerate enzymatic hydrolysis processes of mussel tissue for multielement determinations. The target elements (Al, As, Cd, Co, Cu, Fe, Hg, Li, Mn, Pb, Se, Sr, V, and Zn) were released from dried mussel tissue by action of two proteases (pepsin and pancreatin), and they have been evaluated by inductively coupled plasma optical emission spectrometry (ICP-OES). Variables inherent to the enzymatic activity (pH, ionic strength, temperature, and enzyme mass) and factors affecting pressurization (static time, pressure, and number of cycles) were simultaneously studied by applying a Plackett-Burman design (PBD) as the screening method. Results showed that pH, ionic strength, and temperature were the most statistically significant factors (confidence interval of 95%) under pressurized conditions for pepsin, while pH and ionic strength affected pancreatin activity. This means that metal extraction is mostly attributed to enzymatic activity. The static time (enzymatic hydrolysis time) was found statistically nonsignificant for most of the elements, meaning that the hydrolysis procedure can be finished within a 2-15 min range. For pepsin, optimized conditions (pH 1.0, temperature 40 degrees C, pressure 1500 psi, static time 2 min, and number of cycles 3) gave quantitative extractions for As, Cd, Co, Cu, Hg, Li, Mn, Pb, Se, Sr, V, and Zn. The pepsin mass was 0.05 g, and the solution was Milli-Q water at pH 1.0 (adjusted with hydrochloric acid). For pancreatin, quantitative recoveries were only reached for As, Cd, Cu, Li, Pb, and Sr at room temperature, at a pressure of 1500 psi, for a static time of 2 min and a number of cycles of 3. The extraction solution was a 0.3 M potassium dihydrogen phosphate/potassium hydrogen phosphate buffer at a pH of 7.5 working at room temperature. Around 0.5 g of diatomaceous

  6. The BEI hydrolysis process and reactor system refined engineering proto-type. BEI pilot-plant improvement and operations demonstrations

    SciTech Connect

    Brelsford, Donald L.

    1999-10-01

    This BEI project involves BEI-HP and RS's applications toward potential commercial validity demonstrations for dilute-acid corn-fiber cellulose-hydrolysis processing with an aim toward fuel ethanol production.

  7. Pseudomonas aeruginosa arylsulfatase: a purified enzyme for the mild hydrolysis of steroid sulfates.

    PubMed

    Stevenson, Bradley J; Waller, Christopher C; Ma, Paul; Li, Kunkun; Cawley, Adam T; Ollis, David L; McLeod, Malcolm D

    2015-10-01

    The hydrolysis of sulfate ester conjugates is frequently required prior to analysis for a range of analytical techniques including gas chromatography-mass spectrometry (GC-MS). Sulfate hydrolysis may be achieved with commercial crude arylsulfatase enzyme preparations such as that derived from Helix pomatia but these contain additional enzyme activities such as glucuronidase, oxidase, and reductase that make them unsuitable for many analytical applications. Strong acid can also be used to hydrolyze sulfate esters but this can lead to analyte degradation or increased matrix interference. In this work, the heterologously expressed and purified arylsulfatase from Pseudomonas aeruginosa is shown to promote the mild enzyme-catalyzed hydrolysis of a range of steroid sulfates. The substrate scope of this P. aeruginosa arylsulfatase hydrolysis is compared with commercial crude enzyme preparations such as that derived from H. pomatia. A detailed kinetic comparison is reported for selected examples. Hydrolysis in a urine matrix is demonstrated for dehydroepiandrosterone 3-sulfate and epiandrosterone 3-sulfate. The purified P. aeruginosa arylsulfatase contains only sulfatase activity allowing for the selective hydrolysis of sulfate esters in the presence of glucuronide conjugates as demonstrated in the short three-step chemoenzymatic synthesis of 5α-androstane-3β,17β-diol 17-glucuronide (ADG, 1) from epiandrosterone 3-sulfate. The P. aeruginosa arylsulfatase is readily expressed and purified (0.9 g per L of culture) and thus provides a new and selective method for the hydrolysis of steroid sulfate esters in analytical sample preparation.

  8. Microwave Pretreatment For Hydrolysis Of Cellulose

    NASA Technical Reports Server (NTRS)

    Cullingford, Hatice S.; George, Clifford E.; Lightsey, George R.

    1993-01-01

    Microwave pretreatment enhances enzymatic hydrolysis of cellulosic wastes into soluble saccharides used as feedstocks for foods, fuels, and other products. Low consumption of energy, high yield, and low risk of proposed hydrolysis process incorporating microwave pretreatment makes process viable alternative to composting.

  9. Rate of Hydrolysis of Tertiary Halogeno Alkanes

    ERIC Educational Resources Information Center

    Pritchard, D. R.

    1978-01-01

    Describes an experiment to measure the relative rate of hydrolysis of the 2-x-2 methylpropanes, where x is bromo, chloro or iodo. The results are plotted on a graph from which the relative rate of hydrolysis can be deduced. (Author/GA)

  10. Recycle of enzymes and substrate following enzymatic hydrolysis of steam-pretreated aspenwood.

    PubMed

    Mes-Hartree, M; Hogan, C M; Saddler, J N

    1987-09-01

    The commercial production of chemicals and fuels from lignocellulosic residues by enzymatic means still requires considerable research on both the technical and economic aspects. Two technical problems that have been identified as requiring further research are the recycle of the enzymes used in hydrolysis and the reuse of the re calcitrant cellulose remaining after incomplete hydrolysis. Enzyme recycle is required to lower the cost of the enzymes, while the reuse of the spent cellulose will lower the feedstock cost. The conversion process studied was a combined enzymatic hydrolysis and fermentation (CHF) procedure that utilized the cellulolytic enzymes derived from the fungus Trichoderma harzianum E58 and the yeast Saccharomyces cerevisiae. The rate and extent of hydrolysis and ethanol production was monitored as was the activity and hydrolytic potential of the enzymes remaining in the filtrate after the hydrolysis period. When a commercial cellulose was used as the substrate for a routine 2-day CHF process, 60% of the original treated, water-extracted aspenwood was used as the substrate, only 13% of the original filter paper activity was detected after a similar procedure. The combination of 60% spent enzymes with 40% fresh enzymes resulted in the production of 30% less reducing sugars than the original enzyme mixture. Since 100% hydrolysis of the cellulose portion is seldom accomplished in an enzymatic hydrolysis pro cess, the residual cellulose was used as a substrate for the growth of T. harzianum E58 and production of celulolytic enzymes. The residue remaining after the CHF process was used as a substrate for the production of the cellulolytic enzymes. The production of enzymes from the residue of the Solka Floc hydrolysis was greater than the production of enzymes from the original Solka Floc.

  11. Novel Penicillium cellulases for total hydrolysis of lignocellulosics.

    PubMed

    Marjamaa, Kaisa; Toth, Karolina; Bromann, Paul Andrew; Szakacs, George; Kruus, Kristiina

    2013-05-10

    The (hemi)cellulolytic systems of two novel lignocellulolytic Penicillium strains (Penicillium pulvillorum TUB F-2220 and P. cf. simplicissimum TUB F-2378) have been studied. The cultures of the Penicillium strains were characterized by high cellulase and β-glucosidase as well moderate xylanase activities compared to the Trichoderma reesei reference strains QM 6a and RUTC30 (volumetric or per secreted protein, respectively). Comparison of the novel Penicillium and T. reesei secreted enzyme mixtures in the hydrolysis of (ligno)cellulose substrates showed that the F-2220 enzyme mixture gave higher yields in the hydrolysis of crystalline cellulose (Avicel) and similar yields in hydrolysis of pre-treated spruce and wheat straw than enzyme mixture secreted by the T. reesei reference strain. The sensitivity of the Penicillium cellulase complexes to softwood (spruce) and grass (wheat straw) lignins was lignin and temperature dependent: inhibition of cellulose hydrolysis in the presence of wheat straw lignin was minor at 35°C while at 45°C by spruce lignin a clear inhibition was observed. The two main proteins in the F-2220 (hemi)cellulase complex were partially purified and identified by peptide sequence similarity as glycosyl hydrolases (cellobiohydrolases) of families 7 and 6. Adsorption of the GH7 enzyme PpCBH1 on cellulose and lignins was studied showing that the lignin adsorption of the enzyme is temperature and pH dependent. The ppcbh1 coding sequence was obtained using PCR cloning and the translated amino acid sequence of PpCBH1 showed up to 82% amino acid sequence identity to known Penicillium cellobiohydrolases.

  12. The crystallinity of calcium phosphate powders influenced by the conditions of neutralized procedure with citric acid additions

    SciTech Connect

    Li Chengfeng

    2009-05-06

    Calcium phosphate powders with nano-sized crystallinity were synthesized by neutralization using calcium hydroxide and orthophosphoric acid with the assistance of citric acid. The influence of processing parameters, such as free or additive citric acid, synthetic temperature and ripening time, on the crystallinity of hydroxyapatite were investigated. The results of X-ray diffraction and microstructure observations showed that the crystallinity and morphology of nano-sized hydroxyapatite particles were influenced by the presence or absence of citric acid. It was found that the crystallinities and crystallite sizes of hydroxyapatite powders prepared with the additive citric acid increased with increasing synthetic temperature and ripening time. Especially, the crystallinities of (h k 0) planes were raised and more homogeneously grown particles were obtained with increasing synthetic temperature.

  13. Hydrolysis of Virgin Coconut Oil Using Immobilized Lipase in a Batch Reactor

    PubMed Central

    Chua, Lee Suan; Alitabarimansor, Meisam; Lee, Chew Tin; Mat, Ramli

    2012-01-01

    Hydrolysis of virgin coconut oil (VCO) had been carried out by using an immobilised lipase from Mucor miehei (Lipozyme) in a water-jacketed batch reactor. The kinetic of the hydrolysis was investigated by varying the parameters such as VCO concentration, enzyme loading, water content, and reaction temperature. It was found that VCO exhibited substrate inhibition at the concentration more than 40% (v/v). Lipozyme also achieved the highest production of free fatty acids, 4.56 mM at 1% (w/v) of enzyme loading. The optimum water content for VCO hydrolysis was 7% (v/v). A relatively high content of water was required because water was one of the reactants in the hydrolysis. The progress curve and the temperature profile of the enzymatic hydrolysis also showed that Lipozyme could be used for free fatty acid production at the temperature up to 50°C. However, the highest initial reaction rate and the highest yield of free fatty acid production were at 45 and 40°C, respectively. A 100 hours of initial reaction time has to be compensated in order to obtain the highest yield of free fatty acid production at 40°C. PMID:22953055

  14. Comparison of multi-enzyme and thermophilic bacteria on the hydrolysis of mariculture organic waste (MOW).

    PubMed

    Guo, Liang; Sun, Mei; Zong, Yan; Zhao, Yangguo; Gao, Mengchun; She, Zonglian

    2016-01-01

    Mariculture organic waste (MOW) is rich in organic matter, which is a potential energy resource for anaerobic digestion. In order to enhance the anaerobic fermentation, the MOW was hydrolyzed by multi-enzyme and thermophilic bacteria. It was advantageous for soluble chemical oxygen demand (SCOD) release at MOW concentrations of 6 and 10 g/L with multi-enzyme and thermophilic bacteria pretreatments. For multi-enzyme, the hydrolysis was not obvious at substrate concentrations of 1 and 3 g/L, and the protein and carbohydrate increased with hydrolysis time at substrate concentrations of 6 and 10 g/L. For thermophilic bacteria, the carbohydrate was first released at 2-4 h and then consumed, and the protein increased with hydrolysis time. The optimal enzyme hydrolysis for MOW was determined by measuring the changes of SCOD, protein, carbohydrate, ammonia and total phosphorus, and comparing with acid and alkaline pretreatments.

  15. Modeling and simulation of an enzymatic reactor for hydrolysis of palm oil.

    PubMed

    Bhatia, S; Naidu, A D; Kamaruddin, A H

    1999-01-01

    Hydrolysis of palm oil has become an important process in Oleochemical industries. Therefore, an investigation was carried out for hydrolysis of palm oil to fatty acid and glycerol using immobilized lipase in packed bed reactor. The conversion vs. residence time data were used in Michaelis-Menten rate equation to evaluate the kinetic parameters. A mathematical model for the rate of palm oil hydrolysis was proposed incorporating role of external mass transfer and pore diffusion. The model was simulated for steady-state isothermal operation of immobilized lipase packed bed reactor. The experimental data were compared with the simulated results. External mass transfer was found to affect the rate of palm oil hydrolysis at higher residence time.

  16. Comparison of multi-enzyme and thermophilic bacteria on the hydrolysis of mariculture organic waste (MOW).

    PubMed

    Guo, Liang; Sun, Mei; Zong, Yan; Zhao, Yangguo; Gao, Mengchun; She, Zonglian

    2016-01-01

    Mariculture organic waste (MOW) is rich in organic matter, which is a potential energy resource for anaerobic digestion. In order to enhance the anaerobic fermentation, the MOW was hydrolyzed by multi-enzyme and thermophilic bacteria. It was advantageous for soluble chemical oxygen demand (SCOD) release at MOW concentrations of 6 and 10 g/L with multi-enzyme and thermophilic bacteria pretreatments. For multi-enzyme, the hydrolysis was not obvious at substrate concentrations of 1 and 3 g/L, and the protein and carbohydrate increased with hydrolysis time at substrate concentrations of 6 and 10 g/L. For thermophilic bacteria, the carbohydrate was first released at 2-4 h and then consumed, and the protein increased with hydrolysis time. The optimal enzyme hydrolysis for MOW was determined by measuring the changes of SCOD, protein, carbohydrate, ammonia and total phosphorus, and comparing with acid and alkaline pretreatments. PMID:27120653

  17. Enzymatic hydrolysis preparation of mono-O-lauroylsucrose via a mono-O-lauroylraffinose intermediate.

    PubMed

    Lu, Yuyun; Yan, Rian; Ma, Xiang; Wang, Yong; Sun, Yuankui; Luo, Zhongming

    2013-10-01

    1'-O-Lauroylsucrose and 6'-O-lauroylsucrose were formed through hydrolysis of the C-6″ galactose group of 1'-O-lauroylraffinose and 6'-O-lauroylraffinose, respectively, in the presence of α-galactosidase. The enzymatic hydrolysis of 1'-O-lauroylraffinose and 6'-O-lauroylraffinose is discussed in detail. Acetic acid-sodium acetate was chosen as the buffer solution of the enzymatic hydrolysis reaction. The optimum conditions for the enzymatic hydrolysis reaction were as follows: buffer solution, pH 3.8; enzymatic time, 48 h; and enzymatic temperature, 37 °C. Under the optimal process conditions, the efficiency of α-galactosidase was ca. 82.6%. The isomers were fully compared in solubility, hydrophile-lipophile balance (HLB) values, critical micelle concentration (CMC), and thermal stability. The results showed that all lauroylsucrose isomers have similar solubilities in polar solvent, HLB values, CMC values, and thermal stabilities.

  18. Synthesis, hydrolysis and stability of psilocin glucuronide.

    PubMed

    Martin, Rafaela; Schürenkamp, Jennifer; Pfeiffer, Heidi; Lehr, Matthias; Köhler, Helga

    2014-04-01

    A two-step synthesis of psilocin glucuronide (PCG), the main metabolite of psilocin, with methyl 2,3,4-tri-O-isobutyryl-1-O-trichloroacetimidoyl-α-d-glucopyranuronate is reported. With the synthesized PCG, hydrolysis conditions in serum and urine were optimized. Escherichia coli proved to be a better enzyme source for β-glucuronidase than Helix pomatia. It was essential to add ascorbic acid to serum samples to protect psilocin during incubation. Furthermore the stability of PCG and psilocin was compared as stability data are the basis for forensic interpretation of measurements. PCG showed a greater long-term stability after six months in deep frozen serum and urine samples than psilocin. The short-term stability of PCG for one week in whole blood at room temperature and in deep frozen samples was also better than that of psilocin. Therefore, PCG can be considered to be more stable than the labile psilocin and should always be included if psilocin is analyzed in samples. PMID:24513688

  19. Synthesis, hydrolysis and stability of psilocin glucuronide.

    PubMed

    Martin, Rafaela; Schürenkamp, Jennifer; Pfeiffer, Heidi; Lehr, Matthias; Köhler, Helga

    2014-04-01

    A two-step synthesis of psilocin glucuronide (PCG), the main metabolite of psilocin, with methyl 2,3,4-tri-O-isobutyryl-1-O-trichloroacetimidoyl-α-d-glucopyranuronate is reported. With the synthesized PCG, hydrolysis conditions in serum and urine were optimized. Escherichia coli proved to be a better enzyme source for β-glucuronidase than Helix pomatia. It was essential to add ascorbic acid to serum samples to protect psilocin during incubation. Furthermore the stability of PCG and psilocin was compared as stability data are the basis for forensic interpretation of measurements. PCG showed a greater long-term stability after six months in deep frozen serum and urine samples than psilocin. The short-term stability of PCG for one week in whole blood at room temperature and in deep frozen samples was also better than that of psilocin. Therefore, PCG can be considered to be more stable than the labile psilocin and should always be included if psilocin is analyzed in samples.

  20. Aqueous fractionation of biomass based on novel carbohydrate hydrolysis kinetics

    DOEpatents

    Torget, Robert W.

    2001-01-01

    A multi-function process for hydrolysis and fractionation of lignocellulosic biomass to separate hemicellulosic sugars from other biomass components comprising extractives and proteins; a portion of a solubilized lignin; cellulose; glucose derived from cellulose; and insoluble lignin from said biomass comprising: a) introducing either solid fresh biomass or partially fractioned lignocellulosic biomass material with entrained acid or water into a reactor and heating to a temperature of up to about 185.degree. C.-205.degree. C. b) allowing the reaction to proceed to a point where about 60% of the hemicellulose has been hydrolyzed in the case of water or complete dissolution in case of acid; c) adding a dilute acid liquid at a pH below about 5 at a temperature of up to about 205.degree. C. for a period ranging from about 5 to about 10 minutes; to hydrolyze the remaining 40% of hemicellulose if water is used. d) quenching the reaction at a temperature of up to about 140.degree. C. to quench all degradation and hydrolysis reactions; and e) introducing into said reaction chamber and simultaneously removing from said reaction chamber, a volumetric flow rate of dilute acid at a temperature of up to about 140.degree. C. to wash out the majority of the solubilized biomass components, to obtain improved hemicellosic sugar yields.