Science.gov

Sample records for acid solutions resulted

  1. Reactivity of Hontomín carbonate rocks to acidic solution injection: reactive "push-pull" tracer tests results

    NASA Astrophysics Data System (ADS)

    De Gaspari, Francesca; Cabeza, Yoar; Luquot, Linda; Rötting, Tobias; Saaltink, Maarten W.; Carrera, Jesus

    2014-05-01

    Several field tests will be carried out in order to characterize the reservoir for CO2 injection in Hontomín (Burgos, Spain) as part of the Compostilla project of "Fundación Ciudad de la Energía" (CIUDEN). Once injected, the dissolution of the CO2 in the resident brine will increase the acidity of the water and lead to the dissolution of the rocks, constituted mainly by carbonates. This mechanism will cause changes in the aquifer properties such as porosity and permeability. To reproduce the effect of the CO2 injection, a reactive solution with 2% of acetic acid is going to be injected in the reservoir and extracted from the same well (reactive "push-pull" tracer tests) to identify and quantify the geochemical reactions occurring into the aquifer. The reactivity of the rock will allow us also to evaluate the changes of its properties. Previously, theoretical calculations of Damkhöler numbers were done to determine the acid concentrations and injection flow rates needed to generate ramified-wormholes patterns, during theses "push-pull" experiments. The aim of this work is to present the results and a preliminary interpretation of the field tests.

  2. Soil-solution partitioning of DOC in acid organic soils: Results from a UK field acidification and alkalization experiment

    NASA Astrophysics Data System (ADS)

    Oulehle, Filip; Jones, Timothy; Burden, Annette; Evans, Chris

    2013-04-01

    Dissolved organic carbon (DOC) is an important component of the global carbon (C) cycle and has profound impacts on water chemistry and metabolism in lakes and rivers. Reported increases of DOC concentration in surface waters across Europe and Northern America have been attributed to several drivers; from changing climate and land-use to eutrophication and declining acid deposition. The last of these suggests that acidic deposition suppressed the solubility of DOC, and that this historic suppression is now being reversed by reducing emissions of acidifying pollutants. We studied a set of four parallel acidification and alkalization experiments in organic rich soils which, after three years of manipulation, have shown clear soil solution DOC responses to acidity change. We tested whether these DOC concentration changes were related to changes in the acid/base properties of DOC. Based on laboratory determination of DOC site density (S.D. = amount of carboxylic groups per milligram DOC) and charge density (C.D. = organic acid anion concentration per milligram DOC) we found that the change in DOC soil-solution partitioning was tightly related to the change in degree of dissociation (α = C.D./S.D. ratio) of organic acids (R2=0.74, p<0.01). Carbon turnover in soil organic matter (SOM), determined by soil respiration and β-D-glucosidase enzyme activity measurements, also appears to have some impact on DOC leaching, via constraints on the actual supply of available DOC from SOM; when the turnover rate of C in SOM is low, the effect of α on DOC leaching is reduced. Thus, differences in the magnitude of DOC changes seen across different environments might be explained by interactions between physicochemical restrictions of DOC soil-solution partitioning, and SOM carbon turnover effects on DOC supply.

  3. High resolution electrochemical STM : new structural results for underpotentially deposited Cu on Au(111) in acid sulfate solution.

    SciTech Connect

    Sieradzki, Karl; Vasiljevic, Natasa; Viyannalage, L.K.T.; Dimitrov, Nikolay

    2007-09-01

    Adsorption of sulfate assists Cu monolayer underpotential deposition (upd) on Au(111) in a unique way, rendering two distinct structural stages: (i) formation of a low-density Cu phase at coverage of 2/3 ML known as the ({radical}3 x {radical}3) R30{sup o} or honeycomb phase; (ii) formation of a complete monolayer, i.e., Cu-(1 x 1) phase pseudomorphic with respect to underlying Au(111) substrate. In this paper we present new structural in situ scanning tunneling microscopy (STM) results for this system. We show and discuss the STM imaging of the copper honeycomb superstructure probed underneath the co-adsorbed ({radical}3 x {radical}3)R30{sup o} sulfate adlayer in the low-density phase. High resolution imaging during the phase transition from the low to high density copper phase unambiguously shows the existence of an ordered sulfate structure p(2 x 2) on the pseudomorphic Cu-(1 x 1) layer. The new structure is seen during the co-existence of two copper phases as well as upon completion of the Cu-(1 x 1) monolayer. While supported by earlier chronocoulometric measurements in the same system, the new structural results raise questions that need to be addressed in a future work.

  4. CONDUCTIVITY TITRATION OF GELATIN SOLUTIONS WITH ACIDS.

    PubMed

    Hitchcock, D I

    1923-11-20

    Titrations have been made, by the conductivity method, of gelatin solutions with hydrochloric and sulphuric acids. The results indicate an end-point at about 8.6 cc. of N/10 acid per gm. of gelatin, or a combining weight of about 1,160. These results are in fair agreement with those previously obtained by the hydrogen electrode method. Better agreement between the two methods was found in the case of deaminized gelatin. The data are in accord with a purely chemical conception of the combination between protein and acid.

  5. Process for defoaming acid gas scrubbing solutions and defoaming solutions

    SciTech Connect

    Ernst, E.R.; Robbins, M.L.

    1980-06-17

    The foam in acid gas scrubbing solutions created during an acid gas scrubbing process is reduced or eliminated by the addition of certain polyoxyethylene polyoxypropylene block copolymers as defoaming agents. The defoaming agents are particularly effective when the acid gas scrubbing solution contains an amine having a large hydrophobic moiety.

  6. Electrical conductivity of acidic sulfate solution

    NASA Astrophysics Data System (ADS)

    Majima, Hiroshi; Peters, Ernest; Awakura, Yasuhiro; Park, Sung Kook

    1987-03-01

    The electrical conductivities of the aqueous solution system of H2SO4-MSO4 (involving ZnSO4, MgSO4, Na2SO4, and (NH4)2SO4), reported by Tozawa et al., were examined in terms of a (H2O) and H+ ion concentration. The equations to compute the concentrations of various species in aqueous sulfuric acid solutions containing metal sulfates were derived for a typical example of the H2SO4-ZnSO4-MgSO4-(Na2SO4)-H2O system. It was found that the H+ ion concentrations in concentrated sulfuric acid solutions corresponding to practical zinc electrowinning solutions are very high and remain almost constant with or without the addition of metal sulfates. The addition of metal sulfates to aqueous sulfuric acid solution causes a decrease in electrical conductivity, and this phenomenon is attributed to a decrease in water activity, which reflects a decrease in the amount of free water. The relationship between conductivity and water activity at a constant H+ ion concentration is independent of the kind of sulfates added. On the other hand, any increase in H+ ion concentration results in an increase in electrical conductivity. A novel method for the prediction of electrical conductivity of acidic sulfate solution is proposed that uses the calculated data of water activity and the calculated H+ ion concentration. Also, the authors examined an extension of the Robinson-Bower equation to calculate water activity in quarternary solutions based on molarity instead of molality, and found that such calculated values are in satisfactory agreement with those determined experimentally by a transpiration method.

  7. ELECTROLYTIC REDUCTION OF NITRIC ACID SOLUTIONS

    DOEpatents

    Alter, H.W.; Barney, D.L.

    1958-09-30

    A process is presented for the treatment of radioactivc waste nitric acid solutions. The nitric acid solution is neutralized with an alkali metal hydroxide in an amount sufficient to precipitate insoluble hydroxides, and after separation of the precipitate the solution is electrolyzed to convert the alkali nitrate formed, to alkali hydroxide, gaseous ammonla and oxygen. The solution is then reusable after reducing the volume by evaporating the water and dissolved ammonia.

  8. Nitric acid recovery from waste solutions

    DOEpatents

    Wilson, A. S.

    1959-04-14

    The recovery of nitric acid from aqueous nitrate solutions containing fission products as impurities is described. It is desirable to subject such solutions to concentration by evaporation since nitric acid is regenerated thereby. A difficulty, however, is that the highly radioactive fission product ruthenium is volatilized together with the nitric acid. It has been found that by adding nitrous acid, ruthenium volatilization is suppressed and reduced to a negligible degree so that the distillate obtained is practically free of ruthenium.

  9. Speciation in aqueous solutions of nitric acid.

    PubMed

    Hlushak, S; Simonin, J P; De Sio, S; Bernard, O; Ruas, A; Pochon, P; Jan, S; Moisy, P

    2013-02-28

    In this study, speciation in aqueous solutions of nitric acid at 25 °C was assessed in two independent ways. First, Raman experiments were carried out and interpreted in terms of free nitrate ions, ion pairs and neutral HNO(3) molecules. In parallel, a model was developed to account for the formation of these two kinds of pairs. It was based on an extension of the binding mean spherical approximation (BiMSA), or associative MSA (AMSA), in which the size and the charge of the ions in the chemical pair may differ from those of the free ions. A simultaneous fit of the osmotic coefficient and of the proportion of free ions (obtained from Raman spectroscopy experiments) led to an estimation of the speciation in nitric acid solutions. The result obtained using this procedure was compared with the estimation obtained from the Raman experiments.

  10. Solution nonideality related to solute molecular characteristics of amino acids.

    PubMed Central

    Keener, C R; Fullerton, G D; Cameron, I L; Xiong, J

    1995-01-01

    By measuring the freezing-point depression for dilute, aqueous solutions of all water-soluble amino acids, we test the hypothesis that nonideality in aqueous solutions is due to solute-induced water structuring near hydrophobic surfaces and solute-induced water destructuring in the dipolar electric fields generated by the solute. Nonideality is expressed with a single solute/solvent interaction parameter I, calculated from experimental measure of delta T. A related parameter, I(n), gives a method of directly relating solute characteristics to solute-induced water structuring or destructuring. I(n)-values correlate directly with hydrophobic surface area and inversely with dipolar strength. By comparing the nonideality of amino acids with progressively larger hydrophobic side chains, structuring is shown to increase with hydrophobic surface area at a rate of one perturbed water molecule per 8.8 square angstroms, implying monolayer coverage. Destructuring is attributed to dielectric realignment as described by the Debye-Hückel theory, but with a constant separation of charges in the amino-carboxyl dipole. By using dimers and trimers of glycine and alanine, this destructuring is shown to increase with increasing dipole strength using increased separation of fixed dipolar charges. The capacity to predict nonideal solution behavior on the basis of amino acid characteristics will permit prediction of free energy of transfer to water, which may help predict the energetics of folding and unfolding of proteins based on the characteristics of constituent amino acids. Images FIGURE 6 PMID:7711253

  11. Reactive solute transport in acidic streams

    USGS Publications Warehouse

    Broshears, R.E.

    1996-01-01

    Spatial and temporal profiles of Ph and concentrations of toxic metals in streams affected by acid mine drainage are the result of the interplay of physical and biogeochemical processes. This paper describes a reactive solute transport model that provides a physically and thermodynamically quantitative interpretation of these profiles. The model combines a transport module that includes advection-dispersion and transient storage with a geochemical speciation module based on MINTEQA2. Input to the model includes stream hydrologic properties derived from tracer-dilution experiments, headwater and lateral inflow concentrations analyzed in field samples, and a thermodynamic database. Simulations reproduced the general features of steady-state patterns of observed pH and concentrations of aluminum and sulfate in St. Kevin Gulch, an acid mine drainage stream near Leadville, Colorado. These patterns were altered temporarily by injection of sodium carbonate into the stream. A transient simulation reproduced the observed effects of the base injection.

  12. Reference electrode for strong oxidizing acid solutions

    DOEpatents

    Rigdon, Lester P.; Harrar, Jackson E.; Bullock, Sr., Jack C.; McGuire, Raymond R.

    1990-01-01

    A reference electrode for the measurement of the oxidation-reduction potentials of solutions is especially suitable for oxidizing solutions such as highly concentrated and fuming nitric acids, the solutions of nitrogen oxides, N.sub.2 O.sub.4 and N.sub.2 O.sub.5, in nitric acids. The reference electrode is fabricated of entirely inert materials, has a half cell of Pt/Ce(IV)/Ce(III)/70 wt. % HNO.sub.3, and includes a double-junction design with an intermediate solution of 70 wt. % HNO.sub.3. The liquid junctions are made from Corning No. 7930 glass for low resistance and negligible solution leakage.

  13. Precipitation of plutonium from acidic solutions using magnesium oxide

    SciTech Connect

    Jones, S.A.

    1994-12-05

    Magnesium oxide will be used as a neutralizing agent for acidic plutonium-containing solutions. It is expected that as the magnesium oxide dissolves, the pH of the solution will rise, and plutonium will precipitate. The resulting solid will be tested for suitability to storage. The liquid is expected to contain plutonium levels that meet disposal limit requirements.

  14. Polymerization of beta-amino acids in aqueous solution

    NASA Technical Reports Server (NTRS)

    Liu, R.; Orgel, L. E.; Bada, J. L. (Principal Investigator)

    1998-01-01

    We have compared carbonyl diimidazole (CDI) and 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDAC) as activating agents for the oligomerization of negatively-charged alpha- and beta-amino acids in homogeneous aqueous solution. alpha-Amino acids can be oligomerized efficiently using CDI, but not by EDAC. beta-Amino acids can be oligomerized efficiently using EDAC, but not by CDI. Aspartic acid, an alpha- and beta-dicarboxylic acid is oligomerized efficiently by both reagents. These results are explained in terms of the mechanisms of the reactions, and their relevance to prebiotic chemistry is discussed.

  15. Alkaline earth cation extraction from acid solution

    DOEpatents

    Dietz, Mark; Horwitz, E. Philip

    2003-01-01

    An extractant medium for extracting alkaline earth cations from an aqueous acidic sample solution is described as are a method and apparatus for using the same. The separation medium is free of diluent, free-flowing and particulate, and comprises a Crown ether that is a 4,4'(5')[C.sub.4 -C.sub.8 -alkylcyclohexano]18-Crown-6 dispersed on an inert substrate material.

  16. Wet oxidation of salicylic acid solutions.

    PubMed

    Collado, Sergio; Garrido, Laura; Laca, Adriana; Diaz, Mario

    2010-11-15

    Salicylic acid is a frequent pollutant in several industrial wastewaters. Uncatalyzed wet air oxidation, which is a promising technique for the treatment of phenolic effluents, has not been analyzed yet for the removal of salicylic acid. The effect of different conditions of pH (1.3-12.3), pressure (1.0-4.1 MPa), temperature (413-443 K), and initial concentrations (1.45-14.50 mM) on the wet oxidation of salicylate/salicylic acid solutions have here been investigated. The pH value of the reaction media was found to be a key parameter for the rate of the oxidation process with an optimum at pH 3.1, when the concentrations of salicylic acid and salicylate were similar. The oxidation reaction followed pseudofirst-order kinetics with respect to salicylic acid and 0.82 order with respect to dissolved oxygen. Additionally, the evolution of the color during the wet oxidation was analyzed and discussed in relation with the formation of intermediate compounds. Then, a reaction pathway for the noncatalytic wet oxidation of the salicylic acid was proposed.

  17. REMOVAL OF CHLORIDE FROM ACIDIC SOLUTIONS USING NO2

    SciTech Connect

    Visser, A; Robert Pierce, R; James Laurinat, J

    2006-08-22

    Chloride (Cl{sup -}) salt processing in strong acids is used to recycle plutonium (Pu) from pyrochemical residues. The Savannah River National Laboratory (SRNL) is studying the potential application of nitrogen dioxide (NO{sub 2}) gas to effectively convert dissolved pyrochemical salt solutions to chloride-free solutions and improve recovery operations. An NO{sub 2} sparge has been shown to effectively remove Cl{sup -} from solutions containing 6-8 M acid (H{sup +}) and up to 5 M Cl{sup -}. Chloride removal occurs as a result of the competition of at least two reactions, one which is acid-dependent. Below 4 M H+, NO2 reacts with Cl- to produce nitrosyl chloride (ClNO). Between 6 M and 8 M H{sup +}, the reaction of hydrochloric acid (HCl) with nitric acid (HNO{sub 3}), facilitated by the presence of NO{sub 2}, strongly affects the rate of Cl{sup -} removal. The effect of heating the acidic Cl{sup -} salt solution without pre-heating the NO{sub 2} gas has minimal effect on Cl{sup -} removal rates when the contact times between NO{sub 2} and the salt solution are on the order of seconds.

  18. Pictorial Analogies XI: Concentrations and Acidity of Solutions.

    ERIC Educational Resources Information Center

    Fortman, John J.

    1994-01-01

    Presents pictorial analogies of several concepts relating to solutions for chemistry students. These include concentration of solution, strength of solution, supersaturated solution, and conjugate acid-base pairs. Among the examples are comparison of acid strength to percentage of strong soldiers or making supersaturated solution analogous to a…

  19. Acidities of Water and Methanol in Aqueous Solution and DMSO

    ERIC Educational Resources Information Center

    Gao, Daqing

    2009-01-01

    The relative acidities of water and methanol have been a nagging issue. In gas phase, methanol is more acidic than water by 36.0 kJ/mol; however, in aqueous solution, the acidities of methanol and water are almost identical. The acidity of an acid in solution is determined by both the intrinsic gas-phase ionization Gibbs energy and the solvent…

  20. Does Nitric Acid Dissociate at the Aqueous Solution Surface?

    SciTech Connect

    Lewis, Tanza; Winter, Berndt; Stern, Abraham C.; Baer, Marcel D.; Mundy, Christopher J.; Tobias, Douglas J.; Hemminger, J. C.

    2011-11-03

    Nitric acid is a prevalent component of atmospheric aerosols, and the extent of nitric acid dissociation at aqueous interfaces is relevant to its role in heterogeneous atmospheric chemistry. Several experimental and theoretical studies have suggested that the extent of dissociation of nitric acid near aqueous interfaces is less than in bulk solution. Here, dissociation of HNO3 at the surface of aqueous nitric acid is quantified using X-ray photoelectron spectroscopy of the nitrogen local electronic structure. The relative amounts of undissociated HNO3(aq) and dissociated NO3-(aq) are identified by the distinguishable N1s core-level photoelectron spectra of the two species, and we determine the degree of dissociation, αint, in the interface (the first ~3 layers of solution) as a function of HNO3 concentration. Our measurements show that dissociation is decreased by approximately 20% near the solution interface compared with bulk, and furthermore that dissociation occurs even in the top-most solution layer. The experimental results are supported by first-principles MD simulations, which show that hydrogen-bonds between HNO3 and water molecules at the solution surface stabilize the molecular form at low concentration, in analogy to the stabilization of molecular HNO3 that occurs in bulk solution at high concentration. This work was supported by the U.S. Department of Energy's (DOE) Office of Basic Energy Sciences, Chemical Sciences program. The Pacific Northwest National Laboratory is operated by Battelle for DOE.

  1. Radiolysis of aqueous solutions of 2-aminoethanethiosulfuric acid. [Gamma radiation

    SciTech Connect

    Grachev, S.A.; Koroleva, I.K.; Kropachev, E.V.; Litvyakova, G.I.

    1982-07-10

    In the radiolysis products of aerated and deaerated solutions of the 2-aminoethanethiosulfuric acid the authors have identified cystamine monoxide, cystamine, taurine, mercamine, the sulfate ion, the sulfite ion, and the dithionate ion. The yields of these products under different conditions have been determined. Results indicated that the sulfate ion is formed both from the divalent and the hexavalent sulfur atom of the 2-aminoethanethiosulfuric acid moelcule. A possible radiolysis mechanism is discussed.

  2. Dephosphorization of Steelmaking Slag by Leaching with Acidic Aqueous Solution

    NASA Astrophysics Data System (ADS)

    Qiao, Yong; Diao, Jiang; Liu, Xuan; Li, Xiaosa; Zhang, Tao; Xie, Bing

    2015-12-01

    In the present paper, dephosphorization of steelmaking slag by leaching with acidic aqueous solution composed of citric acid, sodium hydroxide, hydrochloric acid and ion-exchanged water was investigated. The buffer solution of C6H8O7-NaOH-HCl system prevented changes in the pH values. Kinetic parameters including leaching temperature, slag particle size and pH values of the solution were optimized. The results showed that temperature has no obvious effect on the dissolution ratio of phosphorus. However, it has a significant effect on the dissolution ratio of iron. The dephosphorization rate increases with the decrease of slag particle size and the pH value of the solution. Over 90% of the phosphorus can be dissolved in the solution while the corresponding leaching ratio of iron was only 30% below the optimal condition. Leaching kinetics of dephosphorization follow the unreacted shrinking core model with a rate controlled step by the solid diffusion layer, the corresponding apparent activation energy being 1.233 kJ mol-1. A semiempirical kinetic equation was established. After leaching, most of the nC2S-C3P solid solution in the steelmaking slag was selectively dissolved in the aqueous solution and the iron content in the solid residue was correspondingly enriched.

  3. Dephosphorization of Steelmaking Slag by Leaching with Acidic Aqueous Solution

    NASA Astrophysics Data System (ADS)

    Qiao, Yong; Diao, Jiang; Liu, Xuan; Li, Xiaosa; Zhang, Tao; Xie, Bing

    2016-09-01

    In the present paper, dephosphorization of steelmaking slag by leaching with acidic aqueous solution composed of citric acid, sodium hydroxide, hydrochloric acid and ion-exchanged water was investigated. The buffer solution of C6H8O7-NaOH-HCl system prevented changes in the pH values. Kinetic parameters including leaching temperature, slag particle size and pH values of the solution were optimized. The results showed that temperature has no obvious effect on the dissolution ratio of phosphorus. However, it has a significant effect on the dissolution ratio of iron. The dephosphorization rate increases with the decrease of slag particle size and the pH value of the solution. Over 90% of the phosphorus can be dissolved in the solution while the corresponding leaching ratio of iron was only 30% below the optimal condition. Leaching kinetics of dephosphorization follow the unreacted shrinking core model with a rate controlled step by the solid diffusion layer, the corresponding apparent activation energy being 1.233 kJ mol-1. A semiempirical kinetic equation was established. After leaching, most of the nC2S-C3P solid solution in the steelmaking slag was selectively dissolved in the aqueous solution and the iron content in the solid residue was correspondingly enriched.

  4. Process for the extraction of strontium from acidic solutions

    DOEpatents

    Horwitz, E. Philip; Dietz, Mark L.

    1994-01-01

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid.

  5. Process for the extraction of strontium from acidic solutions

    DOEpatents

    Horwitz, E.P.; Dietz, M.L.

    1993-01-01

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid.

  6. Process for the extraction of strontium from acidic solutions

    DOEpatents

    Horwitz, E.P.; Dietz, M.L.

    1994-09-06

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid. 4 figs.

  7. NAPAP (National Acid Precipitation Assessment Program) results on acid rain

    SciTech Connect

    Not Available

    1990-06-01

    The National Acid Precipitation Assessment Program (NAPAP) was mandated by Congress in 1980 to study the effects of acid rain. The results of 10 years of research on the effect of acid deposition and ozone on forests, particularly high elevation spruce and fir, southern pines, eastern hardwoods and western conifers, will be published this year.

  8. Methanol Uptake by Low Temperature Aqueous Sulfuric Acid Solutions

    NASA Technical Reports Server (NTRS)

    Iraci, L. T.; Essin, A. M.; Golden, D. M.; Hipskind, R. Stephen (Technical Monitor)

    2001-01-01

    The global methanol budget is currently unbalanced, with source terms significantly larger than the sinks terms. To evaluate possible losses of gaseous methanol to sulfate aerosols, the solubility and reactivity of methanol in aqueous sulfuric acid solutions representative of upper tropospheric and lower stratospheric aerosols is under investigation. Methanol will partition into sulfate aerosols according to its Henry's law solubility. Using standard uptake techniques in a Knudsen cell reactor, we have measured the effective Henry's law coefficient, H*, for cold (196 - 220 K) solutions ranging between 45 and 70 wt % H2SO4. We have found that methanol solubility ranges from approx. 10(exp 5) - 10(exp 7) M/atm for UT/LS conditions. Solubility increases with decreasing temperature and with increasing sulfuric acid content. Although methanol is slightly more soluble than are acetone and formaldehyde, current data indicate that uptake by clean aqueous sulfuric acid particles will not be a significant sink for methanol in the UT/LS. These solubility measurements include uptake due to physical solvation and any rapid equilibria which are established in solution. Reaction between primary alcohols and sulfuric acid does occur, leading to the production of alkyl sulfates. Literature values for the rate of this reaction suggest that formation of CH3OSO3H is not significant over our experimental time scale for solutions below 80 wt % H2SO4. To confirm this directly, results obtained using a complementary equilibrium measurement technique will also be presented.

  9. Nylon Dissolution in Nitric Acid Solutions

    SciTech Connect

    KESSINGER, GLENF.

    2004-06-16

    H Area Operations is planning to process Pu-contaminated uranium scrap in support of de-inventory efforts. Nylon bags will be used to hold materials to be dissolved in H-Canyon. Based on this set of twelve nylon dissolutions, it is concluded that (when other variables are held constant): increased acid concentration results in increased dissolution rates; increased acid concentration results in a lower dissolution onset temperature; little, if any, H plus is consumed during the depolymerization process; and 2.0-3.0 M HNO3, with 0.025 M KF and 2 g/L B, is satisfactory for the dissolution of nylon bag materials to be used during H-Canyon processing.

  10. Nitric acid uptake by sulfuric acid solutions under stratospheric conditions - Determination of Henry's Law solubility

    NASA Technical Reports Server (NTRS)

    Reihs, Christa M.; Golden, David M.; Tolbert, Margaret A.

    1990-01-01

    The uptake of nitric acid by sulfuric acid solutions representative of stratospheric particulate at low temperatures was measured to determine the solubility of nitric acid in sulfuric acid solutions as a function of H2SO4 concentration and solution temperature. Solubilities are reported for sulfuric acid solutions ranging from 58 to 87 wt pct H2SO4 over a temperature range from 188 to 240 K, showing that, in general, the solubility of nitric acid increases with decreasing sulfuric acid concentration and with decreasing temperature. The measured solubilities indicate that nitric acid in the global stratosphere will be found predominantly in the gas phase.

  11. An ellipsometric study of mild steel in hydrochloric acid solutions

    NASA Astrophysics Data System (ADS)

    Brakenbury, W. R. E.; Grzeskowiak, R.

    1986-04-01

    An ellipsometric study has been made on mild steel in hydrochloric acid solutions, in a situation where film growth is not expected. The results are considered to be due to roughening and have been interpreted in terms of a Fenstermaker-McCrackin type roughening model. It appears that the ellipsometer is sensitive mainly to a small scale roughening consisting of etch pits of a few nanometers in dimensions rather than the larger roughened features easily seen by microscopic examination.

  12. Effect of phytic acid, ethylenediaminetetraacetic acid, and chitosan solutions on microhardness of the human radicular dentin

    PubMed Central

    Nikhil, Vineeta; Jaiswal, Shikha; Bansal, Parul; Arora, Rohit; Raj, Shalya; Malhotra, Pulkit

    2016-01-01

    Aim: The purpose of this study was to evaluate the effect of phytic acid, ethylenediaminetetraacetic acid (EDTA), and chitosan solutions on the microhardness of human radicular dentin. Materials and Methods: Thirty dentin specimens were randomly divided into three groups of 10 specimens each according to the irrigant used: G1 — 1% phytic acid, G2 — 17% EDTA, and G3 — 0.2% chitosan. A standardized volume of each chelating solution was used for 3 min. Dentin microhardness was measured before and after application at the cervical, middle, and apical levels with a Vickers indenter under a 200-g load and a 10-s dwell time. The results were analyzed using one-way analysis of variance (ANOVA) and Student's t test. Results: Microhardness of the radicular dentin varied at the cervical, middle, and apical levels. EDTA had the greatest overall effect, causing a sharp percentage reduction in dentin microhardness with a significant difference from phytic acid and chitosan (P = 0.002). However, phytic acid and chitosan differed insignificantly from each other (P = 0.887). Conclusion: All tested chelating solutions reduced microhardness of the radicular dentin layer at all the levels. However, reduction was least at the apical level. EDTA caused more reduction in dentin microhardness than chitosan while phytic acid reduced the least. PMID:27099428

  13. Methanol Uptake By Low Temperature Aqueous Sulfuric Acid Solutions

    NASA Technical Reports Server (NTRS)

    Iraci, Laura T.; Essin, Andrew M.; Golden, David M.; Hipskind, R. Stephen (Technical Monitor)

    2001-01-01

    To evaluate the role of upper tropospheric and lower stratospheric aerosols in the global budget of methanol, the solubility and reactivity of CH3OH in aqueous sulfuric acid solutions are under investigation. Using standard uptake techniques in a Knudsen cell reactor, we have measured the effective Henry's law coefficient, H(*), for methanol dissolution into 45 to 70 percent by weight H2SO4. We find that methanol solubility ranges from 10(exp 5) to 10(exp 8) M/atm and increases with decreasing temperature and with increasing sulfuric acid content. These solubility measurements include uptake due to physical solvation and all rapid equilibria which are established in solution. Our data indicate that simple uptake by aqueous sulfuric acid particles will not be a significant sink for methanol in the UT/LS. These results differ from those recently reported in the literature, and an explanation of this disparity will be presented. In addition to solvation, reaction between primary alcohols and sulfuric acid does occur, leading to the production of alkyl sulfates. Literature values for the rate of this reaction suggest that formation of CH3OSO3H may proceed in the atmosphere but is not significant under our experimental conditions. Results obtained using a complementary equilibrium measurement technique confirm this directly. In addition, the extent of methanol sequestration via formation of mono- and dimethylsulfate will be evaluated under several atmospheric conditions.

  14. Process for the recovery of strontium from acid solutions

    DOEpatents

    Horwitz, E. Philip; Dietz, Mark L.

    1992-01-01

    The invention is a process for selectively extracting strontium and technetium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant is a macrocyclic polyether in a diluent which is insoluble in water, but which will itself dissolve a small amount of water. The process will extract strontium and technetium values from nitric acid solutions which are up to 6 molar in nitric acid.

  15. Process for the recovery of strontium from acid solutions

    DOEpatents

    Horwitz, E.P.; Dietz, M.L.

    1992-03-31

    The invention is a process for selectively extracting strontium and technetium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant is a macrocyclic polyether in a diluent which is insoluble in water, but which will itself dissolve a small amount of water. The process will extract strontium and technetium values from nitric acid solutions which are up to 6 molar in nitric acid. 5 figs.

  16. Process for the recovery of strontium from acid solutions

    SciTech Connect

    Horwitz, E.P.; Dietz, M.L.

    1990-12-31

    The invention is a process for selectively extracting strontium and technetium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant is a macrocyclic polyether in a diluent which is insoluble in water, but which will itself dissolve a small amount of water. The process will extract strontium and technetium values from nitric acid solutions which are up to 6 molar in nitric acid.

  17. REDUCTION OF ACIDITY OF NITRIC ACID SOLUTIONS BY USE OF FORMALDEHYDE

    DOEpatents

    Healy, T.V.

    1958-05-20

    A continuous method is described of concentrating by evaporation and reducing the nitrate ion content of an aqueous solution of metallic salts containing nitric acid not in excess of 8N. It consists of heating the solution and then passing formaldehyde into the heated solution to bring about decomposition of the nitric acid. The evolved gases containing NO are contacted countercurrently with an aqueous metal salt solution containing nitric acid in excess of 8N so as to bring about decomposition of the nitric acid and lower the normality to at least 8N, whereupon it is passed into the body of heated solution.

  18. Method for liquid chromatographic extraction of strontium from acid solutions

    DOEpatents

    Horwitz, E. Philip; Dietz, Mark L.

    1992-01-01

    A method and apparatus for extracting strontium and technetium values from biological, industrial and environmental sample solutions using a chromatographic column is described. An extractant medium for the column is prepared by generating a solution of a diluent containing a Crown ether and dispersing the solution on a resin substrate material. The sample solution is highly acidic and is introduced directed to the chromatographic column and strontium or technetium is eluted using deionized water.

  19. Toluene nitration in irradiated nitric acid and nitrite solution

    SciTech Connect

    Gracy Elias; Bruce J. Mincher; Stephen P. Mezyk; Jim Muller; Leigh R. Martin

    2011-04-01

    The kinetics, mechanisms, and stable products produced for the aryl alkyl mild ortho-para director - toluene, in irradiated nitric acid and neutral nitrite solutions were investigated using ?, and pulse radiolysis. Electron pulse radiolysis was used to determine the bimolecular rate constants for the reaction of toluene with different transient species produced by irradiation. HPLC with UV detection was primarily used to assess the stable reaction products. GC-MS and LC-MS were used to confirm the results from HPLC. Free-radical nitration reaction products were found in irradiated acidic and neutral media. In acidic medium, the ring substitution and side chain substitution and oxidation produced different nitro products. In ring substitution, nitrogen oxide radicals were added mainly to hydroxyl radical-produced cyclohexadienyl radical, and in side chain substitution they were added to the carbon-centered benzyl radical produced by H-atom abstraction. In neutral nitrite toluene solution, radiolytic ring nitration products approached a statistically random distribution, suggesting a free-radical reaction involving addition of the •NO2 radical.

  20. Corrosion of dental amalgams in solutions of organic acids.

    PubMed

    Palaghias, G

    1986-06-01

    A conventional and two high copper amalgams were tested in 0.5% aqueous solutions of acetic, formic, lactic and succinic acid. The corrosion behavior of the amalgams in the different solutions was evaluated by analyzing the soluble corrosion products using an atomic absorption spectrophotometer every month during a 6-month experimental period. The high copper amalgams showed a high dissolution rate in formic and lactic acid solutions from the initial stages of immersion when compared to the conventional. Later a marked decrease of the dissolution rate could be observed but it still remained at high levels. In acetic acid the amounts of elements dissolved from high copper amalgams were much less. Conventional amalgam released much smaller amounts of elements in almost all solutions tested except in the case of silver in lactic acid. Finally, in succinic acid solution, the amounts of elements dissolved were unexpectedly small considering the low pH of the solution and the dissolution rates of the amalgams in the other organic acid solutions. PMID:3461548

  1. Effect of citric acid on the acidification of artificial pepsin solution for metacercariae isolation from fish.

    PubMed

    Kim, Min-Ki; Pyo, Kyoung-Ho; Hwang, Young-Sang; Chun, Hyang Sook; Park, Ki Hwan; Ko, Seong-Hee; Chai, Jong-Yil; Shin, Eun-Hee

    2013-11-15

    Artificial digestive solution based on pepsin is essential for collecting metacercariae from fish. To promote the enzymatic reactivity of pepsin, the pH of the solution has to be adjusted to pH 1.0-2.0. Hydrochloride (HCl) is usually used for this purpose, but the use of HCl raises safety concerns. The aim of this work was to address the usefulness of citric acid as an alternative for HCl for the acidification of pepsin solution, and to examine its potential to damage metacercariae during in vitro digestion as compared with HCl. Changes in pH after adding 1-9% of citric acid (m/v) to pepsin solution were compared to a 1% HCl (v/v) addition. Digestion of fish muscle was evaluated by measuring released protein concentrations by spectrophotometry. In addition, survival rates of metacercariae in pepsin solution were determined at different citric acid concentrations and were compared that of with 1% HCl. The present study shows that addition of citric acid reduced the pH of pepsin solutions to the required level. Addition of more than 5% of citric acid resulted in the effective digestion of fish muscle over 3h in vitro, and 5% citric acid was less lethal to metacercariae than 1% HCl in pepsin solution. Pepsin solution containing 5% citric acid had digestive capacity superior to pepsin solution containing 1% HCl after 3h incubation with released protein concentrations of 12.0 ng/ml for 5% citric acid and 9.6 ng/ml for 1% HCl. Accordingly, the present study suggests that the addition of 5% citric acid to pepsin solution is a good alternative to 1% HCl in infection studies because citric acid is a stable at room temperature and has a good safety profile. In addition, we suggest that the use of citric acid enables the preparation of commercial digestive solutions for the detection of microorganisms in fish and other vertebrate muscle tissue.

  2. Extraction equilibrium of indium(III) from nitric acid solutions by di(2-ethylhexyl)phosphoric acid dissolved in kerosene.

    PubMed

    Tsai, Hung-Sheng; Tsai, Teh-Hua

    2012-01-04

    The extraction equilibrium of indium(III) from a nitric acid solution using di(2-ethylhexyl) phosphoric acid (D2EHPA) as an acidic extractant of organophosphorus compounds dissolved in kerosene was studied. By graphical and numerical analysis, the compositions of indium-D2EHPA complexes in organic phase and stoichiometry of the extraction reaction were examined. Nitric acid solutions with various indium concentrations at 25 °C were used to obtain the equilibrium constant of InR₃ in the organic phase. The experimental results showed that the extraction distribution ratios of indium(III) between the organic phase and the aqueous solution increased when either the pH value of the aqueous solution and/or the concentration of the organic phase extractant increased. Finally, the recovery efficiency of indium(III) in nitric acid was measured.

  3. Decomposition Studies of Triphenylboron, Diphenylborinic Acid and Phenylboric Acid in Aqueous Alkaline Solutions Containing Copper

    SciTech Connect

    Crawford, C.L.; Peterson, R. A.

    1997-02-11

    This report documents the copper-catalyzed chemical kinetics of triphenylboron, diphenylborinic acid and phenylboric acid (3PB, 2PB and PBA) in aqueous alkaline solution contained in carbon-steel vessels between 40 and 70 degrees C.

  4. Vacuum-jacketed hydrofluoric acid solution calorimeter

    USGS Publications Warehouse

    Robie, R.A.

    1965-01-01

    A vacuum-jacketed metal calorimeter for determining heats of solution in aqueous HF was constructed. The reaction vessel was made of copper and was heavily gold plated. The calorimeter has a cooling constant of 0.6 cal-deg -1-min-1, approximately 1/4 that of the air-jacketed calorimeters most commonly used with HF. It reaches equilibrium within 10 min after turning off the heater current. Measurements of the heat of solution of reagent grade KCl(-100 mesh dried 2 h at 200??C) at a mole ratio of 1 KCl to 200 H2O gave ??H = 4198??11 cal at 25??C. ?? 1965 The American Institute of Physics.

  5. Raman spectra of amino acids and their aqueous solutions

    NASA Astrophysics Data System (ADS)

    Zhu, Guangyong; Zhu, Xian; Fan, Qi; Wan, Xueliang

    2011-03-01

    Amino acids are the basic "building blocks" that combine to form proteins and play an important physiological role in all life-forms. Amino acids can be used as models for the examination of the importance of intermolecular bonding in life processes. Raman spectra serve to obtain information regarding molecular conformation, giving valuable insights into the topology of more complex molecules (peptides and proteins). In this paper, amino acids and their aqueous solution have been studied by Raman spectroscopy. Comparisons of certain values for these frequencies in amino acids and their aqueous solutions are given. Spectra of solids when compared to those of the solute in solution are invariably much more complex and almost always sharper. We present a collection of Raman spectra of 18 kinds of amino acids ( L-alanine, L-arginine, L-aspartic acid, cystine, L-glutamic acid, L-glycine, L-histidine, L-isoluecine, L-leucine, L-lysine, L-phenylalanine, L-methionone, L-proline, L-serine, L-threonine, L-tryptophan, L-tyrosine, L-valine) and their aqueous solutions that can serve as references for the interpretation of Raman spectra of proteins and biological materials.

  6. Improved method for extracting lanthanides and actinides from acid solutions

    DOEpatents

    Horwitz, E.P.; Kalina, D.G.; Kaplan, L.; Mason, G.W.

    1983-07-26

    A process for the recovery of actinide and lanthanide values from aqueous acidic solutions uses a new series of neutral bi-functional extractants, the alkyl(phenyl)-N,N-dialkylcarbamoylmethylphosphine oxides. The process is suitable for the separation of actinide and lanthanide values from fission product values found together in high-level nuclear reprocessing waste solutions.

  7. Method for incorporating radioactive phosphoric acid solutions in concrete

    DOEpatents

    Wolf, Gary A [Kennewick, WA; Smith, Jeffrey W [Lancaster, OH; Ihle, Nathan C [Walla Walla, WA

    1984-01-01

    A method for incorporating radioactive phosphoric acid solutions in concrete is described wherein the phosphoric acid is reacted with Ca(OH).sub.2 to form a precipitate of hydroxyapatite and the hydroxyapatite is mixed with portland cement to form concrete.

  8. Method for incorporating radioactive phosphoric acid solutions in concrete

    DOEpatents

    Wolf, G.A.; Smith, J.W.; Ihle, N.C.

    1982-07-08

    A method for incorporating radioactive phosphoric acid solutions in concrete is described wherein the phosphoric acid is reacted with Ca(OH)/sub 2/ to form a precipitate of hydroxyapatite and the hydroxyapatite is mixed with Portland cement to form concrete.

  9. Phosphorylation of glyceric acid in aqueous solution using trimetaphosphate.

    PubMed

    Kolb, V; Orgel, L E

    1996-02-01

    The phosphorylation of glyceric acid is an interesting prebiotic reaction because it converts a simple, potentially prebiotic organic molecule into phosphate derivatives that are central to carbohydrate metabolism. We find that 0.05 M glyceric acid in the presence of 0.5 M trimetaphosphate in alkaline solution gives a mixture of 2- and 3-phosphoglyceric acids in combined yields of up to 40%. PMID:11536746

  10. Phosphorylation of Glyceric Acid in Aqueous Solution Using Trimetaphosphate

    NASA Technical Reports Server (NTRS)

    Kolb, Vera; Orgel, Leslie E.

    1996-01-01

    The phosphorylation of glyceric acid is an interesting prebiotic reaction because it converts a simple, potentially prebiotic organic molecule into phosphate derivatives that are central to carbohydrate metabolism. We find that 0.05 M glyceric acid in the presence of 0.5 M trimetaphosphate in alkaline solution gives a mixture of 2- and 3-phosphoglyceric acids in combined yields of up to 40%.

  11. Reduction of Plutonium in Acidic Solutions by Mesoporous Carbons

    DOE PAGES

    Parsons-Moss, Tashi; Jones, Stephen; Wang, Jinxiu; Wu, Zhangxiong; Uribe, Eva; Zhao, Dongyuan; Nitsche, Heino

    2015-12-19

    Batch contact experiments with several porous carbon materials showed that carbon solids spontaneously reduce the oxidation state of plutonium in 1-1.5 M acid solutions, without significant adsorption. The final oxidation state and rate of Pu reduction varies with the solution matrix, and also depends on the surface chemistry and surface area of the carbon. It was demonstrated that acidic Pu(VI) solutions can be reduced to Pu(III) by passing through a column of porous carbon particles, offering an easy alternative to electrolysis with a potentiostat.

  12. Reduction of hexavalent chromium by ascorbic acid in aqueous solutions.

    PubMed

    Xu, Xiang-Rong; Li, Hua-Bin; Li, Xiao-Yan; Gu, Ji-Dong

    2004-11-01

    Hexavalent chromium is a priority pollutant in the USA and many other countries. Reduction of Cr(VI) to Cr(III) is environmentally favorable as the latter species is not toxic to most living organisms and also has a low mobility and bioavailability. Reduction of Cr(VI) by ascorbic acid (vitamin C) as a reductant was studied using potassium dichromate solution as the model pollutant. Effects of concentration of vitamin C, pH, temperature, irradiation and reaction time on the reduction of Cr(VI) were examined. Cr(VI) might be reduced by vitamin C not only in acidic conditions but also in weakly alkaline solutions. The reduction of Cr(VI) by vitamin C might occur not only under irradiation but also in the dark. Vitamin C is an important biological reductant in humans and animals, and not toxic. It is water-soluble and can easily permeate through various types of soils. The results indicate that vitamin C could be used in effective remediation of Cr(VI)-contaminated soils and groundwater in a wide range of pH, with or without sunlight. PMID:15488923

  13. Reduction of hexavalent chromium by ascorbic acid in aqueous solutions.

    PubMed

    Xu, Xiang-Rong; Li, Hua-Bin; Li, Xiao-Yan; Gu, Ji-Dong

    2004-11-01

    Hexavalent chromium is a priority pollutant in the USA and many other countries. Reduction of Cr(VI) to Cr(III) is environmentally favorable as the latter species is not toxic to most living organisms and also has a low mobility and bioavailability. Reduction of Cr(VI) by ascorbic acid (vitamin C) as a reductant was studied using potassium dichromate solution as the model pollutant. Effects of concentration of vitamin C, pH, temperature, irradiation and reaction time on the reduction of Cr(VI) were examined. Cr(VI) might be reduced by vitamin C not only in acidic conditions but also in weakly alkaline solutions. The reduction of Cr(VI) by vitamin C might occur not only under irradiation but also in the dark. Vitamin C is an important biological reductant in humans and animals, and not toxic. It is water-soluble and can easily permeate through various types of soils. The results indicate that vitamin C could be used in effective remediation of Cr(VI)-contaminated soils and groundwater in a wide range of pH, with or without sunlight.

  14. Sorption of acid red 57 from aqueous solution onto sepiolite.

    PubMed

    Alkan, Mahir; Demirbaş, Ozkan; Celikçapa, Sermet; Doğan, Mehmet

    2004-12-10

    Sepiolite, a highly porous mineral, is becoming widely used as an alternative material in areas where sorptive, catalytic and rheological applications are required. High ion exchange capacity and high surface area and more importantly its relatively cheap price make it an attractive adsorbent. In this study, the adsorption of acid red 57 by natural mesoporous sepiolite has been examined in order to measure the ability of this mineral to remove coloured textile dyes from wastewater. For this purpose, a series of batch adsorption tests of acid red 57 from aqueous sepiolite solutions have been systematically investigated as a function of parameters such as pH, ionic strength and temperature. Adsorption equilibrium was reached within 1h. The removal of acid red 57 decreases with pH from 3 to 9 and temperature from 25 to 55 degrees C, whereas it increases with ionic strength from 0 to 0.5 mol L(-1). Adsorption isotherms of acid red on sepiolite were determined and correlated with common isotherm equations such as Langmuir and Freundlich models. It was found that the Langmuir model appears to fit the isotherm data better than the Freundlich model. The physical properties of this adsorbent were consistent with the parameters obtained from the isotherm equations. Approximately, 21.49% weight loss was observed. The surface area value of sepiolite was 342 m2 g(-1) at 105 degrees C, and it increased to 357 m2 g(-1) at 200 degrees C. Further increase in temperature caused channel plugging and crystal structure deformation, as a result the surface area values showed a decrease with temperature. The data obtained from adsorption isotherms at different temperatures have been used to calculate some thermodynamic quantities such as the Gibbs energy, heat and entropy of adsorption. The thermodynamic data indicate that acid red 57 adsorption onto sepiolite is characterized by physical adsorption. The dimensionless separation factor (RL) have shown that sepiolite can be used for

  15. Solubility of xenon in amino-acid solutions. II. Nine less-soluble amino acids

    NASA Astrophysics Data System (ADS)

    Kennan, Richard P.; Himm, Jeffrey F.; Pollack, Gerald L.

    1988-05-01

    Ostwald solubility (L) of xenon gas, as the radioisotope 133Xe, has been measured as a function of solute concentration, at 25.0 °C, in aqueous solutions of nine amino acids. The amino-acid concentrations investigated covered much of their solubility ranges in water, viz., asparagine monohydrate (0-0.19 M), cysteine (0-1.16 M), glutamine (0-0.22 M), histidine (0-0.26 M), isoleucine (0-0.19 M), methionine (0-0.22 M), serine (0-0.38 M), threonine (0-1.4 M), and valine (0-0.34 M). We have previously reported solubility results for aqueous solutions of six other, generally more soluble, amino acids (alanine, arginine, glycine, hydroxyproline, lysine, and proline), of sucrose and sodium chloride. In general, L decreases approximately linearly with increasing solute concentration in these solutions. If we postulate that the observed decreases in gas solubility are due to hydration, the results under some assumptions can be used to calculate hydration numbers (H), i.e., the number of H2O molecules associated with each amino-acid solute molecule. The average values of hydration number (H¯) obtained at 25.0 °C are 15.3±1.5 for asparagine, 6.8±0.3 for cysteine, 11.5±1.1 for glutamine, 7.3±0.7 for histidine, 5.9±0.4 for isoleucine, 10.6±0.8 for methionine, 11.2±1.3 for serine, 7.7± 1.0 for threonine, and 6.6±0.6 for valine. We have also measured the temperature dependence of solubility L(T) from 5-40 °C for arginine, glycine, and proline, and obtained hydration numbers H¯(T) in this range. Between 25-40 °C, arginine has an H¯ near zero. This may be evidence for an attractive interaction between xenon and arginine molecules in aqueous solution.

  16. Adaptation of sweeteners in water and in tannic acid solutions.

    PubMed

    Schiffman, S S; Pecore, S D; Booth, B J; Losee, M L; Carr, B T; Sattely-Miller, E; Graham, B G; Warwick, Z S

    1994-03-01

    Repeated exposure to a tastant often leads to a decrease in magnitude of the perceived intensity; this phenomenon is termed adaptation. The purpose of this study was to determine the degree of adaptation of the sweet response for a variety of sweeteners in water and in the presence of two levels of tannic acid. Sweetness intensity ratings were given by a trained panel for 14 sweeteners: three sugars (fructose, glucose, sucrose), two polyhydric alcohols (mannitol, sorbitol), two terpenoid glycosides (rebaudioside-A, stevioside), two dipeptide derivatives (alitame, aspartame), one sulfamate (sodium cyclamate), one protein (thaumatin), two N-sulfonyl amides (acesulfame-K, sodium saccharin), and one dihydrochalcone (neohesperidin dihydrochalcone). Panelists were given four isointense concentrations of each sweetener by itself and in the presence of two concentrations of tannic acid. Each sweetener concentration was tasted and rated four consecutive times with a 30 s interval between each taste and a 2 min interval between each concentration. Within a taste session, a series of concentrations of a given sweetener was presented in ascending order of magnitude. Adaptation was calculated as the decrease in intensity from the first to the fourth sample. The greatest adaptation in water solutions was found for acesulfame-K, Na saccharin, rebaudioside-A, and stevioside. This was followed by the dipeptide sweeteners, alitame and aspartame. The least adaptation occurred with the sugars, polyhydric alcohols, and neohesperidin dihydrochalcone. Adaptation was greater in tannic acid solutions than in water for six sweeteners. Adaptation of sweet taste may result from the desensitization of sweetener receptors analogous to the homologous desensitization found in the beta adrenergic system.

  17. γ-Irradiation of malic acid in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Negron-Mendoza, Alicia; Graff, Rebecca L.; Ponnamperuma, Cyril

    1980-12-01

    The γ-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the non-volatile products. Thin layer chromotography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the γ-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

  18. Release of nitrous acid and nitrogen dioxide from nitrate photolysis in acidic aqueous solutions.

    PubMed

    Scharko, Nicole K; Berke, Andrew E; Raff, Jonathan D

    2014-10-21

    Nitrate (NO3(-)) is an abundant component of aerosols, boundary layer surface films, and surface water. Photolysis of NO3(-) leads to NO2 and HONO, both of which play important roles in tropospheric ozone and OH production. Field and laboratory studies suggest that NO3¯ photochemistry is a more important source of HONO than once thought, although a mechanistic understanding of the variables controlling this process is lacking. We present results of cavity-enhanced absorption spectroscopy measurements of NO2 and HONO emitted during photodegradation of aqueous NO3(-) under acidic conditions. Nitrous acid is formed in higher quantities at pH 2-4 than expected based on consideration of primary photochemical channels alone. Both experimental and modeled results indicate that the additional HONO is not due to enhanced NO3(-) absorption cross sections or effective quantum yields, but rather to secondary reactions of NO2 in solution. We find that NO2 is more efficiently hydrolyzed in solution when it is generated in situ during NO3(-) photolysis than for the heterogeneous system where mass transfer of gaseous NO2 into bulk solution is prohibitively slow. The presence of nonchromophoric OH scavengers that are naturally present in the environment increases HONO production 4-fold, and therefore play an important role in enhancing daytime HONO formation from NO3(-) photochemistry.

  19. Comparison of peak shape in hydrophilic interaction chromatography using acidic salt buffers and simple acid solutions.

    PubMed

    Heaton, James C; Russell, Joseph J; Underwood, Tim; Boughtflower, Robert; McCalley, David V

    2014-06-20

    The retention and peak shape of neutral, basic and acidic solutes was studied on hydrophilic interaction chromatography (HILIC) stationary phases that showed both strong and weak ionic retention characteristics, using aqueous-acetonitrile mobile phases containing either formic acid (FA), ammonium formate (AF) or phosphoric acid (PA). The effect of organic solvent concentration on the results was also studied. Peak shape was good for neutrals under most mobile phase conditions. However, peak shapes for ionised solutes, particularly for basic compounds, were considerably worse in FA than AF. Even neutral compounds showed deterioration in performance with FA when the mobile phase water concentration was reduced. The poor performance in FA cannot be entirely attributed to the negative impact of ionic retention on ionised silanols on the underlying silica base materials, as results using PA at lower pH (where their ionisation is suppressed) were inferior to those in AF. Besides the moderating influence of the salt cation on ionic retention, it is likely that salt buffers improve peak shape due to the increased ionic strength of the mobile phase and its impact on the formation of the water layer on the column surface.

  20. Highly accurate boronimeter assay of concentrated boric acid solutions

    SciTech Connect

    Ball, R.M. )

    1992-01-01

    The Random-Walk Boronimeter has successfully been used as an on-line indicator of boric acid concentration in an operating commercial pressurized water reactor. The principle has been adapted for measurement of discrete samples to high accuracy and to concentrations up to 6000 ppm natural boron in light water. Boric acid concentration in an aqueous solution is a necessary measurement in many nuclear power plants, particularly those that use boric acid dissolved in the reactor coolant as a reactivity control system. Other nuclear plants use a high-concentration boric acid solution as a backup shutdown system. Such a shutdown system depends on rapid injection of the solution and frequent surveillance of the fluid to ensure the presence of the neutron absorber. The two methods typically used to measure boric acid are the chemical and the physical methods. The chemical method uses titration to determine the ionic concentration of the BO[sub 3] ions and infers the boron concentration. The physical method uses the attenuation of neutrons by the solution and infers the boron concentration from the neutron absorption properties. This paper describes the Random-Walk Boronimeter configured to measure discrete samples to high accuracy and high concentration.

  1. Temperature dependence of hydrogen-bond dynamics in acetic acid-water solutions.

    PubMed

    D'Amico, Francesco; Bencivenga, Filippo; Gessini, Alessandro; Masciovecchio, Claudio

    2010-08-19

    An inelastic UV scattering experiment has been carried out on acetic acid-water solutions as a function of temperature and concentration. The analysis of experimental data indicates the presence of a crossover temperature (T(c) approximately 325 +/- 10 K). Above T(c), the energy of hydrogen bonds responsible for water-acetic acid and acetic acid-acetic acid interactions is strongly reduced. This leads to a reduction in the average number of water molecule interacting with acetic acid, as well as to a lower number of acetic acid clusters. The latter behavior can be mainly ascribed to a temperature change in the activation energy of carboxylic groups of acetic acid. These results may be also relevant to better understand the folding mechanism in protein-water solutions. PMID:20701390

  2. Unsaturated fatty acids in alkane solution: adsorption to steel surfaces.

    PubMed

    Lundgren, Sarah M; Persson, Karin; Mueller, Gregor; Kronberg, Bengt; Clarke, Jim; Chtaib, Mohammed; Claesson, Per M

    2007-10-01

    The adsorption of the unsaturated fatty acids oleic, linoleic, and linolenic acid on steel surfaces has been investigated by means of a quartz crystal microbalance (QCM). Two different solvents were used, n-hexadecane and its highly branched isomer, viz., 2,2,4,4,6,8,8-heptamethylnonane. The area occupied per molecule of oleic acid at 1 wt % corresponds to what is needed for adsorption parallel to the surface. At the same concentration, the adsorbed amount of linoleic acid and linolenic acid indicates that they adsorb in multilayers. The chemisorbed amount estimated from static secondary ion mass spectroscopy (SIMS) measurements was found to be similar for the three unsaturated fatty acids. In the case of linolenic acid, it was found that the presence of water significantly alters the adsorption, most likely because of the precipitation of fatty acid/water aggregates. Furthermore, static SIMS results indicate that the amount of water used here inhibits the chemisorption of linolenic acid.

  3. The Solubility of Xenon in Simple Organic Solvents and in Aqueous Amino Acid Solutions.

    NASA Astrophysics Data System (ADS)

    Himm, Jeffrey Frank

    We have measured the Ostwald solubility (L) of ('133)Xe in a variety of liquids, including normal alkanes, normal alkanols, and aqueous solutions of amino acids, NaCl, and sucrose. For the alkanes and alkanols, measurements were made in the temperature range from 10-50(DEGREES)C. Values of L were found to decrease with increasing temperature, and also with increasing chain length, for both series of solvents. Thermodynamic properties of solution (enthalpy and entropy of solution) are calculated using both mole fraction and number density scales. Results are interpreted using Uhlig's model of the solvation process. Measurements of L in aqueous amino acid solutions were made at 25(DEGREES)C. Concentrations of amino acids in solution varied from near saturation for each of the amino acids studied to pure water. In all solutions, except those with NaCl, L decreases linearly with increasing solution molarity. Hydration numbers (H), the mean number of water molecules associated with each solute molecule, were determined for each amino acid, for NaCl, and for sucrose. Values of H obtained ranged from near zero (arginine, H = 0.2 (+OR-) 0.5) to about 16 (NaCl, H = 16.25 (+OR-) 0.3).

  4. Mechanistic studies of nitrations and oxidations in solutions of dinitrogen pentaoxide in nitric acid

    SciTech Connect

    Willmer, R.F.

    1992-01-01

    Mechanisms of nitrations in solutions of dinitrogen pentaoxide in nitric acid of 1,2,4-trichloro-5-nitrobenzene and 1,2-dichloro-4-nitrobenzene have been proposed. The kinetics and products of the nitration, in the title medium, of substantially deactivated benzoic acids and benzaldehydes have been investigated. Kinetics of nitration of some substituted benzoic acids in nitric acid solutions containing dinitrogen pentaoxide or nitronium trifluoro-methanesulphonate (nitronium triflate) have been compared. Rate coefficients for reactions in dinitrogen pentaoxide solutions were generally similar to those from nitronium triflate solutions of the same estimated nitronium ion concentration. Yields of aromatic products of nitration of some benzoic acid derivatives in the nitric acid solutions have been determined. Nitrodecarboxylation of 4-fluorobenzoic acid occurs as a result of nitronium ion attach at C(1). The competition between oxidation to the corresponding benzoic acid and nitration in the aromatic ring of some substituted benzaldehydes has been probed by kinetic and product studies. 4-Carboxybenzaldehyde is nitrated but more deactivated substrates are predominantly oxidized. Rapid reversible gem-dinitrate formation occurs in concentrated dinitrogen pentaoxide solutions. The equilibrium extent of formation of [alpha]-deuterio-(4-nitropheny)-dinitratomethane from [alpha]-deuterio-4-nitrobenzaldehyde is reported. 4-nitrobenzaldehyde and the gem-dinitrate are oxidized in processes in which [alpha]-hydrogen loss is at least partially rate determining. The relative rates of oxidation in nitronium triflate solutions suggest that the [alpha]-hydrogen is removed as a hydride ion in that medium. There is evidence for the intrusion of a radical mechanism of nitration in concentrated solutions of dinitrogen pentaoxide. (4-Nitrophenyl)dinitratomethane was produced on the addition of 4-nitrobenzaldehyde to a solution of dinitrogen pentaoxide in dichloromethane.

  5. Solution properties and taste behavior of lactose monohydrate in aqueous ascorbic acid solutions at different temperatures: Volumetric and rheological approach.

    PubMed

    Sarkar, Abhijit; Sinha, Biswajit

    2016-11-15

    The densities and viscosities of lactose monohydrate in aqueous ascorbic acid solutions with several molal concentrations m=(0.00-0.08)molkg(-1) of ascorbic acid were determined at T=(298.15-318.15)K and pressure p=101kPa. Using experimental data apparent molar volume (ϕV), standard partial molar volume (ϕV(0)), the slope (SV(∗)), apparent specific volumes (ϕVsp), standard isobaric partial molar expansibility (ϕE(0)) and its temperature dependence [Formula: see text] the viscosity B-coefficient and solvation number (Sn) were determined. Viscosity B-coefficients were further employed to obtain the free energies of activation of viscous flow per mole of the solvents (Δμ1(0≠)) and of the solute (Δμ2(0≠)). Effects of molality, solute structure and temperature and taste behavior were analyzed in terms of solute-solute and solute-solvent interactions; results revealed that the solutions are characterized predominantly by solute-solvent interactions and lactose monohydrate behaves as a long-range structure maker. PMID:27283672

  6. Thermodynamic and Ultrasonic Properties of Ascorbic Acid in Aqueous Protic Ionic Liquid Solutions

    PubMed Central

    Singh, Vickramjeet; Sharma, Gyanendra; Gardas, Ramesh L.

    2015-01-01

    In this work, we report the thermodynamic and ultrasonic properties of ascorbic acid (vitamin C) in water and in presence of newly synthesized ammonium based protic ionic liquid (diethylethanolammonium propionate) as a function of concentration and temperature. Apparent molar volume and apparent molar isentropic compression, which characterize the solvation state of ascorbic acid (AA) in presence of protic ionic liquid (PIL) has been determined from precise density and speed of sound measurements at temperatures (293.15 to 328.15) K with 5 K interval. The strength of molecular interactions prevailing in ternary solutions has been discussed on the basis of infinite dilution partial molar volume and partial molar isentropic compression, corresponding volume of transfer and interaction coefficients. Result has been discussed in terms of solute-solute and solute-solvent interactions occurring between ascorbic acid and PIL in ternary solutions (AA + water + PIL). PMID:26009887

  7. Process for recovering uranium using an alkyl pyrophosphoric acid and alkaline stripping solution

    SciTech Connect

    Worthington, R.E.; Magdics, A.

    1987-03-24

    A process is described for stripping uranium for a pregnant organic extractant comprising an alkyl pyrophosphoric acid dissolved in a substantially water-immiscible organic diluent. The organic extractant contains tetravalent uranium and an alcohol or phenol modifier in a quantity sufficient to retain substantially all the unhydrolyzed alkyl pyrophosphoric acid in solution in the diluent during stripping. The process comprises adding an oxidizing agent to the organic extractant and thereby oxidizing the tetravalent uranium to the +6 state in the organic extractant, and contacting the organic extractant containing the uranium in the +6 state with a stripping solution comprising an aqueous solution of an alkali metal or ammonium carbonate or hydroxide thereby stripping uranium from the organic extractant into the stripping solution. The resulting barren organic extractant containing substantially all of the unhydrolyzed alkyl pyrophosphoric acid dissolved in the diluent is separated from the stripping solution containing the stripped uranium, the barren extractant being suitable for recycle.

  8. Process for recovering uranium using an alkyl pyrophosphoric acid and alkaline stripping solution

    SciTech Connect

    Worthington, R.E.; Magdics, A.

    1987-03-24

    A process is described for stripping uranium from a pregnant organic extractant comprising an alkyl pyrophosphoric acid dissolved in a substantially water-immiscible organic diluent. The organic extractant contains tetravalent uranium and an alcohol or phenol modifier in a quantity sufficient to retain substantially all the unhydrolyzed alkyl pyrophosphoric acid in solution in the diluent during stripping. The process comprises adding an oxidizing agent to the organic extractant to and thereby oxidizing the tetravalent uranium to the +6 state in the organic extractant, and contacting the organic extractant containing the uranium in the +6 state with a stripping solution comprising an aqueous solution of an alkali metal or ammonium carbonate, nonsaturated in uranium. The uranium is stripped from, the organic extractant into the stripping solution, and the resulting barren organic extractant containing substantially all of the unhydrolyzed alkyl pyrophosphoric acid dissolved in the diluent is separated from the stripping solution containing the stripped uranium, the barren extractant being suitable for recycle.

  9. The dissolution of quartz in dilute aqueous solutions of organic acids at 25 degree C

    SciTech Connect

    Bennett, P.C.; Melcer, M.E.; Siegel, D.I.; Hassett, J.P. )

    1988-06-01

    The dissolution of quartz in dilute aqueous solutions of organic acids at 25{degree}C and standard pressure was investigated by the batch dissolution method. The bulk dissolution rate of quartz in 20 mmole/Kg citrate solutions at pH 7 was 8 to 10 times faster than that in pure water. After 1750 hours the concentration of dissolved silica in the citrate solution was 167 {mu}mole/Kg compared to 50 {mu}mole/Kg in water and a 20 mmole/Kg solution of acetate at pH 7. Solutions of salicylic, oxalic, and humic acids also accelerated the dissolution of quartz in aqueous solution at pH 7. The rate of dissolution in organic acids decreased sharply with decreasing pH. The possibility of a silica-organic acid complex was investigated using UV-difference spectroscopy. Results suggest that dissolved silica is complexed by citrate, oxalate and pyruvate at pH 7 by an electron-donor acceptor complex, whereas no complexation occurs between silica and acetate, lactate, malonate, or succinate. Three models are proposed for the solution and surface complexation of silica by organic acid which result in the accelerated dissolution and increased solubility of quartz in organic rich water.

  10. The dissolution of quartz in dilute aqueous solutions of organic acids at 25°C

    NASA Astrophysics Data System (ADS)

    Bennett, P. C.; Melcer, M. E.; Siegel, D. I.; Hassett, J. P.

    1988-06-01

    The dissolution of quartz in dilute aqueous solutions of organic acids at 25° and standard pressure was investigated by the batch dissolution method. The bulk dissolution rate of quartz in 20 mmole/Kg citrate solutions at pH 7 was 8 to 10 times faster than that in pure water. After 1750 hours the concentration of dissolved silica in the citrate solution was 167 μmole/Kg compared to 50 μmole/Kg in water and a 20 mmole/Kg solution of acetate at pH 7. Solutions of salicylic, oxalic, and humic acids also accelerated the dissolution of quartz in aqueous solution at pH 7. The rate of dissolution in organic acids decreased sharply with decreasing pH. The possibility of a silica-organic acid complex was investigated using UV-difference spectroscopy. Results suggest that dissolved silica is complexed by citrate, oxalate and pyruvate at pH 7 by an electron-donor acceptor complex, whereas no complexation occurs between silica and acetate, lactate, malonate, or succinate. Three models are proposed for the solution and surface complexation of silica by organic acid anions which result in the accelerated dissolution and increased solubility of quartz in organic rich water.

  11. Antimicrobial and cytotoxic effects of phosphoric acid solution compared to other root canal irrigants

    PubMed Central

    PRADO, Maíra; da SILVA, Emmanuel João Nogueira Leal; DUQUE, Thais Mageste; ZAIA, Alexandre Augusto; FERRAZ, Caio Cezar Randi; de ALMEIDA, José Flávio Affonso; GOMES, Brenda Paula Figueiredo de Almeida

    2015-01-01

    Phosphoric acid has been suggested as an irrigant due to its effectiveness in removing the smear layer. Objectives : The purpose of this study was to compare the antimicrobial and cytotoxic effects of a 37% phosphoric acid solution to other irrigants commonly used in endodontics. Material and Methods : The substances 37% phosphoric acid, 17% EDTA, 10% citric acid, 2% chlorhexidine (solution and gel), and 5.25% NaOCl were evaluated. The antimicrobial activity was tested against Candida albicans, Staphylococcus aureus, Enterococcus faecalis, Escherichia coli, Actinomyces meyeri, Parvimonas micra, Porphyromonas gingivalis, and Prevotella nigrescens according to the agar diffusion method. The cytotoxicity of the irrigants was determined by using the MTT assay. Results : Phosphoric acid presented higher antimicrobial activity compared to the other tested irrigants. With regard to the cell viability, this solution showed results similar to those with 5.25% NaOCl and 2% chlorhexidine (gel and solution), whereas 17% EDTA and 10% citric acid showed higher cell viability compared to other irrigants. Conclusion : Phosphoric acid demonstrated higher antimicrobial activity and cytotoxicity similar to that of 5.25% NaOCl and 2% chlorhexidine (gel and solution). PMID:26018307

  12. SAVANNAH RIVER SITE TANK CLEANING: CORROSION RATE FOR ONE VERSUS EIGHT PERCENT OXALIC ACID SOLUTION

    SciTech Connect

    Ketusky, E.; Subramanian, K.

    2011-01-20

    Until recently, the use of oxalic acid for chemically cleaning the Savannah River Site (SRS) radioactive waste tanks focused on using concentrated 4 and 8-wt% solutions. Recent testing and research on applicable dissolution mechanisms have concluded that under appropriate conditions, dilute solutions of oxalic acid (i.e., 1-wt%) may be more effective. Based on the need to maximize cleaning effectiveness, coupled with the need to minimize downstream impacts, SRS is now developing plans for using a 1-wt% oxalic acid solution. A technology gap associated with using a 1-wt% oxalic acid solution was a dearth of suitable corrosion data. Assuming oxalic acid's passivation of carbon steel was proportional to the free oxalate concentration, the general corrosion rate (CR) from a 1-wt% solution may not be bound by those from 8-wt%. Therefore, after developing the test strategy and plan, the corrosion testing was performed. Starting with the envisioned process specific baseline solvent, a 1-wt% oxalic acid solution, with sludge (limited to Purex type sludge-simulant for this initial effort) at 75 C and agitated, the corrosion rate (CR) was determined from the measured weight loss of the exposed coupon. Environmental variations tested were: (a) Inclusion of sludge in the test vessel or assuming a pure oxalic acid solution; (b) acid solution temperature maintained at 75 or 45 C; and (c) agitation of the acid solution or stagnant. Application of select electrochemical testing (EC) explored the impact of each variation on the passivation mechanisms and confirmed the CR. The 1-wt% results were then compared to those from the 8-wt%. The immersion coupons showed that the maximum time averaged CR for a 1-wt% solution with sludge was less than 25-mils/yr for all conditions. For an agitated 8-wt% solution with sludge, the maximum time averaged CR was about 30-mils/yr at 50 C, and 86-mils/yr at 75 C. Both the 1-wt% and the 8-wt% testing demonstrated that if the sludge was removed from

  13. Characterization of metal ion-nucleic acid interactions in solution.

    PubMed

    Pechlaner, Maria; Sigel, Roland K O

    2012-01-01

    Metal ions are inextricably involved with nucleic acids due to their polyanionic nature. In order to understand the structure and function of RNAs and DNAs, one needs to have detailed pictures on the structural, thermodynamic, and kinetic properties of metal ion interactions with these biomacromolecules. In this review we first compile the physicochemical properties of metal ions found and used in combination with nucleic acids in solution. The main part then describes the various methods developed over the past decades to investigate metal ion binding by nucleic acids in solution. This includes for example hydrolytic and radical cleavage experiments, mutational approaches, as well as kinetic isotope effects. In addition, spectroscopic techniques like EPR, lanthanide(III) luminescence, IR and Raman as well as various NMR methods are summarized. Aside from gaining knowledge about the thermodynamic properties on the metal ion-nucleic acid interactions, especially NMR can be used to extract information on the kinetics of ligand exchange rates of the metal ions applied. The final section deals with the influence of anions, buffers, and the solvent permittivity on the binding equilibria between metal ions and nucleic acids. Little is known on some of these aspects, but it is clear that these three factors have a large influence on the interaction between metal ions and nucleic acids.

  14. RESULTS FROM THE MOUNTAIN ACID DEPOSITION PROGRAM

    EPA Science Inventory

    The Mountain Acid Deposition Program (MADPro) was initiated in 1993 as part of the research necessary to support the objectives of the Clean Air Status and Trends Network (CASTNet), which was created to address the. requirements of the Clean Air Act Amendments (CAAA). The main ob...

  15. Effects of peroxyacetic acid, acidified sodium chlorite or lactic acid solutions on the microflora of chilled beef carcasses.

    PubMed

    Gill, C O; Badoni, M

    2004-02-15

    The effects of solutions of 0.02% peroxyacetic acid, acidified 0.16% sodium chlorite, 2% lactic acid and 4% lactic acid on the natural flora of the distal surfaces of pieces of brisket, from chilled beef carcass quarters delivered from two slaughtering plants to a processing plant, were investigated. Peroxyacetic acid and acidified sodium chlorite solutions had little effect on the numbers of aerobes, coliforms or Escherichia coli on meat from one plant, and were less effective than 4% lactic acid for reducing the numbers of bacteria on meat from the other plant. With meat from both plants, treatment of meat with 4% lactic acid and holding for 5 or 60 min at 7+/-1 degrees C before sampling resulted in reductions of all three groups of bacteria by >/=1.5 log unit. Treatment with 2% lactic acid resulted in similar reductions when meat was sampled 5 min after the treatment, but reductions were about 1 log unit when meat was sampled 60 min after the treatment. Treatment of carcass quarters with 4% lactic acid resulted in reductions of bacterial numbers of >/=2 log units at distal surfaces, but solutions may be inconsistent when they are applied to chilled meat from different sources and to different types of meat surface, and that bacteria injured by application of an antimicrobial solution may recover during processing of meat at temperatures about 7 degrees C. However, 4% lactic acid may be generally useful as a decontaminant for chilled, raw meat. PMID:14967559

  16. Environment and solute-solvent interaction effects on photo-physical behaviors of Folic acid and Folinic acid drugs

    NASA Astrophysics Data System (ADS)

    Khadem Sadigh, M.; Zakerhamidi, M. S.; Seyed Ahmadian, S. M.; Johari-Ahar, M.; Zare Haghighi, L.

    2016-12-01

    In this paper, spectral properties of Folic acid and Folinic acid as widely used drugs in the treatment of some diseases have been studied in various environments with different polarity. Our results show that the absorption, emission and stokes shifts of solute molecules depend strongly on molecular surrounding characteristics, solute-solvent interactions and, different active groups in their chemical structures. In order to investigate the contribution of specific and nonspecific interactions on various properties of drug samples, the linear solvation energy relationships concept is used. Moreover, the calculated dipole moments by means of solvatochromic method show that the high values of dipole moments in excited state are due to local intramolecular charge transfer. Furthermore, the obtained results about molecular interactions can be extended to biological systems and can indicate completely the behaviors of Folic acid and Folinic acid in polar solvents such as water in body system.

  17. Evaporation kinetics of acetic acid-water solutions

    NASA Astrophysics Data System (ADS)

    Duffey, K.; Wong, N.; Saykally, R.; Cohen, R. C.

    2012-12-01

    The transport of water molecules across vapor-liquid interfaces in the atmosphere is a crucial step in the formation and evolution of cloud droplets. Despite decades of study, the effects of solutes on the mechanism and rate of evaporation and condensation remain poorly characterized. The present work aims to determine the effect of atmospherically-relevant solutes on the evaporation rate of water. In our experiments, we create a train of micron-sized droplets and measure their temperature via Raman thermometry as they undergo evaporation without condensation. Analysis of the cooling rate yields the evaporation coefficient (γ). Previous work has shown that inorganic salts have little effect on γ, with surface-adsorbing anions causing a slight reduction in the coefficient from that measured for pure water. Organic acids are ubiquitous in aqueous aerosol and have been shown to disrupt the surface structure of water. Here we describe measurements of the evaporation rate of acetic acid solutions, showing that acetic acid reduces γ to a larger extent than inorganic ions, and that γ decreases with increasing acetic acid concentration.

  18. Solution Preserves Nucleic Acids in Body-Fluid Specimens

    NASA Technical Reports Server (NTRS)

    Pierson, Duane L.; Stowe, Raymond P.

    2004-01-01

    A solution has been formulated to preserve deoxyribonucleic acid (DNA) and ribonucleic acid (RNA) in specimens of blood, saliva, and other bodily fluids. Specimens of this type are collected for diagnostic molecular pathology, which is becoming the method of choice for diagnosis of many diseases. The solution makes it possible to store such specimens at room temperature, without risk of decomposition, for subsequent analysis in a laboratory that could be remote from the sampling location. Thus, the solution could be a means to bring the benefits of diagnostic molecular pathology to geographic regions where refrigeration equipment and diagnostic laboratories are not available. The table lists the ingredients of the solution. The functions of the ingredients are the following: EDTA chelates divalent cations that are necessary cofactors for nuclease activity. In so doing, it functionally removes these cations and thereby retards the action of nucleases. EDTA also stabilizes the DNA helix. Tris serves as a buffering agent, which is needed because minor contaminants in an unbuffered solution can exert pronounced effects on pH and thereby cause spontaneous degradation of DNA. SDS is an ionic detergent that inhibits ribonuclease activity. SDS has been used in some lysis buffers and as a storage buffer for RNA after purification. The use of the solution is straightforward. For example, a sample of saliva is collected by placing a cotton roll around in the subject's mouth until it becomes saturated, then the cotton is placed in a collection tube. Next, 1.5 mL of the solution are injected directly into the cotton and the tube is capped for storage at room temperature. The effectiveness of the solution has been demonstrated in tests on specimens of saliva containing herpes simplex virus. In the tests, the viral DNA, as amplified by polymerase chain reaction, was detected even after storage for 120 days.

  19. [Results of studying taste sensitivity with basic or pure solutions].

    PubMed

    Marco Algarra, R

    1990-01-01

    In this paper we study the phenomenon of the gustatory fatigue using simple solutions in representation of the four basic-tastes. We have designed a map of the sensibility of the tongue to the four basic tastes according to our results. Finally we study the fatigue and adaptation in the gustatory system, concluding that are different concepts although they are very close related.

  20. Uptake of ozone to mixed sodium bromide/ citric acid solutions

    NASA Astrophysics Data System (ADS)

    Lee, Ming-Tao; Steimle, Emilie; Bartels-Rausch, Thorsten; Kato, Shunsuke; Lampimäki, Markus; Brown, Matthew; van Bokhoven, Jeroen; Nolting, Frithjof; Kleibert, Armin; Türler, Andreas; Ammann, Markus

    2013-04-01

    Sea-salt solution - air interfaces play an important role in the chemistry of the marine boundary layer. The reaction of ozone (O3) with bromide is of interest in the context of formation of photolabile halogens (Br2, BrCl) in the marine boundary layer. Recent experiments have suggested that the bromide oxidation rate is related to the surface concentration of bromide [1] and inversely related to the gas phase concentration of O3, an indication for a precursor mediated reaction at the surface [2]. So far, the effect of organics (such as those occurring at the ocean surface or in marine aerosols) on the reaction of O3 with bromide aerosols has not been studied yet. In our study we investigate the uptake kinetics of O3 to a mixed solution of sodium bromide (NaBr) and citric acid (CA), which represents highly oxidized organic compounds present in the environment, with a well-established coated wall flow tube technique, which leads to exposure of the film to O3 allowing the heterogeneous reactions to take place and the loss of O3 being measured. The results indicate that the uptake of O3 to the films with the higher bromide concentrations (0.34M and 4M) is independent of the gas phase concentration and roughly consistent with uptake limited by reaction in the bulk. For the lower bromide concentration (84mM), however, we observe a trend of the uptake coefficient to decrease with increasing O3 concentration, indicating an increasing importance of a surface reaction. In an attempt to constrain the kinetic data, we employed X-ray photoelectron spectroscopy (XPS) to get insight into the surface composition of the aqueous solution - air interface. Previous XPS studies have shown that halide ion concentrations are enhanced at the aqueous solution air interface [3-4], which likely promotes the surface reactions of bromide or iodide with O3. A first XPS study of ternary solutions of KI with butanol indicated the importance of specific interactions of the cation with the alcohol

  1. Solution influence on biomolecular equilibria - Nucleic acid base associations

    NASA Technical Reports Server (NTRS)

    Pohorille, A.; Pratt, L. R.; Burt, S. K.; Macelroy, R. D.

    1984-01-01

    Various attempts to construct an understanding of the influence of solution environment on biomolecular equilibria at the molecular level using computer simulation are discussed. First, the application of the formal statistical thermodynamic program for investigating biomolecular equilibria in solution is presented, addressing modeling and conceptual simplications such as perturbative methods, long-range interaction approximations, surface thermodynamics, and hydration shell. Then, Monte Carlo calculations on the associations of nucleic acid bases in both polar and nonpolar solvents such as water and carbon tetrachloride are carried out. The solvent contribution to the enthalpy of base association is positive (destabilizing) in both polar and nonpolar solvents while negative enthalpies for stacked complexes are obtained only when the solute-solute in vacuo energy is added to the total energy. The release upon association of solvent molecules from the first hydration layer around a solute to the bulk is accompanied by an increase in solute-solvent energy and decrease in solvent-solvent energy. The techniques presented are expectd to displace less molecular and more heuristic modeling of biomolecular equilibria in solution.

  2. Method for extracting lanthanides and actinides from acid solutions

    DOEpatents

    Horwitz, E. Philip; Kalina, Dale G.; Kaplan, Louis; Mason, George W.

    1985-01-01

    A process for the recovery of actinide and lanthanide values from aqueous acidic solutions with an organic extractant having the formula: ##STR1## where .phi. is phenyl, R.sup.1 is a straight or branched alkyl or alkoxyalkyl containing from 6 to 12 carbon atoms and R.sup.2 is an alkyl containing from 3 to 6 carbon atoms. The process is suitable for the separation of actinide and lanthanide values from fission product values found together in high level nuclear reprocessing waste solutions.

  3. Succinic acid in aqueous solution: connecting microscopic surface composition and macroscopic surface tension.

    PubMed

    Werner, Josephina; Julin, Jan; Dalirian, Maryam; Prisle, Nønne L; Öhrwall, Gunnar; Persson, Ingmar; Björneholm, Olle; Riipinen, Ilona

    2014-10-21

    The water-vapor interface of aqueous solutions of succinic acid, where pH values and bulk concentrations were varied, has been studied using surface sensitive X-ray photoelectron spectroscopy (XPS) and molecular dynamics (MD) simulations. It was found that succinic acid has a considerably higher propensity to reside in the aqueous surface region than its deprotonated form, which is effectively depleted from the surface due to the two strongly hydrated carboxylate groups. From both XPS experiments and MD simulations a strongly increased concentration of the acid form in the surface region compared to the bulk concentration was found and quantified. Detailed analysis of the surface of succinic acid solutions at different bulk concentrations led to the conclusion that succinic acid saturates the aqueous surface at high bulk concentrations. With the aid of MD simulations the thickness of the surface layer could be estimated, which enabled the quantification of surface concentration of succinic acid as a multiple of the known bulk concentration. The obtained enrichment factors were successfully used to model the surface tension of these binary aqueous solutions using two different models that account for the surface enrichment. This underlines the close correlation of increased concentration at the surface relative to the bulk and reduced surface tension of aqueous solutions of succinic acid. The results of this study shed light on the microscopic origin of surface tension, a macroscopic property. Furthermore, the impact of the results from this study on atmospheric modeling is discussed.

  4. DC diaphragm discharge in water solutions of selected organic acids

    NASA Astrophysics Data System (ADS)

    Vyhnankova, Edita J.; Hammer, Malte U.; Reuter, Stephan; Krcma, Frantisek

    2015-07-01

    Effect of four simple organic acids water solution on a DC diaphragm discharge was studied. Efficiency of the discharge was quantified by the hydrogen peroxide production determined by UV-VIS spectrometry of a H2O2 complex formed with specific titanium reagent. Automatic titration was used to study the pH behaviour after the plasma treatment. Optical emission spectroscopy overview spectra were recorded and detailed spectra of OH band and Hβ line were used to calculate the rotational temperature and comparison of the line profile (reflecting electron concentration) in the acid solutions. Contribution to the topical issue "The 14th International Symposium on High Pressure Low Temperature Plasma Chemistry (HAKONE XIV)", edited by Nicolas Gherardi, Ronny Brandenburg and Lars Stollenwark

  5. Interaction of Ethyl Alcohol Vapor with Sulfuric Acid Solutions

    NASA Technical Reports Server (NTRS)

    Leu, Ming-Taun

    2006-01-01

    We investigated the uptake of ethyl alcohol (ethanol) vapor by sulfuric acid solutions over the range approx.40 to approx.80 wt % H2SO4 and temperatures of 193-273 K. Laboratory studies used a fast flow-tube reactor coupled to an electron-impact ionization mass spectrometer for detection of ethanol and reaction products. The uptake coefficients ((gamma)) were measured and found to vary from 0.019 to 0.072, depending upon the acid composition and temperature. At concentrations greater than approx.70 wt % and in dilute solutions colder than 220 K, the values approached approx.0.07. We also determined the effective solubility constant of ethanol in approx.40 wt % H2SO4 in the temperature range 203-223 K. The potential implications to the budget of ethanol in the global troposphere are briefly discussed.

  6. Time dependent inhibition of xanthine oxidase in irradiated solutions of folic acid, aminopterin and methotrexate

    SciTech Connect

    Robinson, K.; Pilot, T.F.; Meany, J.E. )

    1990-01-01

    The xanthine oxidase catalyzed oxidation of hypoxanthine was followed by monitoring the formation of uric acid at 290 nm. Inhibition of xanthine oxidase occurs in aqueous solutions of folic acid methotrexate and aminopterin. These compounds are known to dissociate upon exposure to ultraviolet light resulting in the formation of their respective 6-formylpteridine derivatives. The relative rates of dissociation were monitored spectrophotometrically by determining the absorbance of their 2,4-dinitrophenylhydrazine derivatives at 500 nm. When aqueous solutions of folic acid, aminopterin and methotrexate were exposed to uv light, a direct correlation was observed between the concentrations of the 6-formylpteridine derivatives existing in solution and the ability of these solutions to inhibit xanthine oxidase. The relative potency of the respective photolysis products were estimated.

  7. Dry dilute acid pretreatment by co-currently feeding of corn stover feedstock and dilute acid solution without impregnation.

    PubMed

    He, Yanqing; Zhang, Jian; Bao, Jie

    2014-04-01

    Impregnation of lignocellulose materials with dilute acid solution is a routine operation in conventional dilute acid pretreatment. The dry dilute acid pretreatment (DDAP) at high solids content up to 70% is naturally considered to require longer impregnation time. In this study, a co-currently feeding operation of corn stover and dilute sulfuric acid solution without any impregnation was tested for DDAP. The DDAP pretreated corn stover without impregnation is found to be essentially no difference in pretreatment efficiency compared to those with impregnation in the helically agitated reactor. The yield from cellulose to ethanol in SSF again shows no obvious difference between the DDAP pretreated corn stover with and without impregnation. This study suggests that impregnation in DDAP was not necessary under the helical agitation mixing. The results provided a useful way of cost reduction and process simplification in pretreatment. PMID:24630497

  8. Dry dilute acid pretreatment by co-currently feeding of corn stover feedstock and dilute acid solution without impregnation.

    PubMed

    He, Yanqing; Zhang, Jian; Bao, Jie

    2014-04-01

    Impregnation of lignocellulose materials with dilute acid solution is a routine operation in conventional dilute acid pretreatment. The dry dilute acid pretreatment (DDAP) at high solids content up to 70% is naturally considered to require longer impregnation time. In this study, a co-currently feeding operation of corn stover and dilute sulfuric acid solution without any impregnation was tested for DDAP. The DDAP pretreated corn stover without impregnation is found to be essentially no difference in pretreatment efficiency compared to those with impregnation in the helically agitated reactor. The yield from cellulose to ethanol in SSF again shows no obvious difference between the DDAP pretreated corn stover with and without impregnation. This study suggests that impregnation in DDAP was not necessary under the helical agitation mixing. The results provided a useful way of cost reduction and process simplification in pretreatment.

  9. Recovery of rhenium from sulfuric acid solutions with activated coals

    SciTech Connect

    Troshkina, I.D.; Naing, K.Z.; Ushanova, O.N.; P'o, V.; Abdusalomov, A.A.

    2006-09-15

    Equilibrium and kinetic characteristics of rhenium sorption from sulfuric acid solutions (pH 2) by activated coals produced from coal raw materials (China) were studied. Constants of the Henry equation describing isotherms of rhenium sorption by activated coals were calculated. The effective diffusion coefficients of rhenium in the coals were determined. The dynamic characteristics of rhenium sorption and desorption were determined for the activated coal with the best capacity and kinetic characteristics.

  10. Corrosion Behavior of Alloy 22 in Oxalic Acid and Sodium Chloride Solutions

    SciTech Connect

    Day, S D; Whalen, M T; King, K J; Hust, G A; Wong, L L; Estill, J C; Rebak, R B

    2003-06-24

    Nickel based Alloy 22 (NO6022) is extensively used in aggressive industrial applications, especially due to its resistance to localized corrosion and stress corrosion cracking in high chloride environments. The purpose of this work was to characterize the anodic behavior of Alloy 22 in oxalic acid solution and to compare its behavior to sodium chloride (NaCl) solutions. Standard electrochemical tests such as polarization resistance and cyclic polarization were used. Results show that the corrosion rate of Alloy 22 in oxalic acid solutions increased rapidly as the temperature and the acid concentration increased. Extrapolation studies show that even at a concentration of 10{sup -4}M oxalic acid, the corrosion rate of Alloy 22 would be higher in oxalic acid than in 1 M NaCl solution. Alloy 22 was not susceptible to localized corrosion in oxalic acid solutions. Cyclic polarization tests in 1 M NaCl showed that Alloy 22 was susceptible to crevice corrosion at 90 C but was not susceptible at 60 C.

  11. Chemical evaluation of soil-solution in acid forest soils

    USGS Publications Warehouse

    Lawrence, G.B.; David, M.B.

    1996-01-01

    Soil-solution chemistry is commonly studied in forests through the use of soil lysimeters.This approach is impractical for regional survey studies, however, because lysimeter installation and operation is expensive and time consuming. To address these problems, a new technique was developed to compare soil-solution chemistry among red spruce stands in New York, Vermont, New Hampshire, Maine. Soil solutions were expelled by positive air pressure from soil that had been placed in a sealed cylinder. Before the air pressure was applied, a solution chemically similar to throughfall was added to the soil to bring it to approximate field capacity. After the solution sample was expelled, the soil was removed from the cylinder and chemically analyzed. The method was tested with homogenized Oa and Bs horizon soils collected from a red spruce stand in the Adirondack Mountains of New York, a red spruce stand in east-central Vermont, and a mixed hardwood stand in the Catskill Mountains of New York. Reproducibility, effects of varying the reaction time between adding throughfall and expelling soil solution (5-65 minutes) and effects of varying the chemical composition of added throughfall, were evaluated. In general, results showed that (i) the method was reproducible (coefficients of variation were generally < 15%), (ii) variations in the length of reaction-time did not affect expelled solution concentrations, and (iii) adding and expelling solution did not cause detectable changes in soil exchange chemistry. Concentrations of expelled solutions varied with the concentrations of added throughfall; the lower the CEC, the more sensitive expelled solution concentrations were to the chemical concentrations of added throughfall. Addition of a tracer (NaBr) showed that the expelled solution was a mixture of added solution and solution that preexisted in the soil. Comparisons of expelled solution concentrations with concentrations of soil solutions collected by zero-tension and

  12. Dissolved oxygen alteration of the spectrophotometric analysis and quantification of nucleic acid solutions.

    PubMed

    Doshi, Rupak; Day, Philip J R; Tirelli, Nicola

    2009-04-01

    Nucleic acids are routinely and readily analysed using the A(260)/A(280) ratio, although this method is known to be prone to erroneous results owing to contaminants in solution that absorb at similar wavelengths. The aim of the present review, while highlighting the problems and alternatives of using UV spectrophotometry for nucleic acid measurements, is to bring forth an observational result from our recent studies, namely that DO (dissolved oxygen) and nitrogen can alter the A(260) of aqueous DNA solutions. Our finding is of importance because DO is highly variable between protocols and storage conditions of DNA preparations. The physicochemical nature of the oxygen-DNA interactions is briefly discussed.

  13. Acid deposition in Maryland: Implications of the results of the National Acid Precipitation Assessment Program

    SciTech Connect

    DeMuro, J.; Bowmann, M.; Ross, J.; Blundell, C.; Price, R.

    1991-07-01

    Acid deposition, commonly referred to as 'acid rain,' is a major global environmental concern. Acid deposition has reportedly resulted in damage to aquatic, terrestrial, and physical resources and has potentially adverse effects on human health. A component of the Maryland acid deposition program is the preparation of an annual report that summarizes yearly activities and costs of ongoing acid deposition research and monitoring programs.

  14. A comparison of solute-transport solution techniques based on inverse modelling results

    USGS Publications Warehouse

    Mehl, S.; Hill, M.C.

    2000-01-01

    Five common numerical techniques (finite difference, predictor-corrector, total-variation-diminishing, method-of-characteristics, and modified-method-of-characteristics) were tested using simulations of a controlled conservative tracer-test experiment through a heterogeneous, two-dimensional sand tank. The experimental facility was constructed using randomly distributed homogeneous blocks of five sand types. This experimental model provides an outstanding opportunity to compare the solution techniques because of the heterogeneous hydraulic conductivity distribution of known structure, and the availability of detailed measurements with which to compare simulated concentrations. The present work uses this opportunity to investigate how three common types of results-simulated breakthrough curves, sensitivity analysis, and calibrated parameter values-change in this heterogeneous situation, given the different methods of simulating solute transport. The results show that simulated peak concentrations, even at very fine grid spacings, varied because of different amounts of numerical dispersion. Sensitivity analysis results were robust in that they were independent of the solution technique. They revealed extreme correlation between hydraulic conductivity and porosity, and that the breakthrough curve data did not provide enough information about the dispersivities to estimate individual values for the five sands. However, estimated hydraulic conductivity values are significantly influenced by both the large possible variations in model dispersion and the amount of numerical dispersion present in the solution technique.Five common numerical techniques (finite difference, predictor-corrector, total-variation-diminishing, method-of-characteristics, and modified-method-of-characteristics) were tested using simulations of a controlled conservative tracer-test experiment through a heterogeneous, two-dimensional sand tank. The experimental facility was constructed using randomly

  15. Photodegradation of Mercaptopropionic Acid- and Thioglycollic Acid-Capped CdTe Quantum Dots in Buffer Solutions.

    PubMed

    Miao, Yanping; Yang, Ping; Zhao, Jie; Du, Yingying; He, Haiyan; Liu, Yunshi

    2015-06-01

    CdTe quantum dots (QDs) were synthesized by 3-mercaptopropionic acid (MPA) and thioglycollic acid (TGA) as capping agents. It is confirmed that TGA and MPA molecules were attached on the surface of the QDs using Fourier transform infrared (FT-IR) spectra. The movement of the QDs in agarose gel electrophoresis indicated that MPA-capped CdTe QDs had small hydrodynamic diameter. The photoluminescence (PL) intensity of TGA-capped QDs is higher than that of MPA-capped QDs at same QD concentration because of the surface passivation of TGA. To systemically investigate the photodegradation, CdTe QDs with various PL peak wavelengths were dispersed in phosphate buffered saline (PBS) and Tris-borate-ethylenediaminetetraacetic acid (TBE) buffer solutions. It was found that the PL intensity of the QDs in PBS decreased with time. The PL peak wavelengths of the QDs in PBS solutions remained unchanged. As for TGA-capped CdTe QDs, the results of PL peak wavelengths in TBE buffer solutions indicated that S(2-) released by TGA attached to Cd(2+) and formed CdS-like clusters layer on the surface of aqueous CdTe QDs. In addition, the number of TGA on the CdTe QDs surface was more than that of MPA. When the QDs were added to buffer solutions, agents were removed from the surface of CdTe QDs, which decreased the passivation of agents thus resulted in photodegradation of CdTe QDs in buffer solutions.

  16. Poly(N-vinylimidazole) gels as insoluble buffers that neutralize acid solutions without dissolving.

    PubMed

    Horta, Arturo; Piérola, Inés F

    2009-04-01

    Typical buffers are solutions containing weak acids or bases. If these groups were anchored to insoluble gels, what would be their behavior? Simple thermodynamics is used to calculate the pH in two-phase systems that contain the weak acid or base fixed to only one of the phases and is absent in the other. The experimental reference of such systems are pH sensitive hydrogels and heterogeneous systems of biological interest. It is predicted that a basic hydrogel immersed in slightly acidic solutions should absorb the acid and leave the external solution exactly neutral (pH 7). This is in accordance with experimental results of cross-linked poly(N-vinylimidazole). The pH 7 cannot be obtained if the system were homogeneous; the confinement of the weak base inside the gel phase is a requisite for this neutral pH in the external solution. The solution inside the gel is regulated to a much higher pH, which has important implications in studies on chemical reactions and physical processes taking place inside a phase insoluble but in contact with a solution. PMID:19245223

  17. Isotherm-Based Thermodynamic Models for Solute Activities of Organic Acids with Consideration of Partial Dissociation.

    PubMed

    Nandy, Lucy; Ohm, Peter B; Dutcher, Cari S

    2016-06-23

    Organic acids make up a significant fraction of the organic mass in atmospheric aerosol particles. The calculation of gas-liquid-solid equilibrium partitioning of the organic acid is therefore critical for accurate determination of atmospheric aerosol physicochemical properties and processes such as new particle formation and activation to cloud condensation nuclei. Previously, an adsorption isotherm-based statistical thermodynamic model was developed for capturing solute concentration-activity relationships for multicomponent aqueous solutions over the entire concentration range (Dutcher et al. J. Phys. Chem. C/A 2011, 2012, 2013), with model parameters for energies of adsorption successfully related to dipole-dipole electrostatic forces in solute-solvent and solvent-solvent interactions for both electrolytes and organics (Ohm et al. J. Phys. Chem. A 2015). However, careful attention is needed for weakly dissociating semivolatile organic acids. Dicarboxylic acids, such as malonic acid and glutaric acid are treated here as a mixture of nondissociated organic solute (HA) and dissociated solute (H(+) + A(-)). It was found that the apparent dissociation was greater than that predicted by known dissociation constants alone, emphasizing the effect of dissociation on osmotic and activity coefficient predictions. To avoid additional parametrization from the mixture approach, an expression was used to relate the Debye-Hückel hard-core collision diameter to the adjustable solute-solvent intermolecular distance. An improved reference state treatment for electrolyte-organic aqueous mixtures, such as that observed here with partial dissociation, has also been proposed. This work results in predictive correlations for estimation of organic acid and water activities for which there is little or no activity data.

  18. Isotherm-Based Thermodynamic Models for Solute Activities of Organic Acids with Consideration of Partial Dissociation.

    PubMed

    Nandy, Lucy; Ohm, Peter B; Dutcher, Cari S

    2016-06-23

    Organic acids make up a significant fraction of the organic mass in atmospheric aerosol particles. The calculation of gas-liquid-solid equilibrium partitioning of the organic acid is therefore critical for accurate determination of atmospheric aerosol physicochemical properties and processes such as new particle formation and activation to cloud condensation nuclei. Previously, an adsorption isotherm-based statistical thermodynamic model was developed for capturing solute concentration-activity relationships for multicomponent aqueous solutions over the entire concentration range (Dutcher et al. J. Phys. Chem. C/A 2011, 2012, 2013), with model parameters for energies of adsorption successfully related to dipole-dipole electrostatic forces in solute-solvent and solvent-solvent interactions for both electrolytes and organics (Ohm et al. J. Phys. Chem. A 2015). However, careful attention is needed for weakly dissociating semivolatile organic acids. Dicarboxylic acids, such as malonic acid and glutaric acid are treated here as a mixture of nondissociated organic solute (HA) and dissociated solute (H(+) + A(-)). It was found that the apparent dissociation was greater than that predicted by known dissociation constants alone, emphasizing the effect of dissociation on osmotic and activity coefficient predictions. To avoid additional parametrization from the mixture approach, an expression was used to relate the Debye-Hückel hard-core collision diameter to the adjustable solute-solvent intermolecular distance. An improved reference state treatment for electrolyte-organic aqueous mixtures, such as that observed here with partial dissociation, has also been proposed. This work results in predictive correlations for estimation of organic acid and water activities for which there is little or no activity data. PMID:27222917

  19. GADOLINIUM OXALATE SOLUBILITY MEASUREMENTS IN NITRIC ACID SOLUTIONS

    SciTech Connect

    Pierce, R.

    2012-02-22

    HB-Line will begin processing Pu solutions during FY2012 that will involve the recovery of Pu using oxalate precipitation and filtration. After the precipitation and filtration processes, the filtrate solution will be transferred from HB-Line to H-Canyon. The presence of excess oxalate and unfiltered Pu oxalate solids in these solutions create a criticality safety issue if they are sent to H-Canyon without controls in H-Canyon. One approach involves H-Canyon receiving the filtrate solution into a tank that is poisoned with soluble gadolinium (Gd). Decomposition of the oxalate will occur within a subsequent H-Canyon vessel. The receipt of excess oxalate into the H-Canyon receipt tanks has the potential to precipitate a portion of the Gd poison in the receipt tanks. Because the amount of Gd in solution determines the maximum amount of Pu solids that H-Canyon can receive, H-Canyon Engineering requested that SRNL determine the solubility of Gd in aqueous solutions of 4-10 M nitric acid (HNO{sub 3}), 4-12 g/L Gd, and 0.15-0.25 M oxalic acid (H{sub 2}C{sub 2}O{sub 4}) at 25 C. The target soluble Gd concentration is 6 g/L. The data indicate that the target can be achieved above 6 M HNO{sub 3} and below 0.25 M H{sub 2}C{sub 2}O{sub 4}. For 6 M HNO{sub 3}, 10.5 g/L and 7 g/L Gd are soluble in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. In 4 M HNO{sub 3}, the Gd solubility drops significantly to 2 g/L and 0.25 g/L in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. The solubility of Gd at 8-10 M HNO{sub 3} exceeds the solubility at 6 M HNO{sub 3}. The data for 4 M HNO{sub 3} showed good agreement with data in the literature. To achieve a target of 6 g/L soluble Gd in solution in the presence of 0.15-0.25 M oxalate, the HNO{sub 3} concentration must be maintained at or above 6 M HNO{sub 3}.

  20. Isothermal heat measurements of TBP-nitric acid solutions

    SciTech Connect

    Smith, J.R.; Cavin, W.S.

    1994-12-16

    Net heats of reaction were measured in an isothermal calorimeter for both single phase (organic) and two phase (organic and aqueous) TBP/HNO{sub 3} reacting solutions at temperatures above 100 C. The oxidation rate constant was determined to be 5.4E-4 min{sup {minus}1} at 110 C for an open ``vented`` system as compared to 1.33 E-3 min{sup {minus}1} in the closed system. The heat released per unit material oxidized was also reduced. The oxidation in both phases was found to be first order in nitric acid and pseudo-zero order in butylnitrate and water. The hydrolysis (esterification) rate constant determined by Nichols` (1.33E-3 min{sup {minus}1}) fit the experimental data from this work well. Forced evaporation of the volatile components by the product gases from oxidation resulted in a cooling mechanism which more than balanced the heat from the oxidation reaction in the two-phased systems. Rate expressions were derived and rate constants determined for both the single and two phase systems. An approximating mathematical model was developed to fit the experimental data and to extrapolate beyond the experimental conditions. This model shows that one foot of ``reacting`` 14.3M HNO{sub 3} aqueous phase solution at 121 C will transport sufficient water to the organic phase to replace evaporative losses, maintaining endothermicity, for organic layers up to 12.2 + 6.0 feet deep. If the pressure in a reacting system is allowed to increase due to insufficient venting the temperature of the organic phase would increase in temperature to reach a new equilibrium. The rate of oxidation would increase not only due to the increase in temperature but also from the increased concentration of dissolved HNO{sub 3} reduction products. Another important factor is that the cooling system described in this work becomes less effective as the total pressure increases. These factors probably contributed to the explosion at Tomsk.

  1. Dissolution of Simulated and Radioactive Savannah River Site High-Level Waste Sludges with Oxalic Acid & Citric Acid Solutions

    SciTech Connect

    STALLINGS, MARY

    2004-07-08

    This report presents findings from tests investigating the dissolution of simulated and radioactive Savannah River Site sludges with 4 per cent oxalic acid and mixtures of oxalic and citric acid previously recommended by a Russian team from the Khlopin Radium Institute and the Mining and Chemical Combine (MCC). Testing also included characterization of the simulated and radioactive waste sludges. Testing results showed the following: Dissolution of simulated HM and PUREX sludges with oxalic and citric acid mixtures at SRTC confirmed general trends reported previously by Russian testing. Unlike the previous Russian testing six sequential contacts of a mixture of oxalic acid citric acids at a 2:1 ratio (v/w) of acid to sludge did not produce complete dissolution of simulated HM and PUREX sludges. We observed that increased sludge dissolution occurred at a higher acid to sludge ratio, 50:1 (v/w), compared to the recommended ratio of 2:1 (v/w). We observed much lower dissolution of aluminum in a simulated HM sludge by sodium hydroxide leaching. We attribute the low aluminum dissolution in caustic to the high fraction of boehmite present in the simulated sludge. Dissolution of HLW sludges with 4 per cent oxalic acid and oxalic/citric acid followed general trends observed with simulated sludges. The limited testing suggests that a mixture of oxalic and citric acids is more efficient for dissolving HM and PUREX sludges and provides a more homogeneous dissolution of HM sludge than oxalic acid alone. Dissolution of HLW sludges in oxalic and oxalic/citric acid mixtures produced residual sludge solids that measured at higher neutron poison to equivalent 235U weight ratios than that in the untreated sludge solids. This finding suggests that residual solids do not present an increased nuclear criticality safety risk. Generally the neutron poison to equivalent 235U weight ratios of the acid solutions containing dissolved sludge components are lower than those in the untreated

  2. Biosorption of acidic textile dyestuffs from aqueous solution by Paecilomyces sp. isolated from acidic mine drainage.

    PubMed

    Çabuk, Ahmet; Aytar, Pınar; Gedikli, Serap; Özel, Yasemin Kevser; Kocabıyık, Erçin

    2013-07-01

    Removal of textile dyestuffs from aqueous solution by biosorption onto a dead fungal biomass isolated from acidic mine drainage in the Çanakkale Region of Turkey was investigated. The fungus was found to be a promising biosorbent and identified as Paecilomyces sp. The optimal conditions for bioremediation were as follows: pH, 2.0; initial dyestuff concentration, 50 mg l(-1) for Reactive Yellow 85 and Reactive Orange 12, and 75 mg l(-1) for Reactive Black 8; biomass dosage, 2 g l(-1) for Reactive Yellow 85, 3 g l(-1) for Reactive Orange 12, 4 g l(-1) for Reactive Black 8; temperature, 25 °C; and agitation rate, 100 rpm. Zeta potential measurements indicated an electrostatic interaction between the binding sites and dye anions. Fourier transform infrared spectroscopy showed that amine, hydroxyl, carbonyl, and amide bonds were involved in the dyestuff biosorption. A toxicity investigation was also carried out before and after the biosorption process. These results showed that the toxicities for the reactive dyestuffs in aqueous solutions after biosorption studies decreased. The Freundlich and Langmuir adsorption models were used for the mathematical description of the biosorption equilibrium, and isotherm constants were evaluated for each dyestuff. Equilibrium data of biosorption of RY85 and RO12 dyestuffs fitted well to both models at the studied concentration and temperature.

  3. Discoloration of titanium alloy in acidic saline solutions with peroxide.

    PubMed

    Takemoto, Shinji; Hattori, Masayuki; Yoshinari, Masao; Kawada, Eiji; Oda, Yutaka

    2013-01-01

    The objective of this study was to compare corrosion behavior in several titanium alloys with immersion in acidulated saline solutions containing hydrogen peroxide. Seven types of titanium alloy were immersed in saline solutions with varying levels of pH and hydrogen peroxide content, and resulting differences in color and release of metallic elements determined in each alloy. Some alloys were characterized using Auger electron spectroscopy. Ti-55Ni alloy showed a high level of dissolution and difference in color. With immersion in solution containing hydrogen peroxide at pH 4, the other alloys showed a marked difference in color but a low level of dissolution. The formation of a thick oxide film was observed in commercially pure titanium showing discoloration. The results suggest that discoloration in titanium alloys immersed in hydrogen peroxide-containing acidulated solutions is caused by an increase in the thickness of this oxide film, whereas discoloration of Ti-55Ni is caused by corrosion. PMID:23370866

  4. Systems solutions by lactic acid bacteria: from paradigms to practice.

    PubMed

    de Vos, Willem M

    2011-08-30

    Lactic acid bacteria are among the powerhouses of the food industry, colonize the surfaces of plants and animals, and contribute to our health and well-being. The genomic characterization of LAB has rocketed and presently over 100 complete or nearly complete genomes are available, many of which serve as scientific paradigms. Moreover, functional and comparative metagenomic studies are taking off and provide a wealth of insight in the activity of lactic acid bacteria used in a variety of applications, ranging from starters in complex fermentations to their marketing as probiotics. In this new era of high throughput analysis, biology has become big science. Hence, there is a need to systematically store the generated information, apply this in an intelligent way, and provide modalities for constructing self-learning systems that can be used for future improvements. This review addresses these systems solutions with a state of the art overview of the present paradigms that relate to the use of lactic acid bacteria in industrial applications. Moreover, an outlook is presented of the future developments that include the transition into practice as well as the use of lactic acid bacteria in synthetic biology and other next generation applications. PMID:21995776

  5. Systems solutions by lactic acid bacteria: from paradigms to practice

    PubMed Central

    2011-01-01

    Lactic acid bacteria are among the powerhouses of the food industry, colonize the surfaces of plants and animals, and contribute to our health and well-being. The genomic characterization of LAB has rocketed and presently over 100 complete or nearly complete genomes are available, many of which serve as scientific paradigms. Moreover, functional and comparative metagenomic studies are taking off and provide a wealth of insight in the activity of lactic acid bacteria used in a variety of applications, ranging from starters in complex fermentations to their marketing as probiotics. In this new era of high throughput analysis, biology has become big science. Hence, there is a need to systematically store the generated information, apply this in an intelligent way, and provide modalities for constructing self-learning systems that can be used for future improvements. This review addresses these systems solutions with a state of the art overview of the present paradigms that relate to the use of lactic acid bacteria in industrial applications. Moreover, an outlook is presented of the future developments that include the transition into practice as well as the use of lactic acid bacteria in synthetic biology and other next generation applications. PMID:21995776

  6. Systems solutions by lactic acid bacteria: from paradigms to practice.

    PubMed

    de Vos, Willem M

    2011-08-30

    Lactic acid bacteria are among the powerhouses of the food industry, colonize the surfaces of plants and animals, and contribute to our health and well-being. The genomic characterization of LAB has rocketed and presently over 100 complete or nearly complete genomes are available, many of which serve as scientific paradigms. Moreover, functional and comparative metagenomic studies are taking off and provide a wealth of insight in the activity of lactic acid bacteria used in a variety of applications, ranging from starters in complex fermentations to their marketing as probiotics. In this new era of high throughput analysis, biology has become big science. Hence, there is a need to systematically store the generated information, apply this in an intelligent way, and provide modalities for constructing self-learning systems that can be used for future improvements. This review addresses these systems solutions with a state of the art overview of the present paradigms that relate to the use of lactic acid bacteria in industrial applications. Moreover, an outlook is presented of the future developments that include the transition into practice as well as the use of lactic acid bacteria in synthetic biology and other next generation applications.

  7. Formation of amino acids by cobalt-60 irradiation of hydrogen cyanide solutions

    NASA Technical Reports Server (NTRS)

    Sweeney, M. A.; Toste, A. P.; Ponnamperuma, C.

    1976-01-01

    Experiments were conducted to study the pathway for the prebiotic origin of amino acids from hydrogen cyanide (HCN) under the action of ionizing radiation considered as an effective source of energy on the primitive earth. The irradiations were performed in a cobalt-60 source with a dose rate of 200,000 rad/hr. Seven naturally occurring amino acids are identified among the products formed by the hydrolysis of gamma-irradiated solutions of HCN: glycine, alanine, valine, serine, threonine, aspartic acid, and glutamic acid. The identity of these amino acids is established by gas chromatography and mass spectrometry. Control experiments provided evidence that the amino acids are not the result of contamination.

  8. [Catalytic ozonation by ceramic honeycomb for the degradation of oxalic acid in aqueous solution].

    PubMed

    Zhao, Lei; Sun, Zhi-Zhong; Ma, Jun

    2007-11-01

    Comparative experiments for the degradation of oxalic acid in aqueous solution were carried out in the three processes of ozonation alone, ceramic honeycomb-catalyzed ozonation and ceramic honeycomb adsorption. The results show that the degradation rates of oxalic acid in the ceramic honeycomb-catalyzed ozonation, ozonation alone and ceramic honeycomb adsorption systems are 37.6%, 2.2% and 0.4%, and the presence of ceramic honeycomb catalyst significantly improves the degradation rate of oxalic acid compared to the results from non-catalytic ozonation and adsorption. With the addition of tert-butanol, the degradation rates of oxalic acid in catalytic ozonation system decrease by 24.1%, 29.0% and 30.1%, respectively, at the concentration of 5, 10 and 15 mg x L(-1). This phenomenon indicates that ceramic honeycomb-catalyzed ozonation for the degradation of oxalic acid in aqueous solution follows the mechanism of *OH oxidation, namely the heterogeneous surface of catalyst enhances the initiation of *OH. The results of TOC analysis demonstrate that the process of ceramic honeycomb-catalyzed ozonation can achieve the complete mineralization level without the formation of intermediary degradation products. The experimental results suggest that the reaction temperature has positive relationship with the degradation rate of oxalic acid. The degradation rates of oxalic acid in the ceramic honeycomb-catalyzed ozonation system are 16.4%, 37.6%, 61.3% and 68.2%, at the respective reaction temperature of 10, 20, 30 and 40 degrees C.

  9. PHYSICAL SOLUTIONS FOR ACID ROCK DRAINAGE AT REMOTE SITES DEMONSTRATION PROJECT

    EPA Science Inventory

    This report summarizes the results of Mine Waste Technology Program, Activity III, Project 42, Physical Solutions for Acid Rock Drainage at Remote Sites, funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by EPA and the U.S. Department of Energy. A...

  10. Electrocatalytic hydrogenation of 5-hydroxymethylfurfural in acidic solution.

    PubMed

    Kwon, Youngkook; Birdja, Yuvraj Y; Raoufmoghaddam, Saeed; Koper, Marc T M

    2015-05-22

    Electrocatalytic hydrogenation of 5-hydroxymethylfurfural (HMF) is studied on solid metal electrodes in acidic solution (0.5 M H2 SO4 ) by correlating voltammetry with on-line HPLC product analysis. Three soluble products from HMF hydrogenation are distinguished: 2,5-dihydroxymethylfuran (DHMF), 2,5-dihydroxymethyltetrahydrofuran (DHMTHF), and 2,5-dimethyl-2,3-dihydrofuran (DMDHF). Based on the dominant reaction products, the metal catalysts are divided into three groups: (1) metals mainly forming DHMF (Fe, Ni, Cu, and Pb), (2) metals forming DHMF and DMDHF depending on the applied potentials (Co, Ag, Au, Cd, Sb, and Bi), and (3) metals forming mainly DMDHF (Pd, Pt, Al, Zn, In, and Sb). Nickel and antimony are the most active catalysts for DHMF (0.95 mM cm(-2) at ca. -0.35 VRHE and -20 mA cm(-2) ) and DMDHF (0.7 mM cm(-2) at -0.6 VRHE and -5 mA cm(-2) ), respectively. The pH of the solution plays an important role in the hydrogenation of HMF: acidic condition lowers the activation energy for HMF hydro-genation and hydrogenates the furan ring further to tetrahydrofuran.

  11. Measurement of partial vapor pressure of ammonia over acid ammonium sulfate solutions by an integral method

    NASA Astrophysics Data System (ADS)

    Koutrakis, P.; Aurian-BlǎJeni, B.

    1993-02-01

    We present a simple, integral, passive method for measuring partial vapor pressure. Integral methods are useful tools when dealing with very low concentrations because collection over extended periods increases the analytical sensitivity. Passive methods have the advantage of not introducing constraints external to the system. The principle of the method used here is to selectively react the substance in the atmosphere over a solution with an immobilized coating on an appropriate support. The reaction product is not volatile, but is soluble and can be extracted in an appropriate solvent and analyzed. The method has been applied to measuring the vapor pressure of ammonia over aqueous solutions. The vapor pressure over ammonium sulfate solutions depends on the acidity of the solutions as well as on the salt concentration. The dependence can be explained with a simple model. Furthermore, using the same model, we calculated the ammonia vapor pressure above different ammonium sulfate/sulfuric acid aqueous solutions as a function of sulfate molarity and percentage of sulfuric acid. The results from the calculations suggest that for ambient ammonia concentrations less than 10 ppb, acid sulfate aerosols are not completely neutralized.

  12. Arsenic removal from acidic solutions with biogenic ferric precipitates.

    PubMed

    Ahoranta, Sarita H; Kokko, Marika E; Papirio, Stefano; Özkaya, Bestamin; Puhakka, Jaakko A

    2016-04-01

    Treatment of acidic solution containing 5g/L of Fe(II) and 10mg/L of As(III) was studied in a system consisting of a biological fluidized-bed reactor (FBR) for iron oxidation, and a gravity settler for iron precipitation and separation of the ferric precipitates. At pH 3.0 and FBR retention time of 5.7h, 96-98% of the added Fe(II) precipitated (99.1% of which was jarosite). The highest iron oxidation and precipitation rates were 1070 and 28mg/L/h, respectively, and were achieved at pH 3.0. Subsequently, the effect of pH on arsenic removal through sorption and/or co-precipitation was examined by gradually decreasing solution pH from 3.0 to 1.6 (feed pH). At pH 3.0, 2.4 and 1.6, the highest arsenic removal efficiencies obtained were 99.5%, 80.1% and 7.1%, respectively. As the system had ferric precipitates in excess, decreased arsenic removal was likely due to reduced co-precipitation at pH<2.4. As(III) was partially oxidized to As(V) in the system. In shake flask experiments, As(V) sorbed onto jarosite better than As(III). Moreover, the sorption capacity of biogenic jarosite was significantly higher than that of synthetic jarosite. The developed bioprocess simultaneously and efficiently removes iron and arsenic from acidic solutions, indicating potential for mining wastewater treatment. PMID:26705889

  13. Precipitation of plutonium from acidic solutions using magnesium oxide

    SciTech Connect

    Jones, S.A.

    1994-09-06

    Plutonium (IV) is only marginally soluble in alkaline solution. Precipitation of plutonium using sodium or potassium hydroxide to neutralize acidic solutions produces a gelatinous solid that is difficult to filter and an endpoint that is difficult to control. If the pH of the solution is too high, additional species precipitate producing an increased volume of solids separated. The use of magnesium oxide as a reagent has advantages. It is added as a solid (volume of liquid waste produced is minimized), the pH is self-limiting (pH does not exceed about 8.5), and the solids precipitated are more granular (larger particle size) than those produced using KOH or NaOH. Following precipitation, the raffinate is expected to meet criteria for disposal to tank farms. The solid will be heated in a furnace to dry it and convert any hydroxide salts to the oxide form. The material will be cooled in a desiccator. The material is expected to meet vault storage criteria.

  14. Near infrared photochemistry of pyruvic acid in aqueous solution.

    PubMed

    Larsen, Molly C; Vaida, Veronica

    2012-06-21

    Recent experimental and theoretical results have suggested that organic acids such as pyruvic acid, can be photolyzed in the ground electronic state by the excitation of the OH stretch vibrational overtone. These overtones absorb in the near-infrared and visible regions of the spectrum where the solar photons are plentiful and could provide a reaction pathway for the organic acids and alcohols that are abundant in the earth's atmosphere. In this paper the overtone initiated photochemistry of aqueous pyruvic acid is investigated by monitoring the evolution of carbon dioxide. In these experiments CO(2) is being produced by excitation in the near-infrared, between 850 nm and ∼1150 nm (11,765-8696 cm(-1)), where the second OH vibrational overtone (Δν = 3) of pyruvic acid is expected to absorb. These findings show not only that the overtone initiated photochemical decarboxylation reaction occurs but also that in the aqueous phase it occurs at a lower energy than was predicted for the overtone initiated reaction of pyruvic acid in the gas phase (13,380 cm(-1)). A quantum yield of (3.5 ± 1.0) × 10(-4) is estimated, suggesting that although this process does occur, it does so with a very low efficiency.

  15. Conformation of poly(γ-glutamic acid) in aqueous solution.

    PubMed

    Muroga, Yoshio; Nakaya, Asami; Inoue, Atsuki; Itoh, Daiki; Abiru, Masaya; Wada, Kaori; Takada, Masako; Ikake, Hiroki; Shimizu, Shigeru

    2016-04-01

    Local conformation and overall conformation of poly(γ-DL-glutamic acid) (PγDLGA) and poly(γ-L-glutamic acid) (PγLGA) in aqueous solution was studied as a function of degree of ionization ε by (1) H-NMR, circular dichroism, and potentiometric titration. It was clarified that their local conformation is represented by random coil over an entire ε range and their overall conformation is represented by expanded random-coil in a range of ε > ε(*) , where ε(*) is about 0.3, 0.35, 0.45, and 0.5 for added-salt concentration of 0.02M, 0.05M, 0.1M, and 0.2M, respectively. In a range of ε < ε(*) , however, ε dependence of their overall conformation is significantly differentiated from each other. PγDLGA tends to aggregate intramolecularly and/or intermolecularly with decreasing ε, but PγLGA still behaves as expanded random-coil. It is speculated that spatial arrangement of adjacent carboxyl groups along the backbone chain essentially affects the overall conformation of PγGA in acidic media.

  16. Infrared optical constants of H2O ice, amorphous nitric acid solutions, and nitric acid hydrates

    NASA Technical Reports Server (NTRS)

    Toon, Owen B.; Koehler, Birgit G.; Middlebrook, Ann M.; Tolbert, Margaret A.; Jordon, Joseph

    1994-01-01

    We determined the infrared optical constants of nitric acid trihydrate, nitric acid dihydrate, nitric acid monohydrate, and solid amorphous nitric acid solutions which crystallize to form these hydrates. We have also found the infrared optical constants of H2O ice. We measured the transmission of infrared light throught thin films of varying thickness over the frequency range from about 7000 to 500/cm at temperatures below 200 K. We developed a theory for the transmission of light through a substrate that has thin films on both sides. We used an iterative Kramers-Kronig technique to determine the optical constants which gave the best match between measured transmission spectra and those calculated for a variety of films of different thickness. These optical constants should be useful for calculations of the infrared spectrum of polar stratospheric clouds.

  17. Experimental Shock Chemistry of Aqueous Amino Acid Solutions and the Cometary Delivery of Prebiotic Compounds

    NASA Astrophysics Data System (ADS)

    Blank, Jennifer G.; Miller, Gregory H.; Ahrens, Michael J.; Winans, Randall E.

    2001-02-01

    A series of shock experiments were conducted to assess the feasibility of the delivery of organic compounds to the Earth via cometary impacts. Aqueous solutions containing near-saturation levels of amino acids (lysine, norvaline, aminobutyric acid, proline, and phenylalanine) were sealed inside stainless steel capsules and shocked by ballistic impact with a steel projectile plate accelerated along a 12-m-long gun barrel to velocities of 0.5-1.9 km sec^-1. Pressure-temperature-time histories of the shocked fluids were calculated using 1D hydrodynamical simulations. Maximum conditions experienced by the solutions lasted 0.85-2.7 μs and ranged from 5.1-21 GPa and 412-870 K. Recovered sample capsules were milled open and liquid was extracted. Samples were analyzed using high performance liquid chromatography (HPLC) and mass spectrometry (MS). In all experiments, a large fraction of the amino acids survived. We observed differences in kinetic behavior and the degree of survivability among the amino acids. Aminobutyric acid appeared to be the least reactive, and phenylalanine appeared to be the most reactive of the amino acids. The impact process resulted in the formation of peptide bonds; new compounds included amino acid dimers and cyclic diketopiperazines. In our experiments, and in certain naturally occurring impacts, pressure has a greater influence than temperature in determining reaction pathways. Our results support the hypothesis that significant concentrations of organic material could survive a natural impact process.

  18. Experimental shock chemistry of aqueous amino acid solutions and the cometary delivery of prebiotic compounds.

    PubMed

    Blank, J G; Miller, G H; Ahrens, M J; Winans, R E

    2001-01-01

    A series of shock experiments were conducted to assess the feasibility of the delivery of organic compounds to the Earth via cometary impacts. Aqueous solutions containing near-saturation levels of amino acids (lysine, norvaline, aminobutyric acid, proline, and phenylalanine) were sealed inside stainless steel capsules and shocked by ballistic impact with a steel projectile plate accelerated along a 12-m-long gun barrel to velocities of 0.5-1.9 km sec-1. Pressure-temperature-time histories of the shocked fluids were calculated using 1D hydrodynamical simulations. Maximum conditions experienced by the solutions lasted 0.85-2.7 microseconds and ranged from 5.1-21 GPa and 412-870 K. Recovered sample capsules were milled open and liquid was extracted. Samples were analyzed using high performance liquid chromatography (HPLC) and mass spectrometry (MS). In all experiments, a large fraction of the amino acids survived. We observed differences in kinetic behavior and the degree of survivability among the amino acids. Aminobutyric acid appeared to be the least reactive, and phenylalanine appeared to be the most reactive of the amino acids. The impact process resulted in the formation of peptide bonds; new compounds included amino acid dimers and cyclic diketopiperazines. In our experiments, and in certain naturally occurring impacts, pressure has a greater influence than temperature in determining reaction pathways. Our results support the hypothesis that significant concentrations of organic material could survive a natural impact process. PMID:11296518

  19. Effect of acid solutions on plants studied by the optical beam deflection method.

    PubMed

    Nie, Liangjiao; Kuboda, Mitsutoshi; Inoue, Tomomi; Wu, Xingzheng

    2013-12-01

    The optical beam deflection method was applied to study the effects of acid solution on both a terrestial and aquatic plants Egeria and Cerastium, which are common aquatic plant and terrestial weed respectively. A probe beam from a He-Ne laser was passed through a vicinity of a leaf of the plants, which were put in culture dishes filled with acid solutions. Deflection signals of the probe beam were monitored and compared for acid solutions with different pH values. The results of Egria showed that the deflection signals changed dramatically when pH values of acid solutions were 2.0 and 3.0, while little at pH of 4.0 and 5.0. For Cerastium when pH were below 3.0, deflection signals changed greatly with time at the begining. After a certain period of time, deflection signals changed little with time. When pH value was above 4.0, deflection signals of Cerastium were still changing with time even after 20 hours. The results suggested that the damage threshold of pH was between 3.0 and 4.0 for both the land and aquatic plants.

  20. Cesium absorption from acidic solutions using ammonium molybdophosphate on a polyacrylonitrile support (AMP-PAN)

    SciTech Connect

    Miller, C.J.; Olson, A.L.; Johnson, C.K.

    1995-12-01

    Recent efforts at the Idaho Chemical Processing Plant (ICPP) have included evaluation of cesium removal technologies as applied to ICPP acidic radioactive waste streams. Ammonium molybdophosphate (AMP) immobilized on a polyacrylonitrile support (AMP-PAN) has been studied as an ion exchange agent for cesium removal from acidic waste solutions. Capacities, distribution coefficients, elutability, and kinetics of cesium-extraction have been evaluated. Exchange breakthrough curves using small columns have been determined from 1M HNO{sub 3} and simulated waste solutions. The theoretical capacity of AMP is 213 g Cs/kg AMP. The average experimental capacity in batch contacts with various acidic solutions was 150 g Cs/kg AMP. The measured cesium distribution coefficients from actual waste solutions were 3287 mL/g for dissolved zirconia calcines, and 2679 mL/g for sodium-bearing waste. The cesium in the dissolved alumina calcines was analyzed for; however, the concentration was below analytical detectable limits resulting in inconclusive results. The reaction kinetics are very rapid (2-10 minutes). Cesium absorption appears to be independent of acid concentration over the range tested (0.1 M to 5 M HNO{sub 3}).

  1. Effect of acid solutions on plants studied by the optical beam deflection method.

    PubMed

    Nie, Liangjiao; Kuboda, Mitsutoshi; Inoue, Tomomi; Wu, Xingzheng

    2013-12-01

    The optical beam deflection method was applied to study the effects of acid solution on both a terrestial and aquatic plants Egeria and Cerastium, which are common aquatic plant and terrestial weed respectively. A probe beam from a He-Ne laser was passed through a vicinity of a leaf of the plants, which were put in culture dishes filled with acid solutions. Deflection signals of the probe beam were monitored and compared for acid solutions with different pH values. The results of Egria showed that the deflection signals changed dramatically when pH values of acid solutions were 2.0 and 3.0, while little at pH of 4.0 and 5.0. For Cerastium when pH were below 3.0, deflection signals changed greatly with time at the begining. After a certain period of time, deflection signals changed little with time. When pH value was above 4.0, deflection signals of Cerastium were still changing with time even after 20 hours. The results suggested that the damage threshold of pH was between 3.0 and 4.0 for both the land and aquatic plants. PMID:25078849

  2. Citric Acid-Modified Fenton's Reaction for the Oxidation of Chlorinated Ethylenes in Soil Solution Systems

    SciTech Connect

    Seol, Yongkoo; Javandel, Iraj

    2008-03-15

    Fenton's reagent, a solution of hydrogen peroxide and ferrous iron catalyst, is used for an in-situ chemical oxidation of organic contaminants. Sulfuric acid is commonly used to create an acidic condition needed for catalytic oxidation. Fenton's reaction often involves pressure buildup and precipitation of reaction products, which can cause safety hazards and diminish efficiency. We selected citric acid, a food-grade substance, as an acidifying agent to evaluate its efficiencies for organic contaminant removal in Fenton's reaction, and examined the impacts of using citric acid on the unwanted reaction products. A series of batch and column experiments were performed with varying H{sub 2}O{sub 2} concentrations to decompose selected chlorinated ethylenes. Either dissolved iron from soil or iron sulfate salt was added to provide the iron catalyst in the batch tests. Batch experiments revealed that both citric and sulfuric acid systems achieved over 90% contaminant removal rates, and the presence of iron catalyst was essential for effective decontamination. Batch tests with citric acid showed no signs of pressure accumulation and solid precipitations, however the results suggested that an excessive usage of H{sub 2}O{sub 2} relative to iron catalysts (Fe{sup 2+}/H{sub 2}O{sub 2} < 1/330) would result in lowering the efficiency of contaminant removal by iron chelations in the citric acid system. Column tests confirmed that citric acid could provide suitable acidic conditions to achieve higher than 55% contaminant removal rates.

  3. The extraction of actinides from nitric acid solutions with diamides of dipicolinic acid

    NASA Astrophysics Data System (ADS)

    Lapka, Joseph L.; Paulenova, Alena; Alyapyshev, Mikhail Yu; Babain, Vasiliy A.; Law, Jack D.; Herbst, R. Scott

    2010-03-01

    Diamides of dipicolinic acid (N,N'-diethyl-N,N'-ditolyl-dipicolinamide, EtTDPA) were synthesized and evaluated for their extraction capability for actinides. In this work the extractions of neptunium(V), protactinium(V), and thorium(IV) with EtTDPA in a polar fluorinated diluent from nitric acid were investigated. EtTDPA shows a high affinity for Th(IV) even at millimolar concentrations. Np(V) and Pa(V) are both reasonably extractable with EtTDPA; however, near saturated solutions are required to achieve appreciable distribution ratios. A comparison with previously published actinide extraction data is given.

  4. Laboratory evaluation of limestone and lime neutralization of acidic uranium mill tailings solution. Progress report

    SciTech Connect

    Opitz, B.E.; Dodson, M.E.; Serne, R.J.

    1984-02-01

    Experiments were conducted to evaluate a two-step neutralization scheme for treatment of acidic uranium mill tailings solutions. Tailings solutions from the Lucky Mc Mill and Exxon Highland Mill, both in Wyoming, were neutralized with limestone, CaCO/sub 3/, to an intermediate pH of 4.0 or 5.0, followed by lime, Ca(OH)/sub 2/, neutralization to pH 7.3. The combination limestone/lime treatment methods, CaCO/sub 3/ neutralization to pH 4 followed by neutralization with Ca(OH)/sub 2/ to pH 7.3 resulted in the highest quality effluent solution with respect to EPA's water quality guidelines. The combination method is the most cost-effective treatment procedure tested in our studies. Neutralization experiments to evaluate the optimum solution pH for contaminant removal were performed on the same two tailings solutions using only lime Ca(OH)/sub 2/ as the neutralizing agent. The data indicate solution neutralization above pH 7.3 does not significantly increase removal of pH dependent contaminants from solution. Column leaching experiments were performed on the neutralized sludge material (the precipitated solid material which forms as the acidic tailings solutions are neutralized to pH 4 or above). The sludges were contacted with laboratory prepared synthetic ground water until several effluent pore volumes were collected. Effluent solutions were analyzed for macro ions, trace metals and radionuclides in an effort to evaluate the long term effectiveness of attenuating contaminants in sludges formed during solution neutralization. Neutralized sludge leaching experiments indicate that Ca, Na, Mg, Se, Cl, and SO/sub 4/ are the only constituents which show solution concentrations significantly higher than the synthetic ground water in the early pore volumes of long-term leaching studies.

  5. The Kinetics and Mechanism of the Decomposition of Murexide in Acid Solution: An Experiment for Teaching Principles of Chemical Kinetics.

    ERIC Educational Resources Information Center

    Knoche, Wilhelm; Rees, Norman H.

    1984-01-01

    Background information, procedures, and typical results are provided for an experiment on the decomposition of murexide in acid solution. The experiment, suitable for advanced courses, can be easily performed in a 6-hour laboratory period. (JN)

  6. Radiolysis gases from nitric acid solutions containing HSA and HAN

    SciTech Connect

    Smith, J.R.

    1994-10-28

    The concentration of hydrogen (H{sub 2}) in the radiolytically produced off-gas from 2.76-4.25M HNO{sub 3}/PU solutions has been found to be greatly reduced in the presence of sulfamic acid (HSA) and hydroxylamine nitrate (HAN). The H{sub 2} concentration ([H{sub 2}]) is reduced from 35 percent to about 4 percent by dilution caused from an increase in the production rates of nitrogen (N{sub 2}), nitrous oxide (N{sub 2}O), and oxygen (O{sub 2}) gases. The generation rate of H{sub 2} was not affected by HSA or HAN giving a measured radiolytic yield, G(H{sub 2}), value of 0.201 molecules/100 eV for 2.765M NO{sub 3}{sup -} solution (a value of 0.213 is predicted from previous data). The G(H{sub 2}) values are dependent on the solution nitrate concentration ([NO{sub 3}{sup -}]). The generation rates of N{sub 2}, N{sub 2}O, and O{sub 2} are not dependent on the [NO{sub 3}{sup -}] in this narrow range, but are dependent on the presence of HSA and the concentration of HAN. The percentage [H{sub 2}] for the 2.5 to 3.0M NO{sub 3}{sup -} range expected in the off- from the FB-Line Pu{sup +3} Hold Tanks is conservatively estimated to be about 3.5 to 4.5 % for Pu + 3 solutions initially containing 0.023M HAN/0.165M HSA. The upper limit [H{sub 2}] may actually be about 4.1 % (4.3 % at 90 % confidence limits) but more {open_quotes}initial{close_quotes} off-gas rate data is needed at about 2.9M [NO{sub 3}{sup -}] in Pu{sup +3} solution for verification. Addition of ascorbic acid had no effect on the off-gas rate of Pu{sup +3} solutions containing HSA and NO{sub 3}{sup -} concentrations higher than those expected in the hold tanks. The maximum {open_quotes}hold time{close_quotes} for 50 grams/liter Pu{sup +3}/0.165M HSA/0.023M HAN/2.5-3.0M HNO{sub 3} solution is 20.3{+-}2.1 days. After this time the HSA initially present will become exhausted and the [H{sub 2}] will increase to 35 %. This hold time may be longer in [NO{sub 3}{sup -}] < 3.0M, but again more study is needed.

  7. GADOLINIUM OXALATE SOLUBILITY MEASUREMENTS IN NITRIC ACID SOLUTIONS

    SciTech Connect

    Pierce, R. A.

    2012-03-12

    HB-Line will begin processing Pu solutions during FY2012 that will involve the recovery of Pu using oxalate precipitation and filtration. After the precipitation and filtration processes, the filtrate solution will be transferred from HB-Line to H-Canyon. The presence of excess oxalate and unfiltered Pu oxalate solids in these solutions create a criticality safety issue if they are sent to H-Canyon without controls in H-Canyon. One approach involves H-Canyon receiving the filtrate solution into a tank that is poisoned with soluble gadolinium (Gd). Decomposition of the oxalate will occur within a subsequent H-Canyon vessel. The receipt of excess oxalate into the H-Canyon receipt tanks has the potential to precipitate a portion of the Gd poison in the receipt tanks. Because the amount of Gd in solution determines the maximum amount of Pu solids that H-Canyon can receive, H-Canyon Engineering requested that SRNL determine the solubility of Gd in aqueous solutions of 4-10 M nitric acid (HNO{sub 3}), 4-12 g/L Gd, and 0.15-0.25 M oxalic acid (H{sub 2}C{sub 2}O{sub 4}) at 25 °C. The target soluble Gd concentration is 6 g/L. The data indicate that the target can be achieved above 6 M HNO{sub 3} and below 0.25 M H{sub 2}C{sub 2}O{sub 4}. At 25 °C, for 6 M HNO{sub 3}, 11 g/L and 7 g/L Gd are soluble in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. In 4 M HNO{sub 3}, the Gd solubility drops significantly to 2.5 g/L and 0.8 g/L in 0.15 M and 0.25 M H{sub 2}C{sub 2}O{sub 4}, respectively. The solubility of Gd at 8-10 M HNO{sub 3} exceeds the solubility at 6 M HNO{sub 3}. The data for 4 M HNO{sub 3} showed good agreement with data in the literature. To achieve a target of 6 g/L soluble Gd in solution in the presence of 0.15-0.25 M oxalate, the HNO{sub 3} concentration must be maintained at or above 6 M HNO{sub 3}. The solubility of Gd in 4 M HNO{sub 3} with 0.15 M oxalate at 10 °C is about 1.5 g/L. For 6 M HNO{sub 3} with 0.15 M oxalate, the solubility of Gd at 10

  8. Novel Regenerated Solvent Extraction Processes for the Recovery of Carboxylic Acids or Ammonia from Aqueous Solutions Part I. Regeneration of Amine-Carboxylic Acid Extracts

    SciTech Connect

    Poole, L.J.; King, C.J.

    1990-03-01

    Two novel regenerated solvent extraction processes are examined. The first process has the potential to reduce the energy costs inherent in the recovery of low-volatility carboxylic acids from dilute aqueous solutions. The second process has the potential for reducing the energy costs required for separate recovery of ammonia and acid gases (e.g. CO{sub 2} and H{sub 2}S) from industrial sour waters. The recovery of carboxylic acids from dilute aqueous solution can be achieved by extraction with tertiary amines. An approach for regeneration and product recovery from such extracts is to back-extract the carboxylic acid with a water-soluble, volatile tertiary amine, such as trimethylamine. The resulting trimethylammonium carboxylate solution can be concentrated and thermally decomposed, yielding the product acid and the volatile amine for recycle. Experimental work was performed with lactic acid, succinic acid, and fumaric acid. Equilibrium data show near-stoichiometric recovery of the carboxylic acids from an organic solution of Alamine 336 into aqueous solutions of trimethylamine. For fumaric and succinic acids, partial evaporation of the aqueous back extract decomposes the carboxylate and yields the acid product in crystalline form. The decomposition of aqueous solutions of trimethylammonium lactates was not carried out to completion, due to the high water solubility of lactic acid and the tendency of the acid to self-associate. The separate recovery of ammonia and acid gases from sour waters can be achieved by combining steam-stripping of the acid gases with simultaneous removal of ammonia by extraction with a liquid cation exchanger. The use of di-2,4,4-trimethylpentyl phosphinic acid as the liquid cation exchanger is explored in this work. Batch extraction experiments were carried out to measure the equilibrium distribution ratio of ammonia between an aqueous buffer solution and an organic solution of the phosphinic acid (0.2N) in Norpar 12. The concentration

  9. Optical properties of chitosan in aqueous solution of L- and D-ascorbic acids

    NASA Astrophysics Data System (ADS)

    Malinkina, Olga N.; Shipovskaya, Anna B.; Kazmicheva, Olga F.

    2016-04-01

    The optical properties of aqueous chitosan solutions in L- and D-ascorbic acids were studied by optical rotatory dispersion and spectrophotometry. The specific optical rotation [α] of all chitosan solutions tested was positive, in contrast to aqueous solutions of the ascorbic acid enantiomers, which exhibit an inverse relationship of [α] values. Significant differences in the absolute values of [α] of the chitosan solutions at polymer-acid ratios exceeding the equimolar one were found.

  10. A unified molecular picture of the surfaces of aqueous acid, base, and salt solutions

    SciTech Connect

    Mucha, M.; Frigato, Tomaso; Levering, Lori; Allen, Heather C.; Tobias, Douglas J.; Dang, Liem X.; Jungwirth, Pavel

    2005-04-28

    A unified view of the structure of the air/solution interface of simple aqueous electrolytes containing monovalent inorganic ions is developed using molecular dynamics simulations and vibrational sum frequency generation spectroscopy. In salt solutions and bases the positively charged ions, such as alkali cations, are repelled from the air/solution interface, while the anions, such as halides or hydroxide, exhibit a varying propensity for the surface, correlated primarily with the polarizability of the ion. As a result, there is a net depletion of ions from the interfacial layer as a whole, which is connected via the Gibbs adsorption equation to an increase in surface tension with respect to neat water. The behavior of acids, such as aqueous HCl or HBr, is different due to a significant propensity of hydronium cations for the air/solution interface. Therefore, both cations and anions exhibit enhanced concentrations at the surface and, consequently, these acids reduce the surface tension of water. The key to the qualitatively different surface behavior of aqueous salt solutions and bases on one side and acids on the other thus lies in the appreciable adsorption of hydronium cations at the air/solution interface with their “hydrophobic” oxygen side oriented towards the gas phase. The results of the molecular dynamics calculations are supported by surface selective non-linear vibrational spectroscopy, which reveals among other things that the hydronium cations are present at the air/solution interface. The propensity of inorganic ions for the air/solution interface has important implications for heterogeneous chemical processes, in particular for atmospheric chemistry.

  11. Effect of Organic Acid Additions on the General and Localized Corrosion Susceptibility of Alloy 22 in Chloride Solutions

    SciTech Connect

    Carranza, R M; Giordano, C M; Rodr?guez, M A; Ilevbare, G O; Rebak, R B

    2007-08-28

    Electrochemical studies such as cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 (N06022) in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. All the tested material was wrought Mill Annealed (MA). Tests were also performed in NaCl solutions containing weak organic acids such as oxalic, acetic, citric and picric. Results show that the corrosion rate of Alloy 22 was significantly higher in solutions containing oxalic acid than in solutions of pure NaCl at the same pH. Citric and picric acids showed a slightly higher corrosion rate, and acetic acid maintained the corrosion rate of pure chloride solutions at the same pH. Organic acids revealed to be weak inhibitors for crevice corrosion. Higher concentration ratios, compared to nitrate ions, were needed to completely inhibit crevice corrosion in chloride solutions. Results are discussed considering acid dissociation constants, buffer capacity and complex formation constants of the different weak acids.

  12. Passive and transpassive anodic behavior of chalcopyrite in acid solutions

    NASA Astrophysics Data System (ADS)

    Warren, G. W.; Wadsworth, M. E.; El-Raghy, S. M.

    1992-01-01

    The electrochemical oxidation of CuFeS2 in various acid solutions was studied using electrodes made from massive samples. The primary techniques employed were potentiodynamic polarization and constant potential experiments supplemented by capacitance measurements. It was the purpose of this study to investigate the behavior of: (1) several sources of CuFeS2 in H2SO4 electrolytes, and (2) a single source of CuFeS2 in various dilute acids. Electrochemical characterization of CuFeS2 from various locations was performed in 1 M H2SO4 which showed significant differences in their behavior. All samples exhibited passive-like response during anodic polarization. The current density in this passive region was reproducible and showed differences of up to two orders of magnitude between samples from different sources which has been attributed mainly to the presence of impurities in some of the samples. During anodic polarization CuFeS2 was found to be sensitive to pH at higher potential, but insensitive at low potential in sulfate solution. In addition, current decay measurements at constant potential in the low potential-passive region were found to follow the Sato-Cohen (logarithmic) model for solid film formation. Based on current and mass balance measurements, two intermediate sulfide phases appeared to form in the sequence CuFeS2 → S, → S2. At higher potentials, in the transpassive region, the observed increase in current is compatible with the decomposition of water to form chemisorbed oxygen which releases copper and forms sulfate ions.

  13. Passive and transpassive anodic behavior of chalcopyrite in acid solutions

    NASA Astrophysics Data System (ADS)

    Warren, G. W.; Wadsworth, M. E.; El-Raghy, S. M.

    1982-12-01

    The electrochemical oxidation of CuFeS2 in various acid solutions was studied using electrodes made from massive samples. The primary techniques employed were potentiodynamic polarization and constant potential experiments supplemented by capacitance measurements. It was the purpose of this study to investigate the behavior of: (1) several sources of CuFeS2 in H2SO4 electrolytes, and (2) a single source of CuFeS2 in various dilute acids. Electrochemical characterization of CuFeS2 from various locations was performed in 1 M H2SO4 which showed significant differences in their behavior. All samples exhibited passive-like response during anodic polarization. The current density in this passive region was reproducible and showed differences of up to two orders of magnitude between samples from different sources which has been attributed mainly to the presence of impurities in some of the samples. During anodic polarization CuFeS2 was found to be sensitive to pH at higher potential, but insensitive at low potential in sulfate solution. In addition, current decay measurements at constant potential in the low potential-passive region were found to follow the Sato-Cohen (logarithmic) model for solid film formation. Based on current and mass balance measurements, two intermediate sulfide phases appeared to form in the sequence CuFeS2→S1→S2. At higher potentials, in the transpassive region, the observed increase in current is compatible with the decomposition of water to form chemisorbed oxygen which releases copper and forms sulfate ions.

  14. Interaction of Atmospheric-Pressure Air Microplasmas with Amino Acids as Fundamental Processes in Aqueous Solution.

    PubMed

    Zhou, Renwu; Zhou, Rusen; Zhuang, Jinxing; Zong, Zichao; Zhang, Xianhui; Liu, Dongping; Bazaka, Kateryna; Ostrikov, Kostya

    2016-01-01

    Plasma medicine is a relatively new field that investigates potential applications of cold atmospheric-pressure plasmas in bioengineering, such as for bacterial inactivation and degradation of organic molecules in water. In order to enunciate mechanisms of bacterial inactivation at molecular or atomic levels, we investigated the interaction of atmospheric-pressure air microplasmas with amino acids in aqueous solution by using high-resolution mass spectrometry (HRMS). Results show that the oxidation effect of plasma-induced species on the side chains of the amino acids can be categorized into four types, namely hydroxylation, nitration, dehydrogenation and dimerization. In addition, relative activities of amino acids resulting from plasma treatment come in descending order as follows: sulfur-containing carbon-chain amino acids > aromatic amino acids > five-membered ring amino acids > basic carbon-chain amino acids. Since amino acids are building blocks of proteins vital to the growth and reproduction of bacteria, these results provide an insight into the mechanism of bacterial inactivation by plasma. PMID:27183129

  15. Interaction of Atmospheric-Pressure Air Microplasmas with Amino Acids as Fundamental Processes in Aqueous Solution

    PubMed Central

    Zhou, Renwu; Zhou, Rusen; Zhuang, Jinxing; Zong, Zichao; Zhang, Xianhui; Liu, Dongping; Bazaka, Kateryna; Ostrikov, Kostya

    2016-01-01

    Plasma medicine is a relatively new field that investigates potential applications of cold atmospheric-pressure plasmas in bioengineering, such as for bacterial inactivation and degradation of organic molecules in water. In order to enunciate mechanisms of bacterial inactivation at molecular or atomic levels, we investigated the interaction of atmospheric-pressure air microplasmas with amino acids in aqueous solution by using high-resolution mass spectrometry (HRMS). Results show that the oxidation effect of plasma-induced species on the side chains of the amino acids can be categorized into four types, namely hydroxylation, nitration, dehydrogenation and dimerization. In addition, relative activities of amino acids resulting from plasma treatment come in descending order as follows: sulfur-containing carbon-chain amino acids > aromatic amino acids > five-membered ring amino acids > basic carbon-chain amino acids. Since amino acids are building blocks of proteins vital to the growth and reproduction of bacteria, these results provide an insight into the mechanism of bacterial inactivation by plasma. PMID:27183129

  16. Interaction of Atmospheric-Pressure Air Microplasmas with Amino Acids as Fundamental Processes in Aqueous Solution.

    PubMed

    Zhou, Renwu; Zhou, Rusen; Zhuang, Jinxing; Zong, Zichao; Zhang, Xianhui; Liu, Dongping; Bazaka, Kateryna; Ostrikov, Kostya

    2016-01-01

    Plasma medicine is a relatively new field that investigates potential applications of cold atmospheric-pressure plasmas in bioengineering, such as for bacterial inactivation and degradation of organic molecules in water. In order to enunciate mechanisms of bacterial inactivation at molecular or atomic levels, we investigated the interaction of atmospheric-pressure air microplasmas with amino acids in aqueous solution by using high-resolution mass spectrometry (HRMS). Results show that the oxidation effect of plasma-induced species on the side chains of the amino acids can be categorized into four types, namely hydroxylation, nitration, dehydrogenation and dimerization. In addition, relative activities of amino acids resulting from plasma treatment come in descending order as follows: sulfur-containing carbon-chain amino acids > aromatic amino acids > five-membered ring amino acids > basic carbon-chain amino acids. Since amino acids are building blocks of proteins vital to the growth and reproduction of bacteria, these results provide an insight into the mechanism of bacterial inactivation by plasma.

  17. Mixed field radiation effects on dry and acidic solution saturated polyamide 6,6

    NASA Astrophysics Data System (ADS)

    Brown, L.; Bonin, H. W.; Bui, V. T.

    2005-05-01

    The disposal of Canada's radioactive waste materials has been the focus of ongoing research at the Royal Military College of Canada, in the use of polymer-based composite materials for the fabrication of disposal containers. An evaluation of the performance of polyamide 6,6 after exposure to radiation and acidic aqueous solutions provides the basis for the assessment of the lifetime performance of a polymeric-based storage container. This work demonstrates the importance of the combined effects of aqueous solution diffusion and radiation exposure on the mechanical performance and molecular structure of polyamide 6,6. Irradiation of dry samples initially results in a marked reduction of mechanical performance, however, post-irradiation aging allows for the return to pre-irradiation mechanical strength. Samples irradiated after exposure to either distilled water or 0.1 M sulfuric acid solutions exhibited increases in mechanical performance upon exposure to a mixed field radioactive environment.

  18. Influence of biuret and cyanuric acid on dewaxing petroleum stocks with alcoholic urea solution

    SciTech Connect

    Abdullaev, E.Sh.; Ismailov, A.G.; Gadzhiev, A.Sh.; Balayan, R.D.

    1987-11-01

    The influence of biuret and cyanuric acid contents on the formation and separation of the adduct in commercial dewaxing of petroleum stocks by a urea solution in a water and isopropyl alcohol mixture was studied. The stock was a diesel fuel distillate with a solid point of -12/sup 0/C. Experiments were performed with a 3.5:1 volume ratio of urea solution to feed, urea content 38% by weight, isopropyl alcohol concentration 70% by weight, adduct formation temperature 55-30/sup 0/C, and adduct formation duration 30 min. Test results show the adverse effects at different quantities of cyanuric and biuret acids on adduct formation. Solutions for overcoming these effects are proposed.

  19. Improved process for the production of cellulose sulfate using sulfuric acid/ethanol solution.

    PubMed

    Chen, Guo; Zhang, Bin; Zhao, Jun; Chen, Hongwen

    2013-06-01

    An improved process for production of cellulose sulfate (CS) was developed by using sulfuric acid/ethanol solution as sulfonating agent and Na2SO4 as water absorbent. The FTIR, SEM and TG analysis were used to characterize the CS prepared. The total degree of substitution and viscosity of the product solution (2%, w/v) were ranging from 0.28 to 0.77 and from 115 to 907 mPa s, respectively, by changing the process parameters such as the amount of Na2SO4, the reaction time, the temperature, the sulfuric acid/alcohol ratio and liquid/solid ratio. The results indicated that the product with DS (0.28-0.77) and η2% (115-907) mPa s could be produced by using this improved process and more cellulose sulfate could be produced when cellulose was sulfonated for 3-4 h at -2 °C in sulfuric acid/ethanol (1.4-1.6) solution with addition of 0.8 g Na2SO4. The (13)C NMR indicated that the sulfate group of CS produced using sulfuric acid/ethanol solution was at C6 position.

  20. Long-term stability of earthen materials in contact with acidic tailings solutions

    SciTech Connect

    Peterson, S.R.; Erikson, R.L.; Gee, G.W.

    1982-11-01

    The objectives of the studies documented in this report were to use experimental and geochemical computer modeling tools to assess the long-term environmental impact of leachate movement from acidic uranium mill tailings. Liner failure (i.e., an increase in the permeability of the liner material) was not found to be a problem when various acidic tailings solutions leached through liner materials for periods up to 3 years. On the contrary, materials that contained over 30% clay showed a decrease in permeability with time in the laboratory columns. The high clay materials tested appear suitable for lining tailings impoundment ponds. The decreases in permeability are attributed to pore plugging resulting from the precipitation of minerals and solids. This precipitation takes place due to the increase in pH of the tailings solution brought about by the buffering capacity of the soil. Geochemical modeling predicts, and x-ray characterization confirms, that precipitation of solids from solution is occurring in the acidic tailings solution/liner interactions studied. In conclusion the same mineralogical changes and contaminant reactions predicted by geochemical modeling and observed in laboratory studies were found at a drained evaporation pond (Lucky Mc in Wyoming) with a 4 year history of acid attack.

  1. [Effects of UV Radiation on the Physicochemical Properties and Coagulation Properties of Humic Acid Solution].

    PubMed

    Wang, Wen-dong; Zhang, Ke; Fan, Qing-hai; Zheng, Dan

    2016-03-15

    To investigate the mechanism of UV light in promoting the removal of humic acid ( HA) by coagulation, the variations of the physical and chemical properties of the HA solution before and after UV light radiation were investigated. The effects of the changes in water quality conditions on the removal performance of HA in coagulation were also observed. Experimental results showed that except zeta potential, pH, chromaticity and viscosity of the HA solution exhibited varying degrees of decline after UV radiation. Further study showed that the impact of changes in viscosity of the solution on humic acid coagulation performance was relatively small. Under acidic conditions, the coagulation performance of HA significantly increased. The increase of zeta potential led to easy gathering of colloidal particles and improved the coagulation performance. Furthermore, except for HA with relative molecular mass of between (10-30) x 10³ and less than 10³, there was little variation in the proportion of low molecular weight HA, which may be an important reason that the coagulation performance of the humic acid solution increased after UV radiation. PMID:27337892

  2. Solution structures of europium(III) complexes of ethylenediaminetetraacetic acid

    SciTech Connect

    Latva, M.; Kankara, J.; Haapakka, K.

    1996-04-01

    Coordination of ethylenediaminetetraacetic acid (EDTA) with europium(III) has been studied at different concentrations in solution using {sup 7}F{sub 0}{yields}{sup 5}D{sub 0} excitation spectroscopy and excited-state lifetime measurements. EDTA forms with Eu(III) ion three different species in equimolar solutions at room temperature. At low pH values EuEDTAH is formed and at higher pH values than 1.5 two EuEDTA{sup -} complexes, which differ from each other with one water molecule in the first coordination sphere of the Eu(III) ion, total coordination number and coordination geometry, are also formed. When the concentration of EDTA is higher than the concentration of Eu(III), an EuEDTA(EDTAH){sup 4-} species where the second EDTA is weakly coordinated to EuEDTA{sup -}, is formed. If the concentration of Eu(III) ion is higher than EDTA, the extra Eu(III) ions associate with EuEDTA{sup -} and link to one of the carboxylate groups of EDTA thus causing a shortening of the excited-state lifetime of the EuEDTA{sup -} complex.

  3. Thermal stability of 5-o-caffeoylquinic acid in aqueous solutions at different heating conditions.

    PubMed

    Dawidowicz, Andrzej L; Typek, Rafal

    2010-12-22

    Chlorogenic acid is a naturally occurring phenolic compound found in all higher plants. This component, being the ester of caffeic acid with quinic acid, is an important biosynthetic intermediate and plays an important role in the plant's response to stress. Potential uses of chlorogenic acid are suggested in pharmaceuticals, foodstuffs, feed additives, and cosmetics due to its recently discovered biomedical activity. This finding caused new interest in chlorogenic acid properties, its isomers, and its natural occurrence. It has been found that as many as nine compounds (chlorogenic acid derivatives and its reaction product with water) can be formed from 5-o-caffeoylquinic acid during the heating of its water solution. Three of them, two hydroxylated 5-o-caffeoylquinic acid derivatives and 4,5-dicaffeoylquinic acid, have been not reported, yet. The amount of each formed component depends on the heating time and temperature. The presented results are important for researchers investigating plant metabolism and looking for new plant components. The transformation product can be mistakenly treated as a new component, not found before in the examined plant, or can be a cause of erroneous quantitative estimations of plant composition.

  4. Effect of tritium on corrosion behavior of chromium in 0.01 N sulfuric acid solution

    SciTech Connect

    Oyaidzu, M.; Isobe, K.; Hayashi, T.

    2015-03-15

    The effects of tritium on the corrosion behavior of chromium in 0.01 N sulfuric solution have been investigated in the present study. Electrochemical experiments have been carried our for pure chromium. At first, the concentration dependence of sulfuric acid solution on anodic polarization behavior of chromium was experimented, resulting in that 0.01 N one was found appropriate. The dependence of both dissolved oxygen and tritium concentration on anodic behavior of chromium were performed. It was found from that the self-passivation of chromium induced by dissolved oxygen was inhibited in tritiated solution resulting in the enhancement of the corrosion. As a consequence it is highly likely that the elution of chromium by highly oxidative radiolysis products would explain the passivation inhibitory effect of SUS304 stainless steel observed in tritiated solutions.

  5. Influence of uranium on corrosion of stainless steel in solutions of fluoride in nitric acid

    SciTech Connect

    Kurtenov, M.M.

    1985-09-01

    Stainless steels corrode rapidly in solutions of fluoride in nitric acid; the higher the fluoride ion content, the more intense is the corrosion. The activating effect of the fluoride ions mainly reduces to dissolution of the oxide films. Small amounts somewhat retard the cathodic reduction of HNO/sub 3/. In this report the authors provide the results of an investigation of the influence of uranium ions on the corrosion-electrochemical behavior of stainless steel 12Kh18N10T in solutions of up to 10 moles/liter of HNO/sub 3/, with fluoride ions up to 0.1 mole/liter. The authors conclude that the retardation of corrosion of stainless steel by uranium, zirconium and aluminum ions in solutions of fluorides in nitric acid is mainly due to the formation of strong complexes of these metals with fluorine ions, leading to a reduction of the number of free HF molecules in the solution. The stronger the complex of metal with fluorine, the higher the corrosion resistance of the stainless steel in a solution of fluoride in nitric acid.

  6. Spectrofluorimetric study of the interaction of ciprofloxacin with amino acids in aqueous solution following solvatochromic studies

    NASA Astrophysics Data System (ADS)

    Alizadeh, Kamal; Mobarrez, Mahsa; Ganjali, Mohammad Reza; Norouzi, Parviz; Chaichi, Mohammad Javad

    Complexation of a fluoroquinolone derivative (ciprofloxacin), L, and some amino acids has been studied using spectrofluorimetric method. Results indicated that ciprofloxacin have a greater tendency to form a 1:1 complex with aspartic acid and arginine than the other tested molecules. The fluorescence of ciprofloxacin exhibits quenching process while it has been titrated with these amino acids. Formation constant values (Kf) for complex formed between ciprofloxacin and amino acids were also calculated. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were studied too. Possible reasons for the observed stability sequence were discussed based on the structures proposed for the resulting complexes. Besides the solution studies, solvatochromic properties of the ciprofloxacin are discussed by studying its spectra in a selection of different solvents.

  7. Effect of tannic acid solution on collagen structures for dental restoration.

    PubMed

    Natsir, N; Wakasa, K; Yoshida, Y; Satou, N; Shintani, H

    1999-08-01

    This study examined the effect of tannic acid solution on dissolution of dentine collagen and morphological aspects of tendon collagen. Using root dentine, which was cut off from bovine anterior tooth, dentine powders were obtained by the pulverization and lyophilization. They were subject to an application of 1, 3, 5 or 10% tannic acid (TA) solution for 1, 3, 6, 12 or 24 h. TA-treated dentine powders were treated with 40% phosphoric acid (PA) for 30 s at 20 degrees C and additionally with trypsin. Released hydroxyproline in Woessner's assay after a hydrolysis in 6 N HCl at 110 degrees C for 20 h was assumed to be dissolved dentine collagen. Released hydroxyproline in a control sample without acid treatment decreased from 100 to about 60% with increased TA concentration of 1 to 10%, and decreased with increased incubation times of 1 to 24 h when applied by 5% TA solution. Scanning electron microscopy results established the morphological effect of their surface characteristics due to such treatments as 40% PA for 30 s and 5% TA for 6 h, or 40% PA after 5% TA treatment, yielding collagen structures protected by TA to attack from phosphoric acid.

  8. [Studies on carbonization of saccharides by using aqueous solution of various acids].

    PubMed

    Zhang, Xin; He, An-Qi; Kang, Ting-Guo; Xia, Jin-Ming; Weng, Shi-Fu; Xu, Yi-Zhuang; Wu, Jin-Guang

    2014-09-01

    The authors tried to establish an approach to use acids to convert biomass into a fuel with higher carbon content and lower oxygen content in a zero-energy-consumption fashion. Considering that biomass is composed of monosaccharide, we used aqueous solutions of variation acids including hydrochloric acid, sulfuric acid and perchloric acid to treat 2-deoxy-ribose and fructose at ambient temperature and pressure. Black substances were produced after a period of time when 2-deoxy-ribose and fructose were mixed with aqueous solutions containing 8 mol · L(-1) acids. The black substance was collected and characterized by using elemental analysis, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Elemental analysis results indicate that the contents of carbon increases significantly in the black substances in comparison with 2-deoxy-ribose and fructose. Moreover, XPS results indicate that the content of oxygen in the black substance undergoes a significant decrease compared with pure 2-deoxy-ribose and fructose. In the XPS spectra, the is peaks of 2-deoxy-ribose, strong sub peak at 286. 05 eV, which is assigned to carbon linked to oxygen directly, dominate in the C is peak envelop. After treatment by HClO4, the peak decreased dramatically. This result also supports the conclusion that the content of oxygen in mono-saccharide is significantly reduced after treatment by acids. In the FTIR spectra of the black substances, strong peaks can be observed around 1 600 cm(-1), indicating that C==C bond is formed in the product. The above results suggest that treatments with acids may be developed as a new zero-energy-consumption approach to convert biomass in a new fuel with improved energy output efficiency. PMID:25532323

  9. [Studies on carbonization of saccharides by using aqueous solution of various acids].

    PubMed

    Zhang, Xin; He, An-Qi; Kang, Ting-Guo; Xia, Jin-Ming; Weng, Shi-Fu; Xu, Yi-Zhuang; Wu, Jin-Guang

    2014-09-01

    The authors tried to establish an approach to use acids to convert biomass into a fuel with higher carbon content and lower oxygen content in a zero-energy-consumption fashion. Considering that biomass is composed of monosaccharide, we used aqueous solutions of variation acids including hydrochloric acid, sulfuric acid and perchloric acid to treat 2-deoxy-ribose and fructose at ambient temperature and pressure. Black substances were produced after a period of time when 2-deoxy-ribose and fructose were mixed with aqueous solutions containing 8 mol · L(-1) acids. The black substance was collected and characterized by using elemental analysis, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Elemental analysis results indicate that the contents of carbon increases significantly in the black substances in comparison with 2-deoxy-ribose and fructose. Moreover, XPS results indicate that the content of oxygen in the black substance undergoes a significant decrease compared with pure 2-deoxy-ribose and fructose. In the XPS spectra, the is peaks of 2-deoxy-ribose, strong sub peak at 286. 05 eV, which is assigned to carbon linked to oxygen directly, dominate in the C is peak envelop. After treatment by HClO4, the peak decreased dramatically. This result also supports the conclusion that the content of oxygen in mono-saccharide is significantly reduced after treatment by acids. In the FTIR spectra of the black substances, strong peaks can be observed around 1 600 cm(-1), indicating that C==C bond is formed in the product. The above results suggest that treatments with acids may be developed as a new zero-energy-consumption approach to convert biomass in a new fuel with improved energy output efficiency.

  10. Interaction of trace elements in acid mine drainage solution with humic acid.

    PubMed

    Suteerapataranon, Siripat; Bouby, Muriel; Geckeis, Horst; Fanghänel, Thomas; Grudpan, Kate

    2006-06-01

    The release of metal ions from a coal mining tailing area, Lamphun, Northern Thailand, is studied by leaching tests. Considerable amounts of Mn, Fe, Al, Ni and Co are dissolved in both simulated rain water (pH 4) and 10 mg L(-1) humic acid (HA) solution (Aldrich humic acid, pH 7). Due to the presence of oxidizing pyrite and sulfide minerals, the pH in both leachates decreases down to approximately 3 combined with high sulfate concentrations typical to acid mine drainage (AMD) water composition. Interaction of the acidic leachates upon mixing with ground- and surface water containing natural organic matter is simulated by subsequent dilution (1:100; 1:200; 1:300; 1:500) with a 10 mg L(-1) HA solution (ionic strength: 10(-3) mol L(-1)). Combining asymmetric flow field-flow fractionation (AsFlFFF) with UV/Vis and ICP-MS detection allows for the investigation of metal ion interaction with HA colloid and colloid size evolution. Formation of colloid aggregates is observed by filtration and AsFlFFF depending on the degree of the dilution. While the average HA size is initially found to be 2 nm, metal-HA complexes are always found to be larger. Such observation is attributed to a metal induced HA agglomeration, which is found even at low coverage of HA functional groups with metal ions. Increasing the metal ion to HA ratio, the HA bound metal ions and the HA entities are growing in size from <3 to >450 nm. At high metal ion to HA ratios, precipitation of FeOOH phases and HA agglomeration due to colloid charge neutralization by complete saturation of HA complexing sites are responsible for the fact that most of Fe and Al precipitate and are found in a size fraction >450 nm. In the more diluted solutions, HA is more relevant as a carrier for metal ion mobilization.

  11. The infrared optical constants of sulfuric acid at 250 K. [spectral reflectance measurement of aqueous solutions

    NASA Technical Reports Server (NTRS)

    Pinkley, L. W.; Williams, D.

    1976-01-01

    Results are presented for measurements of the IR spectral reflectance at near-normal incidence of aqueous solutions of sulfuric acid with acid concentrations of 75% and 95.6% by weight. Kramers-Kronig analyses of the reflectance data are employed to obtain values of the optical constants n(nu) and k(nu) in the spectral range from 400 to 6000 cm to the -1 power. The optical constants of these solutions at 250 K and 300 K are compared. It is found that in spectral regions remote from strong absorption bands, the values of the n(nu) indices obtained at 250 K agree with the values given by Lorentz-Lorenz correction of the same indices at 300 K. All absorption bands observed at 300 K are found to be present at 250 K with slight shifts in frequency and with significant differences in the k(nu) indices at the band maxima. Based on these results, it is concluded that the clouds of Venus probably consist of droplets of aqueous solutions of sulfuric acid with acid concentrations of about 75% by weight.

  12. Corrosion property of 9Cr-ODS steel in nitric acid solution for spent nuclear fuel reprocessing

    SciTech Connect

    Takeuchi, M.; Koizumi, T.; Inoue, M.; Koyama, S.I.

    2013-07-01

    Corrosion tests of oxide dispersion strengthened with 9% Cr (9Cr-ODS) steel, which is one of the desirable materials for cladding tube of sodium-cooled fast reactors, in pure nitric acid solution, spent FBR fuel solution, and its simulated solution were performed to understand the corrosion behavior in a spent nuclear fuel reprocessing. In this study, the 9Cr-ODS steel with lower effective chromium content was evaluated to understand the corrosion behavior conservatively. As results, the tube-type specimens of the 9Cr-ODS steels suffered severe weight loss owing to active dissolution at the beginning of the immersion test in pure nitric acid solution in the range from 1 to 3.5 M. In contrast, the weight loss was decreased and they showed a stable corrosion in the higher nitric acid concentration, the dissolved FBR fuel solution, and its simulated solution by passivation. The corrosion rates of the 9Cr-ODS steel in the dissolved FBR fuel solution and its simulated solution were 1-2 mm/y and showed good agreement with each other. The passivation was caused by the shift of corrosion potential to noble side owing to increase in nitric acid concentration or oxidative ions in the dissolved FBR fuel solution and the simulated spent fuel solution. (authors)

  13. Radiolysis of aqueous solutions of acetic acid in the presence of Na-montmorillonite

    NASA Technical Reports Server (NTRS)

    Navarro-Gonzalez, R.; Negron-Mendoza, A.; Ramos, S.; Ponnamperuma, C.

    1990-01-01

    The gamma-irradiation of 0.8 mol dm-3 aqueous, oxygen-free acetic acid solutions was investigated in the presence or absence of Na-montmorillonite. H2, CH4, CO, CO2, and several polycarboxylic acids were formed in all systems. The primary characteristics observed in the latter system were: (1) Higher yield of the decomposition of acetic acid; (2) Lower yield of the formation of polycarboxylic acids; (3) No effect on the formation of methane; (4) Higher yield of the formation of carbon dioxide; and (5) The reduction of Fe3+ in the octahedral sites of Na-montmorillonite. A possible reaction scheme was proposed to account for the observed changes. The results are important in understanding heterogeneous processes in radiation catalysis and might be significant to prebiotic chemistry.

  14. Aquatic photolysis: photolytic redox reactions between goethite and adsorbed organic acids in aqueous solutions

    USGS Publications Warehouse

    Goldberg, M.C.; Cunningham, K.M.; Weiner, Eugene R.

    1993-01-01

    Photolysis of mono and di-carboxylic acids that are adsorbed onto the surface of the iron oxyhydroxide (goethite) results in an oxidation of the organic material and a reduction from Fe(III) to Fe(II) in the iron complex. There is a subsequent release of Fe2+ ions into solution. At constant light flux and constant solution light absorption, the factors responsible for the degree of photolytic reaction include: the number of lattice sites that are bonded by the organic acid; the rate of acid readsorption to the surface during photolysis; the conformation and structure of the organic acid; the degree of oxidation of the organic acid; the presence or absence of an ??-hydroxy group on the acid, the number of carbons in the di-acid chain and the conformation of the di-acid. The ability to liberate Fe(III) at pH 6.5 from the geothite lattice is described by the lyotropic series: tartrate>citrate> oxalate > glycolate > maleate > succinate > formate > fumarate > malonate > glutarate > benzoate = butanoate = control. Although a larger amount of iron is liberated, the series is almost the same at pH 5.5 except that oxalate > citrate and succinate > maleate. A set of rate equations are given that describe the release of iron from the goethite lattice. It was observed that the pH of the solution increases during photolysis if the solutions are not buffered. There is evidence to suggest the primary mechanism for all these reactions is an electron transfer from the organic ligand to the Fe(III) in the complex. Of all the iron-oxyhydroxide materials, crystalline goethite is the least soluble in water; yet, this study indicates that in an aqueous suspension, iron can be liberated from the goethite lattice. Further, it has been shown that photolysis can occur in a multiphase system at the sediment- water interface which results in an oxidation of the organic species and release of Fe2+ to solution where it becomes available for further reaction. ?? 1993.

  15. Three-dimensional patterns from the thin-film drying of amino acid solutions

    PubMed Central

    Zhang, Xuehua; Crivoi, Alexandru; Duan, Fei

    2015-01-01

    Experimental atomic force microscopy (AFM) images show the dried-in patterns from amino acid solutions which can be in the form of dots or networks. The three-dimensional lattice-gas Kinetic Monte Carlo (KMC) model is applied to simulate the formation of dot-like and network-like particle structures from the evaporating thin films of solutions. A sigmoidal jump in the chemical potential value is implemented to obtain dual-scale structures with the grain size distribution peaking at two distinctive values. The simulated and experimental results are qualitatively comparable. PMID:26039636

  16. Influence of acidic and alkaline waste solution properties on uranium migration in subsurface sediments

    NASA Astrophysics Data System (ADS)

    Szecsody, Jim E.; Truex, Mike J.; Qafoku, Nikolla P.; Wellman, Dawn M.; Resch, Tom; Zhong, Lirong

    2013-08-01

    This study shows that acidic and alkaline wastes co-disposed with uranium into subsurface sediments have significant impact on changes in uranium retardation, concentration, and mass during downward migration. For uranium co-disposal with acidic wastes, significant rapid (i.e., hours) carbonate and slow (i.e., 100 s of hours) clay dissolution resulted, releasing significant sediment-associated uranium, but the extent of uranium release and mobility change was controlled by the acid mass added relative to the sediment proton adsorption capacity. Mineral dissolution in acidic solutions (pH 2) resulted in a rapid (< 10 h) increase in aqueous carbonate (with Ca2 +, Mg2 +) and phosphate and a slow (100 s of hours) increase in silica, Al3 +, and K+, likely from 2:1 clay dissolution. Infiltration of uranium with a strong acid resulted in significant shallow uranium mineral dissolution and deeper uranium precipitation (likely as phosphates and carbonates) with downward uranium migration of three times greater mass at a faster velocity relative to uranium infiltration in pH neutral groundwater. In contrast, mineral dissolution in an alkaline environment (pH 13) resulted in a rapid (< 10 h) increase in carbonate, followed by a slow (10 s to 100 s of hours) increase in silica concentration, likely from montmorillonite, muscovite, and kaolinite dissolution. Infiltration of uranium with a strong base resulted in not only uranium-silicate precipitation (presumed Na-boltwoodite) but also desorption of natural uranium on the sediment due to the high ionic strength solution, or 60% greater mass with greater retardation compared with groundwater. Overall, these results show that acidic or alkaline co-contaminant disposal with uranium can result in complex depth- and time-dependent changes in uranium dissolution/precipitation reactions and uranium sorption, which alter the uranium migration mass, concentration, and velocity.

  17. Influence of acidic and alkaline waste solution properties on uranium migration in subsurface sediments.

    PubMed

    Szecsody, Jim E; Truex, Mike J; Qafoku, Nikolla P; Wellman, Dawn M; Resch, Tom; Zhong, Lirong

    2013-08-01

    This study shows that acidic and alkaline wastes co-disposed with uranium into subsurface sediments have significant impact on changes in uranium retardation, concentration, and mass during downward migration. For uranium co-disposal with acidic wastes, significant rapid (i.e., hours) carbonate and slow (i.e., 100 s of hours) clay dissolution resulted, releasing significant sediment-associated uranium, but the extent of uranium release and mobility change was controlled by the acid mass added relative to the sediment proton adsorption capacity. Mineral dissolution in acidic solutions (pH2) resulted in a rapid (<10 h) increase in aqueous carbonate (with Ca(2+), Mg(2+)) and phosphate and a slow (100 s of hours) increase in silica, Al(3+), and K(+), likely from 2:1 clay dissolution. Infiltration of uranium with a strong acid resulted in significant shallow uranium mineral dissolution and deeper uranium precipitation (likely as phosphates and carbonates) with downward uranium migration of three times greater mass at a faster velocity relative to uranium infiltration in pH neutral groundwater. In contrast, mineral dissolution in an alkaline environment (pH13) resulted in a rapid (<10h) increase in carbonate, followed by a slow (10 s to 100 s of hours) increase in silica concentration, likely from montmorillonite, muscovite, and kaolinite dissolution. Infiltration of uranium with a strong base resulted in not only uranium-silicate precipitation (presumed Na-boltwoodite) but also desorption of natural uranium on the sediment due to the high ionic strength solution, or 60% greater mass with greater retardation compared with groundwater. Overall, these results show that acidic or alkaline co-contaminant disposal with uranium can result in complex depth- and time-dependent changes in uranium dissolution/precipitation reactions and uranium sorption, which alter the uranium migration mass, concentration, and velocity.

  18. Influence of acidic and alkaline waste solution properties on uranium migration in subsurface sediments.

    PubMed

    Szecsody, Jim E; Truex, Mike J; Qafoku, Nikolla P; Wellman, Dawn M; Resch, Tom; Zhong, Lirong

    2013-08-01

    This study shows that acidic and alkaline wastes co-disposed with uranium into subsurface sediments have significant impact on changes in uranium retardation, concentration, and mass during downward migration. For uranium co-disposal with acidic wastes, significant rapid (i.e., hours) carbonate and slow (i.e., 100 s of hours) clay dissolution resulted, releasing significant sediment-associated uranium, but the extent of uranium release and mobility change was controlled by the acid mass added relative to the sediment proton adsorption capacity. Mineral dissolution in acidic solutions (pH2) resulted in a rapid (<10 h) increase in aqueous carbonate (with Ca(2+), Mg(2+)) and phosphate and a slow (100 s of hours) increase in silica, Al(3+), and K(+), likely from 2:1 clay dissolution. Infiltration of uranium with a strong acid resulted in significant shallow uranium mineral dissolution and deeper uranium precipitation (likely as phosphates and carbonates) with downward uranium migration of three times greater mass at a faster velocity relative to uranium infiltration in pH neutral groundwater. In contrast, mineral dissolution in an alkaline environment (pH13) resulted in a rapid (<10h) increase in carbonate, followed by a slow (10 s to 100 s of hours) increase in silica concentration, likely from montmorillonite, muscovite, and kaolinite dissolution. Infiltration of uranium with a strong base resulted in not only uranium-silicate precipitation (presumed Na-boltwoodite) but also desorption of natural uranium on the sediment due to the high ionic strength solution, or 60% greater mass with greater retardation compared with groundwater. Overall, these results show that acidic or alkaline co-contaminant disposal with uranium can result in complex depth- and time-dependent changes in uranium dissolution/precipitation reactions and uranium sorption, which alter the uranium migration mass, concentration, and velocity. PMID:23851265

  19. Influence of Acidic and Alkaline Waste Solution Properties on Uranium Migration in Subsurface Sediments

    SciTech Connect

    Szecsody, James E.; Truex, Michael J.; Qafoku, Nikolla; Wellman, Dawn M.; Resch, Charles T.; Zhong, Lirong

    2013-08-01

    This study shows that acidic and alkaline wastes co-disposed with uranium into subsurface sediments has significant impact on changes in uranium retardation, concentration, and mass during downward migration. For uranium co-disposal with acidic wastes, significant rapid (i.e., hours) carbonate and slow (i.e., 100s of hours) clay dissolution resulted, releasing significant sediment-associated uranium, but the extent of uranium release and mobility change was controlled by the acid mass added relative to the sediment proton adsorption capacity. Mineral dissolution in acidic solutions (pH 2) resulted in a rapid (< 10 h) increase in aqueous carbonate (with Ca2+, Mg2+) and phosphate and a slow (100s of hours) increase in silica, Al3+, and K+, likely from 2:1 clay dissolution. Infiltration of uranium with a strong acid resulted in significant shallow uranium mineral dissolution and deeper uranium precipitation (likely as phosphates and carbonates) with downward uranium migration of three times greater mass at a faster velocity relative to uranium infiltration in pH neutral groundwater. In contrast, mineral dissolution in an alkaline environment (pH 13) resulted in a rapid (< 10 h) increase in carbonate, followed by a slow (10s to 100s of hours) increase in silica concentration, likely from montmorillonite, muscovite, and kaolinite dissolution. Infiltration of uranium with a strong base resulted in uranium-silicate precipitation (presumed Na-boltwoodite) but also desorption of natural uranium on the sediment due to the high ionic strength solution, or 60% greater mass with greater retardation compared with groundwater. Overall, these results show that acidic or alkaline co-contaminant disposal with uranium can result in complex depth- and time-dependent changes in uranium dissolution/precipitation reactions and uranium sorption, which alter the uranium migration mass, concentration, and velocity.

  20. Comparing the Titrations of Mixed-Acid Solutions Using Dropwise and Constant-Flow Techniques

    NASA Astrophysics Data System (ADS)

    Charlesworth, Paul; Seguin, Matthew J.; Chesney, David J.

    2003-11-01

    A mixed-acid solution containing hydrochloric and phosphoric acids was used to determine the error associated with performing a real-time titration. The results were compared against those obtained by performing the titration in a more traditional dropwise addition of titrant near the equivalence points. It was found that the real-time techniques resulted in significantly decreased analysis times while maintaining a low experimental error. The constant-flow techniques were implemented into two different levels of chemistry. It was found that students could successfully utilize the modified experiments. Problems associated with the techniques, major sources of error, and their solutions are discussed. In both cases, the use of the constant-flow setup has increased student recollection of key concepts, such as pKa determination, proper indicator choice, and recognizing the shape of specific titration curves by increasing student interest in the experiment.

  1. Infusion of branched-chain enriched amino acid solution in patients with hepatic encephalopathy.

    PubMed

    Freund, H; Dienstag, J; Lehrich, J; Yoshimura, N; Bradford, R R; Rosen, H; Atamian, S; Slemmer, E; Holroyde, J; Fischer, J E

    1982-08-01

    and 47% in the acute hepatitis group. Encephalopathy appeared to correlate with individual amino acids differentially in the various groups and with the ratio between the aromatic and the branched-chain amino acids. Ammonia did not correlate with either the degree of encephalopathy or improvement therefrom. In 24 Patients therapy for hepatic encephalopathy was limited to infusion of the branched-chain enriched amino acid solution only, with wake-up in 66% of this group. The results strongly suggest that in protein intolerant patients requiring nutritional support, infusion with branchedchain enriched amino acid solutions is well tolerated with either no worsening of or improvement in hepatic encephalopathy coincident with the achievement of nitrogen equilibrium and adequate nutritional support. PMID:6284073

  2. Large-scale production of anhydrous nitric acid and nitric acid solutions of dinitrogen pentoxide

    DOEpatents

    Harrar, Jackson E.; Quong, Roland; Rigdon, Lester P.; McGuire, Raymond R.

    2001-01-01

    A method and apparatus are disclosed for a large scale, electrochemical production of anhydrous nitric acid and N.sub.2 O.sub.5. The method includes oxidizing a solution of N.sub.2 O.sub.4 /aqueous-HNO.sub.3 at the anode, while reducing aqueous HNO.sub.3 at the cathode, in a flow electrolyzer constructed of special materials. N.sub.2 O.sub.4 is produced at the cathode and may be separated and recycled as a feedstock for use in the anolyte. The process is controlled by regulating the electrolysis current until the desired products are obtained. The chemical compositions of the anolyte and catholyte are monitored by measurement of the solution density and the concentrations of N.sub.2 O.sub.4.

  3. A pulse radiolysis study of salicylic acid and 5-sulpho-salicylic acid in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Kishore, Kamal; Mukherjee, T.

    2006-01-01

    Reactions of H, OH, eaq- and some one-electron oxidants have been studied with salicylic acid and 5-sulpho-salicylic acid in aqueous solutions. Rate constants for the reaction of eaq- with these compounds were of the order of 10 9 dm 3 mol -1 s -1 and this reaction led to the formation of reducing radicals which could transfer electron to methyl viologen. Other one-electron reductants were not able to reduce these compounds. OH radicals reacted with these compounds by addition pathway with very high rate constants (>10 10 dm 3 mol -1 s -1) while O rad - radical anions could oxidize these molecules to give phenoxyl type of radicals. Amongst the one-electron oxidants, only N 3rad and SO 4rad - could oxidize salicylic acid while 5-sulpho-salicylic acid could be oxidized only by SO 4- radicals indicating that while one-electron reduction potential for semi-oxidized SA may be<1.33 V vs. NHE (the E o1 for N 3rad radical), it is more than 1.33 V vs. NHE for semi-oxidized SSA species.

  4. Effect of molecular structure of aniline-formaldehyde copolymers on corrosion inhibition of mild steel in hydrochloric acid solution.

    PubMed

    Zhang, Yan; Nie, Mengyan; Wang, Xiutong; Zhu, Yukun; Shi, Fuhua; Yu, Jianqiang; Hou, Baorong

    2015-05-30

    Aniline-formaldehyde copolymers with different molecular structures have been prepared and investigated for the purpose of corrosion control of mild steel in hydrochloric acid. The copolymers were synthesized by a condensation polymerization process with different ratios of aniline to formaldehyde in acidic precursor solutions. The corrosion inhibition efficiency of as-synthesized copolymers for Q235 mild steel was investigated in 1.0 mol L(-1) hydrochloric acid solution by weight loss measurement, potentiodynamic polarization, and electrochemical impedance spectroscopy, respectively. All the results demonstrate that as-prepared aniline-formaldehyde copolymers are efficient mixed-type corrosion inhibitors for mild steels in hydrochloric acid. The corrosion inhibition mechanism is discussed in terms of the role of molecular structure on adsorption of the copolymers onto the steel surface in acid solution.

  5. Uptake of Hypobromous Acid (HOBr) by Aqueous Sulfuric Acid Solutions: Low-Temperature Solubility and Reaction

    NASA Technical Reports Server (NTRS)

    Iraci, Laura T.; Michelsen, Rebecca R.; Ashbourn, Samatha F. M.; Rammer, Thomas A.; Golden, David M.

    2005-01-01

    Hypobromous acid (HOBr) is a key species linking inorganic bromine to the chlorine and odd hydrogen chemical families. We have measured the solubility of HOBr in 45 - 70 wt% sulfuric acid solutions representative of upper tropospheric and lower stratospheric aerosol composition. Over the temperature range 201 - 252 K, HOBr is quite soluble in sulfuric acid, with an effective Henry's law coefficient, H* = 10(exp 4) - 10(exp 7) mol/L/atm. H* is inversely dependent on temperature, with Delta H = -46.2 kJ/mol and Delta S = -106.2 J/mol/K for 55 - 70 wt% H2SO4 solutions. Our study includes temperatures which overlap both previous measurements of HOBr solubility. For uptake into aqueous 45 wt% H2SO4, the solubility can be described by log H* = 3665/T - 10.63. For 55 - 70 wt% H2SO4, log H* = 2412/T - 5.55. At temperatures colder than approx. 213 K, the solubility of HOBr in 45 wt% H2SO4 is noticeably larger than in 70 wt% H2SO4. The solubility of HOBr is comparable to that of HBr, indicating that upper tropospheric and lower stratospheric aerosols should contain equilibrium concentrations of HOBr which equal or exceed those of HBr. Our measurements indicate chemical reaction of HOBr upon uptake into aqueous sulfuric acid in the presence of other brominated gases followed by evolution of gaseous products including Br2O and Br2, particularly at 70 wt% H2SO4.

  6. Zirconium complexes with lactic acid in the solution and solid states

    NASA Astrophysics Data System (ADS)

    Demkowicz, Paul Andrew

    Lactic acid complexes of zirconium are used in a great number of industrial applications. Among these is their use as crosslinking agents for hydraulic fracturing fluids used in secondary oil recovery operations. Because of a poor understanding of zirconium lactate complex chemistry and crosslinking reactions, however, the design of superior fluid systems is often not guided by sound chemical principles and leads to empirical guesswork. Zirconium lactate solutions were characterized using Fourier transform infrared (FT-IR) spectroscopy, 1H, 13C, and 17O nuclear magnetic resonance (NMR) spectroscopy, and potentiometry. The results indicate that lactic acid is coordinated bidentate to zirconium via the alcohol and carboxylate groups. The average number of lactate ligands per zirconium ion is approximately 2 and is demonstrated to be relatively constant from pH 4--9. The lability of the lactate complexes increases as the pH is decreased. The NMR data reveal that there are both large and small complex molecules present in solution, with the size of the complex depending on the extent of zirconium hydrolysis. Large complexes consist of lactic acid coordinated to polynuclear zirconium hydroxy ions. The molecular size of these complexes is sufficient to hinder their tumbling in solution and cause broadening of the measured NMR signals. Small complexes involve lactic acid coordinated to hydroxylated species containing fewer zirconium ions, such that the rotational motion in solution is sufficiently rapid to result in narrow NMR signals. Zirconium lactate complexes were precipitated from solution and analyzed in the solid state using FT-IR spectroscopy, 13C magic angle spinning (MAS) NMR spectroscopy, elemental analysis, thermal gravitational analysis, and x-ray diffraction. Two distinct types of crystalline compounds were synthesized with four lactate ligands per zirconium ion. The coordination of lactic acid to zirconium is different in the two compounds, with one showing

  7. Unified molecular picture of the surfaces of aqueous acid, base, and salt solutions.

    PubMed

    Mucha, Martin; Frigato, Tomaso; Levering, Lori M; Allen, Heather C; Tobias, Douglas J; Dang, Liem X; Jungwirth, Pavel

    2005-04-28

    The molecular structure of the interfacial regions of aqueous electrolytes is poorly understood, despite its crucial importance in many biological, technological, and atmospheric processes. A long-term controversy pertains between the standard picture of an ion-free surface layer and the strongly ion specific behavior indicating in many cases significant propensities of simple inorganic ions for the interface. Here, we present a unified and consistent view of the structure of the air/solution interface of aqueous electrolytes containing monovalent inorganic ions. Molecular dynamics calculations show that in salt solutions and bases the positively charged ions, such as alkali cations, are repelled from the interface, whereas the anions, such as halides or hydroxide, exhibit a varying surface propensity, correlated primarily with the ion polarizability and size. The behavior of acids is different due to a significant propensity of hydronium cations for the air/solution interface. Therefore, both cations and anions exhibit enhanced concentrations at the surface and, consequently, these acids (unlike bases and salts) reduce the surface tension of water. The results of the simulations are supported by surface selective nonlinear vibrational spectroscopy, which reveals among other things that the hydronium cations are present at the air/solution interface. The ion specific propensities for the air/solution interface have important implications for a whole range of heterogeneous physical and chemical processes, including atmospheric chemistry of aerosols, corrosion processes, and bubble coalescence.

  8. Copper-Sulfate Pentahydrate as a Product of the Waste Sulfuric Acid Solution Treatment

    NASA Astrophysics Data System (ADS)

    Marković, Radmila; Stevanović, Jasmina; Avramović, Ljiljana; Nedeljković, Dragutin; Jugović, Branimir; Stajić-Trošić, Jasna; Gvozdenović, Milica

    2012-12-01

    The aim of this study is synthesis of copper-sulfate pentahydrate from the waste sulfuric acid solution-mother liquor generated during the regeneration process of copper bleed solution. Copper is removed from the mother liquor solution in the process of the electrolytic treatment using the insoluble lead anodes alloyed with 6 mass pct of antimony on the industrial-scale equipment. As the result of the decopperization process, copper is removed in the form of the cathode sludge and is precipitated at the bottom of the electrolytic cell. By this procedure, the content of copper could be reduced to the 20 mass pct of the initial value. Chemical characterization of the sludge has shown that it contains about 90 mass pct of copper. During the decopperization process, the very strong poison, arsine, can be formed, and the process is in that case terminated. The copper leaching degree of 82 mass pct is obtained using H2SO4 aqueous solution with the oxygen addition during the cathode sludge chemical treatment at 80 °C ± 5 °C. Obtained copper salt satisfies the requirements of the Serbian Standard for Pesticide, SRPS H.P1. 058. Therefore, the treatment of waste sulfuric acid solutions is of great economic and environmental interest.

  9. Organic amendments increase soil solution phosphate concentrations in an acid soil: A controlled environment study

    SciTech Connect

    Schefe, C.R.; Patti, A.F.; Clune, T.S.; Jackson, R.

    2008-04-15

    Soil acidification affects at least 4 million hectares of agricultural land in Victoria, Australia. Low soil pH can inhibit plant growth through increased soluble aluminum (Al) concentrations and decreased available phosphorus (P). The addition of organic amendments may increase P availability through competition for P binding sites, solubilization of poorly soluble P pools, and increased solution pH. The effect of two organic amendments (lignite and compost) on P solubility in an acid soil was determined through controlled environment (incubation) studies. Three days after the addition of lignite and compost, both treatments increased orthophosphate and total P measured in soil solution, with the compost treatments having the greatest positive effect. Increased incubation time (26 days) increased soil solution P concentrations in both untreated and amended soils, with the greatest effect seen in total P concentrations. The measured differences in solution P concentrations between the lignite- and compost-amended treatments were likely caused by differences in solution chemistry, predominantly solution pH and cation dynamics. Soil amendment with lignite or compost also increased microbial activity in the incubation systems, as measured by carbon dioxide respiration. Based on the results presented, it is proposed that the measured increase in soil solution P with amendment addition was likely caused by both chemical and biological processes, including biotic and abiotic P solubilization reactions, and the formation of soluble organic-metal complexes.

  10. HPLC monitoring of spontaneous non-linear peptidization dynamics of selected amino acids in solution.

    PubMed

    Godziek, Agnieszka; Maciejowska, Anna; Sajewicz, Mieczysław; Kowalska, Teresa

    2015-03-01

    This is our new study in a series of publications devoted to exploration of applicability of high-performance liquid chromatography (HPLC) to providing answers to difficult questions from the area of the reaction kinetics and mechanisms with non-linear reactions. Although an excellent analytical performance of HPLC is an indisputable fact, so far its performance as a tool in the kinetic and mechanistic studies has been tested to a lesser extent. In our earlier studies, spontaneous peptidization dynamics of amino acids in solution was demonstrated by means of HPLC upon a few amino acid examples, and on that basis a theoretical model has been developed, anticipating an interdependence of dynamics on chemical structures of amino acids involved. In order to expand the spectrum of experimentally investigated amino acid cases, in this study we present the results valid for three novel amino acids of significant life sciences importance, which differ in terms of peptidization dynamics. Experimental evidence originates from the achiral HPLC with the evaporative light scattering detection and MS detection. A conclusion is drawn that different spontaneous peptidization dynamics of amino acids may significantly influence chemical composition of proteins encountered in living organisms. Hence, a need emerges for systematic physicochemical studies on spontaneous non-linear peptidization dynamics of proteinogenic amino acids in liquid abiotic (but also in the biotic) systems.

  11. EXAFS study of the speciation of protactinium(V) in aqueous hydrofluoric acid solutions.

    PubMed

    De Sio, Stéphanie M; Wilson, Richard E

    2014-12-01

    The speciation of protactinium(V) in hydrofluoric acid (HF) solutions was studied using X-ray absorption spectroscopy. Extended X-ray absorption fine structure measurements were performed on an aqueous solution of 0.05 M protactinium(V) with various HF concentrations ranging from 0.5 to 27 M in order to probe the protactinium coordination sphere with respect to the identity and number of coordinating ligands. The resulting fits to the spectra suggest the presence of an eight-coordinate homoleptic fluoro complex in highly concentrated fluoride solutions (27 M), with equilibrium between seven- and eight-coordinate fluoro complexes at moderate acidities, and in more dilute solutions, results indicate that one water molecule is likely to replace a fluoride in the first coordination sphere, at a distance of 2.54-2.57 Å. Comparisons of this chemistry with group V metals, niobium and tantalum, are presented, and the potential implications for these results on the hydrolytic behavior of protactinium in aqueous systems are discussed.

  12. EXAFS study of the speciation of protactinium(V) in aqueous hydrofluoric acid solutions.

    PubMed

    De Sio, Stéphanie M; Wilson, Richard E

    2014-12-01

    The speciation of protactinium(V) in hydrofluoric acid (HF) solutions was studied using X-ray absorption spectroscopy. Extended X-ray absorption fine structure measurements were performed on an aqueous solution of 0.05 M protactinium(V) with various HF concentrations ranging from 0.5 to 27 M in order to probe the protactinium coordination sphere with respect to the identity and number of coordinating ligands. The resulting fits to the spectra suggest the presence of an eight-coordinate homoleptic fluoro complex in highly concentrated fluoride solutions (27 M), with equilibrium between seven- and eight-coordinate fluoro complexes at moderate acidities, and in more dilute solutions, results indicate that one water molecule is likely to replace a fluoride in the first coordination sphere, at a distance of 2.54-2.57 Å. Comparisons of this chemistry with group V metals, niobium and tantalum, are presented, and the potential implications for these results on the hydrolytic behavior of protactinium in aqueous systems are discussed. PMID:25389749

  13. ATR FT-IR H 2O spectra of acidic aqueous solutions. Insights about proton hydration

    NASA Astrophysics Data System (ADS)

    Śmiechowski, Maciej; Stangret, Janusz

    2008-04-01

    Proton hydration in aqueous solutions has been recently characterised in our laboratory by means of vibrational spectra of HDO isotopically diluted in H 2O [M. Śmiechowski, J. Stangret, J. Chem. Phys. 125 (2006) 204508]. Here, we attempt to study quantitatively H 2O spectra of acidic aqueous solutions. In principle, H 2O spectra provide more information about the structural state of water molecules, resulting from oscillator couplings in the system, but they are much more difficult in interpretation, when compared with HDO spectra. The spectra of aqueous solutions of monoprotic acids (HCl, HClO 4, HPF 6) have been measured by Attenuated Total Reflectance (ATR) FT-IR spectroscopy. Spectral data have been analysed in a way that led to removal of the contribution of bulk water, in order to separate the spectra of solute-affected water only. The analysis has been focused on the infinite dilution limit behaviour of the spectrum. Changes induced in the affected spectra by temperature have been studied for HPF 6 solutions at 25-45 °C. The stretching vibration fundamental has been found to be primarily affected by counter-anion. Proton-affected H 2O spectrum shows the presence of very wide absorption bands in the range, where bulk water shows negligible own absorption, rather than "absorption continua". They could be adequately resolved into analytical components. These bands have been unaffected by temperature and loosely correlated with the stretching fundamental, as indicated by 2D IR correlation spectra. All spectral effects of the studied acids on H 2O in solution have been quantitatively evidenced and discussed. They seem to be in accordance with the main conclusions about proton hydration derived from recent studies of HDO spectra mentioned above.

  14. Degradation of hydroxycinnamic acid mixtures in aqueous sucrose solutions by the Fenton process.

    PubMed

    Nguyen, Danny M T; Zhang, Zhanying; Doherty, William O S

    2015-02-11

    The degradation efficiencies and behaviors of caffeic acid (CaA), p-coumaric acid (pCoA), and ferulic acid (FeA) in aqueous sucrose solutions containing the mixture of these hydroxycinnamic acids (HCAs) were studied by the Fenton oxidation process. Central composite design and multiresponse surface methodology were used to evaluate and optimize the interactive effects of process parameters. Four quadratic polynomial models were developed for the degradation of each individual acid in the mixture and the total HCAs degraded. Sucrose was the most influential parameter that significantly affected the total amount of HCA degraded. Under the conditions studied there was a <0.01% loss of sucrose in all reactions. The optimal values of the process parameters for a 200 mg/L HCA mixture in water (pH 4.73, 25.15 °C) and sucrose solution (13 mass %, pH 5.39, 35.98 °C) were 77% and 57%, respectively. Regression analysis showed goodness of fit between the experimental results and the predicted values. The degradation behavior of CaA differed from those of pCoA and FeA, where further CaA degradation is observed at increasing sucrose and decreasing solution pH. The differences (established using UV/vis and ATR-FTIR spectroscopy) were because, unlike the other acids, CaA formed a complex with Fe(III) or with Fe(III) hydrogen-bonded to sucrose and coprecipitated with lepidocrocite, an iron oxyhydroxide. PMID:25585639

  15. Degradation of hydroxycinnamic acid mixtures in aqueous sucrose solutions by the Fenton process.

    PubMed

    Nguyen, Danny M T; Zhang, Zhanying; Doherty, William O S

    2015-02-11

    The degradation efficiencies and behaviors of caffeic acid (CaA), p-coumaric acid (pCoA), and ferulic acid (FeA) in aqueous sucrose solutions containing the mixture of these hydroxycinnamic acids (HCAs) were studied by the Fenton oxidation process. Central composite design and multiresponse surface methodology were used to evaluate and optimize the interactive effects of process parameters. Four quadratic polynomial models were developed for the degradation of each individual acid in the mixture and the total HCAs degraded. Sucrose was the most influential parameter that significantly affected the total amount of HCA degraded. Under the conditions studied there was a <0.01% loss of sucrose in all reactions. The optimal values of the process parameters for a 200 mg/L HCA mixture in water (pH 4.73, 25.15 °C) and sucrose solution (13 mass %, pH 5.39, 35.98 °C) were 77% and 57%, respectively. Regression analysis showed goodness of fit between the experimental results and the predicted values. The degradation behavior of CaA differed from those of pCoA and FeA, where further CaA degradation is observed at increasing sucrose and decreasing solution pH. The differences (established using UV/vis and ATR-FTIR spectroscopy) were because, unlike the other acids, CaA formed a complex with Fe(III) or with Fe(III) hydrogen-bonded to sucrose and coprecipitated with lepidocrocite, an iron oxyhydroxide.

  16. Electrical properties of polarizable ionic solutions. II. Computer simulation results

    NASA Astrophysics Data System (ADS)

    Caillol, J. M.; Levesque, D.; Weis, J. J.

    1989-11-01

    We present molecular dynamics simulations for two limiting models of ionic solutions: one where the solvent molecules are polar, but nonpolarizable; the other where they are only polarizable (but have no permanent dipole moment). For both models, the static two-body correlation functions, the frequency-dependent dielectric constant and conductivity are calculated and the statistical uncertainty on these quantities estimated for molecular dynamics runs of the order of 105 integration steps. For the case of the polar solvent, the accuracy of the computed static interionic correlation functions allows a valuable test of the hypernetted chain integral equation theory at an ionic concentration of 0.04. The quantitative variation of the fluctuations of polarization and electrical current with change of boundary conditions is evaluated within the context of the second model (polarizable nonpolar solvent). Applying the relationships derived in Part I between the phenomenological coefficients and susceptibilities, it is shown that consistent values for the dielectric constant and electrical conductivity are obtained. The sum rules which generalize the Stillinger-Lovett conditions to ionic solutions are computed and shown to be satisfied in our simulations. The evaluation of these sum rules constitutes an important test of the convergence of the electrolyte system to an equilibrium state.

  17. Role of Organic Acids in Bioformation of Kaolinite: Results of Laboratory Experiments

    NASA Astrophysics Data System (ADS)

    Bontognali, T. R. R.; Vasconcelos, C.; McKenzie, J. A.

    2012-04-01

    Clay minerals and other solid silica phases have a broad distribution in the geological record and greatly affect fundamental physicochemical properties of sedimentary rocks, including porosity. An increasing number of studies suggests that microbial activity and microbially produced organic acids might play an important role in authigenic clay mineral formation, at low temperatures and under neutral pH conditions. In particular, early laboratory experiments (Linares and Huertas, 1971) reported the precipitation of kaolinite in solutions of SiO2 and Al2O3 with different molar ratios SiO2/Al2O3, together with fulvic acid (a non-characterized mixture of many different acids containing carboxyl and phenolate groups) that was extracted from peat soil. Despite many attempts, these experiments could not be reproduced until recently. Fiore et al. (2011) hypothesized that the non-sterile fulvic acid might have contained microbes that participated in the formation of kaolinite. Using solutions saturated with Si and Al and containing oxalate and/or mixed microbial culture extracted from peat-moss soil, they performed incubation experiments, which produced kaolinite exclusively in solutions containing oxalate and microbes. We proposed to test the role of specific organic acids for kaolinite formation, conducting laboratory experiments at 25˚C, with solutions of sodium silicate, aluminum chloride and various organic compounds (i.e. EDTA, citric acid, succinic acid and oxalic acid). Specific organic acids may stabilize aluminum in octahedral coordination positions, which is crucial for the initial nucleation step. In our experiments, a poorly crystalline mineral that is possibly a kaolinite precursor formed exclusively in the presence of succinic acid. In experiments with other organic compounds, no incorporation of Al was observed, and amorphous silica was the only precipitated phase. In natural environments, succinic acid is produced by a large variety of microbes as an

  18. Competitive adsorption of boric acid and chromate onto alumina in aqueous solutions.

    PubMed

    Demetriou, A; Pashalidis, I

    2014-01-01

    The competitive adsorption of boric acid and chromate from aqueous solutions by alumina has been investigated by spectrophotometry at pH 8, ionic strength = 0.0, 0.1 and 1.0 M NaClO4, T = 22 ± 3 °C and under normal atmospheric conditions. The experimental data show that addition of excess boric acid in the system leads to the increase of Cr(VI) concentration in solution, indicating the replacement of adsorbed chromate by boron on the alumina surface. Data evaluation results in the determination of the competition reaction constant and the formation constant of the Cr(VI) surface complexes, which are logKCr(VI)-B(III) = -3.5 ± 0.2 and logβ*Cr = 7.6 ± 0.3, respectively.

  19. Evaluation of the Magnesium Hydroxide Treatment Process for Stabilizing PFP Plutonium/Nitric Acid Solutions

    SciTech Connect

    Gerber, Mark A.; Schmidt, Andrew J.; Delegard, Calvin H.; Silvers, Kurt L.; Baker, Aaron B.; Gano, Susan R.; Thornton, Brenda M.

    2000-09-28

    This document summarizes an evaluation of the magnesium hydroxide [Mg(OH)2] process to be used at the Hanford Plutonium Finishing Plant (PFP) for stabilizing plutonium/nitric acid solutions to meet the goal of stabilizing the plutonium in an oxide form suitable for storage under DOE-STD-3013-99. During the treatment process, nitric acid solutions bearing plutonium nitrate are neutralized with Mg(OH)2 in an air sparge reactor. The resulting slurry, containing plutonium hydroxide, is filtered and calcined. The process evaluation included a literature review and extensive laboratory- and bench-scale testing. The testing was conducted using cerium as a surrogate for plutonium to identify and quantify the effects of key processing variables on processing time (primarily neutralization and filtration time) and calcined product properties.

  20. Glucose metabolic flux distribution of Lactobacillus amylophilus during lactic acid production using kitchen waste saccharified solution

    PubMed Central

    Liu, Jianguo; Wang, Qunhui; Zou, Hui; Liu, Yingying; Wang, Juan; Gan, Kemin; Xiang, Juan

    2013-01-01

    The 13C isotope tracer method was used to investigate the glucose metabolic flux distribution and regulation in Lactobacillus amylophilus to improve lactic acid production using kitchen waste saccharified solution (KWSS). The results demonstrate that L. amylophilus is a homofermentative bacterium. In synthetic medium, 60.6% of the glucose entered the Embden–Meyerhof–Parnas (EMP) to produce lactic acid, whereas 36.4% of the glucose entered the pentose phosphate metabolic pathway (HMP). After solid–liquid separation of the KWSS, the addition of Fe3+ during fermentation enhanced the NADPH production efficiency and increased the NADH content. The flux to the EMP was also effectively increased. Compared with the control (60.6% flux to EMP without Fe3+ addition), the flux to the EMP with the addition of Fe3+ (74.3%) increased by 23.8%. In the subsequent pyruvate metabolism, Fe3+ also increased lactate dehydrogenase activity, and inhibited alcohol dehydrogenase, pyruvate dehydrogenase and pyruvate carboxylase, thereby increasing the lactic acid production to 9.03 g l−1, an increase of 8% compared with the control. All other organic acid by-products were lower than in the control. However, the addition of Zn2+ showed an opposite effect, decreasing the lactic acid production. In conclusion it is feasible and effective means using GC-MS, isotope experiment and MATLAB software to integrate research the metabolic flux distribution of lactic acid bacteria, and the results provide the theoretical foundation for similar metabolic flux distribution. PMID:23489617

  1. Glucose metabolic flux distribution of Lactobacillus amylophilus during lactic acid production using kitchen waste saccharified solution.

    PubMed

    Liu, Jianguo; Wang, Qunhui; Zou, Hui; Liu, Yingying; Wang, Juan; Gan, Kemin; Xiang, Juan

    2013-11-01

    The (13) C isotope tracer method was used to investigate the glucose metabolic flux distribution and regulation in Lactobacillus amylophilus to improve lactic acid production using kitchen waste saccharified solution (KWSS). The results demonstrate that L. amylophilus is a homofermentative bacterium. In synthetic medium, 60.6% of the glucose entered the Embden-Meyerhof-Parnas (EMP) to produce lactic acid, whereas 36.4% of the glucose entered the pentose phosphate metabolic pathway (HMP). After solid-liquid separation of the KWSS, the addition of Fe(3+) during fermentation enhanced the NADPH production efficiency and increased the NADH content. The flux to the EMP was also effectively increased. Compared with the control (60.6% flux to EMP without Fe(3+) addition), the flux to the EMP with the addition of Fe(3+) (74.3%) increased by 23.8%. In the subsequent pyruvate metabolism, Fe(3+) also increased lactate dehydrogenase activity, and inhibited alcohol dehydrogenase, pyruvate dehydrogenase and pyruvate carboxylase, thereby increasing the lactic acid production to 9.03 g l(-1) , an increase of 8% compared with the control. All other organic acid by-products were lower than in the control. However, the addition of Zn(2+) showed an opposite effect, decreasing the lactic acid production. In conclusion it is feasible and effective means using GC-MS, isotope experiment and MATLAB software to integrate research the metabolic flux distribution of lactic acid bacteria, and the results provide the theoretical foundation for similar metabolic flux distribution.

  2. Acid rain: Some preliminary results from global data analysis

    NASA Astrophysics Data System (ADS)

    Sequeira, R.

    1981-02-01

    Preliminary results of an analysis of global precipitation data from WMO (World Meteorological Organization) stations suggest that even remote maritime baseline stations, far removed from major continents, could become predisposed to acid rain if there is a deficiency of non-marine calcium relative to non-marine sulfate. The regional stations show greater complexity than the baseline stations in their precipitation chemistry. The overall results of this analysis suggest that not all non-marine sulfate and nitrate in precipitation could be present as acid.

  3. Viscometric study of chitosan solutions in acetic acid/sodium acetate and acetic acid/sodium chloride.

    PubMed

    Costa, Cristiane N; Teixeira, Viviane G; Delpech, Marcia C; Souza, Josefa Virginia S; Costa, Marcos A S

    2015-11-20

    A viscometric study was carried out at 25°C to assess the physical-chemical behavior in solution and the mean viscometric molar mass (M¯v) of chitosan solutions with different deacetylation degrees, in two solvent mixtures: medium 1-acetic acid 0.3mol/L and sodium acetate 0.2mol/L; and medium 2-acetic acid 0.1mol/L and sodium chloride 0.2mol/L. Different equations were employed, by graphical extrapolation, to calculate the intrinsic viscosities [η] and the viscometric constants, to reveal the solvent's quality: Huggins (H), Kraemer (K) and Schulz-Blaschke (SB). For single-point determination, the equations used were SB, Solomon-Ciuta (SC) and Deb-Chanterjee (DC), resulting in a faster form of analysis. The values of ̄M¯v were calculated by applying the equation of Mark-Houwink-Sakurada. The SB and SC equations were most suitable for single-point determination of [η] and ̄M¯v and the Schulz-Blachke constant (kSB), equal to 0.28, already utilized for various systems, can also be employed to analyze chitosan solutions under the conditions studied.

  4. Dose rate dependence of the speciation of neptunium in irradiated solutions of nitric acid

    SciTech Connect

    Precek, M.; Paulenova, A.; Mincher, B.J.; Mezyk, S.P.

    2013-07-01

    The effects of radiation on the redox speciation of neptunium are of interest due to their impact on the performance of separation of neptunium from highly radioactive solutions of dissolved used nuclear fuel. In this study, the influence of dose rate change from 0.4 kGy/h to 6 kGy/h was examined during irradiation of solutions of initially hexavalent 2.0-2.5 mM neptunium in nitric acid of two different concentrations (0.5 and 1 M). Results indicate that the immediate radiolytic steady-state concentration of neptunium(V) were depressed and its initial radiolytic yield was up to 2-times lower (in 1 M HNO{sub 3} solutions)during irradiations with the higher dose rate. The finding is explained on the basis of the enhancement of the role of oxidizing radicals during the radiolytic process. (authors)

  5. Ultrasonic degradation of oxalic acid in aqueous solutions.

    PubMed

    Dükkanci, M; Gündüz, G

    2006-09-01

    This paper describes the ultrasonic degradation of oxalic acid. The effects of ultrasonic power, H(2)O(2), NaCl, external gases on the degradation of oxalic acid were investigated. Reactor flask containing oxalic acid was immersed in the ultrasonic bath with water as the coupling fluid. Representative samples withdrawn were analysed by volumetric titration. Degradation degree of oxalic acid increased with increasing ultrasonic power. It was observed that H(2)O(2) has negative contribution on the degradation of oxalic acid and there was an optimum concentration of NaCl for enhancing the degradation degree of oxalic acid. Although bubbling nitrogen gave higher degradation than that for bubbling air, both gases (for 20 min before sonication and during sonication together) could not help to enhance the degradation of oxalic acid when compared with the degradation without gas passage. PMID:16352455

  6. Kinetic Aspects of Leaching Zinc from Waste Galvanizing Zinc by Using Hydrochloric Acid Solutions

    NASA Astrophysics Data System (ADS)

    Sminčáková, Emília; Trpčevská, Jarmila; Pirošková, Jana

    2016-10-01

    In this work, the results of acid leaching of flux skimmings coming from two plants are presented. Sample A contained two phases, Zn(OH)Cl and NH4Cl. In sample B, the presence of three phases, Zn5(OH)8Cl2·H2O, (NH4)2(ZnCl4) and ZnCl2(NH3)2, was proved. The aqueous solution of hydrochloric acid and distilled water was used as the leaching medium. The effects of the leaching time, temperature and concentration of the leaching medium on the zinc extraction were investigated. The apparent activation energy, E a = 4.61 kJ mol-1, and apparent reaction order n = 0.18 for sample A, and the values E a = 6.28 kJ mol-1 and n = 0.33 for sample B were experimentally determined. Zinc leaching in acid medium is a diffusion-controlled process.

  7. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  8. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  9. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  10. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  11. 49 CFR 173.229 - Chloric acid solution or chlorine dioxide hydrate, frozen.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Chloric acid solution or chlorine dioxide hydrate, frozen. 173.229 Section 173.229 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.229 Chloric acid solution or chlorine dioxide hydrate, frozen. When...

  12. Exceptionally crystalline and conducting acid doped polyaniline films by level surface assisted solution casting approach

    NASA Astrophysics Data System (ADS)

    Puthirath, Anand B.; Methattel Raman, Shijeesh; Varma, Sreekanth J.; Jayalekshmi, S.

    2016-04-01

    Emeraldine salt form of polyaniline (PANI) was synthesized by chemical oxidative polymerisation method using ammonium persulfate as oxidant. Resultant emeraldine salt form of PANI was dedoped using ammonia solution and then re-doped with camphor sulphonic acid (CSA), naphthaline sulphonic acid (NSA), hydrochloric acid (HCl), and m-cresol. Thin films of these doped PANI samples were deposited on glass substrates using solution casting method with m-cresol as solvent. A level surface was employed to get homogeneous thin films of uniform thickness. Detailed X-ray diffraction studies have shown that the films are exceptionally crystalline. The crystalline peaks observed in the XRD spectra can be indexed to simple monoclinic structure. FTIR and Raman spectroscopy studies provide convincing explanation for the exceptional crystallinity observed in these polymer films. FESEM and AFM images give better details of surface morphology of doped PANI films. The DC electrical conductivity of the samples was measured using four point probe technique. It is seen that the samples also exhibit quite high DC electrical conductivity, about 287 S/cm for CSA doped PANI, 67 S/cm for NSA doped PANI 65 S/cm for HCl doped PANI, and just below 1 S/cm for m-cresol doped PANI. Effect of using the level surface for solution casting is studied and correlated with the observed crystallinity.

  13. The electrochemical corrosion of bulk nanocrystalline ingot iron in acidic sulfate solution.

    PubMed

    Wang, S G; Shen, C B; Long, K; Zhang, T; Wang, F H; Zhang, Z D

    2006-01-12

    The corrosion properties of bulk nanocrystalline ingot iron (BNII) fabricated from conventional polycrystalline ingot iron (CPII) by severe rolling were investigated by means of immersion test, potentiodynamic polarization (PDP), electrochemical impedance spectroscopy (EIS) tests, and scanning electron microscopy (SEM) observation. These experimental results indicate that BNII possesses excellent corrosion resistance in comparison with CPII in acidic sulfate solution at room temperature. It may mainly result from different surface microstructures between CPII and BNII. However, the corrosion resistance of nanocrystalline materials is usually degraded because of their metastable microstructure nature, and the residual stress in nanocrystalline materials also can result in degradation of corrosion resistance according to the traditional point of view.

  14. Uptake of methacrolein into aqueous solutions of sulfuric acid and hydrogen peroxide.

    PubMed

    Liu, Ze; Wu, Ling-Yan; Wang, Tian-He; Ge, Mao-Fa; Wang, Wei-Gang

    2012-01-12

    Multiphase acid-catalyzed oxidation by hydrogen peroxide has been suggested to be a potential route to secondary organic aerosol (SOA) formation from isoprene and its gas-phase oxidation products, but the kinetics and chemical mechanism remain largely uncertain. Here we report the first measurement of uptake of methacrolein into aqueous solutions of sulfuric acid and hydrogen peroxide in the temperature range of 253-293 K. The steady-state uptake coefficients were acquired and increased quickly with increasing sulfuric acid concentration and decreasing temperature. Propyne, acetone, and 2,3-dihydroxymethacrylic acid were suggested as the products. The chemical mechanism is proposed to be the oxidation of carbonyl group and C═C double bonds by peroxide hydrogen in acidic environment, which could explain the large content of polyhydroxyl compounds in atmospheric fine particles. These results indicate that multiphase acid-catalyzed oxidation of methacrolein by hydrogen peroxide can contribute to SOA mass in the atmosphere, especially in the upper troposphere.

  15. Dixon resultant's solution of systems of geodetic polynomial equations

    NASA Astrophysics Data System (ADS)

    Paláncz, Béla; Zaletnyik, Piroska; Awange, Joseph L.; Grafarend, Erik W.

    2008-08-01

    The Dixon resultant is proposed as an alternative to Gröbner basis or multipolynomial resultant approaches for solving systems of polynomial equations inherent in geodesy. Its smallness in size, high density (ratio on the number of nonzero elements to the number of all elements), speed, and robustness (insensitive to combinatorial sequence and monomial order, e.g., Gröbner basis) makes it extremely attractive compared to its competitors. Using 3D-intersection and conformal C 7 datum transformation problems, we compare its performance to those of the Sturmfels’s resultant and Gröbner basis. For the 3D-intersection problem, Sturmfels’s resultant needed 0.578 s to solve a 6 × 6 resultant matrix whose density was 0.639, the Dixon resultant on the other hand took 0.266 s to solve a 4 × 4 resultant matrix whose density was 0.870. For the conformal C 7 datum transformation problem, the Dixon resultant took 2.25 s to compute a quartic polynomial in scale parameter whereas the computaton of the Gröbner basis fails. Using relative coordinates to compute the quartic polynomial in scale parameter, the Gröbner basis needed 0.484 s, while the Dixon resultant took 0.016 s. This highlights the robustness of the Dixon resultant (i.e., the capability to use both absolute and relative coordinates with any order of variables) as opposed to Gröbner basis, which only worked well with relative coordinates, and was sensitive to the combinatorial sequence and order of variables. Geodetic users uncomfortable with lengthy expressions of Gröbner basis or multipolynomial resultants, and who aspire to optimize on the attractive features of Dixon resultant, may find it useful.

  16. Corrosion Behavior of Alloy 22 in Chloride Solutions Containing Organic Acids

    SciTech Connect

    Carranza, R M; Giordano, C M; Rodr?guez, M A; Rebak, R B

    2005-11-04

    Alloy 22 (N06022) is a nickel based alloy containing alloying elements such as chromium, molybdenum and tungsten. It is highly corrosion resistant both under reducing and under oxidizing conditions. Electrochemical studies such as electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. Tests were also carried out in NaCl solutions containing oxalic acid or acetic acid. It is shown that the corrosion rate of Alloy 22 was higher in a solution containing oxalic acid than in a solution of the same pH acidified with HCl. Acetic acid was not corrosive to Alloy 22. The corrosivity of oxalic acid was attributed to its capacity to form stable complex species with metallic cations from Alloy 22.

  17. Properties of alkali-solubilized collagen solution crosslinked by N-hydroxysuccinimide activated adipic acid

    NASA Astrophysics Data System (ADS)

    Chen, Yihui; Zhang, Min; Liu, Wentao; Li, Guoying

    2011-03-01

    The effect of N-hydroxysuccinimide activated adipic acid (NHS-AA) on the properties of alkali-solubilized collagen solutions was examined. The residual amino group content in crosslinked collagen, determined by trinitrobenzensulfonic acid (TNBS) assay, was decreased with increasing NHS-AA concentration. The results from differential scanning calorimeter (DSC) indicated that the maximum denaturation temperature ( T d) of crosslinked collagen solution was about 4.2°C higher than that of un-crosslinked collagen solution (36.6°C). Moreover, the values of storage modulus ( G'), loss modulus ( G″) and complex viscosity ( η*), obtained by means of dynamic frequency sweeps, were increased as NHS-AA concentration added up to 1.5 mM, and then decreased slightly when further increased NHS-AA concentration. Besides, for collagen solution crosslinked with 1.5 mM NHS-AA, dynamic denaturation temperature ( T dd) was about 1.1°C lower than T d (40.8°C), and the Arrhenius-type time-temperature superposition (TTS) principle was applied to yield the activation energy to be 474.4 kJmol-1.

  18. A theoretical study on clusters of benzoic acid water in benzene solutions

    NASA Astrophysics Data System (ADS)

    Sagarik, Kritsana; Chaiwongwattana, Sermsiri; Sisot, Phittaya

    2004-11-01

    Structures and stability of benzoic acid dimer ((BA)2) and benzoic acid-water (BA-H2O) m:n complexes, with m and n = 1, 2, were studied in benzene solutions, using molecular dynamics (MD) simulations. It appeared that nearly all hydrogen bond (H-bond) complexes suggested from different partition experiments existed in MD simulations, with the probability depending on their size and temperature. The MD results revealed the probability of finding H-bonds between water molecules, as well as the non-self-association of water molecules in benzene solutions. Although the H-bonds in (BA)2 are quite strong in the gas phase and pure benzene, they can be opened by water molecules, forming microhydrates in benzene solutions. It was shown that, in order to provide insights into the structures and stability of the BA-H2O complexes in benzene solution, solvent molecules as well as dynamic and temperature effects have to be included in theoretical investigation.

  19. The ototoxic effect of boric acid solutions applied into the middle ear of guinea pigs.

    PubMed

    Oztürkcan, Sedat; Dündar, Riza; Katilmis, Hüseyin; Ilknur, Ali Ekber; Aktaş, Sinem; Haciömeroğlu, Senem

    2009-05-01

    This study analyzed the ototoxic effects of boric acid solutions. Boric acid solutions have been used as otologic preparations for many years. Boric acid is commonly found in solutions prepared with alcohol or distilled water but can also be found in a powder form. These preparations are used for both their antiseptic and acidic qualities in external and middle ear infections. We investigated the ototoxic effect of boric acid solutions on guinea pigs. We are unaware of any similar, previously published study of this subject in English. The study was conducted on 28 young albino guinea pigs. Prior to application of the boric acid solution under general anesthesia, an Auditory Brainstem Response (ABRs) test was applied to the right ear of the guinea pigs. Following the test, a perforation was created on the tympanic membrane of the right ear of each guinea pig and small gelfoam pieces were inserted into the perforated area. Test solutions were administered to the middle ear for 10 days by means of a transcanal route. Fifteen days after inserting the gelfoams in all of the guinea pigs, we anasthesized the guinea pigs and removed the gelfoams from the perforated region of the ear and then performed an ABRs on each guinea pig. The ABRs were within the normal range before the applications. After the application, no significant changes were detected in the ABRs thresholds in neither the saline group nor the group administered boric acid and distilled water solution; however, significant changes were detected in the ABRs thresholds of the Gentamicine and boric acid and alcohol solution groups. We believe that a 4% boric acid solution prepared with distilled water can be a more reliable preparation than a 4% boric acid solution prepared with alcohol.

  20. The standard enthalpies of formation of crystalline N-(carboxymethyl)aspartic acid and its aqueous solutions

    NASA Astrophysics Data System (ADS)

    Lytkin, A. I.; Chernyavskaya, N. V.; Volkov, A. V.; Nikol'Skii, V. M.

    2007-07-01

    The energy of combustion of N-(carboxymethyl)aspartic acid (CMAA) was determined by bomb calorimetry in oxygen. The standard enthalpies of combustion and formation of crystalline N-(carboxymethyl)aspartic acid were calculated. The heat effects of solution of crystalline CMAA in water and a solution of sodium hydroxide were measured at 298.15 K by direct calorimetry. The standard enthalpies of formation of CMAA and its dissociation products in aqueous solution were determined.

  1. The stability of the acetic acid dimer in microhydrated environments and in aqueous solution.

    PubMed

    Pašalić, Hasan; Tunega, Daniel; Aquino, Adélia J A; Haberhauer, Georg; Gerzabek, Martin H; Lischka, Hans

    2012-03-28

    The thermodynamic stability of the acetic acid dimer conformers in microhydrated environments and in aqueous solution was studied by means of molecular dynamics simulations using the density functional based tight binding (DFTB) method. To confirm the reliability of this method for the system studied, density functional theory (DFT) and second order Møller-Plesset perturbation theory (MP2) calculations were performed for comparison. Classical optimized potentials for liquid simulations (OPLS) force field dynamics was used as well. One focus of this work was laid on the study of the capabilities of water molecules to break the hydrogen bonds of the acetic acid dimer. The barrier for insertion of one water molecule into the most stable cyclic dimer is found to lie between 3.25 and 4.8 kcal mol(-1) for the quantum mechanical methods, but only at 1.2 kcal mol(-1) for OPLS. Starting from different acetic acid dimer structures optimized in gas phase, DFTB dynamics simulations give a different picture of the stability in the microhydrated environment (4 to 12 water molecules) as compared to aqueous solution. In the former case all conformers are converted to the hydrated cyclic dimer, which remains stable over the entire simulation time of 1 ns. These results demonstrate that the considered microhydrated environment is not sufficient to dissociate the acetic acid dimer. In aqueous solution, however, the DFTB dynamics shows dissociation of all dimer structures (or processes leading thereto) starting after about 50 ps, demonstrating the capability of the water environment to break up the relatively strong hydrogen bridges. The OPLS dynamics in the aqueous environment shows--in contrast to the DFTB results--immediate dissociation, but a similar long-term behavior.

  2. Mobbing Experiences of Instructors: Causes, Results, and Solution Suggestions

    ERIC Educational Resources Information Center

    Celep, Cevat; Konakli, Tugba

    2013-01-01

    In this study, it was aimed to investigate possible mobbing problems in universities, their causes and results, and to attract attention to precautions that can be taken. Phenomenology as one of the qualitative research methods was used in the study. Sample group of the study was selected through the criteria sampling method and eight instructors…

  3. Precipitation pathways for ferrihydrite formation in acidic solutions

    DOE PAGES

    Zhu, Mengqiang; Khalid, Syed; Frandsen, Cathrine; Wallace, Adam F.; Legg, Benjamin; Zhang, Hengzhong; Morup, Steen; Banfield, Jillian F.; Waychunas, Glenn A.

    2015-10-03

    In this study, iron oxides and oxyhydroxides form via Fe3+ hydrolysis and polymerization in many aqueous environments, but the pathway from Fe3+ monomers to oligomers and then to solid phase nuclei is unknown. In this work, using combined X-ray, UV–vis, and Mössbauer spectroscopic approaches, we were able to identify and quantify the long-time sought ferric speciation over time during ferric oxyhydroxide formation in partially-neutralized ferric nitrate solutions ([Fe3+] = 0.2 M, 1.8 < pH < 3). Results demonstrate that Fe exists mainly as Fe(H2O)63+, μ-oxo aquo dimers and ferrihydrite, and that with time, the μ-oxo dimer decreases while the othermore » two species increase in their concentrations. No larger Fe oligomers were detected. Given that the structure of the μ-oxo dimer is incompatible with those of all Fe oxides and oxyhydroxides, our results suggest that reconfiguration of the μ-oxo dimer structure occurs prior to further condensation leading up to the nucleation of ferrihydrite. The structural reconfiguration is likely the rate-limiting step involved in the nucleation process.« less

  4. Precipitation pathways for ferrihydrite formation in acidic solutions

    SciTech Connect

    Zhu, Mengqiang; Khalid, Syed; Frandsen, Cathrine; Wallace, Adam F.; Legg, Benjamin; Zhang, Hengzhong; Morup, Steen; Banfield, Jillian F.; Waychunas, Glenn A.

    2015-10-03

    In this study, iron oxides and oxyhydroxides form via Fe3+ hydrolysis and polymerization in many aqueous environments, but the pathway from Fe3+ monomers to oligomers and then to solid phase nuclei is unknown. In this work, using combined X-ray, UV–vis, and Mössbauer spectroscopic approaches, we were able to identify and quantify the long-time sought ferric speciation over time during ferric oxyhydroxide formation in partially-neutralized ferric nitrate solutions ([Fe3+] = 0.2 M, 1.8 < pH < 3). Results demonstrate that Fe exists mainly as Fe(H2O)63+, μ-oxo aquo dimers and ferrihydrite, and that with time, the μ-oxo dimer decreases while the other two species increase in their concentrations. No larger Fe oligomers were detected. Given that the structure of the μ-oxo dimer is incompatible with those of all Fe oxides and oxyhydroxides, our results suggest that reconfiguration of the μ-oxo dimer structure occurs prior to further condensation leading up to the nucleation of ferrihydrite. The structural reconfiguration is likely the rate-limiting step involved in the nucleation process.

  5. Precipitation pathways for ferrihydrite formation in acidic solutions

    NASA Astrophysics Data System (ADS)

    Zhu, Mengqiang; Frandsen, Cathrine; Wallace, Adam F.; Legg, Benjamin; Khalid, Syed; Zhang, Hengzhong; Mørup, Steen; Banfield, Jillian F.; Waychunas, Glenn A.

    2016-01-01

    Iron oxides and oxyhydroxides form via Fe3+ hydrolysis and polymerization in many aqueous environments, but the pathway from Fe3+ monomers to oligomers and then to solid phase nuclei is unknown. In this work, using combined X-ray, UV-vis, and Mössbauer spectroscopic approaches, we were able to identify and quantify the long-time sought ferric speciation over time during ferric oxyhydroxide formation in partially-neutralized ferric nitrate solutions ([Fe3+] = 0.2 M, 1.8 < pH < 3). Results demonstrate that Fe exists mainly as Fe(H2O)63+, μ-oxo aquo dimers and ferrihydrite, and that with time, the μ-oxo dimer decreases while the other two species increase in their concentrations. No larger Fe oligomers were detected. Given that the structure of the μ-oxo dimer is incompatible with those of all Fe oxides and oxyhydroxides, our results suggest that reconfiguration of the μ-oxo dimer structure occurs prior to further condensation leading up to the nucleation of ferrihydrite. The structural reconfiguration is likely the rate-limiting step involved in the nucleation process.

  6. Results from the long-term interaction and modeling of SRL-131 glass with aqueous solutions

    SciTech Connect

    Strachan, D.M.; Pederson, L.R.; Lokken, R.O.

    1985-11-01

    Leaching studies on SRL-131 simulated defense waste glass have been carried out for a duration of two years. This glass contained nonradioactive elements and depleted uranium to simulate the waste content. The leachants used in this study were deionized water, a sodium bicarbonate/silicic acid solution (silicate water), a synthetic groundwater, and a high ionic strength K-Mg-Na-Cl brine. Two temperatures were used: 40/sup 0/C and 90/sup 0/C. The long-term results were in fair agreement with modeling calculations performed using the PHREEQE geochemical code. The leachability of SRL-131 glass from results up to two years followed the trend: deionized water > silicate water > synthetic groundwater > salt brine at 40/sup 0/C and deionized water approx. = synthetic groundwater > silicate water > salt brine at 90/sup 0/C. Solid state analyses are reported along with an Appendix containing a complete data set.

  7. Electrical resistance response of polyaniline films to water, ethanol, and nitric acid solution

    NASA Astrophysics Data System (ADS)

    Yin, Hong-Xing; Li, Meng-Meng; Yang, H.; Long, Yun-Ze; Sun, Xin

    2010-08-01

    This paper reports on electrical resistance vs. aging time for the response of polyaniline films under exposure to water, ethanol and nitric acid (HNO3) solution. Camphor sulfonic acid-doped polyaniline films were prepared by a “doping-dedoping-redoping" method, the morphology and microstructures of the films were characterized by a scanning electron microscope and an x-ray diffractometer, the electrical resistance was measured by a four-probe method. It was found that a lower amount of water molecules infiltrating the film can decrease the film's resistance possibly due to an enhancement of charge carrier transfer between polyaniline chains, whereas excessive water molecules can swell inter-chain distances and result in a quick increase of resistance. The resistance of the film under exposure to ethanol increases and becomes much larger than the original value. However, HNO3 solution can decrease the film's resistance sharply possibly owing to doping effect of protonic acid. These results can help to understand the conduction mechanism in polyaniline films, and also indicate that the films have potential application in chemical sensors.

  8. Differential Effects of Permeating and Nonpermeating Solutes on the Fatty Acid Composition of Pseudomonas putida†

    PubMed Central

    Halverson, Larry J.; Firestone, Mary K.

    2000-01-01

    We examined the effect of reduced water availability on the fatty acid composition of Pseudomonas putida strain mt-2 grown in a defined medium in which the water potential was lowered with the permeating solutes NaCl or polyethylene glycol (PEG) with a molecular weight of 200 (PEG 200) or the nonpermeating solute PEG 8000. Transmission electron microscopy showed that −1.0-MPa PEG 8000-treated cells had convoluted outer membranes, whereas −1.0-MPa NaCl-treated or control cells did not. At the range of water potential (−0.25 to −1.5 MPa) that we examined, reduced water availability imposed by PEG 8000, but not by NaCl or PEG 200, significantly altered the amounts of trans and cis isomers of monounsaturated fatty acids that were present in whole-cell fatty acid extracts. Cells grown in basal medium or under the −0.25-MPa water potential imposed by NaCl or PEG 200 had a higher trans:cis ratio than −0.25-MPa PEG 8000-treated cells. As the water potential was lowered further with PEG 8000 amendments, there was an increase in the amount of trans isomers, resulting in a higher trans:cis ratio. Similar results were observed in cells grown physically separated from PEG 8000, indicating that these changes were not due to PEG toxicity. When cells grown in −1.5-MPa PEG 8000 amendments were exposed to a rapid water potential increase of 1.5 MPa or to a thermodynamically equivalent concentration of the permeating solute, NaCl, there was a decrease in the amount of trans fatty acids with a corresponding increase in the cis isomer. The decrease in the trans/cis ratio following hypoosomotic shock did not occur in the presence of the lipid synthesis inhibitor cerulenin or the growth inhibitors chloramphenicol and rifampicin, which indicates a constitutively operating enzyme system. These results indicate that thermodynamically equivalent concentrations of permeating and nonpermeating solutes have unique effects on membrane fatty acid composition. PMID:10831419

  9. Removal of radium from acidic solutions containing same by adsorption on coal fly ash

    DOEpatents

    Scheitlin, Frank M.

    1984-01-01

    The invention is a process for the removal of radium from acidic aqueous solutions. In one aspect, the invention is a process for removing radium from an inorganic-acid solution. The process comprises contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple, comparatively inexpensive, and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities throughout the United States. The invention is applicable, for example, to the recovery of .sup.226 Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings.

  10. Process for the removal of radium from acidic solutions containing same

    DOEpatents

    Scheitlin, F.M.

    The invention is a process for the removal of radium from acidic aqueous solutions. In one aspect, the invention is a process for removing radium from an inorganic-acid solution. The process comprises contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple, comparatively inexpensive, and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities throughout the United States. The invention is applicable, for example, to the recovery of /sup 226/Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings.

  11. Corrosion Inhibition of Carbon Steel by New Thiophene Azo Dye Derivatives in Acidic Solution

    NASA Astrophysics Data System (ADS)

    El-Haddad, Mahmoud N.; Fouda, A. S.; Mostafa, H. A.

    2013-08-01

    Inhibition of carbon steel corrosion in 2 M hydrochloric acid (HCl) solution by thiophene azo dye derivatives were studied using weight loss, electrochemical frequency modulation (EFM), and atomic absorption techniques. The experimental data suggest that the inhibition efficiency increases with increasing inhibitors concentration in presence of 103 μM potassium iodide (KI). This is due to synergistic effect. Thus, the experimental results suggested that the presence of these anions in the solution stabilized the adsorption of inhibitors molecules on the metal surface and improved the inhibition efficiency. The results of EFM experiments are a spectrum of current response as a function of frequency. The corrosion rate and Tafel parameters can be obtained with measurement by analyzing the harmonic frequencies. The adsorption of the inhibitors on metal surface obeys the Langmuir adsorption isotherm. The surface of metal examined using Fourier transform infrared and ultraviolet spectroscopy. Quantum chemical calculations were carried out and relations between computed parameters and experimental inhibition efficiency were discussed.

  12. Leaching of lead from zinc leach residue in acidic calcium chloride aqueous solution

    NASA Astrophysics Data System (ADS)

    Wang, Le; Mu, Wen-ning; Shen, Hong-tao; Liu, Shao-ming; Zhai, Yu-chun

    2015-05-01

    A process with potentially reduced environmental impacts and occupational hazards of lead-bearing zinc plant residue was studied to achieve a higher recovery of lead via a cost-effective and environmentally friendly process. This paper describes an optimization study on the leaching of lead from zinc leach residue using acidic calcium chloride aqueous solution. Six main process conditions, i.e., the solution pH value, stirring rate, concentration of CaCl2 aqueous solution, liquid-to-solid (L/S) ratio, leaching temperature, and leaching time, were investigated. The microstructure and components of the residue and tailing were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). On the basis of experimental results, the optimum reaction conditions were determined to be a solution pH value of 1, a stirring rate of 500 r·min-1, a CaCl2 aqueous solution concentration of 400 g·L-1, a liquid-to-solid mass ratio of 7:1, a leaching temperature of 80°C, and a leaching time of 45 min. The leaching rate of lead under these conditions reached 93.79%, with an iron dissolution rate of 19.28%. Silica did not take part in the chemical reaction during the leaching process and was accumulated in the residue.

  13. Influence of solution volume on the dissolution rate of silicon dioxide in hydrofluoric acid.

    PubMed

    Shvartsev, Boris; Gelman, Danny; Komissarov, Ilia; Epshtein, Alon; Starosvetsky, David; Ein-Eli, Yair

    2015-02-01

    Experimental data and modeling of the dissolution of various Si/SiO2 thermal coatings in different volumes of hydrofluoric acid (HF) are reported. The rates of SiO2 -film dissolution, measured by means of various electrochemical techniques, and alteration in HF activity depend on the thickness of the film coating. Despite the small volumes (0.6-1.2 mL) of the HF solution, an effect of SiO2 -coating thickness on the dissolution rate was detected. To explain alterations detected in HF activity after SiO2 dissolution, spectroscopic analyses (NMR and FTIR) of the chemical composition of the solutions were conducted. This is associated with a modification in the chemical composition of the HF solution, which results in either the formation of an oxidized species in solution or the precipitation of dissolution products. HF2 (-) accumulation in the HF solution, owing to SiO2 dissolution was identified as the source of the chemical alteration.

  14. Evaluation of poly (aspartic acid sodium salt) as a draw solute for forward osmosis.

    PubMed

    Gwak, Gimun; Jung, Bokyung; Han, Sungsoo; Hong, Seungkwan

    2015-09-01

    Poly (aspartic acid sodium salt) (PAspNa) was evaluated for its potential as a novel draw solute in forward osmosis (FO). The inherent advantages of PAspNa, such as good water solubility, high osmotic pressure, and nontoxicity, were first examined through a series of physicochemical analyses and atomic-scale molecular dynamics simulations. Then, lab-scale FO tests were performed to evaluate its suitability in practical processes. Compared to other conventional inorganic solutes, PAspNa showed comparable water flux but significantly lower reverse solute flux, demonstrating its suitability as a draw solute. Moreover, fouling experiments using synthetic wastewater as a feed solution demonstrated that PAspNa reversely flowed to the feed side reduced inorganic scaling on the membrane active layer. The recyclability of PAspNa was studied using both nanofiltration (NF) and membrane distillation (MD) processes, and the results exhibited its ease of recovery. This research reported the feasibility and applicability of FO-NF or FO-MD processes using PAspNa for wastewater reclamation and brackish water desalination. PMID:26005789

  15. Evaluation of poly (aspartic acid sodium salt) as a draw solute for forward osmosis.

    PubMed

    Gwak, Gimun; Jung, Bokyung; Han, Sungsoo; Hong, Seungkwan

    2015-09-01

    Poly (aspartic acid sodium salt) (PAspNa) was evaluated for its potential as a novel draw solute in forward osmosis (FO). The inherent advantages of PAspNa, such as good water solubility, high osmotic pressure, and nontoxicity, were first examined through a series of physicochemical analyses and atomic-scale molecular dynamics simulations. Then, lab-scale FO tests were performed to evaluate its suitability in practical processes. Compared to other conventional inorganic solutes, PAspNa showed comparable water flux but significantly lower reverse solute flux, demonstrating its suitability as a draw solute. Moreover, fouling experiments using synthetic wastewater as a feed solution demonstrated that PAspNa reversely flowed to the feed side reduced inorganic scaling on the membrane active layer. The recyclability of PAspNa was studied using both nanofiltration (NF) and membrane distillation (MD) processes, and the results exhibited its ease of recovery. This research reported the feasibility and applicability of FO-NF or FO-MD processes using PAspNa for wastewater reclamation and brackish water desalination.

  16. Chemisorption of Perfluorooctanoic Acid on Powdered Activated Carbon Initiated by Persulfate in Aqueous Solution.

    PubMed

    Sun, Bo; Ma, Jun; Sedlak, David L

    2016-07-19

    Perfluorooctanoic acid (PFOA) is a perfluorocarboxylic acid that is difficult to treat by most conventional methods. As a result, it is often removed from solution by adsorption on powdered activated carbon (PAC), followed by incineration of the spent carbon. To provide a new approach for treatment, PFOA was exposed to sulfate radicals (SO4(-•)) produced by thermolysis of persulfate (S2O8(2-)) in the presence of PAC. Under acidic conditions, thermal activation of persulfate resulted in transformation of PFOA to shorter-chain-length perfluorinated compounds, as previously reported. However, when thermolysis of persulfate occurred under circumneutral pH conditions in the presence of PAC, a new removal pathway for PFOA was observed. Under these conditions, the removal of PFOA was attributable to chemisorption, a process in which PAC catalyzed persulfate decomposition and reacted with the transformation products to produce covalently bound PFOA. At PAC concentrations between 200 and 1000 mg/L and an initial PFOA concentration of 0.5 μM, covalent bonding resulted in removal of 10-40% of the PFOA. Under these conditions, the process resulted in removal of more than half of a more hydrophilic perfluoroalkyl acid (i.e., perfluorobutanoic acid, PFBA), which was greater than the amount of PFBA removed by physical adsorption on PAC. Although the high reaction temperatures (i.e., 80 °C) and relatively high doses of PAC used in this study may be impractical for drinking water treatment, this process may be applied to the treatment of these recalcitrant compounds in industrial wastewater, reverse osmosis concentrate, and other waters that contain high concentrations of PFOA and other perfluorocarboxylic acids. PMID:27336204

  17. Growth of various Au Ag nanocomposites from gold seeds in amino acid solutions

    NASA Astrophysics Data System (ADS)

    Huang, Yu-Fen; Lin, Yang-Wei; Chang, Huan-Tsung

    2006-10-01

    In this paper, we describe an easy procedure for the preparation of differently shaped and sized Au-Ag nanocomposites from gold nanorod (AuNR) seeds in various amino acid solutions—arginine (Arg), cysteine (Cys), glycine (Gly), glutamate (Glu), glutamine (Gln), histidine (His), lysine (Lys), and methionine (Met), respectively—at values of pH ranging from 8.0 to 11.5. Our results suggest that the pH, the nature of the amino acid, and its concentration all have significant impact on the preparation of Au-Ag nanocomposites; these factors exhibit their effects mainly through control over the reducing ability of ascorbate and/or its recognition capability, as well as through control over the surface charges of the amino acids on the AuNRs. Depending on the value of pH, we were able to prepare I-shaped, dumbbell-shaped, and/or sphere-shaped Au-Ag nanocomposites in 0.1 M solutions of Arg, Gly, Glu, Gln, Lys, and Met. In His solutions at pH 8.0 and 9.0, we obtained peanut-shaped Au-Ag nanocomposites. Corn-shaped Au-Ag nanocomposites were prepared in 0.1 M Met solutions (pH 9.0 and 10.0). By controlling the Lys concentration at pH 10.0, we synthesized pearl-necklace-shaped Au-Ag nanoparticles and Au-Ag wires. Based on the TEM images, we conclude that this simple and reproducible synthetic approach allows preparation of high-quality (>87%, beside>77% in His solutions) Au-Ag nanocomposites with various shapes and sizes under different conditions.

  18. Separation of ions in acidic solution by capillary electrophoresis

    SciTech Connect

    Thornton, M.

    1997-10-08

    Capillary electrophoresis (CE) is an effective method for separating ionic species according to differences in their electrophoretic mobilities. CE separations of amino acids by direct detection are difficult due to their similar electrophoretic mobilities and low absorbances. However, native amino acids can be separated by CE as cations at a low pH by adding an alkanesulfonic acid to the electrolyte carrier which imparts selectivity to the system. Derivatization is unnecessary when direct UV detection is used at 185 nm. Simultaneous speciation of metal cations such as vanadium (IV) and vanadium (V) can easily be performed without complexation prior to analysis. An indirect UV detection scheme for acidic conditions was also developed using guanidine as the background carrier electrolyte (BCE) for the indirect detection of metal cations. Three chapters have been removed for separate processing. This report contains introductory material, references, and general conclusions. 80 refs.

  19. Dynamic dielectric properties of some carboxylic acid esters in benzene solution

    NASA Astrophysics Data System (ADS)

    Ghoneim, Ahmed M.; Stockhause, Martina; Becker, U.; Biedenkap, R.; Elsebrock, R.

    1997-06-01

    The dielectric absorption spectrum between some MHz and 36 GHz has been measured at 20 degrees C for S(-)-lactic acid methylester, succinic acid dimethylester, L(-)- malic acid dimethylester and L(+)-tartaric acid diethylester, over the whole concentration range of benzene solutions of these substances. The loss function can be described by up to four Debye type spectral components. The relaxation parameters are reported and discussed in particular with respect to association effects.

  20. New insights into structural alteration of enamel apatite induced by citric acid and sodium fluoride solutions.

    PubMed

    Wang, Xiaojie; Klocke, Arndt; Mihailova, Boriana; Tosheva, Lubomira; Bismayer, Ulrich

    2008-07-24

    Attenuated total reflectance infrared spectroscopy and complementary scanning electron microscopy were applied to analyze the surface structure of enamel apatite exposed to citric acid and to investigate the protective potential of fluorine-containing reagents against citric acid-induced erosion. Enamel and, for comparison, geological hydroxylapatite samples were treated with aqueous solutions of citric acid and sodium fluoride of different concentrations, ranging from 0.01 to 0.5 mol/L for citric acid solutions and from 0.5 to 2.0% for fluoride solutions. The two solutions were applied either simultaneously or consecutively. The citric acid-induced structural modification of apatite increases with the increase in the citric acid concentration and the number of treatments. The application of sodium fluoride alone does not suppress the atomic level changes in apatite exposed to acidic agents. The addition of sodium fluoride to citric acid solutions leads to formation of surface CaF2 and considerably reduces the changes in the apatite P-O-Ca framework. However, the CaF2 globules deposited on the enamel surface seem to be insufficient to prevent the alteration of the apatite structure upon further exposure to acidic agents. No evidence for fluorine-induced recovery of the apatite structure was found.

  1. PROCESS OF SECURING PLUTONIUM IN NITRIC ACID SOLUTIONS IN ITS TRIVALENT OXIDATION STATE

    DOEpatents

    Thomas, J.R.

    1958-08-26

    >Various processes for the recovery of plutonium require that the plutonium be obtalned and maintained in the reduced or trivalent state in solution. Ferrous ions are commonly used as the reducing agent for this purpose, but it is difficult to maintain the plutonium in a reduced state in nitric acid solutions due to the oxidizing effects of the acid. It has been found that the addition of a stabilizing or holding reductant to such solution prevents reoxidation of the plutonium. Sulfamate ions have been found to be ideally suitable as such a stabilizer even in the presence of nitric acid.

  2. Reprocessing system with nuclide separation based on chromatography in hydrochloric acid solution

    SciTech Connect

    Suzuki, Tatsuya; Tachibana, Yu; Koyama, Shi-ichi

    2013-07-01

    We have proposed the reprocessing system with nuclide separation processes based on the chromatographic technique in the hydrochloric acid solution system. Our proposed system consists of the dissolution process, the reprocessing process, the minor actinide separation process, and nuclide separation processes. In the reprocessing and separation processes, the pyridine resin is used as a main separation media. It was confirmed that the dissolution in the hydrochloric acid solution is easily achieved by the plasma voloxidation and by the addition of oxygen peroxide into the hydrochloric acid solution.

  3. Transitions to asexuality result in excess amino acid substitutions.

    PubMed

    Paland, Susanne; Lynch, Michael

    2006-02-17

    Theory predicts that linkage between genetic loci reduces the efficiency of purifying selection. Because of the permanent linkage of all heritable genetic material, asexual lineages may be exceptionally prone to deleterious-mutation accumulation in both nuclear and organelle genes. Here, we show that the ratio of the rate of amino acid to silent substitution (Ka/Ks) in mitochondrial protein-coding genes is higher in obligately asexual lineages than in sexual lineages of the microcrustacean Daphnia pulex. Using a phylogeny-based approach to quantify the frequency of mutational-effect classes, we estimate that mitochondrial protein-coding genes in asexual lineages accumulate deleterious amino acid substitutions at four times the rate in sexual lineages. These results support the hypothesis that sexual reproduction plays a prominent role in reducing the mutational burden in populations.

  4. Biosorption of methyl blue onto tartaric acid modified wheat bran from aqueous solution

    PubMed Central

    2012-01-01

    Tartaric acid modified wheat bran was utilized as adsorbent to remove methyl blue, a basic dye from aqueous solution. Batch experiments were carried out to study the effect of various experimental parameters such as initial solution pH, contact time, initial dye concentration and adsorbent dosage, on dye adsorption. The results showed that the modification of wheat bran by tartaric acid significantly improved its adsorption capacity, and made this material a suitable adsorbent to remove methyl blue. The adsorption capacity of modified wheat bran was about 1.6 times higher than that of unmodified one. The amount of methyl blue adsorbed was found to vary with initial solution pH, adsorbent dosage, contact time and initial methyl blue concentration. Kinetics study showed that the overall adsorption rate of methyl blue was illustrated by pseudo-second-order kinetic model. The applicability of the Langmuir and Freundlich models for the data was tested. Both models adequately described the experimental data of the biosorption of methyl blue. The maximum adsorption capacity for methyl blue calculated from Langmuir model was 25.18 mg/g. The study has shown the effectiveness of modified wheat bran in the removal of methyl blue, and that it can be considered as an attractive alternative to the more expensive technologies used in wastewater treatment. PMID:23369295

  5. Structural and transport properties of Nafion in hydrobromic-acid solutions

    SciTech Connect

    Kusoglu, A; Cho, KT; Prato, RA; Weber, AZ

    2013-12-01

    Proton-exchange membranes are key solid-state ion carriers in many relevant energy technologies including flow batteries, fuel cells, and solar-fuel generators. In many of these systems, the membranes are in contact with electrolyte solutions. In this paper, we focus on the impact of different HBr, a flow-battery and exemplary acid electrolyte, external concentrations on the conductivity of Nafion, a perfluorosulfonic acid membrane that is commonly used in many energy-related applications. The peak and then decrease in conductivity is correlated with measured changes in the water and HBr content within the membrane. In addition, small-angle x-ray scattering is used to probe the nanostructure to correlate how the interactions of the bromide ion with the fixed sulfonic-acid sites impact conductivity and hydrophilic domain distance. It is also shown that membrane pretreatment has a large impact on the underlying structure/function relationship. The obtained data and results are useful for delineation of optimal operating regimes for flow batteries and similar technologies as well as in understanding underlying structure/function relationships of ionomers in electrolyte solutions. (C) 2013 Elsevier B.V. All rights reserved.

  6. Photophysics of Fe(III) complexes with fluorosalicylic acid isomers in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Pozdnyakov, Ivan P.; Melnikov, Alexey A.; Šípoš, Rastislav; Chekalin, Sergey V.; Šima, Jozef

    2016-09-01

    Transient absorption spectroscopy is used to study photophysical processes of 1:1 Fe(III) complexes with all four fluorosalicylic acid isomers (Fe-FSAs) in aqueous solutions. Excited states of Fe-FSAs decay to the ground electronic state with two time constants. The faster process is interpreted as internal conversion to the vibrationally hot electronic ground state and the slower one - as a combination of vibrational cooling and solvation of the ground state. The results obtained for Fe-FSAs and other previously investigated Fe(III) salicylato compounds allow us to reveal the main cause of photochemical stability of the complexes upon charge transfer band excitation.

  7. Complexation of U(VI) with 1-Hydroxyethane-1,1-diphosphonicAcid (HEDPA) in Acidic to Basic Solutions

    SciTech Connect

    Reed, W A; Rao, L; Zanonato, P; Garnov, A; Powell, B A; Nash, K L

    2007-01-24

    Complexation of U(VI) with 1-hydroxyethane-1,1-diphosphonic acid (HEDPA) in acidic to basic solutions has been studied with multiple techniques. A number of 1:1 (UO{sub 2}H{sub 3}L), 1:2 (UO{sub 2}H{sub j}L{sub 2} where j = 4, 3, 2, 1, 0 and -1) and 2:2 ((UO{sub 2}){sub 2}H{sub j}L{sub 2} where j = 1, 0 and -1) complexes form, but the 1:2 complexes are the major species in a wide pH range. Thermodynamic parameters (formation constants, enthalpy and entropy of complexation) were determined by potentiometry and calorimetry. Data indicate that the complexation of U(VI) with HEDPA is exothermic, favored by the enthalpy of complexation. This is in contrast to the complexation of U(VI) with dicarboxylic acids in which the enthalpy term usually is unfavorable. Results from electrospray ionization mass spectrometry (ESI-MS) and {sup 31}P NMR have confirmed the presence of 1:1, 1:2 and 2:2 U(VI)-HEDPA complexes.

  8. Nucleic Acids Bind to Nanoparticulate iron (II) Monosulphide in Aqueous Solutions

    NASA Astrophysics Data System (ADS)

    Hatton, Bryan; Rickard, David

    2008-06-01

    In the hydrothermal FeS-world origin of life scenarios nucleic acids are suggested to bind to iron (II) monosulphide precipitated from the reaction between hydrothermal sulphidic vent solutions and iron-bearing oceanic water. In lower temperature systems, the first precipitate from this process is nanoparticulate, metastable FeSm with a mackinawite structure. Although the interactions between bulk crystalline iron sulphide minerals and nucleic acids have been reported, their reaction with nanoparticulate FeSm has not previously been investigated. We investigated the binding of different nucleic acids, and their constituents, to freshly precipitated, nanoparticulate FeSm. The degree to which the organic molecules interacted with FeSm is chromosomal DNA > RNA > oligomeric DNA > deoxadenosine monophosphate ≈ deoxyadenosine ≈ adenine. Although we found that FeSm does not fluoresce within the visible spectrum and there is no quantum confinement effect seen in the absorption, the mechanism of linkage of the FeSm to these biomolecules appears to be primarily electrostatic and similar to that found for the attachment of ZnS quantum dots. The results of a preliminary study of similar reactions with nanoparticulate CuS further supported the suggestion that the interaction mechanism was generic for nanoparticulate transition metal sulphides. In terms of the FeS-world hypothesis, the results of this study further support the idea that sulphide minerals precipitated at hydrothermal vents interact with biomolecules and could have assisted in the formation and polymerisation of nucleic acids.

  9. Theoretical insights into the properties of amino acid ionic liquids in aqueous solution.

    PubMed

    Zhu, Xueying; Ai, Hongqi

    2016-07-01

    This report presents a systematic investigation of the interactions of water molecule(s) with a series of amino acid cations (Gly(+), Ala(+), Val(+), and Leu(+)), halogen anions (Cl(-), Br(-), BF4 (-), and PF6 (-)), and clusters (GlyCl) n (n = 1-5). The results reveal that H-bonds between amino acid ionic liquids (AAILs) and water molecules are crucial to the properties of aqueous solution of AAILs. The properties of AAIL in water solution depend on the alkyl chain of the amino acid cation, the size of the halogen anion, and the number of water molecules, which provides a certain theoretical basis for the design and application of new AAILs. A series of calculations for some different models showed that quadruple-GlyCl hydrate represents a basic unit for the Gly-water binary system, and can be employed as the simplest model for studying an AAIL-water cluster. On the basis of this model, the effects of water on the hygroscopicity, speed of solubility, viscosity, density, solution enthalpy, and polarity of the AAIL were also predicted. Most importantly, unlike traditional ILs, the novel GlyCl-type AAIL favors interaction of its cationic part, rather than its anionic part, with surrounding water molecules, thus amino acid cationic ILs expand the types of IL available, increasing the choice of ILs for different purposes. We hope that the application of this AAIL in many fields will lead to optimization of this class of compound and be of benefit to the environment. Graphical Abstract Quadruple-GlyCl hydrate represents the basic unit for a GlyCl-water binary system, which can be employed as the simplest model for studying an amino acid ionic liquid (AAIL)-water cluster. The effects of available water on some properties of AAIL are predicted. GlyCl-type AAIL is a novel IL, which prefers its cationic part over its anionic part for interaction with surrounding water molecules. The properties of AAIL in water solution can be adjusted by varying the ion used and the

  10. Theoretical insights into the properties of amino acid ionic liquids in aqueous solution.

    PubMed

    Zhu, Xueying; Ai, Hongqi

    2016-07-01

    This report presents a systematic investigation of the interactions of water molecule(s) with a series of amino acid cations (Gly(+), Ala(+), Val(+), and Leu(+)), halogen anions (Cl(-), Br(-), BF4 (-), and PF6 (-)), and clusters (GlyCl) n (n = 1-5). The results reveal that H-bonds between amino acid ionic liquids (AAILs) and water molecules are crucial to the properties of aqueous solution of AAILs. The properties of AAIL in water solution depend on the alkyl chain of the amino acid cation, the size of the halogen anion, and the number of water molecules, which provides a certain theoretical basis for the design and application of new AAILs. A series of calculations for some different models showed that quadruple-GlyCl hydrate represents a basic unit for the Gly-water binary system, and can be employed as the simplest model for studying an AAIL-water cluster. On the basis of this model, the effects of water on the hygroscopicity, speed of solubility, viscosity, density, solution enthalpy, and polarity of the AAIL were also predicted. Most importantly, unlike traditional ILs, the novel GlyCl-type AAIL favors interaction of its cationic part, rather than its anionic part, with surrounding water molecules, thus amino acid cationic ILs expand the types of IL available, increasing the choice of ILs for different purposes. We hope that the application of this AAIL in many fields will lead to optimization of this class of compound and be of benefit to the environment. Graphical Abstract Quadruple-GlyCl hydrate represents the basic unit for a GlyCl-water binary system, which can be employed as the simplest model for studying an amino acid ionic liquid (AAIL)-water cluster. The effects of available water on some properties of AAIL are predicted. GlyCl-type AAIL is a novel IL, which prefers its cationic part over its anionic part for interaction with surrounding water molecules. The properties of AAIL in water solution can be adjusted by varying the ion used and the

  11. Magnesium hydroxide as the neutralizing agent for radioactive hydrochloric acid solutions

    SciTech Connect

    Palmer, M.J.; Fife, K.W.

    1995-10-01

    The current technology at Los Alamos for removing actinides from acidic chloride waste streams is precipitation with approximately 10 M potassium hydroxide. Although successful, there are many inherent drawbacks to this precipitation technique which will be detailed in this paper. Magnesium hydroxide (K{sub sp} = 1.3 x 10{sup -11}) has limited solubility in water and as a result of the common ion effect, cannot generate a filtrate with a pH greater than 9. At a pH of 9, calcium (K{sub sp} = 5.5 x 10{sup -6}) will not coprecipitate as the hydroxide. This is an important factor since many acidic chloride feeds to hydroxide precipitation contain significant amounts of calcium. In addition, neutralization with Mg(OH){sub 2} produces a more filterable precipitate because neutralization occurs as the Mg(OH){sub 2} is dissolved by the acid rather than as a result of the much faster liquid/liquid reaction of KOH with the waste acid. This slower solid/liquid reaction allows time for crystal growth to occur and produces more easily filterable precipitates. On the other hand, neutralization of spent acid with strong KOH that yields numerous hydroxide ions in solution almost instantaneously forming a much larger volume of small crystallites that result in gelatinous, slow-filtering precipitates. Magnesium hydroxide also offers a safety advantage. Although mildly irritating, it is a weak base and safe and easy to handle. From a waste minimization perspective, Mg(OH){sub 2} offers many advantages. First, the magnesium hydroxide is added as a solid. This step eliminates the diluent water used in KOH neutralizations. Secondly, because the particle size of the precipitate is larger, more actinides are caught on the filter paper resulting in a smaller amount of actinide being transferred to the TA-50 Liquid Waste Treatment Facility. Third, the amount of solids that must be reprocessed is significantly smaller resulting in less waste generation from the downstream processes.

  12. Effect of acidic solutions on the surface degradation of a micro-hybrid composite resin.

    PubMed

    Münchow, Eliseu A; Ferreira, Ana Cláudia A; Machado, Raissa M M; Ramos, Tatiana S; Rodrigues-Junior, Sinval A; Zanchi, Cesar H

    2014-01-01

    Composite resins may undergo wear by the action of chemical substances (e.g., saliva, alcohol, bacterial acids) of the oral environment, which may affect the material's structure and surface properties. This study evaluated the effect of acidic substances on the surface properties of a micro-hybrid composite resin (Filtek Z-250). Eighty specimens were prepared, and baseline hardness and surface roughness (KMN0 and Ra0, respectively) were measured. The specimens were subjected to sorption (SO) and solubility (SL) tests according to ISO 4049:2009, but using different storage solutions: deionized water; 75/25 vol% ethanol/water solution; lactic acid; propionic acid; and acetic acid. The acids were used in two concentrations: PA and 0.02 N. pH was measured for all solutions and final hardness (KMN1) and surface roughness (Ra1) were measured. Data were analyzed with paired t-tests and one-way ANOVA and Tukey's test (a=5%). All solutions decreased hardness and increased the Ra values, except for the specimens stored in water and 0.02 N lactic acid, which maintained the hardness. All solutions produced similar SO and SL phenomena, except for the 0.02 N lactic acid, which caused lower solubility than the other solutions. Ethanol showed the highest pH (6.6) and the 0.02 N lactic acid the lowest one (2.5). The solutions affected negatively the surface properties of the composite resin; in addition, an acidic pH did not seem to be a significant factor that intensifies the surface degradation phenomena. PMID:25250496

  13. Fixed bed adsorption of 2-naphthalenesulfonic acid from aqueous solution by composite resin.

    PubMed

    Jia, Dong M; Li, Ya P; Li, Yue J; Li, Yong G; Li, Chang H

    2014-02-01

    Adsorption behavior of the iron impregnated, weakly basic resin D301 (Fe-D301) for removal of 2-naphthalenesulfonic acid (2-NSA) from aqueous solution was studied by using a fixed-bed column. The effects of process variables such as bed height, flow rate, and coexisting ions were investigated. The results indicated that the breakpoint and exhaustion point increased with increasing bed height and decreased with increasing 2-NSA flowrate. Experimental data showed a strong fit to the Bed Depth Service Time model. The coexisting ions in the 2-NSA solution had a clear effect on the breakthrough volume. The high extent of recovery of 2-NSA with good reproducibility provided an effective method for the separation of 2-NSA by the adsorbent Fe-D301.

  14. Glucose metabolic flux distribution of Lactobacillus amylophilus during lactic acid production using kitchen waste saccharified solution.

    PubMed

    Liu, Jianguo; Wang, Qunhui; Zou, Hui; Liu, Yingying; Wang, Juan; Gan, Kemin; Xiang, Juan

    2013-11-01

    The (13) C isotope tracer method was used to investigate the glucose metabolic flux distribution and regulation in Lactobacillus amylophilus to improve lactic acid production using kitchen waste saccharified solution (KWSS). The results demonstrate that L. amylophilus is a homofermentative bacterium. In synthetic medium, 60.6% of the glucose entered the Embden-Meyerhof-Parnas (EMP) to produce lactic acid, whereas 36.4% of the glucose entered the pentose phosphate metabolic pathway (HMP). After solid-liquid separation of the KWSS, the addition of Fe(3+) during fermentation enhanced the NADPH production efficiency and increased the NADH content. The flux to the EMP was also effectively increased. Compared with the control (60.6% flux to EMP without Fe(3+) addition), the flux to the EMP with the addition of Fe(3+) (74.3%) increased by 23.8%. In the subsequent pyruvate metabolism, Fe(3+) also increased lactate dehydrogenase activity, and inhibited alcohol dehydrogenase, pyruvate dehydrogenase and pyruvate carboxylase, thereby increasing the lactic acid production to 9.03 g l(-1) , an increase of 8% compared with the control. All other organic acid by-products were lower than in the control. However, the addition of Zn(2+) showed an opposite effect, decreasing the lactic acid production. In conclusion it is feasible and effective means using GC-MS, isotope experiment and MATLAB software to integrate research the metabolic flux distribution of lactic acid bacteria, and the results provide the theoretical foundation for similar metabolic flux distribution. PMID:23489617

  15. SULFURIC ACID REMOVAL PROCESS EVALUATION: SHORT-TERM RESULTS

    SciTech Connect

    Gary M. Blythe; Richard McMillan

    2002-03-04

    results of the short-term tests; the long-term test results will be reported in a later document. The short-term test results showed that three of the four reagents tested, dolomite powder, commercial magnesium hydroxide slurry, and byproduct magnesium hydroxide slurry, were able to achieve 90% or greater removal of sulfuric acid compared to baseline levels. The molar ratio of alkali to flue gas sulfuric acid content (under baseline conditions) required to achieve 90% sulfuric acid removal was lowest for the byproduct magnesium hydroxide slurry. However, this result may be confounded because this was the only one of the three slurries tested with injection near the top of the furnace across from the pendant superheater platens. Injection at the higher level was demonstrated to be advantageous for this reagent over injection lower in the furnace, where the other slurries were tested.

  16. SULFURIC ACID REMOVAL PROCESS EVALUATION: SHORT-TERM RESULTS

    SciTech Connect

    Gary M. Blythe; Richard McMillan

    2002-02-04

    the results of the short-term tests; the long-term test results will be reported in a later document. The short-term test results showed that three of the four reagents tested, dolomite powder, commercial magnesium hydroxide slurry, and byproduct magnesium hydroxide slurry, were able to achieve 90% or greater removal of sulfuric acid compared to baseline levels. The molar ratio of alkali to flue gas sulfuric acid content (under baseline conditions) required to achieve 90% sulfuric acid removal was lowest for the byproduct magnesium hydroxide slurry. However, this result may be confounded because this was the only one of the three slurries tested with injection near the top of the furnace across from the pendant superheater platens. Injection at the higher level was demonstrated to be advantageous for this reagent over injection lower in the furnace, where the other slurries were tested.

  17. Multiple-acid equilibria in adsorption of carboxylic acids from dilute aqueous solution

    SciTech Connect

    Husson, S.M.; King, C.J.

    1999-02-01

    Equilibria were measured for adsorption of carboxylic acids from aqueous, binary-acid mixtures of lactic and succinic acids and acetic and formic acids onto basic polymeric sorbents. The experimentally determined adsorption isotherms compared well with model predictions, confirming that simple extensions from adsorption of individual acids apply. Fixed-bed studies were carried out that establish the efficacy of chromatographic fractionation of lactic and succinic acids using basic polymeric sorbents. Finally, sequential thermal and solvent regeneration of lactic and acetic acid-laden sorbents was investigated as a method to fractionate among coadsorbed volatile and nonvolatile acids. Essentially complete removal of the acetic acid from the acid-laden sorbent was achieved by vaporization under the conditions used; a small amount of loss of lactic acid (about 11%) was observed.

  18. Effect of acidic solutions on the microhardness of dentin and set OrthoMTA and their cytotoxicity on murine macrophage

    PubMed Central

    Shon, Won-Jun; Lee, Woocheol

    2016-01-01

    Objectives To evaluate the effects of three acids on the microhardness of set mineral trioxide aggregate (MTA) and root dentin, and cytotoxicity on murine macrophage. Materials and Methods OrthoMTA (BioMTA) was mixed and packed into the human root dentin blocks of 1.5 mm diameter and 5 mm height. Four groups, each of ten roots, were exposed to 10% citric acid (CA), 5% glycolic acid (GA), 17% ethylenediaminetetraacetic acid (EDTA), and saline for five minutes after setting of the OrthoMTA. Vickers surface microhardness of set MTA and dentin was measured before and after exposure to solutions, and compared between groups using one-way ANOVA with Tukey test. The microhardness value of each group was analyzed using student t test. Acid-treated OrthoMTA and dentin was examined by scanning electron microscope (SEM). Cell viability of tested solutions was assessed using WST-8 assay and murine macrophage. Results Three test solutions reduced microhardness of dentin. 17% EDTA demonstrated severe dentinal erosion, significantly reduced the dentinal microhardness compared to 10% CA (p = 0.034) or 5% GA (p = 0.006). 10% CA or 5% GA significantly reduced the surface microhardness of set MTA compared to 17% EDTA and saline (p < 0.001). Acid-treated OrthoMTA demonstrated microporous structure with destruction of globular crystal. EDTA exhibited significantly more cellular toxicity than the other acidic solutions at diluted concentrations (0.2, 0.5, 1.0%). Conclusions Tested acidic solutions reduced microhardness of root dentin. Five minute's application of 10% CA and 5% GA significantly reduced the microhardness of set OrthoMTA with lower cellular cytotoxicity compared to 17% EDTA. PMID:26877986

  19. In vitro evaluation of the cytotoxic effects of acid solutions used as canal irrigants.

    PubMed

    Malheiros, C F; Marques, M M; Gavini, G

    2005-10-01

    Solutions of EDTA and citric acid have been used as canal irrigants. These substances must be compatible with apical periodontal tissue. The aim of this study was to evaluate comparatively the cytotoxicity of a 17% EDTA solution and that of three solutions with different concentrations of citric acid (10, 15, and 25%) on cultured fibroblasts. The solutions were diluted to 0.1% and 0.5% in culture medium and then applied to NIH 3T3 cells. After 0, 6, 12, and 24 h (short-term assay; viability) and 1, 3, 5, and 7 days (long-term assay; survival), the cells were counted. The data were compared by ANOVA. In the short-term experiments, all solutions presented a percentage of cell viability similar to that of control cells, except for the 17% EDTA solution diluted to 0.5%. After the long-term assay, all groups presented a continuous and progressive cell growth except for the 17% EDTA solution and for the 25% citric acid solution at a 0.5% dilution. The citric acid solution did not impair cell growth and viability, proving to be noncytotoxic in vitro.

  20. Standard addition method for free acid determination in solutions with hydrolyzable ions

    SciTech Connect

    Baumann, E.W.

    1981-01-01

    The free acid content of solutions containing hydrolyzable ions has been determined potentiometrically by a standard addition method. Two increments of acid are added to the sample in a 1M potassium thiocyanate solution. The sample concentration is calculated by solution of three simultaneous Nernst equations. The method has been demonstrated for solutions containing Al/sup 3 +/, Cr/sup 3 +/, Fe/sup 3 +/, Ni/sup 2 +/, Th/sup 4 +/, or UO/sub 2//sup 2 +/ with a metal-to-acid ratio of < 2.5. The method is suitable for determination of 10 ..mu..moles acid in 10 mL total volume. The accuracy is verifiable by reasonable agreement of the Nerst slopes found in the presence and absence of hydrolyzable ions. The relative standard deviation is < 2.5 percent.

  1. Thermodynamics of the complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Mudarisova, R. Kh.; Badykova, L. A.

    2016-03-01

    The thermodynamics of complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions is studied by means spectroscopy. The standard thermodynamic characteristics (Δ H°; Δ G°; Δ S°) of complexation are calculated.

  2. Radiation- and photo-induced formation of salicylic acid from phenol and CO{sub 2} in aqueous solution

    SciTech Connect

    Krapfenbauer, K.; Getoff, N.

    1996-12-31

    The concentration of CO{sub 2} in the atmosphere is steady increasing because of the combustion of fossil fuels and the industrial pollution. As a result, global warming has occurred. In the present study the formation of the salicylic acid and other products, originating from the carboxylation of phenol is investigated. It has been found that the formation of salicylic acid strongly depend on several experimental conditions: pH of the solution, concentration of phenol and CO{sub 2}, and absorbed dose. The formation of salicylic acid was also studied in the presence of catalysts. Photo-induced carboxylation of phenol to salicylic acid will be also reported. Probable reaction mechanisms for the salicylic acid formation are suggested. Finally, a comparison is made between the well known industrial Kolbe-Schmitt process for salicylic acid production and the aspects of the present new method for CO{sub 2} utilization.

  3. Investigation of the swelling behaviour of hydrogels in aqueous acid or alkaline solutions

    NASA Astrophysics Data System (ADS)

    Althans, Daniel; Enders, Sabine

    2014-09-01

    For development of tailor made drug delivery systems using poly(N-isopropylacrylamide) hydrogels, the influence of acids and bases added to the aqueous solution on the swelling behaviour as function of concentration, temperature and kind of acid or base were investigated experimentally. The selected acids are formic, acetic, propionic, lactic, succinic, α-ketoglutaric and citric acid. The applied bases are sodium and potassium hydroxide. The swelling behaviour was characterised by the degree of swelling and by the uptake of acids by the hydrogel in the swollen state. In the case of weak acids the properties of the swollen hydrogel as well as the phase transition temperature and phase transition acid concentration depends on the type of acids, whereas the properties of the shrunken state do not depend on the acid used. In the case of strong bases, the properties of the shrunken and swollen state depend on the ionic strength, but not on the base applied.

  4. Behaviors of acrylamide/itaconic acid hydrogels in uptake of uranyl ions from aqueous solutions

    SciTech Connect

    Karadag, E.; Saraydin, D.; Gueven, O.

    1995-12-01

    In this study, adsorptions of uranyl ions from two different aqueous uranyl solutions by acrylamide-itaconic acid hydrogels were investigated by a spectroscopic method. The hydrogels were prepared by irradiating with {gamma}-radiation. In the experiment of uranyl ions adsorption, Type II adsorption was found. One gram of acrylamide-itaconic acid hydrogels sorbed 178-219 mg uranyl ions from the solutions of uranyl acetate, 42-76 mg uranyl ions from the aqueous solutions of uranyl nitrate, while acrylamide hydrogel did not sorb any uranyl ion. For the hydrogel containing 40 mg of itaconic acid and irradiated to 3.73 kGy, swelling of the hydrogels was observed in water (1660%), in the aqueous solution of uranyl acetate (730%), and in the aqueous solution of uranyl nitrate (580%). Diffusions of water onto hydrogels were a non-Fickian type of diffusion, whereas diffusions of uranyl ions were a Fickian type of diffusion.

  5. Effect of various alkaline metal ions on electrochemical behavior of lead electrode in sulfuric acid solution

    NASA Astrophysics Data System (ADS)

    Hirai, Nobumitsu; Yamamoto, Yui

    2015-10-01

    The effect of various alkaline metal ions on electrochemical behavior of lead electrode in sulfuric acid solution has been investigated. It was found that "the specific anodic oxidation peak" appears at the cathodic scan in cyclic voltammogram of lead electrode in sulfuric acid solution containing Li2SO4, K2SO4, Na2SO4, Rb2SO4, or Cs2SO4. The height of the specific anodic oxidation peak varies with the alkaline sulfate in the solution; K2SO4 >> Na2SO4 > Cs2SO4 > Rb2SO4 > Li2SO4. It should be note that alkaline ions exist in lead sulfate formed on lead electrode in sulfuric acid solution containing potassium sulfate when the electrode was immersed in the solution at the rest potential for more than 1 h.

  6. Organic-inorganic interaction between hydroxyapatite and gelatin with the aging of gelatin in aqueous phosphoric acid solution.

    PubMed

    Chang, Myung Chul

    2008-11-01

    Hydroxyapatite (HAp)/gelatin (GEL) nanocomposite was prepared by the solution-precipitation process using Ca(OH)(2) in water and aqueous solution of H(3)PO(4) in GEL. Before the co precipitation process the GEL powders were dissolved in the aqueous phosphoric acid solution for the phosphorylation of GEL molecules. The chemical variation of the phosphorylated GEL macromolecules was investigated by using attenuated total reflection (ATR) measurement. The crystal growth of HAp became bigger with the long-time aging of the GEL molecules in the phosphoric acid solution, and it resulted from the reduction of length scale of the GEL molecules. The degree of the organic-inorganic interaction was decreased because of the degradation of the GEL macromolecules.

  7. Removal of fluoride in aqueous solution by adsorption on acid activated water treatment sludge

    NASA Astrophysics Data System (ADS)

    Vinitnantharat, Soydoa; Kositchaiyong, Sriwilai; Chiarakorn, Siriluk

    2010-06-01

    This paper reports the use of a pellet of adsorbent made from water treatment sludge (S) and acid activated water treatment sludge (SH) for removal of fluoride in the batch equilibration technique. The influence of pH, adsorbent dosage, temperature and effect of other ions were employed to find out the feasibility of acid activated adsorbent to remove fluoride to the permissible concentration of 0.7 mg/L. The results from the adsorption isotherm followed both Langmuir and Freundlich models and the highest fluoride removal was found for adsorbent activated with acetic acid at 2.0 mol/L. The optimum adsorbent dosage was found at 40 g/L, 0.01 mol/L acid activated adsorbent which was able to adsorb fluoride from 10 down to 0.11 mg/L. The adsorption capacity was decreased when the temperature increased. This revealed that the adsorption of fluoride on SH was exothermic. In the presence of nitrate and carbonate ions in the aqueous solution, fluoride removal efficiency of SH decreased from 94.4% to 86.6% and 90.8%, respectively. However, there is no significant effect in the presence of sulfate and chloride ions.

  8. Electrooxidation of homogentisic acid in aqueous and mixed solvent solutions: experimental and theoretical studies.

    PubMed

    Eslami, Marzieh; Namazian, Mansoor; Zare, Hamid R

    2013-03-01

    Electrochemical behavior of homogentisic acid (HGA) has been studied in both aqueous and mixed solvent solution of water-acetonitrile. Physicochemical parameters of the electrochemical reaction of HGA in these solutions are obtained experimentally by cyclic voltammetry method and are also calculated theoretically using accurate ab initio calculations (G3MP2//B3LYP). Solvation energies are calculated using the available solvation model of CPCM. The pH dependence of the redox activity of HGA in aqueous and the mixture solutions at different temperatures was used for the experimental determination of the standard reduction potential and changes of entropy, enthalpy, and Gibbs free energy for the studied reaction. The experimental standard redox potential of the compound in aqueous solution was obtained to be 0.636 V versus the standard hydrogen electrode. There is a good agreement between the theoretical and experimental values (0.702 and 0.636 V) for the standard electrode potential of HGA. The changes of thermodynamic functions of solvation are also calculated from the differences between the solution-phase experimental values and the gas-phase theoretical values. Finally, using the value of solvation energy of HGA in water and acetonitrile solvents which calculated by the CPCM model of energy, we proposed an equation for calculating the standard redox potential of HGA in mixture solution of water and acetonitrile. A good agreement between the result of electrode potential calculated by the proposed equation and the experimental value confirms the validity of the theoretical models used here and the accuracy of experimental methods.

  9. An investigation into the stability and sterility of citric acid solutions used for cough reflex testing.

    PubMed

    Falconer, James R; Wu, Zimei; Lau, Hugo; Suen, Joanna; Wang, Lucy; Pottinger, Sarah; Lee, Elaine; Alazawi, Nawar; Kallesen, Molly; Gargiulo, Derryn A; Swift, Simon; Svirskis, Darren

    2014-10-01

    Citric acid is used in cough reflex testing in clinical and research settings to assess reflexive cough in patients at risk of swallowing disorders. To address a lack of knowledge in this area, this study investigated the stability and sterility of citric acid solutions. Triplicate solutions of citric acid (0.8 M) in isotonic saline were stored at 4 ± 2 °C for up to 28 days and analysed by high-performance liquid chromatography. Microbiological sterility of freshly prepared samples and bulk samples previously used for 2 weeks within the hospital was determined using a pour plate technique. Microbial survival in citric acid was determined by inoculating Staphylococcus aureus, Escherichia coli, or Candida albicans into citric acid solution and monitoring the number of colony-forming units/mL over 40 min. Citric acid solutions remained stable at 4 °C for 28 days (98.4 ± 1.8 % remained). The freshly prepared and clinical samples tested were sterile. However, viability studies revealed that citric acid solution allows for the survival of C. albicans but not for S. aureus or E. coli. The microbial survival study showed that citric acid kills S. aureus and E. coli but has no marked effect on C. albicans after 40 min. Citric acid samples at 0.8 M remained stable over the 4-week testing period, with viable microbial cells absent from samples tested. However, C. albicans has the ability to survive in citric acid solution if inadvertently introduced in practice. For this reason, in clinical and research practice it is suggested to use single-use aliquots prepared aseptically which can be stored for up to 28 days at 4 °C.

  10. Interaction of some metals between marine-origin humic acids and aqueous solutions

    SciTech Connect

    Huljev, D.J.

    1986-08-01

    The interaction of metal ions (carrier-free form) in aquatic medium with humic acids is a complicated process depending on the properties of humic acids (elementary, chemical, and trace element composition), metals studied (valence, charge, chemical form, concentration), and medium used (pH, ionic strength). The use of radionuclides was found to be very suitable for a rapid and precise determination of the distribution coefficient K/sub d/ (ratio of the concentration of a certain trace metal association with a gram of humic acid over the concentration of the same trace metal per milliliter of solution) of the investigated system. Isolated humic acids from offshore sediments from the North Adriatic (Lim channel, near Rovinj, Yugoslavia) were characterized according to their elementary composition, the amount of products of hydrolysis, and the trace elements bound. All experiments were carried out between pH 3 and 5. It was found that conditions usually present at the site where humic acid interacts with metal ions (anaerobic conditions, H/sub 2/S) in brackish (21% S) and standard seawater (38% S) are determined in the pH range 3 to 5. The results of the pick-up (uptake) and replacement (release) experiments are presented as a distribution coefficient (K/sub d/), as a function of contact time. Processes of pick-up and replacement of a number of metals under various physicochemical conditions were investigated and special attention was paid to the influence of salinity. With the increase in NaCl concentration and pH in the system, the fixation of ruthenium, zinc, cobalt, and mercury by humic acids decreased.

  11. Electrochemical control of brightener in acid copper sulfate plating solutions

    SciTech Connect

    Bronson, M.J. . Kansas City Div.); Hawley, M.D. )

    1990-11-01

    Electrochemical methods have been evaluated that attempt the indirect measurement of the effective concentration of a brighter additive in acid copper sulfate plating baths. The procedures all employed electrodeposition of copper on a platinum working electrode under carefully controlled conditions of mass transport, time, temperature, and potential, followed by the measurement of the charge that was required to strip the copper deposit from the working electrode. The amount of charge that was required to strip the copper deposit at a given concentration of additive varied significantly from fresh to production baths and from lot to lot of the additive. The feasibility of using electrochemical methods to control brightener additive in acid copper sulfate plating baths is discussed. 3 figs., 11 refs.

  12. Interfacial structures of acidic and basic aqueous solutions

    SciTech Connect

    Tian, C.; Ji, N.; Waychunas, G.; Shen, Y.R.

    2008-10-20

    Phase-sensitive sum-frequency vibrational spectroscopy was used to study water/vapor interfaces of HCl, HI, and NaOH solutions. The measured imaginary part of the surface spectral responses provided direct characterization of OH stretch vibrations and information about net polar orientations of water species contributing to different regions of the spectrum. We found clear evidence that hydronium ions prefer to emerge at interfaces. Their OH stretches contribute to the 'ice-like' band in the spectrum. Their charges create a positive surface field that tends to reorient water molecules more loosely bonded to the topmost water layer with oxygen toward the interface, and thus enhances significantly the 'liquid-like' band in the spectrum. Iodine ions in solution also like to appear at the interface and alter the positive surface field by forming a narrow double-charge layer with hydronium ions. In NaOH solution, the observed weak change of the 'liquid-like' band and disappearance of the 'ice-like' band in the spectrum indicates that OH{sup -} ions must also have excess at the interface. How they are incorporated in the interfacial water structure is however not clear.

  13. Determination of acid ionization constants for weak acids by osmometry and the instrumental analysis self-evaluation feedback approach to student preparation of solutions

    NASA Astrophysics Data System (ADS)

    Kakolesha, Nyanguila

    One focus of this work was to develop of an alternative method to conductivity for determining the acid ionization constants. Computer-controlled osmometry is one of the emerging analytical tools in industrial research and clinical laboratories. It is slowly finding its way into chemistry laboratories. The instrument's microprocessor control ensures shortened data collection time, repeatability, accuracy, and automatic calibration. The equilibrium constants of acetic acid, chloroacetic acid, bromoacetic acid, cyanoacetic acid, and iodoacetic acid have been measured using osmometry and their values compared with the existing literature values obtained, usually, from conductometric measurements. Ionization constant determined by osmometry for the moderately strong weak acids were in reasonably good agreement with literature values. The results showed that two factors, the ionic strength and the osmotic coefficient, exert opposite effects in solutions of such weak acids. Another focus of the work was analytical chemistry students solution preparation skills. The prevailing teacher-structured experiments leave little room for students' ingenuity in quantitative volumetric analysis. The purpose of this part of the study was to improve students' skills in making solutions using instrument feedback in a constructivist-learning model. After making some solutions by weighing and dissolving solutes or by serial dilution, students used the spectrophotometer and the osmometer to compare their solutions with standard solutions. Students perceived the instrument feedback as a nonthreatening approach to monitoring the development of their skill levels and liked to clarify their understanding through interacting with an instructor-observer. An assessment of the instrument feedback and the constructivist model indicated that students would assume responsibility for their own learning if given the opportunity. This study involved 167 students enrolled in Quantitative Chemical

  14. Chemical Corrosion of Liquid-Phase Sintered SiC in Acidic/Alkaline Solutions Part 1. Corrosion in HNO3 Solution

    NASA Astrophysics Data System (ADS)

    Zhang, Lei; Zhang, Ming; He, Xinnong; Tang, Wenming

    2016-03-01

    The corrosion behavior of the liquid-phase sintered SiC (LPS-SiC) was studied by dipping in 3.53 mol/L HNO3 aqueous solution at room temperature and 70 °C, respectively. The weight loss, strength reduction and morphology evolution of the SiC specimens during corroding were revealed and also the chemical corrosion process and mechanism of the SiC specimens in the acidic solution were clarified. The results show that the corrosion of the LPS-SiC specimens in the HNO3 solution is selective. The SiC particles are almost free from corrosion, but the secondary phases of BaAl2Si2O8 (BAS) and Y2Si2O7 are corroded via an acid-alkali neutralization reaction. BAS has a higher corrosion rate than Y2Si2O7, resulting in the formation of the bamboo-leaf-like corrosion pits. As the SiC specimens etched in the HNO3 solution at room temperature for 75 days, about 80 μm thickness corrosion layer forms. The weight loss and bending strength reduction of the etched SiC specimens are 2.6 mg/cm2 and 52%, respectively. The corrosion of the SiC specimens is accelerated in the 70 °C HNO3 solution with a rate about five times bigger than that in the same corrosion medium at room temperature.

  15. DYNAMIC CONDUCTIVITY MEASUREMENTS IN HUMIC AND FULVIC ACID SOLUTIONS. (R828158)

    EPA Science Inventory

    Conductivity changes of dilute aqueous humic and fulvic acids solutions were monitored after the addition of small quantities of Cu, Cd, Pb, and Zn. The solutions were stirred at a constant and reproducible rate, and measurements proceeded until stable conductivities were atta...

  16. Real-time monitoring of nucleic acid ligation in homogenous solutions using molecular beacons.

    PubMed

    Tang, Zhiwen; Wang, Kemin; Tan, Weihong; Li, Jun; Liu, Lingfeng; Guo, Qiuping; Meng, Xiangxian; Ma, Changbei; Huang, Shasheng

    2003-12-01

    Nucleic acids ligation is a vital process in the repair, replication and recombination of nucleic acids. Traditionally, it is assayed by denatured gel electrophoresis and autoradiography, which are not sensitive, and are complex and discontinuous. Here we report a new approach for ligation monitoring using molecular beacon DNA probes. The molecular beacon, designed in such a way that its sequence is complementary with the product of the ligation process, is used to monitor the nucleic acid ligation in a homogeneous solution and in real-time. Our method is fast and simple. We are able to study nucleic acids ligation kinetics conveniently and to determine the activity of DNA ligase accurately. We have studied different factors that influence DNA ligation catalyzed by T4 DNA ligase. The major advantages of our method are its ultrasensitivity, excellent specificity, convenience and real-time monitoring in homogeneous solution. This method will be widely useful for studying nucleic acids ligation process and other nucleic acid interactions.

  17. SULFURIC ACID REMOVAL PROCESS EVALUATION: LONG-TERM RESULTS

    SciTech Connect

    Gary M. Blythe; Richard McMillan

    2002-07-03

    longer-term (approximately 25-day) full-scale tests on two different units. The longer-term tests were conducted to confirm the effectiveness of the sorbents tested over extended operation on two different boilers, and to determine balance-of-plant impacts. The first long-term test was conducted on FirstEnergy's BMP, Unit 3, and the second test was conducted on AEP's Gavin Plant, Unit 1. The Gavin Plant testing provided an opportunity to evaluate the effects of sorbent injected into the furnace on SO{sub 3} formed across an operating SCR reactor. This report presents the results from those long-term tests. The tests determined the effectiveness of injecting commercially available magnesium hydroxide slurry (Gavin Plant) and byproduct magnesium hydroxide slurry (both Gavin Plant and BMP) for sulfuric acid control. The results show that injecting either slurry could achieve up to 70 to 75% overall sulfuric acid removal. At BMP, this overall removal was limited by the need to maintain acceptable electrostatic precipitator (ESP) particulate control performance. At Gavin Plant, the overall sulfuric acid removal was limited because the furnace injected sorbent was less effective at removing SO{sub 3} formed across the SCR system installed on the unit for NOX control than at removing SO{sub 3} formed in the furnace. The long-term tests also determined balance-of-plant impacts from slurry injection during the two tests. These include impacts on boiler back-end temperatures and pressure drops, SCR catalyst properties, ESP performance, removal of other flue gas species, and flue gas opacity. For the most part the balance-of-plant impacts were neutral to positive, although adverse effects on ESP performance became an issue during the BMP test.

  18. Ab Initio Molecular Dynamics Simulations of Amino Acids in Aqueous Solutions: Estimating pKa Values from Metadynamics Sampling.

    PubMed

    Tummanapelli, Anil Kumar; Vasudevan, Sukumaran

    2015-09-17

    Changes in the protonation and deprotonation of amino acid residues in proteins play a key role in many biological processes and pathways. Here, we report calculations of the free-energy profile for the protonation-deprotonation reaction of the 20 canonical α amino acids in aqueous solutions using ab initio Car-Parrinello molecular dynamics simulations coupled with metadynamics sampling. We show here that the calculated change in free energy of the dissociation reaction provides estimates of the multiple pKa values of the amino acids that are in good agreement with experiment. We use the bond-length-dependent number of the protons coordinated to the hydroxyl oxygen of the carboxylic and the amine groups as the collective variables to explore the free-energy profiles of the Bronsted acid-base chemistry of amino acids in aqueous solutions. We ensure that the amino acid undergoing dissociation is solvated by at least three hydrations shells with all water molecules included in the simulations. The method works equally well for amino acids with neutral, acidic and basic side chains and provides estimates of the multiple pKa values with a mean relative error, with respect to experimental results, of 0.2 pKa units. PMID:26331783

  19. Ab Initio Molecular Dynamics Simulations of Amino Acids in Aqueous Solutions: Estimating pKa Values from Metadynamics Sampling.

    PubMed

    Tummanapelli, Anil Kumar; Vasudevan, Sukumaran

    2015-09-17

    Changes in the protonation and deprotonation of amino acid residues in proteins play a key role in many biological processes and pathways. Here, we report calculations of the free-energy profile for the protonation-deprotonation reaction of the 20 canonical α amino acids in aqueous solutions using ab initio Car-Parrinello molecular dynamics simulations coupled with metadynamics sampling. We show here that the calculated change in free energy of the dissociation reaction provides estimates of the multiple pKa values of the amino acids that are in good agreement with experiment. We use the bond-length-dependent number of the protons coordinated to the hydroxyl oxygen of the carboxylic and the amine groups as the collective variables to explore the free-energy profiles of the Bronsted acid-base chemistry of amino acids in aqueous solutions. We ensure that the amino acid undergoing dissociation is solvated by at least three hydrations shells with all water molecules included in the simulations. The method works equally well for amino acids with neutral, acidic and basic side chains and provides estimates of the multiple pKa values with a mean relative error, with respect to experimental results, of 0.2 pKa units.

  20. Spill behaviour using REACTPOOL. Part I. Results for accidental releases of chlorosulphonic acid (HSO(3)Cl).

    PubMed

    Kapias, T; Griffiths, R F

    2001-01-29

    Chlorosulphonic acid is a toxic, highly reactive and corrosive substance that exists in its liquid form at ambient conditions. Its major hazardous potential comes from the clouds of hydrogen chloride and sulphuric acid mist produced whenever this chemical escapes from containment and is exposed to moisture. It decomposes violently and sometimes explosively in the presence of water, liberating heat. On spillage it creates liquid pools that can either boil or evaporate. There are three sources of water available for reaction: free ground water, substrate water and atmospheric moisture. Hydrogen chloride gas or aqueous solution and sulphuric acid liquid are produced by the hydrolysis reaction. This paper describes the dangers involved in cases of accidental releases of chlorosulphonic acid, referring to its properties, toxicity data and mitigation tests. It also reports results of pool behaviour using REACTPOOL [T. Kapias, R.F. Griffiths, C. Stefanidis, J. Haz. Mat., submitted for publication]. These results indicate that the pool behaviour is governed mainly by the amount of water available for reaction. Surface roughness and wind speed also have a significant effect on the results. A discussion of the results in comparison with those for other water reactive substances is presented in Part III of this series of papers [T. Kapias, R.F. Griffiths, J. Haz. Mat., submitted for publication]. The generated cloud will initially contain chlorosulphonic acid, hydrogen chloride and sulphuric acid with numerous processes taking place. Initially, it is usually denser than air. Although chlorosulphonic acid has been involved in major hazard incidents, there are no experimental data relevant to the modelling requirements. Use of REACTPOOL provides insights into the major hazard role of this substance.

  1. Early retinoic acid deprivation in developing zebrafish results in microphthalmia.

    PubMed

    Le, Hong-Gam T; Dowling, John E; Cameron, D Joshua

    2012-09-01

    Vitamin A deficiency causes impaired vision and blindness in millions of children around the world. Previous studies in zebrafish have demonstrated that retinoic acid (RA), the acid form of vitamin A, plays a vital role in early eye development. The objective of this study was to describe the effects of early RA deficiency by treating zebrafish with diethylaminobenzaldehyde (DEAB), a potent inhibitor of the enzyme retinaldehyde dehydrogenase (RALDH) that converts retinal to RA. Zebrafish embryos were treated for 2 h beginning at 9 h postfertilization. Gross morphology and retinal development were examined at regular intervals for 5 days after treatment. The optokinetic reflex (OKR) test, visual background adaptation (VBA) test, and the electroretinogram (ERG) were performed to assess visual function and behavior. Early treatment of zebrafish embryos with 100 μM DEAB (9 h) resulted in reduced eye size, and this microphthalmia persisted through larval development. Retinal histology revealed that DEAB eyes had significant developmental abnormalities but had relatively normal retinal lamination by 5.5 days postfertilization. However, the fish showed neither an OKR nor a VBA response. Further, the retina did not respond to light as measured by the ERG. We conclude that early deficiency of RA during eye development causes microphthalmia as well as other visual defects, and that timing of the RA deficiency is critical to the developmental outcome.

  2. Extraction of steroidal glucosiduronic acids from aqueous solutions by anionic liquid ion-exchangers

    PubMed Central

    Mattox, Vernon R.; Litwiller, Robert D.; Goodrich, June E.

    1972-01-01

    A pilot study on the extraction of three steroidal glucosiduronic acids from water into organic solutions of liquid ion-exchangers is reported. A single extraction of a 0.5mm aqueous solution of either 11-deoxycorticosterone 21-glucosiduronic acid or cortisone 21-glucosiduronic acid with 0.1m-tetraheptylammonium chloride in chloroform took more than 99% of the conjugate into the organic phase; under the same conditions, the very polar conjugate, β-cortol 3-glucosiduronic acid, was extracted to the extent of 43%. The presence of a small amount of chloride, acetate, or sulphate ion in the aqueous phase inhibited extraction, but making the aqueous phase 4.0m with ammonium sulphate promoted extraction strongly. An increase in the concentration of ion-exchanger in the organic phase also promoted extraction. The amount of cortisone 21-glucosiduronic acid extracted by tetraheptylammonium chloride over the pH range of 3.9 to 10.7 was essentially constant. Chloroform solutions of a tertiary, a secondary, or a primary amine hydrochloride also will extract cortisone 21-glucosiduronic acid from water. The various liquid ion exchangers will extract steroidal glucosiduronic acid methyl esters from water into chloroform, although less completely than the corresponding free acids. The extraction of the glucosiduronic acids from water by tetraheptylammonium chloride occurs by an ion-exchange process; extraction of the esters does not involve ion exchange. PMID:5075264

  3. The amino acid's backup bone - storage solutions for proteomics facilities.

    PubMed

    Meckel, Hagen; Stephan, Christian; Bunse, Christian; Krafzik, Michael; Reher, Christopher; Kohl, Michael; Meyer, Helmut Erich; Eisenacher, Martin

    2014-01-01

    Proteomics methods, especially high-throughput mass spectrometry analysis have been continually developed and improved over the years. The analysis of complex biological samples produces large volumes of raw data. Data storage and recovery management pose substantial challenges to biomedical or proteomic facilities regarding backup and archiving concepts as well as hardware requirements. In this article we describe differences between the terms backup and archive with regard to manual and automatic approaches. We also introduce different storage concepts and technologies from transportable media to professional solutions such as redundant array of independent disks (RAID) systems, network attached storages (NAS) and storage area network (SAN). Moreover, we present a software solution, which we developed for the purpose of long-term preservation of large mass spectrometry raw data files on an object storage device (OSD) archiving system. Finally, advantages, disadvantages, and experiences from routine operations of the presented concepts and technologies are evaluated and discussed. This article is part of a Special Issue entitled: Computational Proteomics in the Post-Identification Era. Guest Editors: Martin Eisenacher and Christian Stephan. PMID:23722089

  4. The amino acid's backup bone - storage solutions for proteomics facilities.

    PubMed

    Meckel, Hagen; Stephan, Christian; Bunse, Christian; Krafzik, Michael; Reher, Christopher; Kohl, Michael; Meyer, Helmut Erich; Eisenacher, Martin

    2014-01-01

    Proteomics methods, especially high-throughput mass spectrometry analysis have been continually developed and improved over the years. The analysis of complex biological samples produces large volumes of raw data. Data storage and recovery management pose substantial challenges to biomedical or proteomic facilities regarding backup and archiving concepts as well as hardware requirements. In this article we describe differences between the terms backup and archive with regard to manual and automatic approaches. We also introduce different storage concepts and technologies from transportable media to professional solutions such as redundant array of independent disks (RAID) systems, network attached storages (NAS) and storage area network (SAN). Moreover, we present a software solution, which we developed for the purpose of long-term preservation of large mass spectrometry raw data files on an object storage device (OSD) archiving system. Finally, advantages, disadvantages, and experiences from routine operations of the presented concepts and technologies are evaluated and discussed. This article is part of a Special Issue entitled: Computational Proteomics in the Post-Identification Era. Guest Editors: Martin Eisenacher and Christian Stephan.

  5. Production and stability of chlorine dioxide in organic acid solutions as affected by pH, type of acid, and concentration of sodium chlorite, and its effectiveness in inactivating Bacillus cereus spores.

    PubMed

    Kim, Hoikyung; Kang, Youngjee; Beuchat, Larry R; Ryu, Jee-Hoon

    2008-12-01

    We studied the production and stability of chlorine dioxide (ClO(2)) in organic acid solutions and its effectiveness in killing Bacillus cereus spores. Sodium chlorite (5000, 10,000, or 50,000 microg/ml) was added to 5% acetic, citric, or lactic acid solution, adjusted to pH 3.0, 4.0, 5.0, or 6.0, and held at 21 degrees C for up to 14 days. The amount of ClO(2) produced was higher as the concentration of sodium chlorite was increased and as the pH of the acid solutions was decreased. However, the stability in production of ClO(2) was enhanced by increasing the pH of the organic acid solutions. To evaluate the lethal activity of ClO(2) produced in various acid solutions as affected by acidulant and pH, suspensions of B. cereus spores were treated at 21 degrees C for 1, 3, 5, or 10 min in hydrochloric acid or organic acid solutions (pH 3.0, 4.0, 5.0, or 6.0) containing ClO(2) at concentrations of 100, 50, or 25 microg/ml. Populations of viable spores treated with ClO(2) at concentrations of 100 or 50 microg/ml in organic acid solutions decreased more rapidly than populations treated with the same concentrations of ClO(2) in HCl. Rates of inactivation tended to increase with higher pH of ClO(2) solutions. Results show that ClO(2) formed in organic acid solutions has higher stability and is more lethal to B. cereus spores than ClO(2) formed at the same concentration in HCl solution. This finding emphasizes the benefits of using organic acid solutions to prepare ClO(2) intended for use as an antimicrobial.

  6. Method for extracting lanthanides and actinides from acid solutions by modification of Purex solvent

    DOEpatents

    Horwitz, E.P.; Kalina, D.G.

    1984-05-21

    A process has been developed for the extraction of multivalent lanthanide and actinide values from acidic waste solutions, and for the separation of these values from fission product and other values, which utilizes a new series of neutral bi-functional extractants, the alkyl(phenyl)-N, N-dialkylcarbamoylmethylphosphine oxides, in combination with a phase modifier to form an extraction solution. The addition of the extractant to the Purex process extractant, tri-n-butylphosphate in normal paraffin hydrocarbon diluent, will permit the extraction of multivalent lanthanide and actinide values from 0.1 to 12.0 molar acid solutions.

  7. Degradation of berenil (diminazene aceturate) in acidic aqueous solution.

    PubMed

    Campbell, Michael; Prankerd, Richard J; Davie, Ashley S; Charman, William N

    2004-10-01

    The trypanocide berenil was assessed for chemical stability over the pH range 1-8 at 37 degrees C and 0.2 M ionic strength. It was found to be sufficiently unstable under acid conditions that its therapeutic efficacy is most likely severely compromised when administered orally. At pH 3, the half-life was 35 min, decreasing to 1.5 min at pH 1.75. Reaction rate constants were corrected for the effects of buffer catalysis and were found to range from 2.00 min(-1) at pH 1 to 6.1 x 10(-6) min(-1) at pH 8. The pH-rate profile displayed a region (pH 1-4) where specific acid catalysis was dominant, followed by a transitional region (pH 5-7), and finally a region (pH >7) where uncatalysed degradation was most important. It is recommended that berenil be enteric coated for formulations to be used in treating Third World parasitic diseases. PMID:15482649

  8. Extraction of nitric acid, uranyl nitrate, and bismuth nitrate from aqueous nitric acid solutions with CMPO

    SciTech Connect

    Spencer, B.B.

    1995-08-01

    DOE sponsored development of the transuranium extraction (TRUEX) process for removing actinides from radioactive wastes. The solvent is a mixture of CMPO and TBP. Since the extraction characteristics of CMPO are not as well understood as those of TBP, the extraction of nitric acid, uranyl nitrate, and bismuth nitrate with CMPO (dissolved in n-dodecane) were studied. Results indicate that CMPO extracts nitric acid with a 1:1 stoichiometry; equilibrium constant is 2. 660{plus_minus}0.092 at 25 C, and extraction enthalpy is -5. 46{plus_minus}0.46 kcal/mol. Slope analysis indicates that uranyl nitrate extracts with a mixed equilibria of 1:1 and 2:1 stoichiometries in nearly equal proportion. Equil. constant of the 2: 1 extraction was 1.213 {times} 10{sup 6}{plus_minus}3.56 {times} 10{sup 4} at 25 C; reaction enthalpy was -9.610{plus_minus}0.594 kcal/mol. Nitration complexation constant is 8.412{plus_minus}0.579, with an enthalpy of -10.72{plus_minus}1.87 kcal/mol. Bismuth nitrate also extracts with a mixed equilibria of (perhaps) 1:1 and 2:1 stoichiometries. A 2:1 extraction equilibrium and a nitrate complexation adequately model the data. Kinetics and enthalpies were also measured.

  9. Interaction of Some Amino Acids with Sodium Dodecyl Sulphate in Aqueous Solution at Different Temperatures

    NASA Astrophysics Data System (ADS)

    Ali, Anwar; Itoo, Firdoos Ahmad; Ansari, Nizamul Haque

    2011-05-01

    The density ρ, and viscosity η of 0.00, 0.05, 0.10, 0.15, and 0.20 mol kg-1 glycine (Gly), dlalanine (Ala), dl-serine (Ser), and dl-valine (Val) have been measured in 0.002 mol kg-1 aqueous sodium dodecyl sulphate (SDS) at 298.15, 303.15, 308.15, and 313.15 K. These data have been used to calculate the apparent molar volume φv, infinite dilution apparent molar volume φv°, and the standard partial molar volumes of transfer φv° (tr), of the amino acids from water to the aqueous SDS solutions. Falkenhagen coefficient A, Jones-Dole coefficient B, free energies of activation per mole of solvent (aqueous SDS) Δμ1°*, and per mole solute (amino acids) Δμ2°*, also enthalpy ΔH* and entropy ΔS* of activation of viscous flow were evaluated using viscosity data. The molar refraction RD was calculated by using experimental values of the refractive index nD of the systems. The results have been interpreted in terms of ion-ion, ion-polar and hydrophobic-hydrophobic group interactions. The volume of the transfer data suggest that ion-ion intertactions are predominant.

  10. Free radicals from 1-palmitoyl-2-arachidonoylphosphatidylcholine liposomes in Fe2+/ascorbic acid solution.

    PubMed

    Yoshida, T; Otake, H; Aramaki, Y; Hara, T; Tsuchiya, S; Hamada, A; Utsumi, H

    1996-06-01

    The generation of free radicals during the lipid peroxidation of liposomes composed of 1-palmitoyl-2-arachidonoylphosphatidylcholine (PAPC-liposome) in Fe2+/ascorbic acid (AsA) solution was studied by the ESR spin trapping technique. A carbon-centered radical adduct was observed using alpha-(4-pyridyl-1-oxide)-N-tert-butyl-nitorone (4-POBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO), but no oxygen-centered radicals such as .OH, LO., and LOO. were observed. The lipid peroxidation evaluated as 2-thiobarbituric acid reactive substances was inhibited by the addition of 4-POBN. The intensity of this inhibitory effect was dependent on the time when 4-POBN was added to the mixture of PAPC-liposomes and Fe2+/AsA solution, and no inhibitory effect could be observed after 4 min. The signal intensity of the carbon-centered radical adduct was dependent on the lipid concentration of PAPC-liposomes. These results suggest that the alkyl radicals generated from PAPC-liposome peroxidation induced by Fe2+/AsA were trapped by DMPO or 4-POBN at an earlier stage of lipid peroxidation. PMID:8799472

  11. Solute-enhanced production of gamma-valerolactone (GVL) from aqueous solutions of levulinic acid

    DOEpatents

    Dumesic, James A; Wettstein, Stephanie G; Alonso, David Martin; Gurbuz, Elif Ispir

    2015-02-24

    A method to produce levulinic acid (LA) and gamma-valerolactone (GVL) from biomass-derived cellulose or lignocellulose by selective extraction of LA using GVL and optionally converting the LA so isolated into GVL, with no purifications steps required to yield the GVL.

  12. The solvent extraction of Americium(III) by 2,6-bis[(diphenylphosphino)-methyl]pyridine N,P,P` trioxide from nitric acid and hydrochloric acid solutions

    SciTech Connect

    Bond, E.M.; Engelhardt, U.; Deere, T.P.; Rapko, B.M.; Paine, R.T.

    1997-12-31

    The liquid/liquid extractions of Am(III) from nitric acid and hydrochloric acid solutions with chloroform solutions of 2,6-bis[(diphenylphosphino)methyl]pyridine N,P,P{prime} trioxide will be described. Americium(III) extracts well from high concentration nitric acid solutions (D>3000 at 6M nitric acid) and can be back extracted from the organic phase at 0.01M Nitric Acid. Americium(III) exhibits modest extraction from hydrochloric acid solutions (D=2.2 at 5M hydrochloric acid) and can be back extracted from the organic phase at 0.1M hydrochloric acid. The ligand dependency data suggest that two ligand molecules are coordinated to americium in the nitric acid system and three ligand molecules are coordinated to the americium in the hydrochloric acid system.

  13. Solution properties and emulsification properties of amino acid-based gemini surfactants derived from cysteine.

    PubMed

    Yoshimura, Tomokazu; Sakato, Ayako; Esumi, Kunio

    2013-01-01

    Amino acid-based anionic gemini surfactants (2C(n)diCys, where n represents an alkyl chain with a length of 10, 12, or 14 carbons and "di" and "Cys" indicate adipoyl and cysteine, respectively) were synthesized using the amino acid cysteine. Biodegradability, equilibrium surface tension, and dynamic light scattering were used to characterize the properties of gemini surfactants. Additionally, the effects of alkyl chain length, number of chains, and structure on these properties were evaluated by comparing previously reported gemini surfactants derived from cystine (2C(n)Cys) and monomeric surfactants (C(n)Cys). 2C(n)diCys shows relatively higher biodegradability than does C(n)Cys and previously reported sugar-based gemini surfactants. Both critical micelle concentration (CMC) and surface tension decrease when alkyl chain length is increased from 10 to 12, while a further increase in chain length to 14 results in increased CMC and surface tension. This indicates that long-chain gemini surfactants have a decreased aggregation tendency due to the steric hindrance of the bulky spacer as well as premicelle formation at concentrations below the CMC and are poorly packed at the air/water interface. Formation of micelles (measuring 2 to 5 nm in solution) from 2C(n)diCys shows no dependence on alkyl chain length. Further, shaking the mixtures of aqueous 2C(n)diCys surfactant solutions and squalane results in the formation of oil-in-water type emulsions. The highly stable emulsions are formed using 2C₁₂diCys or 2C₁₄diCys solution and squalane in a 1:1 or 2:1 volume ratio.

  14. THE KINETICS OF SAPONIFICATION OF IODOACETIC ACID BY SODIUM HYDROXIDE AND BY CERTAIN ALKALINE BUFFER SOLUTIONS.

    PubMed

    Brdicka, R

    1936-07-20

    1. The rate of the saponification of iodoacetic acid in sodium hydroxide and alkaline buffer solutions yielding glycollic acid was measured by means of Heyrovský's polarographic method. 2. From the bimolecular velocity constants, increasing with the ionic strength of the solution, the Brönsted factor, F, which characterizes the primary salt effect, was calculated. 3. In the borate buffer solutions the monomolecular constants of the saponification were determined which, at values above the pH of neutralization of boric acid, show a proportionality to the concentration of hydroxyl anions. Below the pH of neutralization of boric acid, they are proportional to the concentration of borate anions.

  15. Formation of Amino Acids on the Sonolysis of Aqueous Solutions Containing Acetic Acid, Methane, or Carbon Dioxide, in the Presence of Nitrogen Gas.

    PubMed

    Dharmarathne, Leena; Grieser, Franz

    2016-01-21

    The sonolysis of aqueous solutions containing acetic acid, methane, or carbon dioxide in the presence of nitrogen gas was found to produce a number of different amino acids at a rate of ∼1 to 100 nM/min, using ultrasound at an operating power of 70 W and 355 kHz. Gas-phase elementary reactions are suggested, and discussed, to account for the formation of the complex biomolecules from the low molar mass solutes used. On the basis of the results, a new hypothesis is presented to explain the formation of amino acids under primitive atmospheric conditions and how their formation may be linked to the eventual abiotic genesis of life on Earth.

  16. Formation of Amino Acids on the Sonolysis of Aqueous Solutions Containing Acetic Acid, Methane, or Carbon Dioxide, in the Presence of Nitrogen Gas.

    PubMed

    Dharmarathne, Leena; Grieser, Franz

    2016-01-21

    The sonolysis of aqueous solutions containing acetic acid, methane, or carbon dioxide in the presence of nitrogen gas was found to produce a number of different amino acids at a rate of ∼1 to 100 nM/min, using ultrasound at an operating power of 70 W and 355 kHz. Gas-phase elementary reactions are suggested, and discussed, to account for the formation of the complex biomolecules from the low molar mass solutes used. On the basis of the results, a new hypothesis is presented to explain the formation of amino acids under primitive atmospheric conditions and how their formation may be linked to the eventual abiotic genesis of life on Earth. PMID:26695890

  17. Acid gas absorption in aqueous solutions of mixed amines

    SciTech Connect

    Rinker, E.B.; Ashour, S.S.; Sandall, O.C.

    1996-12-31

    A mass transfer model has been developed to describe the rate of absorption (or desorption) of H{sub 2}S and CO{sub 2} in aqueous blends of a tertiary and a secondary or a primary amine. The model is based on penetration theory, and all significant chemical reactions are incorporated in the model. The reactions are taken to be reversible, with reactions involving only a proton transfer considered to be at equilibrium. The particular amines studied in this research were methyldiethanolamine (MDEA), a tertiary amine, and diethanolamine (DEA), a secondary amine. Key physicochemical data needed in the model, such as diffusion coefficients, kinetic rate constants, and gas solubilities, were measured. Experimental absorption rates of CO{sub 2} and H{sub 2}S were measured in a model gas-liquid contacting device and were compared with model predictions. Experiments were carried out for single amine solutions (both MDEA and DEA) and for amine blends.

  18. Formation of aromatic compounds from carbohydrates. X reaction of xylose, glucose, and glucuronic acid in acidic solution at 300C

    SciTech Connect

    Theander, O.; Nelson, D.A.; Hallen, R.T.

    1987-04-01

    For several years our respective groups have investigated the formation of aromatic compounds from carbohydrates in aqueous solution at various pH-values under reflux or hydrothermolytic conditions. For instance, previous papers in this series concerned the degradation of hexoses, pentoses, erythrose, dihydroxyacetone, and hexuronic acids to phenolic and enolic components. Of particular interest were the isolation and identification of catechols, an acetophenone, and chromones from pentoses and hexuronic acids at pH 4.5. The formation of these compounds, as well as reductic acid, was found to be more pronounced than that of 2-furaldehyde under acidic conditions. The aromatic precursors of 3 and 4 were also isolated from these reaction mixtures. This is in contrast to the high yields of 2 obtained from pentoses and hexuronic acids at very low pH.

  19. Folic Acid Supplementation and Preterm Birth: Results from Observational Studies

    PubMed Central

    Franchi, Massimo

    2014-01-01

    Introduction. Folic acid (FA) supplementation is recommended worldwide in the periconceptional period for the prevention of neural tube defects. Due to its involvement in a number of cellular processes, its role in other pregnancy outcomes such as miscarriage, recurrent miscarriage, low birth weight, preterm birth (PTB), preeclampsia, abruptio placentae, and stillbirth has been investigated. PTB is a leading cause of perinatal mortality and morbidity; therefore its association with FA supplementation is of major interest. The analysis of a small number of randomized clinical trials (RCTs) has not found a beneficial role of FA in reducing the rate of PTBs. Aim of the Study. The aim of this review was to examine the results from recent observational studies about the effect of FA supplementation on PTB. Materials and Methods. We carried out a search on Medline and by manual search of the observational studies from 2009 onwards that analyzed the rate of PTB in patients who received supplementation with FA before and/or throughout pregnancy. Results. The results from recent observational studies suggest a slight reduction of PTBs that is not consistent with the results from RCTs. Further research is needed to better understand the role of FA supplementation before and during pregnancy in PTB. PMID:24724083

  20. Ultrasonic Studies of 4-Aminobutyric Acid in Aqueous Metformin Hydrochloride Solutions at Different Temperatures

    NASA Astrophysics Data System (ADS)

    Rajagopal, K.; Jayabalakrishnan, S. S.

    2010-12-01

    Ultrasonic speeds and density data of 4-aminobutyric acid in 0.05 M, 0.10 M, and 0.15 M aqueous metformin hydrochloride (MFHCl) solutions are measured at 308.15 K, 313.15 K, and 318.15 K. The isentropic compressibility ( k S ), the change in isentropic compressibility (Δ k S ), the relative change in isentropic compressibility ({Δ k_S/k_S^0}), the apparent molal compressibility ({k_φ}), the limiting apparent molal compressibility ({k_φ^0 }), the transfer limiting apparent molal compressibility ({Δ k_φ^0}), the hydration number ( n H), and the pair and triplet interaction parameters ( k AH, k AHH) are estimated. The above parameters are used to interpret the solute-solute and solute-solvent interactions of 4-aminobutyric acid in aqueous MFHCl solutions.

  1. Reaction behavior of Ni-Re alloys during direct current polarization in sulfuric acid solutions

    NASA Astrophysics Data System (ADS)

    Bryukvin, V. A.; Elemesov, T. B.; Levchuk, O. M.; Bol'shikh, A. O.

    2016-01-01

    The macrokinetic regularities of the reactivity of synthesized Ni-Re (20 and 60 wt %) alloys in a sulfuric acid solution (100 g/L, 25-40°C) during direct current polarization are studied using physicochemical methods. The phase composition of the synthesized alloys is determined by the formation of solid solutions as a function of the initial Ni/Re weight ratio. These are two types of nickel solid solutions (Ni16Re0.2 and Ni14Re0.9) and one rhenium solution (Ni1.1Re). These solid solutions are anodically oxidized in the sequence of their structural rearrangement Ni16Re0.2 → Ni14Re0.9 → Ni1.1Re with a combined transition of the metals into an electrolyte solution. These solid solutions provide the reduction of Ni3+ to Ni2+ due to the depolarization ability of rhenium, being their component.

  2. Methylene blue adsorption from aqueous solution by activated carbon: effect of acidic and alkaline solution treatments.

    PubMed

    Ijagbemi, Christianah O; Chun, Ji I; Han, Da H; Cho, Hye Y; O, Se J; Kim, Dong S

    2010-01-01

    The removal of Methylene Blue (MB) from aqueous solution using activated carbon (AC) has been investigated. Adsorption experiments were conducted and the maximum adsorption capacity was determined. The effect of experimental parameters such as pH, dye concentration and temperature were studied on the adsorption process. Equilibrium data were mathematically modeled using the Langmuir and Freundlich adsorption models to describe the equilibrium isotherms at different dye concentrations and temperature. Parameters of best-fit model were calculated and discussed. To understand the mechanism of adsorption, kinetic models were employed to follow the adsorption processes; the pseudo-first-order best described the adsorption of MB onto AC. It was found that pH plays a major role in the adsorption process; adsorption capacity was influenced by the physical and surface chemical properties of carbon and the pH of the solution. 99.0% MB removal was achieved at equilibrium.

  3. Metabolic engineering of yeast to produce fatty acid-derived biofuels: bottlenecks and solutions.

    PubMed

    Sheng, Jiayuan; Feng, Xueyang

    2015-01-01

    Fatty acid-derived biofuels can be a better solution than bioethanol to replace petroleum fuel, since they have similar energy content and combustion properties as current transportation fuels. The environmentally friendly microbial fermentation process has been used to synthesize advanced biofuels from renewable feedstock. Due to their robustness as well as the high tolerance to fermentation inhibitors and phage contamination, yeast strains such as Saccharomyces cerevisiae and Yarrowia lipolytica have attracted tremendous attention in recent studies regarding the production of fatty acid-derived biofuels, including fatty acids, fatty acid ethyl esters, fatty alcohols, and fatty alkanes. However, the native yeast strains cannot produce fatty acids and fatty acid-derived biofuels in large quantities. To this end, we have summarized recent publications in this review on metabolic engineering of yeast strains to improve the production of fatty acid-derived biofuels, identified the bottlenecks that limit the productivity of biofuels, and categorized the appropriate approaches to overcome these obstacles. PMID:26106371

  4. Metabolic engineering of yeast to produce fatty acid-derived biofuels: bottlenecks and solutions

    PubMed Central

    Sheng, Jiayuan; Feng, Xueyang

    2015-01-01

    Fatty acid-derived biofuels can be a better solution than bioethanol to replace petroleum fuel, since they have similar energy content and combustion properties as current transportation fuels. The environmentally friendly microbial fermentation process has been used to synthesize advanced biofuels from renewable feedstock. Due to their robustness as well as the high tolerance to fermentation inhibitors and phage contamination, yeast strains such as Saccharomyces cerevisiae and Yarrowia lipolytica have attracted tremendous attention in recent studies regarding the production of fatty acid-derived biofuels, including fatty acids, fatty acid ethyl esters, fatty alcohols, and fatty alkanes. However, the native yeast strains cannot produce fatty acids and fatty acid-derived biofuels in large quantities. To this end, we have summarized recent publications in this review on metabolic engineering of yeast strains to improve the production of fatty acid-derived biofuels, identified the bottlenecks that limit the productivity of biofuels, and categorized the appropriate approaches to overcome these obstacles. PMID:26106371

  5. Self-assembly of poly(o-methoxyaniline) hollow nanospheres from a polymeric acid solution

    NASA Astrophysics Data System (ADS)

    Sui, Jing; Zhang, Lijuan; Peng, Hui; Travas-Sejdic, Jadranka; Kilmartin, Paul A.

    2009-10-01

    Self-assembled poly(o-methoxyaniline) (POMA) hollow nanospheres were prepared in a solution of poly(methyl vinyl ether-alt-maleic acid) (PMVEA) by oxidative polymerization using ammonium persulfate as the oxidant. The weight ratio of PMVEA to o-methoxyaniline in the solution had a significant effect on the morphology of the poly(o-methoxyaniline) nanospheres as determined by scanning electron microscopy. The diameter of the hollow nanospheres decreased from 440 to 210 nm with an increase in the PMVEA concentration from 1% to 5%. Freeze-fracture transmission electron microscopy results showed the presence of spherical micelles composed of PMVEA/ o-methoxyaniline prior to polymerization, which also decreased in size as more PMVEA was added to the solution, and can act as soft templates for the formation of the hollow POMA nanospheres. The POMA/PMVEA hollow nanospheres were characterized by means of Fourier transform infrared, UV-visible, x-ray photoelectron spectroscopy, elemental analysis and conductivity measurements.

  6. Adsorption of methyl violet in aqueous solutions by poly(acrylamide-co-acrylic acid) hydrogels

    NASA Astrophysics Data System (ADS)

    Şolpan, D.; Duran, S.; Saraydin, D.; Güven, O.

    2003-02-01

    In this study, Acrylamide(AAm)/Acrylic Acid(AAc) monomer mixtures which contain different quantities of acrylic acid have been irradiated to form hydrogels with γ-radiation. Acrylamide/Acrylic Acid (AAm/AAc) monomer mixtures which contain 15%, 20%, 30% AAm and irradiated with 8.0 kGy were used for swelling and diffusion studies in water and solutions of methyl violet. Diffusions of water and methyl violet within the hydrogels were found to be non-Fickian in character. In experiments on the adsorption of methyl violet, Type-S adsorption was found. Poly(AAm-co-AAc) hydrogel adsorbed methyl violet, while poly(AAm) hydrogel did not adsorb any dye. (Δ H) Heat of adsorption, (Δ G) Free energy of adsorption, (Δ S) Entropy of adsorption were calculated. These results show that poly(AAm-co-AAc) hydrogels can be used as a sorbent for water pollutants such as dyes and treatment of these organic contaminants from wastewater.

  7. Modeling of NO{sub x} absorption into nitric acid solutions containing hydrogen peroxide

    SciTech Connect

    Thomas, D.; Vanderschuren, J.

    1997-08-01

    A mathematical model was developed for the isothermal absorption of nitrogen oxides into nitric acid solutions containing hydrogen peroxide. This model, based on the two-film theory of absorption with chemical reactions, includes diffusive transport and equilibrium between species in the gas phase and simultaneous absorption of the NO{sub x} components with fast irreversible reactions in the liquid phase. Kinetic parameters relative to the absorption of the different NO{sub x} species were determined at increasing acidities and for a low concentration of H{sub 2}O{sub 2} from test runs performed in a small packed column at 20 C and atmospheric pressure for various NO{sub x} partial pressures up to 500 Pa and the whole range of NO{sub x} oxidation ratios. Only the parameter relative to trivalent NO{sub x} was found to increase with the HNO{sub 3} molarity, the other ones remaining constant. Interpretation of the experimental results according to the model showed that the hydrolysis is the main controlling step for tetravalent nitrogen oxides and that among the trivalent components nitrous acid is likely to be a major transporting species.

  8. The adsorption of cationic dye from aqueous solution onto acid-activated andesite.

    PubMed

    Tsai, Wen-Tien; Hsu, Hsin-Chieh; Su, Ting-Yi; Lin, Keng-Yu; Lin, Chien-Ming; Dai, Tzong-Hung

    2007-08-25

    The adsorption of cationic dye (i.e., methylene blue) onto acid-activated andesite in aqueous solution was studied in a batch system with respect to its kinetics as a function of agitation speed, initial adsorbate concentration, pH, and adsorbent mass. It was found that the resulting acid-activated adsorbent possessed a mesoporous structure with BET surface areas at around 60m(2)/g. The surface characterization of acid-activated andesite was also performed using the zeta-potential measurements, indicating that the charge sign on the surface of the andesite should be negative in a wide pH range (i.e., 3-11). Furthermore, a simplified kinetic model, pseudo-second-order, was tested to investigate the adsorption behaviors of methylene blue onto the clay samples treated under different process conditions. It was found that the adsorption process could be well described with the model. The adsorption capacity parameter of the model obtained in the present work was significantly in line with the process parameters.

  9. Removal of boron from aqueous solution using magnetic carbon nanotube improved with tartaric acid.

    PubMed

    Zohdi, Nima; Mahdavi, Fariba; Abdullah, Luqman Chuah; Choong, Thomas Sy

    2014-01-06

    Boron removal capacity of multi-walled carbon nanotubes (MWCNTs) modified with tartaric acid was investigated in this study. Modification of MWCNTs with tartaric acid was confirmed by Boehm surface chemistry method and fourier transform infra-red (FT-IR) spectroscopy. Experiments were performed to determine the adsorption isotherm and adsorption thermodynamic parameters of boron adsorption on tartaric acid modified MWCNTs (TA-MWCNTs). The effect of variables including initial pH, dosage of adsorbent, contact time and temperature was investigated. Analysis of data showed that adsorption equilibrium could be better described by Freundlich isotherm and the maximum adsorption capacities obtained at the pH of 6.0 was 1.97 mg/g. The estimated thermodynamic values of free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) indicated a spontaneous and an endothermic process. Furthermore, the TA-MWCNTs was magnetized for separation of boron-contaminated adsorbent from aqueous solution by applying magnetic field. The results showed that magnetic TA-MWCNTs particles were separated effectively after adsorption from contaminated water.

  10. The adsorption of cationic dye from aqueous solution onto acid-activated andesite.

    PubMed

    Tsai, Wen-Tien; Hsu, Hsin-Chieh; Su, Ting-Yi; Lin, Keng-Yu; Lin, Chien-Ming; Dai, Tzong-Hung

    2007-08-25

    The adsorption of cationic dye (i.e., methylene blue) onto acid-activated andesite in aqueous solution was studied in a batch system with respect to its kinetics as a function of agitation speed, initial adsorbate concentration, pH, and adsorbent mass. It was found that the resulting acid-activated adsorbent possessed a mesoporous structure with BET surface areas at around 60m(2)/g. The surface characterization of acid-activated andesite was also performed using the zeta-potential measurements, indicating that the charge sign on the surface of the andesite should be negative in a wide pH range (i.e., 3-11). Furthermore, a simplified kinetic model, pseudo-second-order, was tested to investigate the adsorption behaviors of methylene blue onto the clay samples treated under different process conditions. It was found that the adsorption process could be well described with the model. The adsorption capacity parameter of the model obtained in the present work was significantly in line with the process parameters. PMID:17363150

  11. Removal of boron from aqueous solution using magnetic carbon nanotube improved with tartaric acid

    PubMed Central

    2014-01-01

    Boron removal capacity of multi-walled carbon nanotubes (MWCNTs) modified with tartaric acid was investigated in this study. Modification of MWCNTs with tartaric acid was confirmed by Boehm surface chemistry method and fourier transform infra-red (FT-IR) spectroscopy. Experiments were performed to determine the adsorption isotherm and adsorption thermodynamic parameters of boron adsorption on tartaric acid modified MWCNTs (TA-MWCNTs). The effect of variables including initial pH, dosage of adsorbent, contact time and temperature was investigated. Analysis of data showed that adsorption equilibrium could be better described by Freundlich isotherm and the maximum adsorption capacities obtained at the pH of 6.0 was 1.97 mg/g. The estimated thermodynamic values of free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) indicated a spontaneous and an endothermic process. Furthermore, the TA-MWCNTs was magnetized for separation of boron-contaminated adsorbent from aqueous solution by applying magnetic field. The results showed that magnetic TA-MWCNTs particles were separated effectively after adsorption from contaminated water. PMID:24393401

  12. Removal of Basic Violet 14 from aqueous solution using sulphuric acid activated materials.

    PubMed

    Suresh, S

    2016-01-01

    In this study the adsorption of Basic Violet, 14 from aqueous solution onto sulphuric acid activated materials prepared from Calophyllum inophyllum (CS) and Theobroma cacao (TS) shells were investigated. The experimental data were analysed by Langmuir, Freundlich and Temkin isotherm models. The results showed that CS has a superior adsorption capacity compared to the TS. The adsorption capacity was found to be 1416.43 mg/g for CS and 980.39 mg/g for TS. The kinetic data results at different concentrations were analysed using pseudo first-order and pseudo-second order model. Boyd plot indicates that the dye adsorption onto CS and TS is controlled by film diffusion. The adsorbents were characterised by scanning electron microscopy. The materials used in this study were economical waste products and hence can be an attractive alternative to costlier adsorbents for dye removal in industrial wastewater treatment processes. PMID:27330899

  13. Modification of chitosan with monomethyl fumaric acid in an ionic liquid solution.

    PubMed

    Wang, Zhaodong; Zheng, Liuchun; Li, Chuncheng; Zhang, Dong; Xiao, Yaonan; Guan, Guohu; Zhu, Wenxiang

    2015-03-01

    Antibacterial and antioxidant monomethyl fumaric acid (MFA) was selected to modify chitosan, using aqueous solution of an ionic liquid as a homogeneous and green reaction media. The chemical structures of resulting polymers were systematically characterized by (1)H NMR, diffusion ordered spectroscopy, solid (13)C NMR and wide-angle X-ray diffraction. The results show that two kinds of MFA modified chitosan materials with totally different chemical structures have been synthesized. One product was a MF-chitosan salt composed of chitosan cation and MFA anion, which was obtained with the mediation of 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) and N-hydroxysuccinimide. The other one synthesized with the mediation of EDC was a MF-chitosan amide in which MFA and chitosan are covalently attached. Solubility of chitosan has been improved, and MF-chitosan salt can be readily dissolved in water. The antioxidant activity has been enhanced with the introduction of MFA, irrespective of the chemical structure.

  14. Ultrafast formation of the benzoic acid triplet upon ultraviolet photolysis and its sequential photodissociation in solution

    SciTech Connect

    Yang Chunfan; Su Hongmei; Sun Xuezhong; George, Michael W.

    2012-05-28

    Time-resolved infrared (TR-IR) absorption spectroscopy in both the femtosecond and nanosecond time domain has been applied to examine the photolysis of benzoic acid in acetonitrile solution following either 267 nm or 193 nm excitation. By combining the ultrafast and nanosecond TR-IR measurements, both the excited states and the photofragments have been detected and key mechanistic insights were obtained. We show that the solvent interaction modifies the excited state relaxation pathways and thus the population dynamics, leading to different photolysis behavior in solution from that observed in the gas phase. Vibrational energy transfer to solvents dissipates excitation energy efficiently, suppressing the photodissociation and depopulating the excited S{sub 2} or S{sub 3} state molecules to the lowest T{sub 1} state with a rate of {approx}2.5 ps after a delayed onset of {approx}3.7 ps. Photolysis of benzoic acid using 267 nm excitation is dominated by the formation of the T{sub 1} excited state and no photofragments could be detected. The results from TR-IR experiments using higher energy of 193 nm indicate that photodissociation proceeds more rapidly than the vibrational energy transfer to solvents and C-C bond fission becomes the dominant relaxation pathway in these experiments as featured by the prominent observation of the COOH photofragments and negligible yield of the T{sub 1} excited state. The measured ultrafast formation of T{sub 1} excited state supports the existence of the surface intersections of S{sub 2}/S{sub 1}, S{sub 2}/T{sub 2}, and S{sub 1}/T{sub 1}/T{sub 2}, and the large T{sub 1} quantum yield of {approx}0.65 indicates the importance of the excited state depopulation to triplet manifold as the key factor affecting the photophysical and photochemical behavior of the monomeric benzoic acid.

  15. Ultrafast formation of the benzoic acid triplet upon ultraviolet photolysis and its sequential photodissociation in solution

    NASA Astrophysics Data System (ADS)

    Yang, Chunfan; Su, Hongmei; Sun, Xuezhong; George, Michael W.

    2012-05-01

    Time-resolved infrared (TR-IR) absorption spectroscopy in both the femtosecond and nanosecond time domain has been applied to examine the photolysis of benzoic acid in acetonitrile solution following either 267 nm or 193 nm excitation. By combining the ultrafast and nanosecond TR-IR measurements, both the excited states and the photofragments have been detected and key mechanistic insights were obtained. We show that the solvent interaction modifies the excited state relaxation pathways and thus the population dynamics, leading to different photolysis behavior in solution from that observed in the gas phase. Vibrational energy transfer to solvents dissipates excitation energy efficiently, suppressing the photodissociation and depopulating the excited S2 or S3 state molecules to the lowest T1 state with a rate of ˜2.5 ps after a delayed onset of ˜3.7 ps. Photolysis of benzoic acid using 267 nm excitation is dominated by the formation of the T1 excited state and no photofragments could be detected. The results from TR-IR experiments using higher energy of 193 nm indicate that photodissociation proceeds more rapidly than the vibrational energy transfer to solvents and C-C bond fission becomes the dominant relaxation pathway in these experiments as featured by the prominent observation of the COOH photofragments and negligible yield of the T1 excited state. The measured ultrafast formation of T1 excited state supports the existence of the surface intersections of S2/S1, S2/T2, and S1/T1/T2, and the large T1 quantum yield of ˜0.65 indicates the importance of the excited state depopulation to triplet manifold as the key factor affecting the photophysical and photochemical behavior of the monomeric benzoic acid.

  16. Extraction of palladium from acidic solutions with the use of carbon adsorbents

    SciTech Connect

    O.N. Kononova; N.G. Goryaeva; N.B. Dostovalova; S.V. Kachin; A.G. Kholmogorov

    2007-08-15

    We studied the sorption of palladium(II) on LKAU-4, LKAU-7, and BAU carbon adsorbents from model hydrochloric acid solutions and the solutions of spent palladium-containing catalysts. It was found that sorbents based on charcoal (BAU) and anthracite (LKAU-4) were characterized by high sorption capacities for palladium. The kinetics of the saturation of carbon adsorbents with palladium(II) ions was studied, and it was found that more than 60% of the initial amount of Pd(II) was recovered in a 1-h contact of an adsorbent with a model solution. This value for the solutions of spent catalysts was higher than 35%.

  17. Separation of thorium and uranium in nitric acid solution using silica based anion exchange resin.

    PubMed

    Chen, Yanliang; Wei, Yuezhou; He, Linfeng; Tang, Fangdong

    2016-09-30

    To separate thorium and uranium in nitric acid solution using anion exchange process, a strong base silica-based anion exchange resin (SiPyR-N4) was synthesized. Batch experiments were conducted and the separation factor of thorium and uranium in 9M nitric acid was about 10. Ion exchange chromatography was applied to separate thorium and uranium in different ratios. Uranium could be eluted by 9M nitric acid and thorium was eluted by 0.1M nitric acid. It was proved that thorium and uranium can be separated and recovered successfully by this method.

  18. Comparison of XAD macroporous resins for the concentration of fulvic acid from aqueous solution

    USGS Publications Warehouse

    Aiken, G.R.

    1979-01-01

    Five macroreticular, nonlonlc AmberlHe XAD resins were evaluated for concentration and Isolation of fulvlc acid from aqueous solution. The capacity of each resin for fulvlc acid was measured by both batch and column techniques. Elution efficiencies were determined by desorptlon with 0.1 N NaOH. Highest recoveries were obtained with the acrylic ester resins which proved to be most efficient for both adsorption and elution of fulvlc acid. Compared to the acrylic ester resins, usefulness of the styrene dvlnybenzene resins to remove fulvlc acid is limited because of slow diffusion-controlled adsorption and formation of charge-transfer complexes, which hinders elution. ?? 1979 American Chemical Society.

  19. Separation of thorium and uranium in nitric acid solution using silica based anion exchange resin.

    PubMed

    Chen, Yanliang; Wei, Yuezhou; He, Linfeng; Tang, Fangdong

    2016-09-30

    To separate thorium and uranium in nitric acid solution using anion exchange process, a strong base silica-based anion exchange resin (SiPyR-N4) was synthesized. Batch experiments were conducted and the separation factor of thorium and uranium in 9M nitric acid was about 10. Ion exchange chromatography was applied to separate thorium and uranium in different ratios. Uranium could be eluted by 9M nitric acid and thorium was eluted by 0.1M nitric acid. It was proved that thorium and uranium can be separated and recovered successfully by this method. PMID:27614730

  20. Boric acid solution concentration influencing p-type emitter formation in n-type crystalline Si solar cells

    NASA Astrophysics Data System (ADS)

    Singha, Bandana; Singh Solanki, Chetan

    2016-09-01

    Boric acid (BA) is a spin on dopant (BSoD) source which is used to form p+ emitters in n-type c-Si solar cells. High purity boric acid powder (99.99% pure) when mixed with deionized (DI) water can result in high quality p-type emitter with less amount of surface defects. In this work, we have used different concentrations of boric acid solution concentrations to fabricate p-type emitters with sheet resistance values < 90 Ω/□. The corresponding junction depths for the same are less than 500 nm as measured by SIMS analysis. Boron rich layer (BRL), which is considered as detrimental in emitter performance is found to be minimal for BA solution concentration less than 2% and hence useful for p-type emitter formation.

  1. Organic Acids Over Equatorial Africa: Results from DECAFE 88

    NASA Astrophysics Data System (ADS)

    Helas, Günter; Bingemer, Heinz; Andreae, Meinrat O.

    1992-04-01

    Gaseous short chain organic acids were measured during the dry season (February) in and above the rain forest of the northern Congo. Samples were taken at ground level and during several flights up to 4 km altitude. The organic acids were concentrated from the atmosphere by using "mist scrubbers," which expose a mist of deionized water to the air to be probed. The organic acids absorbed in the water were subsequently analyzed by ion chromatography. Formic, acetic, and pyruvic acids were identified in the samples. At ground level, average mixing ratios of gaseous formic and acetic acid of 0.5±0.6 and 0.6±0.7 parts per billion by volume (ppbv) (1 s), respectively, were found. Boundary layer mixing ratios, however, were significantly higher (3.7±1.0 and 2.7±0.9 ppbv). This indicates a downward net flux of these atmospheric trace components from the boundary layer to the surface. Free tropospheric samples taken above the cloud convection layer show lower mixing ratios again (0.9±0.3 and 0.7±0.1 ppbv). On the basis of this vertical distribution, direct emission by vegetation is not considered to be the dominant source. Biomass burning and photochemical oxidation of biogenic precursors are the major processes contributing to the enhancement of organic acids observed in the boundary layer. The organic acids parallel the profiles of ozone and CO, which suggests that their generation processes are closely related. Pyruvic acid is not correlated with formic acid, indicating that the oxidation of isoprene is not of major importance. In emissions from biomass fires, CO correlates well with formic and acetic acid, and thus some of the enhancement of organic acids in the boundary layer can be explained due to burning. However, an additional gas phase source for organic acids must exist to explain the observed ratio of formic to acetic acid. This is most likely the ozonolysis of olefins which were released as pyrolysis products from biomass burning.

  2. Bis(mesitoyl)phosphinic acid: photo-triggered release of metaphosphorous acid in solution.

    PubMed

    Fast, David E; Zalibera, Michal; Lauer, Andrea; Eibel, Anna; Schweigert, Caroline; Kelterer, Anne-Marie; Spichty, Martin; Neshchadin, Dmytro; Voll, Dominik; Ernst, Hanna; Liang, Yu; Dietliker, Kurt; Unterreiner, Andreas-Neil; Barner-Kowollik, Christopher; Grützmacher, Hansjörg; Gescheidt, Georg

    2016-08-01

    Bis(mesitoyl)phosphinic acid and its sodium salt display a unique photo-induced reactivity: both derivatives stepwise release two mesitoyl radicals and, remarkably, metaphosphorous acid (previously postulated as transient species in the gas phase), providing a new phosphorus-based reagent. PMID:27431207

  3. Emissions involved in acidic deposition processes: Methodology and results

    SciTech Connect

    Placet, M.

    1990-01-01

    Data on the emissions involved in atmospheric acid-base chemistry are crucial to the assessment of acidic deposition and its effects. Sulfur dioxide (SO{sub 2}), nitrogen oxides (NO{sub x}), and volatile organic compounds (VOCs) are the primary chemical compounds involved in acidic deposition processes. In addition, other emission species -- e.g., ammonia, alkaline dust particles, hydrogen chloride, and hydrogen fluoride -- are involved in atmospheric acid-base chemistry, either by contributing acidic constituents or by neutralizing acidic species. Several emissions data bases have been developed under the auspices of the National Acid Precipitation Program (NAPAP). In addition to those developed by NAPAP, emissions data bases and emissions trends estimates also have been developed by organizations such as the Electric Power Research Institute (EPRI) and the U.S. Environmental Protection Agency (EPA). This paper briefly describes and compares the methods used in developing these emissions data bases and presents an overview of their emissions estimates. A more detailed discussion of these topics can be found in the State-of-Science Report on emissions recently released by NAPAP and in the references cited in that report. 14 refs., 4 figs., 1 tab.

  4. Extraction of gallium(III) from hydrochloric acid solutions by trioctylammonium-based mixed ionic liquids.

    PubMed

    Katsuta, Shoichi; Okai, Miho; Yoshimoto, Yuki; Kudo, Yoshihiro

    2012-01-01

    The extractabilities of aluminium(III), gallium(III), and indium(III) from hydrochloric acid solutions were investigated using a mixture of two protic ionic liquids, trioctylammonium bis(trifluoromethanesulfonyl)amide ([TOAH][NTf(2)]) and trioctylammonium nitrate ([TOAH][NO(3)]). At a HCl concentration of 4 mol L(-1) or more, gallium(III) was nearly quantitatively extracted and the extractability order was Ga > Al > In. The extractability of gallium(III) increased with increasing [TOAH][NO(3)] content in the mixed ionic liquid. The extracted gallium(III) was quantitatively stripped with aqueous nitric acid solutions. The separation and recovery of gallium(III) from hydrochloric acid solutions containing excess indium(III) was demonstrated using the mixed ionic liquid.

  5. Effect of Mineral Admixtures on Resistance to Sulfuric Acid Solution of Mortars with Quaternary Binders

    NASA Astrophysics Data System (ADS)

    Makhloufi, Zoubir; Bederina, Madani; Bouhicha, Mohamed; Kadri, El-Hadj

    This research consists to study the synergistic action of three mineral additions simultaneously added to the cement. This synergistic effect has a positive effect on the sustainability of limestone mortars. Tests were performed on mortars based on crushed limestone sand and manufactured by five quaternary binders (ordinary Portland cement and CPO mixed simultaneously with filler limestone, blast-furnace and natural pozzolan). The purpose of this research was to identify the resistance of five different mortars to the solution of sulfuric acid. Changes in weight loss and compressive strength measured at 30, 60, 90, 120 and 180 days for each acid solution were studied. We followed up on the change in pH of the sulfuric acid solution at the end of each month up to 180 days.

  6. Novel Regenerated Solvent Extraction Processes for the Recovery of Carboxylic Acids or Ammonia from Aqueous Solutions Part II. Recovery of Ammonia from Sour Waters

    SciTech Connect

    Poole, L.J.; King, C.J.

    1990-03-01

    Two novel regenerated solvent extraction processes are examined. The first process has the potential to reduce the energy costs inherent in the recovery of low-volatility carboxylic acids from dilute aqueous solutions. The second process has the potential for reducing the energy costs required for separate recovery of ammonia and acid gases (e.g. CO{sub 2} and H{sub 2}S) from industrial sour waters. The recovery of carboxylic acids from dilute aqueous solution can be achieved by extraction with tertiary amines. An approach for regeneration and product recovery from such extracts is to back-extract the carboxylic acid with a water-soluble, volatile tertiary amine, such as trimethylamine. The resulting trimethylammonium carboxylate solution can be concentrated and thermally decomposed, yielding the product acid and the volatile amine for recycle. Experimental work was performed with lactic acid, SUCCiOlC acid, and fumaric acid. Equilibrium data show near-stoichiometric recovery of the carboxylic acids from an organic solution of Alamine 336 into aqueous solutions of trimethylamine. For fumaric and succinic acids, partial evaporation of the aqueous back extract decomposes the carboxylate and yields the acid product in crystalline form. The decomposition of aqueous solutions of trimethylammonium lactates was not carried out to completion, due to the high water solubility of lactic acid and the tendency of the acid to self-associate. The separate recovery of ammonia and acid gases from sour waters can be achieved by combining steam-stripping of the acid gases with simultaneous removal of ammonia by extraction with a liquid cation exchanger. The use of di-2,4,4-trimethylpentyl phosphinic acid as the liquid cation exchanger is explored in this work. Batch extraction experiments were carried out to measure the equilibrium distribution ratio of ammonia between an aqueous buffer solution and an organic solution of the phosphinic acid (0.2N) in Norpar 12. The concentration

  7. Gamma-irradiation of malic acid in aqueous solutions. [prebiotic significance

    NASA Technical Reports Server (NTRS)

    Negron-Mendoza, A.; Graff, R. L.; Ponnamperuma, C.

    1980-01-01

    The gamma-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the nonvolatile products. Thin layer chromatography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the gamma-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

  8. Thermal transformation of trans-5-O-caffeoylquinic acid (trans-5-CQA) in alcoholic solutions.

    PubMed

    Dawidowicz, Andrzej L; Typek, Rafal

    2015-01-15

    Chlorogenic acid (CQA), the ester of caffeic acid with quinic acid supplied to human organisms mainly with coffee, tea, fruit and vegetables, has been one of the most studied polyphenols. It is potentially useful in pharmaceuticals, food additives, and cosmetics due to its recently discovered biomedical activity, which revived interest in its properties, isomers and natural occurrence. We found that the heating of the alcoholic solution of trans-5-O-caffeoylquinic acid produced at least twenty compounds (chlorogenic acid derivatives and its reaction products with water and alcohol). The formation of three of them (methoxy, ethoxy and propoxy adducts) has not been reported yet. No reports exist either on methoxy adducts of 3- and 4-O-caffeoylquinic acid appearing in buffered methanol/water mixtures at pH exceeding 7. We observed that the amount of each formed component depended on the heating time, type of alcohol, its concentration in alcoholic/water mixture, and pH.

  9. PHYSICAL SOLUTIONS FOR ACID MINE DRAINAGE AT REMOTE MINE SITES

    EPA Science Inventory

    After completing extensive bench-scale testing to determine optimum treatment approaches, the technology has been taken to the field. Preliminary results show that calcium hydroxide precipitates the bulk of the arsenic and zinc; the granular ferric hydroxide removes the rest of ...

  10. Uranium fate in Hanford sediment altered by simulated acid waste solutions

    DOE PAGES

    Gartman, Brandy N.; Qafoku, Nikolla P.; Szecsody, James E.; Kukkadapu, Ravi K.; Wang, Zheming; Wellman, Dawn M.; Truex, Michael J.

    2015-07-31

    Many aspects of U(VI) behavior in sediments that are previously exposed to acidic waste fluids for sufficiently long times to induce significant changes in pH and other physical, mineralogical and chemical properties, are not well documented in the literature. For this reason, we conducted a series of macroscopic batch experiments combined with a variety of bulk characterization studies (Mössbauer and laser spectroscopy), micro-scale inspections (µ-XRF), and molecular scale interrogations (XANES) with the objectives to: i) determine the extent of U(VI) partitioning to Hanford sediments previously exposed to acidic waste simulants (pH = 2 and pH = 5) and under neutralmore » conditions (pH = 8) at varying background solution concentrations (i.e., NaNO3); ii) determine micron-scale solid phase associated U valence state and phase identity; and iii) provide information for a plausible conceptual model of U(VI) attenuation under waste plume acidic conditions. The results of the batch experiments showed that the acid pre-treated sediment had high affinity for aqueous U(VI), which was removed from solution via two pH dependent and apparently different mechanisms (adsorption at pH = 2 and precipitation at pH = 5). The micro-scale inspections and XANES analyses confirmed that high concentration areas were rich mainly in U(VI), demonstrating that most of the added U(VI) was not reduced to U(IV). The laser spectroscopy data showed that uranyl phosphates {e.g. metaautunite [Ca(UO2)2(PO4)2•10-12H2O] and phosphuranylite [KCa(H3O)3(UO2)7(PO4)4O4•8(H2O)]} were present in the sediments. They also showed clear differences between the U bearing phases in the experiments conducted in the presence or absence of air. As a result, the data generated from these experiments will help in a better understanding of the reactions and processes that have a significant effect and/or control U mobility.« less

  11. Uranium fate in Hanford sediment altered by simulated acid waste solutions

    SciTech Connect

    Gartman, Brandy N.; Qafoku, Nikolla P.; Szecsody, James E.; Kukkadapu, Ravi K.; Wang, Zheming; Wellman, Dawn M.; Truex, Michael J.

    2015-07-31

    Many aspects of U(VI) behavior in sediments that are previously exposed to acidic waste fluids for sufficiently long times to induce significant changes in pH and other physical, mineralogical and chemical properties, are not well documented in the literature. For this reason, we conducted a series of macroscopic batch experiments combined with a variety of bulk characterization studies (Mössbauer and laser spectroscopy), micro-scale inspections (µ-XRF), and molecular scale interrogations (XANES) with the objectives to: i) determine the extent of U(VI) partitioning to Hanford sediments previously exposed to acidic waste simulants (pH = 2 and pH = 5) and under neutral conditions (pH = 8) at varying background solution concentrations (i.e., NaNO3); ii) determine micron-scale solid phase associated U valence state and phase identity; and iii) provide information for a plausible conceptual model of U(VI) attenuation under waste plume acidic conditions. The results of the batch experiments showed that the acid pre-treated sediment had high affinity for aqueous U(VI), which was removed from solution via two pH dependent and apparently different mechanisms (adsorption at pH = 2 and precipitation at pH = 5). The micro-scale inspections and XANES analyses confirmed that high concentration areas were rich mainly in U(VI), demonstrating that most of the added U(VI) was not reduced to U(IV). The laser spectroscopy data showed that uranyl phosphates {e.g. metaautunite [Ca(UO2)2(PO4)2•10-12H2O] and phosphuranylite [KCa(H3O)3(UO2)7(PO4)4O4•8(H2O)]} were present in the sediments. They also showed clear differences between the U bearing phases in the experiments conducted in the presence or absence of air. As a result, the data generated from these experiments will help in a better understanding of the reactions and

  12. The aqueous photolysis of α-pinene in solution with humic acid

    USGS Publications Warehouse

    Goldberg, Marvin C.; Cunningham, Kirkwood M.; Aiken, George R.; Weiner, Eugene R.; ,

    1992-01-01

    Terpenes are produced abundantly by environmental processes but are found in very low concentrations in natural waters. Aqueous photolysis of solutions containing α-pinene, a representative terpene, in the presence of humic acid resulted in degradation of the pinene. Comparison of this reaction to photolysis of α-pinene in the presence of methylene blue leads to the conclusion that the reactive pathway for the abiotic degradation of α-pinene is due to reaction with singlet oxygen produced by irradiation of the humic material. The initial product of single oxygen and α-pinene is a hydroperoxide. Since humic materials are prevalent in most natural waters, this mechanism of photodecomposition for α-pinene probably also applies to other terpenes in surface waters and may be reasonably considered to contribute to their low environmental concentration.

  13. A free energy analysis of nucleic acid base stacking in aqueous solution.

    PubMed Central

    Friedman, R A; Honig, B

    1995-01-01

    This paper reports a theoretical study of the free energy contributions to nucleic acid base stacking in aqueous solution. Electrostatic interactions are treated by using the finite difference Poisson-Boltzmann method and nonpolar effects are treated with explicit calculation of van der Waals interactions and/or free energy-surface area relationships. Although for some pairs of bases there is a favorable Coulombic interaction in the stacked conformation, generally the net effect of electrostatic interactions is to oppose stacking. This result is caused by the loss of favorable base-solvent electrostatic interactions, that accompany the partial removal of polar atoms from water in the stacked conformation. Nonpolar interactions, involving the hydrophobic effect and enhancement of van der Waals interactions caused by close-packing, drive stacking. The calculations qualitatively reproduce the experimental dependence of stacking free energy on purine-pyrimidine composition. Images FIGURE 1 PMID:8534823

  14. Standard enthalpies of formation of α-aminobutyric acid and products of its dissociation in an aqueous solution

    NASA Astrophysics Data System (ADS)

    Lytkin, A. I.; Chernikov, V. V.; Krutova, O. N.

    2016-08-01

    Heats of solution of crystalline α-aminobutyric acid in water and in aqueous solutions of potassium hydroxide at 298.15 K are measured by means of direct calorimetry. Standard enthalpies of formation of the amino acid and products of its dissociation in an aqueous solution are calculated.

  15. Chemical modification of amino acids by atmospheric-pressure cold plasma in aqueous solution

    NASA Astrophysics Data System (ADS)

    Takai, Eisuke; Kitamura, Tsuyoshi; Kuwabara, Junpei; Ikawa, Satoshi; Yoshizawa, Shunsuke; Shiraki, Kentaro; Kawasaki, Hideya; Arakawa, Ryuichi; Kitano, Katsuhisa

    2014-07-01

    Plasma medicine is an attractive new research area, but the principles of plasma modification of biomolecules in aqueous solution remain elusive. In this study, we investigated the chemical effects of atmospheric-pressure cold plasma on 20 naturally occurring amino acids in aqueous solution. High-resolution mass spectrometry revealed that chemical modifications of 14 amino acids were observed after plasma treatment: (i) hydroxylation and nitration of aromatic rings in tyrosine, phenylalanine and tryptophan; (ii) sulfonation and disulfide linkage formation of thiol groups in cysteine; (iii) sulfoxidation of methionine and (iv) amidation and ring-opening of five-membered rings in histidine and proline. A competitive reaction experiment using 20 amino acids demonstrated that sulfur-containing and aromatic amino acids were preferentially decreased by the plasma treatment. These data provide fundamental information for elucidating the mechanism of protein inactivation for biomedical plasma applications.

  16. Phase equilibria in a system of aqueous arginine with an octane solution of sulfonic acid

    NASA Astrophysics Data System (ADS)

    Kuvaeva, Z. I.; Koval'chuk, I. V.; Vodop'yanova, L. A.; Soldatov, V. S.

    2013-05-01

    The extraction of arginine (Arg) from aqueous salt (0.1 M NaCl) solutions with a sulfo extractant in a wide range of pH values and amino acid concentrations was studied. The 0.1 M solution of dinonylnaphthalenesulfonic acid (HD) in octane was used as an extractant. The degree of extraction was found to be high at pH 0.8-9.0. This can be explained by the effect of additional intermolecular interactions in the extractant phase involving the guanidine group of Arg.

  17. Stability of antimicrobial activity of peracetic acid solutions used in the final disinfection process.

    PubMed

    Costa, Solange Alves da Silva; Paula, Olívia Ferreira Pereira de; Silva, Célia Regina Gonçalves E; Leão, Mariella Vieira Pereira; Santos, Silvana Soléo Ferreira dos

    2015-01-01

    The instruments and materials used in health establishments are frequently exposed to microorganism contamination, and chemical products are used before sterilization to reduce occupational infection. We evaluated the antimicrobial effectiveness, physical stability, and corrosiveness of two commercial formulations of peracetic acid on experimentally contaminated specimens. Stainless steel specimens were contaminated with Staphylococcus aureus, Escherichia coli, Candida albicans, blood, and saliva and then immersed in a ready peracetic acid solution: 2% Sekusept Aktiv (SA) or 0.25% Proxitane Alpha (PA), for different times. Then, washes of these instruments were plated in culture medium and colony-forming units counted. This procedure was repeated six times per day over 24 non-consecutive days. The corrosion capacity was assessed with the mass loss test, and the concentration of peracetic acid and pH of the solutions were measured with indicator tapes. Both SA and PA significantly eliminated microorganisms; however, the SA solution was stable for only 4 days, whereas PA remained stable throughout the experiment. The concentration of peracetic acid in the SA solutions decreased over time until the chemical was undetectable, although the pH remained at 5. The PA solution had a concentration of 500-400 mg/L and a pH of 2-3. Neither formulation induced corrosion and both reduced the number of microorganisms (p = 0.0001). However, the differences observed in the performance of each product highlight the necessity of establishing a protocol for optimizing the use of each one.

  18. Stability of antimicrobial activity of peracetic acid solutions used in the final disinfection process.

    PubMed

    Costa, Solange Alves da Silva; Paula, Olívia Ferreira Pereira de; Silva, Célia Regina Gonçalves E; Leão, Mariella Vieira Pereira; Santos, Silvana Soléo Ferreira dos

    2015-01-01

    The instruments and materials used in health establishments are frequently exposed to microorganism contamination, and chemical products are used before sterilization to reduce occupational infection. We evaluated the antimicrobial effectiveness, physical stability, and corrosiveness of two commercial formulations of peracetic acid on experimentally contaminated specimens. Stainless steel specimens were contaminated with Staphylococcus aureus, Escherichia coli, Candida albicans, blood, and saliva and then immersed in a ready peracetic acid solution: 2% Sekusept Aktiv (SA) or 0.25% Proxitane Alpha (PA), for different times. Then, washes of these instruments were plated in culture medium and colony-forming units counted. This procedure was repeated six times per day over 24 non-consecutive days. The corrosion capacity was assessed with the mass loss test, and the concentration of peracetic acid and pH of the solutions were measured with indicator tapes. Both SA and PA significantly eliminated microorganisms; however, the SA solution was stable for only 4 days, whereas PA remained stable throughout the experiment. The concentration of peracetic acid in the SA solutions decreased over time until the chemical was undetectable, although the pH remained at 5. The PA solution had a concentration of 500-400 mg/L and a pH of 2-3. Neither formulation induced corrosion and both reduced the number of microorganisms (p = 0.0001). However, the differences observed in the performance of each product highlight the necessity of establishing a protocol for optimizing the use of each one. PMID:25715037

  19. Recovery of water and acid from leach solutions using direct contact membrane distillation.

    PubMed

    Kesieme, Uchenna K; Milne, Nicholas; Cheng, Chu Yong; Aral, Hal; Duke, Mikel

    2014-01-01

    This paper describes for the first time the use of direct contact membrane distillation (DCMD) for acid and water recovery from a real leach solution generated by a hydrometallurgical plant. The leach solutions considered contained H2SO4 or HCl. In all tests the temperature of the feed solution was kept at 60 °C. The test work showed that fluxes were within the range of 18-33 kg/m(2)/h and 15-35 kg/m(2)/h for the H2SO4 and HCl systems, respectively. In the H2SO4 leach system, the final concentration of free acid in the sample solution increased on the concentrate side of the DCMD system from 1.04 M up to 4.60 M. The sulfate separation efficiency was over 99.9% and overall water recovery exceeded 80%. In the HCl leach system, HCl vapour passed through the membrane from the feed side to the permeate. The concentration of HCl captured in the permeate was about 1.10 M leaving behind only 0.41 M in the feed from the initial concentration of 2.13 M. In all the experiments, salt rejection was >99.9%. DCMD is clearly viable for high recovery of high quality water and concentrated H2SO4 from spent sulfuric acid leach solution where solvent extraction could then be applied to recover the sulfuric acid and metals. While HCl can be recovered for reuse using only DCMD.

  20. Effect of hydrochloric acid on sound absorption and relaxation frequency in magnesium sulfate solutions

    NASA Astrophysics Data System (ADS)

    Fisher, F. H.

    2002-05-01

    The epic work of Kurtze and Tamm on sound absorption spectroscopy in divalent sulfate electrolyte solutions (1953) from the low-kHz region up to over 200 MHz revealed astonishing variability at frequencies below 10 MHz and a common relaxation frequency at about 200 MHz. For magnesium sulfate [Epsom salts] solutions, the salt producing 30× the absorption of fresh water below the 100-kHz region in the oceans at low concentrations [~0.02 moles/liter], Kurtze and Tamm investigated the effects of adding HC1 or H2SO4. They found that as formal pH increased, the results were different for these acids in reducing the sound absorption. Fisher (1983) found that if the absorption was plotted against free hydrogen, ion concentration was the same. We used the 100-liter titanium sphere, a spare ballast tank from the WHOI submarine ALVIN. With precise temperature control, we found an increase in the relaxation frequency as HC1 was added in conjunction with the reduction in sound absorption. The results will be presented and an explanation will be proposed in the context of the Eigen and Tamm multistate dissociation model for MgSO4 (1962) which explains the effects of pressure on both absorption and conductance. [Work supported by ONR.] The author acknowledges C. C. Hsu for his work on this project.

  1. Prevention of postoperative pericardial adhesions with a hyaluronic acid coating solution. Experimental safety and efficacy studies.

    PubMed

    Mitchell, J D; Lee, R; Hodakowski, G T; Neya, K; Harringer, W; Valeri, C R; Vlahakes, G J

    1994-06-01

    Postoperative pericardial adhesions complicate reoperative cardiac procedures. Topical application of solutions containing hyaluronic acid have been shown to reduce adhesions after abdominal and orthopedic surgery. The mechanism by which hyaluronic acid solutions prevent adhesion formation is unknown but may be due to a cytoprotective effect on mesothelial surfaces, which would limit intraoperative injury. In this study, we tested the efficacy and safety of hyaluronic acid coating solutions for the prevention of postoperative intrapericardial adhesion formation. Eighteen mongrel dogs underwent median sternotomy and pericardiotomy followed by a standardized 2-hour protocol of forced warm air desiccation and abrasion of the pericardial and epicardial surfaces. Group 1 (n = 6) served as untreated control animals. Group 2 (n = 6) received topical administration of 0.4% hyaluronic acid in phosphate-buffered saline solution at the time of pericardiotomy, at 20-minute intervals during the desiccation/abrasion protocol, and at pericardial closure. The total test dose was less than 1% of the circulating blood volume. Group 3 (n = 6) served as a vehicle control, receiving phosphate-buffered saline solution as a topical agent in a fashion identical to that used in group 2. At resternotomy 8 weeks after the initial operation, the intrapericardial adhesions were graded on a 0 to 4 severity scale at seven different areas covering the ventricular, atrial, and great vessel surfaces. In both the untreated control (group 1, mean score 3.2 +/- 0.4) and vehicle control (group 3, mean score 3.3 +/- 0.2) animals, dense adhesions were encountered. In contrast, animals treated with the hyaluronic acid solution (group 2, mean score 0.8 +/- 0.3) characteristically had no adhesions or filmy, transparent adhesions graded significantly less severe than either the untreated control (group 2 versus group 1, p < 0.001) or vehicle control (group 2 versus group 3, p < 0.001) animals. In separate

  2. Dispersion-free solvent extraction of Cr(VI) from acidic solutions using hollow fiber contactor.

    PubMed

    Alguacil, Francisco J; Alonso, Manuel; Lopez, Félix A; Lopez-Delgado, Aurora; Padilla, Isabel

    2009-10-15

    The use of dispersión-free solvent extraction, through microporous hydrophobic membrane has been investigated. The hollow fiber contactor, with surface area of 1.4 m2 was used to extract Cr(VI) (0.005-0.12 g/L from aqueous sulphuric acidic media (pH 2.5-4.2 +/- 0.05). Several parameters such as extractant concentration, feed acidity and metal concentration in the initial aqueous solution were investigated. Results revealed that 15% v/v Cyanex 923 in Exxsol D-100 as organic phase and feed in the 2.5 pH range, gave optimum extraction (exceeding 95%) of Cr(VI) and it was possible to strip using 10 g/L hydrazine sulfate (also with recoveries exceeding 95%). In this step, Cr(VI) is immediately reduced to the less hazardous Cr(III) state. Results also showed that under the various experimental conditions, chromium(VI) extraction was rate-controlled by the interfacial reaction on the membrane surface. Typical overall mass transfer coefficients values are 4.2 x 10(-5) and 3.6 x 10(-6) cm/s for extraction and stripping operations, respectively.

  3. Simultaneous pollutant removal and electricity generation in denitrifying microbial fuel cell with boric acid-borate buffer solution.

    PubMed

    Chen, Gang; Zhang, Shaohui; Li, Meng; Wei, Yan

    2015-01-01

    A double-chamber denitrifying microbial fuel cell (MFC), using boric acid-borate buffer solution as an alternative to phosphate buffer solution, was set up to investigate the influence of buffer solution concentration, temperature and external resistance on electricity generation and pollutant removal efficiency. The result revealed that the denitrifying MFC with boric acid-borate buffer solution was successfully started up in 51 days, with a stable cell voltage of 205.1 ± 1.96 mV at an external resistance of 50 Ω. Higher concentration of buffer solution favored nitrogen removal and electricity generation. The maximum power density of 8.27 W/m(3) net cathodic chamber was obtained at a buffer solution concentration of 100 mmol/L. An increase in temperature benefitted electricity generation and nitrogen removal. A suitable temperature for this denitrifying MFC was suggested to be 25 °C. Decreasing the external resistance favored nitrogen removal and organic matter consumption by exoelectrogens. PMID:25768227

  4. Simultaneous pollutant removal and electricity generation in denitrifying microbial fuel cell with boric acid-borate buffer solution.

    PubMed

    Chen, Gang; Zhang, Shaohui; Li, Meng; Wei, Yan

    2015-01-01

    A double-chamber denitrifying microbial fuel cell (MFC), using boric acid-borate buffer solution as an alternative to phosphate buffer solution, was set up to investigate the influence of buffer solution concentration, temperature and external resistance on electricity generation and pollutant removal efficiency. The result revealed that the denitrifying MFC with boric acid-borate buffer solution was successfully started up in 51 days, with a stable cell voltage of 205.1 ± 1.96 mV at an external resistance of 50 Ω. Higher concentration of buffer solution favored nitrogen removal and electricity generation. The maximum power density of 8.27 W/m(3) net cathodic chamber was obtained at a buffer solution concentration of 100 mmol/L. An increase in temperature benefitted electricity generation and nitrogen removal. A suitable temperature for this denitrifying MFC was suggested to be 25 °C. Decreasing the external resistance favored nitrogen removal and organic matter consumption by exoelectrogens.

  5. New crystallization of fatty acids from aqueous ethanol solution combined with liquid-liquid extraction

    SciTech Connect

    Maeda, Kouji; Nomura, Yoshihisa; Tai, Kimihiko; Ueno, Yoshitaka; Fukui, Keisuke; Hirota, Syouji

    1999-06-01

    A new separation process of saturated fatty acids (lauric acid-myristic acid) using crystallization from an aqueous ethanol solution has been examined. There were two vessels in this separation process: an extraction vessel and a crystallization vessel. The fatty acids in the aqueous phase were first extracted from their organic phase (melt) in the extraction vessel. The fatty acids in the aqueous phase were continuously introduced to the crystallization vessel, and then the fatty acids were crystallized there. The crystals of the fatty acids were collected continuously above the aqueous phase in the crystallization vessel. In this process, the yield and the purity of the crystals over time were measured, and it was found that the purity of lauric acid increased unsteadily up to 0.98 mole fraction of lauric acid with an increase in the yield of the low yield range. The mole fraction of ethanol in the aqueous phase could be significant to control the relationship between the yield and the purity of the crystals. Three different mole fractions of lauric acid in the organic phase were used to be separated in this process. Moreover, the authors have considered the effective separations of this process, and the maximum yield and purity of the crystals have been estimated by a simple mass balance.

  6. Electrochemical formation of hydroxide for enhancing carbon dioxide and acid gas uptake by a solution

    DOEpatents

    Rau, Gregory Hudson

    2012-05-15

    A system is described for forming metal hydroxide from a metal carbonate utilizing a water electrolysis cell having an acid-producing anode and a hydroxyl-producing cathode immersed in a water solution of sufficient ionic content to allow an electric current to pass between the hydroxyl-producing cathode and the acid-producing anode. A metal carbonate, in particular water-insoluble calcium carbonate or magnesium carbonate, is placed in close proximity to the acid-producing anode. A direct current electrical voltage is provided across the acid-producing anode and the hydroxyl-producing cathode sufficient to generate acid at the acid-producing anode and hydroxyl ions at the hydroxyl-producing cathode. The acid dissolves at least part of the metal carbonate into metal and carbonate ions allowing the metal ions to travel toward the hydroxyl-producing cathode and to combine with the hydroxyl ions to form the metal hydroxide. The carbonate ions travel toward the acid-producing anode and form carbonic acid and/or water and carbon dioxide. Among other uses, the metal hydroxide formed can be employed to absorb acid gases such as carbon dioxide from a gas mixture. The invention can also generate hydrogen and oxidative gases such as oxygen or chlorine.

  7. A comparison of solute-transport solution techniques and their effect on sensitivity analysis and inverse modeling results

    USGS Publications Warehouse

    Mehl, S.; Hill, M.C.

    2001-01-01

    Five common numerical techniques for solving the advection-dispersion equation (finite difference, predictor corrector, total variation diminishing, method of characteristics, and modified method of characteristics) were tested using simulations of a controlled conservative tracer-test experiment through a heterogeneous, two-dimensional sand tank. The experimental facility was constructed using discrete, randomly distributed, homogeneous blocks of five sand types. This experimental model provides an opportunity to compare the solution techniques: the heterogeneous hydraulic-conductivity distribution of known structure can be accurately represented by a numerical model, and detailed measurements can be compared with simulated concentrations and total flow through the tank. The present work uses this opportunity to investigate how three common types of results - simulated breakthrough curves, sensitivity analysis, and calibrated parameter values - change in this heterogeneous situation given the different methods of simulating solute transport. The breakthrough curves show that simulated peak concentrations, even at very fine grid spacings, varied between the techniques because of different amounts of numerical dispersion. Sensitivity-analysis results revealed: (1) a high correlation between hydraulic conductivity and porosity given the concentration and flow observations used, so that both could not be estimated; and (2) that the breakthrough curve data did not provide enough information to estimate individual values of dispersivity for the five sands. This study demonstrates that the choice of assigned dispersivity and the amount of numerical dispersion present in the solution technique influence estimated hydraulic conductivity values to a surprising degree.

  8. Three-dimensional convection in horizontal cylinders - Numerical solutions and comparison with experimental and analytical results

    NASA Technical Reports Server (NTRS)

    Smutek, C.; Bontoux, P.; Roux, B.; Schiroky, G. H.; Hurford, A. C.

    1985-01-01

    The results of a three-dimensional numerical simulation of Boussinesq free convection in a horizontal differentially heated cylinder are presented. The computation was based on a Samarskii-Andreyev scheme (described by Leong, 1981) and a false-transient advancement in time, with vorticity, velocity, and temperature as dependent variables. Solutions for velocity and temperature distributions were obtained for Rayleigh numbers (based on the radius) Ra = 74-18,700, thus covering the core- and boundary-layer-driven regimes. Numerical solutions are compared with asymptotic analytical solutions and experimental data. The numerical results well represent the complex three-dimensional flows found experimentally.

  9. Length Scale Dependence of the Dynamic Properties of Hyaluronic Acid Solutions in the Presence of Salt

    SciTech Connect

    Horkay, Ferenc; Falus, Peter; Hecht, Anne-Marie; Geissler, Erik

    2010-12-07

    In solutions of the charged semirigid biopolymer hyaluronic acid in salt-free conditions, the diffusion coefficient D{sub NSE} measured at high transfer momentum q by neutron spin echo is more than an order of magnitude smaller than that determined by dynamic light scattering, D{sub DLS}. This behavior contrasts with neutral polymer solutions. With increasing salt content, D{sub DLS} approaches D{sub NSE}, which is independent of ionic strength. Contrary to theoretical expectation, the ion-polymer coupling, which dominates the low q dynamics of polyelectrolyte solutions, already breaks down at distance scales greater than the Debye-Hueckel length.

  10. REDUCTION OF PLUTONIUM VALUES IN AN ACIDIC AQUEOUS SOLUTION WITH FORMALDEHYDE

    DOEpatents

    Olson, C.M.

    1959-06-01

    A method is given for reducing Pu to the tetravalent state and lowering the high acidity of dissolver solutions containing U and Pu. Formaldehyde is added to the HNO/sub 3/ solution of U and Pu to effect a formaldehyde to HNO/sub 3/ molar ratio of 0.375:1 to 1.5:1. The Pu can then be removed from the solution by carrier precipitation using BiPO/sub 4/ or by ion exchange. (T.R.H.)

  11. Extremophiles in Mineral Sulphide Heaps: Some Bacterial Responses to Variable Temperature, Acidity and Solution Composition

    PubMed Central

    Watling, Helen R.; Shiers, Denis W.; Collinson, David M.

    2015-01-01

    In heap bioleaching, acidophilic extremophiles contribute to enhanced metal extraction from mineral sulphides through the oxidation of Fe(II) and/or reduced inorganic sulphur compounds (RISC), such as elemental sulphur or mineral sulphides, or the degradation of organic compounds derived from the ore, biota or reagents used during mineral processing. The impacts of variable solution acidity and composition, as well as temperature on the three microbiological functions have been examined for up to four bacterial species found in mineral sulphide heaps. The results indicate that bacteria adapt to sufficiently high metal concentrations (Cu, Ni, Co, Zn, As) to allow them to function in mineral sulphide heaps and, by engaging alternative metabolic pathways, to extend the solution pH range over which growth is sustained. Fluctuating temperatures during start up in sulphide heaps pose the greatest threat to efficient bacterial colonisation. The large masses of ores in bioleaching heaps mean that high temperatures arising from sulphide oxidation are hard to control initially, when the sulphide content of the ore is greatest. During that period, mesophilic and moderately thermophilic bacteria are markedly reduced in both numbers and activity. PMID:27682094

  12. Extremophiles in Mineral Sulphide Heaps: Some Bacterial Responses to Variable Temperature, Acidity and Solution Composition.

    PubMed

    Watling, Helen R; Shiers, Denis W; Collinson, David M

    2015-07-09

    In heap bioleaching, acidophilic extremophiles contribute to enhanced metal extraction from mineral sulphides through the oxidation of Fe(II) and/or reduced inorganic sulphur compounds (RISC), such as elemental sulphur or mineral sulphides, or the degradation of organic compounds derived from the ore, biota or reagents used during mineral processing. The impacts of variable solution acidity and composition, as well as temperature on the three microbiological functions have been examined for up to four bacterial species found in mineral sulphide heaps. The results indicate that bacteria adapt to sufficiently high metal concentrations (Cu, Ni, Co, Zn, As) to allow them to function in mineral sulphide heaps and, by engaging alternative metabolic pathways, to extend the solution pH range over which growth is sustained. Fluctuating temperatures during start up in sulphide heaps pose the greatest threat to efficient bacterial colonisation. The large masses of ores in bioleaching heaps mean that high temperatures arising from sulphide oxidation are hard to control initially, when the sulphide content of the ore is greatest. During that period, mesophilic and moderately thermophilic bacteria are markedly reduced in both numbers and activity.

  13. Removal of cationic dyes by poly(acrylamide-co-acrylic acid) hydrogels in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Şolpan, Dilek; Duran, Sibel; Torun, Murat

    2008-04-01

    Poly(acrylamide-co-acrylic acid (poly(AAm-co-AAc)) hydrogels prepared by irradiating with γ-radiation were used in experiments on swelling, diffusion, and uptake of some cationic dyes such as Safranine-O (SO) and Magenta (M). Poly(AAm-co-AAc) hydrogels irradiated at 8.0 kGy have been used for swelling and diffusion studies in water and cationic dye solutions. The maximum swellings in water, and SO, and M solutions observed are 2700%, 3500%, and 4000%, respectively. Diffusions of water and cationic dyes within hydrogels have been found to be non-Fickian in character. Adsorption of the cationic dyes onto poly(AAm-co-AAc) hydrogels is studied by the batch adsorption technique. The adsorption type was found Langmuir type in the Giles classification system. The moles of adsorbed dye for SO and M per repeating unit in hydrogel (binding ratio, r) have been calculated as 3834×10 -6 and 1323×10 -6, respectively. These results show that poly(AAm-co-AAc) hydrogels can be used as adsorbent for water pollutants such as cationic dyes.

  14. Rapid oxidation and immobilization of arsenic by contact glow discharge plasma in acidic solution.

    PubMed

    Jiang, Bo; Hu, Ping; Zheng, Xing; Zheng, Jingtang; Tan, Minghui; Wu, Mingbo; Xue, Qinzhong

    2015-04-01

    Arsenic is a priority pollutant in aquatic ecosystem and therefore the remediation of arsenic-bearing wastewater is an important environmental issue. This study unprecedentedly reported simultaneous oxidation of As(III) and immobilization of arsenic can be achieved using contact glow discharge process (CGDP). CGDP with thinner anodic wire and higher energy input were beneficial for higher As(V) production efficiency. Adding Fe(II) in CGDP system significantly enhanced the oxidation rate of As(III) due to the generations of additional OH and Fe(IV) species, accompanied with which arsenic can be simultaneously immobilized in one process. Arsenic immobilization can be favorably obtained at solution pH in the range of 4.0-6.0 and Fe(II) concentration from 250 to 1000 μM. The presence of organics (i.e., oxalic acid, ethanol and phenol) retarded the arsenic immobilization by scavenging OH or complexing Fe(III) in aqueous solution. On the basis of these results, a mechanism was proposed that the formed ionic As(V) rapidly coprecipitated with Fe(III) ions or was adsorbed on the ferric oxyhydroxides with the formation of amorphous ferric arsenate-bearing ferric oxyhydroxides. This CGDP-Fenton system was of great interest for engineered systems concerned with the remediation of arsenic containing wastewater. PMID:25600320

  15. Extremophiles in Mineral Sulphide Heaps: Some Bacterial Responses to Variable Temperature, Acidity and Solution Composition

    PubMed Central

    Watling, Helen R.; Shiers, Denis W.; Collinson, David M.

    2015-01-01

    In heap bioleaching, acidophilic extremophiles contribute to enhanced metal extraction from mineral sulphides through the oxidation of Fe(II) and/or reduced inorganic sulphur compounds (RISC), such as elemental sulphur or mineral sulphides, or the degradation of organic compounds derived from the ore, biota or reagents used during mineral processing. The impacts of variable solution acidity and composition, as well as temperature on the three microbiological functions have been examined for up to four bacterial species found in mineral sulphide heaps. The results indicate that bacteria adapt to sufficiently high metal concentrations (Cu, Ni, Co, Zn, As) to allow them to function in mineral sulphide heaps and, by engaging alternative metabolic pathways, to extend the solution pH range over which growth is sustained. Fluctuating temperatures during start up in sulphide heaps pose the greatest threat to efficient bacterial colonisation. The large masses of ores in bioleaching heaps mean that high temperatures arising from sulphide oxidation are hard to control initially, when the sulphide content of the ore is greatest. During that period, mesophilic and moderately thermophilic bacteria are markedly reduced in both numbers and activity.

  16. Trivalent chromium removal from aqueous solutions by a sol–gel synthesized silica adsorbent functionalized with sulphonic acid groups

    SciTech Connect

    Gomez-Gonzalez, Sergio Efrain; Carbajal-Arizaga, Gregorio Guadalupe; Manriquez-Gonzalez, Ricardo; De la Cruz-Hernandez, Wencel; Gomez-Salazar, Sergio

    2014-11-15

    Highlights: • Corpuscular sulphonic acid-functionalized silica holds improved uptake of chromium. • Mesopores on adsorbent facilitate (CH{sub 3}COO){sub 2}Cr{sup +} ion uptake on sulphonate sites. • Formation of chromium acetate sulphonate complex proposed from XPS results. • Fixed bed chromium uptake results suggest potential industrial use. - Abstract: A high capacity hybrid silica adsorbent was synthesized via sol–gel processing with sulphonic acid groups as trivalent chromium complex ions chelators from aqueous solutions. The synthesis included co-condensation of tetraethoxysilane (TEOS) with 3-(mercaptopropyl)trimethoxysilane (MPS), and oxidation of thiol to sulphonic acid groups. Chromium uptake kinetic, batch and fixed-bed experiments were performed to assess the removal of this metal from aqueous solutions. {sup 13}C, {sup 29}Si CPMAS NMR, FTIR, XPS were used to characterize the adsorbent structure and the nature of chromium complexes on the adsorbent surface. Chromium maximum uptake was obtained at pH 3 (72.8 mg/g). Elemental analysis results showed ligand density of 1.48 mmol sulphonic groups/g. About 407 mL of Cr(III) solution (311 mg/L) were treated to breakthrough point reaching ≤0.06 mg/L at the effluent. These results comply with USEPA regulation for chromium concentration in drinking water (≤0.1 mg/L). The adsorbent shows potential to be used in chromium separations to the industrial level.

  17. Helical Symmetry of Nucleic Acids: Obstacle or Help in Structure Solution?

    PubMed

    Urzhumtsev, Alexandre; Urzhumtseva, Ludmila; Baumann, Ulrich

    2016-01-01

    Crystallographic molecular replacement method is the key tool to define an atomic structure of nucleic acids. Frequently nucleic acids are packed forming continuous helices in the crystal. This arrangement of individual molecules in "infinite" pseudo helical structures in crystal may be the reason why the molecular replacement fails to find a unique position of the search atomic model as the method requires. The Patterson function, calculated as a Fourier series with diffraction intensities, has auxiliary peaks for such a molecular packing. Those near the origin peak indicate the orientation of the helices. The coordinates of other peaks are related to the molecular position and the rotation angle between two such "infinite" helices. Thus, the peak analysis allows getting molecular position even without a search model. An intelligent selecting and averaging of the phase sets corresponding to multiple probable positions of the search model again result in a unique solution but in the form of a Fourier synthesis and not a model. This synthesis can be used then to build an atomic model as it is the case for usual phasing methods.

  18. Adsorption of Acid Red 57 from aqueous solutions onto polyacrylonitrile/activated carbon composite.

    PubMed

    El-Bindary, Ashraf A; Diab, Mostafa A; Hussien, Mostafa A; El-Sonbati, Adel Z; Eessa, Ahmed M

    2014-04-24

    The adsorption of Acid Red 57 (AR57) onto Polyacrylonitrile/activated carbon (PAN/AC) composite was investigated in aqueous solution in a batch system with respect to contact time, pH and temperature. Physical characteristics of (PAN/AC) composite such as fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) were obtained. Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were determined. The activation energy of adsorption was also evaluated for the adsorption of AR57 onto (PAN/AC) composite. The pseudo-first-order and pseudo-second-order kinetic models were used to describe the kinetic data. The dynamic data fitted the pseudo-second-order kinetic model well. The activation energy, change of free energy, enthalpy and entropy of adsorption were also evaluated for the adsorption of AR57 onto (PAN/AC) composite. The thermodynamics of the adsorption indicated spontaneous and exothermic nature of the process. The results indicate that (PAN/AC) composite could be employed as low-cost material for the removal of acid dyes from textile effluents. PMID:24463242

  19. Highly selective inorganic crystalline ion-exchange material for Sr{sup 2+} in acidic solutions

    SciTech Connect

    Nenoff, T.M.; Miller, J.E.; Thoma, S.G.; Trudell, D.E.

    1996-12-01

    We report a novel antimony titanate ion exchange material, stable in highly acidic conditions and selective to strontium against competing cations, with possible applications at Defense Waste Sites. Its development was based on good selectivity for Cs and Sr by the CSTs and literature information on the ion exchange properties of antimony compounds. This new material has been tested for the selective removal of parts per million level concentrations of Sr{sup 2+} ions from solutions with a pH in the range of 1 M HNO{sub 3} tO 5.7 M Na{sup +}/0.6 M OH{sup -} (with the most important results in the highly acidic regimes). This doped titanate has been characterized with an array of techniques, including equilibrium distribution coefficient (K{sub d}) determinations over a wide pH range, power X-ray diffraction, TEM, BET, direct-current plasma (DCP), and thermal analyses. 13 refs., 2 figs., 2 tabs.

  20. Evaluation of calix-crown ionophores for selective separation of radio-cesium from acidic nuclear waste solution.

    PubMed

    Mohapatra, P K; Ansari, S A; Sarkar, A; Bhattacharyya, A; Manchanda, V K

    2006-07-01

    Extraction of Cs-137 from nitric acid was carried out using nitrobenzene solutions of calix-crowns such as calix[4]arene-bis(crown-6) (CC-A), calix[4]arene-bis(benzo crown-6) (CC-B) and calix[4]arene-bis(napthocrown-6) (CC-C). CC-C was found to be superior extractant for Cs(I) as compared to the other two calix-crown ligands used in the present study. The effect of diluent on the extraction of Cs(I) indicated the trend: nitrobenzene>dichloroethane>chloroform>decanol>carbon tetrachloride approximately n-hexane approximately toluene. Subsequently, the studies were carried out with nitrobenzene solutions of the calix-crown ligands (mainly CC-C) on the effects of (a) aqueous phase acidity, (b) ligand concentration, and (c) cesium concentration on Cs extraction from nitric acid media. Conditions for quantitative extraction and stripping were optimized and the extracted species conformed to {[CsL]+.[NO3]-.nH2O}. Selectivity studies were carried out using an irradiated natural U target involving tracer amount of fission products activities. Extraction of Cs(I) from a synthetic high level waste solution was also carried out. The promising results obtained in the present studies indicate possible use of the calix-crown ligand for Cs(I) recovery from the acidic high level waste.

  1. Solution blow spun Poly(lactic acid)/Hydroxypropyl methylcellulose nanofibers with antimicrobial properties

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Poly(lactic acid) (PLA) nanofibers containing hydroxypropyl methylcellulose (HPMC) and tetracycline hydrochloride (THC) were solution blow spun from two different solvents, chloroform/acetone (CA, 80:20 v/v) and 2,2,2-triflouroethanol (TFE). The diameter distribution, chemical, thermal, thermal stab...

  2. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  3. Modification of vital wheat gluten with phosphoric acid to produce high free-solution capacity

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Wheat gluten reacts with phosphoric acid to produce natural superabsorbent gels. The gel properties are defined by Fourier Transform Infra-red (FTIR) spectroscopy, 2-dimensional gel electrophoresis (2DE), and uptake of water, salt solutions, and aqueous ethanol. Temperatures above 120'C and dry cond...

  4. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  5. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  6. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  7. 49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed...

  8. Extractant-coated magnetic particles for cobalt and nickel recovery from acidic solution.

    SciTech Connect

    Kaminski, M. D.; Nunez, L.; Chemical Engineering

    1999-04-01

    Waste minimization and recycling practices can often constitute a significant fraction of industrial operating costs. Magnetically assisted chemical separation (MACS) is a simple, cost-effective process that utilizes micrometer-sized magnetic composite materials containing a sorbed layer of chelating or ion exchange material. This paper presents the use of MACS particles for recovering cobalt and nickel from acidic solution.

  9. IMPROVEMENT UPON THE CARRIER PRECIPITATION OF PLUTONIUM IONS FROM NITRIC ACID SOLUTIONS

    DOEpatents

    James, R.A.; Thompson, S.G.

    1958-12-23

    A process is reported for improving the removal of plutonlum by carrier precipitation by the addition of nitrite ions to a nitrlc acid solutlon of neutronirradiated unanium so as to destroy any hydrazine that may be present in the solution since the hydrazine tends to complex the tetravalent plutonium and prevents removal by the carrier precipltate, such as bismuth phospbate.

  10. Spray washing carcasses with alkaline solutions of lauric acid to reduce bacterial contamination

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The ability of lauric acid (LA)-potassium hydroxide (KOH) solutions to reduce carcass bacterial contamination was examined. Skin of carcasses was inoculated with a cecal paste containing antibiotic resistant strains of Escherichia coli, Salmonella Typhimirum, and Campylobacter coli. In one trial, in...

  11. Extractant-coated magnetic particles for cobalt and nickel recovery from acidic solution

    NASA Astrophysics Data System (ADS)

    Kaminski, M. D.; Nuñez, L.

    1999-04-01

    Waste minimization and recycling practices can often constitute a significant fraction of industrial operating costs. Magnetically assisted chemical separation (MACS) is a simple, cost-effective process that utilizes micrometer-sized magnetic composite materials containing a sorbed layer of chelating or ion exchange material. This paper presents the use of MACS particles for recovering cobalt and nickel from acidic solution.

  12. Electrochemical formation of hydroxide for enhancing carbon dioxide and acid gas uptake by a solution

    DOEpatents

    Rau, Gregory Hudson

    2014-07-01

    A system for forming metal hydroxide from a metal carbonate utilizes a water electrolysis cell having an acid-producing anode and a hydroxyl-producing cathode immersed in a water solution of sufficient ionic content to allow an electric current to pass between the hydroxyl-producing cathode and the acid-producing anode. A metal carbonate is placed in close proximity to the acid-producing anode. A direct current electrical voltage is provided across the acid-producing anode and the hydroxyl-producing cathode sufficient to generate acid at the acid-producing anode and hydroxyl ions at the hydroxyl-producing cathode. The acid dissolves at least part of the metal carbonate into metal and carbonate ions allowing the metal ions to travel toward the hydroxyl-producing cathode and to combine with the hydroxyl ions to form the metal hydroxide. The carbonate ions travel toward the acid-producing anode and form carbonic acid and/or water and carbon dioxide.

  13. Acid stability of anti-Helicobacter pyroli IgY in aqueous polyol solution.

    PubMed

    Lee, Kyong Ae; Chang, Sung Keun; Lee, Yoon Jin; Lee, Jong Hwa; Koo, Nan Sook

    2002-09-30

    IgY was separated from a hen's egg yolk that was immunized with Helicobacter pyroli. The anti-H. pyroli IgY activity at acidic pH and the suppressive effect of polyol on acid-induced inactivation of IgY were investigated. Sorbitol and xylitol were used as polyols. IgY was quite stable at pH 5-7. Irreversible inactivation of IgY was observed at pH below 4, and proceeded rapidly at pH below 3. The acid stability of IgY was enhanced in the presence of 30% sorbitol or above. In a 50% aqueous sorbitol solution, an acid-induced inactivation was almost completely suppressed at pH 3. However, the improvement of IgY activity was not observed in the aqueous xylitol solution. IgY showed almost the same activity as native IgY when sucrose was substituted for sorbitol. On the other hand, the xylitol replacement with sucrose did not enhance the acid stability of IgY. The acid-induced inactivation of IgY was related to tryptophyl fluorescence. Fluorescence emission spectra suggested that structural changes near the tryptophan residues may occur under acidic conditions. An increase in sorbitol concentration induced a blue shift. The fluorescence emission of IgY in a 50% sorbitol solution had a peak at 330 nm, which was the same emission peak that was exhibited by native IgY. Sorbitol could, therefore, be used as a good stabilizer of IgY under acidic conditions. PMID:12359091

  14. Gamma irradiation of isocitric and citric acid in aqueous solution: Relevance in prebiotic chemistry

    SciTech Connect

    Negrón-Mendoza, A. Ramos-Bernal, S.

    2015-07-23

    The radiation chemistry of hydroxy acids like citric and isocitric acids is rather scarce, even though they are crucial compounds in biological systems and for food irradiation. The aim of this work is to study the radiolytic behavior of these acids focused on the interconversion induced by radiation of citric and isocitric acid into other members of the Krebs cycle. The results showed that among the products formed were succinic, malonic, malic and other acids related to metabolic pathways, and these results are correlated with its possible role in chemical evolution processes.

  15. Gamma irradiation of isocitric and citric acid in aqueous solution: Relevance in prebiotic chemistry

    NASA Astrophysics Data System (ADS)

    Negrón-Mendoza, A.; Ramos-Bernal, S.

    2015-07-01

    The radiation chemistry of hydroxy acids like citric and isocitric acids is rather scarce, even though they are crucial compounds in biological systems and for food irradiation. The aim of this work is to study the radiolytic behavior of these acids focused on the interconversion induced by radiation of citric and isocitric acid into other members of the Krebs cycle. The results showed that among the products formed were succinic, malonic, malic and other acids related to metabolic pathways, and these results are correlated with its possible role in chemical evolution processes.

  16. Gas dilution system results and application to acid rain utilities

    SciTech Connect

    Jolley-Souders, K.; Geib, R.; Dunn, C.

    1997-12-31

    In 1997, the United States EPA will remove restrictions preventing acid rain utilities from using gas dilution systems for calibration or linearity studies for continuous emissions monitoring, Test Method 205 in 40CFR51 requires that a gas dilution system must produce calibration gases whose measured values are within {+-}2% of predicted values. This paper presents the evaluation of the Environics/CalMat 2020 Dilution System for use in calibration studies. Internal studies show that concentrations generated by this unit are within {+-}0.5% of predicted values. Studies are being conducted by several acid rain utilities to evaluate the Environics/CalMat system using single minor component calibration standards. In addition, an internally generated study is being performed to demonstrate the system`s accuracy using a multi-component gas mixture. Data from these tests will be presented in the final version of the paper.

  17. Pilot-scale decontamination solution test results HGTP-93-0702-02

    SciTech Connect

    Clemmer, R.G.; Allen, R.P.; Bagaasen, L.M.; Fetrow, L.K.

    1993-05-01

    Decontamination solution testing constitutes a task of the Hanford Grout Technology Program (HGTP) at Pacific Northwest Laboratory (PNL). The HGTP provides technical support to the Westinghouse Hanford Company (WHC) Grout Disposal Program. Cementitious grout has been identified as the waste form for low-level radioactive waste. Grout processing equipment, including mixers, pumps, and piping, will require periodic maintenance. Decontamination of components is needed to reduce radiation dose to maintenance workers. The purpose of this work was to develop and test methods for decontaminating grout processing equipment. The proposed method of decontamination is to use a mild chemical solution, such as a 6 N citric acid to dissolve the grout. The method should effectively remove grout without causing degradation of grout processing equipment.

  18. Surface porosity of stone casts resulting from immersion of addition silicone rubber impressions in disinfectant solutions.

    PubMed

    Hiraguchi, Hisako; Kaketani, Masahiro; Hirose, Hideharu; Kikuchi, Hisaji; Yoneyama, Takayuki

    2014-01-01

    This study investigated the effects of immersion of addition silicone rubber impressions in disinfectant solutions on the surface porosity of the resulting stone casts. Five brands of type 2 and 3 addition silicone rubber impression materials and one brand of type 4 dental stone were used. Impressions of a master die designed to simulate an abutment tooth were immersed in disinfectant for 30 minutes. The disinfectants used were 2% glutaraldehyde solution and 0.55% ortho-phthalaldehyde solution. The surface porosities of stone casts obtained from two brands of impression materials immersed in disinfectant for 30 minutes were determined. Results suggest that impression materials immersed in disinfectant solutions need sufficient time before pouring into dental stone.

  19. Comparative Studies on Effects of Acid Solutions on Aquatic Plants by Beam Deflection and Absorbance Spectroscopy Methods.

    PubMed

    Wu, Xing-Zheng; Nie, Liangjiao; Inoue, Tomomi

    2015-01-01

    The beam deflection method and absorbance spectroscopy were applied to study effects of acid solutions on aquatic plants, and their results were compared. Aquatic plants Egeria densa and Ceratophyllum demersum L were used as model plants. In absorbance experiments, a piece of the plants was put in a beaker with 20 mL HCl solution, and absorbance of the HCl solution was measured every 30 min. In beam deflection experiments, a probe beam from a He-Ne laser was focused to a vicinity of the plants in a culture dish with HCl solution by an objective lens, and deflection signals of the probe beam were monitored by a position sensor. Absorbance spectra of the HCl solutions with immersing of the plants showed absorbance below 410 nm, suggesting that some compounds leaked from the plants into the HCl solutions. Changes of absorbance and deflection signals with immersion time were examined for different pH levels. The changing trends of the absorbance and deflection signals with time were similar, but the absorbance changes were delayed for about 2 - 3 h. The absorbance method could not detect the effect of the pH 5.0 HCl solutions on the aquatic plants, while the deflection method could.

  20. Comparative Studies on Effects of Acid Solutions on Aquatic Plants by Beam Deflection and Absorbance Spectroscopy Methods.

    PubMed

    Wu, Xing-Zheng; Nie, Liangjiao; Inoue, Tomomi

    2015-01-01

    The beam deflection method and absorbance spectroscopy were applied to study effects of acid solutions on aquatic plants, and their results were compared. Aquatic plants Egeria densa and Ceratophyllum demersum L were used as model plants. In absorbance experiments, a piece of the plants was put in a beaker with 20 mL HCl solution, and absorbance of the HCl solution was measured every 30 min. In beam deflection experiments, a probe beam from a He-Ne laser was focused to a vicinity of the plants in a culture dish with HCl solution by an objective lens, and deflection signals of the probe beam were monitored by a position sensor. Absorbance spectra of the HCl solutions with immersing of the plants showed absorbance below 410 nm, suggesting that some compounds leaked from the plants into the HCl solutions. Changes of absorbance and deflection signals with immersion time were examined for different pH levels. The changing trends of the absorbance and deflection signals with time were similar, but the absorbance changes were delayed for about 2 - 3 h. The absorbance method could not detect the effect of the pH 5.0 HCl solutions on the aquatic plants, while the deflection method could. PMID:26256609

  1. Study of the decomposition pathway of 12-molybdophosphoric acid in aqueous solutions by micro Raman spectroscopy.

    PubMed

    Bajuk-Bogdanović, D; Uskoković-Marković, S; Hercigonja, R; Popa, A; Holclajtner-Antunović, I

    2016-01-15

    Micro Raman spectroscopy was applied to investigate the speciation of heteropoly and isopoly molybdates in 0.05 and 0.005 M aqueous solutions of 12-molybdophosphoric acid at pH values between 1 and 6. For comparative purposes, (31)P NMR spectroscopy was applied too. It is shown that stability of Keggin anion is influenced both by pH and concentration of solution. The Keggin structure is stable in acidic solutions (pH<1.6) while defective Keggin structures are formed with further alkalization (up to pH5.6). Monolacunary anion PMo11O(39)(7-) is the main component in the pH region from 1.6 to 3.4. Further removal of molybdenyl species causes the appearance of other vacant Keggin structures such as PMo9O31(OH)(3)(6-) and PMo6O(25)(9-) at about pH4. At pH5.0, anion PMo6O(25)(9-) is the main species. In solutions with pH greater than 5.0, heteropolymolybdates disappear completely and isopolymolybdates Mo7O(24)(6-) and MoO(4)(2-) are formed in higher amounts. In more diluted solution of 0.005 M, the decomposition scheme of 12-molybdophosphoric acid solution with increasing of pH takes place without observation of significant amounts of Mo7O(24)(6-) species. If alkalinization is performed with 0.5 M instead of 5 M NaOH, there are no significant changes in the Raman spectra of solutions. It is shown that the spectra of evaporated samples may be used for the identification of molecular species in corresponding concentrated solutions. However, Raman spectra of dry residues of more diluted solutions differ from spectra of corresponding solutions due to the reactions performed during the process of drying and cannot be used for unambiguous identification of species in solution. Acidification of 0.05 M solution of Na2MoO4 shows that at pH>5.6, molybdate anion MoO(4)(2-) dominates, while in the pH range between 5.6 and 1, heptamolybdate anion Mo7O(24)(6-) is preferentially formed.

  2. GIAO-DFT isotropic magnetic shielding constants and spin-spin coupling of tartaric acid in water solution

    NASA Astrophysics Data System (ADS)

    Fideles, Bruna; Oliveira, Leonardo B. A.; Colherinhas, Guilherme

    2016-01-01

    We investigate the nuclear isotropic shielding constants and spin-spin coupling for oxygen and carbons atoms of isomers of tartaric acid in gas phase and in water solutions by Monte Carlo simulation and quantum mechanics calculations using the GIAO-B3LYP approach. Solute polarization effects are included iteratively and play an important role in the quantitative determination of shielding constants. Our MP2/aug-cc-pVTZ results show substantial increases of the dipole moment in solution as compared with the gas phase results (61-221%). The solvent effects on the σ(13O) values are in general small. More appreciable solvent effects can be seen on the σ(17O) and J(Csbnd O).

  3. Adsorptions of some heavy metal ions in aqueous solutions by acrylamide/maleic acid hydrogels

    SciTech Connect

    Saraydin, D.; Karadag, E.; Gueven, O.

    1995-10-01

    In this study, acrylamide-maleic acid (AAm/MA) hydrogels in the form of rod have been prepared by {gamma}-radiation. They have been used for adsorption of some heavy metal ions such as uranium, iron, and copper. For the hydrogel containing 40 mg of maleic acid and irradiated at 3.73 kGy, maximum and minimum swellings in the aqueous solutions of the heavy metal ions have been observed with water (1480%) and the aqueous solution of iron(III) nitrate (410%), respectively. Diffusions of water and heavy metal ions onto hydrogels have been found to be of the non-Fickian type of diffusion. In experiments of uranyl ions adsorption, Type II adsorption has been found. One gram of AAa/MA hydrogels sorbed 14-86 mg uranyl ions from solutions of uranyl acetate, 14-90 mg uranyl ions from solutions of uranyl nitrate, 16-39 mg iron ions from solutions of iron(IV) nitrate, and 28-81 mg copper ions from solutions of copper acetate, while acrylamide hydrogel did not sorb any heavy metals ions.

  4. Acid Catalysis in Basic Solution: A Supramolecular Host PromotesOrthoformate Hydrolysis

    SciTech Connect

    Pluth, Michael D.; Bergman, Robert G.; Raymond, Kenneth N.

    2007-12-12

    Though many enzymes can promote chemical reactions by tuning substrate properties purely through the electrostatic environment of a docking cavity, this strategy has proven challenging to mimic in synthetic host-guest systems. Here we report a highly-charged, water soluble, metal-ligand assembly with a hydrophobic interior cavity that thermodynamically stabilizes protonated substrates and consequently catalyzes the normally acidic hydrolysis of orthoformates in basic solution, with rate accelerations of up to 890-fold. The catalysis reaction obeys Michaelis-Menten kinetics, exhibits competitive inhibition, and the substrate scope displays size selectivity consistent with the constrained binding environment of the molecular host. Synthetic chemists have long endeavored to design host molecules capable of selectively binding slow-reacting substrates and catalyzing their chemical reactions. While synthetic catalysts are often site-specific and require certain properties of the substrate to insure catalysis, enzymes are often able to modify basic properties of the bound substrate such as pK{sub a} in order to enhance reactivity. Two common motifs used by nature to activate otherwise unreactive compounds are the precise arrangement of hydrogen-bonding networks and electrostatic interactions between the substrate and adjacent residues of the protein. Precise arrangement of hydrogen bonding networks near the active sites of proteins can lead to well-tuned pK{sub a}-matching, and can result in pK{sub a} shifts of up to eight units, as shown in bacteriorhodopsin. Similarly, purely electrostatic interactions can greatly favor charged states and have been responsible for pK{sub a} shifts of up to five units for acetoacetate decarboxylase. Attempts have been made to isolate the contributions of electrostatic versus covalent interactions to such pK{sub a} shifts; however this remains a difficult challenge experimentally. This challenge emphasizes the importance of synthesizing

  5. Effective Removal of Tetracycline from Aqueous Solution by Organic Acid-Coated Magnetic Nanoparticles.

    PubMed

    Guo, Liang; Liang, Yuyan; Chen, Xuelan; Xu, Wei; Wu, Kesheng; Wei, Hua; Xiong, Yonghua

    2016-03-01

    Self-assembled iron oxide nanocomposites are good magnetic nano-adsorbents that can be prepared using simple methods. Four types of organic acid-functionalised (oleic acid, undecenoic acid, caprylic acid or hexanoic acid) magnetic nanoparticles (MNPs) were synthesised through a one-pot chemisorption method for the removal of tetracycline (TC) from aqueous solution. The undecenoic acid-coated MNPs (UA-MNPs) exhibited the highest adsorption efficiency and can be easily retrieved with a low-gradient magnetic separator (0.4 Tesla) at pH 5.0 aqueous solution. The TC adsorption process on the UA-MNPs followed the Langmuir isotherm and the maximum adsorption capacities increased from 86.96 mg g(-1) to 222.2 mg g(-1) with the increase in temperature from 288 K to 318 K. The kinetics of adsorption fits pseudo-second-order model perfectly with a rate constant, 5.946 g mg(-1) min(-1) at 298 K. The positive values of the enthalpy (AH) and the negative value of the free energy (AG) indicated an endothermic and spontaneous adsorption process of TC on the UA-MNPs. Moreover, the UA-MNPs possessed excellent ability to adsorb the other three major types of TC antibiotics, including chlortetracycline, oxytetracycline and doxycycline. PMID:27455621

  6. Acid-base and copper-binding properties of three organic matter fractions isolated from a forest floor soil solution

    NASA Astrophysics Data System (ADS)

    van Schaik, Joris W. J.; Kleja, Dan B.; Gustafsson, Jon Petter

    2010-02-01

    Vast amounts of knowledge about the proton- and metal-binding properties of dissolved organic matter (DOM) in natural waters have been obtained in studies on isolated humic and fulvic (hydrophobic) acids. Although macromolecular hydrophilic acids normally make up about one-third of DOM, their proton- and metal-binding properties are poorly known. Here, we investigated the acid-base and Cu-binding properties of the hydrophobic (fulvic) acid fraction and two hydrophilic fractions isolated from a soil solution. Proton titrations revealed a higher total charge for the hydrophilic acid fractions than for the hydrophobic acid fraction. The most hydrophilic fraction appeared to be dominated by weak acid sites, as evidenced by increased slope of the curve of surface charge versus pH at pH values above 6. The titration curves were poorly predicted by both Stockholm Humic Model (SHM) and NICA-Donnan model calculations using generic parameter values, but could be modelled accurately after optimisation of the proton-binding parameters (pH ⩽ 9). Cu-binding isotherms for the three fractions were determined at pH values of 4, 6 and 9. With the optimised proton-binding parameters, the SHM model predictions for Cu binding improved, whereas the NICA-Donnan predictions deteriorated. After optimisation of Cu-binding parameters, both models described the experimental data satisfactorily. Iron(III) and aluminium competed strongly with Cu for binding sites at both pH 4 and pH 6. The SHM model predicted this competition reasonably well, but the NICA-Donnan model underestimated the effects significantly at pH 6. Overall, the Cu-binding behaviour of the two hydrophilic acid fractions was very similar to that of the hydrophobic acid fraction, despite the differences observed in proton-binding characteristics. These results show that for modelling purposes, it is essential to include the hydrophilic acid fraction in the pool of 'active' humic substances.

  7. Dilute nitric or nitrous acid solution containing halide ions as effective media for pure gold dissolution.

    PubMed

    Hojo, Masashi; Yamamoto, Masahiko; Okamura, Kei

    2015-08-14

    The greatly enhanced oxidation ability of dilute aqueous nitric acid (0.10-2.0 mol L(-1)) containing bromide and iodide salts as well as chloride salts has been examined based on the dissolution kinetics of pure gold at 30-60 °C. It has been found that bromide salts are more effective than chloride salts in gaining the ability of dissolving gold in dilute aqueous nitric acid solution. At 60 °C, a piece of gold-wire (ca. 20 mg) is dissolved in 20 mL of as low as 0.10 mol L(-1) HNO3 solution containing 1.0-5.0 mol L(-1) NaBr and the dissolution rate constant, log(k/s(-1)), increases linearly (from -5.78 to -4.52) with the increasing NaBr concentration. The addition of organic solvents, such as acetonitrile and acetic acid, causes acceleration of gold dissolution in LiBr and NaBr solutions. With increasing MeCN contents, for instance, the log(k/s(-1)) value of 0.10 mol L(-1) HNO3 solution containing 2.0 mol L(-1) NaBr increases linearly from -5.30 to -4.61 at 30% (v/v) MeCN. The bromide salts affect the gold dissolution rate constant in the order of KBr < NaBr < LiBr < CaBr2. With increasing NaI concentration (0.20-3.0 mol L(-1)), some acceleration in log(k/s(-1)) of 0.50 or 1.0 mol L(-1) HNO3 solution has been observed; however, the slope of acceleration as the function of NaI concentration is much smaller than that of NaCl or NaBr. The gold dissolution ability has been examined also for nitrous acid containing chloride and bromide ions at 35 °C. The NaNO2 solution containing twice or more amounts of HX (X = Cl, Br) gives the maximum efficiency for gold dissolution, according to the log(k/s(-1)) values of the mixed solutions of NaNO2 (0.10-2.0 mol L(-1)) and HX of various concentrations. The influence of oxidation by dilute nitric and nitrous acids on the gold dissolution is discussed from the standpoint of the redox potentials in "modified" aqueous solutions and not of the changes in the activity coefficients of ions.

  8. Modeling Sucrose Hydrolysis in Dilute Sulfuric Acid Solutions at Pretreatment Conditions for Lignocellulosic Biomass

    SciTech Connect

    Bower, S.; Wickramasinghe, R.; Nagle, N. J.; Schell, D. J.

    2008-01-01

    Agricultural and herbaceous feedstocks may contain appreciable levels of sucrose. The goal of this study was to evaluate the survivability of sucrose and its hydrolysis products, fructose and glucose, during dilute sulfuric acid processing at conditions typically used to pretreat lignocellulose biomass. Solutions containing 25 g/l sucrose with 0.1-2.0% (w/w) sulfuric acid concentrations were treated at temperatures of 160-200 C for 3-12 min. Sucrose was observed to completely hydrolyze at all treatment conditions. However, appreciable concentrations of fructose and glucose were detected and glucose was found to be significantly more stable than fructose. Different mathematical approaches were used to fit the kinetic parameters for acid-catalyzed thermal degradation of these sugars. Since both sugars may survive dilute acid pretreatment, they could provide an additional carbon source for production of ethanol and other bio-based products.

  9. In-line System to Produce High-Purity Acid Solutions.

    PubMed

    Masunaga, Hiroto; Higo, Yuji; Ishii, Mizuo; Maruyama, Noboru; Yamazaki, Shigeo

    2016-01-01

    Herein, we report a new device that generates a high-purity acid solution. It comprises three compartments divided by anion-exchange membranes and filled with ion-exchange resins. Fluorochemical cation-exchange membranes, which tolerate electrochemical wear and permit bulk flow, are inserted between each electrode and the anion-exchange resin. A bipolar boundary is a composite boundary comprising anion and cation exchangers. This device has four bipolar boundaries to separate the location of acid generation from the location where water is electrolyzed. It can tolerate high pressures, resist degradation due to electrolysis at the electrodes, and produce high-purity acid solutions that are free from gases and cationic impurities. The acid solution is generated on the basis of an electrokinetic phenomenon at the surfaces of ion-exchange resins and membranes in an electric field; its concentration can be controlled at rates from 0.01 to 100 μmol/min by adjusting the electrical current applied to the device. PMID:27302592

  10. Vibrational spectroscopic studies and DFT calculations on tribromoacetate and tribromoacetic acid in aqueous solution.

    PubMed

    Rudolph, Wolfram W; Irmer, Gert

    2011-09-01

    Aqueous solutions of sodium tribromoacetate (NaCBr3CO2) and its corresponding acid (CBr3COOH) have been studied using Raman and infrared spectroscopy. The spectra of the species in solution were assigned according to symmetry Cs. Characteristic bands of CBr3CO2-(aq) and the tribromoacetic acid, CBr3COOH(aq), are discussed. For the hydrated anion, the CO2 group, the symmetric CO2 stretching mode at 1332 cm(-1) and the asymmetric stretching mode at 1651 cm(-1) are characteristic while the CO mode at 1730 cm(-1) is characteristic for the spectra of the acid. The stretching mode, νC-C at 912cm(-1) for CBr3CO2-(aq) is 10 cm(-1) lower in the anion compared with that of the acid. These characteristic modes are compared to those in acetate, CH3CO2-(aq). Coupling of the modes are fairly extensive and therefore DFT calculations have been carried out in order to compare the measured spectra with the calculated ones. The geometrical parameters such as bond length and bond angles of the tribromoacetate, and tribromoacetic acid have been obtained and may be compared with the ones published for other acetates and their conjugated acids. CBr3COOH(aq) is a moderately strong acid and the pKa value derived from quantitative Raman measurements is equal to -0.23 at 23°C. The deuterated acid CBr3COOD in heavy water has been measured as well and the assignments were given.

  11. Recovery of water and acid from leach solutions using direct contact membrane distillation.

    PubMed

    Kesieme, Uchenna K; Milne, Nicholas; Cheng, Chu Yong; Aral, Hal; Duke, Mikel

    2014-01-01

    This paper describes for the first time the use of direct contact membrane distillation (DCMD) for acid and water recovery from a real leach solution generated by a hydrometallurgical plant. The leach solutions considered contained H2SO4 or HCl. In all tests the temperature of the feed solution was kept at 60 °C. The test work showed that fluxes were within the range of 18-33 kg/m(2)/h and 15-35 kg/m(2)/h for the H2SO4 and HCl systems, respectively. In the H2SO4 leach system, the final concentration of free acid in the sample solution increased on the concentrate side of the DCMD system from 1.04 M up to 4.60 M. The sulfate separation efficiency was over 99.9% and overall water recovery exceeded 80%. In the HCl leach system, HCl vapour passed through the membrane from the feed side to the permeate. The concentration of HCl captured in the permeate was about 1.10 M leaving behind only 0.41 M in the feed from the initial concentration of 2.13 M. In all the experiments, salt rejection was >99.9%. DCMD is clearly viable for high recovery of high quality water and concentrated H2SO4 from spent sulfuric acid leach solution where solvent extraction could then be applied to recover the sulfuric acid and metals. While HCl can be recovered for reuse using only DCMD. PMID:24569289

  12. [Bactericidal effect of acidic electrolyzed water--comparison of chemical acidic sodium hydrochloride (NaOCl) solution].

    PubMed

    Iwasawa, A; Nakamura, Y

    1996-09-01

    Acidic electrolyzed water is made recently by various kinds of machines and is widely utilized. In this study, we intended to clarify the relationship between the concentration of chloride and pH in the bactericidal effects with acidic electrolyzed water. The effects of weak or strong acidic electrolyzed water were compared with a pseudo-acidic water of pH adjusted by diluted hydrochloric acid and sodium hydroxide, on Staphylococcus aureus, Staphylococcus epidermidis and Pseudomononas aeruginosa. At pH 5.0 approximately 6.0, 3 bacterial strains were killed soon after being exposed to the acidic water containing chloride 50 mg/liter, and the amount of chloride did not change after allowing to stand open for 6 hours. At pH 2.67 approximately 2.80, the bactericidal effects was observed at the concentration of chloride 5 mg/liter, and 80% of chloride remained after allowing to stand for 6 hours. These results indicated that newly made strong acidic water is more effective under a smaller amount of chloride at pH 2.7, and that weak acidic electrolyzed water should be used, if stable bactericidal effect is expected in cleaning the surroundings. PMID:8921674

  13. Biological denitrification of brine: the effect of compatible solutes on enzyme activities and fatty acid degradation.

    PubMed

    Cyplik, Paweł; Piotrowska-Cyplik, Agnieszka; Marecik, Roman; Czarny, Jakub; Drozdzyńska, Agnieszka; Chrzanowski, Łukasz

    2012-09-01

    The effect of the addition of compatible solutes (ectoine and trehalose) on the denitrification process of saline wastewater was studied. In saline wastewater, it was observed that the initial concentration of nitrates was 500 mg N l⁻¹. A fatty substance isolated from oiled bleaching earth (waste of vegetable oil refining process) was used as a source of carbon.The consortium, which was responsible for the denitrification process originated from the wastewater of the vegetable oil industry. The consortium of microorganisms was identified by the use of restriction fragment length polymorphism of 16S rRNA gene amplicons and sequencing techniques. It was noted that ectoine affects significantly the activity of lipase and nitrate reductase, and resulted in faster denitrification compared to saline wastewater with the addition of trehalose or control saline wastewater (without compatible solutes). It was observed that relative enzyme activities of lipase and nitrate reductase increased by 32 and 35%, respectively, in the presence of 1 mM ectoine. This resulted in an increase in specific nitrate reduction rate in the presence of 1 mM ectoine to 5.7 mg N g⁻¹ VSS h⁻¹, which was higher than in the absence of ectoine (3.2 mg N g⁻¹ VSS h⁻¹). The addition of trehalose did not have an effect on nitrate removals. Moreover, it was found that trehalose was used up completely by bacteria as a source of carbon in the denitrification process. The fatty acids were biodegraded by 74% in the presence of 1 mM ectoine.

  14. Enhanced ozonation of dichloroacetic acid in aqueous solution using nanometer ZnO powders.

    PubMed

    Zhai, Xu; Chen, Zhonglin; Zhao, Shuqing; Wang, He; Yang, Lei

    2010-01-01

    Nanometer zinc oxide (ZnO) powders were used as a catalyst to enhance the ozonation for the degradation of dichloroacetic acid (DCAA) in aqueous solution. The batch experiments were carried out to investigate the effects of key factors such as catalyst dosage, ozone dosage, solution pH and tert-butyl alcohol (t-BuOH) on the degradation efficiency of DCAA. Density functional theory (DFT) was adopted to explore the mechanism of generating hydroxyl radical (*OH) on the ZnO surface. The results showed that adsorption and ozonation processes were not effective for DCAA removal, and the addition of ZnO catalyst improved the degradation efficiency of DCAA during ozonation, which caused an increase of 22.8% for DCAA decomposition compared to the case of ozonation alone after 25 min. Under the same experimental conditions, the DCAA decomposition was enhanced by increasing catalyst dosage from 100 to 500 mg/L and ozone dosage from 0.83 to 3.2 mg/L. The catalytic ozonation process is more pronounced than the ozonation process alone at pH 3.93, 6.88, and 10. With increasing the concentration of t-BuOH from 10 to 200 mg/L, the degradation of DCAA was significantly inhibited in the process of catalytic ozonation, indicating that ZnO catalytic ozonation followed *OH reaction mechanism. Based on the experimental results and DFT analysis, it is deduced that the generation of *OH on the ZnO surface is ascribed to the adsorption of molecule ozone followed by the interaction of adsorbed ozone with active sites of the catalyst surface. It is also concluded that ZnO may be an effective catalyst for DCAA removal, which could promote the formation of *OH derived from the catalytic decomposition of ozone. PMID:21235181

  15. Excellent amino acid racemization results from Holocene sand dollars

    NASA Astrophysics Data System (ADS)

    Kosnik, M.; Kaufman, D. S.; Kowalewski, M.; Whitacre, K.

    2015-12-01

    Amino acid racemization (AAR) is widely used as a cost-effective method to date molluscs in time-averaging and taphonomic studies, but it has not been attempted for echinoderms despite their paleobiological importance. Here we demonstrate the feasibility of AAR geochronology in Holocene aged Peronella peronii (Echinodermata: Echinoidea) collected from Sydney Harbour (Australia). Using standard HPLC methods we determined the extent of AAR in 74 Peronella tests and performed replicate analyses on 18 tests. We sampled multiple areas of two individuals and identified the outer edge as a good sampling location. Multiple replicate analyses from the outer edge of 18 tests spanning the observed range of D/Ls yielded median coefficients of variation < 4% for Asp, Phe, Ala, and Glu D/L values, which overlaps with the analytical precision. Correlations between D/L values across 155 HPLC injections sampled from 74 individuals are also very high (pearson r2 > 0.95) for these four amino acids. The ages of 11 individuals spanning the observed range of D/L values were determined using 14C analyses, and Bayesian model averaging was used to determine the best AAR age model. The averaged age model was mainly composed of time-dependent reaction kinetics models (TDK, 71%) based on phenylalanine (Phe, 94%). Modelled ages ranged from 14 to 5539 yrs, and the median 95% confidence interval for the 74 analysed individuals is ±28% of the modelled age. In comparison, the median 95% confidence interval for the 11 calibrated 14C ages was ±9% of the median age estimate. Overall Peronella yields exceptionally high-quality AAR D/L values and appears to be an excellent substrate for AAR geochronology. This work opens the way for time-averaging and taphonomic studies of echinoderms similar to those in molluscs.

  16. Molecular dynamics simulation analysis of small-angle neutron scattering by a solution of stearic acid in benzene

    NASA Astrophysics Data System (ADS)

    Eremin, R. A.; Kholmurodov, Kh. T.; Petrenko, V. I.; Rosta, L.; Avdeev, M. V.

    2014-01-01

    Data of small-angle neutron scattering by a diluted solution of stearic acid in deuterated benzene have been analyzed using the results of molecular dynamics simulation. The molecular dynamics simulation approach has been used to calculate the time-averaged distribution of the neutron scattering length density at the interface between the acid molecule and the solvent. It has been shown that the organization of the solvent at the interface with the acid molecule leads to a modulation of the neutron scattering length density and makes a significant contribution to the scattering. This contribution should be taken into account when interpreting the experimental small-angle neutron scattering curves for both the considered system and its analogues.

  17. Enhanced stability of the model mini-protein in amino acid ionic liquids and their aqueous solutions.

    PubMed

    Chevrot, Guillaume; Fileti, Eudes Eterno; Chaban, Vitaly V

    2015-10-15

    Using molecular dynamics simulations, the structure of model mini-protein was thoroughly characterized in the imidazolium-based amino acid ionic liquids and their aqueous solutions. Complete substitution of water by organic cations and anions further results in hindered conformational flexibility of the mini-protein. This observation suggests that amino acid-based ionic liquids are able to defend proteins from thermally induced denaturation. We show by means of radial distributions that the mini-protein is efficiently solvated by both solvents due to a good mutual miscibility. Amino acid-based anions prevail in the first coordination sphere of positively charged sites of the mini-protein whereas water molecules prevail in the first coordination sphere of negatively charged sites of the mini-protein. PMID:26250927

  18. Standard enthalpies of formation of γ-aminobutyric acid and the products of its dissociation in aqueous solution

    NASA Astrophysics Data System (ADS)

    Lytkin, A. I.; Chernikov, V. V.; Krutova, O. N.; Skvortsov, I. A.; Korchagina, A. S.

    2016-09-01

    Heat effects of the dissolution of crystalline γ-aminobutyric acid in water and potassium hydroxide solutions are determined by direct colorimetry at 298.15 K. Standard enthalpies of formation of γ-aminobutyric acid and the products of its dissociation in aqueous solution are calculated.

  19. PROCESS FOR EXTRACTING NEPTUNIUM AND PLUTONIUM FROM NITRIC ACID SOLUTIONS OF SAME CONTAINING URANYL NITRATE WITH A TERTIARY AMINE

    DOEpatents

    Sheppard, J.C.

    1962-07-31

    A process of selectively extracting plutonium nitrate and neptunium nitrate with an organic solution of a tertiary amine, away from uranyl nitrate present in an aqueous solution in a maximum concentration of 1M is described. The nitric acid concentration is adjusted to about 4M and nitrous acid is added prior to extraction. (AEC)

  20. Microbial shelf life determination of vacuum-packaged fresh beef treated with polylactic acid, lactic acid, and nisin solutions.

    PubMed

    Ariyapitipun, T; Mustapha, A; Clarke, A D

    1999-08-01

    The effectiveness of polylactic acid, lactic acid, nisin, and combinations of the acids and nisin on extending the shelf-life of raw beef was determined. Fresh beef pieces (5 by 5 by 2.5 cm) were dipped in a solution of 2% low molecular weight polylactic acid (LMW-PLA), 2% lactic acid (LA), 200 IU of nisin per ml, or the combinations of nisin in either 2% LMW-PLA or 2% LA. The samples were then drip-dried, vacuum-packaged, and stored at 4 degrees C for up to 56 days. The beef surface pH values and numbers of psychrotrophic aerobic bacteria, psychrotrophic and mesophilic Enterobacteriaceae, Pseudomonas, and Lactobacillus were determined weekly for 56 days. The average surface pH values of the beef samples treated with 2% LMW-PLA or the combination of 200 IU of nisin per ml and 2% LMW-PLA were significantly reduced to 5.19 and 5.17, respectively, at day 0 (P < or = 0.05), while those decontaminated with 2% LA or 200 IU of nisin per ml in 2% LA solution were significantly decreased from 5.62 to 4.98 and 4.96, respectively. The 2% LMW-PLA, 2% LA, or the combinations of each acid and nisin showed immediate inhibitory effects on psychrotrophic aerobic bacteria (1.94, 2.36, 2.59, and 1.76 log reduction, respectively), psychrotrophic Enterobacteriaceae (1.37, 1.86, 1.77, and 1.35 log reduction, respectively), mesophilic Enterobacteriaceae (1.00, 1.00, 0.82, and 0.68 log reduction, respectively), and Pseudomonas (1.77, 1.57, 1.76, and 1.41 log reduction, respectively) on fresh beef (P < or = 0.05). The reduction was evident up to 56 days as seen by the numbers of Enterobacteriaceae and Pseudomonas (P < or = 0.05). Because there was no interaction between treatments and storage times, the data in each period were combined and presented as effect of treatments on overall microbial counts of fresh beef. It was found that 2% LMW-PLA, 2% LA, and the combinations of each acid and nisin significantly lowered the population of the above organisms compared with the untreated control

  1. Spectral and Acid-Base Properties of Hydroxyflavones in Micellar Solutions of Cationic Surfactants

    NASA Astrophysics Data System (ADS)

    Lipkovska, N. A.; Barvinchenko, V. N.; Fedyanina, T. V.; Rugal', A. A.

    2014-09-01

    It has been shown that the spectral characteristics (intensity, position of the absorption band) and the acid-base properties in a series of structurally similar hydroxyflavones depend on the concentration of the cationic surfactants miramistin and decamethoxin in aqueous solutions, and the extent of their changes is more pronounced for hydrophobic quercetin than for hydrophilic rutin. For the first time, we have determined the apparent dissociation constants of quercetin and rutin in solutions of these cationic surfactants (pKa1) over a broad concentration range and we have established that they decrease in the series water-decamethoxin-miramistin.

  2. The effect of high-energy radiation on aqueous solution of Acid Red 1 textile dye

    NASA Astrophysics Data System (ADS)

    Földváry, Cs. M.; Wojnárovits, L.

    2007-08-01

    The effect of high-energy radiation on Acid Red 1 (AR1) azo-dye solution was investigated by UV-Vis spectroscopy and chemical oxygen demand (COD) measurements. Doses in the order of 10 kGy cause complete decolouration of the 10 -3-10 -4 mol dm -3 solutions; however, for complete mineralization doses higher by 1-2 order of magnitude are needed. Hydrated electrons and H rad atom are more effective in fading reaction, while the rad OH radicals have higher efficiency in mineralization. The HO 2•/O 2•- radical-radical anion pair is rather inefficient in fading reaction.

  3. [Effects of Low-Molecular-Weight Organic Acids on the Speciation of Pb in Purple Soil and Soil Solution].

    PubMed

    Liu, Jiang; Jiang, Tao; Huang, Rong; Zhang, Jin-zhong; Chen, Hong

    2016-04-15

    Lead (Pb) in purple soil was selected as the research target, using one-step extraction method with 0.01 mol · L⁻¹ sodium nitrate as the background electrolyte to study the release effect of citric acid (CA), tartaric acid (TA) and acetic acid (AC) with different concentrations. Sequential extraction and geochemical model (Visual Minteq v3.0) were applied to analyze and predict the speciation of Pb in soil solid phase and soil solution phase. Then the ebvironmental implications and risks of low-molecule weight organic acid (LMWOA) on soil Pb were analyzed. The results indicated that all three types of LMWOA increased the desorption capacity of Pb in purple soil, and the effect followed the descending order of CA > TA > AC. After the action of LMWOAs, the exchangeable Pb increased; the carbonate-bound Pb and Fe-Mn oxide bound Pb dropped in soil solid phase. Organic bound Pb was the main speciation in soil solution phase, accounting for 45.16%-75.05%. The following speciation of Pb in soil solution was free Pb, accounting for 22.71%-50.25%. For CA and TA treatments, free Pb ions and inorganic bound Pb in soil solution increased with increasing LMWOAs concentration, while organic bound Pb suffered a decrease in this process. An opposite trend for AC treatment was observed compared with CA and TA treatments. Overall, LMWOAs boosted the bioavailability of Pb in purple soil and had a potential risk to contaminate underground water. Among the three LMWOAs in this study, CA had the largest potential to activate soil Pb. PMID:27548978

  4. [Effects of Low-Molecular-Weight Organic Acids on the Speciation of Pb in Purple Soil and Soil Solution].

    PubMed

    Liu, Jiang; Jiang, Tao; Huang, Rong; Zhang, Jin-zhong; Chen, Hong

    2016-04-15

    Lead (Pb) in purple soil was selected as the research target, using one-step extraction method with 0.01 mol · L⁻¹ sodium nitrate as the background electrolyte to study the release effect of citric acid (CA), tartaric acid (TA) and acetic acid (AC) with different concentrations. Sequential extraction and geochemical model (Visual Minteq v3.0) were applied to analyze and predict the speciation of Pb in soil solid phase and soil solution phase. Then the ebvironmental implications and risks of low-molecule weight organic acid (LMWOA) on soil Pb were analyzed. The results indicated that all three types of LMWOA increased the desorption capacity of Pb in purple soil, and the effect followed the descending order of CA > TA > AC. After the action of LMWOAs, the exchangeable Pb increased; the carbonate-bound Pb and Fe-Mn oxide bound Pb dropped in soil solid phase. Organic bound Pb was the main speciation in soil solution phase, accounting for 45.16%-75.05%. The following speciation of Pb in soil solution was free Pb, accounting for 22.71%-50.25%. For CA and TA treatments, free Pb ions and inorganic bound Pb in soil solution increased with increasing LMWOAs concentration, while organic bound Pb suffered a decrease in this process. An opposite trend for AC treatment was observed compared with CA and TA treatments. Overall, LMWOAs boosted the bioavailability of Pb in purple soil and had a potential risk to contaminate underground water. Among the three LMWOAs in this study, CA had the largest potential to activate soil Pb.

  5. Composition and process for separating cesium ions from an acidic aqueous solution also containing other ions

    DOEpatents

    Dietz, Mark L.; Horwitz, E. Philip; Bartsch, Richard A.; Barrans, Jr., Richard E.; Rausch, David

    1999-01-01

    A crown ether cesium ion extractant is disclosed as is its synthesis. The crown ether cesium ion extractant is useful for the selective purification of cesium ions from aqueous acidic media, and more particularly useful for the isolation of radioactive cesium-137 from nuclear waste streams. Processes for isolating cesium ions from aqueous acidic media using the crown ether cesium extractant are disclosed as are processes for recycling the crown ether cesium extractant and processes for recovering cesium from a crown ether cesium extractant solution.

  6. Composition and process for separating cesium ions from an acidic aqueous solution also containing other ions

    DOEpatents

    Dietz, M.L.; Horwitz, E.P.; Bartsch, R.A.; Barrans, R.E. Jr.; Rausch, D.

    1999-03-30

    A crown ether cesium ion extractant is disclosed as is its synthesis. The crown ether cesium ion extractant is useful for the selective purification of cesium ions from aqueous acidic media, and more particularly useful for the isolation of radioactive cesium-137 from nuclear waste streams. Processes for isolating cesium ions from aqueous acidic media using the crown ether cesium extractant are disclosed as are processes for recycling the crown ether cesium extractant and processes for recovering cesium from a crown ether cesium extractant solution. 4 figs.

  7. Silver-Catalyzed Decarboxylative Radical Azidation of Aliphatic Carboxylic Acids in Aqueous Solution.

    PubMed

    Liu, Chao; Wang, Xiaoqing; Li, Zhaodong; Cui, Lei; Li, Chaozhong

    2015-08-12

    We report herein an efficient and general method for the decarboxylative azidation of aliphatic carboxylic acids. Thus, with AgNO3 as the catalyst and K2S2O8 as the oxidant, the reactions of various aliphatic carboxylic acids with tosyl azide or pyridine-3-sulfonyl azide in aqueous CH3CN solution afforded the corresponding alkyl azides under mild conditions. A broad substrate scope and wide functional group compatibility were observed. A radical mechanism is proposed for this site-specific azidation.

  8. Hexavalent uranium diffusion into soils from concentrated acidic and alkaline solutions

    SciTech Connect

    Tokunaga, Tetsu K.; Wan, Jiamin; Pena, Jasquelin; Sutton, Stephen R.; Newville, Matthew

    2004-03-29

    Uranium contamination of soils and sediments often originates from acidic or alkaline waste sources, with diffusion being a major transport mechanism. Measurements of U(VI) diffusion from initially pH 2 and pH 11 solutions into a slightly alkaline Altamont soil and a neutral Oak Ridge soil were obtained through monitoring uptake from boundary reservoirs and from U concentration profiles within soil columns. The soils provided pH buffering, resulting in diffusion at nearly constant pH. Micro x-ray absorption near edge structure spectra confirmed that U remained in U(VI) forms in all soils. Time trends of U(VI) depletion from reservoirs, and U(VI) concentration profiles within soil columns yielded K{sub d} values consistent with those determined in batch tests at similar concentrations ({approx} 1 mM), and much lower than values for sorption at much lower concentrations (nM to {mu}M). These results show that U(VI) transport at high concentrations can be relatively fast at non-neutral pH, with negligible surface diffusion, because of weak sorption.

  9. Mechanisms of enhanced total organic carbon elimination from oxalic acid solutions by electro-peroxone process.

    PubMed

    Wang, Huijiao; Yuan, Shi; Zhan, Juhong; Wang, Yujue; Yu, Gang; Deng, Shubo; Huang, Jun; Wang, Bin

    2015-09-01

    Electro-peroxone (E-peroxone) is a novel electrocatalytic ozonation process that combines ozonation and electrolysis process to enhance pollutant degradation during water and wastewater treatment. This enhancement has been mainly attributed to several mechanisms that increase O3 transformation to ·OH in the E-peroxone system, e.g., electro-generation of H2O2 from O2 at a carbon-based cathode and its subsequent peroxone reaction with O3 to ·OH, electro-reduction of O3 to ·OH at the cathode, and O3 decomposition to ·OH at high local pH near the cathode. To get more insight how these mechanisms contribute respectively to the enhancement, this study investigated total organic carbon (TOC) elimination from oxalic acid (OA) solutions by the E-peroxone process. Results show that the E-peroxone process significantly increased TOC elimination rate by 10.2-12.5 times compared with the linear addition of the individual rates of corresponding ozonation and electrolysis process. Kinetic analyses reveal that the electrochemically-driven peroxone reaction is the most important mechanism for the enhanced TOC elimination rate, while the other mechanisms contribute minor to the enhancement by a factor of 1.6-2.5. The results indicate that proper selection of electrodes that can effectively produce H2O2 at the cathode is critical to maximize TOC elimination in the E-peroxone process.

  10. Mechanisms of enhanced total organic carbon elimination from oxalic acid solutions by electro-peroxone process.

    PubMed

    Wang, Huijiao; Yuan, Shi; Zhan, Juhong; Wang, Yujue; Yu, Gang; Deng, Shubo; Huang, Jun; Wang, Bin

    2015-09-01

    Electro-peroxone (E-peroxone) is a novel electrocatalytic ozonation process that combines ozonation and electrolysis process to enhance pollutant degradation during water and wastewater treatment. This enhancement has been mainly attributed to several mechanisms that increase O3 transformation to ·OH in the E-peroxone system, e.g., electro-generation of H2O2 from O2 at a carbon-based cathode and its subsequent peroxone reaction with O3 to ·OH, electro-reduction of O3 to ·OH at the cathode, and O3 decomposition to ·OH at high local pH near the cathode. To get more insight how these mechanisms contribute respectively to the enhancement, this study investigated total organic carbon (TOC) elimination from oxalic acid (OA) solutions by the E-peroxone process. Results show that the E-peroxone process significantly increased TOC elimination rate by 10.2-12.5 times compared with the linear addition of the individual rates of corresponding ozonation and electrolysis process. Kinetic analyses reveal that the electrochemically-driven peroxone reaction is the most important mechanism for the enhanced TOC elimination rate, while the other mechanisms contribute minor to the enhancement by a factor of 1.6-2.5. The results indicate that proper selection of electrodes that can effectively produce H2O2 at the cathode is critical to maximize TOC elimination in the E-peroxone process. PMID:25989593

  11. [Study on the stability variation mechanism of humic acid water solution after radiated by the UV light].

    PubMed

    Wang, Wen-Dong; Zhou, Li-chuan; Ding, Zhen-Zhen; Wang, Hong-Ping; Sun, Xue-Jun

    2013-10-01

    Humic acid widely presents in various surface waters. Molecular structure has significant impacts on its physical and chemical properties. To explore the stability variation of humic acid before and after the UV light radiation, spectroscopic and electrochemical analysis were applied in this paper. Structural parameters selected in the experiments include reactive sites, such as phenolic hydroxyl and carboxyl contents, Zeta potential, and colloidal size. It was found that there was little humic acid being removed in the solution without UV radiation pretreatment; while its remove ratio increased notably with radiation time. After 3 h pretreatment, humic acid removal ratio was above 80% in coagulation. Spectroscopy analysis results showed that partial of the groups with fluorescent effects might be shed or rearranged after the radiation; while its aromatic structure was not destroyed. Both the Zeta potential and average colloidal size decreased with the radiation time, which was not conducive to the aggregation of humic acid. However, -OH content decreased slightly after the UV radiation, and new carboxyl and carbonyl groups formed simultaneously. The increasing of the reactive sites and the improvement of the reaction effectiveness were the major reasons leading to humic acid stability decrease in PAC! coagulation. PMID:24364311

  12. [Study on the stability variation mechanism of humic acid water solution after radiated by the UV light].

    PubMed

    Wang, Wen-Dong; Zhou, Li-chuan; Ding, Zhen-Zhen; Wang, Hong-Ping; Sun, Xue-Jun

    2013-10-01

    Humic acid widely presents in various surface waters. Molecular structure has significant impacts on its physical and chemical properties. To explore the stability variation of humic acid before and after the UV light radiation, spectroscopic and electrochemical analysis were applied in this paper. Structural parameters selected in the experiments include reactive sites, such as phenolic hydroxyl and carboxyl contents, Zeta potential, and colloidal size. It was found that there was little humic acid being removed in the solution without UV radiation pretreatment; while its remove ratio increased notably with radiation time. After 3 h pretreatment, humic acid removal ratio was above 80% in coagulation. Spectroscopy analysis results showed that partial of the groups with fluorescent effects might be shed or rearranged after the radiation; while its aromatic structure was not destroyed. Both the Zeta potential and average colloidal size decreased with the radiation time, which was not conducive to the aggregation of humic acid. However, -OH content decreased slightly after the UV radiation, and new carboxyl and carbonyl groups formed simultaneously. The increasing of the reactive sites and the improvement of the reaction effectiveness were the major reasons leading to humic acid stability decrease in PAC! coagulation.

  13. Electro-oxidation of methanol on Pt(111) in acid solutions: effects of electrolyte anions during electrocatalytic reactions

    NASA Astrophysics Data System (ADS)

    Ogasawara, Hirohito; Ito, Masatoki

    1995-10-01

    The electro-oxidation of methanol on a Pt(111) surface in both sulfuric and perchloric acid solutions was investigated by combined apparatus under both ultra-high vacuum and electrochemical environments. In sulfuric acid solution, a strong lateral interaction was observed between adsorbed bisulfate and CO derived from methanol. Coadsorption of CO derived from methanol with bisulfate ion yielded a (√7 × √7)-R19.1°-CO-bisulfate structure. In perchloric acid solution, however, no lateral interaction between adsorbed CO and perchlorate was seen. The difference in reaction rates of methanol oxidation in both solutions was explained by these specific anion adsorption effects.

  14. Thermodynamic characteristics of the interaction between nicotinic acid and phenylalanine in an aqueous buffer solution at 298 K

    NASA Astrophysics Data System (ADS)

    Badelin, V. G.; Tyunina, E. Yu.; Mezhevoi, I. N.; Tarasova, G. N.

    2013-08-01

    The interaction between L-phenylalanine and nicotinic acid is studied by solution calorimetry in an aqueous buffer solution (pH 7.35) at different ratios of the reagents. Experimental data on the enthalpy of dissolution of amino acid in the buffer solution of nicotinic acid at 298.15 K are calculated. The values of thermodynamic parameters for the complexation of L-phenylalanine with nicotinic acid are calculated. It is shown that the formation of a 1: 2 molecular complex is stabilized by the entropy factor due to the dominant role of the dehydration effect of initial reagents.

  15. Direct determination of peracetic acid, hydrogen peroxide, and acetic acid in disinfectant solutions by far-ultraviolet absorption spectroscopy.

    PubMed

    Higashi, Noboru; Yokota, Hiroshi; Hiraki, Satoru; Ozaki, Yukihiro

    2005-04-01

    In this paper we propose a rapid and highly selective far-ultraviolet (FUV) spectroscopic method for the simultaneous determination of peracetic acid (PAA), hydrogen peroxide, and acetic acid (AA). For this purpose we developed a novel FUV spectrometer that enables us to measure the spectra down to 180 nm. Direct determination of PAA, H(2)O(2), and AA, the three main species in disinfectant solutions, was carried out by using their absorption bands in the 180-220-nm region. The proposed method does not require any reagents or catalysts, a calibration standard, and a complicated procedure for the analysis. The only preparation procedure requested is a dilution of H(2)O(2) with pure water to a concentration range lower than 0.2 wt % in the sample solutions. Usually, the required concentration range can be obtained by the 10 times volume dilution of the actual disinfectant solutions. As the measured sample does not leave any impurity for the disinfection, it can be reused completely by using a circulation system. The detection limit for PAA of the new FUV spectrometer was evaluated to be 0.002 wt %, and the dynamic ranges of the measured concentrations were from 0 to 0.05 wt %, from 0 to 0.2 wt %, and from 0 to 0.2 wt % for PAA, H(2)O(2), and AA, respectively. The response time for the simultaneous determination of the three species is 30 s, and the analysis is applicable even to the flowing samples. This method may become a novel approach for the continuous monitoring of PAA in disinfectant solutions on the process of sterilization. PMID:15801764

  16. Thermodynamic studies of ionic hydration and interactions for amino acid ionic liquids in aqueous solutions at 298.15 K.

    PubMed

    Dagade, Dilip H; Madkar, Kavita R; Shinde, Sandeep P; Barge, Seema S

    2013-01-31

    Amino acid ionic liquids are a special class of ionic liquids due to their unique acid-base behavior, biological significance, and applications in different fields such as templates in synthetic chemistry, stabilizers for biological macromolecules, etc. The physicochemical properties of these ionic liquids can easily be altered by making the different combinations of amino acids as anion along with possible cation modification which makes amino acid ionic liquids more suitable to understand the different kinds of molecular and ionic interactions with sufficient depth so that they can provide fruitful information for a molecular level understanding of more complicated biological processes. In this context, volumetric and osmotic coefficient measurements for aqueous solutions containing 1-ethyl-3-methylimidazolium ([Emim]) based amino acid ionic liquids of glycine, alanine, valine, leucine, and isoleucine are reported at 298.15 K. From experimental osmotic coefficient data, mean molal activity coefficients of ionic liquids were estimated and analyzed using the Debye-Hückel and Pitzer models. The hydration numbers of ionic liquids in aqueous solutions were obtained using activity data. Pitzer ion interaction parameters are estimated and compared with other electrolytes reported in the literature. The nonelectrolyte contribution to the aqueous solutions containing ionic liquids was studied by calculating the osmotic second virial coefficient through an application of the McMillan-Mayer theory of solution. It has been found that the second osmotic virial coefficient which includes volume effects correlates linearly with the Pitzer ion interaction parameter estimated independently from osmotic data as well as the hydrophobicity of ionic liquids. The enthalpy-entropy compensation effect, explained using the Starikov-Nordén model of enthalpy-entropy compensation, and partial molar entropy analysis for aqueous [Emim][Gly] solutions are made by using experimental Gibb

  17. Precipitation of jarosite-type double salts from spent acid solutions from a chemical coal cleaning process

    SciTech Connect

    Norton, G.

    1990-09-21

    The precipitation of jarosite compounds to remove Na, K, Fe, and SO{sub 4}{sup 2{minus}} impurities from spent acid solutions from a chemical coal cleaning process was studied. Simple heating of model solutions containing Fe{sub 2}(SO{sub 4}){sub 3}, Na{sub 2}SO{sub 4}, and K{sub 2}SO{sub 4} caused jarosite (KFe{sub 3}(SO{sub 4}){sub 2}(OH){sub 6}) to form preferentially to natrojarosite (NaFe{sub 3}(SO{sub 4}){sub 2}(OH){sub 6}). Virtually all of the K, about 90% of the Fe, and about 30% of the SO{sub 4}{sup 2{minus}} could be precipitated from those solutions at 95{degree}C, while little or no Na was removed. However, simple heating of model solutions containing only Fe{sub 2}(SO{sub 4}){sub 3} and Na{sub 2}SO{sub 4} up to 95{degree}C for {le}12 hours produced low yields of jarosite compounds, and the Fe concentration in the solution had to be increased to avoid the formation of undesirable Fe compounds. Precipitate yields could be increased dramatically in model solutions of Na{sub 2}SO{sub 4}/Fe{sub 2}(SO{sub 4}){sub 3} containing excess Fe by using either CaCO{sub 3}, Ca(OH){sub 2}, or ZnO to neutralize H{sub 2}SO{sub 4} released during hydrolysis of the Fe{sub 2}(SO{sub 4}){sub 3} and during the precipitation reactions. Results obtained from the studies with model solutions were applied to spent acids produced during laboratory countercurrent washing of coal which had been leached with a molten NaOH/KOH mixture. Results indicated that jarosite compounds can be precipitated effectively from spent acid solutions by heating for 6 hours at 80{degree}C while maintaining a pH of about 1.5 using CaCO{sub 3}.

  18. Solution High-Energy Burst Assembly (SHEBA) results from subprompt critical experiments with uranyl fluoride fuel

    SciTech Connect

    Cappiello, C.C.; Butterfield, K.B.; Sanchez, R.G.

    1997-10-01

    The Solution High-Energy Burst Assembly (SHEBA) was originally constructed during 1980 and was designed to be a clean free-field geometry, right-circular, cylindrically symmetric critical assembly employing U(5%)O{sub 2}F{sub 2} solution as fuel. A second version of SHEBA, employing the same fuel but equipped with a fuel pump and shielding pit, was commissioned in 1993. This report includes data and operating experience for the 1993 SHEBA only. Solution-fueled benchmark work focused on the development of experimental measurements of the characterization of SHEBA; a summary of the results are given. A description of the system and the experimental results are given in some detail in the report. Experiments were designed to: (1) study the behavior of nuclear excursions in a low-enrichment solution, (2) evaluate accidental criticality alarm detectors for fuel-processing facilities, (3) provide radiation spectra and dose measurements to benchmark radiation transport calculations on a low-enrichment solution system similar to centrifuge enrichment plants, and (4) provide radiation fields to calibrate personnel dosimetry. 15 refs., 37 figs., 10 tabs.

  19. Effects of applied potential on the stress corrosion cracking behavior of 7003 aluminum alloy in acid and alkaline chloride solutions

    NASA Astrophysics Data System (ADS)

    Zhang, Xiao-yan; Song, Ren-guo; Sun, Bin; Lu, Hai; Wang, Chao

    2016-07-01

    Potentiodynamic polarization tests and slow strain rate test (SSRT) in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking (SCC) behavior of 7003 aluminum alloy (AA7003) in acid and alkaline chloride solutions under various applied potentials ( E a). The results show that AA7003 is to a certain extent susceptible to SCC via anodic dissolution (AD) at open-circuit potential (OCP) and is highly susceptible to hydrogen embrittlement (HE) at high negative E a in the solutions with pH levels of 4 and 11. The susceptibility increases with negative shift in the potential when E a is less than -1000 mV vs. SCE. However, the susceptibility distinctly decreases because of the inhibition of AD when E a is equal to -1000 mV vs. SCE. In addition, the SCC susceptibility of AA7003 in the acid chloride solution is higher than that in the alkaline solution at each potential. Moreover, the effect of hydrogen on SCC increases with increasing hydrogen ion concentration.

  20. Towards the experimental decomposition rate of carbonic acid (H2CO3) in aqueous solution.

    PubMed

    Tautermann, Christofer S; Voegele, Andreas F; Loerting, Thomas; Kohl, Ingrid; Hallbrucker, Andreas; Mayer, Erwin; Liedl, Klaus R

    2002-01-01

    Dry carbonic acid has recently been shown to be kinetically stable even at room temperature. Addition of water molecules reduces this stability significantly, and the decomposition (H2CO3 + nH2O --> (n+1)H2O + CO2) is extremely accelerated for n = 1, 2, 3. By including two water molecules, a reaction rate that is a factor of 3000 below the experimental one (10 s(-1)) at room temperature was found. In order to further remove the gap between experiment and theory, we increased the number of water molecules involved to 3 and took into consideration different mechanisms for thorough elucidation of the reaction. A mechanism whereby the reaction proceedes via a six-membered transition state turns out to be the most efficient one over the whole examined temperature range. The determined reaction rates approach experimental values in aqueous solution reasonably well; most especially, a significant increase in the rates in comparison to the decomposition reaction with fewer water molecules is found. Further agreement with experiment is found in the kinetic isotope effects (KIE) for the deuterated species. For water-free carbonic acid, the KIE (i.e., kH2CO3/kD2CO3) for the decomposition reaction is predicted to be 220 at 300 K, whereas it amounts to 2.2-3.0 for the investigated mechanisms including three water molecules. This result is therefore reasonably close to the experimental value of 2 (at 300 K). These KIEs are in much better accordance with the experiment than the KIE for decomposition with fewer water entities. PMID:11822465

  1. Amino acid metabolism during total parenteral nutrition in healthy volunteers: evaluation of a new amino acid solution.

    PubMed

    Berard, M P; Hankard, R; Cynober, L

    2001-10-01

    The aim of this study was to determine the metabolism and the tolerance of a new amino acid (AA) solution administered under conditions mimicking cyclical parenteral nutrition (PN) in humans. Eight healthy volunteers received peripheral PN for 10 h providing 10.5 mg N x kg(-1) x h(-1) and 2.0 kcal x kg(-1) x h(-1) (glucose-to-lipids ratio: 70/30%). For adaptation, a non-protein energy intake was increased progressively for 90 min; thereafter, AA infusion was started and maintained at a constant rate for 10 h. Plasma and urine concentrations of all the AAs were measured before, during and after the PN. For each given AA, the relation between plasma variations at the steady-state and infusion rate, plasma clearance (Cl), renal clearance (Clr), re-absorption rate (Reab) and, retention rate (Reten) were determined. The nitrogen balance (DeltaN) was calculated during the PN period. The results are presented as means+/-sem. All plasma AA concentrations decreased during the starting period of non-protein energy intake. The plasma AA concentrations reached a steady-state within 3 h upon AA infusion, except for glycine and lysine (6 h). At the steady state, the plasma concentrations of the infused AAs were closely correlated to their infusion rate (y= -18.3+1.5x, r(2)=0.92). The plasma glutamine concentration was maintained during the PN, which indicates that the solution might stimulate the de novo synthesis of this AA. When the PN was stopped, plasma levels of the AAs decreased, most of them returning to their basal levels, or significantly below for lysine (P<0.05), alanine (P<0.05), proline (P<0.01) and glutamine (P<0.05). No volunteer showed any adverse effect during the infusion period. DeltaN was: 0.8+/-0.5 gN/10 h. Metabolic characteristics for essential AAs were: Cl<0.5 l min(-1), Clr <1.5 ml x min(-1) Reab >or= 99%, Reten >or=99% and for non-essential AAs: Cl <0.6 l x min(-1) except aspartate (2.8+/-0.3 l x min(-1)), Clr < 3 ml x min(-1) except glycine (6

  2. [Uptake of 3-methyl-3-buten-1-ol into aqueous mixed solution of sulfuric acid and hydrogen peroxide].

    PubMed

    Wang, Tian-He; Liu, Ze; Ge, Mao-Fa; Wang, Wei-Gang

    2011-12-01

    Multiphase acid-catalyzed oxidation with hydrogen peroxide (H2O2) has been suggested recently to be a potential route to SOA formation, but the kinetics and chemical mechanism of this process have not been well-known yet. In this work, the uptake of 3-methyl-3-buten-1-ol (MBO331) into aqueous mixed solutions of H2O2, and sulfuric acid (H2SO4) was performed using a rotated wetted-wall reactor coupled to a VUV single-photon ionization time of flight mass spectrometer (VUV-SPI-TOFMS). The reactive uptake coefficients (gamma) were acquired for the first time and the reaction pathways were deduced according to products information. The uptake of MBO331 into H2SO4/H2O2 was fast, resulting in gamma reaching 2.52 x 10(-4)-1.05 x 10(-2) for 40%-60% H2SO4. Acetaldehyde, acetone and 3-methyl-3, 4-expoxybutane-1-ol were suggested as gas-phase products in this process. 3-methyl-3,4-expoxybutane-1-ol can transform into polyhydroxy compounds while the further reactions of the carbonyl products can occur in acidic solution, which may play a role in SOA formation. Thus, the heterogeneous acid-catalyzed oxidation of MBO331 with H2O2 might be a significant contributor to SOA loading.

  3. Uptake of formaldehyde by sulfuric acid solutions - Impact on stratospheric ozone

    NASA Technical Reports Server (NTRS)

    Tolbert, Margaret A.; Pfaff, Jeanne; Jayaweera, Indira; Prather, Michael J.

    1993-01-01

    The study investigates the uptake of CH2O by low temperature sulfuric acid solutions representative of global stratospheric particulate. It is argued that if similar uptake occurs under stratospheric pressures of CH2O, i.e., 1000 times lower than used in the present study, then the removal of CH2O from the gas phase can take away a significant source of odd hydrogen in the mid- and high-latitude lower stratosphere. It is shown that with the inclusion of this reaction, concentrations of OH and H2O are reduced by as much as 4 percent under background levels of aerosols and more than 15 percent under elevated (volcanic) conditions. The accumulation of CH2O in stratospheric aerosols over a season, reaching about 1 M solutions, will alter the composition and may even change the reactivity of these sulfuric acid-water mixtures.

  4. Separation of glycols from dilute aqueous solutions via complexation with boronic acids

    SciTech Connect

    Randel, L.A.; King, C.J.

    1991-07-01

    This work examines methods of separating low molecular weight glycols from dilute aqueous solution. Extraction into conventional solvents is generally not economical, since, in the literature reviewed, distribution ratios for the two- to four-carbon glycols are all less than one. Distribution ratios can be increased, however, by incorporating into the organic phase an extracting agent that will complex with the solute of interest. The extracting agent investigated in this work is 3-nitrophenylboronic acid (NPBA). NPBA, a boric acid derivative, reversibly complexes with many glycols. The literature on complexation of borate and related compounds with glycols, including mechanistic data, measurement techniques, and applications to separation processes, provides information valuable for designing experiments with NPBA and is reviewed herein. 88 refs., 15 figs., 24 tabs.

  5. Acidity and hydrogen exchange dynamics of iron(II)-bound nitroxyl in aqueous solution.

    PubMed

    Gao, Yin; Toubaei, Abouzar; Kong, Xianqi; Wu, Gang

    2014-10-20

    Nitroxyl-iron(II) (HNO-Fe(II)) complexes are often unstable in aqueous solution, thus making them very difficult to study. Consequently, many fundamental chemical properties of Fe(II)-bound HNO have remained unknown. Using a comprehensive multinuclear ((1)H, (15)N, (17)O) NMR approach, the acidity of the Fe(II)-bound HNO in [Fe(CN)5(HNO)](3-) was investigated and its pK(a) value was determined to be greater than 11. Additionally, HNO undergoes rapid hydrogen exchange with water in aqueous solution and this exchange process is catalyzed by both acid and base. The hydrogen exchange dynamics for the Fe(II)-bound HNO have been characterized and the obtained benchmark values, when combined with the literature data on proteins, reveal that the rate of hydrogen exchange for the Fe(II)-bound HNO in the interior of globin proteins is reduced by a factor of 10(6). PMID:25205463

  6. Dynamics of organic and inorganic arsenic in the solution phase of an acidic fen in Germany

    NASA Astrophysics Data System (ADS)

    Huang, J.-H.; Matzner, E.

    2006-04-01

    Wetland soils play a key role for the transformation of heavy metals in forested watersheds, influencing their mobility, and ecotoxicity. Our goal was to investigate the mechanisms of release from solid to solution phase, the mobility, and the transformation of arsenic species in a fen soil. In methanol-water extracts, monomethylarsonic acid, dimethylarsinic acid, trimethylarsine oxide, arsenobetaine, and two unknown organic arsenic species were found with concentrations up to 14 ng As g -1 at the surface horizon. Arsenate is the dominant species at the 0-30 cm depth, whereas arsenite predominated at the 30-70 cm depth. Only up to 2.2% of total arsenic in fen was extractable with methanol-water. In porewaters, depth gradient spatial variation of arsenic species, pH, redox potentials, and the other chemical parameters along the profile was observed in June together with high proportion of organic arsenic species (up to 1.2 μg As L -1, 70% of total arsenic). Tetramethylarsonium ion and an unknown organic arsenic species were additionally detected in porewaters at deeper horizons. In comparison, the arsenic speciation in porewaters in April was homogeneous with depth and no organic arsenic species were found. Thus, the occurrence of microbial methylation of arsenic in fen was demonstrated for the first time. The 10 times elevated total arsenic concentrations in porewaters in June compared to April were accompanied by elevated concentrations of total iron, lower concentrations of sulfate and the presence of ammonium and phosphate. The low proportion of methanol-water extractable total arsenic suggests a generally low mobility of arsenic in fen soils. The release of arsenic from solid to solution phases in fen is dominantly controlled by dissolution of iron oxides, redox transformation, and methylation of arsenic, driven by microbial activity in the growing season. As a result, increased concentrations of total arsenic and potentially toxic arsenic species in fen

  7. Chemical durability of glaze on Zsolnay architectural ceramics (Budapest, Hungary) in acid solutions

    NASA Astrophysics Data System (ADS)

    Baricza, Ágnes; Bajnóczi, Bernadett; May, Zoltán; Tóth, Mária; Szabó, Csaba

    2015-04-01

    Zsolnay glazed architectural ceramics are among the most famous Hungarian ceramics, however, there is no profound knowledge about the deterioration of these building materials. The present study aims to reveal the influence of acidic solutions in the deterioration of Zsolnay ceramics. The studied ceramics are glazed roof tiles, which originate from two buildings in Budapest: one is located in the densely built-up city centre with high traffic rate and another one is in a city quarter with moderate traffic and more open space. The roof tiles represent the construction and the renovation periods of the buildings. The ceramics were mainly covered by lead glazes in the construction period and mainly alkali glazes in the renovation periods. The glaze of the tiles were coloured with iron (for yellow glaze) or chromium/copper/iron (for green glazes) in the case of the building located in the city centre, whereas cobalt was used as colorant and tin oxide as opacifier for the blue glaze of the ceramics of the other building. Six tiles were selected from each building. Sulphuric acid (H2SO4) solutions of pH2 and pH4 were used to measure the durability of the glazes up to 14 days at room temperature. The surfaces of the glazed ceramics after the treatment were measured by X-ray diffraction, Raman spectroscopy and SEM-EDS techniques to determine the precipitated phases on the surface of the glaze. Electron microprobe analysis was used to quantitatively characterise phases found and to determine the chemical composition of the treated glaze. The recovered sulphuric acid solutions were measured with ICP-OES technique in order to quantify the extent of the ion exchange between the glaze and the solutions. There is a significant difference in the dissolution rates in the treatments with sulphuric acid solutions of pH2 and pH4, respectively. The solution of pH2 induced greater ion exchange (approx. 7-10 times) from the glaze compared to the solution of pH4. Alkali and alkali earth

  8. Results of Analysis of Macrobatch 3 Decontaminated Salt Solution Coalescer from May 2010

    SciTech Connect

    Peters, T. B.; Fink, S. D.

    2012-12-18

    SRNL analyzed the Decontamination Salt Solution (DSS) coalescer from MCU by several analytical methods. This unit was removed from service in May 2010. The results of these analyses indicate that there is very little evidence of fouling via excessive solids, either from the leaching studies or X-Ray Diffraction (XRD) analysis.

  9. Enhanced capacity of chitosan for transition-metal ions in sulphate-sulphuric acid solutions.

    PubMed

    Muzzarelli, R A; Rocchetti, R

    1974-11-01

    Batch measurements have shown that the collection yields of chitosan for chromium(III), iron(III), nickel, copper(II), zinc and mercury(II) from sulphuric acid solutions are higher when the solutions contain ammonium sulphate, or when chitosan conditioned in ammonium sulphate is used, particularly at pH 3.0 and 5.0. The contrary is verified for the oxy-anions vanadate, chromate and molybdate. Manganese is never collected. At pH 1.0 no collection occurs. A procedure for recycling chromatographic columns includes fixation of Cu or Ni from a sulphate solution at pH 3-5 on sulphate-conditioned chitosan, and elution with 0.1M sulphuric acid/0.1M ammonium sulphate at pH 1.0; the presence of sulphate in the eluent obviates the detrimental effect of sulphuric acid on the next cycle. Sulphate is the favoured counter-ion of the chelated cations and its action produces shorter chromatographic bands. The interaction of sulphate with chitosan is discussed in terms of crystallinity and steric distribution of the protonated amino-groups in the polymer. Data on the new diethylaminohydroxypropylcellulose are included. PMID:18961577

  10. Pharmacological manipulation of arachidonic acid-epoxygenase results in divergent effects on renal damage.

    PubMed

    Li, Jing; Stier, Charles T; Chander, Praveen N; Manthati, Vijay L; Falck, John R; Carroll, Mairéad A

    2014-01-01

    Kidney damage is markedly accelerated by high-salt (HS) intake in stroke-prone spontaneously hypertensive rats (SHRSP). Epoxyeicosatrienoic acids (EETs) are epoxygenase products of arachidonic acid which possess vasodepressor, natriuretic, and anti-inflammatory activities. We examined whether up-regulation (clofibrate) or inhibition [N-methylsulfonyl-6-(2-propargyloxyphenyl)hexanamide (MS-PPOH)] of epoxygenase would alter systolic blood pressure (SBP) and/or renal pathology in SHRSP on HS intake (1% NaCl drinking solution). Three weeks of treatment with clofibrate induced renal cortical protein expression of CYP2C23 and increased urinary excretion of EETs compared with vehicle-treated SHRSP. SBP and urinary protein excretion (UPE) were significantly lowered with clofibrate treatment. Kidneys from vehicle-treated SHRSP, which were on HS intake for 3 weeks, demonstrated focal lesions of vascular fibrinoid degeneration, which were markedly attenuated with clofibrate treatment. In contrast, 2 weeks of treatment with the selective epoxygenase inhibitor, MS-PPOH, increased UPE without significantly altering neither urinary EET levels nor SBP. Kidneys from vehicle-treated SHRSP, which were on HS intake for 11 days, demonstrated occasional mild damage whereas kidneys from MS-PPOH-treated rats exhibited widespread malignant nephrosclerosis. These results suggest that pharmacological manipulation of epoxygenase results in divergent effects on renal damage and that interventions to increase EET levels may provide therapeutic strategies for treating salt-sensitive hypertension and renal damage.

  11. Adsorption of naphthalene from aqueous solution onto fatty acid modified walnut shells.

    PubMed

    Zhu, Mijia; Yao, Jun; Dong, Lifu; Sun, Jingjing

    2016-02-01

    The removal of polycyclic aromatic hydrocarbons (PAHs) from aqueous solution is challenging to environmental technologists. Agricultural waste is apparently the most attractive materials in removing PAHs because of its abundance, renewability, and economic advantage. The adsorption of PAHs (e.g., naphthalene) onto walnut shell (WNS) and its fatty acid (e.g., capric acid, lauric acid, palmitic acid, and oleic acid)-modified equivalent were investigated in this work to develop low-cost biosorbents for hydrophobic organic compounds. Compared with other modified sorbents, oleic acid graftted walnut shell (OWNS) showed the maximum partition coefficient (4330 ± 8.8 L kg(-1)) because of its lowest polarity and highest aromaticity. The adsorption capacity (7210 μg g(-1)) of OWNS at the temperature of 298 K was observed for an initial naphthalene concentration of 25 mg L(-1) with contact time of 40 h, sorbent dosage of 1 g L(-1), and in neutral condition. Furthermore, the regeneration capability of OWNS implied that it was a promising biosorbent for naphthalene removal.

  12. Adsorption of naphthalene from aqueous solution onto fatty acid modified walnut shells.

    PubMed

    Zhu, Mijia; Yao, Jun; Dong, Lifu; Sun, Jingjing

    2016-02-01

    The removal of polycyclic aromatic hydrocarbons (PAHs) from aqueous solution is challenging to environmental technologists. Agricultural waste is apparently the most attractive materials in removing PAHs because of its abundance, renewability, and economic advantage. The adsorption of PAHs (e.g., naphthalene) onto walnut shell (WNS) and its fatty acid (e.g., capric acid, lauric acid, palmitic acid, and oleic acid)-modified equivalent were investigated in this work to develop low-cost biosorbents for hydrophobic organic compounds. Compared with other modified sorbents, oleic acid graftted walnut shell (OWNS) showed the maximum partition coefficient (4330 ± 8.8 L kg(-1)) because of its lowest polarity and highest aromaticity. The adsorption capacity (7210 μg g(-1)) of OWNS at the temperature of 298 K was observed for an initial naphthalene concentration of 25 mg L(-1) with contact time of 40 h, sorbent dosage of 1 g L(-1), and in neutral condition. Furthermore, the regeneration capability of OWNS implied that it was a promising biosorbent for naphthalene removal. PMID:26517393

  13. Adsorption of Acid Red 57 from aqueous solutions onto surfactant-modified sepiolite.

    PubMed

    Ozcan, Adnan; Ozcan, A Safa

    2005-10-17

    The adsorption of Acid Red 57 (AR57) onto surfactant-modified sepiolite was investigated in aqueous solution in a batch system with respect to contact time, pH and temperature. The surface modification of surfactant-modified sepiolite was controlled using the FTIR technique. The pseudo-first-order, pseudo-second-order kinetic models and the intraparticle diffusion model were used to describe the kinetic data and the rate constants were evaluated. The experimental data fitted very well the pseudo-second-order kinetic model and also followed the intraparticle diffusion model up to 90 min, whereas diffusion is not only the rate controlling step. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were also determined. The Freundlich model agrees with experimental data well. The activation energy, change of free energy, enthalpy and entropy of adsorption were also evaluated for the adsorption of AR57 onto surfactant-modified sepiolite. The results indicate that surfactant-modified sepiolite could be employed as low-cost material for the removal of textile dyes from effluents. PMID:16019142

  14. Oxidation of FeS by oxygen-bearing acidic solutions.

    PubMed

    Chiriţă, Paul; Descostes, Michaël; Schlegel, Michel L

    2008-05-01

    Oxidation of FeS in oxygen-bearing acidic solutions was investigated at different temperatures (25 to 45 degrees C) and pH (2.75 to 3.45). The rate of the oxidative dissolution of FeS is strongly dependent on pH. The reaction order with respect to hydrogen ions has been found to be 1.03+/-0.02 at 25 degrees C, and the apparent activation energy (E(a)) is 41.6 +/- 10.7 kJ mol(-1) at initial pH 3.00, suggesting that the FeS oxidative dissolution is controlled by the diffusion of oxidant species across a sulfur-rich layer (SRL) that undergoes chemical transformations leading to an increase in the mean number of sulfur atoms in polysulfide chains and the rearrangement of these chains. Fourier transform infrared spectroscopy and X-ray diffraction results obtained for the FeS samples reacted for 72 h at 25 degrees C and pH between 2.75 and 3.45 indicate the formation of goethite, of lepidocrocite, and of poorly ordered solid phases (assigned as SRL) on initial surfaces. The experimental data suggest a mechanism based on the protonation of FeS surfaces followed by oxidation of FeS by dissolved oxygen to produce Fe(2+), S(0), and S(2-)(n). Fe(2+) is unstable under oxidative conditions and transforms into Fe(OH)(3(s)), goethite and lepidocrocite.

  15. Corrosion inhibition of a mild steel by aniline and alkylamines in acidic solutions

    SciTech Connect

    Luo, H.; Han, K.N.; Guan, Y.C.

    1998-09-01

    Corrosion inhibition of a mild steel in acid solutions by alkylamines (ALK-AM) and aniline hydrochloric (ANL-HCl) salts was investigated in the presence of sodium sulfate (Na{sub 2}SO{sub 4}) and sodium chloride (NaCl) using a potentiostat, a contact-angle goniometer, a scanning electron microscope (SEM), a Fourier transform infrared spectrometer (FTIR), and an atomic force microscope (AFM). Results showed chloride ions (Cl{sup {minus}}) had a pronounced effect on inhibition of amines and ANL for corrosion of mild steel. In the presence of Cl{sup {minus}} ions, cationic types of surfactants (ALK-AM and ANL) were attached to the surface through formation of chloride precipitate at the surface. In the absence of the organic inhibitors, corrosion initiated along grain boundaries of ferrite and pearlite structures. In the presence of the organic inhibitor, however, the steel surface was covered by an organic salt precipitation, and the corrosion rate was reduced significantly.

  16. Quantitative rRNA-targeted solution-based hybridization assay using peptide nucleic acid molecular beacons.

    PubMed

    Li, Xu; Morgenroth, Eberhard; Raskin, Lutgarde

    2008-12-01

    The potential of a solution-based hybridization assay using peptide nucleic acid (PNA) molecular beacon (MB) probes to quantify 16S rRNA of specific populations in RNA extracts of environmental samples was evaluated by designing PNA MB probes for the genera Dechloromonas and Dechlorosoma. In a kinetic study with 16S rRNA from pure cultures, the hybridization of PNA MB to target 16S rRNA exhibited a higher final hybridization signal and a lower apparent rate constant than the hybridizations to nontarget 16S rRNAs. A concentration of 10 mM NaCl in the hybridization buffer was found to be optimal for maximizing the difference between final hybridization signals from target and nontarget 16S rRNAs. Hybridization temperatures and formamide concentrations in hybridization buffers were optimized to minimize signals from hybridizations of PNA MB to nontarget 16S rRNAs. The detection limit of the PNA MB hybridization assay was determined to be 1.6 nM of 16S rRNA. To establish proof for the application of PNA MB hybridization assays in complex systems, target 16S rRNA from Dechlorosoma suillum was spiked at different levels to RNA isolated from an environmental (bioreactor) sample, and the PNA MB assay enabled effective quantification of the D. suillum RNA in this complex mixture. For another environmental sample, the quantitative results from the PNA MB hybridization assay were compared with those from clone libraries.

  17. RESULTS OF ANALYSES OF MACROBATCH 3 DECONTAMINATED SALT SOLUTION (DSS) COALESCER AND PRE-FILTERS

    SciTech Connect

    Peters, T.; Fondeur, F.; Fink, S.

    2012-06-13

    SRNL analyzed the pre-filter and Decontamination Salt Solution (DSS) coalescer from MCU by several analytical methods. The results of these analyses indicate that overall there is light to moderate solids fouling of both the coalescer and pre-filter elements. The majority of the solids contain aluminum, sodium, silicon, and titanium, in oxide and/or hydroxide forms that we have noted before. The titanium is presumably precipitated from leached, dissolved monosodium titanate (MST) or fines from MST at ARP, and the quantity we find is significantly greater than in the past. A parallel report discusses potential causes for the increased leaching rate of MST, showing that increases in free hydroxide concentration of the feed solutions and of chemical cleaning solutions lead to faster leaching of titanium.

  18. Differential proteomics to explore the inhibitory effects of acidic, slightly acidic electrolysed water and sodium hypochlorite solution on Vibrio parahaemolyticus.

    PubMed

    Chen, Tai-Yuan; Kuo, Shu-Hao; Chen, Shui-Tein; Hwang, Deng-Fwu

    2016-03-01

    Slightly acidic electrolysed water (SlAEW) and acidic electrolysed water (AEW) have been demonstrated to effectively inactivate food-borne pathogens. However, the underlying mechanism of inactivation remains unknown. Therefore, in this study, a differential proteomic platform was used to investigate the bactericidal mechanism of SlAEW, AEW, and sodium hypochlorite (NaOCl) solutions against Vibrio parahaemolyticus. The upregulated proteins after SlAEW, AEW, and NaOCl treatments were identified as outer membrane proteins K and U. The downregulated proteins after the SlAEW, AEW, and NaOCl treatments were identified as adenylate kinase, phosphoglycerate kinase, glyceraldehyde-3-phosphate dehydrogenase (GAPDH), and enolase, all of which are responsible for energy metabolism. Protein synthesis-associated proteins were downregulated and identified as elongation factor Tu and GAPDH. The inhibitory effects of SlAEW and AEW solutions against V. parahaemolyticus may be attributed to the changes in cell membrane permeability, protein synthesis activity, and adenosine triphosphate (ATP) biosynthesis pathways such as glycolysis and ATP replenishment.

  19. Effect of citric acid and bacteria on metal uptake in reeds grown in a synthetic acid mine drainage solution.

    PubMed

    Guo, Lin; Cutright, Teresa J

    2015-03-01

    The effect of citric acid (CA), rhizosphere acidophilic heterotrophs and/or Fe(II) oxidizing bacteria (Fe(II)OB) on plaque formation and metal accumulation in Phragmites australis L. (common reed) from acid mine drainage (AMD) solution were investigated. Reeds were grown in different hydroponic solutions that contained AMD, CA and/or rhizosphere bacteria for three months. Triplicate experiments were conducted for each experimental condition. Fe(II)OB enhanced the formation of Fe plaque which decreased Fe and Mn uptake in reeds, while it had no significant influence on Al accumulation. CA inhibited the growth of Fe(II)OB, decreased the formation of metal plaque and increased Fe and Mn accumulation in reeds. Acidophilic heterotrophs consumed CA and made the environment more suitable for the growth of Fe(II)OB. Reeds are a good candidate for phytoextraction while CA is a useful chelator to enhance metal uptake in plants. More research may be needed to investigate the influence of CA on microbial community. Further investigations are required to study the effect of CA on phytoremediation of AMD contaminated fields.

  20. Differential proteomics to explore the inhibitory effects of acidic, slightly acidic electrolysed water and sodium hypochlorite solution on Vibrio parahaemolyticus.

    PubMed

    Chen, Tai-Yuan; Kuo, Shu-Hao; Chen, Shui-Tein; Hwang, Deng-Fwu

    2016-03-01

    Slightly acidic electrolysed water (SlAEW) and acidic electrolysed water (AEW) have been demonstrated to effectively inactivate food-borne pathogens. However, the underlying mechanism of inactivation remains unknown. Therefore, in this study, a differential proteomic platform was used to investigate the bactericidal mechanism of SlAEW, AEW, and sodium hypochlorite (NaOCl) solutions against Vibrio parahaemolyticus. The upregulated proteins after SlAEW, AEW, and NaOCl treatments were identified as outer membrane proteins K and U. The downregulated proteins after the SlAEW, AEW, and NaOCl treatments were identified as adenylate kinase, phosphoglycerate kinase, glyceraldehyde-3-phosphate dehydrogenase (GAPDH), and enolase, all of which are responsible for energy metabolism. Protein synthesis-associated proteins were downregulated and identified as elongation factor Tu and GAPDH. The inhibitory effects of SlAEW and AEW solutions against V. parahaemolyticus may be attributed to the changes in cell membrane permeability, protein synthesis activity, and adenosine triphosphate (ATP) biosynthesis pathways such as glycolysis and ATP replenishment. PMID:26471589

  1. Method for extracting lanthanides and actinides from acid solutions by modification of Purex solvent

    DOEpatents

    Horwitz, E.P.; Kalina, D.G.

    1986-03-04

    A process is described for the recovery of actinide and lanthanide values from aqueous solutions with an extraction solution containing an organic extractant having the formula as shown in a diagram where [phi] is phenyl, R[sup 1] is a straight or branched alkyl or alkoxyalkyl containing from 6 to 12 carbon atoms and R[sup 2] is an alkyl containing from 3 to 6 carbon atoms and phase modifiers in a water-immiscible hydrocarbon diluent. The addition of the extractant to the Purex process extractant, tri-n-butylphosphate in normal paraffin hydrocarbon diluent, will permit the extraction of multivalent lanthanide and actinide values from 0.1 to 12.0 molar acid solutions. 6 figs.

  2. Aqueous solutions of acidic ionic liquids for enhanced stability of polyoxometalate-carbon supercapacitor electrodes

    NASA Astrophysics Data System (ADS)

    Hu, Chenchen; Zhao, Enbo; Nitta, Naoki; Magasinski, Alexandre; Berdichevsky, Gene; Yushin, Gleb

    2016-09-01

    Nanocomposites based on polyoxometalates (POMs) nanoconfined in microporous carbons have been synthesized and used as electrodes for supercapacitors. The addition of the pseudocapacitance from highly reversible redox reaction of POMs to the electric double-layer capacitance of carbon lead to an increase in specific capacitance of ∼90% at 1 mV s-1. However, high solubility of POM in traditional aqueous electrolytes leads to rapid capacity fading. Here we demonstrate that the use of aqueous solutions of protic ionic liquids (P-IL) as electrolyte instead of aqueous sulfuric acid solutions offers an opportunity to significantly improve POM cycling stability. Virtually no degradation in capacitance was observed in POM-based positive electrode after 10,000 cycles in an asymmetric capacitor with P-IL aqueous electrolyte. As such, POM-based carbon composites may now present a viable solution for enhancing energy density of electrical double layer capacitors (EDLC) based on pure carbon electrodes.

  3. Corrosion of some chromium-nickel steels and alloys in sulfuric acid solutions of sodium sulfite

    SciTech Connect

    Kopeliovich, D.K.; Glagolenko, Yu.V.; Ermolinskii, S.P.

    1988-05-01

    Steels 12Kh18N1OT and 10Kh17N13M3T and alloys 06KhN28MDT and 46KhNM were studied in sulfuric acid solutions containing sodium sulfite and sulfur dioxide to determine the effects of different concentrations of the corrosive constituents on the anodic and cathodic active and passive corrosion behavior of the metals. Polarization curves were obtained with a P-5827 M potentiostat. Addition of sulfite facilitated both electrode processes and the region of the reactive state was broadened due to the shift of passivation potentials to more positive values. The activating effect of sulfite reduction products were confirmed by tests of alloys in spent solutions. This increased likelihood of activation and the decrease of the solutions's own corrosion potential were both attributed to retardation of the cathodic process by lower valence sulfur compounds.

  4. Method for extracting lanthanides and actinides from acid solutions by modification of purex solvent

    DOEpatents

    Horwitz, E. Philip; Kalina, Dale G.

    1986-01-01

    A process for the recovery of actinide and lanthanide values from aqueous solutions with an extraction solution containing an organic extractant having the formula: ##STR1## where .phi. is phenyl, R.sup.1 is a straight or branched alkyl or alkoxyalkyl containing from 6 to 12 carbon atoms and R.sup.2 is an alkyl containing from 3 to 6 carbon atoms and phase modifiers in a water-immiscible hydrocarbon diluent. The addition of the extractant to the Purex process extractant, tri-n-butylphosphate in normal paraffin hydrocarbon diluent, will permit the extraction of multivalent lanthanide and actinide values from 0.1 to 12.0 molar acid solutions.

  5. Thermosensitivity of bile acid-based oligo(ethylene glycol) stars in aqueous solutions.

    PubMed

    Strandman, Satu; Le Dévédec, Frantz; Zhu, X X

    2011-08-01

    Amphiphilic star-shaped oligo(ethylene glycol)s with a hydrophobic bile acid core and varying number of hydrophilic arms have been made. Their thermal behavior in aqueous solutions depends on the number rather than the length of the arms. The two-armed lithocholate derivative showed the strongest tendency for association and exhibited the lowest cloud point (79 °C) of the oligomers made, as well as another phase separation at a lower temperature (31 °C). The "double thermosensitivity" arising both from the salt-dependent LCST of the oligo(ethylene glycol) segments and the temperature-responsive self-assembly of amphiphilic bile acid derivative provides an interesting path in the design of bile acid-based smart materials.

  6. Thermosensitivity of bile acid-based oligo(ethylene glycol) stars in aqueous solutions.

    PubMed

    Strandman, Satu; Le Dévédec, Frantz; Zhu, X X

    2011-08-01

    Amphiphilic star-shaped oligo(ethylene glycol)s with a hydrophobic bile acid core and varying number of hydrophilic arms have been made. Their thermal behavior in aqueous solutions depends on the number rather than the length of the arms. The two-armed lithocholate derivative showed the strongest tendency for association and exhibited the lowest cloud point (79 °C) of the oligomers made, as well as another phase separation at a lower temperature (31 °C). The "double thermosensitivity" arising both from the salt-dependent LCST of the oligo(ethylene glycol) segments and the temperature-responsive self-assembly of amphiphilic bile acid derivative provides an interesting path in the design of bile acid-based smart materials. PMID:21661073

  7. Self-assembled polyaniline nanotubes grown from a polymeric acid solution

    NASA Astrophysics Data System (ADS)

    Zhang, Lijuan; Peng, Hui; Hsu, Chyong Fang; Kilmartin, Paul A.; Travas-Sejdic, Jadranka

    2007-03-01

    Polyaniline (PANI) nanotubes were obtained by a self-assembly process, from a solution containing poly(methyl vinyl ether-alt-maleic acid) (PMVEA) by oxidative polymerization using ammonium persulfate as the oxidant. The size of the nanotubes was greatly affected by the weight ratio of polymeric acid to aniline as measured by SEM images. The outer diameter of the nanotubes increased from 65 to 160 nm as the weight ratio of PMVEA to aniline increased from 1 to 4 wt/wt%. The structural features of the nanotubes were characterized by FTIR, XPS and EPR spectroscopies, which confirmed the presence of the polymeric acid in the PANI nanotubes and their electronic conductive nature. The electrochemical properties were further analysed using cyclic voltammetry.

  8. p-Aminophenylacetic acid-mediated synthesis of monodispersed titanium oxide hybrid microspheres in ethanol solution.

    PubMed

    Zhang, Hongye; Xie, Yun; Liu, Zhimin; Tao, Ranting; Sun, Zhenyu; Ding, Kunlun; An, Guimin

    2009-10-15

    Monodispersed TiO2 hybrid microspheres were prepared via the hydrolysis of titanium isopropoxide (TTIP) in ethanol solution containing p-aminophenylacetic acid (APA). The effects of the APA:TTIP molar ratio, water content, reaction time and reaction temperature on the morphology of the resultant spheres were investigated. The products were characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and X-ray diffraction. It was demonstrated that the diameters of the resultant TiO2 spheres could be tuned in the range of 380-800 nm by changing the APA:TTIP molar ratio (1:3 to 3:1) and water content (1-3 v/v%) in the reaction medium, and that increasing the APA:TTIP molar ratio led to larger TiO2 hybrid spheres while increasing the water content decreased their size. The loading content of APA in the hybrid spheres could reach 20 wt.% as they were prepared with the APA:TTIP ratio of 3:1. The possible formation mechanism of the hybrid spheres was also investigated. It was found that APA slowed down the hydrolysis rate of the titanium precursor so that resulted in the formation of the TiO2 spheres. In addition, the APA present in TiO2 spheres acted as a reducing agent to in situ convert HAuCl4 into metallic Au on the surface of the TiO2 spheres. The catalytic activity of the resultant Au/APA-TiO2 composite was examined using transfer hydrogenation of phenylacetone with 2-propanol, and it was indicated that the catalyst displayed high efficiency for this reaction. PMID:19616218

  9. A systematic investigation and insight into the formation mechanism of bilayers of fatty acid/soap mixtures in aqueous solutions.

    PubMed

    Xu, Wenlong; Song, Aixin; Dong, Shuli; Chen, Jingfei; Hao, Jingcheng

    2013-10-01

    Vesicles are the most common form of bilayer structures in fatty acid/soap mixtures in aqueous solutions; however, a peculiar bilayer structure called a "planar sheet" was found for the first time in the mixtures. In the past few decades, considerable research has focused on the formation theory of bilayers in fatty acid/soap mixtures. The hydrogen bond theory has been widely accepted by scientists to explain the formation of bilayers. However, except for the hydrogen bond, no other driving forces were proposed systematically. In this work, three kinds of weak interactions were investigated in detail, which could perfectly demonstrate the formation mechanism of bilayer structures in the fatty acid/soap mixtures in aqueous solutions. (i) The influence of hydrophobic interaction was detected by changing the chain length of fatty acid (C(n)H(2n+1)COOH), in which n = 10 to 18, the phase behavior was investigated, and the phase region was presented. With the help of cryogenic transmission electron microscopy (cryo-TEM) observations, deuterium nuclear magnetic resonance ((2)H NMR), and X-ray diffraction (XRD) measurements, the vesicles and planar sheets were determined. The chain length of C(n)H(2n+1)COOH has an important effect on the physical state of the hydrophobic chain, resulting in an obvious difference in the viscoelasticity of the solution samples. (ii) The existence of hydrogen bonds between fatty acids and their soaps in aqueous solutions was demonstrated by Fourier transform infrared (FT-IR) spectroscopy and molecule dynamical simulation. From the pH measurements, the pH ranges of the bilayer formation were at the pKa values of fatty acids, respectively. (iii) Counterions can be embedded in the stern layer of the bilayers and screen the electrostatic repulsion between the COO(-) anionic headgroups. FT-IR characterization demonstrated a bidentate bridging coordination mode between counterions and carboxylates. The conductivity measurements provided the degree

  10. Densities of L-Glutamic Acid HCl Drug in Aqueous NaCl and KCl Solutions at Different Temperatures

    NASA Astrophysics Data System (ADS)

    Ryshetti, Suresh; Raghuram, Noothi; Rani, Emmadi Jayanthi; Tangeda, Savitha Jyostna

    2016-04-01

    Densities (ρ ) of (0.01 to 0.07) {mol}{\\cdot } {kg}^{-1} L-Glutamic acid HCl (L-HCl) drug in water, and in aqueous NaCl and KCl (0.5 and 1.0) {mol}{\\cdot } {kg}^{-1} solutions have been reported as a function of temperature at T = (298.15, 303.15, 308.15, and 313.15) K and atmospheric pressure. The accurate density (ρ ) values are used to estimate the various parameters such as the apparent molar volume (V_{2,{\\upphi }}), the partial molar volume (V2^{∞}), the isobaric thermal expansion coefficient (α 2), the partial molar expansion (E2^{∞}), and Hepler's constant (partial 2V2^{∞}/partial T2)P. The Cosphere overlap model is used to understand the solute-solvent interactions in a ternary mixture (L-HCl drug + NaCl or KCl + water). Hepler's constant (partial 2V2^{∞}/partial T2)_P is utilized to interpret the structure-making or -breaking ability of L-HCl drug in aqueous NaCl and KCl solutions, and the results are inferred that L-HCl drug acts as a structure maker, i.e., kosmotrope in aqueous NaCl solutions and performs as a structure breaker, i.e., chaotrope in aqueous KCl solutions.

  11. In-situ spectroscopic investigations of the redox behavior of poly(indole-5-carboxylic-acid) modified electrodes in acidic aqueous solutions.

    PubMed

    Talbi, H; Billaud, D; Louarn, G; Pron, A

    2001-03-01

    The oxidation of electrochemically grown poly(indole-5-carboxylic-acid) (P5CO2H) and its spectroscopic properties have been studied by in-situ spectroelectrochemical techniques. The purpose of this paper is to characterize the different modifications on the P5CO2H backbone, induced by the electrochemical oxidation in aqueous acidic solution. We have identified, on the basis of Raman spectra, the vibrational modes associated with neutral and oxidized segments of polymer. It was shown that at least three chemically and optically different species (perhaps other products too) are produced in different potential regimes upon oxidation of this polymer. The results obtained also indicate that the molecular properties of this conducting polymer are better revealed by in-situ resonant spectra than by ex-situ infrared and Raman studies.

  12. Oxidative photodegradation of herbicide fenuron in aqueous solution by natural iron oxide α-Fe2O3, influence of polycarboxylic acids.

    PubMed

    Kribéche, Mohamed El Amine; Mechakra, Hind; Sehili, Tahar; Brosillon, Stephan

    2016-01-01

    The photodegradation of the herbicide fenuron (1,1-dimethyl-3-phenylurea) by using a natural iron oxide (NIO), α-Fe2O3, in aqueous solution at acidic pH has been undertaken. The NIO was characterized by the Raman spectroscopy method. The degradation pathways and the formation of degradation products were studied. A high-pressure mercury lamp and sunlight were employed as light source. Fenuron photodegradation using NIO with oxalic acid followed the pseudo-first-order kinetics, the optimal experimental conditions were [oxalic acid]0 = 10(-3) M and [NIO] = 0.1 g L(-1) at pH 3. A UVA/NIO/oxalic acid system led to a low fenuron half-life (60 min). The results were even better when solar light is used (30 min). The variables studied were the doses of iron oxide, of carboxylic acids, the solution pH and the effect of sunlight irradiation. The effects of four carboxylic acids, oxalic, citric, tartaric and malic acids, on the fenuron photodegradation with NIO have been investigated, oxalic acid was the most effective carboxylic acid used at pH 3. A similar trend was observed for the removal of total organic carbon (TOC), 75% of TOC was removed. The analytical study showed many aromatic intermediates, short-chain carboxylic acids and inorganic ion. PMID:26102217

  13. Removal of uranium(VI) from aqueous solution using iminodiacetic acid derivative functionalized SBA-15 as adsorbents.

    PubMed

    Wang, Yu-Long; Song, Li-Juan; Zhu, Lu; Guo, Bo-Long; Chen, Su-Wen; Wu, Wang-Suo

    2014-03-01

    Three different functional SBA-15 were prepared by a post-grafting method using three iminodiacetic acid derivatives of ethylenediaminetriacetic acid (ED3A), diethylenetriaminetetraacetic acid (DT4A), and 1,2-cyclohexylenedinitrilotriacetic acid (CyD3A), which were used as adsorbents for removal of uranium(vi) from aqueous solution. These materials were characterized by FT-IR, NMR, TEM, nitrogen adsorption/desorption experiments, and elemental analysis. The effect of pH, ionic strength, contact time, solid-liquid ratio, initial metal ion concentration, temperature, and coexisting ions on uranium(vi) sorption behaviors of the functionalized SBA-15 was studied. Typical sorption isotherms (Langmuir and Freundlich) were determined for the sorption process, and the maximum sorption capacity was calculated. The influence of functional groups on uranium(vi) sorption was also discussed. As a result, compared with other current U(vi) sorbents (granite, kaolin, attapulgite), SBA-15-1,2-cyclohexylenedinitrilotriacetic acid (SBA-15-CyD3A) possessed good selective sorption properties, which had potential application in separation of uranium(vi). PMID:24435450

  14. Removal of uranium(VI) from aqueous solution using iminodiacetic acid derivative functionalized SBA-15 as adsorbents.

    PubMed

    Wang, Yu-Long; Song, Li-Juan; Zhu, Lu; Guo, Bo-Long; Chen, Su-Wen; Wu, Wang-Suo

    2014-03-01

    Three different functional SBA-15 were prepared by a post-grafting method using three iminodiacetic acid derivatives of ethylenediaminetriacetic acid (ED3A), diethylenetriaminetetraacetic acid (DT4A), and 1,2-cyclohexylenedinitrilotriacetic acid (CyD3A), which were used as adsorbents for removal of uranium(vi) from aqueous solution. These materials were characterized by FT-IR, NMR, TEM, nitrogen adsorption/desorption experiments, and elemental analysis. The effect of pH, ionic strength, contact time, solid-liquid ratio, initial metal ion concentration, temperature, and coexisting ions on uranium(vi) sorption behaviors of the functionalized SBA-15 was studied. Typical sorption isotherms (Langmuir and Freundlich) were determined for the sorption process, and the maximum sorption capacity was calculated. The influence of functional groups on uranium(vi) sorption was also discussed. As a result, compared with other current U(vi) sorbents (granite, kaolin, attapulgite), SBA-15-1,2-cyclohexylenedinitrilotriacetic acid (SBA-15-CyD3A) possessed good selective sorption properties, which had potential application in separation of uranium(vi).

  15. Influence of trace elements on stabilization of aqueous solutions of ascorbic acid.

    PubMed

    Dolińska, Barbara; Ostróżka-Cieślik, Aneta; Caban, Artur; Rimantas, Klimas; Leszczyńska, Lucyna; Ryszka, Florian

    2012-12-01

    Together with vitamin C, zinc, selenium, manganese, and magnesium play a vital role in the preservation of organs scheduled for transplantation. In the present study, it is shown that addition of 1 mg/l of these elements influences the stability of 0.3 mM ascorbic acid solutions. The solution's stability was estimated using an accelerated stability test. The concentration of vitamin C was measured using a validated spectrophotometric method, which uses the reduction of 2,6-dichlorophenoloindophenol by ascorbic acid. Elevated temperatures, the factor accelerating substances' decomposition reaction rate, were used in the tests. The research was conducted at two temperatures at intervals of 10 °C: 80 ± 0.1 and 90 ± 0.1 °C. It was stated that the studied substances' decomposition occurred in accordance with the equation for first-order reactions. The function of the logarithmic concentration (log%C) over time was revealed to be rectilinear. This dependence was used to determine the kinetics of decomposition reaction rate parameters. The stabilization of vitamin C solutions was measured as the time in which 10 % of the substance decomposed at 20 and 0 °C. Addition of Se(IV) or Mg(II) ions significantly increase the stability of ascorbic acid solution (∼34 and ∼16 %, respectively), but Zn(II) causes a significant decrease in stability by ∼23 %. Addition of Mn(II) has no significant influence on vitamin C stability.

  16. 78 FR 34648 - Citric Acid and Certain Citrate Salts: Preliminary Results of Countervailing Duty Administrative...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-10

    ... International Trade Administration Citric Acid and Certain Citrate Salts: Preliminary Results of Countervailing... review of the countervailing duty (CVD) order on citric acid and citrate salts from the People's Republic... (202) 482-1503. Scope of the Order The merchandise subject to the order is citric acid and...

  17. Pulmonary clearance of three aerosolized solutes in oleic acid-induced lung injury

    SciTech Connect

    Huchon, G.J.; Montgomery, A.B.; Lipavsky, A.; Hoeffel, J.M.; Murray, J.F.

    1988-03-01

    We studied the effects of oleic acid (OA) on pulmonary clearance of three aerosolized radioactive solutes: /sup 99m/Tc-diethylenetriamine pentaacetate (/sup 99m/Tc-DTPA), /sup 67/Ga-desferoxamine (/sup 67/Ga-DFOM), and /sup 111/In-transferrin (/sup 111/In-TF). Either 0.09 ml/kg OA or an equivalent volume of 0.9% NaCl (controls) was administered intravenously to 48 anesthetized, paralyzed dogs. Each animal received one aerosolized solute either 60 min after (protocol A) or 30 min before (protocol B) the infusion of OA or NaCl. In protocol A clearances of all three solutes were similar in OA and control animals. In contrast, in protocol B clearances of all three solutes increased significantly during OA infusion; during the next 60 min clearances of /sup 99m/Tc-DTPA and /sup 67/Ga-DFOM returned to control values but 111In-TF remained increased. We conclude that 1) in OA-induced permeability edema pulmonary clearance of aerosolized solutes is increased when the aerosol is delivered 30 min before but not 60 min after injury, and 2) increased clearance persists only for large molecules, presumably because smaller molecules cross injured epithelium quickly and completely. These phenomena are best explained by a nonhomogeneous distribution of OA-induced injury.

  18. Effect of wood ash application on soil solution chemistry of tropical acid soils: incubation study.

    PubMed

    Nkana, J C Voundi; Demeyer, A; Verloo, M G

    2002-12-01

    The objective of this study was to determine the effect of wood ash application on soil solution composition of three tropical acid soils. Calcium carbonate was used as a reference amendment. Amended soils and control were incubated for 60 days. To assess soluble nutrients, saturation extracts were analysed at 15 days intervals. Wood ash application affects the soil solution chemistry in two ways, as a liming agent and as a supplier of nutrients. As a liming agent, wood ash application induced increases in soil solution pH, Ca, Mg, inorganic C, SO4 and DOC. As a supplier of elements, the increase in the soil solution pH was partly due to ligand exchange between wood ash SO4 and OH- ions. Large increases in concentrations of inorganic C, SO4, Ca and Mg with wood ash relative to lime and especially increases in K reflected the supply of these elements by wood ash. Wood ash application could represent increased availability of nutrients for the plant. However, large concentrations of basic cations, SO4 and NO3 obtained with higher application rates could be a concern because of potential solute transport to surface waters and groundwater. Wood ash must be applied at reasonable rates to avoid any risk for the environment. PMID:12365502

  19. Investigating the Influence of Polymers on Supersaturated Flufenamic Acid Cocrystal Solutions.

    PubMed

    Guo, Minshan; Wang, Ke; Hamill, Noel; Lorimer, Keith; Li, Mingzhong

    2016-09-01

    The development of enabling formulations is a key stage when demonstrating the effectiveness of pharmaceutical cocrystals to maximize the oral bioavailability for poorly water soluble drugs. Inhibition of drug crystallization from a supersaturated cocrystal solution through a fundamental understanding of the nucleation and crystal growth is important. In this study, the influence of the three polymers of polyethylene glycol (PEG), polyvinylpyrrolidone (PVP), and a copolymer of N-vinly-2-pyrrodidone (60%) and vinyl acetate (40%) (PVP-VA) on the flufenamic acid (FFA) crystallization from three different supersaturated solutions of the pure FFA and two cocrystals of FFA-NIC CO and FFA-TP CO has been investigated by measuring nucleation induction times and desupersaturation rates in the presence and absence of seed crystals. It was found that the competition of intermolecular hydrogen bonding among drug/coformer, drug/polymer, and coformer/polymer was a key factor responsible for maintaining supersaturation through nucleation inhibition and crystal growth modification in a cocrystal solution. The supersaturated cocrystal solutions with predissolved PEG demonstrated more effective stabilization in comparison to the pure FFA in the presence of the same polymer. In contrast, neither of the two cocrystal solutions, in the presence of PVP or PVP-VA, exhibited a better performance than the pure FFA with the same predissolved polymer. The study suggests that the selection of a polymeric excipient in a cocrystal formulation should not be solely dependent on the interplay of the parent drug and polymer without considering the coformer effects. PMID:27494289

  20. Longitudinal-relaxation-enhanced NMR experiments for the study of nucleic acids in solution.

    PubMed

    Farjon, Jonathan; Boisbouvier, Jérôme; Schanda, Paul; Pardi, Arthur; Simorre, Jean-Pierre; Brutscher, Bernhard

    2009-06-24

    Atomic-resolution information on the structure and dynamics of nucleic acids is essential for a better understanding of the mechanistic basis of many cellular processes. NMR spectroscopy is a powerful method for studying the structure and dynamics of nucleic acids; however, solution NMR studies are currently limited to relatively small nucleic acids at high concentrations. Thus, technological and methodological improvements that increase the experimental sensitivity and spectral resolution of NMR spectroscopy are required for studies of larger nucleic acids or protein-nucleic acid complexes. Here we introduce a series of imino-proton-detected NMR experiments that yield an over 2-fold increase in sensitivity compared to conventional pulse schemes. These methods can be applied to the detection of base pair interactions, RNA-ligand titration experiments, measurement of residual dipolar (15)N-(1)H couplings, and direct measurements of conformational transitions. These NMR experiments employ longitudinal spin relaxation enhancement techniques that have proven useful in protein NMR spectroscopy. The performance of these new experiments is demonstrated for a 10 kDa TAR-TAR*(GA) RNA kissing complex and a 26 kDa tRNA.

  1. Solubility of HOBr in Acidic Solution and Implications for Liberation of Halogens Via Aerosol Processing

    NASA Technical Reports Server (NTRS)

    Iraci, Laura T.; Michelsen, R. R.; Rammer, T. A.; Ashbourn, S. F. M.

    2004-01-01

    Halogen species are known to catalytically destroy ozone in several regions of the atmosphere. In addition to direct catalytic losses, bromine compounds can indirectly enhance ozone loss through coupling to other radical families. Hypobromous acid (HOBr) is a key species in the linkage of BrOx to ClOx and HOx. The aqueous- phase coupling reaction HOBr + HCI (right arrow) BrCl + H2O may provide a pathway for chlorine activation on sulfate aerosols at temperatures warmer than those required for polar stratospheric cloud formation. We have measured t h e solubility of HOBr in 45 - 70 wt% sulfuric acid solutions. Over the temperature range 201 - 252 K, HOBr is quite soluble in sulfuric acid, H* = 10(exp 4) - 10(exp 7) mol dm(exp -3) atm(exp -1). The expected inverse dependence of H* on temperature was observed, but only a weak dependence on acidity was found. The solubility of HOBr is comparable to that of HBr, indicating that equilibrium concentrations of HOBr could equal or exceed those of HBr in upper tropospheric and lower stratospheric aerosols. Despite the high solubility of HOBr, aerosol volumes are not large enough to sequester a significant fraction of inorganic bromine from the gas phase. Our measurements of HOBr uptake in aqueous sulfuric acid in the presence of other brominated gases show the evolution of gaseous products including Br2O and Br2.

  2. Simultaneous determination of nitric acid and uranium concentrations in aqueous solution from measurements of electrical conductivity, density, and temperature

    SciTech Connect

    Spencer, B.B.

    1991-01-01

    Nuclear fuel reprocessing plants handle aqueous solutions of nitric acid and uranium in large quantities. Automatic control of process operations requires reliable measurements of these solutes concentration, but this is difficult to directly measure. Physical properties such as solution density and electrical conductivity vary with solute concentration and temperature. Conductivity, density and temperature can be measured accurately with relatively simple and inexpensive devices. These properties can be used to determine solute concentrations will good correlations. This paper provides the appropriate correlations for solutions containing 2 to 6 Molar (M) nitric acid and 0 to 300 g/L uranium metal at temperatures from 25--90{degrees}C. The equations are most accurate below 5 M nitric acid, due to a broad maximum in the conductivity curve at 6 M. 12 refs., 9 figs., 6 tabs.

  3. Acid deposition in Maryland: Summary of results through 1989. Final report

    SciTech Connect

    DeMuro, J.; Bowman, M.; Maxwell, C.; Asante-Duah, D.; Meyers, S.

    1990-06-01

    The Chesapeake Bay Research and Monitoring Program coordinates Maryland's acid deposition research and reports research results annually. The report evaluates several major topic areas including transport and chemistry of acid deposition, its potential impacts on the State's streams and fish, possible impacts on terrestrial resources such as crops and forests and on materials, the ability of energy conservation programs to reduce emissions of acid-forming pollutants, and mitigation techniques for neutralizing acid waters.

  4. Acid deposition in Maryland: summary of results through 1988. Annual report

    SciTech Connect

    Not Available

    1989-01-01

    The Chesapeake Bay Research and Monitoring Program coordinates Maryland's acid-deposition research and reports research results annually. This report evaluates several major topic areas including transport and chemistry of acid deposition its potential impacts on the State's streams and fish, possible impacts on terrestrial resources such as crops and forests and on materials, the ability of energy conservation programs to reduce emissions of acid-forming pollutants, and mitigation techniques for neutralizing acid waters.

  5. Efficiency of hexane extraction of napropamide from Aldrich humic acid and soil solutions

    SciTech Connect

    Williams, C.F.; Letey, J.; Farmer, W.J.; Nelson, S.D.; Anderson, M.; Ben-Hur, M.

    1999-12-01

    Dissolved organic matter (DOM) has been shown to form a stable complex with napropamide [2({alpha}-naphthoxy)-N,N-diethyl propionamide] and to facilitate its transport through soil columns. Liquid-liquid extraction of organics is a common method to transfer napropamide from water into an organic phase for gas chromatography analysis. A study was conducted to determine the effect of Aldrich humic acid, soil-derived dissolved organic matter, electrical conductivity, and hydrogen ion activity on the ability of hexane to extract napropamide from solutions and from soil extracts. The electrical conductivity from solutions and from soil extracts. The electrical conductivity of Aldrich humic acid solutions were adjusted to 0.01, 0.97, and 1.69 dS m{sup {minus}1} by adding NaCl and CaCl{sub 2}, and pH was adjusted using HCl and NaOH. Electrical conductivity had no effect on extraction efficiency. In the absence of DOM pH had no effect on extraction efficiency. In the absence of DOM pH had no effect on extraction efficiency. Extraction efficiency decreased with increasing DOM concentration. Maximum reduction in extraction efficiency occurred in the presence of DOM when solution pH was near neutrality. A maximum extraction efficiency of 100% was observed in the absence of DOM and a minimum of 68% when napropamide was added to DOM solutions at pH 8.2 and then lowered to pH 5.6. Management practices such as liming and allowing napropamide to dry on the soil may increase environmental transport. Also quantification of napropamide in environmental samples can be affected by DOM.

  6. Plasma amino acid concentrations in normal adults administered aspartame in capsules or solution: lack of bioequivalence.

    PubMed

    Stegink, L D; Filer, L J; Bell, E F; Ziegler, E E

    1987-05-01

    Some clinical studies require administration of test compounds in capsules to assure that the compound cannot be distinguished from a placebo. This raises the question of whether the pharmacokinetic responses produced by capsule administration are similar to values obtained when test compounds are ingested in solution. To test this, plasma phenylalanine and aspartate concentrations were compared in ten normal subjects ingesting 3 g aspartame in solution and in capsules in a balanced Latin square design. Peak plasma phenylalanine levels were significantly higher (191 +/- 65.4 v 117 +/- 39.5 mumol/L, mean +/- SD) and were reached significantly earlier (32 +/- 15 v 123 +/- 74 minutes) when aspartame was administered in solution than when it was administered in capsules. The area under the four-hour plasma phenylalanine concentration-time curve was significantly higher (15,340 +/- 4,820 v 8,465 +/- 3,356 mumol/L X min) when aspartame was ingested in solution. Administration in solution also produced a significantly higher ratio of plasma phenylalanine concentration to the sum of the plasma concentrations of the other large neutral amino acids (0.36 +/- 0.12 v 0.23 +/- 0.06). Similarly, peak plasma aspartate concentrations were significantly higher 26.2 +/- 16.3 v 10.4 +/- 5.0 mumol/L) and were reached significantly earlier (30 +/- 14 v 106 +/- 61.3 min) when aspartame was administered in solution. The data indicate different plasma phenylalanine and aspartate pharmacokinetics between solution and capsule administration of aspartame.

  7. Effect of hypochlorous acid solution on the eradication and prevention of Pseudomonas aeruginosa infection, serum biochemical variables, and cecum microbiota in rats.

    PubMed

    Goto, Kazuo; Kuwayama, Eri; Nozu, Ryoko; Ueno, Masami; Hayashimoto, Nobuhito

    2015-01-01

    In this study, hypochlorous acid solution, a weak acid, provided as drinking water to rats, was evaluated for its ability to eradicate and prevent Pseudomonas aeruginosa infection, while monitoring its simultaneous effect on serum biochemical variables and microbiota in the rat cecum. The results suggest that the solution could not eliminate the bacteria in the experimentally infected rats; however, the administration of a 10-parts-per-million (ppm) hypochlorous acid solution as drinking water was effective in inhibiting horizontal spread of P. aeruginosa infection among cage mates. Additionally, exposure to hypochlorous solution did not have any effect on serum biochemical variables of the rat including levels of total cholesterol, aspartate aminotransferase (AST), alanine aminotransferase (ALT), alkaline phosphatase (ALP), albumin, total bilirubin, lipase, amylase, urea nitrogen, total protein, calcium (Ca), phosphorus (P), sodium (Na), chlorine (Cl), except for potassium (K) levels. The most frequently isolated bacteria in the rat cecum included species belonging to Bacteroidales, Lactobacillus, Clostridiales, Erysipelotrichaceae, Akkermansia, Coriobacteriales, and Firmicutes. The ratio of the terminal restriction fragment length polymorphism (T-RFLP) peaks did not differ across rats administered with 5 and 10 ppm weak acid solution as compared to the control group for any of the bacteria, except for Erysipelotrichaceae and Firmicutes, where the ratio of T-RFLP peaks was higher in the 5 ppm group for Erysipelotrichaceae and in the 10 ppm group for Firmicutes than that in the control group (P<0.01). The results suggest that the weak acid hypochlorous solution could not eradicate P. aeruginosa completely from rats. The solution was effective in preventing infection without affecting serum biochemical variables; however, some of bacterial microbiota may have changed due to administration of the solution.

  8. Effect of hypochlorous acid solution on the eradication and prevention of Pseudomonas aeruginosa infection, serum biochemical variables, and cecum microbiota in rats

    PubMed Central

    GOTO, Kazuo; KUWAYAMA, Eri; NOZU, Ryoko; UENO, Masami; HAYASHIMOTO, Nobuhito

    2015-01-01

    In this study, hypochlorous acid solution, a weak acid, provided as drinking water to rats, was evaluated for its ability to eradicate and prevent Pseudomonas aeruginosa infection, while monitoring its simultaneous effect on serum biochemical variables and microbiota in the rat cecum. The results suggest that the solution could not eliminate the bacteria in the experimentally infected rats; however, the administration of a 10-parts-per-million (ppm) hypochlorous acid solution as drinking water was effective in inhibiting horizontal spread of P. aeruginosa infection among cage mates. Additionally, exposure to hypochlorous solution did not have any effect on serum biochemical variables of the rat including levels of total cholesterol, aspartate aminotransferase (AST), alanine aminotransferase (ALT), alkaline phosphatase (ALP), albumin, total bilirubin, lipase, amylase, urea nitrogen, total protein, calcium (Ca), phosphorus (P), sodium (Na), chlorine (Cl), except for potassium (K) levels. The most frequently isolated bacteria in the rat cecum included species belonging to Bacteroidales, Lactobacillus, Clostridiales, Erysipelotrichaceae, Akkermansia, Coriobacteriales, and Firmicutes. The ratio of the terminal restriction fragment length polymorphism (T-RFLP) peaks did not differ across rats administered with 5 and 10 ppm weak acid solution as compared to the control group for any of the bacteria, except for Erysipelotrichaceae and Firmicutes, where the ratio of T-RFLP peaks was higher in the 5 ppm group for Erysipelotrichaceae and in the 10 ppm group for Firmicutes than that in the control group (P<0.01). The results suggest that the weak acid hypochlorous solution could not eradicate P. aeruginosa completely from rats. The solution was effective in preventing infection without affecting serum biochemical variables; however, some of bacterial microbiota may have changed due to administration of the solution. PMID:25736708

  9. Solution structure of the squash aspartic acid proteinase inhibitor (SQAPI) and mutational analysis of pepsin inhibition.

    PubMed

    Headey, Stephen J; Macaskill, Ursula K; Wright, Michele A; Claridge, Jolyon K; Edwards, Patrick J B; Farley, Peter C; Christeller, John T; Laing, William A; Pascal, Steven M

    2010-08-27

    The squash aspartic acid proteinase inhibitor (SQAPI), a proteinaceous proteinase inhibitor from squash, is an effective inhibitor of a range of aspartic proteinases. Proteinaceous aspartic proteinase inhibitors are rare in nature. The only other example in plants probably evolved from a precursor serine proteinase inhibitor. Earlier work based on sequence homology modeling suggested SQAPI evolved from an ancestral cystatin. In this work, we determined the solution structure of SQAPI using NMR and show that SQAPI shares the same fold as a plant cystatin. The structure is characterized by a four-strand anti-parallel beta-sheet gripping an alpha-helix in an analogous manner to fingers of a hand gripping a tennis racquet. Truncation and site-specific mutagenesis revealed that the unstructured N terminus and the loop connecting beta-strands 1 and 2 are important for pepsin inhibition, but the loop connecting strands 3 and 4 is not. Using ambiguous restraints based on the mutagenesis results, SQAPI was then docked computationally to pepsin. The resulting model places the N-terminal strand of SQAPI in the S' side of the substrate binding cleft, whereas the first SQAPI loop binds on the S side of the cleft. The backbone of SQAPI does not interact with the pepsin catalytic Asp(32)-Asp(215) diad, thus avoiding cleavage. The data show that SQAPI does share homologous structural elements with cystatin and appears to retain a similar protease inhibitory mechanism despite its different target. This strongly supports our hypothesis that SQAPI evolved from an ancestral cystatin.

  10. Plasma membrane sterols are involved in yeast's ability to adsorb polyphenolic compounds resulting from wine model solution browning.

    PubMed

    Márquez, Trinidad; Millán, Carmen; Salmon, Jean-Michel

    2009-09-01

    The aim of this work was to demonstrate the direct interaction between membrane sterols of yeast lees and some polymerized phenolic compounds resulting from wine model solution browning. For this purpose, we first demonstrated by measurement of steady-state fluorescence anisotropy of the cationic fluorescent TMA-DPH probe the effect of polymerized compounds from the model reactions of (+)-catechin/acetaldehyde and (+)-catechin/glyoxylic acid on the plasma membrane order of Saccharomyces cerevisiae yeast lees enriched with different sterols. In a second set of experiments, we used S. cerevisiae plasma membrane vesicles spiked with different sources of sterol (ergosterol, cholesterol or a mix of grape phytosterols) to assess the effect of the same polymerized compounds on both vesicle integrity and membrane leakiness to protons by ACMA fluorescence. All the obtained results prove that yeast membrane sterols are able to strongly interact with some polymerized compounds resulting from the browning of model solutions, likely explaining the yeast ability to adsorb polyphenolic compounds and mainly the colorless intermediate compounds of the browning reactions. PMID:19691282

  11. Comprehensive study of the chemical reactions resulting from the decomposition of chloroform in alkaline aqueous solution

    NASA Astrophysics Data System (ADS)

    Estevez Mews, Jorge

    Chloroform (CHCl3) is a volatile liquid, which has a rather slow rate of decomposition in ground water. It is a known carcinogen and one of the most common contaminants found at toxic waste sites. The dominant degradation process for chloroform in both the atmosphere and the groundwater is the reaction with the hydroxyl radical or hydroxide ion. This process triggers a sequence of reactions which ultimately yield carbon monoxide, hydrogen chloride, and formic acid. The rate of chloroform degradation is considerably larger in solution than that in the gas phase and it increases dramatically with increasing pH. However, only one of the viable reactions had been studied previously at a high level of theory in solution. It is of great interest to gain a deeper understanding of the decomposition reaction mechanism. Quantum mechanical methods are well suited for studying the mechanism of organic reactions. However, a full quantum mechanical treatment of the entire fluid system is not computationally feasible. In this work, combined quantum mechanical and molecular mechanical (QM/MM) methods are used for studying chemical reactions in condensed phases. In these calculations, the solute molecules are treated quantum mechanically (QM), whereas the solvent molecules are approximated by empirical (MM) potential energy functions. The use of quantum mechanics and statistical sampling simulation is necessary to determine the reaction free energy profile. In the present study, the ab initio Hartree-Fock theory along with the 3-21G basis set was used in the quantum mechanical calculations to elucidate the reaction pathways of chloroform decomposition, with a focus on basic reaction conditions. Statistical mechanical Monte Carlo approach was then applied in molecular mechanical simulations, employing the empirical TIP3P model for water. We employed state-of-the-art electronic structure methods to determine the gas-phase inter-nuclear potential energy profile for all the relevant

  12. Influence of Acidity on Uranyl Nitrate Association in Aqueous Solutions: A Molecular Dynamics Simulation Study

    SciTech Connect

    de Almeida, Valmor F; Cui, Shengting; Khomami, Bamin; Ye, Xianggui; Smith, Rodney Bryan

    2010-01-01

    Uranyl ion complexation with water and nitrate is a key aspect of the uranium/plutonium extraction process. We have carried out a molecular dynamics simulation study to investigate this complexation process, including the molecular composition of the various complex species, the corresponding structure, and the equilibrium distribution of the complexes. The observed structures of the complexes suggest that in aqueous solution, uranyls are generally hydrated by 5 water molecules in the equatorial plane. When associating with nitrate ions, a water molecule is replaced by a nitrate ion, preserving the five-fold coordination and planar symmetry. Analysis of the pair correlation function between uranyl and nitrate suggests that nitrates bind to uranyl in aqueous solution mainly in a monodentate mode, although a small portion of bidentates occur. Dynamic association and dissociation between uranyls and nitrates take place in aqueous solution with a substantial amount of fluctuation in the number of various uranyl nitrate species. The average number of the uranyl mononitrate complexes shows a dependence on acid concentration consistent with equilibrium-constant analysis, namely, the concentration of [UO2NO3]+ increases with nitric acid concentration.

  13. Removal of acidic indigo carmine textile dye from aqueous solutions using radiation induced cationic hydrogels.

    PubMed

    Sari, Müfrettin Murat

    2010-01-01

    This study examined the removal of acidic indigo carmine dyes from aqueous solutions using cationic hydrogels. Irradiated hydrogels were investigated as a new sorbent for dye removal from aqueous solution. Poly(N,N-Diethylamino ethyl methacrylate) [poly(DEAEMA)] hydrogels were prepared by radiation polymerisation of N,N-diethylamino ethyl methacrylate [DEAEMA] monomer in the presence of cross-linking agent, ethylene glycol dimethacrylate [EGDMA], and used for the removal of acidic indigo carmine textile dye. The adsorption of dyes was examined using a batch sorption technique. The effects of pH, time and initial dye concentration on the adsorption capacity of hydrogels were investigated. Maximum gelation ratio was 98.2% at irradiation dose of 5.3 kGy. Maximum equilibrium volume swelling, V/V(0), value was 21.3 at pH 2.8. Maximum amount of adsorbed indigo carmine onto hydrogels was 96.7 mg dye/g gel at pH 2.8, 21 h of adsorption time and 120 mg/L initial dye solution. Swelling and adsorption capacity increased with decreasing of pH. Compared with Congo red, amounts of adsorbed indigo carmine are much higher than those of Congo red. Langmuir isotherm model was the best fit for these poly(DEAEMA) hydrogels-indigo carmine systems.

  14. Effect of initial solution pH on photo-induced reductive decomposition of perfluorooctanoic acid.

    PubMed

    Qu, Yan; Zhang, Chao-Jie; Chen, Pei; Zhou, Qi; Zhang, Wei-Xian

    2014-07-01

    The effects of initial solution pH on the decomposition of perfluorooctanoic acid (PFOA) with hydrated electrons as reductant were investigated. The reductive decomposition of PFOA depends strongly on the solution pH. In the pH range of 5.0-10.0, the decomposition and defluorination rates of PFOA increased with the increase of the initial solution pH. The rate constant was 0.0295 min(-1) at pH 10.0, which was more than 49.0 times higher than that at pH 5.0. Higher pH also inhibits the generation of toxic intermediates during the PFOA decomposition. For example, the short-chain PFCAs reached a lower maximum concentration in shorter reaction time as pH increasing. The peak areas of accumulated fluorinated and iodinated hydrocarbons detected by GC/MS under acidic conditions were nearly 10-100 times more than those under alkaline conditions. In short, alkaline conditions were more favorable for photo-induced reduction of PFOA as high pH promoted the decomposition of PFOA and inhibited the accumulation of intermediate products. The concentration of hydrated electron, detected by laser flash photolysis, increased with the increase of the initial pH. This was the main reason why the decomposition of PFOA in the UV-KI system depended strongly on the initial pH.

  15. Electrolytic recovery of copper and regeneration of nitric acid from a copper strip solution

    SciTech Connect

    Stewart, T.L.; Hartley, J.N.

    1985-01-01

    The fabrication of nuclear fuels involves stripping of a copper jacket with nitric acid. The waste acid, which contains 3.0 to 4.5 N nitric acid and 100 to 180 g/L copper, is currently discharged, neutralized, and disposed of in solar evaporation ponds. Alternative waste disposal and treatment methods including electrowinning are being investigated. Laboratory-scale electrowinning tests have been conducted in an air-sparged cell at current densities from 0.027 to 0.22 A/cm/sup 2/. The efficiency of copper recovery was improved by adding sulfamic acid or by cooling the electrolyte. Copper current efficiency ranged from 55% to 95%; energy consumption ranged from 1.8 to 6.6 kWh/kg Cu. Results of the laboratory-scale electrowinning tests are summarized. A brief economic comparison of an alternative waste disposal and acid recycle technique is presented.

  16. Improving impurities clearance by amino acids addition to buffer solutions for chromatographic purifications of monoclonal antibodies.

    PubMed

    Ishihara, Takashi; Hosono, Mareto

    2015-07-15

    The performance of amino acids in Protein A affinity chromatography, anion exchange chromatography and cation exchange chromatography for monoclonal antibody purification was investigated. Glycine, threonine, arginine, glutamate, and histidine were used as buffer components in the equilibration, washing, and elution steps of these chromatographies. Improved clearance of impurity, high molecular weight species (HMW) and host cell proteins (HCP) was observed in the purification processes when using the amino acids as base-buffer constituents, additives or eluents compared with that of buffers without these amino acids. In addition, we designed a buffer system in which the mobile phases were composed of only a single amino acid, histidine, and applied it to the above three chromatographies. Effective HMW and HCP clearance was also obtained in this manner. These results suggest that amino acids may enhance impurity clearance during the purification of monoclonal antibodies. PMID:26057847

  17. Enhanced copper surface protection in aqueous solutions containing short-chain alkanoic acid potassium salts.

    PubMed

    Abelev, Esta; Starosvetsky, David; Ein-Eli, Yair

    2007-10-23

    The ability of dissolved potassium monocarboxylate salts to produce surface passivation and to inhibit aqueous corrosion of copper was studied. The electrochemical measurements indicate that the inhibiting efficiency of these compounds, with a general formula Cn-1H2n-1COOK or CnK (n=3...12), is dependent on the hydrocarbon chain length. The inhibiting efficiency was higher for a longer hydrocarbon chain of n-alkanoic acid. The degree of copper protection was found to increase with an increase in n-alkanoic acid potassium salt concentration; the optimum concentration of potassium dodecanoate (C12K) in sulfate solutions was found to be 0.07 M. The protective layers formed at the copper surface subsequent to exposure in various n-alkanoic acid potassium salt solutions were characterized by contact angle measurements, electrochemical impedance spectroscopy, X-ray photoelectron spectroscopy, and Fourier transform infrared reflection spectroscopy. Pronounced copper protection was attributed to the growth of a protective film on the copper surface, containing both copper oxides and copper carboxylate compounds. It is suggested that the organic molecules enhance copper protection by covering copper oxides with a thin and dense organic layer, which prevents water molecules or aggressive anions from interacting with the copper surface.

  18. Investigation of the applicability of dielectric relaxation properties of amino acid solutions within the resonant recognition model.

    PubMed

    Pirogova, Elena; Simon, George P; Cosic, Irena

    2003-06-01

    The resonant recognition model (RRM) is a physicomathematical approach used to analyze the interactions of a protein and its target, using digital signal processing methods. The RRM is based on the finding that there is a significant correlation between the spectra of numerical presentation of protein sequences and their biological activities. Initially, the electron-ion interaction potential was used to represent each amino acid in the protein sequences. In this paper, the dielectric constant (epsilon') and dielectric loss tangent (tan delta) parameters have been determined for their possible use in the RRM. These parameters are based on the values of capacitance and conductance obtained experimentally for 20 amino acid solutions using dielectric spectroscopy for the case of the real component of dielectric permittivity; the parameter used is the dielectric increment (deltaepsilon'), the difference between dielectric constant of the amino acid solution and that of the solvent alone. The results of multiple cross-spectral analyses have shown that parameters analyzed generate in the consensus spectrum one dominant peak corresponding to the common biological activity of proteins studied, allowing the conclusion that these new parameters are suitable for use in the RRM approach.

  19. Theoretical studies of atomic properties and chemical stabilities in acid solutions of element Uus (Z=117) and Astatine

    NASA Astrophysics Data System (ADS)

    Chang, Z. W.; Li, J. G.; Dong, C. Z.

    2012-11-01

    Multi-configuration Dirac-Fock (MCDF) method was employed to calculate the first five ionization potentials, electron affinities, resonance excitation energies, oscillator strengths and radii for the element Uus and its homologue At. Main valence correlation effects were taken into account. The Breit interaction and QED effects were also estimated. The uncertainties of calculated IPs, EAs and IR for Uus and At were reduced through an extrapolation procedure. The good consistency with available experimental and other theoretical values demonstrates the validity of the present results. These theoretical data were further used to predict the chemical stabilities of element Uus and At in acid solutions.

  20. Effect of Ethephon, Indole Butyric Acid, and Treatment Solution pH on Rooting and on Ethylene Levels within Mung Bean Cuttings.

    PubMed

    Mudge, K W; Swanson, B T

    1978-02-01

    Light-grown mung bean (Phaseolus aureus Roxb.) cuttings were treated with buffered and nonbuffered solutions of Ethephon, indole butyric acid (IBA), and the combination of both. Ethephon treatment resulted in increased tissue ethylene levels with increasing solution pH, but had no effect on rooting. IBA treatment had no effect on tissue ethylene levels, but strongly promoted rooting. Combinations of Ethephon and IBA had no effect on rooting of mung bean cuttings beyond that obtained by IBA alone. PMID:16660274

  1. Diffusion of Small Solute Particles in Viscous Liquids: Cage Diffusion, a Result of Decoupling of Solute-Solvent Dynamics, Leads to Amplification of Solute Diffusion.

    PubMed

    Acharya, Sayantan; Nandi, Manoj K; Mandal, Arkajit; Sarkar, Sucharita; Bhattacharyya, Sarika Maitra

    2015-08-27

    We study the diffusion of small solute particles through solvent by keeping the solute-solvent interaction repulsive and varying the solvent properties. The study involves computer simulations, development of a new model to describe diffusion of small solutes in a solvent, and also mode coupling theory (MCT) calculations. In a viscous solvent, a small solute diffuses via coupling to the solvent hydrodynamic modes and also through the transient cages formed by the solvent. The model developed can estimate the independent contributions from these two different channels of diffusion. Although the solute diffusion in all the systems shows an amplification, the degree of it increases with solvent viscosity. The model correctly predicts that when the solvent viscosity is high, the solute primarily diffuses by exploiting the solvent cages. In such a scenario the MCT diffusion performed for a static solvent provides a correct estimation of the cage diffusion.

  2. Analysis of the corrosion of carbon steels in simulated salt repository brines and acid chloride solutions at high temperatures

    SciTech Connect

    Diercks, D.R.; Kassner, T.F.

    1988-04-01

    An analysis of literature data on the corrosion of carbon steels in anoxic brines and acid chloride solutions was performed, and the results were used to assess the expected life of high-level nuclear waste package containers in a salt repository environment. The corrosion rate of carbon steels in moderately acidic aqueous chloride environments obeys an Arrhenius dependence on temperature and a (pH{sub 2}){sup {minus}1/2} dependence on hydrogen partial pressure. The cathodic reduction of water to produce hydrogen is the rate-controlling step in the corrosion process. An expression for the corrosion rate incorporating these two dependencies was used to estimate the corrosion life of several proposed waste package configurations. 42 refs., 11 figs., 2 tabs.

  3. Comparable Efficacy of a 1-L PEG and Ascorbic Acid Solution Administered with Bisacodyl versus a 2-L PEG and Ascorbic Acid Solution for Colonoscopy Preparation: A Prospective, Randomized and Investigator-Blinded Trial

    PubMed Central

    Im, Jong Pil; Kim, Su Hwan; Koh, Seong-Joon; Kim, Byeong Gwan; Lee, Kook Lae; Kim, Sang Gyun; Kim, Joo Sung; Jung, Hyun Chae

    2016-01-01

    Background Two liters of polyethylene glycol (PEG) solution administered with ascorbic acid (Asc) can provide efficacy similar to that of a 4-L PEG solution for colonoscopy preparation. In addition, oral bisacodyl (Bis) has been shown to reduce the volume of PEG needed for a bowel preparation with comparable efficacy. This study aimed to compare the efficacy, tolerability and safety of a 2-L PEG solution mixed with Asc versus the combination of Bis, Asc and a 1-L PEG solution. Methods This was a prospective, randomized, multi-centre, single-blind, non-inferiority trial. Participants who were scheduled for colonoscopy were included and randomized to receive either 2-L PEG and Asc (2L PEG/Asc group) or 1-L PEG, Asc and 20 mg Bis (1L PEG/Asc + Bis group). The quality of bowel preparation was assessed using the Boston Bowel Preparation Scale. Data regarding tolerance, compliance and adverse events were also gathered. Results A total of 187 participants were analyzed; 96 were allocated to the 2L PEG/Asc group and 91 to the 1L PEG/Asc + Bis group. Bowel preparation was adequate in 87.5% (84/96) of patients in the 2L PEG/Asc group and 94.5% of the 1L PEG/Asc + Bis group (86/91, p = 0.10). There was no significant difference between the two groups with respect to compliance, tolerability or safety. The patients allocated to the 1L PEG/Asc + Bis group expressed more willingness to repeat the procedure than patients in the 2L PEG/Asc group (p = 0.01). Conclusions Bowel preparation with Bis and a 1-L PEG/Asc solution is as effective, well-tolerated, and safe as a 2-L PEG/Asc solution. Trial Registration ClinicalTrials.gov NCT 01745835; Clinical Research Information Service (CRiS) KCT0000708 PMID:27588943

  4. NEXAFS Chemical State and Bond Lengths of p-Aminobenzoic Acid in Solution and Solid State

    NASA Astrophysics Data System (ADS)

    Stevens, J. S.; Gainar, A.; Suljoti, E.; Xiao, J.; Golnak, R.; Aziz, E. F.; Schroeder, S. L. M.

    2016-05-01

    Solid-state and solution pH-dependent NEXAFS studies allow direct observation of the electronic state of para-aminobenzoic acid (PABA) as a function of its chemical environment, revealing the chemical state and bonding of the chemical species. Variations in the ionization potential (IP) and 1s→π* resonances unequivocally identify the chemical species (neutral, cationic, or anionic) present and the varying local environment. Shifts in σ* shape resonances relative to the IP in the NEXAFS spectra vary with C-N bond length, and the important effect of minor alterations in bond length is confirmed with nitrogen FEFF calculations, leading to the possibility of bond length determination in solution.

  5. Electrodeposited Films from Aqueous Tungstic Acid-Hydrogen Peroxide Solutions for Electrochromic Display Devices

    NASA Astrophysics Data System (ADS)

    Yamanaka, Kazusuke

    1987-11-01

    Electrodeposited tungsten oxide films from aqueous tungstic acid-hydrogen peroxide solutions were investigated for applications to electrochromic devices. These films exhibited electrochromism in aprotic electrolyte solutions containing Li-salts. When the films were heat-treated for an hour at temperatures between 100 and 200°C, the electrochromic reactions were rich in reversibility. The coloring efficiency and response rate for the films were favorable and comparable to those for tungsten trioxide evaporated films. A cell life-test was performed on several clock-size cells by applying a 1.2-V, 1-Hz, continuous square wave. The typical amount of charge required for coloration was about 50 C / m2 and remained unchanged even after 107 coloration-bleaching cycles.

  6. Nonclinical safety evaluation of boric acid and a novel borate-buffered contact lens multi-purpose solution, Biotrue™ multi-purpose solution.

    PubMed

    Lehmann, David M; Cavet, Megan E; Richardson, Mary E

    2010-12-01

    Multipurpose solutions (MPS) often contain low concentrations of boric acid as a buffering agent. Limited published literature has suggested that boric acid and borate-buffered MPS may alter the corneal epithelium; an effect attributed to cytotoxicity induced by boric acid. However, this claim has not been substantiated. We investigated the effect of treating cells with relevant concentrations of boric acid using two cytotoxicity assays, and also assessed the impact of boric acid on corneal epithelial barrier function by measuring TEER and immunostaining for tight junction protein ZO-1 in human corneal epithelial cells. Boric acid was also assessed in an in vivo ocular model when administered for 28 days. Additionally, we evaluated Biotrue multi-purpose solution, a novel borate-buffered MPS, alone and with contact lenses for ocular compatibility in vitro and in vivo. Boric acid passed both cytotoxicity assays and did not alter ZO-1 distribution or corneal TEER. Furthermore, boric acid was well-tolerated on-eye following repeated administration in a rabbit model. Finally, Biotrue multi-purpose solution demonstrated good ocular biocompatibility both in vitro and in vivo. This MPS was not cytotoxic and was compatible with the eye when administered alone and when evaluated with contact lenses. We demonstrate that boric acid and a borate-buffered MPS is compatible with the ocular environment. Our findings provide evidence that ocular effects reported for some borate-buffered MPS may be incorrectly attributed to boric acid and are more likely a function of the unique combination of ingredients in the MPS formulation tested.

  7. Inhibition of mild steel corrosion by sodium dodecyl benzene sulfonate and sodium oleate in acidic solutions

    SciTech Connect

    Luo, H.; Han, K.N.; Guan, Y.C.

    1998-08-01

    Inhibition of mild steel corrosion by sodium dodecyl benzene sulfonate (C{sub 12}H{sub 25}C{sub 6}H{sub 4}SO{sub 3}Na [SDBS]) and sodium oleate (CH{sub 3}[CH{sub 2}]{sub 7}CH{double_bond}CH[CH{sub 2}]{sub 7}COONa) in acidic solutions was investigated using a potentiostat, a lock-in amplifier, a contact angle goniometer, A fourier transform infrared (FTIR) spectrometer, and an ultraviolet (UV)/visible spectrophotometer. In the presence of the organic inhibitors, the corrosion rate was reduced significantly, Anionic SDBS was adsorbed on the positively charged mild steel surface through the electrostatic attraction. However, for sodium oleate, the soluble oleic acid (CH{sub 3}[CH{sub 2}]{sub 7}CH{double_bond}CH[CH]{sub 7}COOH) chemisorbed on the steel surface at the first stage. Then, insoluble colloid adsorbed on the chemisorbed surface through van der Waals forces.

  8. Solubility and reactivity of peroxyacetyl nitrate (PAN) in dilute aqueous salt solutions and in sulphuric acid

    NASA Astrophysics Data System (ADS)

    Frenzel, A.; Kutsuna, S.; Takeuchi, K.; Ibusuki, T.

    The loss rates of PAN in several dilute aqueous salt solutions (NaBr, Na 2SO 3, KI, NaNO 2, FeCl 3, and FeSO 4) and in sulphuric acid were measured at 279 K with a simple bubbler experiment. They are little different from that in pure water. For 5 M sulphuric acid hydrolysis and solubility were determined in the temperature range of 243-293 K. The hydrolysis rate kh=3.2×10 -4 s -1 at 293 K is close to that in water. The observed temperature dependence of the Henry's Law constant H=10- 6.6±0.6exp((4780±420)/T) M atm -1 leads to enthalpy and entropy of solvation Δ Hsolv=-39.7±3.5 kJ mol -1 and Δ Ssolv=-126±11 J mol -1 K -1, respectively.

  9. Photochemistry of nucleic acid bases and their thio- and aza-analogues in solution.

    PubMed

    Pollum, Marvin; Martínez-Fernández, Lara; Crespo-Hernández, Carlos E

    2015-01-01

    The steady-state and time-resolved photochemistry of the natural nucleic acid bases and their sulfur- and nitrogen-substituted analogues in solution is reviewed. Emphasis is given to the experimental studies performed over the last 3-5 years that showcase topical areas of scientific inquiry and those that require further scrutiny. Significant progress has been made toward mapping the radiative and nonradiative decay pathways of nucleic acid bases. There is a consensus that ultrafast internal conversion to the ground state is the primary relaxation pathway in the nucleic acid bases, whereas the mechanism of this relaxation and the level of participation of the (1)πσ*, (1) nπ*, and (3)ππ* states are still matters of debate. Although impressive research has been performed in recent years, the microscopic mechanism(s) by which the nucleic acid bases dissipate excess vibrational energy to their environment, and the role of the N-glycosidic group in this and in other nonradiative decay pathways, are still poorly understood. The simple replacement of a single atom in a nucleobase with a sulfur or nitrogen atom severely restricts access to the conical intersections responsible for the intrinsic internal conversion pathways to the ground state in the nucleic acid bases. It also enhances access to ultrafast and efficient inter-system crossing pathways that populate the triplet manifold in yields close to unity. Determining the coupled nuclear and electronic pathways responsible for the significantly different photochemistry in these nucleic acid base analogues serves as a convenient platform to examine the current state of knowledge regarding the photodynamic properties of the DNA and RNA bases from both experimental and computational perspectives. Further investigations should also aid in forecasting the prospective use of sulfur- and nitrogen-substituted base analogues in photochemotherapeutic applications. PMID:25238718

  10. Extensional flow of hyaluronic acid solutions in an optimized microfluidic cross-slot devicea

    PubMed Central

    Haward, S. J.; Jaishankar, A.; Oliveira, M. S. N.; Alves, M. A.; McKinley, G. H.

    2013-01-01

    We utilize a recently developed microfluidic device, the Optimized Shape Cross-slot Extensional Rheometer (OSCER), to study the elongational flow behavior and rheological properties of hyaluronic acid (HA) solutions representative of the synovial fluid (SF) found in the knee joint. The OSCER geometry is a stagnation point device that imposes a planar extensional flow with a homogenous extension rate over a significant length of the inlet and outlet channel axes. Due to the compressive nature of the flow generated along the inlet channels, and the planar elongational flow along the outlet channels, the flow field in the OSCER device can also be considered as representative of the flow field that arises between compressing articular cartilage layers of the knee joints during running or jumping movements. Full-field birefringence microscopy measurements demonstrate a high degree of localized macromolecular orientation along streamlines passing close to the stagnation point of the OSCER device, while micro-particle image velocimetry is used to quantify the flow kinematics. The stress-optical rule is used to assess the local extensional viscosity in the elongating fluid elements as a function of the measured deformation rate. The large limiting values of the dimensionless Trouton ratio, Tr ∼ O(50), demonstrate that these fluids are highly extensional-thickening, providing a clear mechanism for the load-dampening properties of SF. The results also indicate the potential for utilizing the OSCER in screening of physiological SF samples, which will lead to improved understanding of, and therapies for, disease progression in arthritis sufferers. PMID:24738010

  11. Effect of weak acid hypochlorous solution on selected viruses and bacteria of laboratory rodents.

    PubMed

    Taharaguchi, Motoko; Takimoto, Kazuhiro; Zamoto-Niikura, Aya; Yamada, Yasuko K

    2014-01-01

    Weak acid hypochlorous solution (WAHS) is known to have efficacy for inactivating pathogens and to be relatively safe with respect to the live body. Based on these advantages, many animal facilities have recently been introducing WAHS for daily cleaning of animal houses. In this study, we determined the effect of WAHS in inactivating specific pathogens of laboratory rodents and pathogens of opportunistic infection. WAHS with an actual chloride concentration of 60 ppm and a pH value of 6.0 was generated using purpose-built equipment. One volume of mouse hepatitis virus (MHV), Sendai virus, lymphocytic choriomeningitis virus, Bordetella bronchiseptica, Pasteurella pneumotropica, Corynebacterium kutscheri, Staphylococcus aureus, and Pseudomonas aeruginosa was mixed with 9 or 99 volumes of WAHS (×10 and ×100 reaction) for various periods (0.5, 1, and 5 min) at 25°C. After incubation, the remaining infectious viruses and live bacteria were determined by plaque assay or culture. In the ×100 reaction mixture, infectious viruses and live bacteria could not be detected for any of the pathogens examined even with the 0.5-min incubation. However, the effects for MHV, B. bronchiseptica, and P. aeruginosa were variable in the ×10 reaction mixture with the 0.5- and 1-min incubations. Sufficient effects were obtained by elongation of the reaction time to 5 min. In the case of MHV, reducing organic substances in the virus stock resulted in the WAHS being completely effective. WAHS is recommended for daily cleaning in animal facilities but should be used properly in order to obtain a sufficient effect, which includes such things as using a large enough volume to reduce effects of organic substances. PMID:24770639

  12. Extensional flow of hyaluronic acid solutions in an optimized microfluidic cross-slot device.

    PubMed

    Haward, S J; Jaishankar, A; Oliveira, M S N; Alves, M A; McKinley, G H

    2013-07-01

    We utilize a recently developed microfluidic device, the Optimized Shape Cross-slot Extensional Rheometer (OSCER), to study the elongational flow behavior and rheological properties of hyaluronic acid (HA) solutions representative of the synovial fluid (SF) found in the knee joint. The OSCER geometry is a stagnation point device that imposes a planar extensional flow with a homogenous extension rate over a significant length of the inlet and outlet channel axes. Due to the compressive nature of the flow generated along the inlet channels, and the planar elongational flow along the outlet channels, the flow field in the OSCER device can also be considered as representative of the flow field that arises between compressing articular cartilage layers of the knee joints during running or jumping movements. Full-field birefringence microscopy measurements demonstrate a high degree of localized macromolecular orientation along streamlines passing close to the stagnation point of the OSCER device, while micro-particle image velocimetry is used to quantify the flow kinematics. The stress-optical rule is used to assess the local extensional viscosity in the elongating fluid elements as a function of the measured deformation rate. The large limiting values of the dimensionless Trouton ratio, Tr ∼ O(50), demonstrate that these fluids are highly extensional-thickening, providing a clear mechanism for the load-dampening properties of SF. The results also indicate the potential for utilizing the OSCER in screening of physiological SF samples, which will lead to improved understanding of, and therapies for, disease progression in arthritis sufferers.

  13. Absorption of sulfur dioxide from simulated flue gas by polyethyleneimine-phosphoric acid solution.

    PubMed

    Bo, Wen; Li, Hongxia; Zhang, Junjie; Song, Xiangjia; Hu, Jinshan; Liu, Ce

    2016-12-01

    Clean fuel technologies have been widely developed in current society because fuel combustion can directly bring about the emission of hazardous gasses such as SO2. Flue gas desulfurization by polyethyleneimine (PEI)-phosphoric acid solution is an efficient desulfurization method. In this research, the PEI and the additive H3PO4 were used as absorption solution. SO2 was absorbed by the system and desorbed from the loaded solution. The cycle operation was also analyzed. Some technology conditions such as the concentration of PEI, the temperature, the gas flow rate, the concentration of SO2 and the pH value were experimentally researched. With the optimized process, the absorption efficiency of this system could reach 98% and the desorption efficiency was over 60%, showing good absorption/desorption capability. With this efficient approach, the present study may open a new window for developing high-performance absorbents which can make SO2 be well desorbed from the loaded solution and better reused in the flue gas desulfurization. PMID:27082307

  14. Spectroscopic studies of alumina-supported nickel catalysts precursors. Part I. Catalysts prepared from acidic solutions

    NASA Astrophysics Data System (ADS)

    Pasieczna-Patkowska, S.; Ryczkowski, J.

    2007-04-01

    Nickel alumina-supported catalysts were prepared from acidic solutions of nickel nitrate by the CIM and DIM methods (classical and double impregnation, respectively). The catalysts exhibited different nickel species due to the existence of various metal-support interaction strengths. As a consequence, the reducibility and other surface properties changed as a function of the preparation method. The aim of this work was to study the interaction between the metal precursor and the alumina surface by means of FT-IR (Fourier transform infrared) and FT-IR/PAS (FT-IR photoacoustic spectroscopy).

  15. Acridine-based complex as amino acid anion fluorescent sensor in aqueous solution

    NASA Astrophysics Data System (ADS)

    Dai, Yanpeng; Xu, Kuoxi; Li, Qian; Wang, Chaoyu; Liu, Xiaoyan; Wang, Peng

    2016-03-01

    Novel acridine-based fluorescence sensors containing alaninol ligands, L1 and D1, were designed and synthesized. The structure of the compound was characterized by IR, 1H NMR, 13C NMR, MS spectra. L1 and D1 possess efficient Cu2 + cation ON-OFF selective signaling behavior based on ligand-to-metal binding mechanism at physiological pH condition. Additionally, the L1-Cu(II) and D1-Cu(II) complexes could further serve as reversible OFF-ON signaling sensing ensemble to allow ratiometric response to amino acid anion in aqueous solution.

  16. Perfluorinated alcohols and acids induce coacervation in aqueous solutions of amphiphiles.

    PubMed

    Khaledi, Morteza G; Jenkins, Samuel I; Liang, Shuang

    2013-02-26

    We have discovered that water-miscible perfluorinated alcohols and acids (FA) can induce simple and complex coacervation in aqueous solutions of a wide range of amphiphilic molecules such as synthetic surfactants, phospholipids, and bile salts as well as polyelectrolytes. This unique phenomenon seems to be nearly ubiquitous, especially for complex coacervate systems composed of mixed catanionic amphiphiles. In addition, coacervation and aqueous phase separation were observed over a wide range of surfactants concentrations and for different mole fractions of the oppositely charged amphiphile.

  17. Potentiodynamic polarization effect on phase and microstructure of SAC305 solder in hydrochloric acid solution

    NASA Astrophysics Data System (ADS)

    Zaini, Nurwahida Binti Mohd; Nazeri, Muhammad Firdaus Bin Mohd

    2016-07-01

    The corrosion analysis of SAC305 lead free solder was investigated in Hydrochloric acid (HCl) solution. Potentiodynamic polarization was used to polarize the SAC305. The effect of polarization on the phase and microstructure were compared to as-prepared SAC305 solder. Potentiodynamic polarization introduces mixed corrosion products on the surface of SAC305 solder. The XRD analysis confirms that the mixed corrosion products emerged on the surface after polarization by formation of SnO and SnO2 of which confirmed that dissolution of Sn was dominant during polarization. Microstructure analysis reveal the presence of gap and porosities produced limits the protection offered by the passivation film.

  18. Two new frameworks of potassium saccharate obtained from acidic and alkaline solution

    SciTech Connect

    Lv, Yao-Kang; Feng, Yun-Long; Liu, Ji-Wei; Jiang, Zhan-Guo

    2011-05-15

    Two chiral K(I) complexes based on D-saccharic acid (H{sub 2}sac), [K(Hsac)]{sub n} (1) and [K{sub 2}(sac)]{sub n} (2) were obtained from acidic and alkaline solution. The 3D framework of 1 includes K(I) polyhedral rods and typical pairwise coaxial right- and left-handed helical chains, and displays binodal 6-connected pcu topology. 2 contains 2D polyhedral sheets consisting of left-handed helical chains, and generates 3D network with an unprecedented (7,11)-connected net. Cyclic voltammetry tests and charge-discharge tests indicate that the addition of complex 2 to the electrolyte could improve the electrochemical properties of the nickel hydroxide electrode. -- Graphical abstract: Two K(I) complexes based on D-saccharic acid (H{sub 2}sac), [K(Hsac)]{sub n} (1) and [K{sub 2}(sac)]{sub n} (2) were obtained and characterized. Electrochemical studies indicate the potential use of 2 in Ni-MH battery. Display Omitted highlights: > Two novel chiral K(I) frameworks based on D-saccharic acid were obtained. > The structure of 1 includes K(I) polyhedral rods and typical helical chains. > 2 contains 2D polyhedral sheets and generates an unprecedented (7,11)-connected net. > Addition of 2 to electrolyte could improve the nickel hydroxide electrode's property.

  19. Reactivity of alanylalanine diastereoisomers in neutral and acid aqueous solutions: a versatile stereoselectivity.

    PubMed

    Plasson, Raphaël; Tsuji, Maika; Kamata, Masazumi; Asakura, Kouichi

    2011-10-01

    A good comprehension of the reactivity of peptides in aqueous solution is fundamental in prebiotic chemistry, namely for understanding their stability and behavior in primitive oceans. Relying on the stereoselectivity of the involved reactions, there is a huge interest in amino acid derivatives for explaining the spontaneous emergence of homochirality on primitive Earth. The corresponding kinetic and thermodynamic parameters are however still poorly known in the literature. We studied the reactivity of alanylalanine in acidic to neutral conditions as a model system. The hydrolysis into amino acids, the epimerization of the N-terminal residue, and the cyclization into diketopiperazine could be successfully identified and studied. This kinetic investigation highlighted interesting behaviors. Complex mechanisms were observed in very acidic conditions. The relative kinetic stability of the diastereoisomers of the dipeptide is highly dependent of the pH, with the possibility to dynamically destabilize the thermodynamically more stable diastereoisomers. The existence of the cyclization of dipeptides adds complexity to the system. On one hand it brings additional stereoselectivities; on the other hand fast racemization of heterochiral dipeptides is obtained.

  20. Reactivity of Alanylalanine Diastereoisomers in Neutral and Acid Aqueous Solutions: a Versatile Stereoselectivity

    NASA Astrophysics Data System (ADS)

    Plasson, Raphaël; Tsuji, Maika; Kamata, Masazumi; Asakura, Kouichi

    2011-10-01

    A good comprehension of the reactivity of peptides in aqueous solution is fundamental in prebiotic chemistry, namely for understanding their stability and behavior in primitive oceans. Relying on the stereoselectivity of the involved reactions, there is a huge interest in amino acid derivatives for explaining the spontaneous emergence of homochirality on primitive Earth. The corresponding kinetic and thermodynamic parameters are however still poorly known in the literature. We studied the reactivity of alanylalanine in acidic to neutral conditions as a model system. The hydrolysis into amino acids, the epimerization of the N-terminal residue, and the cyclization into diketopiperazine could be successfully identified and studied. This kinetic investigation highlighted interesting behaviors. Complex mechanisms were observed in very acidic conditions. The relative kinetic stability of the diastereoisomers of the dipeptide is highly dependent of the pH, with the possibility to dynamically destabilize the thermodynamically more stable diastereoisomers. The existence of the cyclization of dipeptides adds complexity to the system. On one hand it brings additional stereoselectivities; on the other hand fast racemization of heterochiral dipeptides is obtained.

  1. Inhibitory effect of aroma on the bitterness of branched-chain amino acid solutions.

    PubMed

    Mukai, Junji; Tokuyama, Emi; Ishizaka, Toshihiko; Okada, Sachie; Uchida, Takahiro

    2007-11-01

    Nutritional products for patients with liver failure available on the Japanese market contain many branched-chain amino acids (BCAAs) such as L-leucine, L-isoleucine, and L-valine, which not only have a bitter taste but also strong, unpleasant odours, leading to low palatability. The palatability of these nutritional products can be significantly improved by the addition of flavoured powders containing various kinds of tastants (sucrose, citric acid, etc.) and odourants (fruit, coffee aromas, etc.). The specific effects of the aroma of flavoured powders have not yet been clearly evaluated. In the present article, the inhibitory effect of aroma on the bitterness of BCAA solutions was examined. The bitterness intensity of a BCAA solution at the same concentration as Aminoleban EN was defined as 3.5 (measured by a previously described gustatory sensation method). The bitterness threshold of a BCAA standard solution without added aroma was estimated to be 1.87, while those of BCAA solutions containing green-tea, coffee, apple, vanilla, or strawberry aromas were 2.02, 1.98, 2.35, 2.40 and 2.87, respectively, when evaluated by the probit method. This shows that the addition of an aroma can elevate the bitterness threshold in human volunteers. The green-tea and coffee aromas predominantly evoked bitterness, while the vanilla aroma predominantly evoked sweetness. Apple and strawberry aromas evoked both sweetness and sourness, with the apple aroma having stronger sourness and the strawberry aroma stronger sweetness. Thus, a 'sweet' aroma suppresses the bitterness of BCAA, with coexisting sourness also participating in the bitterness inhibition.

  2. Leaching of organic acids from irradiated EVA plastic as a function of solution pH and polarity.

    PubMed

    Jenke, Dennis; Zietlow, David; Sadain, Salma

    2004-01-01

    The leaching of several target organic acids from an irradiated ethylene vinyl acetate material, such as those used as a solution product container, is examined as a function of solution pH and polarity. The targeted compounds included highly soluble weak acids such as acetic and formic acids, and larger, more lipophillic acids such as myristic, palmitic, and stearic acids. The leaching of these compounds was examined over a pH range of 3 to 11 and in various ethanol/water proportions. While pH and solution polarity had only a modest impact on the accumulation of the acetic and formic acids, the accumulation of the fatty acids was greatly affected by both factors. It is suggested that the accumulation of these leachables at high pH is influenced by two processes. The first process, partitioning, the speciation of the acidic leachables (protonated versus dissociated form) contributes to the pH trends observed. In this case, entities that already exist in the plastic partition themselves between the plastic and solution via migration. A second, more important, contributor to the leaching of these acids is a pH-dependent increase in their availability arising from an unspecified reactive process.

  3. Effects of intravenous solutions on acid-base equilibrium: from crystalloids to colloids and blood components.

    PubMed

    Langer, Thomas; Ferrari, Michele; Zazzeron, Luca; Gattinoni, Luciano; Caironi, Pietro

    2014-01-01

    Intravenous fluid administration is a medical intervention performed worldwide on a daily basis. Nevertheless, only a few physicians are aware of the characteristics of intravenous fluids and their possible effects on plasma acid-base equilibrium. According to Stewart's theory, pH is independently regulated by three variables: partial pressure of carbon dioxide, strong ion difference (SID), and total amount of weak acids (ATOT). When fluids are infused, plasma SID and ATOT tend toward the SID and ATOT of the administered fluid. Depending on their composition, fluids can therefore lower, increase, or leave pH unchanged. As a general rule, crystalloids having a SID greater than plasma bicarbonate concentration (HCO₃-) cause an increase in plasma pH (alkalosis), those having a SID lower than HCO₃- cause a decrease in plasma pH (acidosis), while crystalloids with a SID equal to HCO₃- leave pH unchanged, regardless of the extent of the dilution. Colloids and blood components are composed of a crystalloid solution as solvent, and the abovementioned rules partially hold true also for these fluids. The scenario is however complicated by the possible presence of weak anions (albumin, phosphates and gelatins) and their effect on plasma pH. The present manuscript summarises the characteristics of crystalloids, colloids, buffer solutions and blood components and reviews their effect on acid-base equilibrium. Understanding the composition of intravenous fluids, along with the application of simple physicochemical rules best described by Stewart's approach, are pivotal steps to fully elucidate and predict alterations of plasma acid-base equilibrium induced by fluid therapy.

  4. A novel mechanism for the oxidation reaction of VO2+ on a graphite electrode in acidic solutions

    NASA Astrophysics Data System (ADS)

    Wang, Wenjun; Fan, Xinzhuang; Liu, Jianguo; Yan, Chuanwei; Zeng, Chaoliu

    2014-09-01

    With the consideration of optimizing the performance of the all-vanadium redox flow battery (VRB), the oxidation reaction mechanism of VO2+ on a rotating graphite disk electrode has been investigated by potentiodynamic polarization in sulfuric acid solutions with various pH and vanadium concentrations. Furthermore, the reaction orders of VO2+ and H+ for the oxidation reaction of VO2+ have been calculated from the polarization results and compared with the theoretical results according to the possible reaction mechanisms available in the literature. However, a new oxidation reaction mechanism has been proposed to describe the oxidation of VO2+ at last, and the theoretic reaction orders of VO2+ and H+ based on the new mechanism are consistent with the experimental results when the electrochemical reaction is the rate-limited process. Moreover, a corresponding kinetic equation has been established for the oxidation reaction of VO2+ on a spectroscopically pure graphite electrode, and can be well used to predict the polarization behavior in V (IV) acidic solutions.

  5. Results of analysis of long-term SLR and GPS solutions made for geophysical purposes

    NASA Astrophysics Data System (ADS)

    Szafranek, K.; Schillak, S.; Araszkiewicz, A.; Figurski, M.; Lehmann, M.

    2012-12-01

    Up-to-date space geodesy investigations take full advantage of various techniques data joint processing. The poster presents solutions (time series of North, East, Up components) of selected stations, which adopted Satellite Laser Ranging (SLR) and Global Positioning System (GPS) techniques and which were gathering the data in the same time (from 1994 to 2011). Processing of both types of data was made according to Global Geodetic Observing System (GGOS) recommendations. The main goal was to obtain coordinates and their changes in time (velocities) basing on both techniques data gathered between 1994 and 2011 and to compare the results (until now, preliminary analysis for the period 1996-2001.5 were made). The station coordinates were determined for the for first day of each month (SLR technique) and for the middle of each week (GPS technique) . Monthly orbital arcs for laser observations were created basing on solutions from several SLR sites (observations to LAGEOS-1 and LAGEOS-2 satellites) with the best solutions quality and the highest amount of observations. For GNSS coordinates determination about 130 sites belonging to International GNSS Service (IGS) were selected: 30 with local ties to SLR sites and others basing on their geolocalization (length of the baselines) and solutions time series analysis. Mainly, core IGS stations with long observation history were used. Due to small number of GPS sites in the period 1996-2000 and long baselines between them, the network was divided into seven subnetworks which were processed separately. The station coordinates were expressed in ITRF2008 for the epoch of 2005 and compared to the catalogue values. The GPS solutions were reduced to the SLR markers positions using local ties. Velocities from GPS and SLR processing were determined by the means of linear regression and compared to the ITRF2008 and the NNR NUVEL 1A model. Solutions of both techniques were analyzed in order to verify agreement of both techniques and

  6. Multi-walled carbon nanotubes and poly(lactic acid) nanocomposite fibrous membranes prepared by solution blow spinning.

    PubMed

    Oliveira, Juliano E; Zucolotto, Valtencir; Mattoso, Luiz H C; Medeiros, Eliton S

    2012-03-01

    Nanocomposite fibers based on multi-walled carbon nanotubes (MWCNT) and poly(lactic acid) (PLA) were prepared by solution blow spinning (SBS). Fiber morphology was characterized by scanning electron microscopy (SEM) and optical microscopy (OM). Electrical, thermal, surface and crystalline properties of the spun fibers were evaluated, respectively, by conductivity measurements (4-point probe), thermogravimetric analyses (TGA), differential scanning calorimetry (DSC), contact angle and X-ray diffraction (XRD). OM analysis of the spun mats showed a poor dispersion of MWCNT in the matrix, however dispersion in solution was increased during spinning where droplets of PLA in solution loaded with MWCNT were pulled by the pressure drop at the nozzle, producing PLA fibers filled with MWCNT. Good electrical conductivity and hydrophobicity can be achieved at low carbon nanotube contents. When only 1 wt% MWCNT was added to low-crystalline PLA, surface conductivity of the composites increased from 5 x 10(-8) to 0.46 S/cm. Addition of MWCNT can slightly influence the degree of crystallinity of PLA fibers as studied by XRD and DSC. Thermogravimetric analyses showed that MWCNT loading can decrease the onset degradation temperature of the composites which was attributed to the catalytic effect of metallic residues in MWCNT. Moreover, it was demonstrated that hydrophilicity slightly increased with an increase in MWCNT content. These results show that solution blow spinning can also be used to produce nanocomposite fibers with many potential applications such as in sensors and biosensors. PMID:22755116

  7. Simultaneous treatment of chlorinated organics and removal of metals and radionuclides with bimetals and complexing acids - application to surfactant solutions

    SciTech Connect

    Korte, N.E.; Gu, B.

    1997-10-01

    Currently available methods for separation and treatment of radioactive mixed waste are typically energy-intensive, and often require high temperatures. Passive methods that operate at ambient temperatures are needed. The purpose of this task is to develop bimetallic substrates, using a base metal such as iron and a promoter metal such as palladium (Pd), to provide a passive, low-energy solution to a substantial portion of DOE`s mixed-waste problem. This technology consists of a porous medium that can simultaneously dechlorinate hazardous organics such as TCE and polychlorinated biphenyls (PCBs) at the same time that it removes metallic and hazardous wastes from a solvent/surfactant solution. The porous medium consists of a bimetallic substrate such as palladized iron (Pd/Fe). Palladium is readily chemically plated on iron and preliminary studies suggest that only 0.05 to 0.1% Pd is needed for an efficient reaction. Thus, the cost of the material is reasonable especially is it is long-lived or can be regenerated. Field implementation would consist of the passage of a surfactant-laden, mixed waste through a column or bed of the bimetallic substrate. The organic component of this mixed waste may contain semivolatile compounds such as PCBs or pesticides and herbicides. The bimetal simultaneously removes radionuclides and metals and degrades halogenated hydrocarbons. Virtually any concentration can be treated. Following reaction of the bimetal with the waste stream, the resulting effluent will consist of an uncontaminated aqueous solution of surfactant or solvent that can be reused. The bimetal would then be rinsed with a dilute mineral acid or a mild complexing acid (e.g., oxalic or citric acid) to regenerate the surface and to remove sorbed metals and non-hazardous organic residue. The latter effluent would be low-level radioactive waste in some cases, but it would now be much easier to manage and be of a lower volume than the original mixed waste.

  8. Non-adiabatic tapered optical fiber sensor for measuring the interaction between α-amino acids in aqueous carbohydrate solution

    NASA Astrophysics Data System (ADS)

    Zibaii, M. I.; Latifi, H.; Karami, M.; Gholami, M.; Hosseini, S. M.; Ghezelayagh, M. H.

    2010-10-01

    A single-mode non-adiabatic tapered optical fiber (NATOF) sensor was utilized for sensing the variation in refractive index (RI) with concentration of d-glucose in deionized water and measurement of the RI of amino acids (AAs) in carbohydrate solutions. This method showed a rewarding ability in understanding the basis of biomolecular interactions in biological systems. Due to high sensitivity, ease of application, low cost and real-time measurement, this method is more efficient in comparison with other techniques, such as calorimetric titration, NMR, UV absorption spectroscopy, x-ray crystallography, computer calculations, kinetic studies and chromatography data. The NATOF is fabricated by the heat pulling method, utilizing a CO2 laser. The limit of detection of the NATOF was 55 ppm for a d-glucose concentration ranging from 0 to 80 mg ml-1, and the limit of detection of the RI measurement corresponding to these concentrations in the range from 1.3330 to 1.3447 was 8.2 × 10-6 as a refractometer sensor. The response of the NATOF shows that different kinds of interactions of various groups of AAs, such as l-alanine, l-leucine and l-cysteine with d-glucose, sucrose and water molecules, depend on functional groups in AAs such as OH, SH, CH2, NH+3 and COO-. These results can be interpreted in terms of solute-solute and solute-solvent interactions and the structure making/breaking ability of solutes in the given solution. Such a study helps in the better understanding of the interactions occurring between AA molecules and entities present in biological matrices.

  9. Fluoro- and perfluoralkylsulfonylpentafluoroanilides: synthesis and characterization of NH acids for weakly coordinating anions and their gas-phase and solution acidities.

    PubMed

    Kögel, Julius F; Linder, Thomas; Schröder, Fabian G; Sundermeyer, Jörg; Goll, Sascha K; Himmel, Daniel; Krossing, Ingo; Kütt, Karl; Saame, Jaan; Leito, Ivo

    2015-04-01

    Fluoro- and perfluoralkylsulfonyl pentafluoroanilides [HN(C6F5)(SO2X); X = F, CF3, C4F9, C8F17] are a class of imides with two different strongly electron-withdrawing substituents attached to a nitrogen atom. They are NH acids, the unsymmetrical hybrids of the well-known symmetrical bissulfonylimides and bispentafluorophenylamine. The syntheses, the structures of these perfluoroanilides, their solvates, and some selected lithium salts give rise to a structural variety beyond the symmetrical parent compounds. The acidities of representative subsets of these novel NH acids have been investigated experimentally and quantum-chemically and their gas-phase acidities (GAs) are reported, as well as the pKa values of these compounds in acetonitrile (MeCN) and DMSO solution. In quantum chemical investigations with the vertical and relaxed COSMO cluster-continuum models (vCCC/rCCC), the unusual situation is encountered that the DMSO-solvated acid Me2SO-H-N(SO2CF3)2, optimized in the gas phase (vCCC model), dissociates to Me2SO-H(+)-N(SO2CF3)2(-) during structural relaxation and full optimization with the solvation model turned on (rCCC model). This proton transfer underlines the extremely high acidity of HN(SO2CF3)2. The importance of this effect is studied computationally in DMSO and MeCN solution. Usually this effect is less pronounced in MeCN and is of higher importance in the more basic solvent DMSO. Nevertheless, the neglect of the structural relaxation upon solvation causes typical changes in the computational pKa values of 1 to 4 orders of magnitude (4-20 kJ mol(-1)). The results provide evidence that the published experimental DMSO pKa value of HN(SO2CF3)2 should rather be interpreted as the pKa of a Me2SO-H(+)-N(SO2CF3)2(-) contact ion pair. PMID:25727401

  10. Fluoro- and perfluoralkylsulfonylpentafluoroanilides: synthesis and characterization of NH acids for weakly coordinating anions and their gas-phase and solution acidities.

    PubMed

    Kögel, Julius F; Linder, Thomas; Schröder, Fabian G; Sundermeyer, Jörg; Goll, Sascha K; Himmel, Daniel; Krossing, Ingo; Kütt, Karl; Saame, Jaan; Leito, Ivo

    2015-04-01

    Fluoro- and perfluoralkylsulfonyl pentafluoroanilides [HN(C6F5)(SO2X); X = F, CF3, C4F9, C8F17] are a class of imides with two different strongly electron-withdrawing substituents attached to a nitrogen atom. They are NH acids, the unsymmetrical hybrids of the well-known symmetrical bissulfonylimides and bispentafluorophenylamine. The syntheses, the structures of these perfluoroanilides, their solvates, and some selected lithium salts give rise to a structural variety beyond the symmetrical parent compounds. The acidities of representative subsets of these novel NH acids have been investigated experimentally and quantum-chemically and their gas-phase acidities (GAs) are reported, as well as the pKa values of these compounds in acetonitrile (MeCN) and DMSO solution. In quantum chemical investigations with the vertical and relaxed COSMO cluster-continuum models (vCCC/rCCC), the unusual situation is encountered that the DMSO-solvated acid Me2SO-H-N(SO2CF3)2, optimized in the gas phase (vCCC model), dissociates to Me2SO-H(+)-N(SO2CF3)2(-) during structural relaxation and full optimization with the solvation model turned on (rCCC model). This proton transfer underlines the extremely high acidity of HN(SO2CF3)2. The importance of this effect is studied computationally in DMSO and MeCN solution. Usually this effect is less pronounced in MeCN and is of higher importance in the more basic solvent DMSO. Nevertheless, the neglect of the structural relaxation upon solvation causes typical changes in the computational pKa values of 1 to 4 orders of magnitude (4-20 kJ mol(-1)). The results provide evidence that the published experimental DMSO pKa value of HN(SO2CF3)2 should rather be interpreted as the pKa of a Me2SO-H(+)-N(SO2CF3)2(-) contact ion pair.

  11. Removal of dicyclohexyl acetic acid from aqueous solution using ultrasound, ozone and their combination.

    PubMed

    Kumar, Pardeep; Headley, John; Peru, Kerry; Bailey, Jon; Dalai, Ajay

    2014-01-01

    Naphthenic acids are a complex mixture of organic components, some of which include saturated alkyl-substituted cycloaliphatic carboxylic acids and acyclic aliphatic acids. They are naturally found in hydrocarbon deposits like oil sand, petroleum, bitumen and crude oil. In this study, the oxidation of a relatively high molecular weight naphthenic acid (Dicyclohexyl acetic acid) was investigated using ozonation, ultrasonication and hydrogen peroxide alone and their combinations. Effects on oxidation of dicyclohexyl acetic acid (DAA) were measured for different concentrations of ozone ranging between 0.7 to 3.3 mg L(-1) and pH in the range 6 to 10. Ultrasonication and hydrogen peroxide alone were not effective to oxidize dicyclohexyl acetic acid, but combining ultrasonication with H2O2 had a significant effect on oxidation of dicyclohexyl acetic acid with maximum removal reaching to 84 ± 2.2% with 81 ± 2.1% reduction in chemical oxygen demand (COD). Synergistic effects were observed for combining ultrasonication with ozonation and resulted in 100% DAA removal with 98 ± 0.8% reduction in COD within 15 min at 3.3 mg L(-1) ozone concentration and 130 Watts ultrasonication power. The reaction conditions obtained for the maximum oxidation of DAA and COD removal were used for the degradation of naphthenic acids mixture extracted from oil sands process water (OSPW). The percentage oxidation of NAs mixture extracted from OSPW was 89.3 ± 1.1% in ozonation and combined ozonation and ultrasonication, but COD removal observed was 65 ± 1.2% and 78 ± 1.4% for ozonation and combined ozonation and ultrasonication treatments, respectively.

  12. Recovery of acetic acid from dilute aqueous solutions using catalytic dehydrative esterification with ethanol.

    PubMed

    Yagyu, Daisuke; Ohishi, Tetsuo; Igarashi, Takeshi; Okumura, Yoshikuni; Nakajo, Tetsuo; Mori, Yuichiro; Kobayashi, Shū

    2013-03-01

    We have developed a direct esterification of aqueous acetic acid with ethanol (molar ratio=1:1) catalyzed by polystyrene-supported or homogeneous sulfonic acids toward the recovery of acetic acid from wastewater in chemical plants. The equilibrium yield was significantly increased by the addition of toluene, which had a high ability to extract ethyl acetate from the aqueous phase. It was shown that low-loading and alkylated polystyrene-supported sulfonic acid efficiently accelerated the reaction. These results suggest that the construction of hydrophobic reaction environments in water was critical in improving the chemical yield. Addition of inorganic salts was also effective for the reaction under not only biphasic conditions (toluene-water) but also toluene-free conditions, because the mutual solubility of ethyl acetate and water was suppressed by the salting-out effect. Among the tested salts, CaCl(2) was found to be the most suitable for this reaction system. PMID:23290939

  13. Control of Listeria monocytogenes on frankfurters by dipping in hops beta acids solutions.

    PubMed

    Shen, Cangliang; Geornaras, Ifigenia; Kendall, Patricia A; Sofos, John N

    2009-04-01

    Hops beta acids (HBA) are parts of hops flowers used in beer brewing and have shown antilisterial activity in bacteriological broth. The U.S. Department of Agriculture, Food Safety and Inspection Service has approved HBA for use to control Listeria monocytogenes on ready-to-eat meat products. This study evaluated the effects of HBA as dipping solutions to control L. monocytogenes during storage of frankfurters. Frankfurters (two replicates and three samples each) were inoculated (1.9 +/- 0.1 log CFU/cm2) with L. monocytogenes (10-strain mixture), dipped (2 min, 25 +/- 2 degrees C) in HBA solutions (0.03, 0.06, and 0.10%) or distilled water, and then vacuum packaged and stored at 4 or 10 degrees C for up to 90 and 48 days, respectively. Samples were periodically analyzed for microbial survival and growth on tryptic soy agar plus 0.6% yeast extract and PALCAM agar. Dipping in HBA solutions caused immediate L. monocytogenes reductions (P < 0.05) of 1.3 to 1.6 log CFU/cm2, whereas distilled water reduced counts by 1.0 log CFU/cm2. Pathogen growth was completely suppressed (P < 0.05) for 30 to 50 (4 degrees C) or 20 to 28 (10 degrees C) days on frankfurters dipped in HBA solutions, with antilisterial effects increasing with higher concentrations (0.03 to 0.10%). Fitting the data with the Baranyi model confirmed that the lag-phase duration of the pathogen was extended, and the growth rate was decreased on samples dipped in HBA solutions. Therefore, HBA may be considered for use to improve the microbial safety of ready-to-eat meat products, provided that future studies show no adverse effects on sensory qualities and that their use is economically feasible.

  14. Control of Listeria monocytogenes on frankfurters by dipping in hops beta acids solutions.

    PubMed

    Shen, Cangliang; Geornaras, Ifigenia; Kendall, Patricia A; Sofos, John N

    2009-04-01

    Hops beta acids (HBA) are parts of hops flowers used in beer brewing and have shown antilisterial activity in bacteriological broth. The U.S. Department of Agriculture, Food Safety and Inspection Service has approved HBA for use to control Listeria monocytogenes on ready-to-eat meat products. This study evaluated the effects of HBA as dipping solutions to control L. monocytogenes during storage of frankfurters. Frankfurters (two replicates and three samples each) were inoculated (1.9 +/- 0.1 log CFU/cm2) with L. monocytogenes (10-strain mixture), dipped (2 min, 25 +/- 2 degrees C) in HBA solutions (0.03, 0.06, and 0.10%) or distilled water, and then vacuum packaged and stored at 4 or 10 degrees C for up to 90 and 48 days, respectively. Samples were periodically analyzed for microbial survival and growth on tryptic soy agar plus 0.6% yeast extract and PALCAM agar. Dipping in HBA solutions caused immediate L. monocytogenes reductions (P < 0.05) of 1.3 to 1.6 log CFU/cm2, whereas distilled water reduced counts by 1.0 log CFU/cm2. Pathogen growth was completely suppressed (P < 0.05) for 30 to 50 (4 degrees C) or 20 to 28 (10 degrees C) days on frankfurters dipped in HBA solutions, with antilisterial effects increasing with higher concentrations (0.03 to 0.10%). Fitting the data with the Baranyi model confirmed that the lag-phase duration of the pathogen was extended, and the growth rate was decreased on samples dipped in HBA solutions. Therefore, HBA may be considered for use to improve the microbial safety of ready-to-eat meat products, provided that future studies show no adverse effects on sensory qualities and that their use is economically feasible. PMID:19435215

  15. Kinetics of CO2 Absorption into Aqueous Basic Amino Acid Salt: Potassium Salt of Lysine Solution.

    PubMed

    Shen, Shufeng; Yang, Ya-nan; Bian, Yangyang; Zhao, Yue

    2016-02-16

    Aqueous amino acid salts are considered as an attractive alternative to alkanolamine solvents (e.g., MEA) for carbon dioxide (CO2) absorption. The kinetics of CO2 into unloaded aqueous solutions of potassium lysinate (LysK) was studied using a wetted wall column at concentrations ranging from 0.25 to 2.0 M and temperatures from 298 to 333 K. Physicochemical properties of aqueous LysK solutions such as density, viscosity, and physical solubility of CO2 were measured to evaluate the reaction rate constants. The reaction pathway is described using zwitterion mechanism taking into account the effect of ionic strength on the reaction rate. Under the fast pseudo-first-order regime, the reaction rate parameters were obtained and correlated in a power-law reaction rate expression. LysK shows higher chemical reactivity toward CO2 than the industrial standard MEA and most of amino acid salts. Its reaction rate constants increase considerably with concentration and temperature. The reaction order is found to be an average value of 1.58 with respect to LysK. The forward second-order kinetic rate constant, k2 0 , are obtained as 31615 and 84822 m3 kmol−1 s−1 at 298 and 313 K, respectively with activation energy of 51.0 kJ mol−1. The contribution of water to the zwitterion deprotonation seems to be more significant than that of LysK for the above-mentioned kinetic conditions PMID:26751093

  16. Separation of Technetium in Nitric Acid Solution With an Extractant Impregnated Resin

    SciTech Connect

    Jei Kwon Moon; Eil Hee Lee; Chong-Hun Jung; Byung Chul Lee

    2006-07-01

    An extractant impregnated resin (EIR) was prepared by impregnation of Aliquat 336 into Amberlite XAD-4 for separation of technetium from rhodium in nitric acid solution. The prepared EIR showed high preference for rhenium (chemical analogue of technetium) over rhodium. The adsorption isotherms for rhenium were described well by Langmuir equation in both the single and multi-component systems. Maximum adsorption capacities obtained by modelling the isotherms of rhenium were 2.01 meq g{sup -1} and 1.97 meq g{sup -1} for the single and the multi-component systems, respectively. Column tests were also performed to confirm the separation efficiency of rhenium using a jacketed glass column (diam. 11 x L 150). The EIR column showed successful separation of rhenium with the breakthrough volume of about 122 BV for the breakthrough concentration of 0.08. Also the breakthrough data were modelled successfully by assuming a homogeneous diffusion model in the particle phase. The diffusivities obtained from the modelling were in the order of 10{sup -7} cm{sup 2} min{sup -1} for a rhenium. The rhenium adsorbed on the bed could be eluted with a high purity by using a nitric acid solution. (authors)

  17. Oxidation of trace amounts of transplutonium elements to the tetravalent state in solutions of mineral acids and their stabilities

    SciTech Connect

    Milyukova, M.S.; Varezhkina, N.S.; Kuzovkina, E.V.; Malikov, D.A.; Myasoedov, B.F.

    1989-01-01

    The behavior of trace amounts of americium(IV) in sulfuric and nitric acid solutions as a function of the mineral acid, potassium phosphotungstate, and ammonium persulfate concentrations was investigated. The stability of americium(IV) was studied. The optimal conditions and time of oxidation of trace amounts of americium to the tetravalent state were found on the basis of the experimental data obtained.

  18. Control of skin colour and polyphenol oxidase activity in santol fruit by dipping in organic acid solution.

    PubMed

    Benjawan, Chutichudet; Chutichudet, P

    2009-06-01

    This laboratory experiment was carried out at the Department of Agricultural Technology, Mahasarakham University, Northeast Thailand during July and August 2008. The experiment aimed to determine an effective natural organic acid that would delay the unattractive skin browning of santol fruit, while at the same time not damaging the quality of the fruit. The experiment included a study of the fruit's polyphenol oxidase (PPO) activity, phenolic content and quinone content, as they relate to colour and a study of total soluble solid content, pH, titratable acidity and vitamin C content as they relate to fruit quality. A Completely Randomized Design (CRD) with four replications was used. Each replication consisted of 10 fruits. Santol fruit was harvested at 145 days after full bloom and dipped for 30 min in aqueous solutions of two organic acids that were used as treatments, i.e., 0% for T1 (control), 5% citric acid for T2, 5% ascorbic acid for T3, 10% citric acid for T4 and 10% ascorbic acid for T5 and stored at room temperature (28 degrees C, 90% R.H.) to investigate the effect of the acid on fruit weight, skin colour, PPO activity and other internal parameters. The results showed that the most appropriate anti-browning agent for santol fruit was found with T2. It gave the highest mean values, 57.37 and 55.95, of brightness (L*) at 4 and 10 Days After Storage (DAS), respectively. In addition, PPO activity of flesh tissue was lowest for T2 with mean values of 0.0078 to 0.0092 by 0 and 300 S, respectively. The phenolic content in the flesh tissue significantly increased with an increase in numbers ofDAS, whereas the reverse was found with the pH level in the fruits. They were lowest for T2, with mean values of 6.00, by 10 DAS. There were no significant differences among the treatments in any of the measured Total Soluble Solids (TSS), Titratable Acidity (TA) and vitamin C content.

  19. An iwatsubo-based solution for labyrinth seals - comparison with experimental results

    NASA Technical Reports Server (NTRS)

    Childs, D. W.; Scharrer, J. K.

    1984-01-01

    The basic equations are derived for compressible flow in a labyrinth seal. The flow is assumed to be completely turbulent in the circumferential direction where the friction factor is determined by the Blasius relation. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equation. The first-order equations are solved by a separation of variables solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are compared to published test results.

  20. Desorption of 137Cs from Brachythecium mildeanum moss using acid solutions with pH 4.60-6.50

    NASA Astrophysics Data System (ADS)

    Čučulović, Ana; Veselinović, Dragan

    2015-12-01

    The desorption of 137Cs from the moss Brachythecium mildeanum (Schimp.) was performed using the following solutions: H2SO4 ( I), HNO3 ( II), H2SO4 + HNO3 ( III) with pH values of 4.60, 5.15, and 5.75, respectively, as well as distilled water (D) with pH 6.50. After five successive desorptions, each lasting 24 h, 20.5-37.6% 137Cs was desorbed from the moss using these solutions, while 30.7% of the starting content was desorbed using distilled water. The first desorption removed the highest percent of the original content of 137Cs in the moss (11.3-18.4%). This was determined by measuring 137Cs activity. If the current results are compared with those obtained earlier it may be concluded that 137Cs desorption from mosses is not species-dependent. The obtained results indicate the necessity of investigating the influence of acid rain, or rather, of H+ ions, on desorption of other ions from biological systems, i.e., the role of H+ ions in spreading other polluting compounds and thus producing secondary environmental pollution. From the results of this study it follows that acid rain will lead, through H+ ion action, to a similar increasing pollution of fallout waters with other ionic compounds which may not be present in the water before the contact with the plants and thus enable the pollution spreading. In the investigated system, the replacement of H+ ions from acid rains by more dangerous radioactive ions occured, increasing the concentration of the radioactive ions in the water, which demonstrates that the same process takes place in fallout water.