Thermal treatment of electronic waste in a fluidised bed and chemical digestion of solid products.

PubMed

Woynarowska, Amelia; Żukowski, Witold; Żelazny, Sylwester

2016-07-01

The article presents the results of e-waste thermal treatment in a fluidised bed reactor and solid products digestion under acidic conditions. During the processes, measurements of carbon monoxide, carbon dioxide, volatile organic compounds, nitrogen oxides, sulphur dioxide, hydrogen chloride, hydrogen bromide, hydrogen cyanide, ammonia, phenol, aliphatic and aromatic hydrocarbons, hydrogen fluoride and phosgene were carried out. Several digestion tests of the solid residue in sulphuric acid (VI) at 25 °C-65 °C, for 55 min-24 h were conducted. In each case, the dilution method was used, i.e. preliminary digestion in concentrated sulphuric acid (VI) (95%) for 40 min, and then dilution to expected concentrations (30%-50%). Most preferred results were obtained using sulphuric acid (VI) with a target concentration of 40% at 65 °C, where the leaching degrees were 76.56% for copper, 71.67% for iron, 91.89% for zinc and 97.40% for tin. The time necessary to effectively carry out the digestion process was 220 min. © The Author(s) 2016.

Epoxidation of cottonseed oil by aqueous hydrogen peroxide catalysed by liquid inorganic acids.

PubMed

Dinda, Srikanta; Patwardhan, Anand V; Goud, Vaibhav V; Pradhan, Narayan C

2008-06-01

The kinetics of epoxidation of cottonseed oil by peroxyacetic acid generated in situ from hydrogen peroxide and glacial acetic acid in the presence of liquid inorganic acid catalysts were studied. It was possible to obtain up to 78% relative conversion to oxirane with very less oxirane cleavage by in situ technique. The rate constants for sulphuric acid catalysed epoxidation of cottonseed oil were in the range 0.39-5.4 x 10(-6)L mol(-1)s(-1) and the activation energy was found to be 11.7 kcal mol(-1). Some thermodynamic parameters such as enthalpy, entropy, and free energy of activation were determined to be of 11.0 kcal mol(-1), -51.4 cal mol(-1)K(-1) and 28.1 kcal mol(-1), respectively. The order of effectiveness of catalysts was found to be sulphuric acid>phosphoric acid>nitric acid>hydrochloric acid. Acetic acid was found to be superior to formic acid for the in situ cottonseed oil epoxidation.

Phosphorus recovery and leaching of trace elements from incinerated sewage sludge ash (ISSA).

PubMed

Fang, Le; Li, Jiang-Shan; Guo, Ming Zhi; Cheeseman, C R; Tsang, Daniel C W; Donatello, Shane; Poon, Chi Sun

2018-02-01

Chemical extraction of phosphorus (P) from incinerated sewage sludge ash (ISSA) is adversely influenced by co-dissolution of metals and metalloids. This study investigated P recovery and leaching of Zn, Cu, Pb, As and Ni from ISSA using inorganic acids (sulphuric acid and nitric acid), organic acids (oxalic acid and citric acid), and chelating agents (ethylenediaminetetraacetic acid (EDTA) and ethylene diamine tetramethylene phosphonate (EDTMP)). The aim of this study was to optimize a leaching process to recover P-leachate with high purity for P fertilizer production. The results show that both organic and inorganic acids extract P-containing phases but organic acids leach more trace elements, particularly Cu, Zn, Pb and As. Sulphuric acid was the most efficient for P recovery and achieved 94% of total extraction under the optimal conditions, which were 2-h reaction with 0.2 mol/L H 2 SO 4 at a liquid-to-solid ratio of 20:1. EDTA extracted only 20% of the available P, but the leachates were contaminated with high levels of trace elements under optimum conditions (3-h reaction with EDTA at 0.02 mol/L, pH 2, and liquid-to-solid ratio of 20:1). Therefore, EDTA was considered an appropriate pre-treatment agent for reducing the total metal/metalloid content in ISSA, which produced negligible changes in the structure of ISSA and reduced contamination during subsequent P extraction using sulphuric acid. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lehtipalo, Katrianne; Rondo, Linda; Kontkanen, Jenni

The growth of freshly formed aerosol particles can be the bottleneck in their survival to cloud condensation nuclei. It is therefore crucial to understand how particles grow in the atmosphere. Insufficient experimental data has impeded a profound understanding of nano-particle growth under atmospheric conditions. Here we study nano-particle growth in the CLOUD (Cosmics Leaving OUtdoors Droplets) chamber, starting from the formation of molecular clusters. We present measured growth rates at sub-3 nm sizes with different atmospherically relevant concentrations of sulphuric acid, water, ammonia and dimethylamine. We find that atmospheric ions and small acid-base clusters, which are not generally accounted formore » in the measurement of sulphuric acid vapour, can participate in the growth process, leading to enhanced growth rates. The availability of compounds capable of stabilizing sulphuric acid clusters governs the magnitude of these effects and thus the exact growth mechanism. Furthermore, we bring these observations into a coherent framework and discuss their significance in the atmosphere.« less

Characterization of Used MIL-L-7808 Lubricants.

DTIC Science & Technology

1985-05-01

Gravimetric Finish 20 2.3.3 Separation of Mineral Oil by means of Sulphuric Acid 21 2.3.4 Rolls-Royce Method 1032 26 2.3.5 Conclusion 26 3 Minimum...and STM No. 1 i Application of Sulphuric Acid Method for MOC to:- IV Standards based upon ATL.9100 23 V Standards based upon ATL.9101 24 VI Standards...total acid numbers of the standards before, and after application of each technique. Considering firstly the volatile contaminant contents obtained by STM

A further study on the dietary-regulated biosynthesis of high-sulphur wool proteins

PubMed Central

Gillespie, J. M.; Broad, Andrea; Reis, P. J.

1969-01-01

When the diet of sheep is supplemented by the infusion of sulphur-containing amino acids or casein into the abomasum, the newly synthesized wool shows characteristic changes in its amino acid composition, with significant increases in cystine, proline and serine and decreases in aspartic acid and phenylalanine. This modification seems to be due entirely to an alteration in the overall composition of the high-sulphur proteins and to an increase in their proportion in the fibre. These variations are not the result of a change in the composition of individual proteins, but are due to alterations in their relative proportions and to the initiation of the synthesis of `new' proteins, many of which are extremely rich in cystine. It is suggested that the heterogeneity of the high-sulphur proteins may be due, in part, to similar changes in composition caused by natural variations in the nutrition of sheep. ImagesFig. 3.Fig. 4. PMID:5774505

Comparison of the impacts of acid and nitrogen additions on carbon fluxes in European conifer and broadleaf forests.

PubMed

Oulehle, Filip; Tahovská, Karolina; Chuman, Tomáš; Evans, Chris D; Hruška, Jakub; Růžek, Michal; Bárta, Jiří

2018-07-01

Increased reactive nitrogen (N) loadings to terrestrial ecosystems are believed to have positive effects on ecosystem carbon (C) sequestration. Global "hot spots" of N deposition are often associated with currently or formerly high deposition of sulphur (S); C fluxes in these regions might therefore not be responding solely to N loading, and could be undergoing transient change as S inputs change. In a four-year, two-forest stand (mature Norway spruce and European beech) replicated field experiment involving acidity manipulation (sulphuric acid addition), N addition (NH 4 NO 3 ) and combined treatments, we tested the extent to which altered soil solution acidity or/and soil N availability affected the concentration of soil dissolved organic carbon (DOC), soil respiration (Rs), microbial community characteristics (respiration, biomass, fungi and bacteria abundances) and enzyme activity. We demonstrated a large and consistent suppression of soil water DOC concentration driven by chemical changes associated with increased hydrogen ion concentrations under acid treatments, independent of forest type. Soil respiration was suppressed by sulphuric acid addition in the spruce forest, accompanied by reduced microbial biomass, increased fungal:bacterial ratios and increased C to N enzyme ratios. We did not observe equivalent effects of sulphuric acid treatments on Rs in the beech forest, where microbial activity appeared to be more tightly linked to N acquisition. The only changes in C cycling following N addition were increased C to N enzyme ratios, with no impact on C fluxes (either Rs or DOC). We conclude that C accumulation previously attributed solely to N deposition could be partly attributable to their simultaneous acidification. Copyright © 2018 Elsevier Ltd. All rights reserved.

The effect of acid–base clustering and ions on the growth of atmospheric nano-particles

DOE PAGES

Lehtipalo, Katrianne; Rondo, Linda; Kontkanen, Jenni; ...

2016-05-20

The growth of freshly formed aerosol particles can be the bottleneck in their survival to cloud condensation nuclei. It is therefore crucial to understand how particles grow in the atmosphere. Insufficient experimental data has impeded a profound understanding of nano-particle growth under atmospheric conditions. Here we study nano-particle growth in the CLOUD (Cosmics Leaving OUtdoors Droplets) chamber, starting from the formation of molecular clusters. We present measured growth rates at sub-3 nm sizes with different atmospherically relevant concentrations of sulphuric acid, water, ammonia and dimethylamine. We find that atmospheric ions and small acid-base clusters, which are not generally accounted formore » in the measurement of sulphuric acid vapour, can participate in the growth process, leading to enhanced growth rates. The availability of compounds capable of stabilizing sulphuric acid clusters governs the magnitude of these effects and thus the exact growth mechanism. Furthermore, we bring these observations into a coherent framework and discuss their significance in the atmosphere.« less

The effect of acid–base clustering and ions on the growth of atmospheric nano-particles

PubMed Central

Lehtipalo, Katrianne; Rondo, Linda; Kontkanen, Jenni; Schobesberger, Siegfried; Jokinen, Tuija; Sarnela, Nina; Kürten, Andreas; Ehrhart, Sebastian; Franchin, Alessandro; Nieminen, Tuomo; Riccobono, Francesco; Sipilä, Mikko; Yli-Juuti, Taina; Duplissy, Jonathan; Adamov, Alexey; Ahlm, Lars; Almeida, João; Amorim, Antonio; Bianchi, Federico; Breitenlechner, Martin; Dommen, Josef; Downard, Andrew J.; Dunne, Eimear M.; Flagan, Richard C.; Guida, Roberto; Hakala, Jani; Hansel, Armin; Jud, Werner; Kangasluoma, Juha; Kerminen, Veli-Matti; Keskinen, Helmi; Kim, Jaeseok; Kirkby, Jasper; Kupc, Agnieszka; Kupiainen-Määttä, Oona; Laaksonen, Ari; Lawler, Michael J.; Leiminger, Markus; Mathot, Serge; Olenius, Tinja; Ortega, Ismael K.; Onnela, Antti; Petäjä, Tuukka; Praplan, Arnaud; Rissanen, Matti P.; Ruuskanen, Taina; Santos, Filipe D.; Schallhart, Simon; Schnitzhofer, Ralf; Simon, Mario; Smith, James N.; Tröstl, Jasmin; Tsagkogeorgas, Georgios; Tomé, António; Vaattovaara, Petri; Vehkamäki, Hanna; Vrtala, Aron E.; Wagner, Paul E.; Williamson, Christina; Wimmer, Daniela; Winkler, Paul M.; Virtanen, Annele; Donahue, Neil M.; Carslaw, Kenneth S.; Baltensperger, Urs; Riipinen, Ilona; Curtius, Joachim; Worsnop, Douglas R.; Kulmala, Markku

2016-01-01

The growth of freshly formed aerosol particles can be the bottleneck in their survival to cloud condensation nuclei. It is therefore crucial to understand how particles grow in the atmosphere. Insufficient experimental data has impeded a profound understanding of nano-particle growth under atmospheric conditions. Here we study nano-particle growth in the CLOUD (Cosmics Leaving OUtdoors Droplets) chamber, starting from the formation of molecular clusters. We present measured growth rates at sub-3 nm sizes with different atmospherically relevant concentrations of sulphuric acid, water, ammonia and dimethylamine. We find that atmospheric ions and small acid-base clusters, which are not generally accounted for in the measurement of sulphuric acid vapour, can participate in the growth process, leading to enhanced growth rates. The availability of compounds capable of stabilizing sulphuric acid clusters governs the magnitude of these effects and thus the exact growth mechanism. We bring these observations into a coherent framework and discuss their significance in the atmosphere. PMID:27197574

Synthesis of Furfural from Water Hyacinth (Eichornia croassipes)

NASA Astrophysics Data System (ADS)

Ismiyarto; Ngadiwiyana; windarti, T.; Purbowatiningrum, RS; Hapsari, M.; Rafi'ah, FH; Suyanti; Haq, MS

2017-02-01

Furfural has been prepared from hydrolysis of dried biomass of water hyacinth (Eichornia crassipes) by using diluted hydrochloric acid and sulphuric acid as catalysts. This process involved the conversion of the pentosane fraction in water hyacinth into pentose, and then pentose was cyclodehydrated into furfural. The reaction was conducted in a distillation set with receiving the flask that contains chloroform. Furfural was identified by fehling test which was then characterized using Fourier Transform Infra Red (FTIR) and Proton Nuclear Magnetic Resonance (1H-NMR), followed by Gas Chromatography with Mass Spectroscopy (GC-MS). The yield of furfural obtained using sulphuric acid catalyst was 0.38% and hydrochloric acid catalyst was 0.01% of dried biomass.

Turning Biodiesel Waste Glycerol into 1,3-Propanediol: Catalytic Performance of Sulphuric acid-Activated Montmorillonite Supported Platinum Catalysts in Glycerol Hydrogenolysis.

PubMed

Samudrala, Shanthi Priya; Kandasamy, Shalini; Bhattacharya, Sankar

2018-05-10

Direct C-O hydrogenolysis of bioglycerine to produce 1,3-propanediol selectively is a vital technology that can expand the scope of biodiesel industry and green chemical production from biomass. Herein we report sulphuric acid-activated montmorillonite clay supported platinum nanoparticles as highly effective solid acid catalysts for the selective production of 1,3-propanediol from glycerol. The catalytic performances of the catalysts were investigated in the hydrogenolysis of glycerol with a fixed bed reactor under ambient pressure. The results were found promising and showed that the activation of montmorillonite by sulphuric acid incorporated Brønsted acidity in the catalyst and significantly improved the selectivity to 1,3-propanediol. The catalytic performance of different platinum loaded catalysts was examined and 2 wt% Pt/S-MMT catalyst presented superior activity among others validating 62% 1,3-propanediol selectivity at 94% glycerol conversion. The catalytic activity of 2Pt/S-MMT was systematically investigated under varying reaction parameters including reaction temperature, hydrogen flow rate, glycerol concentration, weight hourly space velocity, and contact time to derive the optimum conditions for the reaction. The catalyst stability, reusability and structure-activity correlation were also elucidated. The high performance of the catalyst could be ascribed to well disperse Pt nanoparticles immobilized on acid-activated montmorillonite, wider pore-structure and appropriate acid sites of the catalyst.

AGARD Corrosion Handbook. Volume 1. Aircraft Corrosion: Causes and Case Histories

DTIC Science & Technology

1985-07-01

Anodic coatings can be formed in chromic acid, sulphuric acid, phosphoric acid or oxalic acid solutions. Chromic acid anodizing is widely used with...and consists of a thin non-porous barrier layer next to the metal with a porous outer layer that can be sealed by hydrothermal treatment in steam...anaerobic) or an oxidative (aerobic) mechanism. Various organic acids such as citric acid, oxalic acid, gluconic acid, dodecanoic acid, etc., which may be

Analytical applications of condensed phosphoric acid-IV Iodometric determination of sulphur in sulphate and sulphide ores and minerals and other compounds after reduction with sodium hypophosphite and tin metal in condensed phosphoric acid.

PubMed

Mizoguchi, T; Ishii, H

1980-06-01

Sulphate in sulphate ores, e.g., alunite, anglesite, barytes, chalcanthite, gypsum, manganese sulphate ore, is reduced to hydrogen sulphide by the hypophosphite-tin metal-CPA method, if a slight modification is made. Sulphide ores, e.g., galena, sphalerite, are quantitatively decomposed with CPA alone to give hydrogen sulphide. Suitable reducing agents must be used for the quantitative recovery of hydrogen sulphide from pyrite, nickel sulphide, cobalt sulphide and cadmium sulphide, or elemental sulphur is liberated. Iodide must be used in the decomposition of chalcopyrite; the copper sulphide is too stable to be decomposed by CPA alone. Molybdenite is not decomposed in CPA even if reducing agents are added. The pretreatment methods for the determination of sulphur in sulphur oxyacids and elemental sulphur have also been investigated.

Biodegradation of the xenobiotic organic disulphide 4,4'-dithiodibutyric acid by Rhodococcus erythropolis strain MI2 and comparison with the microbial utilization of 3,3'-dithiodipropionic acid and 3,3'-thiodipropionic acid.

PubMed

Wübbeler, Jan Hendrik; Bruland, Nadine; Wozniczka, Milena; Steinbüchel, Alexander

2010-04-01

Application of the non-toxic 3,3'-thiodipropionic acid (TDP) and 3,3'-dithiodipropionic acid (DTDP) as precursors for the microbial production of polythioesters (PTEs), a class of biologically persistent biopolymers containing sulphur in the backbone, was successfully established previously. However, synthesis of PTEs containing 4-mercaptobutyrate (4MB) as building blocks could not be achieved. The very harmful 4MB is not used as a PTE precursor or as the carbon source for growth by any known strain. As a promising alternative, the harmless oxidized disulfide of two molecules of 4MB, 4,4'-dithiodibutyric acid (DTDB), was employed for enrichments of bacterial strains capable of biodegradation. Investigation of novel precursor substrates for PTEs and comparison of respective strains growing on TDP, DTDP and DTDB as sole carbon source was accomplished. A broad variety of bacteria capable of using one of these organic sulphur compounds were isolated and compared. TDP and DTDP were degraded by several strains belonging to different genera, whereas all DTDB-utilizing strains were affiliated to the species Rhodococcus erythropolis. Transposon mutagenesis of R. erythropolis strain MI2 and screening of 7500 resulting mutants yielded three mutants exhibiting impaired growth on DTDB. Physiological studies revealed production of volatile hydrogen sulphide and accumulation of significant amounts of 4MB, 4-oxo-4-sulphanylbutanoic acid and succinic acid in the culture supernatants. Based on this knowledge, a putative pathway for degradation of DTDB was proposed: DTDB could be cleaved into two molecules of 4MB, followed by an oxidation yielding 4-oxo-4-sulphanylbutanoic acid. A putative desulphydrase probably catalyses the abstraction of sulphur, thereby generating succinic acid and hydrogen sulphide.

Attenuation of Diabetes-induced Cardiac and Subcellular Defects by Sulphur-containing Amino Acids.

PubMed

Tappia, Paramjit S; Adameova, Adriana; Dhalla, Naranjan S

2018-01-30

Patients with diabetes mellitus have an increased risk of mortality due to cardiovascular complications. Supplementation with specific sulphur-containing amino acids is rapidly emerging as a possible therapeutic adjuvant for diabetes and associated cardiovascular complications. It is well-known that oxidative stress plays an important role in the pathogenesis of diabetes-induced cardiovascular disease, which is invariably associated with abnormal blood lipid profile, insulin resistance and other symptoms of metabolic syndrome. Cysteine and taurine are among the most common sulphur-containing amino acids and their cellular levels decline during diabetes that may contribute to the development of the cardiomyopathy. Although sulphur-containing agents exert multiple actions on cellular and subcellular functions in the heart, they also exhibit antioxidant properties and thus may exert beneficial effects in different pathophysiological conditions. It is concluded that reduction of oxidative stress by cysteine and taurine may serve as an important mechanism for the attenuation of diabetes-induced subcellular and functional abnormalities in the heart. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Acid rain and its ecological consequences.

PubMed

Singh, Anita; Agrawal, Madhoolika

2008-01-01

Acidification of rain-water is identified as one of the most serious environmental problems of transboundary nature. Acid rain is mainly a mixture of sulphuric and nitric acids depending upon the relative quantities of oxides of sulphur and nitrogen emissions. Due to the interaction of these acids with other constituents of the atmosphere, protons are released causing increase in the soil acidity Lowering of soil pH mobilizes and leaches away nutrient cations and increases availability of toxic heavy metals. Such changes in the soil chemical characteristics reduce the soil fertility which ultimately causes the negative impact on growth and productivity of forest trees and crop plants. Acidification of water bodies causes large scale negative impact on aquatic organisms including fishes. Acidification has some indirect effects on human health also. Acid rain affects each and every components of ecosystem. Acid rain also damages man-made materials and structures. By reducing the emission of the precursors of acid rain and to some extent by liming, the problem of acidification of terrestrial and aquatic ecosystem has been reduced during last two decades.

L-Cysteine-induced up-regulation of the low-density lipoprotein receptor is mediated via a transforming growth factor-alpha signalling pathway.

PubMed

Tanaka, Yuma; Shimada, Masaya; Nagaoka, Satoshi

2014-02-14

Sulphur-containing amino acids regulate plasma cholesterol levels in animals and humans. However, their mechanism of action remains unclear. Low-density lipoprotein receptor (LDLR) plays an important role in cholesterol metabolism. We therefore investigated the effects of sulphur-containing amino acids on the expression of LDLR in hepatocytes. HepG2 cells were cultured in Dulbecco's Modified Eagle's Medium with or without sulphur-containing amino acids and cysteine-containing compounds. We found that L-cysteine increased LDLR mRNA and enhanced LDLR gene promoter activity through the extracellular-signal-related kinase and p38 mitogen-activated protein kinase signalling pathways in HepG2 cells. Moreover, we observed that L-cysteine stimulated the release of transforming growth factor-alpha (TGF-α) and that TGF-α increased the LDLR mRNA levels. This study provides a report of the L-cysteine mediated up-regulation of the LDLR expression via TGF-α signalling pathway. Our findings provide insights into cholesterol homeostasis and amino acid signalling. Copyright © 2014 Elsevier Inc. All rights reserved.

Effect of sulphur dioxide on precipitation and on the sulphur content and acidity of soils in Alberta, Canada

Treesearch

M. Nyborg; J. Crepin; D. Hocking; J. Baker

1976-01-01

Rain and snow in Alberta are seldom acid. The S content of snow is so low that the snow pack gives a deposition of less than 1 kg S/ha, even downwind from large SO2 emission sources. Rainfall contributes at the most 4 kg S/ha yearly near SO2 sources, and only about 1 kg S/ha in clean areas. However, rain intercepted by...

Biodeterioration of the Cement Composites

NASA Astrophysics Data System (ADS)

Luptáková, Alena; Eštoková, Adriana; Mačingová, Eva; Kovalčíková, Martina; Jenčárová, Jana

2016-10-01

The destruction of natural and synthetic materials is the spontaneous and irreversible process of the elements cycling in nature. It can by accelerated or decelerated by physical, chemical and biological influences. Biological influences are represented by the influence of the vegetation and microorganisms (MO). The destruction of cement composites by different MO through the diverse mechanisms is entitled as the concrete biodeterioration. Several sulphur compounds and species of MO are involved in this complex process. Heterotrophic and chemolithotrophic bacteria together with fungi have all been found in samples of corroding cement composites. The MO involved in the process metabolise the presented sulphur compounds (hydrogen sulphide, elemental sulphur etc.) to sulphuric acid reacting with concrete. When sulphuric acid reacts with a concrete matrix, the first step involves a reaction between the acid and the calcium hydroxide forming calcium sulphate. This is subsequently hydrated to form gypsum, the appearance of which on the surface of concrete pipes takes the form of a white, mushy substance which has no cohesive properties. In the continuing attack, the gypsum would react with the calcium aluminate hydrate to form ettringite, an expansive product. The use supplementary cementing composite materials have been reported to improve the resistance of concrete to biodeterioration. The aim of this work was the study of the cement composites biodeterioration by the bacteria Acidithiobacillus thiooxidans. Experimental works were focused on the comparison of special cement composites and its resistance affected by the activities of used sulphur-oxidising

Determination of silver, antimony, bismuth, copper, cadmium and indium in ores, concentrates and related materials by atomic-absorption spectrophotometry after methyl isobutyl ketone extraction as iodides.

PubMed

Donaldson, E M; Wang, M

1986-03-01

Methods for determining ~ 0.2 mug g or more of silver and cadmium, ~ 0.5 mug g or more of copper and ~ 5 mug g or more of antimony, bismuth and indium in ores, concentrates and related materials are described. After sample decomposition and recovery of antimony and bismuth retained by lead and calcium sulphates, by co-precipitation with hydrous ferric oxide at pH 6.20 +/- 0.05, iron(III) is reduced to iron(II) with ascorbic acid, and antimony, bismuth, copper, cadmium and indium are separated from the remaining matrix elements by a single methyl isobutyl ketone extraction of their iodides from ~2M sulphuric acid-0.1M potassium iodide. The extract is washed with a sulphuric acid-potassium iodide solution of the same composition to remove residual iron and co-extracted zinc, and the extracted elements are stripped from the extract with 20% v v nitric acid-20% v v hydrogen peroxide. Alternatively, after the removal of lead sulphate by filtration, silver, copper, cadmium and indium can be extracted under the same conditions and stripped with 40% v v nitric acid-25% v v hydrochloric acid. The strip solutions are treated with sulphuric and perchloric acids and ultimately evaporated to dry ness. The individual elements are determined in a 24% v v hydrochloric acid medium containing 1000 mug of potassium per ml by atomic-absorption spectrophotometry with an air-acetylene flame. Tin, arsenic and molybdenum are not co-extracted under the conditions above. Results obtained for silver, antimony, bismuth and indium in some Canadian certified reference materials by these methods are compared with those obtained earlier by previously published methods.

Characterization of dross and its recovery by sulphuric acid leaching

NASA Astrophysics Data System (ADS)

Rahmani, S. A.; Meidianto, A.; Amal, M. I.; Wismogroho, A. S.; Widayatno, W. B.

2018-03-01

This paper reports the characterization of dross from galvanizing process and its recovery using acidic leaching method. The diffraction profile of dross showed identical peaks with that of ZnO. The X-ray Fluorescence (XRF) analysis identified the content of following metals: Zn, Fe, Mn, Ga, Co, and W. The thermal behaviour examination revealed the existence of some volatiles within the initial sample. The acidic leaching at various concentrations of sulphuric acid was conducted to determine the optimum concentration for zinc recovery and the highest yield of zinc sulphate. It is concluded that the optimum concentration of H2SO4 for this kind of dross is 4 M with 71.9% yield of ZnSO4. The result of leaching process was confirmed by infrared spectrum, where various absorptions corresponding to SO4 2- and Zn-O bands were observed.

Electrolytic Polishing and Etching Techniques for Preparing Specimens of Bismuth and Antimony and Their Alloys: Materials and Structures.

DTIC Science & Technology

Electrolytic polishing was performed in a solution of methyl alcohol, sulphuric acid , hydrocloric acid and ethylene glycol. Etching was done...electrolytically in a 5 percent chromic acid solution. Use of these techniques has permitted detailed studies of the microstructures of bismuth-antimony single

Review of the origin of sulphur in DN-1 discharge and its implication for future development, Dauin prospect, central Philippines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bayrante, L.F.; Hermoso, D.Z.; Candelaria, M.R.

1997-12-31

Well DN-1, the first exploratory well of the Dauin geothermal prospect discharged in 1983 substantial quantities of sulphur with a near-neutral pH fluid (pH 6.4 to 7.2) containing maximum chloride levels of 3,300 mg/kg, SO{sub 4} of 300 mg/kg; and high CO{sub 2} and H{sub 2}S relative to the production wells in Palinpinon Field to the north. The chemistry of DN-1 discharge-fluid and the origin of sulphur have been the cause of apprehension for any future development due to concerns on the presence of a possible acid resource southeast of Cuernos de Negros. A reinterpretation of the previous and newmore » surface data was undertaken in 1992 and 1996, including the origin of sulphur, to evaluate the potential of Dauin for development. The results indicate that the sulphur in DN-1 is formed from partial oxidation of hydrogen sulphide derived from the neutralised-acid fluids formed by sulphur hydrolysis at shallow levels but distant from DN-1. The study argues for the presence of near neutral exploitable resource in the prospect area.« less

Influence of metakaolin on chemical resistance of concrete

NASA Astrophysics Data System (ADS)

Mlinárik, L.; Kopecskó, K.

2013-12-01

Nowadays the most suitable and widely used construction material is concrete. We could develop concrete for every request in connection with the properties of fresh concrete and the quality of hardened concrete, too. The demand is rising in application of special concretes, like high performance and ultra high performance concretes (HPC, UHPC). These are usable in extreme natural circumstances or in very corrosive surroundings (for example: sewage farm, sewer, cooling tower, biogas factories). The pH value of the commercial sewage is between 7-8, but this value is often around 4 or less. The concrete pipes, which transport the sewage, are under corrosion, because above the liquid level sulphuric acid occurs due to microbes. Acidic surroundings could start the corrosion of concrete. When the pH value reduces, the influence of the acids will increase. The most significant influence has the sulphuric acid. The pH value of sulphuric acid is about 1, or less. Earlier in the cooling towers of coal thermal power stations used special coating on the concrete wall. Recently application of high performance concrete without polymeric coating is more general. Cementitious supplementary materials are widely used to protect the concrete from these corrosive surroundings. Usually used cementitious supplementary materials are ground granulated blastfurnace slag (GGBS), flying ash (FA) or silica fume (SF). In the last years there has been a growing interest in the application of metakaolin. Metakaolin is made by heat treatment, calcinations of a natural clay mineral, kaolinite. In our present research the chemical resistance of mortars in different corrosive surroundings (pH=1 sulphuric acid; pH=3 acetic acid) and the chloride ion migration were studied on series of mortar samples using rapid chloride migration test. Cement paste and mortar samples were made with 17% metakaolin replacement or without metakaolin. The following cements were used: CEM II/A-S 42.5 N, CEM I 42.5 N-S. We concluded that the replacement of cement by metakaolin results in significant increases in compressive and tensile strengths and it prevents the infiltration of harmful substances.

Usage of Neural Network to Predict Aluminium Oxide Layer Thickness

PubMed Central

Michal, Peter; Vagaská, Alena; Gombár, Miroslav; Kmec, Ján; Spišák, Emil; Kučerka, Daniel

2015-01-01

This paper shows an influence of chemical composition of used electrolyte, such as amount of sulphuric acid in electrolyte, amount of aluminium cations in electrolyte and amount of oxalic acid in electrolyte, and operating parameters of process of anodic oxidation of aluminium such as the temperature of electrolyte, anodizing time, and voltage applied during anodizing process. The paper shows the influence of those parameters on the resulting thickness of aluminium oxide layer. The impact of these variables is shown by using central composite design of experiment for six factors (amount of sulphuric acid, amount of oxalic acid, amount of aluminium cations, electrolyte temperature, anodizing time, and applied voltage) and by usage of the cubic neural unit with Levenberg-Marquardt algorithm during the results evaluation. The paper also deals with current densities of 1 A·dm−2 and 3 A·dm−2 for creating aluminium oxide layer. PMID:25922850

Usage of neural network to predict aluminium oxide layer thickness.

PubMed

Michal, Peter; Vagaská, Alena; Gombár, Miroslav; Kmec, Ján; Spišák, Emil; Kučerka, Daniel

2015-01-01

This paper shows an influence of chemical composition of used electrolyte, such as amount of sulphuric acid in electrolyte, amount of aluminium cations in electrolyte and amount of oxalic acid in electrolyte, and operating parameters of process of anodic oxidation of aluminium such as the temperature of electrolyte, anodizing time, and voltage applied during anodizing process. The paper shows the influence of those parameters on the resulting thickness of aluminium oxide layer. The impact of these variables is shown by using central composite design of experiment for six factors (amount of sulphuric acid, amount of oxalic acid, amount of aluminium cations, electrolyte temperature, anodizing time, and applied voltage) and by usage of the cubic neural unit with Levenberg-Marquardt algorithm during the results evaluation. The paper also deals with current densities of 1 A · dm(-2) and 3 A · dm(-2) for creating aluminium oxide layer.

Hydrothermal Alteration in an Acid-Sulphate Geothermal Field: Sulphur Springs, Saint Lucia

NASA Astrophysics Data System (ADS)

Joseph, E. P.; Barrett, T. J.

2017-12-01

Sulphur Springs is a vigorous geothermal field associated with the Soufrière Volcanic Centre in southern Saint Lucia. Bubbling hydrothermal pools are rich in sodium-calcium sulphate, with pHs of 3-7 and temperatures of 41-97ºC. Fumaroles have temperatures up to, and at times above, 100°C. Gases from bubbling pools and fumaroles have high contents of CO2 (601-993 mmol/mol) and H2S (3-190 mmol/mol). To investigate the nature and extent of hydrothermal alteration, detailed chemical analysis was carried out on 25 altered rocks, 10 sediments from pools and creeks in the main discharge area, and 15 little-altered rocks up to 2 km away from geothermal field. Eight altered samples were also analysed for stable isotope compositions, with mineralogy determined by X-ray diffraction and mineral liberation analysis. Least-altered host rocks comprise calc-alkaline feldspar-quartz-porphyritic dacites of near-uniform composition that form massive domes and volcaniclastic units. These rocks were emplaced 10-30 Ka ago (Lindsay et al. 2013). Within the geothermal field, the dacites have been highly altered to kaolinite, quartz, cristobalite, alunite, natroalunite, smectite, native sulphur, jarosite, gypsum and amorphous compounds. Muds from grey to blackish hydrothermal pools additionally contain iron sulphides, mainly pyrite. Despite intense alteration of the original dacites, Zr and Ti have remained essentially immobile, allowing the calculation of mass changes. Major depletions of Fe, Mg, Ca, Na and commonly Si occur over an area of at least 200 x 400 m. The most altered rocks also show losses of Al, light REE and Y, implying leaching by highly acidic waters. A few altered rocks have, however, gained Al together with Si and P. Also present are m-scale zones of silica + native sulphur, wherein the silica appears to represent a residue from the leaching of dacite, rather than a hydrothermal addition. Delta-34S values of samples containing mixtures of sulphates, native sulphur and iron sulphides are all notably negative (-5 to -16 ‰), consistent with derivation of sulphur from acidic magmatic gases that reacted with oxidized groundwater. Despite the strongly acidic alteration of the host rocks, most hydrothermal pools are neutral or only mildly acidic, suggesting that they contain a notable component of meteoric water.

Crude protein and essential amino acid requirements in chicks during the first week posthatch.

PubMed

Sklan, D; Noy, Y

2003-05-01

1. This study examined optimal lysine and sulphur amino acid supply in the first week posthatch in broilers and the relationship between essential amino acids and dietary crude protein during the first week posthatch on performance at 7 d and through marketing. 2. The optimal supply during the 7 d posthatch using a 230 g/kg crude protein diet for sulphur amino acids was 9.1 and for lysine was 10.3-10.8 g/kg with maximal body weight (BW) or feed efficiency as the criteria. 3. Feeding diets with crude protein content ranging from 200 to 260 g/kg with either constant amounts of essential amino acids at different crude protein levels or constant ratios of essential amino acids to crude protein resulted in enhanced performance at 7 but not at 4 d with high protein intake and proportionally increased essential amino acids. 4. Performance on diets with crude protein ranging from 160 to 280 g/kg, with constant ratios of essential amino acid to crude protein, was much enhanced with the high crude protein diets at 7 d. All chicks were transferred to standard diets after 7 d and the BW advantage due to the balanced amino acid-high crude protein diet remained through marketing. 5. Thus increasing essential amino acids in a constant ratio to crude protein enhanced performance during the 7 d posthatch.

Electrothermal vaporization of mineral acid solutions in inductively coupled plasma mass spectrometry: comparison with sample nebulization

NASA Astrophysics Data System (ADS)

Mora, Juan; Gras, Luis; van Veen, Eric H.; de Loos-Vollebregt, Margaretha T. C.

1999-06-01

The analytical behaviour of an electrothermal vaporization (ETV) device for the introduction of mineral acid solutions in inductively coupled plasma mass spectrometry (ICP-MS) was evaluated. Water, nitric acid, hydrochloric acid, perchloric acid and sulphuric acid in concentrations within the 0.05-1.0 mol l-1 range were studied. For all the acids tested, increasing the acid concentration increases the ion signal and deteriorates the precision. The magnitude of the signal enhancement depends on the analyte and on the acid considered. Acid solutions give rise to ion signals that are between 2 and 10 times higher than those with water. Among the acids tested, sulphuric acid provides the highest signals. The addition of palladium reduces matrix effects due to the acids and increases the signal in ETV ICP-MS. In comparison with conventional sample nebulization (CS), the ETV sample introduction system provides higher sensitivities (between 2 and 20 times higher) at the same acid concentration. The magnitude of this improvement is similar to that obtained with a microwave desolvation system (MWDS). The ETV sample introduction system gives rise to the lowest background signals from matrix-induced species. Due to this fact, the limits of detection (LODs) obtained for the isotopes affected by any interference are lower for ETV sample introduction than those obtained with the CS and the MWDS. For the isotopes that do not suffer from matrix-induced spectral interferences, the ETV gives rise to LODs higher than those obtained with the CS. For these isotopes the lowest LODs are obtained with MWDS.

Semi-mechanistic modelling of ammonia absorption in an acid spray wet scrubber based on mass balance

USDA-ARS?s Scientific Manuscript database

A model to describe reactive absorption of ammonia (NH3) in an acid spray scrubber was developed as a function of the combined overall mass transfer coefficient K. An experimental study of NH3 absorption using 1% dilute sulphuric acid was carried out under different operating conditions. An empiric...

The regulation of sulphurated amino acid junctions: fact or fiction in the field of inflammation?

PubMed

Santangelo, F

2002-01-01

The diet of industrialised countries is usually rich in amino acids, which are in part used as a source of calories. However, metabolic alterations are observed in diseased patients and a preferential retention of Sulphurated Amino Acids (SAA) occurs during the inflammatory response. Moreover, it has been demonstrated in a model of an acute sepsis phase of rats that the metabolism of Cysteine is modified. The liver converts Cysteine at a different ratio of Sulphate to Taurine (Tau) i.e. the sulphate production decreases while the Tau conversion increases. The Glutathione (GSH) concentration is greater in the liver, kidneys and other organs and the Cysteine incorporation into proteins is higher in the spleen, lungs and plasma (Acute Phase Proteins) while the Albumin level decreases. The pro-inflammatory cytokines such as Interleukin-1, Interleukin-6 and TNF- alpha are the main initiators that alter protein and amino acid metabolism. Another important phenomenon is the impairment of Methionine conversion to Cysteine during stress. For example, premature infants or AIDS patients are capable of synthesizing Cysteine from Methionine at a much lower rate. Thus, the metabolic flow through the trans-sulphuration path may be inadequate to meet the Cysteine demand under critical conditions. In this complex picture, an SAA supply may contribute to an immune system regulation.

Equilibrium distribution of dissolved sulphur species in water at 25°C and 1 atm total pressure

USGS Publications Warehouse

Garrels, R.M.; Naeser, C.R.

1958-01-01

The Eh-pH diagrams for the equilibrium concentrations in aqueous solution at 25°C of native sulphur and all the various sulphur-containing ions and acids from which the ions are produced have been constructed for systems having a total sulphur concentration of 0.1 molar. The composite of these diagrams indicates that elemental sulphur, H2S, HS− HSO4− and SO4 are the species that predominate in the environments that might be found in nature. This indication is in agreement with the composition of all sulphur-containing minerals.

Bacterial leaching of waste uranium materials.

PubMed

Barbic, F F; Bracilović, D M; Krajincanić, B V; Lucić, J L

1976-01-01

The effect of ferrobacteria and thiobacteria on the leaching of waste uranium materials from which 70-80% of uranium was previously leached by classical chemical hydrometallurgical procedure has been investigated. The bacteria used are found in the ore and the mine water of Zletovska River locality, Yugoslavia. Parameters of biological leaching were examined in the laboratory. Leaching conditions were changed with the aim of increasing the amount of uranium leached. The effect of pyrite added to the waste materials before the beginning of leaching has also been examined. Uranium leaching is directly proportional to the composition and number of ferrobacteria and thiobacteria, and increased by almost twice the value obtained from the same starting materials without using bacteria. Increased sulphuric acid concentrations stimulate considerably the rate of leaching. Uranium leaching is increased up to 20% while sulphuric acid consumption is simultaneously decreased by the addition of pyrite. Uranium concentrations in starting waste materials used for leaching were extremely low (0.0278 and 0.372% U) but about 60% recovery of uranium was obtained, with relatively low consumption of sulphuric acid.

Using heat pipe to make isotherm condition in catalytic converters of sulfuric acid plants

NASA Astrophysics Data System (ADS)

Yousefi, M.; Pahlavanzadeh, H.; Sadrameli, S. M.

2017-08-01

In this study, for the first time, it is tried to construct a pilot reactor, for surveying the possibility of creating isothermal condition in the catalytic convertors where SO2 is converted to SO3 in the sulfuric acid plants by heat pipe. The thermodynamic and thermo-kinetic conditions were considered the same as the sulfuric acid plants converters. Also, influence of SO2 gas flow rate on isothermal condition, has been studied. A thermo-siphon type heat pipe contains the sulfur + 5% iodine as working fluid, was used for disposing the heat of reaction from catalytic bed. Our results show that due to very high energy-efficiency, isothermal and passive heat transfer mechanism of heat pipe, it is possible to reach more than 95% conversion in one isothermal catalytic bed. As the results, heat pipe can be used as a certain piece of equipment to create isothermal condition in catalytic convertors of sulphuric acid plants. With this work a major evaluation in design of sulphuric acid plants can be taken place.

Effects of application of sulphuric acid to poor pine forests

Treesearch

C. O. Tamm; G. Wiklander; B. Popovic

1976-01-01

The department of plant ecology and soils of the College of Forestry has been interested in the problem of the acid rain as an environmental factor since the discussion of this problem started in the late 1960's (0den 1968).

SULPHUR-CONTAINING AMINO ACIDS METABOLISM IN EXPERIMENTAL HYPER- AND HYPOTHYROIDISM IN RATS.

PubMed

Nechiporuk, V; Zaichko, N; Korda, М; Melnyk, A; Koloshko, O

2017-10-01

Hyper- and hypothyroidism are some of the most common endocrinopathies that cause many metabolic disorders including amino acids metabolism. However, a specific molecular mechanism of thyroid hormones influence on sulphur-containing amino acids metabolism has not been established. The aim of our research was to investigate experimentally the influence of thyroid gland functional state on the main enzymatic systems of sulphur-containing amino acids metabolism in liver and kidneys, the content of homocysteine, cysteine and H2S in blood. The rats were administered with L-thyroxine and mercazolil to simulate the states of hyper- and hypothyroidism, which were confirmed by the content of fT3, fT4 and TSH in the blood. In liver and kidneys of the animals with hypothyroidism we observed the decrease in the activity of enzymes of remethylation cycle of S-adenosylmethioninsyntase, S-adenosylhomocysteinhyhdrolase, betaine-homocysteine methyltransferase. Suppression of transsulfuration transformation of homocysteine to cysteine in hypothyroidism was mainly due to the inhibition of cystathionine synthase activity of cystathionine-β-synthase, wherein cystathionase activity of cystathionine-γ-lyase was not changed. In animals with hypothyroidism we also noticed the inhibition of cysteine desulfunation reactions: the activity of enzymes of cystathionine-β-synthase, cystathionine-γ-lyase and cysteine aminotransferase significantly decreased in liver and kidneys. Experimental hyperthyroidism was accompanied by increase in activity of remethylation cycle enzymes, increase in cystationine synthase activity of cystathionine-β-synthase in liver and activity of these enzymes in kidneys. The simulation of hyperthyroidism led to the decrease of homocysteine concentration, and of hypothyroidism - to the increase of homocysteine and cysteine concentrations and reduced H2S content in blood of the animals. Thus, the significant risk factors for the development of atherosclerosis, endothelial dysfunction and hypercoagulation in hypothyroid conditions may be the disorders in the processes of remethylation, transsulfuration, and desulfuration of sulphur-containing amino acids in organs.

Sulphur fertilization influences the sulphur species composition in Allium sativum: sulphomics using HPLC-ICPMS/MS-ESI-MS/MS.

PubMed

Raab, Andrea; Ronzan, Marilena; Feldmann, Joerg

2017-10-18

Garlic (A. sativum) contains a large number of small sulphur (S)-containing metabolites, which are important for its taste and smell and vary with A. sativum variety and growth conditions. This study was designed to investigate the influence of different sulphur-fertilization regimes on low molecular weight S-species by attempting the first sulphur mass balance in A. sativum roots and bulbs using HPLC-ICPMS/MS-ESI-MS/MS. Species unspecific quantification of acid soluble S-containing metabolites was achieved using HPLC-ICP-MS/MS. For identification of the compounds, high resolution ESI-MS (Orbitrap LTQ and q-TOF) was used. The plants contained up to 54 separated sulphur-containing compounds, which constitute about 80% of the total sulphur present in A. sativum. The roots and bulbs of A. sativum contained the same compounds, but not necessarily the same amounts and proportions. The S-containing metabolites in the roots reacted more sensitively to manipulations of sulphur fertilization than those compounds in the bulbs. In addition to known compounds (e.g. γ-glutamyl-S-1-propenylcysteine) we were able to identify and partially quantify 31 compounds. Three as yet undescribed S-containing compounds were also identified and quantified for the first time. Putative structures were assigned to the oxidised forms of S-1-propenylmercaptoglutathione, S-2-propenylmercaptoglutathione, S-allyl/propenyl-containing PC-2 and 2-amino-3-[(2-carboxypropyl)sulfanyl]propanoic acid. The parallel use of ICP-MS/MS as a sulphur-specific detector and ESI-MS as a molecular detector simplifies the identification and quantification of sulphur containing metabolites without species specific standards. This non-target analysis approach enables a mass balance approach and identifies the occurrence of the so far unidentified organosulphur compounds. The experiments showed that the sulphur-fertilization regime does not influence sulphur-speciation, but the concentration of some S-containing compounds in roots is dependent on sulphur fertilization.

Gemini surfactants from natural amino acids.

PubMed

Pérez, Lourdes; Pinazo, Aurora; Pons, Ramon; Infante, Mrosa

2014-03-01

In this review, we report the most important contributions in the structure, synthesis, physicochemical (surface adsorption, aggregation and phase behaviour) and biological properties (toxicity, antimicrobial activity and biodegradation) of Gemini natural amino acid-based surfactants, and some potential applications, with an emphasis on the use of these surfactants as non-viral delivery system agents. Gemini surfactants derived from basic (Arg, Lys), neutral (Ser, Ala, Sar), acid (Asp) and sulphur containing amino acids (Cys) as polar head groups, and Geminis with amino acids/peptides in the spacer chain are reviewed. © 2013.

Molecular understanding of sulphuric acid-amine particle nucleation in the atmosphere.

PubMed

Almeida, João; Schobesberger, Siegfried; Kürten, Andreas; Ortega, Ismael K; Kupiainen-Määttä, Oona; Praplan, Arnaud P; Adamov, Alexey; Amorim, Antonio; Bianchi, Federico; Breitenlechner, Martin; David, André; Dommen, Josef; Donahue, Neil M; Downard, Andrew; Dunne, Eimear; Duplissy, Jonathan; Ehrhart, Sebastian; Flagan, Richard C; Franchin, Alessandro; Guida, Roberto; Hakala, Jani; Hansel, Armin; Heinritzi, Martin; Henschel, Henning; Jokinen, Tuija; Junninen, Heikki; Kajos, Maija; Kangasluoma, Juha; Keskinen, Helmi; Kupc, Agnieszka; Kurtén, Theo; Kvashin, Alexander N; Laaksonen, Ari; Lehtipalo, Katrianne; Leiminger, Markus; Leppä, Johannes; Loukonen, Ville; Makhmutov, Vladimir; Mathot, Serge; McGrath, Matthew J; Nieminen, Tuomo; Olenius, Tinja; Onnela, Antti; Petäjä, Tuukka; Riccobono, Francesco; Riipinen, Ilona; Rissanen, Matti; Rondo, Linda; Ruuskanen, Taina; Santos, Filipe D; Sarnela, Nina; Schallhart, Simon; Schnitzhofer, Ralf; Seinfeld, John H; Simon, Mario; Sipilä, Mikko; Stozhkov, Yuri; Stratmann, Frank; Tomé, Antonio; Tröstl, Jasmin; Tsagkogeorgas, Georgios; Vaattovaara, Petri; Viisanen, Yrjo; Virtanen, Annele; Vrtala, Aron; Wagner, Paul E; Weingartner, Ernest; Wex, Heike; Williamson, Christina; Wimmer, Daniela; Ye, Penglin; Yli-Juuti, Taina; Carslaw, Kenneth S; Kulmala, Markku; Curtius, Joachim; Baltensperger, Urs; Worsnop, Douglas R; Vehkamäki, Hanna; Kirkby, Jasper

2013-10-17

Nucleation of aerosol particles from trace atmospheric vapours is thought to provide up to half of global cloud condensation nuclei. Aerosols can cause a net cooling of climate by scattering sunlight and by leading to smaller but more numerous cloud droplets, which makes clouds brighter and extends their lifetimes. Atmospheric aerosols derived from human activities are thought to have compensated for a large fraction of the warming caused by greenhouse gases. However, despite its importance for climate, atmospheric nucleation is poorly understood. Recently, it has been shown that sulphuric acid and ammonia cannot explain particle formation rates observed in the lower atmosphere. It is thought that amines may enhance nucleation, but until now there has been no direct evidence for amine ternary nucleation under atmospheric conditions. Here we use the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber at CERN and find that dimethylamine above three parts per trillion by volume can enhance particle formation rates more than 1,000-fold compared with ammonia, sufficient to account for the particle formation rates observed in the atmosphere. Molecular analysis of the clusters reveals that the faster nucleation is explained by a base-stabilization mechanism involving acid-amine pairs, which strongly decrease evaporation. The ion-induced contribution is generally small, reflecting the high stability of sulphuric acid-dimethylamine clusters and indicating that galactic cosmic rays exert only a small influence on their formation, except at low overall formation rates. Our experimental measurements are well reproduced by a dynamical model based on quantum chemical calculations of binding energies of molecular clusters, without any fitted parameters. These results show that, in regions of the atmosphere near amine sources, both amines and sulphur dioxide should be considered when assessing the impact of anthropogenic activities on particle formation.

Optimization of digestion parameters for analysing the total sulphur of mine tailings by inductively coupled plasma optical emission spectrometry.

PubMed

Alam, Raquibul; Shang, Julie Q; Cheng, Xiangrong

2012-05-01

The oxidation of sulphidic mine tailings and consequent acid generation poses challenges for the environment. Accurate and precise analysis of sulphur content is necessary for impact assessment and management of mine tailings. Here, the authors aim at developing a rapid and easy digestion procedure, which may analyse and measure the total amount of sulphur in mine tailings by using inductively coupled plasma. For evaluating effects of several variables, the researchers used a univariate (analysis of variance (ANOVA)) strategy and considered factors such as composition of the acid mixture, heating time, and refluxing device to optimize the performance. To do the experiment, the researchers have used two certified reference materials (KZK-1 and RTS-2) and samples of tailings from Musselwhite mine. ANOVA result shows that heating time is the most influencing factor on acid digestion of the reference materials whereas in case of a digestion of tailings sample, hydrochloric acid proved to be the most significant parameter. Satisfactory results between the measured and referenced values are found for all experiments. It is found that the aqua regia (1 ml HNO(3) + 3 ml HCl) digestion of 0.1 g of samples after only 40 min of heating at 95°C produced fast, safe, and accurate analytical results with a recovery of 97% for the selected reference materials.

The effect of sulphur dioxide and oxygen on the viability and culturability of a strain of Acetobacter pasteurianus and a strain of Brettanomyces bruxellensis isolated from wine.

PubMed

du Toit, W J; Pretorius, I S; Lonvaud-Funel, A

2005-01-01

The objective of this study was to investigate the effects of free molecular and bound forms of sulphur dioxide and oxygen on the viability and culturability of a selected strain of Acetobacter pasteurianus and a selected strain of Brettanomyces bruxellensis in wine. Acetic acid bacteria and Brettanomyces/Dekkera yeasts associated with wine spoilage were isolated from bottled commercial red wines. One bacterium, A. pasteurianus strain A8, and one yeast, B. bruxellensis strain B3a, were selected for further study. The resistance to sulphur dioxide and the effect of oxygen addition on these two selected strains were determined by using plating and epifluorescence techniques for monitoring cell viability in wine. Acetobacter pasteurianus A8 was more resistant to sulphur dioxide than B. bruxellensis B3a, with the latter being rapidly affected by a short exposure time to free molecular form of sulphur dioxide. As expected, neither of these microbial strains was affected by the bound form of sulphur dioxide. The addition of oxygen negated the difference observed between plate and epifluorescence counts for A. pasteurianus A8 during storage, while it stimulated growth of B. bruxellensis B3a. Acetobacter pasteurianus A8 can survive under anaerobic conditions in wine in the presence of sulphur dioxide. Brettanomyces bruxellensis B3a is more sensitive to sulphur dioxide than A. pasteurianus A8, but can grow in the presence of oxygen. Care should be taken to exclude oxygen from contact with wine when it is being transferred or moved. Wine spoilage can be avoided by preventing growth of undesirable acetic acid bacteria and Brettanomyces/Dekkera yeasts through the effective use of sulphur dioxide and the management of oxygen throughout the winemaking process.

Electrochemical investigation of lead-calcium alloys in sulphuric acid

NASA Astrophysics Data System (ADS)

Bass, K.; Ellis, S. R.; Johnson, M.; Hampson, N. A.

The hydrogen evolution reaction from, and the cycle life (Pb /ar PbSO 4) of, a series of lead-calcium alloys (0 - 0.2 wt.% Ca) in sulphuric acid hav The exchange current density and Tafel slope for the H.R.E. increase with Ca content up to 0.05 wt.% then decrease to a value approaching that of pure The observed results are explained by: (i) preferential adsorption of calcium ions at the electrode surface; (ii) incorporation of Ca, to form a supersaturated solution, with alloys containing < 0.075 wt.% Ca; (iii) formation of an insoluble, non-conducting layer of calcium sulphate on the high content alloy.

Methionine catabolism and production of volatile sulphur compounds by OEnococcus oeni.

PubMed

Pripis-Nicolau, L; de Revel, G; Bertrand, A; Lonvaud-Funel, A

2004-01-01

During malolactic fermentation (MLF), the secondary metabolisms of lactic acid bacteria (LAB) contribute to the organoleptic modification of wine. To understand the contribution of MLF, we evaluated the capacity of various wine LAB to metabolize methionine. Using gas chromatography (GC) coupled either with mass spectrometry (MS) or a flame photometry detector in sulphur mode (FPD), we studied this metabolism in laboratory media and wine. In laboratory media, several LAB isolated from wine were able to metabolize methionine. They formed methanethiol, dimethyl disulphide, 3-(methylsulphanyl)propan-1-ol and 3-(methylsulphanyl)propionic acid. These are known to have powerful characteristic odours and play a role in the aromatic complexity of wine. In various red wines, after MLF only the 3-(methylsulphanyl)propionic acid concentration increased significantly, as verified with several commercial starter cultures. This compound, which is characterized by chocolate and roasted odours, could contribute to the aromatic complexity produced by MLF. This study shows that LAB isolated from wine, especially OEnococcus oeni strains, the major species in MLF, are able to metabolize methionine to form volatile sulphur compounds. This is the first study to demonstrate the capacity of wine LAB to metabolize methionine.

GEOCHEMICAL FEATURES OF WATER-ROCK INTERACTIONS AT THE SULPHUR BANK MERCURY MINE, LAKE COUNTY, CALIFORNIA

EPA Science Inventory

The Sulphur Bank Mercury Mine on the eastern shore of Clear Lake is the source of poor quality acid mine drainage seeping into Clear Lake. Lateral and vertical geochemical trends in ground water composition point to a number of redox reactions taking place as a function of subsu...

Dye adsorption onto activated carbons from tyre rubber waste using surface coverage analysis.

PubMed

Mui, Edward L K; Cheung, W H; Valix, Marjorie; McKay, Gordon

2010-07-15

Two types of activated carbons from tyre char (with or without sulphuric acid treatment) were produced via carbon dioxide activation with BET surface areas in the range 59-1118 m(2)/g. Other characterisation tests include micropore and mesopore surface areas and volumes, pH, and elemental compositions, particularly heteroatoms such as nitrogen and sulphur. They were correlated to the adsorption capacity which were in the range of 0.45-0.71 mmol/g (untreated) and 0.62-0.84 mmol/g (acid-treated) for Acid Blue 25. In the case of larger-sized molecules like Acid Yellow 117, capacities were in the range of 0.23-0.42 mmol/g (untreated) and 0.29-0.40 mmol/g (acid-treated). Some tyre carbons exhibit a more superior performance than a microporous, commercial activated carbon (Calgon F400). By modelling the dye adsorption equilibrium data, the Redlich-Peterson isotherm is adopted as it has the lowest SSE. Based on the surface coverage analysis, a novel molecular orientation modelling of adsorbed dyes has been proposed and correlated with surface area and surface charge. For the acid dyes used in this study, molecules were likely to be adsorbed by the mesopore areas. Copyright 2010 Elsevier Inc. All rights reserved.

Responses to betaine and inorganic sulphur of sheep in growth performance and fibre growth.

PubMed

Nezamidoust, M; Alikhani, M; Ghorbani, G R; Edriss, M A

2014-12-01

Sulphur-containing amino acids (SAA) are essential and usually the first limiting amino acids for growth, milk and wool production. The keratin fibre that grows from epidermal tissue is rich in SAA. The rate of fibre growth and its S content are influenced by the availability of SAA. Betaine is a dietary source for a labile methyl group and actively participates in methionine metabolism by donating methyl groups for the remethylation of homocysteine to methionine. Ruminants are capable of synthesizing SAA from inorganic S sources, and most bacteria in the rumen can use inorganic S to meet their requirements for growth. The objective of this study was to examine whether betaine and an inorganic sulphur supplement could provide methyl groups and sulphur amino acids in a way that growth performance and wool production of ewes and lambs are improved. Treatments performed included betaine supplementation, sulphate supplementation and betaine plus sulphate supplementation with five replications for each treatment. The dry matter intake of the ewes was affected by betaine plus sulphate supplementation (p < 0.05). In the ewes, betaine plus sulphate supplementation increased (p < 0.05) the wool growth rate, wool yield, staple length and wool sulphur concentration, while decreasing wool wax and wool yellowness (p < 0.05). In the lambs, wool growth rate, wool yield, fibre diameter, staple length, staple strength, wool sulphur concentration, wool wax and fibre percentage did not differ (p > 0.05) between treatments. In the ewes, plasma methionine concentration increased (p < 0.05) with betaine plus sulphate treatment. No corresponding difference (p > 0.05) was observed in plasma methionine concentration in the lambs. It can be concluded that betaine plus sulphate supplementation has the potential to change wool characteristics in the ewes, while these compounds were without any effect on growth and wool production of the lambs. Combining the two supplements was advantageous. Journal of Animal Physiology and Animal Nutrition © 2014 Blackwell Verlag GmbH.

Membrane extraction with thermodynamically unstable diphosphonic acid derivatives

DOEpatents

Horwitz, Earl Philip; Gatrone, Ralph Carl; Nash, Kenneth LaVerne

1997-01-01

Thermodynamically-unstable complexing agents which are diphosphonic acids and diphosphonic acid derivatives (or sulphur containing analogs), like carboxyhydroxymethanediphosphonic acid and vinylidene-1,1-diphosphonic acid, are capable of complexing with metal ions, and especially metal ions in the II, III, IV, V and VI oxidation states, to form stable, water-soluble metal ion complexes in moderately alkaline to highly-acidic media. However, the complexing agents can be decomposed, under mild conditions, into non-organic compounds which, for many purposes are environmentally-nondamaging compounds thereby degrading the complex and releasing the metal ion for disposal or recovery. Uses for such complexing agents as well as methods for their manufacture are also described.

Development of a Chemical Process for Production of Cesium Chloride from a Canadian Pollucite Ore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parsons, H. W.; Vezina, J. A.; Simard, R.

1963-01-01

A chemical process was developed for the production of a high-purity cesium chioride from a pollucite (cesium aluminum silicate) ore from the Manitoba deposit of Chemalloy Minerais Ltd. The history of the deposit, and the present and possible future uses of cesium are briefly reviewed. Laboratory and piiot plant investigations on this ore have shown that a cyclic sulphuric acid leach followed by fractional crystallization will produce a rubidiumfree cesium alum, which can be converted to cesium chloride by thermal decomposition and ion exchange. On the basis of these findings it is concluded that the process is applicable to themore » tonnage production of cesium chloride. Reagent consumption was found to be 3.3 sulphuric acid and 0.3 lb hydrochloric acid per pound of cesium extracted. Overall extraction of cesium was 95 to 96%. (auth)« less

Environmental policy constraints for acidic exhaust gas scrubber discharges from ships.

PubMed

Ülpre, H; Eames, I

2014-11-15

Increasingly stringent environmental legislation on sulphur oxide emissions from the combustion of fossil fuels onboard ships (International Maritime Organization (IMO) Regulation 14) can be met by either refining the fuel to reduce sulphur content or by scrubbing the exhaust gases. Commonly used open loop marine scrubbers discharge warm acidic exhaust gas wash water into the sea, depressing its pH. The focus on this paper is on the physics and chemistry behind the disposal of acidic discharges in seawater. The IMO Marine Environment Protection Committee (MEPC 59/24/Add.1 Annex 9) requires the wash water to reach a pH greater than 6.5 at a distance of 4m from the point of discharge. We examine the engineering constraints, specifically size and number of ports, to identify the challenges of meeting regulatory compliance. Copyright © 2014. Published by Elsevier Ltd.

Acidic leaching both of zinc and iron from basic oxygen furnace sludge.

PubMed

Trung, Zuzana Hoang; Kukurugya, Frantisek; Takacova, Zita; Orac, Dusan; Laubertova, Martina; Miskufova, Andrea; Havlik, Tomas

2011-09-15

During the steel production in the basic oxygen furnace (BOF), approximately 7-15 kg of dust per tonne of produced steel is generated. This dust contains approximately 1.4-3.2% Zn and 54-70% Fe. Regarding the zinc content, the BOF dust is considered to be highly problematic, and therefore new technological processes for recycling dusts and sludge from metallurgical production are still searched for. In this study the hydrometallurgical processing of BOF sludge in the sulphuric acid solutions under atmospheric pressure and temperatures up to 100 °C is investigated on laboratory scale. The influence of sulphuric acid concentration, temperature, time and liquid to solid ratio (L:S) on the leaching process was studied. The main aim of this study was to determine optimal conditions when the maximum amount of zinc passes into the solution whilst iron remains in a solid residue. Copyright © 2011 Elsevier B.V. All rights reserved.

The properties of syringyl, guaiacyl and p-hydroxyphenyl artificial lignins

PubMed Central

Bland, D. E.; Logan, A. F.

1965-01-01

1. Artificial lignins have been produced on potato parenchyma. 2. The methoxyl-free lignin and 4-hydroxy-3-methoxy (guaiacyl) lignins could be estimated by the sulphuric acid method but the 4-hydroxy-3,5-dimethoxy (syringyl) lignins could not. 3. Permanganate oxidation of isolated p-coumaric lignin gave 4-hydroxybenzoic acid, 4-hydroxyisophthalic acid and small amounts of hydroxytrimesic acid and 4-hydroxyphthalic acid. Ferulic lignin gave vanillic acid and 5-carboxyvanillic acid and also small amounts of 4-hydroxybenzoic acid and dehydrodivanillic acid. The sinapic lignin gave traces of syringic acid and of 4-hydroxybenzoic acid. 4. The p-coumaric lignin is a highly condensed polymer. The ferulic lignin is partly uncondensed and partly condensed through the 5-position like gymnosperm lignin. The sinapic lignin shows no evidence of condensation and is probably an ether-linked polymer. PMID:14340102

Optimization of the 3-Point Bending Failure of Anodized Aluminum Formed in Tartaric/Sulphuric Acid Using Doehlert Design

NASA Astrophysics Data System (ADS)

Bensalah, W.; Feki, M.; De-Petris Wery, M.; Ayedi, H. F.

2015-02-01

The bending failure of anodized aluminum in tartaric/sulphuric acid bath was modeled using Doehlert design. Bath temperature, anodic current density, sulphuric acid, and tartaric acid concentrations were retained as variables. Thickness measurements and 3-point bending experiments were conducted. The deflection at failure ( D f) and the maximum load ( F m) of each sample were, then, deducted from the corresponding flexural responses. The treatment of experimental results has established mathematical models of second degree reflecting the relation of cause and effect between the factors and the studied properties. The optimum path study of thickness, deflection at failure, and maximum load, showed that the three optima were opposite. Multicriteria optimization using the desirability function was achieved in order to maximize simultaneously the three responses. The optimum conditions were: C tar = 18.2 g L-1, T = 17.3 °C, J = 2.37 A dm-2, C sul = 191 g L-1, while the estimated response values were e = 57.7 µm, D f = 5.6 mm, and F m = 835 N. Using the established models, a mathematical correlation was found between deflection at failure and thickness of the anodic oxide layer. Before bending tests, aluminum oxide layer was examined by scanning electron microscopy (SEM) and atomic force microscopy. After tests, the morphology and the composition of the anodic oxide layer were inspected by SEM, optical microscopy, and glow-discharge optical emission spectroscopy.

Measurement of acid precipitation in Norway

Treesearch

Arne Semb

1976-01-01

Since January 1972, chemical analysis of daily precipitation samples from about 20 background stations in Norway has been carried out on a routine basis. Air monitoring is carried out at six stations. The chemical analysis programme is: sulphate, pH and acidity in precipitation, sulphates and sulphur dioxide in air. In addition, more detailed chemical analysis of...

Acidity of open and intercepted precipitation in forests

Treesearch

J. Baker; Drake Hocking; Marvin Nyborg

1976-01-01

Emissions of sulphur dioxide appear to have an acidifying effect on grossfall (open rainfall), throughfall, stemflow and soil solution at sites near major sources. Resulting effects on soil chemistry include elevated extractable acidity and aluminum and depressed exchangeable bases, especially calcium and magnesium. These changes are mostly in the incipient phases in...

Separation of thorium (IV) from lanthanide concentrate (LC) and water leach purification (WLP) residue

DOE Office of Scientific and Technical Information (OSTI.GOV)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

Thorium (IV) content in industrial residue produced from rare earth elements production industry is one of the challenges to Malaysian environment. Separation of thorium from the lanthanide concentrate (LC) and Water Leach Purification (WLP) residue from rare earth elements production plant is described. Both materials have been tested by sulphuric acid and alkaline digestions. Th concentrations in LC and WLP were determined to be 1289.7 ± 129 and 1952.9±17.6 ppm respectively. The results of separation show that the recovery of Th separation from rare earth in LC after concentrated sulphuric acid dissolution and reduction of acidity to precipitate Th wasmore » found 1.76-1.20% whereas Th recovery from WLP was less than 4% after concentrated acids and alkali digestion processes. Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) was used to determine Th concentrations in aqueous phase during separation stages. This study indicated that thorium maybe exists in refractory and insoluble form which is difficult to separate by these processes and stays in WLP residue as naturally occurring radioactive material (NORM)« less

Extraction and derivatization of polar herbicides for GC-MS analyses.

PubMed

Ranz, Andreas; Maier, Eveline; Motter, Herbert; Lankmayr, Ernst

2008-09-01

A sample preparation procedure including a simultaneous microwave-assisted (MA) extraction and derivatization for the determination of chlorophenoxy acids in soil samples is presented. For a selective and sensitive measurement, an analytical technique such as GC coupled with MS needs to be adopted. For GC analyses, chlorophenoxy acids have to be converted into more volatile and thermally stable derivatives. Derivatization by means of microwave radiation offers new alternatives in terms of shorter derivatization time and reduces susceptibility for the formation of artefacts. Extraction and derivatization into methyl esters (ME) were performed with sulphuric acid and methanol. Due to the novelty of the simultaneous extraction and derivatization assisted by means of microwave radiation, a careful investigation and optimization of influential reaction parameters was necessary. It could be shown that the combination of sulphuric acid and methanol provides a fast sample preparation including an efficient clean up procedure. The data obtained by the described method are in good agreement with those published for the reference material. Finally, compared to conventional heating and also to the standard procedure of the EPA, the sample preparation time could be considerably shortened.

Membrane extraction with thermodynamically unstable diphosphonic acid derivatives

DOEpatents

Horwitz, E.P.; Gatrone, R.C.; Nash, K.L.

1997-10-14

Thermodynamically-unstable complexing agents which are diphosphonic acids and diphosphonic acid derivatives (or sulphur containing analogs), like carboxyhydroxymethanediphosphonic acid and vinylidene-1,1-diphosphonic acid, are capable of complexing with metal ions, and especially metal ions in the II, III, IV, V and VI oxidation states, to form stable, water-soluble metal ion complexes in moderately alkaline to highly-acidic media. However, the complexing agents can be decomposed, under mild conditions, into non-organic compounds which, for many purposes are environmentally-nondamaging compounds thereby degrading the complex and releasing the metal ion for disposal or recovery. Uses for such complexing agents as well as methods for their manufacture are also described. 1 fig.

Extracting metal ions with diphosphonic acid, or derivative thereof

DOEpatents

Horwitz, Earl P.; Gatrone, Ralph C.; Nash, Kenneth L.

1994-01-01

Thermodynamically-unstable complexing agents which are diphosphonic acids and diphosphonic acid derivatives (or sulphur containing analogs), like carboxyhydroxymethanediphosphonic acid and vinylidene-1,1-diphosphonic acid, are capable of complexing with metal ions, and especially metal ions in the II, III, IV, V and VI oxidation states, to form stable, water-soluble metal ion complexes in moderately alkaline to highly-acidic media. However, the complexing agents can be decomposed, under mild conditions, into non-organic compounds which, for many purposes are environmentally-nondamaging compounds thereby degrading the complex and releasing the metal ion for disposal or recovery. Uses for such complexing agents as well as methods for their manufacture are also described.

Remediation of grey forest soils heavily polluted with heavy metals by means of their leaching at acidic pH followed by the soil reclamation by means of neutralization and bacterial manure addition

NASA Astrophysics Data System (ADS)

Georgiev, Plamen; Groudev, Stoyan; Spasova, Irena; Nicolova, Marina

2014-05-01

Some grey forest soils in Western Bulgaria are heavily polluted with heavy metals (copper, lead, and zinc), arsenic, and uranium due to the infiltration of acid mine drainage generated at the abandoned uranium mine Curilo. This paper presents some results from a study about soil remediation based on the contaminants leaching from the topsoil by means of irrigation with solutions containing sulphuric acid or its in situ generation by means of sulphur-oxidizing chemolithotrophic bacteria in or without the presence of finely cut straw. These methods were tested in large scale zero suction lysimeters. The approaches based on S° and finely cut straw addition was the most efficient amongst the tested methods and for seven months of soil remediation the concentration of all soil contaminants were decreased below the relevant Maximum Admissible Concentration (MAC). Neutralization of the soil acidity was applied as a next stage of soil reclamation by adding CaCO3 and cow manure. As a result, soil pH increased from strongly acidic (2.36) to slightly acidic (6.15) which allowed subsequent addition of humic acids and bacterial manure to the topsoil. The soil habitat changed in this way facilitated the growth of microorganisms which restored the biogeochemical cycles of nitrogen and carbon to the levels typical for non-polluted grey forest soil.

Canadian experiences in development of critical loads for sulphur and nitrogen

Treesearch

Shaun Watmough; Julian Aherne; Paul Arp; Ian DeMerchant; Rock Ouimet

2006-01-01

Critical loads are a broad-scale modelling approach designed to assess the potential risk of pollutants to ecosystems. A description of the methodology for estimating critical loads (sulphur and nitrogen) for acid deposition (CL(A)) for upland forests in eastern Canada is presented, using a case study in central Ontario. In eastern Canada, CL(A) have been calculated...

The NADH:flavin oxidoreductase Nox from Rhodococcus erythropolis MI2 is the key enzyme of 4,4'-dithiodibutyric acid degradation.

PubMed

Khairy, H; Wübbeler, J H; Steinbüchel, A

2016-12-01

The reduction of the disulphide bond is the initial catabolic step of the microbial degradation of the organic disulphide 4,4'-dithiodibutyric acid (DTDB). Previously, an NADH:flavin oxidoreductase from Rhodococcus erythropolis MI2 designated as Nox MI2 , which belongs to the old yellow enzyme (OYE) family, was identified. In the present study, it was proven that Nox MI2 has the ability to cleave the sulphur-sulphur bond in DTDB. In silico analysis revealed high sequence similarities to proteins of the flavin mononucleotide (FMN) reductase family identified in many strains of R. erythropolis. Therefore, nox was heterologously expressed in the pET23a(+) expression system using Escherichia coli strain BL21(DE3) pLysS, which effectively produces soluble active Nox MI2 . Nox MI2 showed a maximum specific activity (V max ) of 3·36 μmol min -1  mg -1 corresponding to a k cat of 2·5 s -1 and an apparent substrate K m of 0·6 mmol l -1 , when different DTDB concentrations were applied. No metal cofactors were required. Moreover, Nox MI2 had very low activity with other sulphur-containing compounds like 3,3'-dithiodipropionic acid (8·0%), 3,3'-thiodipropionic acid (7·6%) and 5,5'-dithiobis(2-nitrobenzoic acid) (8·0%). The UV/VIS spectrum of Nox MI2 revealed the presence of the cofactor FMN. Based on results obtained, Nox MI2 adds a new physiological substrate and mode of action to OYE members. It was unequivocally demonstrated in this study that an NADH:flavin oxidoreductase from Rhodococcus erythropolis MI2 (Nox MI2 ) is able to cleave the xenobiotic disulphide 4,4'-dithiodibutyric acid (DTDB) into two molecules of 4-mercaptobutyric acid (4MB) with concomitant consumption of NADH. Nox MI2 showed a high substrate specificity as well as high heat stability. This study provides the first detailed characterization of the initial cleavage of DTDB, which is considered as a promising polythioester precursor. © 2016 The Society for Applied Microbiology.

Microbial oxidation of pyrrhotites in coal chars

USGS Publications Warehouse

Miller, K.W.; Risatti, J.B.

1988-01-01

The ability of Thiobacillus ferrooxidans to oxidize pyrrhotite minerals occurring in coal chars was investigated, to evaluate the feasibility of microbial char desulphurization. Bio-oxidation of pyrrhotites in chars produced by two different processes was demonstrated conclusively. Microbial removal of sulphur from a char and its parent coal proceeded at the rate of 3.5% and 12% day-1, respectively with a total of 48% and 81% removal after 27 days. The pH of shake flask cultures containing the coal dropped naturally to a final value of 2.2, while the pH of cultures containing the corresponding char rose and had to be lowered artificially with additional acid. Amending char cultures with elemental sulphur to increase acidity upon bio-oxidation and prevent precipitation of ferric iron was successful; however, the extent of pyrrhotite removal, as demonstated by X-ray diffraction analysis, was not improved. As yet, there is no explanation for the failure of microbial removal of pyrrhotitic sulphur to go to completion. ?? 1988.

The effects of added sulphur amino acids, threonine and an ideal amino acid ratio on nitrogen metabolism in mature, overweight dogs.

PubMed

Bohaty, Robin E; de Godoy, Maria R C; McLeod, Kyle R; Harmon, David L

2012-02-01

The objectives of this study were to investigate the effects of added essential amino acids in conjunction with a dietary lysine/MJ of 0.72 on nitrogen (N) metabolism in dogs. Treatments were; a control diet, a diet that provided an ideal amino acid profile (IAA), a diet with added total sulphur amino acids (TSAA), and a diet with added TSAA and threonine (TT). Diets were fed to eight overweight, mature, female hounds using a replicated 4 x 4 Latin Square design. Food intake was similar across treatments, however, food N intake was higher (p < 0.001) for TSAA than control, IAA or TT. Nitrogen absorbed was higher (p < 0.01) for TSAA than IAA and control. Urea N excretion was greater for control than TT (p < 0.05). Urine N excretion did not differ between diets. There were no differences in digestibility or N retention of diets. There were no differences in protein turnover, synthesis, or degradation. Blood metabolites were within normal ranges and did not differ due to dietary treatment. Based on the measurements made in this study, there is no benefit for added TSAA, TT or additional EAA in diets for mature dogs formulated to provide a 0.72 g lysine/MJ ME ratio.

Selective environmental stress from sulphur emitted by continental flood basalt eruptions

NASA Astrophysics Data System (ADS)

Schmidt, Anja; Skeffington, Richard; Thordarson, Thorvaldur; Self, Stephen; Forster, Piers; Rap, Alexandru; Ridgwell, Andy; Fowler, David; Wilson, Marjorie; Mann, Graham; Wignall, Paul; Carslaw, Ken

2016-04-01

Several biotic crises during the past 300 million years have been linked to episodes of continental flood basalt volcanism, and in particular to the release of massive quantities of magmatic sulphur gas species. Flood basalt provinces were typically formed by numerous individual eruptions, each lasting years to decades. However, the environmental impact of these eruptions may have been limited by the occurrence of quiescent periods that lasted hundreds to thousands of years. Here we use a global aerosol model to quantify the sulphur-induced environmental effects of individual, decade-long flood basalt eruptions representative of the Columbia River Basalt Group, 16.5-14.5 million years ago, and the Deccan Traps, 65 million years ago. For a decade-long eruption of Deccan scale, we calculate a decadal-mean reduction in global surface temperature of 4.5 K, which would recover within 50 years after an eruption ceased unless climate feedbacks were very different in deep-time climates. Acid mists and fogs could have caused immediate damage to vegetation in some regions, but acid-sensitive land and marine ecosystems were well-buffered against volcanic sulphur deposition effects even during century-long eruptions. We conclude that magmatic sulphur from flood basalt eruptions would have caused a biotic crisis only if eruption frequencies and lava discharge rates had been high and sustained for several centuries at a time.

Selective environmental stress from sulphur emitted by continental flood basalt eruptions

NASA Astrophysics Data System (ADS)

Schmidt, Anja; Skeffington, Richard A.; Thordarson, Thorvaldur; Self, Stephen; Forster, Piers M.; Rap, Alexandru; Ridgwell, Andy; Fowler, David; Wilson, Marjorie; Mann, Graham W.; Wignall, Paul B.; Carslaw, Kenneth S.

2016-01-01

Several biotic crises during the past 300 million years have been linked to episodes of continental flood basalt volcanism, and in particular to the release of massive quantities of magmatic sulphur gas species. Flood basalt provinces were typically formed by numerous individual eruptions, each lasting years to decades. However, the environmental impact of these eruptions may have been limited by the occurrence of quiescent periods that lasted hundreds to thousands of years. Here we use a global aerosol model to quantify the sulphur-induced environmental effects of individual, decade-long flood basalt eruptions representative of the Columbia River Basalt Group, 16.5-14.5 million years ago, and the Deccan Traps, 65 million years ago. For a decade-long eruption of Deccan scale, we calculate a decadal-mean reduction in global surface temperature of 4.5 K, which would recover within 50 years after an eruption ceased unless climate feedbacks were very different in deep-time climates. Acid mists and fogs could have caused immediate damage to vegetation in some regions, but acid-sensitive land and marine ecosystems were well-buffered against volcanic sulphur deposition effects even during century-long eruptions. We conclude that magmatic sulphur from flood basalt eruptions would have caused a biotic crisis only if eruption frequencies and lava discharge rates had been high and sustained for several centuries at a time.

Chemiluminescence determination of ferulic acid by flow-injection analysis using cerium(IV) sensitized by rhodamine 6G.

PubMed

Wang, Ju Peng; Li, Nian Bing; Luo, Hong Qun

2008-11-01

A simple, sensitive and rapid flow-injection chemiluminescence method has been developed for the determination of ferulic acid based on the chemiluminescence reaction of ferulic acid with rhodamine 6G and ceric sulfate in sulphuric acid medium. Strong chemiluminescence signal was observed when ferulic acid was injected into the acidic ceric sulfate solution in a flow-cell. The present method allowed the determination of ferulic acid in the concentration range of 8.0 x 10(-6) to 1.0 x 10(-4) mol l(-1) and the detection limit for ferulic acid was 8.7 x 10(-9) mol l(-1). The relative standard deviation was 2.4% for 10 replicate analyses of 1.0 x 10(-5) mol l(-1) ferulic acid. The proposed method was applied to the determination of ferulic acid in Taita Beauty Essence samples with satisfactory results.

Chemiluminescence determination of ferulic acid by flow-injection analysis using cerium(IV) sensitized by rhodamine 6G

NASA Astrophysics Data System (ADS)

Wang, Ju Peng; Li, Nian Bing; Luo, Hong Qun

2008-11-01

A simple, sensitive and rapid flow-injection chemiluminescence method has been developed for the determination of ferulic acid based on the chemiluminescence reaction of ferulic acid with rhodamine 6G and ceric sulfate in sulphuric acid medium. Strong chemiluminescence signal was observed when ferulic acid was injected into the acidic ceric sulfate solution in a flow-cell. The present method allowed the determination of ferulic acid in the concentration range of 8.0 × 10 -6 to 1.0 × 10 -4 mol l -1 and the detection limit for ferulic acid was 8.7 × 10 -9 mol l -1. The relative standard deviation was 2.4% for 10 replicate analyses of 1.0 × 10 -5 mol l -1 ferulic acid. The proposed method was applied to the determination of ferulic acid in Taita Beauty Essence samples with satisfactory results.

Laser Window Materials and Optical Coating Science

DTIC Science & Technology

1977-08-01

nitric, sulphuric, and acetic acids , but attack was too slow or insufficient. Finally, a mixture of nitric and hydrochloric acids was found to...trace of acetic acid . The As2S3 was subsequently mmm ’■ ’■ I .’■ " "■’ ’ reacted with CS-, tor two hours to remove the impurities and...immersing the deforming boule under Cereclor 42P, a chlorinated paraffin. This viscous, honey-colored liquid is 41%, chlorine by weight, and loses

A pursuit of lineage-specific and niche-specific proteome features in the world of archaea

PubMed Central

2012-01-01

Background Archaea evoke interest among researchers for two enigmatic characteristics –a combination of bacterial and eukaryotic components in their molecular architectures and an enormous diversity in their life-style and metabolic capabilities. Despite considerable research efforts, lineage- specific/niche-specific molecular features of the whole archaeal world are yet to be fully unveiled. The study offers the first large-scale in silico proteome analysis of all archaeal species of known genome sequences with a special emphasis on methanogenic and sulphur-metabolising archaea. Results Overall amino acid usage in archaea is dominated by GC-bias. But the environmental factors like oxygen requirement or thermal adaptation seem to play important roles in selection of residues with no GC-bias at the codon level. All methanogens, irrespective of their thermal/salt adaptation, show higher usage of Cys and have relatively acidic proteomes, while the proteomes of sulphur-metabolisers have higher aromaticity and more positive charges. Despite of exhibiting thermophilic life-style, korarchaeota possesses an acidic proteome. Among the distinct trends prevailing in COGs (Cluster of Orthologous Groups of proteins) distribution profiles, crenarchaeal organisms display higher intra-order variations in COGs repertoire, especially in the metabolic ones, as compared to euryarchaea. All methanogens are characterised by a presence of 22 exclusive COGs. Conclusions Divergences in amino acid usage, aromaticity/charge profiles and COG repertoire among methanogens and sulphur-metabolisers, aerobic and anaerobic archaea or korarchaeota and nanoarchaeota, as elucidated in the present study, point towards the presence of distinct molecular strategies for niche specialization in the archaeal world. PMID:22691113

A pursuit of lineage-specific and niche-specific proteome features in the world of archaea.

PubMed

Roy Chowdhury, Anindya; Dutta, Chitra

2012-06-12

Archaea evoke interest among researchers for two enigmatic characteristics -a combination of bacterial and eukaryotic components in their molecular architectures and an enormous diversity in their life-style and metabolic capabilities. Despite considerable research efforts, lineage- specific/niche-specific molecular features of the whole archaeal world are yet to be fully unveiled. The study offers the first large-scale in silico proteome analysis of all archaeal species of known genome sequences with a special emphasis on methanogenic and sulphur-metabolising archaea. Overall amino acid usage in archaea is dominated by GC-bias. But the environmental factors like oxygen requirement or thermal adaptation seem to play important roles in selection of residues with no GC-bias at the codon level. All methanogens, irrespective of their thermal/salt adaptation, show higher usage of Cys and have relatively acidic proteomes, while the proteomes of sulphur-metabolisers have higher aromaticity and more positive charges. Despite of exhibiting thermophilic life-style, korarchaeota possesses an acidic proteome. Among the distinct trends prevailing in COGs (Cluster of Orthologous Groups of proteins) distribution profiles, crenarchaeal organisms display higher intra-order variations in COGs repertoire, especially in the metabolic ones, as compared to euryarchaea. All methanogens are characterised by a presence of 22 exclusive COGs. Divergences in amino acid usage, aromaticity/charge profiles and COG repertoire among methanogens and sulphur-metabolisers, aerobic and anaerobic archaea or korarchaeota and nanoarchaeota, as elucidated in the present study, point towards the presence of distinct molecular strategies for niche specialization in the archaeal world.

Synthesis of three commercial products from Bayer electrofilter powders.

PubMed

Ayala, Julia; Fernández, Begoña; Sancho, José Pedro; García, Purificación

2010-06-15

Electrofilter powders, a by-product of the Bayer process for the production of alumina from bauxite, were leached with sulphuric acid to dissolve gibbsite and transition aluminas, thus obtaining a commercial aluminium sulphate solution and a solid residue. This residue is treated again under more drastic conditions with sulphuric acidic in a furnace at a higher temperature, is then leached with water and filtered, a small amount of solid remaining (alpha-alumina). The liquid is a highly acidic aluminium sulphate solution which does not fulfil commercial grade specifications; the liquor is accordingly treated with potassium hydroxide or ammonium hydroxide to obtain potassium or ammonium alum. Experimental tests were conducted to investigate the synthesis of alum by crystallization. The effects on alum formation of various operating conditions, including the amount of potassium or ammonium hydroxide, temperature and seed alum dosage, were examined. The crystallization process was found to be quite effective in obtaining alum. Copyright 2010 Elsevier B.V. All rights reserved.

Advanced Medical Countermeasures Consortium

DTIC Science & Technology

2010-10-01

acid, gamma-linolenic acid, and antioxidants in patients with acute respiratory distress syndrome. Enteral Nutrition in ARDS Study Group. Crit Care Med...molecular mechanism of action, and (3) efficacy of countermeasures for HD injury. Studies on the Yucatan mini-pig have demonstrated that laminin in...Lindsay CD, Rice P. Changes in connective tissue macromolecular components of Yucatan mini-pig skin following application of sulphur mustard vapour. Hum

Microbial carbon metabolism associated with electrogenic sulphur oxidation in coastal sediments.

PubMed

Vasquez-Cardenas, Diana; van de Vossenberg, Jack; Polerecky, Lubos; Malkin, Sairah Y; Schauer, Regina; Hidalgo-Martinez, Silvia; Confurius, Veronique; Middelburg, Jack J; Meysman, Filip J R; Boschker, Henricus T S

2015-09-01

Recently, a novel electrogenic type of sulphur oxidation was documented in marine sediments, whereby filamentous cable bacteria (Desulfobulbaceae) are mediating electron transport over cm-scale distances. These cable bacteria are capable of developing an extensive network within days, implying a highly efficient carbon acquisition strategy. Presently, the carbon metabolism of cable bacteria is unknown, and hence we adopted a multidisciplinary approach to study the carbon substrate utilization of both cable bacteria and associated microbial community in sediment incubations. Fluorescence in situ hybridization showed rapid downward growth of cable bacteria, concomitant with high rates of electrogenic sulphur oxidation, as quantified by microelectrode profiling. We studied heterotrophy and autotrophy by following (13)C-propionate and -bicarbonate incorporation into bacterial fatty acids. This biomarker analysis showed that propionate uptake was limited to fatty acid signatures typical for the genus Desulfobulbus. The nanoscale secondary ion mass spectrometry analysis confirmed heterotrophic rather than autotrophic growth of cable bacteria. Still, high bicarbonate uptake was observed in concert with the development of cable bacteria. Clone libraries of 16S complementary DNA showed numerous sequences associated to chemoautotrophic sulphur-oxidizing Epsilon- and Gammaproteobacteria, whereas (13)C-bicarbonate biomarker labelling suggested that these sulphur-oxidizing bacteria were active far below the oxygen penetration. A targeted manipulation experiment demonstrated that chemoautotrophic carbon fixation was tightly linked to the heterotrophic activity of the cable bacteria down to cm depth. Overall, the results suggest that electrogenic sulphur oxidation is performed by a microbial consortium, consisting of chemoorganotrophic cable bacteria and chemolithoautotrophic Epsilon- and Gammaproteobacteria. The metabolic linkage between these two groups is presently unknown and needs further study.

Fermentative utilization of glycerol residue for the production of acetic acid

NASA Astrophysics Data System (ADS)

Irvan; Trisakti, B.; Hasibuan, R.; Joli, M.

2018-02-01

Glycerol residue, frequently known as pitch, is a waste produced from the downstream product of crude glycerine distillation. With the increasing need of pure glycerine in the world, the glycerol residue produced is also increasing. Glycerol residue is a solid waste at room temperature, highly alkaline (pH > 13), corrosive, and categorized as hazardous and poisonous waste. In this research, acetic acid was produced from glycerol residue through the anaerobic fermentation process by using purple non-sulphur photosynthetic bacteria. The purpose of this study was to find out the influence of concentration change of glycerol residue on time and to find out the possibility of glycerol residue to be utilized as acetic acid. In this research, at first 400 g of glycerol residue was diluted with 200 ml of distilled water to change the glycerine phase, from solid to liquid at room temperature, acidified by using hydrochloric acid until pH 2. The top layer formed was fatty acid and triglycerides that should be removed. Meanwhile, the bottom layer was diluted glycerol residue which was then neutralized with caustic soda. To produce acetic acid, glycerol residue with various concentrations, salt, and purple non-sulphur photosynthetic bacteria were put together into a 100 ml bottle which had been previously sterilized, then incubated for four weeks under the light of 40-watt bulb. The result showed that on the 28th day of fermentation, the produced acetic acid were 0.28, 1.85, and 0.2% (w/w) by using glycerine with the concentration of 0.5, 1.0, and 1.5% (w/w), respectively.

Nanosized zero-valent iron as Fenton-like reagent for ultrasonic-assisted leaching of zinc from blast furnace sludge.

PubMed

Mikhailov, Ivan; Komarov, Sergey; Levina, Vera; Gusev, Alexander; Issi, Jean-Paul; Kuznetsov, Denis

2017-01-05

Ultrasonic-assisted sulphuric acid leaching combined with a Fenton-like process, utilizing nanoscale zero-valent iron (nZVI), was investigated to enhance the leaching of zinc from the blast furnace sludge (BFS). The leaching of iron (Fe) and zinc (Zn) from the sludge was investigated using Milli-Q water/BFS ratio of 10 and varying the concentration of hydrogen peroxide, sulphuric acid, the temperature, the input energy for ultrasound irradiation, and the presence or absence of nZVI as a Fenton reagent. The results showed that with 1g/l addition of nZVI and 0.05M of hydrogen peroxide, the kinetic rate of Zn leaching increased with a maximum dissolution degree of 80.2%, after 5min treatment. In the absence of nZVI, the maximum dissolution degree of Zn was 99.2%, after 15min treatment with 0.1M of hydrogen peroxide. The rate of Zn leaching at several concentrations of hydrogen peroxide is accelerated in the presence of nZVI although a reduction in efficiency was observed. The loss of Fe was no more than 3%. On the basis of these results, the possible route for BFS recycling has been proposed (BFS slurry mixed with sulphuric acid and hydrogen peroxide is recirculated under ultrasonic irradiation then separated). Copyright © 2016 Elsevier B.V. All rights reserved.

A 3D particle Monte Carlo approach to studying nucleation

NASA Astrophysics Data System (ADS)

Köhn, Christoph; Enghoff, Martin Bødker; Svensmark, Henrik

2018-06-01

The nucleation of sulphuric acid molecules plays a key role in the formation of aerosols. We here present a three dimensional particle Monte Carlo model to study the growth of sulphuric acid clusters as well as its dependence on the ambient temperature and the initial particle density. We initiate a swarm of sulphuric acid-water clusters with a size of 0.329 nm with densities between 107 and 108 cm-3 at temperatures between 200 and 300 K and a relative humidity of 50%. After every time step, we update the position of particles as a function of size-dependent diffusion coefficients. If two particles encounter, we merge them and add their volumes and masses. Inversely, we check after every time step whether a polymer evaporates liberating a molecule. We present the spatial distribution as well as the size distribution calculated from individual clusters. We also calculate the nucleation rate of clusters with a radius of 0.85 nm as a function of time, initial particle density and temperature. The nucleation rates obtained from the presented model agree well with experimentally obtained values and those of a numerical model which serves as a benchmark of our code. In contrast to previous nucleation models, we here present for the first time a code capable of tracing individual particles and thus of capturing the physics related to the discrete nature of particles.

Ethanol addition enhances acid treatment to eliminate Lactobacillus fermentum from the fermentation process for fuel ethanol production.

PubMed

Costa, M A S; Cerri, B C; Ceccato-Antonini, S R

2018-01-01

Fermentation is one of the most critical steps of the fuel ethanol production and it is directly influenced by the fermentation system, selected yeast, and bacterial contamination, especially from the genus Lactobacillus. To control the contamination, the industry applies antibiotics and biocides; however, these substances can result in an increased cost and environmental problems. The use of the acid treatment of cells (water-diluted sulphuric acid, adjusted to pH 2·0-2·5) between the fermentation cycles is not always effective to combat the bacterial contamination. In this context, this study aimed to evaluate the effect of ethanol addition to the acid treatment to control the bacterial growth in a fed-batch system with cell recycling, using the industrial yeast strain Saccharomyces cerevisiae PE-2. When only the acid treatment was used, the population of Lactobacillus fermentum had a 3-log reduction at the end of the sixth fermentation cycle; however, when 5% of ethanol was added to the acid solution, the viability of the bacterium was completely lost even after the first round of cell treatment. The acid treatment +5% ethanol was able to kill L. fermentum cells without affecting the ethanol yield and with a low residual sugar concentration in the fermented must. In Brazilian ethanol-producing industry, water-diluted sulphuric acid is used to treat the cell mass at low pH (2·0) between the fermentative cycles. This procedure reduces the number of Lactobacillus fermentum from 10 7 to 10 4  CFU per ml. However, the addition of 5% ethanol to the acid treatment causes the complete loss of bacterial cell viability in fed-batch fermentation with six cell recycles. The ethanol yield and yeast cell viability are not affected. These data indicate the feasibility of adding ethanol to the acid solution replacing the antibiotic use, offering a low cost and a low amount of residue in the biomass. © 2017 The Society for Applied Microbiology.

Identification and distribution of sulfate reducing bacteria and sulphur-oxidising bacteria in northern South China Sea

NASA Astrophysics Data System (ADS)

Mao, S.; Zhu, X.; Guan, H.; Wu, D.; Wu, N.

2015-12-01

Fatty acids are one of the major components in modern marine sediments. It is well known that the saturated short-chain FAs were typically to be from vascular plants, algae, bacteria, and other sources, while the saturated long-chain FAs are the major components found in leaf waxes, suberin, and cutin in terrestrial higher plants. So the lipid biomarkers of fatty acids in Site 4B from Shenhu Area, northern South China Sea were investigated in Recent research supported from the 973 Program (2009CB219506), and the resources of branched fatty acids and monounsaturated fatty acids were mainly discussed. The results reveal that i/a15:0, i/a17:0, 16:1ω5, 18:1ω9 and 10me16:0 are derived from sulfate reducing bacteria (SRB), while 16:1ω7t/c and 18:1ω7 are originated from sulphur-oxidising bacteria (SOB). The biomakers of methanotrophs such as 16:1ω6/8 and 18:1ω6/8 were not detected in the sediments which coincide with more positive carbon isotope values of the fatty acids in the sediments. The stable relationship between SRB and SOB below 97cm in the sediments reflects the relative stable oxidative and reductive depositional environment which may be connected with the sulphur cycle in the sediments, that is carried out as sulfate is reduced to sulfide, and then sulfide is oxidized to sulfate and elemental sulfur, at last elemental sulfur is disproportionated to sulfide and sulfate. The frequently changed relationship of SRB and SOB above 97cm in the sediments indicates intensely changing oxidative and reductive sedimental environment, that may related with diapir structure around Site 4B, which also brings about hydrocarbon seepage leading to increasing biomass at 97cm.

The role of phosphate additive in stabilization of sulphuric-acid-based vanadium(V) electrolyte for all-vanadium redox-flow batteries

NASA Astrophysics Data System (ADS)

Roznyatovskaya, Nataliya V.; Roznyatovsky, Vitaly A.; Höhne, Carl-Christoph; Fühl, Matthias; Gerber, Tobias; Küttinger, Michael; Noack, Jens; Fischer, Peter; Pinkwart, Karsten; Tübke, Jens

2017-09-01

Catholyte in all-vanadium redox-flow battery (VRFB) which consists of vanadium salts dissolved in sulphuric acid is known to be stabilized by phosphoric acid to slow down the thermal aging at temperatures higher than 40 °C. To reveal the role of phosphoric acid, the thermally-induced aggregation is investigated using variable-temperature 51V, 31P, 17O, 1H nuclear magnetic resonance (NMR) spectroscopy and dynamic light scattering (DLS). The results indicate that the thermal stabilization of vanadium(V) electrolyte is attained by the involvement of monomeric and dimeric vanadium(V) species in the reaction with phosphoric acid which is concurrent to the formation of neutral hydroxo-aqua vanadium(V) precipitation precursor. The dimers are stabilized by counter ions due to association reaction or if such stabilization is not possible, precipitation of vanadium pentoxide is favored. The evolution of particles size distributions at 50 °C in electrolyte samples containing 1.6 M vanadium and 4.0 M total sulphate and the pathways of precipitate formation are discussed. The optimal total phosphate concentration is found to be of 0.15 M. However, the induction time is assumed to be dependent not only on the total phosphate concentrations, but also on the ratio of total vanadium(V) to sulphate concentrations.

Effect of aliphatic, monocarboxylic, dicarboxylic, heterocyclic and sulphur-containing amino acids on Leishmania spp. chemotaxis.

PubMed

Diaz, E; Zacarias, A K; Pérez, S; Vanegas, O; Köhidai, L; Padrón-Nieves, M; Ponte-Sucre, A

2015-11-01

In the sand-fly mid gut, Leishmania promastigotes are exposed to acute changes in nutrients, e.g. amino acids (AAs). These metabolites are the main energy sources for the parasite, crucial for its differentiation and motility. We analysed the migratory behaviour and morphological changes produced by aliphatic, monocarboxylic, dicarboxylic, heterocyclic and sulphur-containing AAs in Leishmania amazonensis and Leishmania braziliensis and demonstrated that L-methionine (10-12 m), L-tryptophan (10-11 m), L-glutamine and L-glutamic acid (10-6 m), induced positive chemotactic responses, while L-alanine (10-7 m), L-methionine (10-11 and 10-7 m), L-tryptophan (10-11 m), L-glutamine (10-12 m) and L-glutamic acid (10-9 m) induced negative chemotactic responses. L-proline and L-cysteine did not change the migratory potential of Leishmania. The flagellum length of L. braziliensis, but not of L. amazonensis, decreased when incubated in hyperosmotic conditions. However, chemo-repellent concentrations of L-alanine (Hypo-/hyper-osmotic conditions) and L-glutamic acid (hypo-osmotic conditions) decreased L. braziliensis flagellum length and L-methionine (10-11 m, hypo-/hyper-osmotic conditions) decreased L. amazonensis flagellum length. This chemotactic responsiveness suggests that Leishmania discriminate between slight concentration differences of small and structurally closely related molecules and indicates that besides their metabolic effects, AAs play key roles linked to sensory mechanisms that might determine the parasite's behaviour.

Chemical fingerprinting of naphthenic acids and oil sands process waters-A review of analytical methods for environmental samples.

PubMed

Headley, J V; Peru, K M; Mohamed, M H; Frank, R A; Martin, J W; Hazewinkel, R R O; Humphries, D; Gurprasad, N P; Hewitt, L M; Muir, D C G; Lindeman, D; Strub, R; Young, R F; Grewer, D M; Whittal, R M; Fedorak, P M; Birkholz, D A; Hindle, R; Reisdorph, R; Wang, X; Kasperski, K L; Hamilton, C; Woudneh, M; Wang, G; Loescher, B; Farwell, A; Dixon, D G; Ross, M; Pereira, A Dos Santos; King, E; Barrow, M P; Fahlman, B; Bailey, J; McMartin, D W; Borchers, C H; Ryan, C H; Toor, N S; Gillis, H M; Zuin, L; Bickerton, G; Mcmaster, M; Sverko, E; Shang, D; Wilson, L D; Wrona, F J

2013-01-01

This article provides a review of the routine methods currently utilized for total naphthenic acid analyses. There is a growing need to develop chemical methods that can selectively distinguish compounds found within industrially derived oil sands process affected waters (OSPW) from those derived from the natural weathering of oil sands deposits. Attention is thus given to the characterization of other OSPW components such as oil sands polar organic compounds, PAHs, and heavy metals along with characterization of chemical additives such as polyacrylamide polymers and trace levels of boron species. Environmental samples discussed cover the following matrices: OSPW containments, on-lease interceptor well systems, on- and off-lease groundwater, and river and lake surface waters. There are diverse ranges of methods available for analyses of total naphthenic acids. However, there is a need for inter-laboratory studies to compare their accuracy and precision for routine analyses. Recent advances in high- and medium-resolution mass spectrometry, concomitant with comprehensive mass spectrometry techniques following multi-dimensional chromatography or ion-mobility separations, have allowed for the speciation of monocarboxylic naphthenic acids along with a wide range of other species including humics. The distributions of oil sands polar organic compounds, particularly the sulphur containing species (i.e., OxS and OxS2) may allow for distinguishing sources of OSPW. The ratios of oxygen- (i.e., Ox) and nitrogen-containing species (i.e., NOx, and N2Ox) are useful for differentiating organic components derived from OSPW from natural components found within receiving waters. Synchronous fluorescence spectroscopy also provides a powerful screening technique capable of quickly detecting the presence of aromatic organic acids contained within oil sands naphthenic acid mixtures. Synchronous fluorescence spectroscopy provides diagnostic profiles for OSPW and potentially impacted groundwater that can be compared against reference groundwater and surface water samples. Novel applications of X-ray absorption near edge spectroscopy (XANES) are emerging for speciation of sulphur-containing species (both organic and inorganic components) as well as industrially derived boron-containing species. There is strong potential for an environmental forensics application of XANES for chemical fingerprinting of weathered sulphur-containing species and industrial additives in OSPW.

Acid extraction of molybdenum, nickel and cobalt from mineral sludge generated by rainfall water at a metal recycling plant.

PubMed

Vemic, M; Bordas, F; Guibaud, G; Comte, S; Joussein, E; Lens, P N L; Van Hullebusch, E D

2016-01-01

This study investigated the leaching yields of Mo, Ni and Co from a mineral sludge of a metal recycling plant generated by rainfalls. The investigated mineral sludge had a complex heterogeneous composition, consisting of particles of settled soil combined with metal-bearing particles (produced by catalysts, metallic oxides and battery recycling). The leaching potential of different leaching reagents (stand-alone strong acids (HNO3 (68%), H2SO4 (98%) and HCl (36%)) and acid mixtures (aqua regia (nitric + hydrochloric (1:3)), nitric + sulphuric (1:1) and nitric + sulphuric + hydrochloric (2:1:1)) was investigated at changing operational parameters (solid-liquid (S/L) ratio, leaching time and temperature), in order to select the leaching reagent which achieves the highest metal leaching yields. Sulphuric acid (98% H2SO4) was found to be the leachant with the highest metal leaching potential. The optimal leaching conditions were a three-stage successive leaching at 80 °C with a leaching time of 2 h and S/L ratio of 0.25 g L(-1). Under these conditions, the achieved mineral sludge sample leaching yields were 85.5%, 40.5% and 93.8% for Mo, Ni and Co, respectively. The higher metal leaching potential of H2SO4 in comparison with the other strong acids/acid mixtures is attributed to the fact that H2SO4 is a diacidic compound, thus it has more H(+) ions, resulting in its stronger oxidizing power and corrosiveness.

Industrial applications of new sulphur biotechnology.

PubMed

Janssen, A J; Ruitenberg, R; Buisman, C J

2001-01-01

The emission of sulphur compounds into the environment is undesirable because of their acidifying characteristics. The processing of sulphidic ores, oil refining and sulphuric acid production are major sources of SO2 emissions. Hydrogen sulphide is emitted into the environment as dissolved sulphide in wastewater or as H2S in natural gas, biogas, syngas or refinery gases. Waste streams containing sulphate are generated by many industries, including mining, metallurgical, pulp and paper and petrochemical industries. Applying process technologies that rely on the biological sulphur cycle can prevent environmental pollution. In nature sulphur compounds may cycle through a series of oxidation states (-2, 0, +2, +4, +6). Bacteria of a wide range of genera gain metabolic energy from either oxidising or reducing sulphur compounds. Paques B.V. develops and constructs reactor systems to remove sulphur compounds from aqueous and gaseous streams by utilising naturally occurring bacteria from the sulphur cycle. Due to the presence of sulphide, heavy metal removal is also achieved with very high removal efficiencies. Ten years of extensive laboratory and pilot plant research has, to date, resulted in the construction of over 30 full-scale installations. This paper presents key processes from the sulphur cycle and discusses recent developments about their application in industry.

Effect of strong acids on red mud structural and fluoride adsorption properties.

PubMed

Liang, Wentao; Couperthwaite, Sara J; Kaur, Gurkiran; Yan, Cheng; Johnstone, Dean W; Millar, Graeme J

2014-06-01

The removal of fluoride using red mud has been improved by acidifying red mud with hydrochloric, nitric and sulphuric acid. The acidification of red mud causes sodalite and cancrinite phases to dissociate, confirmed by the release of sodium and aluminium into solution as well as the disappearance of sodalite bands and peaks in infrared and X-ray diffraction data. The dissolution of these mineral phases increases the amount of available iron and aluminium oxide/hydroxide sites that are accessible for the adsorption of fluoride. However, concentrated acids have a negative effect on adsorption due to the dissolution of these iron and aluminium oxide/hydroxide sites. The removal of fluoride is dependent on the charge of iron and aluminium oxide/hydroxides on the surface of red mud. Acidifying red mud with hydrochloric, nitric and sulphuric acid resulted in surface sites of the form ≡SOH2(+) and ≡SOH. Optimum removal is obtained when the majority of surface sites are in the form ≡SOH2(+) as the substitution of a fluoride ion does not cause a significant increase in pH. This investigation shows the importance of having a low and consistent pH for the removal of fluoride from aqueous solutions using red mud. Copyright © 2014 Elsevier Inc. All rights reserved.

Rapid analytical procedure for determination of mineral oils in edible oil by GC-FID.

PubMed

Wrona, Magdalena; Pezo, Davinson; Nerin, Cristina

2013-12-15

A procedure for the determination of mineral oils in edible oil has been fully developed. The procedure consists of using a sulphuric acid-impregnated silica gel (SAISG) glass column to eliminate the fat matter. A chemical combustion of the fatty acids takes place, while the mineral oils are not affected by the sulphuric acid. The column is eluted with hexane using a vacuum pump and the final extract is concentrated and analysed by gas chromatography (GC) with flame ionisation detector (FID). The detection limit (LOD) and the quantification limit (LOQ) in hexane were 0.07 and 0.21 μg g(-1) respectively and the LOQ in vegetable oil was 1 μg g(-1). Only a few minutes were necessary for sample treatment to have a clean extract. The efficiency of the process, measured through the recoveries from spiked samples of edible oil was higher than 95%. The procedure has been applied to determine mineral oil in olive oil from the retailed market. Copyright © 2013 Elsevier Ltd. All rights reserved.

Dissolution and characterization of HEV NiMH batteries.

PubMed

Larsson, Kristian; Ekberg, Christian; Ødegaard-Jensen, Arvid

2013-03-01

Metal recovery is an essential part of the recycling of hybrid electric vehicle battery waste and the first step in a hydrometallurgical treatment is dissolution of the solid material. The properties of separated battery electrode materials were investigated. Focus was put on both the solid waste and then the dissolution behaviour. The cathode contains metallic nickel that remains undissolved when utilizing non-oxidizing conditions such as hydrochloric or sulphuric acid in combination with a low oxygen atmosphere. In these conditions the cathode active electrode material is fully dissolved. Not dissolving the nickel metal saves up to 37% of the acid consumption for the cathode electrode material. In the commonly used case of oxidizing conditions the nickel metal dissolves and a cobalt-rich phase remains undissolved from the cathode active material. For the anode material a complete and rapid dissolution can be achieved at mild conditions with hydrochloric, nitric or sulphuric acid. Optimal parameters for all cases of dissolution was pH 1 with a reaction time of approximately ≥ 20,000 s. Copyright © 2012 Elsevier Ltd. All rights reserved.

A classical reactive potential for molecular clusters of sulphuric acid and water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stinson, Jake L.; Kathmann, Shawn M.; Ford, Ian J.

2015-10-12

We present a two state empirical valence bond (EVB) potential describing interactions between sulphuric acid and water molecules and designed to model proton transfer between them within a classical dynamical framework. The potential has been developed in order to study the properties of molecular clusters of these species, which are thought to be relevant to atmospheric aerosol nucleation. The particle swarm optimisation method has been used to fit the parameters of the EVB model to density functional theory (DFT) calculations. Features of the parametrised model and DFT data are compared and found to be in satisfactory agreement. In particular, itmore » is found that a single sulphuric acid molecule will donate a proton when clustered with four water molecules at 300 K and that this threshold is temperature dependent. SMK was supported in part by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences; JLS and IJF were supported by the IMPACT scheme at University College London (UCL). We acknowledge the UCL Legion High Performance Computing Facility, and associated support services together with the resources of the National Energy Research Scientific Computing Center (NERSC), which is supported by the U.S. Department of Energy under Contract No. DE-AC02- 05CH11231. JLS thanks Dr. Gregory Schenter, Dr. Theo Kurtén and Prof. Hanna Vehkamäki for important guidance and discussions.« less

Incidence of laryngeal cancer and exposure to acid mists.

PubMed Central

Steenland, K; Schnorr, T; Beaumont, J; Halperin, W; Bloom, T

1988-01-01

To determine the relation between exposure to acid mist and laryngeal cancer, the smoking habits, drinking habits, and incidence of laryngeal cancer of 879 male steelworkers exposed to acid mists during pickling operations was ascertained. Sulphuric acid mist was the primary exposure for most men in this cohort. These men had all worked in a pickling operation for a minimum of six months before 1965, with an average duration of exposure of 9.5 years. Exposures to sulphuric acid in the 1970s averaged about 0.2 mg/m3, and earlier exposures were probably similar. Interviews were conducted with all cohort members or their next of kin in 1986 and medical records of decedents were reviewed. Nine workers were identified who had been diagnosed as having laryngeal cancer, using a conservative case definition that required medical record confirmation for any case among decedents and confirmation by a physician for any case among live individuals. Using data from national surveys of cancer incidence as referent rates, 3.44 laryngeal cancers would have been expected. Excess smoking by the exposed cohort compared with the United States population resulted in an upward adjustment of the expected number of cases of laryngeal cancer to 3.92. The standardised incidence rate ratio for laryngeal cancer was 2.30 (9/3.92), with a one sided p value of 0.01 (assuming a Poisson distribution). The finding of excess laryngeal cancer in this cohort is consistent with four other studies published since 1981. PMID:3203082

Transcripts of sulphur metabolic genes are co-ordinately regulated in developing seeds of common bean lacking phaseolin and major lectins

PubMed Central

Marsolais, Frédéric

2012-01-01

The lack of phaseolin and phytohaemagglutinin in common bean (dry bean, Phaseolus vulgaris) is associated with an increase in total cysteine and methionine concentrations by 70% and 10%, respectively, mainly at the expense of an abundant non-protein amino acid, S-methyl-cysteine. Transcripts were profiled between two genetically related lines differing for this trait at four stages of seed development using a high density microarray designed for common bean. Transcripts of multiple sulphur-rich proteins were elevated, several previously identified by proteomics, including legumin, basic 7S globulin, albumin-2, defensin, albumin-1, the Bowman–Birk type proteinase inhibitor, the double-headed trypsin inhibitor, and the Kunitz trypsin inhibitor. A co-ordinated regulation of transcripts coding for sulphate transporters, sulphate assimilatory enzymes, serine acetyltransferases, cystathionine β-lyase, homocysteine S-methyltransferase and methionine gamma-lyase was associated with changes in cysteine and methionine concentrations. Differential gene expression of sulphur-rich proteins preceded that of sulphur metabolic enzymes, suggesting a regulation by demand from the protein sink. Up-regulation of SERAT1;1 and -1;2 expression revealed an activation of cytosolic O-acetylserine biosynthesis. Down-regulation of SERAT2;1 suggested that cysteine and S-methyl-cysteine biosynthesis may be spatially separated in different subcellular compartments. Analysis of free amino acid profiles indicated that enhanced cysteine biosynthesis was correlated with a depletion of O-acetylserine. These results contribute to our understanding of the regulation of sulphur metabolism in developing seed in response to a change in the composition of endogenous proteins. PMID:23066144

Transcripts of sulphur metabolic genes are co-ordinately regulated in developing seeds of common bean lacking phaseolin and major lectins.

PubMed

Liao, Dengqun; Pajak, Agnieszka; Karcz, Steven R; Chapman, B Patrick; Sharpe, Andrew G; Austin, Ryan S; Datla, Raju; Dhaubhadel, Sangeeta; Marsolais, Frédéric

2012-10-01

The lack of phaseolin and phytohaemagglutinin in common bean (dry bean, Phaseolus vulgaris) is associated with an increase in total cysteine and methionine concentrations by 70% and 10%, respectively, mainly at the expense of an abundant non-protein amino acid, S-methyl-cysteine. Transcripts were profiled between two genetically related lines differing for this trait at four stages of seed development using a high density microarray designed for common bean. Transcripts of multiple sulphur-rich proteins were elevated, several previously identified by proteomics, including legumin, basic 7S globulin, albumin-2, defensin, albumin-1, the Bowman-Birk type proteinase inhibitor, the double-headed trypsin inhibitor, and the Kunitz trypsin inhibitor. A co-ordinated regulation of transcripts coding for sulphate transporters, sulphate assimilatory enzymes, serine acetyltransferases, cystathionine β-lyase, homocysteine S-methyltransferase and methionine gamma-lyase was associated with changes in cysteine and methionine concentrations. Differential gene expression of sulphur-rich proteins preceded that of sulphur metabolic enzymes, suggesting a regulation by demand from the protein sink. Up-regulation of SERAT1;1 and -1;2 expression revealed an activation of cytosolic O-acetylserine biosynthesis. Down-regulation of SERAT2;1 suggested that cysteine and S-methyl-cysteine biosynthesis may be spatially separated in different subcellular compartments. Analysis of free amino acid profiles indicated that enhanced cysteine biosynthesis was correlated with a depletion of O-acetylserine. These results contribute to our understanding of the regulation of sulphur metabolism in developing seed in response to a change in the composition of endogenous proteins.

In situ identification and X-ray imaging of microorganisms distribution on the Tatahouine meteorite

NASA Astrophysics Data System (ADS)

Lemelle, L.; Salomé, M.; Fialin, M.; Simionovici, A.; Gillet, Ph.

2004-10-01

Microorganisms were searched for among the complex microstructures observed on the surface of a fragment of the Tatahouine meteorite inherited from the Tunisian soil in which they were buried. In this view, the chemical compositions, particularly the nitrogen, phosphorus, and sulphur compositions, including the sulphur speciation, were investigated using scanning electron microscopy (SEM), electron probe microanalysis (EPMA) mapping, and scanning X-ray microscopy (SXM). A few 2-μm-thick filaments, partly covered by patches of calcite ensuring they were not deposited by a laboratory contamination, were observed by SEM. The EPMA maps show that the portions free of calcite of the filaments have low but constant contents of nitrogen, sulphur, and phosphorus. The SXM maps were recorded at 2473.5, 2478, and 2482.2 eV, which are respectively characteristic for amino acid linked sulphur, sulphite (SO32-), and sulphate (SO42-). The portions of the filaments detected by EPMA are also those that are enriched in amino acid linked sulphur. The calculated (N/S) elemental ratio is consistent with the one of the dehydrated Escherichia coli matter, contrary to the much lower (P/S) elemental ratio. In living cells, the bulk N and S elements are mainly located in large polymers by covalent bonds, whereas a significant amount of P belongs to small and reactive molecules. We thus can propose that the observed microstructures are dehydrated microorganisms, in which most of the elements that were composing the polymers were retained, whereas the small electrolytes and molecules were removed.

The effects of acid rainfall and heavy metal particulates on a boreal forest ecosystem near the Sudbury smelting region of Canada

Treesearch

T. C. Hutchinson

1976-01-01

Sulphur dioxide emissions have occurred on a gigantic scale at Sudbury from nickel-copper smelters. Soil erosion has followed the destruction of large areas of forest. Rainfall has been found highly acidic, frequently less than pH 3.0 in 1971. Metal accumulation in the soils (to distances of 50 km) have occurred for nickel and copper. The combination of heavy metal...

Analysis of free and bound chlorophenoxy acids in cereals.

PubMed

Lokke, H

1975-06-01

Extraction of the chlorophenoxy acids 2,4-D and dichlorprop in cereals has been examined by analyzing barley from spraying experiments. A procedure has been set up by combination of acid hydrolysis and enzymatic degradation followed by extraction and clean up on either silica gel or basic aluminum oxide. The final determination is based on reaction with diazomethane and subsequently GLC with ECD. This procedure was compared with two different extraction procedures previously described in the literature. The one comparative procedure uses a mixture of 50% diethyl ether/hexane in presence of sulphuric acid and resulted in residues up to ten times lower than found after the combined acid hydrolysis/enzymatic degradation procedure. In the second comparison a direct extraction was made with a mixture of 65% (v/v) acetonitrile in water. No differences were found between this and the combined acid hydrolysis/enzymatic degradation procedure.

The application of an integrated biogeochemical model (PnET-BGC) to five forested watersheds in the Adirondack and Catskill regions of New York

USGS Publications Warehouse

LiJun, Chen; Driscoll, C.T.; Gbondo-Tugbawa, S.; Mitchell, M.J.; Murdoch, Peter S.

2004-01-01

PnET-BGC is an integrated biogeochemical model formulated to simulate the response of soil and surface waters in northern forest ecosystems to changes in atmospheric deposition and land disturbances. In this study, the model was applied to five intensive study sites in the Adirondack and Catskill regions of New York. Four were in the Adirondacks: Constable Pond, an acid-sensitive watershed; Arbutus Pond, a relatively insensitive watershed; West Pond, an acid-sensitive watershed with extensive wetland coverage; and Willy's Pond, an acid-sensitive watershed with a mature forest. The fifth was Catskills: Biscuit Brook, an acid-sensitive watershed. Results indicated model-simulated surface water chemistry generally agreed with the measured data at all five sites. Model-simulated internal fluxes of major elements at the Arbutus watershed compared well with previously published measured values. In addition, based on the simulated fluxes, element and acid neutralizing capacity (ANC) budgets were developed for each site. Sulphur budgets at each site indicated little retention of inputs of sulphur. The sites also showed considerable variability in retention of NO3-. Land-disturbance history and in-lake processes were found to be important in regulating the output of NO3- via surface waters. Deposition inputs of base cations were generally similar at these sites. Various rates of base cation outputs reflected differences in rates of base cation supply at these sites. Atmospheric deposition was found to be the largest source of acidity, and cation exchange, mineral weathering and in-lake processes served as sources of ANC. ?? 2004 John Wiley and Sons, Ltd.

Chemistry Notes

ERIC Educational Resources Information Center

School Science Review, 1972

1972-01-01

Short articles describing the construction of a self-testing device for learning ionic formulae, problems with standard'' experiments in crystallizing sulfur, preparative details for a cold-setting adhesive and vermillion dye, and providing data related to the industrial manufacture of sulphuric acid. (AL)

Structural and wetting properties of porous anodic alumina templates prepared by different electrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suchitra, S. M., E-mail: suchitra.ph14f03@nitk.edu.in; Reddy, P. Ramana; Udayashankar, N. K.

2016-05-06

Porous anodic alumina (PAA) has been extensively studied in recent years due to their unique properties and applications for manufacturing nanostructured materials. In this article, we report our studies on structural and wetting properties of PAA membranes prepared using different electrolytes such as sulphuric, oxalic and phosphoric acids. The morphological parameters such as pore diameter and porosity were measured using SEM and analysed using image-J software. The structural investigation of PAA membranes was carried out through X-ray diffraction analysis and it was confirmed that PAA membranes were amorphous in nature. The wetting behaviour of PAA membranes were measured using contactmore » angle measurement technique. The results show that PAA membranes were hydrophilic in nature with contact angles 26.03°, 35.21° and 42.0° for sulphuric, oxalic and phosphoric acids respectively.« less

Morphological and spectroscopic analysis of cellulose nanocrystals extracted from oil palm empty fruit bunch fiber

NASA Astrophysics Data System (ADS)

Dasan, Y. K.; Bhat, A. H.; Faiz, A.

2015-07-01

This work evaluates the use of oil palm empty fruit bunch (OPEFB) fiber as a source of cellulose to obtain nanocrystalline cellulose (CNC) by acid hydrolysis reaction. The raw OPEFB fibers were pretreated with aqueous Sodium hydroxide at 80°C followed by bleaching treatment and further hydrolyzed with Sulphuric acid at 45°C with limited range of hydrolysis time and acid concentration. The resulting CNC's were characterized for spectroscopic, crystallographic and morphological properties using Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffractometer (XRD), Transmission Electron Microscope (TEM) and Atomic Force Microscopy (AFM). Finding of this study shows that the properties of CNC's are strongly dependent on the hydrolysis time and acid concentration.

Investigation of DBS electro-oxidation reaction in the aqueous-organic solution of LiClO4.

PubMed

Darlewski, Witold; Popiel, Stanisław; Nalepa, Tomasz; Gromotowicz, Waldemar; Szewczyk, Rafał; Stankiewicz, Romuald

2010-03-15

A process of dibutyl sulphide (DBS) electro-oxidation using electrolysis and cyclic voltamperometry was investigated in water-methanol solution using different electrodes (platinum, boron doped diamond, graphite and glassy carbon). Obtained results indicate that the DBS electro-oxidation process is irreversible in voltamperometric conditions. It was shown that during DBS electrolytic oxidation on Pt, at the low anode potential (1.8 V), DBS was oxidized to sulphoxide and sulphone. Electrolysis at higher potential (up to 3.0 V) resulted in complete DBS oxidation and formation of various products, including: butyric acid, sulphuric acid, butanesulphinic acid, butanesulphonic acid, identified using gas chromatography (GC-AED) and mass spectrometry (GC-MS) methods. (c) 2009 Elsevier B.V. All rights reserved.

Acidity of precipitation as influenced by the filtering of atmospheric sulphur and nitrogen compounds - its role in the element balance and effect on soil

Treesearch

Robert Mayer; Bernhard Ulrich

1976-01-01

The data presented here are based upon element balance investigations in a beech forest in Central Germany (Ellenberg 1971). Being located in an altitude of about 500 m above sea level with an annual precipitation of about 1000 mm, and an acid soil with loess as the main constituent, the test site represents a typical environment for many Central European forests....

First prokaryotic biodiversity assessment using molecular techniques of an acidic river in Neuquén, Argentina.

PubMed

Urbieta, M Sofía; González Toril, E; Aguilera, A; Giaveno, M Alejandra; Donati, E

2012-07-01

Two acidic hot springs close to the crater of Copahue Volcano (Neuquén, Argentina) are the source of the Río Agrio. The river runs several kilometres before flowing into Caviahue Lake. Along the river, temperature, iron, other metal and proton concentrations decrease gradually with distance downstream. From the source to the lake and depending on the season, pH can rise from 1.0 (or even less) to about 4.0, while temperature values decrease from 70°C to 15°C. Water samples were taken from different stations on the river selected according to their physicochemical parameters. In order to assess prokaryotic biodiversity throughout the water column, different and complementary molecular biology techniques were used, mainly in situ hybridisation and 16S rRNA gene cloning and sequencing. All microorganisms found are typical of acidic environments. Sulphur-oxidizing bacteria like Acidithiobacillus thiooxidans and Acidithiobacillus albertensis were detected in every station. Moderately thermophile iron- and sulphur-oxidizing bacteria like members of Alicyclobacillus and Sulfobacillus genera were also ubiquitous. Strict iron-oxidizing bacteria like Leptospirillum and Ferrimicrobium were present at the source of the river, but disappeared downstream where iron concentrations were much lower. Iron-oxidizing, mesophilic Ferroplasma spp. were the main archaea found. The data presented in this work represent the first molecular assessment of this rare natural acidic environment.

The Leaching of Aluminium In Spanish Clays, Coal Mining Wastes and Coal Fly Ashes by Sulphuric Acid.

NASA Astrophysics Data System (ADS)

Fernández, A. M.; Ibáñez, J. L.; Llavona, M. A.; Zapico, R.

The acid leaching of aluminium from several non traditional ores, bayerite, kaolinite, different clays, coal mining wastes and coal fly ashes, and the kinetic of their dissolution are described. The effects of time, temperature, acid concentration, sample calcination, particle size were examined. The leaching of aluminium is dependent on acid concentration and strongly on temperature. Generally, the time to reach a fixed percentage of dissolution decreases with increasing acid concentration in the range 6% to 40% acid by weight. On clays and coal mining wastes a good relation between Al removal and ratio kaolinite/illite was also observed at all temperatures and acid concentration tested. Coal fly ashes are particles that were heated at very high temperatures in the power station and Al compounds were transformed into mullite and so Al recovery was minor. Several rate equations describing the kinetics of the leach reaction were discussed and Kinetic parameters and activation energy values of samples are presented.

Effects of some pretreatments on germination of bladder-senna (Colutea armena Boiss. and Huet.) and smoke-tree (Cotinus coggygria Scop.) seeds.

PubMed

Olmez, Zafer; Yahyaoglu, Zeki; Temel, Fatih; Gokturk, Askin

2008-05-01

This study was carried out to determine effects of pre-treatments including floating in hot water(100 degrees C) followed by continual cooling for 24 hr in the same water floating in tap water for 24 hr submersion in concentrate (98%) sulphuric acid (H2SO4) and cold stratification for different durations (20, 40 and 60 days) and their combinations on seed germination and to investigate how to overcome dormancy of seeds of Colutea armena Boiss. and Huet. and Cotinus coggygria Scop. The seeds were sown in polyethylene pots in the greenhouse and on seedbeds under open field conditions. The statistical design was a randomized complete block design with three replications. The highest germination percentage (77.19%), the best germination rate (16 days) and the highest growth rate (69.01%) were obtained from Colutea armena seeds that were submersed in sulphuric acid for 30 min and sown in the greenhouse. The pre-treatment of submersion in sulphuric acid for 20 min with cold stratification for 60 days gave the highest germination percentage (82.77%) and the highest growth rate (79.37%) in the greenhouse for Cotinus coggygria seeds. On the other hand, the best germination rate (9 days) was obtained from smoketree seeds that were cold stratified 60 days and sown under open field conditions. It can be stated that there is an affirmative effect of the greenhouse condition on germination percentage and growth rate values of the seeds used in this study

Rubisco mutants of Chlamydomonas reinhardtii display divergent photosynthetic parameters and lipid allocation.

PubMed

Esquível, M G; Matos, A R; Marques Silva, J

2017-07-01

Photosynthesis and lipid allocation were investigated in Rubisco small subunit mutants of the microalga Chlamydomonas reinhardtii. Comparative analyses were undertaken with cells grown photoheterotrophically under sulphur-replete or sulphur-depleted conditions. The Y67A Rubisco mutant, which has previously demonstrated a pronounced reduction in Rubisco levels and higher hydrogen production rates than the wild type, also shows the following divergences in photosynthetic phenotype and lipid allocation: (i) low Fv/Fm (maximum photochemical efficiency), (ii) low effective quantum yield of photosystem II (ΦPSII), (iii) low effectiveness at protection against high light intensities, (iv) a higher level of total lipids per pigment and (v) changes in the relative proportions of different fatty acids, with a marked decrease in unsaturated fatty acids (FAs). The most abundant thylakoid membrane lipid, monogalactosyldiacylglycerol, decreased in amount, while the neutral lipid/polar lipid ratio increased in the mutant. The low amount and activity of the mutated Rubisco Y67A enzyme seems to have an adverse effect on photosynthesis and causes changes in carbon allocation in terms of membrane fatty acid composition and storage lipid accumulation. Our results suggest that Rubisco mutants of Chlamydomonas might be useful in biodiesel production.

Lipoic acid biosynthesis defects.

PubMed

Mayr, Johannes A; Feichtinger, René G; Tort, Frederic; Ribes, Antonia; Sperl, Wolfgang

2014-07-01

Lipoate is a covalently bound cofactor essential for five redox reactions in humans: in four 2-oxoacid dehydrogenases and the glycine cleavage system (GCS). Two enzymes are from the energy metabolism, α-ketoglutarate dehydrogenase and pyruvate dehydrogenase; and three are from the amino acid metabolism, branched-chain ketoacid dehydrogenase, 2-oxoadipate dehydrogenase, and the GCS. All these enzymes consist of multiple subunits and share a similar architecture. Lipoate synthesis in mitochondria involves mitochondrial fatty acid synthesis up to octanoyl-acyl-carrier protein; and three lipoate-specific steps, including octanoic acid transfer to glycine cleavage H protein by lipoyl(octanoyl) transferase 2 (putative) (LIPT2), lipoate synthesis by lipoic acid synthetase (LIAS), and lipoate transfer by lipoyltransferase 1 (LIPT1), which is necessary to lipoylate the E2 subunits of the 2-oxoacid dehydrogenases. The reduced form dihydrolipoate is reactivated by dihydrolipoyl dehydrogenase (DLD). Mutations in LIAS have been identified that result in a variant form of nonketotic hyperglycinemia with early-onset convulsions combined with a defect in mitochondrial energy metabolism with encephalopathy and cardiomyopathy. LIPT1 deficiency spares the GCS, and resulted in a combined 2-oxoacid dehydrogenase deficiency and early death in one patient and in a less severely affected individual with a Leigh-like phenotype. As LIAS is an iron-sulphur-cluster-dependent enzyme, a number of recently identified defects in mitochondrial iron-sulphur cluster synthesis, including NFU1, BOLA3, IBA57, GLRX5 presented with deficiency of LIAS and a LIAS-like phenotype. As in DLD deficiency, a broader clinical spectrum can be anticipated for lipoate synthesis defects depending on which of the affected enzymes is most rate limiting.

Passivation of bimetallic catalysts used in water treatment: prevention and reactivation.

PubMed

Chen, Jianming; Gillham, Robert W; Gui, Lai

2013-01-01

With respect to degradation rates and the range in contaminants treated, bimetals such as Ni-Fe or Pd-Fe generally outperform unamended granular iron. However, the catalytic enhancement is generally short-lived, lasting from a few days to months. To take advantage of the significant benefits of bimetals, this study aims at developing an effective method for the rejuvenation of passivated bimetals and alternatively, the prevention of rapid reactivity loss of bimetals. Because the most likely cause of Ni-Fe and Pd-Fe passivation is the deposition of iron oxide films over the catalyst sites, it is hypothesized that removal of the iron oxide films will restore the lost reactivity or avoiding the deposition of iron oxide films will prevent passivation. Two organic ligands (ethylenediaminetetraacetic acid (EDTA), and [s,s]-ethylenediaminedisuccinate acid ([s,s]-EDDS)) and two acids (citric acid and sulphuric acid) were tested as possible chemical reagents for both passivation rejuvenation and prevention. Trichloroethene (TCE) and Ni-Fe were chosen as probes for chlorinated solvents and bimetals respectively. The test was carried out using small glass columns packed with Ni-Fe. TCE solution containing a single reagent at various concentrations was pumped through the Ni-Fe columns with a residence time in the Ni-Fe of about 6.6 min. TCE concentrations in the influent and effluent were measured to evaluate the performance of each chemical reagent. The results show that (i) for passivated Ni-Fe, flushing with a low concentration of acid or ligand solution without mechanical mixing can fully restore the lost reactivity; and (ii) for passivation prevention, adding a small amount of a ligand or an acid to the feed solution can successfully prevent or at least substantially reduce Ni-Fe passivation. All four chemicals tested are effective in both rejuvenation and prevention, but sulphuric acid and citric acid are considered to be the most practical reagents due to their relatively low costs and environmentally friendly nature. This study suggests that the use of bimetals in above-groundwater treatment applications could become practical with appropriate engineering design.

Sulphur isotopic ratios in mosses indicating atmospheric sulphur sources in southern Chinese mountainous areas

NASA Astrophysics Data System (ADS)

Xiao, Hua-Yun; Tang, Cong-Guo; Liu, Xue-Yan; Xiao, Hong-Wei; Liu, Cong-Qiang

2008-10-01

Many mountainous regions in South China have been confronted with the consequences of acidic deposition, but studies on atmospheric S sources are still very limited. In this study, isotopic ratios in mosses were used to discriminate atmospheric S sources. A continuous increase in S isotopic ratios was observed from the south to the north in mountainous mosses and in accord with the previously reported changing trends in urban mosses, indicating a contribution of local anthropogenic S from urban cities. Based on comparisons of S isotopic ratios in mountainous mosses with those in nearby urban mosses, we found that mountainous mosses had significantly higher 34S contents than urban mosses, especially in West China, reflecting an introduction of 34S-enriched sulphur. In conjunction with cloud water data in the literature, we concluded that 34S-enriched sulphur in northerly air masses contributed much to atmospheric S in southern Chinese mountainous areas.

Extraction of uranium from tailings by sulfuric acid leaching with oxidants

NASA Astrophysics Data System (ADS)

Huang, Jing; Li, Mi; Zhang, Xiaowen; Huang, Chunmei; Wu, Xiaoyan

2017-06-01

Recovery of uranium have been performed by leaching uranium-containing tailings in sulfuric acid system with the assistance of HF, HClO4, H2O2 and MnO2. The effect of reagent dosage, sulfuric acid concentration, Liquid/solid ratio, reaction temperature and particle size on the leaching of uranium were investigated. The results show that addiction of HF, HClO4, H2O2 and MnO2 significantly increased the extraction of uranium under 1M sulphuric acid condition and under the optimum reaction conditions a dissolution fraction of 85% by HClO4, 90% by HF, 95% by H2O2 can be reached respectively. The variation of technological mineralogy properites of tailings during leaching process show that the assistants can break gangue effectively. These observations suggest that optimum oxidants could potentially influence the extraction of uranium from tailings even under dilute acid condition.

Morphological and spectroscopic analysis of cellulose nanocrystals extracted from oil palm empty fruit bunch fiber

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dasan, Y. K., E-mail: aamir.bhat@petronas.com.my; Bhat, A. H., E-mail: aamir.bhat@petronas.com.my; Faiz, A., E-mail: faizahmad@petronas.com.my

2015-07-22

This work evaluates the use of oil palm empty fruit bunch (OPEFB) fiber as a source of cellulose to obtain nanocrystalline cellulose (CNC) by acid hydrolysis reaction. The raw OPEFB fibers were pretreated with aqueous Sodium hydroxide at 80°C followed by bleaching treatment and further hydrolyzed with Sulphuric acid at 45°C with limited range of hydrolysis time and acid concentration. The resulting CNC’s were characterized for spectroscopic, crystallographic and morphological properties using Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffractometer (XRD), Transmission Electron Microscope (TEM) and Atomic Force Microscopy (AFM). Finding of this study shows that the properties of CNC’s aremore » strongly dependent on the hydrolysis time and acid concentration.« less

Feeding behaviour: hydrothermal vent crabs feast on sea 'snow'.

PubMed

Jeng, M-S; Ng, N K; Ng, P K L

2004-12-23

The crab Xenograpsus testudinatus lives at enormously high densities around the sulphur-rich hydrothermal vents found in shallow waters off Taiwan, even though this acidic environment is low in nutrients. Here we show that these crabs swarm out of their crevices at slack water and feed on the vast numbers of zooplankton that are killed by the vents' sulphurous plumes, and that rain down like marine 'snow'. This opportunistic feeding behaviour explains how the crabs are able to survive in the adverse toxic environment of these shallow hydrothermal vents.

Sulphursoil - Delano Development Corporation

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1985-06-01

A sizable amount of technical information has been accumulated on the effects of agricultural applications of the natural mineral product called Sul-Fe. This technical information supports the field observations of farmers, landscapers and gardeners who have used the product. Sul-Fe is often evaluated in terms of its sulphur content alone. When compared to elemental sulphur (100% sulphur), the 18 to 21% sulphur content of Sul-Fe seems relatively low. However, as the following technical data indicates, when judged on actual effects, Sul-Fe's complex mixture of minerals has several advantages over elemental sulphur. When judged on the basis of soil acidulation, Sul-Femore » has more immediate effects than elemental sulphur. The rapid acidifying effect is due to Sul-Fe's content of crystalline sulphuric acid. Sul-Fe also has long-term effects on soil pH due to its content of sulphur and sulfides and the time required to oxidize these materials. Elemental sulphur contains sulphur in only one chemical form which must be microbially oxidized before it becomes reactive in the soil solution, a reaction that takes quite some time in some soils. Sul-Fe is thus better than elemental sulphur in terms of immediate effects and comparable in terms of long term effects. Applied blends of Sul-Fe supplemented with elemental sulphur may provide for a maximization of both short and long term effects. An additional benefit derived from the use of Sul-Fe is the addition to the soil of a variety of trace nutrients including iron, calcium, zinc, copper, manganese, magnesium, and molybdenum.« less

Germination Conditions For Poison Ivy

Treesearch

Nathan M. Schiff; Kristina F. Connor; Margaret S. Devall

2004-01-01

Several scarification and stratification treatments were tested to optimize germination conditions for poison ivy [Toxicodendron radicans (L.) Kunst]. Fall-collected seeds soaked for 1 hour in water showed increasing germination with increasing stratification. Scarification with concentrated sulphuric acid for 30 minutes resulted in approximately 65...

Selective leaching process for the recovery of copper and zinc oxide from copper-containing dust.

PubMed

Wu, Jun-Yi; Chang, Fang-Chih; Wang, H Paul; Tsai, Ming-Jer; Ko, Chun-Han; Chen, Chih-Cheng

2015-01-01

The purpose of this study was to develop a resource recovery procedure for recovering copper and zinc from dust produced by copper smelting furnaces during the manufacturing of copper-alloy wires. The concentrations of copper in copper-containing dust do not meet the regulation standards defined by the Taiwan Environmental Protection Administration; therefore, such waste is classified as hazardous. In this study, the percentages of zinc and copper in the dust samples were approximately 38.4% and 2.6%, respectively. To reduce environmental damage and recover metal resources for industrial reuse, acid leaching was used to recover metals from these inorganic wastes. In the first stage, 2 N of sulphuric acid was used to leach the dust, with pH values controlled at 2.0-3.0, and a solid-to-liquid ratio of 1:10. The results indicated that zinc extraction efficiency was higher than 95%. A selective acid leaching process was then used to recover the copper content of the residue after filtration. In the second stage, an additional 1 N of sulphuric acid was added to the suspension in the selective leaching process, and the pH value was controlled at 1.5-2.0. The reagent sodium hydroxide (2 N) was used as leachate at a pH greater than 7. A zinc hydroxide compound formed during the process and was recovered after drying. The yields for zinc and copper were 86.9-93.5% and 97.0-98.9%, respectively.

Accurate millimetre and submillimetre rest frequencies for cis- and trans-dithioformic acid, HCSSH

NASA Astrophysics Data System (ADS)

Prudenzano, D.; Laas, J.; Bizzocchi, L.; Lattanzi, V.; Endres, C.; Giuliano, B. M.; Spezzano, S.; Palumbo, M. E.; Caselli, P.

2018-04-01

Context. A better understanding of sulphur chemistry is needed to solve the interstellar sulphur depletion problem. A way to achieve this goal is to study new S-bearing molecules in the laboratory, obtaining accurate rest frequencies for an astronomical search. We focus on dithioformic acid, HCSSH, which is the sulphur analogue of formic acid. Aims: The aim of this study is to provide an accurate line list of the two HCSSH trans and cis isomers in their electronic ground state and a comprehensive centrifugal distortion analysis with an extension of measurements in the millimetre and submillimetre range. Methods: We studied the two isomers in the laboratory using an absorption spectrometer employing the frequency-modulation technique. The molecules were produced directly within a free-space cell by glow discharge of a gas mixture. We measured lines belonging to the electronic ground state up to 478 GHz, with a total number of 204 and 139 new rotational transitions, respectively, for trans and cis isomers. The final dataset also includes lines in the centimetre range available from literature. Results: The extension of the measurements in the mm and submm range lead to an accurate set of rotational and centrifugal distortion parameters. This allows us to predict frequencies with estimated uncertainties as low as 5 kHz at 1 mm wavelength. Hence, the new dataset provided by this study can be used for astronomical search. Frequency lists are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/612/A56

Acid hydrolysis of Curcuma longa residue for ethanol and lactic acid fermentation.

PubMed

Nguyen, Cuong Mai; Nguyen, Thanh Ngoc; Choi, Gyung Ja; Choi, Yong Ho; Jang, Kyoung Soo; Park, Youn-Je; Kim, Jin-Cheol

2014-01-01

This research examines the acid hydrolysis of Curcuma longa waste, to obtain the hydrolysate containing lactic acid and ethanol fermentative sugars. A central composite design for describing regression equations of variables was used. The selected optimum condition was 4.91% sulphuric acid, 122.68°C and 50 min using the desirability function under the following conditions: the maximum reducing sugar (RS) yield is within the limited range of the 5-hydroxymethylfurfural (HMF) and furfural concentrations. Under the condition, the obtained solution contained 144 g RS/L, 0.79 g furfural/L and 2.59 g HMF/L and was directly fermented without a detoxification step. The maximum product concentration, average productivity, RS conversion and product yield were 115.36 g/L, 2.88 g/L/h, 89.43% and 64% for L-lactic acid; 113.92 g/L, 2.59 g/L/h, 88.31% and 63.29% for D-lactic acid; and 55.03 g/L, 1.38 g/L/h, 42.66 and 30.57%, respectively, for ethanol using a 7-L jar fermenter. Copyright © 2013. Published by Elsevier Ltd.

Non-canonical amino acids bearing thiophene and bithiophene: synthesis by an Ugi multicomponent reaction and studies on ion recognition ability.

PubMed

Esteves, Cátia I C; Raposo, M Manuela M; Costa, Susana P G

2017-05-01

Novel thienyl and bithienyl amino acids with different substituents were obtained by a multicomponent Ugi reaction between a heterocyclic aldehyde, an amine, an acid and an isocyanide. Due to the presence of the sulphur heterocycle at the side chain, these unnatural amino acids are highly emissive and bear extra electron donating atoms so they were tested for their ability to act as fluorescent probes and chemosensors in the recognition of biomedically relevant ions in acetonitrile and acetonitrile/water solutions. The results obtained from spectrophotometric/spectrofluorimetric titrations in the presence of organic and inorganic anions, and alkaline; alkaline-earth and transition metal cations indicated that the bithienyl amino acid bearing a methoxy group is a selective colorimetric chemosensor for Cu 2+ , while the other (bi)thienyl amino acids act as fluorimetric chemosensors with high sensitivity towards Fe 3+ and Cu 2+ in a metal-ligand complex with 1:2 stoichiometry. The photophysical and ion sensing properties of these amino acids confirm their potential as fluorescent probes suitable for incorporation into peptidic frameworks with chemosensory ability.

Airborne soil dust and its importance in buffering of atmospheric acidity and critical load assessment, over the semi arid tract of northern India.

NASA Astrophysics Data System (ADS)

Sharma, Disha; Kulshrestha, Umesh

Airborne soil dust and its importance in buffering of atmospheric acidity and critical load assessment, over the semi arid tract of northern India. The Critical Load approach alongwith integrated assessment models has been used in the European nations for policy formations to reduce acidic emissions. This unique approach was applied to assess the of vulnerability of natural systems to the present day atmospheric pollution scenario. The calculated values of critical loads of sulphur ( 225 - 275 eq/ha/yr) and nitrogen (298 - 303 eq/ha/yr), for the soil system in Delhi, were calculated with respect to Anjan grass, Hibiscus and Black siris. The present loads of sulphur (PL(S) = 26.40 eq/ha/yr) and nitrogen (PL(N) = 36.51 eq/ha/yr) were found to be much lower than their critical loads without posing any danger of atmospheric acidic deposition on the soil systems. The study indicated that the system is still protective due to high pH of soil. The nature of buffering capability of calcium derived from soil dust can be considered as a natural tool to combat acidification in the Indian region. The results showed that the pollution status in Delhi is still within the safe limits. However, at the pace at which the city is growing, it is likely that in coming decades, it may exceed these critical values. In order to set deposition limits and avoid adverse effects of acidic deposition this approach can be applied in India too. Such approach is very useful, not only in abating pollution but also in devising means of cost optimal emission abatement strategies.

Levels of cystathionine gamma lyase production by Geotrichum candidum in synthetic media and correlation with the presence of sulphur flavours in cheese.

PubMed

Gente, Stéphanie; La Carbona, Stéphanie; Guéguen, Micheline

2007-03-10

Geotrichum candidum is a cheese-ripening agent with the potential to produce sulphur flavour compounds in soft cheeses. We aimed to develop an alternative test for predicting the aromatic (sulphur flavours) potential of G. candidum strains in soft cheese. Twelve strains of G. candidum with different levels of demethiolase activity (determined by a chemical method) in YEL-met (yeast extract, lactate methionine) medium were studied. We investigated cgl (cystathionine gamma lyase) gene expression after culture in three media - YEL-met, casamino acid and curd media - and then carried out sensory analysis on a Camembert cheese matrix. We found no correlation between demethiolase activity in vitro and cgl gene expression. Sensory analysis (detection of sulphur flavours) identified different aromatic profiles linked to cgl expression, but not to demethiolase activity. The RT-PCR technique described here is potentially useful for predicting the tendency of a given strain of G. candidum to develop sulphur flavours in cheese matrix. This is the first demonstration that an in vitro molecular approach could be used as a predictive test for evaluating the potential of G. candidum strains to generate sulphur compounds in situ (Camembert cheese matrix).

Measuring protection of aromatic wine thiols from oxidation by competitive reactions vs wine preservatives with ortho-quinones.

PubMed

Nikolantonaki, Maria; Magiatis, Prokopios; Waterhouse, Andrew L

2014-11-15

Quinones are central intermediates in wine oxidation that can degrade the quality of wine by reactions with varietal thiols, such as 3-sulfanylhexanol, decreasing desirable aroma. Protection by wine preservatives (sulphur dioxide, glutathione, ascorbic acid and model tannin, phloroglucinol) was assessed by competitive sacrificial reactions with 4-methyl-1,2-benzoquinone, quantifying products and ratios by HPLC-UV-MS. Regioselectivity was assessed by product isolation and identification by NMR spectroscopy. Nucleophilic addition reactions compete with two electron reduction of quinones by sulphur dioxide or ascorbic acid, and both routes serve as effective quenching pathways, but minor secondary products from coupled redox reactions between the products and reactants are also observed. The wine preservatives were all highly reactive and thus all very protective against 3-sulfanylhexanol loss to the quinone, but showed only additive antioxidant effects. Confirmation of these reaction rates and pathways in wine is needed to assess the actual protective action of each tested preservative. Copyright © 2014 Elsevier Ltd. All rights reserved.

Temperature Effects on Stainless Steel 316L Corrosion in the Environment of Sulphuric Acid (H2SO4)

NASA Astrophysics Data System (ADS)

Ayu Arwati, I. G.; Herianto Majlan, Edy; Daud, Wan Ramli Wan; Shyuan, Loh Kee; Arifin, Khuzaimah Binti; Husaini, Teuku; Alfa, Sagir; Ashidiq, Fakhruddien

2018-03-01

In its application, metal is always in contact with its environment whether air, vapor, water, and other chemicals. During contact, chemical interactions emerge between metals and their respective environments such that the metal surface corrodes. This study aims to determine the corrosion rate of 316L stainless steel sulphuric acid environment (H2SO4) with weight loss and electrochemical methods. The corrosion rate (CR) is value of 316L stainless steel by weight loss method with sulfuric acid (H2SO4) with concentration of 0.5 M. The result obtained in conjunction with the increase of temperature the rate of erosion obtained appears to be larger, with a consecutive 3 hour the temperature of 50°C is 0.27 mg/cm2h, temperature 70°C 0.38 mg/cm2h, and temperature 90 °C 0.52 mg/cm2h. With the electrochemical method, the current value increases by using a C350 potentiostal tool. The higher the current, the longer the time the corrosion rate increases, where the current is at 90 °C with a 10-minute treatment time of 0.0014736 A. The 316L stainless steel in surface metal morphology is shown by using a Scanning Electron Microscope (SEM).

Decreasing incidence of cutaneous chemical burns in a resource limited burn centre: is this a positive effect of modernization?

PubMed

Nnabuko, R E E; Okoye, C P; Ogbonnaya, I S; Isiwele, Egi

2017-01-01

Burns present a devastating injury to patients. Burns caused by chemical agents, present a worse scenario. In a resource limited country like Nigeria, readily available sources of these corrosive agents are mainly from lead-acid battery vendors and to some extent local small scale soap manufacturers who use caustic soda. We hypothesized that with the reduction in small scale soap manufacturing and increasing trend towards modernization in the use of dry cell batteries, chemical burns may be on the decline, and we sought to investigate this. The records of all acute burn patients seen at the Burns and Plastic Department of the National Orthopaedic Hospital Enugu Nigeria between January 2011 and December 2014 were retrospectively reviewed. The results were compared to similar studies carried out at the same centre. A questionnaire was administered to corrosive chemical (sulphuric and caustic soda) vendors to assess the trends in product sales and use in recent times. A total of 624 acute burn cases were treated during the period; among which, 12 cases (1.9%) were chemical burns. When compared with previous studies at the centre, Chemical burn cases were  recorded as the lowest rate. The median age of patients was 24 years. There were eight males and four females. Interpersonal assault was the commonest mechanism of injury with sulphuric acid suspected to be the commonest agent in 83.3% of the cases, while 16.7% of the cases were from accidental use of caustic soda. The head and neck as well as the upper limbs were the most affected (30%). Twenty-six questionnaires to lead-acid vendors were analyzed and revealed that all respondents noticed a marked downward trend in the sale of either sulphuric acid or caustic soda, and they attributed this to the ready availability of imported alternatives to locally manufactured soap or wet lead-acid batteries. Ease of use, durability and convenience of the dry cell batteries were cited as principal reasons. There appears to be a downward trend in the prevalence of chemical burns in our study compared to previous studies in the centre which may be due to reduced availability and access of corrosive chemicals to the general public. Further prospective multicentre studies to confirm this are recommended.

Superficial alteration mineralogy in active volcanic systems: An example of Poás volcano, Costa Rica

NASA Astrophysics Data System (ADS)

Rodríguez, Alejandro; van Bergen, Manfred J.

2017-10-01

The alteration mineralogy in the crater area of Poás volcano (Costa Rica) has been studied to constrain acid fluid-rock interaction processes and conditions relevant for the formation of sulphate-bearing mineral assemblages found on the surface of Mars. Individual sub-environments, which include the hyperacid lake (Laguna Caliente), ephemeral hot springs, fumarole vents and areas affected by acid rain and/or spray from the lake, are marked by distinct secondary mineral associations, with sulphates commonly as prevailing component. The sulphates occur in a wide mineralogical diversity comprising gypsum/anhydrite, various polyhydrated Al-sulphates, alunite-jarosite group minerals, halotrichite-, voltaite- and copiapite-group minerals, epsomite and römerite. Depending on the sub-environment, they are variably associated with clay minerals (kaolinite-group and smectite-group), zeolites, SiO2-polymorphs, Fe-(hydro)oxides, Ti-oxides, native sulphur, sulphides, chlorides, fluorides, phosphates and carbonates. Geochemical modelling was performed to identify mechanisms responsible for the formation of the secondary minerals found in the field, and to predict their possible stability under conditions not seen at the surface. The results indicate that the appearance of amorphous silica, hematite, anhydrite/gypsum, pyrite, anatase and kaolinite is relatively insensitive to the degree of acidity of the local aqueous system. On the other hand, alunite-jarosite group minerals, elemental sulphur and Al(OH)SO4 only form under acidic conditions (pH < 4). The presence of polyhydrated Mg- and Fe2 +-sulphates is restricted to olivine-bearing rocks exposed to acid rain or brine spray. Modelling suggests that their formation required a repetitive sequence of olivine dissolution and evaporation in an open system involving limited amounts of fluid. The mineral variety in the crater of Poás is remarkably similar to sulphate-bearing assemblages considered to be the product of acid-sulphate alteration on Mars. The analogy suggests that comparable fluid-rock interaction controls operated in Martian volcanic environments.

Radioactivity contents in dicalcium phosphate and the potential radiological risk to human populations.

PubMed

Casacuberta, N; Masqué, P; Garcia-Orellana, J; Bruach, J M; Anguita, M; Gasa, J; Villa, M; Hurtado, S; Garcia-Tenorio, R

2009-10-30

Potentially harmful phosphate-based products derived from the wet acid digestion of phosphate rock represent one of the most serious problems facing the phosphate industry. This is particularly true for dicalcium phosphate (DCP), a food additive produced from either sulphuric acid or hydrochloric acid digestion of raw rock material. This study determined the natural occurring radionuclide concentrations of 12 DCP samples and 4 tricalcium phosphate (TCP) samples used for animal and human consumption, respectively. Metal concentrations (Al, Fe, Zn, Cd, Cr, As, Hg, Pb and Mg) were also determined. Samples were grouped into three different clusters (A, B, C) based on their radionuclide content. Whereas group A is characterized by high activities of 238U, 234U (approximately 10(3) Bq kg(-1)), 210Pb (2 x 10(3) Bq kg(-1)) and (210)Po ( approximately 800 Bq kg(-1)); group B presents high activities of (238)U, (234)U and (230)Th (approximately 10(3) Bq kg(-1)). Group C was characterized by very low activities of all radionuclides (< 50 Bq kg(-1)). Differences between the two groups of DCP samples for animal consumption (groups A and B) were related to the wet acid digestion method used, with group A samples produced from hydrochloric acid digestion, and group B samples produced using sulphuric acid. Group C includes more purified samples required for human consumption. High radionuclide concentrations in some DCP samples (reaching 2 x 10(3) and 10(3) Bq kg(-1) of 210Pb and 210Po, respectively) may be of concern due to direct or indirect radiological exposure via ingestion. Our experimental results based on 210Pb and 210Po within poultry consumed by humans, suggest that the maximum radiological doses are 11 +/- 2 microSv y(-1). While these results suggest that human health risks are small, additional testing should be conducted.

Amino acid composition of two masticatory nuts (Cola acuminata and Garcinia kola) and a snack nut (Anacardium occidentale).

PubMed

Adeyeye, E I; Asaolu, S S; Aluko, A O

2007-06-01

The amino acid compositions of Cola acuminata, Garcinia kola and Anacardium occidentale were evaluated by ion-exchange chromatography. Glutamic acid was the most concentrated acid in the samples. In all the amino acids determined, A. occidentale had the most concentrated acid on a pairwise basis. The total amino acids were 356.24 mg/g protein, 112.90 mg/g protein and 659.17 mg/g protein for C. acuminata, G. kola and A. occidentale, respectively. The percentage total essential amino acids were 38.39% (C. acuminata), 47.05% (G. kola) and 51.04% (A. occidentale). Also the percentage total acidic amino acids were 38.16% (C. acuminata), 30.61% (G. kola) and 30.35% (A. occidentale). The calculated isoelectric points were 2.0 (C. acuminata), 0.7 (G. kola) and 3.9 (A. occidentale), showing they can all be precipitated at acidic pH. While threonine was the limiting amino acid in A. occidentale, it was valine in both C. acuminata and G. kola. The percentage cystine (Cys) levels in the total sulphur amino acid were 44.27% (C. acuminata), 37.75% (G. kola) and 50.51% (A. occidentale). The aim of this work was to compare the amino acid profile of the samples. It is recommended that C. acuminata and G. kola consumption be avoided by ulcer patients because of their high levels of acidic amino acids. A. occidentale amino acid scores ranged from 42% to 127%, suggesting that it could be used to enhance the protein quality of cereals through food complementation.

Synthesis, spectral features and biological activity of some novel hetarylazo dyes derived from 6-amino-1,3-dimethyluracil

NASA Astrophysics Data System (ADS)

Yousefi, Hessamoddin; Yahyazadeh, Asieh; Yazdanbakhsh, Mohammad Reza; Rassa, Mehdi; Moradi-e-Rufchahi, Enayat O.'llah

2012-05-01

A series of hetarylazoaminouracil dyes were prepared by coupling of 6-amino-1,3-dimethyluracil with eight diazotized heterocyclic amines in nitrosyl sulphuric acid. The prepared azo dyes were characterized by UV-Vis, FT-IR, 13C NMR, 1H NMR spectroscopic techniques and elemental analysis. The solvatochromism of dyes was evaluated with respect to wavelength of maximum absorption (λmax) in seven solvents with different polarities: acetic acid, methanol, water, chloroform, acetonitrile, dimethyl sulfoxide and dimethyl formamide. The effects of acid, base and concentration of the dye on the visible absorption spectra were also reported. In addition, the antimicrobial activity of the synthesized dyes was evaluated on Escherichia coli, Bacillus subtilis, Micrococcus leuteus and Pseudomonas aeruginosa.

The utilization of leftover as acid catalyst to catalyse the transesterification and esterification reactions

NASA Astrophysics Data System (ADS)

Leung, K. K.; Yau, Y. H.

2017-08-01

Biodiesel (Fatty Acid Methyl Ester, FAME) is a green and renewable energy. It is carbon neutral and produces less air pollutants in combustion. In my project, the selected feedstock of biodiesel production is grease trap oil (GTO). It is extracted from restaurants, and needs pre-treatment. The triglycerides and free fatty acid (FFA) are the main components of GTO. Both triglycerides and free fatty acid can be converted to biodiesel (Fatty Acid Methyl Ester) by transesterification and esterification, through reaction with alcohol (methanol) and catalyst. In the processes, acidic catalyst is chosen to speed up the reactions. The catalyst used In the study, a heterogeneous solid acid is applied. It is waste cooked rice (WCR) collected from leftover. The WCR powder is pyrolysed in 400°C furnace 15 hours and blown with nitrogen gas (incomplete carbonization). The WCR black powder is then mixed with concentrated sulphuric acid and heat in 160°C furnace 15 hours and continuous blown with nitrogen gas (sulphonation). This heterogeneous solid acid is used in the both transesterification and esterification to produce FAME. Moreover, in the optimal reaction conditions, this catalyst offers a stable catalytic effect. After 20 times usage in optimal reaction condition, the catalytic activity remains unchanged.

Determination of sulphur in various vegetables by solid sampling high-resolution electrothermal molecular absorption spectrometry.

PubMed

Gunduz, Sema; Akman, Suleyman

2015-04-01

Sulphur was determined in various vegetables via molecular absorption of carbon monosulphide (CS) at 258.056 nm using a solid sampling high resolution continuum source electrothermal atomic absorption spectrometer (SS HR-CS ETAAS). Samples were dried, ground and directly introduced into the ruthenium coated graphite furnace as 0.05 to 0.50mg. All determinations were performed using palladium+citric acid modifier and applying a pyrolysis temperature of 1000 °C and a volatilisation temperature of 2400 °C. The results were in good agreement with certified sulphur concentrations of various vegetal CRM samples applying linear calibration technique prepared from thioacetamide. The limit of detection and characteristic mass of the method were 7.5 and 8.7 ng of S, respectively. The concentrations of S in various spinach, leek, lettuce, radish, Brussels sprouts, zucchini and chard samples were determined. It was showed that distribution of sulphur in CRM and grinded food samples were homogeneous even in micro-scale. Copyright © 2014 Elsevier Ltd. All rights reserved.

Long-term sulphur starvation of Arabidopsis thaliana modifies mitochondrial ultrastructure and activity and changes tissue energy and redox status.

PubMed

Ostaszewska, Monika; Juszczuk, Izabela M; Kołodziejek, Izabella; Rychter, Anna M

2014-04-15

Sulphur, as a constituent of amino acids (cysteine and methionine), iron-sulphur clusters, proteins, membrane sulpholipids, glutathione, glucosinolates, coenzymes, and auxin precursors, is essential for plant growth and development. Absence or low sulphur concentration in the soil results in severe growth retardation. Arabidopsis thaliana plants grown hydroponically for nine weeks on Knop nutrient medium without sulphur showed morphological symptoms of sulphur deficiency. The purpose of our study was to investigate changes that mitochondria undergo and the role of the highly branched respiratory chain in survival during sulphur deficiency stress. Ultrastructure analysis of leaf mesophyll cells of sulphur-deficient Arabidopsis showed heterogeneity of mitochondria; some of them were not altered, but the majority had swollen morphology. Dilated mitochondria displayed a lower matrix density and fewer cristae compared to control mitochondria. Disintegration of the inner and outer membranes of some mitochondria from the leaves of sulphur-deficient plants was observed. On the contrary, chloroplast ultrastructure was not affected. Sulphur deficiency changed the respiratory activity of tissues and isolated mitochondria; Complex I and IV capacities and phosphorylation rates were lower, but external NAD(P)H dehydrogenase activity increased. Higher external NAD(P)H dehydrogenase activity corresponded to increased cell redox level with doubled NADH/NAD ratio in the leaf and root tissues. Sulphur deficiency modified energy status in the tissues of Arabidopsis plants. The total concentration of adenylates (expressed as ATP+ADP), measured in the light, was lower in the leaves and roots of sulphur-deficient plants than in the controls, which was mainly due to the severely decreased ATP levels. We show that the changes in mitochondrial ultrastructure are compensated by the modifications in respiratory chain activity. Although mitochondria of Arabidopsis tissues are affected by sulphur deficiency, their metabolic and structural features, which readily reach new homeostasis, make these organelles crucial for adaptation of plants to survive sulphur deficiency. Copyright © 2013 Elsevier GmbH. All rights reserved.

Technological pretreatment of the synchysite non-oxidized ore

NASA Astrophysics Data System (ADS)

Munkhtsetseg, B.; Burmaa, G.

2013-06-01

Mongolia has rich deposits of rare, precious, and poly-metallic ores. Nowadays, it is important to research separation of rare earth elements oxides concentrates from the ores, analyze their unique physical chemical characteristics, and purified it. Our investigation on raw materials focuses on rare earth non-oxidized ores. Main mineral in this rock sample is Synchysite (LnCa(CO3)2F. We did technological and thermal pretreatment: direct sulphurization (H2SO4), sulphurization with subsequent roasting (800°C+H2SO4), sulphurization prior to roasting (H2SO4+650°C). Sulphurization method based on dissolution of rare earth mineral into sulfuric acid (93%) according to the reaction. The amount of rare earth element oxides is almost 10 times greater (29.16%) after direct sulphurization process, almost 8 times greater (21.14%) after sulphurization with subsequent roasting, and almost 20 times greater (44.62%) after sulphurization prior to roasting process. After those technological pretreatment raw material's micro elements Thorium and Uranium contents are reduced as follows: H2SO4>800°C+H2SO4>H2SO4+650°C. These results show that cerium group rare earth elements have very good solubility in water at +2°C temperature and decreasing micro elements content uranium and thorium good pretreatment condition is prior to roasting (H2SO4+650°C) of synchysite non-oxidized ore.

Inhibition of bacterial activity in acid mine drainage

NASA Astrophysics Data System (ADS)

Singh, Gurdeep; Bhatnagar, Miss Mridula

1988-12-01

Acid mine drainage water give rise to rapid growth and activity of an iron- and sulphur- oxidizing bacterium Thiobacillus ferrooxidians which greatly accelerate acid producing reactions by oxidation of pyrite material associated with coal and adjoining strata. The role of this bacterium in production of acid mine drainage is described. This study presents the data which demonstrate the inhibitory effect of certain organic acids, sodium benzoate, sodium lauryl sulphate, quarternary ammonium compounds on the growth of the acidophilic aerobic autotroph Thiobacillus ferrooxidians. In each experiment, 10 milli-litres of laboratory developed culture of Thiobacillus ferrooxidians was added to 250 milli-litres Erlenmeyer flask containing 90 milli-litres of 9-k media supplemented with FeSO4 7H2O and organic compounds at various concentrations. Control experiments were also carried out. The treated and untreated (control) samples analysed at various time intervals for Ferrous Iron and pH levels. Results from this investigation showed that some organic acids, sodium benzoate, sodium lauryl sulphate and quarternary ammonium compounds at low concentration (10-2 M, 10-50 ppm concentration levels) are effective bactericides and able to inhibit and reduce the Ferrous Iron oxidation and acidity formation by inhibiting the growth of Thiobacillus ferrooxidians is also discussed and presented

Anodic oxidation of commercially pure titanium for purification of polluted water

NASA Astrophysics Data System (ADS)

Benkafada, Faouzia; Kerdoud, Djahida; Bouchoucha, Ali

2018-05-01

Anodisation of pure titanium has been carried out in sulphuric acid solution at potentials ranging from 40 V to 5 days. We studied the parameters influencing the anodic deposition such as acid concentration and anodic periods. Anodic oxides thin films were characterized by X-ray diffraction, cyclic polarization and electrochemical impedance spectroscopy. The I-V curves and electrochemical impedance measurements were carried out in 0.1 N NaOH solution. The results indicated that although the thin films obtained by anodic oxidation are nonstoichiometric, they have an electric behaviour like n-type semiconducting material.

Influence of poly(aminoquinone) on corrosion inhibition of iron in acid media

NASA Astrophysics Data System (ADS)

Jeyaprabha, C.; Sathiyanarayanan, S.; Phani, K. L. N.; Venkatachari, G.

2005-11-01

The inhibitor performance of chemically synthesized water soluble poly(aminoquinone) (PAQ) on iron corrosion in 0.5 M sulphuric acid was studied in relation to inhibitor concentration using potentiodynamic polarization and electrochemical impedance spectroscopy measurements. On comparing the inhibition performance of PAQ with that of the monomer o-phenylenediamine (OPD), the OPD gave an efficiency of 80% for 1000 ppm while it was 90% for 100 ppm of PAQ. PAQ was found to be a mixed inhibitor. Besides, PAQ was able to improve the passivation tendency of iron in 0.5 M H 2SO 4 markedly.

Bulk deposition of base cationic nutrients in China's forests: Annual rates and spatial characteristics

Treesearch

Enzai Du; Wim de Vries; Steven McNulty; Mark E. Fenn

2018-01-01

Base cations, such as potassium (K+), calcium (Ca2+) and magnesium (Mg2+), are essential nutrients for plant growth and their atmospheric inputs can buffer the effect of acid deposition by nitrogen (N) and sulphur (S) compounds. However, the spatial variation in atmospheric deposition of these base...

Knowledge management system for risk mitigation in supply chain uncertainty: case from automotive battery supply chain

NASA Astrophysics Data System (ADS)

Marie, I. A.; Sugiarto, D.; Surjasa, D.; Witonohadi, A.

2018-01-01

Automotive battery supply chain include battery manufacturer, sulphuric acid suppliers, polypropylene suppliers, lead suppliers, transportation service providers, warehouses, retailers and even customers. Due to the increasingly dynamic condition of the environment, supply chain actors were required to improve their ability to overcome various uncertainty issues in the environment. This paper aims to describe the process of designing a knowledge management system for risk mitigation in supply chain uncertainty. The design methodology began with the identification of the knowledge needed to solve the problems associated with uncertainty and analysis of system requirements. The design of the knowledge management system was described in the form of a data flow diagram. The results of the study indicated that key knowledge area that needs to be managed were the knowledge to maintain the stability of process in sulphuric acid process and knowledge to overcome the wastes in battery manufacturing process. The system was expected to be a media acquisition, dissemination and storage of knowledge associated with the uncertainty in the battery supply chain and increase the supply chain performance.

Solar eclipse demonstrating the importance of photochemistry in new particle formation

NASA Astrophysics Data System (ADS)

Jokinen, Tuija; Kontkanen, Jenni; Lehtipalo, Katrianne; Manninen, Hanna E.; Aalto, Juho; Porcar-Castell, Albert; Garmash, Olga; Nieminen, Tuomo; Ehn, Mikael; Kangasluoma, Juha; Junninen, Heikki; Levula, Janne; Duplissy, Jonathan; Ahonen, Lauri R.; Rantala, Pekka; Heikkinen, Liine; Yan, Chao; Sipilä, Mikko; Worsnop, Douglas R.; Bäck, Jaana; Petäjä, Tuukka; Kerminen, Veli-Matti; Kulmala, Markku

2017-04-01

Solar eclipses provide unique possibilities to investigate atmospheric processes, such as new particle formation (NPF), important to the global aerosol load and radiative balance. The temporary absence of solar radiation gives particular insight into different oxidation and clustering processes leading to NPF. This is crucial because our mechanistic understanding on how NPF is related to photochemistry is still rather limited. During a partial solar eclipse over Finland in 2015, we found that this phenomenon had prominent effects on atmospheric on-going NPF. During the eclipse, the sources of aerosol precursor gases, such as sulphuric acid and nitrogen- containing highly oxidised organic compounds, decreased considerably, which was followed by a reduced formation of small clusters and nanoparticles and thus termination of NPF. After the eclipse, aerosol precursor molecule concentrations recovered and re-initiated NPF. Our results provide direct evidence on the key role of the photochemical production of sulphuric acid and highly oxidized organic compounds in maintaining atmospheric NPF. Our results also explain the rare occurrence of this phenomenon under dark conditions, as well as its seemingly weak connection with atmospheric ions.

Solar eclipse demonstrating the importance of photochemistry in new particle formation

PubMed Central

Jokinen, Tuija; Kontkanen, Jenni; Lehtipalo, Katrianne; Manninen, Hanna E.; Aalto, Juho; Porcar-Castell, Albert; Garmash, Olga; Nieminen, Tuomo; Ehn, Mikael; Kangasluoma, Juha; Junninen, Heikki; Levula, Janne; Duplissy, Jonathan; Ahonen, Lauri R.; Rantala, Pekka; Heikkinen, Liine; Yan, Chao; Sipilä, Mikko; Worsnop, Douglas R.; Bäck, Jaana; Petäjä, Tuukka; Kerminen, Veli-Matti; Kulmala, Markku

2017-01-01

Solar eclipses provide unique possibilities to investigate atmospheric processes, such as new particle formation (NPF), important to the global aerosol load and radiative balance. The temporary absence of solar radiation gives particular insight into different oxidation and clustering processes leading to NPF. This is crucial because our mechanistic understanding on how NPF is related to photochemistry is still rather limited. During a partial solar eclipse over Finland in 2015, we found that this phenomenon had prominent effects on atmospheric on-going NPF. During the eclipse, the sources of aerosol precursor gases, such as sulphuric acid and nitrogen- containing highly oxidised organic compounds, decreased considerably, which was followed by a reduced formation of small clusters and nanoparticles and thus termination of NPF. After the eclipse, aerosol precursor molecule concentrations recovered and re-initiated NPF. Our results provide direct evidence on the key role of the photochemical production of sulphuric acid and highly oxidized organic compounds in maintaining atmospheric NPF. Our results also explain the rare occurrence of this phenomenon under dark conditions, as well as its seemingly weak connection with atmospheric ions. PMID:28374761

Chemical durability of glaze on Zsolnay architectural ceramics (Budapest, Hungary) in acid solutions

NASA Astrophysics Data System (ADS)

Baricza, Ágnes; Bajnóczi, Bernadett; May, Zoltán; Tóth, Mária; Szabó, Csaba

2015-04-01

Zsolnay glazed architectural ceramics are among the most famous Hungarian ceramics, however, there is no profound knowledge about the deterioration of these building materials. The present study aims to reveal the influence of acidic solutions in the deterioration of Zsolnay ceramics. The studied ceramics are glazed roof tiles, which originate from two buildings in Budapest: one is located in the densely built-up city centre with high traffic rate and another one is in a city quarter with moderate traffic and more open space. The roof tiles represent the construction and the renovation periods of the buildings. The ceramics were mainly covered by lead glazes in the construction period and mainly alkali glazes in the renovation periods. The glaze of the tiles were coloured with iron (for yellow glaze) or chromium/copper/iron (for green glazes) in the case of the building located in the city centre, whereas cobalt was used as colorant and tin oxide as opacifier for the blue glaze of the ceramics of the other building. Six tiles were selected from each building. Sulphuric acid (H2SO4) solutions of pH2 and pH4 were used to measure the durability of the glazes up to 14 days at room temperature. The surfaces of the glazed ceramics after the treatment were measured by X-ray diffraction, Raman spectroscopy and SEM-EDS techniques to determine the precipitated phases on the surface of the glaze. Electron microprobe analysis was used to quantitatively characterise phases found and to determine the chemical composition of the treated glaze. The recovered sulphuric acid solutions were measured with ICP-OES technique in order to quantify the extent of the ion exchange between the glaze and the solutions. There is a significant difference in the dissolution rates in the treatments with sulphuric acid solutions of pH2 and pH4, respectively. The solution of pH2 induced greater ion exchange (approx. 7-10 times) from the glaze compared to the solution of pH4. Alkali and alkali earth metals and lead indicate the most intensive dissolution. Greater amount of ion-exchange was observed for the lead glaze covering the ceramics from the construction periods of both buildings. Sulphate phases (e.g. anglesite, gypsum, anhydrite) newly appeared on corroded glaze parts and pits are clearly seen on the surface of the ceramics originated especially from the first renovation period of the building located in the city centre.

Effect of acid hydrolysis and fungal biotreatment on agro-industrial wastes for obtainment of free sugars for bioethanol production.

PubMed

El-Tayeb, T S; Abdelhafez, A A; Ali, S H; Ramadan, E M

2012-10-01

This study was designed to evaluate selected chemical and microbiological treatments for the conversion of certain local agro-industrial wastes (rice straw, corn stalks, sawdust, sugar beet waste and sugarcane bagasse) to ethanol. The chemical composition of these feedstocks was determined. Conversion of wastes to free sugars by acid hydrolysis varied from one treatment to another. In single-stage dilute acid hydrolysis, increasing acid concentration from 1 % (v/v) to 5 % (v/v) decreased the conversion percentage of almost all treated agro-industrial wastes. Lower conversion percentages for some treatments were obtained when increasing the residence time from 90 to 120 min. The two-stage dilute acid hydrolysis by phosphoric acid (1.0 % v/v) followed by sulphuric acid (1.0 % v/v) resulted in the highest conversion percentage (41.3 % w/w) on treated sugar beet waste. This treatment when neutralized, amended with some nutrients and inoculated with baker's yeast, achieved the highest ethanol concentration (1.0 % v/v). Formation of furfural and hydroxymethylfurfural (HMF) were functions of type of acid hydrolysis, acid concentration, residence time and feedstock type. The highest bioconversion of 5 % wastes (37.8 % w/w) was recorded on sugar beet waste by Trichoderma viride EMCC 107. This treatment when followed by baker's yeast fermentation, 0.41 % (v/v) ethanol and 8.2 % (v/w) conversion coefficient were obtained.

Effect of acid hydrolysis and fungal biotreatment on agro-industrial wastes for obtainment of free sugars for bioethanol production

PubMed Central

El-Tayeb, T.S.; Abdelhafez, A.A.; Ali, S.H.; Ramadan, E.M.

2012-01-01

This study was designed to evaluate selected chemical and microbiological treatments for the conversion of certain local agro-industrial wastes (rice straw, corn stalks, sawdust, sugar beet waste and sugarcane bagasse) to ethanol. The chemical composition of these feedstocks was determined. Conversion of wastes to free sugars by acid hydrolysis varied from one treatment to another. In single-stage dilute acid hydrolysis, increasing acid concentration from 1 % (v/v) to 5 % (v/v) decreased the conversion percentage of almost all treated agro-industrial wastes. Lower conversion percentages for some treatments were obtained when increasing the residence time from 90 to 120 min. The two-stage dilute acid hydrolysis by phosphoric acid (1.0 % v/v) followed by sulphuric acid (1.0 % v/v) resulted in the highest conversion percentage (41.3 % w/w) on treated sugar beet waste. This treatment when neutralized, amended with some nutrients and inoculated with baker’s yeast, achieved the highest ethanol concentration (1.0 % v/v). Formation of furfural and hydroxymethylfurfural (HMF) were functions of type of acid hydrolysis, acid concentration, residence time and feedstock type. The highest bioconversion of 5 % wastes (37.8 % w/w) was recorded on sugar beet waste by Trichoderma viride EMCC 107. This treatment when followed by baker’s yeast fermentation, 0.41 % (v/v) ethanol and 8.2 % (v/w) conversion coefficient were obtained. PMID:24031984

Linking autotrophic activity in environmental samples with specific bacterial taxa by detection of 13C-labelled fatty acids.

PubMed

Knief, Claudia; Altendorf, Karlheinz; Lipski, André

2003-11-01

A method for the detection of physiologically active autotrophic bacteria in complex microbial communities was developed based on labelling with the stable isotope 13C. Labelling of autotrophic nitrifying, sulphur-oxidizing and iron-oxidizing populations was performed in situ by incubation with NaH[13C]O3. Incorporated label into fatty acid methyl esters (FAMEs) was detected and quantified using gas chromatography-mass spectrometry in single ion monitoring mode. Before the analyses of different environmental samples, the protocol was evaluated in pure culture experiments. In different environmental samples a selective labelling of fatty acids demonstrated which microbial taxa were responsible for the respective chemolithoautotrophic activity. The most strongly labelled fatty acids of a sample from a sulphide treating biofilter from an animal rendering plant were cis-7-hexadecenoic acid (16:1 cis7) and 11-methyl hexadecanoic acid (16:0 11methyl), which are as-yet not known for any sulphide-oxidizing autotroph. The fatty acid labelling pattern of an experimental biotrickling filter sample supplied with dimethyl disulphide clearly indicated the presence and activity of sulphide-oxidizing bacteria of the genus Thiobacillus. For a third environmental sample from an acid mining lake sediment, the assignment of autotrophic activity to bacteria of the genus Leptospirillum but not to Acidithiobacillus could be made by this method, as the fatty acid patterns of these bacteria show clear differences.

Megacity pollution by modern Diesel cars: New insights into the nature and formation of volatile nano-particles with high lung intrusion efficiency

NASA Astrophysics Data System (ADS)

Arnold, F.; Reichl, U.; Muschik, Ch.; Roiger, A.; Schlager, H.; Pirjola, L.; Rönkkö, T.; Keskinen, J.; Rothe, D.; Lähde, T.

2009-04-01

Aerosol particles generated by Diesel vehicles represent mayor health affecting air pollutants in cities and near motor ways. To mitigate the Diesel particle pollution problem, Diesel vehicles become increasingly fitted or retro-fitted with modern exhaust after treatment systems (ATS), which remove most engine-generated primary particles, particularly soot. Unfortunately however, ATS have undesired side effects including also the formation of low vapour pressure gases, which may undergo nucleation and condensation leading to volatile nucleation particles (NUP). NUP are substantially smaller (diameters: 5-15 nm) than soot particles (diameters: 40-100 nm), and therefore may be termed real nano-particles. NUP can intrude with maximum efficiency the lowest, least protected, and most vulnerable compartment of the human lung. However, the chemical nature and mechanism of formation of NUP are only poorly explored. Using a novel mass spectrometric method, we have made the first on line and off line measurements of low vapour pressure NUP precursor gases in the exhaust of a modern heavy duty Diesel vehicle engine, operated with and without ATS and combusting low and ultra-low sulphur fuels including also bio fuel. In addition, we have made accompanying NUP measurements and NUP model simulations. The on line measurements involved a CIMS (Chemical Ionization Mass Spectrometry) method originally developed by MPIK. They took place directly in the Diesel exhaust and had a large sensitivity and a fast time response (1 s). The off line measurements involved adsorption of exhaust gases on stainless steel, followed by thermo desorption and detection of desorbed exhaust molecules by CIMS. We find that modern Diesel ATS strongly increase the formation of hydroxyl radicals, which induce conversion of fuel sulphur to the important NUP precursor gaseous sulphuric acid. We also find that appreciable amounts of di-carboxylic acids survive the passage of the ATS or are even formed by the ATS. Our measurements indicate that gaseous sulphuric acid drives new NUP formation by nucleation and that gaseous di-carboxylic acids have an important role in NUP growth by condensation. Since the ATS increases OH and NO2 formation, it may also promote the formation of highly carcinogenic hydroxyl and nitro groups containing polycylic aromatic hydrocarbons. If so, these will also condense on NUP. Hence, NUP may serve as very efficient carriers transporting carcinogenic species into the deepest compartment of the human lung. Due to their small mass, NUP are not considered by present air quality regulations, which are particle mass, rather than particle number and particle surface oriented. Considering their high lung intrusion efficiency, large number, and large surface, NUP deserve increased future attention.

Production of oxalic acid from sugar beet molasses by formed nitrogen oxides.

PubMed

Gürü, M; Bilgesü, A Y; Pamuk, V

2001-03-01

Production of oxalic acid from sugar beet molasses was developed in a series of three reactors. Nitrogen oxides formed were used to manufacture oxalic acid in the second and third reactor. Parameters affecting the reaction were determined to be, air flow rate, temperature, the amount of V2O5 catalyst and the concentrations of molasses and H2SO4. The maximum yields in the second and third reactors were 78.9% and 74.6% of theoretical yield, respectively. Also, kinetic experiments were performed and the first-order rate constants were determined for the glucose consumption rate. Nitrogen oxides in off-gases from the final reactor were absorbed in water and concentrated sulphuric acid and reused in the following reactors giving slightly lower yields under similar conditions. In this novel way, it was possible to recover NO(x) and to prevent air pollution. Meanwhile, it was possible to reduce the unit cost of reactant for oxalic acid production. A maximum 77.5% and 74.1% of theoretical yield was obtained by using the absorption solutions with NO(x).

Energy efficient room temperature synthesis of cardanol-based novolac resin using acoustic cavitation.

PubMed

Jadhav, Nilesh L; Sastry, Sai Krishna C; Pinjari, Dipak V

2018-04-01

The present study deals with synthesis of cardanol-cased novolac (CBN) resin by the condensation reaction between cardanol and formaldehyde using acoustic cavitation. It is a step-growth polymerization which occurs in the presence of an acid catalyst such as adipic acid, citric acid, oxalic acid, sulphuric acid and hydrochloric acid. CBN was also synthesised by a conventional method for the sake of comparison of techniques. The effect of molar ratio, effect of catalyst, effect of different catalyst and effect of power on the conversion to CBN has been studied. The synthesised CBN was characterized using the Fourier Transform Infra Red Spectroscopy (FTIR), Gel Permeation Chromatography (GPC), Nuclear Magnetic Resonance (NMR) Spectroscopy and Thermogravimetric Analysis (TGA). The reaction was monitored by the Acid value, free formaldehyde content and viscosity of the synthesised product. The reaction time required for the conventionally synthesised CBN was 5 h (300 min) with 120 °C as an operating temperature while sonochemically the time reduced to 30 min at room temperature. The amount of time and energy saved can be quantified. Ultrasound facilitated synthesis was found to be an energy efficient and time-saving method for the synthesis of novolac resin. Copyright © 2017 Elsevier B.V. All rights reserved.

Value added liquid products from waste biomass pyrolysis using pretreatments.

PubMed

Das, Oisik; Sarmah, Ajit K

2015-12-15

Douglas fir wood, a forestry waste, was attempted to be converted into value added products by pretreatments followed by pyrolysis. Four different types of pretreatments were employed, namely, hot water treatment, torrefaction, sulphuric acid and ammonium phosphate doping. Subsequently, pyrolysis was done at 500°C and the resulting bio-oils were analysed for their chemical composition using Karl Fischer titration, thermogravimetry, ion exchange, and gas chromatography. Pretreatment with acid resulted in the highest yield of bio-oil (~60%). The acid and salt pretreatments were responsible for drastic reduction in the lignin oligomers and enhancement of water content in the pyrolytic liquid. The quantity of xylose/mannose reduced as a result of pretreatments. Although, the content of fermentable sugars remained similar across all the pretreatments, the yield of levoglucosan increased. Pretreatment of the biomass with acid yielded the highest amount of levoglucosan in the bio-oil (13.21%). The acid and salt pretreatments also elevated the amount of acetic acid in the bio-oils. Addition of acid and salt to the biomass altered the interaction of cellulose-lignin in the pyrolysis regime. Application of pretreatments should be based on the intended end use of the liquid product having a desired chemical composition. Copyright © 2015 Elsevier B.V. All rights reserved.

Nano-particulate Aluminium Nitride/Al: An Efficient and Versatile Heterogeneous Catalyst for the Synthesis of Biginelli Scaffolds

NASA Astrophysics Data System (ADS)

Tekale, S. U.; Tekale, A. B.; Kanhe, N. S.; Bhoraskar, S. V.; Pawar, R. P.

2011-12-01

Nano-particulate aluminium nitride/Al (7:1) is reported as a new heterogeneous solid acid catalyst for the synthesis of 3, 4-dihydroxypyrimidi-2-(1H)-ones and their sulphur analogues using the Biginelli reaction. This method involves short reaction time, easy separation, high yields and purity of products.

Drumstick tree (Moringa oleifera) leaves as a source of dietary selenium, sulphur, and pro-vitamin A

USDA-ARS?s Scientific Manuscript database

The “drumstick tree” or “miracle tree” (Moringa oleifera) is well known for its high nutritional value. It grows well in tropical and sub-tropical regions, even on poor soils, is drought tolerant and produces abundant leaves high in protein (with a favorable amino acid balance), vitamins, minerals, ...

COMPARISON OF DATA FROM SYNTHETIC LEACHATE AND DIRECT SAMPLING OF ACID DRAINAGE FROM MINE WASTES: IMPLICATIONS FOR MERCURY TRANSPORT AND WASTE MANAGEMENT

EPA Science Inventory

The Sulphur Bank Mercury Mine (SBMM) in Lake County, California operated from the 1860s through the 1950's. Mining for sulfur started with surface operations and progressed to shaft, then open pit techniques to obtain mercury. Mining has resulted in deposition of approximately ...

The wash-out of emissions from the atmosphere by precipitation

Treesearch

Ladislav Hanu& #154; ka; Eva Nov& #225; kov& #225; ; Nov& #225; kov& #225; Eva NO-VALUE

1976-01-01

We investigated the mechanism and dynamics of solid particles, emissions, and the concentrations of sulphur dioxide as integral components of the contamination of atmosphere. The only way of decontamination is the wash-out by precipitation (solid - snow, liquid - rain). We started from the items of information acquired during the studies of snow acidity in mountain...

Structural and physico-chemical properties of insoluble rice bran fiber: effect of acid–base induced modifications

USDA-ARS?s Scientific Manuscript database

The structural modifications of insoluble rice bran fiber (IRBF) by sequential regimes of sulphuric acid (H2SO4) and their effects on the physicochemical attributes were studied. The increment of H2SO4 concentration resulted in decreased water holding capacity that ultimately enhanced the oil bindin...

Effects of granulation on organic acid metabolism and its relation to mineral elements in Citrus grandis juice sacs.

PubMed

Wang, Xian-You; Wang, Ping; Qi, Yi-Ping; Zhou, Chen-Ping; Yang, Lin-Tong; Liao, Xin-Yan; Wang, Liu-Qing; Zhu, Dong-Huang; Chen, Li-Song

2014-02-15

We investigated the effects of granulation on organic acid metabolism and its relation to mineral elements in 'Guanximiyou' pummelo (Citrus grandis) juice sacs. Granulated juice sacs had decreased concentrations of citrate and isocitrate, thus lowering juice sac acidity. By contrast, malate concentration was higher in granulated juice sacs than in normal ones. The reduction in citrate concentration might be caused by increased degradation, as indicated by enhanced aconitase activity, whilst the increase in malate concentration might be caused by increased biosynthesis, as indicated by enhanced phosphoenolpyruvate carboxylase (PEPC). Real time quantitative reverse transcription PCR (qRT-PCR) analysis showed that the activities of most acid-metabolizing enzymes were regulated at the transcriptional level, whilst post-translational modifications might influence the PEPC activity. Granulation led to increased accumulation of mineral elements (especially phosphorus, magnesium, sulphur, zinc and copper) in juice sacs, which might be involved in the incidence of granulation in pummelo fruits. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of ultrasound on the dissolution of copper from copper converter slag by acid leaching.

PubMed

Beşe, Ayşe Vildan

2007-09-01

This work presents the optimum conditions of dissolution of copper in copper converter slag in sulphuric acid ferric sulphate mixtures in the presence and absence of ultrasound. The Taguchi method was used to determine the optimum conditions. The parameters investigated were the reaction temperature, acid concentration, ferric sulphate concentration and reaction time. The optimum conditions for the maximum dissolution of copper were determined as follows: reaction temperature, 65 degrees C; acid concentration, 0.2M; ferric sulphate concentration, 0.15M; reaction time 180 min. Under these conditions, extraction efficiency of copper, zinc, cobalt, and iron from slag were 89.28%, 51.32%, 69.87%, and 13.73%, respectively, in the presence of ultrasound, while they are 80.41%, 48.28%, 64.52%, and 12.16%, respectively, in the absence of ultrasound. As seen from the above results, it is clear that ultrasound enhances on the dissolution of Cu, Zn, Co and Fe in the slag.

Methionine peptide formation under primordial earth conditions.

PubMed

Li, Feng; Fitz, Daniel; Fraser, Donald G; Rode, Bernd M

2008-01-01

According to recent research on the origin of life it seems more and more likely that amino acids and peptides were among the first biomolecules formed on earth and that a peptide/protein world was thus a key starting point in evolution towards life. Salt-induced Peptide Formation (SIPF) has repeatedly been shown to be the most universal and plausible peptide-forming reaction currently known under prebiotic conditions and forms peptides from amino acids with the help of copper ions and sodium chloride. In this paper we present experimental results for salt-induced peptide formation from methionine. This is the first time that a sulphur-containing amino acid was investigated in this reaction. The possible catalytic effects of glycine and L-histidine in this reaction were also investigated and a possible distinction between the L- and D-forms of methionine was studied as well.

Multi-residue analysis of 26 organochlorine pesticides in Alpinia oxyphylla by GC-ECD after solid phase extraction and acid cleanup.

PubMed

Zhao, Xiangsheng; Zhou, Yakui; Kong, Weijun; Gong, Bao; Chen, Deli; Wei, Jianhe; Yang, Meihua

2016-04-01

A simple and effective multi-residue method was developed and validated for the analysis of 26 organochlorine pesticide residues in Alpinia oxyphylla by a gas chromatography with an electron capture detector (GC-ECD). The target pesticides were extracted by sonication and cleaned up with florisil solid phase extraction and sulphuric acid. Some crucial parameters, including extraction solvent and time, sorbent type, elute solvent and concentration of sulphuric acid were optimized to improve the performance of sample preparation procedure. The optimized method gave high sensitivity with detection limit ranging from 0.1 to 2.0μg/kg. Matrix-matched calibration was employed for the quantification, and a wide linear range (from 1.0 to 1000μg/kg) with r(2) values ranging from 0.9971 to 0.9998 was obtained. For the majority of the tested pesticides, the average recoveries were in acceptable range (between 70% and 110%) with relative standard deviation values below 15.0%. Matrix effect was evaluated for target compounds through the study of ratio of peak area obtained in the solvent and blank matrix. The proposed method was applied to simultaneously analyze 26 pesticides in 55 batches of Alpinia oxyphylla samples. 3 samples were found to be positive with four pesticides (α-BHC, quintozene, trans-chlordane and op'-DDD), which were confirmed by gas chromatography-mass spectrometry (GC-MS) in selective ion monitoring (SIM) mode. Copyright © 2016 Elsevier B.V. All rights reserved.

Washing as a remediation technology applicable in soils heavily polluted by mining-metallurgical activities.

PubMed

Moutsatsou, A; Gregou, M; Matsas, D; Protonotarios, V

2006-06-01

A permanent solution in order to remediate a heavily contaminated soil is washing it utilizing the appropriate reagents. The study presented in this paper deals with the washing of a soil highly polluted by mining and metallurgical activities. Pollution consists of slags, sulphur compound waste and various low grade lead condensates, all rich in heavy metals and metalloids (Pb, As, Cu, Zn, Mn and Fe). Soil was washed with deionized water, 6, 3, 2 and 1 M HCl, 6 M H(2)SO(4), 6 M HNO(3) and 0.1 M Na(2)EDTA. High extraction efficiency was achieved with respect to hydrochloric acid even at the lowest concentration; the solubility of pollutants in nitric acid was low, while sulphuric acid was proven to be problematic with respect to lead. Mobilization of metals and metalloids under DI water effect was minimal indicating that the elements fraction that is weakly bound to soil particles is insignificant. Furthermore, a kinetic study was undertaken, utilizing 1 M HCl and 0.1 M Na(2)EDTA. Results illustrated that 1 M HCl was more effective for intermediate mixing times (up to 4 h) while 0.1 M Na(2)EDTA was better applicable to short mixing times (<1 h) and low pH values (pH < 7.1). 1 M HCl was proven to be very effective for the removal of pollutants from contaminated soil but the high metal content of the resulting solution necessitates further treatment for the retention of metals.

City sewer collectors biocorrosion

NASA Astrophysics Data System (ADS)

Ksiażek, Mariusz

2014-12-01

This paper presents the biocorrosion of city sewer collectors impregnated with special polymer sulphur binders, polymerized sulphur, which is applied as the industrial waste material. The city sewer collectors are settled with a colony of soil bacteria which have corrosive effects on its structure. Chemoautotrophic nitrifying bacteria utilize the residues of halites (carbamide) which migrate in the city sewer collectors, due to the damaged dampproofing of the roadway and produce nitrogen salts. Chemoorganotrophic bacteria utilize the traces of organic substrates and produce a number of organic acids (formic, acetic, propionic, citric, oxalic and other). The activity of microorganisms so enables the origination of primary and secondary salts which affect physical properties of concretes in city sewer collectors unfavourably.

Morphology and evolution of sulphuric acid caves in South Italy

NASA Astrophysics Data System (ADS)

D'Angeli, Ilenia M.; De Waele, Jo; Galdenzi, Sandro; Madonia, Giuliana; Parise, Mario; Vattano, Marco

2016-04-01

Sulphuric acid speleogenesis (SAS) related to the upwelling of acid water enriched in H2S and CO2 represents an unusual way of cave development. Since meteoric infiltration waters are not necessarily involved in speleogenesis, caves can form without the typical associated karst expressions (i.e. dolines) at the surface. The main mechanism of sulphuric acid dissolution is the oxidation of H2S (Jones et al., 2015) which can be amplified by bacterial mediation (Engel et al., 2004). In these conditions, carbonate dissolution associated with gypsum replacement, is generally believed to be faster than the normal epigenic one (De Waele et al., 2016). In Italy several SAS caves have been identified, but only few systems have been studied in detail: Frasassi and Acquasanta Terme (Marche)(Galdenzi et al., 2010), Monte Cucco (Umbria) (Galdenzi & Menichetti, 1995), and Montecchio (Tuscany) (Piccini et al., 2015). Other preliminary studies have been carried out in Calabria (Galdenzi, 2007) and Sicily (De Waele et al., 2016). Several less studied SAS cave systems located in South Italy, and in particular in Apulia (Santa Cesarea Terme), Sicily (Acqua Fitusa, Acqua Mintina) and Calabria (Mt. Sellaro and Cassano allo Ionio) have been selected in the framework of a PhD thesis on SAS caves and their speleogenesis. Using both limestone tablet weight loss (Galdenzi et al., 2012) and micro erosion meter (MEM) (Furlani et al., 2010) methods the dissolution rate above and under water in the caves will be quantified. Geomorphological observations, landscape analysis using GIS tools, and the analysis of gypsum and other secondary minerals (alunite and jarosite) (stable isotopes and dating) will help to reconstruct the speleogenetic stages of cave formation. Preliminary microbiological analysis will determine the microbial diversity and ecology in the biofilms. References Engel S.A., Stern L.A., Bennett P.C., 2004 - Microbial contributions to cave formation: New insight into sulfuric acid speleogenesis. Geology, 32: 369-372. De Waele J., Audra P., Madonia G., Vattano M., Plan L., D'Angeli I.M., Bigot J.-Y., Nobécourt J.-C., 2016 - Sulfuric acid speleogenesis (SAS) close to the water table: examples from southern France, Austria, and Sicily. Geomorphology, 253: 452-467. Furlani S., Cucchi F., Odorico R., 2010 - A new method to study micro-topographical changes in the intertidal zone: one year of TMEM measurements on a limestone removable slab (RRS). Z. Geomorph., 54(2): 137-151. Galdenzi S., 1997 - Initial geological observations in caves bordering the Sibari plain (southern Italy). J. Cave Karst Stud., 59: 81-86. Galdenzi S., 2012 - Corrosion of limestone tablets in sulfidic ground-water: measurements and speleogenetic implications. Int. J. Spel., 41(2): 149-159. Galdenzi S., Menichetti M., 1995 - Occurrence of hypogenic caves in a karst region: examples from central Italy. Environmental Geology, 26: 39-47. Galdenzi S., Cocchioni F., Filipponi G., Selvaggio R., Scuri S., Morichetti L., Cocchioni M., 2010 - The sulfidic thermal caves of Acquasanta Terme (central Italy). J. Cave Karst Stud. 72(1): 43-58. Jones, D.S., Polerecky, L., Galdenzi, S., Dempsey, B.A., Macalady, J.L., 2015 - Fate of sulfide in the Frasassi cave system and implications for sulfuric acid speleogenesis. Chemical Geology, 410: 21-27.

Steam reforming of commercial ultra-low sulphur diesel

NASA Astrophysics Data System (ADS)

Boon, Jurriaan; van Dijk, Eric; de Munck, Sander; van den Brink, Ruud

Two main routes for small-scale diesel steam reforming exist: low-temperature pre-reforming followed by well-established methane steam reforming on the one hand and direct steam reforming on the other hand. Tests with commercial catalysts and commercially obtained diesel fuels are presented for both processes. The fuels contained up to 6.5 ppmw sulphur and up to 4.5 vol.% of biomass-derived fatty acid methyl ester (FAME). Pre-reforming sulphur-free diesel at around 475 °C has been tested with a commercial nickel catalyst for 118 h without observing catalyst deactivation, at steam-to-carbon ratios as low as 2.6. Direct steam reforming at temperatures up to 800 °C has been tested with a commercial precious metal catalyst for a total of 1190 h with two catalyst batches at steam-to-carbon ratios as low as 2.5. Deactivation was neither observed with lower steam-to-carbon ratios nor for increasing sulphur concentration. The importance of good fuel evaporation and mixing for correct testing of catalysts is illustrated. Diesel containing biodiesel components resulted in poor spray quality, hence poor mixing and evaporation upstream, eventually causing decreasing catalyst performance. The feasibility of direct high temperature steam reforming of commercial low-sulphur diesel has been demonstrated.

Agrobacterium tumefaciens can obtain sulphur from an opine that is synthesized by octopine synthase using S-methylmethionine as a substrate.

PubMed

Flores-Mireles, Ana Lidia; Eberhard, Anatol; Winans, Stephen C

2012-06-01

Agrobacterium tumefaciens incites plant tumours that produce nutrients called opines, which are utilized by the bacteria during host colonization. Various opines provide sources of carbon, nitrogen and phosphorous, but virtually nothing was previously known about how A. tumefaciens acquires sulphur during colonization. Some strains encode an operon required for the catabolism of the opine octopine. This operon contains a gene, msh, that is predicted to direct the conversion of S-methylmethionine (SMM) and homocysteine (HCys) to two equivalents of methionine. Purified Msh carried out this reaction, suggesting that SMM could be an intermediate in opine catabolism. Purified octopine synthase (Ocs, normally expressed in plant tumours) utilized SMM and pyruvate to produce a novel opine, designated sulfonopine, whose catabolism by the bacteria would regenerate SMM. Sulfonopine was produced by tobacco and Arabidopsis when colonized by A. tumefaciens and was utilized as sole source of sulphur by A. tumefaciens. Purified Ocs also used 13 other proteogenic and non-proteogenic amino acids as substrates, including three that contain sulphur. Sulfonopine and 11 other opines were tested for induction of octopine catabolic operon and all were able to do so. This is the first study of the acquisition of sulphur, an essential element, by this pathogen. © 2012 Blackwell Publishing Ltd.

Agronomic effectiveness of biofertilizers with phosphate rock, sulphur and Acidithiobacillus for yam bean grown on a Brazilian tableland acidic soil.

PubMed

Stamford, N P; Santos, P R; Santos, C E S; Freitas, A D S; Dias, S H L; Lira, M A

2007-04-01

Phosphate rocks have low available P and soluble P fertilizers have been preferably used in plant crop production, although economic and effective P sources are needed. Experiments were carried out on a Brazilian Typic Fragiudult soil with low available P to evaluate the agronomic effectiveness of phosphate rock (PR) compared with soluble phosphate fertilizer. Yam bean (Pachyrhizus erosus) inoculated with rhizobia (strains NFB 747 and NFB 748) or not inoculated was the test crop. Biofertilizers were produced in field furrows by mixing phosphate rock (PR) and sulphur inoculated with Acidithiobacillus (S+Ac) in different rates (50, 100, 150 and 200 g S kg(-1) PR), with 60 days of incubation. Treatments were carried out with PR; biofertilizers B(50), B(100), B(150), B(200); triple super phosphate (TSP); B(200) without Acidithiobacillus and a control treatment without P application (P(0)). TSP and biofertilizers plus S inoculated with Acidithiobacillus increased plant growth. Soil acidity and available P increased when biofertilizers B(150) and B(200) were applied. We conclude that biofertilizers may be used as P source; however, long term use will reduce soil pH and potentially reduce crop growth.

The Different Sensitive Behaviors of a Hydrogen-Bond Acidic Polymer-Coated SAW Sensor for Chemical Warfare Agents and Their Simulants

PubMed Central

Long, Yin; Wang, Yang; Du, Xiaosong; Cheng, Luhua; Wu, Penglin; Jiang, Yadong

2015-01-01

A linear hydrogen-bond acidic (HBA) linear functionalized polymer (PLF), was deposited onto a bare surface acoustic wave (SAW) device to fabricate a chemical sensor. Real-time responses of the sensor to a series of compounds including sarin (GB), dimethyl methylphosphonate (DMMP), mustard gas (HD), chloroethyl ethyl sulphide (2-CEES), 1,5-dichloropentane (DCP) and some organic solvents were studied. The results show that the sensor is highly sensitive to GB and DMMP, and has low sensitivity to HD and DCP, as expected. However, the sensor possesses an unexpected high sensitivity toward 2-CEES. This good sensing performance can’t be solely or mainly attributed to the dipole-dipole interaction since the sensor is not sensitive to some high polarity solvents. We believe the lone pair electrons around the sulphur atom of 2-CEES provide an electron-rich site, which facilitates the formation of hydrogen bonding between PLF and 2-CEES. On the contrary, the electron cloud on the sulphur atom of the HD molecule is offset or depleted by its two neighbouring strong electron-withdrawing groups, hence, hydrogen bonding can hardly be formed. PMID:26225975

Effects of gaseous sulphuric acid on diesel exhaust nanoparticle formation and characteristics.

PubMed

Rönkkö, Topi; Lähde, Tero; Heikkilä, Juha; Pirjola, Liisa; Bauschke, Ulrike; Arnold, Frank; Schlager, Hans; Rothe, Dieter; Yli-Ojanperä, Jaakko; Keskinen, Jorma

2013-10-15

Diesel exhaust gaseous sulphuric acid (GSA) concentrations and particle size distributions, concentrations, and volatility were studied at four driving conditions with a heavy duty diesel engine equipped with oxidative exhaust after-treatment. Low sulfur fuel and lubricant oil were used in the study. The concentration of the exhaust GSA was observed to vary depending on the engine driving history and load. The GSA affected the volatile particle fraction at high engine loads; higher GSA mole fraction was followed by an increase in volatile nucleation particle concentration and size as well as increase of size of particles possessing nonvolatile core. The GSA did not affect the number of nonvolatile particles. At low and medium loads, the exhaust GSA concentration was low and any GSA driven changes in particle population were not observed. Results show that during the exhaust cooling and dilution processes, besides critical in volatile nucleation particle formation, GSA can change the characteristics of all nucleation mode particles. Results show the dual nature of the nucleation mode particles so that the nucleation mode can include simultaneously volatile and nonvolatile particles, and fulfill the previous results for the nucleation mode formation, especially related to the role of GSA in formation processes.

SYNERGISTIC EFFECT OF HALIDE IONS ON THE CORROSION INHIBITION OF MILD STEEL IN SULPHURIC ACID USING METHYL, N-METHYL ETHYL AND ETHYL SUBSTITUTED γ-2,c-6-DIPHENYL PIPERIDIN-4-ONE SEMICARBAZONES

NASA Astrophysics Data System (ADS)

Priya, V. Shanmuga; Rani, C. Uma; Velrani, S.

The synergistic effect of halide ions such as KCl, KBr and KI on the corrosion inhibition of mild steel in 1 N sulphuric acid by γ-2,c-6-diphenyl-t-3-methyl piperdin-4-ones with semicarbazone (01SC), γ-2,c-6-diphenyl-N-methyl-t-3-ethyl piperdin-4-ones with semicarbazone (02SC) and 2,6-diphenyl-t-3-ethyl piperdin-4-one with semicarbazone (03SC) has been examined by weight loss method, potentiodynamic polarization measurements and electrochemical AC impedance spectroscopy. Results show that substituted γ-2,c-6-diphenyl piperidin-4-ones with semicarbazone act as the perfect corrosion inhibitors and their inhibition efficiency increases with the addition of halide ions. The inhibitor (01SC) shows the inhibition efficiency of 78.28% (0.2mM) by using a weight loss method. The influence of I-, Br- and Cl- anions raises the inhibition efficiency of the substituted 2,6-diphenyl piperidin-4-ones with semicarbazone due to the synergistic effect. The synergistic effect of halide ions was formed in the following order: KI > KBr > KCl.

Generation of acid mine drainage around the Karaerik copper mine (Espiye, Giresun, NE Turkey): implications from the bacterial population in the Acısu effluent.

PubMed

Sağlam, Emine Selva; Akçay, Miğraç; Çolak, Dilşat Nigar; İnan Bektaş, Kadriye; Beldüz, Ali Osman

2016-09-01

The Karaerik Cu mine is a worked-out deposit with large volumes of tailings and slags which were left around the mine site without any protection. Natural feeding of these material and run-off water from the mineralised zones into the Acısu effluent causes a serious environmental degradation and creation of acid mine drainage (AMD) along its entire length. This research aims at modelling the formation of AMD with a specific attempt on the characterisation of the bacterial population in association with AMD and their role on its occurrence. Based on 16SrRNA analyses of the clones obtained from a composite water sample, the bacterial community was determined to consist of Acidithiobacillus ferrivorans, Ferrovum myxofaciens, Leptospirillum ferrooxidans and Acidithiobacillus ferrooxidans as iron-oxidising bacteria, Acidocella facilis, Acidocella aluminiidurans, Acidiphilium cryptum and Acidiphilium multivorum as iron-reducing bacteria, and Acidithiobacillus ferrivorans, Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Acidiphilium cryptum as sulphur-oxidising bacteria. This association of bacteria with varying roles was interpreted as evidence of a concomitant occurrence of sulphur and iron cycles during the generation of AMD along the Acısu effluent draining the Karaerik mine.

Extremophiles in Mineral Sulphide Heaps: Some Bacterial Responses to Variable Temperature, Acidity and Solution Composition

PubMed Central

Watling, Helen R.; Shiers, Denis W.; Collinson, David M.

2015-01-01

In heap bioleaching, acidophilic extremophiles contribute to enhanced metal extraction from mineral sulphides through the oxidation of Fe(II) and/or reduced inorganic sulphur compounds (RISC), such as elemental sulphur or mineral sulphides, or the degradation of organic compounds derived from the ore, biota or reagents used during mineral processing. The impacts of variable solution acidity and composition, as well as temperature on the three microbiological functions have been examined for up to four bacterial species found in mineral sulphide heaps. The results indicate that bacteria adapt to sufficiently high metal concentrations (Cu, Ni, Co, Zn, As) to allow them to function in mineral sulphide heaps and, by engaging alternative metabolic pathways, to extend the solution pH range over which growth is sustained. Fluctuating temperatures during start up in sulphide heaps pose the greatest threat to efficient bacterial colonisation. The large masses of ores in bioleaching heaps mean that high temperatures arising from sulphide oxidation are hard to control initially, when the sulphide content of the ore is greatest. During that period, mesophilic and moderately thermophilic bacteria are markedly reduced in both numbers and activity. PMID:27682094

Utilization of fermented soybeans paste as flavoring lamination for Turkish dry-cured meat.

PubMed

Ahhmed, Abdulatef; Özcan, Ceyda; Karaman, Safa; Öztürk, İsmet; Çam, Mustafa; Fayemi, Peter O; Kaneko, Gen; Muguruma, Michio; Sakata, Ryoichi; Yetim, Hasan

2017-05-01

The effects of utilizing fermented soybeans paste (miso) as an alternative flavor-coating material for eliminating unpleasant odor of sulphuric and sotolone compounds from cemen in commercial pastirma were investigated. Results showed that miso-pastirma (MP) and commercial pastirma (CP) had higher L* values in comparison with the fresh meat. While no pathogen was detected in all the meat samples, statistically significant stearic acid was increased (P<0.05) and also oleic and arachidic acids were observed in MP. SDS-PAGE patterns indicated that miso had higher impacts on muscle proteins than cemen suggesting that miso can generate proteins and peptides with better technological or nutritional properties. None of the sulphur containing compounds responsible for unpleasant odor was detected in MP. Limonene, 5 esters, beta-pinene and saponins in MP contributed to citrus fruit aroma with smoother, roasty flavor and delicious taste. These findings suggest that miso contain good flavoring molecules for enhancing fruity smell and quality of pastirma. Thus, laminating cured meat with miso can be used as an alternative to cemen for producing healthier pastirma with extended shelf life and better flavor. Copyright © 2016 Elsevier Ltd. All rights reserved.

Stalagmite carbon isotopes and dead carbon proportion (DCP) in a near-closed-system situation: An interplay between sulphuric and carbonic acid dissolution

NASA Astrophysics Data System (ADS)

Bajo, Petra; Borsato, Andrea; Drysdale, Russell; Hua, Quan; Frisia, Silvia; Zanchetta, Giovanni; Hellstrom, John; Woodhead, Jon

2017-08-01

In this study, the 'dead carbon proportion' (DCP) calculated from combined U-Th and radiocarbon analyses was used to explore the carbon isotope systematics in Corchia Cave (Italy) speleothems, using the example of stalagmite CC26 which grew during the last ∼12 ka. The DCP values in CC26 are among the highest ever recorded in a stalagmite, spanning the range 44.8-68.8%. A combination of almost closed-system conditions and sulphuric acid dissolution (SAD) are proposed as major drivers in producing such a high DCP with minor contribution from old organic matter from the deep vadose zone. The long-term decrease in both DCP and δ13C most likely reflects post-glacial soil recovery above the cave, with a progressive increase of soil CO2 contribution to the total dissolved inorganic carbon (DIC). Pronounced millennial-scale shifts in DCP and relatively small coeval but antipathetic changes in δ13C are modulated by the effects of hydrological variability on open and closed-system dissolution, SAD and prior calcite precipitation. Hence, the DCP in Corchia Cave speleothems represents an additional proxy for rainfall amount.

Phytochemical Profiles and Antimicrobial Activities of Allium cepa Red cv. and A. sativum Subjected to Different Drying Methods: A Comparative MS-Based Metabolomics.

PubMed

Farag, Mohamed A; Ali, Sara E; Hodaya, Rashad H; El-Seedi, Hesham R; Sultani, Haider N; Laub, Annegret; Eissa, Tarek F; Abou-Zaid, Fouad O F; Wessjohann, Ludger A

2017-05-08

Plants of the Allium genus produce sulphur compounds that give them a characteristic (alliaceous) flavour and mediate for their medicinal use. In this study, the chemical composition and antimicrobial properties of Allium cepa red cv. and A. sativum in the context of three different drying processes were assessed using metabolomics. Bulbs were dried using either microwave, air drying, or freeze drying and further subjected to chemical analysis of their composition of volatile and non-volatile metabolites. Volatiles were collected using solid phase micro-extraction (SPME) coupled to gas chromatography-mass spectrometry (GC/MS) with 42 identified volatiles including 30 sulphur compounds, four nitriles, three aromatics, and three esters. Profiling of the polar non-volatile metabolites via ultra-performance liquid chromatography coupled to high resolution MS (UPLC/MS) annotated 51 metabolites including dipeptides, flavonoids, phenolic acids, and fatty acids. Major peaks in GC/MS or UPLC/MS contributing to the discrimination between A. sativum and A. cepa red cv. were assigned to sulphur compounds and flavonoids. Whereas sulphur conjugates amounted to the major forms in A. sativum , flavonoids predominated in the chemical composition of A. cepa red cv. With regard to drying impact on Allium metabolites, notable and clear separations among specimens were revealed using principal component analysis (PCA). The PCA scores plot of the UPLC/MS dataset showed closer metabolite composition of microwave dried specimens to freeze dried ones, and distant from air dried bulbs, observed in both A. cepa and A. sativum . Compared to GC/MS, the UPLC/MS derived PCA model was more consistent and better in assessing the impact of drying on Allium metabolism. A phthalate derivative was found exclusively in a commercial garlic preparation via GC/MS, of yet unknown origin. The freeze dried samples of both Allium species exhibited stronger antimicrobial activities compared to dried specimens with A. sativum being in general more active than A. cepa red cv.

[Chemical and nutrition evaluation of whole sorghum flour (Sorghum bicolor, L. Moench), complementation with bean and milk whey, application in baking].

PubMed

Zaparrart, M I; Salgado, J M

1994-09-01

The chemical characteristics nutritive value and technological properties of the whole sorghum flour for consumption were studied. The chemical analyses indicated 11.5% of protein, 2.7% of fat, 1.3% of fiber and 72% of carbohydrate. Major mineral in the flour were sulphur 0.25%, phosphorus 0.21%, potassium 0.15%, magnesium 0.07% and calcium 0.03%. The amino acid analyses showed lysine as the first limiting amino acid (score 31.3%) and as the second treonine (score 61.5%). The essential fatty acid contents in the oil were linolenic acid 36.2%, linolenic acid 1.4% and trace of arachidonic acid. The tanin content was 0.04%. PER and CEA were increased when the whole sorghum flour was supplemented with exception of digestibility. It was concluded that whole sorghum flour is a good source of calories in the diet (359 Cal/100g) and the protein responded positively to complementing with Phaseoulus vulgaris flour, dried milk whey and synthetic lysine. The bread baked with 0, 5, 10 and 15% of composite flour (wheat-sorghum) showed good volume, good external and internal characteristics and a high percentage of acceptability, by a panel of degustation testers.

The chemical composition of the egg shells of the potato cyst-nematode, Heterodera rostochiensis Woll

PubMed Central

Clarke, A. J.; Cox, Patricia M.; Shepherd, Audrey M.

1967-01-01

1. Eggs of the potato cyst-nematode (Heterodera rostochiensis Woll.) were isolated by sieving a suspension of crushed cysts. Eggs were broken open by ultrasonic vibration and the egg shells separated from the released larvae by centrifuging in a potassium tartrate density gradient. About 1 mg. of dried egg shells was obtained from 1000 cysts. 2. The major constituent of the egg shells was protein (59%, calculated from nitrogen content). About 80% of the egg shells went into solution on acid hydrolysis. Of the 18 amino acids determined with the Technicon Auto-Analyser, proline was most abundant and, with aspartic acid, glycine and serine, made up about 64% by weight of the total amino acids. The small amounts of aromatic and sulphur-containing amino acids, and the presence of hydroxy-proline, indicate a collagen-like protein. 3. The egg shells gave a positive van Wisselingh colour test for chitin, and glucosamine was detected in their acid hydrolysate by chromatography. The glucosamine content of the egg shells, determined by the Elson–Morgan colorimetric method, was 7%, corresponding to about 9% chitin. 4. Dried egg shells contained about 7% of lipid, 6% of carbohydrate and 3% of ash. Polyphenols (3% by weight of the egg shells) were detected in the acid hydrolysates. 5. Neither the collagen nor the chitin showed evidence of crystallinity when examined by X-ray diffraction. PMID:6069200

On the effect of the Fe(2+)/Fe(3+) redox couple on oxidation of carbon in hot H3PO4

NASA Technical Reports Server (NTRS)

Dhar, H. P.; Christner, L. G.; Kush, A. K.

1986-01-01

Oxidation studies of graphite:glassy carbon composites have been carried out at 1 and 4.7 atm. pressures in conc. H3PO4 in the presence and absence of iron ions. The concentration of the acid was varied over 85-100 wt pct, and of the iron ions over 30-300 ppm; the temperature varied over 190-210 C. Unlike the effect of Fe, which has been observed to increase the corrosion of carbon in sulphuric acid, the corrosion in phosphoric acid was observed to be slightly decreased or not at all affected. This result arises because of the catalytic reduction of the oxidized surface groups of carbon by Fe(2+) ions. The catalytic reduction is possible because under the experimental conditions the redox potential of the Fe(2+)/Fe(3+) couple is lower than the open-circuit voltage of carbon.

The effect of a lignosulphate type additive on the lead—acid battery positive plate reactions

NASA Astrophysics Data System (ADS)

Ovuru, S. E.; Harrison, J. A.

The electrochemical formation of lead dioxide has been investigated at a lead electrode in a 5 M sulphuric acid solution, and in the presence of phosphoric acid and lignosulphate-type additive. The formation of lead dioxide from lead sulphate, and the reverse reaction, have been investigated by the linear potential sweep method, by an impedance method in which the impedance was measured at the end of each pulse during a potential pulse train, and by a charging curve method in which the current and charge was measured during a similar potential pulse train. The charge measurements prove that the main effect of the additive is to decrease the accompanying oxygen evolution reaction. The impedance measurements, however, show that the additive has a small but significant effect on the structure of the solid lead sulphate and lead dioxide layers.

Chemistry Cube Game - Exploring Basic Principles of Chemistry by Turning Cubes.

PubMed

Müller, Markus T

2018-02-01

The Chemistry Cube Game invites students at secondary school level 1 and 2 to explore basic concepts of chemistry in a playful way, either as individuals or in teams. It consists of 15 different cubes, 9 cubes for different acids, their corresponding bases and precursors, and 6 cubes for different reducing and oxidising agents. The cubes can be rotated in those directions indicated. Each 'allowed' vertical or horizontal rotation of 90° stands for a chemical reaction or a physical transition. Two different games and playing modes are presented here: First, redox chemistry is introduced for the formation of salts from elementary metals and non-metals. Second, the speciation of acids and bases at different pH-values is shown. The cubes can be also used for games about environmental chemistry such as the carbon and sulphur cycle, covering the topic of acid rain, or the nitrogen cycle including ammoniac synthesis, nitrification and de-nitrification.

Combinatorics of aliphatic amino acids

NASA Astrophysics Data System (ADS)

Grützmann, Konrad; Böcker, Sebastian; Schuster, Stefan

2011-01-01

This study combines biology and mathematics, showing that a relatively simple question from molecular biology can lead to complicated mathematics. The question is how to calculate the number of theoretically possible aliphatic amino acids as a function of the number of carbon atoms in the side chain. The presented calculation is based on earlier results from theoretical chemistry concerning alkyl compounds. Mathematical properties of this number series are highlighted. We discuss which of the theoretically possible structures really occur in living organisms, such as leucine and isoleucine with a chain length of four. This is done both for a strict definition of aliphatic amino acids only involving carbon and hydrogen atoms in their side chain and for a less strict definition allowing sulphur, nitrogen and oxygen atoms. While the main focus is on proteinogenic amino acids, we also give several examples of non-proteinogenic aliphatic amino acids, playing a role, for instance, in signalling. The results are in agreement with a general phenomenon found in biology: Usually, only a small number of molecules are chosen as building blocks to assemble an inconceivable number of different macromolecules as proteins. Thus, natural biological complexity arises from the multifarious combination of building blocks.

Acetylated sialic acid residues and blood group antigens localise within the epithelium in microvillous atrophy indicating internal accumulation of the glycocalyx

PubMed Central

Phillips, A D; Brown, A; Hicks, S; Schüller, S; Murch, S H; Walker-Smith, J A; Swallow, D M

2004-01-01

Background: Microvillous atrophy, a disorder of intractable diarrhoea in infancy, is characterised by the intestinal epithelial cell abnormalities of abnormal accumulation of periodic acid-Schiff (PAS) positive secretory granules within the apical cytoplasm and the presence of microvillous inclusions. The identity of the PAS positive material is not known, and the aim of this paper was to further investigate its composition. Methods: Formaldehyde fixed sections were stained with alcian blue/PAS to identify the acidic or neutral nature of the material, phenylhydrazine blocking was employed to stain specifically for sialic acid, and saponification determined the presence of sialic acid acetylation. The specificity of sialic acid staining was tested by digestion with mild sulphuric acid. Expression of blood group related antigens was tested immunochemically. Results: Alcian blue/PAS staining identified a closely apposed layer of acidic material on the otherwise neutral (PAS positive) brush border in controls. In microvillous atrophy, a triple layer was seen with an outer acidic layer, an unstained brush border region, and accumulation within the epithelium of a neutral glycosubstance that contained acetylated sialic acid. Blood group antigens were detected on the brush border, in mucus, and within goblet cells in controls. In microvillous atrophy they were additionally expressed within the apical cytoplasm of epithelial cells mirroring the PAS abnormality. Immuno electron microscopy localised expression to secretory granules. Conclusions: A neutral, blood group antigen positive, glycosubstance that contains acetylated sialic acid accumulates in the epithelium in microvillous atrophy. Previous studies have demonstrated that the direct and indirect constitutive pathways are intact in this disorder and it is speculated that the abnormal staining pattern reflects accumulation of glycocalyx related material. PMID:15542511

The content of protein and of amino acids in Jerusalem artichoke tubers (Helianthus tuberosus L.) of red variety Rote Zonenkugel.

PubMed

Cieślik, Ewa; Gębusia, Agnieszka; Florkiewicz, Adam; Mickowska, Barbara

2011-01-01

Jerusalem artichoke (Helianthus tuberosus L.) is grown primarily for its edible tubers, which were first cultivated by native Americans before the arrival of the Europeans. Unlike most tubers, but in common with other members of the Asteraceae, the tubers store fructans instead of starch. Fructans are non-digestible carbohydrates considered functional food ingredients because they affect body processes in ways that result in better health and in many diseases prevention. However, the Jerusalem artichoke deserves attention not only because of the content of fructans, recent studies also indicate a high protein content, including essential amino acids. The aim of the work was to establish the content of protein and amino acids in Jerusalem artichoke tubers (Helianthus tuberosus L.) of red variety--Rote Zonenkugel. The content of protein was estimated by Dumas method. The amino acids composition was analysed with ion-change chromatography with postcolumn derivatisation and detection of ninhydryn reaction with automatic amino acids analyser. The assessed liophylisate was characterised by high protein content (6.36%) in comparison to chicory (which is the main industrial source of fructans) and to commonly consumed potatoes. There was shown a few times higher content of essential amino acids (also of methionine) in comparison to chicory and potato. The examined essential amino acids were present in very advantagenous proportions. In Jerusalem artichoke tubers of Rote Zonenkugel variety of the high content of protein was established in comparison to other plant sources. The high content was found of amino acids with special stress on essential amino acids (esp. sulphur ones).

Environmentally friendly microwave-assisted sequential extraction method followed by ICP-OES and ion-chromatographic analysis for rapid determination of sulphur forms in coal samples.

PubMed

Mketo, Nomvano; Nomngongo, Philiswa N; Ngila, J Catherine

2018-05-15

A rapid three-step sequential extraction method was developed under microwave radiation followed by inductively coupled plasma-optical emission spectroscopic (ICP-OES) and ion-chromatographic (IC) analysis for the determination of sulphur forms in coal samples. The experimental conditions of the proposed microwave-assisted sequential extraction (MW-ASE) procedure were optimized by using multivariate mathematical tools. Pareto charts generated from 2 3 full factorial design showed that, extraction time has insignificant effect on the extraction of sulphur species, therefore, all the sequential extraction steps were performed for 5 min. The optimum values according to the central composite designs and counter plots of the response surface methodology were 200 °C (microwave temperature) and 0.1 g (coal amount) for all the investigated extracting reagents (H 2 O, HCl and HNO 3 ). When the optimum conditions of the proposed MW-ASE procedure were applied in coal CRMs, SARM 18 showed more organic sulphur (72%) and the other two coal CRMs (SARMs 19 and 20) were dominated by sulphide sulphur species (52-58%). The sum of the sulphur forms from the sequential extraction steps have shown consistent agreement (95-96%) with certified total sulphur values on the coal CRM certificates. This correlation, in addition to the good precision (1.7%) achieved by the proposed procedure, suggests that the sequential extraction method is reliable, accurate and reproducible. To safe-guard the destruction of pyritic and organic sulphur forms in extraction step 1, water was used instead of HCl. Additionally, the notorious acidic mixture (HCl/HNO 3 /HF) was replaced by greener reagent (H 2 O 2 ) in the last extraction step. Therefore, the proposed MW-ASE method can be applied in routine laboratories for the determination of sulphur forms in coal and coal related matrices. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of sulphur concentration on bioleaching of heavy metals from contaminated dredged sediments.

PubMed

Fang, D; Zhao, L; Yang, Z Q; Shan, H X; Gao, Y; Yang, Q

2009-11-01

The sulphur-based bioleaching process using sulphur-oxidizing bacteria (SOB) has been demonstrated to be a feasible technology for removing heavy metals from contaminated sediments, but the excess sulphur application will lead to the re-acidification of bioleached sediments. The objective of the present study was to examine the effect of sulphur concentration on the bioleaching of heavy metals from contaminated sediments, with the ultimate purpose of minimizing the sulphur addition. The results showed that the inoculation of 7% of indigenous SOB, containing 3.6 x 10(8) colony forming units (CFU) mL(-1), and addition of elemental sulphur as a substrate (0.5 to 7.0 g L(-1)) resulted in a sharp decrease in sediment pH from an initial pH 8.0 to pH 1.4-2.4 and an increase in ORP (oxidation-reduction potential) from -10 mV to 500 mV within 10 days of bioleaching. Although the increase in sulphur concentration enhanced the rates of pH reduction and ORP elevation, the bioleaching process with the addition of 3.0 g L(-1) of sulphur was already sufficient to reach conditions of acidity (pH < 2.0) and ORP (500 mV) necessary for a satisfactory removal of metals, and, at day 10, 71.8% of Cu, 58.2% of Zn, and 25.3% of Cr were removed from the sediments. During the bioleaching process, Zn removal increased with a reduction in pH, whereas the removal of Cu and Cr increased not only with a reduction in pH but also with an increase in ORP. Results of sequential selective extraction indicated that the final levels of metal removals were dependent on their speciation distribution in the original sediments, and after bioleaching those unremoved metals in the bioleached sediments mainly existed in the residual fraction.

Isolation and fractionation of soil humin using alkaline urea and dimethylsulphoxide plus sulphuric acid

NASA Astrophysics Data System (ADS)

Song, Guixue; Hayes, Michael H. B.; Novotny, Etelvino H.; Simpson, Andre J.

2011-01-01

Humin, the most recalcitrant and abundant organic fraction of soils and of sediments, is a significant contributor to the stable carbon pool in soils and is important for the global carbon budget. It has significant resistance to transformations by microorganisms. Based on the classical operational definition, humin can include any humic-type substance that is not soluble in water at any pH. We demonstrate in this study how sequential exhaustive extractions with 0.1 M sodium hydroxide (NaOH) + 6 M urea, followed by dimethylsulphoxide (DMSO) + 6% ( v/ v) sulphuric acid (H2SO4) solvent systems, can extract 70-80% of the residual materials remaining after prior exhaustive extractions in neutral and aqueous basic media. Solid-state 13C NMR spectra have shown that the components isolated in the base + urea system were compositionally similar to the humic and fulvic acid fractions isolated at pH 12.6 in the aqueous media. The NMR spectra indicated that the major components isolated in the DMSO + H2SO4 medium had aliphatic hydrocarbon associated with carboxyl functionalities and with lesser amounts of carbohydrate and peptide and minor amounts of lignin-derived components. The major components will have significant contributions from long-chain fatty acids, waxes, to cuticular materials. The isolates in the DMSO + H2SO4 medium were compositionally similar to the organic components that resisted solvation and remained associated with the soil clays. It is concluded that the base + urea system released humic and fulvic acids held by hydrogen bonding or by entrapment within the humin matrix. The recalcitrant humin materials extracted in DMSO + H2SO4 are largely biological molecules (from plants and the soil microbial population) that are likely to be protected from degradation by their hydrophobic moieties and by sorption on the soil clays. Thus, the major components of humin do not satisfy the classical definitions for humic substances which emphasise that these arise from microbial or chemical transformations in soils of the components of organic debris.

Recovery of yttrium from fluorescent powder of cathode ray tube, CRT: Zn removal by sulphide precipitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Innocenzi, Valentina, E-mail: valentina.innocenzi1@univaq.it; De Michelis, Ida; Ferella, Francesco

2013-11-15

Highlights: • Treatment of fluorescent powder of CRT waste. • Factorial experimental designs to study acid leaching of fluorescent powder and the purification of leach liquors. • Recover of yttrium by precipitation using oxalic acid. • Suitable flowsheet to recover yttrium from fluorescent powder. - Abstract: This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2{sup 2} full factorial plan and the highest extraction yields for yttrium and zinc equalmore » to 100% are observed under the following conditions: 3 M of sulphuric acid, 10% v/v of H{sub 2}O{sub 2} concentrated solution at 30% v/v, 10% w/w pulp density, 70 °C and 3 h of reaction. Two series of precipitation tests for zinc are carried out: a 2{sup 2} full factorial design and a completely randomized factorial design. In these series the factors investigated are pH of solution during the precipitation and the amount of sodium sulphide added to precipitate zinc sulphide. The data of these tests are used to describe two empirical mathematical models for zinc and yttrium precipitation yields by regression analysis. The highest precipitation yields for zinc are obtained under the following conditions: pH equal to 2–2.5% and 10–12% v/v of Na{sub 2}S concentrated solution at 10% w/v. In these conditions the coprecipitation of yttrium is of 15–20%. Finally further yttrium precipitation experiments by oxalic acid on the residual solutions, after removing of zinc, show that yttrium could be recovered and calcined to obtain the final product as yttrium oxide. The achieved results allow to propose a CRT recycling process based on leaching of fluorescent powder from cathode ray tube and recovery of yttrium oxide after removing of zinc by precipitation. The final recovery of yttrium is 75–80%.« less

Determination of rhenium in molybdenite by X-ray fluorescence: A combined chemical-spectrometric technique.

PubMed

Solt, M W; Wahlberg, J S; Myers, A T

1969-01-01

Rhenium in molybdenite is separated from molybdenum by distillation of rhenium heptoxide from a perchloric-sulphuric acid mixture. It is concentrated by precipitation of the sulphide and then determined by X-ray fluorescence. From 3 to 1000 microg of rhenium can be measured with a precision generally within 2%. The procedure tolerates larger amounts of molybdenum than the usual colorimetric methods.

JPRS Report, Science & Technology, USSR: Materials Science

DTIC Science & Technology

1988-02-22

on 55 a known precision flotation method of denstiy measurement. Closed porosity- was determined by measuring the density of specimens, subsequent...for producing sulphuric acid from pyrite concentrates, which are waste of various production processes and are stored in large quantities in the...Buryat ASSR as a result of centralized processing thereof. In order to do this, one should create a territorial center for processing pyrite

’Offsets’ for NATO Procurement of the Airborne Warning and Control System: Opportunities and Implications

DTIC Science & Technology

1976-02-01

the Anglo-French ; azel ’, the German B9715, and the Italian Ag129--all appear responsi- e to a U.S. need for an Advanced Scout -32- Helicopter (ASH...currencies by OECD using IMF parity rates, or average of annual range of flexible rates. -86- code (individual chemicals, such as sulphuric acid , etc.), it is

Using secondary metabolites in the monitoring of the condition of tree stands under industrial pollution

Treesearch

L. L. Fuksman

2000-01-01

The aim of this paper is to determine tile optimal physiological indicator in diagnosing the condition of tree stands under the stress of industrial pollution. Based on experimental results of the fumigation on pine seedlings with sulphur dioxide, acid rain treatment, and the effect of heavy metals on the seedlings, it is reasonable to use the secondary substances or...

Enhanced corrosion resistance of stainless steel type 316 in sulphuric acid solution using eco-friendly waste product

NASA Astrophysics Data System (ADS)

Sanni, O.; Popoola, A. P. I.; Fayomi, O. S. I.

2018-06-01

Literature has shown that different organic compounds are effective corrosion inhibitors for metal in acidic environments. Such compounds usually contain oxygen, nitrogen or sulphur and function through adsorption on the metal surface, thereby creating a barrier for corrosion attack. Unfortunately, these organic compounds are toxic, scarce and expensive. Therefore, plants, natural product and natural oils have been posed as cheap, environmentally acceptable, abundant, readily available and effective molecules having low environmental impact. The corrosion resistance of austenitic stainless steel Type 316 in the presence of eco-friendly waste product was studied using weight loss and potentiodynamic polarization techniques in 0.5 M H2SO4. The corrosion rate and corrosion potential of the steel was significantly altered by the studied inhibitor. Results show that increase in concentration of the inhibitor hinders the formation of the passive film. Experimental observation shows that its pitting potential depends on the concentration of the inhibitor in the acid solution due to adsorption of anions at the metal film interface. The presence of egg shell powder had a strong influence on the corrosion resistance of stainless steel Type 316 with highest inhibition efficiency of 94.74% from weight loss analysis, this is as a result of electrochemical action and inhibition of the steel by the ionized molecules of the inhibiting compound which influenced the mechanism of the redox reactions responsible for corrosion and surface deterioration. Inhibitor adsorption fits the Langmuir isotherm model. The two methods employed for the corrosion assessment were in good agreement.

Occupational dental erosion from exposure to acids: a review.

PubMed

Wiegand, Annette; Attin, Thomas

2007-05-01

Dental erosion is characterized as a disorder with a multifactorial aetiology including environmental acid exposure. The purpose of this article was to summarize and discuss the available information concerning occupational dental erosion. Information from original scientific papers, case reports and reviews with additional case reports listed in PubMed, Medline or EMBASE [search term: (dental OR enamel OR dentin) AND (erosion OR tooth wear) AND (occupational OR worker)] were included in the review. References from the identified publications were manually searched to identify additional relevant articles. The systematic search resulted in 59 papers, of which 42 were suitable for the present review. Seventeen papers demonstrated evidence that battery, galvanizing and associated workers exposed to sulphuric or hydrochloric acid were at higher risk of dental erosion. For other industrial workers, wine tasters and competitive swimmers, only a few clinical studies exist and these do not allow the drawing of definitive conclusions. Occupational acid exposure might increase the risk of dental erosion. Evidence for occupational dental erosion is limited to battery and galvanizing workers, while data for other occupational groups need to be confirmed by further studies.

Synthesis and characterization of neopenthyl glycol diolete as a biolubricant base

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajaendran, Vanitah; Salimon, Jumat; Derawi, Darfizzi

2015-09-25

Neopenthyl glycol is a polyol that is potential to be a good base for biolubricant via esterification process with oleic acid. In this study, esterification reaction between NPG and oleic acid has been carried out in the presence of 2% w/w sulphuric acid (based on weight of FA) as a catalyst to produce NPG dioleate. The temperature for this reaction was 130°C and the molar ration of oleic acid: NPG was 2:1. The time for the reaction was 4 hours. The presence of the ester in the product was confirmed through Fourier Transform Infrared (FTIR) and followed by NPG dioletemore » composition determination via Gas Chromatography (GC-FID). The structure of NPG diolete was confirmed using both proton and carbon Nuclear Magnetic Resonance ({sup 1}H-NMR and {sup 13}C-NMR) analysis. 100% NPG diolete were obtained in this study. The viscosity index of the product is 227, flash point 200°C, pour point −44°C and oxidative stability 177°C.« less

Microbial sulphur isotope fractionation in a Mars analogue environment at Rio Tinto, SW Spain

NASA Astrophysics Data System (ADS)

Velasco, Esther; Mason, Paul; Gonzalez-Toril, Elena; Zegers, Tanja; Davies, Gareth; Amils, Ricardo

2010-05-01

The development of geochemical proxies for possible early life on Mars is important in preparation for future space missions, especially those that will return samples to Earth. Sulfur isotopes are likely to be a key future tool for this purpose since abundant sulphate minerals on the surface of Mars [1], such as jarosite (KFe3+3(SO4)2(OH)6), may record the activity of sulphur metabolizing microorganisms. Little is currently known about the sulphur isotope effects associated with sulphate reduction in the acidic environments where jarosite and other minerals are likely to have precipitated. Here we investigate the relationship between sulphate reducing activity and sulphur isotope fractionation in a modern hyper-acidic subareal environment at Rio Tinto, SW Spain [2,3,4]. The geochemical characteristics of Rio Tinto are the consequence of modern weathering of pyrite-rich ores in the Iberian Pyritic Belt, and the metabolism of iron and sulphur compounds by chemolithotrophic microorganisms. This results in a high concentration of ferric iron that is soluble under the acidic conditions generated by the biological activity. These conditions cause the precipitation of ferric-bearing minerals, including amorphous phases and hydronium jarosite. Sulphate reducing bacteria have recently been isolated from Rio Tinto sediments despite the fact that high concentrations of ferrous iron can inhibit microbial sulphate reduction. Flow-through reactor experiments were performed using sediment samples from Río Tinto, in localities where the potential for sulphate-reducing activity was previously identified. Sediments were taken both in the upper part of the river and in the estuary where tidal effects have created a dynamic environment, with mixing between hyperacidic and marine conditions. Sediments were incubated in the laboratory at 30oC, using an artificial input solution with sulphate in excess using techniques developed by Stam et al. [5]. Two sets of experiments were done at pH 7 and pH 3 with electron donors provided by the natural substrate. Duplicate reactors were incubated for a total of 10 weeks. Initial data indicate moderate potential sulfate reduction rates of between 5 and 45 nM cm-3 h-1 at both pH 7 and pH 3. Isotope effects will be determined by measuring differences in 34S between the sulphate in the inflow and outflow solutions. We expect our results to further help in the targeting of sampling sites in the search for traces of life on Mars. References: [1] Van Zuilen, M. (2008). Space Science Reviews 135(1-4): 221-232 [2] Amils, R., et al. (2007), Planetary and Space Science 55, 370-381. [3] Fernández-Remolar, D., et al., (2005), Earth and Planetary Science Letters 240 (2005) 149-167. [4] Mumma, M. J., et al., (2009), Science, Vol 323, pag 1041-1045. [5] Stam, M.C., et al., (2008). Geochim. Cosmochim. Acta 72: A891.

Speleothem records of acid sulphate deposition and organic carbon mobilisation

NASA Astrophysics Data System (ADS)

Wynn, Peter; Fairchild, Ian; Bourdin, Clement; Baldini, James; Muller, Wolfgang; Hartland, Adam; Bartlett, Rebecca

2017-04-01

Dramatic increases in measured surface water DOC in recent decades have been variously attributed to either temperature rise, or destabilisation of long-term soil carbon pools following sulphur peak emissions status. However, whilst both drivers of DOC dynamics are plausible, they remain difficult to test due to the restricted nature of the available records of riverine DOC flux (1978 to present), and the limited availability of SO2 emissions inventory data at the regional scale. Speleothems offer long term records of both sulphur and carbon. New techniques to extract sulphur concentrations and isotopes from speleothem calcite have enabled archives of pollution history and environmental acidification to be reconstructed. Due to the large dynamic range in sulphur isotopic values from end member sources (marine aerosol +21 ‰ to continental biogenic emissions -30 ‰) and limited environmental fractionation under oxidising conditions, sulphur isotopes form an ideal tracer of industrial pollution and environmental acidification in the palaeo-record. We couple this acidification history to the carbon record, using organic matter fluorescence and trace metals. Trace metal ratios and abundance can be used to infer the type and size of organic ligand and are therefore sensitive to changes in temperature as a driver of organic carbon processing and biodegradation. This allows fluorescent properties and ratios of trace metals in speleothem carbonate to be used to represent both the flux of organic carbon into the cave as well as the degradation pathway. Here we present some of the first results of this work, exploring sulphur acidification as a mechanistic control on carbon solubility and export throughout the twentieth century.

Surface characterization of acidic ceria-zirconia prepared by direct sulfation

NASA Astrophysics Data System (ADS)

Azambre, B.; Zenboury, L.; Weber, J. V.; Burg, P.

2010-05-01

Acidic ceria-zirconia (SCZ) solid acid catalysts with a nominal surface density of ca 2 SO 42-/nm 2 were prepared by a simple route consisting in soaking high specific surface area Ce xZr 1- xO 2 (with x = 0.21 and 0.69) mixed oxides solutions in 0.5 M sulphuric acid. Characterizations by TPD-MS, TP-DRIFTS and FT-Raman revealed that most of surface structures generated by sulfation are stable at least up to 700 °C under inert atmosphere and consist mainly as isolated sulfates located on defects or crystal planes and to a lesser extent as polysulfates. Investigations by pyridine adsorption/desorption have stated that: SCZ possess both strong Brønsted (B) and Lewis (L) acid sites, some of them being presumably superacidic; the B/L site ratio was found to be more dependent on the temperature and hydration degree than on the composition of the ceria-zirconia. By contrast, the reactivity of the parent Ce xZr 1- xO 2 materials towards pyridine is mostly driven by redox properties resulting in the formation of Py-oxide with the participation of Lewis acid sites of moderate strength ( cus Ce x+ and Zr x+ cations). Basicity studies by CO 2 adsorption/desorption reveal that SCZ surfaces are solely acidic whereas the number and strength of Lewis basic sites increases with the Ce content for the parent Ce xZr 1- xO 2 materials.

Overexpression of serine acetlytransferase produced large increases in O-acetylserine and free cysteine in developing seeds of a grain legume

PubMed Central

Tabe, Linda; Wirtz, Markus; Molvig, Lisa; Droux, Michel; Hell, Ruediger

2010-01-01

There have been many attempts to increase concentrations of the nutritionally essential sulphur amino acids by modifying their biosynthetic pathway in leaves of transgenic plants. This report describes the first modification of cysteine biosyntheis in developing seeds; those of the grain legume, narrow leaf lupin (Lupinus angustifolius, L.). Expression in developing lupin embryos of a serine acetyltransferase (SAT) from Arabidopsis thaliana (AtSAT1 or AtSerat 2;1) was associated with increases of up to 5-fold in the concentrations of O-acetylserine (OAS), the immediate product of SAT, and up to 26-fold in free cysteine, resulting in some of the highest in vivo concentrations of these metabolites yet reported. Despite the dramatic changes in free cysteine in developing embryos of SAT overexpressers, concentrations of free methionine in developing embryos, and the total cysteine and methionine concentrations in mature seeds were not significantly altered. Pooled F2 seeds segregating for the SAT transgene and for a transgene encoding a methionine- and cysteine-rich sunflower seed storage protein also had increased OAS and free cysteine, but not free methionine, during development, and no increase in mature seed total sulphur amino acids compared with controls lacking SAT overexpression. The data support the view that the cysteine biosynthetic pathway is active in developing seeds, and indicate that SAT activity limits cysteine biosynthesis, but that cysteine supply is not limiting for methionine biosynthesis or for storage protein synthesis in maturing lupin embryos in conditions of adequate sulphur nutrition. OAS and free methionine, but not free cysteine, were implicated as signalling metabolites controlling expression of a gene for a cysteine-rich seed storage protein. PMID:19939888

Overexpression of serine acetlytransferase produced large increases in O-acetylserine and free cysteine in developing seeds of a grain legume.

PubMed

Tabe, Linda; Wirtz, Markus; Molvig, Lisa; Droux, Michel; Hell, Ruediger

2010-03-01

There have been many attempts to increase concentrations of the nutritionally essential sulphur amino acids by modifying their biosynthetic pathway in leaves of transgenic plants. This report describes the first modification of cysteine biosynthesis in developing seeds; those of the grain legume, narrow leaf lupin (Lupinus angustifolius, L.). Expression in developing lupin embryos of a serine acetyltransferase (SAT) from Arabidopsis thaliana (AtSAT1 or AtSerat 2;1) was associated with increases of up to 5-fold in the concentrations of O-acetylserine (OAS), the immediate product of SAT, and up to 26-fold in free cysteine, resulting in some of the highest in vivo concentrations of these metabolites yet reported. Despite the dramatic changes in free cysteine in developing embryos of SAT overexpressers, concentrations of free methionine in developing embryos, and the total cysteine and methionine concentrations in mature seeds were not significantly altered. Pooled F(2) seeds segregating for the SAT transgene and for a transgene encoding a methionine- and cysteine-rich sunflower seed storage protein also had increased OAS and free cysteine, but not free methionine, during development, and no increase in mature seed total sulphur amino acids compared with controls lacking SAT overexpression. The data support the view that the cysteine biosynthetic pathway is active in developing seeds, and indicate that SAT activity limits cysteine biosynthesis, but that cysteine supply is not limiting for methionine biosynthesis or for storage protein synthesis in maturing lupin embryos in conditions of adequate sulphur nutrition. OAS and free methionine, but not free cysteine, were implicated as signalling metabolites controlling expression of a gene for a cysteine-rich seed storage protein.

Substoichiometric radiochemical determination of silver with potassium ethyl xanthate in photofilm washings.

PubMed

Reddy, P C; Rangamannar, B

1990-05-01

An accurate and rapid radiochemical method has been developed for the determination of microgram amount of silver employing potassium ethyl xanthate as a substoichiometric radiochemical reagent. The light yellow coloured silver ethyl xanthate formed was extracted into nitrobenzene from sulphuric acid media. The effect of foreign ions on the extraction was studied. The method was applied to the determination of silver content in photofilm washings.

Sulphur-rich volcanic eruptions and stratospheric aerosols

NASA Technical Reports Server (NTRS)

Rampino, M. R.; Self, S.

1984-01-01

Data from direct measurements of stratospheric optical depth, Greenland ice-core acidity, and volcanological studies are compared, and it is shown that relatively small but sulfur-rich volcanic eruptions can have atmospheric effects equal to or even greater than much larger sulfur-poor eruptions. These small eruptions are probably the most frequent cause of increased stratospheric aerosols. The possible sources of the excess sulfur released in these eruptions are discussed.

Determination of rhenium in molybdenite by X-ray fluorescence. A combined chemical-spectrometric technique

USGS Publications Warehouse

Solt, M.W.; Wahlberg, J.S.; Myers, A.T.

1969-01-01

Rhenium in molybdenite is separated from molybdenum by distillation of rhenium heptoxide from a perchloric-sulphuric acid mixture. It is concentrated by precipitation of the sulphide and then determined by X-ray fluorescence. From 3 to 1000 ??g of rhenium can be measured with a precision generally within 2%. The procedure tolerates larger amounts of molybdenum than the usual colorimetric methods. ?? 1969.

Diets containing leguminous seeds influence chromium content in the rat femur bone.

PubMed

Gralak, M A; Leontowicz, H; Leontowicz, M; Debski, B

2002-01-01

Leguminous seeds contain a lot of antinutritional factors (ANFs) such as protease inhibitors, lectins and condensed tannins which can affect bioavailability of nutrients. Detrimental effect of protease inhibitors can be decreased by sulphur amino acids addition. Moreover, most of the leguminous ANFs are thermolabile. Hence, legumes tested in our study were extruded and/or diets were supplemented with methionine and cystine (0.15% + 0.15%). The present experiment was performed for 28 days on 90 Wistar rats divided into nine feeding groups. Semipurified diets (10% casein) were supplemented (10%), except the control one, with soybean (S) or faba bean (F), raw (R) or extruded (E), with addition of sulphur amino acids (SAA) or without them. The Cr concentration was determined in the femur bone. Total feed intake during whole trial widely varied among the groups and was the lowest in SR (289 g) and FR (294 g) groups. There was no correlation between feed intake and Cr content in the femur bone. Generally, 10% soybean in the diet decreased Cr concentration in the bones, and faba bean increased it. The SAA addition to diets generally increased femur Cr content. However, there was a significant interaction between SAA supplementation and extrusion of faba bean, hence, the effect of their combination was unclear.

Recovery of Ni Metal from Spent Catalyst with Emulsion Liquid Membrane Using Cyanex 272 as Extractant

NASA Astrophysics Data System (ADS)

Yuliusman; Huda, M.; Ramadhan, I. T.; Farry, A. R.; Wulandari, P. T.; Alfia, R.

2018-03-01

In this study was conducted to recover nickel metal from spent nickel catalyst resulting from hydrotreating process in petroleum industry. The nickel extraction study with the emulsion liquid membrane using Cyanex 272 as an extractant to extract and separate nickel from the feed phase solution. Feed phase solution was preapred from spent catalyst using sulphuric acid. Liquid membrane consists of a kerosene as diluent, a Span 80 as surfactant, a Cyanex 272 as carrier and sulphuric acid solutions have been used as the stripping solution. The important parameters governing the permeation of nickel and their effect on the separation process have been studied. These parameters are surfactant concentration, extractant concentration feed phase pH. The optimum conditions of the emulsion membrane making process is using 0.06 M Cyanex 272, 8% w/v SPAN 80, 0.05 M H2SO4, internal phase extractant / phase volume ratio: 1/1, and stirring speed 1150 rpm for 60 Minute that can produce emulsion membrane with stability level above 90% after 4 hours. In the extraction process with optimum condition pH 6 for feed phase, ratio of phase emulsion/phase of feed: 1/2, and stirring speed 175 rpm for 15 minutes with result 81.51% nickel was extracted.

Phosphate Mines, Jordan

NASA Technical Reports Server (NTRS)

2008-01-01

Jordan's leading industry and export commodities are phosphate and potash, ranked in the top three in the world. These are used to make fertilizer. The Jordan Phosphate Mines Company is the sole producer, having started operations in 1935. In addition to mining activities, the company produces phosphoric acid (for fertilizers, detergents, pharmaceuticals), diammonium phosphate (for fertilizer), sulphuric acid (many uses), and aluminum fluoride (a catalyst to make aluminum and magnesium).

The image covers an area of 27.5 x 49.4 km, was acquired on September 17, 2005, and is located near 30.8 degrees north latitude, 36.1 degrees east longitude.

The U.S. science team is located at NASA's Jet Propulsion Laboratory, Pasadena, Calif. The Terra mission is part of NASA's Science Mission Directorate.

Environmental characterisation of coal mine waste rock in the field: an example from New Zealand

NASA Astrophysics Data System (ADS)

Hughes, J.; Craw, D.; Peake, B.; Lindsay, P.; Weber, P.

2007-08-01

Characterisation of mine waste rock with respect to acid generation potential is a necessary part of routine mine operations, so that environmentally benign waste rock stacks can be constructed for permanent storage. Standard static characterisation techniques, such as acid neutralisation capacity (ANC), maximum potential acidity, and associated acid-base accounting, require laboratory tests that can be difficult to obtain rapidly at remote mine sites. We show that a combination of paste pH and a simple portable carbonate dissolution test, both techniques that can be done in the field in a 15 min time-frame, is useful for distinguishing rocks that are potentially acid-forming from those that are acid-neutralising. Use of these techniques could allow characterisation of mine wastes at the metre scale during mine excavation operations. Our application of these techniques to pyrite-bearing (total S = 1-4 wt%) but variably calcareous coal mine overburden shows that there is a strong correlation between the portable carbonate dissolution technique and laboratory-determined ANC measurements (range of 0-10 wt% calcite equivalent). Paste pH measurements on the same rocks are bimodal, with high-sulphur, low-calcite rocks yielding pH near 3 after 10 min, whereas high-ANC rocks yield paste pH of 7-8. In our coal mine example, the field tests were most effective when used in conjunction with stratigraphy. However, the same field tests have potential for routine use in any mine in which distinction of acid-generating rocks from acid-neutralising rocks is required. Calibration of field-based acid-base accounting characteristics of the rocks with laboratory-based static and/or kinetic tests is still necessary.

Critical loads of acidity for 90,000 lakes in northern Saskatchewan: A novel approach for mapping regional sensitivity to acidic deposition

NASA Astrophysics Data System (ADS)

Cathcart, H.; Aherne, J.; Jeffries, D. S.; Scott, K. A.

2016-12-01

Atmospheric emissions of sulphur dioxide (SO2) from large point sources are the primary concern for acidic deposition in western Canada, particularly in the Athabasca Oil Sands Region (AOSR) where prevailing winds may potentially carry SO2 over acid-sensitive lakes in northern Saskatchewan. A novel catchment-scale regression kriging approach was used to assess regional sensitivity and critical loads of acidity for the total lake population of northern Saskatchewan (89,947 lakes). Lake catchments were delineated using Thiessen polygons, and surface water chemistry was predicted for sensitivity indicators (calcium, pH, alkalinity, and acid neutralizing capacity). Critical loads were calculated with the steady state water chemistry model using regression-kriged base cations, sulphate, and dissolved organic carbon concentrations modelled from surface water observations (n > 800) and digital landscape-scale characteristics, e.g., climate, soil, vegetation, landcover, and geology maps. A large region (>13,726 km2) of two or more indicators of acid sensitivity (pH < 6 and acid neutralizing capacity, alkalinity, calcium < 50 μeq L-1) and low critical loads < 5 meq m-2 yr-1 were predicted on the Athabasca Basin. Exceedance of critical loads under 2006 modelled total sulphate deposition was predicted for 12% of the lakes (covering an area of 3742 km2), primarily located on the Athabasca Basin, within 100 km of the AOSR. There have been conflicting scientific reports of impacts from atmospheric emissions from the AOSR; the results of this study suggest that catchments in the Athabasca Basin within 100 km of the AOSR have received acidic deposition in excess of their critical loads and many of them may be at risk of ecosystem damage owing to their sensitivity.

Predicting nitrogen and acidity effects on long-term dynamics of dissolved organic matter.

PubMed

Rowe, E C; Tipping, E; Posch, M; Oulehle, F; Cooper, D M; Jones, T G; Burden, A; Hall, J; Evans, C D

2014-01-01

Increases in dissolved organic carbon (DOC) fluxes may relate to changes in sulphur and nitrogen pollution. We integrated existing models of vegetation growth and soil organic matter turnover, acid-base dynamics, and organic matter mobility, to form the 'MADOC' model. After calibrating parameters governing interactions between pH and DOC dissolution using control treatments on two field experiments, MADOC reproduced responses of pH and DOC to additions of acidifying and alkalising solutions. Long-term trends in a range of acid waters were also reproduced. The model suggests that the sustained nature of observed DOC increases can best be explained by a continuously replenishing potentially-dissolved carbon pool, rather than dissolution of a large accumulated store. The simulations informed the development of hypotheses that: DOC increase is related to plant productivity increase as well as to pH change; DOC increases due to nitrogen pollution will become evident, and be sustained, after soil pH has stabilised. Copyright © 2013 Elsevier Ltd. All rights reserved.

Synthesis carbon foams prepared from gelatin (CFG) for cadmium ion adsorption

NASA Astrophysics Data System (ADS)

Ulfa, M.; Ulfa, D. K.

2018-01-01

In this paper, carbon foam from gelatin (CFG) was synthesized by acid-catalyzed carbonization of gelatin solution on mild condition by the simple method. Gelatin (Ge) were used as sacrificial template and source of carbon. Sulphuric acid was used as acid catalyst. Carbon foam CFG sample were characterized by scanning electron microscope (SEM), nitrogen adsorption desorption and FTIR for knowing textural and structural properties of the sample. Carbon foam CFG sample demonstrated macro pipes-channel like with pore size that varies between 30-40 μ and surface area m 60-100 m2g-1. The carbon foams CFG sample were tested by using adsorption process for obtained their performance for decreasing Cd(II) ions from aqueous solutions. The adsorption capacities for cadmium was 46.7 mg/g obtained by using adsorbent dose 50 mg, initial concentration 50 ppm, contact time, 3 h; room temperature, stirring rate 150 rpm) which reached equilibrium at 55 min. Adsorption process fits using using Lagergren and Ho and McKay equation and measuring data

Tobacco LSU-like protein couples sulphur-deficiency response with ethylene signalling pathway.

PubMed

Moniuszko, Grzegorz; Skoneczny, Marek; Zientara-Rytter, Katarzyna; Wawrzyńska, Anna; Głów, Dawid; Cristescu, Simona M; Harren, Frans J M; Sirko, Agnieszka

2013-11-01

Most genes from the plant-specific family encoding Response to Low Sulphur (LSU)-like proteins are strongly induced in sulphur (S)-deficient conditions. The exact role of these proteins remains unclear; however, some data suggest their importance for plants' adjustment to nutrient deficiency and other environmental stresses. This work established that the regulation of ethylene signalling is a part of plants' response to S deficiency and showed the interaction between UP9C, a tobacco LSU family member, and one of the tobacco isoforms of 1-aminocyclopropane-1-carboxylic acid oxidase (ACO2A). Increase in ethylene level induced by S deficiency does not take place in tobacco plants with UP9C expressed in an antisense orientation. Based on transcriptomics data, this work also demonstrated that the majority of tobacco's response to S deficiency is misregulated in plants expressing UP9C-antisense. A link between response to S deficiency, ethylene sensing, and LSU-like proteins was emphasized by changes in expression of the genes encoding ethylene receptors and F-box proteins specific for the ethylene pathway.

Spectroscopic and computational study of a new isomer of salinomycin

NASA Astrophysics Data System (ADS)

Pankiewicz, Radosław

2013-09-01

A new derivative of polyether ionophore salinomycin was obtained as a result of a rearrangement catalysed by sulphuric acid in two-phase medium of water/methylene chloride solution. The new isomer was fully characterized by multinuclear 2D NMR, NOESY and MALDI-TOF. The properties of the new compound were additionally study by semiempirical (PM5) and DFT (B3LYP) methods. A potential mechanism of the rearrangement was also proposed.

Real-Time Prediction of Tropical Cyclone Intensity Using COAMPS-TC

DTIC Science & Technology

2012-01-01

tropospheric (UT) cloud fields (i.e., cirrus clouds) long after the initial eruption cycle from gradual particle settling and re-entrainment back into the... troposphere . Volcanic sul- fur dioxide and hydrogen sulfide vapor molecules are photo-oxidized in the LS, forming gaseous sulphuric acid, which in...concentration over the eastern United States at 1815 UTC on the 17th shown in Fig. 5(a), derived from NASA Ozone Monitoring Instrument (OMI) measurements

Studies on the effect of acid treated TiO{sub 2} on the electrical and tensile properties of hexanoyl chitosan-polystyrene-LiCF{sub 3}SO{sub 3} composite polymer electrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanif, Nur Shazlinda Muhammad; Shahril, Nur Syuhada Mohd; Azmar, Amisha

2015-08-28

Composite polymer electrolytes (CPEs) comprised of hexanoyl chitosan:polystyrene (90:10) blend, lithium triflouromethanesulfonate (LiCF{sub 3}SO{sub 3}) salt and titanium oxide (TiO{sub 2}) filler were prepared by solution casting technique. The TiO{sub 2} fillers were treated with 2% sulphuric acid (H{sub 2}SO{sub 4}) aqueous solution. The effect of acid treated TiO{sub 2} on the electrical and tensile properties of the electrolytes were investigated. Acid treated TiO{sub 2} decreased the electrolyte conductivity. Both the dielectric constant and dielectric loss decrease with increasing frequency and increases with increasing temperature. Relaxation times for ionic carriers were extracted from the loss tangent maximum peak at variousmore » temperatures. A distribution of relaxation time implied the non-Debye response. At all frequencies, ac conductivity increases with increasing temperature. An enhancement in the Young’s modulus was observed with the addition of TiO{sub 2}. The Young’s modulus increases with increasing TiO{sub 2} content. This is discussed using the percolation concept.« less

Biodiesel Derive Bio-oil of Hermetia illucens Pre-pupae Catalysed by Sulphonated Biochar

NASA Astrophysics Data System (ADS)

Yoong Leong, Siew; Chong, Soo Shin; Chin, Kah Seng

2018-03-01

This study investigates the development of biochar catalyst from bamboo applied for biodiesel synthesis. A non-conventional biodiesel feedstock was used in the in-situ transesterification reaction. This non-conventional feedstock is obtained from an insect's fly, the Hermetia illucens fly. Biochar derived from bamboo has been investigated as a promising catalyst for biodiesel synthesis. The biochar acid catalysts were prepared by sulphonation via impregnation with concentrated sulphuric acid. The prepared catalysts were investigated for their performance to catalyse in-situ transesterification via ultra-sonication of Hermetia illucens bio-oil. The effects of carbonisation time (1 hour and 2 hour) and temperature (400°C, 500°C and 600°C) as well as catalyst loading (5-20 wt% on oil basis) on the transesterification yield were studied. Result showed that the highest yield of FAME obtained was 95.6% with catalyst loading of 15 wt% carbonized at 500°C for 2 hours. Sharp band of methyl ester functional groups were observed in the FTIR spectra at 1735-1750cm-1. The composition of this methyl ester was further deduced using gas chromatography and the fatty acid was predominantly lauric acid.

Morphological changes of porphine films on graphite by perchloric and phosphoric electrolytes. An electrochemical-AFM study

NASA Astrophysics Data System (ADS)

Yivlialin, Rossella; Penconi, Marta; Bussetti, Gianlorenzo; Biroli, Alessio Orbelli; Finazzi, Marco; Duò, Lamberto; Bossi, Alberto

2018-06-01

Organic molecules have been proposed as promising candidates for electrode protection in acidic electrolytes. The use of tetraphenyl-porphines (H2TPP) as graphite surface-protecting agents in sulphuric acid (H2SO4) is one of the newest. With the aim of unveiling the mechanism of such a protective effect, in this paper we test the stability of a H2TPP thin film immersed in perchloric and phosphoric acid solutions that differently interact with porphyrins. The protective role of H2TPP is tested in the electrochemical potential range where the pristine graphite undergoes an oxidation process that erodes the surface and eventually exfoliate the stratified crystal. The electrochemical analysis is performed in a three-electrode cell, while the surface morphology is monitored ex-situ and in-situ by atomic force microscopy. Electrospray mass analysis is also employed to investigate the presence of H2TPP fragments in the solution. We find that the organic film is not stable in perchloric solution, while it is stable and avoids graphite surface corrosion in phosphoric acid solution. These results provide a rationale for the role played by free-base porphines in graphite protection.

The Fate of Lipid Biosignatures in a Mars-Analogue Sulfur Stream.

PubMed

Tan, Jonathan; Lewis, James M T; Sephton, Mark A

2018-05-15

Past life on Mars will have generated organic remains that may be preserved in present day Mars rocks. The most recent period in the history of Mars that retained widespread surface waters was the late Noachian and early Hesperian and thus possessed the potential to sustain the most evolved and widely distributed martian life. Guidance for investigating late Noachian and early Hesperian rocks is provided by studies of analogous acidic and sulfur-rich environments on Earth. Here we report organic responses for an acid stream containing acidophilic organisms whose post-mortem remains are entombed in iron sulphates and iron oxides. We find that, if life was present in the Hesperian, martian organic records will comprise microbial lipids. Lipids are a potential sizeable reservoir of fossil carbon on Mars, and can be used to distinguish between different domains of life. Concentrations of lipids, and particularly alkanoic or "fatty" acids, are highest in goethite layers that reflect high water-to-rock ratios and thus a greater potential for habitability. Goethite can dehydrate to hematite, which is widespread on Mars. Mars missions should seek to detect fatty acids or their diagenetic products in the oxides and hydroxides of iron associated with sulphur-rich environments.

Active-passive corrosion of iron-chromium-nickel alloys in hot concentrated sulphuric acid solutions

NASA Astrophysics Data System (ADS)

Kish, Joseph R.

1999-11-01

In the manufacture of sulphuric acid more stringent environmental standards and operation economics have forced the industry to improve product utilization, energy efficiency and reliability. A key to improving both the thermal efficiency and reliability is the use and/or development of more corrosion resistance materials including stainless steels, especially in the parts of the plant that handle the condensed acid. Application of more corrosion resistant material requires a better understanding of the corrosion mechanism involved in concentrated H2SO4-H2O (>90 wt.%) solutions. While corrosion kinetics of carbon steel, the traditional material of construction, are relatively well understood, this is much less true in the case of the cyclic active-passive corrosion of stainless steels. Models proposed to explain the cyclic active-passive corrosion involve a periodic formation of either a protective metal sulphate film or an insoluble sulphur layer. To better understand the reactivity and/or passivity of stainless steel in concentrated H2SO4-H2O solutions a study employing immersion and electrochemical techniques, including rotating electrodes, was conducted in order to clarify the following: (1) The state of stainless steel passivity. (2) The conditions in which passivity is stable. (3) The role played by the major alloying elements in establishing and maintaining the passive state. The study involved evaluating the corrosion behaviour of stainless steels S30403 and S43000 along with iron, chromium and nickel in 93.5 wt.% H2SO4 at temperatures between 25--80°C. Major discoveries of the study include: (1) A content of 17--18 wt.% chromium is sufficient to anodically passivate S43000 as the potential is made more noble. Passivity is not stable and requires anodic polarization. (2) Alloyed nickel plays an active role in improving the corrosion resistance of stainless steel. A content of 8 wt.% nickel is sufficient promote a periodic passivation of the base Fe-(17--18)wt.% Cr stainless steel under open-circuit conditions which reduces the corrosion rate by at least an order of magnitude. (3) The electrolysis of concentrated H2SO4-H 2O solutions involves a potential-dependent reduction of H2SO 4 molecules to sulphur-containing species with an oxidation state lower than six (6). The various reduction products have a significant effect on the stainless steel corrosion resistance. (4) Successful modelling of the corrosion of nickel has been accomplished by using a galvanic interaction between a noncontinuous nickel sulphide (NiS) deposit, formed in situ, and the uncovered nickel metal. (5) Successful modelling of the active-passive corrosion of S30403 has been accomplished using a galvanic interaction between NiS(Ni) and S43000.

Over production of fermentable sugar for bioethanol production from carbohydrate-rich Malaysian food waste via sequential acid-enzymatic hydrolysis pretreatment.

PubMed

Hafid, Halimatun Saadiah; Nor 'Aini, Abdul Rahman; Mokhtar, Mohd Noriznan; Talib, Ahmad Tarmezee; Baharuddin, Azhari Samsu; Umi Kalsom, Md Shah

2017-09-01

In Malaysia, the amount of food waste produced is estimated at approximately 70% of total municipal solid waste generated and characterised by high amount of carbohydrate polymers such as starch, cellulose, and sugars. Considering the beneficial organic fraction contained, its utilization as an alternative substrate specifically for bioethanol production has receiving more attention. However, the sustainable production of bioethanol from food waste is linked to the efficient pretreatment needed for higher production of fermentable sugar prior to fermentation. In this work, a modified sequential acid-enzymatic hydrolysis process has been developed to produce high concentration of fermentable sugars; glucose, sucrose, fructose and maltose. The process started with hydrothermal and dilute acid pretreatment by hydrochloric acid (HCl) and sulphuric acid (H 2 SO 4 ) which aim to degrade larger molecules of polysaccharide before accessible for further steps of enzymatic hydrolysis by glucoamylase. A kinetic model is proposed to perform an optimal hydrolysis for obtaining high fermentable sugars. The results suggested that a significant increase in fermentable sugar production (2.04-folds) with conversion efficiency of 86.8% was observed via sequential acid-enzymatic pretreatment as compared to dilute acid pretreatment (∼42.4% conversion efficiency). The bioethanol production by Saccharomyces cerevisiae utilizing fermentable sugar obtained shows ethanol yield of 0.42g/g with conversion efficiency of 85.38% based on the theoretical yield was achieved. The finding indicates that food waste can be considered as a promising substrate for bioethanol production. Copyright © 2017. Published by Elsevier Ltd.

Identification of Organic Sulfate Esters in d-Limonene Ozonolysis SOA Under Acidic Condition

NASA Astrophysics Data System (ADS)

Iinuma, Y.; Mueller, C.; Boege, O.; Herrmann, H.

2006-12-01

Secondary organic aerosol (SOA) components from gas phase ozonolysis of d-limonene were investigated in a series of indoor chamber experiments. The compounds smaller than 300 Da were quantified using capillary electrophoresis coupled to electrospray ionisation ion trap mass spectrometry (CE/ESI-ITMS). HPLC coupled to an ESI-TOFMS and an ESI-ITMS was used for structural study of dimmers and oligomers. Only 10% of the produced SOA could be attributed to low molecular weight carboxylic acids (Mw<300). The oxidation products which have molecular weights over 300 were detected regardless of the seed particle acidity but the concentrations of these compounds were much higher for acidic seed particle experiments. Strong signals of the compounds with mass to charge ratios (m/z) 281, 465 and 481 were detected when sulphuric acid was used in the seed particles. These compounds showed a strong fragment of m/z 97 in MS2 or MS3 spectra indicating the presence of sulfate in the structures. HPLC/ESI-TOFMS analysis suggests the elemental compositions of C10H17O7S-, C20H33O10S- and C20H33O11S- for m/z 281, 465 and 481, respectively. Based on MS^{n} and TOFMS results, they are most likely organic sulfate esters, possibly formed by a heterogeneous acid catalyzed reaction of a limonene oxidation product and sulfuric acid in the particle phase. The concentrations of the organic sulfate ester were as high as 3.7 μgm-3 for m/z 281.

Thermal degradation kinetics of polylactic acid/acid fabricated cellulose nanocrystal based bionanocomposites.

PubMed

Monika; Dhar, Prodyut; Katiyar, Vimal

2017-11-01

Cellulose nanocrystals (CNC) are fabricated from filter paper (as cellulosic source) by acid hydrolysis using different acids such as sulphuric (H 2 SO 4 ), phosphoric (H 3 PO 4 ), hydrochloric (HCl) and nitric (HNO 3 ) acid. The resulting acid derived CNC are melt mixed with Polylactic acid (PLA) using extruder at 180°C. Thermogravimetric (TGA) result shows that increase in 10% and 50% weight loss (T 10 , T 50 ) temperature for PLA-CNC film fabricated with HNO 3 , H 3 PO 4 and HCl derived CNC have improved thermal stability in comparison to H 2 SO 4 -CNC. Nonisothermal kinetic studies are carried out with modified-Coats-Redfern (C-R), Ozawa-Flynn-Wall (OFW) and Kissinger method to predict the kinetic and thermodynamic parameters. Subsequently prediction of these parameter leads to the proposal of thermal induced degradation mechanism of nanocomposites using Criado method. The distribution of E a calculated from OFW model are (PLA-H 3 PO 4 -CNC: 125-139 kJmol -1 ), (PLA-HNO 3 -CNC: 126-145 kJmol -1 ), (PLA-H 2 SO 4 -CNC: 102-123 kJmol -1 ) and (PLA-HCl-CNC: 140-182 kJmol -1 ). This difference among E a for the decomposition of PLA-CNC bionanocomposite is probably due to various acids used in this study. The E a calculated by these two methods are found in consonance with that observed from Kissinger method. Further, hyphenated TG-Fourier transform infrared spectroscopy (FTIR) result shows that gaseous products such as CO 2 , CO, lactide, aldehydes and other compounds are given off during the thermal degradation of PLA-CNC nanocomposite. Copyright © 2017 Elsevier B.V. All rights reserved.

Process design of SSCF for ethanol production from steam-pretreated, acetic-acid-impregnated wheat straw.

PubMed

Bondesson, Pia-Maria; Galbe, Mats

2016-01-01

Pretreatment is an important step in the production of ethanol from lignocellulosic material. Using acetic acid together with steam pretreatment allows the positive effects of an acid catalyst to be retained, while avoiding the negative environmental effects associated with sulphuric acid. Acetic acid is also formed during the pretreatment and hydrolysis of hemicellulose, and is a known inhibitor that may impair fermentation at high concentrations. The purpose of this study was to improve ethanol production from glucose and xylose in steam-pretreated, acetic-acid-impregnated wheat straw by process design of simultaneous saccharification and co-fermentation (SSCF), using a genetically modified pentose fermenting yeast strain Saccharomyces cerevisiae . Ethanol was produced from glucose and xylose using both the liquid fraction and the whole slurry from pretreated materials. The highest ethanol concentration achieved was 37.5 g/L, corresponding to an overall ethanol yield of 0.32 g/g based on the glucose and xylose available in the pretreated material. To obtain this concentration, a slurry with a water-insoluble solids (WIS) content of 11.7 % was used, using a fed-batch SSCF strategy. A higher overall ethanol yield (0.36 g/g) was obtained at 10 % WIS. Ethanol production from steam-pretreated, acetic-acid-impregnated wheat straw through SSCF with a pentose fermenting S. cerevisiae strain was successfully demonstrated. However, the ethanol concentration was too low and the residence time too long to be suitable for large-scale applications. It is hoped that further process design focusing on the enzymatic conversion of cellulose to glucose will allow the combination of acetic acid pretreatment and co-fermentation of glucose and xylose.

[Enzymatic methods in the analysis of musts and wines].

PubMed

Lafon-Lafourcade, S

1978-01-01

The enzymatic methods are based on the property of the enzymes to catalyse specifically and reversibly the conversion of certain metabolites. These methods, developed thanks to the industrial preparation of enzymes, can be applied with no major modification to the analysis of drinks. About 15 constituants of musts and wines can now be determined by these methods. If their cost price was not relatively high, their specificity, sensitivity and rapidity would enable them to compete with the most precise of chemical methods. This is why they are only used in analytic oenology when chemical analysis is most specific enough or too laborious. Enzymatic measurement allows one by its specificity to determine the amount of residual sugar that is fermentable in a dry wine and by its sensitivity to verifie the total disappearance of the malic acid of the wine. Its rapidity must make it preferable to the long and not very specific chemical measurement, especially concerning the determination of citric acid. But glycerol, ethanol and acetic acid can be measured by chemical or chromatographical means with sufficient precision and for a more modest price. In oenology the methods are essentially used for research. They have permitted the study of the combinations of sulphur anhydride in wines (measurement of cetonic acids). The determination of the isomeric nature of the lactic acid produced from sugars by lactic bacteria is based on their application; this determination is a criterium for the identification and classification of these microorganisms. The measurement of the lactic acid during vinification allows the early disclosure of the first effects of a bacterial development; inversely it permits the invalidation of the existence of a lactic sourness, which a high volatile acidity might point to. Lastly, the enzymatic measurement of gluconic acid allows the health of the crop to be controlled.

A modified approach for estimating the aquatic critical load of acid deposition in northern Saskatchewan, Canada

NASA Astrophysics Data System (ADS)

Whitfield, Colin J.; Mowat, Aidan C.; Scott, Kenneth A.; Watmough, Shaun A.

2016-12-01

Acid-sensitive ecosystems are found in northern Saskatchewan, which lies downwind of major sulphur (S) and nitrogen (N) emissions sources associated with the oil sands extraction industry. In order to protect these ecosystems against acidification, tolerance to acid deposition must be quantified. The suitability of the central empirical relationship used in the Steady-State Water Chemistry (SSWC) model to predict historical sulphate (SO4) concentrations was investigated, and an alternate approach for determining aquatic critical loads of acidity (CL(A)) was employed for the study lakes (n = 260). Critical loads of acidity were often low, with median values of 12-16 mmolc m-2 yr-1, with the lower value reflecting a region-specific limit for acid-neutralizing capacity identified in this study. Uncertain levels of atmospheric deposition in the region, however, are problematic for characterizing acidification risk. Accurate S and chloride (Cl) deposition are needed to identify catchment sources (and sinks) of these elements in the new approach for CL(A) calculation. Likewise, accurate depiction of atmospheric deposition levels can prove useful for evaluation of lake runoff estimates on which estimates of CL(A) are contingent. While CL(A) are low and exceedance may occur according to projected increases in S deposition in the near-term, S retention appears to be an important feature in many catchments and risk of acidification may be overstated should long-term S retention be occurring in peatlands.

Synthesis of sulfonated porous carbon nanospheres solid acid by a facile chemical activation route

NASA Astrophysics Data System (ADS)

Chang, Binbin; Guo, Yanzhen; Yin, Hang; Zhang, Shouren; Yang, Baocheng

2015-01-01

Generally, porous carbon nanospheres materials are usually prepared via a template method, which is a multi-steps and high-cost strategy. Here, we reported a porous carbon nanosphere solid acid with high surface area and superior porosity, as well as uniform nanospheical morphology, which prepared by a facile chemical activation with ZnCl2 using resorcinol-formaldehyde (RF) resins spheres as precursor. The activation of RF resins spheres by ZnCl2 at 400 °C brought high surface area and large volume, and simultaneously retained numerous oxygen-containing and hydrogen-containing groups due to the relatively low processing temperature. The presence of these functional groups is favorable for the modification of -SO3H groups by a followed sulfonation treating with sulphuric acid and organic sulfonic acid. The results of N2 adsorption-desorption and electron microscopy clearly showed the preservation of porous structure and nanospherical morphology. Infrared spectra certified the variation of surface functional groups after activation and the successful modification of -SO3H groups after sulfonation. The acidities of catalysts were estimated by an indirect titration method and the modified amount of -SO3H groups were examined by energy dispersive spectra. The results suggested sulfonated porous carbon nanospheres catalysts possessed high acidities and -SO3H densities, which endowed their significantly catalytic activities for biodiesel production. Furthermore, their excellent stability and recycling property were also demonstrated by five consecutive cycles.

Characterization of Streptomyces isolates causing colour changes of mural paintings in ancient Egyptian tombs.

PubMed

Abdel-Haliem, M E F; Sakr, A A; Ali, M F; Ghaly, M F; Sohlenkamp, C

2013-08-25

Paintings in ancient Egyptian tombs often suffer colour changes due to microbial growth and colonization. Streptomyces strains were isolated from mural paintings of Tell Basta and Tanis tombs (East of Nile Delta, Egypt) and were identified using biochemical and molecular methods. The16S rDNA sequences data indicated that isolated strains were closely related to S. coelicolor, S. albidofuscus, S. ambofaciens, S. canarius, S. parvullus, S. corchorusii, S. albidofuscus and S. nigrifaciens. It could be shown that Streptomyces strains are involved on a large scale in the colour changes of paintings and stone support by producing a wide range of metabolites such as acids (oxalic, citric and sulphuric acids), biopigments of melanin, carotenoids, and hydrogen sulphide. Copyright © 2013 Elsevier GmbH. All rights reserved.

[Comparative study of different extraction methods and assays of tannins in some pteridophytes].

PubMed

Laurent, S

1975-10-01

Various processes of extraction and quantitative analysis of a condensed tannin in a plant extract, which also includes some chlorogenic acids, have been examined. 60% methanol, at 50 degrees C, proved the most efficient extraction solvent. Several methods of analysis have been tried. The measure of the colour intensity obtained by the action of sulphuric vanilline on flavanols cannot be used because it depends on the tannin condensation stage. It is impossible to separate tannin from chlorogenic acids using the methods of adsorption by skin or nylon powders, or precipitation by polyvinylpyrrolidone. Only paper chromatography, followed by the distinct elution of the various phenolic compounds, allows the tannin evaluation by subtraction; but owing to the variability of the results, many more experiments are necessary. Some other processes are being studied.

Regional and global impacts of Criegee intermediates on atmospheric sulphuric acid concentrations and first steps of aerosol formation.

PubMed

Percival, Carl J; Welz, Oliver; Eskola, Arkke J; Savee, John D; Osborn, David L; Topping, David O; Lowe, Douglas; Utembe, Steven R; Bacak, Asan; McFiggans, Gordon; Cooke, Michael C; Xiao, Ping; Archibald, Alexander T; Jenkin, Michael E; Derwent, Richard G; Riipinen, Ilona; Mok, Daniel W K; Lee, Edmond P F; Dyke, John M; Taatjes, Craig A; Shallcross, Dudley E

2013-01-01

Carbonyl oxides ("Criegee intermediates"), formed in the ozonolysis of alkenes, are key species in tropospheric oxidation of organic molecules and their decomposition provides a non-photolytic source of OH in the atmosphere (Johnson and Marston, Chem. Soc. Rev., 2008, 37, 699, Harrison et al, Sci, Total Environ., 2006, 360, 5, Gäb et al., Nature, 1985, 316, 535, ref. 1-3). Recently it was shown that small Criegee intermediates, C.I.'s, react far more rapidly with SO2 than typically represented in tropospheric models, (Welz, Science, 2012, 335, 204, ref. 4) which suggested that carbonyl oxides could have a substantial influence on the atmospheric oxidation of SO2. Oxidation of 502 is the main atmospheric source of sulphuric acid (H2SO4), which is a critical contributor to aerosol formation, although questions remain about the fundamental nucleation mechanism (Sipilä et al., Science, 2010, 327, 1243, Metzger et al., Proc. Natl. Acad. Sci. U. S. A., 2010 107, 6646, Kirkby et al., Nature, 2011, 476, 429, ref. 5-7). Non-absorbing atmospheric aerosols, by scattering incoming solar radiation and acting as cloud condensation nuclei, have a cooling effect on climate (Intergovernmental Panel on Climate Change (IPCC), Climate Change 2007: The Physical Science Basis, Cambridge University Press, 2007, ref. 8). Here we explore the effect of the Criegees on atmospheric chemistry, and demonstrate that ozonolysis of alkenes via the reaction of Criegee intermediates potentially has a large impact on atmospheric sulphuric acid concentrations and consequently the first steps in aerosol production. Reactions of Criegee intermediates with SO2 will compete with and in places dominate over the reaction of OH with SO2 (the only other known gas-phase source of H2SO4) in many areas of the Earth's surface. In the case that the products of Criegee intermediate reactions predominantly result in H2SO4 formation, modelled particle nucleation rates can be substantially increased by the improved experimentally obtained estimates of the rate coefficients of Criegee intermediate reactions. Using both regional and global scale modelling, we show that this enhancement is likely to be highly variable spatially with local hot-spots in e.g. urban outflows. This conclusion is however contingent on a number of remaining uncertainties in Criegee intermediate chemistry.

Speciation and distribution characteristics of heavy metals and pollution assessments in the sediments of Nashina Lake, Heilongjiang, China.

PubMed

Li, Miao; Zang, Shuying; Xiao, Haifeng; Wu, Changshan

2014-05-01

Sediment core samples from Nashina Lake, Heilongjiang, China were collected using a gravity sampler. The cores were sliced horizontally at 1 cm each to determine the particle size, total concentrations and speciation of Cd, Cr, Cu, Mn, Ni, Pb, and Zn. Total concentrations of heavy metals were extracted using an acid mixture (containing hydro fluoric acid, nitric acid, and sulphuric acid) and analyzed using an inductively coupled plasma spectrometry. A sequential extraction procedure was employed to separate chemical species. Analysis of results indicate that the concentrations of heavy metals in the sediments of Nashina Lake in descending order are Mn, Cr, Zn, Pb, Ni, Cu, and Cd. The ratios of the average concentrations of four heavy metals (e.g.Cr, Cu, Ni, Zn) to their background values were >1; and those of Mn, Cd, and Pb were >1. Moreover, some toxic metals were mainly distributed in bioavailable fractions. For instance, both Cd and Mn were typically found in Acid-extractable species or Fe-Mn oxide species, and thus can be easily remobilized and enter the food chain. Finally, the analysis of geo-accumulation index showed that anthropogenic pollution levels of Cr, Cu, Mn, Ni, Zn were low, but those of Pb and Cd were at the moderate level. As both Pb and Cd are toxic metals, it is highly necessary to prohibit their transformation and accumulation in the sediments.

A wet chemical method for the estimation of carbon in uranium carbides.

PubMed

Chandramouli, V; Yadav, R B; Rao, P R

1987-09-01

A wet chemical method for the estimation of carbon in uranium carbides has been developed, based on oxidation with a saturated solution of sodium dichromate in 9M sulphuric acid, absorption of the evolved carbon dioxide in a known excess of barium hydroxide solution, and titration of the excess of barium hydroxide with standard potassium hydrogen phthalate solution. The carbon content obtained is in good agreement with that obtained by combustion and titration.

Optimizing the electrochemical performance of aqueous symmetric supercapacitors based on an activated carbon xerogel

NASA Astrophysics Data System (ADS)

Calvo, E. G.; Lufrano, F.; Staiti, P.; Brigandì, A.; Arenillas, A.; Menéndez, J. A.

2013-11-01

A highly porous carbon xerogel was synthesized by means of physical activation. The activated carbon xerogel, which displayed a well-developed porous texture (micro- and meso-porosity), was employed as electrode material in different supercapacitors. In assessing the performance of the supercapacitors, special attention was paid to their dimensions and the type of electrolyte used. Both the method of electrode manufacture (rolling and punching of 1 cm2 pellets vs. casting by means of a film applicator to produce 4 cm2 electrodes) and the type of supercapacitor (Swagelok (R) system vs. cell with graphite plate current collectors) were evaluated. The results reveal that the cells with larger electrodes were able to store higher amounts of energy. In addition to the cells, the electrochemical characteristics in aqueous electrolytes with a different pH were studied (H2SO4, Na2SO4 and KOH, 1 M). The highest capacitance values were achieved with sulphuric acid (196 F g-1 as opposed to 140 and 106 F g-1 for Na2SO4 and KOH, respectively), probably due to its higher ionic conductivity and the basic nature of the oxygen functionalities found on the surface of the carbon xerogel. Nevertheless, because of the corrosive character of sulphuric acid, Na2SO4 would be a more suitable electrolyte.

Bilberry and bilberry press cake as sources of dietary fibre

PubMed Central

Aura, Anna-Marja; Holopainen-Mantila, Ulla; Sibakov, Juhani; Kössö, Tuija; Mokkila, Mirja; Kaisa, Poutanen

2015-01-01

Background Dietary recommendations for Nordic countries urge the use of plant foods as a basis for healthy nutrition. Currently, the level of dietary fibre (DF) intake is not adequate. Berries are an elementary part of the recommended Nordic healthy diet and could be consumed in higher amounts. Materials and methods Finnish bilberries and a bilberry press cake from juice processing were studied for DF content, carbohydrate composition, and non-carbohydrate fibre content, which was analysed as sulphuric acid insoluble and soluble material. The microstructure of all samples was also studied using light microscopy and toluidine blue O, calcofluor, and acid fuchsin staining. Results The total DF contents of fresh and freeze-dried bilberries and the press cake were 3.0, 24.1, and 58.9%, respectively. Most of the DF was insoluble. Only about half of it was carbohydrate, the rest being mostly sulphuric acid–insoluble material, waxy cutin from skins, and resilient seeds. Bilberry seeds represented over half of the press cake fraction, and in addition to skin, they were the major DF sources. Microscopy revealed that skins in the press cake were intact and the surface of the seeds had thick-walled cells. Conclusions Bilberry press cake is thus a good source of insoluble non-carbohydrate DF, and could be used to provide DF-rich foods to contribute to versatile intake of DF. PMID:26652738

Continuous-flow leaching in a rotating coiled column for studies on the mobility of toxic elements in dust samples collected near a metallurgic plant.

PubMed

Fedotov, Petr S; Ermolin, Mikhail S; Ivaneev, Alexandr I; Fedyunina, Natalia N; Karandashev, Vasily K; Tatsy, Yury G

2016-03-01

Continuous-flow (dynamic) leaching in a rotating coiled column has been applied to studies on the mobility of Zn, Cd, Cu, Pb, Ni, Sb, As, S, and other potentially toxic elements in atmospherically deposited dust samples collected near a large copper smelter (Chelyabinsk region, Russia). Water and simulated "acid rain" (pH 4) were used as eluents. The technique enables not only the fast and efficient leaching of elements but as well time-resolved studies on the mobilization of heavy metals, sulphur, and arsenic in environmentally relevant forms to be made. It is shown that up to 1.5, 4.1, 1.9, 11.1, and 46.1% of Pb, As, Cu, Zn, and S, correspondingly, can be easily mobilized by water. Taking into consideration that the total concentrations of these elements in the samples under investigation are surprisingly high and vary in the range from 2.7 g/kg (for arsenic) to 15.5 g/kg (for sulphur), the environmental impact of the dust may be dramatic. The simulated acid rain results in somewhat higher recoveries of elements, except Cu and Pb. The proposed approach and the data obtained can very useful for the risk assessment related to the mobility of potentially toxic elements and their inclusion in the biogeochemical cycle. Copyright © 2015 Elsevier Ltd. All rights reserved.

Development of tuberous roots and sugar accumulation as related to invertase activity and mineral nutrition.

PubMed

Ricardo, C P; Sovia, D

1974-03-01

Sucrose storage in tuberous roots was not observed when the tissues had very high activities of acid invertase. High activities of the enzyme were always present in the roots at early stages of their development. In species where the activity of the enzyme decreased during root development, sucrose was stored. Thus, acid invertase was undetectable in mature roots of carrots (Daucus carota L.) where sucrose formed almost 80% of the dry matter. Conversely, radish (Raphanus sativus L.) and turnip (Brassica rapa L.) roots, in which the activity of the enzyme remained high until maturity, did not store appreciable amounts of sucrose (2% and 9%, respectively, of the dry matter in the mature roots), reducing sugars being the main reserve (more than 80% of the dry matter in mature turnips). The correlation between sucrose content and acid invertase activity was furthermore evident in both sucrose- and hexose-storing roots when the activity of this enzyme was affected by changes in the mineral nutrition. Deficiencies of nitrogen and sulphur reduced the activity of acid and alkaline invertases and led to increase in sucrose content and decrease in reducing sugars. However, the decline of alkaline invertase activity in tissues low in acid invertase had no clear effect on sugar content. Sodium chloride (10(-1)M) affected acid invertase and sugars in a manner similar to that of the two deficiencies, but had practically no effect on alkaline invertase. The changes in sugar content produced by the variations in mineral nutrition were small in hexose-storing roots in relation to those of sucrose-storing roots. It is possible that this result is related to the different levels of acid invertase in the two types of roots.

Evaluation of corrosion products formed by sulfidation as inhibitors of the naphthenic corrosion of AISI-316 steel

NASA Astrophysics Data System (ADS)

Sanabria-Cala, J. A.; Montañez, N. D.; Laverde Cataño, D.; Y Peña Ballesteros, D.; Mejía, C. A.

2017-12-01

Naphthenic acids present in oil from most regions worldwide currently stand as the main responsible for the naphthenic corrosion problems, affecting the oil-refining industry. The phenomenon of sulfidation, accompanying corrosion processes brought about by naphthenic acids in high-temperature refining plant applications, takes place when the combination of sulfidic acid (H2S) with Fe forms layers of iron sulphide (FeS) on the material surface, layers with the potential to protect the material from attack by other corrosive species like naphthenic acids. This work assessed corrosion products formed by sulfidation as inhibitors of naphthenic corrosion rate in AISI-316 steel exposed to processing conditions of simulated crude oil in a dynamic autoclave. Calculation of the sulfidation and naphthenic corrosion rates were determined by gravimetry. The surfaces of the AISI-316 gravimetric coupons exposed to acid systems; were characterized morphologically by X-Ray Diffraction (XRD) and X-ray Fluorescence by Energy Dispersive Spectroscopy (EDS) combined with Scanning Electron Microscopy (SEM). One of the results obtained was the determination of an inhibiting effect of corrosion products at 250 and 300°C, where lower corrosion rate levels were detected. For the temperature of 350°C, naphthenic corrosion rates increased due to deposition of naphthenic acids on the areas where corrosion products formed by sulfidation have lower homogeneity and stability on the surface, thus accelerating the destruction of AISI-316 steel. The above provides an initial contribution to oil industry in search of new alternatives to corrosion control by the attack of naphthenic acids, from the formation of FeS layers on exposed materials in the processing of heavy crude oils with high sulphur content.

Electrochemical process for electrode material of spent lithium ion batteries.

PubMed

Prabaharan, G; Barik, S P; Kumar, N; Kumar, L

2017-10-01

Electrochemical method for recovering cobalt and manganese from electrode materials of spent lithium ion batteries was studied. Electrochemical leaching of cobalt and manganese from electrode material was optimized by varying different process parameters such as time, acid concentration and current density. Both cobalt and manganese could effectively be leached out at a current density of 400A/m 2 in 3h using 2M sulphuric acid. In the subsequent study, the metallic cobalt and electrolytic manganese dioxides was recovered from the leach liquor at 200A/m 2 , pH 2-2.5 and 90°C after removing aluminum. The commercial feasibility of the study was tested in pilot scale. Overall recovery of Co, Cu and Mn was above 96%, 97% and 99%, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Extractive photometric determination of gold(III) with 1-(2',4',6'-trichlorophenyl)-4,4,6-trimethyl-(1H,4H)-2-pyrimidinethiol in presence of tri-iso-octylamine.

PubMed

Amuse, M A; Kuchekar, S R; Mote, N A; Chavan, M B

1985-10-01

Tervalent gold was determined spectrophotometrically as its anionic 1:4 gold-thiol complex extracted into chloroform from aqueous acidic medium (1.5M sulphuric acid) in the presence of tri-iso-octylamine. The complex exhibits maximum absorption at 480 nm (molar absorptivity 4.60 x 10(3) l.mole(-1).cm(-1)) and Beer's law is obeyed in the concentration range 5-50 microg of gold(III) per ml. The relative standard deviation and relative error, calculated from ten determinations of solutions containing 15 microg of gold(III) per ml were 1.0% and 0.8%. The method is simple, selective and reproducible. It permits separation of gold(III) from associated elements and its determination in synthetic mixtures.

Determination of arsenic in geological materials by x-ray fluorescence spectrometry after solvent extraction and deposition on a filter

USGS Publications Warehouse

Hubert, A.E.

1983-01-01

Rock, soil, or sediment samples are decomposed with a mixture of nitric and sulphuric adds. After reduction from arsenic(V) with ammonium thiosulphate, arsenic(III) is extracted as the chlorocomplex into benzene from a sulphuric-hydrochloric acid medium. The benzene solution is transferred onto a filter-paper disc impregnated with a solution of sodium bicarbonate and potassium sodium tartrate, and the benzene allowed to evaporate. The arsenic present is determined by X-ray fluorescence. In a 0.5-g sample, 1-1000 ppm of arsenic can be determined. The close proximity of the lead L?? peak (2?? 48.73??), to the arsenic K?? peak (2?? 48.83??) does not cause any interference, because lead is not extracted under the experimental conditions. Arsenic values obtained are in agreement with those reported for various reference samples. ?? 1983.

Prediction of intramuscular fat content and major fatty acid groups of lamb M. longissimus lumborum using Raman spectroscopy.

PubMed

Fowler, Stephanie M; Ponnampalam, Eric N; Schmidt, Heinar; Wynn, Peter; Hopkins, David L

2015-12-01

A hand held Raman spectroscopic device was used to predict intramuscular fat (IMF) levels and the major fatty acid (FA) groups of fresh intact ovine M. longissimus lumborum (LL). IMF levels were determined using the Soxhlet method, while FA analysis was conducted using a rapid (KOH in water, methanol and sulphuric acid in water) extraction procedure. IMF levels and FA values were regressed against Raman spectra using partial least squares regression and against each other using linear regression. The results indicate that there is potential to predict PUFA (R(2)=0.93) and MUFA (R(2)=0.54) as well as SFA values that had been adjusted for IMF content (R(2)=0.54). However, this potential was significantly reduced when correlations between predicted and observed values were determined by cross validation (R(2)cv=0.21-0.00). Overall, the prediction of major FA groups using Raman spectra was more precise (relative reductions in error of 0.3-40.8%) compared to the null models. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biodiesel from dewatered wastewater sludge: a two-step process for a more advantageous production.

PubMed

Pastore, Carlo; Lopez, Antonio; Lotito, Vincenzo; Mascolo, Giuseppe

2013-07-01

Alternative approaches for obtaining biodiesel from municipal sludge have been successfully investigated. In order to avoid the expensive conventional preliminary step of sludge drying, dewatered sludge (TSS: 15wt%) was used as starting material. The best performance in terms of yield of fatty acid methyl esters (18wt%) with the lowest energy demand (17MJkgFAME(-1)) was obtained by a new two-step approach based on hexane extraction carried out directly on dewatered acidified (H2SO4) sludge followed by methanolysis of extracted lipids. It was found that sulphuric acid plays a key role in the whole process not only for the transesterification of glycerides but also for the production of new free fatty acids from soaps and their esterification with methanol. In addition to biodiesel production, the investigated process allows valorization of primary sludge as it turns it into a valuable source of chemicals, namely sterols (2.5wt%), aliphatic alcohols (0.8wt%) and waxes (2.3wt%). Copyright © 2013 Elsevier Ltd. All rights reserved.

Lactobacillus and Leuconostoc volatilomes in cheese conditions.

PubMed

Pogačić, Tomislav; Maillard, Marie-Bernadette; Leclerc, Aurélie; Hervé, Christophe; Chuat, Victoria; Valence, Florence; Thierry, Anne

2016-03-01

New strains are desirable to diversify flavour of fermented dairy products. The objective of this study was to evaluate the potential of Leuconostoc spp. and Lactobacillus spp. in the production of aroma compounds by metabolic fingerprints of volatiles. Eighteen strains, including five Lactobacillus species (Lactobacillus fermentum, Lactobacillus helveticus, Lactobacillus paracasei, Lactobacillus rhamnosus, Lactobacillus sakei) and three Leuconostoc species (Leuconostoc citreum, Leuconostoc lactis, and Leuconostoc mesenteroides) were incubated for 5 weeks in a curd-based slurry medium under conditions mimicking cheese ripening. Populations were enumerated and volatile compounds were analysed by headspace trap gas chromatography-mass spectrometry (GC-MS). A metabolomics approach followed by multivariate statistical analysis was applied for data processing and analysis. In total, 12 alcohols, 10 aldehydes, 7 esters, 11 ketones, 5 acids and 2 sulphur compounds were identified. Very large differences in concentration of volatile compounds between the highest producing strains and the control medium were observed in particular for diacetyl, 2-butanol, ethyl acetate, 3-methylbutanol, 3-methylbutanoic acid and 2-methylbutanoic acid. Some of the characterized strains demonstrated an interesting aromatizing potential to be used as adjunct culture.

The effect of thermal and ultrasonic treatment on amino acid composition, radical scavenging and reducing potential of hydrolysates obtained from simulated gastrointestinal digestion of cowpea proteins.

PubMed

Quansah, Joycelyn K; Udenigwe, Chibuike C; Saalia, Firibu K; Yada, Rickey Y

2013-03-01

The effect of thermal and ultrasonic treatment of cowpea proteins (CP) on amino acid composition, radical scavenging and reducing potential of hydrolysates (CPH) obtained from in vitro simulated gastrointestinal digestion of CP was evaluated. Hydrolysis of native and treated CP with gastrointestinal pepsin and pancreatin yielded CPH that displayed antioxidant activities based on oxygen radical scavenging capacity (ORAC), ferric reducing antioxidant power (FRAP) and superoxide radical scavenging activity (SRSA). CPH derived from the treated CP yielded higher ORAC values than CPH from untreated proteins. However, lower significant FRAP and SRSA values were observed for these samples compared to untreated CPH (p < 0.05). Amino acid analysis indicated that CP processing decreased total sulphur-containing amino acids in the hydrolysates, particularly cysteine. The amount of cysteine appeared to be positively related to FRAP and SRSA values of CPH samples, but not ORAC. The results indicated that thermal and ultrasonic processing of CP can reduce the radical scavenging and reducing potential of the enzymatic hydrolysates possibly due to the decreased amounts of cysteine. Since the hydrolysates were generated with gastrointestinal enzymes, it is possible that the resulting compounds are produced to exert some health functions during normal consumption of cowpea.

Scales of Hydrogen-Bonding Workshop Held in London, England on 1-3 July 1987

DTIC Science & Technology

1987-07-03

medium (a perfluorinated compound , FC-75), hoping to attain the basicity of CF3 CH2OH and (CF 3.2CHOH. The frequency shifts of the 3818 cm v(OH) band of...bond basicity for nonassoclated compounds , pro.ided that the reference acids in each case led toi*values that were almost the same - around 65". ’ 1...experimental measurements JOSE-LOUIS M. ABBOUD * The hydrogen-bonding basicity of oxygen and sulphur compounds MICHAEL H. ABRAHAM, PRISCILLA L

Electrochemical Studies on Minoxidil and Its Determination in Tablets by Differential-Pulse Polarography.

DTIC Science & Technology

1984-01-16

AD-R76 981 ELECTROCHEMICAL STUDIES ON MINOXIDIL AND ITS j/j IDETERMINATION IN TABLETS BY..(U) UTAH UNIV SALT LAKE AS CITY DEPT OF CHEMISTRY L...INSTRUCTIONES 2. QVT CCESSIN ". 3 krCIPII-.,n I CATALOG Numtnk 22 ’TTE(d.t8v . TYPE OF R4EPORT a PERIOD COEd Electrochemical Studies on Minoxidil and... minoxidil in pharmaceutical dosage forms. The extracting . solvent was methani and the supporting electrolyte was 1.0 N sulphuric acid. L. An excellent

Processing of copper converter slag for metals reclamation: Part II: mineralogical study.

PubMed

Deng, Tong; Ling, Yunhan

2004-10-01

Chemical and mineralogical characterizations of a copper converter slag, and its products obtained by curing with strong sulphuric acid and leaching with hot water, were carried out using ore microscopy, scanning electronic microscopy with energy dispersive spectrometry, wave-length dispersive X-ray fluorescence spectrometry, X-ray diffractometry and chemical phase analysis, which provided necessary information to develop a new process for treating such slag and further understanding of the chemical and mineralogical changes in the process.

Joint analysis of deposition fluxes and atmospheric concentrations of inorganic nitrogen and sulphur compounds predicted by six chemistry transport models in the frame of the EURODELTAIII project

NASA Astrophysics Data System (ADS)

Vivanco, M. G.; Bessagnet, B.; Cuvelier, C.; Theobald, M. R.; Tsyro, S.; Pirovano, G.; Aulinger, A.; Bieser, J.; Calori, G.; Ciarelli, G.; Manders, A.; Mircea, M.; Aksoyoglu, S.; Briganti, G.; Cappelletti, A.; Colette, A.; Couvidat, F.; D'Isidoro, M.; Kranenburg, R.; Meleux, F.; Menut, L.; Pay, M. T.; Rouïl, L.; Silibello, C.; Thunis, P.; Ung, A.

2017-02-01

In the framework of the UNECE Task Force on Measurement and Modelling (TFMM) under the Convention on Long-range Transboundary Air Pollution (LRTAP), the EURODELTAIII project is evaluating how well air quality models are able to reproduce observed pollutant air concentrations and deposition fluxes in Europe. In this paper the sulphur and nitrogen deposition estimates of six state-of-the-art regional models (CAMx, CHIMERE, EMEP MSC-W, LOTOS-EUROS, MINNI and CMAQ) are evaluated and compared for four intensive EMEP measurement periods (25 Feb-26 Mar 2009; 17 Sep-15 Oct 2008; 8 Jan-4 Feb 2007 and 1-30 Jun 2006). For sulphur, this study shows the importance of including sea salt sulphate emissions for obtaining better model results; CMAQ, the only model considering these emissions in its formulation, was the only model able to reproduce the high measured values of wet deposition of sulphur at coastal sites. MINNI and LOTOS-EUROS underestimate sulphate wet deposition for all periods and have low wet deposition efficiency for sulphur. For reduced nitrogen, all the models underestimate both wet deposition and total air concentrations (ammonia plus ammonium) in the summer campaign, highlighting a potential lack of emissions (or incoming fluxes) in this period. In the rest of campaigns there is a general underestimation of wet deposition by all models (MINNI and CMAQ with the highest negative bias), with the exception of EMEP, which underestimates the least and even overestimates deposition in two campaigns. This model has higher scavenging deposition efficiency for the aerosol component, which seems to partly explain the different behaviour of the models. For oxidized nitrogen, CMAQ, CAMx and MINNI predict the lowest wet deposition and the highest total air concentrations (nitric acid plus nitrates). Comparison with observations indicates a general underestimation of wet oxidized nitrogen deposition by these models, as well as an overestimation of total air concentration for all the campaigns, except for the 2006 campaign. This points to a low efficiency in the wet deposition of oxidized nitrogen for these models, especially with regards to the scavenging of nitric acid, which is the main driver of oxidized N deposition for all the models. CHIMERE, LOTOS-EUROS and EMEP agree better with the observations for both wet deposition and air concentration of oxidized nitrogen, although CHIMERE seems to overestimate wet deposition in the summer period. This requires further investigation, as the gas-particle equilibrium seems to be biased towards the gas phase (nitric acid) for this model. In the case of MINNI, the frequent underestimation of wet deposition combined with an overestimation of atmospheric concentrations for the three pollutants indicates a low efficiency of the wet deposition processes. This can be due to several reasons, such as an underestimation of scavenging ratios, large vertical concentration gradients (resulting in small concentrations at cloud height) or a poor parameterization of clouds. Large differences between models were also found for the estimates of dry deposition. However, the lack of suitable measurements makes it impossible to assess model performance for this process. These uncertainties should be addressed in future research, since dry deposition contributes significantly to the total deposition for the three deposited species, with values in the same range as wet deposition for most of the models, and with even higher values for some of them, especially for reduced nitrogen.

Identification of three new phase II metabolites of a designer drug methylone formed in rats by N-demethylation followed by conjugation with dicarboxylic acids.

PubMed

Židková, Monika; Linhart, Igor; Balíková, Marie; Himl, Michal; Dvořáčková, Veronika; Lhotková, Eva; Páleníček, Tomáš

2018-06-01

1. Methylone (3,4-methylenedioxy-N-methylcathinone, MDMC), which appeared on the illicit drug market in 2004, is a frequently abused synthetic cathinone derivative. Known metabolic pathways of MDMC include N-demethylation to normethylone (3,4-methylenedioxycathinone, MDC), aliphatic chain hydroxylation and oxidative demethylenation followed by monomethylation and conjugation with glucuronic acid and/or sulphate. 2. Three new phase II metabolites, amidic conjugates of MDC with succinic, glutaric and adipic acid, were identified in the urine of rats dosed subcutaneously with MDMC.HCl (20 mg/kg body weight) by LC-ESI-HRMS using synthetic reference standards to support identification. 3. The main portion of administered MDMC was excreted unchanged. Normethylone, was a major urinary metabolite, of which a minor part was conjugated with dicarboxylic acids. 4. Previously identified ring-opened metabolites 4-hydroxy-3-methoxymethcathinone (4-OH-3-MeO-MC), 3-hydroxy-4-methoxymeth-cathinone (3-OH-4-MeO-MC) and 3,4-dihydroxymethcathinone (3,4-di-OH-MC) mostly in conjugated form with glucuronic and/or sulphuric acids were also detected. 5. Also, ring-opened metabolites derived from MDC, namely, 4-hydroxy-3-methoxycathinone (4-OH-3-MeO-C), 3-hydroxy-4-methoxycathinone (3-OH-4-MeO-C) and 3,4-dihydroxycathinone (3,4-di-OH-C) were identified for the first time in vivo.

Chronic aspartame intake causes changes in the trans-sulphuration pathway, glutathione depletion and liver damage in mice.

PubMed

Finamor, Isabela; Pérez, Salvador; Bressan, Caroline A; Brenner, Carlos E; Rius-Pérez, Sergio; Brittes, Patricia C; Cheiran, Gabriele; Rocha, Maria I; da Veiga, Marcelo; Sastre, Juan; Pavanato, Maria A

2017-04-01

No-caloric sweeteners, such as aspartame, are widely used in various food and beverages to prevent the increasing rates of obesity and diabetes mellitus, acting as tools in helping control caloric intake. Aspartame is metabolized to phenylalanine, aspartic acid, and methanol. Our aim was to study the effect of chronic administration of aspartame on glutathione redox status and on the trans-sulphuration pathway in mouse liver. Mice were divided into three groups: control; treated daily with aspartame for 90 days; and treated with aspartame plus N-acetylcysteine (NAC). Chronic administration of aspartame increased plasma alanine aminotransferase (ALT) and aspartate aminotransferase activities and caused liver injury as well as marked decreased hepatic levels of reduced glutathione (GSH), oxidized glutathione (GSSG), γ-glutamylcysteine ​​(γ-GC), and most metabolites of the trans-sulphuration pathway, such as cysteine, S-adenosylmethionine (SAM), and S-adenosylhomocysteine ​​(SAH). Aspartame also triggered a decrease in mRNA and protein levels of the catalytic subunit of glutamate cysteine ligase (GCLc) and cystathionine γ-lyase, and in protein levels of methionine adenosyltransferase 1A and 2A. N-acetylcysteine prevented the aspartame-induced liver injury and the increase in plasma ALT activity as well as the decrease in GSH, γ-GC, cysteine, SAM and SAH levels and GCLc protein levels. In conclusion, chronic administration of aspartame caused marked hepatic GSH depletion, which should be ascribed to GCLc down-regulation and decreased cysteine levels. Aspartame triggered blockade of the trans-sulphuration pathway at two steps, cystathionine γ-lyase and methionine adenosyltransferases. NAC restored glutathione levels as well as the impairment of the trans-sulphuration pathway. Copyright © 2017. Published by Elsevier B.V.

Study on corrosion resistance of high - entropy alloy in medium acid liquid and chemical properties

NASA Astrophysics Data System (ADS)

Florea, I.; Buluc, G.; Florea, R. M.; Soare, V.; Carcea, I.

2015-11-01

High-entropy alloy is a new alloy which is different from traditional alloys. The high entropy alloys were started in Tsing Hua University of Taiwan since 1995 by Yeh et al. Consisting of a variety of elements, each element occupying a similar compared with other alloy elements to form a high entropy. We could define high entropy alloys as having approximately equal concentrations, made up of a group of 5 to 11 major elements. In general, the content of each element is not more than 35% by weight of the alloy. During the investigation it turned out that this alloy has a high hardness and is also corrosion proof and also strength and good thermal stability. In the experimental area, scientists used different tools, including traditional casting, mechanical alloying, sputtering, splat-quenching to obtain the high entropy alloys with different alloying elements and then to investigate the corresponding microstructures and mechanical, chemical, thermal, and electronic performances. The present study is aimed to investigate the corrosion resistance in a different medium acid and try to put in evidence the mechanical properties. Forasmuch of the wide composition range and the enormous number of alloy systems in high entropy alloys, the mechanical properties of high entropy alloys can vary significantly. In terms of hardness, the most critical factors are: hardness/strength of each composing phase in the alloy, distribution of the composing phases. The corrosion resistance of an high entropy alloy was made in acid liquid such as 10%HNO3-3%HF, 10%H2SO4, 5%HCl and then was investigated, respectively with weight loss experiment. Weight loss test was carried out by put the samples into the acid solution for corrosion. The solution was maintained at a constant room temperature. The liquid formulations used for tests were 3% hydrofluoric acid with 10% nitric acid, 10% sulphuric acid, 5% hydrochloric acid. Weight loss of the samples was measured by electronic scale.

Insulin at pH 2: structural analysis of the conditions promoting insulin fibre formation.

PubMed

Whittingham, Jean L; Scott, David J; Chance, Karen; Wilson, Ashley; Finch, John; Brange, Jens; Guy Dodson, G

2002-04-26

When insulin solutions are subjected to acid, heat and agitation, the normal pattern of insulin assembly (dimers-->tetramers-->hexamers) is disrupted; the molecule undergoes conformational changes allowing it to follow an alternative aggregation pathway (via a monomeric species) leading to the formation of insoluble amyloid fibres. To investigate the effect of acid pH on the conformation and aggregation state of the protein, the crystal structure of human insulin at pH 2.1 has been determined to 1.6 A resolution. The structure reveals that the native fold is maintained at low pH, and that the molecule is still capable of forming dimers similar to those found in hexameric insulin structures at higher pH. Sulphate ions are incorporated into the molecule and the crystal lattice where they neutralise positive charges on the protein, stabilising its structure and facilitating crystallisation. The sulphate interactions are associated with local deformations in the protein, which may indicate that the structure is more plastic at low pH. Transmission electron microscopy analysis of insulin fibres reveals that the appearance of the fibres is greatly influenced by the type of acid employed. Sulphuric acid produces distinctive highly bunched, truncated fibres, suggesting that the sulphate ions have a sophisticated role to play in fibre formation, rather as they do in the crystal structure. Analytical ultracentrifugation studies show that in the absence of heating, insulin is predominantly dimeric in mineral acids, whereas in acetic acid the equilibrium is shifted towards the monomer. Hence, the effect of acid on the aggregation state of insulin is also complex. These results suggest that acid conditions increase the susceptibility of the molecule to conformational change and dissociation, and enhance the rate of fibrillation by providing a charged environment in which the attractive forces between the protein molecules is increased. (c) 2002 Elsevier Science Ltd.

Characterization of water treatment sludge and its reuse as coagulant.

PubMed

Ahmad, Tarique; Ahmad, Kafeel; Ahad, Abdul; Alam, Mehtab

2016-11-01

Coagulation-flocculation process results in the generation of large volume of waste or residue, known as water treatment sludge (WTS), in the purification of surface water for potable supplies. Sustainable management of the inevitable waste requires careful attention from the plant operators and sludge managers. In this study, WTS produced with the optimum alum dose of 30 ml/L at the laboratory scale has been treated with sulphuric acid to bring forth a product known as sludge reagent product (SRP). The performance of SRP is evaluated for its efficiency in removing the colloidal suspensions from the Yamuna river water over wide pH range of 2-13. 1% sludge acidified with sulphuric acid of normality 2.5 at the rate of 0.05 ml/ml sludge has been observed as the optimum condition for preparing SRP from WTS. The percentage turbidity removal is greater at higher pH value and increases with increasing the dosage of SRP. The optimum SRP dosage of 8 ml/L in the pH range of 6-8 performed well in removing the colloidal suspension and other impurities from the Yamuna water. The quality of treated water met the prescribed standards for most of the quality parameters. Thus, SRP has the potential to substitute the conventional coagulants partially or completely in the water treatment process, depending on the quality needed at the users end. Copyright © 2016 Elsevier Ltd. All rights reserved.

Distribution of sulphuric acid aerosols in the clouds and upper haze of Venus using Venus Express VAST and VeRa temperature profiles

NASA Astrophysics Data System (ADS)

Parkinson, Christopher D.; Gao, Peter; Schulte, Rick; Bougher, Stephen W.; Yung, Yuk L.; Bardeen, Charles G.; Wilquet, Valérie; Vandaele, Ann Carine; Mahieux, Arnaud; Tellmann, Silvia; Pätzold, Martin

2015-08-01

Observations from Pioneer Venus and from SPICAV/SOIR aboard Venus Express (VEx) have shown the upper haze (UH) of Venus to be highly spatially and temporally variable, and populated by multiple particle size modes. Previous models of this system (e.g., Gao et al., 2014. Icarus 231, 83-98), using a typical temperature profile representative of the atmosphere (viz., equatorial VIRA profile), did not investigate the effect of temperature on the UH particle distributions. We show that the inclusion of latitude-dependent temperature profiles for both the morning and evening terminators of Venus helps to explain how the atmospheric aerosol distributions vary spatially. In this work we use temperature profiles obtained by two instruments onboard VEx, VeRa and SPICAV/SOIR, to represent the latitudinal temperature dependence. We find that there are no significant differences between results for the morning and evening terminators at any latitude and that the cloud base moves downwards as the latitude increases due to decreasing temperatures. The UH is not affected much by varying the temperature profiles; however, the haze does show some periodic differences, and is slightly thicker at the poles than at the equator. We also find that the sulphuric acid "rain" seen in previous models may be restricted to the equatorial regions of Venus, such that the particle size distribution is relatively stable at higher latitudes and at the poles.

Oxidative desulfurization of dibenzothiophene from model oil using ionic liquids as extracting agent

NASA Astrophysics Data System (ADS)

Taha, Mohd F.; Atikah, N.; Chong, F. K.; Shaharun, Maizatul S.

2012-09-01

The oxidative desulfurization of dibenzothiophene (DBT) from model oil (in n-dodecane) was carried out using ionic liquid as the extractant and catalyst, and hydrogen peroxide (H2O2) in combination with acetic acid (CH3COOH) and sulphuric acid (H2SO4) as the oxidant. The ionic liquids used were 1-butyl-3-methylimidazolium octyl sulphate ([Bmim][OcSO4]) and 1-butyl-3-methylimidazolium acetate ([Bmim][Ac]). The effect of the amounts of H2O2 on oxidative desulphurization of model oil was first investigated without the usage of ionic liquids at room temperature. The results indicate that greater amount of H2O2 give higher desulfurization and the maximum desulfurization in this study, i.e. 34 %, was occurred when the molar ratio of H2O2 to sulfur was 5:1. With the usage of ionic liquid and the molar ratio of 5:1 (H2O2:sulfur), the efficiency of DBT removal from model oil was increased significantly in terms of percent removal and removal time. Ionic liquid of [Bmim][OcSO4] performed better than [Bmim][Ac] with 72 % DBT removal. When molar ratio of H2O2 to sulphur was 5:1, volume ratio of ionic liquid to model oil was 1:1 and mixing time was 60 min at room temperature. The results indicate the potential of ionic liquids as the extractant and catalyst for oxidative desulfurization of hydrocarbon fuels.

The effect of zinc (Zn) content to cell potential value and efficiency aluminium sacrificial anode in 0.2 M sulphuric acid environment

NASA Astrophysics Data System (ADS)

Akranata, Ahmad Ridho; Sulistijono, Awali, Jatmoko

2018-04-01

Sacrificial anode is sacirifial component that used to protect steel from corrosion. Generally, the component are made of aluminium and zinc in water environment. Sacrificial anode change the protected metal structure become cathodic with giving current. The advantages of aluminium is corrosion resistance, non toxicity and easy forming. Zinc generally used for coating in steel to prevent steel from corrosion. This research was conducted to analyze the effect of zinc content to the value of cell potential and efficiency aluminium sacrificial anode with sand casting method in 0.2 M sulphuric acid environment. The sacrificial anode fabrication made with alloying aluminium and zinc metals with variation composition of alloy with pure Al, Al-3Zn, Al-6Zn, and Al-9Zn with open die sand casting process. The component installed with ASTM A36 steel. After the research has been done the result showed that addition of zinc content increase the cell potential, protection efficiency, and anode efficiency from steel plate. Cell potential value measurement and weight loss measurement showed that addition of zinc content increase the cell potential value into more positive that can protected the ASTM A36 steel more efficiently that showed in weight loss measurement where the protection efficiency and anodic efficiency of Al-9Zn sacrificial anode is better than protection efficiency and anodic efficiency of pure Al. The highest protection efficiency gotten by Al-9Zn alloy

Staphylococcus aureus SufT: an essential iron-sulphur cluster assembly factor in cells experiencing a high-demand for lipoic acid.

PubMed

Mashruwala, Ameya A; Roberts, Christina A; Bhatt, Shiven; May, Kerrie L; Carroll, Ronan K; Shaw, Lindsey N; Boyd, Jeffrey M

2016-12-01

Staphylococcus aureus SufT is composed solely of the domain of unknown function 59 (DUF59) and has a role in the maturation of iron-sulphur (Fe-S) proteins. We report that SufT is essential for S. aureus when growth is heavily reliant upon lipoamide-utilizing enzymes, but dispensable when this reliance is decreased. LipA requires Fe-S clusters for lipoic acid (LA) synthesis and a ΔsufT strain had phenotypes suggestive of decreased LA production and decreased activities of lipoamide-requiring enzymes. Fermentative growth, a null clpC allele, or decreased flux through the TCA cycle diminished the demand for LA and rendered SufT non-essential. Abundance of the Fe-S cluster carrier Nfu was increased in a ΔclpC strain and a null clpC allele was unable to suppress the LA requirement of a ΔsufT Δnfu strain. Over-expression of nfu suppressed the LA requirement of the ΔsufT strain. We propose a model wherein SufT, and by extension the DUF59, is essential for the maturation of holo-LipA in S. aureus cells experiencing a high demand for lipoamide-dependent enzymes. The findings presented suggest that the demand for products of Fe-S enzymes is a factor governing the usage of one Fe-S cluster assembly factor over another in the maturation of apo-proteins. © 2016 John Wiley & Sons Ltd.

Optimised deconjugation of androgenic steroid conjugates in bovine urine.

PubMed

Pedersen, Mikael; Frandsen, Henrik L; Andersen, Jens H

2017-04-01

After administration of steroids to animals the steroids are partially metabolised in the liver and kidney to phase 2 metabolites, i.e., glucuronic acid or sulphate conjugates. During analysis these conjugated metabolites are normally deconjugated enzymatically with aryl sulphatase and glucuronidase resulting in free steroids in the extract. It is well known that some sulphates are not deconjugated using aryl sulphatase; instead, for example, solvolysis can be used for deconjugation of these aliphatic sulphates. The effectiveness of solvolysis on androgenic steroid sulphates was tested with selected aliphatic steroid sulphates (boldenone sulphate, nortestosteron sulphate and testosterone sulphate), and the method was validated for analysis of androgenic steroids in bovine urine using free steroids, steroid sulphates and steroid glucuronides as standards. Glucuronidase and sulphuric acid in ethyl acetate were used for deconjugation and the extract was purified by solid-phase extraction. The final extract was evaporated to dryness, re-dissolved and analysed by LC-MS/MS.

Thermometric titration of thorium with EDTA in the presence of large excess of neutral sodium salts.

PubMed

Doi, K

1980-11-01

The thermometric titration of Th(IV) in the presence of neutral sodium salts, sulphuric acid or acetic acid with EDTA has been studied. The effect of each on the observed heat values for the titration is discussed. For sodium perchlorate media, DeltaH values of -9 and -21 kJ/mole have been estimated for the formation of the Th(IV)-EDTA chelate at mu --> 0 and mu = 0.5 (NaClO(4)), respectively. The -DeltaH values increase steadily with increase in concentration of sodium perchlorate up to at least 3M. For the titration of Th(IV) in the presence of a large excess of sodium nitrate the use of sodium iodide as a masking reagent has been examined: large amounts of Bi and Cu(II) are masked and a masking effect is observed for small amounts of Ni.

Taurine-induced attenuation of MPP+ neurotoxicity in vitro: a possible role for the GABA(A) subclass of GABA receptors.

PubMed

O'Byrne, M B; Tipton, K F

2000-05-01

Taurine is a sulphur-containing beta-amino acid found in high (millimolar) concentrations in excitable tissues such as brain and heart. Its suggested roles include osmoregulator, thermoregulator, neuromodulator, and potential neurotransmitter. This amino acid has also been shown to be released in large concentrations during ischaemia and excitotoxin-induced neuronal damage. Here we report a protective effect of taurine against MPP(+)-induced neurotoxicity in coronal slices from rat brain. Significant protective effects were observed at taurine concentrations of 20 and 1 mM, suggesting a potential role for taurine in cases of neuronal insult. Studies with the synthetic taurine analogues taurine phosphonate, guanidinoethane sulphonate, and trimethyltaurine suggested the observed effect to be mediated via an extracellular mechanism. The use of GABA receptor ligands muscimol and bicuculline indicated the effect to be mediated through activation of GABA(A) receptors.

Detecting changes in the nutritional value and elemental composition of transgenic sorghum grain

NASA Astrophysics Data System (ADS)

Ndimba, R.; Grootboom, A. W.; Mehlo, L.; Mkhonza, N. L.; Kossmann, J.; Barnabas, A. D.; Mtshali, C.; Pineda-Vargas, C.

2015-11-01

We have previously demonstrated that poor digestibility in sorghum can be addressed by using RNA interference (RNAi) to suppress kafirin synthesis. The approach resulted in a twofold improvement in overall protein digestibility levels. In the present study, the effect of this targeted kafirin suppression on other grain quality parameters was investigated. Several significant changes in the proximate composition, amino acid profile and the bulk mineral content were detected. Importantly, the most limiting amino acid, lysine, was significantly increased in the transgenic grains by up to 39%; whilst mineral elements in the bulk, such as sulphur (S) and zinc (Zn) were reduced by up to 15.8% and 21% respectively. Elemental mapping of the grain tissue, using micro-PIXE, demonstrated a significant decrease in Zn (>75%), which was localised to the outer endosperm region, whilst TEM revealed important changes to the protein body morphology of the transgenic grains.

RADIATION DOSIMETER

DOEpatents

Balkwell, W.R. Jr.; Adams, G.D. Jr.

1960-05-10

An improvement was made in the determination of amounts of ionizing radiation, particularly low-energy beta particles of less than 1000 rad total dose by means of fluid-phase dosimeter employing a stabilized-- sensitized ferrous-ferric colorimetric system in a sulphuric acid medium. The improvement in the dosimeter consists of adding to the ferrous-ferric system in concentrations of 10/sub -2/ to 10/sup -4/M an organic compound having one or more carboxylic or equivalent groups, such compounds being capable of chelating or complexing the iron ions in the solution. Suitable sensitizing and stabilizing agents are benzoic, phthalic, salicylic, malonic, lactic, maleic, oxalic, citric, succinic, phenolic tartaric, acetic, and adipic acid, as well as other compounds which are added to the solution alone or in certain combinations. As in conventional fluid-phase dosimeters, the absorbed dosage is correlated with a corresponding change in optical density at particular wavelengths of the solution.

Surface characterisation of ethylene propylene diene rubber upon exposure to aqueous acidic solution

NASA Astrophysics Data System (ADS)

Mitra, Susanta; Ghanbari-Siahkali, Afshin; Kingshott, Peter; Hvilsted, Søren; Almdal, Kristoffer

2006-07-01

Two types of pure ethylene propylene diene rubbers were exposed to two different acids for varying period of time. Surface characterisation was carried out using X-ray photoelectron spectroscopy (XPS). Two EPDM rubbers selected for this study were comparable in co-monomer compositions but significantly different with respect to molar mass and the presence of long chain branching. Both rubbers contained 5-ethylidene-2-norbornene (ENB) as diene. Solution cast films of pure EPDM samples were exposed in two different acidic solutions, viz. chromosulphuric (Cr (VI)/H 2SO 4) and sulphuric acid (H 2SO 4) (20%, v/v) at ambient temperature from 1 to 12 weeks. XPS analysis indicated that several oxygenated species were formed on the surface of both rubbers after exposure. It was postulated from the XPS analyses that both aqueous acidic solutions attacked the olefinic double bonds (C dbnd C) of ENB. Furthermore, 20% Cr (VI)/H 2SO 4 also attacked the allylic carbon-hydrogen (C sbnd H) bonds of ENB resulting in more oxygenated species on the surface compared to 20% H 2SO 4 under identical conditions. Cr (VI) in the 20% Cr (VI)/H 2SO 4 was found to play an important role in alteration of surface chemistry. Studies using a model system consisting of EPDM mixed with Cr (VI) and Cr (III) salts revealed that the change of oxidation state from Cr (VI) to Cr (III) as a consequence of direct involvement of Cr (VI) in the chemical alteration of EPDM surfaces. Interestingly, the presence of long chain branching and molar mass did not significantly influence the chemical processes owing to the acid treatment.

Enhanced fermentable sugar production from kitchen waste using various pretreatments.

PubMed

Hafid, Halimatun Saadiah; Rahman, Nor'Aini Abdul; Md Shah, Umi Kalsom; Baharudin, Azhari Samsu

2015-06-01

The kitchen waste fraction in municipal solid waste contains high organic matter particularly carbohydrate that can contribute to fermentable sugar production for subsequent conversion to bioethanol. This study was carried out to evaluate the influence of single and combination pretreatments of kitchen waste by liquid hot water, mild acid pretreatment of hydrochloric acid (HCl) and sulphuric acid (H2SO4) and enzymatic hydrolysis (glucoamylase). The maximum total fermentable sugar produced after combination pretreatment by 1.5% HCl and glucoamylase consisted of 93.25 g/L glucose, 0.542 g/L sucrose, 0.348 g/L maltose, and 0.321 g/L fructose. The glucose released by the combination pretreatment method was 0.79 g glucose/g KW equivalent to 79% of glucose conversion. The effects of the pre-treatment on kitchen waste indicated that the highest solubilization was 40% by the combination method of 1.5% HCl and glucoamylase. The best combination pre-treatment gave concentrations of lactic acid, acetic acid, and propionic acid of 11.74 g/L, 6.77 g/L, and 1.02 g/L, respectively. The decrease of aliphatic absorbance bands of polysaccharides at 2851 and 2923 cm(-1) and the increase on structures of carbonyl absorbance bands at 1600 cm(-1) reflects the progress of the kitchen waste hydrolysis to fermentable sugars. Overall, 1.5% HCl and glucoamylase treatment was the most profitable process as the minimum selling price of glucose was USD 0.101/g kitchen waste. Therefore, the combination pretreatment method was proposed to enhance the production of fermentable sugar, particularly glucose from kitchen waste as the feedstock for bioethanol production. Copyright © 2015 Elsevier Ltd. All rights reserved.

The significant role of carboxylated carbonaceous fragments in the electrochemistry of carbon nanotubes.

PubMed

Ma, Xiao; Jia, Li; Zhang, Lu; Zhu, Liande

2014-04-01

Carbon nanotubes (CNTs) have been widely employed as electrode materials in diverse branches of electrochemistry, which are claimed to display dramatically improved electrochemical behaviour compared to the conventional carbon materials. But a series of recent publications have demonstrated that the electrocatalysis of CNTs might be due to the presence of some impurities, such as metallic catalysts, nanographitic particles and amorphous carbon. For this reason, CNTs are usually purified or treated with nitric acid or nitric and sulphuric acid prior to their versatile applications. However, the strong acidic and oxidative conditions are so aggressive that serious erosion of the tube structures has inevitably taken place, which creates defects on the sidewalls and gives rise to numerous molecular byproducts, commonly referred as carboxylated carbonaceous fragments (CCFs). The adsorption of CCFs on CNTs greatly alters the surface conditions of CNTs which may significantly impact on their electrochemical properties. To this end, we wish to disclose whether the electrocatalysis of the nitric acid purified CNTs is affected by the adsorption of the CCFs. Ascorbic acid (AA) and β-nicotinamide adenine dinucleotide (NADH) as selected as the targeting benchmarks that are known to be insensitive to the presence of metallic impurities, which may guarantee the preclusion of the promoting contributions from the metallic catalysts resident in CNTs. We have demonstrated that the electrocatalytic activities of the CNTs are actually dominated by the adsorbed CCFs generated during the acidic pre-treatment. After removal of the CCFs by base rinse, the electrocatalytic properties of CNTs are greatly deteriorated and degraded to the level similar to the conventional graphite powder. We believe this finding is particularly meaningful to uncover the mysterious electrocatalysis of CNTs. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nutritional quality and health benefits of chickpea (Cicer arietinum L.): a review.

PubMed

Jukanti, A K; Gaur, P M; Gowda, C L L; Chibbar, R N

2012-08-01

Chickpea (Cicer arietinum L.) is an important pulse crop grown and consumed all over the world, especially in the Afro-Asian countries. It is a good source of carbohydrates and protein, and protein quality is considered to be better than other pulses. Chickpea has significant amounts of all the essential amino acids except sulphur-containing amino acids, which can be complemented by adding cereals to the daily diet. Starch is the major storage carbohydrate followed by dietary fibre, oligosaccharides and simple sugars such as glucose and sucrose. Although lipids are present in low amounts, chickpea is rich in nutritionally important unsaturated fatty acids such as linoleic and oleic acids. β-Sitosterol, campesterol and stigmasterol are important sterols present in chickpea oil. Ca, Mg, P and, especially, K are also present in chickpea seeds. Chickpea is a good source of important vitamins such as riboflavin, niacin, thiamin, folate and the vitamin A precursor β-carotene. As with other pulses, chickpea seeds also contain anti-nutritional factors which can be reduced or eliminated by different cooking techniques. Chickpea has several potential health benefits, and, in combination with other pulses and cereals, it could have beneficial effects on some of the important human diseases such as CVD, type 2 diabetes, digestive diseases and some cancers. Overall, chickpea is an important pulse crop with a diverse array of potential nutritional and health benefits.

THE CHEMISTRY OF THE LIVER IN ACUTE YELLOW ATROPHY

PubMed Central

Wells, H. Gideon

1907-01-01

From the liver of a young man who died of typical, " idiopathic" acute yellow atrophy of the liver, after an illness of six weeks, there were isolated and identified the following amino acids: Histidin, lysin, tyrosin, leucin, glycocoll, alanin, prolin, glutaminic acid, aspartic acid. These were found free in extracts of the liver, and presumably represent products of the autolysis of liver cells, although the amount of soluble non-protein nitrogen present in the extracts was so large as to suggest that there must be some other source for these substances. Small quantities of free proteoses and peptones, and of xanthin and hypoxanthin, were also found in the extracts. In the insoluble proteins of the liver the proportion of diamino acids was decreased slightly as compared with normal livers. The proportion of protein phosphorus was increased, probably because of active regenerative proliferation, while the sulphur was normal in amount. Iron was increased because of the large quantity of blood in the liver and the hematogenous pigmentation of the liver cells. Gelatigenous material was increased both absolutely and relatively, because of the loss of parenchyma and the proliferation of the stroma. The proportion of water to solids was much increased, there having been a loss of over two-thirds of the entire parenchymatous elements of the liver. The amount of fat, lecithin and cholesterin was not far from that normal for the liver. PMID:19867115

Preparation of Biopolyol by Solvolysis Liquefaction of Oil Palm Mesocarp Fibre using Polyhydric Alchohol

NASA Astrophysics Data System (ADS)

Kormin, Shaharuddin; Rus, Anika Zafiah M.; Azahari, M. Shafiq M.

2017-08-01

Liquefied oil palm mesocarp fibre (LOPMF) is a promising natural material that can be used as biopolyol of polyurethane foam. The aim of this study was to utilizing solvolysis liquefaction conversion technology of oil palm mesocarp fibre (OPMF) for polyurethane (PU) foam. LOPMF was obtained with liquefaction of fibre in polyhydric alchohol (PA) such as ethylene glycol (EG), polyethylene glycol (PEG) and glycerol (GLY) as liquefaction solvent and sulphuric acid (H2SO4) in three different OPMF/PA ratio (1/2, 1/3 and 1/4) in conventional glass reactor. During the liquefaction, cellulose, semi-cellulose and lignin are decomposed, which results in changes of acid value and hydroxyl value. Liquefied OPMF and residues were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results revealed that almost 50% of the OPMF converted into biopolyol product within 2 hours with OPMF/PA ratio of 1/4. Biopolyol produced under different condition showed viscosities from 210 to 450 Pa.s. The hydroxyl and acid values of the liquefied OPMF varied with the liquefied conditions. It was observed that with an increase in the liquefaction solvent (PA) amount in the mixture resulted in a high acid value and hydroxyl value for the OPMF. High reaction temperature combining with low OPMF material to solvent ratio resulted low hydroxyl number of LOPMF. The result in this study showed that biopolyol was suitable monomer for polyurethane synthesis.

The Production of Printed Circuit Boards, Photo-Anodised and Screen Printed Instrument Panels.

DTIC Science & Technology

1981-01-01

Laboratories, Melbourne 12. RELEASE LIMITATIONS (of the document): Approved for Public Release. 12.0. OVERSEAS: N.0.1 I P.R. 1 A I I B I I C I D EI 13...solutions. 5.1 baths Required (N.B. Tanks shoula be of rigid P.V.C.) 1. Amonium persulphate solution 100 gm/L. 2. Sulphuric acid 10% (A.R. GRADE...120 degrees C for at least 10 mins. Etchant 1: 55% weight/volume solution of ferric nitrate used at 49 degrees C. This solution is made by adding

A structurally driven analysis of thiol reactivity in mammalian albumins.

PubMed

Spiga, Ottavia; Summa, Domenico; Cirri, Simone; Bernini, Andrea; Venditti, Vincenzo; De Chiara, Matteo; Priora, Raffaella; Frosali, Simona; Margaritis, Antonios; Di Giuseppe, Danila; Di Simplicio, Paolo; Niccolai, Neri

2011-04-01

Understanding the structural basis of protein redox activity is still an open question. Hence, by using a structural genomics approach, different albumins have been chosen to correlate protein structural features with the corresponding reaction rates of thiol exchange between albumin and disulfide DTNB. Predicted structures of rat, porcine, and bovine albumins have been compared with the experimentally derived human albumin. High structural similarity among these four albumins can be observed, in spite of their markedly different reactivity with DTNB. Sequence alignments offered preliminary hints on the contributions of sequence-specific local environments modulating albumin reactivity. Molecular dynamics simulations performed on experimental and predicted albumin structures reveal that thiolation rates are influenced by hydrogen bonding pattern and stability of the acceptor C34 sulphur atom with donor groups of nearby residues. Atom depth evolution of albumin C34 thiol groups has been monitored during Molecular Dynamic trajectories. The most reactive albumins appeared also the ones presenting the C34 sulphur atom on the protein surface with the highest accessibility. High C34 sulphur atom reactivity in rat and porcine albumins seems to be determined by the presence of additional positively charged amino acid residues favoring both the C34 S⁻ form and the approach of DTNB. Copyright © 2011 Wiley Periodicals, Inc.

[Quality assessment of sulfur-fumigated paeoniae alba radix].

PubMed

Wang, Zhao; Chen, Yu-Wu; Wang, Qiong; Sun, Lei; Xu, Wei-Yi; Jin, Hong-Yu; Ma, Shuang-Cheng

2014-08-01

The samples of sulfur-fumigated Paeoniae Alba Radix acquired both by random spot check from domestic market and self-production by the research group in the laboratory were used to evaluate the effects of sulphur fumigation on the quality of Paeoniae Alba Radix by comparing sulfur-fumigated degree and character, the content of paeoniflorin and paeoniflorin sulfurous acid ester, and changes of the fingerprint. We used methods in Chinese Pharmacopeia to evaluate the character of sulfur-fumigated Paeoniae Alba Radix and determinate the content of aulfur-fumigated paeoniflorin. LC-MS method was used to analyze paeoniflorin-converted products. HPLC fingerprint methods were established to evaluate the differences on quality by similarity. Results showed that fumigated Paeoniae Alba Radix became white and its unique fragrance disappeared, along with the production of pungent sour gas. It also had a significant effect on paeoniflorin content. As sulfur smoked degree aggravated, paeoniflorin content decreased subsequently, some of which turned into paeoniflorin sulfurous acid ester, and this change was not reversible. Fingerprint also showed obvious changes. Obviously, sulfur fumigation had severe influence on the quality of Paeoniae Alba Radix, but we can control the quality of the Paeoniae Alba Radix by testing the paeoniflorin sulfurous acid ester content.

Synthesis of palm oil fatty acid and trimethylolpropane based ester for biolubricant base stocks

NASA Astrophysics Data System (ADS)

Nor, Nurazira Mohd; Derawi, Darfizzi; Salimon, Jumat

2018-04-01

RBD palm oil become one of the interesting renewable resources in biolubricant application. However, palm oil cannot be used directly as lubricant due to some performance limitations such as thermal and oxidative stability. This drawback can be overcome by chemical modification through esterification with polyhydric alcohol such as trimethylolpropane (TMP). The synthesis of ester was carried out via esterification of palm oil fatty acid (POFA) with TMP in the presence of 2% sulphuric acid as catalyst at 150 °C for 5 hours. Gas Chromatography equipped with a Flame Ionization Detector (GC-FID) was used to determine the percentage composition of POTMP ester. The structure confirmation of POTMP ester was proven by Fourier Transformation Infra-Red (FTIR), proton and carbon Nuclear Magnetic Resonance (1H-NMR and 13C-NMR) spectroscopy analysis. The result showed that POTMP ester has successfully synthesized with 97.7% composition of triesters (TE), proved by GC chromatogram. Presence of ester group also evidenced by 1H NMR at 2.27-2.30 ppm and 13C NMR at 173.52-173.54 ppm. The percentage yield of POTMP ester produced was 82% and exist in liquid form at room temperature.

Kinetic Study on the Removal of Iron from Gold Mine Tailings by Citric Acid

NASA Astrophysics Data System (ADS)

Mashifana, T.; Mavimbela, N.; Sithole, N.

2018-03-01

The Gold mining generates large volumes of tailings, with consequent disposal and environmental problems. Iron tends to react with sulphur to form pyrite and pyrrhotite which then react with rain water forming acid rain. The study focuses on the removal of iron (Fe) from Gold Mine tailings; Fe was leached using citric acid as a leaching reagent. Three parameters which have an effect on the removal of Fe from the gold mine tailings, namely; temperature (25 °C and 50 °C), reagent concentration (0.25 M, 0.5 M, 0.75 M and 1 M) and solid loading ratio (20 %, 30 % and 40 %) were investigated. It was found that the recovery of Fe from gold mine tailings increased with increasing temperature and reagent concentration, but decreased with increasing solid loading ratio. The optimum conditions for the recovery of Fe from gold mine tailings was found to be at a temperature of 50 ºC, reagent concentration of 1 M and solid loading of 20 %. Three linear kinetic models were investigated and Prout-Tompkins kinetic model was the best fit yielding linear graphs with the highest R2 values.

Environmental radioactivity assessment around old uranium mining sites near Mangualde (Viseu), Portugal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carvalho, Fernando P.; Torres, Lubelia M.; Oliveira, Joao M.

2007-07-01

Uranium ore was extracted in the surroundings of Mangualde city, North of Portugal, in the mines of Cunha Baixa, Quinta do Bispo and Espinho until a few years ago. Mining waste, milling tailings and acid mine waters are the on site remains of this extractive activity. Environmental radioactivity measurements were performed in and around these sites in order to assess the dispersal of radionuclides from uranium mining waste and the spread of acidic waters resulting from the in situ uranium leaching with sulphuric acid. Results show migration of acid waters into groundwater around the Cunha Baixa mine. This groundwater ismore » tapped by irrigation wells in the agriculture area near the Cunha Baixa village. Water from wells displayed uranium ({sup 238}U) concentrations up to 19x10{sup 3} mBq L{sup -1} and sulphate ion concentrations up to 1070 mg L{sup -1}. These enhanced concentrations are positively correlated with low water pH, pointing to a common origin for radioactivity, dissolved sulphate, and acidity in underground mining works. Radionuclide concentrations were determined in horticulture and farm products from this area also and results suggest low soil to plant transfer of radionuclides and low food chain transfer of radionuclides to man. Analysis of aerosols in surface air showed re suspension of dust from mining and milling waste heaps. Therefore, it is recommended to maintain mine water treatment and to plan remediation of these mine sites in order to prevent waste dispersal in the environment. (authors)« less

Antitumoural Sulphur and Selenium Heteroaryl Compounds: Thermal Characterization and Stability Evaluation.

PubMed

Alcolea, Verónica; Garnica, Pablo; Palop, Juan A; Sanmartín, Carmen; González-Peñas, Elena; Durán, Adrián; Lizarraga, Elena

2017-08-08

The physicochemical properties of a compound play a crucial role in the cancer development process. In this context, polymorphism can become an important obstacle for the pharmaceutical industry because it frequently leads to the loss of therapeutic effectiveness of some drugs. Stability under manufacturing conditions is also critical to ensure no undesired degradations or transformations occur. In this study, the thermal behaviour of 40 derivatives of a series of sulphur and selenium heteroaryl compounds with potential antitumoural activity were studied. In addition, the most promising cytotoxic derivatives were analysed by a combination of differential scanning calorimetry, X-ray diffraction and thermogravimetric techniques in order to investigate their polymorphism and thermal stability. Moreover, stability under acid, alkaline and oxidative media was tested. Degradation under stress conditions as well as the presence of polymorphism was found for the compounds VA6E and VA7J, which might present a hurdle to carrying on with formulation. On the contrary, these obstacles were not found for derivative VA4J.

Sulphate absorption across biological membranes.

PubMed

Mitchell, Stephen C; Waring, Rosemary H

2016-01-01

1. Sulphonation is unusual amongst the common Phase II (condensation; synthetic) reactions experienced by xenobiotics, in that the availability of the conjugating agent, sulphate, may become a rate-limiting factor. This sulphate is derived within the body via the oxygenation of sulphur moieties liberated from numerous ingested compounds including the sulphur-containing amino acids. Preformed inorganic sulphate also makes a considerable contribution to this pool. 2. There has been a divergence of opinion as to whether or not inorganic sulphate may be readily absorbed from the gastrointestinal tract and this controversy still continues in some quarters. Even more so, is the vexing question of potential absorption of inorganic sulphate via the lungs and through the skin. 3. This review examines the relevant diverse literature and concludes that sulphate ions may move across biological membranes by means of specific transporters and, although the gastrointestinal tract is by far the major portal of entry, some absorption across the lungs and the skin may take place under appropriate circumstances.

The analysis of oral air using selected ion flow tube mass spectrometry in persons with and without a history of oral malodour.

PubMed

Ross, B M; Dadgostar, N; Bloom, M; McKeown, L

2009-05-01

Oral malodour is a common disorder predominantly caused by bacterial metabolism of food stuffs in the mouth. It is routinely diagnosed and monitored by either the subjective rating or the measurement of oral volatile sulphur compound (VSC) levels. Non-sulphur compounds are also believed to contribute significantly to the condition although there is currently no direct means to assess their levels. In this study, we utilized selective flow tube mass spectrometry (SIFT-MS) to measure, in real time, a range of sulphur and non-sulphur containing compounds in oral air to determine whether the technique can be used to objectively monitor oral malodour. Oral malodour was assessed using organoleptic scores in subjects with and without a history of oral malodour (n = 18) by a trained rater, while the chemical composition of oral air was analysed by both VSC sensor and SIFT-MS. Total VSC levels were significantly correlated with levels of hydrogen sulphide and methylmercaptan measured by SIFT-MS, but not with organoleptic scores. In subjects with elevated organoleptic score, only levels of methylmercaptan were significantly elevated. In three subjects with elevated tongue organoleptic scores but normal total VSC levels, SIFT-MS suggested that one subject possessed high levels of oral acetone while another had high oral levels of acetic acid. Our data suggest that SIFT-MS can be used to assess a wide range of compounds in oral air in addition to VSC to provide a clearer picture of the chemical nature of malodour. This may assist in the diagnosis and monitoring of the condition.

Investigation of corrosion of welded joints of austenitic and duplex stainless steels

NASA Astrophysics Data System (ADS)

Topolska, S.

2016-08-01

Investigation of corrosion resistance of materials is one of the most important tests that allow determining their functional properties. Among these tests the special group consist electrochemical investigations, which let to accelerate the course of the process. These investigations allow rapidly estimating corrosion processes occurring in metal elements under the influence of the analysed environment. In the paper are presented results of investigations of the resistance to pitting corrosion of the steel of next grades: austenitic 316L and duplex 2205. It was also analysed the corrosion resistance of welded joints of these grades of steel. The investigations were conducted in two different corrosion environments: in the neutral one (3.5 % sodium chloride) and in the aggressive one (0.1 M sulphuric acid VI). The obtained results indicate different resistance of analysed grades of steel and their welded joints in relation to the corrosion environment. The austenitic 316L steel characterizes by the higher resistance to the pitting corrosion in the aggressive environment then the duplex 2205 steel. In the paper are presented results of potentiodynamic tests. They showed that all the specimens are less resistant to pitting corrosion in the environment of sulphuric acid (VI) than in the sodium chloride one. The 2205 steel has higher corrosion resistance than the 316L stainless steel in 3.5% NaCl. On the other hand, in 0.1 M H2SO4, the 316L steel has a higher corrosion resistance than the 2205 one. The weld has a similar, very good resistance to pitting corrosion like both steels.

Volatile sulphur compounds and pathways of L-methionine catabolism in Williopsis yeasts.

PubMed

Tan, Amelia W J; Lee, Pin-Rou; Seow, Yi-Xin; Ong, Peter K C; Liu, Shao-Quan

2012-08-01

Volatile sulphur compounds (VSCs) are important to the food industry due to their high potency and presence in many foods. This study assessed for the first time VSC production and pathways of L: -methionine catabolism in yeasts from the genus Williopsis with a view to understanding VSC formation and their potential flavour impact. Five strains of Williopsis saturnus (var. saturnus, var. subsufficiens, var. suavolens, var. sargentensis and var. mrakii) were screened for VSC production in a synthetic medium supplemented with L: -methionine. A diverse range of VSCs were produced including dimethyl disulphide, dimethyl trisulphide, 3-(methylthio)-1-propanal (methional), 3-(methylthio)-1-propanol (methionol), 3-(methylthio)-1-propene, 3-(methylthio)-1-propyl acetate, 3-(methylthio)-1-propanoic acid (methionic acid) and ethyl 3-(methylthio)-1-propanoate, though the production of these VSCs varied between yeast strains. W. saturnus var. saturnus NCYC22 was selected for further studies due to its relatively high VSC production. VSC production was characterised step-wise with yeast strain NCYC22 in coconut cream at different L: -methionine concentrations (0.00-0.20%) and under various inorganic sulphate (0.00-0.20%) and nitrogen (ammonia) supplementation (0.00-0.20%), respectively. Optimal VSC production was obtained with 0.1% of L: -methionine, while supplementation of sulphate had no significant effect. Nitrogen supplementation showed a dramatic inhibitory effect on VSC production. Based on the production of VSCs, the study suggests that the Ehrlich pathway of L: -methionine catabolism is operative in W. saturnus yeasts and can be manipulated by adjusting certain nutrient parameters to control VSC production.

Potential of Sulphur-containing Amino Acids in the Prevention of Catecholamine-induced Arrhythmias.

PubMed

Adameova, Adriana; Tappia, Paramjit S; Hatala, Robert; Dhalla, Naranjan S

2018-01-30

Various physiological and pathological stimuli can hypersensitize the sympathetic nervous system resulting in a substantial release of catecholamines (CA) and consequent alterations in excitation-contraction coupling and excitation-transcription coupling. It has been shown that oxidation products of CA, rather than CA themselves, are responsible for such adaptation to a new equilibrium. While chronic, sustained accumulation of CA and their toxic products are associated with the depression in cardiac contractile force and remodeling, acute excessive release of CA can result in brief oxidative bursts and serious damage leading in lethal arrhythmias. In response to such oxidative stress, dysregulation of ion homeostasis, activation of neurohumoral system, immune and inflammatory responses, are augmented. These events are inter-related, and as a complex promote electrical instability. Likewise, remodeling occurring after the loss of cardiomyocytes, induces the development of a proarrhythmogenic environment. Thus, CA oxidation products may be involved in triggering arrhythmias as a result of both changes in cardiac cell automaticity and conduction velocity. In contrast, sulphur-containing amino acids (S-AA), in particular taurine and its precursor cysteine have been shown to modulate redox state of the heart. However, the multiple anti-oxidant properties of S-AA are unlikely to be exclusively responsible for their anti-arrhythmic action. They also possess additional cytoprotective effects which can stabilize electrical activity of the heart. It is concluded that specific S-AA may attenuate deleterious effects of supraphysiological levels of CA and this could serve as an important mechanism for the treatment and/or prevention of arrhythmogenesis. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Multiple applications of the U.S. EPA 1312 leach procedure to mine waste from the Animas watershed, SW Colorado

USGS Publications Warehouse

Fey, David L.; Church, Stan E.; Driscoll, Rhonda L.; Adams, Monique G.

2011-01-01

Eleven acid-sulphate and quartz-sericite-pyrite altered mine waste samples from the Animas River watershed in SW Colorado were subjected to a series of 5 to 6 successive leaches using the US EPA 1312 leach protocol to evaluate the transport of metals and loss of acidity from mine wastes as a function of time. Multi-acid digestion ICP-AES analyses, X-ray diffraction (XRD) mineral identification, total sulphur, and net acid potential (NAP) determinations were performed on the initial starting materials. Multiple leaching steps generally showed a 'flushing' effect, whereby elements loosely bound, presumably as water-soluble salts, were removed. Aluminum, Cd, Fe, Mg, Mn, Sr, Zn, and S showed decreasing concentration trends, whereas Cu concentrations showed initially decreasing trends, followed by increasing trends in later steps. Concentrations of Zn in the first leach step were independent of whole-sample Zn content. Lead and Ba concentrations consistently increased with each step, indicating that anglesite (PbSO4) and barite (BaSO4), respectively, were dissolving in successive leach steps. Comparison of Fe content with NAP resulted in a modest correlation. However, using the S analyses and XRD identification of sulphide minerals to apportion S amongst enargite, barite, anglesite/galena, and sphalerite, and assigning the remaining S to pyrite, provided a useful correlation between estimated pyrite content and NAP. Whole-sample mass loss correlated well with NAP, but individual elements' behaviors varied between positive correlation (e.g. Al, Fe, Mg), no apparent correlation (Ca, Cd, Pb, Zn), and negative correlation (Cu). Comparison of the summed titrated acidities of the leachates with the whole-sample NAP values yielded an estimate of the fraction of NAP consumed, and led to an estimate of the time it would take to consume the sample acidity by weathering. We estimate, on the basis of these experiments, the acidity in the upper 30 cm would be consumed in 200–1000 years. In addition, calculations suggest that the acidity would be depleted before the complete store of the metals Cu-Cd-Zn in these mine wastes would be released to the environment.

Multiple applications of the U.S. EPA 1312 leach procedure to mine waste from the animas watershed, SW Colorado

USGS Publications Warehouse

Fey, D.L.; Church, S.E.; Driscoll, R.L.; Adams, M.G.

2011-01-01

Eleven acid-sulphate and quartz-sericite-pyrite altered mine waste samples from the Animas River watershed in SW Colorado were subjected to a series of 5 to 6 successive leaches using the US EPA 1312 leach protocol to evaluate the transport of metals and loss of acidity from mine wastes as a function of time. Multi-acid digestion ICP-AES analyses, X-ray diffraction (XRD) mineral identification, total sulphur, and net acid potential (NAP) determinations were performed on the initial starting materials. Multiple leaching steps generally showed a 'flushing' effect, whereby elements loosely bound, presumably as water-soluble salts, were removed. Aluminum, Cd, Fe, Mg, Mn, Sr, Zn, and S showed decreasing concentration trends, whereas Cu concentrations showed initially decreasing trends, followed by increasing trends in later steps. Concentrations of Zn in the first leach step were independent of whole-sample Zn content. Lead and Ba concentrations consistently increased with each step, indicating that anglesite (PbSO4) and barite (BaSO4), respectively, were dissolving in successive leach steps. Comparison of Fe content with NAP resulted in a modest correlation. However, using the S analyses and XRD identification of sulphide minerals to apportion S amongst enargite, barite, anglesite/galena, and sphalerite, and assigning the remaining S to pyrite, provided a useful correlation between estimated pyrite content and NAP. Whole-sample mass loss correlated well with NAP, but individual elements' behaviors varied between positive correlation (e.g. Al, Fe, Mg), no apparent correlation (Ca, Cd, Pb, Zn), and negative correlation (Cu). Comparison of the summed titrated acidities of the leachates with the whole-sample NAP values yielded an estimate of the fraction of NAP consumed, and led to an estimate of the time it would take to consume the sample acidity by weathering. We estimate, on the basis of these experiments, the acidity in the upper 30 cm would be consumed in 200-1000 years. In addition, calculations suggest that the acidity would be depleted before the complete store of the metals Cu-Cd-Zn in these mine wastes would be released to the environment. ?? 2011 AAG/Geological Society of London.

The response of soil solution chemistry in European forests to decreasing acid deposition.

PubMed

Johnson, James; Graf Pannatier, Elisabeth; Carnicelli, Stefano; Cecchini, Guia; Clarke, Nicholas; Cools, Nathalie; Hansen, Karin; Meesenburg, Henning; Nieminen, Tiina M; Pihl-Karlsson, Gunilla; Titeux, Hugues; Vanguelova, Elena; Verstraeten, Arne; Vesterdal, Lars; Waldner, Peter; Jonard, Mathieu

2018-03-31

Acid deposition arising from sulphur (S) and nitrogen (N) emissions from fossil fuel combustion and agriculture has contributed to the acidification of terrestrial ecosystems in many regions globally. However, in Europe and North America, S deposition has greatly decreased in recent decades due to emissions controls. In this study, we assessed the response of soil solution chemistry in mineral horizons of European forests to these changes. Trends in pH, acid neutralizing capacity (ANC), major ions, total aluminium (Al tot ) and dissolved organic carbon were determined for the period 1995-2012. Plots with at least 10 years of observations from the ICP Forests monitoring network were used. Trends were assessed for the upper mineral soil (10-20 cm, 104 plots) and subsoil (40-80 cm, 162 plots). There was a large decrease in the concentration of sulphate (SO42-) in soil solution; over a 10-year period (2000-2010), SO42- decreased by 52% at 10-20 cm and 40% at 40-80 cm. Nitrate was unchanged at 10-20 cm but decreased at 40-80 cm. The decrease in acid anions was accompanied by a large and significant decrease in the concentration of the nutrient base cations: calcium, magnesium and potassium (Bc = Ca 2+  + Mg 2+  + K + ) and Al tot over the entire dataset. The response of soil solution acidity was nonuniform. At 10-20 cm, ANC increased in acid-sensitive soils (base saturation ≤10%) indicating a recovery, but ANC decreased in soils with base saturation >10%. At 40-80 cm, ANC remained unchanged in acid-sensitive soils (base saturation ≤20%, pHCaCl2 ≤ 4.5) and decreased in better-buffered soils (base saturation >20%, pHCaCl2 > 4.5). In addition, the molar ratio of Bc to Al tot either did not change or decreased. The results suggest a long-time lag between emission abatement and changes in soil solution acidity and underline the importance of long-term monitoring in evaluating ecosystem response to decreases in deposition. © 2018 John Wiley & Sons Ltd.

Possible role of Rhodotorula sp. in the formation of jarosite in the AMD environment of Muskau Arch, Poland

NASA Astrophysics Data System (ADS)

Jakus, Natalia; Chlebicki, Andrzej; Bożęcki, Piotr; Manecki, Maciej

2016-04-01

The Muskau Arch is situated in the west of Poland and in the east of Germany. This region is a belt formed by push and frontal moraines during the Middle-Polish (Riss) glaciation, especially during the Wartanian glaciation. The occurrence of glacier caused folding and forming the glacitectonic type of lignit deposits which were mined for over 150 years. Both open pit and underground mining methods has exposed metal sulfides (mainly pyrite) to air and water causing bio-oxidation. Due to this process the acidity of many reservoirs have increased significantly (pH values between 2 and 4). As a consequence of changes in the environment, new mineral phases precipitated from highly acid waters rich in, among others, various forms of Fe and S. Precipitation of ochreous minerals such as schwertmannite, goethite and jarosite was partly catalyzed by many various acidophilic and acid-tolerant microorganisms: bacteria, archaea and probably yeasts. Jarosite KFe33+(OH)6(SO4)2 can be precipitated both in abiotic conditions and as a by-product of the activity of living organisms. The example of biomineralization induced by fungi Purpureocillium lilacinum in similar AMD environment of Rio Tinto is reported (Oggerin et al, 2014). Recently, jarosite is also considered as a possible biosignature of life on Mars. The assessment of microbial participation in formation of jarosite is an elementary step in geomicrobiological and astrobiological research. Isolated by us Rhodotorula sp. is an unicellular pigmented yeast. Fungi from the genus Rhodotorula F.C. Harrison belong to Sporidiobolalas part of phylum Basidiomycota. They are common environmental inhabitants. Some species, known from Rio Tinto, can live in extreme acidic soils at pH of about 2 (Lopez-Archila et al, 2004). For the first time, authors isolated strain Rhodotorula sp. from surface precipitates in Ł ęknica region (Muskau Arch). This ochreous precipitate contains jarosite. The yeast might be an important factor in indirect enzymatic catalysis of the oxidation of pyrite. Jarosite precipitates from solution containing sulphate, possibly product of active enzymatic oxidation of sulphur compounds by Rhodotorula. As a result of this investigation a model of sulphur transformation mediated by Rhodotorula in AMD environment and its role in precipitation of jarosite was proposed. This work is partially funded by AGH research grant no 11.11.140.319. López-Archilla, A., González, A., Terrón, M., Amils, R. 2004. Ecological study of the fungal populations of the acidic Tinto River in southwestern Spain. Canadian Journal of Microbiology, 50 (11), 923-934. Oggerin, M., Rodriguez, N., del Moral, C., Amils, R. 2014. Fungal jarosite biomineralization in Rio Tinto. Research in Microbiology. 165, 719-725.

Nitrogen and phosphorus resorption in a neotropical rain forest of a nutrient-rich soil.

PubMed

Martínez-Sánchez, José Luis

2005-01-01

In tropical forests with nutrient-rich soil tree's nutrient resorption from senesced leaves has not always been observed to be low. Perhaps this lack of consistence is partly owing to the nutrient resorption methods used. The aim of the study was to analyse N and P resorption proficiency from tropical rain forest trees in a nutrient-rich soil. It was hypothesised that trees would exhibit low nutrient resorption in a nutrient-rich soil. The soil concentrations of total N and extractable P, among other physical and chemical characteristics, were analysed in 30 samples in the soil surface (10 cm) of three undisturbed forest plots at 'Estaci6n de Biologia Los Tuxtlas' on the east coast of Mexico (18 degrees 34' - 18 degrees 36' N, 95 degrees 04' - 95 degrees 09' W). N and P resorption proficiency were determined from senescing leaves in 11 dominant tree species. Nitrogen was analysed by microkjeldahl digestion with sulphuric acid and distilled with boric acid, and phosphorus was analysed by digestion with nitric acid and perchloric acid. Soil was rich in total N (0.50%, n = 30) and extractable P (4.11 microg g(-1) n = 30). As expected, trees showed incomplete N (1.13%, n = 11) and P (0.11%, n = 1) resorption. With a more accurate method of nutrient resorption assessment, it is possible to prove that a forest community with a nutrient-rich soil can have low levels of N and P resorption.

Enzymatic saccharification and lactic acid production from banana pseudo-stem through optimized pretreatment at lowest catalyst concentration

PubMed Central

Idrees, Muhammad; Adnan, Ahmad; Malik, Farnaz; Qureshi, Fahim Ashraf

2013-01-01

This work estimates the potential of banana pseudo-stem with high cellulosic content 42.2-63 %, for the production of fermentable sugars for lactic acid production through statistically optimized pretreatment method. To evaluate the catalyzed pretreatment efficiency of banana pseudo stem based on the enzymatic digestibility, Response Surface Methodology (RSM) was employed for the optimization of pretreatment temperature and time using lowest concentrations of H2SO4, NaOH, NaOH catalyzed Na2S and Na2SO3 that seemed to be significant variables with P<0.05. High F and R2 values and low p-value for hydrolysis yield indicated the model predictability. The optimized condition for NaOH was determined to be conc. 1 %, temperature 130 oC for 2.6 hr; Na2S; conc. 1 %, temperature 130 oC for 2.29 hr; Na2SO3; conc. 1 %, temperature 130 oC for 2.41 hr and H2SO4; conc. 1 %, temperature 129.45 oC for 2.18 hr, produced 84.91 %, 85.23 %, 81.2 % and 76.02 % hydrolysis yield, respectively. Sulphuric acid provided 33+1 gL-1 reducing sugars in pretreatment step along with 38+0.5 gL-1 during enzymatic hydrolysis. Separate hydrolysis and fermentation of resulting sugars showed that the conversion of glucans into lactic acid reached 92 % of the theoretical yield of glucose. PMID:26966423

A new method for the extraction and purification of K99 pili from enterotoxigenic Escherichia coli and their characterization.

PubMed Central

Altmann, K; Pyliotis, N A; Mukkur, T K

1982-01-01

It was found that K99 pili from enterotoxigenic Escherichia coli (of bovine origin) could be extracted by treatment with 3M-KSCN solution. The K99 pili were purified by preparative isoelectric focusing to apparent homogeneity as judged by the presence of a single band on sodium dodecyl sulphate/polyacrylamide-gel electrophoresis; the molecular weight of this component was calculated to be 12 600 +/- 300. This indicated that the K99 pili were composed of a single subunit. On analytical ultracentrifugation, a single boundary with an s20,w of 12.2 S at a concentration of 0.42 mg/ml was observed. The average length of purified pili at zero concentration was approx. 160 nm and the diameter was 7.4 +/- 0.6 nm. Amino acid analysis of the purified K99 pili revealed that sulphur-containing amino acids, cysteine and methionine, were absent. Aromatic amino acids, phenylalanine and tyrosine, previously reported to be absent [Isaacson (1977) Infect. Immun. 15. 272-279], constituted 7.14% of the total amino acid residues present. On immunoelectrophoresis, purified K99 pili migrated towards the cathode and caused mannose-resistant haemagglutination of horse, but not of sheep or guinea-pig, red blood cells. Pili from enterotoxigenic E. coli of porcine and human origin and from another bacterial species, namely Fusiformis nodosus, could also be extracted by the treatment of respective micro-organisms with 3 M-KSCN. Images PLATE 1 Fig. 3. Fig. 5. PMID:6124240

Induction of simultaneous and sequential malolactic fermentation in durian wine.

PubMed

Taniasuri, Fransisca; Lee, Pin-Rou; Liu, Shao-Quan

2016-08-02

This study represented for the first time the impact of malolactic fermentation (MLF) induced by Oenococcus oeni and its inoculation strategies (simultaneous vs. sequential) on the fermentation performance as well as aroma compound profile of durian wine. There was no negative impact of simultaneous inoculation of O. oeni and Saccharomyces cerevisiae on the growth and fermentation kinetics of S. cerevisiae as compared to sequential fermentation. Simultaneous MLF did not lead to an excessive increase in volatile acidity as compared to sequential MLF. The kinetic changes of organic acids (i.e. malic, lactic, succinic, acetic and α-ketoglutaric acids) varied with simultaneous and sequential MLF relative to yeast alone. MLF, regardless of inoculation mode, resulted in higher production of fermentation-derived volatiles as compared to control (alcoholic fermentation only), including esters, volatile fatty acids, and terpenes, except for higher alcohols. Most indigenous volatile sulphur compounds in durian were decreased to trace levels with little differences among the control, simultaneous and sequential MLF. Among the different wines, the wine with simultaneous MLF had higher concentrations of terpenes and acetate esters while sequential MLF had increased concentrations of medium- and long-chain ethyl esters. Relative to alcoholic fermentation only, both simultaneous and sequential MLF reduced acetaldehyde substantially with sequential MLF being more effective. These findings illustrate that MLF is an effective and novel way of modulating the volatile and aroma compound profile of durian wine. Copyright © 2016 Elsevier B.V. All rights reserved.

The structure and vibrational frequencies of nitric acid hydrates crystals

NASA Astrophysics Data System (ADS)

Escribano, R.; Fernández, D.; Herrero, V. J.; Maté, B.; Medialdea, A.; Moreno, M. A.; Ortega, I. K.

The relevance of nitric acid hydrates in stratospheric processes has prompted a large number of investigations on the structure and physicochemical properties of these species. We are carrying out in our lab a study on the spectroscopy of crystals of nitric acid and the mono-, di- and trihydrates, NAM, NAD and NAT, respectively, as a first step to addressing more elaborate systems, like binary or ternary mixtures of nitric acid with water, sulphuric acid or halogen compounds of atmospheric interest. Our work consists of a theoretical part, which deals with the determination of the crystalline structure of the species and the prediction of their infrared spectra, and of an experimental part, in which we record Reflection-Absorption infrared spectra of samples prepared under controlled conditions of low pressure and temperature. The theoretical calculations are carried out with the recently developed program SIESTA (acronym for Spanish Initiative for Electronic Simulation of Thousands of Atoms), which allows the ab initio study of periodic systems of large size, by a method that scales linearly in time and computer memory requirements with the number of atoms in a simulation cell. The experimental work is performed on a cryostat cell built in our laboratory. The cell has a number of inlet devices to allow gases to be expanded within, and infrared radiation from a FTIR spectrometer to enter and exit. Films of the species under study are formed by condensing the appropriate gases or mixtures of them on a polished surface of gold or aluminium, whose temperature is controlled externally and can be varied between 80 and 325 K. Examples of experimental and predicted spectra will be presented at the meeting, with a discussion on the proposed assignments.

Nickel-cadmium batteries: effect of electrode phase composition on acid leaching process.

PubMed

Nogueira, C A; Margarido, F

2012-01-01

At the end of their life, Ni-Cd batteries cause a number of environmental problems because of the heavy metals they contain. Because of this, recycling of Ni-Cd batteries has been carried out by dedicated companies using, normally, pyrometallurgical technologies. As an alternative, hydrometallurgical processes have been developed based on leaching operations using several types of leachants. The effect of factors like temperature, acid concentration, reaction time, stirring speed and grinding of material on the leaching yields of metals contained in anodic and cathodic materials (nickel, cadmium and cobalt) using sulphuric acid, is herein explained based on the structural composition of the electrode materials. The nickel, cobalt and cadmium hydroxide phases, even with a small reaction time (less than 15 minutes) and low temperature (50 degrees C) and acid concentration (1.1 M H2SO4), were efficiently leached. However, leaching of the nickel metallic phase was more difficult, requiring higher values of temperature, acid concentration and reaction time (e.g. 85 degrees C, 1.1 M H2SO4 and 5 h, respectively) in order to obtain a good leaching efficiency for anodic and cathodic materials (70% and 93% respectively). The stirring speed was not significant, whereas the grinding of electrode materials seems to promote the compaction of particles, which appears to be critical in the leaching of Ni degrees. These results allowed the identification and understanding of the relationship between the structural composition of electrode materials and the most important factors that affect the H2SO4 leaching of spent Ni-Cd battery electrodes, in order to obtain better metal-recovery efficiency.

Development and evaluation of a full-scale spray scrubber for ammonia recovery and production of nitrogen fertilizer at poultry facilities.

PubMed

Hadlocon, Lara Jane S; Manuzon, Roderick B; Zhao, Lingying

2015-01-01

Significant ammonia emissions from animal facilities need to be controlled due to its negative impacts on human health and the environment. The use of acid spray scrubber is promising, as it simultaneously mitigates and recovers ammonia emission for fertilizer. Its low pressure drop contribution on axial fans makes it applicable on US farms. This study develops a full-scale acid spray scrubber to recover ammonia emissions from commercial poultry facilities and produce nitrogen fertilizer. The scrubber performance and economic feasibility were evaluated at a commercial poultry manure composting facility that released ammonia from exhaust fans with concentrations of 66-278 ppmv and total emission rate of 96,143 kg yr(-1). The scrubber consisted of 15 spray scrubber modules, each equipped with three full-cone nozzles that used dilute sulphuric acid as the medium. Each nozzle was operated at 0.59 MPa with a droplet size of 113 μm and liquid flow rate of 1.8 L min(-1). The scrubber was installed with a 1.3-m exhaust fan and field tested in four seasons. Results showed that the scrubber achieved high NH3 removal efficiencies (71-81%) and low pressure drop (<25 Pa). Estimated water and acid losses are 0.9 and 0.04 ml m(-3) air treated, respectively. Power consumption rate was between 89.48 and 107.48 kWh d(-1). The scrubber effluents containing 22-36% (m/v) ammonium sulphate are comparable to the commercial-grade nitrogen fertilizer. Preliminary economic analysis indicated that the break-even time is one year. This study demonstrates that acid spray scrubbers can economically and effectively recover NH3 from animal facilities for fertilizer.

Effects of five years of frequent N additions, with or without acidity, on the growth and below-ground dynamics of a young Sitka spruce stand growing on an acid peat: implications for sustainability

NASA Astrophysics Data System (ADS)

Stutter, M. I.; Alam, M. S.; Langan, S. J.; Woodin, S. J.; Smart, R. P.; Cresser, M. S.

2004-06-01

An experiment comparing effects of sulphuric acid and reduced N deposition on soil water quality and on chemical and physical growth indicators for forest ecosystems is described. Six H2SO4 and (NH4)2SO4 treatment loads, from 0 - 44 and 0 - 25 kmolc ha-1 yr-1, respectively, were applied to outdoor microcosms of Pinus sylvestris seedlings in 3 acid to intermediate upland soils (calc-silicate, quartzite and granite) for 2 years. Different soil types responded similarly to H2SO4 loads, resulting in decreased leachate pH, but differently to reduced N inputs. In microcosms of calc-silicate soil, nitrification of NH4 resulted in lower pH and higher cation leaching than in acid treatments. By contrast, in quartzite and granite soils, (NH4)2SO4 promoted direct cation leaching, although leachate pH increased. The results highlighted the importance of soil composition on the nature of the cations leached, the SO4 adsorption capacities and microbial N transformations. Greater seedling growth on calc-silicate soils under both treatment types was related to sustained nutrient availability. Reductions in foliar P and Mg with higher N treatments were observed for seedlings in the calc-silicate soil. There were few treatment effects on quartzite and granite microcosm tree seedlings since P limitation precluded seedling growth responses to treatments. Hence, any benefits of N deposition to seedlings on quartzite and granite soils appeared limited by availability of co-nutrients, exacerbated by rapid depletion of soil exchangeable base cations.

Fabrication of ultra thin anodic aluminium oxide membranes by low anodization voltages

NASA Astrophysics Data System (ADS)

Pastore, I.; Poplausks, R.; Apsite, I.; Pastare, I.; Lombardi, F.; Erts, D.

2011-06-01

Formation of ultrathin anodised aluminium oxide (AAO) membranes with high aspect ratio by Al anodization in sulphuric and oxalic acids at low potentials was investigated. Low anodization potentials ensure slow electrochemical reaction speeds and formation of AAO membranes with pore diameter and thickness below 20 nm and 70 nm respectively. Minimum time necessary for formation of continuous AAO membranes was determined. AAO membrane pore surface was covered with polymer Paraloid B72TM to transport it to the selected substrate. The fabricated ultra thin AAO membranes could be used to fabricate nanodot arrays on different surfaces.

[Blood levels of homocysteine by high pressure liquid chromatography and comparison with two other techniques].

PubMed

Ceppa, F; Drouillard, I; Chianea, D; Burnat, P; Perrier, F; Vaillant, C; El Jahiri, Y

1999-01-01

Cardio-vascular diseases are the most common cause of death in industrialized countries. A new marker has emerged among offending risk factors in the past few years: homocysteine. This sulphured amino-acid is an important intermediate in transsulphuration and remethylation reactions of methionine's metabolism. We proposed to evaluate a home made method of determination for this parameter by high performance liquid chromatography (HPLC) and to compare it to fluorescence polarization immunoassay technique (FPIA) and to gaz phase chromatography (CG-SM). This method associated with good sensibility and precision remain much less expensive than FPIA technique.

The anaesthesia of fish by high carbon-dioxide concentrations

USGS Publications Warehouse

1942-01-01

A practical and economical method for anaesthetizing adult salmon and steelhead trout in the fish trucks used in the Grand Coulee fish salvage program is described. The method consists in generating a predetermined carbon-dioxide concentration in the 1000-gallon tanks of the trucks through the successive addition of predissolved sodium bicarbonate and dilute sulphuric acid in proper quantities. Carbon-dioxide anaesthesia effectively solved the acute problem of species segregation in the fish salvage program and, with minor modifications, could be used with equal success in certain hatchery operations necessitating the handling of large fish.

Molecular imaging in neuroendocrine tumors: molecular uptake mechanisms and clinical results.

PubMed

Koopmans, Klaas P; Neels, Oliver N; Kema, Ido P; Elsinga, Philip H; Links, Thera P; de Vries, Elisabeth G E; Jager, Pieter L

2009-09-01

Neuroendocrine tumors can originate almost everywhere in the body and consist of a great variety of subtypes. This paper focuses on molecular imaging methods using nuclear medicine techniques in neuroendocrine tumors, coupling molecular uptake mechanisms of radiotracers with clinical results. A non-systematic review is presented on receptor based and metabolic imaging methods. Receptor-based imaging covers the molecular backgrounds of somatostatin, vaso-intestinal peptide (VIP), bombesin and cholecystokinin (CCK) receptors and their link with nuclear imaging. Imaging methods based on specific metabolic properties include meta-iodo-benzylguanide (MIBG) and dimercapto-sulphuric acid (DMSA-V) scintigraphy as well as more modern positron emission tomography (PET)-based methods using radio-labeled analogues of amino acids, glucose, dihydroxyphenylalanine (DOPA), dopamine and tryptophan. Diagnostic sensitivities are presented for each imaging method and for each neuroendocrine tumor subtype. Finally, a Forest plot analysis of diagnostic performance is presented for each tumor type in order to provide a comprehensive overview for clinical use.

A 3D Microfluidic Chip for Electrochemical Detection of Hydrolysed Nucleic Bases by a Modified Glassy Carbon Electrode

PubMed Central

Vlachova, Jana; Tmejova, Katerina; Kopel, Pavel; Korabik, Maria; Zitka, Jan; Hynek, David; Kynicky, Jindrich; Adam, Vojtech; Kizek, Rene

2015-01-01

Modification of carbon materials, especially graphene-based materials, has wide applications in electrochemical detection such as electrochemical lab-on-chip devices. A glassy carbon electrode (GCE) modified with chemically alternated graphene oxide was used as a working electrode (glassy carbon modified by graphene oxide with sulphur containing compounds and Nafion) for detection of nucleobases in hydrolysed samples (HCl pH = 2.9, 100 °C, 1 h, neutralization by NaOH). It was found out that modification, especially with trithiocyanuric acid, increased the sensitivity of detection in comparison with pure GCE. All processes were finally implemented in a microfluidic chip formed with a 3D printer by fused deposition modelling technology. As a material for chip fabrication, acrylonitrile butadiene styrene was chosen because of its mechanical and chemical stability. The chip contained the one chamber for the hydrolysis of the nucleic acid and another for the electrochemical detection by the modified GCE. This chamber was fabricated to allow for replacement of the GCE. PMID:25621613

Biochemical and technological studies on the production of isolated guar protein.

PubMed

Khalil, M M

2001-02-01

Guar seeds contain 32% crude protein. Therefore, attempts were made to prepare protein isolates from guar seed flour (GSF) by extraction in different media (distilled water, salt solution, alkali solution alone or in combination) followed by a precipitation at acid pH. From the four technologies adopted, mixed salt-alkali solution was found to be the most satisfactory for extraction of protein from GSF. The highest amount of product was obtained in the mixed technology along with the highest amount of protein (87.5%). Protein isolates were also nutritionally evaluated following well-established rat bioassay procedures in a comparative study with casein as standard. The protein isolates are rich in lysine but poor in sulphur-containing amino acids such as methionine and cysteine. Protein isolates obtained by mixed salt-alkali solution showed high water and oil absorption as well as good emulsifying and foaming stability. The results indicate that protein isolates can be used as a supplementary source of protein in different food industries.

Durability of Bricks Coated with Red mud Based Geopolymer Paste

NASA Astrophysics Data System (ADS)

Singh, Smita; Basavanagowda, S. N.; Aswath, M. U.; Ranganath, R. V.

2016-09-01

The present study is undertaken to assess the durability of concrete blocks coated with red mud - fly ash based geopolymer paste. Concrete blocks of size 200 x 200 x 100mm were coated with geopolymer paste synthesized by varying the percentages of red mud and fly ash. Uncoated concrete blocks were also tested for the durability for comparison. In thermal resistance test, the blocks were subjected to 600°C for an hour whereas in acid resistance test, they were kept in 5% sulphuric acid solution for 4 weeks. The specimens were thereafter studied for surface degradation, strength loss and weight loss. Pastes with red mud percentage greater than 50% developed lot of shrinkage cracks. The blocks coated with 30% and 50% red mud paste showed better durability than the other blocks. The use of blocks coated with red mud - fly ash geopolymer paste improves the aesthetics, eliminates the use of plaster and improves the durability of the structure.

Determination of nitrites in water by in-electrode coulometric titration in reticulated vitreous carbon electrode.

PubMed

Lenghartova, Katarina; Lauko, Lukas; Cachob, Frantisek; Beinrohr, Ernest

2015-01-01

Nitrite in water samples was determined by in-electrode coulometric titration in a reticulated vitreous carbon (RVC) electrode of 100 ppi porosity. The sample was mixed with dilute sulphuric acid and sodium sulphate, filled into a flow cell with the porous electrode and nitrite was oxidised to nitrate by constant current of 5 µA at which the potential of the electrode was monitored. The limits of detection and quantification were found to be 0.4 and 1.2 µg/L, respectively. The repeatability and reproducibility were 2.2 % and 2.6 %, respectively. The bias at 100 µg/L were found to be 0.3 %. The duration of the measurement is 2-3 min depending on the nitrite concentration. There were few interferences only, neutral and cationic surfactants decreased and increased slightly the signal, respectively. Humic acids above 30 mg/L increased the signal by 10 %. Drinking and surface water samples were analysed and the results matched well those from the photometric method.

A 3D microfluidic chip for electrochemical detection of hydrolysed nucleic bases by a modified glassy carbon electrode.

PubMed

Vlachova, Jana; Tmejova, Katerina; Kopel, Pavel; Korabik, Maria; Zitka, Jan; Hynek, David; Kynicky, Jindrich; Adam, Vojtech; Kizek, Rene

2015-01-22

Modification of carbon materials, especially graphene-based materials, has wide applications in electrochemical detection such as electrochemical lab-on-chip devices. A glassy carbon electrode (GCE) modified with chemically alternated graphene oxide was used as a working electrode (glassy carbon modified by graphene oxide with sulphur containing compounds and Nafion) for detection of nucleobases in hydrolysed samples (HCl pH = 2.9, 100 °C, 1 h, neutralization by NaOH). It was found out that modification, especially with trithiocyanuric acid, increased the sensitivity of detection in comparison with pure GCE. All processes were finally implemented in a microfluidic chip formed with a 3D printer by fused deposition modelling technology. As a material for chip fabrication, acrylonitrile butadiene styrene was chosen because of its mechanical and chemical stability. The chip contained the one chamber for the hydrolysis of the nucleic acid and another for the electrochemical detection by the modified GCE. This chamber was fabricated to allow for replacement of the GCE.

The Lifetime of DMS in Northern Latitudes: Results from Four Shipboard Experiments

NASA Astrophysics Data System (ADS)

Norman, A.; Wadleigh, M. A.; Zaganescu, C.; Burridge, C.; Eaton, S.; Seguin, M.; Siauw, A.; Sharma, S.; Levasseur, M.; Scarratt, M.; Michaud, S.; Leaitch, R.; Blanchet, J.; Steiner, N.; McFarlane, N.

2006-12-01

The lifetime of dimethylsulfide (DMS) is usually referred to as being a day or more and is typically based on oxidation by OH and nitrate. However, the definition of DMS lifetime is not simply academic. It is an essential component for climate models attempting to estimate the effect of DMS oxidation as a feedback to global warming: an effect that is of increasing importance at high latitudes. The relevance of DMS oxidation by halogens, which are present at concentrations below detection limits of most current instrumentation, has largely been left as a modeling exercise. However, recent results from studies incorporating DMS flux from surface water and atmospheric measurements at mid to high latitudes permit a closer examination of the assumptions surrounding oxidation. A unique series of atmospheric and ocean DMS measurements were performed as part of Canadian Surface Ocean Lower Atmosphere Study (C-SOLAS) in 2002 and 2003 to clarify new aerosol formation. Month-long shipboard campaigns were conducted in the summer of 2002 over the North Pacific and a seasonal study with three campaigns was performed in 2003 above the NW Atlantic. Land- and ship-based measurements of the oxidation products sulphur dioxide, aerosol sulphate, and methane sulfonic acid provide a larger context in which to place the results. Sulphur isotope apportionment was used to quantify the contribution of DMS to sulphate and sulphur dioxide to link gas concentrations with biogenic aerosol formation.

Remediation of soils contaminated with particulate depleted uranium by multi stage chemical extraction.

PubMed

Crean, Daniel E; Livens, Francis R; Sajih, Mustafa; Stennett, Martin C; Grolimund, Daniel; Borca, Camelia N; Hyatt, Neil C

2013-12-15

Contamination of soils with depleted uranium (DU) from munitions firing occurs in conflict zones and at test firing sites. This study reports the development of a chemical extraction methodology for remediation of soils contaminated with particulate DU. Uranium phases in soils from two sites at a UK firing range, MOD Eskmeals, were characterised by electron microscopy and sequential extraction. Uranium rich particles with characteristic spherical morphologies were observed in soils, consistent with other instances of DU munitions contamination. Batch extraction efficiencies for aqueous ammonium bicarbonate (42-50% total DU extracted), citric acid (30-42% total DU) and sulphuric acid (13-19% total DU) were evaluated. Characterisation of residues from bicarbonate-treated soils by synchrotron microfocus X-ray diffraction and X-ray absorption spectroscopy revealed partially leached U(IV)-oxide particles and some secondary uranyl-carbonate phases. Based on these data, a multi-stage extraction scheme was developed utilising leaching in ammonium bicarbonate followed by citric acid to dissolve secondary carbonate species. Site specific U extraction was improved to 68-87% total U by the application of this methodology, potentially providing a route to efficient DU decontamination using low cost, environmentally compatible reagents. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

A novel non-dairy beverage from durian pulp fermented with selected probiotics and yeast.

PubMed

Lu, Yuyun; Putra, Satya Dwi; Liu, Shao-Quan

2018-01-16

This study investigated the effects of sequential inoculation (Seq-I) of Bifidobacterium animalis subsp. lactis or Lactobacillus casei with yeast Williopsis saturnus on durian pulp fermentation. Seq-I of W. saturnus following B. animalis subsp. lactis did not bring about any significant differences compared to the B. animalis subsp. lactis monoculture due to the sharp early death of W. saturnus soon after inoculation. However, Seq-I of W. saturnus significantly enhanced the survival of L. casei and improved the utilization of fructose and glucose compared to L. casei monoculture. In addition, there were significant differences in the metabolism of organic acids especially for lactic acid and succinic acid. Furthermore, Seq-I produced significantly higher levels of volatile compounds including alcohols (ethanol and 2-phenylethyl alcohol) and acetate esters (2-phenylethyl acetate, isoamyl acetate and ethyl acetate), which would positively contribute to the flavour notes. Although the initial volatile sulphur compounds were reduced to trace levels after fermentation, but the durian odour still remained. This study suggests that the use of probiotics and W. saturnus to ferment durian pulp could act as a potential avenue to develop a novel non-dairy durian-based functional beverage to deliver probiotics. Copyright © 2017 Elsevier B.V. All rights reserved.

Study concerning the recovery of zinc and manganese from spent batteries by hydrometallurgical processes.

PubMed

Buzatu, Traian; Popescu, Gabriela; Birloaga, Ionela; Săceanu, Simona

2013-03-01

Used batteries contain numerous metals in high concentrations and if not disposed of with proper care, they can negatively affect our environment. These metals represent 83% of all spent batteries and therefore it is important to recover metals such as Zn and Mn, and reuse them for the production of new batteries. The recovery of Zn and Mn from used batteries, in particular from Zn-C and alkaline ones has been researched using hydrometallurgical methods. After comminution and classification of elemental components, the electrode paste resulting from these processes was treated by chemical leaching. Prior to the leaching process the electrode paste has been subjected to two washing steps, in order to remove the potassium, which is an inconvenient element in this type of processes. To simultaneously extract Zn and Mn from this paste, the leaching method in alkaline medium (NaOH solution) and acid medium (sulphuric acid solution) was used. Also, to determine the efficiency of extraction of Zn and Mn from used batteries, the following variables were studied: reagents concentration, S/L ratio, temperature, time. The best results for extraction yield of Zn and Mn were obtained under acid leaching conditions (2M H2SO4, 1h, 80°C). Copyright © 2012 Elsevier Ltd. All rights reserved.

Recovery of NORM from scales generated by oil extraction.

PubMed

Al Attar, Lina; Safia, Bassam; Ghani, Basem Abdul; Al Abdulah, Jamal

2016-03-01

Scales, containing naturally occurring radioactive materials (NORM), are a major problem in oil production that lead to costly remediation and disposal programmes. In view of environmental protection, radio and chemical characterisation is an essential step prior to waste treatment. This study focuses on developing of a protocol to recover (226)Ra and (210)Pb from scales produced by petroleum industry. X-ray diffractograms of the scales indicated the presence of barite-strontium (Ba0.75Sr0.25SO4) and hokutolite (Ba0.69Pb0.31SO4) as main minerals. Quartz, galena and Ca2Al2SiO6(OH)2 or sphalerite and iron oxide were found in minor quantities. Incineration to 600 °C followed by enclosed-digestion and acid-treatment gave complete digestion. Using (133)Ba and (210)Pb tracers as internal standards gave recovery ranged 87-91% for (226)Ra and ca. 100% for (210)Pb. Radium was finally dissolved in concentrated sulphuric acid, while (210)Pb dissolved in the former solution as well as in 8 M nitric acid. Dissolving the scales would provide better estimation of their radionuclides contents, facilitate the determination of their chemical composition, and make it possible to recycle NORM wastes in terms of radionuclides production. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash.

PubMed

Kuboňová, L; Langová, Š; Nowak, B; Winter, F

2013-11-01

Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be a potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050°C and in a muffle oven at temperatures from 500 to 1200°C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel. Copyright © 2013 Elsevier Ltd. All rights reserved.

Seasonal variation and mixing behaviour of glutathione, thioacetamide and fulvic acids in a temperate macrotidal estuary (Aulne, NW France)

NASA Astrophysics Data System (ADS)

Marie, Lauriane; Pernet-Coudrier, Benoît; Waeles, Matthieu; Riso, Ricardo

2017-01-01

Fulvic acids and two dissolved reduced sulphur substances (RSS) were analysed for one year along the whole salinity gradient in the Aulne estuary (north-western France) using differential pulse cathodic stripping voltammetry. Concentrations of glutathione-like (GSH-like), thioacetamide-like (TA-like) and fulvic acid-like (FA-like) compounds ranged from 0.2 to 38 nmol L-1, from 0.02 to 6.6 μmol L-1 and from 0.1 to 4 mgC L-1, respectively. Our results indicated primarily allochthonous-continental sources for all three compounds. The behaviour of GSH-like compounds along the salinity gradient was globally conservative, with minor losses (<25%), possibly limited due to metal complexation. TA-like compounds generally displayed non-conservative behaviour with important removals. In terms of the TA-like budget, losses were counterbalanced by exceptional inputs occurring in the flood period (February). FA-like compounds were intensely degraded (∼50%) in the last section of the river and then behaved conservatively in the estuary. The annual flux of FA-like compounds to coastal waters was 2800 ± 600 tC. This flux was mainly (74%) delivered during the high discharge period, in accordance with its known pedogenic origin.

Synthesis of Biodiesel in Batch and Packed-Bed Reactors Using Powdered and Granular Sugar Catalyst

NASA Astrophysics Data System (ADS)

Janaun, J.; Lim, P. M.; Balan, W. S.; Yaser, A. Z.; Chong, K. P.

2017-06-01

Increasing world production of palm oil warrants effective utilization of its waste. In particular, conversion of waste cooking oil into biodiesel has obtained global interest because of renewable energy need and reduction of CO2 emission. In this study, oleic acid used as a model compound for waste cooking oil conversion using esterification reaction catalysed by sugar catalyst (SC) in powdered (P-SC) and granular (G-SC) forms. The catalysts were synthesized via incomplete carbonization of D-glucose followed by functionalization with concentrated sulphuric acid. Catalysts characterizations were done for their physical and chemical properties using modern tools. Batch and packed-bed reactor systems were used to evaluate the reactivity of the catalysts. The results showed that G-SC had slightly higher total acidity and more porous than P-SC. The experimental conditions for batch reaction were temperature of 60°C, molar ratio of 1:20 (Oleic Acid:Methanol) and 2 wt. catalyst with respect to oleic acid. The results showed the maximum oleic acid conversion using G-SC and P-SC were 52 and 48, respectively. Whereas, the continuous reaction with varying feed flow rate as a function of retention time was studied by using 3 g of P-SC in 60 °C and 1:20 molar ratio in a packed-bed reactor. The results showed that a longer retention time which was 6.48 min and feed flow rate 1.38 ml/min, achieved higher average conversion of 9.9 and decreased with further increasing flow rate. G-SC showed a better average conversion of 10.8 at lowest feed flow rate of 1.38 ml/min in continuous reaction experiments. In a broader perspective, large scale continuous biodiesel production is feasible using granular over powdered catalyst mainly due to it lower pressure drop.

Permeability of hair to cadmium, copper and lead in five species of terrestrial mammals and implications in biomonitoring.

PubMed

Rendón-Lugo, A N; Santiago, P; Puente-Lee, I; León-Paniagua, L

2017-11-18

The capacity of mammal hair to absorb toxic metals and its utility in biomonitoring has been broadly studied. Though these metal-binding properties has generally been attributed to the sulphur contained in cysteine, an amino acid that forms part of keratin, there are not many experimental studies that analyze the role of sulphur in the external deposition of potentially toxic metallic elements in order to better understand the potential of hair in biomonitoring and generate better tools for differentiating between internal and external deposition of contaminants. In this study, an experimental analysis is carried out using a scanning electron microscope on hairs of five terrestrial mammal species (Peromyscus furvus, P. maniculatus, Glossophaga soricina, Artibeus jamaicensis and Marmosa mexicana) treated with cadmium, copper and lead salts. We quantified absorbed metals as well as natural elements of the hair by energy dispersive X-ray spectroscopy (EDS) to analyze using simple statistics the role of sulphur in the absorption Cd, Cu and Pb. Given the lack of studies comparing the mechanisms of deposition of metal elements among different orders of Class Mammalia, external morphology was considered to be an important factor in the deposition of metallic particles of Cd, Cu and Pb. Bat species (Glossophaga soricina, Artibeus jamaicensis) showed a high concentration of particles in their scales, however, no between-species differences in metal absorption were observed, and during the exogenous deposition metal particles do not permeate the medulla. These results suggest that the sulphur in hair itself cannot bind metals to hair cuticle and that hair absorption capacity depends on a variety of factors such as aspects of hair morphology.

The comparative metabolism of 2,6-dichlorothiobenzamide (prefix) and 2,6-dichlorobenzonitrile in the dog and rat

PubMed Central

Griffiths, M. H.; Moss, J. A.; Rose, J. A.; Hathway, D. E.

1966-01-01

1. A single oral dose of either [14C]Prefix or 2,6-dichlorobenzo[14C]nitrile to rats is almost entirely eliminated in 4 days: 84·8–100·5% of 14C from [14C]Prefix is excreted, 67·3–79·7% in the urine, and 85·8–97·2% of 14C from 2,6-dichlorobenzo-[14C]nitrile is excreted, 72·3–80·7% in the urine. Only 0·37±0·03% of the dose of [14C]Prefix and 0·25±0·03% of the dose of 2,6-dichlorobenzo[14C]nitrile are present in the carcass plus viscera after removal of the gut. Rats do not show sex differences in the pattern of elimination of the respective metabolites of the two herbicides. The rates of elimination of 14C from the two compounds in the 24hr. and 48hr. urines are not significantly different (P >0·05) from one another. 2. After oral administration to dogs, 85·9–106·1% of 14C from [14C]Prefix is excreted, 66·6–80·9% in the urine, and 86·8–92·5% of 14C from 2,6-dichlorobenzo[14C]nitrile is excreted, 60·0–70·1% in the urine. Dogs do not show sex differences in the pattern of eliminating the metabolites of either Prefix or 2,6-dichlorobenzonitrile. 3. Dogs and rats do not show species differences in the patterns of elimination of the two herbicides. 4. Prefix and 2,6-dichlorobenzonitrile are completely metabolized; unchanged Prefix and 2,6-dichlorobenzonitrile are absent from the urine and faeces, and from the carcasses when elimination is complete. In the hydrolysed urine of rats dosed with either [14C]Prefix or 2,6-dichlorobenzo[14C]nitrile, 2,6-dichloro-3-hydroxybenzonitrile accounts for approx. 42% of the 14C, a further 10–11% is accounted for by 2,6-dichlorobenzamide, 2,6-dichlorobenzoic acid, 2,6-dichloro-3- and -4-hydroxybenzoic acid and 2,6-dichloro-4-hydroxybenzonitrile collectively, and 25–30% by six polar constituents, of which two are sulphur-containing amino acids. 5. In the unhydrolysed urines of rats dosed with either [14C]Prefix or 2,6-dichlorobenzo[14C]nitrile, there are present free 2,6-dichloro-3- and -4-hydroxybenzonitrile, their glucuronide conjugates, ester glucuronides of the principal aromatic acids that are present in the hydrolysed urines, and two sulphur-containing metabolites analogous to mercapturic acids or premercapturic acids. 6. Prefix is thus extensively transformed into 2,6-dichlorobenzonitrile: R·CS·NH2→R·CN+H2S, where R=C6H3Cl2. However, the competitive reaction: R·CS·NH2+H2O→R·CO·NH2+H2S takes place to a very limited extent. PMID:5911525

Workplace exposures and oesophageal cancer

PubMed Central

Parent, M.; Siemiatycki, J.; Fritschi, L.

2000-01-01

OBJECTIVES—To describe the relation between oesophageal cancer and many occupational circumstances with data from a population based case-control study.
METHODS—Cases were 99 histologically confirmed incident cases of cancer of the oesophagus, 63 of which were squamous cell carcinomas. Various control groups were available; for the present analysis a group was used that comprised 533 population controls and 533 patients with other types of cancer. Detailed job histories were elicited from all subjects and were translated by a team of chemists and hygienists for evidence of exposure to 294 occupational agents. Based on preliminary results and a review of literature, a set of 35 occupational agents and 19 occupations and industry titles were selected for this analysis. Logistic regression analyses were adjusted for age, birthplace, education, respondent (self or proxy), smoking, alcohol, and β-carotene intake.
RESULTS—Sulphuric acid and carbon black showed the strongest evidence of an association with oesophageal cancer, particularly squamous cell carcinoma. Other substances showed excess risks, but the evidence was more equivocal—namely chrysotile asbestos, alumina, mineral spirits, toluene, synthetic adhesives, other paints and varnishes, iron compounds, and mild steel dust. There was considerable overlap in occupational exposure patterns and results for some of these substances may be mutually confounded. None of the occupations or industry titles showed a clear excess risk; the strongest hints were for warehouse workers, food services workers, and workers from the miscellaneous food industry.
CONCLUSIONS—The data provide some support for an association between oesophageal cancer and a handful of occupational exposures, particularly sulphuric acid and carbon black. Many of the associations found have never been examined before and warrant further investigation.


Keywords: oesophageal cancer; occupational exposures; occupations PMID:10769298

[Metabolism of carbohydrates in the cells of green sulphur bacteria Chlorobium limicola Ya-2002].

PubMed

Horishnyĭ, M B; Hudz', S P; Hnatush, S O

2009-01-01

The nature of carbohydrates that accumulate in the cells of photosynthetic green sulphur bacteria of Chlorobium limicola Ya-2002 has been investigated. It is shown by infra-red spectrometry, that carbohydrates accumulated in the cells of bacteria are identical (by 90-95%) to glycogen of the bull liver. Exogenous glucose, saccharose, maltose, did not stimulate formation of glycogen. Growth of glycogen level in the cells of bacteria was observed at addition of acetate or piruvate in the conditions of bacteria cultivation in the light and in the presence CO2 and H2S in the environment. Washed cells of C. limicola Ya-2002 did not use glucose of the environment neither in the conditions of illumination nor in darkness, however acetate and piruvate are actively used in the light. During incubation of the washed cells in darkness the level of glycogen fell down approximately three times. Its amount during cells incubation in the light did not change. The decline of glycogen level in cells during their incubation in darkness was accompanied by piling up of carbonic acids in the environment acetate prevailing among them.

A volcanic environment for bedrock diagenesis at Meridiani Planum on Mars.

PubMed

McCollom, Thomas M; Hynek, Brian M

2005-12-22

Exposed bedrocks at Meridiani Planum on Mars display chemical and mineralogical evidence suggesting interaction with liquid water. On the basis of morphological observations as well as high abundances of haematite and sulphate minerals, the rocks have been interpreted as sediments that were deposited in a shallow body of briny water with subsequent evaporation leaving behind the sulphate minerals. The iron-sulphur mineralization at Meridiani has also been inferred to be analogous to that produced during oxidative weathering of metal sulphide minerals, such as occurs at acid mine drainage sites. Neither of these interpretations, however, is consistent with the chemical composition of the rocks. Here we propose an alternative model for diagenesis of Meridiani bedrock that involves deposition of volcanic ash followed by reaction with condensed sulphur dioxide- and water-bearing vapours emitted from fumaroles. This scenario does not require prolonged interaction with a standing body of surface water and may have occurred at high temperatures. Consequently, the model invokes an environment considerably less favourable for biological activity on Mars than previously proposed interpretations.

Questa Baseline and Pre-Mining Ground-Water Quality Investigation. 25. Summary of Results and Baseline and Pre-Mining Ground-Water Geochemistry, Red River Valley, Taos County, New Mexico, 2001-2005

USGS Publications Warehouse

Nordstrom, D. Kirk

2008-01-01

Active and inactive mine sites are challenging to remediate because of their complexity and scale. Regulations meant to achieve environmental restoration at mine sites are equally challenging to apply for the same reasons. The goal of environmental restoration should be to restore contaminated mine sites, as closely as possible, to pre-mining conditions. Metalliferous mine sites in the Western United States are commonly located in hydrothermally altered and mineralized terrain in which pre-mining concentrations of metals were already anomalously high. Typically, those pre-mining concentrations were not measured, but sometimes they can be reconstructed using scientific inference. Molycorp?s Questa molybdenum mine in the Red River Valley, northern New Mexico, is located near the margin of the Questa caldera in a highly mineralized region. The State of New Mexico requires that ground-water quality standards be met on closure unless it can be shown that potential contaminant concentrations were higher than the standards before mining. No ground water at the mine site had been chemically analyzed before mining. The aim of this investigation, in cooperation with the New Mexico Environment Department (NMED), is to infer the pre-mining ground-water quality by an examination of the geologic, hydrologic, and geochemical controls on ground-water quality in a nearby, or proximal, analog site in the Straight Creek drainage basin. Twenty-seven reports contain details of investigations on the geological, hydrological, and geochemical characteristics of the Red River Valley that are summarized in this report. These studies include mapping of surface mineralogy by Airborne Visible-Infrared Imaging Spectrometry (AVIRIS); compilations of historical surface- and ground- water quality data; synoptic/tracer studies with mass loading and temporal water-quality trends of the Red River; reaction-transport modeling of the Red River; environmental geology of the Red River Valley; lake-sediment chemistry; geomorphology and its effect on ground-water flow; geophysical studies on depth to ground-water table and depth to bedrock; bedrock fractures and their potential influence on ground-water flow; leaching studies of scars and waste-rock piles; mineralogy and mineral chemistry and their effect on ground-water quality; debris-flow hazards; hydrology and water balance for the Red River Valley; ground-water geochemistry of selected wells undisturbed by mining in the Red River Valley; and quality assurance and quality control of water analyses. Studies aimed specifically at the Straight Creek natural-analog site include electrical surveys; high-resolution seismic survey; age-dating with tritium/helium; water budget; ground-water hydrology and geochemistry; and comparison of mineralogy and lithology to that of the mine site. The highly mineralized and hydrothermally altered volcanic rocks of the Red River Valley contain several percent pyrite in the quartz-sericite-pyrite (QSP) alteration zone, which weather naturally to acid-sulfate surface and ground waters that discharge to the Red River. Weathering of waste-rock piles containing pyrite also contributes acid water that eventually discharges into the Red River. These acid discharges are neutralized by circumneutral-pH, carbonate-buffered surface and ground waters of the Red River. The buffering capacity of the Red River, however, decreases from the town of Red River to the U.S. Geological Survey (USGS) gaging station near Questa. During short, but intense, storm events, the buffering capacity is exceeded and the river becomes acid from the rapid flushing of acidic materials from natural scar areas. The lithology, mineralogy, elevation, and hydrology of the Straight Creek proximal analog site were found to closely approximate those of the mine site with the exception of the mine site?s Sulphur Gulch catchment. Sulphur Gulch contains three subcatchments?upper Sulphur Gulch, Blind Gulch, and Spring Gulc

Effect of Eicosapentaenoic acid (EPA) supplementation on cardiovascular markers in patients with type 2 diabetes mellitus: A randomized, double-blind, placebo-controlled trial.

PubMed

Golzari, Mohammad Hassan; Javanbakht, Mohammad Hassan; Ghaedi, Ehsan; Mohammadi, Hamed; Djalali, Mahmoud

2018-05-01

Cardiovascular complications are one of main cause of increased mortality and morbidity among Diabetes Mellitus (DM) patients. Altered metabolism of sulphur amino acids in diabetes reflected as increases in concentration of methionine and cysteine/cystine in the blood which known as a markers of Cardiovascular Diseases (CVD). The aim of present study was to determine the effect of Eicosapentaenoic acid (EPA) supplementation on sulfhydryl amino acids and Atherogenic Index of Plasma (AIP) in patients with type 2 DM (T2DM). A randomized, double-blind, placebo-controlled clinical trial was performed in 36 control and patients with DM. The subjects were randomly assigned to obtain 2 g/d EPA (n = 18) or placebo (n = 18) for 8 weeks. Fasting serum level of Cystein and Methionine were measured using HPLC method and atherogenic index of plasma (AIP) as a proxy measure of atherosclerosis was computed. Eight weeks supplementation with EPA led to significant reductions in Met (p < 0.002) and Cys (p < 0.001) compared with the placebo (p < 0.06). In addition, compared to placebo a significant reduction in AIP were seen after taking EPA (p < 0.04). EPA supplementation in patients with T2DM for eight weeks had beneficial effects on Met, Cys and AIP, which may attribute to the prevention of vascular complications in the T2DM patients. Copyright © 2018 Diabetes India. Published by Elsevier Ltd. All rights reserved.

High temperature abatement of acid gases from waste incineration. Part I: experimental tests in full scale plants.

PubMed

Biganzoli, Laura; Racanella, Gaia; Rigamonti, Lucia; Marras, Roberto; Grosso, Mario

2015-02-01

In recent years, several waste-to-energy plants in Italy have experienced an increase of the concentration of acid gases (HCl, SO2 and HF) in the raw gas. This is likely an indirect effect of the progressive decrease of the amount of treated municipal waste, which is partially replaced by commercial waste. The latter is characterised by a higher variability of its chemical composition because of the different origins, with possible increase of the load of halogen elements such as chlorine (Cl) and fluorine (F), as well as of sulphur (S). A new dolomitic sorbent was then tested in four waste-to-energy plants during standard operation as a pre-cleaning stage, to be directly injected at high temperature in the combustion chamber. For a sorbent injection of about 6 kg per tonne of waste, the decrease of acid gases concentration downstream the boiler was in the range of 7-37% (mean 23%) for HCl, 34-95% (mean 71%) for SO2 and 39-80% (mean 63%) for HF. This pre-abatement of acid gases allowed to decrease the feeding rate of the traditional low temperature sorbent (sodium bicarbonate in all four plants) by about 30%. Furthermore, it was observed by the plant operators that the sorbent helps to keep the boiler surfaces cleaner, with a possible reduction of the fouling phenomena and a consequent increase of the specific energy production. A preliminary quantitative estimate was carried out in one of the four plants. Copyright © 2014 Elsevier Ltd. All rights reserved.

Influence of endogenous opiates on the hypotensive action of taurine in DOCA-salt rats.

PubMed

Sato, Y; Fujita, T

1988-12-01

We studied the role of endogenous opiate activation in the hypotensive action of taurine, a sulphur amino acid, in deoxycorticosterone acetate (DOCA)-salt hypertensive rats. Previous work had shown that supplementation with 1% taurine reduced blood pressure when given after DOCA-salt hypertension had been established. In the present study, in conscious rats, intraperitoneal injection of naloxone, an opiate antagonist, increased blood pressure in taurine-supplemented DOCA-salt rats, but not in DOCA-salt rats or vehicle-treated control rats. These results suggest that activation of an endogenous opiate might contribute to the hypotensive action of taurine in DOCA-salt hypertensive rats.

The climate penalty for clean fossil fuel combustion

NASA Astrophysics Data System (ADS)

Junkermann, W.; Vogel, B.; Sutton, M. A.

2011-12-01

To cope with the world's growing demand for energy, a large number of coal-fired power plants are currently in operation or under construction. To prevent environmental damage from acidic sulphur and particulate emissions, many such installations are equipped with flue gas cleaning technology that reduces the emitted amounts of sulphur dioxide (SO2) and nitrogen dioxide (NO2). However, the consequences of this technology for aerosol emissions, and in particular the regional scale impact on cloud microphysics, have not been studied until now. We performed airborne investigations to measure aerosol size distributions in the air masses downwind of coal-fired power installations. We show how the current generation of clean technology reduces the emission of sulphur and fine particulate matter, but leads to an unanticipated increase in the direct emission of ultrafine particles (1-10 nm median diameter) which are highly effective precursors of cloud condensation nuclei (CCN). Our analysis shows how these additional ultrafine particles probably modify cloud microphysics, as well as precipitation intensity and distribution on a regional scale downwind of emission sources. Effectively, the number of small water droplets might be increased, thus reducing the water available for large droplets and rain formation. The possible corresponding changes in the precipitation budget with a shift from more frequent steady rain to occasionally more vigorous rain events, or even a significant regional reduction of annual precipitation, introduce an unanticipated risk for regional climate and agricultural production, especially in semi-arid climate zones.

The climate penalty for clean fossil fuel combustion

NASA Astrophysics Data System (ADS)

Junkermann, W.; Vogel, B.; Sutton, M. A.

2011-09-01

To cope with the world's growing demand for energy, a large number of coal-fired power plants are currently in operation or under construction. To prevent environmental damage from acidic sulphur and particulate emissions, many such installations are equipped with flue gas cleaning technology that reduces the emitted amounts of sulphur dioxide (SO2) and nitrogen dioxide (NO2). However, the consequences of this technology for aerosol emissions, and in particular the regional scale impact on cloud microphysics, have not been studied until now. We performed airborne investigations to measure aerosol size distributions in the air masses downwind of coal-fired power installations. We show how the current generation of clean technology reduces the emission of sulphur and fine particulate matter, but leads to an unanticipated increase in the direct emission of ultrafine particles (1-10 nm median diameter) which are highly effective precursors of cloud condensation nuclei (CCN). Our analysis shows how these additional ultrafine particles modify cloud microphysics, as well as precipitation intensity and distribution on a regional scale downwind of emission sources. Effectively, the number of small water droplets is increased, thus reducing the water available for large droplets and rain formation. The corresponding changes in the precipitation budget with a shift from more frequent steady rain to occasionally more vigorous rain events, or even a significant regional reduction of annual precipitation, introduce an unanticipated risk for regional climate and agricultural production, especially in semi-arid climate zones.

Optical luminosity of the transient luminous phenomena in Hessdalen, Norway

NASA Astrophysics Data System (ADS)

Gitle Hauge, Bjørn; Kjøniksen, Anna-Lena; Petter Strand, Erling

2017-04-01

Transient luminous phenomena has been observed in the low atmosphere over Hessdalen valley for several decades, first report is claimed to be 200 years old. The area is scattered with old copper, zinc, sulphur and iron mines. The river Hesja divides the valley, running south to north. The river descends from 800 m altitude to 600m. In the middle of the valley, an old copper and sulphur mine feeds the river with its acidic sulphur pollution. Eyewitnesses have reported lights emerging from the river, but most reports are of lights suddenly emerging in low altitudes over the valley, 1000m - 2000m altitude. Common colours are white, yellow, orange and blue. Green is absent. The optical spectrum of the white lights has been obtained several times, indicating a continuous spectrum. The luminosity of the Hessdalen lights has been debated, some speculating that the phenomenońs radiant power reaches up to 1MW. A more moderate calculation done by Teodorani in 2004 suggests 19KW. The cause of the huge difference is due to uncertainty in establishing correct distance to the phenomenon. Recent discoveries done by this team, indicates that the radiant power is usually much lower. For the first time in Hessdalen, pictures with optical spectrums was obtained at a distance not more than 500m. Two similar observations were done from the same position, indicating a possible birthplace. Atmospheric data and spectrum analysis was also coinciding. Data from this short distance observation will be presented.

Rapid analysis of cyclamate in foods and beverages by gas chromatography-electron capture detector (GC-ECD).

PubMed

Yu, Shengbing; Zhu, Binghui; Lv, Fen; Li, Shaoxiao; Huang, Weixiong

2012-10-15

A rapid method for determination of sodium cyclamate in foods and beverages was developed. Sodium cyclamate was converted to N,N-dichloridecyclohexylamine by reaction with sodium hypochlorite under acid condition. N,N-dichloridecyclohexylamine was subsequently extracted by n-hexane and determined by gas chromatography. Conditions such as derivatization time, the concentration of sodium hypochlorite and sulphuric acid were optimised. Amino acids, aliphatic amines, and food additives such as preservatives, dyes and sweeteners showed no interference for quantification of cyclamate. The correlation coefficient of calibration curve was 0.9993 in the range of 5.0-250mg/L. The limits of detection (LOD) and limits of quantification (LOQ) were calculated as three or ten times the signal-to-noise ratio (S/N), respectively. The LOD and LOQ for yellow wine and fruit juice were 0.05 and 0.2mg/L, respectively. The LOD and LOQ for cake and preserved fruit were 0.25 and 0.8mg/kg, respectively. The intra-day and inter-day RSD were 0.28% and 1.1% (n=5), respectively. The method was successfully applied for determination of cyclamate in yellow wine, cake, fruit juice and preserved fruit. This method was simple, fast, and sensitive. It was suitable for the determination of cyclamate in foods and beverages for safety and quality control inspections. Copyright © 2012 Elsevier Ltd. All rights reserved.

Graphite nanoplatelets/multiwalled carbon nanotubes hybrid nanostructure for electrochemical capacitor.

PubMed

Mishra, Ashish Kumar; Ramaprabhu, S

2012-08-01

Recently, the focus on carbon based nanostructures for various applications has been due to their novel properties such as high electrical conductivity, high mechanical strength and high surface area. In the present work, we have investigated the charge storage capacity of modified graphite nanoplatelets and hybrid structure of graphite nanoplatelets-multiwalled carbon nanotubes (MWNTs). These MWNTs can be used as spacers to reduce the possibility of restacking of graphite nanoplatelets and hence increases the surface area of the hybrid carbon nanostructure thereby high degree of metal oxide decoration is achieved over the hybrid structure. MWNTs were prepared by catalytic chemical vapor deposition technique and further purified with air oxidation and acid treatment. Graphite was treated with conc. nitric acid and sulphuric acid in the volumetric ratio of 1:3 for 3 days and these modified graphite nanoplatelets were further stirred with MWNTs in equal weight ratio to form hybrid nanostructure. Further, ruthenium oxide (RuO2) nanoparticles were decorated on this hybrid structure using chemical route followed by calcination. RuO2 decorated hybrid carbon nanostructure was characterized by using X-ray diffraction, Electron microscopy and Raman spectroscopy. The performance of the hybrid structure based nanocomposite as electrochemical capacitor electrodes was analyzed by studing its capacitive and charge-discharge behaviours using cyclic voltammetry and chronopotentiometry techniques and the results have been discussed.

Cation profiling of passive films on stainless steel formed in sulphuric and acetic acid by deconvolution of angle-resolved X-ray photoelectron spectra

NASA Astrophysics Data System (ADS)

Högström, Jonas; Fredriksson, Wendy; Edstrom, Kristina; Björefors, Fredrik; Nyholm, Leif; Olsson, Claes-Olof A.

2013-11-01

An approach for determining depth gradients of metal-ion concentrations in passive films on stainless steel using angle-resolved X-ray photoelectron spectroscopy (ARXPS) is described. The iterative method, which is based on analyses of the oxidised metal peaks, provides increased precision and hence allows faster ARXPS measurements to be carried out. The method was used to determine the concentration depth profiles for molybdenum, iron and chromium in passive films on 316L/EN 1.4432 stainless steel samples oxidised in 0.5 M H2SO4 and acetic acid diluted with 0.02 M Na2B4O7 · 10H2O and 1 M H2O, respectively. The molybdenum concentration in the film is pin-pointed to the oxide/metal interface and the films also contained an iron-ion-enriched surface layer and a chromium-ion-dominated middle layer. Although films of similar composition and thickness (i.e., about 2 nm) were formed in the two electrolytes, the corrosion currents were found to be three orders of magnitude larger in the acetic acid solution. The differences in the layer composition, found for the two electrolytes as well as different oxidation conditions, can be explained based on the oxidation potentials of the metals and the dissolution rates of the different metal ions.

Behaviour of hygrine and cuscohygrine in illicit cocaine production establishes their use as markers for chewing coca leaves in contrast with cocaine abuse.

PubMed

Rubio, Nelida Cristina; Thurmann, Denise; Krumbiegel, Franziska; Pragst, Fritz

2017-02-01

Hygrine (HYG) and cuscohygrine (CUS) are natural alkaloids of coca leaves but are not found in illicit cocaine seizures. Therefore, they were proposed as markers for coca chewing in contrast to cocaine abuse in urine and hair testing. In order to examine at which step of the illegal cocaine production these compounds are lost, coca leaves were processed according to an authentic procedure by extraction with lime and kerosene, re-extraction with sulphuric acid, and precipitation of coca paste with ammonia. Non-extracted and extracted coca leaves, acidic extract and coca paste were analyzed by gas chromatography-mass spectrometry (GC-MS) and liquid chromatography-tandem mass spectrometry (LC-MS/MS) for cocaine, ecgonine methyl ester (EME), cinnamoylcocaine (CIN), HYG, and CUS. It follows from the results that under these conditions, HYG and CUS are extracted only to a minor extent by kerosene and are not precipitated from the acidic re-extract in the coca paste. Due to this behaviour in illegal cocaine production, they fulfil the conditions as markers for coca chewing in an optimal way. However, for unambiguous discrimination between coca chewing and cocaine abuse in human samples, additional markers of manufactured cocaine are required. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Investigation of the possibility of copper recovery from the flotation tailings by acid leaching.

PubMed

Antonijević, M M; Dimitrijević, M D; Stevanović, Z O; Serbula, S M; Bogdanovic, G D

2008-10-01

The flotation tailings pond of the Bor Copper Mine poses a great ecological problem not only for the town of Bor but also for the surrounding soils and watercourses. Since the old flotation tailings contain about 0.2% of copper on the average, we investigated their leaching with sulphuric acid in the absence and presence of an oxidant. The aim was to determine the leaching kinetics of copper and iron as affected by various factors such as: the pH value of the leach solution, stirring speed, pulp density, particle size, concentration of ferric ions, temperature and time for leaching. The average copper and iron recovery obtained was from 60% to 70% and from 2% to 3%, respectively. These results indicate that the old flotation tailings pond represents an important source of secondary raw material for the extraction of copper and that it should be valorized rather than land reclamation. At the end of the paper, a mechanism of dissolution of copper and iron minerals from the tailings was described.

Impulsive excitation of mechanoluminescence in gamma-irradiated CaSO4:Eu phosphors

NASA Astrophysics Data System (ADS)

Kher, R. S.; Dhoble, S. J.; Pandey, R. K.; Upadhyay, A. K.; Khokhar, M. S. K.

2011-01-01

The mechanoluminescence (ML) and thermoluminescence (TL) of γ-irradiated CaSO4:Eu phosphor have been studied. CaSO4 samples having different concentrations of Eu were prepared by dissolving CaSO4.2H2O in sulphuric acid and evaporating the excess acid around 300 °C. ML was excited impulsively by dropping a load onto the sample. Three distinct peaks have been observed in the ML intensity versus time curve. The ML intensity increases with the increasing concentration of the dopant. The effect of temperature on the shape and peak of ML intensity was also recorded. Growth, saturation and broadening in an ML peak were observed. TL glow curves of CaSO4:Eu phosphors at different concentrations contain two TL peaks: the first peak was observed at around 110 °C and the other at 210 °C. Experimental results suggest that the ML excitation is related to the movement of dislocation with defect centres, the increase in ML with temperature is due to the enhancement in dislocation capture probability, and the reduction is due to the thermal bleaching of defect centres.

Metabolism of a new positive inotropic agent, 3,4-dihydro-6-[4-(3,4-dimethoxybenzoyl)-1-piperazinyl]-2(1H)- quinolinone (OPC-8212) in the rat, mouse, dog, monkey and human.

PubMed

Miyamoto, G; Sasabe, H; Tominaga, N; Uegaki, N; Tominaga, M; Shimizu, T

1988-10-01

1. After OPC-8212 was orally given to rats, mice, dogs, monkeys and humans, its metabolites were identified by n.m.r. and mass spectrometry, and their concentrations in the plasma, urine and faeces of these species were measured by high-performance liquid chromatography (h.p.l.c.). 2. Hydrolysis of the amide group, oxidation and cleavage of the piperazine ring, O-demethylation of the methoxy group, and conjugation were proposed as metabolic pathways of OPC-8212. 3. In rats, mice and monkeys given OPC-8212 orally, metabolites M-1 to M-6 were detected in the plasma, urine and faeces, while M-1, -4, -5 and M-6 were detected in dogs, and M-1, M-3, M-4, M-5 and M-6 were detected in humans. 4. Conjugates of metabolites M-6 and M-7, with glucuronic acid and sulphuric acid, were observed in the urine of rats and humans.

A novel fullerene lipoic acid derivative: Synthesis and preparation of self-assembled monolayers on gold

NASA Astrophysics Data System (ADS)

Viana, A. S.; Leupold, S.; Eberle, C.; Shokati, T.; Montforts, F.-P.; Abrantes, L. M.

2007-11-01

Synthesis and preparation of self-assembled monolayers of a novel fullerene lipoic acid derivative on gold are reported. The presence of densely packed SAMs was confirmed by ellipsometry and cyclic voltammetry. The electrochemical response of the modified electrode in organic media exhibits the first two redox peaks characteristic of the extended π-electron system of fullerene. C 60 surface coverage (1.4 × 10 -10 mol cm -2) has been electrochemically determined by the redox process of the adsorbed fullerene moiety and by reductive desorption of the SAM in strong alkaline solution. Electrochemical data indicate that all four sulphur atoms are involved in the self-assembly process, providing an increase of SAM stability in comparison to mono or di-thiolated appended molecules. Visualisation of discrete fullerene molecules by scanning tunnelling microscopy supplied further evidence for gold modification and molecular distribution on the surface. Mixed monolayers of hexanethiol and fullerene derivatives in a proportion of 1:2 have been also studied with the purpose of controlling the amount and distribution of fullerene units on the gold surface.

Organic Carbon Mobilisation Mechanisms: Evidence from Globally Distributed Stalagmite Records

NASA Astrophysics Data System (ADS)

Baldini, J. U. L.; Fairchild, I. J.; Wynn, P.; Bourdin, C.; Muller, W.; Hartland, A.; Perrette, Y.; Worrall, F.; Bartlett, R.

2017-12-01

Identifying the cause of widespread increases in surface water dissolved organic carbon (DOC) concentrations in recent years is the subject of a contentious debate. Although DOC trends may partially reflect climate change, in many catchments they may also result from increased soil carbon solubility associated with decreases in acid rain due to lower atmospheric sulphur emissions. However, the lack of long-term DOC records hampers constraining climate's role in modulating DOC trends versus that of recovery from acidification. Here we help clarify the causes of recent DOC increases by using a combination of laboratory soil experiments and new stalagmite geochemical data. Laboratory experiments with soils sampled from above several key caves simulate the effect of acidity, temperature, and soil microbial processes on DOC release. These experiments are used to inform records of DOC encoded within several stalagmites from currently acidified, previously acidified, and unacidified sites, and which collectively yield insights into the timing of DOC change in the past. These records of stalagmite DOC concentration and composition are discussed within the context of the ongoing debate regarding the mechanism responsible for DOC release.

Animal products, diseases and drugs: a plea for better integration between agricultural sciences, human nutrition and human pharmacology.

PubMed

Christophersen, Olav A; Haug, Anna

2011-01-20

Eicosanoids are major players in the pathogenesis of several common diseases, with either overproduction or imbalance (e.g. between thromboxanes and prostacyclins) often leading to worsening of disease symptoms. Both the total rate of eicosanoid production and the balance between eicosanoids with opposite effects are strongly dependent on dietary factors, such as the daily intakes of various eicosanoid precursor fatty acids, and also on the intakes of several antioxidant nutrients including selenium and sulphur amino acids. Even though the underlying biochemical mechanisms have been thoroughly studied for more than 30 years, neither the agricultural sector nor medical practitioners have shown much interest in making practical use of the abundant high-quality research data now available. In this article, we discuss some specific examples of the interactions between diet and drugs in the pathogenesis and therapy of various common diseases. We also discuss, using common pain conditions and cancer as specific examples, how a better integration between agricultural science, nutrition and pharmacology could lead to improved treatment for important diseases (with improved overall therapeutic effect at the same time as negative side effects and therapy costs can be strongly reduced). It is shown how an unnaturally high omega-6/omega-3 fatty acid concentration ratio in meat, offal and eggs (because the omega-6/omega-3 ratio of the animal diet is unnaturally high) directly leads to exacerbation of pain conditions, cardiovascular disease and probably most cancers. It should be technologically easy and fairly inexpensive to produce poultry and pork meat with much more long-chain omega-3 fatty acids and less arachidonic acid than now, at the same time as they could also have a similar selenium concentration as is common in marine fish. The health economic benefits of such products for society as a whole must be expected vastly to outweigh the direct costs for the farming sector.

A linked spatial and temporal model of the chemical and biological status of a large, acid-sensitive river network.

PubMed

Evans, Chris D; Cooper, David M; Juggins, Steve; Jenkins, Alan; Norris, Dave

2006-07-15

Freshwater sensitivity to acidification varies according to geology, soils and land-use, and consequently it remains difficult to quantify the current extent of acidification, or its biological impacts, based on limited spot samples. The problem is particularly acute for river systems, where the transition from acid to circum-neutral conditions can occur within short distances. This paper links an established point-based long-term acidification model (MAGIC) with a landscape-based mixing model (PEARLS) to simulate spatial and temporal variations in acidification for a 256 km(2) catchment in North Wales. Empirical relationships are used to predict changes in the probability of occurrence of an indicator invertebrate species, Baetis rhodani, across the catchment as a function of changing chemical status. Results suggest that, at present, 27% of the river network has a mean acid neutralising capacity (ANC) below a biologically-relevant threshold of 20 microeq l(-1). At high flows, this proportion increases to 45%. The model suggests that only around 16% of the stream network had a mean ANC < 20 microeq l(-1) in 1850, but that this increased to 42% at the sulphur deposition peak around 1970. By 2050 recovery is predicted, but with some persistence of acid conditions in the most sensitive, peaty headwaters. Stream chemical suitability for Baetis rhodani is also expected to increase in formerly acidified areas, but for overall abundance to remain below that simulated in 1850. The approach of linking plot-scale process-based models to catchment mixing models provides a potential means of predicting the past and future spatial extent of acidification within large, heterogeneous river networks and regions. Further development of ecological response models to include other chemical predictor variables and the effects of acid episodes would allow more realistic simulation of the temporal and spatial dynamics of ecosystem recovery from acidification.

Animal products, diseases and drugs: a plea for better integration between agricultural sciences, human nutrition and human pharmacology

PubMed Central

2011-01-01

Eicosanoids are major players in the pathogenesis of several common diseases, with either overproduction or imbalance (e.g. between thromboxanes and prostacyclins) often leading to worsening of disease symptoms. Both the total rate of eicosanoid production and the balance between eicosanoids with opposite effects are strongly dependent on dietary factors, such as the daily intakes of various eicosanoid precursor fatty acids, and also on the intakes of several antioxidant nutrients including selenium and sulphur amino acids. Even though the underlying biochemical mechanisms have been thoroughly studied for more than 30 years, neither the agricultural sector nor medical practitioners have shown much interest in making practical use of the abundant high-quality research data now available. In this article, we discuss some specific examples of the interactions between diet and drugs in the pathogenesis and therapy of various common diseases. We also discuss, using common pain conditions and cancer as specific examples, how a better integration between agricultural science, nutrition and pharmacology could lead to improved treatment for important diseases (with improved overall therapeutic effect at the same time as negative side effects and therapy costs can be strongly reduced). It is shown how an unnaturally high omega-6/omega-3 fatty acid concentration ratio in meat, offal and eggs (because the omega-6/omega-3 ratio of the animal diet is unnaturally high) directly leads to exacerbation of pain conditions, cardiovascular disease and probably most cancers. It should be technologically easy and fairly inexpensive to produce poultry and pork meat with much more long-chain omega-3 fatty acids and less arachidonic acid than now, at the same time as they could also have a similar selenium concentration as is common in marine fish. The health economic benefits of such products for society as a whole must be expected vastly to outweigh the direct costs for the farming sector. PMID:21247506

Mineralogy and geochemistry of efflorescent minerals on mine tailings and their potential impact on water chemistry.

PubMed

Grover, B P C; Johnson, R H; Billing, D G; Weiersbye, I M G; Tutu, H

2016-04-01

In the gold mining Witwatersrand Basin of South Africa, efflorescent mineral crusts are a common occurrence on and nearby tailings dumps during the dry season. The crusts are readily soluble and generate acidic, metal- and sulphate-rich solutions on dissolution. In this study, the metal content of efflorescent crusts at an abandoned gold mine tailings dump was used to characterise surface and groundwater discharges from the site. Geochemical modelling of the pH of the solution resulting from the dissolution of the crusts was used to better understand the crusts' potential impact on water chemistry. The study involved two approaches: (i) conducting leaching experiments on oxidised and unoxidised tailings using artificial rainwater and dilute sulphuric acid and correlating the composition of crusts to these leachates and (ii) modelling the dissolution of the crusts in order to gain insight into their mineralogy and their potential impact on receiving waters. The findings suggested that there were two chemically distinct discharges from the site, namely an aluminium- and magnesium-rich surface water plume and an iron-rich groundwater plume. The first plume was observed to originate from the oxidised tailings following leaching with rainwater while the second plume originated from the underlying unoxidised tailings with leaching by sulphuric acid. Both groups of minerals forming from the respective plumes were found to significantly lower the pH of the receiving water with simulations of their dissolution found to be within 0.2 pH units of experimental values. It was observed that metals in a low abundance within the crust (for example, iron) had a stronger influence on the pH of the resulting solutions than metals in a greater abundance (aluminium or magnesium). Techniques such as powder X-ray diffraction (PXRD) and in situ mineral determination techniques such as remote sensing can effectively determine the dominant mineralogy. However, the minerals or metals incorporated through solid solution into bulk mineralogy that dominates the chemistry of the solutions upon their dissolution may occur in minor quantities that can only be predicted using chemical analysis. Their mineralogy can be predicted using geochemical modelling and can provide a set of hypothetical minerals that upon dissolution yield a solution similar to that of the actual crusts. This realisation has a bearing on decision-making such as in risk assessment and designing pollutant mitigation strategies.

The fruit of the date palm: its possible use as the best food for the future?

PubMed

Al-Shahib, Walid; Marshall, Richard J

2003-07-01

The fruits (dates) of the date palm (Phoenix dactylifera L.) contain a high percentage of carbohydrate (total sugars, 44-88%), fat (0.2-0.5%), 15 salts and minerals, protein (2.3-5.6%), vitamins and a high percentage of dietary fibre (6.4-11.5%). The flesh of dates contains 0.2-0.5% oil, whereas the seed contains 7.7-9.7% oil. The weight of the seed is 5.6-14.2% of the date. The fatty acids occur in both flesh and seed as a range of saturated and unsaturated acids, the seeds containing 14 types of fatty acids, but only eight of these fatty acids occur in very low concentration in the flesh. Unsaturated fatty acids include palmitoleic, oleic, linoleic and linolenic acids. The oleic acid content of the seeds varies from 41.1 to 58.8%, which suggests that the seeds of date could be used as a source of oleic acid. There are at least 15 minerals in dates. The percentage of each mineral in dried dates varies from 0.1 to 916 mg/100 g date depending on the type of mineral. In many varieties, potassium can be found at a concentration as high as 0.9% in the flesh while it is as high as 0.5% in some seeds. Other minerals and salts that are found in various proportions include boron, calcium, cobalt, copper, fluorine, iron, magnesium, manganese, potassium, phosphorous, sodium and zinc. Additionally, the seeds contain aluminum, cadmium, chloride, lead and sulphur in various proportions. Dates contain elemental fluorine that is useful in protecting teeth against decay. Selenium, another element believed to help prevent cancer and important in immune function, is also found in dates. The protein in dates contains 23 types of amino acids, some of which are not present in the most popular fruits such as oranges, apples and bananas. Dates contain at least six vitamins including a small amount of vitamin C, and vitamins B(1) thiamine, B(2) riboflavin, nicotinic acid (niacin) and vitamin A. The dietary fibre of 14 varieties of dates has been shown to be as high as 6.4-11.5% depending on variety and degree of ripeness. Dates contain 0.5-3.9% pectin, which may have important health benefits. The world production of dates has increased 2.9 times over 40 years, whereas the world population has doubled. The total world export of dates increased by 1.71% over 40 years. In many ways, dates may be considered as an almost ideal food, providing a wide range of essential nutrients and potential health benefits.

Intensified synthesis of medium chain triglycerides using ultrasonic reactors at a capacity of 4L.

PubMed

Mohod, Ashish V; Gogate, Parag R

2018-04-01

Lipids are considered as one of the most crucial nutrients for humans and among the various classes, medium chain triglycerides (MCTs) are considered as the most important functional foods and nutraceuticals. The present work deals with the intensification of synthesis of MCTs at a large capacity of 4L based on the use of ultrasonic bath and ultrasonic longitudinal horn. The effect of operating parameters like molar ratio of the reactants, type of catalyst and catalyst loading as well as the temperature on the extent of conversion has been investigated. The effect of molar ratio of lauric acid and glycerol was investigated over the range of 1:2 to 1:8 whereas the effect of loading of sulfuric acid was studied over the range of 4 ml/L-10 ml/L and zinc chloride loading over the range of 1 g/L-4 g/L. The effect of temperature was also studied using the conventional approach where it has been observed that 90 °C is an optimum temperature giving the extent of conversion as 72%. Also, the use of homogeneous catalyst as sulphuric acid was found to be more effective as compared to the solid catalyst as zinc chloride. It was observed that the maximum extent of conversion as 77.5% was obtained at 8 ml/L of sulfuric acid and molar ratio of 1:6 using ultrasonic longitudinal horn with US bath giving lower conversion as compared to US longitudinal horn but higher than the conventional approach under same operating conditions. The present work clearly established the intensification benefits in terms of reduction in time and higher conversion using cavitational reactors. Copyright © 2017 Elsevier B.V. All rights reserved.

Enhancement of p-nitrophenol adsorption capacity through N2-thermal-based treatment of activated carbons

NASA Astrophysics Data System (ADS)

Álvarez-Torrellas, S.; Martin-Martinez, M.; Gomes, H. T.; Ovejero, G.; García, J.

2017-08-01

In this work several activated carbons showing different textural and chemical properties were obtained by chemical and physical activation methods, using a lignocellulosic material (peach stones) as precursor. The activated carbon resulting from the chemical activation, namely as CAC, revealed the best textural properties (SBET = 1521 m2 g-1, pore volume = 0.90 cm3 g-1) and an acidic character. It was found that the activated carbon obtained at 300 °C (under air atmosphere, PAC_air), and those synthesized at 750 °C in presence of N2 flow with bubbling of water/12 M H3PO4 solution (PAC_N2(H2O)/PAC_N2(H3PO4)), respectively, revealed worse textural properties, compared to CAC. Two functionalization treatments, by using sulphuric acid at boiling temperature (PACS) and nitric acid-urea-N2 heating at 800 °C (PAC-NUT), were applied to PAC_air, in order to enhance the adsorption ability of the carbon material. Several techniques were carried out to characterize the physical and chemical properties of the obtained carbon materials. The modification treatments had influence on the carbon surface properties, since the nitric acid-urea-N2 heating treatment led to a carbon material with highly-improved properties (SBET = 679 m2 g-1, pHIEP = 5.3). Accordingly, the original and modified-carbon materials were tested as adsorbents to remove 4-nitrophenol (4-NP), assessing batch and fixed-bed column adsorption tests. PAC-NUT carbon offered the best adsorption behavior (qe = 234 mg g-1), showing a high ability for the removal of 4-NP from water.

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuboňová, L., E-mail: lenka.kubonova@vsb.cz; Langová, Š.; Nowak, B.

2013-11-15

Highlights: • MSW fly ash was thermally and hydrometallurgically treated to remove heavy metals. • More than 90% of easy volatile heavy metals (Cd and Pb) were removed thermally. • More than 90% of Cd, Cr, Cu an Zn were removed by alkaline – acid leaching. • The best results were obtained for the solution of 3 M NaOH and 2 M H{sub 2}SO{sub 4}. - Abstract: Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be amore » potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050 °C and in a muffle oven at temperatures from 500 to 1200 °C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel.« less

Role of lipase in the regulation of postprandial gastric acid secretion and emptying of fat in humans: a study with orlistat, a highly specific lipase inhibitor

PubMed Central

Borovicka, J; Schwizer, W; Guttmann, G; Hartmann, D; Kosinski, M; Wastiel, C; Bischof-Delaloye, A; Fried, M

2000-01-01

BACKGROUND AND AIMS—To investigate the importance of lipase on gastric functions, we studied the effects of orlistat, a potent and specific inhibitor of lipase, on postprandial gastric acidity and gastric emptying of fat.
METHODS—Fourteen healthy volunteers participated in a double blind, placebo controlled, randomised study. In a two way cross over study with two test periods of five days, separated by at least 14 days, orlistat 120 mg three times daily or placebo was given with standardised daily meals. In previous experiments we found that this dose almost completely inhibited postprandial duodenal lipase activity. Subjects underwent 28 hour intragastric pH-metry on day 4, and a gastric emptying study with a mixed meal (800 kcal) labelled with 999mTc sulphur colloid (solids) and 111Inthiocyanate (fat) on day 5. Gastric pH data were analysed for three postprandial hours and the interdigestive periods.
RESULTS—Orlistat inhibited almost completely (by 75%) lipase activity and accelerated gastric emptying of both the solid (by 52%) and fat (by 44%) phases of the mixed meal (p<0.03). Orlistat increased postprandial gastric acidity (from a median pH of 3.3 to 2.7; p<0.01). Postprandial cholecystokinin release was lower with orlistat (p<0.03).
CONCLUSION—Lipase has an important role in the regulation of postprandial gastric acid secretion and fat emptying in humans. These effects might be explained by lipolysis induced release of cholecystokinin.


Keywords: lipase; orlistat; gastric secretion; gastric emptying; pH-metry PMID:10807887

Vibrational spectroscopy and electrophoresis as a "golden means" in monitoring of polysaccharides in medical plant and gels

NASA Astrophysics Data System (ADS)

Pielesz, A.

In recent years, some bioactive polysaccharides isolated from natural sources have attracted much attention in the field of biochemistry and pharmacology. Of them, polysaccharides or their glycoconjugates were shown to exhibit multiple biological activities including anticarcinogenic, anticoagulant, immunostimulating, antioxidant, etc. Pharmacotherapy using plant-derived substances can be currently regarded as a very promising future alternative to conventional therapy. The advanced biotechnologies available today enable chemical investigation of well-defined bioactive plant components as sources of novel drugs. The need for safer drugs without side effects has led to the use of natural ingredients with proven safety. Special interest is focused on plant polysaccharides. This article attempts to review the current structural and conformational characterization of some importantly bioactive monosaccharides isolated from following plant cell-wall: Symphytum officinale (comfrey), Thymus pulegioides (thyme), Trigonella foenum-graecum L. (fenugreek), Tussilago farfara L. (coltsfoot), Hyssopus officinalis (hyssop), Althaea officinalis L. (marshmallow) and Equisetum arvense L. (horsetail). The chemical structures of monosaccharides were analysed using FTIR and Raman spectroscopies as well as cellulose acetate membrane electrophoresis (CAE). The dried plant samples were gently hydrolysed with sulphuric acid. The presence of glucuronic acid, galacturonic acid, alginic acid, glucose, mannose and xylose in the hydrolysates of reference substances and non-defatted plant films was proved. The possibility of a taxonomic classification of plant cell walls based on infrared and Raman spectroscopies and the use of spectral fingerprinting for authentication and detection of adulteration of products rich in cell-wall materials are discussed. Individual bands were selected to monitor the sugar content in medical plant cell walls and to confirm the identity of the analysed plants.

Vibrational spectroscopy and electrophoresis as a "golden means" in monitoring of polysaccharides in medical plant and gels.

PubMed

Pielesz, A

2012-07-01

In recent years, some bioactive polysaccharides isolated from natural sources have attracted much attention in the field of biochemistry and pharmacology. Of them, polysaccharides or their glycoconjugates were shown to exhibit multiple biological activities including anticarcinogenic, anticoagulant, immunostimulating, antioxidant, etc. Pharmacotherapy using plant-derived substances can be currently regarded as a very promising future alternative to conventional therapy. The advanced biotechnologies available today enable chemical investigation of well-defined bioactive plant components as sources of novel drugs. The need for safer drugs without side effects has led to the use of natural ingredients with proven safety. Special interest is focused on plant polysaccharides. This article attempts to review the current structural and conformational characterization of some importantly bioactive monosaccharides isolated from following plant cell-wall: Symphytum officinale (comfrey), Thymus pulegioides (thyme), Trigonella foenum-graecum L. (fenugreek), Tussilago farfara L. (coltsfoot), Hyssopus officinalis (hyssop), Althaea officinalis L. (marshmallow) and Equisetum arvense L. (horsetail). The chemical structures of monosaccharides were analysed using FTIR and Raman spectroscopies as well as cellulose acetate membrane electrophoresis (CAE). The dried plant samples were gently hydrolysed with sulphuric acid. The presence of glucuronic acid, galacturonic acid, alginic acid, glucose, mannose and xylose in the hydrolysates of reference substances and non-defatted plant films was proved. The possibility of a taxonomic classification of plant cell walls based on infrared and Raman spectroscopies and the use of spectral fingerprinting for authentication and detection of adulteration of products rich in cell-wall materials are discussed. Individual bands were selected to monitor the sugar content in medical plant cell walls and to confirm the identity of the analysed plants. Copyright © 2012 Elsevier B.V. All rights reserved.

An evaluation of carbon steel corrosion under stagnant seawater conditions.

PubMed

Lee, Jason S; Ray, Richard I; Lemieux, Edward J; Falster, Alexander U; Little, Brenda J

2004-01-01

Corrosion of 1020 carbon steel coupons in natural seawater over a 1-year period was more aggressive under strictly anaerobic stagnant conditions than under aerobic stagnant conditions as measured by weight loss and instantaneous corrosion rate (polarization resistance). Under oxygenated conditions, a two-tiered oxide layer of lepidocrocite/goethite formed. The inner layer was extremely tenacious and resistant to acid cleaning. Under anaerobic conditions, the corrosion product was initially a non-tenacious sulphur-rich corrosion product, mackinawite, with enmeshed bacteria. As more sulphide was produced the mackinawite was transformed to pyrrhotite. In both aerobic and anaerobic exposures, corrosion was more aggressive on horizontally oriented coupons compared to vertically oriented samples.

Synthesis of carbon-based quantum dots from starch extracts: Optical investigations.

PubMed

Al-Douri, Y; Badi, N; Voon, C H

2018-03-01

Carbon-based quantum dots (C-QDs) were synthesized through microwave-assisted carbonization of an aqueous starch suspension mediated by sulphuric and phosphoric acids. The as-prepared C-QDs showed blue, green and yellow luminescence without the addition of any surface-passivating agent. The C-QDs were further analyzed by UV-vis spectroscopy to measure the optical response of the organic compound. The energy gaps revealed narrow sizing of C-QDs in the semiconductor range. The optical refractive index and dielectric constant were investigated. The C-QDs size distribution was characterized. The results suggested an easy route to the large scale production of C-QDs materials. Copyright © 2017 John Wiley & Sons, Ltd.

Ultrasound-assisted extraction for total sulphur measurement in mine tailings.

PubMed

Khan, Adnan Hossain; Shang, Julie Q; Alam, Raquibul

2012-10-15

A sample preparation method for percentage recovery of total sulphur (%S) in reactive mine tailings based on ultrasound-assisted digestion (USAD) and inductively coupled plasma-optical emission spectroscopy (ICP-OES) was developed. The influence of various methodological factors was screened by employing a two-level and three-factor (2(3)) full factorial design and using KZK-1, a sericite schist certified reference material (CRM), to find the optimal combination of studied factors and %S. Factors such as the sonication time, temperature and acid combination were studied, with the best result identified as 20 min of sonication, 80°C temperature and 1 ml of HNO(3):1 ml of HCl, which can achieve 100% recovery for the selected CRM. Subsequently a fraction of the 2(3) full factorial design was applied to mine tailings. The percentage relative standard deviation (%RSD) for the ultrasound method is less than 3.0% for CRM and less than 6% for the mine tailings. The investigated method was verified by X-ray diffraction analysis. The USAD method compared favorably with existing methods such as hot plate assisted digestion method, X-ray fluorescence and LECO™-CNS method. Copyright © 2012 Elsevier B.V. All rights reserved.

Microbial community dynamics in Inferno Crater Lake, a thermally fluctuating geothermal spring

PubMed Central

Ward, Laura; Taylor, Michael W; Power, Jean F; Scott, Bradley J; McDonald, Ian R; Stott, Matthew B

2017-01-01

Understanding how microbial communities respond and adjust to ecosystem perturbation is often difficult to interpret due to multiple and often simultaneous variations in observed conditions. In this research, we investigated the microbial community dynamics of Inferno Crater Lake, an acidic geothermal spring in New Zealand with a unique thermal cycle that varies between 30 and 80 °C over a period of 40–60 days. Using a combination of next-generation sequencing, geochemical analysis and quantitative PCR we found that the microbial community composition was predominantly chemolithotrophic and strongly associated with the thermal cycle. At temperatures >65 °C, the microbial community was dominated almost exclusively by sulphur-oxidising archaea (Sulfolobus-like spp.). By contrast, at mesophilic temperatures the community structure was more mixed, comprising both archaea and bacteria but dominated primarily by chemolithotrophic sulphur and hydrogen oxidisers. Multivariate analysis of physicochemical data confirmed that temperature was the only significant variable associated with community turnover. This research contributes to our understanding of microbial community dynamics in variable environments, using a naturally alternating system as a model and extends our limited knowledge of acidophile ecology in geothermal habitats. PMID:28072418

Microbial community dynamics in Inferno Crater Lake, a thermally fluctuating geothermal spring.

PubMed

Ward, Laura; Taylor, Michael W; Power, Jean F; Scott, Bradley J; McDonald, Ian R; Stott, Matthew B

2017-05-01

Understanding how microbial communities respond and adjust to ecosystem perturbation is often difficult to interpret due to multiple and often simultaneous variations in observed conditions. In this research, we investigated the microbial community dynamics of Inferno Crater Lake, an acidic geothermal spring in New Zealand with a unique thermal cycle that varies between 30 and 80 °C over a period of 40-60 days. Using a combination of next-generation sequencing, geochemical analysis and quantitative PCR we found that the microbial community composition was predominantly chemolithotrophic and strongly associated with the thermal cycle. At temperatures >65 °C, the microbial community was dominated almost exclusively by sulphur-oxidising archaea (Sulfolobus-like spp.). By contrast, at mesophilic temperatures the community structure was more mixed, comprising both archaea and bacteria but dominated primarily by chemolithotrophic sulphur and hydrogen oxidisers. Multivariate analysis of physicochemical data confirmed that temperature was the only significant variable associated with community turnover. This research contributes to our understanding of microbial community dynamics in variable environments, using a naturally alternating system as a model and extends our limited knowledge of acidophile ecology in geothermal habitats.

Studies of a urinary biomarker of dietary inorganic sulphur in subjects on diets containing 1-38 mmol sulphur/day and of the half-life of ingested 34SO4(2-).

PubMed

Curno, R; Magee, E A; Edmond, L M; Cummings, J H

2008-09-01

Sulphites are widely used food additives that may damage health, hence limits are set on their use. They are excreted in urine as sulphate, along with sulphate derived from sulphur amino acids. Dietary intakes of sulphites are hard to determine, so we have tested the utility of urinary nitrogen:sulphate ratio as a biomarker of inorganic sulphur (IS) intake. Additionally we determined the half-life of ingested (34)SO(4)(2-) from its urinary excretion. Twenty healthy adult subjects were recruited by poster advertisement, for a 24-h study where they ate specified foods, which were high in IS, in addition to their normal diet. The half-life of ingested (34)SO(4)(2-) was assessed in five healthy volunteers, given 5.9 mmols of Na(2)(34)SO(4) as a single dose and collecting all urine specimens for 72-96 h. Urine and duplicate diets from three previously conducted studies were analysed for nitrogen and sulphate content, thus expanding the range of IS intakes for evaluation. Duplicate diets were analysed for IS content by ion exchange chromatography, while IS intake was predicted from urinary sulphate (g/day S)-(urinary nitrogen (g/day)/18.89). (32)S:(34)S ratios were determined by liquid chromatography mass spectrometry/mass spectrometry. The range of IS intake was 1.3-37.5 mmol S/day. Actual and predicted IS intakes were mmol/day+/-s.e. 9.2+/-0.65 and 7.0+/-0.45, respectively, and were correlated r=0.60 (n=108). The mean half-life of ingested (34)SO(4)(2-) was 8.2 h. From a 24-h urine collection, IS intake from the habitual diet can be determined for groups of individuals. To predict individual intakes of IS, which may include high sporadic amounts from beer and wine, at least 48 h of urine collection would be required.

The tropospheric processing of acidic gases and hydrogen sulphide in volcanic gas plumes as inferred from field and model investigations

NASA Astrophysics Data System (ADS)

Aiuppa, A.; Franco, A.; von Glasow, R.; Allen, A. G.; D'Alessandro, W.; Mather, T. A.; Pyle, D. M.; Valenza, M.

2007-03-01

Improving the constraints on the atmospheric fate and depletion rates of acidic compounds persistently emitted by non-erupting (quiescent) volcanoes is important for quantitatively predicting the environmental impact of volcanic gas plumes. Here, we present new experimental data coupled with modelling studies to investigate the chemical processing of acidic volcanogenic species during tropospheric dispersion. Diffusive tube samplers were deployed at Mount Etna, a very active open-conduit basaltic volcano in eastern Sicily, and Vulcano Island, a closed-conduit quiescent volcano in the Aeolian Islands (northern Sicily). Sulphur dioxide (SO2), hydrogen sulphide (H2S), hydrogen chloride (HCl) and hydrogen fluoride (HF) concentrations in the volcanic plumes (typically several minutes to a few hours old) were repeatedly determined at distances from the summit vents ranging from 0.1 to ~10 km, and under different environmental conditions. At both volcanoes, acidic gas concentrations were found to decrease exponentially with distance from the summit vents (e.g., SO2 decreases from ~10 000 μg/m3at 0.1 km from Etna's vents down to ~7 μg/m3 at ~10 km distance), reflecting the atmospheric dilution of the plume within the acid gas-free background troposphere. Conversely, SO2/HCl, SO2/HF, and SO2/H2S ratios in the plume showed no systematic changes with plume aging, and fit source compositions within analytical error. Assuming that SO2 losses by reaction are small during short-range atmospheric transport within quiescent (ash-free) volcanic plumes, our observations suggest that, for these short transport distances, atmospheric reactions for H2S and halogens are also negligible. The one-dimensional model MISTRA was used to simulate quantitatively the evolution of halogen and sulphur compounds in the plume of Mt. Etna. Model predictions support the hypothesis of minor HCl chemical processing during plume transport, at least in cloud-free conditions. Larger variations in the modelled SO2/HCl ratios were predicted under cloudy conditions, due to heterogeneous chlorine cycling in the aerosol phase. The modelled evolution of the SO2/H2S ratios is found to be substantially dependent on whether or not the interactions of H2S with halogens are included in the model. In the former case, H2S is assumed to be oxidized in the atmosphere mainly by OH, which results in minor chemical loss for H2S during plume aging and produces a fair match between modelled and measured SO2/H2S ratios. In the latter case, fast oxidation of H2S by Cl leads to H2S chemical lifetimes in the early plume of a few seconds, and thus SO2 to H2S ratios that increase sharply during plume transport. This disagreement between modelled and observed plume compositions suggests that more in-detail kinetic investigations are required for a proper evaluation of H2S chemical processing in volcanic plumes.

The tropospheric processing of acidic gases and hydrogen sulphide in volcanic gas plumes as inferred from field and model investigations

NASA Astrophysics Data System (ADS)

Aiuppa, A.; Franco, A.; von Glasow, R.; Allen, A. G.; D'Alessandro, W.; Mather, T. A.; Pyle, D. M.; Valenza, M.

2006-11-01

Improving the constraints on the atmospheric fate and depletion rates of acidic compounds persistently emitted by non-erupting (quiescent) volcanoes is important for quantitatively predicting the environmental impact of volcanic gas plumes. Here, we present new experimental data coupled with modelling studies to investigate the chemical processing of acidic volcanogenic species during tropospheric dispersion. Diffusive tube samplers were deployed at Mount Etna, a very active open-conduit basaltic volcano in eastern Sicily, and Vulcano Island, a closed-conduit quiescent volcano in the Aeolian Islands (northern Sicily). Sulphur dioxide (SO2), hydrogen sulphide (H2S), hydrogen chloride (HCl) and hydrogen fluoride (HF) concentrations in the volcanic plumes (typically several minutes to a few hours old) were repeatedly determined at distances from the summit vents ranging from 0.1 to ~10 km, and under different environmental conditions. At both volcanoes, acidic gas concentrations were found to decrease exponentially with distance from the summit vents (e.g., SO2 decreases from ~10 000 μg/m3 at 0.1 km from Etna's vents down to ~7 μg/m3 at ~10 km distance), reflecting the atmospheric dilution of the plume within the acid gas-free background troposphere. Conversely, SO2/HCl, SO2/HF, and SO2/H2S ratios in the plume showed no systematic changes with plume aging, and fit source compositions within analytical error. Assuming that SO2 losses by reaction are small during short-range atmospheric transport within quiescent (ash-free) volcanic plumes, our observations suggest that, for these short transport distances, atmospheric reactions for H2S and halogens are also negligible. The one-dimensional model MISTRA was used to simulate quantitatively the evolution of halogen and sulphur compounds in the plume of Mt. Etna. Model predictions support the hypothesis of minor HCl chemical processing during plume transport, at least in cloud-free conditions. Larger variations in the modelled SO2/HCl ratios were predicted under cloudy conditions, due to heterogeneous chlorine cycling in the aerosol phase. The modelled evolution of the SO2/H2S ratios is found to be substantially dependent on whether or not the interactions of H2S with halogens are included in the model. In the former case, H2S is assumed to be oxidized in the atmosphere mainly by OH, which results in minor chemical loss for H2S during plume aging and produces a fair match between modelled and measured SO2/H2S ratios. In the latter case, fast oxidation of H2S by Cl leads to H2S chemical lifetimes in the early plume of a few seconds, and thus SO2 to H2S ratios that increase sharply during plume transport. This disagreement between modelled and observed plume compositions suggests that more in-detail kinetic investigations are required for a proper evaluation of H2S chemical processing in volcanic plumes.

Unimolecular rearrangement of the simplest compound models with a selenium-oxygen, selenium-sulphur and selenium-selenium bond: SeXH and HSeXH (X = O,S,Se)

NASA Astrophysics Data System (ADS)

Viana, Rommel B.

2017-04-01

The aim of this study was to characterise the simplest compound models with a selenium-oxygen, selenium-sulphur and selenium-selenium bond as the SeXH and HSeXH isomers (X = O,S,Se). One of the main aspects of this investigation was to provide a description on the isomerisation pathways involving 2[H,Se,X] and 1[2H,Se,X] potential energy surfaces calculated at the CCSD(T)/CBS//MP2/cc-pVTZ level. The energy difference was 13 kcal mol-1 between hydroxyselenide (SeOH) and oxoselenium (HSeO), while a gap of 3 kcal mol-1 was predicted between thiol-selenide (SeSH) and selenol-sulphide (HSeS). The SeOH→HSeO unimolecular rearrangement showed a barrier energy of 44.6 kcal mol-1, decreasing almost two times in sulphur and selenium analogous reactions. In addition, hydroxyselenide (HSeOH), thioselenenic acid (HSeSH) and diselane (HSeSeH) were the global minimum configurations in the ground state, while the energy differences among the other isomers were close to 30 kcal mol-1. The HSeXH→H2SeX and HSeXH→SeXH2 isomerisations showed barrier energies ranging from 40 to 65 kcal mol-1, while these reverse routes presented heights that were three times smaller. The kinetic rate constant of each 1,2-H shift reaction was performed here as well as an analysis of the selenium-chalcogen bonds using natural bond orbital and bond order index methodologies.

Novel carbon nanostructures as catalyst support for polymer electrolyte membrane fuel cells

NASA Astrophysics Data System (ADS)

Natarajan, Sadesh Kumar

Polymer electrolyte membrane fuel cell (PEMFC) technology has advanced rapidly in recent years, with one of active area focused on improving the long-term performance of carbon supported catalysts, which has been recognized as one of the most important issues to be addressed for the commercialization of PEMFCs. The central part of a PEMFC is the membrane electrode assembly (MEA) which consists of two electrodes (anode and cathode) and a cation exchange membrane. These electrodes are commonly made of carbon black (most often, Vulcan XC-72) supported on carbon paper or carbon cloth backings. It is the primary objective of this thesis to prepare and investigate carbon nanostructures (CNS, licensed to Hydrogen Research Institute -- IRH, Quebec, Canada), the carbon material with more graphite component like carbon nanotubes (CNTs) for use as catalyst support in PEMFCs. High energy ball-milling of activated carbon along with transition metal catalysts under hydrogen atmosphere, followed by heat-treatment leads to nanocrystalline structures of carbon called CNS. However, CNS formed in the quartz tube after heat-treatment is inevitably accompanied by many impurities such as metal particles, amorphous carbon and other carbon nanoparticules. Such impurities are a serious impediment to detailed characterization of the properties of nanostructures. In addition, since the surface of CNS is itself rather inert, it is difficult to control the homogeneity and size distribution of Pt nanoparticules. In this thesis work, we demonstrated a novel mean to purify and functionalize CNS via acid-oxidation under reflux conditions. To investigate and quantify these nanostructures X-ray diffraction, electrical conductivity measurements, specific surface area measurements, thermogravimetric analysis, X-ray photoelectron spectroscopy and transmission electron microscopy studies were used. Cyclic voltammetry studies were performed on different samples to derive estimates for the relationship between the composition of the acid mixture and their influence in producing high density of surface functional groups. Such surface functionalization on CNS enhances the reactivity, improves the specificity and provides an avenue for Pt deposition. It was also shown that a 1:1 mixture of 7.5 M sulphuric acid and 15 M nitric acid have generated higher composition of non-acidic functional groups over other acid compositions discussed in this thesis. In this thesis, we also demonstrated a novel method to deposit and disperse platinum clusters on carbon nanotubes via a chemically specific nucleation mechanism. To investigate and quantify these platinized CNS X-ray diffraction, thermogravimetric analysis, atomic adsorption spectroscopy and high resolution transmission electron microscopy were used. An average Pt cluster size of 4 nm was dispersed homogeneously on CNS that was functionalized with the method described above. The corrosive nature of carbon support material is a crucial issue for the commercialization of PEMFC systems. Therefore, electrochemical oxidations of Pt/CNS compared with Pt/C were studied in this thesis with the aim to understand their durability as catalyst support in PEMFCs. The surface oxidation of the catalyst materials has been compared following potentiostatic treatments up to 200 h under condition simulating the PEMFC cathode environment (80°C, nitrogen purged 0.5 M sulphuric acid, and a constant potential of 1.2 V). The degradation of Pt catalysts and the carbon support was also evaluated by measuring the cell voltage at constant load after different oxidation intervals at 1.2 V. The agglomeration of Pt catalyst particles and the changes in surface functional groups of the carbon material at different intervals of electrochemical oxidation was evaluated using X-ray diffraction and thermogravimetric studies. The subsequent electrochemical characterization at different treatment time intervals by both the above methods suggests that CNS is electrochemically more stable than Vulcan XC-72 with less surface oxide formation and Pt surface area loss without sacrificing catalytic activity. (Abstract shortened by UMI.)

Functional Chemical Groups that May Likely Become a Source for the Synthesis of Novel Central Nervous System (CNS) Acting Drugs.

PubMed

Saganuwan, Saganuwan A

2017-01-01

Central Nervous System (CNS) disorders are on increase perhaps due to genetic, enviromental, social and dietetic factors. Unfortunately, a large number of CNS drugs have adverse effects such as addiction, tolerance, psychological and physical dependence. In view of this, literature search was carried out with a view to identify functional chemical groups that may serve as lead molecules for synthesis of compounds that may have CNS activity. The search revealed that heterocycles that have heteroatoms such as nitrogen (N), sulphur (S) and oxygen (O) form the largest class of organic compounds. They replace carbon in a benzene ring to form pyridine. Compounds with furan, thiophene, pyrrole, pyridine, azole, imidazole, indole, purine, pyrimidine, esters, carboxylic acid, aldehyde, pyrylium, pyrone, pyrodine, barbituric acid, barbiturate, quinoline, quinolone, isoquinolone, coumarin, alkylpyridine, picoline, piperidine, diazine, carboxamide, flavonoid glycoside, oxindole, aminophenol, benzimidazole, benzoxazole, benzothiazole, and chromone chemical groups among others may have CNS effects ranging from depression passing through euphoria to convulsion. Examples of the compounds with the functional groups include but not limited to coal tar, pyridostigmine, pralidoxime, quinine, mefloquine, pyrilamine, pyronaridine, ciprofloxacin and piroxicam. A number of them can undergo keto-enol tautomerism. Chiral amines may be used for derivation of chiral carboxylic acids which are components of tautomers. Some tautomers may cause parkinsonism and Stevens Johnson syndrome. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Unusual way of suicide by carbon monoxide. Case Report.

PubMed

Zelený, Michal; Pivnička, Jan; Šindler, Martin; Kukleta, Pavel

2015-01-01

Authors discuss the case of a suicide of a 29-year-old man caused by carbon monoxide (CO) intoxication. What the authors found interesting was the unusual way of committing suicide that required good technical skills and expert knowledge. The level of carboxyhemoglobin (COHb) in the blood of the deceased man was routinely determined by the modified method by Blackmoore (1970), using gas chromatography/thermal conductivity detection. The level of saturation of the hemoglobin by CO in the collected blood sample is determined relatively to the same sample saturated to 100%. In the blood sample of the deceased man the lethal concentration of COHb of 76.5% was determined. Within the following examinations the blood alcohol concentration of 0.05 g.kg(-1) was determined. Further analysis revealed traces of sertraline, its metabolite N-desmethylsertraline, omeprazole and caffeine in the liver tissue, traces of N-desmethylsertraline, ibuprofen and caffeine in urine sample, and only traces of caffeine in the stomach content and blood samples were proved. To commit suicide the man used a sophisticated double container-system equipped with a timer for controlled generation of CO based on the chemical reaction of concentrated sulphuric acid and formic acid. The used timer was set by an electromechanical timer switch that triggered the fatal reaction of the acids while the man was sleeping. The authors discuss an unusual case of suicide by CO intoxication rarely seen in the area of forensic medicine and toxicology that is specific due to its sophisticated way of execution.

Oil industry waste: a potential feedstock for biodiesel production.

PubMed

Abbas, Javeria; Hussain, Sabir; Iqbal, Muhammad Javid; Nadeem, Habibullah; Qasim, Muhammad; Hina, Saadia; Hafeez, Farhan

2016-08-01

The worldwide rising energy demands and the concerns about the sustainability of fossil fuels have led to the search for some low-cost renewable fuels. In this scenario, the production of biodiesel from various vegetable and animal sources has attracted worldwide attention. The present study was conducted to evaluate the production of biodiesel from the oil industry waste following base-catalysed transesterification. The transesterification reaction gave a yield of 83.7% by 6:1 methanol/oil molar ratio, at 60°C over 80 min of reaction time in the presence of NaOH. The gas chromatographic analysis of the product showed the presence of 16 fatty acid methyl esters with linoleic and oleic acid as principal components representing about 31% and 20.7% of the total methyl esters, respectively. The fourier transform infrared spectroscopy spectrum of oil industry waste and transesterified product further confirmed the formation of methyl esters. Furthermore, the fuel properties of oil industry waste methyl esters, such as kinematic viscosity, cetane number, cloud point, pour point, flash point, acid value, sulphur content, cold filter plugging point, copper strip corrosion, density, oxidative stability, higher heating values, ash content, water content, methanol content and total glycerol content, were determined and discussed in the light of ASTM D6751 and EN 14214 biodiesel standards. Overall, this study presents the production of biodiesel from the oil industry waste as an approach of recycling this waste into value-added products.

Impact of antinutritional factors in food proteins on the digestibility of protein and the bioavailability of amino acids and on protein quality.

PubMed

Sarwar Gilani, G; Wu Xiao, Chao; Cockell, Kevin A

2012-08-01

Dietary antinutritional factors have been reported to adversely affect the digestibility of protein, bioavailability of amino acids and protein quality of foods. Published data on these negative effects of major dietary antinutritional factors are summarized in this manuscript. Digestibility and the quality of mixed diets in developing countries are considerably lower than of those in developed regions. For example, the digestibility of protein in traditional diets from developing countries such as India, Guatemala and Brazil is considerably lower compared to that of protein in typical North American diets (54-78 versus 88-94 %). Poor digestibility of protein in the diets of developing countries, which are based on less refined cereals and grain legumes as major sources of protein, is due to the presence of less digestible protein fractions, high levels of insoluble fibre, and/or high concentrations of antinutritional factors present endogenously or formed during processing. Examples of naturally occurring antinutritional factors include glucosinolates in mustard and canola protein products, trypsin inhibitors and haemagglutinins in legumes, tannins in legumes and cereals, gossypol in cottonseed protein products, and uricogenic nucleobases in yeast protein products. Heat/alkaline treatments of protein products may yield Maillard reaction compounds, oxidized forms of sulphur amino acids, D-amino acids and lysinoalanine (LAL, an unnatural nephrotoxic amino acid derivative). Among common food and feed protein products, soyabeans are the most concentrated source of trypsin inhibitors. The presence of high levels of dietary trypsin inhibitors from soyabeans, kidney beans or other grain legumes have been reported to cause substantial reductions in protein and amino acid digestibility (up to 50 %) and protein quality (up to 100 %) in rats and/or pigs. Similarly, the presence of high levels of tannins in sorghum and other cereals, fababean and other grain legumes can cause significant reductions (up to 23 %) in protein and amino acid digestibility in rats, poultry, and pigs. Normally encountered levels of phytates in cereals and legumes can reduce protein and amino acid digestibility by up to 10 %. D-amino acids and LAL formed during alkaline/heat treatment of lactalbumin, casein, soya protein or wheat protein are poorly digestible (less than 40 %), and their presence can reduce protein digestibility by up to 28 % in rats and pigs, and can cause a drastic reduction (100 %) in protein quality, as measured by rat growth methods. The adverse effects of antinutritional factors on protein digestibility and protein quality have been reported to be more pronounced in elderly rats (20-months old) compared to young (5-weeks old) rats, suggesting the use of old rats as a model for assessing the protein digestibility of products intended for the elderly.

Decline in atmospheric sulphur deposition and changes in climate are the major drivers of long-term change in grassland plant communities in Scotland.

PubMed

Mitchell, Ruth J; Hewison, Richard L; Fielding, Debbie A; Fisher, Julia M; Gilbert, Diana J; Hurskainen, Sonja; Pakeman, Robin J; Potts, Jacqueline M; Riach, David

2018-04-01

The predicted long lag time between a decrease in atmospheric deposition and a measured response in vegetation has generally excluded the investigation of vegetation recovery from the impacts of atmospheric deposition. However, policy-makers require such evidence to assess whether policy decisions to reduce emissions will have a positive impact on habitats. Here we have shown that 40 years after the peak of SO x emissions, decreases in SO x are related to significant changes in species richness and cover in Scottish Calcareous, Mestrophic, Nardus and Wet grasslands. Using a survey of vegetation plots across Scotland, first carried out between 1958 and 1987 and resurveyed between 2012 and 2014, we test whether temporal changes in species richness and cover of bryophytes, Cyperaceae, forbs, Poaceae, and Juncaceae can be explained by changes in sulphur and nitrogen deposition, climate and/or grazing intensity, and whether these patterns differ between six grassland habitats: Acid, Calcareous, Lolium, Nardus, Mesotrophic and Wet grasslands. The results indicate that Calcareous, Mesotrophic, Nardus and Wet grasslands in Scotland are starting to recover from the UK peak of SO x deposition in the 1970's. A decline in the cover of grasses, an increase in cover of bryophytes and forbs and the development of a more diverse sward (a reversal of the impacts of increased SO x ) was related to decreased SO x deposition. However there was no evidence of a recovery from SO x deposition in the Acid or Lolium grasslands. Despite a decline in NO x deposition between the two surveys we found no evidence of a reversal of the impacts of increased N deposition. The climate also changed significantly between the two surveys, becoming warmer and wetter. This change in climate was related to significant changes in both the cover and species richness of bryophytes, Cyperaceae, forbs, Poaceae and Juncaceae but the changes differed between habitats. Copyright © 2018 Elsevier Ltd. All rights reserved.

Enargite oxidation: A review

NASA Astrophysics Data System (ADS)

Lattanzi, Pierfranco; Da Pelo, Stefania; Musu, Elodia; Atzei, Davide; Elsener, Bernhard; Fantauzzi, Marzia; Rossi, Antonella

2008-01-01

Enargite, Cu 3AsS 4, is common in some deposit types, e.g. porphyry systems and high sulphidation epithermal deposits. It is of environmental concern as a potential source of arsenic. In this communication, we review the current knowledge of enargite oxidation, based on the existing literature and our own original data. Explicit descriptions of enargite oxidation in natural environments are scarce. The most common oxidized alteration mineral of enargite is probably scorodite, FeAsO 4.2H 2O, with iron provided most likely by pyrite, a phase almost ubiquitously associated with enargite. Other secondary minerals after enargite include arsenates such as chenevixite, Cu 2Fe 2(AsO 4) 2(OH) 4.H 2O, and ceruleite, Cu 2Al 7(AsO 4) 4.11.5H 2O, and sulphates such as brochantite, Cu 4(SO 4)(OH) 6, and posnjakite, Cu 4(SO 4)(OH) 6·H 2O. Detailed studies of enargite field alteration at Furtei, Sardinia, suggest that most alteration occurs through dissolution, as testified by the appearance of etch pits at the surface of enargite crystals. However, apparent replacement by scorodite and cuprian melanterite was observed. Bulk oxidation of enargite in air is a very slow process. However, X-ray photoelectron spectroscopy (XPS) reveals subtle surface changes. From synchrotron-based XPS it was suggested that surface As atoms react very fast, presumably by forming bonds with oxygen. Conventional XPS shows the formation, on aged samples, of a nanometer-size alteration layer with an appreciably distinct composition with respect to the bulk. Mechanical activation considerably increases enargite reactivity. In laboratory experiments at acidic to neutral pH, enargite oxidation/dissolution is slow, although it is accelerated by the presence of ferric iron and/or bacteria such as Acidithiobacillus ferrooxidans and Sulfolobus BC. In the presence of sulphuric acid and ferric iron, the reaction involves dissolution of Cu and formation of native sulphur, subsequently partly oxidized to sulphate. At alkaline pH, the reactivity of enargite is apparently slightly greater. XPS spectra of surfaces conditioned at pH 11 have been interpreted as evidence of formation of a number of surface species, including cupric oxide and arsenic oxide. Treatment with hypochlorite solutions at pH 12.5 quickly produces a coating of cupric oxide. Electrochemical oxidation of enargite typically involves low current densities, confirming that the oxidation process is slow. Important surface changes occur only at high applied potentials, e.g. + 0.74 V vs. SHE. It is confirmed that, at acidic pH, the dominant process is Cu dissolution, accompanied (at + 0.56 V vs. SHE, pH = 1) by formation of native sulphur. At alkaline pH, a number of surface products have been suggested, including copper and arsenic oxides, and copper arsenates. XPS studies of the reacted surfaces demonstrate the evolution of Cu from the monovalent to the divalent state, the formation of As-O bonds, and the oxidation of sulphur to polysulphide, sulphite and eventually sulphate. In most natural and quasi-natural (mining) situations, it is expected that enargite reactivity will be slow. Moreover, it is likely that the release of arsenic will be further slowed down by at least temporary trapping in secondary phases. Therefore, an adequate management of exposed surfaces and wastes should minimize the environmental impact of enargite-bearing deposits. In spite of an increasing body of data, there are several gaps in our knowledge of enargite oxidation. The exact nature of most mechanisms and products remains poorly constrained, and there is a lack of quantitative data on the dependence on parameters such as pH and dissolved oxygen.

Electrokinetic remediation of manganese and ammonia nitrogen from electrolytic manganese residue.

PubMed

Shu, Jiancheng; Liu, Renlong; Liu, Zuohua; Du, Jun; Tao, Changyuan

2015-10-01

Electrolytic manganese residue (EMR) is a solid waste found in filters after sulphuric acid leaching of manganese carbonate ore, which mainly contains manganese and ammonia nitrogen and seriously damages the ecological environment. This work demonstrated the use of electrokinetic (EK) remediation to remove ammonia nitrogen and manganese from EMR. The transport behavior of manganese and ammonia nitrogen from EMR during electrokinetics, Mn fractionation before and after EK treatment, the relationship between Mn fractionation and transport behavior, as well as the effects of electrolyte and pretreatment solutions on removal efficiency and energy consumption were investigated. The results indicated that the use of H2SO4 and Na2SO4 as electrolytes and pretreatment of EMR with citric acid and KCl can reduce energy consumption, and the removal efficiencies of manganese and ammonia nitrogen were 27.5 and 94.1 %, respectively. In these systems, electromigration and electroosmosis were the main mechanisms of manganese and ammonia nitrogen transport. Moreover, ammonia nitrogen in EMR reached the regulated level, and the concentration of manganese in EMR could be reduced from 455 to 37 mg/L. In general, the electrokinetic remediation of EMR is a promising technology in the future.

Integrative functional genomics of salt acclimatization in the model legume Lotus japonicus.

PubMed

Sanchez, Diego H; Lippold, Felix; Redestig, Henning; Hannah, Matthew A; Erban, Alexander; Krämer, Ute; Kopka, Joachim; Udvardi, Michael K

2008-03-01

The model legume Lotus japonicus was subjected to non-lethal long-term salinity and profiled at the ionomic, transcriptomic and metabolomic levels. Two experimental designs with various stress doses were tested: a gradual step acclimatization and an initial acclimatization approach. Ionomic profiling by inductively coupled plasma/atomic emission spectrometry (ICP-AES) revealed salt stress-induced reductions in potassium, phosphorus, sulphur, zinc and molybdenum. Microarray profiling using the Lotus Genechip allowed the identification of 912 probesets that were differentially expressed under the acclimatization regimes. Gas chromatography/mass spectrometry-based metabolite profiling identified 147 differentially accumulated soluble metabolites, indicating a change in metabolic phenotype upon salt acclimatization. Metabolic changes were characterized by a general increase in the steady-state levels of many amino acids, sugars and polyols, with a concurrent decrease in most organic acids. Transcript and metabolite changes exhibited a stress dose-dependent response within the range of NaCl concentrations used, although threshold and plateau behaviours were also observed. The combined observations suggest a successive and increasingly global requirement for the reprogramming of gene expression and metabolic pathways to maintain ionic and osmotic homeostasis. A simple qualitative model is proposed to explain the systems behaviour of plants during salt acclimatization.

An experimental study of gaseous exhaust emissions of diesel engine using blend of natural fatty acid methyl ester

NASA Astrophysics Data System (ADS)

Sudrajad, Agung; Ali, Ismail; Samo, Khalid; Faturachman, Danny

2012-09-01

Vegetable oil form in Natural Fatty Acid Methyl Ester (FAME) has their own advantages: first of all they are available everywhere in the world. Secondly, they are renewable as the vegetables which produce oil seeds can be planted year after year. Thirdly, they are friendly with our environment, as they seldom contain sulphur element in them. This makes vegetable fuel studies become current among the various popular investigations. This study is attempt to optimization of using blend FAME on diesel engine by experimental laboratory. The investigation experimental project is comparison between using blend FAME and base diesel fuel. The engine experiment is conducted with YANMAR TF120M single cylinder four stroke diesel engine set-up at variable engine speed with constant load. The data have been taken at each point of engine speed during the stabilized engine-operating regime. Measurement of emissions parameters at difference engine speed conditions have generally indicated lower in emission NOx, but slightly higher on CO2 emission. The result also shown that the blends FAME are good in fuel consumption and potentially good substitute fuels for diesel engine

Regulation of Plant Cellular and Organismal Development by SUMO.

PubMed

Elrouby, Nabil

2017-01-01

This chapter clearly demonstrates the breadth and spectrum of the processes that SUMO regulates during plant development. The gross phenotypes observed in mutants of the SUMO conjugation and deconjugation enzymes reflect these essential roles, and detailed analyses of these mutants under different growth conditions revealed roles in biotic and abiotic stress responses, phosphate starvation, nitrate and sulphur metabolism, freezing and drought tolerance and response to excess copper. SUMO functions also intersect with those regulated by several hormones such as salicylic acid , abscisic acid , gibberellins and auxin, and detailed studies provide mechanistic clues of how sumoylation may regulate these processes. The regulation of COP1 and PhyB functions by sumoylation provides very strong evidence that SUMO is heavily involved in the regulation of light signaling in plants. At the cellular and subcellular levels, SUMO regulates meristem architecture, the switch from the mitotic cycle into the endocycle, meiosis, centromere decondensation and exit from mitosis, transcriptional control, and release from transcriptional silencing. Most of these advances in our understanding of SUMO functions during plant development emerged over the past 6-7 years, and they may only predict a prominent rise of SUMO as a major regulator of eukaryotic cellular and organismal growth and development.

Physical and chemical pretreatment of lignocellulosics in pineapple (Ananus comosus) peels dried for investment

NASA Astrophysics Data System (ADS)

Sukkaew, Adulsman; Boonsong, Panthip; Thongpradistha, Sriubol; Intan, Maimoon

2017-08-01

Pineapple (Ananus comosus) Peels, once known as waste from agricultural, can be a problem when we eliminate in agriculture and industry. The current technology can help preliminarily to solve this problem. The sustainable solution to this problem is lignocellulosics pretreatments for converted saccharide as a carbon source for ethanol production. The objective of this study is the investigation of pineapple peels pretreatment to produce fermentable sugar by drying and digesting 5% sulfuric acid (H2SO4). And study of cost economic passed selection for investment. The result found that the best investment of drying was 100 °C at 11 hours for the sulphuric acid which could be easily crushed into a fine powder. Moreover, digestion of pineapple peels gave the best total sugar 252.2 g/l by 5% H2SO4 incubated for 60 minutes at room temperature. The pineapple peels were digested by 5%H2SO4 concentration by incubating for 60 minutes at room temperature, finding to be the best condition and the lowest investment. Finally, the optimisation of investment and management for lignocellulosic pretreatment will improve efficiency of strategy for economic and energy development.

New Particle Formation (NPF) within the volcanic plume of Piton de la Fournaise at Maïdo observatory (21.1° S 55.4° E), on La Réunion Island.

NASA Astrophysics Data System (ADS)

Foucart, Brice; Sellegri, Karine; Tulet, Pierre

2017-04-01

Volcanic emissions can have a significant effect on the environment, and may impact climate through the injection of gases and aerosols in the upper troposphere where they have a long residence time and an impact on clouds formation [Makkonen et al., 2012]. The Piton de La Fournaise volcano on La Réunion Island erupted four times in 2015 [Peltier et al., 2016] and volcanic particles were ejected in the atmosphere both as primary particles rapidly deposited due to their large size and secondary particles mainly derived from oxidation of sulphur dioxide. In this study, we focus on this secondary process of forming new aerosol particles (NPF). Sulphuric acid (H2SO4), resulting from SO2 oxidation in the presence of light, is known to be the major precursor to nucleation events [kulmala et al., 2004 and Kerminen et al., 2010]. During the April 2007 eruption of Piton de la Fournaise, Tulet and Villeneuve [2010] estimated by OMI and CALIOP space sensors analysis a total SO2 release of 230 kt, among of which 60 kt that have been transformed into H2SO4 supposing NPF processes. However, the nucleation phenomenon has rarely been directly observed in volcanic environments [Kulmala et al., 2004] except for Mauna Loa volcano on Hawaii [Weber et al., 1995] and for Eyjafjallajokull plume caught at the Puy de Dôme station [Boulon et al., 2011]. Within the STRAP project (Synergie Trans-disciplinaire pour Répondre aux Aléas de Panache Volcanique), a multidisciplinary tracking of a volcanic gas and aerosol plume that has been conducted by Tulet et al. [2016] through a strong collaboration between volcanologists and meteorologists. Part of the measurements were performed at Maïdo observatory (21.1° S 55.4° E) which is located at 40 km from the volcano but which has been reached several times by the volcanic plume, each time accompanied by a NPF event. A statistical analysis of the influence of the plume presence on the NPF frequency, intensity and new particles growth rates is performed over a one year observation period. Then, focusing on the NPF events and according to Kuang et al. [2007], we developed a parameterization of the nucleation rate as a function of a proxy of sulphuric acid within the volcanic plume which can be used in meteorological meso-scale models. Keywords: aerosols, nucleation, volcanic plume, parameterization

Chemical and isotopic characteristics of geothermal fluids from Sulphur Springs, Saint Lucia

NASA Astrophysics Data System (ADS)

Joseph, Erouscilla P.; Fournier, Nicolas; Lindsay, Jan M.; Robertson, Richard; Beckles, Denise M.

2013-03-01

Sulphur Springs is a vigorous, geothermal field associated with the active Soufrière Volcanic Centre in southern Saint Lucia, Lesser Antilles island arc. The 'Sulphur Springs Park' is an important tourist attraction (touted as the 'world's only drive-through volcano') with some of the hot pools being developed into recreational pools. Some 200,000 people visit the park each year. Since 2001, the hydrothermal fluids of Sulphur Springs have been sampled as part of an integrated volcanic monitoring programme for the island. Gas and water samples were analysed to characterise the geochemistry of the hydrothermal system, and to assess the equilibrium state and subsurface temperatures of the reservoir. This has also enabled us, for the first time, to establish baseline data for future geochemical monitoring. The gases are of typical arc-type composition, with N2 excess and low He and Ar content. The dry gas composition is dominated by CO2 (ranging from 601-993 mmol/mol), with deeper magmatic sourced H2S-rich vapour undergoing boiling and redox changes in the geothermal reservoir to emerge with a hydrothermal signature in the fumarolic gases. Fluid contributions from magmatic degassing are also evident, mainly from the moderate to high contents of HCl and deeply-sourced H2S gas, respectively. Sulphur Springs hydrothermal waters have acid-sulphate type compositions (SO4 = 78-4008 mg/L; pH = 3-7), and are of primarily meteoric origin which have been affected by evaporation processes based on the enrichment in both δ18O and δD (δ18O = - 1 to 15‰ and δD = - 9 to 14‰ respectively) in relation to the global meteoric water line (GMWL). These waters are steam-heated water typically formed by absorption of H2S-rich gases in the near surface oxygenated groundwaters. Reservoir temperatures calculated from the evaluation of gas equilibria in the CO2-CH4-H2 system reveal higher temperatures (190 to 300 °C) than those derived from quartz geothermometry (95 to 169 °C), which appeared to be affected by dilution with meteoric waters. Generally, no significant variations in fluid geochemistry of the hydrothermal system were observed between 2001 and 2006, and we propose that there were no changes in the state of volcanic activity during this period.

Investigation of Mineral Alteration in Andesite and Dacite from Three Different Volcano Hydrothermal Systems on Dominica, Lesser Antilles

NASA Astrophysics Data System (ADS)

Smith, C. I. V.; Frey, H. M.; Joseph, E. P.; Manon, M. R. F.

2017-12-01

The thermal discharges of Dominica are classified as steam-heated acidic-sulphate waters, produced by the mixing of shallow ground waters heated by sulphur bearing gases coming from magmatic sources. This study investigates the mineral alteration associated with three hydrothermal areas in Dominica that exhibit different temperature, pH, water composition and surface water abundance. Hydrothermal features (fumaroles, pools, springs) from Sulphur Springs ranged in temperature from 41 - 97 °C and pH from 1-3 in a predominantly gaseous environment, whereas the Valley of Desolation (69-98 °C and pH 1- 4) and the Cold Soufriere (18-32 °C and pH 1-4) have significant inputs of surface water. At each location, the host andesite-dacite rock was enveloped by a thin rind (up 2 cm) of precipitates, but the degree of alteration and rind thickness/composition varied with location. Cobbles from Sulphur Springs (SS) are grayish white in color with a thin outer rind (3-13 mm), and seemingly unaltered cores. Valley of Desolation (VoD) samples have a variety of patterns of alteration, with some clasts a uniform white-orange color, whereas others have variable thicknesses of an altered rind (1-20 mm), with relatively unaltered cores. Multiple hydrothermal minerals precipitated in the outer rinds display distinctive colors, suggestive of sulphides (dark gray), sulphates (orange and yellow), and iron oxides(?) (pink and purple). Cold Soufriere (CS) samples appear to be the most altered, often crumbling at touch. Others had rinds (2-10 mm) and pinkish gray cores that suggest more alteration compared to VoD and SS samples. Preliminary mineral identification of rind compositions was determined by XRD. Scans indicate the presence of silica polymorphs cristobalite and tridymite, as well as pyrite and sulphur. Elemental maps created using a SEM to identify any gradation caused by the elemental leaching and/or precipitation show that the boundaries between the weathering rind and the host rock are distinct. Pyroxenes in the rind are significantly altered and contained gypsum and silica veins, and plagioclase is completely replaced by clay minerals. In the groundmass, there is significant sulphur precipitation, as well as a Ti sulphate/sulfide phase. Additional analysis will allow comparison between the different hydrothermal regions.

Laboratory and Theoretical Studies of Tropospheric Iodine Chemistry (Invited)

NASA Astrophysics Data System (ADS)

Plane, J. M.; Saunders, R. W.; Kumar, R.; Gomez Martin, J.; Mahajan, A. S.; Murray, B. J.

2009-12-01

This paper will discuss progress in understanding two important properties of iodine in the marine boundary layer: ozone depletion and new particle formation. A variety of laboratory techniques have been employed to study the kinetics and growth of iodine oxide particles, their uptake of water, sulphuric and organic acids, and the recyling of iodine from them. The photochemistry of a variety of iodine oxides, which are central to catalytic O3 depletion and are involved in homogeneous condensation, will also be described. The use of high-level quantum chemistry calculations to underpin these experiments will then be discussed. Finally, the implications of this work for understanding the impact of iodine in both remote and polluted marine environments will be considered.

Antimicrobial activity of some Ganoderma species from Nigeria.

PubMed

Ofodile, L N; Uma, N U; Kokubun, T; Grayer, R J; Ogundipe, O T; Simmonds, M S J

2005-04-01

The crude n-hexane:diethyl ether, chloroform:acetone and methanol extracts of four species of Ganoderma (Ganoderma colossum (Fr.) C. F. Baker, G. resinaceum Boud., G. lucidum (cf.) (Curtis) P. Karst. and G. boninense (cf.) Pat.), from Nigeria, were tested for antimicrobial activity. The three solvent extracts of all the species of Ganoderma were active against Pseudomonas syringae and Bacillus subtilis, whereas none of the extracts were active against Cladosporium herbarum. Preliminary thin layer chromatography chemical tests on these extracts of Ganoderma showed that they contained compounds that stained blue-violet and blue or green when sprayed with anisaldehyde-sulphuric acid or Dragendorff, respectively. The profile of compounds in the extracts showed some variation among the four species. (c) 2005 John Wiley & Sons, Ltd.

[Microflora of damaged ferroconcrete structures under the conditions of inhibitory protection].

PubMed

Kopteva, Zh P; Zanina, V V; Purish, L M; Piliashenko-Novokhatnyĭ, A I; Kozlova, I A

2004-01-01

Thionic, sulphate-reducing, denitrifying and ammonifying bacteria widely distributed in the sewer system on various structure elements have been isolated from damaged ferroconcrete samples. Effect of protective materials on microbe-induced corrosion of metal famework of concrete samples has been studied. Selective effect of corrosion inhibitors and coatings on the growth of corrosion-active bacteria of sulphur and nitrogen cycle has been revealed. It is shown that acid medium formed by thionic bacteria is more aggressive than ammonium-hydrosulphide one formed by denitrifying and sulphate-reducing bacteria. It has been established that the corrosion inhibitor--pyrquin, organosilicon coating CO-FMI and epoxyorganosilicon coating 4sk are most effective materials as to the action of thionic bacteria--dangerous agents of ferroconcrete aerobic corrosion.

Synthesis and characterization of a novel potato starch derivative with cationic acetylcholine groups.

PubMed

Zhang, Bing; Ni, Boli; Lü, Shaoyu; Cui, Dapeng; Liu, Mingzhu; Gong, Honghong; Han, Fei

2012-04-01

A novel substance, cationic acetylcholine potato starch (CAPS), was developed for the first time. The synthesis process had three steps: first, carboxymethyl potato starch (CMPS) was synthesized under sodium hydroxide alkaline condition and in isopropyl alcohol organic media; second, bromocholine chloride (BCC) was synthesized with sulphuric acid as a catalytic agent; finally, CAPS was synthesized by the reaction of CMPS with BCC in N,N'-dimethylformamide (DMF). The degree of substitution (DS) of CAPS was determined by ammonia gas-sensing electrode and elemental analysis. CAPS was characterized by Fourier transformed infrared (FTIR) and near infrared (FTNIR) spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD) and differential scanning calorimetry (DSC). Copyright © 2012 Elsevier B.V. All rights reserved.

Kinetic determination of propranolol in tablets by oxidation with ceric sulphate.

PubMed

Sultan, S M; Altamrah, S A; Aziz Alrahman, A M; Alzamil, I Z; Karrar, M O

1989-01-01

A simple and accurate kinetic method for the determination of propranolol has been developed. Cerium(IV) sulphate (0.5 M) is used to oxidize propranolol in 2 M sulphuric acid at room temperature to the ketone form that absorbs light at a lambda max of 525 nm. The fixed-concentration method is used by recording the exact time, t(s), taken for the reaction to reach a fixed absorbance of 0.100. The unknown concentration, c(M), of propranolol is calculated from the equation: l/t = 0 0.000217 + 0.03 c. The method has been applied to the determination of propranolol in proprietary tablets and the results were compared with those obtained by the B.P. and other standard methods.

Hydrochemical and stable isotope indicators of pyrite oxidation in carbonate-rich environment; the Hamersley Basin, Western Australia

NASA Astrophysics Data System (ADS)

Dogramaci, Shawan; McLean, Laura; Skrzypek, Grzegorz

2017-02-01

Sulphur (S) is a commonly occurring element in most aquifers, primarily in oxidised (sulphates) and reduced (sulphides) forms. Sulphides often constitute a risk to groundwater quality due to acid rock drainage, especially in catchments that are subject to mining excavations or groundwater injection. However, in semi-arid regions detection of the acid rock drainage risk can be challenging and traditional methods based on observations of increasing SO4 concentrations or SO4/Cl ratios in surface and groundwater, are not necessarily applicable. In addition, decreasing pH, usually accompanying pyrite oxidation, can be masked by the high pH-neutralisation capacity of carbonate and silicate minerals. Analysis of 73 surface and groundwater samples from different water bodies and aquifers located in the Hamersley Basin, Western Australia found that most of the samples are characterised by neutral pH but there was also a large spatial variability in the dissolved sulphate (SO4) concentrations that ranged from 1 mg/L to 15,000 mg/L. Not surprisingly, groundwater in aquifers that contained pyrite had high sulphate concentrations (>1000 mg/L). This was associated with low δ34SSO4 values (+1.2‰ to +4.6‰) and was consistent with the values obtained from aquifer matrix pyritic rock samples (-1.9‰ to +4.4‰). It was also found that the SO4 concentrations and acidity levels were not only dependent on δ34SSO4 values and existence of pyrite but also on the presence of carbonate minerals in the aquifer matrix. The groundwater in aquifers containing both pyrite and carbonate minerals had a neutral pH and was also saturated with respect to gypsum and had high magnesium concentrations of up to 2200 mg/L suggesting de-dolomitisation as the process buffering the acidity generated by pyrite oxidation. Based on the findings from this study, a classification scheme has been developed for identification of the acid rock drainage contribution to groundwater that encompasses a myriad of geochemical processes that occur in aqueous systems. The classification uses five proxies (SO4, SO4/Cl, SI of calcite, δ34SSO4 and δ18OSO4) to improve assessment of the oxidation of sulphide potential contribution to overall sulphate ion concentrations regardless of acidity levels of the aqueous system.

Structural and physiological analyses of the alkanesulphonate-binding protein (SsuA) of the citrus pathogen Xanthomonas citri.

PubMed

Tófoli de Araújo, Fabiano; Bolanos-Garcia, Victor M; Pereira, Cristiane T; Sanches, Mario; Oshiro, Elisa E; Ferreira, Rita C C; Chigardze, Dimitri Y; Barbosa, João Alexandre Gonçalves; de Souza Ferreira, Luís Carlos; Benedetti, Celso E; Blundell, Tom L; Balan, Andrea

2013-01-01

The uptake of sulphur-containing compounds plays a pivotal role in the physiology of bacteria that live in aerobic soils where organosulfur compounds such as sulphonates and sulphate esters represent more than 95% of the available sulphur. Until now, no information has been available on the uptake of sulphonates by bacterial plant pathogens, particularly those of the Xanthomonas genus, which encompasses several pathogenic species. In the present study, we characterised the alkanesulphonate uptake system (Ssu) of Xanthomonas axonopodis pv. citri 306 strain (X. citri), the etiological agent of citrus canker. A single operon-like gene cluster (ssuEDACB) that encodes both the sulphur uptake system and enzymes involved in desulphurisation was detected in the genomes of X. citri and of the closely related species. We characterised X. citri SsuA protein, a periplasmic alkanesulphonate-binding protein that, together with SsuC and SsuB, defines the alkanesulphonate uptake system. The crystal structure of SsuA bound to MOPS, MES and HEPES, which is herein described for the first time, provides evidence for the importance of a conserved dipole in sulphate group coordination, identifies specific amino acids interacting with the sulphate group and shows the presence of a rather large binding pocket that explains the rather wide range of molecules recognised by the protein. Isolation of an isogenic ssuA-knockout derivative of the X. citri 306 strain showed that disruption of alkanesulphonate uptake affects both xanthan gum production and generation of canker lesions in sweet orange leaves. The present study unravels unique structural and functional features of the X. citri SsuA protein and provides the first experimental evidence that an ABC uptake system affects the virulence of this phytopathogen.

Structural and Physiological Analyses of the Alkanesulphonate-Binding Protein (SsuA) of the Citrus Pathogen Xanthomonas citri

PubMed Central

Tófoli de Araújo, Fabiano; Bolanos-Garcia, Victor M.; Pereira, Cristiane T.; Sanches, Mario; Oshiro, Elisa E.; Ferreira, Rita C. C.; Chigardze, Dimitri Y.; Barbosa, João Alexandre Gonçalves; de Souza Ferreira, Luís Carlos; Benedetti, Celso E.; Blundell, Tom L.; Balan, Andrea

2013-01-01

Background The uptake of sulphur-containing compounds plays a pivotal role in the physiology of bacteria that live in aerobic soils where organosulfur compounds such as sulphonates and sulphate esters represent more than 95% of the available sulphur. Until now, no information has been available on the uptake of sulphonates by bacterial plant pathogens, particularly those of the Xanthomonas genus, which encompasses several pathogenic species. In the present study, we characterised the alkanesulphonate uptake system (Ssu) of Xanthomonas axonopodis pv. citri 306 strain (X. citri), the etiological agent of citrus canker. Methodology/Principal Findings A single operon-like gene cluster (ssuEDACB) that encodes both the sulphur uptake system and enzymes involved in desulphurisation was detected in the genomes of X. citri and of the closely related species. We characterised X. citri SsuA protein, a periplasmic alkanesulphonate-binding protein that, together with SsuC and SsuB, defines the alkanesulphonate uptake system. The crystal structure of SsuA bound to MOPS, MES and HEPES, which is herein described for the first time, provides evidence for the importance of a conserved dipole in sulphate group coordination, identifies specific amino acids interacting with the sulphate group and shows the presence of a rather large binding pocket that explains the rather wide range of molecules recognised by the protein. Isolation of an isogenic ssuA-knockout derivative of the X. citri 306 strain showed that disruption of alkanesulphonate uptake affects both xanthan gum production and generation of canker lesions in sweet orange leaves. Conclusions/Significance The present study unravels unique structural and functional features of the X. citri SsuA protein and provides the first experimental evidence that an ABC uptake system affects the virulence of this phytopathogen. PMID:24282519

Witwatersrand gold deposits formed by volcanic rain, anoxic rivers and Archaean life

NASA Astrophysics Data System (ADS)

Heinrich, Christoph A.

2015-03-01

The Witwatersrand Basin in South Africa is one of the best-preserved records of fluvial sedimentation on an Archaean continent. The basin hosts the worlds biggest gold resource in thin pebble beds, but the process for gold enrichment is debated. Mechanical accumulation of gold particles from flowing river water is the prevailing hypothesis, yet there is evidence for hydrothermal mobilization of gold by fluids invading the metasedimentary rocks after their burial. Earth's atmosphere three billion years ago was oxygen free, but already sustained some of the oldest microbial life on land. Here I use thermodynamic modelling and mass-balance calculations to show that these conditions could have led to the chemical transport and precipitation of gold in anoxic surface waters, reconciling the evidence for fluvial deposition with evidence for hydrothermal-like chemical reactions. I suggest that the release of sulphurous gases from large volcanic eruptions created acid rain that enabled the dissolution and transport of gold in surface waters as sulphur complexes. Precipitation of the richest gold deposits could have been triggered by chemical reduction of the dissolved gold onto organic material in shallow lakes and pools. I conclude that the Witwatersrand gold could have formed only during the Archaean, after the emergence of continental life but before the rise of oxygen in the Earth's atmosphere.

Comparison of volatile sulphur compound production by cheese-ripening yeasts from methionine and methionine-cysteine mixtures.

PubMed

López Del Castillo-Lozano, M; Delile, A; Spinnler, H E; Bonnarme, P; Landaud, S

2007-07-01

Production of volatile sulphur compounds (VSC) was assessed in culture media supplemented with L-methionine or L-methionine/L-cysteine mixtures, using five cheese-ripening yeasts: Debaryomyces hansenii DH47(8), Kluyveromyces lactis KL640, Geotrichum candidum GC77, Yarrowia lipolytica YL200 and Saccharomyces cerevisiae SC45(3). All five yeasts produced VSC with L-methionine or L-methionine/L-cysteine, but different VSC profiles were found. GC77 and YL200 produced dimethyldisulphide and trace levels of dimethyltrisulphide while DH47(8), KL640 and SC45(3) produced mainly methionol and low levels of methional. S-methylthioacetate was produced by all the yeasts but at different concentrations. DH47(8), KL640 and SC45(3) also produced other minor VSC including 3-methylthiopropyl acetate, ethyl-3-methylthiopropanoate, a thiophenone, and an oxathiane. However, VSC production diminished in a strain-dependent behaviour when L-cysteine was supplemented, even at a low concentration (0.2 g l(-1)). This effect was due mainly to a significant decrease in L-methionine consumption in all the yeasts except YL200. Hydrogen sulphide produced by L-cysteine catabolism did not seem to contribute to VSC generation at the acid pH of yeast cultures. The significance of such results in the cheese-ripening context is discussed.

Bioindication of human-induced soil degradation in enclosed karst depressions (dolines) using Ellenberg indicator values (Classical Karst, Slovenia).

PubMed

Breg Valjavec, Mateja; Zorn, Matija; Čarni, Andraž

2018-05-29

One of the frequently used bioindication methods is Ellenberg indicator values (EIVs), which are commonly applied in Central Europe as bioindicators of ecological characteristics. However, very few studies have tested EIVs as a bioindication of human-induced soil degradation. We tested the ability of EIVs to distinguish between localities of degraded karst depressions (dolines) and localities of semi-natural (agricultural) soils in preserved dolines on the Kras Plateau (Classical Karst, SW Slovenia). We compared the results of bioindications of soil nutrient content (N), soil reaction (R) and soil moisture (M) with measured soil parameters. Low values of organic carbon, a slightly alkaline soil reaction and low organic sulphur content are chemical indicators of soil degradation in dolines, in comparison with preserved reference dolines (high organic carbon, slightly acid reaction, higher S). EIV reaction is the most reliable plant indicator value that can distinguish between degraded and non-degraded soil plots. According to a regression tree, sulphur (S) and C/N are the most important factors for division on the basis of EIV reaction. By applying the EIV reaction of diagnostic plant species, we significantly improved bioindication of soil degradation, although in the case of EIV nutrients, bioindication was not improved. Copyright © 2018. Published by Elsevier B.V.

Sequestration of arsenic in ombrotrophic peatlands

NASA Astrophysics Data System (ADS)

Rothwell, James; Hudson-Edwards, Karen; Taylor, Kevin; Polya, David; Evans, Martin; Allott, Tim

2014-05-01

Peatlands can be important stores of arsenic but we are lacking spectroscopic evidence of the sequestration pathways of this toxic metalloid in peatland environments. This study reports on the solid-phase speciation of anthropogenically-derived arsenic in atmospherically contaminated peat from the Peak District National Park (UK). Surface and sub-surface peat samples were analysed by synchrotron X-ray absorption spectroscopy on B18 beamline at Diamond Light Source (UK). The results suggest that there are contrasting arsenic sequestration mechanisms in the peat. The bulk arsenic speciation results, in combination with strong arsenic-iron correlations at the surface, suggest that iron (hydr)oxides are key phases for the immobilisation of arsenic at the peat surface. In contrast, the deeper peat samples are dominated by arsenic sulphides (arsenopyrite, realgar and orpiment). Given that these peats receive inputs solely from the atmosphere, the presence of these sulphide phases suggests an in-situ authigenic formation. Redox oscillations in the peat due to a fluctuating water table and an abundant store of legacy sulphur from historic acid rain inputs may favour the precipitation of arsenic sequestering sulphides in sub-surface horizons. Oxidation-induced loss of these arsenic sequestering sulphur species by water table drawdown has important implications for the mobility of arsenic and the quality of waters draining peatlands.

Spectral and chemical characterization of jarosite in a palaeolacustrine depositional environment in Warkalli Formation in Kerala, South India and its implications

NASA Astrophysics Data System (ADS)

Singh, Mahima; Rajesh, V. J.; Sajinkumar, K. S.; Sajeev, K.; Kumar, S. N.

2016-11-01

Coastal cliffs fringing the Arabian Sea near Varkala exhibits the Warkalli Formation of the Tertiary sequence of Kerala, South India, with well-marked occurrence of jarosite associated with other hydrous mineral phases of phyllosilicate family in a palaeo-lacustrine depositional environment. Sandy phyllosilicates dominate the mineral assemblage, but jarosite occurs as a prominent secondary phase formed during acid-sulphate alteration of iron sulphide in this area. Here, we discuss about the potentiality of spectroscopic techniques to identify the possible mineral phases in the collected samples. The samples from the coastal cliffs have been characterized by hyperspectral analysis (VIS-NIR-SWIR), X-ray Diffraction (XRD), Fourier Transform Infra-red Reflectance (FTIR), Electron Probe Microanalysis (EPMA) and Laser Raman spectroscopy. The spectral and chemical analyses have confirmed the jarosite as natrojarosite and phyllosilicate as kaolinite. Other accessory phases have also been identified through XRD. FTIR spectroscopy has played a major role in identifying the major hydrous bonds between the minerals. VIS-NIR-SWIR spectra show several optimum spectral features at 910 nm, 1470 nm, 1849-1864 nm (in the form of a doublet), 1940 nm and 2270 nm, which could be utilised to locate jarosite in the remotely-sensed data. X-ray diffraction peaks helped in the identification of maximum number of minerals (kaolinite, smectite, quartz, feldspar, pyrite, marcasite and hematite) and the variation in jarosite content in the samples. We propose the formation of jarosite in the region by a seasonal, local and temporary development of acidic conditions. Abundance of organic matter in a fluvio-lacustrine environment has developed anaerobic conditions by removing available oxygen through decomposition of organic matter containing sulphur compounds. The sulphur thus liberated combines with hydrogen from water to develop acidic conditions and resulted in the formation of jarosite. The occurrence of jarosite in Warkalli Formation suggests on and off supply of water during diagenesis. Jarosite has been detected as a prominent deposit in several regions on Mars by Mars Exploration rover Opportunity and Mars Reconnaissance Orbiter-Compact Reconnaissance Imaging Spectrometer for Mars (CRISM). This study of jarosite formation in terrestrial environment will influence our understanding on the mineral precipitation, diagenesis and hydration processes on Mars. Additionally, it also shows the importance of spectroscopic techniques like Raman spectrometry to be used in future missions to Mars to further validate the results of orbital spectroscopy.

Documenting the diet in ancient human populations through stable isotope analysis of hair.

PubMed

Macko, S A; Engel, M H; Andrusevich, V; Lubec, G; O'Connell, T C; Hedges, R E

1999-01-29

Fundamental to the understanding of human history is the ability to make interpretations based on artefacts and other remains which are used to gather information about an ancient population. Sequestered in the organic matrices of these remains can be information, for example, concerning incidence of disease, genetic defects and diet. Stable isotopic compositions, especially those made on isolates of collagen from bones, have been used to help suggest principal dietary components. A significant problem in the use of collagen is its long-term stability, and the possibility of isotopic alteration during early diagenesis, or through contaminating condensation reactions. In this study, we suggest that a commonly overlooked material, human hair, may represent an ideal material to be used in addressing human diets of ancient civilizations. Through the analysis of the amino-acid composition of modern hair, as well as samples that were subjected to radiation (thus simulating ageing of the hair) and hair from humans that is up to 5200 years old, we have observed little in the way of chemical change. The principal amino acids observed in all of these samples are essentially identical in relative abundances and content. Dominating the compositions are serine, glutamic acid, threonine, glycine and leucine, respectively accounting for approximately 15%, 17%, 10%, 8% and 8% of the total hydrolysable amino acids. Even minor components (for example, alanine, valine, isoleucine) show similar constancy between the samples of different ages. This constancy clearly indicates minimal alteration of the amino-acid composition of the hair. Further, it would indicate that hair is well preserved and is amenable to isotopic analysis as a tool for distinguishing sources of nutrition. Based on this observation, we have isotopically characterized modern individuals for whom the diet has been documented. Both stable nitrogen and carbon isotope compositions were assessed, and together provide an indication of trophic status, and principal type (C3 or C4) of vegetation consumed. True vegans have nitrogen isotope compositions of about 7/1000 whereas humans consuming larger amounts of meat, eggs, or milk are more enriched in the heavy nitrogen isotope. We have also analysed large cross-sections of modern humans from North America and Europe to provide an indication of the variability seen in a population (the supermarket diet). There is a wide diversity in both carbon and nitrogen isotope values based at least partially on the levels of seafood, corn-fed beef and grains in the diets. Following analysis of the ancient hair, we have observed similar trends in certain ancient populations. For example, the Coptics of Egypt (1000 BP) and Chinchorro of Chile (5000-800 BP) have diets of similar diversity to those observed in the modern group but were isotopically influenced by local nutritional sources. In other ancient hair (Egyptian Late Middle Kingdom mummies, ca. 4000 BP), we have observed a much more uniform isotopic signature, indicating a more constant diet. We have also recognized a primary vegetarian component in the diet of the Neolithic Ice Man of the Oetztaler Alps (5200 BP). In certain cases, it appears that sulphur isotopes may help to further constrain dietary interpretations, owing to the good preservation and sulphur content of hair. It appears that analysis of the often-overlooked hair in archaeological sites may represent a significant new approach for understanding ancient human communities.

Documenting the diet in ancient human populations through stable isotope analysis of hair.

PubMed Central

Macko, S A; Engel, M H; Andrusevich, V; Lubec, G; O'Connell, T C; Hedges, R E

1999-01-01

Fundamental to the understanding of human history is the ability to make interpretations based on artefacts and other remains which are used to gather information about an ancient population. Sequestered in the organic matrices of these remains can be information, for example, concerning incidence of disease, genetic defects and diet. Stable isotopic compositions, especially those made on isolates of collagen from bones, have been used to help suggest principal dietary components. A significant problem in the use of collagen is its long-term stability, and the possibility of isotopic alteration during early diagenesis, or through contaminating condensation reactions. In this study, we suggest that a commonly overlooked material, human hair, may represent an ideal material to be used in addressing human diets of ancient civilizations. Through the analysis of the amino-acid composition of modern hair, as well as samples that were subjected to radiation (thus simulating ageing of the hair) and hair from humans that is up to 5200 years old, we have observed little in the way of chemical change. The principal amino acids observed in all of these samples are essentially identical in relative abundances and content. Dominating the compositions are serine, glutamic acid, threonine, glycine and leucine, respectively accounting for approximately 15%, 17%, 10%, 8% and 8% of the total hydrolysable amino acids. Even minor components (for example, alanine, valine, isoleucine) show similar constancy between the samples of different ages. This constancy clearly indicates minimal alteration of the amino-acid composition of the hair. Further, it would indicate that hair is well preserved and is amenable to isotopic analysis as a tool for distinguishing sources of nutrition. Based on this observation, we have isotopically characterized modern individuals for whom the diet has been documented. Both stable nitrogen and carbon isotope compositions were assessed, and together provide an indication of trophic status, and principal type (C3 or C4) of vegetation consumed. True vegans have nitrogen isotope compositions of about 7/1000 whereas humans consuming larger amounts of meat, eggs, or milk are more enriched in the heavy nitrogen isotope. We have also analysed large cross-sections of modern humans from North America and Europe to provide an indication of the variability seen in a population (the supermarket diet). There is a wide diversity in both carbon and nitrogen isotope values based at least partially on the levels of seafood, corn-fed beef and grains in the diets. Following analysis of the ancient hair, we have observed similar trends in certain ancient populations. For example, the Coptics of Egypt (1000 BP) and Chinchorro of Chile (5000-800 BP) have diets of similar diversity to those observed in the modern group but were isotopically influenced by local nutritional sources. In other ancient hair (Egyptian Late Middle Kingdom mummies, ca. 4000 BP), we have observed a much more uniform isotopic signature, indicating a more constant diet. We have also recognized a primary vegetarian component in the diet of the Neolithic Ice Man of the Oetztaler Alps (5200 BP). In certain cases, it appears that sulphur isotopes may help to further constrain dietary interpretations, owing to the good preservation and sulphur content of hair. It appears that analysis of the often-overlooked hair in archaeological sites may represent a significant new approach for understanding ancient human communities. PMID:10091248

Electrochemical incineration of wastes

NASA Technical Reports Server (NTRS)

Bhardwaj, R. C.; Sharma, D. K.; Bockris, J. OM.

1990-01-01

The novel technology of waste removal in space vehicles by electrochemical methods is presented to convert wastes into chemicals that can be eventually recycled. The important consideration for waste oxidation is to select a right kind of electrode (anode) material that should be stable under anodic conditions and also a poor electrocatalyst for oxygen and chlorine evolution. On the basis of long term electrolysis experiments on seven different electrodes and on the basis of total organic carbon reduced, two best electrodes were identified. The effect of redox ions on the electrolyte was studied. Though most of the experiments were done in mixtures of urine and waste, the experiments with redox couples involved 2.5 M sulfuric acid in order to avoid the precipitation of redox ions by urea. Two methods for long term electrolysis of waste were investigated: (1) the oxidation on Pt and lead dioxide electrodes using the galvanostatic methods; and (2) potentiostatic method on other electrodes. The advantage of the first method is the faster rate of oxidation. The chlorine evolution in the second method is ten times less then in the first. The accomplished research has shown that urine/feces mixtures can be oxidized to carbon dioxide and water, but current densities are low and must be improved. The perovskite and Ti4O7 coated with RuO2 are the best electrode materials found. Recent experiment with the redox agent improves the current density, however, sulphuric acid is required to keep the redox agent in solution to enhance oxidation effectively. It is desirable to reduce the use of acid and/or find substitutes.

Pharmacometabolomic Signature of Ataxia SCA1 Mouse Model and Lithium Effects

PubMed Central

Wikoff, William R.; Gatchel, Jennifer R.; Wang, Lu; Barupal, Dinesh K.; Crespo-Barreto, Juan; Fiehn, Oliver

2013-01-01

We have shown that lithium treatment improves motor coordination in a spinocerebellar ataxia type 1 (SCA1) disease mouse model (Sca1154Q/+). To learn more about disease pathogenesis and molecular contributions to the neuroprotective effects of lithium, we investigated metabolomic profiles of cerebellar tissue and plasma from SCA1-model treated and untreated mice. Metabolomic analyses of wild-type and Sca1154Q/+ mice, with and without lithium treatment, were performed using gas chromatography time-of-flight mass spectrometry and BinBase mass spectral annotations. We detected 416 metabolites, of which 130 were identified. We observed specific metabolic perturbations in Sca1154Q/+ mice and major effects of lithium on metabolism, centrally and peripherally. Compared to wild-type, Sca1154Q/+ cerebella metabolic profile revealed changes in glucose, lipids, and metabolites of the tricarboxylic acid cycle and purines. Fewer metabolic differences were noted in Sca1154Q/+ mouse plasma versus wild-type. In both genotypes, the major lithium responses in cerebellum involved energy metabolism, purines, unsaturated free fatty acids, and aromatic and sulphur-containing amino acids. The largest metabolic difference with lithium was a 10-fold increase in ascorbate levels in wild-type cerebella (p<0.002), with lower threonate levels, a major ascorbate catabolite. In contrast, Sca1154Q/+ mice that received lithium showed no elevated cerebellar ascorbate levels. Our data emphasize that lithium regulates a variety of metabolic pathways, including purine, oxidative stress and energy production pathways. The purine metabolite level, reduced in the Sca1154Q/+ mice and restored upon lithium treatment, might relate to lithium neuroprotective properties. PMID:23936457

Recovery TiO2 by leaching process of carbothermic reduced Kalimantan ilmenite

NASA Astrophysics Data System (ADS)

Wahyuningsih, S.; Sari, P. P.; Ramelan, A. H.

2018-05-01

Ilmenite naturally occurred in iron titanate (FeTiO3) minerals. The separation of natural ilmenite into TiO2 and Fe2O3 need to be explored to gain the high purity separation product. A new combination method named of carbothermic reduction, acidic-leaching and complexation by EDTA were proposed for separation TiO2 from Ilmenite. Roasting of ilmenite was carried out at 950 °C for 1 h by the addition of activated carbon with mass ratio of ilmenite : activated carbon =4:3. The carbothermic reduction was carried out to yield a high separation of initial content of ilmenite that will be easily to dissolve within hydrochloric acid solution in leaching process. The composition of ilmenite observed by X-Ray Fluoresences (XRF) changed after the carbothermic reduction process and the dominant content is TiO2 (57.56%). X-Ray Diffraction (XRD) of roasted ilmenite composed of decomposed product of ilmenite i.e. hematite (Fe2O3), TiO2 anatase, TiO2 rutile, and inorganic salt. The leaching of the roasted ilmenite has been done by sulphuric acid solution (6 M) to gain the titanyl sulphate solution. Separation of iron impurities of TiO2 gel from titanyl sulphate (TiOSO4) solution was conducted by complexation method using EDTA as a complexation agent. The characteristic of TiO2 obtained using XRD showed that TiO2 is anatase type and the percentage of TiO2 using XRF showed that TiO2 content of 86,03%.

Characterization of C-S lyase from Lactobacillus delbrueckii subsp. bulgaricus ATCC BAA-365 and its potential role in food flavour applications.

PubMed

Allegrini, Alessandra; Astegno, Alessandra; La Verde, Valentina; Dominici, Paola

2017-04-01

Volatile thiols have substantial impact on the aroma of many beverages and foods. Thus, the control of their formation, which has been linked to C-S lyase enzymatic activities, is of great significance in industrial applications involving food flavours. Herein, we have carried out a spectroscopic and functional characterization of a putative pyridoxal 5'-phosphate (PLP)-dependent C-S lyase from the lactic acid bacterium Lactobacillus delbrueckii subsp. bulgaricus ATCC BAA-365 (LDB C-S lyase). Recombinant LDB C-S lyase exists as a tetramer in solution and shows spectral properties of enzymes containing PLP as cofactor. The enzyme has a broad substrate specificity toward sulphur-containing amino acids with aminoethyl-L-cysteine and L-cystine being the most effective substrates over L-cysteine and L-cystathionine. Notably, the protein also reveals cysteine-S-conjugate β-lyase activity in vitro, and is able to cleave a cysteinylated substrate precursor into the corresponding flavour-contributing thiol, with a catalytic efficiency higher than L-cystathionine. Contrary to similar enzymes of other lactic acid bacteria however, LDB C-S lyase is not capable of α,γ-elimination activity towards L-methionine to produce methanethiol, which is a significant compound in flavour development. Based on our results, future developments can be expected regarding the flavour-forming potential of Lactobacillus C-S lyase and its use in enhancing food flavours. © The Authors 2017. Published by Oxford University Press on behalf of the Japanese Biochemical Society. All rights reserved.

Control of resin production in Araucaria angustifolia, an ancient South American conifer.

PubMed

Perotti, J C; da Silva Rodrigues-Corrêa, K C; Fett-Neto, A G

2015-07-01

Araucaria angustifolia is an ancient slow-growing conifer that characterises parts of the Southern Atlantic Forest biome, currently listed as a critically endangered species. The species also produces bark resin, although the factors controlling its resinosis are largely unknown. To better understand this defence-related process, we examined the resin exudation response of A. angustifolia upon treatment with well-known chemical stimulators used in fast-growing conifers producing both bark and wood resin, such as Pinus elliottii. The initial hypothesis was that A. angustifolia would display significant differences in the regulation of resinosis. The effect of Ethrel(®) (ET - ethylene precursor), salicylic acid (SA), jasmonic acid (JA), sulphuric acid (SuA) and sodium nitroprusside (SNP - nitric oxide donor) on resin yield and composition in young plants of A. angustifolia was examined. In at least one of the concentrations tested, and frequently in more than one, an aqueous glycerol solution applied on fresh wound sites of the stem with one or more of the adjuvants examined promoted an increase in resin yield, as well as monoterpene concentration (α-pinene, β-pinene, camphene and limonene). Higher yields and longer exudation periods were observed with JA and ET, another feature shared with Pinus resinosis. The results suggest that resinosis control is similar in Araucaria and Pinus. In addition, A. angustifolia resin may be a relevant source of valuable terpene chemicals, whose production may be increased by using stimulating pastes containing the identified adjuvants. © 2014 German Botanical Society and The Royal Botanical Society of the Netherlands.

Remediation of uranium in-situ leaching area at Straz Pod Ralskem, Czech Republic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vokal, Vojtech; Muzak, Jiri; Ekert, Vladimir

2013-07-01

A large-scale development in exploration and production of uranium ores in the Czech Republic was done in the 2nd half of the 20. century. Many uranium deposits were discovered in the territory of the Czech Republic. One of the most considerable deposits in the Czech Republic is the site Hamr na Jezere - Straz pod Ralskem where both mining methods - the underground mining and the acidic in-situ leaching - were used. The extensive production of uranium led to widespread environmental impacts and contamination of ground waters. Over the period of 'chemical' leaching of uranium (ca. 32 years), a totalmore » of more than 4 million tons of sulphuric acid and other chemicals have been injected into the ground. Most of the products (approx. 99.5 %) of the acids reactions with the rocks are located in the Cenomanian aquifer. The contamination of Cenomanian aquifer covers the area larger then 27 km{sup 2}. The influenced volume of groundwater is more than 380 million m{sup 3}. The total amount of dissolved SO{sub 4}{sup 2-} is about 3.6 million tons. After 1990 a large-scale environmental program was established and the Czech government decided to liquidate the ISL Mine and start the remediation in 1996. The remediation consists of contaminated groundwater pumping, removing of the contaminants and discharging or reinjection of treated water. Nowadays four main remedial technological installations with sufficient capacity for reaching of the target values of remedial parameters in 2037 are used - the 'Station for Acid Solutions Liquidation No. One', the 'Mother liquor reprocessing' station, the 'Neutralization and Decontamination Station NDS 6' and the 'Neutralization and Decontamination Station NDS 10'. It is expected that the amount of withdrawn contaminants will vary from 80 000 to 120 000 tons per year. Total costs of all remediation activities are expected to be in excess of 2 billion EUR. (authors)« less

Response of surface water chemistry to reduced levels of acid precipitation: Comparison of trends in two regions of New York, USA

USGS Publications Warehouse

Burns, Douglas A.; McHale, M.R.; Driscoll, C.T.; Roy, K.M.

2006-01-01

In light of recent reductions in sulphur (S) and nitrogen (N) emissions mandated by Title IV of the Clean Air Act Amendments of 1990, temporal trends and trend coherence in precipitation (1984-2001 and 1992-2001) and surface water chemistry (1992-2001) were determined in two of the most acid-sensitive regions of North America, i.e. the Catskill and Adirondack Mountains of New York. Precipitation chemistry data from six sites located near these regions showed decreasing sulphate (SO42-), nitrate (NO3-), and base cation (CB) concentrations and increasing pH during 1984-2001, but few significant trends during 1992-2001. Data from five Catskill streams and 12 Adirondack lakes showed decreasing trends in SO42- concentrations at all sites, and decreasing trends in NO3-, CB, and H+ concentrations and increasing trends in dissolved organic carbon at most sites. In contrast, acid-neutralizing capacity (ANC increased significantly at only about half the Adirondack lakes and in one of the Catskill streams. Flow correction prior to trend analysis did not change any trend directions and had little effect on SO42- trends, but it caused several significant non-flow-corrected trends in NO3- and ANC to become non-significant, suggesting that trend results for flow-sensitive constituents are affected by flow-related climate variation. SO42- concentrations showed high temporal coherence in precipitation, surface waters, and in precipitation-surface water comparisons, reflecting a strong link between S emissions, precipitation SO42- concentrations, and the processes that affect S cycling within these regions. NO3- and H+ concentrations and ANC generally showed weak coherence, especially in surface waters and in precipitation-surface water comparisons, indicating that variation in local-scale processes driven by factors such as climate are affecting trends in acid-base chemistry in these two regions. Copyright ?? 2005 John Wiley & Sons, Ltd.

High-resolution metabolomics of occupational exposure to trichloroethylene

PubMed Central

Walker, Douglas I; Uppal, Karan; Zhang, Luoping; Vermeulen, Roel; Smith, Martyn; Hu, Wei; Purdue, Mark P; Tang, Xiaojiang; Reiss, Boris; Kim, Sungkyoon; Li, Laiyu; Huang, Hanlin; Pennell, Kurt D; Jones, Dean P; Rothman, Nathaniel; Lan, Qing

2016-01-01

Background: Occupational exposure to trichloroethylene (TCE) has been linked to adverse health outcomes including non-Hodgkin’s lymphoma and kidney and liver cancer; however, TCE’s mode of action for development of these diseases in humans is not well understood. Methods: Non-targeted metabolomics analysis of plasma obtained from 80 TCE-exposed workers [full shift exposure range of 0.4 to 230 parts-per-million of air (ppma)] and 95 matched controls were completed by ultra-high resolution mass spectrometry. Biological response to TCE exposure was determined using a metabolome-wide association study (MWAS) framework, with metabolic changes and plasma TCE metabolites evaluated by dose-response and pathway enrichment. Biological perturbations were then linked to immunological, renal and exposure molecular markers measured in the same population. Results: Metabolic features associated with TCE exposure included known TCE metabolites, unidentifiable chlorinated compounds and endogenous metabolites. Exposure resulted in a systemic response in endogenous metabolism, including disruption in purine catabolism and decreases in sulphur amino acid and bile acid biosynthesis pathways. Metabolite associations with TCE exposure included uric acid (β = 0.13, P-value = 3.6 × 10−5), glutamine (β = 0.08, P-value = 0.0013), cystine (β = 0.75, P-value = 0.0022), methylthioadenosine (β = −1.6, P-value = 0.0043), taurine (β = −2.4, P-value = 0.0011) and chenodeoxycholic acid (β = −1.3, P-value = 0.0039), which are consistent with known toxic effects of TCE, including immunosuppression, hepatotoxicity and nephrotoxicity. Correlation with additional exposure markers and physiological endpoints supported known disease associations. Conclusions: High-resolution metabolomics correlates measured occupational exposure to internal dose and metabolic response, providing insight into molecular mechanisms of exposure-related disease aetiology. PMID:27707868

High-resolution metabolomics of occupational exposure to trichloroethylene.

PubMed

Walker, Douglas I; Uppal, Karan; Zhang, Luoping; Vermeulen, Roel; Smith, Martyn; Hu, Wei; Purdue, Mark P; Tang, Xiaojiang; Reiss, Boris; Kim, Sungkyoon; Li, Laiyu; Huang, Hanlin; Pennell, Kurt D; Jones, Dean P; Rothman, Nathaniel; Lan, Qing

2016-10-01

Occupational exposure to trichloroethylene (TCE) has been linked to adverse health outcomes including non-Hodgkin's lymphoma and kidney and liver cancer; however, TCE's mode of action for development of these diseases in humans is not well understood. Non-targeted metabolomics analysis of plasma obtained from 80 TCE-exposed workers [full shift exposure range of 0.4 to 230 parts-per-million of air (ppm a )] and 95 matched controls were completed by ultra-high resolution mass spectrometry. Biological response to TCE exposure was determined using a metabolome-wide association study (MWAS) framework, with metabolic changes and plasma TCE metabolites evaluated by dose-response and pathway enrichment. Biological perturbations were then linked to immunological, renal and exposure molecular markers measured in the same population. Metabolic features associated with TCE exposure included known TCE metabolites, unidentifiable chlorinated compounds and endogenous metabolites. Exposure resulted in a systemic response in endogenous metabolism, including disruption in purine catabolism and decreases in sulphur amino acid and bile acid biosynthesis pathways. Metabolite associations with TCE exposure included uric acid (β = 0.13, P-value = 3.6 × 10 -5 ), glutamine (β = 0.08, P-value = 0.0013), cystine (β = 0.75, P-value = 0.0022), methylthioadenosine (β = -1.6, P-value = 0.0043), taurine (β = -2.4, P-value = 0.0011) and chenodeoxycholic acid (β = -1.3, P-value = 0.0039), which are consistent with known toxic effects of TCE, including immunosuppression, hepatotoxicity and nephrotoxicity. Correlation with additional exposure markers and physiological endpoints supported known disease associations. High-resolution metabolomics correlates measured occupational exposure to internal dose and metabolic response, providing insight into molecular mechanisms of exposure-related disease aetiology. © The Author 2016; all rights reserved. Published by Oxford University Press on behalf of the International Epidemiological Association.

Tithonia diversifolia as a Supplementary Feed for Dairy Cows

PubMed Central

Ribeiro, Rafael Sandin; Terry, Stephanie Amelia; Sacramento, João Paulo; Silveira, Sylvia Rocha e; Bento, Cláudia Braga Pereira; da Silva, Elsa Fernandes; Mantovani, Hilário Cuquetto; da Gama, Marco Antônio Sundfeld; Pereira, Luiz Gustavo Ribeiro; Tomich, Thierry Ribeiro; Maurício, Rogério Martins

2016-01-01

The objective of this study was to examine the effects of Tithonia diversifolia as a supplementary forage on dairy cow performance and methane production. Nine lactating Holstein × Zebu dairy cows (519 ± 53.3 kg of body weight and 66 ± 13.3 d in milk) were paired by milk yield (21.3 ± 2.34 kg/d) and body weight and randomly assigned to three dietary treatments in a Latin square design with 21-d experimental periods (14 d for diet adaptation and 7 d for measurements and sample collection). The dietary treatments included the control diet consisting of fresh sugar cane plus concentrate (44:56, % of diet DM), and two treatment diets containing different levels of fresh T. diversifolia (6.5 and 15.4%, DM basis) which partially replaced both sugarcane and concentrates. Methane production was measured using the sulphur hexafluoride (SF6) technique from d 16 to d 21 of each experimental period. Analysis of the gas samples was performed by gas chromatography. The inclusion of T. diversifolia at 15.4% DM had no effects on DM intake, milk production, nitrogen balance or methane production. There was no effect on the concentrations of total saturated fatty acids (SFA), monounsaturated fatty acids (MUFA), and polyunsaturated fatty acids (PUFA) in milk fat (P ≥ 0.28), though individual milk fatty acids were affected. Serum concentrations of glucose, urea nitrogen (BUN), triglycerides, β-hydroxybutyrate (BHBA), and cholesterol were unaffected by the dietary treatments (P ≥ 0.13). There was a time (2 and 6 h post-feeding) and dietary treatment effect (P < 0.01) on the acetate to propionate ratio in the rumen. A denaturing gradient gel electrophoresis analysis of the archaeal community showed distinct clustering of the archaea populations for control and treatment diets. Taken together, our results indicate the potential of T. diversifolia as a supplementary forage for dairy cattle in the tropics. PMID:27906983

Response of pore water Al, Fe and S concentrations to waterlogging in a boreal acid sulphate soil.

PubMed

Virtanen, Seija; Simojoki, Asko; Hartikainen, Helinä; Yli-Halla, Markku

2014-07-01

Environmental hazards caused by acid sulphate (AS) soils are of worldwide concern. Among various mitigation measures, waterlogging has mainly been studied in subtropical and tropical conditions. To assess the environmental relevance of waterlogging as a mitigation option in boreal AS soils, we arranged a 2.5-year experiment with monolithic lysimeters to monitor changes in the soil redox potential, pH and the concentrations of aluminium (Al), iron (Fe) and sulphur (S) in pore water in response to low and high groundwater levels in four AS soil horizons. The monoliths consisted of acidic oxidized B horizons and a reduced C horizon containing sulphidic material. Eight lysimeters were cropped (reed canary grass, Phalaris arundinacea) and two were bare without a crop. Waterlogging was conducive to reduction reactions causing a slight rise in pH, a substantial increase in Fe (Fepw) and a decrease in Al (Alpw) in the pore water. The increase in Fepw was decisively higher in the cropped waterlogged lysimeters than in the bare ones, which was attributable to the microbiologically catalysed reductive dissolution of poorly ordered iron oxides and secondary minerals. In contrast to warmer climates, Fepw concentrations remained high throughout the experiment, indicating that the reduction was poised in the iron range, while sulphate was not reduced to sulphide. Therefore, the precipitation of iron sulphide was negligible in the environment with a low pH and abundant with poorly ordered Fe oxides. Increased Fe in pore water counteracts the positive effects of waterlogging, when water is flushed from fields to watercourses, where re-oxidation of Fe causes acidity and oxygen depletion. However, waterlogging prevented further oxidation of sulphidic materials and decreased Alpw to one-tenth of the initial concentrations, and even to one-hundredth of the levels in the low water table lysimeters. Copyright © 2014 Elsevier B.V. All rights reserved.

Intensification of biodiesel production from soybean oil and waste cooking oil in the presence of heterogeneous catalyst using high speed homogenizer.

PubMed

Joshi, Saurabh; Gogate, Parag R; Moreira, Paulo F; Giudici, Reinaldo

2017-11-01

In the present work, high speed homogenizer has been used for the intensification of biodiesel synthesis from soybean oil and waste cooking oil (WCO) used as a sustainable feedstock. High acid value waste cooking oil (27mg of KOH/g of oil) was first esterified with methanol using sulphuric acid as catalyst in two stages to bring the acid value to desired value of 1.5mg of KOH/g of oil. Transesterification of soybean oil (directly due to lower acid value) and esterified waste cooking oil was performed in the presence of heterogeneous catalyst (CaO) for the production of biodiesel. Various experiments were performed for understanding the effect of operating parameters viz. molar ratio, catalyst loading, reaction temperature and speed of rotation of the homogenizer. For soybean oil, the maximum biodiesel yield as 84% was obtained with catalyst loading of 3wt% and molar ratio of oil to methanol of 1:10 at 50°C with 12,000rpm as the speed of rotation in 30min. Similarly biodiesel yield of 88% was obtained from waste cooking oil under identical operating conditions except for the catalyst loading which was 1wt%. Significant increase in the rate of biodiesel production with yields from soybean oil as 84% (in 30min) and from WCO as 88% (30min) was established due to the use of high speed homogenizer as compared to the conventional stirring method (requiring 2-3h for obtaining similar biodiesel yield). The observed intensification was attributed to the turbulence caused at microscale and generation of fine emulsions due to the cavitational effects. Overall it can be concluded from this study that high speed homogenizer can be used as an alternate cavitating device to efficiently produce biodiesel in the presence of heterogeneous catalysts. Copyright © 2017 Elsevier B.V. All rights reserved.

SULPHUR DIOXIDE LEACHING OF URANIUM CONTAINING MATERIAL

DOEpatents

Thunaes, A.; Rabbits, F.T.; Hester, K.D.; Smith, H.W.

1958-12-01

A process is described for extracting uranlum from uranium containing material, such as a low grade pitchblende ore, or mill taillngs, where at least part of the uraniunn is in the +4 oxidation state. After comminuting and magnetically removing any entrained lron particles the general material is made up as an aqueous slurry containing added ferric and manganese salts and treated with sulfur dioxide and aeration to an extent sufficient to form a proportion of oxysulfur acids to give a pH of about 1 to 2 but insufficient to cause excessive removal of the sulfur dioxide gas. After separating from the solids, the leach solution is adjusted to a pH of about 1.25, then treated with metallic iron in the presence of a precipitant such as a soluble phosphate, arsonate, or fluoride.

Bionanocomposites produced from cassava starch and oil palm mesocarp cellulose nanowhiskers.

PubMed

Campos, Adriana de; Sena Neto, Alfredo R de; Rodrigues, Vanessa B; Luchesi, Bruno R; Moreira, Francys K V; Correa, Ana Carolina; Mattoso, Luiz H C; Marconcini, José M

2017-11-01

Cassava starch films reinforced with cellulose nanowhiskers from oil palm mesocarp fibers were produced by casting. Nanowhiskers were obtained by sulphuric acid hydrolysis followed by microfluidization and incorporated in starch films at various loadings (1-10wt%). Morphological and mechanical characterizations showed that the reinforcing effect of oil palm cellulose nanowhiskers was significant at loadings of up to 6wt%, which was determined to be the nanowhiskers percolation threshold. Above this content, formation of agglomerates became more significant, causing a decrease in mechanical properties of starch bionanocomposites. Below percolation threshold, such as 2wt%, elongation at break increased by 70%, showing an effective reinforcing effect. Dynamic mechanical analyses revealed filler/matrix interactions through hydrogen bonding in bionanocomposites. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of Biomass Pretreatment Process Time on Furfural Extraction from Birch Wood

NASA Astrophysics Data System (ADS)

Brazdausks, Prans; Puke, Maris; Vedernikovs, Nikolajs; Kruma, Irena

2013-12-01

Furfural is a biomass derived-chemical that can be used to replace petrochemicals. In this study, dilute sulphuric acid hydrolysis was used for hemicelluloses secession from birch wood. The reaction was investigated at different biomass treatment times (10-90 min, increasing it by 10 min). We found that the greatest amount of furfural 1.4-2.6%, which is 9.7-17.7% from theoretical possible yield, was formed in the first 30 min of the beginning of birch wood pentoses monosaccharide dehydration, but the greatest yield of furfural 10.3%, which is 70.0% from the theoretical yield, can be obtained after 90 min. Given that furfural yield generally does not exceed 50% from the theoretical amount, the result can be considered as very good.

Soluble organic matrices of aragonitic skeletons of Merulinidae (Cnidaria, Anthozoa).

PubMed

Dauphin, Yannicke; Cuif, Jean-Pierre; Williams, C Terry

2008-05-01

Our interpretation of the overall taxonomy and evolution of the Scleractinia, the most important reef builders in tropical areas, has long depended exclusively on morphology of the calcareous skeletons. The reported series of physical and biochemical characterizations of skeletons and the mineralizing matrices extracted from the skeletons allow, for the first time, the level of biochemical diversity among corallites of the same family to be estimated. Similarities and differences observed in the micro- and nanostructures of the skeletons reflect those of the soluble organic matrices. Sulphur is mainly associated with sulphated acidic sugars. The role of sulphated sugars on the biomineralization processes is still underestimated. The resulting data suggest that environmental conditions may act on the mineralization process through the detailed compositions of the mineralizing matrices.

Changes in oral trace gas concentrations following orthognathic surgery and intermaxillary fixation: a case study using selected ion flow tube mass spectrometry

PubMed Central

Ross, Brian M

2011-01-01

Orthognathic surgery is frequently accompanied by intermaxillary fixation. Intermaxillary fixation impedes the maintenance of effective oral hygiene and prolonged fixation can result in periodontal disease. A potential shorter term effect is the generation of oral malodour. It is unclear, however, as to how the production of malodorous compounds in the oral cavity is altered post-surgery. Oral air concentration of sulphur containing compounds, short chain organic acids, ammonia, isoprene and acetone were measured using selected ion flow tube-mass spectrometry in a patient who had undergone orthognathic surgery with subsequent intermaxillary fixation. Total sulphide levels rose approximately 5-fold during fixation with metal ties, with smaller increases recorded for the other compounds measured with the exception of isoprene which remained close to baseline levels. Organic acid levels declined markedly once elastic ties had replaced metal ties, with a lesser reduction being observed in sulphide levels, with both declining further after the commencement of a chlorhexidine-containing mouthwash. These data suggest that bacterial generation of a variety of malodorous compounds increases markedly following intermaxillary fixation. This single case also suggests that the use of elastic ties and effective oral hygiene techniques, including the use of chlorhexidine mouthwash, may help ameliorate such post-surgical effects. PMID:21789965

A new process for nickel ammonium disulfate production from ash of the hyperaccumulating plant Alyssum murale.

PubMed

Barbaroux, R; Plasari, E; Mercier, G; Simonnot, M O; Morel, J L; Blais, J F

2012-04-15

The extraction of nickel (Ni) from ultramafic soils by phytomining can be achieved using Alyssum murale cultures. This study presents a new process for the valorization of Ni accumulated by this plant through the production of a Ni ammonium disulfate salt (Ni(NH(4))(2)(SO(4))(2).6H(2)O). The process comprises an initial leaching of the ashes of A. murale with a sulphuric acid solution (1.9 M H(2)SO(4), T=95 °C, t=240 min, TS=150 g ash L(-1)), producing a leachate rich in Ni (10.2 g Ni L(-1); 96% Ni solubilisation), Mg, P, K, Fe, Ca and Al. The pH of the acid leachate is increased to 5.0 with NaOH (5M), followed by an evaporation step which produced a purified solution rich in Ni (21.3 g NiL(-1)) and an iron hydroxide precipitate. The cold crystallization (T=2 °C, t=6h) of this solution by the stoichiometric addition (× 1.2) of ammonium sulfate generates a Ni ammonium disulfate salt, containing 13.2% Ni, that is potentially valuable to industry. Copyright © 2012 Elsevier B.V. All rights reserved.

Determination of trace concentrations of chlorine in aqueous solutions by high-resolution continuum source graphite furnace molecular absorption spectrometry

NASA Astrophysics Data System (ADS)

Machyňák, Ľubomír; Čacho, František; Němeček, Martin; Beinrohr, Ernest

2016-11-01

Trace concentrations of total chlorine were determined by means of molecular absorption of indium mono-chloride (InCl) at 267.217 nm using high-resolution continuum source graphite furnace molecular absorption spectrometry. The effects of chemical modifiers and the amount of In on the sensitivity and accuracy were investigated. The optimum pyrolysis and vaporization temperatures were 600 °C and 1400 °C, respectively. The limit of detection and characteristic mass were found to be 0.10 ng and 0.21 ng, respectively. Potential non-spectral and spectral interferences were tested for various metals and non-metals at concentrations up to 50 mg L- 1 and for phosphoric, sulphuric and nitric acids. No spectral interferences were observed. Significant non-spectral interferences were observed with F, Br, and I at concentrations higher than 1 mg L- 1, 5 mg L- 1 and 25 mg L- 1, respectively, which is probably caused by formation of competitive indium halogen molecules. Higher concentrations of mineral acids depressed the signal owing to the formation of volatile HCl. The calibration curve was linear in the range between 0.3 and 10 ng with a correlation coefficient of R = 0.993. The elaborated method was used for the chlorine determination in various waters and a drug sample.

Modelling the contribution of biogenic volatile organic compounds to new particle formation in the Jülich plant atmosphere chamber

NASA Astrophysics Data System (ADS)

Roldin, P.; Liao, L.; Mogensen, D.; Dal Maso, M.; Rusanen, A.; Kerminen, V.-M.; Mentel, T. F.; Wildt, J.; Kleist, E.; Kiendler-Scharr, A.; Tillmann, R.; Ehn, M.; Kulmala, M.; Boy, M.

2015-09-01

We used the Aerosol Dynamics gas- and particle-phase chemistry model for laboratory CHAMber studies (ADCHAM) to simulate the contribution of BVOC plant emissions to the observed new particle formation during photooxidation experiments performed in the Jülich Plant-Atmosphere Chamber and to evaluate how well smog chamber experiments can mimic the atmospheric conditions during new particle formation events. ADCHAM couples the detailed gas-phase chemistry from Master Chemical Mechanism with a novel aerosol dynamics and particle phase chemistry module. Our model simulations reveal that the observed particle growth may have either been controlled by the formation rate of semi- and low-volatility organic compounds in the gas phase or by acid catalysed heterogeneous reactions between semi-volatility organic compounds in the particle surface layer (e.g. peroxyhemiacetal dimer formation). The contribution of extremely low-volatility organic gas-phase compounds to the particle formation and growth was suppressed because of their rapid and irreversible wall losses, which decreased their contribution to the nano-CN formation and growth compared to the atmospheric situation. The best agreement between the modelled and measured total particle number concentration (R2 > 0.95) was achieved if the nano-CN was formed by kinetic nucleation involving both sulphuric acid and organic compounds formed from OH oxidation of BVOCs.

Morphological transformation of soot: investigation of microphysical processes during the condensation of sulphuric acid and limonene ozonolysis products vapours

NASA Astrophysics Data System (ADS)

Pathak, R. K. P.; Pei, X.; Hallquist, M.; Pagels, J. H.

2017-12-01

Morphological transformation of soot particle by condensation of low volatility materials on it is a dominant atmospheric process with serious implications for its optical and hygroscopic properties, and atmospheric lifetime. In this study, the morphological transformation of soot agglomerate under the influence of condensation of vapours of sulphuric acid, and/or limonene ozonolysis products were investigated systematically using a Differential Mobility Analyser-Aerosol Particle Mass Analyser (DMA-APM) and the Tandem DMA techniques integrated with a laminar flow-tube system. We discovered that the morphology transformation of soot in general was a sequence of two-step process, i.e. (i) filling of void space within soot agglomerate; (ii) growth of particle diameter. These two steps followed and complimented each other. In the very beginning the filling was the dominant process followed by growth until it led to the accumulation of enough material that in turn exerted surface forces that eventually facilitated the further filling. The filling of void space was constrained by the initial morphology of fresh soot and the nature and amount of the material condensed. This process continued in several sequential steps until all void space within the soot agglomerate was filled completely and then growth of a spherical particle continued as long as mass was condensed on it. In this study, we developed a framework to quantify the microphysical transformation of soot upon the condensation of various materials. The framework utilized experimental data and hypothesis of ideal sphere growth and filling of voids to quantify the distribution of condensed materials in these two processes complimenting each other. Using this framework, we have quantified the percentage of material that went into processes of particle growth and void filling at each step. Using the same framework, we further estimated the fraction of internal voids and open voids and used this information to derive the volume equivalent diameter of soot agglomerate containing internal voids and calculated in-situ dynamic shape factor. Our study is the first study that tracks in situ microphysical changes in soot morphology quantitatively, providing the detailed status of both fresh and coated soot particles.

Investigating the significance of zero-point motion in small molecular clusters of sulphuric acid and water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stinson, Jake L.; Kathmann, Shawn M.; Ford, Ian J.

2014-01-14

The nucleation of particles from trace gases in the atmosphere is an important source of cloud condensation nuclei (CCN), and these are vital for the formation of clouds in view of the high supersaturations required for homogeneous water droplet nucleation. The methods of quantum chemistry have increasingly been employed to model nucleation due to their high accuracy and efficiency in calculating configurational energies; and nucleation rates can be obtained from the associated free energies of particle formation. However, even in such advanced approaches, it is typically assumed that the nuclei have a classical nature, which is questionable for some systems.more » The importance of zero-point motion (also known as quantum nuclear dynamics) in modelling small clusters of sulphuric acid and water is tested here using the path integral molecular dynamics (PIMD) method at the density functional theory (DFT) level of theory. We observe a small zero-point effect on the the equilibrium structures of certain clusters. One configuration is found to display a bimodal behaviour at 300 K in contrast to the stable ionised state suggested from a zero temperature classical geometry optimisation. The general effect of zero-point motion is to promote the extent of proton transfer with respect to classical behaviour. We thank Prof. Angelos Michaelides and his group in University College London (UCL) for practical advice and helpful discussions. This work benefited from interactions with the Thomas Young Centre through seminar and discussions involving the PIMD method. SMK was supported by the U.S. Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. JLS and IJF were supported by the IMPACT scheme at UCL and by the U.S. Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. We are grateful for use of the UCL Legion High Performance Computing Facility and the resources of the National Energy Research Scientific Computing Center (NERSC), which is supported by the U.S. Department of Energy, Office of Science of the under Contract No. DE-AC02-05CH11231.« less

Intumescent Coatings as Fire Retardants

NASA Technical Reports Server (NTRS)

Parker, J. A.; Fohlen, G. M.; Sawko, P. M.; Fish, R. H.

1970-01-01

The development of fire-retardant coatings to protect surfaces which may be exposed to fire or extreme heat is a subject of intense interest to many industries. A fire-retardant paint has been developed which represents a new chemical approach for preparing intumescent coatings, and potentially, is very important to fire-prevention authorities. The requirements for a superior coating include ease of application, suitability to a wide variety of surfaces and finishes, and stability over an extended period of time within a broad range of ambient temperature and humidity conditions. These innovative coatings, when activated by the heat of a fire, react to form a thick, low-density, polymeric coating or char layer. Water vapor and sulphur dioxide are released during the intumescent reaction. Two fire-protection mechanisms thus become available: (1) the char layer retards the flow of heat, due to the extremely low thermal conductivity; and (2) water vapor and sulfur dioxide are released, providing fire quenching properties. Still another mechanism functions in cases where the char, by virtue of its high oxidation resistance and low thermal conductivity, reaches a sufficiently high temperature to re-radiate much of the incident heat load. The coatings consist of dispersions of selective salts of a nitro-amino-arornatic compound. Specifically, para-nitroaniline bisulfate and the ammonium salt of para-nitroaniline-ortho sulphuric acid (2-amino-5-nitrobenzenesulphuric acid) are used. Suitable vehicles are cellulose nitrate of lacquer grade, a nitrite-phenolic modified rubber, or epoxy-polysulfide copolymer. Three separate formulations have been developed. A solvent is usually employed, such as methylethyl ketone, butyl acetate, or toluene, which renders the coatings suitably thin and which evaporates after the coatings are applied. Generally, the intumescent material is treated as insoluble in the vehicle, and is ground and dispersed in the vehicle and solvent like an ordinary coating pigment. The char found on intumescence is better in terms of yield and physical properties than chars obtained from many previously known intumescent materials. Prior to intumescence, the coating has a density of 85 pounds per cubic foot. After intumescence, the density is approximately 0.3 pounds per cubic loot. The linear expansion of the coatings ranges from 70 to 200 times the applied coating thickness.

Thermodynamics at work - on the limits and potentials of biogeochemical processes

NASA Astrophysics Data System (ADS)

Peiffer, Stefan

2017-04-01

The preferential use of high potential electron acceptors by microorganisms has lead to the classical concept of a redox sequence with a sequential use of O2 nitrate, Fe(III), sulfate, and finally CO2 as electron acceptors for respiration (Stumm & Morgan, 1996). Christian Blodau has rigourously applied this concept to constrain the thermodynamical limits at which specific aquatic systems operate. In sediments from acidic mining lakes his analysis revealed that sulfate reducers are not competitive as long as low-crystallinity ferric oxides are available for organic matter decomposition (Blodau et al, 1998). This analysis opened up the possibility to generalize the linkage between the iron and sulphur cycle in such systems and to constrain the biogeochemical limits for remediation (e. g. Peine et al, 2000). In a similar approach, Beer & Blodau (2007) were able to demonstrate that constraints on the removal of products from acetoclastic methanogenesis in deeper peat layers are inhibiting organic matter decomposition and provide a thermodynamic argument for peat accumulation. In this contribution I will review such ideas and further refine the limits and potentials of biogeochemical reactions in terms of redox-active metastable phases (RAMPS) that are typically mixed-valent carbon-, iron-, and sulfur-containing compounds and which allow for the occurrence of a number of enigmatic reactions, e. g. limited greenhouse gas emission (CH4) under dynamic redox conditions. It is proposed that redox equivalents are generated, stored and recycled during oxidation and reduction cycles thus suppressing methanogenesis (Blodau, 2002). Such RAMPS will preferentially occur at dynamic interfaces being exposed to frequent redox cycles. The concept of RAMPS will be illustrated along the interaction between ferric (hydr)oxides and dissolved sulphide. Recent studies using modern analytical tools revealed the formation of a number of amorphous products within a short time scale (days) both on the Fe and S side (Peiffer & Wan, 2016; Wan et al, 2014) which will allow for the occurrence of cryptic sulphur cycles, i. e. high turnover of sulphide and sulfate without the appearance of dissolved sulphide species. References Beer, J; Blodau, C (2007): Transport and thermodynamics constrain belowground carbon turover in a northern peatland, Geochim. Cosmochim. Acta, 71, 2989-3002 Blodau, C. (2002). "Carbon cycling in peatlands: A review of processes and controls." Environmental Reviews 10(2): 111-134. Blodau, C; Hoffmann, S; Peine, A; Peiffer, S (1998): Iron and sulfate reduction in the sediments of acid mine lake 116 (Brandenburg, Germany): Rates and geochemical evaluation, Water, Air and Soil Pollution, 108, 249-270 Peiffer, S., Wan M. (2016) Reductive Dissolution and Reactivity of Ferric (Hydr)oxides, in Faivre, D., Iron Oxides: From Nature to Applications, Wiley-VCH, chapter 3, 29-51 Peine, A; Küsel, K; Tritschler, A; Peiffer, S (2000): Electron flow in an iron-rich acidic sedimant - evidence for an acidity-driven iron cycle, Limnol. Oceanogr., 45(5), 1077-1087 Stumm, W.; Morgan, J. J. (1996): Aquatic Chemistry, Wiley Wan, M., Shchukarev, A., Lohmayer, R., Planer-Friedrich, B., Peiffer, S. (2014) Occurrence of surface polysulfides during the interaction between ferric (hydr)oxides and aqueous sulfide. Environmental Science and Technology, 48, 5076-5084

Geothermal hydrology of Valles Caldera and the southwestern Jemez Mountains, New Mexico

USGS Publications Warehouse

Trainer, Frank W.; Rogers, Robert J.; Sorey, M.L.

2000-01-01

The Jemez Mountains in north-central New Mexico are volcanic in origin and have a large central caldera known as Valles Caldera. The mountains contain the Valles geothermal system, which was investigated during 1970-82 as a source of geothermal energy. This report describes the geothermal hydrology of the Jemez Mountains and presents results of an earlier 1972-75 U.S. Geological Survey study of the area in light of more recent information. Several distinct types of thermal and nonthermal ground water are recognized in the Jemez Mountains. Two types of near-surface thermal water are in the caldera: thermal meteoric water and acid sulfate water. The principal reservoir of geothermal fluids is at depth under the central and western parts of the caldera. Nonthermal ground water in Valles Caldera occurs in diverse perched aquifers and deeper valley-fill aquifers. The geothermal reservoir is recharged by meteorically derived water that moves downward from the aquifers in the caldera fill to depths of 6,500 feet or more and at temperatures reaching about 330 degrees Celsius. The heated geothermal water rises convectively to depths of 2,000 feet or less and mixes with other ground water as it flows away from the geothermal reservoir. A vapor zone containing steam, carbon dioxide, and other gases exists above parts of the liquid-dominated geothermal zone. Two subsystems are generally recognized within the larger geothermal system: the Redondo Creek subsystem and the Sulphur Creek subsystem. The permeability in the Redondo Creek subsystem is controlled by stratigraphy and fault-related structures. Most of the permeability is in the high-angle, normal faults and associated fractures that form the Redondo Creek Graben. Faults and related fractures control the flow of thermal fluids in the subsystem, which is bounded by high-angle faults. The Redondo Creek subsystem has been more extensively studied than other parts of the system. The Sulphur Springs subsystem is not as well defined. The upper vapor-dominated zone in the Sulphur Creek subsystem is separated from the liquid-dominated zone by about 800 feet of sealed caldera-fill rock. Acid springs occur at the top of the vapor zone in the Sulphur Springs area. Some more highly permeable zones within the geothermal reservoir are interconnected, but the lack of interference effects among some wells during production tests suggests effective hydraulic separation along some subsystem boundaries. Chemical and thermal evidence suggests that the Sulphur Springs subsystem may be isolated from the Redondo Creek subsystem and each may have its own zone of upflow and lateral outflow. The area of the entire geothermal reservoir is estimated to be about 12 to 15 square miles; its western limit generally is thought to be at the ring-fracture zone of the caldera. The top of the reservoir is generally considered to be the bottom of a small- permeability 'caprock' that is about 2,000 to 3,000 feet below land surface. Estimated thicknesses to the bottom of the reservoir range from 2,000 to 6,000 feet. Reservoir temperatures measured in exploration wells range from 225 degrees Celsius just below the caprock to about 330 degrees Celsius in deeper drill holes. Pressures measured in exploration wells in the Redondo Creek area ranged from 450 to 1,850 pounds per square inch. Steam-producing zones have been encountered above the liquid- dominated zones in wells, but the extent of steam zones is not well defined. The reservoir contains a near-neutral, chloride-type water containing about 7,000 milligrams per liter dissolved solids. No thermal springs in the caldera have geochemical characteristics similar to those of the geothermal reservoir fluids sampled in wells. Oxygen-18 and deuterium isotope concentrations of geothermal reservoir fluid indicate a meteoric origin. The moat valleys in

Efficacy of DL-methionine hydroxy analogue-free acid in comparison to DL-methionine in growing male white Pekin ducks.

PubMed

Kluge, H; Gessner, D K; Herzog, E; Eder, K

2016-03-01

The present study was performed to assess the bioefficacy of DL-methionine hydroxy analogue-free acid (MHA) in comparison to DL-methionine (DLM) as sources of methionine for growing male white Pekin ducks in the first 3 wk of life. For this aim, 580 1-day-old male ducks were allocated into 12 treatment groups and received a basal diet that contained 0.29% of methionine, 0.34% of cysteine and 0.63% of total sulphur containing amino acids or the same diet supplemented with either DLM or MHA in amounts to supply 0.05, 0.10, 0.15, 0.20, and 0.25% of methionine equivalents. Ducks fed the control diet without methionine supplement had the lowest final body weights, daily body weight gains and feed intake among all groups. Supplementation of methionine improved final body weights and daily body weight gains in a dose dependent-manner. There was, however, no significant effect of the source of methionine on all of the performance responses. Evaluation of the data of daily body weight gains with an exponential model of regression revealed a nearly identical efficacy (slope of the curves) of both compounds for growth (DLM = 100%, MHA = 101%). According to the exponential model of regression, 95% of the maximum values of daily body weight gain were reached at methionine supplementary levels of 0.080% and 0.079% for DLM and MHA, respectively. Overall, the present study indicates that MHA and DLM have a similar efficacy as sources of methionine for growing ducks. It is moreover shown that dietary methionine concentrations of 0.37% are required to reach 95% of the maximum of daily body weight gains in ducks during the first 3 wk of life. © 2015 Poultry Science Association Inc.

Effects of cattle-slurry treatment by acidification and separation on nitrogen dynamics and global warming potential after surface application to an acidic soil.

PubMed

Fangueiro, David; Pereira, José; Bichana, André; Surgy, Sónia; Cabral, Fernanda; Coutinho, João

2015-10-01

Cattle-slurry (liquid manure) application to soil is a common practice to provide nutrients and organic matter for crop growth but it also strongly impacts the environment. The objective of the present study was to assess the efficiency of cattle-slurry treatment by solid-liquid separation and/or acidification on nitrogen dynamics and global warming potential (GWP) following application to an acidic soil. An aerobic laboratory incubation was performed over 92 days with a Dystric Cambisol amended with raw cattle-slurry or separated liquid fraction (LF) treated or not by acidification to pH 5.5 by addition of sulphuric acid. Soil mineral N contents and NH3, N2O, CH4 and CO2 emissions were measured. Results obtained suggest that the acidification of raw cattle-slurry reduced significantly NH3 emissions (-88%) but also the GWP (-28%) while increased the N availability relative to raw cattle-slurry (15% of organic N applied mineralised against negative mineralisation in raw slurry). However, similar NH3 emissions and GWP were observed in acidified LF and non-acidified LF treatments. On the other hand, soil application of acidified cattle-slurry rather than non-acidified LF should be preferred attending the lower costs associated to acidification compared to solid-liquid separation. It can then be concluded that cattle-slurry acidification is a solution to minimise NH3 emissions from amended soil and an efficient strategy to decrease the GWP associated with slurry application to soil. Furthermore, the more intense N mineralisation observed with acidified slurry should lead to a higher amount of plant available N and consequently to higher crop yields. Copyright © 2015 Elsevier Ltd. All rights reserved.

Aluminium concentrations in Swedish forest streams and co-variations with catchment characteristics.

PubMed

Löfgren, Stefan; Cory, Neil; Zetterberg, Therese

2010-07-01

The negative effects of elevated concentrations of inorganic aluminium on aquatic organisms are well documented. Acid deposition is often cited as a main driver behind the mobilisation and speciation of aluminium in soils and surface waters. In the study, we tested the hypothesis that sulphur deposition is the main driver for elevated concentrations of inorganic aluminium in 114 base poor, boreal Swedish streams. However, the deposition of anthropogenic sulphate has decreased substantially since it peaked in the 1970s, and at the current deposition levels, we hypothesise that local site parameters play an important role in determining vulnerability to elevated concentrations of inorganic aluminium in boreal stream waters. Presented here are the results of a principal components analysis of stream water chemistry, acid deposition data and local site variables, including forest composition and stem volume. It is shown that the concentrations of both organic and inorganic aluminium are not explained by either historical or current acid deposition, but are instead explained by a combination of local site characteristics. Sites with elevated concentrations of inorganic aluminium were characterised by small catchments (<500 ha) dominated by mature stands of Norway spruce with high stem volume. Using data from the Swedish National Forest Inventory the area of productive forest land in Sweden with a higher vulnerability for elevated inorganic aluminium concentrations in forests streams is approximately 1.5 million hectares or 7% of the total productive forest area; this is higher in the south of Sweden (10%) and lower in the north (2%). A better understanding of the effects of natural processes and forest management in controlling aquatic inorganic aluminium concentrations is therefore important in future discussions about measures against surface water acidification.

Determination of beryllium concentrations in UK ambient air

NASA Astrophysics Data System (ADS)

Goddard, Sharon L.; Brown, Richard J. C.; Ghatora, Baljit K.

2016-12-01

Air quality monitoring of ambient air is essential to minimise the exposure of the general population to toxic substances such as heavy metals, and thus the health risks associated with them. In the UK, ambient air is already monitored under the UK Heavy Metals Monitoring Network for a number of heavy metals, including nickel (Ni), arsenic (As), cadmium (Cd) and lead (Pb) to ensure compliance with legislative limits. However, the UK Expert Panel on Air Quality Standards (EPAQS) has highlighted a need to limit concentrations of beryllium (Be) in air, which is not currently monitored, because of its toxicity. The aim of this work was to analyse airborne particulate matter (PM) sampled onto filter papers from the UK Heavy Metals Monitoring Network for quantitative, trace level beryllium determination and compare the results to the guideline concentration specified by EPAQS. Samples were prepared by microwave acid digestion in a matrix of 2% sulphuric acid and 14% nitric acid, verified by the use of Certified Reference Materials (CRMs). The digested samples were then analysed by Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The filters from the UK Heavy Metals Monitoring Network were tested using this procedure and the average beryllium concentration across the network for the duration of the study period was 7.87 pg m-3. The highest site average concentration was 32.0 pg m-3 at Scunthorpe Low Santon, which is significantly lower than levels that are thought to cause harm. However the highest levels were observed at sites monitoring industrial point sources, indicating that beryllium is being used and emitted, albeit at very low levels, from these point sources. Comparison with other metals concentrations and data from the UK National Atmospheric Emissions Inventory suggests that current emissions of beryllium may be significantly overestimated.

Forest biomonitoring of the largest Slovene thermal power plant with respect to reduction of air pollution.

PubMed

Al Sayegh Petkovšek, Samar

2013-02-01

The condition of the forest ecosystem in the vicinity of the largest Slovene power plant [the Šoštanj Thermal Power Plant (ŠTPP)] was monitored during the period 1991-2008 by determining the total concentration of sulphur, ascorbic acid and chlorophyll in Norway spruce needles. After 1995, the introduction of cleaning devices at the ŠTPP dramatically reduced the former extremely high SO(2) and dust emissions. The most significant findings of this comprehensive, long-duration survey are as follows: (1) the chosen parameters are suitable bioindicators of stress caused by air pollution in Norway spruce needles; they reflect both spatial and temporal variations in air pollution as well as the degree of efficiency of the cleaning devices; (2) observations show that the physiological condition of Norway spruce in northern Slovenia has significantly improved since 1995, when the first desulphurization device at ŠTPP was built, together with a reduction in the area influenced by pollution from ŠTPP; (3) metabolic processes in spruce needles react to air pollution according to the severity of the pollution and the length of exposure; exposure to high SO(2) ambient levels and/or spread over a long duration can damage the antioxidant defence mechanisms of spruce trees as well as diminishing the concentration of ascorbic acid; (4) a reduction in the exposure to air pollution improves the vitality of the trees (e.g. higher concentrations of total (a + b) chlorophyll), as well as restoring their defence capabilities as shown by higher concentrations of ascorbic acid; and (5) forest monitoring should be continued and focused on integrating the effects of multiple stressors, which can additionally affect a forest ecosystem.

[Effect of acidification on the dewaterability of sewage sludge in bioleaching].

PubMed

Zhu, Hai-Feng; Zhou, Li-Xiang; Wang, Dian-Zhan

2012-03-01

Batch experiments were performed to exploit the effect and the mechanism of bioleaching on sludge dewaterability by the inoculation of Acidithiobacillus ferrooxidans LX5 in this study. Besides, chemical leaching experiments using sulphuric acid were also performed as control to study the effect of acidification on sludge dewaterability. During the processes of both biological and chemical leaching, Zeta potential, cell lyses, morphology and structure of sludge flocs were monitored. Results showed that along with the acid production and hence the decrease of pH during bioleaching, the specific resistance of bioleached sludge decreased systematically from 1.81 x 10(12) m x kg(-1) to 0.59 x 10(12) m x kg(-1), whilst Zeta potential increased from -25.2 mV to 9.6 mV, and the natural sedimentation rate increased to as high as 48% at pH 2.90. In chemical leaching, the specific resistance decreased continuously to a minimum value of 2.6 x 10(12) m x kg(-1) at pH 3.35 and then started to increase. Zeta potential increased with the decrease of pH, and reached zero at pH 2.90. At strong acid condition, sludge cells could be decomposed, resulting in the increase of total dissolved phosphorus in centrifugal liquor of chemical leached sludge. However, this phenomenon was not observed in bioleaching process because that the phosphorus was utilized by the abundant microorganism in system. Observation by SEM showed that there was no obvious change in the flocs structure of both sludge at pH 3.35 except for that some secondary minerals appeared only in bioleached sludge. These results revealed that decrease of absolute value of Zeta potential and formation of secondary minerals caused by bioleaching were responsible for the improvement of sludge dewaterability.

Hydroxymethanesulfonic acid in size-segregated aerosol particles at nine sites in Germany

NASA Astrophysics Data System (ADS)

Scheinhardt, S.; van Pinxteren, D.; Müller, K.; Spindler, G.; Herrmann, H.

2013-12-01

In the course of two field campaigns, size-segregated particle samples were collected at nine sites in Germany, including traffic, urban, rural, marine, and mountain sites. During the chemical characterisation of the samples some of them were found to contain an unknown substance that was later on identified as hydroxymethanesulfonic acid (HMSA). HMSA is known to be formed during the reaction of S(IV) (HSO3- or SO32-) with formaldehyde in the aqueous phase. Due to its stability, HMSA may can act as a reservoir species for S(IV) in the atmosphere and is therefore of interest for the understanding of atmospheric sulphur chemistry. However, no HMSA data are available for atmospheric particles from Central Europe and even on a worldwide scale, data are scarce. Thus, the present study now provides a representative dataset with detailed information on HMSA concentrations in size-segregated Central European aerosol particles. HMSA mass concentrations in this dataset were highly variable: HMSA was found in 224 out of 738 samples (30%), sometimes in high mass concentrations exceeding those of oxalic acid. In average over all 154 impactor runs, 31.5 ng m-3 HMSA were found in PM10, contributing 0.21% to the total mass. The results show that the particle diameter, the sampling location, the sampling season and the air mass origin impact the HMSA mass concentration. Highest concentrations were found in the particle fraction 0.42-1.2 μm, at urban sites, in winter and with eastern (continental) air masses, respectively. The results suggest that HMSA is formed during aging of pollution plumes. A positive correlation of HMSA with sulphate, oxalate and PM is found (R2 > 0.4). The results furthermore suggest that the fraction of HMSA in PM slightly decreases with increasing pH.

Chemical and molecular mechanisms of antioxidants: experimental approaches and model systems

PubMed Central

Lü, Jian-Ming; Lin, Peter H; Yao, Qizhi; Chen, Changyi

2010-01-01

Abstract Free radicals derived from oxygen, nitrogen and sulphur molecules in the biological system are highly active to react with other molecules due to their unpaired electrons. These radicals are important part of groups of molecules called reactive oxygen/nitrogen species (ROS/RNS), which are produced during cellular metabolism and functional activities and have important roles in cell signalling, apoptosis, gene expression and ion transportation. However, excessive ROS attack bases in nucleic acids, amino acid side chains in proteins and double bonds in unsaturated fatty acids, and cause oxidative stress, which can damage DNA, RNA, proteins and lipids resulting in an increased risk for cardiovascular disease, cancer, autism and other diseases. Intracellular antioxidant enzymes and intake of dietary antioxidants may help to maintain an adequate antioxidant status in the body. In the past decades, new molecular techniques, cell cultures and animal models have been established to study the effects and mechanisms of antioxidants on ROS. The chemical and molecular approaches have been used to study the mechanism and kinetics of antioxidants and to identify new potent antioxidants. Antioxidants can decrease the oxidative damage directly via reacting with free radicals or indirectly by inhibiting the activity or expression of free radical generating enzymes or enhancing the activity or expression of intracellular antioxidant enzymes. The new chemical and cell-free biological system has been applied in dissecting the molecular action of antioxidants. This review focuses on the research approaches that have been used to study oxidative stress and antioxidants in lipid peroxidation, DNA damage, protein modification as well as enzyme activity, with emphasis on the chemical and cell-free biological system. PMID:19754673

Co-Liquefaction of Elbistan Lignite with Manure Biomass; Part 1. Effect of Catalyst Concentration

NASA Astrophysics Data System (ADS)

Koyunoglu, Cemil; Karaca, Hüseyin

2017-12-01

The hydrogenation of coal by molecular hydrogen has not been appreciable unless a catalyst has been used, especially at temperatures below 500 °C. Conversion under these conditions is essentially the result of the pyrolysis of coal, although hydrogen increases the yield of conversion due to the stabilization of radicals and other reactive species. Curtis and his co-workers has shown that highly effective and accessible catalyst are required to achieve high levels of oil production from the coprocessing of coal and heavy residua. In their work, powdered hydrotreating catalyst at high loadings an oil-soluble metal salts of organic acids as catalyst precursors achieved the highest levels of activity for coal conversion and oil production. Red mud which is iron-based catalysed has been used in several co-processing studies. It was used as an inexpensive sulphur sink for the H2S evolved to convert Fe into pyrrohotite during coal liquefaction. In this study, Elbistan Lignite (EL) processed with manure using red mud as a catalyst with the range of concentration from 3% to 12%. The main point of using red mud catalyst is to enhance oil products yield of coal liquefaction, which deals with its catalytic activity. On the other hand, red mud acts on EL liquefaction with manure as a catalyst and represents an environmental option to produce lower sulphur content oil products as well.

A ubiquitous thermoacidophilic archaeon from deep-sea hydrothermal vents

USGS Publications Warehouse

Reysenbach, A.-L.; Liu, Yajing; Banta, A.B.; Beveridge, T.J.; Kirshtein, J.D.; Schouten, S.; Tivey, M.K.; Von Damm, Karen L.; Voytek, M.A.

2006-01-01

Deep-sea hydrothermal vents are important in global biogeochemical cycles, providing biological oases at the sea floor that are supported by the thermal and chemical flux from the Earth's interior. As hot, acidic and reduced hydrothermal fluids mix with cold, alkaline and oxygenated sea water, minerals precipitate to form porous sulphide-sulphate deposits. These structures provide microhabitats for a diversity of prokaryotes that exploit the geochemical and physical gradients in this dynamic ecosystem. It has been proposed that fluid pH in the actively venting sulphide structures is generally low (pH < 4.5), yet no extreme thermoacidophile has been isolated from vent deposits. Culture-independent surveys based on ribosomal RNA genes from deep-sea hydrothermal deposits have identified a widespread euryarchaeotal lineage, DHVE2 (deep-sea hydrothermal vent euryarchaeotic 2). Despite the ubiquity and apparent deep-sea endemism of DHVE2, cultivation of this group has been unsuccessful and thus its metabolism remains a mystery. Here we report the isolation and cultivation of a member of the DHVE2 group, which is an obligate thermoacidophilic sulphur- or iron-reducing heterotroph capable of growing from pH 3.3 to 5.8 and between 55 and 75??C. In addition, we demonstrate that this isolate constitutes up to 15% of the archaeal population, providing evidence that thermoacidophiles may be key players in the sulphur and iron cycling at deep-sea vents. ?? 2006 Nature Publishing Group.

Mineral status in canine medial coronoid process disease: a cohort study using analysis of hair by mass spectrometry.

PubMed

Davies, M; West, J; Williams, C; Gardner, D S

2017-05-06

In several species, developmental skeletal diseases involving abnormal endochondral ossification have been associated with imbalanced mineral intake. Hair analysis reflects long-term mineral status. To determine the mineral content of hair from dogs with or without medial coronoid process disease (MCPD). Dogs with MCPD have a different profile of minerals known to influence metalloenzymes involved in endochondral ossification. After cleansing, chelation and acid digestion of hair samples (n=79 in total: control dogs, n=70 v MCPD, n=9), mineral profile (7 major and 25 trace elements) was determined by inductively coupled plasma-mass spectrometry. Dogs were of similar age (control, 4.05 [1.85-7.70] v MCPD, 4.30 [3.25-6.53] median (IQR) years; P=0.78) and gender (control, n=43/27 v MCPD, n=4/5 males/females). 28/70 (40 per cent) of control and 8/9 (88 per cent) of MCPD dogs were neutered, respectively. Hair from dogs with MCPD contained significantly lower amounts (µg/g/DM) of copper, sulphur and zinc (all at P<0.001). Age, sex and neutered status had no effect on hair mineral status. Based on hair analysis, a role for mineral imbalance including copper, sulphur and zinc in the aetiopathogenesis of canine MCPD is suggested. Hair mineral analysis may prove useful as a biomarker for susceptible puppies. British Veterinary Association.

Synthesis of goethite in solutions of artificial seawater and amino acids: a prebiotic chemistry study

NASA Astrophysics Data System (ADS)

Carneiro, Cristine E. A.; Ivashita, Flávio F.; de Souza, Ivan Granemann; de Souza, Cláudio M. D.; Paesano, Andrea; da Costa, Antonio C. S.; di Mauro, Eduardo; de Santana, Henrique; Zaia, Cássia T. B. V.; Zaia, Dimas A. M.

2013-04-01

This study investigated the synthesis of goethite under conditions resembling those of the prebiotic Earth. The artificial seawater used contains all the major elements as well as amino acids (α-Ala, β-Ala, Gly, Cys, AIB) that could be found on the prebiotic Earth. The spectroscopic methods (FT-IR, EPR, Raman), scanning electron microscopy (SEM) and X-ray diffraction showed that in any condition Gly and Cys favoured the formation of goethite, artificial seawater plus β-Ala and distilled water plus AIB favoured the formation of hematite and for the other synthesis a mixture of goethite and hematite were obtained. Thus in general no protein amino acids (β-Ala, AIB) favoured the formation of hematite. As shown by surface enhanced Raman spectroscopy (SERS) spectra the interaction between Cys and Fe3+ of goethite is very complex, involving decomposition of Cys producing sulphur, as well as interaction of carboxylic group with Fe3+. SERS spectra also showed that amino/CN and C-CH3 groups of α-Ala are interacting with Fe3+ of goethite. For the other samples the shifting of several bands was observed. However, it was not possible to say which amino acid groups are interacting with Fe3+. The pH at point of zero charge of goethites increased with artificial seawater and decreased with amino acids. SEM images showed when only goethite was synthesized the images of the samples were acicular and when only hematite was synthesized the images of the samples were spherical. SEM images for the synthesis of goethite with Cys were spherical crystal aggregates with radiating acicular crystals. The highest resonance line intensities were obtained for the samples where only hematite was obtained. Electron paramagnetic resonance (EPR) and Mössbauer spectra showed for the synthesis of goethite with artificial seawater an isomorphic substitution of iron by seawater cations. Mössbauer spectra also showed that for the synthesis goethite in distilled water plus Gly only goethite was synthesized and in artificial seawater plus Cys a doublet due to interaction of iron with artificial seawater/Cys was observed. It should be pointed out that EPR spectroscopy did not show the interaction of iron with artificial seawater/Cys.

Synthesis and characterization of sulfonated poly ether ether ketone (sPEEK) membranes for low temperature fuel cells

NASA Astrophysics Data System (ADS)

Ali, Mawlood Maajal; Rizvi, S. J. A.; Azam, Ameer

2018-05-01

Poly ether ether ketone (PEEK) was sulfonated with 1.0 M sulphuric acid for varying durations to have various degrees of sulfonation (DS) from 43 to 55%. The FT-IR spectra confirmed the successful sulfonation of PEEK. The sulfonated PEEK (sPEEK) membranes were prepared by a solvent casting method using dimethylacetamide (DMAc) as solvent and upon drying the membranes were characterized. The DS% and ion exchange capacity (IEC) were determined by a back titration method. The IEC and DS of sPEEK was found to increase with the increment of sulfonation reaction time. Water uptake also increased with increase in the DS. The Thermogravimetric (TGA) curves revealed poor thermal stability of sPEEK. The proton conductivity of sPEEK membrane was found to considerably better with degree of sulfonation for fuel cell application.

Chemical burns as assault injuries in Jamaica.

PubMed

Branday, J; Arscott, G D; Smoot, E C; Williams, G D; Fletcher, P R

1996-03-01

A three-fold greater incidence of chemical burn injuries in Jamaican hospitals, compared to burn centres in other industrial countries, underscores the problem of the use of common chemicals for assault weapons in this country. With the increased availability of guns for personal use, many Jamaicans learned the value of carrying household chemicals such as sulphuric acid from batteries or sodium hydroxide obtained from cleaning supplies. Chemicals carried in a container, such as one might carry mace, afforded a means of defence among the lower socioeconomic groups who could not afford handguns. This use of dangerous chemicals for defensive weapons has extended to the use of chemicals for assault. The pattern of chemical injury differs significantly from most reports in the literature in both prevalence and aetiology. This review was prepared to examine these injuries with a view to planning strategies for prevention.

A method for the determination of vanadium and iron oxidation states in naturally occurring oxides and silicates

USGS Publications Warehouse

Wanty, R.B.; Goldhaber, M.B.

1985-01-01

A valence-specific analytical method for determining V3+ in ore minerals has been developed that involves two steps: dissolution of a mineral sample without disturbing the V3+/Vtot ratio, followed by determination of V3+ in the presence of V4+. The samples are dissolved in a mixture of hydrofluoric and sulphuric acids at 100?? in Teflon-lined reaction vessels. Tervalent vanadium is then determined colorimetrically by formation of a V3+-thiocyanate complex in aqueous-acetone medium. Fe3+ is measured semi-quantitatively in the same solution. The method has been tested with two naturally occurring samples containing vanadium and iron. The results obtained were supported by those obtained by other methods, including electron spin resonance spectroscopy, thermogravimetric analysis, and Mo??ssbauer spectroscopy. ?? 1985.

Experimental study and modelling of water sorption/desorption isotherms on two agricultural products: Apple and carrot

NASA Astrophysics Data System (ADS)

Timoumi, S.; Zagrouba, F.; Mihoubi, D.; Tlili, M. M.

2004-12-01

This work is focused on some properties of dried apple (Red Chief) and carrot (Misky). Water sorption isotherms of carrot and apple were investigated at three temperatures: 30, 40 and 60°C, corresponding to drying temperatures, by the static method consisting of the use of different sulphuric acid solutions. Guggenheim-Anderson-de Boer (G.A.B) model is found to describe the experimental curves better than Henderson, Hasley and Oswin models with a correlation coefficient superior to 0.97 for both products. The hysteresis phenomenon was clearly observed in the case of apple isotherms. The experimental data were also used to determine the isosteric enthalpy of desorption of apple and carrot. The isosteric enthalpy of desorption decreased with increase in moisture content and the trend became asymptotic.

Complexation of nitrogen and sulphur donor Schiff's base ligand to Cr(III) and Ni(II) metal ions: Synthesis, spectroscopic and antipathogenic studies

NASA Astrophysics Data System (ADS)

Sharma, Amit Kumar; Chandra, Sulekh

2011-01-01

2,6-Diacetyl pyridine based ligand was synthesized by the reaction of 2,6-diacetyl pyridine with thiocarbohydrazide in presence of acetic acid. The coordination compounds with Cr(III) and Ni(II) metal ions having [Cr(L)X]X 2 and [Ni(L)X]X compositions (where L = ligand and X = NO 3-, Cl - and CH 3COO -) were synthesized and characterized by physicochemical and spectral studies. The studies like elemental analyses, molar conductance measurements, magnetic susceptibility measurements, IR, UV-Vis, NMR, mass and EPR reveal that the complexes are octahedral. The compounds were examined against the pathogenic fungal and bacterial strains like Alternaria brassicae, Aspergillus niger, Fusarium oxysporum, Xanthomonas compestris and Pseudomonas aeruginosa. A. niger causes the diseases Apergillosis and Otomycosis in humans.

Purification and physicochemical properties of superoxide dismutase from two photosynthetic microorganisms.

PubMed

Lumsden, J; Cammack, R; Hall, D O

1976-07-08

Superoxide dismutase (EC 1.15.1.1) has been isolated and characterised from the blue-green alga Spirulina platensis and from aerobically-grown Rhodopseudomonas spheroides, a purple, non-sulphur bacterium. The former enzyme contains 1 gatom of iron and the latter 1 gatom of manganese per mol; both enzymes have a molecular weight of 37 000-38 000, being composed of two non-covalently joined subunits of equal size. Various spectral studies have been carried out including absorbance, circular dichroism and electron spin resonance. Catalytic activity has been studied as a function of pH and shows a decrease at alkaline pH values. The manganoenzyme is generally more stable to various potentially denaturing conditions and is resistant to inactivation by hydrogen peroxide. Amino acid compositions and N-terminal residue determinations are presented.

Chemical Imaging and Stable Isotope Analysis of Atmospheric Particles by NanoSIMS (Invited)

NASA Astrophysics Data System (ADS)

Sinha, B.; Harris, E. J.; Pöhlker, C.; Wiedemann, K. T.; van Pinxteren, D.; Tilgner, A.; Fomba, K. W.; Schneider, J.; Roth, A.; Gnauk, T.; Fahlbusch, B.; Mertes, S.; Lee, T.; Collett, J. L.; Shiraiwa, M.; Gunthe, S. S.; Smith, M.; Artaxo, P. P.; Gilles, M.; Kilcoyne, A. L.; Moffet, R.; Weigand, M.; Martin, S. T.; Poeschl, U.; Andreae, M. O.; Hoppe, P.; Herrmann, H.; Borrmann, S.

2013-12-01

Chemical imaging analysis of the internal distribution of chemical compounds by a combination of SEM-EDX, and NanoSIMS allows investigating the physico-chemical properties and isotopic composition of individual aerosol particles. Stable sulphur isotope analysis provides insight into the sources, sinks and oxidation pathways of SO2 in the environment. Oxidation by OH radicals, O3 and H2O2 enriches the heavier isotope in the product sulphate, whereas oxidation by transition metal ions (TMI), hypohalites and hypohalous acids depletes the heavier isotope in the product sulphate. The isotope fractionation during SO2 oxidation by stabilized Criegee Intermediate radicals is unknown. We studied the relationship between aerosol chemical composition and predominant sulphate formation pathways in continental clouds in Central Europe and during the wet season in the Amazon rain forest. Sulphate formation in continental clouds in Central Europe was studied during HCCT-2010, a lagrangian-type field experiment, during which an orographic cloud was used as a natural flow-through reactor to study in-cloud aerosol processing (Harris et al. 2013). Sulphur isotopic compositions in SO2 and H2SO4 gas and particulate sulphate were measured and changes in the sulphur isotope composition of SO2 between the upwind and downwind measurement sites were used to determine the dominant SO2 chemical removal process occurring in the cloud. Changes in the isotopic composition of particulate sulphate revealed that transition metal catalysis pathway was the dominant SO2 oxidation pathway. This reaction occurred primarily on coarse mineral dust particles. Thus, sulphate produced due to in-cloud SO2 oxidation is removed relatively quickly from the atmosphere and has a minor climatic effect. The aerosol samples from the Amazonian rainforest, a pristine tropical environment, were collected during the rainy season. The samples were found to be dominated by SOA particles in the fine mode and primary biological aerosol particles in the coarse mode (Pöhlker et al. 2012). We applied STXM-NEXAFS analysis, SEM-EDX analysis and NanoSIMS analysis to investigate the morphology, chemical composition and isotopic composition of aerosol samples. Biogenic salt particles emitted from active biota in the rainforest were found to be enriched in the heavier sulphur isotope, whereas particles with a high organic mass fraction modified by condensation of VOC oxidation products and/or cloud processing were significantly depleted in the heavier sulphur isotope compared to the seed particles. This indicates either a depleted gas phase source of sulphur dioxide contributed to the sulphate formation via the H2O2, O3 or OH oxidation pathway or an unaccounted reaction pathway which depletes the heavier isotope in the product sulphate contributes to the secondary sulphate formation in the pristine Amazon rainforest. Harris, E., et al., Science 340, 727-730, 2013 Pöhlker, C., Science 337, 1075-1078, 2012

Chinese mitten crab (Eriocheir sinensis) iron-sulphur cluster assembly protein 2 (EsIscA2) is differentially regulated after immune and oxidative stress challenges.

PubMed

Zhang, Peng; Liu, Yu; Wang, Min; Dong, Miren; Liu, Zhaoqun; Jia, Zhihao; Wang, Weilin; Zhang, Anguo; Wang, Lingling; Song, Linsheng

2018-07-01

Iron-sulphur clusters (ISCs), one of the oldest and most versatile cofactors of proteins, are involved in catalysis reactions, electron transport reactions, regulation processes as well as sensing of ambient conditions. Iron-sulphur cluster assembly protein (IscA) is a scaffold protein member of ISC formation system, which plays a significant role in the assembly and maturation process of ISC proteins. In the present study, the cDNA sequence of iron-sulphur cluster assembly protein 2 (designated as EsIscA2) was cloned from Eriocheir sinensis. The open reading frame (ORF) of EsIscA2 was of 507 bp, encoding a peptide of 168 amino acids with a typically conserved Fe-S domain. A tetrameric form was predicated by the SWISS-MODEL prediction algorithm, and three conserved cysteine residues (Cys-93, Cys-158, Cys-160) from each IscA monomer were predicted to form a 'cysteine pocket'. The deduced amino acid sequence of EsIscA2 shared over 50% similarity with that of other IscAs. EsIscA2 was clustered with IscA2 proteins from invertebrates and vertebrates, indicating that the protein was highly conservative in the evolution. rEsIscA2 exhibited a high iron binding affinity in the concentration ranging from 2 to 200 μM. EsIscA2 transcripts were detected in all the tested tissues including gonad, hemocytes, gill, muscle, heart, hepatopancreas and eyestalk, and EsIscA2 protein was detected in the mitochondria of hemocytes. The highest mRNA expression level of EsIscA2 was detected in muscle and hepatopancreas, which was about 34.66-fold (p < 0.05) and 27.07-fold (p < 0.05) of that in hemocytes, respectively. After Aeromonas hydrophila and lipopolysaccharide (LPS) stimulations, the mRNA expression of EsIscA2 in hemocytes was down-regulated and reached the lowest level at 24 h (0.31-fold, p < 0.05) and 48 h (0.29-fold, p < 0.05) compared to control group, respectively. And the expression of EsIscA2 mRNA in hepatopancreas was repressed from 6 h to 48 h post stimulation (p < 0.05). When the primary cultured crab hemocytes were incubated with different concentrations of H 2 O 2 for 15 min, the expression level of EsIscA2 mRNA was significantly repressed to the 0.34-0.44-fold of that in the control group. After A. hydrophila stimulation, the mRNA expression of EsGrx2 was up-regulated at 3 h (3.22-fold compared to control group, p < 0.05) and reached the peak at 12 h (4.88-fold, p < 0.05). All these results suggested that EsIscA2 had iron-binding capabilities as observed in IscA proteins from other organisms, supporting the role of EsIscA2 as a mitochondrial iron donor for ISC synthesis in Chinese mitten crab. Its differential mRNA expression after immune and oxidative stress challenges suggested the adaptations of ISC synthesis rates to these stress conditions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Mass-dependent and Mass-independent Sulphur Isotope Fractionation Accompanying Thermal- and Photo-chemical Decomposition of Sulphur Bearing Organic Compounds

NASA Astrophysics Data System (ADS)

Oduro, Harry; Izon, Gareth; Ono, Shuhei

2014-05-01

The bimodal S-isotope record, specifically the transition from mass independent (MIF) to mass dependent fractionation (MDF), is perhaps the most widely cited line of evidence for an irreversible rise in atmospheric oxygen at ca. 2.4Ga. The production and preservation of S-MIF, manifested in both Δ33S and Δ36S, within the geological record are linked to atmospheric O2 via a number of arguments. However, to date, the only mechanism capable of generating S-MIF consistent with the Archaean sedimentary records involves gas-phase ultraviolet irradiation of SO21 photolysis. More recently, Δ33S S-MIF trends have been reported from en vitro thermochemical sulphate reduction (TSR) experiments, prompting authors to question the importance of S-MIF as a proxy for Earth oxidation2. Importantly, whilst emerging TSR experiments3,4 affirm the reported Δ33S trends2, these experiments fail to identify correlated S-MIF between Δ33S and Δ36S values3,4. Realization that S-MIF is confined to Δ33S during TSR, precludes TSR as a mechanism responsible for the origin of the Archaean S-MIF record but strongly suggests the effect originating from a magnetic isotope effect (MIE) associated with 33S nucleus3,4. Clearly, photochemical and thermochemical processes impart different Δ36S/Δ33S trends with significant variation in δ34S; however, a complete experimental elucidation of mechanisms responsible for the S-MIF and S-MIE signatures is lacking. Interestingly, a complete understanding of the S-isotope chemistry during thermal- and photo-chemical decomposition may reveal wavelength and thermal dependence archived in the sedimentary record. Here we extend the experimental database to explore the magnitude and sign of Δ36S/Δ33S and δ34S produced during both photo- and thermochemical processes. Here the organic sulphur compounds (OSC) utilized in these experiments carries diagnostic Δ36S/Δ33S patterns that differ from those reported from photolysis experiment SO2 and from the Archaean sedimentary record. Further thermal decomposition of several sulphur containing compounds with; 1) an aliphatic-S (e.g., diphenyl disulphide), 2) tri-substituted aromatic-S (trithiane), and S-amino acids (e.g., cysteine, methionine, taurine, and glutathionine) were tested for four S-isotope fractionation under vacuum. Among these, aromatic trithiane produced anomalous 33S up to 1.3‰, indicating thermal decomposition through radical chemistry, producing S-MIE. While taurine with sulphonic acid (R-SO2OH) functional groups yielded S-MDF up to 15‰ (between the AVS and the residual OSC), which is consistent with estimated zero-point energy shifts for thiol (R-SH), and thiyl (R-S-CH3) groups of cysteine and methionine, respectively. These results suggest that OSC might undergo either thermal or photochemical decomposition and the S-MIF, S-MDF, and S-MIE signatures may be archived in the geologic record. The emerging mechanisms responsible for these isotope signals and their implications will be discussed in more detail. Ultimately this work offers a framework where these signals can be used as a diagnostic marker to distinguish between thermo- and photochemical processes. References: 1. Farquhar et al., Science 2000 2. Watanabe et al., Science 2010; 3. Oduro et al., PNAS 2011; 4. Kopf and Ono, GCA 2012.

Quantifying Sulphur Emissions and Atmospheric Aerosol Loading From the 1730-36 Lanzarote Eruption

NASA Astrophysics Data System (ADS)

Sharma, K.; Blake, S.; Self, S.

2005-12-01

The AD 1730-36 eruption of Lanzarote (Canary Islands) is the third largest basaltic fissure eruption known to have occurred in the last 1000 years, after the Icelandic events of Laki (AD 1783-84) and Eldgja (AD 934). Our new volume estimates suggest that the Lanzarote eruption produced ~6 km3 of alkali basalt magma along a 15-km long, E-W trending fissure. Eruptive activity occurred in five distinct phases. Each phase began with Strombolian fire fountain activity, building large spatter and scoria cones. This was accompanied and followed by effusive aa and pahoehoe lava flow emplacement. As studies in Iceland have shown, this type of sustained fissure eruption can release large amounts of SO2 to the upper atmosphere, leading to the formation of sulphate aerosol clouds and causing widespread environmental damage and human suffering. Matrix glasses in scoria and surface lava samples have 80-300 ppm S (EMPA) and 300-600 ppm H2O (FTIR), whereas glass inclusions in olivine have 420-2650 ppm S and 1000-5000 ppm H2O. Low sulphur inclusions are believed to be partially degassed, representing melt that was trapped during degassing-induced crystallization that occurred as a result of shallow decompression. The inclusions with the highest sulphur contents trap the original un-degassed melt, as indicated by their consistent S/K2O ratio (0.22). The high sulphur contents are also consistent with our finding, from olivine-spinel equilibria, that the magma was relatively oxidized (log fO2 -4.8) therefore favouring the formation of sulphate species and preventing sulphide saturation. Our glass analyses indicate that 40 Mt of SO2 was injected into the upper troposphere - lower stratosphere via 12-16-km-high eruption plumes and that over half this amount was released during the first year of activity. This figure correlates with published Greenland ice-core (GISP-2) data that shows an acidity spike in 1731, suggesting stratospheric transport of sulphate aerosol to the North during the first year of eruption. Historical records note the presence of a dry fog over much of Europe during 1733. This, together with proxy climate indicators such as a marked tree ring anomaly in 1732 and a known decrease in the Northern hemisphere surface temperatures suggests that the Lanzarote eruption had some impact on Northern Hemisphere climate in the years following the activity.

An overview of geoengineering of climate using stratospheric sulphate aerosols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rasch, Philip J.; Tilmes, S.; Turco, Richard P.

2010-01-01

We provide an overview of geoengineering by stratospheric sulphate aerosols. The state of understanding about this topic as of early 2008 is reviewed, summarizing the past 30 years of work in the area, highlighting some very recent studies using climate models, and discussing methods used to deliver sulphur species to the stratosphere. The studies reviewed here suggest that sulphate aerosols can counteract the globally averaged temperature increase associated with increasing greenhouse gases, and reduce changes to some other components of the Earth system. There are likely to be remaining regional climate changes after geoengineering, with some regions experiencing significant changesmore » in temperature or precipitation. The aerosols also serve as surfaces for heterogeneous chemistry resulting in increased ozone depletion. The delivery of sulphur species to the stratosphere in a way that will produce particles of the right size is shown to be a complex and potentially very difficult task. Two simple delivery scenarios are explored, but similar exercises will be needed for other suggested delivery mechanisms. While the introduction of the geoengineering source of sulphate aerosol will perturb the sulphur cycle of the stratosphere signicantly, it is a small perturbation to the total (stratosphere and troposphere) sulphur cycle. The geoengineering source would thus be a small contributor to the total global source of ‘acid rain’ that could be compensated for through improved pollution control of anthropogenic tropospheric sources. Some areas of research remain unexplored. Although ozone may be depleted, with a consequent increase to solar ultraviolet-B (UVB) energy reaching the surface and a potential impact on health and biological populations, the aerosols will also scatter and attenuate this part of the energy spectrum, and this may compensate the UVB enhancement associated with ozone depletion. The aerosol will also change the ratio of diffuse to direct energy reaching the surface, and this may influence ecosystems. The impact of geoengineering on these components of the Earth system has not yet been studied. Representations for the formation, evolution and removal of aerosol and distribution of particle size are still very crude, and more work will be needed to gain confidence in our understanding of the deliberate production of this class of aerosols and their role in the climate system.« less

An overview of geoengineering of climate using stratospheric sulphate aerosols.

PubMed

Rasch, Philip J; Tilmes, Simone; Turco, Richard P; Robock, Alan; Oman, Luke; Chen, Chih-Chieh; Stenchikov, Georgiy L; Garcia, Rolando R

2008-11-13

We provide an overview of geoengineering by stratospheric sulphate aerosols. The state of understanding about this topic as of early 2008 is reviewed, summarizing the past 30 years of work in the area, highlighting some very recent studies using climate models, and discussing methods used to deliver sulphur species to the stratosphere. The studies reviewed here suggest that sulphate aerosols can counteract the globally averaged temperature increase associated with increasing greenhouse gases, and reduce changes to some other components of the Earth system. There are likely to be remaining regional climate changes after geoengineering, with some regions experiencing significant changes in temperature or precipitation. The aerosols also serve as surfaces for heterogeneous chemistry resulting in increased ozone depletion. The delivery of sulphur species to the stratosphere in a way that will produce particles of the right size is shown to be a complex and potentially very difficult task. Two simple delivery scenarios are explored, but similar exercises will be needed for other suggested delivery mechanisms. While the introduction of the geoengineering source of sulphate aerosol will perturb the sulphur cycle of the stratosphere signicantly, it is a small perturbation to the total (stratosphere and troposphere) sulphur cycle. The geoengineering source would thus be a small contributor to the total global source of 'acid rain' that could be compensated for through improved pollution control of anthropogenic tropospheric sources. Some areas of research remain unexplored. Although ozone may be depleted, with a consequent increase to solar ultraviolet-B (UVB) energy reaching the surface and a potential impact on health and biological populations, the aerosols will also scatter and attenuate this part of the energy spectrum, and this may compensate the UVB enhancement associated with ozone depletion. The aerosol will also change the ratio of diffuse to direct energy reaching the surface, and this may influence ecosystems. The impact of geoengineering on these components of the Earth system has not yet been studied. Representations for the formation, evolution and removal of aerosol and distribution of particle size are still very crude, and more work will be needed to gain confidence in our understanding of the deliberate production of this class of aerosols and their role in the climate system.

Cryosols Formation and classification in the semiarid Antarctica: the Weddel Sea sector of northern Seymour Island

NASA Astrophysics Data System (ADS)

Gjorup, Davi; Schaefer, Carlos; Francelino, Marcio

2015-04-01

The Seymour Island is located in the northern sector of the Weddell Sea zone, at the Antarctic Peninsular area, representing a transitional zone between Maritime and Continental Antarctica, with a subpolar, semiarid climate. The Seymour Island is predominantly composed by marine sedimentary rocks of Cretaceus to Eocene age. The aims of this work were to study the chemical, physical, mineralogical and morphological attributes of a selected, representative toposequence of soils at the northern sector of Seymour Island. Soil formation processes and taxonomical implications were discussed. Nine soil profiles were described, collected and analysed, following a toposequence according to different parent materials and landforms. Samples were subjected to textural analysis, routine chemical analysis, chemical extractions by ammonium oxalate and CBD, as well as X ray diffraction. Permafrost is continuous and widespread, generally at depths of less than 100 cm, so the Gelisols order (Soil Taxonomy), or Cryosols (WRB), are the dominant soils. Cryoturbation and organic matter accumulation were not observed. Soils were separated into two groups: acid-sulphate soils and alkaline soils, unaffected by sulphates. The first are the best developed in the study area, meaning a significant physico-chemical and mineralogical alteration. Low pH and high Al saturation and potential acidity are typical. This accounts for primary mineral dissolution, and its absence in the clay fraction. Secondary minerals are those related to sulphide oxidation: soluble and insoluble sulphates, low crystalline Fe-hydroxides and little crystalline Fe phases. The peculiar yellowish colour of these soils are attributed to the presence of Fe-oxides and Jarosite. The presence of 2:1 clays (smectite and illite) in the Clay fraction despite the acidity is due to low leaching. The alkaline soils, non affected by sulphates do not showed any marked weathering or transformation, with high pH, low potential acidity and zero Al saturation. The main process is cryoclastic and haloclastic weathering. Primary minerals are present even in the clay fraction, corroborating its low weathering degree and chemical alteration. The landform is determinant for the chemical status of theses soils, by favoring or reducing leaching. Sulphurization and halomorphism are the dominant soil-forming processes in Seymour Island.

Mung bean proteins and peptides: nutritional, functional and bioactive properties.

PubMed

Yi-Shen, Zhu; Shuai, Sun; FitzGerald, Richard

2018-01-01

To date, no extensive literature review exists regarding potential uses of mung bean proteins and peptides. As mung bean has long been widely used as a food source, early studies evaluated mung bean nutritional value against the Food and Agriculture Organization of the United Nations (FAO)/the World Health Organization (WHO) amino acids dietary recommendations. The comparison demonstrated mung bean to be a good protein source, except for deficiencies in sulphur-containing amino acids, methionine and cysteine. Methionine and cysteine residues have been introduced into the 8S globulin through protein engineering technology. Subsequently, purified mung bean proteins and peptides have facilitated the study of their structural and functional properties. Two main types of extraction methods have been reported for isolation of proteins and peptides from mung bean flours, permitting sequencing of major proteins present in mung bean, including albumins and globulins (notably 8S globulin). However, the sequence for albumin deposited in the UniProt database differs from other sequences reported in the literature. Meanwhile, a limited number of reports have revealed other useful bioactivities for proteins and hydrolysed peptides, including angiotensin-converting enzyme inhibitory activity, anti-fungal activity and trypsin inhibitory activity. Consequently, several mung bean hydrolysed peptides have served as effective food additives to prevent proteolysis during storage. Ultimately, further research will reveal other nutritional, functional and bioactive properties of mung bean for uses in diverse applications.

Process for cobalt separation and recovery in the presence of nickel from sulphate solutions by Cyanex 272

NASA Astrophysics Data System (ADS)

Park, Kyung-Ho; Mohapatra, Debasish

2006-10-01

The present paper deals with the extraction of cobalt from a solution containing cobalt and nickel in a sulphate medium similar to the leach liquor obtained by the dilute sulphuric acid pressure leaching of the Pacific Ocean nodules matte followed by copper extraction. The commercial extractant Cyanex 272 (bis (2, 4, 4-trimethylpentyl) phosphinic acid) is used for this purpose. The leach liquor used for the present study contains Co =1.78 g/L and Ni=16.78 g/L. Before cobalt extraction, impurities, such as copper and iron, are removed from the leach liquor by the precipitation method. Increasing the concentration of Cyanex 272 increased the extraction percentage of cobalt due to the increase of equilibrium pH. Cobalt extraction efficiency of >99.9 % is achieved with 0.20 M Cyanex 272 in two counter-current stages at an aqueous: organic (A:O) phase ratio of 1.5∶1. Complete stripping of cobalt from the loaded organic containing 2.73 g/L Co was carried out at pH 1.4 by a synthetic cobalt spent electrolyte in two stages at an A:O ratio of 1∶2. The enrichment of cobalt during extraction and stripping operations was about 3.5 times. A complete process flowsheet for the separation and recovery of cobalt is presented.

Mitigating secondary aerosol generation potentials from biofuel use in the energy sector.

PubMed

Tiwary, Abhishek; Colls, Jeremy

2010-01-01

This paper demonstrates secondary aerosol generation potential of biofuel use in the energy sector from the photochemical interactions of precursor gases on a life cycle basis. The paper is divided into two parts-first, employing life cycle analysis (LCA) to evaluate the extent of the problem for a typical biofuel based electricity production system using five baseline scenarios; second, proposing adequate mitigation options to minimise the secondary aerosol generation potential on a life cycle basis. The baseline scenarios cover representative technologies for 2010 utilising energy crop (miscanthus), short rotation coppiced chips and residual/waste wood in different proportions. The proposed mitigation options include three approaches-biomass gasification prior to combustion, delaying the harvest of biomass, and increasing the geographical distance between the biomass plant and the harvest site (by importing the biofuels). Preliminary results indicate that the baseline scenarios (assuming all the biomass is sourced locally) bear significant secondary aerosol formation potential on a life cycle basis from photochemical neutralisation of acidic emissions (hydrogen chloride and sulphur dioxide) with ammonia. Our results suggest that gasification of miscanthus biomass would provide the best option by minimising the acidic emissions from the combustion plant whereas the other two options of delaying the harvest or importing biofuels from elsewhere would only lead to marginal reduction in the life cycle aerosol loadings of the systems.

Hydrometallurgical recycling of lithium-ion batteries by reductive leaching with sodium metabisulphite.

PubMed

Vieceli, Nathália; Nogueira, Carlos A; Guimarães, Carlos; Pereira, Manuel F C; Durão, Fernando O; Margarido, Fernanda

2018-01-01

The hydrometallurgical extraction of metals from spent lithium-ion batteries (LIBs) was investigated. LIBs were first dismantled and a fraction rich in the active material was obtained by physical separation, containing 95% of the initial electrode, 2% of the initial steel and 22% of plastic materials. Several reducers were tested to improve metals dissolution in the leaching step using sulphuric acid. Sodium metabisulphite led to the best results and was studied in more detail. The best concentration of Na 2 S 2 O 5 was 0.1 M. The metals dissolution increased with acid concentration, however, concentrations higher than 1.25 M are unnecessary. Best results were reached using a stirring speed of 400 min -1 . The metals leaching efficiency from the active material (Li, Mn, Ni, Co) increased with the temperature and was above 80% for temperatures higher than 60 °C. The dissolution of metals also rose with the increase in the liquid/solid ratio (L/S), however, extractions above 85% can be reached at L/S as lower as 4.5 L/kg, which is favourable for further purification and recovery operations. About 90% of metals extraction can be achieved after only 0.5 h of leaching. Sodium metabisulphite can be an alternative reducer to increase the leaching of Li, Mn, Co, and Ni from spent LIBs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mung bean proteins and peptides: nutritional, functional and bioactive properties

PubMed Central

Yi-Shen, Zhu; Shuai, Sun; FitzGerald, Richard

2018-01-01

To date, no extensive literature review exists regarding potential uses of mung bean proteins and peptides. As mung bean has long been widely used as a food source, early studies evaluated mung bean nutritional value against the Food and Agriculture Organization of the United Nations (FAO)/the World Health Organization (WHO) amino acids dietary recommendations. The comparison demonstrated mung bean to be a good protein source, except for deficiencies in sulphur-containing amino acids, methionine and cysteine. Methionine and cysteine residues have been introduced into the 8S globulin through protein engineering technology. Subsequently, purified mung bean proteins and peptides have facilitated the study of their structural and functional properties. Two main types of extraction methods have been reported for isolation of proteins and peptides from mung bean flours, permitting sequencing of major proteins present in mung bean, including albumins and globulins (notably 8S globulin). However, the sequence for albumin deposited in the UniProt database differs from other sequences reported in the literature. Meanwhile, a limited number of reports have revealed other useful bioactivities for proteins and hydrolysed peptides, including angiotensin-converting enzyme inhibitory activity, anti-fungal activity and trypsin inhibitory activity. Consequently, several mung bean hydrolysed peptides have served as effective food additives to prevent proteolysis during storage. Ultimately, further research will reveal other nutritional, functional and bioactive properties of mung bean for uses in diverse applications. PMID:29545737

Mineralogical and chemical assessment of concrete damaged by the oxidation of sulfide-bearing aggregates: Importance of thaumasite formation on reaction mechanisms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodrigues, A.; Duchesne, J., E-mail: josee.duchesne@ggl.ulaval.ca; Fournier, B.

Damages in concrete containing sulfide-bearing aggregates were recently observed in the Trois-Rivieres area (Quebec, Canada), characterized by rapid deterioration within 3 to 5 years after construction. A petrographic examination of concrete core samples was carried out using a combination of tools including: stereomicroscopic evaluation, polarized light microscopy, scanning electron microscopy, X-ray diffraction and electron microprobe analysis. The aggregate used to produce concrete was an intrusive igneous rock with different metamorphism degrees and various proportions of sulfide minerals. In the rock, sulfide minerals were often surrounded by a thin layer of carbonate minerals (siderite). Secondary reaction products observed in the damagedmore » concrete include 'rust' mineral forms (e.g. ferric oxyhydroxides such as goethite, limonite (FeO (OH) nH{sub 2}O) and ferrihydrite), gypsum, ettringite and thaumasite. In the presence of water and oxygen, pyrrhotite oxidizes to form iron oxyhydroxides and sulphuric acid. The acid then reacts with the phases of the cement paste/aggregate and provokes the formation of sulfate minerals. Understanding both mechanisms, oxidation and internal sulfate attack, is important to be able to duplicate the damaging reaction in laboratory conditions, thus allowing the development of a performance test for evaluating the potential for deleterious expansion in concrete associated with sulfide-bearing aggregates.« less

Studies on the disturbance of glucuronide formation in infectious hepatitis

PubMed Central

Vest, M. F.; Fritz, E.

1961-01-01

The ability of the liver to form glucuronides was measured in 10 patients with infectious hepatitis. One test was done at the onset and another about four weeks later after the clinical symptoms had disappeared. N-acetyl-p-aminophenol (N.A.P.A.) or acetanilide was administered in doses ranging from 10 to 20 mg. per kg. body weight, either orally or by intravenous injection. N.A.P.A. is conjugated by the liver at the hydroxyl group and excreted in the urine as sulphuric and glucuronic acid conjugates. Total conjugated p-aminophenol, free N.A.P.A., and N.A.P.A. glucuronide were estimated in the urine of our patients. In the blood the disappearance of N.A.P.A. (free form) and the formation of N.A.P.A. glucuronide were traced. During the acute phase of hepatitis the excretion of total conjugated p-aminophenol and of N.A.P.A. glucuronide in the urine is lower than after recovery from the disease. Likewise free N.A.P.A. disappears more slowly from the circulation and the peak concentration of N.A.P.A. glucuronide in the serum remains lower at the onset of hepatitis than after clinical cure. These results indicate that glucuronide formation during the acute stage of infectious hepatitis is depressed, as are other transformation mechanisms, i.e., of hippuric acid. PMID:13925655

Distribution and mode of occurrence of radionuclides in phosphogypsum derived from Aqaba and Eshidiya Fertilizer Industry, South Jordan

USGS Publications Warehouse

Al-Hwaiti, M. S.; Zielinski, R.A.; Bundham, J.R.; Ranville, J.F.; Ross, P.E.

2010-01-01

Phosphogypsum (PG) is a by-product of the chemical reaction called the "wet process" whereby sulphuric acid reacts with phosphate rock (PR) to produce phosphoric acid, needed for fertilizer production. Through the wet process, some impurities naturally present in the PR become incorporated in PG, including U decay-series radionuclides, are the main important concern which could have an effect on the surrounding environment and prevent its safe utilization. In order to determine the distribution and bioavailability of radionuclides to the surrounding environment, we used a sequential leaching of PG samples from Aqaba and Eshidiya fertilizer industry. The results showed that the percentages of 226Ra and 210Pb in PG are over those in the corresponding phosphate rocks (PG/PR), where 85% of the 226Ra and 85% of the 210Pb fractionate to PG. The sequential extraction results exhibited that most of 226Ra and 210Pb are bound in the residual phase (non-CaSO4) fraction ranging from 45-65% and 55%-75%, respectively, whereas only 10%-15% and 10%-20% respectively of these radionuclides are distributed in the most labile fraction. The results obtained from this study showed that radionuclides are not incorporated with gypsum itself and may not form a threat to the surrounding environment. ?? 2010 Science Press, Institute of Geochemistry, CAS and Springer Berlin Heidelberg.

Bioleaching of spent Ni-Cd batteries by continuous flow system: effect of hydraulic retention time and process load.

PubMed

Zhao, Ling; Yang, Dong; Zhu, Nan-Wen

2008-12-30

Spent Ni-Cd batteries bring a severe environmental problem that needs to be solved urgently. A novel continuous flow two-step leaching system based on bioleaching was introduced to dissolve heavy metals in batteries. It consists of an acidifying reactor which was used to culture indigenous thiobacilli and a leaching reactor which was used to leach metals from spent batteries. The indigenous acidophilic thiobacilli in sewage sludge was used as the microorganisms and the sludge itself as culture medium. Bioleaching tests at different hydraulic retention time (HRT) and process load in the leaching reactor were performed. The results showed that the longer the HRT (1, 3, 6, 9 and 15 days) was, the more time required to achieve the complete leaching of Ni, Cd and Co. The maximum dissolution of cadmium and cobalt was achieved at higher pH values (3.0-4.5) while the leaching of nickel hydroxide and nickel in metallic form (Ni0) were obtained separately in different acidity (pH 2.5-3.5). It cost about 25, 30 and more than 40 days to remove all of the three heavy metals with the process load of two, four and eight Ni-Cd batteries under the conditions that the ingoing bio-sulphuric acid was 1Ld(-1) and HRT was 3 days.

Porosity change after gypsum crust formation on macro-porous limestones

NASA Astrophysics Data System (ADS)

Dewanckele, Jan; Cnudde, Veerle; de Kock, Tim; Boone, Marijn; Boone, Matthieu; van Hoorebeke, Luc; Jacobs, Patric

2010-05-01

The deterioration of stone is a complex process in which physical, biological and chemical mechanisms are involved. In this research, pore structure changes inside two types of porous limestone were analyzed before, during and after strong acid tests with SO2. Sulphatation and crust formation phenomena on natural building stones exposed to a polluted environment, are largely described in literature. As far as rocks rich in calcium carbonate are concerned, the main processes involved are the dissolution of the calcium carbonate and the formation of gypsum (CaSO4.2H2O) in presence of an acid atmosphere. The low mobility of this newly formed salt favours its accumulation in porous materials and at the surface of less porous media. The main actor in the process of gypsum crystallization on limestone is the aggressive sulphur dioxide gas (SO2). In this study, the Savonnières and Euville limestone were subjected to tests with a strong acid. According to the standard EN 13919:2002E, samples were put in acid environment for 21 days. At the bottom of the container a mixture of 500 ± 10 ml H2SO3 and 150 ± 10 ml de-mineralized H2O was added. No airborne particles or oxides of nitrogen (NOx) were added. Before exposure, after 6 days in the polluted environment and at the end of the test, the two samples were scanned with X-ray computed tomography (X-ray CT) at the Centre for X-ray Tomography at Ghent University, Belgium (UGCT; www.ugct.ugent.be). This visualization technique allows 2D and 3D reconstructions on a micrometer scale of the internal structure of an object without damaging the material. It thus enables to scan the same sample in a sequential way. In order to obtain information about the sample's interior of which the characteristics can be compared before, during and after the test, the same scanning parameters (exposure time, amount of frames, energy, etc.) were used. In addition, the same adjustments like beam hardening correction, normalizing, ring and spot filter, etc. were applied for the reconstruction. Total porosity, open and closed porosity and radial porosity were calculated for each sample by using the in-house developed software program Morpho+. The analysis of the various scans revealed that the Euville limestone developed a distinct gypsum crust, behind which a secondary porous layer of 100 μm thickness had developed. Inside the sample the porosity decreased by infilling of the large pore spaces with gypsum. However, after 6 days exposure the total porosity of the sample increased from 5.70% to 8.45%. In this case, the formation of secondary porosity behind the newly formed exterior gypsum layer prevailed upon the crystallizing of gypsum inside the pores located in the sample's interior. Also, the firstly formed gypsum crystals prevented the further interaction of the sulphuric acid with the stone material. After 21 days, the total porosity of the sample still reached 8.45%. The results of the radial porosity measurements were also the same after 6 and 21 days, indicating that the secondary porosity and the filling of pores inside the samples were stabilized. On the other hand, the gypsum crust on the Savonnières limestone was less visible. No secondary formed porous layer was measured and the total porosity decreased from 12.10% to 10.94% after 6 days and further to 10.31% at the end of the test. The decrease of porosity was still measurable at a depth of 500 μm inside the sample. The combination of micro-CT, image analysis and induced weathering tests are a promising combination of tools and techniques that allow for a better understanding of gypsum crust formation and pore structure change just behind the crust and deeper inside the rock sample.

Moisture Management Behaviour of Knitted Fabric from Structurally Modified Ring and Vortex Spun Yarn

NASA Astrophysics Data System (ADS)

Sharma, Navendu; Kumar, Pawan; Bhatia, Dinesh; Sinha, Sujit Kumar

2016-10-01

The acceptability of a new product is decided by its performance, level of improvement in quality and economy of production. The basic aim of generating micro pores in a textile structure is to provide better thermo-physiological comfort by enhancing the breathability and hence improving moisture management behaviour. In the present study, an attempt has been made to create a relatively more open structure through removal of a component. A comparative assessment with a homogeneous and parent yarn was also made. Yarns of two linear densities, each from ring and vortex spinning systems were produced using 100 % polyester and 80:20 polyester/cotton blend. The modified yarn was produced by removing a component, viz; cotton, by treatment with sulphuric acid from the blended yarn. The knitted fabric from modified yarn was found to show significant improvement in air permeability, water vapour permeability and total absorbency while the wicking characteristic was found to decline.

Iron concentration, bioavailability, and nutritional quality of polished rice affected by different forms of foliar iron fertilizer.

PubMed

He, Wanling; Shohag, M J I; Wei, Yanyan; Feng, Ying; Yang, Xiaoe

2013-12-15

The present study compared the effects of four different forms of foliar iron (Fe) fertilizers on Fe concentration, bioavailability and nutritional quality of polished rice. The results showed that foliar fertilisation at the anthesis stage was an effective way to promote Fe concentration and bioavailability of polished rice, especially in case of DTPA-Fe. Compared to the control, foliar application of DTPA-Fe increased sulphur concentration and the nutrition promoter cysteine content, whereas decreased phosphorus concentration and the antinutrient phytic acid content of polished rice, as a result increased 67.2% ferrtin formation in Caco-2 cell. Moreover, foliar DTPA-Fe application could maintain amylase, protein and minerals quality of polished rice. According to the current study, DTPA-Fe is recommended as an excellent foliar Fe form for Fe biofortification program. Copyright © 2013 Elsevier Ltd. All rights reserved.

Rapid and solvent-saving liquefaction of woody biomass using microwave-ultrasonic assisted technology.

PubMed

Lu, Zexiang; Wu, Zhengguo; Fan, Liwei; Zhang, Hui; Liao, Yiqiang; Zheng, Deyong; Wang, Siqun

2016-01-01

A novel process to rapidly liquefy sawdust using reduced quantities of solvent, was successfully carried out via microwave-ultrasonic assisted technology (MUAT) in a sulphuric acid/polyethylene glycol 400-glycerol catalytic system. The influences of some key parameters on the liquefaction yield were investigated. The results showed that compared with traditional liquefaction, the introduction of MUAT allowed the solvent dosage to be halved and shortened the liquefaction time from 60 to 20 min. The liquefaction yield reached 91% under the optimal conditions. However, the influence on the yield of some parameters such as catalyst concentration, was similar to that of traditional liquefaction, indicating that the application of MUAT possibly only intensified heat and mass transfer rather than altering either the degradation mechanism or pathway. The introduction of MUAT as a process intensification technology has good industrial application potential for woody biomass liquefaction. Copyright © 2015 Elsevier Ltd. All rights reserved.

SAD phasing with in-house cu Ka radiation using barium as anomalous scatterer.

PubMed

Dhanasekaran, V; Velmurugan, D

2011-12-01

Phasing of lysozyme crystals using co-crystallized barium ions was performed using single-wavelength anomalous diffraction (SAD) method using Cu Ka radiation with in-house source of data collection. As the ion binding sites vary with respect to the pH of the buffer during crystallization, the highly isomorphic forms of lysozyme crystals grown at acidic and alkaline pH were used for the study. Intrinsic sulphur anomalous signal was also utilized with anomalous signal from lower occupancy ions for phasing. The study showed that to solve the structure by SAD technique, 2.8-fold data redundancy was sufficient when barium was used as an anomalous marker in the in-house copper X-ray radiation source for data collection. Therefore, co-crystallization of proteins with barium containing salt can be a powerful tool for structure determination using lab source.

Extraction of diatoms from (cotton) clothing for forensic comparisons.

PubMed

Uitdehaag, Stefan; Dragutinovic, Aleksandar; Kuiper, Irene

2010-07-15

Diatoms in clothing can be used to determine contact with surface water and contact with a specific water source, which can help link suspects to crime scenes. However, for the study of diatoms it is imperative that they are first extracted from the clothing under investigation. In this study we tested three methods for extracting diatoms from cotton clothing: rinsing with water (RW), rinsing with ethanol (RE) and the dissolution of cotton with nitric and sulphuric acid (DI). The DI method produced the highest average yield and can be used to determine contact with water. The RE method extracted reproducible numbers of diatoms from two different T-shirts and the resulting species compositions were similar to their relevant reference water samples. Therefore, we present rinsing with ethanol as an effective extraction method for the qualitative and quantitative analysis of diatoms in (cotton) clothing. (c) 2010 Elsevier Ireland Ltd. All rights reserved.

The production of oxygen and metal from lunar regolith

NASA Astrophysics Data System (ADS)

Schwandt, Carsten; Hamilton, James A.; Fray, Derek J.; Crawford, Ian A.

2012-12-01

The present article summarises the various methods that have been, and still are, explored for the production of oxygen from lunar materials. These include the classical concepts based on chemical reduction with hydrogen or methane, vapour phase pyrolysis, sulphuric acid treatment, and molten oxide electrolysis. Our main focus in this paper is on a novel approach developed at the University of Cambridge that employs molten salt electrochemistry to achieve the combined winning of oxygen and metal from solid lunar materials of varying composition. This makes the Cambridge process attractive because it will work equally well in mare as in highland regions. We also discuss the implications of the recent apparent discovery of water ice at the poles of the Moon and conclude that, even if this discovery is confirmed, it will nevertheless be desirable to provide oxygen at non-polar localities, and the Cambridge process is a strong candidate for achieving this.

Complexation of nitrogen and sulphur donor Schiff's base ligand to Cr(III) and Ni(II) metal ions: synthesis, spectroscopic and antipathogenic studies.

PubMed

Sharma, Amit Kumar; Chandra, Sulekh

2011-01-01

2,6-diacetyl pyridine based ligand was synthesized by the reaction of 2,6-diacetyl pyridine with thiocarbohydrazide in presence of acetic acid. The coordination compounds with Cr(III) and Ni(II) metal ions having [Cr(L)X]X2 and [Ni(L)X]X compositions (where L=ligand and X=NO3-, Cl- and CH3COO-) were synthesized and characterized by physicochemical and spectral studies. The studies like elemental analyses, molar conductance measurements, magnetic susceptibility measurements, IR, UV-Vis, NMR, mass and EPR reveal that the complexes are octahedral. The compounds were examined against the pathogenic fungal and bacterial strains like Alternaria brassicae, Aspergillus niger, Fusarium oxysporum, Xanthomonas compestris and Pseudomonas aeruginosa. A. niger causes the diseases Apergillosis and Otomycosis in humans. Copyright © 2010. Published by Elsevier B.V.

Ammonium and nitrate tolerance in lichens.

PubMed

Hauck, Markus

2010-05-01

Since lichens lack roots and take up water, solutes and gases over the entire thallus surface, these organisms respond more sensitively to changes in atmospheric purity than vascular plants. After centuries where effects of sulphur dioxide and acidity were in the focus of research on atmospheric chemistry and lichens, recently the globally increased levels of ammonia and nitrate increasingly affect lichen vegetation and gave rise to intense research on the tolerance of lichens to nitrogen pollution. The present paper discusses the main findings on the uptake of ammonia and nitrate in the lichen symbiosis and to the tolerance of lichens to eutrophication. Ammonia and nitrate are both efficiently taken up under ambient conditions. The tolerance to high nitrogen levels depends, among others, on the capability of the photobiont to provide sufficient amounts of carbon skeletons for ammonia assimilation. Lowly productive lichens are apparently predisposed to be sensitive to excess nitrogen. Copyright 2010 Elsevier Ltd. All rights reserved.

Formulation and Evaluation of a Novel Adhesive Film for Use in Composite Patch Repair

NASA Astrophysics Data System (ADS)

Tsamasphyros, G.; Kalkanis, K.; Maroulas, P.; Anthoulis, G. I.; Grigoryeva, O.

2008-08-01

The current work focuses on the testing of a novel material used as an adhesive film in Composite Patch Repair (CPR). A series of Differential Scanning Calorimetry (DSC) results along with various curing cycles not only led to the optimum material composition but also demonstrated the compatibility to the composite pre-impregnated patches. This in turn was subjected to mechanical testing including shear strength measurements. The substrate was chosen to be 2017 T4 aluminium alloy which is customarily used in the aerospace industry, taking into account that CPR is a technique mainly applied in this field. The subsequent surface preparation of the specimens was investigated for the specified context resulting to the selection of the Ferric Sulphate Sulphuric acid etching process. Finally, a series of specimens representing actual skin repairs were created and subjected to cyclic loading, specifying the suitability of the novel material, compared to commercially available materials.

TiO2 and its composites as effective photocatalyst for glucose degradation processes

NASA Astrophysics Data System (ADS)

Kukh, A. A.; Ivanenko, I. M.; Astrelin, I. M.

2018-03-01

Titanium-dioxide photocatalyst was impregnated onto the activated carbon using originally developed low-temperature sol-gel method to form a TiO2:AC composite material. 15% (mass.) solution Ti2(SO4)3 in sulphuric acid was used as a precursor for photocatalyst synthesis. The highly effective composite material was obtained through a combination of properties of titanium dioxide and activated carbon. Synthesized composites TiO2 with activated carbon demonstrate highly developed surface characteristics and exhibit significantly higher activity in comparison with samples of pure TiO2 synthesized the same way, existing analogues of pure TiO2 synthesized from TiCl3 and even industrial photocatalyst. This was testified by the degradation of 1% aqueous glucose solution using TiO2:AC, samples of pure TiO2 and commercial TiO2 AEROXIDE® TiO2 P25 produced by EVONIK Industries.

Method for producing and treating coal gases

DOEpatents

Calderon, Albert

1990-01-01

A method of generating a de-sulphurized volatile matter and a relatively low Btu gas includes the initial step of pyrolyzing coal to produce volatile matter and a char. The volatile matter is fed to a first de-sulphurizer containing a de-sulphurizing agent to remove sulphur therefrom. At the same time, the char is gasified to produce a relatively low Btu gas. The low Btu gas is fed to a second de-sulphurizer containing the de-sulphurizing agent to remove sulphur therefrom. A regenerator is provided for removing sulphur from the de-sulphurizing agent. Portions of the de-sulphurizing agent are moved among the first de-sulphurizer, the second de-sulphurizer, and the regenerator such that the regenerator regenerates the de-sulphurizing agent. Preferably, the portions of the de-sulphurizing agent are moved from the second de-sulphurizer to the first de-sulphurizer, from the first de-sulphurizer to the regenerator, and from the regenerator to the second de-sulphurizer.

SO 2 oxidation in an entraining cloud model with explicit microphysics

NASA Astrophysics Data System (ADS)

Bower, K. N.; Hill, T. A.; Coe, H.; Choularton, T. W.

A model of the chemical evolution of the droplets in a hill-cap cloud is presented. The chemistry of individual droplets forming on cloud condensation nuclei of differing size and chemical composition is considered, and the take-up of species from the gas phase by the droplets is treated explicity for the droplet population. Oxidation of S(IV) dissolved in cloud droplets is assumed to be dominated by hydrogen peroxide and ozone. Hydrogen peroxide is normally found to be the dominant oxidant for the oxidation of sulphur dioxide (except in the presence of substantial concentrations of ammonia gas, which increases droplet pH and the contribution made by the oxidant ozone). The entrainment of hydrogen peroxide from above the cloud top increases the amount of sulphate produced in conditions where the reaction is otherwise oxidant limited by the availability hydrogen peroxide. These conditions occur when there are high concentrations of sulphur dioxide accompanied by low cloudwater pH values. Within droplets formed on sodium chloride aerosol, reduced levels of acidity lead to an increase in sulphate production as a result of an enhanced reaction between SO 2 and the oxidant ozone. This results in an overall higher increase in cloudwater sulphate than would be expected assuming an even distribution of all reactants amongst the droplets. In addition, concentrations of the hydrogen sulphite ion predicted to occur in the cloudwater can be substantially in excess of those predicted from the bulk cloudwater pH. This is consistent with recent observations.

Enhanced phyto-extraction of cadmium and zinc using rapeseed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghani, M.; Slycken, S.V.; Meers, E.

2013-07-01

In a green house pot experiment, the effects of three amendments, sulphur (S), ammonium sulphate ((NH{sub 4}){sub 2}SO{sub 4}) and ethylenediaminetetracetic acid (EDTA) were tested for phyto-extraction of Cd and Zn by rapeseed (Brassica napus L.). Elemental sulphur was applied as 20.00, 60.00, and 120.00 mg.kg{sup -1} soil. EDTA was tested at a dose of 585.00 mg.kg{sup -1} soil, and (NH{sub 4}){sub 2}SO{sub 4}) at a rate of 0.23 mg.kg{sup -1} soil. All treatments received a base fertilization (Hogland) before sowing. Plants were harvested after 51 days of growth and shoot dry matter and soil samples were analysed for metalmore » contents. All amendments caused a significant increase in Cd and Zn contents in plant shoots of all treatments than control treatment. Further, EDTA was most effective for extraction metals concentrations in shoot biomass but the plants showed significant signs of toxicity and yield were severely depressed. The addition of sulfur favorably influenced plant biomass production. The fertilized ammonium sulfate treatment resulted in the highest phyto-extraction of Cd and Zn and the amounts of these metals accumulated in plant shoot exceeded by a factor of 4 and 3 respectively. Finally, Brassica napus could be used for soil remediation keeping its other uses which will make the contaminated site income generating source for the farmers. (authors)« less

Sultr4;1 mutant seeds of Arabidopsis have an enhanced sulphate content and modified proteome suggesting metabolic adaptations to altered sulphate compartmentalization

PubMed Central

2010-01-01

Background Sulphur is an essential macronutrient needed for the synthesis of many cellular components. Sulphur containing amino acids and stress response-related compounds, such as glutathione, are derived from reduction of root-absorbed sulphate. Sulphate distribution in cell compartments necessitates specific transport systems. The low-affinity sulphate transporters SULTR4;1 and SULTR4;2 have been localized to the vacuolar membrane, where they may facilitate sulphate efflux from the vacuole. Results In the present study, we demonstrated that the Sultr4;1 gene is expressed in developing Arabidopsis seeds to a level over 10-fold higher than the Sultr4;2 gene. A characterization of dry mature seeds from a Sultr4;1 T-DNA mutant revealed a higher sulphate content, implying a function for this transporter in developing seeds. A fine dissection of the Sultr4;1 seed proteome identified 29 spots whose abundance varied compared to wild-type. Specific metabolic features characteristic of an adaptive response were revealed, such as an up-accumulation of various proteins involved in sugar metabolism and in detoxification processes. Conclusions This study revealed a role for SULTR4;1 in determining sulphate content of mature Arabidopsis seeds. Moreover, the adaptive response of sultr4;1 mutant seeds as revealed by proteomics suggests a function of SULTR4;1 in redox homeostasis, a mechanism that has to be tightly controlled during development of orthodox seeds. PMID:20426829

The Effect of Parasite Infection on Stable Isotope Turnover Rates of δ15N, δ13C and δ34S in Multiple Tissues of Eurasian Perch Perca fluviatilis.

PubMed

Yohannes, Elizabeth; Grimm, Claudia; Rothhaupt, Karl-Otto; Behrmann-Godel, Jasminca

2017-01-01

Stable isotope analysis of commercially and ecologically important fish can improve understanding of life-history and trophic ecology. However, accurate interpretation of stable isotope values requires knowledge of tissue-specific isotopic turnover that will help to describe differences in the isotopic composition of tissues and diet. We performed a diet-switch experiment using captive-reared parasite-free Eurasian perch (Perca fluviatilis) and wild caught specimens of the same species, infected with the pike tapeworm Triaenophorus nodulosus living in host liver tissue. We hypothesize that metabolic processes related to infection status play a major role in isotopic turnover and examined the influence of parasite infection on isotopic turn-over rate of carbon (δ13C), nitrogen (δ15N) and sulphur (δ34S) in liver, blood and muscle. The δ15N and δ13C turnovers were fastest in liver tissues, followed by blood and muscle. In infected fish, liver and blood δ15N and δ13C turnover rates were similar. However, in infected fish, liver and blood δ13C turnover was faster than that of δ15N. Moreover, in infected subjects, liver δ15N and δ13C turnover rates were three to five times faster than in livers of uninfected subjects (isotopic half-life of ca.3-4 days compared to 16 and 10 days, respectively). Blood δ34S turnover rate were about twice faster in non-infected individuals implying that parasite infection could retard the turnover rate of δ34S and sulphur containing amino acids. Slower turnover rate of essential amino acid could probably decrease individual immune function. These indicate potential hidden costs of chronic and persistent infections that may have accumulated adverse effects and might eventually impair life-history fitness. For the first time, we were able to shift the isotope values of parasites encapsulated in the liver by changing the dietary source of the host. We also report variability in isotopic turnover rates between tissues, elements and between infected and parasite-free individuals. These results contribute to our understanding of data obtained from field and commercial hatcheries; and strongly improve the applicability of the stable isotope method in understanding life-history and trophic ecology of fish populations.

The Effect of Parasite Infection on Stable Isotope Turnover Rates of δ15N, δ13C and δ34S in Multiple Tissues of Eurasian Perch Perca fluviatilis

PubMed Central

Yohannes, Elizabeth; Grimm, Claudia; Rothhaupt, Karl-Otto; Behrmann-Godel, Jasminca

2017-01-01

Stable isotope analysis of commercially and ecologically important fish can improve understanding of life-history and trophic ecology. However, accurate interpretation of stable isotope values requires knowledge of tissue-specific isotopic turnover that will help to describe differences in the isotopic composition of tissues and diet. We performed a diet-switch experiment using captive-reared parasite-free Eurasian perch (Perca fluviatilis) and wild caught specimens of the same species, infected with the pike tapeworm Triaenophorus nodulosus living in host liver tissue. We hypothesize that metabolic processes related to infection status play a major role in isotopic turnover and examined the influence of parasite infection on isotopic turn-over rate of carbon (δ13C), nitrogen (δ15N) and sulphur (δ34S) in liver, blood and muscle. The δ15N and δ13C turnovers were fastest in liver tissues, followed by blood and muscle. In infected fish, liver and blood δ15N and δ13C turnover rates were similar. However, in infected fish, liver and blood δ13C turnover was faster than that of δ15N. Moreover, in infected subjects, liver δ15N and δ13C turnover rates were three to five times faster than in livers of uninfected subjects (isotopic half-life of ca.3-4 days compared to 16 and 10 days, respectively). Blood δ34S turnover rate were about twice faster in non-infected individuals implying that parasite infection could retard the turnover rate of δ34S and sulphur containing amino acids. Slower turnover rate of essential amino acid could probably decrease individual immune function. These indicate potential hidden costs of chronic and persistent infections that may have accumulated adverse effects and might eventually impair life-history fitness. For the first time, we were able to shift the isotope values of parasites encapsulated in the liver by changing the dietary source of the host. We also report variability in isotopic turnover rates between tissues, elements and between infected and parasite-free individuals. These results contribute to our understanding of data obtained from field and commercial hatcheries; and strongly improve the applicability of the stable isotope method in understanding life-history and trophic ecology of fish populations. PMID:28046021

Landslide-induced weathering: insight from a deep bedrock tunnel in Taiwan and implications for the carbon cycle

NASA Astrophysics Data System (ADS)

Martin, C. E.; Galy, A.; Calmels, D.; Hovius, N.; Bickle, M.; Chen, M.

2012-12-01

We present new groundwater chemistry data from inside a 520 m-long, un-cased bedrock tunnel in Taroko Gorge, Taiwan. The tunnel cuts through a ~ 250 m ridge of steeply-dipping meta-sediments (schists and marbles) and exhibits water flow characteristic of deep groundwater and slow surface runoff as defined by Calmels et al. (2011). For comparison, surface runoff from the tunnel face is also presented. In October 2009, catastrophic failure resulted in a landslide, removing ~ 10 m-deep of bedrock from the entire ridge face directly above the tunnel entrance. Groundwater was collected from several drip sites in September 2009 and from the same drip sites in May, June, July and August 2010. The chemistry of the water dripping close to the tunnel entrance disrupted by the landslide implies that the post-landslide groundwater was from a meteoric source with negligible evapotranspiration demonstrating that the geomorphic perturbation allowed for the relatively rapid flushing of underlying bedrock fractures. The drop in [Cl-] of ~ 60 % was associated with a rise in the [SO42-] by a factor of ~ 4 and a positive shift in δ13C of the dissolved inorganic carbon (DIC) of ~ 12 ‰. This could imply that weathering products in the fresh post-landslide groundwater resulted from sulphuric acid weathering associated with a rise in the carbonate-derived DIC. The rise in the [SO42-] suggests that the landslide-induced exposure of fresh mineral surfaces resulted in the relatively rapid oxidation of pyrite, generating sulphuric acid, which then acted as the primary weathering agent. Given that [Ca2+] and [HCO3-] remained constant, secondary carbonate precipitation also took place and the rise in the [Na+] by a factor of >7 associated with a rise in [Mg2+] and [K+] suggest that silicate dissolution had also been enhanced by the oxidation of pyrite. These results imply that landslides provide a mechanism for weathering in the deep critical zone, which in this case constitutes a net output of CO2 to the atmosphere. Calmels, D., Galy, A., Hovius, N., Bickle, M., West, J.A., Chen, M-C., Chapman, H. Contribution of deep groundwater to the weathering budget in a rapidly eroding mountain belt, Taiwan. 2011. Earth and Planetary Science Letters 303: 48-58.

Retrieval of Venus' cloud parameters from VIRTIS nightside spectra in the latitude band 25°-55°N

NASA Astrophysics Data System (ADS)

Magurno, Davide; Maestri, Tiziano; Grassi, Davide; Piccioni, Giuseppe; Sindoni, Giuseppe

2017-09-01

Two years of data from the M-channel of the Visible and InfraRed Thermal Imaging Spectrometer (VIRTIS), on board the European Space Agency mission Venus Express operating around the planet Venus, are analysed. Nocturnal data from a nadir viewpoint in the latitude band 25°N-55°N are selected for their configuration advantages and maximisation of the scene homogeneity. A reference model, and radiance spectrum, is defined based on average accepted values of the Venus main atmospheric and cloud parameters found in the literature. Extensive radiative transfer simulations are performed to provide a synthetic database of more than 10 000 VIRTIS radiances representing the natural variability of the system parameters (atmospheric temperature profile, cloud H2Osbnd H2SO4 solution concentration and vertical distribution, particle size distribution density and modal radius). A simulated-observed fitting algorithm of spectral radiances in window channels, based on a weighting procedure accounting for the latitudinal observed radiance variations, is used to derive the best atmosphere-cloud configuration for each observation. Results show that the reference Venus model does not adequately reproduce the observed VIRTIS spectra. In particular, the model accounting for a constant sulphuric acid concentration along the vertical extent of the clouds is never selected as a best fit. The 75%/96% and 84%/96% concentrations (the first values refer to the upper cloud layers and the second values to the lower ones) are the most commonly retrieved models representing more than 85% of the retrieved cases for any latitudinal band considered. It is shown that the assumption of stratified concentration of aqueous sulphuric acid allows to adequately fit the observed radiance, in particular the peak at 1.74 μm and around 4 μm. The analysis of the results concerning the microphysics suggests larger radii for the upper cloud layers in conjunction with a large reduction of their number density with respect to the reference standard. Considerable variation of the particle concentration in the Venus' atmosphere is retrieved for altitudes between 60 and 70 km. The retrieved models also suggest that lower cloud layers have smaller particle radii and larger number density than expected from the reference model. Latitudinal variations of microphysical and chemical parameters are also analysed.

A role for gamma-glutamyl transpeptidase and the amino acid transport system xc- in cystine transport by a human pancreatic duct cell line.

PubMed Central

Sweiry, J H; Sastre, J; Viña, J; Elsässer, H P; Mann, G E

1995-01-01

1. The roles of the gamma-glutamyl cycle and the anionic amino acid transport system xc- in mediating L-cystine uptake were investigated in cultured human pancreatic duct PaTu 8902 cells. This cell line exhibits morphological features of normal pancreatic duct cells and expresses gamma-glutamyl transpeptidase (gamma-GT, EC 2.3.2.2), an enzyme involved in the metabolism and regulation of intracellular glutathione (GSH). 2. Uptake of L-cystine (10 microM) was linear for up to 10 min, temperature dependent, Na+ independent, saturable (Michaelis-Menten constant (Km), 86 +/- 25 microM; maximal velocity (Vmax), 109 +/- 33 nmol (mg protein)-1 h-1) and reduced by 80-90% by a 50-fold excess concentration of L-glutamate and L-homocysteic acid, but not L-aspartate. These transport properties resemble those described for system xc-, which exchanges cystine for intracellular glutamate. 3. Acivicin, a known inhibitor of gamma-GT, decreased gamma-GT activity from 2.58 +/- 0.96 to 0.97 +/- 0.11 mU (mg protein)-1 and decreased the initial rates of L-cystine and L-glutamine uptake by 41-55%. Anthglutin (1-gamma-L-glutamyl-2-(2-carboxyphenylhyl)hydrazine), a structurally different inhibitor of gamma-GT, also caused a concentration-dependent (0.01-1 mM) decrease in gamma-GT activity and L-cystine uptake. 4. Neither acivicin nor anthglutin inhibited the uptake of L-glutamate, a poor substrate for gamma-GT. 5. In the presence of a 500-fold excess concentration of glutamate, which should abolish entry of cystine via system xc-, the remaining fraction of cystine transport was inhibited by 50% by acivicin, suggesting that transport is, in part, dependent on the activity of gamma-GT. 6. Cystine transport was also 60-80% inhibited by a series of gamma-glutamyl amino acids (5 mM) including gamma-glutamyl-glutamate, gamma-glutamyl-glutamine and gamma-glutamyl-glycine. alpha-Dipeptides inhibited cystine transport by only 6-22%. 7. These findings demonstrate that in human pancreatic duct PaTu 8902 cells, cystine uptake is mediated by system xc- (50-60%) and the gamma-glutamyl cycle. Our results provide the first evidence linking gamma-GT with cystine transport in human epithelial cells and are of relevance in view of the importance of cystine as a sulphur amino acid source for GSH synthesis in cells exposed to oxidative stress. Images Figure 1 PMID:7658371

Stratospheric changes caused by geoengineering applications: potential repercussions and uncertainties

NASA Astrophysics Data System (ADS)

Kenzelmann, P.; Weisenstein, D.; Peter, T.; Luo, B. P.; Rozanov, E.; Fueglistaler, S.; Thomason, L. W.

2009-04-01

Anthropogenic greenhouse gas emissions tend to warm the global climate, calling for significant rapid emission reductions. As potential support measures various ideas for geoengineering are currently being discussed. The assessment of the possible manifold and as yet substantially unexplored repercussions of implementing geoengineering ideas to ameliorate climate change poses enormous challenges not least in the realm of aerosol-cloud-climate interactions. Sulphur aerosols cool the Earth's surface by reflecting short wave radiation. By increasing the amount of sulphur aerosols in the stratosphere, for example by sulphur dioxide injections, part of the anthropogenic climate warming might be compensated due to enhanced albedo. However, we are only at the beginning of understanding possible side effects. One such effect that such aerosol might have is the warming of the tropical tropopause and consequently the increase of the amount of stratospheric water vapour. Using the 2D AER Aerosol Model we calculated the aerosol distributions for yearly injections of 1, 2, 5 and 10 Mt sulphur into the lower tropical stratosphere. The results serve as input for the 3D chemistry-climate model SOCOL, which allows calculating the aerosol effect on stratospheric temperatures and chemistry. In the injection region the continuously formed sulphuric acid condensates rapidly on sulphate aerosol, which eventually grow to such extent that they sediment down to the tropical tropopause region. The growth of the aerosol particles depends on non-linear processes: the more sulphur is emitted the faster the particles grow. As a consequence for the scenario with continuous sulphur injection of totally 10 Mt per year, only 6 Mt sulphur are in the stratosphere if equilibrium is reached. According to our model calculations this amount of sulphate aerosols leads to a net surface forcing of -3.4 W/m2, which is less then expected radiative forcing by doubling of carbon dioxide concentration. Hence, larger injections might be required than previously assumed. Rasch et al. (2008) showed that smaller particles would be advantageous in terms of cooling the surface. However, with a continuous injection of sulphur dioxide into to lower tropical stratosphere aerosol size distributions with mode radii larger than 0.5 microns are likely to form. An additional complication is that the sedimenting particles tend to heat the tropical tropopause region and as a consequence the entry mixing ratio of water vapour increases. For the extreme scenario of 10 Mt/year injection SOCOL predicts an enhancement of the water vapour entry mixing ratio by more than 1 ppmv. This is predicted to have a significant impact on the radiative forcing and the total ozone, because of enhanced heterogeneous reactions and because the increased water vapour intensifies the hydrogen and chlorine catalysed ozone destruction cycles. The intense warming of the lower stratosphere further intensifies the catalytic ozone destruction cycles. Furthermore, the stratospheric circulation is predicted to change due to the strong heating of the lower stratosphere. As a consequence of the intensified meridional temperature gradient the polar vortices are strengthened with enhanced formation of polar stratospheric clouds and ozone depletion. The ozone loss due to changed stratospheric dynamic is four times larger than the ozone loss caused by the increase of aerosol surface for heterogeneous reactions, which would postpone the recovery of the ozone hole even more as already pointed out by Tilmes et al. [2008]. At the same time the uncertainties involved in the different modelling steps are tremendous. Model validation, by comparing model runs of the 1991 Mt. Pinatubo eruption with observations, reveals that the temperature increase in the lower stratosphere and the tropopause region is probably overestimated by SOCOL. Other CCMs show similar behaviour. This lets us conclude that with the present modelling tools we are not capable to reliably predict the changes in stratospheric climate following geoengineering applications. Rasch, P. J. et al. (2008), Exploring the geoengineering of climate using stratospheric sulfate aerosols: The role of particle size, Geophysical Research Letters, 35 (2), L02,809. Tilmes, S. et al. (2008), The sensitivity of polar ozone depletion to proposed geoengineering schemes, Science, 320 (5880), 1201-1204.

Environmental magnetism of intertrapean Deccan deposits: unravelling local paleoenvironmental during Phase 1 and 2

NASA Astrophysics Data System (ADS)

Font, Eric; Adatte, Thierry; Ponte, Jorge; Fantasia, Alicia; Mirão, José; Samant, Bandana; Mohabey, Dhananjay; Florindo, Fabio

2014-05-01

The Deccan phase 2 is a crucial period caracterized by the rapid eruptions of huge volume of continental flood basalts correlated in age to the mass extinction of the Cretaceous-Paleogene boundary. However, local to global paleonvironmental changes during the Deccan Phase 2 are still baddly known. Here we provide new environmental magnetic data coupled to scanning electron microscopy of intertrapean deposits from the Deccan Volcanic Province (India) in order to unravel local paleoenvironmental conditions during periods of volcanic quiescence in the aftermath of the Deccan Phase 1 and Phase 2. Our results show that the magnetic mineralogy of these lacustrine and fluvial sediments is composed by several populations of iron oxides and sulphur, with a large range of grain size, probably resulting from different source of magnetic carriers (aeolian, detrital and bio-chemical). The number of magnetic phases identified using unmixing Isothermal Remanence Magnetic techniques is significantly higher (2 to 4) in the Podgavan section equivalent to Phase 2 than in the other studied sections, interpreted to result from higher weathering rates (acidity) by correlation with index of chemical alteration. Detailed scanning electron microscopy analysis of the Podgavan section reveal a complex mineralogy constituted by detrital magnetite, spherical and framboidal magnetite, microsphere of silicon, pyrrhotite, sylvite, manganese oxides and sporangiospores. A peculiar interval observed in the middle part of the Podgavan section, and corresponding to a thin interval of organic-rich clay capped by a thin oxidized level of reddish clays, show the presence of calcite needles and very fine hematite pigment. Hematite pigment are systematically associated to voids and form structures comparable to the blueberry hematite formed on mars. The abrupt transition from organic-rich levels (reducing conditions) to red hematitic clays (oxidation) suggests drastic and abrupt paleoenvironmental changes and acid conditions during the Deccan Phase 2. Keywords: Deccan, lacustrine sediments, environmental magnetism, acid rain, climate, weathering, volcanism.

Complete genome sequence of Corynebacterium variabile DSM 44702 isolated from the surface of smear-ripened cheeses and insights into cheese ripening and flavor generation

PubMed Central

2011-01-01

Background Corynebacterium variabile is part of the complex microflora on the surface of smear-ripened cheeses and contributes to the development of flavor and textural properties during cheese ripening. Still little is known about the metabolic processes and microbial interactions during the production of smear-ripened cheeses. Therefore, the gene repertoire contributing to the lifestyle of the cheese isolate C. variabile DSM 44702 was deduced from the complete genome sequence to get a better understanding of this industrial process. Results The chromosome of C. variabile DSM 44702 is composed of 3, 433, 007 bp and contains 3, 071 protein-coding regions. A comparative analysis of this gene repertoire with that of other corynebacteria detected 1, 534 predicted genes to be specific for the cheese isolate. These genes might contribute to distinct metabolic capabilities of C. variabile, as several of them are associated with metabolic functions in cheese habitats by playing roles in the utilization of alternative carbon and sulphur sources, in amino acid metabolism, and fatty acid degradation. Relevant C. variabile genes confer the capability to catabolize gluconate, lactate, propionate, taurine, and gamma-aminobutyric acid and to utilize external caseins. In addition, C. variabile is equipped with several siderophore biosynthesis gene clusters for iron acquisition and an exceptional repertoire of AraC-regulated iron uptake systems. Moreover, C. variabile can produce acetoin, butanediol, and methanethiol, which are important flavor compounds in smear-ripened cheeses. Conclusions The genome sequence of C. variabile provides detailed insights into the distinct metabolic features of this bacterium, implying a strong adaption to the iron-depleted cheese surface habitat. By combining in silico data obtained from the genome annotation with previous experimental knowledge, occasional observations on genes that are involved in the complex metabolic capacity of C. variabile were integrated into a global view on the lifestyle of this species. PMID:22053731

Thermal mud maturation: organic matter and biological activity.

PubMed

Centini, M; Tredici, M R; Biondi, N; Buonocore, A; Maffei Facino, R; Anselmi, C

2015-06-01

Many of the therapeutic and cosmetic treatments offered in spas are centred on mud therapy, to moisturize the skin and prevent skin ageing and rheumatic diseases. Thermal mud is a complex matrix composed of organic and inorganic elements which contribute to its functions. It is a natural product derived from the long mixing of clay and thermal water. During its maturation, organic substances are provided by the microalgae, which develop characteristic of the composition of thermal water. The aim of this study was to identify methods for introducing objective parameters as a basis for characterizing thermal mud and assessing its efficacy. Samples of thermal mud were collected at the Saturnia spa, where there are several sulphureous pools. The maturation of the mud was evaluated by organic component determination using extractive methods and chromatographic analysis (HPLC, GC-MS, SPME). We also studied the radical scavenging activity of mud samples at different stages of maturation, in a homogeneous phase, using several tests (DPPH, ORAC, ABTS). We identified several classes of compounds: saturated and unsaturated fatty acids, hydroxyl acids, dicarboxylic acids, ketoacids, alcohols and others. SPME analysis showed the presence of various hydrocarbons compounds (C(11) -C(17)) and long-chain alcohols (C(12) -C(16)). Six or seven months seemed appropriate to complete the process of maturation, and the main effect of maturation time was the increase of lipids. Six-month mud showed the highest activity. The hydrophilic extract was more active than the lipophilic extract. The results indicate that maturation of thermal mud can be followed on the basis of the changes in its organic composition and antioxidant properties along the time. They also highlight the need to develop reference standards for thermal muds in relation to assess their use for therapeutic and cosmetic purposes. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Potential of fly ash for neutralisation of acid mine drainage.

PubMed

Qureshi, Asif; Jia, Yu; Maurice, Christian; Öhlander, Björn

2016-09-01

Lignite (PK), bituminous (FI) and biomass (SE) fly ashes (FAs) were mineralogically and geochemically characterised, and their element leachability was studied with batch leaching tests. The potential for acid neutralisation (ANP) was quantified by their buffering capacity, reflecting their potential for neutralisation of acid mine drainage. Quartz was the common mineral in FAs detected by XRD with iron oxide, anhydrite, and magnesioferrite in PK, mullite and lime in FI, and calcite and anorthite in SE. All the FAs had high contents of major elements such as Fe, Si, Al and Ca. The Ca content in SE was six and eight times higher compared to PK and FI, respectively. Sulphur content in PK and SE was one magnitude higher than FI. Iron concentrations were higher in PK. The trace element concentrations varied between the FAs. SE had the highest ANP (corresponding to 275 kg CaCO3 tonne(-1)) which was 15 and 10 times higher than PK and FI, respectively. The concentrations of Ca(2+), SO4 (2-), Na(+) and Cl(-) in the leachates were much higher compared to other elements from all FA samples. Iron, Cu and Hg were not detected in any of the FA leachates because of their mild to strong alkaline nature with pH ranging from 9 to 13. Potassium leached in much higher quantity from SE than from the other ashes. Arsenic, Mn and Ni leached from PK only, while Co and Pb from SE only. The concentrations of Zn were higher in the leachates from SE. The FAs used in this study have strong potential for the neutralisation of AMD due to their alkaline nature. However, on the other hand, FAs must be further investigated, with scaled-up experiments before full-scale application, because they might leach pronounced concentrations of elements of concern with decreasing pH while neutralising AMD.

Effect of feeding higher concentrations of limiting amino acids on performance, slaughter variables and nitrogen retention in broiler chicken fed graded levels of toasted guar (Cyamopsis tetragonoloba) meal.

PubMed

Rao, S V Rama; Raju, M V L N; Prakash, B; Rajkumar, U; Srilatha, T; Reddy, E P K

2018-06-01

An experiment was conducted to study the effect of supplementing higher concentrations (100 vs. 110%) of critical amino acids (CAA) on performance (body weight gain - BWG, feed efficiency - FE), slaughter variables and nitrogen retention in broiler chicken (1-6 weeks of age) fed graded levels of toasted guar meal (TGM) as a protein source in diets. The TGM was included at five graded concentrations (0, 50, 100, 150and200 g/kg) in iso-caloric and iso-protein diets with either the recommended concentration (100%) of CAA (lysine, total sulphur amino acids, threonine, tryptophan and valine) or at 10% higher (110%) concentration. A metabolism trial of three-day duration was conducted during sixth week of age to study nitrogen retention. The TGM levels and CAA concentration at 21 or 42 d of age did not influence BWG, FI and FE. BWG was not affected with inclusion of TGM up to 100 g/kg in starter and overall production (1 - 42 d of age) phases. The FE improved with TGM supplementation during starter phase, while at the end of experiment (42 d), FE was depressed by inclusion of TGM in dose dependant manner. All performance variables improved with increase in concentration of CAA from 100 to 110%. Breast meat weight improved and abdominal fat weight reduced with higher levels of CAA in diet. Retention of nitrogen reduced with increase in level of TGM in broiler diet. Increasing concentrations of CAA in diet improved nitrogen retention. It was concluded that TGM could be incorporated up to 100 g/kg with 100% CAA and up to 150 g/kg with 110% CAA without affecting performance. Increasing CAA concentration (110%) in diets significantly improved BWG and FE (21 and 42 d), breast meat weight and nitrogen retention in broiler chicken.

Microbial leaching of toxic metals and arsenic from a heap consisting of heavily polluted soil

NASA Astrophysics Data System (ADS)

Groudev, Stoyan; Georgiev, Plamen; Spasova, Irena; Nicolova, Marina

2014-05-01

Soil heavily polluted with toxic heavy metals (mainly Cu, Zn, Cd) and arsenic was subjected to microbial cleanup in a heap specially constructed for this purpose. The heap was located on an impermeable geomembrane, had the shape of a truncated pyramid and contained about 240 tons of soil collected mainly from the horizon A. The soil was highly acidic (with an initial pH of about 3.2) and was preliminarily crushed to minus 2.5 cm particle size. The pollutants were present mainly as the relevant sulphide minerals and the soil was inhabited by different microorganisms, including some acidophilic chemolithotrophic bacteria able to oxidize sulphides and to solubilize the relevant toxic elements. The heap possessed systems for irrigation and aeration and was surrounded by ditches to collect the drainage heap effluents containing the dissolved pollutants. The treatment of the soil was carried out by means of interrupted irrigation with leach solutions containing diluted sulphuric acid (to maintain pH in the heap within the range of about 2.5 - 2.8) and ammonium and phosphate ions to maintain the microbial growth. The treatment was carried out for a period of about two years during different climatic seasons. After the end of leaching the soil was subjected to some conventional melioration procedures such as liming, grassing, moulching, addition of fertilizers and animal manure and periodic ploughing and irrigation to increase its quality to levels suitable for agricultural utilization.

Investigating a Sulphate-Nitrate Chemical Indirect Effect over Europe from 1980-2010

NASA Astrophysics Data System (ADS)

Pearce, H.; Mann, G. W.; Arnold, S.; O'Connor, F.; Conibear, L.; Turnock, S.; Rumbold, S.; Benduhn, F.

2017-12-01

Sulphur dioxide emission reductions have been successful in reducing surface sulphate concentrations over Europe between 1980 and 2010, with positive implications for air quality and human health. However the response of nitrate aerosol concentrations to declining NOx emissions has been non-linear. Previous studies have indicated that decreasing ammonium sulphate formation, as a result of SO2 emission reduction, may be partly responsible for this non-linearity by increasing the availability of ammonia and, hence, indirectly increasing ammonium nitrate aerosol formation. We use the UM-UKCA composition-climate model, including the GLOMAP interactive aerosol microphysics module and a recently developed `hybrid' dissolution solver (HyDis), to investigate the size-resolved partitioning of ammonia and nitric acid to the particle phase over Europe in the period 1980 to 2010. Anthropogenic emissions of SO2, NOx and NH3 are included from the MACCity inventory and change by approximately -79%, -33% and +30% respectively over Europe in this time. We evaluate the UM-UKCA simulated 1980-2010 variability in nitrate, ammonium and sulphate aerosol mass concentrations and aerosol pH, with comparison to EMEP observations, and isolate the indirect influence of reduced SO2 emissions on nitrate formation. Preliminary sensitivity tests indicate that simulated nitrate aerosol concentrations over Europe were 8% higher in 2009 than they would have been if SO2 emissions had not been reduced. The implications of this change for air quality, aerosol acidity and regional climate will be presented.

Assessment of the Brettanomyces bruxellensis metabolome during sulphur dioxide exposure.

PubMed

Vigentini, Ileana; Joseph, C M Lucy; Picozzi, Claudia; Foschino, Roberto; Bisson, Linda F

2013-11-01

Brettanomyces bruxellensis displays a high degree of genotypic and phenotypic polymorphism and is the main yeast species involved in wine spoilage. The innate resistance of 108 B. bruxellensis strains to the antimicrobial agent SO2 used in winemaking was investigated. Nineteen strains (17.6%) were sensitive to SO2 , failing to grow at the lowest concentration tested (0.1 mg L(-1) molecular SO2). Twenty-nine strains (26.8%) grew at 0.1 mg L(-1), 42 strains (38.9%) grew at 0.2 mg L(-1) , and 16 strains (14.8%) were able to grow as high as 0.4 mg L(-1) mol. SO2. Two strains able to grow in the presence of 0.6 mg L(-1) mol. SO2 were further studied by GCMS-TOF analysis to define the metabolic response to SO2 treatment. Two hundred and fifty-three intracellular metabolites were detected. The main effect observed was a decrease in cytoplasmic levels of polyols and an increase in levels of some amino acids, alanine, glutamic acid, glycine, proline, 5-oxoproline, serine and valine, which were significantly accumulated in the presence of SO2. No alteration in the pentose phosphate pathway was observed, suggesting NADPH usage could be diverted to other pathways. Finally, a change in metabolites involved in the glycerophospholipid pathway (glycerol-3-phosphate and myo-inositol) was also found. © 2013 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

Kinetics of dissolution of thorium and uranium doped britholite ceramics

NASA Astrophysics Data System (ADS)

Dacheux, N.; Du Fou de Kerdaniel, E.; Clavier, N.; Podor, R.; Aupiais, J.; Szenknect, S.

2010-09-01

In the field of immobilization of actinides in phosphate-based ceramics, several thorium and uranium doped britholite samples were submitted to leaching tests. The normalized dissolution rates determined for several pH values, temperatures and acidic media from the calcium release range from 4.7 × 10 -2 g m -2 d -1 to 21.6 g m -2 d -1. Their comparison with that determined for phosphorus, thorium and uranium revealed that the dissolution is clearly incongruent for all the conditions examined. Whatever the leaching solution considered, calcium and phosphorus elements were always released with higher RL values than the other elements (Nd, Th, U). Simultaneously, thorium was found to quickly precipitate as alteration product, leading to diffusion phenomena for uranium. For all the media considered, the uranium release is higher than that of thorium, probably due to its oxidation from tetravalent oxidation state to uranyl. Moreover, the evaluation of the partial order related to proton concentration and the apparent energy of activation suggest that the reaction of dissolution is probably controlled by surface chemical reactions occurring at the solid/liquid interface. Finally, comparative leaching tests performed in sulphuric acid solutions revealed a significant influence of such media on the chemical durability of the leached pellets, leading to higher normalized dissolution rates for all the elements considered. On the basis of the results of chemical speciation, this difference was mainly explained in the light of higher complexion constants by sulfate ions compared to nitrate, chloride and phosphate.

Characterization of the Fishing Lines in Titiwai (=Arachnocampa luminosa Skuse, 1890) from New Zealand and Australia

PubMed Central

Merritt, David J.; Chandler, Peter; Stringer, Ian; Marchetti-Deschmann, Martina; McNaughton, Andrew; Cyran, Norbert; Thiel, Karsten; Noeske, Michael; Grunwald, Ingo

2016-01-01

Animals use adhesive secretions in a plethora of ways, either for attachment, egg anchorage, mating or as either active or passive defence. The most interesting function, however, is the use of adhesive threads to capture prey, as the bonding must be performed within milliseconds and under unsuitable conditions (movement of prey, variable environmental conditions, unfavourable attack angle, etc.) to be nonetheless successful. In the following study a detailed characterization of the prey capture system of the world-renowned glowworm group Arachnocampa from the macroscopic to the ultrastructural level is performed. The data reveal that the adhesive droplets consist mostly of water and display hygroscopic properties at varying humidity levels. The droplet core of Arachnocampa luminosa includes a certain amount of the elements sodium, sulphur and potassium (beside carbon, oxygen and nitrogen), while a different element composition is found in the two related species A. richardsae and A. tasmaniensis. Evidence for lipids, carbohydrates and proteins was negative on the histochemical level, however X-ray photoelectron spectroscopy confirm the presence of peptides within the droplet content. Different to earlier assumptions, the present study indicates that rather than oxalic acid, urea or uric acid are present in the adhesive droplets, presumably originating from the gut. Comparing the capture system in Arachnocampa with those of orb-spiders, large differences appear not only regarding the silky threads, but also, in the composition, hygroscopic properties and size of the mucous droplets. PMID:27973586

Assessment of mobility and bioavailability of mercury compounds in sewage sludge and composts.

PubMed

Janowska, Beata; Szymański, Kazimierz; Sidełko, Robert; Siebielska, Izabela; Walendzik, Bartosz

2017-07-01

Content of heavy metals, including mercury, determines the method of management and disposal of sewage sludge. Excessive concentration of mercury in composts used as organic fertilizer may lead to accumulation of this element in soil and plant material. Fractionation of mercury in sewage sludge and composts provides a better understanding of the extent of mobility and bioavailability of the different mercury species and helps in more informed decision making on the application of sludge for agricultural purposes. The experimental setup comprises the composing process of the sewage sludge containing 13.1mgkg -1 of the total mercury, performed in static reactors with forced aeration. In order to evaluate the bioavailability of mercury, its fractionation was performed in sewage sludge and composts during the process. An analytical procedure based on four-stage sequential extraction was applied to determine the mercury content in the ion exchange (water soluble and exchangeable Hg), base soluble (Hg bound to humic and fulvic acid), acid soluble (Hg bound to Fe/Mn oxides and carbonates) and oxidizable (Hg bound to organic matter and sulphide) fractions. The results showed that from 50.09% to 64.55% of the total mercury was strongly bound to organo-sulphur and inorganic sulphide; that during composting, increase of concentrations of mercury compounds strongly bound with organic matter and sulphides; and that mercury content in the base soluble and oxidizable fractions was strongly correlated with concentration of dissolved organic carbon in those fractions. Copyright © 2017 Elsevier Inc. All rights reserved.

Lipid biomarkers in Holocene and glacial sediments from ancient Lake Ohrid (Macedonia, Albania)

NASA Astrophysics Data System (ADS)

Holtvoeth, J.; Vogel, H.; Wagner, B.; Wolff, G. A.

2010-11-01

Organic matter preserved in Lake Ohrid sediments originates from aquatic and terrestrial sources. Its variable composition reflects climate-controlled changes in the lake basin's hydrology and related organic matter export, i.e. changes in primary productivity, terrestrial plant matter input and soil erosion. Here, we present first results from lipid biomarker investigations of Lake Ohrid sediments from two near-shore settings: site Lz1120 near the southern shore, with low-lying lands nearby and probably influenced by river discharge, and site Co1202 which is close to the steep eastern slopes. Variable proportions of terrestrial n-alkanoic acids and n-alkanols as well as compositional changes of ω-hydroxy acids document differences in soil organic matter supply between the sites and during different climate stages (glacial, Holocene, 8.2 ka cooling event). Changes in the vegetation cover are suggested by changes in the dominant chain length of terrestrial n-alkanols. Effective microbial degradation of labile organic matter and in situ contribution of organic matter derived from the microbes themselves are both evident in the sediments. We found evidence for anoxic conditions within the photic zone by detecting epicholestanol and tetrahymanol from sulphur-oxidising phototrophic bacteria and bacterivorous ciliates and for the influence of a settled human community from the occurrence of coprostanol, a biomarker for human and animal faeces (pigs, sheep, goats), in an early Holocene sample. This study illustrates the potential of lipid biomarkers for future environmental reconstructions using one of Europe's oldest continental climate archives, Lake Ohrid.

Studies on the effects of air pollution on limestone degradation in Great Britain

NASA Astrophysics Data System (ADS)

Webb, A. H.; Bawden, R. J.; Busby, A. K.; Hopkins, J. N.

The CEGB and the Cathedrals Advisory Commission for England formed a Joint Working Party in 1985 to promote a research programme aimed at improving the understanding of the relationships between stone decay, atmospheric pollution and other factors. The programme has included exposure of limestone samples at York Minster and eight other sites in England and Scotland selected to give a mix of urban, marine and rural locations. All of the sites have comprehensive air pollution and meteorological monitoring and measurement of rainfall chemistry. At two sites samples have been fumigated with controlled levels of sulphur dioxide. Over all sites, there was a significant trend to increased weight loss with increase in average sulphur dioxide concentration, but a negative trend with total nitrogen oxides and with nitrogen dioxide. For sample exposures longer than 200 days, the sulphur dioxide dependence at the inland Liphook fumigation site was about half that found near the coast at Littlehampton. There was no significant trend to increase weight loss with total rainfall amount for the complete data set, but the analysis was dominated by the very wet Scottish site, which experienced the lowest average concentrations of air pollutants. A theoretical model for the chemical dissolution of rainwashed limestone has been derived from consideration of the ion and mass balances between the incident rain water and run-off water. The model has been fitted to the measured loss rates from the stonework field trials. With the exception of the very wet Scottish site, the difference between the stone loss rate, calculated from the model, and the mean measured loss rate for any particular exposure was generally smaller than the variation between the triplicate samples. Variation in the dry deposition velocity between sites and exposure periods does not appear to have been a very significant factor, and no residual effect due to the concentrations of nitrogen oxides was found. The natural solubility of limestone in water was the dominant term in describing the stone loss, and neutralization of the rainfall acidity the least significant. The volume of the intercepted rainfall and the variation in the pH of the run-off water with rainfall intensity have been identified as the two most significant terms which require more precise quantification. The data from the inland fumigation site used in the model predict a stone loss due to sulphur dioxide in the air of less than 1 μm yr -1 surface recession per ppb SO 2.

30 CFR 250.1602 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... development and production of elemental sulphur. Sulphur operations also include activities conducted for... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations..., development, and production operations under an OCS sulphur lease. Sulphur operations include all activities...

Synthesis of high-purity precipitated calcium carbonate during the process of recovery of elemental sulphur from gypsum waste.

PubMed

de Beer, M; Doucet, F J; Maree, J P; Liebenberg, L

2015-12-01

We recently showed that the production of elemental sulphur and calcium carbonate (CaCO3) from gypsum waste by thermally reducing the waste into calcium sulphide (CaS) followed by its direct aqueous carbonation yielded low-grade carbonate products (i.e. <90 mass% as CaCO3). In this study, we used the insight gained from our previous work and developed an indirect aqueous CaS carbonation process for the production of high-grade CaCO3 (i.e. >99 mass% as CaCO3) or precipitated calcium carbonate (PCC). The process used an acid gas (H2S) to improve the aqueous dissolution of CaS, which is otherwise poorly soluble. The carbonate product was primarily calcite (99.5%) with traces of quartz (0.5%). Calcite was the only CaCO3 polymorph obtained; no vaterite or aragonite was detected. The product was made up of micron-size particles, which were further characterised by XRD, TGA, SEM, BET and true density. Results showed that about 0.37 ton of high-grade PCC can be produced from 1.0 ton of gypsum waste, and generates about 0.19 ton of residue, a reduction of 80% from original waste gypsum mass to mass of residue that needs to be discarded off. The use of gypsum waste as primary material in replacement of mined limestone for the production of PPC could alleviate waste disposal problems, along with converting significant volumes of waste materials into marketable commodities. Copyright © 2015 Elsevier Ltd. All rights reserved.

Changes in metal speciation and pH in olive processing waste and sulphur-treated contaminated soil.

PubMed

de la Fuente, C; Clemente, R; Bernal, M P

2008-06-01

Degradation of organic matter from olive mill waste and changes in the heavy metal fractionation of a metal-contaminated calcareous soil were studied in a laboratory experiment, in which the olive mill waste was mixed with the soil and then incubated under aerobic conditions. The soil was calcareous (15% CaCO(3)) with high Zn and Pb concentrations (2058 and 2947 mg kg(-1), respectively). The organic amendment was applied at a rate equivalent to 20 g kg(-1) soil, and unamended soil was run as a control. To discern if changes in metal solubility were due to the acidic character of the waste, elemental sulphur was applied to soil as a non-organic acidifying material. The S(0) rates used were 3.14, 4.71 and 6.28 g kg(-1). The mineralisation of total organic-C (TOC) from the waste reached 14.8% of the original TOC concentration after 56 days of incubation. The CO(2)-C produced from S(0)-treated soils showed the carbonate destruction by the H(2)SO(4) formed through S(0) oxidation. The organic waste increased EDTA-extractable Zn and Pb concentrations and CaCl(2)-extractable Mn levels in soil after two days of incubation. The changes in metal availability with time indicated that the oxidation of phenols from the waste reduced Mn (IV) oxides, releasing Zn and Pb associated with this mineral phase. Organic waste addition did not decrease soil pH; the acidifying effect of S(0) did not change metal fractionation in the soil.

Effect of H bond removal and changes in the position of the iron-sulphur head domain on the spin-lattice relaxation properties of the [2Fe-2S](2+) Rieske cluster in cytochrome bc(1).

PubMed

Sarewicz, Marcin; Dutka, Małgorzata; Pietras, Rafał; Borek, Arkadiusz; Osyczka, Artur

2015-10-14

Here, comparative electron spin-lattice relaxation studies of the 2Fe-2S iron-sulphur (Fe-S) cluster embedded in a large membrane protein complex - cytochrome bc1 - are reported. Structural modifications of the local environment alone (mutations S158A and Y160W removing specific H bonds between Fe-S and amino acid side chains) or in combination with changes in global protein conformation (mutations/inhibitors changing the position of the Fe-S binding domain within the protein complex) resulted in different redox potentials as well as g-, g-strain and the relaxation rates (T1(-1)) for the Fe-S cluster. The relaxation rates for T < 25 K were measured directly by inversion recovery, while for T > 60 K they were deduced from simulation of continuous wave EPR spectra of the cluster using a model that included anisotropy of Lorentzian broadening. In all cases, the relaxation rate involved contributions from direct, second-order Raman and Orbach processes, each dominating over different temperature ranges. The analysis of T1(-1) (T) over the range 5-120 K yielded the values of the Orbach energy (EOrb), Debye temperature θD and Raman process efficiency CRam for each variant of the protein. As the Orbach energy was generally higher for mutants S158A and Y160W, compared to wild-type protein (WT), it is suggested that H bond removal influences the geometry leading to increased strength of antiferromagnetic coupling between two Fe ions of the cluster. While θD was similar for all variants (∼107 K), the efficiency of the Raman process generally depends on the spin-orbit coupling that is lower for S158A and Y160W mutants, when compared to the WT. However, in several cases CRam did not only correlate with spin-orbit coupling but was also influenced by other factors - possibly the modification of protein rigidity and therefore the vibrational modes around the Fe-S cluster that change upon the movement of the iron-sulphur head domain.

Iron catalysis at the origin of life.

PubMed

Camprubi, Eloi; Jordan, Sean F; Vasiliadou, Rafaela; Lane, Nick

2017-06-01

Iron-sulphur proteins are ancient and drive fundamental processes in cells, notably electron transfer and CO 2 fixation. Iron-sulphur minerals with equivalent structures could have played a key role in the origin of life. However, the 'iron-sulphur world' hypothesis has had a mixed reception, with questions raised especially about the feasibility of a pyrites-pulled reverse Krebs cycle. Phylogenetics suggests that the earliest cells drove carbon and energy metabolism via the acetyl CoA pathway, which is also replete in Fe(Ni)S proteins. Deep differences between bacteria and archaea in this pathway obscure the ancestral state. These differences make sense if early cells depended on natural proton gradients in alkaline hydrothermal vents. If so, the acetyl CoA pathway diverged with the origins of active ion pumping, and ancestral CO 2 fixation might have been equivalent to methanogens, which depend on a membrane-bound NiFe hydrogenase, energy converting hydrogenase. This uses the proton-motive force to reduce ferredoxin, thence CO 2 . The mechanism suggests that pH could modulate reduction potential at the active site of the enzyme, facilitating the difficult reduction of CO 2 by H 2 . This mechanism could be generalised under abiotic conditions so that steep pH differences across semi-conducting Fe(Ni)S barriers drives not just the first steps of CO 2 fixation to C1 and C2 organics such as CO, CH 3 SH and CH 3 COSH, but a series of similar carbonylation and hydrogenation reactions to form longer chain carboxylic acids such as pyruvate, oxaloacetate and α-ketoglutarate, as in the incomplete reverse Krebs cycle found in methanogens. We suggest that the closure of a complete reverse Krebs cycle, by regenerating acetyl CoA directly, displaced the acetyl CoA pathway from many modern groups. A later reliance on acetyl CoA and ATP eliminated the need for the proton-motive force to drive most steps of the reverse Krebs cycle. © 2017 IUBMB Life, 69(6):373-381, 2017. © 2017 The Authors IUBMB Life published by Wiley Periodicals, Inc. on behalf of International Union of Biochemistry and Molecular Biology.

Sensitivity of high-spectral resolution and broadband thermal infrared nadir instruments to the chemical and microphysical properties of secondary sulfate aerosols in the upper-troposphere/lower-stratosphere

NASA Astrophysics Data System (ADS)

Sellitto, Pasquale; Legras, Bernard

2016-04-01

The observation of upper-tropospheric/lower-stratospheric (UTLS) secondary sulfate aerosols (SSA) and their chemical and microphysical properties from satellite nadir observations (with better spatial resolution than limb observations) is a fundamental tool to better understand their formation and evolution processes and then to estimate their impact on UTLS chemistry, and on regional and global radiative balance. Thermal infrared (TIR) observations are sensitive to the chemical composition of the aerosols due to the strong spectral variations of the imaginary part of the refractive index in this band and, correspondingly, of the absorption, as a function of the composition Then, these observations are, in principle, well adapted to detect and characterize UTLS SSA. Unfortunately, the exploitation of nadir TIR observations for sulfate aerosol layer monitoring is today very limited. Here we present a study aimed at the evaluation of the sensitivity of TIR satellite nadir observations to the chemical composition and the size distribution of idealised UTLS SSA layers. The sulfate aerosol particles are assumed as binary systems of sulfuric acid/water solution droplets, with varying sulphuric acid mixing ratios. The extinction properties of the SSA, for different sulfuric acid mixing ratios and temperatures, are systematically analysed. The extinction coefficients are derived by means of a Mie code, using refractive indices taken from the GEISA (Gestion et Étude des Informations Spectroscopiques Atmosphériques: Management and Study of Spectroscopic Information) spectroscopic database and log-normal size distributions with different effective radii and number concentrations. High-spectral resolution pseudo-observations are generated using forward radiative transfer calculations performed with the 4A (Automatized Atmospheric Absorption Atlas) radiative transfer model, to estimate the impact of the extinction of idealised aerosol layers, at typical UTLS conditions, on the brightness temperature (BT) spectra observed by satellite instruments. We isolated a marked and typical spectral signature of these aerosol layers between 700 and 1200 cm-1, due to the absorption bands of the sulfate and bisulfate ions and the undissociated sulfuric acid, with the main absorption peaks at 1170 and 905 cm-1 (sulfuric acid vibrational bands). The dependence of the residual aerosol spectral BT signature to the sulfuric acid mixing ratio, and effective number concentration and radius, as well as the role of interfering parameters like the ozone, sulfur dioxide, carbon dioxide and ash absorption, and temperature and water vapour profile uncertainties, are analysed and critically discussed. The information content (degrees of freedom and retrieval uncertainties) of synthetic satellite observations is estimated for different instrumental configurations. High spectral resolution (Infrared Atmospheric Sounding Interferometer (IASI)-like pseudo-observations) and broadband spectral features (Moderate Resolution Imaging Spectroradiometer (MODIS) and Spinning Enhanced Visible and InfraRed Imager (SEVIRI)-like pseudo-observations) approaches are proposed and discussed.

A comparison of the compositional differences between humic fractions isolated by the IHSS and exhaustive extraction procedures

NASA Astrophysics Data System (ADS)

Chang, R. R.; Mylotte, R.; Hayes, M. H. B.; Mclnerney, R.; Tzou, Y. M.

2014-03-01

Humic substances (HSs), consisting, on the basis of solubilities in aqueous acid and basic media, of humic acids (HAs), fulvic acids (FAs), and humin (Hu), are the major components of soil organic matter (SOM). Most studies of soil/natural organic matter (SOM/NOM) have been carried out on extracts of soils in dilute sodium hydroxide solutions, the solvent used to extract the Standards of the International Humic Substances Society (IHSS). However, Hu, the major component in the classical definition of HSs, is insoluble in aqueous base and is not isolated by the traditional IHSS method. Recently, a sequential exhaustive extraction (SEE) process has been shown to be capable of isolating and separating the major components of the classically defined HSs from the soils of the temperate and tropical regions. The SEE system was used in the present study to isolate the HA/FA and Hu fractions from a subtropical volcanic Taiwanese soil. Chemical and compositional properties of these extracts were then compared with similarly obtained isolates from soils from the different climatic regions. Increases in the aliphatic relative to aromatic carbon contents were observed for both the HA and FA fractions when the pH values of the extraction media were increased. HAs and FAs isolated using the SEE method have spectroscopic profiles similar to those from the IHSS isolate; however, the cumulative extraction efficiency (%) of the SEE method (65 %) for the volcanic soil was much higher than for the traditional IHSS method (33 %). When the residual volcanic soil, following extractions once, three, and eight times with 0.1 M NaOH were then extracted with dimethyl sulphoxide (DMSO) plus concentrated sulphuric acid (the final solvent in the SEE sequence) it was seen that the content of crystalline polymethylene hydrocarbon (33 ppm 13C-NMR resonance in the Hu (or DMSO/acid)) extract increased relative to the amorphous methylene (30 ppm). That highlights the difficulty in dissolving the more highly ordered hydrocarbon structures that would be expected to have closer associations with the mineral colloids. Although the SEE procedure isolated all of the HAs and FAs from the Yangmingshan soil, extractability of the Hu from the volcanic soil in the DMSO/acid solvent was low (21 %), and contrasted with the much higher yields from temperate and tropical regions. The decreased Hu extraction may arise from its associations with the extensive iron and aluminium hydroxide mineral colloids in the soil. The Hu from this sub-tropical soil was different from the Hus isolated from other soil types, indicating the need to isolate and characterise these recalcitrant organic material in order to understand the organic carbon components in soils in greater detail. Such results would indicate that more attention should be given to mineral colloids in soils, and to the organo/mineral associations that will have an important role in the stabilities of OM in the soil environment.

Preparation and characterization compatible pellets for immobilization of colloidal sulphur nanoparticles

NASA Astrophysics Data System (ADS)

Adlim, M.; Zarlaida, F.; Khaldun, I.; Dewi, R.; Jamilah, M.

2018-03-01

Mercury pollution in atmosphere is dominated by mercury vapour release from coal burning and gold-amalgam separation in gold mining. The initial steps in formulating a compatible mercury absorbent for mercury stabilization was fabrication of pellet supported colloidal sulphur. Sulphur is used to stabilize mercury vapour by formation of metacinnabar that has much lower toxicity. The sulphur reactivity toward mercury vapour can be enhanced by using colloidal sulphur nanoparticles immobilized on compatible pellets. Clay pellets would have heat resistance but in fact, they were less stable in aqueous solution although their stability increased with inclusion of rice husk ash and sawdust or pineapple leaf fibre in the composite. Pellets made of rice husk ash and polyvinyl acetate were stable in water at least for 24 hours. Sulphur from thiosulfate precursor that immobilized onto surface of pellet using chitosan as the stabilizer and the binding agent gave lower sulphur content compared to sulphur from other precursors (sulphur powder and sulphur-CS2). Sulphur from thiosulfate precursor was in form of colloid, has nanosize, and disperse particles on the surface of rice husk ash pellets. Sulphur immobilization methods affect on sulphur particles exposure on the pellet surface.

Electrochromic properties of polyaniline-coated fiber webs for tissue engineering applications.

PubMed

Beregoi, Mihaela; Busuioc, Cristina; Evanghelidis, Alexandru; Matei, Elena; Iordache, Florin; Radu, Mihaela; Dinischiotu, Anca; Enculescu, Ionut

2016-08-30

By combining the electrospinning method advantages (high surface-to-volume ratio, controlled morphology, varied composition and flexibility for the resulting structures) with the electrical activity of polyaniline, a new core-shell-type material with potential applications in the field of artificial muscles was synthesized. Thus, a poly(methylmethacrylate) solution was electrospun in optimized conditions to obtain randomly oriented polymer fiber webs. Further, a gold layer was sputtered on their surface in order to make them conductive and improve the mechanical properties. The metalized fiber webs were then covered with a PANI layer by in situ electrochemical polymerization starting from aniline and using sulphuric acid as oxidizing agent. By applying a small voltage on PANI-coated fiber webs in the presence of an electrolyte, the oxidation state of PANI changes, which is followed by the device color modification. The morphological, electrical and biological properties of the resulting multilayered material were also investigated. Copyright © 2015 Elsevier B.V. All rights reserved.

Influence of Mineral Dust On New Particle Formation and Growth: A Model Study of Heterogeneous Nucleation

NASA Astrophysics Data System (ADS)

Korhonen, H.; Kulmala, M.; Lauri, A.

Analyses of nucleation events have emphasized the importance of pre-existing par- ticles in new particle formation. When coarse mode aerosol is present, it typically dominates the condensation sink for trace gases and thus inhibits the onset of nucle- ation. A monodisperse aerosol dynamical box model is applied to investigate the effect of soluble coated mineral dust particles on new particle formation. The model in- cludes ternary H2SO4­H2O­NH3 nucleation, multicomponent condensation, coagu- lation and dry deposition. As the soluble coating can significantly change the ability of dust particles to serve as a condensation sink for condensable vapours, different mech- anisms of coating, including heterogeneous nucleation of sulphuric acid, are consid- ered. Preliminary results show that the presence of micron sized soluble coated dust par- ticles can even at relatively low concentrations prevent homogeneous nucleation or growth of nucleated particles to detectable size of 3 nm. Furthermore, critical conden- sation sinks obtained by model simulations correspond to measured sinks.

Role of relative humidity in processing and storage of seeds and assessment of variability in storage behaviour in Brassica spp. and Eruca sativa.

PubMed

Suma, A; Sreenivasan, Kalyani; Singh, A K; Radhamani, J

2013-01-01

The role of relative humidity (RH) while processing and storing seeds of Brassica spp. and Eruca sativa was investigated by creating different levels of relative humidity, namely, 75%, 50%, 32%, and 11% using different saturated salt solutions and 1% RH using concentrated sulphuric acid. The variability in seed storage behaviour of different species of Brassica was also evaluated. The samples were stored at 40 ± 2°C in sealed containers and various physiological parameters were assessed at different intervals up to three months. The seed viability and seedling vigour parameters were considerably reduced in all accessions at high relative humidity irrespective of the species. Storage at intermediate relative humidities caused minimal decline in viability. All the accessions performed better at relative humidity level of 32% maintaining seed moisture content of 3%. On analyzing the variability in storage behaviour, B. rapa and B. juncea were better performers than B. napus and Eruca sativa.

Development of volatile compounds during the manufacture of dry-cured "lacón," a Spanish traditional meat product.

PubMed

Purriños, Laura; Bermúdez, Roberto; Franco, Daniel; Carballo, Javier; Lorenzo, José M

2011-01-01

Volatile compounds were determined throughout the manufacture of dry-cured "lacón," a traditional dry-salted, and ripened meat product made in the north-west of Spain from the foreleg of the pig following a similar process to that of dry-cured ham. Volatiles were extracted by a purge-and-trap method and analyzed by gas chromatographic/mass spectrometry. One hundred and two volatile compounds were identified. In raw material, only 34 volatile compounds were found and at very low levels. The number of volatile compounds increased during processing. The substances identified belonged to several chemical classes: aldehydes (23), alcohols (9), ketones (15), hydrocarbons (37), esters (4), acids (3), furans (4), sulphur compounds (1), chloride compounds (1), and other compounds (4). Results indicated that the most abundant chemical family in flavor at the end of the manufacturing process was aldehydes, followed by hydrocarbons and ketones. Lipids were the most important precursor of flavor compounds of dry-cured "lacón."

A comparative study on cellulose nanocrystals extracted from bleached cotton and flax and used for casting films with glycerol and sorbitol plasticisers.

PubMed

Csiszár, Emilia; Nagy, Sebestyén

2017-10-15

Cellulose nanocrystals (CNCs) were released from bleached cotton and flax by a sulphuric acid hydrolysis with about 40 and 34% yield, respectively. The rod-like cotton-CNC particles were slightly longer and wider and had a less pronounced aggregation ability in aqueous suspension than the flax-CNC ones. Films were cast from the CNC suspensions with sorbitol and glycerol plasticisers. The concept behind this research was to explore how the plasticisers - with similar structure but different molecular weight - and their concentrations affect the perceptible and measured properties of CNC films. Results revealed that the type of plasticiser determined the morphology and the optical and tensile properties of films. The best quality CNC film with an averaged thickness of 50μm was obtained with 20% sorbitol from cotton-CNC. It was proved that behaviour of sorbitol and glycerol plasticisers in CNC films was very similar to that reported previously for starch films. Copyright © 2017 Elsevier Ltd. All rights reserved.

When color fails: illicit blue tablets containing anabolic androgen steroids.

PubMed

Favretto, Donata; Castagna, Franca; Maietti, Sergio; Boscolo-Berto, Rafael; Ferrara, Santo Davide

2013-09-01

The necessity of specific, confirmatory tests in the identification of seized illicit products was highlighted by the analysis of eighteen heart shaped, blue tablets confiscated by Police at a street control in the North East of Italy. The tablets responded as amphetamines to a preliminary color test (Marquis); a subsequent, confirmatory assay by gas chromatography-mass spectrometry revealed the presence of two anabolic androgen steroids (AAS), methandienone and methyltestosterone, in concentration of 1.7 and 1.5mg respectively per tablet; no trace of amphetamine-like or nitrogen containing compounds was found. The observed orange coloration was due to the reaction of concentrated sulphuric acid, contained in the Marquis reagent, with the Δ(4) C-3 keto group of steroids. The two AAS, banned under the world antidoping code, are not considered as psychoactive drugs of abuse in most countries, although their trafficking may entangle severe public health concerns. Copyright © 2013 Elsevier B.V. All rights reserved.

A basalt trigger for the 1991 eruptions of Pinatubo volcano?

USGS Publications Warehouse

Pallister, J.S.; Hoblitt, R.P.; Reyes, A.G.

1992-01-01

THE eruptive products of calc-alkaline volcanos often show evidence for the mixing of basaltic and acid magmas before eruption (see, for example, refs 1, 2). These observations have led to the suggestion3 that the injection of basaltic magma into the base of a magma chamber (or the catastrophic overturn of a stably stratified chamber containing basaltic magma at its base) might trigger an eruption. Here we report evidence for the mixing of basaltic and dacitic magmas shortly before the paroxysmal eruptions of Pinatubo volcano on 15 June 1991. Andesitic scoriae erupted on 12 June contain minerals and glass with disequilibrium compositions, and are considerably more mafic than the dacitic pumices erupted on 15 June. Differences in crystal abundance and glass composition among the pumices may arise from pre-heating of the dacite magma by the underlying basaltic liquid before mixing. Degassing of this basaltic magma may also have contributed to the climatologically important sulphur dioxide emissions that accompanied the Pinatubo eruptions.

Evaluation of phase separator number in hydrodesulfurization (HDS) unit

NASA Astrophysics Data System (ADS)

Jayanti, A. D.; Indarto, A.

2016-11-01

The removal process of acid gases such as H2S in natural gas processing industry is required in order to meet sales gas specification. Hydrodesulfurization (HDS)is one of the processes in the refinery that is dedicated to reduce sulphur.InHDS unit, phase separator plays important role to remove H2S from hydrocarbons, operated at a certain pressure and temperature. Optimization of the number of separator performed on the system is then evaluated to understand the performance and economics. From the evaluation, it shows that all systems were able to meet the specifications of H2S in the desired product. However, one separator system resulted the highest capital and operational costs. The process of H2S removal with two separator systems showed the best performance in terms of both energy efficiency with the lowest capital and operating cost. The two separator system is then recommended as a reference in the HDS unit to process the removal of H2S from natural gas.

Integrating Environmental Genomics and Biogeochemical Models: a Gene-centric Approach

NASA Astrophysics Data System (ADS)

Reed, D. C.; Algar, C. K.; Huber, J. A.; Dick, G.

2013-12-01

Rapid advances in molecular microbial ecology have yielded an unprecedented amount of data about the evolutionary relationships and functional traits of microbial communities that regulate global geochemical cycles. Biogeochemical models, however, are trailing in the wake of the environmental genomics revolution and such models rarely incorporate explicit representations of bacteria and archaea, nor are they compatible with nucleic acid or protein sequence data. Here, we present a functional gene-based framework for describing microbial communities in biogeochemical models that uses genomics data and provides predictions that are readily testable using cutting-edge molecular tools. To demonstrate the approach in practice, nitrogen cycling in the Arabian Sea oxygen minimum zone (OMZ) was modelled to examine key questions about cryptic sulphur cycling and dinitrogen production pathways in OMZs. By directly linking geochemical dynamics to the genetic composition of microbial communities, the method provides mechanistic insights into patterns and biogeochemical consequences of marine microbes. Such an approach is critical for informing our understanding of the key role microbes play in modulating Earth's biogeochemistry.

An integrated fingerprinting and kinetic approach to accelerated shelf-life testing of chemical changes in thermally treated carrot puree.

PubMed

Kebede, Biniam T; Grauwet, Tara; Magpusao, Johannes; Palmers, Stijn; Michiels, Chris; Hendrickx, Marc; Loey, Ann Van

2015-07-15

To have a better understanding of chemical reactions during shelf-life, an integrated analytical and engineering toolbox: "fingerprinting-kinetics" was used. As a case study, a thermally sterilised carrot puree was selected. Sterilised purees were stored at four storage temperatures as a function of time. Fingerprinting enabled selection of volatiles clearly changing during shelf-life. Only these volatiles were identified and studied further. Next, kinetic modelling was performed to investigate the suitability of these volatiles as quality indices (markers) for accelerated shelf-life testing (ASLT). Fingerprinting enabled selection of terpenoids, phenylpropanoids, fatty acid derivatives, Strecker aldehydes and sulphur compounds as volatiles clearly changing during shelf-life. The amount of Strecker aldehydes increased during storage, whereas the rest of the volatiles decreased. Out of the volatiles, based on the applied kinetic modelling, myristicin, α-terpinolene, β-pinene, α-terpineol and octanal were identified as potential markers for ASLT. Copyright © 2015 Elsevier Ltd. All rights reserved.

Flow injection chemiluminescent determination of tetracycline using a tris(2,2'-bipyridine)ruthenium(II)-cerium(IV) sulphate system.

PubMed

Guo, Liangqia; Xie, Zenghong; Lin, Xucong; Liu, Xiaohua; Zhang, Weilin; Chen, Guonan

2004-01-01

A flow-injection chemiluminescence method for the determination of tetracycline was developed. The method is based on an enhancement by tetracycline of the chemiluminescence light emission of tris(2,2'-bipyridine)ruthenium(II). In sulphuric acid medium, the chemiluminescence is generated by the continuous oxidation of tris(2,2'-bipyridine)ruthenium(II) by cerium (IV) sulphate. The light-emission intensity is greatly enhanced in the presence of tetracycline. Under the optimum conditions, the calibration curve is linear over the range 3.75 x 10(-8) g/mL-1.5 x 10(-5) g/mL for tetracycline with the linear equation: deltaINT = 205.898 x C - 20.442 (R2 = 0.9974). The detection limit is 3.27 x 10(-8) g/mL. The proposed method was also successfully used to determine tetracycline in pharmaceutical formulation (mean recovery of tetracycline, 100.7%). Copyright 2004 John Wiley & Sons, Ltd.