Science.gov

Sample records for acidic cation exchange

  1. Simultaneous ion-exclusion/cation-exchange chromatography of anions and cations in acid rain waters on a weakly acidic cation-exchange resin by elution with sulfosalicylic acid.

    PubMed

    Tanaka, K; Ohta, K; Haddad, P R; Fritz, J S; Miyanaga, D A; Hu, W; Hasebe, K

    2000-07-01

    A simple, selective, and sensitive method for the simultaneous determination of anions (sulfate, nitrate, and chloride) and cations (sodium, ammonium, potassium, magnesium, and calcium) in acid rain waters was developed using ion-exclusion/ cation-exchange chromatography with conductimetric detection. A weakly acidic cation-exchange resin column (Tosho TSKgel OA-PAK-A) and a sulfosalicylic acid-methanol-water eluent was used. With a mobile phase comprising 1.25 mM sulfosalicylic acid in methanol-water (7.5:92.5) at 1.2 ml/min, simultaneous separation and detection of the above anions and cations was achieved in about 30 min. Linear calibration plots of peak area versus concentration were obtained over the concentration ranges 0-1.0 mM for anions (R=0.9991) and 0-0.5 mM for cations (R=0.9994). Detection limits calculated at S/N=3 ranged from 4.2 to 14.8 ppb for the anions and from 2.4 to 12.1 ppb for the cations. The reproducibility of retention times was 0.14-0.15% relative standard deviation (RSD) for anions and 0.18-0.31% for cations, and reproducibility of chromatographic peak areas was 1.22-1.75% RSD for anions and 1.81-2.10% for cations. The method was applied successfully to the simultaneous determination of anions and cations in aerosols transported from mainland China to central Japan, as determined by a meteorological satellite data analyzer.

  2. Separation of certain carboxylic acids utilizing cation exchange membranes

    DOEpatents

    Chum, Helena L.; Sopher, David W.

    1984-01-01

    A method of substantially separating monofunctional lower carboxylic acids from a liquid mixture containing the acids wherein the pH of the mixture is adjusted to a value in the range of from about 1 to about 5 to form protonated acids. The mixture is heated to an elevated temperature not greater than about 100.degree. C. and brought in contact with one side of a perfluorinated cation exchange membrane having sulfonate or carboxylate groups or mixtures thereof with the mixture containing the protonated acids. A pressure gradient can be established across the membrane with the mixture being under higher pressure, so that protonated monofunctional lower carboxylic acids pass through the membrane at a substantially faster rate than the remainder of the mixture thereby substantially separating the acids from the mixture.

  3. Separation of certain carboxylic acids utilizing cation exchange membranes

    DOEpatents

    Chum, H.L.; Sopher, D.W.

    1983-05-09

    A method of substantially separating monofunctional lower carboxylic acids from a liquid mixture containing the acids wherein the pH of the mixture is adjusted to a value in the range of from about 1 to about 5 to form protonated acids. The mixture is heated to an elevated temperature not greater than about 100/sup 0/C and brought in contact with one side of a perfluorinated cation exchange membrane having sulfonate or carboxylate groups or mixtures thereof with the mixture containing the protonated acids. A pressure gradient can be established across the membrane with the mixture being under higher pressure, so that protonated monofunctional lower carboxylic acids pass through the membrane at a substantially faster rate than the remainder of the mixture thereby substantially separating the acids from the mixture.

  4. High-performance ion-exclusion/cation-exchange chromatography of anions and cations in acid rain waters on a weakly acidic cation-exchange resin.

    PubMed

    Tanaka, K; Ohta, K; Haddad, P R; Fritz, J S; Miyanaga, A; Hu, W; Hasebe, K; Lee, K P; Sarzanini, C

    2001-06-22

    A new method for the simultaneous determination of anions (sulfate, nitrate, and chloride) and cations (sodium, ammonium, potassium, magnesium, and calcium) in acid rain waters was investigated using high-performance ion-exclusion/cation-exchange chromatography with conductimetric detection on a separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin in the hydrogen-form and an eluent comprising 1.5 mM sulfosalicylic acid-6 mM 18-crown-6 at pH 2.6, operated at 1.5 ml/min. Effective separation and highly sensitive conductimetric detection for the anions and the cations was achieved in about 14 min. Since the ionic balance (equivalents of anions/equivalents of cations) of acid rain waters of different pH (4.40-4.67) ranged from 0.97 to 0.94, evaluation of the water quality of acid rain was possible. This method was successfully applied to the simultaneous determination of the anions and the cations in acid rain transported from mainland China and North Korea to central Japan monitored by a meteorological satellite data analyzer.

  5. High-speed simultaneous ion-exclusion/cation-exchange chromatography of anions and cations on a weakly acidic cation-exchange resin column.

    PubMed

    Mori, Masanobu; Tanaka, Kazuhiko; Helaleh, Murad I H; Xu, Qun; Ikedo, Mikaru; Ogura, Yutaka; Sato, Shinji; Hu, Wenzhi; Hasebe, Kiyoshi; Haddad, Paul R

    2003-05-16

    The simultaneous ion-exclusion/cation-exchange separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin of 3 microm particle size was used to achieve the simultaneous high-speed separation of anions and cations (Cl(-), NO3(-), SO4(2-), Na(+), K(+), NH4(+), Ca(2+) and Mg(2+)) commonly found in environmental samples. The high-speed simultaneous separation is based on a combination of the ion-exclusion mechanism for the anions and the cation-exchange mechanism for cations. The complete separation of the anions and cations was achieved in 5 min by elution with 15 mM tartaric acid-2.5 mM 18-crown-6 at a flow-rate of 1.5 ml/min. Detection limits at S/N=3 ranged from 0.36 to 0.68 microM for anions and 0.63-0.99 microM for cations. This method has been applied to the simultaneous determination of anions and cations in several environmental waters with satisfactory results.

  6. Simultaneous ion-exclusion chromatography and cation-exchange chromatography of anions and cations in environmental water samples on a weakly acidic cation-exchange resin by elution with pyridine-2,6-dicarboxylic acid.

    PubMed

    Ding, M Y; Tanaka, K; Hu, W; Hasebe, K; Haddad, P R

    2001-05-01

    A non-suppressed conductivity detection ion chromatographic method using a weakly acidic cation-exchange column (Tosoh TSKgel OApak-A) was developed for the simultaneous separation and determination of common inorganic anions (Cl-, NO3- and SO4(2-)) and cations (Na+, NH4+, K+, Mg2+ and Ca2+). A satisfactory separation of these anions and cations on the weakly acidic cation-exchange column was achieved in 25 min by elution with a mixture of 1.6 mmol L-1 pyridine-2,6-dicarboxylic acid and 8.0 mmol L-1 18-crown-6 at flow rate of 1.0 mL min-1. On this weakly acidic cation-exchange resin, anions were retained by an ion-exclusion mechanism and cations by a cation-exchange mechanism. The linear range of the peak area calibration curves for all analytes were up to two orders of magnitude. The detection limits calculated at S/N = 3 ranged from 0.25 to 1.9 mumol L-1 for anions and cations. The ion-exclusion chromatography-cation-exchange chromatography method developed in this work was successfully applied to the simultaneous determination of major inorganic anions and cations in rainwater, tap water and snow water samples.

  7. Simultaneous determination of anions and cations by ion-exclusion chromatography-cation-exchange chromatography with tartaric acid/18-crown-6 as eluent.

    PubMed

    Kwon, S M; Lee, K P; Tanaka, K; Ohta, K

    1999-07-30

    Ion-exclusion chromatography-cation-exchange chromatography was developed for the simultaneous separation of common inorganic anions and cations (Cl-, NO3- and SO4(2-); Na+, NH4+, K+, Mg2+ and Ca2+) on a weakly acidic cation-exchange column by elution with weak acid. Generally, the resolution among these monovalent cations was only moderate, thereby hindering the determination of these analytes in natural-water samples. Therefore, 18-crown-6 was added to the eluent to improve the resolution. A good separation of these anions and cations on a weakly acidic cation-exchange column was achieved in 30 min by elution with 5 mM tartaric acid/6 mM 18-crown-6/methanol-water (7.5:92.5). The ion-exclusion chromatography-cation-exchange chromatography method developed here was successfully applied to the separation of major anions and cations in an environmental water sample.

  8. A method for the production of weakly acidic cation exchange resins

    NASA Astrophysics Data System (ADS)

    Heller, H.; Werner, F.; Mitschker, A.; Diehl, H. V.; Schaefer, A.

    1991-12-01

    The invention relates to a nonpolluting method for the production of weakly acidic cation exchange resins by saponification of cross-linked acrylonitrile bead polymers, with an alkaline saponification agent at elevated temperature, according to which method the bead polymer and alkaline saponification agent are jointly added only at elevated temperature.

  9. Tree species affect cation exchange capacity (CEC) and cation binding properties of organic matter in acid forest soils.

    PubMed

    Gruba, Piotr; Mulder, Jan

    2015-04-01

    Soil organic matter (SOM) in forest soil is of major importance for cation binding and acid buffering, but its characteristics may differ among soils under different tree species. We investigated acidity, cation exchange properties and Al bonding to SOM in stands of Scots pine, pedunculate oak, Norway spruce, European beech and common hornbeam in southern Poland. The content of total carbon (Ct) was by far the major contributor to total cation exchange capacity (CECt) even in loamy soils and a strong relationship between Ct and CECt was found. The slope of the regression of CECt to Ct increased in the order hornbeam≈oakacid pH range was smallest for hornbeam and oak, and largest for spruce and pine soils. This was supported by the apparent dissociation constant (pKapp) values of SOM, which were largest in soils under oak. The maximum values of Al saturation were similar between the stands. However, maximum Al bonding to SOM occurred at higher pH values in soils under pine and spruce than under oak. Therefore, at any value in the acid pH range, the SOM in pine soil has less Al complexed and more adsorbed H+ than SOM from oak soils. Such differences in Al and H bonding are not only important for pH buffering and metal solubility controls, but also for stabilization of SOM via saturation of functional groups by Al and H.

  10. Tree species affect cation exchange capacity (CEC) and cation binding properties of organic matter in acid forest soils.

    PubMed

    Gruba, Piotr; Mulder, Jan

    2015-04-01

    Soil organic matter (SOM) in forest soil is of major importance for cation binding and acid buffering, but its characteristics may differ among soils under different tree species. We investigated acidity, cation exchange properties and Al bonding to SOM in stands of Scots pine, pedunculate oak, Norway spruce, European beech and common hornbeam in southern Poland. The content of total carbon (Ct) was by far the major contributor to total cation exchange capacity (CECt) even in loamy soils and a strong relationship between Ct and CECt was found. The slope of the regression of CECt to Ct increased in the order hornbeam≈oakacid pH range was smallest for hornbeam and oak, and largest for spruce and pine soils. This was supported by the apparent dissociation constant (pKapp) values of SOM, which were largest in soils under oak. The maximum values of Al saturation were similar between the stands. However, maximum Al bonding to SOM occurred at higher pH values in soils under pine and spruce than under oak. Therefore, at any value in the acid pH range, the SOM in pine soil has less Al complexed and more adsorbed H+ than SOM from oak soils. Such differences in Al and H bonding are not only important for pH buffering and metal solubility controls, but also for stabilization of SOM via saturation of functional groups by Al and H. PMID:25596350

  11. Some investigations on the radiation stability of a strongly acidic cation exchange resin

    NASA Astrophysics Data System (ADS)

    Dessouki, A. M.; Zahran, A. H.; Rabie, A. M.; Amer, S. I.

    The radiation-chemical stability of Merck Cation Exchanger I, a strongly acidic sulphonated cation exchanger of the polymerization type based on styrene-divinylbenze (DVB) copolymers was investigated. The radiation stability of the resin was assessed from the change in exchange capacity, loss in weight, change in swelling behaviour and formation of new exchange groups. The loss in capacity was 44 and 32% for resin specimens in the H +-form irradiated to 1000 Mrad in air and in vacuum, respectively. The Na +-form of the exchanger showed high resistance to radiation and the loss in capacity did not exceed 7% at a dose of 1000 Mrad. The loss in capacity was accompanied by a loss in weight and a decrease in the degree of swelling of the irradiated resin. The formation of new functional groups of the carboxylic and phenolic types was confirmed. The amount of these group increases with the increase in the integral dose. The amount of sulphuric acid formed as a result of irradiating the resin in the dry and moist states was determined. An increase in the moisture content of the resin resulted in a marked decrease in its radiation stability.

  12. Synthesis, characterization and applications of a new cation exchanger tamarind sulphonic acid (TSA) resin.

    PubMed

    Singh, A V; Sharma, Naresh Kumar; Rathore, Abhay S

    2012-01-01

    A new composite cation exchanger, tamarind sulphonic acid (TSA) resin has been synthesized. The chemically modified TSA ion exchange resin has been used for the removal and preconcentration of Zn2+, Cd2+, Fe2+, Co2+ and Cu2+ ions in aqueous solution and effluent from the Laxmi steel plant in Jodhpur, India. This type of composite represents a new class of hybrid ion exchangers with good ion exchange capacity, stability, reproducibility and selectivity for toxic metal ions found in effluent from the steel industry. The characterization of the resin was carried out by determining the ion-exchange capacity, elemental analysis, pH titration, Fourier transform infrared spectra and thermal analysis. The distribution coefficients (K(d)) of toxic metal ions were determined in a reference aqueous solution and the steel plant effluent at different pH values; the absorbency of different metal ions on the TSA resin was studied for up to 10 cycles. The adsorption of different metal ions on TSA resin follows the order: Co2+ > Cu2+ > Zn2+ > Fe2+ > Cd2+. The ion exchange capacity of TSA resin is 2.87%. PMID:22629619

  13. Acid-rain monitoring in east Asia with a portable-type ion-exclusion-cation-exchange chromatographic analyzer.

    PubMed

    Tanaka, K; Ohta, K; Haddad, P R; Fritz, J S; Lee, K P; Hasebe, K; Ieuji, A; Miyanaga, A

    1999-07-30

    A monitoring system consisting of a portable-type conductimetric ion-exclusion-cation-exchange chromatographic (CEC) analyzer and a meteorological satellite data analyzer has been investigated for the evaluation of the effects of acid precipitation on natural and urban environments in East Asia. The portable ion-exclusion-CEC analyzer uses a polymethacrylate-based weakly acidic cation-exchange resin column in the H(+)-form and a weak-acid eluent (tartaric acid-methanol-water) and is applied for the simultaneous determination of anions (SO4(2)-, NO3-, and Cl-) and cations (Na+, NH4+, K+, Mg2+, and Ca2+) in precipitation transported from mainland China to central Japan, as mapped by the meteorological satellite data analyzer. Linear calibration graphs of peak area versus concentration for anions and cations were observed in the concentration range 0-1.0 mM for the anions and 0-0.5 mM for the cations. Detection limits at a signal-to-noise ratio of 3 were in the range 5.18-12.1 ppb for the anions and 6.58-16.5 ppb for the cations. The practical utility of this monitoring system is presented.

  14. Synthesis and properties of a cation exchange resin prepared by the pyrolysis of starch in the presence of phytic acid

    SciTech Connect

    Lehrfeld, J.

    1995-12-01

    A material having cation exchange and adsorption properties was prepared by the controlled pyrolysis of starch in the presence of a commercial phytic acid solution. Resins can be prepared with binding capacities of 0.7-5.7 meq/g. These resins also have the ability to remove atrazine from aqueous solutions.

  15. Continuous process of preparation of n-butyl(meth)acrylate by esterification of (meth)acrylic acid by butanol on thermostable sulfo-cation exchanger

    SciTech Connect

    Zheleznaya, L.L.; Karakhanov, R.A.; Lunin, A.F.; Magadov, R.S.; Meshcheryakov, S.V.; Mkrtychan, V.R.; Fomin, V.A.

    1987-11-10

    The authors propose an effective thermostable sulfo-cation exchanger based on polymers with a system of conjugated bonds, sulfopolyphenylene ketone (SPP) differing from the known cation exchangers by the high thermostability (up to 250/sup 0/C), and also having the effect of the stabilization of the double bond in unsaturated monomers. The combination of inhibiting and cation exchange properties makes it also possible to use these sulfo-cation exchangers in the processes of esterification of (meth)acrylic acids by alcohols without addition of special inhibitors. The SPP catalyst was tested in esterification processes of acrylic an methacrylic acid by butanol at a pilot plant.

  16. Kinetics and Thermodynamics of Reserpine Adsorption onto Strong Acidic Cationic Exchange Fiber

    PubMed Central

    Guo, Zhanjing; Liu, Xiongmin; Huang, Hongmiao

    2015-01-01

    The kinetics and thermodynamics of the adsorption process of reserpine adsorbed onto the strong acidic cationic exchange fiber (SACEF) were studied by batch adsorption experiments. The adsorption capacity strongly depended on pH values, and the optimum reserpine adsorption onto the SACEF occurred at pH = 5 of reserpine solution. With the increase of temperature and initial concentration, the adsorption capacity increased. The equilibrium was attained within 20 mins. The adsorption process could be better described by the pseudo-second-order model and the Freundlich isotherm model. The calculated activation energy Ea was 4.35 kJ/mol. And the thermodynamic parameters were: 4.97<ΔH<7.44 kJ/mol, -15.29<ΔG<-11.87 kJ/mol and 41.97<ΔS<47.35 J/mol·K. The thermodynamic parameters demonstrated that the adsorption was an endothermic, spontaneous and feasible process of physisorption within the temperature range between 283 K and 323 K and the initial concentration range between 100 mg/L and 300 mg/L. All the results showed that the SACEF had a good adsorption performance for the adsorption of reserpine from alcoholic solution. PMID:26422265

  17. Ion-exchange chromatography of mono- and divalent cations in natural waters on a weak-acid anion-exclusion column.

    PubMed

    Tanaka, K; Ohta, K; Haddad, P R; Fritz, J S

    1998-04-24

    Ion-exchange chromatography with indirect conductimetric detection for the simultaneous determination of mono- and divalent cations is investigated using an anion-exclusion chromatographic column packed with polymethacrylate-based weakly acidic cation-exchange resin in the H+ form (Tosoh TSKgel OA-PAK-A, 300 mm x 7.8 mm I.D.). An eluent comprising a strong acid, a weak organic acid, methanol and water is used. Using 0.75 mM sulfuric acid, 2 mM tartaric acid, 7.5% (v/v) methanol in water as eluent, the monovalent cations (Na+, NH4+, and K+) and divalent cations (Mg2+ and Ca2+) were separated simultaneously by a cation-exchange mechanism in about 25 min. The application of this method to the analysis of several natural waters including rain, river, lake, underground and forest soil waters for estimating acid rain effects on the natural and urban environments is presented.

  18. Simultaneous determination of cation exchange capacity and surface area of acid activated bentonite powders by methylene blue sorption

    NASA Astrophysics Data System (ADS)

    Yener, Nilgün; Biçer, Cengiz; Önal, Müşerref; Sarıkaya, Yüksel

    2012-01-01

    To distinguish the ion exchanged and physically adsorbed methylene blue cations (MB+) on ionic surfaces, acid activated bentonite samples were used as porous adsorbents. A natural calcium bentonite (CaB) sample from Enez/Edirne, Turkey, was acid activated at 90 °C for 16 h with various HCl/CaB ratios. The irreversible exchange and physical adsorption of MB+ cations on the ionic solids have simultaneously occurred. The ion exchanged (mex) and physically adsorbed (mad) MB+ contents were obtained as the values of sorption capacity at c = 0 and the increase to a plateaus of adsorption isotherms, respectively. The mad value was taken to be monolayer adsorption capacity. Cation exchange capacity (CEC) and specific surface area (SMB) for each sample were calculated from the mex and mad values, respectively. Also, the BET specific surface areas (SBET) and pore size distribution were determined from low temperature nitrogen adsorption/desorption data. A linear correlation between the SMB and SBET values was found.

  19. Preparation of poly(glycidylmethacrylate-divinylbenzene) weak acid cation exchange stationary phases with succinic anhydride, phthalic anhydride, and maleic anhydride for ion chromatography.

    PubMed

    Liu, Junwei; Wang, Yong; Wu, Shuchao; Zhang, Peimin; Zhu, Yan

    2016-08-01

    In this work, poly(glycidylmethacrylate-divinylbenzene) microspheres were prepared and applied for the preparation of weak acid cation exchange stationary phases. Succinic anhydride, phthalic anhydride, and maleic anhydride were selected as carboxylation reagents to prepare three weak acid cation exchangers by direct chemical derivatization reaction without solvent or catalyst. The diameters and dispersity of the microspheres were characterized by scanning electron microscopy; the amount of accessible epoxy groups and mechanical stability were also measured. The weak acid cation exchangers were characterized by Fourier transform infrared spectroscopy; the content of carboxyl groups was measured by traditional acid base titration method. The chromatographic properties were characterized and compared by separating alkali, alkaline earth metal ions and ammonium and polar amines. The separation properties enhanced in the order of succinic anhydride, phthalic anhydride, and maleic anhydride modified poly(glycidylmethacrylate-divinylbenzene) cation exchangers.

  20. Preparation of poly(glycidylmethacrylate-divinylbenzene) weak acid cation exchange stationary phases with succinic anhydride, phthalic anhydride, and maleic anhydride for ion chromatography.

    PubMed

    Liu, Junwei; Wang, Yong; Wu, Shuchao; Zhang, Peimin; Zhu, Yan

    2016-08-01

    In this work, poly(glycidylmethacrylate-divinylbenzene) microspheres were prepared and applied for the preparation of weak acid cation exchange stationary phases. Succinic anhydride, phthalic anhydride, and maleic anhydride were selected as carboxylation reagents to prepare three weak acid cation exchangers by direct chemical derivatization reaction without solvent or catalyst. The diameters and dispersity of the microspheres were characterized by scanning electron microscopy; the amount of accessible epoxy groups and mechanical stability were also measured. The weak acid cation exchangers were characterized by Fourier transform infrared spectroscopy; the content of carboxyl groups was measured by traditional acid base titration method. The chromatographic properties were characterized and compared by separating alkali, alkaline earth metal ions and ammonium and polar amines. The separation properties enhanced in the order of succinic anhydride, phthalic anhydride, and maleic anhydride modified poly(glycidylmethacrylate-divinylbenzene) cation exchangers. PMID:27288092

  1. Simple preparation of solid-phase microextraction fiber with cation exchange capacities using poly(butadiene-maleic acid).

    PubMed

    Zhu, Yingli; Shen, Guobin; Zhang, Feifang; Yang, Bingcheng

    2013-01-01

    A simply way was proposed to prepare solid-phase microextraction (SPME) fiber with cation-exchange functional groups by the thermally initiated radical polymerization of poly(butadiene-maleic acid) (PBMA) copolymer onto a silica capillary. The capacity of the fiber coating could be easily controlled by fabricating successive layers of PBMA. The performance of the fiber combined with ion chromatography was evaluated by choosing Mg(2+) and Ca(2+) as model analytes; ∼13 and ∼51-fold enrichment factors for Mg(2+) and Ca(2+) were obtained, respectively. PMID:24107568

  2. Preparation and applications of weak acid cation exchanger based on monodisperse poly(ethylvinylbenzene-co-divinylbezene) beads.

    PubMed

    Zhu, Yan; Yongxin, Chen; Mingli, Ye; Fritz, James S

    2005-08-26

    New technology is reported here for the synthesis of an effective weak acid-cation exchanger for ion chromatography. Monodisperse macroporous poly(ethylvinylbenzene-co-divinylbezene) (PEVB-DVB) beads of 5 microm diameter were prepared by a two-step swelling and polymerization method. Then carboxyl groups were introduced by polymerization of maleic anhydride with unreacted vinyl groups on the resin beads, followed by hydrolysis of the maleic anhydride groups. A column packed with the carboxylate beads was used to separate alkali and alkaline earth metal ions in a single isocratic run. Separations were found to be better than those with similar resin particles that are simply coated with maleic acid. The columns containing the new particles were 100% compatible with solvents commonly used for HPLC. Additionally, the prepared column was stable and could be used for a long time in a wide range of pH. The column gave good resolution, low detection limits and good repeatability for the separation of common cations. Satisfactory results were also obtained for separations of organic amines and of common cations in rainwater.

  3. On-line cation exchange for suppression of adduct formation in negative-ion electrospray mass spectrometry of nucleic acids.

    PubMed

    Huber, C G; Buchmeiser, M R

    1998-12-15

    One major difficulty in the analysis of nucleic acids by electrospray mass spectrometry is represented by the affinity of the polyanionic sugar-phosphate backbone for nonvolatile cations, especially ubiquitous sodium and potassium ions. A simple on-line sample preparation system comprising a microflow pumping system and 45 x 0.8-mm-i.d. microcolumns packed with weak or strong cation-exchange resins is described for the efficient removal of cations from nucleic acid samples. Samples were analyzed by flow injection analysis at a 3-5 microL/min flow of 10 mM triethylamine in 50% water-50% acetonitrile. After on-line desalting, mass spectra of oligonucleotides revealed no significant sodium adduct peaks. Moreover, signal-to-noise ratios were greatly enhanced compared to direct injection of the samples. Electrospray mass spectrometry with on-line sample preparation allowed accurate molecular mass determinations of picomole amounts of crude oligonucleotide preparations ranging in size from 8 to 80 nucleotides within a few minutes. The good linearity of the calibration plot (R2 = 0.9988) over at least 2 orders of magnitude and a relative standard deviation in peak areas of less than 9% permitted the sensitive quantitative measurement of oligonucleotides in a concentration range of 0.2-20 microM with selected-ion monitoring. Finally, the on-line sample preparation system was evaluated for the mass spectrometric analysis of complex oligonucleotide mixtures. PMID:9868919

  4. Esterification of oleic acid in a three-phase, fixed-bed reactor packed with a cation exchange resin catalyst.

    PubMed

    Son, Sung Mo; Kimura, Hiroko; Kusakabe, Katsuki

    2011-01-01

    Esterification of oleic acid was performed in a three-phase fixed-bed reactor with a cation exchange resin catalyst (Amberlyst-15) at high temperature, which was varied from 80 to 120 °C. The fatty acid methyl ester (FAME) yields in the fixed-bed reactor were increased with increases in the reaction temperature, methanol flow rate and bed height. Moreover, the FAME yields were higher than those obtained using a batch reactor due to an equilibrium shift toward the product that resulted from continuous evaporation of the produced water. In addition, there was no catalyst deactivation during the esterification of oleic acid. However, addition of sunflower oil to the oleic acid reduced the FAME yield obtained from simultaneous esterification and transesterification. The FAME yield was 97.5% at a reaction temperature of 100 °C in the fixed-bed with a height of 5 cm when the methanol and oleic acid feed rates were 8.6 and 9.0 mL/h, respectively.

  5. Comprehensive kinetic studies of acidic oil continuous esterification by cation-exchange resin in fixed bed reactors.

    PubMed

    Cheng, Yu; Feng, Yaohui; Ren, Yanbiao; Liu, Xuan; Gao, Aoran; He, Benqiao; Yan, Feng; Li, Jianxin

    2012-06-01

    Biodiesel produced by esterification from molar ratio of methanol to free fatty acid (FFA) as 25:1 in presence of triglyceride was carried out with cation-exchange resin as a heterogeneous catalyst in three different scales of fixed bed reactors from minireactor (6.8 mm × 110 mm) to pilot scale reactor (70 mm × 1260 mm) at 338 K. The kinetic study of esterification was undertaken in terms of pseudo-homogeneous mechanism and performed as a first order reaction with elimination of the solid-liquid internal and external mass transfer resistances. Moreover, a kinetic model of FFA esterification was developed to illustrate the relationship between the FFA conversion and the catalyst bed height of fixed bed reactor. The model was also suitable for various resins in fixed bed reactor. The theoretical predictions were in agreement with the experimental data with root mean square (RMS) errors <10.

  6. Gamma-aminobutyric acid production using immobilized glutamate decarboxylase followed by downstream processing with cation exchange chromatography.

    PubMed

    Lee, Seungwoon; Ahn, Jungoh; Kim, Yeon-Gu; Jung, Joon-Ki; Lee, Hongweon; Lee, Eun Gyo

    2013-01-15

    We have developed a gamma-aminobutyric acid (GABA) production technique using his-tag mediated immobilization of Escherichia coli-derived glutamate decarboxylase (GAD), an enzyme that catalyzes the conversion of glutamate to GABA. The GAD was obtained at 1.43 g/L from GAD-overexpressed E. coli fermentation and consisted of 59.7% monomer, 29.2% dimer and 2.3% tetramer with a 97.6% soluble form of the total GAD. The harvested GAD was immobilized to metal affinity gel with an immobilization yield of 92%. Based on an investigation of specific enzyme activity and reaction characteristics, glutamic acid (GA) was chosen over monosodium glutamate (MSG) as a substrate for immobilized GAD, resulting in conversion of 2.17 M GABA in a 1 L reactor within 100 min. The immobilized enzymes retained 58.1% of their initial activities after ten consecutive uses. By using cation exchange chromatography followed by enzymatic conversion, GABA was separated from the residual substrate and leached GAD. As a consequence, the glutamic acid was mostly removed with no detectable GAD, while 91.2% of GABA was yielded in the purification step.

  7. CATION EXCHANGE METHOD FOR THE RECOVERY OF PROTACTINIUM

    DOEpatents

    Studier, M.H.; Sullivan, J.C.

    1959-07-14

    A cation exchange prccess is described for separating protactinium values from thorium values whereby they are initially adsorbed together from an aqueous 0.1 to 2 N hydrochloric acid on a cation exchange resin in a column. Then selectively eluting the thorium by an ammonium sulfate solution and subsequently eluting the protactinium by an oxalate solution.

  8. Dynamics of the separation of amino acid and mineral salt in the stationary dialysis of solutions with an MK-40 profiled sulfo group cation exchange membrane

    NASA Astrophysics Data System (ADS)

    Vasil'eva, V. I.; Vorob'eva, E. A.

    2012-11-01

    The conjugated diffusion transport of amino acid and mineral salt through a profiled sulfo group cation exchange membrane that simulates the extraction of amino acid from wash waters of microbiological production containing mineral components not used in synthesis is studied. The competitive nature of the conjugation of flows resulting in a decrease in the rate of the mass transfer of components and their separation factor is established from a comparative analysis of experimental data on the diffusion transfer of phenylalanine and sodium chloride in the form of hydrogen from individual and mixed solutions through a profiled sulfo group cation exchange membrane. The range of concentrations and the ratio of components in solution corresponding to the effective separation of phenylalanine and sodium chloride are determined.

  9. Test procedure for cation exchange chromatography

    SciTech Connect

    Cooper, T.D.

    1994-08-24

    The purpose of this test plan is to demonstrate the synthesis of inorganic antimonate ion exchangers and compare their performance against the standard organic cation exchangers. Of particular interest is the degradation rate of both inorganic and organic cation exchangers. This degradation rate will be tracked by determining the ion exchange capacity and thermal stability as a function of time, radiation dose, and chemical reaction.

  10. Use of a polystyrene-divinylbenzene-based weakly acidic cation-exchange resin column and propionic acid as an eluent in ion-exclusion/adsorption chromatography of aliphatic carboxylic acids and ethanol in food samples.

    PubMed

    Mori, Masanobu; Hironaga, Takahiro; Kajiwara, Hiroe; Nakatani, Nobutake; Kozaki, Daisuke; Itabashi, Hideyuki; Tanaka, Kazuhiko

    2011-01-01

    We developed an ion-exclusion/adsorption chromatography (IEAC) method employing a polystyrene-divinylbenzene-based weakly acidic cation-exchange resin (PS-WCX) column with propionic acid as the eluent for the simultaneous determination of multivalent aliphatic carboxylic acids and ethanol in food samples. The PS-WCX column well resolved mono-, di-, and trivalent carboxylic acids in the acidic eluent. Propionic acid as the eluent gave a higher signal-to-noise ratio, and enabled sensitive conductimetric detection of analyte acids. We found the optimal separation condition to be the combination of a PS-WCX column and 20-mM propionic acid. Practical applicability of the developed method was confirmed by using a short precolumn with a strongly acidic cation-exchange resin in the H(+)-form connected before the separation column; this was to remove cations from food samples by converting them to hydrogen ions. Consequently, common carboxylic acids and ethanol in beer, wine, and soy sauce were successfully separated by the developed method.

  11. Ceramic Spheres From Cation Exchange Beads

    NASA Technical Reports Server (NTRS)

    Dynys, F. W.

    2003-01-01

    Porous ZrO2 and hollow TiO2 spheres were synthesized from a strong acid cation exchange resin. Spherical cation exchange beads, polystyrene based polymer, were used as a morphological-directing template. Aqueous ion exchange reaction was used to chemically bind (ZrO)(2+) ions to the polystyrene structure. The pyrolysis of the polystyrene at 600 C produces porous ZrO2 spheres with a surface area of 24 sq m/g with a mean sphere size of 42 microns. Hollow TiO2 spheres were synthesized by using the beads as a micro-reactor. A direct surface reaction - between titanium isopropoxide and the resin beads forms a hydrous TiO2 shell around the polystyrene core. The pyrolysis of the polystyrene core at 600 C produces hollow anatase spheres with a surface area of 42 sq m/g with a mean sphere size of 38 microns. The formation of ceramic spheres was studied by XRD, SEM and B.E.T. nitrogen adsorption measurements.

  12. Novel ultra stable silica-based stationary phases for reversed phase liquid chromatography--study of a hydrophobically assisted weak acid cation exchange phase.

    PubMed

    Zhang, Yu; Carr, Peter W

    2011-02-11

    A mixed-mode reversed-phase/weak cation exchange (RP/WCX) phase has been developed by introducing a small amount of carboxylate functionality into a hydrophobic hyper-crosslinked (HC) platform. This silica-based HC platform was designed to form an extensive polystyrene network completely confined to the particle's surface. The fully connected polymer network prevents the loss of bonded phase, which leads to superior hydrolytic stability of the new phase when compared to conventional silica-based phases. Compared to previously introduced HC phases the added carboxylic groups impart a new weak cation exchange selectivity to the base hydrophobic HC platform. The phase thus prepared shows a mixed-mode retention mechanism, allowing for both neutral organic compounds and bases of a wide polarity range to be simultaneously separated on the same phase under the same conditions. In addition, the new phase offers the flexibility that gradients in organic modifier, pH or ionic competitors can be used to affect the separation of a wide range of solutes. Moreover, the inherent weak acid cation exchange groups allow formic and acetic acid buffers to be used as eluents thereby avoiding the mass spectrometric ionization suppression problems concomitant to the use of non-volatile additives such as strong amine modifiers (e.g. triethylamine) or salts (e.g. NaCl) to elute basic solutes from the strong cation exchange phase which was previously developed in this lab. The use of the new phase for achieving strong retention of rather hydrophilic neurotransmitters and drugs of abuse without the need for ion pairing agents is demonstrated.

  13. Atmospheric deposition and canopy exchange of anions and cations in two plantation forests under acid rain influence

    NASA Astrophysics Data System (ADS)

    Shen, Weijun; Ren, Huili; Darrel Jenerette, G.; Hui, Dafeng; Ren, Hai

    2013-01-01

    Acid deposition as a widely concerned environmental problem in China has been less studied in plantation forests compared to urban and secondary forests, albeit they constitute 1/3 of the total forested areas of the country. We measured the rainwater amount and chemistry outside and beneath the canopies of two widely distributed plantations (Acacia mangium and Dimocarpus longan) in the severe acid rain influenced Pearl River Delta region of southeastern China for two years. Our results showed that the frequency of acid rain was 96% on the basis of pH value <5.6. The volume-weighted mean (vwm) pH was 4.62 and higher in the dry (Oct.-Mar.) than in the wet (Apr.-Sep.) seasons. The major acidic anion was sulfate with vwm concentration of 140 μeq l-1 and annual deposition flux of 110.3 kg ha-1 yr-1. The major neutralizing cations were calcium (94.8 μeq l-1 and 28 kg ha-1 yr-1) and ammonium (41.2 μeq l-1 and 11.7 kg ha-1 yr-1). Over 95% of these major acidic anions and neutralizing cations were derived from anthropogenic and terrestrial sources as a result of industrial, agricultural and forestry activities. Plantation canopy had marked impacts on rainwater chemistry, with the measured anion and cation concentrations being significantly enriched in throughfall (TF) and stemflow (SF) rainwater by 1.4 (for NO) to 20-fold (for K+) compared to those in bulk precipitation (BP). Dry deposition generally contributed about 13-22% of the total deposition while canopy leaching mainly occurred for K+ (>88%) and NH (10-38%). The two tree species showed distinct impacts on rainfall redistribution and rainwater chemistry due to their differences in canopy architecture and leaf/bark texture, suggesting that species-specific effects should not be overlooked while assessing the acid deposition in forested areas.

  14. Enrichment and low-level determination of glyphosate, aminomethylphosphonic acid and glufosinate in drinking water after cleanup by cation exchange resin.

    PubMed

    Küsters, Markus; Gerhartz, Michael

    2010-04-01

    For the determination of glyphosate, aminomethylphosphonic acid and glufosinate in drinking water, different procedures of enrichment and cleanup were examined using anion exchange or SPE. In many cases interactions of, e.g. alkaline earth metal ions especially calcium could be observed during enrichment and cleanup resulting in loss of analytes. For that reason, a novel cleanup and enrichment procedure for the determination of these phosphonic acid herbicides has been developed in drinking water using cation-exchange resin. In summary, the cleanup procedure with cation-exchange resin developed in this study avoids interactions as described above and is applicable to calcium-rich drinking water samples. After derivatization with 9-fluorenylmethylchloroformate followed by LC with fluorescence detection, LOD of 12, 14 and 12 ng/L and mean recoveries from real-world drinking water samples of 98+/-9, 100+/-16 and 101+/-11% were obtained for glyphosate, aminomethylphosphonic acid and glufosinate, respectively. The low LODs and the high precision permit the analysis of these phosphonic acid herbicides according to the guidelines of the European Commission.

  15. 2-Acrylamido-2-methyl-1-propanesulfonic Acid Grafted Poly(vinylidene fluoride-co-hexafluoropropylene)-Based Acid-/Oxidative-Resistant Cation Exchange for Membrane Electrolysis.

    PubMed

    Pandey, Ravi P; Das, Arindam K; Shahi, Vinod K

    2015-12-30

    For developing acid-/oxidative-resistant aliphatic-polymer-based cation-exchange membrane (CEM), macromolecular modification of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) was carried out by controlled chemical grafting of 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS). To introduce the unsaturation suitable for chemical grafting, dehydrofluorination of commercially available PVDF-co-HFP was achieved under alkaline medium. Sulfonated copolymer (SCP) was prepared by the free radical copolymerization of dehydofluorinated PVDF-co-HFP (DHPVDF-co-HFP) and AMPS in the presence of free radical initiator. Prepared SCP-based CEMs were analyzed for their morphological characteristics, ion-exchange capacity (IEC), water uptake, conductivity, and stabilities (mechanical, chemical, and thermal) in comparison with state-of-art Nafion117 membrane. High bound water content avoids the membrane dehydration, and most optimal (SCP-1.33) membrane exhibited about ∼2.5-fold high bound water content in comparison with that of Nafion117 membrane. Bunsen reaction of iodine-sulfur (I-S) was successfully performed by direct-contact-mode membrane electrolysis in a two-compartment electrolytic cell using different SCP membranes. High current efficiency (83-99%) confirmed absence of any side reaction and 328.05 kJ mol-H2(-1) energy was required for to produce 1 mol of H2 by electrolytic cell with SCP-1.33 membrane. In spite of low conductivity for reported SCP membrane in comparison with that of Nafion117 membrane, SCP-1.33 membrane was assessed as suitable candidate for electrolysis because of its low-cost nature and excellent stabilities in highly acidic environment may be due to partial fluorinated segments in the membrane structure.

  16. 2-Acrylamido-2-methyl-1-propanesulfonic Acid Grafted Poly(vinylidene fluoride-co-hexafluoropropylene)-Based Acid-/Oxidative-Resistant Cation Exchange for Membrane Electrolysis.

    PubMed

    Pandey, Ravi P; Das, Arindam K; Shahi, Vinod K

    2015-12-30

    For developing acid-/oxidative-resistant aliphatic-polymer-based cation-exchange membrane (CEM), macromolecular modification of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) was carried out by controlled chemical grafting of 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS). To introduce the unsaturation suitable for chemical grafting, dehydrofluorination of commercially available PVDF-co-HFP was achieved under alkaline medium. Sulfonated copolymer (SCP) was prepared by the free radical copolymerization of dehydofluorinated PVDF-co-HFP (DHPVDF-co-HFP) and AMPS in the presence of free radical initiator. Prepared SCP-based CEMs were analyzed for their morphological characteristics, ion-exchange capacity (IEC), water uptake, conductivity, and stabilities (mechanical, chemical, and thermal) in comparison with state-of-art Nafion117 membrane. High bound water content avoids the membrane dehydration, and most optimal (SCP-1.33) membrane exhibited about ∼2.5-fold high bound water content in comparison with that of Nafion117 membrane. Bunsen reaction of iodine-sulfur (I-S) was successfully performed by direct-contact-mode membrane electrolysis in a two-compartment electrolytic cell using different SCP membranes. High current efficiency (83-99%) confirmed absence of any side reaction and 328.05 kJ mol-H2(-1) energy was required for to produce 1 mol of H2 by electrolytic cell with SCP-1.33 membrane. In spite of low conductivity for reported SCP membrane in comparison with that of Nafion117 membrane, SCP-1.33 membrane was assessed as suitable candidate for electrolysis because of its low-cost nature and excellent stabilities in highly acidic environment may be due to partial fluorinated segments in the membrane structure. PMID:26642107

  17. Cation exchange capacity of pine bark substrates

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cation exchange capacity (CEC) is an important soil and substrate chemical property. It describes a substrate's ability to retain cation nutrients. Higher CEC values for a substrate generally result in greater amounts of nutrients retained in the substrate and available for plant uptake, and great...

  18. Advancements in Anion Exchange Membrane Cations

    SciTech Connect

    Sturgeon, Matthew R.; Long, Hai; Park, Andrew M.; Pivovar, Bryan S.

    2015-10-15

    Anion-exchange membrane fuel cells (AME-FCs) are of increasingly popular interest as they enable the use of non-Pt fuel cell catalysts, the primary cost limitation of proton exchange membrane fuel cells. Benzyltrimethyl ammonium (BTMA) is the standard cation that has historically been utilized as the hydroxide conductor in AEMs. Herein we approach AEMs from two directions. First and foremost we study the stability of several different cations in a hydroxide solution at elevated temperatures. We specifically targeted BTMA and methoxy and nitro substituted BTMA. We've also studied the effects of adding an akyl spacer units between the ammonium cation and the phenyl group. In the second approach we use computational studies to predict stable ammonium cations, which are then synthesized and tested for stability. Our unique method to study cation stability in caustic conditions at elevated temperatures utilizes Teflon Parr reactors suitable for use under various temperatures and cation concentrations. NMR analysis was used to determine remaining cation concentrations at specific time points with GCMS analysis verifying product distribution. We then compare the experimental results with calculated modeling stabilities. Our studies show that the electron donating methoxy groups slightly increase stability (compared to that of BTMA), while the electron withdrawing nitro groups greatly decrease stability in base. These results give insight into possible linking strategies to be employed when tethering a BTMA like ammonium cation to a polymeric backbone; thus synthesizing an anion exchange membrane.

  19. Forging Colloidal Nanostructures via Cation Exchange Reactions

    PubMed Central

    2016-01-01

    Among the various postsynthesis treatments of colloidal nanocrystals that have been developed to date, transformations by cation exchange have recently emerged as an extremely versatile tool that has given access to a wide variety of materials and nanostructures. One notable example in this direction is represented by partial cation exchange, by which preformed nanocrystals can be either transformed to alloy nanocrystals or to various types of nanoheterostructures possessing core/shell, segmented, or striped architectures. In this review, we provide an up to date overview of the complex colloidal nanostructures that could be prepared so far by cation exchange. At the same time, the review gives an account of the fundamental thermodynamic and kinetic parameters governing these types of reactions, as they are currently understood, and outlines the main open issues and possible future developments in the field. PMID:26891471

  20. Magnetic graphene - polystyrene sulfonic acid nano composite: A dispersive cation exchange sorbent for the enrichment of aminoalcohols and ethanolamines from environmental aqueous samples.

    PubMed

    Chinthakindi, Sridhar; Purohit, Ajay; Singh, Varoon; Tak, Vijay; Dubey, D K; Pardasani, Deepak

    2015-12-01

    Present study aimed at graphene surface modification to achieve selective analyte binding in dispersive solid phase extraction. Magnetic graphene - polystyrene sulfonic acid (MG-PSS) cation exchange nano-composite was prepared by non-covalent wrapping method. Composite was characterized by FT-IR and zeta potential. Material exhibited good dispersion in water and high exchange capacity of 1.97±0.16mMg(-1). Prepared nano-sorbent was then exploited for the cation exchange extraction and gas chromatography mass spectrometric analysis of Chemical Weapons Convention relevant aminoalcohols and ethanolamines from aqueous samples. Extraction parameters such as sorbent amount, extraction time, desorption conditions and sample pH were optimized and effect of common matrix interferences such as polyethylene glycol and metal salts was also studied. Three milligram of sorbent per mL of sample with 20min of extraction time at room temperature afforded 70-81% recoveries of the selected analytes spiked at concentration level of 1μgmL(-1). Method showed good linearity in the studied range with r(2)≥0.993. The limits of detection and limits of quantification ranged from 23 to 54ngmL(-1) and 72 to 147ngmL(-1), respectively. The relative standard deviation for intra- and inter-day precision ranged from 4.6 to 10.2% and 7.4 to 14.8% respectively. Applicability of the method to different environmental samples as well as the proficiency tests conducted by the Organization for the Prohibition of Chemical Weapons (OPCW) was also ascertained.

  1. Rapid method of separating Am(VI) from transplutonium and rare-earth elements on a cation exchanger in phosphoric acid

    SciTech Connect

    Tikhomirova, G.S.; Guseva, L.I.

    1988-07-01

    Measurements have been made on cation-exchanger sorption of americium, other actinoids, and certain rare-earth elements from 0.1-2.0 M H/sub 3/PO/sub 4/ when the elements have been oxidized with ammonium persulfate alone or mixed with silver phosphate. There are considerable differences in behavior between the americium and the other elements on account of its being oxidized to a higher valency state. Measurements have been made on the effects of acid and oxidant concentrations and of the oxidation and elution conditions on the americium yield when the exchanger is treated with H/sub 3/PO/sub 4/. Optimum oxidation conditions have been chosen, and a rapid method has been devised for separating americium(VI) from other transplutonium elements and REE on Dowex 50 /times/ 8, where the eluent is 0.1-1.0 M H/sub 3/PO/sub 4/ plus 0.05 M (NH/sub 4/)/sub 2/S/sub 2/O/sub 8/.

  2. Cation exchange interaction between antibiotic ciprofloxacin and montmorillonite.

    PubMed

    Wang, Chih-Jen; Li, Zhaohui; Jiang, Wei-Teh; Jean, Jiin-Shuh; Liu, Chia-Chuan

    2010-11-15

    Exploring the interactions between antibiotics and soils/minerals is of great importance in resolving their fate, transport, and elimination in the environment due to their frequent detection in wastewater, river water, sewage sludge and soils. This study focused on determining the adsorption properties and mechanisms of interaction between antibiotic ciprofloxacin and montmorillonite (SAz-1), a swelling dioctahedral mineral with Ca(2+) as the main interlayer cation. In acidic and neutral aqueous solutions, a stoichiometric exchange between ciprofloxacin and interlayer cations yielded an adsorption capacity as high as 330 mg/g, corresponding to 1.0 mmol/g. When solution pH was above its pK(a2) (8.7), adsorption of ciprofloxacin was greatly reduced due to the net repulsion between the negatively charged clay surfaces and the ciprofloxacin anion. The uptake of ciprofloxacin expanded the basal spacing (d(001)) of montmorillonite from 15.04 to 17.23 A near its adsorption capacity, confirming cation exchange within the interlayers in addition to surface adsorption. Fourier transform infrared results further suggested that the protonated amine group of ciprofloxacin in its cationic form was electrostatically attracted to negatively charged sites of clay surfaces, and that the carboxylic acid group was hydrogen bonded to the basal oxygen atoms of the silicate layers. The results indicate that montmorillonite is an effective sorbent to remove ciprofloxacin from water. PMID:20675045

  3. Determination of hydrogen ion by ion chromatography (IC) with sulfonated cation-exchange resin as the stationary phase and aqueous EDTA (ethylenediamine-N,N,N',N'-tetraacetic acid) solution as the mobile phase.

    PubMed

    Hu, W; Iles, A; Hasebe, K; Matsukami, H; Cao, S; Tanaka, K

    2001-05-01

    An ion chromatographic (IC) method has been developed for determination of hydrogen ion (H+). It is based on the use of sulfonated cation-exchange resin as stationary phase, aqueous ethylenediamine-N,N,N',N'-tetraacetic acid (dipotassium salt, EDTA-2K, written as K2H2Y) solution as mobile phase, and conductivity for detection. H+ was separated mainly by cation-exchange, but its elution was accelerated by the presence of EDTA. The order of elution for the model cations was H+ > Li+ > Na+ > NH4+ > Ca2+ > > Mg2+. A sharp and highly symmetrical peak was obtained for H+ and this was attributed to the capacity of H2Y2(2-) to receive and bind H+. H+ was detected conductiometrically and detector response (reduction in conductivity as a result of H+ +H2Y2- --> H3Y-) was linearly proportional to the concentration of H+ in the sample. The detection limit for H+ with this IC system was better than 4.7 micromol L(-1). A significant advantage of this method was the ability to separate and determine, in one step, H+ and other cations. The successful determination of H+ and other cation species in real acid-rain samples demonstrated the usefulness of this method.

  4. Sorption mechanism and predictive models for removal of cationic organic contaminants by cation exchange resins.

    PubMed

    Jadbabaei, Nastaran; Zhang, Huichun

    2014-12-16

    Understanding the sorption mechanism of organic contaminants on cation exchange resins (CXRs) will enable application of these resins for the removal of cationic organic compounds from contaminated water. In this study, sorption of a diverse set of 12 organic cations and 8 neutral aromatic solutes on two polystyrene CXRs, MN500 and Amberlite 200, was examined. MN500 showed higher sorbed concentrations due to its microporous structure. The sorbed concentrations followed the same trend of aromatic cations > aliphatic cations > neutral solutes for both resins. Generally, solute-solvent interactions, nonpolar moiety of the solutes, and resin matrix can affect selectivity of the cations. Sorbed concentrations of the neutral compounds were significantly less than those of the cations, indicating a combined effect of electrostatic and nonelectrostatic interactions. By conducting multiple linear regression between Gibbs free energy of sorption and Abraham descriptors for all 20 compounds, polarity/polarizability (S), H-bond acidity (A), induced dipole (E), and electrostatic (J(+)) interactions were found to be involved in the sorption of the cations by the resins. After converting the aqueous sorption isotherms to sorption from the ideal gas-phase by water-wet resins, a more significant effect of J(+) was observed. Predictive models were then developed based on the linear regressions and validated by accurately estimating the sorption of different test set compounds with a root-mean-square error range of 0.91-1.1 and 0.76-0.85 for MN500 and Amberlite 200, respectively. The models also accurately predicted sorption behavior of aniline and imidazole between pH 3 and 10. PMID:25409479

  5. Solvent-dependent cation exchange in metal-organic frameworks.

    PubMed

    Brozek, Carl K; Bellarosa, Luca; Soejima, Tomohiro; Clark, Talia V; López, Núria; Dincă, Mircea

    2014-06-01

    We investigated which factors govern the critical steps of cation exchange in metal-organic frameworks by studying the effect of various solvents on the insertion of Ni(2+) into MOF-5 and Co(2+) into MFU-4l. After plotting the extent of cation insertion versus different solvent parameters, trends emerge that offer insight into the exchange processes for both systems. This approach establishes a method for understanding critical aspects of cation exchange in different MOFs and other materials.

  6. CATIONIC EXCHANGE PROCESS FOR THE SEPARATION OF RARE EARTHS

    DOEpatents

    Choppin, G.R.; Thompson, S.G.; Harvey, B.G.

    1960-02-16

    A process for separating mixtures of elements in the lanthanum and actinium series of the periodic table is described. The mixture of elements is dissolved in 0.05 M HCI, wherein the elements exist as tripositive ions. The resulting solution is then transferred to a column of cationic exchange resin and the column eluted with 0.1 to 0.6 M aqueous ammonium alpha hydroxy isobutyrate solution of pH 3.8 to 5.0. The use of ammonium alpha hydroxy isobutyrate as an eluting agent results in sharper and more rapid separations than previously obtainable with eluants such as citric, tartaric, glycolic, and lactic acids.

  7. Selective separation of sodium ions from a mixture with phenylalanine by Donnan dialysis with a profiled sulfogroup cation exchange membrane

    NASA Astrophysics Data System (ADS)

    Vasil'eva, V. I.; Goleva, E. A.

    2013-11-01

    The possibility of separating ions of metal from a mixture with ampholyte (an amino acid) by Donnan dialysis with an MK-40 sulfogroup cation exchange membrane is demonstrated. Conditions ensuring the selectivity and intensity of the mass transfer of sodium ions from a mixture with bipolar phenylalanine ions into a diffusate containing hydrochloric acid through a cation exchange membrane are found.

  8. Cation exchange properties of zeolites in hyper alkaline aqueous media.

    PubMed

    Van Tendeloo, Leen; de Blochouse, Benny; Dom, Dirk; Vancluysen, Jacqueline; Snellings, Ruben; Martens, Johan A; Kirschhock, Christine E A; Maes, André; Breynaert, Eric

    2015-02-01

    Construction of multibarrier concrete based waste disposal sites and management of alkaline mine drainage water requires cation exchangers combining excellent sorption properties with a high stability and predictable performance in hyper alkaline media. Though highly selective organic cation exchange resins have been developed for most pollutants, they can serve as a growth medium for bacterial proliferation, impairing their long-term stability and introducing unpredictable parameters into the evolution of the system. Zeolites represent a family of inorganic cation exchangers, which naturally occur in hyper alkaline conditions and cannot serve as an electron donor or carbon source for microbial proliferation. Despite their successful application as industrial cation exchangers under near neutral conditions, their performance in hyper alkaline, saline water remains highly undocumented. Using Cs(+) as a benchmark element, this study aims to assess the long-term cation exchange performance of zeolites in concrete derived aqueous solutions. Comparison of their exchange properties in alkaline media with data obtained in near neutral solutions demonstrated that the cation exchange selectivity remains unaffected by the increased hydroxyl concentration; the cation exchange capacity did however show an unexpected increase in hyper alkaline media.

  9. Determination of the Cation-Exchange Capacity of Muscovite Mica.

    PubMed

    Osman; Suter

    2000-04-01

    High cation-exchange capacity (CEC) muscovite mica with a homoionic surface was prepared by replacing the Li(+) surface ions of partially delaminated Li-mica with K(+). The CEC of this K-mica was determined by exchanging its surface cations with Cs(+), NH(+)(4), methylene blue (MB(+)), and copper triethylenetetramine [Cu(trien)(2+)]. The kinetics of these exchange reactions were studied and showed large differences depending on their relative affinities to mica. The NH(4)(+)/K(+) exchange was slow, while the Cs(+) and Cu(trien)(2+)/K(+) exchange was fast. The MB(+)/K(+) exchange was quite slow and was not completed even after 99 h. Insufficient reaction time is one of the main reasons for the contradictory results reported in the literature for the CEC of aluminosilicates obtained by different methods. The CEC of mica can be photometrically measured by exchanging its surface cations with Cu(trien)(2+). Copyright 2000 Academic Press.

  10. Cation-exchange chromatography of monoclonal antibodies

    PubMed Central

    Urmann, Marina; Graalfs, Heiner; Joehnck, Matthias; Jacob, Lothar R

    2010-01-01

    A novel cation-exchange resin, Eshmuno™ S, was compared to Fractogel® SO3− (M) and Toyopearl GigaCap S-650M. The stationary phases have different base matrices and carry specific types of polymeric surface modifications. Three monoclonal antibodies (mAbs) were used as model proteins to characterize these chromatographic resins. Results from gradient elutions, stirred batch adsorptions and confocal laser scanning microscopic investigations were used to elucidate binding behavior of mAbs onto Eshmuno™ S and Fractogel® SO3− and the corresponding transport mechanisms on these two resins. The number of charges involved in mAb binding for Eshmuno™ S is lower than for Fractogel® SO3−, indicating a slightly weaker electrostatic interaction. Kinetics from batch uptake experiments are compared to kinetic data obtained from confocal laser scanning microscopy images. Both experimental approaches show an accelerated protein adsorption for the novel stationary phase. The influence of pH, salt concentrations and residence times on dynamic binding capacities was determined. A higher dynamic binding capacity for Eshmuno™ S over a wider range of pH values and residence times was found compared to Fractogel® SO3− and Toyopearl GigaCap S-650M. The capture of antibodies from cell culture supernatant, as well as post-protein A eluates, were analyzed with respect to their host cell protein (hcp) removal capabilities. Comparable or even better hcp clearance was observed at much higher protein loading for Eshmuno™ S than Fractogel® SO3− or Toyopearl GigaCap S-650M. PMID:20559022

  11. Nutrient leaching from conifer needles in relation to foliar apoplast cation-exchange capacity

    SciTech Connect

    Turner, D.P.; van Broekhuizen, H.J.

    1992-01-01

    Limited evidence to date suggests that acidic precipitation promotes leaching of nutrient cations from conifer foliage. In order to evaluate the relative contribution of the apoplast cation exchange complex and symplast nutrient pools to the leached ions, the magnitude of potential foliar leaching in response to acidic precipitation was compared to foliar apoplast cation exchange capacity (CEC) for two conifer tree species (Pseudotsuga menziesii and Picea engelmanii). Leaching increased with decreasing pH and increasing time of immersion. At pH 2.1 and 3.1, equivalents of H+ depleted from the acidic solutions approximated equivalent of cations gained by the solutions. Maximum amounts leached were less than 40 micro equiv/g dry weight of needles for all ions combined. Measured foliar apoplast CEC for these species was approximately 120 micro equiv/g dry weight of needles. These relative magnitudes indicated that the apoplast provided the leached ions.

  12. A Scale Model of Cation Exchange for Classroom Demonstration.

    ERIC Educational Resources Information Center

    Guertal, E. A.; Hattey, J. A.

    1996-01-01

    Describes a project that developed a scale model of cation exchange that can be used for a classroom demonstration. The model uses kaolinite clay, nails, plywood, and foam balls to enable students to gain a better understanding of the exchange complex of soil clays. (DDR)

  13. All-Inorganic Germanium Nanocrystal Films by Cationic Ligand Exchange.

    PubMed

    Wheeler, Lance M; Nichols, Asa W; Chernomordik, Boris D; Anderson, Nicholas C; Beard, Matthew C; Neale, Nathan R

    2016-03-01

    We introduce a new paradigm for group IV nanocrystal surface chemistry based on room temperature surface activation that enables ionic ligand exchange. Germanium nanocrystals synthesized in a gas-phase plasma reactor are functionalized with labile, cationic alkylammonium ligands rather than with traditional covalently bound groups. We employ Fourier transform infrared and (1)H nuclear magnetic resonance spectroscopies to demonstrate the alkylammonium ligands are freely exchanged on the germanium nanocrystal surface with a variety of cationic ligands, including short inorganic ligands such as ammonium and alkali metal cations. This ionic ligand exchange chemistry is used to demonstrate enhanced transport in germanium nanocrystal films following ligand exchange as well as the first photovoltaic device based on an all-inorganic germanium nanocrystal absorber layer cast from solution. This new ligand chemistry should accelerate progress in utilizing germanium and other group IV nanocrystals for optoelectronic applications.

  14. All-inorganic Germanium nanocrystal films by cationic ligand exchange

    DOE PAGES

    Wheeler, Lance M.; Nichols, Asa W.; Chernomordik, Boris D.; Anderson, Nicholas C.; Beard, Matthew C.; Neale, Nathan R.

    2016-01-21

    In this study, we introduce a new paradigm for group IV nanocrystal surface chemistry based on room temperature surface activation that enables ionic ligand exchange. Germanium nanocrystals synthesized in a gas-phase plasma reactor are functionalized with labile, cationic alkylammonium ligands rather than with traditional covalently bound groups. We employ Fourier transform infrared and 1H nuclear magnetic resonance spectroscopies to demonstrate the alkylammonium ligands are freely exchanged on the germanium nanocrystal surface with a variety of cationic ligands, including short inorganic ligands such as ammonium and alkali metal cations. This ionic ligand exchange chemistry is used to demonstrate enhanced transport inmore » germanium nanocrystal films following ligand exchange as well as the first photovoltaic device based on an all-inorganic germanium nanocrystal absorber layer cast from solution. This new ligand chemistry should accelerate progress in utilizing germanium and other group IV nanocrystals for optoelectronic applications.« less

  15. Cu Vacancies Boost Cation Exchange Reactions in Copper Selenide Nanocrystals

    PubMed Central

    2015-01-01

    We have investigated cation exchange reactions in copper selenide nanocrystals using two different divalent ions as guest cations (Zn2+ and Cd2+) and comparing the reactivity of close to stoichiometric (that is, Cu2Se) nanocrystals with that of nonstoichiometric (Cu2–xSe) nanocrystals, to gain insights into the mechanism of cation exchange at the nanoscale. We have found that the presence of a large density of copper vacancies significantly accelerated the exchange process at room temperature and corroborated vacancy diffusion as one of the main drivers in these reactions. Partially exchanged samples exhibited Janus-like heterostructures made of immiscible domains sharing epitaxial interfaces. No alloy or core–shell structures were observed. The role of phosphines, like tri-n-octylphosphine, in these reactions, is multifaceted: besides acting as selective solvating ligands for Cu+ ions exiting the nanoparticles during exchange, they also enable anion diffusion, by extracting an appreciable amount of selenium to the solution phase, which may further promote the exchange process. In reactions run at a higher temperature (150 °C), copper vacancies were quickly eliminated from the nanocrystals and major differences in Cu stoichiometries, as well as in reactivities, between the initial Cu2Se and Cu2–xSe samples were rapidly smoothed out. These experiments indicate that cation exchange, under the specific conditions of this work, is more efficient at room temperature than at higher temperature. PMID:26140622

  16. Simultaneous determination of urinary creatinine and UV-absorbing amino acids using a novel low-capacity cation-exchange chromatography for the screening of inborn errors of metabolism.

    PubMed

    Yokoyama, Yukio; Yamasaki, Keiko; Sato, Hisakuni

    2005-02-25

    A simple and versatile low-capacity cation-exchange chromatography system for the simultaneous determination of creatinine and UV-absorbing amino acids was developed. The separation column was packed with a newly developed low-capacity sulfoacylated macro-porous polystyrene-divinylbenzene resin selective for amino-acid cations. Urinary creatinine, creatine, tyrosine, histidine, phenylalanine, and tryptophan were simultaneously separated and determined by an isocratic elution with phosphate/acetonitrile eluent in 25 min. Relative standard deviations (R.S.D.) of the retention times for the analytes were between 0.28 and 1.06%. R.S.D. of peak area responses for the analytes were between 0.75 and 3.51%. The r(2) values for the calibration lines were between 0.9994 and 0.9999. The method could provide the creatinine ratios for the analytes, and was applicable to the screening and/or chemical diagnosis of several inherited disorders of amino-acid metabolism such as phenylketonuria (PKU). PMID:15664367

  17. Porous Ceramic Spheres From Cation Exchange Beads

    NASA Technical Reports Server (NTRS)

    Dynys, Fred

    2005-01-01

    This document is a slide presentation that examines the use of a simple templating process to produce hollow ceramic spheres with a pore size of 1 to 10 microns. Using ion exchange process it was determined that the method produces porous ceramic spheres with a unique structure: (i.e., inner sphere surrounded by an outer sphere.)

  18. Determination of the cation-exchange capacity of muscovite mica

    SciTech Connect

    Osman, M.A.; Suter, U.W.

    2000-04-01

    High cation-exchange capacity (CEC) muscovite mica with a homoionic surface was prepared by replacing the Li{sup +} surface ions of partially delaminated Li-mica with K{sup +}. The CEC of this K-mica was determined by exchanging its surface cations with Cs{sup +}, NH{sub 4}{sup +}, methylene blue (MB{sup +}), and copper triethylenetetramine [Cu(trien){sup 2+}]. The kinetics of these exchange reactions were studied and showed large differences depending on their relative affinities to mica. The NH{sub 4}{sup +}/K{sup +} exchange was slow, while the Cs{sup +} and Cu(trien){sup 2+}/K{sup +} exchange was fast. The MB{sup +}/K{sup +} exchange was quite slow and was not completed even after 99 h. Insufficient reaction time is one of the main reasons for the contradictory results reported in the literature for the CEC of aluminosilicates obtained by different methods. The CEC of mica can be photometrically measured by exchanging its surface cations with Cu(trien){sup 2+}.

  19. Sn Cation Valency Dependence in Cation Exchange Reactions Involving Cu2-xSe Nanocrystals

    PubMed Central

    2014-01-01

    We studied cation exchange reactions in colloidal Cu2-xSe nanocrystals (NCs) involving the replacement of Cu+ cations with either Sn2+ or Sn4+ cations. This is a model system in several aspects: first, the +2 and +4 oxidation states for tin are relatively stable; in addition, the phase of the Cu2-xSe NCs remains cubic regardless of the degree of copper deficiency (that is, “x”) in the NC lattice. Also, Sn4+ ions are comparable in size to the Cu+ ions, while Sn2+ ones are much larger. We show here that the valency of the entering Sn ions dictates the structure and composition not only of the final products but also of the intermediate steps of the exchange. When Sn4+ cations are used, alloyed Cu2–4ySnySe NCs (with y ≤ 0.33) are formed as intermediates, with almost no distortion of the anion framework, apart from a small contraction. In this exchange reaction the final stoichiometry of the NCs cannot go beyond Cu0.66Sn0.33Se (that is Cu2SnSe3), as any further replacement of Cu+ cations with Sn4+ cations would require a drastic reorganization of the anion framework, which is not possible at the reaction conditions of the experiments. When instead Sn2+ cations are employed, SnSe NCs are formed, mostly in the orthorhombic phase, with significant, albeit not drastic, distortion of the anion framework. Intermediate steps in this exchange reaction are represented by Janus-type Cu2-xSe/SnSe heterostructures, with no Cu–Sn–Se alloys. PMID:25340627

  20. Cationic Lipid-Based Nucleic Acid Vectors.

    PubMed

    Jubeli, Emile; Goldring, William P D; Pungente, Michael D

    2016-01-01

    The delivery of nucleic acids into cells remains an important laboratory cell culture technique and potential clinical therapy, based upon the initial cellular uptake, then translation into protein (in the case of DNA), or gene deletion by RNA interference (RNAi). Although viral delivery vectors are more efficient, the high production costs, limited cargo capacity, and the potential for clinical adverse events make nonviral strategies attractive. Cationic lipids are the most widely applied and studied nonviral vectors; however, much remains to be solved to overcome limitations of these systems. Advances in the field of cationic lipid-based nucleic acid (lipoplex) delivery rely upon the development of robust and reproducible lipoplex formulations, together with the use of cell culture assays. This chapter provides detailed protocols towards the formulation, delivery, and assessment of in vitro cationic lipid-based delivery of DNA. PMID:27436310

  1. Selective Facet Reactivity During Cation Exchange in Cadmium Sulfide Nanorods

    SciTech Connect

    Sadtler, Bryce; Demchenko, Denis; Zheng, Haimei; Hughes, Steven; Merkle, Maxwell; Dahmen, Ulrich; Wang, Lin-Wang; Alivisatos, A. Paul

    2008-12-18

    The partial transformation of ionic nanocrystals through cation exchange has been used to synthesize nanocrystal heterostructures. We demonstrate that the selectivity for cation exchange to take place at different facets of the nanocrystal plays an important role in determining the resulting morphology of the binary heterostructure. In the case of copper I (Cu+) cation exchange in cadmium sulfide (CdS) nanorods, the reaction starts preferentially at the ends of the nanorods such that copper sulfide (Cu2S) grows inwards from either end. The resulting morphology is very different from the striped pattern obtained in our previous studies of silver I (Ag+) exchange in CdS nanorods where non-selective nucleation of silver sulfide (Ag2S) occurs. From interface formation energies calculated for several models of epitaxialconnections between CdS and Cu2S or Ag2S, we infer the relative stability of each interface during the nucleation and growth of Cu2S or Ag2S within the CdS nanorods. The epitaxial connections of Cu2S to the end facets of CdS nanorods minimize the formation energy, making these interfaces stable throughout the exchange reaction. However, as the two end facets of wurtzite CdS nanorods are crystallographically nonequivalent, asymmetric heterostructures can be produced.

  2. Effect of cation contamination and hydrated pressure loading on the mechanical properties of proton exchange membranes

    NASA Astrophysics Data System (ADS)

    Jia, Ruiliang; Han, Binghong; Levi, Kemal; Hasegawa, Takuya; Ye, Jiping; Dauskardt, Reinhold H.

    Perfluorosulfonic acid (PFSA) polymer membranes are widely used as electrolyte thin films to transport protons in proton exchange membrane (PEM) fuel cells. The mechanical degradation of the membrane represents a common failure mode that limits the operational life of the fuel cells. In the present work, effect of contamination related to cation exchange on the mechanical reliability of PEMs was investigated. We applied the bulge test technique to assess the mechanical properties of Nafion ® PFSA membranes simulating pressure loading on hydrated PEMs in fuel cells. The corresponding elastic moduli of Nafion ® before and after cation exchange were analyzed and compared with the results measured by uniaxial tension experiments at selected humidity conditions, showing increasing stiffness with the increase of cation radius. We also used the out-of-plane tearing test method to characterize the fracture behaviors of PEMs. The effects of cation exchange and water absorption on mechanical and fracture properties of PEMs at different temperatures are discussed in terms of cation and water interactions with the molecular structure of PFSA polymers.

  3. Simulated Transport of Three Cations Through Porous Media: Effect of Different Approaches to Modeling Cation Exchange Reactions

    NASA Astrophysics Data System (ADS)

    Grant, S. A.; Mansell, R. S.; Bloom, S. A.; Rhue, R. D.

    1995-01-01

    Batch cation exchange and column experiments were conducted to evaluate selectivity coefficients which have been suggested for describing cation exchange reactions in solute transport models. Vanselow selectivity coefficients were calculated for cation exchange equilibria with a cation resin and for equilibria reported in the literature with a Yolo loam soil. Experimental column data were compared with data from simulations generated by a numerical solute transport model to evaluate Vanselow, Gaines-Thomas, and statistical thermodynamic selectivity coefficients. With the cation resin, the statistical thermodynamic selectivity coefficient gave the most reliable estimate of column effluent cation concentrations. In a column packed with the Yolo loam soil, the Vanselow selectivity coefficient gave the most accurate prediction of column response. Use of variable (as opposed to fixed) Vanselow selectivity coefficients gave more accurate predictions of column experiments. The use of ternary cation exchange data did not improve predictions of column response.

  4. Effects of exchanged cation on the microporosity of montmorillonite

    USGS Publications Warehouse

    Rutherford, D.W.; Chiou, C.T.; Eberl, D.D.

    1997-01-01

    The micropore volumes of 2 montmorillonites (SAz- 1 and SWy-1), each exchanged with Ca, Na, K, Cs and tetramethylammonium (TMA) ions, were calculated from the measured vapor adsorption data of N2 and neo-hexane by use of t- and ??s-plots. The corresponding surface areas of the exchanged clays were determined from Brunauer-Emmett-Teller (BET) plots of N2 adsorption data. Micropore volumes and surface areas of the samples increased with the size of exchanged cation: TMA > Cs > K> Ca > Na. The SAz-1 exchanged clays showed generally greater micropore volumes and surface areas than the corresponding SWy-1 clays. The vapor adsorption data and d(001) measurements for dry clay samples were used together to evaluate the likely locations and accessibility of clay micropores, especially the relative accessibility of their interlayer spacing. For both source clays exchanged with Na, Ca and K ions, the interlayer spacing appeared to be too small to admit nonpolar gases and the accessible micropores appeared to have dimensions greater than 5.0 A??, the limiting molecular dimension of neo -hexane. In these systems, there was a good consistency of micropore volumes detected by N2 and neo-hexane. When the clays were intercalated with relatively large cations (TMA and possibly Cs), the large layer expansion created additional microporosity, which was more readily accessible to small N2 than to relatively large neo-hexane. Hence, the micropore volume as detected by N2 was greater than that detected by neo-hexane. The micropore volumes with pore dimensions greater than 5 A?? determined for clays exchanged with Na, Ca and K likely resulted from the pores on particle edges and void created by overlap regions of layers. The increase in micropore volumes with pore dimensions less than 5 A?? determined for clays exchanged with TMA and possibly Cs could be caused by opening of the interlayer region by the intercalation of these large cations.

  5. Glutathione-based zwitterionic stationary phase for hydrophilic interaction/cation-exchange mixed-mode chromatography.

    PubMed

    Shen, Aijin; Li, Xiuling; Dong, Xuefang; Wei, Jie; Guo, Zhimou; Liang, Xinmiao

    2013-11-01

    As a naturally hydrophilic peptide, glutathione was facilely immobilized onto silica surface to obtain a novel hydrophilic interaction/cation-exchange mixed-mode chromatographic stationary phase (Click TE-GSH) via copper-free "thiol-ene" click chemistry. The resulting material was characterized by solid state (13)C/CP MAS NMR and elemental analysis. The measurement of ζ-potential indicated the cation-exchange characteristics and adjustable surface charge density of Click TE-GSH material. The influence of acetonitrile content and pH value on the retention of ionic compounds was investigated for understanding the chromatographic behaviors. The results demonstrated that Click TE-GSH column could provide both hydrophilic and cation-exchange interaction. Taking advantage of the good hydrophilicity and inherent cation-exchange characteristics of Click TE-GSH material, the resolution of neutral fructosan with high degree of polymerization (DP), basic chitooligosaccharides and strongly acidic carrageenan oligosaccharides was successfully realized in hydrophilic interaction chromatography (HILIC), hydrophilic interaction/cation-exchange mixed-mode chromatography (HILIC/CEX), cation-exchange chromatography (CEX) and electrostatic repulsion/hydrophilic interaction chromatography (ERLIC). On the other hand, the separation of standard peptides varying in hydrophobicity/hydrophilicity and charge was achieved in both CEX and HILIC/CEX mode with high efficiency and distinct selectivity. To further demonstrate the versatility and applicability of Click TE-GSH stationary phase, the separation of a human serum albumin (HSA) tryptic digest was performed in HILIC/CEX mode. Peptides were adequately resolved and up to 86 HSA peptides were identified with sequence coverage of 85%. The results indicated the good potential of Click TE-GSH material in glycomics and proteomics. PMID:24075460

  6. Analysis of neuropeptide Y and its metabolites by high-performance liquid chromatography-electrospray ionization mass spectrometry and integrated sample clean-up with a novel restricted-access sulphonic acid cation exchanger.

    PubMed

    Racaityte, K; Lutz ESM; Unger, K K; Lubda, D; Boos, K S

    2000-08-18

    A novel restricted access cation exchanger with sulphonic acid groups at the internal surface was proven to be highly suitable in the sample clean up of peptides on-line coupled to HPLC-electrospray ionization (ESI)-MS. Neuropeptide Y (NPY) and several of its fragments in plasma were subjected to the sample clean-up procedure. The peptides were eluted by a step gradient from the restricted access column, applying 10 mM phosphate buffer pH 3.5 from 5 to 20% (v/v) of acetonitrile with 1 M NaCl and transferred to a Micra ODS II column (33x4.6 mm). The separation of the peptides and their fragments was performed by a linear gradient from 20 to 60% (v/v) acetonitrile in water with 0.1% formic acid and 0.01% trifluoroacetic acid in 4 min at a flow-rate of 0.75 ml/min. An integrated and completely automated system composed of sample clean up-HPLC-ESI-MS was used to analyze real life samples. The sample volumes ranged between 20 and 100 microl. Peaks due to the fragments NPY 1-36, 3-36 and 13-36 in porcine plasma were identified by ESI-MS. The limit of detection was in the 5 nmol/ml range. The total analysis required 21 min and allowed the direct injection of plasma.

  7. Cation–cation interactions and cation exchange in a series of isostructural framework uranyl tungstates

    SciTech Connect

    Balboni, Enrica; Burns, Peter C.

    2014-05-01

    The isotypical compounds (UO{sub 2}){sub 3}(WO{sub 6})(H{sub 2}O){sub 5} (1), Ag(UO{sub 2}){sub 3}(WO{sub 6})(OH)(H{sub 2}O){sub 3} (2), K(UO{sub 2}){sub 3}(WO{sub 6})OH(H{sub 2}O){sub 4} (3), Rb(UO{sub 2}){sub 3}(WO{sub 6})(OH)(H{sub 2}O){sub 3.5} (4), and Cs(UO{sub 2}){sub 3}(WO{sub 6})OH(H{sub 2}O){sub 3} (5) were synthesized, characterized, and their structures determined. Each crystallizes in space group Cc. (1): a=12.979 (3), b=10.238 (2), c=11.302 (2), β=102.044 (2); (2): a=13.148 (2), b=9.520 (1), c=11.083 (2), β=101.568 (2); (3): a=13.111 (8), b=9.930 (6), c=11.242 (7), β=101.024 (7); (4): a=12.940 (2), b=10.231 (2), c=11.259(2), β=102.205 (2); (5): a=12.983 (3), b=10.191 (3), c=11.263 (4), β=101.661 (4). Compounds 1–5 are a framework of uranyl and tungsten polyhedra containing cation–cation interactions. The framework has three symmetrically distinct U(VI) cations, one tungsten, sixteen to eighteen oxygen atoms, and in 2–5, one monovalent cation. Each atom occupies a general position. Each U(VI) cation is present as a typical (UO{sub 2}){sup 2+} uranyl ion in an overall pentagonal bipyramidal coordination environment. Each pentagonal bipyramid shares two equatorial edges with two other pentagonal bipyramids, forming a trimer. Trimers are connected into chains by edge-sharing with WO{sub 6} octahedra. Chains are linked through cation–cation interactions between two symmetrically independent uranyl ions. This yields a remarkably complex system of intersecting channels that extend along [0 0 1] and [−1 1 0]. The cation exchange properties of 2 and 3 were characterized at room temperature and at 140 °C. - Graphical abstract: Chains of uranium and tungsten polyhedra are connected into a three dimensional framework by cation–cation interactions occurring between two symmetrically independent uranyl pentagonal bipyramids. Monovalent cations present in channels within the structure can be exchanged by room temperature or mild hydrothermal

  8. Phosphonic acid based exchange resins

    DOEpatents

    Horwitz, E.P.; Alexandratos, S.D.; Gatrone, R.C.; Chiarizia, R.

    1995-09-12

    An ion exchange resin is described for extracting metal ions from a liquid waste stream. An ion exchange resin is prepared by copolymerizing a vinylidene diphosphonic acid with styrene, acrylonitrile and divinylbenzene. 10 figs.

  9. Phosphonic acid based exchange resins

    DOEpatents

    Horwitz, E. Philip; Alexandratos, Spiro D.; Gatrone, Ralph C.; Chiarizia, Ronato

    1995-01-01

    An ion exchange resin for extracting metal ions from a liquid waste stream. An ion exchange resin is prepared by copolymerizing a vinylidene diphosphonic acid with styrene, acrylonitrile and divinylbenzene.

  10. Alkaline earth cation extraction from acid solution

    DOEpatents

    Dietz, Mark; Horwitz, E. Philip

    2003-01-01

    An extractant medium for extracting alkaline earth cations from an aqueous acidic sample solution is described as are a method and apparatus for using the same. The separation medium is free of diluent, free-flowing and particulate, and comprises a Crown ether that is a 4,4'(5')[C.sub.4 -C.sub.8 -alkylcyclohexano]18-Crown-6 dispersed on an inert substrate material.

  11. Alloyed Copper Chalcogenide Nanoplatelets via Partial Cation Exchange Reactions

    PubMed Central

    2014-01-01

    We report the synthesis of alloyed quaternary and quinary nanocrystals based on copper chalcogenides, namely, copper zinc selenide–sulfide (CZSeS), copper tin selenide–sulfide (CTSeS), and copper zinc tin selenide–sulfide (CZTSeS) nanoplatelets (NPLs) (∼20 nm wide) with tunable chemical composition. Our synthesis scheme consisted of two facile steps: i.e., the preparation of copper selenide–sulfide (Cu2–xSeyS1–y) platelet shaped nanocrystals via the colloidal route, followed by an in situ cation exchange reaction. During the latter step, the cation exchange proceeded through a partial replacement of copper ions by zinc or/and tin cations, yielding homogeneously alloyed nanocrystals with platelet shape. Overall, the chemical composition of the alloyed nanocrystals can easily be controlled by the amount of precursors that contain cations of interest (e.g., Zn, Sn) to be incorporated/alloyed. We have also optimized the reaction conditions that allow a complete preservation of the size, morphology, and crystal structure as that of the starting Cu2–xSeyS1–y NPLs. The alloyed NPLs were characterized by optical spectroscopy (UV–vis–NIR) and cyclic voltammetry (CV), which demonstrated tunability of their light absorption characteristics as well as their electrochemical band gaps. PMID:25050455

  12. Chromatographic behaviors of proteins on cation-exchange column.

    PubMed

    Li, Rong; Chen, Guo-Liang; Zhao, Wen-Ming

    2004-12-01

    A weak cation-exchanger (XIDACE-WCX) has been synthesized by the indirect method. The chromatographic characteristics of the synthesized packing was studied in detail. The standard protein mixture and lysozyme from egg white were separated with the prepared chromatographic column. The chromatographic thermodynamics of proteins was studied in a wide temperature range. Thermodynamic parameters standard enthalpy change (deltaH0) and standard entropy change (deltaS0) and compensation temperature (beta) at protein denaturation were determined in the chromatographic system. By using obtained deltaS0, the conformational change of proteins was judged in the chromatographic process. The linear relationship between deltaH0 and deltaS0 can be used to identify the identity of the protein retention mechanism in the weak cation-exchange chromatography. The interaction between weak cation-exchanger and metal ions was investigated. Several metal chelate columns were prepared. The effects of introducing metal ion into the naked column on protein retention and the retention mechanism of proteins in the metal chalet affinity chromatography were discussed. PMID:15689030

  13. Lipoic acid functionalized amino acids cationic lipids as gene vectors.

    PubMed

    Su, Rong-Chuan; Liu, Qiang; Yi, Wen-Jing; Zheng, Li-Ting; Zhao, Zhi-Gang

    2016-10-01

    A series of reducible cationic lipids 4a-4f with different amino acid polar-head groups were prepared. The novel lipid contains a hydrophobic lipoic acid (LA) moiety, which can be reduced under reductive conditions to release of the encapsulated plasmid DNA. The particle size, zeta potential and cellular uptake of lipoplexes formed with DNA, as well as the transfection efficacy (TE) were characterized. The TE of the cationic lipid based on arginine was especially high, and was 2.5times higher than that of a branched polyethylenimine in the presence of 10% serum.

  14. Ion-exchange selectivities of periderm and cuticular membranes toward alkali cations

    SciTech Connect

    Ersoz, M.; Duncan, H.J.

    1994-08-01

    The ion-exchange selectivities of lithium, sodium, potassium, and cesium on isolated potato periderm (Solanum tuberosum) and pear fruit cuticular membranes were investigated; the general order of preference both for cation selectivities and ion-exchange capacities was lithium > sodium > potassium > cesium. The potato periderm and pear fruit cuticular membranes exhibited a behavior typical of ion-exchange resins of the weak acid type. At constant pH 7, the ion-exchange capacities of periderm and cuticular membranes increased with hydrated ionic radius, and also with increasing pH and neutral salt concentration, and decreased with crystal ionic radius. Counterion selectivities also exhibited the same behavior. The ion-exchange properties are discussed in terms of the structure and function of potato periderm and pear fruit cuticular membranes.

  15. Alkaline earth metal cation exchange: effect of mobile counterion and dissolved organic matter.

    PubMed

    Indarawis, Katrina; Boyer, Treavor H

    2012-04-17

    The goal of this research was to provide an improved understanding of the interactions between alkaline earth metals and DOM under conditions that are encountered during drinking water treatment with particular focus on cation exchange. Both magnetically enhanced and nonmagnetic cation exchange resins were converted to Na, Mg, Ca, Sr, and Ba mobile counterion forms as a novel approach to investigate the exchange behavior between the cations and the interactions between the cations and DOM. The results show that cation exchange is a robust process for removal of Ca(2+) and Mg(2+) considering competition with cations on the resin surface and presence of DOM. DOM was actively involved during the cation exchange process through complexation, adsorption, and coprecipitation reactions. In addition to advancing the understanding of ion exchange processes for water treatment, the results of this work are applicable to membrane pretreatment to minimize fouling, treatment of membrane concentrate, and precipitative softening.

  16. Exchangeable Cations in the Soils of Quercus Dominated Forests in Northeastern Austria

    NASA Astrophysics Data System (ADS)

    Yan, Shuai; Bruckman, Viktor J.; Glatzel, Gerhard

    2010-05-01

    In northeastern Austria there is a growing interest in increased utilisation of forest biomass for energy. This study focuses on soil properties and nutrient pool characteristics in deciduous forests in order to provide advice for forest management. We (i) quantified selected exchangeable cations in the soils of our study area and (ii) identified the effects of stand age, soil type, soil depth and soil pH on exchangeable cations and cation exchange capacity (CEC). Nine permanent Quercus petraea dominated plots on sandy, clayey cambisols and calcic chernozem were selected for our study. From each plot 18 soil samples were collected in a systematic grid by means of a soil corer with 70 mm diameter to a maximum depth of 60 cm. Soil pH, exchangeable mineral elements K, Ca, Mg, Na, Mn, Al, and Fe were determined in five geometric soil horizons. Statistical analysis showed that (i) forest age did not influence the exchangeable K content of the sandy soils; (ii) the exchangeable K content decreased with increasing stand age in clayey cambisols; (iii) exchangeable K, Na and Mg were higher in calcic chernozems and clayey cambisols (iv) exchangeable Fe was significantly higher in sandy forest soils except in the 60-80 years old stand; (v) exchangeable Fe was below detection limit in calcic chernozem soils. A comparison of exchangeable cations revealed that (i) Ca is the key element of base cations (ii) the content of base cations is strongly significantly higher in calcic chernozem soils (iii) calcic chernozem soils have the highest CEC. CEC ranged from 38 to 190 μmol/g in the entire research area. Base cations, acid cations and CEC differ with soil depth as followed (i) in sandy and clayey cambisols, CEC had a minimum in 20 cm depth and then increased with soil depth to 50 cm; (ii) CEC decreased steadily with soil depth in calcic chernozems. As expected, CEC is significantly positively correlated (Pearson correlation coefficient 0.661, P<0.01) with the pH of the soil. The

  17. Several textural properties of compacted and cation-exchanged bentonite

    NASA Astrophysics Data System (ADS)

    Montes-Hernandez, G.; Duplay, J.; Géraud, Y.; Martinez, L.

    2006-08-01

    One of the principal applications for bentonite is in drilling muds. Moreover it is widely used as a suspending and stabilizing agent, and as an adsorbent or clarifying agent, in many industries. Recently the bentonites have been proposed as engineered barriers for radioactive waste repository because these materials are supposed to build up a better impermeable zone around wastes by swelling. For these reasons, a textural characterization of bentonites in the laboratory is very important. The aim in this study was to estimate several textural properties of compacted and cation-exchanged bentonite by using Hg-porosimetry, N2-adsorption, water vapour adsorption, scanning electron microscopy (SEM) observations and environmental scanning electron microscopy-digital images analysis measurements. For that, bulk samples were mechanically compressed at atmospheric conditions by using a uniaxial system at four different pressures (21, 35, 49, and 63 MPa) in order to obtain four physical densities. On the other hand, the bulk samples of bentonite were treated separately with four concentrated solutions (1N concentration) of sodium, potassium, magnesium and calcium chlorides in order to obtain a homoionic interlayer cation in the clay phase. The results showed that the macro-porosity (porous size>50 nm) and eventually the mesoporosity (porous size 2 50 nm) are affected by the uniaxial compaction. In this case, a transformation of the shape of the macro-pores network from tube to crack was observed. On the other hand, the swelling potential and water content are governed by the relative humidity and by the nature of interlayer cation.

  18. Atomistic understanding of cation exchange in PbS nanocrystals using simulations with pseudoligands

    NASA Astrophysics Data System (ADS)

    Fan, Zhaochuan; Lin, Li-Chiang; Buijs, Wim; Vlugt, Thijs J. H.; van Huis, Marijn A.

    2016-05-01

    Cation exchange is a powerful tool for the synthesis of nanostructures such as core-shell nanocrystals, however, the underlying mechanism is poorly understood. Interactions of cations with ligands and solvent molecules are systematically ignored in simulations. Here, we introduce the concept of pseudoligands to incorporate cation-ligand-solvent interactions in molecular dynamics. This leads to excellent agreement with experimental data on cation exchange of PbS nanocrystals, whereby Pb ions are partially replaced by Cd ions from solution. The temperature and the ligand-type control the exchange rate and equilibrium composition of cations in the nanocrystal. Our simulations reveal that Pb ions are kicked out by exchanged Cd interstitials and migrate through interstitial sites, aided by local relaxations at core-shell interfaces and point defects. We also predict that high-pressure conditions facilitate strongly enhanced cation exchange reactions at elevated temperatures. Our approach is easily extendable to other semiconductor compounds and to other families of nanocrystals.

  19. Impregnating titanium phosphate nanoparticles onto a porous cation exchanger for enhanced lead removal from waters.

    PubMed

    Jia, Kun; Pan, Bingcai; Lv, Lu; Zhang, Qingrui; Wang, Xiaoshu; Pan, Bingjun; Zhang, Weiming

    2009-03-15

    Titanium phosphate (TiP) exhibits preferable sorption toward lead ion in the presence of competing calcium ions at high levels, however, it is present as fine or ultrafine particles and cannot be directly employed in fixed-bed or any flow-through systems due to the excessive pressure drop and poor mechanical strength. In the present study a new hybrid sorbent TiP-001 was fabricated by impregnating titanium phosphate (TiP) nanoparticles onto a strongly acidic cation exchanger D-001 for enhanced lead removal from waters. D-001 was selected as a host material mainly because of the Donnan membrane effect resulting from the immobilized sulfonic acid groups bound on the exchanger matrix, which would enhance permeation of the target metal cation prior to effective sequestration. TiP-001 was characterized by transmission electron micrograph (TEM), X-ray diffraction (XRD), and pH-titration. Batch and column sorption onto TiP-001 was assayed to evaluate its performance as compared to the host exchanger D-001. Lead sorption onto TiP-001 is a pH-dependent process due to the ion-exchange nature, and its sorption kinetics follows the pseudo-second-order model well. Compared to D-001, TiP-001 displays highly selective lead sorption in the presence of competing calcium cations at concentration of several orders higher than the target metal. Fixed-bed sorption of a synthetic feeding solution indicates that lead retention by TiP-001 results in a conspicuous decrease of this toxic metal from 0.50 to below 0.010 mg/L (drinking water standard recommended by WHO). Moreover, its feasible regeneration by dilute HCl solution also favors TiP-001 to be a feasible sorbent for enhanced lead removal from water. PMID:19101673

  20. Cation exchange pretreatment studies for high recovery - Yuma desalting plant

    SciTech Connect

    Kaakinen, J.W.; Laverty, P.E.

    1983-10-01

    The main purpose of the High Recovery Test Program was to obtain feasibility design data for cation exchange softening to allow a greater fractional recovery of desalted product water at the YDP(Yuma Desalting Plant). Compared to the original YDP design with 70-percent desalting recovery, additional removal of calcium in the desalting feed would allow recoveries over 90 percent. Pilot plant equipment to test this process was operated at the YDTF(Yuma Desalting Test Facility) and consisted of an IX unit and an electrodialyzer to supply reject-brine regenerant for the IX experiments. Gypsum scale buildup in the resin bed could be avoided by regeneration with a high upward flow rate causing a fluidized bed. Reuse of regenerant was also beneficial. Results show that the ion exchange high recovery pretreatment process is highly feasible, and that it is technically possible to achieve high recovery in the YDP. Numerous recommendations for a plant design are given and future studies are noted.

  1. Destruction of gel sulfonated cation-exchangers of the KU-2 type under the influence of hydrogen peroxide

    SciTech Connect

    Roginskaya, B.S.; Zavadovskaya, A.S.; Znamenskii, Yu.P.; Paskhina, N.A.; Dobrova, E.I.

    1988-10-20

    The purpose of this work was to study the mechanism of interaction of Soviet sulfonated cation-exchangers of the KU-2 type with hydrogen peroxide. It is shown that under the influence of hydrogen peroxide sulfonated cation-exchangers begin, after a certain induction period, to lose capacity and to release destruction products into water; the length of the induction period increases with the degree of cross-linking. In a given time of contact between the resin and the solution the degree of destruction falls with increase of cross-linking. The principal product of destruction of sulfonated cation-exchangers is an aromatic sulfonic acid containing oxidized groups in the side chains.

  2. Computer simulation of displacement cation exchange chromatography: separation of trivalent actinides and lanthanides

    SciTech Connect

    Forsberg, C.W.

    1980-05-01

    A first-generation mathematical model of displacement cation exchange chromatography (CES) was constructed. The model incorporated the following phenomena: diffusion of cations up and down the column, diffusion of cations from the bulk liquid to the resin surface, and equilibrium of cations between liquid and solid resin beads. A limited number of experiments with rare earths using DTPA as the separation agent were undertaken to increase the current understanding of the processes involved in cation exchange chromatography. The numerical computer program based on the mathematical model was written in FORTRAN IV for use on the IBM 360 series of computers.

  3. Enhanced DOC removal using anion and cation ion exchange resins.

    PubMed

    Arias-Paic, Miguel; Cawley, Kaelin M; Byg, Steve; Rosario-Ortiz, Fernando L

    2016-01-01

    Hardness and DOC removal in a single ion exchange unit operation allows for less infrastructure, is advantageous for process operation and depending on the water source, could enhance anion exchange resin removal of dissolved organic carbon (DOC). Simultaneous application of cationic (Plus) and anionic (MIEX) ion exchange resin in a single contact vessel was tested at pilot and bench scales, under multiple regeneration cycles. Hardness removal correlated with theoretical predictions; where measured hardness was between 88 and 98% of the predicted value. Comparing bench scale DOC removal of solely treating water with MIEX compared to Plus and MIEX treated water showed an enhanced DOC removal, where removal was increased from 0.5 to 1.25 mg/L for the simultaneous resin application compared to solely applying MIEX resin. A full scale MIEX treatment plant (14.5 MGD) reduced raw water DOC from 13.7 mg/L to 4.90 mg/L in the treated effluent at a bed volume (BV) treatment rate of 800, where a parallel operation of a simultaneous MIEX and Plus resin pilot (10 gpm) measured effluent DOC concentrations of no greater than 3.4 mg/L, even at bed volumes of treatment 37.5% greater than the full scale plant. MIEX effluent compared to simultaneous Plus and MIEX effluent resulted in differences in fluorescence intensity that correlated to decreases in DOC concentration. The simultaneous treatment of Plus and MIEX resin produced water with predominantly microbial character, indicating the enhanced DOC removal was principally due to increased removal of terrestrially derived organic matter. The addition of Plus resin to a process train with MIEX resin allows for one treatment process to remove both DOC and hardness, where a single brine waste stream can be sent to sewer at a full-scale plant, completely removing lime chemical addition and sludge waste disposal for precipitative softening processes. PMID:26624231

  4. Influence of pine bark particle size and pH on cation exchange capacity

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cation exchange capacity (CEC) describes the maximum quantity of cations a soil or substrate can hold while being exchangeable with the soil solution. While CEC has been studied for peat-based substrates, relatively little work has documented factors that affect CEC of pine bark substrates. The ob...

  5. Reactive transport modeling of multicomponent cation exchange at the laboratory and field scale

    SciTech Connect

    Steefel, Carl I.

    2004-04-01

    Multicomponent ion exchange models have been successful in describing the chromatographic separation of cations in both laboratory and field settings. Their chief advantage lies in their ability to capture the competitive effects of other cations that may be present. By incorporating exchanger activity coefficients calculated on the basis of the Gibbs-Duhem equation applied to the exchanger phase, it is possible to correct for the non-ideality of exchange. The use of multiple exchange sites can also substantially improve the ability of the cation exchange models to describe adsorption and retardation. All of these benefits are associated with relatively little additional computational burden. Even where the cost of the multicomponent cation exchange calculations are considered too high, the models are useful in calculating distribution coefficients for the environmental conditions of interest.

  6. Incorporation of phthalocyanines by cationic and anionic clays via ion exchange and direct synthesis

    SciTech Connect

    Carrado, K.A.; Botto, R.E.; Winans, R.E. ); Forman, J.E. )

    1993-04-01

    Phthalocyanines (Pc) and metallophthalocyanines were incorporated into the galleries of anionic and cationic clays via ion exchange and in situ crystallization of the synthetic clay layers. Intercalation compounds between the layered magnesium silicate clay hectorite and cationic phthalocyanines were directly prepared by refluxing for 2 days aqueous solutions of silica sol, magnesium hydroxide, lithium flouride, and either alcian blue dyes (Cu(II)Pc) or 15-crown-5 tetra-substituted phthalocyanine (15C5Pc). The CuPc dyes are tetrapositively charged through peripheral quaternary ammonium groups, whereas the 15C5Pc is electrically neutral. Anionic clays prepared by hydrolysis of mixed solutions of aluminum nitrate, magnesium nitrate, and copper(II) phthalocyaninetetrasulfonic acid, tetrasodium salt (CuPcTs) in sodium hydroxide resulted in crystallization of an intercalation compound between a layered double hydroxide (LDH) and this anionic Pc. The material prepared by ion exchange of CuPcTs into a wet, freshly prepared LDH was superior in crystallinity. The phthalocyanines are oriented parallel to cationic hectorite clay layers (gallery heights 4.5-6.5[angstrom]) and perpendicular to anionic layered double hydroxide clay layers (gallery height 18,2[angstrom]) in correlation with their hosts' respective layer charge densities. 32 refs., 4 figs., 2 tabs.

  7. Thermodynamic parameters of cation exchange in MOF-5 and MFU-4l.

    PubMed

    Brozek, Carl K; Dincă, Mircea

    2015-07-28

    We present a method for approximating thermodynamic parameters ΔG(P,T)°, ΔH, and ΔS for the cation exchange process in metal-organic frameworks, as exemplified by Ni(2+) exchange into Zn4O(1,4-benzenedicarboxylate)3 (MOF-5) and Co(2+) exchange into MOF-5 and Zn5Cl4(bis(1H-1,2,3-triazolo-[4,5-b],[4',5'-i])dibenzo-[1,4]-dioxin)3 (MFU-4l). For these examples, we find that the cation exchange process is endergonic and that parameters such as solvent and cation identity impact the thermodynamics.

  8. Determination of magnesium in alumina ceramics by atomic absorption spectrometry after separation by cation exchange chromatography

    SciTech Connect

    van der Walt, T.N.; Strelow, F.W.E.

    1985-12-01

    A method is presented for the determination of traces of magnesium in alumina ceramics. After dissolution in an orthophosphoric acid-sulfuric acid mixture the magnesium is separated from the large excess of aluminum by cation exchange chromatography, using a 4% cross-linked resin and 0.50 M oxalic acid as eluting agent. Magnesium is finally determined by atomic absorption spectrometry using an acetylene-nitrous oxide flame. By use of Suprapur reagents and beakers made of Teflon, contamination can be reduced to ca. 2..mu..g with a variation between multiple blank runs of ca. 0.4 ..mu..g. About 3 ppm of magnesium in 1-g samples can be determined with approximately the same variation while larger amounts of magnesium (200-300 ppm in the alumina ceramics) show a variation of only +/- 1 ppm. 12 references, 1 table.

  9. Annealed perfluorinated cation exchange polymers for corrosion resistant coatings

    SciTech Connect

    Kinlen, P.J.; Silverman, D.C. )

    1993-11-01

    Casting and annealing a perfluorinated cation exchange (Nafion) polymer onto aluminum or 316SS results in a system which inhibits pitting and crevice corrosion that normally occurs in the presence of chloride ions and dissolved oxygen. This inhibition is believed to results from the unique chloride ion rejection properties of the annealed Nafion coating. Under neutral and basic conditions (pH > 5), localized corrosion is suppressed. Potentiodynamic polarization scans of the annealed Nafion coated aluminum and 316SS positive to the potential of the bare electrode does not produce pits. Electrochemical impedance results show that corrosion is unchanged after the coated alloy has been polarized above the pitting potential. In addition, the electrochemical impedance results indicate that the electrical resistance of the coating is low, hardly increasing the uncompensated resistance above that found for the bare metal. Hence, the movement of water and positive ions through the coating is unhindered Long-term stability and long-term corrosion inhibition afforded by the polymer must still be assessed to determine the practical limits of applicability of this coating system.

  10. Adsorption of reovirus to clay minerals: effects of cation-exchange capacity, cation saturation, and surface area.

    PubMed Central

    Lipson, S M; Stotzky, G

    1983-01-01

    The adsorption of reovirus to clay minerals has been reported by several investigators, but the mechanisms defining this association have been studied only minimally. The purpose of this investigation was to elucidate the mechanisms involved with this interaction. More reovirus type 3 was adsorbed, in both distilled and synthetic estuarine water, by low concentrations of montmorillonite than by comparable concentrations of kaolinite containing a mixed complement of cations on the exchange complex. Adsorption to the clays was essentially immediate and was correlated with the cation-exchange capacity of the clays, indicating that adsorption was primarily to negatively charged sites on the clays. Adsorption was greater with low concentrations of clays in estuarine water than in distilled water, as the higher ionic strength of the estuarine water reduced the electrokinetic potential of both clay and virus particles. The addition of cations (as chloride salts) to distilled water enhanced adsorption, with divalent cations being more effective than monovalent cations and 10(-2) M resulting in more adsorption than 10(-3) M. Potassium ions suppressed reovirus adsorption to montmorillonite, probably by collapsing the clay lattices and preventing the expression of the interlayer-derived cation-exchange capacity. More virus was adsorbed by montmorillonite made homoionic to various mono-, di-, and trivalent cations (except by montmorillonite homoionic to potassium) than by comparable concentrations of kaolinite homoionic to the same cations. The sequence of the amount of adsorption to homoionic montmorillonite was Al greater than Ca greater than Mg greater than Na greater than K; the sequence of adsorption to kaolinite was Na greater than Al greater than Ca greater than Mg greater than K. The constant partition-type adsorption isotherms obtained when the clay concentration was maintained constant and the virus concentration was varied indicated that a fixed proportion of the

  11. Bovine whey fractionation based on cation-exchange chromatography.

    PubMed

    Hahn, R; Schulz, P M; Schaupp, C; Jungbauer, A

    1998-02-01

    Bovine whey proteins have potential applications in veterinary medicine, food industry and as supplements for cell culture media. A fractionation scheme for the economically interesting proteins, such as IgG, lactoferrin and lactoperoxidase, based on cation exchangers was the goal of our investigations. A chromatographic process was developed where alpha-lactalbumin passes through the column and separation of the desired proteins is achieved. Four different cation-exchange media (S-HyperD-F, S-Sepharose FF, Fractogel EMD SO3- 650 (S) and Macro-Prep High S Support) were compared in regard to their dynamic binding capacity for IgG and their different elution behaviours when sequential step gradients with NaCl buffers were applied. Peak fractions were analyzed by size-exclusion chromatography and sodium dodecyl sulphate-polyacrylamide gel electrophoresis. Lactoperoxidase activity was monitored by the oxidation of o-phenylenediamine. In order to explain the different resolution behaviours, isocratic runs with pure standards of whey proteins were performed. The k' values were calculated and plotted against salt concentration. Fractogel EMD had the highest binding capacity for IgG, 3.7 mg/ml gel at a linear flow-rate of 100 cm/h, but the resolution was low compared to that with the other three media. S-Hyper D and S-Sepharose FF showed lower capacities, 3.3 and 3.2 mg/ml gel, respectively, but exhibited better protein resolution. These effects could be partially explained by the k' versus salt concentration plots. The binding capacity of Macro-Prep S was considerably lower compared to that of the other resins investigated because its selectivity for whey proteins was completely different. S-Sepharose FF and S-Hyper D combine relatively high dynamic capacity for IgG and good resolution. Compared to studies with standard proteins, such as 100 mg/ml bovine serum albumin for S-Hyper D, their binding capacities were very low. Even after removal of low-molecular-mass compounds

  12. Preparation of decarboxylic-functionalized weak cation exchanger and application for simultaneous separation of alkali, alkaline earth and transition metals.

    PubMed

    Peng, Yahui; Gan, Yihui; He, Chengxia; Yang, Bingcheng; Guo, Zhimou; Liang, Xinmiao

    2016-06-01

    A novel weak cation exchanger (WCX) with dicarboxyl groups functionalized has been developed by clicking mercaptosuccinic acid onto silica gel. The simple synthesis starts with modification of silica gel with triethoxyvinylsilane, followed by efficient coupling vinyl-bonded silica with mercaptosuccinic acid via a "thiol-ene" click reaction. The obtained WCX demonstrated good separation and high selectivity towards common metals. Simultaneous separation of 10 alkali, alkaline earth and transition metals was achieved within 12min. Ion exchange and complex mechanism dominates the separation process. Its utility was demonstrated for determination of metals in tap water. PMID:27130093

  13. Determining the cation exchange capacity of montmorillonite by simultaneous thermal analysis method

    NASA Astrophysics Data System (ADS)

    Boeva, N. M.; Bocharnikova, Yu. I.; Belousov, P. E.; Zhigarev, V. V.

    2016-08-01

    A way of determining the cation exchange capacity of montmorillonite by simultaneous thermal analysis is developed using as an example the bentonites of the 10th Khutor deposit (Republic of Khakassia) and the Vodopadnyi area (Sakhalin Island). A correlation is established between the cation exchange capacity of smectite and its weight loss upon heating in the range of dehydration; the enthalpy of dehydration of montmorillonite; and the weight loss and the enthalpy of thermal dissociation of ethylene glycol contained in the interlayer space of the mineral's crystal structure. These data open up new possibilities for determining the cation exchange capacity of montmorillonite, the most important technological indicator of the natural clay nanomineral.

  14. Black Carbon Increases Cation Exchange Capcity in Soils

    SciTech Connect

    Liang,B.; Lehmann, J.; Solomon, D.; Kinyangi, J.; Grossman, J.; ONeill, B.; Skjemstad, J.; Thies, J.; Luizao, F.; et al.

    2006-01-01

    Black Carbon (BC) may significantly affect nutrient retention and play a key role in a wide range of biogeochemical processes in soils, especially for nutrient cycling. Anthrosols from the Brazilian Amazon (ages between 600 and 8700 yr BP) with high contents of biomass-derived BC had greater potential cation exchange capacity (CEC measured at pH 7) per unit organic C than adjacent soils with low BC contents. Synchrotron-based near edge X-ray absorption fine structure (NEXAFS) spectroscopy coupled with scanning transmission X-ray microscopy (STXM) techniques explained the source of the higher surface charge of BC compared with non-BC by mapping cross-sectional areas of BC particles with diameters of 10 to 50 {micro}m for C forms. The largest cross-sectional areas consisted of highly aromatic or only slightly oxidized organic C most likely originating from the BC itself with a characteristic peak at 286.1 eV, which could not be found in humic substance extracts, bacteria or fungi. Oxidation significantly increased from the core of BC particles to their surfaces as shown by the ratio of carboxyl-C/aromatic-C. Spotted and non-continuous distribution patterns of highly oxidized C functional groups with distinctly different chemical signatures on BC particle surfaces (peak shift at 286.1 eV to a higher energy of 286.7 eV) indicated that non-BC may be adsorbed on the surfaces of BC particles creating highly oxidized surface. As a consequence of both oxidation of the BC particles themselves and adsorption of organic matter to BC surfaces, the charge density (potential CEC per unit surface area) was greater in BC-rich Anthrosols than adjacent soils. Additionally, a high specific surface area was attributable to the presence of BC, which may contribute to the high CEC found in soils that are rich in BC.

  15. Cation Exchange Selectivity versus concentration of competing heavy metal cations (Pb2+,Zn2+) : case of Na-montmorillonite

    NASA Astrophysics Data System (ADS)

    Oueslati, W.; Mefath, M.; Ben Rhaiem, H.; Ben Haj Amara, A.

    2009-11-01

    Cation Exchange Selectivity (CES) for Wyoming montmorillonite was determined by equilibration of the clay with a mixed equinormal solution containing two competing cations (i.e. Pb2+, Zn2+). This paper aims at characterizing the structural change and selectivity of a Na-dioctahedral smectite (Wy-Na). The quantitative analysis of XRD patterns is achieved using an indirect method based on the comparison of XRD experimental patterns to calculated ones. Two reference samples were prepared by saturation with Pb2+ or Zn2+ (i.e. two heavy metal cations occurring in hold house trash). The resulting complexes were respectively labelled Wy-Pb and Wy-Zn. After that, the Wy-Na sample was dispersed in solutions containing 0.5Pb2+ and 0.5Zn2+ with different concentrations (from 10-2 N to 10-4 N) in order to understand the concentration effect on the selectivity process of the Na-montmorillonite. The XRD quantitative analysis shows that for low concentrations the d001 spacing value corresponds to Wy-Na complex, whereas for high concentrations the d001 spacing value can be attributed to the Wy-Zn and/or Wy-Pb. At low concentrations, the sample presents a homogeneous state and the cation exchange capacity is saturated with Na+ cation which is characterized by one water layer hydration state (1W). For high concentrations, interstratified hydration behavior appears and the clay has a tendency to exchange in minor contribution the Zn2+ cation and in major contribution Pb2+ cation characterized by a mixed hydration state between one (1W) and two water layers (2W).

  16. From Light Impurity Doping to Complete Cation Exchange in Semiconductor Nanocrystals: The Role of Coulomb Interactions

    NASA Astrophysics Data System (ADS)

    Erwin, Steven; Ott, Florian; Norris, David

    2014-03-01

    Cation exchange is a reversible chemical reaction used to create new materials by replacing one type of cation with another, usually from solution. We have developed an atomistic model describing cation exchange in semiconductor nanocrystals. The model uses a small set of results obtained from DFT calculations for Ag-doped CdSe. From these we constructed a kinetic Monte Carlo model to address finite temperatures and time scales beyond the reach of DFT. Our simulations span a wide range of Ag concentrations, from light doping to full cation exchange. Thus our model provides a single conceptual framework in which these two phenomena can be understood as limiting endpoints. The results of the simulations are consistent with several experimentally observed aspects of both phenomena. An unexpected finding of our simulations is that the Coulomb interaction plays a central, but changing, role as the Ag concentration varies from light doping to fully cation exchanged. For example, if the Coulomb interaction is strongly screened then cation exchange is suppressed or stopped. When only moderately screened, Coulomb effects play an unanticipated but important role for both doping and cation exchange.

  17. Adsorption of paraquat on soil organic matter: effect of exchangeable cations and dissolved organic carbon.

    PubMed

    Gondar, Dora; López, Rocío; Antelo, Juan; Fiol, Sarah; Arce, Florencio

    2012-10-15

    Herbicides that interact with soil organic matter do so with both the solid and the dissolved fractions, so that the distribution of herbicide between the soil solution and solid phases is determined by competitive effects. In the present study, adsorption experiments were carried out with the cationic herbicide paraquat and untreated and acid-washed samples of a peat soil, at different values of pH and ionic strength. Less herbicide was adsorbed onto the untreated peat than onto the acid-washed peat; the difference was due to the presence of exchangeable cations, as demonstrated in experiments carried out by adding Ca(2+) to suspensions of acid-washed peat. The results were interpreted by an electrostatic model and the fitting parameters indicated that the adsorption constants were the same for both samples of peat, although the number of binding sites available was different. Simultaneous resolution of the adsorption equilibrium of paraquat for the soil organic matter (SOM) and of the binding equilibrium between paraquat and dissolved organic matter (DOM) enabled the distribution of paraquat between the solid and solution phases to be determined. The increased solubility of the SOM with increasing pH led to a decrease in the fraction of paraquat retained on the peat surface above pH 5.5, which favors the mobility of the herbicide in the soil.

  18. Preparation and characterization of high capacity, strong cation-exchange fiber based adsorbents.

    PubMed

    Schwellenbach, Jan; Taft, Florian; Villain, Louis; Strube, Jochen

    2016-05-20

    Motivated by the demand for more economical capture and polishing steps in downstream processing of protein therapeutics, a novel strong cation-exchange chromatography stationary phase based on polyethylene terephthalate (PET) high surface area short-cut fibers is presented. The fiber surface is modified by grafting glycidyl methacrylate (GMA) via surface-initiated atom transfer radical polymerization (SI-ATRP) and a subsequent derivatization leading to sulfonic acid groups. The obtained cation-exchange fibers have been characterized and compared to commercially available resin and membrane based adsorbers. High volumetric static binding capacities for lysozyme (90mg/mL) and polyclonal human IgG (hIgG, 92mg/mL) were found, suggesting an efficient multi-layer binding within the grafted hydrogel layer. A packed bed of randomly orientated fibers has been tested for packing efficiency, permeability and chromatographic performance. High dynamic binding capacities for lysozyme (50mg/mL) and hIgG (54mg/mL) were found nearly independent of the bed-residence time, revealing a fast mass-transport mechanism. Height equivalent to a theoretical plate (HETP) values in the order of 0.1 cm and a peak asymmetry factor (AF) of 1.8 have been determined by tracer experiments. Additionally inverse size-exclusion chromatography (iSEC) revealed a bimodal structure within the fiber bed, consisting of larger transport channels, formed by the voidage between the fibers, and a hydrogel layer with porous properties. PMID:27106396

  19. Infrared Spectroscopic Investigation on CH Bond Acidity in Cationic Alkanes

    NASA Astrophysics Data System (ADS)

    Matsuda, Yoshiyuki; Xie, Min; Fujii, Asuka

    2016-06-01

    We have demonstrated large enhancements of CH bond acidities in alcohol, ether, and amine cations through infrared predissociation spectroscopy based on the vacuum ultraviolet photoionization detection. In this study, we investigate for the cationic alkanes (pentane, hexane, and heptane) with different alkyl chain lengths. The σ electrons are ejected in the ionization of alkanes, while nonbonding electrons are ejected in ionization of alcohols, ethers, and amines. Nevertheless, the acidity enhancements of CH in these cationic alkanes have also been demonstrated by infrared spectroscopy. The correlations of their CH bond acidities with the alkyl chain lengths as well as the mechanisms of their acidity enhancements will be discussed by comparison of infrared spectra and theoretical calculations.

  20. Aspects of the super-equivalent sorption of glycine by cation exchanger KU-2-8

    NASA Astrophysics Data System (ADS)

    Khokhlova, O. N.; Khokhlov, V. Yu.; Trunaeva, E. S.; Nechaeva, L. S.

    2016-07-01

    The structure formed in a sorbent during the super-equivalent sorption of glycine by cation exchanger KU-2-8 is optimized via quantum chemical simulation. The differential thermodynamic characteristics of ion exchange and super-equivalent sorption in the studied system are calculated using a thermodynamic approach that allows us to describe the simultaneous exchange and super-equivalent sorption of compounds by ion-exchangers.

  1. Phenolic cation exchange resin material for recovery of cesium and strontium

    DOEpatents

    Ebra, Martha A.; Wallace, Richard M.

    1983-01-01

    A phenolic cation exchange resin with a chelating group has been prepared by reacting resorcinol with iminodiacetic acid in the presence of formaldehyde at a molar ratio of about 1:1:6. The material is highly selective for the simultaneous recovery of both cesium and strontium from aqueous alkaline solutions, such as, aqueous alkaline nuclear waste solutions. The organic resins are condensation polymers of resorcinol and formaldehyde with attached chelating groups. The column performance of the resins compares favorably with that of commercially available resins for either cesium or strontium removal. By combining Cs.sup.+ and Sr.sup.2+ removal in the same bed, the resins allow significant reduction of the size and complexity of facilities for processing nuclear waste.

  2. Phenolic cation-exchange resin material for recovery of cesium and strontium. [Patent application

    DOEpatents

    Ebra, M.A.; Wallace, R.M.

    1982-05-05

    A phenolic cation exchange resin with a chelating group has been prepared by reacting resorcinol with iminodiacetic acid in the presence of formaldehyde at a molar ratio of about 1:1:6. The material is highly selective for the simultaneous recovery of both cesium and strontium from aqueous alkaline solutions, such as, aqueous alkaline nuclear wate solutions. The organic resins are condensation polymers of resorcinol and formaldehyde with attached chelating groups. The column performance of the resins compares favorably with that of commercially available resins for either cesium or strontium removal. By combining Cs/sup +/ and Sr/sup 2 +/ removal in the same bed, the resins allow significant reduction of the size and complexity of facilities for processing nuclear waste.

  3. Controlled methyl-esterification of pectin catalyzed by cation exchange resin.

    PubMed

    Peng, Xiaoxia; Yang, Guang; Fan, Xingchen; Bai, Yeming; Ren, Xiaomeng; Zhou, Yifa

    2016-02-10

    This study developed a new method to methyl-esterify pectin using a cation exchange resin. Homogalacturonan (HG)-type pectin (WGPA-3-HG) and rhamnogalacturonan (RG)-I-type pectin (AHP-RG) obtained from the roots of Panax ginseng and sunflower heads, respectively, were used as models. Compared to commonly used methyl-esterification methods that use either methyl iodide or acidified methanol, the developed method can methyl-esterify both HG- and RG-I-type pectins without degrading their structures via β-elimination or acid hydrolysis. In addition, by modifying reaction conditions, including the mass ratio of resin to pectin, reaction time, and temperature, the degree of esterification can be controlled. Moreover, the resin and methanol can be recycled to conserve resources, lower costs, and reduce environmental pollution. This new methodology will be highly useful for industrial esterification of pectin. PMID:26686175

  4. Analytical solutions for flow in porous media with multicomponent cation exchange reactions

    NASA Astrophysics Data System (ADS)

    Venkatraman, Ashwin; Hesse, Marc A.; Lake, Larry W.; Johns, Russell T.

    2014-07-01

    Multicomponent cation exchange reactions have important applications in groundwater remediation, disposal of nuclear wastes as well as enhanced oil recovery. The hyperbolic theory of conservation laws can be used to explain the nature of displacements observed during flow with cation exchange reactions between flowing aqueous phase and stationary solid phase. Analytical solutions have been developed to predict the effluent profiles for a particular case of heterovalent cations (Na+, Ca2+ and Mg2+) and an anion (Cl-) for any combination of constant injection and constant initial composition using this theory. We assume local equilibrium, neglect dispersion and model the displacement as a Riemann problem using mass action laws, the charge conservation equation and the cation exchange capacity equation. The theoretical predictions have been compared with experimental data available at two scales—the laboratory scale and the field scale. The theory agrees well with the experimental data at both scales. Analytical theory predictions show good agreement with numerical model, developed using finite differences.

  5. Atomistic understanding of cation exchange in PbS nanocrystals using simulations with pseudoligands

    PubMed Central

    Fan, Zhaochuan; Lin, Li-Chiang; Buijs, Wim; Vlugt, Thijs J. H.; van Huis, Marijn A.

    2016-01-01

    Cation exchange is a powerful tool for the synthesis of nanostructures such as core–shell nanocrystals, however, the underlying mechanism is poorly understood. Interactions of cations with ligands and solvent molecules are systematically ignored in simulations. Here, we introduce the concept of pseudoligands to incorporate cation-ligand-solvent interactions in molecular dynamics. This leads to excellent agreement with experimental data on cation exchange of PbS nanocrystals, whereby Pb ions are partially replaced by Cd ions from solution. The temperature and the ligand-type control the exchange rate and equilibrium composition of cations in the nanocrystal. Our simulations reveal that Pb ions are kicked out by exchanged Cd interstitials and migrate through interstitial sites, aided by local relaxations at core–shell interfaces and point defects. We also predict that high-pressure conditions facilitate strongly enhanced cation exchange reactions at elevated temperatures. Our approach is easily extendable to other semiconductor compounds and to other families of nanocrystals. PMID:27160371

  6. Separation of traces and large amounts of lead from gram amounts of bismuth, tin, cadmium, and indium by cation exchange chromatography in hydrochloric acid - methanol using a macroporous resin

    SciTech Connect

    Strelow, F.W.E.

    1985-10-01

    Traces and small amounts of lead can be separated from gram amounts of Bi, Sn, Cd, and In by eluting these elements with 0.5 M HCl in 50% methanol from a column containing only 2.7 mL (1g) of Bio-Rad AG MP-50 macroporous cation exchange resin of 100-200 mesh particle size in the H form. A 5.4 mL (2 g) resin column separates up to 100 mg of lead. Lead can be eluted effectively with 3.0 M aqueous HCl. Separations are sharp and quantitative. In combination with flame atomic absorption spectrometry, the method has been applied for the determination of lead in pure metals or chemicals of the above elements. Relative standard deviations were better than 1% for samples containing 10 ppm of lead or more. The sensitivity is less than 0.1 ppm. Relevant elution curves and results of analyses of binary synthetic mixtures and actual samples are presented. 7 references, 4 figures, 2 tables.

  7. Elution of Re-188 from W-188/Re-188 generators with salts of weak acids permits efficient concentration to low volumes using a new tandem cation/anion exchange system

    SciTech Connect

    Guhlke, S. |; Beets, A.L.; Knapp, F.F. Jr.

    1997-05-01

    Re-188, available from a W-188/Re-188 generator, is an important therapeutic radioisotope for bone pain palliation, cancer therapy and intravascular brachytherapy, etc. Because of the relatively low specific activity of reactor-produced W-188 (ORNL HFIR, 296-370 MBq mCi/mg W-186 for 2 cycles), methods of concentrating the Re-188 bolus (10-12 mL) from clinical scale (18.5-37 BGq W-188) generators (5-6 gm alumina) are thus very important. We demonstrate for the first time a new strategy of generator elution with salts of weak acids and specific perrhenate anion {open_quotes}trapping{close_quotes} with QMA anion columns. Re-188 perrhenate is efficiently eluted (65-75%) from the alumina-based generator with 0.15-0.3 M ammonium acetate. An acetic acid solution of Re-188 perrhenic acid is obtained by subsequent on-line passage of the generator eluant through a DOWEX AG 50Wx8 (200-400 mesh, H{sup +} form) column. Since acetic acid is not ionized (< 0.001%) at this pH (< pK{sub a} = 4.76) the perrhenate anion is then specifically trapped on a QMA {open_quotes}Light{close_quotes} anion extraction column. QMA elution with 0.9% NaCl, provides Re-188 perrhenate solution in <1 mL. Concentration of 10-20 mL of Re-188 solution (> 15 BGq) in <1 mL has been demonstrated using this simple new approach, which is also effective for concentration of Tc-99m from low specific activity Mo-99 (n,y) generators. The cation/anion tandem system is inexpensive and disposable and use can be easily automated. The availability of this very simple, efficient system is important for broad use of rhenium-188.

  8. Phosphonic acid based ion exchange resins

    DOEpatents

    Horwitz, E.P.; Alexandratos, S.D.; Gatrone, R.C.; Chiarizia, R.

    1994-01-25

    An ion exchange resin is described for extracting metal ions from a liquid waste stream. An ion exchange resin is prepared by copolymerizing a vinylidene diphosphonic acid with styrene, acrylonitrile and divinylbenzene. 9 figures.

  9. Phosphonic acid based ion exchange resins

    DOEpatents

    Horwitz, E.P.; Alexandratos, S.D.; Gatrone, R.C.; Chiarizia, R.

    1996-07-23

    An ion exchange resin is described for extracting metal ions from a liquid waste stream. An ion exchange resin is prepared by copolymerizing a vinylidene diphosphonic acid with styrene, acrylonitrile and divinylbenzene. 10 figs.

  10. Phosphonic acid based ion exchange resins

    DOEpatents

    Horwitz, E. Philip; Alexandratos, Spiro D.; Gatrone, Ralph C.; Chiarizia, Ronato

    1994-01-01

    An ion exchange resin for extracting metal ions from a liquid waste stream. An ion exchange resin is prepared by copolymerizing a vinylidene disphosphonic acid with styrene, acrylonitrile and divinylbenzene.

  11. Phosphonic acid based ion exchange resins

    DOEpatents

    Horwitz, E. Philip; Alexandratos, Spiro D.; Gatrone, Ralph C.; Chiarizia, Ronato

    1996-01-01

    An ion exchange resin for extracting metal ions from a liquid waste stream. An ion exchange resin is prepared by copolymerizing a vinylidene diphosphonic acid with styrene, acrylonitrile and divinylbenzene.

  12. Tuning the Magnetic Properties of Metal Oxide Nanocrystal Heterostructures by Cation Exchange

    PubMed Central

    2013-01-01

    For three types of colloidal magnetic nanocrystals, we demonstrate that postsynthetic cation exchange enables tuning of the nanocrystal’s magnetic properties and achieving characteristics not obtainable by conventional synthetic routes. While the cation exchange procedure, performed in solution phase approach, was restricted so far to chalcogenide based semiconductor nanocrystals, here ferrite-based nanocrystals were subjected to a Fe2+ to Co2+ cation exchange procedure. This allows tracing of the compositional modifications by systematic and detailed magnetic characterization. In homogeneous magnetite nanocrystals and in gold/magnetite core shell nanocrystals the cation exchange increases the coercivity field, the remanence magnetization, as well as the superparamagnetic blocking temperature. For core/shell nanoheterostructures a selective doping of either the shell or predominantly of the core with Co2+ is demonstrated. By applying the cation exchange to FeO/CoFe2O4 core/shell nanocrystals the Neél temperature of the core material is increased and exchange-bias effects are enhanced so that vertical shifts of the hysteresis loops are obtained which are superior to those in any other system. PMID:23362940

  13. Equilibrium Model for Ion Exchange Between Multivalent Cations and Zeolite-A in a Molten Salt

    SciTech Connect

    Supathorn Phongikaroon; Michael Simpson

    2005-10-01

    A two-site equilibrium model that previously only accommodated monovalent cations has been extended to include divalent and trivalent cations for ion exchange between zeolite-A and molten chloride salts, a process being considered for concentrating nuclear fission products into high level waste forms. Equilibrium constants were determined by fitting the model to equilibrium data sets for ion exchange between zeolite-A and Cs ternary salt (CsCl-LiCl-KCl), Rb ternary salt (RbCl-LiCl-KCl), Na ternary salt (NaCl-LiCl-KCl), Sr ternary salt (SrCl2-LiCl-KCl), and U ternary salt (UCl3-LiCl-KCl). The results reveal a good fit between the experimental data sets and the model. The two ion exchange sites, framework sites and occluded sites, demonstrate different relative selectivities for the cations. It was found that Sr2_ is the preferred cation in the ion exchange site, and Cs_ is the preferred cation in the occlusion site. Meanwhile, Li_ has the highest combined selectivity when both ion exchange and occlusion sites are considered. Interestingly, divalent and trivalent species are more preferred in the ion exchange site than the monovalent species with the exception of Li_.

  14. Effect of Sulfuric and Triflic Acids on the Hydration of Vanadium Cations: An ab Initio Study.

    PubMed

    Sepehr, Fatemeh; Paddison, Stephen J

    2015-06-01

    Vanadium redox flow batteries (VRFBs) may be a promising solution for large-scale energy storage applications, but the crossover of any of the redox active species V(2+), V(3+), VO(2+), and VO2(+) through the ion exchange membrane will result in self-discharge of the battery. Hence, a molecular level understanding of the states of vanadium cations in the highly acidic environment of a VRFB is needed. We examine the effects of sulfuric and triflic (CF3SO3H) acids on the hydration of vanadium species as they mimic the electrolyte and functional group of perfluorosulfonic acid (PFSA) membranes. Hybrid density functional theory in conjunction with a continuum solvation model was utilized to obtain the local structures of the hydrated vanadium cations in proximity to H2SO4, CF3SO3H, and their conjugate anions. The results indicate that none of these species covalently bond to the vanadium cations. The hydration structure of V(3+) is more distorted than that of V(2+) in an acidic medium. The oxo-group of VO2(+) is protonated by either acid, in contrast to VO(2+) which is not protonated. The atomic partial charge of the four oxidation states of vanadium varies from +1.7 to +2.0. These results provide the local solvation structures of vanadium cations in the VRFBs environment that are directly related to the electrolytes stability and diffusion of vanadium ions into the membrane. PMID:25954916

  15. Effect of Sulfuric and Triflic Acids on the Hydration of Vanadium Cations: An ab Initio Study.

    PubMed

    Sepehr, Fatemeh; Paddison, Stephen J

    2015-06-01

    Vanadium redox flow batteries (VRFBs) may be a promising solution for large-scale energy storage applications, but the crossover of any of the redox active species V(2+), V(3+), VO(2+), and VO2(+) through the ion exchange membrane will result in self-discharge of the battery. Hence, a molecular level understanding of the states of vanadium cations in the highly acidic environment of a VRFB is needed. We examine the effects of sulfuric and triflic (CF3SO3H) acids on the hydration of vanadium species as they mimic the electrolyte and functional group of perfluorosulfonic acid (PFSA) membranes. Hybrid density functional theory in conjunction with a continuum solvation model was utilized to obtain the local structures of the hydrated vanadium cations in proximity to H2SO4, CF3SO3H, and their conjugate anions. The results indicate that none of these species covalently bond to the vanadium cations. The hydration structure of V(3+) is more distorted than that of V(2+) in an acidic medium. The oxo-group of VO2(+) is protonated by either acid, in contrast to VO(2+) which is not protonated. The atomic partial charge of the four oxidation states of vanadium varies from +1.7 to +2.0. These results provide the local solvation structures of vanadium cations in the VRFBs environment that are directly related to the electrolytes stability and diffusion of vanadium ions into the membrane.

  16. Mixed-mode reversed-phase and ion-exchange separations of cationic analytes on polybutadiene-coated zirconia.

    PubMed

    Hu, Yue; Yang, Xiqin; Carr, Peter W

    2002-08-30

    The retention and selectivity of the chromatographic separation of basic (cationic) analytes on a polybutadiene-coated zirconia (PBD-ZrO2) stationary phase have been studied in greater detail than in previous studies. These separations are strongly influenced by the chemistry of the accessible surface of zirconia. In the presence of buffers which contain hard Lewis bases (e.g., phosphate, fluoride, carboxylic acids) zirconia's surface becomes negatively charged due to adsorption of the buffer anion at the hard Lewis acid sites. Consequently, under most conditions (e.g., neutral pH), cationic analytes undergo both hydrophobic and cation-exchange interactions. This mixed-mode retention process generally leads to greater retention factors for cations relative to those on silica-based reversed phases despite the lower surface areas of the zirconia phase, but, more importantly, adsorption of hard Lewis bases can be used to control the chromatographic selectivity for cationic analytes on these zirconia-based stationary phases. In contrast to our prior work, here we show that when mixed-mode retention takes place, both retention and selectivity are easily adjusted by changing the type of hard Lewis base buffer anion, the type of buffer counter-ion (e.g., sodium, potassium, ammonium), the pH, and the ionic strength of the eluent as well as the type and amount of organic modifier. PMID:12236500

  17. Cation exchange at the secondary building units of metal-organic frameworks.

    PubMed

    Brozek, C K; Dincă, M

    2014-08-21

    Cation exchange is an emerging synthetic route for modifying the secondary building units (SBUs) of metal-organic frameworks (MOFs). This technique has been used extensively to enhance the properties of nanocrystals and molecules, but the extent of its applications for MOFs is still expanding. To harness cation exchange as a rational tool, we need to elucidate its governing factors. Not nearly enough experimental observations exist for drawing these conclusions, so we provide a conceptual framework for approaching this task. We address which SBUs undergo exchange, why certain ions replace others, how the framework influences the process, the role of the solvent, and current applications. Using these guidelines, certain trends emerge from the available data and missing experiments become obvious. If future studies follow this framework, then a more comprehensive body of observations will furnish a deeper understanding of cation exchange and inspire future applications.

  18. A weak cation-exchange monolith as stationary phase for the separation of peptide diastereomers by CEC.

    PubMed

    Ludewig, Ronny; Nietzsche, Sandor; Scriba, Gerhard K E

    2011-01-01

    A CEC weak cation-exchange monolith has been prepared by in situ polymerization of acrylamide, methylenebisacrylamide and 4-acrylamidobutyric acid in a decanol-dimethylsulfoxide mixture as porogen. The columns were evaluated by SEM and characterized with regard to the separation of diastereomers and α/β-isomers of aspartyl peptides. Column preparation was reproducible as evidenced by comparison of the analyte retention times of several columns prepared simultaneously. Analyte separation was achieved using mobile phases consisting of acidic phosphate buffer and ACN. Under these conditions the peptides migrated due to their electrophoretic mobility but the EOF also contributed as driving force as a function of the pH of the mobile phase due to increasing dissociation of the carboxyl groups of the polymer. Raising the pH of the mobile phase also resulted in deprotonation of the peptides reducing analyte mobility. Due to these mechanisms each pair of diastereomeric peptides displayed the highest resolution at a different pH of the buffer component of the mobile phase. Comparing the weak-cation exchange monolith to an RP monolith and a strong cation-exchange monolith different elution order of some peptide diastereomers was observed, clearly illustrating that interactions with the stationary phase contribute to the CEC separations.

  19. Charge exchange of a polar molecule at its cation

    SciTech Connect

    Buslov, E. Yu. Zon, B. A.

    2011-01-15

    The Landau-Herring method is used to derive an analytic expression for the one-electron exchange interaction of a polar molecule with its positively charged ion, induced by a {sigma}-electron. Analogously to the classical Van der Pole method, the exchange interaction potential is averaged over the rotational states of colliding particles. The resonant charge-transfer cross section is calculated, and the effect of the dipole moments of the core on the cross section is analyzed. It is shown that allowance for the dependence of the exchange potential on the orientation of the dipole moments relative to the molecular axis may change the dependence of the cross section on the velocity of colliding particles, which is typical of the resonant charge exchange, from the resonance to the quasi-resonance dependence.

  20. Mechanism of protodesorption-exchange of heavy metal cations for protons in a heterophase system of H2O-H2SO4-MSO4-cellulose sorbent.

    PubMed

    Kozlov, V A; Nikiforova, T E; Loginova, V A; Koifman, O I

    2015-12-15

    The influence of pH on the distribution of metal cations [Cd(II), Cu(II), Fe(II), Ni(II), Zn(II)] in a four-component heterophase system (H2O-H2SO4-MSO4-cellulose sorbent) was studied. Protodesorption of metal cations was studied with indicator and constant quantities of [MSO4] salts and constant solvent-sorbent ratio. Linear dependence lgКDМ2+=f(рН) with tgα=1/2 of the КDМ2+ metal ions distribution coefficients from the acidity of the aqueous phase is observed in logarithmic coordinates. Depression of the exponent corresponding to proton involvement in protodesorption from 2 (theory) to 0.5 (experiment) indicates that anions of the aqueous phase are involved in the process of exchange of metal cation for proton on the anionic centers of the sorbent, which corresponds to participation of the salt and acid components of the system in molecular non-dissociated form in an equivalent proportion H2SO4/MSO4=1/1. Different behavior of the salt and acid components in ion exchange of cations for cations and cations for protons is due to the differences in the constraint coefficients of their molecular and ionic forms which must be taken into consideration in equations describing thermodynamics of the interphase exchange.

  1. Ion chromatographic separation of inorganic ions using a combination of hydrophilic interaction chromatographic column and cation-exchange resin column.

    PubMed

    Arai, Kaori; Mori, Masanobu; Hironaga, Takahiro; Itabashi, Hideyuki; Tanaka, Kazuhiko

    2012-04-01

    A combination of hydrophilic interaction chromatographic (HILIC) column and a weakly acidic cation-exchange resin (WCX) column was used for simultaneous separation of inorganic anions and cations by ion chromatography (IC). Firstly, the capability of HILIC column for the separation of analyte ions was evaluated under acidic eluent conditions. The columns used were SeQuant ZIC-HILIC (ZIC-HILIC) with a sulfobetaine-zwitterion stationary phase (ZIC-HILIC) and Acclaim HILIC-10 with a diol stationary phase (HILIC-10). When using tartaric acid as the eluent, the HILIC columns indicated strong retentions for anions, based on ion-pair interaction. Especially, HILIC-10 could strongly retain anions compared with ZIC-HILIC. The selectivity for analyte anions of HILIC-10 with 5 mmol/L tartaric acid eluent was in the order of I(-) > NO3(-) > Br(-) > Cl(-) > H2PO4(-). However, since HILIC-10 could not separate analyte cations, a WCX column (TSKgel Super IC-A/C) was connected after the HILIC column in series. The combination column system of HILIC and WCX columns could successfully separate ten ions (Na+, NH4+, K+, Mg2+, Ca2+, H2PO4(-), Cl(-), Br(-), NO3(-) and I(-)) with elution of 4 mmol/L tartaric acid plus 8 mmol/L 18-crown-6. The relative standard deviations (RSDs) of analyte ions by the system were in the ranges of 0.02% - 0.05% in retention times and 0.18% - 5.3% in peak areas through three-time successive injections. The limits of detection at signal-to-noise ratio of 3 were 0.24 - 0.30 micromol/L for the cations and 0.31 - 1.2 micromol/L for the anions. This system was applied for the simultaneous determination of the cations and the anions in a vegetable juice sample with satisfactory results.

  2. Synthesis and adsorption properties of the cation exchange forms of OFF-type zeolite

    NASA Astrophysics Data System (ADS)

    Gorshunova, K. K.; Travkina, O. S.; Kustov, L. M.; Kutepov, B. I.

    2016-03-01

    The possibility of the ion-exchange of Na+ and K+ cations contained in OFF-type zeolite for H+, Ni2+, Cu2+, Co2+, and La3+ cations is investigated. Chemical and phase compositions, the morphology of crystals, and the adsorption properties of synthesized samples are studied via X-ray fluorescence and X-ray diffraction analysis, IR spectroscopy, scanning electron microscopy, and adsorption measurements.

  3. Cation exchange in a glacial till drumlin at a road salt storage facility.

    PubMed

    Ostendorf, David W; Xing, Baoshan; Kallergis, Niki

    2009-05-12

    We use laboratory and field data to calibrate existing geochemical and transport models of cation exchange induced by contamination of an unconfined aquifer at a road salt storage facility built upon a glacial till drumlin in eastern Massachusetts. A Gaines and Thomas selectivity coefficient K models the equilibrium sodium and divalent cation distribution in the groundwater and solid matrix, while an existing method of characteristics model describes the advective transport of total dissolved cations and sorbed sodium. Laboratory isotherms of split spoon soil samples from the drumlin calibrate K with an average value of 0.0048 (L/g)(1/2) for a measured cation exchange capacity of 0.057 meq/g dry soil. Ten years of monitoring well data document groundwater flow and the advection of conservative chloride due to outdoor storage and handling of road salt at the site. The monitoring well cation data and retarded transport model offer an independent K calibration of 0.0040 to 0.0047 (L/g)(1/2): the consistency of the field and laboratory selectivity coefficient calibrations endorse this application of the Gaines and Thomas and method of characteristics models. The advancing deicing agent plume releases divalent cations from the till into the groundwater, so that monitoring well samples do not reflect the chemical composition of the road salt. In this regard, dissolved divalent cation milliequivalent concentrations are as high as 80% of the total dissolved cationic concentrations in the salt contaminated monitoring well samples, far greater than their 2.5% level in the road salt stored at the site. Cation exchange can thus obscure attempts to hindcast stored road salt sodium water table concentration from monitoring well sample stoichiometry, or to predict sodium impacts on groundwater or receiving stream quality downgradient of the well.

  4. Cation exchange in a glacial till drumlin at a road salt storage facility

    NASA Astrophysics Data System (ADS)

    Ostendorf, David W.; Xing, Baoshan; Kallergis, Niki

    2009-05-01

    We use laboratory and field data to calibrate existing geochemical and transport models of cation exchange induced by contamination of an unconfined aquifer at a road salt storage facility built upon a glacial till drumlin in eastern Massachusetts. A Gaines and Thomas selectivity coefficient K models the equilibrium sodium and divalent cation distribution in the groundwater and solid matrix, while an existing method of characteristics model describes the advective transport of total dissolved cations and sorbed sodium. Laboratory isotherms of split spoon soil samples from the drumlin calibrate K with an average value of 0.0048 (L/g) 1/2 for a measured cation exchange capacity of 0.057 meq/g dry soil. Ten years of monitoring well data document groundwater flow and the advection of conservative chloride due to outdoor storage and handling of road salt at the site. The monitoring well cation data and retarded transport model offer an independent K calibration of 0.0040 to 0.0047 (L/g) 1/2: the consistency of the field and laboratory selectivity coefficient calibrations endorse this application of the Gaines and Thomas and method of characteristics models. The advancing deicing agent plume releases divalent cations from the till into the groundwater, so that monitoring well samples do not reflect the chemical composition of the road salt. In this regard, dissolved divalent cation milliequivalent concentrations are as high as 80% of the total dissolved cationic concentrations in the salt contaminated monitoring well samples, far greater than their 2.5% level in the road salt stored at the site. Cation exchange can thus obscure attempts to hindcast stored road salt sodium water table concentration from monitoring well sample stoichiometry, or to predict sodium impacts on groundwater or receiving stream quality downgradient of the well.

  5. Exchangeable cations-mediated photodegradation of polycyclic aromatic hydrocarbons (PAHs) on smectite surface under visible light.

    PubMed

    Jia, Hanzhong; Li, Li; Chen, Hongxia; Zhao, Yue; Li, Xiyou; Wang, Chuanyi

    2015-04-28

    Clay minerals saturated with different exchangeable cations are expected to play various roles in photodegradation of polycyclic aromatic hydrocarbons (PAHs) via direct and/or indirect pathways on clay surfaces. In the present study, anthracene and phenanthrene were selected as molecule probes to investigate the roles of exchangeable cations on their photodegradation under visible light irradiation. For five types of cation-modified smectite clays, the photodegradation rate of anthracene and phenanthrene follows the order: Fe(3+)>Al(3+)>Cu(2+)>Ca(2+)>K(+)>Na(+), which is consistent with the binding energy of cation-π interactions between PAHs and exchangeable cations. The result suggests that PAHs photolysis rate depends on cation-π interactions on clay surfaces. Meanwhile, the deposition of anthracene at the Na(+)-smectite and K(+)-smectite surface favors solar light absorption, resulting in enhanced direct photodecomposition of PAHs. On the other hand, smectite clays saturated with Fe(3+), Al(3+), and Cu(2+) are highly photoreactive and can act as potential catalysts giving rise to oxidative radicals such as O2(-) , which initiate the transformation of PAHs. The present work provides valuable insights into understanding the transformation and fate of PAHs in the natural soil environment and sheds light on the development of technologies for contaminated land remediation. PMID:25621830

  6. Exchangeable cations-mediated photodegradation of polycyclic aromatic hydrocarbons (PAHs) on smectite surface under visible light.

    PubMed

    Jia, Hanzhong; Li, Li; Chen, Hongxia; Zhao, Yue; Li, Xiyou; Wang, Chuanyi

    2015-04-28

    Clay minerals saturated with different exchangeable cations are expected to play various roles in photodegradation of polycyclic aromatic hydrocarbons (PAHs) via direct and/or indirect pathways on clay surfaces. In the present study, anthracene and phenanthrene were selected as molecule probes to investigate the roles of exchangeable cations on their photodegradation under visible light irradiation. For five types of cation-modified smectite clays, the photodegradation rate of anthracene and phenanthrene follows the order: Fe(3+)>Al(3+)>Cu(2+)>Ca(2+)>K(+)>Na(+), which is consistent with the binding energy of cation-π interactions between PAHs and exchangeable cations. The result suggests that PAHs photolysis rate depends on cation-π interactions on clay surfaces. Meanwhile, the deposition of anthracene at the Na(+)-smectite and K(+)-smectite surface favors solar light absorption, resulting in enhanced direct photodecomposition of PAHs. On the other hand, smectite clays saturated with Fe(3+), Al(3+), and Cu(2+) are highly photoreactive and can act as potential catalysts giving rise to oxidative radicals such as O2(-) , which initiate the transformation of PAHs. The present work provides valuable insights into understanding the transformation and fate of PAHs in the natural soil environment and sheds light on the development of technologies for contaminated land remediation.

  7. [Determination of soil exchangeable base cations by using atomic absorption spectrophotometer and extraction with ammonium acetate].

    PubMed

    Zhang, Yu-ge; Xiao, Min; Dong, Yi-hua; Jiang, Yong

    2012-08-01

    A method to determine soil exchangeable calcium (Ca), magnesium (Mg), potassium (K), and sodium (Na) by using atomic absorption spectrophotometer (AAS) and extraction with ammonium acetate was developed. Results showed that the accuracy of exchangeable base cation data with AAS method fits well with the national standard referential soil data. The relative errors for parallel samples of exchangeable Ca and Mg with 66 pair samples ranged from 0.02%-3.14% and 0.06%-4.06%, and averaged to be 1.22% and 1.25%, respectively. The relative errors for exchangeable K and Na with AAS and flame photometer (FP) ranged from 0.06%-8.39% and 0.06-1.54, and averaged to be 3.72% and 0.56%, respectively. A case study showed that the determination method for exchangeable base cations by using AAS was proven to be reliable and trustable, which could reflect the real situation of soil cation exchange properties in farmlands. PMID:23156790

  8. Contributions of acid deposition and natural processes to cation leaching from forest soils: a review

    SciTech Connect

    Johnson, D.W.; Van Miegroet, H.; Cole, D.W.; Richter, D.D.

    1983-01-01

    Methods of quantifying the roles of atmospheric acid inputs and internal acid generation by carbonic, organic, and nitric acids are illustrated by reviewing data sets from several intensively studied sites in North America. Some of the sites (tropical, Costa Rica (La Selva); temperate deciduous, Tennessee (Walker Branch); and temperate coniferous, Washington (Thompson)) received acid precipitation whereas others (northern, southeast Alaska (Petersburg); and subalpine, Washington Cascades (Findley Lake)) did not. Natural leaching by carbonic acid dominated soil leaching in the tropical and temperate coniferous sites, nitric acid (caused by nitrification) dominated leaching in an N-fixing temperate deciduous site (red alder in Washington), and organic acids dominated surface soil leaching in the subalpine site and contributed to leaching of surface soils in several other sites. Only at the temperate deciduous sites in eastern Tennessee did atmospheric acid input play a major role in soil leaching. In no case, however, are the annual net losses of cations regarded as alarming as compared to soil exchangeable cation capital.

  9. Assessment of cation trapping by cellular acidic compartments.

    PubMed

    Marceau, François; Roy, Caroline; Bouthillier, Johanne

    2014-01-01

    All nucleated cells, from yeast to animal cells, concentrate cationic chemicals (weak bases with a pKa~8-10) into acidic cell compartments (low retro-diffusion under a protonated form at low pH=ion trapping). The proton pump vacuolar (V)-ATPase is the driving force of this pseudotransport that concerns acidic organelles (mainly late endosomes and lysosomes). The latter rapidly become swollen (osmotic vacuolization) and macroautophagic. Cation concentration in cells is not proved to involve membrane transporters, but is prevented or reversed by inhibitors of V-ATPase, such as bafilomycin A1. Lipophilicity is a major determinant of the apparent affinity of this pseudotransport because simple diffusion of the uncharged form supports it. Quinacrine is a formerly used antiparasitic drug that is intensely fluorescent, lipophilic, and a tertiary amine. The drug, at micromolar concentrations, is proposed as a superior probe for assessing cation trapping by cellular acidic compartments, being readily quantified using fluorometry in cell extracts and analyzed using microscopy and cytofluorometry (fluorescence settings for fluorescein being applicable). Further, cells respond to micromolar levels of quinacrine by autophagic accumulation (e.g., accumulation of the activated macroautophagic effector LC3 II, immunoblots), an objective and universal response to sequestered amines.

  10. Impact of sediment-seawater cation exchange on Himalayan chemical weathering fluxes

    NASA Astrophysics Data System (ADS)

    Lupker, Maarten; France-Lanord, Christian; Lartiges, Bruno

    2016-08-01

    Continental-scale chemical weathering budgets are commonly assessed based on the flux of dissolved elements carried by large rivers to the oceans. However, the interaction between sediments and seawater in estuaries can lead to additional cation exchange fluxes that have been very poorly constrained so far. We constrained the magnitude of cation exchange fluxes from the Ganga-Brahmaputra river system based on cation exchange capacity (CEC) measurements of riverine sediments. CEC values of sediments are variable throughout the river water column as a result of hydrological sorting of minerals with depth that control grain sizes and surface area. The average CEC of the integrated sediment load of the Ganga-Brahmaputra is estimated ca. 6.5 meq 100 g-1. The cationic charge of sediments in the river is dominated by bivalent ions Ca2+ (76 %) and Mg2+ (16 %) followed by monovalent K+ (6 %) and Na+ (2 %), and the relative proportion of these ions is constant among all samples and both rivers. Assuming a total exchange of exchangeable Ca2+ for marine Na+ yields a maximal additional Ca2+ flux of 28 × 109 mol yr-1 of calcium to the ocean, which represents an increase of ca. 6 % of the actual river dissolved Ca2+ flux. In the more likely event that only a fraction of the adsorbed riverine Ca2+ is exchanged, not only for marine Na+ but also Mg2+ and K+, estuarine cation exchange for the Ganga-Brahmaputra is responsible for an additional Ca2+ flux of 23 × 109 mol yr-1, while ca. 27 × 109 mol yr-1 of Na+, 8 × 109 mol yr-1 of Mg2+ and 4 × 109 mol yr-1 of K+ are re-absorbed in the estuaries. This represents an additional riverine Ca2+ flux to the ocean of 5 % compared to the measured dissolved flux. About 15 % of the dissolved Na+ flux, 8 % of the dissolved K+ flux and 4 % of the Mg2+ are reabsorbed by the sediments in the estuaries. The impact of estuarine sediment-seawater cation exchange appears to be limited when evaluated in the context of the long-term carbon cycle and

  11. DEMINERALIZER BUILDING, TRA608. CATION AND ANION EXCHANGERS LINE UP ALONG ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DEMINERALIZER BUILDING, TRA-608. CATION AND ANION EXCHANGERS LINE UP ALONG NORTH WALL ON CONCRETE PLATFORMS. INL NEGATIVE NO. 2527. Unknown Photographer, 6/12/1951 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

  12. Exchangeable Cation Hydration Properties Strongly Influence Soil Sorption of Nitroaromatic Compounds

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Nitroaromatic compounds (NACs) are commonly found as soil contaminants in military training sites and manufacturing facilities, and may adversely affect human and ecosystem health. Exchangeable cation effects on p-nitrocyanobenzene (p-NCB) and 1,4-dinitrobenzene (1,4-DNB) sorption by the Webster soi...

  13. Calcium Solubility and Cation Exchange Properties in Zeoponic Soil

    NASA Technical Reports Server (NTRS)

    Beiersdorfer, Raymond E.

    1999-01-01

    An important aspect of a regenerative life support system at a Lunar or Martian outpost is the ability to produce food. Essential plant nutrients, as well as a solid support substrate, can be provided by: (1) treated Lunar or Martian regolith; (2) a synthetic soil or (3) some combination of both. A synthetic soil composed of ammonium- and potassium-saturated chinoptlolite (a zeolite mineral) and apatite, can provide slow-release fertilization of plants via dissolution and ion-exchange reactions. Previous equilibrium studies (Beiersdorfer, 1997) on mixtures of synthetic hydroxyapatite and saturated-clinoptilolite indicate that the concentrations of macro-nutrients such as ammonium, phosphorous, potassium, magnesium, and calcium are a function of the ratio of chinoptilolite to apatite in the sample and to the ratio of potassium to ammonium on the exchange sites in the clinoptilolite. Potassium, ammonium, phosphorous, and magnesium are available to plants at sufficient levels. However, calcium is deficient, due to the high degree of calcium adsorption by the clinoptilolite. Based on a series of batch-equilibration experiments, this calcium deficiency can be reduced by (1) treating the clinoptilolite with CaNO3 or (2) adding a second Ca-bearing mineral (calcite, dolomite or wollastonite) to the soil. Treating the Cp with CaNO3 results in increased Ca in solution, decreased P in solution and decreased NH4 in solution. Concentrations of K were not effected by the CaNO3 treatment. Additions of Cal, Dol and Wol changed the concentrations of Ca and P in solution in a systematic fashion. Cal has the greatest effect, Dol the least and Wol is intermediate. The changes are consistent with changes expected for a common ion effect with Ca. Higher concentrations of Ca in solution with added Cal, Dol or Wol do not result in changes in K or NH4 concentrations.

  14. Acidic deposition, cation mobilization, and biochemical indicators of stress in healthy red spruce

    USGS Publications Warehouse

    Shortle, W.C.; Smith, K.T.; Minocha, R.; Lawrence, G.B.; David, M.B.

    1997-01-01

    Dendrochemical and biochemical markers link stress in apparently healthy red spruce trees (Picea rubens) to acidic deposition. Acidic deposition to spruce forests of the northeastern USA increased sharply during the 1960s. Previous reports related visible damage of trees at high elevations to root and soil processes. In this report, dendrochemical and foliar biochemical markers indicate perturbations in biological processes in healthy red spruce trees across the northeastern USA. Previous research on the dendrochemistry of red spruce stemwood indicated that under uniform environmental conditions, stemwood concentrations of Ca and Mg decreased with increasing radial distance from the pith. For nine forest locations, frequency analysis shows that 28 and 52% of samples of red spruce stemwood formed in the 1960s are enriched in Ca and Mg, respectively, relative to wood formed prior to and after the 1960s. This enrichment in trees throughout the northeastern USA may be interpretable as a signal of increased availability of essential cations in forest soils. Such a temporary increase in the availability of Ca and Mg could be caused by cation mobilization, a consequence of increased acidic deposition. During cation mobilization, essential Ca and Mg as well as potentially harmful Al become more available for interaction with binding sites in the soil and absorbing roots. As conditions which favor cation mobilization continue, Ca and Mg can be leached or displaced from the soil. A measure of the interaction between Ca and Al is the Al/Ca binding ratio (molar charge ratio of exchangeable Al to exchangeable Ca). As the Al/Ca binding ratio in the root zone increased from 0.3 to 1.9, the foliar concentration of the biochemical stress marker putrescine also increased from 45 to 145 nm g-1. The correlation of the putrescine concentration to the Al/Ca binding ratio (adj. r2 = 0.68, P < 0.027) suggests that foliar stress may be linked to soil chemistry.

  15. Structure-Property Relationships in Hydroxide-Exchange Membranes with Cation Strings and High Ion-Exchange Capacity.

    PubMed

    Wang, Junhua; Gu, Shuang; Xiong, Ruichang; Zhang, Bingzi; Xu, Bingjun; Yan, Yushan

    2015-12-21

    A series of poly(2,4-dimethyl-1,4-phenylene oxide) hydroxide-exchange membranes (HEMs) with cation strings containing a well-defined number of cations (CS-n) and similar, high ion-exchange capacities are synthesized to investigate the effect of cation distribution on key HEM properties. As the number of cations on each string grows, the size of the ionic clusters increases from 10 to 55 nm. Well-connected ion pathways and a hydrophobic framework are observed for n≥4. The enhanced phase segregation increases the hydroxide conductivity from CS-1 to CS-6 (30 to 65 mS cm(-1) ) and suppresses the water uptake (from 143 % to 62 %). Moreover, molar hydroxide conductivities for CS-n membranes show two distinctive stages as n increases: ∼23 S cm(2)  mol(-1) for n≤3; and ∼34 cm(2)  mol(-1) for n≥4.

  16. Surface-orientation-dependent distribution of subsurface cation-exchange defects in olivine-phosphate nanocrystals.

    PubMed

    Chung, Sung-Yoon; Choi, Si-Young; Kim, Tae-Hwan; Lee, Seongsu

    2015-01-27

    Atomic-scale exchange between two different cations of similar size in crystalline oxides is one of the major types of point defects when multiple cations in oxygen interstitials are arrayed in an ordered manner. Although a number of studies have been performed on a variety of Li-intercalation olivine phosphates to determine the distribution of exchange defects in bulk, understanding of the thermodynamic stability of the defects in subsurface regions and its dependency on the crystallographic orientation at the surface has remained elusive. Through a combination of small-angle neutron scattering, atomic-scale direct probing with scanning transmission electron microscopy, and theoretical ab initio calculations, we directly demonstrate that the antisite exchange defects are distributed in a highly anisotropic manner near the surfaces of LiFePO4 crystals. Moreover, a substantial amount of cation exchanges between Li and Fe sites is identified as an energetically favorable configuration in some surface regions, showing excellent agreement with the calculation results of negative defect formation energies. The findings in this study provide insight into developing better ways to avoid degradation of lithium mobility through the surface as well as scientifically notable features regarding the distribution of exchange defects in olivine phosphates.

  17. Elimination and exchange of trifluoroacetate counter-ion from cationic peptides: a critical evaluation of different approaches.

    PubMed

    Roux, Stéphane; Zékri, Elisabeth; Rousseau, Bernard; Paternostre, Maïté; Cintrat, Jean-Christophe; Fay, Nicolas

    2008-03-01

    Most synthesized peptides are nowadays produced using solid-phase procedures. Due to cleavage and purification conditions, they are mainly obtained in the presence of trifluoroacetic acid (TFA) and, for cationic peptides, as trifluoroacetate (TF-acetate) salts. However, TF-acetate interferes with physicochemical characterizations using infrared spectroscopy and might significantly affect the in vivo studies. Thus, TF-acetate exchange by another counter-ion is often required. Up to now, the classical procedure has consisted of freeze-drying the peptide several times in the presence of an excess of a stronger acid than TFA (pKa approximately 0): generally HCl (pKa = - 7). This approach means that working at pH < 1 can induce peptide degradation. We therefore tested three different approaches to exchange the tightly bound TF-acetate counter-ion from the dicationic octapeptide lanreotide: (i) reverse-phase HPLC, (ii) ion-exchange resin, and (iii) deprotonation/reprotonation cycle of the amino groups. The first two approaches allow the partial to almost complete exchange of the TF-acetate counter-ion by another ion from an acid weaker than TFA, such as acetic acid (pKa = 4.5), and the third requires a basic solution that permits the complete removal of TF-acetate counter-ion. The efficiency of these three procedures was tested and compared by using different analytical techniques such as 19F-NMR, 1H-NMR and attenuated total reflectance Fourier transformed infrared spectroscopy (ATR FT-IR). We also show that ATR-IR can be used to monitor the TFA removal. The counter-ion exchange procedures described in this study are easy to carry out, fast, harmless and reproducible. Moreover, two of them offer the very interesting possibility of exchanging the initial TF-acetate by any other counter-ion. PMID:18035848

  18. First principles derived, transferable force fields for CO2 adsorption in Na-exchanged cationic zeolites.

    PubMed

    Fang, Hanjun; Kamakoti, Preeti; Ravikovitch, Peter I; Aronson, Matthew; Paur, Charanjit; Sholl, David S

    2013-08-21

    The development of accurate force fields is vital for predicting adsorption in porous materials. Previously, we introduced a first principles-based transferable force field for CO2 adsorption in siliceous zeolites (Fang et al., J. Phys. Chem. C, 2012, 116, 10692). In this study, we extend our approach to CO2 adsorption in cationic zeolites which possess more complex structures. Na-exchanged zeolites are chosen for demonstrating the approach. These methods account for several structural complexities including Al distribution, cation positions and cation mobility, all of which are important for predicting adsorption. The simulation results are validated with high-resolution experimental measurements of isotherms and microcalorimetric heats of adsorption on well-characterized materials. The choice of first-principles method has a significant influence on the ability of force fields to accurately describe CO2-zeolite interactions. The PBE-D2 derived force field, which performed well for CO2 adsorption in siliceous zeolites, does not do so for Na-exchanged zeolites; the PBE-D2 method overestimates CO2 adsorption energies on multi-cation sites that are common in cationic zeolites with low Si/Al ratios. In contrast, a force field derived from the DFT/CC method performed well. Agreement was obtained between simulation and experiment not only for LTA-4A on which the force field fitting is based, but for other two common adsorbents, NaX and NaY.

  19. New salts of amino acids with dimeric cations

    NASA Astrophysics Data System (ADS)

    Ghazaryan, V. V.; Fleck, M.; Petrosyan, A. M.

    2010-10-01

    Among salts of amino acids there are compounds with the composition 2A..HX, which consist of dimeric A...A+ cations with short symmetric or asymmetric hydrogen bonds between zwitter-ionic and protonated moieties. These species are materials liable to undergo phase transitions or possess interesting nonlinear optical properties. Here, we report the preparation of 20 new salts with dimeric cations from aqueous solutions, including compounds of glycine, betaine, β- alanine, L-alanine, L-phenylalanine, L-threonine, L-valine, L-leucine and L-proline, with BF4-, ClO4-, Cl-, Br-, HSeO3-, and HC2O4-; as anions. The prepared salts are characterized by IR and Raman spectroscopy. Some of them are grown in form of good quality single crystals, which allowed the determination of their crystal structure.

  20. Influence of the Ion Coordination Number on Cation Exchange Reactions with Copper Telluride Nanocrystals.

    PubMed

    Tu, Renyong; Xie, Yi; Bertoni, Giovanni; Lak, Aidin; Gaspari, Roberto; Rapallo, Arnaldo; Cavalli, Andrea; Trizio, Luca De; Manna, Liberato

    2016-06-01

    Cu2-xTe nanocubes were used as starting seeds to access metal telluride nanocrystals by cation exchanges at room temperature. The coordination number of the entering cations was found to play an important role in dictating the reaction pathways. The exchanges with tetrahedrally coordinated cations (i.e., with coordination number 4), such as Cd(2+) or Hg(2+), yielded monocrystalline CdTe or HgTe nanocrystals with Cu2-xTe/CdTe or Cu2-xTe/HgTe Janus-like heterostructures as intermediates. The formation of Janus-like architectures was attributed to the high diffusion rate of the relatively small tetrahedrally coordinated cations, which could rapidly diffuse in the Cu2-xTe NCs and nucleate the CdTe (or HgTe) phase in a preferred region of the host structure. Also, with both Cd(2+) and Hg(2+) ions the exchange led to wurtzite CdTe and HgTe phases rather than the more stable zinc-blende ones, indicating that the anion framework of the starting Cu2-xTe particles could be more easily deformed to match the anion framework of the metastable wurtzite structures. As hexagonal HgTe had never been reported to date, this represents another case of metastable new phases that can only be accessed by cation exchange. On the other hand, the exchanges involving octahedrally coordinated ions (i.e., with coordination number 6), such as Pb(2+) or Sn(2+), yielded rock-salt polycrystalline PbTe or SnTe nanocrystals with Cu2-xTe@PbTe or Cu2-xTe@SnTe core@shell architectures at the early stages of the exchange process. In this case, the octahedrally coordinated ions are probably too large to diffuse easily through the Cu2-xTe structure: their limited diffusion rate restricts their initial reaction to the surface of the nanocrystals, where cation exchange is initiated unselectively, leading to core@shell architectures. Interestingly, these heterostructures were found to be metastable as they evolved to stable Janus-like architectures if annealed at 200 °C under vacuum. PMID:27177274

  1. Influence of the Ion Coordination Number on Cation Exchange Reactions with Copper Telluride Nanocrystals.

    PubMed

    Tu, Renyong; Xie, Yi; Bertoni, Giovanni; Lak, Aidin; Gaspari, Roberto; Rapallo, Arnaldo; Cavalli, Andrea; Trizio, Luca De; Manna, Liberato

    2016-06-01

    Cu2-xTe nanocubes were used as starting seeds to access metal telluride nanocrystals by cation exchanges at room temperature. The coordination number of the entering cations was found to play an important role in dictating the reaction pathways. The exchanges with tetrahedrally coordinated cations (i.e., with coordination number 4), such as Cd(2+) or Hg(2+), yielded monocrystalline CdTe or HgTe nanocrystals with Cu2-xTe/CdTe or Cu2-xTe/HgTe Janus-like heterostructures as intermediates. The formation of Janus-like architectures was attributed to the high diffusion rate of the relatively small tetrahedrally coordinated cations, which could rapidly diffuse in the Cu2-xTe NCs and nucleate the CdTe (or HgTe) phase in a preferred region of the host structure. Also, with both Cd(2+) and Hg(2+) ions the exchange led to wurtzite CdTe and HgTe phases rather than the more stable zinc-blende ones, indicating that the anion framework of the starting Cu2-xTe particles could be more easily deformed to match the anion framework of the metastable wurtzite structures. As hexagonal HgTe had never been reported to date, this represents another case of metastable new phases that can only be accessed by cation exchange. On the other hand, the exchanges involving octahedrally coordinated ions (i.e., with coordination number 6), such as Pb(2+) or Sn(2+), yielded rock-salt polycrystalline PbTe or SnTe nanocrystals with Cu2-xTe@PbTe or Cu2-xTe@SnTe core@shell architectures at the early stages of the exchange process. In this case, the octahedrally coordinated ions are probably too large to diffuse easily through the Cu2-xTe structure: their limited diffusion rate restricts their initial reaction to the surface of the nanocrystals, where cation exchange is initiated unselectively, leading to core@shell architectures. Interestingly, these heterostructures were found to be metastable as they evolved to stable Janus-like architectures if annealed at 200 °C under vacuum.

  2. The self-diffusion of water and saturated aliphatic alcohols in cation-exchange membranes

    NASA Astrophysics Data System (ADS)

    Volkov, V. I.; Kotov, V. V.; Netesova, G. A.

    2008-07-01

    The self-diffusion of water, methanol, ethanol, isopropanol, and butanol in membranes based on polyethylene and sulfonated copolymer of styrene and divinylbenzene (MK-100) and membranes based on sulfo-containing aromatic polyamides (PA) and a copolymer of 1,2,4,5-benzenetetracarboxylic acid with 4,4'-diaminodiphenyl oxide (PAK) was investigated by the pulsed magnetic field gradient NMR technique. In MK-100 sulfo cation-exchange membranes and PAK carboxylic membranes, two types of sorbate molecules with translational mobilities differing by an order of magnitude were observed. It was established that, in these membranes, the major diffusant portion was transferred trough transport channels formed by functional groups of membranes, counterions, and diffusant molecules (ionogenic channels). The conclusion was drawn that, in PA membranes, water and alcohol molecules were distributed uniformly and carbonyl croups of the polymeric matrix participated in the formation of transport channels. Relations between the structure of membranes, the character of diffusant-polymeric matrix interaction, and the translational mobility of sorbate molecules were found.

  3. Solvent modulation strategy for superior antibody monomer/aggregate separation in cation exchange chromatography.

    PubMed

    Kluters, Simon; Frech, Christian; von Hirschheydt, Thomas; Schaubmar, Andreas; Neumann, Sebastian

    2015-12-01

    Cation exchange chromatography (CEX) is an integral part of many downstream processes for monoclonal antibodies (mAbs). However, in some cases CEX methods with standard mobile phase conditions do not lead to a sufficient removal of soluble antibody aggregates. The addition of neutral polymers such as polyethylene glycol (PEG) to the mobile phase can improve the separation of proteins in IEC remarkably. The applicability of this solvent modulation technique is limited by protein precipitation at higher PEG concentrations. To overcome this limitation solubility enhancers like polyols and amino acids can be added to the mobile phase. These additives are known to inhibit PEG-induced protein precipitation in solution. This new solvent modulation strategy was tested with three different mAbs on two different CEX resins in the presence of PEG in combination with various solubility enhancers. In order to assess the general applicability of this method, mAbs were selected that show major differences with respect to their sensitivity to PEG-induced precipitation and monomer/aggregate resolution performance that is achieved by CEX under standard conditions. For all three mAbs precipitation could be prevented without elimination of the positive PEG-effect. The addition of solubility enhancers gives access to improved separation at elevated PEG concentrations and high protein loadings without running into precipitation issues. Our data indicate that this method is generically applicable and leads to a superior antibody monomer/aggregate separation. PMID:26520020

  4. Sorption of (226)Ra from oil effluents onto synthetic cation exchangers.

    PubMed

    Al Attar, Lina; Safia, Bassam

    2013-07-30

    Increasing environmental awareness is being urged for the safe disposal of (226)Ra-contaminated production water generated in the oil industry. Birnessite, antimony silicate and their cationic derivatives were studied for the take-up of (226)Ra using the batch-type method under experimentally determined parameters, viz. contact time, solution-solid ratio and (226)Ra concentration. Data was expressed in terms of distribution coefficients. Sorption experiments were performed in different concentrations of nitric acid in order to speculate the mechanism of (226)Ra uptake. Variation in the magnitude of sorption efficiency of the materials in the presence of the major components of waste streams, i.e. Na(+), K(+) and Ca(2+), revealed that K(+) was the greatest competitor and Na(+) the least. The application of the materials to sorb (226)Ra from actual oil co-production water samples, collected from Der Ezzor and Al Fourat petroleum companies (DEZPC and AFPC), was interpreted in terms of the exchange properties of the materials and water characterisation. Of the parameters studied, the selectivity of materials was shown to be greatly dependent on the pH of wastewater to be treated. PMID:23623032

  5. Rapid analysis for theophylline in serum by use of high-pressure cation-exchange chromatography.

    PubMed

    Weinberger, M; Chidsey, C

    1975-06-01

    We have developed a quantitative assay for serum theophylline by high-pressure cation-exchange chromatography. As little as 0.1-ml aliquots of serum were prepared for analysis simply by diluting them with a solution of the internal standard (8-chlorotheophylline). Theophylline and the internal standard were eluted in 17 and 27.5 min, respectively, and the peaks for them were distinct from those of other xanthines and uric acids. We encountered no interference when we used: (a) plasma obtained from blood anticoagulated with citrate; (b) hemolyzed, lipemic, or icteric serum; or (c) 52 samples from patients who were receiving various other medications. An analysis of calibration suggested that errors greater than plus or minus 2.6 mg/liter, a clinically acceptable range, were highly unlikely. Sensitivity was sufficient to identify less than 2.5 mg/liter. This assay was compared with the usual method involving solvent extraction and absorbance measurement in the ultraviolet and found to have similar accuracy, although it is easier, faster, requires less sample, and potentially is more specific.

  6. Cation exchange in a temporally fluctuating thin freshwater lens on top of saline groundwater

    NASA Astrophysics Data System (ADS)

    Eeman, S.; De Louw, P. G. B.; Van der Zee, S. E. A. T. M.

    2016-10-01

    In coastal-zone fields with a high groundwater level and sufficient rainfall, freshwater lenses are formed on top of saline or brackish groundwater. The fresh and the saline water meet at shallow depth, where a transition zone is found. This study investigates the mixing zone that is characterized by this salinity change, as well as by cation exchange processes, and which is forced by seepage and by rainfall which varies as a function of time. The processes are first investigated for a one-dimensional (1D) stream tube perpendicular to the interface concerning salt and major cation composition changes. The complex sequence of changes is explained with basic cation exchange theory. It is also possible to show that the sequence of changes is maintained when a two-dimensional field is considered where the upward saline seepage flows to drains. This illustrates that for cation exchange, the horizontal component (dominant for flow of water) has a small impact on the chemical changes in the vertical direction. The flow's horizontal orientation, parallel to the interface, leads to changes in concentration that are insignificant compared with those that are found perpendicular to the interface, and are accounted for in the 1D flow tube. Near the drains, differences with the 1D considerations are visible, especially in the longer term, exceeding 100 years. The simulations are compared with field data from the Netherlands which reveal similar patterns.

  7. A rice tonoplastic calcium exchanger, OsCCX2 mediates Ca2+/cation transport in yeast

    PubMed Central

    Yadav, Akhilesh K.; Shankar, Alka; Jha, Saroj K.; Kanwar, Poonam; Pandey, Amita; Pandey, Girdhar K.

    2015-01-01

    In plant cell, cations gradient in cellular compartments is maintained by synergistic action of various exchangers, pumps and channels. The Arabidopsis exchanger family members (AtCCX3 and AtCCX5) were previously studied and belong to CaCA (calcium cation exchangers) superfamily while none of the rice CCXs has been functionally characterized for their cation transport activities till date. Rice genome encode four CCXs and only OsCCX2 transcript showed differential expression under abiotic stresses and Ca2+ starvation conditions. The OsCCX2 localized to tonoplast and suppresses the Ca2+ sensitivity of K667 (low affinity Ca2+ uptake deficient) yeast mutant under excess CaCl2 conditions. In contrast to AtCCXs, OsCCX2 expressing K667 yeast cells show tolerance towards excess Na+, Li+, Fe2+, Zn2+ and Co2+ and suggest its ability to transport both mono as well as divalent cations in yeast. Additionally, in contrast to previously characterized AtCCXs, OsCCX2 is unable to complement yeast trk1trk2 double mutant suggesting inability to transport K+ in yeast system. These finding suggest that OsCCX2 having distinct metal transport properties than previously characterized plant CCXs. OsCCX2 can be used as potential candidate for enhancing the abiotic stress tolerance in plants as well as for phytoremediation of heavy metal polluted soil. PMID:26607171

  8. A rice tonoplastic calcium exchanger, OsCCX2 mediates Ca2+/cation transport in yeast.

    PubMed

    Yadav, Akhilesh K; Shankar, Alka; Jha, Saroj K; Kanwar, Poonam; Pandey, Amita; Pandey, Girdhar K

    2015-11-26

    In plant cell, cations gradient in cellular compartments is maintained by synergistic action of various exchangers, pumps and channels. The Arabidopsis exchanger family members (AtCCX3 and AtCCX5) were previously studied and belong to CaCA (calcium cation exchangers) superfamily while none of the rice CCXs has been functionally characterized for their cation transport activities till date. Rice genome encode four CCXs and only OsCCX2 transcript showed differential expression under abiotic stresses and Ca(2+) starvation conditions. The OsCCX2 localized to tonoplast and suppresses the Ca(2+) sensitivity of K667 (low affinity Ca(2+) uptake deficient) yeast mutant under excess CaCl2 conditions. In contrast to AtCCXs, OsCCX2 expressing K667 yeast cells show tolerance towards excess Na(+), Li(+), Fe(2+), Zn(2+) and Co(2+) and suggest its ability to transport both mono as well as divalent cations in yeast. Additionally, in contrast to previously characterized AtCCXs, OsCCX2 is unable to complement yeast trk1trk2 double mutant suggesting inability to transport K(+) in yeast system. These finding suggest that OsCCX2 having distinct metal transport properties than previously characterized plant CCXs. OsCCX2 can be used as potential candidate for enhancing the abiotic stress tolerance in plants as well as for phytoremediation of heavy metal polluted soil.

  9. Alkali recovery using PVA/SiO2 cation exchange membranes with different -COOH contents.

    PubMed

    Hao, Jianwen; Gong, Ming; Wu, Yonghui; Wu, Cuiming; Luo, Jingyi; Xu, Tongwen

    2013-01-15

    By changing -COOH content in poly(acrylic acid-co-methacryloxypropyl trimethoxy silane (poly(AA-co-γ-MPS)), a series of PVA/SiO(2) cation exchange membranes are prepared from sol-gel process of poly(AA-co-γ-MPS) in presence of poly(vinyl alcohol) (PVA). The membranes have the initial decomposition temperature (IDT) values of 236-274 °C. The tensile strength (TS) ranges from 17.4 MPa to 44.4 MPa. The dimensional stability in length (DS-length) is in the range of 10%-25%, and the DS-area is in the range of 21%-56% in 65 °C water. The water content (W(R)) ranges from 61.2% to 81.7%, the ion exchange capacity (IEC) ranges from 1.69 mmol/g to 1.90 mmol/g. Effects of -COOH content on diffusion dialysis (DD) performance also are investigated for their potential applications. The membranes are tested for recovering NaOH from the mixture of NaOH/Na(2)WO(4) at 25 - 45 °C. The dialysis coefficients of NaOH (U(OH)) are in the range of 0.006-0.032 m/h, which are higher than those of the previous membranes (U(OH): 0.0015 m/h, at 25 °C). The selectivity (S) can reach up to 36.2. The DD performances have been correlated with the membrane structure, especially the continuous arrangement of -COOH in poly(AA-co-γ-MPS) chain.

  10. Effect of quinidine on cation exchange in cultured cells.

    PubMed

    McCall, D

    1976-06-01

    The effects of quinidine on membrane ion exchange were examined using monolayer cultures of mammalian cells. Quinidine, in concentrations from 10(-6) to 10(-3) M, produced a prompt inhibition of the passive Na influx, dose-dependent along a sigmoid log dose-response curve. This effect was at a maximum for each concentration of the drug within 30 seconds of application. Passive Na influx (pmol/cm2/sec) decreased from 18.8 to 17.6 (P less than .05) and 10.5 (P less than .001) in the presence of 10(-6) and 10(-3) M quinidine, respectively. In the continued presence of quinidine, there was no further time-dependent effect on the Na influx, nor was there any tendency for the influx to recover. Washing the cells free of quinidine, however, resulted in a return of Na influx to control levels within 1 to 3 minutes. After 1 to 2 minute of quinidine treatment, coupled active Na efflux/K influx rapidly declined, reaching minimum values for each concentration between 2 to 4 minutes of drug treatment. Beyond that time, active Na/K fluxes again increased, but to values which remained significantly less than control, for up to 4 hours. Ten minutes of exposure to quinidine were required before any demonstrable effect on the passive K efflux could be recorded. In the presence of quinidine, there was reduced membrane turnover of both Na and K, but such that after a brief initial period (10 minutes or less) both ions were in flux equilibrium, explaining the absence of change in [Nai] and [Ki] in the presence of quinidine. Calculations of Ec1 indicated that, when present for 4 hours, quinidine did not change the Em in these cells although significant (P less than .001) reductions in apparent PNa and Pk values were recorded. The effect on PNa was much greater than that on Pk. The quinidine-induced flux changes occurred in a definite temporal sequence suggesting that they could all be explained on the basis of one direct initial action. This initial direct action, namely the prompt

  11. Mathematical Modeling of Cation Contamination in a Proton-exchange Membrane

    SciTech Connect

    Weber, Adam; Delacourt, Charles

    2008-09-11

    Transport phenomena in an ion-exchange membrane containing both H+ and K+ are described using multicomponent diffusion equations (Stefan-Maxwell). A model is developed for transport through a Nafion 112 membrane in a hydrogen-pump setup. The model results are analyzed to quantify the impact of cation contamination on cell potential. It is shown that limiting current densities can result due to a decrease in proton concentration caused by the build-up of contaminant ions. An average cation concentration of 30 to 40 percent is required for appreciable effects to be noticed under typical steady-state operating conditions.

  12. Recovery of boric acid from ion exchangers

    DOEpatents

    Pollock, Charles W.

    1976-01-01

    The recovery of boric acid from an anion exchange resin is improved by eluting the boric acid with an aqueous solution of ammonium bicarbonate. The boric acid can be readily purified and concentrated by distilling off the water and ammonium bicarbonate. This process is especially useful for the recovery of boric acid containing a high percentage of .sup.10 B which may be found in some nuclear reactor coolant solutions.

  13. Composite membranes prepared from cation exchange membranes and polyaniline and their transport properties in electrodialysis

    SciTech Connect

    Sata, Tshikatsu; Ishii, Yuuko; Kawamura, Kohei; Matsusaki, Koji

    1999-02-01

    A cation exchange membrane was modified with polyaniline by polymerizing aniline with ammonium peroxodisulfate on the membrane surfaces, producing a membrane with polyaniline layers on both surfaces or a membrane with a single polyaniline layer on the surface. The modified membranes, composite membranes, showed sodium ion permselectivity in electrodialysis compared with divalent cations at an optimum polymerization time. The electronic conductivity of dry membranes showed a maximum (ca. 5 {times} 10{sup {minus}3} S/cm) at the same polymerization time as the time to attain a maximum value of the sodium ion permselectivity. Because emeraldine-based polyaniline is conductive and has a cationic charge, the sodium ion permselectivity is based on the difference in the electrostatic repulsion forces of the cationic charge on the membrane surface of a desalting side to divalent cations and sodium ions. In fact, the selective permeation of sodium ions appeared only when the layer faced the desalting side of the membrane, and was affected by dissociation of polyaniline. Further oxidized polyaniline, pernigraniline-based polyaniline, did not affect the permselectivity between cations, and the diffusion coefficient of neutral molecules, urea, increased with increasing polymerization time. Sodium ion permselectivity was maintained with repeated electrodialysis.

  14. In-situ graft-polymerization preparation of cation-exchange supermacroporous cryogel with sulfo groups in glass columns.

    PubMed

    Yao, Kejian; Yun, Junxian; Shen, Shaochuan; Chen, Fang

    2007-07-20

    Graft polymerization of monomer chains with expected functional groups onto the matrix pore surfaces by initiator is an effective approach for introducing ion-exchange groups to cryogel matrix to get anion- or cation-exchange supermacroporous cryogels. In this work, a novel cation-exchange cryogel with sulfo binding groups was prepared by grafting of 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPSA) onto polyacrylamide-based cryogels in glass columns. The grafting polymerization was achieved in an in-situ manner which was performed by pumping the initiator and the reactive solution of graft monomer with sulfo binding groups directly through a cryogel bed pre-produced in a glass column under frozen condition. The axial liquid dispersion characteristics within the monolithic cryogel beds before and after the in-situ polymerization were compared by measuring residence time distributions (RTDs) at various liquid flow rates using tracer pulse-response method. Microstructure morphology of pores within cryogels was analyzed by scanning electron microscopy (SEM). Chromatography of lysozyme was carried out to reveal the protein breakthrough and elution characteristics in the obtained cryogel beds.

  15. In-situ graft-polymerization preparation of cation-exchange supermacroporous cryogel with sulfo groups in glass columns.

    PubMed

    Yao, Kejian; Yun, Junxian; Shen, Shaochuan; Chen, Fang

    2007-07-20

    Graft polymerization of monomer chains with expected functional groups onto the matrix pore surfaces by initiator is an effective approach for introducing ion-exchange groups to cryogel matrix to get anion- or cation-exchange supermacroporous cryogels. In this work, a novel cation-exchange cryogel with sulfo binding groups was prepared by grafting of 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPSA) onto polyacrylamide-based cryogels in glass columns. The grafting polymerization was achieved in an in-situ manner which was performed by pumping the initiator and the reactive solution of graft monomer with sulfo binding groups directly through a cryogel bed pre-produced in a glass column under frozen condition. The axial liquid dispersion characteristics within the monolithic cryogel beds before and after the in-situ polymerization were compared by measuring residence time distributions (RTDs) at various liquid flow rates using tracer pulse-response method. Microstructure morphology of pores within cryogels was analyzed by scanning electron microscopy (SEM). Chromatography of lysozyme was carried out to reveal the protein breakthrough and elution characteristics in the obtained cryogel beds. PMID:17517417

  16. Acidic deposition, cation mobilization, and biochemical indicators of stress in healthy red spruce

    SciTech Connect

    Shortle, W.C.; Smith, K.T.; Minocha, R.

    1997-05-01

    Dendrochemical and biochemical markers link stress in apparently healthy red spruce trees (Picea rubens) to acidic deposition. Previous reports related visible damage of trees at high elevations to root and soil processes. In this report, dendrochemical and foliar biochemical markers indicate perturbations in biological processes in healthy red spruce trees across the northeastern USA. Previous research on the dendrochemistry of red spruce stemwood indicated that under uniform environmental conditions, stemwood concentrations of Ca and Mg decreased with increasing radial distance from the pith. For nine forest locations, frequency analysis shows that 28 and 52% of samples of red spruce stemwood formed in the 1960s are enriched in Ca and Mg, respectively, relative to wood formed prior to and after the 1960s. This enrichment in trees throughout the northeastern USA may be interpretable as a signal of increased availability of essential cations in forest soils. Such a temporary increase in the availability of Ca and Mg could be caused by cation mobilization, a consequence of increased acidic deposition. During cation mobilization, essential and Ca and Mg as well as potentially harmful Al become more available for interaction with binding sites in the soil and absorbing roots. As conditions which favor cation mobilization continue, Ca and Mg can be leached or displaced from the soil. A measure of the interaction between Ca and Al is the Al/Ca binding ratio (molar charge ratio of exchangeable Al to exchangeable Ca). As the Al/Ca binding ratio in the root zone increased from 0.3 to 1.9, the foliar concentration of the biochemical stress marker putrescine also increased form 45 to 145 nm g{sup {minus}1}. The correlation of the putrescine concentration to the Al/Ca binding ratio (adj. r{sup 2} = 0.68, P <0.027) suggests that foliar stress may be linked to soil chemistry. 32 refs., 2 figs., 1 tab.

  17. The group separation of the rare-earth elements and yttrium from geologic materials by cation-exchange chromatography

    USGS Publications Warehouse

    Crock, J.G.; Lichte, F.E.; Wildeman, T.R.

    1984-01-01

    Demand is increasing for the determination of the rare-earth elements (REE) and yttrium in geologic materials. Due to their low natural abundance in many materials and the interferences that occur in many methods of determination, a separation procedure utilizing gradient strong-acid cation-exchange chromatography is often used to preconcentrate and isolate these elements from the host-rock matrix. Two separate gradient strong-acid cation-exchange procedures were characterized and the major elements as well as those elements thought to provide the greatest interference for the determination of the REE in geologic materials were tested for separation from the REE. Simultaneous inductively coupled argon plasma-atomic emission spectroscopy (ICAP-AES) measurements were used to construct the chromatograms for the elution studies, allowing the elution patterns of all the elements of interest to be determined in a single fraction of eluent. As a rock matrix, U.S. Geological Survey standard reference BCR-1 basalt was digested using both an acid decomposition procedure and a lithium metaborate fusion. Hydrochloric and nitric acids were tested as eluents and chromatograms were plotted using the ICAP-AES data; and we observed substantial differences in the elution patterns of the REE and as well as in the solution patterns of Ba, Ca, Fe and Sr. The nitric acid elution required substantially less eluent to elute the REE and Y as a group when compared to the hydrochloric acid elution, and provided a clearer separation of the REE from interfering and matrix elements. ?? 1984.

  18. Effect of sodium and calcium cations on the ion-exchange affinity of organic cations for soil organic matter.

    PubMed

    Droge, Steven; Goss, Kai-Uwe

    2012-06-01

    Sorption of organic cations to soil organic matter was studied using dynamic column experiments with different compositions of electrolytes in aqueous eluents. The sorption affinity of the tested variety of charged compounds, including primary, secondary, and tertiary amines and quaternary ammonium compounds, all showed the same response to different medium compositions. The sorption affinity to Pahokee peat (i) strongly decreased with increasing electrolyte concentration, up to a factor 250 due to tested electrolyte compositions alone, (ii) was higher in NaCl solutions than in CaCl(2) solutions of similar ionic strength, and (iii) was more sensitive to a decrease in NaCl than to a decrease in CaCl(2), though the selectivity coefficients were not significantly different. For a weak base that was tested in eluent pH either above or below its pK(a), we demonstrated that the sorption affinity of (iv) the neutral base was hardly affected by different electrolyte compositions, comparable to a neutral reference compound, (v) the protonated weak base was strongly affected by different electrolyte compositions, and (vi) the protonated base was in the same range, or stronger, compared to the neutral base. Mass action law equations for ion-exchange reactions predicted similar trends in a qualitative but not in a quantitative way. More complex models are required to fully account for the contributions of ionic interactions to the sorption of organic cations. These results imply that risk assessment models for organic bases should take ion-exchange processes into account when estimating soil sorption coefficients and bioavailability. PMID:22540998

  19. Full cell study of Diels Alder poly(phenylene) anion and cation exchange membranes in vanadium redox flow batteries

    DOE PAGES

    Pezeshki, Alan M.; Fujimoto, Cy; Sun, Che -Nan; Mench, Matthew M.; Zawodzinski, Thomas A.; Tang, Z. J.

    2015-11-14

    In this paper, we report on the performance of Diels Alder poly(phenylene) membranes in vanadium redox flow batteries. The membranes were functionalized with quaternary ammonium groups to form an anion exchange membrane (QDAPP) and with sulfonic acid groups to form a cation exchange membrane (SDAPP). Both membrane classes showed similar conductivities in the battery environment, suggesting that the ion conduction mechanism in the material is not strongly affected by the moieties along the polymer backbone. The resistance to vanadium permeation in QDAPP was not improved relative to SDAPP, further suggesting that the polarity of the functional groups do not playmore » a significant role in the membrane materials tested. Both QDAPP and SDAPP outperformed Nafion membranes in cycling tests, with both achieving voltage efficiencies above 85% while maintaining 95% coulombic efficiency while at a current density of 200 mA/cm2.« less

  20. Full cell study of Diels Alder poly(phenylene) anion and cation exchange membranes in vanadium redox flow batteries

    SciTech Connect

    Pezeshki, Alan M.; Fujimoto, Cy; Sun, Che -Nan; Mench, Matthew M.; Zawodzinski, Thomas A.; Tang, Z. J.

    2015-11-14

    In this paper, we report on the performance of Diels Alder poly(phenylene) membranes in vanadium redox flow batteries. The membranes were functionalized with quaternary ammonium groups to form an anion exchange membrane (QDAPP) and with sulfonic acid groups to form a cation exchange membrane (SDAPP). Both membrane classes showed similar conductivities in the battery environment, suggesting that the ion conduction mechanism in the material is not strongly affected by the moieties along the polymer backbone. The resistance to vanadium permeation in QDAPP was not improved relative to SDAPP, further suggesting that the polarity of the functional groups do not play a significant role in the membrane materials tested. Both QDAPP and SDAPP outperformed Nafion membranes in cycling tests, with both achieving voltage efficiencies above 85% while maintaining 95% coulombic efficiency while at a current density of 200 mA/cm2.

  1. Association between cationic liposomes and low molecular weight hyaluronic acid.

    PubMed

    Gasperini, Antonio A M; Puentes-Martinez, Ximena E; Balbino, Tiago Albertini; Rigoletto, Thais de Paula; Corrêa, Gabriela de Sá Cavalcanti; Cassago, Alexandre; Portugal, Rodrigo Villares; de La Torre, Lucimara Gaziola; Cavalcanti, Leide P

    2015-03-24

    This work presents a study of the association between low molecular weight hyaluronic acid (16 kDa HA) and cationic liposomes composed of egg phosphatidylcholine (EPC), 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine (DOPE), and 1,2-dioleoyl-3-trimethylammonium-propane (DOTAP). The cationic liposome/HA complexes were evaluated to determine their mesoscopic structure, average size, zeta potential, and morphology as a function of the amount of HA in the system. Small angle X-ray scattering results revealed that neighboring cationic liposomes either stick together after a partial coating of low concentration HA or disperse completely in excess of HA, but they never assemble as multilamellar vesicles. Cryo-transmission electron microscopy images confirm the existence of unilamellar vesicles and large aggregates of unilamellar vesicles for HA fractions up to 80% (w/w). High concentrations of HA (> 20% w/w) proved to be efficient for coating extruded liposomes, leading to particle complexes with sizes in the nanoscale range and a negative zeta potential.

  2. Time-Resolved Structural Analysis of Cation Exchange Reactions in Birnessite Using Synchrotron XRD

    NASA Astrophysics Data System (ADS)

    Lopano, C. L.; Heaney, P. J.; Post, J. E.; Hanson, J. C.; Lee, Y.; Komarneni, S.

    2002-12-01

    Birnessite ((Na,Ca,Mn2+) Mn7O142.8H2O) is a layered Mn-oxide with a 7.2Å spacing between the Mn octahedral sheets. Since birnessite is an abundant phase in soils, desert varnishes, and ocean nodules, it plays a significant role in soil and groundwater chemistry. Experiments by Golden et al. (1986,1987) have demonstrated that Na-buserite (hydrated birnessite) readily exchanges Na+ for a variety of other cations, including K+, Mg2+, Ca2+, Ba2+, Ni2+, and Sr2+. In light of its high cation exchange capacity, birnessite is industrially important for ion and molecular sieves and cathodic materials. In addition, birnessite serves as a precursor in the synthesis of todorokite, which has a 3x3 tunnel structure and is used as an octahedral sieve. We monitored cation-exchange reactions in birnessite by time-resolved X-ray powder diffraction with a simple flow-through cell at the National Synchrotron Light Source. The flow-through cell was developed by Lee and Parise at SUNY-Stony Brook, and this work represents its first application to Mn oxides. A series of synthetic Na-birnessite samples were saturated with chloride solutions containing dissolved K+, Mg2+, and Ba2+, ranging from 0.1M to 0.001M. Powder X-ray diffraction patterns were collected every ~ 3 minutes. The synchrotron experiments revealed that complete cation exchange occurs within three hours, and significant modifications of the arrangements of interlayer cations and water molecules accompany the exchange. Specifically, the replacement of Na by Mg resulted in the continuous growth of a discrete buserite-like phase with a 10Å layer spacing, while replacement of Na by K and Ba retained the 7Å spacing. K replacement of Na resulted in gradually decreasing peak intensity and peak merging. The Ba exchange yielded an abrupt decrease in diffraction intensities followed by a more gradual lattice change over the last 2 hours. Rietveld analysis led to the first determination of the structure of Ba-birnessite in space

  3. Dehydration enthalpy of alkali-cations-exchanged montmorillonite from thermogravimetric analysis.

    PubMed

    Kharroubi, M; Balme, S; Henn, F; Giuntini, J C; Belarbi, H; Haouzi, A

    2009-01-15

    Dehydration of a series of homoionic alkali-exchanged montmorillonites is studied at different treatment temperatures by means of thermogravimetric analysis. More specifically, we investigate the last stages of dehydration when the number of adsorbed water molecules corresponds, at maximum, to a monolayer. Weight losses are measured at several constant temperatures as a function of time. Application of Van't Hoff's law yields the dehydration enthalpy. Trends and data similar to those reported from other experimental conditions are found. Comparison with X-ray data and with the dissociation enthalpy of alkali cation/water complexes shows that dehydration of weakly hydrated homoionic alkali montmorillonites results from the competition between opposite energy contributions due to (i) the cation solvation, (ii) the hydration of the silicate interlayer surface, and (iii) the structural swelling. So, depending on the balance between these various energy contributions, different behaviors are observed according to the nature of the alkali cations. PMID:18973904

  4. Transition metal cation separations with a resorcinarene-based amino acid stationary phase.

    PubMed

    Li, Na; Allen, Lee J; Harrison, Roger G; Lamb, John D

    2013-03-01

    A resorcinarene-based macrocyclic ligand functionalized with alanine and undecyl groups (AUA) was synthesized and applied to ion chromatographic separations. The selectivity and separation of transition metal ions on a column packed with AUA adsorbed onto 55% cross-linked styrene-divinylbenzene resin are presented. The upper and lower rims of the resorcinarene were modified with amino acids and -C(11)H(23) alkyl chains, respectively. The four carboxylic acid groups on the upper rim act as cation-exchangers while the four -C(11)H(23) alkyl chains serve to anchor the ligand to the resin surface by the hydrophobic effect. A systematic study of the effect of different eluent components including non-metal-chelating (HNO(3)) and chelating acids (oxalic acid, succinic acid, dipicolinic acid, and citric acid) on the retention of transition metal ions was investigated. Six metal ions (Mn(2+), Co(2+), Ni(2+), Cd(2+), Cu(2+), and Zn(2+)) were separated on the AUA column within a reasonable time with a single eluent gradient using oxalic acid. The separation is compared to that obtained using a commercial column containing carboxylic acid functional groups. The AUA column containing four preorganized carboxylic acid groups showed selectivity for Cu(2+) when no chelating eluent was present, a selectivity which was not observed with the comparison column.

  5. Effects of acid precipitation on cation transport in New Hampshire forest soils. Technical completion report

    SciTech Connect

    Cronan, C.S.

    1981-07-01

    This report describes the results of our investigation of the effects of regional acid precipitation on forest soils and watershed biogeochemistry in New England. The report provides descriptions of the following research findings: (1) acid precipitation may cause increased aluminum mobilization and leaching from soils to sensitive aquatic systems; (2) acid deposition may shift the historic carbonic acid/organic acid leaching regime in forest soils to one dominated by atmospheric H/sub 2/SO/sub 4/; (3) acid precipitation may accelerate nutrient cation leaching from forest soils and may pose a particular threat to the potassium resources of northeastern forested ecosystems; (4) while acid rain may pass through some coniferous canopies without being neutralized, similar inputs of acid rainfall to hardwood canopies may be neutralized significantly by Bronsted base leaching and by leaf surface ion exchange mechanisms; and (5) progressive acid dissolution of soils in the laboratory may provide an important tool for predicting the patterns of aluminum leaching from soils exposed to acid deposition.

  6. Chemistry of alkali cation exchanged faujasite and mesoporous NaX using alkyl halides and phosphates

    NASA Astrophysics Data System (ADS)

    Lee, Min-Hong

    The purpose of this work was to increase the reactivity of Faujasite X (NaX) zeolite toward the reactive decontamination of materials subject to nucleophilic attack by means of zeolite cation optimization and by means of the synthesis of mesoporous Faujasite X. Primary alkyl halides and trialkyl phosphates have been the test materials on which the cation-optimized and mesoporous zeolites have been tested. In the alkali cation optimization work, reactions of methyl iodide and 1-chloropropane with alkali metal cation exchanged Faujasite zeolite X were investigated at room temperature. The reactivity of the framework and the product formation were shown to depend on zeolite framework counter-cation. A quantitative study of zeolite product formation has been carried out, primarily using solid-state NMR spectroscopy. Large alkali cations showed preference toward substitution chemistry. In contrast, alkyl halide exposed LiX and NaX zeolites underwent both substitution and elimination. Subsequently introduced water molecules led to hydrolysis of framework species that was sensitive to framework counter-cation. The mesoporous NaX zeolites work undertakes to test whether an improvement in surface chemical reactivity can be achieved by introducing mesopores into the already reactive nucleophilic microporous NaX zeolite. Incorporation of the polydiallyl dimethyl ammonium chloride (PDADMAC) template and the formation of mesopores in Faujasite X zeolite (NaX) were successful and well-characterized. The mesopores are proposed to have occurred from incorporation of the cationic PDADMAC polymer into the zeolite by compensating zeolite framework charge. Subsequent sodium cation exchange of calcined mesoporous NaX was shown to restore the chemical reactivity characteristic of as-synthesized NaX. Trialkyl organophosphorous compounds underwent substitution reactions. The reactivity of both microporous and mesoporous Faujasite zeolite X and the product formation was shown to depend on

  7. Multicolour synthesis in lanthanide-doped nanocrystals through cation exchange in water

    PubMed Central

    Han, Sanyang; Qin, Xian; An, Zhongfu; Zhu, Yihan; Liang, Liangliang; Han, Yu; Huang, Wei; Liu, Xiaogang

    2016-01-01

    Meeting the high demand for lanthanide-doped luminescent nanocrystals across a broad range of fields hinges upon the development of a robust synthetic protocol that provides rapid, just-in-time nanocrystal preparation. However, to date, almost all lanthanide-doped luminescent nanomaterials have relied on direct synthesis requiring stringent controls over crystal nucleation and growth at elevated temperatures. Here we demonstrate the use of a cation exchange strategy for expeditiously accessing large classes of such nanocrystals. By combining the process of cation exchange with energy migration, the luminescence properties of the nanocrystals can be easily tuned while preserving the size, morphology and crystal phase of the initial nanocrystal template. This post-synthesis strategy enables us to achieve upconversion luminescence in Ce3+ and Mn2+-activated hexagonal-phased nanocrystals, opening a gateway towards applications ranging from chemical sensing to anti-counterfeiting. PMID:27698348

  8. Multicolour synthesis in lanthanide-doped nanocrystals through cation exchange in water

    NASA Astrophysics Data System (ADS)

    Han, Sanyang; Qin, Xian; An, Zhongfu; Zhu, Yihan; Liang, Liangliang; Han, Yu; Huang, Wei; Liu, Xiaogang

    2016-10-01

    Meeting the high demand for lanthanide-doped luminescent nanocrystals across a broad range of fields hinges upon the development of a robust synthetic protocol that provides rapid, just-in-time nanocrystal preparation. However, to date, almost all lanthanide-doped luminescent nanomaterials have relied on direct synthesis requiring stringent controls over crystal nucleation and growth at elevated temperatures. Here we demonstrate the use of a cation exchange strategy for expeditiously accessing large classes of such nanocrystals. By combining the process of cation exchange with energy migration, the luminescence properties of the nanocrystals can be easily tuned while preserving the size, morphology and crystal phase of the initial nanocrystal template. This post-synthesis strategy enables us to achieve upconversion luminescence in Ce3+ and Mn2+-activated hexagonal-phased nanocrystals, opening a gateway towards applications ranging from chemical sensing to anti-counterfeiting.

  9. Bifunctional phenyl monophosphonic/sulfonic acid ion exchange resin and process for using the same

    DOEpatents

    Alexandratos, Spiro; Shelley, Christopher A.; Horwitz, E. Philip; Chiarizia, Renato

    2001-01-01

    A cross-linked water-insoluble ion exchange resin comprised of polymerized monomers having a phenyl ring is disclosed. A contemplated resin contains (i) polymerized phenyl ring-containing monomers having a phosphonic acid ligand linked to the phenyl ring, (ii) about 2 to about 5 millimoles per gram (mmol/g) of phosphorus as phosphonic acid ligands, and (iii) a sufficient amount of a sulfonic acid ligand such that the ratio of mmol/g of phosphonic acid to mmol/g sulfonic acid is up to 3:1. A process for removing polyvalent metal cations from aqueous solution, and a process for removing iron(III) cations from acidic copper(II) cation-containing solutions that utilize the contemplated resin or other resins are disclosed.

  10. Bifunctional phenyl monophosphonic/sulfonic acid ion exchange resin and process for using the same

    DOEpatents

    Alexandratos, Spiro; Shelley, Christopher A.; Horwitz, E. Philip; Chiarizia, Renato; Gula, Michael J.; Xue, Sui; Harvey, James T.

    2002-01-01

    A cross-linked water-insoluble ion exchange resin comprised of polymerized monomers having a phenyl ring is disclosed. A contemplated resin contains (i) polymerized phenyl ring-containing monomers having a phosphonic acid ligand linked to the phenyl ring, (ii) about 2 to about 5 millimoles per gram (mmol/g) of phosphorus as phosphonic acid ligands, and (iii) a sufficient amount of a sulfonic acid ligand such that the ratio of mmol/g of phosphonic acid to mmol/g sulfonic acid is up to 3:1. A process for removing polyvalent metal cations from aqueous solution, and a process for removing iron(III) cations from acidic copper(II) cation-containing solutions that utilize the contemplated resin or other resins are disclosed.

  11. Use of Cation Exchange Chromatography for Human C-peptide Isotope Dilution – Mass Spectrometric Assay

    PubMed Central

    Stoyanov, Alexander V.; Rohlfing, Curt L.; Connolly, Shawn; Roberts, Matthew L.; Nauser, Christopher L.; Little, Randie R.

    2016-01-01

    An application of ion exchange chromatography for C-peptide analysis is described here. At the stage of C-peptide isolation, a strong cation exchanger (SP HP or MonoS) was used to purify the analyte from ballast proteins and peptides. The conditions of ion-exchange chromatographic separations were optimized using theoretical modeling of the net surface electric charge of the peptide as a function of pH. The purified and concentrated sample was further subjected to LC-MS/MS. In order to improve the reliability of analysis, two fragment ions were monitored simultaneously both for native C-peptide and internal standard, isotopically labeled C-peptides analogues (fragments with m/z of 927.7 and 147.2). Using ion-exchange chromatography, it became possible to process larger sample volumes, important for testing patients with very low C peptide levels, compared to currently used solid phase extraction methods. PMID:22098929

  12. Enhanced photocatalytic activity of chromium(VI) reduction and EDTA oxidization by photoelectrocatalysis combining cationic exchange membrane processes.

    PubMed

    Hsu, Hung-Te; Chen, Shiao-Shing; Tang, Yi-Fang; Hsi, Hsing-Cheng

    2013-03-15

    A novel technology of photoelectrocatalysis (PEC) combining with cationic exchange membrane (CEM) was proposed for simultaneous reduction of chromium(VI) and oxidization of EDTA. The application of CEM was used to enhance the efficiency for prevention of the re-oxidation of reduced chromium with the electron-hole pairs. In this study, effects of current density, pH, TiO2 dosage, hydraulic retention time (HRT), light intensity and EDTA/Cr(VI) molar ratio were all investigated. The results showed that the optimum conversion efficiency occurred at 4mA/cm(2) with the presence of CEM. Higher conversion efficiencies were observed at lower pH due to the electrostatic attractions between positive charged TiOH2(+), and negatively charged Cr(VI) and EDTA. The optimum TiO2 loading of 1g/L was depended mainly on the acidic pH range, especially at higher HRT and irradiation intensity. In addition, higher EDTA/Cr(VI) molar ratio enhanced the reduction efficiency of Cr(VI), indicating EDTA plays the role of hole scavenger in this system. Moreover, incomplete EDTA decomposition contributes to the occurrence of intermediates, including nitrilotriacetic acid, iminodiacetic acid, glycine, oxamic acid, lyoxylic acid, oxalic acid, acetic acid and formic acid, as identified by GC/MS. Consequently, transformation pathway was determined from these analyzed byproducts and molecular orbital package analysis.

  13. Evaluation of the field-scale cation exchange capacity of Hanford sediments

    SciTech Connect

    Steefel, C.I.

    2003-02-01

    Three-dimensional simulations of unsaturated flow, transport, and multi-component, multi-site cation exchange in the vadose zone were used to analyze the migration of a plume resulting from a leak of the SX-115 tank at the Hanford site, USA. The match within about 0.5 meters of the positions of retarded sodium and potassium fronts suggests that the laboratory-derived parameters may be used in field-scale simulations of radionuclide migration at the Hanford site.

  14. Emission spectrographic determination of barium in sea water using a cation exchange concentration procedure

    USGS Publications Warehouse

    Szabo, B. J.; Joensuu, O.

    1967-01-01

    A concentration technique employing Dowex 50W cation exchange resin is described for the determination of barium in sea water. The separated barium is precipitated as fluoride together with calcium and strontium and measured by emission spectrographic analysis. The vertical distribution of barium in sea water has been measured in the Caribbean Sea and the Atlantic Ocean. The barium content varied between 7 and 23 ??g. per liter; in two profiles, the lowest concentrations were at a depth of about 1000 meters.

  15. DNA strand exchange stimulated by spontaneous complex formation with cationic comb-type copolymer.

    PubMed

    Kim, Won Jong; Akaike, Toshihiro; Maruyama, Atsushi

    2002-10-30

    Cationic comb-type copolymers (CCCs) composed of a polycation backbone and water-soluble side chains accelerate by 4-5 orders the DNA strand exchange reaction (SER) between double helical DNA and its homologous single-strand DNA. The accelerating effect is considered due to alleviation of counterion association during transitional intermediate formation in sequential displacement pathway. CCCs stabilize not only matured hybrids but also the nucleation complex to accelerate hybridization. PMID:12392411

  16. Hydrogeochemistry and cation-exchange processes in the coastal aquifer of Mar Del Plata, Argentina

    NASA Astrophysics Data System (ADS)

    Martínez, D. E.; Bocanegra, E. M.

    2002-06-01

    The aquifer of Mar del Plata is unconfined and composed of silt and fine sand. The sand fraction is mainly quartz, potassium feldspars, chalcedony, and gypsum. Volcanic-glass shards (40-60%) dominate the silt fraction, and the clays are of the smectite and illite groups. Calcium carbonate, in caliche form, constitutes about 10-20% of the sediment. Groundwater flow is from west to east, and discharge is in the Atlantic Ocean. Because of overexploitation, the flow direction was reversed in a coastal belt about 3.5 km wide, and this has resulted in seawater intrusion. The groundwater is the CaHCO3 type in the recharge zone, and becomes NaHCO3 type towards the discharge area. Salinization by marine intrusion and seawater/fresh-water mixing produces an increase in the major-ion concentrations of the groundwater. The calcium content of the groundwater is higher and the sodium content is lower than those that would be expected if the mixing is considered as just the addition of seawater and fresh water in determined proportions without reactive processes taking place. Hydrogeochemical modeling was applied to the study of hydrogeochemical processes, mainly cation exchange, using the codes NETPATH and PHREEQM. Calcite and gypsum equilibrium, together with cation exchange, are the main hydrogeochemical processes. Cation-exchange capacity of the solid phase was determined by empirical calculations and experimental methods. The affinity order for the groundwater in contact with the aquifer matrix is Ca>Mg>Na in the regional-flow system, but the order is reversed in the salinization process. Reactive transport modeling using the code PHREEQM is useful for analyzing cation exchange in a marine-intrusion process.

  17. Solubility and cation exchange in phosphate rock and saturated clinoptilolite mixtures

    NASA Technical Reports Server (NTRS)

    Allen, E. R.; Hossner, L. R.; Ming, D. W.; Henninger, D. L.

    1993-01-01

    Mixtures of zeolite and phosphate rock (PR) have the potential to provide slow-release fertilization of plants in synthetic soils by dissolution and ion-exchange reactions. This study was conducted to examine solubility and cation-exchange relationships in mixtures of PR and NH4- and K-saturated clinoptilolite (Cp). Batch-equilibration experiments were designed to investigate the effect of PR source, the proportion of exchangeable K and NH4, and the Cp to PR ratio on solution N, P, K, and Ca concentrations. The dissolution and cation-exchange reactions that occurred after mixing NH4- and K-saturated Cp with PR increased the solubility of the PR and simultaneously released NH4 and K into solution. The more reactive North Carolina (NC) PR rendered higher solution concentrations of NH4 and K when mixed with Cp than did Tennessee (TN) PR. Solution P concentrations for the Cp-NC PR mixture and the Cp-TN PR mixture were similar. Solution concentrations of N, P, K, and Ca and the ratios of these nutrients in solution varied predictably with the type of PR, the Cp/PR ratio, and the proportions of exchangeable K and NH4 on the Cp. Our research indicated that slow-release fertilization using Cp/PR media may provide adequate levels of N, P, and K to support plant growth. Solution Ca concentrations were lower than optimum for plant growth.

  18. Exchangeable cation composition of the smectite-rich plate boundary fault at the Japan Trench

    NASA Astrophysics Data System (ADS)

    Kameda, Jun; Inaoi, Chisaki; Conin, Marianne

    2016-04-01

    To better understand physicochemical processes in smectite-rich fault zones, we examined exchangeable cation composition of samples from the slip zone of the 2011 Tohoku-oki earthquake (Mw9.0) recovered by the Integrated Ocean Drilling Program Expedition 343. Our chemical analyses revealed that the exchangeable Ca2+ and Mg2+ are enriched in the slip zone, while Na+ is depleted. K+ shows a complicated depth profile probably due to K fixation. Based on fluid chemistry data, we estimated apparent selectivity coefficients of exchange reactions in the ternary Ca2+-Mg2+-Na+ system. The results suggest that the Na+ to Mg2+ exchange reaction on smectite might have progressed in the slip zone. One explanation for this feature is local progress of the reaction triggered by coseismic thermogenesis during the earthquake. Considering that the frictional property of smectite gouge is dependent on the exchangeable cation composition, chemical processes as observed in this study are intimately linked to physical aspect of smectite-bearing faults.

  19. Mobilization of Roadside Soil Cation Pools by Exchange with Road Deicers

    NASA Astrophysics Data System (ADS)

    Rossi, R.; Bain, D.

    2014-12-01

    Over the past sixty years, road deicers (i.e., road salt) have been applied to roadways in high latitudes to improve traffic conditions in winter weather. However, the dissolution of road deicers in highway runoff create waters with high total dissolved solids (TDS), specifically high concentrations of sodium, which can mobilize soil metals via soil cation exchange reactions. While several studies have detailed the interactions of high TDS solutions and surface and ground waters, limited attention is paid to the impacts of high TDS solutions on near-road soils. Between 2013 and 2014, soil water samples were collected from a roadside transect of lysimeter nests in Pittsburgh, PA. Soil water samples were analyzed for metal concentrations and resulting data used to examine cation dynamics. Patterns in soil water calcium and magnesium concentrations follow patterns in soil water sodium concentrations. In our samples, the highest major cation concentrations are found at the deepest lysimeters, suggesting major cations are mobilized to, and potentially accumulate in, deeper soil horizons. Concentration peaks in the downslope soil waters lag concentration peaks at the near-road nest by two months, indicating that road salt plumes persist and migrate following the road salting season. Characterizing the interactions of high TDS solutions and roadside soil cation pools clarifies our understanding of metal dynamics in the roadside environment. A deeper understanding of these processes is necessary to effectively restore and manage watersheds as high TDS solutions (i.e., road deicing, hydraulic fracturing, and marginal irrigation water) increasingly influence ecosystem function.

  20. Cation Exchange in Dynamic 3D Porous Magnets: Improvement of the Physical Properties.

    PubMed

    Grancha, Thais; Acosta, Alvaro; Cano, Joan; Ferrando-Soria, Jesús; Seoane, Beatriz; Gascon, Jorge; Pasán, Jorge; Armentano, Donatella; Pardo, Emilio

    2015-11-16

    We report two novel three-dimensional porous coordination polymers (PCPs) of formulas Li4{Mn4[Cu2(Me3mpba)2]3}·68H2O (2) and K4{Mn4[Cu2(Me3mpba)2]3}·69H2O (3) obtained-via alkali cation exchange in a single-crystal to single-crystal process-from the earlier reported anionic manganese(II)-copper(II) PCP of formula Na4{Mn4[Cu2(Me3mpba)2]3}·60H2O (1) [Me3mpba(4-) = N,N'-2,4,6-trimethyl-1,3-phenylenebis(oxamate)]. This postsynthetic process succeeds where the direct synthesis in solution from the corresponding building blocks fails and affords significantly more robust PCPs with enhanced magnetic properties [long-range 3D magnetic ordering temperatures for the dehydrated phases (1'-3') of 2.0 (1'), 12.0 (2'), and 20.0 K (3')]. Changes in the adsorptive properties upon postsynthetic exchange suggest that the nature, electrostatic properties, mobility, and location of the cations within the framework are crucial for the enhanced structural stability. Overall, these results further confirm the potential of postsynthetic methods (including cation exchange) to obtain PCPs with novel or enhanced physical properties while maintaining unaltered their open-framework structures. PMID:26492551

  1. Cation Exchange in Dynamic 3D Porous Magnets: Improvement of the Physical Properties.

    PubMed

    Grancha, Thais; Acosta, Alvaro; Cano, Joan; Ferrando-Soria, Jesús; Seoane, Beatriz; Gascon, Jorge; Pasán, Jorge; Armentano, Donatella; Pardo, Emilio

    2015-11-16

    We report two novel three-dimensional porous coordination polymers (PCPs) of formulas Li4{Mn4[Cu2(Me3mpba)2]3}·68H2O (2) and K4{Mn4[Cu2(Me3mpba)2]3}·69H2O (3) obtained-via alkali cation exchange in a single-crystal to single-crystal process-from the earlier reported anionic manganese(II)-copper(II) PCP of formula Na4{Mn4[Cu2(Me3mpba)2]3}·60H2O (1) [Me3mpba(4-) = N,N'-2,4,6-trimethyl-1,3-phenylenebis(oxamate)]. This postsynthetic process succeeds where the direct synthesis in solution from the corresponding building blocks fails and affords significantly more robust PCPs with enhanced magnetic properties [long-range 3D magnetic ordering temperatures for the dehydrated phases (1'-3') of 2.0 (1'), 12.0 (2'), and 20.0 K (3')]. Changes in the adsorptive properties upon postsynthetic exchange suggest that the nature, electrostatic properties, mobility, and location of the cations within the framework are crucial for the enhanced structural stability. Overall, these results further confirm the potential of postsynthetic methods (including cation exchange) to obtain PCPs with novel or enhanced physical properties while maintaining unaltered their open-framework structures.

  2. Cation exchange on the nanoscale: an emerging technique for new material synthesis, device fabrication, and chemical sensing.

    PubMed

    Rivest, Jessy B; Jain, Prashant K

    2013-01-01

    Cation exchange is an age-old technique for the chemical conversion of liquids or extended solids by place-exchanging the cations in an ionic material with a different set of cations. The technique is undergoing a major revival with the advent of high-quality nanocrystals: researchers are now able to overcome the limitations in bulk systems and fully exploit cation exchange for materials synthesis and discovery via rapid, low-temperature transformations in the solid state. In this tutorial review, we discuss cation exchange as a promising materials synthesis and discovery tool. Exchange on the nanoscale exhibits some unique attributes: rapid kinetics at room temperature (orders of magnitude faster than in the bulk) and the tuning of reactivity via control of nanocrystal size, shape, and surface faceting. These features make cation exchange a convenient tool for accessing nanocrystal compositions and morphologies for which conventional synthesis may not be established. A simple exchange reaction allows extension of nanochemistry to a larger part of the periodic table, beyond the typical gamut of II-VI, IV-VI, and III-V materials. Cation exchange transformations in nanocrystals can be topotactic and size- and shape-conserving, allowing nanocrystals synthesized by conventional methods to be used as templates for production of compositionally novel, multicomponent, or doped nanocrystals. Since phases and compositions resulting from an exchange reaction can be kinetically controlled, rather than governed by the phase diagram, nanocrystals of metastable and hitherto inaccessible compositions are attainable. Outside of materials synthesis, applications for cation exchange exist in water purification, chemical staining, and sensing. Since nanoscale cation exchange occurs rapidly at room temperature, it can be integrated with sensitive environments such as those in biological systems. Cation exchange is already allowing access to a variety of new materials and processes

  3. Separation of proteins by cation-exchange sequential injection chromatography using a polymeric monolithic column.

    PubMed

    Masini, Jorge Cesar

    2016-02-01

    Since sequential injection chromatography (SIC) emerged in 2003, it has been used for separation of small molecules in diverse samples, but separations of high molar mass compounds such as proteins have not yet been described. In the present work a poly(glycidyl methacrylate-co-ethylene dimethacrylate) (GMA-co-EDMA) monolithic column was prepared by free radical polymerization inside a 2.1-mm-i.d. activated fused silica-lined stainless steel tubing and modified with iminodiacetic acid (IDA). The column was prepared from a mixture of 24% GMA, 16% EDMA, 20% cyclohexanol, and 40% 1-dodecanol (all% as w/w) containing 1% of azobisisobutyronitrile (AIBN) (in relation to monomers). Polymerization was done at 60 °C for 24 h. The polymer was modified with 1.0 M IDA (in 2 M Na2CO3, pH 10.5) at 80 °C for 16 h. Separation of myoglobin, ribonuclease A, cytochrome C, and lysozyme was achieved at pH 7.0 (20 mM KH2PO4/K2HPO4) using a salt gradient (NaCl). Myoglobin was not retained, and the other proteins were separated by a gradient of NaCl created inside the holding coil (4 m of 0.8-mm-i.d. PTFE tubing) by sequential aspiration of 750 and 700 μL of 0.2 and 0.1 M NaCl, respectively. As the flow was reversed toward the column (5 μL s(-1)) the interdispersion of these solutions created a reproducible gradient which separated the proteins in 10 min, with the following order of retention: ribonuclease A < cytochrome C < lysozyme. The elution order was consistent with a cation-exchange mechanism as the retention increased with the isoelectric points.

  4. A new cation-exchange method for accurate field speciation of hexavalent chromium

    USGS Publications Warehouse

    Ball, J.W.; McCleskey, R.B.

    2003-01-01

    A new method for field speciation of Cr(VI) has been developed to meet present stringent regulatory standards and to overcome the limitations of existing methods. The method consists of passing a water sample through strong acid cation-exchange resin at the field site, where Cr(III) is retained while Cr(VI) passes into the effluent and is preserved for later determination. The method is simple, rapid, portable, and accurate, and makes use of readily available, inexpensive materials. Cr(VI) concentrations are determined later in the laboratory using any elemental analysis instrument sufficiently sensitive to measure the Cr(VI) concentrations of interest. The new method allows measurement of Cr(VI) concentrations as low as 0.05 ??g 1-1, storage of samples for at least several weeks prior to analysis, and use of readily available analytical instrumentation. Cr(VI) can be separated from Cr(III) between pH 2 and 11 at Cr(III)/Cr(VI) concentration ratios as high as 1000. The new method has demonstrated excellent comparability with two commonly used methods, the Hach Company direct colorimetric method and USEPA method 218.6. The new method is superior to the Hach direct colorimetric method owing to its relative sensitivity and simplicity. The new method is superior to USEPA method 218.6 in the presence of Fe(II) concentrations up to 1 mg 1-1 and Fe(III) concentrations up to 10 mg 1-1. Time stability of preserved samples is a significant advantage over the 24-h time constraint specified for USEPA method 218.6.

  5. Preliminary studies of an 18-crown-6 ether modified magnetic cation exchange polymer in rapid (90)Sr bioassay.

    PubMed

    Hrdina, Amy; Lai, Edward; Li, Chunsheng; Sadi, Baki; Kramer, Gary

    2011-08-01

    A cation exchange polymer resin embedded with magnetic nanoparticles and modified with crown ether was developed for urinalysis to rapidly monitor levels of (90)Sr exposure in humans who have been involved in a nuclear event. Invention of the resin matrix of 2-acrylamido-2-methyl-1-propanesulfonic acid cross-linked with divinylbenzene incorporated a Sr(2+) chelating agent, di-tert-butyl-cyclohexano-18-crown-6 through surface immobilization using a molecular modifier 1-octanol. The performance of these magnetic cation exchange resin particles was investigated by separating (90)Sr in the presence of (90)Y progeny. Masking agents and precipitants were examined to ascertain that sodium hydroxide at pH 7.5 was capable of selectively removing 89 ± 2% (90)Y before subsequent (90)Sr uptake. Preliminary investigations in rapid urinalysis were successful in isolating 83 ± 2% (90)Sr when pH was optimized to 9, with a sample turnover time <2 h, which is promising for radiological emergencies.

  6. Effect of blastfurnace slag addition to Portland cement for cationic exchange resins encapsulation

    NASA Astrophysics Data System (ADS)

    Lafond, E.; Cau Dit Coumes, C.; Gauffinet, S.; Chartier, D.; Le Bescop, P.; Stefan, L.; Nonat, A.

    2013-07-01

    In the nuclear industry, cement-based materials are extensively used to encapsulate spent ion exchange resins (IERs) before their final disposal in a repository. It is well known that the cement has to be carefully selected to prevent any deleterious expansion of the solidified waste form, but the reasons for this possible expansion are not clearly established. This work aims at filling the gap. The swelling pressure of IERs is first investigated as a function of ions exchange and ionic strength. It is shown that pressures of a few tenths of MPa can be produced by decreases in the ionic strength of the bulk solution, or by ion exchanges (2Na+ instead of Ca2+, Na+ instead of K+). Then, the chemical evolution of cationic resins initially in the Na+ form is characterized in CEM I (Portland cement) and CEM III (Portland cement + blastfurnace slag) cements at early age and an explanation is proposed for the better stability of CEM III material.

  7. Effect of cation-exchange pretreatment of aqueous soil extracts on the gas chromatographic-mass spectrometric determination of nerve agent hydrolysis products after tert.-butyldimethylsilylation.

    PubMed

    Kataoka, M; Tsunoda, N; Ohta, H; Tsuge, K; Takesako, H; Seto, Y

    1998-10-23

    The efficiency of pretreatment of aqueous soil extracts using a cation-exchange resin has been investigated by gas chromatographic-mass spectrometric (GC-MS) determination of nerve agent hydrolysis products after tert.-butyldimethylsilyl (TBDMS) derivatization. An aqueous solution containing methylphosphonic acid (MPA) and its monoalkyl esters, ethyl methylphosphonic acid, isopropyl methylphosphonic acid and pinacolyl methylphosphonic acid, was dried, and these phosphonic acids were derivatized with N-methyl-N-(tert.-butyldimethylsilyl)trifluoro-acetamide and analyzed by GC-MS. The yields of TBDMS derivatives were significantly decreased by the addition of calcium and magnesium ions to an aqueous solution (approximately 0.5 mM) before derivatization. The extent of lowered yields was related to the hydrophilicity of phosphonic acids. MPA and its monoalkyl esters were spiked into soil samples (sand, alluvial soil and volcanic ash soil), extracted with distilled water, dried, silylated and applied to GC-MS. The yields of TBDMS derivatives of monoalkyl esters from soil samples were low (3-42%) and MPA derivative was scarcely detected (yield: < 0.7%). By desalting the aqueous soil extract by passage through a strong cation-exchange resin, the yields of TBDMS derivatives of monoalkyl esters were significantly improved (12-69%) and MPA derivative was detected (yield: 2-36%). The extent of improved yields was related to the concentrations of divalent metal cations in aqueous soil extracts. In combination with desalting by the cation-exchange resin, GC-MS after TBDMS derivatization enables detection of nerve agent hydrolysis products in soils at sub-ppm (0.2 microgram/g) concentrations. PMID:9818434

  8. Erionite-Na upon heating: dehydration dynamics and exchangeable cations mobility.

    PubMed

    Ballirano, Paolo; Pacella, Alessandro

    2016-01-01

    Erionite is a fibrous zeolite significantly more tumorigenic than crocidolite asbestos upon inhalation. In recent years, several papers have been published aimed at characterizing from the crystal-chemical point of view erionite fibres. As their toxicity has been ascribed to Fe acquired within the human body, studies aimed at characterizing the iron topochemistry have also been published, suggesting a possible important role played by the ionic exchange properties and cations mobility of this zeolite on developing carcinogenicity. Here we report the analysis results of the thermal behaviour of erionite-Na, which has been found to deviate significantly from that of erionite-K. This result is in contrast with the current scientific view that differences in weighted ionic potential, Si/Al ratio and size of exchangeable cations result in significantly different thermal behaviours, all those parameters being nearly identical or very similar in both species. The different mobility of the extraframework cations observed in erionite samples with dissimilar chemistry is of particular interest within the frame of the hypothesis that their biological activity could depend, apart from surface interactions, also on bulk effects. PMID:26948139

  9. Erionite-Na upon heating: dehydration dynamics and exchangeable cations mobility

    NASA Astrophysics Data System (ADS)

    Ballirano, Paolo; Pacella, Alessandro

    2016-03-01

    Erionite is a fibrous zeolite significantly more tumorigenic than crocidolite asbestos upon inhalation. In recent years, several papers have been published aimed at characterizing from the crystal-chemical point of view erionite fibres. As their toxicity has been ascribed to Fe acquired within the human body, studies aimed at characterizing the iron topochemistry have also been published, suggesting a possible important role played by the ionic exchange properties and cations mobility of this zeolite on developing carcinogenicity. Here we report the analysis results of the thermal behaviour of erionite-Na, which has been found to deviate significantly from that of erionite-K. This result is in contrast with the current scientific view that differences in weighted ionic potential, Si/Al ratio and size of exchangeable cations result in significantly different thermal behaviours, all those parameters being nearly identical or very similar in both species. The different mobility of the extraframework cations observed in erionite samples with dissimilar chemistry is of particular interest within the frame of the hypothesis that their biological activity could depend, apart from surface interactions, also on bulk effects.

  10. Chabazite: stable cation-exchanger in hyper alkaline concrete pore water.

    PubMed

    Van Tendeloo, Leen; Wangermez, Wauter; Kurttepeli, Mert; de Blochouse, Benny; Bals, Sara; Van Tendeloo, Gustaaf; Martens, Johan A; Maes, André; Kirschhock, Christine E A; Breynaert, Eric

    2015-02-17

    To avoid impact on the environment, facilities for permanent disposal of hazardous waste adopt multibarrier design schemes. As the primary barrier very often consists of cement-based materials, two distinct aspects are essential for the selection of suitable complementary barriers: (1) selective sorption of the contaminants in the repository and (2) long-term chemical stability in hyperalkaline concrete-derived media. A multidisciplinary approach combining experimental strategies from environmental chemistry and materials science is therefore essential to provide a reliable assessment of potential candidate materials. Chabazite is typically synthesized in 1 M KOH solutions but also crystallizes in simulated young cement pore water, a pH 13 aqueous solution mainly containing K(+) and Na(+) cations. Its formation and stability in this medium was evaluated as a function of temperature (60 and 85 °C) over a timeframe of more than 2 years and was also asessed from a mechanistic point of view. Chabazite demonstrates excellent cation-exchange properties in simulated young cement pore water. Comparison of its Cs(+) cation exchange properties at pH 8 and pH 13 unexpectedly demonstrated an increase of the KD with increasing pH. The combined results identify chabazite as a valid candidate for inclusion in engineered barriers for concrete-based waste disposal.

  11. Crystal structure and cation exchanging properties of a novel open framework phosphate of Ce (IV)

    NASA Astrophysics Data System (ADS)

    Bevara, Samatha; Achary, S. N.; Patwe, S. J.; Sinha, A. K.; Mishra, R. K.; Kumar, Amar; Kaushik, C. P.; Tyagi, A. K.

    2016-05-01

    Herein we report preparation, crystal structure and ion exchanging properties of a new phosphate of tetravalent cerium, K2Ce(PO4)2. A monoclinic structure having framework type arrangement of Ce(PO4)6 units formed by CeO8 square-antiprism and PO4 tetrahedra is assigned for K2Ce(PO4)2. The K+ ions are occupied in the channels formed by the Ce(PO4)6 and provide overall charge neutrality. The unique channel type arrangements of the K+ make them exchangeable with other cations. The ion exchanging properties of K2Ce(PO4)2 has been investigated by equilibrating with solution of 90Sr followed by radiometric analysis. In optimum conditions, significant exchange of K+ with Sr2+ with Kd ~ 8000 mL/g is observed. The details of crystal structure and ion exchange properties are explained and a plausible mechanism for ion exchange is presented.

  12. Process and apparatus for the production of Bi-213 cations

    DOEpatents

    Horwitz, E.P.; Hines, J.J.; Chiarizia, R.; Dietz, M.

    1998-12-29

    A process for producing substantially impurity-free Bi-213 cations is disclosed. An aqueous acid feed solution containing Ac-225 cations is contacted with an ion exchange medium to bind the Ac-225 cations and form an Ac-225-laden ion exchange medium. The bound Ac-225 incubates on the ion exchange medium to form Bi-213 cations by radioactive decay. The Bi-213 cations are then recovered from the Ac-225-laden ion exchange medium to form a substantially impurity-free aqueous Bi-213 cation acid solution. An apparatus for carrying out this process is also disclosed. 7 figs.

  13. Process and apparatus for the production of BI-213 cations

    DOEpatents

    Horwitz, E. Philip; Hines, John J.; Chiarizia, Renato; Dietz, Mark

    1998-01-01

    A process for producing substantially impurity-free Bi-213 cations is disclosed. An aqueous acid feed solution containing Ac-225 cations is contacted with an ion exchange medium to bind the Ac-225 cations and form an Ac-225-laden ion exchange medium. The bound Ac-225 incubates on the ion exchange medium to form Bi-213 cations by radioactive decay. The Bi-213 cations are then recovered from the Ac-225-laden ion exchange medium to form a substantially impurity-free aqueous Bi-213 cation acid solution. An apparatus for carrying out this process is also disclosed.

  14. Emerging roles of alkali cation/proton exchangers in organellar homeostasis

    PubMed Central

    Orlowski, John; Grinstein, Sergio

    2016-01-01

    The regulated movement of monovalent cations such as H+, Li+, Na+ and K+ across biological membranes influences a myriad of cellular processes and is fundamental to all living organisms. This is accomplished by a multiplicity of ion channels, pumps and transporters. Our insight into their molecular, cellular and physiological diversity has increased greatly in the past few years with the advent of genome sequencing, genetic manipulation and sophisticated imaging techniques. One of the revelations from these studies is the emergence of novel alkali cation/protons exchangers that are present in endomembranes, where they function to regulate not only intraorganellar pH but also vesicular biogenesis, trafficking and other aspects of cellular homeostasis. PMID:17646094

  15. Carbon dioxide and nitrogen adsorption on cation-exchanged SSZ-13 zeolites.

    PubMed

    Pham, Trong D; Liu, Qingling; Lobo, Raul F

    2013-01-15

    Samples of high-silica SSZ-13, ion exchanged with protons and alkali-metal cations Li(+), Na(+), and K(+), were investigated using adsorption isotherms of CO(2) and N(2). The results show that Li-, Na-SSZ-13 have excellent CO(2) capacity at ambient temperature and pressure; in general, Li-SSZ-13 shows the highest capacity for N(2), CO(2) particularly in the low-pressure region. The effect of cation type and Si/Al ratio (6 and 12) on the adsorption properties was investigated through analysis of adsorption isotherms and heats of adsorption. The separation of CO(2) in a flue gas mixture was evaluated for these adsorbents in the pressure swing adsorption and vacuum pressure adsorption processes. PMID:23249267

  16. Effects of exchanged cation and layer charge on the sorption of water and EGME vapors on montmorillonite clays

    USGS Publications Warehouse

    Chiou, C.T.; Rutherford, D.W.

    1997-01-01

    The effects of exchanged cation and layer charge on the sorption of water and ethylene glycol monoethyl ether (EGME) vapors on montmorillonite have been studied on SAz-1 and SWy-1 source clays, each exchanged respectively with Ca, Na, K, Cs and tetramethylammonium (TMA) cations. The corresponding lattice expansions were also determined, and the corresponding N2 adsorption data were provided for comparison. For clays exchanged with cations of low hydrating powers (such as K, Cs and TMA), water shows a notably lower uptake than does N2 at low relative pressures (P/P0). By contrast, EGME shows higher uptakes than N2 on all exchanged clays at all P/P0. The anomaly for water is attributed to its relatively low attraction for siloxane surfaces of montmorillonite because of its high cohesive energy density. In addition to solvating cations and expanding interlayers, water and EGME vapors condense into small clay pores and interlayer voids created by interlayer expansion. The initial (dry) interlayer separation varies more significantly with cation type than with layer charge; the water-saturated interlayer separation varies more with cation type than the EGME-saturated interlayer separation. Because of the differences in surface adsorption and interlayer expansion for water and EGME, no general correspondence is found between the isotherms of water and EGME on exchanged clays, nor is a simple relation observed between the overall uptake of either vapor and the cation solvating power. The excess interlayer capacities of water and of EGME that result from lattice expansion of the exchanged clays are estimated by correcting for amounts of vapor adsorption on planar clay surfaces and of vapor condensation into intrinsic clay pores. The resulting data follow more closely the relative solvating powers of the exchanged cations.

  17. Reducing the Cation Exchange Capacity of Lithium Clay to Form Better Dispersed Polymer-Clay Nanocomposites

    NASA Technical Reports Server (NTRS)

    Liang, Maggie

    2004-01-01

    Polymer-clay nanocomposites have exhibited superior strength and thermo- oxidative properties as compared to pure polymers for use in air and space craft; however, there has often been difficulty completely dispersing the clay within the matrices of the polymer. In order to improve this process, the cation exchange capacity of lithium clay is first lowered using twenty-four hour heat treatments of no heat, 130 C, 150 C, or 170 C to fixate the lithium ions within the clay layers so that they are unexchangeable. Generally, higher temperatures have generated lower cation exchange capacities. An ion exchange involving dodecylamine, octadecylamine, or dimethyl benzidine (DMBZ) is then employed to actually expand the clay galleries. X-ray diffraction and transmission electron microscopy can be used to determine whether the clay has been successfully exfoliated. Finally, resins of DMBZ with clay are then pressed into disks for characterization using dynamic mechanical analyzer and oven- aging techniques in order to evaluate their glass transition, modulus strength, and thermal-oxidative stability in comparison to neat DMBZ. In the future, they may also be tested as composites for flexural and laminar shear strength.

  18. Use of Cation Exchange Resins for Production of U{sub 3}O{sub 8} Suitable for the Al-U{sub 3}O{sub 8} Powder Metallurgy Process

    SciTech Connect

    Mosley, W.C.

    2001-09-17

    This report describes the production of U{sub 3}O{sub 8} powders from three types of cation exchange resins: Dowex 50W, a strong acid, sulfonate resin; AG MP-50, a macroporous form of sulfonate resin; and Bio-Rex 70, a weak acid, carboxylic resin.

  19. Intracellular acidification-induced alkali metal cation/H+ exchange in human neutrophils

    PubMed Central

    1987-01-01

    Pretreatment of isolated human neutrophils (resting pHi congruent to 7.25 at pHo 7.40) with 30 mM NH4Cl for 30 min leads to an intracellular acidification (pHi congruen to 6.60) when the NH4Cl prepulse is removed. Thereafter, in 140 mM Na+ medium, pHi recovers exponentially with time (initial rate, approximately 0.12 pH/min) to reach the normal resting pHi by approximately 20 min, a process that is accomplished mainly, if not exclusively, though an exchange of internal H+ for external Na+. This Na+/H+ countertransport is stimulated by external Na+ (Km congruent to 21 mM) and by external Li+ (Km congruent to 14 mM), though the maximal transport rate for Na+ is about twice that for Li+. Both Na+ and Li+ compete as substrates for the same translocation sites on the exchange carrier. Other alkali metal cations, such as K+, Rb+, or Cs+, do not promote pHi recovery, owing to an apparent lack of affinity for the carrier. The exchange system is unaffected by ouabain or furosemide, but can be competitively inhibited by the diuretic amiloride (Ki congruent to 8 microM). The influx of Na+ or Li+ is accompanied by an equivalent counter-reflux of H+, indicating a 1:1 stoichiometry for the exchange reaction, a finding consistent with the lack of voltage sensitivity (i.e., electroneutrality) of pHi recovery. These studies indicate that the predominant mechanism in human neutrophils for pHi regulation after intracellular acidification is an amiloride-sensitive alkali metal cation/H+ exchange that shares a number of important features with similar recovery processes in a variety of other mammalian cell types. PMID:3694176

  20. [Cation exchanges during the process of Cd(2+) absorption by Alfalfa in aqueous solutions].

    PubMed

    Li, Yue-Peng; Yin, Hua; Ye, Jin-Shao; Peng, Hua; Qin, Hua-Ming; Long, Yan; He, Bao-Yan; Zhang, Na; Tong, Yao; Peng, Su-Fen

    2011-11-01

    A hydroponic experiment was conducted to investigate the cation exchanges during the process of Cd2+ absorption by Alfalfa in aqueous solution. The absorption efficiency of Alfalfa plants with 0-10 mg x L(-1) Cd2+ treatments, changes of Na+, K+, Mg2+, Ca2+ and NH4(+) concentration, and the variation of pH values at different absorption time (0, 1, 2, 4, 8, 12, 24 and 72 h) were studied separately. The multiple linear regressions between Cd2+ absorption and cation variation were analyzed. The results indicated that when Cd2+ concentrations were 0.1, 1, 5, 10 mg x L(-1), the absorption efficiencies of Cd2+ by Alfalfa after 72 h were 85.86%, 52.14%, 15.97% and 7.81%. Cation exchange was involved in the removal of Cd2+ by Alfalfa in aqueous solution. Except for NH4(+), the concentrations of cationic metals Na+, K+, Mg2+ and Ca2+ in aqueous solution increased over time, which increased 11.30% - 61.72%, 21.44% - 98.73%, 24.09% - 8.90% and 37.04% - 191.96%, respectively. Kinetic studies illuminated that the release of Na+, K+, Mg2+ and Ca2+ by Alfalfa in Cd2+ solution with initial concentrations of 0, 0. 1, 1, 5, 10 mg x L(-1) best fitted pseudo-second-order equation,while the NH4(+) release fitted this model when Cd2+ concentrations were 1, 5, 10 mg x L(-1). The gradual decrease of pH during adsorption of Cd2+ by Alfalfa was observed. As the competition ion of Cd2+, H+ might affect the capacity of Alfalfa root system to absorb Cd2+. The ternary linear equation results demonstrated that the content of Cd2+ absorption by Alfalfa strongly related with the release of Ca2+, Mg2+, Na+. And this exchange mainly occurred among Cd2+ and divalent cations. PMID:22295633

  1. The use of some ion-exchange sorbing tracer cations in in-situ experiments in high saline groundwaters

    SciTech Connect

    Byegaard, J.; Skarnemark, G.; Skaalberg, M.

    1995-12-31

    The possibility to use alkali metals and alkaline earth metals as slightly sorbing tracers in in-situ sorption experiments in high saline groundwaters has been investigated. The cation exchange characteristics of granite and some fracture minerals (chlorite and calcite) have been studied using the proposed cations as tracers. The results show low Kd`s for Na, Ca and Sr ({approximately}0.1 ml/g), while the sorption is higher for the more electropositive cations (Rb, Cs and Ba). A higher contribution of irreversible sorption can also be observed for the latter group of cations. For calcite the sorption of all the tracers, except Ca, is lower compared to the corresponding sorption to granite and chlorite. Differences in selectivity coefficients and cation exchange capacity are obtained when using different size fractions of crushed granite. The difference is even more pronounced when comparing crushed granite to intact granite.

  2. Preparation and evaluation of rigid porous polyacrylamide-based strong cation-exchange monolithic columns for capillary electrochromatography.

    PubMed

    Dong, Jing; Ou, Junjie; Dong, Xiaoli; Wu, Renan; Ye, Mingliang; Zou, Hanfa

    2007-11-01

    A CEC monolithic column with strong cation-exchange (SCX) stationary phase based on hydrophilic monomers was prepared by in situ polymerization of acrylamide, methylenebisacrylamide, and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) in a complete organic binary porogenic solvent consisting of DMSO and dodecanol. The sulfonic groups provided by the monomer AMPS on the surface of the stationary phase generate an EOF from anode to cathode, and serve as an SCX stationary phase at the same time. The monolithic stationary phase exhibited normal-phase chromatographic behavior for neutral analytes. For charged analytes, electrostatic interaction/repulsion with the monolith was observed. The strong SCX monolithic column has been successfully employed in the electrochromatographic separation of basic drugs, peptides, and alkaloids extracted from natural products.

  3. Quantitative Analysis of Cations in Solutions Using ion Exchange Filter Paper by X-ray Fluorescence Spectrometry

    NASA Astrophysics Data System (ADS)

    Taketani, Y.; Fujimaki, H.

    2007-12-01

    The strong acid cation exchange filter, CP-1, were applied to X-ray fluorescence (XRF) for trace elements in aqueous solution. In this study, the objective elements were Cu, Zn, Pb, and Cd. The measurement of the X-ray intensity determined the optimum methods of XRF analyses using the CP-1 filter. The optimum area that sample solutions penetrated was inside the determining area. The proper material to underlay CP-1 filter was glass bead. The calibration curves that determined by this study calculated the limit values of determination. These values were 0.72 micro gram for Cu and Zn. The method of separation and concentration using the CP-1 filter enable the quantitative analyses of trace heavy metals easily.

  4. Preparation and evaluation of rigid porous polyacrylamide-based strong cation-exchange monolithic columns for capillary electrochromatography.

    PubMed

    Dong, Jing; Ou, Junjie; Dong, Xiaoli; Wu, Renan; Ye, Mingliang; Zou, Hanfa

    2007-11-01

    A CEC monolithic column with strong cation-exchange (SCX) stationary phase based on hydrophilic monomers was prepared by in situ polymerization of acrylamide, methylenebisacrylamide, and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) in a complete organic binary porogenic solvent consisting of DMSO and dodecanol. The sulfonic groups provided by the monomer AMPS on the surface of the stationary phase generate an EOF from anode to cathode, and serve as an SCX stationary phase at the same time. The monolithic stationary phase exhibited normal-phase chromatographic behavior for neutral analytes. For charged analytes, electrostatic interaction/repulsion with the monolith was observed. The strong SCX monolithic column has been successfully employed in the electrochromatographic separation of basic drugs, peptides, and alkaloids extracted from natural products. PMID:17924588

  5. Effects of Forest Succession on Exchangeable Cation Concentrations and Nitrogen Mineralization Rates in Soils Following Logging of Eastern Hemlock Forest, Whately, Massachusetts

    NASA Astrophysics Data System (ADS)

    Rhodes, A. L.; Sweezy, T.; Zukswert, J. M.; Dwyer, C. H.

    2012-12-01

    Ecological forest successions associated with invasive species and human disturbance may alter biogeochemical cycles within New England forests. Spread of the invasive insect hemlock woolly adelgid (Adelges tsugae) to eastern North America is causing mortality of the eastern hemlock (Tsuga canadensis), prompting salvage logging. Regrowth by deciduous hardwood trees is often observed. To evaluate whether changes in nutrient cycling could be altered by forest succession, we investigated exchangeable cation chemistry and nitrogen mineralization rates for soil in a mature, eastern hemlock forest and in a juvenile black birch (Betula lenta) forest in western MA. Eastern hemlock on this property was selectively logged 20 years ago, with black birch regrowth succeeding hemlock. We measured soil pH, exchangeable acidity (Al3+ and H+), exchangeable base cations (Ca2+, Mg2+, Na+, and K+), and nitrogen mineralization rates of organic and mineral horizons for 7 incubation periods between May 2011 - July 2012. We also measured the cation exchange capacity and nitrogen mineralization rates of soils from May - July 2012 (2 incubations) in a mature deciduous forest composed primarily of black birch. At each field site, 7 soil cores were collected. Soil horizons (organic and mineral) were separated and homogenized, and 3 replicates of each composite sample were analyzed for soil geochemistry. Organic soils within the juvenile black birch plot (BB) exhibit a low pH (4.3) similar to hemlock organic soils (HEM, pH=4.2). Surprisingly, exchangeable Al3+—the dominant cation in both plots—is significantly greater in organic soils at BB than at HEM (p<.001), and base saturation is less at BB (29%) than at HEM (46%, p<0.001) due to less Ca2+. There are no significant differences in the exchangeable cation chemistry of the mineral horizons at both sites, suggesting that the acidity difference of organic matter is not due to different soil mineralogy. In comparison, organic soil at the

  6. Quantification of melamine in human urine using cation-exchange based high performance liquid chromatography tandem mass spectrometry.

    PubMed

    Panuwet, Parinya; Nguyen, Johnny V; Wade, Erin L; D'Souza, Priya E; Ryan, P Barry; Barr, Dana Boyd

    2012-03-01

    Melamine and cyanuric acid have been implicated as adulterants in baby formula in China and pet foods in North America. In China, the effect of melamine or melamine-cyanuric acid adulteration lead to kidney stone development and acute renal failure in thousands of Chinese infants. A selective and sensitive analytical method was developed to measure melamine in human urine in order to evaluate the extent of potential health implications resulting from the consumption of these types of adulterated products in the general US population. This method involves extracting melamine from human urine using cation-exchange solid-phase extraction, chromatographically separating it from its urinary matrix co-extractants on a silica-based, strong-cation exchange analytical column using high performance liquid chromatography, and analysis using positive mode electrospray ionization tandem mass spectrometry. Quantification was performed using modified, matrix-based isotope dilution calibration covering the concentration range of 0.50-100 ng/mL. The limit of detection, calculated using replicates of blank and low level spiked samples, was 0.66 ng/mL and the relative standard deviations were between 6.89 and 14.9%. The relative recovery of melamine was 101-106%. This method was tested for viability by analyzing samples collected from the general US population. Melamine was detected in 76% of the samples tested, with a geometric mean of 2.37 ng/mL, indicating that this method is suitable for reliably detecting background exposures to melamine or other chemicals from which it can be derived. PMID:22309774

  7. Proton-sensitive cation channels and ion exchangers in ischemic brain injury: new therapeutic targets for stroke?

    PubMed Central

    Leng, Tiandong; Shi, Yejie; Xiong, Zhi-Gang; Sun, Dandan

    2014-01-01

    Ischemic brain injury results from complicated cellular mechanisms. The present therapy for acute ischemic stroke is limited to thrombolysis with the recombinant tissue plasminogen activator (rtPA) and mechanical recanalization. Therefore, a better understanding of ischemic brain injury is needed for the development of more effective therapies. Disruption of ionic homeostasis plays an important role in cell death following cerebral ischemia. Glutamate receptor-mediated ionic imbalance and neurotoxicity have been well established in cerebral ischemia after stroke. However, non-NMDA receptor-dependent mechanisms, involving acid-sensing ion channel 1a (ASIC1a), transient receptor potential melastatin 7 (TRPM7), and Na+/H+ exchanger isoform 1 (NHE1), have recently emerged as important players in the dysregulation of ionic homeostasis in the CNS under ischemic conditions. These H+-sensitive channels and/or exchangers are expressed in the majority of cell types of the neurovascular unit. Sustained activation of these proteins causes excessive influx of cations, such as Ca2+, Na+, and Zn2+, and leads to ischemic reperfusion brain injury. In this review, we summarize recent pre-clinical experimental research findings on how these channels/exchangers are regulated in both in vitro and in vivo models of cerebral ischemia. The blockade or transgenic knockdown of these proteins was shown to be neuroprotective in these ischemia models. Taken together, these non-NMDA receptor-dependent mechanisms may serve as novel therapeutic targets for stroke intervention. PMID:24467911

  8. Elucidating the Higher Stability of Vanadium (V) Cations in Mixed Acid Based Redox Flow Battery Electrolytes

    SciTech Connect

    Vijayakumar, M.; Wang, Wei; Nie, Zimin; Sprenkle, Vincent L.; Hu, Jian Z.

    2013-11-01

    The Vanadium (V) cation structures in mixed acid based electrolyte solution were analysed by density functional theory (DFT) based computational modelling and 51V and 35Cl Nuclear Magnetic Resonance (NMR) spectroscopy. The Vanadium (V) cation exists as di-nuclear [V2O3Cl2.6H2O]2+ compound at higher vanadium concentrations (≥1.75M). In particular, at high temperatures (>295K) this di-nuclear compound undergoes ligand exchange process with nearby solvent chlorine molecule and forms chlorine bonded [V2O3Cl2.6H2O]2+ compound. This chlorine bonded [V2O3Cl2.6H2O]2+ compound might be resistant to the de-protonation reaction which is the initial step in the precipitation reaction in Vanadium based electrolyte solutions. The combined theoretical and experimental approach reveals that formation of chlorine bonded [V2O3Cl2.6H2O]2+ compound might be central to the observed higher thermal stability of mixed acid based Vanadium (V) electrolyte solutions.

  9. Pullulan Production by Aureobasidium pullulans ATCC 201253 Cells Adsorbed onto Cellulose Anion and Cation Exchangers

    PubMed Central

    West, Thomas P.

    2012-01-01

    The anion exchanger phosphocellulose and the cation exchanger triethylaminoethyl cellulose were used to immobilize cells of the fungus Aureobasidium pullulans ATCC 201253 and the adsorbed cells were subsequently investigated for their ability to produce the polysaccharide pullulan using batch fermentation. The cells adsorbed on the triethylaminoethyl cellulose at pH 7.5 produced higher pullulan levels than those cells immobilized on phosphocellulose at pH 4.0 for 2 cycles of 168 h at 30 °C. Relative to the initial cycle of 168 h, pullulan production by the cells immobilized on the triethylaminoethyl cellulose decreased slightly after 168 h of the second production cycle while pullulan production by the phosphocellulose-immobilized cells remained about the same after 168 h of the second production cycle. PMID:23762749

  10. Chromatographic cation exchange separation of decigram quantities of californium and other transplutonium elements

    SciTech Connect

    Benker, D.E.; Chattin, F.R.; Collins, E.D.; Knauer, J.B.; Orr, P.B.; Ross, R.G.; Wiggins, J.T.

    1981-01-01

    Decigram quantities of highly radioactive transplutonium elements are routinely partitioned at TRU by chromatographic elution from cation resin using AHIB eluents. Batch runs containing up to 200 mg of /sup 252/Cf can be made in about 5 h (2 h to load the feed and 3 h for the elution), with two high-pressure ion exchange columns, a small one for the initial loading of the feed and a large one for the elution. The separations achieved in the column are preserved by routing the column effluent through an alpha detector and using the response from the detector to select appropriate product fractions. The high-pressure ion exchange process has been reliable and relatively easy to operate; therefore it will continue to be used for partitioning transplutonium elements at TRU. 3 figures, 1 table.

  11. Composition of exchangeable bases and acidity in soils of the Crimean Mountains

    NASA Astrophysics Data System (ADS)

    Kostenko, I. V.

    2015-08-01

    Acid forest and mountainous meadow soils of the Crimean Mountains were studied. The amount of hydrogen and aluminum ions extracted from these soils depended on the pH of extracting agents. The maximum values of the soil acidity were obtained upon the extraction with a strongly alkaline solution of sodium acetate in 0.05 N NaOH. The application of this extractant made it possible to determine the total exchange acidity, the total amount of extractable aluminum, and the total cation exchange capacity of the soils after the extraction of all the acidic components from them. The values of these characteristics were significantly higher than the values of the potential acidity and cation exchange capacity obtained by the routine analytical methods. Hydrogen predominated among the acidic components of the exchange acidity in the humus horizons, whereas aluminum predominated among them in the underlying mineral horizons. Hydrothermic conditions and the character of vegetation and parent materials were the major factors affecting the relationships between bases and acidic components in the soil adsorption complex.

  12. Layered polyaniline composites with cation-exchanging properties for positive electrodes of rechargeable lithium batteries

    SciTech Connect

    Morita, Masayuki; Miyazaki, Seijiro; Ishikawa, Masashi; Matsuda, Yoshiharu . Dept. of Applied Chemistry and Chemical Engineering); Tajima, Hidehiko . Nagasaki Research and Development Center); Adachi, Kazuyuki; Anan, Fumimiasa . Research Lab.)

    1995-01-01

    Layered polyaniline/polyaniline-polyanion composite films (PAn-X/PAn-PA) were synthesized by electrochemical oxidation of aniline in aqueous acid solutions (HCl, HClO[sub 4]) followed by polymerization in poly(styrene-4-sulfonic acid) (PSSH) solutions. The films consist of inner polyaniline (PAn) layers doped with smaller size anions (X) and outer PSS-doped PAn layers. The resulting films showed high redox activities with cation-transfer properties in organic electrolyte solutions. The improved charge/discharge characteristics of the composite films gave an expectation of higher energy density for the full cell with lithium negative electrode.

  13. Application of mixed-mode, solid-phase extraction in environmental and clinical chemistry. Combining hydrogen-bonding, cation-exchange and Van der Waals interactions

    USGS Publications Warehouse

    Mills, M.S.; Thurman, E.M.; Pedersen, M.J.

    1993-01-01

    Silica- and styrene-divinylbenzene-based mixed-mode resins that contain C8, C18 and sulphonated cation-exchange groups were compared for their efficiency in isolation of neutral triazine compounds from water and of the basic drug, benzoylecgonine, from urine. The triazine compounds were isolated by a combination of Van der Waals and hydrogen-bonding interactions, and benzoylecgonine was isolated by Van der Waals interactions and cation exchange. All analytes were eluted with a polar organic solvent contaning 2% ammonium hydroxide. Larger recoveries (95%) were achieved on copolymerized mixed-mode resins where C18 and sulfonic acid are in closer proximity than on 'blended' mixed-mode resins (60-70% recovery).

  14. Cation-exchange chromatography of peptides on poly(2-sulfoethyl aspartamide)-silica.

    PubMed

    Alpert, A J; Andrews, P C

    1988-06-29

    A strong cation-exchange material, poly(2-sulfoethyl aspartamide)-silica (PolySULFOETHYL Aspartamide) was developed for purification and analysis of peptides by high-performance liquid chromatography. All peptides examined were retained at pH 3, even when the amino terminus was the only basic group. Peptides were eluted in order of increasing number of basic residues with a salt gradient. Capacity was high, as was selectivity and column efficiency. This new column material displays modest mixed-mode effects, allowing the resolution of peptides having identical charges at a given pH. The selectivity can be manipulated by the addition of organic solvent to the mobile phases; this increases the retention of some peptides and decreases the retention of others. The retention in any given case may reflect a combination of steric factors and non-electrostatic interactions. Selectivity was complementary to that of reversed-phase chromatography (RPC) materials. Excellent purifications were obtained by sequential use of PolySULFOETHYL Aspartamide and RPC columns for purification of peptides from crude tissue extracts. The new cation exchanger is quite promising as a supplement to RPC for general peptide chromatography. PMID:2844843

  15. Cation Exchange Synthesis and Unusual Resistive Switching Behaviors of Ag2Se Nanobelts.

    PubMed

    Guo, Zheng; Li, Min-Qiang; Liu, Jin-Huai; Huang, Xing-Jiu

    2015-12-16

    Ag2Se nanobelts are prepared through employing ZnSe nanobelts as templates via a facile cation exchange approach. The templates are derived from precursor ZnSe·0.5N2 H4 nanobelts, which are synthesized by a simple hydrothermal method. As-synthesized precursor nanobelts are with 200 nm in width and several hundreds of micrometers in length. Annealed in N2 , they are transformed into ZnSe nanobelts with preserving their initial morphology. Following with a complete replacement of Zn(2+) by Ag(+), Ag2Se nanobelts with single crystalline are obtained via a cation-exchange reaction. Combined with the Langmuir-Blodgett assembly technique, regular films of ZnSe nanobelts can be achieved on transparent glass substrates and Si wafers with interdigital Au electrode arrays. Further, the optical and electrical evolutions are investigated from ZnSe nanobelts to Ag2 Se nanobelts. Finally, the resistive switching characteristic are carefully explored for Ag2Se nanobelts regularly arranged on interdigital Au microelectrodes. The results indicate that it is analogous to complementary resistive switching behaviors, which is different from that of traditional two terminal devices about previously reported Ag2Se. In order to clarify this phenomenon, a possible mechanism has been proposed and indirectly demonstrated through in situ SEM (scanning electron microscropy) observation.

  16. Numerical simulation of cesium and strontium migration through sodium bentonite altered by cation exchange with groundwater components

    SciTech Connect

    Jacobsen, J.S.; Carnahan, C.L.

    1988-10-01

    Numerical simulations have been used to investigate how spatial and temporal changes in the ion exchange properties of bentonite affect the migration of cationic fission products from high-level waste. Simulations in which fission products compete for exchange sites with ions present in groundwater diffusing into the bentonite are compared to simulations in which the exchange properties of bentonite are constant. 12 refs., 3 figs., 2 tabs.

  17. Effect of ionophores on the rate of intramolecular cation exchange in durosemiquinone ion pairs

    NASA Technical Reports Server (NTRS)

    Eastman, M. P.; Bruno, G. V.; Mcguyer, C. A.; Gutierrez, A. R.; Shannon, J. M.

    1979-01-01

    The effects of the ionophores 15-crown-5 (15C5), 18-crown-6 (18C6), dibenzo-18-crown-6 (DBC) and cryptand 222 (C222) on intramolecular cation exchange in ion pairs of the sodium salt of the durosemiquinone anion in benzene solution are investigated. Electron paramagnetic resonance spectra of the 18C6 and 15C5 complexes with durosemiquinone reduced by contact with a sodium mirror show an alternating line width which indicates that the sodium ion is being exchanged between equivalent sites near the oxygens of the semiquinone with activation energies of 8.7 and 6.0 kcal/mole and Arrhenius preexponential factors of 9 x 10 to the 12th/sec and 10 to the 12th/sec, respectively. Spectra obtained for the DBC complexes show no evidence of exchange, while those of C222 indicate rapid exchange. It is also noted that the hyperfine splitting constants measured do not change over the 50-K temperature interval studied.

  18. Morphologically Aligned Cation-Exchange Membranes by a Pulsed Electric Field for Reverse Electrodialysis.

    PubMed

    Lee, Ju-Young; Kim, Jae-Hun; Lee, Ju-Hyuk; Kim, Seok; Moon, Seung-Hyeon

    2015-07-21

    A low-resistance ion-exchange membrane is essential to achieve the high-performance energy conversion or storage systems. The formation methods for low-resistance membranes are various; one of the methods is the ion channel alignment of an ion-exchange membrane under a direct current (DC) electric field. In this study, we suggest a more effective alignment method than the process with the DC electric field. First, an ion-exchange membrane was prepared under a pulsed electric field [alternating current (AC) mode] to enhance the effectiveness of the alignment. The membrane properties and the performance in reverse electrodialysis (RED) were then examined to assess the membrane resistance and ion selectivity. The results show that the membrane electrical resistance (MER) had a lower value of 0.86 Ω cm(2) for the AC membrane than 2.13 Ω cm(2) observed for the DC membrane and 4.30 Ω cm(2) observed for the pristine membrane. Furthermore, RED achieved 1.34 W/m(2) of maximum power density for the AC membrane, whereas that for the DC membrane was found to be 1.14 W/m(2) [a RED stack assembled with CMX, used as a commercial cation-exchange membrane (CEM), showed 1.07 W/m(2)]. Thereby, the novel preparation process for a remarkable low-resistance membrane with high ion selectivity was demonstrated.

  19. New cation-exchange material based on a sulfonated 3,4-ethylenedioxythiophene monomer

    NASA Astrophysics Data System (ADS)

    Stéphan, O.; Schottland, P.; Le Gall, P.-Y.; Chevrot, C.

    1998-06-01

    The electrochemical oxidation, in aqueous medium, of a 3,4-ethylenedioxythiophene monomer functionalized by a sulfonate group exhibiting cation-exchange properties, allows the synthesis of a new type of water-soluble material. In order to synthesize in water, by oxidative electropolymerization, polymer films of controlled thickness containing attached sulfonate groups, we have investigated the polymerization of the functionalized monomer in the presence of the unsubstituted one without supporting electrolyte. Using an equimolar mixture (0.01 mol/l) of both monomers, copolymers exhibiting cation exchange abilities have been synthesized. As an example, th easy incorporation of hexaamine-ruthenium(III) into one of these copolymers is briefly reported. L'oxydation électrochimique en milieu aqueux d'un monomère de type 3,4- éthylènedioxythiophène fonctionnalisé par un groupement sulfonate permet d'envisager la synthèse d'un nouveau type de polymère hydrosoluble. Afin d'obtenir électrochimiquement en milieu aqueux, un film de polymère d'épaisseur contrôlée contenant des groupements sulfonates, nous avons evisagé de polymériser ce monomère en présence de son homologue non substitué. En partant d'un mélange équimolaire (0.01 mol/l) des deux monomères et en l'absence d'électrolyte support, nous avons synthétisé un matériau possédant des propriétés d'échange de cations. A titre d'exemple, nous présentons brièvement l'incorporation d'un complexe hexaaminé du ruthénium(III) dans un de ces copolymères.

  20. Solubility and Cation Exchange Properties of Synthetic Hydroxyapatite and Clinoptilolite Mixtures

    NASA Technical Reports Server (NTRS)

    Beiersdorfer, Raymond E.; Ming, Douglas W.

    2003-01-01

    A zeoponic plant growth system is defined as the cultivation of plants in artificial soils, which have zeolites as a major component. These systems: 1) can serve as a controllable and renewable fertilization system to provide plant growth nutrients; 2) can mitigate the adverse effects of contamination due to leaching of highly soluble and concentrated fertilizers; and 3) are being considered as substrates for plant growth in regenerative life-support systems for long-duration space missions. Batch-equilibrium studies of the dissolution and ion-exchange properties of mixtures of naturally-occurring Wyoming clinoptilolite (a zeolite) exchanged with K(+) or NH4(+); and synthetic hydroxyapatite were conducted to determine: 1) the plant availability of the macro-nutrients NH4-N, P, K, Ca, and Mg and 2) the effects of varying the clinoptilolite to hydroxyapatite ratio and the ratio of exchangeable cations (K(+) vs. NH4(+)) on clinoptilolite extraframework sites. The nutrients NH4-N (19.7 to 73.6 mg L(sup -1), P (0.57 to 14.99 mg L(sup- 1), K (14.8 to 104.9 mg L(sup -1), and Mg (0.11 to 6.68mg L(sup -1) are available to plants at sufficient levels. Solution Ca concentrations (0.47 to 3.40 mg L(sup -1) are less than optimal. Solution concentrations of NH4(+), K(+), Ca(2+), and Mg(2+) all decreased with increasing clinoptilolite to hydroxyapatite ratio in the sample. Solution concentrations of phosphorous initially increased, reached a maximum value and then decreased with increasing clinoptilolite to hydroxyapatite ratio in the sample. The NH4(+) -exchanged clinoptilolite is more efficient in dissolving synthetic hydroxyapatite than the K(+) -exchanged clinoptilolite. This suggests that NH4(+), which is less selective at clinoptilolite extraframework sites than K(+) is exchanged more readily by Ca(2+) and thereby enhances the dissolution of the synthetic hydroxyapatite.

  1. Cu₂Se and Cu Nanocrystals as Local Sources of Copper in Thermally Activated In Situ Cation Exchange.

    PubMed

    Casu, Alberto; Genovese, Alessandro; Manna, Liberato; Longo, Paolo; Buha, Joka; Botton, Gianluigi A; Lazar, Sorin; Kahaly, Mousumi Upadhyay; Schwingenschloegl, Udo; Prato, Mirko; Li, Hongbo; Ghosh, Sandeep; Palazon, Francisco; De Donato, Francesco; Mozo, Sergio Lentijo; Zuddas, Efisio; Falqui, Andrea

    2016-02-23

    Among the different synthesis approaches to colloidal nanocrystals, a recently developed toolkit is represented by cation exchange reactions, where the use of template nanocrystals gives access to materials that would be hardly attainable via direct synthesis. Besides, postsynthetic treatments, such as thermally activated solid-state reactions, represent a further flourishing route to promote finely controlled cation exchange. Here, we report that, upon in situ heating in a transmission electron microscope, Cu2Se or Cu nanocrystals deposited on an amorphous solid substrate undergo partial loss of Cu atoms, which are then engaged in local cation exchange reactions with Cu "acceptor" phases represented by rod- and wire-shaped CdSe nanocrystals. This thermal treatment slowly transforms the initial CdSe nanocrystals into Cu(2-x)Se nanocrystals, through the complete sublimation of Cd and the partial sublimation of Se atoms. Both Cu "donor" and "acceptor" particles were not always in direct contact with each other; hence, the gradual transfer of Cu species from Cu2Se or metallic Cu to CdSe nanocrystals was mediated by the substrate and depended on the distance between the donor and acceptor nanostructures. Differently from what happens in the comparably faster cation exchange reactions performed in liquid solution, this study shows that slow cation exchange reactions can be performed at the solid state and helps to shed light on the intermediate steps involved in such reactions. PMID:26816347

  2. Cu2Se and Cu Nanocrystals as Local Sources of Copper in Thermally Activated In Situ Cation Exchange

    PubMed Central

    2016-01-01

    Among the different synthesis approaches to colloidal nanocrystals, a recently developed toolkit is represented by cation exchange reactions, where the use of template nanocrystals gives access to materials that would be hardly attainable via direct synthesis. Besides, postsynthetic treatments, such as thermally activated solid-state reactions, represent a further flourishing route to promote finely controlled cation exchange. Here, we report that, upon in situ heating in a transmission electron microscope, Cu2Se or Cu nanocrystals deposited on an amorphous solid substrate undergo partial loss of Cu atoms, which are then engaged in local cation exchange reactions with Cu “acceptor” phases represented by rod- and wire-shaped CdSe nanocrystals. This thermal treatment slowly transforms the initial CdSe nanocrystals into Cu2–xSe nanocrystals, through the complete sublimation of Cd and the partial sublimation of Se atoms. Both Cu “donor” and “acceptor” particles were not always in direct contact with each other; hence, the gradual transfer of Cu species from Cu2Se or metallic Cu to CdSe nanocrystals was mediated by the substrate and depended on the distance between the donor and acceptor nanostructures. Differently from what happens in the comparably faster cation exchange reactions performed in liquid solution, this study shows that slow cation exchange reactions can be performed at the solid state and helps to shed light on the intermediate steps involved in such reactions. PMID:26816347

  3. Separation of -amino acids using a series of zwitterionic sulfobetaine exchangers.

    PubMed

    Sonnenschein, Lukas; Seubert, Andreas

    2011-09-01

    A set of five new covalently bond sulfobetaine exchangers with inner quaternary amines and outer sulfonic acids have been prepared by attachment of a series of zwitterionic precursors to hyperporous divinylbenzene polymers using a grafting reaction. The series of zwitterionic exchangers have the same backbone and identical spacers to the polymeric backbone, as well as comparable capacities. The only difference is the chain length for one to five methylene groups between the charged functional groups. Chromatographic properties are examined by separation of α-amino acids using sodium acetate and nitric acid eluents. The separation mechanism is explored by varying eluent ionic strength and eluent pH, resulting in the conclusion that amino acids are separated due to cation exchange interactions. This is a behavior never before observed using zwitterionic exchangers. It contradicts the fact that sulfobetaine-type materials used in zwitterionic ion chromatography (ZIC) usually are well suited for anion separation and only poorly for cation separation. Contrary to anion separations using the identical set of exchangers, the materials with three and four methylene groups between the charges give the highest retention factors. Materials showing the high potential in ZIC separations of inorganic anions give low retention factors for amino acids and vice versa. PMID:21859531

  4. Advance chromatin extraction enhances performance and productivity of cation exchange chromatography-based capture of Immunoglobulin G monoclonal antibodies.

    PubMed

    Nian, Rui; Gagnon, Pete

    2016-07-01

    The impact of host cell-derived chromatin was investigated on the performance and productivity of cation exchange chromatography as a method for capture-purification of an IgG monoclonal antibody. Cell culture supernatant was prepared for loading by titration to pH 6.0, dilution with water to a conductivity of 4mS/cm, then microfiltration to remove solids. DNA content was reduced 99% to 30ppm, histone host cell protein content by 76% to 6300ppm, non-histone host cell protein content by 15% to 321,000ppm, and aggregates from 33% to 15%. IgG recovery was 83%. An alternative preparation was performed, adding octanoic acid, allantoin, and electropositive particles to the harvest at pH 5.3, then removing solids. DNA content was reduced to<1 ppb, histones became undetectable, non-histones were reduced to 24,000ppm, and aggregates were reduced to 2.4%. IgG recovery was 95%. This treatment increased dynamic capacity (DBC) of cation exchange capture to 173g/L and enabled the column to reduce non-histone host proteins to 671ppm. Step recovery was 99%. A single multimodal polishing step further reduced them to 15ppm and aggregates to <0.1%. Overall process recovery was 89%. Productivity at feed stream IgG concentrations of 5-10g/L was roughly double the productivity of a same-size protein A column with a DBC of 55g/L. PMID:27247214

  5. Permethyl Cobaltocenium (Cp*2Co+) as an Ultra-Stable Cation for Polymer Hydroxide-Exchange Membranes

    NASA Astrophysics Data System (ADS)

    Gu, Shuang; Wang, Junhua; Kaspar, Robert B.; Fang, Qianrong; Zhang, Bingzi; Bryan Coughlin, E.; Yan, Yushan

    2015-06-01

    Hydroxide (OH-)-exchange membranes (HEMs) are important polymer electrolytes enabling the use of affordable and earth-abundant electrocatalysts for electrochemical energy-conversion devices such as HEM fuel cells, HEM electrolyzers, and HEM solar hydrogen generators. Many HEM cations exist, featuring desirable properties, but new cations are still needed to increase chemical stability at elevated temperatures. Here we introduce the permethyl cobaltocenium [(C5Me5)2Co(III)+ or Cp*2Co+] as an ultra-stable organic cation for polymer HEMs. Compared with the parent cobaltocenium [(C5H5)2Co(III)+ or Cp2Co+], Cp*2Co+ has substantially higher stability and basicity. With polysulfone as an example, we demonstrated the feasibility of covalently linking Cp*2Co+ cation to polymer backbone and prepared Cp*2Co+-functionalized membranes as well. The new cation may be useful in designing more durable HEM electrochemical devices.

  6. Permethyl Cobaltocenium (Cp*2Co+) as an Ultra-Stable Cation for Polymer Hydroxide-Exchange Membranes.

    PubMed

    Gu, Shuang; Wang, Junhua; Kaspar, Robert B; Fang, Qianrong; Zhang, Bingzi; Bryan Coughlin, E; Yan, Yushan

    2015-06-29

    Hydroxide (OH(-))-exchange membranes (HEMs) are important polymer electrolytes enabling the use of affordable and earth-abundant electrocatalysts for electrochemical energy-conversion devices such as HEM fuel cells, HEM electrolyzers, and HEM solar hydrogen generators. Many HEM cations exist, featuring desirable properties, but new cations are still needed to increase chemical stability at elevated temperatures. Here we introduce the permethyl cobaltocenium [(C5Me5)2Co(III)(+) or Cp(*)2Co(+)] as an ultra-stable organic cation for polymer HEMs. Compared with the parent cobaltocenium [(C5H5)2Co(III)(+) or Cp2Co(+)], Cp(*)2Co(+) has substantially higher stability and basicity. With polysulfone as an example, we demonstrated the feasibility of covalently linking Cp(*)2Co(+) cation to polymer backbone and prepared Cp(*)2Co(+)-functionalized membranes as well. The new cation may be useful in designing more durable HEM electrochemical devices.

  7. Permethyl Cobaltocenium (Cp*2Co+) as an Ultra-Stable Cation for Polymer Hydroxide-Exchange Membranes

    PubMed Central

    Gu, Shuang; Wang, Junhua; Kaspar, Robert B.; Fang, Qianrong; Zhang, Bingzi; Bryan Coughlin, E.; Yan, Yushan

    2015-01-01

    Hydroxide (OH−)-exchange membranes (HEMs) are important polymer electrolytes enabling the use of affordable and earth-abundant electrocatalysts for electrochemical energy-conversion devices such as HEM fuel cells, HEM electrolyzers, and HEM solar hydrogen generators. Many HEM cations exist, featuring desirable properties, but new cations are still needed to increase chemical stability at elevated temperatures. Here we introduce the permethyl cobaltocenium [(C5Me5)2Co(III)+ or Cp*2Co+] as an ultra-stable organic cation for polymer HEMs. Compared with the parent cobaltocenium [(C5H5)2Co(III)+ or Cp2Co+], Cp*2Co+ has substantially higher stability and basicity. With polysulfone as an example, we demonstrated the feasibility of covalently linking Cp*2Co+ cation to polymer backbone and prepared Cp*2Co+-functionalized membranes as well. The new cation may be useful in designing more durable HEM electrochemical devices. PMID:26119573

  8. Adsorptional removal of methylene blue by guar gum-cerium (IV) tungstate hybrid cationic exchanger.

    PubMed

    Gupta, V K; Pathania, Deepak; Singh, Pardeep; Kumar, Amit; Rathore, B S

    2014-01-30

    Guar gum-cerium (IV) tungstate nanocomposite (GG/CTNC) cationic exchanger was synthesized using simple sol gel method. The GG/CTNC was characterized using X-ray diffraction (XRD), Fourier transmission infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and energy dispersive X-ray spectrophotometer (EDX). The XRD studies confirmed amorphous and fibrous in nature of GG/CTNC. The high percentage of oxygen in the nanocomposite material confirmed the functionality tungstate (WO4(-)). The ion exchange capacity of GG/CTNC for Na(+) ion was observed to be 1.30 mequivg(-1). The hybrid exchanger was used as potential adsorbent for the removal of methylene blue (MB) from aqueous system. The correlation coefficients value indicated a good fit of monolayer Langmuir model to the adsorption of methylene blue onto GG/CTNC. The adsorption kinetic study revealed that the adsorption process followed the pseudo second order kinetic. The Gibbs free energy (ΔG) values confirmed the spontaneous nature of adsorption process.

  9. Independent control of the shape and composition of ionic nanocrystals through sequential cation exchange reactions

    SciTech Connect

    Luther, Joseph Matthew; Zheng, Haimei; Sadtler, Bryce; Alivisatos, A. Paul

    2009-07-06

    Size- and shape-controlled nanocrystal growth is intensely researched for applications including electro-optic, catalytic, and medical devices. Chemical transformations such as cation exchange overcome the limitation of traditional colloidal synthesis, where the nanocrystal shape often reflects the inherent symmetry of the underlying lattice. Here we show that nanocrystals, with established synthetic protocols for high monodispersity, can be templates for independent composition control. Specifically, controlled interconversion between wurtzite CdS, chalcocite Cu2S, and rock salt PbS occurs while preserving the anisotropic dimensions unique to the as-synthesized materials. Sequential exchange reactions between the three sulfide compositions are driven by the disparate solubilites of the metal ion exchange pair in specific coordinating molecules. Starting with CdS, highly anisotropic PbS nanorods are created, which serve as an important material for studying strong 2-dimensional quantum confinement, as well as for optoelectronic applications. Furthermore, interesting nanoheterostructures of CdS|PbS are obtained by precise control over ion insertion and removal.

  10. Characterization of perfluorinated cation-exchange membranes MF-4SC surface modified with halloysite nanotubes

    NASA Astrophysics Data System (ADS)

    Filippov, A.; Afonin, D.; Kononenko, N.; Shkirskaya, S.

    2015-10-01

    The electrical conductivity and diffusion permeability through perfluorinated cation-exchange membranes MF-4SC (Russian analog of the Nafion-type membrane), whose surface is modified by nanotubes of halloysite using short exposures of low temperature microwave plasma, are theoretically investigated using the Nernst-Planck approach. The method of quantitative evaluation of physicochemical parameters (individual and averaged diffusion coefficients and averaged distribution coefficients of ion pairs in the membrane) of the systems `electrolyte solution - bi-layer ion-exchange membrane - water/electrolyte solution', which was proposed by us earlier, is further developed. The aforementioned parameters of modified MF-4SC/halloysite membranes were found using the least squares method. For this purpose we used electrical conductivity as well as diffusion permeability data experimentally obtained for NaCl and HCl solutions of different concentration. A new model of bi-layer membrane system can be used for refining the calculated results by taking into account the difference between co- and counter-ion diffusivities inside the membrane layers. We showed that grafting the layer of halloysite nanotubes onto the membrane surface noticeably affects the exchange capacity as well as the structural and transport characteristics of the original perfluorinated membrane. In particular, such a membrane may show weak asymmetry of diffusion permeability when its position inside a measuring cell is changed. Hybrid MF-4SC/halloysite membranes can thus be productively used in fuel cells and catalysis.

  11. ADSORPTION METHOD FOR SEPARATING METAL CATIONS

    DOEpatents

    Khym, J.X.

    1959-03-10

    The chromatographic separation of fission product cations is discussed. By use of this method a mixture of metal cations containing Zr, Cb, Ce, Y, Ba, and Sr may be separated from one another. Mentioned as preferred exchange adsorbents are resins containing free sulfonic acid groups. Various eluants, such as tartaric acid, HCl, and citric acid, used at various acidities, are employed to effect the selective elution and separation of the various fission product cations.

  12. Combined Utilization of Cation Exchanger and Neutral Receptor to Volume Reduction of Alkaline Tank Waste by Separation of Sodium Salts

    SciTech Connect

    Levitskaia, Tatiana G.; Lumetta, Gregg J.; Moyer, Bruce A.

    2004-03-29

    In this report, novel approaches to the selective liquid-liquid extraction separation of sodium hydroxide and sodium nitrate from high-level alkaline tank waste will be discussed. Sodium hydroxide can be successfully separated from alkaline tank-waste supernatants by weakly acidic lipophilic hydroxy compounds via a cation-exchange mechanism referred to as pseudo hydroxide extraction. In a multi-cycle process, as sodium hydroxide in the aqueous phase becomes depleted, it is helpful to have a neutral sodium receptor in the extraction system to exploit the high nitrate concentration in the waste solution to promote sodium removal by an ion-pair extraction process. Simultaneous utilization of an ionizable organic hydroxy compound and a neutral extractant (crown ether) in an organic phase results in the synergistic enhancement of ion exchange and improved separation selectivity due to the receptor's strong and selective sodium binding. Moreover, combination of the hydroxy compound and the crown ether provides for mutually increased solubility, even in a non-polar organic solvent. Accordingly, application of Isopar{reg_sign} L, a kerosene-like alkane solvent, becomes feasible. This investigation involves examination of such dual-mechanism extraction phases for sodium extraction from simulated and actual salt cake waste solutions. Sodium salts can be regenerated upon the contact of the loaded extraction phases with water. Finally, conditions of potential extraction/strip cycling will be discussed.

  13. Use of a new tandem cation/anion exchange system with clinical-scale generators provides high specific volume solutions of technetium-99m and rhenium-188

    SciTech Connect

    Knapp, F.R. Jr.; Beets, A.L.; Mirzadeh, S.; Guhlke, S. |

    1998-03-01

    In this paper the authors describe the first application of a simple and inexpensive post elution tandem cation-anion exchange column system which is based on generator elution with salts of weak acids such as ammonium acetate instead of saline solution to provide very high specific volume solutions of technetium-99m and rhenium-188 from clinical scale molybdenum-99/technetium-99m generator prepared from low specific activity (n,y) molybdenum-99, and tungsten-188/rhenium-188 generators, respectively. Initial passage of the bolus through a strong cation exchange cartridge converts the ammonium acetate to acetic acid which is essentially not ionized at the acidic pH, allowing specific subsequent amine type (QMA SepPak{trademark}) anion exchange cartridge column trapping of the microscopic levels of the pertechnetate or perrhenate. Subsequent elution of the anion cartridge with a small volume (< 1 mL) of saline then provides high specific volume solutions of technetium-99m by concentration of the high eluant volumes obtained by elution of clinical-scale (1 Ci) generators. This new approach also works very effectively to obtain high specific volume solutions of rhenium-188 (> 500 mCi/mL) from the alumina-based tungsten-188/rhenium-188 generator.

  14. Amino acids, precursors for cationic and anionic intercalation synthesis and characterization of amino acid pillared materials

    NASA Astrophysics Data System (ADS)

    Fudala, Á.; Pálinkó, I.; Kiricsi, I.

    1999-05-01

    The preparation and characterization of amino acid pillared materials are reported in this contribution. Host substances were Na-montmorillonite for cationic and hydrotalcite for anionic pillaring. Guest molecules were L-phenylalanine and L-tyrosine. The pillared materials were characterized by powder X-ray diffraction, BET measurements and FT-IR spectroscopy. Pillaring was successful: the layers propped open and the basal distances increased significantly. For hydrotalcite this increase was always significantly larger than for montmorillonite. This fact indicated that the spatial arrangement of the amino acid moieties is widely different. A model for this arrangement is given.

  15. Cobalt determination in natural waters using cation-exchange liquid chromatography with luminol chemiluminescence detection

    SciTech Connect

    Boyle, E.A.; Handy, B.; van Geen, A.

    1987-06-01

    A method has been developed for the analysis of cobalt in natural waters by cation-exchange liquid chromatography using chemiluminescence detection. Cobalt can be determined directly in freshwater samples on 500-..mu..L samples with a detection limit of 20 pmol/kg; larger samples provide proportionately lower detection limits. Seawater samples can be analyzed on 100-mL samples following APDC solvent extraction; the detection limit of this method is 5 pmol/kg. The precision of the method is +/- 5%. The method should also be applicable to the analysis of V, Cu, and Fe in natural waters. Equipment is low in cost and transportable and can be used in the field.

  16. Chromatographic cation exchange separation of decigram quantities of californium and other transplutonium elements

    SciTech Connect

    Benker, D.E.; Chattin, F.R.; Collins, E.D.; Knauer, J.B.; Orr, P.B.; Ross, R.G.; Wiggins, J.T.

    1980-01-01

    Decigram quantities of highly radioactive transplutonium elements are routinely partitioned at TRU by chromatographic elution from cation resin using AHIB eluent. By using two high-pressure ion exchange columns, a small one for the initial loading of the feed and a large one for the elution, batch runs containing up to 200 mg of /sup 252/Cf can be made in about 5 hours (2 hours to load the feed and 3 hours for the elution). The number of effluent product fractions and the amount of actinides that must be collected in intermediate fractions are minimized by monitoring response from a flow-through alpha-detector. This process has been reliable and relatively easy to operate, and will continue to be used for partitioning transplutonium elements at TRU.

  17. A New Cation-Exchange Method for Accurate Field Speciation of Hexavalent Chromium

    USGS Publications Warehouse

    Ball, James W.; McCleskey, R. Blaine

    2003-01-01

    A new cation-exchange method for field speciation of Cr(VI) has been developed to meet present stringent regulatory standards and to overcome the limitations of existing methods. The new method allows measurement of Cr(VI) concentrations as low as 0.05 micrograms per liter, storage of samples for at least several weeks prior to analysis, and use of readily available analytical instrumentation. The sensitivity, accuracy, and precision of the determination in waters over the pH range of 2 to 11 and Fe concentrations up to 1 milligram per liter are equal to or better than existing methods such as USEPA method 218.6. Time stability of preserved samples is a significant advantage over the 24-hour time constraint specified for USEPA method 218.6.

  18. Electrochemical catalytic treatment of wastewater by metal ion supported on cation exchange resin.

    PubMed

    Wang, Ying; Wang, Bo; Ma, Hongzhu

    2006-10-11

    The electrochemical oxidation of phenol in synthetic wastewater and paper mill wastewater catalyzed by metal ion supported on cation exchange resin in suspended bed electrolytic reactor with graphite electrode has been investigated. The catalyst was characterized by SEM and XPS spectra and the effects of pH, the different metal ion and NaCl on the efficiency of the electrochemical oxidation phenol process were also studied. It was found that the catalyst containing Fe(3+) had the highest electrochemical catalytic activity for the electrochemical oxidation of phenol. When the initial concentration of phenol was 200 ppm, up to 90% chemical oxygen demand (COD) removal was obtained in 10 min. When the catalyst containing Fe(3+) was used to the paper mill wastewater, it still showed high efficiency. The COD removal could get to 75% in 60 min.

  19. Phase-selective cation-exchange chemistry in sulfide nanowire systems.

    PubMed

    Zhang, Dandan; Wong, Andrew B; Yu, Yi; Brittman, Sarah; Sun, Jianwei; Fu, Anthony; Beberwyck, Brandon; Alivisatos, A Paul; Yang, Peidong

    2014-12-17

    As a cation-deficient, p-type semiconductor, copper sulfide (Cu(2-x)S) shows promise for applications such as photovoltaics, memristors, and plasmonics. However, these applications demand precise tuning of the crystal phase as well as the stoichiometry of Cu(2-x)S, an ongoing challenge in the synthesis of Cu(2-x)S materials for a specific application. Here, a detailed transformation diagram of cation-exchange (CE) chemistry from cadmium sulfide (CdS) into Cu(2-x)S nanowires (NWs) is reported. By varying the reaction time and the reactants' concentration ratio, the progression of the CE process was captured, and tunable crystal phases of the Cu(2-x)S were achieved. It is proposed that the evolution of Cu(2-x)S phases in a NW system is dependent on both kinetic and thermodynamic factors. The reported data demonstrate that CE can be used to precisely control the structure, composition, and crystal phases of NWs, and such control may be generalized to other material systems for a variety of practical applications.

  20. Ion-exchange and selectivity behavior of thermally treated and. gamma. -irradiated phases of zirconium(IV) arsenophosphate cation exchanger: separation of Al(III) from some metal ions and removal of cations from water

    SciTech Connect

    Varshney, K.G.; Varshney, K.; Agrawal, S.

    1983-01-01

    Ion-exchange and selectivity behavior of zirconium(IV) arsenophosphate (ZAP) has been studied systematically after thermal and irradiation treatments. As a result, an increase in the ion-exchange capacity and a complete reversal in the selectivity sequence for some common metal ions has been observed on heating. The modified phase of ZAP has been utilized successfully for the quantitative separation of aluminum from numerous metal ions and for the removal of cations from water. 5 figures, 3 tables.

  1. Enhanced Cd2+ -selective root-tonoplast-transport in tobaccos expressing Arabidopsis cation exchangers.

    PubMed

    Koren'kov, V; Park, S; Cheng, N-H; Sreevidya, C; Lachmansingh, J; Morris, J; Hirschi, K; Wagner, G J

    2007-01-01

    Several Arabidopsis CAtion eXchangers (CAXs) encode tonoplast-localized transporters that appear to be major contributors to vacuolar accumulation/sequestration of cadmium (Cd(2+)), an undesirable pollutant ion that occurs in man largely as a result of dietary consumption of aerial tissues of food plants. But, ion-selectivity of individual CAX transporter types remains largely unknown. Here, we transformed Nicotiana tabacum with several CAX genes driven by the Cauliflower Mosaic Virus (CaMV) 35S promoter and monitored divalent cation transport in root-tonoplast vesicles from these plants in order to select particular CAX genes directing high Cd(2+) antiporter activity in root tonoplast. Comparison of seven different CAX genes indicated that all transported Cd(2+), Ca(2+), Zn(2+), and Mn(2+) to varying degrees, but that CAX4 and CAX2 had high Cd(2+) transport and selectivity in tonoplast vesicles. CAX4 driven by the CaMV 35S and FS3 [figwort mosaic virus (FMV)] promoters increased the magnitude and initial rate of Cd(2+)/H(+) exchange in root-tonoplast vesicles. Ion selectivity of transport in root-tonoplast vesicles isolated from FS3::CAX4-expressing plant lines having a range of gene expression was Cd(2+)>Zn(2+)>Ca(2+)>Mn(2+) and the ratios of maximal Cd(2+) (and Zn(2+)) versus maximal Ca(2+) and Mn(2+) transport were correlated with the levels of CAX4 expression. Root Cd accumulation in high CAX4 and CAX2 expressing lines was increased in seedlings grown with 0.02 muM Cd. These observations are consistent with a model in which expression of an Arabidopsis-gene-encoded, Cd(2+)-efficient antiporter in host plant roots results in greater root vacuole Cd(2+) transport activity, increased root Cd accumulation, and a shift in overall root tonoplast ion transport selectivity towards higher Cd(2+) selectivity. Results support a model in which certain CAX antiporters are somewhat more selective for particular divalent cations.

  2. Quantification of unsaturated-zone alteration and cation exchange in zeolitized tuffs at Yucca Mountain, Nevada, USA

    NASA Astrophysics Data System (ADS)

    Vaniman, David T.; Chipera, Steve J.; Bish, David L.; Carey, J. William; Levy, Schön S.

    2001-10-01

    Zeolitized horizons in the unsaturated zone (UZ) at Yucca Mountain, Nevada, USA, are an important component in concepts for a high-level nuclear waste repository at this site. The use of combined quantitative X-ray diffraction and geochemical analysis allows measurement of the chemical changes that accompanied open-system zeolitization at Yucca Mountain. This approach also provides measures of the extent of chemical migration that has occurred in these horizons as a result of subsequent cation exchange. Mass-balance analysis of zeolitized horizons with extensive cation exchange (drill hole UZ-16) and with only minimal cation exchange (drill hole SD-9) shows that Al is essentially immobile. Although zeolitization occurred in an open system, the mass transfer of constituents other than water is relatively small in initial zeolitization, in contrast to the larger scales of cation exchange that can occur after zeolites have formed. Cation exchange in the clinoptilolite ± mordenite zeolitized horizons is seen in downward-diminishing concentration gradients of Ca, Mg, and Sr exchanged for Na and (to lesser extent) K. Comparison with data from drill hole SD-7, which has multiple zeolitized horizons above the water table, shows that the upper horizons accumulate Ca, Mg, and Sr to such an extent that transport of these elements to the deepest UZ zeolitized horizon can be blocked. Quantitative analysis of zeolite formation yields insight into processes that are implied from laboratory studies and modeling efforts but are otherwise unverified at the site. Such analysis also yields information not provided by or contradicted by some models of flow and transport. The results include the following: (1) evidence of effective downward flow through zeolitic horizons despite the low permeability of these horizons, (2) evidence that alkaline-earth elements accumulated by zeolites are mostly derived from eolian materials in surface soils, (3) validation of the very effective

  3. Sorption of chlorophenols on microporous minerals: mechanism and influence of metal cations, solution pH, and humic acid.

    PubMed

    Yang, Hui; Hu, Yuanan; Cheng, Hefa

    2016-10-01

    Sorption of 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), and 2,4,6-trichlorophenol (2,4,6-TCP) on a range of dealuminated zeolites were investigated to understand the mechanism of their sorption on microporous minerals, while the influence of common metal cations, solution pH, and humic acid was also studied. Sorption of chlorophenols was found to increase with the hydrophobicity of the sorbates and that of the microporous minerals, indicating the important role of hydrophobic interactions, while sorption was also stronger in the micropores of narrower sizes because of greater enhancement of the dispersion interactions. The presence of metal cations could enhance chlorophenol sorption due to the additional electrostatic attraction between metal cations exchanged into the mineral micropores and the chlorophenolates, and this effect was apparent on the mineral sorbent with a high density of surface cations (2.62 sites/nm(2)) in its micropores. Under circum-neutral or acidic conditions, neutral chlorophenol molecules adsorbed into the hydrophobic micropores through displacing the "loosely bound" water molecules, while their sorption was negligible under moderately alkaline conditions due to electrostatic repulsion between the negatively charged zeolite framework and anionic chlorophenolates. The influence of humic acid on sorption of chlorophenols on dealuminated Y zeolites suggests that its molecules did not block the micropores but created a secondary sorption sites by forming a "coating layer" on the external surface of the zeolites. These mechanistic insights could help better understand the interactions of ionizable chlorophenols and metal cations in mineral micropores and guide the selection and design of reusable microporous mineral sorbents for sorptive removal of chlorophenols from aqueous stream. PMID:27364487

  4. Sorption of chlorophenols on microporous minerals: mechanism and influence of metal cations, solution pH, and humic acid.

    PubMed

    Yang, Hui; Hu, Yuanan; Cheng, Hefa

    2016-10-01

    Sorption of 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), and 2,4,6-trichlorophenol (2,4,6-TCP) on a range of dealuminated zeolites were investigated to understand the mechanism of their sorption on microporous minerals, while the influence of common metal cations, solution pH, and humic acid was also studied. Sorption of chlorophenols was found to increase with the hydrophobicity of the sorbates and that of the microporous minerals, indicating the important role of hydrophobic interactions, while sorption was also stronger in the micropores of narrower sizes because of greater enhancement of the dispersion interactions. The presence of metal cations could enhance chlorophenol sorption due to the additional electrostatic attraction between metal cations exchanged into the mineral micropores and the chlorophenolates, and this effect was apparent on the mineral sorbent with a high density of surface cations (2.62 sites/nm(2)) in its micropores. Under circum-neutral or acidic conditions, neutral chlorophenol molecules adsorbed into the hydrophobic micropores through displacing the "loosely bound" water molecules, while their sorption was negligible under moderately alkaline conditions due to electrostatic repulsion between the negatively charged zeolite framework and anionic chlorophenolates. The influence of humic acid on sorption of chlorophenols on dealuminated Y zeolites suggests that its molecules did not block the micropores but created a secondary sorption sites by forming a "coating layer" on the external surface of the zeolites. These mechanistic insights could help better understand the interactions of ionizable chlorophenols and metal cations in mineral micropores and guide the selection and design of reusable microporous mineral sorbents for sorptive removal of chlorophenols from aqueous stream.

  5. Estimating Soil Cation Exchange Capacity from Soil Physical and Chemical Properties

    NASA Astrophysics Data System (ADS)

    Bateni, S. M.; Emamgholizadeh, S.; Shahsavani, D.

    2014-12-01

    The soil Cation Exchange Capacity (CEC) is an important soil characteristic that has many applications in soil science and environmental studies. For example, CEC influences soil fertility by controlling the exchange of ions in the soil. Measurement of CEC is costly and difficult. Consequently, several studies attempted to obtain CEC from readily measurable soil physical and chemical properties such as soil pH, organic matter, soil texture, bulk density, and particle size distribution. These studies have often used multiple regression or artificial neural network models. Regression-based models cannot capture the intricate relationship between CEC and soil physical and chemical attributes and provide inaccurate CEC estimates. Although neural network models perform better than regression methods, they act like a black-box and cannot generate an explicit expression for retrieval of CEC from soil properties. In a departure with regression and neural network models, this study uses Genetic Expression Programming (GEP) and Multivariate Adaptive Regression Splines (MARS) to estimate CEC from easily measurable soil variables such as clay, pH, and OM. CEC estimates from GEP and MARS are compared with measurements at two field sites in Iran. Results show that GEP and MARS can estimate CEC accurately. Also, the MARS model performs slightly better than GEP. Finally, a sensitivity test indicates that organic matter and pH have respectively the least and the most significant impact on CEC.

  6. Simultaneous Isolation of Lactoferrin and Lactoperoxidase from Bovine Colostrum by SPEC 70 SLS Cation Exchange Resin

    PubMed Central

    Liang, Yafei; Wang, Xuewan; Wu, Mianbin; Zhu, Wanping

    2011-01-01

    In this work, simultaneous isolation of lactoferrin (Lf) and lactoperoxidase (Lp) from defatted bovine colostrum by one-step cation exchange chromatography with SPEC 70 SLS ion-exchange resin was investigated. A RP-HPLC method for Lf and Lp determination was developed and optimized as the following conditions: detection wavelength of 220 nm, flow rate of 1 mL/min and acetonitrile concentration from 25% to 75% within 20 min. The adsorption process of Lf on SPEC 70 SLS resin was optimized using Lf standard as substrate. The maximum static binding capacity of SPEC 70 SLS resin was of 22.0 mg/g resin at 15 °C, pH 7.0 and adsorption time 3 h. The Lf adsorption process could be well described by the Langmuir adsorption isotherm model, with a maximum adsorption capacity of 21.73 mg/g resin at 15 °C. In batch fractionation of defatted colostrum, the binding capacities of SPEC 70 SLS resin for adsorbing Lf and Lp simultaneously under the abovementioned conditions were 7.60 and 6.89 mg/g resin, respectively, both of which were superior to those of CM Sepharose F.F. or SP Sepharose F.F. resins under the same conditions. As a result, SPEC 70 SLS resin was considered as a successful candidate for direct and economic purification of Lf and Lp from defatted colostrum. PMID:22016715

  7. Simultaneous isolation of lactoferrin and lactoperoxidase from bovine colostrum by SPEC 70 SLS cation exchange resin.

    PubMed

    Liang, Yafei; Wang, Xuewan; Wu, Mianbin; Zhu, Wanping

    2011-09-01

    In this work, simultaneous isolation of lactoferrin (Lf) and lactoperoxidase (Lp) from defatted bovine colostrum by one-step cation exchange chromatography with SPEC 70 SLS ion-exchange resin was investigated. A RP-HPLC method for Lf and Lp determination was developed and optimized as the following conditions: detection wavelength of 220 nm, flow rate of 1 mL/min and acetonitrile concentration from 25% to 75% within 20 min. The adsorption process of Lf on SPEC 70 SLS resin was optimized using Lf standard as substrate. The maximum static binding capacity of SPEC 70 SLS resin was of 22.0 mg/g resin at 15 °C, pH 7.0 and adsorption time 3 h. The Lf adsorption process could be well described by the Langmuir adsorption isotherm model, with a maximum adsorption capacity of 21.73 mg/g resin at 15 °C. In batch fractionation of defatted colostrum, the binding capacities of SPEC 70 SLS resin for adsorbing Lf and Lp simultaneously under the abovementioned conditions were 7.60 and 6.89 mg/g resin, respectively, both of which were superior to those of CM Sepharose F.F. or SP Sepharose F.F. resins under the same conditions. As a result, SPEC 70 SLS resin was considered as a successful candidate for direct and economic purification of Lf and Lp from defatted colostrum.

  8. Ion-exchange properties of strontium hydroxyapatite under acidic conditions

    SciTech Connect

    Sugiyama, Shigeru; Nishioka, Hitoshi; Moriga, Toshihiro; Hayashi, Hiromu; Moffat, J.B.

    1998-09-01

    The ion exchange of strontium hydroxyapatite (SrHAp) with Pb{sup 2+} has been investigated under acidic conditions at 293 K. The addition of various acids to the exchanging solution enhanced the exchange capacity in the order HCl > HBr > HF > HNO{sub 3} > no acid, corresponding to the formation of halogen apatites with the former three acids or hydrogen phosphate with HNO{sub 3}. Since the ion-exchange capacity of SrHAp under nonacidic conditions is higher than that of chlorapatite, the aforementioned observations can be attributed to the participation of the protons introduced by the acids.z

  9. Production of U{sub 3}O{sub 8} Using Macroporous Sulfonate Cation Exchange Resins in the Bead Form

    SciTech Connect

    Mosley, W.C.

    2001-08-16

    The use of cation exchange resin to product U{sub 3}O{sub 8} suitable for powder metallurgy fabrication of reactor fuel tubes with Al-U{sub 3}O{sub 8} cores is being investigated. This report presents the results of those studies.

  10. Synthesis of Mesostructured Copper Sulfide by Cation Exchange and Liquid Crystal Templating

    SciTech Connect

    Lubeck, C R; Doyle, F M; Gash, A E; Satcher, J H; Han, T Y

    2005-08-01

    describe for the first time, the successful synthesis of highly ordered, mesostructured Cu{sub x}S, by combining the templating of the supramolecular assemblies of non-ionic amphiphilic polymer method with the cation exchange method to transform mesostructured cadmium sulfide (CdS) into mesostructured copper sulfides (CuS, Cu{sub 2}S).

  11. Role of simulated acid rain on cations, phosphorus, and organic matter dynamics in Latosol.

    PubMed

    Ling, Da-Jiong; Zhang, Jia-En; Ouyang, Ying; Huang, Qian-chun

    2007-01-01

    Acid rain is a serious environmental problem in the world and is of a particular concern in southern China where most of the soils are acidic. This study investigated the dynamics of cations, phosphorus (P), and soil organic matter (SOM) in the Latosol (acidic red soil) from south China under the influences of simulated acid rain (SAR). Laboratory experiments were performed by leaching the soil columns with SAR at pH levels ranging from 2.5 to 7.0 over a 21-day experimental period. Results show that about 34, 46, 20, and 77% of the original exchangeable soil Ca(+2), Mg(+2), K(+), and Na(+), respectively, were leached out by the SAR at pH 2.5 after 21 days. Two distinct patterns of the available phosphorus (AP) concentrations were observed: one at pH< or =3.5 and the other at pH > or = 4.0. At pH< or =3.5, concentrations of the AP increased from the beginning of the experiments to day 5, then decreased from day 5 to 15, and finally increased from day 15 to the end of the experiments. At pH > or = 4.0, concentrations of the AP increased consecutively from the beginning of the experiments to day 10 and decreased from day 10 to the end of the experiments. Such a finding is useful for agricultural practices since soil P is one of the most important macronutrients for plant growth. In general, SOM content decreased with time as the Latosol was leached by the SAR at all pH levels. A maximum concentration of soil fulvic acid was found after 15 days of the experiments due to the degradation of the SOM. A multiple regression analysis showed that a very strong relationship was obtained between the soil AP and the other three parameters (i.e., pH, SOM, and sorption P).

  12. An anionic zeolite-like metal-organic framework (AZMOF) with a Moravia network for organic dye absorption through cation-exchange.

    PubMed

    Shen, Yu; Fan, Cong-Cong; Wei, Yu-Zhen; Du, Jie; Zhu, Hai-Bin; Zhao, Yue

    2016-07-01

    An anionic zeolite-like metal-organic framework (AZMOF) with a twisted partially augmented the net, known as the "Moravia" net, [(CH3)2NH2]6[Sr13(O)3()8(OH)2(H2O)16]·xS (, where S represents non-coordinated solvent molecules, and is the abbreviation of benzo-(1,2;3,4;5,6)-tris-(thiophene-2'-carboxylic acid)), has been solvothermally synthesized and characterized, which possesses an anionic framework and nano-sized sodalite cage. Through cation-exchange, is capable of uptaking large organic cationic dyes including Rhodamine B (RB), Basic Red 2 (BR2), Crystal Violet (CV) and Methylene Blue (MB), amongst which the adsorption capability for RB (up to 545 mg g(-1)), and BR2 (up to 675 mg g(-1)) is the highest for reported absorbants to date. PMID:27301344

  13. Bandgap tunable colloidal Cu-based ternary and quaternary chalcogenide nanosheets via partial cation exchange

    NASA Astrophysics Data System (ADS)

    Ramasamy, Parthiban; Kim, Miri; Ra, Hyun-Soo; Kim, Jinkwon; Lee, Jong-Soo

    2016-04-01

    Copper based ternary and quaternary semiconductor nanostructures are of great interest for the fabrication of low cost photovoltaics. Although well-developed syntheses are available for zero dimensional (0D) nanoparticles, colloidal synthesis of two dimensional (2D) nanosheets remains a big challenge. Here we report, for the first time, a simple and reproducible cation exchange approach for 2D colloidal Cu2GeSe3, Cu2ZnGeSe4 and their alloyed Cu2GeSxSe3-x, Cu2ZnGeSxSe4-x nanosheets using pre-synthesized Cu2xSe nanosheets as a template. A mechanism for the formation of Cu2-xSe nanosheets has been studied in detail. In situ oxidation of Cu+ ions to form a CuSe secondary phase facilitates the formation of Cu2-xSe NSs. The obtained ternary and quaternary nanosheets have average lateral size in micrometers and thickness less than 5 nm. This method is general and can be extended to produce other important ternary semiconductor nanosheets such as CuIn1-xGaxSe2. The optical band gap of these nanosheets is tuned from 1 to 1.48 eV, depending on their composition.Copper based ternary and quaternary semiconductor nanostructures are of great interest for the fabrication of low cost photovoltaics. Although well-developed syntheses are available for zero dimensional (0D) nanoparticles, colloidal synthesis of two dimensional (2D) nanosheets remains a big challenge. Here we report, for the first time, a simple and reproducible cation exchange approach for 2D colloidal Cu2GeSe3, Cu2ZnGeSe4 and their alloyed Cu2GeSxSe3-x, Cu2ZnGeSxSe4-x nanosheets using pre-synthesized Cu2xSe nanosheets as a template. A mechanism for the formation of Cu2-xSe nanosheets has been studied in detail. In situ oxidation of Cu+ ions to form a CuSe secondary phase facilitates the formation of Cu2-xSe NSs. The obtained ternary and quaternary nanosheets have average lateral size in micrometers and thickness less than 5 nm. This method is general and can be extended to produce other important ternary

  14. Plant cation/H(+) exchangers (CAXs): biological functions and genetic manipulations

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Inorganic cations play decisive roles in many cellular and physiological processes and are essential components of plant nutrition. Therefore, the uptake of cations and their redistribution must be precisely controlled. Vacuolar antiporters are important elements in mediating the intracellular seque...

  15. Stationary phase-related investigations of quinine-based zwitterionic chiral stationary phases operated in anion-, cation-, and zwitterion-exchange modes.

    PubMed

    Hoffmann, Christian V; Reischl, Roland; Maier, Norbert M; Lämmerhofer, Michael; Lindner, Wolfgang

    2009-02-13

    The concept of recently introduced Cinchona alkaloid-type zwitterionic chiral stationary phases (CSPs) is based on fusing key cation- and anion-exchange (CX, AX) moieties in one single low-molecular mass chiral selector (SO) with the resulting CSPs allowing enantiomer separations of a wide range of chiral ionizable analytes comprising acids, bases, and zwitterionic compounds. Herein, we report principal, systematic investigations of the ion-exchange-type retention mechanisms available with the novel zwitterionic CSPs in nonaqueous polar organic mode. Typical CX and AX processes, corresponding to the parent single ion exchangers, are confirmed also for zwitterionic CSPs. Also the mechanism leading to recognition and retention of zwitterions was found to be ion exchange mediated in a zwitterion-exchange (ZX) mode. In both AX and CX modes the additional ionizable group within the SO besides the site responsible for the respective ion-exchange process could be characterized as an intramolecular counterion (IMCI) that effectively participates in the ion-exchange equilibria and thus, contributes to solute elution. In the ZX mode both oppositely charged groups of the zwitterionic SO were found not only to be the sites for simultaneous ion pairing with the analyte but also functioned as IMCIs at the same time. The main practical consequences of the IMCI feature were significant reduction of the amounts and even elimination of acidic and basic additives required in the eluent systems to afford analyte elution while still providing faster analysis than the parent single ion-exchanger-type CSPs. The set of ten structurally different zwitterionic CSPs employed in this study facilitated the establishment of correlations between chromatographic behavior of the CSPs with particular SO elements, thereby supporting the understanding of the working principles of these novel packing materials on a molecular level.

  16. [Preparation of a strong cation-exchange polymer monolith and its application in determination of melamine in milk products].

    PubMed

    Ma, Qiao; Hu, Xizhou; Huang, Jincui; Feng, Yuqi

    2009-09-01

    A poly (2-acrylamido-2-methyl-1-propanesulfonic acid-co-ethylene dimethacrylate) (AMPS-co-EDMA) monolith was prepared in a fused-silica capillary (530 microm i.d.) and applied for polymer monolith microextraction (PMME). With the optimal ratio of N, N-dimethyl-formamide (DMF, porogen) and polyethylene glycol (PEG, co-porogen), the resulting monolith exhibited satisfactory permeability, high mechanical strength and good stability in aqueous buffer. The effects of several parameters to PMME were investigated, such as pH value, inorganic salt and organic phase concentration of the sample matrix. It demonstrated that the melamine was captured on the poly (AMPS-co-EDMA) monolith mainly through strong cation-exchange and hydrophobic interactions. A novel approach is presented for the determination of melamine in milk products by coupling PMME to high performance liquid chromatography with ultraviolet detection. Because of the high extraction capacity of the monolith towards melamine, low detection limits (S/N = 3, 0.9 mg/kg) and quantification limits (S/N = 10, 0.3 mg/kg) were obtained. The method showed good linearity ranging from 0.5 to 80 mg/kg. Excellent reproducibility of the method was exhibited by intraday and interday precisions, yielding the relative standard deviations not larger than 7.5%. The proposed method is simple, rapid, sensitive, and low cost.

  17. Sorption of chlorimuron-ethyl on montmorillonite clays: effects of exchangeable cations, pH, and ionic strength.

    PubMed

    Ren, Wenjie; Teng, Ying; Zhou, Qixing; Paschke, Albrecht; Schüürmann, Gerrit

    2014-10-01

    Sorption interaction of chlorimuron-ethyl with montmorillonite clays was investigated under varied types of exchangeable cation, pH, and ionic strength conditions. Chlorimuron-ethyl sorption on bentonites exhibited pronounced cation dependency, and the sorption ability increased as the sequence Ca(2+)- < Na(+)- < Al(3+)- < Fe(3+)-bentonite, due to different sorption mechanisms, whereas the cation dependency was influenced by the clay type and much weaker for montmorillonites. The decrease of pH at the range of 4.0-6.0 prominently increased sorption of chlorimuron-ethyl on all cation-exchanged montmorillonite clays, and nearly a neglected sorption (about 2 %) can be observed at pH over 7.0. In the presence of CaCl2, sorption of chlorimuron-ethyl on Fe(3+)-bentonite was promoted because of complexion of Ca(2+) and the surface of Fe(3+)-bentonite. However, as the concentration of CaCl2 increased, chlorimuron-ethyl sorption on Ca(2+)- and Fe(3+)-exchanged bentonite decreased, suggesting that Ca bridging was not the prevailing mechanism for sorption of chlorimuron-ethyl on these clays. Furthermore, chlorimuron-ethyl sorption was relatively sensitive to pH, and the change of pH may obscure effect of other factors on the sorption, so it was quite necessary to control pH at a constant value when the effect of other factor was being studied. PMID:25028319

  18. Influence of competing inorganic cations on the ion exchange equilibrium of the monovalent organic cation metoprolol on natural sediment.

    PubMed

    Niedbala, Anne; Schaffer, Mario; Licha, Tobias; Nödler, Karsten; Börnick, Hilmar; Ruppert, Hans; Worch, Eckhard

    2013-02-01

    The aim of this study was to systematically investigate the influence of the mono- and divalent inorganic ions Na(+) and Ca(2+) on the sorption behavior of the monovalent organic cation metoprolol on a natural sandy sediment at pH=7. Isotherms for the beta-blocker metoprolol were obtained by sediment-water batch tests over a wide concentration range (1-100000 μg L(-1)). Concentrations of the competing inorganic ions were varied within freshwater relevant ranges. Data fitted well with the Freundlich sorption model and resulted in very similar Freundlich exponents (n=0.9), indicating slightly non-linear behavior. Results show that the influence of Ca(2+) compared to Na(+) is more pronounced. A logarithmic correlation between the Freundlich coefficient K(Fr) and the concentration or activity of the competing inorganic ions was found allowing the prediction of metoprolol sorption on the investigated sediment at different electrolyte concentrations. Additionally, the organic carbon of the sediment was completely removed for investigating the influence of organic matter on the sorption of metoprolol. The comparison between the experiments with and without organic carbon removal revealed no significant contribution of the organic carbon fraction (0.1%) to the sorption of metoprolol on the in this study investigated sediment. Results of this study will contribute to the development of predictive models for the transport of organic cations in the subsurface.

  19. On-column refolding of bone morphogenetic protein-2 using cation exchange resin.

    PubMed

    Rane, Anuja M; Jonnalagadda, Sriramakamal; Li, Zhiyu

    2013-08-01

    Refolding is often the bottle-neck step in producing recombinant proteins from inclusion bodies of Escherichia coli, especially for dimer proteins. The refolding process is protein specific, engaging a lot of time and cost to optimize conditions so that the thermodynamics favor protein refolding over competitive aggregation. Bone morphogenetic protein-2 (BMP-2) is a potent osteogenic agent having significant applications in bone regeneration therapy. In this study, we present a novel solid-phase refolding method for rapid and efficient refolding of recombinant BMP-2 dimer from E. coli. We employed a weak cation exchange resin as the adsorbing support, with decreasing gradient of denaturing agent and exposure to oxidizing conditions for adequate disulfide bond formation. Refolded BMP-2 was further purified using size exclusion chromatography and analyzed for its secondary structure and biological activity. The purified BMP-2 dimer showed dose-dependent induction of alkaline phosphatase (ALP) activity in MC3T3 pre-osteoblast cells, thus translating the success of our refolding method. This simple and rapid method can also be applied in refolding and purification of other BMP-2 like dimer proteins. PMID:23748143

  20. Isolation of lactoperoxidase using different cation exchange resins by batch and column procedures.

    PubMed

    Fweja, Leonard Wt; Lewis, Michael J; Grandison, Alistair S

    2010-08-01

    Lactoperoxidase (LP) was isolated from whey protein by cation-exchange using Carboxymethyl resin (CM-25C) and Sulphopropyl Toyopearl resin (SP-650C). Both batch and column procedures were employed and the adsorption capacities and extraction efficiencies were compared. The resin bed volume to whey volume ratios were 0.96:1.0 for CM-25C and 0.64:1.0 for SP-650 indicating higher adsorption capacity of SP-650 compared with CM-25C. The effluent LP activity depended on both the enzyme activity in the whey and the amount of whey loaded on the column within the saturation limits of the resin. The percentage recovery was high below the saturation point and fell off rapidly with over-saturation. While effective recovery was achieved with column extraction procedures, the recovery was poor in batch procedures. The whey-resin contact time had little impact on the enzyme adsorption. SDS PAGE and HPLC analyses were also carried out, the purity was examined and the proteins characterised in terms of molecular weights. Reversed phase HPLC provided clear distinction of the LP and lactoferrin (LF) peaks. The enzyme purity was higher in column effluents compared with batch effluents, judged on the basis of the clarity of the gel bands and the resolved peaks in HPLC chromatograms.

  1. Nitrogen removal from wastewater through microbial electrolysis cells and cation exchange membrane

    PubMed Central

    2014-01-01

    Vulnerability of water resources to nutrients led to progressively stricter standards for wastewater effluents. Modification of the conventional procedures to meet the new standards is inevitable. New technologies should give a priority to nitrogen removal. In this paper, ammonium chloride and urine as nitrogen sources were used to investigate the capacity of a microbial electrolysis cell (MEC) configured by cation exchange membrane (CEM) for electrochemical removal of nitrogen over open-and closed-circuit potentials (OCP and CCP) during biodegradation of organic matter. Results obtained from this study indicated that CEM was permeable to both organic and ammonium nitrogen over OCP. Power substantially mediated ammonium migration from anodic wastewater to the cathode, as well. With a urine rich wastewater in the anode, the maximum rate of ammonium intake into the cathode varied from 34.2 to 40.6 mg/L.h over CCP compared to 10.5-14.9 mg/L.h over OCP. Ammonium separation over CCP was directly related to current. For 1.46-2.12 mmol electron produced, 20.5-29.7 mg-N ammonium was removed. Current also increased cathodic pH up to 12, a desirable pH for changing ammonium ion to ammonia gas. Results emphasized the potential for MEC in control of ammonium through ammonium separation and ammonia volatilization provided that membrane characteristic is considered in their development. PMID:24533446

  2. Morphology and microtopology of cation-exchange polymers and the origin of the overlimiting current.

    PubMed

    Balster, J; Yildirim, M H; Stamatialis, D F; Ibanez, R; Lammertink, R G H; Jordan, V; Wessling, M

    2007-03-01

    In electrodialysis desalination processes, the operating current density is limited by concentration polarization. In contrast to other membrane processes such as ultrafiltration, in electrodialysis, current transport above the limiting current is possible. In this work, the origin of the overlimiting current at cation-exchange polymers is investigated. We show that, under certain experimental conditions, electroconvection is the origin of the overlimiting conductance. The theory concerning electroconvection predicts a shortening of the plateau length of membranes with increased conductive or geometrical heterogeneity. We investigate the influence of these two parameters and show that the creation of line undulations on the membrane surface normal to the flow direction, having distances in the range of approximately 50-200% of the boundary-layer thickness, lead to an earlier onset of the overlimiting current. The plateau length of the undulated membranes is reduced by up to 60% compared to that of a flat membrane. These results verify the existence of electroconvection as a mechanism destabilizing the laminar boundary layer at the liquid-membrane interface and causing ionic transport above the limiting current density.

  3. Forensic analysis of hallucinogenic mushrooms and khat (Catha edulis Forsk) using cation-exchange liquid chromatography.

    PubMed

    Laussmann, Tim; Meier-Giebing, Sigrid

    2010-02-25

    Hallucinogenic mushrooms (e.g. Psilocybe and Panaeolus species) as well as leaves and young shoots of the khat tree (Catha edulis Forsk) are illicit drugs in many countries. The exact concentration of the hallucinogenic alkaloids psilocin and psilocybin in mushrooms and the sympathomimetic alkaloids cathinone and cathine in khat is usually essential for jurisdiction. Facing an increasing number of mushroom and khat seizures by German customs authorities, a convenient comprehensive quantitative HPLC method based on cation-exchange liquid chromatography for these rather "exotic" drugs has been developed which avoids time-consuming multi-step sample preparation or chemical derivatization procedures. Using this method a number of different hallucinogenic fungi species and products that are mainly distributed via the internet have been analysed (dried and fresh Psilocybe cubensis Singer as well as P. cubensis collected from "grow boxes", Panaeolus cyanescens Berkeley and Broome and so-called "philosopher stones" (sclerotia of Psilocybe species)). Highest total amounts of psilocin have been detected in dried P. cyanescens reaching up to 3.00+/-0.24 mg per 100 mg. The distribution of khat alkaloids in different parts of the khat shoots has been studied. High concentrations of cathinone have not only been detected in leaves but also in green parts and barks of stalks. Additionally, the sample treatment for fresh mushroom and khat samples has been optimised. Highest amounts of alkaloids were found when fresh material was freeze-dried.

  4. Adsorption equilibrium and kinetics of monomer-dimer monoclonal antibody mixtures on a cation exchange resin.

    PubMed

    Reck, Jason M; Pabst, Timothy M; Hunter, Alan K; Wang, Xiangyang; Carta, Giorgio

    2015-07-10

    Adsorption equilibrium and kinetics are determined for a monoclonal antibody (mAb) monomer and dimer species, individually and in mixtures, on a macroporous cation exchange resin both under the dilute limit of salt gradient elution chromatography and at high protein loads and low salt based on batch adsorption equilibrium and confocal laser scanning microscopy (CLSM) experiments. In the dilute limit and weak binding conditions, the dimer/monomer selectivity in 10mM phosphate at pH 7 varies between 8.7 and 2.3 decreasing with salt concentration in the range of 170-230mM NaCl. At high protein loads and strong binding conditions (0-60mM NaCl), the selectivity in the same buffer is near unity with no NaCl added, but increases gradually with salt concentration reaching high values between 2 and 15 with 60mM added NaCl. For these conditions, the two-component adsorption kinetics is controlled by pore diffusion and is predicted approximately by a dual shrinking core model using parameters based on single component equilibrium and kinetics measurements.

  5. Cation- and anion-exchanges induce multiple distinct rearrangements within metallosupramolecular architectures.

    PubMed

    Riddell, Imogen A; Ronson, Tanya K; Clegg, Jack K; Wood, Christopher S; Bilbeisi, Rana A; Nitschke, Jonathan R

    2014-07-01

    Different anionic templates act to give rise to four distinct Cd(II)-based architectures: a Cd2L3 helicate, a Cd8L12 distorted cuboid, a Cd10L15 pentagonal prism, and a Cd12L18 hexagonal prism, which respond to both anionic and cationic components. Interconversions between architectures are driven by the addition of anions that bind more strongly within a given product framework. The addition of Fe(II) prompted metal exchange and transformation to a Fe4L6 tetrahedron or a Fe10L15 pentagonal prism, depending on the anionic templates present. The equilibrium between the Cd12L18 prism and the Cd2L3 triple helicate displayed concentration dependence, with higher concentrations favoring the prism. The Cd12L18 structure serves as an intermediate en route to a hexafluoroarsenate-templated Cd10L15 complex, whereby the structural features of the hexagonal prism preorganize the system to form the structurally related pentagonal prism. In addition to the interconversion pathways investigated, we also report the single-crystal X-ray structure of bifluoride encapsulated within a Cd10L15 complex and report solution state data for J-coupling through a CH···F(-) hydrogen bond indicating the strength of these interactions in solution.

  6. Adsorption equilibrium and kinetics of monomer-dimer monoclonal antibody mixtures on a cation exchange resin.

    PubMed

    Reck, Jason M; Pabst, Timothy M; Hunter, Alan K; Wang, Xiangyang; Carta, Giorgio

    2015-07-10

    Adsorption equilibrium and kinetics are determined for a monoclonal antibody (mAb) monomer and dimer species, individually and in mixtures, on a macroporous cation exchange resin both under the dilute limit of salt gradient elution chromatography and at high protein loads and low salt based on batch adsorption equilibrium and confocal laser scanning microscopy (CLSM) experiments. In the dilute limit and weak binding conditions, the dimer/monomer selectivity in 10mM phosphate at pH 7 varies between 8.7 and 2.3 decreasing with salt concentration in the range of 170-230mM NaCl. At high protein loads and strong binding conditions (0-60mM NaCl), the selectivity in the same buffer is near unity with no NaCl added, but increases gradually with salt concentration reaching high values between 2 and 15 with 60mM added NaCl. For these conditions, the two-component adsorption kinetics is controlled by pore diffusion and is predicted approximately by a dual shrinking core model using parameters based on single component equilibrium and kinetics measurements. PMID:26028510

  7. Mineral carbonation of gaseous carbon dioxide using a clay-hosted cation exchange reaction.

    PubMed

    Kang, Il-Mo; Roh, Ki-Min

    2013-01-01

    The mineral carbonation method is still a challenge in practical application owing to: (1) slow reaction kinetics, (2) high reaction temperature, and (3) continuous mineral consumption. These constraints stem from the mode of supplying alkaline earth metals through mineral acidification and dissolution. Here, we attempt to mineralize gaseous carbon dioxide into calcium carbonate, using a cation exchange reaction of vermiculite (a species of expandable clay minerals). The mineralization is operated by draining NaCI solution through vermiculite powders and continuously dropping into the pool of NaOH solution with CO2 gas injected. The mineralization temperature is regulated here at 293 and 333 K for 15 min. As a result of characterization, using an X-ray powder diffractometer and a scanning electron microscopy, two types of pure CaCO3 polymorphs (vaterite and calcite) are identified as main reaction products. Their abundance and morphology are heavily dependent on the mineralization temperature. Noticeably, spindle-shaped vaterite, which is quite different from a typical vaterite morphology (polycrystalline spherulite), forms predominantly at 333 K (approximately 98 wt%).

  8. Detection and characterization of carrier-mediated cationic amino acid transport in lysosomes of normal and cystinotic human fibroblasts. Role in therapeutic cystine removal

    SciTech Connect

    Pisoni, R.L.; Thoene, J.G.; Christensen, H.N.

    1985-04-25

    The discovery of a trans-stimulation property associated with lysine exodus from lysosomes of human fibroblasts has enabled us to characterize a system mediating the transport of cationic amino acids across the lysosomal membrane of human fibroblasts. The cationic amino acids arginine, lysine, ornithine, diaminobutyrate, histidine, 2-aminoethylcysteine, and the mixed disulfide of cysteine and cysteamine all caused trans-stimulation of the exodus of radiolabeled lysine from the lysosomal fraction of human fibroblasts at pH 6.5. In contrast, neutral and acidic amino acids did not affect the rate of lysine exodus. Trans-stimulation of lysine exodus was observed over the pH range from 5.5 to 7.6, was specific for the L-isomer of the cationic amino acid, and was intolerant to methylation of the alpha-amino group of the amino acid. The lysosomotropic amine, chloroquine, greatly retarded lysine exodus, whereas the presence of sodium ion was without effect. The specificity and lack of Na+ dependence of this lysosomal transport system is similar to that of System y+ present on the plasma membrane of human fibroblasts. An important mechanism by which cysteamine treatment of cystinosis allows cystine escape from lysosomes may be the ability of the mixed disulfide of cysteine and cysteamine formed by sulfhydryl-disulfide exchange to migrate by this newly discovered system mediating cationic amino acid transport.

  9. How Lewis acidic is your cation? Putting phosphenium ions on the fluoride ion affinity scale.

    PubMed

    Slattery, John M; Hussein, Sharifa

    2012-02-14

    The fluoride ion affinities (FIAs) of 33 phosphenium ions with a range of substituents were calculated using ab inito and DFT methods. The use of these FIA data as a measure of the Lewis acidities of phosphenium ions is described and the FIAs of the species studied here are compared to FIA data for more commonly encountered Lewis acids. Phosphenium ions are often stronger Lewis acids than neutral species, but in many cases are less Lewis acidic than highly electrophilic cations such as [Me(3)C](+) or [Me(3)Si](+). The impact of mesomeric, inductive and steric substituent effects on FIAs are discussed and related to the underlying electronic structures of different cation types. A comparison between the FIAs of known "free" phosphenium ions with those that are currently unknown and other highly electrophilic cations suggests that some diaryl- and dialkylphosphenium ions may yet be accessible under the right conditions. PMID:22159000

  10. Modulation of the serine base exchange enzyme activity of rat brain membranes by amphiphilic cations and amphiphilic anions.

    PubMed

    Kanfer, J N; McCartney, D G

    1993-04-01

    The biosynthesis of phosphatidylserine in mammalian tissues is catalyzed by the serine base exchange enzyme. The activity of this membrane-bound enzyme can be manipulated by amphiphiles. Amphiphilic cations, such as oleylamine, W-7, chlorpromazine, and didodecyldimethylamine, stimulate the serine base exchange activity. Amphiphilic anions, such as bis(2-ethylhexyl) hydrogen phosphate and cholesterol sulfate, inhibit the serine base exchange activity. These effects are more pronounced at pH 7.0 than at the pH optimum of 8.5 for this enzyme. Both the stimulators and the inhibitors alter the Vmax values without changing the Km value for serine, suggesting that their mechanism of action is related to interactions of the membrane-bound cosubstrate, phosphatidylethanolamine, with the membrane-bound enzyme. The optimal concentration of stimulator varies with the amount of membrane protein present; however, supraoptimal concentrations cause inhibitions. It is proposed that the amphiphilic cations enhance the interaction of the phosphorylethanolamine moiety of the membrane-bound cosubstrate with the enzyme and the amphiphilic anions interfere with such an interaction. Some of the pharmacological properties of these amphiphilic cations, employed clinically as antidepressants, may be mediated by modulation of the serine base exchange enzyme activity.

  11. KINETIC ASPECTS OF CATION-ENHANCED AGGREGATION IN AQUEOUS HUMIC ACIDS. (R822832)

    EPA Science Inventory

    The cation-enhanced formation of hydrophobic domains in aqueous humic acids has been shown to be a slow process, consistent with the evolution and disintegration of humic acid configurations over periods lasting from days to weeks. After the addition of a magnesium salt to a humi...

  12. Kinetic Analyses of Cation Exchange Rates in Synthetic Birnessite Measured by Time- Resolved Synchrotron X-ray Diffraction

    NASA Astrophysics Data System (ADS)

    Lopano, C. L.; Heaney, P. J.; Post, J. E.; Bandstra, J.; Brantley, S. L.

    2006-05-01

    Birnessite is the most abundant and chemically important layer-structure Mn-oxide phase found in soils, desert varnishes, and ocean nodules. It also is industrially important for use in battery technology and octahedral sieves. Due to the poorly crystalline nature of natural birnessite, synthetic analogues typically have been employed in studies that explore the structural response of birnessite to variations in interlayer composition. For this work, we measured changes in unit-cell parameters over time to quantify the degree of cation exchange as a function of concentration. Aqueous K+, Cs+, and Ba2+ cations at varying concentrations at pH 7 were exchanged for interlayer Na+ in synthetic birnessite (Na0.58(Mn4+1.42,Mn3+0.58)O4·1.5H2O) using a simple flow- through cell, and the exchange products were monitored via time-resolved X-ray powder diffraction at the National Synchrotron Light Source. Powder X-ray diffraction patterns were collected every 2-3 minutes. Rietveld analyses of X-ray diffraction patterns for K- and Ba-exchanged birnessite revealed a decrease in unit- cell volume over time. In contrast, Cs+ substitution increased cell volume. For all three cations, the crystallographic data indicate that exchange occurred in two stages. A rapid and dramatic change in unit-cell volume was followed by a modest adjustment over longer timescales. Fourier electron difference syntheses revealed that the rapid, initial stage of exchange was marked by re-configuration of the interlayer species, whereas the second, protracted phase of substitution represented ordering into the newly established interlayer positions. For the first time, we have modeled the kinetics of interlayer substitution in Na-birnessite. For purposes of comparison, we have employed a simple one-stage reaction (i.e., Na-birnessite → K-birnessite) and a two stage reaction (i.e,. Na-birnessite → K-birnessitedisordered → K- birnessiteordered). For exchange with 0.01 M KCl solutions, the single

  13. Kinetics of esterification of acidified oil with different alcohols by a cation ion-exchange resin/polyethersulfone hybrid catalytic membrane.

    PubMed

    Zhang, Honglei; Ding, Jincheng; Qiu, Yanli; Zhao, Zengdian

    2012-05-01

    Hybrid catalytic membranes consisting of cation ion-exchange resin particles (CERP) and polyethersulfone (PES) were prepared by immersion phase inversion and used as heterogeneous catalysts for the esterification of acidified oil with methanol, ethanol, propanol and butanol. The membranes were characterized by ion exchange capacity and swelling degree tests. The membranes were annealed at different temperatures to improve catalytic activity and membranes annealed at 393 K had the highest catalytic activity. Butanol allowed the highest free fatty acids (FFAs) conversion of 95.28% since it has better miscibility than the other alcohols which strengthened mass and heat transfer. Furthermore, pseudo-homogeneous kinetic models of the esterification of acidified oil with the four alcohols were established according to the experimental data. The kinetic models can well predict the FFA conversion. PMID:22424925

  14. Anion- or Cation-Exchange Membranes for NaBH4/H2O2 Fuel Cells?

    PubMed Central

    Šljukić, Biljana; Morais, Ana L.; Santos, Diogo M. F.; Sequeira, César A. C.

    2012-01-01

    Direct borohydride fuel cells (DBFC), which operate on sodium borohydride (NaBH4) as the fuel, and hydrogen peroxide (H2O2) as the oxidant, are receiving increasing attention. This is due to their promising use as power sources for space and underwater applications, where air is not available and gas storage poses obvious problems. One key factor to improve the performance of DBFCs concerns the type of separator used. Both anion- and cation-exchange membranes may be considered as potential separators for DBFC. In the present paper, the effect of the membrane type on the performance of laboratory NaBH4/H2O2 fuel cells using Pt electrodes is studied at room temperature. Two commercial ion-exchange membranes from Membranes International Inc., an anion-exchange membrane (AMI-7001S) and a cation-exchange membrane (CMI-7000S), are tested as ionic separators for the DBFC. The membranes are compared directly by the observation and analysis of the corresponding DBFC’s performance. Cell polarization, power density, stability, and durability tests are used in the membranes’ evaluation. Energy densities and specific capacities are estimated. Most tests conducted, clearly indicate a superior performance of the cation-exchange membranes over the anion-exchange membrane. The two membranes are also compared with several other previously tested commercial membranes. For long term cell operation, these membranes seem to outperform the stability of the benchmark Nafion membranes but further studies are still required to improve their instantaneous power load. PMID:24958292

  15. Preparation of Cation-Exchange Particle Designed for High-Speed Collection of Proteins by Radiation-Induced Graft Polymerization

    NASA Astrophysics Data System (ADS)

    Sekiya, Yuta; Shimoda, Yuichi; Umeno, Daisuke; Saito, Kyoichi; Furumoto, Goro; Shirataki, Hironobu; Shinohara, Naoyuki; Kubota, Noboru

    A cation-exchange polymer brush was immobilized onto a polyethylene-based particle with an average diameter of 35 μm by radiation-induced graft polymerization of glycidyl methacrylate and subsequent sulfonation with sodium sulfite. A lysozyme solution was forced to flow through a bed (height 2 cm, cross-sectional area 0.61 cm2) charged with the resultant cation-exchange particles at a space velocity ranging from 500 to 2300 h-1. From a viewpoint of equilibrium binding capacity and elution percentage of lysozyme, the dose of electron beam and the degree of GMA grafting were optimized to be 200 kGy and 100%, respectively. The bed exhibited a constant dynamic binding capacity of lysozyme 14 mg⁄mL irrespective of space velocity due to negligible diffusional mass-transfer resistance.

  16. Modelling of geochemical reactions and experimental cation exchange in MX 80 bentonite.

    PubMed

    Montes-H, G; Fritz, B; Clement, A; Michau, N

    2005-10-01

    Bentonites are widely used for waste repository systems because of their hydrodynamic, surface and chemical-retention properties. MX 80 bentonite (bentonite of Wyoming) contains approximately 85% Na/Ca-montmorillonite and 15% accessory minerals. The dominant presence of Na/Ca-montmorillonite in this clay mineral could cause it to perform exceptionally well as an engineered barrier for a radioactive waste repository because this buffer material is expected to fill up by swelling the void between canisters containing waste and the surrounding ground. However, the Na/Ca-montmorillonite could be transformed to other clay minerals as a function of time under repository conditions. Previous modelling studies based on the hydrolysis reactions have shown that the Na/Ca-montmorillonite-to-Ca-montmorillonite conversion is the most significant chemical transformation. In fact, this chemical process appears to be a simple cation exchange into the engineered barrier. The purpose of the present study was two-fold. Firstly, it was hoped to predict the newly formed products of bentonite-fluid reactions under repository conditions by applying a thermokinetic hydrochemical code (KIRMAT: Kinetic Reactions and Mass Transport). The system modelled herein was considered to consist of a 1-m thick zone of water-saturated engineered barrier. This non-equilibrated system was placed in contact with a geological fluid on one side, which was then allowed to diffuse into the barrier, while the other side was kept in contact with iron-charged water. Reducing initial conditions ( [P(O)2 approximately equals 0] ; Eh=-200 mV) and a constant reaction temperature (100 degrees C) were considered. Secondly, it was hoped to estimate the influence of inter-layer cations (Ca and Na) on the swelling behaviour of the MX 80 bentonite by using an isothermal system of water vapour adsorption and an environmental scanning electron microscope (ESEM) coupled with a digital image analysis (DIA) program. Here, the

  17. Does Cation Size Affect Occupancy and Electrostatic Screening of the Nucleic Acid Ion Atmosphere?

    PubMed

    Gebala, Magdalena; Bonilla, Steve; Bisaria, Namita; Herschlag, Daniel

    2016-08-31

    Electrostatics are central to all aspects of nucleic acid behavior, including their folding, condensation, and binding to other molecules, and the energetics of these processes are profoundly influenced by the ion atmosphere that surrounds nucleic acids. Given the highly complex and dynamic nature of the ion atmosphere, understanding its properties and effects will require synergy between computational modeling and experiment. Prior computational models and experiments suggest that cation occupancy in the ion atmosphere depends on the size of the cation. However, the computational models have not been independently tested, and the experimentally observed effects were small. Here, we evaluate a computational model of ion size effects by experimentally testing a blind prediction made from that model, and we present additional experimental results that extend our understanding of the ion atmosphere. Giambasu et al. developed and implemented a three-dimensional reference interaction site (3D-RISM) model for monovalent cations surrounding DNA and RNA helices, and this model predicts that Na(+) would outcompete Cs(+) by 1.8-2.1-fold; i.e., with Cs(+) in 2-fold excess of Na(+) the ion atmosphere would contain an equal number of each cation (Nucleic Acids Res. 2015, 43, 8405). However, our ion counting experiments indicate that there is no significant preference for Na(+) over Cs(+). There is an ∼25% preferential occupancy of Li(+) over larger cations in the ion atmosphere but, counter to general expectations from existing models, no size dependence for the other alkali metal ions. Further, we followed the folding of the P4-P6 RNA and showed that differences in folding with different alkali metal ions observed at high concentration arise from cation-anion interactions and not cation size effects. Overall, our results provide a critical test of a computational prediction, fundamental information about ion atmosphere properties, and parameters that will aid in the

  18. Probing the Complementarity of FAIMS and Strong Cation Exchange Chromatography in Shotgun Proteomics

    NASA Astrophysics Data System (ADS)

    Creese, Andrew J.; Shimwell, Neil J.; Larkins, Katherine P. B.; Heath, John K.; Cooper, Helen J.

    2013-03-01

    High field asymmetric waveform ion mobility spectrometry (FAIMS), also known as differential ion mobility spectrometry, coupled with liquid chromatography tandem mass spectrometry (LC-MS/MS) offers benefits for the analysis of complex proteomics samples. Advantages include increased dynamic range, increased signal-to-noise, and reduced interference from ions of similar m/ z. FAIMS also separates isomers and positional variants. An alternative, and more established, method of reducing sample complexity is prefractionation by use of strong cation exchange chromatography. Here, we have compared SCX-LC-MS/MS with LC-FAIMS-MS/MS for the identification of peptides and proteins from whole cell lysates from the breast carcinoma SUM52 cell line. Two FAIMS approaches are considered: (1) multiple compensation voltages within a single LC-MS/MS analysis (internal stepping) and (2) repeat LC-MS/MS analyses at different and fixed compensation voltages (external stepping). We also consider the consequence of the fragmentation method (electron transfer dissociation or collision-induced dissociation) on the workflow performance. The external stepping approach resulted in a greater number of protein and peptide identifications than the internal stepping approach for both ETD and CID MS/MS, suggesting that this should be the method of choice for FAIMS proteomics experiments. The overlap in protein identifications from the SCX method and the external FAIMS method was ~25 % for both ETD and CID, and for peptides was less than 20 %. The lack of overlap between FAIMS and SCX highlights the complementarity of the two techniques. Charge state analysis of the peptide assignments showed that the FAIMS approach identified a much greater proportion of triply-charged ions.

  19. Cation exchange capacity of loess and overlying soil in the non-carbonate loess sections, North-Western Croatia

    NASA Astrophysics Data System (ADS)

    Tomašić, Nenad; Kampić, Štefica; Cindrić, Iva Juranović; Pikelj, Kristina; Lučić, Mavro; Mavrić, Danijela; Vučetić, Tajana

    2013-12-01

    The adsorption properties in terms of cation exchange capacity and their relation to the soil and sediment constituents (clay minerals, Fe-, Mn-, and Al-oxyhydroxides, organic matter) were investigated in loess, soil-loess transition zone, and soil at four loess-soil sections in North-Western Croatia. Cation exchange capacity of the bulk samples, the samples after oxalate extraction of Fe, Mn and Al, and after removal of organic matter, as well as of the separated clay fraction, was determined using copper ethylenediamine. Cation exchange capacity (pH˜7) of the bulk samples ranges from 5 to 12 cmol c /kg in soil, from 7 to 15 cmol c /kg in the soil-loess transition zone, and from 12 to 20 cmol c /kg in loess. Generally, CEC values increase with depth. Oxalate extraction of Fe, Mn, and Al, and removal of organic matter cause a CEC decrease of 3-38% and 8-55%, respectively, proving a considerable influence of these constituents to the bulk CEC values. In the separated clay fraction (<2 μm) CEC values are up to several times higher relative to those in the bulk samples. The measured CEC values of the bulk samples generally correspond to the clay mineral content identified. Also, a slight increase in muscovite/illite content with depth and the vermiculite occurrence in the loess horizon are concomitant with the CEC increase in deeper horizons, irrespective of the sample pretreatment.

  20. Cation exchange capacity of loess and overlying soil in the non-carbonate loess sections, North-Western Croatia

    NASA Astrophysics Data System (ADS)

    Tomašić, Nenad; Kampić, Štefica; Cindrić, Iva; Pikelj, Kristina; Lučić, Mavro; Mavrić, Danijela; Vučetić, Tajana

    2013-12-01

    The adsorption properties in terms of cation exchange capacity and their relation to the soil and sediment constituents (clay minerals, Fe-, Mn-, and Al-oxyhydroxides, organic matter) were investigated in loess, soil-loess transition zone, and soil at four loess-soil sections in North-Western Croatia. Cation exchange capacity of the bulk samples, the samples after oxalate extraction of Fe, Mn and Al, and after removal of organic matter, as well as of the separated clay fraction, was determined using copper ethylenediamine. Cation exchange capacity (pH˜7) of the bulk samples ranges from 5 to 12 cmolc/kg in soil, from 7 to 15 cmolc/kg in the soil-loess transition zone, and from 12 to 20 cmolc/kg in loess. Generally, CEC values increase with depth. Oxalate extraction of Fe, Mn, and Al, and removal of organic matter cause a CEC decrease of 3-38% and 8-55%, respectively, proving a considerable influence of these constituents to the bulk CEC values. In the separated clay fraction (<2 μm) CEC values are up to several times higher relative to those in the bulk samples. The measured CEC values of the bulk samples generally correspond to the clay mineral content identified. Also, a slight increase in muscovite/illite content with depth and the vermiculite occurrence in the loess horizon are concomitant with the CEC increase in deeper horizons, irrespective of the sample pretreatment.

  1. Retardation of ammonium and potassium transport through a contaminated sand and gravel aquifer: The Role of cation exchange

    USGS Publications Warehouse

    Ceazan, M.L.; Thurman, E.M.; Smith, R.L.

    1989-01-01

    The role of cation exchange in the retardation of ammonium (NH4+) and potassium (K+) transport in a shallow sand and gravel aquifer was evaluated by use of observed distributions of NH4+ and K+ within a plume of sewage-contaminated groundwater, small-scale tracer injection tests, and batch sorption experiments on aquifer material. Both NH4+ and K+ were transported ???2 km in the 4-km-long contaminant plume (retardation factor, Rf = 2.0). Sediments from the NH4+-containing zone of the plume contained significant quantities of KCl-extractable NH4+ (extraction distribution coefficient, Kd,extr = 0.59-0.87 mL/g of dry sediment), and when added to uncontaminated sediments, NH4+ sorption followed a linear isotherm. Small-scale tracer tests demonstrated that NH4+ and K+ were retarded (Rf =3.5) relative to a nonreactive tracer (Br-). Sorption of dissolved NH4+ was accompanied by concomitant release of calcium (Ca2+), magnesium (Mg2+), and sodium (Na+) from aquifer sediments, suggesting involvement of cation exchange. In contrast, nitrate (NO3-) was not retarded and cleanly separated from NH4+ and K+ in the small-scale tracer tests. This study demonstrates that transport of NH4+ and K+ through a sand and gravel aquifer can be markedly affected by cation-exchange processes even at a clay content less than 0.1%.

  2. Fluorinated Aromatic Amino Acids Distinguish Cation-π Interactions from Membrane Insertion.

    PubMed

    He, Tao; Gershenson, Anne; Eyles, Stephen J; Lee, Yan-Jiun; Liu, Wenshe R; Wang, Jiangyun; Gao, Jianmin; Roberts, Mary F

    2015-07-31

    Cation-π interactions, where protein aromatic residues supply π systems while a positive-charged portion of phospholipid head groups are the cations, have been suggested as important binding modes for peripheral membrane proteins. However, aromatic amino acids can also insert into membranes and hydrophobically interact with lipid tails. Heretofore there has been no facile way to differentiate these two types of interactions. We show that specific incorporation of fluorinated amino acids into proteins can experimentally distinguish cation-π interactions from membrane insertion of the aromatic side chains. Fluorinated aromatic amino acids destabilize the cation-π interactions by altering electrostatics of the aromatic ring, whereas their increased hydrophobicity enhances membrane insertion. Incorporation of pentafluorophenylalanine or difluorotyrosine into a Staphylococcus aureus phosphatidylinositol-specific phospholipase C variant engineered to contain a specific PC-binding site demonstrates the effectiveness of this methodology. Applying this methodology to the plethora of tyrosine residues in Bacillus thuringiensis phosphatidylinositol-specific phospholipase C definitively identifies those involved in cation-π interactions with phosphatidylcholine. This powerful method can easily be used to determine the roles of aromatic residues in other peripheral membrane proteins and in integral membrane proteins. PMID:26092728

  3. Fluorinated Aromatic Amino Acids Distinguish Cation-π Interactions from Membrane Insertion*

    PubMed Central

    He, Tao; Gershenson, Anne; Eyles, Stephen J.; Lee, Yan-Jiun; Liu, Wenshe R.; Wang, Jiangyun; Gao, Jianmin; Roberts, Mary F.

    2015-01-01

    Cation-π interactions, where protein aromatic residues supply π systems while a positive-charged portion of phospholipid head groups are the cations, have been suggested as important binding modes for peripheral membrane proteins. However, aromatic amino acids can also insert into membranes and hydrophobically interact with lipid tails. Heretofore there has been no facile way to differentiate these two types of interactions. We show that specific incorporation of fluorinated amino acids into proteins can experimentally distinguish cation-π interactions from membrane insertion of the aromatic side chains. Fluorinated aromatic amino acids destabilize the cation-π interactions by altering electrostatics of the aromatic ring, whereas their increased hydrophobicity enhances membrane insertion. Incorporation of pentafluorophenylalanine or difluorotyrosine into a Staphylococcus aureus phosphatidylinositol-specific phospholipase C variant engineered to contain a specific PC-binding site demonstrates the effectiveness of this methodology. Applying this methodology to the plethora of tyrosine residues in Bacillus thuringiensis phosphatidylinositol-specific phospholipase C definitively identifies those involved in cation-π interactions with phosphatidylcholine. This powerful method can easily be used to determine the roles of aromatic residues in other peripheral membrane proteins and in integral membrane proteins. PMID:26092728

  4. Isolation and separation of transplutonium elements from other actinides on ion exchange resins from aqueous and aqueous ethanol solutions of sulfuric acid

    SciTech Connect

    Guseva, L.I.; Tikhomirova, G.S.; Stepushkina, V.V.

    1987-11-01

    The behavior of Am, Cm, Bk, Cf, Es, and other actinides, as well as Zr, on an anion exchange resin and a cation exchange resin in aqueous and aqueous alcohol solutions of sulfuric acid was investigated as a function of the concentration of various components of the solution. It was found that the presence of alcohol in sulfuric acid solutions leads to an increase in the distribution coefficients both on cation exchange resins and on anion exchange resins. The possibility of using ion exchange resins for the concentration and separation of transplutonium elements from U, Np, Pu, Zr, and other elements that form strong complexes with sulfate ions in a wide range of sulfuric acid concentrations was demonstrated.

  5. Ion-exchange chromatographic analysis of peroxynitric acid.

    PubMed

    Nakashima, Yoichi; Ikawa, Satoshi; Tani, Atsushi; Kitano, Katsuhisa

    2016-01-29

    Ion-exchange chromatographic analysis of peroxynitric acid (O2NOOH) was performed by combining an acidic eluate with an UV-vis detector and immersing the separation column in an ice-water bath. The decomposition behavior of peroxynitric acid in the solution was also studied using this system. The fraction for the peroxynitric acid peak was collected. Ion-exchange chromatographic analysis of this fraction, after standing at room temperature for 24h, showed that the decomposition products were mainly nitrate ions with a very small amount of nitrous acid. The peroxynitric acid peak area correlated perfectly with the total amount of decomposition products. The ion-exchange chromatographic isolation allowed us to evaluate the molar extinction coefficient of peroxynitric acid precisely in a wider wavelength range than previous reports. The value decreases monotonically from 1729±26M(-1)cm(-1) at 200nm to 12.0±0.5M(-1)cm(-1) at 290nm.

  6. Isolation of carboxyl-termini and blocked amino-termini of viral proteins by high-performance cation-exchange chromatography.

    PubMed

    Gorman, J J; Shiell, B J

    1993-08-27

    The strong cation-exchanger, PolySulfoethyl Aspartamide, has been assessed as a medium for isolation of carboxyl-terminal and blocked amino-terminal peptides from tryptic digests of small quantities of viral proteins. Peptides with a single positive charge, the blocked amino-terminal peptides of ovalbumin and the Newcastle disease virus (NDV) matrix protein and carboxyl-terminal peptides of ovalbumin and the NDV nucleocapsid protein, eluted in early ion-exchange fractions and were readily isolated in homogeneous form by subsequent reversed-phase HPLC. Some early ion-exchange fractions also contained singly charged peptides derived by "chymotryptic-like" cleavage, whilst other peptides eluted in these fractions due to their highly acidic character. Terminal sequences with additional basic residues were isolated from later eluting ion-exchange fractions. Peptides with this property included the blocked amino-terminus of the NDV nucleocapsid protein and a portion of the carboxyl-terminus of the NDV matrix protein. Hitherto undescribed polymorphism in the amino-terminal region of ovalbumin was revealed in this study. Truncated peptides from the carboxyl-terminus of the NDV matrix protein were also detected. The presence of these peptides could be a reflection of carboxyl-terminal processing of the matrix protein. The strategy described herein should be of general utility for selective microisolation of carboxyl-terminal peptides and blocked amino-terminal peptides from tryptic digests of proteins. PMID:8408428

  7. Cation-Anion Interactions within the Nucleic Acid Ion Atmosphere Revealed by Ion Counting.

    PubMed

    Gebala, Magdalena; Giambaşu, George M; Lipfert, Jan; Bisaria, Namita; Bonilla, Steve; Li, Guangchao; York, Darrin M; Herschlag, Daniel

    2015-11-25

    The ion atmosphere is a critical structural, dynamic, and energetic component of nucleic acids that profoundly affects their interactions with proteins and ligands. Experimental methods that "count" the number of ions thermodynamically associated with the ion atmosphere allow dissection of energetic properties of the ion atmosphere, and thus provide direct comparison to theoretical results. Previous experiments have focused primarily on the cations that are attracted to nucleic acid polyanions, but have also showed that anions are excluded from the ion atmosphere. Herein, we have systematically explored the properties of anion exclusion, testing the zeroth-order model that anions of different identity are equally excluded due to electrostatic repulsion. Using a series of monovalent salts, we find, surprisingly, that the extent of anion exclusion and cation inclusion significantly depends on salt identity. The differences are prominent at higher concentrations and mirror trends in mean activity coefficients of the electrolyte solutions. Salts with lower activity coefficients exhibit greater accumulation of both cations and anions within the ion atmosphere, strongly suggesting that cation-anion correlation effects are present in the ion atmosphere and need to be accounted for to understand electrostatic interactions of nucleic acids. To test whether the effects of cation-anion correlations extend to nucleic acid kinetics and thermodynamics, we followed the folding of P4-P6, a domain of the Tetrahymena group I ribozyme, via single-molecule fluorescence resonance energy transfer in solutions with different salts. Solutions of identical concentration but lower activity gave slower and less favorable folding. Our results reveal hitherto unknown properties of the ion atmosphere and suggest possible roles of oriented ion pairs or anion-bridged cations in the ion atmosphere for electrolyte solutions of salts with reduced activity. Consideration of these new results leads to

  8. Multicenter bond index analysis of influence of metal cations on the aromaticity of aromatic amino acids: Phenylalanine and tyrosine

    NASA Astrophysics Data System (ADS)

    Pakiari, A. H.; Farrokhnia, M.; Azami, S. M.

    2008-05-01

    In order to provide insight into the influence of metal cations on the aromaticity of amino acids, evaluation of six-center delocalization indices is accomplished in the context of quantum theory of atoms in molecules (QTAIM). Aromaticity of two amino acids, phenylalanine and tyrosine, is investigated as typical amino acids containing aromatic ring in their isolated state and complexed by some metal cations. The results showed that the metal cations affect the most important three connectivities differently. Also, it is shown that the existence of metal cations can increase two-center delocalization in certain parts of the aromatic rings.

  9. THE ROLE OF SELECTED CATIONS IN THE FORMATION OF PSEUDOMICELLES IN AQUEOUS HUMIC ACID (R822832)

    EPA Science Inventory

    The fluorescence intensity enhancement of a pyrene probe in aqueous humic acid solutions was assessed in terms of added lanthanide and thorium cations. Among the trivalent ions it was found that size played a role, with the small Lu3+ ion producing the greatest increase in pyrene...

  10. Organo-Lewis acid as cocatalyst for cationic homogeneous Ziegler-Natta olefin polymerizations

    DOEpatents

    Marks, Tobin J.; Chen, You-Xian

    2002-01-01

    Organo-Lewis acids of the formula BR'R".sub.2 wherein B is boron, R' is fluorinated biphenyl, and R" is a fluorinated phenyl, fluorinated biphenyl, or fluorinated polycyclic fused ring group, and cationic metallocene complexes formed therewith. Such complexes are useful as polymerization catalysts.

  11. Organo-Lewis acid as cocatalyst for cationic homogeneous Ziegler-Natta olefin polymerizations

    DOEpatents

    Marks, Tobin J.; Chen, You-Xian

    2001-01-01

    Organo-Lewis acids of the formula BR'R".sub.2 wherein B is boron, R' is fluorinated biphenyl, and R" is a fluorinated phenyl, fluorinated biphenyl, or fluorinated polycyclic fused ring group, and cationic metallocene complexes formed therewith. Such complexes are useful as polymerization catalysts.

  12. Use of zirconium(IV) arsenophosphate columns for cation exchange separation of metal ions interfering in the spectrophotometric determination of uranium with sodium diethyl dithiocarbamate

    SciTech Connect

    Varshney, K.G.; Agrawal, S.; Anwar, S.; Varshney, K.

    1985-01-01

    A simple cation exchange method has been developed for the quantitative separation of uranium from some metal ions which generally interfere in its spectrophotometric determination using sodium diethyl dithiocarbamate as a reagent. The method requires only a single bed operation and enables a satisfactory (Error + or - separation of uranium (UO/sub 2/ (II)) up to 1080 ..mu..g from ten metal ions on a 2 g column of zirconium (IV) arsenophosphate cation exchanger in H(I) form.

  13. Cu3-xP Nanocrystals as a Material Platform for Near-Infrared Plasmonics and Cation Exchange Reactions

    PubMed Central

    2015-01-01

    Synthesis approaches to colloidal Cu3P nanocrystals (NCs) have been recently developed, and their optical absorption features in the near-infrared (NIR) have been interpreted as arising from a localized surface plasmon resonance (LSPR). Our pump–probe measurements on platelet-shaped Cu3-xP NCs corroborate the plasmonic character of this absorption. In accordance with studies on crystal structure analysis of Cu3P dating back to the 1970s, our density functional calculations indicate that this material is substoichiometric in copper, since the energy of formation of Cu vacancies in certain crystallographic sites is negative, that is, they are thermodynamically favored. Also, thermoelectric measurements point to a p-type behavior of the majority carriers from films of Cu3-xP NCs. It is likely that both the LSPR and the p-type character of our Cu3-xP NCs arise from the presence of a large number of Cu vacancies in such NCs. Motivated by the presence of Cu vacancies that facilitate the ion diffusion, we have additionally exploited Cu3-xP NCs as a starting material on which to probe cation exchange reactions. We demonstrate here that Cu3-xP NCs can be easily cation-exchanged to hexagonal wurtzite InP NCs, with preservation of the anion framework (the anion framework in Cu3-xP is very close to that of wurtzite InP). Intermediate steps in this reaction are represented by Cu3-xP/InP heterostructures, as a consequence of the fact that the exchange between Cu+ and In3+ ions starts from the peripheral corners of each NC and gradually evolves toward the center. The feasibility of this transformation makes Cu3-xP NCs an interesting material platform from which to access other metal phosphides by cation exchange. PMID:25960605

  14. Comparison between methods using copper, lanthanum, and colorimetry for the determination of the cation exchange capacity of plant cell walls.

    PubMed

    Wehr, J Bernhard; Blamey, F Pax C; Menzies, Neal W

    2010-04-28

    The determination of the cation exchange capacity (CEC) of plant cell walls is important for many physiological studies. We describe the determination of cell wall CEC by cation binding, using either copper (Cu) or lanthanum (La) ions, and by colorimetry. Both cations are strongly bound by cell walls, permitting fast and reproducible determinations of the CEC of small samples. However, the dye binding methods using two cationic dyes, Methylene Blue and Toluidine Blue, overestimated the CEC several-fold. Column and centrifugation methods are proposed for CEC determination by Cu or La binding; both provide similar results. The column method involves packing plant material (2-10 mg dry mass) in a chromatography column (10 mL) and percolating with 20 bed volumes of 1 mM La or Cu solution, followed by washing with deionized water. The centrifugation method uses a suspension of plant material (1-2 mL) that is centrifuged, and the pellet is mixed three times with 10 pellet volumes of 1 mM La or Cu solution followed by centrifugation and final washing with deionized water. In both methods the amount of La or Cu bound to the material was determined by spectroscopic methods.

  15. Cationic poly(lactic-co-glycolic acid) iron oxide microspheres for nucleic acid detection

    NASA Astrophysics Data System (ADS)

    Pandey, Chandra Mouli; Sharma, Aditya; Sumana, Gajjala; Tiwari, Ida; Malhotra, Bansi Dhar

    2013-04-01

    Herein, we envisage the possibility of preparing stable cationic poly(lactic-co-glycolic acid) (PLGA) microspheres encapsulating the iron oxide nanoparticles (IONPs; 8-12 nm). The IONPs are incorporated into PLGA in organic phase followed by microsphere formation and chitosan coating in aqueous medium via nano-emulsion technique. The average size of the microspheres, as determined by dynamic light scattering are about 310 nm, while the zeta potential for the composite remains near 35 mV at pH 4.0. These microspheres are electrophoretically deposited onto indium tin oxide (ITO)-coated glass substrate used as cathode and parallel platinum plate as the counter electrode. This platform is utilized to fabricate a DNA biosensor, by immobilizing a probe sequence specific to Escherichia coli. The bioelectrode shows a surface-controlled electrode reaction with the electron transfer coefficient (α) of 0.64 and charge transfer rate constant (ks) of 61.73 s-1. Under the optimal conditions, this biosensor shows a detection limit of 8.7 × 10-14 M and is found to retain about 81% of the initial activity after 9 cycles of use.Herein, we envisage the possibility of preparing stable cationic poly(lactic-co-glycolic acid) (PLGA) microspheres encapsulating the iron oxide nanoparticles (IONPs; 8-12 nm). The IONPs are incorporated into PLGA in organic phase followed by microsphere formation and chitosan coating in aqueous medium via nano-emulsion technique. The average size of the microspheres, as determined by dynamic light scattering are about 310 nm, while the zeta potential for the composite remains near 35 mV at pH 4.0. These microspheres are electrophoretically deposited onto indium tin oxide (ITO)-coated glass substrate used as cathode and parallel platinum plate as the counter electrode. This platform is utilized to fabricate a DNA biosensor, by immobilizing a probe sequence specific to Escherichia coli. The bioelectrode shows a surface-controlled electrode reaction with the

  16. Conformations of cationized linear oligosaccharides revealed by FTMS combined with in-ESI H/D exchange.

    PubMed

    Kostyukevich, Yury; Kononikhin, Alexey; Popov, Igor; Nikolaev, Eugene

    2015-10-01

    Previously (Kostyukevich et al. Anal Chem 2014, 86, 2595), we have reported that oligosaccharides anions are produced in the electrospray in two different conformations, which differ by the rate of gas phase hydrogen/deuterium (H/D) exchange reaction. In the present paper, we apply the in-electrospray ionization (ESI) source H/D exchange approach for the investigation of the oligosaccharides cations formed by attaching of metal ions (Na, K) to the molecule. It was observed that the formation of different conformers can be manipulated by varying the temperature of the desolvating capillary of the ESI interphase. Separation of the conformers was performed using gas phase H/D approach. Because the conformers have different rates of the H/D exchange reaction, the deuterium distribution spectrum becomes bimodal. It was found that the conformation corresponding to the slow H/D exchange rate dominates in the spectrum when the capillary temperature is low (~200 °C), and the conformation corresponding to the fast H/D exchange rate dominates at high (~400 °C) temperatures. In the intermediate temperature region, two conformers are present simultaneously. It was also observed that large oligosaccharide requires higher temperature for the formation of another conformer. It was found that the presence of the conformers considerably depends on the solvent used for ESI and the pH. We have compared these results with the previously performed in-ESI source H/D exchange experiments with peptides and proteins.

  17. Elucidating the higher stability of vanadium(V) cations in mixed acid based redox flow battery electrolytes

    NASA Astrophysics Data System (ADS)

    Vijayakumar, M.; Wang, Wei; Nie, Zimin; Sprenkle, Vincent; Hu, JianZhi

    2013-11-01

    The vanadium(V) cation structures in mixed acid based electrolyte solution were analyzed by density functional theory (DFT) based computational modeling and 51V and 35Cl nuclear magnetic resonance (NMR) spectroscopy. The vanadium(V) cation exists as di-nuclear [V2O3Cl2·6H2O]2+ compound at higher vanadium concentrations (≥1.75 M). In particular, at high temperatures (>295 K) this di-nuclear compound undergoes ligand exchange process with nearby solvent chlorine molecule and forms chlorine bonded [V2O3Cl·6H2O]2+ compound. This chlorine bonded [V2O3Cl2·6H2O]2+ compound might be resistant to the de-protonation reaction which is the initial step in the precipitation reaction in vanadium based electrolyte solutions. The combined theoretical and experimental approach reveals that formation of chlorine bonded [V2O3Cl2·6H2O]2+ compound might be central to the observed higher thermal stability of mixed acid based vanadium(V) electrolyte solutions.

  18. Neopentane and solid acids: direct hydron exchange before cracking.

    PubMed

    Walspurger, Stéphane; Sun, Yinyong; Souna Sido, Abdelkarim Sani; Sommer, Jean

    2006-09-21

    The hydrogen/deuterium exchange reaction of 2,2-dimethylpropane (neopentane) over D(2)O-exchanged zeolites (MOR, FAU, BEA, MFI) using a batch recirculation reactor was studied by means of gas chromatography coupled with mass spectrometer. In the temperature range 473-573 K, H/D exchange proceeds without side reaction such as cracking at short contact times. Indeed the C-H bond has appeared favorably involved in the activation of neopentane compared to the less accessible C-C bond. The transition state allowing hydron exchange is most likely a carbonium species (pentacoordinated carbon) as in the case of the H/D exchange between methane and solid acid. The activation energies of the H/D exchange between neopentane and zeolites are the same for all zeolites indicating a common carbonium ion type transition state. On the basis of previous results in the case of the exchange between methane and liquid superacids, the deuterium exchange rates in neopentane were tentatively related to the acidity of the solids. However the order of activity MOR > MFI > BEA > FAU seems to be related to the size of the pores, which may suggest the involvement of a confinement effect in the zeolites cavities. Moreover we found that H/D exchange takes also place between neopentane and deuterated sulfated zirconia (SZ) emphasizing its strong acidity.

  19. Purification Or Organic Acids Using Anion Exchange Chromatography.

    DOEpatents

    Ponnampalam; Elankovan

    2001-09-04

    Disclosed is a cost-effective method for purifying and acidifying carboxylic acids, including organic acids and amino acids. The method involves removing impurities by allowing the anionic form of the carboxylic acid to bind to an anion exchange column and washing the column. The carboxylic anion is displaced as carboxylic acid by washing the resin with a strong inorganic anion. This method is effective in removing organic carboxylic acids and amino acids from a variety of industrial sources, including fermentation broths, hydrolysates, and waste streams.

  20. The investigation on cationic exchange capacity of zeolites: the use as selective ion trappers in the electrokinetic soil technique.

    PubMed

    Ursini, Ornella; Lilla, Edo; Montanari, Roberta

    2006-09-21

    The cation exchange capacity (CEC) of porous zeolites allows to adsorb in the framework cavities the cations as pollutant heavy metal ions. We investigate the CEC behaviour of different zeolites in different experimental conditions; in solution where the ion's mobility is spontaneous and free and in the electrokinetic system where the ion's mobility is driven by the electric field. The aim of this study is to investigate if the CEC is an useful property to create a special interface region of zeolites, that if placed in the electrokinetic cell, just before the cathode, could allow to capture and concentrate the heavy metallic ions, during their migrating process. The zeolite 13X investigated in the electrokinetic proofs, retains a good high ions adsorption, even if quite smaller than the relevant free solution condition and well acts as confined trap for the heavy metal ions. In fact no trace of metallic deposition are present on the electrode's surface. PMID:16716501

  1. Spectral and Acid-Base Properties of Hydroxyflavones in Micellar Solutions of Cationic Surfactants

    NASA Astrophysics Data System (ADS)

    Lipkovska, N. A.; Barvinchenko, V. N.; Fedyanina, T. V.; Rugal', A. A.

    2014-09-01

    It has been shown that the spectral characteristics (intensity, position of the absorption band) and the acid-base properties in a series of structurally similar hydroxyflavones depend on the concentration of the cationic surfactants miramistin and decamethoxin in aqueous solutions, and the extent of their changes is more pronounced for hydrophobic quercetin than for hydrophilic rutin. For the first time, we have determined the apparent dissociation constants of quercetin and rutin in solutions of these cationic surfactants (pKa1) over a broad concentration range and we have established that they decrease in the series water-decamethoxin-miramistin.

  2. Acidity-Activated Shielding Strategies of Cationic Gene Delivery for Cancer Therapy.

    PubMed

    Xia, Jialiang; Feng, Zongcai; Yang, Hongyan; Lin, Sanqing; Han, Bing

    2016-01-01

    Cationic gene vectors increased attractive for gene therapy. However, unstable systemic circulation due to the interaction of gene delivery system with blood cells limited the further application. Therefore, pH sensitive shielding systems were exploited, by which, the positive surface charge density of polyplexes was reduced, circulation time was improved and pH-triggered targeting delivery was promised. This mini review mainly focuses on the development of solid tumors pH environment activated shielding systems for cationic gene vectors. This shielding strategy shows great potential for enhancing efficient gene transporting and achieving better therapeutic effects in acidic tumor treatment.

  3. Acid rain and acidification in China: the importance of base cation deposition.

    PubMed

    Larssen, T; Carmichael, G R

    2000-10-01

    Acid deposition has been recognized as a serious environmental problem in China. Most acid deposition studies have focused on sulfur deposition and the pH of precipitation. However, as high concentration of alkaline dust is an important feature of the atmosphere in large parts of China, base cation deposition must be taken into account when discussing possible effects on soils and vegetation from acid deposition. We estimate the deposition of sulfur as well as calcium, i.e. the dominating anion and cation, on a regional scale in China using data both from measurements and modeling. The ratio of sulfur/calcium in deposition is then used as an indicator for identifying areas where deposition acidity exceeds alkalinity, and where soils may be at risk to acidification. The dynamic soil acidification model MAGIC is applied with data from two sites receiving high deposition loads in southwest China. The model predictions indicate that considerable soil acidification has been going on for the last decades due to acid deposition inputs. Effects on the spatial distribution of acidic deposition in China, using different future deposition scenarios, are illustrated. As the size of the anthropogenic fraction of the base cation deposition is unknown, different possible future trends in calcium deposition were used. Soil response, according to the model, using different combinations of sulfur and calcium deposition scenarios is shown. Applying the most strict measures to reduce sulfur emission will almost eliminate the acid deposition problem; however, such a scenario is not economically feasible in the short term. A strict, but possibly realistic, future scenario for sulfur may be enough to keep the situation at the present level, assuming only moderate reductions in calcium deposition. With large decreases in base cation deposition, increased soil acidification can be expected even with considerable sulfur emission reductions.

  4. Consistent effects of canopy vs. understory nitrogen addition on the soil exchangeable cations and microbial community in two contrasting forests.

    PubMed

    Shi, Leilei; Zhang, Hongzhi; Liu, Tao; Zhang, Weixin; Shao, Yuanhu; Ha, Denglong; Li, Yuanqiu; Zhang, Chuangmao; Cai, Xi-an; Rao, Xingquan; Lin, Yongbiao; Zhou, Lixia; Zhao, Ping; Ye, Qing; Zou, Xiaoming; Fu, Shenglei

    2016-05-15

    Anthropogenic N deposition has been well documented to cause substantial impacts on the chemical and biological properties of forest soils. In most studies, however, atmospheric N deposition has been simulated by directly adding N to the forest floor. Such studies thus ignored the potentially significant effect of some key processes occurring in forest canopy (i.e., nitrogen retention) and may therefore have incorrectly assessed the effects of N deposition on soils. Here, we conducted an experiment that included both understory addition of N (UAN) and canopy addition of N (CAN) in two contrasting forests (temperate deciduous forest vs. subtropical evergreen forest). The goal was to determine whether the effects on soil exchangeable cations and microbial biomass differed between CAN and UAN. We found that N addition reduced pH, BS (base saturation) and exchangeable Ca and increased exchangeable Al significantly only at the temperate JGS site, and reduced the biomass of most soil microbial groups only at the subtropical SMT site. Except for soil exchangeable Mn, however, effects on soil chemical properties and soil microbial community did not significantly differ between CAN and UAN. Although biotic and abiotic soil characteristics differ significantly and the responses of both soil exchangeable cations and microbial biomass were different between the two study sites, we found no significant interactive effects between study site and N treatment approach on almost all soil properties involved in this study. In addition, N addition rate (25 vs. 50 kg N ha(-1) yr(-1)) did not show different effects on soil properties under both N addition approaches. These findings did not support previous prediction which expected that, by bypassing canopy effects (i.e., canopy retention and foliage fertilization), understory addition of N would overestimate the effects of N deposition on forest soil properties, at least for short time scale.

  5. Consistent effects of canopy vs. understory nitrogen addition on the soil exchangeable cations and microbial community in two contrasting forests.

    PubMed

    Shi, Leilei; Zhang, Hongzhi; Liu, Tao; Zhang, Weixin; Shao, Yuanhu; Ha, Denglong; Li, Yuanqiu; Zhang, Chuangmao; Cai, Xi-an; Rao, Xingquan; Lin, Yongbiao; Zhou, Lixia; Zhao, Ping; Ye, Qing; Zou, Xiaoming; Fu, Shenglei

    2016-05-15

    Anthropogenic N deposition has been well documented to cause substantial impacts on the chemical and biological properties of forest soils. In most studies, however, atmospheric N deposition has been simulated by directly adding N to the forest floor. Such studies thus ignored the potentially significant effect of some key processes occurring in forest canopy (i.e., nitrogen retention) and may therefore have incorrectly assessed the effects of N deposition on soils. Here, we conducted an experiment that included both understory addition of N (UAN) and canopy addition of N (CAN) in two contrasting forests (temperate deciduous forest vs. subtropical evergreen forest). The goal was to determine whether the effects on soil exchangeable cations and microbial biomass differed between CAN and UAN. We found that N addition reduced pH, BS (base saturation) and exchangeable Ca and increased exchangeable Al significantly only at the temperate JGS site, and reduced the biomass of most soil microbial groups only at the subtropical SMT site. Except for soil exchangeable Mn, however, effects on soil chemical properties and soil microbial community did not significantly differ between CAN and UAN. Although biotic and abiotic soil characteristics differ significantly and the responses of both soil exchangeable cations and microbial biomass were different between the two study sites, we found no significant interactive effects between study site and N treatment approach on almost all soil properties involved in this study. In addition, N addition rate (25 vs. 50 kg N ha(-1) yr(-1)) did not show different effects on soil properties under both N addition approaches. These findings did not support previous prediction which expected that, by bypassing canopy effects (i.e., canopy retention and foliage fertilization), understory addition of N would overestimate the effects of N deposition on forest soil properties, at least for short time scale. PMID:26930308

  6. Synthesis, characterization and ion-exchange properties of a new and novel 'organic-inorganic' hybrid cation-exchanger: Nylon-6,6, Zr(IV) phosphate.

    PubMed

    Inamuddin; Khan, Shakeel Ahmad; Siddiqui, Weqar Ahmad; Khan, Asif Ali

    2007-02-15

    Organic-inorganic hybrid materials enable the integration of useful organic and inorganic characteristics within a single molecular-scale composite. Unique ion-exchange properties of these types of materials have been observed, and many others can be envisioned for this promising class of materials. In this paper, we describe the ion-exchange and physico-chemical properties of one family of self-assembling organic-inorganic hybrid based on nylon-6,6, framework with Zr(IV) phosphate an inorganic ion-exchanger. The physico-chemical properties of this hybrid material were determined using atomic absorption spectrophotometry (AAS), CHN elemental analysis, ICP-MS, UV-vis spectrophotometry, FTIR, TGA-DTA and scanning electron microscope (SEM) studies. Ion-exchange capacity (IEC), thermal stability and distribution behavior, etc. were also carried out to understand the cation-exchange behavior of the material. On the basis of distribution studies, the material was found to be highly selective for Hg(II), a highly toxic environmental pollutant. Its selectivity was examined by achieving some important binary separations like Hg(II)-Mg(II), Hg(II)-Zn(II), Hg(II)-Fe(III), Hg(II)-Bi(III), etc. Thus, the relatively new field of "organic-inorganic" hybrids offers a variety of exciting technological opportunities to decrease the environmental pollution.

  7. Inhibition of iron corrosion in 0.5 M sulphuric acid by metal cations

    NASA Astrophysics Data System (ADS)

    Sathiyanarayanan, S.; Jeyaprabha, C.; Muralidharan, S.; Venkatachari, G.

    2006-09-01

    Corrosion inhibitors are widely used in acid solutions during pickling and descaling. Mostly organic compounds containing N, O, and S groups are employed as inhibitors. In this study, the inhibition performance of metal cations such as Zn 2+, Mn 2+ and Ce 4+ ions in the concentration range 1-10 × 10 -3 M has been found out. The corrosion behaviour of iron in 0.5 M H 2SO 4 in the presence of metal cations is studied using polarization and impedance methods. It is found that the addition of these metal cations inhibits the corrosion markedly. The inhibition effect is in the following order Ce 4+ ≫ Mn 2+ > Zn 2+.

  8. The role of metal ions in chemical evolution - Polymerization of alanine and glycine in a cation-exchanged clay environment

    NASA Technical Reports Server (NTRS)

    Lawless, J. G.; Levi, N.

    1979-01-01

    The effect of the exchangeable cation on the condensation of glycine and alanine was investigated using a series of homoionic bentonites. A cycling procedure of drying, warming and wetting was employed. Peptide bond formation was observed, and the effectiveness of metal ions to catalyze the condensation was Cu(2+) greater than Ni(2) approximately equals Zn(2+) greater than Na(+). Glycine showed 6% of the monomer incorporated into oligomers with the largest detected being the pentamer. Alanine showed less peptide bond formation (a maximum of 2%) and only the dimer was observed.

  9. Swelling and electro-osmotic properties of cation-exchange membranes with different structures in methanol-water media

    NASA Astrophysics Data System (ADS)

    Barragán, V. M.; Villaluenga, J. P. G.; Godino, M. P.; Izquierdo-Gil, M. A.; Ruiz-Bauzá, C.; Seoane, B.

    Electro-osmosis experiments through three cation-exchange membranes with different morphology and similar electric properties have been performed using methanol-water solutions under different experimental conditions. The influence on the electro-osmotic transport of the percentage of methanol on solvent with two different electrolytes, NaCl and LiCl, has been studied. The experimental results show that the presence of methanol in the solutions affects strongly the electro-osmotic flow, and this influence is different depending on the membrane morphology. Correlations among electro-osmotic permeability, swelling behavior, and cell resistance are studied for these membrane systems at different percentages of methanol in solvent.

  10. Removal of cationic dyes by poly(acrylamide-co-acrylic acid) hydrogels in aqueous solutions

    NASA Astrophysics Data System (ADS)

    Şolpan, Dilek; Duran, Sibel; Torun, Murat

    2008-04-01

    Poly(acrylamide-co-acrylic acid (poly(AAm-co-AAc)) hydrogels prepared by irradiating with γ-radiation were used in experiments on swelling, diffusion, and uptake of some cationic dyes such as Safranine-O (SO) and Magenta (M). Poly(AAm-co-AAc) hydrogels irradiated at 8.0 kGy have been used for swelling and diffusion studies in water and cationic dye solutions. The maximum swellings in water, and SO, and M solutions observed are 2700%, 3500%, and 4000%, respectively. Diffusions of water and cationic dyes within hydrogels have been found to be non-Fickian in character. Adsorption of the cationic dyes onto poly(AAm-co-AAc) hydrogels is studied by the batch adsorption technique. The adsorption type was found Langmuir type in the Giles classification system. The moles of adsorbed dye for SO and M per repeating unit in hydrogel (binding ratio, r) have been calculated as 3834×10 -6 and 1323×10 -6, respectively. These results show that poly(AAm-co-AAc) hydrogels can be used as adsorbent for water pollutants such as cationic dyes.

  11. Metal cation dependence of interactions with amino acids: bond dissociation energies of Rb(+) and Cs(+) to the acidic amino acids and their amide derivatives.

    PubMed

    Armentrout, P B; Yang, Bo; Rodgers, M T

    2014-04-24

    Metal cation-amino acid interactions are key components controlling the secondary structure and biological function of proteins, enzymes, and macromolecular complexes comprising these species. Determination of pairwise interactions of alkali metal cations with amino acids provides a thermodynamic vocabulary that begins to quantify these fundamental processes. In the present work, we expand a systematic study of such interactions by examining rubidium and cesium cations binding with the acidic amino acids (AA), aspartic acid (Asp) and glutamic acid (Glu), and their amide derivatives, asparagine (Asn) and glutamine (Gln). These eight complexes are formed using electrospray ionization and their bond dissociation energies (BDEs) are determined experimentally using threshold collision-induced dissociation with xenon in a guided ion beam tandem mass spectrometer. Analyses of the energy-dependent cross sections include consideration of unimolecular decay rates, internal energy of the reactant ions, and multiple ion-neutral collisions. Quantum chemical calculations are conducted at the B3LYP, MP2(full), and M06 levels of theory using def2-TZVPPD basis sets, with results showing reasonable agreement with experiment. At 0 and 298 K, most levels of theory predict that the ground-state conformers for M(+)(Asp) and M(+)(Asn) involve tridentate binding of the metal cation to the backbone carbonyl, amino, and side-chain carbonyl groups, although tridentate binding to the carboxylic acid group and side-chain carbonyl is competitive for M(+)(Asn). For the two longer side-chain amino acids, Glu and Gln, multiple structures are competitive. A comparison of these results to those for the smaller alkali cations, Na(+) and K(+), provides insight into the trends in binding energies associated with the molecular polarizability and dipole moment of the side chain. For all four metal cations, the BDEs are inversely correlated with the size of the metal cation and follow the order Asp < Glu

  12. Potential heat exchange fluids for use in sulfuric acid vaporizers

    NASA Technical Reports Server (NTRS)

    Lawson, D. D.; Petersen, G. R.

    1979-01-01

    A series of perhalocarbons are proposed as candidate heat exchange fluids for service in thermochemical cycles for hydrogen production that involve direct contact of the fluid with sulfuric acid and vaporization of the acid. The required chemical and physical criteria of the liquids are described and the results of some preliminary high temperature test data are presented.

  13. Diverse functions and molecular properties emerging for CAX Cation/H+ exchangers in plants

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Steep concentration gradients of many ions are actively maintained, with lower concentrations typically located in the cytosol, and higher concentrations in organelles and outside the cell. The vacuole is an important storage organelle for many ions. The concentration gradient of cations is establis...

  14. Recent progress in gene therapy to deliver nucleic acids with multivalent cationic vectors.

    PubMed

    Junquera, Elena; Aicart, Emilio

    2016-07-01

    Due to the potential use as transfecting agents of nucleic acids (DNA or RNA), multivalent cationic non-viral vectors have received special attention in the last decade. Much effort has been addressed to synthesize more efficient and biocompatible gene vectors able to transport nucleic acids into the cells without provoking an immune response. Among them, the mostly explored to compact and transfect nucleic acids are: (a) gemini and multivalent cationic lipids, mixed with a helper lipid, by forming lipoplexes; and (b) cationic polymers, polycations, and polyrotaxanes, by forming polyplexes. This review is focused on the progress and recent advances experimented in this area, mainly during the present decade, devoting special attention to the lipoplexes and polyplexes, as follows: (a) to its biophysical characterization (mainly electrostatics, structure, size and morphology) using a wide variety of experimental methods; and (b) to its biological activity (transfection efficacy and cytotoxicity) addressed to confirm the optimum formulations and viability of these complexes as very promising gene vectors of nucleic acids in nanomedicine.

  15. C-1s NEXAFS spectroscopy reveals chemical fractionation of humic acid by cation-induced coagulation

    SciTech Connect

    Christl,I.; Kretzschmar, R.

    2007-01-01

    The influence of cation-induced coagulation on the chemical composition of dissolved and coagulated fractions of humic acid was investigated in batch coagulation experiments for additions of aluminum at pH 4 and 5, iron at pH 4, and calcium and lead at pH 6. The partitioning of organic carbon and metals was determined by analyzing total organic carbon and total metal contents of the dissolved phase. Both the dissolved and the coagulated humic acid fractions were characterized using synchrotron scanning transmission X-ray microscopy (STXM) and C-1s near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. Intensities of {pi}* transitions of carboxyl carbon and {sigma}* transitions of alkyl, O-alkyl, and carboxyl carbon decreased with increasing metal concentration for the dissolved humic acid fractions. This decrease was accompanied by an increase of the respective intensities in the coagulated fraction as shown for lead. Intensities of aromatic and phenolic carbon were affected to a larger extent only by aluminum and iron additions. The changes observed in the C-1s NEXAFS spectra coincided with an increasing removal of organic carbon from the dissolved phase with increasing total metal concentrations. We conclude that humic acid was chemically fractionated by cation-induced coagulation, which preferentially removed functional groups involved in metal-cation binding from solution.

  16. Suitability of the methylene blue test for determination of cation exchange capacity of clay minerals related to ammonium acetate method

    NASA Astrophysics Data System (ADS)

    Milošević, Maja; Logar, Mihovil; Dojčinović, Biljana; Erić, Suzana

    2015-04-01

    Cation exchange capacity (CEC) represents one of the most important parameters of clay minerals which reflects their ability to exchange cations with liquid phases in near contact. Measurement of CEC is used for characterizing sample plasticity, adsorbing and swelling properties which later define their usage in industrial purposes. Several methods have been developed over the years for determination of layer charge, charge density, charge distribution, etc. and have been published in numerous papers (Czimerova et al., 2006; Yukselen and Kaya, 2008). The main goal of present study is comparison of suitability of more recent method - methylene blue test in regard to older method - ammonium acetate for determination of CEC. For this study, we selected one montmorillonite clay (Bogovina, Serbia) and two mainly kaolinite clays (Miličinica, Serbia). Chemicals used for CEC determinations were solution of methylene blue (MB)(14*10-6M/ml) and ammonium acetate (AA) solution (1M). The obtained results are showing generally lower values in case of MB method. The main difference is due to molecular aggregation of MB on the clay surface. AA method is highly sensitive to the presence of CaO. Release of Ca ion from the sample into the solution can limit the saturation of exchange sites by the ammonium ion. This is clearly visible in case of montmorillonite clay. Fe2+ and Mg ions are difficult to move by the ammonium ion because of their ion radius, but in case of MB molecule there is no such restriction in removing them from the exchange sites. MB solution, even in a low concentration (2*10-6M/ml), is showing preferable results in moving the ions from their positions which is already visible after adding a small quantity of solution (25cm3). Both MB-titration and MB-spot test yield similar results and are much simpler methods than AA and they also give other information such as specific surface area (external and internal) whereas AA method only provides information about

  17. Effects of multivalent cations on cell wall-associated acid phosphatase activity

    SciTech Connect

    Tu, S.I.; Brouillette, J.N.; Nagahashi, G.; Kumosinski, T.F.

    1988-09-01

    Primary cell walls, free from cytoplasmic contamination were prepared from corn (Zea mays L.) roots and potato (Solanum tuberosum) tubers. After EDTA treatment, the bound acid phosphatase activities were measured in the presence of various multivalent cations. Under the conditions of minimized Donnan effect and at pH 4.2, the bound enzyme activity of potato tuber cell walls (PCW) was stimulated by Cu/sup 2 +/, Mg/sup 2 +/, Za/sup 2 +/, and Mn/sup 2 +/; unaffected by Ba/sup 2 +/, Cd/sup 2 +/, and Pb/sup 2 +/; and inhibited by Al/sup 3 +/. The bound acid phosphatase of PCW was stimulated by a low concentration but inhibited by a higher concentration of Hg/sup 2 +/. On the other hand, in the case of corn root cells walls (CCW), only inhibition of the bound acid phosphatase by Al/sup 3 +/ and Hg/sup 2 +/ was observed. Kinetic analyses revealed that PCW acid phosphatase exhibited a negative cooperativity under all employed experimental conditions except in the presence of Mg/sup 2 +/. In contrast, CCW acid phosphatase showed no cooperative behavior. The presence of Ca/sup 2 +/ significantly reduced the effects of Hg/sup 2 +/ or Al/sup 3 +/, but not Mg/sup 2 +/, to the bound cell wall acid phosphatases. The salt solubilized (free) acid phosphatases from both PCW and CCW were not affected by the presence of tested cations except for Hg/sup 2 +/ or Al/sup 3 +/ which caused a Ca/sup 2 +/-insensitive inhibition of the enzymes. The induced stimulation or inhibition of bound acid phosphatases was quantitatively related to cation binding in the cell wall structure.

  18. Neomycin-loaded poly(styrene sulfonic acid-co-maleic acid) (PSSA-MA)/polyvinyl alcohol (PVA) ion exchange nanofibers for wound dressing materials.

    PubMed

    Nitanan, Todsapon; Akkaramongkolporn, Prasert; Rojanarata, Theerasak; Ngawhirunpat, Tanasait; Opanasopit, Praneet

    2013-05-01

    In this study, poly(styrene sulfonic acid-co-maleic acid) (PSSA-MA) blended with polyvinyl alcohol (PVA) was electrospun and then subjected to thermal crosslinking to produce PSSA-MA/PVA ion exchange nanofiber mats. The cationic drug neomycin (0.001, 0.01, and 0.1%, w/v) was loaded onto the cationic exchange fibers. The amount of neomycin loaded and released and the cytotoxicity of the fiber mats were analyzed. In vivo wound healing tests were also performed in Wistar rats. The results indicated that the diameters of the fibers were on the nanoscale (250 ± 21 nm). The ion exchange capacity (IEC) value and the percentage of water uptake were 2.19 ± 0.1 mequiv./g-dry fibers and 268 ± 15%, respectively. The loading capacity was increased upon increasing the neomycin concentration. An initial concentration of 0.1% (w/v) neomycin (F3) showed the highest loading capacity (65.7 mg/g-dry fibers). The neomycin-loaded nanofiber mats demonstrated satisfactory antibacterial activity against both Gram-positive and Gram-negative bacteria, and an in vivo wound healing test revealed that these mats performed better than gauze and blank nanofiber mats in decreasing acute wound size during the first week after tissue damage. In conclusion, the antibacterial neomycin-loaded PSSA-MA/PVA cationic exchange nanofiber mats have the potential for use as wound dressing materials.

  19. Toward Separating Alpha-lactalbumin and Beta-lactoglobulin Proteins from Whey through Cation-exchange Adsorption

    NASA Astrophysics Data System (ADS)

    El-Sayed, Mayyada; Chase, Howard

    2009-05-01

    This paper describes the cation-exchange adsorption of the two major whey proteins, alpha-lactalbumin (ALA) and beta-lactoglobulin (BLG) with the purpose of establishing a process for isolating them from cow's milk whey. The single- and two-component adsorption of 1.5 mg/ml ALA and 3 mg/ml BLG to the cation-exchanger SP Sepharose FF at 20° C using 0.1 M acetate buffer of pH 3.7 was studied. Langmuir isotherm parameters were determined for the pure proteins. In two-component systems, BLG breakthrough curve exhibited an overshoot phenomenon that gave evidence for the presence of a competitive adsorption between the two proteins. Complete separation occurred and it was possible to obtain each of the two proteins in a pure form. The process was then applied to a whey concentrate mixture where incomplete separation took place. However, BLG was produced with 95% purity and a recovery of 80%, while ALA showed an 84% recovery with low purity.

  20. [Enhanced Performance of Rolled Membrane Electrode Assembly by Adding Cation Exchange Resin to Anode in Microbial Fuel Cells].

    PubMed

    Mei, Zhuo; Zhang, Zhe; Wang, Xin

    2015-11-01

    The membrane electrode assembly (MEA) with an anode-membrane-cathode structure ban reduce the distance between anode and cathode to improve the power of microbial fuel cells (MFCs). Here in order to further promote the performance of MFCs, a novel MEA was constructed by rolling-press method without noble metal material, and the Ohmic resistance decreased to 3-5 Ω. The maximum power density was 446 mW x m(-2) when acetate was used as the substrate. Solid spheres (like polystyrene balls and glass microspheres) were added into anode to enhance the transportation of electrolyte to cathode, resulting in a 10% increase in power density by producing macropores on and in the anode during rolling process. Cation exchange resin was added to accelerate the transportation of proton through the anode so that the power density further increased to 543 mW x m(-2). Meanwhile, the stability of cell voltage and Coulomb efficiency of MFC were both enhanced after the addition of cation exchange resin. PMID:26911023

  1. [Enhanced Performance of Rolled Membrane Electrode Assembly by Adding Cation Exchange Resin to Anode in Microbial Fuel Cells].

    PubMed

    Mei, Zhuo; Zhang, Zhe; Wang, Xin

    2015-11-01

    The membrane electrode assembly (MEA) with an anode-membrane-cathode structure ban reduce the distance between anode and cathode to improve the power of microbial fuel cells (MFCs). Here in order to further promote the performance of MFCs, a novel MEA was constructed by rolling-press method without noble metal material, and the Ohmic resistance decreased to 3-5 Ω. The maximum power density was 446 mW x m(-2) when acetate was used as the substrate. Solid spheres (like polystyrene balls and glass microspheres) were added into anode to enhance the transportation of electrolyte to cathode, resulting in a 10% increase in power density by producing macropores on and in the anode during rolling process. Cation exchange resin was added to accelerate the transportation of proton through the anode so that the power density further increased to 543 mW x m(-2). Meanwhile, the stability of cell voltage and Coulomb efficiency of MFC were both enhanced after the addition of cation exchange resin.

  2. Comparison of gaseous oxidized Hg measured by KCl-coated denuders, and nylon and cation exchange membranes.

    PubMed

    Huang, Jiaoyan; Miller, Matthieu B; Weiss-Penzias, Peter; Gustin, Mae Sexauer

    2013-07-01

    The chemical compounds that make up gaseous oxidized mercury (GOM) in the atmosphere, and the reactions responsible for their formation, are not well understood. The limitations and uncertainties associated with the current method applied to measure these compounds, the KCl-coated denuder, are not known due to lack of calibration and testing. This study systematically compared the uptake of specific GOM compounds by KCl-coated denuders with that collected using nylon and cation exchange membranes in the laboratory and field. In addition, a new method for identifying different GOM compounds using thermal desorption is presented. Different GOM compounds (HgCl2, HgBr2, and HgO) were found to have different affinities for the denuder surface and the denuder underestimated each of these compounds. Membranes measured 1.3 to 3.7 times higher GOM than denuders in laboratory and field experiments. Cation exchange membranes had the highest collection efficiency. Thermodesorption profiles for the release of GOM compounds from the nylon membrane were different for HgO versus HgBr2 and HgCl2. Application of the new field method for collection and identification of GOM compounds demonstrated these vary as a function of location and time of year. Understanding the chemistry of GOM across space and time has important implications for those developing policy regarding this environmental contaminant. PMID:23651121

  3. Uncertainties of Gaseous Oxidized Mercury Measurements Using KCl-Coated Denuders, Cation-Exchange Membranes, and Nylon Membranes: Humidity Influences.

    PubMed

    Huang, Jiaoyan; Gustin, Mae Sexauer

    2015-05-19

    Quantifying the concentration of gaseous oxidized mercury (GOM) and identifying the chemical compounds in the atmosphere are important for developing accurate local, regional, and global biogeochemical cycles. The major hypothesis driving this work was that relative humidity affects collection of GOM on KCl-coated denuders and nylon membranes, both currently being applied to measure GOM. Using a laboratory manifold system and ambient air, GOM capture efficiency on 3 different collection surfaces, including KCl-coated denuders, nylon membranes, and cation-exchange membranes, was investigated at relative humidity ranging from 25 to 75%. Recovery of permeated HgBr2 on KCl-coated denuders declined by 4-60% during spikes of relative humidity (25 to 75%). When spikes were turned off GOM recoveries returned to 60 ± 19% of permeated levels. In some cases, KCl-coated denuders were gradually passivated over time after additional humidity was applied. In this study, GOM recovery on nylon membranes decreased with high humidity and ozone concentrations. However, additional humidity enhanced GOM recovery on cation-exchange membranes. In addition, reduction and oxidation of elemental mercury during experiments was observed. The findings in this study can help to explain field observations in previous studies.

  4. Analytical cation-exchange chromatography to assess the identity, purity, and N-terminal integrity of human lactoferrin.

    PubMed

    van Veen, Harrie A; Geerts, Marlieke E J; van Berkel, Patrick H C; Nuijens, Jan H

    2002-10-01

    Human lactoferrin (hLF) is an iron-binding glycoprotein involved in the innate host defense. The positively charged N-terminal domain of hLF mediates several of its activities by interacting with ligands such as bacterial lipopolysaccharide (LPS), specific receptors, and other proteins. This cationic domain is highly susceptible to limited proteolysis, which impacts on the affinity of hLF for the ligand. An analytical method, employing cation-exchange chromatography on Mono S, was developed to assess the N-terminal integrity of hLF preparations. The method, which separates N-terminally intact hLF from hLF species lacking two (Gly(1)-Arg(2)) or three (Gly(1)-Arg(2)-Arg(3)) residues, showed that 5-58% of total hLF in commercially obtained preparations was N-terminally degraded. The elution profile of hLF on Mono S unequivocally differed from lactoferrins from other species as well as homologous and other whey proteins. Analysis of fresh human whey samples revealed two variants of N-terminally intact hLF, but not limitedly proteolyzed hLF. Mono S chromatography of 2 out of 26 individual human whey samples showed a rare polymorphic hLF variant with three N-terminal arginines (Gly(1)-Arg(2)-Arg(3)-Arg(4)-Ser(5)-) instead of the usual variant with four N-terminal arginines (Gly(1)-Arg(2)-Arg(3)-Arg(4)-Arg(5)-Ser(6)-). In conclusion, Mono S cation-exchange chromatography appeared a robust method to assess the identity, purity, N-terminal integrity, and the presence of polymorphic and intact hLF variants. PMID:12381362

  5. Transporters for cationic amino acids in animal cells: discovery, structure, and function.

    PubMed

    Devés, R; Boyd, C A

    1998-04-01

    The structure and function of the four cationic amino acid transporters identified in animal cells are discussed. The systems differ in specificity, cation dependence, and physiological role. One of them, system y+, is selective for cationic amino acids, whereas the others (B[0,+], b[0,+], and y+ L) also accept neutral amino acids. In recent years, cDNA clones related to these activities have been isolated. Thus two families of proteins have been identified: 1) CAT or cationic amino acid transporters and 2) BAT or broad-scope transport proteins. In the CAT family, three genes encode for four different isoforms [CAT-1, CAT-2A, CAT-2(B) and CAT-3]; these are approximately 70-kDa proteins with multiple transmembrane segments (12-14), and despite their structural similarity, they differ in tissue distribution, kinetics, and regulatory properties. System y+ is the expression of the activity of CAT transporters. The BAT family includes two isoforms (rBAT and 4F2hc); these are 59- to 78-kDa proteins with one to four membrane-spanning segments, and it has been proposed that these proteins act as transport regulators. The expression of rBAT and 4F2hc induces system b[0,+] and system y+ L activity in Xenopus laevis oocytes, respectively. The roles of these transporters in nutrition, endocrinology, nitric oxide biology, and immunology, as well as in the genetic diseases cystinuria and lysinuric protein intolerance, are reviewed. Experimental strategies, which can be used in the kinetic characterization of coexpressed transporters, are also discussed.

  6. Formation and stability of N-heterocyclic carbenes in water: the carbon acid pKa of imidazolium cations in aqueous solution.

    PubMed

    Amyes, Tina L; Diver, Steven T; Richard, John P; Rivas, Felix M; Toth, Krisztina

    2004-04-01

    We report second-order rate constants kDO (M-1 s-1) for exchange for deuterium of the C(2)-proton of a series of simple imidazolium cations to give the corresponding singlet imidazol-2-yl carbenes in D2O at 25 degrees C and I = 1.0 (KCl). Evidence is presented that the reverse protonation of imidazol-2-yl carbenes by solvent water is limited by solvent reorganization and occurs with a rate constant of kHOH = kreorg = 10(11) s-1. The data were used to calculate reliable carbon acid pK(a)s for ionization of imidazolium cations at C(2) to give the corresponding singlet imidazol-2-yl carbenes in water: pKa = 23.8 for the imidazolium cation, pKa = 23.0 for the 1,3-dimethylimidazolium cation, pKa = 21.6 for the 1,3-dimethylbenzimidazolium cation, and pKa = 21.2 for the 1,3-bis-((S)-1-phenylethyl)benzimidazolium cation. The data also provide the thermodynamic driving force for a 1,2-hydrogen shift at a singlet carbene: K12 = 5 x 10(16) for rearrangement of the parent imidazol-2-yl carbene to give neutral imidazole in water at 298 K, which corresponds to a favorable Gibbs free energy change of 23 kcal/mol. We present a simple rationale for the observed substituent effects on the thermodynamic stability of N-heterocyclic carbenes relative to a variety of neutral and cationic derivatives that emphasizes the importance of the choice of reference reaction when assessing the stability of N-heterocyclic carbenes.

  7. [Nutrition, acid-base metabolism, cation-anion difference and total base balance in humans].

    PubMed

    Mioni, R; Sala, P; Mioni, G

    2008-01-01

    The relationship between dietary intake and acid-base metabolism has been investigated in the past by means of the inorganic cation-anion difference (C(+)(nm)-A(-)(nm)) method based on dietary ash-acidity titration after the oxidative combustion of food samples. Besides the inorganic components of TA (A(-)(nm)-C(+)(nm)), which are under renal control, there are also metabolizable components (A(-)(nm)-C(+)(nm)) of TA, which are under the control of the intermediate metabolism. The whole body base balance, NBb(W), is obtained only by the application of C(+)(nm)-A(-)(nm) to food, feces and urine, while the metabolizable component (A(-)(nm)-C(+)(nm)) is disregarded. A novel method has been subsequently suggested to calculate the net balance of fixed acid, made up by the difference between the input of net endogenous acid production: NEAP = SO(4)(2-)+A(-)(m)-(C(+)(nm)-A(-)(nm)), and the output of net acid excretion: NAE = TA + NH(4)(+) - HCO(3)(-). This approach has been criticized because 1) it includes metabolizable acids, whose production cannot be measured independently; 2) the specific control of metabolizable acid and base has been incorrectly attributed to the kidney; 3) the inclusion of A-m in the balance input generates an acid overload; 4) the object of measurement in making up a balance has to be the same, a condition not fulfilled as NEAP is different from NAE. Lastly, by rearranging the net balance of the acid equation, the balance of nonmetabolizable acid equation is obtained. Therefore, any discrepancy between these two equations is due to the inaccuracy in the urine measurement of metabolizable cations and/or anions.

  8. Synthesis and Performance Properties of Cationic Fabric Softeners Derived from Free Fatty Acid of Tallow Fat.

    PubMed

    Mondal, Mithun G; Pratap, Amit Prabhakar

    2016-08-01

    Esterquat cationic softener is basically the class of surface active quaternary ammonium compounds. Esterquat compounds were synthesized and their surface behavior, antibacterial activity and Textile softening properties were investigated. Easily found cheap material was used to synthesize cationic fabric softeners. This fabric softener will be a good for commercially and industrially important because their emulsify activity, rewettability dispersing power and softness. Free fatty acids were derived from tallow oil and were treated with triethanolamine and mono-ethanolamine at 140°C. This diester was quaternaries with dimethyl sulphate and benzyl chloride. The synthesized esterquat compounds were characterized by its cationic content, 1H NMR and FT-IR analysis. In addition to the cationic content, surface tension, CMC (critical micelle concentration), rewettability, fabric softening, emulsification and dispersing power were determined as their surface-active properties. The fabric softening activity of esterquat and esteramide prepared from DMS was better softening activity of fabrics compared to untreated cotton and polyester fabrics cloth. The presented result shows that the esterquat made from BCl exhibit the best dispersing power. The esterquat made from DMS both in TEA and MEA shows good rewettability was determined. PMID:27430381

  9. Effects of metal cations and fulvic acid on the adsorption of ciprofloxacin onto goethite.

    PubMed

    Tan, Yinyue; Guo, Yong; Gu, Xueyuan; Gu, Cheng

    2015-01-01

    Ciprofloxacin (CIP) can be strongly adsorbed by ferric oxides, but some influencing factors, such as multivalent cations and soil organic matter, have not been evaluated extensively. In this study, the interaction between CIP and four divalent metals (Ca, Cd, Cu, and Pb) was investigated using potentiometric titration and the results indicated that CIP can bind to the divalent metals in the following affinity order: Cu(II) > Pb(II) > Cd(II) > Ca(II). The effects of metals and fulvic acid (FA) on the adsorption behavior of CIP onto goethite surfaces were also examined using batch experiments. It was found that metal cations enhanced the CIP retention on goethite surfaces in the same order as the affinity order with CIP, indicating that metals likely increased CIP retention through cation bridging. FA was found to promote CIP sorption rather than compete with it, and the coexistence of FA and Cu(II) in the system exhibited an addictive effect with CIP sorption, indicating that they might influence the sorption separately under the studied loading condition. Taken together, our results suggested that the coexistence of divalent cations or soil organic matter will enhance CIP sorption on goethite surfaces, hence reducing its mobility and bioavailability in the environment.

  10. Fibrous polymer grafted magnetic chitosan beads with strong poly(cation-exchange) groups for single step purification of lysozyme.

    PubMed

    Bayramoglu, Gulay; Tekinay, Turgay; Ozalp, V Cengiz; Arica, M Yakup

    2015-05-15

    Lysozyme is an important polypetide used in medical and food applications. We report a novel magnetic strong cation exchange beads for efficient purification of lysozyme from chicken egg white. Magnetic chitosan (MCHT) beads were synthesized via phase inversion method, and then grafted with poly(glycidyl methacrylate) (p(GMA)) via the surface-initiated atom transfer radical polymerization (SI-ATRP). Epoxy groups of the grafted polymer, were modified into strong cation-exchange groups (i.e., sulfonate groups) in the presence of sodium sulfite. The MCTH and MCTH-g-p(GMA)-SO3H beads were characterized by ATR-FTIR, SEM, and VSM. The sulphonate groups content of the modified MCTH-g-p(GMA)-4 beads was found to be 0.53mmolg(-1) of beads by the potentiometric titration method. The MCTH-g-p(GMA)-SO3H beads were first used as an ion-exchange support for adsorption of lysozyme from aqueous solution. The influence of different experimental parameters such as pH, contact time, and temperature on the adsorption process was evaluated. The maximum adsorption capacity was found to be 208.7mgg(-1) beads. Adsorption of lysozyme on the MCTH-g-p(GMA)-SO3H beads fitted to Langmuir isotherm model and followed the pseudo second-order kinetic. More than 93% of the adsorbed lysozyme was desorbed using Na2CO3 solution (pH 11.0). The purity of the lysozyme was checked by HPLC and SDS gel electrophoresis. In addition, the MCTH-g-p(GMA)-SO3H beads prepared in this work showed promising potential for separation of various anionic molecules. PMID:25864009

  11. Room Temperature Cation Exchange Reaction in Nanocrystals for Ultrasensitive Speciation Analysis of Silver Ions and Silver Nanoparticles.

    PubMed

    Huang, Ke; Xu, Kailai; Tang, Jie; Yang, Lu; Zhou, Jingrong; Hou, Xiandeng; Zheng, Chengbin

    2015-07-01

    To evaluate the toxicity of silver nanoparticles (AgNPs) and Ag(+) and gain deep insight into the transformation of AgNPs in the environment or organisms, ultrasensitive analytical methods are needed for their speciation analysis. About 40-fold of Cd(2+) in CdTe ionic nanocrystals can be "bombarded-and-exploded" (exchanged) in less than 1 min simply by mixing the nanocrystals with Ag(+) solution at room temperature, while this cation exchange reaction did not occur when only silver nanoparticles were present. On the basis of this striking difference, an ultrasensitive method was developed for speciation analysis of Ag(+) and AgNPs in complex matrices. The released Cd(2+) was reduced to its volatile species by sodium tetrahydroborate, which was separated and swept to an inductively coupled plasma mass spectrometer (ICPMS) or an atomic fluorescence spectrometer (AFS) for the indirect but ultrasensitive detection of Ag(+). Owing to the remarkable signal amplification via the cation exchange reaction and the advantages of chemical vapor generation for sampling, the limit of detection was 0.0003 μg L(-1) for Ag(+) by ICPMS, which was improved by 100-fold compared to the conventional method. Relative standard deviations are better than 2.5% at a concentration of 0.5 μg L(-1) Ag(+) or AgNPs regardless of the detector. The proposed method retains several unique advantages, including ultrahigh sensitivity, speciation analysis, simplicity and being organic reagent-free, and has been successfully utilized for speciation analysis of Ag(+) and AgNPs in environmental water samples and paramecium cells. PMID:26017198

  12. Tuning hydrophobicity of highly cationic tetradecameric Gramicidin S analogues using adamantane amino acids.

    PubMed

    Knijnenburg, Annemiek D; Kapoerchan, Varsha V; Spalburg, Emile; de Neeling, Albert J; Mars-Groenendijk, Roos H; Noort, Daan; van der Marel, Gijs A; Overkleeft, Herman S; Overhand, Mark

    2010-12-01

    Ring extended Gramicidin S analogues containing adamantane amino acids and six cationic residues were designed and evaluated. Systematic replacement of the hydrophobic residues with adamantane amino acids resulted in a small set of compounds with varying amphipathic character. It was found that the amphipathicity of these compounds is correlated to their biological activity. Several bacterial strains including MRSA strains were shown to be killed by the novel peptides. The most potent antibacterial peptides are tetradecameric GS analogues containing six positives charges and two adamantane moieties.

  13. Anthropogenically driven changes in chloride complicate interpretation of base cation trends in lakes recovering from acidic deposition.

    PubMed

    Rosfjord, Catherine H; Webster, Katherine E; Kahl, Jeffrey S; Norton, Stephen A; Fernandez, Ivan J; Herlihy, Alan T

    2007-11-15

    Declines in Ca and Mg in low ANC lakes recovering from acidic deposition are widespread across the northern hemisphere. We report overall increases between 1984 and 2004 in the concentrations of Ca + Mg and Cl in lakes representing the statistical population of nearly 4000 low ANC lakes in the northeast U.S. Increases in Cl occurred in nearly all lakes in urbanized southern New England, but only 18% of lakes in more remote Maine had Cl increases. This spatial pattern implicates road salt application as the major source of the increased Cl salts. Among the 48% of the lake population classified as salt-affected, the median changes in Cl (+133 microeq/L) and Ca + Mg (+47 microeq/ L) were large and positive in direction over the 20 years. However, in the unaffected lakes, Cl remained stable and Ca + Mg decreased (-3 microeq/L), consistent with reported long-term trends in base cations of acid-sensitive lakes. This discrepancy between the Cl groups suggests that changes in ion exchange processes in salt-affected watersheds have altered the geochemical cycling of Ca and Mg. One policy-relevant implication is that waters influenced by Cl salts complicate regional assessments of surface water recovery from "acid rain" related to the passage of the Clean Air Act.

  14. Ion-exchange chromatographic analysis of peroxynitric acid.

    PubMed

    Nakashima, Yoichi; Ikawa, Satoshi; Tani, Atsushi; Kitano, Katsuhisa

    2016-01-29

    Ion-exchange chromatographic analysis of peroxynitric acid (O2NOOH) was performed by combining an acidic eluate with an UV-vis detector and immersing the separation column in an ice-water bath. The decomposition behavior of peroxynitric acid in the solution was also studied using this system. The fraction for the peroxynitric acid peak was collected. Ion-exchange chromatographic analysis of this fraction, after standing at room temperature for 24h, showed that the decomposition products were mainly nitrate ions with a very small amount of nitrous acid. The peroxynitric acid peak area correlated perfectly with the total amount of decomposition products. The ion-exchange chromatographic isolation allowed us to evaluate the molar extinction coefficient of peroxynitric acid precisely in a wider wavelength range than previous reports. The value decreases monotonically from 1729±26M(-1)cm(-1) at 200nm to 12.0±0.5M(-1)cm(-1) at 290nm. PMID:26748867

  15. Selective cation exchange in the core region of Cu2-xSe/Cu2-xS core/shell nanocrystals.

    PubMed

    Miszta, Karol; Gariano, Graziella; Brescia, Rosaria; Marras, Sergio; De Donato, Francesco; Ghosh, Sandeep; De Trizio, Luca; Manna, Liberato

    2015-09-30

    We studied cation exchange (CE) in core/shell Cu2-xSe/Cu2-xS nanorods with two cations, Ag(+) and Hg(2+), which are known to induce rapid exchange within metal chalcogenide nanocrystals (NCs) at room temperature. At the initial stage of the reaction, the guest ions diffused through the Cu2-xS shell and reached the Cu2-xSe core, replacing first Cu(+) ions within the latter region. These experiments prove that CE in copper chalcogenide NCs is facilitated by the high diffusivity of guest cations in the lattice, such that they can probe the whole host structure and identify the preferred regions where to initiate the exchange. For both guest ions, CE is thermodynamically driven as it aims for the formation of the chalcogen phase characterized by the lower solubility under the specific reaction conditions. PMID:26360611

  16. Selective Cation Exchange in the Core Region of Cu2–xSe/Cu2–xS Core/Shell Nanocrystals

    PubMed Central

    2015-01-01

    We studied cation exchange (CE) in core/shell Cu2–xSe/Cu2–xS nanorods with two cations, Ag+ and Hg2+, which are known to induce rapid exchange within metal chalcogenide nanocrystals (NCs) at room temperature. At the initial stage of the reaction, the guest ions diffused through the Cu2–xS shell and reached the Cu2–xSe core, replacing first Cu+ ions within the latter region. These experiments prove that CE in copper chalcogenide NCs is facilitated by the high diffusivity of guest cations in the lattice, such that they can probe the whole host structure and identify the preferred regions where to initiate the exchange. For both guest ions, CE is thermodynamically driven as it aims for the formation of the chalcogen phase characterized by the lower solubility under the specific reaction conditions. PMID:26360611

  17. Selective cation exchange in the core region of Cu2-xSe/Cu2-xS core/shell nanocrystals.

    PubMed

    Miszta, Karol; Gariano, Graziella; Brescia, Rosaria; Marras, Sergio; De Donato, Francesco; Ghosh, Sandeep; De Trizio, Luca; Manna, Liberato

    2015-09-30

    We studied cation exchange (CE) in core/shell Cu2-xSe/Cu2-xS nanorods with two cations, Ag(+) and Hg(2+), which are known to induce rapid exchange within metal chalcogenide nanocrystals (NCs) at room temperature. At the initial stage of the reaction, the guest ions diffused through the Cu2-xS shell and reached the Cu2-xSe core, replacing first Cu(+) ions within the latter region. These experiments prove that CE in copper chalcogenide NCs is facilitated by the high diffusivity of guest cations in the lattice, such that they can probe the whole host structure and identify the preferred regions where to initiate the exchange. For both guest ions, CE is thermodynamically driven as it aims for the formation of the chalcogen phase characterized by the lower solubility under the specific reaction conditions.

  18. Ae4 (Slc4a9) is an electroneutral monovalent cation-dependent Cl-/HCO3- exchanger.

    PubMed

    Peña-Münzenmayer, Gaspar; George, Alvin T; Shull, Gary E; Melvin, James E; Catalán, Marcelo A

    2016-05-01

    Ae4 (Slc4a9) belongs to the Slc4a family of Cl(-)/HCO3 (-) exchangers and Na(+)-HCO3 (-) cotransporters, but its ion transport cycle is poorly understood. In this study, we find that native Ae4 activity in mouse salivary gland acinar cells supports Na(+)-dependent Cl(-)/HCO3 (-) exchange that is comparable with that obtained upon heterologous expression of mouse Ae4 and human AE4 in CHO-K1 cells. Additionally, whole cell recordings and ion concentration measurements demonstrate that Na(+) is transported by Ae4 in the same direction as HCO3 (-) (and opposite to that of Cl(-)) and that ion transport is not associated with changes in membrane potential. We also find that Ae4 can mediate Na(+)-HCO3 (-) cotransport-like activity under Cl(-)-free conditions. However, whole cell recordings show that this apparent Na(+)-HCO3 (-) cotransport activity is in fact electroneutral HCO3 (-)/Na(+)-HCO3 (-) exchange. Although the Ae4 anion exchanger is thought to regulate intracellular Cl(-) concentration in exocrine gland acinar cells, our thermodynamic calculations predict that the intracellular Na(+), Cl(-), and HCO3 (-) concentrations required for Ae4-mediated Cl(-) influx differ markedly from those reported for acinar secretory cells at rest or under sustained stimulation. Given that K(+) ions share many properties with Na(+) ions and reach intracellular concentrations of 140-150 mM (essentially the same as extracellular [Na(+)]), we hypothesize that Ae4 could mediate K(+)-dependent Cl(-)/HCO3 (-) exchange. Indeed, we find that Ae4 mediates Cl(-)/HCO3 (-) exchange activity in the presence of K(+) as well as Cs(+), Li(+), and Rb(+) In summary, our results strongly suggest that Ae4 is an electroneutral Cl(-)/nonselective cation-HCO3 (-) exchanger. We postulate that the physiological role of Ae4 in secretory cells is to promote Cl(-) influx in exchange for K(+)(Na(+)) and HCO3 (-) ions.

  19. Mesoporous MFI zeolites by microwave induced assembly between sulfonic acid functionalized MFI zeolite nanoparticles and alkyltrimethylammonium cationic surfactants.

    PubMed

    Jin, Hailian; Ansari, Mohd Bismillah; Park, Sang-Eon

    2011-07-14

    Mesoporous MFI zeolites (ZSM-5, TS-1, S-1) having intracrystalline mesoporosity within zeolite crystals were synthesized by microwave induced assembly through the ionic interaction between the sulfonic acid functionalized MFI zeolite nanoparticles and alkyltrimethylammonium cationic surfactants.

  20. Dextran-grafted cation exchanger based on superporous agarose gel: adsorption isotherms, uptake kinetics and dynamic protein adsorption performance.

    PubMed

    Shi, Qing-Hong; Jia, Guo-Dong; Sun, Yan

    2010-07-30

    A novel chromatographic medium for high-capacity protein adsorption was fabricated by grafting dextran (40kDa) onto the pore surfaces of superporous agarose (SA) beads. The bead was denoted as D-SA. D-SA, SA and homogeneous agarose (HA) beads were modified with sulfopropyl (SP) group to prepare cation exchangers, and the adsorption and uptake of lysozyme on all three cation-exchange chromatographic beads (SP-HA, SP-SA and SP-D-SA) were investigated at salt concentrations of 6-50mmol/L. Static adsorption experiments showed that the adsorption capacity of SP-D-SA (2.24mmol/g) was 78% higher than that of SP-SA (1.26mmol/g) and 54% higher than that of SP-HA (1.45mmol/g) at a salt concentration of 6mmol/L. Moreover, salt concentration had less influence on the adsorption capacity and dissociation constant of SP-D-SA than it did on SP-HA, suggesting that dextran-grafted superporous bead is a more potent architecture for chromatographic beads. In the dynamic uptake of lysozyme to the three cation-exchange beads, the D(e)/D(0) (the ratio of effective pore diffusivity to free solution diffusivity) values of 1.6-2.0 were obtained in SA-D-SA, indicating that effective pore diffusivities of SP-D-SA were about two times higher than free solution diffusivity for lysozyme. At 6mmol/L NaCl, the D(e) value in SA-D-SA (22.0x10(-11)m(2)/s) was 14.4-fold greater than that in SP-HA. Due to the superior uptake kinetics in SA-D-SA, the highest dynamic binding capacity (DBC) and adsorption efficiency (the ratio of DBC to static adsorption capacity) was likewise found in SP-D-SA. It is thus confirmed that SP-D-SA has combined the advantages of superporous matrix structure and drafted ligand chemistry in mass transport and offers a new opportunity for the development of high-performance protein chromatography.

  1. Ion-pairing ability, chemical stability, and selectivity behavior of halogenated dodecacarborane cation exchangers in neutral carrier-based ion-selective electrodes.

    PubMed

    Peper, Shane; Qin, Yu; Almond, Philip; McKee, Michael; Telting-Diaz, Martin; Albrecht-Schmitt, Thomas; Bakker, Eric

    2003-05-01

    Recently, it has been discovered that carba-closo-dodecaborates can be used as cation exchangers in neutral carrier-based ion-selective chemical sensors. Because of their inherent chemical stability and versatile functionalization chemistries, they offer many advantages that may potentially be exploited for ion analyses that require nontraditional sample conditions, including strongly acidic media. In this work, trimethylammonium salts of undecachlorinated (UCC), undecabrominated (UBC), hexabrominated (HBC), and undecaiodinated (UIC) carborane anions were prepared and evaluated for their potential use in solvent polymeric membrane-based sensors. Computational methods including Natural population analysis and electrostatic mapping were used to predict the ion-exchanging ability of each lipophilic anion. In addition, the sandwich membrane technique was used to evaluate the ion-pairing ability of each carborane anion in situ (i.e., within bis(2-ethylhexyl) sebacate (DOS)- and 2-nitrophenyl octyl ether (o-NPOE)-plasticized ISE membranes). The results of the computational and potentiometric studies found that binding affinity of the anions followed the generalized trend HBC > UCC > UBC > UIC. PVC-DOS bulk optode thin films containing the chromoionophore ETH 5315 and a respective anion were used to determine the chemical stability/lipophilicity of the carboranes and tetrakis[3,5-bis(trifluoromethyl)phenyl] borate (TFPB) in acidic media (0.2 M HOAc) under flowing conditions. The studies found that in terms of stability/lipophilicity UIC > UBC > TFPB approximately UCC > HBC. Electrodes containing a Pb(2+)-selective ionophore, tert-butylcalix[4]arene-tetrakis(N,N-dimethylthioacetamide)(lead IV), were used to evaluate the functionality of each cation exchanger. An evaluation of response characteristics such as slope and selectivity found that UIC and UBC were quite comparable to the behavior of TFPB. Interestingly, both UIC and UBC showed a marked selectivity improvement

  2. Mineral Separation in a CELSS by Ion-exchange Chromatography

    NASA Technical Reports Server (NTRS)

    Ballou, E. V.; Spitze, L. A.; Wong, F. W.; Wydeven, T.; Johnson, C. C.

    1982-01-01

    Operational parameters pertinent to ion exchange chromatography separation were identified. The experiments were performed with 9 mm diameter ion exchange columns and conventional column accessories. The cation separation beds were packed with AG 50W-X2 strong acid cation exchange resin in H(+) form and 200-400 dry mesh particle size. The stripper beds used in some experiments were packed with AG 1-XB strong base cation exchange resin in OH(-) form and 200-400 dry mesh particle size.

  3. Cationic liposome–nucleic acid complexes for gene delivery and gene silencing

    PubMed Central

    Ewert, Kai K.; Majzoub, Ramsey N.; Leal, Cecília

    2014-01-01

    Cationic liposomes (CLs) are studied worldwide as carriers of DNA and short interfering RNA (siRNA) for gene delivery and gene silencing, and related clinical trials are ongoing. Optimization of transfection efficiency and silencing efficiency by cationic liposome carriers requires a comprehensive understanding of the structures of CL–nucleic acid complexes and the nature of their interactions with cell membranes as well as events leading to release of active nucleic acids within the cytoplasm. Synchrotron x-ray scattering has revealed that CL–nucleic acid complexes spontaneously assemble into distinct liquid crystalline phases including the lamellar, inverse hexagonal, hexagonal, and gyroid cubic phases, and fluorescence microscopy has revealed CL–DNA pathways and interactions with cells. The combining of custom synthesis with characterization techniques and gene expression and silencing assays has begun to unveil structure–function relations in vitro. As a recent example, this review will briefly describe experiments with surface-functionalized PEGylated CL–DNA nanoparticles. The functionalization, which is achieved through custom synthesis, is intended to address and overcome cell targeting and endosomal escape barriers to nucleic acid delivery faced by PEGylated nanoparticles designed for in vivo applications. PMID:25587216

  4. Physical Property Requirements of Ion-exchange Polymer Membranes for Acid-base Flow Batteries

    NASA Astrophysics Data System (ADS)

    Roddecha, Supacharee; Thayer, Peter; Jorne', Jacob; Anthamatten, Mitchell

    2013-03-01

    Flow batteries offer feasible solutions to grid-scale storage of intermittent power. We are developing a new type of flow battery that reversibly controls an acid-base neutralization reaction. The battery consists of two highly reversible hydrogen gas electrodes that are exposed to low and high pH process streams. A brine solution runs between the acid and base streams and is separated by cationic and anionic exchange membranes. For both charge and discharge phases, hydrogen gas is produced at one electrode and consumed at the other. During charging, an external potential is applied across the two electrodes to electrochemically produce acid and base from the fed brine solution. Discharge involves electrochemical neutralization of acid and base streams, resulting in current flow through an external load. Several charge and discharge cycles were performed to demonstrate proof of concept. Experiments were conducted to determine the physical property requirements of the ionic exchange polymer layers. Properties including ion conductivity, permselectivity, and membrane stability will be discussed.

  5. Formation of ZnSe/Bi{sub 2}Se{sub 3} QDs by surface cation exchange and high photothermal conversion

    SciTech Connect

    Jia, Guozhi; Wang, Peng; Zhang, Yanbang; Wu, Zengna; Li, Qiang; Yao, Jianghong; Chang, Kai

    2015-08-15

    Water-dispersed core/shell structure ZnSe/Bi{sub 2}Se{sub 3} quantum dots were synthesized by ultrasonicwave-assisted cation exchange reaction. Only surface Zn ion can be replaced by Bi ion in ZnSe quantum dots, which lead to the ultrathin Bi{sub 2}Se{sub 3} shell layer formed. It is significance to find to change the crystal of QDs due to the acting of ultrasonicwave. Cation exchange mechanism and excellent photothermal conversion properties are discussed in detail.

  6. Colorimetric Humidity and Solvent Recognition Based on a Cation-Exchange Clay Mineral Incorporating Nickel(II)-Chelate Complexes.

    PubMed

    Hosokawa, Hitoshi; Mochida, Tomoyuki

    2015-12-01

    Solvatochromic nickel(II) complexes with diketonato and diamine ligands were incorporated into a saponite clay by ion exchange, and their colorimetric humidity- and solvent-recognition properties were investigated. These powders exhibit color change from red to blue-green depending on humidity, and the detection range can be controlled by modifying the metal complex. The humidity response takes advantage of the humidity-dependent water content in clay and the coordination of water molecules to the metal complex in equilibrium. The addition of organic solvents to the powders causes a color change to occur, varying from red to blue-green depending on the donor number of the solvent, thereby enabling solvent recognition. In the clay, the affinity of less sterically hindered complexes to water or solvent molecules is decreased compared with that in solution because the cationic complexes interact with the anionic layers in the clay. Incorporating diethylene glycol into the materials produced thermochromic powders.

  7. Strong cation exchange chiral stationary phase--a comparative study in high-performance liquid chromatography and subcritical fluid chromatography.

    PubMed

    Wolrab, Denise; Macíková, Pavla; Boras, Mario; Kohout, Michal; Lindner, Wolfgang

    2013-11-22

    The performance of a strong cation exchange-type (SCX) chiral stationary phase (CSP) was evaluated with subcritical fluid chromatography (subFC) and high performance liquid chromatography (HPLC). The chromatographic conditions in subFC were optimized by changing the amount of polar organic modifier, concentration of a basic additive in the modifier, system pressure and temperature. In this way the concentration of in situ formed transient ionic species could be varied. The gradual change of the concentration of the transient buffer, i.e. gradient elution conditions in subFC, was found beneficial for separation of a mixture of racemic compounds. The strength and amount of the in situ formed buffer was estimated on the basis of comparative experiments in subSFC and HPLC.

  8. Selective separation and purification of highly polar basic compounds using a silica-based strong cation exchange stationary phase.

    PubMed

    Long, Zhen; Guo, Zhimou; Xue, Xingya; Zhang, Xiuli; Nordahl, Lilly; Liang, Xinmiao

    2013-12-01

    Compared to moderately and weakly hydrophilic bases, highly polar basic compounds are even more difficult to separate due to their poor retention in reversed phase (RP) mode. This study described the successful applications of a strong cation exchange (SCX) stationary phase to achieve symmetric peak shape, adequate retention and selectivity in the separation of very polar basic compounds. Salt and acetonitrile concentrations were adjusted to optimize the separation. Good correlations (R(2)=0.998-1.000) between the logarithm of the retention factor and the logarithm of salt or acetonitrile concentration were obtained. Gradients generated by changing salt or acetonitrile concentration were compared for the analysis of different highly polar bases. Although all of the analytes were eluted more quickly with an acetonitrile gradient, the effect of the gradients tested on peak width and peak shape varied with respect to analyte. In addition, the effects of different types of cation and anion additives were also investigated. After separation parameters were acquired, the SCX-based method was utilized to analyze highly hydrophilic alkaloids from Scopolia tangutica Maxim with high separation efficiency (plate numbers>32,000 m(-1)). Concurrently, one very polar alkaloid fraction was purified with symmetric peak shape using the current method. Our results suggest that SCX stationary phase can be used as an alternative to RP stationary phase in the analysis and purification of highly hydrophilic basic compounds. PMID:24267097

  9. Cation Exchange Strategy for the Encapsulation of a Photoactive CO-Releasing Organometallic Molecule into Anionic Porous Frameworks.

    PubMed

    Carmona, Francisco J; Rojas, Sara; Sánchez, Purificación; Jeremias, Hélia; Marques, Ana R; Romão, Carlos C; Choquesillo-Lazarte, Duane; Navarro, Jorge A R; Maldonado, Carmen R; Barea, Elisa

    2016-07-01

    The encapsulation of the photoactive, nontoxic, water-soluble, and air-stable cationic CORM [Mn(tacn)(CO)3]Br (tacn = 1,4,7-triazacyclononane) in different inorganic porous matrixes, namely, the metalorganic framework bio-MOF-1, (NH2(CH3)2)2[Zn8(adeninate)4(BPDC)6]·8DMF·11H2O (BPDC = 4,4'-biphenyldicarboxylate), and the functionalized mesoporous silicas MCM-41-SO3H and SBA-15-SO3H, is achieved by a cation exchange strategy. The CO release from these loaded materials, under simulated physiological conditions, is triggered by visible light. The results show that the silica matrixes, which are unaltered under physiological conditions, slow the kinetics of CO release, allowing a more controlled CO supply. In contrast, bio-MOF-1 instability leads to the complete leaching of the CORM. Nevertheless, the degradation of the MOF matrix gives rise to an enhanced CO release rate, which is related to the presence of free adenine in the solution.

  10. Effect of exchangeable cations on apparent diffusion of Ca 2+ ions in Na- and Ca-montmorillonite mixtures

    NASA Astrophysics Data System (ADS)

    Kozaki, T.; Sawaguchi, T.; Fujishima, A.; Sato, S.

    Compacted Na-bentonite, of which the major mineral is montmorillonite, is a candidate buffer material for the geological disposal of high-level radioactive waste. A potential alteration of the bentonite in a repository is the partial replacement of the exchangeable cations of Na + with Ca 2+. The Ca 2+ cations could be released from cementitious materials and diffuse into the buffer material in the repository. In this study, to evaluate the alteration that could reduce the performance of the bentonite buffer, the apparent diffusion coefficients of HTO and Ca 2+ ions were determined from non-steady, one-dimensional diffusion experiments using Na- and Ca-montmorillonite mixtures with different ionic equivalent fractions of Ca 2+ ions. The apparent diffusion coefficient of HTO at a dry density of 1.0 Mg m -3 slightly increased with an increase in the ionic equivalent fraction of Ca 2+ ions. However, the apparent diffusion coefficient of Ca 2+ and the activation energy for diffusion at the same dry density were independent of the ionic equivalent fraction of Ca 2+ ions. These findings suggest that unlike HTO, which can be postulated to diffuse mainly in pore water, Ca 2+ ion diffusion could occur predominantly in interlayer spaces, of which the basal spacing was determined to be constant by the XRD technique.

  11. Potential heat exchange fluids for use in sulfuric acid vaporizers

    NASA Technical Reports Server (NTRS)

    Lawson, D. D.; Petersen, G. R.

    1981-01-01

    A series of liquids have been screened as candidate heat exchange fluids for service in thermochemical cycles that involve the vaporization of sulfuric acid. The required chemical and physical criteria of the liquids is described with the results of some preliminary high temperature test data presented.

  12. Heat-Exchange Fluids for Sulfuric Acid Vaporizers

    NASA Technical Reports Server (NTRS)

    Lawson, D. D.; Petersen, G. R.

    1982-01-01

    Some fluorine-substituted organic materials meet criteria for heat-exchange fluids in contact with sulfuric acid. Most promising of these are perfluoropropylene oxide polymers with degree of polymerization (DP) between 10 and 50. It is desirable to have DP in high range because vapor pressure of material decreases as DP increases, and high-DP liquids have lower loss due to vaporization.

  13. Evolution of hollow TiO2 nanostructures via the Kirkendall effect driven by cation exchange with enhanced photoelectrochemical performance.

    PubMed

    Yu, Yanhao; Yin, Xin; Kvit, Alexander; Wang, Xudong

    2014-05-14

    Hollow nanostructures are promising building blocks for electrode scaffolds and catalyst carriers in energy-related systems. In this paper, we report a discovery of hollow TiO2 nanostructure evolution in a vapor-solid deposition system. By introducing TiCl4 vapor pulses to ZnO nanowire templates, we obtained TiO2 tubular nanostructures with well-preserved dimensions and morphology. This process involved the cation exchange reaction between TiCl4 vapor and ZnO solid and the diffusion of reactants and products in their vapor or solid phases, which was likely a manifestation of the Kirkendall effect. The characteristic morphologies and the evolution phenomena of the hollow nanostructures from this vapor-solid system were in a good agreement with the Kirkendall effect discovered in solution systems. Complex hollow TiO2 nanostructures were successfully acquired by replicating various ZnO nanomorphologies, suggesting that this unique cation exchange process could also be a versatile tool for nanostructure replication in vapor-solid growth systems. The evolution of TiO2 nanotubes from ZnO NW scaffolds was seamlessly integrated with TiO2 NR branch growth and thus realized a pure TiO2-phased 3D NW architecture. Because of the significantly enlarged surface area and the trace amount of Zn left in the TiO2 crystals, such 3D TiO2 nanoforests demonstrated enhanced photoelectrochemical performance particularly under AM (air mass) 1.5G illumination, offering a new route for hierarchical functional nanomaterial assembly and application.

  14. Common Ion Effects In Zeoponic Substrates: Dissolution And Cation Exchange Variations Due to Additions of Calcite, Dolomite and Wollastonite

    NASA Technical Reports Server (NTRS)

    Beiersdorfer, R. E.; Ming, D. W.; Galindo, C., Jr.

    2003-01-01

    c1inoptilolite-rich tuff-hydroxyapatite mixture (zeoponic substrate) has the potential to serve as a synthetic soil-additive for plant growth. Essential plant macro-nutrients such as calcium, phosphorous, magnesium, ammonium and potassium are released into solution via dissolution of the hydroxyapatite and cation exchange on zeolite charged sites. Plant growth experiments resulting in low yield for wheat have been attributed to a Ca deficiency caused by a high degree of cation exchange by the zeolite. Batch-equilibration experiments were performed in order to determine if the Ca deficiency can be remedied by the addition of a second Ca-bearing, soluble, mineral such as calcite, dolomite or wollastonite. Variations in the amount of calcite, dolomite or wollastonite resulted in systematic changes in the concentrations of Ca and P. The addition of calcite, dolomite or wollastonite to the zeoponic substrate resulted in an exponential decrease in the phosphorous concentration in solution. The exponential rate of decay was greatest for calcite (5.60 wt. % -I), intermediate for wollastonite (2.85 wt.% -I) and least for dolomite (1.58 wt.% -I). Additions of the three minerals resulted in linear increases in the calcium concentration in solution. The rate of increase was greatest for calcite (3.64), intermediate for wollastonite (2.41) and least for dolomite (0.61). The observed changes in P and Ca concentration are consistent with the solubilities of calcite, dolomite and wollastonite and with changes expected from a common ion effect with Ca. Keywords: zeolite, zeoponics, common-ion effect, clinoptilolite, hydroxyapatite

  15. The rapid identification of elution conditions for therapeutic antibodies from cation-exchange chromatography resins using high-throughput screening.

    PubMed

    McDonald, Paul; Tran, Benjamin; Williams, Christopher R; Wong, Marc; Zhao, Ti; Kelley, Brian D; Lester, Philip

    2016-02-12

    Cation-exchange chromatography is widely used in the purification of therapeutic antibodies, wherein parameters such as elution pH and counterion concentration require optimization for individual antibodies across different chromatography resins. With a growing number of antibodies in clinical trials and the pressure to expedite process development, we developed and automated a high-throughput batch-binding screen to more efficiently optimize elution conditions for cation-exchange chromatography resins. The screen maps the binding behavior of antibodies and impurities as a function of pH and counterion concentration in terms of a partition coefficient (Kp). Using this approach, the binding behavior of a library of antibodies was assessed on Poros 50HS and SP Sepharose Fast Flow resins. The diversity in binding behavior between antibodies and across resins translated to the requirement of a variable counterion concentration to elute each antibody. This requirement can be met through the use of a gradient elution. However, a gradient of increasing counterion concentration spans the transition from binding to non-binding for impurities as well as the antibody, resulting in the elution of impurities within the antibody elution peak. Step elution conditions that selectively elute the antibody while retaining impurities on the resin can now be rapidly identified using our high-throughput approach. We demonstrate that by correlating antibody Kp to elution pool volume and yield on packed-bed columns and through the calculation of a separation factor, we can efficiently optimize step elution conditions that maximize impurity clearance and yield for each antibody. PMID:26803905

  16. The effect of positioning cations on acidity and stability of the framework structure of Y zeolite.

    PubMed

    Deng, Changshun; Zhang, Junji; Dong, Lihui; Huang, Meina; Bin Li; Jin, Guangzhou; Gao, Junbin; Zhang, Feiyue; Fan, Minguang; Zhang, Luoming; Gong, Yanjun

    2016-01-01

    The investigation on the modification of NaY zeolite on LaHY and AEHY (AE refers Ca and Sr and the molar ratio of Ca and Sr is 1:1) zeolites was proformed by XRD, N2-physisorption (BET), XRF, XPS, NH3-TPD, Py-IR, hydrothermal stability, and catalytic cracking test. These results indicate that HY zeolite with ultra low content Na can be obtained from NaY zeolite through four exchange four calcination method. The positioning capability of La(3+) in sodalite cage is much better than that of AE(2+) and about 12 La(3+) can be well coordinated in sodalite cages of one unit cell of Y zeolite. Appropriate acid amount and strength favor the formation of propylene and La(3+) is more suitable for the catalytic cracking of cyclohexane than that of AE(2+). Our results not only elaborate the variation of the strong and weak acid sites as well as the Brönsted and Lewis acid sites with the change of exchanged ion content but also explore the influence of hydrothermal aging of LaHY and AEHY zeolites and find the optimum ion exchange content for the most reserved acid sites. At last, the coordination state and stabilization of ion exchanged Y zeolites were discussed in detail. PMID:26987306

  17. The effect of positioning cations on acidity and stability of the framework structure of Y zeolite

    PubMed Central

    Deng, Changshun; Zhang, Junji; Dong, Lihui; Huang, Meina; Bin Li; Jin, Guangzhou; Gao, Junbin; Zhang, Feiyue; Fan, Minguang; Zhang, Luoming; Gong, Yanjun

    2016-01-01

    The investigation on the modification of NaY zeolite on LaHY and AEHY (AE refers Ca and Sr and the molar ratio of Ca and Sr is 1:1) zeolites was proformed by XRD, N2-physisorption (BET), XRF, XPS, NH3-TPD, Py-IR, hydrothermal stability, and catalytic cracking test. These results indicate that HY zeolite with ultra low content Na can be obtained from NaY zeolite through four exchange four calcination method. The positioning capability of La3+ in sodalite cage is much better than that of AE2+ and about 12 La3+ can be well coordinated in sodalite cages of one unit cell of Y zeolite. Appropriate acid amount and strength favor the formation of propylene and La3+ is more suitable for the catalytic cracking of cyclohexane than that of AE2+. Our results not only elaborate the variation of the strong and weak acid sites as well as the Brönsted and Lewis acid sites with the change of exchanged ion content but also explore the influence of hydrothermal aging of LaHY and AEHY zeolites and find the optimum ion exchange content for the most reserved acid sites. At last, the coordination state and stabilization of ion exchanged Y zeolites were discussed in detail. PMID:26987306

  18. Physical characterization of the state of motion of the phenalenyl spin probe in cation-exchanged faujasite zeolite supercages with pulsed EPR

    NASA Astrophysics Data System (ADS)

    Doetschman, D. C.; Dwyer, D. W.; Fox, J. D.; Frederick, C. K.; Scull, S.; Thomas, G. D.; Utterback, S. G.; Wei, J.

    1994-08-01

    The molecular motion of the phenalenyl (PNL) spin probe in the supercages of cation-exchanged X and Y zeolites (faujasites) has been physically characterized by pulsed and continuous wave (CW) electron paramagnetic resonance (EPR). Both X and Y zeolites, whose cation sites were exchanged with the alkali metal ions, Li +, Na +, K +, Rb + and Cs + were examined. There is a good correspondence between the temperature dependences of the PNL electron spin phase memory time and the CW EPR spectra. Both display evidence of a thermal activation from a stationary, non-rotating molecular state to a low-temperature state of in-plane rotation (Das et al., Chem Phys. 143 (1990) 253). The rate of in-plane rotation is an activated process, with E* | / R=1289 |+- 35 K and 1462 ± 47 K in NaX and KX zeolites, respectively. The rotation appears to be about an axis along which the half-filled, non-bonding π orbital interacts with the exchanged cation in the supercage. Both CW and pulsed EPR also show a higher temperature activation from the in-plane rotating state to an effectively isoptropic state of rotation of PNL in which the PNL-cation bond is thought to be broken, with E* ⊥ / R=2050 ± 110 K, 1956 ± 46K, 1335 ± 97 K in LiX, NaX and KX zeolites, respectively. The strength of the PNL-cation bonding decreases with increasing cation atomic number as indicated by E* ⊥ and the peripheral repulsion (crowding) of PNL increases with cation size as indicated E* |. There are qualitative indications that the binding of PNL to the cations in the Y zeolite is stronger than in the X zeolite.

  19. Potential of chiral anion-exchangers operated in various subcritical fluid chromatography modes for resolution of chiral acids.

    PubMed

    Pell, Reinhard; Lindner, Wolfgang

    2012-07-01

    Anion-exchange-type chiral stationary phases (CSPs) derived from quinine or quinidine were applied in subcritical fluid chromatography (SFC) for the direct separation of chiral acidic compounds. Employing subcritical (sc) mobile phase modes (CO₂ + methanol as co-solvent and acids and bases as additives) first the influence of type and amount of acidic and basic additives on separation performance was investigated. Secondly, water was tested as a neutral additive and the influence of temperature variation on enantioselectivity was studied. Thirdly, we could chromatographically confirm that the often verbalized "inherent acidity" of sc CO₂ + methanol is manifested by the in situ formation of methylcarbonic acids in the sc mobile phase and thus functioning as acidic additive. Accordingly the dissociated methylcarbonic acid, acting as a counterion, enables an anion exchange mechanism between the cationic CSP and the corresponding acidic analyte. In the absence of a dissociable acid in the mobile phase such an ion exchange mode would not work following a stoichiometric displacement model. This finding is further corroborated by the use of ammonia in methanol as co-solvent thus generating in situ the ammonium salt of methylcarbonic acid. In summary, we report on ion-exchange mediated chromatographic separations in SFC modes by merely using (i) sc CO₂ and MeOH, (ii) sc CO₂ and ammonia in MeOH, and (iii) sc CO₂ and MeOH plus acids and bases as additives. Comparisons to HPLC mode have been undertaken to evaluate merits and limitations. This mode exhibits high potential for preparative chromatography of chiral acids combining pronounced enantioselectivity with high column loadability and avoiding possibly troublesome mobile phase additives, as the in situ formed methylcarbonic acid disintegrates to CO₂ and methanol upon pressure release.

  20. Removal of lead compounds from polyvinylchloride in electric wires and cables using cation-exchange resin.

    PubMed

    Tsunekawa, Masami; Ito, Mayumi; Yuta, Sasaki; Tomoo, Sakai; Hiroyoshi, Naoki

    2011-07-15

    Recycling treatment of cable insulation resin generated from electric wires and cables was investigated. Conventional insulation PVC contains a lead component, tribase, as a thermal stabilizer and lead removal is necessary to recycle this PVC as insulation resin. This paper describes a solid surface adsorption method using ion exchange resin to remove the fine lead containing particles from PVC dissolved solution. Low lead concentration in the recovered PVC, complying with the requirements of RoHS, was achieved.

  1. Hypomorphic variants of cationic amino acid transporter 3 in males with autism spectrum disorders.

    PubMed

    Nava, Caroline; Rupp, Johanna; Boissel, Jean-Paul; Mignot, Cyril; Rastetter, Agnès; Amiet, Claire; Jacquette, Aurélia; Dupuits, Céline; Bouteiller, Delphine; Keren, Boris; Ruberg, Merle; Faudet, Anne; Doummar, Diane; Philippe, Anne; Périsse, Didier; Laurent, Claudine; Lebrun, Nicolas; Guillemot, Vincent; Chelly, Jamel; Cohen, David; Héron, Delphine; Brice, Alexis; Closs, Ellen I; Depienne, Christel

    2015-12-01

    Cationic amino acid transporters (CATs) mediate the entry of L-type cationic amino acids (arginine, ornithine and lysine) into the cells including neurons. CAT-3, encoded by the SLC7A3 gene on chromosome X, is one of the three CATs present in the human genome, with selective expression in brain. SLC7A3 is highly intolerant to variation in humans, as attested by the low frequency of deleterious variants in available databases, but the impact on variants in this gene in humans remains undefined. In this study, we identified a missense variant in SLC7A3, encoding the CAT-3 cationic amino acid transporter, on chromosome X by exome sequencing in two brothers with autism spectrum disorder (ASD). We then sequenced the SLC7A3 coding sequence in 148 male patients with ASD and identified three additional rare missense variants in unrelated patients. Functional analyses of the mutant transporters showed that two of the four identified variants cause severe or moderate loss of CAT-3 function due to altered protein stability or abnormal trafficking to the plasma membrane. The patient with the most deleterious SLC7A3 variant had high-functioning autism and epilepsy, and also carries a de novo 16p11.2 duplication possibly contributing to his phenotype. This study shows that rare hypomorphic variants of SLC7A3 exist in male individuals and suggest that SLC7A3 variants possibly contribute to the etiology of ASD in male subjects in association with other genetic factors. PMID:26215737

  2. Impacts of simulated acid rain on cation leaching from the Latosol in south China.

    PubMed

    Zhang, Jia-En; Ouyang, Ying; Ling, Da-Jiong

    2007-05-01

    Acid rain is a problem of increasing agricultural, environmental, and ecological concerns worldwide. This study investigated impacts of simulated acid rain (SAR) on cation leaching from the Latosol in south China. Latosol is an acidic red soil and occurs in the tropical rainforest biome. Laboratory experiments were performed by leaching the soil columns with the SAR at a pH range from 2.5 to 7.0 over a 21-day period. A linear increase in effluent K+ concentration was found at the SAR pH 3.0, whereas an exponential decrease in effluent Na+ concentration was observed at all levels of the SAR pH. In general, leaching of Ca2+ and Mg2+ from the Latosol increased as the SAR pH decreased. There was a very good nonlinear correlation between the removal of soil K+ and the SAR pH (R2=0.91), a good nonlinear correlation between the removal of soil Mg+2 and the SAR pH (R2=0.83), a fairly good nonlinear correlation between the removal of soil Ca+2 and the SAR pH (R2=0.56), and no correlation between the removal of soil Na+ and the SAR pH (R2=0.06). Our study further revealed that the removal of soil cations such as K+, Ca+2, and Mg+2 can be quantified by the quadratic polynomial equations. In addition, impacts of the SAR on cation leaching depended not only on the SAR pH but also on the original soil pH.

  3. Biological and surface-active properties of double-chain cationic amino acid-based surfactants.

    PubMed

    Greber, Katarzyna E; Dawgul, Małgorzata; Kamysz, Wojciech; Sawicki, Wiesław; Łukasiak, Jerzy

    2014-08-01

    Cationic amino acid-based surfactants were synthesized via solid phase peptide synthesis and terminal acylation of their α and ε positions with saturated fatty acids. Five new lipopeptides, N-α-acyl-N-ε-acyl lysine analogues, were obtained. Minimum inhibitory concentration and minimum bactericidal (fungicidal) concentration were determined on reference strains of bacteria and fungi to evaluate the antimicrobial activity of the lipopeptides. Toxicity to eukaryotic cells was examined via determination of the haemolytic activities. The surface-active properties of these compounds were evaluated by measuring the surface tension and formation of micelles as a function of concentration in aqueous solution. The cationic surfactants demonstrated diverse antibacterial activities dependent on the length of the fatty acid chain. Gram-negative bacteria and fungi showed a higher resistance than Gram-positive bacterial strains. It was found that the haemolytic activities were also chain length-dependent values. The surface-active properties showed a linear correlation between the alkyl chain length and the critical micelle concentration.

  4. Cationic Mucic Acid Polymer-Based siRNA Delivery Systems.

    PubMed

    Pan, Dorothy W; Davis, Mark E

    2015-08-19

    Nanoparticle (NP) delivery systems for small interfering RNA (siRNA) that have good systemic circulation and high nucleic acid content are highly desired for translation into clinical use. Here, a family of cationic mucic acid-containing polymers is synthesized and shown to assemble with siRNA to form NPs. A cationic mucic acid polymer (cMAP) containing alternating mucic acid and charged monomers is synthesized. When combined with siRNA, cMAP forms NPs that require steric stabilization by poly(ethylene glycol) (PEG) that is attached to the NP surface via a 5-nitrophenylboronic acid linkage (5-nitrophenylboronic acid-PEGm (5-nPBA-PEGm)) to diols on mucic acid in the cMAP in order to inhibit aggregation in biological fluids. As an alternative, cMAP is covalently conjugated with PEG via two methods. First, a copolymer is prepared with alternating cMAP-PEG units that can form loops of PEG on the surface of the formulated siRNA-containing NPs. Second, an mPEG-cMAP-PEGm triblock polymer is synthesized that could lead to a PEG brush configuration on the surface of the formulated siRNA-containing NPs. The copolymer and triblock polymer are able to form stable siRNA-containing NPs without and with the addition of 5-nPBA-PEGm. Five formulations, (i) cMAP with 5-nPBA-PEGm, (ii) cMAP-PEG copolymer both (a) with and (b) without 5-nPBA-PEGm, and (iii) mPEG-cMAP-PEGm triblock polymer both (a) with and (b) without 5-nPBA-PEGm, are used to produce NPs in the 30-40 nm size range, and their circulation times are evaluated in mice using tail vein injections. The mPEG-cMAP-PEGm triblock polymer provides the siRNA-containing NP with the longest circulation time (5-10% of the formulation remains in circulation at 60 min postdosing), even when a portion of the excess cationic components used in the formulation is filtered away prior to injection. A NP formulation using the mPEG-cMAP-PEGm triblock polymer that is free of excess components could contain as much as ca. 30 wt % siRNA. PMID

  5. Transformation of cellulose and its derived carbohydrates into formic and lactic acids catalyzed by vanadyl cations.

    PubMed

    Tang, Zhenchen; Deng, Weiping; Wang, Yanliang; Zhu, Enze; Wan, Xiaoyue; Zhang, Qinghong; Wang, Ye

    2014-06-01

    The transformation of cellulose or cellulose-derived carbohydrates into platform chemicals is the key to establish biomass-based sustainable chemical processes. The systems able to catalyze the conversion of cellulose into key chemicals in water without the consumption of hydrogen are limited. We report that simple vanadyl (VO(2+)) cations catalyze the conversions of cellulose and its monomer, glucose, into lactic acid and formic acid in water. We have discovered an interesting shift of the major product from formic acid to lactic acid on switching the reaction atmosphere from oxygen to nitrogen. Our studies suggest that VO(2+) catalyzes the isomerization of glucose to fructose, the retro-aldol fragmentation of fructose to two trioses, and the isomerization of trioses, which leads to the formation of lactic acid under anaerobic conditions. The oxidative cleavage of C-C bonds in the intermediates caused by the redox conversion of VO2(+)/VO(2+) under aerobic conditions results in formic acid and CO2. We demonstrate that the addition of an alcohol suppresses the formation of CO2 and enhances the formic acid yield significantly to 70-75 %.

  6. Transformation of cellulose and its derived carbohydrates into formic and lactic acids catalyzed by vanadyl cations.

    PubMed

    Tang, Zhenchen; Deng, Weiping; Wang, Yanliang; Zhu, Enze; Wan, Xiaoyue; Zhang, Qinghong; Wang, Ye

    2014-06-01

    The transformation of cellulose or cellulose-derived carbohydrates into platform chemicals is the key to establish biomass-based sustainable chemical processes. The systems able to catalyze the conversion of cellulose into key chemicals in water without the consumption of hydrogen are limited. We report that simple vanadyl (VO(2+)) cations catalyze the conversions of cellulose and its monomer, glucose, into lactic acid and formic acid in water. We have discovered an interesting shift of the major product from formic acid to lactic acid on switching the reaction atmosphere from oxygen to nitrogen. Our studies suggest that VO(2+) catalyzes the isomerization of glucose to fructose, the retro-aldol fragmentation of fructose to two trioses, and the isomerization of trioses, which leads to the formation of lactic acid under anaerobic conditions. The oxidative cleavage of C-C bonds in the intermediates caused by the redox conversion of VO2(+)/VO(2+) under aerobic conditions results in formic acid and CO2. We demonstrate that the addition of an alcohol suppresses the formation of CO2 and enhances the formic acid yield significantly to 70-75 %. PMID:24798653

  7. Delivery of siRNA Using Cationic Liposomes Incorporating Stearic Acid-modified Octa-Arginine.

    PubMed

    Yang, Dongsheng; Li, Yuhuan; Qi, Yuhang; Chen, Yongzhen; Yang, Xuewei; Li, Yujing; Liu, Songcai; Lee, Robert J

    2016-07-01

    Cationic liposomes incorporating stearic acid-modified octa-arginine (StA-R8) were evaluated for survivin small interfering RNA (siRNA) delivery. StA-R8 was synthesized and incorporated into liposomes. The composition of liposomes was optimized. Physicochemical properties, cytotoxicity, cellular uptake and gene silencing activity of the liposomes complexed to survivin siRNA were investigated. The results showed that StA-R8-containing liposomes had reduced cytotoxicity and improved delivery efficiency of siRNA into cancer cells compared with StA-R8 by itself.

  8. Delivery of siRNA Using Cationic Liposomes Incorporating Stearic Acid-modified Octa-Arginine.

    PubMed

    Yang, Dongsheng; Li, Yuhuan; Qi, Yuhang; Chen, Yongzhen; Yang, Xuewei; Li, Yujing; Liu, Songcai; Lee, Robert J

    2016-07-01

    Cationic liposomes incorporating stearic acid-modified octa-arginine (StA-R8) were evaluated for survivin small interfering RNA (siRNA) delivery. StA-R8 was synthesized and incorporated into liposomes. The composition of liposomes was optimized. Physicochemical properties, cytotoxicity, cellular uptake and gene silencing activity of the liposomes complexed to survivin siRNA were investigated. The results showed that StA-R8-containing liposomes had reduced cytotoxicity and improved delivery efficiency of siRNA into cancer cells compared with StA-R8 by itself. PMID:27354583

  9. The use of laboratory-determined ion exchange parameters in the predictive modelling of field-scale major cation migration in groundwater over a 40-year period.

    PubMed

    Carlyle, Harriet F; Tellam, John H; Parker, Karen E

    2004-01-01

    An attempt has been made to estimate quantitatively cation concentration changes as estuary water invades a Triassic Sandstone aquifer in northwest England. Cation exchange capacities and selectivity coefficients for Na(+), K(+), Ca(2+), and Mg(2+) were measured in the laboratory using standard techniques. Selectivity coefficients were also determined using a method involving optimized back-calculation from flushing experiments, thus permitting better representation of field conditions; in all cases, the Gaines-Thomas/constant cation exchange capacity (CEC) model was found to be a reasonable, though not perfect, first description. The exchange parameters interpreted from the laboratory experiments were used in a one-dimensional reactive transport mixing cell model, and predictions compared with field pumping well data (Cl and hardness spanning a period of around 40 years, and full major ion analyses in approximately 1980). The concentration patterns predicted using Gaines-Thomas exchange with calcite equilibrium were similar to the observed patterns, but the concentrations of the divalent ions were significantly overestimated, as were 1980 sulphate concentrations, and 1980 alkalinity concentrations were underestimated. Including representation of sulphate reduction in the estuarine alluvium failed to replicate 1980 HCO(3) and pH values. However, by including partial CO(2) degassing following sulphate reduction, a process for which there is 34S and 18O evidence from a previous study, a good match for SO(4), HCO(3), and pH was attained. Using this modified estuary water and averaged values from the laboratory ion exchange parameter determinations, good predictions for the field cation data were obtained. It is concluded that the Gaines-Thomas/constant exchange capacity model with averaged parameter values can be used successfully in ion exchange predictions in this aquifer at a regional scale and over extended time scales, despite the numerous assumptions inherent in

  10. The use of laboratory-determined ion exchange parameters in the predictive modelling of field-scale major cation migration in groundwater over a 40-year period.

    PubMed

    Carlyle, Harriet F; Tellam, John H; Parker, Karen E

    2004-01-01

    An attempt has been made to estimate quantitatively cation concentration changes as estuary water invades a Triassic Sandstone aquifer in northwest England. Cation exchange capacities and selectivity coefficients for Na(+), K(+), Ca(2+), and Mg(2+) were measured in the laboratory using standard techniques. Selectivity coefficients were also determined using a method involving optimized back-calculation from flushing experiments, thus permitting better representation of field conditions; in all cases, the Gaines-Thomas/constant cation exchange capacity (CEC) model was found to be a reasonable, though not perfect, first description. The exchange parameters interpreted from the laboratory experiments were used in a one-dimensional reactive transport mixing cell model, and predictions compared with field pumping well data (Cl and hardness spanning a period of around 40 years, and full major ion analyses in approximately 1980). The concentration patterns predicted using Gaines-Thomas exchange with calcite equilibrium were similar to the observed patterns, but the concentrations of the divalent ions were significantly overestimated, as were 1980 sulphate concentrations, and 1980 alkalinity concentrations were underestimated. Including representation of sulphate reduction in the estuarine alluvium failed to replicate 1980 HCO(3) and pH values. However, by including partial CO(2) degassing following sulphate reduction, a process for which there is 34S and 18O evidence from a previous study, a good match for SO(4), HCO(3), and pH was attained. Using this modified estuary water and averaged values from the laboratory ion exchange parameter determinations, good predictions for the field cation data were obtained. It is concluded that the Gaines-Thomas/constant exchange capacity model with averaged parameter values can be used successfully in ion exchange predictions in this aquifer at a regional scale and over extended time scales, despite the numerous assumptions inherent in

  11. Root uptake of cationic amino acids by Arabidopsis depends on functional expression of amino acid permease 5.

    PubMed

    Svennerstam, Henrik; Ganeteg, Ulrika; Näsholm, Torgny

    2008-01-01

    * Specific transporters mediate uptake of amino acids by plant roots. Earlier studies have indicated that the lysine histidine transporter 1 and amino acid permease 1 participate in this process, but although plant roots have been shown to absorb cationic amino acids with high affinity, neither of these transporters seems to mediate transport of L-arginine (L-Arg) or L-lysine (L-Lys). * Here, a collection of T-DNA knockout mutants were screened for alterations in Arabidopsis root uptake rates of L-Arg and it was found that only the AAP5 mutant displayed clear phenotypic divergence on high concentrations of L-Arg. A second screen using low concentrations of (15)N-labelled L-Arg in the growth media also identified AAP5 as being involved in L-Arg acquisition. * Momentaneous root uptake of basic amino acids was strongly affected in AAP5 mutant lines, but their uptake of other types of amino acids was only marginally affected. Comparisons of the root uptake characteristics of AAP5 and LHT1 mutants corroborated the hypothesis that the two transporters have distinct affinity spectra in planta. * Root uptake of all tested amino acids, except L-aspartic acid (L-Asp), was significantly affected in double AAP5*LHT1 mutants, suggesting that these two transporters account for a major proportion of roots' uptake of amino acids at low concentrations. PMID:18681934

  12. Isotopically exchangeable Al in coastal lowland acid sulfate soils.

    PubMed

    Yvanes-Giuliani, Yliane A M; Fink, D; Rose, J; Waite, T David; Collins, Richard N

    2016-01-15

    Periodic discharges of high concentrations of aluminium (Al) causing fish kills and other adverse effects occur worldwide in waterways affected by coastal lowland acid sulfate soils (CLASS). The exchangeability - a metal's ability to readily transfer between the soil solid- and solution-phases - of Al in these soils is therefore of particular importance as it has implications for metal transport, plant availability and toxicity to living organisms. In the present study, the concentrations of isotopically exchangeable Al (E values) were measured in 27 CLASS and compared with common salt extractions (i.e. KCl and CuCl2) used to estimate exchangeable soil pools of Al. E values of Al were high in the soils, ranging from 357 to 3040 mg·kg(-1). Exchangeable concentrations estimated using 1 M KCl were consistently lower than measured E values, although a reasonable correlation was obtained between the two values (E=1.68×AlKCl, r(2)=0.66, n=25). The addition of a 0.2 M CuCl2 extraction step improved the 1:1 agreement between extractable and isotopically exchangeable Al concentrations, but lead to significant mobilisation of non-isotopically exchangeable Al in surficial 'organic-rich' CLASS having E values<1000 mg·kg(-1). It was concluded that currently used (i.e. 1 M KCl) methodology severely underestimates exchangeable Al and total actual acidity values in CLASS and should be corrected by a factor similar to the one determined here. PMID:26519574

  13. Millisecond Kinetics of Nanocrystal Cation Exchange UsingMicrofluidic X-ray Absorption Spectroscopy

    SciTech Connect

    Chan, Emory M.; Marcus, Matthew A.; Fakra, Sirine; Elnaggar,Mariam S.; Mathies, Richard A.; Alivisatos, A. Paul

    2007-05-07

    We describe the use of a flow-focusing microfluidic reactorto measure the kinetics of theCdSe-to-Ag2Se nanocrystal cation exchangereaction using micro-X-ray absorption spectroscopy (mu XAS). The smallmicroreactor dimensions facilitate the millisecond mixing of CdSenanocrystal and Ag+ reactant solutions, and the transposition of thereaction time onto spatial coordinates enables the in situ observation ofthe millisecond reaction with mu XAS. XAS spectra show the progression ofCdSe nanocrystals to Ag2Se over the course of 100 ms without the presenceof long-lived intermediates. These results, along with supporting stoppedflow absorption experiments, suggest that this nanocrystal cationexchange reaction is highly efficient and provide insight into how thereaction progresses in individual particles. This experiment illustratesthe value and potential of in situ microfluidic X-ray synchrotrontechniques for detailed studies of the millisecond structuraltransformations of nanoparticles and other solution-phase reactions inwhich diffusive mixing initiates changes in local bond structures oroxidation states.

  14. Lanthanide N,N'-piperazine-bis(methylenephosphonates) (Ln=La, Ce, Nd) that display flexible frameworks, reversible hydration and cation exchange

    SciTech Connect

    Mowat, John P.S.; Groves, John A.; Wharmby, Michael T.; Miller, Stuart R.; Li Yang; Lightfoot, Philip; Wright, Paul A.

    2009-10-15

    Hydrothermal syntheses of lanthanide bisphosphonate metal organic frameworks comprising the light lanthanides lanthanum, cerium and neodymium and N,N'-piperazine bis(methylenephosphonic acid) (H{sub 2}L(1) and its 2-methyl and 2,5-dimethyl derivatives (H{sub 2}L(2) and H{sub 2}L(3)) gives three new structure types. At elevated starting pH (ca. 5 and above) syntheses give 'type I' materials with all metals and acids of the study (MLnLxH{sub 2}O, M=Na, K, Cs; Ln=La, Ce, Nd; x{approx}4: KCeL(1).4H{sub 2}O, C2/c, a=23.5864(2) A, b=12.1186(2) A, c=5.6613(2) A, beta=93.040(2){sup o}). The framework of structure type I shows considerable flexibility as the ligand is changed, due mainly to rotation around the -N-CH{sub 2}- bond of the linker in response to steric considerations. Type I materials demonstrate cation exchange and dehydration and rehydration behaviour. Upon dehydration of KCeL.4H{sub 2}O, the space group changes to P2{sub 1}/n, a=21.8361(12) A, b=9.3519(4) A, c=5.5629(3) A, beta=96.560(4){sup o}, as a result of a change of the piperazine ring from chair to boat configuration. When syntheses are performed at lower pH, two other structure types crystallise. With the 'non-methyl' ligand 1, type II materials result (LnL(1)H{sub 2}L(1).4.5H{sub 2}O: Ln=La, P-1, a=5.7630(13) A, b=10.213(2) A, c=11.649(2) A, alpha=84.242(2){sup o}, beta=89.051(2){sup o}, gamma=82.876(2){sup o}) in which one half of the ligands coordinate via the piperazine nitrogen atoms. With the 2-methyl ligand, structure type III crystallises (LnHL(2).4H{sub 2}O: Ln=Nd, Ce, P2{sub 1}/c, a=5.7540(9) A, b=14.1259(18) A, c=21.156(5) A, beta=90.14(2){sup o}) due to unfavourable steric interactions of the methyl group in structure type II. - Graphical abstract: The lanthanides La, Ce and Nd give a family of metal organic frameworks based on N,N'-piperazinebismethylenephosphonate ligands: these display reversible dehydration, structural flexibility and cation exchange.

  15. Modelling exchange kinetics of copper at the water-aquatic moss (Fontinalis antipyretica) interface: influence of water cationic composition (Ca, Mg, Na and pH).

    PubMed

    Ferreira, Daniel; Ciffroy, Philippe; Tusseau-Vuillemin, Marie-Hélène; Garnier, Cédric; Garnier, Jean-Marie

    2009-02-01

    The present study investigated the effect of water cationic composition (Ca, Mg, Na, pH) on the bioaccumulation and elimination rates of copper by an aquatic moss (Fontinalis antipyretica), under laboratory conditions. For this purpose, mosses were exposed to copper at an environmentally relevant and usually non-toxic concentration (5 microg L(-1)) in natural waters where cationic composition and concentrations were varied. To describe copper bioaccumulation by aquatic mosses, a two-compartment model was the first-order kinetics, was developed and calibrated under a wide range of water cationic composition. Bioaccumulation rates of Cu in mosses were significantly reduced as the concentrations of competitive cations in solution increased. Hence, in hard-water, Ca and Mg cations play a protective role as they compete with Cu2+ ions for the absorption on transport sites at the organism-water interface. Based on the relationships between each major cation concentration and the exchange kinetics on mosses, the binding constants (K(Ci)(BL)) of each competing cations to the biological surfaces were derived. Using the present cationic-dependent kinetic model, it is now feasible to incorporate water cationic composition in the (re)interpretation of bryophytes contamination levels and in the (re)definition of Water Quality Criteria (WQC) as illustrated through two selected examples of biomonitoring programmes. In the framework of future national water quality guidelines revisions, a such flexible and mechanistic biomonitoring tool (integrating the protective effects of competing cations) may greatly improve the ability of regulators to derive site-specific Cu (metal) guidelines for protecting aquatic biota, while limiting the use of conservative assumptions. PMID:19042004

  16. NOVEL CONTINUOUS PH/SALT GRADIENT AND PEPTIDE SCORE FOR STRONG CATION EXCHANGE CHROMATOGRAPHY IN 2D-NANO-LC/MSMS PEPTIDE IDENTIFICATION FOR PROTEOMICS

    EPA Science Inventory

    Tryptic digests of human serum albumin (HSA) and human lung epithelial cell lysates were used as test samples in a novel proteomics study. Peptides were separated and analyzed using 2D-nano-LC/MSMS with strong cation exchange (SCX) and reverse phase (RP) chromatography and contin...

  17. Knockout of multiple arabidopsis Cation/H+ exchangers suggest isoform-specific roles in metal stress response, germinatin and seed mineral nutrition

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cation/H(+) exchangers encoded by CAX genes play an important role in the vacuolar accumulation of metals including Ca(2+) and Mn(2+). Arabidopsis thaliana CAX1 and CAX3 have been previously shown to differ phylogenetically from CAX2 but the physiological roles of these different transporters are st...

  18. Sea cucumber-like hydroxyapatite: cation exchange membrane-assisted synthesis and its application in ultra-sensitive heavy metal detection.

    PubMed

    Zhang, Ying; Liu, Yong; Ji, Xiaobo; Banks, Craig E; Zhang, Wei

    2011-04-14

    Sea cucumber-like hydroxyapatite fabricated with the aid of a Nafion N-117 cation exchange membrane was applied to the detection of lead(II) and cadmium(II) in ultra-trace concentration levels. The proposed HAp-modified carbon paste electrode has significantly lower linear ranges and exhibits a larger sensitivity than those reported previously.

  19. Comparative assessment of the methods for exchangeable acidity measuring

    NASA Astrophysics Data System (ADS)

    Vanchikova, E. V.; Shamrikova, E. V.; Bespyatykh, N. V.; Zaboeva, G. A.; Bobrova, Yu. I.; Kyz"yurova, E. V.; Grishchenko, N. V.

    2016-05-01

    A comparative assessment of the results of measuring the exchangeable acidity and its components by different methods was performed for the main mineral genetic horizons of texturally-differentiated gleyed and nongleyed soddy-podzolic and gley-podzolic soils of the Komi Republic. It was shown that the contents of all the components of exchangeable soil acidity determined by the Russian method (with potassium chloride solution as extractant, c(KCl) = 1 mol/dm3) were significantly higher than those obtained by the international method (with barium chloride solution as extractant, c(BaCl2) = 0.1 mol/dm3). The error of the estimate of the concentration of H+ ions extracted with barium chloride solution equaled 100%, and this allowed only qualitative description of this component of the soil acidity. In the case of the extraction with potassium chloride, the error of measurements was 50%. It was also shown that the use of potentiometric titration suggested by the Russian method overestimates the results of soil acidity measurement caused by the exchangeable metal ions (Al(III), Fe(III), and Mn(II)) in comparison with the atomic emission method.

  20. Extraction and isolation of TPE from other elements on ion exchangers in aqueous and aqueous-organic solutions of phosphoric acid

    SciTech Connect

    Guseva, L.I.; Tikhomirova, G.S.; Stepushkina, V.V.

    1988-07-01

    The behavior of Am-Es and other actinides on anion and cation exchange resins in aqueous and aqueous-organic solutions of phosphoric acid has been studied in a wide range of concentration of various components of the solution. The sorptivity of transplutonium elements (TPE) on anion exchangers from dilute H/sub 3/PO/sub 4/ with a concentration less than or equal to 1 M in presence of organic solvents (alcohols, ketones, etc.) and on cation exchangers from concentrated H/sub 3/PO/sub 4/ has been found to be significant. The possibility of use of phosphoric acid solutions for isolation of TPE from Th, Pa, U, Np, Pu, and Zr and separation of TPE in different oxidation states in presence of a high-purity oxidant has been shown.

  1. Separation of Bk(IV) and Ce(IV) from trivalent transplutonium and rare earth elements on ion exchange resins in solutions of sulfuric acid

    SciTech Connect

    Guseva, L.I.; Stepushkina, V.V.

    1987-11-01

    Th behavior of Am, Cm, Bk, Cf, Es, Ce, Eu, and Pr on an anion exchange resin and a cation exchange resin in a mixture with PbO/sub 2/ was investigated in sulfuric acid solutions. A substantial difference was detected in the distribution coefficients of Bk and Ce, on the one hand, and the remaining transplutonium and rare earth elements, on the other, associated with oxidation of the first two elements to the tetravalent state. Methods are proposed for the concentration and separation of Bk(IV) and Ce(IV) from the other transplutonium and rare earth elements on an anion exchange resin in solution of 0.01-0.25 M H/sub 2/SO/sub 4/ and a cation exchange resin in 0.75-1.0 M H/sub 2/SO/sub 4/.

  2. Separation of Bk(IV) and Ce(IV) from trivalent transplutonium and rare-earth elements on ion exchangers in solutions of sulfuric acid

    SciTech Connect

    Guseva, L.I.; Stepushkina, V.V.

    1988-05-01

    The behavior of Am, Cm, Bk, Cf, Es, Ce, Eu, and Pr on anion exchangers and cation exchangers mixed with PbO/sub 2/ in solutions of sulfuric acid has been investigated. A significant difference between the distribution coefficients of Bk and Ce, on the one hand, and the remaining transplutonium elements and rare-earth elements, on the other hand, which has been attributed to the oxidation of the first two elements to the tetravalent state, has been discovered. Methods for the preconcentration and separation of Bk(IV) and Ce(IV) from the other transplutonium and rare-earth element son anion exchangers in 0.01-0.25 M H/sub 2/SO/sub 4/ solutions and on cation exchangers in 0.75-1.0 M H/sub 2/SO/sub 4/ solutions have been proposed.

  3. Use of petroleum reside for production of ion exchangers

    SciTech Connect

    Pokonova, Y.V.

    1995-03-10

    Weakly acidic commercial cation exchangers with a static exchange capacity of 4.8-6.7 meq{center_dot}{sup -1} and a mechanical strength of 90% have been synthesized from petroleum asphaltites, resorcinol, and furfural.

  4. Exchangeable sodium induced changes in yield, water relation and cation composition of fennel (Foeniculum vulgare Mill).

    PubMed

    Garg, V K; Singh, P K; Pushpangadan, P

    2005-06-01

    A pot experiment was conducted with the objectives to assess the adaptation potential of fennel crop grown at 10, 20, 25, 35 and 40 ESP (exchangeable sodium percentage) levels. Results showed that the rate of seed germination, plant growth including branching pattern, umbels per plant and 1000 test seed weight were adversely affected by sodic soils. Assuming that fifty percent reduction in seed yield and Na+/K+ ratio in leaf tissue as an index of alkali tolerance revealed that fennel was tolerant up to 25 ESP. The cell sap pH and EC reflected optimum osmoticum maintenance to withstand sodicity stress at this level and beyond this leaf water potential decreased (negatively) more to impede water uptake.

  5. Elution profiles of lanthanides with α-hydroxyisobutyric acid by ion exchange chromatography using fine resin.

    PubMed

    Trikha, Rahul; Sharma, Bal Krishan; Sabharwal, Kanwal Nain; Prabhu, Krishan

    2015-11-01

    Experiments were carried out using a strong acid cation exchange resin with a particle size of 75-150 μm, termed as "fine resin" in hydrogen ion form for the elution of individual lanthanides Sm, Eu, Gd, Tb, and Dy that are produced as fission products in the spent nuclear fuel and generated in the effluent during reprocessing of spent nuclear fuel. Batch experiments were carried out to study the effect of concentration of nitric acid on distribution coefficient. The distribution coefficient values for these individual lanthanides were determined in nitric acid medium in the concentration range of 0.01-4.0 N. Uptake of each individual lanthanide by resin was increased with increased nitric acid concentration from 0.01 to 0.5 N and remained similar from 0.5 to 1.0 N and decreased thereafter up to 4.0 N. Column experiments were also carried out using the same resin to study the parameters like pH of the eluent, flow rate, and resin bed height under isocratic elution conditions for eluting lanthanide elements using α-hydroxyisobutyric acid as eluent. The results of this study have indicated the possibility for the elution of individual lanthanides.

  6. Increments to chiral recognition facilitating enantiomer separations of chiral acids, bases, and ampholytes using Cinchona-based zwitterion exchanger chiral stationary phases.

    PubMed

    Wernisch, Stefanie; Pell, Reinhard; Lindner, Wolfgang

    2012-07-01

    The intramolecular distances of anion and cation exchanger sites of zwitterionic chiral stationary phases represent potential tuning sites for enantiomer selectivity. In this contribution, we investigate the influence of alkanesulfonic acid chain length and flexibility on enantiomer separations of chiral acids, bases, and amphoteric molecules for six Cinchona alkaloid-based chiral stationary phases in comparison with structurally related anion and cation exchangers. Employing polar-organic elution conditions, we observed an intramolecular counterion effect for acidic analytes which led to reduced retention times but did not impair enantiomer selectivities. Retention of amphoteric analytes is based on simultaneous double ion pairing of their charged functional groups with the acidic and basic sites of the zwitterionic selectors. A chiral center in the vicinity of the strong cation exchanger site is vital for chiral separations of bases. Sterically demanding side chains are beneficial for separations of free amino acids. Enantioseparations of free (un-derivatized) peptides were particularly successful in stationary phases with straight-chain alkanesulfonic acid sites, pointing to a beneficial influence of more flexible moieties. In addition, we observed pseudo-enantiomeric behavior of quinine and quinidine-derived chiral stationary phases facilitating reversal of elution orders for all analytes.

  7. Chemically modified polymeric resins for separation of cations, organic acids, and small polar moleculea by high performance liquid chromatography

    SciTech Connect

    Morris, J.B.

    1993-07-01

    This thesis is divided into 4 parts: a review, ion chromatography of metal cations on carboxylic resins, separation of hydrophilic organic acids and small polar compounds on macroporous resin columns, and use of eluent modifiers for liquid chromatographic separation of carboxylic acids using conductivity detection.

  8. Design of a fixed-bed ion-exchange process for the treatment of rinse waters generated in the galvanization process using Laminaria hyperborea as natural cation exchanger.

    PubMed

    Mazur, Luciana P; Pozdniakova, Tatiana A; Mayer, Diego A; Boaventura, Rui A R; Vilar, Vítor J P

    2016-03-01

    In this study, the removal of zinc from galvanization wastewaters was performed in a fixed bed column packed with brown macro-algae Laminaria hyperborea, acting as a natural cation exchanger (resin). The rinse wastewater presents a zinc concentration between 9 and 22 mg/L, a high concentration of light metals (mainly Na and Ca), a high conductivity (0.5-1.5 mS/cm) and a low organic content (DOC = 7-15 mg C/L). The zinc speciation diagram showed that approximately 80% of zinc is in the form of Zn(2+) and ≅20% as ZnSO4, considering the effluent matrix. From all operational conditions tested for zinc uptake (17 < bed height<27 cm, 4.5 < flow rate<18.2 BV/h, 0.8 < particle equivalent diameter<2.0 mm), the highest useful capacity (7.1 mg Zn/g algae) was obtained for D/dp = 31, L/D = 11, 9.1 BV/h, τ = 6.4 min, corresponding to a service capacity of 124 BV (endpoint of 2 mg Zn/L). Elution was faster and near to 100% effective using 10 BV of HCl (1 M, 3.0%, 363 g HCl/L of resin), for flow rates higher than 4.5 BV/h. Calcium chloride solution (0.1 M) was selected as the best regenerant, allowing the reuse of the natural resin for more than 3 saturation/elution/regeneration cycles. The best operation conditions were scaled-up and tested in a pre-pilot plant. The scale-up design of the cation exchange process was proposed for the treatment of 2.4 m(3)/day of galvanization wastewater, resulting in an estimated reactants cost of 2.44 €/m(3).

  9. Design of a fixed-bed ion-exchange process for the treatment of rinse waters generated in the galvanization process using Laminaria hyperborea as natural cation exchanger.

    PubMed

    Mazur, Luciana P; Pozdniakova, Tatiana A; Mayer, Diego A; Boaventura, Rui A R; Vilar, Vítor J P

    2016-03-01

    In this study, the removal of zinc from galvanization wastewaters was performed in a fixed bed column packed with brown macro-algae Laminaria hyperborea, acting as a natural cation exchanger (resin). The rinse wastewater presents a zinc concentration between 9 and 22 mg/L, a high concentration of light metals (mainly Na and Ca), a high conductivity (0.5-1.5 mS/cm) and a low organic content (DOC = 7-15 mg C/L). The zinc speciation diagram showed that approximately 80% of zinc is in the form of Zn(2+) and ≅20% as ZnSO4, considering the effluent matrix. From all operational conditions tested for zinc uptake (17 < bed height<27 cm, 4.5 < flow rate<18.2 BV/h, 0.8 < particle equivalent diameter<2.0 mm), the highest useful capacity (7.1 mg Zn/g algae) was obtained for D/dp = 31, L/D = 11, 9.1 BV/h, τ = 6.4 min, corresponding to a service capacity of 124 BV (endpoint of 2 mg Zn/L). Elution was faster and near to 100% effective using 10 BV of HCl (1 M, 3.0%, 363 g HCl/L of resin), for flow rates higher than 4.5 BV/h. Calcium chloride solution (0.1 M) was selected as the best regenerant, allowing the reuse of the natural resin for more than 3 saturation/elution/regeneration cycles. The best operation conditions were scaled-up and tested in a pre-pilot plant. The scale-up design of the cation exchange process was proposed for the treatment of 2.4 m(3)/day of galvanization wastewater, resulting in an estimated reactants cost of 2.44 €/m(3). PMID:26766159

  10. Cation exchange reactions controlling desorption of Sr-90(2+) from coarse-grained contaminated sediments at the Hanford site, Washington

    SciTech Connect

    McKinley, James P.; Zachara, John M.; Smith, Steven C.; Liu, Chongxuan

    2007-01-15

    Nuclear waste that bore 90Sr2+ was accidentally leaked into the vadose zone at the Hanford site, and was immobilized at relatively shallow depths in sediments containing little apparent clay or silt-sized components. Sr2+, 90Sr2+, Mg2+, and Ca2+ was desorbed and total inorganic carbon concentration was monitored during the equilibration of this sediment with varying concentrations of Na+, Ca2+. A cation exchange model previously developed for similar sediments was applied to these results as a predictor of final solution compositions. The model included binary exchange reactions for the four operant cations and an equilibrium dissolution/precipitation reaction for calcite. The model successfully predicted the desorption data. The contaminated sediment was also examined using digital autoradiography, a sensitive tool for imaging the distribution of radioactivity. The exchanger phase containing 90Sr was found to consist of smectite formed from weathering of mesostasis glass in basaltic lithic fragments. These clasts are a significant component of Hanford formation sands. The relatively small but significant cation exchange capacity of these sediments was thus a consequence of reaction with physically sequestered clays in sediment that contained essentially no fine-grained material. The nature of this exchange component explained the relatively slow (scale of days) evolution of desorption solutions. The experimental and model results indicated that there is little risk of migration of 90Sr2+ to the water table.

  11. Ion-exchange equilibrium of N-acetyl-D-neuraminic acid on a strong anionic exchanger.

    PubMed

    Wu, Jinglan; Ke, Xu; Zhang, Xudong; Zhuang, Wei; Zhou, Jingwei; Ying, Hanjie

    2015-09-15

    N-acetyl-D-neuraminic acid (Neu5Ac) is a high value-added product widely applied in the food industry. A suitable equilibrium model is required for purification of Neu5Ac based on ion-exchange chromatography. Hence, the equilibrium uptake of Neu5Ac on a strong anion exchanger, AD-1 was investigated experimentally and theoretically. The uptake of Neu5Ac by the hydroxyl form of the resin occurred primarily by a stoichiometric exchange of Neu5Ac(-) and OH(-). The experimental data showed that the selectivity coefficient for the exchange of Neu5Ac(-) with OH(-) was a non-constant quantity. Subsequently, the Saunders' model, which took into account the dissociation reactions of Neu5Ac and the condition of electroneutrality, was used to correlate the Neu5Ac sorption isotherms at various solution pHs and Neu5Ac concentrations. The model provided an excellent fit to the binary exchange data for Cl(-)/OH(-) and Neu5Ac(-)/OH(-), and an approximate prediction of equilibrium in the ternary system Cl(-)/Neu5Ac(-)/OH(-). This basic information combined with the general mass transfer model could lay the foundation for the prediction of dynamic behavior of fixed bed separation process afterwards.

  12. Separation of Cinchona alkaloids on a novel strong cation-exchange-type chiral stationary phase-comparison with commercially available strong cation exchanger and reversed-phase packing materials.

    PubMed

    Hoffmann, Christian V; Lämmerhofer, Michael; Lindner, Wolfgang

    2009-02-01

    A recently reported chiral strong cation exchanger (cSCX) type stationary phase was investigated for the LC separation of a series of Cinchona alkaloids and synthetic derivatives thereof to test its usefulness as alternative methodology for the separation of those important pharmaceuticals. The cSCX column-packing material was qualitatively compared on the one hand against a commercially available non-enantioselective SCX-material, PolySulfoethyl-A, and, on the other hand, against a modern C18 reversed-phase stationary phase which is commonly employed for Cinchona alkaloid analysis. Both SCX columns showed no pronounced peak-tailing phenomena which typically hamper Cinchona alkaloid RP analysis and require specific optimization. Thus, the cSCX-based assay provided new feasibilities for the separation of the Cinchona alkaloids in polar organic mode as opposed to conventional reversed-phase methodologies. In particular, a method for the simultaneous determination of eight Cinchona alkaloids (quinine, quinidine, cinchonine, cinchonidine, and their corresponding dihydro analogs) using the cSCX column in HPLC has been developed and exemplarily applied to impurity profiling of a commercial alkaloid sample. Furthermore, both SCX materials allowed successful separation of C9-epi and 10,11-didehydro derivatives from their respective educts in an application in synthetic Cinchona alkaloid chemistry. PMID:19107468

  13. ABSORPTION METHOD FOR SEPARATING METAL CATIONS

    DOEpatents

    Tompkins, E.R.; Parker, G.W.

    1959-03-10

    An improved method is presented for the chromatographic separation of fission products wherein a substantial reduction in liquid volume is obtained. The process consists in contacting a solution containing fission products with a body of ion-exchange adsorbent to effect adsorption of fission product cations. The loaded exchange resin is then contacted with a small volume of a carboxylic acid eluant, thereby recovering the fission products. The fission product carrying eluate is acidified without increasing its volume to the volume of the original solution, and the acidified eluate is then used as a feed solution for a smaller body of ion-exchange resin effecting readsorption of the fission product cations.

  14. Selective determination of pharmaceuticals and illicit drugs in wastewaters using a novel strong cation-exchange solid-phase extraction combined with liquid chromatography-tandem mass spectrometry.

    PubMed

    Gilart, Núria; Cormack, P A G; Marcé, Rosa Maria; Fontanals, Núria; Borrull, Francesc

    2014-01-17

    In this study, two materials are presented with strong cation-exchange (SCX) behaviour synthesised by two different approaches and then crushed for their application as sorbents for solid-phase extraction (SPE) to extract a group of pharmaceuticals and illicit drugs selectively from wastewater samples. The first SCX polymer was obtained by copolymerisation of three monomers: 2-acrylamido-2-methylpropane sulphonic acid (AMPSA), 2-hydroxyethyl methacrylate (HEMA) and pentaerythritol triacrylate (PETRA), while the second was obtained by post-modification with sulphuric acid (H2SO4) of a copolymer based on HEMA and divinylbenzene (DVB). After their syntheses, both polymers were evaluated as SPE sorbents, with all parameters affecting SPE being optimised, such as sample pH, washing and elution solvents and volumes. Thanks to the sulphonic groups present in the structure of the polymers, all of the compounds with basic functionalities were retained on the sorbents after the washing step, removing the acidic analytes and other interfering compounds, providing successful results in terms of ion suppression/enhancement (-12% and 21%) when wastewater samples were analysed. However, AMPSA/HEMA/PETRA (20/60/20) failed to retain the analytes after loading wastewater samples (25 or 50mL), decreasing analyte recovery values significantly, whereas the sulphonated HEMA/DVB (50/50) enabled good SPE performance with recovery values between 70% and 98%, except for ranitidine and EDDP (39% and 43%, respectively). Therefore, this polymer was selected for further method validation and quantification of wastewater samples, providing low method detection limits (MDLs) in this matrix (from 2 to 40ngL(-1)). Finally, most of the studied compounds were detected and quantified in wastewater samples, especially atenolol, ranitidine, cocaine and its metabolite benzoylecgonine. PMID:24369996

  15. Multi-cycle recovery of lactoferrin and lactoperoxidase from crude whey using fimbriated high-capacity magnetic cation exchangers and a novel "rotor-stator" high-gradient magnetic separator.

    PubMed

    Brown, Geoffrey N; Müller, Christine; Theodosiou, Eirini; Franzreb, Matthias; Thomas, Owen R T

    2013-06-01

    Cerium (IV) initiated "graft-from" polymerization reactions were employed to convert M-PVA magnetic particles into polyacrylic acid-fimbriated magnetic cation exchange supports displaying ultra-high binding capacity for basic target proteins. The modifications, which were performed at 25 mg and 2.5 g scales, delivered maximum binding capacities (Qmax ) for hen egg white lysozyme in excess of 320 mg g(-1) , combined with sub-micromolar dissociation constants (0.45-0.69 µm) and "tightness of binding" values greater than 49 L g(-1) . Two batches of polyacrylic acid-fimbriated magnetic cation exchangers were combined to form a 5 g pooled batch exhibiting Qmax values for lysozyme, lactoferrin, and lactoperoxidase of 404, 585, and 685 mg g(-1) , respectively. These magnetic cation exchangers were subsequently employed together with a newly designed "rotor-stator" type HGMF rig, in five sequential cycles of recovery of lactoferrin and lactoperoxidase from 2 L batches of a crude sweet bovine whey feedstock. Lactoferrin purification performance was observed to remain relatively constant from one HGMF cycle to the next over the five operating cycles, with yields between 40% and 49% combined with purification and concentration factors of 37- to 46-fold and 1.3- to 1.6-fold, respectively. The far superior multi-cycle HGMF performance seen here compared to that observed in our earlier studies can be directly attributed to the combined use of improved high capacity adsorbents and superior particle resuspension afforded by the new "rotor-stator" HGMS design.

  16. Reversible dissociation and ligand-glutathione exchange reaction in binuclear cationic tetranitrosyl iron complex with penicillamine.

    PubMed

    Syrtsova, Lidia; Sanina, Natalia; Lyssenko, Konstantin; Kabachkov, Evgeniy; Psikha, Boris; Shkondina, Natal'ja; Pokidova, Olesia; Kotelnikov, Alexander; Aldoshin, Sergey

    2014-01-01

    This paper describes a comparative study of the decomposition of two nitrosyl iron complexes (NICs) with penicillamine thiolic ligands [Fe2(SC5H11NO2)2(NO)4]SO4 ·5H2O (I) and glutathione- (GSH-) ligands [Fe2(SC10H17N3O6)2(NO)4]SO4 ·2H2O (II), which spontaneously evolve to NO in aqueous medium. NO formation was measured by a sensor electrode and by spectrophotometric methods by measuring the formation of a hemoglobin- (Hb-) NO complex. The NO evolution reaction rate from (I)  k 1 = (4.6 ± 0.1)·10(-3) s(-1) and the elimination rate constant of the penicillamine ligand k 2 = (1.8 ± 0.2)·10(-3) s(-1) at 25°C in 0.05 M phosphate buffer,  pH 7.0, was calculated using kinetic modeling based on the experimental data. Both reactions are reversible. Spectrophotometry and mass-spectrometry methods have firmly shown that the penicillamine ligand is exchanged for GS(-) during decomposition of 1.5·10(-4) M (I) in the presence of 10(-3) M GSH, with 76% yield in 24 h. As has been established, such behaviour is caused by the resistance of (II) to decomposition due to the higher affinity of iron to GSH in the complex. The discovered reaction may impede S-glutathionylation of the essential enzyme systems in the presence of (I) and is important for metabolism of NIC, connected with its antitumor activity.

  17. Study of bond Elut® Plexa™ PCX cation exchange resin in flow injection column preconcentration system for metal determination by flame atomic absorption spectrometry.

    PubMed

    Anthemidis, Aristidis N; Xidia, Sofia; Giakisikli, Georgia

    2012-08-15

    A simple and sensitive on-line solid-phase extraction methodology for preconcentration and determination of trace amounts of Cd(II), Pd(II) and Cu(II) in natural water samples has been developed using the strong cation exchange capability of Bond Elut(®) Plexa™ PCX polymer resin. Plexa PCX is a mixed-mode sorbent, commercially available in a cartridge format and as far as we know, there is no application into the field of metal determination. The analytes were retained on the resin, eluted with 1 mol L(-1) hydrochloric acid and subsequently directed to FAAS for quantification. The influence of chemical and flow variables which affect the performance of the system have been studied, providing the appropriate conditions for the analysis of real samples. For preconcentration time of 90 s, an enrichment factor of 90, 95 and 95 and a detection limit (3 s) of 0.1, 1.8 and 0.5 μg L(-1) for Cd(II), Pb(II) and Cu(II), respectively were obtained along with a sampling frequency of 30 h(-1). The accuracy of the proposed method was evaluated by analyzing certified reference materials. This procedure was successfully applied for metal determination in environmental and biological samples. PMID:22841064

  18. Combination of aqueous two-phase extraction and cation-exchange chromatography: new strategies for separation and purification of alliin from garlic powder.

    PubMed

    Jiang, Xiu-min; Lu, Yan-min; Tan, Cong-ping; -Liang, Yan; Cui, Bo

    2014-04-15

    In this study, a two-step process combining aqueous two-phase extraction (ATPE) with chromatography was developed for extraction and purification of alliin from garlic powder. The partition coefficient and yield value of alliin in different types of aqueous two-phase system (ATPS) were compared and response surface methodology (RSM) was used for analyzing and optimizing the extraction process. The optimal extraction conditions of 19% (w/w) (NH4)2SO4, 20% (w/w) 1-prpanol, at 30°C, pH 2.35 with 8.54% (w/w) NaCl was chosen based on the higher yield. Compared to the results obtained with the conventional extraction method, this method had an evident advantage on yield (20.4mg/g versus the original yield of 15.0mg/g) and the concentration of alliin in extract solution by ATPE was close to three times of that with conventional extraction. The purification of alliin was carried out with the ammonium form of sulfonic acid cation-exchange resins 001×7. Sample solution with alliin concentration of 1mg/mL was passed through resins and the desorption of alliin was accomplished by water at the flow velocity of 0.5mL/min, 1.5mL/min, respectively. The purity and recovery of alliin after purification were 80% and 76%, respectively. PMID:24657412

  19. Isolation of cross-linked peptides by diagonal strong cation exchange chromatography for protein complex topology studies by peptide fragment fingerprinting from large sequence databases.

    PubMed

    Buncherd, Hansuk; Roseboom, Winfried; Ghavim, Behrad; Du, Weina; de Koning, Leo J; de Koster, Chris G; de Jong, Luitzen

    2014-06-27

    Knowledge of spatial proximity of amino acid residues obtained by chemical cross-linking and mass spectrometric analysis provides information about protein folding, protein-protein interactions and topology of macromolecular assemblies. We show that the use of bis(succinimidyl)-3-azidomethyl glutarate as a cross-linker provides a solution for two major analytical problems of cross-link mapping by peptide fragment fingerprinting (PFF) from complex sequence databases, i.e., low abundance of protease-generated target peptides and lack of knowledge of the masses of linked peptides. Tris(carboxyethyl)phosphine (TCEP) reduces the azido group in cross-linked peptides to an amine group in competition with cleavage of an amide bond formed in the cross-link reaction. TCEP-induced reaction products were separated by diagonal strong cation exchange (SCX) from unmodified peptides. The relation between the sum of the masses of the cleavage products and the mass of the parent cross-linked peptide enables determination of the masses of candidate linked peptides. By reversed phase LC-MS/MS analysis of secondary SCX fractions, we identified several intraprotein and interprotein cross-links in a HeLa cell nuclear extract, aided by software tools supporting PFF from the entire human sequence database. The data provide new information about interacting protein domains, among others from assemblies involved in splicing.

  20. Highly selective inorganic crystalline ion-exchange material for Sr{sup 2+} in acidic solutions

    SciTech Connect

    Nenoff, T.M.; Miller, J.E.; Thoma, S.G.; Trudell, D.E.

    1996-12-01

    We report a novel antimony titanate ion exchange material, stable in highly acidic conditions and selective to strontium against competing cations, with possible applications at Defense Waste Sites. Its development was based on good selectivity for Cs and Sr by the CSTs and literature information on the ion exchange properties of antimony compounds. This new material has been tested for the selective removal of parts per million level concentrations of Sr{sup 2+} ions from solutions with a pH in the range of 1 M HNO{sub 3} tO 5.7 M Na{sup +}/0.6 M OH{sup -} (with the most important results in the highly acidic regimes). This doped titanate has been characterized with an array of techniques, including equilibrium distribution coefficient (K{sub d}) determinations over a wide pH range, power X-ray diffraction, TEM, BET, direct-current plasma (DCP), and thermal analyses. 13 refs., 2 figs., 2 tabs.

  1. Development of high-productivity, strong cation-exchange adsorbers for protein capture by graft polymerization from membranes with different pore sizes

    PubMed Central

    Chenette, Heather C.S.; Robinson, Julie R.; Hobley, Eboni; Husson, Scott M.

    2012-01-01

    This paper describes the surface modification of macroporous membranes using ATRP (atom transfer radical polymerization) to create cation-exchange adsorbers with high protein binding capacity at high product throughput. The work is motivated by the need for a more economical and rapid capture step in downstream processing of protein therapeutics. Membranes with three reported nominal pore sizes (0.2, 0.45, 1.0 μm) were modified with poly(3-sulfopropyl methacrylate, potassium salt) tentacles, to create a high density of protein binding sites. A special formulation was used in which the monomer was protected by a crown ether to enable surface-initiated ATRP of this cationic polyelectrolyte. Success with modification was supported by chemical analysis using Fourier-transform infrared spectroscopy and indirectly by measurement of pure water flux as a function of polymerization time. Uniformity of modification within the membranes was visualized with confocal laser scanning microscopy. Static and dynamic binding capacities were measured using lysozyme protein to allow comparisons with reported performance data for commercial cation-exchange materials. Dynamic binding capacities were measured for flow rates ranging from 13 to 109 column volumes (CV)/min. Results show that this unique ATRP formulation can be used to fabricate cation-exchange membrane adsorbers with dynamic binding capacities as high as 70 mg/mL at a throughput of 100 CV/min and unprecedented productivity of 300 mg/mL/min. PMID:23175597

  2. Cation exchange synthesis of uniform PbSe/PbS core/shell tetra-pods and their use as near-infrared photodetectors.

    PubMed

    Mishra, N; Mukherjee, B; Xing, G; Chakrabortty, S; Guchhait, A; Lim, J Y

    2016-08-01

    In this work we explore the preparation of complex-shaped semiconductor nanostructures composed of different materials via a cationic exchange process in which the cations of the original semiconductor nanostructure are replaced by cations of different metals with preservation of the shape and the anionic framework of the nanocrystals. Utilizing this cation exchange method, we synthesized two new tetrapods for the first time: Cu2-xSe/Cu2-xS and PbSe/PbS, both prepared from CdSe/CdS tetrapods as 'templates'. We also fabricated near-infrared (NIR) photodetectors with a very simple architecture comprising a PbSe/PbS tetrapod layer between two Au electrodes on a glass substrate. When illuminated by a NIR laser, these devices are capable of achieving a responsivity of 11.9 A W(-1) without the use of ligand-exchange processes, thermal annealing or hybrid device architecture. Transient absorption spectroscopy was carried out on these PbSe/PbS tetrapods, the results of which suggest that the branched morphology contributes in part to device performance. Investigation of the charge dynamics of the PbSe/PbS tetrapods revealed an extremely long-lived exciton recombination lifetime of ∼17 ms, which can result in enhanced photoconductive gain. Overall, these heterostructured tetrapods showcase simultaneously the importance of nanoparticle shape, band structure, and surface chemistry in the attainment of NIR photodetection. PMID:27387963

  3. Cation trapping by cellular acidic compartments: Beyond the concept of lysosomotropic drugs

    SciTech Connect

    Marceau, François; Bawolak, Marie-Thérèse; Lodge, Robert; Bouthillier, Johanne; Gagné-Henley, Angélique; Gaudreault, René C.; Morissette, Guillaume

    2012-02-15

    “Lysosomotropic” cationic drugs are known to concentrate in acidic cell compartments due to low retro-diffusion of the protonated molecule (ion trapping); they draw water by an osmotic mechanism, leading to a vacuolar response. Several aspects of this phenomenon were recently reexamined. (1) The proton pump vacuolar (V)-ATPase is the driving force of cationic drug uptake and ensuing vacuolization. In quantitative transport experiments, V-ATPase inhibitors, such as bafilomycin A1, greatly reduced the uptake of cationic drugs and released them in preloaded cells. (2) Pigmented or fluorescent amines are effectively present in a concentrated form in the large vacuoles. (3) Consistent with V-ATPase expression in trans-Golgi, lysosomes and endosomes, a fraction of the vacuoles is consistently labeled with trans-Golgi markers and protein secretion and endocytosis are often inhibited in vacuolar cells. (4) Macroautophagic signaling (accumulation of lipidated and membrane-bound LC3 II) and labeling of the large vacuoles by the autophagy effector LC3 were consistently observed in cells, precisely at incubation periods and amine concentrations that cause vacuolization. Vacuoles also exhibit late endosome/lysosome markers, because they may originate from such organelles or because macroautophagosomes fuse with lysosomes. Autophagosome persistence is likely due to the lack of resolution of autophagy, rather than to nutritional deprivation. (5) Increased lipophilicity decreases the threshold concentration for the vacuolar and autophagic cytopathology, because simple diffusion into cells is limiting. (6) A still unexplained mitotic arrest is consistently observed in cells loaded with amines. An extended recognition of relevant clinical situations is proposed for local or systemic drug administration.

  4. Method development for the separation of monoclonal antibody charge variants in cation exchange chromatography, Part I: salt gradient approach.

    PubMed

    Fekete, Szabolcs; Beck, Alain; Fekete, Jenő; Guillarme, Davy

    2015-01-01

    Ion exchange chromatography (IEX) is a historical technique widely used for the detailed characterization of therapeutic proteins and can be considered as a reference and powerful technique for the qualitative and quantitative evaluation of charge variants. When applying salt gradient IEX approach for monoclonal antibodies (mAbs) characterization, this approach is described as time-consuming to develop and product-specific. The goal of this study was to tackle these two bottle-necks. By modeling the retention of several commercial mAbs and their variants in IEX, we proved that the mobile phase temperature was not relevant for tuning selectivity, while optimal salt gradient program can be easily found based on only two initial gradients of different slopes. Last but not least, the dependence of retention vs. pH being polynomial, three initial runs at different pH were required to optimize mobile phase pH. Finally, only 9h of initial experiments were necessary to simultaneously optimize salt gradient profile and pH in IEX. The data can then be treated with commercial modeling software to find out the optimal conditions to be used, and accuracy of retention times prediction was excellent (less than 1% variation between predicted and experimental values). Second, we also proved that generic IEX conditions can be applied for the characterization of mAbs possessing a wide range of pI, from 6.7 to 9.1. For this purpose, a strong cation exchange column has to be employed at a pH below 6 and using a proportion of NaCl up to 0.2M. Under these conditions, all the mAbs were properly eluted from the column. Therefore, salt gradient CEX can be considered as a generic multi-product approach. PMID:25240157

  5. Preparation, Physicochemical Properties, and Transfection Activities of Tartaric Acid-Based Cationic Lipids as Effective Nonviral Gene Delivery Vectors.

    PubMed

    Wan, Ning; Jia, Yi-Yang; Hou, Yi-Lin; Ma, Xi-Xi; He, Yong-Sheng; Li, Chen; Zhou, Si-Yuan; Zhang, Bang-Le

    2016-07-01

    In this work two novel cationic lipids using natural tartaric acid as linking backbone were synthesized. These cationic lipids were simply constructed by tartaric acid backbone using head group 6-aminocaproic acid and saturated hydrocarbon chains dodecanol (T-C12-AH) or hexadecanol (T-C16-AH). The physicochemical properties, gel electrophoresis, transfection activities, and cytotoxicity of cationic liposomes were tested. The optimum formulation for T-C12-AH and T-C16-AH was at cationic lipid/dioleoylphosphatidylethanolamine (DOPE) molar ratio of 1 : 0.5 and 1 : 2, respectively, and N/P charge molar ratio of 1 : 1 and 1 : 1, respectively. Under optimized conditions, T-C12-AH and T-C16-AH showed effective gene transfection capabilities, superior or comparable to that of commercially available transfecting reagent 3β-[N-(N',N'-dimethylaminoethyl)carbamoyl]cholesterol (DC-Chol) and N-[2,3-dioleoyloxypropyl]-N,N,N-trimethylammonium chloride (DOTAP). The results demonstrated that the two novel tartaric acid-based cationic lipids exhibited low toxicity and efficient transfection performance, offering an excellent prospect as nonviral vectors for gene delivery. PMID:27118165

  6. Acidic pH and divalent cation sensing by PhoQ are dispensable for systemic salmonellae virulence

    PubMed Central

    Hicks, Kevin G; Delbecq, Scott P; Sancho-Vaello, Enea; Blanc, Marie-Pierre; Dove, Katja K; Prost, Lynne R; Daley, Margaret E; Zeth, Kornelius; Klevit, Rachel E; Miller, Samuel I

    2015-01-01

    Salmonella PhoQ is a histidine kinase with a periplasmic sensor domain (PD) that promotes virulence by detecting the macrophage phagosome. PhoQ activity is repressed by divalent cations and induced in environments of acidic pH, limited divalent cations, and cationic antimicrobial peptides (CAMP). Previously, it was unclear which signals are sensed by salmonellae to promote PhoQ-mediated virulence. We defined conformational changes produced in the PhoQ PD on exposure to acidic pH that indicate structural flexibility is induced in α-helices 4 and 5, suggesting this region contributes to pH sensing. Therefore, we engineered a disulfide bond between W104C and A128C in the PhoQ PD that restrains conformational flexibility in α-helices 4 and 5. PhoQW104C-A128C is responsive to CAMP, but is inhibited for activation by acidic pH and divalent cation limitation. phoQW104C-A128C Salmonella enterica Typhimurium is virulent in mice, indicating that acidic pH and divalent cation sensing by PhoQ are dispensable for virulence. DOI: http://dx.doi.org/10.7554/eLife.06792.001 PMID:26002083

  7. Synthesis and characterization of a novel hybrid nano composite cation exchanger poly-o-toluidine Sn(IV) tungstate: Its analytical applications as ion-selective electrode

    NASA Astrophysics Data System (ADS)

    Khan, Asif Ali; Shaheen, Shakeeba

    2013-02-01

    A novel organic-inorganic nano composite cation exchanger poly-o-toluidine Sn(IV) tungstate has been synthesized by incorporation of a polymer material into inorganic precipitate. The material is a class of hybrid ion-exchanger with good ion-exchange properties, reproducibility, stability and good selectivity for heavy metals. The physico-chemical properties of this nano composite material were characterized by using XRD, TGA, FTIR, SEM and TEM. The ion-exchange capacity, pH titrations, elution behavior and chemical stability were also carried out to study ion-exchange properties of the material. Distribution studies for various metal ions revealed that the nano composite is highly selective for Cd(II). An ion-selective membrane electrode was fabricated using this material for the determination of Cd(II) ions in solutions. The analytical utility of this electrode was established by employing it as an indicator electrode in electrometric titrations.

  8. Water-Mediated Differential Binding of Strontium and Cesium Cations in Fulvic Acid.

    PubMed

    Sadhu, Biswajit; Sundararajan, Mahesh; Bandyopadhyay, Tusar

    2015-08-27

    The migration of potentially harmful radionuclides, such as cesium ((137)Cs) and strontium ((90)Sr), in soil is governed by the chemical and biological reactivity of soil components. Soil organic matter (SOM) that can be modeled through fulvic acid (FA) is known to alter the mobility of radionuclide cations, Cs(+) and Sr(2+). Shedding light on the possible interaction mechanisms at the atomic level of these two ions with FA is thus vital to explain their transport behavior and for the design of new ligands for the efficient extraction of radionuclides. Here we have performed molecular dynamics, metadynamics simulations, and density-functional-theory-based calculations to understand the binding mechanism of Sr(2+) and Cs(+) cations with FA. Our studies predict that interaction of Cs(+) to FA is very weak as compared with Sr(2+). While the water-FA interaction is largely responsible for the weak binding of Cs(+) to FA, leading to the outer sphere complexation of the ion with FA, the interaction between Sr(2+) and FA is stronger and thus can surpass the existing secondary nonbonding interaction between coordinated waters and FA, leading to inner sphere complexation of the ion with FA. We also find that entropy plays a dominant role for Cs(+) binding to FA, whereas Sr(2+) binding is an enthalpy-driven process. Our predicted results are found to be in excellent agreement with the available experimental data on complexation of Cs(+) and Sr(2+) with SOM.

  9. Poly(propylacrylic acid) enhances cationic lipid mediated delivery of antisense oligonucleotides

    PubMed Central

    Lee, Li Kim; Williams, Charity L.; Devore, David; Roth, Charles M.

    2008-01-01

    The use of antisense oligodeoxynucleotides (ODNs) to inhibit the expression of specific mRNA targets represents a powerful technology for control of gene expression. Cationic lipids and polymers are frequently used to improve the delivery of ODNs to cells, but the resulting complexes often aggregate, bind to serum components, and are trafficked poorly within cells. We show that the addition of a synthetic, pH-sensitive, membrane-disrupting polyanion, poly(propylacrylic acid) (PPAA), improves the in vitro efficiency of the cationic lipid, DOTAP, with regard to oligonucleotide delivery and antisense activity. In characterization studies, ODN complexation with DOTAP/ODN was maintained even when substantial amounts of PPAA were added. The formulation also exhibited partial protection of phosphodiester oligonucleotides against enzymatic digestion. In Chinese hamster ovary (CHO) cells, incorporation of PPAA in DOTAP/ODN complexes improved two- to threefold the cellular uptake of fluorescently tagged oligonucleotides. DOTAP/ODN complexes containing PPAA also maintained high levels of uptake into cells upon exposure to serum. Addition of PPAA to DOTAP/ODN complexes enhanced the antisense activity (using GFP as the target) over a range of PPAA concentrations in both serum-free, and to a lesser extent, serum-containing media. Thus, PPAA is a useful adjunct that improves the lipid-mediated delivery of oligonucleotides. PMID:16677032

  10. Proteomics-based, multivariate random forest method for prediction of protein separation behavior during cation-exchange chromatography.

    PubMed

    Swanson, Ryan K; Xu, Ruo; Nettleton, Dan; Glatz, Charles E

    2012-08-01

    The most significant cost of recombinant protein production lies in the optimization of the downstream purification methods, mainly due to a lack of knowledge of the separation behavior of the host cell proteins (HCP). To reduce the effort required for purification process development, this work was aimed at modeling the separation behavior of a complex mixture of proteins in cation-exchange chromatography (CEX). With the emergence of molecular pharming as a viable option for the production of recombinant pharmaceutical proteins, the HCP mixture chosen was an extract of corn germ. Aqueous two phase system (ATPS) partitioning followed by two-dimensional electrophoresis (2DE) provided data on isoelectric point, molecular weight and surface hydrophobicity of the extract and step-elution fractions. A multivariate random forest (MVRF) method was then developed using the three characterization variables to predict the elution pattern of individual corn HCP. The MVRF method achieved an average root mean squared error (RMSE) value of 0.0406 (fraction of protein eluted in each CEX elution step) for all the proteins that were characterized, providing evidence for the effectiveness of both the characterization method and the analysis approach for protein purification applications.

  11. Proteomics-based, multivariate random forest method for prediction of protein separation behavior during cation-exchange chromatography.

    PubMed

    Swanson, Ryan K; Xu, Ruo; Nettleton, Dan; Glatz, Charles E

    2012-08-01

    The most significant cost of recombinant protein production lies in the optimization of the downstream purification methods, mainly due to a lack of knowledge of the separation behavior of the host cell proteins (HCP). To reduce the effort required for purification process development, this work was aimed at modeling the separation behavior of a complex mixture of proteins in cation-exchange chromatography (CEX). With the emergence of molecular pharming as a viable option for the production of recombinant pharmaceutical proteins, the HCP mixture chosen was an extract of corn germ. Aqueous two phase system (ATPS) partitioning followed by two-dimensional electrophoresis (2DE) provided data on isoelectric point, molecular weight and surface hydrophobicity of the extract and step-elution fractions. A multivariate random forest (MVRF) method was then developed using the three characterization variables to predict the elution pattern of individual corn HCP. The MVRF method achieved an average root mean squared error (RMSE) value of 0.0406 (fraction of protein eluted in each CEX elution step) for all the proteins that were characterized, providing evidence for the effectiveness of both the characterization method and the analysis approach for protein purification applications. PMID:22748375

  12. Solution-Membrane Equilibrium at Metal-Deposited Cation-Exchange Membranes: Chronopotentiometric Characterization of Metal-Modified Membranes.

    PubMed

    Shahi; Prakash; Ramachandraiah; Rangarajan; Vasudevan

    1999-08-01

    Copper- and lead-deposited interpolymer cationic membranes have been prepared by electroless plating by an ion-exchange method and characterized by chronopotentiometry and cyclic voltammetry. The parameters such as transition time (tau), Itau1/2, the potential drop (E0) across these membranes immediately after the application of constant current (I), and the height of the potential jump (DeltaE) across the membrane at tau have been measured by chronopotentiometry and compared with those of plain membranes. The approximate percentage of metal coverage and the number of ionic sites masked by the deposited metal in terms of NaCl concentration have been estimated from the differences in Itau1/2 values of plain and metal-deposited membranes. The quantity of metal deposited in a unit area of the membrane surface was measured by differential pulse polarography. The oxidation and reduction peak potentials corresponding to Cu(0)/Cu(II) and Pb(0)/Pb(II) couples were identified by cyclic voltammetry at pH 2.8 and 4.5 of 0.2 M CH3COONa-H2SO4. Copyright 1999 Academic Press. PMID:10395776

  13. Cation exchange capacity (Qv) estimation in shaly sand reservoirs: case studies in the Junggar Basin, northwest China

    NASA Astrophysics Data System (ADS)

    Wang, Liang; Mao, Zhi-Qiang; Sun, Zhong-Chun; Luo, Xing-Ping; Deng, Ren-Shuang; Zhang, Ya-Hui; Ren, Bing

    2015-10-01

    Cation exchange capacity (Qv) is a key parameter in resistivity-based water saturation models of shaly sand reservoirs, and the accuracy of Qv calculation is crucial to the prediction of saturations of oil and gas. In this study, a theoretical expression of Qv in terms of shaly sand permeability (Kshaly-sand), total porosity (ϕt), and salinity of formation water (S) is deduced based on the capillary tube model and the physics volume model. Meanwhile, the classical Schlumberger-Doll research (SDR) model has been introduced to estimate Kshaly-sand. On this basis, a novel technique to estimate Qv from nuclear magnetic resonance (NMR) logs is proposed, and the corresponding model is also established, whose model parameters are calibrated by laboratory Qv and NMR measurements of 15 core samples from the Toutunhe formation of the Junggar Basin, northwest China. Based on the experimental data sets, this technique can be extended to reservoir conditions to estimate continuous Qv along the intervals. The processing results of field examples illustrate that the Qv calculated from field NMR logs are consistent with the analyzed results, with the absolute errors within the scope of  ±0.1 mmol cm-3 for the majority of core samples.

  14. Exchange of Silicon by Trivalent Cations of Iron or Aluminium in Calcium Silicate Perovskite

    NASA Astrophysics Data System (ADS)

    Bläß, U. W.; Boffa-Ballaran, T.; Frost, D. J.; Langenhorst, F.; McCammon, C. A.; Seifert, F.; van Aken, P. A.

    2003-04-01

    Based on experiments it is widely accepted that calcium silicate perovskite is an important constituent of the Earth's transition zone and the lower mantle as a host mineral for calcium as well as for trace elements. In addition the incorporation of Fe3+ or Al3+ and the associated creation of oxygen vacancies could lead to drastic changes in physical and structural properties. In other perovskites such effects are well known: In MgSiO3 perovskite the incorporation of even a few percent of these elements strongly affects the elastic and transport properties. At higher concentrations of vacancies ordering may occur, as in the model system Ca(FexTi1-x)O3-x/2, in which a complete ordering of oxygen vacancies in pseudocubic \\{100\\} planes causes the formation of several intermediate phases. Multianvil experiments in the system Ca(FexSi1-x)O3-x/2 were run at several P-T conditions and a buffered oxygen fugacity of Re-ReO2, and have shown that the maximum exchange of silicon by trivalent iron in CaSiO3 - perovskite is limited to 4% at 16 GPa. This probably disordered phase is clearly separated by a solvus from an ordered perovskite phase with the composition Ca(Fe0.4Si0.6)O2.8. No further oxygen deficient perovskites exist at more iron rich compositions, except the endmember CaFeO2.5, which we observed to be stable at less than 5 GPa only. The unique Ca(Fe0.4Si0.6)O2.8 phase could be examined in detail by optical microscopy, X-ray diffraction, M&{uml;o}ssbauer spectroscopy, electron microprobe, transmission electron microscopy and electron energy loss spectroscopy. All observations indicate that the structure can be characterised by oxygen deficient tetrahedral double layers perpendicular to pseudocubic <111> directions, alternating with eight octahedral perovskite layers, which are one half each occupied by silicon and iron. With aluminium an analogous phase exists with the composition Ca(Al0.4Si0.6)O2.8, where a similar diffraction pattern suggests the same type of

  15. Hyponatremic Chloride-depletion Metabolic Alkalosis Successfully Treated with High Cation-gap Amino Acid.

    PubMed

    Ryuge, Akihiro; Matsui, Katsuomi; Shibagaki, Yugo

    2016-01-01

    Chloride (Cl)-depletion alkalosis (CDA) develops due to the loss of Cl-rich body fluid, i.e., vomiting or diuretics use, and is typically treated with a chloride-rich solution such as normal saline (NS). Although NS is one of the most utilized Cl-rich solutions, high cation-gap amino acid (HCG-AA) predominantly comprises Cl and less sodium, making HCG-AA more efficient in correcting CDA. We herein report a case of CDA with chronic hyponatremia after frequent vomiting, which was successfully treated with HCG-AA without overcorrecting hyponatremia or causing hypervolemia. HCG-AA may be more beneficial than NS for treating hyponatremic or hypervolemic metabolic alkalosis. PMID:27374680

  16. Development and validation of S-allyl-L-cysteine in rat plasma using a mixed-mode reversed-phase and cation-exchange LC-ESI-MS/MS method: application to pharmacokinetic studies.

    PubMed

    Lee, Sanghee; Chang, Nae In; Yoo, Miyoung; Choi, Jung Hoon; Shin, Dongbin

    2015-01-01

    S-Allyl-L-cysteine (SAC), the most abundant organosulfur compound derived from garlic, has multifunctional biological activities that occur via different mechanisms. A sensitive, rapid and simple LC-ESI-MS/MS method using a mixed-mode reversed-phase and cation-exchange column containing C18 silica particles and sulfonic acid cation-exchange particles has been developed and validated for the analysis of SAC in rat plasma. The mobile phase was optimized at 2 mM ammonium acetate buffer (pH = 3.5) and acetonitrile (75:25, v/v). The assay utilized 0.6% acetic acid in methanol to achieve simple and rapid deproteinization. Quantification was conducted using multiple reaction monitoring (MRM) of the transitions of m/z 162.0 → 145.0 for SAC. The standard curve for SAC was linear (r(2) ≥ 0.999) over a range from 5 to 2,500 ng/mL. The intra- and interday precision (relative standard deviation) of the method was not >6.0% at three quality control levels. The limit of quantification (LOQ) was 5.0 ng/mL. After being fully validated, the method was successfully applied to the pharmacokinetic monitoring of SAC in rat plasma. PMID:24668040

  17. The adsorption of cationic dye from aqueous solution onto acid-activated andesite.

    PubMed

    Tsai, Wen-Tien; Hsu, Hsin-Chieh; Su, Ting-Yi; Lin, Keng-Yu; Lin, Chien-Ming; Dai, Tzong-Hung

    2007-08-25

    The adsorption of cationic dye (i.e., methylene blue) onto acid-activated andesite in aqueous solution was studied in a batch system with respect to its kinetics as a function of agitation speed, initial adsorbate concentration, pH, and adsorbent mass. It was found that the resulting acid-activated adsorbent possessed a mesoporous structure with BET surface areas at around 60m(2)/g. The surface characterization of acid-activated andesite was also performed using the zeta-potential measurements, indicating that the charge sign on the surface of the andesite should be negative in a wide pH range (i.e., 3-11). Furthermore, a simplified kinetic model, pseudo-second-order, was tested to investigate the adsorption behaviors of methylene blue onto the clay samples treated under different process conditions. It was found that the adsorption process could be well described with the model. The adsorption capacity parameter of the model obtained in the present work was significantly in line with the process parameters.

  18. Cationic mononuclear ruthenium carboxylates as catalyst prototypes for self-induced hydrogenation of carboxylic acids

    PubMed Central

    Naruto, Masayuki; Saito, Susumu

    2015-01-01

    Carboxylic acids are ubiquitous in bio-renewable and petrochemical sources of carbon. Hydrogenation of carboxylic acids to yield alcohols produces water as the only byproduct, and thus represents a possible next generation, sustainable method for the production of these alternative energy carriers/platform chemicals on a large scale. Reported herein are molecular insights into cationic mononuclear ruthenium carboxylates ([Ru(OCOR)]+) as prototypical catalysts for the hydrogenation of carboxylic acids. The substrate-derived coordinated carboxylate was found to function initially as a proton acceptor for the heterolytic cleavage of dihydrogen, and subsequently also as an acceptor for the hydride from [Ru–H]+, which was generated in the first step (self-induced catalysis). The hydrogenation proceeded selectively and at high levels of functional group tolerance, a feature that is challenging to achieve with existing heterogeneous/homogeneous catalyst systems. These fundamental insights are expected to significantly benefit the future development of metal carboxylate-catalysed hydrogenation processes of bio-renewable resources. PMID:26314266

  19. The adsorption of cationic dye from aqueous solution onto acid-activated andesite.

    PubMed

    Tsai, Wen-Tien; Hsu, Hsin-Chieh; Su, Ting-Yi; Lin, Keng-Yu; Lin, Chien-Ming; Dai, Tzong-Hung

    2007-08-25

    The adsorption of cationic dye (i.e., methylene blue) onto acid-activated andesite in aqueous solution was studied in a batch system with respect to its kinetics as a function of agitation speed, initial adsorbate concentration, pH, and adsorbent mass. It was found that the resulting acid-activated adsorbent possessed a mesoporous structure with BET surface areas at around 60m(2)/g. The surface characterization of acid-activated andesite was also performed using the zeta-potential measurements, indicating that the charge sign on the surface of the andesite should be negative in a wide pH range (i.e., 3-11). Furthermore, a simplified kinetic model, pseudo-second-order, was tested to investigate the adsorption behaviors of methylene blue onto the clay samples treated under different process conditions. It was found that the adsorption process could be well described with the model. The adsorption capacity parameter of the model obtained in the present work was significantly in line with the process parameters. PMID:17363150

  20. Cationic liposome-nucleic acid nanoparticle assemblies with applications in gene delivery and gene silencing.

    PubMed

    Majzoub, Ramsey N; Ewert, Kai K; Safinya, Cyrus R

    2016-07-28

    Cationic liposomes (CLs) are synthetic carriers of nucleic acids in gene delivery and gene silencing therapeutics. The introduction will describe the structures of distinct liquid crystalline phases of CL-nucleic acid complexes, which were revealed in earlier synchrotron small-angle X-ray scattering experiments. When mixed with plasmid DNA, CLs containing lipids with distinct shapes spontaneously undergo topological transitions into self-assembled lamellar, inverse hexagonal, and hexagonal CL-DNA phases. CLs containing cubic phase lipids are observed to readily mix with short interfering RNA (siRNA) molecules creating double gyroid CL-siRNA phases for gene silencing. Custom synthesis of multivalent lipids and a range of novel polyethylene glycol (PEG)-lipids with attached targeting ligands and hydrolysable moieties have led to functionalized equilibrium nanoparticles (NPs) optimized for cell targeting, uptake or endosomal escape. Very recent experiments are described with surface-functionalized PEGylated CL-DNA NPs, including fluorescence microscopy colocalization with members of the Rab family of GTPases, which directly reveal interactions with cell membranes and NP pathways. In vitro optimization of CL-DNA and CL-siRNA NPs with relevant primary cancer cells is expected to impact nucleic acid therapeutics in vivo. This article is part of the themed issue 'Soft interfacial materials: from fundamentals to formulation'. PMID:27298431

  1. Study of the release of a microencapsulated acid dye in polyamide dyeing using mixed cationic liposomes.

    PubMed

    de Sousa, Isabel S C; Castanheira, Elisabete M S; Rocha Gomes, Jaime I N; Real Oliveira, M Elisabete C D

    2011-06-01

    The main objective of this work was to increase the retarding effect of the acid dye Telon(®) Blue RR (C.I. Acid Blue 62; DyStar, Frankfurt, Germany) release on polyamide fibres dyeing by encapsulation of the dye in liposomes as an alternative to synthetic auxiliaries, in order to reduce effluent pollution. The retarding effect achieved with the use of mixed cationic liposomes of dioctadecyldimethylammonium bromide (DODAB)/soybean lecithin (containing a 10% molar fraction of DODAB) was better in comparison with either pure soybean lecithin liposomes or synthetic auxiliaries. The retarding effect of liposomes on the dye release was analysed through changes in the absorption and fluorescence spectra of the acid dye at different conditions. The effect of temperature (in the range of 25 °C - 70 °C) on the spectroscopic behaviour of the dye in the absence and in presence of polyamide was also studied, in order to simulate the dyeing conditions. Exhaustion curves obtained in dyeing experiments showed that, below 45 °C, the retarding effect of the mixed liposomes (lecithin/DODAB (9:1)) was similar to that of the auxiliaries, but better than the one of pure lecithin liposomes. At higher temperatures (above 45 °C), the system lecithin/DODAB presents a better performance, achieving a higher final exhaustion level when compared with the commercial leveling agent without losing the smoothing effect of lecithin.

  2. Cationic mononuclear ruthenium carboxylates as catalyst prototypes for self-induced hydrogenation of carboxylic acids.

    PubMed

    Naruto, Masayuki; Saito, Susumu

    2015-01-01

    Carboxylic acids are ubiquitous in bio-renewable and petrochemical sources of carbon. Hydrogenation of carboxylic acids to yield alcohols produces water as the only byproduct, and thus represents a possible next generation, sustainable method for the production of these alternative energy carriers/platform chemicals on a large scale. Reported herein are molecular insights into cationic mononuclear ruthenium carboxylates ([Ru(OCOR)](+)) as prototypical catalysts for the hydrogenation of carboxylic acids. The substrate-derived coordinated carboxylate was found to function initially as a proton acceptor for the heterolytic cleavage of dihydrogen, and subsequently also as an acceptor for the hydride from [Ru-H](+), which was generated in the first step (self-induced catalysis). The hydrogenation proceeded selectively and at high levels of functional group tolerance, a feature that is challenging to achieve with existing heterogeneous/homogeneous catalyst systems. These fundamental insights are expected to significantly benefit the future development of metal carboxylate-catalysed hydrogenation processes of bio-renewable resources. PMID:26314266

  3. Base cation stimulation of mycorrhization and photosynthesis of sugar maple on acid soils are coupled by foliar nutrient dynamics.

    PubMed

    St Clair, Samuel B; Lynch, Jonathan P

    2005-02-01

    The nutritional benefits that mycorrhizal associations provide to plants may be constrained by acidic soil conditions resulting in decreased photosynthetic function. Sugar maple (Acer saccharum) and red maple (Acer rubrum) seedlings were grown on a native acidic (pH 4.1) soil both unamended and amended with base cations (pH 6.2). In a second study a fungicide treatment was included. Foliar nutrition, mycorrhizal colonization, photosynthesis and their relationships were assessed. On the native soil, red maple maintained higher levels of mycorrhizal colonization and photosynthesis than sugar maple but showed little response to base cation amendments. Mycorrhizal colonization and photosynthesis of sugar maple increased significantly in response to base cation amendments. Correlations were observed among mycorrhizal colonization, foliar nutrition and photosynthesis. The fungicide treatment indicated that 50% of the base cation-induced increase in sugar maple photosynthesis was mycorrhiza related. The results suggest that base cation stimulation of mycorrhization and photosynthesis of sugar maple on acid soils are coupled by foliar nutrient dynamics. Red maple exhibits much less sensitivity to these same edaphic conditions.

  4. G protein coupled receptor signaled apoptosis is associated with activation of a cation insensitive acidic endonuclease and intracellular acidification.

    PubMed

    Sharma, K; Srikant, C B

    1998-01-01

    Apoptosis associated oligonucleosomal fragmentation of DNA can result from the activation of endonucleases that exhibit different pH optima and are either sensitive or insensitive to divalent cations. DNA fragmentation due to activation of cation sensitive endonucleases occurs in the absence of a change in intracellular pH whereas intracellular acidification is a feature of apoptosis characterized by activation of cation insensitive acidic endonuclease. We have reported earlier that somatostatin (SST) induced DNA fragmentation and apoptosis is signaled in a receptor subtype selective manner uniquely via human somatostatin receptor subtype 3 (hSSTR3). In the present study we investigated the pH dependence and cation sensitivity of endonuclease induced in hSSTR3 expressing CHO-K1 cells by the SST agonist octreotide (OCT) and its effect on intracellular pH. We show that OCT induced apoptosis is associated with selective stimulation of a divalent cation insensitive acidic endonuclease. The intracellular pH of of cells undergoing OCT induced apoptosis was 0.9 pH units lower than that of control cells. The effect of OCT on endonuclease and pH was inhibited by orthovanadate as well as by pretreatment with pertussis toxin, suggesting that hSSTR3 initiated cytotoxic signaling is protein tyrosine phosphatase mediated and is G protein dependent. These findings suggest that intracellular acidification and activation of acidic endonuclease mediate wild type p53 associated apoptosis signaled by hormones acting via G protein coupled receptors.

  5. Integrated strong cation-exchange hybrid monolith coupled with capillary zone electrophoresis and simultaneous dynamic pH junction for large-volume proteomic analysis by mass spectrometry.

    PubMed

    Zhang, Zhenbin; Sun, Liangliang; Zhu, Guijie; Yan, Xiaojing; Dovichi, Norman J

    2015-06-01

    A sulfonate-silica hybrid strong cation-exchange (SCX) monolith was synthesized at the proximal end of a capillary zone electrophoresis column and used for on-line solid-phase extraction (SPE) sample preconcentration. Sample was prepared in an acidic buffer and deposited onto the SCX-SPE monolith and eluted using a basic buffer. Electrophoresis was performed in an acidic buffer. This combination of buffers results in formation of a dynamic pH junction, which allows use of relatively large elution buffer volume while maintaining peak efficiency and resolution. All experiments were performed with a 50 µm ID capillary, a 1cm long SCX-SPE monolith, a 60cm long separation capillary, and a electrokinetically pumped nanospray interface. The volume of the capillary is 1.1 µL. By loading 21 µL of a 1×10(-7) M angiotensin II solution, an enrichment factor of 3000 compared to standard electrokinetic injection was achieved on this platform while retaining efficient electrophoretic performance (N=44,000 plates). The loading capacity of the sulfonate SCX hybrid monolith was determined to be ~15 pmol by frontal analysis with 10(-5) M angiotensin II. The system was also applied to the analysis of a 10(-4) mg/mL bovine serum albumin tryptic digest; the protein coverage was 12% and 11 peptides were identified. Finally, by loading 5.5 µL of a 10(-3) mg/mL E. coli digest, 109 proteins and 271 peptides were identified in a 20 min separation; the median separation efficiency generated by these peptides was 25,000 theoretical plates.

  6. Monoclonal antibody heterogeneity analysis and deamidation monitoring with high-performance cation-exchange chromatofocusing using simple, two component buffer systems.

    PubMed

    Kang, Xuezhen; Kutzko, Joseph P; Hayes, Michael L; Frey, Douglas D

    2013-03-29

    The use of either a polyampholyte buffer or a simple buffer system for the high-performance cation-exchange chromatofocusing of monoclonal antibodies is demonstrated for the case where the pH gradient is produced entirely inside the column and with no external mixing of buffers. The simple buffer system used was composed of two buffering species, one which becomes adsorbed onto the column packing and one which does not adsorb, together with an adsorbed ion that does not participate in acid-base equilibrium. The method which employs the simple buffer system is capable of producing a gradual pH gradient in the neutral to acidic pH range that can be adjusted by proper selection of the starting and ending pH values for the gradient as well as the buffering species concentration, pKa, and molecular size. By using this approach, variants of representative monoclonal antibodies with isoelectric points of 7.0 or less were separated with high resolution so that the approach can serve as a complementary alternative to isoelectric focusing for characterizing a monoclonal antibody based on differences in the isoelectric points of the variants present. Because the simple buffer system used eliminates the use of polyampholytes, the method is suitable for antibody heterogeneity analysis coupled with mass spectrometry. The method can also be used at the preparative scale to collect highly purified isoelectric variants of an antibody for further study. To illustrate this, a single isoelectric point variant of a monoclonal antibody was collected and used for a stability study under forced deamidation conditions.

  7. Ligand-modified polyelectrolyte-enhanced ultrafiltration with electrostatic attachment of ligands. 2. Use of diethylenetriaminepentaacetic acid/cationic polyelectrolyte mixtures to remove both cations and anions from aqueous streams

    SciTech Connect

    Tuncay, M. Univ. of Oklahoma, Norman, OK ); Christian, S.D.; Tucker, E.E.; Taylor, R.W.; Scamehorn, J.F. )

    1994-12-01

    A mixture of a cationic polyelectrolyte, poly(diallyldimethylammonium chloride) or PDADMAC, and the anionic ligand diethylenetriaminepentaacetic acid (DTPA) can be added to aqueous streams as a water-soluble colloid to bind simultaneously divalent cations, such as Cu[sup 2+] and Pb[sup 2+], and anions, such as CrO[sub 4][sup 2[minus

  8. {sup 1}H and {sup 23}Na MAS NMR spectroscopy of cationic species in CO{sub 2} selective alkaline earth metal porous silicoaluminophosphates prepared via liquid and solid state ion exchange

    SciTech Connect

    Arevalo-Hidalgo, Ana G.; Dugar, Sneha; Fu, Riqiang; Hernandez-Maldonado, Arturo J.

    2012-07-15

    The location of extraframework cations in Sr{sup 2+} and Ba{sup 2+} ion-exchanged SAPO-34 was estimated by means of {sup 1}H and {sup 23}Na MAS NMR spectroscopy and spectral deconvolution. Incorporation of the alkaline earth metal cations onto the SAPO framework was achieved via liquid state ion exchange, coupled partial detemplation/solid-state ion exchange, and combination of both techniques. MAS NMR revealed that the level of ion exchange was limited by the presence of protons and sodium cations near hexagonal prisms (site SI), which are relatively difficult to exchange with the alkaline earth metal due to steric and charge repulsion criteria. In addition, the presence of ammonium cations in the supercages facilitated the exchange of otherwise tenacious hydrogen as corroborated by unit cell compositional data as well as enhanced CO{sub 2} adsorption at low partial pressures. The extraframework ammonium species were produced from partial detemplation of the structure-directing agent employed for the SAPO-34 synthesis, tetraethylammonium. - Graphical abstract: MAS NMR was used to elucidate the position the cationic species in alkaline earth metal exchanged silicoaluminophosphates. These species played a significant role during the ion exchange process and, therefore, the materials ultimate CO{sub 2} adsorption performance. Highlights: Black-Right-Pointing-Pointer Location of extraframework Sr{sup 2+} or Ba{sup 2+} cations was estimated by means of {sup 1}H and {sup 23}Na MAS NMR. Black-Right-Pointing-Pointer Level of Sr{sup 2+} or Ba{sup 2+} ion exchange was limited by the presence of protons and sodium cations. Black-Right-Pointing-Pointer Presence of ammonium cations in the supercages facilitated the exchange. Black-Right-Pointing-Pointer Sr{sup 2+} and Ba{sup 2+} ion exchanged SAPOs are outstanding CO{sub 2} adsorbents.

  9. TACN-based cationic lipids with amino acid backbone and double tails: materials for non-viral gene delivery.

    PubMed

    Wang, Bing; Yi, Wen-Jing; Zhang, Ji; Zhang, Qin-Fang; Xun, Miao-Miao; Yu, Xiao-Qi

    2014-04-01

    Cationic lipids have become an efficient type of non-viral vectors for gene delivery. In this Letter, four cationic lipids containing 1,4,7-triazacyclononane (TACN) headgroup, glutamic/aspartic acid backbone and dioleyl tails were designed and synthesized. The TACN headgroup gives these lipids excellent pH buffering capacities, which were higher than branched 25 kDa PEI. Cationic liposomes prepared from these lipids and DOPE showed good DNA affinity, and full DNA condensation was found at N/P ratio of 3 via agarose gel electrophoresis. The lipoplexes were characterized by dynamic light scattering (DLS) assay, which gave proper particle sizes and zeta-potentials for transfection. In vitro gene transfection results in two cell lines reveal that TAN (with aspartic acid and amide bond in the structure) shows the best transfection efficiency, which is close to commercially available transfection agent Lipofectamine 2000.

  10. Selective enrichment of sulfides, thiols and methylthiophosphates from water samples on metal-loaded cation-exchange materials for gas chromatographic analysis.

    PubMed

    Beiner, K; Popp, P; Wennrich, R

    2002-08-30

    The suitability of using metal-loaded sorbents for solid-phase extraction to enrich organic sulfur compounds from water samples was studied. To test the retention behavior of a number of sulfides, thiols and methylthiophosphates, a cation-exchanger was loaded with various metal ions. The elution behavior of sulfur compounds was investigated with different solvents. A combination of Pb2+-modified cation-exchanger as sorbent and CS2 (1%, v/v) in toluene proved to be the most suitable approach for the given problem. Using GC with a pulsed flame photometric detector yielded detection limits of between 0.6 and 2.9 microg/l. The results showed good reproducibility with relative standard deviations of 2-11%. PMID:12236501

  11. Core-Shell MnSe@Bi2 Se3 Fabricated via a Cation Exchange Method as Novel Nanotheranostics for Multimodal Imaging and Synergistic Thermoradiotherapy.

    PubMed

    Song, Guosheng; Liang, Chao; Gong, Hua; Li, Meifang; Zheng, Xianchuang; Cheng, Liang; Yang, Kai; Jiang, Xiqun; Liu, Zhuang

    2015-10-28

    MnSe@Bi2 Se3 core-shell nanostructures with highly integrated imaging and therapy functions are fabricated by a simple cation exchange method. Using those nanoparticles as a theranostic agent, a promise concept is further demonstrated to enhance conventional radiotherapy by: i) using X-ray absorbing agents to locally concentrate radiation energy and ii) employing near-infrared-light-triggered photothermal therapy to overcome hypoxia-associated radioresistance. PMID:26331476

  12. Controllable conversion of plasmonic Cu2-xS nanoparticles to Au2S by cation exchange and electron beam induced transformation of Cu2-xS-Au2S core/shell nanostructures.

    PubMed

    Wang, Xianliang; Liu, Xin; Zhu, Dewei; Swihart, Mark T

    2014-08-01

    Self-doped Cu2-xS nanocrystals (NCs) were converted into monodisperse Cu2-xS-Au2S NCs of tunable composition, including pure Au2S, by cation exchange. The near-infrared (NIR) localized surface plasmon resonance (LSPR) was dampened and red-shifted with increasing Au content. Cation exchange was accompanied by elimination of cation vacancies and a change in crystal structure. Partially exchanged Cu2-xS-Au2S core/shell structures evolved to dumbbell-like structures under electron irradiation in the transmission electron microscope (TEM).

  13. Unfolding and aggregation of monoclonal antibodies on cation exchange columns: effects of resin type, load buffer, and protein stability.

    PubMed

    Guo, Jing; Carta, Giorgio

    2015-04-01

    The chromatographic behavior of a monoclonal antibody (mAb) that exhibits a pronounced two-peak elution behavior is studied for a range of strong cation exchange resins and with varying load buffer pH and composition. Six stationary phases are considered, including two tentacle-type resins (Fractogel EMD SO3-(M) and Eshmuno S), a resin with grafted polymeric surface extenders (Nuvia S), a resin with a bimodal pore size distribution (POROS HS 50), and two macroporous resins without polymer grafts (Source 30S and UNOsphere Rapid S). The two-peak elution behavior is very pronounced for the tentacle and polymer-grafted resins and for POROS HS 50, but is essentially absent for the two macroporous resins. The extent of this behavior decreases as the buffer pH and concentration increase and, consequently, mAb binding becomes weaker. Replacing sodium with arginine as the buffer counterion, which is expected to decrease the mAb binding strength, nearly completely eliminates the two-peak behavior, while replacing sodium with tetra-n-butylammonium hydroxide, which is expected to increase the mAb binding strength, dramatically exacerbate the effect. As shown by hydrogen-deuterium exchange mass spectrometry (HX-MS), the two-peak elution behavior is related to conformational changes that occur when the mAb binds. These changes result in increased solvent exposure of specific peptides in the Fc-region for either the Fractogel or the Nuvia resin. No significant conformational changes were seen by HX-MS when the mAb was bound to the UNOsphere resin or on the Fractogel resin when arginine was used in lieu of sodium as the load buffer counterion. Experiments with two additional mAbs on the Fractogel resin show that the two-peak elution behavior is dependent on the particular antibody. Circular dichroism suggests that the propensity of different mAbs to either precipitate directly or to form stabilizing intermolecular structures upon exposure to thermal stress can be related to their

  14. Tuning Equilibrium Compositions in Colloidal Cd1-xMnxSe Nanocrystals Using Diffusion Doping and Cation Exchange.

    PubMed

    Barrows, Charles J; Chakraborty, Pradip; Kornowske, Lindsey M; Gamelin, Daniel R

    2016-01-26

    The physical properties of semiconductor nanocrystals can be tuned dramatically via composition control. Here, we report a detailed investigation of the synthesis of high-quality colloidal Cd1-xMnxSe nanocrystals by diffusion doping of preformed CdSe nanocrystals. Until recently, Cd1-xMnxSe nanocrystals proved elusive because of kinetic incompatibilities between Mn(2+) and Cd(2+) chemistries. Diffusion doping allows Cd1-xMnxSe nanocrystals to be prepared under thermodynamic rather than kinetic control, allowing access to broader composition ranges. We now investigate this chemistry as a model system for understanding the characteristics of nanocrystal diffusion doping more deeply. From the present work, a Se(2-)-limited reaction regime is identified, in which Mn(2+) diffusion into CdSe nanocrystals is gated by added Se(2-), and equilibrium compositions are proportional to the amount of added Se(2-). At large added Se(2-) concentrations, a solubility-limited regime is also identified, in which x = xmax = ∼0.31, independent of the amount of added Se(2-). We further demonstrate that Mn(2+) in-diffusion can be reversed by cation exchange with Cd(2+) under exactly the same reaction conditions, purifying Cd1-xMnxSe nanocrystals back to CdSe nanocrystals with fine tunability. These chemistries offer exceptional composition control in Cd1-xMnxSe NCs, providing opportunities for fundamental studies of impurity diffusion in nanocrystals and for development of compositionally tuned nanocrystals with diverse applications ranging from solar energy conversion to spin-based photonics. PMID:26643033

  15. The effect of geometrical presentation of multimodal cation-exchange ligands on selective recognition of hydrophobic regions on protein surfaces.

    PubMed

    Woo, James; Parimal, Siddharth; Brown, Matthew R; Heden, Ryan; Cramer, Steven M

    2015-09-18

    The effects of spatial organization of hydrophobic and charged moieties on multimodal (MM) cation-exchange ligands were examined by studying protein retention behavior on two commercial chromatographic media, Capto™ MMC and Nuvia™ cPrime™. Proteins with extended regions of surface-exposed aliphatic residues were found to have enhanced retention on the Capto MMC system as compared to the Nuvia cPrime resin. The results further indicated that while the Nuvia cPrime ligand had a strong preference for interactions with aromatic groups, the Capto MMC ligand appeared to interact with both aliphatic and aromatic clusters on the protein surfaces. These observations were formalized into a new set of protein surface property descriptors, which quantified the local distribution of electrostatic and hydrophobic potentials as well as distinguishing between aromatic and aliphatic properties. Using these descriptors, high-performing quantitative structure-activity relationship (QSAR) models (R(2)>0.88) were generated for both the Capto MMC and Nuvia cPrime datasets at pH 5 and pH 6. Descriptors of electrostatic properties were generally common across the four models; however both Capto MMC models included descriptors that quantified regions of aliphatic-based hydrophobicity in addition to aromatic descriptors. Retention was generally reduced by lowering the ligand densities on both MM resins. Notably, elution order was largely unaffected by the change in surface density, but smaller and more aliphatic proteins tended to be more affected by this drop in ligand density. This suggests that modulating the exposure, shape and density of the hydrophobic moieties in multimodal chromatographic systems can alter the preference for surface exposed aliphatic or aromatic residues, thus providing an additional dimension for modulating the selectivity of MM protein separation systems. PMID:26292626

  16. Estimation of soil cation exchange capacity using Genetic Expression Programming (GEP) and Multivariate Adaptive Regression Splines (MARS)

    NASA Astrophysics Data System (ADS)

    Emamgolizadeh, S.; Bateni, S. M.; Shahsavani, D.; Ashrafi, T.; Ghorbani, H.

    2015-10-01

    The soil cation exchange capacity (CEC) is one of the main soil chemical properties, which is required in various fields such as environmental and agricultural engineering as well as soil science. In situ measurement of CEC is time consuming and costly. Hence, numerous studies have used traditional regression-based techniques to estimate CEC from more easily measurable soil parameters (e.g., soil texture, organic matter (OM), and pH). However, these models may not be able to adequately capture the complex and highly nonlinear relationship between CEC and its influential soil variables. In this study, Genetic Expression Programming (GEP) and Multivariate Adaptive Regression Splines (MARS) were employed to estimate CEC from more readily measurable soil physical and chemical variables (e.g., OM, clay, and pH) by developing functional relations. The GEP- and MARS-based functional relations were tested at two field sites in Iran. Results showed that GEP and MARS can provide reliable estimates of CEC. Also, it was found that the MARS model (with root-mean-square-error (RMSE) of 0.318 Cmol+ kg-1 and correlation coefficient (R2) of 0.864) generated slightly better results than the GEP model (with RMSE of 0.270 Cmol+ kg-1 and R2 of 0.807). The performance of GEP and MARS models was compared with two existing approaches, namely artificial neural network (ANN) and multiple linear regression (MLR). The comparison indicated that MARS and GEP outperformed the MLP model, but they did not perform as good as ANN. Finally, a sensitivity analysis was conducted to determine the most and the least influential variables affecting CEC. It was found that OM and pH have the most and least significant effect on CEC, respectively.

  17. Evaluation of strong cation exchange versus isoelectric focusing of peptides for multidimensional liquid chromatography-tandem mass spectrometry.

    PubMed

    Slebos, Robbert J C; Brock, Jonathan W C; Winters, Nancy F; Stuart, Sarah R; Martinez, Misti A; Li, Ming; Chambers, Mathew C; Zimmerman, Lisa J; Ham, Amy J; Tabb, David L; Liebler, Daniel C

    2008-12-01

    Shotgun proteome analysis platforms based on multidimensional liquid chromatography-tandem mass spectrometry (LC-MS/MS) provide a powerful means to discover biomarker candidates in tissue specimens. Analysis platforms must balance sensitivity for peptide detection, reproducibility of detected peptide inventories and analytical throughput for protein amounts commonly present in tissue biospecimens (< 100 microg), such that platform stability is sufficient to detect modest changes in complex proteomes. We compared shotgun proteomics platforms by analyzing tryptic digests of whole cell and tissue proteomes using strong cation exchange (SCX) and isoelectric focusing (IEF) separations of peptides prior to LC-MS/MS analysis on a LTQ-Orbitrap hybrid instrument. IEF separations provided superior reproducibility and resolution for peptide fractionation from samples corresponding to both large (100 microg) and small (10 microg) protein inputs. SCX generated more peptide and protein identifications than did IEF with small (10 microg) samples, whereas the two platforms yielded similar numbers of identifications with large (100 microg) samples. In nine replicate analyses of tryptic peptides from 50 microg colon adenocarcinoma protein, overlap in protein detection by the two platforms was 77% of all proteins detected by both methods combined. IEF more quickly approached maximal detection, with 90% of IEF-detectable medium abundance proteins (those detected with a total of 3-4 peptides) detected within three replicate analyses. In contrast, the SCX platform required six replicates to detect 90% of SCX-detectable medium abundance proteins. High reproducibility and efficient resolution of IEF peptide separations make the IEF platform superior to the SCX platform for biomarker discovery via shotgun proteomic analyses of tissue specimens.

  18. How mono-valent cations bend peptide turns and a first-principles database of amino acids and dipeptides

    NASA Astrophysics Data System (ADS)

    Baldauf, Carsten; Ropo, Matti; Blum, Volker; Scheffler, Matthias

    2014-10-01

    In this contribution we detail our efforts to investigate the structural effects of cations binding to peptides and amino acids. We perform first-principles studies employing long-range dispersion-corrected approximate density-functional theory and compare to gas-phase experiments.

  19. A facile route to synthesize CdZnSe core–shell-like alloyed quantum dots via cation exchange reaction in aqueous system

    SciTech Connect

    Sheng, Yingzhuo; Wei, Jumeng; Liu, Bitao; Peng, Lingling

    2014-09-15

    Highlights: • Water-soluble CdZnSe alloyed QDs synthesized by cation exchange reaction. • The as-prepared CdZnSe QDs have fairly good luminescence properties. • The surface defects of obtained QDs were removed due to the alloyed structure. - Abstract: Water-soluble CdZnSe alloyed nanocrystals have been successfully prepared via “green” cation exchange reaction in aqueous system. The X-ray diffraction (XRD) patterns indicate that the as-prepared nanocrystals had high crystallinity and small particle size of 4–5 nm. The absorption spectra of CdZnSe show red shift of 100 nm from 375 to 475 nm. Moreover, the band-gap photoluminescent (PL) emission has a red shift of 50 nm from 430 to 480 nm with the increase of the reaction time. On the basis of the PL properties and transmission electron microscopy (TEM) images, one kind of core–shell-like structure model was proposed, which resulted from the different cation exchange reaction rates. This structure could greatly improve the luminescence properties by the removal of surface defect of quantum dots. This work would support potential applications in optoelectronic devices, and biomedical tags fields.

  20. Relative Order of Sulfuric Acid, Bisulfate, Hydronium, and Cations at the Air-Water Interface.

    PubMed

    Hua, Wei; Verreault, Dominique; Allen, Heather C

    2015-11-01

    Sulfuric acid (H2SO4), bisulfate (HSO4(-)), and sulfate (SO4(2-)) are among the most abundant species in tropospheric and stratospheric aerosols due to high levels of atmospheric SO2 emitted from biomass burning and volcanic eruptions. The air/aqueous interfaces of sulfuric acid and bisulfate solutions play key roles in heterogeneous reactions, acid rain, radiative balance, and polar stratospheric cloud nucleation. Molecular-level knowledge about the interfacial distribution of these inorganic species and their perturbation of water organization facilitates a better understanding of the reactivity and growth of atmospheric aerosols and of the aerosol surface charge, thus shedding light on topics of air pollution, climate change, and thundercloud electrification. Here, the air/aqueous interface of NaHSO4, NH4HSO4, and Mg(HSO4)2 salt solutions as well as H2SO4 and HCl acid solutions are investigated by means of vibrational sum frequency generation (VSFG) and heterodyne-detected (HD) VSFG spectroscopy. VSFG spectra of all acid solutions show higher SFG response in the OH-bonded region relative to neat water, with 1.1 M H2SO4 being more enhanced than 1.1 M HCl. In addition, VSFG spectra of bisulfate salt solutions highly resemble that of the dilute H2SO4 solution (0.26 M) at a comparable pH. HD-VSFG (Im χ((2))) spectra of acid and bisulfate salt solutions further reveal that hydrogen-bonded water molecules are oriented preferentially toward the bulk liquid phase. General agreement between Im χ((2)) spectra of 1.1 M H2SO4 and 1.1 M HCl acid solutions indicate that HSO4(-) ions have a similar surface preference as that of chloride (Cl(-)) ions. By comparing the direction and magnitude of the electric fields arising from the interfacial ion distributions and the concentration of each species, the most reasonable relative surface preference that can be deduced from a simplified model follows the order H3O(+) > HSO4(-) > Na(+), NH4(+), Mg(2+) > SO4(2-). Interestingly

  1. Relative Order of Sulfuric Acid, Bisulfate, Hydronium, and Cations at the Air-Water Interface.

    PubMed

    Hua, Wei; Verreault, Dominique; Allen, Heather C

    2015-11-01

    Sulfuric acid (H2SO4), bisulfate (HSO4(-)), and sulfate (SO4(2-)) are among the most abundant species in tropospheric and stratospheric aerosols due to high levels of atmospheric SO2 emitted from biomass burning and volcanic eruptions. The air/aqueous interfaces of sulfuric acid and bisulfate solutions play key roles in heterogeneous reactions, acid rain, radiative balance, and polar stratospheric cloud nucleation. Molecular-level knowledge about the interfacial distribution of these inorganic species and their perturbation of water organization facilitates a better understanding of the reactivity and growth of atmospheric aerosols and of the aerosol surface charge, thus shedding light on topics of air pollution, climate change, and thundercloud electrification. Here, the air/aqueous interface of NaHSO4, NH4HSO4, and Mg(HSO4)2 salt solutions as well as H2SO4 and HCl acid solutions are investigated by means of vibrational sum frequency generation (VSFG) and heterodyne-detected (HD) VSFG spectroscopy. VSFG spectra of all acid solutions show higher SFG response in the OH-bonded region relative to neat water, with 1.1 M H2SO4 being more enhanced than 1.1 M HCl. In addition, VSFG spectra of bisulfate salt solutions highly resemble that of the dilute H2SO4 solution (0.26 M) at a comparable pH. HD-VSFG (Im χ((2))) spectra of acid and bisulfate salt solutions further reveal that hydrogen-bonded water molecules are oriented preferentially toward the bulk liquid phase. General agreement between Im χ((2)) spectra of 1.1 M H2SO4 and 1.1 M HCl acid solutions indicate that HSO4(-) ions have a similar surface preference as that of chloride (Cl(-)) ions. By comparing the direction and magnitude of the electric fields arising from the interfacial ion distributions and the concentration of each species, the most reasonable relative surface preference that can be deduced from a simplified model follows the order H3O(+) > HSO4(-) > Na(+), NH4(+), Mg(2+) > SO4(2-). Interestingly

  2. Removal of acidic indigo carmine textile dye from aqueous solutions using radiation induced cationic hydrogels.

    PubMed

    Sari, Müfrettin Murat

    2010-01-01

    This study examined the removal of acidic indigo carmine dyes from aqueous solutions using cationic hydrogels. Irradiated hydrogels were investigated as a new sorbent for dye removal from aqueous solution. Poly(N,N-Diethylamino ethyl methacrylate) [poly(DEAEMA)] hydrogels were prepared by radiation polymerisation of N,N-diethylamino ethyl methacrylate [DEAEMA] monomer in the presence of cross-linking agent, ethylene glycol dimethacrylate [EGDMA], and used for the removal of acidic indigo carmine textile dye. The adsorption of dyes was examined using a batch sorption technique. The effects of pH, time and initial dye concentration on the adsorption capacity of hydrogels were investigated. Maximum gelation ratio was 98.2% at irradiation dose of 5.3 kGy. Maximum equilibrium volume swelling, V/V(0), value was 21.3 at pH 2.8. Maximum amount of adsorbed indigo carmine onto hydrogels was 96.7 mg dye/g gel at pH 2.8, 21 h of adsorption time and 120 mg/L initial dye solution. Swelling and adsorption capacity increased with decreasing of pH. Compared with Congo red, amounts of adsorbed indigo carmine are much higher than those of Congo red. Langmuir isotherm model was the best fit for these poly(DEAEMA) hydrogels-indigo carmine systems.

  3. Cation exchange synthesis of uniform PbSe/PbS core/shell tetra-pods and their use as near-infrared photodetectors

    NASA Astrophysics Data System (ADS)

    Mishra, N.; Mukherjee, B.; Xing, G.; Chakrabortty, S.; Guchhait, A.; Lim, J. Y.

    2016-07-01

    In this work we explore the preparation of complex-shaped semiconductor nanostructures composed of different materials via a cationic exchange process in which the cations of the original semiconductor nanostructure are replaced by cations of different metals with preservation of the shape and the anionic framework of the nanocrystals. Utilizing this cation exchange method, we synthesized two new tetrapods for the first time: Cu2-xSe/Cu2-xS and PbSe/PbS, both prepared from CdSe/CdS tetrapods as `templates'. We also fabricated near-infrared (NIR) photodetectors with a very simple architecture comprising a PbSe/PbS tetrapod layer between two Au electrodes on a glass substrate. When illuminated by a NIR laser, these devices are capable of achieving a responsivity of 11.9 A W-1 without the use of ligand-exchange processes, thermal annealing or hybrid device architecture. Transient absorption spectroscopy was carried out on these PbSe/PbS tetrapods, the results of which suggest that the branched morphology contributes in part to device performance. Investigation of the charge dynamics of the PbSe/PbS tetrapods revealed an extremely long-lived exciton recombination lifetime of ~17 ms, which can result in enhanced photoconductive gain. Overall, these heterostructured tetrapods showcase simultaneously the importance of nanoparticle shape, band structure, and surface chemistry in the attainment of NIR photodetection.In this work we explore the preparation of complex-shaped semiconductor nanostructures composed of different materials via a cationic exchange process in which the cations of the original semiconductor nanostructure are replaced by cations of different metals with preservation of the shape and the anionic framework of the nanocrystals. Utilizing this cation exchange method, we synthesized two new tetrapods for the first time: Cu2-xSe/Cu2-xS and PbSe/PbS, both prepared from CdSe/CdS tetrapods as `templates'. We also fabricated near-infrared (NIR) photodetectors

  4. Separation of berkelium (IV) from trivalent transplutonium elements on ion-exchangers in solutions of phosphoric acid

    SciTech Connect

    Guseva, L.I.; Stepushkina, V.V.; Tikhomirova, G.S.

    1985-01-01

    The dependences of Am, Cm, Bk, Cf and Es behavior on anion- and cation-exchangers in solutions of 0.1-8.0 M H/sub 3/PO/sub 4/ on acid concentration and oxidant content in solution (KBrO/sub 3/) or in resin (PbO/sub 2/) have been studied. Significant differences in distribution coefficients of Bk and other transplutonium elements (TPE) have been found that can be explained by Bk oxidation to the tetravalent state. A simple and effective method of Bk (IV) separation from trivalent TPE has been developed. The method was applied to the isolation of isotopes Bk-249 and Bk-250; the purification factor of Bk (IV) from other TPE is 10/sup 4/-10/sub 6/ per cycle. The possibility of Bk separation from bromate and phosphate ions by its sorption on a cation-exchanger from diluted H/sub 3/PO/sub 4/ solutions with subsequent desorption by the mineral acid has been shown. 20 references, 8 figures.

  5. Production of citric acid using its extraction wastewater treated by anaerobic digestion and ion exchange in an integrated citric acid-methane fermentation process.

    PubMed

    Xu, Jian; Chen, Yang-Qiu; Zhang, Hong-Jian; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2014-08-01

    In order to solve the problem of extraction wastewater pollution in citric acid industry, an integrated citric acid-methane fermentation process is proposed in this study. Extraction wastewater was treated by mesophilic anaerobic digestion and then used to make mash for the next batch of citric acid fermentation. The recycling process was done for seven batches. Citric acid production (82.4 g/L on average) decreased by 34.1 % in the recycling batches (2nd-7th) compared with the first batch. And the residual reducing sugar exceeded 40 g/L on average in the recycling batches. Pigment substances, acetic acid, ammonium, and metal ions in anaerobic digestion effluent (ADE) were considered to be the inhibitors, and their effects on the fermentation were studied. Results indicated that ammonium, Na(+) and K(+) in the ADE significantly inhibited citric acid fermentation. Therefore, the ADE was treated by acidic cation exchange resin prior to reuse to make mash for citric acid fermentation. The recycling process was performed for ten batches, and citric acid productions in the recycling batches were 126.6 g/L on average, increasing by 1.7 % compared with the first batch. This process could eliminate extraction wastewater discharge and reduce water resource consumption.

  6. Online coupling of hydrophilic interaction/strong cation exchange/reversed-phase liquid chromatography with porous graphitic carbon liquid chromatography for simultaneous proteomics and N-glycomics analysis.

    PubMed

    Zhao, Yun; Law, Henry C H; Zhang, Zaijun; Lam, Herman C; Quan, Quan; Li, Guohui; Chu, Ivan K

    2015-10-01

    In this study we developed a fully automated three-dimensional (3D) liquid chromatography methodology-comprising hydrophilic interaction separation as the first dimension, strong cation exchange fractionation as the second dimension, and low-pH reversed-phase (RP) separation as the third dimension-in conjunction downstream with additional complementary porous graphitic carbon separation, to capture non-retained hydrophilic analytes, for both shotgun proteomics and N-glycomics analyses. The performance of the 3D system alone was benchmarked through the analysis of the total lysate of Saccharomyces cerevisiae, leading to improved hydrophilic peptide coverage, from which we identified 19% and 24% more proteins and peptides, respectively, relative to those identified from a two-dimensional hydrophilic interaction liquid chromatography and low-pH RP chromatography (HILIC-RP) system over the same mass spectrometric acquisition time; consequently, the 3D platform also provided enhanced proteome and protein coverage. When we applied the integrated technology to analyses of the total lysate of primary cerebellar granule neurons, we characterized a total of 2201 proteins and 16,937 unique peptides for this primary cell line, providing one of its most comprehensive datasets. Our new integrated technology also exhibited excellent performance in the first N-glycomics analysis of cynomolgus monkey plasma; we successfully identified 122 proposed N-glycans and 135 N-glycosylation sites from 122 N-glycoproteins, and confirmed the presence of 38 N-glycolylneuraminic acid-containing N-glycans, a rare occurrence in human plasma, through tandem mass spectrometry for the first time.

  7. Functionalized alkynyl-chlorogermanes: hydrometallation, Ge-Cl bond activation, Ge-H bond formation and chlorine-tert-butyl exchange via a transient germyl cation.

    PubMed

    Honacker, Christian; Qu, Zheng-Wang; Tannert, Jens; Layh, Marcus; Hepp, Alexander; Grimme, Stefan; Uhl, Werner

    2016-04-14

    Treatment of alkynyl-arylchlorogermanes ArylnGe(Cl)(C[triple bond, length as m-dash]C-(t)Bu)3-n (n = 1, 2) with HM(t)Bu2 (M = Al, Ga) yielded mixed Al or Ga alkenyl-alkynylchlorogermanes via hydrometallation reactions. Intramolecular interactions between the Lewis-basic Cl atoms and the Lewis-acidic Al or Ga atoms afforded MCGeCl heterocycles. The endocyclic M-Cl distances were significantly lengthened compared to the starting compounds and indicated Ge-Cl bond activation. Dual hydrometallation succeeded only with HGa(t)Bu2. One Ga atom of the product was involved in a Ga-Cl bond, while the second one had an interaction to a C-H bond of a phenyl group. In two cases treatment of chlorogermanes with two equivalents of HAl(t)Bu2 resulted in hydroalumination of one alkynyl group and formation of unprecedented Ge-H functionalized germanes, Aryl-Ge(H)(C[triple bond, length as m-dash]C-(t)Bu)[C(Al(t)Bu2)[double bond, length as m-dash]C(H)-(t)Bu] (Aryl = mesityl, triisopropylphenyl). The Al atoms of these compounds interacted with the α-C atoms of the alkynyl groups. Ph(Cl)Ge(C[triple bond, length as m-dash]C-(t)Bu)[C(Al(t)Bu2}[double bond, length as m-dash]C(H)-(t)Bu] reacted in an unusual Cl/(t)Bu exchange to yield the tert-butylgermane Ph((t)Bu)Ge(C[triple bond, length as m-dash]C-(t)Bu)[C{Al((t)Bu)(Cl)}[double bond, length as m-dash]C(H)-(t)Bu]. Quantum chemical calculations suggested the formation of a germyl cation as a transient intermediate.

  8. Development and application of a new method to extract bacterial DNA from soil based on separation of bacteria from soil with cation-exchange resin.

    PubMed

    Jacobsen, C S; Rasmussen, O F

    1992-08-01

    A new method for the extraction of bacterial DNA from soil has been developed. Soil samples of 50 g were dispersed, and bacteria were released by use of a cation-exchange resin; subsequently, bacteria were separated from soil particles by low-speed centrifugation and lysed with lysozyme and ionic detergent, and the DNA was then purified by CsCl-ethidium bromide equilibrium density centrifugation. The extracted DNA was of high molecular weight and sufficiently pure for restriction enzyme digestion, DNA-DNA hybridization, and amplification by the polymerase chain reaction. The advantages of the new method are that the separation of bacteria from soil is considerably faster than by repeated blending, more samples can be handled, and furthermore no aerosols are formed during separation. Also, we investigated whether the CsCl-ethidium bromide equilibrium density centrifugation could be replaced by purification using Gene-Clean. However, this method produced DNAs which were insufficiently pure for several types of analysis. The new method was used to study survival of a 2,4-dichlorophenoxyacetic acid (2,4-D)-degrading Pseudomonas cepacia DBO1 (pRO101) in unamended soil and in soil amended with 2,4-D. We found that the degrading strain, irrespective of inoculation level, was able to grow to the same high numbers in soil amended with 2,4-D, while the strain in nonamended soil were maintained at the inoculation level. Detection based on DNA extraction and subsequent dot blot DNA-DNA hybridization was in accordance with detection by plating on selective medium. PMID:16348750

  9. The partitioning of sulfur and chlorine between andesite melts and magmatic volatiles and the exchange coefficients of major cations

    NASA Astrophysics Data System (ADS)

    Zajacz, Zoltán; Candela, Philip A.; Piccoli, Philip M.; Sanchez-Valle, Carmen

    2012-07-01

    Andesite melts were equilibrated with an H-O-S-bearing volatile phase to determine the partition coefficients for S and Cl as a function of melt composition and oxygen fugacity. The experiments were conducted in rapid-quench MHC vessel assemblies at 200 MPa and 1000 °C, and over a range of imposed fO2 between NNO-1.2 and NNO+1.8. High fluid/melt mass ratios (∼15) were employed, allowing precise and accurate partition coefficients to be obtained by mass balance calculations. Chlorine exhibits Henrian behavior at ClO-0.5 activities typical for arc magmas, with D Cl volatile/melt = 1.36 ± 0.06 (1σ) below 0.2 wt.% Cl in the melt; at higher ClO-0.5 activities, D Cl volatile/melt increases linearly to 2.11 ± 0.02 at 1 wt.% Cl in the melt. In the volatile phase: FeCl2 ∼ NaCl > KCl ∼ HCl. The determination of cation exchange coefficients for major cations yielded: K K,Na volatile/melt = 1.23 ± 0.10 (1σ) and ∗K Fe,Na volatile/melt = D Fe volatile/melt / D Na volatile/melt = 1.08 ± 0.16 (1σ). Under these conditions, the concentration of HCl in the vapor is negatively correlated with the (Na + K)/(Al + Fe3+) ratio in the melt. Reduced sulfur (S2-) appears to obey Henry's law in andesite melt-volatile system at fH2S below pyrrhotite saturation. The partition coefficient for S at fO2 = NNO-0.5 correlates negatively with the FeO concentration in the melt, changing from 254 ± 25 at 4.0 wt.% FeO to 88 ± 6 at 7.5 wt.% FeO. Pyrrhotite saturation is reached when approximately 3.2 mol% S is present in the volatile phase at fO2 = NNO-0.5. At the sulfide/sulfate transition, the partition coefficient of S drops from 171 ± 23 to 21 ± 1 at a constant FeO content of ∼6 wt.% in the melt. At fO2 = NNO+1.8, anhydrite saturation is reached at ∼3.3 mol% S present in the volatile phase. Aqueous volatiles exsolving from intermediate to mafic magmas can efficiently extract S, and effect its

  10. Expression Profile of Cationic Amino Acid Transporters in Rats with Endotoxin-Induced Uveitis

    PubMed Central

    Chang, Shu-Wen; Lee, Yi-An; Kao, Tzu-Yun

    2016-01-01

    Purpose. The transcellular arginine transportation via cationic amino acid transporter (CAT) is the rate-limiting step in nitric oxide (NO) synthesis, which is crucial in intraocular inflammation. In this study, CAT isoforms and inducible nitric oxide synthase (iNOS) expression was investigated in endotoxin-induced uveitis (EIU). Methods. EIU was induced in Lewis rats by lipopolysaccharide (LPS) injection. In the treatment group, the rats were injected intraperitoneally with the proteasome inhibitor bortezomib before EIU induction. After 24 hours, leukocyte quantification, NO measurement of the aqueous humor, and histopathological examination were evaluated. The expression of CAT isoforms and iNOS was determined by reverse transcription-polymerase chain reaction, western blotting, and immunofluorescence staining. Nuclear factor-kappa B (NF-κB) binding activity was evaluated by electrophoretic mobility shift assay. The mouse macrophage cell line RAW 264.7 was used to validate the in vivo findings. Results. LPS significantly stimulated iNOS, CAT-2A, and CAT-2B mRNA and protein expression but did not affect CAT-1 in EIU rats and RAW 264.7 cells. Bortezomib attenuated inflammation and inhibited iNOS, CAT-2A, and CAT-2B expression through NF-κB inhibition. Conclusions. CAT-2 and iNOS, but not CAT-1, are specifically involved in EIU. NF-κB is essential in the induction of CAT-2 and iNOS in EIU. PMID:27413255

  11. Quantitative Intracellular Localization of Cationic Lipid-Nucleic Acid Nanoparticles with Fluorescence Microscopy.

    PubMed

    Majzoub, Ramsey N; Ewert, Kai K; Safinya, Cyrus R

    2016-01-01

    Current activity in developing synthetic carriers of nucleic acids (NA) and small molecule drugs for therapeutic applications is unprecedented. One promising class of synthetic vectors for the delivery of therapeutic NA is PEGylated cationic liposome (CL)-NA nanoparticles (NPs). Chemically modified PEG-lipids can be used to surface-functionalize lipid-NA nanoparticles, allowing researchers to design active nanoparticles that can overcome the various intracellular and extracellular barriers to efficient delivery. Optimization of these functionalized vectors requires a comprehensive understanding of their intracellular pathways. In this chapter we present two distinct methods for investigating the intracellular activity of PEGylated CL-NA NPs using quantitative analysis with fluorescence microscopy.The first method, spatial localization, describes how to prepare fluorescently labeled CL-NA NPs, perform fluorescence microscopy and properly analyze the data to measure the intracellular distribution of nanoparticles and fluorescent signal. We provide software which allows data from multiple cells to be averaged together and yield statistically significant results. The second method, fluorescence colocalization, describes how to label endocytic organelles via Rab-GFPs and generate micrographs for software-assisted NP-endocytic marker colocalization measurements. These tools will allow researchers to study the endosomal trafficking of CL-NA NPs which can guide their design and improve their efficiency. PMID:27436314

  12. Near-Infrared Emitting CuInSe2/CuInS2 Dot Core/Rod Shell Heteronanorods by Sequential Cation Exchange

    PubMed Central

    2015-01-01

    The direct synthesis of heteronanocrystals (HNCs) combining different ternary semiconductors is challenging and has not yet been successful. Here, we report a sequential topotactic cation exchange (CE) pathway that yields CuInSe2/CuInS2 dot core/rod shell nanorods with near-infrared luminescence. In our approach, the Cu+ extraction rate is coupled to the In3+ incorporation rate by the use of a stoichiometric trioctylphosphine-InCl3 complex, which fulfills the roles of both In-source and Cu-extracting agent. In this way, Cu+ ions can be extracted by trioctylphosphine ligands only when the In–P bond is broken. This results in readily available In3+ ions at the same surface site from which the Cu+ is extracted, making the process a direct place exchange reaction and shifting the overall energy balance in favor of the CE. Consequently, controlled cation exchange can occur even in large and anisotropic heterostructured nanocrystals with preservation of the size, shape, and heterostructuring of the template NCs into the product NCs. The cation exchange is self-limited, stopping when the ternary core/shell CuInSe2/CuInS2 composition is reached. The method is very versatile, successfully yielding a variety of luminescent CuInX2 (X = S, Se, and Te) quantum dots, nanorods, and HNCs, by using Cd-chalcogenide NCs and HNCs as templates. The approach reported here thus opens up routes toward materials with unprecedented properties, which would otherwise remain inaccessible. PMID:26449673

  13. Insights in understanding aggregate formation and dissociation in cation exchange chromatography for a structurally unstable Fc-fusion protein.

    PubMed

    Chen, Zhiqiang; Huang, Chao; Chennamsetty, Naresh; Xu, Xuankuo; Li, Zheng Jian

    2016-08-19

    Cation-exchange chromatography (CEX) of a structurally unstable Fc-fusion protein exhibited multi-peak elution profile upon a salt-step elution due to protein aggregation during intra-column buffer transition where low pH and high salt coexisted. The protein exhibited a single-peak elution behavior during a pH-step elution; nevertheless, the levels of soluble aggregates (i.e. high molecular weight species, HMW) in the CEX eluate were still found up to 12-fold higher than that for the load material. The amount of the aggregates formed upon the pH-step elution was dependent on column loading with maximum HMW achieved at intermediate loading levels, supporting the hypothesis that the aggregation was the result of both the conformational changes of the bound protein and the solution concentration of the aggregation-susceptible proteins during elution. Factors such as high load pH, short protein/resin contact time, hydrophilic resin surface, and weak ionizable ligand were effective, to some extent, to reduce aggregate formation by improving the structural integrity of the bound protein. An orthogonal technique, differential scanning fluorimetry (DSF) using Sypro Orange dye confirmed that the bound protein exposed more hydrophobic area than the native molecule in free solution, especially in the pH 4-5 range. The Sypro Orange dye study of resin surface property also demonstrated that the poly[styrene-divinylbenzene]-based Poros XS with polyhydroxyl surface coating is more hydrophobic compared to the agarose-based CM Sepharose FF and SP Sepharose FF. The hydrophobic property of Poros XS contributed to stronger interactions with the partially unfolded bound protein and consequently to the higher aggregate levels seen in Poros XS eluate. This work also investigates the aggregation reversibility in CEX eluate where up to 66% of the aggregates were observed to dissociate into native monomers over a period of 120h, and links the aggregate stability to such conditions as resin

  14. A novel cation exchange polymer as a reversed-dispersive solid phase extraction sorbent for the rapid determination of rhodamine B residue in chili powder and chili oil.

    PubMed

    Chen, Dawei; Zhao, Yunfeng; Miao, Hong; Wu, Yongning

    2014-12-29

    This paper presents a new analytical method for the determination of rhodamine B (RB) residue in chili powder and chili oil based on a novel reversed-dispersive solid phase extraction (r-dSPE) and ultra high performance liquid chromatography–high resolution mass spectrometry (UHPLC–HRMS). Chili powder and chili oil samples were first extracted with acetonitrile/water (1:1, v/v) and acetonitrile, respectively. Then, RB from the extract was adsorbed to the polymer cation exchange (PCX) sorbent with the characteristics of ion exchange and reversed-phase retention. Subsequently, the analyte in PCX sorbent was eluted with ammonium hydroxide/methanol (1:99, v/v) through a simple unit device equipped with 1 mL syringe and 0.22 μm nylon syringe filter. All of the samples were analyzed by UHPLC–HRMS/MS on a Waters Acquity BEH C18 column with 0.1% formic acid and 4 mM ammonium formate in water/acetonitrile as the mobile phase with gradient elution. The matrix effect, recovery, and repeatability, within laboratory reproducibility, and the LODs and LOQs of the r-dSPE cleanup method were investigated. The method showed a good linearity (R2 > 0.999) in the ranges of 0.01–1 μg/L and 1–100 μg/L for the analyte. The LODs of RB for chili powder and chili oil samples were 0.5 μg/kg. The average recoveries of RB from the samples spiked at four different concentrations (2, 20, 500 and 5000 μg/kg) were in a range from 76.7 to 104.9%. Results showed that the proposed method was simple, fast, economical and effective for the determination of RB in chili powder and chili oil. Considering the excellent sorptive performance of PCX for RB, further work should be done to evaluate the usefulness of the PCX in r-dSPE for the clean-up and analyses of other trace-level alkaline contaminants. PMID:25498558

  15. Squalamine, a novel cationic steroid, specifically inhibits the brush-border Na+/H+ exchanger isoform NHE3.

    PubMed

    Akhter, S; Nath, S K; Tse, C M; Williams, J; Zasloff, M; Donowitz, M

    1999-01-01

    Squalamine, an endogenous molecule found in the liver and other tissues of Squalus acanthias, has antibiotic properties and causes changes in endothelial cell shape. The latter suggested that its potential targets might include transport proteins that control cell volume or cell shape. The effect of purified squalamine was examined on cloned Na+/H+ exchanger isoforms NHE1, NHE2, and NHE3 stably transfected in PS120 fibroblasts. Squalamine (1-h pretreatment) decreased the maximal velocity of rabbit NHE3 in a concentration-dependent manner (13, 47, and 57% inhibition with 3, 5, and 7 micrograms/ml, respectively) and also increased K'[H+]i. Squalamine did not affect rabbit NHE1 or NHE2 function. The inhibitory effect of squalamine was 1) time dependent, with no effect of immediate addition and maximum effect with 1 h of exposure, and 2) fully reversible. Squalamine pretreatment of the ileum for 60 min inhibited brush-border membrane vesicle Na+/H+ activity by 51%. Further investigation into the mechanism of squalamine's effects showed that squalamine required the COOH-terminal 76 amino acids of NHE3. Squalamine had no cytotoxic effect at the concentrations studied, as indicated by monitoring lactate dehydrogenase release. These results indicate that squalamine 1) is a specific inhibitor of the brush-border NHE isoform NHE3 and not NHE1 or NHE2, 2) acts in a nontoxic and fully reversible manner, and 3) has a delayed effect, indicating that it may influence brush-border Na+/H+ exchanger function indirectly, through an intracellular signaling pathway or by acting as an intracellular modulator. PMID:9886929

  16. Air-Stable and Efficient PbSe Quantum-Dot Solar Cells Based upon ZnSe to PbSe Cation-Exchanged Quantum Dots.

    PubMed

    Kim, Sungwoo; Marshall, Ashley R; Kroupa, Daniel M; Miller, Elisa M; Luther, Joseph M; Jeong, Sohee; Beard, Matthew C

    2015-08-25

    We developed a single step, cation-exchange reaction that produces air-stable PbSe quantum dots (QDs) from ZnSe QDs and PbX2 (X = Cl, Br, or I) precursors. The resulting PbSe QDs are terminated with halide anions and contain residual Zn cations. We characterized the PbSe QDs using UV-vis-NIR absorption, photoluminescence quantum yield spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. Solar cells fabricated from these PbSe QDs obtained an overall best power conversion efficiency of 6.47% at one sun illumination. The solar cell performance without encapsulation remains unchanged for over 50 days in ambient conditions; and after 50 days, the National Renewable Energy Laboratory certification team certified the device at 5.9%.

  17. Ion exchange properties of novel hydrous metal oxide materials

    SciTech Connect

    Gardner, T.J.; McLaughlin, L.I.

    1996-12-31

    Hydrous metal oxide (HMO) materials are inorganic ion exchangers which have many desirable characteristics for catalyst support applications, including high cation exchange capacity, anion exchange capability, high surface area, ease of adjustment of acidity and basicity, bulk or thin film preparation, and similar chemistry for preparation of various transition metal oxides. Cation exchange capacity is engineered into these materials through the uniform incorporation of alkali cations via manipulation of alkoxide chemistry. Specific examples of the effects of Na stoichiometry and the addition of SiO{sub 2} to hydrous titanium oxide (HTO) on ion exchange behavior will be given. Acid titration and cationic metal precursor complex exchange will be used to characterize the ion exchange behavior of these novel materials.

  18. Metal chalcogenide nanoparticle gel networks: Their formation mechanism and application for novel material generation and heavy metal water remediation via cation exchange reactions

    NASA Astrophysics Data System (ADS)

    Palhares, Leticia F.

    The dissertation research is focused on (1) uncovering the mechanism of metal chalcogenide nanoparticle gel formation; (2) extending the cation exchange reaction protocol to zinc sulfide gel networks, with the goal of accessing new aerogel chemistries and understanding the factors that drive the process; and (3) conducting a quantitative analysis of the ability of ZnS aerogels to remove heavy metal ions from aqueous solutions. The mechanism of metal chalcogenide nanoparticle gel formation was investigated using Raman spectroscopy and X-ray Photoelectron Spectroscopy to probe the chemical changes that occur during the gelation process. These techniques suggest that the bonding between the particles in the CdSe nanoparticle gels is due to the oxidation of surface selenide species, forming covalent Se--Se bonds. Treating the gel networks with a suitable reducing agent, such as a thiol, breaks the covalent bond and disperses the gel network. The addition of sodium borohydride, a "pure" reducing agent, also breaks down the gel network, strengthening the hypothesis that the reducing character of the thiols, not their ligation ability, is responsible for the gel network breakdown. UV-Vis spectroscopy, Transmission Electron Microscopy and Powder X-ray Diffraction were used to analyze the particles after successive gelation-dispersion cycles. The primary particle size decreases after repeated oxidation-reduction cycles, due to nanoparticle surface etching. This trend is observed for CdSe and CdS gel networks, allowing for the proposition that the oxidative-reductive mechanism responsible for the formation-dispersion of the gels is general, applying to other metal chalcogenide nanocrystals as well. The cation exchange reaction previously demonstrated for CdSe gels was extended to ZnS gel networks. The exchange occurs under mild reaction conditions (room temperature, methanol solvent) with exchanging ions of different size, charge and mobility (Ag+, Pb2+, Cd2+ , Cu2+). The

  19. Solvation of exchangeable Cu/sup 2 +/ cations by primary alcohols in montmorillonite clay studied by electron spin resonance and electron spin echo modulation spectroscopies

    SciTech Connect

    Brown, D.R.; Kevan, L.

    1988-04-07

    A montmorillonite clay (STx-1), with Mg/sup 2 +/ as the major exchangeable cation and Cu/sup 2 +/ exchanged into 5% of the Mg/sup 2 +/ sites, is used to study the interaction between the exchangeable cations and adsorbed primary alcohols, methanol, ethanol, and 1-propanol, in the clay interlayer region. Electron spin resonance (ESR) shows that, on saturation of the clay with methanol, a freely rotating Cu/sup 2 +/ center is formed in the clay interlayer. Electron spin echo modulation (ESEM) spectroscopy indicates that the center is a four-coordinate Cu/sup 2 +/ solvate, in which the methanol ligands are in a square-planar configuration. On adsorption of ethanol into the interlayer region, a rotationally restricted Cu/sup 2 +/ center is detected. ESEM again indicates a four-coordinate, square-planar solvate, and ESR of oriented clay films reveals that the major symmetry axis of the ethanol-solvated Cu/sup 2 +/ center is perpendicular to the plane of the clay lattice. Similar ESP data are reported for 1-propanol-saturated montmorillonite, and a four-coordinate, square-planar Cu/sup 2 +/ solvate, similar to that described for ethanol, is proposed.

  20. Infrared Spectroscopic Investigation of the Acidic CH Bonds in Cationic n-Alkanes: Pentane, Hexane, and Heptane.

    PubMed

    Xie, Min; Matsuda, Yoshiyuki; Fujii, Asuka

    2016-08-18

    Radical cations of n-alkanes (pentane, hexane, and heptane) in the gas phase are investigated by infrared predissociation spectroscopy with the argon or nitrogen tagging. All-trans and gauche-involving conformers are identified for these cations by comparisons of observed infrared spectra and vibrational simulations. Intense CH stretch bands are observed in the frequency region lower than the normal alkyl CH stretch frequency. These low frequencies and high intensities of the CH stretch bands are caused by the CH bond weakening and the enhanced positive charge of the hydrogen atoms through the delocalization of the σ electron in the CH bonds. These effects of the delocalization of the σ electron result in the enhanced acidity of the CH bonds. The conformation as well as alkyl chain length dependence of the acidity of the CH bonds is demonstrated by the CH stretch frequency shift trend. PMID:27467194

  1. An ion-exchange nanomembrane sensor for detection of nucleic acids using a surface charge inversion phenomenon.

    PubMed

    Senapati, Satyajyoti; Slouka, Zdenek; Shah, Sunny S; Behura, Susanta K; Shi, Zonggao; Stack, M Sharon; Severson, David W; Chang, Hsueh-Chia

    2014-10-15

    We present a novel low-cost biosensor for rapid, sensitive and selective detection of nucleic acids based on an ionic diode feature of an anion exchange nanoporous membrane under DC bias. The ionic diode feature is associated with external surface charge inversion on the positively charged anion exchange nanomembrane upon hybridization of negatively charged nucleic acid molecules to single-stranded oligoprobes functionalized on the membrane surface resulting in the formation of a cation selective monolayer. The resulting bipolar membrane causes a transition from electroconvection-controlled to water-splitting controlled ion conductance, with a large ion current signature that can be used to accurately quantify the hybridized nucleic acids. The platform is capable of distinguishing two base-pair mismatches in a 22-base pairing segment of microRNAs associated with oral cancer, as well as serotype-specific detection of dengue virus. We also show the sensor' capability to selectively capture target nucleic acids from a heterogeneous mixture. The limit of detection is 1 pM for short 27 base target molecules in a 15-min assay. Similar hybridization results are shown for short DNA molecules as well as RNAs from Brucella and Escherichia coli. The versatility and simplicity of this low-cost biosensor should enable point-of-care diagnostics in food, medical and environmental safety markets.

  2. Acid-catalytic decomposition of peracetic acid in the liquid phase

    SciTech Connect

    Kharchuk, V.G.; Kolenko, I.P.; Petrov, L.A.

    1985-12-01

    This paper elucidates the kinetic relationships of peracetic acid (PAA) decomposition in the presence of mineral acids and their heterogeneous analogs, polystyrene-di-vinylbenzene cation-exchangers, differing in physicochemical and morphological parameters. It is shown that the thermal decomposition of PAA in acetic acid is an acid-catalyzed reaction. The controlling step of the reaction is protonation of the substrate with formation of an active intermediate form. Sulfonated cation-exchangers are twice as effective as sulfuric acid in this process. Polystyrene-divinylbenzene sulfonated cation-exchangers can be used with success as acid catalysts in oxidation processes involving PAA, because of their high effectiveness, stability, and availability.

  3. Reactivity of Cations and Zwitterions Formed in Photochemical and Acid-Catalyzed Reactions from m-Hydroxycycloalkyl-Substituted Phenol Derivatives.

    PubMed

    Cindro, Nikola; Antol, Ivana; Mlinarić-Majerski, Kata; Halasz, Ivan; Wan, Peter; Basarić, Nikola

    2015-12-18

    Three m-substituted phenol derivatives, each with a labile benzylic alcohol group and bearing either protoadamantyl 4, homoadamantyl 5, or a cyclohexyl group 6, were synthesized and their thermal acid-catalyzed and photochemical solvolytic reactivity studied, using preparative irradiations, fluorescence measurements, nanosecond laser flash photolysis, and quantum chemical calculations. The choice of m-hydroxy-substitution was driven by the potential for these phenolic systems to generate m-quinone methides on photolysis, which could ultimately drive the excited-state pathway, as opposed to forming simple benzylic carbocations in the corresponding thermal route. Indeed, thermal acid-catalyzed reactions gave the corresponding cations, which undergo rearrangement and elimination from 4, only elimination from 5, and substitution and elimination from 6. On the other hand, upon photoexcitation of 4-6 to S1 in a polar protic solvent, proton dissociation from the phenol, coupled with elimination of the benzylic OH (as hydroxide ion) gave zwitterions (formal m-quinone methides). The zwitterions exhibit reactivity different from the corresponding cations due to a difference in charge distribution, as shown by DFT calculations. Thus, protoadamantyl zwitterion has a less nonclassical character than the corresponding cation, so it does not undergo 1,2-shift of the carbon atom, as observed in the acid-catalyzed reaction. PMID:26595342

  4. Detachable strong cation exchange monolith, integrated with capillary zone electrophoresis and coupled with pH gradient elution, produces improved sensitivity and numbers of peptide identifications during bottom-up analysis of complex proteomes.

    PubMed

    Zhang, Zhenbin; Yan, Xiaojing; Sun, Liangliang; Zhu, Guijie; Dovichi, Norman J

    2015-04-21

    A detachable sulfonate-silica hybrid strong cation-exchange monolith was synthesized in a fused silica capillary, and used for solid phase extraction with online pH gradient elution during capillary zone electrophoresis-tandem mass spectrometry (CZE-MS/MS) proteomic analysis. Tryptic digests were prepared in 50 mM formic acid and loaded onto the strong cation-exchange monolith. Fractions were eluted using a series of buffers with lower concentration but higher pH values than the 50 mM formic acid background electrolyte. This combination of elution and background electrolytes results in both sample stacking and formation of a dynamic pH junction and allows use of relatively large elution buffer volumes while maintaining reasonable peak efficiency and resolution. A series of five pH bumps were applied to elute E. coli tryptic peptides from the monolith, followed by analysis using CZE coupled to an LTQ-Orbitrap Velos mass spectrometer; 799 protein groups and 3381 peptides were identified from 50 ng of the digest in a 2.5 h analysis, which approaches the identification rate for this organism that was obtained with an Orbitrap Fusion. We attribute the improved numbers of peptide and protein identifications to the efficient fractionation by the online pH gradient elution, which decreased the complexity of the sample in each elution step and improved the signal intensity of low abundance peptides. We also performed a comparative analysis using a nanoACQUITY UltraPerformance LCH system. Similar numbers of protein and peptide identifications were produced by the two methods. Protein identifications showed significant overlap between the two methods, whereas peptide identifications were complementary.

  5. A detachable strong cation exchange monolith, integrated with capillary zone electrophoresis and coupled with pH gradient elution, produces improved sensitivity and numbers of peptide identifications during bottom-up analysis of complex proteomes

    PubMed Central

    Zhang, Zhenbin; Yan, Xiaojing; Sun, Liangliang; Zhu, Guijie; Dovichi, Norman J.

    2015-01-01

    A detachable sulfonate-silica hybrid strong cation-exchange monolith was synthesized in a fused silica capillary, and used for solid phase extraction with on-line pH gradient elution during capillary zone electrophoresis-tandem mass spectrometry (CZE-MS/MS) proteomic analysis. Tryptic digests were prepared in 50 mM formic acid and loaded onto the strong cation-exchange monolith. Fractions were eluted using a series of buffers with lower concentration but higher pH values than the 50 mM formic acid background electrolyte. This combination of elution and background electrolytes results in both sample stacking and formation of a dynamic pH junction, and allows use of relatively large elution buffer volumes while maintaining reasonable peak efficiency and resolution. A series of five pH bumps were applied to elute E. coli tryptic peptides from the monolith, followed by analysis using CZE coupled to an LTQ-Orbitrap Velos mass spectrometer; 799 protein groups and 3,381 peptides were identified from 50 ng of the digest in a 2.5 hour analysis, which approaches the identification rate for this organism that was obtained with an Orbitrap Fusion. We attribute the improved numbers of peptide and protein identifications to the efficient fractionation by the on-line pH gradient elution, which decreased the complexity of the sample in each elution step and improved the signal intensity of low abundance peptides. We also performed a comparative analysis using a nanoACQUITY UltraPerformance LCH system. Similar numbers of protein and peptide identifications were produced by the two methods. Protein identifications showed significant overlap between the two methods, whereas peptide identifications were complementary. PMID:25822566

  6. Closed cycle ion exchange method for regenerating acids, bases and salts

    DOEpatents

    Dreyfuss, Robert M.

    1976-01-01

    A method for conducting a chemical reaction in acidic, basic, or neutral solution as required and then regenerating the acid, base, or salt by means of ion exchange in a closed cycle reaction sequence which comprises contacting the spent acid, base, or salt with an ion exchanger, preferably a synthetic organic ion-exchange resin, so selected that the counter ions thereof are ions also produced as a by-product in the closed reaction cycle, and then regenerating the spent ion exchanger by contact with the by-product counter ions. The method is particularly applicable to closed cycle processes for the thermochemical production of hydrogen.

  7. Divalent cations enhance fluoride binding to Streptococcus mutans and Streptococcus sanguinis cells and subsequently inhibit bacterial acid production.

    PubMed

    Domon-Tawaraya, H; Nakajo, K; Washio, J; Ashizawa, T; Ichino, T; Sugawara, H; Fukumoto, S; Takahashi, N

    2013-01-01

    One preventive effect of topical fluoride application is derived from the fact that fluoride can inhibit bacterial acid production. Furthermore, divalent cations such as Ca(2+) and Mg(2+) increase the binding of fluoride to bacterial cells. These findings suggest that exposure of oral bacteria to fluoride in the presence of divalent cations increases fluoride binding to bacterial cells and subsequently enhances fluoride-induced inhibition of bacterial acid production. This study investigated the effects of fluoride exposure (0-20,000 ppm F) in the presence of Ca(2+) or Mg(2+) prior to glucose challenge on pH fall ability by bacterial sugar fermentation, as well as fluoride binding to bacterial cells by exposure to fluoride, and fluoride release from bacterial cells during bacterial sugar fermentation, using caries-related bacteria, Streptococcus mutans and Streptococcus sanguinis. The pH fall by both streptococci was inhibited by exposure to over 250 ppm F in the presence of Ca(2+) (p < 0.01), whereas in the presence of Mg(2+), the pH fall by S. mutans and S. sanguinis was inhibited after exposure to over 250 and 950 ppm F, respectively (p < 0.05). The amounts of fluoride binding to and released from streptococcal cells increased with the concentration of fluoride the cells were exposed to in the presence of Mg(2+), but were high enough even after 250 ppm F exposure in the presence of Ca(2+). The enhanced inhibition of acid production in the presence of divalent cations is probably due to the improved efficiency of fluoride binding to bacterial cells being improved via these divalent cations.

  8. The Effects of Trivalent Lanthanide Cationization on the Electron Transfer Dissociation of Acidic Fibrinopeptide B and its Analogs

    NASA Astrophysics Data System (ADS)

    Commodore, Juliette J.; Cassady, Carolyn J.

    2016-09-01

    Electrospray ionization (ESI) on mixtures of acidic fibrinopeptide B and two peptide analogs with trivalent lanthanide salts generates [M + Met + H]4+, [M + Met]3+, and [M + Met -H]2+, where M = peptide and Met = metal (except radioactive promethium). These ions undergo extensive and highly efficient electron transfer dissociation (ETD) to form metallated and non-metallated c- and z-ions. All metal adducted product ions contain at least two acidic sites, which suggest attachment of the lanthanide cation at the side chains of one or more acidic residues. The three peptides undergo similar fragmentation. ETD on [M + Met + H]4+ leads to cleavage at every residue; the presence of both a metal ion and an extra proton is very effective in promoting sequence-informative fragmentation. Backbone dissociation of [M + Met]3+ is also extensive, although cleavage does not always occur between adjacent glutamic acid residues. For [M + Met - H ]2+, a more limited range of product ions form. All lanthanide metal peptide complexes display similar fragmentation except for europium (Eu). ETD on [M + Eu - H]2+ and [M + Eu]3+ yields a limited amount of peptide backbone cleavage; however, [M + Eu + H]4+ dissociates extensively with cleavage at every residue. With the exception of the results for Eu(III), metallated peptide ion formation by ESI, ETD fragmentation efficiencies, and product ion formation are unaffected by the identity of the lanthanide cation. Adduction with trivalent lanthanide metal ions is a promising tool for sequence analysis of acidic peptides by ETD.

  9. The Effects of Trivalent Lanthanide Cationization on the Electron Transfer Dissociation of Acidic Fibrinopeptide B and its Analogs.

    PubMed

    Commodore, Juliette J; Cassady, Carolyn J

    2016-09-01

    Electrospray ionization (ESI) on mixtures of acidic fibrinopeptide B and two peptide analogs with trivalent lanthanide salts generates [M + Met + H](4+), [M + Met](3+), and [M + Met -H](2+), where M = peptide and Met = metal (except radioactive promethium). These ions undergo extensive and highly efficient electron transfer dissociation (ETD) to form metallated and non-metallated c- and z-ions. All metal adducted product ions contain at least two acidic sites, which suggest attachment of the lanthanide cation at the side chains of one or more acidic residues. The three peptides undergo similar fragmentation. ETD on [M + Met + H](4+) leads to cleavage at every residue; the presence of both a metal ion and an extra proton is very effective in promoting sequence-informative fragmentation. Backbone dissociation of [M + Met](3+) is also extensive, although cleavage does not always occur between adjacent glutamic acid residues. For [M + Met - H ](2+), a more limited range of product ions form. All lanthanide metal peptide complexes display similar fragmentation except for europium (Eu). ETD on [M + Eu - H](2+) and [M + Eu](3+) yields a limited amount of peptide backbone cleavage; however, [M + Eu + H](4+) dissociates extensively with cleavage at every residue. With the exception of the results for Eu(III), metallated peptide ion formation by ESI, ETD fragmentation efficiencies, and product ion formation are unaffected by the identity of the lanthanide cation. Adduction with trivalent lanthanide metal ions is a promising tool for sequence analysis of acidic peptides by ETD. Graphical Abstract ᅟ.

  10. Influence of Murchison or Allende minerals on hydrogen-deuterium exchange of amino acids.

    PubMed

    Lerner, N R

    1995-04-01

    Deuterium-enriched amino acids occur in the Murchison carbonaceous chrondrite. This meteorite underwent a period of aqueous alteration with isotopically light water. With the objective of setting limits on the conditions of aqueous alteration, the exchange of the carbon-bonded hydrogen atoms of amino acids with D2O has been studied from 295 to 380 K as a function of time and meteorite/heavy water ratio. The amount of Murchison or Allende dust present has a significant effect on the rate and amount of hydrogen-deuterium exchange observed. At elevated temperatures, the alpha-hydrogens of all the amino acids studied were found to exchange with deuterium. In glycine and aspartic acid, this process resulted in total exchange of the carbon-bonded hydrogen. A completely deuterated isotopomer of alanine was produced in significant quantities only when the rock/water ratio was greater than 0.5. No exchange of carbon-bonded hydrogens was observed in the case of amino acids which do not possess an alpha-hydrogen atom. The rates of H/D exchange for amino acids observed here did not correspond to deuterium enrichment of the amino acids in the Murchison meteorite. These results suggest that H/D exchange with water had a negligible effect on the observed deuterium enrichment of amino acids found in Murchison and that the temperature at which the amino acids were exposed to liquid water was close to 273 K.

  11. Separation of thorium and uranium in nitric acid solution using silica based anion exchange resin.

    PubMed

    Chen, Yanliang; Wei, Yuezhou; He, Linfeng; Tang, Fangdong

    2016-09-30

    To separate thorium and uranium in nitric acid solution using anion exchange process, a strong base silica-based anion exchange resin (SiPyR-N4) was synthesized. Batch experiments were conducted and the separation factor of thorium and uranium in 9M nitric acid was about 10. Ion exchange chromatography was applied to separate thorium and uranium in different ratios. Uranium could be eluted by 9M nitric acid and thorium was eluted by 0.1M nitric acid. It was proved that thorium and uranium can be separated and recovered successfully by this method.

  12. Separation of thorium and uranium in nitric acid solution using silica based anion exchange resin.

    PubMed

    Chen, Yanliang; Wei, Yuezhou; He, Linfeng; Tang, Fangdong

    2016-09-30

    To separate thorium and uranium in nitric acid solution using anion exchange process, a strong base silica-based anion exchange resin (SiPyR-N4) was synthesized. Batch experiments were conducted and the separation factor of thorium and uranium in 9M nitric acid was about 10. Ion exchange chromatography was applied to separate thorium and uranium in different ratios. Uranium could be eluted by 9M nitric acid and thorium was eluted by 0.1M nitric acid. It was proved that thorium and uranium can be separated and recovered successfully by this method. PMID:27614730

  13. Tandem anion and cation exchange solid phase extraction for the enrichment of micropollutants and their transformation products from ozonation in a wastewater treatment plant.

    PubMed

    Deeb, Ahmad A; Schmidt, Torsten C

    2016-06-01

    The presence of organic micropollutants and their transformation products (TPs) from biotic and abiotic processes in aquatic environments is receiving intense public and scientific attention. Yet a suitable sample preparation method that would enable extraction and enrichment of a wide range of such compounds from water is missing. The focus of this paper was to develop an enhanced solid phase extraction (SPE) protocol which enabled isolation of parent compounds and low molecular weight transformation products (that are produced after treatment of water with ozone) from different water matrices. Ten SPE sorbents were evaluated with regard to their ability to extract acidic, neutral, and basic compounds from water at several pH values. Highest recoveries (91-99 %) for all analytes in pure water were obtained by combining strong anion and cation exchangers of two manufacturers in a tandem mode without pH adjustment. Tandem Oasis (MAX+MCX) was finally applied to extract the spiked analytes from tap water, surface water, and several wastewater samples. The efficiency of the used SPE procedure was examined using an optimized liquid chromatography-electrospray ionization-tandem mass spectrometry (LC-ESI-MS/MS) method using multiple reaction monitoring (MRM) mode. The occurrence of some of the investigated TPs in environmental water matrices was proven for the first time in this study. Method quantification limits (MQLs) for all compounds ranged from 3.7 to 15.3 ng/L in all matrices. Recoveries (%RE) were between 90 and 110 %. Intraday and interday precision, expressed as relative standard deviation, varied from 0.7 to 5.9 % and 1.8 to 10.3 %, respectively. Matrix effect (%ME) evaluation demonstrated that even complex sample matrices did not show significant ion suppression or enhancement. The applicability of the method was shown during two sampling campaigns at Ruhr river and a wastewater treatment plant (WWTP) equipped with an ozonation step after regular

  14. Fabrication, characterization and photocatalytic properties of Ag/AgI/BiOI heteronanostructures supported on rectorite via a cation-exchange method

    SciTech Connect

    Chen, Yunfang; Fang, Jianzhang; Lu, Shaoyou; Wu, Yan; Chen, Dazhi; Huang, Liyan; Xu, Weicheng; Zhu, Ximiao; Fang, Zhanqiang

    2015-04-15

    Highlights: • Ag/AgI/BiOI-rectorite was prepared by twice cation-exchange process. • Ag/AgI/BiOI-rectorite photocatalyst possessed SPR and adsorption capacity. • Ag/AgI/BiOI-rectorite exhibited highly photocatalytic activity. • Trapped holes and ·O{sub 2}{sup −} were formed active species in the photocatalytic system. - Abstract: In this work, a new plasmonic photocatalyst Ag/AgI/BiOI-rectorite was prepared via a cation exchange process. The photocatalyst had been characterized by X-ray powder diffraction (XRD), Raman spectra, nitrogen sorption (BET), field-emission scanning electron microscope (FE-SEM), X-ray photoelectron spectroscopy (XPS) and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity, which was evaluated by degradation of rhodamine B (RhB) and bisphenol A (BPA) under visible light irradiation, was enhanced significantly by loading Ag/AgI/BiOI nanoparticles onto rectorite. The photogenerated holes and superoxide radical (·O{sub 2}{sup −}) were both formed as active species for the photocatalytic reactions under visible light irradiation. The existence of metallic Ag particles, which possess the surface plasmon resonance effect, acted as an indispensable role in the photocatalytic reaction.

  15. Quantification of Site-Specific Cation Exchange in Metal-Organic Frameworks Using Multi-Wavelength Anomalous X-ray Dispersion

    SciTech Connect

    Brozek, Carl K.; Cozzolino, Anthony F.; Teat, Simon J.; Chen, Yu-Sheng; Dinc,; #259; Mircea,

    2013-09-23

    We employed multiwavelength anomalous X-ray dispersion to determine the relative cation occupation at two crystallographically distinct metal sites in Fe2+-, Cu2+-, and Zn2+-exchanged versions of the microporous metal–organic framework (MOF) known as MnMnBTT (BTT = 1,3,5-benzenetristetrazolate). By exploiting the dispersive differences between Mn, Fe, Cu, and Zn, the extent and location of cation exchange were determined from single crystal X-ray diffraction data sets collected near the K edges of Mn2+ and of the substituting metal, and at a wavelength remote from either edge as a reference. Comparing the anomalous dispersion between these measurements indicated that the extent of Mn2+ replacement depends on the identity of the substituting metal. We contrasted two unique methods to analyze this data with a conventional approach and evaluated their limitations with emphasis on the general application of this method to other heterometallic MOFs, where site-specific metal identification is fundamental to tuning catalytic and physical properties.

  16. Cation Exchange Combined with Kirkendall Effect in the Preparation of SnTe/CdTe and CdTe/SnTe Core/Shell Nanocrystals.

    PubMed

    Jang, Youngjin; Yanover, Diana; Čapek, Richard Karel; Shapiro, Arthur; Grumbach, Nathan; Kauffmann, Yaron; Sashchiuk, Aldona; Lifshitz, Efrat

    2016-07-01

    Controlling the synthesis of narrow band gap semiconductor nanocrystals (NCs) with a high-quality surface is of prime importance for scientific and technological interests. This Letter presents facile solution-phase syntheses of SnTe NCs and their corresponding core/shell heterostructures. Here, we synthesized monodisperse and highly crystalline SnTe NCs by employing an inexpensive, nontoxic precursor, SnCl2, the reactivity of which was enhanced by adding a reducing agent, 1,2-hexadecanediol. Moreover, we developed a synthesis procedure for the formation of SnTe-based core/shell NCs by combining the cation exchange and the Kirkendall effect. The cation exchange of Sn(2+) by Cd(2+) at the surface allowed primarily the formation of SnTe/CdTe core/shell NCs. Further continuation of the reaction promoted an intensive diffusion of the Cd(2+) ions, which via the Kirkendall effect led to the formation of the inverted CdTe/SnTe core/shell NCs. PMID:27331900

  17. Many-body exchange-repulsion in polarizable molecular mechanics. I. Orbital-based approximations and applications to hydrated metal cation complexes.

    PubMed

    Chaudret, Robin; Gresh, Nohad; Parisel, Olivier; Piquemal, Jean-Philip

    2011-11-15

    We have quantified the extent of the nonadditivity of the short-range exchange-repulsion energy, E(exch-rep), in several polycoordinated complexes of alkali, alkaline-earth, transition, and metal cations. This was done by performing ab initio energy decomposition analyses of interaction energies in these complexes. The magnitude of E(exch-rep(n-body, n > 2)) was found to be strongly cation-dependent, ranging from close to zero for some alkali metal complexes to about 6 kcal/mol for the hexahydrated Zn(2+) complex. In all cases, the cation-water molecules, E(exch-rep(three-body)), has been found to be the dominant contribution to many-body exchange-repulsion effects, higher order terms being negligible. As the physical basis of this effect is discussed, a three-center exponential term was introduced in the SIBFA (Sum of Interactions Between Fragments Ab initio computed) polarizable molecular mechanics procedure to model such effects. The three-body correction is added to the two-center (two-body) overlap-like formulation of the short-range repulsion contribution, E(rep), which is grounded on simplified integrals obtained from localized molecular orbital theory. The present term is computed on using mostly precomputed two-body terms and, therefore, does not increase significantly the computational cost of the method. It was shown to match closely E(three-body) in a series of test cases bearing on the complexes of Ca(2+), Zn(2+), and Hg(2+). For example, its introduction enabled to restore the correct tetrahedral versus square planar preference found from quantum chemistry calculations on the tetrahydrate of Hg(2+) and [Hg(H(2)O)(4)](2+). PMID:21793002

  18. Volatile organic acid adsorption and cation dissociation by porphyritic andesite for enhancing hydrolysis and acidogenesis of solid food wastes.

    PubMed

    Cheng, Fan; Li, Ming; Li, Dawei; Chen, Ling; Jiang, Weizhong; Kitamura, Yutaka; Li, Baoming

    2010-07-01

    Volatile organic acid adsorption, cation dissociation by porphyritic andesite, and their effects on the hydrolysis and acidogenesis of solid food wastes were evaluated through batch experiments. The acetic acid adsorption experiments show that pH was mainly regulated by H(+) adsorption. The mono-layer and multi-layer adsorption were found under the low (8.3-83.2 mmol/L) and high (133.22-532.89 mmol/L) initial acetic acid concentration, respectively. The dissociated cations concentration in acidic solution showed the predominance of Ca(2+). Porphyritic andesite addition elevated the pH levels and accelerated hydrolysis and acidogenesis in the batch fermentation experiment. Leachate of porphyritic andesite addition achieved the highest hydrolysis constant of 22.1 x 10(-3)kgm(-2)d(-1) and VS degradation rates of 3.9 g L(-1)d(-1). The highest activity of microorganisms represented by specific growth rate of ATP, 0.16d(-1), and specific consumption rate of Ca(2+), 0.18d(-1), was obtained by adding leachate of porphyritic andesite.

  19. Volatile organic acid adsorption and cation dissociation by porphyritic andesite for enhancing hydrolysis and acidogenesis of solid food wastes.

    PubMed

    Cheng, Fan; Li, Ming; Li, Dawei; Chen, Ling; Jiang, Weizhong; Kitamura, Yutaka; Li, Baoming

    2010-07-01

    Volatile organic acid adsorption, cation dissociation by porphyritic andesite, and their effects on the hydrolysis and acidogenesis of solid food wastes were evaluated through batch experiments. The acetic acid adsorption experiments show that pH was mainly regulated by H(+) adsorption. The mono-layer and multi-layer adsorption were found under the low (8.3-83.2 mmol/L) and high (133.22-532.89 mmol/L) initial acetic acid concentration, respectively. The dissociated cations concentration in acidic solution showed the predominance of Ca(2+). Porphyritic andesite addition elevated the pH levels and accelerated hydrolysis and acidogenesis in the batch fermentation experiment. Leachate of porphyritic andesite addition achieved the highest hydrolysis constant of 22.1 x 10(-3)kgm(-2)d(-1) and VS degradation rates of 3.9 g L(-1)d(-1). The highest activity of microorganisms represented by specific growth rate of ATP, 0.16d(-1), and specific consumption rate of Ca(2+), 0.18d(-1), was obtained by adding leachate of porphyritic andesite. PMID:20156676

  20. Derivatives of the cationic plant alkaloids berberine and palmatine amplify protonophorous activity of fatty acids in model membranes and mitochondria.

    PubMed

    Pustovidko, Antonina V; Rokitskaya, Tatiana I; Severina, Inna I; Simonyan, Ruben A; Trendeleva, Tatiana A; Lyamzaev, Konstantin G; Antonenko, Yuri N; Rogov, Anton G; Zvyagilskaya, Renata A; Skulachev, Vladimir P; Chernyak, Boris V

    2013-09-01

    Previously it has been shown by our group that berberine and palmatine, penetrating cations of plant origin, when conjugated with plastoquinone (SkQBerb and SkQPalm), can accumulate in isolated mitochondria or in mitochondria of living cells and effectively protect them from oxidative damage. In the present work, we demonstrate that SkQBerb, SkQPalm, and their analogs lacking the plastoquinone moiety (C10Berb and C10Palm) operate as mitochondria-targeted compounds facilitating protonophorous effect of free fatty acids. These compounds induce proton transport mediated by small concentrations of added fatty acids both in planar and liposomal model lipid membranes. In mitochondria, such an effect can be carried out by endogenous fatty acids and the adenine nucleotide translocase.

  1. Regional trends in soil acidification and exchangeable metal concentrations in relation to acid deposition rates.

    PubMed

    Stevens, Carly J; Dise, Nancy B; Gowing, David J

    2009-01-01

    The deposition of high levels of reactive nitrogen (N) and sulphur (S), or the legacy of that deposition, remain among the world's most important environmental problems. Although regional impacts of acid deposition in aquatic ecosystems have been well documented, quantitative evidence of wide-scale impacts on terrestrial ecosystems is not common. In this study we analysed surface and subsoil chemistry of 68 acid grassland sites across the UK along a gradient of acid deposition, and statistically related the concentrations of exchangeable soil metals (1 M KCl extraction) to a range of potential drivers. The deposition of N, S or acid deposition was the primary correlate for 8 of 13 exchangeable metals measured in the topsoil and 5 of 14 exchangeable metals in the subsoil. In particular, exchangeable aluminium and lead both show increased levels above a soil pH threshold of about 4.5, strongly related to the deposition flux of acid compounds.

  2. Nearly 1000 Protein Identifications from 50 ng of Xenopus laevis Zygote Homogenate Using Online Sample Preparation on a Strong Cation Exchange Monolith Based Microreactor Coupled with Capillary Zone Electrophoresis.

    PubMed

    Zhang, Zhenbin; Sun, Liangliang; Zhu, Guijie; Cox, Olivia F; Huber, Paul W; Dovichi, Norman J

    2016-01-01

    A sulfonate-silica hybrid strong cation exchange monolith microreactor was synthesized and coupled to a linear polyacrylamide coated capillary for online sample preparation and capillary zone electrophoresis-tandem mass spectrometry (CZE-MS/MS) bottom-up proteomic analysis. The protein sample was loaded onto the microreactor in an acidic buffer. After online reduction, alkylation, and digestion with trypsin, the digests were eluted with 200 mM ammonium bicarbonate at pH 8.2 for CZE-MS/MS analysis using 1 M acetic acid as the background electrolyte. This combination of basic elution and acidic background electrolytes results in both sample stacking and formation of a dynamic pH junction. 369 protein groups and 1274 peptides were identified from 50 ng of Xenopus laevis zygote homogenate, which is comparable with an offline sample preparation method, but the time required for sample preparation was decreased from over 24 h to less than 40 min. Dramatically improved performance was produced by coupling the reactor to a longer separation capillary (∼100 cm) and a Q Exactive HF mass spectrometer. 975 protein groups and 3749 peptides were identified from 50 ng of Xenopus protein using the online sample preparation method.

  3. Acid-promoted chemoselective introduction of amide functionality onto aromatic compounds mediated by an isocyanate cation generated from carbamate.

    PubMed

    Sumita, Akinari; Kurouchi, Hiroaki; Otani, Yuko; Ohwada, Tomohiko

    2014-10-01

    Carbamates have been used as precursors of isocyanates, but heating in the presence of strong acids is required because cleavage of the C-O bond in carbamates is energy-demanding even in acid media. Direct amidation of aromatic compounds by isocyanate cations generated at room temperature from carbamoyl salicylates in trifluoromethanesulfonic acid (TfOH) was examined. Carbamates with ortho-salicylate as an ether group (carbamoyl salicylates) showed dramatically accelerated O-C bond dissociation in TfOH, which resulted in facile generation of the isocyanate cation. These chemoselective intermolecular aromatic amidation reactions proceeded even at room temperature and showed good compatibility with other electrophilic functionalities and high discrimination between N-monosubstituted carbamate and N,N-disubstituted carbamate. The reaction rates of secondary and tertiary amide formation were markedly different, and this difference was utilized to achieve successive (tandem) amidation reactions of molecules with an N-monosubstituted carbamate and an N,N-disubstituted carbamate with two kinds of aromatic compounds.

  4. Kinetic approach to evaluate the energy and entropy of activation for the exchange of alkaline earth metal ions on tin(IV) tungstate cation exchanger

    SciTech Connect

    Varshney, K.G.; Khan, A.A.; Varshney, K.; Agrawal, S.

    1984-01-01

    A new approach based on the Nernst-Planck equations has been applied to study the reaction kinetics on the surface of tin(IV) tungstate for the Mg(II)-H(I), Ca(II)-H(I), Sr(II)-H(I) and Ba(II)-H(I) exchanges under the conditions favouring a particle diffusion phenomenon. On the basis of these studies the various physical parameters such as the effective diffusion coefficients, activation energies and entropies of activation have been evaluated which give some informations regarding the mechanism of ion-exchange on the surface of inorganic materials. 25 references, 3 figures, 3 tables.

  5. One-step Conjugation of Glycyrrhetinic Acid to Cationic Polymers for High-performance Gene Delivery to Cultured Liver Cell

    PubMed Central

    Cong, Yue; Shi, Bingyang; Lu, Yiqing; Wen, Shihui; Chung, Roger; Jin, Dayong

    2016-01-01

    Gene therapies represent a promising therapeutic route for liver cancers, but major challenges remain in the design of safe and efficient gene-targeting delivery systems. For example, cationic polymers show good transfection efficiency as gene carriers, but are hindered by cytotoxicity and non-specific targeting. Here we report a versatile method of one-step conjugation of glycyrrhetinic acid (GA) to reduce cytotoxicity and improve the cultured liver cell -targeting capability of cationic polymers. We have explored a series of cationic polymer derivatives by coupling different ratios of GA to polypropylenimine (PPI) dendrimer. These new gene carriers (GA-PPI dendrimer) were systematically characterized by UV-vis,1H NMR titration, electron microscopy, zeta potential, dynamic light-scattering, gel electrophoresis, confocal microscopy and flow cytometry. We demonstrate that GA-PPI dendrimers can efficiently load and protect pDNA, via formation of nanostructured GA-PPI/pDNA polyplexes. With optimal GA substitution degree (6.31%), GA-PPI dendrimers deliver higher liver cell transfection efficiency (43.5% vs 22.3%) and lower cytotoxicity (94.3% vs 62.5%, cell viability) than the commercial bench-mark DNA carrier bPEI (25kDa) with cultured liver model cells (HepG2). There results suggest that our new GA-PPI dendrimer are a promising candidate gene carrier for targeted liver cancer therapy. PMID:26902258

  6. Applying reactive models to column experiments to assess the hydrogeochemistry of seawater intrusion: Optimising ACUAINTRUSION and selecting cation exchange coefficients with PHREEQC

    NASA Astrophysics Data System (ADS)

    Boluda-Botella, N.; Valdes-Abellan, J.; Pedraza, R.

    2014-03-01

    Three sets of laboratory column experimental results concerning the hydrogeochemistry of seawater intrusion have been modelled using two codes: ACUAINTRUSION (Chemical Engineering Department, University of Alicante) and PHREEQC (U.S.G.S.). These reactive models utilise the hydrodynamic parameters determined using the ACUAINTRUSION TRANSPORT software and fit the chloride breakthrough curves perfectly. The ACUAINTRUSION code was improved, and the instabilities were studied relative to the discretisation. The relative square errors were obtained using different combinations of the spatial and temporal steps: the global error for the total experimental data and the partial error for each element. Good simulations for the three experiments were obtained using the ACUAINTRUSION software with slight variations in the selectivity coefficients for both sediments determined in batch experiments with fresh water. The cation exchange parameters included in ACUAINTRUSION are those reported by the Gapon convention with modified exponents for the Ca/Mg exchange. PHREEQC simulations performed using the Gains-Thomas convention were unsatisfactory, with the exchange coefficients from the database of PHREEQC (or range), but those determined with fresh water - natural sediment allowed only an approximation to be obtained. For the treated sediment, the adjusted exchange coefficients were determined to improve the simulation and are vastly different from those from the database of PHREEQC or batch experiment values; however, these values fall in an order similar to the others determined under dynamic conditions. Different cation concentrations were simulated using two different software packages; this disparity could be attributed to the defined selectivity coefficients that affect the gypsum equilibrium. Consequently, different calculated sulphate concentrations are obtained using each type of software; a smaller mismatch was predicted using ACUAINTRUSION. In general, the presented

  7. Ae4 (Slc4a9) is an electroneutral monovalent cation-dependent Cl−/HCO3− exchanger

    PubMed Central

    Peña-Münzenmayer, Gaspar; George, Alvin T.; Shull, Gary E.; Melvin, James E.

    2016-01-01

    Ae4 (Slc4a9) belongs to the Slc4a family of Cl−/HCO3− exchangers and Na+-HCO3− cotransporters, but its ion transport cycle is poorly understood. In this study, we find that native Ae4 activity in mouse salivary gland acinar cells supports Na+-dependent Cl−/HCO3− exchange that is comparable with that obtained upon heterologous expression of mouse Ae4 and human AE4 in CHO-K1 cells. Additionally, whole cell recordings and ion concentration measurements demonstrate that Na+ is transported by Ae4 in the same direction as HCO3− (and opposite to that of Cl−) and that ion transport is not associated with changes in membrane potential. We also find that Ae4 can mediate Na+-HCO3− cotransport–like activity under Cl−-free conditions. However, whole cell recordings show that this apparent Na+-HCO3− cotransport activity is in fact electroneutral HCO3−/Na+-HCO3− exchange. Although the Ae4 anion exchanger is thought to regulate intracellular Cl− concentration in exocrine gland acinar cells, our thermodynamic calculations predict that the intracellular Na+, Cl−, and HCO3− concentrations required for Ae4-mediated Cl− influx differ markedly from those reported for acinar secretory cells at rest or under sustained stimulation. Given that K+ ions share many properties with Na+ ions and reach intracellular concentrations of 140–150 mM (essentially the same as extracellular [Na+]), we hypothesize that Ae4 could mediate K+-dependent Cl−/HCO3− exchange. Indeed, we find that Ae4 mediates Cl−/HCO3− exchange activity in the presence of K+ as well as Cs+, Li+, and Rb+. In summary, our results strongly suggest that Ae4 is an electroneutral Cl−/nonselective cation–HCO3− exchanger. We postulate that the physiological role of Ae4 in secretory cells is to promote Cl− influx in exchange for K+(Na+) and HCO3− ions. PMID:27114614

  8. Computing in mammalian cells with nucleic acid strand exchange

    NASA Astrophysics Data System (ADS)

    Groves, Benjamin; Chen, Yuan-Jyue; Zurla, Chiara; Pochekailov, Sergii; Kirschman, Jonathan L.; Santangelo, Philip J.; Seelig, Georg

    2016-03-01

    DNA strand displacement has been widely used for the design of molecular circuits, motors, and sensors in cell-free settings. Recently, it has been shown that this technology can also operate in biological environments, but capabilities remain limited. Here, we look to adapt strand displacement and exchange reactions to mammalian cells and report DNA circuitry that can directly interact with a native mRNA. We began by optimizing the cellular performance of fluorescent reporters based on four-way strand exchange reactions and identified robust design principles by systematically varying the molecular structure, chemistry and delivery method. Next, we developed and tested AND and OR logic gates based on four-way strand exchange, demonstrating the feasibility of multi-input logic. Finally, we established that functional siRNA could be activated through strand exchange, and used native mRNA as programmable scaffolds for co-localizing gates and visualizing their operation with subcellular resolution.

  9. Computing in mammalian cells with nucleic acid strand exchange

    PubMed Central

    Pochekailov, Sergii; Kirschman, Jonathan L.; Santangelo, Philip J.; Seelig, Georg

    2015-01-01

    DNA strand displacement has been widely used for the design of molecular circuits, motors, and sensors in cell-free settings. Recently, it has been shown that this technology can also operate in biological environments, but capabilities remain limited. Here, we look to adapt strand displacement and exchange reactions to mammalian cells and report DNA circuitry that can directly interact with a native mRNA. We began by optimizing the cellular performance of fluorescent reporters based on four-way strand exchange reactions and identified robust design principles by systematically varying the molecular structure, chemistry and delivery method. Next, we developed and tested AND and OR logic gates based on four-way strand exchange, demonstrating the feasibility of multi-input logic. Finally, we established that functional siRNA could be activated through strand exchange, and used native mRNA as programmable scaffolds for co-localizing gates and visualizing their operation with subcellular resolution. PMID:26689378

  10. Extraction of steroidal glucosiduronic acids from aqueous solutions by anionic liquid ion-exchangers

    PubMed Central

    Mattox, Vernon R.; Litwiller, Robert D.; Goodrich, June E.

    1972-01-01

    A pilot study on the extraction of three steroidal glucosiduronic acids from water into organic solutions of liquid ion-exchangers is reported. A single extraction of a 0.5mm aqueous solution of either 11-deoxycorticosterone 21-glucosiduronic acid or cortisone 21-glucosiduronic acid with 0.1m-tetraheptylammonium chloride in chloroform took more than 99% of the conjugate into the organic phase; under the same conditions, the very polar conjugate, β-cortol 3-glucosiduronic acid, was extracted to the extent of 43%. The presence of a small amount of chloride, acetate, or sulphate ion in the aqueous phase inhibited extraction, but making the aqueous phase 4.0m with ammonium sulphate promoted extraction strongly. An increase in the concentration of ion-exchanger in the organic phase also promoted extraction. The amount of cortisone 21-glucosiduronic acid extracted by tetraheptylammonium chloride over the pH range of 3.9 to 10.7 was essentially constant. Chloroform solutions of a tertiary, a secondary, or a primary amine hydrochloride also will extract cortisone 21-glucosiduronic acid from water. The various liquid ion exchangers will extract steroidal glucosiduronic acid methyl esters from water into chloroform, although less completely than the corresponding free acids. The extraction of the glucosiduronic acids from water by tetraheptylammonium chloride occurs by an ion-exchange process; extraction of the esters does not involve ion exchange. PMID:5075264

  11. The Effects of Trivalent Lanthanide Cationization on the Electron Transfer Dissociation of Acidic Fibrinopeptide B and its Analogs.

    PubMed

    Commodore, Juliette J; Cassady, Carolyn J

    2016-09-01

    Electrospray ionization (ESI) on mixtures of acidic fibrinopeptide B and two peptide analogs with trivalent lanthanide salts generates [M + Met + H](4+), [M + Met](3+), and [M + Met -H](2+), where M = peptide and Met = metal (except radioactive promethium). These ions undergo extensive and highly efficient electron transfer dissociation (ETD) to form metallated and non-metallated c- and z-ions. All metal adducted product ions contain at least two acidic sites, which suggest attachment of the lanthanide cation at the side chains of one or more acidic residues. The three peptides undergo similar fragmentation. ETD on [M + Met + H](4+) leads to cleavage at every residue; the presence of both a metal ion and an extra proton is very effective in promoting sequence-informative fragmentation. Backbone dissociation of [M + Met](3+) is also extensive, although cleavage does not always occur between adjacent glutamic acid residues. For [M + Met - H ](2+), a more limited range of product ions form. All lanthanide metal peptide complexes display similar fragmentation except for europium (Eu). ETD on [M + Eu - H](2+) and [M + Eu](3+) yields a limited amount of peptide backbone cleavage; however, [M + Eu + H](4+) dissociates extensively with cleavage at every residue. With the exception of the results for Eu(III), metallated peptide ion formation by ESI, ETD fragmentation efficiencies, and product ion formation are unaffected by the identity of the lanthanide cation. Adduction with trivalent lanthanide metal ions is a promising tool for sequence analysis of acidic peptides by ETD. Graphical Abstract ᅟ. PMID:27294379

  12. Asparagine promotes cancer cell proliferation through use as an amino acid exchange factor.

    PubMed

    Krall, Abigail S; Xu, Shili; Graeber, Thomas G; Braas, Daniel; Christofk, Heather R

    2016-01-01

    Cellular amino acid uptake is critical for mTOR complex 1 (mTORC1) activation and cell proliferation. However, the regulation of amino acid uptake is not well-understood. Here we describe a role for asparagine as an amino acid exchange factor: intracellular asparagine exchanges with extracellular amino acids. Through asparagine synthetase knockdown and altering of media asparagine concentrations, we show that intracellular asparagine levels regulate uptake of amino acids, especially serine, arginine and histidine. Through its exchange factor role, asparagine regulates mTORC1 activity and protein synthesis. In addition, we show that asparagine regulation of serine uptake influences serine metabolism and nucleotide synthesis, suggesting that asparagine is involved in coordinating protein and nucleotide synthesis. Finally, we show that maintenance of intracellular asparagine levels is critical for cancer cell growth. Collectively, our results indicate that asparagine is an important regulator of cancer cell amino acid homeostasis, anabolic metabolism and proliferation. PMID:27126896

  13. A method to buffer the concentrations of free Zn and Cd ions using a cation exchange resin in bacterial toxicity studies

    SciTech Connect

    Knight, B.; McGrath, S.P.

    1995-12-01

    The chemical form or species of metal present in a growth system is crucial to the toxicity of that metal. A growth medium is described in which the free metal concentration of either Zn or Cd is known. A method using a cation exchange resin as a buffer to maintain free metal ion concentrations during microbial growth is discussed. Using a buffered system, free concentrations of 3.4 {micro}g Cd L{sup {minus}1} and 57 {micro}g Zn L{sup {minus}1} reduced the growth rate of a sensitive isolate of Rhizobium leguminosarum biovar trifolii. The results demonstrate that to assess the true toxicity of Cd and Zn, the free ion concentration must be considered and that small free concentrations must be buffered.

  14. Role of competitive cation exchange on chromatographic displacement of cesium in the vadose zone beneath the Hanford S/SX tank farm

    SciTech Connect

    Lichtner, Peter C.; Yabusaki, Steve; Pruess, Karsten; Steefel, Carl I.

    2003-10-01

    Migration of radionuclides under the SX-tank farm at the Hanford nuclear waste complex involves interaction of variably water saturated sediments with concentrated NaOH-NaNO3-NaNO2 solutions that have leaked from the tanks. Constant Kd models for describing radionuclide retardation are not valid under these conditions because of strong competition for sorption sites by abundant Na+ ions, and because of dramatically changing solution compositions with time as the highly concentrated tank fluid becomes diluted as it mixes with infiltrating rainwater. A mechanistic multicomponent sorption model is required that can account for effects of competition and spatially and temporally variable solution compositions. To investigate the influence of the high ionic strength tank fluids on Cs+ migration, numerical calculations are performed using the multiphase-multicomponent reactive transport code FLOTRAN. The computer model describes reactive transport in nonisothermal, variably saturated porous media including both liquid and gas phases. Pitzer activity coefficient corrections are used to describe the high ionic strength solutions. The calculations take into account multicomponent cation exchange based on measured selectivity coefficients specific to the Hanford sediments. Solution composition data obtained from Well 299-W23-19, documenting a moderately concentrated leak from the SX-115 tank, are used to calibrate the model. In addition to exchange of cations Na+, K+, Ca2+, and Cs+, aqueous complexing and a kinetic description of precipitation and dissolution of calcite are also included in the calculations. The fitted infiltration rate of 0.08 m yr-1, and fitted cation exchange capacity of 0.05 mol kg-1 are consistent with measured values for the Hanford sediments. A sensitivity analysis is performed for Na+ concentrations ranging from 5 to 20 m to investigate the mobility of Cs+ interacting with a highly concentrated background electrolyte solution believed to have been

  15. Role of Competitive Cation Exchange on Chromatographic Displacement of Cesium in the Vadose Zone beneath the Hanford S/SX Tank Farm

    SciTech Connect

    Lichtner, Peter C.; Yabusaki, Steven B.; Pruess, Karsten; Steefel, Carl

    2004-01-12

    Migration of radionuclides under the SX-tank farm at the Hanford nuclear waste complex involves interaction of variably water saturated sediments with concentrated NaOH-NaNO{sub 3}-NaNO{sub 2} solutions that have leaked from the tanks. Constant K{sub d} models for describing radionuclide retardation are not valid under these conditions because of strong competition for sorption sites by abundant Na{sup +} ions, and because of dramatically changing solution compositions with time as the highly concentrated tank fluid becomes diluted as it mixes with infiltrating rainwater. A mechanistic multicomponent sorption model is required that can account for effects of competition and spatially and temporally variable solution compositions. To investigate the influence of the high ionic strength tank fluids on Cs{sup +} migration, numerical calculations are performed using the multiphase-multicomponent reactive transport code FLOTRAN. The computer model describes reactive transport in nonisothermal, variably saturated porous media including both liquid and gas phases. Pitzer activity coefficient corrections are used to describe the high ionic strength solutions. The calculations take into account multicomponent cation exchange based on measured selectivity coefficients specific to the Hanford sediments. Solution composition data obtained from Well 299-W23-19, documenting a moderately concentrated leak from the SX-115 tank, are used to calibrate the model. In addition to exchange of cations Na{sup +}, K{sup +}, Ca{sup 2+}, and Cs{sup +}, aqueous complexing and a kinetic description of precipitation and dissolution of calcite are also included in the calculations. The fitted infiltration rate of 0.08 m yr{sup -1}, and fitted cation exchange capacity of 0.05 mol kg{sup -1} are consistent with measured values for the Hanford sediments. A sensitivity analysis is performed for Na{sup +} concentrations ranging from 5 to 20 m to investigate the mobility of Cs{sup +} interacting with

  16. Investigation of the swelling behavior of cationic exchange resins saturated with Na{sup +} ions in a C{sub 3}S paste

    SciTech Connect

    Lafond, E.; Cau Dit Coumes, C.; Gauffinet, S.; Chartier, D.; Le Bescop, P.; Stefan, L.; Nonat, A.

    2015-03-15

    Ion exchange resins (IERs) are widely used by the nuclear industry to decontaminate radioactive effluents. Spent products are usually encapsulated in cementitious materials. However, the solidified waste form can exhibit strong expansion, possibly leading to cracking, if the appropriate binder is not used. In this work, the interactions between cationic resins in the Na{sup +} form and tricalcium silicate are investigated during the early stages of hydration in order to gain a better understanding of the expansion process. It is shown that the IERs exhibit a transient swelling of small magnitude due to the decrease in the osmotic pressure of the external solution. This expansion, which occurs just after setting, is sufficient to damage the material which is poorly consolidated for several reasons: low degree of hydration, precipitation of poorly cohesive sodium-bearing C–S–H, and very heterogeneous microstructure with zones of high porosity.

  17. Sequential Determination of Total Arsenic and Cadmium in Concentrated Cadmium Sulphate Solutions by Flow-Through Stripping Chronopotentiometry after Online Cation Exchanger Separation

    PubMed Central

    Cacho, Frantisek; Lauko, Lukas; Manova, Alena; Dzurov, Jan; Beinrohr, Ernest

    2012-01-01

    Flow-through stripping chronopotentiometry with a gold wire electrode was used for the determination of total arsenic and cadmium in cadmium sulphate solutions for cadmium production. The analysis is based on the online separation of arsenic as arsenate anion from cadmium cations by means of a cation exchanger. On measuring arsenate in the effluent, the trapped cadmium is eluted by sodium chloride solution and determined in a small segment of the effluent by making use of the same electrode. The elaborated protocol enables a full automatic measurement of both species in the same sample solution. The accuracy of the results was confirmed by atomic absorption spectrometry. The LOD and LOQ for Arsenic were found to be 0.9 μg dm−3 and 2.7 μg dm−3, respectively. A linear response range was observed in the concentration range of 1 to 300 μg dm−3 for sample volumes of 4 mL. The repeatability and reproducibility were found to be 2.9% and 5.2%, respectively. The linear response range for cadmium was found to be 0.5 to 60 g/L. The method was tested on samples from a cadmium production plant. PMID:22448343

  18. Synthesis of Capsule-like Porous Hollow Nanonickel Cobalt Sulfides via Cation Exchange Based on the Kirkendall Effect for High-Performance Supercapacitors.

    PubMed

    Tang, Yongfu; Chen, Shunji; Mu, Shichun; Chen, Teng; Qiao, Yuqing; Yu, Shengxue; Gao, Faming

    2016-04-20

    To construct a suitable three-dimensional structure for ionic transport on the surface of the active materials for a supercapacitor, porous hollow nickel cobalt sulfides are successfully synthesized via a facile and efficient cation-exchange reaction in a hydrothermal process involving the Kirkendall effect with γ-MnS nanorods as a sacrificial template. The formation mechanism of the hollow nickel cobalt sulfides is carefully illustrated via the tuning reaction time and reaction temperature during the cation-exchange process. Due to the ingenious porous hollow structure that offers a high surface area for electrochemical reaction and suitable paths for ionic transport, porous hollow nickel cobalt sulfide electrodes exhibit high electrochemical performance. The Ni(1.77)Co(1.23)S4 electrode delivers a high specific capacity of 224.5 mAh g(-1) at a current density of 0.25 A g(-1) and a high capacity retention of 87.0% at 10 A g(-1). An all-solid-state asymmetric supercapacitor, assembled with a Ni(1.77)Co(1.23)S4 electrode as the positive electrode and a homemade activated carbon electrode as the negative electrode (denoted as NCS//HMC), exhibits a high energy density of 42.7 Wh kg(-1) at a power density of 190.8 W kg(-1) and even 29.4 Wh kg(-1) at 3.6 kW kg(-1). The fully charged as-prepared asymmetric supercapacitor can light up a light emitting diode (LED) indicator for more than 1 h, indicating promising practical applications of the hollow nickel cobalt sulfides and the NCS//HMC asymmetric supercapacitor.

  19. LA-ICP-MS of rare earth elements concentrated in cation-exchange resin particles for origin attribution of uranium ore concentrate.

    PubMed

    Asai, Shiho; Limbeck, Andreas

    2015-04-01

    Rare earth elements (REE) concentrated on cation-exchange resin particles were measured with laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) to obtain chondrite-normalized REE plots. The sensitivity of REE increased in ascending order of the atomic number, according to the sensitivity trend in pneumatic nebulization ICP-MS (PN-ICP-MS). The signal intensities of REE were nearly proportional to the concentrations of REE in the immersion solution used for particle-preparation. Minimum measurable concentration calculated from the net signals of REE was approximately 1 ng/g corresponding to 0.1 ng in the particle-preparation solution. In LA analysis, formation of oxide and hydroxide of the light REE and Ba which causes spectral interferences in the heavy REE measurement was effectively attenuated due to the solvent-free measurement capability, compared to conventional PN-ICP-MS. To evaluate the applicability of the proposed method, the REE-adsorbed particles prepared by immersing them in a U-bearing solution (commercially available U standard solution) were measured with LA-ICP-MS. Aside from the LA analysis, each concentration of REE in the same U standard solution was determined with conventional PN-ICP-MS after separating REE by cation-exchange chromatography. The concentrations of REE were ranging from 0.04 (Pr) to 1.08 (Dy) μg/g-U. The chondrite-normalized plot obtained through LA-ICP-MS analysis of the U standard sample exhibited close agreement with that obtained through the PN-ICP-MS of the REE-separated solution within the uncertainties.

  20. Synthesis of Capsule-like Porous Hollow Nanonickel Cobalt Sulfides via Cation Exchange Based on the Kirkendall Effect for High-Performance Supercapacitors.

    PubMed

    Tang, Yongfu; Chen, Shunji; Mu, Shichun; Chen, Teng; Qiao, Yuqing; Yu, Shengxue; Gao, Faming

    2016-04-20

    To construct a suitable three-dimensional structure for ionic transport on the surface of the active materials for a supercapacitor, porous hollow nickel cobalt sulfides are successfully synthesized via a facile and efficient cation-exchange reaction in a hydrothermal process involving the Kirkendall effect with γ-MnS nanorods as a sacrificial template. The formation mechanism of the hollow nickel cobalt sulfides is carefully illustrated via the tuning reaction time and reaction temperature during the cation-exchange process. Due to the ingenious porous hollow structure that offers a high surface area for electrochemical reaction and suitable paths for ionic transport, porous hollow nickel cobalt sulfide electrodes exhibit high electrochemical performance. The Ni(1.77)Co(1.23)S4 electrode delivers a high specific capacity of 224.5 mAh g(-1) at a current density of 0.25 A g(-1) and a high capacity retention of 87.0% at 10 A g(-1). An all-solid-state asymmetric supercapacitor, assembled with a Ni(1.77)Co(1.23)S4 electrode as the positive electrode and a homemade activated carbon electrode as the negative electrode (denoted as NCS//HMC), exhibits a high energy density of 42.7 Wh kg(-1) at a power density of 190.8 W kg(-1) and even 29.4 Wh kg(-1) at 3.6 kW kg(-1). The fully charged as-prepared asymmetric supercapacitor can light up a light emitting diode (LED) indicator for more than 1 h, indicating promising practical applications of the hollow nickel cobalt sulfides and the NCS//HMC asymmetric supercapacitor. PMID:27031254