Science.gov

Sample records for acidified pig slurry

  1. Toxicity Evaluation of Pig Slurry Using Luminescent Bacteria and Zebrafish

    PubMed Central

    Chen, Wenyan; Cai, Qiang; Zhao, Yuan; Zheng, Guojuan; Liang, Yuting

    2014-01-01

    Biogas slurry has become a serious pollution problem and anaerobic digestion is widely applied to pig manure treatment for environmental protection and energy recovery. To evaluate environmental risk of the emission of biogas slurry, luminescent bacteria (Vibrio fischeri), larvae and embryos of zebrafish (Danio rerio) were used to detect the acute and development toxicity of digested and post-treated slurry. Then the ability of treatment process was evaluated. The results showed that digested slurry displayed strong toxicity to both zebrafish and luminescent bacteria, while the EC50 for luminescent bacteria and the LC50 for larvae were only 6.81% (v/v) and 1.95% (v/v) respectively, and embryonic development was inhibited at just 1% (v/v). Slurry still maintained a high level of toxicity although it had been treated by membrane bioreactor (MBR), while the LC50 of larvae was 75.23% (v/v) and there was a little effect on the development of embryos and V. fischeri; the results also revealed that the zebrafish larvae are more sensitive than embryos and luminescent bacteria to pig slurry. Finally, we also found the toxicity removal rate was higher than 90% after the treatment of MBR according to toxicity tests. In conclusion, further treatment should be used in pig slurry disposal or reused of final effluent. PMID:24995598

  2. Pig slurry acidification and separation techniques affect soil N and C turnover and N2O emissions from solid, liquid and biochar fractions.

    PubMed

    Gómez-Muñoz, B; Case, S D C; Jensen, L S

    2016-03-01

    The combined effects of pig slurry acidification, subsequent separation techniques and biochar production from the solid fraction on N mineralisation and N2O and CO2 emissions in soil were investigated in an incubation experiment. Acidification of pig slurry increased N availability from the separated solid fractions in soil, but did not affect N2O and CO2 emissions. However acidification reduced soil N and C turnover from the liquid fraction. The use of more advanced separation techniques (flocculation and drainage > decanting centrifuge > screw press) increased N mineralisation from acidified solid fractions, but also increased N2O and CO2 emissions in soil amended with the liquid fraction. Finally, the biochar production from the solid fraction of pig slurry resulted in a very recalcitrant material, which reduced N and C mineralisation in soil compared to the raw solid fractions.

  3. Anaerobic digestion of sulfate-acidified cattle slurry: One-stage vs. two-stage.

    PubMed

    Moset, Veronica; Ottosen, Lars Ditlev Mørck; Xavier, Cristiane de Almeida Neves; Møller, Henrik Bjarne

    2016-05-15

    Two strategies to include acidified cattle manure (AcCM) in co-digestion with normal cattle manure (CM) are presented in this work. The strategies are a single thermophilic (50 °C) continuous stirred tank reactor (CSTR) anaerobic digestion and a two-step (65 °C + 50 °C) CSTR process. In both strategies, two different inclusion levels of H2SO4-acidified CM (10% and 20%) in co-digestion with normal CM were tested and compared with a control CSTR fed only CM. Important enhancement of methane (CH4) yield and solid reductions were observed in the thermophilic one-step CSTR working with 10% AcCM. However, a higher inclusion level of AcCM (20%) caused volatile fatty acid accumulation in the reactor and a more than 30% reduction in CH4 production. In terms of CH4 production, when 10% of AcCM was co-digested with 90% of CM, the two-step anaerobic co-digestion yielded less than the single step. During the first step of the two-step CSTR process, acidogenesis and a partial sulfate reduction were achieved. However, sulfide stripping between the first and the second step must be promoted in order to advance this technology.

  4. The role of heterotrophic microorganism Galactomyces sp. Z3 in improving pig slurry bioleaching.

    PubMed

    Zhou, Jun; Zheng, Guanyu; Zhou, Lixiang; Liu, Fenwu; Zheng, Chaocheng; Cui, Chunhong

    2013-01-01

    The feasibility of removing heavy metals and eliminating pathogens from pig slurry through bioleaching involving the fungus Galactomyces sp. Z3 and two acidophilic thiobacillus (A. ferrooxidans LX5 and A. thiooxidans TS6) was investigated. It was found that the isolated pig slurry dissolved organic matter (DOM) degrader Z3 was identified as Galactomyces sp. Z3, which could grow well at pH 2.5-7 and degrade pig slurry DOM from 1973 to 942 mg/l within 48 h. During the successive multi-batch bioleaching systems, the co-inoculation of pig slurry degrader Galactomyces sp. Z3 and the two Acidithiobacillus species could improve pig slurry bioleaching efficiency compared to the single system without Galactomyces sp. Z3. The removal efficiency of Zn and Cu exceeded 94% and 85%, respectively. In addition, the elimination efficiencies of pathogens, including both total coliform and faecal coliform counts, exceeded 99% after bioleaching treatment. However, the counts of Galactomyces sp. Z3 decreased with the fall of pH and did not restore to the initial level during successive multi-batch bioleaching systems, and it is necessary to re-inoculate Galactomyces sp. Z3 cells into the bioleaching system to maintain its role in degrading pig slurry DOM. Therefore, a bioleaching technique involving both Galactomyces sp. Z3 and Acidithiobacillus species is an efficient method for removing heavy metals and eliminating pathogens from pig slurry.

  5. Sorption of 17β-estradiol to pig slurry separates and soil in the soil-slurry environment.

    PubMed

    Amin, M G Mostofa; Petersen, Søren O; Lægdsmand, Mette

    2012-01-01

    Contamination of freshwater by estrogens from manure applied to agricultural land is of grave concern because of the potentially harmful effects on aquatic life and human health. Recent developments in liquid manure (slurry) management include partial removal of particulate slurry dry matter (PSDM) by separation technologies, which may also remove parts of the estrogens and enhance infiltration of the slurry on field application and hence the interaction between estrogens and the soil matrix. This study investigated how 17β-estradiol (E2), a natural estrogen commonly found in pig manure, sorbs to agricultural soils, to different size fractions of pig slurry separates, and to soils amended with each size fraction to simulate conditions in the soil-slurry environment. A crude fiber fraction (SS1) was prepared by sieving (<500 μm) the solids removed by an on-farm separation process. Three other size fractions (SS2 > SS3 > SS4) were prepared from the liquid fraction of the separated slurry by sedimentation and centrifugation. Sorption experiments were conducted in 0.01 mol L(-1) CaCl(2) and in natural pig urine matrix. Sorption in 0.01 mol L(-1) CaCl(2) was higher than that in pig urine for all solids used. Sorption of E2 to soil increased with its organic carbon content for both liquid phases. The solid-liquid partition coefficients of slurry separates were 10 to 30 times higher than those of soils, but the organoic carbon normalized partition coefficient values, reflecting sorption per unit organic carbon, were lower for slurry separates. Mixing slurry separates with soil increased the sorption of E2 to the solid phase significantly in the order: SS1 < SS3 < SS2 for both liquid phases. In contrast, SS4 reduced the sorption of E2 to the solid phase by increasing the sorption to suspended or dissolved organic matter. The study suggested that potentially 50 to 75% of E2 in slurry can be removed from the liquid fraction of slurry by physical separation.

  6. Greenhouse Gas and Ammonia Emissions from Slurry Storage: Impacts of Temperature and Potential Mitigation through Covering (Pig Slurry) or Acidification (Cattle Slurry).

    PubMed

    Misselbrook, Tom; Hunt, John; Perazzolo, Francesca; Provolo, Giorgio

    2016-09-01

    Storage of livestock slurries is a significant source of methane (CH) and ammonia (NH) emissions to the atmosphere, for which accurate quantification and potential mitigation methods are required. Methane and NH emissions were measured from pilot-scale cattle slurry (CS) and pig slurry (PS) stores under cool, temperate, and warm conditions (approximately 8, 11, and 17°C, respectively) and including two potential mitigation practices: (i) a clay granule floating cover (PS) and (ii) slurry acidification (CS). Cumulative emissions of both gases were influenced by mean temperature over the storage period. Methane emissions from the control treatments over the 2-mo storage periods for the cool, temperate, and warm periods were 0.3, 0.1, and 34.3 g CH kg slurry volatile solids for CS and 4.4, 20.1, and 27.7 g CH kg slurry volatile solids for PS. Respective NH emissions for each period were 4, 7, and 12% of initial slurry N content for CS and 12, 18, and 28% of initial slurry N content for PS. Covering PS with clay granules reduced NH emissions by 77% across the three storage periods but had no impact on CH emissions. Acidification of CS reduced CH and NH emissions by 61 and 75%, respectively, across the three storage periods. Nitrous oxide emissions were also monitored but were insignificant. The development of approaches that take into account the influence of storage timing (temperature) and duration on emission estimates for national emission inventory purposes is recommended.

  7. Carbon dynamics in different soil types amended with pig slurry, pig manure and its biochar

    NASA Astrophysics Data System (ADS)

    Yanardag, Ibrahim H.; Zornoza, Raúl; Faz, Ángel; Büyükkiliç-Yanardaǧ, Asuman; Mermut, Ahmet R.

    2014-05-01

    Determining the structure and components of soil and soil organic matter is very important in terms of sustainable agriculture and forestry and greenhouse gases emissions. Organic management can increase labile C and N in the short-term, and total soil C and N in the long-term, but less is known about how management practices may affect soil organic C (SOC)quality and stability. Methods to improve the management of livestock slurries to reduce the environmental impact and carbon losses are gaining importance. There is a need to find the best wastes treatment which enhances soil fertility but also carbon sequestration, to mitigate the effects of global warming. The objective of this study was to assess the short-term changes in SOC pools, using raw pig slurry, the solid phase of pig slurry, and its biochar as amendment in different soil types (Regosol, Luvisol and Kastanozem). The three different amendments were applied at 5 g C kg-1 soil. An unamended soil for each type was used as control. Soils were incubated in triplicate for 60 days at 25ºC and at 55% of their water holding capacity. Samples were sampled to monitor the evolution of soil organic and inorganic carbon, recalcitrant carbon, soluble carbon, carbon mineralization, SOC thermal distribution (thermogravimetric analysis - differential scanning calorimetry - quadrupole mass spectrometry), and characterization of functional groups (Fourier transform infrared spectroscopy (FTIR)). Results showed that soils amended with raw pig slurry and the solid phase of the slurry showed higher values of soluble carbon, and higher carbon mineralization rates compared to biochar application, which showed values similar to controls. SOC increased at the end of incubation with biochar and the solid phase of the slurry applications in Kastanozem and Regosol. Thermogravimetric results showed an increased weight loss of the Regosol compared to Luvisol and Kastanozem, owing to the higher content of soil carbonates. Luvisol and

  8. Estimation of Methane Emissions from Slurry Pits below Pig and Cattle Confinements

    PubMed Central

    Petersen, Søren O.; Olsen, Anne B.; Elsgaard, Lars; Triolo, Jin Mi; Sommer, Sven G.

    2016-01-01

    Quantifying in-house emissions of methane (CH4) from liquid manure (slurry) is difficult due to high background emissions from enteric processes, yet of great importance for correct estimation of CH4 emissions from manure management and effects of treatment technologies such as anaerobic digestion. In this study CH4 production rates were determined in 20 pig slurry and 11 cattle slurry samples collected beneath slatted floors on six representative farms; rates were determined within 24 h at temperatures close to the temperature in slurry pits at the time of collection. Methane production rates in pig and cattle slurry differed significantly at 0.030 and 0.011 kg CH4 kg-1 VS (volatile solids). Current estimates of CH4 emissions from pig and cattle manure management correspond to 0.032 and 0.015 kg CH4 kg-1, respectively, indicating that slurry pits under animal confinements are a significant source. Fractions of degradable volatile solids (VSd, kg kg-1 VS) were estimated using an aerobic biodegradability assay and total organic C analyses. The VSd in pig and cattle slurry averaged 0.51 and 0.33 kg kg-1 VS, and it was estimated that on average 43 and 28% of VSd in fresh excreta from pigs and cattle, respectively, had been lost at the time of sampling. An empirical model of CH4 emissions from slurry was reparameterised based on experimental results. A sensitivity analysis indicated that predicted CH4 emissions were highly sensitive to uncertainties in the value of lnA of the Arrhenius equation, but much less sensitive to uncertainties in VSd or slurry temperature. A model application indicated that losses of carbon in VS as CO2 may be much greater than losses as CH4. Implications of these results for the correct estimation of CH4 emissions from manure management, and for the mitigation potential of treatments such as anaerobic digestion, are discussed. PMID:27529692

  9. Nutrient Status and Contamination Risks from Digested Pig Slurry Applied on a Vegetable Crops Field

    PubMed Central

    Zhang, Shaohui; Hua, Yumei; Deng, Liangwei

    2016-01-01

    The effects of applied digested pig slurry on a vegetable crops field were studied. The study included a 3-year investigation on nutrient characteristics, heavy metals contamination and hygienic risks of a vegetable crops field in Wuhan, China. The results showed that, after anaerobic digestion, abundant N, P and K remained in the digested pig slurry while fecal coliforms, ascaris eggs, schistosoma eggs and hookworm eggs were highly reduced. High Cr, Zn and Cu contents in the digested pig slurry were found in spring. Digested pig slurry application to the vegetable crops field led to improved soil fertility. Plant-available P in the fertilized soils increased due to considerable increase in total P content and decrease in low-availability P fraction. The As content in the fertilized soils increased slightly but significantly (p = 0.003) compared with control. The Hg, Zn, Cr, Cd, Pb, and Cu contents in the fertilized soils did not exceed the maximum permissible contents for vegetable crops soils in China. However, high Zn accumulation should be of concern due to repeated applications of digested pig slurry. No fecal coliforms, ascaris eggs, schistosoma eggs or hookworm eggs were detected in the fertilized soils. PMID:27058548

  10. Assessment of Bacterial Community Assembly Patterns and Processes in Pig Manure Slurry

    PubMed Central

    Kumari, Priyanka; Choi, Hong L.; Sudiarto, Sartika I. A.

    2015-01-01

    The bacterial community assembly patterns and processes are poorly understood in pig manure slurry. We collected pig manure slurry samples during the winter and summer seasons from eight commercial pig farms in South Korea. The V3 region of 16S rRNA genes was PCR amplified and sequenced using paired-end Illumina technology for in-depth characterization of bacterial community. Firmicutes, Bacteroidetes, Proteobacteria, Spirochaetes, and Tenericutes were the predominant bacterial phyla present in slurry samples. Bacterial taxonomic community composition was not influenced by the season; however, phylogenetic community composition was affected by seasonal variations. The community composition and diversity patterns were strongly influenced by pH. The bacterial diversity indices showed a unimodal relationship with pH. Phylogenetic signals were detected over only short phylogenetic distances, revealing that closely related bacterial operational taxonomic units (OTUs) tend to co-occur in the same environment; hence, they are ecologically similar. Across all samples, a niche-based process, through strong environmental filtering imposed by pH, primarily governed bacterial community assembly; however, in samples close to the neutral pH range, the role of environmental filtering was decreased due to neutral community assembly. In summary, pH emerged as the major physico-chemical variable in pig manure slurry that regulates the relative importance of niche-based and neutral processes in shaping the community assembly of bacteria. PMID:26422375

  11. Benefits and limitations of pig slurry to reclaim bare mine soils under Mediterranean semiarid conditions

    NASA Astrophysics Data System (ADS)

    Zornoza, Raúl; Faz, Ángel; Acosta, Jose A.; Kabas, Sebla; Martínez-Martínez, Silvia; Ángeles Muñoz, M.

    2013-04-01

    In this study, the effects of pig slurry application on reclamation of mine soils from Cartagena-La Unión Mining District (SE Spain) were investigated in a field experiment. Exchangeable metals (Cd, Cu, Pb and Zn), total organic carbon, total nitrogen, soluble carbon, microbial biomass and three enzyme activities were periodically monitored during 67 days. In addition, one year after the application of the pig slurry, soil and developed vegetation was sampled. Results showed that only exchangeable Cd and Zn significantly decreased in the amended plots, mainly for Cd, with decreases of 98%. The rest of metals and chemical properties did not change with time after application of amendments, showing values not significantly different than those present before pig slurry application. Soluble carbon, microbial biomass carbon and the enzyme activities increased after the application of pig slurry. However, after various days these parameters started a decreasing trend until reaching values similar to the control from approximately day 25. Thus, mainly precipitation as phosphate from the waste was very effective for Cd immobilization. No increments were observed in soil organic carbon because the organic carbon applied with the slurry was too low to be significantly detected. Nonetheless, pig slurry is a good fertilizer owing to the high quantity of nutrients provided, needed to promote the development of vegetation. One year after application, a native vegetation cover (25-30%) was reached by spontaneous colonization. Triggered plant growth by the effect of amendment improved soil conditions, particularly by the help of the medium created by their rhizosphere systems. Increments in soil organic carbon and total nitrogen, and decreases in the exchangeable metals fraction concentration were observed in rhizospheric soils when compared to the bare soils. This improvement in soil quality mediated by vegetation was more efficient than the direct effect of the amendment. In

  12. Environmental evaluation of transfer and treatment of excess pig slurry by life cycle assessment.

    PubMed

    Lopez-Ridaura, Santiago; Werf, Hayo van der; Paillat, Jean Marie; Le Bris, Bertrand

    2009-02-01

    Slurry management is a central topic in the agronomic and environmental analysis of intensive livestock production systems. The objective of this study is to compare the environmental performance of two scenarios of collective slurry management for the disposal of excess nitrogen from animal manure. The scenarios are the transfer of slurry and its injection to crop land, and the treatment of slurry in a collective biological treatment station. The study is based on a real case in the West of France, where a group of farmers is developing a collective plan for the disposal of almost 7000 m(3) of excess pig slurry. The evaluation is carried out by Life Cycle Assessment, where emissions and resource consumption are quantified and aggregated into four environmental impact categories: eutrophication, acidification, climate change, and non-renewable energy use. Ammonia emitted is the most important contributor to acidification and eutrophication, while methane contributes most to climate change. Both ammonia and methane are mostly emitted during the storage of slurry and, in the case of the treatment scenario, also during composting the solid fraction of the slurry. The two management strategies are similar with respect to climate change, whereas eutrophication and acidification are twice as large for treatment relative to transfer. Electricity needed for the treatment process is the main contributor to non-renewable energy use for the treatment scenario, while the transfer scenario represents a net energy saving, as energy saved by the reduction of mineral fertiliser use more than compensates for the energy needed for transport and injection of slurry. The overall environmental performance of transfer is better than that of treatment, as it involves less acidification, eutrophication and non-renewable energy use. The method employed and the results obtained in this study can provide elements for a transparent discussion of the advantages and disadvantages of contrasting

  13. Survival of Salmonella spp. and fecal indicator bacteria in Vietnamese biogas digesters receiving pig slurry.

    PubMed

    Huong, Luu Quynh; Forslund, Anita; Madsen, Henry; Dalsgaard, Anders

    2014-09-01

    Small-scale biogas digesters are widely promoted worldwide as a sustainable technology to manage livestock manure. In Vietnam, pig slurry is commonly applied to biogas digesters for production of gas for electricity and cooking with the effluent being used to fertilize field crops, vegetables and fish ponds. Slurry may contain a variety of zoonotic pathogens, e.g. Salmonella spp., which are able to cause disease in humans either through direct contact with slurry or by fecal contamination of water and foods. The objective of this study was to evaluate the survival of Salmonella spp. and the fecal indicator bacteria, enterococci, E. coli, and spores of Clostridium perfringens in biogas digesters operated by small-scale Vietnamese pig farmers. The serovar and antimicrobial susceptibility of the Salmonella spp. isolated were also established. The study was conducted in 12 farms (6 farms with and 6 farms without toilet connected) located in Hanam province, Vietnam. Sampling of pig slurry and biogas effluent was done during two seasons. Results showed that the concentration of enterococci, E. coli, and Clostridium perfringens spores was overall reduced by only 1-2 log10-units in the biogas digesters when comparing raw slurry and biogas effluent. Salmonella spp. was found in both raw slurry and biogas effluent. A total of 19 Salmonella serovars were identified, with the main serovars being Salmonella Typhimurium (55/138), Salmonella enterica serovar 4,[5],12:i:- (19/138), Salmonella Weltevreden (9/138) and Salmonella Rissen (9/138). The Salmonella serovars showed similar antimicrobial resistance patterns to those previously reported from Vietnam. When promoting biogas, farmers should be made aware that effluent should only be used as fertilizer for crops not consumed raw and that indiscriminate discharge of effluent are likely to contaminate water recipients, e.g. drinking water sources, with pathogens. Relevant authorities should promote safe animal manure management

  14. Earthworm effects on gaseous emissions during vermifiltration of pig fresh slurry.

    PubMed

    Luth; Robin, Paul; Germain, Philippe; Lecomte, Marcel; Landrain, Brigitte; Li, Yinsheng; Cluzeau, Daniel

    2011-02-01

    Treatment of liquid manure can result in the production of ammonia, nitrous oxide and methane. Earthworms mix and transform nitrogen and carbon without consuming additional energy. The objective of this paper is to analyse whether earthworms modify the emissions of NH(3), N(2)O, CH(4) and CO(2) during vermifiltration of pig slurry. The experiment used mesocosms of around 50 L, made from a vermifilter treating the diluted manure of a swine house. Three levels of slurry were added to the mesocosms, with or without earthworms, during one month, in triplicate. Earthworm abundance and gas emissions were measured three and five times, respectively. There was a decrease in emissions of ammonia and nitrous oxide and a sink of methane in treatments with earthworms. We suggest that earthworm abundance can be used as a bioindicator of low energy input, and low greenhouse gas and ammonia output in systems using fresh slurry with water recycling.

  15. Slurry

    NASA Astrophysics Data System (ADS)

    Jiang, Ting; Lei, Hong

    2014-11-01

    With magnetic heads operating closer to hard disks, the hard disks must be ultra-smooth. The abrasive-free polishing (AFP) performance of cumene hydroperoxide (CHP) as the initiator in H2O2-based slurry for hard disk substrate was investigated in our work, and the results showed that the slurry including CHP could improve the material removal rate (MRR) and also reduce surface roughness. Electron spin-resonance spectroscopy (EPR), electrochemical measurement and Auger electron spectroscopy (AES) were conducted to investigate the acting mechanism with CHP during the polishing process. Compared with the H2O2 slurry, the EPR analysis shows that the CHP-H2O2 slurry provides a higher concentration of the HOO free radical. In addition, the AES analysis shows the oxidization reaction occurs in the external layer of the substrate surface. Furthermore, electrochemical measurements reveal that CHP can promote the electrochemical effect in AFP and lead to the increase of MRR.

  16. Microbial community dynamics in continuous microbial fuel cells fed with synthetic wastewater and pig slurry.

    PubMed

    Sotres, Ana; Tey, Laura; Bonmatí, August; Viñas, Marc

    2016-10-01

    Two-chambered microbial fuel cells (MFCs) operating with synthetic wastewater and pig slurry were assessed. Additionally, the use of 2-bromoethanesulfonate (BES-Inh) was studied. The synthetic wastewater-fed MFC (MFCSW) showed a maximum power density (PDmax) of 2138mWm(-3), and the addition of BES-Inh (10mM) did not show any improvement in its performance (PDmax=2078mWm(-3)). When pig slurry was used as feed (MFCPS), PDmax increased up to 5623mWm(-3). The microbial community composition was affected by the type of substrate used. While, Pseudomonadaceae and Clostridiaceae were the most representative families within the acetate-based medium, Flavobacteriaceae, Chitinophagaceae, Comamonadaceae and Nitrosomonadaceae were predominant when pig slurry was used as feed. Otherwise, only the Eubacterial microbial community composition was strongly modified when adding BES-Inh, thus leading to an enrichment of the Bacteroidetes phylum. Oppositely, the Archaeal community was less affected by the addition of BES-Inh, and Methanosarcina sp., arose as the predominant family in both situations. Despite all the differences in microbial communities, 6 operational taxonomic units (OTUs) belonging to Bacteroidetes (Porphyromonadaceae and Marinilabiaceae) and Firmicutes (Clostridiales) were found to be common to both MFCs, also for different contents of COD and N-NH4(+), and therefore could be considered as the bioanode core microbiome.

  17. Fate of phosphorus from biological aerobic treatment of pig slurry. By-products characterization and recovery.

    PubMed

    Daumer, M L; Beline, F; Guiziou, F

    2003-11-01

    The fate of phosphorus distribution in the products obtained from biological aerobic treatment of pig slurry, e.g. separated solids, liquid effluent and sludge, was monitored in three different farm-scale units. Samples of raw slurry, solid products, aerated slurry, liquid effluent and sludge were characterised and analysed for their concentration in total phosphorus, nitrogen content and heavy metals (Cu and Zn). At each treatment stage, nitrogen, phosphorus and heavy metals mass balance between input and output was established. Moreover, liquid products were characterised and analysed both for their total and dissolved ortho-phosphate content. Separated solids, sludge and liquid effluent represented 5%, 15-40% and 75-83% of the mass of the raw slurry, respectively. A mechanical separation step prior to aeration allowed the export of 25-30% of total phosphorus for further use as organic fertiliser. A large amount of total phosphorus (e.g. 60-70%) was located in sludge while phosphorus remaining in liquid effluent was about 15-25%. Raw slurry separation and sufficient aeration allowed phosphorus to concentrate in the sludge. Insufficient aeration resulted in the release of phosphorus as dissolved ortho-phosphate within the liquid effluent. Finally, relevance of the agronomic use of the products was discussed and improvements of biological aerobic treatment to enhance phosphorus removal and/or recovery were considered.

  18. Carbon dynamics in an almond orchard soil amended with raw and treated pig slurry

    NASA Astrophysics Data System (ADS)

    Domínguez, Sara G.; Zornoza, Raúl; Faz, Ángel

    2010-05-01

    In SE Spain, intensive farming is very common which supposes the generation of great amounts of pig slurries. These residues cause many storage problems due to their pollution capacity. A good management of them is necessary to avoid damages to the environment. The use of this effluent as fertilizer is a usual practice that in the correct dose is a good amend and important for sustainable development, but in excess can be a risk of polluting and damaging soil, water and crop conditions. Pig slurry is a source of many nutrients and specially rich in organic matter. The main objective of this study is to determine changes in soil organic carbon dynamics resulting from raw and treated slurry amendments applied in different doses. The experimental area is an almond orchard located in Cartagena (SE Spain). The climate of the area is semiarid Mediterranean with mean annual temperature of 18°C and mean annual rainfall of 275 mm. A total of 10 plots (12 m x 30 m) were designed, one of them being the control without fertilizer. Surface soil samples (0-25 cm) were collected in September 2009. Three different treatments were applied, raw slurry, the effluent obtained after solid-liquid separation and solid manure, all of them in three doses being the first one of 170 kg N/ha, (maximum permitted in nitrates directive 91/676/CEE), and the others two and three times the first one. Soil biochemical parameters are rapid indicators of changes in soil quality. According to this, total organic carbon, soil microbial biomass carbon, soluble carbon, and β-glucosidase, β-galactosidase and arylesterase activities were measured in order to assess some soil biochemical conditions and carbon dynamics in terms of the different treatments. As we expected, the use of these organic fertilizers rich in organic matter, had an effect on soil carbon and soil microbial activity resulting in an increase in most of the parameters; total organic carbon and β-galactosidase activity showed the

  19. Environmental assessment of nutrient recycling from biological pig slurry treatment--impact of fertilizer substitution and field emissions.

    PubMed

    Brockmann, Doris; Hanhoun, Mary; Négri, Ophélie; Hélias, Arnaud

    2014-07-01

    Pig slurry treatment is an important means in reducing nitrogen loads applied to farmland. Solid phase separation prior to biological treatment further allows for recovering phosphorus with the solid phase. The organic residues from the pig slurry treatment can be applied as organic fertilizers to farmland replacing mineral fertilizers. The environmental impacts of nutrient recycling from aerobic, biological pig slurry treatment were evaluated applying the life cycle assessment (LCA) methodology. LCA results revealed that direct field emissions from organic fertilizer application and the amount of avoided mineral fertilizers dominated the environmental impacts. A modified plant available nitrogen calculation (PAN) was introduced taking into account calculated nitrogen emissions from organic fertilizer application. Additionally, an equation for calculating the quantity of avoided mineral fertilizers based on the modified PAN calculation was proposed, which accounted for nitrogen emissions from mineral fertilizer application.

  20. Deodorization of pig slurry and characterization of bacterial diversity using 16S rDNA sequence analysis.

    PubMed

    Hwang, Ok-Hwa; Raveendar, Sebastian; Kim, Young-Ju; Kim, Ji-Hun; Choi, Jung-Woo; Kim, Tae-Hun; Choi, Dong-Yoon; Jeon, Che Ok; Cho, Sung-Back; Lee, Kyung-Tai

    2014-11-01

    The concentration of major odor-causing compounds including phenols, indoles, short-chain fatty acids (SCFAs) and branched chain fatty acids (BCFAs) in response to the addition of powdered horse radish (PHR) and spent mushroom compost (SMC) was compared with control non-treated slurry (CNS) samples. A total of 97,465 rDNAs sequence reads were generated from three different samples (CNS, n = 2; PHR, n = 3; SMC, n = 3) using bar-coded pyrosequencing. The number of operational taxonomic units (OTUs) was lower in the PHR slurry compared with the other samples. A total of 11 phyla were observed in the slurry samples, while the phylogenetic analysis revealed that the slurry microbiome predominantly comprised members of the Bacteroidetes, Firmicutes, and Proteobacteria phyla. The rarefaction analysis showed the bacterial species richness varied among the treated samples. Overall, at the OTU level, 2,558 individual genera were classified, 276 genera were found among the three samples, and 1,832 additional genera were identified in the individual samples. A principal component analysis revealed the differences in microbial communities among the CNS, PHR, and SMC pig slurries. Correlation of the bacterial community structure with the Kyoto Encyclopedia of Genes and Genomes (KEGG) predicted pathways showed that the treatments altered the metabolic capabilities of the slurry microbiota. Overall, these results demonstrated that the PHR and S MC treatments significantly reduced the malodor compounds in pig slurry (P < 0.05).

  1. Phosphorus, copper and zinc in solid and liquid fractions from full-scale and laboratory-separated pig slurry.

    PubMed

    Popovic, Olga; Hjorth, Maibritt; Jensen, Lars Stoumann

    2012-09-01

    Pig slurry separation is a slurry treatment technique that can reduce excess loads of P, Cu and Zn to the arable land. This study investigated the effects of different commercial and laboratory separation treatments for pig slurry on P, Cu and Zn distribution into solid and liquid fractions. Solid and liquid separation fractions were collected from two commercial separators installed on the farm. Five different separation treatments were performed (polymer flocculation and drainage; coagulation with iron sulphate addition and polymer flocculation and drainage; ozonation and centrifugation; centrifugation only; and natural sedimentation) on sow and suckling piglet raw slurry. Particle size fractionation was performed on raw slurry and all separation fractions by sequential wet sieving and P, Cu and Zn concentrations were then measured in the particle size classes. Dry matter and total P, Cu and Zn were separated with higher efficiency when chemical pretreatments with flocculants and coagulants were introduced before mechanical separation at both commercial and laboratory scale. When solid fractions are utilized as crop fertilizer (primarily as P fertilizer), the loads of Cu and Zn to the soils are not markedly different than the loads applied with raw slurry. When liquid fractions are used as crop fertilizer (primarily as N fertilizer), the loads of Cu and Zn are markedly lower than those supplied with raw slurry. The loads of Cu and Zn introduced to the soil were lowest on application of the liquid fraction produced by optimized separation treatments that included flocculation and coagulation.

  2. Nitrogen recovery from pig slurry in a two-chambered bioelectrochemical system.

    PubMed

    Sotres, A; Cerrillo, M; Viñas, M; Bonmatí, A

    2015-10-01

    Abiotic batch experiments showed that ammonia migration from anode to cathode was favored by an increase in voltage, from 39.9% to 44.6%, using synthetic media. A slight increase in ammonia migration was observed when using pig slurry, reaching a maximum of 49.9%. In a continuously MFC fed with pig slurry with a stripping/absorption unit coupled to the cathode chamber, the highest nitrogen flux (7.2 g N d(-1) m(-2)) was achieved using buffer as catholyte. Nitrogen flux increased to 10.3 g N d(-1) m(-2) when shifting to MEC mode. A clear improvement in nitrogen flux (25.5 g N d(-1) m(-2)) was observed when using NaCl as catholyte. Besides, ammonia stripping was favored, reaching a nitrogen recovery of 94.3% in the absorption column, due to the high pH reached in the cathode. The microbial community analysis revealed an enrichment of certain taxonomic Eubacterial and Archaeal groups when the system shifted from MFC to MEC mode.

  3. Pig slurry application and irrigation effects on nitrate leaching in Mediterranean soil lysimeters.

    PubMed

    Daudén, A; Quílez, D; Vera, M V

    2004-01-01

    Land application of animal manures, such as pig slurry (PS), is a common practice in intensive-farming agriculture. However, this practice has a pitfall consisting of the loss of nutrients, in particular nitrate, toward water courses. The objective of this study was to evaluate nitrate leaching for three application rates of pig slurry (50, 100, and 200 Mg ha(-1)) and a control treatment of mineral fertilizer (275 kg N ha(-1)) applied to corn grown in 10 drainage lysimeters. The effects of two irrigation regimes (low vs. high irrigation efficiency) were also analyzed. In the first two irrigation events, drainage NO(3)-N concentrations as high as 145 and 69 mg L(-1) were measured in the high and moderate PS rate treatments, respectively, in the low irrigation efficiency treatments. This indicates the fast transformation of the PS ammonium into nitrate and the subsequent leaching of the transformed nitrate. Drainage NO(3)-N concentration and load increased linearly by 0.69 mg NO(3)-N L(-1) and 4.6 kg NO(3)-N ha(-1), respectively, for each 10 kg N ha(-1) applied over the minimum of 275 kg N ha(-1). An increase in irrigation efficiency did not induce a significant increase of leachate concentration and the amount of nitrate leached decreased about 65%. Application of low PS doses before sowing complemented with sidedressing N application and a good irrigation management are the key factors to reduce nitrate contamination of water courses.

  4. Replacement of mineral fertilizers with anaerobically digested pig slurry in paddy fields: assessment of plant growth and grain quality.

    PubMed

    Zhang, Jin; Wang, Minyan; Cao, Yucheng; Liang, Peng; Wu, Shengchun; Leung, Anna Oi Wah; Christie, Peter

    2015-08-07

    Rice cultivation requires large quantities of irrigation water and mineral fertilizers. This provides an opportunity for the recycling of the plant nutrients in anaerobically digested pig slurry, large amounts of which are generated in Chinese pig farms. Hence, to promote the sustainable development of livestock and poultry breeding and rice production, a micro-plot field experiment was carried out to assess whether or not slurry can replace mineral fertilizers in rice paddy production in terms of plant tillering, grain quality, and yields. The results indicate that the total N content of the slurry can serve as an alternative source of N when compared to the control (450 kg ha(-1) commercial compound fertilizer (N/P2O5/K2O = 15:15:15) as basal fertilizer, 300 kg ha(-1) urea (N% = 46), and 150 kg ha(-1) commercial compound fertilizer as top-dressed fertilizer). No negative effects on plant growth or grain yield were observed, although there may be a potential risk due to an increase in grain Cu concentration. The amylose content and gel consistency of the rice grains were enhanced significantly by the use of slurry as a basal fertilizer, but the grain protein and total amino acid contents decreased. The results suggest that anaerobically digested pig slurry can replace mineral fertilizers in rice production when applied as a basal dressing together with urea and commercial compound fertilizer as top-dressed fertilizers.

  5. Modelling the potential of slurry management technologies to reduce the constraints of environmental legislation on pig production.

    PubMed

    Hutchings, Nicholas J; ten Hoeve, Marieke; Jensen, Rikke; Bruun, Sander; Søtoft, Lene F

    2013-11-30

    Limits on land applications of slurry nitrogen (N) and phosphorus (P) are used to restrict losses of nutrients caused by livestock production. Here, we used a model to assess technologies that enable a more even geographic distribution of slurry nutrients to land. Technologies included were screw press slurry separation, with or without solid fraction composting, centrifuge separation with or without liquid fraction ammonia (NH3) stripping, and anaerobic digestion. Regulatory constraints were placed first on the application in slurry of N, then P, then N and P both on the producing (donor) and receiving (recipient) farms. Finally, a constraint preventing an increase in donor farm NH3 emissions was imposed. Separation had little effect on N losses per unit mass of slurry, but NH3 stripping led to a reduction. Centrifuge separation allowed a greater increase in pig production than a screw press, especially with P regulation. NH3 stripping was only advantageous with N regulation or when combined with NH3 scrubbing of pig housing ventilation air, when donor farm NH3 emissions were a constraint. There was a production penalty for using composting or anaerobic digestion. The choice of appropriate slurry management option therefore depends on the focus of the regulation. Nuanced and therefore complex regulations are necessary to take advantage of synergies and avoid cross-policy conflicts and incongruencies.

  6. Radical change of Zn speciation in pig slurry amended soil: Key role of nano-sized sulfide particles.

    PubMed

    Formentini, Thiago Augusto; Legros, Samuel; Fernandes, Cristovão Vicente Scapulatempo; Pinheiro, Adilson; Le Bars, Maureen; Levard, Clément; Mallmann, Fábio Joel Kochem; da Veiga, Milton; Doelsch, Emmanuel

    2017-03-01

    Spreading livestock manure as fertilizer on farmlands is a widespread practice. It represents the major source of heavy metal(loid)s (HM) input in agricultural soils. Since zinc (Zn) is present at high concentrations in manure, it poses special environmental concerns related to phytotoxicity, groundwater contamination, and introduction in the food chain. Therefore, investigations on the fate and behavior of manure-borne Zn, when it enters the soil environment, are necessary to predict the environmental effects. Nevertheless, long-term field studies assessing Zn speciation in the organic waste matrix, as well as within the soil after manure application, are lacking. This study was designed to fill this gap. Using SEM-EDS and XAS analysis, we reported the following new results: (i) ZnS made up 100% of the Zn speciation in the pig slurry (the highest proportion of ZnS ever observed in organic waste); and (ii) ZnS aggregates were about 1-μm diameter (the smallest particle size ever reported in pig slurry). Moreover, the pig slurry containing ZnS was spread on the soil over an 11-year period, totaling 22 applications, and the resulting Zn speciation within the amended soil was analyzed. Surprisingly, ZnS, i.e. the only species responsible for a nearly 2-fold increase in the Zn concentration within the amended soil, was not detected in this soil. Based on SEM-EDS and XAS observations, we put forward the hypothesis that Zn in the pig slurry consisted of nano-sized ZnS crystallites that further aggregated. The low stability of ZnS nanoparticles within oxic and complex environments such as the studied soil was the key explanation for the radical change in pig slurry-borne Zn speciation after long-term amendments.

  7. Effect of natural zeolite (clinoptilolite) on microbial decomposition processes in stored pig-slurry solids.

    PubMed

    Vargová, M; Ondrasovicová, O; Sasáková, N; Ondrasovic, M; Novák, P; Krajnák, M

    1999-01-01

    The solid fraction (SF) of pig slurry obtained in the first stage of aerobic slurry treatment was amended with 1 and 2% zeolite (clinoptilolite) and stored for 12 weeks under anaerobic conditions or with turning after 3 and 6 weeks of storage. In addition to that SF was mixed with 2% zeolite, 50% (V/V) sawdust, and both sawdust and zeolite, and stored for 6 weeks with turning after 1 and 3 weeks. Plate counts of psychrophilic, mesophilic, coliform and fecal coliform bacteria, determined during the storage, corresponded to the development of temperature in the core of the substrates. An effect of amendment of SF with zeolite and sawdust on plate counts of selected bacteria was observed, dependent on the zeolite dose. The thermophilic phase was not reached in any of the investigated substrates. The populations of fecal coliforms in the substrate amended with 1% zeolite and turned after 3 and 6 weeks decreased after 11 weeks down to 500 CFU/g substrate.

  8. Response of maize yield, nitrate leaching, and soil nitrogen to pig slurry combined with mineral nitrogen.

    PubMed

    Yagüe, María R; Quílez, Dolores

    2010-01-01

    The application of pig (Sus scrofa) slurry (PS) is a common fertilization practice that may affect nitrate concentrations and loads in drainage and receiving water bodies. To protect water resources, many agricultural areas are being designated as vulnerable to nitrate contamination, and there is a need for scientific data aiming at reducing nitrate exports from these vulnerable zones by optimizing N fertilization strategies. The objective of this work, conducted in drainage lysimeters in a 4-yr monoculture maize (Zea mays L.) crop, is to assess the effects of four fertilization strategies combining PS (30, 60, 90, and 120 t ha(-1)) and mineral N on yield, changes in soil mineral N, and concentration and mass of nitrate in drainage waters. Grain yield was not affected by treatments in the four experimental years, nor was the soil mineral N at the end of the experiment. Effects of fertilization strategies on nitrate concentration and mass in drainage waters were detected only after 3 yr of repeated PS applications. The mass of nitrate leached over the 4 yr was positively related to the total amount of N applied, either organic or mineral. In year 2003, precipitation in spring reduced N availability for the crop in treatments with rates > or = 60 t PS ha(-1). The N-budget revealed that the transport pathways for 25% of N inputs to the system are unknown. The presowing application of pig slurry at 30 t ha(-1) complemented with mineral N at side-dressing, was the most efficient from an environmental standpoint (4-yr average of 145 kg grain yield kg(-1) N leached).

  9. Survival of free-living Acholeplasma in aerated pig manure slurry revealed by 13C-labeled bacterial biomass probing

    PubMed Central

    Hanajima, Dai; Aoyagi, Tomo; Hori, Tomoyuki

    2015-01-01

    Many studies have been performed on microbial community succession and/or predominant taxa during the composting process; however, the ecophysiological roles of microorganisms are not well understood because microbial community structures are highly diverse and dynamic. Bacteria are the most important contributors to the organic-waste decomposition process, while decayed bacterial cells can serve as readily digested substrates for other microbial populations. In this study, we investigated the active bacterial species responsible for the assimilation of dead bacterial cells and their components in aerated pig manure slurry by using 13C-labeled bacterial biomass probing. After 3 days of forced aeration, 13C-labeled and unlabeled dead Escherichia coli cell suspensions were added to the slurry. The suspensions contained 13C-labeled and unlabeled bacterial cell components, possibly including the cell wall and membrane, as well as intracellular materials. RNA extracted from each slurry sample 2 h after addition of E. coli suspension was density-resolved by isopycnic centrifugation and analyzed by terminal restriction fragment length polymorphism, followed by cloning and sequencing of bacterial 16S rRNA genes. In the heavy isotopically labeled RNA fraction, the predominant 13C-assimilating population was identified as belonging to the genus Acholeplasma, which was not detected in control heavy RNA. Acholeplasma spp. have limited biosynthetic capabilities and possess a wide variety of transporters, resulting in their metabolic dependence on external carbon and energy sources. The prevalence of Acholeplasma spp. was further confirmed in aerated pig manure slurry from four different pig farms by pyrosequencing of 16S rRNA genes; their relative abundance was ∼4.4%. Free-living Acholeplasma spp. had a competitive advantage for utilizing dead bacterial cells and their components more rapidly relative to other microbial populations, thus allowing the survival and prevalence

  10. Effects of long term raw pig slurry inputs on nutrient and metal contamination of tropical volcanogenic soils, Uvéa Island (South Pacific).

    PubMed

    Gunkel-Grillon, P; Roth, E; Laporte-Magoni, C; Le Mestre, M

    2015-11-15

    In small Polynesian islands, family pig breeding is usually conducted without recovery of pig slurry. Raw pig slurry is spread onto the soil without any treatment. So far, most of the studies were carried out in temperate climate and for industrial digested pig slurry applications on agricultural lands. In the present case study, conducted in Uvéa Island, the aim is to determine if long term application of raw pig slurry on tropical soils, naturally rich in heavy metals has a significant influence on elements concentrations and mobility. Two types of tropical soils and two pig breeding systems, pig enclosure on small concrete pens or pig enclosure in large land pens, were investigated. Here we demonstrate that raw pig slurry inputs on soils can lead to an increase of total nitrogen and phosphorus content with high Contamination Factors. The Pollution Load Index values (1.3; 5.3; 2.5; 2.3) were indicative of multi-heavy metals pollution (Fe, Mn, Al, Cu, Zn, Cr and Ni) in mixed calcareous soils of the coastal area and they are exchangeable while they are immobilized or less mobile in inland pure ferralitic soils. For mixed calcareous soils of the coastal area, family pig breeding represents a drainage risk of soluble species (phosphorus, inorganic nitrogen, Fe, Mn, Al, Cu, Zn, Cr and Ni). For inland ferralitic soils, family pig breeding is more compatible with a sustainable management of the environment in Uvéa Island and by extension in volcanic tropical islands with respect to the investigated chemical elements.

  11. Composting of the solid fraction of digestate derived from pig slurry: Biological processes and compost properties.

    PubMed

    Tambone, Fulvia; Terruzzi, Laura; Scaglia, Barbara; Adani, Fabrizio

    2015-01-01

    The aim of this paper was to assess the characteristics of the solid fractions (SF) obtained by mechanical separation of digestate, their compostability and compost quality. To do so, the SF of digestates obtained from anaerobic digestion of pig slurry, energy crops and agro-industrial residues were sampled in five plants located in Northern Italy. Results obtained indicated that anaerobic digestion by itself promoted the high biological stability of biomasses with a Potential Dynamic Respiration Index (PDRI) close to 1000 mgO2 kg V S(-1)h(-1). Subsequent composting of digestates, with an added bulking agent, did not give remarkably different results, and led only to a slight modification of the characteristics of the initial non-composted mixtures; the composts obtained fully respected the legal limits for high quality compost. Chemical studies of organic matter composition of the biomasses by using CP MAS (13)C NMR, indicated that the compost was composed of a high relative content of O-alkyl-C (71.47% of total C) (cellulose and hemicelluloses) and a low alkyl-C (12.42%) (i.e. volatile fatty acids, steroid-like molecules, aliphatic biopolymers and proteins).

  12. A full-scale study of treatment of pig slurry by composting: kinetic changes in chemical and microbial properties.

    PubMed

    Ros, M; García, C; Hernández, T

    2006-01-01

    Since the indiscriminate disposal of pig slurry can cause not only air pollution and bad odours but also nutrient pollution of ground waters and superficial waters, composting is sometimes used as one environmentally acceptable method for recycling pig manure. The aim of this study was to evaluate the effect of composting pig slurry on its sanitation (evaluated by ecotoxicity assays and pathogen content determination), as well as to determine the effect of a carbon-rich bulking agent (wood shavings, WS) and the starting C/N ratio on the changes undergone by different chemical (volatile organic matter, C and N fractions) and microbiological (microbial biomass C, ATP, dehydrogenase activity, urease, protease, phosphatase, and beta-glucosidase activities) parameters during composting. Pig slurry mixed with bulking agent (P+WS) and the solid faction separated from it, both with (PSF+WS) and without bulking agent (PSF), were composted for 13 weeks. Samples for analysis were taken from composting piles at the start of the process and at 3, 6, 9, and 13 weeks after the beginning of composting. The total organic carbon, water soluble C and ammonium content decreased with composting, while Kjeldahl N and nitrate content increased. The nitrification process in the PSF+WS pile was more intense than in the PSF or P+WS composting piles. The pathogen content decreased with composting, as did phytotoxic compounds, while the germination index increased with compost age. Piles with bulking agent showed higher values of basal respiration, microbial biomass carbon, ATP and hydrolase activities during the composting process than piles without bulking agent.

  13. Survival of model bacterial strains and helminth eggs in the course of mesophilic anaerobic digestion of pig slurry.

    PubMed

    Juris, P; Tóth, F; Lauková, A; Plachý, P; Dubinský, P; Sokol, J

    1996-05-01

    The effect of methanogenesis on the survival of model bacterial strains (Escherichia coli EC 5, Staphylococcus aureus SA 11, Enterococcus faecium CCM 4231) and non-embryonated helminth eggs (Ascaris suum) was investigated in pig slurry. Two pilot-plant experiments were carried out in two anaerobic digesters (800 and 1,000 litre) in a mesophilic thermal range (35-37 degrees C). The mean hydraulic retention time of the digesters was 20 days. The methanogenesis process was monitored by determining the following chemical parameters: pH, N-NH3, total dry matter (kg/day), organic matter (kg/day) production of methane by supplied and degraded organic matter (m3/kg). The results obtained allow us to state that the anaerobic stabilization of pig slurry in the mesophilic temperature range resulted in total devitalization of model bacterial strains E. coli EC 5 and Ent. faecium CCM 4231. St. aureus SA 11 cells, exposed to the above mentioned conditions, were also reduced in their number from 10.04 to 3.27 and from 8.69 to 2.77 log cfu/ml. It is assumed that the longer retention time of excrements in the digester could also result in total devitalization of St. aureus SA 11 cells. From the microbiological point of view, the above mentioned facts indicate a sufficient hygienization effect of the anaerobic fermentation on the contaminated pig excrements. The survival of A. suum eggs was little affected by the 20-day anaerobic mesophilic digestion of pig slurry. Only 17 or 18% (F1, F2) of the non-embryonated A. suum eggs were damaged after the 20-day exposure.

  14. Effect of fertilising with pig slurry and chicken manure on GHG emissions from Mediterranean paddies.

    PubMed

    Maris, S C; Teira-Esmatges, M R; Bosch-Serra, A D; Moreno-García, B; Català, M M

    2016-11-01

    Soil fertilisation affects greenhouse gas emissions. The objective of this study was to compare the effect of different fertilisation strategies on N2O, CH4 emissions and on ecosystem respiration (CO2 emissions), during different periods of rice cultivation (rice crop, postharvest period, and seedling) under Mediterranean climate. Emissions were quantified weekly by the photoacoustic technique at two sites. At Site 1 (2011 and 2012), background treatments were 2 doses of chicken manure (CM): 90 and 170kgNH4(+)-Nha(-1) (CM-90, CM-170), urea (U, 150kgNha(-1)) and no-N (control). Fifty kilogram N ha(-1) ammonium sulphate (AS) were topdress applied to all of them. At Site 2 (2012), background treatments were 2 doses of pig slurry (PS): 91 and 152kgNH4(+)-Nha(-1) (PS-91, PS-152) and ammonium sulphate (AS) at 120kgNH4(+)-Nha(-1) and no-N (control). Sixty kilogram NH4(+)-Nha(-1) as AS were topdress applied to AS and PS-91. During seedling, global warming potential (GWP) was ~3.5-17% of that of the whole rice crop for the CM treatments. The postharvest period was a net sink for CH4, and CO2 emissions only increased for the CM-170 treatment (up to 2MgCO2ha(-1)). The GWP of the entire rice crop reached 17Mg CO2-eqha(-1) for U, and was 14 for CM-170, and 37 for CM-90. The application of PS at agronomic doses (~170kgNha(-1)) allowed high yields (~7.4Mgha(-1)), the control of GWP (~6.5MgCO2-eqha(-1)), and a 13% reduction in greenhouse gas intensity (GHGI) to 0.89kgCO2-eqkg(-1) when compared to AS (1.02kgCO2-eqkg(-1)).

  15. Composting of the solid fraction of digestate derived from pig slurry: Biological processes and compost properties

    SciTech Connect

    Tambone, Fulvia Terruzzi, Laura; Scaglia, Barbara; Adani, Fabrizio

    2015-01-15

    Highlights: • Anaerobic digestion leads to the production of a biologically stable digestate. • Solid–liquid separation produces a solid fraction having high fertilizer value. • Composting process shows low biological activity due to high biological stability of digestate. • Solid digestate fraction can be composted in a short time or used directly as organic fertilizer. - Abstract: The aim of this paper was to assess the characteristics of the solid fractions (SF) obtained by mechanical separation of digestate, their compostability and compost quality. To do so, the SF of digestates obtained from anaerobic digestion of pig slurry, energy crops and agro-industrial residues were sampled in five plants located in Northern Italy. Results obtained indicated that anaerobic digestion by itself promoted the high biological stability of biomasses with a Potential Dynamic Respiration Index (PDRI) close to 1000 mgO{sub 2} kg V S{sup −1} h{sup −1}. Subsequent composting of digestates, with an added bulking agent, did not give remarkably different results, and led only to a slight modification of the characteristics of the initial non-composted mixtures; the composts obtained fully respected the legal limits for high quality compost. Chemical studies of organic matter composition of the biomasses by using CP MAS {sup 13}C NMR, indicated that the compost was composed of a high relative content of O-alkyl-C (71.47% of total C) (cellulose and hemicelluloses) and a low alkyl-C (12.42%) (i.e. volatile fatty acids, steroid-like molecules, aliphatic biopolymers and proteins)

  16. Effect of Storage Period on the Changes of Odorous Compound Concentrations and Bacterial Ecology for Identifying the Cause of Odor Production from Pig Slurry

    PubMed Central

    Hwang, Ok Hwa; Cho, Sung Back; Han, Deug Woo; Lee, Sang Ryoung; Kwag, Jeong Hoon; Park, Sung Kwon

    2016-01-01

    Odor from buildings where pigs are housed is generated by anaerobic fermentation of undigested materials in pig slurry stored for several weeks in pit. The objective of this study was to investigate the effect of storage period on the level of odorous compounds in pig slurry and on its bacterial community. A slurry sample (15 L) was taken from the pit of a finisher pig building and incubated in acryl chambers for six- weeks. Slurry for analysis was sampled every two-week. Levels of odorous compounds in the slurry sample were drastically changed after two weeks of storage period; levels of phenols and short chain fatty acids (SCFAs) were decreased (P<0.05), whereas indoles and branched-chain fatty acids (BCFAs) were increased (P<0.05). Among dominant bacteria, Bacteroides and Porphyromonadacese_uc_g revealed a strong positive correlation with the levels of phenols and SCFAs. Populations of AC160630_g, Acholeplasmatales_uc_g, Mollicutes_uc_g and Cloacamonas_f_uc_g positively correlated with indole and BCFAs content. Taken together, levels of odorous compounds were increased after two weeks of storage, possibly because of changes in the predominant bacterial groups to those that use protein as a carbon source in the hypo-carbohydrate conditions. PMID:27642752

  17. On-farm measurement of electrical conductivity for the estimation of ammonium nitrogen concentration in pig slurry.

    PubMed

    Yagüe, M R; Quílez, D

    2012-01-01

    Pig (Sus scrofa domesticus) slurry (PS) is commonly applied as fertilizer to agricultural fields. Knowledge of PS nitrogen content is essential for good management, but PS nitrogen content is highly variable, not only between farms but also within a farm. Laboratory analysis of animal slurries is often expensive and impractical for routine farmer use. Therefore, when slurry is spread on land, its fertilizer value is generally unknown, resulting in the risk of pollution. In this work, two rapid and suitable for field use methods for determining PS ammonium N (NH(4)+-N) concentration (Quantofix and conductimetry) are evaluated. The electrical conductivity of a dilution 1 PS:9 distilled water had better results than Quantofix, did not need reagents, and gave a direct value of NH(4)+-N concentrations (range, 1.0-7.6 kg NH(4)+-N m(-3)). The conductimetry method allows the use of alternative waters with EC <1.9 dS m(-1) for dilution. This method is being introduced to farmers in northeast Spain to improve PS management and has been well received due to its low cost and ease of use.

  18. Increasing energy and lysine in diets for growing-finishing pigs in hot environmental conditions: consequences on performance, digestibility, slurry composition, and gas emission.

    PubMed

    Cerisuelo, A; Torres, A; Lainez, M; Moset, V

    2012-05-01

    The influence of dietary nutrient concentration on growth performance, manure composition, and gas emission was studied in pigs in hot environmental conditions. A total of 64 intact males and 64 females [(Landrace × Large White) × Pietrain] weighing 63.1 ± 9.7 kg were divided into 2 dietary treatments: high (HD: 14.39 MJ of DE/kg and 1.11% Lys) and low (LD: 13.97 MJ of DE/kg and 1.01% Lys) in energy and Lys contents. Pigs were allocated to 32 split-sex pens with 4 pigs/pen and 16 pens/treatment. Average productive performance was recorded for 41 d (phase 1). After phase 1, 12 females of 103.3 ± 3.15 kg (6 per treatment) were selected and housed individually, and feces and slurry were collected during 3 and 4 consecutive days, respectively, to calculate nutrient digestibility and measure gas emissions (phase 2). For gas emission measurements, slurry was pooled by treatment and stored for 76 d. Initial composition of slurry and pH were analyzed. Maximum and minimum temperatures registered in the barn throughout the growing period were 35.1 and 18.1°C, respectively. Animals fed the HD diet grew more efficiently than pigs fed the LD diet (G:F, 0.43 vs. 0.40; SEM = 0.01; P < 0.05). Fat digestibility was greater in HD compared with LD pigs (88.0 vs. 84.9%; SEM = 0.9; P < 0.05). Slurry from pigs fed the LD diet showed greater DM, OM, total N, and VFA contents than slurry from pigs fed the HD diet. Cumulative NH(3), CO(2), and especially CH(4) emissions were greater in the HD slurry compared with the LD slurry (192.4 vs. 210.g of NH(3)/m(3); 2,712 vs. 3,210 g of CO(2)/m(3); 1,502 vs. 2,647 mL of CH(4)/kg of OM). Increasing feed density in the present study led to a more efficient growth, a decreased nutrient concentration in the slurry, and a greater gas emission.

  19. Long-term Effect of Pig Slurry Application on Soil Carbon Storage, Quality and Yield Sustainability in Murcia Region, Spain

    NASA Astrophysics Data System (ADS)

    Büyükkılıç Yanardaǧ, Asuman

    2013-04-01

    Sustainability of agriculture is now a major global concern, especially since the 1980s. Soil organic matter is very important in the proper functions of the soil, which is also a good indicator of soil quality. This is due to its influence on many of the chemical, physical, and biological processes that control the capacity of a soil to perform properly. Understanding of nutrient supply through organic matter mineralization in agricultural systems is essential for maintaining long-term quality and productivity. The composition of pig manure will have a profound impact on soil properties, quality and crop yield when used in agriculture. We studied the effects of pig slurry (PS) application as an organic fertilizer, trying to determine the optimum amount that can be added to the soil, and the effect on soil properties, quality, and productivity. We applied 3 different doses on silty loam soils: Single (D1), Double (D2), Triple (D3) and unfertilized plots (C) served as controls. Samples were collected at two different levels, surface (0-30 cm) and subsurface (30-60 cm). D1 application dose, which is the agronomic rate of N-requirement (170 kg N/ha/yr) (European Directive 91/676/CEE), is very appropriate in term of sustainable agriculture and also can improve physical, chemical and biological soil properties. Therefore that the long-term use of PS with low dose may necessarily enhance soil quality in the long term. There are many factors to be considered when attempting to assess the overall net impact of a management practice on productivity. Additions of pig manure to soils at agronomic rates (170 kg N ha-1 yr-1) to match crop nutrient requirements are expected to have a positive impact on soil productivity. Therefore, the benefits from the use of application depend on the management of PS, carbon and environmental quality. However, PS have high micronutrient contents, and for this reason the application of high doses can pollute soils and damage human, animal and

  20. The impact of fouling on the process performance of the thermal treatment of pig slurry using tubular heat exchangers.

    PubMed

    Cunault, C; Burton, C H; Pourcher, A M

    2013-03-15

    The aim of this study was to determine the kinetics of fouling and their influence on the performance of a thermal treatment process used for sanitisation of pig slurry. Two temperatures (55 °C and 80 °C) were investigated. One trial was carried out at 55 °C and 80 °C in which the slurry was not re-circulated and one trial at 80 °C in which 100% or 50% of the slurry was re-circulated. Fouling of the heat exchangers was assessed by on-line monitoring of the drop in pressure, changes in treatment temperature, heat transfer coefficients, heat recycling rate, and energy consumption. Similar energy consumption of around 38 kWh m(-3) of effluent was observed at the two temperatures. The operating periods prior to excessive fouling or blockage were 18 days at 55 °C and four days at 80 °C. Recycling treated manure to obtain 50% dilution of the raw feed increased the viable operating period to 14 days at 80 °C but doubled energy consumption. At 55 °C, the significant drop in the target temperature (>7 °C) with fouling severely jeopardised the process. The nature of the decline in performance suggests that the main fouling mechanisms were bio-fouling at 55 °C and organic/mineral deposits at 80 °C. Recycling treated manure enabled the operating period to be extended but increased the total cost of heating. One hundred percent recycling showed that the fouling potential of the manure was largely eliminated after one thermal treatment, suggesting a pretreatment may be advantageous.

  1. Carbon mineralization, microbial activity and metal dynamics in tailing ponds amended with pig slurry and marble waste.

    PubMed

    Zornoza, Raúl; Faz, Ángel; Carmona, Dora M; Acosta, Jose A; Martínez-Martínez, Silvia; de Vreng, Arno

    2013-03-01

    A field experiment was set up in Cartagena-La Unión Mining District, SE Spain, aimed at evaluating the short-term effects of pig slurry (PS) amendment alone and together with marble waste (MW) on organic matter mineralization, microbial activity and stabilization of heavy metals in two tailing ponds. These structures pose environmental risk owing to high metals contents, low organic matter and nutrients, and null vegetation. Carbon mineralization, exchangeable metals and microbiological properties were monitored during 67 d. The application of amendments led to a rapid decrease of exchangeable metals concentrations, except for Cu, with decreases up to 98%, 75% and 97% for Cd, Pb and Zn, respectively. The combined addition of MW+PS was the treatment with greater reduction in metals concentrations. The addition of PS caused a significant increase in respiration rates, although in MW+PS plots respiration was lower than in PS plots. The mineralized C from the pig slurry was low, approximately 25-30% and 4-12% for PS and MW+PS treatments, respectively. Soluble carbon (Csol), microbial biomass carbon (MBC) and β-galactosidase and β-glucosidase activities increased after the application of the organic amendment. However, after 3d these parameters started a decreasing trend reaching similar values than control from approximately day 25 for Csol and MBC. The PS treatment promoted highest values in enzyme activities, which remained high upon time. Arylesterase activity increased in the MW+PS treatment. Thus, the remediation techniques used improved soil microbiological status and reduced metal availability. The combined application of PS+MW reduced the degradability of the organic compounds.

  2. Thermal and spectroscopic analysis of organic matter degradation and humification during composting of pig slurry in different scenarios.

    PubMed

    Martín-Mata, J; Lahoz-Ramos, C; Bustamante, M A; Marhuenda-Egea, F C; Moral, R; Santos, A; Sáez, J A; Bernal, M P

    2016-09-01

    In this work, different analytical techniques (thermal analysis, (13)C cross-polarization magic angle spinning (CPMAS) NMR and Fourier transform infrared (FT-IR) spectroscopy) have been used to study the organic matter changes during the co-composting of pig slurry with cotton gin waste. To ensure the validity of the findings, the composting process was developed in different scenarios: under experimental pilot plant conditions, using the static pile system, and under real conditions on a pig farm, using the turning pile system. Also, the thermal stability index (R1) was determined before and after an extraction with water, to evaluate the effect of eliminating water-soluble inorganic salts on the thermal analysis. The results of the thermal methods showed the degradation of the most labile organic matter during composting; R1 increased during composting in all piles, without any influence of the presence of water-soluble inorganic ions in the sample. The NMR showed a decrease in the abundance of the carbohydrate molecules and an increase in the aliphatic materials during composting, due to a concentration effect. Also, FT-IR spectroscopy was a useful technique to study the trends of polysaccharides and nitrate, as indicators of organic matter transformations during composting.

  3. Leaching of viruses and other microorganisms naturally occurring in pig slurry to tile drains on a well-structured loamy field in Denmark

    NASA Astrophysics Data System (ADS)

    Krog, Jesper S.; Forslund, Anita; Larsen, Lars E.; Dalsgaard, Anders; Kjaer, Jeanne; Olsen, Preben; Schultz, Anna Charlotte

    2017-02-01

    The amount of animal manure used in modern agriculture is increasing due to the increase in global animal production. Pig slurry is known to contain zoonotic bacteria such as E. coli, Salmonella spp. and Campylobacter spp., and viruses such as hepatitis E virus and group A rotavirus. Coliform bacteria, present in manure, have previously been shown to leach into tile drains. This poses a potential threat to aquatic environments and may also influence the quality of drinking water. As knowledge is especially scarce about the fate of viruses when applied to fields in natural settings, this project sets out to investigate the leaching potential of six different microorganisms: E. coli and Enterococcus spp. (detected by colony assay), somatic coliphages (using plaque assays), and hepatitis E virus, porcine circovirus type 2, and group A rotavirus (by real-time polymerase chain reaction). All six microorganisms leached through the soil entering the tile drains situated at 1-m depth the first day following pig slurry application. The leaching pattern of group A rotavirus differed substantially from the pattern for somatic coliphages, which are otherwise used as indicators for virus contamination. Furthermore, group A rotavirus was detected in monitoring wells at 3.5-m depth up to 2 months after pig slurry application. The detection of viral genomic material in drainage water and shallow groundwater signifies a potential hazard to human health that needs to be investigated further, as water reservoirs used for recreational use and drinking water are potentially contaminated with zoonotic pathogens.

  4. Combination of batch experiments with continuous reactor data for ADM1 calibration: application to anaerobic digestion of pig slurry.

    PubMed

    Girault, R; Rousseau, P; Steyer, J P; Bernet, N; Béline, F

    2011-01-01

    Modelling anaerobic digestion processes is a key aspect of studying and optimizing digesters and related waste streams. However, for the satisfactory prediction of biogas production and effluent characteristics, some parameters have to be calibrated according to the characteristics of the substrates. This article describes a calibration procedure for the IWA 'Anaerobic Digestion Model no. 1' applied to the modelling of a digester for treatment of pig slurry. The most sensitive parameters were selected and calibrated combining results from a continuous digester and from batch trials run with the sludge sampled from the digester and the addition of specific substrates. According to the sensitivity analysis, acetoclastic methanogenesis, acetogenesis of propionate and acidogenesis of sugars were identified as the main sensitive steps in our case. The calibration procedure led us to modify slightly acetogenesis of propionate kinetic. However, acetoclastic methanogenesis and acidogenesis of sugars kinetics were significantly reduced by decreasing km and increasing Ks. Indeed, for instance, a decrease of km_ac from 8 to 7 day(-1) combined with an increase of Ks_ac from 0.15 to 1.5 kgCOD/m3 was necessary. After calibration, ADM1 provides an accurate simulation of the continuous reactor results.

  5. Isolation and Characterization of a New Methanobacterium formicicum KOR-1 from an Anaerobic Digester Using Pig Slurry

    PubMed Central

    Battumur, Urantulkhuur; Yoon, Young-Man; Kim, Chang-Hyun

    2016-01-01

    A new methanogen was isolated from an anaerobic digester using pig slurry in South Korea. Only one strain, designated KOR-1, was characterized in detail. Cells of KOR-1 were straight or crooked rods, non-motile, 5 to 15 μm long and 0.7 μm wide. They stained Gram-positive and produced methane from H2+CO2 and formate. Strain KOR-1 grew optimally at 38°C. The optimum pH for growth was 7.0. The strain grew at 0.5% to 3.0% NaCl, with optimum growth at 2.5% NaCl. The G+C content of genomic DNA of strain KOR-1 was 41 mol%. The strain tolerated ampicillin, penicillin G, kanamycin and streptomycin but tetracycline inhibited cell growth. A large fragment of the 16S rRNA gene (~1,350 bp) was obtained from the isolate and sequenced. Comparison of 16S rRNA genes revealed that strain KOR–1 is related to Methanobacterium formicicum (98%, sequence similarity), Methanobacterium bryantii (95%) and Methanobacterium ivanovii (93%). Phylogenetic analysis of the deduced mcrA gene sequences confirmed the closest relative as based on mcrA gene sequence analysis was Methanobacterium formicicum strain (97% nucleic acid sequence identity). On the basis of physiological and phylogenetic characteristics, strain KOR-1 is proposed as a new strain within the genus Methanobacterium, Methanobacterium formicicum KOR-1. PMID:26949961

  6. Characteristics and composition of fouling caused by pig slurry in a tubular heat exchanger--recommended cleaning systems.

    PubMed

    Cunault, C; Coquinot, Y; Burton, C H; Picard, S; Pourcher, A M

    2013-03-15

    The structure and composition of the fouling deposits caused by pig slurry heated in a tubular heat exchanger were characterized to understand their formation and thus be able to minimize fouling and define effective routine cleaning methods. Two temperatures (55 °C and 80 °C) were investigated. Two types of fouling were identified: organic/mineral and biofilm. The first only formed at temperatures above 50 °C, often during the heating phase, and was the main problem encountered in treatments at 80 °C. Organic/mineral deposits formed a thin compact sub-layer and a thick porous top layer composed of 67-76% minerals, 9-15% proteins, 8-20% carbohydrates and 0-5% fats. Biofilms formed at temperatures between 25 °C and 70 °C in both the cooling and heating sections of the exchanger. This type of fouling predominated at temperatures below 55 °C. The biofilm covered a thin mineral base layer. Strongly acidic or alkaline washing cycle are recommended to clean Type I deposits, while in-line gas-rumbling is recommended for Type II fouling.

  7. Modeling field-scale vertical movement of zinc and copper in a pig slurry-amended soil in Brazil.

    PubMed

    Mallmann, Fábio Joel Kochem; dos Santos, Danilo Rheinheimer; Ceretta, Carlos Alberto; Cella, Cesar; Simůnek, Jirka; van Oort, Folkert

    2012-12-01

    Organic amendments often represent a source of trace metals (TMs) in soils, which may partly leach into the groundwater. The objectives of this study were (1) to validate Hydrus-2D for modeling the transport of Zn and Cu in an Alfisol amended with pig slurry (PS) by comparing numerical simulations and experimental field data, and (2) to model the next 50 years of TM movements under scenarios of suspended or continued PS amendments. First, between 2000 and 2008, we collected detailed Zn and Cu data from a soil profile in Santa Maria, Brazil. Two hypotheses about Zn and Cu reactivity with the solid phase were tested, considering physical, hydraulic, and chemical characteristics of six soil layers. Using a two-site sorption model with a sorption kinetic rate adjusted based on laboratory EDTA extractions, Hydrus simulations of the vertical TM transport were found to satisfactorily describe the soil Zn and Cu concentration profiles. Second, the long-term fate of Zn and Cu in the soil was assessed using the validated parameterized model. Numerical simulations showed that Zn and Cu did not present risks for groundwater pollution. However, future Cu accumulation in the surface soil layer would exceed the Brazilian threshold for agricultural soils.

  8. Evaluation of the slurry management strategy and the integration of the composting technology in a pig farm - Agronomical and environmental implications.

    PubMed

    Sáez, José A; Clemente, Rafael; Bustamante, M Ángeles; Yañez, David; Bernal, M Pilar

    2017-05-01

    The changes in livestock production systems towards intensification frequently lead to an excess of manure generation with respect to the agricultural land available for its soil application. However, treatment technologies can help in the management of manures, especially in N-surplus areas. An integrated slurry treatment system based on solid-liquid separation, aerobic treatment of the liquid and composting the solid fraction was evaluated in a pig farm (sows and piglets) in the South of Spain. Solid fraction separation using a filter band connected to a screw press had low efficiency (38%), which was greatly improved incorporating a rotatory sieve (61%). The depuration system was very efficient for the liquid, with total removal of 84% total solids, 87% volatile solids, and 98% phosphorus. Two composting systems were tested through mechanical turning of: 1- a mixture of solid fraction stored for 1 month after solid-liquid separation and cereal straw; 2- recently-separated solid fraction mixed with cotton gin waste. System 2 was recommended for the farm, as it exhibited a fast temperature rise and a long thermophilic phase to ensure compost sanitisation, and high recovery of nutrients (TN 77%, P and K > 85%) and organic matter (45%). The composts obtained were mature, stable and showed a high degree of humification of their organic matter, absence of phytotoxicity and concentrations of nutrients similar to other composts from pig manure or separated slurry solids. However, the introduction of slurry from piglets into the solid-liquid separation system should be avoided in order to reduce the content of Zn in the compost, which lowers its quality. The slurry separation followed by composting of the solid fraction using a passive windrow system, and aeration of the liquid phase, was the most recommendable procedure for the reduction of GHG emissions on the farm.

  9. Utilization of wasted sardine oil as co-substrate with pig slurry for biogas production--a pilot experience of decentralized industrial organic waste management in a Portuguese pig farm.

    PubMed

    Ferreira, L; Duarte, E; Figueiredo, D

    2012-07-01

    This work aimed to demonstrate in a pig farm and in real conditions, the possibilities to co-digest wasted sardine oil (WSO) and pig slurry (PS) at farm scale. A biogas mobile pilot plant, was set up in the farm and operated in real conditions during 4 months. Dynamic mesophilic (35-37 °C) continuous pilot trials were performed during four different periods of time. In each period a different organic loading rate (OLR) based on the chemical oxygen demand (COD) was operated sequentially, with pig slurry (PS) (OLR = 1.6 kg COD/m(3) d(-1)) and with mixtures of WSO:PS with a volumetric composition (% v/v) of 2:98 (OLR = 3.0 kg COD/m(3) d(-1)), 3:97 (OLR = 3.7 kg COD/m(3) d(-1)) and 5:95 (OLR = 5.2 kg COD/m(3) d(-1)). Biomass adapted very fast in metabolise the WSO and biogas productivity was raised substantially for different compositions of WSO:PS. Process stability indicators pH and Total volatile fatty acids/bicarbonate alkalinity (T-VFA/BA) ratio, suggests that the co-digestion process was robust. It was concluded that WSO could be easily co-digested in farm scale biogas plants.

  10. Impact of raw pig slurry and pig farming practices on physicochemical parameters and on atmospheric N2O and CH 4 emissions of tropical soils, Uvéa Island (South Pacific).

    PubMed

    Roth, E; Gunkel-Grillon, P; Joly, L; Thomas, X; Decarpenterie, T; Mappe-Fogaing, I; Laporte-Magoni, C; Dumelié, N; Durry, G

    2014-09-01

    Emissions of CH4 and N2O related to private pig farming under a tropical climate in Uvéa Island were studied in this paper. Physicochemical soil parameters such as nitrate, nitrite, ammonium, Kjeldahl nitrogen, total organic carbon, pH and moisture were measured. Gaseous soil emissions as well as physicochemical parameters were compared in two private pig farming strategies encountered on this island on two different soils (calcareous and ferralitic) in order to determine the best pig farming management: in small concrete pens or in large land pens. Ammonium levels were higher in control areas while nitrate and nitrite levels were higher in soils with pig slurry inputs, indicating that nitrification was the predominant process related to N2O emissions. Nitrate contents in soils near concrete pens were important (≥ 55 μg N/g) and can thus be a threat for the groundwater. For both pig farming strategies, N2O and CH4 fluxes can reach high levels up to 1 mg N/m(2)/h and 1 mg C/m(2)/h, respectively. CH4 emissions near concrete pens were very high (≥ 10.4 mg C/m(2)/h). Former land pens converted into agricultural land recover low N2O emission rates (≤ 0.03 mg N/m(2)/h), and methane uptake dominates. N2O emissions were related to nitrate content whereas CH4 emissions were found to be moisture dependent. As a result relating to the physicochemical parameters as well as to the gaseous emissions, we demonstrate that pig farming in large land pens is the best strategy for sustainable family pig breeding in Uvéa Islands and therefore in similar small tropical islands.

  11. Pig feeding strategy coupled with effluent management - fresh or stored slurry, solid phase separation - on methane potential and methane conversion factors during storage

    NASA Astrophysics Data System (ADS)

    Jarret, Guillaume; Martinez, José; Dourmad, Jean-Yves

    2011-11-01

    In the guideline for the determination of methane (CH 4) emission from animal manure (IPCC) the amount of CH 4 emitted is generally calculated according to an equation combining the amount of organic matter (OM) or volatile solids excreted, the ultimate CH 4 potential ( B0) of excreta and a system-specific methane conversion factor (MCF, %) that reflects the portion of B0 that is really converted into CH 4. The objective of the present study was to investigate the effect of the modification of dietary crude protein and fibre levels on B0 of pig slurry and on subsequent MCF according to different strategies of slurry management. Five experimental diets differing mainly in their crude protein and fibre content were compared. Two types of measurement of CH 4 emission were performed. The first was the measurement of B0 of slurry using biomethanogene potential (BMP) test. The second consisted in a storage simulation, which was performed on different kinds of effluents: fresh slurry (FSl), stored slurry (SSl), and faeces mixed with water (FaW). The type of diet and the type of effluent affected ( P < 0.001) CH 4 production after 30, 50 and 100 days. Moreover, the interaction between type of effluent and type of diet was significant for CH 4 emission and for MCF. CH 4 production was the highest for BMP, the average production of CH 4 during storage from FaW, FSl and SSl samples representing 77%, 58% and 64% of the B0 value. The dynamic of CH 4 production during BMP tests was rather similar for all dietary treatments whereas it differed for storage simulation studies with significant effects of dietary CP and fibre contents. The results from this study indicate that the type of diet has a significant but rather limited effect on B0 value of effluent. The effect of diet is much more marked on MCF, with lower values for high protein diets, and higher values for high fibre diets. MCF is also affected by manure management, the values measured on separated faeces from urine

  12. Nitrogen transformations under different conditions in open ponds by means of microalgae-bacteria consortium treating pig slurry.

    PubMed

    González-Fernández, Cristina; Molinuevo-Salces, Beatriz; García-González, Maria Cruz

    2011-01-01

    Four open ponds inoculated with microalgae-bacteria consortium treating different swine slurries (fresh and anaerobically digested) were evaluated in terms of nitrogen transformation under optimal and real conditions of temperature and illumination. Ammonium complete depletion was not achieved. Ponds operated under real conditions presented lower ammonium removal. Elimination capacities were around 26 mg N/Ld and were subsequently increased with increasing inlet ammonium loading rate. Different nitrogen transformation was observed depending on substrate source. When anaerobically digested slurry was fed to the ponds, nitrification followed by biomass uptake and denitrification were the main nitrogen transformation taking place depending on inlet ammonium loading rate and operational conditions. Ponds fed with fresh slurry exhibited denitrification as the main nitrogen removal mechanism for the pond operated under real conditions while under optimal conditions stripping, denitrification and biomass uptake contributed similarly. Therefore, this study confirmed that the so-claimed nitrogen recovery by microalgae biomass is frequently overestimated.

  13. Injection of Dicyandiamide-Treated Pig Slurry Reduced Ammonia Volatilization without Enhancing Soil Nitrous Oxide Emissions from No-Till Corn in Southern Brazil.

    PubMed

    Aita, Celso; Gonzatto, Rogério; Miola, Ezequiel C C; B, Daniela; Santos, Dos; Rochette, Philippe; Angers, Denis A; Chantigny, Martin H; Pujol, Stefen B; Giacomini, Diego A; Giacomini, Sandro J

    2014-05-01

    There is a lack of information on how placement in soil and nitrification inhibitors affects nitrous oxide (NO) and ammonia (NH) emissions from pig slurry (PS) applied under no-till (NT) conditions. Our objective was to determine the impact of injecting PS and treating it with the nitrification inhibitor dicyandiamide (DCD) on NH and NO emissions from soils under NT in subtropical southern Brazil. The emissions of these gases were compared for shallow (∼ 10 cm) injection and surface broadcasting of PS with and without DCD (8.1-10.0 kg ha; 6.5-8.4% of applied NH-N). Measurements were made at two sites during two summer growing seasons under NT corn crops. Injection reduced NH volatilization by 70% but increased NO emissions 2.4-fold (from 2628 to 6198 g NO N ha) compared with surface broadcast application. Adding DCD to PS inhibited nitrification and reduced NO emissions by an average of 28% (730 g NO-N ha) for surface broadcast and 66% (4105 g NO-N ha) for injection but did not increase NH volatilization. Consequently, NO emission factors were much higher for injection (3.6%) than for surface broadcast (1.3%) application and were reduced (0.9%) when DCD was added to injected PS. In conclusion, the injection of DCD-treated slurry is a recommendable practice for reducing NH and NO emissions when applying PS on NT corn in southern Brazil.

  14. Simulation with models of increasing complexity of CO2 emissions and nitrogen mineralisation, after soil application of labelled pig slurry and maize stalks

    NASA Astrophysics Data System (ADS)

    Bechini, Luca; Marino Gallina, Pietro; Geromel, Gabriele; Corti, Martina; Cavalli, Daniele

    2015-04-01

    High amounts of nitrogen are available per unit area in regions with intensive livestock operations. In swine farms, pig slurries are frequently incorporated in the soil together with maize stalks. Simulation models may help to understand nitrogen dynamics associated with animal manure and crop residue decomposition in the soil, and to support the definition of best management practices. The objective of this work was to test the ability of different models to simulate CO2 emissions and nitrogen mineralisation during a laboratory incubation (under optimal soil water content and constant temperature) of maize stalks (ST) and pig slurry (PS). A loam soil was amended with labelled (15N) or unlabelled maize stalks and pig slurries, in the presence of ammonium sulphate (AS). These treatments were established: unfertilised soil; ST15 + AS + PS; ST + AS15 + PS; and ST + AS + PS15. During 180 days, we measured CO2 emissions; microbial biomass C, N, and 15N; and soil mineral N (SMN and SM-15N). Three models of increasing complexity were calibrated using measured data. The models were two modifications of ICBM 2B/N (Kätterer and Andrén, 2001) and CN-SIM (Petersen et al., 2005). The three models simulated rather accurately the emissions of CO2 throughout the incubation period (Relative Root Mean Squared Error, RRMSE = 8-25). The simplest model (with one pool for ST and one for PS) strongly overestimated SMN immobilisation from day 3 to day 21, both in the treatments with AS15 and PS15 (RRMSE = 27-30%). The other two models represented rather well the dynamics of SMN in the soil (RRMSE = 21-25%), simulating a fast increase of nitrate concentration in the first days, and slower rates of nitrification thereafter. Worse performances were obtained with all models for the simulation of SM-15N in the treatment with ST15 (RRMSE = 64-104%): experimental data showed positive mineralization of stalk-derived N from the beginning of the incubation, while models strongly underestimated

  15. Degradation of sulfadiazine by Microbacterium lacus strain SDZm4, isolated from lysimeters previously manured with slurry from sulfadiazine-medicated pigs.

    PubMed

    Tappe, Wolfgang; Herbst, Michael; Hofmann, Diana; Koeppchen, Stephan; Kummer, Sirgit; Thiele, Björn; Groeneweg, Joost

    2013-04-01

    Sulfadiazine (SDZ)-degrading bacterial cultures were enriched from the topsoil layer of lysimeters that were formerly treated with manure from pigs medicated with (14)C-labeled SDZ. The loss of about 35% of the applied radioactivity after an incubation period of 3 years was attributed to CO2 release due to mineralization processes in the lysimeters. Microcosm experiments with moist soil and soil slurries originating from these lysimeters confirmed the presumed mineralization potential, and an SDZ-degrading bacterium was isolated. It was identified as Microbacterium lacus, denoted strain SDZm4. During degradation studies with M. lacus strain SDZm4 using pyrimidine-ring labeled SDZ, SDZ disappeared completely but no (14)CO2 was released during 10 days of incubation. The entire applied radioactivity (AR) remained in solution and could be assigned to 2-aminopyrimidine. In contrast, for parallel incubations but with phenyl ring-labeled SDZ, 56% of the AR was released as (14)CO2, 16% was linked to biomass, and 21% remained as dissolved, not yet identified (14)C. Thus, it was shown that M. lacus extensively mineralized and partly assimilated the phenyl moiety of the SDZ molecule while forming equimolar amounts of 2-aminopyrimidine. This partial degradation might be an important step in the complete mineralization of SDZ by soil microorganisms.

  16. Pelleted organo-mineral fertilisers from composted pig slurry solids, animal wastes and spent mushroom compost for amenity grasslands.

    PubMed

    Rao, Juluri R; Watabe, Miyuki; Stewart, T Andrew; Millar, B Cherie; Moore, John E

    2007-01-01

    In Ireland, conversion of biodegradable farm wastes such as pig manure spent mushroom compost and poultry litter wastes to pelletised fertilisers is a desirable option for farmers. In this paper, results obtained from the composting of pig waste solids (20% w/w) blended with other locally available biodegradable wastes comprising poultry litter (26% w/w), spent mushroom compost (26% w/w), cocoa husks (18% w/w) and moistened shredded paper (10% w/w) are presented. The resulting 6-mo old 'mature' composts had a nutrient content of 2.3% total N, 1.6% P and 3.1% K, too 'low' for direct use as an agricultural fertiliser. Formulations incorporating dried blood or feather meal amendments enriched the organic N-content, reduced the moisture in mature compost mixtures and aided the granulation process. Inclusion of mineral supplements viz., sulphate of ammonia, rock phosphate and sulphate of potash, yielded slow release fertilisers with nutrient N:P:K ratios of 10:3:6 and 3:5:10 that were suited for amenity grasslands such as golf courses for spring or summer application and autumn dressing, respectively. Rigorous microbiological tests carried out throughout the composting, processing and pelletising phases indicated that the formulated organo-mineral fertilisers were free of vegetative bacterial pathogens.

  17. 7 CFR 58.720 - Acidifying agents.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.720 Acidifying agents. Acidifying agents if used shall be those permitted by the Food...

  18. 7 CFR 58.720 - Acidifying agents.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.720 Acidifying agents. Acidifying agents if used shall be those permitted by the Food...

  19. 7 CFR 58.720 - Acidifying agents.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.720 Acidifying agents. Acidifying agents if used shall be those permitted by the Food...

  20. 7 CFR 58.720 - Acidifying agents.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.720 Acidifying agents. Acidifying agents if used shall be those permitted by the Food...

  1. 7 CFR 58.720 - Acidifying agents.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.720 Acidifying agents. Acidifying agents if used shall be those permitted by the Food...

  2. 21 CFR 131.111 - Acidified milk.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Acidified milk. 131.111 Section 131.111 Food and... CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.111 Acidified milk. (a) Description. Acidified milk is the food produced by souring one or more of the optional dairy...

  3. 21 CFR 131.111 - Acidified milk.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Acidified milk. 131.111 Section 131.111 Food and... CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.111 Acidified milk. (a) Description. Acidified milk is the food produced by souring one or more of the optional dairy...

  4. 21 CFR 131.111 - Acidified milk.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 2 2014-04-01 2014-04-01 false Acidified milk. 131.111 Section 131.111 Food and... CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.111 Acidified milk. (a) Description. Acidified milk is the food produced by souring one or more of the optional dairy...

  5. Acidification of animal slurry--a review.

    PubMed

    Fangueiro, David; Hjorth, Maibritt; Gioelli, Fabrizio

    2015-02-01

    Ammonia emissions are a major problem associated with animal slurry management, and solutions to overcome this problem are required worldwide by farmers and stakeholders. An obvious way to minimize ammonia emissions from slurry is to decrease slurry pH by addition of acids or other substances. This solution has been used commonly since 2010 in countries such as Denmark, and its efficiency with regard to the minimization of NH3 emissions has been documented in many studies. Nevertheless, the impact of such treatment on other gaseous emissions during storage is not clear, since the studies performed so far have provided different scenarios. Similarly, the impact of the soil application of acidified slurry on plant production and diffuse pollution has been considered in several studies. Also, the impact of acidification upon combination with other slurry treatment technologies (e.g. mechanical separation, anaerobic digestion …) is important to consider. Here, a compilation and critical review of all these studies has been performed in order to fully understand the global impact of slurry acidification and assess the applicability of this treatment for slurry management.

  6. 21 CFR 108.25 - Acidified foods.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Acidified foods. 108.25 Section 108.25 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... With an Emergency Permit § 108.25 Acidified foods. (a) Inadequate or improper manufacture,...

  7. 21 CFR 108.25 - Acidified foods.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Acidified foods. 108.25 Section 108.25 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... With an Emergency Permit § 108.25 Acidified foods. (a) Inadequate or improper manufacture,...

  8. 21 CFR 108.25 - Acidified foods.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 2 2014-04-01 2014-04-01 false Acidified foods. 108.25 Section 108.25 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... With an Emergency Permit § 108.25 Acidified foods. (a) Inadequate or improper manufacture,...

  9. Effect of Bacillus spp. direct-fed microbial on slurry characteristics and gaseous emissions in growing pigs fed with high fibre-based diets.

    PubMed

    Prenafeta-Boldú, F X; Fernández, B; Viñas, M; Lizardo, R; Brufau, J; Owusu-Asiedu, A; Walsh, M C; Awati, A

    2017-02-01

    A 26-day trial with 18 Pietrain×(Landrace×Duroc) pigs was conducted to investigate the effect of two dose levels of a specifically selected Bacillus spp. direct-fed microbial (DFM) product, on the emission of environmentally harmful gasses (methane, ammonia and hydrogen sulphide) from manure. Pigs were assigned to one of three treatments in a randomized complete block design according to their sex and initial BW. Each treatment contained three replications with two pigs per pen. The test treatments included a Bacillus spp. DFM containing 3×108 colony-forming unit/g, added at a low (250 mg/kg) and high (500 mg/kg) dose to an antibiotic free high fibre-based diet, and a non-supplemented control diet. Manure from pigs fed with the supplemented diets emitted lower amounts of atmospheric contaminants. The most significant reduction was observed with low DFM supplementation, in which methane and ammonia volatilization decreased (P40% and 50%, respectively, on fresh weight basis in relation to the control. Microbiome analysis of manure by high through put sequencing techniques on eubacterial and archaeal 16S rRNA genes highlighted the complex interactions between indigenous gut microflora and inoculated Bacillus spp. The tested Bacillus DFM could be considered as a best available technique in reducing the environmental impacts of growing pigs fed with high fibre-based diets.

  10. 21 CFR 131.111 - Acidified milk.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.111 Acidified milk. (a... ingredients. Cream, milk, partially skimmed milk, or skim milk, used alone or in combination. (d)...

  11. Filtering reprecipitated slurry

    SciTech Connect

    Morrissey, M.F.

    1992-01-01

    As part of the Late Washing Demonstration at Savannah River Technology Center, Interim Waste Technology has filtered reprecipitated and non reprecipitated slurry with the Experimental Laboratory Filter (ELF) at TNX. Reprecipitated slurry generates higher permeate fluxes than non reprecipitated slurry. Washing reprecipitated slurry may require a defoamer because reprecipitation encourages foaming.

  12. Filtering reprecipitated slurry

    SciTech Connect

    Morrissey, M.F.

    1992-12-31

    As part of the Late Washing Demonstration at Savannah River Technology Center, Interim Waste Technology has filtered reprecipitated and non reprecipitated slurry with the Experimental Laboratory Filter (ELF) at TNX. Reprecipitated slurry generates higher permeate fluxes than non reprecipitated slurry. Washing reprecipitated slurry may require a defoamer because reprecipitation encourages foaming.

  13. Microbiological Spoilage of Acidified Specialty Products

    NASA Astrophysics Data System (ADS)

    Sperber, William H.

    Acidified specialty products or condiments are among the most microbiologically stable and safe food products. Often formulated, packaged, and distributed without heat treatments, they are microbiologically stable indefinitely at ambient temperatures in unopened containers. The packaged, acidified products are often intended for multiple uses, exposing them at the points of consumption to numerous opportunities for contamination with microorganisms. Nonetheless, they remain resistant to microbiological spoilage for many months, often under refrigerated conditions that are used to retard chemical reactions, flavor changes, and yeast growth.

  14. Effects of cattle-slurry treatment by acidification and separation on nitrogen dynamics and global warming potential after surface application to an acidic soil.

    PubMed

    Fangueiro, David; Pereira, José; Bichana, André; Surgy, Sónia; Cabral, Fernanda; Coutinho, João

    2015-10-01

    Cattle-slurry (liquid manure) application to soil is a common practice to provide nutrients and organic matter for crop growth but it also strongly impacts the environment. The objective of the present study was to assess the efficiency of cattle-slurry treatment by solid-liquid separation and/or acidification on nitrogen dynamics and global warming potential (GWP) following application to an acidic soil. An aerobic laboratory incubation was performed over 92 days with a Dystric Cambisol amended with raw cattle-slurry or separated liquid fraction (LF) treated or not by acidification to pH 5.5 by addition of sulphuric acid. Soil mineral N contents and NH3, N2O, CH4 and CO2 emissions were measured. Results obtained suggest that the acidification of raw cattle-slurry reduced significantly NH3 emissions (-88%) but also the GWP (-28%) while increased the N availability relative to raw cattle-slurry (15% of organic N applied mineralised against negative mineralisation in raw slurry). However, similar NH3 emissions and GWP were observed in acidified LF and non-acidified LF treatments. On the other hand, soil application of acidified cattle-slurry rather than non-acidified LF should be preferred attending the lower costs associated to acidification compared to solid-liquid separation. It can then be concluded that cattle-slurry acidification is a solution to minimise NH3 emissions from amended soil and an efficient strategy to decrease the GWP associated with slurry application to soil. Furthermore, the more intense N mineralisation observed with acidified slurry should lead to a higher amount of plant available N and consequently to higher crop yields.

  15. 21 CFR 108.25 - Acidified foods.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN..., or packing of acidified foods may result in the distribution in interstate commerce of processed... after these foods have entered into interstate commerce. The Commissioner of Food and Drugs...

  16. Chemical behavior of acidified chromium (3) solutions

    SciTech Connect

    Terman, D.K.

    1981-05-01

    A unique energy-storage system has been developed at NASA's Lewis Research Center called REDOX. This NASA-REDOX system is an electrochemical storage device that utilized the oxidation and reduction of two fully soluble redox couples for charging and discharging. The redox couples now being investigated are acidified chloride solutions of chromium (Cr(+2)/Cr(+3)) and iron (Fe(+2)/Fe(+3)).

  17. 21 CFR 173.325 - Acidified sodium chlorite solutions.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... HUMAN CONSUMPTION Specific Usage Additives § 173.325 Acidified sodium chlorite solutions. Acidified...., College Park, MD 20740, or may be examined at the Center for Food Safety and Applied Nutrition's...

  18. 21 CFR 173.325 - Acidified sodium chlorite solutions.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Acidified sodium chlorite solutions. 173.325... HUMAN CONSUMPTION Specific Usage Additives § 173.325 Acidified sodium chlorite solutions. Acidified sodium chlorite solutions may be safely used in accordance with the following prescribed conditions:...

  19. 21 CFR 173.325 - Acidified sodium chlorite solutions.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Acidified sodium chlorite solutions. 173.325... HUMAN CONSUMPTION Specific Usage Additives § 173.325 Acidified sodium chlorite solutions. Acidified sodium chlorite solutions may be safely used in accordance with the following prescribed conditions:...

  20. 21 CFR 173.325 - Acidified sodium chlorite solutions.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Acidified sodium chlorite solutions. 173.325... § 173.325 Acidified sodium chlorite solutions. Acidified sodium chlorite solutions may be safely used in... solution of sodium chlorite (CAS Reg. No. 7758-19-2) with any generally recognized as safe (GRAS) acid....

  1. 21 CFR 131.162 - Acidified sour cream.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Acidified sour cream. 131.162 Section 131.162 Food... HUMAN CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.162 Acidified sour cream. (a) Description. Acidified sour cream results from the souring of pasteurized...

  2. Reagent use efficiency with removal of nitrogen from pig slurry via struvite: A study on magnesium oxide and related by-products.

    PubMed

    Romero-Güiza, M S; Tait, S; Astals, S; Del Valle-Zermeño, R; Martínez, M; Mata-Alvarez, J; Chimenos, J M

    2015-11-01

    Controlled struvite formation has been attracting increasing attention as a near mature technology to recover nutrients from wastewater. However, struvite feasibility is generally limited by the high cost of chemical reagents. With the aim to understand and control reagent use efficiency, experiments and equilibrium model simulations examined inorganic nitrogen (TAN) removal from pig manure via struvite with added magnesium and phosphate reagents. Four industrial magnesium oxide (MgO), a commercial product and three by-products from magnesite calcination, were tested with phosphate added as a highly soluble potassium salt. TAN removal extents with the MgOs ranged from 47 to 72%, with the highest grade MgO providing the greatest extent of TAN removal. However, model analysis showed that all the MgO reagents were poorly soluble (only about 40% of added magnesium actually dissolved). The model results suggested that this poor dissolution was due to kinetic limitations, not solubility constraints. A further set of additional reagents (termed stabilization agents) were prepared by pre-treating the MgO reagents with phosphoric acid, and were tested separately as a source of both magnesium and phosphate. Results showed that acid pre-treatment of moderate to highly reactive MgOs (soft to medium-burnt) primarily formed bobierrite as the stabilizing agent, whereas the pre-treatment of very low reactivity MgOs (dead-burnt) mostly formed newberyite. The newberyite stabilizing agents achieved very high TAN removal extents of about 80%, which is significant, considering that these were formed from dead-burnt/low-grade MgOs. However, the bobierrite stabilizing agents achieved a substantially lower TAN removal extent than their medium-to-high reactivity precursor MgOs. Again, model analysis showed that the bobierrite stabilizing agents were poorly soluble, due to kinetic limitations, not solubility constraints. In contrast, the model suggested that the newberyite stabilizing

  3. Sizing pumps for slurries

    SciTech Connect

    Akhtar, S.Z.

    1996-11-01

    Slurry characteristics have a significant impact on centrifugal pump performance. For instance, as particle size increases or the percent solids concentration increases, pump head and efficiency decrease. Therefore, before a slurry pump is selected, it is important to define the slurry characteristics as accurately as possible. The effect of the slurry characteristics on the head and efficiency of the centrifugal pump will be emphasized (the effect on flowrate is less significant). The effect of slurry characteristics is more predominant in smaller pumps (with smaller diameter impellers) than in larger pumps. The data and relationship between the various slurry parameters have been developed from correlations and nomographs published by pump vendors from their field data and test results. The information helps to avoid specifying an undersized pump/motor assembly for slurry service.

  4. Ultrasound Analysis of Slurries

    DOEpatents

    Soong, Yee and Blackwell, Arthur G.

    2005-11-01

    An autoclave reactor allows for the ultrasonic analysis of slurry concentration and particle size distribution at elevated temperatures and pressures while maintaining the temperature- and pressure-sensitive ultrasonic transducers under ambient conditions. The reactor vessel is a hollow stainless steel cylinder containing the slurry which includes a stirrer and a N, gas source for directing gas bubbles through the slurry. Input and output transducers are connected to opposed lateral portions of the hollow cylinder for respectively directing sound waves through the slurry and receiving these sound waves after transmission through the slurry, where changes in sound wave velocity and amplitude can be used to measure slurry parameters. Ultrasonic adapters connect the transducers to the reactor vessel in a sealed manner and isolate the transducers from the hostile conditions within the vessel without ultrasonic signal distortion or losses.

  5. Ultrasound Analysis Of Slurries

    DOEpatents

    Soong, Yee; Blackwell, Arthur G.

    2005-11-01

    An autoclave reactor allows for the ultrasonic analysis of slurry concentration and particle size distribution at elevated temperatures and pressures while maintaining the temperature- and pressure-sensitive ultrasonic transducers under ambient conditions. The reactor vessel is a hollow stainless steel cylinder containing the slurry which includes a stirrer and a N.sub.2 gas source for directing gas bubbles through the slurry. Input and output transducers are connected to opposed lateral portions of the hollow cylinder for respectively directing sound waves through the slurry and receiving these sound waves after transmission through the slurry, where changes in sound wave velocity and amplitude can be used to measure slurry parameters. Ultrasonic adapters connect the transducers to the reactor vessel in a sealed manner and isolate the transducers from the hostile conditions within the vessel without ultrasonic signal distortion or losses.

  6. Mn2O3 Slurry Achieving Reduction of Slurry Waste

    NASA Astrophysics Data System (ADS)

    Kishii, Sadahiro; Nakamura, Ko; Hanawa, Kenzo; Watanabe, Satoru; Arimoto, Yoshihiro; Kurokawa, Syuhei; Doi, Toshiro K.

    2012-04-01

    Fumed silica is widely used for SiO2 chemical mechanical polishing (CMP). In semiconductor processes, only fresh slurry is used, the used slurry being disposed of. We have demonstrated that Mn2O3 abrasive slurry polishes dielectric SiO2 film, giving 4 times the removal rate of conventional fumed silica slurry. The higher removal rate reduces the total amount of slurry used, consequently reducing the amount of used slurry waste. The removal rate of Mn2O3 slurry remains constant for solid concentrations between l and 10 wt %, and stays constant without pad conditioning. These characteristics are very useful for slurry reuse. Remanufacture of Mn2O3 slurry from used slurry has been demonstrated, and the removal rates of the remanufactured and fresh slurries are the same. Reuse and remanufacturing drastically reduce the amount of waste.

  7. ICE SLURRY APPLICATIONS

    PubMed Central

    Kauffeld, M.; WANG, M. J.; Goldstein, V.; Kasza, K. E.

    2011-01-01

    The role of secondary refrigerants is expected to grow as the focus on the reduction of greenhouse gas emissions increases. The effectiveness of secondary refrigerants can be improved when phase changing media are introduced in place of single phase media. Operating at temperatures below the freezing point of water, ice slurry facilitates several efficiency improvements such as reductions in pumping energy consumption as well as lowering the required temperature difference in heat exchangers due to the beneficial thermo-physical properties of ice slurry. Research has shown that ice slurry can be engineered to have ideal ice particle characteristics so that it can be easily stored in tanks without agglomeration and then be extractable for pumping at very high ice fraction without plugging. In addition ice slurry can be used in many direct contact food and medical protective cooling applications. This paper provides an overview of the latest developments in ice slurry technology. PMID:21528014

  8. B-complex vitamins in cultured and acidified yogurt.

    PubMed

    Reddy, K P; Shahani, K M; Kulkarni, S M

    1976-02-01

    Studies were to determine the effect of various factors upon B-vitamin content of cultured yogurt and to compare the B-vitamin contents of cultured and direct acidified yogurt. Incubation of yogurt culture at 42 C for 3 h yielded maximum vitamin synthesis concurrent with optimal flavor and texture qualities. A method was standardized for the manufacture of direct acidified yogurt involving the use of Stabilac acidulant and nonfat dry milk, Carboxymethyl cellulose, gelatin, and Starite. Acidified yogurt showed a slightly higher content of certain B-vitamins than the cultured yogurt due to the contribution made by various food additives. Both cultured and acidified yogurt showed good keeping quality and freedom from microbial contaminants during storage at 5 C for 16 days. However, folic acid and vitamin B12 contents decreased 29 and 60% in cultured yogurt and 48 and 54% in acidified yogurt.

  9. Pressurized Vessel Slurry Pumping

    SciTech Connect

    Pound, C.R.

    2001-09-17

    This report summarizes testing of an alternate ''pressurized vessel slurry pumping'' apparatus. The principle is similar to rural domestic water systems and ''acid eggs'' used in chemical laboratories in that material is extruded by displacement with compressed air.

  10. Zeolite Combined with Alum and Polyaluminum Chloride Mixed with Agricultural Slurries Reduces Carbon Losses in Runoff from Grassed Soil Boxes.

    PubMed

    Murnane, J G; Brennan, R B; Fenton, O; Healy, M G

    2016-11-01

    Carbon (C) losses from agricultural soils to surface waters can migrate through water treatment plants and result in the formation of disinfection by-products, which are potentially harmful to human health. This study aimed to quantify total organic carbon (TOC) and total inorganic C losses in runoff after application of dairy slurry, pig slurry, or milk house wash water (MWW) to land and to mitigate these losses through coamendment of the slurries with zeolite (2.36-3.35 mm clinoptilolite) and liquid polyaluminum chloride (PAC) (10% AlO) for dairy and pig slurries or liquid aluminum sulfate (alum) (8% AlO) for MWW. Four treatments under repeated 30-min simulated rainfall events (9.6 mm h) were examined in a laboratory study using grassed soil runoff boxes (0.225 m wide, 1 m long; 10% slope): control soil, unamended slurries, PAC-amended dairy and pig slurries (13.3 and 11.7 kg t, respectively), alum-amended MWW (3.2 kg t), combined zeolite and PAC-amended dairy (160 and 13.3 kg t zeolite and PAC, respectively) and pig slurries (158 and 11.7 kg t zeolite and PAC, respectively), and combined zeolite and alum-amended MWW (72 and 3.2 kg t zeolite and alum, respectively). The unamended and amended slurries were applied at net rates of 31, 34, and 50 t ha for pig and dairy slurries and MWW, respectively. Significant reductions of TOC in runoff compared with unamended slurries were measured for PAC-amended dairy and pig slurries (52 and 56%, respectively) but not for alum-amended MWW. Dual zeolite and alum-amended MWW significantly reduced TOC in runoff compared with alum amendment only. We conclude that use of PAC-amended dairy and pig slurries and dual zeolite and alum-amended MWW, although effective, may not be economically viable to reduce TOC losses from organic slurries given the relatively low amounts of TOC measured in runoff from unamended slurries compared with the amounts applied.

  11. Impact of slurry management strategies on potential leaching of nutrients and pathogens in a sandy soil amended with cattle slurry.

    PubMed

    Fangueiro, D; Surgy, S; Napier, V; Menaia, J; Vasconcelos, E; Coutinho, J

    2014-12-15

    For farmers, management of cattle slurry (CS) is now a priority, in order to improve the fertilizer value of the slurry and simultaneously minimize its environmental impact. Several slurry pre-treatments and soil application methods to minimize ammonia emissions are now available to farmers, but the impact of such management strategies on groundwater is still unclear. A laboratory experiment was performed over 24 days in controlled conditions, with undisturbed soil columns (sandy soil) in PVC pipes (30 cm high and 5.7 cm in diameter). The treatments considered (4 replicates) were: a control with no amendment (CTR), injection of whole CS (WSI), and surface application of: whole CS (WSS), acidified (pH 5.5) whole CS (AWSS), the liquid fraction obtained by centrifugation of CS (LFS), and acidified (pH 5.5) liquid fraction (ALFS). An amount of CS equivalent to 240 kg N ha(-1) was applied in all treatments. The first leaching event was performed 72 h after application of the treatments and then leaching events were performed weekly to give a total of four irrigation events (IEs). All the leachates obtained were analyzed for mineral and organic nitrogen, electrical conductivity (EC), pH, total carbon, and phosphorus. Total coliforms and Escherichia coli were also quantified in the leachates obtained in the first IE. The results show that both acidification and separation had significant effects on the composition of the leachates: higher NO3(-) concentrations were observed for the LFS and ALFS relative to all the other treatments, throughout the experiment, and lower NO3(-) concentrations were observed for acidified relative to non-acidified treatments at IE2. Acidification of both the LF and WS led to higher NH4(+) concentrations as well as an increase of EC for treatment ALFS relative to the control, in the first IE, and lower pH values in the AWSS. Furthermore, the E. coli and total coliform concentrations in AWSS, LFS, and ALFS were significantly higher than in

  12. Schwertmannite stability in acidified coastal environments

    NASA Astrophysics Data System (ADS)

    Collins, Richard N.; Jones, Adele M.; Waite, T. David

    2010-01-01

    A combination of analytical and field measurements has been used to probe the speciation and cycling of iron in coastal lowland acid sulfate soils. Iron K-edge EXAFS spectroscopy demonstrated that schwertmannite dominated (43-77%) secondary iron mineralization throughout the oxidized and acidified soil profile, while pyrite and illite were the major iron-bearing minerals in the reduced potential acid sulfate soil layers. Analyses of contemporary precipitates from shallow acid sulfate soil groundwaters indicated that 2-line ferrihydrite, in addition to schwertmannite, is presently controlling secondary Fe(III) mineralization. Although aqueous pH values and concentrations of Fe(II) were seasonally high, no evidence was obtained for the Fe(II)-catalyzed crystallization of either mineral to goethite. The results of this study indicate that: (a) schwertmannite is likely to persist in coastal lowland acid sulfate soils on a much longer time-scale than predicted by laboratory experiments; (b) this mineral is less reactive in these types of soils due to surface-site coverage by components such as silicate and possibly, to a lesser extent, natural organic matter and phosphate and; (c) active water table management to promote oxic/anoxic cycles around the Fe(II)-Fe(III) redox couple, or reflooding of these soils, will be ineffective in promoting the Fe(II)-catalyzed transformation of either schwertmannite or 2-line ferrihydrite to crystalline iron oxyhydroxides.

  13. Slurry bubble column hydrodynamics

    NASA Astrophysics Data System (ADS)

    Rados, Novica

    Slurry bubble column reactors are presently used for a wide range of reactions in both chemical and biochemical industry. The successful design and scale up of slurry bubble column reactors require a complete understanding of multiphase fluid dynamics, i.e. phase mixing, heat and mass transport characteristics. The primary objective of this thesis is to improve presently limited understanding of the gas-liquid-solid slurry bubble column hydrodynamics. The effect of superficial gas velocity (8 to 45 cm/s), pressure (0.1 to 1.0 MPa) and solids loading (20 and 35 wt.%) on the time-averaged solids velocity and turbulent parameter profiles has been studied using Computer Automated Radioactive Particle Tracking (CARPT). To accomplish this, CARPT technique has been significantly improved for the measurements in highly attenuating systems, such as high pressure, high solids loading stainless steel slurry bubble column. At a similar set of operational conditions time-averaged gas and solids holdup profiles have been evaluated using the developed Computed Tomography (CT)/Overall gas holdup procedure. This procedure is based on the combination of the CT scans and the overall gas holdup measurements. The procedure assumes constant solids loading in the radial direction and axially invariant cross-sectionally averaged gas holdup. The obtained experimental holdup, velocity and turbulent parameters data are correlated and compared with the existing low superficial gas velocities and atmospheric pressure CARPT/CT gas-liquid and gas-liquid-solid slurry data. The obtained solids axial velocity radial profiles are compared with the predictions of the one dimensional (1-D) liquid/slurry recirculation phenomenological model. The obtained solids loading axial profiles are compared with the predictions of the Sedimentation and Dispersion Model (SDM). The overall gas holdup values, gas holdup radial profiles, solids loading axial profiles, solids axial velocity radial profiles and solids

  14. 75 FR 59268 - Draft Guidance for Industry: Acidified Foods; Availability

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-27

    ... and in employing appropriate quality control procedures. Under the draft guidance, processors of non... safe manufacturing, processing, and packing processes and in employing appropriate quality control... Establishment-Specific Written Quality Control Plans and Recordkeeping for Acidified Foods, and...

  15. New slurry pumps in China

    SciTech Connect

    Li, Z.; Wang, W.; Shi, Z.

    1998-07-01

    Wet parts of centrifugal slurry pumps are naturally subjected to wear, but local wear in pumps could be avoided, at least partly. Through studying the wear phenomenon of slurry pumps in industrial applications, a series of much more advanced slurry pumps was developed in China. Laboratory tests and industrial applications show that the new pumps are high in efficiency when transporting slurries, and uniform wear can be expected from them.

  16. New slurry pumps in China

    SciTech Connect

    Zhengwang Li; Wenlie Wang; Zhongyin Shi

    1998-04-01

    Wet parts of centrifugal slurry pumps are naturally subjected to wear, but local wear in pumps could be avoided, at least partly. Through studying the wear phenomenon of slurry pumps in industrial applications, a series of much more advanced slurry pumps was developed in China. Laboratory tests and industrial applications show that the new pumps are high in efficiency when transporting slurries, and uniform wear can be expected from them.

  17. Slurry reactor design studies

    SciTech Connect

    Fox, J.M.; Degen, B.D.; Cady, G.; Deslate, F.D.; Summers, R.L. ); Akgerman, A. ); Smith, J.M. )

    1990-06-01

    The objective of these studies was to perform a realistic evaluation of the relative costs of tublar-fixed-bed and slurry reactors for methanol, mixed alcohols and Fischer-Tropsch syntheses under conditions where they would realistically be expected to operate. The slurry Fischer-Tropsch reactor was, therefore, operated at low H{sub 2}/CO ratio on gas directly from a Shell gasifier. The fixed-bed reactor was operated on 2.0 H{sub 2}/CO ratio gas after adjustment by shift and CO{sub 2} removal. Every attempt was made to give each reactor the benefit of its optimum design condition and correlations were developed to extend the models beyond the range of the experimental pilot plant data. For the methanol design, comparisons were made for a recycle plant with high methanol yield, this being the standard design condition. It is recognized that this is not necessarily the optimum application for the slurry reactor, which is being proposed for a once-through operation, coproducing methanol and power. Consideration is also given to the applicability of the slurry reactor to mixed alcohols, based on conditions provided by Lurgi for an Octamix{trademark} plant using their standard tubular-fixed reactor technology. 7 figs., 26 tabs.

  18. Ammonia emission after slurry application to grassland in Switzerland

    NASA Astrophysics Data System (ADS)

    Häni, Christoph; Sintermann, Jörg; Kupper, Thomas; Jocher, Markus; Neftel, Albrecht

    2016-01-01

    Loss of ammonia (NH3) after field application of livestock slurry contributes between 30% and 50% of agricultural NH3 emissions from European countries. The objectives of this study were to re-evaluate NH3 emissions following application of cattle and pig slurry to grassland in Switzerland and to investigate the effectiveness of abatement techniques. In 17 field experiments, NH3 emissions were determined with a micrometeorological approach, relating the emission to the measured concentration by means of atmospheric dispersion modelling. The cattle slurry applied exhibited an average dry matter content of 3.3% (range between 1.0% and 6.7% dry matter). The emission after application of cattle slurry spread with a splash plate (referred to as reference technique) ranged from 10% to 47% of applied Total Ammoniacal Nitrogen (% of TAN) and averaged to 25% of TAN. This range of losses is lower by approx. a factor of two compared to measurements from earlier Swiss experiments. Applications with trailing hose and trailing shoe systems yielded an average reduction of 51% and 53%, respectively, relative to the reference technique. A regression analysis showed that the dry matter content of the slurry and the air temperature are important drivers for NH3 emission.

  19. Growth and blood chemistry of ducklings reared on acidified wetlands

    USGS Publications Warehouse

    Rattner, B.A.; Haramis, G.; Linder, G.; Chu, D.

    1985-01-01

    Acid deposition is one factor that may be responsible for the decline of some waterfowl populations. Growth and physiological condition were monitored in captive-reared black ducks (Anas rubripes) exposed for 10-day trials (day 11-20 of life) on control (pH 6.8) and acidified (pH 5.0) man-made emergent wetlands. Impaired growth (body weight, culmen and tarsus length) and increased mortality (50%) were apparent in broods (hen + 4 ducklings) reared on acidified wetIands. Ducklings exbibiting poor growth had reduced hematocrit, plasma protein and cholesterol levels. This subset of birds had elevated plasma uric acid concentration and creatine kinase activity (perhaps due to enhanced protein and nucleotide catabolism). and elevated pIasma K+ levels. Based upon overt appearance, growth and blood chemistry, ducklings exposed to acidified wetlands were concluded to be in poorer condittion than those exposed on circumneutral pH wetlands.

  20. System and method for slurry handling

    DOEpatents

    Steele, Raymond Douglas; Oppenheim, Judith Pauline

    2015-12-29

    A system includes a slurry depressurizing system that includes a liquid expansion system configured to continuously receive a slurry at a first pressure and continuously discharge the slurry at a second pressure. For example, the slurry depressurizing system may include an expansion turbine to expand the slurry from the first pressure to the second pressure.

  1. INEZ, KENTUCKY COAL SLURRY SPILL

    EPA Science Inventory

    On October 11th, 2000, a breach of a coal slurry impoundment released approximately 210 million gallons of coal slurry ( a mixture of fine coal particles, silt, clay, sand and water) into the Big Andy Branch, Wolf Creek, and Coldwater Fork. Approximately 75 river miles were affec...

  2. Rheometry of natural sediment slurries

    USGS Publications Warehouse

    Major, Jon J.; ,

    1993-01-01

    Recent experimental analyses of natural sediment slurries yield diverse results yet exhibit broad commonality of rheological responses under a range of conditions and shear rates. Results show that the relation between shear stress and shear rate is primarily nonlinear, that the relation can display marked hysteresis, that minimum shear stress can occur following yield, that physical properties of slurries are extremely sensitive to sediment concentration, and the concept of slurry yield strength is still debated. New rheometric analyses have probed viscoelastic behavior of sediment slurries. Results show that slurries composed of particles ??? 125 ?? m exhibit viscoelastic responses, and that shear stresses are relaxed over a range of time scales rather than by a single response time.

  3. DEHYDRATION OF DEUTERIUM OXIDE SLURRIES

    DOEpatents

    Hiskey, C.F.

    1959-03-10

    A method is presented for recovering heavy water from uranium oxide-- heavy water slurries. The method consists in saturating such slurries with a potassium nitrate-sodium nitrate salt mixture and then allowing the self-heat of the slurry to raise its temperature to a point slightly in excess of 100 deg C, thus effecting complete evaporation of the free heavy water from the slurry. The temperature of the slurry is then allowed to reach 300 to 900 deg C causing fusion of the salt mixture and expulsion of the water of hydration. The uranium may be recovered from the fused salt mixture by treatment with water to leach the soluble salts away from the uranium-containing residue.

  4. Thermophilic treatment of acidified and partially acidified wastewater using an anaerobic submerged MBR: Factors affecting long-term operational flux.

    PubMed

    Jeison, D; van Lier, J B

    2007-09-01

    The long-term operation of two thermophilic anaerobic submerged membrane bioreactors (AnSMBRs) was studied using acidified and partially acidified synthetic wastewaters. In both reactors, cake formation was identified as the key factor governing critical flux. Even though cake formation was observed to be mostly reversible, particle deposition proceeds fast once the critical flux is exceeded. Very little irreversible fouling was observed during long-term operation, irrespective of the substrate. Critical flux values at the end of the reactors operation were 7 and 3L/m(2)h for the AnSMBRs fed with acidified and partially acidified wastewaters, respectively, at a gas superficial velocity of 70m/h. Small particle size was identified as the responsible parameter for the low observed critical flux values. The degree of wastewater acidification significantly affected the physical properties of the sludge, determining the attainable flux. Based on the fluxes observed in this research, the membrane costs would be in the range of 0.5euro/m(3) of treated wastewater. Gas sparging was ineffective in increasing the critical flux values. However, preliminary tests showed that cross-flow operation may be a feasible alternative to reduce particle deposition.

  5. Characterization of odor released during handling of swine slurry: Part II. Effect of production type, storage and physicochemical characteristics of the slurry

    NASA Astrophysics Data System (ADS)

    Blanes-Vidal, V.; Hansen, M. N.; Adamsen, A. P. S.; Feilberg, A.; Petersen, S. O.; Jensen, B. B.

    The quality of rural life can be affected by offensive odors released from animal buildings and storage units. The objectives of this study were to compare the concentrations of odor and odorants above different types of stirred swine slurry to analyze the relationships between concentrations of odor (and odorants) and physicochemical characteristics of the slurry (i.e. pH, temperature, dry matter, volatile solids, and concentration of 22 chemical compounds); and to propose predictive models for the odor concentration (OC) based on these physicochemical characteristics (solely and in combination with concentrations of specific odorants in the air above the slurries). The study comprised data on concentrations of odor and odorants in the air above slurry samples (fresh and/or stored) collected from production units with farrowing sows, finishing swines, or weaning pigs at eight swine operations ( N = 48). OC measured in the air above stirred swine slurry samples were not significantly different among production types or storage times. The physicochemical characteristics of the slurries were not useful for predicting OC or concentrations of hydrogen sulfide (or organic sulfides) above the slurry, but were related to concentrations of other emitted gases such as phenols and indoles ( r2 = 0.65-0.79, p <0.05), ammonia ( r2 = 0.86, p < 0.05) and carboxylic acids ( r2 = 0.23-0.59, p <0.05). There was good precision of predictive models of OC based on selected slurry characteristics (i.e. pH, dry matter, nitrogen content, sulfur content or concentrations of individual aromatic compounds and carboxylic acids) together with concentrations of specific odorants in the air (e.g. hydrogen sulfide) ( r2 between 0.70 and 0.92). This study suggests that predictive models could be useful for evaluating odor nuisance potentials of swine slurry during handling.

  6. Coal slurry pipelining

    SciTech Connect

    Chassagne, P.J.

    1980-02-05

    A method is disclosed for preparing industrial ores, e.g., coal, for pipelining and pipelining the ores to a site for subsequent processing or use. Ore from a mine is screened into two fractions, one having a large size particle distribution and one having a small size particle distribution, each fraction retaining both the ore and the refuse. The large size particle fraction is cleaned of refuse and the clean ore therefrom crushed to a size distribution of the smaller size or small size ore fraction. The separated refuse from the large size particle fraction is ground to provide superfines to the extent required for the proper particle size distribution for pipelining. The ore and superfine refuse are combined in a water slurry for pipelining. After pipelining the ore, the ore is cleaned and dewatered conveniently as known in the art for fine ore. The resulting ore may then be stockpiled or directly used.

  7. Manifold Coal-Slurry Transport System

    NASA Technical Reports Server (NTRS)

    Liddle, S. G.; Estus, J. M.; Lavin, M. L.

    1986-01-01

    Feeding several slurry pipes into main pipeline reduces congestion in coal mines. System based on manifold concept: feeder pipelines from each working entry joined to main pipeline that carries coal slurry out of panel and onto surface. Manifold concept makes coal-slurry haulage much simpler than existing slurry systems.

  8. NACA Research on Slurry Fuels

    NASA Technical Reports Server (NTRS)

    Pinns, M L; Olson, W T; Barnett, H C; Breitwieser, R

    1958-01-01

    An extensive program was conducted to investigate the use of concentrated slurries of boron and magnesium in liquid hydrocarbon as fuels for afterburners and ramjet engines. Analytical calculations indicated that magnesium fuel would give greater thrust and that boron fuel would give greater range than are obtainable from jet hydrocarbon fuel alone. It was hoped that the use of these solid elements in slurry form would permit the improvement to be obtained without requiring unconventional fuel systems or combustors. Small ramjet vehicles fueled with magnesium slurry were flown successfully, but the test flights indicated that further improvement of combustors and fuel systems was needed.

  9. Tribological Properties Of Coal Slurries

    NASA Technical Reports Server (NTRS)

    Fusaro, Robert L.; Schrubens, Dale L.

    1988-01-01

    Report describes study of tribological properties of coal/methanol slurries with pin-on-disk tribometer. Coefficients of friction, rates of wear of steel pin, and morphological studies of worn surfaces conducted on pins and disks of AISI 440C HT stainless steel and M-50 tool steel, both used as bearing steels. Coal slurries considered as replacement fuels in terrestrial oil-burning facilities and possible fuels for future aircraft turbine engines. Rates of wear of metallic components through which slurries flow limit such practical applications.

  10. Streamline coal slurry letdown valve

    DOEpatents

    Platt, Robert J.; Shadbolt, Edward A.

    1983-01-01

    A streamlined coal slurry letdown valve is featured which has a two-piece throat comprised of a seat and seat retainer. The two-piece design allows for easy assembly and disassembly of the valve. A novel cage holds the two-piece throat together during the high pressure letdown. The coal slurry letdown valve has long operating life as a result of its streamlined and erosion-resistance surfaces.

  11. Streamline coal slurry letdown valve

    DOEpatents

    Platt, R.J.; Shadbolt, E.A.

    1983-11-08

    A streamlined coal slurry letdown valve is featured which has a two-piece throat comprised of a seat and seat retainer. The two-piece design allows for easy assembly and disassembly of the valve. A novel cage holds the two-piece throat together during the high pressure letdown. The coal slurry letdown valve has long operating life as a result of its streamlined and erosion-resistance surfaces. 5 figs.

  12. Medical ice slurry production device

    DOEpatents

    Kasza, Kenneth E.; Oras, John; Son, HyunJin

    2008-06-24

    The present invention relates to an apparatus for producing sterile ice slurries for medical cooling applications. The apparatus is capable of producing highly loaded slurries suitable for delivery to targeted internal organs of a patient, such as the brain, heart, lungs, stomach, kidneys, pancreas, and others, through medical size diameter tubing. The ice slurry production apparatus includes a slurry production reservoir adapted to contain a volume of a saline solution. A flexible membrane crystallization surface is provided within the slurry production reservoir. The crystallization surface is chilled to a temperature below a freezing point of the saline solution within the reservoir such that ice particles form on the crystallization surface. A deflector in the form of a reciprocating member is provided for periodically distorting the crystallization surface and dislodging the ice particles which form on the crystallization surface. Using reservoir mixing the slurry is conditioned for easy pumping directly out of the production reservoir via medical tubing or delivery through other means such as squeeze bottles, squeeze bags, hypodermic syringes, manual hand delivery, and the like.

  13. Comparative testing of slurry monitors

    SciTech Connect

    Hylton, T.D.; Bayne, C.K.; Anderson, M.S.; Van Essen, D.C.

    1998-05-01

    The US Department of Energy (DOE) has millions of gallons of radioactive liquid and sludge wastes that must be retrieved from underground storage tanks, transferred to treatment facilities, and processed to a final waste form. The wastes will be removed from the current storage tanks by mobilizing the sludge wastes and mixing them with the liquid wastes to create slurries. Each slurry would then be transferred by pipeline to the desired destination. To reduce the risk of plugging a pipeline, the transport properties (e.g., density, suspended solids concentration, viscosity, particle size range) of the slurry should be determined to be within acceptable limits prior to transfer. These properties should also be monitored and controlled within specified limits while the slurry transfer is in progress. The DOE issued a call for proposals for developing on-line instrumentation to measure the transport properties of slurries. In response to the call for proposals, several researchers submitted proposals and were funded to develop slurry monitoring instruments. These newly developed DOE instruments are currently in the prototype stage. Before the instruments were installed in a radioactive application, the DOE wanted to evaluate them under nonradioactive conditions to determine if they were accurate, reliable, and dependable. The goal of this project was to test the performance of the newly developed DOE instruments along with several commercially available instruments. The baseline method for comparison utilized the results from grab-sample analyses.

  14. Coal slurry fuel supply and purge system

    DOEpatents

    McDowell, Robert E.; Basic, Steven L.; Smith, Russel M.

    1994-01-01

    A coal slurry fuel supply and purge system for a locomotive engines is disclosed which includes a slurry recirculation path, a stand-by path for circulating slurry during idle or states of the engine when slurry fuel in not required by the engine, and an engine header fluid path connected to the stand-by path, for supplying and purging slurry fuel to and from fuel injectors. A controller controls the actuation of valves to facilitate supply and purge of slurry to and from the fuel injectors. A method for supplying and purging coal slurry in a compression ignition engine is disclosed which includes controlling fluid flow devices and valves in a plurality of fluid paths to facilitate continuous slurry recirculation and supply and purge of or slurry based on the operating state of the engine.

  15. The occurrence of intestinal parasites in swine slurry and their removal in activated sludge plants.

    PubMed

    Reinoso, Roberto; Becares, Eloy

    2008-09-01

    Thirteen intensive pig farms and two activated sludge treatment plants for pig slurry in north-western Spain were studied from April 2005 to June 2006 in order to evaluate the presence of enteric pathogens (Cryptosporidium, Giardia and helminths) and the efficiency with which they were removed. These parasites were present on 53%, 7% and 38% of the farms studied, respectively, with concentrations of 10(4)-10(5) oocysts per litre (/L) for Cryptosporidium, 10(3)cysts/L for Giardia and 10(2)-10(3) eggs/L for helminths. The overall removal of parasites in the pig slurry treatment plants ranged from 86.7% to over 99.99%. The results revealed a constant reduction at each stage of the treatment system, with activated sludge processes being the most effective treatment in reducing pathogens in pig slurry, 78-81% for Cryptosporidium oocysts and over 99.9% for helminth eggs. A heat drying procedure for sludge removed 4.3 log units of Cryptosporidium oocysts, demonstrating the excellent effectiveness of this treatment for reducing pathogens in sludge intended to be applied to land.

  16. Development of biodiesel slurry fuels

    SciTech Connect

    Suppes, G.J.; Ng, C.; Srinivasan, B.

    1994-12-31

    As an alternative to diesel, the DOE has recently supported research which developed coal-water-slurries to the extent that they have demonstrated in low-, medium-, and high-speed diesel engines. Coal-water-slurry (CWS) fuels would be an American-made alternative to diesel distilled from imported crude oil. Such alternatives to imported oil are particularly desirable as 1994 crude oil imports will most likely exceed those disastrously high levels of the early 1980`s which led to a major recession. This paper is on the testing and development of biodiesel slurry fuels (e.g. corn flour and water) as an alternative to diesel for use in a modified diesel engine. While the economics for CWS`s are not favorable until bulk, tax-free diesel prices exceed $0.80 per gallon, a preliminary analysis of biodiesel slurries shows economic viability at today`s diesel prices. This paper presents advantages of biodiesel slurries over CWS`s due to different ash compositions and economics specific to applications on farm tractors. Engine modifications, fuel costs, fuel processing, fuel performance, and on-going research are discussed.

  17. Coal-oil slurry preparation

    DOEpatents

    Tao, John C.

    1983-01-01

    A pumpable slurry of pulverized coal in a coal-derived hydrocarbon oil carrier which slurry is useful as a low-ash, low-sulfur clean fuel, is produced from a high sulfur-containing coal. The initial pulverized coal is separated by gravity differentiation into (1) a high density refuse fraction containing the major portion of non-coal mineral products and sulfur, (2) a lowest density fraction of low sulfur content and (3) a middlings fraction of intermediate sulfur and ash content. The refuse fraction (1) is gasified by partial combustion producing a crude gas product from which a hydrogen stream is separated for use in hydrogenative liquefaction of the middlings fraction (3). The lowest density fraction (2) is mixed with the liquefied coal product to provide the desired fuel slurry. Preferably there is also separately recovered from the coal liquefaction LPG and pipeline gas.

  18. YIELD STRESS REDUCTION OF DWPF MELTER FEED SLURRIES

    SciTech Connect

    Stone, M; Michael02 Smith, M

    2006-12-28

    The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides (primarily iron, aluminum, magnesium, manganese, and uranium) and soluble sodium salts (carbonate, hydroxide, nitrite, nitrate, sulfate). The pretreatment process acidifies the sludge with nitric and formic acids, adds the glass formers as glass frit, then concentrates the resulting slurry to approximately 50 weight percent (wt%) total solids. This slurry is fed to the joule-heated melter where the remaining water is evaporated followed by calcination of the solids and conversion to glass. The Savannah River National Laboratory (SRNL) is currently assisting DWPF efforts to increase throughput of the melter. As part of this effort, SRNL has investigated methods to increase the solids content of the melter feed to reduce the heat load required to complete the evaporation of water and allow more of the energy available to calcine and vitrify the waste. The process equipment in the facility is fixed and cannot process materials with high yield stresses, therefore increasing the solids content will require that the yield stress of the melter feed slurries be reduced. Changing the glass former added during pretreatment from an irregularly shaped glass frit to nearly spherical beads was evaluated. The evaluation required a systems approach which included evaluations of the effectiveness of beads in reducing the melter feed yield stress as well as evaluations of the processing impacts of changing the frit morphology. Processing impacts of beads include changing the settling rate of the glass former (which effects mixing and sampling of the melter feed slurry and the frit addition equipment) as well as impacts on the melt behavior due to decreased surface area of the beads versus frit

  19. Effects of acidifying reagents on microwave treatment of dairy manure.

    PubMed

    Srinivasan, Asha; Nkansah-Boadu, Frank; Liao, Ping H; Lo, Kwang V

    2014-01-01

    Dairy manure, acidified using organic acids (acetic, oxalic, and citric acid) were treated with microwave enhanced advanced oxidation process (MW/H2O2-AOP). The effect of a mixture of oxalic acid and commonly used mineral acids (sulfuric and hydrochloric acid) on MW/H2O2-AOP was also examined. Substantial amounts of phosphorus were released under MW/H2O2-AOP, regardless of organic acid or mineral acid used. All three organic acids were good acidifying reagents; however, only oxalic acid could remove free calcium ion in the solution, and improve settleability of dairy manure. The MW/H2O2-AOP and calcium removal process could be combined into a single-stage process, which could release phosphate, solubilize solids and remove calcium from dairy manure at the same time. A mixture of oxalic acid and mineral acid produced the maximum volume of clear supernatant and had an ideal molar ratio of calcium to magnesium for effective struvite (magnesium ammonium phosphate) crystallization process. A single-stage MW/H2O2-AOP would simplify the process and reduce mineral acid consumption compared to a two-stage operation. The results of a pilot scale study demonstrate that MW/H2O2-AOP is effective in treating manure and recovering resource from dairy farms.

  20. Supersonic coal water slurry fuel atomizer

    DOEpatents

    Becker, Frederick E.; Smolensky, Leo A.; Balsavich, John

    1991-01-01

    A supersonic coal water slurry atomizer utilizing supersonic gas velocities to atomize coal water slurry is provided wherein atomization occurs externally of the atomizer. The atomizer has a central tube defining a coal water slurry passageway surrounded by an annular sleeve defining an annular passageway for gas. A converging/diverging section is provided for accelerating gas in the annular passageway to supersonic velocities.

  1. Slurry pumping: Pump performance prediction

    SciTech Connect

    Taccani, R.; Pediroda, V.; Reini, M.; Giadrossi, A.

    2000-07-01

    Centrifugal pumps are being used increasingly for transportation of slurries through pipelines. To design a slurry handling system it is essential to have a knowledge of the effects of suspended solids on the pump performance. A new test loop has been realized in the laboratory of the Energetics Department of the University of Trieste which allows pump performance to be determined at various pump speeds, with many different mixture concentrations and rheologies. The pump test rig consists of 150 mm diameter pipe with facilities for measuring suction and discharge pressure, flowrate, pump input power and speed, slurry density and temperature. In particular flowrate is measured by diverting flow into a weighing tank and timing a specified volume of slurry. An automatic PC based data acquisition system has been implemented. Preliminary tests with clear water show that performance can be measured with good repeatability and accuracy. The new test rig is used to verify the range of validity of the correlations to predict pump performance, available in literature and of that proposed by authors. This correlation, based on a Neural Network and not on a predefined analytical expression, can be easily improved with new experimental data.

  2. Tribological properties of coal slurries

    NASA Technical Reports Server (NTRS)

    Fusaro, Robert L.; Schrubens, Dale L.

    1987-01-01

    A pin-on-disk tribometer was used to study the tribological properties of methyl alcohol-coal slurries. Friction coefficients, steel pin wear rates and wear surface morphological studies were conducted on AISI 440C HT and M-50 bearing steels which were slid dry and in solutions of methyl alcohol, methyl alcohol-fine coal particles, and methyl alcohol-fine coal particles-flocking additive. The latter was an oil derived from coal and originally intended to be added to the coal slurry to improve the sedimentation and rheology properties. The results of this study indicated that the addition of the flocking additive to the coal slurry markedly improved the tribological properties, especially wear. In addition, the type of steel was found to be very important in determining the type of wear that took place. Cracks and pits were found on the M-50 steel pin wear surfaces that slid in the coal slurries while 440C HT steel pins showed none.

  3. Odor characterization from barns and slurry treatment facilities at a commercial swine facility in South Korea

    NASA Astrophysics Data System (ADS)

    Jo, Sang-Hee; Kim, Ki-Hyun; Jeon, Byong-Hun; Lee, Min-Hee; Kim, Yong-Hyun; Kim, Bo-Won; Cho, Sung-Back; Hwang, Ok-Hwa; Bhattacharya, Satya Sundar

    2015-10-01

    In this study, emission characteristics of major odorants in pig confinement facilities were investigated through comparative analysis between odorant composition and odor intensity. Odorant samples in ambient air were collected from five different paired sampling sites: (1) in- and outside of windowless pig barn, (2) in- and outside of open pig barn, (3) before/after slurry treatment (via liquid fertilization), (4) before/after composting, and (5) two reference background sites on a pig confinement facility. A total of 47 compounds consisting of key offensive odorants (such as reduced sulfur and volatile organic compounds) were measured from each selected site. When the results are compared in terms of odor intensity, a list of odorants (sulfur compounds, volatile fatty acids, phenols, and indoles) were generally seen at enhanced levels on most sites. In two types of pig barn facilities (windowless ('W') and open ('O')), butyric and valeric acid were the predominant species. The removal efficiency of odorants was quite different between the two slurry treatment approaches of composting and liquid fertilization. Although the efficiencies of odor removal in the former were not sufficient, that of the latter was fairly significant in terms of odor intensity. However, some odorants like hydrogen sulfide, methanethiol, p-cresol, and butyric acid were still retained above the odor threshold level. Accordingly, odorant emissions from animal housing facilities can be characterized most effectively by key odorants such as volatile fatty acids and reduced sulfur species.

  4. Physiological ecology of Mougeotia (Zygnemataceae) from an experimentally acidified lake

    SciTech Connect

    Arancibia-Avila, P.E.

    1994-01-01

    Filamentous green algae were collected in July, 1989, from metaphytic blooms that occurred in the acidified (pH 5.2) basin, but not an unacidified reference basin (pH 6.1) of Little Rock Lake, Vilas Co., WI. Isolates of a Mougeotia species and Spirogyra reflexa were cultured at pH 5.5, with aeration. Measurements Of O[sub 2] production in a factorial experiment revealed optimal irradiance and temperature for photosynthesis in Mougeotia were 2500 [mu]E[center dot]m[sup [minus]2][center dot]s[sup [minus]l] and 25[degrees]C. Additional O[sub 2] evolution measurements showed that the optimal pH for Mougeotia photosynthesis was 8, but that net photosynthesis was positive from pH 8 to 3. Further studies indicated that Mougeotia was tolerant to concentrations of zinc and aluminum that were greater than levels observed in the acidified basin of the lake. Since inorganic carbon (C[sub i]) is known to limit Mougeotia photosynthesis and growth in acidified lakes, the occurrence of carbonic anhydrase (CA) as a mechanism for uptake and concentration of C[sub i] was investigated. No CA activity was detected in S. reflexa. In contrast, both external and internal CA were measured in Mougeotia at pH 3.7 and at pH 8. By comparison to pH 8, at pH 3.7 external CA activity increased by a factor of about 2. An antibody to Chlamydomonas external CA was used to localize CA in the plasma membrane and cell wall of both Chlamydomonas and Mougeotia. When unaerated (DIC-limited) Mougeotia was grown in SD11 medium supplemented with 1% glucose, chlorophyll a levels were significantly higher than for cultures grown without sugar. Chloroplast morphology was also judged superior for sugar-supplemented cultures. The data suggest that Mougeotia possesses a DIC-concentrating system, and may also be able to import DOC (glucose).

  5. Yield Stress Reduction of DWPF Melter Feed Slurries

    SciTech Connect

    Stone, M.E.; Smith, M.E.

    2007-07-01

    The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides and soluble sodium salts. The pretreatment process acidifies the sludge with nitric and formic acids, adds the glass formers as glass frit, then concentrates the resulting slurry to approximately 50 weight percent (wt%) total solids. This slurry is fed to the joule-heated melter where the remaining water is evaporated followed by calcination of the solids and conversion to glass. The Savannah River National Laboratory (SRNL) is currently assisting DWPF efforts to increase throughput of the melter. As part of this effort, SRNL has investigated methods to increase the solids content of the melter feed to reduce the heat load required to complete the evaporation of water and allow more of the energy available to calcine and vitrify the waste. The process equipment in the facility is fixed and cannot process materials with high yield stresses, therefore increasing the solids content will require that the yield stress of the melter feed slurries be reduced. Changing the glass former added during pretreatment from an irregularly shaped glass frit to nearly spherical beads was evaluated. The evaluation required a systems approach which included evaluations of the effectiveness of beads in reducing the melter feed yield stress as well as evaluations of the processing impacts of changing the frit morphology. Processing impacts of beads include changing the settling rate of the glass former (which effects mixing and sampling of the melter feed slurry and the frit addition equipment) as well as impacts on the melt behavior due to decreased surface area of the beads versus frit. Beads were produced from the DWPF process frit by fire polishing. The frit was allowed to free fall through a flame

  6. Improvement of heating uniformity in packaged acidified vegetables pasteurized with a 915 MHz continuous microwave system

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Continuous microwave processing to produce shelf-stable acidified vegetables with moderate to high salt contents poses challenges in pasteurization due to reduced microwave penetration depths and non-uniform heating. Cups of sweetpotato, red bell pepper, and broccoli acidified to pH 3.8 with citric...

  7. Growth potential of Clostridium perfringens from spores in acidified beef, pork and poultry products during chilling

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The ability of C. perfringens to germinate and grow in acidified ground beef as well as in ten commercially prepared acidified beef, pork and poultry products was assessed. The pH of ground beef was adjusted using organic vinegar to achieve various pH values between 5.0 and 5.6; the pH of the commer...

  8. Coral host cells acidify symbiotic algal microenvironment to promote photosynthesis.

    PubMed

    Barott, Katie L; Venn, Alexander A; Perez, Sidney O; Tambutté, Sylvie; Tresguerres, Martin

    2015-01-13

    Symbiotic dinoflagellate algae residing inside coral tissues supply the host with the majority of their energy requirements through the translocation of photosynthetically fixed carbon. The algae, in turn, rely on the host for the supply of inorganic carbon. Carbon must be concentrated as CO2 in order for photosynthesis to proceed, and here we show that the coral host plays an active role in this process. The host-derived symbiosome membrane surrounding the algae abundantly expresses vacuolar H(+)-ATPase (VHA), which acidifies the symbiosome space down to pH ∼ 4. Inhibition of VHA results in a significant decrease in average H(+) activity in the symbiosome of up to 75% and a significant reduction in O2 production rate, a measure of photosynthetic activity. These results suggest that host VHA is part of a previously unidentified carbon concentrating mechanism for algal photosynthesis and provide mechanistic evidence that coral host cells can actively modulate the physiology of their symbionts.

  9. Coral host cells acidify symbiotic algal microenvironment to promote photosynthesis

    PubMed Central

    Barott, Katie L.; Venn, Alexander A.; Perez, Sidney O.; Tambutté, Sylvie; Tresguerres, Martin

    2015-01-01

    Symbiotic dinoflagellate algae residing inside coral tissues supply the host with the majority of their energy requirements through the translocation of photosynthetically fixed carbon. The algae, in turn, rely on the host for the supply of inorganic carbon. Carbon must be concentrated as CO2 in order for photosynthesis to proceed, and here we show that the coral host plays an active role in this process. The host-derived symbiosome membrane surrounding the algae abundantly expresses vacuolar H+-ATPase (VHA), which acidifies the symbiosome space down to pH ∼4. Inhibition of VHA results in a significant decrease in average H+ activity in the symbiosome of up to 75% and a significant reduction in O2 production rate, a measure of photosynthetic activity. These results suggest that host VHA is part of a previously unidentified carbon concentrating mechanism for algal photosynthesis and provide mechanistic evidence that coral host cells can actively modulate the physiology of their symbionts. PMID:25548188

  10. Comparison of a Powdered, Acidified Liquid, and Non-Acidified Liquid Human Milk Fortifier on Clinical Outcomes in Premature Infants

    PubMed Central

    Thoene, Melissa; Lyden, Elizabeth; Weishaar, Kara; Elliott, Elizabeth; Wu, Ruomei; White, Katelyn; Timm, Hayley; Anderson-Berry, Ann

    2016-01-01

    We previously compared infant outcomes between a powdered human milk fortifier (P-HMF) vs. acidified liquid HMF (AL-HMF). A non-acidified liquid HMF (NAL-HMF) is now commercially available. The purpose of this study is to compare growth and outcomes of premature infants receiving P-HMF, AL-HMF or NAL-HMF. An Institutional Review Board (IRB) approved retrospective chart review compared infant outcomes (born < 2000 g) who received one of three HMF. Growth, enteral nutrition, laboratory and demographic data were compared. 120 infants were included (P-HMF = 46, AL-HMF = 23, NAL-HMF = 51). AL-HMF infants grew slower in g/day (median 23.66 vs. P-HMF 31.27, NAL-HMF 31.74 (p < 0.05)) and in g/kg/day, median 10.59 vs. 15.37, 14.03 (p < 0.0001). AL-HMF vs. NAL-HMF infants were smaller at 36 weeks gestational age (median 2046 vs. 2404 g, p < 0.05). However AL-HMF infants received more daily calories (p = 0.21) and protein (p < 0.0001), mean 129 cal/kg, 4.2 g protein/kg vs. P-HMF 117 cal/kg, 3.7 g protein/kg , NAL-HMF 120 cal/kg, 4.0 g protein/kg. AL-HMF infants exhibited lower carbon dioxide levels after day of life 14 and 30 (p < 0.0001, p = 0.0038). Three AL-HMF infants (13%) developed necrotizing enterocolitis (NEC) vs. no infants in the remaining groups (p = 0.0056). A NAL-HMF is the most optimal choice for premature human milk-fed infants in a high acuity neonatal intensive care unit (NICU). PMID:27472359

  11. Comparison of a Powdered, Acidified Liquid, and Non-Acidified Liquid Human Milk Fortifier on Clinical Outcomes in Premature Infants.

    PubMed

    Thoene, Melissa; Lyden, Elizabeth; Weishaar, Kara; Elliott, Elizabeth; Wu, Ruomei; White, Katelyn; Timm, Hayley; Anderson-Berry, Ann

    2016-07-26

    We previously compared infant outcomes between a powdered human milk fortifier (P-HMF) vs. acidified liquid HMF (AL-HMF). A non-acidified liquid HMF (NAL-HMF) is now commercially available. The purpose of this study is to compare growth and outcomes of premature infants receiving P-HMF, AL-HMF or NAL-HMF. An Institutional Review Board (IRB) approved retrospective chart review compared infant outcomes (born < 2000 g) who received one of three HMF. Growth, enteral nutrition, laboratory and demographic data were compared. 120 infants were included (P-HMF = 46, AL-HMF = 23, NAL-HMF = 51). AL-HMF infants grew slower in g/day (median 23.66 vs. P-HMF 31.27, NAL-HMF 31.74 (p < 0.05)) and in g/kg/day, median 10.59 vs. 15.37, 14.03 (p < 0.0001). AL-HMF vs. NAL-HMF infants were smaller at 36 weeks gestational age (median 2046 vs. 2404 g, p < 0.05). However AL-HMF infants received more daily calories (p = 0.21) and protein (p < 0.0001), mean 129 cal/kg, 4.2 g protein/kg vs. P-HMF 117 cal/kg, 3.7 g protein/kg , NAL-HMF 120 cal/kg, 4.0 g protein/kg. AL-HMF infants exhibited lower carbon dioxide levels after day of life 14 and 30 (p < 0.0001, p = 0.0038). Three AL-HMF infants (13%) developed necrotizing enterocolitis (NEC) vs. no infants in the remaining groups (p = 0.0056). A NAL-HMF is the most optimal choice for premature human milk-fed infants in a high acuity neonatal intensive care unit (NICU).

  12. Application of PTR-MS for measuring odorant emissions from soil application of manure slurry.

    PubMed

    Feilberg, Anders; Bildsoe, Pernille; Nyord, Tavs

    2015-01-09

    Odorous volatile organic compounds (VOC) and hydrogen sulfide (H2S) are emitted together with ammonia (NH3) from manure slurry applied as a fertilizer, but little is known about the composition and temporal variation of the emissions. In this work, a laboratory method based on dynamic flux chambers packed with soil has been used to measure emissions from untreated pig slurry and slurry treated by solid-liquid separation and ozonation. Proton-transfer-reaction mass spectrometry (PTR-MS) was used to provide time resolved data for a range of VOC, NH3 and H2S. VOC included organic sulfur compounds, carboxylic acids, phenols, indoles, alcohols, ketones and aldehydes. H2S emission was remarkably observed to take place only in the initial minutes after slurry application, which is explained by its high partitioning into the air phase. Long-term odor effects are therefore assessed to be mainly due to other volatile compounds with low odor threshold values, such as 4-methylphenol. PTR-MS signal assignment was verified by comparison to a photo-acoustic analyzer (NH3) and to thermal desorption GC/MS (VOC). Due to initial rapid changes in odorant emissions and low concentrations of odorants, PTR-MS is assessed to be a very useful method for assessing odor following field application of slurry. The effects of treatments on odorant emissions are discussed.

  13. Application of PTR-MS for Measuring Odorant Emissions from Soil Application of Manure Slurry

    PubMed Central

    Feilberg, Anders; Bildsoe, Pernille; Nyord, Tavs

    2015-01-01

    Odorous volatile organic compounds (VOC) and hydrogen sulfide (H2S) are emitted together with ammonia (NH3) from manure slurry applied as a fertilizer, but little is known about the composition and temporal variation of the emissions. In this work, a laboratory method based on dynamic flux chambers packed with soil has been used to measure emissions from untreated pig slurry and slurry treated by solid-liquid separation and ozonation. Proton-transfer-reaction mass spectrometry (PTR-MS) was used to provide time resolved data for a range of VOC, NH3 and H2S. VOC included organic sulfur compounds, carboxylic acids, phenols, indoles, alcohols, ketones and aldehydes. H2S emission was remarkably observed to take place only in the initial minutes after slurry application, which is explained by its high partitioning into the air phase. Long-term odor effects are therefore assessed to be mainly due to other volatile compounds with low odor threshold values, such as 4-methylphenol. PTR-MS signal assignment was verified by comparison to a photo-acoustic analyzer (NH3) and to thermal desorption GC/MS (VOC). Due to initial rapid changes in odorant emissions and low concentrations of odorants, PTR-MS is assessed to be a very useful method for assessing odor following field application of slurry. The effects of treatments on odorant emissions are discussed. PMID:25585103

  14. The effect of long or chopped straw on pig behaviour.

    PubMed

    Lahrmann, H P; Oxholm, L C; Steinmetz, H; Nielsen, M B F; D'Eath, R B

    2015-05-01

    In the EU, pigs must have permanent access to manipulable materials such as straw, rope, wood, etc. Long straw can fulfil this function, but can increase labour requirements for cleaning pens, and result in problems with blocked slatted floors and slurry systems. Chopped straw might be more practical, but what is the effect on pigs' behaviour of using chopped straw instead of long straw? Commercial pigs in 1/3 slatted, 2/3 solid pens of 15 pigs were provided with either 100 g/pig per day of long straw (20 pens) or of chopped straw (19 pens). Behavioural observations were made of three focal pigs per pen (one from each of small, medium and large weight tertiles) for one full day between 0600 and 2300 h at each of ~40 and ~80 kg. The time spent rooting/investigating overall (709 s/pig per hour at 40 kg to 533 s/pig per hour at 80 kg), or directed to the straw/solid floor (497 s/pig per hour at 40 kg to 343 s/pig per hour at 80 kg), was not affected by straw length but reduced with age. Time spent investigating other pigs (83 s/pig per hour at 40 kg), the slatted floor (57 s/pig per hour) or pen fixtures (21 s/pig per hour) was not affected by age or straw length. Aggressive behaviour was infrequent, but lasted about twice as long in pens with chopped straw (2.3 s/pig per hour at 40 kg) compared with pens with long straw (1.0 s/pig per hour at 40 kg, P=0.060). There were no significant effects of straw length on tail or ear lesions, but shoulders were significantly more likely to have minor scratches with chopped straw (P=0.031), which may reflect the higher levels of aggression. Smaller pigs showed more rooting/investigatory behaviour, and in particular directed towards the straw/solid floor and the slatted floor than their larger pen-mates. Females exhibited more straw and pen fixture-directed behaviour than males. There were no effects of pig size or sex on behaviour directed towards other pigs. In summary, pigs spent similar amounts of time interacting with straw

  15. Co-digestion of animal slurry can increase short-term nitrogen recovery by crops.

    PubMed

    de Boer, H C

    2008-01-01

    Co-digestion changes slurry characteristics and is supposed to increase short-term nitrogen (N) uptake by crops after application. A higher N uptake from slurry reduces the need for additional mineral N fertilizer. If farmers apply co-digested slurry (CS), a higher N recovery has to be taken into account to prevent losses to the environment. Since data on the effects of co-digestion on N recovery by crops are scarce, a pot experiment was performed. The apparent N recovery (ANR) of five different co-digested pig slurries was compared with their raw source slurries (RS) during 105 d after a single fertilization of ryegrass (Lolium perenne L.), grown under controlled conditions. Slurry was mixed with sandy soil and grass was cut every 35 d. The results show that co-digestion increased (p < 0.05) the ANR at first cut on average from 39 to 50%, at second cut from 7 to 9% (p < 0.05), and had no effect on ANR at third cut (3%). The ANR increase at first cut was likely due to an increase of the NH(4)-N/total N ratio along with a decrease of the organic C/total N ratio of slurry during co-digestion. Field application may under certain circumstances decrease N fertilizer value of CS, due to a higher NH(3) emission compared to RS. A potential ANR increase may then be reduced, absent, or even become a decrease. Under comparable NH(3) emissions, however, CS can in the short term be more valuable as an N fertilizer than RS, and fertilizer savings can likely be realized.

  16. Gaseous emissions from the storage of untreated slurries and the fractions obtained after mechanical separation

    NASA Astrophysics Data System (ADS)

    Dinuccio, E.; Berg, W.; Balsari, P.

    A laboratory-scale study was set up to investigate ammonia (NH 3), nitrous oxide (N 2O), carbon dioxide (CO 2) and methane (CH 4) emissions during storage of untreated pig and cattle slurry and the fractions (solid and liquid) obtained by mechanical separation. The solid and liquid fractions were obtained from the same untreated slurry by means of a lab-scale mechanical separator. The manures were stored for a period of 30 days in open vessels (1500 cm 3 capacity) in two temperature-controlled rooms, which were kept at 5±0.5 and 25±0.2 °C. Gaseous emissions were determined using a dynamic chamber method and infrared photoacoustic detection (IPD). Over the storage period, gaseous emissions from pig manures were significantly ( P<0.05) higher than those from cattle manures. N 2O fluxes of up to 232 mg m -2 h -1 were measured, but from pig solid fraction only. Between 40.8% (from pig liquid fraction stored at 25 °C) and 3.60% (from untreated cattle slurry stored at 25 °C) of the initial nitrogen content of the manures was lost as NH 3. Over the 30-day-storage period, the predominant emission of carbon was in the CO 2 form. Total C-CH 4 losses, expressed as a percent of the carbon initially present in the volatile solids (C-VS), ranged from 0.60% to 12.8% for pig manures and from 0.23% to 1.56% for cattle manures. The mechanical separation of cattle slurry increased by up to 30% the emissions of CO 2 equivalents to the atmosphere, during the storage of the separated fractions, when compared with the slurries. Results indicated that NH 3, N 2O, CO 2 and CH 4 emissions were affected by the interaction between a number of variables, including storage temperature, chemical characteristics and type of manure. Results also indicated that mechanical separation does not reduce emissions, but has the potential to increase the emissions of CO 2 equivalents to the atmosphere during the storage of the separated fractions.

  17. Managing ammonia emissions from dairy cows by amending slurry with alum or zeolite or by diet modification.

    PubMed

    Meisinger, J J; Lefcourt, A M; Van Kessel, J A; Wilkerson, V

    2001-10-27

    Animal agriculture is a significant source of atmospheric ammonia. Ammonia (NH3) volatilization represents a loss of plant available N to the farmer and a potential contributor to eutrophication in low-nitrogen input ecosystems. This research evaluated on-farm slurry treatments of alum or zeolite and compared three diets for lactating dairy cows in their effectiveness to reduce NH3 emissions. NH3 emissions were compared using a group of mobile wind tunnels. The addition of 2.5% alum or 6.25% zeolite to barn-stored dairy slurry reduced NH3 volatilization by 60% and 55%, respectively, compared to untreated slurry. The alum conserved NH3 by acidifying the slurry to below pH 5, while the zeolite conserved ammonia by lowering the solution-phase nitrogen through cation exchange. The use of alum or zeolite also reduced soluble phosphorus in the slurry. NH3 loss from fresh manure collected from lactating dairy cows was not affected by three diets containing the same level of crude protein but differing in forage source (orchardgrass silage vs. alfalfa silage) or neutral detergent fiber (NDF) content (30% vs. 35% NDF). NH3 losses from the freshly excreted manures occurred very rapidly and included the urea component plus some unidentified labile organic nitrogen sources. NH3 conservation strategies for fresh manures will have to be active within the first few hours after excretion in order to be most effective. The use of alum or zeolites as an on-farm amendment to dairy slurry offers the potential for significantly reducing NH3 emissions.

  18. Prior exposure influences the behavioural avoidance by an intertidal gastropod, Bembicium auratum, of acidified waters

    NASA Astrophysics Data System (ADS)

    Amaral, Valter; Cabral, Henrique N.; Bishop, Melanie J.

    2014-01-01

    Phenotypic plasticity may be critical to the maintenance of viable populations under future environmental change. Here we examined the role of behavioural avoidance of sub-optimal conditions in enabling the intertidal gastropod, Bembicium auratum, to persist in mangrove forests affected by the low pH runoff from acid sulphate soils (ASS). Behaviourally, the gastropod may be able to avoid periods of particularly high acidity by using pneumatophores and/or mangrove trunks to vertically migrate above the water line or by retreating into its shell. We hypothesised that (1) B. auratum would display greater and more rapid vertical migration out of acidified than reference estuarine waters, and (2) responses would be more pronounced in gastropods collected from acidified than reference sites. Gastropods from acidified sites showed significantly higher activity in and more rapid migration out of acidified waters of pH 6.2-7.0, than reference waters or waters of pH < 5.0. Gastropods from reference locations showed a significantly weaker response to acidified water than those from acidified waters, and which did not significantly differ from their response to reference water. At extremely low pHs, <5.0, a higher proportion of both acidified and reference gastropods retreated into their shell than at higher pHs. Both the migration of gastropods out of acidified waters and retraction into their shells serves to reduce exposure time to acidified waters and may reduce the impact of this stressor on their populations. The stronger response to acidification of gastropods from populations previously exposed to this stressor suggests that the response may be learned, inherited or induced over multiple exposures. Our study adds to growing evidence that estuarine organisms may exhibit considerable physiological and behaviour adaptive capacity to acidification. The potential for such adaptive capacity should be incorporated into studies seeking to forecast impacts to marine organisms

  19. Reduction of hexavalent chromium in water samples acidified for preservation

    USGS Publications Warehouse

    Stollenwerk, K.G.; Grove, D.B.

    1985-01-01

    Reduction of hexavalent chromium, Cr(VI), in water samples, preserved by standard techniques, was investigated. The standard preservation technique for water samples that are to be analyzed for Cr(VI) consists of filtration through a 0.45-??m membrane, acidification to a pH < 2, and storage in plastic bottles. Batch experiments were conducted to evaluate the effect of H+ concentration, NO2, temperature, and dissolved organic carbon (DOC) on the reduction of Cr(VI) to Cr(III). The rate of reduction of Cr(VI) to Cr(III) increased with increasing NO2, DOC, H+, and temperature. Reduction of Cr(VI) by organic matter occurred in some samples even though the samples were unacidified. Reduction of Cr(VI) is inhibited to an extent by storing the sample at 4??C. Stability of Cr(VI) in water is variable and depends on the other constituents present in the sample. Water samples collected for the determination of Cr(VI) should be filtered (0.45-??m membrane), refrigerated, and analyzed as quickly as possible. Water samples should not be acidified. Measurement of total Cr in addition to Cr(VI) can serve as a check for Cr(VI) reduction. If total Cr is greater than Cr(VI), the possibility that Cr(VI) reduction has occurred needs to be considered.The rate of reduction of Cr(VI) to Cr(III) increased with increasing NO//2, DOC, H** plus , and temperature. Reduction of Cr(VI) by organic matter occurred in some samples even though the samples were unacidified. Reduction of Cr(VI) is inhibited to an extent by storing the sample at 4 degree C. Stability of Cr(VI) in water is variable and depends on the other constituents present in the sample. Water samples collected for the determination of Cr(VI) should be filtered (0. 45- mu m membrane), refrigerated, and analyzed as quickly as possible. Water samples should not be acidified. Measurement of total Cr in addition to Cr(VI) can serve as a check for Cr(VI) reduction. If total Cr is greater than Cr(VI), the possibility that Cr

  20. Method and apparatus for transporting liquid slurries

    SciTech Connect

    Berry, G.F.; Lyczkowski, R.W.; Wang, Chi-Sheng.

    1991-01-01

    An improved method and device to prevent erosion of slurry transport devices is disclosed which uses liquid injection to prevent contact by the slurry composition with the inner surface of the walls of the transport system. A non-abrasive liquid is injected into the slurry transport system and maintains intimate contact with the entire inner surface of the transport system, thereby creating a fluid barrier between the nonabrasive liquid and the inner surface of the transport system which thereby prevents erosion.

  1. High temperature well bore cement slurry

    SciTech Connect

    Nahm, J.J.W.; Vinegar, H.J.; Karanikas, J.M.; Wyant, R.E.

    1993-07-13

    A low density well bore cement slurry composition is described suitable for cementing well bores with high reservoir temperatures comprising: (a) a high alumina cement in an amount of about 40 pounds per barrel of slurry or greater: (b) graphite in an amount greater than about one quarter, by volume, of the solids in the cement slurry; and (c) and a carrier fluid comprising drilling mud.

  2. BOILING SLURRY REACTOR AND METHOD FO CONTROL

    DOEpatents

    Petrick, M.; Marchaterre, J.F.

    1963-05-01

    The control of a boiling slurry nuclear reactor is described. The reactor consists of a vertical tube having an enlarged portion, a steam drum at the top of the vertical tube, and at least one downcomer connecting the steam drum and the bottom of the vertical tube, the reactor being filled with a slurry of fissionabie material in water of such concentration that the enlarged portion of the vertical tube contains a critical mass. The slurry boils in the vertical tube and circulates upwardly therein and downwardly in the downcomer. To control the reactor by controlling the circulation of the slurry, a gas is introduced into the downcomer. (AEC)

  3. RPP-WTP Slurry Wear Evaluation: Slurry Abrasivity

    SciTech Connect

    Duignan, M.R.

    2002-06-03

    This report deals with the task of evaluating wear in the cross-flow ultrafiltration system and specifically the need to define a representative slurry in order to obtain prototypic wear rates. The filtration system will treat many different wastes, but it is not practical to run a test for each one. This is especially true when considering that the planned period for testing is 2000 hours long and procurement of appropriate simulants is costly. Considering time and cost, one waste stream needs to be chosen to perform the wear test.

  4. Emission of ESBL/AmpC-producing Escherichia coli from pig fattening farms to surrounding areas.

    PubMed

    von Salviati, Christina; Laube, Henriette; Guerra, Beatriz; Roesler, Uwe; Friese, Anika

    2015-01-30

    The presence of ESBL/AmpC-producing Escherichia coli in livestock such as pigs has been known for some time. However, to date there is little information about the transmission of these resistant bacteria between pig farms and their surroundings. Thus, the aim of this study was to explore this topic by investigating seven German pig fattening farms. Samples from outside (including ground surfaces, ambient air, slurry and digestate from biogas plants) and, in parallel, from inside the pig barns (including pig feces, dust, barn air, flies and mice feces) were examined for ESBL/AmpC-producing E. coli and selected isolates were compared by pulsed-field gel electrophoresis (PFGE) analysis. 14/17 (82.4%) slurry samples and three of four samples of digestate from biogas plants tested positive for ESBL/AmpC-producing E. coli. In the vicinity of the pig barns these resistant bacteria were detected in 14/87 (16.1%) boot swabs taken from various ground surfaces and in 2/36 (6%) ambient air samples. Inside the pig barns, 6/63 (9.5%) barn air samples and a small proportion of flies and mice feces samples were ESBL/AmpC-positive. PFGE analysis proved fecal emission as well as a possible spread via flies, as identical ESBL-E. coli isolates were detected in slurry and on fertilized fields, as well as in flies and pooled feces from inside the barn and slurry. Contaminated slurry presented the major emission source for ESBL/AmpC-producing E. coli in the pig fattening farms, but a spread via the airborne route or via different vectors also seems possible.

  5. Removal of Suspended Solids in Anaerobically Digested Slurries of Livestock and Poultry Manure by Coagulation Using Different Dosages of Polyaluminum Chloride

    NASA Astrophysics Data System (ADS)

    Li, P.; Zhang, C. J.; Zhao, T. K.; Zhong, H.

    2017-01-01

    In this study, anaerobically digested slurries of livestock and poultry manure were pretreated by coagulation-sedimentation using an inorganic polymer coagulant, polyaluminum chloride (PAC). The effect of different PAC dosages on suspended solids (SS) removal and pH in the biogas slurries was assessed to provide reference values for reducing the organic load of biogas slurry in the coagulation-sedimentation process and explore the feasibility of reducing the difficulty in subsequent utilization or processing of biogas slurry. The results showed that for the pig slurry containing approximately 5000 mg/L SS, the removal rate of SS reached up to 81.6% with the coagulant dosage of 0.28 g/L PAC. For the chicken slurry containing approximately 2600 mg/L SS, the removal rate of SS was 30.2% with the coagulant dosage of 0.33 g/L PAC. The removal rate of SS in both slurries of livestock and poultry manure exhibited a downward trend with high PAC dosage. Therefore, there is a need to control the PAC dosage in practical use. The pH changed little in the two types of biogas slurries after treatment with different PAC dosages and both were in line with the standard values specified in the “Standards for Irrigation Water Quality”.

  6. Effect of temperature and water on gaseous emissions from soils treated with animal slurry

    SciTech Connect

    Maag, M.; Vinther, F.P.

    1999-08-01

    Microbial respiration and denitrification are greatly affected by abiotic factors, but they are difficult to assess in natural environments. Under controlled conditions the interactions between temperature and soil water content on microbial respiration, N{sub 2}O production, and denitrification in soil amended with animal slurries were studied. The effects of the abiotic factors on the biological processes were monitored for 8 wk in repacked soil cores amended with pig or cattle slurry. The soil cores were incubated at 43, 57, and 72% water-filled pore space (WFPS) and at 10, 15, and 20 C with or without addition of 10% acetylene. The amount of N{sub 2}O lost at 72% WFPS corresponded to 8 to 22% of the slurry's NH{sub 4}{sup +} content, but for only 0.01 to 1.2% at 43 to 57% WFPS. The amount of available C accounted for by denitrification was 8 to 16% of total respiration at 72% WFPS, but only 0.03 to 0.4% at 43 to 57% WFPS. Both N{sub 2}O production and denitrification peaked earlier in the cattle-slurry treated soil than in the pig-slurry treated soil, whereas the total N loss was greatest from the latter. Neither amendments nor soil water contents seemed to affect the Q{sub 10}-values for the CO{sub 2} production, resulting in values between 1.6 and 2.6. At 72% WFPS, N{sub 2}O production and denitrification had Q{sub 10}-values ranging between 3.3 and 5.4. High temperatures enhanced both aerobic respiration and denitrification, and aerobic respiration further enhanced denitrification by consuming oxygen, resulting in strong sensitivity of denitrification to temperature.

  7. Optimizing slurry separation in coal preparation

    SciTech Connect

    V.S. Shved; V.H. Fritsler; V.V. Bukhtiyarov

    2009-05-15

    In processing slurry with cationic polyelectrolytes, the final concentration of the suspended particulates in the water beyond the slurry tank in the coal-preparation shop is no more than 10 mg/l. Consequently, this water may be reused in industrial systems.

  8. Single stage high pressure centrifugal slurry pump

    DOEpatents

    Meyer, John W.; Bonin, John H.; Daniel, Arnold D.

    1984-03-27

    Apparatus is shown for feeding a slurry to a pressurized housing. An impeller that includes radial passages is mounted in the loose fitting housing. The impeller hub is connected to a drive means and a slurry supply means which extends through the housing. Pressured gas is fed into the housing for substantially enveloping the impeller in a bubble of gas.

  9. Elevated Colonization of Microborers at a Volcanically Acidified Coral Reef

    PubMed Central

    Enochs, Ian C.; Manzello, Derek P.; Tribollet, Aline; Valentino, Lauren; Kolodziej, Graham; Donham, Emily M.; Fitchett, Mark D.; Carlton, Renee; Price, Nichole N.

    2016-01-01

    Experiments have demonstrated that ocean acidification (OA) conditions projected to occur by the end of the century will slow the calcification of numerous coral species and accelerate the biological erosion of reef habitats (bioerosion). Microborers, which bore holes less than 100 μm diameter, are one of the most pervasive agents of bioerosion and are present throughout all calcium carbonate substrates within the reef environment. The response of diverse reef functional groups to OA is known from real-world ecosystems, but to date our understanding of the relationship between ocean pH and carbonate dissolution by microborers is limited to controlled laboratory experiments. Here we examine the settlement of microborers to pure mineral calcium carbonate substrates (calcite) along a natural pH gradient at a volcanically acidified reef at Maug, Commonwealth of the Northern Mariana Islands (CNMI). Colonization of pioneer microborers was higher in the lower pH waters near the vent field. Depth of microborer penetration was highly variable both among and within sites (4.2–195.5 μm) over the short duration of the study (3 mo.) and no clear relationship to increasing CO2 was observed. Calculated rates of biogenic dissolution, however, were highest at the two sites closer to the vent and were not significantly different from each other. These data represent the first evidence of OA-enhancement of microboring flora colonization in newly available substrates and provide further evidence that microborers, especially bioeroding chlorophytes, respond positively to low pH. The accelerated breakdown and dissolution of reef framework structures with OA will likely lead to declines in structural complexity and integrity, as well as possible loss of essential habitat. PMID:27467570

  10. Are ammonia emissions from field-applied slurry substantially over-estimated in European emission inventories?

    NASA Astrophysics Data System (ADS)

    Sintermann, J.; Neftel, A.; Ammann, C.; Häni, C.; Hensen, A.; Loubet, B.; Flechard, C. R.

    2011-10-01

    The EMEP/EEA guidebook 2009 for agricultural emission inventories reports average ammonia (NH3) emission factors (EF) by volatilisation of 55% of the applied total ammoniacal nitrogen (TAN) content for cattle slurry, and 35% losses for pig slurry, irrespective of the type of surface or slurry characteristics such as dry matter content and pH. In this review article, we compiled over 350 measurements of EFs published between 1991 and 2011. The standard slurry application technique during the early years of this period, when a large number of measurements were made, was spreading by splash plate, and as a result reference EFs given in many European inventories are predominantly based on this technique. However, slurry application practices have evolved since then, while there has also been a shift in measurement techniques and investigated plot sizes. We therefore classified the available measurements according to the flux measurement technique, measurement plot size, the year of measurement, and the year of publication. Medium size plots (usually circles between 20 to 50 m radius) generally yielded the highest EFs. The most commonly used measurement setups at this scale were based on the Integrated Horizontal Flux method (IHF or the ZINST method (a simplified IHF method)). Several empirical models were published in the years 1993 to 2003 predicting NH3 EFs as a function of meteorology and slurry characteristics (Menzi et al., 1998; Søgaard et al., 2002). More recent measurements that appeared subsequently show substantially lower EFs, and appear to indicate a need for a revision of the EF in emission inventories.

  11. Are ammonia emissions from field-applied slurry substantially over-estimated in European emission inventories?

    NASA Astrophysics Data System (ADS)

    Sintermann, J.; Neftel, A.; Ammann, C.; Häni, C.; Hensen, A.; Loubet, B.; Flechard, C. R.

    2012-05-01

    The EMEP/EEA guidebook 2009 for agricultural emission inventories reports an average ammonia (NH3) emission factor (EF) by volatilisation of 55% of the applied total ammoniacal nitrogen (TAN) content for cattle slurry, and 35% losses for pig slurry, irrespective of the type of surface or slurry characteristics such as dry matter content and pH. In this review article, we compiled over 350 measurements of EFs published between 1991 and 2011. The standard slurry application technique during the early years of this period, when a large number of measurements were made, was spreading by splash plate, and as a result reference EFs given in many European inventories are predominantly based on this technique. However, slurry application practices have evolved since then, while there has also been a shift in measurement techniques and investigated plot sizes. We therefore classified the available measurements according to the flux measurement technique or measurement plot size and year of measurement. Medium size plots (usually circles between 20 to 50 m radius) generally yielded the highest EFs. The most commonly used measurement setups at this scale were based on the Integrated Horizontal Flux method (IHF or the ZINST method (a simplified IHF method)). Several empirical models were published in the years 1993 to 2003 predicting NH3 EFs as a function of meteorology and slurry characteristics (Menzi et al., 1998; Søgaard et al., 2002). More recent measurements show substantially lower EFs which calls for new measurement series in order to validate the various measurement approaches against each other and to derive revised inputs for inclusion into emission inventories.

  12. Coal slurry rheology and chemistry

    SciTech Connect

    Lynch, A.W.; Cook, D.W.

    1987-09-01

    Three well-characterized, generic surfactants (nonionic, anionic and cationic) were used to modify coal/water mixtures by changing the interaction between several coals of different rank and the slurry liquor. Each experiment involved one coal and one surfactant per experiment. The analytical and rheological results from these experiments have been previously reported. The thrust of the current program is to extend the work to shear rates expected during atomization. The program consists of the following elements: (1) design, fabricate and test a helical screw rheometer capable of developing shear rates to 10,000 sec/sup -1/; (2) establish a capability to atomize slurries and monitor the spray using high speed photography; and (3) initiate a collaborative program with the Combustion Research Facility at Sandia National Laboratories Livermore for the purpose of analyzing particulates in atomized and burned sprays. The helical screw rheometer was designed using technology developed for polymer processing. The rheometer acts as an extrusion pump when there is discharge of fluid, but when flow is interrupted a differential pressure develops across the length of the screw. Using the mathematical analysis developed for screw pumps, the rotation rate of the screw may be translated to shear rate and the differential pressure translated to shear stress. 9 refs., 11 figs.

  13. Slurry-pressing consolidation of silicon nitride

    NASA Technical Reports Server (NTRS)

    Sanders, William A.; Kiser, James D.; Freedman, Marc R.

    1988-01-01

    A baseline slurry-pressing method for a silicon nitride material is developed. The Si3N4 composition contained 5.8 wt percent SiO2 and 6.4 wt percent Y2O3. Slurry-pressing variables included volume percent solids, application of ultrasonic energy, and pH. Twenty vol percent slurry-pressed material was approximately 11 percent stronger than both 30 vol percent slurry-pressed and dry-pressed materials. The Student's t-test showed the difference to be significant at the 99 percent confidence level. Twenty volume percent (300 h) slurry-pressed test bars exhibited strengths as high as 980 MPa. Large, columnar beta-Si3N4 grains caused failure in the highest strength specimens. The improved strength correlated with better structural uniformity as determined by radiography, optical microscopy, and image analysis.

  14. Process for heating coal-oil slurries

    DOEpatents

    Braunlin, W.A.; Gorski, A.; Jaehnig, L.J.; Moskal, C.J.; Naylor, J.D.; Parimi, K.; Ward, J.V.

    1984-01-03

    Controlling gas to slurry volume ratio to achieve a gas holdup of about 0.4 when heating a flowing coal-oil slurry and a hydrogen containing gas stream allows operation with virtually any coal to solvent ratio and permits operation with efficient heat transfer and satisfactory pressure drops. The critical minimum gas flow rate for any given coal-oil slurry will depend on numerous factors such as coal concentration, coal particle size distribution, composition of the solvent (including recycle slurries), and type of coal. Further system efficiency can be achieved by operating with multiple heating zones to provide a high heat flux when the apparent viscosity of the gas saturated slurry is highest. Operation with gas flow rates below the critical minimum results in system instability indicated by temperature excursions in the fluid and at the tube wall, by a rapid increase and then decrease in overall pressure drop with decreasing gas flow rate, and by increased temperature differences between the temperature of the bulk fluid and the tube wall. At the temperatures and pressures used in coal liquefaction preheaters the coal-oil slurry and hydrogen containing gas stream behaves essentially as a Newtonian fluid at shear rates in excess of 150 sec[sup [minus]1]. The gas to slurry volume ratio should also be controlled to assure that the flow regime does not shift from homogeneous flow to non-homogeneous flow. Stable operations have been observed with a maximum gas holdup as high as 0.72. 29 figs.

  15. Process for heating coal-oil slurries

    DOEpatents

    Braunlin, Walter A.; Gorski, Alan; Jaehnig, Leo J.; Moskal, Clifford J.; Naylor, Joseph D.; Parimi, Krishnia; Ward, John V.

    1984-01-03

    Controlling gas to slurry volume ratio to achieve a gas holdup of about 0.4 when heating a flowing coal-oil slurry and a hydrogen containing gas stream allows operation with virtually any coal to solvent ratio and permits operation with efficient heat transfer and satisfactory pressure drops. The critical minimum gas flow rate for any given coal-oil slurry will depend on numerous factors such as coal concentration, coal particle size distribution, composition of the solvent (including recycle slurries), and type of coal. Further system efficiency can be achieved by operating with multiple heating zones to provide a high heat flux when the apparent viscosity of the gas saturated slurry is highest. Operation with gas flow rates below the critical minimum results in system instability indicated by temperature excursions in the fluid and at the tube wall, by a rapid increase and then decrease in overall pressure drop with decreasing gas flow rate, and by increased temperature differences between the temperature of the bulk fluid and the tube wall. At the temperatures and pressures used in coal liquefaction preheaters the coal-oil slurry and hydrogen containing gas stream behaves essentially as a Newtonian fluid at shear rates in excess of 150 sec.sup. -1. The gas to slurry volume ratio should also be controlled to assure that the flow regime does not shift from homogeneous flow to non-homogeneous flow. Stable operations have been observed with a maximum gas holdup as high as 0.72.

  16. Method and apparatus for transporting liquid slurries

    DOEpatents

    Berry, G.F.; Lyczkowski, R.W.; Chisheng Wang.

    1993-03-16

    An improved method and device to prevent erosion of slurry transport devices is disclosed which uses liquid injection to prevent contact by the slurry composition with the inner surface of the walls of the transport system. A non-abrasive liquid is injected into the slurry transport system and maintains intimate contact with the entire inner surface of the transport system, thereby creating a fluid barrier between the non-abrasive liquid and the inner surface of the transport system which thereby prevents erosion.

  17. Method and apparatus for transporting liquid slurries

    DOEpatents

    Berry, Gregory F.; Lyczkowski, Robert W.; Wang, Chi-Sheng

    1993-01-01

    An improved method and device to prevent erosion of slurry transport devices is disclosed which uses liquid injection to prevent contact by the slurry composition with the inner surface of the walls of the transport system. A non-abrasive liquid is injected into the slurry transport system and maintains intimate contact with the entire inner surface of the transport system, thereby creating a fluid barrier between the non-abrasive liquid and the inner surface of the transport system which thereby prevents erosion.

  18. Trace metal biogeochemistry in mangrove ecosystems: a comparative assessment of acidified (by acid sulfate soils) and non-acidified sites.

    PubMed

    Nath, Bibhash; Birch, Gavin; Chaudhuri, Punarbasu

    2013-10-01

    The generation of acidity and subsequent mobilization of toxic metals induced by acid sulfate soils (ASSs) are known to cause severe environmental damage to many coastal wetlands and estuaries of Australia and worldwide. Mangrove ecosystems serve to protect coastal environments, but are increasingly threatened from such ASS-induced acidification due to variable hydrological conditions (i.e., inundation-desiccation cycles). However, the impact of such behaviors on trace metal distribution, bio-availability and accumulation in mangrove tissues, i.e., leaves and pneumatophores, are largely unknown. In this study, we examined how ASS-induced acidifications controlled trace metal distribution and bio-availability in gray mangrove (Avicennia marina) soils and in tissues in the Kooragang wetland, New South Wales, Australia. We collected mangrove soils, leaves and pneumatophores from a part of the wetland acidified from ASS (i.e., an affected site) for detailed biogeochemical studies. The results were compared with samples collected from a natural intertidal mangrove forest (i.e., a control site) located within the same wetland. Soil pH (mean: 5.90) indicated acidic conditions in the affected site, whereas pH was near-neutral (mean: 7.17) in the control site. The results did not show statistically significant differences in near-total and bio-available metal concentrations, except for Fe and Mn, between affected and control sites. Iron concentrations were significantly (p values≤0.001) greater in the affected site, whereas Mn concentrations were significantly (p values≤0.001) greater in the control site. However, large proportions of near-total metals were potentially bio-available in control sites. Concentrations of Fe and Ni were significantly (p values≤0.001) greater in leaves and pneumatophores of the affected sites, whereas Mn, Cu, Pb and Zn were greater in control sites. The degree of metal bio-accumulation in leaves and pneumatophores suggest contrasting

  19. The effects of four acidifying sprays, vinegar, and water on canine cutaneous pH levels.

    PubMed

    Matousek, Jennifer L; Campbell, Karen L; Kakoma, Ibulaimu; Schaeffer, David J

    2003-01-01

    This study determined the extent and duration of cutaneous acidification caused by a single application of four acidifying sprays, vinegar, and water. Multivariate repeated measures analysis of variance revealed a significant difference between the six sprays (F = 15.3; P < or = 0.001). Linear contrast tests showed that the effects of the acidifying sprays were significantly different from vinegar and water (F = 6.0; P < or = 0.001), and vinegar was significantly different from water (F = 13.8; P < or = 0.001). The acidifying sprays decreased cutaneous pH to < 6.0 for a mean range of 50 to 65 hours, while vinegar did so for a mean of 12 hours.

  20. Nutrient cycling and the growth of benthic algae in experimentally acidified Little Rock Lake, WI

    SciTech Connect

    Detenbeck, N.E.

    1987-01-01

    Changes in nutrient-cycling and the growth of benthic algae resulting from decreased pH in low alkalinity lake systems were analyzed by laboratory, mesocosm, and whole-lake studies on Little Rock Lake, Wisconsin. Nutrients, transparency, an algal growth in the experimentally acidified basin were compared with conditions in an untreated reference basin. During the first summer following acidification (1985), accumulation rates of attached algae were significantly higher in the acidified basin than in the reference basin during June-August, but not in September. Color and winter silica values were significantly lower in the acidified basin relative to the reference basin following treatment. In addition, the lack of a fall decline in SiO/sub 2/ in the north basin in 1986 may signal pH-related changes in siliceous algal communities.

  1. Fluidization mechanisms in slurry flows

    NASA Astrophysics Data System (ADS)

    Campbell, Charles S.

    1988-08-01

    A transducer is developed to measure particle pressures independently from fluid pressure. Initially it was thought that particle pressure was the only path by which the fluidization mechanism could be determined. The particle pressure transducer has been described in previous reports. A secondary project was developed to test these transducers and use them to measure the particle pressures generated against the side walls of gas-fluidized beds. This was a way to gain experience with the particle pressure transducer while awaiting the delivery of the pump and other components for the slurry pipe loop. Earlier this year, there was great difficulty in gaining repeatable results from the experiments. The culprit turned out to be static charge buildup in the granular mass. Hence, steam was injected into the air stream to help dissipate the charge buildup. This produced a further source of error that was eventually traced to the fiberoptic displacement transducer inside the probe. It developed that the transducer was sensitive to humidity. It has been suggested that this reaction might be a byproduct of the absorption of water onto the sensing surface changes its optical properties and hence its output signal.

  2. The rheology and stability of concentrated coal water slurries

    SciTech Connect

    Slaczka, A.; Piszczynski, Z.

    1995-12-31

    An experimental study was undertaken to investigate the rheological properties of coal-water slurries (CWS). Slurries were prepared from coal of different rank, different particle size distribution, additives and solid content. Viscosity at different shear rate were measured using a capillary viscometer specially constructed by the authors for this purpose. The stability of investigated CWS was performed too. The study has revealed a correlation between the rank of coal used for slurry preparation and its viscosity in all ranges of slurry concentration. The addition of some reagents causes a considerable decrease in the slurry viscosity. The stability of the slurry was improved too.

  3. The effect of slurry treatment including ozonation on odorant reduction measured by in-situ PTR-MS

    NASA Astrophysics Data System (ADS)

    Liu, Dezhao; Feilberg, Anders; Adamsen, Anders P. S.; Jonassen, Kristoffer E. N.

    2011-07-01

    The emission of odorous compounds from intensive pig production facilities is a nuisance for neighbors. Slurry ozonation for odor abatement has previously been demonstrated in laboratory scale. In this study, the effect of slurry ozonation (combined with solid-liquid pre-separation and acidification) on emissions of odorous compounds was tested in an experimental full-scale growing pig facility using Proton-Transfer-Reaction Mass Spectrometry (PTR-MS) for online analysis of odorants. The measurements were performed to gain a better understanding of the effects of ozone treatment on emissions odorous compounds and to identify potential options for optimization of ozone treatment. The compounds monitored included volatile sulfur compounds, amine, carboxylic acids, ketones, phenols and indoles. Measurements were performed during nearly a one-month period in summertime. The compounds with the highest concentrations observed in the ventilation exhaust duct were acetic acid, hydrogen sulfide, propanoic acid and butanoic acid. The compounds with the highest removal efficiencies were hydrogen sulfide, 3-methyl-indole, phenol and acetic acid. Based on odor threshold values, methanethiol, butanoic acid, 4-methylphenol, hydrogen sulfide and C 5 carboxylic acids are estimated to contribute significantly to the odor nuisance. Emissions of odorous compounds were observed to be strongly correlated with temperature with the exception of hydrogen sulfide. Emission peaks of sulfur compounds were seen during slurry handling activities. Discharging of the slurry pit led to reduced hydrogen sulfide emissions, but emissions of most other odorants were not affected. The results indicate that emissions of odorants other than hydrogen sulfide mainly originate from sources other than the treated slurry, which limits the potential for further optimization. The PTR-MS measurements are demonstrated to provide a quantitative, accurate and detailed evaluation of ozone treatment for emission

  4. [Study the restoration technology of concentrated application-natural diffusion about amendments of acidified soil of hilly woodland].

    PubMed

    Fang, Xiong; Liu, Ju-Xiu; Yin, Guang-Cai; Zhao, Liang; Liu, Shi-Zhong; Chu, Guo-Wei; Li, Yi-Yong

    2013-01-01

    Through concentrated application of lime, sewage sludge and lime + sewage sludge on the sloping top of the hilly woodlands, the restoration effects of the three soil amendments on the acidified soil of hilly woodland were studied. The results showed that: (1) Joint application of sewage sludge + lime can significantly (P < 0.05) decrease soil acidity, promote the rapid increase in soil organic matter and nitrogen content, increase soil cation exchange capacity, and effectively improve acidified soil. (2) Through natural diffusion mechanisms of surface and subsurface runoff, a large area of acidified soil of hilly woodlands can be restored by concentrated application of soil amendments on the sloping top of the hilly woodlands. (3) It is conducive to solve the pollution problems of the urban sewage sludge by using municipal sewage sludge to restore acidified soil, but only for the restoration of acidified soil of timber forest.

  5. The Reaction between Iron(II) Iodide and Potassium Dichromate(VI) in Acidified Aqueous Solution

    ERIC Educational Resources Information Center

    Talbot, Christopher

    2013-01-01

    This "Science note" teaching lesson explores the possible reaction between the ions in a reaction mixture consisting of iron(II) iodide and potassium dichromate(VI) in acidified aqueous solution. The electrode potentials will be used to deduce any spontaneous reactions under standard thermodynamic conditions (298 K, 1 bar (approximately…

  6. Quality evaluation of packaged acidified vegetables subjected to continuous microwave pasteurization

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The study evaluated the use of 915 MHz continuous microwave processing with a rotation apparatus for pasteurization of acidified vegetable packages. Broccoli florets, and 1.2 cm cubes of broccoli stems, red bell pepper, and sweetpotato were pre-equilibrated to 1 g/100 g NaCl and 0.38 g/100 mL citric...

  7. The chemical behavior of acidified chromium (3) solutions. B.S. Thesis

    NASA Technical Reports Server (NTRS)

    Terman, D. K.

    1981-01-01

    A unique energy-storage system has been developed at NASA's Lewis Research Center called REDOX. This NASA-REDOX system is an electrochemical storage device that utilized the oxidation and reduction of two fully soluble redox couples for charging and discharging. The redox couples now being investigated are acidified chloride solutions of chromium (Cr(+2)/Cr(+3)) and iron (Fe(+2)/Fe(+3)).

  8. Rheological properties of defense waste slurries

    SciTech Connect

    Ebadian, M.A.

    1998-01-01

    The major objective of this two-year project has been to obtain refined and reliable experimental data about the rheological properties of melter feeds. The research has involved both experimental studies and model development. Two experimental facilities have been set up to measure viscosity and pressure drop. Mathematical models have been developed as a result of experimental observation and fundamental rheological theory. The model has the capability to predict the viscosity of melter slurries in a range of experimental conditions. The final results of the investigation could be used to enhance the current design base for slurry transportation systems and improve the performance of the slurry mixing process. If successful, the cost of this waste treatment will be reduced, and disposal safety will be increased. The specific objectives for this project included: (1) the design, implementation, and validation of the experimental facility in both batch and continuous operating modes; (2) the identification and preparation of melter feed samples of both the SRS and Hanford waste slurries at multiple solids concentration levels; (3) the measurement and analysis of the melter feeds to determine the effects of the solids concentration, pH value, and other factors on the rheological properties of the slurries; (4) the correlation of the rheological properties as a function of the measured physical and chemical parameters; and (5) transmission of the experimental data and resulting correlation to the DOE site user to guide melter feed preparation and transport equipment design.

  9. Dust in an acidified ocean: iron bioavailability, phytoplankton growth and DMS

    NASA Astrophysics Data System (ADS)

    Mélançon, J.; Levasseur, M.; Lizotte, M.; Scarratt, M. G.; Tremblay, J. E.; Tortell, P. D.; Yang, G.; Shi, G. Y.; Gao, H.; Semeniuk, D.; Robert, M.; Arychuk, M.; Johnson, K.; Sutherland, N.; Davelaar, M.; Nemcek, N.; Pena, A.; Richardson, W.

    2015-12-01

    Ocean acidification (OA) is likely to have an effect on the fertilizing potential of desert dust in high-nutrient, low-chlorophyll oceanic regions, either by modifying Fe speciation and bioavailability, or by altering phytoplankton Fe requirements and acquisition. To address this issue, short incubations (4 days) of northeast subarctic Pacific waters enriched with either FeSO4 or dust, and maintained at pH 8.0 (in situ) and 7.8 were conducted in August 2010. We assessed the impact of a decrease in pH on dissolved Fe concentration, phytoplankton biomass, taxonomy and productivity, and the production of dimethylsulfide (DMS) and its algal precursor dimethylsulfoniopropionate (DMSP). Chlorophyll a (chl a) remained unchanged in the controls and doubled in both the FeSO4-enriched and dust-enriched incubations, confirming the Fe-limited status of the plankton assemblage during the experiment. In the acidified treatments, a significant reduction (by 16-38%) of the final concentration of chl a was measured compared to their non-acidified counterparts, and a 15% reduction in particulate organic carbon (POC) concentration was measured in the dust-enriched acidified treatment compared to the dust-enriched non-acidified treatment. FeSO4 and dust additions had a fertilizing effect mainly on diatoms and cyanobacteria. Lowering the pH affected mostly the haptophytes, but pelagophyte concentrations were also reduced in some acidified treatments. Acidification did not significantly alter DMSP and DMS concentrations. These results show that dust deposition events in a low-pH iron-limited Northeast subarctic Pacific are likely to stimulate phytoplankton growth to a lesser extent than in today's ocean during the few days following fertilization and point to a low initial sensitivity of the DMSP and DMS dynamics to OA.

  10. Effect of Particle Size Distribution on Slurry Rheology: Nuclear Waste Simulant Slurries

    SciTech Connect

    Chun, Jaehun; Oh, Takkeun; Luna, Maria L.; Schweiger, Michael J.

    2011-07-05

    Controlling the rheological properties of slurries has been of great interest in various industries such as cosmetics, ceramic processing, and nuclear waste treatment. Many physicochemical parameters, such as particle size, pH, ionic strength, and mass/volume fraction of particles, can influence the rheological properties of slurry. Among such parameters, the particle size distribution of slurry would be especially important for nuclear waste treatment because most nuclear waste slurries show a broad particle size distribution. We studied the rheological properties of several different low activity waste nuclear simulant slurries having different particle size distributions under high salt and high pH conditions. Using rheological and particle size analysis, it was found that the percentage of colloid-sized particles in slurry appears to be a key factor for rheological characteristics and the efficiency of rheological modifiers. This behavior was shown to be coupled with an existing electrostatic interaction between particles under a low salt concentration. Our study suggests that one may need to implement the particle size distribution as a critical factor to understand and control rheological properties in nuclear waste treatment plants, such as the U.S. Department of Energy’s Hanford and Savannah River sites, because the particle size distributions significantly vary over different types of nuclear waste slurries.

  11. Lightweight Cement Slurries based on vermiculite

    NASA Astrophysics Data System (ADS)

    Minaev, K.; Gorbenko, V.; Ulyanova, O.

    2014-08-01

    The main purpose of the research is to study the lightweight cement slurry based on vermiculite and its parameters in accordance with GOST 1581-96 requirements as well as improvement of its formulation by polymer additives. Analysis of vermiculite-containing mixture providing the lowest density while maintaining other required parameters was conducted. As a cement base, cement PTscT-I-G-CC-1, cement PTscT - 100 and vermiculite M200 and M150 were used. Vermiculite content varied from 10 to 15 %; and water-to-cement-ratio ranged from 0.65 to 0.8. To sum up, despite the fact that lightweight cement slurry based on vermiculite satisfies GOST 1581-96 requirements under laboratory conditions, field studies are necessary in order to make a conclusion about applicability of this slurry for well cementing.

  12. Rocketdyne's advanced coal slurry pumping program

    NASA Technical Reports Server (NTRS)

    Davis, D. E.; Wong, G. S.; Gilman, H. H.

    1977-01-01

    The Rocketdyne Division of Rockwell International Corporation is conducting a program for the engineering, fabrication, and testing of an experimental/prototype high-capacity, high-pressure centrifugal slurry feed pump for coal liquefaction purposes. The abrasion problems in a centrifugal slurry pump are primarily due to the manner in which the hard, solid particles contained in the slurry are transported through the hydraulic flow passages within the pump. The abrasive particles can create scraping, grinding, cutting, and sandblasting effects on the various exposed parts of the pump. These critical areas involving abrasion and impact erosion wear problems in a centrifugal pump are being addressed by Rocketdyne. The mechanisms of abrasion and erosion are being studied through hydrodynamic analysis, materials evaluation, and advanced design concepts.

  13. Fifth international technical conference on slurry transportation. Proceedings

    SciTech Connect

    Linderman, C.W.

    1980-01-01

    The fifth international technical conference on slurry transportation was held March 26-28, 1980, at the Sahara Tahoe, Lake Tahoe, Nevada. The papers deal with the transport of slurries (mostly coal and iron ores) in slurry pipelines. Planned slurry pipelines in the USA are described and the legal problems in getting rights-of-way and water rights. The economics of slurry pipelines and railways are considered in some detail. Finally, technical aspects of such pipelines are considered: design, engineering, pumps, maintenance, etc. Other topics discussed are: marine transport (moorings, terminal facilities and tanker ship design, other slurry media than water (fuel oils, methanol, CO/sub 2/), coarse slurry transport, slurry preparation, water removal and pumps (pulsations and dampering). Thirty-two papers have been entered individually into EDB and ERA; one had been entered previously from other sources. (LTN)

  14. Results of sludge slurry pipeline pluggage tests. [Simulation of Radioactive Slurry Flow

    SciTech Connect

    Fazio, J.M.

    1987-02-06

    Test results of sludge slurry transport through the Interarea Transfer Line (IAL) Mock-up Facility showed little risk of plugging the interarea pipelines with sludge slurry. Plug-free operation of the pipeline was successfully demonstrated by worst case IAL operating scenarios. Pipeline pressure gradients were measured vs. flow rate for comparison with a computer model over a range of sludge slurry rheological properties. A mathematical computer model developed by L. M. Lee is included in this report which will predict pressure drop for Bingham plastic fluid flow in a pipeline. IAL pluggage situations and pumping requirements may be realized from this model. 4 refs., 11 figs., 2 tabs.

  15. Air blast type coal slurry fuel injector

    DOEpatents

    Phatak, Ramkrishna G.

    1986-01-01

    A device to atomize and inject a coal slurry in the combustion chamber of an internal combustion engine, and which eliminates the use of a conventional fuel injection pump/nozzle. The injector involves the use of compressed air to atomize and inject the coal slurry and like fuels. In one embodiment, the breaking and atomization of the fuel is achieved with the help of perforated discs and compressed air. In another embodiment, a cone shaped aspirator is used to achieve the breaking and atomization of the fuel. The compressed air protects critical bearing areas of the injector.

  16. Air blast type coal slurry fuel injector

    DOEpatents

    Phatak, R.G.

    1984-08-31

    A device to atomize and inject a coal slurry in the combustion chamber of an internal combustion engine is disclosed which eliminates the use of a conventional fuel injection pump/nozzle. The injector involves the use of compressed air to atomize and inject the coal slurry and like fuels. In one embodiment, the breaking and atomization of the fuel is achieved with the help of perforated discs and compressed air. In another embodiment, a cone shaped aspirator is used to achieve the breaking and atomization of the fuel. The compressed air protects critical bearing areas of the injector.

  17. Prospects for coal slurry pipelines in California

    NASA Technical Reports Server (NTRS)

    Lynch, J. F.

    1978-01-01

    The coal slurry pipeline segment of the transport industry is emerging in the United States. If accepted it will play a vital role in meeting America's urgent energy requirements without public subsidy, tax relief, or federal grants. It is proven technology, ideally suited for transport of an abundant energy resource over thousands of miles to energy short industrial centers and at more than competitive costs. Briefly discussed are the following: (1) history of pipelines; (2) California market potential; (3) slurry technology; (4) environmental benefits; (5) market competition; and (6) a proposed pipeline.

  18. Study on the degradation of chitosan slurries

    NASA Astrophysics Data System (ADS)

    Martini, Benjamin; Dimida, Simona; De Benedetto, Egidio; Madaghiele, Marta; Demitri, Christian

    In the present work, we measured the degradation rate of different chitosan slurries. Several parameters were monitored such as temperature (25 °C, 37 °C, 50 °C); chitosan concentration (1% and 2% (w/V)); and polymer molecular weight. The samples were tested in dynamic sweep test mode. This test is able to provide a reliable estimation of viscosity variations of the slurries; in turn, these variations could be related to degradation rate of the system in the considered conditions. The resulting information is particularly important especially in applications in which there is a close relationship between physical properties and molecular structure.

  19. Effect of Sweet Orange Fruit Waste Diets and Acidifier on Haematology and Serum Chemistry of Weanling Rabbits

    PubMed Central

    Daudu, Oluremi Martha; Sani, Rahamatu Usman; Adedibu, Iyetunde Ifeyori; Ademu, Lawrence Anebi; Bawa, Gideon Shaibu; Olugbemi, Taiye Sunday

    2014-01-01

    A total of thirty-five mixed breed (35) rabbits of average weight of 700 g aged 5-6 weeks were allocated to seven treatments in a completely randomised design to investigate the effect of sweet orange fruit waste (SOFW) and acidomix acidifier on haematology and serum chemistry. The diets were 0% SOFW, 10% SOFW with 0.5% acidomix, 10% SOFW with 0.7 acidomix, 15% SOFW with 0.5% acidifier, 15% SOFW with 0.7% acidifier, 20% SOFW with 0.5% acidifier, and 20% SOFW with 0.7% acidifier. Blood samples were analyzed for haemoglobin (hb) concentration, white blood cells (WBC), red blood cells (RBC), differential WBC count (lymphocyte, basophil, eosinophil, monocyte, and neutrophil), alanine amino transferase (ALT), alkaline phosphatase (ALP), aspartate amino transferase (AST), total protein, albumin, and globulin. There was no interaction between SOFW and acidifier for the haematological and most of the serum chemistry parameters but significant difference was observed in ALT; however the values were within the normal range. SOFW had no significant effect on all haematological and serum chemistry parameters. Acidomix had significant effect (P < 0.05) on haemoglobin concentration; rabbits fed 0.5% acidomix diets had higher values which were within the normal range. It is therefore concluded that SOFW with acidifier up to 20% had no detrimental effect on serum chemistry and haematology. PMID:26464931

  20. Process for producing high-concentration slurry of coal

    SciTech Connect

    Nakaoji, K.; Itoh, H.; Kamao, M.; Takao, Sh.; Tatsumi, Sh.

    1985-02-19

    High concentrated coal-water slurry is produced by coarsely crushing coal, thereafter pulverizing the coarsely crushed coal, together with water and a slurry dispersant, according to necessity, in a wet-type ball mill, and feeding back one portion of the finely pulverized coal slurry thus obtained into the inlet of the wet-type ball mill.

  1. Development of a phenomenological model for coal slurry atomization

    SciTech Connect

    Dooher, J.P.

    1995-11-01

    Highly concentrated suspensions of coal particles in water or alternate fluids appear to have a wide range of applications for energy production. For enhanced implementation of coal slurry fuel technology, an understanding of coal slurry atomization as a function coal and slurry properties for specific mechanical configurations of nozzle atomizers should be developed.

  2. SEPARATING LIQUID MODERATOR FROM A SLURRY TYPE REACTOR

    DOEpatents

    Vernon, H.C.

    1961-07-01

    A system for evaporating moderator such as D/sub 2/O from an irradiated slurry or sloution characterized by two successive evaproators is described. In the first of these the most troublesome radioactivity dissipates before the slurry becomes too thick to be pumped out; in the second the slurry, now easier to handle, can be safely reduced to a sludge.

  3. CATALYTIC RECOMBINATION OF RADIOLYTIC GASES IN THORIUM OXIDE SLURRIES

    DOEpatents

    Morse, L.E.

    1962-08-01

    A method for the coinbination of hydrogen and oxygen in aqueous thorium oxide-uranium oxide slurries is described. A small amount of molybdenum oxide catalyst is provided in the slurry. This catalyst is applicable to the recombination of hydrogen and/or deuterium and oxygen produced by irradiation of the slurries in nuclear reactors. (AEC)

  4. Agronomic measures of P, Q/I parameters and lysimeter-collectable P in subsurface soil horizons of a long-term slurry experiment.

    PubMed

    Anderson, R; Xia, L

    2001-01-01

    Soils from a long-term slurry experiment established in 1970 at Hillsborough, Northern Ireland, were used in the experiment. The site has a clay loam soil overlying Silurian shale. Seven treatments were used with three replicate plots per treatment under the following manurial regimes: (1) mineral fertiliser supplying 200 kg N, 32 kg P and 160 kg K ha(-1) yr(-1); (2)-(4) pig slurry applied at 50, 100 or 200 m3 ha(-1) yr(-1); (5)-(7) cow slurry applied at 50, 100 or 200 m3 ha(-1) yr(-1). Agronomic measures of P determined on subsurface layers down to 90 cm were compared with sorption isotherm data and rates of desorption. Adsorption isotherms were fitted using a standard Langmuir model. Data were compared with soluble (molybdate-reactive) P levels in soil water collected at 35 and 90 cm using PTFE suction cup lysimeters. Agronomically available P was concentrated in the top 30 cm of soil in all treatments. The accumulation of P in surface layers of the plots was significantly greater in the pig slurry treatments compared to the cow slurry, reflecting the history of P amendments. Nevertheless, over a period of a year, molybdate-reactive phosphorus (MRP) concentrations in lysimeter collections was consistently higher at 35 cm depth in the highest cow slurry treatment (7) compared to the equivalent pig slurry treatment (4). Either the movement of soluble P down the profile is facilitated by the higher organic content of cow slurry or P movement is not directly related to P accumulation in the soils. In addition, it is hypothesised that P movement down the soil profile depends upon two separate mechanisms. First, a 'break' point above which the accumulated P in the surface horizons is less strongly held and therefore amenable to dissolution and movement down the profile. Second, a mechanism by which some solute P from the surface horizons can travel rapidly through horizons of low P status to greater depth in the soil, i.e., by preferential flow.

  5. Perception of the environmental impacts of current and alternative modes of pig production by stakeholder groups.

    PubMed

    Petit, Jean; van der Werf, Hayo M G

    2003-08-01

    The current industrial pig production model is in crisis, due to its association with environmental pollution, doubtful product quality and lack of animal well-being. In Bretagne (France), a region of intensive pig production, a survey of seven stakeholder groups concerned with pig production was conducted, as part of a research programme dedicated to the assessment of the environmental impact of different modes of pig production. A very large majority of pig producers (93%) and their suppliers (100%) considers pig farms as an asset for the region, whereas a majority of scientists (58%), activists (78%) and consumers (54%) sees it as a handicap. Differences among stakeholder groups are minor with respect to the perceived importance of environmental and social issues. Stakeholders agree on the relative level of responsibility of pig farms with respect to specific problems. For all groups unpleasant odours and water quality come first with respect to responsibility, for most groups soil quality comes second, followed by product safety and air quality. For a future improved mode of pig production, 76% of pig producers and their suppliers prefer to adapt the current model, for all other groups the majority prefers an alternative model. While pig producers and their suppliers prefer a slurry-based housing system, all other groups prefer a straw-based system. Pig producers see the slurry-based system as technically superior and associate the straw-based system with poor working conditions, whereas consumers associate the slurry-based system in the first place with poor water quality and associate the straw-based system with less pollution. These results will be of use in the research programme on the environmental impact of modes of pig production, as they indicate the environmental impacts to be considered and their relative importance. The results will also help in deciding which options should be assessed. It is concluded that the poor image of the current pig

  6. Comparison of raw dairy manure slurry and anaerobically digested slurry as N sources for grass forage production

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Our study was conducted to determine how raw dairy slurry and anaerobically digested slurry (dairy slurry and food waste) applied via broadcast and subsurface deposition to reed canary grass (Phalaris arundinacea) affected forage biomass, N uptake, apparent nitrogen recovery (ANR), and soil nitrate...

  7. Freeforming objects with low-binder slurry

    DOEpatents

    Cesarano, III, Joseph; Calvert, Paul D.

    2000-01-01

    In a rapid prototyping system, a part is formed by depositing a bead of slurry that has a sufficient high concentration of particles to be pseudoplastic and almost no organic binders. After deposition the bead is heated to drive off sufficient liquid to cause the bead to become dilatant.

  8. Dispersant for aqueous slurry of coal powder

    SciTech Connect

    Moriyama, N.; Watanabe, S.; Yamamura, M.

    1982-05-18

    A dispersant for forming an aqueous slurry of coal powder having a good flowability, which comprises as the active ingredient at least one member selected from sulfonation products of polycyclic aromatic compounds which may have a hydrocarbon group as a substituent, salts thereof and formaldehyde condensates thereof.

  9. Coal slurry combustion and technology. Volume 2

    SciTech Connect

    Not Available

    1983-01-01

    Volume II contains papers presented at the following sessions of the Coal Slurry Combustion and Technology Symposium: (1) bench-scale testing; (2) pilot testing; (3) combustion; and (4) rheology and characterization. Thirty-three papers have been processed for inclusion in the Energy Data Base. (ATT)

  10. Low Cost Dewatering of Waste Slurries

    NASA Technical Reports Server (NTRS)

    Peterson, J. B.; Sharma, S. K.; Church, R. H.; Scheiner, B. J.

    1993-01-01

    The U.S. Bureau of Mines has developed a technique for dewatering mineral waste slurries which utilizes polymer and a static screen. A variety of waste slurries from placer gold mines and crushed stone operations have been successfully treated using the system. Depending on the waste, a number of polymers have been used successfully with polymer costs ranging from $0.05 to $0.15 per 1,000 gal treated. The dewatering is accomplished using screens made from either ordinary window screen or wedge wire. The screens used are 8 ft wide and 8 ft long. The capacity of the screens varies from 3 to 7 gpm/sq. ft. The water produced is acceptable for recycling to the plant or for discharge to the environment. For example, a fine grain dolomite waste slurry produced from a crushed stone operation was dewatered from a nominal 2.5 pct solids to greater than 50 pct solids using $0.10 to $0.15 worth of polymer per 1,000 gal of slurry. The resulting waste water had a turbidity of less than 50 NTU and could be discharged or recycled. The paper describes field tests conducted using the polymer-screen dewatering system.

  11. The coal slime slurry combustion technology

    SciTech Connect

    Li, Y.; Xu, Z.

    1997-12-31

    This paper presents the coal slime slurry combustion technology in circulating fluidized bed (CFB) boilers. The technique is that the slurry-based flow from the concentrator in the coal washery plant directly feeds into the fluidized bed by pump for combustion after a simple filtration and enrichment to an approximate concentration of 50% of coal. The coal slime slurry can burn in a CFB boiler alone or jointly with coal refuse. The technique has been used in a 35 t/h (6MWe) CFB for power generation. The result shows that the combustion efficiency is over 96% and boiler thermal efficiency is over 77%. As compared with burning coal refuse alone, the thermal efficiency was improved by 3--4 percent. This technology is simple, easy to operate and reliable. It is an effective way to utilize coal slime slurry. It has a practical significance for saving coal resources and reducing environmental pollution near coal mine areas. As a clean coal technology, it will result in great social, environmental and economic benefits.

  12. Rheological characterization of hydraulic fracturing slurries

    SciTech Connect

    Shah, S.N. . Research and Engineering Dept.)

    1993-05-01

    Few studies have dealt with the flow behavior of concentrated suspensions or slurries prepared with non-Newtonian carrier fluids. Therefore, the purpose of this investigation is to present experimental results obtained by pumping various hydraulic fracturing slurries into a fracture model and gathering data on differential pressure vs. flow rate. Several concentrations of hydroxypropyl guard (HPG), a wide range of proppant concentrations, and three test temperatures were studies. The effects of such variables as polymer gelling-agent concentration, proppant concentration, test temperature, and fracture-flow shear rate on the rheological properties of slurries were investigated. The correlations for predicting the relative slurry viscosity for these HPG fluids are presented. Substantial increases in viscosity of fracturing gels were observed, and results are discussed in light of several affecting variables. Results also are compared with those available for Newtonian and non-Newtonian concentrated suspensions. Applications of these correlations to estimate the hindered particle-settling velocity in the fracture caused by the presence of surrounding particles also is discussed. The correlations presented can easily be included in any currently available 2D or 3D fracture-design simulators; thus, the information can be applied directly to predict fracture geometry and extension.

  13. Remediation of Cr(VI)-Contaminated Soil Using the Acidified Hydrazine Hydrate.

    PubMed

    Ma, Yameng; Li, Fangfang; Jiang, Yuling; Yang, Weihua; Lv, Lv; Xue, Haotian; Wang, Yangyang

    2016-09-01

    Acidified hydrazine hydrate was used to remediate Cr(VI)-contaminated soil. The content of water-soluble Cr(VI) in contaminated soil was 4977.53 mg/kg. The optimal initial pH of hydrazine hydrate solution, soil to solution ratio and molar ratio of Cr(VI) to hydrazine hydrate for remediation of Cr(VI)-contaminated soil were 5.0, 3:1 and 1:3, respectively. Over 99.50 % of water-soluble Cr(VI) in the contaminated soil was reduced at the optimal condition within 30 min. The remediated soil can keep stable within 4 months. Meanwhile the total phosphorus increased from 0.47 to 4.29 g/kg, indicating that using of acidified hydrazine hydrate is an effective method to remediate Cr(VI)-contaminated soil.

  14. Method and centrifugal apparatus for slurry testing

    SciTech Connect

    Tuzson, J.J.

    1984-04-17

    In accordance with the centrifugal erosion testing method of the invention, a material specimen is rotated with a flat surface facing the direction of rotation and a narrow stream of an abrasive particle slurry is concurrently flowed at a preselected rate in a radial direction across the flat surface, the rotating step being at sufficiently high angular velocity to urge the abrasive particles by Coriolis acceleration into a compacted mass against the flat surface and erode material therefrom by scouring type action as the particles flow radially outward. The rotating and flowing steps are continued for a sufficient preselected duration to erode material to a measurable depth, and the depth to which the flat surface is worn by the abrasive particles is measured as an indication of the erosion resistance of the specimen material. The centrifugal slurry erosion testing apparatus includes a rotatable cylindrical vessel into the interior of which the abrasive slurry is fed and a specimen holder extending radially from the vessel having a cavity for receiving the specimen and a radial slurry flow passage communicating with the interior of the vessel. One of the radial passage longitudinal walls is defined by the flat surface of the specimen. Preferably the specimen holder comprises mating semicylindrical halves one of which has a specimen-receiving cavity in its abutting surface and the other has a narrow rectangular-in-cross section groove in its abutting surface which communicates with the interior of the vessel and together with the flat surface of the specimen defines the radial slurry flow passage. The mating semicylindrical halves are enclosed by a sleeve having an annular rim disposed interiorly of the vessel to prevent radially outward movement of the specimen holder.

  15. EOS for critical slurry and solution systems

    SciTech Connect

    DiPeso, G; Peterson, P

    1998-10-27

    In a fire involving fissile material, the mixture of the fissile material ash with fire fighting water may lead to a criticality excursion if there are nearby sumps that permit a critical geometry. The severity of the resulting energy release and pressure pulse is dependent on the rate at which the mixing occurs. To calculate these excursions, a non-equilibrium equation of state for the water ash mixture or slurry is needed that accounts for the thermal non-equilibrium that occurs due to finite heat transfer rates. We are developing the slurry EOS as well as a lumped neutronic and hydrodynamic model to serve as a testing ground for the non-equilibrium EOS before its incorporation into more sophisticated neutronic-hydrodynamics codes. Though the model lacks spatial dependence, it provides estimates of energy release and pressure pulses for various mixture assembly rates. We are also developing a non-equilibrium EOS for critical solution systems in which the fissile material is dissolved in water, which accounts for chemical non-equilibrium due to finite mass transfer rates. In contrast to previously published solution EOS, our solution EOS specifically accounts for mass diffusion of dissolved radiolytic gas to bubble nucleation sites. This EOS was developed to check our overall modeling against published solution excursion experiments and to compare solution excursions with slurry excursions initiated under the same conditions. Preliminary results indicate a good match between solution EOS calculations and experiments involving premixed 60-80 g U/l solutions for both low rate and high rate reactivity insertions. Comparison between slurry and solution calculations for the same composition show comparable energy release and pressure peaks for both low and high rate reactivity insertions with the slurry releasing less energy but generating more pressure than the solution for the amount of energy released. Calculations more appropriate to actual fire fighting scenarios

  16. Slurry sampling graphite furnace atomic absorption spectrometry: a preliminary examination of results from an international collaborative study

    NASA Astrophysics Data System (ADS)

    Miller-Ihli, N. J.

    1995-06-01

    An international collaborative study was initiated to evaluate the current state-of-the-art for solid sampling. Samples were sent to 28 laboratories and data were received from 18 collaborators, 16 of which reported slurry results. A preliminary check of performance using NIST SRM 1643c acidified water, showed that at least 13 laboratories were able to provide accurate results within ±10% of the mean certified Pb and Cr concentrations. The focus of this work was slurry analytical data reported by collaborators. Average performance by collaborators for the determination of Pb in NIST SRM 2704 Buffalo River Sediment was 103% recovery based on the mean certified reference value and was 84% recovery based on the mean certified reference value for NRCC PACS-1, a marine estuarine sediment, which was identified to collaborators as an unknown sediment. Average performance by collaborators for Cr in SRM 2704 was 96% based on the mean certified reference value and was 78% recovery based on the mean certified reference value for PACS-1. The use of secondary wavelengths and the importance of analysis of a representative subsample are highlighted. Possible problems leading to inaccurate results being reported by collaborators are discussed including the use of mini-flows, matrix modifiers, low atomization temperatures, short atomization times, and expulsion losses.

  17. Evaluation of slurry characteristics for rechargeable lithium-ion batteries

    SciTech Connect

    Cho, Ki Yeon; Kwon, Young Il; Youn, Jae Ryoun; Song, Young Seok

    2013-08-01

    Graphical abstract: - Highlights: • Lithium-ion battery slurries are prepared for rechargeable batteries. • The dispersion state of slurry constituents is identified. • Thermal, morphological, rheological, and electrical properties of slurries are analyzed. - Abstract: A multi-component slurry for rechargeable batteries is prepared by dispersing LiCoO{sub 2}, conductive additives, and polymeric binders in a solvent. The physical properties, including rheological, morphological, electrical, and spectroscopic features of battery slurries are investigated. The relationship between the measured physical properties and the internal structure of the slurry is analyzed. It is found that the rheological behavior of the slurry is determined by the interaction of active materials and binding materials (e.g., network structure) and that the dispersion state of conductive additives (e.g., agglomeration) also depends on the binder–carbon interaction.

  18. Determination of 5-log pathogen reduction times for heat-processed, acidified vegetable brines.

    PubMed

    Breidt, F; Hayes, J S; Osborne, J A; McFeeters, R F

    2005-02-01

    Recent outbreaks of acid-resistant food pathogens in acid foods, including apple cider and orange juice, have raised concerns about the safety of acidified vegetable products. We determined pasteurization times and temperatures needed to assure a 5-log reduction in the numbers of Escherichia coli O157:H7, Listeria monocytogenes, and Salmonella strains in acidified cucumber pickle brines. Cocktails of five strains of each pathogen were (separately) used for heat-inactivation studies between 50 and 60 degrees C in brines that had an equilibrated pH value of 4.1. Salmonella strains were found to be less heat resistant than E. coli O157:H7 or L. monocytogenes strains. The nonlinear killing curves generated during these studies were modeled using a Weibull function. We found no significant difference in the heat-killing data for E. coli O157:H7 and L. monocytogenes (P = 0.9709). The predicted 5-log reduction times for E. coli O157:H7 and L. monocytogenes were found to fit an exponential decay function. These data were used to estimate minimum pasteurization times and temperatures needed to ensure safe processing of acidified pickle products and show that current industry pasteurization practices offer a significant margin of safety.

  19. Relative acidifying activity of anionic salts commonly used to prevent milk fever.

    PubMed

    Goff, J P; Ruiz, R; Horst, R L

    2004-05-01

    High cation diets can cause milk fever in dairy cows as they induce a metabolic alkalosis reducing the ability of the cow to maintain calcium homeostasis at the onset of lactation. Adding anions to the diet can offset the effect of the high cation forages by inducing a mild metabolic acidosis, restoring the ability to maintain calcium homeostasis. The difference in mEq of dietary cations and anions (DCAD) is most often expressed as (Na(+) + K+) - (Cl- + S(--)). This equation implies that a mEq of chloride and a mEq of sulfate are equipotent in their ability to alter acid-base balance of the cow. Using blood and urine pH to monitor effects on acid-base balance, experiments were conducted to test the relative acidifying activity of various sulfate and chloride anion sources in nonpregnant, nonlactating Jersey cows. Across all experiments, chloride proved to have about 1.6 times the acidifying activity of sulfate. Calcium and magnesium, ignored by the common DCAD equation, had a small but significant alkalinizing effect when accompanying chloride or sulfate. The ranking of the anion sources tested at a dose of 2 Eq/d, from most to least potent urine acidifier, was hydrochloric acid, ammonium chloride, calcium chloride, calcium sulfate, magnesium sulfate, and sulfur. These data should allow more accurate prediction of the response of late gestation cows to dietary cation-anion manipulation.

  20. System for pressure letdown of abrasive slurries

    DOEpatents

    Kasper, Stanley

    1991-01-01

    A system and method for releasing erosive slurries from containment at high pressure without subjecting valves to highly erosive slurry flow. The system includes a pressure letdown tank disposed below the high-pressure tank, the two tanks being connected by a valved line communicating the gas phases and a line having a valve and choke for a transfer of liquid into the letdown tank. The letdown tank has a valved gas vent and a valved outlet line for release of liquid. In operation, the gas transfer line is opened to equalize pressure between tanks so that a low level of liquid flow occurs. The letdown tank is then vented, creating a high-pressure differential between the tanks. At this point, flow between tanks is controlled by the choke. High-velocity, erosive flow through a high-pressure outlet valve is prevented by equalizing the start up pressure and thereafter limiting flow with the choke.

  1. Stabilized water slurries of carbonaceous materials

    SciTech Connect

    Papalos, J.G.; Knitter, K.A.; Savoly, A.; Villa, J.L.

    1984-07-03

    Improved stabilized water slurries of carbonaceous materials are obtained by having present a condensation product or a salt thereof of a substituted phenol sulfonic acid which is an arylphenol sulfonic acid, an aralkylphenol sulfonic acid, an arylphenol sulfonic acid and arylsulfonic acid mixture, or an aralkylphenol sulfonic acid and arylsulfonic acid mixture, condensed with from about 0.5 to about 4.0 moles of formaldehyde per mole of sulfonic acid with the proviso that the weight ratio if substituted phenol sulfonic acid to arylsulfonic acid is from about 0.95:0.05 to about 0.05:0.95 in the mixtures, the condensation product being present in an amount sufficient to reduce viscosity of the water slurry of carbonaceous materials, to stabilize carbonaceous materials in the water network and to improve its pumpability. If desired, an acid form or a salt of the condensation product may be used.

  2. Carbon Slurry Fuels for Volume Limited Missiles

    DTIC Science & Technology

    1979-11-01

    carbon slurry fuel combustion is to be understood. Major aspects of hydrocarbon combustion chemistry involve hydrocarbon pyroly - sis and partial oxidation...effective convcr•ei)n ’)i thiv pyroly - sis product to carbon particulate. 207 cyclo Hxmne 0 5.1 0.1.0 2.0 271 ’I 20 / i 0 6 10 15 20 Ŕ cyclo Hexene n" \\C

  3. Fischer-Tropsch Slurry Reactor modeling

    SciTech Connect

    Soong, Y.; Gamwo, I.K.; Harke, F.W.

    1995-12-31

    This paper reports experimental and theoretical results on hydrodynamic studies. The experiments were conducted in a hot-pressurized Slurry-Bubble Column Reactor (SBCR). It includes experimental results of Drakeol-10 oil/nitrogen/glass beads hydrodynamic study and the development of an ultrasonic technique for measuring solids concentration. A model to describe the flow behavior in reactors was developed. The hydrodynamic properties in a 10.16 cm diameter bubble column with a perforated-plate gas distributor were studied at pressures ranging from 0.1 to 1.36 MPa, and at temperatures from 20 to 200{degrees}C, using a dual hot-wire probe with nitrogen, glass beads, and Drakeol-10 oil as the gas, solid, and liquid phase, respectively. It was found that the addition of 20 oil wt% glass beads in the system has a slight effect on the average gas holdup and bubble size. A well-posed three-dimensional model for bed dynamics was developed from an ill-posed model. The new model has computed solid holdup distributions consistent with experimental observations with no artificial {open_quotes}fountain{close_quotes} as predicted by the earlier model. The model can be applied to a variety of multiphase flows of practical interest. An ultrasonic technique is being developed to measure solids concentration in a three-phase slurry reactor. Preliminary measurements have been made on slurries consisting of molten paraffin wax, glass beads, and nitrogen bubbles at 180 {degrees}C and 0.1 MPa. The data show that both the sound speed and attenuation are well-defined functions of both the solid and gas concentrations in the slurries. The results suggest possibilities to directly measure solids concentration during the operation of an autoclave reactor containing molten wax.

  4. Metal Slurry Droplet and Spray Combustion

    DTIC Science & Technology

    1993-09-15

    Thermophoresis on the Oxide Condensation 156 ii Appendix E Numerical Modeling of a Slurry Droplet Containing a Spherical Particle...Williams [110]. Thermophoresis can cause the condensed particles to move outwards, from the radius of condensation. However, convection would drive the...Here, the thermophoresis effect may drive the condensed particles outwards. However, since the bulk flow in the outer zone is negative (towards the

  5. Abrasive slurry composition for machining boron carbide

    DOEpatents

    Duran, E.L.

    1984-11-29

    An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

  6. Abrasive slurry composition for machining boron carbide

    DOEpatents

    Duran, Edward L.

    1985-01-01

    An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

  7. Slaughterfloor decontamination of pork carcases with hot water or acidified sodium chlorite - a comparison in two Australian abattoirs.

    PubMed

    Hamilton, D; Holds, G; Lorimer, M; Kiermeier, A; Kidd, C; Slade, J; Pointon, A

    2010-11-01

    A decontamination trial on the effectiveness of hot water or acidified sodium chlorite (SANOVA) treatment on Salmonella spp., Escherichia coli and Total Viable Count (TVC) was undertaken on pork carcases prior to primary chilling in two large pork abattoirs in Australia using belly-strip excision sampling. A total of 123 samples from Abattoir A and 400 samples from Abattoir B were cultured and analysed. Test pigs were selected from herds with a known high level of on-farm Salmonella infection. At Abattoir A, Salmonella spp. were not isolated from carcases. The prevalence of E. coli on control carcases was 92.9% compared with 9.8% for hot water and 12.5% for SANOVA treated carcases. The mean log(10) E. coli concentration for control carcases was 0.89 cfu/gram, compared with -0.83 cfu/gram from hot water and -0.75 cfu/gram from SANOVA treated carcases. The mean log(10) TVC for control carcases was 4.06 compared with 1.81 cfu/gram for hot water and 2.76 cfu/gram for SANOVA treated carcases. At Abattoir B, the prevalence of Salmonella on control carcases was 16% compared with 2.7% for hot water and 7.0% for SANOVA treated carcases. The prevalence of E. coli on control carcases was 69.3% compared with 22% for hot water and 30% for SANOVA treated carcases. The mean log(10) E. coli concentration for control carcases was 0.45 cfu/gram, compared with -0.65 cfu/gram from hot water and -0.60 cfu/gram from SANOVA treated carcases. The mean log(10) TVC for control carcases was 3.00 cfu/gram compared with 2.10 cfu/gram for hot water and 2.53 cfu/gram for SANOVA treated carcases. The reductions in prevalence and mean log(10) concentrations in the present trial were all found to be statistically significant and indicate that carcases decontamination with either hot water or SANOVA are effective risk management options immediately available to the pork industry.

  8. Effect of liquid feeding weaned pigs on growth performance to harvest.

    PubMed

    Lawlor, P G; Lynch, P B; Gardiner, G E; Caffrey, P J; O'Doherty, J V

    2002-07-01

    Four experiments were undertaken to examine the effect of feeding postweaning diets as dry pelleted feed, fresh liquid feed, acidified liquid feed, and fermented liquid feed on pig performance from weaning (26 d) to harvest. In Exp. 1 (n = 12 replicates) and 2 (n = 10 replicates), the treatments were 1) dry pelleted feed and 2) fresh liquid feed. In Exp. 1, 2 kg of starter diet (16.7 MJ of DE/kg and 1.6% lysine) per pig and 5 kg of transition diet (16.7 MJ of DE/kg and 1.5% lysine) per pig followed by a weaner diet (14.0 MJ of DE/kg and 1.36% lysine) were offered to 27 d after weaning. In Exp. 3 (n = 8 replicates), the treatments were 1) dry pelleted feed, 2) fresh liquid feed, and 3) acidified liquid feed. In Exp. 4 (n = 8 replicates), the treatments were 1) dry pelleted feed, 2) acidified liquid feed, and 3) fermented liquid feed. In Exp. 2, 3, and 4, 3 kg of starter diet (16.1 MJ of DE/kg and 1.74% lysine) per pig and 6 kg of transition diet (15.3 MJ of DE/kg and 1.5% lysine) per pig followed by a weaner diet (14.0 MJ of DE/kg and 1.36% lysine) was offered to 27 d after weaning. All treatments were balanced for boars and gilts and diets were offered for ad libitum consumption. Acidified liquid feed was produced by adding lactic acid to the liquid feed so that its pH was decreased to 4.0. Fermented liquid feed was produced by adding an inoculum of Lactococcus lactis subsp. cremoris 303 (1.3%, vol/wt) to the first mix. In Exp. 1, ADG from weaning to d 27 after weaning was 338 and 286 g/d (SEM = 10; P < 0.01) and DM gain/feed in the same period was 888 and 594 g/kg (SEM = 23.1; P < 0.001) for dry pelleted feed and fresh liquid feed, respectively. In Exp. 2, ADG was 391 and 352 g/d (SEM = 6.4; P < 0.01) and DM gain/feed was 856 and 642 g/kg (SEM = 9.9; P < 0.001) for dry pelleted feed and fresh liquid feed, respectively, during the period from weaning to d 27 after weaning. In Exp. 3, ADG was 408, 416, and 433 g/d (SEM = 12.7; P > 0.05) and DM gain/feed was 865, 755

  9. Biodegradation of Pig Manure by the Housefly, Musca domestica: A Viable Ecological Strategy for Pig Manure Management

    PubMed Central

    Čičková, Helena; Pastor, Berta; Kozánek, Milan; Martínez-Sánchez, Anabel; Rojo, Santos; Takáč, Peter

    2012-01-01

    The technology for biodegradation of pig manure by using houseflies in a pilot plant capable of processing 500–700 kg of pig manure per week is described. A single adult cage loaded with 25,000 pupae produced 177.7±32.0 ml of eggs in a 15-day egg-collection period. With an inoculation ratio of 0.4–1.0 ml eggs/kg of manure, the amount of eggs produced by a single cage can suffice for the biodegradation of 178–444 kg of manure. Larval development varied among four different types of pig manure (centrifuged slurry, fresh manure, manure with sawdust, manure without sawdust). Larval survival ranged from 46.9±2.1%, in manure without sawdust, to 76.8±11.9% in centrifuged slurry. Larval development took 6–11 days, depending on the manure type. Processing of 1 kg of wet manure produced 43.9–74.3 g of housefly pupae and the weight of the residue after biodegradation decreased to 0.18–0.65 kg, with marked differences among manure types. Recommendations for the operation of industrial-scale biodegradation facilities are presented and discussed. PMID:22431982

  10. Geotechnical properties of debris-flow sediments and slurries

    USGS Publications Warehouse

    Major, J.J.; Iverson, R.M.; McTigue, D.F.; Macias, S.; Fiedorowicz, B.K.

    1997-01-01

    Measurements of geotechnical properties of various poorly sorted debris-flow sediments and slurries (??? 32 mm diameter) emphasize their granular nature, and reveal that properties of slurries can differ significantly from those of compacted sediments. Measurements show that: (1) cohesion probably offers little resistance to shear in most debris flows under low confining stresses normally found in nature; (2) intrinsic hydraulic permeabilities of compacted debris-flow sediments vary from about 10-14-10-9 m2; permeabilities of 'typical' debris-flow slurries fall toward the low end of the range; (3) debris-flow slurries are characterized by very large values of 'elastic' compressibility (C approx. 10-2 kPa-1); and (4) hydraulic diffusivities of quasistatically consolidating slurries are approx. 10-4-10-7 m2/s. Low hydraulic diffusivity of debris slurries permits excess fluid pressure and low effective strength to persist during sediment transport and deposition.

  11. Fresh and preserved green fodder modify effects of urinary acidifiers on urine pH of horses.

    PubMed

    Goren, G; Fritz, J; Dillitzer, N; Hipp, B; Kienzle, E

    2014-04-01

    Hay stabilises urine pH in horses. It is unknown whether this is an effect of structure or of chemical composition. In this study, four ponies (230-384 kg body weight [BW]) were fed six different diets with either a structure or a composition similar to hay with and without acidifiers in a cross-over experimental design in amounts to maintain body weight with the following main compounds: Fresh grass (GRASS), alfalfa hay (ALF), grass cobs (COBS), grass silage (SIL), straw (STR) or extruded straw (STRe) for 2 to 10 days. Urine pH was measured in all trials, blood pH, blood base excess and bicarbonate as well as mineral balance were determined in GRASS, ALF, STR and STRe. In the trials with straw and extruded straw, urine pH decreased significantly (STR control: 7.8 ± 0.23, acidifier: 5.2 ± 0.38) when acidifiers were added, whereas in all other diets that were based on fresh or preserved green fodder, pH did not decrease below 7. Blood pH was similarly affected by diet and acidifiers. Acidifiers had little effect on the pre-prandial blood pH, only in diet STR there was a significant reduction in relation to control. Post-prandial blood pH was significantly reduced by acidifiers in all diets. Blood bicarbonate and base excess showed corresponding effects. Faecal and renal mineral excretion and apparent mineral digestibility were not systematically affected by diet or acidifiers except for chloride. Chloride added as inorganic chloride salt had an even better apparent digestibility than chloride originating from feed. Because only green plant material stabilised acid base balance, chlorophyll and its metabolites are discussed as potential mediators of the effect of green fodder on acid base balance.

  12. Methods to enhance the characteristics of hydrothermally prepared slurry fuels

    DOEpatents

    Anderson, Chris M.; Musich, Mark A.; Mann, Michael D.; DeWall, Raymond A.; Richter, John J.; Potas, Todd A.; Willson, Warrack G.

    2000-01-01

    Methods for enhancing the flow behavior and stability of hydrothermally treated slurry fuels. A mechanical high-shear dispersion and homogenization device is used to shear the slurry fuel. Other improvements include blending the carbonaceous material with a form of coal to reduce or eliminate the flocculation of the slurry, and maintaining the temperature of the hydrothermal treatment between approximately 300.degree. to 350.degree. C.

  13. Survey of state water laws affecting coal slurry pipeline development

    SciTech Connect

    Rogozen, M.B.

    1980-11-01

    This report summarizes state water laws likely to affect the development of coal slurry pipelines. It was prepared as part of a project to analyze environmental issues related to energy transportation systems. Coal slurry pipelines have been proposed as a means to expand the existing transportation system to handle the increasing coal shipments that will be required in the future. The availability of water for use in coal slurry systems in the coal-producing states is an issue of major concern.

  14. Partitioning and bioavailability of mercury in an experimentally acidified Wisconsin lake

    USGS Publications Warehouse

    Wiener, James G.; Fitzgerald, William F.; Watras, Carl J.; Rada, Ronald G.

    1990-01-01

    We studied the partitioning of mercury (Hg) among air, water, sediments and fish at Little Rock Lake, a clear water seepage lake in north-central Wisconsin. The lake was divided with a sea curtain into two basins, one acidified with sulfuric acid to pH 5.6 for two years and the other an untreated reference site (mean pH 6.1), to document the effects of acidification. Trace-metal-free protocols were used to measure Hg at the picomolar level in air and water. Total gaseous Hg in air samples averaged 2.0 ng/m3. Total Hg in unfiltered water samples collected in 1986 after the fall overturn averaged about 1 ng/L in the acidified and reference basins. Mercury in surficial sediments was strongly correlated with volatile matter content and ranged from 10 to about 170 ng/g (dry weight) in both basins. Total Hg concentrations in whole, calendar age-1 yellow perch (Perca flavescens), sampled after one year of residence in the lake, averaged 114 ng/g (fresh weight) in the reference basin and 135 ng/g in the acidified basin – a highly significant (p < 0.01) difference. The mean whole-body burden (quantity) of Hg in age-1 perch did not differ between basins after the first year, but was significantly greater in the treatment basin than in the reference basin after the second year of acidification. Differences between the two basins in the bioaccumulation of Hg were attributed to internal (within-lake) processes that influence the bioavailability of the metal. An initial Hg budget for the treatment basin of Little Rock Lake showed that atmospheric deposition and sedimentary remobilization of Hg are potentially important processes influencing its biogeochemical cycling and uptake by fish.

  15. Metal accumulation and metallothionein concentrations in tree swallow nestlings near acidified lakes

    SciTech Connect

    St. Louis, V.; Breebaart, L. . Dept. of Zoology); Barlow, J.C. . Dept. of Zoology Royal Ontario Museum, Toronto, Ontario . Dept. of Ornithology); Klaverkamp, J.F. . Dept. of Fisheries and Oceans)

    1993-07-01

    The authors studied metal accumulation in hepatic and renal tissues of tree swallow (Tachycineta bicolor) nestlings at acidified and nonacid reference lakes in northwestern Ontario. Hepatic concentrations of metallothionein (metal-binding proteins, MT) in tree swallow nestlings were negatively correlated with pH of the nest-site lake. Combined concentrations of Cu and Zn in the liver were correlated with liver MT concentrations, but Cd was not. Although no overt signs of metal toxicity were observed in nestlings near acid lakes, the results clearly provided evidence that metals are transferred from acid lakes to birds and that these metals are correlated with increases in hepatic MT production.

  16. The effect of sucrose on unfrozen water and syneresis of acidified sodium caseinate-xanthan gels.

    PubMed

    Braga, A L M; Cunha, R L

    2005-07-01

    The influence of the ingredients of acidified Na caseinate-xanthan-sucrose gels on thermophysical properties and syneresis of the gels was studied. Sucrose concentration affected all of the gel equilibrium properties and the rate of syneresis. The positive effect of sucrose on syneresis and unfrozen water (UFW) values was attributed to different effects. The amount of UFW was governed mainly by the colligative properties of sucrose whereas the equilibrium syneresis behaviour was associated with the changes in network dynamics caused by the kosmotropic properties of sucrose. The latter could enhance xanthan-sucrose association or favour xanthan-protein interactions.

  17. Evaluation of sodium bisulphate and phosphoric acid as urine acidifiers for cats.

    PubMed

    Spears, Julie K; Grieshop, Christine M; Fahey, G C

    2003-10-01

    Eighteen cats were used to compare the urine acidifying properties of sodium bisulphate to phosphoric acid. Acidifying agents were added at one of three concentrations (0.4, 0.6, or 0.8%, as-is basis). Cats were offered a commercial diet to determine basal urinary pH, and then again for a 1 week period between blocks 1 and 2. Cats were acclimated to the diets for 6 days, and urine samples were collected on day 7 at 0, 4, and 8 h postfeeding to obtain pre- and postprandial urinary pH. Intakes of diets containing sodium bisulphate tended (P < 0.07) to be lower than intakes of diets containing phosphoric acid. Cats consuming the 0.8% phosphoric acid diet had higher (P < 0.05) food intakes than cats consuming either the 0.4 or 0.6% phosphoric acid-containing diets. There was significant (P = 0.01) linear and quadratic response for food intake in cats consuming the sodium bisulphate-containing diet. Cats consuming the 0.4 and 0.8% phosphoric acid-containing diets tended (P = 0.07) to have higher water intakes than cats consuming the 0.6% phosphoric acid-containing diet. There were no differences (P > 0.05) in urine pH and specific gravity between cats fed the different acidifier types. Cats consuming the 0.6% phosphoric acid-containing diet tended (P = 0.07) to have a higher urine pH 8 h post-feeding than cats consuming the 0.4 and 0.8% phosphoric acid-containing diets. Urine pH was highest at 4 h post-feeding except for cats fed the 0.4% sodium bisulphate- and the 0.6% phosphoric acid-containing diets. No differences (P > 0.05) between acidifiers were found in faecal score or in faecal dry matter and organic matter concentrations. A quadratic response was detected in faecal score for cats consuming the phosphoric acid-containing diets. Cats consuming the 0.6% phosphoric acid diet tended (P = 0.06) to have a lower faecal score than cats consuming the 0.4 and 0.8% phosphoric acid diets. For faecal dry matter, a linear trend was detected in cats consuming the sodium

  18. Ice slurry cooling research: Storage tank ice agglomeration and extraction

    SciTech Connect

    Kasza, K.; Hayashi, Kanetoshi

    1999-08-01

    A new facility has been built to conduct research and development on important issues related to implementing ice slurry cooling technology. Ongoing studies are generating important information on the factors that influence ice particle agglomeration in ice slurry storage tanks. The studies are also addressing the development of methods to minimize and monitor agglomeration and improve the efficiency and controllability of tank extraction of slurry for distribution to cooling loads. These engineering issues impede the utilization of the ice slurry cooling concept that has been under development by various groups.

  19. Slurry Supplying Method for Large Quartz Glass Substrate Polishing

    NASA Astrophysics Data System (ADS)

    Khajornrungruang, Panart; Kimura, Keiichi; Yui, Ryuji; Wada, Nagisa; Suzuki, Keisuke

    2011-05-01

    Chemical mechanical polishing (CMP) has been used in polishing a photomask substrate in flat-panel display (FPD) manufacture. Moreover, the quadrilateral geometry of quartz glass used as the photomask substrate has been enlarged. However, the slurry cannot flow throughout the glass surface evenly owing to the enlarged substrate covering the center of the platen in the polishing process. In this work, we verified the beneficial of spreading slurry into a non-inflow region by the reinforced suction of the slurry supplied to the polishing pad through a hole at center of the platen. A fluorescent agent was used instead of the slurry for flow visualization.

  20. Oxidation of coal-water slurry feed to hydrogasifier

    DOEpatents

    Lee, Bernard S.

    1976-01-01

    An aqueous coal slurry is preheated, subjected to partial oxidation and vaporization by injection of high pressure oxygen and is introduced into a top section of a hydrogasifier in direct contact with hot methane-containing effluent gases where vaporization of the slurry is completed. The resulting solids are reacted in the hydrogasifier and the combined gases and vapors are withdrawn and subjected to purification and methanation to provide pipeline gas. The amount of oxygen injected into the slurry is controlled to provide the proper thermal balance whereby all of the water in the slurry can be evaporated in contact with the hot effluent gases from the hydrogasifier.

  1. The influence of additives on rheological properties of limestone slurry

    NASA Astrophysics Data System (ADS)

    Jaworska, B.; Bartosik, A.

    2014-08-01

    Limestone slurry appears in the lime production process as the result of rinsing the processed material. It consists of particles with diameter smaller than 2 mm and the water that is a carrier of solid fraction. Slurry is directed to the settling tank, where the solid phase sediments and the excess water through the transfer system is recovered for re-circulation. Collected at the bottom of the tank sludge is deposited in a landfill located on the premises. Rheological properties of limestone slurry hinder its further free transport in the pipeline due to generated flow resistance. To improve this state of affairs, chemical treatment of drilling fluid, could be applied, of which the main task is to give the slurry properties suitable for the conditions encountered in hydrotransport. This treatment consists of applying chemical additives to slurry in sufficient quantity. Such additives are called as deflocculants or thinners or dispersants, and are chemical compounds which added to aqueous solution are intended to push away suspended particles from each other. The paper presents the results of research allowing reduction of shear stress in limestone slurry. Results demonstrate rheological properties of limestone slurry with and without the addition of modified substances which causes decrease of slurry viscosity, and as a consequence slurry shear stress for adopted shear rate. Achieving the desired effects increases the degree of dispersion of the solid phase suspended in the carrier liquid and improving its ability to smooth flow with decreased friction.

  2. Combinatorial study of ceramic tape-casting slurries.

    PubMed

    Liu, Zhifu; Wang, Yiling; Li, Yongxiang

    2012-03-12

    Ceramic tape-casting slurries are complex systems composed of ceramic powder, solvent, and a number of organic components. Conventionally, the development of ceramic tape-casting slurries is time-consuming and of low efficiency. In this work, combinatorial approaches were applied to screen the ethanol and ethyl-acetate binary solvent based slurry for ceramic green tape-casting. The combinatorial libraries were designed considering the variation of the amount of PVB (Poly vinyl-butyral) binder, polyethylene-400, and butyl-benzyl-phthalate plasticizers, and glyceryl triacetate dispersant. A parallel magnetic stirring process was used to make the combinatorial slurry library. The properties mapping of the slurry library was obtained by investigating the sedimentation and rheological characteristics of the slurries. The slurry composition was refined by scaling up the experiments and comparing the microstructure, mechanical property, and sintering behavior of green tapes made from the selected slurries. Finally, a kind of ethanol-ethyl acetate binary solvent based slurry system suitable for making X7R dielectric ceramic green tapes was achieved.

  3. Ice slurry cooling research: Microscale study of ice particles characteristics, role of freezing point depressant, and influence on slurry fluidity

    SciTech Connect

    Hayashi, K.; Kasza, K.

    2000-05-03

    The influences of freezing-point-depressants on ice slurry characteristics in the form of ice slurry fluidity and on the microscale ice particle features are studied. The results identify microscale features of ice particles such as surface roughness that greatly influence slurry fluidity that are altered favorably by the use of a freezing point depressant. The engineering of a workable and efficient ice slurry cooling system depends very strongly on the characteristics of the individual ice particles in the slurry and, in turn, on the method of ice production. Findings from this study provide guidance on the fluidity and handleability of slurry produced by several methods currently under development and already many achieved.

  4. Transgenesis for pig models

    PubMed Central

    Yum, Soo-Young; Yoon, Ki-Young; Lee, Choong-Il; Lee, Byeong-Chun

    2016-01-01

    Animal models, particularly pigs, have come to play an important role in translational biomedical research. There have been many pig models with genetically modifications via somatic cell nuclear transfer (SCNT). However, because most transgenic pigs have been produced by random integration to date, the necessity for more exact gene-mutated models using recombinase based conditional gene expression like mice has been raised. Currently, advanced genome-editing technologies enable us to generate specific gene-deleted and -inserted pig models. In the future, the development of pig models with gene editing technologies could be a valuable resource for biomedical research. PMID:27030199

  5. Mn2O3 Slurry Reuse by Circulation Achieving High Constant Removal Rate

    NASA Astrophysics Data System (ADS)

    Kishii, Sadahiro; Nakamura, Ko; Hanawa, Kenzo; Watanabe, Satoru; Arimoto, Yoshihiro; Kurokawa, Syuhei; Doi, Toshiro K.

    2012-04-01

    Fumed silica is widely used in SiO2 chemical mechanical polishing (CMP). In semiconductor processes, only fresh slurry is used, and used slurry is disposed. Sustainable development demands a reduction in waste. Since reuse of slurry is effective for reducing the amount of used slurry generated, we investigated the reuse of Mn2O3 slurry and conventional fumed silica slurry. In both cases, abrasive concentration decreases as reuse time increases. The removal rate for Mn2O3 slurry maintains a value 4 times that of the conventional fumed silica slurry during slurry reuse, because the removal rate for Mn2O3 slurry is almost constant for solid concentrations between 1.0 and 10 wt %. Pad conditioning was not performed for Mn2O3 slurry. The removal rate for conventional slurry decreases as the number of times of reuse increases, even when pad conditioning is appropriately performed.

  6. High pressure slurry pump. Sand slurry test loop design and results. Wear parts lifetime analysis

    SciTech Connect

    Fongaro, S.; Severini, P.; Vinciguerra, G.

    2000-07-01

    This paper shows the experimental phase, following previous work presented at the Sixth International Conference on ``Multiphase Flow in Industrial Plants'', Milan, September 98. A Sand Water Slurry Test Loop has been tested using different sand percentages for a total power of 680 HP with a flow-rate of 35,000 [gpm] and pressure of 2300 [psig]. Its design considered, carefully, the particles build-up effect respecting flow velocity and dead space along the loop and into the hydraulics. The test pump is a TRIPLEX SINGLE ACTING that is one third of the COAL SLURRY SEPTUPLEX PUMP designed for a CHINA PROJECT. Wear rate on the main parts of an high pressure slurry pump have been analyzed running at 145 rpm (piston mean speed of 3.3 [ft/s]) with a net flow of 33,290 [gpm] and pressures between 1216 and 1575 [psig]. Tests gave indications of a damaging process on valves, piston seals and the relative weight on the overall damages. Design changes of piston-seal and its material have been done, results being a longer parts lifetime. The authors compared the results with literature on coal slurry and other sand tests. The pump speed, i.e., valve cycle, isn't the main wear factor, while the fluid speed under the valve is. Their goals are to improve the wear parts lifetime and define functions to relate the wear to operating parameters, design choice, and materials used.

  7. Rheology of sludge-slurry grouts

    SciTech Connect

    McDaniel, E. W.

    1980-10-01

    A series of rheograms was developed that relates the critical velocity (velocity where flow changes from laminar to turbulent) of a cementitious grout that incorporates a suspended sludge-slurry to the critical velocity of a reference grout made with a simulated waste solution. The sludge that is now in the Gunite waste tanks at the Oak Ridge National Laboratory (ORNL) will be suspended and pumped to the new waste storage tanks in Melton Valley. The sludge will then be blended with a cement mix base to form a grout which will be injected underground by the shale fracturing process. This report describes the materials, equipment, and techniques used in the laboratory studies to suspend sludges and mix sludge-slurry grouts that have flow properties similar to those of current shale fracturing grouts. Bentonite clay is an effective suspender in dilute NaNO/sub 3/ solutions; 15 wt % solids can be suspended with 2.0 wt % bentonite in a 0.1 M NaNO/sub 3/ solution. Other suspending materials were evaluated, but bentonite gave the best results. If a slurry grout becomes too viscous to pump, methods must be available to thin the mixture. A number of thinners, friction reducers, and plasticizers were examined. Q-Broxin, a thinner supplied by Baroid, reduced the velocity of a grout required for turbulent flow in a 5.0-cm (2-in.)-diam tube from 1.76 to 1.20 m/s (5.79 to 3.95 ft/s); FX-32C, a plasticizer supplied by Fox Industries, Inc., reduced the velocity from 1.76 to 0.75 m/s (5.6 to 2.45 ft/s).

  8. Protozoan grazing on bacteria at the sediment-water interface of an acidified lake

    SciTech Connect

    Tremaine, S.C.

    1988-01-01

    Protozoan grazing on bacteria has been hypothesized to link the detrital and grazer food chains in aquatic ecosystems. The current study of protozoan bacterivory, evaluated methods, quantified bacterivory, and evaluated the role of protozoa at the sediment-water interface of an acidified lake ecosystem, Lake Anna, Virginia. Three limnetic methods for determining protozoan bacterivory were tested for applicability at the sediment-water interface. The eucaryote inhibitor, cycloheximide, was found unsatisfactory because it did not uniformly inhibit growth of target eucaryotes, and because it inhibited non-target anaerobic procaryotes. The filtration method was found to have limited application in sediment systems due to filtrational loss of particle-associated bacteria. The dilution method was tested for violations of its critical assumptions: bacterial growth is exponential; grazing mortality is proportional to the dilution factor; and bacterial growth rates are unaltered under experimental conditions. These assumptions were found not to be violated, and this method was used in subsequent grazing experiments. Carbon loading to the acidified arm of Lake Anna was 41 {times} 10{sup 6} g C {times} y{sup {minus}1}. This appears to be adequate carbon loading to support bacterial production and, in turn, protozoan bacterivory and production. Though there is no direct evidence that zooplankton graze on protozoa in this system, however, there is sufficient protozoan production to support an additional trophic level.

  9. Growth and physiological condition of black ducks reared on acidified wetlands

    USGS Publications Warehouse

    Rattner, B.A.; Haramis, G.M.; Chu, D.S.; Bunck, C.M.; Scanes, C.G.

    1987-01-01

    Acid deposition has been identified as one of several possible factors contributing to the decline of some waterfowl populations in North America. In an effort to examine the effects of acidification on black duck (Anas rubripes) recruitment, growth and physiological condition were monitored in ducklings foraging for a 10-day trial (days 10-20 of life) on acidified (pH 5.0) and : circumneutral (pH 6.8) fish-free emergent wetlands. Acidification of these wetlands suppressed phytoplankton and algal growth, and reduced invertebrate biomass. Ducklings maintained on acidified wetlands grew poorly compared with ducklings reared on circumneutral wetlands, as evidenced by lower final body weight and culmen and tarsus length. Plasma growth hormone concentration was elevated and triiodothyronine levels were lower in stunted ducklings, in part substantiating impairment of growth-regulating processes. Ducklings exhibiting poor growth tended to have lower hematocrit, lower plasma protein, glucose, and cholesterol concentrations, and higher uric acid levels, presumably reflecting alterations in metabolism and development due to inanition. These findings suggest that acid deposition may lower food production in wetlands and ultimately impair duckling growth, condition, and survival.

  10. Esterification of acidified oil with methanol by SPES/PES catalytic membrane.

    PubMed

    Shi, Wenying; He, Benqiao; Li, Jianxin

    2011-05-01

    A sulfonated polyethersulfone (SPES)/polyethersulfone (PES) blend catalytic membrane was prepared and used as a heterogeneous catalyst in the esterification of the acidified oil (acid value 153 mg KOH/g) with methanol for producing biodiesel. The results showed that the free fatty acids conversion reached 97.6% using SPES/PES catalytic membrane under the optimal esterification conditions. Meanwhile, the SPES/PES membrane with 20.3% degree of sulfonation showed a good catalytic stability. A pseudo-homogeneous kinetic model was established. The results indicated that the reaction rate constant increased with increasing methanol/acidified oil molar ratio, the loading of catalytic membrane and reaction temperature. The reaction order was 2 and the activation energy decreased from 74.65 to 21.07 kJ/mol with increasing catalytic membrane loading from 0 to 0.135 meq/g(oil). It implies that the esterification is not diffusively controlled but kinetically controlled. The predicted results were in good agreement with the experimental data.

  11. Spatial community shift from hard to soft corals in acidified water

    NASA Astrophysics Data System (ADS)

    Inoue, Shihori; Kayanne, Hajime; Yamamoto, Shoji; Kurihara, Haruko

    2013-07-01

    Anthropogenic increases in the partial pressure of CO2 (pCO2) cause ocean acidification, declining calcium carbonate saturation states, reduced coral reef calcification and changes in the compositions of marine communities. Most projected community changes due to ocean acidification describe transitions from hard coral to non-calcifying macroalgal communities; other organisms have received less attention, despite the biotic diversity of coral reef communities. We show that the spatial distributions of both hard and soft coral communities in volcanically acidified, semi-enclosed waters off Iwotorishima Island, Japan, are related to pCO2 levels. Hard corals are restricted to non-acidified low- pCO2 (225μatm) zones, dense populations of the soft coral Sarcophyton elegans dominate medium- pCO2 (831μatm) zones, and both hard and soft corals are absent from the highest- pCO2 (1,465μatm) zone. In CO2-enriched culture experiments, high- pCO2 conditions benefited Sarcophyton elegans by enhancing photosynthesis rates and did not affect light calcification, but dark decalcification (negative net calcification) increased with increasing pCO2. These results suggest that reef communities may shift from reef-building hard corals to non-reef-building soft corals under pCO2 levels (550-970μatm) predicted by the end of this century, and that higher pCO2 levels would challenge the survival of some reef organisms.

  12. [Decoloration of reactive turquoise blue by acidified sludge-bentonite granule].

    PubMed

    Yue, Qin-Yan; Yuan, Ai-Juan; Li, Qian; Gao, Bao-Yu; Li, Jing

    2009-05-15

    Using sludge as pore-forming agent, bentonite granule was acidified by sulfuric acid solution as a decolorant. The specific surface area and SEM were performed to characterize the structure of samples, and the new acidified sludge-bentonite granule was applied to the decoloration of reactive turquoise blue. The influencing factors of pH value, dosage, reaction time and reaction temperature were studied on the removal of the dyes. The important thermodynamics parameters (DeltaH0, DeltaS0, DeltaG) and the activation energy Ea were also acquired by experiment data processing. The results indicated that the adsorption isotherm fitted the isothermal adsorption equations of Langmuir better than Freundlich. The adsorption dynamics followed the law of the pseudo-second order kinetic equation, while the adsorption rate is 313 K > 303 K > 293 K. The low value of Ea which is 5.52 kJ x mol(-1) shows that physical adsorption is primary. And DeltaH0 > TDeltaS0 means that the influence of enthalpy is more remarkable than the entropy in the activation reaction. DeltaG > 0 also means the chemical reactions are not spontaneous.

  13. Coal-Water Slurry Fuels: An Overview,

    DTIC Science & Technology

    1983-07-12

    coal gasification and liquefication processes, the capital investment required is modest. While those synthetic fuel processes cost in the order of $4 billion for a 50,000 barrel per day manufacturing facility, a coal-water plant of that size is estimated at abut $80 million (one fiftieth). While the cost of synthetic fuels has been projected at about double that of oil, the costs for coal-water are estimated at 30% to 40% less than oil. Put another way, assuming a 4% energy loss in the coal-water slurry, the resulting fuel cost of the CWM is approximately $3/million BTU.

  14. SIFCON (Slurry Infiltrated Fiber Concrete) with Sand

    DTIC Science & Technology

    1988-09-01

    Phtogrphsf tpe and Identifatio % flowt tests teyYiinders U& U6 10 LE~~ 150 1 3= O-4 slurries also contained microsilica . Three different fiber types...Ash Infiltration tests and selected mixes Water Facility 26025 tap water Kirtland A.F. Base well no. 2 All Microsilica EMS 960 (bagged) Elkem...the end instead of the two. When there are the three sets of numbers, the first set indicates the percent of microsilica with respect to the cement in

  15. Behaviour of liquid-fed growing pigs provided with straw in various amounts and frequencies.

    PubMed

    Oxholm, L C; Steinmetz, H V; Lahrmann, H P; Nielsen, M B F; Amdi, C; Hansen, C F

    2014-11-01

    Straw possesses many characteristics that make it attractive to pigs and can therefore be effective in preventing negative penmate-directed behaviours. However, straw is difficult to handle in current vacuum slurry systems under most commercial conditions and can therefore only be used in limited amounts. To occupy pigs effectively, straw must remain attractive to pigs throughout the whole day; hence, have a certain degree of novelty. We investigated the penmate-directed behaviour of liquid-fed growing pigs in a production herd, assigned to five experimental treatments: 1×25, 1×50, 1×100, 2×50 and 4×25 g of chopped straw/pig per day, with 20 replicates of each treatment (pen was regarded as experimental unit). Behaviour was observed at two different growth stages; ~40 and 80 kg live weight of the pigs. Activity and exploratory behaviour directed at penmates, straw, pen components and the slatted floor were registered continuously for 15 min of each hour during day time (0600 to 2200 h) by use of video observation of three focal pigs per pen. The pigs were active for about one-third of the day corresponding to ~5 h/day. Of the active time, an average of 7% (35 min) was spent on penmate-directed behaviour. The pigs were more active and increased their straw-directed behaviour when provided with 100 g straw/pig per day compared with 25 and 50 g (P<0.001). However, penmate-directed behaviour was not reduced with an increased amount of straw (P>0.05), and there was no effect on pigs' behaviour when straw provision was increased per day (P>0.05). Pigs became less active and reduced their straw-directed activities when their weight increased from 40 to 80 kg live weight (P<0.001), but the amount of penmate-directed behaviour was similar (P>0.05). Further, the residual straw results indicated that perhaps a more frequent straw provision could help establish a more even level of fresh available straw during the day. However, the frequent straw provision did not occupy

  16. Multi-stage slurry system used for grinding and polishing materials

    DOEpatents

    Hed, P. Paul; Fuchs, Baruch A.

    2001-01-01

    A slurry system draws slurry from a slurry tank via one of several intake pipes, where each pipe has an intake opening at a different depth in the slurry. The slurry is returned to the slurry tank via a bypass pipe in order to continue the agitation of the slurry. The slurry is then diverted to a delivery pipe, which supplies slurry to a polisher. The flow of slurry in the bypass pipe is stopped in order for the slurry in the slurry tank to begin to settle. As the polishing continues, slurry is removed from shallower depths in order to pull finer grit from the slurry. When the polishing is complete, the flow in the delivery pipe is ceased. The flow of slurry in the bypass pipe is resumed to start agitating the slurry. In another embodiment, the multiple intake pipes are replaced by a single adjustable pipe. As the slurry is settling, the pipe is moved upward to remove the finer grit near the top of the slurry tank as the polishing process continues.

  17. Method and apparatus for improved wire saw slurry

    DOEpatents

    Costantini, Michael A.; Talbott, Jonathan A.; Chandra, Mohan; Prasad, Vishwanath; Caster, Allison; Gupta, Kedar P.; Leyvraz, Philippe

    2000-09-05

    A slurry recycle process for use in free-abrasive machining operations such as for wire saws used in wafer slicing of ingots, where the used slurry is separated into kerf-rich and abrasive-rich components, and the abrasive-rich component is reconstituted into a makeup slurry. During the process, the average particle size of the makeup slurry is controlled by monitoring the condition of the kerf and abrasive components and making necessary adjustments to the separating force and dwell time of the separator apparatus. Related pre-separator and post separator treatments, and feedback of one or the other separator slurry output components for mixing with incoming used slurry and recirculation through the separator, provide further effectiveness and additional control points in the process. The kerf-rich component is eventually or continually removed; the abrasive-rich component is reconstituted into a makeup slurry with a controlled, average particle size such that the products of the free-abrasive machining method using the recycled slurry process of the invention are of consistent high quality with less TTV deviation from cycle to cycle for a prolonged period or series of machining operations.

  18. EVALUATION OF CARBON BLACK SLURRIES AS CLEAN BURNING FUELS

    EPA Science Inventory

    Experiments were performed to examine the pumpability, atomization and combustion characteristics of slurries made of mixtures of carbon black with No. 2 fuel oil and methanol. Carbon black-No. 2 fuel oil and carbon black-methanol slurries, with carbon black contents of up to 50 ...

  19. Lime slurry use at the Industrial Wastewater Pretreatment Facility

    SciTech Connect

    Rice, L.E.; Hughes, R.W.; Baggett, G.

    1996-04-01

    The use of lime slurry at the IWPF demonstrated many benefits. Hazardous chemical use was reduced, solids handling was improved, water quality was enhanced and there has been a cost savings. The lime slurry also enabled the plant to begin treating the soluble oil waste, which we were not able to do in the past.

  20. Self-Organization in Granular Slurries

    NASA Astrophysics Data System (ADS)

    Ottino, Julio M.; Jain, Nitin; Lueptow, Richard M.; Khakhar, Devang V.

    2000-11-01

    Mixtures of tumbled granular materials under flow exhibit various intriguing types of un-mixing or self-organization. Small differences in particles' density, size or shape may trigger the effect. Nearly all studies to date have addressed the case of dry granular media, where the interparticle fluid is typically air. Here we report the existence of self-organization in wet granular media or slurries, mixtures of particles of different sizes dispersed in a lower density liquid. Technological examples appear in cement, ceramics, fine chemicals, and in the food industry; examples in nature appear in evolution of landslides and transport in river sediments. In spite of significantly different physics at the particle level, both axial banding (alternating bands rich in small and large particles in a long rotating cylinder) and radial segregation (in quasi 2D containers) are observed in slurries. However, axial segregation is significantly faster and the spectrum of outcomes is richer. Moreover, experiments with suitable fluids, reveal, for the first time, the internal structure of axially segregated systems, something that up to now has been accessible only via magnetic resonance imaging (MRI) experimentation.

  1. Rheological Modifier Testing with DWPF Process Slurries

    SciTech Connect

    MICHAEL, STONE

    2004-02-01

    Rheological modification agents were tested on simulated SRAT and SME products to determine if a suitable agent could be found for the DWPF process slurries. The agents tested were dispersants that lower the rheological properties of slurries by preventing agglomerization. Dolapix CE64, an ethylene glycol, and Disperse-Ayd W28, a polyacrylate, were the most effective dispersants tested. Further evaluation and testing should be performed on Dolapix CE64 and Disperse-Ayd W28 to determine if implementation is possible in DWPF. The initial phase of future work will include optimization of the rheology modifier by the Illinois Institute of Technology (IIT) and development of a maximum concentration limit for the rheology modifiers. IIT has been commissioned to evaluate the properties of these chemicals to determine if the chemical makeup can be optimized to enhance the properties of these modifiers. An initial concentration limit based upon the DWPF flammability limit and other constraints should be calculated to determine the potential downstream impacts.

  2. Solids flow rate measurement in dense slurries

    SciTech Connect

    Porges, K.G.; Doss, E.D.

    1993-09-01

    Accurate and rapid flow rate measurement of solids in dense slurries remains an unsolved technical problem, with important industrial applications in chemical processing plants and long-distance solids conveyance. In a hostile two-phase medium, such a measurement calls for two independent parameter determinations, both by non-intrusive means. Typically, dense slurries tend to flow in laminar, non-Newtonian mode, eliminating most conventional means that usually rely on calibration (which becomes more difficult and costly for high pressure and temperature media). These issues are reviewed, and specific solutions are recommended in this report. Detailed calculations that lead to improved measuring device designs are presented for both bulk density and average velocity measurements. Cross-correlation, chosen here for the latter task, has long been too inaccurate for practical applications. The cause and the cure of this deficiency are discussed using theory-supported modeling. Fluid Mechanics are used to develop the velocity profiles of laminar non-Newtonian flow in a rectangular duct. This geometry uniquely allows the design of highly accurate `capacitive` devices and also lends itself to gamma transmission densitometry on an absolute basis. An absolute readout, though of less accuracy, is also available from a capacitive densitometer and a pair of capacitive sensors yields signals suitable for cross-correlation velocity measurement.

  3. Effective Compressibility of a Bubbly Slurry.

    PubMed

    Kam, S. I.; Gauglitz, P. A.; Rossen, W. R.

    2001-09-01

    The goal of this study is to fit model parameters to changes in waste level in response to barometric pressure changes in underground storage tanks at the Hanford Site. This waste compressibility is a measure of the quantity of gas, typically hydrogen and other flammable gases, that can pose a safety hazard, retained in the waste. A one-dimensional biconical-pore-network model for compressibility of a bubbly slurry is presented in a companion paper. Fitting these results to actual waste level changes in the tanks implies that bubbles in the slurry layer are long and the ratio of pore-body radius to pore-throat radius is close to 1; unfortunately, compressibility can not be quantified unambiguously from the data without additional information on pore geometry. Therefore, determining the quantity of gas in the tanks requires more than just waste-level data. The non-uniqueness of the fit is also found with two other simple models: a capillary-tube model with contact angle hysteresis and a spherical-pore model. Copyright 2001 Academic Press.

  4. Numerical simulation of turbulent slurry flows

    NASA Astrophysics Data System (ADS)

    Haghgoo, Mohammad Reza; Spiteri, Reymond J.; Bergstrom, Donlad J.

    2016-11-01

    Slurry flows, i.e., the flow of an agglomeration of liquid and particles, are widely employed in many industrial applications, such as hydro-transport systems, pharmaceutical batch crystallizers, and wastewater disposal. Although there are numerous studies available in the literature on turbulent gas-particle flows, the hydrodynamics of turbulent liquid-particle flows has received much less attention. In particular, the fluid-phase turbulence modulation due to the particle fluctuating motion is not yet well understood and remains challenging to model. This study reports the results of a numerical simulation of a vertically oriented slurry pipe flow using a two-fluid model based on the kinetic theory of granular flows. The particle stress model also includes the effects of frictional contact. Different turbulence modulation models are considered, and their capability to capture the characteristic features of the turbulent flow is assessed. The model predictions are validated against published experimental data and demonstrate the significant effect of the particles on the fluid-phase turbulence.

  5. Improving feed slurry rheology by colloidal techniques

    SciTech Connect

    Heath, W.O.; Ternes, R.L.

    1984-06-01

    Pacific Northwest Laboratory (PSN) has investigated three colloidal techniques in the laboratory to improve the sedimentation and flowability of Hanford simulated (nonradioactive) current acid waste (CAW) melter feed slurry: polymer-induced bridging flocculation; manipulating glass former (raw SiO/sub 2/ or frit) particle size; and alteration of nitric acid content. All three methods proved successful in improving the rheology of the simulated CAW feed. This initially had exhibited nearly worst-case flow and clogging properties, but was transformed into a flowable, resuspendable (nonclogging) feed. While each has advantages and disadvantages, the following three specific alternatives proved successful: addition of a polyelectrolyte in 2000 ppM concentration to feed slurry; substitution of a 49 wt % SiO/sub 2/ colloidal suspension (approx. 10-micron particle size) for the -325 mesh (less than or equal to 44-micron particle size) raw-chemical SiO/sub 2/; and increase of nitric acid content from the reference 1.06 M to optimum 1.35 M. The first method, polymer-induced bridging flocculation, results in a high sediment volume, nonclogging CAW feed. The second method, involving the use of colloidal silica particles results in a nonsedimenting feed that when left unagitated forms a gel. The third method, increase in feed acidity, results in a highly resuspendable (nonclogging) melter feed. Further research is therefore required to determine which of the three alternatives is the preferred method of achieving rheological control of CAW melter feeds.

  6. Bubble column apparatus for separating wax from catalyst slurry

    DOEpatents

    Neathery, James K.; Davis, Burtron H.

    2004-07-13

    Novel methods and devices for production of liquid hydrocarbon products from gaseous reactants are disclosed. In one aspect, a method for separating a liquid hydrocarbon, typically a wax, from a catalyst containing slurry is provided, comprising passing the slurry through at least one downcomer extending from an overhead separation chamber and discharging into the bottom of a slurry bubble column reactor. The downcomer includes a cross-flow filtration element for separating a substantially particle-free liquid hydrocarbon for downstream processing. In another aspect, a method for promoting plug-flow movement in a recirculating slurry bubble column reactor is provided, comprising discharging the recirculating slurry into the reactor through at least one downcomer which terminates near the bottom of the reactor. Devices for accomplishing the above methods are also provided.

  7. Chemists report slurry breakthroughs for syngas-to-alcohol process

    SciTech Connect

    Rotman, D.

    1996-04-24

    Scientists at North Carolina State University (Raleigh) report that they have developed an alcohol synthesis process that uses a high-temperature slurry reactor with a conventional zinc chromite methanol catalyst. The scientists say it is the first time zinc-chromite catalysts have been used in slurry reactors at temperatures as high as 375 C. They add that it could lead to a synthesis gas (syngas)-based route to higher alcohols and to broader commercial applications for slurry reactors. Slurry reactors typically operate at less than 300 C, limiting applications for many high-volume industrial applications. By extending the temperature 100 C, says George Roberts, a chemist at North Carolina State, the work could {open_quotes}open up chemistry never run in slurry reactors before.{close_quotes} Roberts points to potential for use in partial oxidation reactions and synthesis routes involving formaldehyde.

  8. Phenanthrene removal from soil slurries with surfactant-treated oxides

    SciTech Connect

    Park, J.W.; Jaffe, P.R.

    1995-06-01

    A soil-slurry washing technique to decontaminate soils containing low-solubility nonionic organic pollutants was investigated, using phenanthrene as a model pollutant. The technique is based on first transferring the sorbed phenanthrene from the soil to anionic surfactant-coated oxide particles, and then separating these anionic surfactant-coated oxide particles with the sorbed phenanthrene from the soil slurry via a magnetic separation technique. The decontamination of two soils with different particle sizes and soil organic matter content was investigated. The proposed soil-slurry washing technique was effective in removing a strongly sorbing nonionic organic contaminant from soil slurries. Various operational scenarios of multistage soil-slurry reactors were evaluated with a mathematical model.

  9. Fuel injection of coal slurry using vortex nozzles and valves

    DOEpatents

    Holmes, Allen B.

    1989-01-01

    Injection of atomized coal slurry fuel into an engine combustion chamber is achieved at relatively low pressures by means of a vortex swirl nozzle. The outlet opening of the vortex nozzle is considerably larger than conventional nozzle outlets, thereby eliminating major sources of failure due to clogging by contaminants in the fuel. Control fluid, such as air, may be used to impart vorticity to the slurry and/or purge the nozzle of contaminants during the times between measured slurry charges. The measured slurry charges may be produced by a diaphragm pump or by vortex valves controlled by a separate control fluid. Fluidic circuitry, employing vortex valves to alternatively block and pass cool slurry fuel flow, is disclosed.

  10. Improved Fischer-Tropsch Slurry Reactors

    SciTech Connect

    Andrew Lucero

    2009-03-20

    The conversion of synthesis gas to hydrocarbons or alcohols involves highly exothermic reactions. Temperature control is a critical issue in these reactors for a number of reasons. Runaway reactions can be a serious safety issue, even raising the possibility of an explosion. Catalyst deactivation rates tend to increase with temperature, particularly of there are hot spots in the reactor. For alcohol synthesis, temperature control is essential because it has a large effect on the selectivity of the catalysts toward desired products. For example, for molybdenum disulfide catalysts unwanted side products such as methane, ethane, and propane are produced in much greater quantities if the temperature increases outside an ideal range. Slurry reactors are widely regarded as an efficient design for these reactions. In a slurry reactor a solid catalyst is suspended in an inert hydrocarbon liquid, synthesis gas is sparged into the bottom of the reactor, un-reacted synthesis gas and light boiling range products are removed as a gas stream, and heavy boiling range products are removed as a liquid stream. This configuration has several positive effects for synthesis gas reactions including: essentially isothermal operation, small catalyst particles to reduce heat and mass transfer effects, capability to remove heat rapidly through liquid vaporization, and improved flexibility on catalyst design through physical mixtures in addition to use of compositions that cannot be pelletized. Disadvantages include additional mass transfer resistance, potential for significant back-mixing on both the liquid and gas phases, and bubble coalescence. In 2001 a multiyear project was proposed to develop improved FT slurry reactors. The planned focus of the work was to improve the reactors by improving mass transfer while considering heat transfer issues. During the first year of the project the work was started and several concepts were developed to prepare for bench-scale testing. Power

  11. Type C bovine botulism outbreak due to carcass contaminated non-acidified silage.

    PubMed

    Myllykoski, J; Lindström, M; Keto-Timonen, R; Söderholm, H; Jakala, J; Kallio, H; Sukura, A; Korkeala, H

    2009-02-01

    The first reported bovine botulism outbreak in Finland is described. Nine out of 90 cattle on a dairy farm died after being fed non-acidified silage contaminated by animal carcasses. Type C botulinum neurotoxin gene was detected in one heifer by polymerase chain reaction (PCR) and the neurotoxin was detected by the mouse bioassay. Clostridium botulinum type C was isolated from liver samples. The isolated strain was identified with amplified fragment length polymorphism (AFLP) analysis as group III C. botulinum. To our knowledge, this is the first time that a type C bovine botulism outbreak has been diagnosed by PCR and confirmed by subsequent isolation and AFLP identification of the disease strain. The importance of the acidification process in silage production to inhibit C. botulinum toxin production in silage and thus to prevent further botulism outbreaks is emphasized. Nevertheless, preformed toxin in the carcass is not destroyed by acid.

  12. Rapid restoration of methanogenesis in an acidified UASB reactor treating 2,4,6-trichlorophenol (TCP).

    PubMed

    Díaz-Báez, María Consuelo; Valderrama-Rincon, Juan Daniel

    2017-02-15

    Anaerobic bioreactors are often used for removal of xenobiotic and highly toxic pollutants from wastewater. Most of the time, the pollutant is so toxic that the stability of the reactor becomes compromised. It is well known that methanogens are one of the most sensitive organisms in the anaerobic consortia and hence the stability of the reactors is highly dependant on methanogenesis. Unfortunately few studies have focused on recovering the methanogenic activity once it has been inhibited by highly toxic pollutants. Here we establish a quick recovery strategy for neutralization of an acidified UASB reactor after failure by intoxication with an excess of TCP in the influent. Once the reactor returned to pH values compatible with methanogenesis, biogas production was re-started after one day and the system was re-acclimated to TCP. Successful removal of TCP from synthetic wastewater was shown for concentrations up to 70mg/L after restoration.

  13. Purification of empty fruit bunch (EFB) and kenaf soda lignin with acidified water

    NASA Astrophysics Data System (ADS)

    Hashim, Sharifah Nurul Ain Syed; Zakaria, Sarani; Jaafar, Sharifah Nabihah Syed; Hua, Chia Chin

    2014-09-01

    In this current study, the soda lignins from empty fruit bunch (EFB) and kenaf core were recovered by two step precipitation method. The objective of this research is to study the purity of lignin by washing the lignins with acidified water. The purified lignins were undergone characterization by FT-IR, Uv-Vis and XRD. The FT-IR analysis shows that kenaf core has Guaiacyl(G) and Syringyl(S) unit meanwhile EFB has Hydroxyphenyl(H), Guaiacyl(G) and Syringyl(S) unit of lignin. As for XRD analysis, the non-purified shows that the existence of impurities which is salt (NaCl). The UV analysis shows the higher absorbance which lead to the purity of lignin.

  14. Acidifier application rate impacts on ammonia emissions from US roaster chicken houses

    NASA Astrophysics Data System (ADS)

    Shah, Sanjay B.; Grimes, Jesse L.; Oviedo-Rondón, Edgar O.; Westerman, Philip W.

    2014-08-01

    Due to its potential environmental and public health impacts, emissions of ammonia (NH3) as well as several other gases from US livestock farms may be regulated. Broiler houses are important sources of NH3 emissions. However, there are no emissions data from roaster (8-12 wk old broilers, ˜4 kg ea.) houses. Producers treat the litter in broiler houses with acidifiers, such as sodium bisulfate (SBS, NaHSO4) to reduce ammonia production and protect bird health. However, there is very little data on the effect of acidifiers, particularly at high application rates on ammonia emissions. The impact of different SBS application rates [High (0.95-1.46 kg m-2, whole house), Medium (0.73 kg m-2, whole house), Low (0.37-0.49 kg m-2, whole house), and Control (0.37-0.49 kg m-2, brood chamber)] on ammonia emissions was evaluated in commercial roaster houses over 22 months spanning eight flocks. Ammonia emission from each fan was measured with an acid scrubber that operated only when the fan operated. Emissions were calculated using >95% measured data with the rest being estimated using robust methods. Exhaust ammonia-N concentrations were inversely correlated with the SBS application rates. Emission rates on animal unit (AU, where 1 AU = 500 kg live-mass) basis (ER, g d-1 AU-1) were reduced by 27, 13, and 5%, respectively, in the High, Medium, and Low treatments vs. the Control treatment (mean: 100 g d-1 AU-1, range: 86-114 g d-1 AU-1). Emission rates for the Control treatment measured in this study on roasters were mostly higher than ERs in the literature. Differences in ERs are not only due to diet, environmental and management conditions, but also due to measurement methods.

  15. Eubiotic effect of a dietary acidifier (potassium diformate) on the health status of cultured Oreochromis niloticus.

    PubMed

    Abu Elala, Nermeen M; Ragaa, Naela M

    2015-07-01

    In connection with the global demand for safe human food and the production of environmentally friendly aquaculture products, acidifiers are natural organic acids and salts that have received considerable attention as animal-feed additives. The current study was designed to evaluate the effects of potassium diformate (KDF) on the growth performance and immunity of cultured Oreochromis niloticus (O. niloticus). Four iso-nitrogenous and iso-caloric rations containing graded levels of KDF, including 0% (control basal diet), 0.1%, 0.2% and 0.3%, were fed separately to four equal fish groups (30 fish/group with an initial body weight of 53.49 ± 6.15 g) for sixty days. At the end of the experimental period, the fish groups fed on 0.2% and 0.3% KDF exhibited significant improvements in their feed intake, live weight gain, specific growth rate, feed conversion ratio and protein efficiency ratio, with concomitant improvement of their apparent protein digestibility (p < 0.05). Dietary supplementation of 0.3% KDF appeared to stimulate the beneficial intestinal flora; a proliferation was observed of indigenous probionts (Eubiosis) associated with the relative activation of cellular and humeral innate immunity (phagocytic activity/index, nitroblue tetrazolium reduction test and serum/gut mucous lysozyme activity). The cumulative mortality of the fish groups fed on KDF and challenged orally with Aeromonas hydrophila was lower than that of the control group. The resistance against diseases increased with dietary KDF in a dose-dependent manner. Thus, we conclude that the use of acidifiers can be an efficient tool to achieve sustainable, economical and safe fish production.

  16. Eubiotic effect of a dietary acidifier (potassium diformate) on the health status of cultured Oreochromis niloticus

    PubMed Central

    Abu Elala, Nermeen M.; Ragaa, Naela M.

    2014-01-01

    In connection with the global demand for safe human food and the production of environmentally friendly aquaculture products, acidifiers are natural organic acids and salts that have received considerable attention as animal-feed additives. The current study was designed to evaluate the effects of potassium diformate (KDF) on the growth performance and immunity of cultured Oreochromis niloticus (O. niloticus). Four iso-nitrogenous and iso-caloric rations containing graded levels of KDF, including 0% (control basal diet), 0.1%, 0.2% and 0.3%, were fed separately to four equal fish groups (30 fish/group with an initial body weight of 53.49 ± 6.15 g) for sixty days. At the end of the experimental period, the fish groups fed on 0.2% and 0.3% KDF exhibited significant improvements in their feed intake, live weight gain, specific growth rate, feed conversion ratio and protein efficiency ratio, with concomitant improvement of their apparent protein digestibility (p < 0.05). Dietary supplementation of 0.3% KDF appeared to stimulate the beneficial intestinal flora; a proliferation was observed of indigenous probionts (Eubiosis) associated with the relative activation of cellular and humeral innate immunity (phagocytic activity/index, nitroblue tetrazolium reduction test and serum/gut mucous lysozyme activity). The cumulative mortality of the fish groups fed on KDF and challenged orally with Aeromonas hydrophila was lower than that of the control group. The resistance against diseases increased with dietary KDF in a dose-dependent manner. Thus, we conclude that the use of acidifiers can be an efficient tool to achieve sustainable, economical and safe fish production. PMID:26199753

  17. Fatty acid composition and biogenic amines in acidified and fermented fish silage: a comparison study.

    PubMed

    Özyurt, Gülsün; Gökdoğan, Saadet; Şimşek, Ayşe; Yuvka, Ilknur; Ergüven, Merve; Kuley Boga, Esmeray

    2016-01-01

    In the presented study, ensiling of discard fish by acidification or fermentation was evaluated. Klunzinger's ponyfish which is a discard fish was used for the production of fish silage by acidification (3% formic acid for Method FA; 1.5% formic and 1.5% sulphuric acid for Method FASA) and fermentation (Lactobacillus plantarum for Method LP and Streptococcus thermophilus for Method ST). The chemical, microbiological and nutritional properties of the differently preserved fish silages were estimated during a storage period of 60 d at ambient temperature. Compared to the raw material, a slight increase in saturated fatty acids and a slight decrease in polyunsaturated fatty acids were observed in all silages. At the end of the storage period, the aerobic bacteria counts after applying Methods FA, FASA, LP and ST amounted to 2.35, 2.39, 5.77 and 5.43 log cfu/g, respectively. The analysis of thiobarbituric acid revealed that acidification of silages accelerated the lipid oxidation. Nine biogenic amines were found in raw fish and different silages. The initial histamine concentration in raw fish was 0.17 mg/100 g and in all silages it remained at low levels during the storage period. The initial tyramine content was found to be 1.56 mg/100 g in raw fish and increased significantly in all silages. The increase of the tyramine content in fermented silages was considerably higher than in acidified silages (23-48 mg/100 g and 5-10 mg/100 g, respectively). It can be concluded that acidified or fermented fish silage should be considered as potential feed component for animals because of its high nutritional value and appropriate microbiological and chemical quality.

  18. Testing of In-Line Slurry Monitors and Pulsair Mixers with Radioactive Slurries

    SciTech Connect

    Hylton, T.D.; Bayne, C.K.

    1999-08-01

    Three in-line slurry monitoring instruments were demonstrated, tested, and evaluated for their capability to determine the transport properties of radioactive slurries. The instruments included the Endress + Hauser Promass 63M Coriolis meter for measuring density, the Lasentec M600P for measuring particle size distribution, and a prototype ultrasonic monitor that was developed by Argonne National Laboratory for measuring suspended solids concentration. In addition, the power consumption of the recirculation pump was monitored to determine whether this parameter could be used as a tool for in-line slurry monitoring. The Promass 63M and the M600P were also evaluated as potential indicators of suspended solids concentration. In order to use the Promass 63M as a suspended solids monitor, the densities of the fluid phase and the dry solid particle phase must be known. In addition, the fluid phase density and the dry solids density must remain constant, as any change will affect the correlation between the slurry density and the suspended solids concentration. For the M600P, the particle size distribution would need to remain relatively constant. These instruments were demonstrated and tested at the Gunite and Associated Tanks Remediation Project at the Oak Ridge National Laboratory. The testing of the instruments was conducted in parallel with the testing of a Pulsair mixing system, which was used to mix the contents of the selected tank. A total of six tests were performed. A submersible pump was positioned at two depths, while the Pulsair system was operated at three mixing rates.

  19. Study of acidified ignitable liquid residues in fire debris by solid-phase microextraction with gas chromatography and mass spectrometry.

    PubMed

    Martín-Alberca, Carlos; García-Ruiz, Carmen; Delémont, Olivier

    2015-07-14

    The detection and identification of ignitable liquid residues in fire debris can be meaningful in fire investigations. However, background pyrolysis products and weathering hinder the identification and classification steps. In addition to those processes, the acidification of the ignitable liquids before the combustion process could make those tasks even more difficult. Nevertheless, there are no systematic studies assessing the extraction, analysis and composition of acidified ignitable liquid residues obtained from fire debris. In this work, a methodology for the study of acidified ignitable liquid residues in fire debris by solid-phase microextraction with gas chromatography and mass spectrometry is proposed. This methodology has been evaluated, first with simulated solutions (gasoline-sulphuric acid mixtures set on fire under controlled conditions), and then with analysis of samples from real fire debris obtained from 18 chemical ignition Molotov cocktails made with sulfuric acid and three different ignitable liquids (two types of gasoline and diesel fuel). In addition, the extensive modifications observed in chromatograms of acidified ignitable liquid residues regarding neat and weathered samples were studied. These alterations were produced by the combustion and acidification processes. As a consequence, tert-butylated compounds are proposed as diagnostic indicators for the identification of acidified gasoline in fire debris, even in strongly weathered samples. This article is protected by copyright. All rights reserved.

  20. Comparison of the effects of thermal stress and CO₂-driven acidified seawater on fertilization in coral Acropora digitifera.

    PubMed

    Iguchi, Akira; Suzuki, Atsushi; Sakai, Kazuhiko; Nojiri, Yukihiro

    2015-08-01

    Global warming (GW) and ocean acidification (OA) have been recognized as severe threats for reef-building corals that support coral reef ecosystems, but these effects on the early life history stage of corals are relatively unknown compared with the effects on calcification of adult corals. In this study, we evaluated the effects of thermal stress and CO2-driven acidified seawater on fertilization in a reef-building coral, Acropora digitifera. The fertilization rates of A. digitifera decreased in response to thermal stress compared with those under normal seawater conditions. In contrast, the changes of fertilization rates were not evident in the acidified seawater. Generalized Linear Mixed Model (GLMM) predicted that sperm/egg crosses and temperature were explanatory variables in the best-fitted model for the fertilization data. In the best model, interactions between thermal stress and acidified seawater on the fertilization rates were not selected. Our results suggested that coral fertilization is more sensitive to future GW than OA. Taking into consideration the previous finding that sperm motility of A. digitifera was decreased by acidified seawater, the decrease in coral cover followed by that of sperm concentration might cause the interacting effects of GW and OA on coral fertilization.

  1. Thermal processing of acidified foods with pH 4.1 to pH 4.6

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Shelf-stable acidified foods with a pH at or below 4.6 must be processed to achieve a 5-log reduction for vegetative bacterial pathogens. Published research does not exist to adequately support the Food and Drug Administration process filings for products with pH 4.1–4.6 or to define critical limits...

  2. Preservation of acidified cucumbers with a combination of fumaric acid and cinnamaldehyde that target lactic acid bacteria and yeasts

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The naturally occurring compound, fumaric acid, was evaluated as a potential preservative for the long-term storage of cucumbers. Fumaric acid inhibited growth of lactic acid bacteria (LAB) in an acidified cucumber juice medium model system resembling conditions that could allow preservation of cucu...

  3. Determination of 5-log reduction times for food pathogens in acidified cucumbers during storage at 10 and 25 degrees C.

    PubMed

    Breidt, Fred; Hayes, Janet; McFeeters, Roger F

    2007-11-01

    Outbreaks of acid-resistant foodborne pathogens in acid foods with pH values below 4.0, including apple cider and orange juice, have raised concerns about the safety of acidified vegetable products. For acidified vegetable products with pH values between 3.3 and 4.6, previous research has demonstrated that thermal treatments are needed to achieve a 5-log reduction in the numbers of Escherichia coli O157:H7, Listeria monocytogenes, or Salmonella enterica. For some acidified vegetable products with a pH of 3.3 or below, heat processing can result in unacceptable product quality. The purpose of this study was to determine the holding times needed to achieve a 5-log reduction in E. coli O157:H7, L. monocytogenes, and S. enterica strains in acidified vegetable products with acetic acid as the primary acidulant, a pH of 3.3 or below, and a minimum equilibrated temperature of 10 degrees C. We found E. coli O157:H7 to be the most acid-resistant microorganism for the conditions tested, with a predicted time to achieve a 5-log reduction in cell numbers at 10 degrees C of 5.7 days, compared with 2.1 days (51 h) for Salmonella or 0.5 days (11.2 h) for Listeria. At 25 degrees C, the E. coli O157:H7 population achieved a 5-log reduction in 1.4 days (34.3 h).

  4. Trends in Surface Water Chemistry in Acidified Areas in Europe and North America from 1990 to 2008

    EPA Science Inventory

    Acidification of lakes and rivers is still an environmental concern despite reduced emissions of acidifying compounds. We analyzed trends in surface water chemistry of 173 acid-sensitive sites from 12 regions in Europe and North America. In 11 of 12 regions, non-marine sulphate (...

  5. Growth inhibition of Cronobacter spp. strains in reconstituted powdered infant formula acidified with organic acids supported by natural stomach acidity.

    PubMed

    Zhu, S; Schnell, S; Fischer, M

    2013-09-01

    Cronobacter is associated with outbreaks of rare, but life-threatening cases of meningitis, necrotizing enterocolitis, and sepsis in newborns. This study was conducted to determine the effect of organic acids on growth of Cronobacter in laboratory medium and reconstituted powdered infant formula (PIF) as well as the bacteriostatic effect of slightly acidified infant formula when combined with neonatal gastric acidity. Inhibitory effect of seven organic acids on four acid sensitive Cronobacter strains was determined in laboratory medium with broth dilution method at pH 5.0, 5.5 and 6.0. Acetic, butyric and propionic acids were most inhibitive against Cronobacter in the laboratory medium. The killing effect of these three acids was partially buffered in reconstituted PIF. Under neonatal gastric acid condition of pH 5.0, the slightly acidified formula which did not exert inhibition effect solely reduced significantly the Cronobacter populations. A synergistic effect of formula moderately acidified with organic acid combined with the physiological infant gastric acid was visible in preventing the rapid growth of Cronobacter in neonatal stomach. The study contributed to a better understanding of the inhibitory effect of organic acids on Cronobacter growth in different matrixes and provided new ideas in terms of controlling bacteria colonization and translocation by acidified formula.

  6. Developing anthracite coal water slurry fuel. Final report

    SciTech Connect

    Simmon, F.J.; Keller, D.V.; Marino, J.; Keller, D.S.; Ask, T.E.

    1993-09-01

    Public law has directed the Department of Defense (DOD) to increase the use of coal, particularly anthracite, at steam generating facilities. This study evaluates the feasibility of producing slurry fuel from anthracite coal and examines the combustion characteristics of the anthracite/water fuel slurry. The T-Process, a proprietary process developed by Otisca Industries, Ltd., Syracuse, NY, was used to produce anthracite-based coal water slurries for testing and combustion. Although it is feasible to manufacture anthracite water fuel, the slurries used in this research would not burn well without substantial amounts of natural gas cofiring. Stable combustion with reduced support fuel can probably be achieved by chemically or physically modifying the factors that affect combustion. Additional research to determine the differences between anthracite and bituminous slurries, to increase the residence time for anthracite slurries, and to manufacture slurries with oil rather than water needs to be conducted to help the DOD meet anthracite purchase/consumption targets. Coal, Combustion, Coal water fuel, Anthracite coal.

  7. Desulfurization from Bauxite Water Slurry (BWS) Electrolysis

    NASA Astrophysics Data System (ADS)

    Gong, Xuzhong; Ge, Lan; Wang, Zhi; Zhuang, Siyuan; Wang, Yuhua; Ren, Lihui; Wang, Mingyong

    2016-02-01

    Feasibility of high-sulfur bauxite electrolysis desulfurization was examined using the electrochemical characterization, XRD, DTA, and FTIR. The cyclic voltammetry curves indicated that bauxite water slurry (BWS) electrolysis in NaOH system was controlled by diffusion. Additionally, the desulfurization effect of NaCl as the electrolyte was significantly better than that of NaOH as an electrolyte. As the stirring rate increased, the desulfurization ratio in NaCl system was not increased obviously, while the desulfurization ratio in NaOH system increased significantly, indicating further that electrolysis desulfurization in NaOH solution was controlled by diffusion. According to XRD, DTA, and FTIR analysis, the characteristic peaks of sulfur-containing phase in bauxite after electrolysis weakened or disappeared, indicating that the pyrite in bauxite was removed from electrolysis. Finally, the electrolytic desulfurization technology of bauxite was proposed based on the characteristics of BWS electrolysis.

  8. Secondary breakup of coal water slurry drops

    NASA Astrophysics Data System (ADS)

    Zhao, Hui; Liu, Hai-Feng; Xu, Jian-Liang; Li, Wei-Feng

    2011-11-01

    To investigate secondary atomization of coal water slurry (CWS), deformation and breakup of eight kinds of CWS drops are presented using high speed digital camera. Based on morphology, deformation and breakup regimes of CWS drops can be termed some different modes: deformation, multimode breakup (including two sub-modes: hole breakup and tensile breakup), and shear breakup. Correlations on the ranges of breakup modes are also obtained. The conventional Weber number and Ohnesorge number are found to be insufficient to classify all breakup modes of CWS drops, so two other non-dimensional numbers based on rheology of CWS are suggested to use in the deformation and breakup regime map. Finally, total breakup time is studied and correlated, which increases with Ohnesorge number.

  9. Hydrodynamic models for slurry bubble column reactors

    SciTech Connect

    Gidaspow, D.

    1995-12-31

    The objective of this investigation is to convert a {open_quotes}learning gas-solid-liquid{close_quotes} fluidization model into a predictive design model. This model is capable of predicting local gas, liquid and solids hold-ups and the basic flow regimes: the uniform bubbling, the industrially practical churn-turbulent (bubble coalescence) and the slugging regimes. Current reactor models incorrectly assume that the gas and the particle hold-ups (volume fractions) are uniform in the reactor. They must be given in terms of empirical correlations determined under conditions that radically differ from reactor operation. In the proposed hydrodynamic approach these hold-ups are computed from separate phase momentum balances. Furthermore, the kinetic theory approach computes the high slurry viscosities from collisions of the catalyst particles. Thus particle rheology is not an input into the model.

  10. Ice slurry cooling development and field testing

    SciTech Connect

    Kasza, K.E.; Hietala, J.; Wendland, R.D.; Collins, F.

    1992-07-01

    A new advanced cooling technology collaborative program is underway involving Argonne National Laboratory (ANL), Northern States Power (NSP) and the Electric Power Research Institute (EPRI). The program will conduct field tests of an ice slurry distributed load network cooling concept at a Northern States Power utility service center to further develop and prove the technology and to facilitate technology transfer to the private sector. The program will further develop at Argonne National Laboratory through laboratory research key components of hardware needed in the field testing and develop an engineering data base needed to support the implementation of the technology. This program will sharply focus and culminate research and development funded by both the US Department of Energy and the Electric Power Research Institute on advanced cooling and load management technology over the last several years.

  11. Ice slurry cooling development and field testing

    SciTech Connect

    Kasza, K.E. ); Hietala, J. ); Wendland, R.D. ); Collins, F. )

    1992-01-01

    A new advanced cooling technology collaborative program is underway involving Argonne National Laboratory (ANL), Northern States Power (NSP) and the Electric Power Research Institute (EPRI). The program will conduct field tests of an ice slurry distributed load network cooling concept at a Northern States Power utility service center to further develop and prove the technology and to facilitate technology transfer to the private sector. The program will further develop at Argonne National Laboratory through laboratory research key components of hardware needed in the field testing and develop an engineering data base needed to support the implementation of the technology. This program will sharply focus and culminate research and development funded by both the US Department of Energy and the Electric Power Research Institute on advanced cooling and load management technology over the last several years.

  12. PCB dechlorination in anaerobic soil slurry reactors

    SciTech Connect

    Klasson, K.T.; Evans, B.S.

    1993-11-29

    Many industrial locations, including the US Department of Energy`s, have identified needs for treatment of polychlorinated biphenyl (PCB) wastes and remediation of PCB-contaminated sites. Biodegradation of PCBs is a potentially effective technology for the treatment of PCB-contaminated soils and sludges, including mixed wastes; however, a practical remediation technology has not yet been demonstrated. In laboratory experiments, soil slurry bioreactors inoculated with microorganisms extracted from PCB-contaminated sediments from the Hudson River have been used to obtain anaerobic dechlorination of PCBS. The onset of dechlorination activity can be accelerated by addition of nutritional amendments and inducers. After 15 weeks of incubation with PCB-contaminated soil and nutrient solution, dechlorination has been observed under several working conditions. The best results show that the average chlorine content steadily dropped from 4.3 to 3.5 chlorines per biphenyl over a 15-week period.

  13. Latex migration in battery slurries during drying.

    PubMed

    Lim, Sanghyuk; Ahn, Kyung Hyun; Yamamura, Masato

    2013-07-02

    We used real-time fluorescence microscopy to investigate the migration of latex particles in drying battery slurries. The time evolution of the fluorescence signals revealed that the migration of the latex particles was suppressed above the entanglement concentration of carboxymethyl cellulose (CMC), while it was significantly enhanced when CMC fully covered the surfaces of the graphite particles. In particular, a two-step migration was observed when the graphite particles flocculated by depletion attraction at high CMC/graphite mass ratios. The transient states of the nonadsorbing CMC and graphite particles in a medium were discussed, and the uses of this novel measurement technique to monitor the complex drying processes of films were demonstrated.

  14. Slurry fired heater cold-flow modelling

    SciTech Connect

    Moujaes, S.F.

    1983-07-01

    This report summarizes the experimental and theoretical work leading to the scale-up of the SRC-I Demonstration Plant slurry fired heater. The scale-up involved a theoretical model using empirical relations in the derivation, and employed variables such as flow conditions, liquid viscosity, and slug frequency. Such variables have been shown to affect the heat transfer characteristics ofthe system. The model assumes that, if all other variables remain constant, the heat transfer coefficient can be scaled up proportional to D/sup -2/3/ (D = inside diameter of the fired heater tube). All flow conditions, liquid viscosities, and pipe inclinations relevant to the demonstration plant have indicated a slug flow regime in the slurry fired heater. The annular and stratified flow regimes should be avoided to minimize the potential for excessive pipe erosion and to decrease temperature gradients along the pipe cross section leading to coking and thermal stresses, respectively. Cold-flow studies in 3- and 6.75-in.-inside-diameter (ID) pipes were conducted to determine the effect of scale-up on flow regime, slug frequency, and slug dimensions. The developed model assumes that conduction heat transfer occurs through the liquid film surrounding the gas slug and laminar convective heat transfer to the liquid slug. A weighted average of these two heat transfer mechanisms gives a value for the average pipe heat transfer coefficient. The cold-flow work showed a decrease in the observed slug frequency between the 3- and 6.75-ID pipes. Data on the ratio of gas to liquid slug length in the 6.75-in. pipe are not yet complete, but are expected to yield generally lower values than those obtained in the 3-in. pipe; this will probably affect the scale-up to demonstration plant conditions. 5 references, 15 figures, 7 tables.

  15. ANALYSIS OF VENTING OF A RESIN SLURRY

    SciTech Connect

    Laurinat, J.; Hensel, S.

    2012-03-27

    A resin slurry venting analysis was conducted to address safety issues associated with overpressurization of ion exchange columns used in the Purex process at the Savannah River Site (SRS). If flow to these columns were inadvertently interrupted, an exothermic runaway reaction could occur between the ion exchange resin and the nitric acid used in the feed stream. The nitric acid-resin reaction generates significant quantities of noncondensable gases, which would pressurize the column. To prevent the column from rupturing during such events, rupture disks are installed on the column vent lines. The venting analysis models accelerating rate calorimeter (ARC) tests and data from tests that were performed in a vented test vessel with a rupture disk. The tests showed that the pressure inside the test vessel continued to increase after the rupture disk opened, though at a slower rate than prior to the rupture. Calculated maximum discharge rates for the resin venting tests exceeded the measured rates of gas generation, so the vent size was sufficient to relieve the pressure in the test vessel if the vent flow rate was constant. The increase in the vessel pressure is modeled as a transient phenomenon associated with expansion of the resin slurry/gas mixture upon rupture of the disk. It is postulated that the maximum pressure at the end of this expansion is limited by energy minimization to approximately 1.5 times the rupture disk burst pressure. The magnitude of this pressure increase is consistent with the measured pressure transients. The results of this analysis demonstrate the need to allow for a margin between the design pressure and the rupture disk burst pressure in similar applications.

  16. Pig in the Middle.

    ERIC Educational Resources Information Center

    Mills, Sophie

    2000-01-01

    Explores themes relating to human transition as they appear in "Charlotte's Web" and four other stories using pigs as a subject. Discusses the motifs common to all these texts that recur in the film "Babe." Considers how the cycle of life and death is ceaseless, and pigs symbolize the necessary transitions that people must all…

  17. Development of Syringe/Bottle Hybrids for Sampling Slurries

    SciTech Connect

    Coleman, C.J.

    1998-01-08

    A convenient and effective sample bottle system based on simple modifications of disposable plastic syringes and bottles has been devised and tested for slurry samples. Syringe/ bottle hybrids (hereafter referred to as syringe bottles) have the convenience of regular flat-bottom bottles with screw cap closures. In addition, the syringe imparts a sliding and adjustable bottom to the bottle that forces the entire contents from the bottle. The system was designed especially to collect samples for high temperature work-ups of DWPF slurry samples. The syringe bottles together with fixed-bottom sample vial inserts would provide the DWPF with convenient and reliable methods for dealing with slurry samples.

  18. Preparing polymeric matrix composites using an aqueous slurry technique

    NASA Technical Reports Server (NTRS)

    Johnston, Norman J. (Inventor); Towell, Timothy W. (Inventor)

    1993-01-01

    An aqueous process was developed to prepare a consolidated composite laminate from an aqueous slurry. An aqueous poly(amic acid) surfactant solution was prepared by dissolving a poly(amic acid) powder in an aqueous ammonia solution. A polymeric powder was added to this solution to form a slurry. The slurry was deposited on carbon fiber to form a prepreg which was dried and stacked to form a composite laminate. The composite laminate was consolidated using pressure and was heated to form the polymeric matrix. The resulting composite laminate exhibited high fracture toughness and excellent consolidation.

  19. Cysticercosis in the pig.

    PubMed

    de Aluja, A S

    2008-01-01

    Taenia solium cysticercosis is still an important parasitosis in rural pigs in many developing countries, México among them. The main causes for the persistence of this condition are lack of hygiene in the rural communities, lack of education of the animal owners, lack of control in the trade of pigs and their meat and lack of conscientious meat inspection. The pig production systems in the marginated areas of Mexico are briefly mentioned and it is stressed that among the important reasons for the persistence of the reproductive cycle of Taenia solium is the fact that appropriate toilet facilities in village dwellings are not mandatory. The diagnostic methods of cysticercosis in the living pigs and in their meat are discussed and the degenerative stages of the larvae as well as methods to test their viability are explained. The treatment of infected pigs and their meat is discussed. Recommendations for control programmes are given.

  20. Chemical Hydride Slurry for Hydrogen Production and Storage

    SciTech Connect

    McClaine, Andrew W

    2008-09-30

    The purpose of this project was to investigate and evaluate the attractiveness of using a magnesium chemical hydride slurry as a hydrogen storage, delivery, and production medium for automobiles. To fully evaluate the potential for magnesium hydride slurry to act as a carrier of hydrogen, potential slurry compositions, potential hydrogen release techniques, and the processes (and their costs) that will be used to recycle the byproducts back to a high hydrogen content slurry were evaluated. A 75% MgH2 slurry was demonstrated, which was just short of the 76% goal. This slurry is pumpable and storable for months at a time at room temperature and pressure conditions and it has the consistency of paint. Two techniques were demonstrated for reacting the slurry with water to release hydrogen. The first technique was a continuous mixing process that was tested for several hours at a time and demonstrated operation without external heat addition. Further work will be required to reduce this design to a reliable, robust system. The second technique was a semi-continuous process. It was demonstrated on a 2 kWh scale. This system operated continuously and reliably for hours at a time, including starts and stops. This process could be readily reduced to practice for commercial applications. The processes and costs associated with recycling the byproducts of the water/slurry reaction were also evaluated. This included recovering and recycling the oils of the slurry, reforming the magnesium hydroxide and magnesium oxide byproduct to magnesium metal, hydriding the magnesium metal with hydrogen to form magnesium hydride, and preparing the slurry. We found that the SOM process, under development by Boston University, offers the lowest cost alternative for producing and recycling the slurry. Using the H2A framework, a total cost of production, delivery, and distribution of $4.50/kg of hydrogen delivered or $4.50/gge was determined. Experiments performed at Boston

  1. New-Generation Sealing Slurries For Borehole Injection Purposes

    NASA Astrophysics Data System (ADS)

    Stryczek, Stanisław; Gonet, Andrzej; Wiśniowski, Rafał; Złotkowski, Albert

    2015-12-01

    The development of techniques and technologies thanks to which parameters of the ground medium can be modified makes specialists look for new recipes of geopolymers - binders for the reinforcing and sealing of unstable and permeable grounds. The sealing slurries are expected to meet a number of strict requirements, therefore it is important to find new admixtures and additives which could modify the fresh and hardened slurry. Special attention has been recently paid to the fluid ash - a by-product of the combustion of hard coals. However, the use of this additive is associated with the application of appropriate superplastifier. Laboratory analyses of rheological parameters of fresh sealing slurries and the ways of improving their liquidity by a properly selected third-generation superplastifier are presented in the paper. The slurries were based on Portland cement CEM I, milled granulated large-furnace slag and fly ash from fluidized-bed combustion of hard coal.

  2. Economics of a commercial slurry-phase biological treatment process

    SciTech Connect

    Jerger, D.E.; Woodhull, P.M.

    1995-12-31

    Slurry-phase bioremediation is an engineered process for treating contaminated soils or sludges in a slurry of water at 10 to 40% solids. Slurry-phase treatment relies on the mobilization of contaminants to the aqueous phase, where they are susceptible to microbial degradation. The mobilization or dissolution step can be the result of either microbial or physical/chemical action. Operating parameters are maintained to provide optimal conditions for biological treatment of the contaminants. OHM Remediation Services Corp. has completed the full-scale slurry-phase biological treatment of 10,500 yd{sup 3} of Resource Conservation and Recovery Act-K001 wastes at the Southeastern Wood Preserving Superfund site in Canton, Mississippi. The polycyclic aromatic hydrocarbon (PAH) concentrations in the untreated material ranged from 8,000 mg/kg to 12,000 mg/kg dry-weight. A 95% reduction in total PAH concentration was achieved following treatment.

  3. Thermal Performance of Microencapsulated Phase Change Material Slurry

    DTIC Science & Technology

    2008-03-01

    tetradec- ane-containing microcapsules with an average size of 4.4 μm. Yamagishi et al. (1999) obtained empirical data for microencapsulated octadecane ob...MPCM slurry (90 – 150 μm). It should be noted that the mass of an average microcapsule is equal to the mass of microencapsulated PCM and the mass...ER D C TR -0 8 -4 Basic Research/Military Construction Thermal Performance of Microencapsulated Phase Change Material Slurry Jorge L

  4. Effective use of fly ash slurry as fill material.

    PubMed

    Horiuchi, S; Kawaguchi, M; Yasuhara, K

    2000-09-15

    A lot of effort has been put into increasing coal ash utilization; however, 50% of total amount is disposed of on land and in the sea. Several attempts have been reported recently concerning slurried coal fly ash use for civil engineering materials, such as for structural fill and backfill. The authors have studied this issue for more than 15 years and reported its potential for (1) underwater fills, (2) light weight backfills, and (3) light weight structural fills, through both laboratory tests and construction works. This paper is an overview of the results obtained for slurry, focusing on the following. (1) Coal fly ash reclaimed by slurry placement shows lower compressibility, higher ground density, and higher strength than by the other methods. This higher strength increases stability against liquefaction during earthquake. (2) Higher stability of the fly ash ground formed by slurry placement is caused by higher density and its self-hardening property. (3) Stability of fly ash reclaimed ground can be increased by increasing density and also by strength enhancement by cement addition. (4) Technical data obtained through a man-made island construction project shows the advantages of fly ash slurry in terms of mechanical properties such as higher stability against sliding failure, sufficient ground strength, and also in terms of cost saving. (5) Concentration in leachates from the placed slurry is lower than the Japanese environmental law. (6) In order to enlarge the fly ash slurry application toward a lightweight fill, mixtures of air foam, cement and fly ash were examined. Test results shows sufficient durability of this material against creep failure. This material was then used as lightweight structural fill around a high-rise building, and showed sufficient quality. From the above data, it can be concluded that coal fly ash slurry can be effectively utilized in civil engineering projects.

  5. Slurry burner for mixture of carbonaceous material and water

    DOEpatents

    Nodd, Dennis G.; Walker, Richard J.

    1987-01-01

    A carbonaceous material-water slurry burner includes a high pressure tip-emulsion atomizer for directing a carbonaceous material-water slurry into a combustion chamber for burning therein without requiring a support fuel or oxygen enrichment of the combustion air. Introduction of the carbonaceous material-water slurry under pressure forces it through a fixed atomizer wherein the slurry is reduced to small droplets by mixing with an atomizing air flow and directed into the combustion chamber. The atomizer includes a swirler located immediately adjacent to where the fuel slurry is introduced into the combustion chamber and which has a single center channel through which the carbonaceous material-water slurry flows into a plurality of diverging channels continuous with the center channel from which the slurry exits the swirler immediately adjacent to an aperture in the combustion chamber. The swirler includes a plurality of slots around its periphery extending the length thereof through which the atomizing air flows and by means of which the atomizing air is deflected so as to exert a maximum shear force upon the carbonaceous material-water slurry as it exits the swirler and enters the combustion chamber. A circulating coolant system or boiler feed water is provided around the periphery of the burner along the length thereof to regulate burner operating temperature, eliminate atomizer plugging, and inhibit the generation of sparklers, thus increasing combustion efficiency. A secondary air source directs heated air into the combustion chamber to promote recirculation of the hot combustion gases within the combustion chamber.

  6. Polishing slurry induced surface haze on phosphate laser glasses

    SciTech Connect

    Suratwala, T I; Miller, P E; Ehrmann, P R; Steele, R A

    2004-03-12

    The effects of residual polishing slurry on the surface topology of highly-polished, Nd-doped metaphosphate laser glasses are reported. Glass samples were pitched polished using cerium oxide or zirconium oxide slurry at different pHs and then washed by different methods that allowed varying amounts of residual slurry to ''dry'' on the surface. Upon re-washing with water, some of the samples showed surface haze (scatter), which scaled with the amount of residual slurry. Profilometry measurements showed that the haze is the result of shallow surface pits (100 nm - 20 {micro}m wide x {approx}15 nm deep). Chemical analyses of material removed during rewashing, confirmed the removal of glass components as well as the preferential removal of modifier ions (e.g. K{sup 1+} and Mg{sup 2+}). The surface pits appear to result from reaction of the glass with condensed liquid at the slurry particle-glass interface that produces water-soluble phosphate products that dissolves away with subsequent water contact. Aggressive washing, to remove residual slurry immediately following polishing, can minimize surface haze on phosphate glasses. It is desirable to eliminate haze from glass used in high-peak-power lasers, since it can cause scatter-induced optical modulation that can cause damage to downstream optics.

  7. Testing of high temperature coal slurry pump packings

    SciTech Connect

    Hao, B.R.

    1982-12-01

    This report presents the results of a test program of packing designs and materials for high temperature coal slurry plunger pump services. The work was conducted to support the investigations and development of reliable and cost-effective reciprocating coal slurry pumps for future coal liquefaction process application. The short-term objectives were to screen, test and evaluate the state-of-the-art, commercially available packing designs and materials for the coal slurry feed pumps at the coal liquefaction pilot plants. Four major tasks were completed: failure analysis of slurry feed pumps packing components; selection of commercial packing designs and materials for testing; laboratory testing of high temperature coal slurry pump packings; and field testing of selected coalslurry pump packings. The results are presented. The primary root causes of the packing failures experienced at the pilot plants were identified as: insufficient packing lubrication, ineffective plunger flushing, unstable plunger alignment conditions of the pump, packing material incompatible to slurry and solvent, and undesirable packing installation, start-up, standby, and maintenance.

  8. Roles of additives and surface control in slurry atomization

    SciTech Connect

    Tsai, S.C.

    1992-01-01

    This project studies the rheology and airblast atomization of micronized coal slurries. Its major objectives are (1) to promote further understanding of the mechanisms and the roles of additives in airblast atomization of coal water slurry (CWS), and (2) to investigate the impacts of coal particle surface properties and interparticle forces on CWS rheology. We have found that the flow behavior index (n) of a suspension (or slurry) is determined by the relative importance of the interparticle van der Waals attraction and the interparticle electrostatic repulsion. The interparticle attraction, measured by the Hamaker constant scaled to the thermal energy at 25[degrees]C (A/kT), causes particle aggregation, which breaks down at high shear rates, and thus leads to slurry pseudoplastic behavior (n< 1). At a constant particle volume fraction and surface charge density (qualitatively measured by the zeta potential in deionized water), n decreases linearly as A/kT increases. The relative viscosity of the pseudoplastic suspension with respect to that of the suspending liquid is found to be independent of particle density and correlate well with the particle Peclet number which equals the particle diffusional relaxation time multiplied by shear rate. Specifically, the relative viscosities of the pseudoplastic glycerol/water coal slurry and the ethylene glycol/glycerol sand slurry, at same volume fractions as well as similar particle size distributions and liquid viscosities, as functions of the particle Peclet number fall along the same line.

  9. Implications of the Differential Toxicological Effects of III-V Ionic and Particulate Materials for Hazard Assessment of Semiconductor Slurries.

    PubMed

    Jiang, Wen; Lin, Sijie; Chang, Chong Hyun; Ji, Zhaoxia; Sun, Bingbing; Wang, Xiang; Li, Ruibin; Pon, Nanetta; Xia, Tian; Nel, André E

    2015-12-22

    Because of tunable band gaps, high carrier mobility, and low-energy consumption rates, III-V materials are attractive for use in semiconductor wafers. However, these wafers require chemical mechanical planarization (CMP) for polishing, which leads to the generation of large quantities of hazardous waste including particulate and ionic III-V debris. Although the toxic effects of micron-sized III-V materials have been studied in vivo, no comprehensive assessment has been undertaken to elucidate the hazardous effects of submicron particulates and released III-V ionic components. Since III-V materials may contribute disproportionately to the hazard of CMP slurries, we obtained GaP, InP, GaAs, and InAs as micron- (0.2-3 μm) and nanoscale (<100 nm) particles for comparative studies of their cytotoxic potential in macrophage (THP-1) and lung epithelial (BEAS-2B) cell lines. We found that nanosized III-V arsenides, including GaAs and InAs, could induce significantly more cytotoxicity over a 24-72 h observation period. In contrast, GaP and InP particulates of all sizes as well as ionic GaCl3 and InCl3 were substantially less hazardous. The principal mechanism of III-V arsenide nanoparticle toxicity is dissolution and shedding of toxic As(III) and, to a lesser extent, As(V) ions. GaAs dissolves in the cell culture medium as well as in acidifying intracellular compartments, while InAs dissolves (more slowly) inside cells. Chelation of released As by 2,3-dimercapto-1-propanesulfonic acid interfered in GaAs toxicity. Collectively, these results demonstrate that III-V arsenides, GaAs and InAs nanoparticles, contribute in a major way to the toxicity of III-V materials that could appear in slurries. This finding is of importance for considering how to deal with the hazard potential of CMP slurries.

  10. Nutrient digestibility and mass balance in laying hens fed a commercial or acidifying diet.

    PubMed

    Wu-Haan, W; Powers, W J; Angel, C R; Hale, C E; Applegate, T J

    2007-04-01

    The objectives of the current study were to evaluate the effect of an acidifying diet (gypsum) combined with zeolite and slightly reduced crude protein (R) vs. a control diet (C) on nutrient retention in laying hens and compare 3 approaches to estimating nutrient excretion from hens: 1) mass balance calculation (feed nutrients - egg nutrient), 2) use of an indigestible marker with analyzed feed and excreta nutrient content, and 3) an environmental chamber that allowed for capturing all excreted and volatilized nutrients. Hens (n = 640) were allocated randomly to 8 environmental chambers for 3-wk periods. Excreta samples were collected at the end of each trial to estimate apparent retention of N, S, P, and Ca. No diet effects on apparent retention of N were observed (53.44%, P > 0.05). Apparent retention of S, P, and Ca decreased in hens fed R diet (18.7, - 11.4, and 22.6%, respectively) compared with hens fed the C diet (40.7, 0.3, and 28.6%, respectively; P < 0.05). Total N excretion from hens fed the C and R diet was not different (1.16 g/hen/d); however, mass of chamber N remaining in excreta following the 3-wk period was less from hens fed the C diet (1.27 kg) than from hens fed the R diet (1.43 kg). Gaseous emissions of NH(3) over the 3-wk period from hens fed the C diet (0.74 kg per chamber) were greater than emissions from hens fed the R diet (0.45 kg). The 3-wk S excretion mass (estimated using the calculation, indigestible marker, and environmental chamber methods, respectively) was greater from hens fed the R diet (1.85, 1.54, and 1.27 kg, respectively) compared with hens fed the C diet (0.24, 0.20, and 0.14 kg, respectively). The 3-wk P excretion was similar between diets (0.68 kg). Results demonstrate that feeding the acidified diet resulted in decreased N emissions, but because of the acidulant fed, greatly increased S excretion and emissions.

  11. Sequestration of organic cations by acidified hepatic endocytic vesicles and implications for biliary excretion.

    PubMed

    Van Dyke, R W; Faber, E D; Meijer, D K

    1992-04-01

    A number of cationic amine drugs that are taken up by liver and excreted into bile may accumulate in acidified intracellular organelles such as lysosomes and endosomes. These studies were undertaken to assess directly the uptake and accumulation of three types of model organic cationic amines by endocytic vesicles, and the role of vesicle acidification in this process. Uptake of tubocurarine (TC), vecuronium and tributylmethylammonium (TBuMA) by purified rat liver multivesicular bodies (MVB) (prelysosomal endocytic vesicles) was dependent upon MgATP, time and drug concentration. After 60 min, 52 to 81% of MVB cation content was dependent upon vesicle acidification (due to an electrogenic proton pump), but not upon an interior positive vesicle membrane potential. Nineteen to 42% of MVB cation content appeared due to binding to MVB membranes or to internal lipoproteins. Vesicle-to-medium ATP-dependent apparent concentration ratios for these three cations were 3.3 to 51. MVB uptake of these cations resembled uptake of methylamine, a tertiary amine known to distribute across organellar membranes according to pH gradients. By contrast, MVB uptake of the lipophilic quaternary amine methyldeptropine was not dependent upon MgATP or on development of MVB pH or membrane potential gradients. In further studies, TC, vecuronium and TBuMA were rapidly taken up by the isolated perfused rat liver and excreted in bile. Exposure to 250 mciroM primaquin (which partially alkalinized acidic endosomes and lysosomes) reduced accumulation of [3H]vecuronium in a lysosomal fraction by 23%, decreased perfusate disappearance of TC and TBuMA, but not of vecuronium, and decreased biliary appearance of all three cations. These studies suggest that acidified intracellular organelles sequester certain organic cationic drugs, possibly via a drug/proton antiporter, and/or diffusion followed by intravesicular protonation and trapping of tertiary amines. However, attempts at partial displacement of

  12. Liquefaction of Douglas Fir wood slurries: titration of acids and anions in aqueous product and feed slurries

    SciTech Connect

    Davis, H.G.

    1981-03-01

    After hydrolytic pretreatment, wood slurries contain substantial amounts of organic acids. Additional acids are produced during the liquefaction step whether or not there is prehydrolysis. The acids have pH's in the range of about 3 to 5 and are easily titrated potentiometrically with sodium hydroxide. Anions present in neutralized slurry or in aqueous product can be titrated with hydrogen chloride solution with appropriate corrections for sulfate if present, and for excess titrant at the low pH of the endpoint.

  13. Slurry combustion. Volume 1, Text: Final report

    SciTech Connect

    Essenhigh, R.

    1993-06-21

    The project described in this Report was to investigate the possibility of using sorbent added to coal-water fuel (CWF) mixtures as a means of reducing SOX emissions when burning Ohio coal. The results are significantly encouraging, with SOX concentrations reduced by amounts ranging from 25% to 65%, depending on the sorbent type and the firing conditions, where one major condition identified was the residence time in the flame gases. With the sorbent-loaded slurrys, the trend generally showed increasing SO{sub 2} capture with increasing sorbent loading. There were significant differences between the two different mixture formulations, however: The calcite/No. 8-seam mixture showed significantly higher SO{sub 2} capture at all times (ranging from 45% to 65%) than did the dolomite/No. 5 seam mixture (ranging from 25% to 45%). If the successes so far achieved are not to be wasted, advantage should be taken of these encouraging results by extending the work at both the present scale to determine the other unknown factors controlling sorption efficiency, and at larger scale to start implementation in commercial systems.

  14. New technology improves cement-slurry design

    SciTech Connect

    1997-08-01

    A promising geothermal concession is located in a tea plantation on the island of Java. A drilling project was undertaken to evaluate and harness this resource for geothermal electricity generation. The program used two slimhole rigs to drill appraisal wells to establish the potential of the field. Geothermal wells present the most severe conditions to which cements are exposed. As a result, their performance requirements are among the most stringent. Geothermal cements are usually designed to provide at least 1,000 psi compressive strength and no more than 1.0-md water permeability. While casings with tight annular clearances require that good cementing practices be observed, they also create conditions that demand much greater care and control in slurry and procedure design than regular casing cementation. Free-water and thickening-time requirements are similar for geothermal and slimhole conditions, but the use of perlite and silica flour complicate the rheology required for geothermal wells. The paper describes liquid-cement premix, applications, laboratory testing, field pilot testing, and field operations.

  15. Technical Report on NETL's Non Newtonian Multiphase Slurry Workshop: A path forward to understanding non-Newtonian multiphase slurry flows

    SciTech Connect

    Edited by Guenther, Chris; Garg, Rahul

    2013-08-19

    The Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) sponsored a workshop on non-Newtonian multiphase slurry at NETL’s Morgantown campus August 19 and 20, 2013. The objective of this special two-day meeting of 20-30 invited experts from industry, National Labs and academia was to identify and address technical issues associated with handling non-Newtonian multiphase slurries across various facilities managed by DOE. Particular emphasis during this workshop was placed on applications managed by the Office of Environmental Management (EM). The workshop was preceded by two webinars wherein personnel from ORP and NETL provided background information on the Hanford WTP project and discussed the critical design challenges facing this project. In non-Newtonian fluids, viscosity is not constant and exhibits a complex dependence on applied shear stress or deformation. Many applications under EM’s tank farm mission involve non-Newtonian slurries that are multiphase in nature; tank farm storage and handling, slurry transport, and mixing all involve multiphase flow dynamics, which require an improved understanding of the mechanisms responsible for rheological changes in non-Newtonian multiphase slurries (NNMS). To discuss the issues in predicting the behavior of NNMS, the workshop focused on two topic areas: (1) State-of-the-art in non-Newtonian Multiphase Slurry Flow, and (2) Scaling up with Confidence and Ensuring Safe and Reliable Long-Term Operation.

  16. Pig production in the Solomon Islands. I. Village pig production.

    PubMed

    de Fredrick, D F

    1977-05-01

    In 181 villages in the Solomon Islands the pig: human ratio was 1:5-8 and the annual per capita pork consumption was 4-2 kg. Some communities did not keep pigs or eat pig meat. Sows weaned an average of 5-5 piglets per year and mean liveweight at 12 months of age was 28-4 kg. Most pigs were kept on the ground but some were housed in pens over the sea and very few lived in their owner's houses. Pigs were important in the social life of the people but proportionally fewer pigs were raised than in neighbouring Pacific countries.

  17. Nitrite addition to acidified sludge significantly improves digestibility, toxic metal removal, dewaterability and pathogen reduction

    NASA Astrophysics Data System (ADS)

    Du, Fangzhou; Keller, Jürg; Yuan, Zhiguo; Batstone, Damien J.; Freguia, Stefano; Pikaar, Ilje

    2016-12-01

    Sludge management is a major issue for water utilities globally. Poor digestibility and dewaterability are the main factors determining the cost for sludge management, whereas pathogen and toxic metal concentrations limit beneficial reuse. In this study, the effects of low level nitrite addition to acidified sludge to simultaneously enhance digestibility, toxic metal removal, dewaterability and pathogen reduction were investigated. Waste activated sludge (WAS) from a full-scale waste water treatment plant was treated at pH 2 with 10 mg NO2‑-N/L for 5 h. Biochemical methane potential tests showed an increase in the methane production of 28%, corresponding to an improvement from 247 ± 8 L CH4/kg VS to 317 ± 1 L CH4/kg VS. The enhanced removal of toxic metals further increased the methane production by another 18% to 360 ± 6 L CH4/kg VS (a total increase of 46%). The solids content of dewatered sludge increased from 14.6 ± 1.4% in the control to 18.2 ± 0.8%. A 4-log reduction for both total coliforms and E. coli was achieved. Overall, this study highlights the potential of acidification with low level nitrite addition as an effective and simple method achieving multiple improvements in terms of sludge management.

  18. Nitrite addition to acidified sludge significantly improves digestibility, toxic metal removal, dewaterability and pathogen reduction

    PubMed Central

    Du, Fangzhou; Keller, Jürg; Yuan, Zhiguo; Batstone, Damien J.; Freguia, Stefano; Pikaar, Ilje

    2016-01-01

    Sludge management is a major issue for water utilities globally. Poor digestibility and dewaterability are the main factors determining the cost for sludge management, whereas pathogen and toxic metal concentrations limit beneficial reuse. In this study, the effects of low level nitrite addition to acidified sludge to simultaneously enhance digestibility, toxic metal removal, dewaterability and pathogen reduction were investigated. Waste activated sludge (WAS) from a full-scale waste water treatment plant was treated at pH 2 with 10 mg NO2−-N/L for 5 h. Biochemical methane potential tests showed an increase in the methane production of 28%, corresponding to an improvement from 247 ± 8 L CH4/kg VS to 317 ± 1 L CH4/kg VS. The enhanced removal of toxic metals further increased the methane production by another 18% to 360 ± 6 L CH4/kg VS (a total increase of 46%). The solids content of dewatered sludge increased from 14.6 ± 1.4% in the control to 18.2 ± 0.8%. A 4-log reduction for both total coliforms and E. coli was achieved. Overall, this study highlights the potential of acidification with low level nitrite addition as an effective and simple method achieving multiple improvements in terms of sludge management. PMID:28004811

  19. The natural rehabilitation of an anthropogenically acidified tropical Lake: two decades of monitoring.

    PubMed

    Araújo, Cristiano V M; Cohin-de-Pinho, Salomão J; Chastinet, Carla B A; Machado, Sandro L; da Silva, Eduardo M

    2013-01-01

    The rehabilitation of a pond after approximately 20 years of strong acidified conditions due to industrial and domestic waste deposition in its catchment basin is reviewed. We describe in this study the acidification process that occurred in a tropical pond in Northeast Brazil (Dunas Lake), the rehabilitation plan for the pond and the subsequent monitoring conducted over two decades. After the contamination assessment by the late 80s, a rehabilitation plan was carried out in the early 90s, in which the contaminated soil and water have been removed and reduced, respectively. No further attempt to neutralize the water or any remediation has been carried out. A toxicity monitoring plan based on toxicity assays with the fish Poecilia reticulata was employed to verify the natural rehabilitation of the pond. The data on toxicity, pH, conductivity, sulphate and dissolved iron recorded from 1994 to 2010 were also compiled and discussed. The collected data in 2003 and 2004 indicated changes in water quality and from them complementary management actions, namely improvement in the containment plant, were conducted in 2005. Results for toxicity assays and pH results indicated interannual changes in the water quality similar to rainy-dry periods. Moving average approach using pH data clearly showed the recovery process of Dunas Lake as well as the importance of the containment plan to reduce the contamination. Finally, a summary of the recent situation after two decades of rehabilitation is provided.

  20. Treatment of Acidified Blood Using Reduced Osmolarity Mixed-Base Solutions

    PubMed Central

    Mason, Thomas G.; Kraut, Jeffrey A.

    2016-01-01

    We hypothesize that reduced osmolarity mixed-base (ROMB) solutions can potentially serve as customizable treatments for acidoses, going beyond standard solutions in clinical use, such as 1.0 M sodium bicarbonate. Through in silico quantitative modeling, by treating acidified canine blood using ROMB solutions, and by performing blood-gas and optical microscopy measurements in vitro, we demonstrate that ROMB solutions having a high proportion of a strong base, such as disodium carbonate or sodium hydroxide, can be effective in reducing carbon dioxide pressure PCO2 while raising pH and bicarbonate ion concentration without causing significant osmotic damage to red blood cells, which can occur during rapid administration of hypertonic solutions of weak bases. These results suggest that a ROMB solution, which is composed mostly of a strong base, could be administered in a safe and effective manner, when compared to a hypertonic solution of sodium bicarbonate. Because of the reduced osmolarity and the customizable content of strong base in ROMB solutions, this approach differs from prior approaches involving hypertonic solutions that only considered a single molar ratio of strong to weak base. Our calculations and measurements suggest that custom-tailored ROMB solutions merit consideration as potentially efficacious treatments for specific types of acidosis, particularly acute metabolic acidosis and acute respiratory acidosis. PMID:28082905

  1. Rheology and stability of acidified food emulsions treated with high pressure.

    PubMed

    Arora, Akshay; Chism, Grady W; Shellhammer, Thomas H

    2003-04-23

    The stability and rheology of acidified model oil-in-water emulsions (pH 3.6 +/- 0.1) were evaluated before and after high-pressure treatments. Varying concentrations of canola oil (0-50% w/w), whey protein isolate, polysorbate 60, soy lecithin (0.1-1.5% w/w each), and xanthan (0.0-0.2% w/w) were chosen. Exposure to high pressures (up to 800 MPa for 5 min at 30 degrees C) did not significantly affect the equivalent surface mean diameter D[3,2], flow behavior, and viscoelasticity of the whey protein isolate and polysorbate 60-stabilized emulsions. Pressure treatments had negligible effects on emulsion stability in these systems, except when xanthan (0.2% w/w) was present in which pressure improved the stability of polysorbate 60-stabilized emulsions. Soy lecithin-stabilized emulsions had larger mean particles sizes and lower emulsion volume indices than the others, indicating potential instability, and application of pressure further destabilized these emulsions.

  2. Corrosion Fatigue Behavior of 316LN SS in Acidified Sodium Chloride Solution at Applied Potential

    NASA Astrophysics Data System (ADS)

    Poonguzhali, A.; Pujar, M. G.; Mallika, C.; Mudali, U. Kamachi

    2015-05-01

    The influence of acidified 1 M NaCl solution by addition of 2 ml/L of HCl on the cyclic plastic deformation of AISI Type 316LN SS containing 0.07 wt.% and 0.22 wt.% N was investigated as a function of the applied potentials. The corrosion fatigue (CF) behavior of stainless steel (SS) was explained vis-a-vis the dislocation behavior, the propensity to form microcracks, and the evolution of the current transients based on the studies carried out at both room-temperature and boiling conditions. CF experiments were conducted using round tensile specimens at a stress ratio of 0.5 and a frequency of 0.1 Hz. Two different kinds of damage mechanisms were observed (I) the damage mechanism in the stable-passive state was correlated with the localization of the anodic dissolution due to a depassivation-repassivation process, whereas (II) the cyclic stress induced pitting corrosion in the metastable pitting state, which resulted in formation of microcracks. The study of the microcracking process and its evolution is a key to the physical mechanism by which the fatigue life of stainless steels would be affected in an aqueous corrosive solution under the applied potential.

  3. Transplanted aquatic mosses for monitoring trace metal mobilization in acidified streams of the Vosges Mountains, France

    SciTech Connect

    Mersch, J.; Guerold, F.; Rousselle, P.; Pihan, J.C. )

    1993-08-01

    As a result of acid depositions, trace metals are mobilized from the soils to the aquatic environment. Especially in poorly mineralized waters, elevated metal concentrations may rapidly have adverse effects on aquatic organisms. In particular, it has been shown that aluminium, a key element in the acidification process, is a toxic cofactor for fish and other biota. An accurate assessment of this specific form of water pollution may not be possible when only based on analyses of single water samples. On the one hand, water metal concentrations are often close to the detection limit of usual analytical techniques, and on the other hand, levels in acidified streams undergo strong temporal variations caused by acid pulses following meteorological events such as heavy rainfall and snowmelt. Compared to water analyses, indirect monitoring methods provide undeniable advantages for assessing water contamination. Aquatic bryophytes, in particular, have been regarded as interesting indicator organisms for trace metal pollution. However, their use has mainly been restricted to the lower course of streams for evaluating the impact of industrial discharges. The purpose of this study was to test the suitability of transplanted aquatic mosses for monitoring aluminium and four other trace metals (copper, iron, lead and zinc) in the particular context of acidifed streams draining a forested headwater catchment. 15 refs., 2 figs., 2 tabs.

  4. Experiments and modeling of variably permeable carbonate reservoir samples in contact with CO₂-acidified brines

    SciTech Connect

    Smith, Megan M.; Hao, Yue; Mason, Harris E.; Carroll, Susan A.

    2014-12-31

    Reactive experiments were performed to expose sample cores from the Arbuckle carbonate reservoir to CO₂-acidified brine under reservoir temperature and pressure conditions. The samples consisted of dolomite with varying quantities of calcite and silica/chert. The timescales of monitored pressure decline across each sample in response to CO₂ exposure, as well as the amount of and nature of dissolution features, varied widely among these three experiments. For all samples cores, the experimentally measured initial permeability was at least one order of magnitude or more lower than the values estimated from downhole methods. Nondestructive X-ray computed tomography (XRCT) imaging revealed dissolution features including “wormholes,” removal of fracture-filling crystals, and widening of pre-existing pore spaces. In the injection zone sample, multiple fractures may have contributed to the high initial permeability of this core and restricted the distribution of CO₂-induced mineral dissolution. In contrast, the pre-existing porosity of the baffle zone sample was much lower and less connected, leading to a lower initial permeability and contributing to the development of a single dissolution channel. While calcite may make up only a small percentage of the overall sample composition, its location and the effects of its dissolution have an outsized effect on permeability responses to CO₂ exposure. The XRCT data presented here are informative for building the model domain for numerical simulations of these experiments but require calibration by higher resolution means to confidently evaluate different porosity-permeability relationships.

  5. The behavior of rare earth elements in naturally and anthropogenically acidified waters

    USGS Publications Warehouse

    Wood, Scott A.; Gammons, Christopher H.; Parker, Stephen R.

    2006-01-01

    In this paper, the behavior of rare earth elements (REE) in a watershed impacted by acid-mine drainage (Fisher Creek, Montana) is compared to that in a volcanically acidified watershed (Rio Agrio and Lake Caviahue, Argentina). The REE behave conservatively in acidic waters with pH values less than approximately 5.5. However, above pH 5.5, REE concentrations are controlled by adsorption onto or co-precipitation with a variety of Fe or Al oxyhydroxides. The heavy REE partition to a greater extent into the solid phase than the light REE as pH rises above 6. Concentrations of REE exhibit diel (24-h) cycling in waters that were initially acidic, but have become neutralized downstream. In Fisher Creek, at the most downstream sampling station investigated (pH 6.8), concentrations of dissolved REE were 190–840% higher in the early morning versus the late afternoon. This cycling can be related to temperature-dependent, cyclic adsorption–desorption of REE onto hydrous ferric or aluminum oxide or both. Similar but gentler diel cycling of the REE was found at Rio Agrio. The existence of such cycling has important ramifications for the study of REE in natural waters.

  6. Trichodesmium’s strategies to alleviate phosphorus limitation in the future acidified oceans.

    PubMed

    Spungin, Dina; Berman-Frank, Ilana; Levitan, Orly

    2014-06-01

    Global warming may exacerbate inorganic nutrient limitation, including phosphorus (P), in the surface waters of tropical oceans that are home to extensive blooms of the marine diazotrophic cyanobacterium, Trichodesmium. We examined the combined effects of P limitation and pCO(2), forecast under ocean acidification scenarios, on Trichodesmium erythraeum IMS101 cultures. We measured nitrogen acquisition,glutamine synthetase activity, C uptake rates, intracellular Adenosine Triphosphate (ATP) concentration and the pool sizes of related key proteins. Here, we present data supporting the idea that cellular energy re-allocation enables the higher growth and N(2) fixation rates detected in Trichodesmium cultured under high pCO(2). This is reflected in altered protein abundance and metabolic pools. Also modified are particulate organic carbon and nitrogen production rates,enzymatic activities, and cellular ATP concentrations. We suggest that adjusting these cellular pathways to changing environmental conditions enables Trichodesmium to compensate for low P availability and to thrive in acidified oceans. Moreover, elevated pCO(2) could provide Trichodesmium with a competitive dominance that would extend its niche, particularly in P-limited regions of the tropical and subtropical oceans.

  7. Extracellular DNA Acidifies Biofilms and Induces Aminoglycoside Resistance in Pseudomonas aeruginosa.

    PubMed

    Wilton, Mike; Charron-Mazenod, Laetitia; Moore, Richard; Lewenza, Shawn

    2015-11-09

    Biofilms consist of surface-adhered bacterial communities encased in an extracellular matrix composed of DNA, exopolysaccharides, and proteins. Extracellular DNA (eDNA) has a structural role in the formation of biofilms, can bind and shield biofilms from aminoglycosides, and induces antimicrobial peptide resistance mechanisms. Here, we provide evidence that eDNA is responsible for the acidification of Pseudomonas aeruginosa planktonic cultures and biofilms. Further, we show that acidic pH and acidification via eDNA constitute a signal that is perceived by P. aeruginosa to induce the expression of genes regulated by the PhoPQ and PmrAB two-component regulatory systems. Planktonic P. aeruginosa cultured in exogenous 0.2% DNA or under acidic conditions demonstrates a 2- to 8-fold increase in aminoglycoside resistance. This resistance phenotype requires the aminoarabinose modification of lipid A and the production of spermidine on the bacterial outer membrane, which likely reduce the entry of aminoglycosides. Interestingly, the additions of the basic amino acid L-arginine and sodium bicarbonate neutralize the pH and restore P. aeruginosa susceptibility to aminoglycosides, even in the presence of eDNA. These data illustrate that the accumulation of eDNA in biofilms and infection sites can acidify the local environment and that acidic pH promotes the P. aeruginosa antibiotic resistance phenotype.

  8. Alterations of Fractures in Carbonate Rocks by CO2-Acidified Brines.

    PubMed

    Deng, Hang; Fitts, Jeffrey P; Crandall, Dustin; McIntyre, Dustin; Peters, Catherine A

    2015-08-18

    Fractures in geological formations may enable migration of environmentally relevant fluids, as in leakage of CO2 through caprocks in geologic carbon sequestration. We investigated geochemically induced alterations of fracture geometry in Indiana Limestone specimens. Experiments were the first of their kind, with periodic high-resolution imaging using X-ray computed tomography (xCT) scanning while maintaining high pore pressure (100 bar). We studied two CO2-acidified brines having the same pH (3.3) and comparable thermodynamic disequilibrium but different equilibrated pressures of CO2 (PCO2 values of 12 and 77 bar). High-PCO2 brine has a faster calcite dissolution kinetic rate because of the accelerating effect of carbonic acid. Contrary to expectations, dissolution extents were comparable in the two experiments. However, progressive xCT images revealed extensive channelization for high PCO2, explained by strong positive feedback between ongoing flow and reaction. The pronounced channel increasingly directed flow to a small region of the fracture, which explains why the overall dissolution was lower than expected. Despite this, flow simulations revealed large increases in permeability in the high-PCO2 experiment. This study shows that the permeability evolution of dissolving fractures will be larger for faster-reacting fluids. The overall mechanism is not because more rock dissolves, as would be commonly assumed, but because of accelerated fracture channelization.

  9. Development of a Model for Planning Transportation and Application of Digested Slurry to Farmlands

    NASA Astrophysics Data System (ADS)

    Yamaoka, Masaru; Nakamura, Masato; Aihara, Hideki; Shimizu, Natsuki; Yuyama, Yoshito

    The authors developed a model for planning the transportation and application of digested slurry to farmlands as a fertilizer. The model requires the following parameters, daily production of the digested slurry, concentrations of fertilizer elements in the digested slurry, distances from the plant to each field where the slurry will be applied and application loads of slurry for each field. According to the data, the model simulates daily workloads for transportation of digested slurry from the plant to the fields by a vacuum truck and application of slurry to each field with a spreader. The model calculates the daily changes in digested slurry storage at the plant. Validity of the model was confirmed by data obtained from a pilot scale plant. The model is a useful tool for planning the transportation and application of digested slurry to farmland as a fertilizer.

  10. Hygienic aspects of livestock manure management and biogas systems operated by small-scale pig farmers in Vietnam.

    PubMed

    Huong, Luu Quynh; Madsen, Henry; Anh, Le Xuan; Ngoc, Pham Thi; Dalsgaard, Anders

    2014-02-01

    Biogas digesters are widely promoted and increasingly used to treat and generate gas from pig slurry worldwide. The objective of this study was to describe manure management practices with focus on biogas digestion among small scale pig farmers in Hue (50 farmers) and Hanoi (96 farmers) and to assess fecal contamination levels in biogas effluent. Results showed that 84% of the farmers in Hanoi and 42% in Hue used both pig slurry and human excreta for biogas production. Biogas digestion only reduced E. coli concentrations by 1 to 2 log units to 3.70 ± 0.84 Escherichia coli (log10) cfu/ml on average in effluent as compared with raw slurry. Biogas effluent was commonly used to fertilize vegetables or discharged directly into the garden or aquatic recipients. Reduced problems with bad smells and flies were reported as main reasons for establishing a biogas digester. Further studies are needed to assess human and animal health hazards associated with the discharge and use of biogas effluent from small-scale biogas systems.

  11. Elevated aluminium concentration in acidified headwater streams lowers aquatic hyphomycete diversity and impairs leaf-litter breakdown.

    PubMed

    Baudoin, J M; Guérold, F; Felten, V; Chauvet, E; Wagner, P; Rousselle, P

    2008-08-01

    Aquatic hyphomycetes play an essential role in the decomposition of allochthonous organic matter which is a fundamental process driving the functioning of forested headwater streams. We studied the effect of anthropogenic acidification on aquatic hyphomycetes associated with decaying leaves of Fagus sylvatica in six forested headwater streams (pH range, 4.3-7.1). Non-metric multidimensional scaling revealed marked differences in aquatic hyphomycete assemblages between acidified and reference streams. We found strong relationships between aquatic hyphomycete richness and mean Al concentration (r = -0.998, p < 0.0001) and mean pH (r = 0.962, p < 0.002), meaning that fungal diversity was severely depleted in acidified streams. By contrast, mean fungal biomass was not related to acidity. Leaf breakdown rate was drastically reduced under acidic conditions raising the issue of whether the functioning of headwater ecosystems could be impaired by a loss of aquatic hyphomycete species.

  12. Complex responses of intertidal molluscan embryos to a warming and acidifying ocean in the presence of UV radiation.

    PubMed

    Davis, Andrew R; Coleman, Daniel; Broad, Allison; Byrne, Maria; Dworjanyn, Symon A; Przeslawski, Rachel

    2013-01-01

    Climate change and ocean acidification will expose marine organisms to synchronous multiple stressors, with early life stages being potentially most vulnerable to changing environmental conditions. We simultaneously exposed encapsulated molluscan embryos to three abiotic stressors-acidified conditions, elevated temperate, and solar UV radiation in large outdoor water tables in a multifactorial design. Solar UV radiation was modified with plastic filters, while levels of the other factors reflected IPCC predictions for near-future change. We quantified mortality and the rate of embryonic development for a mid-shore littorinid, Bembicium nanum, and low-shore opisthobranch, Dolabrifera brazieri. Outcomes were consistent for these model species with embryos faring significantly better at 26°C than 22°C. Mortality sharply increased at the lowest temperature (22°C) and lowest pH (7.6) examined, producing a significant interaction. Under these conditions mortality approached 100% for each species, representing a 2- to 4-fold increase in mortality relative to warm (26°C) non-acidified conditions. Predictably, development was more rapid at the highest temperature but this again interacted with acidified conditions. Development was slowed under acidified conditions at the lowest temperature. The presence of UV radiation had minimal impact on the outcomes, only slowing development for the littorinid and not interacting with the other factors. Our findings suggest that a warming ocean, at least to a threshold, may compensate for the effects of decreasing pH for some species. It also appears that stressors will interact in complex and unpredictable ways in a changing climate.

  13. Mycotoxic nephropathy in pigs*

    PubMed Central

    Elling, F.; Møller, T.

    1973-01-01

    In Denmark a nephropathy in pigs characterized by tubular atrophy and interstitial fibrosis has been identified frequently during the last 5 decades in the course of meat inspection in slaughterhouses. The disease was first described by Larsen, who recognized the connexion between feeding mouldy rye to pigs and the development of the nephropathy. In this study kidneys were examined from 19 pigs coming from a farm with an outbreak of nephropathy. The barley fed to the pigs was contaminated with the mycotoxin ochratoxin A. Histological examination revealed different degrees of change ranging from slight regressive changes in the tubular epithelium and periglomerular and interstitial fibrosis to tubular atrophy, thickened basement membranes, glomerular sclerosis, and marked fibrosis. These differences were considered to be due to differences in the length of time of exposure to the mouldy barley and differences in the amount of mycotoxin consumed by the individual pig. However, it will be necessary to carry out experiments using crystalline ochratoxin A in order to prove such a relationship. Mycotoxins have also been suggested as etiological factors in Balkan nephropathy in man, which in the initial stages is characterized by tubular lesions similar to those seen in mycotoxic nephropathy in pigs. ImagesFig. 1Fig. 2Fig. 7Fig. 8Fig. 9Fig. 3Fig. 4Fig. 5Fig. 6Fig. 10Fig. 11 PMID:4546872

  14. Anthropogenic oligotrophication via liming: Long-term phosphorus trends in acidified, limed, and neutral reference lakes in Sweden.

    PubMed

    Hu, Qian; Huser, Brian J

    2014-01-01

    Restoration of acidified lakes by liming does not, in many cases, improve productivity to a pre-acidified state. We hypothesize that the poor recovery detected in many of these lakes is due to constrained in-lake phosphorous (P) cycling caused by enhanced precipitation of metals in higher pH, limed waters. Long-term (1990-2012) data for 65 limed, circum-neutral (pH 6-8), and acidified lakes in Sweden were analyzed to determine trends for P and potential drivers of these trends. Limed lakes not only had lower mean values and stronger decreasing trends for total P than non-limed lakes, but they also had the highest percentage of decreasing trends (85 %). A P release factor (Hypolimnetic P/Epilimnetic P) was developed to elucidate differences in internal P cycling between lake groups. Consistently, lower P release factors in limed lakes show limitation of internal P cycling during summer months that may be a factor limiting P bioavailability and thus productivity of these systems.

  15. Effect of Groove Pattern of Chemical Mechanical Polishing Pad on Slurry Flow Behavior

    NASA Astrophysics Data System (ADS)

    Yamazaki, Tsutomu; Doi, Toshiro K.; Uneda, Michio; Kurokawa, Syuhei; Ohnishi, Osamu; Seshimo, Kiyoshi; Aida, Hideo

    2012-05-01

    In chemical mechanical polishing (CMP), the slurry flow behavior on the polishing pad is very important both for improving polishing effectiveness and for reducing the slurry consumption. In this study, we aim to evaluate two types of CMP pad that have unique special groove patterns, slurry outflow and inflow pads, for controlling the slurry flow behavior. We describe the effect of the groove patterns on the slurry flow behavior observed using images recorded using a high-speed digital camera. The results of the study indicate several advantages of the proposed pads over the conventional pads from the viewpoint of slurry flow behavior.

  16. Novel techniques for slurry bubble column hydrodynamics

    SciTech Connect

    Dudukovic, M.P.

    1999-05-14

    The objective of this cooperative research effort between Washington University, Ohio State University and Exxon Research Engineering Company was to improve the knowledge base for scale-up and operation of slurry bubble column reactors for syngas conversion and other coal conversion processes by increased reliance on experimentally verified hydrodynamic models. During the first year (July 1, 1995--June 30, 1996) of this three year program novel experimental tools (computer aided radioactive particle tracking (CARPT), particle image velocimetry (PIV), heat probe, optical fiber probe and gamma ray tomography) were developed and tuned for measurement of pertinent hydrodynamic quantities, such as velocity field, holdup distribution, heat transfer and bubble size. The accomplishments were delineated in the First Technical Annual Report. The second year (July, 1996--June 30, 1997) was spent on further development and tuning of the novel experimental tools (e.g., development of Monte Carlo calibration for CARPT, optical probe development), building up the hydrodynamic data base using these tools and comparison of the two techniques (PIV and CARPT) for determination of liquid velocities. A phenomenological model for gas and liquid backmixing was also developed. All accomplishments were summarized in the Second Annual Technical Report. During the third and final year of the program (July 1, 1997--June 30, 1998) and during the nine months no cost extension, the high pressure facility was completed and a set of data was taken at high pressure conditions. Both PIV, CT and CARPT were used. More fundamental hydrodynamic modeling was also undertaken and model predictions were compared to data. The accomplishments for this period are summarized in this report.

  17. Preparation and combustion of high ash coal tailing slurry

    SciTech Connect

    Zhang Ziping; Zhang Wenfu; Fu Xiaoheng; Wang Zuna; Li Hui

    1998-12-31

    Flotation tailings from a coal preparation plant are known for their high ash, low heating value, high moisture content even after thickening and filtration, and difficult handability. However, they can be easily converted into a slurry fuel for boilers. Two flotation tailings, containing ash of 31.89% and 41.87% respectively, have been converted into slurry fuel with the following properties: solid content being 70.4% and 74.4% respectively; low heating value, 13,694kj/kg and 10,970kj/kg; and viscosity, 379 mPa.s and 180 mPa.s at a shear rate of 100s{sup {minus}1}. An eccentric slant jet coal slurry burner was installed at the boiler. Slurry atomizing nozzle operated at low pressure. Both slurries gave stable combustion without supporting fuel under the condition of cool air supply. A new way of flotation tailing utilization was demonstrated. China has more than 200 coal preparation plants washing more than 300 million tons of coal annually. These preparation plants generate more than 10 million tons of tailing annually, most of which is not currently being used, causing great environmental pollution and waste management difficulties for the enterprises. Comprehensive utilization of coal washer tailings is one of the key issues of environmental protection and energy saving in China.

  18. Roles of additives and surface control in slurry atomization

    SciTech Connect

    Tsai, S.C.

    1990-01-01

    This report focuses on the effects of interparticle forces on the rheology and airblast atomization of micronized coal water slurry (CWS). We found that the CWS flow behavior index is determined by the relative importance of the interparticle van der Waals attraction and the interparticle electrostatic repulsion. The former intensifies as the Hamaker constant increases and the interparticle distance reduces while the latter increases as the particle surface charge density increases. The interparticle attraction causes particle aggregation, which breaks down at high shear rates, and thus leads to slurry pseudoplastic behavior. In contrast, the interparticle repulsion prevents particle aggregation and thus leads to Newtonian behavior. Both atomized at low atomizing air pressures (less than 270 kPa) using twin-fluid jet atomizers of various distributor designs. We found that the atomized drop sizes of micronized coal water slurries substantially decrease as the atomizing air pressure exceeds a threshold value. The effects of coal volume fraction, coal particle surface charge, liquid composition and liquid viscosity on slurry atomization can be accounted for by their effects on slurry rheology. 26 refs.

  19. Redox Potential as a Means to Control the Treatment of Slurry to Lower H2S Emissions

    PubMed Central

    Hjorth, Maibritt; Pedersen, Christina Ø; Feilberg, Anders

    2012-01-01

    Slurry can be oxidized to eliminate undesirable emissions, including malodorous hydrogen sulfide (H2S). However, it is difficult to assess the optimal amount of oxidizing agent required. In this study, one cow and one pig manure, each in three particle size ranges were oxidized with 0–350 mg ozone/L manure. Redox and H2S concentration were measured continuously. During ozonation the manures gave equivalent redox potential curves. A relatively rapid rise in redox potential was observed within a range of −275 mV to −10 mV, with all manures changing as a minimum from −200 mV to −80 mV. The gaseous H2S emissions were decreased by 99.5% during the redox increase (−200 mV to −80 mV). This is attributed to H2S oxidation by ozone and oxygen, and is not due to H2S deprotonation or gas flushing. By identifying the initiation of the final redox level following the rise, the amount of ozone required to remove H2S from the manure samples was estimated to be in the range of 6–24 mg O3/L manure, depending on the type of manure. Hence, continuous monitoring of redox potential (termination of the redox rise) during the oxidation treatment is a simple method of achieving cost-effective minimization of H2S emissions from slurry. PMID:22778588

  20. Fate and transport of antimicrobials and antimicrobial resistance genes in soil and runoff following land application of swine manure slurry.

    PubMed

    Joy, Stacey R; Bartelt-Hunt, Shannon L; Snow, Daniel D; Gilley, John E; Woodbury, Bryan L; Parker, David B; Marx, David B; Li, Xu

    2013-01-01

    Due to the use of antimicrobials in livestock production, residual antimicrobials and antimicrobial resistance genes (ARGs) could enter the environment following the land application of animal wastes and could further contaminate surface and groundwater. The objective of this study was to determine the effect of various manure land application methods on the fate and transport of antimicrobials and ARGs in soil and runoff following land application of swine manure slurry. Swine manure slurries were obtained from facilities housing pigs that were fed chlortetracyline, tylosin or bacitracin and were land applied via broadcast, incorporation, and injection methods. Three rainfall simulation tests were then performed on amended and control plots. Results show that land application methods had no statistically significant effect on the aqueous concentrations of antimicrobials in runoff. However, among the three application methods tested broadcast resulted in the highest total mass loading of antimicrobials in runoff from the three rainfall simulation tests. The aqueous concentrations of chlortetracyline and tylosin in runoff decreased in consecutive rainfall events, although the trend was only statistically significant for tylosin. For ARGs, broadcast resulted in significantly higher erm genes in runoff than did incorporation and injection methods. In soil, the effects of land application methods on the fate of antimicrobials in top soil were compound specific. No clear trend was observed in the ARG levels in soil, likely because different host cells may respond differently to the soil environments created by various land application methods.

  1. Growth potential of Clostridium perfringens from spores in acidified beef, pork, and poultry products during chilling.

    PubMed

    Juneja, Vijay K; Baker, David A; Thippareddi, H; Snyder, O Peter; Mohr, Tim B

    2013-01-01

    The ability of Clostridium perfringens to germinate and grow in acidified ground beef as well as in 10 commercially prepared acidified beef, pork, and poultry products was assessed. The pH of ground beef was adjusted with organic vinegar to achieve various pH values between 5.0 and 5.6; the pH of the commercial products ranged from 4.74 to 6.35. Products were inoculated with a three-strain cocktail of C. perfringens spores to achieve ca. 2-log (low) or 4-log (high) inoculum levels, vacuum packaged, and cooled exponentially from 54.4 to 7.2°C for 6, 9, 12, 15, 18, or 21 h to simulate abusive cooling; the U.S. Department of Agriculture, Food Safety and Inspection Service (USDA-FSIS) recommends a cooling time of 6.5 h. Total germinated C. perfringens populations were determined after plating on tryptose-sulfite-cycloserine agar and incubating the plates anaerobically at 37°C for 48 h. In addition, C. perfringens growth from spores was assessed at an isothermal temperature of 44°C. Growth from spores was inhibited in ground beef with a pH of 5.5 or below, even during extended cooling from 54.4 to 7.2°C in 21 h. In ground beef with a pH of 5.6, the growth was >1 log after 18 h of cooling from 54.4 to 7.2°C. However, 15 h of cooling controlled the growth to <1 log, regardless of the inoculum level. In addition, no growth was observed in any product with a pH ranging from 4.74 to 5.17, both during exponential abusive cooling periods of up to 21 h and during storage for 21 h at 44°C. While <1-log growth of C. perfringens from spores was observed in the pH 5.63 product cooled exponentially from 54.4 to 7.2°C in 15 h or less, the pH 6.35 product supported growth, even after 6 h of cooling from 54.4 to 7.2°C. These challenge tests demonstrate that adjustment of ground beef to pH of 5.5 or less and of barbeque products to pH of 5.63 or less inhibits C. perfringens spore germination and outgrowth during extended cooling periods from 54.4 to 7.2°C up to 15 h. Therefore

  2. Combined on-board hydride slurry storage and reactor system and process for hydrogen-powered vehicles and devices

    SciTech Connect

    Brooks, Kriston P; Holladay, Jamelyn D; Simmons, Kevin L; Herling, Darrell R

    2014-11-18

    An on-board hydride storage system and process are described. The system includes a slurry storage system that includes a slurry reactor and a variable concentration slurry. In one preferred configuration, the storage system stores a slurry containing a hydride storage material in a carrier fluid at a first concentration of hydride solids. The slurry reactor receives the slurry containing a second concentration of the hydride storage material and releases hydrogen as a fuel to hydrogen-power devices and vehicles.

  3. Strong Ion Regulatory Abilities Enable the Crab Xenograpsus testudinatus to Inhabit Highly Acidified Marine Vent Systems

    PubMed Central

    Hu, Marian Y.; Guh, Ying-Jey; Shao, Yi-Ta; Kuan, Pou-Long; Chen, Guan-Lin; Lee, Jay-Ron; Jeng, Ming-Shiou; Tseng, Yung-Che

    2016-01-01

    Hydrothermal vent organisms have evolved physiological adaptations to cope with extreme abiotic conditions including temperature and pH. To date, acid-base regulatory abilities of vent organisms are poorly investigated, although this physiological feature is essential for survival in low pH environments. We report the acid-base regulatory mechanisms of a hydrothermal vent crab, Xenograpsus testudinatus, endemic to highly acidic shallow-water vent habitats with average environment pH-values ranging between 5.4 and 6.6. Within a few hours, X. testudinatus restores extracellular pH (pHe) in response to environmental acidification of pH 6.5 (1.78 kPa pCO2) accompanied by an increase in blood HCO3- levels from 8.8 ± 0.3 to 31 ± 6 mM. Branchial Na+/K+-ATPase (NKA) and V-type H+-ATPase (VHA), the major ion pumps involved in branchial acid-base regulation, showed dynamic increases in response to acidified conditions on the mRNA, protein and activity level. Immunohistochemical analyses demonstrate the presence of NKA in basolateral membranes, whereas the VHA is predominantly localized in cytoplasmic vesicles of branchial epithelial- and pillar-cells. X. testudinatus is closely related to other strong osmo-regulating brachyurans, which is also reflected in the phylogeny of the NKA. Accordingly, our results suggest that the evolution of strong ion regulatory abilities in brachyuran crabs that allowed the occupation of ecological niches in euryhaline, freshwater, and terrestrial habitats are probably also linked to substantial acid-base regulatory abilities. This physiological trait allowed X. testudinatus to successfully inhabit one of the world's most acidic marine environments. PMID:26869933

  4. Multiphase reactivity of gaseous hydroperoxide oligomers produced from isoprene ozonolysis in the presence of acidified aerosols

    NASA Astrophysics Data System (ADS)

    Riva, Matthieu; Budisulistiorini, Sri Hapsari; Zhang, Zhenfa; Gold, Avram; Thornton, Joel A.; Turpin, Barbara J.; Surratt, Jason D.

    2017-03-01

    Ozonolysis of alkenes results in the formation of primary ozonides (POZs), which can subsequently decompose into carbonyl compounds and stabilized Criegee intermediates (sCIs). The sCIs generated from isoprene ozonolysis include the simplest congener, formaldehyde oxide (CH2OO), and isomers of C4-sCI. Although the bimolecular reaction with H2O is expected to be the main fate of sCIs, it was reported that sCIs can also react with carboxylic acids and/or organic hydroperoxides leading to gas-phase oligomeric compounds. While the impact of the gas-phase composition (H2O, sCI scavenger) on the formation of such products was recently studied, their fate remains unclear. In the present work, formation of oligomeric hydroperoxides from isoprene ozonolysis, proposed as reaction products composed of the sCI as a chain unit and formed from the insertion of sCI into a hydroperoxide or a carboxylic acid, was systematically examined in the presence of aerosol with varying compositions. The effect of hydroxyl (OH) radicals on the gas- and particle-phase compositions was investigated using diethyl ether as an OH radical scavenger. Thirty-four oligomeric compounds resulting from the insertion of sCIs into organic hydroperoxides or carboxylic acids were identified using iodide chemical ionization high-resolution mass spectrometry. Large reactive uptake onto acidified sulfate aerosol was observed for most of the characterized gaseous oligomeric species, whereas the presence of organic coatings and the lack of aerosol water significantly reduced or halted the reactive uptake of these species. These results indicate that highly oxidized molecules, such as hydroperoxides, could undergo multiphase reactions, which are significantly influenced by the chemical composition of seed aerosol. Furthermore, in addition to functionalization and accretion, decomposition and re-volatilization should be considered in SOA formation.

  5. Trends in emissions of acidifying species in Asia, 1985-1997.

    SciTech Connect

    Streets, D. G.; Tsai, N. Y.; Akimoto, H.; Oka, K.

    2000-05-31

    Acid deposition is a serious problem throughout much of Asia. Emissions of sulfur dioxide (SO{sub 2}) and nitrogen oxides (NO{sub x}) have been increasing steadily, as nations strive to increase their levels of economic development. Coal and fuel oil have been the main choices for powering industrial development; and, until recently, only a few countries (notably Japan and Taiwan) had taken significant steps to avert the atmospheric emissions that accompany fuel combustion. This paper discusses trends in emissions of SO{sub 2} and NO{sub x} that have occurred in Asian countries in the period 1985--1997, using results from the RAINS-ASIA computer model and energy-use trends from the IEA Energy Statistics and Balances database. Emissions of SO{sub 2} in Asia grew from 26.6 Tg in 1985 to 33.7 Tg in 1990 and to 39.2 Tg in 1997. Though SO{sub 2} emissions used to grow as fast as fossil-fuel use, recent limitations on the sulfur content of coal and oil have slowed the growth. The annual-average emissions growth between 1990 and 1997 was only 1.1%, considerably less than the economic growth rate. Emissions of NO{sub x}, on the other hand, continue to grow rapidly, from 14.1 Tg in 1985 to 18.7 Tg in 1990 and 28.5 Tg in 1997, with no signs of abating. Thus, though SO{sub 2} remains the major contributor to acidifying emissions in Asia, the role of NO{sub x}, will become more and more important in the future.

  6. Disrupting Hypoxia-Induced Bicarbonate Transport Acidifies Tumor Cells and Suppresses Tumor Growth.

    PubMed

    McIntyre, Alan; Hulikova, Alzbeta; Ledaki, Ioanna; Snell, Cameron; Singleton, Dean; Steers, Graham; Seden, Peter; Jones, Dylan; Bridges, Esther; Wigfield, Simon; Li, Ji-Liang; Russell, Angela; Swietach, Pawel; Harris, Adrian L

    2016-07-01

    Tumor hypoxia is associated clinically with therapeutic resistance and poor patient outcomes. One feature of tumor hypoxia is activated expression of carbonic anhydrase IX (CA9), a regulator of pH and tumor growth. In this study, we investigated the hypothesis that impeding the reuptake of bicarbonate produced extracellularly by CA9 could exacerbate the intracellular acidity produced by hypoxic conditions, perhaps compromising cell growth and viability as a result. In 8 of 10 cancer cell lines, we found that hypoxia induced the expression of at least one bicarbonate transporter. The most robust and frequent inductions were of the sodium-driven bicarbonate transporters SLC4A4 and SLC4A9, which rely upon both HIF1α and HIF2α activity for their expression. In cancer cell spheroids, SLC4A4 or SLC4A9 disruption by either genetic or pharmaceutical approaches acidified intracellular pH and reduced cell growth. Furthermore, treatment of spheroids with S0859, a small-molecule inhibitor of sodium-driven bicarbonate transporters, increased apoptosis in the cell lines tested. Finally, RNAi-mediated attenuation of SLC4A9 increased apoptosis in MDA-MB-231 breast cancer spheroids and dramatically reduced growth of MDA-MB-231 breast tumors or U87 gliomas in murine xenografts. Our findings suggest that disrupting pH homeostasis by blocking bicarbonate import might broadly relieve the common resistance of hypoxic tumors to anticancer therapy. Cancer Res; 76(13); 3744-55. ©2016 AACR.

  7. Experiments and modeling of variably permeable carbonate reservoir samples in contact with CO₂-acidified brines

    DOE PAGES

    Smith, Megan M.; Hao, Yue; Mason, Harris E.; ...

    2014-12-31

    Reactive experiments were performed to expose sample cores from the Arbuckle carbonate reservoir to CO₂-acidified brine under reservoir temperature and pressure conditions. The samples consisted of dolomite with varying quantities of calcite and silica/chert. The timescales of monitored pressure decline across each sample in response to CO₂ exposure, as well as the amount of and nature of dissolution features, varied widely among these three experiments. For all samples cores, the experimentally measured initial permeability was at least one order of magnitude or more lower than the values estimated from downhole methods. Nondestructive X-ray computed tomography (XRCT) imaging revealed dissolution featuresmore » including “wormholes,” removal of fracture-filling crystals, and widening of pre-existing pore spaces. In the injection zone sample, multiple fractures may have contributed to the high initial permeability of this core and restricted the distribution of CO₂-induced mineral dissolution. In contrast, the pre-existing porosity of the baffle zone sample was much lower and less connected, leading to a lower initial permeability and contributing to the development of a single dissolution channel. While calcite may make up only a small percentage of the overall sample composition, its location and the effects of its dissolution have an outsized effect on permeability responses to CO₂ exposure. The XRCT data presented here are informative for building the model domain for numerical simulations of these experiments but require calibration by higher resolution means to confidently evaluate different porosity-permeability relationships.« less

  8. Functionalized bio-artifact fabricated via selective slurry extrusion. Part 1: Preparation of slurry containing tourmaline superfine powders.

    PubMed

    Zhu, Dongbin; Xu, Anping; Qu, Yunxia; Liu, Yushan

    2011-12-01

    The far infrared dental porcelain slurry for fabricating artificial tooth via selective slurry extrusion (SSE) of solid freeform fabrication (also known as rapid prototyping) techniques was prepared by using tourmaline as additive and employing ball-milling approach. After characterization by transmission electron microscopy, X-ray diffraction, and Fourier transform infrared spectrometry, it was found that the far infrared emission properties of the dental porcelain were apparently improved in the ranges of 2000-1201 cm(-1) and 881-600 cm(-1). This is due to the increase of the number of infrared active bonds that are from the tourmaline superfine powders. Moreover, it was also found that the tourmaline superfine powders can improve the pseudo-plastic properties of dental porcelain slurries, which results from the increase of the absolute value of zeta potential of the suspensions. Slurries with pseudo-plastic behavior are highly desirable in controlling the shape of the extrudate during solid freeform fabrication. With the functionalized material, a variety of bio-artifacts beneficial to body health can be built by using selective slurry extrusion machine.

  9. Rheological behavior of molten Al-SiC slurries and comparison of their behavior with metallic slurries

    NASA Astrophysics Data System (ADS)

    Heidary, D. Sohrabi Baba; Akhlagh, F.

    2013-07-01

    In this study a new precise rotational viscometer was developed and used to measure the viscosity of molten A356 alloy containing 5, 15, and 25vol.% of 90-106 μm SiC particles at 650 and 690 °C. Three types of typical curves viscosity (η) versus volume fraction of SiC particles, shear time (t), and shear rate (γ) were derived advantage from the results of viscosity measurements. It would present the viscosity got lowered by decreasing particle volume fraction and by increasing the amounts of shear time and shear rate. In the next step, the influence of the number of aggregates on apparent viscosity was studied by the special tests, developed in this research. Also the formation of aggregates in Al-SiC composite slurries was explained and compared with metallic slurries. It concluded that the origin of aggregation in Al-SiC slurries was long range electrical forces while in metallic slurries it was micro welds between particles. it would show the rheological behavior of Al-SiC slurries could be justified according to the nature and the numbers of their aggregates. At the end, the implications of findings in order to predict the gradient of particles in functionally graded Al-SiC composites, produced by casting, were discussed.

  10. Slurry burner for mixture of carbonaceous material and water

    DOEpatents

    Nodd, D.G.; Walker, R.J.

    1985-11-05

    The present invention is intended to overcome the limitations of the prior art by providing a fuel burner particularly adapted for the combustion of carbonaceous material-water slurries which includes a stationary high pressure tip-emulsion atomizer which directs a uniform fuel into a shearing air flow as the carbonaceous material-water slurry is directed into a combustion chamber, inhibits the collection of unburned fuel upon and within the atomizer, reduces the slurry to a collection of fine particles upon discharge into the combustion chamber, and regulates the operating temperature of the burner as well as primary air flow about the burner and into the combustion chamber for improved combustion efficiency, no atomizer plugging and enhanced flame stability.

  11. Mud management, special slurries improve deepwater cementing operations

    SciTech Connect

    Griffith, J.; Faul, R.

    1997-10-20

    Successful deepwater cementing requires improved mud-management techniques to reduce fluid loss, shorten slurry transition times, and make mud and cement slurry weights compatible with formation pore pressure and fracture gradients. If any one of these conditions is not met, the cementing job is less likely to be successful. Previous attempts to drill in deep water have had a low success rate, and failures have cost operators an average $2 million/well. By using new mud-management techniques and specially designed cement mixtures, operators in the Gulf of Mexico (GOM) are effectively setting conductor casing in deepwater conditions and are greatly improving the success rate in cementing deepwater wells. Recent case histories in the GOM describe these new techniques and the advantages of using a specially formulated, lightweight, foamed cement slurry to avoid cement-sheath damage caused by shallow-water flow.

  12. Microalgal cultivation with biogas slurry for biofuel production.

    PubMed

    Zhu, Liandong; Yan, Cheng; Li, Zhaohua

    2016-11-01

    Microalgal growth requires a substantial amount of chemical fertilizers. An alternative to the utilization of fertilizer is to apply biogas slurry produced through anaerobic digestion to cultivate microalgae for the production of biofuels. Plenty of studies have suggested that anaerobic digestate containing high nutrient contents is a potentially feasible nutrient source to culture microalgae. However, current literature indicates a lack of review available regarding microalgal cultivation with biogas slurry for the production of biofuels. To help fill this gap, this review highlights the integration of digestate nutrient management with microalgal production. It first unveils the current status of microalgal production, providing basic background to the topic. Subsequently, microalgal cultivation technologies using biogas slurry are discussed in detail. A scale-up scheme for simultaneous biogas upgrade and digestate application through microalgal cultivation is then proposed. Afterwards, several uncertainties that might affect this practice are explored. Finally, concluding remarks are put forward.

  13. Tape casting of cobalt ferrite from nonaqueous slurry

    NASA Astrophysics Data System (ADS)

    Jian, Gang; Zhou, Dongxiang; Yang, Junyou; Fu, Qiuyun

    2012-12-01

    This paper describes the fabrication of CoFe2O4 thick films using the tape casting method from nonaqueous slurry. CoFe2O4 particles with average size of ˜800 nm were prepared by the solid-state reaction method. Sediment volumes and viscosity were tested to study the effects of dispersant in reducing aggregations in slurry. Slurry with 0.25 wt% dispersant amounts and 41.3 wt% solid content showed the optimal stability and rheological properties. A tape velocity of 8 cm/s was used in this study considering the non-Newtonian flow behavior at low shear rate. CoFe2O4 ceramic films sintered at 1150 °C for 2 h have dense structure (relative density of 94%) and exhibited ferromagnetic properties with in-plane saturation magnetization of ˜324 emu/cm3.

  14. Method and apparatus for in-situ drying investigation and optimization of slurry drying methodology

    DOEpatents

    Armstrong, Beth L.; Daniel, Claus; Howe, Jane Y.; Kiggans, Jr, James O.; Sabau, Adrian S.; Wood, III, David L.; Kalnaus, Sergiy

    2016-05-10

    A method of drying casted slurries that includes calculating drying conditions from an experimental model for a cast slurry and forming a cast film. An infrared heating probe is positioned on one side of the casted slurry and a thermal probe is positioned on an opposing side of the casted slurry. The infrared heating probe may control the temperature of the casted slurry during drying. The casted slurry may be observed with an optical microscope, while applying the drying conditions from the experimental model. Observing the casted slurry includes detecting the incidence of micro-structural changes in the casted slurry during drying to determine if the drying conditions from the experimental model are optimal.

  15. Development of Alternative Rheological Measurements for DWPF Slurry Samples (U)

    SciTech Connect

    Koopman, D. c.

    2005-09-01

    Rheological measurements are used to evaluate the fluid dynamic behavior of Defense Waste Processing Facility, DWPF, slurry samples. Measurements are currently made on non-radioactive simulant slurries using two state-of-the-art rheometers located at the Aiken County Technical Laboratory, ACTL. Measurements are made on plant samples using a rheometer in the Savannah River National Laboratory, SRNL, Shielded Cells facility. Low activity simulants or plant samples can be analyzed using a rheometer located in a radioactive hood in SRNL. Variations in the rheology of SB2 simulants impacted the interpretation of results obtained in a number of related studies. A separate rheological study was initiated with the following four goals: (1) Document the variations seen in the simulant slurries, both by a review of recent data, and by a search for similar samples for further study. (2) Attempt to explain the variations in rheological behavior, or, failing that, reduce the number of possible causes. In particular, to empirically check for rheometer-related variations. (3) Exploit the additional capabilities of the rheometers by developing new measurement methods to study the simulant rheological properties in new ways. (4) Formalize the rheological measurement process for DWPF-related samples into a series of protocols. This report focuses on the third and fourth goals. The emphasis of this report is on the development and formalization of rheological measurement methods used to characterize DWPF slurry samples. The organization is by rheological measurement method. Progress on the first two goals was documented in a concurrent technical report, Koopman (2005). That report focused on the types and possible causes of unusual rheological behavior in simulant slurry samples. It was organized by the sample being studied. The experimental portion of this study was performed in the period of March to April 2004. A general rheology protocol for routine DWPF slurry samples, Koopman

  16. Steam Explosions in Slurry-fed Ceramic Melters

    SciTech Connect

    Carter, J.T.

    2001-03-28

    This report assesses the potential and consequences of a steam explosion in Slurry Feed Ceramic Melters (SFCM). The principles that determine if an interaction is realistically probable within a SFCM are established. Also considered are the mitigating effects due to dissolved, non-condensable gas(es) and suspended solids within the slurry feed, radiation, high glass viscosity, and the existence of a cold cap. The report finds that, even if any explosion were to occur, however, it would not be large enough to compromise vessel integrity.

  17. Urolithiasis in finishing pigs.

    PubMed

    Maes, D G D; Vrielinck, J; Millet, S; Janssens, G P J; Deprez, P

    2004-11-01

    Urolithiasis in sows and neonatal pigs is well-known, but information on its occurrence and impact in finishing pigs is sparse. This study reports three outbreaks of urolithiasis in finishing pigs. In one herd, no symptoms were observed, whereas in the other herds the presence of calculi caused obstruction of the urinary tract resulting in death. Using infra-red spectroscopy, the predominant mineral-type found in the uroliths was calcium carbonate (calcite). Only small amounts of calcium oxalate (< 1%) could be detected. A high urinary pH, small abnormalities in the mineral composition of the feed and insufficient drinking water were the most important risk factors identified. To prevent urolithiasis, it is important to ensure adequate water intake, to provide a balanced mineral diet, and to avoid urinary tract infections.

  18. SYNTHESIS OF NON-RADIOACTIVE SLURRIES TO SIMULATE THE PROCESSING BEHAVIOR OF PARTICLES IN RADIOACTIVE WASTE SLURRIES 626-G

    SciTech Connect

    Koopman, D.; Lambert, D.; Eibling, R.; Newell, J.; Stone, M.

    2009-09-03

    Process development using non-radioactive analogs to high-level radioactive waste slurries is an established cost effective alternative to working with actual samples of the real waste. Current simulated waste slurries, however, do not capture all of the physical behavior of real waste. New methods of preparing simulants are under investigation along with mechanisms for altering certain properties of finished simulants. These methods have achieved several notable successes recently in the areas of rheology and foaminess. Particle size is also being manipulated more effectively than in the past, though not independently of the rheological properties. The interaction between rheology and foaminess has exhibited counter-intuitive behavior with more viscous slurries being less foamy even though drainage of liquid from the foam lamellae should be inhibited by higher viscosities.

  19. Slurry pumping techniques for feeding high-pressure coal gasification reactors

    NASA Technical Reports Server (NTRS)

    Bair, W. G.; Tarman, P. B.

    1977-01-01

    Operating experience in pumping coal and coal char slurries at pressures up to 1500 psig is discussed. The design specifications for the mixing tanks, pumps, piping, and slurry heaters are given along with pressure drop and minimum flow velocity data on water-lignite slurries.

  20. Effects of dairy slurry on the nutritive value and fermentation characteristics of alfalfa silages

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Dairy producers frequently ask questions about the risks associated with applying dairy slurry onto growing alfalfa. Our objectives were to determine the effects of dairy-slurry application on the subsequent nutritive value and fermentation characteristics of alfalfa silages. Dairy slurry was applie...

  1. 30 CFR 77.216 - Water, sediment, or slurry impoundments and impounding structures; general.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Water, sediment, or slurry impoundments and... WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216 Water, sediment, or slurry... structures which impound water, sediment, or slurry shall be required if such an existing or...

  2. 30 CFR 77.216 - Water, sediment, or slurry impoundments and impounding structures; general.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Water, sediment, or slurry impoundments and... WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216 Water, sediment, or slurry... structures which impound water, sediment, or slurry shall be required if such an existing or...

  3. 30 CFR 77.216 - Water, sediment, or slurry impoundments and impounding structures; general.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Water, sediment, or slurry impoundments and... WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216 Water, sediment, or slurry... structures which impound water, sediment, or slurry shall be required if such an existing or...

  4. 30 CFR 77.216 - Water, sediment, or slurry impoundments and impounding structures; general.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Water, sediment, or slurry impoundments and... WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216 Water, sediment, or slurry... structures which impound water, sediment, or slurry shall be required if such an existing or...

  5. 30 CFR 77.216 - Water, sediment, or slurry impoundments and impounding structures; general.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Water, sediment, or slurry impoundments and... WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216 Water, sediment, or slurry... structures which impound water, sediment, or slurry shall be required if such an existing or...

  6. DWPF DECON FRIT: SUMP AND SLURRY SOLIDS ANALYSIS

    SciTech Connect

    Crawford, C.; Peeler, D.; Click, D.

    2010-10-20

    The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. In this report, the physical and chemical characterization results of the slurry solids and sump solids are reported. Crawford et al. (2010) provide the results of the supernate analysis. The results of the sump solids are reported on a mass basis given the samples were essentially dry upon receipt. The results of the slurry solids were converted to a volume basis given approximately 2.4 grams of slurry solids were obtained from the {approx}4 liters of liquid slurry sample. Although there were slight differences in the analytical results between the sump solids and slurry solids the following general summary statements can be made. Slight differences in the results are also captured for specific analysis. (1) Physical characterization - (a) SEM/EDS analysis suggested that the samples were enriched in Li and Si (B and Na not detectable using the current EDS system) which is consistent with two of the four principle oxides of Frit 418 (B{sub 2}O{sub 3}, Na{sub 2}O, Li{sub 2}O and SiO{sub 2}). (b) SEM/EDS analysis also identified impurities which were elementally consistent with stainless steel (i.e., Fe, Ni, Cr contamination). (c) XRD results indicated that the sump solids samples were amorphous which is consistent with XRD results expected for a Frit 418 based sample. (d) For the sump solids, SEM/EDS analysis indicated that the particle size of the sump solids were consistent with that of an as received Frit 418 sample from a current DWPF vendor. (e) For the slurry solids, SEM/EDS analysis indicated that the particle size range

  7. The most acidified Austrian lake in comparison to a neutralized mining lake

    PubMed Central

    Moser, Michael; Weisse, Thomas

    2011-01-01

    This study investigated two mining lakes located in the north of Lower Austria. These lakes arose 45 years ago when open cast lignite mining ceased. The lakes are separated by a 7-m wide dam. Due to the oxidation of pyrite, both lakes have been acidified and exhibit iron, sulphate, and heavy metal concentrations several orders of magnitude higher than in circumneutral lakes. The water column of both lakes is divided into two layers by a pronounced chemocline. The smaller mining lake (AML), with pH close to of 2.6, is the most acidic lake in Austria, whereas flooding with stream water and by drainage from the surrounding fields neutralized the adjacent larger pit lake. The goal of our study was to investigate the effect of flooding on its physical, chemical and biological properties, in comparison to the pristine AML. Even relative to other extremely acidic lakes, the flora and fauna in the AML was reduced and composed of only two flagellate, one ciliate, and one rotifer species. The simplified pelagic food web in the mixolimnion consisted of heterotrophic bacteria, the mixotrophic flagellates Chlamydomonas acidophila and Ochromonas sp., the ciliate Oxytricha sp., and the rotifer Cephalodella sp. The latter two are as yet undescribed new species. The heliozoan Actinophrys sp. that may act as top predator occurred only in low abundance. The euglenid Lepocinclis buetschlii formed a stable deep chlorophyll maximum (DCM) at 7 m depth. Highest cell numbers of L. buetschlii in the DCM exceeded 108 L−1. The neutralized mining lake harboured higher plankton diversity similar to that of natural circumneutral lakes. A peak of at least 16 different phytoplankton taxa was observed during summer. The zooplankton consisted of several copepod species, daphnids and other cladocerans, and at least six different rotifer species. Several fish species occurred in the neutralized lake. Although the effect of non-permanent flooding was largely sustainable, interannual fluctuations of

  8. The most acidified Austrian lake in comparison to a neutralized mining lake.

    PubMed

    Moser, Michael; Weisse, Thomas

    2011-12-01

    This study investigated two mining lakes located in the north of Lower Austria. These lakes arose 45 years ago when open cast lignite mining ceased. The lakes are separated by a 7-m wide dam. Due to the oxidation of pyrite, both lakes have been acidified and exhibit iron, sulphate, and heavy metal concentrations several orders of magnitude higher than in circumneutral lakes. The water column of both lakes is divided into two layers by a pronounced chemocline. The smaller mining lake (AML), with pH close to of 2.6, is the most acidic lake in Austria, whereas flooding with stream water and by drainage from the surrounding fields neutralized the adjacent larger pit lake. The goal of our study was to investigate the effect of flooding on its physical, chemical and biological properties, in comparison to the pristine AML. Even relative to other extremely acidic lakes, the flora and fauna in the AML was reduced and composed of only two flagellate, one ciliate, and one rotifer species. The simplified pelagic food web in the mixolimnion consisted of heterotrophic bacteria, the mixotrophic flagellates Chlamydomonas acidophila and Ochromonas sp., the ciliate Oxytricha sp., and the rotifer Cephalodella sp. The latter two are as yet undescribed new species. The heliozoan Actinophrys sp. that may act as top predator occurred only in low abundance. The euglenid Lepocinclis buetschlii formed a stable deep chlorophyll maximum (DCM) at 7 m depth. Highest cell numbers of L. buetschlii in the DCM exceeded 10(8) L(-1). The neutralized mining lake harboured higher plankton diversity similar to that of natural circumneutral lakes. A peak of at least 16 different phytoplankton taxa was observed during summer. The zooplankton consisted of several copepod species, daphnids and other cladocerans, and at least six different rotifer species. Several fish species occurred in the neutralized lake. Although the effect of non-permanent flooding was largely sustainable, interannual fluctuations

  9. Modifications of Carbonate Fracture Hydrodynamic Properties by CO 2 -Acidified Brine Flow

    SciTech Connect

    Deng, Hang; Ellis, Brian R.; Peters, Catherine A.; Fitts, Jeffrey P.; Crandall, Dustin; Bromhal, Grant S.

    2013-08-15

    Acidic reactive flow in fractures is relevant in subsurface activities such as CO{sub 2} geological storage and hydraulic fracturing. Understanding reaction-induced changes in fracture hydrodynamic properties is essential for predicting subsurface flows such as leakage, injectability, and fluid production. In this study, x-ray computed tomography scans of a fractured carbonate caprock were used to create three dimensional reconstructions of the fracture before and after reaction with CO{sub 2}-acidified brine (Ellis et al., 2011, Greenhouse Gases: Sci. Technol., 1:248-260). As expected, mechanical apertures were found to increase substantially, doubling and even tripling in some places. However, the surface geometry evolved in complex ways including ‘comb-tooth’ structures created from preferential dissolution of calcite in transverse sedimentary bands, and the creation of degraded zones, i.e. porous calcite-depleted areas on reacted fracture surfaces. These geometric alterations resulted in increased fracture roughness, as measured by surface Z{sub 2} parameters and fractal dimensions D{sub f}. Computational fluid dynamics (CFD) simulations were conducted to quantify the changes in hydraulic aperture, fracture transmissivity and permeability. The results show that the effective hydraulic apertures are smaller than the mechanical apertures, and the changes in hydraulic apertures are nonlinear. Overestimation of flow rate by a factor of two or more would be introduced if fracture hydrodynamic properties were based on mechanical apertures, or if hydraulic aperture is assumed to change proportionally with mechanical aperture. The differences can be attributed, in part, to the increase in roughness after reaction, and is likely affected by contiguous transverse sedimentary features. Hydraulic apertures estimated by the 1D statistical model and 2D local cubic law (LCL) model are consistently larger than those calculated from the CFD simulations. In addition, a novel

  10. Can the eastern red-backed salamander (Plethodon cinereus) persist in an acidified landscape?

    USGS Publications Warehouse

    Bondi, Cheryl A; Beier, Colin M.; Ducey, Peter K; Lawrence, Gregory B.; Bailey, Scott W.

    2016-01-01

    Hardwood forests of eastern North America have experienced decades of acidic deposition, leading to soil acidification where base cation supply was insufficient to neutralize acid inputs. Negative impacts of soil acidity on amphibians include disrupted embryonic development, lower growth rates, and habitat loss. However, some amphibians exhibit intraspecific variation in acid tolerance, suggesting the potential for local adaptation in areas where soils are naturally acidic. The eastern red-backed salamander (Plethodon cinereus) is a highly abundant top predator of the northern hardwood forest floor. Early research found that P. cinereus was sensitive to acidic soils, avoiding substrates with pH < 3.8 and experiencing decreased growth rates in acidic habitats. However, recent studies have documented P. cinereus populations in lower pH conditions than previously observed, suggesting some populations may persist in acidic conditions. Here, we evaluated relationships between organic horizon soil pH and P. cinereus abundance, adult health (body size and condition), and microhabitat selection, based on surveys of 34 hardwood forests in northeastern United States that encompass a regional soil pH gradient. We found no associations between soil pH and P. cinereus abundance or health, and observed that this salamander used substrates with pH similar to that available, suggesting that pH does not mediate their fine-scale distributions. The strongest negative predictor of P. cinereus abundance was the presence of dusky salamanders (Desmognathus spp.), which were most abundant in the western Adirondacks. Our results indicate that P. cinereus occupies a wider range of soil pH than has been previously thought, which has implications for their functional role in forest food webs and nutrient cycles in acid-impaired ecosystems. Tolerance of P. cinereus for more acidic habitats, including anthropogenically acidified forests, may be due to local adaptation in

  11. Method for freeforming objects with low-binder slurry

    DOEpatents

    Cesarano, III, Joseph; Calvert, Paul D.

    2002-01-01

    In a rapid prototyping system, a part is formed by depositing a bead of slurry that has a sufficient high concentration of particles to be pseudoplastic and almost no organic binders. After deposition the bead is heated to drive off sufficient liquid to cause the bead to become dilatant.

  12. Breakup of evaporating/burning slurry drops by additives

    NASA Astrophysics Data System (ADS)

    Choudhury, P. Roy; Gerstein, M.

    Single drops of silicon carbide-cumene slurry were suspended from a quartz fiber and ignited. An inert material such as silicon carbide was chosen so that the droplets can be burned until all the fuel is consumed and only the inert residue is left on the quartz fiber. Benzoyl peroxide was added to cumene and the time to disruption of the liquid drop was measured. In the case of benzoyl peroxide, the breaking up of the drop resulting from its thermal decomposition produced CO 2. Both the drop disruption time and the burning of the slurry to dryness were predicted theoretically. Radiation absorption was found to be an important factor in the case of the slurry. Benzoyl peroxide and carbamide peroxide were investigated as additives to a boron slurry to determine if effective drop break-up could be achieved. Both additives produced drop shattering. The carbamide peroxide was particularly effective due to the production of O 2. The green flame associated with boron burning was clearly evident.

  13. Apparatus for converting biomass to a pumpable slurry

    DOEpatents

    Ergun, Sabri; Schaleger, Larry L.; Wrathall, James A.; Yaghoubzadeh, Nasser

    1986-01-01

    An apparatus used in the pretreatment of wood chips in a process for converting biomass to a liquid hydrocarbonaceous fuel. The apparatus functions to break down the wood chips to a size distribution that can be readily handled in a slurry form. Low maintenance operation is obtained by hydrolyzing the chips in a pressure vessel having no moving parts.

  14. NOVEL SLURRY PHASE DIESEL CATALYSTS FOR COAL-DERIVED SYNGAS

    SciTech Connect

    Dr. Dragomir B. Bukur; Dr. Ketil Hanssen; Alec Klinghoffer; Dr. Lech Nowicki; Patricia O'Dowd; Dr. Hien Pham; Jian Xu

    2001-01-07

    This report describes research conducted to support the DOE program in novel slurry phase catalysts for converting coal-derived synthesis gas to diesel fuels. The primary objective of this research program is to develop attrition resistant catalysts that exhibit high activities for conversion of coal-derived syngas.

  15. METHOD OF MAKING UO$sub 2$-Bi SLURRIES

    DOEpatents

    Hahn, H.T.

    1960-05-24

    A process is given of preparing an easily dispersible slurry of uranium dioxide in bismuth. A mixture of bismuth oxide, uranium, and bismuth are heated in a capsule to a temperature over the melting point of bismuth oxide. The amount of bismuth oxide used is less than that stoichiometrically required because the oxygen in the capsule also enters into the reaction.

  16. Design of slurry reactor for indirect liquefaction applications

    SciTech Connect

    Prakash, A.; Bendale, P.G.

    1991-01-01

    The objective of this project is to design and model a conceptual slurry reactor for two indirect liquefaction applications; (1) production of methanol and (2) production of hydrocarbon fuels via Fischer-Tropsch route. A slurry reactor is defined here as a three-phase bubble column reactor using a fine catalyst particle suspension in a high molecular weight liquid. The feed gas is introduced through spargers. It then bubbles through the column providing the agitation necessary for catalyst suspension and mass transfer. The reactor models for the two processes have been formulated using computer simulation. Process data, kinetic and thermodynamic data, heat and mass transfer data and hydrodynamic data have been used in the mathematical models to describe the slurry reactor for each of the two processes. Available data from process development units and demonstration units were used to test and validate the models. Commercial size slurry reactors for methanol and Fischer-Tropsch synthesis were sized using reactor models developed in this report.

  17. Design of slurry reactor for indirect liquefaction applications. Final report

    SciTech Connect

    Prakash, A.; Bendale, P.G.

    1991-12-31

    The objective of this project is to design and model a conceptual slurry reactor for two indirect liquefaction applications; (1) production of methanol and (2) production of hydrocarbon fuels via Fischer-Tropsch route. A slurry reactor is defined here as a three-phase bubble column reactor using a fine catalyst particle suspension in a high molecular weight liquid. The feed gas is introduced through spargers. It then bubbles through the column providing the agitation necessary for catalyst suspension and mass transfer. The reactor models for the two processes have been formulated using computer simulation. Process data, kinetic and thermodynamic data, heat and mass transfer data and hydrodynamic data have been used in the mathematical models to describe the slurry reactor for each of the two processes. Available data from process development units and demonstration units were used to test and validate the models. Commercial size slurry reactors for methanol and Fischer-Tropsch synthesis were sized using reactor models developed in this report.

  18. Particle sedimentation monitoring in high-concentration slurries

    NASA Astrophysics Data System (ADS)

    Nagasawa, Yoshihiro; Kato, Zenji; Tanaka, Satoshi

    2016-11-01

    In this study, the sedimentation states of particles in high-concentration slurries were elucidated by monitoring their internal states. We prepared transparent high-concentration silica slurries by adjusting the refractive index of the aqueous glycerol liquid in which the particles were dispersed to match that of the silica particles. In addition, a fluorescent dye was dissolved in the liquid. Then, we directly observed the individual and flocculated particles in the slurries during sedimentation by confocal laser scanning fluorescent microscopy. The particles were found to sediment very slowly while exhibiting fluctuating motion. The particle sedimentation rate in the high-concentration slurry with the aqueous glycerol solution (η =0.068 Pa. s ) and a particle volume fraction on the order of 0.3 was determined to be 1.58 ± 0.66 μ m. min-1 on the basis of the obtained image sequences for 24.9 h. In-situ observation provides a large amount of information about the sedimentation behavior of particles in condensed matter.

  19. St. Paul's Pig Pack.

    ERIC Educational Resources Information Center

    Miller, Penny Folley

    1982-01-01

    Describes a guinea pig (cavy) breeding and management program developed as part of an elementary school science curriculum. Includes comments on show competitions (sponsored by the American Rabbit Breeders Association) to measure the success of the breeding program and to enable children to experience the business world. (Author/JN)

  20. A Simple "Pig" Game

    ERIC Educational Resources Information Center

    Johnson, Roger W.

    2008-01-01

    Our pig game involves a series of tosses of a die with the possibility of a player's score improving with each additional toss. With each additional toss, however, there is also the chance of losing the entire score accumulated so far. Two different strategies for deciding how many tosses a player should attempt are developed and then compared in…

  1. Rheological Characterization of Unusual DWPF Slurry Samples (U)

    SciTech Connect

    Koopman, D. C.

    2005-09-01

    A study was undertaken to identify and clarify examples of unusual rheological behavior in Defense Waste Processing Facility (DWPF) simulant slurry samples. Identification was accomplished by reviewing sludge, Sludge Receipt and Adjustment Tank (SRAT) product, and Slurry Mix Evaporator (SME) product simulant rheological results from the prior year. Clarification of unusual rheological behavior was achieved by developing and implementing new measurement techniques. Development of these new methods is covered in a separate report, WSRC-TR-2004-00334. This report includes a review of recent literature on unusual rheological behavior, followed by a summary of the rheological measurement results obtained on a set of unusual simulant samples. Shifts in rheological behavior of slurries as the wt. % total solids changed have been observed in numerous systems. The main finding of the experimental work was that the various unusual DWPF simulant slurry samples exhibit some degree of time dependent behavior. When a given shear rate is applied to a sample, the apparent viscosity of the slurry changes with time rather than remaining constant. These unusual simulant samples are more rheologically complex than Newtonian liquids or more simple slurries, neither of which shows significant time dependence. The study concludes that the unusual rheological behavior that has been observed is being caused by time dependent rheological properties in the slurries being measured. Most of the changes are due to the effect of time under shear, but SB3 SME products were also changing properties while stored in sample bottles. The most likely source of this shear-related time dependence for sludge is in the simulant preparation. More than a single source of time dependence was inferred for the simulant SME product slurries based on the range of phenomena observed. Rheological property changes were observed on the time-scale of a single measurement (minutes) as well as on a time scale of hours

  2. Hanford Waste Vitrification Plant full-scale feed preparation testing with water and process simulant slurries

    SciTech Connect

    Gaskill, J.R.; Larson, D.E.; Abrigo, G.P.

    1996-03-01

    The Hanford Waste Vitrification Plant was intended to convert selected, pretreated defense high-level waste and transuranic waste from the Hanford Site into a borosilicate glass. A full-scale testing program was conducted with nonradioactive waste simulants to develop information for process and equipment design of the feed-preparation system. The equipment systems tested included the Slurry Receipt and Adjustment Tank, Slurry Mix Evaporator, and Melter-Feed Tank. The areas of data generation included heat transfer (boiling, heating, and cooling), slurry mixing, slurry pumping and transport, slurry sampling, and process chemistry. 13 refs., 129 figs., 68 tabs.

  3. Indian Creek-AML: Coal slurry reclamation (Kansas case history)

    SciTech Connect

    Witthar, S.R.

    1998-12-31

    Black and Veatch, assisted by Jack Nawrot, developed conceptual and final designs and provided construction assistance to create grasslands and wetlands in order to reclaim an abandoned coal mine for the state of Kansas. The mine included spoils, a coal refuse dump, and slurry pond in the Indian Creek drainage basin in east central Kansas. The Indian Creek flowed from an off-site abandoned mine and through the coal slurry pond where its waters became more polluted. The intent of the reclamation project was to improve water quality and create a wildlife refuge. The coal refuse was covered and seeded with a diversity of vegetation including several grasses and legume. The slurry pond was developed into a series of large wetland cells to improve water quality. Prior to reclamation, the water leaving the site had a typical pH of 3.3, ranging from 2.4 to 5.6, an iron content which typically over 22 mg/L and ranging over 100 mg/L, and contained large amounts of coal slurry. The acid sediment in the slurry killed fish and caused visible damage to a new large concrete box culvert several miles downstream of the site. Post-reclamation water quality leaving the Indian Creek site showed immediate improvement even before vegetation was reestablished. The existing wetland treatment systems have been successfully treating water for over seven years with the pH of the water leaving the wetlands above 7 and soluble iron content less than 1 mg/L. Fish in the constructed wetlands support waterfowl which now nest onsite.

  4. Evaluation of abiotic fate mechanisms in soil slurry bioreactor treatment

    SciTech Connect

    Glaser, J.A.; McCauley, P.T.; Dosani, M.A.

    1995-10-01

    Biological treatment of contaminated soil slurries may offer a viable technology for soil bioremediation. Slurry bioreactor treatment of soils, however, has not sufficiently progressed to be a durable, reliable, and cost-effective treatment option. Critical to the evaluation of slurry bioreactors is a better description of pollutant mass transfer during the treatment phase. Losses attributable to abiotic means are generally overlooked in field application of the technology. Discussions with EPA regional personnel and inspection of active soil slurry bioreactor operations have identified operational problems such as foaming which could result in possible abiotic loss. Field bioslurry operations have adopted various approaches to reduce foaming: (1) the addition of defoaming agents, (2) the reduction of rotational speed of the agitator, and (3) the reduction of gas flow through the bioreactor system. We have conducted two bench-scale slurry bioreactor treatability studies, at the U.S. EPA Testing & Evaluation Facility in Cincinnati, Ohio, which were designed to investigate some of the operating factors leading to foam formation and identify the most advantageous means to deal with foaming. The initial study has been previously presented as a general treatability study for treatment of creosote contamination in a soil. During this study, foaming became a major problem for operation. The foaming conditions were mitigated by use of defoamer and, in the more extreme cases, through reduction of the mixer rotational speed and gas flow. A subsequent study which was devoted specifically to investigating the causes and conditions of foaming using a different batch of soil from the same site as the earlier study showed little foaming at the very beginning of the study.

  5. The heterogeneous kinetics of HOBr and HOCl on acidified sea salt and model aerosol at 40-90% relative humidity and ambient temperature.

    PubMed

    Pratte, Pascal; Rossi, Michel J

    2006-09-14

    The HOBr and HOCl uptake coefficient gamma on H(2)SO(4)-acidified submicron salt aerosol of known size distribution was measured in an atmospheric pressure laminar flow reactor. The interaction time of the trace gas with the aerosol was in the range 15 to 90 s and led to gamma values in the range 10(-4) to 10(-2). The acidity of the aerosol is essential in order to enable heterogeneous reactions of HOBr on NaCl, recrystallized sea salt (RSS) and natural sea salt (NSS) aerosols. Specifically, HOCl only reacts on acidified NSS aerosol with a gamma ranging from 0.4 x 10(-3) to 1.8 x 10(-3) at a relative humidity (rh) at 40 and 85%, respectively. Uptake experiments of HOBr on aqueous H(2)SO(4) as well as on H(2)SO(4)-acidified NaCl, RSS or NSS aerosol were performed for rh ranging from 40 to 93%. The gamma value of HOBr on acidified NSS reaches a maximum gamma = 1.9 x 10(-2) at rh = 76 +/- 1% and significantly decreases with increasing rh in contrast to acidified NaCl and RSS aerosols whose gamma values remain high at gamma = (1.0 +/- 0.2) x 10(-2) at rh >/= 80%. An explanation based on the formation of an organic coating on NSS aerosol with increasing rh is proposed.

  6. Transport of Cryptosporidium parvum oocysts in soil columns following applications of raw and separated liquid slurries.

    PubMed

    Petersen, Heidi H; Enemark, Heidi L; Olsen, Annette; Amin, M G Mostofa; Dalsgaard, Anders

    2012-09-01

    The potential for the transport of viable Cryptosporidium parvum oocysts through soil to land drains and groundwater was studied using simulated rainfall and intact soil columns which were applied raw slurry or separated liquid slurry. Following irrigation and weekly samplings over a 4-week period, C. parvum oocysts were detected from all soil columns regardless of slurry type and application method, although recovery rates were low (<1%). Soil columns with injected liquid slurry leached 73 and 90% more oocysts compared to columns with injected and surface-applied raw slurries, respectively. Among leachate samples containing oocysts, 44/72 samples yielded viable oocysts as determined by a dye permeability assay (DAPI [4',6'-diamidino-2-phenylindole]/propidium iodide) with the majority (41%) of viable oocysts found in leachate from soil columns with added liquid slurry. The number of viable oocysts was positively correlated (r = 0.63) with the total number of oocysts found. Destructively sampling of the soil columns showed that type of slurry and irrigation played a role in the vertical distribution of oocysts, with more oocysts recovered from soil columns added liquid slurry irrespective of the irrigation status. Further studies are needed to determine the effectiveness of different slurry separation technologies to remove oocysts and other pathogens, as well as whether the application of separated liquid slurry to agricultural land may represent higher risks for groundwater contamination compared to application of raw slurry.

  7. Composition for a lightweight cement slurry for cementing oil and gas wells

    SciTech Connect

    Parcevaux, P.; Sault, P.

    1988-01-26

    A homogeneous lightweight cement slurry for cementing the annulus of an oil or gas well is described comprising: cement, an extender in the form of solid particles, a styrenebutadiene latex, and water, having a specific gravity lying substantially in the range from 1.2 to 1.6 and having a volume ratio of the liquid phase of the slurry to the total volume of the slurry of less than about 70%. A method of cementing the annulus of a wellbore by pumping an aqueous cement slurry through the wellbore and into the annulus the aqueous cement slurry comprising is described comprising cement, an extender in the form of solid particles, a styrenebutadiene latex and water, having a specific gravity lying substantially in the range from 1.2 to 1.6 and having a volume ratio of the liquid phase of the slurry to the total volume of the slurry of less than about 70%.

  8. Slurry atomizer for a coal-feeder and dryer used to provide coal at gasifier pressure

    DOEpatents

    Loth, John L.; Smith, William C.; Friggens, Gary R.

    1982-01-01

    The present invention is directed to a coal-water slurry atomizer for use a high-pressure dryer employed in a pumping system utilized to feed coal into a pressurized coal gasifier. The slurry atomizer is provided with a venturi, constant area slurry injection conduit, and a plurality of tangentially disposed steam injection ports. Superheated steam is injected into the atomizer through these ports to provide a vortical flow of the steam, which, in turn, shears slurry emerging from the slurry injection conduit. The droplets of slurry are rapidly dispersed in the dryer through the venturi where the water is vaporized from the slurry by the steam prior to deleterious heating of the coal.

  9. Detection of hepatitis E virus (HEV) through the different stages of pig manure composting plants

    PubMed Central

    García, M; Fernández-Barredo, S; Pérez-Gracia, M T

    2014-01-01

    Hepatitis E virus (HEV) is an increasing cause of acute hepatitis in industrialized countries. The aim of this study was to evaluate the presence of HEV in pig manure composting plants located in Spain. For this purpose, a total of 594 samples were taken in 54 sampling sessions from the different stages of composting treatment in these plants as follows: slurry reception ponds, anaerobic ponds, aerobic ponds, fermentation zone and composting final products. HEV was detected by reverse transcription polymerase chain reaction (RT-nested PCR) in four (80%) of five plants studied, mainly in the first stages of the process. HEV was not detected in any final product (compost) sample, destined to be commercialized as a soil fertilizer, suggesting that composting is a suitable method to eliminate HEV and thus, to reduce the transmission of HEV from pigs to humans. PMID:24206540

  10. Photosynthetic kinetics determine the outcome of competition for dissolved inorganic carbon by freshwater microalgae: implications for acidified lakes.

    PubMed

    Williams, T G; Turpin, D H

    1987-09-01

    Photosynthetic kinetics with respect to dissolved inorganic carbon were used to predict the outcome of competition for DIC between the green alga Selenastrum minutum and the cyanobacterium Synechococcus leopoliensis at pH 6.2, 7.5, and 10. Based on measured values of the maximum rate of photosynthesis, the half-saturation value of photosynthesis with respect to DIC (K 1(2/DIC) ), and the DIC compensation point, it was predicted that S. leopoliensis would lower the steady-state DIC concentration below the DIC compensation point of S. minutum. This should result in competitive displacement of the green alga at a rate equivalent to the chemostat dilution rate. This prediction was validated by carrying out competition experiments over the range of pH. These results suggest that the low levels of DIC in air-equilibrated acidified lakes may be an important rate-limiting resource and hence affect phytoplankton community structure. Furthermore, the low levels of DIC in these systems may be below the DIC compensation point for some species, thereby precluding their growth at acid pH solely as a function of DIC limitation. The potential importance of DIC in shaping phytoplankton community structure in acidified systems is discussed.

  11. Assessment of the relationship among acidifying depositions, surface water acidification, and fish populations in North America. Volume 1. Final report

    SciTech Connect

    Marcus, M.D.; Parkhurst, B.R.; Payne, F.E.

    1983-06-01

    This report assesses the scientific understanding about relationships between acidic depositions and freshwater aquatic resources. Selected surface waters in eastern North America are becoming acidified and fish populations are being eliminated. The actual extent of these resources threatened by acidification is now known. Mostly circumstantial evidence has been compiled to suggest that long-range atmospheric transport of acidifying compounds is causing surface-water acidification in North America. Certainly, atmospheric emissions from point sources can impact localized areas. However, some data indicate that atmospheric inputs of acids from long-range transport may add little to the natural flux of acids within ecosystems. The degree of influence that atmosphere depositions can have in accelerating natural acidification rates is unknown for most potentially sensitive surface waters. Fish losses appear to result from (1) long-term accumulations of acids and metals reaching chronically toxic concentrations; and (2) short-term, episodic events causing acutely toxic acid and metal concentrations. Some impacts may be successfully mitigated through several methods. Additional research is needed to (1) identify causes of surface-water acidification; (2) develop innovative mitigation measures; (3) define mechanisms of fish loss; and (4) establish the extent of aquatic resources at risk.

  12. Effects of calcite and magnesite application to a declining Masson pine forest on strongly acidified soil in Southwestern China.

    PubMed

    Huang, Yongmei; Kang, Ronghua; Ma, Xiaoxiao; Qi, Yu; Mulder, Jan; Duan, Lei

    2014-05-15

    Liming of strongly acidified soil under a Masson pine (Pinus massoniana Lamb.) forest was studied through a seven-year field manipulation experiment at Tieshanping, Chongqing in Southwestern China. To distinguish between the individual effects of Ca(2+) and Mg(2+) addition, we separately applied calcite (CaCO3) and magnesite (MgCO3), rather than using dolomite [CaMg(CO3)2]. Both calcite and magnesite additions caused a significant increase in pH and a decrease in dissolved inorganic monomeric aluminium (Ali) concentration of soil water. Ecological recovery included increases of herb biomass (both treatments) and Mg content in Masson pine needles (magnesite treatment only). However, the growth rate of Masson pine did not increase under either treatment, possibly because of nutrient imbalance due to phosphorus (P) deficiency or limited observation period. In China, acid deposition in forest ecosystems commonly coincides with large inputs of atmogenic Ca(2+), both enhancing Mg(2+) leaching. Calcite addition may further decrease the Mg(2+) availability in soil water, thereby exacerbating Mg(2+) deficiency in the acidified forest soils of southern and southwestern China. The effect of anthropogenic acidification of naturally acid forest soils on P availability needs further study.

  13. Coal slurry pump development. Final report, October 1, 1979-March 31, 1984

    SciTech Connect

    Wong, G.S.; Aukerman, R.E.

    1984-01-01

    A coal slurry pump development program for coal liquefaction was conducted by Rocketdyne Division, Rockwell International for the Department of Energy, Division of Fossil Fuel Processing. The program was initiated in October 1979 and consisted of fabrication and testing of a high-capacity, high-pressure, prototype, centrifugal slurry pump module that meets the following requiremennts for a coal/oil slurry with 50% concentration and 200 mesh coal: flowrate of 2500 gpm; operating pressure of 3000 psi; temperature of 550 F; pressure rise of 500 psi; a rotative speed of 3600 rpm; and a horsepower of 960. A two-stage, centrifugal slurry test pump was fabricated from steel castings and high wear-resistant materials for components exposed to slurry such as: cast white iron, titanium carbide, and tungsten carbide. A unique hydraulic design was utilized to reduce the severe wear on impeller and volute cutwater. The slurry pump incorporates a unique high-pressure, hydrostatic fluid seal capable of 3000 psi operating pressure. A slurry test facility for testing the centrifugal slurry pump was constructed at the Colorado School of Mines Research Institute (CSMRI), Golden, Colorado. The facility contains an 8-inch-diameter test loop, 1.7 million Btu/hr gas-fired oil heater, slurry head tank, boost pump, purge oil storage tank, high-pressure seal purge oil system, and a centrifuge/polishing filter system for recovering purge oil from the closed-loop coal slurry system. The prototype slurry pump successfully completed a three-phase hydraulic and wear test program in hot oil and hot coal/oil slurry, and achieved nearly continuous operation in slurry in excess of 242 hours with minimum wear. The feasibility of utilizing high-pressure centrifugal slurry pumps for coal liquefaction has been successfully demonstrated and further development is highly warranted. 73 figures, 19 tables.

  14. A scalable chemical route to soluble acidified graphitic carbon nitride: an ideal precursor for isolated ultrathin g-C3N4 nanosheets

    NASA Astrophysics Data System (ADS)

    Du, Xiaorui; Zou, Guojun; Wang, Zhonghao; Wang, Xiaolai

    2015-05-01

    We propose an efficient method to synthesize large-scale soluble acidified graphitic carbon nitride (g-C3N4). The as-prepared material exhibits the characteristics of a poly-ammonium salt and is soluble in several solvents with good dissolution-recrystallization reversible equilibrium. The pH value- and temperature-dependent solubility of the acidified g-C3N4 facilitates its separation and purification. After dissolution, acidified g-C3N4 forms isolated ultrathin nanosheets, making it an ideal precursor for large quantities of g-C3N4 nanosheets. This study raises the possibility of liquid assembly for g-C3N4 nanosheets based composite materials, expanding the functionalization and application of g-C3N4.We propose an efficient method to synthesize large-scale soluble acidified graphitic carbon nitride (g-C3N4). The as-prepared material exhibits the characteristics of a poly-ammonium salt and is soluble in several solvents with good dissolution-recrystallization reversible equilibrium. The pH value- and temperature-dependent solubility of the acidified g-C3N4 facilitates its separation and purification. After dissolution, acidified g-C3N4 forms isolated ultrathin nanosheets, making it an ideal precursor for large quantities of g-C3N4 nanosheets. This study raises the possibility of liquid assembly for g-C3N4 nanosheets based composite materials, expanding the functionalization and application of g-C3N4. Electronic supplementary information (ESI) available: Experimental details, supporting information for XRD and XPS analysis, FT-IR and UV-vis spectra of the recovered g-C3N4, EIS Nyquist plots, solubility experiments and results, TEM and AFM images of g-C3N4 nanosheets, and photographs and TEM images of Pt@CNS. See DOI: 10.1039/c5nr00665a

  15. Xenotransplantation and pig endogenous retroviruses.

    PubMed

    Magre, Saema; Takeuchi, Yasuhiro; Bartosch, Birke

    2003-01-01

    Xenotransplantation, in particular transplantation of pig cells, tissues and organs into human patients, may alleviate the current shortage of suitable allografts available for human transplantation. This overview addresses the physiological, immunological and virological factors considered with regard to xenotransplantation. Among the issues reviewed are the merits of using pigs as xenograft source species, the compatibility of pig and human organ physiology and the immunological hindrances with regard to the various types of rejection and attempts at abrogating rejection. Advances in the prevention of pig organ rejection by creating genetically modified pigs that are more suited to the human microenvironment are also discussed. Finally, with regard to virology, possible zoonotic infections emanating from pigs are reviewed, with special emphasis on the pig endogenous retrovirus (PERV). An in depth account of PERV studies, comprising their discovery as well as recent knowledge of the virus, is given. To date, all retrospective studies on patients with pig xenografts have shown no evidence of PERV transmission, however, many factors make us interpret these results with caution. Although the lack of PERV infection in xenograft recipients up to now is encouraging, more basic research and controlled animal studies that mimic the pig to human xenotransplantation setting more closely are required for safety assessment.

  16. RHEOLOGICAL AND ELEMENTAL ANALYSES OF SIMULANT SB5 SLURRY MIX EVAPORATOR-MELTER FEED TANK SLURRIES

    SciTech Connect

    Fernandez, A.

    2010-02-08

    The Defense Waste Processing Facility (DWPF) will complete Sludge Batch 5 (SB5) processing in fiscal year 2010. DWPF has experienced multiple feed stoppages for the SB5 Melter Feed Tank (MFT) due to clogs. Melter throughput is decreased not only due to the feed stoppage, but also because dilution of the feed by addition of prime water (about 60 gallons), which is required to restart the MFT pump. SB5 conditions are different from previous batches in one respect: pH of the Slurry Mix Evaporator (SME) product (9 for SB5 vs. 7 for SB4). Since a higher pH could cause gel formation, due in part to greater leaching from the glass frit into the supernate, SRNL studies were undertaken to check this hypothesis. The clogging issue is addressed by this simulant work, requested via a technical task request from DWPF. The experiments were conducted at Aiken County Technology Laboratory (ACTL) wherein a non-radioactive simulant consisting of SB5 Sludge Receipt and Adjustment Tank (SRAT) product simulant and frit was subjected to a 30 hour SME cycle at two different pH levels, 7.5 and 10; the boiling was completed over a period of six days. Rheology and supernate elemental composition measurements were conducted. The caustic run exhibited foaming once, after 30 minutes of boiling. It was expected that caustic boiling would exhibit a greater leaching rate, which could cause formation of sodium aluminosilicate and would allow gel formation to increase the thickness of the simulant. Xray Diffraction (XRD) measurements of the simulant did not detect crystalline sodium aluminosilicate, a possible gel formation species. Instead, it was observed that caustic conditions, but not necessarily boiling time, induced greater thickness, but lowered the leach rate. Leaching consists of the formation of metal hydroxides from the oxides, formation of boric acid from the boron oxide, and dissolution of SiO{sub 2}, the major frit component. It is likely that the observed precipitation of Mg

  17. Integrated system for coal-methanol liquefaction and slurry pipeline transportation. Final report. [In slurry transport

    SciTech Connect

    Banks, W.F.; Davidson, J.K.; Horton, J.H.; Summers, C.W.

    1980-03-31

    The engineering economics of an integrated coal-to-methanol conversion system and coal-in-methanol transportation system are examined, under the circumstances of the western coalfields, i.e., long distances from major markets and scarcity of water in the vicinity of the mines. The transportation economics are attractive, indicating tariffs of approximately 40 cents per million Btu per thousand miles for the coal-methanol pipeline vs 60 cents via coal-water pipelines and upwards of a dollar via rail. Energy consumption is also less in the coal-methanol pipeline than in the coal-water pipeline, and about equal to rail. It is also concluded that, by a proper marriage of the synthetic fuel (methanolization) plant to the slurrification plant, most, and in some cases all, of the water required by the synthetic fuel process can be supplied by the natural moisture of the coal itself. Thus, the only technology which presently exists and by which synthetic fuel from western coal can displace petroleum in the automotive fuel market is the integrated methanol conversion and tranportation system. The key element is the ability of the methanol slurry pipeline to accept and to deliver dry (1 to 5% moisture) coal, allowing the natural coal moisture to be used as synthesis feedstock in satisfaction of the large water requirement of any synthetic fuel plant. By virtue of these unique properties, this integrated system is seen as the only means in the foreseeable future whereby western coal can be converted to synthetic fuel and moved to distant markets.

  18. Corrosion inhibitors for water-base slurry in multiblade sawing

    NASA Technical Reports Server (NTRS)

    Chen, C. P.; Odonnell, T. P.

    1982-01-01

    The use of a water-base slurry instead of the standard PC oil vehicle was proposed for multiblade sawing (MBS) silicon wafering technology. Potential cost savings were considerable; however, significant failures of high-carbon steel blades were observed in limited tests using a water-based slurry during silicon wafering. Failures were attributed to stress corrosion. A specially designed fatigue test of 1095 steel blades in distilled water with various corrosion inhibitor solutions was used to determine the feasibility of using corrosion inhibitors in water-base MBS wafering. Fatigue tests indicate that several corrosion inhibitors have significant potential for use in a water-base MBS operation. Blade samples tested in these specific corrosion-inhibitor solutions exhibited considerably greater lifetime than those blades tested in PC oil.

  19. Feasibility of amending slurry walls with zero-valent iron

    SciTech Connect

    Rabideau, A.J.; Shen, P.; Khandelwal, A.

    1999-04-01

    Rapid degradation of aqueous trichloroethylene (TCE) was observed in batch experiments conducted with soil/bentonite slurry wall materials amended with the addition of zero-valent iron. The first-order TCE decay constants for soil/bentonite/iron mixtures, when normalized to the available iron surface area, were approximately 1--2 orders of magnitude higher than observed in batch experiments with pure iron systems. Permeability tests indicated an increase in SB hydraulic conductivity roughly proportional to the amount of iron added. Based on the observed reaction rates and the assumption of sustained long-term performance, significantly less than one percent added iron would be required to reduce the diffusive flux of TCE across an installed slurry wall by over 10 orders of magnitude. However, the release of hydrogen gas was noted as a potential problem for low permeability systems containing zero-valent iron.

  20. Critical parameters for coarse coal underground slurry haulage systems

    NASA Technical Reports Server (NTRS)

    Maynard, D. P.

    1981-01-01

    Factors are identified which must be considered in meeting the requirements of a transportation system for conveying, in a pipeline, the coal mined by a continuous mining machine to a storage location neat the mine entrance or to a coal preparation plant located near the surface. For successful operation, the slurry haulage the system should be designed to operated in the turbulent flow regime at a flow rate at least 30% greater than the deposition velocity (slurry flow rate at which the solid particles tend to settle in the pipe). The capacity of the haulage system should be compatible with the projected coal output. Partical size, solid concentration, density, and viscosity of the suspension are if importance as well as the selection of the pumps, pipes, and valves. The parameters with the greatest effect on system performance ar flow velocity, pressure coal particle size, and solids concentration.

  1. Planarization effect evaluation of acid and alkaline slurries in the copper interconnect process

    NASA Astrophysics Data System (ADS)

    Yi, Hu; Yan, Li; Yuling, Liu; Yangang, He

    2015-03-01

    We observed and analyzed the acid and HEBUT alkaline of Cu chemical mechanical polishing (CMP) slurry to evaluate their effects. Material analysis has shown that the planarity surfaces and the removal rate of alkaline slurry are better than the acid slurry during metal CMP processes. The global surface roughness and the small-scale surface roughness by 10 × 10 μm2 of copper film polished by the SVTC slurry are 1.127 nm and 2.49 nm. However, it is found that the surface roughnesses of copper films polished by the HEBUT slurry are 0.728 nm and 0.215 nm. All other things being equal, the remaining step heights of copper films polished by the SVTC slurry and HEBUT slurry are respectively 150 nm and 50 nm. At the end of the polishing process, the dishing heights of the HEBUT slurry and the SVTC slurry are approximately both 30 nm, the erosion heights of the HEBUT slurry and the SVTC slurry are approximately both 20 nm. The surface states of the copper film after CMP are tested, and the AFM results of two samples are obviously seen. The surface polished by SVTC slurry shows many spikes. This indicates that the HEBUT alkaline slurry is promising for inter-level dielectric (ILD) applications in ultra large-scale integrated circuits (ULSI) technology. Project supported by the Special Project Items No. 2 in National Long-Term Technology Development Plan (No. 2009ZX02308), the Doctoral Program Foundation of Xinjiang Normal University Plan (No. XJNUBS1226), the Key Laboratory of Coal Gasification, Ministry of Education, and the Inorganic Chemistry Key Disciplines of Xinjiang Normal University.

  2. Evaluation of anthracite as a coal-water slurry fuel. Final report

    SciTech Connect

    Not Available

    1985-02-01

    This study evaluated the use of anthracite as a coal-water slurry fuel. The study consisted of two major activities: (1) fundamental slurry formulation experiments leading to the production and combustion characteristics investigation of suitable, anthracite slurries, and (2) analytical evaluations of the potential of anthracite slurry as a boiler fuel for new industrial and utility boiler application and for retrofit application of an industrial oil-fired boiler. The study results have shown that anthracite can be readily processed into a coal-water slurry with coal loading 70 wt % coal and 30% water plus chemical additives. Slurry viscosity, handling, and storage characteristics are similar to the bituminous coal-water slurries that are under active commercial development. Commercial anthracite-water slurry processing cost is projected to be only slightly higher than for bituminous coal-water slurry. Combustion testing in a small, industrial, water-tube boiler has shown that stable combustion of anthracite-water slurry can be achieved with high carbon conversion. The results also indicate that oxygen enrichment and secondary fuel firing can compensate for the low volatile content of the anthracite to achieve good combustion. Under the conditions assumed, anthracite-water slurry was not an economical fuel retrofit option for an existing oil-fired, industrial boiler. Contributing significantly to the economic results were the requirement for secondary fuel and oxygen to achieve good anthracite slurry combustion in the oil-designed boiler. Minimizing or eliminating the secondary fuel and oxygen requirements through a continued burner/boiler development program or more radical boiler modification to fire low-volatile fuel would greatly improve conversion economics and likely make anthracite-water slurry a candidate for industrial boiler fuel retrofit. 10 refs., 22 figs., 38 tabs.

  3. Design of agitation systems in Bingham slurries by pilot simulation

    SciTech Connect

    Nielsen, M.G.

    1987-01-01

    A method was required to determine the optimum agitator speed needed to produce overall motion of the Defense Waste Processing Facility (DWPF) high-level waste slurries in remote process cell vessels. Project schedule and limited process space required an accurate determination of agitator horsepower and size without the benefit of full-scale testing. The small scale testing of unique clear rheologically similar fluid is described along with tests and scale-up procedures. 2 refs., 3 figs.

  4. Ice slurry on outdoor running performance in heat.

    PubMed

    Yeo, Z W; Fan, P W P; Nio, A Q X; Byrne, C; Lee, J K W

    2012-11-01

    The efficacy of ingestion of ice slurry on actual outdoor endurance performance is unknown. This study aimed to investigate ice slurry ingestion as a cooling intervention before a 10 km outdoor running time-trial. Twelve participants ingested 8 g · kg (- 1) of either ice slurry ( - 1.4°C; ICE) or ambient temperature drink (30.9°C; CON) and performed a 15-min warm-up prior to a 10 km outdoor running time-trial (Wet Bulb Globe Temperature: 28.2 ± 0.8°C). Mean performance time was faster with ICE (2 715 ± 396 s) than CON (2 730 ± 385 s; P=0.023). Gastrointestinal temperature (Tgi) reduced by 0.5 ± 0.2°C after ICE ingestion compared with 0.1 ± 0.1°C (P<0.001) with CON. During the run, the rate of rise in Tgi was greater (P=0.01) with ICE than with CON for the first 15 min. At the end of time-trial, Tgi was higher with ICE (40.2 ± 0.6°C) than CON (39.8 ± 0.4°C, P=0.005). Ratings of thermal sensation were lower during the cooling phase and for the first kilometre of the run ( - 1.2 ± 0.8; P<0.001). Although ingestion of ice slurry resulted in a transient increase in heat strain following a warm up routine, it is a practical and effective pre-competition cooling manoeuvre to improve performance in warm and humid environments.

  5. Oxyhalogen-sulfur chemistry: kinetics and mechanism of oxidation of captopril by acidified bromate and aqueous bromine.

    PubMed

    Kapungu, G P; Rukweza, G; Tran, Thai; Mbiya, Wilbes; Adigun, Risikat; Ndungu, Patrick; Martincigh, Bice; Simoyi, Reuben H

    2013-04-04

    By nature of their nucleophilicity, all thiol-based drugs are oxidatively metabolized in the physiological environment. The key to understanding the physiological role of a hypertension drug, (2S)-1-[(2S)-2-methyl-3-sulfanylpropanoyl]pyrrolidine-2-carboxylic acid, medically known as captopril is through studying its oxidation pathway: its reactive intermediates and oxidation products. The oxidation of captopril by aqueous bromine and acidified bromate has been studied by spectrophotometric and electrospray ionization techniques. The stoichiometry for the reaction of acidic bromate with captopril is 1:1, BrO3(-) + (C4H6N)(COOH)(COCHCH3CH2)-SH → (C4H6N)(COOH)(COCHCH3CH2)-SO3H + Br(-), with reaction occurring only at the thiol center. For the direct reaction of bromine with captopril, the ratio is 3:1; 3Br2 + (C4H6N)(COOH)(COCHCH3CH2)-SH + 3H2O → (C4H6N)(COOH)(COCHCH3CH2)-SO3H + 6HBr. In excess acidic bromate conditions the reaction displays an initial induction period followed by a sharp rise in absorbance at 390 nm due to rapid formation of bromine. The direct reaction of aqueous bromine with captopril was much faster than oxidation of the thiol by acidified bromate, with a bimolecular rate constant of (1.046 (±0.08) × 10(5) M(-1) s(-1). The detection of thiyl radicals confirms the involvement of radicals as intermediates in the oxidation of Captopril by acidified BrO3(-). The involvement of thiyl radicals in oxidation of captopril competes with a nonradical pathway involving 2-electron oxidations of the sulfur center. The oxidation product of captopril under these strong oxidizing conditions is a sulfonic acid as confirmed by electrospray ionization mass spectrometry (ESI-MS), iodometric titrations, and proton nuclear magnetic resonance ((1)H NMR) results. There was no evidence from ESI-MS for the formation of the sulfenic and sulfinic acids in the oxidation pathway as the thiol group is rapidly oxidized to the sulfonic acid. A computer simulation analysis of

  6. Acidified bile acids enhance tumor progression and telomerase activity of gastric cancer in mice dependent on c-Myc expression.

    PubMed

    Wang, Xiaolong; Sun, Lei; Wang, Xijing; Kang, Huafeng; Ma, Xiaobin; Wang, Meng; Lin, Shuai; Liu, Meng; Dai, Cong; Dai, Zhijun

    2017-03-01

    c-Myc overexpression has been implicated in several malignancies including gastric cancer. Here, we report that acidified bile acids enhance tumor progression and telomerase activity in gastric cancer via c-Myc activation both in vivo and in vitro. c-Myc mRNA and protein levels were assessed in ten primary and five local recurrent gastric cancer samples by quantitative real-time polymerase chain reaction and western blotting analysis. The gastric cancer cell line MGC803 was exposed to bile salts (100 μmol/L glycochenodeoxycholic acid and deoxycholic acid) in an acid medium (pH 5.5) for 10 min daily for 60 weeks to develop an MGC803-resistant cell line. Control MGC803 cells were grown without acids or bile salts for 60 weeks as a control. Cell morphology, proliferation, colony formation and apoptosis of MGC803-resistant cells were analyzed after 60 weeks. To determine the involvement of c-Myc in tumor progression and telomere aging in MGC803-resistant cells, we generated xenografts in nude mice and measured xenograft volume and in vivo telomerase activity. The c-Myc and hTERT protein and mRNA levels were significantly higher in local recurrent gastric cancer samples than in primary gastric cancer samples. MGC803-resistant cells showed a marked phenotypic change under normal growth conditions with more clusters and acini, and exhibited increased cell viability and colony formation and decreased apoptosis in vitro. These phenotypic changes were found to be dependent on c-Myc activation using the c-Myc inhibitor 10058-F4. MGC803-resistant cells also showed a c-Myc-dependent increase in xenograft growth and telomerase activity in vivo. In conclusion, these observations support the hypothesis that acidified bile acids enhance tumor progression and telomerase activity in gastric cancer and that these effects are dependent on c-Myc activity. These findings suggest that acidified bile acids play an important role in the malignant progression of local recurrent

  7. Reductive dechlorination of chlorobenzenes in surfactant-amended sediment slurries

    SciTech Connect

    Van Hoof, P.L.; Jafvert, C.T.

    1996-11-01

    Microbial anaerobic dechlorination of hexachlorobenzene (HCB) was examined in sediment slurries amended with two classes of nonionic surfactant, polyoxyethylene (POE) sorbitan fatty acid esters (Tweens) and POE alcohols (Brijs). The rationale for surfactant addition was to increase the bioavailability of highly sorbed organic pollutants to degrading microorganisms by enhancing their solubility. The solubility of HCB was initially enhanced via micellar partitioning; however, primary degradation of most surfactants occurred within 10 d. Dechlorination activity was significantly reduced at POE alcohol concentrations above the critical micelle concentration (cmc), with or without the occurrence of surfactant degradation. Tween 80 decreased HCB dechlorination at concentrations significantly above the cmc. At concentrations closer to the cmc, Tween 80 increased dechlorination rate constants four- to fivefold in acclimated slurries. Additions of Tween 80 at or below the cmc stimulated dechlorination activity in unacclimated slurries that exhibited very little activity in unamended controls. An average of 89% of HCB was dechlorinated after 90 d, compared to 20% in unamended sediments. No effect was observed for POE alcohols at these sub-cmc levels. The lack of a stimulated response for the POE alcohols suggests that Tween 80 may not be acting simply as a source of carbon or energy.

  8. Superheated fuel injection for combustion of liquid-solid slurries

    DOEpatents

    Robben, Franklin A.

    1985-01-01

    A method and device for obtaining, upon injection, flash evaporation of a liquid in a slurry fuel to aid in ignition and combustion. The device is particularly beneficial for use of coal-water slurry fuels in internal combustion engines such as diesel engines and gas turbines, and in external combustion devices such as boilers and furnaces. The slurry fuel is heated under pressure to near critical temperature in an injector accumulator, where the pressure is sufficiently high to prevent boiling. After injection into a combustion chamber, the water temperature will be well above boiling point at a reduced pressure in the combustion chamber, and flash boiling will preferentially take place at solid-liquid surfaces, resulting in the shattering of water droplets and the subsequent separation of the water from coal particles. This prevents the agglomeration of the coal particles during the subsequent ignition and combustion process, and reduces the energy required to evaporate the water and to heat the coal particles to ignition temperature. The overall effect will be to accelerate the ignition and combustion rates, and to reduce the size of the ash particles formed from the coal.

  9. Process for gasifying carbonaceous material from a recycled condensate slurry

    DOEpatents

    Forney, Albert J.; Haynes, William P.

    1981-01-01

    Coal or other carbonaceous material is gasified by reaction with steam and oxygen in a manner to minimize the problems of effluent water stream disposal. The condensate water from the product gas is recycled to slurry the coal feed and the amount of additional water or steam added for cooling or heating is minimized and preferably kept to a level of about that required to react with the carbonaceous material in the gasification reaction. The gasification is performed in a pressurized fluidized bed with the coal fed in a water slurry and preheated or vaporized by indirect heat exchange contact with product gas and recycled steam. The carbonaceous material is conveyed in a gas-solid mixture from bottom to top of the pressurized fluidized bed gasifier with the solids removed from the product gas and recycled steam in a supported moving bed filter of the resulting carbonaceous char. Steam is condensed from the product gas and the condensate recycled to form a slurry with the feed coal carbonaceous particles.

  10. Superheated fuel injection for combustion of liquid-solid slurries

    DOEpatents

    Robben, F.A.

    1984-10-19

    A method and device are claimed for obtaining, upon injection, flash evaporation of a liquid in a slurry fuel to aid in ignition and combustion. The device is particularly beneficial for use of coal-water slurry fuels in internal combustion engines such as diesel engines and gas turbines, and in external combustion devices such as boilers and furnaces. The slurry fuel is heated under pressure to near critical temperature in an injector accumulator, where the pressure is sufficiently high to prevent boiling. After injection into a combustion chamber, the water temperature will be well above boiling point at a reduced pressure in the combustion chamber, and flash boiling will preferentially take place at solid-liquid surfaces, resulting in the shattering of water droplets and the subsequent separation of the water from coal particles. This prevents the agglomeration of the coal particles during the subsequent ignition and combustion process, and reduces the energy required to evaporate the water and to heat the coal particles to ignition temperature. The overall effect will be to accelerate the ignition and combustion rates, and to reduce the size of the ash particles formed from the coal. 2 figs., 2 tabs.

  11. Surface Modification of Nickel Foams by a Slurry Aluminizing Process

    SciTech Connect

    Omar, H.; Papanastasiou, N.; Psyllaki, P.; Stergioudi, F.; Tsipas, D. N.; Tsipas, S. A.; Michailidis, N.

    2010-01-21

    A novel slurry-based process for aluminizing nickel foams while improving the mechanical properties and conserving the excellent ductility is reported. Cellular unalloyed nickel foams with 92% porosity and uniform pore size and distribution were used as a starting material. Several slurries of different compositions were examined to investigate the possibility of developing an aluminide-nickel intermetallic coating on a Ni foam without considerably degrading the original ductile properties of the foam. The process temperature was varying from 400 to 850 deg. C and the process holding time was ranging between 2h to 6h. Scanning electron microscopy with an energy dispersive X-ray spectrometry and X-Ray diffraction were applied to assess the effectiveness of the aluminizing process and determine both the optimum parameters of the procedure (slurry composition, holding temperature and time) and the concentration profiles across the coating cross-section. The mechanical behavior of the aluminized Ni-foams was evaluated by the conduction of micro-tension tests. The resulting Ni-foams after aluminization retain the pore structure of original Ni-foams and present a thick outer surface layer which consists of a range of aluminide phases. The mechanical properties of the Ni-foams aluminized in low process temperature were insignificantly affected.

  12. Rheology of slurries and environmental impacts in the mining industry.

    PubMed

    Boger, David V

    2013-01-01

    The world's resource industries are the largest producers of waste. Much of this waste is produced as a fine particle slurry, which is pumped to a storage area, generally at a low concentration, where it behaves like a Newtonian fluid. Simply removing, reusing, and recycling water from the slurry represents a step toward a more sustainable practice in this industry. As the concentration of such a slurry is increased as a result of dewatering, the materials exhibit non-Newtonian behavior, which is characterized by shear thinning, a yield stress, and in some instances thixotropic behavior. Such high-concentration, nonideal (dirty) suspensions in the resource industries have meant that new rheological methods and techniques have been needed to measure and interpret the basic flow properties. Also, some older empirical techniques have needed to be modified and interpreted in a more fundamental way so that the results could be used in design. This article reviews these techniques and illustrates how the industry itself has motivated their development. Understanding and exploiting this rheology has resulted in dramatic improvement in the waste-disposal strategy for some industries, but many have failed to embrace the available technology. The reasons for this are discussed. The article concludes that a greater positive change in waste-management practice will occur in the future, motivated by several factors, including public perception, tighter regulation, and perhaps even commonsense life cycle accounting.

  13. Additive for coal water slurry made from weak slurryability coal

    SciTech Connect

    Zi-xiu Zang; Lin Zhang; Xino-an Fu; Long Jiang

    1993-12-31

    Surface treatment of weak slurryability coal and preparation of highly concentrated coal water slurry (CWS) have been investigated using wettability and rheology measurements. By adding 0.5{approximately}10 wt.% (based on coal) pitch during dry milling coal surface became more hydrophobic and the coal could be easily prepared for CWS which had much lower viscosity compared with CWS of the untreated coal. The reasons of this result is high degree of hydrophobic surface of coal particles made surfactant adsorption easier compared with high degree of hydrophilic surface of coal particles. Another important reason in hydrophobic surface impeded the penetration of water into the inner pores of coal particles which resulted in decreasing swelling ability of coal and enhancing the fluidity of CWS. Four different additives have been investigated including three nonionic ethoxylated surfactants and one mixture of anionic surfactants (sodium humate derivative and naphthalenesulfonic acid-HCHO condensate). Both rheological and thixotropic properties showed that nonionic surfactant G2 was the most efficient additive for preparation of highly concentrated CWS. The results of dynamic experiment illustrated that the slurry had good dynamic stability, in other words, the viscosity of the slurry decreased very slowly at constant stir. The pitch treated coal powders were beneficiated coal had much lower viscosity compared with CWS of the unbeneficiated coal.

  14. Determination of 5-log reduction times for Escherichia coli O157:H7, Salmonella enterica, or Listeria monocytogenes in acidified foods with pH 3.5 or 3.8

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A critical factor in ensuring the safety of acidified foods is the establishment of a thermal process that assures the destruction of acid-resistant vegetative pathogenic and spoilage bacteria. For acidified foods such as dressings and mayonnaises with pH values of 3.5 or higher, the high water phas...

  15. Microwave assisted esterification of acidified oil from waste cooking oil by CERP/PES catalytic membrane for biodiesel production.

    PubMed

    Zhang, Honglei; Ding, Jincheng; Zhao, Zengdian

    2012-11-01

    The traditional heating and microwave assisted method for biodiesel production using cation ion-exchange resin particles (CERP)/PES catalytic membrane were comparatively studied to achieve economic and effective method for utilization of free fatty acids (FFAs) from waste cooking oil (WCO). The optimal esterification conditions of the two methods were investigated and the experimental results showed that microwave irradiation exhibited a remarkable enhanced effect for esterification compared with that of traditional heating method. The FFAs conversion of microwave assisted esterification reached 97.4% under the optimal conditions of reaction temperature 60°C, methanol/acidified oil mass ratio 2.0:1, catalytic membrane (annealed at 120°C) loading 3g, microwave power 360W and reaction time 90min. The study results showed that it is a fast, easy and green way to produce biodiesel applying microwave irradiation.

  16. Bioremediation of solid TNT particles in a soil slurry reactor: Mass transfer considerations

    SciTech Connect

    Gilcrease, P.C.; Murphy, V.G.; Reardon, K.F.

    1996-12-31

    The bioreduction of solid TNT by a Pseudomonas fluorescens strain was investigated in a stirred tank reactor. Experiments in which TNT beads were the only solids present indicated that the biodegradation mechanism is dissolution followed by degradation in bulk solution. Dissolution may limit the overall rate, in which case degradation can be enhanced through increased agitation. Since soil slurries may contain high concentrations of solids other than TNT, Teflon chips were added to investigate two separate effects on TNT dissolution in slurries. First, Teflon solids increase the viscosity of the slurry, resulting in lower solid-liquid mass transfer coefficients. Second, the agitated Teflon slurry can grind or comminute TNT particles, creating additional surface area for mass transfer. Enhanced dissolution rates were observed for TNT beads in a Teflon slurry at higher agitator speeds. This suggests that the biodegradation of solid TNT nuggets in a soil slurry bioreactor may be enhanced under conditions that promote particle attrition.

  17. Analysis of the polishing slurry flow of chemical mechanical polishing by polishing pad with phyllotactic pattern

    NASA Astrophysics Data System (ADS)

    Lv, Yushan; Zhang, Tian; Wang, Jun; Li, Nan; Duan, Min; Xing, Xue-Ling

    2010-12-01

    In order to make the polishing slurry distribution more uniform over the polishing region, a new kind of polishing pad, which has sunflower seed pattern, has been designed based on the phyllotaxis theory of biology, and the boundary conditions of polishing slurry flow have been established. By the help of computational fluid dynamics software (FLUENT), the flow state of the polishing slurry is simulated and the effects of the phyllotactic parameters of polishing pad on the flow field of polishing slurry are analyzed. The results show that when the polishing slurry is imported from the center of phyllotaxis polishing pad, the slurry flows along the counterclockwise and clockwise spiral grooves of phyllotatic pattern, which make fluid flow divergence around, and the flow field becomes more uniform.

  18. A low-cost solid-liquid separation process for enzymatically hydrolyzed corn stover slurries.

    PubMed

    Sievers, David A; Lischeske, James J; Biddy, Mary J; Stickel, Jonathan J

    2015-01-01

    Solid-liquid separation of intermediate process slurries is required in some process configurations for the conversion of lignocellulosic biomass to transportation fuels. Thermochemically pretreated and enzymatically hydrolyzed corn stover slurries have proven difficult to filter due to formation of very low permeability cakes that are rich in lignin. Treatment of two different slurries with polyelectrolyte flocculant was demonstrated to increase mean particle size and filterability. Filtration flux was greatly improved, and thus scaled filter unit capacity was increased approximately 40-fold compared with unflocculated slurry. Although additional costs were accrued using polyelectrolyte, techno-economic analysis revealed that the increase in filter capacity significantly reduced overall production costs. Fuel production cost at 95% sugar recovery was reduced by $1.35 US per gallon gasoline equivalent for dilute-acid pretreated and enzymatically hydrolyzed slurries and $3.40 for slurries produced using an additional alkaline de-acetylation preprocessing step that is even more difficult to natively filter.

  19. Nitrogen and phosphorus removal coupled with carbohydrate production by five microalgae cultures cultivated in biogas slurry.

    PubMed

    Tan, Fen; Wang, Zhi; Zhouyang, Siyu; Li, Heng; Xie, Youping; Wang, Yuanpeng; Zheng, Yanmei; Li, Qingbiao

    2016-12-01

    In this study, five microalgae strains were cultured for their ability to survive in biogas slurry, remove nitrogen resources and accumulate carbohydrates. It was proved that five microalgae strains adapted in biogas slurry well without ammonia inhibition. Among them, Chlorella vulgaris ESP-6 showed the best performance on carbohydrate accumulation, giving the highest carbohydrate content of 61.5% in biogas slurry and the highest ammonia removal efficiency and rate of 96.3% and 91.7mg/L/d respectively in biogas slurry with phosphorus and magnesium added. Additionally, the absence of phosphorus and magnesium that can be adverse for biomass accumulation resulted in earlier timing of carbohydrate accumulation and magnesium was firstly recognized and proved as the influence factor for carbohydrate accumulation. Microalgae that cultured in biogas slurry accumulated more carbohydrate in cell, making biogas slurry more suitable medium for the improvement of carbohydrate content, thus can be regarded as a new strategy to accumulate carbohydrate.

  20. Analysis of high-level radioactive slurries as a method to reduce DWPF turnaround times

    SciTech Connect

    Coleman, C.J.; Bibler, N.E.; Ferrara, D.M.; Hay, M.S.

    1996-06-01

    Analysis of Defense Waste Processing Facility (DWPF) samples as slurries rather than as dried or vitrified samples is an effective way to reduce sample turnaround times. Slurries can be dissolved with a mixture of concentrated acids to yield solutions for elemental analysis by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Slurry analyses can be performed in eight hours, whereas analyses of vitrified samples require up to 40 hours to complete. Analyses of melter feed samples consisting of the DWPF borosilicate frit and either simulated or actual DWPF radioactive sludge were typically within a range of 3--5% of the predicted value based on the relative amounts of sludge and frit added to the slurry. The results indicate that the slurry analysis approach yields analytical accuracy and precision competitive with those obtained from analyses of vitrified samples. Slurry analyses offer a viable alternative to analyses of solid samples as a simple way to reduce analytical turnaround times.

  1. A low-cost solid–liquid separation process for enzymatically hydrolyzed corn stover slurries

    SciTech Connect

    Sievers, David A.; Lischeske, James J.; Biddy, Mary J.; Stickel, Jonathan J.

    2015-07-01

    Solid-liquid separation of intermediate process slurries is required in some process configurations for the conversion of lignocellulosic biomass to transportation fuels. Thermochemically pretreated and enzymatically hydrolyzed corn stover slurries have proven difficult to filter due to formation of very low permeability cakes that are rich in lignin. Treatment of two different slurries with polyelectrolyte flocculant was demonstrated to increase mean particle size and filterability. Filtration flux was greatly improved, and thus scaled filter unit capacity was increased approximately 40-fold compared with unflocculated slurry. Although additional costs were accrued using polyelectrolyte, techno-economic analysis revealed that the increase in filter capacity significantly reduced overall production costs. Fuel production cost at 95% sugar recovery was reduced by $1.35 US per gallon gasoline equivalent for dilute-acid pretreated and enzymatically hydrolyzed slurries and $3.40 for slurries produced using an additional alkaline de-acetylation preprocessing step that is even more difficult to natively filter.

  2. Experimental investigation of an applicator of liquid slurry, from biogas production, for crop production.

    PubMed

    Kurchania, A K; Panwar, N L

    2011-01-01

    A unit for the application of liquid digested slurry in the field was designed and developed. The developed slurry applicator had a capacity of 1500 L and was pulled by a 35 h.p. tractor. The liquid digested slurry of a biogas plant was pumped in to the tank with the help of a slurry pump. The necessary power transmission system, consisting of a pulley, power take off shaft (PTO) and cross joints, was provided to get power from the PTO of the tractor. In this paper an attempt has been made to evaluate the application of liquid slurry in the field in terms of plant growth parameters such as number of branches/plant, number of nodules/plant, plant height and yield attributes like pods/plant and grains/pod. The application of liquid slurry resulted in an increase in grain, straw and biological yields of 32%, 7% and 15%, respectively, compared with the application of farmyard manure.

  3. Application of Impedance Microbiology for Evaluating Potential Acidifying Performances of Starter Lactic Acid Bacteria to Employ in Milk Transformation.

    PubMed

    Bancalari, Elena; Bernini, Valentina; Bottari, Benedetta; Neviani, Erasmo; Gatti, Monica

    2016-01-01

    Impedance microbiology is a method that enables tracing microbial growth by measuring the change in the electrical conductivity. Different systems, able to perform this measurement, are available in commerce and are commonly used for food control analysis by mean of measuring a point of the impedance curve, defined "time of detection." With this work we wanted to find an objective way to interpret the metabolic significance of impedance curves and propose it as a valid approach to evaluate the potential acidifying performances of starter lactic acid bacteria to be employed in milk transformation. To do this it was firstly investigated the possibility to use the Gompertz equation to describe the data coming from the impedance curve obtained by mean of BacTrac 4300®. Lag time (λ), maximum specific M% rate (μmax), and maximum value of M% (Yend) have been calculated and, given the similarity of the impedance fitted curve to the bacterial growth curve, their meaning has been interpreted. Potential acidifying performances of eighty strains belonging to Lactobacillus helveticus, Lactobacillus delbrueckii subsp. bulgaricus, Lactococcus lactis, and Streptococcus thermophilus species have been evaluated by using the kinetics parameters, obtained from Excel add-in DMFit version 2.1. The novelty and importance of our findings, obtained by means of BacTrac 4300®, is that they can also be applied to data obtained from other devices. Moreover, the meaning of λ, μmax, and Yend that we have extrapolated from Modified Gompertz equation and discussed for lactic acid bacteria in milk, can be exploited also to other food environment or other bacteria, assuming that they can give a curve and that curve is properly fitted with Gompertz equation.

  4. Application of Impedance Microbiology for Evaluating Potential Acidifying Performances of Starter Lactic Acid Bacteria to Employ in Milk Transformation

    PubMed Central

    Bancalari, Elena; Bernini, Valentina; Bottari, Benedetta; Neviani, Erasmo; Gatti, Monica

    2016-01-01

    Impedance microbiology is a method that enables tracing microbial growth by measuring the change in the electrical conductivity. Different systems, able to perform this measurement, are available in commerce and are commonly used for food control analysis by mean of measuring a point of the impedance curve, defined “time of detection.” With this work we wanted to find an objective way to interpret the metabolic significance of impedance curves and propose it as a valid approach to evaluate the potential acidifying performances of starter lactic acid bacteria to be employed in milk transformation. To do this it was firstly investigated the possibility to use the Gompertz equation to describe the data coming from the impedance curve obtained by mean of BacTrac 4300®. Lag time (λ), maximum specific M% rate (μmax), and maximum value of M% (Yend) have been calculated and, given the similarity of the impedance fitted curve to the bacterial growth curve, their meaning has been interpreted. Potential acidifying performances of eighty strains belonging to Lactobacillus helveticus, Lactobacillus delbrueckii subsp. bulgaricus, Lactococcus lactis, and Streptococcus thermophilus species have been evaluated by using the kinetics parameters, obtained from Excel add-in DMFit version 2.1. The novelty and importance of our findings, obtained by means of BacTrac 4300®, is that they can also be applied to data obtained from other devices. Moreover, the meaning of λ, μmax, and Yend that we have extrapolated from Modified Gompertz equation and discussed for lactic acid bacteria in milk, can be exploited also to other food environment or other bacteria, assuming that they can give a curve and that curve is properly fitted with Gompertz equation. PMID:27799925

  5. Effects of acetic acid and arginine on pH elevation and growth of Bacillus licheniformis in an acidified cucumber juice medium

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Bacillus licheniformis has been shown to cause pH elevation in tomato products having an initial pH below 4.6 and metabiotic effects that can lead to the growth of pathogenic bacteria. Because of this, the organism poses a potential risk to acidified vegetable products; however, little is known abou...

  6. Preservation of acidified cucumbers with a natural preservative combination of fumaric acid and allyl isothiocyanate that target lactic acid bacteria and yeasts

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Without the addition of preservative compounds cucumbers acidified with 150 mM acetic acid with pH adjusted to 3.5 typically undergo fermentation by lactic acid bacteria. Fumaric acid (20 mM) inhibited growth of Lactobacillus plantarum and the lactic acid bacteria present on fresh cucumbers, but sp...

  7. Effect of plastic viscosity and yield value on spray characteristics of magnesium-slurry fuel

    NASA Technical Reports Server (NTRS)

    Prok, George M

    1957-01-01

    Magnesium slurries were sprayed onto a sheet of paper from an air-atomizing injector. Drop sizes and distributions were then determined from photomicrographs. Four different surface-active additives were used in preparing the slurries to give plastic viscosities between 0.22 and 0.51 poise and yield values between 150 and 810 dynes-cm(exp 2). It was found that there was no significant variation in the spray characteristics of these slurries when tested under the same conditions.

  8. Evaluation of Single Column Trapping/Separation and Chemiluminescence Detection for Measurement of Methanethiol and Dimethyl Sulfide from Pig Production

    PubMed Central

    Hansen, Michael Jørgen; Toda, Kei; Obata, Tomoaki; Adamsen, Anders Peter S.; Feilberg, Anders

    2012-01-01

    Reduced sulfur compounds are considered to be important odorants from pig production due to their low odor threshold values and low solubility in slurry. The objective of the present study was to investigate the use of a portable method with a single silica gel column for trapping/separation coupled with chemiluminescence detection (SCTS-CL) for measurement of methanethiol and dimethyl sulfide in sample air from pig production. Proton-transfer-reaction mass spectrometry (PTR-MS) was used to evaluate the trapping/separation. The silica gel column used for the SCTS-CL efficiently collected hydrogen sulfide, methanethiol and dimethyl sulfide. The measurement of methanethiol by SCTS-CL was clearly interfered by the high concentration of hydrogen sulfide found in pig production, and a removal of hydrogen sulfide was necessary to obtain reliable results. Air samples taken from a facility with growing-finishing pigs were analyzed by SCTS-CL, PTR-MS, and a gas chromatograph with sulfur chemiluminescence detection (GC-SCD) to evaluate the SCTS-CL. The difference between the concentrations of methanethiol and dimethyl sulfide measured with SCTS-CL, PTR-MS, and GC-SCD was below 10%. In conclusion, the SCTS-CL is a portable and low-cost alternative to the commercial methods that can be used to measure methanethiol and dimethyl sulfide in sample air from pig production. PMID:22997603

  9. Evaluation of single column trapping/separation and chemiluminescence detection for measurement of methanethiol and dimethyl sulfide from pig production.

    PubMed

    Hansen, Michael Jørgen; Toda, Kei; Obata, Tomoaki; Adamsen, Anders Peter S; Feilberg, Anders

    2012-01-01

    Reduced sulfur compounds are considered to be important odorants from pig production due to their low odor threshold values and low solubility in slurry. The objective of the present study was to investigate the use of a portable method with a single silica gel column for trapping/separation coupled with chemiluminescence detection (SCTS-CL) for measurement of methanethiol and dimethyl sulfide in sample air from pig production. Proton-transfer-reaction mass spectrometry (PTR-MS) was used to evaluate the trapping/separation. The silica gel column used for the SCTS-CL efficiently collected hydrogen sulfide, methanethiol and dimethyl sulfide. The measurement of methanethiol by SCTS-CL was clearly interfered by the high concentration of hydrogen sulfide found in pig production, and a removal of hydrogen sulfide was necessary to obtain reliable results. Air samples taken from a facility with growing-finishing pigs were analyzed by SCTS-CL, PTR-MS, and a gas chromatograph with sulfur chemiluminescence detection (GC-SCD) to evaluate the SCTS-CL. The difference between the concentrations of methanethiol and dimethyl sulfide measured with SCTS-CL, PTR-MS, and GC-SCD was below 10%. In conclusion, the SCTS-CL is a portable and low-cost alternative to the commercial methods that can be used to measure methanethiol and dimethyl sulfide in sample air from pig production.

  10. Technology And Pregnant Pigs

    NASA Technical Reports Server (NTRS)

    1978-01-01

    One of the interesting things about aerospace spinoff is the way it keeps cropping up in uncommon applications unimaginably remote from the original technology. For example, the pig pregnancy detector. The pig pregnancy detector? City folk may be surprised to learn that there is such a thing-and wonder why. The why is because it is a sow's job to produce piglets and farmers can't afford to keep those who don't; it costs about a half-dollar a day in feed, labor and facilities, and even in small herds that's intolerable. So the barren sow must go. Until recently, the best method of determining pig pregnancy was "eyeballing," daily visual examination over a period of time. The problem with eyeballing is that pregnancy is not evident until well advanced; when there is no pregnancy, the farmer learns too late that he has been feeding a sow that won't give him a litter. Advancing technology provided an answer: the quick, easy-to-use, accurate automatic detector for early evaluation of pregnancy status. Among the most popular of these devices are Scanopreg and Scanoprobe, to whose development NASA technology contributed. Scanopreg is an ultrasonic system which detects pregnancy about 30 days after breeding, long before eyeballing can provide an answer. The companion Scanoprobe is a dual-function unit which not only determines pregnancy but also gives farmers an analysis of a hog's meat-fat ratio, an important factor in breeding. Only a short time on the market, Scanopreg and Scanoprobe have already found wide acceptance among meat producers because they rapidly repay their cost.

  11. Piston diaphragm pumps an economic and reliable tool for slurry pipeline transportation

    SciTech Connect

    Broek, B. van den

    1998-04-01

    Slurry transportation systems by means of pumps and pipelines has been in use now for over 100 years. Hydraulic transportation of slurries is defined as a two-phase transportation of a mixture of a fluid carrier and solids, mainly in enclosed pipelines. In the mid fifties, slurry transportation techniques became more sophisticated, resulting in the design and operation of long distance pipe-lines for raw materials, such as coal, copper concentrate, iron concentrate, kaolin and phosphate. Nowadays, slurry transportation through pipelines has become a generally accepted means of solids transportation.

  12. Experiments on densely-loaded non-Newtonian slurries in laminar and turbulent pipe flows

    NASA Astrophysics Data System (ADS)

    Mannheimer, R. J.; Grimley, T. A.; Park, J. T.; Morrow, T. B.

    1987-04-01

    The structure of non-Newtonian slurries in laminar, transitional, and turbulent flow regimes in pipes is studied. Experiments are conducted in a large-scale pipe slurry flow facility with an inside pipe diameter of 51 mm. Flow measurements including turbulence quantities such as Reynolds stress are taken with a two-component laser-Doppler velocimeter in a transparent test section with a transparent model slurry. Two transparent model slurries have been developed with non-Newtonian rheological properties. Silica gel particles with diameters on the order of one micron are suspended in two different hydrocarbon liquid mixtures with viscosities of 1.19 and 6.39 cS. In rheological measurements with a concentric cylinder viscometer, slurries from both liquid mixtures exhibited slip. From a linear regression analysis with a power-law model, slurries with the higher viscosity fluid had yield values of 80 and 30 dyn/sq cm for silica gel concentrations of 5.6 and 4.0% by weight, respectively, and the exponents were 0.584 and 0.763. The measured refractive index for the transparent slurries is 1.454 where the difference in refractive index between the fluid and silica gel is estimated to be less than 0.001. Bench scale tests with large diameter silica gel particles on the order of 100 microns have produced slurries with excessive turbidity. A silica gel manufactured by a different process which may form a less turbid slurry is currently under investigation.

  13. Management of root-knot nematode in tomato Lycopersicon esculentum, Mill, with biogas slurry.

    PubMed

    Jothi, G; Pugalendhi, S; Poornima, K; Rajendran, G

    2003-09-01

    The effect of biogas slurry application on the severity of root-knot nematode, Meloidogyne incognita, attack on tomato cv. Co-1, was tested in the green house with two levels of biogas slurry: 5% and 10% (w/w) added to soil. Both the number (3 fruits/plant) and fruit yield (35.2 g/plant) of tomato increased significantly with 10% (w/w) biogas slurry. The plants amended with biogas slurry put up more vegetative growth and tended to flower and fruit much earlier than did those of the control. The nematode population in the soil decreased thus decreasing the severity of nematode attack.

  14. Study On Numerical Simulation And Experiment Of Fabrication Magnesium Semisolid Slurry By Damper Cooling Tube Method

    NASA Astrophysics Data System (ADS)

    Xie, Shuisheng; Huang, Guojie; Zhang, Xiaoli; Yang, Haoqiang

    2007-05-01

    Damper Cooling Tube (DCT) Method to fabricate the semi-solid metal slurry has been studied in this paper. Firstly, numerical simulation is adopted to investigate the flow process in order to optimize the technical parameters. The temperature effects on the rheological properties of the slurries are also considered. The effects of technical parameters on the slurry properties are studied in detail. Then the experiment was carried out with AZ91 magnesium alloy in order to examine the numerical simulation results. The results of numerical simulation are consistent with the experimental results. According to the numerical and experiment results, the DCT device can fabricate fine semisolid slurry with primary globular phase.

  15. Effect of Surface-active Additives on Physical Properties of Slurries of Vapor-process Magnesium

    NASA Technical Reports Server (NTRS)

    Pinns, Murray L

    1955-01-01

    The presence of 3 to 5 percent surface-active additive gave the lowest Brookfield apparent viscosity, plastic viscosity, and yield value that were obtained for slurry fuels containing approximately 50 percent vapor-process magnesium in JP-1 fuel. The slurries settled little and were easily remixed. A polyoxyethylene dodecyl alcohol was the most effective of 13 additives tested in reducing the Brookfield apparent viscosity and the yield value of the slurry. The seven most effective additives all had a hydroxyl group plus an ester or polyoxethylene group in the molecule. The densities of some of the slurries were measured.

  16. Precipitate hydrolysis process for the removal of organic compounds from nuclear waste slurries

    DOEpatents

    Doherty, Joseph P.; Marek, James C.

    1989-01-01

    A process for removing organic compounds from a nuclear waste slurry comprising reacting a mixture of radioactive waste precipitate slurry and an acid in the presence of a catalytically effective amount of a copper (II) catalyst whereby the organic compounds in the precipitate slurry are hydrolyzed to form volatile organic compounds which are separated from the reacting mixture. The resulting waste slurry, containing less than 10 percent of the orginal organic compounds, is subsequently blended with high level radioactive sludge and transferred to a virtrification facility for processing into borosilicate glass for long-term storage.

  17. Precipitate hydrolysis process for the removal of organic compounds from nuclear waste slurries

    DOEpatents

    Doherty, J.P.; Marek, J.C.

    1987-02-25

    A process for removing organic compounds from a nuclear waste slurry comprising reacting a mixture of radioactive waste precipitate slurry and an acid in the presence of a catalytically effective amount of a copper(II) catalyst whereby the organic compounds in the precipitate slurry are hydrolyzed to form volatile organic compounds which are separated from the reacting mixture. The resulting waste slurry, containing less than 10 percent of the original organic compounds, is subsequently blended with high level radioactive sludge land transferred to a vitrification facility for processing into borosilicate glass for long-term storage. 2 figs., 3 tabs.

  18. Evaluation of the transport and resuspension of a simulated nuclear waste slurry: Nuclear Waste Treatment Program

    SciTech Connect

    Carleson, T.E.; Drown, D.C.; Hart, R.E.; Peterson, M.E.

    1987-09-01

    The Department of Chemical Engineering at the University of Idaho conducted research on the transport and resuspension of a simulated high-level nuclear waste slurry. In the United States, the reference process for treating both defense and civilian HLLW is vitrification using the liquid-fed ceramic melter process. The non-Newtonian behavior of the slurry complicates the evaluation of the transport and resuspension characteristics of the slurry. The resuspension of a simulated (nonradioactive) melter feed slurry was evaluated using a slurry designated as WV-205. The simulated slurry was developed for the West Valley Demonstration Project and was used during a pilot-scale ceramic melter (PSCM) experiment conducted at PNL in July 1985 (PSCM-21). This study involved determining the transport characteristics of a fully suspended slurry and the resuspension characteristics of settled solids in a pilot-scale pipe loop. The goal was to predict the transport and resuspension of a full-scale system based on rheological data for a specific slurry. The rheological behavior of the slurry was evaluated using a concentric cylinder rotational viscometer, a capillary tube viscometer, and the pilot-scale pipe loop. The results obtained from the three approaches were compared. 40 refs., 74 figs., 15 tabs.

  19. Distribution and leaching ability of some heavy metals in products of flotation processing of fine-grained coal slurries

    SciTech Connect

    Klika, Z.; Weiss, Z.; Lach, K.

    1994-12-31

    Coal from the Ostrava-Karvina mines is processed in 19 coal preparation plants, 6 of which are not equipped with flotation technology. Generally, all fine-grained coal is transported into sedimentary coal slurry ponds. Depending on processing technology, coal slurries contain from 5 to 95% coal matter. Sedimentary coal slurry ponds occupy large areas, deteriorate the landscape, and ar great sources of dust in a dry summer. Moreover, some components from coal slurries scan be leached and can penetrate into underground water. This research project sampled 13 coal slurry ponds to determine the composition of coal slurries, the distribution of some heavy metals in the flotation process, and leaching behavior.

  20. Gaseous emissions during the fattening of pigs kept either on fully slatted floors or on straw flow.

    PubMed

    Philippe, F-X; Laitat, M; Canart, B; Vandenheede, M; Nicks, B

    2007-11-01

    The aim of this study was to compare the environmental impact of the straw-flow system for fattening pigs with the slatted-floor system by measuring pollutant gas emissions such as ammonia (NH3), nitrous oxide (N2O), methane (CH4) and carbon dioxide (CO2), manure nitrogen (N) content and emissions of water vapour (H2O). Three successive batches of 32 pigs were fattened. For each batch, pigs were allotted to two groups raised in separated rooms fitted either with a concrete totally slatted-floor system (0.75 m2 per pig) or with a straw-flow system (0.79 m2 per pig). With this last system, pigs were kept on a sloped floor, straw being provided daily at the top of the pen. Throughout the fattening period, about 34.4 kg of straw were supplied per pig. The straw, mixed with dung, travelled down the slope by pig motion and went out of the pen to a scraped passage. The solid fraction was scraped every day, stored in a heap in the room and removed every month, 1 week before each period of gaseous emission measurement. The liquid fraction was automatically pumped from the scraped passage into a hermetic tank, which was emptied at the end of each fattening period. Rooms were ventilated mechanically in order to maintain a constant ambient temperature. Once a month, the emissions of NH3, N2O, CH4, CO2 and H2O were measured hourly for 6 consecutive days via infrared photoacoustic detection. Mean daily emissions per pig fattened on the slatted floor or on the sloped floor were, respectively, 4.98 and 13.31 g NH3, 0.67 and 0.68 g N2O, 15.2 and 8.88 g CH4, 548 g and 406 g CO2 equivalents, 1.61 and 1.77 kg CO2 and 2.33 and 2.95 kg H2O. Except for N2O emissions, all the differences were statistically significant (P < 0.001). From the slatted-floor system, the amount of slurry removed per fattening period was on average 256 kg per pig. From the straw-flow system, solid manure amounted on average to 209 kg per pig and liquid manure to 53 kg per pig. The total N-content of the manure

  1. Microparticulate ICE slurry for renal hypothermia: laparoscopic partial nephrectomy in a porcine model.

    SciTech Connect

    Shikanov, S; Wille, M; Large, M; Razmaria, A; Lifshitz, D; Chang, A; Wu, Y; Kasza, K; Shalhav, A

    2010-10-01

    Previously, we described the feasibility of renal hypothermia using microparticulate ice slurry during laparoscopy. In the present study, we compared surface cooling with the ice slurry versus near-frozen saline or warm ischemia (WI) during laparoscopic partial nephrectomy (LPN) in a porcine model. We used a single-kidney porcine model. Animals in 5 equal groups (n = 6 each) underwent right laparoscopic complete nephrectomy. In Phase I, left LPN was performed under 90 minutes of ischemia and 90-minute renal cooling with either slurry (Slurry group 1) or saline (Saline group 1). No cooling was applied in the WI group. In Phase II, to simulate more extreme condition, ischemia time was extended to 120 minutes and cooling shortened to 10 minutes (Slurry group 2 and Saline group 2). The study endpoints were renal and core temperature during the surgery and serum creatinine at baseline and days 1, 3, 7, and 14 after the procedure. The ice slurry was easily produced and delivered. Nadir renal temperature (mean {+-} SD) was 8 {+-} 4 C in Slurry group 1 vs. 22.5 {+-} 3 C in Saline group 1 (P < .0001). Renal rewarming to 30 C occurred after 61 {+-} 7 minutes in Slurry group 2 vs. 24 {+-} 6 minutes in Saline group 2 (P < .0001). Core temperature decreased on average to 35 C in the Saline groups compared with 37 C in the Slurry groups (P < .0001). Serum creatinine did not differ between the Saline and Slurry groups in Phases I and II at any time point. Ice slurry provides superior renal cooling compared with near-frozen saline during LPN without associated core hypothermia.

  2. Distribution of phosphorus in manure slurry and its infiltration after application to soils.

    PubMed

    Vadas, Peter A

    2006-01-01

    Computer models help identify agricultural areas where P transport potential is high, but commonly used models do not simulate surface application of manures and P transport from manures to runoff. As part of an effort to model such P transport, we conducted manure slurry separation and soil infiltration experiments to determine how much slurry P infiltrates into soil after application but before rain, thus becoming less available to runoff. We applied dairy and swine slurry to soil columns and after both 24 and 96 h analyzed solids remaining on the soil surface for dry matter, total phosphorus (TP), and water-extractable inorganic (WEIP) and organic (WEOP) phosphorus. We analyzed underlying soils for Mehlich-3 and water-extractable P. We also conducted slurry separation experiments by sieving, centrifuging, and suction-filtering to determine which method could easily estimate slurry P infiltration into soils. About 20% of slurry solids and 40 to 65% of slurry TP and WEIP infiltrated into soil after application, rendering this P less available to transport in runoff. Slurry separation by suction-filtering through a screen with 0.75-mm-diameter openings was the best method to estimate this slurry P infiltration. Measured quantities of manure WEOP changed too much during experiments to estimate WEOP infiltration into soil or what separation method can approximate infiltration. Applying slurries to soils always increased soil P in the top 0 to 1 cm of soil, frequently in the 1- to 2-cm depth of soil, but rarely below 2 cm. Future research should use soils with coarser texture or large macropores, and slurry with low dry matter content (1-2%).

  3. An investigation on the rheological behavior of metallic semi-solid slurries of Al-6.5 pct Si and semi-solid composite slurries of SiC particulates in an Al-6.5 pct Si alloy matrix

    NASA Technical Reports Server (NTRS)

    Moon, H.-K.; Ito, Y.; Cornie, J. A.; Flemings, M. C.

    1993-01-01

    The rheology of SiC particulate/Al-6.5 pct Si composite slurries was explored. The rheological behavior of the composite slurries shows both thixotropic and pseudoplastic behaviors. Isostructural experiments on the composite slurries revealed a Newtonian behavior beyond a high shear rate limit. The rheology of fully molten composite slurries over the low to high shear rate range indicates the existence of a low shear rate Newtonian region, an intermediate pseudoplastic region and a high shear rate Newtonian region. The isostructural studies indicate that the viscosity of a composite slurry depends upon the shearing history of a given volume of material. An unexpected shear thinning was noted for SiC particulate + alpha slurries as compared to semi-solid metallic slurries at the same fraction solid. The implications of these findings for the processing of slurries into cast components is discussed.

  4. Influence of soil structure on contaminant leaching from injected slurry.

    PubMed

    Amin, M G Mostofa; Pedersen, Christina Østerballe; Forslund, Anita; Veith, Tamie L; Laegdsmand, Mette

    2016-12-15

    Animal manure application to agricultural land provides beneficial organic matter and nutrients but can spread harmful contaminants to the environment. Contamination of fresh produce, surface water and shallow groundwater with the manure-borne pollutants can be a critical concern. Leaching and persistence of nitrogen, microorganisms (bacteriophage, E. coli, and Enterococcus) and a group of steroid hormone (estrogens) were investigated after injection of swine slurry into either intact (structured) or disturbed (homogeneous repacked) soil. The slurry was injected into hexaplicate soil columns at a rate of 50 t ha(-1) and followed with four irrigation events: 3.5-h period at 10 mm h(-1) after 1, 2, 3, and 4 weeks. The disturbed columns delayed the leaching of a conservative tracer and microorganisms in the first irrigation event compared to the intact columns due to the effect of disturbed macropore flow paths. The slurry constituents that ended up in or near the macropore flow paths of the intact soil were presumably washed out relatively quickly in the first event. For the last three events the intact soil leached fewer microorganisms than the disturbed soil due to the bypassing effect of water through the macropore flow path in the intact soil. Estrogen leached from the intact soil in the first event only, but for the disturbed soil it was detected in the leachates of last two events also. Leaching from the later events was attributed to higher colloid transport from the disturbed soils. In contrast, NO3-N leaching from the intact soil was higher for all events except the first event, probably due to a lower nitrification rate in the disturbed soil. A week after the last irrigation event, the redistribution of all slurry constituents except NO3-N in most of the sections of the soil column was higher for the disturbed soil. Total recovery of E. coli was significantly higher from the disturbed soil and total leaching of mineral nitrogen was significantly lower

  5. Magnetic sorbents added to soil slurries lower Cr aqueous concentration

    NASA Astrophysics Data System (ADS)

    Aravantinos, Konstantinos; Isari, Ekavi; Karapanagioti, Hrissi K.; Manariotis, Ioannis D.; Werner, David

    2016-04-01

    Activated carbon (AC) acts as a strong binding agent that lowers the pollutant concentration and, thus its toxicity. Another promising sorbent material in environmental applications is biochar (BC) which is obtained from the incomplete combustion of carbon-rich biomass under oxygen-limited conditions. Both of these materials could be used as soil or sediment amendments that would lower the toxicity in the aqueous phase. A draw back of this technique is that although the pollutant will remain non- bioavailable for many years being sorbed into these sorbents, it actually stays into the system. The objective of this study was (a) to synthesize a magnetic powdered activated carbon (AC/Fe) and magnetic powdered biochar (BC/Fe) produced from a commercial AC sample and BC, respectively and (b) to evaluate the potential use of AC/Fe and BC/Fe to lower Cr concentration that desorb from two soils in their soil slurries. The two soil samples originate from the vicinity of a local metal shop. The BC was produced from olive pomace. The surface area, the pore volume, and the average pore size of each sorbent were determined using gas (N2) adsorption-desorption cycles and the Brunauer, Emmett, and Teller (BET) equation. Isotherms with 30 adsorption and 20 desorption points were conducted at liquid nitrogen temperature (77K). Open surface area and micropore volume were determined using t-plot method and Harkins & Jura equation. For both AC/Fe, surface area measurements resulted in 66% those of corresponding AC. For BC/Fe, the surface area was 82% that of BC. Our previous studies have shown that both AC/Fe and BC/Fe are effective sorbents for mercury in aqueous solutions but with lower sorption capacity compared to the initial materials (50-75% lower). Batch experiments with all sorbent samples and each soil were conducted at room temperature (25oC) in order to compare the sorption properties of the materials. The soil slurries demonstrated low Cr concentrations (10.9 and 14.6

  6. Slurry-based fabrication of chopped fiberglass composite preforms

    SciTech Connect

    Moore, G.A.; Johnson, R.W.; Landon, M.D.; Stoots, C.M.; Anderson, J.L.

    1995-12-01

    A water-based process for the fabrication of chopped fiberglass preforms is being developed in collaboration with the Automotive Composite Consortium (ACC) and The Budd Company. This slurry process uses hydraulic pressure to form highly compacted fiberglass preforms on contoured, perforated metal screens. The preforms will be used in the development of structural automotive composites. A key objective is to produce preforms having uniform areal density. Computational simulation of variable open area screens, and areal density mapping using a gamma densitometer are discussed.

  7. Field experiences with intelligent pigs

    SciTech Connect

    Smith, S.N.; Duvivier, J.P.; Lefevre, D.E.; Robb, G.A.

    1996-08-01

    Oil and gas production operations use intelligent pigs for corrosion inspection of gathering systems and pipelines worldwide. The authors have been involved with intelligent pig inspections which have been conducted on over 155 different pipelines owned by one international corporation. A variety of intelligent pig vendors have been used with tools ranging from standard first generation magnetic flux leakage (MFL) to high-resolution MFL to standard and custom made ultrasonic (UT) tools. Experiences encountered during these inspections are discussed and resolutions to many of the problems are described.

  8. Investigation of the disposal of dead pigs by pig farmers in mainland China by simulation experiment.

    PubMed

    Wu, Linhai; Xu, Guoyan; Li, Qingguang; Hou, Bo; Hu, Wuyang; Wang, Jianhua

    2017-01-01

    Dead pigs are a major waste by-product of pig farming. Thus, safe disposal of dead pigs is important to the protection of consumer health and the ecological environment by preventing marketing of slaughtered and processed dead pigs and improper dumping of dead pigs. In this study, a probability model was constructed for the disposal of dead pigs by pig farmers by selecting factors affecting disposal. To that end, we drew on the definition and meaning of behavior probability based on survey data collected from 654 pig farmers in Funing County, Jiangsu Province, China. Moreover, the role of influencing factors in pig farmers' behavioral choices regarding the disposal of dead pigs was simulated by simulation experiment. The results indicated that years of farming had a positive impact on pig farmers' choice of negative disposal of dead pigs. Moreover, there was not a simple linear relationship between scale of farming and pig farmers' behavioral choices related to the disposal of dead pigs. The probability for farmers to choose the safe disposal of dead pigs increased with the improvement of their knowledge of government policies and relevant laws and regulations. Pig farmers' behavioral choice about the disposal of dead pigs was also affected by government subsidy policies, regulation, and punishment. Government regulation and punishment were more effective than subsidy. The findings of our simulation experiment provide important decision-making support for the governance in preventing the marketing of dead pigs at the source.

  9. Fused slurry silicide coatings for columbium alloy reentry heat shields. Volume 2: Experimental and coating process details

    NASA Technical Reports Server (NTRS)

    Fitzgerald, B.

    1973-01-01

    The experimental and coating process details are presented. The process specifications which were developed for the formulation and application of the R-512E fused slurry silicide coating using either an acrylic or nitrocellulose base slurry system is also discussed.

  10. Narrow grass hedge effects on nutrient transport following swine slurry application

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The effectiveness of a narrow grass hedge in reducing runoff nutrient loads following swine slurry application was examined in this study. Slurry was applied to 0.75-m wide by 4.0-m long plots established on an Aksarben silty clay loam soil located in southeast Nebraska. Manure treatments consisted ...

  11. Effects of dairy slurry on silage fermentation characteristics and nutritive value of alfalfa

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Dairy producers frequently ask questions about the risks associated with applying dairy slurry to growing alfalfa (Medicago sativa L.). Our objectives were to determine the effects of applying dairy slurry on the subsequent nutritive value and fermentation characteristics of alfalfa balage. Dairy sl...

  12. High density ash slurry pumping and disposal: An environmentally safe and economical alternative

    SciTech Connect

    Broek, B. van den

    1999-07-01

    The paper describes conventional ash disposal systems; high density slurry transportation and disposal systems, including the design, disposal site, technical features, sloped disposal site operating parameters, slurry quality and deposit management; typical operational questions; specific advantages of the proposed GEHO system; and GEHO piston diaphragm pumps.

  13. 30 CFR 77.216-5 - Water, sediment or slurry impoundments and impounding structures; abandonment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Water, sediment or slurry impoundments and... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216-5 Water, sediment or..., sediment, or slurry impoundment and impounding structure which meets the requirements of 30 CFR...

  14. 30 CFR 77.216-4 - Water, sediment or slurry impoundments and impounding structures; reporting requirements...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Water, sediment or slurry impoundments and....216-4 Water, sediment or slurry impoundments and impounding structures; reporting requirements... of the initial plan approval, the person owning, operating, or controlling a water, sediment,...

  15. 30 CFR 77.216-3 - Water, sediment, or slurry impoundments and impounding structures; inspection requirements...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-3 Water, sediment, or slurry impoundments and impounding structures; inspection requirements; correction of hazards; program requirements. (a) All water, sediment,...

  16. 30 CFR 77.216-3 - Water, sediment, or slurry impoundments and impounding structures; inspection requirements...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-3 Water, sediment, or slurry impoundments and impounding structures; inspection requirements; correction of hazards; program requirements. (a) All water, sediment,...

  17. 30 CFR 77.216-5 - Water, sediment or slurry impoundments and impounding structures; abandonment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Water, sediment or slurry impoundments and... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216-5 Water, sediment or..., sediment, or slurry impoundment and impounding structure which meets the requirements of 30 CFR...

  18. 30 CFR 77.216-3 - Water, sediment, or slurry impoundments and impounding structures; inspection requirements...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-3 Water, sediment, or slurry impoundments and impounding structures; inspection requirements; correction of hazards; program requirements. (a) All water, sediment,...

  19. 30 CFR 77.216-5 - Water, sediment or slurry impoundments and impounding structures; abandonment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Water, sediment or slurry impoundments and... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216-5 Water, sediment or..., sediment, or slurry impoundment and impounding structure which meets the requirements of 30 CFR...

  20. 30 CFR 77.216-4 - Water, sediment or slurry impoundments and impounding structures; reporting requirements...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Water, sediment or slurry impoundments and....216-4 Water, sediment or slurry impoundments and impounding structures; reporting requirements... of the initial plan approval, the person owning, operating, or controlling a water, sediment,...

  1. 30 CFR 77.216-3 - Water, sediment, or slurry impoundments and impounding structures; inspection requirements...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-3 Water, sediment, or slurry impoundments and impounding structures; inspection requirements; correction of hazards; program requirements. (a) All water, sediment,...

  2. 30 CFR 77.216-5 - Water, sediment or slurry impoundments and impounding structures; abandonment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Water, sediment or slurry impoundments and... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216-5 Water, sediment or..., sediment, or slurry impoundment and impounding structure which meets the requirements of 30 CFR...

  3. 30 CFR 77.216-3 - Water, sediment, or slurry impoundments and impounding structures; inspection requirements...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-3 Water, sediment, or slurry impoundments and impounding structures; inspection requirements; correction of hazards; program requirements. (a) All water, sediment,...

  4. 30 CFR 77.216-5 - Water, sediment or slurry impoundments and impounding structures; abandonment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Water, sediment or slurry impoundments and... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.216-5 Water, sediment or..., sediment, or slurry impoundment and impounding structure which meets the requirements of 30 CFR...

  5. 30 CFR 77.216-4 - Water, sediment or slurry impoundments and impounding structures; reporting requirements...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Water, sediment or slurry impoundments and....216-4 Water, sediment or slurry impoundments and impounding structures; reporting requirements... of the initial plan approval, the person owning, operating, or controlling a water, sediment,...

  6. 30 CFR 77.216-4 - Water, sediment or slurry impoundments and impounding structures; reporting requirements...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Water, sediment or slurry impoundments and....216-4 Water, sediment or slurry impoundments and impounding structures; reporting requirements... of the initial plan approval, the person owning, operating, or controlling a water, sediment,...

  7. 30 CFR 77.216-4 - Water, sediment or slurry impoundments and impounding structures; reporting requirements...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Water, sediment or slurry impoundments and....216-4 Water, sediment or slurry impoundments and impounding structures; reporting requirements... of the initial plan approval, the person owning, operating, or controlling a water, sediment,...

  8. Method of preparing a high solids content, low viscosity ceramic slurry

    DOEpatents

    Tiegs, Terry N.; Wittmer, Dale E.

    1995-01-01

    A method for producing a high solids content, low viscosity ceramic slurry composition comprises turbomilling a dispersion of a ceramic powder in a liquid to form a slurry having a viscosity less than 100 centipoise and a solids content equal to or greater than 48 volume percent.

  9. Method of preparing a high solids content, low viscosity ceramic slurry

    DOEpatents

    Tiegs, T.N.; Wittmer, D.E.

    1995-10-10

    A method for producing a high solids content, low viscosity ceramic slurry composition comprises turbomilling a dispersion of a ceramic powder in a liquid to form a slurry having a viscosity less than 100 centipoise and a solids content equal to or greater than 48 volume percent.

  10. Addition of pectin and soy soluble polysaccharide affects the particle size distribution of casein suspensions prepared from acidified skim milk.

    PubMed

    Liu, JinRu; Nakamura, Akihiro; Corredig, Milena

    2006-08-23

    Pectins are negatively charged polysaccharides employed as stabilizers in acidified milk dispersions, where caseins aggregate because of the low pH and serum separation needs to be prevented. The objective of this research was to study the effect of charge on the stabilizing functionality of the polysaccharide in acid milk drinks. Unstandardized pectins with various charges (as degree of esterification, DE) as well as soybean soluble polysaccharide (SSPS) were tested for their stabilizing behavior as a function of pH and concentration. Skim milk was acidified by glucono-delta-lactone and then homogenized in the presence of polysaccharide at different pH values (in the range from 4.2 to 3.0). Measurements of particle size distribution demonstrated that pectins with a DE of 71.4, 68.6, and 67.4 stabilized milk at pH > 4.0. Pectins with a lower DE (63.9%) needed a higher concentration (0.4%) at the same pH to show a monomodal distribution of particle sizes. Pectins with lower DE (<50%) did not stabilize the dispersions. Although this difference in behavior was attributed mainly to the pectin charge, the efficiency in stabilizing the casein dispersion decreased with decreasing pectin size. For example, the high methoxyl pectin (HMP) with 63.9 DE was smaller in size than the HMPs with a higher charge. Pectins showed a pH-dependent stabilization effect, as at pH < 4.0 the dispersions contained aggregates. When SSPS was used to stabilize acid milk, at pH < 4.0, it showed a better stabilization behavior than HMP. When SSPS and pectin were used in combination, the particle size distribution of the acid milk dispersion was pH-dependent, and results were similar to those for samples containing pectin alone. This suggested that in the mixture, pectin dominated the behavior over SSPS, even when an excess of SSPS was added to the dispersions before homogenization.

  11. Metals attenuation in minerally-enhanced slurry walls

    SciTech Connect

    Evans, J.C.; Prince, M.J.; Adams, T.L.

    1997-12-31

    In current practice, a soil-bentonite slurry trench cutoff wall is a mixture of water, soil, and bentonite that is designed to serve as a passive barrier to ground water and contaminant transport. This study evaluated the transformation of a passive slurry trench cutoff wall barrier to an active barrier system. Conventional soil-bentonite vertical barriers presently serve as passive barriers to contaminated ground water. An active barrier will not only fulfill the functions of the present passive barrier system, but also retard contaminant transport by adsorptive processes. Attapulgite, Na-chabazite, and Ca-chabazite were added to {open_quotes}activate{close_quotes} the conventional soil-bentonite backfill. Batch extraction tests were performed to determine the partitioning coefficients of cadmium and zinc between the liquid and solid phase when in contact with the backfill mixes. Batch extraction and mathematical modeling results demonstrate the ability of an active barrier to retard the transport of cadmium and zinc. The reactivity of the soil-bentonite vertical barrier depends heavily on the inorganic being adsorbed. The reactivity of the barrier also depends on the adsorptive capabilities of the clay minerals added to the conventional soil-bentonite vertical barrier. The results of laboratory studies suggest that passive barrier systems can be transformed to active systems. Further, the data suggests that although conventional soil-bentonite vertical barriers are presently designed as passive barriers, they already have adsorptive capacity associated with active barriers.

  12. A novel method of atomizing coal-water slurry fuels

    SciTech Connect

    Sojka, P.E.; Lefebvre, A.H.

    1990-05-01

    Despite the body of work describing the performance of effervescent atomizers, its potential for use with coal water slurries (CWS) had not been evaluated prior to this study. This program was therefore undertaken: to demonstrate that effervescent atomization can produce CWS sprays with mean drop sizes below 50{mu}m; to determine a lower size limit for effervescent atomizer produced CWS sprays; to determine the mechanism(s) responsible for the formation of effervescent atomizer produced sprays. An analysis of the effects of slurry rheological properties (as indicated by the consistency index and the flow behavior index) and formulation (in terms of loading and coal particle top size) on the spray formation process was performed. The experimental data reported were then analyzed to explain the physical processes responsible for spray formation. The analysis began by considering an energy balance across a control volume that extended from the nozzle exit plant to the line of spray measurement. The inlet conditions were calculated using two-phase flow techniques and the outlet conditions were calculated by using conservation of momentum and assuming that the final velocities of the air and liquid were equal. Entrainment was considered negligible and losses were accounted for by realizing that only a small fraction of the atomizing air participated in the spray formation process with the remainder passing through the control volume unperturbed. Results are discussed. 41 figs., 4 tabs.

  13. The granular mixing in a slurry rotating drum

    NASA Astrophysics Data System (ADS)

    Liao, C. C.; Hsiau, S. S.

    2010-03-01

    The mixing dynamics of granular materials immersed in a liquid was experimentally studied in a quasi-2D rotating drum. A DV (SONY DCR-TRV900 NTSC) motion corder analyzer was used to record the motions of granular materials. The effects of interstitial fluid viscosity and filling degree on the mixing index, mixing rate constant, and dynamic repose angle in the rotating drum were investigated and discussed in this paper. The experimental results show that the interstitial fluid viscosity has almost not influence on the final stable mixing index but has significantly effects on the mixing rate constant and dynamic repose angle in slurry granular flows. The results show that the mixing rate and dynamic repose angle increase with increasing the interstitial fluid viscosity. The results also indicate that the filling degree plays an important role in mixing dynamics in slurry granular flows. The mixing rate constant is demonstrated to be decreased with increasing the filling degree. The dynamic repose angle is not altered by the filling degree. Finally, we find that the dynamic repose angle and the mixing rate constant increase slightly at high Stokes number and increase dramatically at low Stokes number with decreasing Stokes number.

  14. Separation of catalyst from Fischer-Tropsch slurry

    DOEpatents

    White, Curt M.; Quiring, Michael S.; Jensen, Karen L.; Hickey, Richard F.; Gillham, Larry D.

    1998-10-27

    In a catalytic process for converting synthesis gas including hydrogen and carbon monoxide to hydrocarbons and oxygenates by a slurry Fischer-Tropsch synthesis, the wax product along with dispersed catalyst is removed from the slurry and purified by removing substantially all of the catalyst prior to upgrading the wax and returning a portion to the Fischer-Tropsch reaction. Separation of the catalyst particles from the wax product is accomplished by dense gas and/or liquid extraction in which the organic compounds in the wax are dissolved and carried away from the insoluble inorganic catalyst particles that are primarily inorganic in nature. The purified catalyst free wax product can be subsequently upgraded by various methods such as hydrogenation, isomerization, hydrocracking, conversion to gasoline and other products over ZSM-5 aluminosilicate zeolite, etc. The catalyst particles are returned to the Fischer-Tropsch Reactor by slurring them with a wax fraction of appropriate molecular weight, boiling point and viscosity to avoid reactor gelation.

  15. Separation of catalyst from Fischer-Tropsch slurry

    DOEpatents

    White, C.M.; Quiring, M.S.; Jensen, K.L.; Hickey, R.F.; Gillham, L.D.

    1998-10-27

    In a catalytic process for converting synthesis gas including hydrogen and carbon monoxide to hydrocarbons and oxygenates by a slurry Fischer-Tropsch synthesis, the wax product along with dispersed catalyst is removed from the slurry and purified by removing substantially all of the catalyst prior to upgrading the wax and returning a portion to the Fischer-Tropsch reaction. Separation of the catalyst particles from the wax product is accomplished by dense gas and/or liquid extraction in which the organic compounds in the wax are dissolved and carried away from the insoluble inorganic catalyst particles that are primarily inorganic in nature. The purified catalyst-free wax product can be subsequently upgraded by various methods such as hydrogenation, isomerization, hydrocracking, conversion to gasoline and other products over ZSM-5 aluminosilicate zeolite, etc. The catalyst particles are returned to the Fischer-Tropsch Reactor by mixing them with a wax fraction of appropriate molecular weight, boiling point and viscosity to avoid reactor gelation. 2 figs.

  16. KINETICS OF SLURRY PHASE FISCHER-TROPSCH SYNTHESIS

    SciTech Connect

    Dragomir B. Bukur; Gilbert F. Froment; Lech Nowicki; Jiang Wang; Wen-Ping Ma

    2003-09-29

    This report covers the first year of this three-year research grant under the University Coal Research program. The overall objective of this project is to develop a comprehensive kinetic model for slurry phase Fischer-Tropsch synthesis on iron catalysts. This model will be validated with experimental data obtained in a stirred tank slurry reactor (STSR) over a wide range of process conditions. The model will be able to predict concentrations of all reactants and major product species (H{sup 2}O, CO{sub 2}, linear 1- and 2-olefins, and linear paraffins) as a function of reaction conditions in the STSR. During the reporting period we have completed one STSR test with precipitated iron catalyst obtained from Ruhrchemie AG (Oberhausen-Holten, Germany). This catalyst was initially in commercial fixed bed reactors at Sasol in South Africa. The catalyst was tested at 13 different sets of process conditions, and had experienced a moderate deactivation during the first 500 h of testing (decrease in conversion from 56% to 50% at baseline process conditions). The second STSR test has been initiated and after 270 h on stream, the catalyst was tested at 6 different sets of process conditions.

  17. Dimethyl ether synthesis from syngas in slurry phase

    SciTech Connect

    Han, Y.Z.; Fujimoto, K.; Shikata, T.

    1997-12-31

    Dimethyl ether (DME) is one of the important chemicals derived from synthesis gas. It can be widely used in syngas conversion, production of olefins, or MTG gasoline. Recently, is has been noticed as a substitute of LPG used as home fuel. In the present study, dimethyl ether was effectively synthesized from CO rich syngas (H{sub 2}/CO=1/1) over hybrid catalyst containing a Cu-Zn-Al(O) based methanol synthesis catalyst and {gamma}-alumina in an agitated slurry reactor under relatively mild reaction conditions: temperature 230--300 C, pressure 2.0--5.0 MPa, contact time 2.0--10 gram-cat.-h/mol. The catalysts used as the methanol active components were commercially available Cu-Zn-Al(O) based catalysts, BASF S385 and ICI 51-2. Two kinds of {gamma}-alumina ALO4 (standard catalyst of the Catalysis Society of Japan) and N612N (NIKKI Co., Japan) were used as the methanol dehydration components. The slurry was prepared by mixing the fine powder (<100 mesh) of catalyst components with purified n-hexadecane. The catalysts were reduced by a mixing gas containing 20% syngas and 80% nitrogen with a three-hour programmed temperature raising from room temperature to the final temperature. All products were analyzed by gas chromatographs. Results are given and discussed.

  18. KINETICS OF SLURRY PHASE FISCHER-TROPSCH SYNTHESIS

    SciTech Connect

    Dragomir B. Bukur

    2004-09-29

    This report covers the second year of this three-year research grant under the University Coal Research program. The overall objective of this project is to develop a comprehensive kinetic model for slurry phase Fischer-Tropsch synthesis on iron catalysts. This model will be validated with experimental data obtained in a stirred tank slurry reactor (STSR) over a wide range of process conditions. The model will be able to predict concentrations of all reactants and major product species (H{sub 2}O, CO{sub 2}, linear 1- and 2-olefins, and linear paraffins) as a function of reaction conditions in the STSR. During the second year of the project we completed the STSR test SB-26203 (275-343 h on stream), which was initiated during the first year of the project, and another STSR test (SB-28603 lasting 341 h). Since the inception of the project we completed 3 STSR tests, and evaluated catalyst under 25 different sets of process conditions. A precipitated iron catalyst obtained from Ruhrchemie AG (Oberhausen-Holten, Germany) was used in all tests. This catalyst was used initially in commercial fixed bed reactors at Sasol in South Africa. Also, during the second year we performed a qualitative analysis of experimental data from all three STSR tests. Effects of process conditions (reaction temperature, pressure, feed composition and gas space velocity) on water-gas-shift (WGS) activity and hydrocarbon product distribution have been determined.

  19. PCR-DGGE analysis of the bacterial composition of a kaolin slurry showing altered rheology.

    PubMed

    Papp, Ildikó; Balázs, Margit; Tombácz, Etelka; Babcsán, Norbert; Kesserű, Péter; Kiss, István; Szvetnik, Attila

    2012-04-01

    Kaolin is an important industrial raw material and a basis of a range of different products. Microbial spoilage is a detrimental process observed especially in kaolin slurries, leading to low quality products and economic loss. Although the alteration of kaolin slurries in ceramic industry was observed, the process and the microbial background have not been analyzed in details. This study provides the first data using a cultivation independent molecular biological approach (PCR-DGGE) regarding the bacterial composition of an altered kaolin slurry. The results show that potential exopolymer (EPS) producer bacteria (e.g. Acinetobacter, Pseudomonas) appear in the altered kaolin slurry, which may have an important role in the modification of kaolin slurries.

  20. Ultrasound stimulus effect on hydrogen bonding in networked alumina and polyacrylic acid slurry.

    PubMed

    Ngoc, Ngo Le; Takaomi, Kobayashi

    2010-01-01

    The influence of ultrasound (US) on the viscosity of aqueous slurry composing polyacrylic acid (PAA) and alumina was studied. For exposure to an aqueous slurry solution, US waves emitted at three different frequencies of 28, 45, and 100 kHz were used. Results show that the stimulus effect of US on viscosity change was a breakage of the hydrogen bonding networks of alumina and PAA in the slurry solution. That decrease in viscosity was enhanced strongly by US exposure as the output power was increased from 175 to 300 W. In addition, a lower US frequency was effective for slurry viscosity reduction. The reduced viscosity of the slurry also depended on the solution pH. After US was stopped, the viscosity increased gradually and recovered to its original value within about 15 min. The stimulus effect on the viscosity change was cycled by US.

  1. Study of the physical properties of petrolatum-stabilized magnesium-hydrocarbon slurry fuels

    NASA Technical Reports Server (NTRS)

    Pinns, Murray L; Goodman, Irving A

    1954-01-01

    Magnesium-hydrocarbon slurries containing a moderate proportion of petrolatum have physical properties such that they offer promise as experimental aircraft fuels. The settling of the magnesium is greatly retarded by the petrolatum, and the slurries can easily be remixed to their original condition after storage. Successive batches which have closely similar properties can be prepared readily. The apparent viscosity of these slurries increased rapidly with increasing magnesium concentration, with increasing petrolatum concentration, and with decreasing temperature. As the apparent viscosity increased, the extent of settling and the ease of remixing both decreased. Although no quantitative correlation was found between the properties of the slurry and those of the petrolatum, and no one petrolatum gave slurries which were best in all respects, one of the five petrolatum used was judged to be superior to the others.

  2. Design and Operation of Large Size Circulating Fluidized Bed Boiler Fired Slurry and Gangue

    NASA Astrophysics Data System (ADS)

    Man, Zhang; Rushan, Bie; Fengjun, Wang

    The way which burns slurry and gangue to generate electricity and provide heat has been always desired. If mixture of slurry and gangue are burnt by conventional combustion technology, it is difficult to be satisfied., but for circulating fluidized bed(CFB) boiler, it is flexible for fuels and it is easy to desulfurize and DeNox in the furnace of the boiler. There are lots of advantages to burning the mixture of slurry and gangue in CFB boiler. This technology has been researched and practiced for many years, it is mature now and has been used widely, by now, 50MW, 135MW and 300MW CFB boiler which burn the mixture of slurry and gangue have already been operated in China. In the paper, slurry characteristic and conveying is described, the design and operation of boilers mentioned above will be also introduced in detail.

  3. Compound cycle turbofan engine (CCTE). Task IX. Carbon-slurry fuel combustion evaluation program. Final report June-September 1979

    SciTech Connect

    Bruce, T.W.; Mongia, H.

    1980-03-01

    The carbon-slurry fuel evaluation program demonstrated the feasibility of running a currently available carbon-slurry fuel in a combustion rig and a turbine engine. This program also established the preliminary design criteria for operating on carbon-slurry fuels. Subcontracts work was performed by Pennsylvania State for fuel droplet measurements and by Suntech, Inc. for fuel development and manufacture.

  4. 30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-2 Water, sediment, or slurry impoundments and impounding... under design storm conditions, sediment or slurry level, water level and other information pertinent...

  5. 30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-2 Water, sediment, or slurry impoundments and impounding... under design storm conditions, sediment or slurry level, water level and other information pertinent...

  6. 30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-2 Water, sediment, or slurry impoundments and impounding... under design storm conditions, sediment or slurry level, water level and other information pertinent...

  7. 30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-2 Water, sediment, or slurry impoundments and impounding... under design storm conditions, sediment or slurry level, water level and other information pertinent...

  8. 30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Water, sediment, or slurry impoundments and... COAL MINES Surface Installations § 77.216-2 Water, sediment, or slurry impoundments and impounding... under design storm conditions, sediment or slurry level, water level and other information pertinent...

  9. Measurement of the Critical Deposition Velocity in Slurry Transport through a Horizontal Pipe

    SciTech Connect

    Erian, Fadel F.; Furfari, Daniel J.; Kellogg, Michael I.; Park, Walter R.

    2001-03-01

    Critical Deposition Velocity (CDV) is an important design and operational parameter in slurry transport. Almost all existing correlations that are used to predict this parameter have been obtained experimentally from slurry transport tests featuring single solid species in the slurry mixture. No correlations have been obtained to describe this parameter when the slurry mixture contains more than one solid species having a wide range of specific gravities, particle size distributions, and volume concentrations within the overall slurry mixture. There are no physical or empirical bases that can justify the extrapolation or modification of the existing single species correlations to include all these effects. New experiments must be carried out to obtain new correlations that would be suited for these types of slurries, and that would clarify the mechanics of solids deposition as a function of the properties of the various solid species. Our goal in this paper is to describe a robust experimental technique for the accurate determination of the critical deposition velocity associated with the transport of slurries in horizontal or slightly inclined pipes. Because of the relative difficulty encountered during the precise determination of this useful operational parameter, it has been the practice to connect it with some transitional behavior of more easily measurable flow parameters such as the pressure drop along the slurry pipeline. In doing so, the critical deposition velocity loses its unique and precise definition due to the multitude of factors that influence such transitional behaviors. Here, data has been obtained for single species slurries made up of washed garnet and water and flowing through a 1- inch clear pipe. The selected garnet had a narrow particle size distribution with a mean diameter of 100 mm, approximately. The critical deposition velocity was measured for garnet/water slurries of 10, 20, and 30 percent solids concentration by volume.

  10. Characterization of Flow Behavior of Semi-Solid Slurries with Low Solid Fractions

    NASA Astrophysics Data System (ADS)

    Chucheep, Thiensak; Wannasin, Jessada; Canyook, Rungsinee; Rattanochaikul, Tanate; Janudom, Somjai; Wisutmethangoon, Sirikul; Flemings, Merton C.

    2013-10-01

    Semi-solid slurry casting is a metal-forming process that involves transforming liquid metal into slurry having a low solid fraction and then forming the slurry into solid parts. To successfully apply this slurry-forming process, it is necessary to fully understand the flow behavior of semi-solid slurries. This present work applied the rapid quenching method and the modified gravity fluidity casting to investigate the flow behavior, which involves characterizations of the initial solid fraction, fluidity, and microstructure of semi-solid slurries. Three commercial aluminum alloys were used in this study: 383 (Al-Si11Cu), 356 (Al-Si7MgFe), and 7075 (Al-Zn6MgCu) alloys. The results show that the initial solid fractions can be controlled by varying the rheocasting time. The rapid quenching mold can be used to determine the initial solid fractions. In this method, it is important to apply the correcting procedure to account for growth during quenching and to include all the solid phases. Results from the fluidity study of semi-solid slurries show that the fluidity decreases as the initial solid fraction increases. The decrease is relatively rapid near the low end of the initial solid fraction curves, but is quite slow near the high end of the curves. All the three alloys follow this trend. The results also demonstrate that the slurries that contain high solid fractions of up to 30 pct can still flow well. The microstructure characterization results show that the solid particles in the slurries flow uniformly in the channel. A uniform and fine microstructure with limited phase segregation is observed in the slurry cast samples.

  11. Upwelling of Acidified Water: Not Just an Issue for Shellfish Hatcheries on the West Coast of the US

    NASA Astrophysics Data System (ADS)

    Poach, M.; Munroe, D.; Abrahamsen, I.

    2014-12-01

    Periodic upwelling events are known to occur off the coast of New Jersey during the summer. As with upwelling off the US West Coast, these events can transport acidified water to the surface and shoreward. To determine if upwelling events have the potential to impact shellfish hatcheries in New Jersey, a monitoring study was conducted at the Aquaculture Innovation Center (AIC) of Rutgers University. The AIC is an important hatchery supporting the New Jersey oyster aquaculture industry through the production of disease resistant seed oysters. Starting in June of 2014, temperature, salinity, dissolved oxygen and pH were continuously monitored at the AIC's intake pipe. Periodic grab samples were also collected at the intake and at locations within the facility. Grab samples were preserved and analyzed for pH and dissolved inorganic carbon (DIC). DIC and pH were used to calculate the aragonite saturation state of the sampled water. During an upwelling event in early July a drop in pH was measured at the intake. Grab samples showed that water of lower pH and aragonite saturation was entering the facility. These results show that hatcheries along the NJ coast need to be aware that upwelling events may bring conditions detrimental for shellfish production.

  12. ADM1-based modeling of methane production from acidified sweet sorghum extract in a two stage process.

    PubMed

    Antonopoulou, Georgia; Gavala, Hariklia N; Skiadas, Ioannis V; Lyberatos, Gerasimos

    2012-02-01

    The present study focused on the application of the Anaerobic Digestion Model 1 on the methane production from acidified sorghum extract generated from a hydrogen producing bioreactor in a two-stage anaerobic process. The kinetic parameters for hydrogen and volatile fatty acids consumption were estimated through fitting of the model equations to the data obtained from batch experiments. The simulation of the continuous reactor performance at all HRTs tested (20, 15, and 10d) was very satisfactory. Specifically, the largest deviation of the theoretical predictions against the experimental data was 12% for the methane production rate at the HRT of 20d while the deviation values for the 15 and 10d HRT were 1.9% and 1.1%, respectively. The model predictions regarding pH, methane percentage in the gas phase and COD removal were in very good agreement with the experimental data with a deviation less than 5% for all steady states. Therefore, the ADM1 is a valuable tool for process design in the case of a two-stage anaerobic process as well.

  13. Early postnatal diagnosis of hereditary spherocytosis by combining light microscopy, acidified glycerol lysis test and eosin-5'-maleimide binding assay.

    PubMed

    Andres, Oliver; Eber, Stefan; Speer, Christian P

    2015-12-01

    Exact diagnosis of hereditary spherocytosis (HS) is widely considered unreliable around birth. However, early postnatal diagnosis at the beginning of congenital hemolysis may be essential for managing neonatal anemia and hemolytic icterus, identifying those at high risk for severe hyperbilirubinemia, irreversible kernicterus, or sudden need for red cell transfusion. We analyzed 37 blood samples from neonates or infants up to six weeks of life that had been collected in-house or shipped to our laboratory due to suspected red cell membrane disorder. By combining assessment of red cell morphology, acidified glycerol lysis test (AGLT), and eosin-5'-maleimide (EMA) binding assay, we were able to clearly exclude HS in 22 and confirm HS in 10 patients, of which one had undergone red cell transfusion prior to blood sampling. Assessment of red cell morphology and normal test results allowed diagnosis of infantile pyknocytosis or Heinz body anemia in three neonates. Re-evaluation of five patients with inconsistent results of AGLT and EMA binding led to confirmation of HS in two cases. Automated analysis of hematologic parameters revealed elevated proportion of hyperdense cells to be a highly significant indicator for HS in neonatal infants. We showed that assessment of red cell morphology in combination with AGLT and EMA binding assay is a reliable basis for confirming or rejecting suspected diagnosis of HS even in neonates. Our data underline the necessity for blood sampling and laboratory exploration in suspected red cell membrane or enzyme defects at the earliest occasion.

  14. Effects of glycerol on enzymatic hydrolysis and ethanol production using sugarcane bagasse pretreated by acidified glycerol solution.

    PubMed

    Zhang, Zhanying; Wong, Heng H; Albertson, Peter L; Harrison, Mark D; Doherty, William O S; O'Hara, Ian M

    2015-09-01

    In this study, for the first time the effects of glycerol on enzymatic hydrolysis and ethanol fermentation were investigated. Enzymatic hydrolysis was inhibited slightly with 2.0 wt% glycerol, leading to reduction in glucan digestibility from 84.9% without glycerol to 82.9% (72 h). With 5.0 wt% and 10.0 wt% glycerol, glucan digestibility was reduced by 4.5% and 11.0%, respectively. However, glycerol did not irreversibly inhibit cellulase enzymes. Ethanol fermentation was not affected by glycerol up to 5.0 wt%, but was inhibited slightly at 10.0 wt% glycerol, resulting in reduction in ethanol yield from 86.0% in the absence of glycerol to 83.7% (20 h). Based on the results of laboratory and pilot-scale experiments, it was estimated that 0.142 kg ethanol can be produced from 1.0 kg dry bagasse (a glucan content of 38.0%) after pretreatment with acidified glycerol solution.

  15. Acidified pressurized hot water for the continuous extraction of cadmium and lead from plant materials prior to ETAAS

    NASA Astrophysics Data System (ADS)

    Morales-Muñoz, S.; Luque-García, J. L.; Luque de Castro, M. D.

    2003-01-01

    Acidified and pressurized hot water is proposed for the continuous leaching of Cd and Pb from plants prior to determination by electrothermal atomic absorption spectrometry. Beech leaves (a certified reference material—CRM 100—where the analytes were not certified) were used for optimizing the method by a multivariate approach. The samples (0.5 g) were subjected to dynamic extraction with water modified with 1% v/v HNO 3 at 250 °C as leachant. A kinetics study was performed in order to know the pattern of the extraction process. The method was validated with a CRM (olive leaves, 062 from the BCR) where the analytes had been certified. The agreement between the certified values and those found using the proposed method demonstrates its usefulness. The repeatability and within-laboratory reproducibility were 3.7 and 2.3% for Cd and 1.04% and 6.3% for Pb, respectively. The precision of the method, together with its efficiency, rapidity, and environmental acceptability, makes it a good alternative for the determination of trace metals in plant material.

  16. The effect of CO2 acidified sea water and reduced salinity on aspects of the embryonic development of the amphipod Echinogammarus marinus (Leach).

    PubMed

    Egilsdottir, Hronn; Spicer, John I; Rundle, Simon D

    2009-08-01

    We investigated the effect of CO(2) acidified sea water (S=35, 22 and 10(PSU)) on embryonic development of the intertidal amphipod Echinogammarus marinus (Leach). Low pH, but not low salinity (22(PSU)), resulted in a more protracted embryonic development in situ although the effect was only evident at low salinity. However reduced salinity, not pH, exerted a strong significant effect, on numbers and calcium content of hatchlings. Females exposed to low salinity (10(PSU)) did not carry eggs through to hatching. There was no significant difference in the number of viable hatchlings between females cultured in 22 and 35(PSU) but the exoskeleton of the juveniles at 22(PSU) contained significantly less calcium. Ocean acidification may affect aspects of E. marinus development but exposure to realistic low salinities appear, in the short term, to be more important in impacting development than exposure to CO(2) acidified sea water at levels predicted for 300 years time.

  17. Effects of acidified aqueous glycerol and glycerol carbonate pretreatment of rice husk on the enzymatic digestibility, structural characteristics, and bioethanol production.

    PubMed

    Ebrahimi, Majid; Villaflores, Oliver B; Ordono, Emma E; Caparanga, Alvin R

    2017-03-01

    Rice husk as an abundant biomass was used in this study, and it contained 30.1% glucan and 13.5% xylan, 22.4% lignin. The pretreated rice husk with glycerol carbonate and acidified aqueous glycerol (10% water) at 90°C and 130°C for 60min had the maximum yield of glucan digestibility which was 78.2% and 69.7% respectively, using cellulase for 72h. The simultaneous saccharification and fermentation was conducted anaerobically at 37°C with Saccharomyces cerevisiae, 5% w/v glucan and 10FPU/g glucan of cellulase. 11.58 and 8.84g/L was the highest ethanol concentration after 3days of incubation form pretreated rice husk with glycerol carbonate and acidified aqueous glycerol respectively.

  18. The rheology of cryovolcanic slurries: Motivation and phenomenology of methanol-water slurries with implications for Titan

    NASA Astrophysics Data System (ADS)

    Zhong, Fang; Mitchell, Karl L.; Hays, Charles C.; Choukroun, Mathieu; Barmatz, Martin; Kargel, Jeffrey S.

    2009-08-01

    The Cassini spacecraft has revealed landforms on the surface of Titan suggested to be viscous cryovolcanic flows and possibly eruptive domes. In order to relate those surface features to the processes and chemistries that produced them, it is necessary to construct flow models, which rely on characterization of the rheological properties of the eruptants. This paper describes our initial exploratory attempts to understand the rheological characteristics of cryogenic slurries, using a 40% methanol-water mixture, as a precursor to more detailed experiments. We have devised a new automated cryogenic rotational viscometer system to more fully characterize cryovolcanic slurry rheologies. A series of measurements were performed, varying first temperature, and then strain rate, which revealed development of yield stress-like behaviors, shear-rate dependence, and thixotropic behavior, even at relatively low crystal fractions, not previously reported. At fixed shear rate our data are fit well by the Andrade equation, with the activation energy modified by a solid volume fraction. At fixed temperature, depending on shearing history, a Cross model could describe our data over a wide shear rate range. A Bingham plastic model appears to be a good constitutive model for the data measured at high shear rates when the shear was global. The yield stress like behavior implies that levee formation on cryolava flows is more likely than would be inferred from the previous studies, and may provide a partial explanation for features interpreted as steep-sided volcanic constructs on Titan.

  19. Improving profitability through slurry management: a look at the impact of slurry pH on various glass types

    NASA Astrophysics Data System (ADS)

    Hooper, Abigail R.; Boffa, Christopher C.; Sarkas, Harry W.; Cureton, Kevin

    2015-08-01

    When building an optical system, optical fabricators and designers meticulously choose the glass types for their application knowing that each one will have different chemical, thermal and mechanical properties. As the requirements for new optical systems have grown more demanding, the range of available glass types has vastly expanded and the specifications on the produced products have grown tighter. In an attempt to simplify processes and streamline consumable purchases, optical polishing houses often rely on one polishing slurry to manage these vast array of glass types. An unforeseen consequence of these practices can be a reduction in productivity by reduced removal rate, poor yields and frequent rework all translating into higher costs and reduced profitability. In this paper, the authors will examine the impact slurry pH has on glass types of different compositions and chemical, thermal and mechanical properties when using a double-sided polishing process. Experiments will use material removal rate, surface quality, and surface figure to provide insight into improving process control for differing glass types. Further guidance will be provided on how simple on-site monitoring and adjustment can deliver improved profitability on challenging substrates.

  20. Influence of acid tolerance responses on survival, growth, and thermal cross-protection of Escherichia coli O157:H7 in acidified media and fruit juices.

    PubMed

    Ryu, J H; Beuchat, L R

    1998-12-22

    A study was done to determine survival and growth characteristics of acid-adapted, acid-shocked, and control cells of Escherichia coli O157:H7 inoculated into tryptic soy broth (TSB) acidified with organic acids and three commercial brands of apple cider and orange juice. The three types of cells behaved similarly in TSB acidified with acetic acid; however, in TSB (pH 3.9) acidified with lactic acid, acid-adapted cells were more tolerant than acid-shocked cells which, in turn, were more tolerant than control cells. The ability of the three types of cells to grow after inoculation into acidified TSB, then plated on tryptic soy agar containing sodium chloride was determined. Tolerance of acid-adapted cells and, less markedly, acid-shocked cells to sodium chloride was diminished, compared to control cells. The pathogen showed extraordinary tolerance to the low pH of apple cider and orange juice held at 5 or 25 degrees C for up to 42 days. Growth occurred in one brand of apple cider (pH 3.98) incubated at 25 degrees C. Regardless of test parameters, there was no indication that cell types differed in tolerance to the acidic environment in apple cider or orange juice. Survival of control, acid-adapted, and acid-shocked cells heated in apple cider and orange juice was studied. Within each apple cider or orange juice, D(52 degrees C)-values of acid-adapted cells were considerably higher than those of acid-shocked or control cells, which indicates that heat tolerance can be substantially enhanced by acid adaptation compared to acid shock.

  1. Slurry Phase Iron Catalysts for Indirect Coal LIquefaction.

    SciTech Connect

    Datye, A.K.

    1997-08-08

    This report covers the fourth six month period of this three year grant under the University Coal Research program. During this period, we have begun the synthesis of precipitated catalysts using a bench-top spray dryer. The influence of binders on particle strength was also studied using the ultrasonic fragmentation approach to derive particle breaking stress. A similar approach was used to derive particle strength of catalysts obtained from Mr. Robert Gormley at FETC. Over the next six month period, this work will be continued while the catalysts prepared here will be examined by TPR to determine reducibility and the extent of adverse iron-silica interactions. A fundamental study of Fe/silica interactions has been performed using temperature programmed reaction and TEM to provide understanding of how the silica binders influence the activity of Fe catalysts. To understand differences in the reducibility of the iron phase caused by silica, we have set up a temperature programmed reduction facility. TPR in H, as well as in CO was performed of Fe/ SiO, catalysts prepared by impregnation as well as by precipitation. What is unique about these studies is that high resolution TEM was performed on samples removed from the reactor at various stages of reduction. This helps provide direct evidence for the phase changes that are detected by TPR. We have continued the analysis of catalysts received from slurry reactor runs at Texas A&M university (TAMU) and the University of Kentucky Center for Applied Energy Research (CAER) by x-ray diffraction. The purpose of the XRD analysis was to determine the phase composition of catalysts derived from a slurry reaction run using Fe Fischer-Tropsch catalysts. We had previously described how catalyst removed in the hot wax may oxidize to magnetite if the wax is air-exposed. We have now received catalysts from CAER that were removed under a protective inert blanket, and we are in the process of analyzing them, but preliminary work

  2. Insulinoma in 2 guinea pigs (Cavia porcellus)

    PubMed Central

    2005-01-01

    Abstract This paper describes an insulinoma in 2 guinea pigs (Cavia porcellus). Both guinea pigs presented with neurologic signs and low blood glucose readings. The neurologic signs resolved with dextrose administration. Insulinoma was confirmed on postmortem examination. PMID:15943120

  3. Protozoan predation in soil slurries compromises determination of contaminant mineralization potential.

    PubMed

    Badawi, Nora; Johnsen, Anders R; Brandt, Kristian K; Sørensen, Jan; Aamand, Jens

    2012-11-01

    Soil suspensions (slurries) are commonly used to estimate the potential of soil microbial communities to mineralize organic contaminants. The preparation of soil slurries disrupts soil structure, however, potentially affecting both the bacterial populations and their protozoan predators. We studied the importance of this "slurry effect" on mineralization of the herbicide 2-methyl-4-chlorophenoxyacetic acid (MCPA, (14)C-labelled), focussing on the effects of protozoan predation. Mineralization of MCPA was studied in "intact" soil and soil slurries differing in soil:water ratio, both in the presence and absence of the protozoan activity inhibitor cycloheximide. Protozoan predation inhibited mineralization in dense slurry of subsoil (soil:water ratio 1:3), but only in the most dilute slurry of topsoil (soil:water ratio 1:100). Our results demonstrate that protozoan predation in soil slurries may compromise quantification of contaminant mineralization potential, especially when the initial density of degrader bacteria is low and their growth is controlled by predation during the incubation period.

  4. Experiments on densely-loaded non-Newtonian slurries in laminar and turbulent pipe flows

    NASA Astrophysics Data System (ADS)

    Park, J. T.; Mannheimer, R. J.; Grimley, T. A.; Morrow, T. B.

    1988-02-01

    An experimental description of the flow structure of non-Newtonian slurries in the laminar, transitional, and full turbulent pipe flow regimes is the primary objective of this research. Measurements include rheological characterization of the fluid and local fluid velocity measurements with a laser Doppler velocimeter (LDV). Optical access to the flow is gained through a test section and model slurry which are both transparent. The model slurry is formulated from silica gel particles and hydrocarbon liquid mixture whose indices of refraction are matched so that light is not scattered from the particles. Experiments are being conducted in a large-scale pipe slurry flow facility with an inside pipe diameter of 51 mm (2 inches). Detailed flow measurements including turbulence quantities such as Reynolds stress were measured with a two-component two-color LDV. The present research indicates that non-Newtonian slurries are possible with concentrations of a few percent by weight of small particles whose sizes are one micron or less. A non-Newtonian slurry from small particles could maintain large particles (100 micron size) at high concentrations in suspension almost indefinitely. Such a slurry would prevent particle fallout and its associated problems. Velocity profiles were acquired by the LDV in the laminar, transitional, and turbulent flow regimes. The velocity profile for laminar flow was in agreement with theory. The range of the transition region was 21 percent of the transition velocity in comparison to 50 percent for a Newtonian fluid.

  5. Experiments on densely-loaded non-Newtonian slurries in laminar and turbulent pipe flows

    NASA Astrophysics Data System (ADS)

    Park, J. T.; Mannheimer, R. J.; Grimley, T. A.; Morrow, T. B.

    1988-05-01

    An experimental description of the flow structure of non-Newtonian slurries in the laminar, transitional, and full turbulent pipe flow regimes is the primary objective of this research. Measurements include rheological characterization of the fluid and local fluid velocity measurements with a Laser Doppler Velocimeter (LDV). Optical access to the flow is gained through a test section and model slurry which are both transparent. The model slurry is formulated from silica gel particles and hydrocarbon liquid mixture whose indices of refraction are matched so that light is not scattered from the particles. Experiments are being conducted in a large-scale pipe slurry. Flow measurements including turbulence quantities such as Reynolds stress were measured with a two-component two-color LDV. The present research indicates that non-Newtonian slurries are possible with concentrations of a few percent by weight of small particles whose sizes are two microns or less. A non-Newtonian slurry from small particles could maintain large particles (one millimeter size) at high concentrations in suspension almost indefinitely. Such a slurry would prevent particle fallout and its associated problems.

  6. Experiments on densely-loaded non-Newtonian slurries in laminar and turbulent pipe flows

    NASA Astrophysics Data System (ADS)

    Park, J. T.; Mannheimer, R. J.; Grimley, T. A.; Morrow, T. B.

    1987-10-01

    An experimental description of the flow structure of non-Newtonian slurries in the laminar, transitional, and full turbulent pipe flow regimes is the primary objective of this research. Measurements include rheological characterization of the fluid and local fluid velocity measurements with a laser Doppler velocimeter (LDV). Optical access to the flow is gained through a test section and model slurry which are both transparent. The model slurry is formulated from silica gel particles and hydrocarbon liquid mixture whose indices of refraction are matched so that light is not scattered from the particles. Experiments are being conducted in a large-scale pipe slurry flow facility with an inside pipe diameter of 51 mm (2 inches). Detailed flow measurements including turbulence quantities such as Reynolds stress will be taken with a two-component two-color LDV. The present research indicates that non-Newtonian slurries are possible with concentrations of a few percent by weight of small particles whose sizes are one micron or less. A non-Newtonian slurry from small particles could maintain large particles (100 micron size) at high concentrations in suspension almost indefinitely. Such a slurry would prevent particle fallout and its associated problems.

  7. A Pipeline Transport Correlation for Slurries with Small but Dense Particles

    SciTech Connect

    Poloski, Adam P; Etchells, Arthur W; Chun, Jaehun; Adkins, Harold E; Casella, Andrew M; Minette, Michael J; Yokuda, Satoru T

    2010-04-01

    Most correlations/models for minimum transport or critical velocity of slurry were developed for slurries composed of particles greater than ~100-200 µm diameter with narrow particle-size distributions which is typical of the minerals industry. Many other process industries handle smaller particles. In particular waste slurries at the U.S. Department of Energy's Hanford Site have broad size distributions and significant fractions of smaller particles. Despite the size of these wastes, recent PNNL studies indicate that the small particles might be of sufficient density to pose a significant risk for pipeline deposition and plugging. To allow predictive assessment of deposition of fine dense particles for waste slurry transport at the U.S. DOE Hanford site, a pipeline-transport correlation for critical velocity was developed using a simple power-law between two dimensionless numbers important for slurry transport, the deposition Froude and Archimedes numbers. The correlation accords well with experimental data for slurries with Archimedes numbers <80 and is an adequate pipeline design guide for processing Hanford waste slurry.

  8. Fluid mechanics of slurry flow through the grinding media in ball mills

    SciTech Connect

    Songfack, P.K.; Rajamani, R.K.

    1995-12-31

    The slurry transport within the ball mill greatly influences the mill holdup, residence time, breakage rate, and hence the power draw and the particle size distribution of the mill product. However, residence-time distribution and holdup in industrial mills could not be predicted a priori. Indeed, it is impossible to determine the slurry loading in continuously operating mills by direct measurement, especially in industrial mills. In this paper, the slurry transport problem is solved using the principles of fluid mechanics. First, the motion of the ball charge and its expansion are predicted by a technique called discrete element method. Then the slurry flow through the porous ball charge is tackled with a fluid-flow technique called the marker and cell method. This may be the only numerical technique capable of tracking the slurry free surface as it fluctuates with the motion of the ball charge. The result is a prediction of the slurry profile in both the radial and axial directions. Hence, it leads to the detailed description of slurry mass and ball charge within the mill. The model predictions are verified with pilot-scale experimental work. This novel approach based on the physics of fluid flow is devoid of any empiricism. It is shown that the holdup of industrial mills at a given feed percent solids can be predicted successfully.

  9. Bio-polymer slurry trench method for installation of in-situ air sparging system

    SciTech Connect

    Linneman, D.M.

    1996-08-01

    An investigation was conducted at a site in Greenville Country, South Carolina which detected contaminants in the groundwater. It was then decided that remedial action was required. The contaminants and their location in the groundwater led to the selection of an in-situ air sparging system to be installed at approximately thirty-four feet deep. Due to design depth requirements and other site conditions, the bio-polymer slurry trench (B-P drain) Method was utilized in the air sparging system installation. The two trenches were installed using a biodegradable slurry in lieu of the bentonite slurry commonly utilized in the more traditional slurry trench technique. The slurry temporarily supported the trench walls while the air sparging components were submerged and set at the proper elevations Once backfilled with stone, the slurry in both trenches was broken by introducing a breaker solution which reduced the slurry to sugar water. The trenching, air sparging piping installation, and backfilling operations were completed in about six weeks.

  10. Impact of Rheological Modifiers on Various Slurries Supporting DOE Waste Processing

    SciTech Connect

    Chun, Jaehun; Bredt, Paul R.; Hansen, Erich; Bhosale, Prasad S.; Berg, John C.

    2010-03-11

    Controlling the stability and subsequent rheological properties of slurries has been an important but challenging issue in nuclear waste treatment, one that previous research has yet to sufficiently address. At the Hanford and Savannah River sites, operation of the waste treatment facilities at increased solids loading reduces the evaporative load on the melter systems and thereby increases waste processing rates. However, at these higher solids loadings, increased slurry rheology becomes a significant processing issue. The current study evaluates the use of several rheological modifiers to alleviate increased slurry rheology at high waste solids concentrations. Rheological modifiers change particle interactions in slurry. For colloidal slurries, modifiers mainly alter the electrostatic and steric interactions between particles, leading to a change in slurry rheology. Weak organic acid type rheological modifiers strengthen electrostatic repulsion whereas nonionic/polymer surfactant type rheological modifiers introduce a steric repulsion. We investigated various rheological modifiers using high level waste (HLW) nuclear waste simulants characterized typically by high ionic strength and a wide range of pH from 4 to 13. Using rheological analysis, it was found that citric acid and polyacrylic acid would be good rheological modifiers for the HLW simulants tested, effectively reducing slurry rheology by 40% or more. Physical insights into the mechanisms driving stabilization by these rheological modifiers will be discussed.

  11. Slurry sampling graphite furnace atomic absorption spectrometry: determination of trace metals in mineral coal.

    PubMed

    Silva, M M; Goreti, M; Vale, R; Caramão, E B

    1999-12-06

    A procedure for lead, cadmium and copper determination in coal samples based on slurry sampling using an atomic absorption spectrometer equipped with a transversely heated graphite tube atomizer is proposed. The slurries were prepared by weighing the samples directly into autosampler cups (5-30 mg) and adding a 1.5 ml aliquot of a diluent mixture of 5% v/v HNO(3), 0.05% Triton X-100 and 10% ethanol. The slurry was homogenized by manual stirring before measurement. Slurry homogenization using ultrasonic agitation was also investigated for comparison. The effect of particle size and the use of different diluent compositions on the slurry preparation were investigated. The temperature programmes were optimized on the basis of pyrolysis and atomization curves. Absorbance characteristics with and without the addition of a palladium-magnesium modifier were compared. The use of 0.05% m/v Pd and 0.03% m/v Mg was found satisfactory for stabilizing Cd and Pb. The calibration was performed with aqueous standards. In addition, a conventional acid digestion procedure was applied to verify the efficiency of the slurry sampling. Better recoveries of the analytes were obtained when the particle size was reduced to <37 mum. Several certified coal reference materials (BCR Nos. 40, 180, and 181) were analyzed, and good agreement was obtained between the results from the proposed slurry sampling method and the certificate values.

  12. Experimental aerosolized guinea pig-adapted Zaire ebolavirus (variant: Mayinga) causes lethal pneumonia in guinea pigs.

    PubMed

    Twenhafel, N A; Shaia, C I; Bunton, T E; Shamblin, J D; Wollen, S E; Pitt, L M; Sizemore, D R; Ogg, M M; Johnston, S C

    2015-01-01

    Eight guinea pigs were aerosolized with guinea pig-adapted Zaire ebolavirus (variant: Mayinga) and developed lethal interstitial pneumonia that was distinct from lesions described in guinea pigs challenged subcutaneously, nonhuman primates challenged by the aerosol route, and natural infection in humans. Guinea pigs succumbed with significant pathologic changes primarily restricted to the lungs. Intracytoplasmic inclusion bodies were observed in many alveolar macrophages. Perivasculitis was noted within the lungs. These changes are unlike those of documented subcutaneously challenged guinea pigs and aerosolized filoviral infections in nonhuman primates and human cases. Similar to findings in subcutaneously challenged guinea pigs, there were only mild lesions in the liver and spleen. To our knowledge, this is the first report of aerosol challenge of guinea pigs with guinea pig-adapted Zaire ebolavirus (variant: Mayinga). Before choosing this model for use in aerosolized ebolavirus studies, scientists and pathologists should be aware that aerosolized guinea pig-adapted Zaire ebolavirus (variant: Mayinga) causes lethal pneumonia in guinea pigs.

  13. Well completion and stimulation: good slurry blending enhances frac

    SciTech Connect

    Arribau, J.O.; Dorn, R.J.; Deleon, C.

    1982-02-01

    Successful fracturing is dependent in large part upon surface equipment. One critical factor is effective blending of the fracturing slurry before it is pumped into the formation. In hydraulic fracturing, a blender draws water from storage tanks to mix with sand, polymers, or other chemical additives. Solids and liquids generally are mixed by a paddle in a large open tub monitored visually for mixture level. The mixture then advances through the impeller zone of the blender. Conventional blending apparatus often requires multistage blending to mix large quantities of liquid and solids or additives and to maintain them in suspension when pumped the extended distances required in fracturing. Geo Condor, Inc. has developed a closed blending system, which provides a single-stage blending apparatus which achieves intimate mixing of liquid-solid or liquid-liquid constituents without altering the course or direction of liquid flow in established high-capacity mixing. The advantages and disadvantages of this system are discussed.

  14. Engineering development of slurry bubble column recactor(SBCR) technology

    SciTech Connect

    Bernard A. Toseland, Ph.D.

    1998-12-01

    The major technical objectives of this program are threefold: (1) to develop the design tools and a fundamental understanding of the fluid dynamics of a slurry bubble column reactor to maximize reactor productivity, (2) to develop the mathematical reactor design models and gain an understanding of the hydrodynamic fundamentals under industrially relevant process conditions, and (3) to develop an understanding of the hydrodynamics and their interaction with the chemistries occurring in the bubble column reactor. Successful completion of these objectives will permit more efficient usage of the reactor column and tighter design criteria, increase overall reactor efficiency, and ensure a design that leads to stable reactor behavior when scaling up to large diameter reactors.

  15. Thermodynamic assessment of microencapsulated sodium carbonate slurry for carbon capture

    SciTech Connect

    Stolaroff, Joshuah K.; Bourcier, William L.

    2014-01-01

    Micro-encapsulated Carbon Sorbents (MECS) are a new class of carbon capture materials consisting of a CO₂- absorbing liquid solvent contained within solid, CO₂-permeable, polymer shells. MECS enhance the rate of CO₂ absorption for solvents with slow kinetics and prevent solid precipitates from scaling and fouling equipment, two factors that have previously limited the use of sodium carbonate solution for carbon capture. Here, we examine the thermodynamics of sodium carbonate slurries for carbon capture. We model the vapour-liquid-solid equilibria of sodium carbonate and find several features that can contribute to an energy-efficient capture process: very high CO₂ pressures in stripping conditions, relatively low water vapour pressures in stripping conditions, and good swing capacity. The potential energy savings compared with an MEA system are discussed.

  16. Enhanced photocatalysis in a pilot laminar falling film slurry reactor

    SciTech Connect

    Puma, G.L.; Yue, P.L.

    1999-09-01

    Laminar falling film slurry (LFFS) photocatalytic reactors are one of the most efficient reactor configurations for conducting heterogeneous photocatalytic reactions, particularly for wastewater treatment. This paper presents a study on the oxidation of an aqueous salicylic acid waste in a pilot continuous flow LFFS photocatalytic reactor which has an optimum design for light absorption. In conducting the oxidation reaction, heterogeneous photocatalysis was supplemented with other photon-assisted processes. The effect of light intensity, radiation wavelength, oxidizing-enhancing agents, substrate and photocatalyst concentration, and exposure time were studied. A comparison of six different photon-based processes showed that higher oxidation rates of salicylic acid were obtained when there was concomitant photocatalysis, photolysis, and UV peroxidation. The oxidation rates of salicylic acid with this combined process were at least 1 order of magnitude higher in comparison with those for UVA photocatalysis and 3-fold higher in comparison with homogeneous UVC photolysis/UVC peroxidation.

  17. Drying and cracking mechanisms in a starch slurry.

    PubMed

    Goehring, Lucas

    2009-09-01

    Starch-water slurries are commonly used to study fracture dynamics. Drying starch cakes benefit from being simple, economical, and reproducible systems, and have been used to model desiccation fracture in soils, thin-film fracture in paint, and columnar joints in lava. In this paper, the physical properties of starch-water mixtures are studied, and used to interpret and develop a multiphase transport model of drying. Starch cakes are observed to have a nonlinear elastic modulus, and a desiccation strain that is comparable to that generated by their maximum achievable capillary pressure. It is shown that a large material porosity is divided between pore spaces between starch grains, and pores within starch grains. This division of pore space leads to two distinct drying regimes, controlled by liquid and vapor transport of water, respectively. The relatively unique ability for drying starch to generate columnar fracture patterns is shown to be linked to the unusually strong separation of these two transport mechanisms.

  18. ENGINEERING DEVELOPMENT OF SLURRY BUBBLE COLUMN REACTOR (SBCR) TECHNOLOGY

    SciTech Connect

    Bernard A. Toseland, Ph.D.

    1999-03-01

    The major technical objectives of this program are threefold: (1) to develop the design tools and a fundamental understanding of the fluid dynamics of a slurry bubble column reactor to maximize reactor productivity, (2) to develop the mathematical reactor design models and gain an understanding of the hydrodynamic fundamentals under industrially relevant process conditions, and (3) to develop an understanding of the hydrodynamics and their interaction with the chemistries occurring in the bubble column reactor. Successful completion of these objectives will permit more efficient usage of the reactor column and tighter design criteria, increase overall reactor efficiency, and ensure a design that leads to stable reactor behavior when scaling up to large diameter reactors. The past three months of research have been focused on two major areas of bubble column hydrodynamics: (1) pressure and temperature effects on gas holdup and (2) region transition using a sparger as a gas distributor.

  19. ENGINEERING DEVELOPMENT OF SLURRY BUBBLE COLUMN REACTOR (SBCR) TECHNOLOGY

    SciTech Connect

    Bernard A. Toseland, Ph.D.

    2002-01-01

    The major technical objectives of this program are threefold: (1) to develop the design tools and a fundamental understanding of the fluid dynamics of a slurry bubble column reactor to maximize reactor productivity, (2) to develop the mathematical reactor design models and gain an understanding of the hydrodynamic fundamentals under industrially relevant process conditions, and (3) to develop an understanding of the hydrodynamics and their interaction with the chemistries occurring in the bubble column reactor. Successful completion of these objectives will permit more efficient usage of the reactor column and tighter design criteria, increase overall reactor efficiency, and ensure a design that leads to stable reactor behavior when scaling up to large diameter reactors.

  20. ENGINEERING DEVELOPMENT OF SLURRY BUBBLE COLUMN REACTOR (SBCR) TECHNOLOGY

    SciTech Connect

    Bernard A. Toseland

    2000-06-30

    The major technical objectives of this program are threefold: (1) to develop the design tools and a fundamental understanding of the fluid dynamics of a slurry bubble column reactor to maximize reactor productivity, (2) to develop the mathematical reactor design models and gain an understanding of the hydrodynamic fundamentals under industrially relevant process conditions, and (3) to develop an understanding of the hydrodynamics and their interaction with the chemistries occurring in the bubble column reactor. Successful completion of these objectives will permit more efficient usage of the reactor column and tighter design criteria, increase overall reactor efficiency, and ensure a design that leads to stable reactor behavior when scaling up to large diameter reactors.